Science.gov

Sample records for acrylic acid aac

  1. Acrylic acid

    Integrated Risk Information System (IRIS)

    Acrylic acid ( CASRN 79 - 10 - 7 ) Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Eff

  2. Synthesis of carboxymethylcellulose/acrylic acid hydrogels with superabsorbent properties by radiation-initiated crosslinking

    NASA Astrophysics Data System (ADS)

    Fekete, Tamás; Borsa, Judit; Takács, Erzsébet; Wojnárovits, László

    2016-07-01

    Superabsorbent hydrogels were prepared by gamma irradiation from aqueous solutions of carboxymethylcellulose (CMC) and acrylic acid (AAc) with varying CMC:AAc ratio. By partially replacing the CMC with AAc the gelation increased and led to a higher gel fraction and lower water uptake. Moreover, the gelation required significantly milder synthesis conditions. Decreasing both the dose and the solute concentration in the presence of AAc led to gels with higher gel fraction and higher degree of swelling compared to pure CMC gels. Increasing the AAc content up to 10% proved to be very effective, while very high AAc content (over 50%) hindered the gelation process.

  3. Self-assembly and the hemolysis effect of monodisperse N,N-diethylacrylamide/acrylic acid nanogels with high contents of acrylic acid.

    PubMed

    Li, Xueting; Zhao, Di; Shi, Xiaodi; Qiu, Gao; Lu, Xihua

    2016-09-21

    Monodisperse temperature/pH sensitive poly(N,N-diethylacrylamide/acrylic acid) (P(DEA/AAc)) nanogels with high contents of AAc up to 40 wt% have been prepared. In this study, it was unexpectedly found that the polydispersity of the nanogels with 40 wt% AAc strongly depended on the initiator concentration. Monodisperse P(DEA/AA) nanogels were synthesized only at a very low concentration of initiator. The phase transition behavior of the nanogels in water can be tuned by pH and temperature. Due to low polydispersity, the nanogels self-assembled into colloidal crystals at different temperatures below the volume phase transition temperature (VPTT). The sharp Bragg peaks of the crystals were significantly blue-shifted as the concentration of the nanogels was increased. In contrast, the condensed suspensions without crystals still exhibited clear colours resulting from a short-range order structure. The reflection spectra of the coloured suspensions showed that the peak wavelength became a bit longer and much broader. And the reflection intensity of the coloured suspensions was much weaker. Elastic and coloured crosslinked nanogel networks prepared by a one-pot and rapid light-initiated crosslinking method showed responses to pH and temperature. Furthermore, the interaction between the nanogels and peptide melittin was investigated. The results showed that an increasing AAc composition led to more efficient inhibition of the hemolytic activity of melittin. The nanogels with 40 wt% AAc composition completely inhibited hemolytic activity at a nanogel concentration of 400 µg ml(-1). Thus, monodisperse P(DEA/AAc) nanogels of high AAc composition may be developed as efficient substitutes for antibody-based antidotes. Owing to the combined influence of the periodic structure of the crystals of the nanogels and an efficient neutralization effect, the P(DEA/AAc) nanogels show promise to become an integral step for preparing valuable naked-eye biosensors as simple, cheap and

  4. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  5. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  6. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  7. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be...) Acrylamide-acrylic acid resins are produced by the polymerization of acrylamide with partial hydrolysis or...

  8. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  9. Radiation grafting studies of acrylic acid onto cellulose triacetate membranes

    NASA Astrophysics Data System (ADS)

    Mazzei, R. O.; Smolko, E.; Torres, A.; Tadey, D.; Rocco, C.; Gizzi, L.; Strangis, S.

    2002-05-01

    Polymer surface modifications were obtained by the application of radiation treatments, etching and grafting of acrylic acid monomers on different membranes of cellulose triacetate materials. Cellulose triacetate foils from pellet dissolution and commercial cellulose triacetate solid state nuclear track detector membranes were assayed. Irradiation with fission fragments from Cf-252 source to obtain a porous structure, 25 MeV proton beam and Co-60 γ-source to produce peroxides were employed in the experiments. The present work gives the grafting yield of AAc monomer onto CTA membranes as a function of diverse variables including irradiation parameters ( γ-dose, Cf-252 ff irradiation time, proton fluency and electronic energy loss (d E/d x) e), structural parameters (pore diameter and pore density, etching time and etching temperature) and grafting parameters (monomer and Mohr salt concentration, grafting time and grafting temperature).

  10. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid... for use in contact with food subject to the provisions of this section. (a) The ethylene-acrylic...

  11. SOURCE ASSESSMENT: ACRYLIC ACID MANUFACTURE; STATE-OF-THE-ART

    EPA Science Inventory

    This report summarizes data on air emissions from the production of acrylic acid. Hydrocarbons, carbon monoxide, and nitrogen oxide are emitted from various operations. Hydrocarbon emissions consist of acetaldehyde, acetic acid, acetone acrolein, acrylic acid, benzene, phenol, pr...

  12. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  13. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  14. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylamide-acrylic acid resins. 176.110 Section 176... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  15. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  16. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  17. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  18. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  19. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  20. Water swelling properties of the electron beam irradiated PVA-g-AAc hydrogels

    NASA Astrophysics Data System (ADS)

    Wang, Qingguo; Zhou, Xue; Zeng, Jinxia; Wang, Jizeng

    2016-02-01

    In this paper, the electron beam irradiation technology being more suitable for the industry application is explored to fabricate the acrylic acid (AAc) monomer-grafted polyvinyl alcohol (PVA-g-AAc) hydrogels. ATR-IR spectra of the PVA-g-AAc hydrogels shows an obvious absorption peak of the sbnd Cdbnd O group at 1701 cm-1, indicating that the AAc monomers were grafted onto the PVA macromolecules. This paper also studied some effects of the mass ratio of PVA/AAc, pH of buffer solution and irradiation dosage on the water swelling properties of the electron beam irradiated PVA-g-AAc hydrogels. The water swelling ratio of PVA-g-AAc hydrogels decreases with increased irradiation dosage and mass ratio of PVA/AAc, whereas swelling ratio increases with increased pH of buffer solution and soaking time. The water-swelling behavior of PVA-g-AAc hydrogels occurred easily in an alkaline environment, particularly in a buffer solution with pH 9.2. Both PVA-g-AAc hydrogels (PVA/AAc = 1/5, w/w) irradiated with 5 kilogray (kGy) and PVA-g-AAc hydrogels (PVA/AAc = 1/1, w/w) irradiated with 15 kGy could easily absorb water and lead to high water swelling ratios (up to about 600%), which are potential candidates to meet the requirements for some biomedical applications.

  1. GENOTOXICITY OF ACRYLIC ACID, METHYL ACRYLATE, ETHYL ACRYLATE, METHYL METHACRYLATE, AND ETHYL METHACRYLATE IN L5178Y MOUSE LYMPHOMA CELLS (JOURNAL VERSION)

    EPA Science Inventory

    A series of monomeric acrylate/methacrylate esters (methyl acrylate, ethyl acrylate, methyl methacrylate, and ethyl methacrylate) as well as acrylic acid were examined for genotoxic activity in L5178Y mouse lymphoma cells without exogenous activation. All five compounds induced c...

  2. Conductivity of p(AAc) Cryogel and Its Li+, Na+, and K+ Salts for NH3 Sensing

    NASA Astrophysics Data System (ADS)

    Sahiner, Nurettin; Demirci, Sahin; Sel, Kivanc

    2016-04-01

    Poly(acrylic acid) [p(AAc)] cryogel has been synthesized by a cryopolymerization technique under cryogenic conditions. The synthesized p(AAc) cryogel was treated with LiOH, NaOH, and KOH to generate corresponding salt forms of carboxylic acid groups within the p(AAc) cryogel network for activation as p(AAc)-Li+, p(AAc)-Na+, and p(AAc)-K+, respectively. The synthesized p(AAc)-based cryogels were characterized via Fourier-transform infrared (FT-IR) spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The room-temperature electrical conductivity of the p(AAc), p(AAc)-Li+, p(AAc)-Na+, and p(AAc)-K+ cryogels was measured as 10-11 S cm-1, 10-10 S cm-1, 10-9 S cm-1, and 10-8 S cm-1, respectively. Furthermore, the p(AAc) cryogel and its salt forms were tested as sensor materials for NH3 gas by exposing them to NH3 vapor for 60 min under ambient conditions. Upon exposure to NH3 vapor, it was found that the conductivity of the bare p(AAc) and p(AAc)-K+ cryogels increased by up to 105- and 102-fold, respectively, compared with their NH3 unexposed states. The increase in conductivity for the other salt forms of p(AAc) cryogel was about 60-fold compared with their bare form. The conductivity increase for the p(AAc) and p(AAc)-K+ cryogels was therefore further investigated by changing the NH3 vapor exposure time, revealing that these materials could be used as sensors for NH3. It was further found that a 5 min NH3 gas exposure time was sufficient for p(AAc)-K+ cryogel to generate a detectable response via a change in the conductivity of the matrix.

  3. Conductivity of p(AAc) Cryogel and Its Li+, Na+, and K+ Salts for NH3 Sensing

    NASA Astrophysics Data System (ADS)

    Sahiner, Nurettin; Demirci, Sahin; Sel, Kivanc

    2016-07-01

    Poly(acrylic acid) [p(AAc)] cryogel has been synthesized by a cryopolymerization technique under cryogenic conditions. The synthesized p(AAc) cryogel was treated with LiOH, NaOH, and KOH to generate corresponding salt forms of carboxylic acid groups within the p(AAc) cryogel network for activation as p(AAc)-Li+, p(AAc)-Na+, and p(AAc)-K+, respectively. The synthesized p(AAc)-based cryogels were characterized via Fourier-transform infrared (FT-IR) spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The room-temperature electrical conductivity of the p(AAc), p(AAc)-Li+, p(AAc)-Na+, and p(AAc)-K+ cryogels was measured as 10-11 S cm-1, 10-10 S cm-1, 10-9 S cm-1, and 10-8 S cm-1, respectively. Furthermore, the p(AAc) cryogel and its salt forms were tested as sensor materials for NH3 gas by exposing them to NH3 vapor for 60 min under ambient conditions. Upon exposure to NH3 vapor, it was found that the conductivity of the bare p(AAc) and p(AAc)-K+ cryogels increased by up to 105- and 102-fold, respectively, compared with their NH3 unexposed states. The increase in conductivity for the other salt forms of p(AAc) cryogel was about 60-fold compared with their bare form. The conductivity increase for the p(AAc) and p(AAc)-K+ cryogels was therefore further investigated by changing the NH3 vapor exposure time, revealing that these materials could be used as sensors for NH3. It was further found that a 5 min NH3 gas exposure time was sufficient for p(AAc)-K+ cryogel to generate a detectable response via a change in the conductivity of the matrix.

  4. Effect of chemical composition on corneal tissue response to photopolymerized materials comprising 2-hydroxyethyl methacrylate and acrylic acid.

    PubMed

    Lai, Jui-Yang

    2014-01-01

    The purpose of this work was to investigate the relationship between the feed composition of 2-hydroxyethyl methacrylate (HEMA)/acrylic acid (AAc) and hydrogel material compatibility towards ocular anterior segment tissues, particularly the corneal endothelium. The monomer solutions of HEMA and AAc were mixed at varying volume ratios of 92:0, 87:5, 82:10, 77:15, and 72:20, and were subjected to UV irradiation. Then, the 7-mm-diameter membrane implants made from photopolymerized materials were placed into the ocular anterior chamber for 4days and assessed by biomicroscopic examinations, corneal thickness measurements, and quantitative real-time reverse transcription polymerase chain reaction analyses. The poly(HEMA-co-AAc) implants prepared from the solution mixture containing 0-10vol.% AAc displayed good biocompatibility. However, with increasing volume ratio of AAc and HEMA from 15:77 to 20:72, the enhanced inflammatory response, decreased endothelial cell density, and increased ocular score and corneal thickness were observed, probably due to the influence of surface charge of copolymer membranes. On the other hand, the ionic pump function of corneal endothelium exposed to photopolymerized membranes was examined by analyzing the Na(+),K(+)-ATPase alpha 1 subunit (ATP1A1) expression level. The presence of the implants having higher amount of AAc incorporated in the copolymers (i.e., 15.1 to 24.7μmol) and zeta potential (i.e., -38.6 to -56.5mV) may lead to abnormal transmembrane transport. It is concluded that the chemical composition of HEMA/AAc has an important influence on the corneal tissue responses to polymeric biomaterials. PMID:24268266

  5. Segregation of mass at the periphery of N -isopropylacrylamide-co-acrylic-acid microgels at high temperatures

    DOE PAGESBeta

    Hyatt, John S.; Do, Changwoo; Hu, Xiaobo; Choi, Hong Sung; Kim, Jin Woong; Lyon, L. Andrew; Fernandez-Nieves, Alberto

    2015-09-29

    Here, we investigate poly(N-isopropylacrylamide) (pNIPAM) microgels randomly copolymerized with large mol % of protonated acrylic acid (AAc), finding that above the lower critical solution temperature the presence of the acid strongly disrupts pNIPAM's collapse, leading to unexpected new behavior at high temperatures. We see a dramatic increase in the ratio between the radius of gyration and the hydrodynamic radius above the theoretical value for homogeneous spheres, and a corresponding increase of the network length scale, which we attribute to the presence of a heterogeneous polymer distribution that forms due to frustration of pNIPAM's coil-to-globule transition by the AAc. Finally, wemore » analyze this phenomenon using a Debye-Bueche-like scattering contribution as opposed to the Lorentzian term often used, interpreting the results in terms of mass segregation at the particle periphery.« less

  6. Segregation of mass at the periphery of N -isopropylacrylamide-co-acrylic-acid microgels at high temperatures

    NASA Astrophysics Data System (ADS)

    Hyatt, John S.; Do, Changwoo; Hu, Xiaobo; Choi, Hong Sung; Kim, Jin Woong; Lyon, L. Andrew; Fernandez-Nieves, Alberto

    2015-09-01

    We investigate poly(N -isopropylacrylamide) (pNIPAM) microgels randomly copolymerized with large mol % of protonated acrylic acid (AAc), finding that above the lower critical solution temperature the presence of the acid strongly disrupts pNIPAM's collapse, leading to unexpected new behavior at high temperatures. Specifically, we see a dramatic increase in the ratio between the radius of gyration and the hydrodynamic radius above the theoretical value for homogeneous spheres, and a corresponding increase of the network length scale, which we attribute to the presence of a heterogeneous polymer distribution that forms due to frustration of pNIPAM's coil-to-globule transition by the AAc. We analyze this phenomenon using a Debye-Bueche-like scattering contribution as opposed to the Lorentzian term often used, interpreting the results in terms of mass segregation at the particle periphery.

  7. Effect of chemical composition on corneal cellular response to photopolymerized materials comprising 2-hydroxyethyl methacrylate and acrylic acid.

    PubMed

    Lai, Jui-Yang

    2013-10-01

    Characterization of corneal cellular response to hydrogel materials is an important issue in ophthalmic applications. In this study, we aimed to investigate the relationship between the feed composition of 2-hydroxyethyl methacrylate (HEMA)/acrylic acid (AAc) and material compatibility towards corneal stromal and endothelial cells. The monomer solutions of HEMA and AAc were mixed at varying volume ratios of 92:0, 87:5, 82:10, 77:15, and 72:20, and were subjected to UV irradiation. Results of electrokinetic measurements showed that an increase in absolute zeta potential of photopolymerized membranes is observed with increasing the volume ratios of AAc/HEMA. Following 4 days of incubation with various hydrogels, the primary rabbit corneal stromal and endothelial cell cultures were examined for viability, proliferation, and pro-inflammatory gene expression. The samples prepared from the solution mixture containing 0-10 vol.% AAc displayed good cytocompatibility. However, with increasing volume ratio of AAc and HEMA from 15:77 to 20:72, the decreased viability, inhibited proliferation, and stimulated inflammation were noted in both cell types, probably due to the stronger charge-charge interactions. On the other hand, the ionic pump function of corneal endothelial cells exposed to photopolymerized membranes was examined by analyzing the Na(+),K(+)-ATPase alpha 1 subunit (ATP1A1) expression level. The presence of material samples having higher anionic charge density (i.e., zeta potential of -38 to -56 mV) may lead to abnormal transmembrane transport. It is concluded that the chemical composition of HEMA/AAc has an important influence on the corneal stromal and endothelial cell responses to polymeric biomaterials. PMID:23910267

  8. Investigation of Acrylic Acid at High Pressure Using Neutron Diffraction

    PubMed Central

    2014-01-01

    This article details the exploration of perdeuterated acrylic acid at high pressure using neutron diffraction. The structural changes that occur in acrylic acid-d4 are followed via diffraction and rationalized using the Pixel method. Acrylic acid undergoes a reconstructive phase transition to a new phase at ∼0.8 GPa and remains molecular to 7.2 GPa before polymerizing on decompression to ambient pressure. The resulting product is analyzed via Raman and FT-IR spectroscopy and differential scanning calorimetry and found to possess a different molecular structure compared with polymers produced via traditional routes. PMID:24650085

  9. Retention of heavy metal ions on comb-type hydrogels based on acrylic acid and 4-vinylpyridine, synthesized by gamma radiation

    NASA Astrophysics Data System (ADS)

    González-Gómez, Roberto; Ortega, Alejandra; Lazo, Luz M.; Burillo, Guillermina

    2014-09-01

    Two novel comb-type hydrogels based on pH-sensitive monomers (acrylic acid (AAc) and 4-vinylpyridine (4VP) were synthesized by gamma radiation. The systems were as follows: a) comb-type hydrogels of an AAc network followed by grafting of 4VP ((net-PAAc)-g-4VP) and b) comb-type hydrogels of an AAc network grafted onto polypropylene (PP) followed by grafting of 4VP (net-(PP-g-AAc)-g-4VP). The equilibrium isotherms and kinetics were evaluated for copper and zinc ions in aqueous solutions. The Zn(II) retention obtained was 480 mg g-1 and 1086 mg g-1 for (net-PAAc)-g-4VP and net-(PP-g-AAc)-g-4VP, respectively. At concentrations as low as ppm, retention efficiencies of approximately 90% were achieved for Cu(II) on (net-PAAc)-g-4VP and for Zn(II) on net-(PP-g-AAc)-g-4VP. Desorption of the hydrogels was also studied, and the results indicated that they can be used repeatedly in aqueous solutions. For both systems, the adsorption of Cu(II) and Zn(II) obeyed the Freundlich model, indicating heterogeneous sorption, and the retention process occurred by chemisorption. The sorption process follows a pseudo-second-order model.

  10. Micron- and nano-sized poly(N-isopropylacrylamide-co-acrylic acid) latex syntheses and their applications for controlled drug release.

    PubMed

    Lue, Shingjiang Jessie; Chen, Bo-Wei; Shih, Chao-Ming; Chou, Feng-Yi; Lai, Jui-Yang; Chiu, Wen-Yen

    2013-08-01

    Thermo-sensitive poly(N-isopropylacrylamide-co-acrylic acid) (P(NIPAAm-co-AAc)) latex particles were prepared with and without sodium dodecyl sulfate (SDS) surfactant via an emulsion polymerization method. The P(NIPAAm-co-AAc) latex particle sizes were approximately 1.1 microm without SDS addition and the particle sizes were in the nanometer range (59 nm) with SDS at its critical micelle concentration (CMC) of 8 mM. We propose a scheme to demonstrate how the SDS concentration affects the synthesized latex particle size. The lower critical solution temperature (LCST) was hardly influenced by the SDS level but increased with the AAc concentration. The PNIPAAm-co-AAc latex particles were employed as thermo-sensitive drug carriers and 4-acetamidophenol was loaded to study the drug release rates from the nano-gels. The effective drug diffusion coefficients within the nano-gels varied as a function of particle size, AAc content, and temperature. The smaller or AAc-rich hydrogel particles provided sustainable drug release property and have potential use in biomedical applications. PMID:23882758

  11. Drilling fluids containing amps, acrylic acid, itaconic acid polymer

    SciTech Connect

    Bardoliwalla, D.F.

    1987-10-13

    This patent describes an aqueous drilling fluid having present in an amount sufficient to reduce fluid loss of the drilling fluid, at least one polymer of (1) from about 5% to about 50% by weight of 2-acrylamido-2-methylpropane sulfonic acid and (2) from about 95% to about 50% by weight of a second component, there being from 100% to about 80% by weight of acrylic acid and from 0% by weight to about 20% by weight of itaconic acid in the second component. The polymer has a weight average molecular weight of between about 50,000 to about 1,000,000 being in its free acid or partially or completely neutralized form and being at least water dispersible. A method is described of drilling a well into a subterranean formation in which an aqueous drilling fluid is circulated into the well. The step of circulating the drilling fluid contains in an amount sufficient to reduce fluid loss of the drilling fluid, at least one polymer of (1) from about 5% to about 50% by weight of 2-acrylamido-2-methylpropane sulfonic acid and (2) from about 95% to about 50% by weight of a second component. There is from 100% to about 80% by weight of acrylic acid and from 0% by weight to about 20% by weight of itaconic acid in the second component. The polymer has weight average molecular weight of between about 50,000 to about 1,000,000 in its free acid or partially or completely neutralized form and is at least water dispersible.

  12. Radiation grafting of pH-sensitive acrylic acid and 4-vinyl pyridine onto nylon-6 using one- and two-step methods

    NASA Astrophysics Data System (ADS)

    Ortega, Alejandra; Alarcón, Darío; Muñoz-Muñoz, Franklin; Garzón-Fontecha, Angélica; Burillo, Guillermina

    2015-04-01

    Acrylic acid (AAc) and 4-vinyl pyridine (4VP) were γ-ray grafted onto nylon-6 (Ny6) films via pre-irradiation oxidative method. These monomers were grafted using a one-step method to render Ny6-g-(AAc/4VP). A two-step or sequential method was used to render (Ny6-g-AAc)-g-4VP. Random copolymer branches were obtained when the grafting was carried out via one-step method using the two monomers together. The two-step method was applied to graft chains of 4VP on both Ny6 substrate and previously grafted AAc chains (Ny6-g-AAc). The two types of binary copolymers synthesized were characterized to determine the amount of grafted polymers, the thermal behavior (DSC and TGA), the surface composition (XPS), and the pH responsiveness. In the two-step process, it is possible to achieve a higher graft yield, better control of the amount of each monomer, good reversibility in the swelling/deswelling process and shorter time to achieve equilibrium swelling.

  13. Thermo- and pH-sensitive gel membranes based on poly-(acryloyl- L-proline methyl ester)- graft-poly(acrylic acid) for selective permeation of metal ions

    NASA Astrophysics Data System (ADS)

    Hasegawa, Shin; Ohashi, Hitoshi; Maekawa, Yasunari; Katakai, Ryoichi; Yoshida, Masaru

    2005-04-01

    Thermo- and pH-responsive gel membranes were synthesized by γ-ray grafting of pH-responsive poly(acrylic acid) (AAc) onto thermo-responsive polymer gel of acryloyl- L-proline methyl ester (A-ProOMe). The gel membranes of poly(A-ProOMe) with 15 mol% graft chains of AAc exhibited both thermo- and pH-responses. Under the condition (pH 6.0, 30°C) in which the thermo-sensitive unit shrinks and the pH-sensitive unit swells, the selective permeation of Li ion over Co and Ni ions can be achieved.

  14. Segregation of mass at the periphery of N -isopropylacrylamide-co-acrylic-acid microgels at high temperatures

    SciTech Connect

    Hyatt, John S.; Do, Changwoo; Hu, Xiaobo; Choi, Hong Sung; Kim, Jin Woong; Lyon, L. Andrew; Fernandez-Nieves, Alberto

    2015-09-29

    Here, we investigate poly(N-isopropylacrylamide) (pNIPAM) microgels randomly copolymerized with large mol % of protonated acrylic acid (AAc), finding that above the lower critical solution temperature the presence of the acid strongly disrupts pNIPAM's collapse, leading to unexpected new behavior at high temperatures. We see a dramatic increase in the ratio between the radius of gyration and the hydrodynamic radius above the theoretical value for homogeneous spheres, and a corresponding increase of the network length scale, which we attribute to the presence of a heterogeneous polymer distribution that forms due to frustration of pNIPAM's coil-to-globule transition by the AAc. Finally, we analyze this phenomenon using a Debye-Bueche-like scattering contribution as opposed to the Lorentzian term often used, interpreting the results in terms of mass segregation at the particle periphery.

  15. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  16. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  17. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  18. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  19. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  20. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  1. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  2. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  3. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  4. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  5. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  6. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  7. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  8. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  9. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  10. Production of 3-hydroxypropionic acid from acrylic acid by newly isolated rhodococcus erythropolis LG12.

    PubMed

    Lee, Sang-Hyun; Park, Si Jae; Park, Oh-Jin; Cho, Junhyeong; Rhee, Joo Won

    2009-05-01

    A novel microorganism, designated as LG12, was isolated from soil based on its ability to use acrylic acid as the sole carbon source. An electron microscopic analysis of its morphological characteristics and phylogenetic classification by 16S rRNA homology showed that the LG12 strain belongs to Rhodococcus erythropolis. R. erythropolis LG12 was able to metabolize a high concentration of acrylic acid (up to 40 g/l). In addition, R. erythropolis LG12 exhibited the highest acrylic acid-degrading activity among the tested microorganisms, including R. rhodochrous, R. equi, R. rubber, Candida rugosa, and Bacillus cereus. The effect of the culture conditions of R. erythropolis LG12 on the production of 3-hydroxypropionic acid (3HP) from acrylic acid was also examined. To enhance the production of 3HP, acrylic acid-assimilating activity was induced by adding 1 mM acrylic acid to the culture medium when the cell density reached an OD600 of 5. Further cultivation of R. erythropolis LG12 with 40 g/l of acrylic acid resulted in the production of 17.5 g/l of 3HP with a molar conversion yield of 44% and productivity of 0.22 g/I/h at 30 degrees after 72 h. PMID:19494695

  11. Radiation-grafting of thermo- and pH-responsive poly(N-vinylcaprolactam-co-acrylic acid) onto silicone rubber and polypropylene films for biomedical purposes

    NASA Astrophysics Data System (ADS)

    Ferraz, Caroline C.; Varca, Gustavo H. C.; Ruiz, Juan-Carlos; Lopes, Patricia S.; Mathor, Monica B.; Lugão, Ademar B.; Bucio, Emilio

    2014-04-01

    This work focuses on the effects of gamma-ray irradiation conditions on the stimuli-responsiveness of polypropylene (PP) films and silicone (SR) rubber substrates grafted with N-vinylcaprolactam (NVCL) and acrylic acid (AAc). PP films and SR rubber were modified by simultaneous polymerization and grafting of NVCL and AAc, using pre-irradiation oxidative method at a dose rate of 12.23 kGy h-1 and doses ranging from 5 to 70 kGy. NVCL and AAc solutions (1/1, v/v) at 50% monomer concentration (v/v) in toluene were added to the sample substrates, degassed, sealed and heated at 60 and 70 °C for 12 h. After grafting, the samples were soaked in ethanol and distilled water for 24 h successively, followed by drying under vacuum. Samples were characterized by FTIR-ATR, DSC and swelling measurements. Critical points (pH critical or LCST) of grafts were obtained in a pH-environment (pH ranges from 2.2 to 9) and in a thermo-environment (temperature ranges from 22 to 50 °C). Cytotoxicity evaluation was performed using fibroblast BALB/c 3T3 cells. The relationship between NVCL-co-AAc grafting and radiation dose was different for each substrate, PP and SR. At 50% NVCL/AAc concentration in toluene, grafting values were higher for SR than for PP. Despite the fact that PP-g-(NVCL-co-AAc) membrane presented a cytotoxic profile at the highest experimental concentration assayed, cytotoxicity evaluation revealed noncytotoxic profiles for the membranes synthesized highlighting their applications for biomedical purposes.

  12. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  13. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  14. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  15. A New Process for Acrylic Acid Synthesis by Fermentative Process

    NASA Astrophysics Data System (ADS)

    Lunelli, B. H.; Duarte, E. R.; de Toledo, E. C. Vasco; Wolf Maciel, M. R.; Maciel Filho, R.

    With the synthesis of chemical products through biotechnological processes, it is possible to discover and to explore innumerable routes that can be used to obtain products of high addes value. Each route may have particular advantages in obtaining a desired product, compared with others, especially in terms of yield, productivity, easiness to separate the product, economy, and environmental impact. The purpose of this work is the development of a deterministic model for the biochemical synthesis of acrylic acid in order to explore an alternative process. The model is built-up with the tubular reactor equations together with the kinetic representation based on the structured model. The proposed process makes possible to obtain acrylic acid continuously from the sugar cane fermentation.

  16. Biosynthetic pathway for acrylic acid from glycerol in recombinant Escherichia coli.

    PubMed

    Tong, Wenhua; Xu, Ying; Xian, Mo; Niu, Wei; Guo, Jiantao; Liu, Huizhou; Zhao, Guang

    2016-06-01

    Acrylic acid is an important industrial feedstock. In this study, a de novo acrylate biosynthetic pathway from inexpensive carbon source glycerol was constructed in Escherichia coli. The acrylic acid was produced from glycerol via 3-hydroxypropionaldehyde, 3-hydroxypropionyl-CoA, and acrylyl-CoA. The acrylate production was improved by screening and site-directed mutagenesis of key enzyme enoyl-CoA hydratase and chromosomal integration of some exogenous genes. Finally, our recombinant strain produced 37.7 mg/L acrylic acid under shaking flask conditions. Although the acrylate production is low, our study shows feasibility of engineering an acrylate biosynthetic pathway from inexpensive carbon source. Furthermore, the reasons for limited acrylate production and further strain optimization that should be performed in the future were also discussed. PMID:26782744

  17. Using Chou's pseudo amino acid composition to predict protein quaternary structure: a sequence-segmented PseAAC approach.

    PubMed

    Zhang, Shao-Wu; Chen, Wei; Yang, Feng; Pan, Quan

    2008-10-01

    In the protein universe, many proteins are composed of two or more polypeptide chains, generally referred to as subunits, which associate through noncovalent interactions and, occasionally, disulfide bonds to form protein quaternary structures. It has long been known that the functions of proteins are closely related to their quaternary structures; some examples include enzymes, hemoglobin, DNA polymerase, and ion channels. However, it is extremely labor-expensive and even impossible to quickly determine the structures of hundreds of thousands of protein sequences solely from experiments. Since the number of protein sequences entering databanks is increasing rapidly, it is highly desirable to develop computational methods for classifying the quaternary structures of proteins from their primary sequences. Since the concept of Chou's pseudo amino acid composition (PseAAC) was introduced, a variety of approaches, such as residue conservation scores, von Neumann entropy, multiscale energy, autocorrelation function, moment descriptors, and cellular automata, have been utilized to formulate the PseAAC for predicting different attributes of proteins. Here, in a different approach, a sequence-segmented PseAAC is introduced to represent protein samples. Meanwhile, multiclass SVM classifier modules were adopted to classify protein quaternary structures. As a demonstration, the dataset constructed by Chou and Cai [(2003) Proteins 53:282-289] was adopted as a benchmark dataset. The overall jackknife success rates thus obtained were 88.2-89.1%, indicating that the new approach is quite promising for predicting protein quaternary structure. PMID:18427713

  18. Hydrophilic surface modification of acrylate-based biomaterials.

    PubMed

    Arnal-Pastor, M; Comín-Cebrián, S; Martínez-Ramos, C; Monleón Pradas, M; Vallés-Lluch, A

    2016-04-01

    Acrylic polymers have proved to be excellent with regard to cell adhesion, colonization and survival, in vitro and in vivo. Highly ordered and regular pore structures thereof can be produced with the help of polyamide templates, which are removed with nitric acid. This treatment converts a fraction of the ethyl acrylate side groups into acrylic acid, turning poly(ethyl acrylate) scaffolds into a more hydrophilic and pH-sensitive substrate, while its good biological performance remains intact. To quantify the extent of such a modification, and be able to characterize the degree of hydrophilicity of poly(ethyl acrylate), poly(ethyl acrylate) was treated with acid for different times (four, nine and 17 days), and compared with poly(acrylic acid) and a 90/10%wt. EA/AAc copolymer (P(EA-co-AAc)). The biological performance was also assessed for samples immersed in acid up to four days and the copolymer, and it was found that the incorporation of acidic units on the material surface was not prejudicial for cells. This surface modification of 3D porous hydrophobic scaffolds makes easier the wetting with culture medium and aqueous solutions in general, and thus represents an advantage in the manageability of the scaffolds. PMID:26767395

  19. Patterned biofunctional poly(acrylic acid) brushes on silicon surfaces.

    PubMed

    Dong, Rong; Krishnan, Sitaraman; Baird, Barbara A; Lindau, Manfred; Ober, Christopher K

    2007-10-01

    Protein patterning was carried out using a simple procedure based on photolithography wherein the protein was not subjected to UV irradiation and high temperatures or contacted with denaturing solvents or strongly acidic or basic solutions. Self-assembled monolayers of poly(ethylene glycol) (PEG) on silicon surfaces were exposed to oxygen plasma through a patterned photoresist. The etched regions were back-filled with an initiator for surface-initiated atom transfer radical polymerization (ATRP). ATRP of sodium acrylate was readily achieved at room temperature in an aqueous medium. Protonation of the polymer resulted in patterned poly(acrylic acid) (PAA) brushes. A variety of biomolecules containing amino groups could be covalently tethered to the dense carboxyl groups of the brush, under relatively mild conditions. The PEG regions surrounding the PAA brush greatly reduced nonspecific adsorption. Avidin was covalently attached to PAA brushes, and biotin-tagged proteins could be immobilized through avidin-biotin interaction. Such an immobilization method, which is based on specific interactions, is expected to better retain protein functionality than direct covalent binding. Using biotin-tagged bovine serum albumin (BSA) as a model, a simple strategy was developed for immobilization of small biological molecules using BSA as linkages, while BSA can simultaneously block nonspecific interactions. PMID:17880179

  20. Plasma polymerization of acrylic acid onto polystyrene by cyclonic plasma at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Chang, Yi-Jan; Lin, Chin-Ho; Huang, Chun

    2016-01-01

    The cyclonic atmospheric-pressure plasma is developed for chamberless deposition of poly(acrylic acid) film from argon/acrylic acid mixtures. The photoemission plasma species in atmospheric-pressure plasma polymerization was identified by optical emission spectroscopy (OES). The OES diagnosis data and deposition results indicated that in glow discharge, the CH and C2 species resulted from low-energy electron-impact dissociation that creates deposition species, but the strong CO emission lines are related to nondeposition species. The acrylic acid flow rate is seen as the key factor affecting the film growth. The film surface analysis results indicate that a smooth, continuous, and uniform surface of poly(acrylic acid) films can be formed at a relatively low plasma power input. This study reveals the potential of chamberless film growth at atmospheric pressure for large-area deposition of poly(acrylic acid) films.

  1. Radiation curing of polyester resin modified with acrylic acid and its salts

    NASA Astrophysics Data System (ADS)

    Szalińska, H.; Pietrzak, M.; Janowska, G.

    Polyester resin containing acrylic acid or its salts was cured with γ 60Co radiation. The course of curing was examined, the gel content and polymerization shrinkage were measured and also thermographic and IR absorption analyses were carried out. It was found that manganese, iron and copper acrylates inhibited the curing of resin while the remaining additives showed a slightly stimulating action. All the additives decreased the polymerization shrinkage by a factor of 2-3 and iron acrylate by as much as 8 times (up to 1%). They also increased the activation energy of the thermal decomposition of resin, and calcium, barium and copper acrylates increased the thermal stability of resin by 20 K. IR absorption spectra showed that acrylic acid and its salts reacted mainly with the monomeric component of the resin (styrene) whereas iron and copper acrylates first attacked the unsaturated bonds of the oligoester.

  2. 40 CFR 721.10389 - Styrene, copolymer with acrylic acid, salt with alkoxylated alkenylamine (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Styrene, copolymer with acrylic acid... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10389 Styrene, copolymer with acrylic... subject to reporting. (1) The chemical substance identified generically as styrene, copolymer with...

  3. Synthesis and self-assembly of poly(3-hexylthiophene)-block-poly(acrylic acid)

    SciTech Connect

    Li, Zicheng; Ono, Robert J.; Wu, Zong-Quan; Bielawski, Christopher W.

    2011-01-01

    A modular and convenient synthesis of ethynyl end functionalized poly(3-hexylthiophene) in high purity is reported; this material facilitated access to poly(3-hexylthiophene)-block-poly(acrylic acid) which self-assembled into hierarchical structures.

  4. Synthesis and characterization of amylose grafted poly(acrylic acid) and its application in ammonia adsorption.

    PubMed

    Chen, Qing; Yu, Haojie; Wang, Li; Abdin, Zain-Ul; Yang, Xinpeng; Wang, Junhua; Zhou, Weidong; Zhang, Hongtao; Chen, Xiao

    2016-11-20

    Amylose grafted poly(acrylic acid) (Am-g-PAA) was synthesized by graft copolymerization of amylose with acrylic acid. The structure of Am-g-PAA was confirmed by (1)H NMR and FT-IR spectra. The morphology, crystallinity and thermal properties of amylose and Am-g-PAA were investigated by SEM, XRD and TGA, respectively. The highest degree of substitution (DS) of carboxyl group was 1.96 which was obtained after reacted for 1h at 60°C. Acrylic acid to anhydroglucose mole ratio for DS was 19.81. It was found that a large number of carboxyl groups were grafted on the backbone of amylose. It was also found that ammonia adsorption capacity of amylose increased by grafting poly(acrylic acid) on the backbone of amylose. PMID:27561514

  5. Star-shaped polymers of bio-inspired algae core and poly(acrylamide) and poly(acrylic acid) as arms in dissolution of silica/silicate.

    PubMed

    Chauhan, Kalpana; Patiyal, Priyanka; Chauhan, Ghanshyam S; Sharma, Praveen

    2014-06-01

    Silica, in natural waters (due to weathering of rocks) decreases system performance in water processing industry due to scaling. In view of that, the present work involves the synthesis of novel green star shaped additives of algae core (a bio-inspired material as diatom maintains silicic acid equilibrium in sea water) as silica polymerization inhibitors. Star shaped materials with bio-inspired core and poly(acrylamide) [poly(AAm)] and poly(acrylic acid) [poly(AAc)] arms were synthesized by economical green approach. The proficiency was evaluated in 'mini lab' scale for the synthesized APAAm (Algae-g-poly(AAm)) and APAAc (Algae-g-poly(AAc)) dendrimers (star shaped) in colloidal silica mitigation/inhibition at 35 °C and 55 °C. Synthesized dendrimers were equally proficient in silica inhibition at 12 h and maintains ≥450 ppm soluble silica. However, APAAm dendrimers of generation 0 confirmed better results (≈300 ppm) in contrast to APAAc dendrimers in silica inhibition at 55 °C. Additionally, dendrimers also worked as a nucleator for heterogeneous polymerization to inhibit silica homo-polymerization. APAAm dendrimer test set showed no silica deposit for more than 10 days of inhibition. EDX characterization results support nucleator mechanism with Si content of 6.97%-10.98% by weight in silica deposits (SiO2-APAAm dendrimer composites). PMID:24681378

  6. Interaction of photosensitive surfactant with DNA and poly acrylic acid.

    PubMed

    Zakrevskyy, Yuriy; Cywinski, Piotr; Cywinska, Magdalena; Paasche, Jens; Lomadze, Nino; Reich, Oliver; Löhmannsröben, Hans-Gerd; Santer, Svetlana

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes' properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate - for the first time - complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules. PMID:25669583

  7. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    SciTech Connect

    Zakrevskyy, Yuriy Paasche, Jens; Lomadze, Nino; Santer, Svetlana; Cywinski, Piotr; Cywinska, Magdalena; Reich, Oliver; Löhmannsröben, Hans-Gerd

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes’ properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate – for the first time – complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  8. Radiation-induced grafting of acrylic acid onto polypropylene film and its biodegradability

    NASA Astrophysics Data System (ADS)

    Mandal, Dev K.; Bhunia, Haripada; Bajpai, Pramod K.; Chaudhari, C. V.; Dubey, K. A.; Varshney, L.

    2016-06-01

    Polypropylene based commodity polyolefins are widely used in packaging, manufacturing, electrical, pharmaceutical and other applications. The aim of the present work is to study the effect of grafting of acrylic acid on the biodegradability of acrylic acid grafted polypropylene. The effect of different conditions showed that grafting percentage increased with increase in monomer concentration, radiation dose and inhibitor concentration but decreased with increase in radiation dose rate. The maximum grafting of 159.4% could be achieved at optimum conditions. The structure of grafted polypropylene films at different degree of grafting was characterized by EDS, FTIR, TGA, DSC, SEM and XRD. EDS studies showed that the increase in acrylic acid grafting percentage increased the hydrophilicity of the grafted films. FTIR studies indicated the presence of acrylic acid on the surface of polypropylene film. TGA studies revealed that thermal stability decreased with increase in grafting percentage. DSC studies showed that melting temperature and crystallinity of the grafted polypropylene films lower than polypropylene film. SEM studies indicated that increase in acrylic acid grafting percentage increased the wrinkles in the grafted films. The maximum biodegradability could be achieved to 6.85% for 90.5% grafting. This suggested that microorganisms present in the compost could biodegrade acrylic acid grafted polypropylene.

  9. Synthesis of Gold Nanoflowers Encapsulated with Poly(N-isopropylacrylamide-co-acrylic acid) Hydrogels.

    PubMed

    Bae, Saet-Byeol; Lee, Sang-Wha

    2015-10-01

    In this work, hydrogel-coated gold nanoflowers (AuNFs@hydrogel) were facilely prepared. First, gold nanoflowers (AuNFs) were synthesized by reducing gold acid with ascorbic acid in the presence of chitosan biopolymers, and the chitosan-mediated AuNFs were subsequently conjugated with oleic acid with carboxylate groups. Finally, the olefin-conjugated AuNFs were encapsulated with P(NIPAM-co-AAC) hydrogels via a radical polymerization reaction with co-monomer ratio of [NIPAM:AAc = 91:9 wt%]. The encapsulated hydrogels had a lower critical solution temperature (LCST) slightly above the physiological temperature and demonstrated a thermo-sensitive variation of particle size. The hydrogel-coated AuNFs can be utilized as a promising thermo-responsive drug delivery system with a unique optical property. As-prepared samples were characterized by DLS, SEM, TEM, UV-vis and Zeta potential meter. PMID:26726447

  10. Hemocompatibility of Chitosan/poly(acrylic acid) Grafted Polyurethane Tubing

    PubMed Central

    Lee, Hyun-Su; Tomczyk, Nancy; Kandel, Judith; Composto, Russell J.; Eckmann, David M.

    2013-01-01

    The activation and adhesion of platelets or whole blood exposed to chitosan (CH) grafted surfaces is used to evaluate the hemocompatibility of biomaterials. The biomaterial surfaces are polyurethane (PU) tubes grafted with an inner poly(acrylic acid) (PAA) and an outer CH or quaternary ammonium modified CH (CH-Q) brush. The CH, CH-Q and PAA grafted layers were characterized by ellipsometry and fluorescence microscopy. Material wear tests demonstrate that CH (CH-Q) is stably grafted onto PU tubes upon exposure to saline solution for 7 days. Using quartz-crystal microbalances with dissipation (QCM-D), in-situ adsorption of blood plasma proteins on CH and CH-Q compared to a silicon oxide control was measured. The QCM-D results showed that the physically adsorbed plasma protein layer on CH-Q and CH surfaces is softer and more viscous than the protein layer on the SiO2 surface. The CH-Q layer thus has the weakest interaction with plasma proteins. Whole blood and platelet adhesion was reduced by ~92% on CH-Q, which showed the weakest interaction with plasma protein but more viscous adsorbed plasma protein layer, compared to SiO2. Last, to examine the biologic response of platelets and neutrophils to biomaterial surfaces, CH (CH-Q)/PAA, PAA and PU tubes were tested using a Chandler Loop apparatus as an ex vivo model and flow cytometry. The blood adhesion and biologic response results showed that CH and CH-Q reduced adhesion and activation of platelets and neutrophils and improved hemocompatibility relative to other surfaces (PU and PAA). Our studies demonstrated that the properties of physically adsorbed plasma protein layer on biomaterial surfaces correlates with blood coagulation on biomaterial surfaces. PMID:24349719

  11. Hemocompatibility of Chitosan/poly(acrylic acid) Grafted Polyurethane Tubing.

    PubMed

    Lee, Hyun-Su; Tomczyk, Nancy; Kandel, Judith; Composto, Russell J; Eckmann, David M

    2013-12-14

    The activation and adhesion of platelets or whole blood exposed to chitosan (CH) grafted surfaces is used to evaluate the hemocompatibility of biomaterials. The biomaterial surfaces are polyurethane (PU) tubes grafted with an inner poly(acrylic acid) (PAA) and an outer CH or quaternary ammonium modified CH (CH-Q) brush. The CH, CH-Q and PAA grafted layers were characterized by ellipsometry and fluorescence microscopy. Material wear tests demonstrate that CH (CH-Q) is stably grafted onto PU tubes upon exposure to saline solution for 7 days. Using quartz-crystal microbalances with dissipation (QCM-D), in-situ adsorption of blood plasma proteins on CH and CH-Q compared to a silicon oxide control was measured. The QCM-D results showed that the physically adsorbed plasma protein layer on CH-Q and CH surfaces is softer and more viscous than the protein layer on the SiO2 surface. The CH-Q layer thus has the weakest interaction with plasma proteins. Whole blood and platelet adhesion was reduced by ~92% on CH-Q, which showed the weakest interaction with plasma protein but more viscous adsorbed plasma protein layer, compared to SiO2. Last, to examine the biologic response of platelets and neutrophils to biomaterial surfaces, CH (CH-Q)/PAA, PAA and PU tubes were tested using a Chandler Loop apparatus as an ex vivo model and flow cytometry. The blood adhesion and biologic response results showed that CH and CH-Q reduced adhesion and activation of platelets and neutrophils and improved hemocompatibility relative to other surfaces (PU and PAA). Our studies demonstrated that the properties of physically adsorbed plasma protein layer on biomaterial surfaces correlates with blood coagulation on biomaterial surfaces. PMID:24349719

  12. Conversion of (Meth)acrylic acids to methane granular sludge: Initiation by specific anerobic microflora

    SciTech Connect

    Shtarkman, N.B.; Obraztova, A.Y.; Laurinavichyus, K.S.; Galushko, A.S.; Akimenko, V.K.

    1995-03-01

    The role of a specific anaerobic microflora in the initiation of degradation of (meth)acrylic acids to methane by granular sludge from a UASB reactor was investigated. Associations of anaerobic bacteria isolated from the anaerobic sludge, which was used for a long time for treatment of wastewater from (meth)acrylate production, were able to realize the initial stage of (meth)acrylic acid decomposition, i.e., a conversion of acrylic and methacrylic acids to propionic and isobutyric acids, respectively. When added to granules, these association played a role of an {open_quotes}initiator{close_quotes} of the degradation process, which was then continued by the granular sludge microflora utilizing propionate and isobutyrate. Some characteristics of the granules adapted to propionate or isobutyrate are presented. The rates of propionate and isobutyrate consumption by adapted granules is, respectively, 21 and 53 times higher than the values obtained for nonadapted granules. A combined use of {open_quotes}initiating{close_quotes} bacteria and adapted granules provided degradation of (meth)acrylic acids with a maximum methane yield. The possibility is discussed of employing the granules, which are adapted to short-chain fatty acids, and the {open_quotes}initiating{close_quotes} bacteria, which accomplish the initial steps of the organic material decomposition to lower fatty acids, for the conversion of various chemical compounds to methane. 10 refs., 3 figs., 2 tabs.

  13. Radiation modification of water absorption of cassava starch by acrylic acid/acrylamide

    NASA Astrophysics Data System (ADS)

    Kiatkamjornwong, Suda; Chomsaksakul, Wararuk; Sonsuk, Manit

    2000-10-01

    Graft copolymerizations of acrylamide and/or acrylic acid onto cassava starch by a simultaneous irradiation technique using gamma-rays as the initiator were studied with regard to various parameters of importance: the monomer-to-cassava starch ratio, total dose (kGy), dose rate (kGy h -1), acrylamide-to-acrylic acid ratio, and the addition of nitric acid and maleic acid as the additives. Grafting parameters were determined in relation to the water absorption of the saponified graft copolymer. The water absorption of the saponified graft copolymer in salt and buffer solutions of different ionic strengths was also measured, from which the superabsorbent properties are found to be pH sensitive. The starch graft copolymers of acrylamide and acrylic acid give higher water absorption than the starch graft copolymers of either acrylamide or acrylic acid alone. The porosity of the saponified starch graft copolymers prepared by the acrylamide/acrylic acid ratios of 70:30 and 50:50 was much higher than the porosity of copolymers in terms of fine networks. Ionic strength and multi-oxidation states of the saline and buffer solutions markedly decreased the water absorption of the saponified cassava starch grafted superabsorbent polymers.

  14. Functional and surface-active membranes from poly(vinylidene fluoride)-graft-poly(acrylic acid) prepared via RAFT-mediated graft copolymerization.

    PubMed

    Ying, L; Yu, W H; Kang, E T; Neoh, K G

    2004-07-01

    Poly (vinylidene fluoride) (PVDF) with "living" poly (acrylic acid) (PAAc) side chains (PVDF-g-PAAc) was prepared by reversible addition-fragmentation chain transfer (RAFT)-mediated graft copolymerization of acrylic acid (AAc) with the ozone-pretreated PVDF. The chemical composition and structure of the copolymers were characterized by elemental analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The copolymer could be readily cast into pH-sensitive microfiltration (MF) membranes with enriched living PAAc graft chains on the surface (including the pore surfaces) by phase inversion in an aqueous medium. The surface composition of the membranes was determined by X-ray photoelectron spectroscopy. The morphology of the membranes was characterized by scanning electron microscopy. The pore size distribution of the membranes was found to be much more uniform than that of the corresponding membranes cast from PVDF-g-PAAc prepared by the "conventional" free-radical graft copolymerization process. Most important of all, the MF membranes with surface-tethered PAAc macro chain transfer agents, or the living membrane surfaces, could be further functionalized via surface-initiated block copolymerization with N-isopropylacrylamide (NIPAAM) to obtain the PVDF-g-PAAc-b-PNIPAAM MF membranes, which exhibited both pH- and temperature-dependent permeability to aqueous media. PMID:16459627

  15. Synthesis of radiation crosslinked poly(acrylic acid) in the presence of phenyltriethoxysilane

    NASA Astrophysics Data System (ADS)

    Hassan, Safia; Yasin, Tariq

    2014-04-01

    Acrylic acid based superabsorbent hydrogel was prepared using phenyltriethoxysilane (PTES) as polyfunctional monomer. Different amounts of PTES were incorporated in acrylic acid and irradiated at different doses upto maximum of 30 kGy. The crosslinked acrylic acid showed hydrogel properties and its swelling kinetics, gel fraction and equilibrium degree of swelling (EDS) were studied. It was found that the increased PTES concentration decreased the EDS of the hydrogels. Infrared spectroscopy confirmed the crosslinking reaction between the feed components and the existence of siloxane bond. Thermogravimetric analysis showed an increase in the stability of the hydrogels having high PTES content. The swelling of the hydrogel was affected by pH, ionic strength and temperature. These hydrogels showed low swelling in acidic and basic pH range and high swelling around neutral pH. This switchable pH response of these hydrogels can be exploited in environmental and biomedical applications.

  16. Graft Polymerization of Acrylic Acid on a Polytetrafluoroethylene Panel by an Inductively Coupled Plasma

    NASA Astrophysics Data System (ADS)

    Lan, Yan; You, Qingliang; Cheng, Cheng; Zhang, Suzhen; Ni, Guohua; Nagatsu, M.; Meng, Yuedong

    2011-02-01

    Surface modification on a polytetrafluoroethylene (PTFE) panel was performed with sequential nitrogen plasma treatments and surface-initiated polymerization. By introducing COO- groups to the surface of the PTFE panel through grafting polymerization of acrylic acid (AA), a transparent poly (acrylic acid) (PAA) membrane was achieved from acrylic acid solution. Grafting polymerization initiating from the active groups was achieved on the PTFE panel surface after the nitrogen plasma treatment. Utilizing the acrylic acid as monomers, with COO- groups as cross link sites to form reticulation structure, a transparent poly (acrylic acid) membrane with arborescent macromolecular structure was formed on the PTFE panel surface. Analysis methods, such as fourier transform infrared spectroscopy (FTIR), microscopy and X-ray photoelectron spectroscopy (XPS), were utilized to characterize the structures of the macromolecule membrane on the PTFE panel surface. A contact angle measurement was performed to characterize the modified PTFE panels. The surface hydrophilicities of modified PTFE panels were significantly enhanced after the plasma treatment. It was shown that the grafting rate is related to the treating time and the power of plasma.

  17. Synthesis of a novel acrylated abietic acid-g-bacterial cellulose hydrogel by gamma irradiation.

    PubMed

    Abeer, Muhammad Mustafa; Amin, Mohd Cairul Iqbal Mohd; Lazim, Azwan Mat; Pandey, Manisha; Martin, Claire

    2014-09-22

    Acrylated abietic acid (acrylated AbA) and acrylated abietic acid-grafted bacterial cellulose pH sensitive hydrogel (acrylated AbA-g-BC) were prepared by a one-pot synthesis. The successful dimerization of acrylic acid (AA) and abietic acid (AbA) and grafting of the dimer onto bacterial cellulose (BC) was confirmed by 13C solid state NMR as well as FT-IR. X-ray diffraction analysis showed characteristic peaks for AbA and BC; further, there was no effect of increasing amorphous AA content on the overall crystallinity of the hydrogel. Differential scanning calorimetry revealed a glass transition temperature of 80°C. Gel fraction and swelling studies gave insight into the features of the hydrogel, suggesting that it was suitable for future applications such as drug delivery. Scanning electron microscopy observations showed an interesting interpenetrating network within the walls of hydrogel samples with the lowest levels of AA and gamma radiation doses. Cell viability test revealed that the synthesized hydrogel is safe for future use in biomedical applications. PMID:24906785

  18. Radiation synthesis of superabsorbent poly(acrylic acid)-carrageenan hydrogels

    NASA Astrophysics Data System (ADS)

    Francis, Sanju; Kumar, Manmohan; Varshney, Lalit

    2004-04-01

    A series of superabsorbent hydrogels were prepared from carrageenan and partially neutralized acrylic acid by gamma irradiation at room temperature. The gel fraction, swelling kinetics and the equilibrium degree of swelling (EDS) of the hydrogels were studied. It was found that the incorporation of even 1% carrageenan (sodium salt) increases the EDS of the hydrogels from ˜320 to ˜800 g/g. Thermal analysis were carried out to determine the amount of free water and bound water in the hydrogels. Under optimum conditions, poly(acrylic acid)-carrageenan hydrogels with high gel fraction (˜80%) and very high EDS (˜800 g/g) were prepared gamma radiolytically from aqueous solution containing 15% partially neutralized acrylic acid and 1-5% carrageenan. The hydrogels were also found to be sensitive to the pH and the ionic strength of the medium.

  19. Tele-AAC Resolution

    PubMed Central

    Anderson, Kate; Boisvert, Michelle K.; Doneski-Nicol, Janis; Gutmann, Michelle L.; Hall, Nerissa C.; Morelock, Cynthia; Steele, Richard; Cohn, Ellen R.

    2012-01-01

    Approximately 1.3% of all people, or about 4 million Americans, cannot rely on their natural speech to meet their daily communication needs. Telepractice offers a potentially cost-effective service delivery mechanism to provide clinical AAC services at a distance to the benefit of underserved populations in the United States and worldwide. Tele-AAC is a unique cross-disciplinary clinical service delivery model that requires expertise in both telepractice and augmentative and alternative communication (AAC) systems. The Tele-AAC Working Group of the 2012 ISAAC Research Symposium therefore drafted a resolution underscoring the importance of identifying and characterizing the unique opportunities and constraints of Tele-AAC in all aspects of service delivery. These include, but are not limited to: needs assessments; implementation planning; device/system procurement, set-up and training; quality assurance, client progress monitoring, and follow-up service delivery. Tele-AAC, like other telepractice applications, requires adherence to the ASHA Code of Ethics and other policy documents, and state, federal, and international laws, as well as a competent technological infrastructure. The Working Group recommends that institutions of higher education and professional organizations provide training in Tele-AAC service provision. In addition, research and development are needed to create validity measures across Tele-AAC practices (i.e., assessment, implementation, and consultation); determine the communication competence levels achieved by Tele-AAC users; discern stakeholders’ perceptions of Tele-AAC services (e.g., acceptability and viability); maximize Tele-AAC’s capacity to engage multiple team members in AAC assessment and ongoing service; identify the limitations and barriers of Tele-AAC provision; and develop potential solutions. PMID:25945206

  20. Radiation grafting of acrylic and methacrylic acid to cellulose fibers to impart high water sorbency

    SciTech Connect

    Zahran, A.H.; Williams, J.L.; Stannett, V.T.

    1980-04-01

    Acrylic and methacrylic acids have been directly grafted to rayon and cotton using the preirradiation technique with /sup 60/ Co gamma rays. The rate of grafting increased with increasing temperature and monomer concentration, as did the final degree of grafting. The amount and rate of grafting also increased with the total irradiation dose but tended to level off at higher doses, in agreement with the leveling off of the radical content reported previously. Methacrylic acid grafted more and faster than acrylic acid to both rayon and cotton. Methacrylic acid grafted more with rayon than cotton, but acrylic acid gave somewhat similar yields with both fibers. The water abosrbency of the grafted fibers depended strongly on their posttreatment. Decrystallizing with 70% zinc chloride or with hot sodium hydroxidy developed supersorbency. The two treatments in succession, respectively, gave the highest values. Metacrylic acid brought about less sorbency than the corrsponding acrylic acid grafts. Useful levels of grafting and supersorbency could be readily and practically achieved by the methods described.

  1. Poly(acrylic acid) to induce competitive crystallization of a theophylline/oxalic acid cocrystal and a theophylline polymorph

    NASA Astrophysics Data System (ADS)

    Jang, Jisun; Kim, Il Won

    2016-01-01

    Polymeric additives to induce competitive crystallization of pharmaceutical compounds were explored. A cocrystal of theophylline and oxalic acid was used as a model system, and poly(acrylic acid), poly(caprolactone), and poly(ethylene glycol) were the additives. The cocrystal formation was selectively hindered with addition of poly(acrylic acid). First the size of the cocrystals were reduced, and eventually the cocrystallization was inhibited to generate neat theophylline crystals. The theophylline crystals were of a distinctively different crystal structure from known polymorphs, based on powder X-ray diffraction. They were also obtained in nanoscale size, when millimeter-scale crystals formed without poly(acrylic acid). Polymeric additives that could form specific interactions with crystallizing compounds seem to be useful tools for the phase and size control of pharmaceutical crystals.

  2. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical...

  3. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical...

  4. Synthesis and application of novel EB curable polyester urethane acrylate modified by linseed oil fatty acid

    NASA Astrophysics Data System (ADS)

    Jun, Li; Xuecheng, Ju; Min, Yi; Jinshan, Wei; Hongfei, Ha

    1999-06-01

    A novel polyester urethane acrylate resin modified by linseed oil fatty acid (LFA) was synthesized and EB curing coating was formulated in this work. When the coating cured by EB radiation on the timber, the cured coating was possessed of good performances.

  5. Radioluminescence of polyester resin modified with acrylic acid and its salts

    NASA Astrophysics Data System (ADS)

    Szalińska, H.; Wypych, M.; Pietrzak, M.; Szadkowska-Nicze, M.

    Polimal-109 polyester resin and its compounds containing acrylic acid and its salts such as: sodium, potassium, magnesium, calcium, barium, iron, cobalt, copper and manganese acrylates were studied by the radioluminescence method, including isothermal luminescence (ITL) at a radiation temperature of 77 K, thermoluminescence (RTL) and spectral distributions of isothermal luminescence. Measurements of optical absorption at 77 K before and after irradiation of the investigated samples were also carried out. The results obtained have shown that metal ions play a significant part in the processes taking place in the polyester matrix under the influence of γ 60Co radiation.

  6. Continuous process of preparation of n-butyl(meth)acrylate by esterification of (meth)acrylic acid by butanol on thermostable sulfo-cation exchanger

    SciTech Connect

    Zheleznaya, L.L.; Karakhanov, R.A.; Lunin, A.F.; Magadov, R.S.; Meshcheryakov, S.V.; Mkrtychan, V.R.; Fomin, V.A.

    1987-11-10

    The authors propose an effective thermostable sulfo-cation exchanger based on polymers with a system of conjugated bonds, sulfopolyphenylene ketone (SPP) differing from the known cation exchangers by the high thermostability (up to 250/sup 0/C), and also having the effect of the stabilization of the double bond in unsaturated monomers. The combination of inhibiting and cation exchange properties makes it also possible to use these sulfo-cation exchangers in the processes of esterification of (meth)acrylic acids by alcohols without addition of special inhibitors. The SPP catalyst was tested in esterification processes of acrylic an methacrylic acid by butanol at a pilot plant.

  7. Poly (N-isopropylacrylamide)-co-(acrylic acid) microgel/Ag nanoparticle hybrids for the colorimetric sensing of H2O2

    NASA Astrophysics Data System (ADS)

    Han, De-Man; Matthew Zhang, Qiang; Serpe, Michael J.

    2015-01-01

    Poly (N-isopropylacrylamide)-co-(acrylic acid) (pNIPAm-co-AAc) microgels composed of Ag nanoparticles (Ag NPs) have been synthesized and employed for the colorimetric sensing of H2O2. Each pNIPAm-co-AAc microgel, which exhibited a diameter of ~800 nm, contained multiple Ag NPs (diameter of ~5 nm), and solutions of these hybrid materials showed a UV-vis absorption band at ~400 nm. This is due to the excitation of the Ag NP surface plasmon. We go on to show that the intensity of this absorption band is dependent on the concentration of H2O2 in solution. Specifically, in the presence of H2O2 the magnitude of the absorption peak dramatically decreases in a linear fashion over the concentration range of 0.30 to 3.00 μM H2O2 (r2 = 0.9918). We go on to show that the response is selective for H2O2 and can still function in complex mixtures, e.g., we showed that the response is still robust in milk samples. While Ag NPs themselves can exhibit similar responses, this system has many benefits including sample processing and long term stability - i.e., Ag NPs are destabilized in solutions of a certain pH, and aggregate readily. Our microgel/Ag NP hybrids have been shown to be extremely stable and are easily purified prior to use by simple centrifugation/washing protocols. This system is simple and straightforward to use, is low cost, and can be used in complex media, which makes it practical for analyzing complex biological and environmental samples.Poly (N-isopropylacrylamide)-co-(acrylic acid) (pNIPAm-co-AAc) microgels composed of Ag nanoparticles (Ag NPs) have been synthesized and employed for the colorimetric sensing of H2O2. Each pNIPAm-co-AAc microgel, which exhibited a diameter of ~800 nm, contained multiple Ag NPs (diameter of ~5 nm), and solutions of these hybrid materials showed a UV-vis absorption band at ~400 nm. This is due to the excitation of the Ag NP surface plasmon. We go on to show that the intensity of this absorption band is dependent on the concentration

  8. Dehydration of lactic acid to acrylic acid over lanthanum phosphate catalysts: the role of Lewis acid sites.

    PubMed

    Guo, Zhen; Theng, De Sheng; Tang, Karen Yuanting; Zhang, Lili; Huang, Lin; Borgna, Armando; Wang, Chuan

    2016-09-14

    Lanthanum phosphate (LaP) nano-rods were synthesized using n-butylamine as a shape-directing agent (SDA). The resulting catalysts were applied in the dehydration of lactic acid to acrylic acid. Aiming to understand the nature of the active sites, the chemical and physical properties of LaP materials were studied using a variety of characterization techniques. This study showed that the SDA not only affected the porosity of the LaP materials but also modified the acid-base properties. Clearly, the modification of the acid-base properties played a more critical role in determining the catalytic performance than porosity. An optimized catalytic performance was obtained on the LaP catalyst with a higher concentration of Lewis acid sites. Basic sites showed negative effects on the stability of the catalysts. Good stability was achieved when the catalyst was prepared using the appropriate SDA/La ratio. PMID:27514871

  9. Superabsorbent biphasic system based on poly(lactic acid) and poly(acrylic acid)

    NASA Astrophysics Data System (ADS)

    Sartore, Luciana; Pandini, Stefano; Baldi, Francesco; Bignotti, Fabio

    2016-05-01

    In this research work, biocomposites based on crosslinked particles of poly(acrylic acid), commonly used as superabsorbent polymer (SAP), and poly-L-lactic acid (PLLA) were developed to elucidate the role of the filler (i.e., polymeric crosslinked particles) on the overall physico-mechanical behavior and to obtain superabsorbent thermoplastic products. Samples prepared by melt-blending of components in different ratios showed a biphasic system with a regular distribution of particles, with diameter ranging from 5 to 10 μm, within the PLLA polymeric matrix. The polymeric biphasic system, coded PLASA i.e. superabsorbent poly(lactic acid), showed excellent swelling properties, demonstrating that cross-linked particles retain their superabsorbent ability, as in their free counterparts, even if distributed in a thermoplastic polymeric matrix. The thermal characteristics of the biocomposites evidence enhanced thermal stability in comparison with neat PLLA and also mechanical properties are markedly modified by addition of crosslinked particles which induce regular stiffening effect. Furthermore, in aqueous environments the particles swell and are leached from PLLA matrix generating very high porosity. These new open-pore PLLA foams, produced in absence of organic solvents and chemical foaming agents, with good physico-mechanical properties appear very promising for several applications, for instance in tissue engineering for scaffold production.

  10. Determination of acrylamide and acrylic acid by isocratic liquid chromatography with pulsed electrochemical detection.

    PubMed

    Casella, Innocenzo G; Pierri, Marianna; Contursi, Michela

    2006-02-24

    The electrochemical behaviour of the polycrystalline platinum electrode towards the oxidation/reduction of short-chain unsaturated aliphatic molecules such as acrylamide and acrylic acid was investigated in acidic solutions. Analytes were separated by reverse phase liquid chromatographic and quantified using a pulsed amperometric detection. A new two-step waveform, is introduced for detection of acrylamide and acrylic acid. Detection limits (LOD) of 20 nM (1. 4 microg/kg) and 45 nM (3.2 microg/kg) were determined in water solutions containing acrylamide and acrylic acid, respectively. Compared to the classical three-step waveform, the proposed two-step waveform shows favourable analytical performance in terms of LOD, linear range, precision and improved long-term reproducibility. The proposed analytical method combined with clean-up procedure accomplished by Carrez clearing reagent and subsequent extraction with a strong cation exchanger cartridges (SPE), was successfully used for the quantification of low concentrations of acrylamide in foodstuffs such as coffee and potato fries. PMID:16426623

  11. Modification of silicon nitride slip properties by poly(acrylic acid)

    SciTech Connect

    Hackley, V.A.; Maglhan, S.G.

