Science.gov

Sample records for activated sludge bioreactors

  1. Effect of membrane bioreactor configurations on sludge structure and microbial activity.

    PubMed

    Clouzot, L; Roche, N; Marrot, B

    2011-01-01

    The aim of this paper was to determine the effect of two different membrane bioreactor (MBR) configurations (external/immersed) on sludge structure and microbial activity. Sludge structure was deduced from rheological measurements. The high shear stress induced by the recirculation pump in the external MBR was shown to result in decreasing viscosity due to activated sludge (AS) deflocculation. Besides, soluble microbial products (SMP) release was higher in the external MBR (5 mgCOD gMLVSS(-1)) than in the immersed configuration (2 mgCOD gMLVSS(-1)). Microbial activity was followed from respirometry tests by focusing on the distinction between heterotrophs and autotrophs. An easier autotrophic microbe development was then observed in the immersed MBR compared to the external one. However, the external MBR was shown to allow better heterotrophic microbe development. PMID:20947340

  2. A hybrid anaerobic membrane bioreactor coupled with online ultrasonic equipment for digestion of waste activated sludge.

    PubMed

    Xu, Meilan; Wen, Xianghua; Yu, Zhiyong; Li, Yushan; Huang, Xia

    2011-05-01

    Anaerobic membrane bioreactor and online ultrasonic equipment used to enhance membrane filtration were coupled to form a hybrid system (US-AnMBR) designed for long-term digestion of waste activated sludge. The US-AnMBR was operated under volatile solids loading rates of 1.1-3.7 gVS/L·d. After comprehensive studies on digestion performance and membrane fouling control in the US-AnMBR, the final loading rate was determined to be 2.7 gVS/L·d with 51.3% volatile solids destruction. In the US-AnMBR, the improved digestion was due to enhanced sludge disintegration, as indicated by soluble matter comparison in the supernatant and particle size distribution in the digested sludge. Maximum specific methanogenic activity revealed that ultrasound application had no negative effect on anaerobic microorganisms. Furthermore, implementing ultrasound effectively controlled membrane fouling and successfully facilitated membrane bioreactor operation. This lab-scale study demonstrates the potential feasibility and effectiveness of setting up a US-AnMBR system for sludge digestion. PMID:21421308

  3. A comparison of the physical, chemical, and biological properties of sludges from a complete-mix activated sludge reactor and a submerged membrane bioreactor.

    PubMed

    Merlo, Rion P; Trussell, R Shane; Hermanowicz, Slawomir W; Jenkins, David

    2007-03-01

    The properties of sludges from a pilot-scale submerged membrane bioreactor (SMBR) and two bench-scale complete-mix, activated sludge (CMAS) reactors treating municipal primary effluent were determined. Compared with the CMAS sludges, the SMBR sludge contained a higher amount of soluble microbial products (SMP) and colloidal material attributed to the use of a membrane for solid-liquid separation; a higher amount nocardioform bacteria, resulting from efficient foam trapping; and a lower amount of extracellular polymeric substances (EPS), possibly because there was no selective pressure for the sludge to settle. High aeration rates in both the CMAS and SMBR reactors produced sludges with higher numbers of smaller particles. Normalized capillary suction time values for the SMBR sludge were lower than for the CMAS sludges, possibly because of its lower EPS content. PMID:17469664

  4. Iron and phosphorus speciation in Fe-conditioned membrane bioreactor activated sludge.

    PubMed

    Wu, Hao; Ikeda-Ohno, Atsushi; Wang, Yuan; Waite, T David

    2015-06-01

    Iron dosing of membrane bioreactors (MBRs) is widely used as a means of meeting effluent phosphorus targets but there is limited understanding of the nature of iron and phosphorus-containing solids that are formed within the bioreactor (an important issue in view of the increasing interest in recovering phosphorus from wastewaters). Of particular challenge is the complexity of the MBR system and the variety of reactions that can occur on addition of iron salts to a membrane bioreactor. In this study, the performances of bench scale MBRs with dosing of either ferrous or ferric salts were monitored for a period of four months. The distributions of Fe and P-species in the Fe-conditioned sludges were determined using X-ray absorption spectroscopy (XAS) at the Fe K-edge and the P K-edge. Regardless of whether iron was dosed to the anoxic or aerobic chambers and regardless of whether ferrous (Fe(II)) or ferric (Fe(III)) iron was dosed, iron present in the minerals in the conditioned sludges was consistently in the +III oxidation state. Fitting of the Fe K-edge EXAFS spectra revealed that an Fe(III)-phosphate species was the main Fe species present in all cases with the remaining fraction dominated by lepidocrocite (γ-FeOOH) in the Fe(II)-dosed case and ferrihydrite (am-FeOOH) in the Fe(III)-dosed case. Approximately half the phosphorus in the activated sludge samples was present as a distinct Fe-PO4 mineral (such as strengite or an amorphous ferric hydroxyl phosphate analogue of strengite) and half as phosphorus adsorbed to an iron oxyhydroxide mineral phase indicating that both co-precipitation and adsorption of phosphorus by iron contribute to removal of phosphorus from the MBR supernatant. PMID:25900910

  5. Enhanced waste activated sludge digestion using a submerged anaerobic dynamic membrane bioreactor: performance, sludge characteristics and microbial community

    PubMed Central

    Yu, Hongguang; Wang, Zhiwei; Wu, Zhichao; Zhu, Chaowei

    2016-01-01

    Anaerobic digestion (AD) plays an important role in waste activated sludge (WAS) treatment; however, conventional AD (CAD) process needs substantial improvements, especially for the treatment of WAS with low solids content and poor anaerobic biodegradability. Herein, we propose a submerged anaerobic dynamic membrane bioreactor (AnDMBR) for simultaneous WAS thickening and digestion without any pretreatment. During the long-term operation, the AnDMBR exhibited an enhanced sludge reduction and improved methane production over CAD process. Moreover, the biogas generated in the AnDMBR contained higher methane content than CAD process. Stable carbon isotopic signatures elucidated the occurrence of combined methanogenic pathways in the AnDMBR process, in which hydrogenotrophic methanogenic pathway made a larger contribution to the total methane production. It was also found that organic matter degradation was enhanced in the AnDMBR, thus providing more favorable substrates for microorganisms. Pyrosequencing revealed that Proteobacteria and Bacteroidetes were abundant in bacterial communities and Methanosarcina and Methanosaeta in archaeal communities, which played an important role in the AnDMBR system. This study shed light on the enhanced digestion of WAS using AnDMBR technology. PMID:26830464

  6. Enhanced waste activated sludge digestion using a submerged anaerobic dynamic membrane bioreactor: performance, sludge characteristics and microbial community

    NASA Astrophysics Data System (ADS)

    Yu, Hongguang; Wang, Zhiwei; Wu, Zhichao; Zhu, Chaowei

    2016-02-01

    Anaerobic digestion (AD) plays an important role in waste activated sludge (WAS) treatment; however, conventional AD (CAD) process needs substantial improvements, especially for the treatment of WAS with low solids content and poor anaerobic biodegradability. Herein, we propose a submerged anaerobic dynamic membrane bioreactor (AnDMBR) for simultaneous WAS thickening and digestion without any pretreatment. During the long-term operation, the AnDMBR exhibited an enhanced sludge reduction and improved methane production over CAD process. Moreover, the biogas generated in the AnDMBR contained higher methane content than CAD process. Stable carbon isotopic signatures elucidated the occurrence of combined methanogenic pathways in the AnDMBR process, in which hydrogenotrophic methanogenic pathway made a larger contribution to the total methane production. It was also found that organic matter degradation was enhanced in the AnDMBR, thus providing more favorable substrates for microorganisms. Pyrosequencing revealed that Proteobacteria and Bacteroidetes were abundant in bacterial communities and Methanosarcina and Methanosaeta in archaeal communities, which played an important role in the AnDMBR system. This study shed light on the enhanced digestion of WAS using AnDMBR technology.

  7. Enhanced waste activated sludge digestion using a submerged anaerobic dynamic membrane bioreactor: performance, sludge characteristics and microbial community.

    PubMed

    Yu, Hongguang; Wang, Zhiwei; Wu, Zhichao; Zhu, Chaowei

    2016-01-01

    Anaerobic digestion (AD) plays an important role in waste activated sludge (WAS) treatment; however, conventional AD (CAD) process needs substantial improvements, especially for the treatment of WAS with low solids content and poor anaerobic biodegradability. Herein, we propose a submerged anaerobic dynamic membrane bioreactor (AnDMBR) for simultaneous WAS thickening and digestion without any pretreatment. During the long-term operation, the AnDMBR exhibited an enhanced sludge reduction and improved methane production over CAD process. Moreover, the biogas generated in the AnDMBR contained higher methane content than CAD process. Stable carbon isotopic signatures elucidated the occurrence of combined methanogenic pathways in the AnDMBR process, in which hydrogenotrophic methanogenic pathway made a larger contribution to the total methane production. It was also found that organic matter degradation was enhanced in the AnDMBR, thus providing more favorable substrates for microorganisms. Pyrosequencing revealed that Proteobacteria and Bacteroidetes were abundant in bacterial communities and Methanosarcina and Methanosaeta in archaeal communities, which played an important role in the AnDMBR system. This study shed light on the enhanced digestion of WAS using AnDMBR technology. PMID:26830464

  8. Comparison of microbial communities of activated sludge and membrane biofilm in 10 full-scale membrane bioreactors.

    PubMed

    Jo, Sung Jun; Kwon, Hyeokpil; Jeong, So-Yeon; Lee, Chung-Hak; Kim, Tae Gwan

    2016-09-15

    Operation of membrane bioreactors (MBRs) for wastewater treatment is hampered by the membrane biofouling resulting from microbial activities. However, the knowledge of the microbial ecology of both biofilm and activated sludge in MBRs has not been sufficient. In this study, we scrutinized microbial communities of biofilm and activated sludge from 10 full-scale MBR plants. Overall, Flavobacterium, Dechloromonas and Nitrospira were abundant in order of abundance in biofilm, whereas Dechloromonas, Flavobacterium and Haliscomenobacter in activated sludge. Community structure was analyzed in either biofilm or activated sludge. Among MBRs, as expected, not only diversity of microbial community but also its composition was different from one another (p < 0.05). Between the biofilm and activated sludge, community composition made significant difference, but its diversity measures (i.e., alpha diversity, e.g., richness, diversity and evenness) did not (p > 0.05). Effects of ten environmental factors on community change were investigated using Spearman correlation. MLSS, HRT, F/M ratio and SADm explained the variation of microbial composition in the biofilm, whereas only MLSS did in the activated sludge. Microbial networks were constructed with the 10 environmental factors. The network results revealed that there were different topological characteristics between the biofilm and activated sludge networks, in which each of the 4 factors had different associations with microbial nodes. These results indicated that the different microbial associations were responsible for the variation of community composition between the biofilm and activated sludge. PMID:27262549

  9. Formation and removal of dissolved organic nitrogen (DON) in membrane bioreactor and conventional activated sludge processes.

    PubMed

    Han, Xiaomeng; Wang, Zhiwei; Ma, Jinxing; Zheng, Junjian; Wang, Pan; Wu, Zhichao

    2015-08-01

    Dissolved organic nitrogen (DON) has become a growing concern due to its contribution to eutrophication and nitrogenous disinfection byproducts (N-DBPs) formation. However, information of DON in membrane bioreactors (MBRs) is very limited. In this study, occurrence, transformation and fate of DON in an MBR system were systematically investigated. MBR sludge showed a larger hydrolysis rate of particle organic nitrogen (PON) and also a higher transformation rate of DON to nitrate compared to conventional activated sludge (CAS). For long-term experiments, MBR achieved higher DON removal efficiency at low temperature than CAS; however, at high temperature, the effluent DON concentrations were almost the same in both systems. Batch tests on DON biodegradability showed that DON concentration increased and large molecular weight DON accumulated after 3-h aeration at low temperature, while DON concentration continuously decreased with the increase of aeration time at high temperature. The obtained results provide insights in DON removal in MBRs for meeting increasingly stringent regulations in terms of nitrogen removal. PMID:25911287

  10. Start-up of the ananmmox process from the conventional activated sludge in a hybrid bioreactor.

    PubMed

    Duan, Xiumei; Zhou, Jiti; Qiao, Sen; Yin, Xin; Tian, Tian; Xu, Fangdi

    2012-01-01

    The anaerobic ammonium oxidation (anammox) process was successfully started up from conventional activated sludge using a hybrid bioreactor within 2 months. The average removal efficiencies of ammonia and nitrite were both over 80%, and the maximum total nitrogen removal rate of 1.85 kg N/(m3 x day) was obtained on day 362 with the initial sludge concentration of 0.7 g mixed liquor suspended solids (MLSS)/L. Scanning electron microscope (SEM) observation of the granular sludge in the hybrid reactor clearly showed a high degree of compactness and cell sphericity, and the cell size was quite uniform. Transmission electron microscope photos showed that cells were round or oval, the cellular diameter was 0.6-1.0 microm, and the percentage of the anammoxosome compartment was 51%-85% of the whole cell volume. Fluorescence in situ hybridization analysis (FISH) indicated that anammox bacteria became the dominant population in the community (accounting for more than 51% of total bacteria on day 250). Seven planctomycete 16S rRNA gene sequences were present in the 16S rRNA gene clone library generated from the biomass and affiliated to Candidatus Kuenenia stuttgartiensis and Candidatus Brocadia sp., a new anammox species. In addition, the average effluent suspended solid (MLSS) concentrations of outlets I (above the non-woven carrier) and II (below the non-woven carrier) were 0.0009 and 0.0035 g/L, respectively. This showed that the non-woven carrier could catch the biomass effectively, which increased biomass and improved the nitrogen removal rate in the reactor. PMID:23505876

  11. Bacterial Community Dynamics in Full-Scale Activated Sludge Bioreactors: Operational and Ecological Factors Driving Community Assembly and Performance

    PubMed Central

    Valentín-Vargas, Alexis; Toro-Labrador, Gladys; Massol-Deyá, Arturo A.

    2012-01-01

    The assembling of bacterial communities in conventional activated sludge (CAS) bioreactors was thought, until recently, to be chaotic and mostly unpredictable. Studies done over the last decade have shown that specific, and often, predictable random and non-random factors could be responsible for that process. These studies have also motivated a “structure–function” paradigm that is yet to be resolved. Thus, elucidating the factors that affect community assembly in the bioreactors is necessary for predicting fluctuations in community structure and function. For this study activated sludge samples were collected during a one-year period from two geographically distant CAS bioreactors of different size. Combining community fingerprinting analysis and operational parameters data with a robust statistical analysis, we aimed to identify relevant links between system performance and bacterial community diversity and dynamics. In addition to revealing a significant β-diversity between the bioreactors’ communities, results showed that the largest bioreactor had a less dynamic but more efficient and diverse bacterial community throughout the study. The statistical analysis also suggests that deterministic factors, as opposed to stochastic factors, may have a bigger impact on the community structure in the largest bioreactor. Furthermore, the community seems to rely mainly on mechanisms of resistance and functional redundancy to maintain functional stability. We suggest that the ecological theories behind the Island Biogeography model and the species-area relationship were appropriate to predict the assembly of bacterial communities in these CAS bioreactors. These results are of great importance for engineers and ecologists as they reveal critical aspects of CAS systems that could be applied towards improving bioreactor design and operation. PMID:22880016

  12. Isolation and Molecular Characterization of Biofouling Bacteria and Profiling of Quorum Sensing Signal Molecules from Membrane Bioreactor Activated Sludge

    PubMed Central

    Lade, Harshad; Paul, Diby; Kweon, Ji Hyang

    2014-01-01

    The formation of biofilm in a membrane bioreactor depends on the production of various signaling molecules like N-acyl homoserine lactones (AHLs). In the present study, a total of 200 bacterial strains were isolated from membrane bioreactor activated sludge and screened for AHLs production using two biosensor systems, Chromobacterium violaceum CV026 and Agrobacterium tumefaciens A136. A correlation between AHLs production and biofilm formation has been made among screened AHLs producing strains. The 16S rRNA gene sequence analysis revealed the dominance of Aeromonas and Enterobacter sp. in AHLs production; however few a species of Serratia, Leclercia, Pseudomonas, Klebsiella, Raoultella and Citrobacter were also identified. The chromatographic characterization of sludge extract showed the presence of a broad range of quorum sensing signal molecules. Further identification of sludge AHLs by thin layer chromatography bioassay and high performance liquid chromatography confirms the presence of C4-HSL, C6-HSL, C8-HSL, 3-oxo-C8-HSL, C10-HSL, C12-HSL, 3-oxo-C12-HSL and C14-HSL. The occurrence of AHLs in sludge extract and dominance of Aeromonas and Enterobacter sp. in activated sludge suggests the key role of these bacterial strains in AHLs production and thereby membrane fouling. PMID:24499972

  13. Isomer-specific biodegradation of nonylphenol in an activated sludge bioreactor and structure-biodegradability relationship.

    PubMed

    Lu, Zhijiang; Reif, Rubén; Gan, Jay

    2015-01-01

    Nonylphenol (NP), one of the priority hazardous substances, is in fact a mixture of numerous isomers. It is inconclusive whether or not biodegradation during wastewater treatment process is isomer-specific, leading to the environmental release of NP in different isomer profiles. In this study, we evaluated the isomer selectivity of 19 NP isomers in a laboratory-scale continuous flow conventional activated sludge bioreactor under various operational conditions. The removal efficiency of NP isomers ranged from 90 to 99%, depending on the operational conditions and isomer structures. Isomer selective biodegradation resulted in the increase of composition of recalcitrant isomers, such as, NP₁₉₃a/b, NP₁₁₀a and NP₁₉₄ in the effluent. Moreover, biodegradability was related to the bulkiness of α-substituents and followed α-dimethyl > α-ethyl-α-methyl > α-methyl-α-n-propyl > α-iso-propyl-α-methyl. Steric effect index, a quantitative descriptor of steric hindrance, was linearly correlated with residues of NP isomers in the effluent (R² = 0.76). Decrease of temperature to 10 °C decreased the overall biodegradability and also enhanced the relative enrichment of recalcitrant isomers. These findings suggest that isomer compositions of NP entering the environment may be different from those in technical mixtures and that isomeric selectivity should be taken into account to better understand the occurrence, fate, and ecological risks of NP. PMID:25462736

  14. Salt stress in a membrane bioreactor: dynamics of sludge properties, membrane fouling and remediation through powdered activated carbon dosing.

    PubMed

    De Temmerman, L; Maere, T; Temmink, H; Zwijnenburg, A; Nopens, I

    2014-10-15

    Membrane bioreactors are a well-established technology for wastewater treatment. However, their efficiency is adversely impacted by membrane fouling, primarily inciting very conservative operations of installations that makes them less appealing from an economic perspective. This fouling propensity of the activated sludge is closely related to system disturbances. Therefore, improved insight into the impact of fouling is crucial towards increased membrane performance. In this work, the disturbance of a salt shock was investigated with respect to sludge composition and filterability in two parallel lab-scale membrane bioreactors. Several key sludge parameters (soluble microbial products, sludge-bound extracellular polymeric substances, supramicron particle size distributions (PSD), submicron particle concentrations) were intensively monitored prior to, during, and after a disturbance to investigate its impact as well as the potential governing mechanism. Upon salt addition, the supramicron PSD immediately shifted to smaller floc sizes, and the total fouling rate increased. Following a certain delay, an increase in submicron particles, supernatant proteins, and polysaccharides was observed as well as an increase in the irreversible membrane fouling rate. Recovery from the disturbance was evidenced with a simultaneous decrease in the above mentioned quantities. A similar experiment introducing powdered activated carbon (PAC) addition used for remediation resulted in either no or less significant changes in the above mentioned quantities, signifying its potential as a mitigation strategy. PMID:24999116

  15. Heavy metal speciation and acid treatment of activated sludge developed in a membrane bioreactor.

    PubMed

    Daskalakis, N; Katsou, E; Malamis, S; Haralambous, K J

    2013-01-01

    The aim of this study was to identify the heavy metals forms (exchangeable and bound to carbonate, Fe/Mn oxides, bound to organic matter and sulphide, and residual) associated with different fractions of excess sludge produced by a membrane bioreactor (MBR). Furthermore, the release of metals from the sludge to the liquid was investigated by applying acid treatment using 10% (v/v) H2SO4 (T = 25 degrees C, solid-liquid ratio 1:5 w/v) for contact time ranging from 15 min to 4 h. Metal partitioning in sludge, as determined by the sequential chemical extraction showed that the dominant form of both Ni and Zn was bound to the exchangeable and carbonate fraction; the latter were very unstable and sensitive to environmental conditions. The dominant Cu fraction was bound to organic matter and sulphide, while Pb was found to be mainly in the residual fraction which is very stable. Metal speciation after acidification with H2SO4 indicates changes of metal content in sludge and an increase of the exchangeable and bound to carbonate fraction for all metals except Cu. Acidification resulted in removal of 82% for Ni, 78% for Zn, 47% for Cu and 45% for Pb. PMID:24527621

  16. Modelling a full scale membrane bioreactor using Activated Sludge Model No.1: challenges and solutions.

    PubMed

    Delrue, F; Choubert, J M; Stricker, A E; Spérandio, M; Mietton-Peuchot, M; Racault, Y

    2010-01-01

    A full-scale membrane bioreactor (1,600 m(3) d(-1)) was monitored for modelling purposes during the summer of 2006. A complete calibration of the ASM1 model is presented, in which the key points were the wastewater characterisation, the oxygen transfer and the biomass kinetics. Total BOD tests were not able to correctly estimate the biodegradable fraction of the wastewater. Therefore the wastewater fractionation was identified by adjusting the simulated sludge production rate to the measured value. MLVSS and MLSS were accurately predicted during both calibration and validation periods (20 and 30 days). Because the membranes were immerged in the aeration tank, the coarse bubble and fine bubble diffusion systems coexisted in the same tank. This allowed five different aeration combinations, depending whether the 2 systems were operating separately or simultaneously, and at low speed or high speed. The aeration control maintained low DO concentrations, allowing simultaneous nitrification and denitrification. This made it difficult to calibrate the oxygen transfer. The nitrogen removal kinetics were determined using maximum nitrification rate tests and an 8-hour intensive sampling campaign. Despite the challenges encountered, a calibrated set of parameters was identified for ASM1 that gave very satisfactory results for the calibration period. Matching simulated and measured data became more difficult during the validation period, mainly because the dominant aeration configuration had changed. However, the merit of this study is to be the first effort to simulate a full-scale MBR plant. PMID:21076205

  17. Effect of carbon to nitrogen ratio of feed wastewater and sludge retention time on activated sludge in a submerged membrane bioreactor.

    PubMed

    Erkan, Hanife Sari; Onkal Engin, Guleda; Ince, Mahir; Bayramoglu, Mahmut R

    2016-06-01

    This paper investigated the effects of extracellular polymeric substances (EPS) on the activated sludge rheology in a submerged membrane bioreactor (sMBR) operated at different sludge retention time (SRT) values and different carbon to nitrogen ratios (C/N) of feed wastewater. The C/N ratios of the feed were adjusted accordingly so that synthetic wastewaters prepared simulated municipal wastewater, non-toxic wastewater with high C/N ratio and non-toxic wastewater with low C/N ratio. A number of important operational parameters such as mixed liquor suspended solid (MLSS), protein fraction of EPS (EPSp), carbohydrate fraction of EPS (EPSc), protein fraction of soluble microbial product (SMPp), carbohydrate fraction of SMP (SMPc), apparent viscosity, critical flux and hydrophobicity in mixed liquor and their correlations were investigated in the sMBR systems operated. The statistical analysis indicated that the C/N ratio of feed, SRT, MLSS and SMPc were found to have positive effects on apparent viscosity at three different shear rates. On the other hand, a negative impact was detected between the apparent viscosities and the critical fluxes. It was also observed that there is a significant positive correlation between hydrophobicity and both EPSp and SMPp. PMID:26888531

  18. Mutual interactions of Pleurotus ostreatus with bacteria of activated sludge in solid-bed bioreactors.

    PubMed

    Svobodová, Kateřina; Petráčková, Denisa; Kozická, Barbora; Halada, Petr; Novotný, Čeněk

    2016-06-01

    White rot fungi are well known for their ability to degrade xenobiotics in pure cultures but few studies focus on their performance under bacterial stress in real wastewaters. This study investigated mutual interactions in co-cultures of Pleurotus ostreatus and activated sludge microbes in batch reactors and different culture media. Under the bacterial stress an increase in the dye decolorization efficiency (95 vs. 77.1 %) and a 2-fold elevated laccase activity (156.7 vs. 78.4 Ul(-1)) were observed in fungal-bacterial cultures compared to pure P. ostreatus despite a limited growth of bacteria in mixed cultures. According to 16S-rDNA analyses, P. ostreatus was able to alter the structure of bacterial communities. In malt extract-glucose medium the fungus inhibited growth of planktonic bacteria and prevented shifts in bacterial utilization of potential C-sources. A model bacterium, Rhodococcus erythropolis responded to fungal metabolites by down regulation of uridylate kinase and acetyl-CoA synthetase. PMID:27116960

  19. Stratification structure of polysaccharides and proteins in activated sludge with different aeration in membrane bioreactor.

    PubMed

    Zhang, Haifeng; Yu, Haihuan; Zhang, Lanhe; Song, Lianfa

    2015-09-01

    The effect of distribution pattern of polysaccharides (PS) and proteins (PN) in activated sludge (AS) stratification with different aeration rates on membrane fouling and rejection efficiency were investigated. During high aeration, PN and PS concentrations increased in supernatant, the dominant fraction (84% of PN and 73% of PS) was small molecules (<1 kDa). Less slime and loose bound extracellular polymeric substances (LB-EPS), more tight bound EPS (TB-EPS) were observed compared with low aeration. The decrease in PN/PS ratio and Ca(2+) concentration within EPS deteriorated AS flocculation ability. At slow trans-membrane pressure (TMP) rise stage, fouling rate under high aeration was 41% lower than low aeration due to lower PN within EPS outer. Low PS rejection rate (about 23%) leaded to higher PS in effluent at this stage. High PS rejection rate (about 94%) at rapid TMP rise stage resulted in about 2.2-time higher fouling rate than that low aeration. PMID:26056777

  20. Removal of a broad range of surfactants from municipal wastewater--comparison between membrane bioreactor and conventional activated sludge treatment.

    PubMed

    González, Susana; Petrovic, Mira; Barceló, Damià

    2007-02-01

    Elimination of alkylphenol ethoxylates (APEO) and their degradation products (alkylphenols and alkylphenoxy carboxylates), as well as linear alkylbenzene sulfonates (LAS) and coconut diethanol amides (CDEA), was studied in a pilot plant membrane bioreactor (MBR) working in parallel to a full-scale wastewater treatment plant (WWTP) using conventional activated sludge (CAS). In the CAS system 87% of parent long ethoxy chain NPEOs were eliminated, but their decomposition yielded persistent acidic and neutral metabolites which were poorly removed. The elimination of short ethoxy chain NPEOs (NP(1)EO and NP(2)EO) averaged 50%, whereas nonylphenoxy carboxylates (NPECs) showed an increase in concentrations with respect to the ones measured in influent samples. Nonylphenol (NP) was the only nonylphenolic compound efficiently removed (96%) in the CAS treatment. On the other hand, MBR showed good performance in removing nonylphenolic compounds with an overall elimination of 94% for the total pool of NPEO derived compounds (in comparison of 54%-overall elimination in the CAS). The elimination of individual compounds in the MBR was as follows: 97% for parent, long ethoxy chain NPEOs, 90% for short ethoxy chain NPEOs, 73% for NPECs, and 96% for NP. Consequently, the residual concentrations were in the low mug/l level or below it. LAS and CDEA showed similar elimination in the both wastewater treatment systems that were investigated, and no significant differences were observed between the two treatment processes. Nevertheless, for all studied compounds the MBR effluent concentrations were consistently lower and independent of the influent concentrations. Additionally, MBR effluent quality in terms of chemical oxygen demand (COD), NH(4)(+) concentration and total suspended solids (TSS) was always superior to the ones of the CAS and also independent of the influent quality, which demonstrates high potential of MBRs in the treatment of municipal wastewaters. PMID:17123581

  1. Influence of thermal extraction of extracellular polymeric substances on cell integrity in activated sludge and membrane bioreactor samples.

    PubMed

    Antonelli, M; Bialek, K; Teli, A; Citterio, S; Malpei, F

    2011-02-01

    The influence of the soluble microbial products (SMP) and extracellular polymeric substances (EPS) heating extraction method on cell viability was evaluated for each phase of the protocol using epifluorescence microscopy. In addition, the effect of different centrifugation conditions (2700 g at 24 degrees C; 12,000 g at 4 degrees C) was also tested. Sludge samples were collected from a conventional wastewater treatment and a membrane bioreactor (MBR) pilot plant fed in parallel. Results show that different centrifugation parameters do not induce cell membrane damaging. Heating significantly influences membrane integrity; for instance, 75 to 90% of initial viable cells are damaged during this phase, possibly leading to the predominance of protein compared to carbohydrate content. The protein content in EPS is 60 to 88 mg bovine serum albumin/ g volatile suspended solids (VSS); higher values observed in MBR sludge samples are probably attributable to the different characteristics of microbial flocs and process operating parameters. Carbohydrate concentrations are not significantly different regardless of applied procedure and sludge type, and are between 10.4 to 11.6 mg glucose/g VSS. PMID:21449471

  2. The influence of hydrolysis induced biopolymers from recycled aerobic sludge on specific methanogenic activity and sludge filterability in an anaerobic membrane bioreactor.

    PubMed

    Buntner, D; Spanjers, H; van Lier, J B

    2014-03-15

    The objective of the present study was to evaluate the impact of excess aerobic sludge on the specific methanogenic activity (SMA), in order to establish the maximum allowable aerobic sludge loading. In batch tests, different ratios of aerobic sludge to anaerobic inoculum were used, i.e. 0.03, 0.05, 0.10 and 0.15, showing that low ratios led to an increased SMA. However, the ratio 0.15 caused more than 20% SMA decrease. In addition to the SMA tests, the potential influence of biopolymers and extracellular substances, that are generated as a result of excess aerobic sludge hydrolysis, on membrane performance was determined by assessing the fouling potential of the liquid broth, taking into account parameters such as specific resistance to filtration (SRF) and supernatant filterability (SF). Addition of aerobic sludge to the anaerobic biomass resulted in a high membrane fouling potential. The increase in biopolymers could be ascribed to aerobic sludge hydrolysis. A clear positive correlation between the concentration of the colloidal fraction of biopolymer clusters (cBPC) and the SRF was observed and a negative correlation between the cBPC and the SF measured at the end of the above described SMA tests. The latter implies that sludge filtration resistance increases when more aerobic sludge is hydrolyzed, and thus more cBPC is released. During AnMBR operation, proteins significantly contributed to sludge filterability decrease expressed as SRF and SF, whereas the carbohydrate fraction of SMP was of less importance due to low concentrations. On the contrary, carbohydrates seemed to improve filterability and diminish SRF of the sludge. Albeit, cBPC increase caused an increase in mean TMP during the AnMBR operation, confirming that cBPC is positively correlated to membrane fouling. PMID:24284260

  3. Bacterial biodiversity from an anaerobic up flow bioreactor with ANAMMOX activity inoculated with swine sludge

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The present study aimed to identify organisms with ANAMMOX activity in a reactor maintained in a laboratory. Molecular methods as fluorescence in situ hybridization (FISH), polymerase chain reaction (PCR) and cloning of 16S-rDNA genes probing for Planctomycetes were performed. Seventeen clones were ...

  4. Evaluation of the extracellular polymeric substances by confocal laser scanning microscopy in conventional activated sludge and advanced membrane bioreactors treating hospital wastewater.

    PubMed

    Alrhmoun, Mousaab; Carrion, Claire; Casellas, Magali; Dagot, Christophe

    2014-01-01

    Confocal laser scanning microscopy (CLSM) combined with fluorescent viability indicators, was used in this study to investigate the impact of hospital wastewaters on floc structure and composition. In this work, three pilot-scale projects, two membrane bioreactors (MBRs) with a submerged or external membrane bioreactor and a conventional activated sludge, were installed and operated for 65 days. They were fed with an influent sampled directly from the hospital drainage system, which contained micropollutant concentrations ranging from ng/L to mg/L. Samples of flocs were observed using CLSM to characterize the extracellular polymeric substances (EPS) stained with concanavalin A-tetra methylrhodamine and fluorescein isothiocyanate solution and combined with a fluorescent viability indicator (Baclight(®) Bacterial Viability Kit, Molecular Probes), allowing visualization of isolated stained cells in the three-dimensional structure of flocs (damaged or not). The results of CLSM of the sludge composition were compared with classical biochemical analysis of EPS made through a thermal extraction method. The results showed a good relation between these analyses and the statistical treatment of microscopic pictures. PMID:24901624

  5. A new photo-activated sludge system for nitrification by an algal-bacterial consortium in a photo-bioreactor with biomass recycle.

    PubMed

    van der Steen, Peter; Rahsilawati, Kuntarini; Rada-Ariza, Angélica M; Lopez-Vazquez, Carlos M; Lens, Piet N L

    2015-01-01

    Wastewater treatment technologies requiring large areas may be less feasible in urbanizing regions of developing countries. Therefore, a new technology, named photo-activated sludge (PAS), was investigated to combine the advantages of regular activated sludge systems with those of algae ponds for the removal of ammonium. The PAS consisted of a mixed photo-bioreactor, continuously fed with BG-11 medium, adjusted to 66 mgN-NH4⁺/l. The reactor volume was 2 l, hydraulic retention time was 24 hours, with a depth of 8 cm, and continuous illumination at the water surface was 66 μmol PAR/m²/s (photosynthetically active radiation). Reactor effluent passed through a settler and settled biomass was returned to the reactor. A well settling biomass developed, that contained both algae and nitrifiers. Effluent contained 10 mgN-NH4⁺/L and 51 mgN-NOx⁻/L. Using a simplified model, the specific algae growth rate was estimated at about 0.62 day⁻¹, which was within the expected range. For nitrifiers (ammonia oxidizers), the specific growth rate was 0.11 day⁻¹, which was lower than reported for regular activated sludge. The in-situ photo-oxygenation process by algae contributed 82% of the oxygen input, whereas oxygen diffusion through the mixed surface provided the remaining 18%. The foreseen energy savings that a PAS system could achieve warrant further investigations with real wastewater. PMID:26204077

  6. Bacterial response to a continuous long-term exposure of silver nanoparticles at sub-ppm silver concentrations in a membrane bioreactor activated sludge system.

    PubMed

    Zhang, Chiqian; Liang, Zhihua; Hu, Zhiqiang

    2014-03-01

    Silver nanoparticles (nanosilver or AgNPs) have excellent antimicrobial properties. Because of their increasing use, there is a concern about the potential impact of AgNPs in wastewater treatment systems. This study investigated the long-term effects of AgNPs (continuous loading for more than 60 days) on membrane bioreactor (MBR) activated sludge performance. At the influent AgNP concentration of 0.10 mg Ag/L, there was no significant difference in effluent water quality or bacterial activities before and after AgNP exposure. Nitrifying bacterial community structure was relatively stable before and after the long-term AgNP loading. Both ammonia-oxidizing bacteria (AOB) Nitrosomonas spp. and Nitrosospira spp. were present while Nitrospira spp. was the dominant nitrite-oxidizing bacterial species throughout this study. Abundance of silver resistance gene silE in the MBR, however, increased by 50-fold 41 days after the AgNP exposure, and then decreased with continuous AgNP exposure. The long-term nanosilver exposure did not change the membrane fouling rate although extracellular polymeric substances (EPS) concentration increased significantly after nanosilver dosing. The results suggest that AgNPs at the influent concentrations of 0.10 mg/L and below have almost no impact on activated sludge wastewater treatment performance, as activated sludge can effectively reduce nanosilver toxicity by adsorbing or precipitating AgNPs and silver ions (Ag(+)) released from the dissolution of AgNPs. PMID:24210505

  7. Standardized application of yeast bioluminescent reporters as endocrine disruptor screen for comparative analysis of wastewater effluents from membrane bioreactor and traditional activated sludge.

    PubMed

    Wang, Jun; Eldridge, Melanie; Menn, Fu-min; Dykes, Todd; Sayler, Gary

    2015-12-01

    A standardized protocol is demonstrated for bioluminescent strains Saccharomyces cerevisiae BLYES, BLYAS and BLYR as high-throughput screening tools to monitor the estrogenic, androgenic and toxic potencies in wastewater. The sensitivity and reproducibility of the assay in wastewater monitoring was evaluated for 7 day semi-continuous batch reactor using activated sludge with hormones spiked raw sewage. Yeast bioluminescent assay successfully captured the rapid removal of estrogenic and androgenic activities in the bioreactors, and demonstrated rapid response (≤4 h) with good reproducibility. This standardized protocol was then applied in a 12 months monitoring of the effluent of a WWTP located at Powell, TN, USA featuring parallel-operated full-scale membrane bioreactor (MBR) and traditional activated sludge (TAS) treatment. Monitoring results showed that estrogenic activity was persistent in all TAS and most MBR effluent samples, while residual androgenic activity was non-detectable throughout the monitored period. The estrogenic equivalents (EEQ) in TAS effluent ranged from 21.61 ng/L to 0.04 pg/L and averaged 3.25 ng/L. The EEQ in MBR effluent ranged from 2.88 ng/L to 0.0134 pg/L and averaged ~10 fold less (0.32 ng/L) than TAS. Despite the large temporal variation, MBR effluent EEQ was consistently lower than TAS on any given sampling date. Most MBR effluent samples also exhibited less cytotoxicity than TAS. Further analysis did not demonstrate significant correlation between effluent EEQ level and WWTP operational parameters including MLSS, SRT, HRT and BOD. PMID:26471181

  8. Important operational parameters of membrane bioreactor-sludge disintegration (MBR-SD) system for zero excess sludge production.

    PubMed

    Yoon, Seong-Hoon

    2003-04-01

    In order to prevent excess sludge production during wastewater treatment, a membrane bioreactor-sludge disintegration (MBR-SD) system has been introduced, where the disintegrated sludge is recycled to the bioreactor as a feed solution. In this study, a mathematical model was developed by incorporating a sludge disintegration term into the conventional activated sludge model and the relationships among the operational parameters were investigated. A new definition of F/M ratio for the MBR-SD system was suggested to evaluate the actual organic loading rate. The actual F/M ratio was expected to be much higher than the apparent F/M ratio in MBR-SD. The kinetic parameters concerning the biodegradability of organics hardly affect the system performance. Instead, sludge solubilization ratio (alpha) in the SD process and particulate hydrolysis rate constant (k(h)) in biological reaction determine the sludge disintegration number (SDN), which is related with the overall economics of the MBR-SD system. Under reasonable alpha and k(h) values, SDN would range between 3 and 5 which means the amount of sludge required to be disintegrated would be 3-5 times higher for preventing a particular amount of sludge production. Finally, normalized sludge disintegration rate (q/V) which is needed to maintain a certain level of MLSS in the MBR-SD system was calculated as a function of F/V ratio. PMID:12697235

  9. Activated Sludge.

    ERIC Educational Resources Information Center

    Saunders, F. Michael

    1978-01-01

    Presents the 1978 literature review of wastewater treatment. This review covers: (1) activated sludge process; (2) process control; (3) oxygen uptake and transfer; (4) phosphorus removal; (5) nitrification; (6) industrial wastewater; and (7) aerobic digestion. A list of 136 references is also presented. (HM)

  10. Fate of aromatic hydrocarbons in Italian municipal wastewater systems: an overview of wastewater treatment using conventional activated-sludge processes (CASP) and membrane bioreactors (MBRs).