    1996-06-01

    Acrylic-acid based polyelectrolytes are used for dispersion and rheology control of ceramic powder slips. This study focuses on the Si{sub 3}N4/H{sub 2}O/poly(acrylic acid) (PAA) system, with the goal of improving our basic understanding of the mechanisms which may significantly affect slip properties during processing. A variety of experimental techniques were employed, including potentiometric titration, electroacoustic analysis, adsorption isotherms, and controlled-stress rheology. The slips exhibited complex behavior over a wide range of conditions in which solids concentration, PAA molecular weight and concentration, and pH were varied. Polymer charge and conformation were found to have significant impact on the flow properties. Pseudoplastic behavior was attributed to the presence of free polymer. The flow properties were also found to be highly pH dependent.

  12. Preparation of poly(acrylic acid) particles by dispersion polymerization in an ionic liquid.

    PubMed

    Minami, Hideto; Kimura, Akira; Kinoshita, Keigo; Okubo, Masayoshi

    2010-05-01

    Poly(acrylic acid) (PAA) particles were successfully prepared by dispersion polymerization of acrylic acid in ionic liquid, N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoro-methanesulfonyl)amide ([DEME][TFSA]) at 70 degrees C with low hydrolysis grade (35.4%) poly(vinyl alcohol) as stabilizer. Interestingly, the PAA particles were easily extracted as particle state with water. Thus, the PAA particles had a cross-linked structure during the polymerization without cross-linker. Moreover, it was also noted that the cross-linking density of the PAA particles could be controlled by thermal treatment at various temperatures in [DEME][TFSA] utilizing the advantages of nonvolatility and high thermal stability of the ionic liquid. PMID:20043688

  13. Semiconductor nanoparticles in poly((2-dimethylamino)ethyl methacrylate-co-acrylic acid) co-polymers

    NASA Astrophysics Data System (ADS)

    Trandafilović, L. V.; Bibić, N.; Georges, M. K.; Blanuša, J.; Radhakrishnan, T.; Djoković, V.

    2013-11-01

    Nanostructured cadmium selenide (CdSe) and lead sulfide (PbS) semiconductors were prepared in a poly(2-(dimethylamino)ethyl methacrylate-co-acrylic acid) matrix. The obtained nanoparticles were characterized by using optical and structural methods. Co-polymers were synthesized in two different molar ratios of pDMAEMA:acrylic acid monomer units (1:2, 1:1). Transmission electron microscopy analysis confirmed the presence of nano-sized CdSe and PbS particles. In the case of CdSe, a shift of the onset of the optical absorption toward lower wavelengths was observed. X-ray diffraction analysis revealed that both CdSe and PbS nanoparticles have cubic crystal structure.

  14. Preparation of poly (styrene)-b-poly (acrylic acid)/γ-Fe 2O 3 composites

    NASA Astrophysics Data System (ADS)

    Zhang, L. D.; Liu, W. L.; Xiao, C. L.; Yao, J. S.; Fan, Z. P.; Sun, X. L.; Zhang, X.; Wang, L.; Wang, X. Q.

    2011-12-01

    The use of a block copolymer, poly (styrene)-b-poly (acrylic acid) (PS-b-PAA) to prepare a magnetic nanocomposite was investigated. Poly (styrene)-poly (t-butyl acrylate) block copolymer, being synthesized by atom transfer radical polymerization, was hydrolyzed with hydrochloric acid for obtaining PS-b-PAA. The obtained PS-b-PAA was then compounded with the modified γ-Fe2O3, and subsequently the magnetic nanocomposite was achieved. The products were characterized by 1H NMR, FTIR, gel permeation chromatography, thermogravimetric analysis, transmission electron microscopy and vibrating sample magnetometer. The results showed that the nanocomposites exhibited soft magnetism, with the mean diameter of 100 nm approximately.

  15. pH effect of coagulation bath on the characteristics of poly(acrylic acid)-grafted and poly(4-vinylpyridine)-grafted poly(vinylidene fluoride) microfiltration membranes.

    PubMed

    Ying, Lei; Zhai, Guangqun; Winata, A Y; Kang, E T; Neoh, K G

    2003-09-15

    The poly(acrylic acid)-graft-poly(vinylidene fluoride) (PAAc-g-PVDF) and poly(4-vinylpyridine)-graft-poly(vinylidene fluoride) (P4VP-g-PVDF) copolymers were obtained by thermally induced molecular graft copolymerization of acrylic acid (AAc) and 4-vinylpyridine (4VP), respectively, with the ozone-pretreated poly(vinylidene fluoride) (PVDF) in N-methyl-2-pyrrolidone (NMP) solution. Microfiltration (MF) membranes were prepared from the respective copolymers by phase inversion in aqueous media. The effects of pH of the coagulation bath on the physicochemical and morphological characteristics of the membranes were investigated. The surface compositions of the membranes were determined by X-ray photoelectron spectroscopy (XPS). The surface graft concentration of the AAc polymer for the PAAc-g-PVDF MF membrane increased with decreasing pH value of the coagulation bath. Completely opposite pH-dependent behavior was observed for the surface graft concentration of the 4VP polymer in the P4VP-g-PVDF MF membranes. A substantial increase in mean pore size was observed for the PAAc-g-PVDF MF membranes cast in basic coagulation baths of increasing pH. In the case of the P4VP-g-PVDF MF membranes, a substantial increase in mean pore size was observed for membranes cast in low pH (acidic) baths. The permeation rate of aqueous solutions through the PAAc-g-PVDF and P4VP-g-PVDF MF membranes exhibited a reversible dependence on the pH of the solution, with the membranes cast near the neutral pH exhibiting the highest sensitivity to changes in permeate pH. PMID:12962674

  16. Ultrafine metal particles immobilized on styrene/acrylic acid copolymer particles

    SciTech Connect

    Tamai, Hisashi; Hamamoto, Shiro; Nishiyama, Fumitaka; Yasuda, Hajime

    1995-04-01

    Ultrafine metal particles immobilized on styrene/acrylic acid copolymer fine particles were produced by reducing the copolymer particles-metal ion complexes or refluxing an ethanol solution of metal ions in the presence of copolymer particles. The size of metal particles formed by reduction of the complex is smaller than that by reflux of the metal ion solution and depends on the amount of metal ions immobilized.

  17. Influence of ozone and paracetic acid disinfection on adhesion of resilient liners to acrylic resin

    PubMed Central

    2016-01-01

    PURPOSE The aim of this study was to evaluate the effect of paracetic acid (PAA) and ozone disinfection on the tensile bond strength (TBS) of silicone-based resilient liners to acrylic resins. MATERIALS AND METHODS One hundred and twenty dumbbell shaped heat-polymerized acrylic resins were prepared. From the mid segment of the specimens, 3 mm of acrylic were grinded off and separated parts were reattached by resilient liners. The specimens were divided into 2 control (control1, control7) and 4 test groups of PAA and ozone disinfection (PAA1, PAA7, ozone1 and ozone7; n=10). While control groups were immersed in distilled water for 10 min (control1) and 7 days (control7), test groups were subjected to PAA (16 g/L) or ozone rich water (4 mg/L) for 1 cycle (10 min for PAA and 60 min for ozone) per day for 7 days prior to tensile tests. Measurements of the TBS were analyzed using 3-way ANOVA and Tukey's HSD test. RESULTS Adhesive strength of Mollosil decreased significantly by application of ozone disinfection. PAA disinfection had no negative effect on the TBS values of Mollosil and Molloplast B to acrylic resin. Single application of ozone disinfection did not have any negative effect on TBS values of Molloplast B, but prolonged exposure to ozone decreased its adhesive strength. CONCLUSION The adhesion of resilient liners to acrylic was not adversely affected by PAA disinfection. Immersion in ozonated water significantly decreased TBS of Mollosil. Prolonged exposure to ozone negatively affects adhesion of Molloplast B to denture base materials. PMID:27555898

  18. 2-Fatty acrylic acids: new highly derivatizable lipophilic platform molecules

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This paper reports the incorporation of an alpha-methylene unit into fatty acid skeletons. Since the new olefin is conjugated with the carboxylate, it is susceptible to 1,4- (Michael) additions. We have used multifunctional thiols and amines for additions at the methylene. The resulting products ...

  19. A density functional study on dielectric properties of acrylic acid grafted polypropylene

    NASA Astrophysics Data System (ADS)

    Ruuska, Henna; Arola, Eero; Kortelainen, Tommi; Rantala, Tapio T.; Kannus, Kari; Valkealahti, Seppo

    2011-04-01

    Influence of acrylic acid grafting of isotactic polypropylene on the dielectric properties of the polymer is investigated using density functional theory (DFT) calculations, both in the molecular modeling and three-dimensional (3D) bulk periodic system frameworks. In our molecular modeling calculations, polarizability volume, and polarizability volume per mass which reflects the permittivity of the polymer, as well as the HOMO-LUMO gap, one of the important measures indicating the electrical breakdown voltage strength, were examined for oligomers with various chain lengths and carboxyl mixture ratios. When a polypropylene oligomer is grafted with carboxyl groups (cf. acrylic acid), our calculations show that the increase of the polarizability volume α' of the oligomer is proportional to the increase of its mass m, while the ratio {{α^ ' } { α^ ' } m} decreases from the value of a pure polymer when increasing the mixture ratio. The decreasing ratio of {{α^ ' } {α^ ' } m} under carboxyl grafting indicates that the material permittivity might also decrease if the mass density of the material remains constant. Furthermore, our calculations show that the HOMO-LUMO gap energy decreases by only about 15% in grafting, but this decrease seems to be independent on the mixture ratio of carboxyl. This indicates that by doping polymers with additives better dielectric properties can be tailored. Finally, using the first-principles molecular DFT results for polarizability volume per mass in connection with the classical Clausius-Mossotti relation, we have estimated static permittivity for acrylic acid grafted polypropylene, assuming the structural density keeping constant under grafting. The computed permittivity values are in a qualitative agreement with the recent experiments, showing increasing tendency of the permittivity as a function of the grafting composition. In order to validate our molecular DFT based approach, we have also carried out extensive three

  20. A density functional study on dielectric properties of acrylic acid grafted polypropylene.

    PubMed

    Ruuska, Henna; Arola, Eero; Kortelainen, Tommi; Rantala, Tapio T; Kannus, Kari; Valkealahti, Seppo

    2011-04-01

    Influence of acrylic acid grafting of isotactic polypropylene on the dielectric properties of the polymer is investigated using density functional theory (DFT) calculations, both in the molecular modeling and three-dimensional (3D) bulk periodic system frameworks. In our molecular modeling calculations, polarizability volume, and polarizability volume per mass which reflects the permittivity of the polymer, as well as the HOMO-LUMO gap, one of the important measures indicating the electrical breakdown voltage strength, were examined for oligomers with various chain lengths and carboxyl mixture ratios. When a polypropylene oligomer is grafted with carboxyl groups (cf. acrylic acid), our calculations show that the increase of the polarizability volume α' of the oligomer is proportional to the increase of its mass m, while the ratio α'/m decreases from the value of a pure polymer when increasing the mixture ratio. The decreasing ratio of α'/m under carboxyl grafting indicates that the material permittivity might also decrease if the mass density of the material remains constant. Furthermore, our calculations show that the HOMO-LUMO gap energy decreases by only about 15% in grafting, but this decrease seems to be independent on the mixture ratio of carboxyl. This indicates that by doping polymers with additives better dielectric properties can be tailored. Finally, using the first-principles molecular DFT results for polarizability volume per mass in connection with the classical Clausius-Mossotti relation, we have estimated static permittivity for acrylic acid grafted polypropylene, assuming the structural density keeping constant under grafting. The computed permittivity values are in a qualitative agreement with the recent experiments, showing increasing tendency of the permittivity as a function of the grafting composition. In order to validate our molecular DFT based approach, we have also carried out extensive three-dimensional bulk periodic first

  1. Bioinspired bioadhesive polymers: dopa-modified poly(acrylic acid) derivatives.

    PubMed

    Laulicht, Bryan; Mancini, Alexis; Geman, Nathanael; Cho, Daniel; Estrellas, Kenneth; Furtado, Stacia; Hopson, Russell; Tripathi, Anubhav; Mathiowitz, Edith

    2012-11-01

    The one-step synthesis and characterization of novel bioinspired bioadhesive polymers that contain Dopa, implicated in the extremely adhesive byssal fibers of certain gastropods, is reported. The novel polymers consist of combinations of either of two polyanhydride backbones and one of three amino acids, phenylalanine, tyrosine, or Dopa, grafted as side chains. Dopa-grafted hydrophobic backbone polymers exhibit as much as 2.5 × the fracture strength and 2.8 × the tensile work of bioadhesion of a commercially available poly(acrylic acid) derivative as tested on live, excised, rat intestinal tissue. PMID:23008096

  2. Injectable hydrogel as stem cell scaffolds from the thermosensitive terpolymer of NIPAAm/AAc/HEMAPCL

    PubMed Central

    Lian, Sheng; Xiao, Yan; Bian, Qingqing; Xia, Yu; Guo, Changfa; Wang, Shenguo; Lang, Meidong

    2012-01-01

    A series of biodegradable thermosensitive copolymers was synthesized by free radical polymerization with N-isopropylacrylamide (NIPAAm), acrylic acid (AAc) and macromer 2-hydroxylethyl methacrylate-poly(ɛ-caprolactone) (HEMAPCL). The structure and composition of the obtained terpolymers were confirmed by proton nuclear magnetic resonance spectroscopy, while their molecular weight was measured using gel permeation chromatography. The copolymers were dissolved in phosphate-buffered saline (PBS) solution (pH = 7.4) with different concentrations to prepare hydrogels. The lower critical solution temperature (LCST), cloud point, and rheological property of the hydrogels were determined by differential scanning calorimetry, ultraviolet-visible spectrometry, and rotational rheometry, respectively. It was found that LCST of the hydrogel increased significantly with the increasing NIPAAm content, and hydrogel with higher AAc/HEMAPCL ratio exhibited better storage modulus, water content, and injectability. The hydrogels were formed by maintaining the copolymer solution at 37°C. The degradation experiment on the formed hydrogels was conducted in PBS solution for 2 weeks and demonstrated a less than 20% weight loss. Scanning electron microscopy was also used to study the morphology of the hydrogel. The copolymer with NIPAAm/AAc/HEMAPCL ratio of 88:9.6:2.4 was bioconjugated with type I collagen for the purpose of biocompatibility enhancement. In-vitro cytotoxicity of the hydrogels both with and without collagen was also addressed. PMID:23028218

  3. Radiation synthesis of eco-friendly water reducing sulfonated starch/acrylic acid hydrogel designed for cement industry

    NASA Astrophysics Data System (ADS)

    Abd El-Rehim, H. A.; Hegazy, El-Sayed A.; Diaa, D. A.

    2013-04-01

    Starch was treated with chlorosulfonic acid to obtain sulfonated starch. Acrylic acid/sulfonated starch semi-interpenetrated network IPN of different compositions was prepared using ionizing radiation. Swelling of prepared IPNs at different environmental conditions was studied. The possible use of sulfonated starch/acrylic acid IPN as a water-retarding agent in the cement industry was investigated. ζ-potential measurements were used to determine the stability of the colloidal cement—SS/AA and cement -poly-naphthalene sulfonic acid (SNF) water retarding mixtures. Sulfonated starch/acrylic acid water-retarding property was influenced by hydrogel concentration and composition. Sulfonated starch/acrylic acid IPN admixture has a great effect on the cement initial setting time. Using 2% of SS/AA or SNF resulted in an increase in initial setting time by 2 and 1 h respectively, if compared with native cement initial setting time. The results showed that the synthetic commercial super-plasticizers could be replaced by an eco-friendly water-retarding sulfonated starch/acrylic acid IPN in the cement industry.

  4. Temperature and pH responsiveness of poly-(DMAA-co-unsaturated carboxylic acid) hydrogels synthesized by UV-irradiation

    NASA Astrophysics Data System (ADS)

    Kakinoki, Sachiro; Kaetsu, Isao; Nakayama, Masashi; Sutani, Kouichi; Uchida, Kumao; Yukutake, Kouji

    2003-07-01

    Stimuli-responsive polyampholyte hydrogels were synthesized by the copolymerization of dimethylaminoethyl methacrylate (DMAA) and acrylic acid (AAc) or itaconic acid (IAc) by UV-irradiation. Temperature and pH responsiveness of these hydrogels were studied. The temperature responsiveness of poly-(DMAA-co-AAc, IAc) hydrogels shown in change of water content became dull compared to that of DMAA homo-polymer hydrogel. The water content of the poly-(DMAA-co-AAc, IAc) hydrogels showed a minimum at pH 8, and increased in more acidic and alkaline regions. This fact can be attributed to the coexistence of anions and cations in the poly-(DMAA-co-AAc, IAc) hydrogels. The poly-(DMAA-co-AAc, IAc) hydrogels were polyampholyte having both temperature responsiveness and pH responsiveness.

  5. Predicting lysine phosphoglycerylation with fuzzy SVM by incorporating k-spaced amino acid pairs into Chou׳s general PseAAC.

    PubMed

    Ju, Zhe; Cao, Jun-Zhe; Gu, Hong

    2016-05-21

    As a new type of post-translational modification, lysine phosphoglycerylation plays a key role in regulating glycolytic process and metabolism in cells. Due to the traditional experimental methods are time-consuming and labor-intensive, it is important to develop computational methods to identify the potential phosphoglycerylation sites. However, the prediction performance of the existing phosphoglycerylation site predictor is not satisfactory. In this study, a novel predictor named CKSAAP_PhoglySite is developed to predict phosphoglycerylation sites by using composition of k-spaced amino acid pairs and fuzzy support vector machine. On the one hand, after many aspects of assessments, we find the composition of k-spaced amino acid pairs is more suitable for representing the protein sequence around the phosphoglycerylation sites than other encoding schemes. On the other hand, the proposed fuzzy support vector machine algorithm can effectively handle the imbalanced and noisy problem in phosphoglycerylation sites training dataset. Experimental results indicate that CKSAAP_PhoglySite outperforms the existing phosphoglycerylation site predictor Phogly-PseAAC significantly. A matlab software package for CKSAAP_PhoglySite can be freely downloaded from https://github.com/juzhe1120/Matlab_Software/blob/master/CKSAAP_PhoglySite_Matlab_Software.zip. PMID:26908349

  6. Antimicrobial effects of esters and amides of 3-(5-nitro-2-furyl)acrylic acid.

    PubMed

    Kellová, G; Sturdík, E; Stibrányi, L; Drobnica, L; Augustín, J

    1984-01-01

    The effect of 18 newly synthesized esters and amides of 3-(5-nitro-2-furyl)acrylic acid on bacteria (Escherichia coli, Staphylococcus aureus), yeasts (Saccharomyces cerevisiae, Candida albicans), molds (Aspergillus niger, Penicillium cyclopium, Rhizopus oryzae) and algae (Chlorella pyrenoidosa, Euglena gracilis, Scenedesmus obliquus) was investigated. The MIC values revealed antimycotic, antialgal and antibacterial activity of the studied derivatives. The antimycotic activity was found to decrease with increasing the length of the alkyl chain of esters and after introduction of amino nitrogen into the furylethylene backbone. The inhibitory effect on growth is caused by blocking bioenergetic processes, glycolysis in particular. PMID:6714854

  7. Ferromagnetic resonance spectroscopy of carboxylated cobalt-containing nanocomposite ethyl methacrylate/acrylic acid copolymers

    NASA Astrophysics Data System (ADS)

    Voytsihovskaya, S. A.; Sokolov, M. E.; Panyushkin, V. T.; Gromov, P. Yu.; Shcherbina, A. A.; Matveev, V. V.

    2013-01-01

    We have used ferromagnetic resonance spectroscopy to study the effect of the concentration of cobalt nanoparticles (5-9 nm) incorporated into ethyl methacrylate/acrylic acid copolymers (monomer ratios 100:1 and 10:1) on the magnitude of the resonant field in ferromagnetic resonance and on the effective magnetization of thin-film samples of these nanocomposite polymer materials. The cobalt nanoparticles were obtained by thermolysis of Co2(CO)8 in 5% solutions of the indicated copolymers in toluene. From the solutions obtained, we prepared films of thickness 1 μm on aluminum substrates.

  8. Thermal destruction of copolymers of polypropylene glycol maleate with acrylic acid

    NASA Astrophysics Data System (ADS)

    Burkeev, M. Zh.; Sarsenbekova, A. Zh.; Tazhbaev, E. M.; Figurinene, I. V.

    2015-12-01

    The results from thermogravimetric and kinetic studies of copolymers of polypropylene glycol maleate with acrylic acid at different molar ratios are presented. The results from conventional thermogravimetric studies are used to determine kinetic characteristics of the process of thermal decomposition, i.e., activation energy and pre-exponential factors. These parameters are determined in three ways: the Achar, Freeman-Carroll, and Sharp-Wentworth methods. Activation energies calculated using all the three methods confirm the dependence of the destruction process on the ratio of components in a synthesized copolymer. It is shown that the obtained values of the activation energies and thermodynamic characteristics allow us to predict a copolymer's composition.

  9. Stabilization of mid-sized silicon nanoparticles by functionalization with acrylic acid

    NASA Astrophysics Data System (ADS)

    Bywalez, Robert; Karacuban, Hatice; Nienhaus, Hermann; Schulz, Christof; Wiggers, Hartmut

    2012-01-01

    We present an enhanced method to form stable dispersions of medium-sized silicon nanoparticles for solar cell applications by thermally induced grafting of acrylic acid to the nanoparticle surface. In order to confirm their covalent attachment on the silicon nanoparticles and to assess the quality of the functionalization, X-ray photoelectron spectroscopy and diffuse reflectance infrared Fourier spectroscopy measurements were carried out. The stability of the dispersion was elucidated by dynamic light scattering and Zeta-potential measurements, showing no sign of degradation for months.

  10. Pharmacokinetics of copolymers of N-vinylpyrrolidone with acrylic acid. Article 1

    SciTech Connect

    Rafikov, R.Z.; Sakhibov, A.D.; Akhmedzhanov, R.I.; Aliev, K.U.

    1987-01-01

    The authors studied the pharmacokinetics of the copolymers of n-vinyl-pyrrolidone (I) with acrylic acid (II) (copolymer III) using the radioactive isotope /sup 125/I. In experiments on mice, they studied the distribution of a copolymer of I with II (/sup 125/I-III) in the organism of the animals. The content of /sup 125/I-III and its possible radioactive metabolites in the blood and organs of mice after a single intravenous administration of the given preparation is shown. The radioactivity of organs after butanol extraction is presented.

  11. Poly-N-Isopropylacrylamide/acrylic Acid Copolymers for the Generation of Nanostructures at Mica Surfaces and as Hydrophobic Host Systems for the Porin MspA from Mycobacterium smegmatis.

    PubMed

    Gamage, Pubudu; Basel, Matthew T; Lovell, Kimberly; Pokhrel, Megh Raj; Battle, Deletria; Ito, Takashi; Pavlenok, Mikhail; Niederweis, Michael; Bossmann, Stefan H

    2009-09-17

    The work presented here aims at utilizing poly-N-isopropyl-acrylamide/acrylic acid copolymers to create nanostructured layers on mica surfaces by a simple spin-casting procedure. The average composition of the copolymers determined by elemental analysis correlates excellently with the feed composition indicating that the radical polymerization process is statistical. The resulting surfaces were characterized by Atomic Force Microscopy (magnetic AC-mode) at the copolymer/air interface. Postpolymerization modification of the acrylic acid functions with perfluoro-octyl-iodide decreased the tendency towards spontaneous formation of nanopores. Crosslinking of individual polymer chains permitted the generation of ultraflat layers, which hosted the mycobacterial channel protein MspA, without compromising its channel function. The comparison of copolymers of very similar chemical composition that have been prepared by living radical polymerization and classic radical polymerization indicated that differences in polydispersity played only a minor role when poly-N-isopropyl-acrylamide/acrylic acid copolymers were spincast, but a major role when copolymers featuring the strongly hydrophobic perfluoro-octyl-labels were used. The mean pore diameters were 23.8+/-4.4 nm for P[(NIPAM)(95.5)-co-(AA)(4.5)] (PDI (polydispersity index)=1.55) and 21.8+/-4.2 nm for P[(NIPAM)(95.3)-co-(AA)(4.7)] (PDI=1.25). The depth of the nanopores was approx. 4 nm. When depositing P[(NIPAM)(95)-co-(AA)(2.8)-AAC(8)F(17 2.2)] (PDI=1.29) on Mica, the resulting mean pore diameter was 35.8+/-7.1 nm, with a depth of only 2 nm. PMID:20161351

  12. pH- and Electro-Responsive Properties of Poly(acrylic acid) and Poly(acrylic acid)-block-poly(acrylic acid-grad-styrene) Brushes Studied by Quartz Crystal Microbalance with Dissipation Monitoring.

    PubMed

    Borisova, O V; Billon, L; Richter, R P; Reimhult, E; Borisov, O V

    2015-07-14

    We report on the synthesis of novel pH- and electro-responsive polyelectrolyte brushes from a gold substrate by direct one-step nitroxide-mediated polymerization of acrylic acid (AA) or copolymerization of AA and styrene (S). In the latter case, amphiphilic brushes of block-gradient copolymers PAA-b-(PAA-grad-PS) comprising one PAA block and one block with the gradient sequence of AA and S were obtained. The block-gradient copolymers are initiated from the surface by the start of the PAA block. The brushes were characterized by XPS and ellipsometry. (1)H NMR confirmed the gradient sequence of the PAA-grad-PS copolymer block. The pH- and electro-responsive properties of the brushes were studied by quartz crystal microbalance with dissipation monitoring (QCM-D) in combination with electrochemistry. This method provides evidence of swelling of the PAA brushes proportional to the contour length of the chains at elevated pH, whereas the response functions of the block-gradient copolymers are more complex and point to intermolecular aggregation in the brush at low pH. Monitoring of the changes in resonance frequency and dissipation of the QCM-D also demonstrates that application of negative voltage to the substrate leads to swelling of the brush; application of a positive voltage provokes only a transient collapse of the brush in proportion to the applied voltage. PMID:26070329

  13. Characterization of bioactive RGD peptide immobilized onto poly(acrylic acid) thin films by plasma polymerization

    NASA Astrophysics Data System (ADS)

    Seo, Hyun Suk; Ko, Yeong Mu; Shim, Jae Won; Lim, Yun Kyong; Kook, Joong-Ki; Cho, Dong-Lyun; Kim, Byung Hoon

    2010-11-01

    Plasma surface modification can be used to improve the surface properties of commercial pure Ti by creating functional groups to produce bioactive materials with different surface topography. In this study, a titanium surface was modified with acrylic acid (AA) using a plasma treatment and immobilized with bioactive arginine-glycine-aspartic acid (RGD) peptide, which may accelerate the tissue integration of bone implants. Both terminals containing the -NH2 of RGD peptide sequence and -COOH of poly(acrylic acid) (PAA) thin film were combined with a covalent bond in the presence of 1-ethyl-3-3-dimethylaminopropyl carbodiimide (EDC). The chemical structure and morphology of AA film and RGD immobilized surface were investigated by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR), atomic force microscopy (AFM), and scanning electron microscopy (SEM). All chemical analysis showed full coverage of the Ti substrate with the PAA thin film containing COOH groups and the RGD peptide. The MC3T3-E1 cells were cultured on each specimen, and the cell alkaline phosphatase (ALP) activity were examined. The surface-immobilized RGD peptide has a significantly increased the ALP activity of MC3T3-E1 cells. These results suggest that the RGD peptide immobilization on the titanium surface has an effect on osteoblastic differentiation of MC3T3-E1 cells and potential use in osteo-conductive bone implants.

  14. Chitosan-poly(acrylic) acid polyionic complex: in vivo study to demonstrate prolonged gastric retention.

    PubMed

    Torrado, Susana; Prada, Pablo; de la Torre, Paloma M; Torrado, Santiago

    2004-02-01

    The aim of this study was to develop a chitosan-poly(acrylic) acid based controlled drug release system for gastric antibiotic delivery. Different mixtures of amoxicillin (A), chitosan (CS), and poly(acrylic) acid (PAA) were employed to obtain these polyionic complexes. A non-invasive method was employed for determining the gastric residence time of the formulations. It was studied the swelling behavior and drug release from these complexes. Gastric emptying rate study was performed by means of the [13C]octanoic acid breath test. The gastric emptying rates of two different formulations (conventional and gastric retentive system) were studied. Swelling studies indicated that the extent of swelling was greater in the polyionic complexes than in the single chitosan formulations. The amoxicillin diffusion from the hydrogels was controlled by the polymer/drug interaction. The property of these complexes to control the solute diffusion depends on the network mesh size, which is a significant factor in the overall behavior of the hydrogels. The gastric half-emptying time of the polyionic complex was significantly delayed compared to the reference formulation, showing mean values of 164.32+/-26.72 and 65.06+/-11.50min, respectively (P<0.01). The results of this study suggest that, these polyionic complexes are good systems for specific gastric drug delivery. PMID:14609680

  15. Precision synthesis of bio-based acrylic thermoplastic elastomer by RAFT polymerization of itaconic acid derivatives.

    PubMed

    Satoh, Kotaro; Lee, Dong-Hyung; Nagai, Kanji; Kamigaito, Masami

    2014-01-01

    Bio-based polymer materials from renewable resources have recently become a growing research focus. Herein, a novel thermoplastic elastomer is developed via controlled/living radical polymerization of plant-derived itaconic acid derivatives, which are some of the most abundant renewable acrylic monomers obtained via the fermentation of starch. The reversible addition-fragmentation chain-transfer (RAFT) polymerizations of itaconic acid imides, such as N-phenylitaconimide and N-(p-tolyl)itaconimide, and itaconic acid esters, such as di-n-butyl itaconate and bis(2-ethylhexyl) itaconate, are examined using a series of RAFT agents to afford well-defined polymers. The number-average molecular weights of these polymers increase with the monomer conversion while retaining relatively narrow molecular weight distributions. Based on the successful controlled/living polymerization, sequential block copolymerization is subsequently investigated using mono- and di-functional RAFT agents to produce block copolymers with soft poly(itaconate) and hard poly(itaconimide) segments. The properties of the obtained triblock copolymer are evaluated as bio-based acrylic thermoplastic elastomers. PMID:24243816

  16. Acrylic-acid-functionalized PolyHIPE scaffolds for use in 3D cell culture.

    PubMed

    Hayward, Adam S; Sano, Naoko; Przyborski, Stefan A; Cameron, Neil R

    2013-12-01

    This study describes the development of a functional porous polymer for use as a scaffold to support 3D hepatocyte culture. A high internal phase emulsion (HIPE) is prepared containing the monomers styrene (STY), divinylbenzene (DVB), and 2-ethylhexyl acrylate (EHA) in the external oil phase and the monomer acrylic acid (Aa) in the internal aqueous phase. Upon thermal polymerization with azobisisobutyronitrile (AIBN), the resulting porous polymer (polyHIPE) is found to have an open-cell morphology and a porosity of 89%, both suitable characteristics for 3D cell scaffold applications. X-ray photo-electron spectroscopy reveals that the polyHIPE surface contained 7.5% carboxylic acid functionality, providing a useful substrate for subsequent surface modifications and bio-conjugations. Initial bio-compatibility assessments with human hepatocytes show that the acid functionality does not have any detrimental effect on cell adhesion. It is therefore believed that this material can be a useful precursor scaffold towards 3D substrates that offer tailored surface functionality for enhanced cell adhesion. PMID:24243821

  17. Multielement crystalline and pseudocrystalline oxides as efficient catalysts for the direct transformation of glycerol into acrylic acid.

    PubMed

    Chieregato, Alessandro; Soriano, M Dolores; García-González, Ester; Puglia, Giuseppe; Basile, Francesco; Concepción, Patricia; Bandinelli, Claudia; López Nieto, José M; Cavani, Fabrizio

    2015-01-01

    Glycerol surplus from biodiesel synthesis still represents a major problem in the biofuel production chain. Meanwhile, those in the acrylic acid market are looking for new processes that are able to offer viable alternatives to propylene-based production. Therefore, acrylic acid synthesis from glycerol could be an effective solution to both issues. Among the viable routes, one-pot synthesis theoretically represents the most efficient process, but it is also highly challenging from the catalyst design standpoint. A new class of complex W--Mo--V mixed-oxide catalysts, which are strongly related to the hexagonal tungsten bronze structure, able to directly convert glycerol into acrylic acid with yields of up to 51 % are reported. PMID:25488515

  18. Topological characterization of a bacterial cellulose-acrylic acid polymeric matrix.

    PubMed

    Halib, N; Mohd Amin, M C I; Ahmad, I; Abrami, M; Fiorentino, S; Farra, R; Grassi, G; Musiani, F; Lapasin, R; Grassi, M

    2014-10-01

    This paper focuses on the micro- and nano-topological organization of a hydrogel, constituted by a mixture of bacterial cellulose and acrylic acid, and intended for biomedical applications. The presence of acrylic acid promotes the formation of two interpenetrated continuous phases: the primary "pores phase" (PP) containing only water and the secondary "polymeric network phase" (PNP) constituted by the polymeric network swollen by the water. Low field Nuclear Magnetic Resonance (LF NMR), rheology, Scanning Electron Microscopy (SEM) and release tests were used to determine the characteristics of the two phases. In particular, we found that this system is a strong hydrogel constituted by 81% (v/v) of PP phase the remaining part being occupied by the PNP phase. Pores diameters span in the range 10-100 μm, the majority of them (85%) falling in the range 30-90 μm. The high PP phase tortuosity indicates that big pores are not directly connected to each other, but their connection is realized by a series of interconnected small pores that rend the drug path tortuous. The PNP is characterized by a polymer volume fraction around 0.73 while mesh size is around 3 nm. The theoretical interpretation of the experimental data coming from the techniques panel adopted, yielded to the micro- and nano-organization of our hydrogel. PMID:24932712

  19. Controlled release of anti-diabetic drug Gliclazide from poly(caprolactone)/poly(acrylic acid) hydrogels.

    PubMed

    Bajpai, S K; Chand, Navin; Soni, Shweta

    2015-01-01

    Drug Gliclazide (Glz) has limited solubility and low bioavailability. In order to obtain a controlled release of this drug and to improve its bioavailability, the drug has been loaded into poly(caprolactone) (PCL)/poly(acrylic acid) (PAAc) hydrogels, prepared by free radical polymerization of acrylic acid in the presence of poly(caprolactone) in acetone medium using azo-isobutyronitrile as initiator and N,N' methylene bisacrylamide as cross-linking agent. The swelling behaviour of these hydrogels has been investigated in the physiological gastric and intestinal fluids to obtain an optimum composition suitable for delivery of a biologically active compound. The gels were loaded with anti-diabetic drug Glz and a detailed investigation of release of drug has been carried out. Various kinetic models have been applied on the release data. Finally, the Albino wistar rats were treated for Streptozotocin plus nicotinamide - induced diabetes using a Glz-loaded PCL/PAAc hydrogel. The results indicated a fair reduction in the glucose level of rats. PMID:26135033

  20. Protein absorption and fouling on poly(acrylic acid)-graft-polypropylene microfiltration membrane

    NASA Astrophysics Data System (ADS)

    Liu, Yanjun; Ma, Huiying; Lv, Chunying; Yang, Jia; Fu, Xueqi

    2009-07-01

    A series of pH-sensitive poly (acrylic acid)-graft-polypropylene hollow fiber microfiltration membranes were prepared by UV-photo-irradiation. Bovine serum albumin (BSA) was chosen as the model protein to investigate its absorption and fouling behaviors on membranes. The results showed that the hydrophilicity of grafted membrane was improved by poly(acrylic acid) chains with parts of membrane pores blocked. The grafted membranes were markedly pH-dependent on the water permeability as pH was altered from 1 to 11. The zeta potential of grafted membranes calculated by streaming potential was negative in most pH range. Electrostatic interaction energy calculated by DLVO theory showed the electric interaction force between grafted membrane and BSA was attractive. With the rise of grafting degree, the electric attractive force between grafted membrane and BSA increased as pH=3 and decreased as pH=8, while it kept basically unchanged as pH=4.7. As a result, most serious fouling was observed as pH=4.7. Grafted membranes had a lower BSA absorption and better antifouling behavior as pH=8, while the opposite result was revealed as pH=3. In conclusion, the absorption and fouling behavior of BSA on membranes was pH-dependent due to the pH-dependence of membrane charge, and the conformation of BSA and grafting chains.

  1. Characterization of thin-film deposition in a pulsed acrylic acid polymerizing discharge

    SciTech Connect

    Voronin, Sergey A.; Bradley, James W.; Fotea, Catalin; Zelzer, Mischa; Alexander, Morgan R.

    2007-07-15

    In this study, thin-film deposition in a pulsed rf polymerizing discharge (13.56 MHz) struck in acrylic acid has been investigated by mass spectrometry, x-ray photoelectron spectroscopy, and quartz crystal microbalance techniques. The experiment was conducted at a fixed acrylic acid pressure of 1.3 Pa and 'on' pulse duration of 0.1 ms, whereas the 'off' time was varied between 0 and 20 ms. The rf input power in the 'on' time and gas flow rate were varied between 10 and 50 W and 1.5 and 4.8 sccm (sccm denotes cubic centimeter per minute at STP), respectively. These changes of the discharge conditions resulted in large-scale progressive variations in film and gas-phase plasma composition. In particular, the -COOH functionality of the monomer was increasingly retained in the plasma-generated thin films as the duty cycle was lowered (i.e., with lowered time-averaged powers). The monomer retention reached its maximum value of 66% for 'off' times exceeding 5 ms, when the discharge was operating in the power-deficient regime. The results show that the film deposition rate is a strong function of the monomer flow rate, whereas -COOH retention is correlated to the amount of unfragmented monomer in the plasma, controlled by the applied power.

  2. Precipitation-Redispersion of Cerium Oxide Nanoparticles with Poly(acrylic acid): Toward Stable Dispersions

    SciTech Connect

    Sehgal,A.; Lalatonne, Y.; Berret, J.; Morvan, M.

    2005-01-01

    We exploit a precipitation-redispersion mechanism for complexation of short chain polyelectrolytes with cerium oxide nanoparticles to extend their stability ranges. As synthesized, cerium oxide sols at pH 1.4 consist of monodisperse cationic nanocrystalline particles having a hydrodynamic diameter of 10 nm and a molecular weight of 400 000 g mol{sup -1}. We show that short chain uncharged poly(acrylic acid) at low pH when added to a cerium oxide sols leads to macroscopic precipitation. As the pH is increased, the solution spontaneously redisperses into a clear solution of single particles with an anionic poly(acrylic acid) corona. The structure and dynamics of cerium oxide nanosols and their hybrid polymer-inorganic complexes in solution are investigated by static and dynamic light scattering, X-ray scattering, and chemical analysis. Quantitative analysis of the redispersed sol gives rise to an estimate of 40-50 polymer chains per particle for stable suspension. This amount represents 20% of the mass of the polymer-nanoparticle complexes. This complexation adds utility to the otherwise unstable cerium oxide dispersions by extending the range of stability of the sols in terms of pH, ionic strength, and concentration.

  3. Spectroscopic and density functional theory studies of trans-3-(trans-4-imidazolyl)acrylic acid.

    PubMed

    Arjunan, V; Remya, P; Sathish, U; Rani, T; Mohan, S

    2014-08-14

    The structural parameters, thermodynamic properties and vibrational frequencies of the optimised geometry of trans-3-(trans-4-imidazolyl)acrylic acid have been determined from B3LYP methods with 6-311++G(**) and cc-pVTZ basis sets. The effects of substituents (acrylyl group) on the imidazole vibrational frequencies are analysed. The vibrational frequencies of the fundamental modes of trans-3-(trans-4-imidazolyl)acrylic acid have been precisely assigned and analysed and the theoretical results are compared with the experimental vibrations. (1)H and (13)C NMR isotropic chemical shifts are calculated and the assignments made are compared with the experimental values. The energies of important MO's of the compound are also determined from DFT method. The total electron density and electrostatic potential of the compound are determined by natural bond orbital analysis. Various reactivity and selectivity descriptors such as chemical hardness, chemical potential, softness, electrophilicity, nucleophilicity and the appropriate local quantities employing natural population analysis (NPA) are calculated. PMID:24755636

  4. Spectroscopic and density functional theory studies of trans-3-(trans-4-imidazolyl)acrylic acid

    NASA Astrophysics Data System (ADS)

    Arjunan, V.; Remya, P.; Sathish, U.; Rani, T.; Mohan, S.

    2014-08-01

    The structural parameters, thermodynamic properties and vibrational frequencies of the optimised geometry of trans-3-(trans-4-imidazolyl)acrylic acid have been determined from B3LYP methods with 6-311++G** and cc-pVTZ basis sets. The effects of substituents (acrylyl group) on the imidazole vibrational frequencies are analysed. The vibrational frequencies of the fundamental modes of trans-3-(trans-4-imidazolyl)acrylic acid have been precisely assigned and analysed and the theoretical results are compared with the experimental vibrations. 1H and 13C NMR isotropic chemical shifts are calculated and the assignments made are compared with the experimental values. The energies of important MO’s of the compound are also determined from DFT method. The total electron density and electrostatic potential of the compound are determined by natural bond orbital analysis. Various reactivity and selectivity descriptors such as chemical hardness, chemical potential, softness, electrophilicity, nucleophilicity and the appropriate local quantities employing natural population analysis (NPA) are calculated.

  5. ABS polymer electroless plating through a one-step poly(acrylic acid) covalent grafting.

    PubMed

    Garcia, Alexandre; Berthelot, Thomas; Viel, Pascal; Mesnage, Alice; Jégou, Pascale; Nekelson, Fabien; Roussel, Sébastien; Palacin, Serge

    2010-04-01

    A new, efficient, palladium- and chromium-free process for the electroless plating of acrylonitrile-butadiene-styrene (ABS) polymers has been developed. The process is based on the ion-exchange properties of poly(acrylic acid) (PAA) chemically grafted onto ABS via a simple and one-step method that prevents using classical surface conditioning. Hence, ABS electroless plating can be obtained in three steps, namely: (i) the grafting of PAA onto ABS, (ii) the copper Cu(0) seeding of the ABS surface, and (iii) the nickel or copper metallization using commercial-like electroless plating bath. IR, XPS, and SEM were used to characterize each step of the process, and the Cu loading was quantified by atomic absorption spectroscopy. This process successfully compares with the commercial one based on chromic acid etching and palladium-based seed layer, because the final metallic layer showed excellent adhesion with the ABS substrate. PMID:20361751

  6. Electron-beam induced RAFT-graft polymerization of poly(acrylic acid) onto PVDF

    NASA Astrophysics Data System (ADS)

    Grasselli, M.; Betz, N.

    2005-07-01

    This paper explores for the first time the post-radiation-induced-graft polymerization on solid substrate using reversible addition-fragmentation transfer (RAFT) mechanism. Radiation-induced graft polymerization onto polymers is a potentially interesting technique to create easily new materials from highly resistant polymers, e.g. surface graft polymerization of acrylic acid (AA) onto poly(vinylidene difluoride) (PVDF) improves its surface properties without losing its excellent mechanical properties. As a consequence of the radical nature of the polymerization processes it is difficult to control molecular weight of grafted chains, and therefore design and standardize the properties of the final product. RAFT polymerization is a suitable method to obtain monodisperse polymers. The ability of the RAFT agents to control the polymer chain length could be an interesting approach to improve the grafted polymers obtained by post-radiation-induced-graft polymerization technique. In this way, graft polymerization of AA onto electron-beam irradiated α-PVDF was performed using trithiocarbonic acid bis(1-phenylethyl) ester as a RAFT agent to control the radical polymerization. We studied several grafting parameters such as solvent, monomer concentration and grafting time in order to achieve a poly(acrylic acid) (PAA) layer onto PVDF surface. Acetic acid was found to be the best solvent for many reasons, as to drive graft polymerization mainly to the polymer surface, complete solubility and stability of all reactants. Hydrolysis of PAA chains was also studied in order to remove the trithiocarbonate functionality from the grafted polymer. A mild chemical condition was achieved in order to have thiol groups that were detected onto the modified PVDF by specific enzymatic reaction.

  7. Poly(acrylic acid)-grafted fluoropolymer films for highly sensitive fluorescent bioassays.

    PubMed

    Jung, Chan-Hee; Hwang, In-Tae; Kuk, In-Seol; Choi, Jae-Hak; Oh, Byung-Keun; Lee, Young-Moo

    2013-03-01

    In this study, a facile and effective method for the surface functionalization of inert fluoropolymer substrates using surface grafting was demonstrated for the preparation of a new platform for fluorescence-based bioassays. The surface of perfluorinated poly(ethylene-co-propylene) (FEP) films was functionalized using a 150 keV ion implantation, followed by the graft polymerization of acrylic acid, to generate a high density of carboxylic acid groups on the implanted surface. The resulting functionalized surface was investigated in terms of the surface density of carboxylic acid, wettability, chemical structure, surface morphology, and surface chemical composition. These results revealed that poly(acrylic acid) (PAA) was successfully grafted onto the implanted FEP surface and its relative amount depended on the fluence. To demonstrate the usefulness of this method for the fabrication of bioassays, the PAA-grafted FEP films were utilized for the immobilization of probe DNA for anthrax toxin, followed by hybridization with Cy3-labeled target DNA. Liver cancer-specific α-feto-protein (AFP) antigen was also immobilized on the PAA-grafted FEP films. Texas Red-labeled secondary antibody was reacted with AFP-specific primary antibody prebound to the AFP antigen using an immunoassay method. The results revealed that the fluorescence intensity clearly depended on the concentration of the target DNA hybridized to the probe DNA and the AFP antigen immobilized on the FEP films. The lowest detectable concentrations of the target DNA and the AFP antigen were 10 fg/mL and 10 pg/mL, respectively, with the FEP films prepared at a fluence of 3 × 10(14) ions/cm(2). PMID:23452270

  8. Decolourization performance in C. I. Vat Yellow 1 aqueous suspension using hydrophobically modified poly(acrylic acid).

    PubMed

    Chen, J; Chen, M C

    2011-01-01

    A series of hydrophobically modified poly(acrylic acid) (PAA), poly(2-phenoxyethyl acrylate-co-acrylic acid) (poly(PHEA-co-AA)), have been synthesized and characterized by Ubbelohde type viscometry, Nuclear Magnetic Resonance (1H NMR) spectrometry and Differential Scanning Calorimetry (DSC). The shear thinning Non-Newtonian fluid behavior of their aqueous solution and the dependence on pH and hydrophobic group contents were found through apparent viscosity and rheological property investigating. Decolourization performance in C. I. Vat Yellow 1 aqueous suspension was evaluated through visible absorbance data. Decolourization performance of hydrophobically associated polymer indicates two times better than that of PAA. The quantitative relationship was mainly studied. PMID:21866762

  9. Aggregation of poly(acrylic acid)-containing elastin-mimetic copolymers

    PubMed Central

    Paik, Bradford A.; Blanco, Marco A.; Jia, Xinqiao; Roberts, Christopher J.; Kiick, Kristi L.

    2015-01-01

    Polymer-peptide conjugates were produced via the copper-catalyzed alkyne-azide cycloaddition of poly(tert butyl acrylate) (PtBA) and elastin-like peptides. An azide-functionalized polymer was produced via atom-transfer radical polymerization (ATRP) followed by conversion of bromine end groups to azide groups. Subsequent reaction of the polymer with a bis-alkyne-functionalized, elastin-like peptide proceeded with high efficiency, yielding di- and tri-block conjugates, which after deprotection, yielded poly(acrylic acid) (PAA)-based diblock and triblock copolymers. These conjugates were solubilized in dimethyl formamide, and titration of phosphate buffered saline (PBS) induced aggregation. The presence of polydisperse spherical aggregates was confirmed by dynamic light scattering and transmission electron microscopy. Additionally, a coarse-grained molecular model was designed to reasonably capture inter- and intramolecular interactions for the conjugates and its precursors. This model was used to assess the effect of the different interacting molecular forces on the conformational thermodynamic stability of the copolymers. Our results indicated that the PAA’s ability to hydrogen-bond with both itself and the peptide is the main interaction for stabilizing the diblocks and triblocks and driving their self-assembly, while interactions between peptides are suggested to play only a minor role on the conformational and thermodynamic stability of the conjugates. PMID:25611563

  10. UV-induced graft polymerization of acrylic acid in the sub-micronchannels of oxidized PET track-etched membrane

    NASA Astrophysics Data System (ADS)

    Korolkov, Ilya V.; Mashentseva, Anastassiya A.; Güven, Olgun; Taltenov, Abzal A.

    2015-12-01

    In this article, we report on functionalization of track-etched membrane based on poly(ethylene terephthalate) (PET TeMs) oxidized by advanced oxidation systems and by grafting of acrylic acid using photochemical initiation technique for the purpose of increasing functionality thus expanding its practical application. Among advanced oxidation processes (H2O2/UV) system had been chosen to introduce maximum concentration of carboxylic acid groups. Benzophenone (BP) photo-initiator was first immobilized on the surfaces of cylindrical pores which were later filled with aq. acrylic acid solution. UV-irradiation from both sides of PET TeMs has led to the formation of grafted poly(acrylic acid) (PAA) chains inside the membrane sub-micronchannels. Effect of oxygen-rich surface of PET TeMs on BP adsorption and subsequent process of photo-induced graft polymerization of acrylic acid (AA) were studied by ESR. The surface of oxidized and AA grafted PET TeMs was characterized by UV-vis, ATR-FTIR, XPS spectroscopies and by SEM.

  11. Preparation and drug-loading properties of Fe3O4/Poly(styrene-co-acrylic acid) magnetic polymer nanocomposites

    NASA Astrophysics Data System (ADS)

    Lu, Wensheng; Shen, Yuhua; Xie, Anjian; Zhang, Weiqiang

    2013-11-01

    Fe3O4/poly(styrene-co-acrylic acid) magnetic polymer nanocomposites were synthesized by the dispersion polymerization method using styrene as hard monomer, acrylic acid as functional monomer, Fe3O4 nanoparticles modified with oleic acid as core, and poly(styrene-co-acrylic acid) as shell. Drug-loading properties of magnetic polymer nanocomposites with curcumin as a model drug were also studied. The results indicated that magnetic polymer nanocomposites with monodisperse were obtained, the particle size distribution was 50-120 nm, and the average size was about 100 nm. The contents of poly(styrene-co-acrylic acid) and Fe3O4 nanoparticles in magnetic polymer nanocomposites were 74% and 24.7%, respectively. The drug-loading capacity and entrapment efficiency were 2.5% and 44.4%, respectively. The saturation magnetization of magnetic polymer nanocomposites at 300 K was 20.2 emu/g without coercivity and remanence. The as-prepared magnetic polymer nanocomposites have not only lots of functional carboxyl groups but also stronger magnetic response, which might have potential applications in drug carrier and targeted drug release.

  12. Inhibition of AAC(6′)-Ib-Mediated Resistance to Amikacin in Acinetobacter baumannii by an Antisense Peptide-Conjugated 2′,4′-Bridged Nucleic Acid-NC-DNA Hybrid Oligomer

    PubMed Central

    Lopez, Christina; Arivett, Brock A.; Actis, Luis A.

    2015-01-01

    Multiresistant Acinetobacter baumannii, a common etiologic agent of severe nosocomial infections in compromised hosts, usually harbors aac(6′)-Ib. This gene specifies resistance to amikacin and other aminoglycosides, seriously limiting the effectiveness of these antibiotics. An antisense oligodeoxynucleotide (ODN4) that binds to a duplicated sequence on the aac(6′)-Ib mRNA, one of the copies overlapping the initiation codon, efficiently inhibited translation in vitro. An isosequential nuclease-resistant hybrid oligomer composed of 2′,4′-bridged nucleic acid-NC (BNANC) residues and deoxynucleotides (BNANC-DNA) conjugated to the permeabilizing peptide (RXR)4XB (“X” and “B” stand for 6-aminohexanoic acid and β-alanine, respectively) (CPPBD4) inhibited translation in vitro at the same levels observed in testing ODN4. Furthermore, CPPBD4 in combination with amikacin inhibited growth of a clinical A. baumannii strain harboring aac(6′)-Ib in liquid cultures, and when both compounds were used as combination therapy to treat infected Galleria mellonella organisms, survival was comparable to that seen with uninfected controls. PMID:26169414

  13. Cloning and DNA sequence analysis of an aac(3)-Vb gene from Serratia marcescens.

    PubMed Central

    Rather, P N; Mierzwa, R; Hare, R S; Miller, G H; Shaw, K J

    1992-01-01

    The AAC(3)-V resistance mechanism is characterized by high-level resistance to the aminoglycosides gentamicin, netilmicin, 2'-N-ethylnetilmicin, and 6'-N-ethylnetilmicin and moderate resistance levels to tobramycin. Serratia marcescens 82041944 contains an AA(3)-V resistance mechanism as determined from aminoglycoside resistance profiles. This strain, however, does not exhibit hybridization with a probe derived from the previously cloned aac(3)-Va gene, (R. Allmansberger, B. Bräu, and W. Piepersberg, Mol. Gen. Genet. 198:514-520, 1985). High-pressure liquid chromatography analysis of the acetylation products of sisomicin carried out by extracts of S. marcescens 82041944 have demonstrated the presence of an AAC(3) enzyme. We have cloned the gene encoding this acetyltransferase and have designated it aac(3)-Vb. Nucleotide sequence comparisons show that the aac(3)-Va and aac(3)-Vb genes are 72% identical. The predicted AAC(3)-Vb protein is 28,782 Da. Comparisons of the deduced amino acid sequences show 75% identity and 84% similarity between the AAC(3)-Va and AAC(3)-Vb proteins. The use of a DNA fragment internal to the aac(3)-Vb as a hybridization probe demonstrated that the aac(3)-Vb gene is very rare in clinical isolates possessing an AAC(3)-V mechanism. PMID:1444303

  14. Novel one-dimensional lanthanide acrylic acid complexes: an alternative chain constructed by hydrogen bonding

    SciTech Connect

    Li Hui . E-mail: lihui@bit.edu.cn; Hu Changwen

    2004-12-01

    Novel one-dimensional (1D) chains of three lanthanide complexes La(L{sup 1}){sub 3}(CH{sub 3}OH)].CH{sub 3}OH (L{sup 1}=(E)-3-(2-hydroxyl-phenyl)-acrylic acid) 1, La(L{sup 2}){sub 3}(H{sub 2}O){sub 2}].2.75H{sub 2}O (L{sup 2}=(E)-3-(3-hydroxyl-phenyl)-acrylic acid) 2, and La(L{sup 3}){sub 3}(CH{sub 3}OH){sub 2}(H{sub 2}O)].CH{sub 3}OH (L{sup 3}=(E)-3-(4-hydroxyl-phenyl)-acrylic acid) 3 are reported. The crystal structure data are as follows for 1: C{sub 29}H{sub 29}LaO{sub 11}, monoclinic, P2{sub 1}/n, a=15.4289(12)A, b=7.9585(6)A, c=23.041(2)A, {beta}=99.657(2){sup o}, Z=4, R{sub 1}=0.0637, wR{sub 2}=0.0919; for 2: C{sub 27}H{sub 30.50}LaO{sub 13.75}, triclinic, P-1, a=8.4719(17)A, b=13.719(3)A, c=14.570(3)A, {alpha}=62.19(3){sup o}, {beta}=99.657(2){sup o}, {gamma}=78.22(3){sup o}, Z=2, R{sub 1}=0.0384, wR{sub 2}=0.0820; and for 3: C{sub 30}H{sub 35}LaO{sub 13}, monoclinic, P2(1)/c, a=9.5667(6)A, b=24.3911(15)A, c=14.0448(9)A, {beta}=109.245(2){sup o}, Z=4, R{sub 1}=0.0374, wR{sub 2}=0.0630. All the three structure data were collected using graphite monochromated molybdenum K{alpha} radiation and refined using full-matrix least-squares techniques on F{sup 2}. These structures show that four kinds of the carboxylato bridge modes are included in these chains to link the La(III) ions. It is the first time that it has been found that the intra-chain hydrogen bonding can construct an alternative chain even, when the coordination bridge mode is the same along the chain (complex 2). There are 2D and 3D hydrogen bonding in the crystal lattices of complexes 1-3.

  15. Pulsed and continuous wave acrylic acid radio frequency plasma deposits: plasma and surface chemistry.

    PubMed

    Voronin, Sergey A; Zelzer, Mischa; Fotea, Catalin; Alexander, Morgan R; Bradley, James W

    2007-04-01

    Plasma polymers have been formed from acrylic acid using a pulsed power source. An on-pulse duration of 100 micros was used with a range of discharge off-times between 0 (continuous wave) and 20,000 micros. X-ray photoelectron spectroscopy (XPS) has been used in combination with trifluoroethanol (TFE) derivatization to quantify the surface concentration of the carboxylic acid functionality in the deposit. Retention of this functionality from the monomer varied from 2% to 65%. When input power was expressed as the time-averaged energy per monomer molecule, E(mean), the deposit chemistry achieved could be described using a single relationship for all deposition conditions. Deposition rates were monitored using a quartz crystal microbalance, which revealed a range from 20 to 200 microg m(-2) s(-1), and these fell as COOH functional retention increased. The flow rate was found to be the major determinant of the deposition rate, rather than being uniquely defined by E(mean), connected to the rate at which fresh monomer enters the system in the monomer deficient regime. The neutral species were collected in a time-averaged manner. As the energy delivered per molecule in the system (E(mean)) decreased, the amount of intact monomer increased, with the average neutral mass approaching 72 amu as E(mean) tends to zero. No neutral oligomeric species were detected. Langmuir probes have been used to determine the temporal evolution of the density and temperature of the electrons in the plasma and the plasma potential adjacent to the depositing film. It has been found that even 500 micros into the afterglow period that ionic densities are still significant, 5-10% of the on-time density, and that ion accelerating sheath potentials fall from 40 V in the on-time to a few volts in the off-time. We have made the first detailed, time- and energy-resolved mass spectrometry measurements in depositing acrylic acid plasma. These have allowed us to identify and quantify the positive ion

  16. Ex vivo bioadhesion and in vivo testosterone bioavailability study of different bioadhesive formulations based on starch-g-poly(acrylic acid) copolymers and starch/poly(acrylic acid) mixtures.

    PubMed

    Ameye, D; Voorspoels, J; Foreman, P; Tsai, J; Richardson, P; Geresh, S; Remon, J P

    2002-02-19

    Starch-g-poly(acrylic acid) copolymers or grafted starches synthesized by 60Co irradiation or chemical modification and co-freeze-dried starch/poly(acrylic acid) mixtures were evaluated on their ex vivo bioadhesion capacity. The buccal absorption of testosterone from a bioadhesive tablet formulated with the grafted starches or starch/poly(acrylic acid) mixtures was investigated. The results were compared to a reference formulation (physical mixture of 5% Carbopol 974P and 95% Drum Dried Waxy Maize). Rice starch-based irradiated grafted starches showed the best bioadhesion results. Partial neutralization of the acrylic acid with Ca(2+) ions resulted in significantly higher bioadhesion values compared to the reference. Ca(2+) and Mg(2+) partially neutralized maltodextrin-based irradiated grafted starches showed significantly higher bioadhesion values compared to the reference formulation. The chemically modified grafted starches showed significantly higher adhesion force values than for the reference tablet. None of the co-freeze-dried starch/poly(acrylic acid) mixtures showed significantly higher bioadhesion results than the reference (Bonferroni test, P<0.05). A chemically modified grafted starch could sustain the 3 ng/ml plasma testosterone target concentration during +/- 8 h (T(>3 ng/ml)). By lyophilization of a partially neutralized irradiated grafted starch, the in vivo adhesion time (22.0 +/- 7.2 h) and the T(>3 ng/ml) (13.5 +/- 1.3 h) could be increased. The absolute bioavailability of the lyophilized formulation approached the reference formulation. Some of the grafted starches showed to be promising buccal bioadhesive drug carriers for systemic delivery. PMID:11853929

  17. A stencil printed, high energy density silver oxide battery using a novel photopolymerizable poly(acrylic acid) separator.

    PubMed

    Braam, Kyle; Subramanian, Vivek

    2015-01-27

    A novel photopolymerized poly(acrylic acid) separator is demonstrated in a printed, high-energy-density silver oxide battery. The printed battery demonstrates a high capacity of 5.4 mA h cm(-2) at a discharge current density of 2.75 mA cm(-2) (C/2 rate) while delivering good mechanical flexibility and robustness. PMID:25475759

  18. Properties of amylose-oleic acid inclusion complexes from corn starch grafted with poly(methyl acrylate)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Corn starch granules have been previously investigated as fillers in polymers. In this study, much smaller particles in the form of spherulites produced by steam jet-cooking high-amylose corn starch and oleic acid to form amylose inclusion complexes were graft polymerized with methyl acrylate, both ...

  19. Structure-function properties of amylose-oleic acid inclusion complexes grafted with poly(methyl acrylate)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Spherulites, produced by steam jet-cooking high-amylose starch and oleic acid, were grafted with methyl acrylate, both before and after removal of un-complexed amylopectin. For comparison, granular high-amylose corn starch was graft polymerized in a similar manner. The amount of grafted and ungrafte...

  20. REACTIVITIES OF ACRYLIC AND METHACRYLIC ACIDS IN A NUCLEOPHILIC ADDITION MODEL OF THEIR BIOLOGICAL ACTIVITY (JOURNAL VERSION)

    EPA Science Inventory

    The reactivities of derivatives of acrylic and methacrylic acid (AA and MAA) in Michael reactions of nucleophilic addition that have been proposed as the underlying mechanisms for the toxicity of such compounds are evaluated from a study of the mechanism of addition of a nucleoph...

  1. A facile one pot strategy for the synthesis of well-defined polyacrylates from acrylic acid via RAFT polymerization.

    PubMed

    Li, Qianbiao; Wang, Taisheng; Dai, Jingwen; Ma, Chao; Jin, Bangkun; Bai, Ruke

    2014-03-28

    A facile one pot strategy for the preparation of linear and hyperbranched polyacrylates has been successfully developed by the combination of in situ esterification of acrylic acid with halogenated compounds promoted by 1,1,3,3-tetramethylguanidine (TMG) and RAFT polymerization. PMID:24534953

  2. Introduction of poly[(2-acryloyloxyethyl trimethyl ammonium chloride)-co-(acrylic acid)] branches onto starch for cotton warp sizing.

    PubMed

    Shen, Shiqi; Zhu, Zhifeng; Liu, Fengdan

    2016-03-15

    An attempt has been made to reveal the effect of amphoteric poly(2-acryloyloxyethyl trimethyl ammonium chloride-co-acrylic acid) [P(ATAC-co-AA)] branches grafted onto the backbones of starch upon the adhesion-to-cotton, film properties, and desizability of maize starch for cotton warp sizing. Starch-g-poly[(2-acryloyloxyethyl trimethyl ammonium chloride)-co-(acrylic acid) [S-g-P(ATAC-co-AA)] was prepared by the graft copolymerization of 2-acryloyloxyethyl trimethyl ammonium chloride (ATAC) and acrylic acid (AA) with acid-converted starch (ACS) in aqueous medium using Fe(2+)-H2O2 initiator. The adhesion was evaluated in term of bonding strength according to the FZ/T 15001-2008 whereas the film properties considered included tensile strength, work and percentage elongation at break. The evaluation was undertaken through the comparison of S-g-P(ATAC-co-AA) with ACS, starch-g-poly(acrylic acid), and starch-g-poly(2-acryloyloxyethyl trimethyl ammonium chloride). It was found that the amphoteric branch was able to significantly improve the adhesion and mitigate the brittleness of starch film. Zeta potential of cooked S-g-P(ATAC-co-AA) paste, depending on the mole ratio of ATAC to AA units on P(ATAC-co-AA) branches, had substantial effect on the adhesion and desizability. Increasing the mole ratio raised the potential, which favored the adhesion but disfavored the removal of S-g-P(ATAC-co-AA) from sized cotton warps. Electroneutral S-g-P(ATAC-co-AA) was superior to negatively grafted starch in adhesion and to positively grafted starch in desizability. Generally, it showed better sizing property than ACS, starch-g-poly(acrylic acid), and starch-g-poly(2-acryloyloxyethyl trimethyl ammonium chloride), and had potential in the application of cotton warp sizing. PMID:26794764

  3. Terpolymers of ethyl acrylate/methacrylic acid/unsaturated acid ester of alcohols and acids as anti-settling agents in coal water slurries

    SciTech Connect

    Savoly, A.; Villa, J.L.; Grinstein, R.H.; Nachfolger, S.J.

    1988-05-17

    This patent describes a pumpable stabilized coal water slurry, having a coal content of at least about 50% by weight wherein at least 80% of the coal particles are about 200 mesh or finer, containing from about 0.01% to about 1% by weight of the slurry of a water soluble terpolymer of ethylacrylate (A), metacrylic acid (B) and a third monomer (C) selected from the group consisting of an unsaturated carboxylic acid ester of an alcohol and an ethoxylated carboxylic acid. The unsaturated carboxylic acid is a mono- or di- basic unsaturated carboxylic acid of 3 to 10 carbon atoms selected from the group consisting of acrylic acid, methacrylic acid, itaconic acid, fumaric acid, and maleic acid.