    PubMed

    Fatone, Francesco; Di Fabio, Silvia; Bolzonella, David; Cecchi, Franco

    2011-01-01

    We studied the occurrence, removal, and fate of 16 polycyclic aromatic hydrocarbons (PAHs) and 23 volatile organic compounds (VOCs) in Italian municipal wastewater treatment systems in terms of their common contents and forms, and their apparent and actual removal in both conventional activated-sludge processes (CASP) and membrane bioreactors (MBRs). We studied five representative full-scale CASP treatment plants (design capacities of 12,000 to 700,000 population-equivalent), three of which included MBR systems (one full-scale and two pilot-scale) operating in parallel with the conventional systems. We studied the solid-liquid partitioning and fates of these substances using both conventional samples and a novel membrane-equipped automatic sampler. Among the VOCs, toluene, ethylbenzene, xylenes, styrene, 1,2,4-trimethylbenzene, and 4-chlorotoluene were ubiquitous, whereas naphthalene, acenaphthene, fluorene, and phenanthrene were the most common PAHs. Both PAHs and aromatic VOCs had removal efficiencies of 40-60% in the headworks, even in plants without primary sedimentation. Mainly due to volatilization, aromatic VOCs had comparable removal efficiencies in CASP and MBRs, even for different sludge ages. MBRs did not enhance the retention of PAHs sorbed to suspended particulates compared with CASPs. On the other hand, the specific daily accumulation of PAHs in the MBR's activated sludge decreased logarithmically with increasing sludge age, indicating enhanced biodegradation of PAHs. The PAH and aromatic VOC contents in the final effluent are not a major driver for widespread municipal adoption of MBRs, but MBRs may enhance the biodegradation of PAHs and their removal from the environment. PMID:20804998

  11. Comparative study of emerging micropollutants removal by aerobic activated sludge of large laboratory-scale membrane bioreactors and sequencing batch reactors under low-temperature conditions.

    PubMed

    Kruglova, Antonina; Kråkström, Matilda; Riska, Mats; Mikola, Anna; Rantanen, Pirjo; Vahala, Riku; Kronberg, Leif

    2016-08-01

    Four emerging micropollutants ibuprofen, diclofenac, estrone (E1) and 17α-ethinylestradiol (EE2) were studied in large laboratory-scale wastewater treatment plants (WWTPs) with high nitrifying activity. Activated sludge (AS) with sludge retention times (SRTs) of 12days and 14days in sequencing batch reactors (SBRs) and 30days, 60days and 90days in membrane bioreactors (MBRs) were examined at 8°C and 12°C. Concentrations of pharmaceuticals and their main metabolites were analysed in liquid phase and solid phase of AS by liquid chromatography-tandem mass spectrometry (LC-MS/MS). A remarkable amount of contaminants were detected in solids of AS, meaning the accumulation of micropollutants in bacterial cells. The biodegradation rate constants (Kbiol) were affected by SRT and temperature. MBR with a 90-day SRT showed the best results of removal. Conventional SBR process was inefficient at 8°C showing Kbiol values lower than 0.5lgSS(-1)d(-1) for studied micropollutants. PMID:27128192

  12. Activated sludge filterability improvement by nitrifying bacteria abundance regulation in an adsorption membrane bioreactor (Ad-MBR).

    PubMed

    Sun, Fei-yun; Lv, Xiao-mei; Li, Ji; Peng, Zhong-yi; Li, Pu; Shao, Ming-fei

    2014-10-01

    Autotrophic nitrifying bacteria have its intrinsic properties including low EPS production, dense colonial structure and slow-growth rate, favoring the sludge filterability improvement. An adsorption-MBR (Ad-MBR) was developed to enrich nitrifier abundance in the MBR chamber by inlet C/N regulation, and its possible positive effect on sludge filterability and underlying mechanisms were investigated. By DNA extraction, PCR amplification and Illumina high-throughput pyrosequencing, the abundance of nitrifying bacteria was accurately quantified. More than 8.29% nitrifier abundance was achieved in Ad-MBR sludge, which was above three times of that in conventional MBR. Regulated C/N ratio and thereafter nitrifier abundance enrichment improved sludge filterability by altering sludge mixture and its supernatant properties, reflected by a good sludge settleability, a low supernatant viscosity and turbidity, a low supernatant organic substances concentration, and a small amount of strong hydrophobic fractional components, thus to profoundly improve sludge filterability and decelerate membrane fouling. PMID:25146315

  13. The investigation of different pollutants and operation processes on sludge toxicity in sequencing batch bioreactors.

    PubMed

    Chen, Xiurong; Zhao, Jianguo; Bao, Linlin; Wang, Lu; Zhang, Yuying

    2016-08-01

    The influence of different target pollutants and operation modes in sequencing batch bioreactors (SBRs) on sludge toxicity was compared in this study. Sludge toxicity was characterized by the inhibiting luminosity through using luminescent bacterium Photobacterium phosphoreum (P. phosphoreum) during either gradual acclimation or impaction processes with synthetic wastewater containing high-strength bisphenol A (BPA) or N, N-dimethylformamide (DMF). When the activated sludge was first acclimated with either 120 mg/L DMF or 20 mg/L BPA, and then respectively increased to 200 mg/L DMF and 40 mg/L BPA it was defined as gradual acclimation process, whereas when the activated sludge was, respectively, injected with 200 mg/L DMF and 40 mg/L BPA directly it was defined as impaction process. Results showed that the toxicity of the impacted sludge was greater than that of the gradual acclimated sludge, especially in the initial stage before 10 d. Activated sludge treating BPA synthetic wastewater exhibited higher toxicity due to the more inhibition of BPA to sludge activity compared to that of DMF. The proteomics analysis indicated that the stress responses of activated sludge to DMF and BPA stimulation were both significant. In turn, the secretions from two kinds of sludge under stress conditions contributed to sludge toxicity. PMID:26914341

  14. FACTORS AFFECTING COMPOSTING OF MUNICIPAL SLUDGE IN A BIOREACTOR

    EPA Science Inventory

    The research was initiated to determine the feasibility of composting municipal sludge in an aerated tank bioreactor system and to develop baseline data for the rational operation and design of enclosed reactor composting systems. A variety of conditions was tested and various mi...

  15. Metabolism studies of diclofenac and clofibric acid in activated sludge bioreactors using liquid chromatography with quadrupole - time-of-flight mass spectrometry

    NASA Astrophysics Data System (ADS)

    Kosjek, Tina; Heath, Ester; Pérez, Sandra; Petrović, Mira; Barceló, Damia

    2009-06-01

    SummaryTwo environmentally relevant pharmaceuticals, the non-steroidal antiinflammatory drug, diclofenac and the pharmacologically active metabolite of several serum triglyceride-lowering pharmaceuticals, clofibric acid, were subjected to microbiological transformation in activated sludge bioreactors, and the production of breakdown products was studied. For separation, detection and identification of diclofenac's metabolites a UPLC-(+)ESI-QqToF-MS was employed, which enabled the detection of seven transformation products of diclofenac, all including the diagnostic fragment ion at m/z 214. The chemical structure of one metabolite was proposed, which was produced by dehydratation and lactame formation. Further investigations revealed additional two metabolites, which were isomeric structures with an elemental composition C 13H 10NCl 2; however, their chemical structures were not completely resolved. In addition, another biodegradation product showed an abundant fragment ion at m/z 295, the elemental composition of which was confirmed with a high degree of certainty as C 14H 11NO 2Cl 2. The biodegradation of clofibric acid revealed one metabolite in the (-)ESI-QqToF chromatogram, 4-chlorophenol, which is known to exhibit a higher toxicity than the parent compound. This study confirms that further research is needed on the formation of stable metabolites both during wastewater treatment and in the environment. It also highlights the need for parallel toxicity testing. In addition, this study suggests that more needs to be known about the environmental fate of pharmaceuticals so that we are able to provide a comprehensive risk assessment.

  16. Treatment of a submerged anaerobic membrane bioreactor (SAnMBR) effluent by an activated sludge system: the role of sulphide and thiosulphate in the process.

    PubMed

    Sánchez-Ramírez, J E; Seco, A; Ferrer, J; Bouzas, A; García-Usach, F

    2015-01-01

    This work studies the use of a well-known and spread activated sludge system (UCT configuration) to treat the effluent of a submerged anaerobic membrane bioreactor (SAnMBR) treating domestic wastewater. Ammonia, phosphate, dissolved methane and sulphide concentrations in the SAnMBR effluent were around 55 mg NH4-N L(-1), 7 mg PO4-P L(-1), 30 mg non-methane biodegradable COD L(-1), and 105 mg S(2-) L(-1) respectively. The results showed a nitrification inhibition caused by the presence of sulphur compounds at any of the solids retention time (SRT) studied (15, 20 and 25 days). This inhibition could be overcome increasing the hydraulic retention time (HRT) from 13 to 26 h. Among the sulphur compounds, sulphide was identified as the substance which caused the nitrification inhibition. When the nitrification was well established, removal rates of nitrogen and phosphorus of 56% and 45% were reached respectively. The sulphide present in the influent was completely oxidised to sulphate, contributing this oxidation to the denitrification process. Moreover, the presence of methanotrophic bacteria, detected by FISH technique, could also contribute to the denitrification. PMID:25239686

  17. Effects of sludge retention times on reactivity of effluent dissolved organic matter for trihalomethane formation in hybrid powdered activated carbon membrane bioreactors.

    PubMed

    Ma, Defang; Gao, Baoyu; Xia, Chufan; Wang, Yan; Yue, Qinyan; Li, Qian

    2014-08-01

    In this study, real municipal wastewater intended for reuse was treated by two identical hybrid PAC/MBRs (membrane bioreactors with powdered activated carbon addition), which were operated at sludge retention times (SRTs) of 30 and 180 days, respectively. In order to investigate the effects of SRT on trihalomethane (THM) formation in chlorinated PAC/MBR effluents, characteristics and THM formation reactivity of effluent dissolved organic matter (EfOM) at different SRTs were examined. PAC/MBR-180 had higher level of EfOM, which contained less simple aromatic proteins and exhibited lower specific UV absorbance. EfOM with molecular weight <5 kDa from PAC/MBR-30 (23%) was lower than PAC/MBR-180 (26%). About 50% of EfOM from PAC/MBR-30 was hydrophobic acids, which was higher than that from PAC/MBR-180 (about 36%). EfOM at SRT 180 days exhibited higher hydrophilicity. Prolonging SRT greatly reduced THM formation reactivity of EfOM, but increased the formation of bromine-containing species during chlorination of PAC/MBR effluents. PMID:24929809

  18. Comparison of two treatments for the removal of selected organic micropollutants and bulk organic matter: conventional activated sludge followed by ultrafiltration versus membrane bioreactor.

    PubMed

    Sahar, E; Ernst, M; Godehardt, M; Hein, A; Herr, J; Kazner, C; Melin, T; Cikurel, H; Aharoni, A; Messalem, R; Brenner, A; Jekel, M

    2011-01-01

    The potential of membrane bioreactor (MBR) systems to remove organic micropollutants was investigated at different scales, operational conditions, and locations. The effluent quality of the MBR system was compared with that of a plant combining conventional activated sludge (CAS) followed by ultrafiltration (UF). The MBR and CAS-UF systems were operated and tested in parallel. An MBR pilot plant in Israel was operated for over a year at a mixed liquor suspended solids (MLSS) range of 2.8-10.6 g/L. The MBR achieved removal rates comparable to those of a CAS-UF plant at the Tel-Aviv wastewater treatment plant (WWTP) for macrolide antibiotics such as roxythromycin, clarithromycin, and erythromycin and slightly higher removal rates than the CAS-UF for sulfonamides. A laboratory scale MBR unit in Berlin - at an MLSS of 6-9 g/L - showed better removal rates for macrolide antibiotics, trimethoprim, and 5-tolyltriazole compared to the CAS process of the Ruhleben sewage treatment plant (STP) in Berlin when both were fed with identical quality raw wastewater. The Berlin CAS exhibited significantly better benzotriazole removal and slightly better sulfamethoxazole and 4-tolyltriazole removal than its MBR counterpart. Pilot MBR tests (MLSS of 12 g/L) in Aachen, Germany, showed that operating flux significantly affected the resulting membrane fouling rate, but the removal rates of dissolved organic matter and of bisphenol A were not affected. PMID:21330721

  19. Two Devices for Removing Sludge From Bioreactor Wastewater

    NASA Technical Reports Server (NTRS)

    Archer, Shivaun; Hitchens, G. DUncan; Jabs, Harry; Cross, Jennifer; Pilkinton, Michelle; Taylor, Michael

    2007-01-01

    Two devices a magnetic separator and a special filter denoted a self-regenerating separator (SRS) have been developed for separating sludge from the stream of wastewater from a bioreactor. These devices were originally intended for use in microgravity, but have also been demonstrated to function in normal Earth gravity. The magnetic separator (see Figure 1) includes a thin-walled nonmagnetic, stainless-steel cylindrical drum that rotates within a cylindrical housing. The wastewater enters the separator through a recirculation inlet, and about 80 percent of the wastewater flow leaves through a recirculation outlet. Inside the drum, a magnet holder positions strong permanent magnets stationary and, except near a recirculation outlet, close to the inner drum surface. To enable magnetic separation, magnetite (a ferromagnetic and magnetically soft iron oxide) powder is mixed into the bioreactor wastewater. The magnetite becomes incorporated into the sludge by condensation, onto the powder particles, of microbe flocks that constitute the sludge. As a result, the magnets inside the drum magnetically attract the sludge onto the outer surface of the drum.

  20. WASTE ACTIVATED SLUDGE PROCESSING

    EPA Science Inventory

    A study was made at pilot scale of a variety of processes for dewatering and stabilization of waste activated sludge from a pure oxygen activated sludge system. Processes evaluated included gravity thickening, dissolved air flotation thickening, basket centrifugation, scroll cent...

  1. Comparison and Analysis of Membrane Fouling between Flocculent Sludge Membrane Bioreactor and Granular Sludge Membrane Bioreactor

    PubMed Central

    Zhi-Qiang, Chen; Jun-Wen, Li; Yi-Hong, Zhang; Xuan, Wang; Bin, Zhang

    2012-01-01

    The goal of this study is to investigate the effect of inoculating granules on reducing membrane fouling. In order to evaluate the differences in performance between flocculent sludge and aerobic granular sludge in membrane reactors (MBRs), two reactors were run in parallel and various parameters related to membrane fouling were measured. The results indicated that specific resistance to the fouling layer was five times greater than that of mixed liquor sludge in the granular MBR. The floc sludge more easily formed a compact layer on the membrane surface, and increased membrane resistance. Specifically, the floc sludge had a higher moisture content, extracellular polymeric substances concentration, and negative surface charge. In contrast, aerobic granules could improve structural integrity and strength, which contributed to the preferable permeate performance. Therefore, inoculating aerobic granules in a MBR presents an effective method of reducing the membrane fouling associated with floc sludge the perspective of from the morphological characteristics of microbial aggregates. PMID:22859954

  2. Performance of anaerobic membrane bioreactor during digestion and thickening of aerobic membrane bioreactor excess sludge.

    PubMed

    Hafuka, Akira; Mimura, Kazuhisa; Ding, Qing; Yamamura, Hiroshi; Satoh, Hisashi; Watanabe, Yoshimasa

    2016-10-01

    In this study, we evaluated the performance of an anaerobic membrane bioreactor in terms of digestion and thickening of excess sludge from an aerobic membrane bioreactor. A digestion reactor equipped with an external polytetrafluoroethylene tubular microfiltration membrane module was operated in semi-batch mode. Solids were concentrated by repeated membrane filtration and sludge feeding, and their concentration reached 25,400mg/L after 92d. A high chemical oxygen demand (COD) removal efficiency, i.e., 98%, was achieved during operation. A hydraulic retention time of 34d and a pulse organic loading rate of 2200mg-COD/(L-reactor) gave a biogas production rate and biogas yield of 1.33L/(reactor d) and 0.08L/g-CODinput, respectively. The external membrane unit worked well without membrane cleaning for 90d. The transmembrane pressure reached 25kPa and the filtration flux decreased by 80% because of membrane fouling after operation for 90d. PMID:27394993

  3. Enhanced sludge properties and distribution study of sludge components in electrically-enhanced membrane bioreactor.

    PubMed

    Giwa, Adewale; Ahmed, Iftikhar; Hasan, Shadi Wajih

    2015-08-15

    This study investigated the impact of electric field on the physicochemical and biological characteristics of sludge wasted from an electrically-enhanced membrane bioreactor treating medium-strength raw wastewater. This method offers a chemical-free electrokinetic technique to enhance sludge properties and remove heavy metals. For example, sludge volume index (SVI), time-to-filter (TTF), mean sludge particle diameter (PSD), viscosity, and oxidation-reduction potential (ORP) of 21.7 mL/g, 7 min, 40.2 μm, 3.22 mPa s, and -4.9 mV were reported, respectively. Also, X-ray fluorescence (XRF) and X-ray diffraction (XRD) analyses provided mechanisms for heavy metal removal so as to establish relevant pathways for nutrient recovery. Furthermore, variations in dissolved oxygen (DO), conductivity, viscosity, ORP, total suspended solids (MLSS), and volatile suspended solids (MLVSS) were interrelated to evaluate the quality of wasted sludge. A pathway study on the transport and chemical distribution of nutrients and metals in sludge showed great potential for metal removal and nutrient recovery. PMID:26048394

  4. Particulate organics degradation and sludge minimization in aerobic, complete SRT bioreactors.

    PubMed

    Amanatidou, Elisavet; Samiotis, Georgios; Trikoilidou, Eleni; Tsikritzis, Lazaros

    2016-05-01

    The study evaluates the assumption that in activated sludge processes and under specific operating conditions, the considered unbiodegradable particulate organic fractions of influent (XU) organic solids and biomass decay residues (cell debris, XE) are degraded. The evaluation was performed by comparing sludge observed yield (Yobs) evolution in two full scale, complete solids retention time (SRT), aerobic bioreactors, to the predictions of two activated sludge models. The results showed that in steady state operating conditions of complete solids retention AS processes very low solids accumulation occur. In these conditions, solids accumulation is slightly affected by kinetic coefficients and significantly affected by XU and XE degradation rates. High endogenous residues degradation rate values of 0.05 d(-1) and 0.02 d(-1) were estimated for the two bioreactors, resulting in low solids accumulation, calculated at 1.6 tons and 3.59 tons per year respectively, of which 1.37 and 0.87 tons were non volatile suspended solids. Depending on WWTP operating conditions the endogenous residues degradation rate is the limiting factor of solids accumulation and consequently for particulate organics degradation. PMID:26971804

  5. Effect of sludge age on simultaneous nitrification and denitrification in membrane bioreactor.

    PubMed

    Hocaoglu, S Murat; Insel, G; Cokgor, E Ubay; Orhon, D

    2011-06-01

    This study evaluated the effect of sludge age on simultaneous nitrification and denitrification in a membrane bioreactor treating black water. A membrane bioreactor with no separate anoxic volume was operated at a sludge age of 20 days under low dissolved oxygen concentration of 0.1-0.2mg/L. Its performance was compared with the period when the sludge age was adjusted to 60 days. Floc size distribution, apparent viscosity, and nitrogen removal differed significantly, together with different biomass concentrations: nitrification was reduced to 40% while denitrification was almost complete. Modelling indicated that both nitrification and denitrification kinetics varied as a function of the sludge age. Calibrated values of half saturation coefficients were reduced when the sludge age was lowered to 20 days. Model simulation confirmed the validity of variable process kinetics for nitrogen removal, specifically set by the selected sludge age. PMID:21507621

  6. Enhanced Lipid and Biodiesel Production from Glucose-Fed Activated Sludge: Kinetics an Microbial Community Analysis

    EPA Science Inventory

    An innovative approach to increase biofuel feedstock lipid yields from municipal sewage sludge via manipulation of carbon:nitrogen (C:N) ratio and glucose loading in activated sludge bioreactors was investigated. Sludge lipid and fatty acid methyl ester (biodiesel) yields (% cel...

  7. RECYCLE AND REUSE OF CHARCOAL MADE FROM EXCESS SLUDGE IN MEMBRANE BIOREACTOR

    NASA Astrophysics Data System (ADS)

    Tran, Tuyet Thi; Shafiquzzaman, Md.; Nakajima, Jun

    Charcoal produced from excess sludge appeared to be useful for removing SMP (soluble microbial products) in MBR (membrane bioreactors) and therefore for reducing membrane fouling. Batch experiments and long-term MBR experiments were performed by using charcoal made of actual excess sludge. In the batch experiments, SMP was removed effectively through charcoal addition. This approach proved especially effective for the removal of carbohydrate. Charcoal would serve as an absorbent and coagulant in SMP removal. High BOD (biochemical oxygen demand) removal efficiencies produced no negative effects on biological activity in the reactors during the long-term MBR experiments involving charcoal addition. The decrease of humic substances and COD (chemical oxygen demand) through charcoal addition suggested that this approach effectively enhanced the performance of activated sludge treatment. A charcoal addition of more than 0.1% in long-term MBR experiments effectively decreased the membrane fouling frequency. The use of charcoal therefore served to mitigate membrane fouling. A decrease in carbohydrate, corresponding to the increase in the mean fouling period, suggested that a charcoal addition of more than 0.1% effectively removed SMP, especially carbohydrate. A charcoal cyclic reuse system is also proposed. This system would involve charcoal production and charcoal addition to MBR.

  8. Filtration Characterization Method as Tool to Assess Membrane Bioreactor Sludge Filterability—The Delft Experience

    PubMed Central

    Lousada-Ferreira, Maria; Krzeminski, Pawel; Geilvoet, Stefan; Moreau, Adrien; Gil, Jose A.; Evenblij, Herman; van Lier, Jules B.; van der Graaf, Jaap H. J. M.

    2014-01-01

    Prevention and removal of fouling is often the most energy intensive process in Membrane Bioreactors (MBRs), responsible for 40% to 50% of the total specific energy consumed in submerged MBRs. In the past decade, methods were developed to quantify and qualify fouling, aiming to support optimization in MBR operation. Therefore, there is a need for an evaluation of the lessons learned and how to proceed. In this article, five different methods for measuring MBR activated sludge filterability and critical flux are described, commented and evaluated. Both parameters characterize the fouling potential in full-scale MBRs. The article focuses on the Delft Filtration Characterization method (DFCm) as a convenient tool to characterize sludge properties, namely on data processing, accuracy, reproducibility, reliability, and applicability, defining the boundaries of the DFCm. Significant progress was made concerning fouling measurements in particular by using straight forward approaches focusing on the applicability of the obtained results. Nevertheless, a fouling measurement method is still to be defined which is capable of being unequivocal, concerning the fouling parameters definitions; practical and simple, in terms of set-up and operation; broad and useful, in terms of obtained results. A step forward would be the standardization of the aforementioned method to assess the sludge filtration quality. PMID:24957174

  9. Filtration characterization method as tool to assess membrane bioreactor sludge filterability-the delft experience.

    PubMed

    Lousada-Ferreira, Maria; Krzeminski, Pawel; Geilvoet, Stefan; Moreau, Adrien; Gil, Jose A; Evenblij, Herman; van Lier, Jules B; van der Graaf, Jaap H J M

    2014-01-01

    Prevention and removal of fouling is often the most energy intensive process in Membrane Bioreactors (MBRs), responsible for 40% to 50% of the total specific energy consumed in submerged MBRs. In the past decade, methods were developed to quantify and qualify fouling, aiming to support optimization in MBR operation. Therefore, there is a need for an evaluation of the lessons learned and how to proceed. In this article, five different methods for measuring MBR activated sludge filterability and critical flux are described, commented and evaluated. Both parameters characterize the fouling potential in full-scale MBRs. The article focuses on the Delft Filtration Characterization method (DFCm) as a convenient tool to characterize sludge properties, namely on data processing, accuracy, reproducibility, reliability, and applicability, defining the boundaries of the DFCm. Significant progress was made concerning fouling measurements in particular by using straight forward approaches focusing on the applicability of the obtained results. Nevertheless, a fouling measurement method is still to be defined which is capable of being unequivocal, concerning the fouling parameters definitions; practical and simple, in terms of set-up and operation; broad and useful, in terms of obtained results. A step forward would be the standardization of the aforementioned method to assess the sludge filtration quality. PMID:24957174

  10. Rheological behaviors of anaerobic granular sludge in a spiral symmetry stream anaerobic bioreactor.

    PubMed

    Chen, Xiaoguang; Dai, Ruobin; Xiang, Xinyi; Ma, Chengyu; Li, Gang; Hu, Tao; Xu, Zhengqi; Abdelgadir, Awad

    2015-01-01

    The rheological behaviors of the anaerobic granular sludge (AGS) in a spiral symmetry stream anaerobic bioreactor (SSSAB) were investigated. Shear-thinning behavior, thixotropic behavior, concentration-viscosity behavior and temperature-viscosity behavior were evaluated based on the constitutive equation of the AGS. The results indicated that the Herschel-Bulkley model was able to adequately describe the constitutive relation of AGS in the SSSAB. The AGS also showed shear-thinning behavior as well as thixotropic behavior. The critical shear rate and network strength of the AGS were 61.8 s(-1) and 497.0 W m(-3), respectively. The relationship between the apparent viscosity and the sludge concentration was illustrated and explained by the Woodcock formula. The relationship between apparent viscosity of the AGS and temperature could be modeled using the Arrhenius equation. The AGS was significantly thermo-sensitive and its mean energy of activation was 14.640 kJ mol(-1). Notably, it was necessary to consider such behaviors in the hydrodynamic modeling of SSSAB in which shear condition, sludge concentration and temperature were in non-uniform distribution. PMID:26247766

  11. The EPS characteristics of sludge in an aerobic granule membrane bioreactor.

    PubMed

    Xuan, Wang; Bin, Zhang; Zhiqiang, Shen; Zhigang, Qiu; Zhaoli, Chen; Min, Jin; Junwen, Li; Jingfeng, Wang

    2010-11-01

    The relationship between extracellular polymerase substances (EPS) and sludge characteristic were investigated by extraction and analysis of EPS in different size biomass and membrane fouling in an aerobic granule membrane bioreactor (GMBR). The results indicated that the contents of EPS, polysaccharides and proteins in large granules (particle diameter, d>0.45mm) were significantly lower than that in small granules (d<0.45mm) and flocculent sludge. In addition, the content of EPS in membrane fouling was more than that in suspended biomass. For flocculent sludge, the sedimentation and filtering performance decreased markedly as increasing EPS content. However, for granular sludge, there was no significant correlation between EPS content and sludge characteristics. Furthermore, application of aerobic granule can improve sludge filtering properties and delay the process of membrane fouling, as a result of better morphological structure and lower EPS content. PMID:20566286

  12. Can aquatic worms enhance methane production from waste activated sludge?

    PubMed

    Serrano, Antonio; Hendrickx, Tim L G; Elissen, Hellen H J; Laarhoven, Bob; Buisman, Cees J N; Temmink, Hardy

    2016-07-01

    Although literature suggests that aquatic worms can help to enhance the methane production from excess activated sludge, clear evidence for this is missing. Therefore, anaerobic digestion tests were performed at 20 and at 30°C with sludge from a high-loaded membrane bioreactor, the aquatic worm Lumbriculus variegatus, feces from these worms and with mixtures of these substrates. A significant synergistic effect of the worms or their feces on methane production from the high-loaded sludge or on its digestion rate was not observed. However, a positive effect on low-loaded activated sludge, which generally has a lower anaerobic biodegradability, cannot be excluded. The results furthermore showed that the high-loaded sludge provides an excellent feed for L. variegatus, which is promising for concepts where worm biomass is considered a resource for technical grade products such as coatings and glues. PMID:26998797

  13. Removal of pharmaceuticals from synthetic wastewater in an aerobic granular sludge membrane bioreactor and determination of the bioreactor microbial diversity.

    PubMed

    Wang, Xiao-Chun; Shen, Ji-Min; Chen, Zhong-Lin; Zhao, Xia; Xu, Hao

    2016-09-01

    Five types of pharmaceuticals and personal care products (PPCPs) substances were selected as pollutants in this study. The effects of the removal of these pollutants and the microbial succession process in a granular sludge membrane bioreactor (GMBR) were investigated. Results showed that wastewater containing PPCPs influenced the performance of granular sludge. The removal of the five PPCPs from the GMBR had different effects. The removal rates of prednisolone, norfloxacin and naproxen reached 98.5, 87.8 and 84 %, respectively. The degradation effect in the GMBR system was relatively lower for sulphamethoxazole and ibuprofen, with removal efficiency rates of 79.8 and 63.3 %, respectively. Furthermore, the microbial community structure and diversity variation of the GMBR were analysed via high-throughput sequencing technology. The results indicated the structural and functional succession of the microbial community based on the GMBR process. The results indicate the key features of bacteria with an important role in drug degradation. PMID:27234140

  14. Filamentous sludge bulking control by nano zero-valent iron in activated sludge treatment systems.

    PubMed

    Xu, Shengnan; Sun, Minghao; Zhang, Chiqian; Surampalli, Rao; Hu, Zhiqiang

    2014-12-01

    Sludge bulking causes loss of biomass in the effluent and deterioration of effluent water quality. This study explored the use of nano zero-valent iron (NZVI with an average particle size of 55 ± 11 nm) for sludge bulking control. In two Modified Ludzack-Ettinger (MLE) activated sludge treatment systems, a single dose of NZVI at the final concentration of 100 mg Fe per L in the mixed liquor reduced the number of filamentous bacteria Type 021N by 2-3 log units (a reduction of 99.9 and 96.7% in MLE tank #1 and #2, respectively). The side effect of the use of NZVI depended on sludge bulking conditions and biomass concentration. In the system with sludge bulking and significant sludge loss (average biomass concentration of 1022 ± 159 COD mg per L or at the ratio of 0.098 g Fe per g biomass COD), the use of NZVI increased effluent COD, NH4(+)-N and NO2(-)-N concentrations, as also evident with the loss of nitrifying populations and nitrifying activities resulting in more than 40 days to have the full recovery of the activated sludge system. In contrast, in the system with the early stages of bulking and the biomass concentration of 1799 ± 113 COD mg per L (at the ratio of 0.056 g Fe per g biomass COD), the effluent water quality and overall bioreactor performance were only slightly affected for a few days. PMID:25386669

  15. Innovative anaerobic/upflow sludge blanket filtration bioreactor for phosphorus removal from wastewater.

    PubMed

    Khorsandi, H; Movahedyan, H; Bina, B; Farrokhzadeh, H

    2011-04-01

    Phosphorus is the key element to remove from aquatic environments to limit the growth of aquatic plants and algae and, thus, to control eutrophication. Because the upflow sludge blanket filtratio' (USBF) process, without addition of metal salts, entails low efficiency for phosphorus removal, we added an anaerobic reactor to the USBF bioreactor in order to promote the simultaneous removal of phosphorus and nitrogen from wastewater. The results revealed that the anaerobic/USBF bioreactor had a phosphorus removal efficiency up to 86%, with a sludge retention time (SRT) of 10 days, a hydraulic retention time (HRT) of 24 hours and an optimum COD/N/P ratio of 100/5/1. This ratio also improved the compaction quality of the sludge blanket in the USBF clarifier. The average specific phosphate uptake rate in the aerobic zone and the average specific phosphate release rate in the anaerobic reactor were 0.014 mg PO4-P removed/(g VSS x min) and 0.0525 mg PO4-P released/(g VSS x min), respectively. Secondary phosphorus release in the USBF clarifier was heightened with increasing HRT. Hence, the optimum total HRT can be selected between 16 and 24 hours based on effluent quality. Effluent phosphorus of about 1 mg/L was provided for wastewater with the COD/N/P ratio of 100/5/1 at the sludge age of 10 days and total HRT of 16 hours. This study illustrated that the anaerobic/USBF bioreactor at the optimum operational conditions can be an effective process for phosphorus removal from municipal wastewater. PMID:21877530

  16. The shift of the microbial community in activated sludge with calcium treatment and its implication to sludge settleability.

    PubMed

    Ye, Chengchen; Yang, Xinping; Zhao, Fang-Jie; Ren, Lifei

    2016-05-01

    The sludge settleability is of prime importance for the activated sludge process. The effect of calcium ion on the biological performance of sludge was investigated in a lab-scale activated sludge system with varying Ca(2+) concentration. Results indicated that addition of 150mg/L Ca(2+) to the influent significantly improved the settling characteristics and metabolic reactivity of activated sludge in the bioreactors. Analyses using denaturing gradient gel electrophoresis (DGGE) and 16S rRNA sequencing showed that a significant difference in the presence of certain bacterial groups between the sludge systems with 150mg/L Ca(2+) and those with 0-100mg/L Ca(2+) addition. Ca(2+) also increased the production of the extracellular polymeric substance (EPS) and facilitated the development of microbial cluster in the bioreactor. Study showed that an addition of 150mg/L Ca(2+) to the influent provides a simple approach to improve the settling properties of activated sludge and maintain high pollutant removal efficiency. PMID:26868150

  17. Integrated fixed-biofilm activated sludge reactor as a powerful tool to enrich anammox biofilm and granular sludge.

    PubMed

    Zhang, Liang; Liu, Miaomiao; Zhang, Shujun; Yang, Yandong; Peng, Yongzhen

    2015-12-01

    A pilot-scale activated sludge bioreactor was filled with immobile carrier to treat high ammonium wastewater. Autotrophic nitrogen elimination occurred rapidly by inoculating nitrifying activated sludge and anammox biofilm. As the ammonium loading rate increased, nitrogen removal rate of 1.2kgNm(-3)d(-1) was obtained with the removal efficiency of 80%. Activated sludge diameter distribution profiles presented two peak values, indicating simultaneous existence of flocculent and granular sludge. Red granular sludge was observed in the reactor. Furthermore, the results of morphological and molecular analysis showed that the characteristics of granular sludge were similar to that of biofilm, while much different from the flocculent sludge. It was assumed granular sludge was formed through the continuous growth and detachment of anammox biofilm. The mechanism of granular sludge formation was discussed and the procedure model was proposed. According to the experimental results, the integrated fixed-biofilm activated sludge reactor provided an alternative to nitrogen removal based on anammox. PMID:25842299

  18. Isolation of estrogen-degrading bacteria from an activated sludge bioreactor treating swine waste, including a strain that converts estrone to β-estradiol.

    PubMed

    Isabelle, Martine; Villemur, Richard; Juteau, Pierre; Lépine, François

    2011-07-01

    An estrogen-degrading bacterial consortium from a swine wastewater biotreatment was enriched in the presence of low concentrations (1 mg/L) of estrone (E1), 17β-estradiol (βE2), and equol (EQO) as sole carbon sources. The consortium removed 99% ± 1% of these three estrogens in 48 h. Estrogen removal occurred even in the presence of an ammonia monooxygenase inhibitor, suggesting that nitrifiers are not involved. Five strains showing estrogen-metabolizing activity were isolated from the consortium on mineral agar medium with estrogens as sole carbon source. They are related to four genera ( Methylobacterium (strain MI6.1R), Ochrobactrum (strains MI6.1B and MI9.3), Pseudomonas (strain MI14.1), and Mycobacterium (strain MI21.2)) distributed among three classes (Alphaproteobacteria, Gammaproteobacteria, and Actinobacteria). Depending on the culture medium, strains MI6.1B, MI9.3, MI14.1, and MI21.2 partially transform βE2 into E1, whereas Methylobacterium sp. strain MI6.1R reduces E1 into βE2 under aerobic conditions, in contrast with the usually observed conversion of βE2 into E1. Since βE2 is a more potent endocrine disruptor than E1, it means that the presence of Methylobacterium sp. strain MI6.1R (or other bacteria with the same E1-reducing activity) in a treatment could transiently increase the estrogenicity of the effluent. MI6.1R can also reduce the ketone group of 16-ketoestradiol, a hydroxylated analog of E1. All βE2 and E1 transformation activities were constitutive, and many of them are favoured in a rich medium than a medium containing no other carbon source. None of the isolated strains could degrade EQO. PMID:21770814

  19. Study of aerobic granular sludge stability in a continuous-flow membrane bioreactor.

    PubMed

    Corsino, S F; Campo, R; Di Bella, G; Torregrossa, M; Viviani, G

    2016-01-01

    A granular continuous-flow membrane bioreactor with a novel hydrodynamic configuration was developed to evaluate the stability of aerobic granular sludge (AGS). Under continuous-flow operation (Period I), AGS rapidly lost their structural integrity resulting in loose and fluffy microbial aggregates in which filamentous bacteria were dominant. The intermittent feeding (Period II) allowed obtaining the succession of feast and famine conditions that favored the increase in AGS stability. Although no further breakage occurred, the formation of new granules was very limited, owing to the absence of the hydraulic selection pressure. These results noted the necessity to ensure, on the one hand the succession of feast/famine conditions, and on the other, the hydraulic selection pressure that allows flocculent sludge washout. This preliminary study shows that the proposed configuration could meet the first aspect; in contrast, biomass selection needs to be improved. PMID:26526094

  20. Influence of influent wastewater communities on temporal variation of activated sludge communities.

    PubMed

    Lee, Sang-Hoon; Kang, Hyun-Jin; Park, Hee-Deung

    2015-04-15

    Continuously feeding influent wastewater containing diverse bacterial species to a wastewater treatment activated sludge bioreactor may influence the activated sludge bacterial community temporal dynamics. To explore this possibility, this study tracked influent wastewater and activated sludge bacterial communities by pyrosequencing 16S rRNA genes from four full-scale wastewater treatment plants over a 9-month period. The activated sludge communities showed significantly higher richness and evenness than the influent wastewater communities. Furthermore, the two communities were different in composition and temporal dynamics. These results demonstrate that the impact of the influent wastewater communities on the activated sludge communities was weak. Nevertheless, 4.3-9.3% of the operational taxonomic units (OTUs) detected in the activated sludge were shared with the influent wastewater, implying contribution from influent wastewater communities to some extent. However, the relative OTU abundance of the influent wastewater was not maintained in the activated sludge communities (i.e., weak neutral assembly). In addition, the variability of the communities of the shared OTUs was moderately correlated with abiotic factors imposed to the bioreactors. Taken together, temporal dynamics of activated sludge communities appear to be predominantly explained by species sorting processes in response to influent wastewater communities. PMID:25655320

  1. Effect of low dosages of powdered activated carbon on membrane bioreactor performance.

    PubMed

    Remy, Maxime; Temmink, Hardy; Rulkens, Wim

    2012-01-01

    Previous research has demonstrated that powdered activated carbon (PAC), when applied at very low dosages and long SRTs, reduces membrane fouling in membrane bioreactors (MBRs). This effect was related to the formation of stronger sludge flocs, which are less sensitive to shear. In this contribution the long-term effect of PAC addition was studied by running two parallel MBRs on sewage. To one of these, PAC was dosed and a lower fouling tendency of the sludge was verified, with a 70% longer sustainable filtration time. Low PAC dosages showed additional advantages with regard to oxygen transfer and dewaterability, which may provide savings on operational costs. PMID:22339033

  2. Protein extraction from activated sludge.

    PubMed

    Denecke, M

    2006-01-01

    Two methods for the separation of protein originating from activated sludge were compared. In one method, the total protein was isolated out of the activated sludge (crude extract). These samples included all dissolved proteins originating from the bacterial cells and biofilm made up of extracellular polymeric substances (EPS). Every time polyacrylamide gel electrophoresis (PAGE) was done, the protein bands from samples of crude extract were covered by polymeric substances including carbohydrates, uronic acids or humic compounds. Using the immunoblot technique it was possible to demonstrate the presence of the heat shock protein HSP70 in crude extracts of activated sludge. The comparison of protein fingerprints required that clear and distinct bands appear on the PAGE analysis. To this end, a procedure to separates bacterial cells from the EPS was developed. Bacterial cells were separated by incubation with EDTA and subsequent filtration. The isolated cells were directly incubated in a sample buffer. PMID:16898150

  3. Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues currently being cultured in rotating bioreactors by investigators

  4. Influence of membrane surface roughness on interfacial interactions with sludge flocs in a submerged membrane bioreactor.