  4. Cascade enzymatic catalysis in poly(acrylic acid) brushes-nanospherical silica for glucose detection.

    PubMed

    Zhao, Yan; Wang, Ying; Zhang, Xiaobin; Kong, Rongmei; Xia, Lian; Qu, Fengli

    2016-08-01

    The ultrasensitive monitoring of glucose with a fast and accurate method is significant in potential therapeutics and optimizes protein biosynthesis. Incorporation of enzyme into matrix is considered as promising candidates for constructing highly sensitive glucose-responsive systems. In this study, three-dimensional poly(acrylic acid) brushes-nanospherical silica (PAA-nano silica) with high amplification capability and stability were used to covalently immobilize bienzymes for cascade enzymatic catalysis. The major advantages of PAA-nano silica-bienzyme co-incorporation is that the enzymes are proximity distribution, and such close confinement both minimized the diffusion of intermediates among the enzymes in the consecutive reaction and improve the utilization efficiency of enzymes, thereby enhancing the overall reaction efficiency and specificity. Thus, this present bienzymatic biosensor shows robust signal amplification and ultrasensitivity of glucose-responsive properties with a detection limit of 0.04μM. PMID:27216683

  5. SYNTHESIS AND CHARACTERIZATION OF SUBSTITUTED POLY(STYRENE)-b-POLY(ACRYLIC ACID) BLOCK COPOLYMER MICELLES

    SciTech Connect

    Pickel, Deanna L; Pickel, Joseph M; Devenyi, Jozsef; Britt, Phillip F

    2009-01-01

    Block copolymer micelle synthesis and characterization has been extensively studied. In particular, most studies have focused on the properties of the hydrophilic corona due to the micelle corona structure s impact on the biodistribution and biocompatibility. Unfortunately, less attention has been given to the effect of the core block on the micelle stability, morphology, and the rate of diffusion of small molecules from the core. This investigation is focused on the synthesis of block copolymers composed of meta-substituted styrenes and acrylic acid by Atom Transfer Radical Polymerization. Micelles with cores composed of substituted styrenes having Tgs ranging from -30 to 100 oC have been prepared and the size and shape of these micelles were characterized by Static and Dynamic Light Scattering and TEM. In addition, the critical micelle concentration and rate of diffusion of small molecules from the core were determined by fluorimetry using pyrene as the probe.

  6. Amylopectin grafted with poly (acrylic acid): development and application of a high performance flocculant.

    PubMed

    Sarkar, Amit Kumar; Mandre, N R; Panda, A B; Pal, Sagar

    2013-06-20

    In recent years, wastewater treatment, especially for wastewaters which are not suitably recycled by conventional or normal biological processes, is getting more importance. Of late, natural biopolymer based flocculants are extensively used for wastewater treatment because of low cost, environment-friendly and easily availablility from reproducible farm and forest resources. This article introduces the development of a natural polymer based flocculant [amylopectin grafted with poly (acrylic acid) - AP-g-PAA] for treatment of synthetic effluent as well as mining industry wastewater. The graft copolymer based flocculants have been developed under optimum conditions and characterized using viscometry, (13)C NMR, SEM, TGA, rheological characteristics, determination of hydrodynamic radius and CHN analysis. The flocculation characteristics of grafted and ungrafted polysaccharide have been evaluated in synthetic effluents (as Fe-ore, kaolin, Mn ore suspensions) as well as in mining industry wastewater. PMID:23648038

  7. Electrophoretic Mobility of Poly(acrylic acid)-Coated Alumina Particles

    SciTech Connect

    Bhosale, Prasad S.; Chun, Jaehun; Berg, John C.

    2011-06-01

    The effect of poly (acrylic acid) (PAA) adsorption on the electrokinetic behavior of alumina dispersions under high pH conditions was investigated as a function of polymer concentration and molecular weight as well as the presence, concentration and ion type of background electrolyte. Systems of this type are relevant to nuclear waste treatment, in which PAA is known to be an effective rheology modifier. The presence of all but the lowest molecular weight PAA studied (1800) led to decreases in dynamic electrophoretic mobility at low polymer concentrations, attributable to bridging flocculation, as verified by measurements of particle size distribution. Bridging effects increased with polymer molecular weight, and decreased with polymer concentration. Increases in background electrolyte concentration enhanced dynamic electrophoretic mobility as the polymer layers were compressed and bridging was reduced. Such enhancements were reduced as the cation was changed from Na+ to K+ to Cs+.

  8. Study on swelling behaviour of hydrogel based on acrylic acid and pectin from dragon fruit

    NASA Astrophysics Data System (ADS)

    Abdullah, Mohd Fadzlanor; Lazim, Azwani Mat

    2014-09-01

    Biocompatible hydrogel based on acrylic acid (AA) and pectin was synthesized using gamma irradiation technique. AA was grafted onto pectin backbone that was extracted from dragon fruit under pH 3.5 and extracts and ethanol ratios (ER) 1:0.5. The optimum hydrogel system with high swelling capacity was obtained by varying the dose of radiation and ratio of pectin:AA. FTIR-ATR spectroscopy was used to verify the interaction while thermal properties were analyzed by TGA and DSC. Swelling studies was carried out in aqueous solutions with different pH values as to determine the pH sensitivity. The results show that the hydrogel with a ratio of 2:3 (pectin:AA) and 30 kGy radiation dose has the highest swelling properties at pH of 10.

  9. Water dispersible polytetrafluoroethylene microparticles prepared by grafting of poly(acrylic acid)

    NASA Astrophysics Data System (ADS)

    Yang, Changqiao; Xu, Lu; Zeng, Hongyan; Tang, Zhongfeng; Zhong, Lei; Wu, Guozhong

    2014-10-01

    Due to the hydrophobic nature and high gravimetric density, it is very difficult to obtain water dispersible polytetrafluoroethylene (PTFE) powder. In this work, hydrophilic PTFE microparticles were successfully prepared by grafting of poly(acrylic acid) onto PTFE micropowder via a pre-irradiation method. The as-obtained hydrophilic PTFE microparticles were analyzed by FT-IR, 1H NMR, CA, SEM and TGA. After neutralization by sodium hydroxide, the water contact angle decreased from 145.69° for pristine PTFE to 63.38° for PTFE-g-NaAA. The obtained micropowder can be easily dispersed in water to form a dispersion with very high stability. Furthermore, the presence of grafted PAA shows no obvious influence on degradation temperature of PTFE backbones.

  10. Scaffolds of Hyaluronic Acid-Poly(Ethyl Acrylate) Interpenetrating Networks: Characterization and In Vitro Studies.

    PubMed

    Rodríguez-Pérez, E; Lloret Compañ, A; Monleón Pradas, M; Martínez-Ramos, C

    2016-08-01

    Hyaluronic acid (HA) provides many advantages to regenerative implants through its bioactive properties, but it also has many limitations as a biomaterial if it is not chemically modified. In order to overcome some of these limitations, HA has been combined with poly(ethyl acrylate) in the form of interpenetrating polymeric networks (IPNs), in which the HA network is crosslinked with divinyl sulfone. Scaffolds of this IPN have been produced through a template-leaching methodology, and their properties have been compared with those of single-network scaffolds made of either PEA or crosslinked HA. A fibroblast cell line has been used to assess the in vitro performance of the scaffolds, revealing good cell response and a differentiated behavior on the IPN surface when compared to the individual polymers. Altogether, the results confirm that this type of material offers an interesting microenvironment for cells, which can be further improved toward its potential use in medical implants. PMID:27072058

  11. Acrylic acid grafted guargum-nanosilica membranes for transdermal diclofenac delivery.

    PubMed

    Giri, Arindam; Bhunia, Tridib; Mishra, Samir Ranjan; Goswami, Luna; Panda, Asit Baran; Pal, Sagar; Bandyopadhyay, Abhijit

    2013-01-16

    Green, hydrophobic device for controlled transdermal release of diclofenac sodium was designed from in situ nanosilica/acrylic acid grafted guargum membranes. Best grafting condition was assigned and nanocomposites were formed in situ using varying proportions of aqueous nanosilica sol. Nanocomposite/drug conjugates were formed by bringing down the medium pH from 9.0 to 7.0. The conjugates were characterized through infrared and solid state NMR spectroscopy, electron microscopy, hydro-swelling, surface contact angle, viscometry and biocompatibility. Most balanced property was exhibited by the membrane containing 1wt% nanosilica. It also had shown the highest encapsulation efficacy vis-à-vis slowest release as compared to others during experimentation in a Franz diffusion cell. PMID:23121937

  12. Surface Modification of PET Fabric by Graft Copolymerization with Acrylic Acid and Its Antibacterial Properties

    PubMed Central

    Abdolahifard, M.; Bahrami, S. Hajir; Malek, R. M. A.

    2011-01-01

    Graft copolymerization of acrylic acid (AA) onto Poly(ethylene terephthalate) (PET) fabrics with the aid of benzoyl peroxide was carried out. The effect of polymerization parameters on the graft yield was studied. Percent grafting was enhanced significantly by increasing benzoyl peroxide (BP) concentrations up to 3.84 g/lit and then decreased upon further increase in initiator concentration. Preswelling of PET leads to changes in its sorption-diffusion properties and favors an increase in the degree of grafting. The antibiotics treated grafted fabrics showed antibacterial properties towards gram-positive and gram-negative microorganisms. FTIR and SEM were used to characterize AA-grafted polyester fabrics. PMID:24052819

  13. Characterization of new acrylic bone cements prepared with oleic acid derivatives.

    PubMed

    Vázquez, Blanca; Deb, Sanjukta; Bonfield, William; Román, Julio San

    2002-01-01

    Acrylic bone-cement formulations were prepared with the use of a new tertiary aromatic amine derived from oleic acid, and also by incorporating an acrylic monomer derived from the same acid with the aim of reducing the leaching of toxic residuals and improving mechanical properties. 4-N,N dimethylaminobenzyl oleate (DMAO) was used as an activator in the benzoyl-peroxide radical cold curing of polymethyl methacrylate. Cements that contained DMAO exhibited much lower polymerization exotherm values, ranging between 55 and 62 C, with a setting time around 16--17 min, depending on the amine/BPO molar ratio of the formulation. On curing a commercial bone cement, Palacosreg R with DMAO, a decrease of 20 C in peak temperature and an increase in setting time of 7 min were obtained, the curing parameters remaining well within limits permitted by the standards. In a second stage, partial substitution of MMA by oleyloxyethyl methacrylate (OMA) in the acrylic formulations was performed, the polymerization being initiated with the DMAO/BPO redox system. These formulations exhibited longer setting times and lower peak temperatures with respect to those based on PMMA. The glass transition temperature of the experimental cements were lower than that of PMMA cement because of the presence of long aliphatic chains of both activator and monomer in the cement matrix. Number average molecular weights of the cured cements were in the range of 1.2x10(5). PMMA cements cured with DMAO/BPO revealed a significant (p<0.001) increase in the strain to failure and a significant (p<0.001) decrease in Young's modulus in comparison to Palacosreg R, whereas ultimate tensile strength remained unchanged. When the monomer OMA was incorporated, low concentrations of OMA provided a significant increase in tensile strength and elastic modulus without impairing the strain to failure. The results demonstrate that the experimental cements based on DMAO and OMA have excellent promise for use as orthopaedic and

  14. AAC Modeling Intervention Research Review

    ERIC Educational Resources Information Center

    Sennott, Samuel C.; Light, Janice C.; McNaughton, David

    2016-01-01

    A systematic review of research on the effects of interventions that include communication partner modeling of aided augmentative and alternative communication (AAC) on the language acquisition of individuals with complex communication needs was conducted. Included studies incorporated AAC modeling as a primary component of the intervention,…

  15. Corrosion Inhibitive Evaluation of an Environmentally Friendly Water-Base Acrylic Terpolymer on Mild Steel in Hydrochloric Acid Media

    NASA Astrophysics Data System (ADS)

    Azghandi, Mojtaba Vakili; Davoodi, Ali; Farzi, Gholam Ali; Kosari, Ali

    2013-12-01

    The corrosion inhibitive performance of an environmentally friendly water-base acrylic terpolymer [methyl methacrylate/Butyl Acrylate/Acrylic acid (ATP)] on mild steel in 1 M HCl was investigated by alternating current and direct current electrochemical techniques and the quantum chemical method. An efficiency of more than 97 pct was obtained with 0.8 mmol/L ATP. The increase in inhibitor concentration and immersion time has a positive effect, while the temperature influence is negligible on the inhibitor efficiency. The present terpolymer obeys the Langmuir isotherm, and thermodynamic calculation reveals a chemisorption type on the surface. Density functional calculations showed that the lone pairs of electrons of oxygen in the structure of three monomers are suitable sites to adsorb onto the metal surface. Finally, in the presence of ATP, a decrease in surface roughness and corrosion attacks was demonstrated by atomic force microscopy and optical microscopy examinations, respectively.

  16. Thiomers: Influence of molecular mass and thiol group content of poly(acrylic acid) on efflux pump inhibition.

    PubMed

    Grabovac, Vjera; Laffleur, Flavia; Bernkop-Schnürch, Andreas

    2015-09-30

    The aim of the present study was to investigate the influence of molecular mass and thiol group content of poly(acrylic acid)-cysteine conjugates on the permeation of sulforhodamine 101 and penicillin G. acting as substrates for multidrug resistance-associated protein 2 efflux pump. Poly(acrylic acids) of 2 kDa, 100 kDa, 250 kDa, 450 kDa and 3000 kDa were conjugated with cysteine. The thiol group content of all these polymers was in the range from 343.3 ± 48.4 μmol/g to 450.3 ± 76.1 μmol/g. Transport studies were performed on rat small intestine mounted in Ussing-type chambers. Since 250 kDa poly(acrylic acid) showed the highest permeation enhancing effect, additionally thiolated 250 kDa polyacrylates displaying 157.2 μmol/g, 223.0 ± 18.1 and 355.9 μmol/g thiol groups were synthesized in order to investigate the influence of thiol group content on the permeation enhancement. The permeation of sulforhodamine was 3.93- and 3.85-fold improved using 250 kDa poly(acrylic acid)-cysteine conjugate exhibiting 355.9 ± 39.5 μmol/g and 223.0 ± 18.1 μmol/g thiol groups. Using the same conjugates the permeation of penicillin G was 1.70- and 1.59-fold improved, respectively. The study demonstrates that thiolated poly(acrylic acid) inhibits Mrp2 mediated transport and that the extent of inhibition depends on the molecular mass and degree of thiolation of the polymer. PMID:26238816

  17. Controlled release of insulin through hydrogels of (acrylic acid)/trimethylolpropane triacrylate

    NASA Astrophysics Data System (ADS)

    Raymundi, Vanessa C.; Aguiar, Leandro G.; Souza, Esmar F.; Sato, Ana C.; Giudici, Reinaldo

    2015-12-01

    Hydrogels of poly(acrylic acid) crosslinked with trimethylolpropane triacrylate (TMPTA) were produced through solution polymerization. After these hydrogels were loaded with insulin solution, they evidenced swelling. Experiments of controlled release of insulin through the hydrogels were performed in acidic and basic media in order to evaluate the rates of release of this protein provided by the referred copolymer. Additionally, a mathematical description of the system based on differential mass balance was made and simulated in MATLAB. The model consists of a system of differential equations which was solved numerically. As expected, the values of swelling index at the equilibrium and the rates of insulin release were inversely proportional to the degree of crosslinking. The mathematical model provided reliable predictions of release profiles with fitted values of diffusivity of insulin through the hydrogels in the range of 6.0 × 10-7-1.3 × 10-6 cm2/s. The fitted and experimental values of partition coefficients of insulin between the hydrogel and the medium were lower for basic media, pointing out good affinity of insulin for these media in comparison to the acidic solutions.

  18. pH-Responsive Behavior of Poly(acrylic acid) Brushes of Varying Thickness

    NASA Astrophysics Data System (ADS)

    Yadav, Vivek; Robertson, Megan; Conrad, Jacinta

    2015-03-01

    We have investigated the pH-dependent response of polyelectrolyte brushes of varying thickness. Our model system consists of poly(acrylic acid) brushes, which change from hydrophobic and neutral at low pH to hydrophilic and negatively charged at high pH, synthesized using a grafting-from approach at constant grafting density. As the polymer brush thickness increased, the brushes exhibited greater hysteresis in static water contact angle as a function of pH. We extracted the pKa of the polymer brushes from contact angle measurements. The relationship between the pKa and brush thickness depended on the order in which the brushes were exposed to solutions of varying pH: pKa decreased on increasing brush thickness when going from basic to acidic medium whereas pKa increased on increasing brush thickness when going from acidic to basic medium. We speculate that the origin of hysteresis can be explained by pH-dependent conformational changes in these polyelectrolyte brushes.

  19. Polyaniline/poly acid acrylic thin film composites: a new gamma radiation detector

    SciTech Connect

    Lima Pacheco, Ana P.; Araujo, Elmo S.; Azevedo, Walter M. de

    2003-03-15

    In this paper, we present a new and straightforward route to prepare polyaniline/poly acid acrylic (PAA) thin film composites in large areas and on almost any surface. This method was developed to improve the mechanical and adherence properties of polyaniline devices used as ionization radiation sensors. The route consists of the combination of the metal oxidant with polymer acid to form a highly homogeneous and viscous paste, which can be easily spread over any surface. In the second step, an aniline acid solution is brought in contact with the dried paste where polymerization occurs, yielding a high homogeneous and conducting polymer composite. The UV-visible absorption and infrared analysis confirm that a polyaniline/PAA complex is obtained. The four-point conductivity measurements show that the composite conductivity {rho} is the order of 5 {omega}{sup -1} cm{sup -1}. Preliminary gamma radiation interaction with the composite shows that the doped composite exhibits a linear response that can be used in the development of real-time radiation sensors for the dose range from 0 to 5000 Gy.

  20. The effect of unsaturated fatty acid and triglyceride oil addition on the mechanical and antibacterial properties of acrylic bone cements.

    PubMed

    Persson, Cecilia; Robert, Elise; Carlsson, Elin; Robo, Céline; López, Alejandro; Godoy-Gallardo, Maria; Ginebra, Maria-Pau; Engqvist, Håkan

    2015-09-01

    Acrylic bone cements have an elastic modulus several times higher than the surrounding trabecular bone. This has been hypothesized to contribute to certain clinical complications. There are indications that the addition of specific fatty acids and triglyceride oils may reduce the elastic modulus of these types of cements. Some of these additives also appear to have inherent antibiotic properties, although this has never been evaluated in bone cements. In this study, several types of fatty acids and triglyceride oils were evaluated for use in acrylic bone cements. Their mechanical properties were evaluated under uniaxial compression testing and selected cements were then further characterized in terms of microstructure, handling and antibacterial properties using scanning electron microscopy, polymerization temperature measurements, agar diffusion tests and bactericidal activity assays of cement extracts. It was found that any of the evaluated fatty acids or triglyceride oils could be used to tailor the stiffness of acrylic bone cements, although at varying concentrations, which also depended on the type of commercial base cement used. In particular, the addition of very small amounts of linoleic acid (<2.0 wt%) resulted in Young's moduli and compressive strengths in the range of human trabecular bone, while maintaining a similar setting time. Further, the addition of 12.6 wt% ricinoleic acid to Osteopal V cement was found to have a significant antibacterial effect, inhibiting growth of Staphylococcus aureus in an agar diffusion test as well as demonstrating 100% bactericidal activity against the same strain. PMID:25876889

  1. Synthesis of poly acrylic acid modified silver nanoparticles and their antimicrobial activities.

    PubMed

    Ni, Zhihui; Wang, Zhihua; Sun, Lei; Li, Binjie; Zhao, Yanbao

    2014-08-01

    Poly acrylic acid modified silver (Ag/PAA) nanoparticles (NPs) have been successfully synthesized in the aqueous solution by using tannic acid as a reductant. The structure, morphology and composition of Ag/PAA NPs were characterized by various techniques such as X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible absorption spectroscopy (UV-vis) and thermogravimetry analysis (TGA). The results show that PAA/Ag NPs have a quasi-ball shape with an average diameter of 10 nm and exhibit well crystalline, and the reaction conditions have some effect on products morphology and size distribution. In addition, the as-synthesized Ag/PAA NPs antimicrobial activities against Escherichia coli (E. coli), Pseudomonas aeruginosa (P. aeruginosa) and Staphylococcus aureus (S. aureus) were evaluated by the methods of broth dilution, cup diffusion, optical density (OD600) and electron microscopy observation. The as-synthesized Ag/PAA NPs exhibit excellent antibacterial activity. The antimicrobial mechanism may be attributed to the damaging of bacterial cell membrane and causing leakage of cytoplasm. PMID:24907758

  2. Homo- and co-polymerization of polysytrene-block-poly(acrylic acid)-coated metal nanoparticles.

    PubMed

    Wang, Hong; Song, Xiaohui; Liu, Cuicui; He, Jiating; Chong, Wen Han; Chen, Hongyu

    2014-08-26

    Amphiphilic block copolymers such as polystyrene-block-poly(acrylic acid) (PSPAA) give micelles that are known to undergo sphere-to-cylinder shape transformation. Exploiting this polymer property, core-shell nanoparticles coated in PSPAA can be "polymerized" into long chains following the chain-growth polymerization mode. This method is now extended to include a variety of different nanoparticles. A case study on the assembly process was carried out to understand the influence of the PAA block length, the surface ligand, and the size and morphology of the monomer nanoparticles. Shortening the PAA block promotes the reorganization of the amphiphilic copolymer in the micelles, which is essential for assembling large Au nanoparticles. Small Au nanoparticles can be directly "copolymerized" with empty PSPAA micelles into chains. The reaction time, acid quantity, and the [Au nanoparticles]/[PSPAA micelles] concentration ratio played important roles in controlling the sphere-cylinder-vesicle conversion of the PSPAA micelles, giving rise to different kinds of random "copolymers". With this knowledge, a general method is then developed to synthesize homo, random, and block "copolymers", where the basic units include small Au nanoparticles (d = 16 nm), large Au nanoparticles (d = 32 nm), Au nanorods, Te nanowires, and carbon nanotubes. Given the lack of means for assembling nanoparticles, advancing synthetic capabilities is of crucial importance. Our work provides convenient routes for combining nanoparticles into long-chain structures, facilitating rational design of complex nanostructures in the future. PMID:25000121

  3. Nanoparticle Formation from Hybrid, Multiblock Copolymers of Poly(Acrylic Acid) and VPGVG Peptide

    PubMed Central

    Grieshaber, Sarah E.; Paik, Bradford A.; Bai, Shi; Kiick, Kristi L.; Jia, Xinqiao

    2012-01-01

    Elastin-mimetic hybrid copolymers with an alternating molecular architecture were synthesized via the step growth polymerization of azide-functionalized, telechelic poly(tert-butyl acrylate) (PtBA) and an alkyne-terminated, valine and glycine-rich peptide with a sequence of (VPGVG)2 (VG2). The resultant hybrid copolymer, [PtBA-VG2]n, contains up to six constituent building blocks and has a polydispersity index (PDI) of ~1.9. Trifluoroacetic acid (TFA) treatment of [PtBA-VG2]n gave rise to an alternating copolymer of poly(acrylic acid) (PAA) and VG2 ([PAA-VG2]n). The modular design permits facile adjustment of the copolymer composition by varying the molecular weight of PAA (22 and 63 repeat units). Characterization by dynamic light scattering indicated that the multiblock copolymers formed discrete nanoparticles at room temperature in aqueous solution at pH 3.8, with an average diameter of 250-270 nm and a particle size distribution of 0.34 for multiblock copolymers containing PAA22 and 0.17 for those containing PAA63. Upon increasing the pH to 7.4, both types of particles were able to swell without being disintegrated, reaching an average diameter of 285-300 nm for [PAA22-VG2]n and 330-350 nm for [PAA63-VG2]n, respectively. The nanoparticles were not dissociated upon the addition of urea, further confirming their unusual stability. The nanoparticles were capable of sequestering a hydrophobic fluorescent dye (pyrene), and the critical aggregation concentration (CAC) was determined to be 1.09 × 10-2 or 1.05 × 10-2 mg/mL for [PAA22-VG2]n and [PAA63-VG2]n, respectively. We suggest that the multiblock copolymers form through collective H-bonding and hydrophobic interactions between the PAA and VG2 peptide units, and that the unusual stability of the multiblock nanoparticles is conferred by the multiblock architecture. These hybrid multiblock copolymers are potentially useful as pH-responsive drug delivery vehicles, with the possibility of drug loading through

  4. Synthesis, characterization, and swelling behaviors of salt-sensitive maize bran-poly(acrylic acid) superabsorbent hydrogel.

    PubMed

    Zhang, Mingyue; Cheng, Zhiqiang; Zhao, Tianqi; Liu, Mengzhu; Hu, Meijuan; Li, Junfeng

    2014-09-01

    A novel composite hydrogel was prepared via UV irradiation copolymerization of acrylic acid and maize bran (MB) in the presence of composite initiator (2,2-dimethoxy-2-phenylacetophenone and ammonium persulfate) and cross-linker (N,N'-methylenebis(acrylamide)). Under the optimized conditions, maize bran-poly(acrylic acid) was obtained (2507 g g(-1) in distilled water and 658 g g(-1) in 0.9 wt % NaCl solution). Effects of granularity, salt concentration, and various cations and anions on water absorbency were investigated. It was found that swelling was extremely sensitive to the ionic strength and cation and anion type. Swelling kinetics and water diffusion mechanism in distilled water were also discussed. Moreover, the product showed excellent water retention capability under the condition of high temperature or high pressure. The salt sensitivity, good water absorbency, and excellent water retention capability of the hydrogels give this intelligentized polymer wide potential applications. PMID:25133321

  5. Preparation, characterization, and antibacterial activity studies of silver-loaded poly(styrene-co-acrylic acid) nanocomposites.

    PubMed

    Song, Cunfeng; Chang, Ying; Cheng, Ling; Xu, Yiting; Chen, Xiaoling; Zhang, Long; Zhong, Lina; Dai, Lizong

    2014-03-01

    A simple method for preparing a new type of stable antibacterial agent was presented. Monodisperse poly(styrene-co-acrylic acid) (PSA) nanospheres, serving as matrices, were synthesized via soap-free emulsion polymerization. Field-emission scanning electron microscopy micrographs indicated that PSA nanospheres have interesting surface microstructures and well-controlled particle size distributions. Silver-loaded poly(styrene-co-acrylic acid) (PSA/Ag-NPs) nanocomposites were prepared in situ through interfacial reduction of silver nitrate with sodium borohydride, and further characterized by transmission electron microscopy and X-ray diffraction. Their effects on antibacterial activity including inhibition zone, minimum inhibitory concentration (MIC), minimum bactericidal concentration (MBC), and bactericidal kinetics were evaluated. In the tests, PSA/Ag-NPs nanocomposites showed excellent antibacterial activity against both gram-positive Staphylococcus aureus and gram-negative Escherichia coli. These nanocomposites are considered to have potential application in antibacterial coatings on biomedical devices to reduce nosocomial infection rates. PMID:24433897

  6. Lactic acid conversion to 2,3-pentanedione and acrylic acid over silica-supported sodium nitrate: Reaction optimization and identification of sodium lactate as the active catalyst

    SciTech Connect

    Wadley, D.C.; Tam, M.S.; Miller, D.J.

    1997-01-15

    Lactic acid is converted to 2,3-pentanedione, acrylic acid, and other products in vapor-phase reactions over silica-supported sodium lactate formed from sodium nitrate. Multiparameter optimization of reaction conditions using a Box-Benkhen experimental design shows that the highest yield and selectivity to 2,3-pentanedione are achieved at low temperature, elevated pressure, and long contact time, while yield and selectivity to acrylic acid are most favorable at high temperature, low pressure, and short contact time. Post-reaction Fourier transform infrared spectroscopic analyses of the catalyst indicate that sodium nitrate as the initial catalyst material is transformed to sodium lactate at the onset of reaction via proton transfer from lactic acid to nitrate. The resultant nitric acid vaporizes as it is formed, leaving sodium lactate as the sole sodium-bearing species on the catalyst during reaction. 19 refs., 8 figs., 5 tabs.

  7. Rapid 3D Patterning of Poly(acrylic acid) Ionic Hydrogel for Miniature pH Sensors.

    PubMed

    Yin, Ming-Jie; Yao, Mian; Gao, Shaorui; Zhang, A Ping; Tam, Hwa-Yaw; Wai, Ping-Kong A

    2016-02-17

    Poly(acrylic acid) (PAA), as a highly ionic conductive hydrogel, can reversibly swell/deswell according to the surrounding pH conditions. An optical maskless -stereolithography technology is presented to rapidly 3D pattern PAA for device fabrication. A highly sensitive miniature pH sensor is demonstrated by in situ printing of periodic PAA micropads on a tapered optical microfiber. PMID:26643765

  8. A novel poly(acrylic acid-co-acrylamide)/diatomite composite flocculant with outstanding flocculation performance.

    PubMed

    Xu, Kun; Liu, Yao; Wang, Yang; Tan, Ying; Liang, Xuecheng; Lu, Cuige; Wang, Haiwei; Liu, Xiusheng; Wang, Pixin

    2015-01-01

    Series of anionic flocculants with outstanding flocculation performance, poly(acrylic acid-co-acrylamide)/diatomite composite flocculants (PAAD) were successfully prepared through aqueous solution copolymerization and applied to flocculate from oil-field fracturing waste-water. The structure of PAAD was characterized by Fourier transform infra-red spectroscopy, (13)C nuclear magnetic resonance and X-ray diffraction tests, and its properties were systematically evaluated by viscometer, thermogravimetry analysis and flocculation measurements. Furthermore, the influences of various reaction parameters on the apparent viscosity of flocculant solution were studied, and the optimum synthesis condition was determined. The novel composite flocculants exhibited outstanding flocculation properties. Specifically, the dosage of composite flocculants that could make the transmittance of treated wastewater exceed 90% was only approximately 12-35 ppm, which was far lower than that of conventional flocculants. Meanwhile, the settling time was lower than 5 s, which was similar to that of conventional flocculants. This was because PAAD flocculants had a higher absorption capacity, and larger chain extending space than conventional linear flocculants, which could refrain from the entanglement of linear polymer chains and significantly improve flocculation capacity. PMID:26360748

  9. Potassium fulvate as co-interpenetrating agent during graft polymerization of acrylic acid from cellulose.

    PubMed

    Ghazy, Mohamed B M; El-Hai, Farag Abd; Mohamed, Magdy F; Essawy, Hisham A

    2016-10-01

    Grafting polymerization of acrylic acid onto cellulose in presence of potassium fulvate (KF) as a co-interpenetrating agent results enhanced water sorption compared to materials prepared similarly in its absence. The insertion of potassium fulvate (KF) did not affect the grafting process and is thought to proceed in parallel to the graft polymerization via intensive polycondensation reactions of its function groups (-COOH and OH) with COOH of the monomer and OH groups of cellulose. The combination of graft copolymerization and polycondensation reactions is assumed to produce interpenetrating network structure. Fourier transform infrared (FTIR) confirmed successful incorporation within the network structure which is an evidence for formation of interpenetrating network. The obtained structures showed homogeneous uniform surface as revealed by scanning electron microscopy (SEM). The obtained superabsorbent possessed high water absorbency 422 and 48.8g/g in distilled water and saline (0.9wt.% NaCl solution), respectively, and enhanced water retention even at elevated temperatures as revealed by thermogravimetric analysis (TGA). This could be explained by the high content of hydrophilic groups. The new superabsorbents proved to be efficient devices for controlled release of fertilizers which expands their use in agricultural applications. PMID:27370745

  10. Investigation of electrochemical properties of a poly(vinyl alcohol)/poly(acrylic acid) polymer blend

    SciTech Connect

    DeSantis, C.O.; Seliskar, C.; Heineman, W.R.

    1995-12-31

    Chemical sensors have wide applications in medicine, environmental monitoring, industrial applications, and others because of their versatility, ruggedness, sensitivity, selectivity, and economy. Electrochemical sensors are constructed by using a conducting medium, in this case graphite, and applying a constant potential while measuring changes in the current. Polymers are used for electrochemical sensors to exclude interferents from the electrode surface, to preconcentrate the analyte near the electrode, and in some cases to provide a matrix for the immobilization of analytes, such as enzymes. These functions of the polymer can serve to improve the detection limit of the sensor. This project involves the evaluation of a new polymer for electrode modification. The poly(vinyl alcohol)/poly(acrylic acid) (PVA/PAA) polymer was originally developed as an ion exchanger for use in space batteries. It has also been used in wastewater cleanup because it will concentrate heavy metals in the presence of calcium ion. This polymer is also optically clear, so it can potentially be used for an optical sensor. We are interested in investigating the ion exchange properties of the PVA/PAA polymer, as well as the ability of this polymer to preconcentrate and exclude analytes on the basis of size, charge, and hydrophilic/hydrophobic interactions.

  11. Poly(acrylic acid) brushes pattern as a 3D functional biosensor surface for microchips

    NASA Astrophysics Data System (ADS)

    Wang, Yan-Mei; Cui, Yi; Cheng, Zhi-Qiang; Song, Lu-Sheng; Wang, Zhi-You; Han, Bao-Hang; Zhu, Jin-Song

    2013-02-01

    Poly(acrylic acid) (PAA) brushes, a novel three dimensional (3D) precursor layer of biosensor or protein microarrays, possess high protein loading level and low non-specific protein adsorption. In this article, we describe a simple and convenient way to fabricate 3D PAA brushes pattern by microcontact printing (μCP) and characterize it with FT-IR and optical microscopy. The carboxyl groups of PAA brushes can be applied to covalently immobilize protein for immunoassay. Thriving 3D space made by patterning PAA brushes thin film is available to enhance protein immobilization, which is confirmed by measuring model protein interaction between human immunoglobulin G (H-IgG) and goat anti-H-IgG (G-H-IgG) with fluorescence microscopy and surface plasmon resonance imaging (SPRi). As expected, the SPRi signals of H-IgG coating on 3D PAA brushes pattern and further measuring specific binding with G-H-IgG are all larger than that of 3D PAA brushes without pattern and 2D bare gold surface. We further revealed that this surface can be used for high-throughput screening and clinical diagnosis by label-free assaying of Hepatitis-B-Virus surface antibody (HBsAb) with Hepatitis-B-Virus surface antigen (HBsAg) concentration array chip. The linearity range for HBsAb assay is wider than that of conventional ELISA method.

  12. Cellulose nanocrystal-filled poly(acrylic acid) nanocomposite fibrous membranes

    NASA Astrophysics Data System (ADS)

    Lu, Ping; Hsieh, You-Lo

    2009-10-01

    Nanocomposite fibrous membranes have been fabricated by electrospinning cellulose nanocrystal (CNC)-loaded poly(acrylic acid) (PAA) ethanol mixtures. Incorporating CNC in PAA significantly reduced fiber diameters and improved fiber uniformity. The average diameters of the as-spun nanocomposite fibers were significantly reduced from 349 nm to 162 nm, 141 nm, 90 nm and 69 nm at 5%, 10%, 15% and 20% CNC loading (by weight of a constant 4% PAA solution), respectively. CNC was well dispersed in the fibers as isolated rods oriented along the fiber axis and as spheres in the PAA matrix. The Young modulus and stress of the PAA/CNC nanocomposite fibers were significantly improved with increasing CNC loadings by up to 35-fold and 16-fold, respectively. Heat-induced esterification between the CNC surface hydroxyls and PAA carboxyl groups produced covalent crosslinks at the CNC-PAA interfaces, rendering the nanocomposite fibrous membranes insoluble in water, more thermally stable and far more superior in tensile strength. With 20% CNC, the crosslinked nanocomposite fibrous membrane exhibited a very impressive 77-fold increase in modulus and 58-fold increase in stress.

  13. Surfactants modify the release from tablets made of hydrophobically modified poly (acrylic acid)☆

    PubMed Central

    Knöös, Patrik; Onder, Sebla; Pedersen, Lina; Piculell, Lennart; Ulvenlund, Stefan; Wahlgren, Marie

    2013-01-01

    Many novel pharmaceutically active substances are characterized by a high hydrophobicity and a low water solubility, which present challenges for their delivery as drugs. Tablets made from cross-linked hydrophobically modified poly (acrylic acid) (CLHMPAA), commercially available as Pemulen™, have previously shown promising abilities to control the release of hydrophobic model substances. This study further investigates the possibility to use CLHMPAA in tablet formulations using ibuprofen as a model substance. Furthermore, surfactants were added to the dissolution medium in order to simulate the presence of bile salts in the intestine. The release of ibuprofen is strongly affected by the presence of surfactant and/or buffer in the dissolution medium, which affect both the behaviour of CLHMPAA and the swelling of the gel layer that surrounds the disintegrating tablets. Two mechanisms of tablet disintegration were observed under shear, namely conventional dissolution of a soluble tablet matrix and erosion of swollen insoluble gel particles from the tablet. The effects of surfactant in the surrounding medium can be circumvented by addition of surfactant to the tablet. With added surfactant, tablets that may be insusceptible to the differences in bile salt level between fasted or fed states have been produced, thus addressing a central problem in controlled delivery of hydrophobic drugs. In other words CLHMPAA is a potential candidate to be used in tablet formulations for controlled release with poorly soluble drugs. PMID:25755999

  14. Preparation and Biophysical Characterization of Poly(amidoamine) Dendrimer-Poly(acrylic acid) Graft.

    PubMed

    Dung, Tran Huu; Do, Le Thanh; Loan, Ta Thi; Yoo, Hoon

    2015-01-01

    A series of PAMAM dendrimer generation 5-poly(acrylic acid) grafts were prepared to evaluate the potential use of dendritic grafts as a drug encapsulated nanocarrier. The structural features of the synthesized polymer graft were identified by FT-IR and 1H-NMR spectra and the biophysical properties were characterized by measuring its particle size and zeta potential. The prepared dendrimer G5-PAA grafts had particle size in the range of 600 to 900 nm and the size increased proportionally with the number of PAA on dendrimer surface. The electrostatic property of the dendrimer G5-PAA, carried out by HPLC reversed phase column analysis and the measurement of zeta potential, revealed that both migration time and zeta potential were dependent on the number of grafted PAA. The number of free amino groups on dendrimer G5-PAA, determined quantitatively by fluorescamine assay, was in a reverse order with the reaction mole ratio of dendrimer to PAA. In addition, dendrimer G5-PAA showed a pH-dependent solubility in aqueous solution with characteristic pH region of solubility, depending on the dendrimer generation. The observed biophysical properties indicate that PAMAM dendrimer G5-PAA is promising as a drug encapsulated nanocarrier. PMID:26328427

  15. Adsorption of poly acrylic acid onto the surface of calcite: an experimental and simulation study.

    PubMed

    Sparks, David J; Romero-González, Maria E; El-Taboni, Elfateh; Freeman, Colin L; Hall, Shaun A; Kakonyi, Gabriella; Swanson, Linda; Banwart, Steven A; Harding, John H

    2015-11-01

    Macromolecular binding to minerals is of great importance in the formation of biofilms, and carboxylate functional groups have been found to play a pivotal role in the functioning of these macromolecules. Here we present both fluorescence time-resolved anisotropy measurements and simulation data on the conformational behaviour and binding of a poly acrylic acid polymer. In solution the polymer exhibits a pH dependent behaviour, with a coiled conformation at a low pH and extended conformation at higher pH values. The polymer is readily adsorbed on the surface of calcite, preferring to bind in an extended conformation, with the strength of the adsorption dependent on the pH and presence of counter ions. We discuss the reasons why the calculated adsorption free energy differs from that obtained from a Langmuir isotherm analysis, showing that they refer to different quantities. The enhanced binding of the extended conformations shows the importance of flexibility in the binding of macromolecules. PMID:26418100

  16. Antimicrobial activity of poly(vinyl alcohol)-poly(acrylic acid) electrospun nanofibers.

    PubMed

    Santiago-Morales, Javier; Amariei, Georgiana; Letón, Pedro; Rosal, Roberto

    2016-10-01

    Electrospun nanofibers were prepared from blends of poly(acrylic acid) (PAA) and poly(vinyl alcohol) (PVA). The fibers were stabilized by heat curing at 140°C via anhydride and ketone formation and crosslinking esterification. The antimicrobial effect was assessed using strains of Escherichia coli and Staphylococcus aureus by tracking their capacity to form colonies and their metabolic impairment upon contact with PAA/PVA membranes. Membranes containing >35wt.% PAA displayed significant antibacterial activity, which was particularly high for the gram-positive S. aureus. All membranes were negatively charged, with surface ζ-potential in the (-34.5)-(-45.6)mV range, but the electrostatic interaction with the negatively charged cells was not the reason for the antimicrobial effect. Neither pH reduction nor the passing of non-crosslinked polymers to the solution affected microbial growth. The antibacterial activity was attributed to the chelation of the divalent cations stabilizing the outer cell membrane. The effect on gram-positive bacteria was attributed to the destabilization of the peptidoglycan layer. The sequestration of divalent cations was demonstrated with experiments in which calcium and a chelating agent were added to the cultures in contact with membranes. The damage to bacterial cells was tracked by measuring their surface charge and the evolution of intracellular calcium during the early stages after contact with PAA/PVA membranes. PMID:27318959

  17. Mechanically stable thermally crosslinked poly(acrylic acid)/reduced graphene oxide aerogels.

    PubMed

    Ha, Heonjoo; Shanmuganathan, Kadhiravan; Ellison, Christopher J

    2015-03-25

    Graphene oxide (GO) aerogels, high porosity (>99%) low density (∼3-10 mg cm(-3)) porous materials with GO pore walls, are particularly attractive due to their lightweight, high surface area, and potential use in environmental remediation, superhydrophobic and superoleophilic materials, energy storage, etc. However, pure GO aerogels are generally weak and delicate which complicates their handling and potentially limits their commercial implementation. The focus of this work was to synthesize highly elastic, mechanically stable aerogels that are robust and easy to handle without substantially sacrificing their high porosity or low density. To overcome this challenge, a small amount of readily available and thermally cross-linkable poly(acrylic acid) (PAA) was intermixed with GO to enhance the mechanical integrity of the aerogel without disrupting other desirable characteristic properties. This method is a simple straightforward procedure that does not include multistep or complicated chemical reactions, and it produces aerogels with mass densities of about 4-6 mg cm(-3) and >99.6% porosity that can reversibly support up to 10,000 times their weight with full recovery of their original volume. Finally, pressure sensing capabilities were demonstrated and their oil absorption capacities were measured to be around 120 g oil per g aerogel(-1) which highlights their potential use in practical applications. PMID:25714662

  18. Preparation and properties of poly(acrylic acid) oligomer stabilized superparamagnetic ferrofluid.

    PubMed

    Lin, Chia-Lung; Lee, Chia-Fen; Chiu, Wen-Yen

    2005-11-15

    Ferrofluids, which are stable dispersions of magnetic particles, behave as liquids that have strong magnetic properties. Nanoparticles of magnetite with a mean diameter of 10-15 nm, which are in the range of superparamagnetism, are usually prepared by the traditional method of co-precipitation from ferrous and ferric electrolyte solution. When diluted, the ferrofluid dispersions are not stable if anionic or cationic surfactants are used as the stabilizer. This work presents an efficient way to prepare a stable aqueous nanomagnetite dispersion. A stable ferrofluid containing Fe3O4 nanoparticles was synthesized via co-precipitation in the presence of poly(acrylic acid) oligomer. The mechanism, microstructure, and properties of the ferrofluid were investigated. The results indicate that the PAA oligomers promoted the nucleation and inhibited the growth of the magnetic iron oxide, and the average diameter of each individual Fe3O4 particle was smaller than 10 nm. In addition, the PAA oligomers provided both electrostatic and steric repulsion against particle aggregation, and the stability of dispersions could be controlled by adjusting the pH value of solution. A small amount of Fe2O3 was found in the nanoparticles but the superparamagnetic behavior of the nanoparticles was not affected. PMID:16009367

  19. Synthesis, structure and phase transition property of acrylic acid grafted paraffin

    NASA Astrophysics Data System (ADS)

    Zhao, Xiaowen; Liu, Pengfei; Ye, Lin

    2014-05-01

    Polar monomer acrylic acid (AA) was used to modify paraffin in order to improve the latent heat of paraffin as phase change materials. The composition and sequence structure of the grafted products were characterized by FTIR, 13C NMR, 1H NMR and GPC analysis, and the thermal properties of paraffin-g-AA were investigated. It was found that AA was confirmed to be grafted onto the molecular chain of paraffin successfully. The mechanism of free radical grafting of AA may be only monomeric grafts. At low grafting ratio, the structure B can be mainly formed as a result of the radical coupling termination; while at the high grafting ratio, structure A was the primary structure as a result of the radical chain growth process. The number-average molecular weight of the grafted samples increased at first but leveled off with increasing grafting ratio, while the weight-average molecular weight increased gradually. The latent heat capacity of the grafted paraffin can be improved obviously at low grafting ratio due to the formation of structure B.

  20. Multiplex Immunoassay Platforms Based on Shape-Coded Poly(ethylene glycol) Hydrogel Microparticles Incorporating Acrylic Acid

    PubMed Central

    Park, Saemi; Lee, Hyun Jong; Koh, Won-Gun

    2012-01-01

    A suspension protein microarray was developed using shape-coded poly(ethylene glycol) (PEG) hydrogel microparticles for potential applications in multiplex and high-throughput immunoassays. A simple photopatterning process produced various shapes of hydrogel micropatterns that were weakly bound to poly(dimethylsiloxane) (PDMS)-coated substrates. These micropatterns were easily detached from substrates during the washing process and were collected as non-spherical microparticles. Acrylic acids were incorporated into hydrogels, which could covalently immobilize proteins onto their surfaces due to the presence of carboxyl groups. The amount of immobilized protein increased with the amount of acrylic acid due to more available carboxyl groups. Saturation was reached at 25% v/v of acrylic acid. Immunoassays with IgG and IgM immobilized onto hydrogel microparticles were successfully performed with a linear concentration range from 0 to 500 ng/mL of anti-IgG and anti-IgM, respectively. Finally, a mixture of two different shapes of hydrogel microparticles immobilizing IgG (circle) and IgM (square) was prepared and it was demonstrated that simultaneous detection of two different target proteins was possible without cross-talk using same fluorescence indicator because each immunoassay was easily identified by the shapes of hydrogel microparticles. PMID:22969408

  1. Oleanolic acid acrylate elicits antidepressant-like effect mediated by 5-HT1A receptor

    PubMed Central

    Fajemiroye, James O.; Polepally, Prabhakar R.; Chaurasiya, Narayan D.; Tekwani, Babu L.; Zjawiony, Jordan K.; Costa, Elson A.

    2015-01-01

    The development of new drugs for the treatment of depression is strategic to achieving clinical needs of patients. This study evaluates antidepressant-like effect and neural mechanisms of four oleanolic acid derivatives i.e. acrylate (D1), methacrylate (D2), methyl fumarate (D3) and ethyl fumarate (D4). All derivatives were obtained by simple one-step esterification of oleanolic acid prior to pharmacological screening in the forced swimming (FS) and open field (OF) tests. Pharmacological tools like α-methyl-p-tyrosine (AMPT, catecholamine depletor), p-chlorophenylalanine (serotonin depletor), prazosin (PRAZ, selective α1-receptor antagonist), WAY-100635 (selective serotonin 5-HT1A receptor antagonist) as well as monoamine oxidase (MAO) and functional binding assays were conducted to investigate possible neural mechanisms. In the FS test, D1 showed the most promising antidepressant-like effect without eliciting locomotor incoordination. Unlike group of mice pretreated with AMPT 100 mg/kg, PCPA 100 mg/kg or PRAZ 1 mg/kg, the effect of D1 was attenuated by WAY-100635 0.3 mg/kg pretreatment. D1 demonstrated moderate inhibition of MAO-A (IC50 = 48.848 ± 1.935 μM), potency (pEC50 = 6.1 ± 0.1) and intrinsic activity (Emax = 26 ± 2.0%) on 5-HT1A receptor. In conclusion, our findings showed antidepressant-like effect of D1 and possible involvement of 5-HT1A receptor. PMID:26199018

  2. A study on the effect of the concentration of N,N-methylenebisacrylamide and acrylic acid toward the properties of Dioscorea hispida-starch-based hydrogel

    NASA Astrophysics Data System (ADS)

    Ashri, Airul; Lazim, Azwan

    2014-09-01

    The research investigated the effects of acrylic acid (monomer) and N,N,-methylenebisacrylamide, MBA (crosslinker) toward the percentage of gel content, swelling ratio and ionic strength of a starch-based hydrogel. Starch grafted on poly (sodium acrylate), St-g-PAANa hydrogel was prepared by incorporating starch extracted from Dioscorea hispida in NaOH/aqueous solution using different composition of acrylic acid (AA) and N,N-methylenebisacrylamide (MBA) in the presence of potassium persulfate (KPS) as chemical initiator. The highest gel content was observed at 1:30 ratio of starch to AA and 0.10 M of MBA. Results showed the highest swelling ratio was observed at 1:15 ratio of starch to acrylic acid and 0.02 M of MBA solution. The same results also gave the highest swelling ratio for the ionic strength study. The FTIR analysis was also conducted in order to confirm the grafting of AA onto starch backbone.

  3. The C-F...F-C short contacts in the metal complexes of fluoro-phenyl-acrylic acids

    SciTech Connect

    Liu Guilei; Liu CaiMing; Li Hui

    2011-03-15

    Four new complexes of fluoro-phenyl-acrylic acids (E)-3-(3-fluoro-phenyl)-acrylic acid (L1) [Mn{sub 3}(L1){sub 6}(L2){sub 2}].H{sub 2}O.CH{sub 3}CN (1), [Zn{sub 2}(L1){sub 4}(L3)]{sub n} (2), [Mn(L1){sub 2}(H{sub 2}O){sub 2}]{sub n} (3) and [Co(L1){sub 2}(H{sub 2}O){sub 2}]{sub n} (4) (L2=1,10-phenanthroline, L3=4,4'-bipy) have been synthesized based on the molecular design and research of halogen-halogen interactions (especially fluoro-fluoro contact). The structure analyses reveal that complex 1 is a trinuclear complex, which is blocked by L2. Complex 2 is a 1D chain bridged through L3. Complexes 3 and 4 exhibit 2D grid like metal-organic framework structures through carboxylato bridge ligand. Variable-temperature magnetic measurements showed an antiferromagnetic interaction between Mn(II) ions and between Co(II) ions in complexes 3 and 4, respectively. A short C-F...F-C contact with a distance of 2.953 A was found between the trinuclear coordination compound 1. -- Graphical Abstract: The short distance between F...F (2.953 A) was found in the complex of [Mn{sub 3}(L1){sub 6}(L2){sub 2}].H{sub 2}O.CH{sub 3}CN (L1=(E)-3-(3-fluoro-phenyl)-acrylic acid, L2=1,-10-phenanthroline). Display Omitted Research highlights: > Four new complexes of fluoro-phenyl-acrylic acids (E)-3-(3-fluoro-phenyl)-acrylic acid (L1) [Mn{sub 3}(L1){sub 6}(L2){sub 2}].H{sub 2}O.CH{sub 3}CN (1), [Zn{sub 2}(L1){sub 4}(L3)]{sub n} (2), [Mn(L1){sub 2}(H{sub 2}O){sub 2}]{sub n} (3) and [Co(L1){sub 2}(H{sub 2}O){sub 2}]{sub n} (4) (L2=1,10-phenanthroline, L3=4,4'-bipy) have been synthesized based on the molecular design and research of halogen-halogen interactions (especially fluoro-fluoro contact). > A short C-F...F-C contact with a distance of 2.953 A was found between the trinuclear coordination compound 1. > Variable-temperature magnetic measurements showed an antiferromagnetic interaction between Mn(II) ions and between Co(II) ions in complexes 3 and 4, respectively.

  4. Transport in Porous Media of Poly(Acrylic Acid) Coated Ferrihydrite Nanoparticles

    NASA Astrophysics Data System (ADS)

    Jaffe, P. R.; Xiang, A.; Koel, B. E.

    2012-12-01

    Augmentation of soils with iron to enhance biological processes such as uranium reduction via iron reducing bacteria, e.g., Geobacter sp., might be achieved via the injection of iron nanoparticles into the subsurface. The challenge is to make these nanoparticles transportable in the subsurface while not affecting the iron bioavailability. Poorly crystallized 2-line ferrihydrite iron oxide nanoparticles were synthesized and coated with different amounts of poly(acrylic acid) polymers (Na-PAA6K or Na-PAA140K). Analyses were then performed on these particles, including sorption/desorption of the polymer onto the iron nanoparticles, particle size, zeta potential, transport in sand and soil columns, and bioavailabity of the Fe(III) in the absence and presence of the coating to iron reducing organisms. Results showed that at pH values of environmental relevance, the zeta potential of the particles varied from about 3 mV (pH=8.2) for the non-coated particles to about -30 mV for the particles coated with the polymers to their highest sorption capacity. The coated particle diameter was shown to be in the range of 200 nm. Column transport experiments showed that for the highest polymer coating the nanoparticle breakthrough was virtually identical to that of bromide, while significant filtration was observed for particles with an intermediate coating, and complete particle removal via filtration was observed for the non-coated particles. These results held for sand as well as for soil, which had been previously characterized, from a field site at Rifle, CO. Bioavailability experiments showed no difference in the iron reduction rate between the untreated and treated nanoparticles. These results show that it is possible to manufacture iron nanoparticles to enhance biological iron reduction, and that the transport properties of these treated particles is tunable so that a desired retention in the porous medium can be achieved.

  5. Synthesis and characterization of poly(acrylic acid) stabilized cadmium sulfide quantum dots.

    PubMed

    Celebi, Serdar; Erdamar, A Koray; Sennaroglu, Alphan; Kurt, Adnan; Acar, Havva Yagci

    2007-11-01

    Cadmium sulfide (CdS) nanoparticles (NPs) capped with poly(acrylic acid) (PAA) were prepared in aqueous solutions from Cd(NO3)2 and Na2S. Influence of the COOH/Cd ratio (0.8-12.5), reaction pH (5.5 and 7.5), and PAA molecular weight (2100 and 5100 g/mol) on the particle size, colloidal stability, and photoluminescence were investigated. A Cd/S ratio of <1 causes ineffective passivization of the surface with the carboxylate and therefore results in a red shift of the absorption band and a significant drop in photoluminescence. Therefore, the Cd/S ratio was fixed at 1.1 for all experiments studying the mentioned variables. PAA coating provided excellent colloidal stability at a COOH/Cd ratio above 1. Absorption edges of PAA-coated CdS NPs are in the range of 460-508 nm. The size of the NPs increases slightly with increasing PAA molecular weight and COOH/Cd ratio at pH 7.5. It is demonstrated that there is a critical COOH/Cd ratio (1.5-2) that maximizes the photoluminescence intensity and quantum yield (QY, 17%). Above this critical ratio, which corresponds to smaller crystal sizes (3.7-4.1 nm) for each reaction set, the quantum yield decreases and the crystal size increases. Moreover, CdS NPs prepared at pH 7.5 have significantly higher QY and absorb at lower wavelengths in comparison with those prepared at pH 5.5. Luminescence quenching has not been observed over 8 months. PMID:17929960

  6. Anelastic and thermal properties of ethylene/acrylic acid copolymers partially ionized with transition metals

    SciTech Connect

    Hoffman, D.M.; Matthews, F.M.; Riley, M.O.; Walkup, C.M.

    1988-01-01

    Ionomers of five 3d series transition metals (Mn, Fe, Co, Ni, and Cu), two Lanthanide series transition metals (Ce, Sm) and the IV and V series metals (Pb, Bi) were prepared by reaction with 25% solids dispersion of poly (ethylene-co-acrylic acid), EAA, in aqueous ammonia. The unreacted copolymer showed two mechanical relaxations, the glass transition at about 5C and a low temperature secondary relaxation at about -140C with 230 +- 10 kJ/mol and 50+-8 kJ/mol apparent activation energies, respectively. Typically three weight percent of the metal nitrate or acetate was reacted with the copolymer dispersion. After precipitation, drying and molding, the ionomers showed three mechanical relaxations. The low temperature ..gamma..-relaxation was quite strong and shifted about 5C higher compared to the EAA copolymer. The ..beta..-relaxation was extremely weak occurring at -62+-5C in the loss tangent at 1.0 Hz. The ..cap alpha..-relaxation or glass transition for 3% transition metal ionomers occurred at about 26+-3C for +3 oxidation states and Cu/sup +2/, but significantly higher for other +2 oxidation states (48 +- 2C for Co, Ni and 35C for Mn) based on G'' maxima at 1.0 Hz and the apparent activation energy was 220+-30kJ/mol. The two group IV and V metal ionomers were much higher loadings and had a much broader and stronger (..beta..') relaxation occurring at -6 +- 4C with 130+-10 kJ/mol activation energies. The lead ionomers were clear but the bismuth ionomer showed macroscopic phase separation. The 3d transition metal ionomers were clear and nicely colored characteristic of their ionization state except for iron which was somewhat cloudy. The Lanthanide ionomers were clear (Ce) or pale yellow (Sm) and also reasonably transparent. (16 refs., 12 figs., 5 tabs.)

  7. Production of dimethylsulfide and acrylic acid from dimethylsulfoniopropionate during growth of three marine microalgae

    NASA Astrophysics Data System (ADS)

    Liu, Chunying; Gao, Caixia; Zhang, Haibo; Chen, Shuo; Deng, Ping; Yue, Xin'an; Guo, Xiaoyi

    2014-07-01

    We measured the concentrations of dimethylsulfide (DMS), acrylic acid (AA), and dimethylsulfoniopropionate (DMSP) during growth of three microalgae: Prorocentrum micans, Gephyrocapsa oceanica, and Platymonas subcordiformis. The DMSP, AA, and DMS concentrations in culture media varied significantly among algal growth stages, with the highest concentrations in the late stationary growth stage or the senescent stage. In the stationary growth stage, the average DMSP concentration per cell in P. mican s (0.066 5 pmol/cell) was 1.3 times that in G. oceanica (0.049 5 pmol/cell) and 20.2 times that in P. subcordiformi s (0.003 29 pmol/cell). The average concentrations of AA were 0.044 6, 0.026 9, and 0.003 05 pmol/cell in P. micans, G. oceanica, and P. subcordiformi s, respectively, higher than the concentrations of DMS (0.272, 0.497, and 0.086 2 fmol/cell, respectively). There were significant positive correlations between cell density and AA, DMSP, and DMS concentrations. The ratios of DMS /AA and AA /(DMSP+AA) in the three algae differed significantly over the growth cycle. In all three microalgae, the DMS/AA ratios were less than 25% during the growth period, suggesting that the enzymatic cleavage pathway, which generates DMS, was not the main DMSP degradation pathway. The changes in the DMS/AA ratio indicated that there was a higher rate of enzymatic breakdown of DMSP in the early growth period and a lower rate during senescence. In all three microalgae, the AA /(DMSP+AA) ratio (degradation ratio of DMSP) decreased during the exponential growth phase, and then increased. The variations in these ratios can approximately indicate the cleavage mechanism of DMSP at different stages of algal growth.

  8. Production of dimethylsulfide and acrylic acid from dimethylsulfoniopropionate during growth of three marine microalgae

    NASA Astrophysics Data System (ADS)

    Liu, Chunying; Gao, Caixia; Zhang, Haibo; Chen, Shuo; Deng, Ping; Yue, Xin'an; Guo, Xiaoyi

    2014-11-01

    We measured the concentrations of dimethylsulfide (DMS), acrylic acid (AA), and dimethylsulfoniopropionate (DMSP) during growth of three microalgae: Prorocentrum micans, Gephyrocapsa oceanica, and Platymonas subcordiformis. The DMSP, AA, and DMS concentrations in culture media varied significantly among algal growth stages, with the highest concentrations in the late stationary growth stage or the senescent stage. In the stationary growth stage, the average DMSP concentration per cell in P. micans (0.066 5 pmol/cell) was 1.3 times that in G. oceanica (0.049 5 pmol/cell) and 20.2 times that in P. subcordiformis (0.003 29 pmol/cell). The average concentrations of AA were 0.044 6, 0.026 9, and 0.003 05 pmol/cell in P. micans, G. oceanica, and P. subcordiformi s, respectively, higher than the concentrations of DMS (0.272, 0.497, and 0.086 2 fmol/cell, respectively). There were significant positive correlations between cell density and AA, DMSP, and DMS concentrations. The ratios of DMS/AA and AA/(DMSP+AA) in the three algae differed significantly over the growth cycle. In all three microalgae, the DMS/AA ratios were less than 25% during the growth period, suggesting that the enzymatic cleavage pathway, which generates DMS, was not the main DMSP degradation pathway. The changes in the DMS/AA ratio indicated that there was a higher rate of enzymatic breakdown of DMSP in the early growth period and a lower rate during senescence. In all three microalgae, the AA/(DMSP+AA) ratio (degradation ratio of DMSP) decreased during the exponential growth phase, and then increased. The variations in these ratios can approximately indicate the cleavage mechanism of DMSP at different stages of algal growth.

  9. Studies on surface grafting of AAc/SSS binary monomers onto polytetrafluoroethylene by dielectric barrier discharge initiation

    NASA Astrophysics Data System (ADS)

    Xi, Zhen-Yu; Xu, You-Yi; Zhu, Li-Ping; Liu, Fu; Zhu, Bao-Ku

    2008-09-01

    Polytetrafluoroethylene (PTFE) films were pre-treated by dielectric barrier discharge in atmospheric pressure with air as carrier gas. And then the hydrophilic sulfonate groups were introduced by the single step grafting method with binary monomer solution of acrylic acid (AAc) and sodium 4-styrenesulfonate (SSS). The effects of binary monomer ratio, reaction solution concentration and polymerization time on the degree of grafting were investigated. The surface chemical change was determined by Fourier transform infrared attenuated total reflection spectroscopy (FTIR-ATR) and X-ray photoelectron spectroscopy (XPS). Morphological changes on the film surface were described using field emitting scanning electron microscopy (SEM) and atomic force microscopy (AFM). The surface hydrophilicity of the modified film was characterized through water contact angle measurement. It was found that the water contact angle of the film surface reduced significantly when compared with the original one, indicating the introduction of hydrophilic groups and improvement of the surface hydrophilicity.

  10. Synthesis and physicochemical properties of organofluorine esters of acrylic, methacrylic, and maleic acids

    SciTech Connect

    Gol'din, G.S.; Averbakh, K.O.; Lavygin, I.A.; Nekrasova, L.A.

    1985-12-01

    The authors synthesize and study the physicochemical properties of organofluorine acrylates, methacrylates, and maleates. The organofluorine esters are colorless liquids; their composition and structure were confirmed by elemental analysis and IR spectra. The results of studies of the dependence of the density, surface tension, and viscosity of these compounds on temperature are presented. The results revealed the influence of the length of the fluorocarbon chain on the combination of the physicochemical properties of organofluorine acrylates, methacrylates, and maleates, and also provided a method for estimating certain thermophysical characteristics of such compounds without recourse to experimental measurements.

  11. SYNTHESIS AND IN VITRO CHARACTERIZATION OF HYDROXYPROPYL METHYLCELLULOSE-GRAFT-POLY (ACRYLIC ACID/2-ACRYLAMIDO-2-METHYL-1-PROPANESULFONIC ACID) POLYMERIC NETWORK FOR CONTROLLED RELEASE OF CAPTOPRIL.

    PubMed

    Furqan Muhammad, Iqbal; Mahmood, Ahmad; Aysha, Rashid

    2016-01-01

    A super-absorbent hydrogel was developed by crosslinking of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) and acrylic acid with hydroxypropyl methylcellulose (HPMC) for controlled release drug delivery of captopril, a well known antihypertensive drug. Acrylic acid and AMPS were polymerized and crosslinked with HPMC by free radical polymerization, a widely used chemical crosslinking method. N,N'-methylenebisacrylamide (MBA) and potassium persulfate (KPS) were added as cross-linker and initiator, respectively. The hydrogel formulation was loaded with captopril (as model drug). The concentration of captopril was monitored at 205 nm using UV spectrophotometer. Equilibrium swelling ratio was determined at pH 2, 4.5 and 7.4 to evaluate the pH responsiveness of the formed hydrogel. The super-absorbent hydrogels were evaluated by FTIR, SEM, XRD, and thermal analysis (DSC and TGA). The formation of new copolymeric network was determined by FTIR, XRD, TGA and DSC analysis. The hydrogel formulations with acrylic acid and AMPS ratio of 4: 1 and lower amounts of crosslinker had shown maximum swelling. Moreover, higher release rate of captopril was observed at pH 7.4 than at pH 2, because of more swelling capacity of copolymer with increasing pH of the aqueous medium. The present research work confirms the development of a stable hydrogel comprising of HPMC with acrylic acid and AMPS. The prepared hydrogels exhibited pH sensitive behav-ior. This superabsorbent composite prepared could be a successful drug carrier for treating hypertension. PMID:27008813

  12. Synthesis of hollow silver spheres using poly-(styrene-methyl acrylic acid) as templates in the presence of sodium polyacrylate

    NASA Astrophysics Data System (ADS)

    Wang, Aili; Yin, Hengbo; Ge, Chen; Ren, Min; Liu, Yumin; Jiang, Tingshun

    2010-02-01

    Hollow silver spheres were successfully prepared by reducing AgNO 3 with ascorbic acid and using negatively charged poly-(styrene-methyl acrylic acid) (PSA) spheres as templates in the presence of sodium polyacrylate as a stabilizer. Firstly, silver cations adsorbed on the surface of PSA spheres via electrostatic attraction between the carboxyl groups and silver cations were reduced in situ by ascorbic acid. The silver nanoparticles deposited on the surface of PSA spheres served as seeds for the further growth of silver shells. After that, extra amount of AgNO 3 and ascorbic acid solutions were added to form PSA/Ag composites with thick silver shells. In order to obtain compact silver shells, the as-prepared PSA/Ag composites were heated at 150 °C for 3 h. Then hollow silver spheres were prepared by dissolving PSA templates with tetrahydrofuran.

  13. Novel 6′-N-Aminoglycoside Acetyltransferase AAC(6′)-Iaj from a Clinical Isolate of Pseudomonas aeruginosa

    PubMed Central

    Tada, Tatsuya; Miyoshi-Akiyama, Tohru; Shimada, Kayo; Shimojima, Masahiro

    2013-01-01

    Pseudomonas aeruginosa NCGM1588 has a novel chromosomal class 1 integron, In151, which includes the aac(6′)-Iaj gene. The encoded protein, AAC(6′)-Iaj, was found to consist of 184 amino acids, with 70% identity to AAC(6′)-Ia. Escherichia coli transformed with a plasmid containing the aac(6′)-Iaj gene acquired resistance to all aminoglycosides tested except gentamicin. Of note, aac(6′)-Iaj contributed to the resistance to arbekacin. Thin-layer chromatography revealed that AAC(6′)-Iaj acetylated all aminoglycosides tested except gentamicin. These findings indicated that AAC(6′)-Iaj is a functional acetyltransferase that modifies the amino groups at the 6′ positions of aminoglycosides and contributes to aminoglycoside resistance of P. aeruginosa NCGM1588, including arbekacin. PMID:23070167

  14. Star-Shaped Polyacrylates: Highly Functionalized Architectures via CuAAC Click Conjugation.

    PubMed

    Lammens, Mieke; Fournier, David; Fijten, Martin W M; Hoogenboom, Richard; Prez, Filip Du

    2009-12-01

    Well-defined functional star-shaped polymer structures with up to 29 arms have been successfully synthesized by the combination of atom transfer radical polymerization (ATRP) and click chemistry. First, azide end-functionalized poly(isobornyl acrylate) (PiBA) star-shaped polymers were prepared by successive ATRP and bromine substitution. Subsequently, alkyne end-functionalized molecules and polymers were introduced onto the star-shaped PiBA bearing pendant azide moieties by copper-catalyzed azide-alkyne cycloaddition (CuAAC). The possibilities and limits for the CuAAC on such highly branched polyacrylates are described. PMID:21638494

  15. Poly(ethylene glycol)-co-methacrylamide-co-acrylic acid based nanogels for delivery of doxorubicin.

    PubMed

    Kumar, Parveen; Behl, Gautam; Sikka, Manisha; Chhikara, Aruna; Chopra, Madhu

    2016-10-01

    Polymeric nanogels have been widely explored for their potential application as delivery carriers for cancer therapeutics. The ability of nanogels to encapsulate therapeutics by simple diffusion mechanism and the ease of their fabrication to impart target specificity in addition to their ability to get internalized into target cells make them good candidates for drug delivery. The present study aims to investigate the applicability of poly(ethylene glycol)-co-methacrylamide-co-acrylic acid (PMA)-based nanogels as a viable option for the delivery of doxorubicin (DOX). The nanogels were synthesized by free radical polymerization in an inverse mini-emulsion and characterized by nuclear magnetic resonance spectroscopy ((1)H NMR), Fourier transform infrared spectroscopy, dynamic light scattering, transmission electron microscopy (TEM), X-ray diffraction and differential scanning calorimetry. DOX was physically incorporated into the nanogels (PMA-DOX) and the mechanism of its in vitro release was studied. TEM experiment revealed spherical morphology of nanogels and the hydrodynamic diameter of the neat nanogels was in the range of 160 ± 46.95 nm. The size of the nanogels increased from 235.1 ± 28.46 to 403.7 ± 89.89 nm with the increase in drug loading capacity from 4.68 ± 0.03 to 13.71 ± 0.01%. The sustained release of DOX was observed upto 80 h and the release rate decreased with increased loading capacity following anomalous release mechanism as indicated by the value of diffusion exponent (n = 0.64-0.75) obtained from Korsmeyer-Peppas equation. Further, cytotoxicity evaluation of PMA-DOX nanogels on HeLa cells resulted in relatively higher efficacy (IC50~5.88 μg/mL) as compared to free DOX (IC50~7.24 μg/mL) thus demonstrating that the preparation is potentially a promising drug delivery carrier. PMID:27383582

  16. Chemically Cross-Linked Poly(acrylic-co-vinylsulfonic) Acid Hydrogel for the Delivery of Isosorbide Mononitrate

    PubMed Central

    Ansari, Mahvash; Khan, Ikram Ullah

    2013-01-01

    We report synthesis, characterization, and drug release attributes of a series of novel pH-sensitive poly(acrylic-co-vinylsulfonic) acid hydrogels. These hydrogels were prepared by employing free radical polymerization using ethylene glycol dimethacrylate (EGDMA) and benzyl peroxide (BPO) as cross-linker and initiator, respectively. Effect of acrylic acid (AA), polyvinylsulfonic acid (PVSA), and EGDMA on prepared hydrogels was investigated. All formulations showed higher swelling at high pHs and vice versa. Formulations containing higher content of AA and EGDMA show reduced swelling, but one with higher content of PVSA showed increased swelling. Hydrogel network was characterized by determining structural parameters and loaded with isosorbide mononitrate. FTIR confirmed absence of drug polymer interaction while DSC and TGA demonstrated molecular dispersion of drug in a thermally stable polymeric network. All the hydrogel formulations exhibited a pH dependent release of isosorbide mononitrate which was found to be directly proportional to pH of the medium and PVSA content and inversely proportional to the AA contents. Drug release data were fitted to various kinetics models. Results indicated that release of isosorbide mononitrate from poly(AA-co-VSA) hydrogels was non-Fickian and that the mechanism was diffusion-controlled. PMID:24250265

  17. Poly (acrylic acid sodium) grafted carboxymethyl cellulose as a high performance polymer binder for silicon anode in lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Wei, Liangming; Chen, Changxin; Hou, Zhongyu; Wei, Hao

    2016-01-01

    The design of novel binder systems is required for the high capacity silicon (Si) anodes which usually undergo huge volume change during the charge/discharge cycling. Here, we introduce a poly (acrylic acid sodium)-grafted-carboxymethyl cellulose (NaPAA-g-CMC) copolymer as an excellent binder for Si anode in lithium ion batteries (LIBs). The NaPAA-g-CMC copolymer was prepared via a free radical graft polymerization method by using CMC and acrylic acid as precursors. Unlike the linear, one-dimensional binders, the NaPAA-g-CMC copolymer binder is expected to present multi-point interaction with Si surface, resulting in enhanced binding ability with Si particles as well as with the copper (Cu) current collectors, and building a stable solid electrolyte interface (SEI) layer on the Si surface. The NaPAA-g-CMC based Si anode shows much better cycle stability and higher coulombic efficiency than those made with the well-known linear polymeric binders such as CMC and NaPPA.

  18. Poly (acrylic acid sodium) grafted carboxymethyl cellulose as a high performance polymer binder for silicon anode in lithium ion batteries.

    PubMed

    Wei, Liangming; Chen, Changxin; Hou, Zhongyu; Wei, Hao

    2016-01-01

    The design of novel binder systems is required for the high capacity silicon (Si) anodes which usually undergo huge volume change during the charge/discharge cycling. Here, we introduce a poly (acrylic acid sodium)-grafted-carboxymethyl cellulose (NaPAA-g-CMC) copolymer as an excellent binder for Si anode in lithium ion batteries (LIBs). The NaPAA-g-CMC copolymer was prepared via a free radical graft polymerization method by using CMC and acrylic acid as precursors. Unlike the linear, one-dimensional binders, the NaPAA-g-CMC copolymer binder is expected to present multi-point interaction with Si surface, resulting in enhanced binding ability with Si particles as well as with the copper (Cu) current collectors, and building a stable solid electrolyte interface (SEI) layer on the Si surface. The NaPAA-g-CMC based Si anode shows much better cycle stability and higher coulombic efficiency than those made with the well-known linear polymeric binders such as CMC and NaPPA. PMID:26786315

  19. Poly (acrylic acid sodium) grafted carboxymethyl cellulose as a high performance polymer binder for silicon anode in lithium ion batteries

    PubMed Central

    Wei, Liangming; Chen, Changxin; Hou, Zhongyu; Wei, Hao

    2016-01-01

    The design of novel binder systems is required for the high capacity silicon (Si) anodes which usually undergo huge volume change during the charge/discharge cycling. Here, we introduce a poly (acrylic acid sodium)-grafted-carboxymethyl cellulose (NaPAA-g-CMC) copolymer as an excellent binder for Si anode in lithium ion batteries (LIBs). The NaPAA-g-CMC copolymer was prepared via a free radical graft polymerization method by using CMC and acrylic acid as precursors. Unlike the linear, one-dimensional binders, the NaPAA-g-CMC copolymer binder is expected to present multi-point interaction with Si surface, resulting in enhanced binding ability with Si particles as well as with the copper (Cu) current collectors, and building a stable solid electrolyte interface (SEI) layer on the Si surface. The NaPAA-g-CMC based Si anode shows much better cycle stability and higher coulombic efficiency than those made with the well-known linear polymeric binders such as CMC and NaPPA. PMID:26786315

  20. Thermoresponsive hyperbranched copolymer with multi acrylate functionality for in situ cross-linkable hyaluronic acid composite semi-IPN hydrogel.

    PubMed

    Dong, Yixiao; Hassan, Waqar; Zheng, Yu; Saeed, Aram Omer; Cao, Hongliang; Tai, Hongyun; Pandit, Abhay; Wang, Wenxin

    2012-01-01

    Thermoresponsive polymers have been widely used for in situ formed hydrogels in drug delivery and tissue engineering as they are easy to handle and their shape can easily conform to tissue defects. However, non-covalent bonding and mechanical weakness of these hydrogels limit their applications. In this study, a physically and chemically in situ cross-linkable hydrogel system was developed from a novel thermoresponsive hyperbranched PEG based copolymer with multi acrylate functionality, which was synthesized via an 'one pot and one step' in situ deactivation enhanced atom transfer radical co-polymerization of poly(ethylene glycol) diacrylate (PEGDA, M(n) = 258 g mol(-1)), poly(ethylene glycol) methyl ether methacrylate (PEGMEMA, M(n )= 475 g mol(-1)) and (2-methoxyethoxy) ethyl methacrylate (MEO(2)MA). This hyperbranched copolymer was tailored to have the lower critical solution temperature to form physical gelation around 37°C. Meanwhile, with high level of acrylate functionalities, a chemically cross-linked gel was formed from this copolymer using thiol functional cross-linker of pentaerythritol tetrakis (3-mercaptopropionate) (QT) via thiol-ene Michael addition reaction. Furthermore, a semi-interpenetrated polymer networks (semi-IPN) structure was developed by combining this polymer with hyaluronic acid (HA), leading to an in situ cross-linkable hydrogel with significantly increased porosity, enhanced swelling behavior and improved cell adhesion and viability both in 2D and 3D cell culture models. PMID:22143908

  1. Flame retardant brominated styrene-based polymers. V. Synthesis and characterization of dibromostyrene and butyl acrylate latices with and without itaconic acid

    SciTech Connect

    Wang, J.L.; Favstritsky, N.A.; Hemmerly, D.M.

    1995-12-01

    Dibranostyrene and butyl acrylate lattices with and without itaconic acid having desirable physical properties in combination with flame retardancy are prepared by an emulsion polymerization techniques Both lattices were characterized in terms of glass transition temperature (Tg), residual monomer, solids, Brookfield viscosity, UV stability and flame retardancy.

  2. 40 CFR 721.10526 - 2-Propenoic acid, 2-methyl-, 2-hydroxyethyl ester, telomers with C18-26-alkyl acrylate, 1...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false 2-Propenoic acid, 2-methyl-, 2-hydroxyethyl ester, telomers with C18-26-alkyl acrylate, 1-dodecanethiol, N-(hydroxymethyl)-2-methyl-2-propenamide, polyfluorooctyl methacrylate and vinylidene chloride, 2,2'- hydrochloride (1:2)-initiated (generic). 721.10526 Section 721.10526...

  3. 40 CFR 721.10526 - 2-Propenoic acid, 2-methyl-, 2-hydroxyethyl ester, telomers with C18-26-alkyl acrylate, 1...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false 2-Propenoic acid, 2-methyl-, 2-hydroxyethyl ester, telomers with C18-26-alkyl acrylate, 1-dodecanethiol, N-(hydroxymethyl)-2-methyl-2-propenamide, polyfluorooctyl methacrylate and vinylidene chloride, 2,2'- hydrochloride (1:2)-initiated (generic). 721.10526 Section 721.10526...

  4. A new coordination mode of (E)-3-(3-hydroxyl-phenyl)-acrylic acid in copper complex: Crystal structure and magnetic properties

    SciTech Connect

    Jin, Xin; Zhou, Pei; Zheng, Chunying; Li, Hui

    2015-05-15

    A copper complex ([Cu(py){sub 2}(L){sub 2}]·2CH{sub 3}OH){sub n} (HL=(E)-3-(3-hydroxyl-phenyl)-acrylic acid) (1) with acrylic acid ligand was synthesized and structurally analyzed by IR, elemental analysis, TGA and the single-crystal X-ray diffraction methods. It is the first time to find that phenolic hydroxyl of L coordinates to Cu(II). Complex 1 exhibits 1D chain by a double-bridge of ligands, and the 3D supramolecular framework in complex 1 is constructed by π–π stacking interactions and van der Waals Contacts among the 1D chains. The magnetic properties of complex 1 have been studied. - Graphical abstract: A copper complex based on (E)-3-(3-hydroxyl-phenyl)-acrylic acid in a novel coordinated way was synthesized and a ferromagnetic exchange interactions between neighboring Cu(II) ions has be achieved. - Highlights: • A new copper complex with acrylic acid ligand was synthesized and analyzed. • We find the phenolic hydroxyl of MCA ligand coordinates to metal ion firstly. • A ferromagnetic exchange interactions between Cu(II) ions has been achieved.

  5. Synthesis of perm-selective membranes by grafting acrylic acid into air-irradiated Teflon-FEP films

    NASA Astrophysics Data System (ADS)

    Bozzi, Annick; Chapiro, Adolphe

    Grafting acrylic acid into air-irradiated Teflon-FEP films was investigated. Pre-irradiation doses ranged from 0.5 to 10 kGy. Grafting occurred at 45 or 60°C. Homopolymerization inhibitors, ferrous ions or methylene blue, were added to the system. It was found that after completion of the reaction, within 40-100 min, membranes were obtained with very low electric resistivities. The influence of added inhibitors, pre-irradiation dose and grafting temperature was studied. From the results it is concluded that the initiating centers in air-irradiated Teflon-FEP are, on the one hand, peroxides of structure POOP', in which P is a polymeric radical and Pprime; a small fragment, and on the other trapped PO .2 radicals. The latter only react after losing their oxygen. In the presence of polymerization inhibitors, initiation involves a redox process which reduces the overall activation energy.

  6. Removal of reactive dyes from textile wastewater by immobilized chitosan upon grafted Jute fibers with acrylic acid by gamma irradiation

    NASA Astrophysics Data System (ADS)

    Hassan, Mahmoud S.

    2015-10-01

    Jute fibers were grafted with acrylic acid by gamma irradiation technique. Chitosan was immobilized upon the grafted Jute fibers to be used as an adsorbent for waste reactive dye. The treated Jute fibers were characterized by using of Fourier-transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effect of Jute treatment on its thermal stability by using thermogravimetric analysis (TGA) and its mechanical properties were investigated. The adsorption isotherm and the different factors affecting the dye adsorption such as pH and contact time were also studied. It was found that the dye adsorption was enhanced in the low pH range and increased with increasing of the contact time, regardless of temperature change.

  7. Complex Formation Between Lysozyme and Stabilized Micelles with a Mixed Poly(ethylene oxide)/Poly(acrylic acid) Shell.

    PubMed

    Karayianni, Maria; Gancheva, Valeria; Pispas, Stergios; Petrov, Petar

    2016-03-10

    The electrostatic complexation between lysozyme and stabilized polymeric micelles (SPMs) with a poly(acrylic acid) (PAA) or a mixed poly(ethylene oxide)/poly(acrylic acid) (PEO/PAA) shell (SPMs with a mixed shell, SPMMS) and a temperature-responsive poly(propylene oxide) (PPO) core was investigated by means of dynamic, static, and electrophoretic light scattering. The SPMs and different types of SPMMS used resulted from the self-assembly of PAA-PPO-PAA triblock copolymer chains, or PAA-PPO-PAA and PEO-PPO-PEO triblock copolymer chain mixtures (with varying chain lengths and molar ratios) in aqueous solutions at pH 10 and the subsequent cross-linking of their PPO cores via loading and photo-cross-linking of pentaerythritol tetraacrylate (PETA). The solution behavior, structure and properties of the formed complexes at pH 7 and 0.01 M ionic strength, were studied as a function of the protein concentration in the solution (the concentration of the stabilized micelles was kept constant) or equivalently the ratio of the two components. The complexation process and properties of the complexes proved to be dependent on the protein concentration, while of particular interest was the effect of the structure of the shell of the SPMs on the stability/solubility of the complexes. Finally, the fluorescence and mid infrared spectroscopic investigation of the structure of the complexed protein showed that, although a small stretching of the protein molecules occurred in some cases, no protein denaturation takes place upon complexation. PMID:26881445

  8. Calcium Phosphate Mineralization in Cellulose Derivative/Poly(acrylic acid) Composites Having a Chiral Nematic Mesomorphic Structure.

    PubMed

    Ogiwara, Takuya; Katsumura, Ayaka; Sugimura, Kazuki; Teramoto, Yoshikuni; Nishio, Yoshiyuki

    2015-12-14

    Calcium phosphate mineralization was conducted by using polymer composites of liquid-crystalline (ethyl)cellulose (EC) or (hydroxypropyl)cellulose (HPC) with poly(acrylic acid) (PAA) as a scaffolding medium for the inorganic deposition. The EC/PAA and HPC/PAA samples were prepared in colored film form from EC and HPC lyotropic liquid crystals of left-handed and right-handed chiral nematics, respectively, by polymerization and cross-linking of acrylic acid as the main solvent component. The mineralization was allowed to proceed in a batchwise operation by soaking the liquid-crystalline films in an aqueous salt solution containing the relevant ions, Ca(2+) and HPO4(2-). The calcium phosphate-deposited EC/PAA and HPC/PAA composites (weight gain, typically 15-25% and 6-11%, respectively) retained the chiral nematic organization of the respective original handedness but exhibited selective light-reflection of longer wavelengths relative to that of the corresponding nonmineralized samples. From X-ray diffraction and energy-dispersive X-ray spectroscopy measurements, it was deduced that the calcium and phosphorus were incorporated inside the polymer matrices in three forms: amorphous calcium phosphate, hydroxyapatite, and a certain complex of PAA-Ca(2+). Dynamic mechanical analysis and thermogravimetry revealed that the inorganic hybridization remarkably enhanced the thermal and mechanical performance of the optically functionalized cellulosic/synthetic polymer composites; however, the effect was more drastic in the EC/PAA series rather than the HPC/PAA series, reflecting the difference in the deposited mineral amount between the two. PMID:26536381

  9. Preparation and evaluation of MRI detectable poly (acrylic acid) microspheres loaded with superparamagnetic iron oxide nanoparticles for transcatheter arterial embolization.

    PubMed

    Wang, Huan; Qin, Xiao-Ya; Li, Zi-Yuan; Guo, Li-Ying; Zheng, Zhuo-Zhao; Liu, Li-Si; Fan, Tian-Yuan

    2016-09-25

    To monitor the spatial distribution of embolic particles inside the target tissues during and after embolization, blank poly (acrylic acid) microspheres (PMs) were initially prepared by inverse suspension polymerization method and then loaded with superparamagnetic iron oxide (SPIO) nanoparticles by in situ precipitation method to obtain magnetic resonance imaging (MRI) detectable SPIO-loaded poly (acrylic acid) microspheres (SPMs). The loading of SPIO nanoparticles in SPMs was confirmed by vibrating sample magnetometer, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and infrared spectrum, respectively. The results showed that SPMs exhibited excellent superparamagnetism and the SPIO embedded in SPMs were proved to be inverse spinel magnetite. The content of SPIO loaded in wet SPMs of subgroups of 100-300, 300-500, 500-700 and 700-900μm was measured to be 11.84±0.07, 10.20±0.05, 9.98±0.00 and 8.79±0.01mg/ml, corresponding to the weight percentage in freeze-dried SPMs to be 18.07±0.28%, 18.54±0.13%, 18.66±0.01% and 18.50±0.07%, respectively. The SPMs were spherical in shape, had smooth surface, and were within the size range of clinical demands for embolization. The compression tests indicated that SPMs were more rigid than PMs and commercially used Embospheres (P<0.01). The MRI detectability of SPMs was evaluated with the SPMs embedded in gel phantom in vitro and injected subcutaneously into the back of mice in vivo. Both the results demonstrated that the SPMs could provide distinct negative contrast enhancement and be sensitively detected by T2-weighted MR imaging. All the results show that SPMs are potential MRI detectable embolic microspheres for the future embolotherapy. PMID:27426106

  10. Identification of a novel 6'-N-aminoglycoside acetyltransferase, AAC(6')-Iak, from a multidrug-resistant clinical isolate of Stenotrophomonas maltophilia.

    PubMed

    Tada, Tatsuya; Miyoshi-Akiyama, Tohru; Dahal, Rajan K; Mishra, Shyam K; Shimada, Kayo; Ohara, Hiroshi; Kirikae, Teruo; Pokhrel, Bharat M

    2014-10-01

    Stenotrophomonas maltophilia IOMTU250 has a novel 6'-N-aminoglycoside acetyltransferase-encoding gene, aac(6')-Iak. The encoded protein, AAC(6')-Iak, consists of 153 amino acids and has 86.3% identity to AAC(6')-Iz. Escherichia coli transformed with a plasmid containing aac(6')-Iak exhibited decreased susceptibility to arbekacin, dibekacin, neomycin, netilmicin, sisomicin, and tobramycin. Thin-layer chromatography showed that AAC(6')-Iak acetylated amikacin, arbekacin, dibekacin, isepamicin, kanamycin, neomycin, netilmicin, sisomicin, and tobramycin but not apramycin, gentamicin, or lividomycin. PMID:25092711

  11. Synthesis and characterization of multi-responsive poly (NIPAm-co-AAc) microgels

    NASA Astrophysics Data System (ADS)

    Haider, Irfan; Siddiq, Mohammad; Mujtaba Shah, Syed; Rehman, Saif ur

    2014-06-01

    Two samples of multi-responsive copolymer microgels, poly(N-isopropylacrylamide-co-acrylic acid) [P(NIPAm-co-AAc)], were synthesized by emulsion polymerization using different amounts of emulsifier. The unreacted monomers and surfactant were removed from the microgels by dialysis. Dynamic Laser Light Scattering (DLS) was used to determine the diffusion coefficient and hydrodynamic radius (Rh) of the microgels at different pH values and temperatures. At pH 7 the microgel showed rapid response to temperature and underwent volume phase transition (VPT) as the temperature was raised. At lower temperature the microgels were in the hydrated or swollen state but beyond 38oC, the size was abruptly decreased. Under different conditions of pH and NaCl concentrations, variations in VPTT values were noticed. By increasing pH the VPTT was increased but the addition of salt had an inverse effect. The weight average molar mass (Mw) and radius of gyration (Rg) were measured by Static Laser Light Scattering (SLS). FTIR spectroscopy was used to confirm the chemical structures of microgels

  12. Behavior of Surface-Anchored Poly(acrylic acid) Brushes with Grafting Density Gradients on Solid Substrates: 1. Experiment

    SciTech Connect

    Wu,T.; Gong, P.; Szleifer, I.; Vicek, P.; Subr, V.; Genzer, J.

    2007-01-01

    We describe experiments pertaining to the formation of surface-anchored poly(acrylic acid) (PAA) brushes with a gradual variation of the PAA grafting densities on flat surfaces and provide detailed analysis of their properties. The PAA brush gradients are generated by first covering the substrate with a molecular gradient of the polymerization initiator, followed by the 'grafting from' polymerization of tert-butyl acrylate (tBA) from these substrate-bound initiator centers, and finally converting the PtBA into PAA. We use spectroscopic ellipsometry to measure the wet thickness of the grafted PAA chains in aqueous solutions at three different pH values (4, 5.8, and 10) and a series of ionic strengths (IS). Our measurements reveal that at low grafting densities, s, the wet thickness of the PAA brush (H) remains relatively constant, the polymers are in the mushroom regime. Beyond a certain value of s, the macromolecules enter the brush regime, where H increases with increasing s. For a given s, H exhibits a nonmonotonic behavior as a function of the IS. At large IS, the H is small because the charges along PAA are completely screened by the excess of the external salt. As IS decreases, the PAA enters the so-called salt brush (SB) regime, where H increases. At a certain value of IS, H reaches a maximum and then decreases again. The latter is a typical brush behavior in so-called osmotic brush (OB) regime. We provide detailed discussion of the behavior of the grafted PAA chains in the SB and OB regimes.

  13. Mechanical properties of a waterborne pressure-sensitive adhesive with a percolating poly(acrylic acid)-based diblock copolymer network: effect of pH.

    PubMed

    Gurney, Robert S; Morse, Andrew; Siband, Elodie; Dupin, Damien; Armes, Steven P; Keddie, Joseph L

    2015-06-15

    Copolymerizing an acrylic acid comonomer is often beneficial for the adhesive properties of waterborne pressure-sensitive adhesives (PSAs). Here, we demonstrate a new strategy in which poly(acrylic acid) (PAA) is distributed as a percolating network within a PSA film formed from a polymer colloid. A diblock copolymer composed of PAA and poly(n-butyl acrylate) (PBA) blocks was synthesized using reversible addition-fragmentation chain transfer (RAFT) polymerization and adsorbed onto soft acrylic latex particles prior to their film formation. The thin adsorbed shells on the particles create a percolating network that raises the elastic modulus, creep resistance and tensile strength of the final film. When the film formation occurs at pH 10, ionomeric crosslinking occurs, and high tack adhesion is obtained in combination with high creep resistance. The results show that the addition of an amphiphilic PAA-b-PBA diblock copolymer (2.0 wt.%) to a soft latex provides a simple yet effective means of adjusting the mechanical and adhesive properties of the resulting composite film. PMID:25706199

  14. Fluorescent Ag nanoclusters prepared in aqueous poly(acrylic acid-co-maleic acid) solutions: a spectroscopic study of their excited state dynamics, size and local environment.

    PubMed

    Dandapat, Manika; Mandal, Debabrata

    2016-01-28

    Stable, fluorescent Ag nanoclusters were prepared in aqueous solutions of Na(+) salt of the carboxylate-rich polymer poly(acrylic acid-co-maleic acid) under brief spells of UV irradiation. The nanoclusters were nearly spherical, with diameters within 1.90 ± 0.50 nm, but displayed a prominent red edge excitation shift (REES) of fluorescence upon exciting within the visible absorption band, indicating heterogeneity of energy level distributions. Spectroscopic studies revealed that irrespective of whether the nanoclusters are excited in their UV or visible absorption bands, their fluorescence always ensues from the same manifold of emissive states, with a broad range of fluorescence lifetimes from ∼150 fs to 1 ns. PMID:26700465

  15. Chemical crosslinking of acrylic acid to form biocompatible pH sensitive hydrogel reinforced with cellulose nanocrystals (CNC)

    SciTech Connect

    Lim, Lim Sze; Ahmad, Ishak; Lazim, Mohd Azwani Shah Mat; Amin, Mohd. Cairul Iqbal Mohd

    2014-09-03

    The purpose of this study is to produce a novel pH and temperature sensitive hydrogel, composed of poly(acrylic acid) (PAA) and cellulose nanocrystal (CNC). CNC was extracted from kenaf fiber through a series of alkali and bleaching treatments followed by acid hydrolysis. The PAA was then subjected to chemical cross-linking using the cross-linking agent (N,N-methylenebisacrylamide) with CNC entrapped in PAA matrix. The mixture was casted onto petri dish to obtain disc shape hydrogel. The effects of reaction conditions such as the ratio of PAA and CNC on the swelling behavior of the hydrogel obtained towards pH and temperature were studied. The obtained hydrogel was further subjected to different tests such swelling test for swelling behaviour at different pH and temperature along with scanning electron microscopy (SEM) for morphology analysis. The hydrogel obtained showed excellent pH sensitivity and obtained maximum swelling at pH 7. Besides that, hydrogel obtained showed significant increase in swelling ratio when temperature of swelling medium was increased from 25°C to 37°C. SEM micrograph showed that the pore size of the hydrogel decreases with increase of CNC content proving that the hydrogel structure became more rigid with addition of CNC. The PAA/CNC hydrogel with such excellent sensitivity towards pH and temperature can be developed further as drug carrier.

  16. Chemical crosslinking of acrylic acid to form biocompatible pH sensitive hydrogel reinforced with cellulose nanocrystals (CNC)

    NASA Astrophysics Data System (ADS)

    Lim, Lim Sze; Ahmad, Ishak; Lazim, Mohd Azwani Shah Mat; Amin, Mohd. Cairul Iqbal Mohd

    2014-09-01

    The purpose of this study is to produce a novel pH and temperature sensitive hydrogel, composed of poly(acrylic acid) (PAA) and cellulose nanocrystal (CNC). CNC was extracted from kenaf fiber through a series of alkali and bleaching treatments followed by acid hydrolysis. The PAA was then subjected to chemical cross-linking using the cross-linking agent (N,N-methylenebisacrylamide) with CNC entrapped in PAA matrix. The mixture was casted onto petri dish to obtain disc shape hydrogel. The effects of reaction conditions such as the ratio of PAA and CNC on the swelling behavior of the hydrogel obtained towards pH and temperature were studied. The obtained hydrogel was further subjected to different tests such swelling test for swelling behaviour at different pH and temperature along with scanning electron microscopy (SEM) for morphology analysis. The hydrogel obtained showed excellent pH sensitivity and obtained maximum swelling at pH 7. Besides that, hydrogel obtained showed significant increase in swelling ratio when temperature of swelling medium was increased from 25°C to 37°C. SEM micrograph showed that the pore size of the hydrogel decreases with increase of CNC content proving that the hydrogel structure became more rigid with addition of CNC. The PAA/CNC hydrogel with such excellent sensitivity towards pH and temperature can be developed further as drug carrier.

  17. Mechanism of poly(acrylic acid) acceleration of antithrombin inhibition of thrombin: implications for the design of novel heparin mimics.

    PubMed

    Monien, Bernhard H; Cheang, Kai I; Desai, Umesh R

    2005-08-11

    The bridging mechanism of antithrombin inhibition of thrombin is a dominant mechanism contributing a massive approximately 2500-fold acceleration in the reaction rate and is also a key reason for the clinical usage of heparin. Our recent study of the antithrombin-activating properties of a carboxylic acid-based polymer, poly(acrylic acid) (PAA), demonstrated a surprisingly high acceleration in thrombin inhibition (Monien, B. H.; Desai, U. R. J. Med. Chem. 2005, 48, 1269). To better understand this interesting phenomenon, we have studied the mechanism of PAA-dependent acceleration in antithrombin inhibition of thrombin. Competitive binding studies with low-affinity heparin and a heparin tetrasaccharide suggest that PAA binds antithrombin in both the pentasaccharide- and the extended heparin-binding sites, and these results are corroborated by molecular modeling. The salt-dependence of the K(D) of the PAA-antithrombin interaction shows the formation of five ionic interactions. In contrast, the contribution of nonionic forces is miniscule, resulting in an interaction that is significantly weaker than that observed for heparins. A bell-shaped profile of the observed rate constant for antithrombin inhibition of thrombin as a function of PAA concentration was observed, suggesting that inhibition proceeds through the "bridging" mechanism. The knowledge gained in this mechanistic study highlights important rules for the rational design of orally available heparin mimics. PMID:16078853

  18. Poly(acrylic acid)/polyethylene glycol hygrogel prepared by using gamma-ray irradiation for mucosa adhesion

    NASA Astrophysics Data System (ADS)

    Nho, Young-Chang; Park, Jong-Seok; Shin, Jung-Woong; Lim, Youn-Mook; Jeong, Sung-In; Shin, Young-Min; Gwon, Hui-Jeong; Khil, Myung-Seob; Lee, Deok-Won; Ahn, Sung-Jun

    2015-01-01

    A buccal delivery system provides a much milder environment for drug delivery compared to an oral delivery which presents a hostile environment for drugs, especially proteins and polypeptides, owing to acid hydrolysis. Local delivery in an oral cavity has particular applications in the treatment of toothaches, periodontal disease, and bacterial infections. Poly(acrylic acid) (PAA)-based hydrogels prepared using a chemical initiator have been attempted for a mucoadhesive system owing to their flexibility and excellent bioadhesion. In this experiment, PAA and polyethylene glycol (PEG) were selected to prepare using a radiation process a bioadhesive hydrogel for adhesion to mucosal surfaces. PAA and PEG were dissolved in purified water to prepare a homogeneous PAA/PEG solution, and the solution was then irradiated using an electron beam at dose up to 70 kGy to make the hydrogels. Their physical properties, such as gel percent, swelling percent, and adhesive strength to mucosal surfaces, were investigated. In this experiment, various amounts of PEG were incorporated into the PAA to enhance the mucoadhesive property of the hydrogels. The effect of the molecular weight of PEG on the mucoadhesion was also examined.

  19. Rheology and interfacial properties of aqueous solutions of the diblock polyelectrolyte poly(styrene-block-acrylic acid)

    NASA Astrophysics Data System (ADS)

    Kimerling, Abigail

    In aqueous solutions diblock polyelectrolytes with amphiphilic character form aggregate structures, which affect physical properties such as viscosity, elasticity, surface tension, and film hydrophilicity. Potential applications for diblock polyelectrolyte solutions include coatings, inks, oil recovery agents, personal care products, and biomaterials. By varying the diblock polyelectrolyte and solution properties, the solutions can be tuned to meet the needs of particular applications. The research objective was to identify the influences of block length, pH, and ionic strength on the rheological and interfacial properties of poly(styrene- b-acrylic acid) (PS-PAA) solutions. Six polymers with varied PS and PAA block lengths were examined, all at 1.0 wt% in aqueous solutions. The hydrophobicity of the PS block causes the formation of spherical micelles in aqueous solutions. Increasing the solution pH ionizes the PAA block, which leads to an increase in micelle corona thickness due to repulsions between chains. Major trends observed in the rheological and interfacial properties can be understood in terms of expected changes in the micelle size and interfacial self-assembly with pH, ionic strength, and block length. Addition of NaOH was found to increase the solution pH and initially led to increases in solution viscosity, elasticity, surface tension, and film hydrophilicity. This effect was attributed to creation of larger micelles and greater inter-micellar repulsions as the PAA chain became more fully charged. However, when the concentration of NaOH exceeded a critical value, the solution viscosity, elasticity, and film hydrophilicity decreased. It is believed this was due to charge shielding by excess sodium ions, leading to shrinkage of the micelle corona and smaller micelles. Increasing the PS-PAA solution ionic strength by adding NaCl also provided charge shielding, as observed by decreases in solution viscosity and elasticity. Increasing the length of either

  20. Copper catalysed azide-alkyne cycloaddition (CuAAC) in liquid ammonia.

    PubMed

    Ji, Pengju; Atherton, John H; Page, Michael I

    2012-10-21

    Copper(I) catalysed azide-alkyne cycloaddition reactions (CuAAC) occur smoothly in liquid ammonia (LNH(3)) at room temperature to give exclusively 1,4-substituted 1,2,3-triazoles with excellent yields (up to 99%). The CuAAC reactions in liquid ammonia require relatively small amounts of copper(I) catalyst (0.5 mole%) compared with that in conventional solvents. The product can be obtained conveniently by simply evaporation of ammonia, indicating its potential application in industry. The rate of the CuAAC reaction in liquid ammonia shows a second order dependence on the copper(I) concentration and the reaction occurs only with terminal alkynes. Deuterium exchange experiments with phenyl acetylene-d(1) show that the acidity of the alkyne is increased at least 1000-fold with catalytic amounts of copper(I) in liquid ammonia. The mechanism of the CuAAC reaction in liquid ammonia is discussed. PMID:22930181

  1. Preparation and optical properties of CdS nanoparticles dispersed in poly(2-(dimethylamino)ethyl methacrylate-co-acrylic acid) co-polymers

    NASA Astrophysics Data System (ADS)

    Trandafilović, L. V.; Djoković, V.; Bibić, N.; Georges, M. K.; Radhakrishnan, T.

    2008-03-01

    CdS/poly(2-(dimethylamino)ethyl methacrylate-co-acrylic acid) nanocomposites were prepared and characterized using structural, optical and thermal methods. Co-polymers used as the matrices were synthesized by radical polymerization of the co-monomers in different mol ratios (1:1, 2:1 and 1:2, DMAEMA:acrylic acid). The presence of the nanostructured CdS was confirmed by TEM analysis as well as by the shift of the onset of the optical absorption towards lower wavelengths. XRD spectra showed the cubic crystal phase of the obtained CdS nanoparticles. TGA measurements revealed improved thermal stability of the nanocomposite with respect to pure co-polymer matrix.

  2. AAC Team Perceptions: Augmentative and Alternative Communication Device Use

    ERIC Educational Resources Information Center

    Bailey, Rita L.; Stoner, Julie B.; Parette, Howard P., Jr.; Angell, Maureen E.

    2006-01-01

    This study provided an in-depth view of augmentative and alternative (AAC) team member's perceptions of AAC device use with older students. Six special education teachers and one speech-language pathologist (SLP) who worked as members of an AAC team were interviewed to determine their perceptions of AAC use in junior high and high school settings.…

  3. Characterization and antimicrobial property of poly(acrylic acid) nanogel containing silver particle prepared by electron beam.

    PubMed

    Choi, Jong-Bae; Park, Jong-Seok; Khil, Myung-Seob; Gwon, Hui-Jeong; Lim, Youn-Mook; Jeong, Sung-In; Shin, Young-Min; Nho, Young-Chang

    2013-01-01

    In this study, we developed a one step process to synthesize nanogel containing silver nanoparticles involving electron beam irradiation. Water-soluble silver nitrate powder is dissolved in the distilled water and then poly(acrylic acid) (PAAc) and hexane are put into this silver nitrate solution. These samples are irradiated by an electron beam to make the PAAc nanogels containing silver nanoparticles (Ag/PAAc nanogels). The nanoparticles were characterized by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). In addition, the particle size and zeta-potential were confirmed by a particle size analyzer (PSA). The antibacterial properties of the nanogels were evaluated by paper diffusion test. The Ag/PAAc nanogels had an antibacterial effect against Escherichia coli and Staphylococcus aureus. The nanogels also demonstrated a good healing effect against diabetic ulcer. The size of the Ag/PAAc nanogels decreased with increasing irradiation doses, and the absolute value of the zeta potential increased with increasing irradiation doses. Also, the Ag/PAAc nanogels exhibited good antibacterial activity against both Gram-negative and Gram-positive bacteria. In in vivo wound healing, the Ag/PAAc nanogels have a good healing effect. PMID:23708101

  4. Ultrasensitive electrochemical immunosensor based on horseradish peroxidase (HRP)-loaded silica-poly(acrylic acid) brushes for protein biomarker detection.

    PubMed

    Zhao, Yan; Zheng, Yiqun; Kong, Rongmei; Xia, Lian; Qu, Fengli

    2016-01-15

    We report an ultrasensitive electrochemical immunosensor designed for the detection of protein biomarkers using horseradish peroxidase (HRP)-loaded silica-poly(acrylic acid) brushes (SiO2-SPAABs) as labels. HRP could be efficiently and stably accommodated in the three-dimensional architecture of the SiO2-SPAABs and the SiO2-SPAABs-HRP exhibited high catalytic performance towards o-phenylenediamine (OPD) oxidation in the presence of H2O2, which resulted in significant differential pulse voltammetric (DPV) response change and color change. Using human IgG (HIgG) as a model analyte, a sandwich-type immunosensor was constructed. In particular, graphene oxide (GO) and SiO2-SPAABs-HRP were used to immobilize capture antibody (Ab1) and bind a layer of detection antibody (Ab2), respectively. The current biosensor exhibited a good linear response of HIgG from 100pg/mL to 100μg/mL with a detection limit of 50pg/mL (S/N=5). The sensitivity was 6.70-fold higher than the conventional enzyme-linked immunosorbent assays. The immunosensor results were validated through the detection of HIgG in serum samples. PMID:26342574

  5. Biodegradability and mechanical properties of poly(butylene succinate) composites with finely dispersed hydrophilic poly(acrylic acid)

    NASA Astrophysics Data System (ADS)

    Mizuno, Sawako; Hotta, Atsushi

    2014-03-01

    Biodegradability and mechanical properties of aliphatic poly(butylene succinate) (PBS) films with finely dispersed hydrophilic poly(acrylic acid) (PAA) were investigated. First, 3.5 wt% of PAA was chemically grafted onto the surface of the PBS films (surface-grafted PBS) by photo grafting polymerization, and then the grafted PAA was homogeneously and finely dispersed into PBS by dissolving the surface-grafted PBS into chloroform before mixing and drying to get solid PAA-dispersed PBS. Degradation of these modified PBS was investigated using gel permeation chromatography (GPC) and tensile testing. According to the GPC results, it was found that the PAA-dispersed PBS had intermediate biodegradability with the intermediate water intake, and the reaction constant of PAA-dispersed PBS was in between those of untreated PBS and surface-grafted PBS, in fact 25% higher and 17% lower, respectively. The experimental results presented that the biodegradability of PBS could be well controlled by the dispersion of PAA, possibly leading to the widespread use of PBS for biodegradable polymers.

  6. Preparation of mesoporous poly (acrylic acid)/SiO2 composite nanofiber membranes having adsorption capacity for indigo carmine dye

    NASA Astrophysics Data System (ADS)

    Xu, Ran; Jia, Min; Li, Fengting; Wang, Hongtao; Zhang, Bingru; Qiao, Junlian

    2012-03-01

    Mesoporous poly (acrylic acid)/SiO2 (PAA/SiO2) composite nanofiber membranes functionalized with mercapto groups were fabricated by a sol-gel electrospinning method, and their adsorption capacity for indigo carmine was investigated. The membranes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, x-ray powder diffraction (XRD), and nitrogen adsorption-desorption measurement. SEM and TEM observation results showed that the PAA/SiO2 fibers had diameters between 400-800 nm and mesopores with an average pore size of 3.88 nm. The specific surface area of the mesoporous nanofiber membranes was 514.89 m2/g. The characteristic peaks for mercapto group vibration in FTIR and Raman spectra demonstrated that the mercapto groups have been incorporated into the silica skeleton. The adsorption isotherm data of indigo carmine on the membranes fit well with Redlich-Peterson model, and the maximum adsorption capacity calculated was 523.11 mg/g. It was found that the removal rate of indigo carmine by the membranes reached a maximum of 98% in 90 min and the adsorption kinetics followed a pseudo-second-order model. The high adsorption capacity of PAA/SiO2 nanofiber membrane makes it a promising adsorbent for indigo carmine removal from the wastewater.

  7. Biocompatibility of poly(ethylene glycol) and poly(acrylic acid) interpenetrating network hydrogel by intrastromal implantation in rabbit cornea.

    PubMed

    Zheng, Luo Luo; Vanchinathan, Vijay; Dalal, Roopa; Noolandi, Jaan; Waters, Dale J; Hartmann, Laura; Cochran, Jennifer R; Frank, Curtis W; Yu, Charles Q; Ta, Christopher N

    2015-10-01

    We evaluated the biocompatibility of a poly(ethylene glycol) and poly(acrylic acid) (PEG/PAA) interpenetrating network hydrogel designed for artificial cornea in a rabbit model. PEG/PAA hydrogel measuring 6 mm in diameter was implanted in the corneal stroma of twelve rabbits. Stromal flaps were created with a microkeratome. Randomly, six rabbits were assigned to bear the implant for 2 months, two rabbits for 6 months, two rabbits for 9 months, one rabbit for 12 months, and one rabbit for 16 months. Rabbits were evaluated monthly. After the assigned period, eyes were enucleated, and corneas were processed for histology and immunohistochemistry. There were clear corneas in three of six rabbits that had implantation of hydrogel for 2 months. In the six rabbits with implant for 6 months or longer, the corneas remained clear in four. There was a high rate of epithelial defect and corneal thinning in these six rabbits. One planned 9-month rabbit developed extrusion of implant at 4 months. The cornea remained clear in the 16-month rabbit but histology revealed epithelial in-growth. Intrastromal implantation of PEG/PAA resulted in a high rate of long-term complications. PMID:25778285

  8. Dually cross-linked single network poly(acrylic acid) hydrogels with superior mechanical properties and water absorbency.

    PubMed

    Zhong, Ming; Liu, Yi-Tao; Liu, Xiao-Ying; Shi, Fu-Kuan; Zhang, Li-Qin; Zhu, Mei-Fang; Xie, Xu-Ming

    2016-06-28

    Poly(acrylic acid) (PAA) hydrogels with superior mechanical properties, based on a single network structure with dual cross-linking, are prepared by one-pot free radical polymerization. The network structure of the PAA hydrogels is composed of dual cross-linking: a dynamic and reversible ionic cross-linking among the PAA chains enabled by Fe(3+) ions, and a sparse covalent cross-linking enabled by a covalent cross-linker (Bis). Under deformation, the covalently cross-linked PAA chains remain intact to maintain their original configuration, while the Fe(3+)-enabled ionic cross-linking among the PAA chains is broken to dissipate energy and then recombined. It is found that the mechanical properties of the PAA hydrogels are significantly influenced by the contents of covalent cross-linkers, Fe(3+) ions and water, which can be adjusted within a substantial range and thus broaden the applications of the hydrogels. Meanwhile, the PAA hydrogels have excellent recoverability based on the dynamic and reversible ionic cross-linking enabled by Fe(3+) ions. Moreover, the swelling capacity of the PAA hydrogels is as high as 1800 times in deionized water due to the synergistic effects of ionic and covalent cross-linkings. The combination of balanced mechanical properties, efficient recoverability, high swelling capacity and facile preparation provides a new method to obtain high-performance hydrogels. PMID:27230478

  9. Synthesis of silica coated zinc oxide–poly(ethylene-co-acrylic acid) matrix and its UV shielding evaluation

    SciTech Connect

    Ramasamy, Mohankandhasamy; Kim, Yu Jun; Gao, Haiyan; Yi, Dong Kee; An, Jeong Ho

    2014-03-01

    Graphical abstract: - Highlights: • Well layer thickness controlled silica shell was made on ZnO nanoparticles. • PEAA, an interfacial agent is used to make nanocomposite–polymer matrix by twin-screw extruder. • Si-ZnO/PEAA matrix is highly stable and UV protective as compared to ZnO/PEAA matrix. • Nanoparticle embedded polymer matrix is suggested to make UV shielding fabrics with Nylon4. - Abstract: Silica coated zinc oxide nanoparticles (Si-ZnO NPs) (7 nm thick) were synthesized successfully and melt blended with poly(ethylene-co-acrylic acid) (PEAA resin) to improving ultraviolet (UV) shielding of zinc oxide nanoparticles (ZnO NPs). The photostability of both the ZnO NPs and Si-ZnO NPs were analyzed by the difference in photoluminescence (PL) and by methylene blue (MB) degradation. Photo-degradation studies confirmed that Si-ZnO NPs are highly photostable compared to ZnO NPs. The melt blended matrices were characterized by field emission scanning electron microscopy interfaced with energy dispersive X-ray spectroscopy (FE-SEM-EDX). The UV shielding property was analyzed from the transmittance spectra of UV–visible (UV–vis) spectroscopy. The results confirmed fine dispersion of thick Si-ZnO NPs in the entire resin matrix. Moreover, the Si-ZnO/PEAA showed about 97% UV shielding properties than the ZnO/PEAA.

  10. Capture of Tumor Cells on Anti-EpCAM-Functionalized Poly(acrylic acid)-Coated Surfaces.

    PubMed

    Andree, Kiki C; Barradas, Ana M C; Nguyen, Ai T; Mentink, Anouk; Stojanovic, Ivan; Baggerman, Jacob; van Dalum, Joost; van Rijn, Cees J M; Terstappen, Leon W M M

    2016-06-15

    The presence of tumor cells in blood is predictive of short survival in several cancers and their isolation and characterization can guide toward the use of more effective treatments. These circulating tumor cells (CTC) are, however, extremely rare and require a technology that is sufficiently sensitive and specific to identify CTC against a background of billions of blood cells. Immuno-capture of cells expressing the epithelial cell adhesion molecule (EpCAM) are frequently used to enrich CTC from blood. The choice of bio conjugation strategy and antibody clone is crucial for adequate cell capture but is poorly understood. In this study, we determined the binding affinity constants and epitope binding of the EpCAM antibodies VU1D-9, HO-3, EpAb3-5, and MJ-37 by surface plasmon resonance imaging (SPRi). Glass surfaces were coated using a poly(acrylic acid) based coating and functionalized with anti-EpCAM antibodies. Binding of cells from the breast carcinoma cell line (SKBR-3) to the functionalized surfaces were compared. Although EpAb3-5 displayed the highest binding affinity HO-3 captured the highest amount of cells. Hence we report differences in the performance of the different antibodies and more importantly that the choice of antibody to capture CTC should be based on multiple assays. PMID:27187784

  11. Response of Swelling Behavior of Weak Branched Poly(ethylene imine)/Poly(acrylic acid) Polyelectrolyte Multilayers to Thermal Treatment.

    PubMed

    Gu, Yuanqing; Weinheimer, Emily K; Ji, Xiang; Wiener, Clinton G; Zacharia, Nicole S

    2016-06-21

    Weak polyelectrolyte multilayers (PEMs) prepared by the layer-by-layer technique have attracted a great deal of attention as smart responsive materials for biological and other applications in aqueous medium, but their dynamic behavior as a function of exposure to a wide temperature range is still not well understood. In this work, the thermally dependent swelling behavior of PEMs consisting of branched poly(ethylenimine) and poly(acrylic acid) is studied by temperature controlled in situ spectroscopic ellipsometry. Because of diffusion and interpenetration of polyelectrolytes during film deposition, the PEMs densify with increasing bilayer number, which further affects their water uptake behavior. Upon heating to temperatures below 60 °C, the worsened solvent quality of the PEM in water causes deswelling of the PEMs. However, once heated above this critical temperature, the hydrogen bonds within the PEMs are weakened, which allows for chain rearrangement within the film upon cooling, resulting in enhanced water uptake and increased film thickness. The current work provides fundamental insight into the unique dynamic behavior of weak polyelectrolyte multilayers in water at elevated temperatures. PMID:27232180

  12. Preparation and swelling behavior of a novel self-assembled β-cyclodextrin/acrylic acid/sodium alginate hydrogel.

    PubMed

    Huang, Zhanhua; Liu, Shouxin; Zhang, Bin; Wu, Qinglin

    2014-11-26

    A novel biodegradable β-cyclodextrin/acrylic acid/sodium alginate (CSA) hydrogel with a three-dimensional network structure was self-assembled by inverse suspension copolymerization. The CSA resin was pH sensitive and had good water absorption properties in pH 6-8 buffer solutions. At a β-CD:AA:SA mass ratio of 1:9:3 the CSA water absorbency was found to be 1403 g/g and the CSA hydrogel strength was 4.968 N. In 0.005-0.1 mol/L chloride salt and sulfate salt solutions the CSA water absorbencies increased as follows: NaCl>KCl>MgCl2>CaCl2>FeCl3, and Na2SO4>K2SO4>FeSO4>Al2(SO4)3, respectively. The release of water from the CSA hydrogel occurred slowly over 120 h. The biodegradation efficiency of the resin reached 85.3% for Lentinula edodes. The super water absorbency, good salt resistance and excellent water retention properties of CSA make it suitable for application as an agricultural water retention agent in saline soils. PMID:25256504

  13. Preparation of thermosensitive membranes by radiation grafting of acrylic acid/ N-isopropyl acrylamide binary mixture on PET fabric

    NASA Astrophysics Data System (ADS)

    Gupta, Bhuvanesh; Mishra, Swaiti; Saxena, Shalini

    2008-05-01

    Thermosensitive membranes were prepared by radiation-induced graft copolymerization of monomers on PET fabrics. A binary mixture of N-isopropyl acrylamide (NIPAAm) and acrylic acid (AA) was grafted on polyester fabric as a base material to introduce thermosensitive poly( N-isopropyl acrylamide) pendant chains having LCST slightly higher than 37 °C in the membrane. The influence of ferrous sulfate, radiation dose and monomer composition on the degree of grafting was studied. The structure of the grafted fabric was characterized by thermogravimetric analysis, differential scanning calorimetry and scanning electron microscopy. The thermosensitive nature of the fabric was monitored by swelling at different temperatures. The graft copolymerization of AA with NIPAAm enhanced the LCST of the resultant membrane to ˜37 °C. The moisture vapor transmission rate (MVTR) and air permeability of the fabric decreased slightly, may be due to the slight blocking of the fabric pores. The immobilization of tetracycline hydrochloride as the model drug and its release characteristics at different temperatures were monitored.

  14. Hysteretic memory in pH-response of water contact angle on poly(acrylic acid) brushes.

    PubMed

    Yadav, Vivek; Harkin, Adrienne V; Robertson, Megan L; Conrad, Jacinta C

    2016-04-13

    We investigated the pH-dependent response of flat polyacid brushes of varying length and dispersity in the extended brush regime. Our model system consisted of poly(acrylic acid) brushes, which change from hydrophobic and neutral at low pH to hydrophilic and negatively charged at high pH, synthesized on silicon substrates using a grafting-from approach at constant grafting density. We observed three trends in the pH-response: first, the dry brush thickness increased as the pH was increased for brushes above a critical length, and this effect was magnified as the dispersity increased; second, the water contact angle measured at low pH was larger for brushes of greater dispersity; and third, brushes of sufficient dispersity exhibited hysteretic memory behavior in the pH-dependence of the contact angle, in which the contact angle upon increasing and decreasing pH differed. As a consequence, the pKa of the brushes measured upon increasing pH was consistently higher than that measured upon decreasing pH. The observed pH response is consistent with proposed changes in the conformation and charge distribution of the polyelectrolyte brushes that depend on the direction of pH change and the dispersity of the brushes. PMID:26979270

  15. Starch-g-Poly-(N, N-dimethyl acrylamide-co-acrylic acid): an efficient Cr (VI) ion binder.

    PubMed

    Kolya, Haradhan; Roy, Anirban; Tripathy, Tridib

    2015-01-01

    Synthesis of Starch-g-(Poly N, N-dimethylacrylamide-co-acrylic acid) was carried out by solution polymerization technique using potassium perdisulfate (K(2)S(2)O(8)) as the initiator. The graft copolymer was characterized by measuring molecular weight, using size exclusion chromatography (SEC), FTIR spectroscopy and X-ray diffraction (XRD) studies. The synthetic graft copolymer was used for removal of hexavalent chromium ion [Cr (VI)] from its aqueous solution. Various operating variables affecting the metal sorption such as, the amount of adsorbent, solution pH, contact time, temperature and the Cr (VI) solution concentration were extensively investigated. FTIR and UV-VIS spectroscopy, cyclic voltammetry (CV) were employed to study the metal complexation. The adsorption data could be well described by the pseudo-second-order and Langmuir isotherm model which indicate a chemisorption process. Calculation of the various thermodynamic parameters for the adsorption was also done. The negative value of free energy change (ΔG°) indicates the spontaneous nature of the adsorption. PMID:25224290

  16. Enhancing antibiofouling performance of Polysulfone (PSf) membrane by photo-grafting of capsaicin derivative and acrylic acid

    NASA Astrophysics Data System (ADS)

    Wang, Jian; Sun, Haijing; Gao, Xueli; Gao, Congjie

    2014-10-01

    Biofouling is a critical issue in membrane water and wastewater treatment. Herein, antibiofouling PSf membrane was prepared by UV-assisted graft polymerization of acrylic acid (AA) and a capsaicin derivative, N-(5-methyl-3-tert-butyl-2-hydroxy benzyl) acrylamide (MBHBA), on PSf membrane. AA and MBHBA were used as hydrophilic monomer and antibacterial monomer separately. The membranes were characterized by FTIR-ATR, contact angle, SEM, AFM, cross-flow filtration unit, antifouling and antibacterial measurements. Verification of MBHBA and AA that photo-chemically grafted onto the PSf membrane surface is confirmed by carbonyl stretching vibration at ∼1655 cm-1 and ∼1730 cm-1, separately. The increasing AA concentration accelerates the graft-polymerization of MBHBA and resulted in a more hydrophilic surface. Consequently, antifouling property of the membranes was improved on a large level. The flux recovery rate can achieve 100% during the cyclic test, which may be attributed to the more hydrophilic and smooth surface, as well as the decreased membrane pore size. Most importantly, the presence of AA in graft co-polymer does not affect the antibacterial activity of MBHBA. That may be induced by the increasing chain length and flexibility of the grafted polymer chains.

  17. Highly hydrophilic ultra-high molecular weight polyethylene powder and film prepared by radiation grafting of acrylic acid

    NASA Astrophysics Data System (ADS)

    Wang, Honglong.; Xu, Lu.; Li, Rong.; Pang, Lijuan.; Hu, Jiangtao.; Wang, Mouhua.; Wu, Guozhong.

    2016-09-01

    The surface properties of ultra-high molecular weight polyethylene (UHMWPE) are very important for its use in engineering or composites. In this work, hydrophilic UHMWPE powder and film were prepared by γ-ray pre-irradiation grafting of acrylic acid (AA) and further neutralization with sodium hydroxide solution. Variations in the chemical structure, grafting yield and hydrophilicity were investigated and compared. FT-IR and XPS analysis results showed that AA was successfully grafted onto UHMWPE powder and film; the powder was more suitable for the grafting reaction in 1 wt% AA solution than the film. Given a dose of 300 kGy, the grafting yield of AA was ∼5.7% for the powder but ∼0.8% for the film under identical conditions. Radiation grafting of a small amount of AA significantly improved the hydrophilicity of UHMWPE. The water contact angle of the UHMWPE-g-PAA powder with a grafting yield of AA at ∼5.7% decreased from 110.2° to 68.2°. Moreover, the grafting powder (UHMWPE-g-PAA) exhibited good dispersion ability in water.

  18. Synthesis of bioadhesive poly(acrylic acid) nano- and microparticles using an inverse emulsion polymerization method for the entrapment of hydrophilic drug candidates.

    PubMed

    Kriwet, B; Walter, E; Kissel, T

    1998-12-01

    Bioadhesive latices of water-swollen poly(acrylic acid) nano-and microparticles were synthesized using an inverse (W/O) emulsion polymerization method. They are stabilized by a co-emulsifier system consisting of SpanTM 80 and TweenTM 80 dispersed in aliphatic hydrocarbons. The initial polymerization medium contains emulsion droplets and inverse micelles which solubilize a part of the monomer solution. The polymerization is initiated by free radicals, and particle dispersions with a narrow size distribution are obtained. The particle size is dependent on the type of radical initiator used. With water-soluble initiators, for example ammonium persulfate, microparticles were obtained in the size range of 1 to 10 micrometer indicating that these microparticles originate from the emulsion droplets since the droplet sizes of the W/O emulsion show similar distribution. When lipophilic radical initiators, such as azobis-isobutyronitrile, are used, almost exclusively nanoparticles are generated with diameters in the range of 80 to 150 nm, due to the limited solubility of oligomeric poly(acrylic acid) chains in the lipophilic continuous phase. These poly(acrylic acid) micro- and nanoparticles yielded excellent bioadhesive properties in an in-vitro assay and may, therefore, be suitable for the encapsulation of peptides and other hydrophilic drugs. PMID:9801438

  19. Methyl acrylate

    Integrated Risk Information System (IRIS)

    Methyl acrylate ; CASRN 96 - 33 - 3 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  20. Poly(acrylic acid)-block-poly(vinyl alcohol) anchored maghemite nanoparticles designed for multi-stimuli triggered drug release

    NASA Astrophysics Data System (ADS)

    Liu, Ji; Detrembleur, Christophe; Debuigne, Antoine; de Pauw-Gillet, Marie-Claire; Mornet, Stéphane; Vander Elst, Luce; Laurent, Sophie; Labrugère, Christine; Duguet, Etienne; Jérôme, Christine

    2013-11-01

    Original core/corona nanoparticles composed of a maghemite core and a stimuli-responsive polymer coating made of poly(acrylic acid)-block-poly(vinyl alcohol) macromolecules were fabricated for drug delivery system (DDS) application. This kind of DDS aims to combine the advantage of stimuli-responsive polymer coating, in order to regulate the drug release behaviours under different conditions and furthermore, improve the biocompatibility and in vivo circulation half-time of the maghemite nanoparticles. Drug loading capacity was evaluated with methylene blue (MB), a cationic model drug. The triggered release of MB was studied under various stimuli such as pH, ionic strength and temperature. Local heating generated under alternating magnetic field (AMF) application was studied, and remotely AMF-triggered release was also confirmed, while a mild heating-up of the release medium was observed. Furthermore, their potential application as magnetic resonance imaging (MRI) contrast agents was explored via relaxivity measurements and acquisition of T2-weighted images. Preliminary studies on the cytotoxicity against mouse fibroblast-like L929 cell line and also their cellular uptake within human melanoma MEL-5 cell line were carried out. In conclusion, this kind of stimuli-responsive nanoparticles appears to be promising carriers for delivering drugs to some tumour sites or into cellular compartments with an acidic environment.Original core/corona nanoparticles composed of a maghemite core and a stimuli-responsive polymer coating made of poly(acrylic acid)-block-poly(vinyl alcohol) macromolecules were fabricated for drug delivery system (DDS) application. This kind of DDS aims to combine the advantage of stimuli-responsive polymer coating, in order to regulate the drug release behaviours under different conditions and furthermore, improve the biocompatibility and in vivo circulation half-time of the maghemite nanoparticles. Drug loading capacity was evaluated with methylene

  1. Energy performance evaluation of AAC

    NASA Astrophysics Data System (ADS)

    Aybek, Hulya

    was accomplished by using conducting several simulation models to determine the relative energy efficiency of wood-framed, metal-framed, and Aerated Autoclaved Concrete (AAC) wall structures for both commercial and residential buildings.

  2. A method for preparing sodium acrylate-d3, a useful and stable precursor for deuterated acrylic monomers

    SciTech Connect

    Yang, Jun; Hong, Kunlun; Bonnesen, Peter V

    2011-01-01

    A convenient and economical method for converting propiolic acid to sodium acrylate-d3 is described. Successive D/H exchange of the alkyne proton of sodium propiolate (prepared from propiolic acid) using D2O affords sodium propiolate-d having up to 99 atom% D. Sodium propiolate-d can be partially reduced to sodium acrylate-d3 with 90% conversion and 89% yield, using D2 and the Lindlar catalyst with control of reaction parameters to maximize conversion while minimizing over reduction.

  3. Self-assembled poly(ethylene glycol)-co-acrylic acid microgels to inhibit bacterial colonization of synthetic surfaces.

    PubMed

    Wang, Qichen; Uzunoglu, Emel; Wu, Yong; Libera, Matthew

    2012-05-01

    We explored the use of self-assembled microgels to inhibit the bacterial colonization of synthetic surfaces both by modulating surface cell adhesiveness at length scales comparable to bacterial dimensions (∼1 μm) and by locally storing/releasing an antimicrobial. Poly(ethylene glycol) [PEG] and poly(ethylene glycol)-co-acrylic acid [PEG-AA] microgels were synthesized by suspension photopolymerization. Consistent with macroscopic gels, a pH dependence of both zeta potential and hydrodynamic diameter was observed in AA-containing microgels but not in pure PEG microgels. The microgels were electrostatically deposited onto poly(l-lysine) (PLL) primed silicon to form submonolayer surface coatings. The microgel surface density could be controlled via the deposition time and the microgel concentration in the parent suspension. In addition to their intrinsic antifouling properties, after deposition, the microgels could be loaded with a cationic antimicrobial peptide (L5) because of favorable electrostatic interactions. Loading was significantly higher in PEG-AA microgels than in pure PEG microgels. The modification of PLL-primed Si by unloaded PEG-AA microgels reduced the short-term (6 h) S. epidermidis surface colonization by a factor of 2, and the degree of inhibition increased when the average spacing between microgels was reduced. Postdeposition L5 peptide loading into microgels further reduced bacterial colonization to the extent that, after 10 h of S. epidermidis culture in tryptic soy broth, the colonization of L5-loaded PEG-AA microgel-modified Si was comparable to the very small level of colonization observed on macroscopic PEG gel controls. The fact that these microgels can be deposited by a nonline-of-sight self-assembly process and hinder bacterial colonization opens the possibility of modifying the surfaces of topographically complex biomedical devices and reduces the rate of biomaterial-associated infection. PMID:22519439

  4. Nanoclays reinforced glass ionomer cements: dispersion and interaction of polymer grade (PG) montmorillonite with poly(acrylic acid).

    PubMed

    Fareed, Muhammad A; Stamboulis, Artemis

    2014-01-01

    Montmorillonite nanoclays (PGV and PGN) were dispersed in poly(acrylic acid) (PAA) for utilization as reinforcing filler in glass ionomer cements (GICs). Chemical and physical interaction of PAA and nanoclay (PGV and PGN) was studied. PAA–PGV and PAA–PGN solutions were prepared in different weight percent loadings of PGV and PGN nanoclay (0.5-8.0 wt%) via exfoliation-adsorption method. Characterization was carried out by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and fourier transform infrared (FTIR) spectroscopy. XRD results of PAA–PGN demonstrated that the interlayer space expanded from 12.83 to 16.03 Å indicating intercalation whereas the absence of the peak at d(001) in PAA–PGV indicated exfoliation. XPS scans of PGV and PGN nanoclays depicted the main peak of O 1s photoelectron due to Si–O–M (M = Mg, Al, Fe) whereas, Si–O–Al linkages were identified by Si 2p or Si 2s and Al 2p or Al 2s peaks. The disappearance of the Na peak confirmed that PAA molecules exchanged sodium ions present on surface of silicate layers and significantly reduced the electrostatic van-der-Waals forces between silicate plates resulting in intercalation or exfoliation. FTIR spectra of PAA–nanoclay suspensions demonstrated the presence of a new peak at 1,019 cm(-1) associated with Si–O– stretching vibrations which increased with increasing nanoclays concentration. Information concerning the dispersion of nanoclay in PAA aqueous solutions, chemical reaction and increase interlayer space in montmorillonite nanoclay is particularly useful regarding dispersion and reinforcement of nanoclay in PAA. PMID:24077996

  5. The Chemical and Physical Properties of Poly(ε-caprolactone) Scaffolds Functionalised with Poly(vinyl phosphonic acid-co-acrylic acid).

    PubMed

    Bassi, A K; Gough, J E; Zakikhani, M; Downes, S

    2011-01-01

    There is a clinical need for a synthetic alternative to bone graft substitute (BGS) derived from demineralised bone matrix. We report the electrospinning of Poly(ε-caprolactone) (PCL) to form a 3-dimensional scaffold for use as a synthetic BGS. Additionally, we have used Poly(vinyl phosphonic acid-co-acrylic acid) (PVPA) to improve bone formation. Fibres were formed using a 10% w/v PCL/acetone solution. Infrared spectroscopy confirmed that the electrospinning process had no effect on the functional groups present in the resulting structure. The electrospun scaffolds were coated with PVPA (PCL/PVPA), and characterised. The stability of the PVPA coating after immersion in culture medium was assessed over 21 days. There was rapid release of the coating until day 2, after which the coating became stable. The wettability of the PCL scaffolds improved significantly, from 123.3 ± 10.8° to 43.3 ± 1.2° after functionalisation with PVPA. The compressive strength of the PCL/PVPA scaffolds (72 MPa) was significantly higher to that of the PCL scaffold (14 MPa), and an intermediate between trabecular and cortical bone (7 MPa and 170 MPa, resp.). The study has demonstrated that the PCL/PVPA scaffold has the desired chemical and biomechanical characteristics required for a material designed to be used as a BGS. PMID:22073379

  6. The Chemical and Physical Properties of Poly(ε-caprolactone) Scaffolds Functionalised with Poly(vinyl phosphonic acid-co-acrylic acid)

    PubMed Central

    Bassi, A. K.; Gough, J. E.; Zakikhani, M.; Downes, S.