    PubMed

    Zhao, Leihong; Shen, Liguo; He, Yiming; Hong, Huachang; Lin, Hongjun

    2015-05-15

    In this study, the interfacial interactions between sludge flocs and a rough membrane surface in a submerged membrane bioreactor were investigated. Models describing these interfacial interactions were firstly proposed based on the surface element integration (SEI) method. Surface properties of sludge flocs and membrane were experimentally determined to simulate the models through composite Simpson's rule. It was found that, roughness on membrane surface significantly decreased interaction strength, which enabled the sludge flocs to more easily attach on and detach from the rough membrane surface. Further analysis showed that the value of total interaction energy increased with asperity radius, while the strength of total interaction energy decreased with asperity height. Results also demonstrated that increase in floc size would significantly decrease the attractive specific total interaction with rough membrane surface. It was revealed that there existed a critical asperity radius above which the total interaction energy in certain separation distance coverage was continuously repulsive, facilitating membrane fouling control in MBRs. This study demonstrated the possibility to mitigate membrane fouling by "tailoring" membrane surface roughness. PMID:25660708

  5. Cost-effective treatment of organic sludges in a high rate bioreactor

    SciTech Connect

    Dhuldhoya, N.; Lemen, J.; Martin, B.; Myers, J.

    1996-12-31

    The design and pilot testing of a deep fixed bed/attached growth high rate bioreactor (HRB) for treatment and disposal of refinery oily sludges and biosolids are described. The HRB technology is being jointly developed by Texaco Inc. and Stone & Webster Engineering Corporation to allow for the processing of refinery oily sludges, biosolids, and contaminated soils. A key feature of the technology is its integral combination of dewatering, landfarming, and digestion operations. In essence, the technology operates as a combination of landfarm, aerobic digester, and trickling filter for semi-solids/sludges. The system provides biological degradation of wastes, and features optimal air, water and/or solids recycling, and easy of maintenance. The technology is covered by three separate patents and is particularly applicable at facilities where regulations, climatic conditions, and/or land availability limit the use of conventional land-based units. This paper reviews current and proposed regulations pertaining to {open_quotes}land-banned{close_quotes} wastes, and presents our experience with regard to design and operation of the prototype unit. 6 refs., 4 figs., 3 tabs.

  6. Characteristics of granular sludge developed in an upflow anaerobic sludge fixed-film bioreactor treating palm oil mill effluent.

    PubMed

    Zinatizadeh, A A L; Mohamed, A R; Mashitah, M D; Abdullah, A Z; Hasnain Isa, M

    2007-08-01

    In the present study, characteristics of the granular sludge (including physical characteristics under stable conditions and process shocks arising from suspended solid overload, soluble organic overload, and high temperature; biological activity; and sludge kinetic evaluation in a batch experiment) developed in an upflow anaerobic sludge blanket fixed-film reactor for palm oil mill effluent (POME) treatment was investigated. The main aim of this work was to provide suitable understanding of POME anaerobic digestion using such a granular sludge reactor, particularly with respect to granule structure at various operating conditions. The morphological changes in granular sludge resulting from various operational conditions was studied using scanning electron microscopy and transmission electron microscopy images. It was shown that the developed granules consisted of densely packed rod- (Methanosaeta-like microorganism; predominant) and cocci- (Methanosarsina) shaped microorganisms. Methanosaeta aggregates functioned as nucleation centers that initiated granule development of POME-degrading granules. Under the suspended solid overload condition, most of the granules were covered with a thin layer of fiberlike suspended solids, so that the granule color changed to brown and the sludge volume index also increased to 24.5 from 12 to 15 mL/g, which caused a large amount of sludge washout. Some of the granules were disintegrated because of an acidified environment, which originated from acidogenesis of high influent organic load (29 g chemical oxygen demand [COD]/L d). At 60 degrees C, the rate of biomass washout increased, as a result of disintegration of the outer layer of the granules. In the biological activity test, approximately 95% COD removal was achieved within 72 hours, with an initial COD removal rate of 3.5 g COD/L d. During POME digestion, 275 mg calcium carbonate/L bicarbonate alkalinity was produced per 1000 mg COD(removed)/ L. A consecutive reaction kinetic

  7. Bifurcation and chaotic in a model for activated sludge reactors

    NASA Astrophysics Data System (ADS)

    El-Marouf, S. A. A.; Bahaa, G. M.

    2015-04-01

    A dynamical model of an activated sludge process system is considered and analyzed. Numerical techniques are used to show when the system exhibits chaos. Three choices of bifurcation parameters produce different pictures of solution behavior in the form of limit cycles, two-torus and chaotic behavior. For some range of the reactor residence time the model exhibits chaotic behavior as well. Practical criteria are also derived for the effects of feed conditions and purge fraction on the dynamic characteristics of the bioreactor model.

  8. Methanogenic activities in anaerobic membrane bioreactors (AnMBR) treating synthetic municipal wastewater.

    PubMed

    Ho, Jaeho; Sung, Shihwu

    2010-04-01

    Two laboratory-scale anaerobic membrane bioreactors, AnMBR 1 and AnMBR 2, were run in parallel at 25 and 15 degrees C, respectively. Total chemical oxygen demand (COD) removal efficiency was more than 95% and 85% for AnMBR 1 and 2, respectively. The COD removal of AnMBR 1 was mostly carried out biologically. However, the physical removal on the membrane surface compensated for the decreased biological removal rate in AnMBR 2. The membrane in AnMBR systems is likely not only to retain all biomass in the reactor, but also complement decreased biological removal efficiency at low temperature by rejecting soluble organics. Specific methanogenic activity (SMA) test was used to investigate the methanogenic activity profiles of suspended and attached sludge in AnMBRs treating synthetic municipal wastewater at 25 and 15 degrees C. The methanogenic activity was 51.8 ml CH(4)/g VSSd on day 1 and eventually increased 27% and reached 65.7 ml CH(4)/g VSSd on day 75 for AnMBR 1. However, the methanogenic activity of AnMBR 2 sludge was lower than that of AnMBR 1. The microbial activity of suspended sludge continuously increased, while that of attached sludge gradually decreased in this study. The methanogenic activity of attached sludge was far lower than that of suspended sludge. The role of attached sludge on the membrane in AnMBRs as a biofilm for biological organic removal was minimal compared to suspended sludge. PMID:20022745

  9. Comparison of bacterial communities of conventional and A-stage activated sludge systems

    PubMed Central

    Gonzalez-Martinez, Alejandro; Rodriguez-Sanchez, Alejandro; Lotti, Tommaso; Garcia-Ruiz, Maria-Jesus; Osorio, Francisco; Gonzalez-Lopez, Jesus; van Loosdrecht, Mark C. M.

    2016-01-01

    The bacterial community structure of 10 different wastewater treatment systems and their influents has been investigated through pyrosequencing, yielding a total of 283486 reads. These bioreactors had different technological configurations: conventional activated sludge (CAS) systems and very highly loaded A-stage systems. A-stage processes are proposed as the first step in an energy producing municipal wastewater treatment process. Pyrosequencing analysis indicated that bacterial community structure of all influents was similar. Also the bacterial community of all CAS bioreactors was similar. Bacterial community structure of A-stage bioreactors showed a more case-specific pattern. A core of genera was consistently found for all influents, all CAS bioreactors and all A-stage bioreactors, respectively, showing that different geographical locations in The Netherlands and Spain did not affect the functional bacterial communities in these technologies. The ecological roles of these bacteria were discussed. Influents and A-stage bioreactors shared several core genera, while none of these were shared with CAS bioreactors communities. This difference is thought to reside in the different operational conditions of the two technologies. This study shows that bacterial community structure of CAS and A-stage bioreactors are mostly driven by solids retention time (SRT) and hydraulic retention time (HRT), as suggested by multivariate redundancy analysis. PMID:26728449

  10. FRUIT CANNERY WASTE ACTIVATED SLUDGE AS A CATTLE FEED INGREDIENT

    EPA Science Inventory

    The feasibility of sludge disposal, from a fruit processing waste activated sludge treatment system, by dewatering and using the dewatered biological sludge solids as cattle feed was evaluated by Snokist Growers at Yakima, Washington. Dewatering of the biological sludge utilizing...

  11. Measuring the activity of heterotrophic microorganism in membrane bioreactor for drinking water treatment.

    PubMed

    Han, Zheng-Shuang; Tian, Jia-Yu; Liang, Heng; Ma, Jun; Yu, Hua-Rong; Li, Kai; Ding, An; Li, Gui-Bai

    2013-02-01

    In order to quantify the activity of heterotrophic microorganism in membrane bioreactor (MBR) for drinking water treatment, biomass respiration potential (BRP) test and 2,3,5-triphenyl tetrazolium chloride-dehydrogenase activity (TTC-DHA) test were introduced and modified. A sludge concentration ratio of 5:1, incubation time of 2h, an incubation temperature that was close to the real operational temperature, and using a mixture of main AOC components as the substrate were adopted as the optimum parameters for determination of DHA in drinking water MBR. A remarkable consistency among BDOC removal, BRP and DHA for assessing biological performance in different MBRs was achieved. Moreover, a significant correlation between the BRP and DHA results of different MBRs was obtained. However, the TTC-DHA test was expected to be inaccurate for quantifying the biomass activity in membrane adsorption bioreactor (MABR), while the BRP test turned out to be still feasible in that case. PMID:23306121

  12. Fate of proteins and carbohydrates in membrane bioreactor operated at high sludge age.

    PubMed

    Hocaoglu, Selda Murat; Orhon, Derin

    2010-01-01

    The paper evaluated the fate of proteins and carbohydrates in the course of substrate removal by membrane bioreactor (MBR), which was used for the biological treatment of black and grey water components of a controlled decentralized residential area. The MBRs were operated at a high sludge age of 60 days to better observe the magnitude of soluble residual products. Both groups were detected in the raw wastewater and represented 15% of the soluble chemical oxygen demand (COD) content for black water and 9% for grey water. Corresponding ratios in the process effluent were significantly increased to 70% and 24% respectively, indicating that both proteins and carbohydrates were likely to be generated as residual soluble microbial products. Residual soluble organics accumulated in the reactor at much higher levels as compared to the effluent due to cake filtration occurring on the surface of the membrane, entrapping fractions larger than 4-8 nm for proteins, and around 14 nm for carbohydrates. Mass balance showed that proteins and carbohydrates accumulated in the reactor were partially removed due to longer retention and possible acclimation of the biomass. The observed removal rate was much lower for carbohydrates compared with proteins. PMID:20560086

  13. Performance of novel sludge-bed anaerobic membrane bioreactor (SB-AnMBR) treating prehydrolysis liquor.

    PubMed

    Kale, Mayur M; Singh, Kripa S

    2014-01-01

    The feasibility of a novel sludge-bed anaerobic membrane bioreactor (SB-AnMBR) configuration for treating a waste stream from a dissolving pulp production industry was evaluated. The waste stream, called prehydrolysis liquor (PHL), is generated after the wood chips are subjected to high temperature steam to remove unwanted hemicelluloses. The PHL with total chemical oxygen demand (COD) of approximately 100 g/L contained mainly sugars, furfural, lignin, and acetic acid. The SB-AnMBR was fed with the PHL at organic loading rates in a range of 0.8 to10 kg-COD/(m(3)·d). The COD removal efficiency of more than 85% and an average rate of methane production of 0.35 m(3)/(kg-COD·d) were observed at each loading rate. No detectable sugars or furfural were present in the treated effluent from SB-AnMBR. Lignin removal varied from 60 to 90%. Flat-sheet membranes performed well with one fouling event during first 400 days of operation. PMID:24569279

  14. Analysis of submerged membrane for a sludge-bed anaerobic membrane bioreactor treating prehydrolysis liquor.

    PubMed

    Kale, Mayur Milan; Singh, Kripa Shankar

    2016-08-01

    An analysis of foulants and the performance of membranes in innovative sludge-bed anaerobic membrane bioreactors (SB-AnMBRs) were evaluated at mesophilic (35°C for approx. 400 days) followed by thermophilic (55°C for approx. 400 days) temperatures while treating the prehydrolysis liquor (PHL) waste stream from a dissolving pulp production plant. The membrane fouling of SB-AnMBR was analyzed for 0.1, 0.15 and 0.2 m(3)/m(2)/d flux conditions. Physico-chemical analyses of the membrane showed that the combination of 5% citric acid, 0.5% NaOCl and 2% NaOH solutions was effective in achieving more than 80% recovery of membrane flux. Chemical characterization of foulants showed that proteins were more predominant in membrane fouling than carbohydrates. Sugars and lignin contribution were negligible as compared to proteins in the total organic carbon content of the foulant. Membrane fouling occurred through a biofilm-dominated process and organic fouling. Combination of cleaning chemicals which included 0.5% NaClO and 2% NaOH solutions was most effective in the removal of the organic foulants. SEM analysis showed the pictorial evolution of the impact of fouling on the pore openings and the effect of cleaning on the membrane surface. PMID:26708166

  15. Disturbance and temporal partitioning of the activated sludge metacommunity.

    PubMed

    Vuono, David C; Benecke, Jan; Henkel, Jochen; Navidi, William C; Cath, Tzahi Y; Munakata-Marr, Junko; Spear, John R; Drewes, Jörg E

    2015-02-01

    The resilience of microbial communities to press disturbances and whether ecosystem function is governed by microbial composition or by the environment have not been empirically tested. To address these issues, a whole-ecosystem manipulation was performed in a full-scale activated sludge wastewater treatment plant. The parameter solids retention time (SRT) was used to manipulate microbial composition, which started at 30 days, then decreased to 12 and 3 days, before operation was restored to starting conditions (30-day SRT). Activated sludge samples were collected throughout the 313-day time series in parallel with bioreactor performance ('ecosystem function'). Bacterial small subunit (SSU) rRNA genes were surveyed from sludge samples resulting in a sequence library of >417,000 SSU rRNA genes. A shift in community composition was observed for 12- and 3-day SRTs. The composition was altered such that r-strategists were enriched in the system during the 3-day SRT, whereas K-strategists were only present at SRTs⩾12 days. This shift corresponded to loss of ecosystem functions (nitrification, denitrification and biological phosphorus removal) for SRTs⩽12 days. Upon return to a 30-day SRT, complete recovery of the bioreactor performance was observed after 54 days despite an incomplete recovery of bacterial diversity. In addition, a different, yet phylogenetically related, community with fewer of its original rare members displaced the pre-disturbance community. Our results support the hypothesis that microbial ecosystems harbor functionally redundant phylotypes with regard to general ecosystem functions (carbon oxidation, nitrification, denitrification and phosphorus accumulation). However, the impacts of decreased rare phylotype membership on ecosystem stability and micropollutant removal remain unknown. PMID:25126758

  16. Disturbance and temporal partitioning of the activated sludge metacommunity

    PubMed Central

    Vuono, David C; Benecke, Jan; Henkel, Jochen; Navidi, William C; Cath, Tzahi Y; Munakata-Marr, Junko; Spear, John R; Drewes, Jörg E

    2015-01-01

    The resilience of microbial communities to press disturbances and whether ecosystem function is governed by microbial composition or by the environment have not been empirically tested. To address these issues, a whole-ecosystem manipulation was performed in a full-scale activated sludge wastewater treatment plant. The parameter solids retention time (SRT) was used to manipulate microbial composition, which started at 30 days, then decreased to 12 and 3 days, before operation was restored to starting conditions (30-day SRT). Activated sludge samples were collected throughout the 313-day time series in parallel with bioreactor performance (‘ecosystem function'). Bacterial small subunit (SSU) rRNA genes were surveyed from sludge samples resulting in a sequence library of >417 000 SSU rRNA genes. A shift in community composition was observed for 12- and 3-day SRTs. The composition was altered such that r-strategists were enriched in the system during the 3-day SRT, whereas K-strategists were only present at SRTs⩾12 days. This shift corresponded to loss of ecosystem functions (nitrification, denitrification and biological phosphorus removal) for SRTs⩽12 days. Upon return to a 30-day SRT, complete recovery of the bioreactor performance was observed after 54 days despite an incomplete recovery of bacterial diversity. In addition, a different, yet phylogenetically related, community with fewer of its original rare members displaced the pre-disturbance community. Our results support the hypothesis that microbial ecosystems harbor functionally redundant phylotypes with regard to general ecosystem functions (carbon oxidation, nitrification, denitrification and phosphorus accumulation). However, the impacts of decreased rare phylotype membership on ecosystem stability and micropollutant removal remain unknown. PMID:25126758

  17. Activated sludge optimization using ATP in pulp and paper industry.

    PubMed

    Bäckman, Göran; Gytel, Ulla

    2015-01-01

    The activated sludge process is an old technology, but still the most commonly used one for treatment of wastewater. Despite the wide spread usage the technology still suffers from instability (Tandoi et al. 2006) and high operating cost. Activated sludge processes often carry a large solids inventory. Managing the total inventory without interference is the key component of the optimization process described in this paper. Use of nutrients is common in pulp and paper effluent treatment. Feeding enough nutrients to support the biomass growth is a delicate balance. Overfeeding or underfeeding of nutrients can result in higher costs. Detrimental substances and toxic components in effluents entering a biological treatment system can cause severe, long lasting disturbances (Hynninen & Ingman 1998; Bergeron & Pelletier 2004). A LumiKem test kit is used to measure biological activity with adenosine triphosphate (ATP) in a pulp and paper mill. ATP data are integrated with other standardized mill parameters. Measurements of active volatile suspended solids based on ATP can be used to quantify the living biomass in the activated sludge process and to ensure that sufficient biomass is present in order to degrade the wastewater constituents entering the process. Information about active biomass will assist in optimizing sludge inventories and feeding of nutrients allowing the living biomass to re-populate to create optimal efficiency. ATP measurements can also be used to alert operators if any components toxic to bacteria are present in wastewater. The bio stress index represents the stress level experienced by the microbiological population. This parameter is very useful in monitoring toxicity in and around bioreactors. Results from the wastewater process optimization and ATP measurements showed that treatment cost could be reduced by approximately 20-30% with fewer disturbances and sustained biological activity compared to the reference period. This was mainly achieved by

  18. Effect of sludge characteristics on membrane fouling during start-up of a tertiary submerged membrane bioreactor.

    PubMed

    Díaz, Oliver; Vera, Luisa; González, Enrique; García, Elisa; Rodríguez-Sevilla, Juan

    2016-05-01

    In membrane bioreactors applied to wastewater treatment, fouling is typically a complex function of sludge characteristics. A pilot-scale tertiary submerged membrane bioreactor (tMBR) was continuously operated for over 200 days to assess the effect of biomass physiological state and environmental stress on process performance. Sludge characteristics were evaluated in terms of suspended solid concentration (MLSS and MLVSS), apparent viscosity, bioflocculation state, filterability, bioactivity, biopolymeric clusters (BPCs) and soluble microbial products. During the initial period of the tMBR start-up, when MLSS was below 3000 mg/L, the biomass was found to be very sensitive to environmental stress by sudden oxygen increase or organic shock loading, resulting in temporary biomass deflocculation and BPC release, and consequently, severe induced membrane fouling. However, at higher MLSS values, low stable biomass growth (0.04 ± 0.002 kg MLVSS/kg COD) was measured, regardless of organic overloading shocks or feeding failures. This period was also characterised by low bioactivity, BPC content and membrane fouling. Statistical analysis showed that BPCs have an important role when compared with other sludge properties as indicators of its fouling potential. PMID:26822213

  19. A comprehensive study into fouling properties of extracellular polymeric substance (EPS) extracted from bulk sludge and cake sludge in a mesophilic anaerobic membrane bioreactor.

    PubMed

    Ding, Yi; Tian, Yu; Li, Zhipeng; Zuo, Wei; Zhang, Jun

    2015-09-01

    This study focused on the fouling behaviors of extracellular polymeric substances (EPS) in a mesophilic anaerobic membrane bioreactor (AnMBR) to obtain the relations of EPS specific constituents with membrane fouling. It was found that for the EPS extracted from bulk sludge, the LB-EPS induced the largest flux decline; however, for EPS extracted from cake sludge, the S-EPS caused the highest flux decline. The preferential rejection fraction by membrane further confirmed that the greater flux decline was exhibited with the higher percent rejection of EPS fractions. The adhesion and cohesion interactions of EPS fractions and membranes could explain the different rejection rates of the EPS components. The structural characteristics analysis indicated that the fouling layers of different EPS fractions with the greater loss of filterability had the smaller porosity. Further investigations demonstrated that these changes could be attributed to the different content of HPO-N in EPS fractions. PMID:26022972

  20. Co-conditioning and dewatering of alum sludge and waste activated sludge.

    PubMed

    Lai, J Y; Liu, J C

    2004-01-01

    Co-conditioning and dewatering behaviors of alum sludge and waste activated sludge were investigated. Two different sludges were mixed at various ratios (2:1; 1:1; 1:2; 1:4) for study. Capillary suction time (CST) and specific resistance to filtration (SRF) were utilized to assess sludge dewaterability. Relatively speaking, waste activated sludge, though of higher solid content, was more difficult to be dewatered than alum sludge. It was found that sludge dewaterability and settlability became better with increasing fraction of alum sludge in the mixed sludge. Dosage required of the cationic polyelectrolyte (KP-201C) for dewatering was reduced as well. It is proposed that alum sludge acts as skeleton builder in the mixed sludge, and renders the mixed sludge more incompressible which is beneficial for sludge dewatering. Implications of the results of the study to the sludge management plan for Taipei City that generates both alum sludge and waste activated sludge at significant amount are also discussed. The current sludge treatment and disposal plan in Metropolitan Taipei could be made more cost-effective. PMID:15580993

  1. ACTIVELY CONTROLLED VORTEX DISPOSAL SYSTEM FOR SLUDGE WASTES

    EPA Science Inventory

    The development of an advanced sludge treatment concept is under way for applications to sludge wastes. The concept integrates primary treatment of sludge in an advanced vortex containment combustor (VCC) with subsequent post treatment in an actively controlled acoustic afterburn...

  2. ACTIVELY CONTROLLED VORTEX DISPOSAL SYSTEM FOR SLUDGE WASTES

    EPA Science Inventory

    The development of an advanced sludge treatment concept is underway for applications to sludge wastes. The concept integrates primary treatment of sludge in an advanced vortex containment combustor (VCC) with subsequent post treatment in an actively controlled acoustic afterburne...

  3. Screening wastewater for toxicity to activated sludge

    SciTech Connect

    Schneider, C.G.

    1987-01-01

    Several toxicity tests were compared to define their utility for prediction of toxicity to activated sludge. The tests included: (1) oxygen uptake rates in batch tests with activated sludge, (2) adenosine triphosphate (ATP) measurements in the same batch tests, (3) Warburg respirometer studies with activated sludge, and (4) a luminescent bacteria test (Microtox/sup TM/). An evaluation of the toxicity tests was made with several toxicants; nickel (II), mercury (II), 2,4-dichlorophenol (DCP) and 4,6-dinitro-o-cresol (DNOC). Because of differences in toxic mechanism, some of the toxicants produced greater toxic effects in some tests than in other tests. The ATP levels decreased significant when uncouplers of oxidative phosphorylation were studied (DCP and DNOC). Several procedures for measuring ATP were investigated and were found to be unsatisfactory when applied to activated sludge. A new method for extraction of ATP, which incorporated a sonic bath and trichloroacetic acid, was developed. The improved ATP method was used in the toxicity tests and for the additional studies. Current practice in environmental engineering relies on volatile suspended solids (VSS) as a measure of active biomass in activated sludge. After an improved ATP procedure was developed, ATP was investigated for estimation of active biomass. The fate of DCP in the toxicity tests was studied and an adsorptive mechanism was proposed that was based on membrane solubility. This mechanism explained the fate of DCP in the toxicity tests and is useful for understanding the fate of DCP in activated sludge.

  4. Performance analysis of a combined system of membrane bioreactor and worm reactor: wastewater treatment, sludge reduction and membrane fouling.

    PubMed

    Tian, Yu; Lu, Yaobin; Li, Zhipeng

    2012-10-01

    A new process that combined a membrane bioreactor (S-MBR) and a novel worm reactor was proposed in this study. The combined system indicated excellent sludge reduction efficiency, wastewater treatment performance and membrane permeability. The sludge reduction percentage of the combined system was about 1.9 times higher than that of the conventional MBR. The chemical oxygen demand (COD) discharge rate in the combined system was only one fourth of that in the conventional MBR, indicating that the COD was removed more thoroughly. Low extracellular polymeric substances level (60-75 μg/mg), low filamentous bacteria level, narrow floc size distribution (distribution spread index of 0.91) and high roundness (0.80 ± 0.10) were observed in the S-MBR sludge. Deposited by this modified sludge, a fouling layer with smaller thickness, larger porosity and less proteins and polysaccharides accumulation was formed in the S-MBR, demonstrating that the combined system was able to alleviate membrane fouling. PMID:22858483

  5. Removal of steroid estrogens from municipal wastewater in a pilot scale expanded granular sludge blanket reactor and anaerobic membrane bioreactor.

    PubMed

    Ito, Ayumi; Mensah, Lawson; Cartmell, Elise; Lester, John N

    2016-01-01

    Anaerobic treatment of municipal wastewater offers the prospect of a new paradigm by reducing aeration costs and minimizing sludge production. It has been successfully applied in warm climates, but does not always achieve the desired outcomes in temperate climates at the biochemical oxygen demand (BOD) values of municipal crude wastewater. Recently the concept of 'fortification' has been proposed to increase organic strength and has been demonstrated at the laboratory and pilot scale treating municipal wastewater at temperatures of 10-17°C. The process treats a proportion of the flow anaerobically by combining it with primary sludge from the residual flow and then polishing it to a high effluent standard aerobically. Energy consumption is reduced as is sludge production. However, no new treatment process is viable if it only addresses the problems of traditional pollutants (suspended solids - SS, BOD, nitrogen - N and phosphorus - P); it must also treat hazardous substances. This study compared three potential municipal anaerobic treatment regimes, crude wastewater in an expanded granular sludge blanket (EGSB) reactor, fortified crude wastewater in an EGSB and crude wastewater in an anaerobic membrane bioreactor. The benefits of fortification were demonstrated for the removal of SS, BOD, N and P. These three systems were further challenged with the removal of steroid estrogens at environmental concentrations from natural indigenous sources. All three systems removed these compounds to a significant degree, confirming that estrogen removal is not restricted to highly aerobic autotrophs, or aerobic heterotrophs, but is also a faculty of anaerobic bacteria. PMID:26212345

  6. HYDRAULIC CHARACTERISTICS OF ACTIVATED SLUDGE SECONDARY CLARIFIERS

    EPA Science Inventory

    This study documented the hydraulic characteristics of typical activated sludge clarifiers. Modifications to the clarifier structures were made in an attempt to improve clarifier hydraulic characteristics and performance. Innovative fluorometric dye tracer studies were used to ob...

  7. Activated Sludge. Student Manual. Biological Treatment Process Control.

    ERIC Educational Resources Information Center

    Boe, Owen K.; Klopping, Paul H.

    This student manual contains the textual material for a seven-lesson unit on activated sludge. Topic areas addressed in the lessons include: (1) activated sludge concepts and components (including aeration tanks, aeration systems, clarifiers, and sludge pumping systems); (2) activated sludge variations and modes; (3) biological nature of activated…

  8. Formation of distinct soluble microbial products by activated sludge: kinetic analysis and quantitative determination.

    PubMed

    Ni, Bing-Jie; Fang, Fang; Xie, Wen-Ming; Xu, Juan; Yu, Han-Qing

    2012-02-01

    Soluble microbial products (SMP) released by microorganisms in bioreactors are classified into two distinct groups according to their different chemical and degradation kinetics: utilization-associated products (UAP) and biomass-associated products (BAP). SMP are responsible for effluent chemical oxygen demand or for membrane fouling of membrane bioreactor. Here an effective and convenient approach, other than the complicated chemical methods or complex models, is developed to quantify the formation of UAP and BAP together with their kinetics in activated sludge process. In this approach, an integrated substrate utilization equation is developed and used to determine UAP and their production kinetics. On the basis of total SMP measurements, BAP formation is determined with an integrated BAP formation equation. The fraction of substrate electrons diverted to UAP, and the content of BAP derived from biomass can then be calculated. Dynamic quantification data are obtained for UAP and BAP separately and conveniently. The obtained kinetic parameters are found to be reasonable as they are generally bounded and comparable to the literature values. The validity of this approach is confirmed by independent SMP production tests in six different activated sludge systems, which demonstrates its applicability in a wide range of engineered system regarding SMP production. This work provides a widely applied approach to determine the formation of UAP and BAP conveniently, which may offer engineers with basis to optimize bioreactor operation to avoid a high effluent soluble organics from SMP or SMP-based membrane fouling in membrane bioreactors. PMID:22185635

  9. Evaluation of activated sludge for biodegradation of propylene glycol as an aircraft deicing fluid.

    PubMed

    Delorit, Justin D; Racz, LeeAnn

    2014-04-01

    Aircraft deicing fluid used at airport facilities is often collected for treatment or disposal in order to prevent serious ecological threats to nearby surface waters. This study investigated lab scale degradation of propylene glycol, the active ingredient in a common aircraft deicing fluid, by way of a laboratory-scale sequencing batch reactor containing municipal waste water treatment facility activated sludge performing simultaneous organic carbon oxidation and nitrification. The ability of activated sludge to remove propylene glycol was evaluated by studying the biodegradation and sorption characteristics of propylene glycol in an activated sludge medium. The results indicate sorption may play a role in the fate of propylene glycol in AS, and the heterotrophic bacteria readily degrade this compound. Therefore, a field deployable bioreactor may be appropriate for use in flight line applications. PMID:24851333

  10. Activated Sludge and other Aerobic Suspended Culture Processes.

    PubMed

    Li, Chunying; Wei, Li; Chang, Chein-Chi; Zhang, Yuhua; Wei, Dong

    2016-10-01

    This is a literature review for the year 2015 and contains information specifically associated with suspended growth processes including activated sludge, upflow anaerobic sludge blanket, and sequencing batch reactors. The review encompasses modeling and kinetics, nutrient removal, system design and operation. Compared to past reviews, many topics show increase in activity in 2015. These include, fate and effect of xenobiotics, industrial wastes treatment with sludge, and pretreatment for the activated sludge. These topics are referred to the degradation of constituents in activated sludge. Other sections include population dynamics, process microbiology give an insight into the activated sludge. The subsection in industrial wastes: converting sewage sludge into biogases was also mentioned. PMID:27620082

  11. A modified oxic-settling-anaerobic activated sludge process using gravity thickening for excess sludge reduction

    NASA Astrophysics Data System (ADS)

    Wang, Jun; Li, Shi-Yu; Jiang, Feng; Wu, Ke; Liu, Guang-Li; Lu, Hui; Chen, Guang-Hao

    2015-09-01

    Oxic-settling-anaerobic process (OSA) was known as a cost-effective way to reduce the excess sludge production with simple upgrade of conventional activated sludge process (CAS). A low oxidation-reduction potential (ORP) level was the key factor to sludge decay and lysis in the sludge holding tank of the OSA process. However, the ORP control with nitrogen purge or chemical dosing in the OSA process would induce extra expense and complicate the operation. Hence, in this study, a sludge holding tank using gravity thickening was applied to OSA process to reduce the excess sludge production without any ORP control. Results showed that the modified OSA process not only reduced the excess sludge production effectively but also improved the sludge settleability without affected the treatment capacity. The reduction of the excess sludge production in the modified OSA process resulted from interactions among lots of factors. The key element of the process was the gravity thickening sludge holding tank.

  12. A modified oxic-settling-anaerobic activated sludge process using gravity thickening for excess sludge reduction

    PubMed Central

    Wang, Jun; Li, Shi-Yu; Jiang, Feng; Wu, Ke; Liu, Guang-Li; Lu, Hui; Chen, Guang-Hao

    2015-01-01

    Oxic-settling-anaerobic process (OSA) was known as a cost-effective way to reduce the excess sludge production with simple upgrade of conventional activated sludge process (CAS). A low oxidation-reduction potential (ORP) level was the key factor to sludge decay and lysis in the sludge holding tank of the OSA process. However, the ORP control with nitrogen purge or chemical dosing in the OSA process would induce extra expense and complicate the operation. Hence, in this study, a sludge holding tank using gravity thickening was applied to OSA process to reduce the excess sludge production without any ORP control. Results showed that the modified OSA process not only reduced the excess sludge production effectively but also improved the sludge settleability without affected the treatment capacity. The reduction of the excess sludge production in the modified OSA process resulted from interactions among lots of factors. The key element of the process was the gravity thickening sludge holding tank. PMID:26350761

  13. Prediction of the effect of fine grit on the MLVSS/MLSS ratio of activated sludge.

    PubMed

    Fan, Jianping; Ji, Fangying; Xu, Xiaoyi; Wang, Ying; Yan, Dachao; Xu, Xuan; Chen, Qingkong; Xiong, Jingzhong; He, Qiang

    2015-08-01

    This paper investigated the suspension properties of fine grit with different particle sizes in a bioreactor and developed a model to predict its effect on the ratio of mixed liquor volatile suspended solids to the mixed liquor suspended solids (MLVSS/MLSS) of activated sludge. The experimental results revealed that a smaller particle size corresponds to a larger suspension ratio, defined as the proportion of fine grit brought in by influent that is suspended in the activated sludge, and a smaller MLVSS/MLSS ratio. The model demonstrated that the effect of fine grit on the MLVSS/MLSS ratio is related to the fine grit concentration and chemical oxygen demand in influent and the observed sludge yield. However, fine grit has no influence on the activity of microorganisms. Wastewater treatment plants (WWTPs) can adjust MLSS based on the MLVSS/MLSS ratio to ensure the stability of MLVSS, which can achieve the stable operation of WWTPs. PMID:25919937

  14. The effect of activated carbon addition on membrane bioreactor processes for wastewater treatment and reclamation - A critical review.

    PubMed

    Skouteris, George; Saroj, Devendra; Melidis, Paraschos; Hai, Faisal I; Ouki, Sabèha

    2015-06-01

    This review concentrates on the effect of activated carbon (AC) addition to membrane bioreactors (MBRs) treating wastewaters. Use of AC-assisted MBRs combines adsorption, biodegradation and membrane filtration. This can lead to advanced removal of recalcitrant pollutants and mitigation of membrane fouling. The relative contribution of adsorption and biodegradation to overall removal achieved by an AC-assisted MBR process can vary, and "biological AC" may not fully develop due to competition of target pollutants with bulk organics in wastewater. Thus periodic replenishment of spent AC is necessary. Sludge retention time (SRT) governs the frequency of spent AC withdrawal and addition of fresh AC, and is an important parameter that significantly influences the performance of AC-assisted MBRs. Of utmost importance is AC dosage because AC overdose may aggravate membrane fouling, increase sludge viscosity, impair mass transfer and reduce sludge dewaterability. PMID:25801795

  15. Impact of sludge cation distribution pattern on its filterability in membrane bioreactor.

    PubMed

    Zhang, Haifeng; Wang, Zhongping; Zhang, Lanhe; Song, Lianfa

    2014-11-01

    The distributions of cations of various valences (Na(+), Ca(2+) and Fe(3+)) in the outer layers of extracellular polymeric substances (EPSs) to pellet have a significant impact on the stratification structure of polysaccharides (PS) or proteins (PN) in activated sludge. Comparison with the control showed that the monovalent Na(+) reduced flocculability slightly (about 9.75%), whereas Ca(2+) and Fe(3+) increased flocculability significantly. The modified fouling index (MFI) had a significant correlation with PN in the supernatant (rp=0.8593), slime (rp=0.7218) and loosely bound EPS (LB, rp=0.8012). However, it had a moderate correlation with PS in supernatant (rp=0.5842), and weak correlation to slime (rp=0.3785) or LB (rp=0.3219). There was an ignored correlation with PN or PS in the tightly bound EPS (TB) or pellet. The lower amount of PN or PS in the supernatant would have positive impact on improving the activated sludge filterability. PMID:25181695

  16. Measurement of glutathione in activated sludges.

    PubMed

    Dziurla, M A; Leroy, P; Strünkmann, G W; Salhi, M; Lee, D U; Camacho, P; Heinz, V; Müller, J A; Paul, E; Ginestet, Ph; Audic, J M; Block, J C

    2004-01-01

    Thermal, electric, mechanical or oxidative stress seem a promising way to reduce the production of excess activated sludge during biological wastewater treatment. However, the adaptation and the resistance of the sludge microbial ecosystem to stress conditions is a major question as it may definitively limit the effect of some treatments. Defence mechanisms developed by aerobic organisms, in particular, in response to oxidative stress involve various antioxidant activities and compounds such as glutathione. An HPLC method was developed for measuring reduced and total glutathione (GSH and GSHt) in perchloric acid sludge extracts. The method was sensitive, highly specific and validated for linearity, precision and recovery. Considering the extraction yield and the oxidation of GSH during extract storage, the measured GSH concentration was estimated to represent 60% of the GSH content from activated sludges. GSHt ranged from 0.32 to 3.34micromolg(-1) volatile solids and the GSH/GSHt ratio ranged from 32% to 91%. Measurements performed on sludges stressed in precise conditions selected to reach a reduction of sludge production showed a decrease of GSH and GSHt concentrations with thermal, mechanical, electric and ozone stress. PMID:14630122

  17. Complete solids retention activated sludge process.

    PubMed

    Amanatidou, E; Samiotis, G; Trikoilidou, E; Pekridis, G; Tsikritzis, L

    2016-01-01

    In a slaughterhouse's full-scale extended aeration activated sludge wastewater treatment plant (WWTP), operating under complete solids retention time, the evolution of mixed liquor suspended solids (MLSS) and mixed liquor volatile suspended solids (MLVSS) concentration, food to micro-organisms ratio (F/M) and substrate utilization rate (SUR) were studied for over a year. Biomass growth phases in correlation to sludge biological and morphological characteristics were studied. Three distinguished growth phases were observed during the 425 days of monitoring. The imposed operational conditions led the process to extended biomass starvation conditions, minimum F/M, minimum SUR and predator species growth. MLSS and MLVSS reached a stabilization phase (plateau phase) where almost zero sludge accumulation was observed. The concept of degradation of the considered non-biodegradable particulate compounds in influent and in biomass (cell debris) was also studied. Comparison of evolution of observed sludge yields (Yobs) in the WWTP with Yobs predictions by activated sludge models verified the degradation concept for the considered non-biodegradable compounds. Control of the sedimentation process was achieved, by predicting the solids loading rate critical point using state point analysis and stirred/unstirred settling velocity tests and by applying a high return activated sludge rate. The nitrogen gas related sedimentation problems were taken into consideration. PMID:27003077

  18. Optimization of membrane bioreactors by the addition of powdered activated carbon.

    PubMed

    Ng, Choon Aun; Sun, Darren; Bashir, Mohammed J K; Wai, Soon Han; Wong, Ling Yong; Nisar, Humaira; Wu, Bing; Fane, Anthony G

    2013-06-01

    It was found that with replenishment, powdered activated carbon (PAC) in the membrane bioreactor (MBR) would develop biologically activated carbon (BAC) which could enhance filtration performance of a conventional MBR. This paper addresses two issues (i) effect of PAC size on MBR (BAC) performance; and (ii) effect of sludge retention time (SRT) on the MBR performance with and without PAC. To interpret the trends, particle/floc size, concentration of mixed liquor suspended solid (MLSS), total organic carbon (TOC), short-term filtration properties and transmembrane pressure (TMP) versus time are measured. The results showed improved fouling control with fine, rather than coarse, PAC provided the flux did not exceed the deposition flux for the fine PAC. Without PAC, the longer SRT operation gave lower fouling at modest fluxes. With PAC addition, the shorter SRT gave better fouling control, possibly due to greater replenishment of the fresh PAC. PMID:23612160

  19. Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, Part I: Semi-empirical model development.

    PubMed

    Sen, Dipankar; Randall, Clifford W

    2008-05-01

    Research was undertaken to develop a model for activated sludge, integrated fixed-film activated sludge (IFAS), and moving-bed biofilm reactor (MBBR) systems. The model can operate with up to 12 cells (reactors) in series, with biofilm media incorporated to one or more cells, except the anaerobic cells. The process configuration can be any combination of anaerobic, anoxic, aerobic, post-anoxic with or without supplemental carbon, and reaeration; it can also include any combination of step feed and recycles, including recycles for mixed liquor, return activated sludge, nitrates, and membrane bioreactors. This paper presents the structure of the model. The model embeds a biofilm model into a multicell activated sludge model. The biofilm flux rates for organics, nutrients, and biomass can be computed by two methods--a semi-empirical model of the biofilm that is relatively simpler, or a diffusional model that is computationally intensive. The values of the kinetic parameters for the model were measured using pilot-scale activated sludge, IFAS, and MBBR systems. For the semiempirical version, a series of Monod equations were developed for chemical oxygen demand, ammonium-nitrogen, and oxidized-nitrogen fluxes to the biofilm. Within the equations, a second Monod expression is used to simulate the effect of changes in biofilm thickness and fraction nitrifiers in the biofilm. The biofilm flux model is then linked to the activated sludge model. The diffusional model and the verification of the models are presented in subsequent papers (Sen and Randall, 2008a, 2008b). The model can be used to quantify the amount of media and surface area required to achieve nitrification, identify the best locations for the media, and optimize the dissolved oxygen levels and nitrate recycle rates. Some of the advanced features include the ability to apply different media types and fill fractions in cells; quantify nitrification, denitrification, and biomass production in the biofilm and

  20. Aerobic composting of waste activated sludge: Kinetic analysis for microbiological reaction and oxygen consumption

    SciTech Connect

    Yamada, Y.; Kawase, Y. . E-mail: bckawase@mail.eng.toyo.ac.jp

    2006-07-01

    In order to examine the optimal design and operating parameters, kinetics for microbiological reaction and oxygen consumption in composting of waste activated sludge were quantitatively examined. A series of experiments was conducted to discuss the optimal operating parameters for aerobic composting of waste activated sludge obtained from Kawagoe City Wastewater Treatment Plant (Saitama, Japan) using 4 and 20 L laboratory scale bioreactors. Aeration rate, compositions of compost mixture and height of compost pile were investigated as main design and operating parameters. The optimal aerobic composting of waste activated sludge was found at the aeration rate of 2.0 L/min/kg (initial composting mixture dry weight). A compost pile up to 0.5 m could be operated effectively. A simple model for composting of waste activated sludge in a composting reactor was developed by assuming that a solid phase of compost mixture is well mixed and the kinetics for microbiological reaction is represented by a Monod-type equation. The model predictions could fit the experimental data for decomposition of waste activated sludge with an average deviation of 2.14%. Oxygen consumption during composting was also examined using a simplified model in which the oxygen consumption was represented by a Monod-type equation and the axial distribution of oxygen concentration in the composting pile was described by a plug-flow model. The predictions could satisfactorily simulate the experiment results for the average maximum oxygen consumption rate during aerobic composting with an average deviation of 7.4%.

  1. Enhancement of polyether biodegradation in activated sludge

    SciTech Connect

    Christopher, L.J.

    1993-01-01

    Previous studies in this laboratory showed that pretreatment with Petroleum Chemical Extinguisher[reg sign] (PCE), a C[sub 18] unsaturated fatty acid diester of polyethylene glycol (PEG), enhanced the biodegradation of PEG 1,000 and PEG 1,450 in soil. In this study the ability of PCE and other PEG-fatty acid diesters to enhance biodegradation of PEGs in activated sludge was investigated. Additionally, polyether-fatty acid esters similar to PCE were synthesized and tested to determine how they affected biodegradation of PEGs and other polyethers. Attempts were made to understand the mechanism for enhancement of biodegradation. Carbon-dioxide evolution and thin-layer chromatographic analysis indicated degradation of PEG 1,000, PEG 1,450, and PEG 3,350 in sludge samples which were previously exposed to PCE. Those samples which were not pre-treated with PCE showed no detectable PEG degradation during the two-week study. Preexposure to PCE did not enhance subsequent degradation of PEG 8,000, nor polypropylene glycol (PPG) 1,025. However, pretreatment of sludge with a PPG 1,025-di oleic acid ester promoted PPG 1,205 degradation. Interestingly, microbial populations do not seem to be gaining much biomass or energy from the degradation of PEG-di fatty acid esters or PEGs. When PCE-pretreated sludge samples were given [sup 14]C-PEG 3,350 as substrate, evolution of [sup 14]CO[sub 2] occurred and little (<5%) of the [sup 14]C was assimilated by the microorganisms in the sludge. Futhermore, determinations of ATP content and esterase activity of sludge samples suggested that there was not a substantial increase in biomass as a result of degradation of either PCE or PEGs. PCE preexposure effected an increase in PEG dehydrogenase activity. This increase may be due to induction of enzymes responsible for PEG biodegradation or selection for organisms in the microbial population which are PEG degraders.

  2. Design of nutrient removal activated sludge systems.

    PubMed

    Manga, J; Ferrer, J; Seco, A; Garcia-Usach, F

    2003-01-01

    A mechanistic mathematical model for nutrient and organic matter removal was used to describe the behavior of a nitrification denitrification enhanced biological phosphorus removal (NDEBPR) system. This model was implemented in a user-friendly software DESASS (design and simulation of activated sludge systems). A 484-L pilot plant was operated to verify the model results. The pilot plant was operated for three years over three different sludge ages. The validity of the model was confirmed with data from the pilot plant. Also, the utility of DESASS as a valuable tool for designing NDEBPR systems was confirmed. PMID:12906279

  3. Microbial community structure and pharmaceuticals and personal care products removal in a membrane bioreactor seeded with aerobic granular sludge.

    PubMed

    Xia, Zhao; Xiao-chun, Wang; Zhong-lin, Chen; Hao, Xu; Qing-fang, Zhang

    2015-01-01

    A process involving the use of membrane bioreactor seeded with aerobic granular sludge (GMBR) was applied to the treatment of sewage containing pharmaceuticals and personal care products (PPCPs). The removal effects of five kinds of medicines in the reactor were investigated, and the microbial communities were constructed by polymerase chain reaction and denaturing gradient gel electrophoresis. We also determined the effects of different sludge retention and hydraulic retention times (SRT and HRT, respectively) and influent organic loading on GMBR's efficiency in processing sewage containing PPCPs. The removal effects of the GMBR on five PPCPs varied. Using the GMBR, the removal rates of prednisolone, naproxen and norfloxacin were 98.56, 84.02 and 87.85%, respectively. The removal rates of sulfamethoxazole and ibuprofen were 77.83 and 63.32%, respectively. In the system, PPCP drugs had relatively less effect on microbial diversity. A certain succession was observed in the structural variation of microbial species in the GMBR. Microorganisms that can degrade PPCPs gradually accumulated, and antibiotic-resistant microorganisms, such as Firmicutes sp., Aeromonas sp. and Nitrospira sp., served a key function in the treatment of sewage containing antibiotics. Long SRT and HRT during the GMBR process can facilitate the removal of most PPCPs. The system efficiently removed PPCPs at high influent organic loading. PMID:25099174

  4. DOWNFLOW GRANULAR FILTRATION OF ACTIVATED SLUDGE EFFLUENTS

    EPA Science Inventory

    The performance of downflow granular filters subjected to effluents from activated sludge processes was investigated at the EPA-DC Pilot Plant in Washington, D.C. Several media combinations were investigated, including both single anthracite and dual anthracite-sand configuration...

  5. DENSITY CURRENTS IN ACTIVATED SLUDGE SECONDARY CLARIFIERS

    EPA Science Inventory

    Density currents form in activated sludge secondary clarifiers because the mixed liquor has a density greater than the treated wastewater in the clarifier. This causes the mixed liquor to plunge to the bottom of the clarifier establishing relatively high velocity currents within ...

  6. METALS DISTRIBUTIONS IN ACTIVATED SLUDGE SYSTEMS

    EPA Science Inventory

    This project developed models to predict the distribution of metals in activated sludge system process streams. The data used to develop the models were obtained through extended pilot studies from a previous project. The objectives of the study were to evaluate the effects of wa...

  7. Long-term performance of side-stream deammonification in a continuous flow granular-activated sludge process for nitrogen removal from high ammonium wastewater.

    PubMed

    Rezania, Babak; Mavinic, Donald S; Kelly, Harlan G

    2015-01-01

    An innovative granular sludge deammonification system was incorporated into a conventional-activated sludge process. The process incorporated an internal baffle in the bioreactor for continuous separation of granular biomass from flocculent biomass, which allowed for controlling the solids retention time of flocculent sludge. The process was evaluated for ammonium removal from municipal digested sludge dewatering centrate under various operating conditions lasting over 450 days. The process successfully removed, on average, 90% of the ammonium from centrate at various ammonium loading reaching 1.4 kg/m³d at 20 hours hydraulic retention time. Controlling the retention time of the flocculent biomass and maintaining low nitrite concentration were both found to be effective for nitrite oxidizing bacteria management, resulting in a low nitrate concentration (below 50 mg/L) over a wide range of flocculent biomass concentration in the bioreactor. PMID:25909736

  8. Effects of Organic-Loading-Rate Reduction on Sludge Biomass and Microbial Community in a Deteriorated Pilot-Scale Membrane Bioreactor

    PubMed Central

    Sato, Yuya; Hori, Tomoyuki; Navarro, Ronald R.; Naganawa, Ryuichi; Habe, Hiroshi; Ogata, Atsushi

    2016-01-01

    The effects of a precipitous decrease in the inlet organic loading rate on sludge reductions and the microbial community in a membrane bioreactor were investigated. The sludge biomass was markedly reduced to 47.4% of the initial concentration (approximately 15,000 mg L−1) within 7 d after the organic loading rate was decreased by half (450 to 225 mg chemical oxygen demand L−1 d−1). An analysis of the microbial community structure using high-throughput sequencing revealed an increase in the abundance of facultative predatory bacteria-related operational taxonomic units as well as microorganisms tolerant to environmental stress belonging to the classes Deinococci and Betaproteobacteria. PMID:27431196

  9. Biodegradability of activated sludge organics under anaerobic conditions.

    PubMed

    Ekama, G A; Sötemann, S W; Wentzel, M C

    2007-01-01

    From an experimental and theoretical investigation of the continuity of activated sludge organic (COD) compounds along the link between the fully aerobic or N removal activated sludge and anaerobic digestion unit operations, it was found that the unbiodegradable particulate organics (i) originating from the influent wastewater and (ii) generated by the activated sludge endogenous process, as determined from response of the activated sludge system, are also unbiodegradable under anaerobic digestion conditions. This means that the activated sludge biodegradable organics that can be anaerobically digested can be calculated from the active fraction of the waste activated sludge based on the widely accepted ordinary heterotrophic organism (OHO) endogenous respiration/death regeneration rates and unbiodegradable fraction. This research shows that the mass balances based steady state and dynamic simulation activated sludge, aerobic digestion and anaerobic digestion models provide internally consistent and externally compatible elements that can be coupled to produce plant wide steady state and dynamic simulation WWTP models. PMID:17045327

  10. Activated Sludge and other Aerobic Suspended Culture Processes.

    PubMed

    Wei, Li; Wei, Chao; Chang, Chein-Chi; You, Shao-Hong

    2015-10-01

    This is a literature review for the year 2014 and contains information specifically associated with suspended growth processes including activated sludge and sequencing batch reactors. This review is a subsection of the treatment systems section of the annual literature review. The review encompasses modeling and kinetics, nutrient removal, system design and operation. Compared to past reviews, many topics show increase in activity in 2014. These include, nitrogen and phosphorus control, fate and effect of xenobiotics, industrial wastes treatment, and some new method for the determination of activated sludge. These topics are referred to the degradation of constituents in activated sludge. Other sections include population dynamics, process microbiology of activated sludge, modeling and kinetics. Many of the subsections in the industrial wastes: converting sewage sludge into fuel gases, thermos-alkali hydrolysis of Waste Activated Sludge (WAS), sludge used as H2 S adsorbents were also mentioned in this review. PMID:26420077

  11. Integration of microbial fuel cell techniques into activated sludge wastewater treatment processes to improve nitrogen removal and reduce sludge production.

    PubMed

    Gajaraj, Shashikanth; Hu, Zhiqiang

    2014-12-01

    Bioelectrochemical systems are emerging for wastewater treatment, yet little is known about how well they can be integrated with current wastewater treatment processes. In this bench-scale study, the microbial fuel cell (MFC) technique was incorporated into the Modified Ludzack-Ettinger (MLE) process (phase I) and later with the membrane bioreactor (MBR) process (phase II) to evaluate the performance of MFC assisted wastewater treatment systems (i.e., MLE-MFC and MBR-MFC). There was no significant difference in the effluent NH4(+)-N concentration between the systems integrating MFC and the open circuit controls. The average effluent COD concentration was significantly lower in the MLE-MFC, but it did not change much in the MBR-MFC because of the already low COD concentrations in MBR operation. The MLE-MFC and MBR-MFC systems increased the NO3(-)-N removal efficiencies by 31% (±12%) and 20% (±12%), respectively, and reduced sludge production by 11% and 6%, respectively, while generating an average voltage of 0.13 (±0.03) V in both systems. Analysis of the bacterial specific oxygen uptake rate, the sludge volume index, and ammonia-oxidizing bacterial population (dominated by Nitrosomonas through terminal restriction fragment length polymorphism analysis) indicated that there was no significant difference in sludge activity, settling property, and nitrifying community structure between the MFC assisted systems and the open circuit controls. The results suggest that the wastewater treatment systems could achieve higher effluent water quality and lower sludge production if it is integrated well with MFC techniques. PMID:25014565

  12. Degradation of corticosteroids during activated sludge processing.

    PubMed

    Miyamoto, Aoi; Kitaichi, Yuko; Uchikura, Kazuo

    2014-01-01

    Laboratory tests of the decomposition of corticosteroids during activated sludge processing were investigated. Corticosteroid standards were added to activated sludge, and aliquots were regularly taken for analysis. The corticosteroids were extracted from the samples using a solid-phase extraction method and analyzed LC-MS. Ten types of corticosteroids were measured and roughly classified into three groups: 1) prednisolone, triamcinolone, betamethasone, prednisolone acetate, and hydrocortisone acetate, which decomposed within 4 h; 2) flunisolide, betamethasone valerate, and budesonide of which more than 50% remained after 4 h, but almost all of which decomposed within 24 h; and 3) triamcinolone acetonide, and fluocinolone acetonide of which more than 50% remained after 24 h. The decomposed ratio was correlated with each corticosteroid's Log P, especially groups 2) and 3). PMID:24390495

  13. Activated sludge degradation of adipic acid esters.

    PubMed Central

    Saeger, V W; Kalley, R G; Hicks, O; Tucker, E S; Mieure, J P

    1976-01-01

    The biodegradability of three aliphatic adipic acid diesters and a 1,3-butylene glycol adipic acid polyester was determined in acclimated, activated sludge systems. Rapid primary biodegradation from 67 to 99+% was observed at 3- and 13-mg/liter feed levels for di-n-hexyl adipate, di(2-ethylhexyl) adipate, and di(heptyl, nonyl) adipate in 24 h. When acclimated, activated sludge microorganisms were employed as the seed for two carbon dioxide evolution procedures, greater than 75% of the theoretical carbon dioxide was evolved for the three diesters and the polyester in a 35-day test period. The essentially complete biodegradation observed in these studies suggests that these esters would not persist when exposed to similar mixed microbial populations in the environment. PMID:1275494

  14. Preparation of ferric-activated sludge-based adsorbent from biological sludge for tetracycline removal.

    PubMed

    Yang, Xin; Xu, Guoren; Yu, Huarong; Zhang, Zhao

    2016-07-01

    Ferric activation was novelly used to produce sludge-based adsorbent (SBA) from biological sludge through pyrolysis, and the adsorbents were applied to remove tetracycline from aqueous solution. The pyrolysis temperature and mass ratio (activator/dried sludge) greatly influenced the surface area and pore characteristics of SBA. Ferric activation could promote the porous structure development of adsorbents, and the optimum preparation conditions were pyrolysis temperature 750°C and mass ratio (activator/dried sludge) 0.5. In batch experiments, ferric-activated SBA showed a higher adsorption capacity for tetracycline than non-activated SBA, because the enhanced mesoporous structure favored the diffusion of tetracycline into the pores, the iron oxides and oxygen-containing functional groups in the adsorbents captured tetracycline by surface complexation. The results indicate that ferric activation is an effective approach for preparing adsorbents from biological sludge to remove tetracycline, providing a potential option for waste resource recovery. PMID:27038265

  15. Pilot and full scale applications of sulfur-based autotrophic denitrification process for nitrate removal from activated sludge process effluent.

    PubMed

    Sahinkaya, Erkan; Kilic, Adem; Duygulu, Bahadir

    2014-09-01

    Sulfur-based autotrophic denitrification of nitrified activated sludge process effluent was studied in pilot and full scale column bioreactors. Three identical pilot scale column bioreactors packed with varying sulfur/lime-stone ratios (1/1-3/1) were setup in a local wastewater treatment plant and the performances were compared under varying loading conditions for long-term operation. Complete denitrification was obtained in all pilot bioreactors even at nitrate loading of 10 mg NO3(-)-N/(L.h). When the temperature decreased to 10 °C during the winter time at loading of 18 mg NO3(-)-N/(L.h), denitrification efficiency decreased to 60-70% and the bioreactor with S/L ratio of 1/1 gave slightly better performance. A full scale sulfur-based autotrophic denitrification process with a S/L ratio of 1/1 was set up for the denitrification of an activated sludge process effluent with a flow rate of 40 m(3)/d. Almost complete denitrification was attained with a nitrate loading rate of 6.25 mg NO3(-)-N/(L.h). PMID:24862952

  16. High-rate anaerobic co-digestion of kraft mill fibre sludge and activated sludge by CSTRs with sludge recirculation.

    PubMed

    Ekstrand, Eva-Maria; Karlsson, Marielle; Truong, Xu-Bin; Björn, Annika; Karlsson, Anna; Svensson, Bo H; Ejlertsson, Jörgen

    2016-10-01

    Kraft fibre sludge from the pulp and paper industry constitutes a new, widely available substrate for the biogas production industry, with high methane potential. In this study, anaerobic digestion of kraft fibre sludge was examined by applying continuously stirred tank reactors (CSTR) with sludge recirculation. Two lab-scale reactors (4L) were run for 800days, one on fibre sludge (R1), and the other on fibre sludge and activated sludge (R2). Additions of Mg, K and S stabilized reactor performance. Furthermore, the Ca:Mg ratio was important, and a stable process was achieved at a ratio below 16:1. Foaming was abated by short but frequent mixing. Co-digestion of fibre sludge and activated sludge resulted in more robust conditions, and high-rate operation at stable conditions was achieved at an organic loading rate of 4g volatile solids (VS)L(-1)day(-1), a hydraulic retention time of 4days and a methane production of 230±10NmL per g VS. PMID:27453288

  17. Role of Nocardia in Activated Sludge

    PubMed Central

    Bafghi, Mehdi Fatahi; Yousefi, Nader

    2016-01-01

    Activated sludge process is a biological process that is widely used in the domestic and industrial wastewater treatment in over the world. The foam formation is often reported in wastewater treatment plants which are related to this process. Some operational problems can be created by foaming, such as effluent quality deteriorates, the creation of malodorous, increased time requirements in order to plant maintenance, and in extreme cases, hazardous working conditions resulting from foam spilling out of the aeration basin and as well as increased in operational costs. There are different ways to overcome this problem, such as reduce air flows into the aeration basin, reduction in the grease and oil content of the wastewater, surface and return activated sludge (RAS) chlorination, anoxic and anaerobic selectors, solid retention time (SRT) control and antifoams and organic polymer addition. On the other hand, rapid and accurate identification of the foam causes is in the first step to control bulking and foaming. Foam problem is often created by filamentous bacteria, such as Nocardia and Gordonia species. This bacterium has a role important in activated sludge. PMID:27418874

  18. Role of Nocardia in Activated Sludge.

    PubMed

    Bafghi, Mehdi Fatahi; Yousefi, Nader

    2016-05-01

    Activated sludge process is a biological process that is widely used in the domestic and industrial wastewater treatment in over the world. The foam formation is often reported in wastewater treatment plants which are related to this process. Some operational problems can be created by foaming, such as effluent quality deteriorates, the creation of malodorous, increased time requirements in order to plant maintenance, and in extreme cases, hazardous working conditions resulting from foam spilling out of the aeration basin and as well as increased in operational costs. There are different ways to overcome this problem, such as reduce air flows into the aeration basin, reduction in the grease and oil content of the wastewater, surface and return activated sludge (RAS) chlorination, anoxic and anaerobic selectors, solid retention time (SRT) control and antifoams and organic polymer addition. On the other hand, rapid and accurate identification of the foam causes is in the first step to control bulking and foaming. Foam problem is often created by filamentous bacteria, such as Nocardia and Gordonia species. This bacterium has a role important in activated sludge. PMID:27418874

  19. Evaluating sedimentation problems in activated sludge treatment plants operating at complete sludge retention time.

    PubMed

    Amanatidou, Elisavet; Samiotis, Georgios; Trikoilidou, Eleni; Pekridis, George; Taousanidis, Nikolaos

    2015-02-01

    Zero net sludge growth can be achieved by complete retention of solids in activated sludge wastewater treatment, especially in high strength and biodegradable wastewaters. When increasing the solids retention time, MLSS and MLVSS concentrations reach a plateau phase and observed growth yields values tend to zero (Yobs ≈ 0). In this work, in order to evaluate sedimentation problems arised due to high MLSS concentrations and complete sludge retention operational conditions, two identical innovative slaughterhouse wastewater treatment plants were studied. Measurements of wastewaters' quality characteristics, treatment plant's operational conditions, sludge microscopic analysis and state point analysis were conducted. Results have shown that low COD/Nitrogen ratios increase sludge bulking and flotation phenomena due to accidental denitrification in clarifiers. High return activated sludge rate is essential in complete retention systems as it reduces sludge condensation and hydraulic retention time in the clarifiers. Under certain operational conditions sludge loading rates can greatly exceed literature limit values. The presented methodology is a useful tool for estimation of sedimentation problems encountered in activated sludge wastewater treatment plants with complete retention time. PMID:25463928

  20. Disturbance opens recruitment sites for bacterial colonization in activated sludge.

    PubMed

    Vuono, David C; Munakata-Marr, Junko; Spear, John R; Drewes, Jörg E

    2016-01-01

    Little is known about the role of immigration in shaping bacterial communities or the factors that may dictate success or failure of colonization by bacteria from regional species pools. To address these knowledge gaps, the influence of bacterial colonization into an ecosystem (activated sludge bioreactor) was measured through a disturbance gradient (successive decreases in the parameter solids retention time) relative to stable operational conditions. Through a DNA sequencing approach, we show that the most abundant bacteria within the immigrant community have a greater probability of colonizing the receiving ecosystem, but mostly as low abundance community members. Only during the disturbance do some of these bacterial populations significantly increase in abundance beyond background levels and in few cases become dominant community members post-disturbance. Two mechanisms facilitate the enhanced enrichment of immigrant populations during disturbance: (i) the availability of resources left unconsumed by established species and (ii) the increased availability of niche space for colonizers to establish and displace resident populations. Thus, as a disturbance decreases local diversity, recruitment sites become available to promote colonization. This work advances our understanding of microbial resource management and diversity maintenance in complex ecosystems. PMID:25727891

  1. Performance of aerobic granular sludge in a sequencing batch bioreactor for slaughterhouse wastewater treatment.

    PubMed

    Liu, Yali; Kang, Xiaorong; Li, Xin; Yuan, Yixing

    2015-08-01

    Lab-scale experiment was conducted to investigate the formation and characteristics of aerobic granular sludge for biological nutrient removal of slaughterhouse wastewater. Experimental results showed that removal performances of chemical oxygen demand (COD), ammonia and phosphate were enhanced with sludge granulation, and their removal efficiencies reached 95.1%, 99.3% and 83.5%, respectively. The aerobic granular sludge was matured after 90days cultivation, and protein-like substances were the main components. Simultaneously, the mass ratio of proteins and polysaccharides (PN/PS) was enhanced to 2.5 from 1.7. The granules with particle sizes of 0.6-1.2 and 1.2-1.8mm, accounting for 69.6%, were benefit for the growth of ammonia oxidizing bacteria (AOB) and nitrate oxidizing bacteria (NOB), and corresponding specific oxygen demand rates (SOUR) of AOB and NOB were 31.4 and 23.3mgO2/gMLSSh, respectively. PMID:25777064

  2. Ammonium adsorption in aerobic granular sludge, activated sludge and anammox granules.

    PubMed

    Bassin, J P; Pronk, M; Kraan, R; Kleerebezem, R; van Loosdrecht, M C M

    2011-10-15

    The ammonium adsorption properties of aerobic granular sludge, activated sludge and anammox granules have been investigated. During operation of a pilot-scale aerobic granular sludge reactor, a positive relation between the influent ammonium concentration and the ammonium adsorbed was observed. Aerobic granular sludge exhibited much higher adsorption capacity compared to activated sludge and anammox granules. At an equilibrium ammonium concentration of 30 mg N/L, adsorption obtained with activated sludge and anammox granules was around 0.2 mg NH4-N/g VSS, while aerobic granular sludge from lab- and pilot-scale exhibited an adsorption of 1.7 and 0.9 mg NH4-N/g VSS, respectively. No difference in the ammonium adsorption was observed in lab-scale reactors operated at different temperatures (20 and 30 °C). In a lab-scale reactor fed with saline wastewater, we observed that the amount of ammonium adsorbed considerably decreased when the salt concentration increased. The results indicate that adsorption or better ion exchange of ammonium should be incorporated into models for nitrification/denitrification, certainly when aerobic granular sludge is used. PMID:21840028

  3. Dynamical modelling of an activated sludge system of a petrochemical plant operating at high temperatures.

    PubMed

    Maqueda, M A M; Martinez, Sergio A; Narváez, D; Rodriguez, Miriam G; Aguilar, Ricardo; Herrero, Victor M

    2006-01-01

    The Mexican petrochemical industry, Morelos S.A. de C.V., is one of the biggest and more important petroleum industries in Mexico and Latin America. It has an activated sludge system to treat its wastewater flow, which is approximately 7,000 m3/d. The wastewater contains volatile organic carbon substances classified as toxics. The old surface aeration system was changed for fine bubble diffusers; however, one major drawback of the new aeration system is that the temperature in the bioreactor has increased due to the compression of the air, which at the compressor exit reaches 85 degrees C. This effect results in the temperature in the bioreactor attaining 32 degrees C during the fall, whereas in the spring and summer, the bioreactor temperature reaches higher values than 40 degrees C. The high temperatures reduce the microorganism activity and cause a higher volatilisation rate of volatile compounds, among other effects, which affect the performance of the biological treatment. This work was performed to obtain a better modelling of the wastewater treatment from the petrochemical industry. The model describes the effect of the temperature on the performance of the biological treatment. The model was obtained from tests that were carried out in laboratory reactors with 14 L capacity, which were operated at different temperatures (from 30 to 45 degrees C), with the same wastewater and conditions as the actual system. PMID:16862783

  4. Implications of changes in solids retention time on long term evolution of sludge filterability in anaerobic membrane bioreactors treating high strength industrial wastewater.

    PubMed

    Dereli, Recep Kaan; Grelot, Aurelie; Heffernan, Barry; van der Zee, Frank P; van Lier, Jules B

    2014-08-01

    Long-term experiments were conducted to assess the impact of changing the solids retention time (SRT) on sludge filterability in anaerobic membrane bioreactors (AnMBRs), treating corn-based bioethanol thin stillage. Well established parameters, such as capillary suction time (CST) and specific resistance to filtration (SRF), developed for sludge dewatering, were used to evaluate the SRT effect on sludge filterability. Our results clearly demonstrated that SRT is one of the most important factors influencing sludge filterability in AnMBRs. SRT effects the accumulation of fine particles and solutes, which were found to affect attainable flux and fouling, in reactor broth. A better filterability was observed at a SRT of 20 days compared to elevated SRTs, i.e. 50 days. A clear correlation between sludge filtration characteristics and membrane filtration resistance could not be established especially at short SRTs, whereas many parameters such as total suspended solids (TSS), CST, soluble microbial products (SMP) and supernatant filterability were found to be mutually correlated. Net membrane fluxes between 9 and 13 L m(-2) h(-1) were obtained at 0.5 m s(-1) cross-flow velocity and the long term fouling was controlled by using frequent filtration and backwash cycles. PMID:24769102

  5. A novel rotation generator of hydrodynamic cavitation for waste-activated sludge disintegration.

    PubMed

    Petkovšek, Martin; Mlakar, Matej; Levstek, Marjetka; Stražar, Marjeta; Širok, Brane; Dular, Matevž

    2015-09-01

    The disintegration of raw sludge is very important for enhancement of the biogas production in anaerobic digestion process as it provides easily degradable substrate for microorganisms to perform maximum sludge treatment efficiency and stable digestion of sludge at lower costs. In the present study the disintegration was studied by using a novel rotation generator of hydrodynamic cavitation (RGHC). At the first stage the analysis of hydrodynamics of the RGHC were made with tap water, where the cavitation extent and aggressiveness was evaluated. At the second stage RGHC was used as a tool for pretreatment of a waste-activated sludge (WAS), collected from wastewater treatment plant (WWTP). In case of WAS the disintegration rate was measured, where the soluble chemical oxygen demand (SCOD) and soluble Kjeldahl nitrogen were monitored and microbiological pictures were taken. The SCOD increased from initial 45 mg/L up to 602 mg/L and 12.7% more biogas has been produced by 20 passes through RGHC. The results were obtained on a pilot bioreactor plant, volume of 400 L. PMID:25596776

  6. [Effect of powdered activated carbon on the sludge mixed liquor characteristics and membrane fouling of MBR].

    PubMed

    Li, Shao-Feng; Gao, Yuan

    2011-02-01

    Effect of dosing powder activated carbon (PAC) on the characteristics of the sludge mixed liquor in membrane bioreactor (MBR) was investigated by parallel tests. And the reason that PAC mitigated membrane fouling was also explored. The results showed that PAC could decrease mixture viscosity and increase sludge particle size, which led to less trans-membrane pressure developing. Extracellular polymer substances (EPS) content, sludge specific resistance and cake layer resistance (R(c)) had a good correlation. Adding PAC could decrease EPS concentration, sludge specific resistance and then slow down the increase of R(c), which mitigated membrane fouling. Membrane pore blocking resistance (R(p)) increased exponentially with increasing of the soluble microbial products (SMP) concentration in the supernatant. Dosing PAC reduced the SMP concentration and slowed down the growth rate of R(p), which was helpful to mitigating membrane fouling. R(c) and R(p) increased along with the operation of MBRs and R(c)/R(f) (26.32% -63.16%) was always greater than R(p)/R(f) (7.89% -35.32%) which suggested the R(c) was the main factor in membrane fouling. Moreover, it was also found that controlling of dosing PAC on R(c) was better than it on R(p). PMID:21528575

  7. Comparative effectiveness of membrane bioreactors, conventional secondary treatment, and disinfection to remove microorganisms from municipal wastewaters

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Log removals of bacterial indicators, coliphage, and enteric viruses were studied in three membrane bioreactor activated-sludge (MBR) and two conventional secondary activated-sludge municipal wastewater treatment plants during three disinfection seasons (May–Oct.). In total, 73 regular samples were ...

  8. Correlation between fouling propensity of soluble extracellular polymeric substances and sludge metabolic activity altered by different starvation conditions.

    PubMed

    Wu, Siang Chen; Lee, Chi Mei

    2011-05-01

    Soluble extracellular polymeric substances (EPSs) cause membrane fouling in membrane bioreactors (MBRs), correlated with MBR sludge characteristics. Effects of F/M ratios on the evolution of soluble EPSs, fouling propensity of supernatants, and sludge metabolic activity were measured in this study in a two-period sequencing batch reactor (SBR). The experimental results show that fouling propensity was directly correlated with soluble-EPS concentration and composition. Sludge that had entirely lost active cells by long-term starvation released 64.4 ± 0.9 mg/L of humic acids, which caused a rapid increase in membrane resistance (40.67 ± 2.24 × 10(11) m(-1)) during fouling tests. During short-term starvation, induced by incubation at a normal to low F/M ratio of 0.05 d(-1), sludge can use previously secreted utilization-associated products (UAPs) to maintain endogenous respiration. Therefore, the strategies of accumulating sludge and prolonging sludge retention time in MBRs may create long-term starvation and promote membrane fouling. PMID:21163646

  9. Effect of exo-polysaccharide concentration in the rheological properties and settling ability of activated sludge.

    PubMed

    Akkache, S; Seyssiecq, I; Roche, N

    2013-01-01

    The non-Newtonian properties of activated sludge (AS) suspension lead to transfer limitations (oxygen, substrate...) and operation difficulties in Waste Water Treatment Plants (WWTP). The current approach involves assuming the sludge behaves like water on a rheological point of view, and then oversizing pumping and aeration devices, which represent over 60% of the operating cost in WWTP. The objective of this work is to understand the effect of bioflocculation on the rheological properties and the settling ability of AS suspensions, by means of variations in concentration of exo-cellular polysaccharides. Experiments have been conducted in a 20 L laboratory scale bioreactor at a constant retention time of 20 days and with a total suspended solid concentration between 15 and 20 g L(-1). The bioreactor was fed with a synthetic substrate at a constant mass loading rate of 0.3 kg(DCO) kg(-1)(TSS) d(-1). Our results show that increasing the exo-polysaccharide (EPS) concentration from 10 to 80 mg g(-1)(TSS) leads to an increase in shear-thinning properties of AS. An improvement of the settling ability is also obtained, at least when the EPSs increase from 10 to 45 mg g(-1)(TSS). Above 45 mg g(-1)(TSS) of adsorbed polysaccharides, the settling ability seems to decrease again. PMID:24617058

  10. Microbial dynamics in upflow anaerobic sludge blanket (UASB) bioreactor granules in response to short-term changes in substrate feed

    SciTech Connect

    Kovacik, William P.; Scholten, Johannes C.; Culley, David E.; Hickey, Robert; Zhang, Weiwen; Brockman, Fred J.

    2010-08-01

    The complexity and diversity of the microbial communities in biogranules from an upflow anaerobic sludge blanket (UASB) bioreactor were determined in response to short-term changes in substrate feeds. The reactor was fed simulated brewery wastewater (SBWW) (70% ethanol, 15% acetate, 15% propionate) for 1.5 months (phase 1), acetate / sulfate for 2 months (phase 2), acetate-alone for 3 months (phase 3), and then a return to SBWW for 2 months (phase 4). Performance of the reactor remained relatively stable throughout the experiment as shown by COD removal and gas production. 16S rDNA, methanogen-associated mcrA and sulfate reducer-associated dsrAB genes were PCR amplified, then cloned and sequenced. Sequence analysis of 16S clone libraries showed a relatively simple community composed mainly of the methanogenic Archaea (Methanobacterium and Methanosaeta), members of the Green Non-Sulfur (Chloroflexi) group of Bacteria, followed by fewer numbers of Syntrophobacter, Spirochaeta, Acidobacteria and Cytophaga-related Bacterial sequences. Methanogen-related mcrA clone libraries were dominated throughout by Methanobacter and Methanospirillum related sequences. Although not numerous enough to be detected in our 16S rDNA libraries, sulfate reducers were detected in dsrAB clone libraries, with sequences related to Desulfovibrio and Desulfomonile. Community diversity levels (Shannon-Weiner index) generally decreased for all libraries in response to a change from SBWW to acetate-alone feed. But there was a large transitory increase noted in 16S diversity at the two-month sampling on acetate-alone, entirely related to an increase in Bacterial diversity. Upon return to SBWW conditions in phase 4, all diversity measures returned to near phase 1 levels.

  11. Microbial diversity differences within aerobic granular sludge and activated sludge flocs.

    PubMed

    Winkler, M-K H; Kleerebezem, R; de Bruin, L M M; Verheijen, P J T; Abbas, B; Habermacher, J; van Loosdrecht, M C M

    2013-08-01

    In this study, we investigated during 400 days the microbial community variations as observed from 16S DNA gene DGGE banding patterns from an aerobic granular sludge pilot plant as well as the from a full-scale activated sludge treatment plant in Epe, the Netherlands. Both plants obtained the same wastewater and had the same relative hydraulic variations and run stable over time. For the total bacterial population, a similarity analysis was conducted showing that the community composition of both sludge types was very dissimilar. Despite this difference, general bacterial population of both systems had on average comparable species richness, entropy, and evenness, suggesting that different bacteria were sharing the same functionality. Moreover, multi-dimensional scaling analysis revealed that the microbial populations of the flocculent sludge system moved closely around the initial population, whereas the bacterial population in the aerobic granular sludge moved away from its initial population representing a permanent change. In addition, the ammonium-oxidizing community of both sludge systems was studied in detail showing more unevenness than the general bacterial community. Nitrosomonas was the dominant AOB in flocculent sludge, whereas in granular sludge, Nitrosomonas and Nitrosospira were present in equal amounts. A correlation analysis of process data and microbial data from DGGE gels showed that the microbial diversity shift in ammonium-oxidizing bacteria clearly correlated with fluctuations in temperature. PMID:23064482

  12. Application of forward osmosis (FO) under ultrasonication on sludge thickening of waste activated sludge.

    PubMed

    Nguyen, Nguyen Cong; Nguyen, Hau Thi; Chen, Shiao-Shing; Nguyen, Nhat Thien; Li, Chi-Wang

    2015-01-01

    Forward osmosis (FO) is an emerging process for dewatering solid-liquid stream which has the potential to be innovative and sustainable. However, the applications have still been hindered by low water flux and membrane fouling when activated sludge is used as the feed solution due to bound water from microbial cells. Hence, a novel strategy was designed to increase sludge thickening and reduce membrane fouling in the FO process under ultrasonic condition. The results from the ultrasound/FO hybrid system showed that the sludge concentration reached up to 20,400 and 28,400 mg/L from initial sludge concentrations of 3000 and 8000 mg/L with frequency of 40 kHz after 22 hours, while the system without ultrasound had to spend 26 hours to achieve the same sludge concentration. This identifies that the presence of ultrasound strongly affected sludge structure as well as sludge thickening of the FO process. Furthermore, the ultrasound/FO hybrid system could achieve NH4+-N removal efficiency of 96%, PO4(3-)-P of 98% and dissolved organic carbon (DOC) of 99%. The overall performance demonstrates that the proposed ultrasound/FO system using seawater as a draw solution is promising for sludge thickening application. PMID:26465299

  13. Adsorption of heavy metals on sonicated activated sludge.

    PubMed

    Commenges-Bernole, N; Marguerie, J

    2009-01-01

    The objective of this work is to assess heavy metals fixation capacity on sonicated activated sludge. Ultrasonic treatment of sludge has lead to its desintegration and changes physico-chemical characteristics such as soluble chemical oxygen demand, proteins or particle size distribution. This study has shown that these modifications have improved significantly the capacity of sludge to fix heavy metals. Indeed, after a sonication of 15 min and storage of three days after irradiation, the equilibrium capacity is increased about 45%. The restructuration of sludge during the storage seems to increase the accessibility to active binding sites. PMID:18599337

  14. Microbiology of coke-plant activated sludge

    SciTech Connect

    Owens, J.R.