    2011-01-01

    There is a clinical need for a synthetic alternative to bone graft substitute (BGS) derived from demineralised bone matrix. We report the electrospinning of Poly(ε-caprolactone) (PCL) to form a 3-dimensional scaffold for use as a synthetic BGS. Additionally, we have used Poly(vinyl phosphonic acid-co-acrylic acid) (PVPA) to improve bone formation. Fibres were formed using a 10% w/v PCL/acetone solution. Infrared spectroscopy confirmed that the electrospinning process had no effect on the functional groups present in the resulting structure. The electrospun scaffolds were coated with PVPA (PCL/PVPA), and characterised. The stability of the PVPA coating after immersion in culture medium was assessed over 21 days. There was rapid release of the coating until day 2, after which the coating became stable. The wettability of the PCL scaffolds improved significantly, from 123.3 ± 10.8° to 43.3 ± 1.2° after functionalisation with PVPA. The compressive strength of the PCL/PVPA scaffolds (72 MPa) was significantly higher to that of the PCL scaffold (14 MPa), and an intermediate between trabecular and cortical bone (7 MPa and 170 MPa, resp.). The study has demonstrated that the PCL/PVPA scaffold has the desired chemical and biomechanical characteristics required for a material designed to be used as a BGS. PMID:22073379

  7. Molecular Dynamics Simulations of Adsorption of Poly(acrylic acid) and Poly(methacrylic acid) on Dodecyltrimethylammonium Chloride Micelle in Water: Effect of Charge Density.

    PubMed

    Sulatha, Muralidharan S; Natarajan, Upendra

    2015-09-24

    We have investigated the interaction of dodecyltrimethylammonium chloride (DoTA) micelle with weak polyelectrolytes, poly(acrylic acid) and poly(methacrylic acid). Anionic as well as un-ionized forms of the polyelectrolytes were studied. Polyelectrolyte-surfactant complexes were formed within 5-11 ns of the simulation time and were found to be stable. Association is driven purely by electrostatic interactions for anionic chains whereas dispersion interactions also play a dominant role in the case of un-ionized chains. Surfactant headgroup nitrogen atoms are in close contact with the carboxylic oxygens of the polyelectrolyte chain at a distance of 0.35 nm. In the complexes, the polyelectrolyte chains are adsorbed on to the hydrophilic micellar surface and do not penetrate into the hydrophobic core of the micelle. Polyacrylate chain shows higher affinity for complex formation with DoTA as compared to polymethacrylate chain. Anionic polyelectrolyte chains show higher interaction strength as compared to corresponding un-ionized chains. Anionic chains act as polymeric counterion in the complexes, resulting in the displacement of counterions (Na(+) and Cl(-)) into the bulk solution. Anionic chains show distinct shrinkage upon adsorption onto the micelle. Detailed information about the microscopic structure and binding characteristics of these complexes is in agreement with available experimental literature. PMID:26355463

  8. Nacre-inspired integrated strong and tough reduced graphene oxide-poly(acrylic acid) nanocomposites.

    PubMed

    Wan, Sijie; Hu, Han; Peng, Jingsong; Li, Yuchen; Fan, Yuzun; Jiang, Lei; Cheng, Qunfeng

    2016-03-01

    Inspired by the relationship between interface interactions and the high performance mechanical properties of nacre, a strong and tough nacre-inspired nanocomposite was demonstrated based on graphene oxide (GO) and polyacrylic acid (PAA) prepared via a vacuum-assisted filtration self-assembly process. The abundant hydrogen bonding between GO and PAA results in both high strength and toughness of the bioinspired nanocomposites, which are 2 and 3.3 times higher than that of pure reduced GO film, respectively. In addition, the effect of environmental relative humidity on the mechanical properties of bioinspired nanocomposites is also investigated, and is consistent with previous theoretical predictions. Moreover, this nacre-inspired nanocomposite also displays high electrical conductivity of 108.9 S cm(-1). These excellent physical properties allow this type of nacre-inspired nanocomposite to be used in many applications, such as flexible electrodes, aerospace applications, and artificial muscles etc. This nacre-inspired strategy also opens an avenue for constructing integrated high performance graphene-based nanocomposites in the near future. PMID:26895081

  9. Preparation of Poly Acrylic Acid-Poly Acrylamide Composite Nanogels by Radiation Technique

    PubMed Central

    Ghorbaniazar, Parisa; Sepehrianazar, Amir; Eskandani, Morteza; Nabi-Meibodi, Mohsen; Kouhsoltani, Maryam; Hamishehkar, Hamed

    2015-01-01

    Purpose: Nanogel, a nanoparticle prepared from a cross-linked hydrophilic polymer network, has many biomedical applications. A radiation technique has recently been introduced as one of the appropriate methods for the preparation of polymeric nanogels due to its additive-free initiation and easy control procedure. Methods: We have investigated the formation of nano-sized polymeric gels, based on the radiation-induced inter- and intra-molecular cross-linking of the inter-polymer complex (IPC) of polyacrylamide (PAAm) and polyacrylic acide (PAAc). Results: The results indicated that the prepared polymeric complex composed of PAAm and PAAc was converted into nanogel by irradiation under different doses (1, 3, 5 and 7 kGy). This was due to inter- and intra-molecular cross-linking at the range of 446-930 nm as characterized by the photon correlation spectroscopy method. Increasing the irradiation dose reduced the size of nanoparticles to 3 kGy; however, the higher doses increased the size and size distribution. Scanning electron microscopy images indicated the nanogel formation in the reported size by particle size and showed the microcapsule structure of the prepared nanogels. Biocompatibility of nanogels were assessed and proved by MTT assay. Conclusion: It was concluded that low dose irradiation can be successfully applied for nanometre-ranged hydrogel. PMID:26236667

  10. Self-healing multilayer polyelectrolyte composite film with chitosan and poly(acrylic acid).

    PubMed

    Zhu, Yanxi; Xuan, Hongyun; Ren, Jiaoyu; Ge, Liqin

    2015-11-21

    If self-healing materials can be prepared via simple technology and methods using nontoxic materials, this would be a great step forward in the creation of environmentally friendly self-healing materials. In this paper, the specific structural parameters of the various hydrogen bonds between chitosan (CS) and polyacrylic acid (PAA) were calculated. Then, multilayer polyelectrolyte films were fabricated with CS and PAA based on layer-by-layer (LbL) self-assembly technology at different pH values. The possible influence of pH on the (CS/PAA) × 30 multilayer polyelectrolyte film was investigated. The results show that the interactions between CS and PAA, swelling capacity, microstructure, wettability, and self-healing ability are all governed by the pH of the CS solution. When the pH value of the CS solution is 3.0, the prepared multilayer polyelectrolyte film (CS3.0/PAA2.8) × 30 has fine-tuned interactions, a network-like structure, good swelling ability, good hydrophilicity, and excellent self-healing ability. This promises to greatly widen the future applications of environmentally friendly materials and bio-materials. PMID:26364567

  11. Nacre-inspired integrated strong and tough reduced graphene oxide-poly(acrylic acid) nanocomposites

    NASA Astrophysics Data System (ADS)

    Wan, Sijie; Hu, Han; Peng, Jingsong; Li, Yuchen; Fan, Yuzun; Jiang, Lei; Cheng, Qunfeng

    2016-03-01

    Inspired by the relationship between interface interactions and the high performance mechanical properties of nacre, a strong and tough nacre-inspired nanocomposite was demonstrated based on graphene oxide (GO) and polyacrylic acid (PAA) prepared via a vacuum-assisted filtration self-assembly process. The abundant hydrogen bonding between GO and PAA results in both high strength and toughness of the bioinspired nanocomposites, which are 2 and 3.3 times higher than that of pure reduced GO film, respectively. In addition, the effect of environmental relative humidity on the mechanical properties of bioinspired nanocomposites is also investigated, and is consistent with previous theoretical predictions. Moreover, this nacre-inspired nanocomposite also displays high electrical conductivity of 108.9 S cm-1. These excellent physical properties allow this type of nacre-inspired nanocomposite to be used in many applications, such as flexible electrodes, aerospace applications, and artificial muscles etc. This nacre-inspired strategy also opens an avenue for constructing integrated high performance graphene-based nanocomposites in the near future.

  12. Extending framework based on the linear coordination polymers: Alternative chains containing lanthanum ion and acrylic acid ligand

    SciTech Connect

    Li Hui . E-mail: lihui@bit.edu.cn; Guo Ming; Tian Hong; He Feiyue; Lee, G.-H.; Peng, S.-M.

    2006-11-15

    One-dimensional alternative chains of two lanthanum complexes: [La(L{sup 1}){sub 3}(CH{sub 3}OH)(H{sub 2}O){sub 2}].5H{sub 2}O (L{sup 1}=anion of {alpha}-cyano-4-hydroxycinnamic acid ) 1 and [La(L{sup 2}){sub 3}(H{sub 2}O){sub 2}].3H{sub 2}O (L{sup 2}=anion of trans-3-(4-methyl-benzoyl)-acrylic acid) 2 were synthesized and structurally characterized by single-crystal X-ray diffraction, element analysis, IR and thermogravimetric analysis. The crystal structure data are as follows for 1: C{sub 31}H{sub 36}LaN{sub 3}O{sub 17}, triclinic, P-1, a=9.8279(4)A, b=11.8278(5)A, c=17.8730(7)A, {alpha}=72.7960(10){sup o}, {beta}=83.3820(10){sup o}, {gamma}=67.1650(10)-bar , Z=2, R{sub 1}=0.0377, wR{sub 2}=0.0746; for 2: C{sub 33}H{sub 37}LaO{sub 14}, triclinic, P-1, a=8.7174(5)A, b=9.9377(5)A, c=21.153(2)A, {alpha}=81.145(2){sup o}, {beta}=87.591(2){sup o}, {gamma}=67.345(5){sup o}, Z=2, R{sub 1}=0.0869, wR{sub 2}=0.220. 1 is a rare example of the alternative chain constructed by syn-syn and anti-syn coordination mode of carboxylato ligand arranged along the chain alternatively. La(III) ions in 2 are linked by two {eta}{sup 3}-O bridges and four bridges (two {eta}{sup 2}-O and two {eta}{sup 3}-O) alternatively. Both of the linear coordination polymers grow into two- and three-dimensional networks by packing through extending hydrogen-bond network directed by ligands.

  13. Superabsorbent hydrogels via graft polymerization of acrylic acid from chitosan-cellulose hybrid and their potential in controlled release of soil nutrients.

    PubMed

    Essawy, Hisham A; Ghazy, Mohamed B M; El-Hai, Farag Abd; Mohamed, Magdy F

    2016-08-01

    Superabsorbent polymers fabricated via grafting polymerization of acrylic acid from chitosan (CTS) yields materials that suffer from poor mechanical strength. Hybridization of chitosan with cellulose (Cell) via chemical bonding using thiourea formaldehyde resin increases the flexibility of the produced hybrid (CTS/Cell). The hybridization process and post graft polymerization of acrylic acid was followed using Fourier transform infrared (FTIR). Also, the obtained structures were homogeneous and exhibited uniform surface as could be shown from imaging with scanning electron microscopy (SEM). Thus, the polymers derived from the grafting of polyacrylic acid from (CTS/Cell) gave rise to much more mechanically robust structures ((CTS/Cell)-g-PAA) that bear wide range of pH response due to presence of chitosan and polyacrylic acid in one homogeneous entity. Additionally, the obtained structures possessed greater water absorbency 390, 39.5g/g in distilled water and saline (0.9wt.% NaCl solution), respectively, and enhanced retention potential even at elevated temperatures as revealed by thermogravimetric analysis (TGA). This could be explained by the high grafting efficiency (GE%), 86.4%, and grafting yield (GY%), 750%. The new superabsorbent polymers proved to be very efficient devices for controlled release of fertilizers into the soil which expands their use in agriculture and horticultural applications. PMID:27126169

  14. Biointegration of corneal macroporous membranes based on poly(ethyl acrylate) copolymers in an experimental animal model.

    PubMed

    Alió del Barrio, Jorge L; Chiesa, Massimo; Gallego Ferrer, Gloria; Garagorri, Nerea; Briz, Nerea; Fernandez-Delgado, Jorge; Sancho-Tello Valls, Maria; Botella, Carmen Carda; García-Tuñón, Ignacio; Bataille, Laurent; Rodriguez, Alejandra; Arnalich-Montiel, Francisco; Gómez Ribelles, Jose L; Antolinos-Turpín, Carmen M; Gómez-Tejedor, Jose A; Alió, Jorge L; De Miguel, Maria P

    2015-03-01

    Currently available keratoprosthesis models (nonbiological corneal substitutes) have a less than 75% graft survival rate at 2 years. We aimed at developing a model for keratoprosthesis based on the use of poly(ethyl acrylate) (PEA)-based copolymers, extracellular matrix-protein coating and colonization with adipose-derived mesenchymal stem cells. Human adipose tissue derived mesenchymal stem cells (h-ADASC) colonization efficiency of seven PEA-based copolymers in combination with four extracellular matrix coatings were evaluated in vitro. Then, macroporous membranes composed of the optimal PEA subtypes and coating proteins were implanted inside rabbit cornea. After a 3-month follow-up, the animals were euthanized, and the clinical and histological biointegration of the implanted material were assessed. h-ADASC adhered and survived when cultured in all PEA-based macroporous membranes. The addition of high hydrophilicity to PEA membranes decreased h-ADASC colonization in vitro. PEA-based copolymer containing 10% hydroxyethyl acrylate (PEA-HEA10) or 10% acrylic acid (PEA-AAc10) monomeric units showed the best cellular colonization rates. Collagen plus keratan sulfate-coated polymers demonstrated enhanced cellular colonization respect to fibronectin, collagen, or uncoated PEAs. In vivo implantation of membranes resulted in an extrusion rate of 72% for PEA, 50% for PEA-AAc10, but remarkably of 0% for PEA-HEA10. h-ADASC survival was demonstrated in all the membranes after 3 months follow-up. A slight reduction in the extrusion rate of h-ADASC colonized materials was observed. No significant differences between the groups with and without h-ADASC were detected respect to transparency or neovascularization. We propose PEA with low hydroxylation as a scaffold for the anchoring ring of future keratoprosthesis. PMID:24910285

  15. Folic acid conjugated cross-linked acrylic polymer (FA-CLAP) hydrogel for site specific delivery of hydrophobic drugs to cancer cells

    PubMed Central

    2014-01-01

    Background The hydrogel based system is found to be rarely reported for the delivery of hydrophobic drug due to the incompatibility of hydrophilicity of the polymer network and the hydrophobicity of drug. This problem can be solved by preparing semi-interpenetrating network of cross-linked polymer for tuning the hydrophilicity so as to entrap the hydrophobic drugs. The current study is to develop a folic acid conjugated cross-linked pH sensitive, biocompatible polymeric hydrogel to achieve a site specific drug delivery. For that, we have synthesized a folic acid conjugated PEG cross-linked acrylic polymer (FA-CLAP) hydrogel and investigated its loading and release of curcumin. The formed polymer hydrogel was then conjugated with folic acid for the site specific delivery of curcumin to cancer cells and then further characterized and conducted the cell uptake and cytotoxicity studies on human cervical cancer cell lines (HeLa). Results In this study, we synthesized folic acid conjugated cross-linked acrylic hydrogel for the delivery of hydrophobic drugs to the cancer site. Poly (ethyleneglycol) (PEG) diacrylate cross-linked acrylic polymer (PAA) was prepared via inverse emulsion polymerization technique and later conjugated it with folic acid (FA-CLAP). Hydrophobic drug curcumin is entrapped into it and investigated the entrapment efficiency. Characterization of synthesized hydogel was done by using Fourier Transform-Infrared spectroscopy (FT-IR), Transmission Electron Microscopy (TEM), Differential Scanning Calorimetry (DSC). Polymerization and folate conjugation was confirmed by FT-IR spectroscopy. The release kinetics of drug from the entrapped form was studied which showed initial burst release followed by sustained release due to swelling and increased cross-linking. In vitro cytotoxicity and cell uptake studies were conducted in human cervical cancer (HeLa) cell lines. Conclusions Results showed that curcumin entrapped folate conjugated cross-linked acrylic

  16. TiO2 supported over porous silica photocatalysts for pesticide degradation using solar light: Part 2. Silica prepared using acrylic acid emulsion.

    PubMed

    Sharma, Mangalampalli V Phanikrishna; Kumari, Valluri Durga; Subrahmanyam, Machiraju

    2010-03-15

    An acrylic acid emulsion mixture is used for synthesis of novel porous silica (E-Si) material. The photocatalytic activity of TiO2 under solar light irradiation for isoproturon (herbicide) degradation is drastically increased when dispersed over E-Si support using solid state dispersion (SSD) technique. The composite material is characterized by XRD, nitrogen adsorption-desorption isotherms, UV-vis DRS, SEM and TEM measurements. The photocatalytic activities of the composite catalysts are evaluated for different parameters. The 5 wt% TiO2/E-Si is found to be highly active for isoproturon degradation. PMID:19962829

  17. Directed self-assembly of poly(styrene)-block-poly(acrylic acid) copolymers for sub-20nm pitch patterning

    NASA Astrophysics Data System (ADS)

    Cheng, Jing; Lawson, Richard A.; Yeh, Wei-Ming; Jarnagin, Nathan D.; Peters, Andrew; Tolbert, Laren M.; Henderson, Clifford L.

    2012-03-01

    Directed self-assembly (DSA) of block copolymers is a promising technology for extending the patterning capability of current lithographic exposure tools. For example, production of sub-40 nm pitch features using 193nm exposure technologies is conceivably possible using DSA methods without relying on time consuming, challenging, and expensive multiple patterning schemes. Significant recent work has focused on demonstration of the ability to produce large areas of regular grating structures with low numbers of defects using self-assembly of poly(styrene)-b-poly(methyl methacrylate) copolymers (PS-b-PMMA). While these recent results are promising and have shown the ability to print pitches approaching 20 nm using DSA, the ability to advance to even smaller pitches will be dependent upon the ability to develop new block copolymers with higher χ values and the associated alignment and block removal processes required to achieve successful DSA with these new materials. This paper reports on work focused on identifying higher χ block copolymers and their associated DSA processes for sub-20 nm pitch patterning. In this work, DSA using polystyrene-b-polyacid materials has been explored. Specifically, it is shown that poly(styrene)-b-poly(acrylic acid) copolymers (PS-b-PAA) is one promising material for achieving substantially smaller pitch patterns than those possible with PS-b-PMMA while still utilizing simple hydrocarbon polymers. In fact, it is anticipated that much of the learning that has been done with the PS-b-PMMA system, such as development of highly selective plasma etch block removal procedures, can be directly leveraged or transferred to the PS-b-PAA system. Acetone vapor annealing of PS-b-PAA (Mw=16,000 g/mol with 50:50 mole ratio of PS:PAA) and its self-assembly into a lamellar morphology is demonstrated to generate a pattern pitch size (L0) of 21 nm. The χ value for PS-b-PAA was estimated from fingerprint pattern pitch data to be approximately 0.18 which

  18. Curcumin delivery from poly(acrylic acid-co-methyl methacrylate) hollow microparticles prevents dopamine-induced toxicity in rat brain synaptosomes.

    PubMed

    Yoncheva, Krassimira; Kondeva-Burdina, Magdalena; Tzankova, Virginia; Petrov, Petar; Laouani, Mohamed; Halacheva, Silvia S

    2015-01-01

    The potential of poly(methyl methacrylate-co-acrylic acid) (PMMA-AA) copolymers to form hollow particles and their further formulation as curcumin delivery system have been explored. The particles were functionalized by crosslinking the acrylic acid groups via bis-amide formation with either cystamine (CYS) or 3,3'-dithiodipropionic acid dihydrazide (DTP) which simultaneously incorporated reversibility due to the presence of disulfide bonds within the crosslinker. Optical micrographs showed the formation of spherical hollow microparticles with a size ranging from 1 to 7 μm. Curcumin was loaded by incubation of its ethanol solution with aqueous dispersions of the cross-linked particles and subsequent evaporation of the ethanol. Higher loading was observed in the microparticles with higher content of hydrophobic PMMA units indicating its influence upon the loading of hydrophobic molecules such as curcumin. The in vitro release studies in a phosphate buffer showed no initial burst effect and sustained release of curcumin that correlated with the swelling of the particles under these conditions. The capacity of encapsulated and free curcumin to protect rat brain synaptosomes against dopamine-induced neurotoxicity was examined. The encapsulated curcumin showed greater protective effects in rat brain synaptosomes as measured by synaptosomal viability and increased intracellular levels of glutathione. PMID:25839414

  19. Synthesis of comb type and semi-interpenetrating networks of acryloyl- L-proline methyl ester and poly (acrylic acid) for Cu (II) immobilization

    NASA Astrophysics Data System (ADS)

    González, Giovanni; Burillo, Guillermina

    2010-08-01

    Graft copolymer hydrogels and semi-interpenetrating networks (s-IPN) of acryloyl- L-proline methyl ester (A-ProOMe) and poly (acrylic acid) (PAAc) were synthesized in methanol solutions, by ionizing radiation (γ rays from a Co 60 source at room temperature). These systems are thermo and pH-sensitive and the pH sensitivity increases from acidic to basic solutions. The Lower Critical Solution Temperature (LCST), due to presence of poly (acryloyl- L-proline methyl ester) (PA-ProOMe) has been found between 18 and 20 °C and an unexpected Upper Critical Solution Temperature (UCST) due to poly acrylic acid (PAAc) has been found between 21 and 22 °C. Preliminary studies on the immobilization of Cu 2+ for both hydrogels were done at several pH values at room temperature. Other techniques employed to characterize the comb type hydrogels and sIPN included scanning electronic microscopy (SEM) and infrared (FTIR-ATR).

  20. Plasma copolymer surfaces of acrylic acid/1,7 octadiene: surface characterisation and the attachment of ROS 17/2.8 osteoblast-like cells.

    PubMed

    Daw, R; Candan, S; Beck, A J; Devlin, A J; Brook, I M; MacNeil, S; Dawson, R A; Short, R D

    1998-10-01

    The purpose of this study was: (a) to examine the effect of plasma-gas composition on plasma polymer oxygen/carbon (O/C) ratio, functional group composition and stability in water, and then (b) to examine cell attachment to surfaces containing different concentrations of O/C and functional groups. Oxygen-functionalised surfaces were deposited by means of the plasma copolymerisation of acrylic acid/1,7-octadiene. The use of a diluent hydrocarbon allowed the deposition of surfaces with a range of O/C concentrations. Plasma copolymer surfaces were characterised by X-ray photoelectron spectroscopy (XPS). Changes in functional group composition with % acrylic acid monomer and the non-dispersive and dispersive parts of the surface energy of these plasma copolymers were measured. The solubility of the plasma copolymers was assessed by means of XPS. The degree of attachment of ROS 17/2.8 osteoblast-like cells to plasma copolymer surfaces deemed to be 'stable' in aqueous medium was measured. Tissue culture polystyrene (TCPS) was included as a control. Attachment was found to be greatest to the plasma copolymer surface with an O/C of 0.11. This surface had a carboxylic acid concentration of ca. 3%. Attachment did not correlate with increased surface wettability (i.e. the non-dispersive component of the surface energy). PMID:9856582

  1. The role of PaAAC1 encoding a mitochondrial ADP/ATP carrier in the biosynthesis of extracellular glycolipids, mannosylerythritol lipids, in the basidiomycetous yeast Pseudozyma antarctica.

    PubMed

    Morita, Tomotake; Ito, Emi; Fukuoka, Tokuma; Imura, Tomohiro; Kitamoto, Dai

    2010-07-01

    Pseudozyma antarctica produces large amounts of the glycolipid biosurfactants known as mannosylerythritol lipids (MEL), which show not only excellent surface-active properties but also versatile biochemical actions. A gene homologous with a mitochondrial ADP/ATP carrier was dominantly expressed in P. antarctica under MEL-producing conditions on the basis of previous gene expression analysis. The gene encoding the mitochondrial ADP/ATP carrier of P. antarctica (PaAAC1) contained a putative open reading frame of 954 bp and encodes a polypeptide of 317 amino acids. The deduced translation product shared high identity of 66%, 70%, 69%, 74%, 75% and 52% with the mitochondrial ADP/ATP carrier of Saccharomyces cerevisiae (AAC1), S. cerevisiae (AAC2), S. cerevisiae (AAC3), Kluyveromyces lactis (KlAAC), Neurospora crassa (NcAAC) and human (ANT1), respectively, and conserved the consensus sequences of all ADP/ATP carrier proteins. The gene expression by introducing a plasmid pUXV1-PaAAC1 into the yeast cells increased the MEL production. In addition, the expression of PaAAC1 in which the conserved arginine and leucine required for ATP transport activity were replaced with isoleucine and serine, respectively, failed to increase MEL production. Accordingly, these results suggest that PaAAC1 encoding a mitochondrial ADP/ATP carrier should be involved in MEL biosynthesis in the yeast. PMID:20146402

  2. AAC Interventions for Autism: A Research Summary

    ERIC Educational Resources Information Center

    Nunes, Debora R. P.

    2008-01-01

    Fifty-six studies from 1980 to 2007 involving the use of augmentative and alternative communication (AAC) by individuals with autism were reviewed. The majority of the studies used single-subject research designs and emphasized language production skills. Many investigations were held in artificial language learning settings, and a few involved…

  3. Responses to the AAC and U Statement

    ERIC Educational Resources Information Center

    Hollinger, David A.; Neal, Anne D.; Robbins, Bruce

    2006-01-01

    Academic freedom is an institutionally specific type of liberty. It gains its character from the rules of evidence and reasoning used by communities of scientists and scholars to determine the relative value of truth-claims. One of the finest virtues of the Association of American Colleges and Universities (AAC&U) Statement on Academic Freedom and…

  4. Enhancing literacy development through AAC technologies.

    PubMed

    Sturm, Janet M; Erickson, Karen; Yoder, David E

    2002-01-01

    There is a critical need to understand teaching and technology supports that enable students who use augmentative and alternative communication (AAC) systems to engage in meaningful literacy experiences and foster conventional literacy skills. To thrive in classroom environments, they must have access to tools that can support them in active and independent literacy learning. These students need technology that allows them to move seamlessly between reading, writing, and communicating. They require technology that takes into account access needs, individual learning needs, the learning demands of technology, and literacy development across grades. Families and school teams need information that will assist them in providing the best tools and the most appropriate content within these tools throughout the school day. Teachers need information that supports them in providing exemplary literacy instruction to students who use AAC systems. This article explores and summarizes factors impacting literacy learning, including literacy capabilities of school-age students who use AAC, communication in literacy learning and use, reading and writing instruction in general education classrooms, and technology to support literacy learning. It is important that future technology tools provide a platform for levels of literacy learning: The power of technology will be reflected in its ability to provide access to and display the right content at the right time for students who use AAC. This article summarizes current factors thought to influence literacy learning and discusses priorities for future research and technology development. PMID:12739851

  5. Synthesis of lithium iron phosphate/carbon microspheres by using polyacrylic acid coated iron phosphate nanoparticles derived from iron(III) acrylate.

    PubMed

    Xu, Dongwei; He, Yan-Bing; Chu, Xiaodong; Ding, Zhaojun; Li, Baohua; He, Jianfu; Du, Hongda; Qin, Xianying; Kang, Feiyu

    2015-03-01

    Lithium iron phosphate/carbon (LiFePO4 /C) microspheres with high rate and cycling performance are synthesized from iron phosphate/polyacrylic acid (FePO4 /PAA) nanoparticles. Iron(III) acrylate is used as a precursor for both the iron and carbon sources. FePO4 nanoparticles are first produced by a coprecipitation reaction. The byproduct, acrylic acid ions, is polymerized in situ to form a uniform PAA layer on the surface of the FePO4 nanoparticles. The as-prepared LiFePO4 /C microspheres are composed of primary nanoparticles with sizes of 40-50 nm. The nanoparticles are fully coated with a thin, uniform carbon layer derived from the decomposition of the PAA layer. The uniform carbon-coating layer cooperates with interstitial and boundary carbon derived from sucrose successfully to construct an excellent interconnecting conductive network in the microspheres. As a result of the unique structure, the as-prepared LiFePO4 /C microspheres display both high electronic and ionic conductivities, which contribute to their high rate performance (162.9 mAh g(-1) at 0.1C and 126.1 mAh g(-1) at 5C) and excellent cycling stability (97.1% of capacity retention after 500 cycles at 5C/5C). PMID:25469674

  6. Poly (Acrylamide-co-Acrylic Acid) Hydrogel Induced by Glow-Discharge Electrolysis Plasma and Its Adsorption Properties for Cationic Dyes

    NASA Astrophysics Data System (ADS)

    Yu, Jie; Yang, Gege; Pan, Yuanpei; Lu, Quanfang; Yang, Wu; Gao, Jinzhang

    2014-08-01

    In this paper, poly (acrylamide-co-acrylic acid) (P(AM-co-AA)) hydrogel was prepared in an aqueous solution by using glow-discharge electrolysis plasma (GDEP) induced copolymerization of acrylamide (AM) and acrylic acid (AA), in which N,N'-methylenebisacrylamide (MBA) was used as a crosslinker. A mechanism for the synthesis of P(AM-co-AA) hydrogel was proposed. To optimize the synthesis condition, the following parameters were examined in detail: the discharge voltage, discharge time, the content of the crosslinker, and the mass ratio of AM to AA. The results showed that the optimum pH range for cationic dyes removal was found to be 5.0-10.0. The P(AM-co-AA) hydrogel exhibits a very high adsorption potential and the experimental adsorption capacities for Crystal violet (CV) and Methylene blue (MB) were 2974.3 mg/g and 2303.6 mg/g, respectively. The adsorption process follows a pseudo-second-order kinetic model. In addition, the adsorption mechanism of P(AM-co-AA) hydrogel for cationic dyes was also discussed.

  7. Synthesis and characterization of antigenic influenza A M2e protein peptide-poly(acrylic) acid bioconjugate and determination of toxicity in vitro

    PubMed Central

    Kilinc, Yasemin Budama; Akdeste, Zeynep Mustafaeva; Koc, Rabia Cakir; Bagirova, Melahat; Allahverdiyev, Adil

    2014-01-01

    The influenza A virus is a critical public health problem that causes epidemics and pandemics, and occurs widely all over the world. Various vaccines against the virus have not provided a solution to the problem. Different approaches, particularly M2e peptide–based vaccines, are available for developing universal vaccines against influenza A. However, it is important to select a suitable carrier to obtain an effective vaccine. Accordingly, studies on the usage of various carriers are ongoing. Particularly, polymer-based carriers have gained importance due to both drug delivery and adjuvant effects. Therefore, bioconjugate of the M2e protein peptide from the influenza A virus covalent bonded with poly(acrylic) acid was synthesized in our study for the first time. The characterization was performed using size-exclusion chromatography and fluorescence spectroscopy; subsequently, it was found that the bioconjugate of the examined lower doses (0.05 and 0.5 mg/ml) have no toxic effects on human cell lines. These results suggest that, in the future, the poly(acrylic) acid bioconjugate of the M2e peptide should be studied in vivo for universal vaccine development against the influenza A virus. PMID:25482080

  8. Synthesis and characterization of antigenic influenza A M2e protein peptide-poly(acrylic) acid bioconjugate and determination of toxicity in vitro.

    PubMed

    Kilinc, Yasemin Budama; Akdeste, Zeynep Mustafaeva; Koc, Rabia Cakir; Bagirova, Melahat; Allahverdiyev, Adil

    2014-01-01

    The influenza A virus is a critical public health problem that causes epidemics and pandemics, and occurs widely all over the world. Various vaccines against the virus have not provided a solution to the problem. Different approaches, particularly M2e peptide-based vaccines, are available for developing universal vaccines against influenza A. However, it is important to select a suitable carrier to obtain an effective vaccine. Accordingly, studies on the usage of various carriers are ongoing. Particularly, polymer-based carriers have gained importance due to both drug delivery and adjuvant effects. Therefore, bioconjugate of the M2e protein peptide from the influenza A virus covalent bonded with poly(acrylic) acid was synthesized in our study for the first time. The characterization was performed using size-exclusion chromatography and fluorescence spectroscopy; subsequently, it was found that the bioconjugate of the examined lower doses (0.05 and 0.5 mg/ml) have no toxic effects on human cell lines. These results suggest that, in the future, the poly(acrylic) acid bioconjugate of the M2e peptide should be studied in vivo for universal vaccine development against the influenza A virus. PMID:25482080

  9. Spray-dried powders of starch and crosslinked poly(acrylic acid) as carriers for nasal delivery of inactivated influenza vaccine.

    PubMed

    Coucke, D; Schotsaert, M; Libert, C; Pringels, E; Vervaet, C; Foreman, P; Saelens, X; Remon, J P

    2009-02-18

    Mucosal vaccination has several advantages over parenteral vaccination. In this study, viscosity-enhancing mucosal delivery systems for the induction of an adaptive immune response against viral antigen were investigated. Powder formulations based on spray-dried mixtures of starch (Amioca)/poly(acrylic acid) (Carbopol 974P) in different ratios were used as carriers of the viral antigen. A comparison of these formulations for intranasal delivery of heat-inactivated influenza virus combined with LTR192G adjuvant was made in vivo in a rabbit model. Individual rabbit sera were tested for seroconversion against hemagglutinin (HA), the major surface antigen of influenza. The powder vaccine formulations were able to induce systemic anti-HA IgG responses. The presence of Carbopol 974P improved the kinetics of the immune responses and the level of IgG titers in a dose-dependent way which was correlated with moderately irritating capacities of the formulation. In contrast, mucosal IgA responses were not detected. In conclusion, it was demonstrated that the use of bioadhesive carriers based on Amioca starch and poly(acrylic acid) facilitates the induction of a systemic anti-HA antibody response after intranasal vaccination with a whole virus influenza vaccine. PMID:19114075

  10. Water-soluble polymeric chemosensor for selective detection of Hg(2+) in aqueous solution using rhodamine-based modified poly(acrylamide-acrylic acid).

    PubMed

    Geng, Tong-Mou; Wu, Da-Yu

    2015-12-01

    We report the fabrication of a novel easily available turn-on fluorescent water-soluble polymeric chemosensor for Hg(2+) ions that was simply prepared by micellar free radical polymerization of a water-insoluble organic rhodamine-based Hg(2+)-recognizing monomer (GR6GH), with hydrophilic monomers acrylamide (AM) and acrylic acid (AA). The chemical structure of the polymeric sensor was characterized by FT-IR and (1)H NMR spectroscopy. The apparent viscosity average molecular weight Mη of poly(acrylamide-acrylic acid) [poly(AM-NaAA)] and the water-soluble polymeric chemosensor poly(AM-NaAA-GR6GH) were 1.76 × 10(6) and 6.84 × 10(4) g/mol, respectively. Because of its amphiphilic property, the water-soluble polymeric chemosensor can be used as a chemosensor in aqueous media. Upon addition of Hg(2+) ions to an aqueous solution of poly(AM-NaAA-GR6GH), fluorescence enhancements were observed instantly. Moreover, other metal ions did not induce obvious changes to the fluorescence spectra. This approach may provide an easily measurable and inherently sensitive method for Hg(2+) ion detection in environmental and biological applications. PMID:25808221

  11. Magnetic Solid-Phase Extraction Based on β-Cyclodextrins/Acrylic Acid Modified Magnetic Gelatin for Determination of Moxidectin in Milk Samples

    PubMed Central

    Shang, Yinzhu; Wang, Peng; Zhao, Xiaoya; Ye, Cheng; Guo, Shaofei

    2016-01-01

    β-Cyclodextrins/acrylic acid modified magnetic gelatin was prepared and then employed as the magnetic solid-phase extraction (MSPE) sorbent for extraction of moxidectin in milk samples. Due to the rigidity of hydrophobic cavity of β-cyclodextrins and carboxyl groups of acrylic acid, magnetic composites are prepared to form a complex with target molecules through various kinds of chemical reactions and then showed excellent extraction performance. This method exhibits the advantages of simplicity of implementation, short extraction time (5 min), low solvent consumption, and high extraction efficiency. A rapid, simple, and effective method for the analysis of moxidectin in milk samples was established by MSPE coupled with liquid chromatography-fluorescence detection. The limit of detection was 0.1 ng·mL−1 and the recoveries from milk samples were in the range of 93.8%–112.5%. The relative standard deviation was not higher than 6.4%. In conclusion, magnetic solid-phase extraction is a simple and robust preconcentration technique that can be coupled to other analytical methods for the quantitative determination of target molecules in complex samples. PMID:27437160

  12. Iron-Based Redox Polymerization of Acrylic Acid for Direct Synthesis of Hydrogel/Membranes, and Metal Nanoparticles for Water Treatment

    PubMed Central

    Hernández, Sebastián; Papp, Joseph K.; Bhattacharyya, Dibakar

    2014-01-01

    Functionalized polymer materials with ion exchange groups and integration of nano-structured materials is an emerging area for catalytic and water pollution control applications. The polymerization of materials such as acrylic acid often requires persulfate initiator and a high temperature start. However, is generally known that metal ions accelerate such polymerizations starting from room temperature. If the metal is properly selected, it can be used in environmental applications adding two advantages simultaneously. This paper deals with this by polymerizing acrylic acid using iron as accelerant and its subsequent use for nanoparticle synthesis in hydrogel and PVDF membranes. Characterizations of hydrogel, membranes and nanoparticles were carried out with different techniques. Nanoparticles sizes of 30–60 nm were synthesized. Permeability and swelling measurements demonstrate an inverse relationship between hydrogel mesh size (6.30 to 8.34 nm) and membrane pores (222 to 110 nm). Quantitative reduction of trichloroethylene/chloride generation by Fe/Pd nanoparticles in hydrogel/membrane platforms was also performed. PMID:24954975

  13. Copolymeric hexyl acrylate-methacrylic acid microspheres - surface vs. bulk reactive carboxyl groups. Coulometric and colorimetric determination and analytical applications for heterogeneous microtitration.

    PubMed

    Stelmach, Emilia; Maksymiuk, Krzysztof; Michalska, Agata

    2016-10-01

    Copolymeric acrylate microspheres were prepared from hexyl acrylate using different amounts of methacrylic acid, resulting in a series of microspheres of gradually changing properties. The distribution of carboxyl groups - between surface and bulk of microspheres was evaluated. Bulk reactive carboxyl groups were determined using reverse coulometric titration with H(+) ions, following hydroxide ions have been generated and allowed to react with microspheres in the first step. It was found that the number of reactive carboxyl groups available in copolymeric microspheres is lower compared to number of methacrylic acid units used for polymerization process. Moreover, there is correlation between the number of groups introduced and found to be reactive in microspheres. On the other hand, the number of surface reactive groups was proportional to the number of groups introduced in course of polymerization. Thus, the surface reactive groups can be used as reagent, in novel heterogeneous microtitration procedure, in which a constant number of microspheres of different carboxyl groups contents is introduced to the sample to react with the analyte. The applicability of novel proposed method was tested on the example of Ni(2+) determination. PMID:27474305

  14. Toward "stable-on-the-table" enzymes: improving key properties of catalase by covalent conjugation with poly(acrylic acid).

    PubMed

    Riccardi, Caterina M; Cole, Kyle S; Benson, Kyle R; Ward, Jessamyn R; Bassett, Kayla M; Zhang, Yiren; Zore, Omkar V; Stromer, Bobbi; Kasi, Rajeswari M; Kumar, Challa V

    2014-08-20

    Several key properties of catalase such as thermal stability, resistance to protease degradation, and resistance to ascorbate inhibition were improved, while retaining its structure and activity, by conjugation to poly(acrylic acid) (PAA, Mw 8000) via carbodiimide chemistry where the amine groups on the protein are appended to the carboxyl groups of the polymer. Catalase conjugation was examined at three different pH values (pH 5.0, 6.0, and 7.0) and at three distinct mole ratios (1:100, 1:500, and 1:1000) of catalase to PAA at each reaction pH. The corresponding products are labeled as Cat-PAA(x)-y, where x is the protein to polymer mole ratio and y is the pH used for the synthesis. The coupling reaction consumed about 60-70% of the primary amines on the catalase; all samples were completely water-soluble and formed nanogels, as evidenced by gel electrophoresis and electron microscopy. The UV circular dichroism (CD) spectra indicated substantial retention of protein secondary structure for all samples, which increased to 100% with increasing pH of the synthesis and polymer mole fraction. Soret CD bands of all samples indicated loss of ∼50% of band intensities, independent of the reaction pH. Catalytic activities of the conjugates increased with increasing synthesis pH, where 55-80% and 90-100% activity was retained for all samples synthesized at pH 5.0 and pH 7.0, respectively, and the Km or Vmax values of Cat-PAA(100)-7 did not differ significantly from those of the free enzyme. All conjugates synthesized at pH 7.0 were thermally stable even when heated to ∼85-90 °C, while native catalase denatured between 55 and 65 °C. All conjugates retained 40-90% of their original activities even after storing for 10 weeks at 8 °C, while unmodified catalase lost all of its activity within 2 weeks, under similar storage conditions. Interestingly, PAA surrounding catalase limited access to the enzyme from large molecules like proteases and significantly increased

  15. Graft copolymerization of acrylic acid to cassava starch--evaluation of the influences of process parameters by an experimental design method.

    PubMed

    Witono, J R; Noordergraaf, I W; Heeres, H J; Janssen, L P B M

    2012-11-01

    The graft copolymerization of cassava starch with acrylic acid was investigated using a free radical initiator system (Fe(2+)/H(2)O(2) redox system) in water. A comprehensive understanding of the important variables and their interaction has been obtained by applying an experimental design method. In this approach, two ('high' and 'low') values of selected variables are considered. Important result parameters are add-on and the grafting efficiency. Out of eight reaction variables, it was found that only temperature, starch concentration and the starch to monomer ratio have a pronounced influence on these response parameters. Moderate reaction temperature (40 °C) and high starch concentration (10%) give relatively good results of add-on and grafting efficiency. A low starch to monomer ratio favors add-on but decreases grafting efficiency. These findings can be used to optimize the production of cassava starch-acrylate copolymers and to gain insight in the process-product property interactions, for various applications. PMID:22944411

  16. Separation of poly(acrylic acid) salts according to topology using capillary electrophoresis in the critical conditions.

    PubMed

    Maniego, Alison R; Ang, Dale; Guillaneuf, Yohann; Lefay, Catherine; Gigmes, Didier; Aldrich-Wright, Janice R; Gaborieau, Marianne; Castignolles, Patrice

    2013-11-01

    Branching was detected in polyacrylates synthesised through radical polymerization via solution-state NMR, while inconsistencies have been reported for the determination of the molar mass of hydrophilic polyacrylates using aqueous-phase and organic-phase size-exclusion chromatography. In this work, poly(sodium acrylate)s, PNaAs, of various topologies were separated for the first time using free-solution capillary electrophoresis (CE). Free-solution CE does not separate the PNaAs by their molar mass, similarly to separations by liquid chromatography in the critical conditions, rather by different topologies (linear, star branched, and hyperbranched). The electrophoretic mobility of PNaAs increases as the degree of branching decreases. Separation is shown to be not only by the topology but also by the end groups as expected for a separation in the critical conditions: replacing a relatively bulky nitroxide end group with hydrogen atom yielded a higher electrophoretic mobility. This novel method, capillary electrophoresis in the critical conditions enabled, for the first time, the separation of hydrophilic polyacrylates according to their topology (branching) and their chain ends. This will allow meaningful and accurate characterization of their branched topologies as well as molar masses and progress in for advanced applications such as drug delivery or flocculation. PMID:23732867

  17. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... polymerized copolymer of ethyl acrylate, methyl methacrylate, and methacrylic acid applied in emulsion form to... Glyceryl monostearate Methyl cellulose Mineral oil Paraffin wax Potassium hydroxide Potassium...

  18. Preparation of porous carboxymethyl chitosan grafted poly (acrylic acid) superabsorbent by solvent precipitation and its application as a hemostatic wound dressing.

    PubMed

    Chen, Yu; Zhang, Yong; Wang, Fengju; Meng, Weiwei; Yang, Xinlin; Li, Peng; Jiang, Jianxin; Tan, Huimin; Zheng, Yongfa

    2016-06-01

    The volume phase transition of a hydrogel initiated by shrinking may result in complex patterns on its surface. Based on this unique property of hydrogel, we have developed a novel solvent precipitation method to prepare a kind of novel superabsorbent polymers with excellent hemostatic properties. A porous carboxymethyl chitosan grafted poly (acrylic acid) (CMCTS-g-PAA) superabsorbent polymer was prepared by precipitating CMCTS-g-PAA hydrogel with ethanol. Its potential application in hemostatic wound dressing was investigated. The results indicate that the modified superabsorbent polymer is non-cytotoxic. It showed a high swelling capacity and better hemostatic performance in the treatments of hemorrhage model of ear artery, arteria cruralis and spleen of the New Zealand white rabbit than the unmodified polymer and other commonly used clinic wound dressings. The hemostatic mechanism of the porous CMCTS-g-PAA polymer was also discussed. PMID:27040191

  19. Surfactant mediated synthesis of poly(acrylic acid) grafted xanthan gum and its efficient role in adsorption of soluble inorganic mercury from water.

    PubMed

    Pal, Abhijit; Majumder, Kunal; Bandyopadhyay, Abhijit

    2016-11-01

    Noble copolymers from xanthan gum (XG) and poly(acrylic acid) (PAA) were synthesised through surfactant mediated graft copolymerization. The copolymers were applied as a biosorbent for inorganic Hg(II) at higher concentration level (300ppm). The copolymers were characterized using different analytical techniques which showed, the grafting principally occurred across the amorphous region of XG. Measurement of zeta potential and hydrodynamic size indicated, the copolymers were strong polyanion and possessed greater hydrodynamic size (almost in all cases) than XG, despite a strong molecular degradation that took place simultaneously during grafting. In the dispersed form, all grades of the copolymer displayed higher adsorption capability than XG, however, the grade with maximum grafting produced the highest efficiency (68.03%). Manipulation produced further improvement in efficiency to 72.17% with the same copolymer after 75min at a pH of 5.0. The allowable biosorbent dose, however, was 1000ppm as determined from the experimental evidences. PMID:27516248

  20. Dynamics of the layer-by-layer assembly of a poly(acrylic acid)-lanthanide complex colloid and poly(diallyldimethyl ammonium).

    PubMed

    Xu, Jiali; Wang, Zhiliang; Wen, Lingang; Zhou, Xianju; Xu, Jian; Yang, Shuguang

    2016-01-21

    Poly(acrylic acid) (PAA) and lanthanide (Ln) ions, such as Ce(3+), Eu(3+), and Tb(3+), were prepared as dispersed complex colloidal particles through three different protocols with rigorous control of the pH value and mixing ratio. The negatively charged PAA-Ln complex particles were layer-by-layer (LbL) assembled with positively charged poly(diallyldimethyl ammonium) (PDDA) to prepare a thin film. The film thickness growth is much quicker than PDDA/PAA film. Due to the incorporation of Ln(3+) ions, the film exhibits fluorescence. During LbL assembly, PDDA-PAA association based on electrostatic force and PAA-Ce association based on coordination are in competition, which leads to the LbL assembly of PDDA and PAA-Ln complex colloidal particles being a complicated dynamic process. PMID:26549538

  1. A Novel Route for Preparing Highly Stable Fe3O4 Fluid with Poly(Acrylic Acid) as Phase Transfer Ligand

    NASA Astrophysics Data System (ADS)

    Oanh, Vuong Thi Kim; Lam, Tran Dai; Thu, Vu Thi; Lu, Le Trong; Nam, Pham Hong; Tam, Le The; Manh, Do Hung; Phuc, Nguyen Xuan

    2016-08-01

    Highly stable Fe3O4 liquid was synthesized by thermal decomposition using poly(acrylic acid) (PAA) as a phase transfer ligand. The crystalline structure, morphology, and magnetic properties of the as-prepared samples were thoroughly characterized. Results demonstrated that the magnetic Fe3O4 nanomaterial was formed in liquid phase with a spinel single-phase structure, average size of 8-13 nm, and high saturation magnetization (up to 75 emu/g). The PAA-capped Fe3O4 nanoparticles displayed high stability over a wide pH range (from 4 to 7) in 300 mM salt solution. More importantly, the heat-generating capacity of the nanoparticle systems was quantified at a specific absorption rate (SAR) of 70.22 W/g, which is 35% higher than magnetic nanoparticles coated with sodium dodecyl sulfate (SDS). These findings suggest the potential application of PAA-coated magnetic nanoparticles in magnetic hyperthermia.

  2. pH-sensing properties of cascaded long- and short-period fiber grating with poly acrylic acid/poly allylamine hydrochloride thin-film overlays

    NASA Astrophysics Data System (ADS)

    Yang, Ying

    2014-11-01

    Based on coupled-mode theory and transfer matrix method, the mode coupling mechanism and the reflection spectral properties of coated cascaded long- and short-period gratings (CLBG) are discussed. The effects of the thin-film parameters (film refractive index and film thickness) on the reflection spectra of the coated CLBG are simulated. By using electrostatic self-assembly method, poly acrylic acid (PAA) and poly allylamine hydrochloride (PAH) multilayer molecular pH-sensitive thin-films are assembled on the surface of the partial corroded CLBG. When the CLBG coated with PAA/PAH films are used to sense pH values, the resonant wavelengths of the CLBG have almost no shift, whereas the resonance peak reflectivities change with pH values. In addition, the sensitivities of the resonance peak reflectivities responding to pH values are improved by an order of magnitude.

  3. Hybrid polymeric hydrogels for ocular drug delivery: nanoparticulate systems from copolymers of acrylic acid-functionalized chitosan and N-isopropylacrylamide or 2-hydroxyethyl methacrylate

    NASA Astrophysics Data System (ADS)

    Barbu, Eugen; Verestiuc, Liliana; Iancu, Mihaela; Jatariu, Anca; Lungu, Adriana; Tsibouklis, John

    2009-06-01

    Nanoparticulate hybrid polymeric hydrogels (10-70 nm) have been obtained via the radical-induced co-polymerization of acrylic acid-functionalized chitosan with either N-isopropylacrylamide or 2-hydroxyethyl methacrylate, and the materials have been investigated for their ability to act as controlled release vehicles in ophthalmic drug delivery. Studies on the effects of network structure upon swelling properties, adhesiveness to substrates that mimic mucosal surfaces and biodegradability, coupled with in vitro drug release investigations employing ophthalmic drugs with differing aqueous solubilities, have identified nanoparticle compositions for each of the candidate drug molecules. The hybrid nanoparticles combine the temperature sensitivity of N-isopropylacrylamide or the good swelling characteristics of 2-hydroxyethyl methacrylate with the susceptibility of chitosan to lysozyme-induced biodegradation.

  4. Reusable nanocomposite of CoFe2O4/chitosan-graft-poly(acrylic acid) for removal of Ni(II) from aqueous solution

    NASA Astrophysics Data System (ADS)

    Nguyen, Van Cuong; Huynh, Thi Kim Ngoc

    2014-06-01

    In this paper, CoFe2O4/chitosan-graft-poly(acrylic acid) (CoFe2O4/CS-graft-PAA) nanocomposites were prepared successfully by coprecipitation of the compounds in alkaline solution and were used for removal of nickel (II) ions from aqueous solution. The sorption rate was affected significantly by the initial concentration of the solution, sorbent amount, and pH value of the solution. Batch experiments were conducted to investigate the adsorption capacity under different initial concentration (ranging from 25 to 150 mg L-1), solution pH (4.1, 5.3, 6.4 and 7.6), and contact time. These nanocomposites can be recycled conveniently from water with the assistance of an external magnet because of their exceptional properties. The prepared nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), x-ray powder diffraction (XRD), and thermogravimetric analysis (TGA).

  5. A Novel Route for Preparing Highly Stable Fe3O4 Fluid with Poly(Acrylic Acid) as Phase Transfer Ligand

    NASA Astrophysics Data System (ADS)

    Oanh, Vuong Thi Kim; Lam, Tran Dai; Thu, Vu Thi; Lu, Le Trong; Nam, Pham Hong; Tam, Le The; Manh, Do Hung; Phuc, Nguyen Xuan

    2016-05-01

    Highly stable Fe3O4 liquid was synthesized by thermal decomposition using poly(acrylic acid) (PAA) as a phase transfer ligand. The crystalline structure, morphology, and magnetic properties of the as-prepared samples were thoroughly characterized. Results demonstrated that the magnetic Fe3O4 nanomaterial was formed in liquid phase with a spinel single-phase structure, average size of 8-13 nm, and high saturation magnetization (up to 75 emu/g). The PAA-capped Fe3O4 nanoparticles displayed high stability over a wide pH range (from 4 to 7) in 300 mM salt solution. More importantly, the heat-generating capacity of the nanoparticle systems was quantified at a specific absorption rate (SAR) of 70.22 W/g, which is 35% higher than magnetic nanoparticles coated with sodium dodecyl sulfate (SDS). These findings suggest the potential application of PAA-coated magnetic nanoparticles in magnetic hyperthermia.

  6. Structural changes of polyacids initiated by their neutralization with various alkali metal hydroxides. Diffusion studies in poly(acrylic acid)s.

    PubMed

    Masiak, Michal; Hyk, Wojciech; Stojek, Zbigniew; Ciszkowska, Malgorzata

    2007-09-27

    The changes in the three-dimensional structure of the poly(acrylic acid), PAA, induced by incorporation of various alkali-metal counterions have been evaluated by studying diffusion of an uncharged probe (1,1'-ferrocenedimethanol) in the polymeric media. The studies are supported by the measurements of conductivity and viscosity of the polymeric media. Solutions of linear PAA of four different sizes (molecular weights: 450,000, 750,000, 1,250,000, 4,000,000) were neutralized with hydroxides of alkali metals of group 1 of the periodic table (Li, Na, K, Rb, Cs) to the desired neutralization degree. The transport properties of the obtained polyacrylates were monitored by measuring the changes in the probe diffusion coefficient during the titration of the polyacids. The probe diffusivity was determined from the steady-state current of the probe voltammetric oxidation at disk microelectrodes. Diffusivity of the probe increases with the increase in the degree of neutralization and with the increase in viscosity. It reaches the maximum value at about 60-80% of the polyacid neutralization. The way the probe diffusion coefficients change is similar in all polyacid solutions and gels. The increase in the size of a metal cation causes, in general, an enhancement in the transport of probe molecules. The biggest differences in the probe diffusivities are between lithium and cesium polyacrylates. The differences between the results obtained for cesium and rubidium are not statistically significant due to lack of good precision of the voltammetric measurements. The measurements of the electric conductivity of polyacrylates and the theoretical predictions supplemented the picture of electrostatic interactions between the polyanionic chains and the metal cations of increasing size. In all instances of the PAAs, the viscosity of the solutions rapidly increases in the 0-60% range of neutralization and then becomes constant in the 60-100% region. With the exception of the shortest

  7. Controlled release camptothecin tablets based on pluronic and poly(acrylic acid) copolymer. Effect of fabrication technique on drug stability, tablet structure, and release mode.

    PubMed

    Bromberg, Lev; Hatton, T Alan; Barreiro-Iglesias, Rafael; Alvarez-Lorenzo, Carmen; Concheiro, Angel

    2007-06-01

    Poly(ethylene oxide)-b-poly(propylene oxide)-b-(polyethylene oxide)-g-poly(acrylic acid), a graft-comb copolymer of Pluronic 127 and poly(acrylic acid) (Pluronic-PAA), was explored as an excipient for tablet dosage form of camptothecin (CPT). The tablets were prepared by either direct compression of the drug-polymer physical blend, suspension in ethanol followed by evaporation, or compression after kneading and characterized with respect to their physical structures, drug stability, and release behavior. Porosity and water uptake rate were strongly dependent on the fabrication procedure, ranking in the order: direct compression of physical blend > compression after suspension/evaporation in ethanol > compression after kneading. Tablets prepared by compression of physical blends swelled in water with a rapid surface gel layer formation that impeded swelling and disintegration of the tablets core. These tablets were able to sustain the CPT release for a period of time longer than those observed with the tablets made by either suspension/evaporation or kneading, which disintegrated within a few minutes. Despite the tablet disintegration, the CPT release was impeded for at least 6 hr, which was attributed to the ability of the Pluronic-PAA copolymers to form micellar aggregates at the hydrated surface of the particles. Physical mixing did not alter the fraction of CPT being in the pharmaceutically active lactone form, whilst the preparation of the tablets by the other two methods caused a significant reduction in the lactone form content. Tablets prepared from the physical blends demonstrated CPT release rates increasing with the pH due to the PAA ionization leading to the increase in the rate and extent of the tablet swelling. The results obtained demonstrate the potential of the Pluronic-PAA copolymers for the oral administration of chemotherapeutic agents. PMID:17613025

  8. Patterned Poly(acrylic acid) Brushes Containing Gold Nanoparticles for Peptide Detection by Surface-Assisted Laser Desorption/Ionization Mass Spectrometry.

    PubMed

    Sangsuwan, Arunee; Narupai, Benjaporn; Sae-ung, Pornpen; Rodtamai, Sasithon; Rodthongkum, Nadnudda; Hoven, Voravee P

    2015-11-01

    Patterned poly(acrylic acid) (PAA) brushes was successfully generated via photolithography and surface-initiated reversible addition-fragmentation chain transfer (RAFT) polymerization of acrylic acid as verified by water contact angle measurements and FT-IR analysis. The carboxyl groups of PAA brushes can act as reducing moieties for in situ synthesis of gold nanoparticles (AuNPs), without the use of additional reducing agent. The formation of AuNPs was confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy. The glass surface-modified by PAA brushes and immobilized with AuNPs (AuNPs-PAA) can be used as a substrate for SALDI-MS analysis, which is capable of detecting both small peptides having m/z ≤ 600 (glutathione) and large peptides having m/z ≥ 1000 (bradykinin, ICNKQDCPILE) without the interference from matrix signal suggesting that AuNPs were stably trapped within the PAA brushes and the carboxyl groups of PAA can serve as internal proton source. By employing AuNPs as the capture probe, the AuNPs-PAA substrate can selectively identify thiol-containing peptides from the peptide mixtures with LOD as low as 0.1 and 0.05 nM for glutathione and ICNKQDCPILE, respectively. An ability to selectively detect ICNKQDCPILE in a diluted human serum is also demonstrated. The patterned format together with its high sensitivity and selectivity render this newly developed substrate a potential platform for high-throughput analysis of other biomarkers, especially those with low molecular weight in complex biological samples. PMID:26434604

  9. The Acrylation of Glycerol: a Precursor to Functionalized Lipids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Didecanoylacryloylglycerol was synthesized from decanoic and acrylic acids and glycerol using K2O as catalyst. This reaction was carried out in hexane in a closed stainless steel reactor at 200°C for 5h. The reactants were added in a 1:3:4 glycerol:decanoic acid:acrylic acid molar ratio. The resu...

  10. Mesoporous silica nanoparticles with bilayer coating of poly(acrylic acid-co-itaconic acid) and human serum albumin (HSA): A pH-sensitive carrier for gemcitabine delivery.

    PubMed

    Pourjavadi, Ali; Tehrani, Zahra Mazaheri

    2016-04-01

    Novel bilayer coated mesoporous silica nanoparticle (MCM-41) based on pH sensitive poly(acrylic acid-co-itaconic acid) and human serum albumin (HSA) was designed for controlled delivery of gemcitabine (anticancer drug) to cancer cells. The shell around the mesoporous silica has bilayer structure. Poly(acrylic acid-co-itaconic acid) was used as pH-sensitive inner shell and human serum albumin, HSA, was used as outer shell. The core-shell structure was formed due to electrostatic interaction between ammonium groups of modified MCM-41 and carboxylate groups of copolymer. Also, the albumin layer was wrapped around the copolymer coated nanoparticle by electrostatic interaction between ammonium groups from protein and carboxylate ions of copolymer shell. Moreover, the maximum release occurred at pH 5.5 (pH of endosomes) because the bilayer shell collapsed at this pH. The drug nanocarrier would be a good candidate for tumor therapy due to its biocompatibility, controlled release and pH responsive behavior. PMID:26838909

  11. Radiation-initiated emulsion copolymerization of styrene and carboxylic acid monomers. [Gamma radiation

    SciTech Connect

    Egusa, S.; Makuuchi, K.

    1982-03-01

    The emulsion copolymerization of styrene and carboxylic acid monomers such as acrylic, methacrylic, and itaconic acids (AAc, MAAc, IAc) was studied by using /sup 60/Co ..gamma..-rays as initiator and sodium dodecylsulfate as emulsifier. The polymerization behavior of these acid monomers was followed by simultaneous conductometric and potentiometric titrations for a latex sample taken in polymerization. The polymerization rate of these acid monomers increases in the following order of hydrophobicity: IAc < AAc < MAAc; this suggests that their polymerization sites are mainly the surface and/or subsurface regions of latex particles. The copolymerization rate of styrene and acid monomer increases with an increase in the acid monomer content for AAc and MAAc, whereas for IAc the rate decreases. The particle sizes determined by the stopped-flow method reveal that this variation of copolymerization rate cannot be explained by the number of growing particles and should be attributed to another factor; for instance, the transfer rate of styrene molecules from oil droplets to growing particles.

  12. Transition Strategies for Adolescents and Young Adults Who Use AAC. AAC Series

    ERIC Educational Resources Information Center

    McNaughton, David B., Ed.; Beukelman, David R., Ed.

    2010-01-01

    To make a smooth transition to a fulfilling, self-determined adult life, young people who use Augmentative-Alternative Communication (AAC) need effective services that meet their individual needs and make the most of advances in technology. Professionals will provide these critical supports with the help of this book, the first complete guide to…

  13. Effect of sodium hypochlorite and peracetic acid on the surface roughness of acrylic resin polymerized by heated water for short and long cycles

    PubMed Central

    Sczepanski, Felipe; Sczepanski, Claudia Roberta Brunnquell; Berger, Sandrine Bittencourt; Consani, Rafael Leonardo Xediek; Gonini-Júnior, Alcides; Guiraldo, Ricardo Danil

    2014-01-01

    Objective: To evaluate the surface roughness of acrylic resin submitted to chemical disinfection via 1% sodium hypochlorite (NaClO) or 1% peracetic acid (C2H4O3). Materials and Methods: The disc-shaped resin specimens (30 mm diameter ×4 mm height) were polymerized by heated water using two cycles (short cycle: 1 h at 74°C and 30 min at 100°C; conventional long cycle: 9 h at 74°C). The release of substances by these specimens in water solution was also quantified. Specimens were fabricated, divided into four groups (n = 10) depending on the polymerization time and disinfectant. After polishing, the specimens were stored in distilled deionized water. Specimens were immersed in 1% NaClO or 1% C2H4O3 for 30 min, and then were immersed in distilled deionized water for 20 min. The release of C2H4O3 and NaClO was measured via visual colorimetric analysis. Roughness was measured before and after disinfection. Roughness data were subjected to two-way ANOVA and Tukey's test. Results: There was no interaction between polymerization time and disinfectant in influencing the average surface roughness (Ra, P = 0.957). Considering these factors independently, there were significant differences between short and conventional long cycles (P = 0.012), but no significant difference between the disinfectants hypochlorite and C2H4O3 (P = 0.366). Visual colorimetric analysis did not detect release of substances. Conclusion: It was concluded that there was the difference in surface roughness between short and conventional long cycles, and disinfection at acrylic resins polymerized by heated water using a short cycle modified the properties of roughness. PMID:25512737

  14. Adolescence and AAC: Intervention Challenges and Possible Solutions

    ERIC Educational Resources Information Center

    Smith, Martine M.

    2015-01-01

    Adolescence is a unique developmental period, spanning the gulf between childhood and adulthood. For adolescents who use augmentative and alternative communication (AAC), the major physical, cognitive, linguistic, social, and emotional changes associated with adolescence may have significant implications for their use of AAC. These challenges are…

  15. ALKALI-ACTIVATED CEMENT (AAC) AS A SUSTAINABLE BUILDING MATERIAL

    EPA Science Inventory

    It is expected that this project will result in 1) production of technical paper(s) and presentations that better explains the relationships between chemical, microstructural, and performance properties of AACs, 2) commercially viable AAC formulae that pass the ASTM C1157 stan...

  16. AAC Strategies for Individuals with Moderate to Severe Disabilities

    ERIC Educational Resources Information Center

    Johnston, Susan S.; Reichle, Joe; Feeley, Kathleen M.; Jones, Emily A.

    2012-01-01

    With more children and young adults with severe disabilities in today's general education classrooms, SLPs and other professionals must be ready to support their students' communication skills with effective AAC. They'll get the proven strategies they need with this intervention guide from top AAC experts, ideal for use as an in-service…

  17. Microwave-assisted synthesis of biocompatible europium-doped calcium hydroxyapatite and fluoroapatite luminescent nanospindles functionalized with poly(acrylic acid).

    PubMed

    Escudero, Alberto; Calvo, Mauricio E; Rivera-Fernández, Sara; de la Fuente, Jesús M; Ocaña, Manuel

    2013-02-12

    Europium-doped calcium hydroxyapatite and fluoroapatite nanophosphors functionalized with poly(acrylic acid) (PAA) have been synthesized through a one-pot microwave-assisted hydrothermal method from aqueous basic solutions containing calcium nitrate, sodium phosphate monobasic, and PAA, as well as sodium fluoride in the case of the fluoroapatite particles. In both cases a spindlelike morphology was obtained, resulting from an aggregation process of smaller subunits which also gave rise to high specific surface area. The size of the nanospindles was 191 (32) × 40 (5) nm for calcium hydroxyapatite and 152 (24) × 38 (6) nm for calcium fluoroapatite. The luminescent nanoparticles showed the typical red luminescence of Eu(3+), which was more efficient for the fluoroapatite particles than for the hydroxyapatite. This is attributed to the presence of OH(-) quenchers in the latter. The nanophosphors showed negligible toxicity for Vero cells. Both PAA-functionalized nanophosphors showed a very high (up to at least 1 week) colloidal stability in 2-(N-morpholino)ethanesulfonic acid (MES) at pH 6.5, which is a commonly used buffer for physiological pH. All these features make both kinds of apatite-based nanoparticles promising tools for biomedical applications, such as luminescent biolabels and tracking devices in drug delivery systems. PMID:23317411

  18. A novel pulsatile drug delivery system based on the physiochemical reaction between acrylic copolymer and organic acid: in vitro and in vivo evaluation.