    1983-01-01

    The biological treatment of coke-plant wastewater represents the most economical means of detoxification and contaminant removal, but little is known about the microbial ecology of this system. Research was therefore undertaken to determine the kinds of microorganisms that survive and function in this environment and to examine the growth patterns that influence treatment efficiency. The microbial flora of coke-plant activated sludge is predominated by populations of aerobic gram negative rods. The principle genera identified were Pseudomonas, Alcaligenes, Flavobacterium and Acinetobacter. The genera Bacillus, Nocardia and Micrococcus were also present at low levels. A single type of rotifer was present along with various protozoans. The ability of microorganisms in coke wastewater to grow on various organic compounds as their sole source of carbon and energy is more restrictive when compared with that of isolates obtained from activated sludge processes treating municipal wastes. The phenol degrading bacteria can be maintained in a continuous culture system with a hydraulic retention time (HRT) of as long as 14 days. Under conditions of increasing HRT the average cell size decreased and the number of cells per milliter increased. As the HRT increased cell yields decreased. At long HRT's (7 to 14 days) cell yields remained constant.

  15. OXYGEN UTILIZATION IN ACTIVATED SLUDGE PLANTS: SIMULATION AND MODEL CALIBRATION

    EPA Science Inventory

    The objective of the research described in the report is to apply recent advances in activated sludge process modeling to the simulation of oxygen utilization rates in full scale activated sludge treatment plants. This is accomplished by calibrating the International Association ...

  16. PARALLEL EVALUATION OF AIR- AND OXYGEN-ACTIVATED SLUDGE

    EPA Science Inventory

    To provide data on the relative merits of air and oxygen in the activated sludge process, two 1900-cu m/day (0.5-mgd) activated sludge pilot plant, one air and one oxygen system, were operated side-by-side at the Joint Water Pollution Control Plant, Carson, California. Both of th...

  17. Effect of hydraulic retention time and sludge recirculation on greenhouse gas emission and related microbial communities in two-stage membrane bioreactor treating solid waste leachate.

    PubMed

    Nuansawan, Nararatchporn; Boonnorat, Jarungwit; Chiemchaisri, Wilai; Chiemchaisri, Chart

    2016-06-01

    Methane (CH4) and nitrous oxide (N2O) emissions and responsible microorganisms during the treatment of municipal solid waste leachate in two-stage membrane bioreactor (MBR) was investigated. The MBR system, consisting of anaerobic and aerobic stages, were operated at hydraulic retention time (HRT) of 5 and 2.5days in each reactor under the presence and absence of sludge recirculation. Organic and nitrogen removals were more than 80% under all operating conditions during which CH4 emission were found highest under no sludge recirculation condition at HRT of 5days. An increase in hydraulic loading resulted in a reduction in CH4 emission from anaerobic reactor but an increase from the aerobic reactor. N2O emission rates were found relatively constant from anaerobic and aerobic reactors under different operating conditions. Diversity of CH4 and N2O producing microorganisms were found decreasing when hydraulic loading rate to the reactors was increased. PMID:26860618

  18. Sludge.

    ERIC Educational Resources Information Center

    Tenenbaum, David

    1992-01-01

    Cites a recycling success story involving sludge production from wastewater and transformation into an effective plant fertilizer. Discusses related concerns such as dealing with pollutants like heavy metals and PCBs often found in sludge. Provides an example of an application of sludge produced in Chicago to an area reclamation site. (MCO)

  19. Advanced sludge treatment affects extracellular polymeric substances to improve activated sludge dewatering.

    PubMed

    Neyens, Elisabeth; Baeyens, Jan; Dewil, Raf; De heyder, Bart

    2004-01-30

    The management of wastewater sludge, now often referred to as biosolids, accounts for a major portion of the cost of the wastewater treatment process and represents significant technical challenges. In many wastewater treatment facilities, the bottleneck of the sludge handling system is the dewatering operation. Advanced sludge treatment (AST) processes have been developed in order to improve sludge dewatering and to facilitate handling and ultimate disposal. The authors have extensively reported lab-scale, semi-pilot and pilot investigations on either thermal and thermochemical processes, or chemical oxidation using hydrogen peroxide. To understand the action of these advanced sludge technologies, the essential role played by extracellular polymeric substances (EPS) needs to be understood. EPS form a highly hydrated biofilm matrix, in which the micro-organisms are embedded. Hence they are of considerable importance in the removal of pollutants from wastewater, in bioflocculation, in settling and in dewatering of activated sludge. The present paper reviews the characteristics of EPS and the influence of thermochemical and oxidation mechanisms on degradation and flocculation of EPS. Experimental investigations on waste activated sludge are conducted by the authors to evaluate the various literature findings. From the experiments, it is concluded that AST methods enhance cake dewaterability in two ways: (i) they degrade EPS proteins and polysaccharides reducing the EPS water retention properties; and (ii) they promote flocculation which reduces the amount of fine flocs. PMID:15177096

  20. Production of carboxylates from high rate activated sludge through fermentation.

    PubMed

    Cagnetta, C; Coma, M; Vlaeminck, S E; Rabaey, K

    2016-10-01

    The aim of this work was to study the key parameters affecting fermentation of high rate activated A-sludge to carboxylates, including pH, temperature, inoculum, sludge composition and iron content. The maximum volatile fatty acids production was 141mgCg(-1) VSSfed, at pH 7. Subsequently the potential for carboxylate and methane production for A-sludge from four different plants at pH 7 and 35°C were compared. Initial BOD of the sludge appeared to be key determining carboxylate yield from A-sludge. Whereas methanogenesis could be correlated linearly to the quantity of ferric used for coagulation, fermentation did not show a dependency on iron presence. This difference may enable a strategy whereby A-stage sludge is separated to achieve fermentation, and iron dosing for phosphate removal is only implemented at the B-stage. PMID:27020399

  1. Factors influencing sorption of ciprofloxacin onto activated sludge: experimental assessment and modelling implications.

    PubMed

    Polesel, Fabio; Lehnberg, Kai; Dott, Wolfgang; Trapp, Stefan; Thomas, Kevin V; Plósz, Benedek Gy

    2015-01-01

    Many of the pharmaceuticals and personal care products occurring in municipal sewage are ionizing substances, and their partitioning behaviour is affected by ionic interactions with solid matrices. In activated sludge systems, such interactions have currently not been adequately understood and described, particularly for zwitterionic chemicals. Here we present an assessment of the effects of pH and iron salt dosing on the sorption of ciprofloxacin onto activated sludge using laboratory experiments and full-scale fate modelling. Experimental results were described with Freundlich isotherms and showed that non-linear sorption occurred under all the conditions tested. The greatest sorption potential was measured at pH=7.4, at which ciprofloxacin is speciated mostly as zwitterion. Iron salt dosing increased sorption under aerobic and, to a lesser extent, anoxic conditions, whereas no effect was registered under anaerobic conditions. The activated sludge model for xenobiotics (ASM-X) was extended with Freundlich-based sorption kinetics and used to predict the fate of ciprofloxacin in a wastewater treatment plant (WWTP). Scenario simulations, using experimental Freundlich parameters, were used to identify whether the assessed factors caused a significant increase of aqueous ciprofloxacin concentration in full-scale bioreactors. Simulation results suggest that a pH increase, rather than a reduction in iron salt dosing, could be responsible for a systematic deterioration of sorption of ciprofloxacin in the WWTP. PMID:24972177

  2. The effect of different aeration conditions in activated sludge--Side-stream system on sludge production, sludge degradation rates, active biomass and extracellular polymeric substances.

    PubMed

    Habermacher, Jonathan; Benetti, Antonio Domingues; Derlon, Nicolas; Morgenroth, Eberhard

    2015-11-15

    On-site minimization of excess sludge production is a relevant strategy for the operation of small-scale and decentralized wastewater treatment plants. In the study, we evaluated the potential of activated sludge systems equipped with side-stream reactors (SSRs). This study especially focused on how the sequential exposure of sludge to different aeration conditions in the side-stream reactors influences the overall degradation of sludge and of its specific fractions (active biomass, extracellular polymeric substances (EPS), EPS proteins, EPS carbohydrates). We found that increasing the solid retention time from 25 to 40 and 80 days enhanced sludge degradation for all aeration conditions tested in the side-stream reactor. Also, the highest specific degradation rate and in turn the lowest sludge production were achieved when maintaining aerobic conditions in the side-stream reactors. The different sludge fractions in terms of active biomass (quantified based on adenosine tri-phosphate (ATP) measurements), EPS proteins and EPS carbohydrates were quantified before and after passage through the SSR. The relative amounts of active biomass and EPS to volatile suspended solids (VSS) did not changed when exposed to different aeration conditions in the SSRs, which indicates that long SRT and starvation in the SSRs did not promote the degradation of a specific sludge fraction. Overall, our study helps to better understand mechanisms of enhanced sludge degradation in systems operated at long SRTs. PMID:26295938

  3. Effect of sludge retention time on the biological performance of anaerobic membrane bioreactors treating corn-to-ethanol thin stillage with high lipid content.

    PubMed

    Dereli, Recep Kaan; van der Zee, Frank P; Heffernan, Barry; Grelot, Aurelie; van Lier, Jules B

    2014-02-01

    The potential of anaerobic membrane bioreactors (AnMBRs) for the treatment of lipid rich corn-to-ethanol thin stillage was investigated at three different sludge retention times (SRT), i.e. 20, 30 and 50 days. The membrane assisted biomass retention in AnMBRs provided an excellent solution to sludge washout problems reported for the treatment of lipid rich wastewaters by granular sludge bed reactors. The AnMBRs achieved high COD removal efficiencies up to 99% and excellent effluent quality. Although higher organic loading rates (OLRs) up to 8.0 kg COD m(-3) d(-1) could be applied to the reactors operated at shorter SRTs, better biological degradation efficiencies, i.e. up to 83%, was achieved at increased SRTs. Severe long chain fatty acid (LCFA) inhibition was observed at 50 days SRT, possibly caused by the extensive dissolution of LCFA in the reactor broth, inhibiting the methanogenic biomass. Physicochemical mechanisms such as precipitation with divalent cations and adsorption on the sludge played an important role in the occurrence of LCFA removal, conversion, and inhibition. PMID:24238260

  4. Ultrasonic waste activated sludge disintegration for improving anaerobic stabilization.

    PubMed

    Tiehm, A; Nickel, K; Zellhorn, M; Neis, U

    2001-06-01

    The pretreatment of waste activated sludge by ultrasonic disintegration was studied in order to improve the anaerobic sludge stabilization. The ultrasound frequency was varied within a range from 41 to 3217 kHz. The impact of different ultrasound intensities and treatment times was examined. Sludge disintegration was most significant at low frequencies. Low-frequency ultrasound creates large cavitation bubbles which upon collapse initiate powerful jet streams exerting strong shear forces in the liquid. The decreasing sludge disintegration efficiency observed at higher frequencies was attributed to smaller cavitation bubbles which do not allow the initiation of such strong shear forces. Short sonication times resulted in sludge floc deagglomeration without the destruction of bacteria cells. Longer sonication brought about the break-up of cell walls, the sludge solids were distintegrated and dissolved organic compounds were released. The anaerobic digestion of waste activated sludge following ultrasonic pretreatment causing microbial cell lysis was significantly improved. There was an increase in the volatile solids degradation as well as an increase in the biogas production. The increase in digestion efficiency was proportional to the degree of sludge disintegration. To a lesser degree the deagglomeration of sludge flocs also augmented the anaerobic volatile solids degradation. PMID:11337847

  5. Simultaneous activated carbon adsorption within a membrane bioreactor for an enhanced micropollutant removal.

    PubMed

    Li, Xueqing; Hai, Faisal I; Nghiem, Long D

    2011-05-01

    Significant adsorption of sulfamethoxazole and carbamazepine to powdered activated carbon (PAC) was confirmed by a series of adsorption tests. In contrast, adsorption of these micropollutants to the sludge was negligible. The removal of these compounds in membrane bioreactor (MBR) was dependent on their hydrophobicity and loading as well as the PAC dosage. Sulfamethoxazole exhibited better removal rate during operation under no or low (0.1g/L) PAC dosage. When the PAC concentration in MBR was raised to 1.0 g/L, a sustainable and significantly improved performance in the removal of both compounds was observed - the removal efficiencies of sulfamethoxazole and carbamazepine increased to 82 ± 11% and 92 ± 15% from the levels of 64 ± 7%, and negligible removal, respectively. The higher removal efficiency of carbamazepine at high (1.0 g/L) PAC dosage could be attributed to the fact that carbamazepine is relatively more hydrophobic than sulfamethoxazole, which subsequently resulted in its higher adsorption affinity toward PAC. PMID:21145232

  6. Performance enhancement with powdered activated carbon (PAC) addition in a membrane bioreactor (MBR) treating distillery effluent.

    PubMed

    Satyawali, Yamini; Balakrishnan, Malini

    2009-10-15

    This work investigated the effect of powdered activated carbon (PAC) addition on the operation of a membrane bioreactor (MBR) treating sugarcane molasses based distillery wastewater (spentwash). The 8L reactor was equipped with a submerged 30 microm nylon mesh filter with 0.05 m(2) filtration area. Detailed characterization of the commercial wood charcoal based PAC was performed before using it in the MBR. The MBR was operated over 200 days at organic loading rates (OLRs) varying from 4.2 to 6.9 kg m(-3)d(-1). PAC addition controlled the reactor foaming during start up and enhanced the critical flux by around 23%; it also prolonged the duration between filter cleaning. Operation at higher loading rates was possible and for a given OLR, the chemical oxygen demand (COD) removal was higher with PAC addition. However, biodegradation in the reactor was limited and the high molecular weight compounds were not affected by PAC supplementation. The functional groups on PAC appear to interact with the polysaccharide portion of the sludge, which may reduce its propensity to interact with the nylon mesh. PMID:19467782

  7. Ornithinimicrobium pekingense sp. nov., isolated from activated sludge.

    PubMed

    Liu, Xing-Yu; Wang, Bao-Jun; Jiang, Cheng-Ying; Liu, Shuang-Jiang

    2008-01-01

    The bacterial strain LW6(T) was isolated from activated sludge of a wastewater treatment bioreactor. Cells of strain LW6(T) are Gram-positive, irregular, short rods and cocci, 0.5-0.8x1.0-1.6 microm. Colonies are light-yellow, smooth, circular and 0.2-1.0 mm in diameter after 3 days incubation. Strain LW6(T) is aerobic and heterotrophic. It grows at a temperature range of 26-38 degrees C and pH range of 6-9, with optimal growth at 33-37 degrees C and pH 7.8-8.2. The predominant cellular fatty acids of strain LW6(T) are iso-C(15:0) (38.9%) and iso-C(17:1)omega9c (18.8%). Strain LW6(T) has the major respiratory menaquinones MK-8(H(4)) and MK-8(H(2)) and polar lipids phosphatidylinositol, phosphatidylglycerol, diphosphatidylglycerol and unknown glycolipid/phospholipids. The cell wall peptidoglycan of strain LW6(T) contained the amino acids ornithine, lysine, glutamic acid, alanine, glycine and aspartic acid. Its molar DNA G+C content is 69 mol% (T(m)). Analysis of 16S rRNA gene sequences indicated that strain LW6(T) was related phylogenetically to members of the genus Ornithinimicrobium, with similarities ranging from 98.3 to 98.7%. The DNA-DNA relatedness of strain LW6(T) to Ornithinimicrobium humiphilum DSM 12362(T) and Ornithinimicrobium kibberense K22-20(T) was respectively 31.5 and 15.2%. Based on these results, it is concluded that strain LW6(T) represents a novel species of the genus Ornithinimicrobium, for which the name Ornithinimicrobium pekingense sp. nov. is proposed. The type strain is strain LW6(T) (=CGMCC 1.5362(T) =JCM 14001(T)). PMID:18175694

  8. A STUDY OF NITRATE RESPIRATION IN THE ACTIVATED SLUDGE PROCESS

    EPA Science Inventory

    In an experimental, 570-cum/day (0.15-mgd) activated sludge plant treating domestic wastewater from a correctional facility, 76 to 87 percent nitrogen removal was obtained via sludge synthesis and biological denitrification using endogenous H-donors in a compartmentalized reactor...

  9. Enhancement of activated sludge disintegration and dewaterability by Fenton process

    NASA Astrophysics Data System (ADS)

    Heng, G. C.; Isa, M. H.

    2016-06-01

    Municipal and industrial wastewater treatment plants produce large amounts of sludge. This excess sludge is an inevitable drawback inherent to the activated sludge process. In this study, the waste activated sludge was obtained from the campus wastewater treatment plant at Universiti Teknologi PETRONAS (UTP), Malaysia. Fenton pretreatment was optimized by using the response surface methodology (RSM) to study the effects of three operating conditions including the dosage of H2O2 (g H2O2/kg TS), the molar ratio of H2O2/Fe2+ and reaction time. The optimum operating variables to achieve MLVSS removal 65%, CST reduction 28%, sCOD 11000 mg/L and EPS 500 mg/L were: 1000 g H2O2/kg TS, H2O2/Fe2+ molar ratio 70 and reaction time 45 min. Fenton process was proved to be able to enhance the sludge disintegration and dewaterability.

  10. Enhancement of sludge reduction and methane production by removing extracellular polymeric substances from waste activated sludge.

    PubMed

    Nguyen, Minh Tuan; Mohd Yasin, Nazlina Haiza; Miyazaki, Toshiki; Maeda, Toshinari

    2014-12-01

    The management of waste activated sludge (WAS) recycling is a concern that affects the development of the future low-carbon society, particularly sludge reduction and biomass utilization. In this study, we investigated the effect of removing extracellular polymeric substances (EPS), which play important roles in the adhesion and flocculation of WAS, on increased sludge disintegration, thereby enhancing sludge reduction and methane production by anaerobic digestion. EPS removal from WAS by ethylenediaminetetraacetic acid (EDTA) significantly enhanced sludge reduction, i.e., 49 ± 5% compared with 27 ± 1% of the control at the end the digestion process. Methane production was also improved in WAS without EPS by 8881 ± 109 CH4 μmol g(-1) dry-weight of sludge. Microbial activity was determined by denaturing gradient gel electrophoresis and real-time polymerase chain reaction, which showed that the hydrolysis and acetogenesis stages were enhanced by pretreatment with 2% EDTA, with a larger methanogenic community and better methane production. PMID:25277968

  11. Systematic investigation and microbial community profile of indole degradation processes in two aerobic activated sludge systems

    PubMed Central

    Ma, Qiao; Qu, Yuanyuan; Zhang, Xuwang; Liu, Ziyan; Li, Huijie; Zhang, Zhaojing; Wang, Jingwei; Shen, Wenli; Zhou, Jiti

    2015-01-01

    Indole is widely spread in various environmental matrices. Indole degradation by bacteria has been reported previously, whereas its degradation processes driven by aerobic microbial community were as-yet unexplored. Herein, eight sequencing batch bioreactors fed with municipal and coking activated sludges were constructed for aerobic treatment of indole. The whole operation processes contained three stages, i.e. stage I, glucose and indole as carbon sources; stage II, indole as carbon source; and stage III, indole as carbon and nitrogen source. Indole could be completely removed in both systems. Illumina sequencing revealed that alpha diversity was reduced after indole treatment and microbial communities were significantly distinct among the three stages. At genus level, Azorcus and Thauera were dominant species in stage I in both systems, while Alcaligenes, Comamonas and Pseudomonas were the core genera in stage II and III in municipal sludge system, Alcaligenes and Burkholderia in coking sludge system. In addition, four strains belonged to genera Comamonas, Burkholderia and Xenophilus were isolated using indole as sole carbon source. Burkholderia sp. IDO3 could remove 100 mg/L indole completely within 14 h, the highest degradation rate to date. These findings provide novel information and enrich our understanding of indole aerobic degradation processes. PMID:26657581

  12. Insights into the amplification of bacterial resistance to erythromycin in activated sludge.

    PubMed

    Guo, Mei-Ting; Yuan, Qing-Bin; Yang, Jian

    2015-10-01

    Wastewater treatment plants are significant reservoirs for antimicrobial resistance. However, little is known about wastewater treatment effects on the variation of antibiotic resistance. The shifts of bacterial resistance to erythromycin, a macrolide widely used in human medicine, on a lab-scale activated sludge system fed with real wastewater was investigated from levels of bacteria, community and genes, in this study. The resistance variation of total heterotrophic bacteria was studied during the biological treatment process, based on culture dependent method. The alterations of bacterial community resistant to erythromycin and nine typical erythromycin resistance genes were explored with molecular approaches, including high-throughput sequencing and quantitative polymerase chain reaction. The results revealed that the total heterotrophs tolerance level to erythromycin concentrations (higher than 32 mg/L) was significantly amplified during the activated sludge treatment, with the prevalence increased from 9.6% to 21.8%. High-throughput sequencing results demonstrated an obvious increase of the total heterotrophic bacterial diversity resistant to erythromycin. Proteobacteria and Bacteroidetes were the two dominant phyla in the influent and effluent of the bioreactor. However, the prevalence of Proteobacteria decreased from 76% to 59% while the total phyla number increased greatly from 18 to 29 through activated sludge treatment. The gene proportions of erm(A), mef(E) and erm(D) were greatly amplified after biological treatment. It is proposed that the transfer of antibiotic resistance genes through the variable mixtures of bacteria in the activated sludge might be the reason for the antibiotic resistance amplification. The amplified risk of antibiotic resistance in wastewater treatment needs to be paid more attention. PMID:25957255

  13. Active heterotrophic biomass and sludge retention time (SRT) as determining factors for biodegradation kinetics of pharmaceuticals in activated sludge.

    PubMed

    Majewsky, Marius; Gallé, Tom; Yargeau, Viviane; Fischer, Klaus

    2011-08-01

    The present study investigates the biodegradation of pharmaceutically active compounds (PhACs) by active biomass in activated sludge. Active heterotrophs (X(bh)) which are known to govern COD removal are suggested as a determining factor for biological PhAC removal as well. Biodegradation kinetics of five polar PhACs were determined in activated sludge of two wastewater treatment plants which differed in size, layout and sludge retention time (SRT). Results showed that active fractions of the total suspended solids (TSS) differed significantly between the two sludges, indicating that TSS does not reveal information about heterotrophic activity. Furthermore, PhAC removal was significantly faster in the presence of high numbers of heterotrophs and a low SRT. Pseudo first-order kinetics were modified to include X(bh) and used to describe decreasing PhAC elimination with increasing SRT. PMID:21652206

  14. Activated sludge process performance using a multistage tower aeration tank

    SciTech Connect

    Shimizu, Tatsuo; Kudo, Kenzo; Nasu, Yoshikazu )

    1993-07-01

    This study's objective was to clarify both experimentally and theoretically whether a vertical multistage tower aeration tank system is advantageous as compared with a completely mixed system, particularly with respect to purification efficiency, sludge settleability, and excess sludge production. In comparing the two systems: (1) purification efficiency in the multistage tower aeration system with partial fluid mixing with a large Peclet number was higher than in a corresponding completely mixed system for all applied organic loadings; (2) the multistage tower aeration system had some definite advantages with respect to sludge settleability and excess sludge production; and (3) the activated sludge system's higher performance with partial fluid mixing was shown quantitatively with the axial dispersion model in conjunction with growth kinetics which involved rapid uptake such as biosorption and subsequent oxidative biodegradation processes of organic substances.

  15. Assessment of denitrifying bacterial composition in activated sludge.

    PubMed

    Srinandan, C S; Shah, Mrinal; Patel, Bhavita; Nerurkar, Anuradha S

    2011-10-01

    The abundance and structure of denitrifying bacterial community in different activated sludge samples were assessed, where the abundance of denitrifying functional genes showed nirS in the range of 10(4)-10(5), nosZ with 10(4)-10(6) and 16S rRNA gene in the range 10(9)-10(10) copy number per ml of sludge. The culturable approach revealed Pseudomonas sp. and Alcaligenes sp. to be numerically high, whereas culture independent method showed betaproteobacteria to dominate the sludge samples. Comamonas sp. and Pseudomonas fluorescens isolates showed efficient denitrification, while Pseudomonas mendocina, Pseudomonas stutzeri and Brevundimonas diminuta accumulated nitrite during denitrification. Numerically dominant RFLP OTUs of the nosZ gene from the fertilizer factory sludge samples clustered with the known isolates of betaproteobacteria. The data also suggests the presence of different truncated denitrifiers with high numbers in sludge habitat. PMID:21868215

  16. Retrofitting activated sludge systems to intermittent aeration for nitrogen removal.

    PubMed

    Hanhan, O; Artan, N; Orhon, D

    2002-01-01

    The paper provides the basis and the conceptual approach of applying process kinetics and modelling to the design of alternating activated sludge systems for retrofitting existing activated sludge plants to intermittent aeration for nitrogen removal. It shows the significant role of the two specific parameters, namely, the aerated fraction and the cycle time ratio on process performance through model simulations and proposes a way to incorporate them into a design procedure using process stoichiometry and mass balance. It illustrates the effect of these parameters, together with the sludge age, in establishing the balance between the denitrification potential and the available nitrogen created in the anoxic/aerobic sequences of system operation. PMID:12420968

  17. Valuation of OSA process and folic acid addition as excess sludge minimization alternatives applied in the activated sludge process.

    PubMed

    Martins, C L; Velho, V F; Ramos, S R A; Pires, A S C D; Duarte, E C N F A; Costa, R H R

    2016-01-01

    The aim of this study was to investigate the ability of the oxic-settling-anaerobic (OSA)-process and the folic acid addition applied in the activated sludge process to reduce the excess sludge production. The study was monitored during two distinct periods: activated sludge system with OSA-process, and activated sludge system with folic acid addition. The observed sludge yields (Yobs) were 0.30 and 0.08 kgTSS kg(-1) chemical oxygen demand (COD), control phase and OSA-process (period 1); 0.33 and 0.18 kgTSS kg(-1) COD, control phase and folic acid addition (period 2). The Yobs decreased by 73 and 45% in phases with the OSA-process and folic acid addition, respectively, compared with the control phases. The sludge minimization alternatives result in a decrease in excess sludge production, without negatively affecting the performance of the effluent treatment. PMID:26901714

  18. SLUDGE COMBUSTOR USING SWIRL AND ACTIVE COMBUSTION CONTROL

    EPA Science Inventory

    A research program directed at developing technology for compact shipboard incinerators for sludges is described. The concept utilizes previously developed Vortex Containment Combustor (VCC) as a primary unit with an active combustion control afterburner (AB). The overall power s...

  19. DESIGN HANDBOOK FOR AUTOMATION OF ACTIVATED SLUDGE WASTEWATER TREATMENT PLANTS

    EPA Science Inventory

    This report is a systems engineering handbook for the automation of activated sludge wastewater treatment processes. Process control theory and application are discussed to acquaint the reader with terminology and fundamentals. Successful unit process control strategies currently...

  20. DESIGN PROCEDURES FOR DISSOLVED OXYGEN CONTROL OF ACTIVATED SLUDGE PROCESSES

    EPA Science Inventory

    This report presents design procedures and guidelines for the selection of aeration equipment and dissolved (DO) control systems for activated sludge treatment plants. Aeration methods, equipment and application techniques are examined and selection procedures offered. Various DO...

  1. ENHANCED BIODEGRADATION OF IOPROMIDE AND TRIMETHOPRIM IN NITRIFYING ACTIVATED SLUDGE

    EPA Science Inventory

    Iopromide and trimethoprim are frequently detected pharmaceuticals in effluents of wastewater treatment plants and in surface waters due to their persistence and high usage. Laboratory scale experiments showed that a significantly higher removal rate in nutrifying activated sludg...

  2. Optimization of the activated sludge anoxic reactor configuration as a means to control nutrient removal kinetically.

    PubMed

    Plósz, Benedek Gy

    2007-04-01

    Factors influencing the determination of optimum reactor configuration for activated sludge denitrification are investigated in this paper. A kinetic optimization method is presented to evaluate optimal pre- and post-denitrification bioreactor stages. Applying the method developed, simulation studies were carried out to investigate the impacts of the ratio of the influent readily biodegradable and slowly biodegradable substrates and the oxygen entering the denitrification zones on the optimal anoxic reactor configuration. In addition, the paper describes the effects of the slowly biodegradable substrate on the denitrification efficiency using external substrate dosing, and it demonstrates kinetic considerations concerning the hydrolysis process. It has been shown that as a function of the biodegradable substrate composition, the stage system design with three optimized reactor compartments can effectively increase reaction rates in the denitrification zones, and can provide flexibility for varying operation conditions. PMID:17321565

  3. Integrated fungal biomass and activated sludge treatment for textile wastewaters bioremediation.

    PubMed

    Anastasi, Antonella; Spina, Federica; Romagnolo, Alice; Tigini, Valeria; Prigione, Valeria; Varese, Giovanna Cristina

    2012-11-01

    A combined biological process was investigated for effective textile wastewater treatment. The process consisted of a first step performed by selected fungal biomasses, mainly devoted to the effluent decolourisation, and of a subsequent stage by means of activated sludge, in order to reduce the remaining COD and toxicity. In particular, the treatment with Trametes pubescens MUT 2400, selected over nine strains, achieved very good results in respect to all parameters. The final scale-up phase in a moving bed bioreactor with the supported biomass of the fungus allowed to verify the effectiveness of the treatment with high volumes. Despite promising results, further steps must be taken in order to optimize the use of these biomasses for a full exploitation of their oxidative potential in textile wastewater treatment. PMID:22940306

  4. Isolation of aluminum-tolerant bacteria capable of nitrogen removal in activated sludge.

    PubMed

    Ji, Bin; Chen, Wei; Zhu, Lei; Yang, Kai

    2016-05-15

    Four strains of bacteria capable of withstanding 20mM concentration of aluminum were isolated from activated sludge in a bioreactor. 16S rRNA identification and morphological characteristics indicated that these strains were Chryseobacterium sp. B1, Brevundimonas diminuta B3, Hydrogenophaga sp. B4, and Bacillus cereus B5. Phylogenetic analysis revealed the position and interrelationships of these bacteria. B. diminuta B3 and Hydrogenophaga sp. B4 could achieve nitrate nitrogen removal of 94.0% and 76.8% within 36h of its initial concentration of 148.8 and 151.7mg/L, respectively. Meanwhile, B3 and B4 could degrade ammonia with little nitrite accumulation. Results of this study provide more information about aluminum-resistant bacteria and laid the foundation for aluminum salt when it is simultaneously used for chemical precipitation. PMID:27038879

  5. The digestibility of waste activated sludges.

    PubMed

    Park, Chul; Abu-Orf, Mohammad M; Novak, John T

    2006-01-01

    Laboratory digestion studies using waste activated sludges (WAS) were conducted to compare the digestion performance between anaerobic and aerobic processes. Nine samples of WAS from seven wastewater treatment plants were collected and batch-digested under both anaerobic and aerobic conditions for 30 days at 25 degrees C. The cation content of wastewater (both floc and solution phases) and solution biopolymer (protein and polysaccharide) was measured before and after digestion and compared with volatile solids destruction data. The study revealed that each digestion process was associated with a distinct biopolymer fraction, which accounted for differences in volatile solids reduction under anaerobic and aerobic conditions. The anaerobic digestion data showed strong correlations between soluble protein generation, ammonium production, percent volatile solids reduction, and floc iron (Fe). These data suggest that the amount of volatile solids destroyed by anaerobic digestion depends on the Fe content of floc. In aerobic digestion, polysaccharide accumulated in solution along with calcium and magnesium. For aerobic digestion, correlations between divalent cation release and the production of inorganic nitrogen were found. This implies that divalent cation-bound biopolymer, thought to be lectin-like protein, was the primary organic fraction degraded under aerobic conditions. The results of the study show that the cation content in wastewater is an important indicator of the material that will digest under anaerobic or aerobic conditions and that some of the volatile solids will digest only under either anaerobic or aerobic conditions. PMID:16553167

  6. Effects of metabolic uncouplers on excess sludge reduction and microbial products of activated sludge.

    PubMed

    Fang, Fang; Hu, Hai-Lan; Qin, Min-Min; Xue, Zhao-Xia; Cao, Jia-Shun; Hu, Zhi-Rong

    2015-06-01

    The present study investigated the influences of three metabolic uncouplers (pCP, oCP and oNP) on excess activated sludge reduction and microbial products of extracellular polymeric substances (EPS) and intracellular storage product (polyhydroxybutyrate, PHB) in short-term tests. Results showed sludge was reduced 58.2%, 59.8% and 80.8%, respectively, at pCP, oCP and oNP concentrations of 20mg/L. The dosage of three uncouplers had no obviously influences on COD removal and sludge settleability, but had significant inhibition effect on ammonia removal, especially for oNP. Low concentration of pCP and oNP (5mg/L) dosing resulted in protein and polysaccharide content increased in EPS, however, they were decreased at high pCP and oNP concentrations (>5mg/L). To oCP, the protein content in EPS was increased linearly with oCP concentration. Furthermore, metabolic uncouplers addition stimulated the production of PHB. Among three uncouplers, oCP could be an alternative uncoupler for sludge reduction in activated sludge process. PMID:25746471

  7. Effect of a microbiota activator on accumulated ammonium and microbial community structure in a pilot-scale membrane bioreactor.

    PubMed

    Sato, Yuya; Hori, Tomoyuki; Navarro, Ronald R; Ronald, Navarro R; Habe, Hiroshi; Ogata, Atsushi

    2015-01-01

    Microbiota activators (MAs) have been used to improve the reactor performances of biological wastewater treatment processes. In this study, to remove ammonium (NH4(+)) accumulated during the pre-operation of a pilot-scale membrane bioreactor (MBR) under high-organic-loading conditions, an MA was added to the MBR system and the resulting changes in reactor performances and microbial communities were monitored for 12 days. The NH4(+) concentrations in the sludge and effluent decreased (from 427 to 246 mg/L in the sludge (days 1-9)), and mixed liquor suspended solid increased (from 6,793 to 11,283 mg/L (days 1-12)) after the addition of MA. High-throughput Illumina sequencing of 16S rRNA genes revealed that the microbial community structure changed along with the NH4(+) removal resulting from the MA addition. In particular, the relative abundance of an Acidovorax-related operational taxonomic unit (OTU) increased significantly, accounting for approximately 50% of the total microbial population at day 11. In contrast, the ammonia-oxidizing bacteria and archaea showed low abundances (<0.05%), and no anaerobic ammonia oxidizers were detected. These results suggested that the Acidovorax-related OTU was mainly involved in the NH4(+) removal in the MBR, probably due to its ammonia-assimilating metabolism. PMID:26377133

  8. [Biodiversity and Function Analyses of BIOLAK Activated Sludge Metagenome].

    PubMed

    Tian, Mei; Liu, Han-hu; Shen, Xin; Zhao, Fang-qing; Chen, Shuai; Yao, Yong-jia

    2015-05-01

    The BIOLAK is a multi-stage activated sludge process, which has been successfully promoted worldwide. However, the biological community and function of the BIOLAK activated sludge ( the core component in the process) have not been reported so far. In this study, taking Lianyungang Dapu Industrial Zone WWTP as an example, a large-scale metagenomic data (428 588 high-quality DNA sequences) of the BIOLAK activated sludge were obtained by means of a new generation of high-throughput sequencing technology. Amazing biodiversity was revealed in the BIOLAK activated sludge, which included 47 phyla, 872 genera and 1351 species. There were 33 phyla identified in the Bacteria domain (289 933 sequences). Proteohacteria was the most abundant phylum (62.54%), followed by Bacteroidetes (11.29%), Nitrospirae ( 5. 65%) and Planctomycetes (4.79%), suggesting that these groups played a key role in the BIOLAK wastewater treatment system. Among the 748 bacterial genera, Nitrospira (5.60%) was the most prevalent genus, which was a key group in the nitrogen cycle. Followed by Gemmatimonas (2.45%), which was an important genus in the biological phosphorus removal process. In Archaea domain (1019 sequences), three phyla and 39 genera were detected. In Eukaryota domain (1055 sequences), 60 genera and 10 phyla were identified, among which Ciliophora was the largest phylum (257 sequences). Meanwhile, 448 viral sequences were detected in the BIOLAK sludge metagenome, which were dominated by bacteriophages. The proportions of nitrogen, aromatic compounds and phosphorus metabolism in the BIOLAK sludge were 2.50%, 2.28% and 1.56%, respectively, which were higher than those in the sludge of United States and Australia. Among four processes of nitrogen metabolism, denitrification-related genes were most abundant (80.81%), followed by ammonification (12.78%), nitrification,(4.38%) and nitrogen fixation (2.04%). In conclusion, the BIOLAK activated sludge had amazing biodiversity, meanwhile

  9. Sorption and degradation of bisphenol A by aerobic activated sludge.

    PubMed

    Zhao, Junming; Li, Yongmei; Zhang, Chaojie; Zeng, Qingling; Zhou, Qi

    2008-06-30

    Laboratory-scale batch experiments were conducted to investigate the sorption and degradation of bisphenol A (BPA) at microg/L range in an aerobic activated sludge system. The sorption isotherms and thermodynamics indicated that the sorption of BPA on sludge was mainly a physical process in which partitioning played a dominating role. The values of sorption coefficient Koc were between 621 and 736 L/kg in the temperature range of 10-30 degrees C. Both mixed liquor suspended solid (MLSS) and temperature influenced BPA sorption on sludge. The degradation of BPA by acclimated activated sludge could be described by first-order reaction equation with the first-order degradation rate constant of 0.80 h(-1) at 20 degrees C. The decrease of initial COD concentration and the increase of MLSS concentration and temperature enhanced BPA degradation rate. The removal of BPA in the activated sludge system was characterized by a quick sorption on the activated sludge and subsequent biodegradation. PMID:18179868

  10. Distribution and microbial community structure analysis of a single-stage partial nitritation/anammox granular sludge bioreactor operating at low temperature.

    PubMed

    Rodriguez-Sanchez, Alejandro; Purswani, Jessica; Lotti, Tommaso; Maza-Marquez, Paula; van Loosdrecht, M C M; Vahala, Riku; Gonzalez-Martinez, Alejandro

    2016-09-01

    In the last decade, autotrophic nitrogen removal technologies based on anammox metabolism have become state of the art in urban and industrial wastewater treatment systems, due to their advantages over traditional nitrogen removal processes. However, their application is currently limited to the treatment of warm wastewater (25-40°C) mainly due to the low growth rate of the anammox bacteria. The extension of the application field to wastewater characterized by lower temperatures (8-20°C), such as those typical for municipal sewage, allows the design of treatment systems with a net energy production. In this study, the distribution and bacterial community structure of a lab-scale single-stage partial nitritation/anammox (PN/A) granular sludge bioreactor operating at low temperatures was analysed using next-generation sequencing techniques. The presence of ammonium-oxidizing bacteria and anammox bacteria was found, but the appearance of other bacterial species shows a complex microbial ecosystem. Evaluation of ecological roles of representative species inside the single-stage PN/A bioreactor was accomplished. Results obtained will be helpful for the future design and operation of PN/A systems performing at low temperatures. PMID:26829222

  11. Comparative study of MBR and activated sludge in the treatment of paper mill wastewater.

    PubMed

    Lerner, M; Stahl, N; Galil, N I

    2007-01-01

    The study was based on a full scale activated sludge plant (AS) compared to a parallel operated pilot membrane bioreactor (MBR) with flat sheets membranes. Both systems received their influent from an anaerobic bioreactor treating paper mill wastewater. MBR produced an effluent of much better quality than AS in terms of suspended solids, containing 1 mg/L or less in 80% of the monitoring time, while the AS effluent contained 12 mg/L. This could save the necessity of further treatment by filtration in the case of MBR. Other effluent quality parameters, such as organic matter (COD and BOD), phosphorus and ammonia nitrogen, did not indicate substantial differences between AS and MBR. Calcium carbonate scaling and formation of a bacterial layer on the membrane caused severe flux reduction. The membrane blockage because of scaling and biofouling proved to be very serious, therefore, it required proper and more complicated maintenance than the AS system. This study leads to the conclusion that in the case of paper mill wastewater, after anaerobic biotreatment, if there is no need for excellent effluent quality in terms of suspended solids, the replacement of the AS by the MBR would not be strongly justified, mainly because of maintenance cost. PMID:17486831

  12. Cometabolic degradation of organic wastewater micropollutants by activated sludge and sludge-inherent microorganisms.

    PubMed

    Fischer, Klaus; Majewsky, Marius

    2014-08-01

    Municipal wastewaters contain a multitude of organic trace pollutants. Often, their biodegradability by activated sludge microorganisms is decisive for their elimination during wastewater treatment. Since the amounts of micropollutants seem too low to serve as growth substrate, cometabolism is supposed to be the dominating biodegradation process. Nevertheless, as many biodegradation studies were performed without the intention to discriminate between metabolic and cometabolic processes, the specific contribution of the latter to substance transformations is often not clarified. This minireview summarizes current knowledge about the cometabolic degradation of organic trace pollutants by activated sludge and sludge-inherent microorganisms. Due to their relevance for communal wastewater contamination, the focus is laid on pharmaceuticals, personal care products, antibiotics, estrogens, and nonylphenols. Wherever possible, reference is made to the molecular process level, i.e., cometabolic pathways, involved enzymes, and formed transformation products. Particular cometabolic capabilities of different activated sludge consortia and various microbial species are highlighted. Process conditions favoring cometabolic activities are emphasized. Finally, knowledge gaps are identified, and research perspectives are outlined. PMID:24866947

  13. [Performance of internal-loop air-lift nitrifying bioreactor].

    PubMed

    Lin, Feng-Mei; Zheng, Ping; Zhao, Yang-Yang; Hu, Bao-Lan; Chen, Jian-Song

    2002-07-01

    The performance of internal-loop air-lift nitrifying bioreactor was good with strong tolerance to influent ammonia concentration (78.49 mmol/L), high volume converting rate (163.18 mmol/L.d) and obvious working stability (ammonia removal > 94.42%). During operation of internal-loop air-lift bioreactor, the nitrifying activated sludge was granulated. The nitrifying granular activated sludge began to appear on day 45. Its average diameter was 0.83 mm, settling velocity was 55.53 m/h and specific ammonia removal rate was 0.95 mmol (NH4(+)-N)/g (VS).d. The nitrifying granular activated sludge had the activity for anaerobic ammonia oxidation with ammonia oxidation rate of 0.23 mmol (NH4(+)-N)/g(VS).d and nitrite reduction rate of 0.24 mmol (NO2(-)-N)/g(VS).d. PMID:12385250

  14. The stability of aerobic granular sludge under 4-chloroaniline shock in a sequential air-lift bioreactor (SABR).

    PubMed

    Zhu, Liang; Lv, Mei-le; Dai, Xin; Zhou, Jia-heng; Xu, Xiang-yang

    2013-07-01

    The aerobic granular sludge technology has a great potential in treatment of municipal wastewater and industrial wastewater containing toxic non-degradable pollutants. However, the formation and structural stability of aerobic granular sludge is susceptible to toxic shock. In the study, the effect of 4-chloroaniline (4-ClA) as a common toxic pollutant on the granular structure and performance was investigated, and the mechanism was revealed to provide more information on 4-ClA degradation with aerobic granular sludge process. The results showed that a 4-ClA shock at influent 200 mg L(-1) could cause the disintegration of aerobic granular sludge and decrease of the pollutant removal performance. The analysis of extracellular polymeric substances (EPS) within the mature and disintegrated granular sludge showed that the decrease of protein content in EPS, especially the components like Amide I 3-turn helix and β-sheet structures and aspartate, was not good for the stability of aerobic granular sludge. The microbial community results demonstrated that the disappearance of dominant bacteria like Kineosphaera limosa or appearance like Acinetobacter, might contribute to the reduction of EPS and disintegration of aerobic granular sludge. PMID:23685649

  15. Steady-state analysis of activated sludge processes with a settler model including sludge compression.

    PubMed

    Diehl, S; Zambrano, J; Carlsson, B

    2016-01-01

    A reduced model of a completely stirred-tank bioreactor coupled to a settling tank with recycle is analyzed in its steady states. In the reactor, the concentrations of one dominant particulate biomass and one soluble substrate component are modelled. While the biomass decay rate is assumed to be constant, growth kinetics can depend on both substrate and biomass concentrations, and optionally model substrate inhibition. Compressive and hindered settling phenomena are included using the Bürger-Diehl settler model, which consists of a partial differential equation. Steady-state solutions of this partial differential equation are obtained from an ordinary differential equation, making steady-state analysis of the entire plant difficult. A key result showing that the ordinary differential equation can be replaced with an approximate algebraic equation simplifies model analysis. This algebraic equation takes the location of the sludge-blanket during normal operation into account, allowing for the limiting flux capacity caused by compressive settling to easily be included in the steady-state mass balance equations for the entire plant system. This novel approach grants the possibility of more realistic solutions than other previously published reduced models, comprised of yet simpler settler assumptions. The steady-state concentrations, solids residence time, and the wastage flow ratio are functions of the recycle ratio. Solutions are shown for various growth kinetics; with different values of biomass decay rate, influent volumetric flow, and substrate concentration. PMID:26476681

  16. Contribution of extracellular polymeric substances (EPS) and their subfractions to the sludge aggregation in membrane bioreactor coupled with worm reactor.

    PubMed

    Li, Zhipeng; Tian, Yu; Ding, Yi; Wang, Haoyu; Chen, Lin

    2013-09-01

    This study focused on the effect of predated sludge recycle on the contribution of extracellular polymeric substances (EPSs) and their subfractions to sludge aggregation in combined MBR system. It was observed that aggregation abilities of sludge samples were decreased by worm predation. Furthermore, worm predation enhanced the energy barriers and weakened the secondary energy minimum in the interaction energy profiles of slime, loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS). Further investigations demonstrated that the content decrease and structural change of different EPS fractions induced by worm predation may be the reason for the decreased aggregation of sludge. Concomitantly, the adsorption tests and atomic force microscopy observation confirmed that the worm predation decreased the adsorption of slime, LB-EPS and TB-EPS on membrane. This would indicate the worm predation could keep an optimum EPS level for which floc structure was maintained and the fouling propensity of mixed liquid was reduced. PMID:23891833

  17. Polyhydroxyalkanoate production potential of heterotrophic bacteria in activated sludge.

    PubMed

    Inoue, Daisuke; Suzuki, Yuta; Uchida, Takahiro; Morohoshi, Jota; Sei, Kazunari

    2016-01-01

    This study was conducted to evaluate the polyhydroxyalkanoate (PHA) production potential of cultivable heterotrophic bacteria in activated sludge by genotypic and phenotypic characterizations. A total of 114 bacterial strains were isolated from four activated sludge samples taken from a lab-scale sequencing batch reactor and three wastewater treatment processes of two municipal wastewater treatment plants. PCR detection of the phaC genes encoding class I and II PHA synthase revealed that 15% of the total isolates possessed phaC genes, all of which had the closest similarities to known phaC genes of α- and β-Proteobacteria and Actinobacteria. PHA production experiments under aerobic and nitrogen-limited conditions showed that 68% of the total isolates were capable of producing PHA from at least one of the six substrates used (acetate, propionate, lactate, butyrate, glucose and glycerol). Genotypic and phenotypic characterizations revealed that 75% of the activated sludge bacteria had PHA production potential. Our results also indicated that short-chain fatty acids would be the preferable substrates for PHA production by activated sludge bacteria, and that there might be a variety of unidentified phaC genes in activated sludge. PMID:26071670

  18. EFFECT OF VAPOR-PHASE BIOREACTOR OPERATION ON BIOMASS ACCUMULATION, DISTRIBUTION, AND ACTIVITY. (R826168)

    EPA Science Inventory

    Excess biomass accumulation and activity loss in vapor-phase bioreactors (VPBs) can lead to unreliable long-term operation. In this study, temporal and spatial variations in biomass accumulation, distribution and activity in VPBs treating toluene-contaminated air were monitored o...

  19. Anaerobic bioleaching of metals from waste activated sludge.

    PubMed

    Meulepas, Roel J W; Gonzalez-Gil, Graciela; Teshager, Fitfety Melese; Witharana, Ayoma; Saikaly, Pascal E; Lens, Piet N L

    2015-05-01

    Heavy metal contamination of anaerobically digested waste activated sludge hampers its reuse as fertilizer or soil conditioner. Conventional methods to leach metals require aeration or the addition of leaching agents. This paper investigates whether metals can be leached from waste activated sludge during the first, acidifying stage of two-stage anaerobic digestion without the supply of leaching agents. These leaching experiments were done with waste activated sludge from the Hoek van Holland municipal wastewater treatment plant (The Netherlands), which contained 342 μg g(-1) of copper, 487 μg g(-1) of lead, 793 μg g(-1) of zinc, 27 μg g(-1) of nickel and 2.3 μg g(-1) of cadmium. During the anaerobic acidification of 3 gdry weight L(-1) waste activated sludge, 80-85% of the copper, 66-69% of the lead, 87% of the zinc, 94-99% of the nickel and 73-83% of the cadmium were leached. The first stage of two-stage anaerobic digestion can thus be optimized as an anaerobic bioleaching process and produce a treated sludge (i.e., digestate) that meets the land-use standards in The Netherlands for copper, zinc, nickel and cadmium, but not for lead. PMID:25659306

  20. Fate and toxicity of melamine in activated sludge treatment systems after a long-term sludge adaptation.

    PubMed

    Xu, Shengnan; Zhang, Yanyan; Sims, Atreyee; Bernards, Matthew; Hu, Zhiqiang

    2013-05-01

    Melamine is a nitrogen-rich (67% nitrogen by mass) heterocyclic aromatic compound that could significantly increase effluent total nitrogen concentrations. In this study, we investigated the degradation of melamine and its impact on activated sludge operations by employing two common activated sludge processes, namely the Modified Ludzack-Ettinger (MLE) process and the continuous stirred tank reactor (CSTR) process. Melamine was dosed continuously from day 125 in both activated sludge treatment systems at an influent concentration of 3 mg/L for about 100 days. Even after such a long period of sludge adaptation, melamine appeared not to be easily biodegradable. The average melamine removal efficiencies in the CSTR and MLE systems were 14 ± 10% and 20 ± 15%, respectively. There was no significant difference in melamine removal between the two different activated sludge processes. The long-term input of melamine resulted in a decrease in the nitrifying bacterial activities (by 82 ± 8%) and population in both systems. Short-term microtiter assay results also showed that melamine reduced activated sludge growth by 80% when supplied at a concentration of 75.6 mg/L. These results suggest that sludge adaptation plays a minimal role in melamine degradation, as the enzymes responsible for hydrolytic deamination of melamine in activated sludge are not easily induced. The insignificant biodegradation of melamine is also attributed to bacterial growth inhibition under long-term dosing conditions with melamine, resulting in a significant decrease in effluent water quality. PMID:23466035

  1. Ecotoxicity and Biodegradability Assessment of Metalworking Fluids by Activated Sludge Bacteria

    NASA Astrophysics Data System (ADS)

    Gerulová, Kristína; Mihálková, Adriána; Šergovičová, Magdaléna; Guoth, Alexander; Nádašská, Zuzana

    2011-01-01

    The main aim of this study was to evaluate toxicity of metalworking fluids to bacterial consortium of activated sludge according to OECD 209 (STN EN ISO 8192) and a potential of the same sludge to degrade a part of the fluids according to OECD 302B. Toxic impact can affect different responses, particularly the inhibition of respiration measured from the oxygen consumption in a closed bottle. The degradation rate was calculated from COD according to the authors such as van der Gast and Ian Thompson (1, 2) who tested the degradability of some MWFs in bioreactors by measuring the COD. The lowest toxic MWF's were Cimstar 597 and Emulzin H (the highest tested concentration was below EC50), then Zubora TXS (EC50 - 11 349 mg l-1), Aquamet LAK-E (EC50 - 5 228 mg l-1), Adrana D 407 (EC50 - 4 351 mg l-1) followed, and finally, Hocut 3380 (EC50 - 2 339 mg l-1) was assessed as the most toxic. Important in this test (OECD 302B) is that the starting concentration of the tested substance must not decrease below 20% after 3 hours of cultivating. After that, it is impossible to distinguish biological degradation of organic matter from abiotic elimination from the suspension through adsorption. Tested were 8 MWFs of similar concentration and different addition of activated sludge - 0.25 g l-1, 0.50 g l-1 and 1.00 g l-1. The test showed that, after the first 3 hours of cultivating, adsorption grew with the increasing amount of inoculums, except of Akvol B (the decrease of the starting concentration after the first 3 hours of cultivating was the lowest of all and below 20%). It can be stated that, according to the test basic conditions, all the tested MWFs have a potential to ultimate degradation.

  2. Nonoxidative removal of organics in the activated sludge process

    PubMed Central

    Modin, Oskar; Persson, Frank; Wilén, Britt-Marie; Hermansson, Malte

    2016-01-01

    ABSTRACT The activated sludge process is commonly used to treat wastewater by aerobic oxidation of organic pollutants into carbon dioxide and water. However, several nonoxidative mechanisms can also contribute to removal of organics. Sorption onto activated sludge can remove a large fraction of the colloidal and particulate wastewater organics. Intracellular storage of, e.g., polyhydroxyalkanoates (PHA), triacylglycerides (TAG), or wax esters can convert wastewater organics into precursors for high-value products. Recently, several environmental, economic, and technological drivers have stimulated research on nonoxidative removal of organics for wastewater treatment. In this paper, we review these nonoxidative removal mechanisms as well as the existing and emerging process configurations that make use of them for wastewater treatment. Better utilization of nonoxidative processes in activated sludge could reduce the wasteful aerobic oxidation of organic compounds and lead to more resource-efficient wastewater treatment plants. PMID:27453679

  3. Degradation of mono-fluorophenols by an acclimated activated sludge.

    PubMed

    Chaojie, Zhang; Qi, Zhou; Ling, Chen; Yuan, Yuan; Hui, Yu

    2007-02-01

    Acclimated activated sludge was examined for its ability to degrade mono-fluorophenols as the sole carbon source in aerobic batch cultures. The acclimated activated sludge degraded fluorophenol efficiently. It degraded 100 mg/l 3-fluoropheno and 4-fluorophenol in 16 h with, respectively, 99.85% and 99.91% fluoride anion release and it degraded 50 mg/l 2-fluorophenol in 15 h with 99.26% fluoride anion release. The aerobic biodegradability of the mono-fluorophenols decreased in the order: 4-fluorophenol > 3-fluorophenol > 2-fluorophenol, resulting mainly from a different octanol/water partition coefficient and different steric parameter of the fluorophenols. The mechanism study revealed that the initial step in the aerobic biodegradation of mono-fluorophenols by the activated sludge was their transformation to fluorocatechol. Following transformation of the fluorophenol to fluorocatechol, ring cleavage by catechol 1, 2-dioxygenases proceeded via an ortho-cleavage pathway, then defluorination occurred. PMID:16819592

  4. Biodegradability of wastewater and activated sludge organics in anaerobic digestion.

    PubMed

    Ikumi, D S; Harding, T H; Ekama, G A

    2014-06-01

    The investigation provides experimental evidence that the unbiodegradable particulate organics fractions of primary sludge and waste activated sludge calculated from activated sludge models remain essentially unbiodegradable in anaerobic digestion. This was tested by feeding the waste activated sludge (WAS) from three different laboratory activated sludge (AS) systems to three separate anaerobic digesters (AD). Two of the AS systems were Modified Ludzack - Ettinger (MLE) nitrification-denitrification (ND) systems and the third was a membrane University of Cape Town (UCT) ND and enhanced biological P removal system. One of the MLE systems and the UCT system were fed the same real settled wastewater. The other MLE system was fed raw wastewater which was made by adding a measured constant flux (gCOD/d) of macerated primary sludge (PS) to the real settled wastewater. This PS was also fed to a fourth AD and a blend of PS and WAS from settled wastewater MLE system was fed to a fifth AD. The five ADs were each operated at five different sludge ages (10-60d). From the measured performance results of the AS systems, the unbiodegradable particulate organic (UPO) COD fractions of the raw and settled wastewaters, the PS and the WAS from the three AS systems were calculated with AS models. These AS model based UPO fractions of the PS and WAS were compared with the UPO fractions calculated from the performance results of the ADs fed these sludges. For the PS, the UPO fraction calculated from the AS and AD models matched closely, i.e. 0.30 and 0.31. Provided the UPO of heterotrophic (OHO, fE_OHO) and phosphorus accumulating (PAO, fE_PAO) biomass were accepted to be those associated with the death regeneration model of organism "decay", the UPO of the WAS calculated from the AS and AD models also matched well - if the steady state AS model fE_OHO = 0.20 and fE_PAO = 0.25 values were used, then the UPO fraction of the WAS calculated from the AS models deviated significantly

  5. Activated sludge acclimatisation kinetics to non-ionic surfactants.

    PubMed

    Carvalho, G; Novais, J M; Pinheiro, H M

    2003-01-01

    The biodegradation of surfactants is a frequent and complex problem in domestic and industrial wastewater treatment processes. In addition to the resulting metabolites being sometimes refractory, the complete biodegradation of many of the most employed non-ionic surfactants requires long hydraulic retention times and the presence of specialised bacterial consortia. Preliminary acclimatisation tests highlighted the importance of the sludge acclimatisation state to a specific surfactant substrate for biotreatment efficiency. This paper reports on studies aimed at quantifying activated sludge acclimatisation and memory retention levels when subjected to changes in the type of surfactant included in the feed. Several transitions were tested, namely from an alkylphenol ethoxylate to a linear alkyl ethoxylate and the reverse, and between alkyl ethoxylates with different hydrophobic and hydrophilic molecular chain lengths. The kinetic results showed that sludge activation and memory loss were more dynamic for primary biodegradation It was found that the sludge was harder to adapt to alkylphenol ethoxylate than to alkyl ethoxylate. The former also apparently introduced an inhibitory effect, resulting in very slow degradation kinetics when imposed to alkyl ethoxylate acclimatised sludge. When replacing an alkyl ethoxylate with another surfactant of the same family, a longer ethoxylate chain reduced the degradation rates. This effect was further enhanced by simultaneously increasing the hydrophobic chain length of the substrate. The acclimatisation kinetic after the replacement of an alkyl ethoxylate by a longer counterpart was slower than the reverse case, and memory was also more easily lost. PMID:12641258

  6. Landfill leachate characterization for simulation of biological treatment with Activated Sludge Model No. 1 and Activated Sludge Model No. 3.

    PubMed

    Galleguillos, Marcelo; Vasel, Jean-Luc

    2011-01-01

    Landfill leachates can be characterized correctly in terms of Activated Sludge Model No. 1 (ASM1) and Activated Sludge Model No. 3 (ASM3) variables. The wastewater characterization of leachate from a Luxembourg landfill was based on a physical-chemical method combined with a BOD analysis for the COD fractions and on standard analysis for forms of nitrogen. The results show important differences compared with municipal wastewater. High amounts of organic matter with low biodegradability were found, as well as a high concentration of ammonium nitrogen. Based on average values, a generic ASM characterization is proposed for landfill leachates. It can be directly employed in the early stages of the simulation of landfill leachate treatment with activated sludge models. PMID:21970168

  7. Anaerobic granular sludge as a biocatalyst for 1,3-propanediol production from glycerol in continuous bioreactors.

    PubMed

    Gallardo, R; Faria, C; Rodrigues, L R; Pereira, M A; Alves, M M

    2014-03-01

    1,3-Propanediol (1,3-PDO) was produced from glycerol in three parallel Expanded Granular Sludge Blanket (EGSB) reactors inoculated with granular sludge (control reactor-R1), heat-treated granular sludge (R2) and disrupted granular sludge (R3) at hydraulic retention times (HRT) between 3 and 24h. Maximum 1,3-PDO yield (0.52molmol(-1)) and productivity (57gL(-1)d(-1)) were achieved in R1 at HRTs of 12 and 3h, respectively. DGGE profiling of PCR-amplified 16S rRNA gene fragments showed that variations in the HRT had a critical impact in the dominant community of microorganisms. However, no appreciable differences in the bacterial population were observed between R2 and R3 at low HRTs. Production of H2 was observed at the beginning of the operation, but no methane production was observed. This study proves the feasibility of 1,3-PDO production in EGSB reactors and represents a novel strategy to valorise glycerol generated in the biodiesel industry. PMID:24413479

  8. THE EFFECT OF POWERED ACTIVATED CARBON IN A PETROLEUM REFINERY ACTIVATED SLUDGE TREATMENT SYSTEM

    EPA Science Inventory

    The purpose of this research program was to determine the effect of the addition of powdered activated carbon (PAC) to refinery activated sludge systems. Bench-scale and full-scale tests were performed. A wide range of PAC concentrations and sludge ages were evaluated. Bench-scal...

  9. EVALUATION OF FULL SCALE ACTIVATED SLUDGE SYSTEMS UTILIZING POWDERED ACTIVATED CARBON ADDITION WITH WET AIR REGENERATION

    EPA Science Inventory

    The addition of powdered activated carbon (PAC) to activated sludge systems is a proven method of wastewater treatment. Of eleven POTWs in the U.S. that were designed for PAC use, ten included wet air regeneration (WAR) for the destruction of secondary sludge solids and recovery ...

  10. Microscopic Analysis of Plankton, Periphyton, and Activated Sludge. Training Manual.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC. Office of Water Programs.

    This manual is intended for professional personnel in the fields of water pollution control, limnology, water supply and waste treatment. Primary emphasis is given to practice in the identification and enumeration of microscopic organisms which may be encountered in water and activated sludge. Methods for the chemical and instrumental evaluation…

  11. Basic Activated Sludge. Training Module 2.115.2.77.

    ERIC Educational Resources Information Center

    Kirkwood Community Coll., Cedar Rapids, IA.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with operation of activated sludge wastewater treatment plants. Included are objectives, instructor guides, student handouts, and transparency masters. This is the first of a three module series and considers definition of terms, design…

  12. Intermediate Activated Sludge. Training Module 2.116.3.77.

    ERIC Educational Resources Information Center

    Kirkwood Community Coll., Cedar Rapids, IA.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with operation of activated sludge wastewater treatment plants. Included are objectives, instructor guides, student handouts and transparency masters. This is the second level of a three module series and considers aeration devices,…

  13. TOP-FEED VACUUM FILTRATION OF WASTE-ACTIVATED SLUDGE

    EPA Science Inventory

    A side-by-side comparison of a conventional bottom-feed vacuum filter and a prototype top-feed vacuum filter was conducted. Thickened, waste-activated sludge at approximately 1.8 percent feed solids concentration and conditioned with ferric chloride was dewatered on two filters 1...

  14. SAFETY ASPECTS OF OXYGEN AERATION ACTIVATED SLUDGE SYSTEMS

    EPA Science Inventory

    This project was carried out to assess the impact of the use of oxygen and oxygen-enriched air for aeration of activated sludge systems on the safety of municipal waste-water treatment plants and their personnel. The tasks included (1) determination of oxygen combustion hazards f...

  15. ACTIVATED SLUDGE CLARIFIERS: DESIGN REQUIREMENTS AND RESEARCH PRIORITIES

    EPA Science Inventory

    The literature review of 320 references was conducted in an EPA-funded project to identify the needs for further research on activated sludge clarifier design and performance. The findings were summarized in a report and used as a basis of a 3-day research needs symposium. The pr...

  16. EVALUATION OF AN ACTIVATED SLUDGE SECONDARY CLARIFIER DISTRIBUTED INLET

    EPA Science Inventory

    Secondary clarifiers are crucial to the overall performance of the activated sludge process. Research over the last 40 years indicates that density currents are factors which degrade clarifier performance when not considered in design. However, present designs of most center-feed...

  17. FEASIBILITY OF TREATING SEPTIC TANK WASTE BY ACTIVATED SLUDGE

    EPA Science Inventory

    The objective of the study reported herein was to evaluate the impact of household septic tank wastes on municipal activated sludge treatment plants. Septage addition was evaluated on a continuous basis over a four-month period in a 7500 l/day (1980 gpd) pilot plant. The septage ...

  18. Fate and effects of methylene chloride in activated sludge.

    PubMed

    Klecka, G M

    1982-09-01

    Activated sludge obtained from a municipal wastewater treatment plant was acclimated to methylene chloride at concentrations between 1 and 100 mg/liter by continuous exposure to the compound for 9 to 11 days. Acclimated cultures were shown to mineralize methylene chloride to carbon dioxide and chloride. Rates of methylene chloride degradation were 0.14, 2.3, and 7.4 mg of CH2Cl2 consumed per h per g of mixed-liquor suspended solids for cultures incubated in the presence of 1, 10, and 100 mg/liter, respectively. Concentrations of methylene chloride between 10 and 1,000 mg/liter had no significant effect on O2 consumption or glucose metabolism by activated sludge. A hypothetical model was developed to examine the significance of volatilization and biodegradation for the removal of methylene chloride from an activated sludge reactor. Application of the model indicated that the rate of biodegradation was approximately 12 times greater than the rate of volatilization. Thus, biodegradation may be the predominant process determining the fate of methylene chloride in activated sludge systems continuously exposed to the compound. PMID:7138008

  19. Operational Control Procedures for the Activated Sludge Process: Appendix.

    ERIC Educational Resources Information Center

    West, Alfred W.

    This document is the appendix for a series of documents developed by the National Training and Operational Technology Center describing operational control procedures for the activated sludge process used in wastewater treatment. Categories discussed include: control test data, trend charts, moving averages, semi-logarithmic plots, probability…

  20. Advanced Activated Sludge. Training Module 2.117.4.77.

    ERIC Educational Resources Information Center

    Kirkwood Community Coll., Cedar Rapids, IA.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with operation of activated sludge wastewater treatment plants. Included are objectives, instructor guides, student handouts and transparency masters. This is the third level of a three module series and considers design and operation…

  1. Activated Sludge. Instructor's Guide. Biological Treatment Process Control.

    ERIC Educational Resources Information Center

    Boe, Owen K.

    This instructor's guide contains the materials needed to teach a seven-lesson unit on activated sludge. These materials include an overview of the unit, lesson plans, lecture outlines (keyed to slides designed for use with the lessons), student worksheets for each of the seven lessons (with answers), and two copies of a final quiz (with and…

  2. Fate and effects of methylene chloride in activated sludge.

    PubMed Central

    Klecka, G M

    1982-01-01

    Activated sludge obtained from a municipal wastewater treatment plant was acclimated to methylene chloride at concentrations between 1 and 100 mg/liter by continuous exposure to the compound for 9 to 11 days. Acclimated cultures were shown to mineralize methylene chloride to carbon dioxide and chloride. Rates of methylene chloride degradation were 0.14, 2.3, and 7.4 mg of CH2Cl2 consumed per h per g of mixed-liquor suspended solids for cultures incubated in the presence of 1, 10, and 100 mg/liter, respectively. Concentrations of methylene chloride between 10 and 1,000 mg/liter had no significant effect on O2 consumption or glucose metabolism by activated sludge. A hypothetical model was developed to examine the significance of volatilization and biodegradation for the removal of methylene chloride from an activated sludge reactor. Application of the model indicated that the rate of biodegradation was approximately 12 times greater than the rate of volatilization. Thus, biodegradation may be the predominant process determining the fate of methylene chloride in activated sludge systems continuously exposed to the compound. PMID:7138008

  3. PILOT PLANT EVALUATION OF ALTERNATIVE ACTIVATED SLUDGE SYSTEMS

    EPA Science Inventory

    Step feed, plug flow and complete mix activated sludge systems were compared on a pilot plant scale under similar operating conditions with the same municipal wastewater. The process loading to each system was varied over a wide range during the course of the investigation. Exten...

  4. BIOLOGICALLY ENHANCED OXYGEN TRANSFER IN THE ACTIVATED SLUDGE PROCESS (JOURNAL)

    EPA Science Inventory

    Biologically enhanced oxgyen transfer has been a hypothesis to explain observed oxygen transfer rates in activated sludge systems that were well above that predicted from aerator clean-water testing. The enhanced oxygen transfer rates were based on tests using BOD bottle oxygen ...

  5. Heavy metals and adsorbents effects on activated sludge microorganisms.

    PubMed

    Ong, S A; Lim, P E; Seng, C E

    2004-01-01

    The sorption of Cu(II) and Cd(II) from synthetic solution by powdered activated carbon (PAC), biomass, rice husk (RH) and activated rice husk (ARH) were investigate under batch conditions. After activated by concentrated nitric acid for 15 hours at 60-65 degrees C, the adsorption capacity for RH was increased. The adsorbents arranged in the increasing order of adsorption capacities to the Langmuir Q degree parameter were biomass > PAC > ARH > RH. The addition of adsorbents in base mix solution had increased the specific oxygen uptake rate (SOUR) activated sludge microorganisms with and without the presence of metals. The increased of SOUR were due to the ability of PAC and RH in reducing the inhibitory effect of metals on microorganisms and provide a reaction site between activated sludge microorganisms and substrates. PMID:15141467

  6. EVALUATION OF ACTIVATED BIOFILTRATION AND ACTIVATED BIOFILTRATION/ACTIVATED SLUDGE TECHNOLOGIES

    EPA Science Inventory

    The paper presents the results of a review and investigation of the activated biofilter (ABF) and activated biofilter/activated sludge (ABF/AS) technologies and a review of operating records of several municipal plants in the U.S. using these technologies. The overall objective o...

  7. Degradation of a model azo dye in submerged anaerobic membrane bioreactor (SAMBR) operated with powdered activated carbon (PAC).

    PubMed

    Baêta, B E L; Luna, H J; Sanson, A L; Silva, S Q; Aquino, S F

    2013-10-15

    This work investigated the anaerobic degradation of the model azo dye Remazol Yellow Gold RNL in an upflow anaerobic sludge blanket reactor (UASB) and two submerged anaerobic membrane (SAMBR) bioreactors, one of which (SAMBR-1) was operated with powdered activated carbon (PAC) in its interior. The reactors were operated at 35 °C with a hydraulic retention time of 24 h in three operational phases, aimed to assess the effect of external sources of carbon (glucose) or redox mediator (yeast extract) on the removal or color and organic matter. The results showed that removal efficiencies of COD (73-94%) and color (90-94%) were higher for SAMBR-1 when compared to SAMBR-2 (operated without PAC) and UASB reactors. In addition, the presence of PAC in SAMBR-1 increased reactor stability, thereby leading to a lower accumulation of volatile fatty acids (VFA). The microfiltration membrane was responsible for an additional removal of ~50% of soluble residual COD in the form of VFA, thus improving permeate quality. On its turn, PAC exhibited the ability to adsorb byproducts (aromatic amines) of azo dye degradation as well as to act as source of immobilized redox mediator (quinone groups on its surface), thereby enhancing color removal. PMID:23810998

  8. Microbial Community Structure of Activated Sludge in Treatment Plants with Different Wastewater Compositions.

    PubMed

    Shchegolkova, Nataliya M; Krasnov, George S; Belova, Anastasia A; Dmitriev, Alexey A; Kharitonov, Sergey L; Klimina, Kseniya M; Melnikova, Nataliya V; Kudryavtseva, Anna V

    2016-01-01

    Activated sludge (AS) plays a crucial role in the treatment of domestic and industrial wastewater. AS is a biocenosis of microorganisms capable of degrading various pollutants, including organic compounds, toxicants, and xenobiotics. We performed 16S rRNA gene sequencing of AS and incoming sewage in three wastewater treatment plants (WWTPs) responsible for processing sewage with different origins: municipal wastewater, slaughterhouse wastewater, and refinery sewage. In contrast to incoming wastewater, the taxonomic structure of AS biocenosis was found to become stable in time, and each WWTP demonstrated a unique taxonomic pattern. Most pathogenic microorganisms (Streptococcus, Trichococcus, etc.), which are abundantly represented in incoming sewage, were significantly decreased in AS of all WWTPs, except for the slaughterhouse wastewater. Additional load of bioreactors with influent rich in petroleum products and organic matter was associated with the increase of bacteria responsible for AS bulking and foaming. Here, we present a novel approach enabling the prediction of the metabolic potential of bacterial communities based on their taxonomic structures and MetaCyc database data. We developed a software application, XeDetect, to implement this approach. Using XeDetect, we found that the metabolic potential of the three bacterial communities clearly reflected the substrate composition. We revealed that the microorganisms responsible for AS bulking and foaming (most abundant in AS of slaughterhouse wastewater) played a leading role in the degradation of substrates such as fatty acids, amino acids, and other bioorganic compounds. Moreover, we discovered that the chemical, rather than the bacterial composition of the incoming wastewater was the main factor in AS structure formation. XeDetect (freely available: https://sourceforge.net/projects/xedetect) represents a novel powerful tool for the analysis of the metabolic capacity of bacterial communities. The tool will

  9. Microbial Community Structure of Activated Sludge in Treatment Plants with Different Wastewater Compositions

    PubMed Central

    Shchegolkova, Nataliya M.; Krasnov, George S.; Belova, Anastasia A.; Dmitriev, Alexey A.; Kharitonov, Sergey L.; Klimina, Kseniya M.; Melnikova, Nataliya V.; Kudryavtseva, Anna V.

    2016-01-01

    Activated sludge (AS) plays a crucial role in the treatment of domestic and industrial wastewater. AS is a biocenosis of microorganisms capable of degrading various pollutants, including organic compounds, toxicants, and xenobiotics. We performed 16S rRNA gene sequencing of AS and incoming sewage in three wastewater treatment plants (WWTPs) responsible for processing sewage with different origins: municipal wastewater, slaughterhouse wastewater, and refinery sewage. In contrast to incoming wastewater, the taxonomic structure of AS biocenosis was found to become stable in time, and each WWTP demonstrated a unique taxonomic pattern. Most pathogenic microorganisms (Streptococcus, Trichococcus, etc.), which are abundantly represented in incoming sewage, were significantly decreased in AS of all WWTPs, except for the slaughterhouse wastewater. Additional load of bioreactors with influent rich in petroleum products and organic matter was associated with the increase of bacteria responsible for AS bulking and foaming. Here, we present a novel approach enabling the prediction of the metabolic potential of bacterial communities based on their taxonomic structures and MetaCyc database data. We developed a software application, XeDetect, to implement this approach. Using XeDetect, we found that the metabolic potential of the three bacterial communities clearly reflected the substrate composition. We revealed that the microorganisms responsible for AS bulking and foaming (most abundant in AS of slaughterhouse wastewater) played a leading role in the degradation of substrates such as fatty acids, amino acids, and other bioorganic compounds. Moreover, we discovered that the chemical, rather than the bacterial composition of the incoming wastewater was the main factor in AS structure formation. XeDetect (freely available: https://sourceforge.net/projects/xedetect) represents a novel powerful tool for the analysis of the metabolic capacity of bacterial communities. The tool will

  10. Improve bio-activity of anaerobic sludge by low energy ultrasound.

    PubMed

    Zhu, Yichun; Li, Xin; Du, Maoan; Liu, Zuwen; Luo, Hui; Zhang, Tao

    2015-01-01

    This research focused on ultrasound-enhanced bio-activity of anaerobic sludge. Low energy ultrasound irradiation can increase the bio-activity of anaerobic sludge. Ultrasonic parameter, characteristics of anaerobic sludge and experimental conditions are important parameters which affect the enhancement effect on anaerobic sludge. In order to assess the effects of characteristics of anaerobic sludge and experimental conditions on ultrasonic irradiation of anaerobic sludge, experiments with different characteristics of anaerobic sludge were carried out and analyzed with the content of coenzyme F420 and dehydrogenase activity (DHA). The results showed that anaerobic sludge bio-activity was impacted by the initial temperature, initial chemical oxygen demand (COD), sludge concentration, and stirring during the ultrasonic process. Optimal performance was achieved when sound frequency, power density, and ultrasonic irradiation period was 20 kHz, 0.1 W/mL, and 10 min, respectively, under which the wastewater COD removal efficiency was increased by 12.9 percentage points. The results indicated that low temperature could affect the anaerobic sludge irradiation effect, while intermittent stirring could enhance the bio-activity of anaerobic sludge irradiation effect and low substrate concentration improved anaerobic sludge activity by ultrasound. PMID:26676010

  11. Suitability of Sludge Biotic Index (SBI), Sludge Index (SI) and filamentous bacteria analysis for assessing activated sludge process performance: the case of piggery slaughterhouse wastewater.

    PubMed

    Pedrazzani, Roberta; Menoni, Laura; Nembrini, Stefano; Manili, Livia; Bertanza, Giorgio

    2016-07-01

    Piggery slaughterhouse wastewater poses serious issues in terms of disposal feasibility and environmental impact, due to its huge organic load and variability. It is commonly treated by means of activated sludge processes, whose performance, in case of municipal wastewater, can be monitored by means of specific analyses, such as Sludge Biotic Index (SBI), Sludge Index (SI) and floc and filamentous bacteria observation. Therefore, this paper was aimed at assessing the applicability of these techniques to piggery slaughterhouse sewage. A plant located in Northern Italy was monitored for 1 year. Physical, chemical and operation parameters were measured; the activated sludge community (ciliates, flagellates, amoebae and small metazoa) was analysed for calculating SBI and SI. Floc and filamentous bacteria were examined and described accordingly with internationally adopted criteria. The results showed the full applicability of the studied techniques for optimizing the operation of a piggery slaughterhouse wastewater treatment plant. PMID:27072565

  12. Evaluation-of soil enzyme activities as soil quality indicators in sludge-amended soils.

    PubMed

    Dindar, Efsun; Şağban, Fatma Olcay Topaç; Başkaya, Hüseyin Savaş

    2015-07-01

    Soil enzymatic activities are commonly used as biomarkers of soil quality. Several organic and inorganic compounds found in municipal wastewater sludges can possibly be used as fertilizers. Monitoring and evaluating the quality of sludge amended soils with enzyme activities accepted as a beneficial practice with respect to sustainable soil management. In the present study, variation of some enzyme activities (Alkaline phosphatase, dehydrogenase, urease and beta-glucosidase activities) in soils amended with municipal wastewater sludge at different application rates (50, 100 and 200 t ha(-1) dry sludge) was evaluated. Air dried sludge samples were applied to soil pots and sludge-soil mixtures were incubated during a period of three months at 28 degrees C. The results of the study showed that municipal wastewater sludge amendment apparently increased urease, dehydrogenase, alkaline phosphatase and P-glucosidase activities in soil by 48-70%, 14-47%, 33-66% and 9-14%, respectively. The maximum activity was generally observed in sludge amended soil with dose of 200 t ha(-1). Urease activity appeared to be a better indicator of soil enhancement with wastewater sludge, as its activity was more strongly increased by sludge amendment. Accordingly, urease activity is suggested to be soil quality indicator best suited for measuring existing conditions and potential changes in sludge-amended soil. PMID:26364470

  13. A pilot study of anaerobic membrane digesters for concurrent thickening and digestion of waste activated sludge (WAS).