    PubMed

    Zhang, Ziwei; Qi, Xiaole; Li, Xiangbo; Xing, Jiayu; Zhu, Xuehua; Wu, Zhenghong

    2014-02-28

    Multilayer-coating technology is the traditional method to achieve pulsatile drug release with the drawbacks of time consuming, more materials demanding and lack of efficiency. The purpose of this study was to design a novel pulsatile drug delivery system based on the physiochemical interaction between acrylic copolymer and organic acid with relatively simpler formulation and manufacturing process. The Enalapril Maleate (EM) pulsatile release pellets were prepared using extruding granulation, spheronization and fluid-bed coating technology. The ion-exchange experiment, hydration study and determination of glass transition temperature were conducted to explore the related drug release mechanism. Bioavailability experiment was carried out by administering the pulsatile release pellets to rats compared with marketed rapid release tablets Yisu. An obvious 4h lag time period and rapid drug release was observed from in vitro dissolution profiles. The release mechanism was a combination of both disassociated and undisassociated forms of succinic acid physiochemically interacting with Eudragit RS. The AUC0-τ of the EM pulsatile pellets and the market tablets was 702.384 ± 96.89 1 hn g/mL and 810.817 ± 67.712 h ng/mL, while the relative bioavailability was 86.62%. These studies demonstrate this novel pulsatile release concept may be a promising strategy for oral pulsatile delivery system. PMID:24368107

  19. A study of the swelling and model protein release behaviours of radiation-formed poly(N-vinyl 2-pyrrolidone-co-acrylic acid) hydrogels

    NASA Astrophysics Data System (ADS)

    Wang, David; Hill, David J. T.; Rasoul, Firas; Whittaker, Andrew K.

    2011-02-01

    Hydrogels were prepared from poly(acrylic acid-co-N-vinyl pyrrolidone), poly(AA-co-VP) and mixtures of poly(AA-co-VP) and poly(ethylene oxide), PEO, by gamma radiolysis of aqueous solutions of the AA and VP monomers containing ethylene glycol dimethacrylate, EGDMA, as crosslinker and PEO. The AA/VP composition range of the poly(AA-co-VP) was XAA 0.7-0.9. The swelling behaviours of the hydrogels from the dry state were investigated in water (pH 6.5) and 50 mM 4-(2-hydroxyethyl)piperazine-1-ethylsulfonic acid buffer, HEPES buffer, at pH 7.4 and 295 K. The effects of poly(AA-co-VP) composition, crosslinker mole fraction and the presence of PEO on the equilibrium swelling ratio for the gels was examined. The kinetics of the release of a model protein, horseradish peroxidase, HRP, from the hydrogels in water were also studied at 295 K.

  20. Identification and characterization of a novel aac(6')-Iag associated with the blaIMP-1-integron in a multidrug-resistant Pseudomonas aeruginosa.

    PubMed

    Kobayashi, Kanao; Hayashi, Ikue; Kouda, Syuntaro; Kato, Fuminori; Fujiwara, Tamaki; Kayama, Shizuo; Hirakawa, Hideki; Itaha, Hideyuki; Ohge, Hiroki; Gotoh, Naomasa; Usui, Tsuguru; Matsubara, Akio; Sugai, Motoyuki

    2013-01-01

    In a continuing study from Dec 2006 to Apr 2008, we characterized nine multi-drug resistant Pseudomonas aeruginosa strains isolated from four patients in a ward at the Hiroshima University Hospital, Japan. Pulsed-field gel electrophoresis of SpeI-digested genomic DNAs from the isolates suggested the clonal expansion of a single strain; however, only one strain, NK0009, was found to produce metallo-β-lactamase. PCR and subsequent sequencing analysis indicated NK0009 possessed a novel class 1 integron, designated as In124, that carries an array of four gene cassettes: a novel aminoglycoside (AG) resistance gene, aac(6')-Iag, blaIMP-1, a truncated form of blaIMP-1, and a truncated form of aac(6')-Iag. The aac(6')-Iag encoded a 167-amino-acid protein that shows 40% identity with AAC(6')-Iz. Recombinant AAC(6')-Iag protein showed aminoglycoside 6'-N-acetyltransferase activity using thin-layer chromatography (TLC) and MS spectrometric analysis. Escherichia coli carrying aac(6')-Iag showed resistance to amikacin, arbekacin, dibekacin, isepamicin, kanamycin, sisomicin, and tobramycin; but not to gentamicin. A conjugation experiment and subsequent Southern hybridization with the gene probes for blaIMP-1 and aac(6')-Ig strongly suggested In124 is on a conjugal plasmid. Transconjugants acquired resistance to gentamicin and were resistant to virtually all AGs, suggesting that the In124 conjugal plasmid also possesses a gene conferring resistance to gentamicin. PMID:23950962

  1. Learning to Use Augmentative and Alternative Communication (AAC): Is There a Mentoring Role for Adults Experienced in Using AAC?

    ERIC Educational Resources Information Center

    Ballin, Liora; Balandin, Susan; Togher, Leanne; Stancliffe, Roger J.

    2009-01-01

    Augmentative and alternative communication (AAC), including speech generating devices (SGDs), offer people with complex communication needs the potential for improved communication and participation in society. Despite rapid and ongoing development in AAC technology, its potential is not being fully realised. The number of people with complex…

  2. Application of pH-responsive poly(2-dimethyl-aminoethylmethacrylate)-block-poly(acrylic acid) coatings for the open-tubular capillary electrochromatographic analysis of acidic and basic compounds.

    PubMed

    Sepehrifar, Roshanak; Boysen, Reinhard I; Danylec, Basil; Yang, Yuanzhong; Saito, Kei; Hearn, Milton T W

    2016-04-21

    A new type of stimuli-responsive polymeric (SRP) coating has been prepared for use in open tubular capillary electrochromatography (OT-CEC), by grafting poly(2-dimethylaminoethylmethacrylate)-block-poly(acrylic acid) (PDMAEMA-b-PAA) as a Y-shaped block copolymer with two dissimilar chain compositions onto the inner walls of aminopropyl-modified silica capillaries. The grafting process introduced weakly charged functional groups from the PAA and PDMAEMA, enabling the generation of electroendosmotic flow with magnitude and direction adjustable by changing the pH of the running buffer electrolyte. This stimuli-responsive PDMAEMA-b-PAA block copolymer was found to provide excellent resolution of various acidic and basic compounds, leading to efficient analyte separation. When operated in the OT-CEC mode, separation selectivities could be readily manipulated via differential contributions from chromatographic and electrophoretic mechanisms, simply by changing the pH or the ionic strength of the running buffer electrolyte. PMID:27026608

  3. Study of the adhesive properties versus stability/aging of hernia repair meshes after deposition of RF activated plasma polymerized acrylic acid coating.

    PubMed

    Rivolo, Paola; Nisticò, Roberto; Barone, Fabrizio; Faga, Maria Giulia; Duraccio, Donatella; Martorana, Selanna; Ricciardi, Serena; Magnacca, Giuliana

    2016-08-01

    In order to confer adhesive properties to commercial polypropylene (PP) meshes, a surface plasma-induced deposition of poly-(acrylic acid) (PPAA) is performed. Once biomaterials were functionalized, different post-deposition treatments (i.e. water washing and/or thermal treatments) were investigated with the aim of monitoring the coating degradation (and therefore the loss of adhesion) after 3months of aging in both humid/oxidant (air) and inert (nitrogen) atmospheres. A wide physicochemical characterization was carried out in order to evaluate the functionalization effectiveness and the adhesive coating homogeneity by means of static water drop shape analysis and several spectroscopies (namely, FTIR, UV-Visible and X-ray Photoemission Spectroscopy). The modification of the adhesion properties after post-deposition treatments as well as aging under different storage atmospheres were investigated by means of Atomic Force Microscopy (AFM) used in Force/Distance (F/D) mode. This technique confirms itself as a powerful tool for unveiling the surface adhesion capacity as well as the homogeneity of the functional coatings along the fibers. Results obtained evidenced that post-deposition treatments are mandatory in order to remove all oligomers produced during the plasma-treatment, whereas aging tests evidenced that these devices can be simply stored in presence of air for at least three months without a meaningful degradation of the original properties. PMID:27157754

  4. Fabrication of magnetic hydroxypropyl cellulose-g-poly(acrylic acid) porous spheres via Pickering high internal phase emulsion for removal of Cu(2+) and Cd(2.).

    PubMed

    Zhu, Yongfeng; Zheng, Yian; Zong, Li; Wang, Feng; Wang, Aiqin

    2016-09-20

    A series of magnetic hydroxypropyl cellulose-g-poly(acrylic acid) porous spheres were prepared via O/W Pickering high internal phase emulsions (HIPEs) integrated precipitation polymerization. The structure and composition of modified Fe3O4 and porous structures were characterized by TEM, XRD, TGA and SEM. The results indicated that the silanized Fe3O4 can influence greatly the pore structure of magnetic porous sphere in addition to non-negligible impacts of the proportion of mixed solvent and co-surfactant. The adsorption experiment demonstrated that the adsorption equilibrium can be reached within 40min and the maximal adsorption capacity was 300.00mg/g for Cd(2+) and 242.72mg/g for Cu(2+), suggesting its fast adsorption kinetics and high adsorption capacity. After five adsorption-desorption cycles, no significant changes in the adsorption capacity were observed, suggesting its excellent reusability. The magnetic porous sphere can be easily separated from the solution and then find its potential as a recyclable material for highly efficient removal of heavy metals. PMID:27261748

  5. Structural tailoring of hydrogen-bonded poly(acrylic acid)/poly(ethylene oxide) multilayer thin films for reduced gas permeability.

    PubMed

    Xiang, Fangming; Ward, Sarah M; Givens, Tara M; Grunlan, Jaime C

    2015-02-01

    Hydrogen bonded poly(acrylic acid) (PAA)/poly(ethylene oxide) (PEO) layer-by-layer assemblies are highly elastomeric, but more permeable than ionically bonded thin films. In order to expand the use of hydrogen-bonded assemblies to applications that require a better gas barrier, the effect of assembling pH on the oxygen permeability of PAA/PEO multilayer thin films was investigated. Altering the assembling pH leads to significant changes in phase morphology and bonding. The amount of intermolecular hydrogen bonding between PAA and PEO is found to increase with increasing pH due to reduction of COOH dimers between PAA chains. This improved bonding leads to smaller PEO domains and lower gas permeability. Further increasing the pH beyond 2.75 results in higher oxygen permeability due to partial deprotonation of PAA. By setting the assembling pH at 2.75, the negative impacts of COOH dimer formation and PAA ionization on intermolecular hydrogen bonding can be minimized, leading to a 50% reduction in the oxygen permeability of the PAA/PEO thin film. A 20 bilayer coating reduces the oxygen transmission rate of a 1.58 mm natural rubber substrate by 20 ×. These unique nanocoatings provide the opportunity to impart a gas barrier to elastomeric substrates without altering their mechanical behavior. PMID:25519816

  6. “Stable-on-the-Table” Biosensors: Hemoglobin-Poly (Acrylic Acid) Nanogel BioElectrodes with High Thermal Stability and Enhanced Electroactivity

    PubMed Central

    Ghimire, Ananta; Zore, Omkar V.; Thilakarathne, Vindya K.; Briand, Victoria A.; Lenehan, Patrick J.; Lei, Yu; Kasi, Rajeswari M.; Kumar, Challa V.

    2015-01-01

    In our efforts toward producing environmentally responsible but highly stable bioelectrodes with high electroactivities, we report here a simple, inexpensive, autoclavable high sensitivity biosensor based on enzyme-polymer nanogels. Met-hemoglobin (Hb) is stabilized by wrapping it in high molecular weight poly(acrylic acid) (PAA, MW 450k), and the resulting nanogels abbreviated as Hb-PAA-450k, withstood exposure to high temperatures for extended periods under steam sterilization conditions (122 °C, 10 min, 17–20 psi) without loss of Hb structure or its peroxidase-like activities. The bioelectrodes prepared by coating Hb-PAA-450k nanogels on glassy carbon showed well-defined quasi-reversible redox peaks at −0.279 and −0.334 V in cyclic voltammetry (CV) and retained >95% electroactivity after storing for 14 days at room temperature. Similarly, the bioelectrode showed ~90% retention in electrochemical properties after autoclaving under steam sterilization conditions. The ultra stable bioelectrode was used to detect hydrogen peroxide and demonstrated an excellent detection limit of 0.5 μM, the best among the Hb-based electrochemical biosensors. This is the first electrochemical demonstration of steam-sterilizable, storable, modular bioelectrode that undergoes reversible-thermal denaturation and retains electroactivity for protein based electrochemical applications. PMID:26393601

  7. Poly(acrylic acid)-regulated Synthesis of Rod-Like Calcium Carbonate Nanoparticles for Inducing the Osteogenic Differentiation of MC3T3-E1 Cells.

    PubMed

    Yang, Wei; Yao, Chenxue; Cui, Zhengyang; Luo, Dandan; Lee, In-Seop; Yao, Juming; Chen, Cen; Kong, Xiangdong

    2016-01-01

    Calcium carbonate, especially with nanostructure, has been considered as a good candidate material for bone regeneration due to its excellent biodegradability and osteoconductivity. In this study, rod-like calcium carbonate nanoparticles (Rod-CC NPs) with desired water dispersibility were achieved with the regulation of poly (acrylic acid). Characterization results revealed that the Rod-CC NPs had an average length of 240 nm, a width of 90 nm with an average aspect ratio of 2.60 and a negative ζ-potential of -22.25 ± 0.35 mV. The degradation study illustrated the nanoparticles degraded 23% at pH 7.4 and 45% at pH 5.6 in phosphate-buffered saline (PBS) solution within three months. When cultured with MC3T3-E1 cells, the Rod-CC NPs exhibited a positive effect on the proliferation of osteoblast cells. Alkaline phosphatase (ALP) activity assays together with the osteocalcin (OCN) and bone sialoprotein (BSP) expression observations demonstrated the nanoparticles could induce the differentiation of MC3T3-E1 cells. Our study developed well-dispersed rod-like calcium carbonate nanoparticles which have great potential to be used in bone regeneration. PMID:27164090

  8. Covalent immobilization of redox enzyme on electrospun nonwoven poly(acrylonitrile-co-acrylic acid) nanofiber mesh filled with carbon nanotubes: a comprehensive study.

    PubMed

    Wang, Zhen-Gang; Ke, Bei-Bei; Xu, Zhi-Kang

    2007-07-01

    In this work, novel conductive composite nanofiber mesh possessing reactive groups was electrospun from solutions containing poly(acrylonitrile-co-acrylic acid) (PANCAA) and multi-walled carbon nanotubes (MWCNTs) for redoxase immobilization, assuming that the incorporated MWCNTs could behave as electrons transferor during enzyme catalysis. The covalent immobilization of catalase from bovine liver on the neat PANCAA nanofiber mesh or the composite one was processed in the presence of EDC/NHS. Results indicated that both the amount and activity retention of bound catalase on the composite nanofiber mesh were higher than those on the neat PANCAA nanofiber mesh, and the activity increased up to 42%. Kinetic parameters, K(m) and V(max), for the catalases immobilized on the composite nanofiber mesh were lower and higher than those on the neat one, respectively. This enhanced activity might be ascribed to either promoted electron transfer through charge-transfer complexes and the pi system of carbon nanotubes or rendered biocompatibility by modified MWCNTs. Furthermore, the immobilized catalases revealed much more stability after MWCNTs were incorporated into the polymer nanofiber mesh. However, there was no significant difference in optimum pH value and temperature, thermal stability and operational stability between these two immobilized preparations, while the two ones appeared more advantageous than the free in these properties. The effect of MWCNTs incorporation on another redox enzyme, peroxidase, was also studied and it was found that the activity increased by 68% in comparison of composite one with neat preparation. PMID:17171660

  9. Design, Synthesis and Biological Evaluation of N4-Sulfonamido-Succinamic, Phthalamic, Acrylic and Benzoyl Acetic Acid Derivatives as Potential DPP IV Inhibitors

    PubMed Central

    Khalaf, Reema Abu; Sheikha, Ghassan Abu; Al-Sha'er, Mahmoud; Taha, Mutasem

    2013-01-01

    As incidence rate of type II diabetes mellitus continues to rise, there is a growing need to identify novel therapeutic agents with improved efficacy and reduced side effects. Dipeptidyl peptidase IV (DPP IV) is a multifunctional protein involved in many physiological processes. It deactivates the natural hypoglycemic incretin hormone effect. Inhibition of this enzyme increases endogenous incretin level, incretin activity and should restore glucose homeostasis in type II diabetic patients making it an attractive target for the development of new antidiabetic drugs. One of the interesting reported anti- DPP IV hits is Gemifloxacin which is used as a lead compound for the development of new DPP IV inhibitors. In the current work, design and synthesis of a series of N4-sulfonamido-succinamic, phthalamic, acrylic and benzoyl acetic acid derivatives was carried out. The synthesized compounds were evaluated for their in vitro anti-DPP IV activity. Some of them have shown reasonable bioactivity, where the most active one 17 was found to have an IC50 of 33.5 μM. PMID:24358058

  10. Poly(acrylic acid)-modified Fe3O4 microspheres for magnetic-targeted and pH-triggered anticancer drug delivery.

    PubMed

    Kang, Xiao-Jiao; Dai, Yun-Lu; Ma, Ping-An; Yang, Dong-Mei; Li, Chun-Xia; Hou, Zhi-Yao; Cheng, Zi-Yong; Lin, Jun

    2012-12-01

    Monodisperse poly(acrylic acid)-modified Fe(3)O(4) (PAA@Fe(3)O(4)) hybrid microspheres with dual responses (magnetic field and pH) were successfully fabricated. The PAA polymer was encapsulated into the inner cavity of Fe(3)O(4) hollow spheres by a vacuum-casting route and photo-initiated polymerization. TEM images show that the samples consist of monodisperse porous spheres with a diameter around 200 nm. The Fe(3)O(4) spheres, after modification with the PAA polymer, still possess enough space to hold guest molecules. We selected doxorubicin (DOX) as a model drug to investigate the drug loading and release behavior of as-prepared composites. The release of DOX molecules was strongly dependent on the pH value due to the unique property of PAA. The HeLa cell-uptake process of DOX-loaded PAA@Fe(3)O(4) was observed by confocal laser scanning microscopy (CLSM). After being incubated with HeLa cells under magnet magnetically guided conditions, the cytotoxtic effects of DOX-loaded PAA@Fe(3)O(4) increased. These results indicate that pH-responsive magnetic PAA@Fe(3)O(4) spheres have the potential to be used as anticancer drug carriers. PMID:23080514

  11. pH-responsive drug delivery system based on luminescent CaF(2):Ce(3+)/Tb(3+)-poly(acrylic acid) hybrid microspheres.

    PubMed

    Dai, Yunlu; Zhang, Cuimiao; Cheng, Ziyong; Ma, Ping'an; Li, Chunxia; Kang, Xiaojiao; Yang, Dongmei; Lin, Jun

    2012-03-01

    In this study, we design a controlled release system based on CaF(2):Ce(3+)/Tb(3+)-poly(acrylic acid) (PAA) composite microspheres, which were fabricated by filling the pH-responsive PAA inside CaF(2):Ce(3+)/Tb(3+) hollow spheres via photopolymerization route. The CaF(2):Ce(3+)/Tb(3+) hollow spheres prepared by hydrothermal route possess mesoporous structure and show strong green fluorescence from Tb(3+) under UV excitation. Doxorubicin hydrochloride (DOX), a widely used anti-cancer drug, was used as a model drug to evaluate the loading and controlled release behaviors of the composite microspheres due to the good biocompatibility of the samples using MTT assay. The composite carriers provide a strongly pH-dependent drug release behavior owing to the intrinsic property of PAA and its interactions with DOX. The endocytosis process of drug-loaded microspheres was observed using confocal laser scanning microscopy (CLSM) and the in vitro cytotoxic effect against SKOV3 ovarian cancer cells of the DOX-loaded carriers was investigated. In addition, the extent of drug release could be monitored by the altering of photoluminescence (PL) intensity of CaF(2):Ce(3+)/Tb(3+). Considering the good biocompatibility, high drug loading content and pH-dependent drug release of the materials, these hybrid luminescent microspheres have potential applications in drug controlled release and disease therapy. PMID:22196902

  12. Poly(acrylic acid) modified lanthanide-doped GdVO4 hollow spheres for up-conversion cell imaging, MRI and pH-dependent drug release.

    PubMed

    Kang, Xiaojiao; Yang, Dongmei; Dai, Yunlu; Shang, Mengmeng; Cheng, Ziyong; Zhang, Xiao; Lian, Hongzhou; Ma, Ping'an; Lin, Jun

    2013-01-01

    In this study, multifunctional poly(acrylic acid) modified lanthanide-doped GdVO(4) nanocomposites [PAA@GdVO(4): Ln(3+) (Ln = Yb/Er, Yb/Ho, Yb/Tm)] were constructed by filling PAA hydrogel into GdVO(4) hollow spheres via photoinduced polymerization. The up-conversion (UC) emission colors (green, red and blue) can be tuned by changing the codopant compositions in the matrices. The composites have potential applications as bio-probes for cell imaging. Meanwhile, the hybrid spheres can act as T(1) contrast agents for magnetic resonance imaging (MRI) owing to the existence of Gd(3+) ions on the surface of composites. Due to the nature of PAA, DOX-loaded PAA@GdVO(4):Yb(3+)/Er(3+) system exhibits pH-dependent drug releasing kinetics. A lower pH offers a faster drug release rate. Such character makes the loaded DOX easily released at cancer cells. The cell uptake process of drug-loaded composites was observed by using confocal laser scanning microscopy (CLSM). The results indicate the potential application of the multifunctional composites as theragnostics (effective bimodal imaging probes and pH-responsive drug carriers). PMID:23154448

  13. Ultrasonic Velocity, Viscosity and Refractive Index Investigation on Interacting Blend Solutions of PAA (Poly Acrylic Acid) and PVA (Poly Vinyl Alcohol) in Solvent DMSO (Di methyl Sulphoxide)

    NASA Astrophysics Data System (ADS)

    Nagamani, Chakrala

    2010-11-01

    The present study provides a great insight into the major new research areas like Plasma research (which is yielding a greater understanding of the universe) and Nano Technology Research (which provides many practical uses like Drug Delivery System). The Ultrasonic Velocities, Viscosities and Refractive indices of Poly (Acrylic Acid) and Poly (Vinyl Alcohol) blends in DMSO solutions have been measured over a wide range of composition, concentration and at different temperatures. The variation of Ultrasonic Velocity, derived acoustical parameters, adiabatic compressibility, acoustic impedance, Rao number, molar compressibility and relaxation strength with composition of blend solution was found not linear. This non-linearity has been attributed to incompatibility in conformity with the earlier findings. This behavior was confirmed by Viscometric and interaction parameters studies, as well as by investigation of Refractive index studies. These investigations offer an entirely new and simple approach to the study of the compatibility of polymer blends which is in general obtained by sophisticated techniques of thermal dynamic mechanical and electron microscopic analysis.

  14. "Stable-on-the-Table" Biosensors: Hemoglobin-Poly (Acrylic Acid) Nanogel BioElectrodes with High Thermal Stability and Enhanced Electroactivity.

    PubMed

    Ghimire, Ananta; Zore, Omkar V; Thilakarathne, Vindya K; Briand, Victoria A; Lenehan, Patrick J; Lei, Yu; Kasi, Rajeswari M; Kumar, Challa V

    2015-01-01

    In our efforts toward producing environmentally responsible but highly stable bioelectrodes with high electroactivities, we report here a simple, inexpensive, autoclavable high sensitivity biosensor based on enzyme-polymer nanogels. Met-hemoglobin (Hb) is stabilized by wrapping it in high molecular weight poly(acrylic acid) (PAA, M(W) 450k), and the resulting nanogels abbreviated as Hb-PAA-450k, withstood exposure to high temperatures for extended periods under steam sterilization conditions (122 °C, 10 min, 17-20 psi) without loss of Hb structure or its peroxidase-like activities. The bioelectrodes prepared by coating Hb-PAA-450k nanogels on glassy carbon showed well-defined quasi-reversible redox peaks at -0.279 and -0.334 V in cyclic voltammetry (CV) and retained >95% electroactivity after storing for 14 days at room temperature. Similarly, the bioelectrode showed ~90% retention in electrochemical properties after autoclaving under steam sterilization conditions. The ultra stable bioelectrode was used to detect hydrogen peroxide and demonstrated an excellent detection limit of 0.5 μM, the best among the Hb-based electrochemical biosensors. This is the first electrochemical demonstration of steam-sterilizable, storable, modular bioelectrode that undergoes reversible-thermal denaturation and retains electroactivity for protein based electrochemical applications. PMID:26393601

  15. pH- and ionic-strength-induced structural changes in poly(acrylic acid)-lipid-based self-assembled materials.

    SciTech Connect

    Crisci, A.; Hay, D. N. T.; Seifert, S.; Firestone, M. A.

    2009-01-01

    The effect of a polyanion introduced as a lipid conjugate (poly(acrylic acid)- dimyristoyl-sn-glycero-3-phosphoethanolamine, PAA-DMPE) on the structure of a self-assembled, biomembrane mimetic has been evaluated using synchrotron small-angle X-ray scattering (SAXS). At high grafting density (8-11 mol.%), the PAA chains were found to produce significant changes in structure in response to changes in pH and electrolyte composition. At low pH and in the absence of salt (NaCl), the neutral PAA chains adopt a coil conformational state that leads to the formation of a swollen lamellar structure. Upon the addition of salt at low to intermediate pH values, two lamellar phases, a collapsed and an expanded structure, coexist. Finally, when the polymer is fully ionized (at high pH), the extended conformation of the polymer generates a cubic phase. The results of this study contribute to an understanding of how polyelectrolytes may ultimately be harnessed for the preparation of self-assembling materials responsive to external stimuli.

  16. Strategy for identifying unknown hemoglobin adducts using adductome LC-MS/MS data: Identification of adducts corresponding to acrylic acid, glyoxal, methylglyoxal, and 1-octen-3-one.

    PubMed

    Carlsson, Henrik; Törnqvist, Margareta

    2016-06-01

    Electrophilic compounds have the ability to form adducts with nucleophilic sites in proteins and DNA in tissues, and thereby constitute risks for toxic effects. Adductomic approaches are developed for systematic screening of adducts to DNA and blood proteins, with the aim to detect unknown internal exposures to electrophiles. In a previous adductomic screening of adducts to N-terminals in hemoglobin, using LC-MS/MS, 19 unknown adducts were detected in addition to seven previously identified adducts. The present paper describes the identification of four of these unknown adducts, as well as the strategy used to identify them. Using LC-MS data from the screening, hypotheses about adduct identities were formulated: probable precursor electrophiles with matching molecular weights were suggested based on the molecular weights of the modifications and the retention times of the analytes, in combination with comparisons of theoretical Log P calculations and databases. Reference adducts were generated by incubation of blood samples with the hypothesized precursor electrophiles. The four identified precursor electrophiles, corresponding to the observed unknown adducts, were glyoxal, methylglyoxal, acrylic acid and 1-octen-3-one. Possible origins/exposure sources and toxicological information concerning the electrophilic precursors are discussed. The identified adducts could be explored as possible biomarkers for exposure. PMID:27046699

  17. Phase-transfer behavior of cross-linked poly(acrylic acid) particles prepared by dispersion polymerization from ionic liquid to water.

    PubMed

    Minami, Hideto; Mizuta, Yusuke; Kimura, Akira

    2012-02-01

    The phase-transfer behavior of poly(acrylic acid) (PAA) particles from the hydrophobic ionic liquid N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethanesulfonyl)amide phase to the water phase in the particle state, which we reported previously, was examined in more detail. PAA particles were prepared in the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide ([Bmim][TFSA]) and the organic solvent chloroform and were extracted. The transfer of PAA particles to water in the particle state was also observed in [Bmim][TFSA] systems. In contrast, the transfer phenomenon was not observed in the chloroform system. It was clarified that water/oil interfacial tension γ(wo) is an important parameter in the extraction of PAA in the particle state from the viewpoint of free energy. When the cationic surfactant tetradecyltrimethylammonium bromide, aqueous solution was used as the extraction medium, the PAA particles were extracted in the particle state from chloroform to water, in which γ(wo) became as low as that of the ionic liquid. This suggests that the phase-transfer phenomenon of PAA particles in the particle state was induced by the ionic liquid's unique property of low interfacial tension with water despite its high hydrophobic character. PMID:22235893

  18. Photocurable bioactive bone cement based on hydroxyethyl methacrylate-poly(acrylic/maleic) acid resin and mesoporous sol gel-derived bioactive glass.

    PubMed

    Hesaraki, S

    2016-06-01

    This paper reports on strong and bioactive bone cement based on ternary bioactive SiO2-CaO-P2O5 glass particles and a photocurable resin comprising hydroxyethyl methacrylate (HEMA) and poly(acrylic/maleic) acid. The as-cured composite represented a compressive strength of about 95 MPa but it weakened during soaking in simulated body fluid, SBF, qua its compressive strength reached to about 20 MPa after immersing for 30 days. Biodegradability of the composite was confirmed by reducing its initial weight (~32%) as well as decreasing the molecular weight of early cured resin during the soaking procedure. The composite exhibited in vitro calcium phosphate precipitation in the form of nanosized carbonated hydroxyapatite, which indicates its bone bonding ability. Proliferation of calvarium-derived newborn rat osteoblasts seeded on top of the composite was observed during incubation at 37 °C, meanwhile, an adequate cell supporting ability was found. Consequently, it seems that the produced composite is an appropriate alternative for bone defect injuries, because of its good cell responses, high compressive strength and ongoing biodegradability, though more in vivo experiments are essential to confirm this assumption. PMID:27040248

  19. Poly(acrylic acid) Bridged Gadolinium Metal-Organic Framework-Gold Nanoparticle Composites as Contrast Agents for Computed Tomography and Magnetic Resonance Bimodal Imaging

    PubMed Central

    Tian, Chixia; Zhu, Liping; Lin, Feng; Boyes, Stephen G.

    2015-01-01

    Imaging contrast agents for magnetic resonance imaging (MRI) and computed tomography (CT) have received significant attention in the development of techniques for early-stage cancer diagnosis. Gadolinium (Gd) (III), which has seven unpaired electrons and a large magnetic moment, can dramatically influence the water proton relaxation and hence exhibits excellent MRI contrast. On the other hand, gold (Au), which has a high atomic number and high x-ray attenuation coefficient, is an ideal contrast agent candidate for x-ray based CT imaging. Gd metal organic framework (MOF) nanoparticles with tunable size, high Gd (III) loading and multivalency can potentially overcome the limitations of clinically utilized Gd chelate contrast agents. In this work, we report for the first time the integration of GdMOF nanoparticles with gold nanoparticles (AuNPs) for the preparation of a MRI/CT bimodal imaging agent. Highly stable hybrid GdMOF/AuNPs composites have been prepared by using poly(acrylic acid) as a bridge between the GdMOF nanoparticles and AuNPs. The hybrid nanocomposites were then evaluated in MRI and CT imaging. The results revealed high longitudinal relaxivity in MRI and excellent CT imaging performance. Therefore, these GdMOF/AuNPs hybrid nanocomposites potentially provide a new platform for the development of multi-modal imaging probes. PMID:26147906

  20. Sono-assisted photocatalytic degradation of styrene-acrylic acid copolymer in aqueous media with nano titania particles and kinetic studies.

    PubMed

    Saien, J; Delavari, H; Solymani, A R

    2010-05-15

    The ultrasonic irradiation (28 kHz, 50 W) in pre-cavitations regime was employed to enhance the degradation rate of styrene-acrylic acid copolymer in aqueous media with nano titania photocatalyst particles. A stainless steel cylindrical sono-photo reactor with capacity of about 1.25 L, equipped with a UV lamp (250 W) was used. The influence of operational parameters, i.e. catalyst concentration, pH and temperature was studied and the role of active species was also distinguished. For an initial substrate concentration of 30 mg L(-1), under mild applied conditions of 30 mg L(-1) of photocatalyst, 25 degrees C and natural pH, a degradation and mineralization conversion of 96% and 91%, respectively, was achieved using sono-assisted photocatalysis process in about only 60 min. These efficiencies are much higher than those obtained with only photocatalysis process. Meanwhile, the threshold of cavitations was found corresponded to catalyst concentration of about 70 mg L(-1). Kinetic studies based on Langmuir-Hinshelwood and power law models in addition to the results from radical scavenger usage revealed that for sono-assisted process, the substrate undergoes degradation mainly via electron-hole redox on the surface of titania particles. It is while for the only photocatalysis process, the reaction proceeds via hydroxyl radicals in the solution bulk. PMID:20092940

  1. Metal ions doped chitosan-poly(acrylic acid) nanospheres: Synthesis and their application in simultaneously electrochemical detection of four markers of pancreatic cancer.

    PubMed

    Rong, Qinfeng; Feng, Feng; Ma, Zhanfang

    2016-01-15

    In this work, a one-pot method was designed to synthesize copper ions, cadmium ions, lead ions and zinc ions doped chitosan-poly(acrylic acid) nanospheres. Those nanospheres can not only produce independent electrochemical signals, but also react with glutaraldehyde (GA) to immobilize different labeled antibodies. Using the modified nanospheres as immunoprobes, a sandwich-type immunosensor was fabricated to simultaneous detection of four tumor markers (CEA, CA199, CA125 and CA242) of pancreatic cancer. This designed immunosensor exhibited good linear relationships in range from 0.1 to 100ng mL(-1) for CEA, 1 to 150UmL(-1) for CA199, CA125 and CA242, corresponding detection limits 0.02ng mL(-1), 0.4UmL(-1), 0.3UmL(-1) and 0.4UmL(-1), respectively. Meanwhile, the immunosensor was applied in analysis of clinical serum samples, whose results were well agreed with the enzyme-linked immunosorbent assay (ELISA), indicating that the proposed immunosensor gave a hope for the identification and validation of specific early cancer. PMID:26318783

  2. Poly(acrylic acid)-regulated Synthesis of Rod-Like Calcium Carbonate Nanoparticles for Inducing the Osteogenic Differentiation of MC3T3-E1 Cells

    PubMed Central

    Yang, Wei; Yao, Chenxue; Cui, Zhengyang; Luo, Dandan; Lee, In-Seop; Yao, Juming; Chen, Cen; Kong, Xiangdong

    2016-01-01

    Calcium carbonate, especially with nanostructure, has been considered as a good candidate material for bone regeneration due to its excellent biodegradability and osteoconductivity. In this study, rod-like calcium carbonate nanoparticles (Rod-CC NPs) with desired water dispersibility were achieved with the regulation of poly (acrylic acid). Characterization results revealed that the Rod-CC NPs had an average length of 240 nm, a width of 90 nm with an average aspect ratio of 2.60 and a negative ζ-potential of −22.25 ± 0.35 mV. The degradation study illustrated the nanoparticles degraded 23% at pH 7.4 and 45% at pH 5.6 in phosphate-buffered saline (PBS) solution within three months. When cultured with MC3T3-E1 cells, the Rod-CC NPs exhibited a positive effect on the proliferation of osteoblast cells. Alkaline phosphatase (ALP) activity assays together with the osteocalcin (OCN) and bone sialoprotein (BSP) expression observations demonstrated the nanoparticles could induce the differentiation of MC3T3-E1 cells. Our study developed well-dispersed rod-like calcium carbonate nanoparticles which have great potential to be used in bone regeneration. PMID:27164090

  3. Palladium Nanoparticles Embedded in a Layer-by-Layer Nanoreactor Built with Poly(Acrylic Acid) Using "Electro-Click Chemistry".

    PubMed

    Villalba, Matias; Bossi, Mariano; Pozo, Maria Del; Calvo, Ernesto J

    2016-07-12

    Palladium nanoparticles (Pd NPs) were formed by electrochemical reduction of Pd(NH3)4(3+) ions entrapped by ion exchange in poly(acrylic acid) (PAA) multilayer films grown by the Sharpless "click reaction." The alkyne (PAAalk) and azide (PAAaz) groups were covalently bound to the PAA, and the catalyzed buildup of the multilayer film was performed by electrochemical reduction of Cu(2+) to Cu(+). The size of the Pd NPs formed in Au/(PAAalk)3(PAAaz)2 multilayer films by the click reaction, that is, 50 nm, is larger than that of similar Pd NPs formed in electrostatically bound Au/(PAA)3(PAH)2 nanoreactors, that is, 6-9 nm, under similar conditions. A combination of electrochemical methods and electrochemical quartz crystal microbalance, polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS), ellipsometry, and scanning electron microscopy has been used to follow these processes. Cyclic voltammetry of the resulting Pd NPs in a 0.1 M H2SO4 solution at 0.1 V·s(-1) shows the PdO reduction peak at the same potential as that on the clean Pd surface unlike the NPs formed in electrostatically self-assembled Au/(PAA)3(PAH)2 nanoreactors with a 0.2 V shift in the cathodic direction most probably because of the strong adsorption of amino groups on the Pd NP surfaces. PMID:27308840

  4. Preparation and characterization of pH-sensitive and antifouling poly(vinylidene fluoride) microfiltration membranes blended with poly(methyl methacrylate-2-hydroxyethyl methacrylate-acrylic acid).

    PubMed

    Ju, Junping; Wang, Chao; Wang, Tingmei; Wang, Qihua

    2014-11-15

    Functional terpolymer of poly(methyl methacrylate-2-hydroxyethyl methacrylate-acrylic acid) (P(MMA-HEMA-AA)) was synthesized via a radical polymerization method. The terpolymer could be directly blended with poly(vinylidene fluoride) (PVDF) to prepare the microfiltration (MF) membranes via phase separate process. The synthesized polymers were characterized by Fourier transform infrared (FTIR), the nuclear magnetic resonance proton spectra ((1)H NMR). The membrane had the typical asymmetric structure and the hydrophilic side chains tended to aggregate on the membrane surface. The surface enrichment of amphiphilic copolymer and morphology of MF membranes were characterized by Fourier transform infrared attenuated total reflection spectroscopy (FTIR-ATR) and scanning electron microscopy (SEM). The contact angle (CA) and water uptake were also tested to assess the hydrophilicity and wetting characteristics of the polymer surface. The water filtration properties were measured. It was found the modified membranes showed excellent pH-sensitivity and pH-reversibility behavior. Furthermore, the hydrophilicity of the blended membranes increased, and the membranes showed good protein antifouling property. PMID:25203908

  5. Characterization of the oxide formed in the presence of poly acrylic acid over the steam generator structural materials of nuclear power plants

    NASA Astrophysics Data System (ADS)

    Joshi, Akhilesh C.; Rufus, Appadurai L.; Suresh, Sumathi; Chandramohan, Palogi; Rangarajan, Srinivasan; Velmurugan, Sankaralingam

    2013-06-01

    On-line addition of polymeric dispersants, such as poly acrylic acid (PAA), to the steam generator (SG) results in the formation of a better protective inner oxide layer that reduces subsequent corrosion of structural materials. Its dispersive action inhibits the growth of a secondary oxide layer thereby facilitating their easy removal. This paper discusses the effect of PAA on the nature of oxides formed over the surfaces of SG. In the case of carbon steel, the inner oxide layer (magnetite) formed in the presence of PAA was protective. Electrochemical studies showed a minimum concentration of 350 ppb of PAA was found to be optimum. On the monel surface, in the absence of PAA, nickel ferrite was formed while in the presence of PAA, the oxide formed was a mixture of oxides of copper and nickel. A concentration of 700 ppb of PAA was found to be optimum for monel. In the case of incoloy, the effect of PAA was not discernible except for the size and morphology of the crystallites formed.

  6. One-Pot Synthesis of Hydrophilic Superparamagnetic Fe3O4/Poly(methyl methacrylate-acrylic acid) Composite Nanoparticles with High Magnetization.

    PubMed

    Ma, Shaohua; Lan, Fang; Yang, Qi; Xie, Liqin; Wu, Yao; Gu, Zhongwei

    2015-01-01

    Uniform superparamagnetic Fe3O4/poly(methyl methacrylate-acrylic acid) (P(MMA-AA)) composite nanoparticles with high saturation magnetization and good hydrophilicity were successfully and directly synthesized via a facile one-pot miniemulsion polymerization approach. The mixture of the ferrofluids, MMA and AA monomers, surfactants and initiator was co-sonicated and emulsified to prepare stable miniemulsion for polymerization. The as-prepared products were characterized by SEM, TEM, FT-IR, XRD, TGA and VSM. The results of SEM indicated that the morphology of the Fe3O4/P(MMA-AA) composite nanoparticles all assumed near spherical geometry with diameters about 60 nm, 60 nm, and 100 nm respectively corresponding to the weight ratios of Fe3O4 to MMA and AA at 1:8, 1:4, and 1:2. The TEM images implied that the Fe3O4/P(MMA-AA) composite nanoparticles showed a perfect core-shell structure with a polymeric shell of about 2 nm thickness and a core encapsulating uniform and close packed Fe3O4 nanoparticles. TGA and VSM showed that the Fe3O4/P(MMA-AA) composite nanoparticles with a maximum saturation magnetization up to 45 emu g(-1) corresponding to the magnetite content of 78% exhibited superparamagntism. The hydrophilic modification and the high saturation magnetization impart a promising potential for biomedical applications to the as-synthesized composite nanoparticles. PMID:26328359

  7. Measurement of non-DLVO force on a silicon substrate coated with ammonium poly(acrylic acid) using scanning probe microscopy

    NASA Astrophysics Data System (ADS)

    Isobe, Toshihiro; Nakano, Yosuke; Kameshima, Yoshikazu; Nakajima, Akira; Okada, Kiyoshi

    2009-07-01

    The repulsive force originating from steric hindrance of polymers in aqueous solvent was investigated using scanning probe microscopy (SPM). The contact angle (CA) of ammonium poly(acrylic acid) (PAA) solution on the Si surface was measured to estimate the state of the Si substrate. Results of CA measurement show that the Si surface was fully covered with PAA at 0.1 mass% in aqueous solution. The interaction force between the Si tip and the wafer was estimated using the SPM force curve mode. The force curve measured in the ion-exchanged purified water showed the typical relation predicted by Derjaguin-Landau-Verway-Overbeek (DLVO) theory. However, the force curve shape in the 0.1 mass% PAA solution was significantly different. Only a repulsive force was observed at less than about 4 nm of separation distance between the Si wafer and cantilever tip. This distance originated from the steric repulsions of PAA adsorbed onto the Si wafer and cantilever tip.

  8. pH-responsive controlled-release fertilizer with water retention via atom transfer radical polymerization of acrylic acid on mussel-inspired initiator.

    PubMed

    Ma, Zhi-yuan; Jia, Xin; Zhang, Guo-xiang; Hu, Jia-mei; Zhang, Xiu-lan; Liu, Zhi-yong; Wang, He-yun; Zhou, Feng

    2013-06-12

    This work reports a polydopamine-graft-poly(acrylic acid) (Pdop-g-PAA)-coated controlled-release multi-element compound fertilizer with water-retention function by a combination of mussel-inspired chemistry and surface-initiated atom transfer radical polymerization (SI-ATRP) techniques for the first time. The morphology and composition of the products were characterized by transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), gel permeation chromatography (GPC), and inductively coupled plasma (ICP) emission spectrometry. The results revealed that the stimuli-responsive layer formed by a Pdop inner layer and a PAA outer corona exhibit outstanding selective permeability to charged nutrients and the release rate of encapsulated elements can be tailored by the pH values. At low pH, the Pdop-g-PAA layer can reduce nutrient loss, and at high pH, the coating restrains transportation of negative nutrients but favors the release of cations. Moreover, PAA brushes provide good water-retention property. This Pdop-graft-polymer brushes coating will be effective and promising in the research and development of multi-functional controlled-release fertilizer. PMID:23692274

  9. Preparation and dielectric analysis of microphase-separated poly(acrylonitrile-co-acrylamide-co-acrylic acid) hydrogels

    SciTech Connect

    Hu, D.Shiaw-Guang; Lin, Yow-Shi

    1993-12-31

    The acidic hydrolysis of polyacrylonitrile was carried out to yield a variety of terpolymers made up of nitriles, amides and acids. The formation of block structure was shown to follow a ripper mechanism occurring to acrylamide groups, that is more pronounced for a certain range of acrylamide content, evidenced by the composition analysis using {sup 1}H-NMR and base titration. The rates of formation of acrylamide fraction and acid fraction in the consecutive mode are approximately the same, yielding the content of ionic groups from 0.8 to 2.2. mole percent, dependent on the time of hydrolysis. The dielectric relaxation measurement on swollen gels shows three relaxation transitions, {alpha}, {beta}, {gamma}, over -150{degrees}C to 0{degrees}C, as influenced by the chemical composition and water absorption. The {beta} and {gamma} are associated with the polymer-water interaction and short-range motion of polymers and water.

  10. Silicone/Acrylate Copolymers

    NASA Technical Reports Server (NTRS)

    Dennis, W. E.

    1982-01-01

    Two-step process forms silicone/acrylate copolymers. Resulting acrylate functional fluid is reacted with other ingredients to produce copolymer. Films of polymer were formed by simply pouring or spraying mixture and allowing solvent to evaporate. Films showed good weatherability. Durable, clear polymer films protect photovoltaic cells.

  11. Information for AAC Users (Augmentative and Alternative Communication)

    MedlinePlus

    ... people in the United States have a severe communication disorder that impairs their ability to talk. This ... worsening throughout life). Common causes of severe expressive communication disorders that may require the use of AAC ...

  12. Properties and mechanisms of drug release from matrix tablets containing poly(ethylene oxide) and poly(acrylic acid) as release retardants.

    PubMed

    Zhang, Feng; Meng, Fan; Lubach, Joseph; Koleng, Joseph; Watson, N A

    2016-08-01

    The interactions between poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) in aqueous medium at pH 6.8 were investigated in the current study. We have also studied the effect of interpolymer interactions and various formulation variables, including the molecular weight of PEO, the ratio between PEO and PAA, the crystallinity of PEO, and the presence of an acidifying agent, on the release of theophylline from matrix tablets containing both PEO and PAA as release retardants. At pH 6.8, the synergy in solution viscosity between PEO and PAA as the result of ion-dipole interaction was observed in this study. The release of theophylline from the matrix tablets containing physical mixtures of PEO and PAA was found to be a function of dissolution medium pH because of the pH-dependent interactions between these two polymers. Because of the formation of water insoluble interpolymer complex between PEO and PAA in aqueous medium at pH below 4.0, the release of theophylline was independent of PEO molecular weight and was controlled by Fickian diffusion mechanism in 0.01N hydrochloric acid solution. In comparison, the drug release was a function of PEO molecular weight and followed the anomalous transport mechanism in phosphate buffer pH 6.8. The presence of PAA exerted opposite effects on the release of theophylline in phosphate buffer pH 6.8. In one aspect, theophylline release was accelerated because the erosion of PAA was much faster than that of PEO at pH6.8. On the opposite aspect, theophylline release was slowed down because of the formation of insoluble complex inside the gel layer as the result of the acidic microenvironment induced by PAA, and the increase in the viscosity of the gel layer as the result of the synergy between PEO and PAA. These two opposite effects offset each other. As a result, the release of theophylline remained statistically the same even when 75% PEO in the formulation was replaced with PAA. In phosphate buffer pH 6.8, the release of

  13. Optical limiting response of multi-walled carbon nanotube-phthalocyanine nanocomposite in solution and when in poly (acrylic acid)

    NASA Astrophysics Data System (ADS)

    Sekhosana, Kutloano Edward; Nyokong, Tebello

    2016-08-01

    Bis{23-(3,4-di-yloxybenzoic acid)-(2(3), 9(10), 16(17), 23(24)-(hexakis-pyridin-3-yloxy phthalocyaninato)} dineodymium (III) acetate (3) is linked to amino-functionalized multi-walled carbon nanotubes (MWCNT) to form 3-MWCNT. Z-scan technique was employed to experimentally determine the nonlinear absorption coefficient from the open-aperture data. The limiting threshold values as low as 0.045 J cm-2 were found in solution. The conjugate (3-MWCNT) gave better optical limiting behavior than complex 3 alone.

  14. Formation of High-Capacity Protein-Adsorbing Membranes Through Simple Adsorption of Poly(acrylic acid)-Containing Films at low pH

    PubMed Central

    Bhattacharjee, Somnath; Dong, Jinlan; Ma, Yiding; Hovde, Stacy; Geiger, James H; Baker, Gregory L.; Bruening, Merlin L.

    2012-01-01

    Layer-by-layer polyelectrolyte adsorption is a simple, convenient method for introducing ion-exchange sites in porous membranes. This study demonstrates that adsorption of poly(acrylic acid) (PAA)-containing films at pH 3 rather than pH 5 increases the protein-binding capacity of such polyelectrolyte-modified membranes 3- to 6-fold. The low adsorption pH generates a high density of –COOH groups that function as either ion-exchange sites or points for covalent immobilization of metal-ion complexes that selectively bind tagged proteins. When functionalized with nitrilotriacetate (NTA)-Ni2+ complexes, membranes containing PAA/polyethyleneimine (PEI)/PAA films bind 93 mg of histidine6-tagged (His-tagged) ubiquitin per cm3 of membrane. Additionally these membranes isolate His-tagged COP9 signalosome complex subunit 8 from cell extracts and show >90% recovery of His-tagged ubiquitin. Although modification with polyelectrolyte films occurs by simply passing polyelectrolyte solutions through the membrane for as little as 5 min, with low-pH deposition the protein binding capacities of such membranes are as high as for membranes modified with polymer brushes and 2–3 fold higher than for commercially available IMAC resins. Moreover, the buffer permeabilities of polyelectrolyte-modified membranes that bind His-tagged protein are ~30% of the corresponding permeabilities of unmodified membranes, so protein capture can occur rapidly with low pressure drops. Even at a solution linear velocity of 570 cm/h, membranes modified with PAA/PEI/PAA exhibit a lysozyme dynamic binding capacity (capacity at 10% breakthrough) of ~ 40 mg/cm3. Preliminary studies suggest that these membranes are stable under depyrogenation conditions (1 M NaOH). PMID:22468687

  15. Heterogeneously catalysed partial oxidation of acrolein to acrylic acid--structure, function and dynamics of the V-Mo-W mixed oxides.

    PubMed

    Kampe, Philip; Giebeler, Lars; Samuelis, Dominik; Kunert, Jan; Drochner, Alfons; Haass, Frank; Adams, Andreas H; Ott, Joerg; Endres, Silvia; Schimanke, Guido; Buhrmester, Thorsten; Martin, Manfred; Fuess, Hartmut; Vogel, Herbert

    2007-07-21

    The major objective of this research project was to reach a microscopic understanding of the structure, function and dynamics of V-Mo-(W) mixed oxides for the partial oxidation of acrolein to acrylic acid. Different model catalysts (from binary and ternary vanadium molybdenum oxides up to quaternary oxides with additional tungsten) were prepared via a solid state preparation route and hydrochemical preparation of precursors by spray-drying or crystallisation with subsequent calcination. The phase composition was investigated ex situ by XRD and HR-TEM. Solid state prepared samples are characterised by crystalline phases associated to suitable phase diagrams. Samples prepared from crystallised and spray-dried precursors show crystalline phases which are not part of the phase diagram. Amorphous or nanocrystalline structures are only found in tungsten doped samples. The kinetics of the partial oxidation as well as the catalysts' structure have been studied in situ by XAS, XRD, temperature programmed reaction and reduction as well as by a transient isotopic tracing technique (SSITKA). The reduction and re-oxidation kinetics of the bulk phase have been evaluated by XAS. A direct influence not only of the catalysts' composition but also of the preparation route is shown. Altogether correlations are drawn between structure, oxygen dynamics and the catalytic performance in terms of activity, selectivity and long-term stability. A model for the solid state behaviour under reaction conditions has been developed. Furthermore, isotope exchange experiments provided a closer image of the mechanism of the selective acrolein oxidation. Based on the in situ characterisation in combination with micro kinetic modelling a detailed reaction model which describes the oxygen exchange and the processes at the catalyst more precisely is discussed. PMID:17612723

  16. Improved In Vitro and In Vivo Biocompatibility of Graphene Oxide through Surface Modification: Poly(Acrylic Acid)-Functionalization is Superior to PEGylation.

    PubMed

    Xu, Ming; Zhu, Jianqiang; Wang, Fanfan; Xiong, Yunjing; Wu, Yakun; Wang, Qiuquan; Weng, Jian; Zhang, Zhihong; Chen, Wei; Liu, Sijin

    2016-03-22

    The unique physicochemical properties of two-dimensional (2D) graphene oxide (GO) could greatly benefit the biomedical field; however, recent research demonstrated that GO could induce in vitro and in vivo toxicity. We determined the mechanism of GO induced toxicity, and our in vitro experiments revealed that pristine GO could impair cell membrane integrity and functions including regulation of membrane- and cytoskeleton-associated genes, membrane permeability, fluidity and ion channels. Furthermore, GO induced platelet depletion, pro-inflammatory response and pathological changes of lung and liver in mice. To improve the biocompatibility of pristine GO, we prepared a series of GO derivatives including aminated GO (GO-NH2), poly(acrylamide)-functionalized GO (GO-PAM), poly(acrylic acid)-functionalized GO (GO-PAA) and poly(ethylene glycol)-functionalized GO (GO-PEG), and compared their toxicity with pristine GO in vitro and in vivo. Among these GO derivatives, GO-PEG and GO-PAA induced less toxicity than pristine GO, and GO-PAA was the most biocompatible one in vitro and in vivo. The differences in biocompatibility were due to the differential compositions of protein corona, especially immunoglobulin G (IgG), formed on their surfaces that determine their cell membrane interaction and cellular uptake, the extent of platelet depletion in blood, thrombus formation under short-term exposure and the pro-inflammatory effects under long-term exposure. Overall, our combined data delineated the key molecular mechanisms underlying the in vivo and in vitro biological behaviors and toxicity of pristine GO, and identified a safer GO derivative that could be used for future applications. PMID:26855010

  17. Electrospun Poly(acrylic acid)/Silica Hydrogel Nanofibers Scaffold for Highly Efficient Adsorption of Lanthanide Ions and Its Photoluminescence Performance.

    PubMed

    Wang, Min; Li, Xiong; Hua, Weikang; Shen, Lingdi; Yu, Xufeng; Wang, Xuefen

    2016-09-14

    Combined with the features of electrospun nanofibers and the nature of hydrogel, a novel choreographed poly(acrylic acid)-silica hydrogel nanofibers (PAA-S HNFs) scaffold with excellent rare earth elements (REEs) recovery performance was fabricated by a facile route consisting of colloid-electrospinning of PAA/SiO2 precursor solution, moderate thermal cross-linking of PAA-S nanofiber matrix, and full swelling in water. The resultant PAA-S HNFs with a loose and spongy porous network structure exhibited a remarkable adsorption capacity of lanthanide ions (Ln(3+)) triggered by the penetration of Ln(3+) from the nanofiber surface to interior through the abundant water channels, which took full advantage of the internal adsorption sites of nanofibers. The effects of initial solution pH, concentration, and contact time on adsorption of Ln(3+) have been investigated comprehensively. The maximum equilibrium adsorption capacities for La(3+), Eu(3+), and Tb(3+) were 232.6, 268.8, and 250.0 mg/g, respectively, at pH 6, and the adsorption data were well-fitted to the Langmuir isotherm and pseudo-second-order models. The resultant PAA-S HNFs scaffolds could be regenerated successfully. Furthermore, the proposed adsorption mechanism of Ln(3+) on PAA-S HNFs scaffolds was the formation of bidentate carboxylates between carboxyl groups and Ln(3+) confirmed by FT-IR and XPS analysis. The well-designed PAA-S HNFs scaffold can be used as a promising alternative for effective REEs recovery. Moreover, benefiting from the unique features of Ln(3+), the Ln-PAA-S HNFs simultaneously exhibited versatile advantages including good photoluminescent performance, tunable emission color, and excellent flexibility and processability, which also hold great potential for applications in luminescent patterning, underwater fluorescent devices, sensors, and biomaterials, among others. PMID:27537710

  18. Radiation-induced synthesis and swelling properties of p(2-hydroxyethyl methacrylate/itaconic acid/oligo (ethylene glycol) acrylate) terpolymeric hydrogels

    NASA Astrophysics Data System (ADS)

    Micic, M.; Stamenic, D.; Suljovrujic, E.

    2012-09-01

    Since it is presumed that by incorporation of pH-responsive (IA) and temperature-responsive (OEGA) co-monomers, it is possible to prepare P(HEMA/IA/OEGA) hydrogels with dual (pH and thermo) responsiveness, the main purpose of our study is to investigate the influence of different mole fractions of IA and especially OEGA on the diversity of the swelling properties of the obtained hydrogels. For that reason, a series of terpolymeric hydrogels with different mole ratios of 2-hydroxyethyl methacrylate (HEMA), itaconic acid (IA) and oligo(ethylene glycol) acrylates (OEGA) was synthesised by gamma radiation. The obtained hydrogels were characterised by swelling studies in the wide pH (2.2-9.0) and temperature range (20-70 °C), confirming dual (pH and thermo) responsiveness and a large variation in the swelling capability. It was observed that the equilibrium swelling of P(HEMA/IA/OEGA) hydrogels, for a constant amount of IA, increased progressively with an increase in OEGA share. On the other hand, the dissociation of carboxyl groups from IA occurs at pH>4; therefore, small mole fractions of IA render good pH sensitivity and a large increase in the swelling capacity of these hydrogels at higher pH values. Additional characterisation of structure and properties was conducted by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and mechanical measurements, confirming that the inherent properties of P(HEMA/IA/OEGA) hydrogels can be significantly tuned by variation in their composition. According to all presented, it seems that the obtained hydrogels can be a beneficial synergetic combination for controlled delivery of bioactive molecules such as drugs, peptides, proteins, etc.

  19. Unusually Stable Hysteresis in the pH-Response of Poly(Acrylic Acid) Brushes Confined within Nanoporous Block Polymer Thin Films.

    PubMed

    Weidman, Jacob L; Mulvenna, Ryan A; Boudouris, Bryan W; Phillip, William A

    2016-06-01

    Stimuli-responsive soft materials are a highly studied field due to their wide-ranging applications; however, only a small group of these materials display hysteretic responses to stimuli. Moreover, previous reports of this behavior have typically shown it to be short-lived. In this work, poly(acrylic acid) (PAA) chains at extremely high grafting densities and confined in nanoscale pores displayed a unique long-lived hysteretic behavior caused by their ability to form a metastable hydrogen bond network. Hydraulic permeability measurements demonstrated that the conformation of the PAA chains exhibited a hysteretic dependence on pH, where different effective pore diameters arose in a pH range of 3 to 8, as determined by the pH of the previous environment. Further studies using Fourier transform infrared (FTIR) spectroscopy demonstrated that the fraction of ionized PAA moieties depended on the thin film history; this was corroborated by metal adsorption capacity, which demonstrated the same pH dependence. This hysteresis was shown to be persistent, enduring for days, in a manner unlike most other systems. The hypothesis that hydrogen bonding among PAA units contributed to the hysteretic behavior was supported by experiments with a urea solution, which disrupted the metastable hydrogen bonded state of PAA toward its ionized state. The ability of PAA to hydrogen bond within these confined pores results in a stable and tunable hysteresis not previously observed in homopolymer materials. An enhanced understanding of the polymer chemistry and physics governing this hysteresis gives insight into the design and manipulation of next-generation sensors and gating materials in nanoscale applications. PMID:27172428

  20. Poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol)/poly(acrylic acid) interpenetrating polymer networks for improving optrode-neural tissue interface in optogenetics.

    PubMed

    Lu, Yi; Li, Yanling; Pan, Jianqing; Wei, Pengfei; Liu, Nan; Wu, Bifeng; Cheng, Jinbo; Lu, Caiyi; Wang, Liping

    2012-01-01

    The field of optogenetics has been successfully used to understand the mechanisms of neuropsychiatric diseases through the precise spatial and temporal control of specific groups of neurons in a neural circuitry. However, it remains a great challenge to integrate optogenetic modulation with electrophysiological and behavioral read out methods as a means to explore the causal, temporally precise, and behaviorally relevant interactions of neurons in the specific circuits of freely behaving animals. In this study, an eight-channel chronically implantable optrode array was fabricated and modified with poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol)/poly(acrylic acid) interpenetrating polymer networks (PEDOT/PSS-PVA/PAA IPNs) for improving the optrode-neural tissue interface. The conducting polymer-hydrogel IPN films exhibited a significantly higher capacitance and lower electrochemical impedance at 1 kHz as compared to unmodified optrode sites and showed significantly improved mechanical and electrochemical stability as compared to pure conducting polymer films. The cell attachment and neurite outgrowth of rat pheochromocytoma (PC12) cells on the IPN films were clearly observed through calcein-AM staining. Furthermore, the optrode arrays were chronically implanted into the hippocampus of SD rats after the lentiviral expression of synapsin-ChR2-EYFP, and light-evoked, frequency-dependant action potentials were obtained in freely moving animals. The electrical recording results suggested that the modified optrode arrays showed significantly reduced impedance and RMS noise and an improved SNR as compared to unmodified sites, which may have benefited from the improved electrochemical performance and biocompatibility of the deposited IPN films. All these characteristics are greatly desired in optogenetic applications, and the fabrication method of conducting polymer-hydrogel IPNs can be easily integrated with other modification methods to build a

  1. Physicochemical properties of pH-controlled polyion complex (PIC) micelles of poly(acrylic acid)-based double hydrophilic block copolymers and various polyamines.

    PubMed

    Warnant, J; Marcotte, N; Reboul, J; Layrac, G; Aqil, A; Jerôme, C; Lerner, D A; Gérardin, C

    2012-05-01

    The physicochemical properties of polyion complex (PIC) micelles were investigated in order to characterize the cores constituted of electrostatic complexes of two oppositely charged polyelectrolytes. The pH-sensitive micelles were obtained with double hydrophilic block copolymers containing a poly(acrylic acid) block linked to a modified poly(ethylene oxide) block and various polyamines (polylysine, linear and branched polyethyleneimine, polyvinylpyridine, and polyallylamine). The pH range of micellization in which both components are ionized was determined for each polyamine. The resulting PIC micelles were characterized using dynamic light scattering and small-angle X-ray scattering experiments (SAXS). The PIC micelles presented a core-corona nanostructure with variable polymer density contrasts between the core and the corona, as revealed by the analysis of the SAXS curves. It was shown that PIC micelle cores constituted by polyacrylate chains and polyamines were more or less dense depending on the nature of the polyamine. It was also determined that the density of the cores of the PIC micelles depended strongly on the nature of the polyamine. These homogeneous cores were surrounded by a large hairy corona of hydrated polyethylene oxide block chains. Auramine O (AO) was successfully entrapped in the PIC micelles, and its fluorescence properties were used to get more insight on the core properties. Fluorescence data confirmed that the cores of such micelles are quite compact and that their microviscosity depended on the nature of the polyamine. The results obtained on these core-shell micelles allow contemplating a wide range of applications in which the AO probe would be replaced by various cationic drugs or other similarly charged species to form drug nanocarriers or new functional nanodevices. PMID:22453608

  2. Rapid removal of copper with magnetic poly-acrylic weak acid resin: quantitative role of bead radius on ion exchange.

    PubMed

    Fu, Lichun; Shuang, Chendong; Liu, Fuqiang; Li, Aimin; Li, Yan; Zhou, Yang; Song, Haiou

    2014-05-15

    A novel magnetic weak acid resin NDMC was self-synthesized for the removal of Cu(2+) from aqueous solutions. NDMC showed superior properties on the removal of Cu(2+) compared to commercial resins C106 and IRC-748, which was deeply investigated by adsorption isotherms and kinetic tests. The equilibrium adsorption amount of Cu(2+) onto NDMC (267.2mg/g) was almost twice as large as that onto IRC-748 (120.0mg/g). The adsorption kinetics of Cu(2+) onto the three resins fitted well with the pseudo-second-order equation. The initial adsorption rate h of NDMC was about 4 times that of C106 and nearly 8 times that of IRC-748 at the initial concentration of 500mg/L. External surface area was determined to be the key factor in rate-controlling by further analyzing the adsorption thermodynamics, kinetics parameters and physicochemical properties of the resins. NDMC resin with the smallest bead radius possessed the largest external surface and therefore exhibited the fastest kinetics. The adsorption amount of Cu(2+) onto NDMC was not influenced as the concentration of Na(+) increased from 1.0 to 10.0mM/L. Dilute HCl solution could effectively desorb Cu(2+). NDMC demonstrated high stability during 10 adsorption/desorption cycles, showing great potential in the rapid removal of Cu(2+) from wastewater. PMID:24681592

  3. Surface functionalisation of polypropylene hernia-repair meshes by RF-activated plasma polymerisation of acrylic acid and silver nanoparticles

    NASA Astrophysics Data System (ADS)

    Nisticò, Roberto; Rosellini, Andrea; Rivolo, Paola; Faga, Maria Giulia; Lamberti, Roberta; Martorana, Selanna; Castellino, Micaela; Virga, Alessandro; Mandracci, Pietro; Malandrino, Mery; Magnacca, Giuliana

    2015-02-01

    Hernia diseases are among the most common and diffuse causes of surgical interventions. Unfortunately, still nowadays there are different phenomena which can cause the hernioplasty failure, for instance post-operative prostheses displacements and proliferation of bacteria in the surgical site. In order to limit these problems, commercial polypropylene (PP) and polypropylene/Teflon (PP/PTFE) bi-material meshes were surface functionalised to confer adhesive properties (and therefore reduce undesired displacements) using polyacrylic acid synthesized by plasma polymerisation (PPAA). A broad physico-chemical and morphological characterisation was carried out and adhesion properties were investigated by means of atomic force microscopy (AFM) used in force/distance (F/D) mode. Once biomedical devices surface was functionalised by PPAA coating, metallic silver nanoparticles (AgNPs) with antimicrobial properties were synthesised and loaded onto the polymeric prostheses. The effect of the PPAA, containing carboxylic functionalities, adhesive coating towards AgNPs loading capacity was verified by means of X-ray photoelectron spectroscopy (XPS). Preliminary measurement of the Ag loaded amount and release in water were also investigated via inductively coupled plasma atomic emission spectroscopy (ICP-AES). Promising results were obtained for the functionalised biomaterials, encouraging future in vitro and in vivo tests.

  4. Analytical investigations of poly(acrylic acid) coatings electrodeposited on titanium-based implants: a versatile approach to biocompatibility enhancement.

    PubMed

    De Giglio, E; Cometa, S; Cioffi, N; Torsi, L; Sabbatini, L

    2007-12-01

    A polyacrylic acid film was synthesized on titanium substrates from aqueous solutions via an electroreductive process for the first time. This work was done in order to develop a versatile coating for titanium-based orthopaedic implants that acts as both an effective bioactive surface and an effective anti-corrosion barrier. The chemical structure of the PAA coating was investigated by X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was employed to evaluate the effect of annealing treatment on the morphology of the coatings in terms of their uniformity and porosity. Inductively coupled plasma mass spectrometry was used to measure ion concentrations in ion release tests performed on Ti-6Al-4V sheets modified with PAA coatings (annealed and unannealed). Results indicate that the annealing process produces coatings that possess considerable anti-corrosion performance. Moreover, the availability and the reactivity of the surface carboxylic groups were exploited in order to graft biological molecules onto the PAA-modified titanium implants. The feasibility of the grafting reaction was tested using a single aminoacid residue. A fluorinated aminoacid was selected, and the grafting reaction was monitored both by XPS, using fluorine as a marker element, and via quartz crystal microbalance (QCM) measurements. The success of the grafting reaction opens the door to the synthesis of a wide variety of PAA-based coatings that are functionalized with selected bioactive molecules and promote positive reactions with the biological system interfacing the implant while considerably reducing ion release into surrounding tissues. PMID:17516054

  5. Antistatic coating for acrylics

    NASA Technical Reports Server (NTRS)

    Hadek, V.; Rembaum, A.; Somono, R. B.

    1979-01-01

    After immersion in low molecular-weight solvents such as acetonitril or nitromethane, clear acrylic plastics dissipate up to 70% of induced electric charge within one minute, yet retain optical clarity.

  6. Matrix tablets based on thiolated poly(acrylic acid): pH-dependent variation in disintegration and mucoadhesion.

    PubMed

    Guggi, Davide; Marschütz, Michaela K; Bernkop-Schnürch, Andreas

    2004-04-15

    This study examined the influence of the pH on the mucoadhesive and cohesive properties of polyarcylic acid (PAA) and thiolated PAA. The pH of PAA (molecular mass: 450 kDa) and of a corresponding PAA-cysteine conjugate was adjusted to 3, 4, 5, 6, 7 and 8. The amount of immobilised thiol groups and disulfide bonds was determined via Ellman's reagent. Tablets were compressed out of each pH-batch of both thiolated and unmodified PAA and the swelling behaviour, the disintegration time and the mucoadhesiveness were evaluated. The amount of thiol/disulfide groups per gram thiolated PAA of pH 3 and pH 8 was determined to be 332 +/- 94 micromol and 162 +/- 46 micromol, respectively. The thiolated PAA tablets displayed a minimum four-fold higher water uptake compared to unmodified PAA tablets. A faster and higher water uptake of both polymer types was observed above pH 5. Thiolated polymer tablets showed a 3-20-fold more prolonged disintegration time than unmodified PAA tablets. The cohesiveness of PAA-cysteine conjugate increased at higher pH, whereas the unmodified PAA behaved inversely. A 3-7-fold stronger mucoadhesiveness was observed for the PAA-cysteine conjugate tablets compared to unmodified PAA tablets. For both thiolated and unmodified polymer the mucoadhesiveness was 2-4-fold enhanced below pH 5. The difference in mucoadhesion between the two polymer types was most pronounced at these lower pH values. In this study substantial information regarding the pH-dependence of mucoadhesion and cohesion of unmodified polyacrylates and of thiolated polyacrylates is provided, representing helpful basic information for an ameliorated deployment of these polymers. PMID:15072786

  7. The acrylic jacket crown.

    PubMed

    Bell, A M

    1975-04-01

    An attempt has been made to cover briefly the many applications of the acrylic jacket crown. It is readily understandable that this type of restoration has many shortcomings but at the same time it has many useful and important applications in dentistry when properly employed. It is hoped that the specialist and generalist alike will have found some new and useful applications of the acrylic jacket crown. PMID:1090464

  8. Acrylate Systemic Contact Dermatitis.

    PubMed

    Sauder, Maxwell B; Pratt, Melanie D

    2015-01-01

    Acrylates, the 2012 American Contact Dermatitis Society allergen of the year, are found in a range of products including the absorbent materials within feminine hygiene pads. When fully polymerized, acrylates are nonimmunogenic; however, if not completely cured, the monomers can be potent allergens.A 28-year-old woman is presented, who had her teeth varnished with Isodan (Septodont, Saint-Maur-des-Fossés, France) containing HEMA (2-hydroxyethyl methacrylate) with no initial reaction. Approximately 1 month later, the patient developed a genital dermatitis secondary to her feminine hygiene pads. The initial reaction resolved, but 5 months later, the patient developed a systemic contact dermatitis after receiving a second varnishing.The patient was dramatically patch test positive to many acrylates. This case demonstrates a reaction to likely unpolymerized acrylates within a feminine hygiene pad, as well as broad cross-reactivity or cosensitivity to acrylates, and possibly a systemic contact dermatitis with systemic re-exposure to unpolymerized acrylates. PMID:26367207

  9. Preparation and characterization of hybrid pH-sensitive hydrogels of chitosan-co-acrylic acid for controlled release of verapamil.

    PubMed

    Ranjha, Nazar M; Ayub, Gohar; Naseem, Shahzad; Ansari, Muhammad Tayyab

    2010-10-01

    In the present work crosslinked hydrogels based on chitosan (CS) and acrylic acid (AA) were prepared by free radical polymerization with various feed compositions using N,N methylenebisacrylamide (MBA) as crosslinking agent. Benzoyl peroxide was used as catalyst. Fourier transform infrared spectra (FTIR) confirmed the formation of the crosslinked hydrogels. This hydrogel is formed due to electrostatic interaction between cationic groups in CS and anionic groups in AA. Prepared hydrogels were used for dynamic and equilibrium swelling studies. For swelling behavior, effect of pH, polymeric and monomeric compositions and degree of crosslinking were investigated. Swelling studies were performed in USP phosphate buffer solutions of varying pH 1.2, 5.5, 6.5 and 7.5. Results showed that swelling increased by increasing AA contents in structure of hydrogels in solutions of higher pH values. This is due to the presence of more carboxylic groups available for ionization. On the other hand by increasing the chitosan content swelling increased in a solution of acidic pH, but this swelling was not significant and it is due to ionization of amine groups present in the structure of hydrogel. Swelling decreased with increase in crosslinking ratio owing to tighter hydrogel structure. Porosity and sol-gel fraction were also measured. With increase in CS and AA contents porosity and gel fraction increased, whereas by increasing MBA content porosity decreased and gel fraction increased. Furthermore, diffusion coefficient (D) and the network parameters i.e., the average molecular weight between crosslinks (M(c)), polymer volume fraction in swollen state (V(2s)), number of repeating units between crosslinks (M(r)) and crosslinking density (q) were calculated using Flory-Rehner theory. Selected samples were loaded with a model drug verapamil. Release of verapamil depends on the ratios of CS/AA, degree of crosslinking and pH of the medium. The release mechanisms were studied by fitting

  10. Multifunctional electroactive electrospun nanofiber structures from water solution blends of PVA/ODA–MMT and poly(maleic acid-alt-acrylic acid): effects of Ag, organoclay, structural rearrangement and NaOH doping factors

    NASA Astrophysics Data System (ADS)

    Şimşek, Murat; Rzayev, Zakir M. O.; Bunyatova, Ulviya

    2016-06-01

    Novel multifunctional colloidal polymer nanofiber electrolytes were fabricated by green reactive electrospinning nanotechnology from various water solution/dispersed blends of poly (vinyl alcohol-co-vinyl acetate) (PVA)/octadecyl amine-montmorillonite (ODA–MMT) as matrix polymer nanocomposite and poly(maleic acid-alt-acrylic acid) (poly(MAc-alt-AA) and/or its Ag-carrying complex as partner copolymers. Polymer nanofiber electrolytes were characterized using FTIR, XRD, thermal (DSC, TGA–DTG), SEM, and electrical analysis methods. Effects of partner copolymers, organoclay, in situ generated silver nanoparticles (AgNPs), and annealing procedure on physical and chemical properties of polymer composite nanofibers were investigated. The electrical properties (resistance, conductivity, activation energy) of nanofibers with/without NaOH doping agent were also evaluated. This work presented a structural rearrangement of nanofiber mats by annealing via decarboxylation of anhydride units with the formation of new conjugated double bond sites onto partner copolymer main chains. It was also found that the semiconductor behaviors of nanofiber structures were essentially improved with increasing temperature and fraction of partner copolymers as well as presence of organoclay and AgNPs in nanofiber composite.

  11. Acrylic vessel cleaning tests

    SciTech Connect

    Earle, D.; Hahn, R.L.; Boger, J.; Bonvin, E.

    1997-02-26

    The acrylic vessel as constructed is dirty. The dirt includes blue tape, Al tape, grease pencil, gemak, the glue or residue form these tapes, finger prints and dust of an unknown composition but probably mostly acrylic dust. This dirt has to be removed and once removed, the vessel has to be kept clean or at least to be easily cleanable at some future stage when access becomes much more difficult. The authors report on the results of a series of tests designed: (a) to prepare typical dirty samples of acrylic; (b) to remove dirt stuck to the acrylic surface; and (c) to measure the optical quality and Th concentration after cleaning. Specifications of the vessel call for very low levels of Th which could come from tape residues, the grease pencil, or other sources of dirt. This report does not address the concerns of how to keep the vessel clean after an initial cleaning and during the removal of the scaffolding. Alconox is recommended as the cleaner of choice. This acrylic vessel will be used in the Sudbury Neutrino Observatory.

  12. THE 13TH ADVANCED ACCELERATOR CONCEPTS WORKSHOP (AAC'8)

    SciTech Connect

    Leemans, Wim; Schroder, Carl B.; Esarey, Eric

    2008-07-15

    The Thirteenth Workshop on Advanced Accelerator Concepts (AAC) was held from July 27 to August 2, 2008 at the Chaminade Conference Center in Santa Cruz, California, USA, organized by the Lawrence Berkeley National Laboratory and the University of California at Berkeley. There were unprecedented levels of interest in the 2008 AAC Workshop, and participation was by invitation, with 215 workshop attendees, including 58 students. Reflecting the world-wide growth of the advanced accelerator community, there was significant international participation, with participants from twelve countries attending.

  13. The effect of aided AAC modeling on the expression of multi-symbol messages by preschoolers who use AAC.

    PubMed

    Binger, Cathy; Light, Janice

    2007-03-01

    A single subject, multiple probe design across participants was used to evaluate the impact of using aided AAC modeling to support multi-symbol message production. Five preschoolers (three who used voice output communication systems, two who used non-electronic communication boards) participated in the study. Aided AAC models were provided by pointing to two symbols on the child's aided AAC system and then providing a grammatically complete spoken model while engaging in play activities. Four of the five preschoolers learned to consistently produce multi-symbol messages; the fifth did not demonstrate consistent gains. The four preschoolers who met criterion all evidenced long-term use of symbol combinations and generalized use of symbol combinations to novel play routines. Results, clinical implications, and future research directions are discussed. PMID:17364486

  14. Acrylic purification and coatings

    SciTech Connect

    Kuzniak, Marcin

    2011-04-27

    Radon (Rn) and its decay daughters are a well-known source of background in direct WIMP detection experiments, as either a Rn decay daughter or an alpha particle emitted from a thin inner surface layer of a detector could produce a WIMP-like signal. Different surface treatment and cleaning techniques have been employed in the past to remove this type of contamination. A new method of dealing with the problem has been proposed and used for a prototype acrylic DEAP-1 detector. Inner surfaces of the detector were coated with a layer of ultra pure acrylic, meant to shield the active volume from alphas and recoiling nuclei. An acrylic purification technique and two coating techniques are described: a solvent-borne (tested on DEAP-1) and solvent-less (being developed for the full scale DEAP-3600 detector).

  15. Improved homopolymer separation to enable the application of 1H NMR and HPLC for the determination of the reaction parameters of the graft copolymerization of acrylic acid onto starch.

    PubMed

    Witono, Judy R; Marsman, Jan Henk; Noordergraaf, Inge-Willem; Heeres, Hero J; Janssen, Leon P B M

    2013-04-01

    Graft copolymers of starch with acrylic acid are a promising green, bio based material with many potential applications. The grafting of acrylic acid onto cassava starch in an aqueous medium initiated by Fenton's reagent has been studied. Common grafting result parameters are add-on (yield) and graft efficiency (selectivity). However, the analysis of the reaction products and an accurate determination of these parameters stand or fall with a complete separation of the entangled but ungrafted homopolymer from the grafted product. Therefore, this separation is the core of the newly developed analytical procedure. An appropriate solvent has been selected with dedicated testing from the range methanol, ethanol, acetone, dioxane, 2-propanol, and 1-propanol. Acetone showed the best performance in many respects. It has a high dissolving power for the homopolymer, as well as the highest yield of precipitation for the starch derivatives and it is the most economical in use. After the successful separation, the precipitated graft copolymers could be analyzed quantitatively by nuclear magnetic resonance. The liquid with homopolymer and unreacted monomer was analyzed by high pressure liquid chromatography. Proof of grafting has been found by FTIR and TGA analyses. The mass balance calculation shows a systematic error which appears fairly consistent: 18.0±2.5 wt%. This was used as a correction factor in the calculation of the grafting parameters but more importantly, it means that the method we developed has a high level of repeatability, in the order of 97%. PMID:23435285

  16. Synthesis of linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite as an adsorbent for removal of Pb(ΙΙ) from aqueous solutions.

    PubMed

    Irani, Maryam; Ismail, Hanafi; Ahmad, Zulkifli; Fan, Maohong

    2015-01-01

    The purpose of this work is to remove Pb(II) from the aqueous solution using a type of hydrogel composite. A hydrogel composite consisting of waste linear low density polyethylene, acrylic acid, starch, and organo-montmorillonite was prepared through emulsion polymerization method. Fourier transform infrared spectroscopy (FTIR), Solid carbon nuclear magnetic resonance spectroscopy (CNMR)), silicon(-29) nuclear magnetic resonance spectroscopy (Si NMR)), and X-ray diffraction spectroscope ((XRD) were applied to characterize the hydrogel composite. The hydrogel composite was then employed as an adsorbent for the removal of Pb(II) from the aqueous solution. The Pb(II)-loaded hydrogel composite was characterized using Fourier transform infrared spectroscopy (FTIR)), scanning electron microscopy (SEM)), and X-ray photoelectron spectroscopy ((XPS)). From XPS results, it was found that the carboxyl and hydroxyl groups of the hydrogel composite participated in the removal of Pb(II). Kinetic studies indicated that the adsorption of Pb(II) followed the pseudo-second-order equation. It was also found that the Langmuir model described the adsorption isotherm better than the Freundlich isotherm. The maximum removal capacity of the hydrogel composite for Pb(II) ions was 430mg/g. Thus, the waste linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite could be a promising Pb(II) adsorbent. PMID:25597658

  17. Structure-toxicity relationships of acrylic monomers.

    PubMed Central

    Autian, J

    1975-01-01

    Esters of acrylic acid, in particular methyl methacrylate, have wide applications in a number of industrial and consumer products, forming very desirable nonbreakable glass-like materials. In dentistry, the monomers are used to prepare dentures and a variety of filling and coating materials for the teeth. Surgeons utilize the monomers to prepare a cement which helps anchor prosthetic devices to bone. Special types of acrylic monomers such as the cyano derivatives have found a useful application as adhesive materials. Most of the acrylic acid esters are volatile substances and can produce various levels of toxicity if inhaled. A large number of workers thus exposed to the vapors of these esters can develop clinical symptoms and signs of toxicity. This paper will discuss the toxicity of a large number of acrylic esters, and will attempt to show structure-activity relationships where such data are available. General comments will also be made as to the potential health hazards this variety of esters may present to selected segments of the population. PMID:1175551

  18. Towards ontology personalization to enrich social conversations on AAC systems

    NASA Astrophysics Data System (ADS)

    Mancilla V., Daniela; Sastoque H., Sebastian; Iregui G., Marcela

    2015-01-01

    Communication is one of the essential needs of human beings. Augmentative and Alternative Communication Systems (AAC) seek to help in the generation of oral and written language to people with physical disorders that limit their natural communication. These systems present significant challenges such as: the composition of consistent messages according to syntactic and semantic rules, the improvement of message production times, the application to social contexts and, consequently, the incorporation of user-specific information. This work presents an original ontology personalization approach for an AAC instant messaging system incorporating personalized information to improve the efficacy and efficiency of the message production. This proposal is based on a projection of a general ontology into a more specific one, avoiding storage redundancy and data coupling, representing a big opportunity to enrich communication capabilities of current AAC systems. The evaluation was performed for a study case based on an AAC system for assistance in composing messages. The results show that adding user-specific information allows generation of enriched phrases, so improving the accuracy of the message, facilitating the communication process.

  19. AAC, Employment, and Independent Living: A Success Story

    ERIC Educational Resources Information Center

    Isakson, Carole L.; Burghstahler, Sheryl; Arnold, Anthony

    2006-01-01

    It has been well documented that individuals with significant physical disabilities who use augmentative and alternative communication (AAC) face considerable challenges in finding and maintaining employment. This article documents the experiences of one individual, Anthony Arnold, a young man who uses a Pathfinder[TM] for communication and a…

  20. Communication Partners Supporting Children with Complex Communication Needs Who Use AAC: A Systematic Review

    ERIC Educational Resources Information Center

    Shire, Stephanie Y.; Jones, Nancy

    2015-01-01

    Communication partners who efficiently use augmentative and alternative communication (AAC) are essential interaction partners for children learning to communicate using AAC. This systematic review examines studies targeting interventions designed to help communication partners support children with complex communication needs who use AAC.…

  1. Augmentative and Alternative Communication (AAC) and Inclusive Education for Students with the Most Severe Disabilities

    ERIC Educational Resources Information Center

    Calculator, Stephen N.

    2009-01-01

    This paper examines the role of augmentative and alternative communication (AAC) in fostering the successful inclusion of students with the most severe disabilities in general education. Best practices in AAC are identified and multiple examples of their implementation are presented. Particular emphasis is placed on the need to integrate AAC into…

  2. Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate

    SciTech Connect

    Binder, Thomas; Erpelding, Michael; Schmid, Josef; Chin, Andrew; Sammons, Rhea; Rockafellow, Erin

    2015-04-10

    Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate. The purpose of Archer Daniels Midlands Integrated Biorefinery (IBR) was to demonstrate a modified acetosolv process on corn stover. It would show the fractionation of crop residue to distinct fractions of cellulose, hemicellulose, and lignin. The cellulose and hemicellulose fractions would be further converted to ethanol as the primary product and a fraction of the sugars would be catalytically converted to acrylic acid, with butyl acrylate the final product. These primary steps have been demonstrated.

  3. Detection of aac(6')-I genes in amikacin-resistant Acinetobacter spp. by PCR.

    PubMed Central

    Ploy, M C; Giamarellou, H; Bourlioux, P; Courvalin, P; Lambert, T

    1994-01-01

    The distribution of aac(6')-I genes in 62 strains of Acinetobacter spp. resistant to amikacin, netilmicin, and tobramycin and susceptible to gentamicin, a phenotype compatible with synthesis of an AAC(6')-I enzyme, was studied by PCR and by DNA hybridization. Both methods gave similar results. Among the 51 Acinetobacter baumannii strains, aac(6')-Ib was found in 19 isolates and aac(6')-Ih was found in the remaining strains. The aac(6')-Ig gene was present in all 10 A. haemolyticus strains studied and was detected only in this species. A pair of degenerate oligonucleotides complementary to conserved regions of aac(6')-Ic, -Id, -If, -Ig, and -Ih enabled detection of these genes and also of aac(6')-Ij, recently recognized in Acinetobacter sp. strain 13. Images PMID:7695286

  4. N,N'-Dialkylaminoalkylcarbonyl (DAAC) prodrugs and aminoalkylcarbonyl (AAC) prodrugs of 4-hydroxyacetanilide and naltrexone with improved skin permeation properties.

    PubMed

    Devarajan-Ketha, H; Sloan, K B

    2011-07-01

    N,N'-Dialkylaminoalkylcarbonyl (DAAC) and aminoalkylcarbonyl (AAC) prodrugs of phenolic drugs acetaminophen (APAP) and naltrexone (NTX) are reported. The effects of incorporation of a basic amine group into the promoiety of an acyl prodrug of a phenolic drug on its skin permeation properties are also presented. DAAC-APAP prodrugs were synthesized via a three-step procedure starting with haloalkylcarbonyl esters which were reacted with five different amines: dimethylamine, diethylamine, dipropylamine, morpholine, and piperidine. The spacing between the amino group and the carbonyl group of the acyl group was 1-3 CH(2). After the hydrolysis of the ester, the carboxylic acid product was subsequently coupled with the parent drug via a dicyclohexyl carbodiimide (DCC) mediated coupling to yield the DAAC-APAP-HCl prodrugs in excellent yields. The AAC prodrugs were synthesized using commercially available Boc-protected amino acids using DCC or EDCI as coupling agents. The yields of the prodrugs synthesized using these two different methods have been compared. Half-lives (t(1/2)) of a few members of the DAAC and AAC series were measured in buffer (pH 6.0, 20mM). The members evaluated in hydrolysis experiments exhibit a t(1/2) range of 15-113min. Among AAC-APAP prodrugs, the isopropyl group in valinate-APAP-HCl exerted a steric effect that increased the t(1/2) value for this prodrug compared to alaninate-APAP-HCl or prolinate-APAP-HCl. The 2-morpholinylacetate-APAP prodrug was able to achieve twice the flux of APAP in in vitro diffusion cell experiments through hairless mouse skin. PMID:21616664

  5. Asian work choices: how AAC can liberate the user.

    PubMed

    Duckett, Nigel

    2010-07-01

    Each culture and nation has its own tradition concerning work and employment. There are varying attitudes towards what is considered real work, namely an activity that contributes to societal improvement. There is an immediate need to explore different cultural definitions of employment and how these might relate to a concept of individual independence. For users of augmentative and alternative communication (AAC), greater competence leads to a better chance of involvement and inclusion in society. A natural consequence is a desire to contribute and be rewarded. Without a voice, work choices become extremely limited. By contrasting the American and European experiences with the expectations of people with speech impairments living in Asia, insight can be gained into the true value of AAC implementation. PMID:20331414

  6. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  7. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  8. FT-IR and FT-Raman studies of cross-linking processes with Ca(2+) ions, glutaraldehyde and microwave radiation for polymer composition of poly(acrylic acid)/sodium salt of carboxymethyl starch--part I.

    PubMed

    Grabowska, Beata; Sitarz, Maciej; Olejnik, Ewa; Kaczmarska, Karolina

    2015-01-25

    FT-IR and FT-Raman spectroscopic methods allowed to identify the cross-linking process of the aqueous composition of poly(acrylic acid)/sodium salt of carboxymethyl starch (PAA/CMS-Na) applied as a binder for moulding sands. The cross-linking was performed by chemical methods by introducing cross-linking substances with Ca(2+) ions or glutaraldehyde and by physical way, applying the microwave radiation. It was found that Ca(2+) ions cause formation of cross-linking ionic bonds within carboxyl and carboxylate groups. Glutaraldehyde generates formation of cross-linking bonds with hemiacetal and acetal structures. Whereas in the microwave radiation field, due to dehydration, lattices are formed by anhydride bonds. PMID:25123942

  9. Constrained photophysics of partially and fully encapsulated charge transfer probe (E)-3-(4-Methylaminophenyl) acrylic acid methyl ester inside cyclodextrin nano-cavities: Evidence of cyclodextrins cavity dependent complex stoichiometry

    NASA Astrophysics Data System (ADS)

    Ghosh, Shalini; Jana, Sankar; Guchhait, Nikhil

    2011-12-01

    The polarity sensitive intra-molecular charge transfer (ICT) emission from (E)-3-(4-Methylaminophenyl) acrylic acid methyl ester (MAPAME) is found to show distinct changes once introduced into the nano-cavities of cyclodextrins in aqueous environment. Movement of the molecule from the more polar aqueous environment to the less polar, hydrophobic cyclodextrin interior is marked by the blue shift of the CT emission band with simultaneous fluorescence intensity enhancement. The emission spectral changes on complexation with the α- and β-CD show different stoichiometries as observed from the Benesi-Hildebrand plots. Fluorescence anisotropy and lifetime measurements were performed to probe the different behaviors of MAPAME in aqueous α- and β-CD solutions.

  10. Constrained photophysics of partially and fully encapsulated charge transfer probe (E)-3-(4-Methylaminophenyl) acrylic acid methyl ester inside cyclodextrin nano-cavities: evidence of cyclodextrins cavity dependent complex stoichiometry.

    PubMed

    Ghosh, Shalini; Jana, Sankar; Guchhait, Nikhil

    2011-12-15

    The polarity sensitive intra-molecular charge transfer (ICT) emission from (E)-3-(4-Methylaminophenyl) acrylic acid methyl ester (MAPAME) is found to show distinct changes once introduced into the nano-cavities of cyclodextrins in aqueous environment. Movement of the molecule from the more polar aqueous environment to the less polar, hydrophobic cyclodextrin interior is marked by the blue shift of the CT emission band with simultaneous fluorescence intensity enhancement. The emission spectral changes on complexation with the α- and β-CD show different stoichiometries as observed from the Benesi-Hildebrand plots. Fluorescence anisotropy and lifetime measurements were performed to probe the different behaviors of MAPAME in aqueous α- and β-CD solutions. PMID:21996591

  11. [Treatment of acrylate wastewater by electrocatalytic reduction process].

    PubMed

    Yu, Li-Na; Song, Yu-Dong; Zhou, Yue-Xi; Zhu, Shu-Quan; Zheng, Sheng-Zhi; Ll, Si-Min

    2011-10-01

    High-concentration acrylate wastewater was treated by an electrocatalytic reduction process. The effects of the cation exchange membrane (CEM) and cathode materials on acrylate reduction were investigated. It indicated that the acrylate could be reduced to propionate acid efficiently by the electrocatalytic reduction process. The addition of CEM to separator with the cathode and anode could significantly improve current efficiency. The cathode materials had significant effect on the reduction of acrylate. The current efficiency by Pd/Nickel foam, was greater than 90%, while those by nickel foam, the carbon fibers and the stainless steel decreased successively. Toxicity of the wastewater decreased considerably and methane production rate in the biochemical methane potential (BMP) test increased greatly after the electrocatalytic reduction process. PMID:22279908

  12. Adsorption mechanism and dispersion efficiency of three anionic additives [poly(acrylic acid), poly(styrene sulfonate) and HEDP] on zinc oxide.

    PubMed

    Dange, C; Phan, T N T; André, V; Rieger, J; Persello, J; Foissy, A

    2007-11-01

    Adsorption on ZnO of sodium poly(acrylate) (PAA), sodium poly(styrene sulfonate) (PSS) and a monomer surfactant [hydroxyethylidene diphosphonate (HEDP)] was investigated in suspensions initially equilibrated at pH 7. Results demonstrate interplay in the adsorption mechanism between zinc complexation, salt precipitation, and ZnO dissolution. In the case of PAA, the adsorption isotherm exhibits a maximum attributed to the precipitation of zinc polyacrylate. PSS and HEDP formed high-affinity adsorption isotherms, but the plateau adsorption of HEDP was significantly lower than that of PSS. The adsorption isotherm of each additive is divided into two areas. At low additive concentration (high zinc/additive ratio), the total zinc concentration in the solution decreased and the pH increased upon addition. At a higher additive ratio, zinc concentration and pH increased with the organic concentration. The increase in pH is due to the displacement of hydroxyl ions from the surface and the increase in zinc concentration results from the dissolution of ZnO due to the complexation of zinc ions by the organics. The stability of the ZnO dispersions was investigated by measurement of the particle size distribution after addition of various amounts of polymers. The three additives stabilized the ZnO dispersions efficiently once full surface coverage was reached. PMID:17720181

  13. Preparation and properties of UV curable acrylic PSA by vinyl bonded graphene oxide

    NASA Astrophysics Data System (ADS)

    Pang, Beili; Ryu, Chong-Min; Jin, Xin; Kim, Hyung-Il

    2013-11-01

    Acrylic pressure sensitive adhesives (PSAs) with higher thermal stability for thin wafer handling were successfully prepared by forming composite with the graphene oxide (GO) nanoparticles modified to have vinyl groups via subsequent reaction with isophorone diisocyanate and 2-hydroxyethyl methacrylate. The acrylic copolymer was synthesized as a base resin for PSAs by solution radical polymerization of ethyl acrylate, 2-ethylhexyl acrylate, and acrylic acid followed by further modification with GMA to have the vinyl groups available for UV curing. The peel strength of PSA decreased with the increase of gel content which was dependent on both modified GO content and UV dose. Thermal stability of UV-cured PSA was improved noticeably with increasing the modified GO content mainly due to the strong and extensive interfacial bonding formed between the acrylic copolymer matrix and GO fillers

  14. Epoxy-acrylic core-shell particles by seeded emulsion polymerization.

    PubMed

    Chen, Liang; Hong, Liang; Lin, Jui-Ching; Meyers, Greg; Harris, Joseph; Radler, Michael

    2016-07-01

    We developed a novel method for synthesizing epoxy-acrylic hybrid latexes. We first prepared an aqueous dispersion of high molecular weight solid epoxy prepolymers using a mechanical dispersion process at elevated temperatures, and we subsequently used the epoxy dispersion as a seed in the emulsion polymerization of acrylic monomers comprising methyl methacrylate (MMA) and methacrylic acid (MAA). Advanced analytical techniques, such as scanning transmission X-ray microscopy (STXM) and peak force tapping atomic force microscopy (PFT-AFM), have elucidated a unique core-shell morphology of the epoxy-acrylic hybrid particles. Moreover, the formation of the core-shell morphology in the seeded emulsion polymerization process is primarily attributed to kinetic trapping of the acrylic phase at the exterior of the epoxy particles. By this new method, we are able to design the epoxy and acrylic polymers in two separate steps, and we can potentially synthesize epoxy-acrylic hybrid latexes with a broad range of compositions. PMID:27078740

  15. Advances in acrylic-alkyd hybrid synthesis and characterization

    NASA Astrophysics Data System (ADS)

    Dziczkowski, Jamie

    2008-10-01

    In situ graft acrylic-alkyd hybrid resins were formed by polymerizing acrylic and acrylic-mixed monomers in the presence of alkyds by introduction of a free radical initiator to promote graft formation. Two-dimensional NMR, specifically gradient heteronuclear multiple quantum coherence (gHMQC), was used to clarify specific graft sites of the hybrid materials. Both individual and mixed-monomer systems were produced to determine any individual monomer preferences and to model current acrylic-alkyd systems. Different classes of initiators were used to determine any initiator effects on graft location. The 2D-NMR results confirm grafting at doubly allylic hydrogens located on the fatty acid chains and the polyol segment of the alkyd backbone. The gHMQC spectra show no evidence of grafting across double bonds on either pendant fatty acid groups or THPA unsaturation sites for any of the monomer or mixed monomer systems. It was also determined that choice of initiator has no effect on graft location. In addition, a design of experiments using response surface methodology was utilized to obtain a better understanding of this commercially available class of materials and relate both the chemical and physical properties to one another. A Box-Behnkin design was used, varying the oil length of the alkyd phase, the degree of unsaturation in the polyester backbone, and acrylic to alkyd ratio. Acrylic-alkyd hybrid resins were reduced with an amine/water mixture. Hydrolytic stability was tested and viscoelastic properties were obtained to determine crosslink density. Cured films were prepared and basic coatings properties were evaluated. It was found that the oil length of the alkyd is the most dominant factor for final coatings properties of the resins. Acrylic to alkyd ratio mainly influences the resin properties such as acid number, average molecular weight, and hydrolytic stability. The degree of unsaturation in the alkyd backbone has minimal effects on resin and film

  16. Multidrug-Resistant Pseudomonas aeruginosa Strain That Caused an Outbreak in a Neurosurgery Ward and Its aac(6′)-Iae Gene Cassette Encoding a Novel Aminoglycoside Acetyltransferase

    PubMed Central

    Sekiguchi, Jun-ichiro; Asagi, Tsukasa; Miyoshi-Akiyama, Tohru; Fujino, Tomoko; Kobayashi, Intetsu; Morita, Koji; Kikuchi, Yoshihiro; Kuratsuji, Tadatoshi; Kirikae, Teruo

    2005-01-01

    We characterized multidrug-resistant Pseudomonas aeruginosa strains isolated from patients involved in an outbreak of catheter-associated urinary tract infections that occurred in a neurosurgery ward of a hospital in Sendai, Japan. Pulsed-field gel electrophoresis of SpeI-, XbaI-, or HpaI-digested genomic DNAs from the isolates revealed that clonal expansion of a P. aeruginosa strain designated IMCJ2.S1 had occurred in the ward. This strain possessed broad-spectrum resistance to aminoglycosides, β-lactams, fluoroquinolones, tetracyclines, sulfonamides, and chlorhexidine. Strain IMCJ2.S1 showed a level of resistance to some kinds of disinfectants similar to that of a control strain of P. aeruginosa, ATCC 27853. IMCJ2.S1 contained a novel class 1 integron, In113, in the chromosome but not on a plasmid. In113 contains an array of three gene cassettes of blaIMP-1, a novel aminoglycoside resistance gene, and the aadA1 gene. The aminoglycoside resistance gene, designated aac(6′)-Iae, encoded a 183-amino-acid protein that shared 57.1% identity with AAC(6′)-Iq. Recombinant AAC(6′)-Iae protein showed aminoglycoside 6′-N-acetyltransferase activity by thin-layer chromatography. Escherichia coli expressing exogenous aac(6′)-Iae showed resistance to amikacin, dibekacin, isepamicin, kanamycin, netilmicin, sisomicin, and tobramycin but not to arbekacin, gentamicins, or streptomycin. Alterations of gyrA and parC at the amino acid sequence level were detected in IMCJ2.S1, suggesting that such mutations confer the resistance to fluoroquinolones observed for this strain. These results indicate that P. aeruginosa IMCJ2.S1 has developed multidrug resistance by acquiring resistance determinants, including a novel member of the aac(6′)-I family and mutations in drug resistance genes. PMID:16127047

  17. The acute aquatic toxicity of a series of acrylate and methacrylate esters

    SciTech Connect

    Staples, C.A.; McLaughlin, J.E.; Hamilton, J.D.

    1994-12-31

    Acute aquatic toxicity data for several acrylate and methacrylate esters were reviewed. Acrylates included acrylic acid, ethyl-, and butyl-acrylate. Methacrylates included methacrylic acid, methyl-, and butyl-methacrylate. Tests were 48 hr or 96 hr standard flow through (invertebrates and fish) assays (measured exposure concentrations). These data are currently used in a risk assessment of acrylate/methacrylate environmental safety. Algal growth (Selanastrum capricomutum) 96 hr EC{sub 50}s were 0.17 mg/L (NOEC < 0.13 mg/L) for acrylic acid, 11.0 mg/L (NOEC < 6.5 mg/L) for ethyl acrylate, and 5.2 mg/L (NOEC < 3.8 mg/L) for butyl acrylate. Invertebrate (Daphnia magna) 48 hr LC{sub 50}s were 95.0 mg/L (NOEC 23.0 mg/L) for acrylic acid, 7.9 mg/L (NOEC 3.4 mg/L) for ethyl acrylate, and 8.2 mg/L (NOEC 2.4 mg/L) for butyl acrylate. Rainbow trout (Oncorhynchus mykiss) 96 hr LC{sub 50}s were 27.0 mg/L (NOEC 6.3 mg/L) for acrylic acid, 4.6 mg/L (NOEC 0.78 mg/L) for ethyl acrylate, and 5.2 mg/L (NOEC 3.8 mg/L) for butyl acrylate. Algae 96 hr EC{sub 50}s were 0.59 mg/L (NOEC 0.38 mg/L) for methacrylic acid, 170.0 mg/L (NOEC 100.0 mg/L) for methyl methacrylate, and 130.0 mg/L for butyl methacrylate. Daphnia magna 48 hr LC{sub 50}s were > 130.0 mg/L (NOEC 130.0 mg/L) for methacrylic acid, 69.0 mg/L (NOEC 48.0 mg/L) for methyl methacrylate, and 32.0 mg/L (NOEC 23.0 mg/L) for butyl methacrylate. Trout 96 hr LC{sub 50}s were 85.0 mg/L (NOEC 12.0 mg/L) for methacrylic acid and > 79.0 mg/L (NOEC 40.0 mg/L) for methyl methacrylate. The fathead minnow (Pimephales promelas) 96 hr LC{sub 50} was 11.0 mg/L for butyl methacrylate.

  18. PMQR genes oqxAB and aac(6′)Ib-cr accelerate the development of fluoroquinolone resistance in Salmonella typhimurium

    PubMed Central

    Wong, Marcus H.; Chan, Edward W.; Liu, Li Z.; Chen, Sheng

    2014-01-01

    Emergence of multidrug-resistant Salmonella typhimurium strains, especially the ACSSuT and nalidixic acid R types, has significantly compromised the effectiveness of current strategies to control Salmonella infections, resulting in increased morbidity and mortality. Clinical S. typhimurium isolates recovered in Hong Kong during the period of 2005–2011 were increasingly resistant to ciprofloxacin (CIP) and antibiotics of the ACSSuT group. Our data revealed that oqxAB and aac(6′)Ib-cr were encoded on plasmids of various sizes and the presence of these two elements together with a single gyrA mutation in S. typhimurium were sufficient to mediate resistance to CIP. Acquisition of the oqxAB and aac(6′)Ib-cr encoding plasmids by S. typhimurium caused a fourfold increase in CIP minimal inhibitory concentration. Furthermore, the presence of oqxAB and aac(6′)Ib-cr in Salmonella dramatically increased the mutation prevention concentration of CIP which may due to mutational changes in the drug target genes. In conclusion, possession of oqxAB and aac(6′)Ib-cr encoding plasmid facilitate the selection of CIP resistant S. typhimurium, thereby causing a remarkable increase of CIP resistance among clinical Salmonella strains in Hong Kong. PMID:25324840

  19. iCataly-PseAAC: Identification of Enzymes Catalytic Sites Using Sequence Evolution Information with Grey Model GM (2,1).

    PubMed

    Xiao, Xuan; Hui, Meng-Juan; Liu, Zi; Qiu, Wang-Ren

    2015-12-01

    Enzymes play pivotal roles in most of the biological reaction. The catalytic residues of an enzyme are defined as the amino acids which are directly involved in chemical catalysis; the knowledge of these residues is important for understanding enzyme function. Given an enzyme, which residues are the catalytic sites, and which residues are not? This is the first important problem for in-depth understanding the catalytic mechanism and drug development. With the explosive of protein sequences generated during the post-genomic era, it is highly desirable for both basic research and drug design to develop fast and reliable method for identifying the catalytic sites of enzymes according to their sequences. To address this problem, we proposed a new predictor, called iCataly-PseAAC. In the prediction system, the peptide sample was formulated with sequence evolution information via grey system model GM(2,1). It was observed by the rigorous jackknife test and independent dataset test that iCataly-PseAAC was superior to exist predictions though its only use sequence information. As a user-friendly web server, iCataly-PseAAC is freely accessible at http://www.jci-bioinfo.cn/iCataly-PseAAC. A step-by-step guide has been provided on how to use the web server to get the desired results for the convenience of most experimental scientists. PMID:26077845

  20. AACE: an innovative partnership to enhance aircraft safety

    NASA Astrophysics Data System (ADS)

    Shurtleff, William W.

    1999-01-01

    The Federal Aviation Administration established the Airworthiness Assurance Center of Excellence (AACE) in September 1997, through a cooperative agreement grant with Iowa State University (ISU) and The Ohio State University (OSU). A technical support contract with the Center is now in place as well. Initially the Center has five areas of concentration supporting advances in airworthiness assurance. These are 1. Maintenance, inspection, and repair, 2. Propulsion and fuel systems safety, 3. Crashworthiness, 4. Advanced materials, and 5. Landing gear systems performance and safety. AACE has nine core members who provide guidance to the Program Management Office at ISU/OSU through a Board of Directors. The core members are: Arizona State University, Iowa State University, Northwestern University, The Ohio State University, University of Dayton, University of Maryland, University of California - Los Angeles, Wichita State University, and Sandia National Laboratories. The organization also includes numerous academic affiliates, industry partners, government laboratories and other organizations. The Center now has over thirty technical projects supporting technical advances in airworthiness assurance. All these projects have industry guidance and support. This paper discusses the current technical program of the center and the highlights of the five-year plan for technical work. Also included is a description of the factors that make the Center an innovative partnership to promote aircraft safety.

  1. AAC Modeling with the iPad during Shared Storybook Reading Pilot Study

    ERIC Educational Resources Information Center

    Sennott, Samuel C.; Mason, Linda H.

    2016-01-01

    This pilot study describes an intervention package, MODELER for Read and Talk, designed to provide enriched language interaction for children with complex communication needs who require augmentative and alternative communication (AAC). MODELER (Model, Encourage, Respond) includes (a) modeling AAC as you speak, (b) encouraging communication…

  2. Challenge and Response: Integrity and AAC&U's Reform Initiatives, 1985-1994

    ERIC Educational Resources Information Center

    Schneider, Carol Geary

    2014-01-01

    Ten years ago, AAC&U (then AAC) issued a landmark report, "Integrity in the College Curriculum: A Report to the Academic Community". Anticipating the academy's sternest external critics by nearly a decade, "Integrity" offered a sweeping and incisive critique of curricular practice throughout higher education. "As for…

  3. Interaction of Participant Characteristics and Type of AAC with Individuals with ASD: A Meta-Analysis

    ERIC Educational Resources Information Center

    Ganz, Jennifer B.; Mason, Rose A.; Goodwyn, Fara D.; Boles, Margot B.; Heath, Amy K.; Davis, John L.

    2014-01-01

    Individuals with autism spectrum disorders (ASD) and complex communication needs often rely on augmentative and alternative communication (AAC) as a means of functional communication. This meta-analysis investigated how individual characteristics moderate effectiveness of three types of aided AAC: the Picture Exchange Communication System (PECS),…

  4. An Investigation of the Efficacy of Direct and Indirect AAC Service Provision via Telepractice

    ERIC Educational Resources Information Center

    Hall, Nerissa C.

    2013-01-01

    There is a growing population of individuals using Augmentative and Alternative Communication (AAC) in need of evidence-based intervention from highly qualified personnel. However, not all speech pathology programs offer AAC coursework and/or practicum opportunities, and practicing speech-language pathologists (SLPs) report low levels of…

  5. The Influence of AAC Device Type, Dynamic vs. Static Screen, on Peer Attitudes

    ERIC Educational Resources Information Center

    Dudek, Karen; Beck, Ann R.; Thompson, James R.

    2006-01-01

    This study examined how children's attitudes toward a peer who used augmentative and alternative communication (AAC) were influenced by type of AAC device accessed by the child for communication. Specifically, the influence of dynamic screens vs. static screens was investigated. Two videotapes were created. In one a child used a dynamic screen…

  6. Keep Your Eye on the Prize: Implementing AAC within the Broader Context of Communicative Competence

    ERIC Educational Resources Information Center

    DeThorne, Laura Segebart; Hengst, Julie; Fisher, Kim; King, Amie

    2014-01-01

    Electronic technologies are playing an increasing role in mediating patterns of social interaction within the classroom. This trend includes augmentative and alternative communication (AAC) systems like light-weight smart tablets. AAC in general has proven effective for many children in regard to decreasing challenging behavior, enabling…

  7. Implementing AAC with Children with Profound and Multiple Learning Disabilities: A Study in Rationale Underpinning Intervention

    ERIC Educational Resources Information Center

    Harding, Celia; Lindsay, Gemma; O'Brien, Aoife; Dipper, Lucy; Wright, Julie

    2011-01-01

    There is a developing research base to support the rationale underpinning augmentative and alternative communication (AAC) for people with learning disabilities. However, there is a paucity of research examining the process involved in implementing AAC support for people who have profound disabilities. This paper seeks to explore the processes…

  8. Degradation of a Sodium Acrylate Oligomer by an Arthrobacter sp

    PubMed Central

    Hayashi, Takaya; Mukouyama, Masaharu; Sakano, Kouichi; Tani, Yoshiki

    1993-01-01

    Arthrobacter sp. strain NO-18 was first isolated from soil as a bacterium which could degrade the sodium acrylate oligomer and utilize it as the sole source of carbon. When 0.2% (wt/wt) oligomer was added to the culture medium, the acrylate oligomer was found to be degraded by 70 to 80% in 2 weeks, using gel permeation chromatography. To determine the maximum molecular weight for biodegradation, the degradation test was done with the hexamer, heptamer, and octamer, which were separated from the oligomer mixture by fractional gel permeation chromatography. The hexamer and heptamer were consumed to the extents of 58 and 36%, respectively, in 2 weeks, but the octamer was not degraded. Oligomers with three different terminal groups were synthesized to examine the effect of the different terminal groups on biodegradation, but few differences were found. Arthrobacter sp. NO-18 assimilated acrylic acid, propionic acid, glutaric acid, 2-methylglutaric acid, and 1,3,5-pentanetricarboxylic acid. Degradation of the acrylic unit structure by this strain is discussed. PMID:8517751

  9. Properties of extruded starch-poly(methyl acrylate) graft copolymers prepared from spherulites formed from amylose-oleic acid inclusion complexes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Mixtures of high amylose corn starch and oleic acid were processed by steam jet-cooking, and the dispersions were rapidly cooled to yield amylose-oleic acid inclusion complexes as sub-micron spherulites and spherulite aggregates. Dispersions of these spherulite particles were then graft polymerized ...

  10. Synthesis of Radiation Curable Palm Oil-Based Epoxy Acrylate: NMR and FTIR Spectroscopic Investigations.

    PubMed

    Salih, Ashraf M; Ahmad, Mansor Bin; Ibrahim, Nor Azowa; Dahlan, Khairul Zaman Hj Mohd; Tajau, Rida; Mahmood, Mohd Hilmi; Yunus, Wan Md Zin Wan

    2015-01-01

    Over the past few decades, there has been an increasing demand for bio-based polymers and resins in industrial applications, due to their potential lower cost and environmental impact compared with petroleum-based counterparts. The present research concerns the synthesis of epoxidized palm oil acrylate (EPOLA) from an epoxidized palm oil product (EPOP) as environmentally friendly material. EPOP was acrylated by acrylic acid via a ring opening reaction. The kinetics of the acrylation reaction were monitored throughout the reaction course and the acid value of the reaction mixture reached 10 mg KOH/g after 16 h, indicating the consumption of the acrylic acid. The obtained epoxy acrylate was investigated intensively by means of FTIR and NMR spectroscopy, and the results revealed that the ring opening reaction was completed successfully with an acrylation yield about 82%. The UV free radical polymerization of EPOLA was carried out using two types of photoinitiators. The radiation curing behavior was determined by following the conversion of the acrylate groups. The cross-linking density and the hardness of the cured EPOLA films were measured to evaluate the effect of the photoinitiator on the solid film characteristics, besides, the thermal and mechanical properties were also evaluated. PMID:26248072

  11. Interaction of participant characteristics and type of AAC with individuals with ASD: a meta-analysis.

    PubMed

    Ganz, Jennifer B; Mason, Rose A; Goodwyn, Fara D; Boles, Margot B; Heath, Amy K; Davis, John L

    2014-11-01

    Individuals with autism spectrum disorders (ASD) and complex communication needs often rely on augmentative and alternative communication (AAC) as a means of functional communication. This meta-analysis investigated how individual characteristics moderate effectiveness of three types of aided AAC: the Picture Exchange Communication System (PECS), speech-generating devices (SGDs), and other picture-based AAC. Effectiveness was measured via the Improvement Rate Difference. Results indicated that AAC has small to moderate effects on speech outcomes, and that SGDs appear to be most effective when considering any outcome measure with individuals with ASD without comorbid intellectual/developmental disorders (IDD). PECS appears to be most effective when considering any outcome measure with individuals with ASD and IDD. SGDs and PECS were the most effective type of AAC for preschoolers, when aggregating across outcome measures. No difference was found between systems for elementary-aged and older individuals. PMID:25354122

  12. Investigation of Changes in the Microscopic Structure of Anionic Poly(N-isopropylacrylamide-co-Acrylic acid) Microgels in the Presence of Cationic Organic Dyes toward Precisely Controlled Uptake/Release of Low-Molecular-Weight Chemical Compound.

    PubMed

    Kureha, Takuma; Shibamoto, Takahisa; Matsui, Shusuke; Sato, Takaaki; Suzuki, Daisuke

    2016-05-10

    Changes in a microscopic structure of an anionic poly(N-isopropylacrylamide-co-acrylic acid) microgel were investigated using small- and wide-angle X-ray scattering (SWAXS). The scattering profiles of the microgels were analyzed in a wide scattering vector (q) range of 0.07 ≤ q/nm(-1) ≤ 20. In particular, the microscopic structure of the microgel in the presence of a cationic dye rhodamine 6G (R6G) was characterized in terms of its correlation length (ξ), which represents the length scale of the spatial correlation of the network density fluctuations, and characteristic distance (d*), which originated from the local packing of isopropyl groups of two neighboring chains. In the presence of cationic R6G, ξ exhibited a divergent-like behavior, which was not seen in the absence of R6G, and d* was decreased with decreasing the volume of the microgel upon increasing temperature. At the same time, the amount of R6G adsorbed per unit mass of the microgel increased upon heating. These results suggested that a coil-to-globule transition of the poly(N-isopropylacrylamide) chains in the present anionic microgel occurred because of efficiently screened, thus, short ranged electrostatic repulsion between the charged groups, and hydrophobic interaction between the isopropyl groups in the presence of cationic R6G. The combination of hydrophobic and electrostatic interaction between the cationic dye and the microgel affected the separation and volume transition behavior of the microgel. PMID:27101468

  13. Selective electrochemical detection of 2,4,6-trinitrotoluene (TNT) in water based on poly(styrene-co-acrylic acid) PSA/SiO2/Fe3O4/AuNPs/lignin-modified glassy carbon electrode.

    PubMed

    Mahmoud, Khaled A; Abdel-Wahab, Ahmed; Zourob, Mohammed

    2015-01-01

    A new versatile electrochemical sensor based on poly(styrene-co-acrylic acid) PSA/SiO2/Fe3O4/AuNPs/lignin (L-MMS) modified glassy carbon electrode (GCE) was developed for the selective detection of trace trinitrotoluene (TNT) from aqueous media with high sensitivity. The fabricated magnetic microspheres were characterized by transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). L-MMS films were cast on the GCE surface to fabricate the TNT sensing electrode. The limit of detection (LOD) of TNT determined by the amperometric i-t curve reached 35 pM. The lignin film and well packed Fe3O4/AuNPs facilitated the pre-concentration of trace TNT on the electrode surface resulting in a fast amperometric response of 3 seconds near the detection limit. The high sensitivity and excellent catalytic activity of the modified electrode could be attributed to the lignin layer and highly packed Fe3O4/AuNPs on the electrode surface. The total recovery of TNT from tapwater and seawater matrices was 98% and 96%, respectively. The electrode film was highly stable after five repeated adsorption/desorption cycles. The new electrochemical sensing scheme provides a highly selective, sensitive and versatile assay for the in-situ detection of TNT in complex water media. PMID:26540539

  14. Carbohydrate CuAAC click chemistry for therapy and diagnosis.

    PubMed

    He, Xiao-Peng; Zeng, Ya-Li; Zang, Yi; Li, Jia; Field, Robert A; Chen, Guo-Rong

    2016-06-24

    Carbohydrates are important as signaling molecules and for cellular recognition events, therefore offering scope for the development of carbohydrate-mimetic diagnostics and drug candidates. As a consequence, the construction of carbohydrate-based bioactive compounds and sensors has become an active research area. While the advent of click chemistry has greatly accelerated the progress of medicinal chemistry and chemical biology, recent literature has seen an extensive use of such approaches to construct functionally diverse carbohydrate derivatives. Here we summarize some of the progress, covering the period 2010 to mid-2015, in Cu(I)-catalyzed azide-alkyne 1,3-dipolar cycloaddition CuAAC "click chemistry" of carbohydrate derivatives, in the context of potential therapeutic and diagnostic tool development. PMID:27085906

  15. Literacy learning in users of AAC: A neurocognitive perspective.

    PubMed

    Van Balkom, Hans; Verhoeven, Ludo

    2010-09-01

    The understanding of written or printed text or discourse - depicted either in orthographical, graphic-visual or tactile symbols - calls upon both bottom-up word recognition processes and top-down comprehension processes. Different architectures have been proposed to account for literacy processes. Research has shown that the first steps in perceiving, processing and deriving conceptual meaning from words, graphic symbols, manual signs, and co-speech gestures or tactile manual signing and tangible symbols can be seen as identical and collectively (sub)activated. Results from recent brain research and neurolinguistics have revealed new insights in the reading process of typical and atypical readers and may provide verifiable evidence for improved literacy assessment and the validation of early intervention programs for AAC users. PMID:20874078

  16. Lactate and Acrylate Metabolism by Megasphaera elsdenii under Batch and Steady-State Conditions

    PubMed Central

    Prabhu, Rupal; Altman, Elliot

    2012-01-01

    The growth of Megasphaera elsdenii on lactate with acrylate and acrylate analogues was studied under batch and steady-state conditions. Under batch conditions, lactate was converted to acetate and propionate, and acrylate was converted into propionate. Acrylate analogues 2-methyl propenoate and 3-butenoate containing a terminal double bond were similarly converted into their respective saturated acids (isobutyrate and butyrate), while crotonate and lactate analogues 3-hydroxybutyrate and (R)-2-hydroxybutyrate were not metabolized. Under carbon-limited steady-state conditions, lactate was converted to acetate and butyrate with no propionate formed. As the acrylate concentration in the feed was increased, butyrate and hydrogen formation decreased and propionate was increasingly generated, while the calculated ATP yield was unchanged. M. elsdenii metabolism differs substantially under batch and steady-state conditions. The results support the conclusion that propionate is not formed during lactate-limited steady-state growth because of the absence of this substrate to drive the formation of lactyl coenzyme A (CoA) via propionyl-CoA transferase. Acrylate and acrylate analogues are reduced under both batch and steady-state growth conditions after first being converted to thioesters via propionyl-CoA transferase. Our findings demonstrate the central role that CoA transferase activity plays in the utilization of acids by M. elsdenii and allows us to propose a modified acrylate pathway for M. elsdenii. PMID:23023753

  17. Biocatalytic functionalization of hydroxyalkyl acrylates and phenoxyethanol via phosphorylation.

    PubMed

    Tasnádi, Gábor; Hall, Mélanie; Baldenius, Kai; Ditrich, Klaus; Faber, Kurt

    2016-09-10

    The enzymatic phosphorylation of phenoxyethanol, 2-hydroxyethyl acrylate and 4-hydroxybutyl acrylate catalyzed by acid phosphatases PhoN-Sf and PiACP at the expense of inorganic di-, tri-, hexameta- or polyphosphate was applied to the preparative-scale synthesis of phosphorylated compounds. The reaction conditions were optimized with respect to enzyme immobilization, substrate concentration, pH and type of phosphate donor. The mild reaction conditions prevented undesired polymerization and hydrolysis of the acrylate ester moiety. Application of a continuous flow system allowed facile scale-up and mono-phosphates were obtained in up to 26% isolated yield with space-time yields of 0.89kgL(-1)h(-1). PMID:27422352

  18. Using NMR chemical shift imaging to monitor swelling and molecular transport in drug-loaded tablets of hydrophobically modified poly(acrylic acid): methodology and effects of polymer (in)solubility.

    PubMed

    Knöös, Patrik; Topgaard, Daniel; Wahlgren, Marie; Ulvenlund, Stefan; Piculell, Lennart

    2013-11-12

    A new technique has been developed using NMR chemical shift imaging (CSI) to monitor water penetration and molecular transport in initially dry polymer tablets that also contain small low-molecular weight compounds to be released from the tablets. Concentration profiles of components contained in the swelling tablets could be extracted via the intensities and chemical shift changes of peaks corresponding to protons of the components. The studied tablets contained hydrophobically modified poly(acrylic acid) (HMPAA) as the polymer component and griseofulvin and ethanol as hydrophobic and hydrophilic, respectively, low-molecular weight model compounds. The water solubility of HMPAA could be altered by titration with NaOH. In the pure acid form, HMPAA tablets only underwent a finite swelling until the maximum water content of the polymer-rich phase, as confirmed by independent phase studies, had been reached. By contrast, after partial neutralization with NaOH, the polyacid became fully miscible with water. The solubility of the polymer affected the water penetration, the polymer release, and the releases of both ethanol and griseofulvin. The detailed NMR CSI concentration profiles obtained highlighted the clear differences in the disintegration/dissolution/release behavior for the two types of tablet and provided insights into their molecular origin. The study illustrates the potential of the NMR CSI technique to give information of importance for the development of pharmaceutical tablets and, more broadly, for the general understanding of any operation that involves the immersion and ultimate disintegration of a dry polymer matrix in a solvent. PMID:24106807

  19. Mutagenicity assessment of acrylate and methacrylate compounds and implications for regulatory toxicology requirements.

    PubMed

    Johannsen, F R; Vogt, Barbara; Waite, Maureen; Deskin, Randy

    2008-04-01

    Esters of acrylic acid and methacrylic acid, more commonly known as acrylates and methacrylates, respectively, are key raw materials in the coatings and printing industry, with several of its chemical class used in food packaging. The results of over 200 short-term in vitro and in vivo mutagenicity studies available in the open literature have been evaluated. Despite differences in acrylate or methacrylate functionality or in the number of functional groups, a consistent pattern of test response was seen in a typical regulatory battery of mutagenicity tests. No evidence of point mutations was observed when acrylic acid or over 60 acrylates and methacrylates were investigated in Salmonella bacterial tests or in hprt mutation tests mammalian cells, and no evidence of a mutagenic effect was seen when tested in whole animal clastogenicity and/or aneuploidy (chromosomal aberration/micronucleus) studies. Consistent with the in vivo testing results, acrylic acid exhibited no evidence of carcinogenicity in chronic rodent cancer bioassays. In contrast, acrylic acid and the entire acrylate and methacrylate chemical class produced a consistently positive response when tested in the mouse lymphoma assay and/or other in vitro mammalian cell assays designed to detect clastogenicity. The biological relevance of this in vitro response is questioned based on the non-concordance of in vitro results with those of in vivo studies addressing the same mutagenic endpoint (clastogenicity). Thus, in short-term mutagenicity tests, the acrylates and methacrylates behave as a single chemical category, and genotoxicity behavior of a similar chemical can be predicted with confidence by inclusion within this chemical class, thus avoiding unnecessary testing. PMID:18346829

  20. Characterization of Tn6238 with a New Allele of aac(6′)-Ib-cr

    PubMed Central

    Quiroga, María P.; Orman, Betina; Errecalde, Laura; Kaufman, Sara

    2015-01-01

    Here, we report that the genetic structure of Tn1331 remained conserved in Argentina from 1989 to 2013 (72 of 73 isolates), with the exception being the plasmid-borne Tn1331-like transposon Tn6238 containing a new aac(6′)-Ib-cr allele recovered from a colistin-resistant Klebsiella pneumoniae clinical isolate. A bioinformatic analysis of aac(6′)-Ib-like gene cassettes suggests that this new aac(6′)-Ib-cr allele emerged through mutation or homologous recombination in the Tn1331 genetic platform. Tn6238 is a novel platform for the dissemination of aminoglycoside and fluoroquinolone resistance determinants. PMID:25691640

  1. Cysteine as a Monothiol Reducing Agent to Prevent Copper-Mediated Oxidation of Interferon Beta During PEGylation by CuAAC.

    PubMed

    Nairn, Natalie W; Bariola, Pauline A; Graddis, Thomas J; VanBrunt, Michael Pete; Wang, Aijun; Li, Gary; Grabstein, Kenneth

    2015-10-21

    Bioconjugation by copper-catalyzed azide-alkyne cycloaddition (CuAAC) provides a powerful means to produce site-specifically modified proteins. However, the use of a copper catalyst brings about the possible generation of reactive oxygen species that could cause degradation of vulnerable amino acid residues. We investigated whether PEGylation by CuAAC caused any modifications to the therapeutic protein interferon beta-1b, which was produced via global amino acid substitution with azidohomo-alanine at the N-terminus and contains no methionine residues. Using previously reported reaction conditions, LC-MS peptide mapping detected +32 Da and +48 Da oxidation modifications of tryptic peptides 28-33 (LEYCLK) and 137-147 (EYSHCAWTIVR) in the protein post-PEGylation. The oxidative degradation increased with reaction time, whereas reducing the copper concentration slowed the PEGylation rate as well as the oxidation rate. Replacing dithiothreitol (DTT) with any of five different monothiol reducing agents in anaerobic conditions allowed efficient PEGylation in 2-4 h and abrogated oxidative degradation. Free cysteine provided reproducible reaction results as a reducing agent in this system and has been successfully applied to other protein conjugations. Monothiol reducing agents, such as cysteine, may be useful tools as protective reducing agents for CuAAC in some bioconjugation systems. PMID:26439457

  2. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  3. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  4. Towards Advancing Knowledge Translation of AAC Outcomes Research for Children and Youth with Complex Communication Needs.

    PubMed

    Ryan, Stephen E; Shepherd, Tracy; Renzoni, Anne Marie; Anderson, Colleen; Barber, Mary; Kingsnorth, Shauna; Ward, Karen

    2015-06-01

    The production of new knowledge in augmentative and alternative communication (AAC) requires effective processes to leverage the different perspectives of researchers and knowledge users and improve prospects for utilization in clinical settings. This article describes the motivation, planning, process, and outcomes for a novel knowledge translation workshop designed to influence future directions for AAC outcomes research for children with complex communication needs. Invited knowledge users from 20 pediatric AAC clinics and researchers engaged in the collaborative development of research questions using a framework designed for the AAC field. The event yielded recommendations for research and development priorities that extend from the early development of language, communication, and literacy skills in very young children, to novel but unproven strategies that may advance outcomes in transitioning to adulthood. PMID:25860836

  5. AAC and Early Intervention for Children with Cerebral Palsy: Parent Perceptions and Child Risk Factors.

    PubMed

    Smith, Ashlyn L; Hustad, Katherine C

    2015-01-01

    The current study examined parent perceptions of communication, the focus of early intervention goals and strategies, and factors predicting the implementation of augmentative and alternative communication (AAC) for 26 two-year-old children with cerebral palsy. Parents completed a communication questionnaire and provided early intervention plans detailing child speech and language goals. Results indicated that receptive language had the strongest association with parent perceptions of communication. Children who were not talking received a greater number of intervention goals, had a greater variety of goals, and had more AAC goals than children who were emerging and established talkers. Finally, expressive language had the strongest influence on AAC decisions. Results are discussed in terms of the relationship between parent perceptions and language skills, communication as an emphasis in early intervention, AAC intervention decisions, and the importance of receptive language. PMID:26401966

  6. pH-dependent immobilization of proteins on surfaces functionalized by plasma-enhanced chemical vapor deposition of poly(acrylic acid)- and poly(ethylene oxide)-like films.

    PubMed

    Belegrinou, Serena; Mannelli, Ilaria; Lisboa, Patricia; Bretagnol, Frederic; Valsesia, Andrea; Ceccone, Giacomo; Colpo, Pascal; Rauscher, Hubert; Rossi, François

    2008-07-15

    The interaction of the proteins bovine serum albumin (BSA), lysozyme (Lys), lactoferrin (Lf), and fibronectin (Fn) with surfaces of protein-resistant poly(ethylene oxide) (PEO) and protein-adsorbing poly(acrylic acid) (PAA) fabricated by plasma-enhanced chemical vapor deposition has been studied with quartz crystal microbalance with dissipation monitoring (QCM-D). We focus on several parameters which are crucial for protein adsorption, i.e., the isoelectric point (pI) of the proteins, the pH of the solution, and the charge density of the sorbent surfaces, with the zeta-potential as a measure for the latter. The measurements reveal adsorption stages characterized by different segments in the plots of the dissipation vs frequency change. PEO remains protein-repellent for BSA, Lys, and Lf at pH 4-8.5, while weak adsorption of Fn was observed. On PAA, different stages of protein adsorption processes could be distinguished under most experimental conditions. BSA, Lys, Lf, and Fn generally exhibit a rapid initial adsorption phase on PAA, often followed by slower processes. The evaluation of the adsorption kinetics also reveals different adsorption stages, whereas the number of these stages does not always correspond to the structurally different phases as revealed by the D- f plots. The results presented here, together with information obtained in previous studies by other groups on the properties of these proteins and their interaction with surfaces, allow us to develop an adsorption scenario for each of these proteins, which takes into account electrostatic protein-surface and protein-protein interaction, but also the pH-dependent properties of the proteins, such as shape and exposure of specific domains. PMID:18549295

  7. Technology and the use of acrylics for provisional dentine protection.

    PubMed

    Kapusevska, Biljana; Dereban, Nikola; Popovska, Mirjana; Nikolovska, Julijana; Radojkova Nikolovska, Vеrа; Zabokova Bilbilova, Efka; Mijoska, Aneta

    2013-01-01

    Acrylics are compounds polymerized from monomers of acrylic, metacrylic acid or acrylonitrates. The purpose of this paper is to present the technology and use of acrylics for provisional dentine protection in the practice of dental prosthodontics. For this reason, we followed 120 clinical cases from the everyday clinical practice, divided into 4 groups of 30 patients who needed prosthetic reconstruction. The first group included cases in which we applied celluloid crowns for dentine protection, for the second group we used acrylic teeth from a set of teeth for complete dentures; in the third and fourth groups the fabrication was done with the system of an impression matrix and the acrylic resin block technique respectively. In all the examined patients, the gingival index by Silness and Loe and the vitality of the dental pulp were verified clinically, after preparation and 8 days from the placement of the provisional crown. The value for dental sensitivity measured after preparation was 2.59, and 8 days after the placement of the provisional crown it bwas 3.1. From these results we can conclude that after the 8th day from the placement of the provisional crown, there was an adaptation period, characterized by a decrease in the painful sensations. The value of the Silness and Loe gingival index measured after the preparation was 1.34, and 8 days from the placement of the provisional crown was 0.94. The results inclined us to the fact that the provisional acrylic crowns facilitated the reparation of the periodontal tissue. PMID:24566021

  8. Two-dimensional audio watermark for MPEG AAC audio

    NASA Astrophysics Data System (ADS)

    Tachibana, Ryuki

    2004-06-01

    Since digital music is often stored in a compressed file, it is desirable that an audio watermarking method in a content management system handles compressed files. Using an audio watermarking method that directly manipulates compressed files makes it unnecessary to decompress the files before embedding or detection, so more files can be processed per unit time. However, it is difficult to detect a watermark in a compressed file that has been compressed after the file was watermarked. This paper proposes an MPEG Advanced Audio Coding (AAC) bitstream watermarking method using a two-dimensional pseudo-random array. Detection is done by correlating the absolute values of the recovered MDCT coefficients and the pseudo-random array. Since the embedding algorithm uses the same pseudo-random values for two adjacent overlapping frames and the detection algorithm selects the better frame in the two by comparing detected watermark strengths, it is possible to detect a watermark from a compressed file that was compressed after the watermark was embedded in the original uncompressed file. Though the watermark is not detected as clearly in this case, the watermark can still be detected even when the watermark was embedded in a compressed file and the file was then decompressed, trimmed, and compressed again.