    PubMed

    Dagnew, Martha; Parker, Wayne J; Seto, Peter

    2010-01-01

    The increased interest in biomass energy provides incentive for the development of efficient and high throughput digesters such as anaerobic membrane bioreactors (AnMBRs) to stabilize waste activated sludge (WAS). This paper presents the results of a pilot and short term filtration study that was conducted to assess the performance of AnMBRs when treating WAS at a 15 day hydraulic retention time (HRT) and 30 day sludge retention time (SRT) in comparison to two conventional digesters running at 15 (BSR-15) and 30 days (BSR-30) HRT/SRT. At steady state, the AnMBR digester showed a slightly higher volatile solids (VS) destruction of 48% in comparison to 44% and 35.3% for BSR-30 and BSR-15, respectively. The corresponding values of specific methane production were 0.32, 0.28 and 0.21 m(3) CH(4)/kg of VS fed. Stable membrane operation at an average flux of 40+/-3.6 LM(-2 )H(-1) (LMH) was observed when the digester was fed with a polymer-dosed thickened waste activated sludge (TWAS) and digester total suspended solids (TSS) concentrations were less than 15 gL(-1). Above this solids concentration a flux decline to 24.1+/-2.0 LM(-2) H(-1) was observed. Short term filtration tests conducted using sludge fractions of a 9.7 and 17.1 gL(-1) TSS sludge indicated 84 and 70% decline in filtration performance to be associated with the supernatant fraction of the sludge. At a higher sludge concentration, the introduction of unique fouling control strategy to tubular membranes, a relaxed mode of operation (i.e. 5 minutes permeation and 1 minute relaxation by) significantly increased the flux from 23.8+/-1.1 to 37.8+/-2.3 LMH for a neutral membrane and from 25.7+/-1.1 to 44.9+/-2.9 LMH for a negatively charged membrane. The study clearly indicates that it is technically feasible to employ AnMBRs to achieve a substantial reduction in digester volumes. PMID:20351424

  14. Method for Adenosine 5′-Triphosphate Measurement on Coke Waste Activated Sludge

    PubMed Central

    Russell, James; Gauthier, Joseph J.

    1978-01-01

    Measurement of adenosine 5′-triphosphate (ATP) in coke waste activated sludge can provide a simple method for estimating the levels of viable microbes in the sludge. However, the presence of inhibitors such as phenol in the sludge interferes when the luciferin-luciferase method is used to measure ATP. These inhibiting substances can be removed from the sludge before extraction of ATP by washing the cells with dilute sodium dodecyl sulfate. PMID:16345281

  15. Biodegradation of benzotriazoles and hydroxy-benzothiazole in wastewater by activated sludge and moving bed biofilm reactor systems.

    PubMed

    Mazioti, Aikaterini A; Stasinakis, Athanasios S; Pantazi, Ypapanti; Andersen, Henrik R

    2015-09-01

    Two laboratory scale fully aerated continuous flow wastewater treatment systems were used to compare the removal of five benzotriazoles and one benzothiazole by suspended and attached growth biomass. The activated sludge system was operated under low organic loading conditions. The moving bed biofilm reactor (MBBR) system consisted of two serially connected reactors filled with K3-biocarriers. It was either operated under low or high organic loading conditions. Target compounds were removed partially and with different rates in tested systems. For MBBR, increased loading resulted in significantly lower biodegradation for 4 out of 6 examined compounds. Calculation of specific removal rates (normalized to biomass) revealed that attached biomass had higher biodegradation potential for target compounds comparing to suspended biomass. Clear differences in the biodegradation ability of attached biomass grown in different bioreactors of MBBR systems were also observed. Batch experiments showed that micropollutants biodegradation by both types of biomass is co-metabolic. PMID:26093257

  16. Experimental and CFD simulation studies of wall shear stress for different impeller configurations and MBR activated sludge.

    PubMed

    Ratkovich, N; Chan, C C V; Bentzen, T R; Rasmussen, M R

    2012-01-01

    Membrane bioreactors (MBRs) have been used successfully in biological wastewater treatment for effective solids-liquid separation. However, a common problem encountered with MBR systems is fouling of the membrane resulting in frequent membrane cleaning and replacement which makes the system less appealing for full-scale applications. It has been widely demonstrated that the filtration performances in MBRs can be improved by understanding the shear stress over the membrane surface. Modern tools such as computational fluid dynamics (CFD) can be used to diagnose and understand the shear stress in an MBR. Nevertheless, proper experimental validation is required to validate CFD simulation. In this work experimental measurements of shear stress induced by impellers at a membrane surface were made with an electrochemical approach and the results were used to validate CFD simulations. As good results were obtained with the CFD model (<9% error), it was extrapolated to include the non-Newtonian behaviour of activated sludge. PMID:22592479

  17. Proteomics reliability for micropollutants degradation insight into activated sludge systems.

    PubMed

    Buttiglieri, Gianluigi; Collado, Neus; Casas, Nuria; Comas, Joaquim; Rodriguez-Roda, Ignasi

    2015-01-01

    Little information is available on pharmaceutical trace compounds degradation pathways in wastewater. The potential of the proteomics approach has been evaluated to extract information on activated sludge microbial metabolism in degrading a trace concentration of a pharmaceutical compound (ibuprofen). Ibuprofen is one of the most consumed pharmaceuticals, measured in wastewater at very high concentrations and, despite its high removal rates, found in different environmental compartments. Aerated and completely mixed activated sludge batch tests were spiked with ibuprofen at 10 and 1,000 μg L(-1). Ibuprofen concentrations were determined in the liquid phase: 100% removal was observed and the kinetics were estimated. The solid phase was sampled for proteomics purposes. The first objective was to apply proteomics to evaluate protein profile variations in a complex matrix such as activated sludge. The second objective was to determine, at different ibuprofen concentrations, which proteins followed pre-defined trends. No newly expressed proteins were found. Nonetheless, the obtained results suggest that proteomics itself is a promising methodology to be applied in this field. Statistical and comparative studies analyses provided, in fact, useful information on biological reproducibility and permitted us to detect 62 proteins following coherent and plausible expected trends in terms of presence and intensity change. PMID:26360747

  18. Micropollutant degradation via extracted native enzymes from activated sludge.

    PubMed

    Krah, Daniel; Ghattas, Ann-Kathrin; Wick, Arne; Bröder, Kathrin; Ternes, Thomas A

    2016-05-15

    A procedure was developed to assess the biodegradation of micropollutants in cell-free lysates produced from activated sludge of a municipal wastewater treatment plant (WWTP). This proof-of-principle provides the basis for further investigations of micropollutant biodegradation via native enzymes in a solution of reduced complexity, facilitating downstream protein analysis. Differently produced lysates, containing a variety of native enzymes, showed significant enzymatic activities of acid phosphatase, β-galactosidase and β-glucuronidase in conventional colorimetric enzyme assays, whereas heat-deactivated controls did not. To determine the enzymatic activity towards micropollutants, 20 compounds were spiked to the cell-free lysates under aerobic conditions and were monitored via LC-ESI-MS/MS. The micropollutants were selected to span a wide range of different biodegradabilities in conventional activated sludge treatment via distinct primary degradation reactions. Of the 20 spiked micropollutants, 18 could be degraded by intact sludge under assay conditions, while six showed reproducible degradation in the lysates compared to the heat-deactivated negative controls: acetaminophen, N-acetyl-sulfamethoxazole (acetyl-SMX), atenolol, bezafibrate, erythromycin and 10,11-dihydro-10-hydroxycarbamazepine (10-OH-CBZ). The primary biotransformation of the first four compounds can be attributed to amide hydrolysis. However, the observed biotransformations in the lysates were differently influenced by experimental parameters such as sludge pre-treatment and the addition of ammonium sulfate or peptidase inhibitors, suggesting that different hydrolase enzymes were involved in the primary degradation, among them possibly peptidases. Furthermore, the transformation of 10-OH-CBZ to 9-CA-ADIN was caused by a biologically-mediated oxidation, which indicates that in addition to hydrolases further enzyme classes (probably oxidoreductases) are present in the native lysates. Although the

  19. Preparation of activated carbon from wet sludge by electrochemical-NaClO activation.

    PubMed

    Miao, Chen; Ye, Caihong; Zhu, Tianxing; Lou, Ziyang; Yuan, Haiping; Zhu, Nanwen

    2014-01-01

    Activated carbon (AC) from sludge is one potential solution for sewage sludge disposal, while the drying sludge is cost and time consuming for preparation. AC preparation from the wet sludge with electrochemical-NaClO activation was studied in this work. Three pretreatment processes, i.e. chemical activation, electrolysis and electrochemical-reagent reaction, were introduced to improve the sludge-derived AC properties, and the optimum dosage of reagent was tested from the 0.1:1 to 1:1 (mass rate, reagent:dried sludge). It was shown that the electrochemical-NaClO preparation is the best method under the test conditions, in which AC has the maximum Brunauer, Emmett and Teller area of 436 m²/g at a mass ratio of 0.7. Extracellular polymeric substances in sludge can be disintegrated by electrochemical-NaClO pretreatment, with a disintegration degree of more than 45%. The percentage of carbon decreased from 34.16 to 8.81 after treated by electrochemical-NaClO activation. Fourier transform infrared spectra showed that a strong C-Cl stretching was formed in electrochemical-NaClO prepared AC. The maximum adsorption capacity of AC reaches 109 mg/g on MB adsorption experiment at pH 10 and can be repeated for three times with high removal efficiency after regeneration. PMID:25176302

  20. Substrate consumption and excess sludge reduction of activated sludge in the presence of uncouplers: a modeling approach.

    PubMed

    Xie, Wen-Ming; Ni, Bing-Jie; Sheng, Guo-Ping; Yu, Han-Qing; Yang, Min

    2010-02-01

    A mathematical model with a consideration of energy spilling is developed to describe the activated sludge in the presence of different levels of metabolic uncouplers. The consumption of substrate and oxygen via energy spilling process is modeled with a Monod term, which is dependent on substrate and inhibitor. The sensitivity of the developed model is analyzed. Three parameters, maximum specific growth rate (micro(max)), energy spilling coefficient (q(max)), and sludge yield coefficient (Y(H)) are estimated with experimental data of different studies. The values of micro(max), q(max), and Y(H) are found to be 6.72 day(-1), 5.52 day(-1), and 0.60 mg COD mg(-1) COD for 2, 4-dinitrophenol and 7.20 day(-1), 1.58 day(-1), and 0.62 mg COD mg(-1) COD for 2, 4-dichlorophenol. Substrate degradation and sludge yield could be predicted with this model. The activated sludge process in the presence of uncouplers that is described more reasonably by the new model with a consideration of energy spilling. The effects of uncouplers on substrate consumption inhibition and excess sludge reduction in activated sludge are quantified with this model. PMID:19898844

  1. Investigating the fate of activated sludge extracellular proteins in sludge digestion using sodium dodecyl sulfate polyacrylamide gel electrophoresis.

    PubMed

    Park, Chul; Helm, Richard F; Novak, John T

    2008-12-01

    The fate of activated sludge extracellular proteins in sludge digestion was investigated using three different cation-associated extraction methods and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Extraction methods used were the cation exchange resin (CER) method for extracting calcium (Ca2+) and magnesium (Mg2+), sulfide extraction for removing iron, and base treatment (pH 10.5) for dissolving aluminum. Extracellular polymeric substances extracted were then subjected to SDS-PAGE, and the resultant protein profiles were examined before and after sludge digestion. The SDS-PAGE results showed that three methods led to different SDS-PAGE profiles for both undigested and digested sludges. The results further revealed that CER-extracted proteins remained mainly undegraded in anaerobic digestion, but were degraded in aerobic digestion. While the fate of sulfide- and base-extracted proteins was not clear for aerobic digestion, their changes in anaerobic digestion were elucidated. Most sulfide-extracted proteins were removed by anaerobic digestion, while the increase in protein band intensity and diversity was observed for base-extracted proteins. These results suggest that activated sludge flocs contain different fractions of proteins that are distinguishable by their association with certain cations and that each fraction undergoes different fates in anaerobic and aerobic digestion. The proteins that were resistant to degradation and generated during anaerobic digestion were identified by liquid chromatography tandem mass spectrometry. Protein identification results and their putative roles in activated sludge and anaerobic digestion are discussed in this study. PMID:19146099

  2. Correlation between microbial diversity and toxicity of sludge treating synthetic wastewater containing 4-chlorophenol in sequencing batch reactors.

    PubMed

    Zhao, Jianguo; Chen, Xiurong; Bao, Linlin; Bao, Zheng; He, Yixuan; Zhang, Yuying; Li, Jiahui

    2016-06-01

    The relationship between microbial diversity and sludge toxicity in the biotreatment of refractory wastewater was investigated. Synthetic wastewater containing 4-chlorophenol (4-CP) was treated by an activated sludge using a sequencing batch bioreactor (SBR). At the end of a single SBR cycle, a stable operation stage was reached when the 4-CP was not detected both in aqueous and sludge phases and the effluent COD was maintained at approximately 70 mg L(-1) for the blank and control sludge groups. Then, the diversity of the microorganisms and the sludge toxicity were measured. The results showed that the Microtox acute toxicity of the control sludge was higher than those of the blank sludge. The difference analysis of the microbial diversity between the blank and control sludge indicated that the sludge toxicity was closely related to microbial diversity. PMID:27016808

  3. Effects of total solids content on waste activated sludge thermophilic anaerobic digestion and its sludge dewaterability.

    PubMed

    Wang, Tianfeng; Chen, Jie; Shen, Honglang; An, Dong

    2016-10-01

    The role of total solids content on sludge thermophilic anaerobic digestion was investigated in batch reactors. A range of total solids content from 2% to 10% was evaluated with two replicates. The lowest inhibitory concentration for free ammonia and total ammonia of sludge thermophilic anaerobic digestion was 110.9-171.4mg/L and 1313.1-1806.7mg/L, respectively. The volumetric biogas production rate increased with increasing of total solids content, but the corresponding biogas yield per gram volatile solid decreased. The result of normalized capillary suction time indicated that the dewaterability of digested sludge at high total solids content was poor, while solid content of sediment obtained by centrifuging sludge at 2000g for 10min increased with increasing of total solids content of sludge. The results suggest that thickened sludge mixed with dewatered sludge at an appropriate ratio could get high organic loading rate, high biogas yield and adequate dewatering effort. PMID:26897469

  4. Enhancement of As(V) adsorption onto activated sludge by methylation treatment.

    PubMed

    Kang, So-Young; Kim, Dong-Wook; Kim, Kyoung-Woong

    2007-08-01

    Biosorption properties of arsenate [As(V)] onto activated sludge were investigated in batch systems. The adsorption of As(V) onto sludge increased from 23 to 266 microg/g dry weight through the methylation of the activated sludge. This increase resulted from neutralization of carboxylic groups via the methylation process. The pH effect of As(V) uptake was also investigated and As(V) adsorption by methylated sludge decreased significantly at high pH (pH > 11) due to competition between As(V) and OH(-) ions for binding sites distributed on sludge surfaces. In contrast, low pH favored As(V) adsorption by methylated sludge because of the elevated quantities of positively charged functional groups. The results suggest that methylated activated sludge may provide promising applications for the simultaneous removal and separation of As(V) from aqueous effluents. PMID:17505894

  5. Effect of dissolved organic material and cations on freeze-thaw conditioning of activated and alum sludges.

    PubMed

    Ormeci, B; Vesilind, P A

    2001-12-01

    Freeze-thaw conditioning effectively dewaters alum and activated sludges, but it works better on alum sludge than it does on activated sludge. The main difference between alum sludge and activated sludge is that activated sludge has high concentrations of both dissolved organic material and ions. Dissolved organic material and ions may possibly alter the freezing process and decrease the effectiveness of freeze-thaw conditioning on activated sludge. The objective of this study is to investigate the effect of dissolved organic material and cations on freeze-thaw conditioning of sludges, and to improve the effectiveness of freeze-thaw conditioning on activated sludge. The results of this study show that although protein, carbohydrate and cation concentrations in activated sludge supernatant are initially high, they dramatically increase after freeze-thaw conditioning. The increase is likely to come from the release of extracellular and intracellular material to sludge supernatant. The observed increase in the DNA concentration in activated sludge supernatant after freeze-thaw conditioning indicates that freeze-thaw causes cell disruption. Alum sludge supernatant, on the other hand, initially contains low concentrations of proteins, carbohydrates and cations which do not noticeably change after freeze-thaw conditioning. When ECPs (extracellular polymers) and cations are extracted from activated sludge before freeze-thaw conditioning. the sludge settles and dewaters better after the freeze-thaw. The resulting aggregates are smaller and denser resembling the "coffee ground" aggregates of alum sludge. PMID:11763031

  6. Methanospirillum stamsii sp. nov., a psychrotolerant, hydrogenotrophic, methanogenic archaeon isolated from an anaerobic expanded granular sludge bed bioreactor operated at low temperature.

    PubMed

    Parshina, Sofiya N; Ermakova, Anna V; Bomberg, Malin; Detkova, Ekaterina N

    2014-01-01

    A psychrotolerant hydrogenotrophic methanogen, strain Pt1, was isolated from a syntrophic propionate-oxidizing methanogenic consortium obtained from granulated biomass of a two-stage low-temperature (3-8 °C) anaerobic expanded granular sludge bed (EGSB) bioreactor, fed with a mixture of volatile fatty acids (VFAs) (acetate, propionate and butyrate). The strain was strictly anaerobic, and cells were curved rods, 0.4-0.5×7.5-25 µm, that sometimes formed wavy filaments from 25 to several hundred micrometres in length. Cells stained Gram-negative and were non-sporulating. They were gently motile by means of tufted flagella. The strain grew at 5-37 °C (optimum at 20-30 °C), at pH 6.0-10 (optimum 7.0-7.5) and with 0-0.3 M NaCl (optimum 0 M NaCl). Growth and methane production was found with H2/CO2 and very weak growth with formate. Acetate and yeast extract stimulated growth, but were not essential. The G+C content of the DNA of strain Pt1 was 40 mol%. Phylogenetic analysis based on 16S rRNA gene sequences revealed that strain Pt1 was a member of the genus Methanospirillum and showed 97.5 % sequence similarity to Methanospirillum hungatei JF1(T) and 94 % sequence similarity to Methanospirillum lacunae Ki8-1(T). DNA-DNA hybridization of strain Pt1 with Methanospirillum hungatei JF1(T) revealed 39 % relatedness. On the basis of its phenotypic characteristics and phylogenetic position, strain Pt1 is a representative of a novel species of the genus Methanospirillum, for which the name Methanospirillum stamsii sp. nov. is proposed. The type strain is Pt1(T) ( = DSM 26304(T) = VKM B-2808(T)). PMID:24048867

  7. An activated sludge model based on activated sludge model number 3 for full-scale wastewater treatment plant simulation.

    PubMed

    Fan, Ji; Lu, Shu-Guang; Qiu, Zhao-fu; Wang, Xiao-Xia; Li, Wen-Zhen

    2009-06-01

    A modified model based on the activated sludge model no. 3 was established to simulate a full-scale municipal wastewater treatment plant in Shanghai, China. The activated sludge model no. 3 was modified to describe the simultaneous storage and growth processes occurring in activated sludge systems under aerobic and anoxic conditions. The mechanism of soluble microbial product formation and degradation by microorganisms was considered in this proposed model. Three months simulation was conducted including soluble chemical oxygen demand, NH4(+)-N, NO(X)(-)-N and T-N parameters, and compared with measured data from the Quyang wastewater treatment plant. Results indicated that the calculated effluent chemical oxygen demand and NH4(+)-N using this proposed model were in good agreement with the measured data. Results also showed that besides inert soluble organic matter contributing to the effluent chemical oxygen demand, soluble microbial products played an important part in the effluent chemical oxygen demand and, therefore, demonstrated that these products composed an important portion of effluent soluble chemical oxygen demand in wastewater treatment plants and should not be neglected. PMID:19705601

  8. Microbiological Analysis of an Active Pilot-Scale Mobile Bioreactor Treating Organic Contaminants

    SciTech Connect

    Brigmon, R.L.

    1997-11-26

    Samples were obtained for microbiological analysis from a granular activated carbon fluidized bed bioreactor (GAC-FBR). This GAC-FBR was in operation at a former manufactured gas plant (MGP) Site in Augusta Georgia for in situ groundwater bioremediation of organics. The samples included contaminated site groundwater, GAC-FBR effluent, and biofilm coated granular activated carbon at 5, 9, and 13 feet within the GAC-FBR column. The objective of this analysis was to correlate contaminant removal with microbiological activity within the GAC-FBR.

  9. Physicochemical properties influencing denitrification rate and microbial activity in denitrification bioreactors

    NASA Astrophysics Data System (ADS)

    Schmidt, C. A.

    2012-12-01

    The use of N-based fertilizer will need to increase to meet future demands, yet existing applications have been implicated as the main source of coastal eutrophication and hypoxic zones. Producing sufficient crops to feed a growing planet will require efficient production in combination with sustainable treatment solutions. The long-term success of denitrification bioreactors to effectively remove nitrate (NO¬3), indicates this technology is a feasible treatment option. Assessing and quantifying the media properties that affect NO¬3 removal rate and microbial activity can improve predictions on bioreactor performance. It was hypothesized that denitrification rates and microbial biomass would be correlated with total C, NO¬3 concentration, metrics of organic matter quality, media surface area and laboratory measures of potential denitrification rate. NO¬3 removal rates and microbial biomass were evaluated in mesocosms filled with different wood treatments and the unique influence of these predictor variables was determined using a multiple linear regression analysis. NO3 reduction rates were independent of NO¬3 concentration indicating zero order reaction kinetics. Temperature was strongly correlated with denitrification rate (r2=0.87; Q10=4.7), indicating the variability of bioreactor performance in differing climates. Fiber quality, and media surface area were strong (R>0.50), unique predictors of rates and microbial biomass, although C:N ratio and potential denitrification rate did not predict actual denitrification rate or microbial biomass. Utilizing a stepwise multiple linear regression, indicates that the denitrification rate can be effectively (r2=0.56;p<0.0001) predicted if the groundwater temperature, neutral detergent fiber and surface area alone are quantified. These results will assist with the widespread implementation of denitrification bioreactors to achieve significant N load reductions in large watersheds. The nitrate reduction rate as a

  10. Enhanced dewaterability of waste activated sludge by Fe(II)-activated peroxymonosulfate oxidation.

    PubMed

    Liu, Jun; Yang, Qi; Wang, Dongbo; Li, Xiaoming; Zhong, Yu; Li, Xin; Deng, Yongchao; Wang, Liqun; Yi, Kaixin; Zeng, Guangming

    2016-04-01

    The effect of Fe(II)-activated peroxymonosulfate (Fe(II)-PMS) oxidation on the waste activated sludge (WAS) dewatering and its mechanisms were investigated in this study. The capillary suction time (CST), specific resistance to filterability (SRF) of sludge and water content (WC) of dewatered sludge cake were chosen as the main parameters to evaluate the sludge dewaterability. Experimental results showed that Fe(II)-PMS effectively disintegrated sludge and improved sludge dewaterability. High CST and SRF reduction (90% and 97%) was achieved at the optimal conditions of PMS (HSO5(-)) 0.9mmol/gVSS, Fe(II) 0.81mmol/gVSS, and pH 6.8. Extracellular polymeric substances (EPS) and three-dimensional excitation-emission matrix (3D-EEM) fluorescence spectroscopy before and after Fe(II)-PMS oxidation were determined to explain the enhanced dewatering mechanism. The release of EPS-bound water induced by the destruction of EPS was the primary reason for the improvement of sludge dewaterability during Fe(II)-PMS oxidation. PMID:26851897

  11. Toluene biodegradation in a solid/liquid system involving immobilized activated sludge and silicone oil as pollutant reservoir.

    PubMed

    Diz Castro, Manuel; Gómez-Díaz, Diego; Amrane, Abdeltif; Couvert, Annabelle

    2015-01-01

    A solid/liquid system involving activated sludge immobilized in an agar medium and a non-aqueous phase liquid containing the target pollutant has been considered to treat a model hydrophobic volatile organic compound, toluene. The positive impact of the use of a multiphase bioreactor is that the organic phase constitutes a pollutant reservoir and also helps to overcome possible pollutant toxicity. In addition and to overcome the drawbacks of the use of a solid organic phase (high pressure drop and low mass transfer) instead of a liquid organic phase, the considered solid phase was the aqueous. Consequently, silicone oil (polydimethylsiloxane) which showed its relevance for implementation in multiphase bioreactors was used. Promising results were observed from the analysis of toluene in the gaseous phase; for an initial amount of 2 g L(-1) related to the organic phase, a v/v ratio of 0.5 of the organic phase to the aqueous agar phase, total toluene consumption was observed in about 9 days, leading to a global biodegradation rate of approximately 3.1 mg L(-1) h(-1), namely in the range of values previously observed in liquid/liquid systems. PMID:25187471

  12. rRNA Gene Expression of Abundant and Rare Activated-Sludge Microorganisms and Growth Rate Induced Micropollutant Removal.

    PubMed

    Vuono, David C; Regnery, Julia; Li, Dong; Jones, Zackary L; Holloway, Ryan W; Drewes, Jörg E

    2016-06-21

    The role of abundant and rare taxa in modulating the performance of wastewater-treatment systems is a critical component of making better predictions for enhanced functions such as micropollutant biotransformation. In this study, we compared 16S rRNA genes (rDNA) and rRNA gene expression of taxa in an activated-sludge-treatment plant (sequencing batch membrane bioreactor) at two solids retention times (SRTs): 20 and 5 days. These two SRTs were used to influence the rates of micropollutant biotransformation and nutrient removal. Our results show that rare taxa (<1%) have disproportionally high ratios of rRNA to rDNA, an indication of higher protein synthesis, compared to abundant taxa (≥1%) and suggests that rare taxa likely play an unrecognized role in bioreactor performance. There were also significant differences in community-wide rRNA expression signatures at 20-day SRT: anaerobic-oxic-anoxic periods were the primary driver of rRNA similarity. These results indicate differential expression of rRNA at high SRTs, which may further explain why high SRTs promote higher rates of micropollutant biotransformation. An analysis of micropollutant-associated degradation genes via metagenomics and direct measurements of a suite of micropollutants and nutrients further corroborates the loss of enhanced functions at 5-day SRT operation. This work advances our knowledge of the underlying ecosystem properties and dynamics of abundant and rare organisms associated with enhanced functions in engineered systems. PMID:27196630

  13. Biohydrogen production in a three-phase fluidized bed bioreactor using sewage sludge immobilized by ethylene-vinyl acetate copolymer.

    PubMed

    Lin, Chi-Neng; Wu, Shu-Yii; Chang, Jian-Sheng; Chang, Jo-Shu

    2009-07-01

    Ethylene-vinyl acetate (EVA) copolymer was used to immobilize H(2)-producing sewage sludge for H(2) production in a three-phase fluidized bed reactor (FBR). The FBR with an immobilized cell packing ratio of 10% (v/v) and a liquid recycle rate of 5l/min (23% bed expansion) was optimal for dark H(2) fermentation. The performance of the FBR reactor fed with sucrose-based synthetic medium was examined under various sucrose concentration (C(so)) and hydraulic retention time (HRT). The best volumetric H(2) production rate of 1.80+/-0.02 H(2) l/h/l occurred at C(so)=40 g COD/l and 2h HRT, while the optimal H(2) yield (4.26+/-0.04 mol H(2)/mol sucrose) was obtained at C(so)=20 g COD/l and 6h HRT. The H(2) content in the biogas was stably maintained at 40% or above. The primary soluble metabolites were butyric acid and acetic acid, as both products together accounted for 74-83% of total soluble microbial products formed during dark H(2) fermentation. PMID:19318247

  14. Effect of recycling thermophilic sludge on the activated-sludge process. Report for October 1984-June 1989

    SciTech Connect

    Prakasam, T.B.S.; Soszynski, S.; Zenz, D.R.; Lue-Hing, C.; Blyth, L.

    1990-01-01

    A full-scale investigation was undertaken at Chicago's Hanover Park Water Reclamation Plant (WRP) to study whether the net sludge production from the WRP could be reduced by implementing a scheme developed by W. Torpey et al. (1984). In this process, sludge is withdrawn from a thermophilic digester operated in series with a mesophilic digester and partially recycled into the aeration tanks of the activated sludge system. The Hanover Park WRP, which has a design flow capacity of 45,420 million cu m per day (12 mgd), was split into a control section and an experimental section. The two sections were operated similarly except the thermophilic drawoff was recycled into the aeration tanks of the experimental section from a digester system consisting of mesophilic and thermophilic digesters operated in series. A reduction in net sludge production of about 10 percent was achieved at 40 percent recycle of thermophilic sludge into the aeration tanks at the Hanover Park WRP. This was a much smaller reduction than obtained by Torpey et al. Sludge dewatering properties were not improved. The recycling produced no adverse effects on quality of the treated wastewater.

  15. The presence and role of bacterial quorum sensing in activated sludge

    PubMed Central

    Chong, Grace; Kimyon, Onder; Rice, Scott A.; Kjelleberg, Staffan; Manefield, Mike

    2012-01-01

    Summary Activated sludge used for wastewater treatment globally is composed of a high‐density microbial community of great biotechnological significance. In this study the presence and purpose of quorum sensing via N‐acylated‐l‐homoserine lactones (AHLs) in activated sludge was explored. The presence of N‐heptanoyl‐l‐homoserine lactone in organic extracts of sludge was demonstrated along with activation of a LuxR‐based AHL monitor strain deployed in sludge, indicating AHL‐mediated gene expression is active in sludge flocculates but not in the bulk aqueous phase. Bacterial isolates from activated sludge were screened for AHL production and expression of phenotypes commonly but not exclusively regulated by AHL‐mediated gene transcription. N‐acylated‐l‐homoserine lactone and exoenzyme production were frequently observed among the isolates. N‐acylated‐l‐homoserine lactone addition to sludge upregulated chitinase activity and an AHL‐ and chitinase‐producing isolate closely related to Aeromonas hydrophila was shown to respond to AHL addition with upregulation of chitinase activity. N‐acylated‐l‐homoserine lactones produced by this strain were identified and genes ahyI/R and chiA, encoding AHL production and response and chitinase activity respectively, were sequenced. These experiments provide insight into the relationship between AHL‐mediated gene expression and exoenzyme activity in activated sludge and may ultimately create opportunities to improve sludge performance. PMID:22583685

  16. [Synergistic effects of nano-sized magnetic particles and uncoupler to the characteristics of activated sludge].

    PubMed

    Gao, Li-ying; Tang, Bing; Liang, Ling-yan; Huang, Shao-song; Fu, Feng-lian; Luo, Jian-zhong

    2012-08-01

    For improving the performance and sludge settling property of an activated sludge reduction process with uncoupler, in this investigation, uncoupler and nano-sized magnetic particles were added simultaneously to a sequencing batch reactor for exploring their synergistic effects to the characteristics of activated sludge. The results showed that the volume reduction of sludge reached 41% with single 2,4,5-Trichlorophenol (TCP) Comparing with the control experiment, the biodegradability and settling properties of the activated sludge decreased. Under the actions of TCP combined with nano-sized magnetic particles, the volume reduction of sludge reached 34%, the removal efficiencies of COD, nitrogen, and phosphorus as well as the sludge settling property were not significantly influenced. After 31 d's operation, the dehydrogenase activity was improved by 10%-18% and exhibited an accumulative effect over time. It was observed with an optical microscope that the species and amounts of protozoon and metazoan increased and a compact structure of sludge floc was formed. The results also indicated that using nano-sized magnetic particles and uncoupler could restrict the yield of excess sludge and improve the performance of an activated sludge system. PMID:23213903

  17. Variations of respiratory activity and glutathione in activated sludges exposed to low ozone doses.

    PubMed

    Dziurla, M A; Salhi, M; Leroy, P; Paul, E; Ginestet, Ph; Block, J C

    2005-07-01

    Ozonation is one of the most effective treatments for reducing the production of activated sludges in wastewater treatment plants. However, because microorganisms are present in the form of microcolonies, some bacteria may be exposed to sub-lethal ozone doses that could lead to adaptation and resistance to further exposition to oxidative treatment. This represents a major question as it may limit the effect of the treatment, especially when low ozone doses are applied. The critical ozone dosage, defined as the lowest specific transferred ozone concentration leading to a decrease in the maximum oxygen uptake rate was estimated to range between 0.9 and 13.6mg O(3)g(-1) COD(sludges), according to the sludges tested. The lowest ozone dosage leading to the decrease of GSH and GSHt concentrations could be estimated to be lower than 10mg O(3)g(-1) COD(sludges) for GSH, and close to 10mg O(3)g(-1) COD(sludges) for GSHt. After sludge exposure to low ozone doses, no higher amounts of glutathione were synthesized, suggesting that no development of resistance to ozonation occurred after sludge treatment with low ozone doses. PMID:15972223

  18. Evaluation of anaerobic digestion processes for short sludge-age waste activated sludge combined with anammox treatment of digestate liquor.

    PubMed

    Ge, Huoqing; Batstone, Damien; Keller, Jurg

    2016-01-01

    The need to reduce energy input and enhance energy recovery from wastewater is driving renewed interest in high-rate activated sludge treatment (i.e. short hydraulic and solids retention times (HRT and SRT, respectively)). This process generates short SRT activated sludge stream, which should be highly degradable. However, the evaluation of anaerobic digestion of short SRT sludge has been limited. This paper assesses anaerobic digestion of short SRT sludge digestion derived from meat processing wastewater under thermophilic and mesophilic conditions. The thermophilic digestion system (55°C) achieved 60 and 68% volatile solids destruction at 8 day and 10 day HRT, respectively, compared with 50% in the mesophilic digestion system (35°C, 10 day HRT). The digestion effluents from the thermophilic (8-10 day HRT) and mesophilic systems were stable, as assessed by residual methane potentials. The ammonia rich sludge dewatering liquor was effectively treated by a batch anammox process, which exhibited comparable nitrogen removal rate as the tests using a control synthetic ammonia solution, indicating that the dewatering liquor did not have inhibiting/toxic effects on the anammox activity. PMID:26942526

  19. Pharmaceutically active compounds in sludge stabilization treatments: anaerobic and aerobic digestion, wastewater stabilization ponds and composting.

    PubMed

    Martín, Julia; Santos, Juan Luis; Aparicio, Irene; Alonso, Esteban

    2015-01-15

    Sewage sludge disposal onto lands has been stabilized previously but still many pollutants are not efficiently removed. Special interest has been focused on pharmaceutical compounds due to their potential ecotoxicological effects. Nowadays, there is scarce information about their occurrence in different sludge stabilization treatments. In this work, the occurrence of twenty-two pharmaceutically active compounds has been studied in sludge from four sludge stabilization treatments: anaerobic digestion, aerobic digestion, composting and lagooning. The types of sludge evaluated were primary, secondary, anaerobically-digested and dehydrated, composted, mixed, aerobically-digested and dehydrated and lagoon sludge. Nineteen of the twenty-two pharmaceutically active compounds monitored were detected in sewage sludge. The most contaminated samples were primary sludge, secondary sludge and mixed sludge (the average concentrations of studied compounds in these sludges were 179, 310 and 142 μg/kg dm, respectively) while the mean concentrations found in the other types of sewage sludge were 70 μg/kg dm (aerobically-digested sludge), 63 μg/kg dm (lagoon sludge), 12 μg/kg dm (composted sludge) and 8 μg/kg dm (anaerobically-digested sludge). The antibiotics ciprofloxacin and norfloxacin were found at the highest concentration levels in most of the analyzed sludge samples (up to 2660 and 4328 μg/kg dm, respectively). Anaerobic-digestion treatment reduced more considerably the concentration of most of the studied compounds than aerobic-digestion (especially in the case of bezafibrate and fluoroquinolones) and more than anaerobic stabilization ponds (in the case of acetaminophen, atenolol, bezafibrate, carbamazepine, 17α-ethinylestradiol, naproxen and salicylic acid). Ecotoxicological risk assessment, of sludge application onto soils, has also been evaluated. Risk quotients, expressed as the ratio between the predicted environmental concentration and the predicted non

  20. EFFECT OF RECYCLING THERMOPHILICALLY DIGESTED SLUDGE ON THE ACTIVATED SLUDGE PROCESS

    EPA Science Inventory

    A full-scale investigation was undertaken at Chicago's Hanover Park Water Reclamation Plant (WRP) to study whether the net sludge production from the WRP could be reduced by implementing a scheme developed by W. Torpey et al. (1984). n this process, sludge is withdrawn from a the...

  1. Diversity and dynamics of Archaea in an activated sludge wastewater treatment plant

    PubMed Central

    2012-01-01

    Background The activated sludge process is one of the most widely used methods for treatment of wastewater and the microbial community composition in the sludge is important for the process operation. While the bacterial communities have been characterized in various activated sludge systems little is known about archaeal communities in activated sludge. The diversity and dynamics of the Archaea community in a full-scale activated sludge wastewater treatment plant were investigated by fluorescence in situ hybridization, terminal restriction fragment length polymorphism analysis and cloning and sequencing of 16S rRNA genes. Results The Archaea community was dominated by Methanosaeta-like species. During a 15 month period major changes in the community composition were only observed twice despite seasonal variations in environmental and operating conditions. Water temperature appeared to be the process parameter that affected the community composition the most. Several terminal restriction fragments also showed strong correlations with sludge properties and effluent water properties. The Archaea were estimated to make up 1.6% of total cell numbers in the activated sludge and were present both as single cells and colonies of varying sizes. Conclusions The results presented here show that Archaea can constitute a constant and integral part of the activated sludge and that it can therefore be useful to include Archaea in future studies of microbial communities in activated sludge. PMID:22784022

  2. Energy conservation and production in a packed-bed anaerobic bioreactor

    SciTech Connect

    Pit, W.W. Jr.; Genung, R.K.

    1980-01-01

    Oak Ridge National Laboratory (ORNL) is developing an energy-conserving/ producing wastewater treatment system based on a fixed-film anaerobic bioreactor. The treatment process is based on passing wastewaters upward through the bioreactor for continuous treatment by gravitational settling, biophysical filtration and biological decomposition. A two-year pilot-plant project using a bioreactor designed to treat 5000 gpd has been conducted using raw wastewater on a municipal site in Oak Ridge, Tennessee. Data obtained for the performance of the bioreactor during this project have been analyzed by ORNL and Associated Water and Air Resources Engineers (AWARE), Inc. of Nashville, Tennessee. From these analyses it was estimated that hydraulic loading rates of 0.25 gpm/ft/sup 2/ and hydraulic residence times of 10 hours could be used in designing such bioreactors for the secondary treatment of municipal wastewaters. Conceptual designs for total treatment systems processing up to one million gallons of wastewater per day were developed based on the performance of the pilot plant bioreactor. These systems were compared to activated sludge treatment systems also operating under secondary treatment requirements and were found to consume as little as 30% of the energy required by the activated sludge systems. Economic advantages of the process result from the elimination of operating energy requirements associated with the aeration of aerobic-based processes and with the significant decrease of sludge-handling costs required with conventional activated sludge treatment systems.Furthermore, methane produced by anaerobic fermentation processes occurring during the biological decomposition of carbonaceous wastes also represented a significant and recoverable energy production. For dilute municipal wastewaters this would completely offset the remaining energy required for treatment, while for concentrated industrial wastewater would result in a net production of energy.