  9. Transparent acrylic enamel slide holograms

    NASA Astrophysics Data System (ADS)

    Ponce-Lee, E. L.; Olivares Pérez, A.; Ruiz-Limón, B.; Hernández-Garay, M. P.; Toxqui-López, S.

    2006-02-01

    We present holograms generated in a computer to an acrylic enamel slide (Comex (R)), getting phase holograms. The information in the mask is transferred to the material by temperature gradients generated by rubbing. The refraction index is transformed at each material point by the temperature changes, thus the film is recorded and developed by itself. this material can be used for soft lithography.

  10. Mixing It Up with Acrylics.

    ERIC Educational Resources Information Center

    Laird, Shirley

    1999-01-01

    Presents an art activity for fifth-grade students in which they learn about basic shapes and what happens when shapes overlap, draw seven overlapping geometric shapes, review the use of acrylic paint and mixing colors, and finally paint with primary colors. (CMK)

  11. Fluorescent Boronic Acid Polymer Grafted on Silica Particles for Affinity Separation of Saccharides

    PubMed Central

    2014-01-01

    Boronic acid affinity gels are important for effective separation of biological active cis-diols, and are finding applications both in biotech industry and in biomedical research areas. To increase the efficacy of boronate affinity separation, it is interesting to introduce repeating boronic acid units in flexible polymer chains attached on solid materials. In this work, we synthesize polymer brushes containing boronic acid repeating units on silica gels using surface-initiated atom transfer radical polymerization (ATRP). A fluorescent boronic acid monomer is first prepared from an azide-tagged fluorogenic boronic acid and an alkyne-containing acrylate by Cu(I)-catalyzed 1,3-dipolar cycloaddition reaction (the CuAAC click chemistry). The boronic acid monomer is then grafted to the surface of silica gel modified with an ATRP initiator. The obtained composite material contains boronic acid polymer brushes on surface and shows favorable saccharide binding capability under physiological pH conditions, and displays interesting fluorescence intensity change upon binding fructose and glucose. In addition to saccharide binding, the flexible polymer brushes on silica also enable fast separation of a model glycoprotein based on selective boronate affinity interaction. The synthetic approach and the composite functional material developed in this work should open new opportunities for high efficiency detection, separation, and analysis of not only simple saccharides, but also glycopeptides and large glycoproteins. PMID:24444898

  12. Fluorescent boronic acid polymer grafted on silica particles for affinity separation of saccharides.

    PubMed

    Xu, Zhifeng; Uddin, Khan Mohammad Ahsan; Kamra, Tripta; Schnadt, Joachim; Ye, Lei

    2014-02-12

    Boronic acid affinity gels are important for effective separation of biological active cis-diols, and are finding applications both in biotech industry and in biomedical research areas. To increase the efficacy of boronate affinity separation, it is interesting to introduce repeating boronic acid units in flexible polymer chains attached on solid materials. In this work, we synthesize polymer brushes containing boronic acid repeating units on silica gels using surface-initiated atom transfer radical polymerization (ATRP). A fluorescent boronic acid monomer is first prepared from an azide-tagged fluorogenic boronic acid and an alkyne-containing acrylate by Cu(I)-catalyzed 1,3-dipolar cycloaddition reaction (the CuAAC click chemistry). The boronic acid monomer is then grafted to the surface of silica gel modified with an ATRP initiator. The obtained composite material contains boronic acid polymer brushes on surface and shows favorable saccharide binding capability under physiological pH conditions, and displays interesting fluorescence intensity change upon binding fructose and glucose. In addition to saccharide binding, the flexible polymer brushes on silica also enable fast separation of a model glycoprotein based on selective boronate affinity interaction. The synthetic approach and the composite functional material developed in this work should open new opportunities for high efficiency detection, separation, and analysis of not only simple saccharides, but also glycopeptides and large glycoproteins. PMID:24444898

  13. Toward pH-responsive coating materials--high-throughput study of (meth)acrylic copolymers.

    PubMed

    Krieg, Andreas; Arici, Elif; Windhab, Norbert; Schattka, Jan Hendrik; Schubert, Stephanie; Schubert, Ulrich S

    2014-08-11

    The release behavior of a model compound (β-naphthol orange) encapsulated in (meth)acrylate-based statistical copolymers under different environmental conditions was investigated. From monomers of varying polarity (methyl acrylate, ethyl acrylate, tert-butyl acrylate, 2-ethylhexyl methacrylate, and benzyl methacrylate) in combination with methacrylic acid, five polymer series were synthesized by free radical polymerization. The pH-dependent release kinetics were investigated via UV-vis spectroscopy at pH 1.2 and 6.8, simulating physiological conditions in the stomach and intestines. Furthermore, the influence of different ethanol contents (0 and 40 vol %) in the acidic medium was investigated. The whole approach was designed to meet the requirements of a high-throughput experimentation workflow. PMID:24964068

  14. Is Awesome Really Awesome? How the Inclusion of Informal Terms on an AAC Device Influences Children's Attitudes toward Peers Who Use AAC

    ERIC Educational Resources Information Center

    Beck, Ann R.; Bock, Stacey; Thompson, James R.; Bowman, Linda; Robbins, Stacey

    2006-01-01

    Two videotapes were created of a child communicating with a voice output augmentative and alternative communication (AAC) device. In one the child communicated using formal English only and in the other the child communicated using formal English and age appropriate informal terms. Children in grades 4 and 5 viewed either the formal English only…

  15. Electrochemical characterization of aminated acrylic conducting polymer

    NASA Astrophysics Data System (ADS)

    Rashid, Norma Mohammad; Heng, Lee Yook; Ling, Tan Ling

    2015-09-01

    New attempt has been made to synthesize aminated acrylic conducting polymer (AACP) using precursor of phenylvinylsulfoxide (PVS). The process was conducted via the integration of microemulsion and photopolymerization techniques. It has been utilized for covalent immobilization of amino groups by the adding of N-achryiloxisuccinimide (NAS). Thermal eliminating of benzene sulfenic acids from PVS has been done at 250 °C to form electroactive polyacetylene (PA) segment. Characterization of AACP has been conducted using fourier transform infrared (FTIR), scanning electron microscopy (SEM) and linear sweep cyclic voltammetry (CV). A range of 0.3-1.25μm particle size obtained from SEM characterization. A quasi-reversible system performed as shown in electrochemical study.

  16. Electrochemical characterization of aminated acrylic conducting polymer

    SciTech Connect

    Rashid, Norma Mohammad; Heng, Lee Yook; Ling, Tan Ling

    2015-09-25

    New attempt has been made to synthesize aminated acrylic conducting polymer (AACP) using precursor of phenylvinylsulfoxide (PVS). The process was conducted via the integration of microemulsion and photopolymerization techniques. It has been utilized for covalent immobilization of amino groups by the adding of N-achryiloxisuccinimide (NAS). Thermal eliminating of benzene sulfenic acids from PVS has been done at 250 °C to form electroactive polyacetylene (PA) segment. Characterization of AACP has been conducted using fourier transform infrared (FTIR), scanning electron microscopy (SEM) and linear sweep cyclic voltammetry (CV). A range of 0.3-1.25μm particle size obtained from SEM characterization. A quasi-reversible system performed as shown in electrochemical study.

  17. Acrylic esters in radiation polymerization

    SciTech Connect

    Fomina, N.V.; Khoromskaya, V.A.; Shiryaeva, G.V.

    1988-03-01

    The radiation behavior of (meth)acrylic esters of varying structure was studied. It was shown that in radiation polymerization, in contrast to thermal polymerization, the structure of the ester part can significantly affect the reaction rate and capacity for polymerization in the presence of oxygen. The experimental data are explained from the point of view of consideration of nonvalence effects of the substitutent on the reactivity of the double bond.

  18. AAC to Support Conversation in Persons with Moderate Alzheimer’s Disease

    PubMed Central

    FRIED-OKEN, MELANIE; ROWLAND, CHARITY; DANIELS, DARLENE; DIXON, MAYLING; FULLER, BRET; MILLS, CAROLYN; NOETHE, GLORY; SMALL, JEON; STILL, KEVIN; OKEN, BARRY

    2013-01-01

    Even though we know that external memory aids support communication in Alzheimer’s disease, the components of the communication aids for individuals with Alzheimer’s disease have not been studied systematically. The goal of these two pilot experiments was to examine differences in conversational performance of adults with Alzheimer’s disease related to the presence and absence of an aid, the type of symbol embedded in the aid, and the presence or absence of voice output. In Experiment 1, 30 adults with moderate-to-severe Alzheimer’s disease participated in 10-min conversations with and without personalized AAC boards. There was no effect of AAC, regardless of symbol type, and a deleterious effect of voice output. In Experiment 2, modified spaced-retrieval training preceded conversations, standardized prompts were presented, and semantically-based dependent variables were examined. For the 11 participants in the second experiment, there was a significant effect of AAC, showing that the presence of AAC was associated with greater use of targeted words during personal conversations. We discuss new information about the contribution of AAC for persons with Alzheimer’s disease, and demonstrate how the applied research process evolves over the course of a long-term commitment to a scientific investigation. PMID:23256854

  19. Detection of aac(6')-Ib-cr in avian pathogenic Escherichia coli isolates in Japan.

    PubMed

    Kawanishi, Michiko; Ozawa, Manao; Hiki, Mototaka; Abo, Hitoshi; Kojima, Akemi; Asai, Tetsuo

    2013-11-01

    We investigated the prevalence of plasmid-mediated quinolone resistance (PMQR) genes in avian pathogenic Escherichia coli (APEC) strains in Japan. A total of 117 APEC strains collected between 2004 and 2007 were examined for PMQR genes (qnrA, qnrB, qnrC, qnrD, qnrS, aac(6')-Ib-cr, qepA and oqxAB) by polymerase chain reaction. None of the APEC strains carried qnrA, qnrB, qnrC, qnrD, qnrS, qepA or oqxAB, but one of the isolates was identified as an AAC (6')-Ib-cr producer. Phylogenetic grouping, multi-locus sequence typing and serotyping showed that this isolate belonged to phylogenetic group A, sequence type 167 and untypable serogroup. To our knowledge, this is the first report of the aac (6')-Ib-cr gene in bacteria from food-producing animals in Japan. PMID:23856759

  20. Poly(amide-graft-acrylate) interfacial compounds

    NASA Astrophysics Data System (ADS)

    Zamora, Michael Perez

    Graft copolymers with segments of dissimilar chemistries have been shown to be useful in a variety of applications as surfactants, compatibilizers, impact modifiers, and surface modifiers. The most common route to well defined graft copolymers is through the use of macromonomers, polymers containing a reactive functionality and thus capable of further polymerization. However, the majority of the studies thus far have focused on the synthesis of macromonomers capable of reacting with vinyl monomers to form graft copolymers. This study focused on the synthesis of macromonomers capable of participating in condensation polymerizations. A chain transfer functionalization method was utilized. Cysteine was evaluated as a chain transfer agent for the synthesis of amino acid functionalized poly(acrylate) and poly(methacrylate) macromonomers. Low molar mass, functionalized macromonomers were produced. These macromonomers were proven to be capable of reacting with amide precursors to form poly(amide-g-acrylate) graft copolymers. Macromonomers and graft copolymers were characterized by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) spectroscopy, elemental analysis (EA), inductively coupled plasma (ICP), and differential scanning calorimetry (DSC). The second part of this research involved poly(dimethacrylate) dental restorative materials. Volumetric shrinkage during the cure of these resins results in a poor interface between the resin and the remaining tooth structure, limiting the lifetime of these materials. Cyclic anhydrides were incorporated into common monomer compositions used in dental applications. Volume expansion from the ring opening hydrolysis of these anhydrides was shown to be feasible. The modified dental resins were characterized by swelling, extraction and ultraviolet spectroscopy (UV), and density measurements. Linear poLymers designed to model the crosslinked dental resins were

  1. Wavelength Shifters and Interactions of EDTA with Acrylic & LAB

    NASA Astrophysics Data System (ADS)

    Mohan, Yuvraj; SNO+ Collaboration

    2014-09-01

    The SNO + experiment, an upgrade to the Sudbury Neutrino Observatory, will use linear alkyl-benzene (LAB) liquid scintillator to probe new physics, including 0 νββ decay. Event detection efficiency is heavily affected by radioactive backgrounds, two sources being Rn-222 and Po-210 daughters, some of which has become embedded in the SNO + acrylic vessel after years underground. The leading candidate for polonium leaching is Ethylenediaminetetraacetic acid (EDTA). Before deployment on-site, EDTA's effects on the mechanical integrity of acrylic must be determined. It also must not be soluble in LAB or must be removed before scintillator fill of the vessel, as its presence would result in reduced light yield due to scattering. It was found that EDTA had negligible effects on the Young's Modulus of acrylic. EDTA is also slightly soluble in LAB, but can be completely removed by rinsing with water. Additionally, the study of the light yield and alpha/beta timing profiles of two wavelength shifters - bisMSB and perylene - is critical to determining which should be added to the 0 νββ isotope (tellurium) LAB cocktail. Small-scale results hint that perylene might be better, but this is being confirmed with larger-scale tests. The SNO + experiment, an upgrade to the Sudbury Neutrino Observatory, will use linear alkyl-benzene (LAB) liquid scintillator to probe new physics, including 0 νββ decay. Event detection efficiency is heavily affected by radioactive backgrounds, two sources being Rn-222 and Po-210 daughters, some of which has become embedded in the SNO + acrylic vessel after years underground. The leading candidate for polonium leaching is Ethylenediaminetetraacetic acid (EDTA). Before deployment on-site, EDTA's effects on the mechanical integrity of acrylic must be determined. It also must not be soluble in LAB or must be removed before scintillator fill of the vessel, as its presence would result in reduced light yield due to scattering. It was found that EDTA

  2. Support for AAC Use in Preschool, and Growth in Language Skills, for Young Children with Developmental Disabilities

    PubMed Central

    BARKER, R. MICHAEL; AKABA, SANAE; BRADY, NANCY C.; THIEMANN-BOURQUE, KATHY

    2014-01-01

    Little is known about how AAC use in preschool may impact language development for children with complex communication needs (e.g., children with autism, cerebral palsy, Down syndrome, and other developmental disabilities). We developed two surveys (a) to describe children’s use of AAC in preschool classrooms, as well as the use of prompts and question asking, and augmented input by their communication partners; and (b) to describe teachers’ experience, training, and perceived support in providing AAC. We then examined the relationship between children’s experience of AAC, including the use of prompts, question asking, and augmented input by their partners, and the growth of receptive and expressive language for 71 children with developmental disabilities over a two-year period. The use of AAC by peers to provide augmented input was associated with stronger language growth; the use of prompting and question asking by teachers was associated with weaker language growth. Teachers reported that they received little training regarding ways to support a child’s use of AAC. Results suggest the need for further research on promoting AAC use at the preschool level, including research to promote peer interactions for AAC users. PMID:24229337

  3. Surface modification of nanoparticles for radiation curable acrylate clear coatings

    NASA Astrophysics Data System (ADS)

    Bauer, F.; Gläsel, H.-J.; Hartmann, E.; Bilz, E.; Mehnert, R.

    2003-08-01

    To obtain transparent, scratch and abrasion resistant coatings a high content of nanosized silica and alumina filler was embedded in radiation-curable acrylate formulations by acid catalyzed silylation using trialkoxysilanes. 29SiMAS NMR and MALDI-TOF mass spectrometry were employed to elucidate the structure of the surface-grafted methacryloxypropyl-, vinyl- and n-propyl-trimethoxysilane. In accordance with NMR findings, MALDI-TOF MS showed highly condensed oligomeric siloxanes of more than 20 monomeric silane units. A ladder-like structure of bound polysiloxanes is proposed rather than a simplified picture of tridentate silane bonding. Hence, silane coupling agents do not only modify the chemical nature of the filler surface but also strongly effect the rheological properties of the acrylate nanodispersions.

  4. Chronic pulmonary dysfunction following acute inhalation of butyl acrylate.

    PubMed

    Bhardwaj, Ravindra; Ducatman, Alan; Finkel, Mitchell S; Petsonk, Edward; Hunt, Janet; Beto, Robert J

    2012-01-01

    Butyl Acrylate (BA) (2-propionic acid; CH2 = CHCOOC4H9) is a colorless liquid commonly used in impregnation agents and adhesives. Dermal contact with BA has previously been reported to cause moderate skin irritation with skin sensitizing potential in humans. Health effects of inhalation of BA have not been previously reported. Accordingly, we document the health conditions of a bystander, first responder and landfill worker exposed to butyl acrylate (BA) released to the atmosphere following a collision and roadside spill in October 1998. Retrospective data were collected via chart review and analyzed for exposure, symptoms, physical findings and radiological, laboratory and spirometry results over a ten-year period. All three patients had similar respiratory symptoms including a dramatic hacking cough and dyspnea. Findings included abnormal pulmonary function tests and breath sounds. These data underscore the potential hazards of BA inhalational exposure and the need to wear additional protective equipment. PMID:23472539

  5. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...) The acrylate ester copolymer is a fully polymerized copolymer of ethyl acrylate, methyl methacrylate... emulsion defoamer. Disodium hydrogen phosphate Do. Formaldehyde Glyceryl monostearate Methyl...

  6. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...) The acrylate ester copolymer is a fully polymerized copolymer of ethyl acrylate, methyl methacrylate... emulsion defoamer. Disodium hydrogen phosphate Do. Formaldehyde Glyceryl monostearate Methyl...

  7. 40 CFR 721.405 - Polyether acrylate.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.405 Polyether acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polyether acrylate (PMN P-95-666) is subject...

  8. 40 CFR 721.405 - Polyether acrylate.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.405 Polyether acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polyether acrylate (PMN P-95-666) is subject...

  9. Use and Acceptance of AAC Systems by Children with Angelman Syndrome

    ERIC Educational Resources Information Center

    Calculator, Stephen N.

    2013-01-01

    Background: This investigation of children with Angelman syndrome (AS) examined reported uses of electronic augmentative and alternative communication (AAC) devices (i.e. VOCAs), including speech generating devices, in relation to other aided and unaided methods of communication. Materials and Method: A total of 122 parents of children with AS,…

  10. Women in Educational Technology: Content Analysis of AACE Journals 2004-2007

    ERIC Educational Resources Information Center

    Kennedy, Kathryn; Liu, Feng; Dawson, Kara; Cavanaugh, Cathy

    2009-01-01

    Professional qualifications for men and women are equivalent across disciplines, however, women tend to be underrepresented in technology-related fields. The purpose of this study is to analyze the content of seven journals published by the Association for the Advancement of Computing in Education (AACE) to explore women's publications in…

  11. AAC Camp as an Alternative School-Based Service Delivery Model: A Retrospective Survey

    ERIC Educational Resources Information Center

    Dodd, Janet L.; Hagge, Darla K.

    2014-01-01

    School-based speech-language pathologists are obligated to apply evidence-based practice and document progress of their students' response to intervention in compliance with federal law. The purpose of this preliminary study was to explore the effects of an augmentative and alternative communication (AAC)-based intervention provided in a camp…

  12. Effects of Communication Partner Instruction on the Communication of Individuals using AAC: A Meta-Analysis.

    PubMed

    Kent-Walsh, Jennifer; Murza, Kimberly A; Malani, Melissa D; Binger, Cathy

    2015-01-01

    The purpose of this study was to conduct a systematic review and meta-analysis of the augmentative and alternative communication (AAC) partner instruction intervention literature to determine (a) the overall effects of partner interventions on the communication of individuals using AAC, and (b) any possible moderating variables relating to participant, intervention, or outcome characteristics. Seventeen single-case experimental design studies (53 participants) met the inclusion criteria and were advanced to the full coding and analysis phase of the investigation. Descriptive analyses and effect size estimations using the Improvement Rate Difference (IRD) metric were conducted. Overall, communication partner interventions were found to be highly effective across a range of participants using AAC, intervention approaches, and outcome measure characteristics, with more evidence available for participants less than 12 years of age, most of whom had a diagnosis of autism spectrum disorder or intellectual/developmental disability. Aided AAC modeling, expectant delay, and open-ended question asking were the most frequently targeted communication partner interaction skills. Providing a descriptive overview, instructor modeling, guided practice, and role plays were the most frequently incorporated communication partner intervention activities within the included studies. PMID:26059542

  13. The Role of Faculty in the Transformation of AAC&U: A Personal Essay

    ERIC Educational Resources Information Center

    Gaff, Jerry

    2015-01-01

    During the first sixty years after the founding of the Association of American Colleges (AAC) in 1915, it was an association of institutions and their presidents; faculty members were conspicuous by their absence. Jerry Gaff is senior scholar at the Association of American Colleges and Universities. He arrived in 1975 to direct a project on…

  14. Insights into Communication Intervention and AAC in South India: A Mixed-Methods Study

    ERIC Educational Resources Information Center

    Srinivasan, Saranya; Mathew, Samuel N.; Lloyd, Lyle L.

    2011-01-01

    This study investigated current trends in communication intervention and augmentative and alternative communication (AAC) in southern India through a mixed-methods design. Study participants (N = 18) were special educators, speech-language pathologists, and behavior therapists. Responses from the questionnaire were quantitatively analyzed.…

  15. The Development and Utilization of a Scale to Measure Adolescents' Attitudes toward Peers Who Use Augmentative and Alternative Communication (AAC) Devices

    ERIC Educational Resources Information Center

    Beck, Ann R.; Thompson, James R.; Kosuwan, Kullaya; Prochnow, Jessica M.

    2010-01-01

    Purpose: Study 1 developed the Assessment of Attitudes Toward Augmentative and Alternative Communication-2 (AATAAC-2) to assess adolescents' attitudes toward peers who use AAC. Study 2 used the AATAAC-2 to examine influences of familiarity with people with disabilities; type of AAC device; and various combinations of gender of rater, AAC user, and…

  16. The AACES field experiments: SMOS calibration and validation across the Murrumbidgee River catchment

    NASA Astrophysics Data System (ADS)

    Peischl, S.; Walker, J. P.; Rüdiger, C.; Ye, N.; Kerr, Y. H.; Kim, E.; Bandara, R.; Allahmoradi, M.

    2012-03-01

    Following the launch of the European Space Agency's Soil Moisture and Ocean Salinity (SMOS) mission on 2 November 2009, SMOS products need to be rigorously validated at the satellite's approximately 45 km scale, and disaggregation techniques for maps with finer resolutions tested. The Australian Airborne Cal/val Experiments for SMOS (AACES) provide the basis for one of the most comprehensive assessments of SMOS data world-wide by covering a range of topographic, climatic and land surface variability within an approximately 500 × 100 km2 study area, located in South-East Australia. The AACES calibration and validation activities consisted of two extensive field experiments which were undertaken across the Murrumbidgee River catchment during the Australian summer and winter season of 2010, respectively. The data sets include airborne L-band brightness temperature, thermal infrared and multi-spectral observations at 1 km resolution, as well as extensive ground measurements of near-surface soil moisture and ancillary data, such as soil temperature, soil texture, surface roughness, vegetation water content, dew amount, leaf area index and spectral characteristics of the vegetation. This paper explains the design and data collection strategy of the airborne and ground component of the two AACES campaigns and presents a preliminary analysis of the field measurements including the application and performance of the SMOS core retrieval model on the diverse land surface conditions captured by the experiments. The data described in this paper are publicly available from the website: aaces" target="_blank">http://www.moisturemap.monash.edu.au/aaces.

  17. The AACES field experiments: SMOS calibration and validation across the Murrumbidgee River catchment

    NASA Astrophysics Data System (ADS)

    Peischl, S.; Walker, J. P.; Rüdiger, C.; Ye, N.; Kerr, Y. H.; Kim, E.; Bandara, R.; Allahmoradi, M.

    2012-06-01

    Following the launch of the European Space Agency's Soil Moisture and Ocean Salinity (SMOS) mission on 2 November 2009, SMOS soil moisture products need to be rigorously validated at the satellite's approximately 45 km scale and disaggregation techniques for producing maps with finer resolutions tested. The Australian Airborne Cal/val Experiments for SMOS (AACES) provide the basis for one of the most comprehensive assessments of SMOS data world-wide by covering a range of topographic, climatic and land surface variability within an approximately 500 × 100 km2 study area, located in South-East Australia. The AACES calibration and validation activities consisted of two extensive field experiments which were undertaken across the Murrumbidgee River catchment during the Australian summer and winter season of 2010, respectively. The datasets include airborne L-band brightness temperature, thermal infrared and multi-spectral observations at 1 km resolution, as well as extensive ground measurements of near-surface soil moisture and ancillary data, such as soil temperature, soil texture, surface roughness, vegetation water content, dew amount, leaf area index and spectral characteristics of the vegetation. This paper explains the design and data collection strategy of the airborne and ground component of the two AACES campaigns and presents a preliminary analysis of the field measurements including the application and performance of the SMOS core retrieval model on the diverse land surface conditions captured by the experiments. The data described in this paper are publicly available from the website: aaces"target="_blank">http://www.moisturemap.monash.edu.au/aaces.

  18. Radiopurity measurement of acrylic for DEAP-3600

    SciTech Connect

    Nantais, C. M.; Boulay, M. G.; Cleveland, B. T.

    2013-08-08

    The spherical acrylic vessel that contains the liquid argon target is the most critical detector component in the DEAP-3600 dark matter experiment. Alpha decays near the inner surface of the acrylic vessel are one of the main sources of background in the detector. A fraction of the alpha energy, or the recoiling nucleus from the alpha decay, could misreconstruct in the fiducial volume and result in a false candidate dark matter event. Acrylic has low levels of inherent contamination from {sup 238}U and {sup 232}Th. Another background of particular concern is diffusion of {sup 222}Rn during manufacturing, leading to {sup 210}Pb contamination. The maximum acceptable concentrations in the DEAP-3600 acrylic vessel are ppt levels of {sup 238}U and {sup 232}Th equivalent, and 10{sup −8} ppt {sup 210}Pb. The impurities in the bulk acrylic will be measured by vaporizing a large quantity of acrylic and counting the concentrated residue with ultra-low background HPGe detectors and a low background alpha spectrometer. An overview of the acrylic assay technique is presented.

  19. Occupational respiratory disease caused by acrylates.

    PubMed

    Savonius, B; Keskinen, H; Tuppurainen, M; Kanerva, L

    1993-05-01

    Acrylates are compounds used in a variety of industrial fields and their use is increasing. They have many features which make them superior to formerly used chemicals, regarding both their industrial use and their possible health effects. Contact sensitization is, however, one of their well known adverse health effects but they may also cause respiratory symptoms. We report on 18 cases of respiratory disease, mainly asthma, caused by different acrylates, 10 cases caused by cyanoacrylates, four by methacrylates and two cases by other acrylates. PMID:8334539

  20. Overview of the Recent Operation of the AAC and LEAR for the Low-energy Antiproton Physics Programme

    NASA Astrophysics Data System (ADS)

    Maury, S.; Baird, S.; Boillot, J.; Caspers, F.; Chanel, M.; Chohan, V.; Eriksson, T.; Ley, R.; Metzger, C.; Möhl, D.; Mulder, H.; Pedersen, F.; Tranquille, G.

    1997-05-01

    This paper reviews the recent performances of the AAC and LEAR. Activities on the AAC include the successful exploitation of a magnetic horn as an antiproton collector lens and an energy-saving mode of operation which has been possible since 1992 when LEAR became the only client of the AAC. LEAR has worked in virtually its full momentum range between 100 MeV/c and 2 GeV/c, with performances (intensities, ejection modes and spill length) often exceeding the design specifications. Improvements are described which contributed to the quality of the beam delivered to the experiments. The reliability and the availability of the antiproton machines is also discussed.

  1. QnrS1- and Aac(6')-Ib-cr-Producing Escherichia coli among Isolates from Animals of Different Sources: Susceptibility and Genomic Characterization.

    PubMed

    Jones-Dias, Daniela; Manageiro, Vera; Graça, Rafael; Sampaio, Daniel A; Albuquerque, Teresa; Themudo, Patrícia; Vieira, Luís; Ferreira, Eugénia; Clemente, Lurdes; Caniça, Manuela

    2016-01-01

    Salmonella enterica and Escherichia coli can inhabit humans and animals from multiple origins. These bacteria are often associated with gastroenteritis in animals, being a frequent cause of resistant zoonotic infections. In fact, bacteria from animals can be transmitted to humans through the food chain and direct contact. In this study, we aimed to assess the antibiotic susceptibility of a collection of S. enterica and E. coli recovered from animals of different sources, performing a genomic comparison of the plasmid-mediated quinolone resistance (PMQR)-producing isolates detected. Antibiotic susceptibility testing revealed a high number of non-wild-type isolates for fluoroquinolones among S. enterica recovered from poultry isolates. In turn, the frequency of non-wild-type E. coli to nalidixic acid and ciprofloxacin was higher in food-producing animals than in companion or zoo animals. Globally, we detected two qnrS1 and two aac(6')-Ib-cr in E. coli isolates recovered from animals of different origins. The genomic characterization of QnrS1-producing E. coli showed high genomic similarity (O86:H12 and ST2297), although they have been recovered from a healthy turtle dove from a Zoo Park, and from a dog showing symptoms of infection. The qnrS1 gene was encoded in a IncN plasmid, also carrying bla TEM-1-containing Tn3. Isolates harboring aac(6')-Ib-cr were detected in two captive bottlenose dolphins, within a time span of two years. The additional antibiotic resistance genes of the two aac(6')-Ib-cr-positive isolates (bla OXA-1, bla TEM-1,bla CTX-M-15, catB3, aac(3)-IIa, and tetA) were enclosed in IncFIA plasmids that differed in a single transposase and 60 single nucleotide variants. The isolates could be assigned to the same genetic sublineage-ST131 fimH30-Rx (O25:H4), confirming clonal spread. PMQR-producing isolates were associated with symptomatic and asymptomatic hosts, which highlight the aptitude of E. coli to act as silent vehicles, allowing the accumulation

  2. QnrS1- and Aac(6′)-Ib-cr-Producing Escherichia coli among Isolates from Animals of Different Sources: Susceptibility and Genomic Characterization

    PubMed Central

    Jones-Dias, Daniela; Manageiro, Vera; Graça, Rafael; Sampaio, Daniel A.; Albuquerque, Teresa; Themudo, Patrícia; Vieira, Luís; Ferreira, Eugénia; Clemente, Lurdes; Caniça, Manuela

    2016-01-01

    Salmonella enterica and Escherichia coli can inhabit humans and animals from multiple origins. These bacteria are often associated with gastroenteritis in animals, being a frequent cause of resistant zoonotic infections. In fact, bacteria from animals can be transmitted to humans through the food chain and direct contact. In this study, we aimed to assess the antibiotic susceptibility of a collection of S. enterica and E. coli recovered from animals of different sources, performing a genomic comparison of the plasmid-mediated quinolone resistance (PMQR)-producing isolates detected. Antibiotic susceptibility testing revealed a high number of non-wild-type isolates for fluoroquinolones among S. enterica recovered from poultry isolates. In turn, the frequency of non-wild-type E. coli to nalidixic acid and ciprofloxacin was higher in food-producing animals than in companion or zoo animals. Globally, we detected two qnrS1 and two aac(6′)-Ib-cr in E. coli isolates recovered from animals of different origins. The genomic characterization of QnrS1-producing E. coli showed high genomic similarity (O86:H12 and ST2297), although they have been recovered from a healthy turtle dove from a Zoo Park, and from a dog showing symptoms of infection. The qnrS1 gene was encoded in a IncN plasmid, also carrying blaTEM−1−containing Tn3. Isolates harboring aac(6′)-Ib-cr were detected in two captive bottlenose dolphins, within a time span of two years. The additional antibiotic resistance genes of the two aac(6′)-Ib-cr-positive isolates (blaOXA−1, blaTEM−1,blaCTX−M−15, catB3, aac(3)-IIa, and tetA) were enclosed in IncFIA plasmids that differed in a single transposase and 60 single nucleotide variants. The isolates could be assigned to the same genetic sublineage—ST131 fimH30-Rx (O25:H4), confirming clonal spread. PMQR-producing isolates were associated with symptomatic and asymptomatic hosts, which highlight the aptitude of E. coli to act as silent vehicles, allowing

  3. Optimization of a Novel Binding Motif to (E)-3-(3,5-Difluoro-4-((1R,3R)-2-(2-fluoro-2-methylpropyl)-3-methyl-2,3,4,9-tetrahydro-1H-pyrido[3,4-b]indol-1-yl)phenyl)acrylic Acid (AZD9496), a Potent and Orally Bioavailable Selective Estrogen Receptor Downregulator and Antagonist.

    PubMed

    De Savi, Chris; Bradbury, Robert H; Rabow, Alfred A; Norman, Richard A; de Almeida, Camila; Andrews, David M; Ballard, Peter; Buttar, David; Callis, Rowena J; Currie, Gordon S; Curwen, Jon O; Davies, Chris D; Donald, Craig S; Feron, Lyman J L; Gingell, Helen; Glossop, Steven C; Hayter, Barry R; Hussain, Syeed; Karoutchi, Galith; Lamont, Scott G; MacFaul, Philip; Moss, Thomas A; Pearson, Stuart E; Tonge, Michael; Walker, Graeme E; Weir, Hazel M; Wilson, Zena

    2015-10-22

    The discovery of an orally bioavailable selective estrogen receptor downregulator (SERD) with equivalent potency and preclinical pharmacology to the intramuscular SERD fulvestrant is described. A directed screen identified the 1-aryl-2,3,4,9-tetrahydro-1H-pyrido[3,4-b]indole motif as a novel, druglike ER ligand. Aided by crystal structures of novel ligands bound to an ER construct, medicinal chemistry iterations led to (E)-3-(3,5-difluoro-4-((1R,3R)-2-(2-fluoro-2-methylpropyl)-3-methyl-2,3,4,9-tetrahydro-1H-pyrido[3,4-b]indol-1-yl)phenyl)acrylic acid (30b, AZD9496), a clinical candidate with high oral bioavailability across preclinical species that is currently being evaluated in phase I clinical trials for the treatment of advanced estrogen receptor (ER) positive breast cancer. PMID:26407012

  4. UV curing of nanoparticle reinforced acrylates

    NASA Astrophysics Data System (ADS)

    Bauer, F.; Flyunt, R.; Czihal, K.; Ernst, H.; Naumov, S.; Buchmeiser, M. R.

    2007-12-01

    To improve the surface hardness of radiation cured acrylate coatings, both silica nanoparticles and alumina particles with a few microns in size have been embedded into acrylate formulations. Regular mixing of nanoparticles into acrylate formulations, however, leads to highly viscous solutions inappropriate for coating procedures. The incompatibility of inorganic fillers and organic polymers can be avoided by surface modification of nanoparticles using trialkoxysilanes, which provide an interface between the two dissimilar materials. Nanoparticles modified by methacryloxypropyltrimethoxysilane (MEMO) and vinyltrimethoxysilane (VTMO), both having polymerisation-active groups, may be crosslinked with the acrylate resin. UV curing of the nanocomposites revealed an unexpected lower reactivity of the vinyl groups of VTMO modified silica compared to MEMO grafted on silica. For VTMO modification, DFT calculations showed a decrease of Mulliken atomic charge for the olefinic carbons pointing to a lower reactivity. For UV cured nano/microhybrid composites, a significant improvement of abrasion resistance was obtained.

  5. Gel time of calcium acrylate grouting material.

    PubMed

    Han, Tong-Chun

    2004-08-01

    Calcium acrylate is a polymerized grout, and can polymerize in an aqueous solution. The polymerization reaction utilizes ammonium persulfate as a catalyst and sodium thiosulfate as the activator. Based on the theory of reaction kinetics, this study on the relation between gel time and concentration of activator and catalyst showed that gel time of calcium acrylate is inversely proportional to activator and catalyst concentration. A formula of gel time is proposed, and an example is provided to verify the proposed formula. PMID:15236477

  6. AAC and RTI: building classroom-based strategies for every child in the classroom.

    PubMed

    Grether, Sandra M; Sickman, Linda Sue

    2008-05-01

    Educators were previously encouraged to use IQ-achievement discrepancy to identify children with learning disabilities. The Individuals with Disabilities Education Improvement Act promotes an alternative method, response to intervention, or RTI, not only to identify these children but also to provide early intervention to all children at risk for school failure. Children with complex communication needs who use augmentative and alternative communication (AAC) are at risk for failure in the classroom and can benefit from the educational supports provided through RTI. This article discusses the levels of support provided by RTI, the speech-language pathologist's role in RTI, and strategies and supports for achieving academic success for children who use AAC. PMID:18645917

  7. 17 Ways to Say Yes: Toward Nuanced Tone of Voice in AAC and Speech Technology

    PubMed Central

    Pullin, Graham; Hennig, Shannon

    2015-01-01

    Abstract People with complex communication needs who use speech-generating devices have very little expressive control over their tone of voice. Despite its importance in human interaction, the issue of tone of voice remains all but absent from AAC research and development however. In this paper, we describe three interdisciplinary projects, past, present and future: The critical design collection Six Speaking Chairs has provoked deeper discussion and inspired a social model of tone of voice; the speculative concept Speech Hedge illustrates challenges and opportunities in designing more expressive user interfaces; the pilot project Tonetable could enable participatory research and seed a research network around tone of voice. We speculate that more radical interactions might expand frontiers of AAC and disrupt speech technology as a whole. PMID:25965913

  8. Evaluating the Impact of AAC Interventions in Reducing Hospitalization-related Stress: Challenges and Possibilities.

    PubMed

    Thunberg, Gunilla; Törnhage, Carl-Johan; Nilsson, Stefan

    2016-06-01

    Hospitalization is a stressful context for all children and their families, but especially for children with communication difficulties. Effective communication using augmentative and alternative communication (AAC) strategies can play a critical role in preparing and supporting everyone involved in such situations to have discussions that minimize insecurity, allow children to express their concerns, and so decrease negative stress and anxiety. However, there is a critical need to identify robust and reliable ways of evaluating the effectiveness of interventions that seek to achieve this aim. This research note illustrates some of the challenges and problems that require attention and suggests possible new research tools, for example, the use of physiological measures. The evaluation of an AAC intervention on a day surgery ward is described and used to illustrate one potential physiological measure for evaluating the impact of an intervention. PMID:27116244

  9. CuAAC click reactions for the design of multifunctional luminescent ruthenium complexes.

    PubMed

    Zabarska, Natalia; Stumper, Anne; Rau, Sven

    2016-02-01

    CuAAC (Cu(i) catalyzed azide-alkyne cycloaddition) click chemistry has emerged as a versatile tool in the development of photoactive ruthenium complexes with multilateral potential applicability. In this contribution we discuss possible synthetic approaches towards CuAAC reactions with ruthenium(ii) polypyridine complexes and their differences with respect to possible applications. We focus on two main application possibilities of the click-coupled ruthenium assemblies. New results within the development of ruthenium based photosensitizers for the field of renewable energy supply, i.e. DSSCs (dye-sensitized solar cells) and artificial photocatalysis for the production of hydrogen, or for anticancer photodynamic therapeutic applications are reviewed. PMID:26758682

  10. 17 Ways to Say Yes: Toward Nuanced Tone of Voice in AAC and Speech Technology.

    PubMed

    Pullin, Graham; Hennig, Shannon

    2015-06-01

    People with complex communication needs who use speech-generating devices have very little expressive control over their tone of voice. Despite its importance in human interaction, the issue of tone of voice remains all but absent from AAC research and development however. In this paper, we describe three interdisciplinary projects, past, present and future: The critical design collection Six Speaking Chairs has provoked deeper discussion and inspired a social model of tone of voice; the speculative concept Speech Hedge illustrates challenges and opportunities in designing more expressive user interfaces; the pilot project Tonetable could enable participatory research and seed a research network around tone of voice. We speculate that more radical interactions might expand frontiers of AAC and disrupt speech technology as a whole. PMID:25965913

  11. Spanish language generation engine to enhance the syntactic quality of AAC systems

    NASA Astrophysics Data System (ADS)

    Narváez A., Cristian; Sastoque H., Sebastián.; Iregui G., Marcela

    2015-12-01

    People with Complex Communication Needs (CCN) face difficulties to communicate their ideas, feelings and needs. Augmentative and Alternative Communication (AAC) approaches aim to provide support to enhance socialization of these individuals. However, there are many limitations in current applications related with systems operation, target scenarios and language consistency. This work presents an AAC approach to enhance produced messages by applying elements of Natural Language Generation. Specifically, a Spanish language engine, composed of a grammar ontology and a set of linguistic rules, is proposed to improve the naturalness in the communication process, when persons with CCN tell stories about their daily activities to non-disabled receivers. The assessment of the proposed method confirms the validity of the model to improve messages quality.

  12. Structure-function properties of starch graft poly(methyl acrylate)copolymers

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Spherulites, produced by steam jet-cooking high-amylose starch and oleic acid, were grafted with methyl acrylate, both before and after removal of un-complexed amylopectin. For comparison, granular high-amylose corn starch was graft polymerized in a similar manner. The amount of grafted and ungrafte...

  13. Structure-function properties of starch spherulites grafted with poly(methyl acrylate)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Spherulites, produced by steam jet-cooking high-amylose starch and oleic acid, were grafted with methyl acrylate, both before and after removal of un-complexed amylopectin. For comparison, granular high-amylose corn starch was graft polymerized in a similar manner. The amount of grafted and ungrafte...

  14. Simultaneous Photoinduced ATRP and CuAAC Reactions for the Synthesis of Block Copolymers.

    PubMed

    Murtezi, Eljesa; Yagci, Yusuf

    2014-09-01

    Atom transfer radical polymerization (ATRP) and copper-catalyzed azide-alkyne cycloaddition (CuAAC) reactions, both utilizing copper(I) (Cu(I)) complexes, make a tremendous progress in synthetic polymer chemistry. Independently or in combination with other polymerization processes, they give access to the synthesis of polymers with well-defined structures, desired molecular architectures, and a wide variety of functionalities. Here, a novel in situ photoinduced formation of block copolymers is described by simultaneous ATRP and CuAAC processes. This approach relies on the direct reduction of initially charged copper(II) complexes to Cu(I) complexes to trigger both ATRP and CuAAC reactions coinciding under UV light at ambient temperature in one pot. Its synthetic utility is demonstrated on a model block copolymerization process by photoinduced ATRP of methyl methacrylate (MMA) using an initiator possessing acetylene functionality and concomitant click reaction between thus formed α-acetylene-poly(methyl methacrylate) (Ac-PMMA) and independently prepared azide functional polystyrene (PS-N3 ). Successful formation of PS-b-PMMA block copolymer is confirmed by FT-IR and (1) H NMR spectral analysis and gel permeation chromatography (GPC) measurements. PMID:25200624

  15. Detection of aac(6’)-Ib-cr in Avian Pathogenic Escherichia coli Isolates in Japan

    PubMed Central

    KAWANISHI, Michiko; OZAWA, Manao; HIKI, Mototaka; ABO, Hitoshi; KOJIMA, Akemi; ASAI, Tetsuo

    2013-01-01

    ABSTRACT We investigated the prevalence of plasmid-mediated quinolone resistance (PMQR) genes in avian pathogenic Escherichia coli (APEC) strains in Japan. A total of 117 APEC strains collected between 2004 and 2007 were examined for PMQR genes (qnrA, qnrB, qnrC, qnrD, qnrS, aac(6’)-Ib-cr, qepA and oqxAB) by polymerase chain reaction. None of the APEC strains carried qnrA, qnrB, qnrC, qnrD, qnrS, qepA or oqxAB, but one of the isolates was identified as an AAC (6’)-Ib-cr producer. Phylogenetic grouping, multi-locus sequence typing and serotyping showed that this isolate belonged to phylogenetic group A, sequence type 167 and untypable serogroup. To our knowledge, this is the first report of the aac (6’)-Ib-cr gene in bacteria from food-producing animals in Japan. PMID:23856759

  16. Family influences and academic success: the perceptions of individuals using AAC.

    PubMed

    Rackensperger, Tracy

    2012-06-01

    Positive family influences have a significant impact on addressing school barriers to academic success for students from socially disadvantaged backgrounds. Due to inequities and attitudes toward people with complex communication needs, positive family influences may be critical in the academic success of students using AAC. This study asked the following question of eight United States high school graduates who have used augmentative and alternative communication (AAC): How do family influences positively affect the ability of students who use AAC to succeed in the secondary academic environment? Five themes emerged from the qualitative analysis of participants' narratives: (a) the impact of the family in seeking appropriate education, (b) homework as a challenge that was made easier through the involvement of the family, (c) the role of the family in communicating the importance of education, (d) mothers as driving forces of support, and (e) family encouragement for self-determination. This research allows families and schools to recognize the needs of students and to take action to meet them. It identifies the needs of families and schools in establishing relationships with each other, in terms of supporting requirements for accommodation, learning, motivation, and self-determination of students with complex commmunication needs. PMID:22670728

  17. The Effect of Voice Output on the AAC-Supported Conversations of Persons with Alzheimer’s Disease

    PubMed Central

    Fried-Oken, Melanie; Rowland, Charity; Baker, Glory; Dixon, Mayling; Mills, Carolyn; Schultz, Darlene; Oken, Barry

    2011-01-01

    The purpose of this study was to determine whether the presence or absence of digitized 1–2 word voice output on a direct selection, customized augmentative and alternative communication (AAC) device would affect the impoverished conversations of persons with dementia. Thirty adults with moderate Alzheimer’s disease participated in two personally relevant conversations with an AAC device. For 12 of the participants the AAC device included voice output. The AAC device was the Flexiboard™ containing 16 messages needed to discuss a favorite autobiographical topic chosen by the participant and his/her family caregivers. Ten-minute conversations were videotaped in participants’ residences and analyzed for four conversational measures related to the participants’ communicative behavior. Results show that AAC devices with digitized voice output depress conversational performance and distract participants with moderate Alzheimer’s disease as compared to similar devices without voice output. There were significantly more 1-word utterances and fewer total utterances when AAC devices included voice output, and the rate of topic elaborations/initiations was significantly lower when voice output was present. Discussion about the novelty of voice output for this population of elders and the need to train elders to use this technology is provided. PMID:21785666

  18. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    PubMed Central

    Sidhu, S. K.; Shaw, S.

    1999-01-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in both the conducting gel of disposable blue diathermy pads, and artificial sculptured acrylic nails. We advocate careful history taking prior to surgery to avoid unnecessary exposure to acrylates in patients already sensitized. Images Figure 1 Figure 2 PMID:10364952

  19. New blends of ethylene-butyl acrylate copolymers with thermoplastic starch. Characterization and bacterial biodegradation.

    PubMed

    Morro, A; Catalina, F; Corrales, T; Pablos, J L; Marin, I; Abrusci, C

    2016-09-20

    Ethylene-butyl acrylate copolymer (EBA) with 13% of butyl acrylate content was used to produce blends with 10, 30 and 60% of thermoplastic starch (TPS) plasticized with glycerol. Ethylene-acrylic acid copolymer (EAA) was used as compatibilizer at 20% content with respect to EBA. The blends were characterized by X-ray diffraction, ATR-Fourier Transform Infrared Spectroscopy (ATR-FTIR), Scanning Electron Microscopy (SEM), water-Contact Angle measurements (CA), Differential Scanning Calorimetry (DSC) and Stress-strain mechanical tests. Initiated autoxidation of the polymer blends was studied by chemiluminescence (CL) confirming that the presence of the polyolefin-TPS interphase did not substantially affect the oxidative thermostability of the materials. Three bacterial species have been isolated from the blend films buried in soil and identified as Bacillus subtilis, Bacillus borstelensis and Bacillus licheniformis. Biodegradation of the blends (28days at 45°C) was evaluated by carbon dioxide measurement using the indirect impedance technique. PMID:27261731

  20. Nitrile Hydratase and Amidase from Rhodococcus rhodochrous Hydrolyze Acrylic Fibers and Granular Polyacrylonitriles

    PubMed Central

    Tauber, M. M.; Cavaco-Paulo, A.; Robra, K.-H.; Gübitz, G. M.

    2000-01-01

    Rhodococcus rhodochrous NCIMB 11216 produced nitrile hydratase (320 nkat mg of protein−1) and amidase activity (38.4 nkat mg of protein−1) when grown on a medium containing propionitrile. These enzymes were able to hydrolyze nitrile groups of both granular polyacrylonitriles (PAN) and acrylic fibers. Nitrile groups of PAN40 (molecular mass, 40 kDa) and PAN190 (molecular mass, 190 kDa) were converted into the corresponding carbonic acids to 1.8 and 1.0%, respectively. In contrast, surfacial nitrile groups of acrylic fibers were only converted to the corresponding amides. X-ray photoelectron spectroscopy analysis showed that 16% of the surfacial nitrile groups were hydrolyzed by the R. rhodochrous enzymes. Due to the enzymatic modification, the acrylic fibers became more hydrophilic and thus, adsorption of dyes was enhanced. This was indicated by a 15% increase in the staining level (K/S value) for C.I. Basic Blue 9. PMID:10742253

  1. [MORPHOLOGICAL FEATURES OF RAT MUCOUS MEMBRANE OF THE TONGUE EARLY AFFECTED BY ACRYLIC RESIN MONOMER].

    PubMed

    Davydenko, V; Nidzelskiy, M; Starchenko, I; Davydenko, A; Kuznetsov, V

    2016-03-01

    Base materials, made on the basis of various derivatives of acrylic and methacrylic acids, have been widely used in prosthetic dentistry. Free monomer, affecting the tissues of prosthetic bed and the whole body, is always found in dentures. Therefore, study of the effect of acrylic resins' monomer on mucous membrane of the tongue is crucial. Rat tongue is very similar to human tongue, and this fact has become the basis for selecting these animals to be involved into the experiment. The paper presents the findings related to the effect of "Ftoraks" base acrylic resin monomer on the state of rat mucous membrane of the tongue and its regeneration. The microscopy has found that the greatest changes in the mucous membrane of the tongue occur on day 3 and 7 day after applying the monomer and are of erosive and inflammatory nature. Regeneration of tongue epithelium slows down. PMID:27119844

  2. PERMEATION OF MULTIFUNCTIONAL ACRYLATES THROUGH THREE PROTECTIVE CLOTHING MATERIALS

    EPA Science Inventory

    Permeation tests were conducted with trimethylolpropane triacrylate TMPTA), 1,6-hexanediol diacrylate (HDDA), and two mixtures of 1,6-hexanediol diacrylate with 2-ethylhexyl acrylate (EHA) to better understand the permeation behavior of multifunctional acrylate compounds. he test...

  3. Anomerization of Acrylated Glucose During Traveling Wave Ion Mobility Spectrometry

    NASA Astrophysics Data System (ADS)

    Chendo, Christophe; Moreira, Guillaume; Tintaru, Aura; Posocco, Paola; Laurini, Erik; Lefay, Catherine; Gigmes, Didier; Viel, Stéphane; Pricl, Sabrina; Charles, Laurence

    2015-09-01

    Anomerization of simple sugars in the liquid phase is known as an acid- and base-catalyzed process, which highly depends on solvent polarity. This reaction is reported here to occur in the gas phase, during traveling wave ion mobility spectrometry (TWIMS) experiments aimed at separating α- and β-anomers of penta-acrylated glucose generated as ammonium adducts in electrospray ionization. This compound was available in two samples prepared from glucose dissolved in solvents of different polarity, namely tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAC), and analyzed by electrospray tandem mass spectrometry (ESI-MS/MS) as well as traveling wave ion mobility (ESI-TWIMS-MS). In MS/MS, an anchimerically-assisted process was found to be unique to the electrosprayed α-anomer, and was only observed for the THF sample. In ESI-TWIMS-MS, a signal was measured at the drift time expected for the α-anomer for both the THF and DMAC samples, in apparent contradiction to the MS/MS results, which indicated that the α-anomer was not present in the DMAC sample. However, MS/MS experiments performed after TWIMS separation revealed that ammonium adducts of the α-anomer produced from each sample, although exhibiting the same collision cross section, were clearly different. Indeed, while the α-anomer actually present in the THF sample was electrosprayed with the ammonium adducted at the C2 acrylate, its homologue only observed when the DMAC sample was subjected to TWIMS hold the adducted ammonium at the C1 acrylate. These findings were explained by a β/α inter-conversion upon injection in the TWIMS cell, as supported by theoretical calculation and dynamic molecular modeling.

  4. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate ester copolymer coating. 175.210 Section... COATINGS Substances for Use as Components of Coatings § 175.210 Acrylate ester copolymer coating. Acrylate ester copolymer coating may safely be used as a food-contact surface of articles intended for...

  5. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  6. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare a scan from 10.5 microns...

  7. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  8. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  9. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  10. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  11. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  12. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  13. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  14. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  15. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  16. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  17. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  18. 40 CFR 721.10528 - Modified fluorinated acrylates (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Modified fluorinated acrylates... Specific Chemical Substances § 721.10528 Modified fluorinated acrylates (generic). (a) Chemical substances... modified fluorinated acrylates (PMNs P-12-30, P-12-31, and P-12-32) are subject to reporting under...

  19. 40 CFR 721.10528 - Modified fluorinated acrylates (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Modified fluorinated acrylates... Specific Chemical Substances § 721.10528 Modified fluorinated acrylates (generic). (a) Chemical substances... modified fluorinated acrylates (PMNs P-12-30, P-12-31, and P-12-32) are subject to reporting under...

  20. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  1. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  2. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  3. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. Link to an amendment published at 79 FR 34637, June 18, 2014... nickel acrylate complex (PMN P-85-1034) is subject to reporting under this section for the...

  4. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  5. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  6. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  7. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  8. Analytical Results from the Area G Nitrate Salt Samples Submitted to C-AAC

    SciTech Connect

    Drake, Lawrence Randall

    2014-09-03

    Table 1 is a summary of the analysis results on sample 4174-1-6/7 and 4174-2-6/7. The results in Table 2 are the major and trace metals analysis values. Samples 4174-1-6 and 4174-2-7 were introduced into a radiological glovebox in CMR for partitioning and analysis. Samples 4174-1-7 and 4174-2-6 were assayed by gamma spectrometry and then sent to TA 48 (C-NR) for further analysis. The validated analytical procedures used by C-AAC are cited at the end of this document. The results have not been approved by formal QA release.

  9. ASME N510 test results for Savannah River Site AACS filter compartments

    SciTech Connect

    Paul, J.D.; Punch, T.M.

    1995-02-01

    The K-Reactor at the Savannah River Site recently implemented design improvements for the Airborne Activity Confinement System (AACS) by procuring, installing, and testing new Air Cleaning Units, or filter compartments, to ASME AG-11, N509, and N510 requirements. Specifically, these new units provide documentable seismic resistance to a Design Basis Accident earthquake, provide 2 inch adsorber beds with 0.25 second residence time, and meet all AG-1, N509, and N510 requirements for testability and maintainability. This paper presents the results of the Site acceptance testing and discusses an issue associated with sample manifold qualification testing.

  10. Organization of the 16th Advanced Accelerator Concepts (AAC) Workshop by Stanford University

    SciTech Connect

    Huang, Zhirong; Hogan, Mark

    2015-09-30

    Essentially all we know today and will learn in the future about the fundamental nature of matter is derived from probing it with directed beams of particles such as electrons, protons, neutrons, heavy ions, and photons. The resulting ability to “see” the building blocks of matter has had an immense impact on society and our standard of living. Over the last century, particle accelerators have changed the way we look at nature and the universe we live in and have become an integral part of the Nation’s technical infrastructure. Today, particle accelerators are essential tools of modern science and technology. The cost and capabilities of accelerators would be greatly enhanced by breakthroughs in acceleration methods and technology. For the last 32 years, the Advanced Accelerator Concepts (AAC) Workshop has acted as the focal point for discussion and development of the most promising acceleration physics and technology. It is a particularly effective forum where the discussion is leveraged and promoted by the unique and demanding feature of the AAC Workshop: the working group structure, in which participants are asked to consider their contributions in terms of even larger problems to be solved. The 16th Advanced Accelerator Concepts (AAC2014) Workshop was organized by Stanford University from July 13 - 18, 2014 at the Dolce Hays Mansion in San Jose, California. The conference had a record 282 attendees including 62 students. Attendees came from 11 countries representing 66 different institutions. The workshop format consisted of plenary sessions in the morning with topical leaders from around the world presenting the latest breakthroughs to the entire workshop. In the late morning and afternoons attendees broke out into eight different working groups for more detailed presentations and discussions that were summarized on the final day of the workshop. In addition, there were student tutorial presentations on two afternoons to provide in depth education and

  11. Copper-catalysed azide-alkyne cycloadditions (CuAAC): an update.

    PubMed

    Haldón, Estela; Nicasio, M Carmen; Pérez, Pedro J

    2015-10-01

    The reactions of organic azides and alkynes catalysed by copper species represent the prototypical examples of click chemistry. The so-called CuAAC reaction (copper-catalysed azide-alkyne cycloaddition), discovered in 2002, has been expanded since then to become an excellent tool in organic synthesis. In this contribution the recent results described in the literature since 2010 are reviewed, classified according to the nature of the catalyst precursor: copper(I) or copper(II) salts or complexes, metallic or nano-particulated copper and several solid-supported copper systems. PMID:26284434

  12. A solid-phase CuAAC strategy for the synthesis of PNA containing nucleobase surrogates

    PubMed Central

    St. Amant, André H.; Engbers, Christopher; Hudson, Robert H.E.

    2013-01-01

    The synthesis of an azide containing PNA monomer is described. The monomer was incorporated into two PNA sequences for the purpose of synthesizing an intercalating fluorophore-labeled PNA and a metal binding hairpin using a solid phase copper catalyzed azide-alkyne Huisgen cycloaddition (CuAAC). Click chemistry was performed using 2-ethynylfluorene or 1-ethynylpyrene to add a fluorophore to the PNA, which were tested for their ability to recognize an abasic site on a DNA target. A PNA hairpin possessing azide monomers at each termini was synthesized and reacted with 2-ethynylpyridine to form a hairpin that is stabilized by Ni2+. PMID:23422048

  13. Thermodynamic Interactions between Polystyrene and Long-Chain Poly(n-Alkyl Acrylates) Derived from Plant Oils.

    PubMed

    Wang, Shu; Robertson, Megan L

    2015-06-10

    Vegetable oils and their fatty acids are promising sources for the derivation of polymers. Long-chain poly(n-alkyl acrylates) and poly(n-alkyl methacrylates) are readily derived from fatty acids through conversion of the carboxylic acid end-group to an acrylate or methacrylate group. The resulting polymers contain long alkyl side-chains with around 10-22 carbon atoms. Regardless of the monomer source, the presence of alkyl side-chains in poly(n-alkyl acrylates) and poly(n-alkyl methacrylates) provides a convenient mechanism for tuning their physical properties. The development of structured multicomponent materials, including block copolymers and blends, containing poly(n-alkyl acrylates) and poly(n-alkyl methacrylates) requires knowledge of the thermodynamic interactions governing their self-assembly, typically described by the Flory-Huggins interaction parameter χ. We have investigated the χ parameter between polystyrene and long-chain poly(n-alkyl acrylate) homopolymers and copolymers: specifically we have included poly(stearyl acrylate), poly(lauryl acrylate), and their random copolymers. Lauryl and stearyl acrylate were chosen as model alkyl acrylates derived from vegetable oils and have alkyl side-chain lengths of 12 and 18 carbon atoms, respectively. Polystyrene is included in this study as a model petroleum-sourced polymer, which has wide applicability in commercially relevant multicomponent polymeric materials. Two independent methods were employed to measure the χ parameter: cloud point measurements on binary blends and characterization of the order-disorder transition of triblock copolymers, which were in relatively good agreement with one another. The χ parameter was found to be independent of the alkyl side-chain length (n) for large values of n (i.e., n > 10). This behavior is in stark contrast to the n-dependence of the χ parameter predicted from solubility parameter theory. Our study complements prior work investigating the interactions between

  14. Characteristics and mechanisms of acrylate polymer damage to maize seedlings.

    PubMed

    Chen, Xian; Mao, Xiaoyun; Lu, Qin; Liao, Zongwen; He, Zhenli

    2016-07-01

    Superabsorbent acrylate polymers (SAPs) have been widely used to maintain soil moisture in agricultural management, but they may cause damage to plants, and the mechanisms are not well understood. In this study, seed germination, soil pot culture, hydroponic experiments, and SAPs degradation were conducted to investigate damage characteristics and mechanisms associated with SAPs application. The Results showed that SAPs inhibited maize growth and altered root morphology (irregular and loose arrangement of cells and breakage of cortex parenchyma), and the inhibitory effects were enhanced at higher SAPs rates. After 1h SAP hydrogels treatment, root malondialdehyde (MDA) content was significantly increased, while superoxide dismutase (SOD) and catalase (CAT) content were significantly decreased. Hydroponics experiment indicated that root and shoot growth was inhibited at 2.5mgL(-1) acrylic acid (AA), and the inhibition was enhanced with increasing AA rates. This effect was exacerbated by the presence of Na(+) at a high concentration in the hydrogels. Release and degradation of AA were enhanced at higher soil moisture levels. A complete degradation of AA occurred between 15 and 20 days after incubation (DAI), but it took longer for Na(+) concentration to decrease to a safe level. These results indicate that high concentration of both AA and Na(+) present in the SAPs inhibits plant growth. The finding of this study may provide a guideline for appropriate application of SAPs in agriculture. PMID:27057990

  15. 40 CFR 721.405 - Polyether acrylate.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polyether acrylate. 721.405 Section 721.405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL...) The significant new uses are: (i) Release to water. Requirements as specified in § 721.90 (a)(1),...

  16. Worn down nails after acrylic nail removal.

    PubMed

    Wu, Timothy P; Morrison, Brian W; Tosti, Antonella

    2015-01-01

    Worn-down nail syndrome is a nail disorder characterized by thinning of the distal nail plate caused by repetitive chemical or mechanical trauma. We present a previously undescribed source of worn-down nail syndrome caused by trauma from nail filing after acrylic nail removal. PMID:25612131

  17. Acrylic Tanks for Stunning Chemical Demonstrations

    ERIC Educational Resources Information Center

    Mirholm, Alexander; Ellervik, Ulf

    2009-01-01

    We describe the use of acrylic tanks (400 x 450 x 27 mm) for visualization of chemical demonstrations in aqueous solutions. Examples of well-suited demonstrations are oscillating reactions, pH indicators, photochemical reduction of Lauth's violet, and chemoluminiscent reactions. (Contains 1 figure.)

  18. UV-curable acrylated coating from epoxidized palm oil

    NASA Astrophysics Data System (ADS)

    Rahman, Nurliyana Abd; Badri, Khairiah Haji; Salleh, Nik Ghazali Nik

    2014-09-01

    The properties of coating film prepared from the incorporation of acrylated palm oil (EPOLA) in commercial epoxy acrylate have been studied. A series of different amount of EPOLA was mixed with commercial epoxy acrylate. The blended acrylates passed through UV light to produce a non-tacky film. The conversion of acrylate double bond was monitored by FTIR. The effect of EPOLA concentration onto coated films were investigated by determination of the pendulum hardness and gel content. The higher the amount of EPOLA, the lower the pendulum hardness and the gel content but to a level acceptable for usage in the high-end applications.

  19. Influence of Computerized Sounding Out on Spelling Performance for Children who do and not rely on AAC

    PubMed Central

    McCarthy, Jillian H.; Hogan, Tiffany P.; Beukelman, David R.; Schwarz, Ilsa E.

    2015-01-01

    Purpose Spelling is an important skill for individuals who rely on augmentative alternative communication (AAC). The purpose of this study was to investigate how computerized sounding out influenced spelling accuracy of pseudo-words. Computerized sounding out was defined as a word elongated, thus providing an opportunity for a child to hear all the sounds in the word at a slower rate. Methods Seven children with cerebral palsy, four who use AAC and three who do not, participated in a single subject AB design. Results The results of the study indicated that the use of computerized sounding out increased the phonologic accuracy of the pseudo-words produced by participants. Conclusion The study provides preliminary evidence for the use of computerized sounding out during spelling tasks for children with cerebral palsy who do and do not use AAC. Future directions and clinical implications are discussed. PMID:24512195

  20. Predicting language outcomes for children learning AAC: Child and environmental factors

    PubMed Central

    Brady, Nancy C.; Thiemann-Bourque, Kathy; Fleming, Kandace; Matthews, Kris

    2014-01-01

    Purpose To investigate a model of language development for nonverbal preschool age children learning to communicate with AAC. Method Ninety-three preschool children with intellectual disabilities were assessed at Time 1, and 82 of these children were assessed one year later at Time 2. The outcome variable was the number of different words the children produced (with speech, sign or SGD). Children’s intrinsic predictor for language was modeled as a latent variable consisting of cognitive development, comprehension, play, and nonverbal communication complexity. Adult input at school and home, and amount of AAC instruction were proposed mediators of vocabulary acquisition. Results A confirmatory factor analysis revealed that measures converged as a coherent construct and an SEM model indicated that the intrinsic child predictor construct predicted different words children produced. The amount of input received at home but not at school was a significant mediator. Conclusions Our hypothesized model accurately reflected a latent construct of Intrinsic Symbolic Factor (ISF). Children who evidenced higher initial levels of ISF and more adult input at home produced more words one year later. Findings support the need to assess multiple child variables, and suggest interventions directed to the indicators of ISF and input. PMID:23785187