  3. Physicochemical changes effected in activated sludge by the earthworm Eisenia foetida. [Concentration of heavy metals during sludge catabolism

    SciTech Connect

    Hartenstein, R.; Hartenstein, F.

    1981-09-01

    Measurements were made of some physicochemical changes effected in activated sludge by the earthworm Eisenia foetida following conversion of the sludge into wormcasts. Mineralization was accelerated 1.3-fold and 2% of the minerals were assimilated. The rate at which heavy metals were concentrated during sludge catabolism was also accelerated. Castings stabilized within 2 weeks, as indexed by respirometry. Nucleic acids, which can be used as an index of microbial biomass, were present at a greater concentration in the wormcasts than in the sludge, while the phenolic content, which may potentially serve as an index of humification, was less concentrated. Other changes included a reduction in pH and an increase in oxidation-reduction potential and cation exchange capacity. The major general effect of E. foetida on the physicochemical properties of activated sludge is to convert a material which has a relatively small surface/volume ratio into numerous particles with an overall large S/V ratio, thus accelerating decomposition, mineralization, drying, and preclusion of malodor.

  4. Gamma irradiation induced disintegration of waste activated sludge for biological hydrogen production

    NASA Astrophysics Data System (ADS)

    Yin, Yanan; Wang, Jianlong

    2016-04-01

    In this paper, gamma irradiation was applied for the disintegration and dissolution of waste activated sludge produced during the biological wastewater treatment, and the solubilized sludge was used as substrate for bio-hydrogen production. The experimental results showed that the solubilization of waste activated sludge was 53.7% at 20 kGy and pH=12, and the SCOD, polysaccharides, protein, TN and TP contents in the irradiated sludge solutions was 3789.6 mg/L, 268.3 mg/L, 1881.5 mg/L, 132.3 mg/L and 80.4 mg/L, respectively. The irradiated sludge was used for fermentative hydrogen production, and the hydrogen yield was 10.5±0.7 mL/g SCODconsumed. It can be concluded that the irradiated waste activated sludge could be used as a low-cost substrate for fermentative hydrogen production.

  5. Bioaugmentation to improve nitrification in activated sludge treatment.

    PubMed

    Leu, Shao-Yuan; Stenstrom, Michael K

    2010-06-01

    Bioaugmentation is a proposed technique to improve nutrient removal in municipal wastewater treatment. Compared with commonly used nitrification/denitrification (NDN) processes, bioaugmentation may be able to reduce tankage or land requirements. Many approaches for bioaugmentation have been developed, but few studies have compared the benefits among different approaches. This paper quantifies the effectiveness of bioaugmentation processes and investigates three major "onsite" bioaugmentation alternatives: 1) the parallel-plants approach, which uses acclimated biomass grown in a nitrifying "long-SRT" (sludge retention time) plant to augment a low-SRT treatment plant; 2) the enricher-reactor approach, which uses an offline reactor to produce the augmentation cultures; and 3) the enricher-reactor/return activated sludge (ER-RAS) approach, which grows enrichment culture in a reaeration reactor that receives a portion of the recycle activated sludge. Kinetic models were developed to simulate each approach, and the benefits of various approaches are presented on the same basis with controllable parameters, such as bioaugmentation levels, aeration tank volume, and temperatures. Examples were given to illustrate the potential benefits of bioaugmentation by upgrading a "carbon-only" wastewater treatment plant to nitrification. Simulation results suggested that all bioaugmentation approaches can decrease the minimum SRT for nitrification. The parallel-plants approach creates the highest concentration of biomass but may fail at too low temperature. The ER-RAS approach likely would be more useful at lower temperature and required less reactor volume; enricher-reactor approach would likely be more advantageous in the presence of inhibitory compound(s). PMID:20572460

  6. [Influence of the Application of Activated Persulfate on Municipal Sludge Conditioning].

    PubMed

    Xu, Xin; Pu, Wen-hong; Shi, Ya-fei; Yu, Wen-bo; Zhang, Shi-nan; Song, Jian; Zhang, Hao; He, Shu; Yang, Chang-zhu; Yang, Jia-kuan

    2015-11-01

    The water content of dewatered sewage sludge can decrease at about 80% by traditional sludge dewatering technologies. High water content has negative impacts on the sequent sludge disposal with a stricter standard. The sulfate free radical SO4(*-), generated by activated persulfate, is a powerful oxidant. This article found that it could improve sludge dewatering properties by using the Fe2+ activated sodium persulfate (SPS). The results showed that when using Fe2+ 25.88 mg x g(-1) (based on dry sludge solid) and S2 O8(2-) 80 mg x g(-1) (the mole ratio of Fe2+ to S2 O8(2-) was 1.1 : 1) for sludge conditioning, it could reduce the capillary suction time (CST) and specific resistance to filtration (RSF) of sludge, increased the protein and ploysaccharide as well as the COD concentration in the filtrate. The further research showed that this method could change the zeta potential of sludge, increased the sludge particle specific surface area, and made flocs become a loose layered structure from dense clusters, which was beneficial to improve the sludge dewaterability. PMID:26911010

  7. Purification of total DNA extracted from activated sludge.

    PubMed

    Shan, Guobin; Jin, Wenbiao; Lam, Edward K H; Xing, Xinhui

    2008-01-01

    Purification of the total DNA extracted from activated sludge samples was studied. The effects of extraction buffers and lysis treatments (lysozyme, sodium dodecyl sulfate (SDS), sonication, mechanical mill and thermal shock) on yield and purity of the total DNA extracted from activated sludge were investigated. It was found that SDS and mechanical mill were the most effective ways for cell lysis, and both gave the highest DNA yields, while by SDS and thermal shock, the purest DNA extract could be obtained. The combination of SDS with other lysis treatment, such as sonication and thermal shock, could apparently increase the DNA yields but also result in severe shearing. For the purification of the crude DNA extract, polyvinyl polypyrrolidone was used for the removal of humic contaminants. Cetyltrimethyl ammonium bromide, potassium acetate and phenol/chloroform were used to remove proteins and polysaccharides from crude DNA. Crude DNA was further purified by isopropanol precipitation. Thus, a suitable protocol was proposed for DNA extraction, yielding about 49.9 mg (total DNA)/g volatile suspended solids, and the DNA extracts were successfully used in PCR amplifications for 16S rDNA and 16S rDNA V3 region. The PCR products of 16S rDNA V3 region allowed the DGGE analysis (denatured gradient gel electrophoresis) to be possible. PMID:18572527

  8. Grazing by protozoa as selection factor for activated sludge bacteria.

    PubMed

    Güde, H

    1979-09-01

    In continuous culture enrichments that were inoculated with activated sludge and were fed with polymeric substrates, freely dispersed single-celled bacteria belonging to theCytophaga group dominated among the initial populations, irrespective of the activated sludge source. These populations were grazed by flagellated protozoa which after several days reached high cell densities. Other morphologic bacterial groups such as spiral-shaped or filamentous bacteria then became dominant. In defined mixed culture experiments with bacterial isolates from the enrichment cultures, it was shown that a "grazing-resistant"Microcyclus strain outgrew aCytophaga strain in the presence of grazing protozoa. In contrast, theCytophaga strain competed successfully with theMicrocyclus strain and with other "grazing-resistant" strains under protozoa-free conditions. Furthermore, it was demonstrated that assumed grazing resistance factors such as floccing or filamentous growth were lost by some of the strains when they were grown for several generations in continuous culture under the same conditions, but in the absence of protozoa. PMID:24232496

  9. Pyrolysis of activated sludge: energy analysis and its technical feasibility.

    PubMed

    Agarwal, Manu; Tardio, James; Venkata Mohan, S

    2015-02-01

    A comprehensive study on the potential of pyrolysis of activated sludge to generate substances that can be used to produce energy was evaluated for its technical and environmental viability. The products of the process viz., pyrolysis gas, pyrolysis oil and char can readily be used by the major energy consumers viz., electricity and transportation. Based on the results obtained it is estimated that a 1 ton capacity process for pyrolysis of activated sludge can serve the electrical needs of a maximum of 239, 95 and 47 Indian houses per day, considering lower middle class, middle class and upper middle class, respectively. In addition the process would also produce the daily methane (CNG) requirement of 128 public transport buses. The process was determined to be technically feasible at low and medium temperatures for both, pyrolysis gas and electrical energy. The gas generated could be utilized as fuel directly while the oil generated would require pretreatment before its potential application. The process is potentially sustainable when commercialized and can self-sustain in continuous mode of operation in biorefinery context. PMID:25451771

  10. Effects of waste activated sludge and surfactant addition on primary sludge hydrolysis and short-chain fatty acids accumulation.

    PubMed

    Ji, Zhouying; Chen, Guanlan; Chen, Yinguang

    2010-05-01

    This paper focused on the effects of waste activated sludge (WAS) and surfactant sodium dodecylbenzene sulfonate (SDBS) addition on primary sludge (PS) hydrolysis and short-chain fatty acids (SCFA) accumulation in fermentation. The results showed that sludge hydrolysis, SCFA accumulation, NH(4)(+)-N and PO(4)(3-)-P release, and volatile suspended solids (VSS) reduction were increased by WAS addition to PS, which were further increased by the addition of SDBS to the mixture of PS and WAS. Acetic, propionic and valeric acids were the top three SCFA in all experiments. Also, the fermentation liquids of PS, PS+WAS, and PS+WAS+SDBS were added, respectively, to municipal wastewater to examine their effects on biological municipal wastewater treatment, and the enhancement of both wastewater nitrogen and phosphorus removals was observed compared with no fermentation liquid addition. PMID:20096564

  11. Effect of low temperature on highly unsaturated fatty acid biosynthesis in activated sludge.

    PubMed

    He, Su; Ding, Li-Li; Xu, Ke; Geng, Jin-Ju; Ren, Hong-Qiang

    2016-07-01

    Low temperature is a limiting factor for the microbial activity of activated sludge for sewage treatment plant in winter. Highly unsaturated fatty acid (UFA) biosynthesis, phospholipid fatty acid (PLFA) constituents and microbial structure in activated sludge at low temperature were investigated. Over 12 gigabases of metagenomic sequence data were generated with the Illumina HiSeq 2000 platform. The result showed 43.11% of phospholipid fatty acid (PLFA) in the activated sludge participated in UFA biosynthesis, and γ-Linolenic could be converted to Arachidonic acid at low temperature. The highly UFA biosynthesis in activated sludge was n-6 highly UFA biosynthesis, rather than n-3 highly UFA biosynthesis. The microbial community structures of activated sludge were analyzed by PLFA and high-throughput sequencing (HiSeq) simultaneously. Acidovorax, Pseudomonas, Flavobacterium and Polaromonas occupied higher percentage at 5°C, and genetic changes of highly UFA biosynthesis derived from microbial community structures change. PMID:27035483

  12. Toxic influence of silver and uranium salts on activated sludge of wastewater treatment plants and synthetic activated sludge associates modeled on its pure cultures.

    PubMed

    Tyupa, Dmitry V; Kalenov, Sergei V; Skladnev, Dmitry A; Khokhlachev, Nikolay S; Baurina, Marina M; Kuznetsov, Alexander Ye

    2015-01-01

    Toxic impact of silver and uranium salts on activated sludge of wastewater treatment facilities has been studied. Some dominating cultures (an active nitrogen fixer Agrobacterium tumifaciens (A.t) and micromyces such as Fusarium nivale, Fusarium oxysporum, and Penicillium glabrum) have been isolated and identified as a result of selection of the activated sludge microorganisms being steadiest under stressful conditions. For these cultures, the lethal doses of silver amounted 1, 600, 50, and 300 µg/l and the lethal doses of uranium were 120, 1,500, 1,000, and 1,000 mg/l, respectively. A.tumifaciens is shown to be more sensitive to heavy metals than micromyces. Synthetic granular activated sludge was formed on the basis of three cultures of the isolated micromyces steadiest against stress. Its granules were much more resistant to silver than the whole native activated sludge was. The concentration of silver causing 50 % inhibition of synthetic granular activated sludge growth reached 160-170 μg/l as far as for the native activated sludge it came only to 100-110 μg/l. PMID:25027236

  13. An ecosystem analysis of the activated sludge microbial community.

    PubMed

    Yiannakopoulou, Trissevyene V

    2010-01-01

    This study was undertaken (i) to investigate the interactions of the activated sludge microbial community in a chemostat with the "environment", such as the substrate composition and variations, (ii) to investigate how these interactions affect the quality of the treated effluent and (iii) to determine the limits or applicability conditions to the indicators and to the prediction potential of the treated effluent quality. This work presents (a) the experimental results obtained from a reactor fed municipal wastewater (Data Set2-DS2) concerning the reactor's operating conditions and the microbial community of the sludge (b) comparisons between DS2 and an older Data Set (DS1) obtained when the reactor was fed synthetic substrate, all other experimental conditions being identical, and (c) simulation results and sensitivity analyses of two model runs (R1 and R2, corresponding to DS1 and DS2). The first trophic level (P(1)) of the DS2 microbial community consisted of bacteria, the second trophic level (P(2)) of bacteria-eating protozoa, rotifers and nematodes and the third trophic level (P(3)) of carnivorous protozoa and arthropods. Rotifers were an important constituent of the DS2 microbial community. The DS1 and DS1 communities differed in total size, trophic level sizes and species composition. Correlations between the major microbial groups of DS2 community and either loading rates or effluent quality attributes were generally low, but the correlation of bacteria with SVI and ammonia in the effluent was better. Also, the ratio of rotifers to protozoa in P(2) was correlated to BOD in the effluent. The results of this work indicate that predictions of the treated effluent quality based only on protozoa may not be safe. Sensitivity analysis of R2 run indicate that, when variation in Y and K(d) biokinetic coefficients of the sludge are combined with fluctuations in composition and quality of municipal wastewater entering the reactor, then sufficient significant

  14. Nitrification in brackish water recirculating aquaculture system integrated with activated packed bed bioreactor.

    PubMed

    Rejish Kumar, V J; Joseph, Valsamma; Philip, Rosamma; Bright Singh, I S

    2010-01-01

    Recirculation aquaculture systems (RAS) depend on nitrifying biofilters for the maintenance of water quality, increased biosecurity and environmental sustainability. To satisfy these requirements a packed bed bioreactor (PBBR) activated with indigenous nitrifying bacterial consortia has been developed and commercialized for operation under different salinities for instant nitrification in shrimp and prawn hatchery systems. In the present study the nitrification efficiency of the bioreactor was tested in a laboratory level recirculating aquaculture system for the rearing of Penaeus monodon for a period of two months under higher feeding rates and no water exchange. Rapid setting up of nitrification was observed during the operation, as the volumetric total ammonia nitrogen removal rates (VTR) increased with total ammonia nitrogen (TAN) production in the system. The average Volumetric TAN Removal Rates (VTR) at the feeding rate of 160 g/day from 54-60th days of culture was 0.1533+/-0.0045 kg TAN/m(3)/day. The regression between VTR and TAN explained 86% variability in VTR (P<0.001). The laboratory level RAS demonstrated here showed high performance both in terms of shrimp biomass yield and nitrification and environmental quality maintenance. Fluorescent in-situ Hybridization analysis of the reactor biofilm ensured the presence of autotrophic nitrifier groups such as Nitrosococcus mobilis lineage, Nitrobacter spp and phylum Nitrospira, the constituent members present in the original consortia used for activating the reactors. This showed the stability of the consortia on long term operation. PMID:20150717

  15. Effect of petrochemical sludge concentrations of changes in mutagenic activity during soil bioremediation process.

    PubMed

    Morelli, I S; Vecchioli, G I; Del Panno, M T; Painceira, M T

    2001-10-01

    The present study was performed to assess the effect of the petrochemical sludge application rate on the mutagenic activity (Ames test) of soil and the persistence of mutagenic activity during laboratory soil bioremediation process. Sludge-soil systems were prepared at four different sludge application rates (1.25, 2.5, 5, and 10% w/w). Unamended soil was used as a control. Immediately following sludge application, in the absence or presence of S9, a linear correlation between sludge application rates and mutagenicity was found but differed significantly (p < 0.05) from the control system only at higher application rates (5 and 10% w/w). The direct mutagenicity of all systems decreases during the bioremediation process, and after a year of treatment only the 10% system induced a mutagenic response that was significantly different from the control system. On the other hand, an initial increase of the indirect mutagenicity was observed at all application rates. The time required for observing this increase was inversely proportional to the initial sludge concentration. After a year of treatment, the indirect mutagenicity of all sludge-amended soils was not significantly different but was significantly different from the unamended soils. The persistence of the direct mutagenic activity of the sludge-amended soils was related to the sludge concentration, whereas the indirect mutagenic persistence was related to the relationship between easily degradable hydrocarbons and polynuclear aromatic hydrocarbons concentration and independent from the initial application rate. PMID:11596747

  16. Thermal hydrolysis of waste activated sludge at Hengelo Wastewater Treatment Plant, the Netherlands.

    PubMed

    Oosterhuis, Mathijs; Ringoot, Davy; Hendriks, Alexander; Roeleveld, Paul

    2014-01-01

    The thermal hydrolysis process (THP) is a sludge treatment technique which affects anaerobic biodegradability, viscosity and dewaterability of waste activated sludge (WAS). In 2011 a THP-pilot plant was operated, connected to laboratory-scale digesters, at the water board Regge en Dinkel and in cooperation with Cambi A.S. and MWH Global. Thermal hydrolysis of WAS resulted in a 62% greater volatile solids (VS) reduction compared to non-hydrolysed sludge. Furthermore, the pilot digesters could be operated at a 2.3 times higher solids loading rate compared to conventional sludge digesters. By application of thermal sludge hydrolysis, the overall efficiency of the sludge treatment process can be improved. PMID:25026572

  17. Activity, life time and effect of hydrolytic enzymes for enhanced biogas production from sludge anaerobic digestion.

    PubMed

    Odnell, Anna; Recktenwald, Michael; Stensén, Katarina; Jonsson, Bengt-Harald; Karlsson, Martin

    2016-10-15

    As an alternative to energy intensive physical methods, enzymatic treatment of sludge produced at wastewater treatment plants for increased hydrolysis and biogas production was investigated. Several hydrolytic enzymes were assessed with a focus on how enzyme activity and life time was influenced by sludge environments. It could be concluded that the activity life time of added enzymes was limited (<24 h) in both waste activated sludge and anaerobic digester sludge environments and that this was, for the majority of enzymes, due to endogenous protease activity. In biogas in situ experiments, subtilisin at a 1% mixture on basis of volatile solids, was the only enzyme providing a significantly increased biomethane production of 37%. However, even at this high concentration, subtilisin could not hydrolyze all available substrate within the life time of the enzyme. Thus, for large scale implementation, enzymes better suited to the sludge environments are needed. PMID:27498254

  18. Effects of Metal Nanoparticles on Methane Production from Waste-Activated Sludge and Microorganism Community Shift in Anaerobic Granular Sludge.

    PubMed

    Wang, Tao; Zhang, Dong; Dai, Lingling; Chen, Yinguang; Dai, Xiaohu

    2016-01-01

    Extensive use of nanoparticles (NPs) in consumer and industrial products has led to concerns about their potential environmental impacts; however, the influences of different NPs (e.g., nZVI (nano zero-valent iron), Ag NPs, Fe2O3 NPs and MgO NPs) on the anaerobic digestion of sludge have not yet been studied in depth. Additionally, a new guideline or the use of different NPs in the anaerobic digestion of sludge should be established to improve the anaerobic digestion of sludge and avoid inhibitory effects. This study investigated the effects of four representative NPs (i.e., nZVI, Ag NPs, Fe2O3 NPs and MgO NPs) on methane production during the anaerobic digestion of waste activated sludge (WAS). The presence of 10 mg/g total suspended solids (TSS) nZVI and 100 mg/g TSS Fe2O3 NPs increased methane production to 120% and 117% of the control, respectively, whereas 500 mg/g TSS Ag NPs and 500 mg/g TSS MgO NPs generated lower levels of methane production (73.52% and 1.08% that of the control, respectively). These results showed that low concentrations of nZVI and Fe2O3 NPs promoted the amount of microbes (Bacteria and Archaea) and activities of key enzymes but that higher concentrations of Ag NPs and MgO NPs inhibited them. PMID:27166174

  19. Effects of Metal Nanoparticles on Methane Production from Waste-Activated Sludge and Microorganism Community Shift in Anaerobic Granular Sludge

    NASA Astrophysics Data System (ADS)

    Wang, Tao; Zhang, Dong; Dai, Lingling; Chen, Yinguang; Dai, Xiaohu

    2016-05-01

    Extensive use of nanoparticles (NPs) in consumer and industrial products has led to concerns about their potential environmental impacts; however, the influences of different NPs (e.g., nZVI (nano zero-valent iron), Ag NPs, Fe2O3 NPs and MgO NPs) on the anaerobic digestion of sludge have not yet been studied in depth. Additionally, a new guideline or the use of different NPs in the anaerobic digestion of sludge should be established to improve the anaerobic digestion of sludge and avoid inhibitory effects. This study investigated the effects of four representative NPs (i.e., nZVI, Ag NPs, Fe2O3 NPs and MgO NPs) on methane production during the anaerobic digestion of waste activated sludge (WAS). The presence of 10 mg/g total suspended solids (TSS) nZVI and 100 mg/g TSS Fe2O3 NPs increased methane production to 120% and 117% of the control, respectively, whereas 500 mg/g TSS Ag NPs and 500 mg/g TSS MgO NPs generated lower levels of methane production (73.52% and 1.08% that of the control, respectively). These results showed that low concentrations of nZVI and Fe2O3 NPs promoted the amount of microbes (Bacteria and Archaea) and activities of key enzymes but that higher concentrations of Ag NPs and MgO NPs inhibited them.

  20. Effects of Metal Nanoparticles on Methane Production from Waste-Activated Sludge and Microorganism Community Shift in Anaerobic Granular Sludge

    PubMed Central

    Wang, Tao; Zhang, Dong; Dai, Lingling; Chen, Yinguang; Dai, Xiaohu

    2016-01-01

    Extensive use of nanoparticles (NPs) in consumer and industrial products has led to concerns about their potential environmental impacts; however, the influences of different NPs (e.g., nZVI (nano zero-valent iron), Ag NPs, Fe2O3 NPs and MgO NPs) on the anaerobic digestion of sludge have not yet been studied in depth. Additionally, a new guideline or the use of different NPs in the anaerobic digestion of sludge should be established to improve the anaerobic digestion of sludge and avoid inhibitory effects. This study investigated the effects of four representative NPs (i.e., nZVI, Ag NPs, Fe2O3 NPs and MgO NPs) on methane production during the anaerobic digestion of waste activated sludge (WAS). The presence of 10 mg/g total suspended solids (TSS) nZVI and 100 mg/g TSS Fe2O3 NPs increased methane production to 120% and 117% of the control, respectively, whereas 500 mg/g TSS Ag NPs and 500 mg/g TSS MgO NPs generated lower levels of methane production (73.52% and 1.08% that of the control, respectively). These results showed that low concentrations of nZVI and Fe2O3 NPs promoted the amount of microbes (Bacteria and Archaea) and activities of key enzymes but that higher concentrations of Ag NPs and MgO NPs inhibited them. PMID:27166174

  1. Reduction of sludge generation by the addition of support material in a cyclic activated sludge system for municipal wastewater treatment.

    PubMed

    Araujo, Moacir Messias de; Lermontov, André; Araujo, Philippe Lopes da Silva; Zaiat, Marcelo

    2013-09-01

    An innovative biomass carrier (Biobob®) was tested for municipal wastewater treatment in an activated sludge system to evaluate the pollutant removal performance and the sludge generation for different carrier volumes. The experiment was carried out in a pilot-scale cyclic activated sludge system (CASS®) built with three cylindrical tanks in a series: an anoxic selector (2.1 m(3)), an aerobic selector (2.5 m(3)) and the main aerobic reactor (25.1 m(3)). The results showed that by adding the Biobob® carrier decreased the MLVSS concentration, which consequently reduced the waste sludge production of the system. Having 7% and 18% (v/v) support material in the aerobic reactor, the observed biomass yield decreased 18% and 36%, respectively, relative to the reactor operated with suspended biomass. The addition of media did not affect the system's performance for COD and TSS removal. However, TKN and TN removal were improved by 24% and 14%, respectively, using 18% (v/v) carrier. PMID:23831747

  2. Influence of hydraulic retention time on indigenous microalgae and activated sludge process.

    PubMed

    Anbalagan, Anbarasan; Schwede, Sebastian; Lindberg, Carl-Fredrik; Nehrenheim, Emma

    2016-03-15

    Integration of the microalgae and activated sludge (MAAS) process in municipal wastewater treatment and biogas production from recovered MAAS was investigated by studying the hydraulic retention time (HRT) of semi-continuous photo-bioreactors. An average total nitrogen (TN) removal efficiency (RE) of maximum 81.5 ± 5.1 and 64.6 ± 16.2% was achieved at 6 and 4 days HRT. RE of total phosphorous (TP) increased slightly at 6 days (80 ± 12%) HRT and stabilized at 4 days (56 ± 5%) and 2 days (55.5 ± 5.5%) HRT due to the fluctuations in COD and N/P mass ratio of the periodic wastewater. COD and organic carbon were removed efficiently and a rapidly settleable MAAS with a sludge volume index (SVI_10) of less than 117 mL g(-1) was observed at all HRTs. The anaerobic digestion of the untreated MAAS showed a higher biogas yield of 349 ± 10 mL g VS(-1) with 2 days HRT due to a low solids retention time (SRT). Thermal pretreatment of the MAAS (120 °C, 120 min) did not show any improvement with biogas production at 6 days (269 ± 3 (untreated) and 266 ± 16 (treated) mL gVS(-1)), 4 days (258 ± 11(untreated) and 263 ± 10 (treated) mL gVS(-1)) and 2 days (308 ± 19 mL (treated) gVS(-1)) HRT. Hence, the biogas potential tests showed that the untreated MAAS was a feasible substrate for biogas production. Results from this proof of concept support the application of MAAS in wastewater treatment for Swedish conditions to reduce aeration, precipitation chemicals and CO2 emissions. PMID:26803263

  3. Enrichment and activity of methanotrophic microorganisms from municipal wastewater sludge.

    PubMed

    Siniscalchi, Luciene Alves Batista; Vale, Isabel Campante; Dell'Isola, Jéssica; Chernicharo, Carlos Augusto; Calabria Araujo, Juliana

    2015-01-01

    In this study, methanotrophic microorganisms were enriched from a municipal wastewater sludge taken from an Upflow Anaerobic Sludge Blanket reactor. The enrichment was performed in a sequencing batch reactor (SBR) with an autotrophic medium containing nitrite and nitrate. The microbial community composition of the inoculum and of the enrichment culture after 100 days of SBR operation was investigated and compared with the help of data obtained from 454 pyrosequencing analyses. The nitrite and nitrate removal efficiencies were 68% and 53%, respectively, probably due to heterotrophic denitrification. Archaeal cells of the anaerobic methanotrophic Archaic (ANME)-I and ANME-II groups were detected by polymerase chain reaction throughout the whole cultivation period. Pyrosequencing analysis showed that community composition was different among the two samples analysed. The dominant phyla found in the inoculum were Synergistestes, Firmicutes and Euryarchaeota, while Planctomycetes, Verrucomicrobia, Chloroflexi and Proteobacteria prevailed in the enriched biomass. The cultivation conditions decreased Methanobacterium abundance from 8% to 1%, and enriched for methanotrophic bacteria such as Methylocaldum, Methylocistis and Methylosinus. Sequences of Methylocaldum sp. accounted for 2.5% of the total reads. The presence and high predominance of Verrucomicrobia in the enriched biomass suggested that other unknown methanotrophic species related to that phylum might also have occurred in the reactor. Anaerobic methane oxidation activity was measured for both samples, and showed that the activity of the enrichment culture was nearly three times higher than the activity of the inoculum. Taken together, these results showed that the inoculum type and cultivation conditions were properly suited for methanotrophic enrichment. PMID:25495866

  4. Fenton peroxidation improves the drying performance of waste activated sludge.

    PubMed

    Dewil, Raf; Baeyens, Jan; Neyens, Elisabeth

    2005-01-31

    Advanced sludge treatment processes (AST) reduce the amount of sludge produced and improve the dewaterability, thus probably also affecting the heat transfer properties and the drying characteristics of the sludge. This paper studies the influence of the Fenton peroxidation on the thermal conductivity of the sludge. Results demonstrate that the Fenton's peroxidation positively influences the sludge cake consistency and hence enhances the mechanical dewaterability and the drying characteristics of the dewatered sludge. For the two sludges used in this study, i.e. obtained from the wastewater treatment plants (WWTP) of Tienen and Sint-Niklaas--the dry solids content of the mechanically dewatered sludge increased from 22.5% to 40.3% and from 18.7% to 35.2%, respectively. The effective thermal conductivity k(e) of the untreated and the peroxidized sludges is measured and used to determine the heat transfer coefficient h(s). An average improvement for k(e) of 16.7% (Tienen) and 5.8% (Sint-Niklaas) was observed. Consequently the value of h(s) increased with 15.6% (Tienen) and 5.0% (Sint-Niklaas). This increased heat transfer coefficient in combination with the increased dewaterability has direct implications on the design of sludge dryers. A plate-to-plate calculation of a multiple hearth dryer illustrates that the number of plates required to dry the peroxidized sludge to 90% DS is less than half the number of plates needed to dry untreated sludge. This results in reduced dryer dimensions or a higher capacity for an existing dryer of given dimensions. PMID:15629575

  5. SUMMARY REPORT: THE CAUSES AND CONTROL OF ACTIVATED SLUDGE BULKING AND FOAMING

    EPA Science Inventory

    This 92-page Technology Transfer Summary Report provides reference material on the causes and controls of sludge bulking and foaming in activated sludge treatment that can be readily understood, and it includes sufficient detail to help plant operators control their systems. The ...

  6. Denitrification kinetics in anoxic/aerobic activated sludge systems

    SciTech Connect

    Horne, G.M.

    1998-12-11

    Nitrogen removal needs at municipal wastewater treatment plants (WWTPs) have increased due to greater concerns about eutrophication and increased interest in reuse of treated municipal effluents. Biological processes are the most cost-effective method for nitrogen removal. Biological nitrogen removal is accomplished in two distinctly different processes by the conversion of nitrogen in the wastewater from organic nitrogen and ammonia to nitrate, followed by reduction of the nitrate to nitrogen gas. Nitrate production occurs in an aerobic activated sludge treatment zone during a process called nitrification. The nitrate is then converted through a series of intermediate steps to nitrogen gas in an anoxic zone (an anaerobic condition with nitrate present) during a process called denitrification, effectively removing the nitrogen from the wastewater. Many different WWTP designs have been developed to incorporate these two conditions for nitrogen removal.

  7. Assessing the Nonbiodegradable Fraction of the Thickened Waste Activated Sludge.

    PubMed

    Elbeshbishy, Elsayed; Dhar, Bipro Ranjan; Nakhla, George

    2015-08-01

    In this study, the feasibility of using three methods to estimate the nonbiodegradable fraction of five thickened waste activated sludge (TWAS) samples was evaluated using long-term biochemical methane potential tests at four substrate to biomass ratios. The nonbiodegradable fraction was calculated based on the remaining volatile suspended solids (VSS), remaining total chemical oxygen demand (TCOD), and remaining total organic carbon (TOC). It was evident that the nonbiodegradable fraction of TWAS ranged from 12 to 27%. The average nonbiodegradable fractions of TWAS were 21, 18, and 23% based on remaining VSS, TCOD, and TOC, respectively. The proposed method can be potentially used to characterize biosolids for design and modeling anaerobic treatment processes. PMID:26237686

  8. Reducing the natural color of membrane bioreactor permeate with activated carbon or ozone.

    PubMed

    Abegglen, Christian; Joss, Adriano; Boehler, Marc; Buetzer, Simone; Siegrist, Hansruedi

    2009-01-01

    The suitability of two membrane bioreactors for on-site wastewater treatment and reuse in Switzerland was investigated. The treated wastewater was used for toilet flushing and gardening, with water recycling rates of 30% (single family house) and almost 100% (toilets in a cable car station) respectively. Due to the recycling, an increase in a natural yellowish-brown color was observed, leading to double flushing of the toilets, higher cleaning requirements and increased permeate production. Color removal with ozone, powdered (PAC) and granulated (GAC) activated carbon was assessed in laboratory and field experiments. PAC was added directly into the MBR, whereas ozonation and GAC were applied to the permeate. The dosage of ozone or activated carbon depended on the recycling rate and color intensity. If color removal is necessary, PAC is the option best suited to small treatment plants, with a requirement of 30-50 g m(-3) for 30% and 100 g m(-3) for 100% water recycling. PMID:19587413

  9. A stable, reusable, and highly active photosynthetic bioreactor by bio-interfacing an individual cyanobacterium with a mesoporous bilayer nanoshell.

    PubMed

    Jiang, Nan; Yang, Xiao-Yu; Deng, Zhao; Wang, Li; Hu, Zhi-Yi; Tian, Ge; Ying, Guo-Liang; Shen, Ling; Zhang, Ming-Xi; Su, Bao-Lian

    2015-05-01

    An individual cyanobacterium cell is interfaced with a nanoporous biohybrid layer within a mesoporous silica layer. The bio-interface acts as an egg membrane for cell protection and growth of outer shell. The resulting bilayer shell provides efficient functions to create a single cell photosynthetic bioreactor with high stability, reusability, and activity. PMID:25641812

  10. SLUDGE BATCH 7B QUALIFICATION ACTIVITIES WITH SRS TANK FARM SLUDGE

    SciTech Connect

    Pareizs, J.; Click, D.; Lambert, D.; Reboul, S.

    2011-11-16

    Waste Solidification Engineering (WSE) has requested that characterization and a radioactive demonstration of the next batch of sludge slurry - Sludge Batch 7b (SB7b) - be completed in the Shielded Cells Facility of the Savannah River National Laboratory (SRNL) via a Technical Task Request (TTR). This characterization and demonstration, or sludge batch qualification process, is required prior to transfer of the sludge from Tank 51 to the Defense Waste Processing Facility (DWPF) feed tank (Tank 40). The current WSE practice is to prepare sludge batches in Tank 51 by transferring sludge from other tanks. Discharges of nuclear materials from H Canyon are often added to Tank 51 during sludge batch preparation. The sludge is washed and transferred to Tank 40, the current DWPF feed tank. Prior to transfer of Tank 51 to Tank 40, SRNL typically simulates the Tank Farm and DWPF processes with a Tank 51 sample (referred to as the qualification sample). With the tight schedule constraints for SB7b and the potential need for caustic addition to allow for an acceptable glass processing window, the qualification for SB7b was approached differently than past batches. For SB7b, SRNL prepared a Tank 51 and a Tank 40 sample for qualification. SRNL did not receive the qualification sample from Tank 51 nor did it simulate all of the Tank Farm washing and decanting operations. Instead, SRNL prepared a Tank 51 SB7b sample from samples of Tank 7 and Tank 51, along with a wash solution to adjust the supernatant composition to the final SB7b Tank 51 Tank Farm projections. SRNL then prepared a sample to represent SB7b in Tank 40 by combining portions of the SRNL-prepared Tank 51 SB7b sample and a Tank 40 Sludge Batch 7a (SB7a) sample. The blended sample was 71% Tank 40 (SB7a) and 29% Tank 7/Tank 51 on an insoluble solids basis. This sample is referred to as the SB7b Qualification Sample. The blend represented the highest projected Tank 40 heel (as of May 25, 2011), and thus, the highest

  11. [Microbial composition of the activated sludges of the Moscow wastewater treatment plants].

    PubMed

    Kallistova, A Iu; Pimenov, N V; Kozlov, M N; Nikolaev, Iu A; Dorofeev, A G; Aseeva, V G; Grachev, V A; Men'ko, E V; Berestovskaia, Iu Iu; Nozhevnikova, A N; Kevbrina, M V

    2014-01-01

    The contribution of the major technologically important microbial groups (ammonium- and nitrite-oxidizing, phosphate-accumulating, foam-inducing, and anammox bacteria, as well as planctomycetes and methanogenic archaea) was characterized for the aeration tanks of the Moscow wastewater treatment facilities. FISH investigation revealed that aerobic sludges were eubacterial communities; the metabolically active archaea contributed insignificantly. Stage II nitrifying microorganisms and planctomycetes were significant constituents of the bacterial component of activated sludge, with Nitrobacter spp. being the dominant nitrifier. No metabolically active anammox bacteria were revealed in the sludge from aeration tanks. The sludge from the aeration tanks using different wastewater treatment technologies were found to differ in characteristics. Abundance of the nitrifying and phosphate-accumulating bacteria in the sludges generally correlated with microbial activity, in microcosms and with efficiency of nitrogen and phosphorus removal from wastewater. The highest microbial numbers and activity were found in the sludges of the tanks operating according to the technologies developed in the universities of Hanover and Cape Town. The activated sludge from the Novokur yanovo facilities, where abundant growth of filamentous bacteria resulted in foam formation, exhibited the lowest activity The group of foaming bacteria included Gordonia spp. and Acinetobacter spp., utilizing petroleum and motor oils, Sphaerotilus spp. utilizing unsaturated fatty acids, and Candidatus 'Microthrix parvicella'. Thus, the data on abundance and composition of metabolically active microorganisms obtained by FISH may be used for the technological control of wastewater treatment. PMID:25844473

  12. Nitrogen removal from wastewater and external waste activated sludge reutilization/reduction by simultaneous sludge fermentation, denitrification and anammox (SFDA).

    PubMed

    Wang, Bo; Peng, Yongzhen; Guo, Yuanyuan; Zhao, Mengyue; Wang, Shuying

    2016-08-01

    This work demonstrates the feasibility of simultaneous nitrogen removal and external waste activated sludge (WAS) reutilization/reduction by using the synergy of sludge fermentation, denitrification and anammox processes in up-flow reactors (SFDA). Pre-treated domestic wastewater and synthetic wastewater (containing nitrite ∼20mg/L, ammonium ∼10mg/L in both) were fed to 1# and 2# SFDA, respectively. Long-term operation of 1# SFDA was investigated with achieving the peak ammonium removal rate of 0.021 and nitrite removal rate of 0.081kgN/(m(3)d) as nitrogen loading rate elevated from 0.075 to 0.106kgN/(m(3)d). Negative effect of dissolved oxygen on anammox or fermentation in the 2# SFDA was demonstrated negligible due to rapid depletion by microorganisms. Furthermore, a "net" sludge reduction of 38.8% was obtained due to sludge decay and organics consumption by denitrification. The SFDA process was expected to potentially be used for nitrogen removal and WAS reutilization/reduction in full-scale application. PMID:27140818

  13. Activated sludge process: Waste treatment. (Latest citations from the Biobusiness database). Published Search

    SciTech Connect

    1996-01-01

    The bibliography contains citations concerning the use of the activated sludge process in waste and wastewater treatment. Topics include biochemistry of the activated sludge process, effects of various pollutants on process activity, effects of environmental variables such as oxygen and water levels, and nutrient requirements of microorganisms employed in activated sludge processes. The citations also explore use of the process to treat specific wastes, such as halocarbons, metallic wastes, and petrochemical effluents; and wastes from pharmaceutical and dairy processes. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  14. Activated sludge process: Waste treatment. (Latest citations from the Biobusiness database). Published Search

    SciTech Connect

    Not Available

    1993-10-01

    The bibliography contains citations concerning the use of the activated sludge process in waste and wastewater treatment. Topics include biochemistry of the activated sludge process, effects of various pollutants on process activity, effects of environmental variables such as oxygen and water levels, and nutrient requirements of microorganisms employed in activated sludge processes. The citations also explore use of the process to treat specific wastes, such as halocarbons, metallic wastes, and petrochemical effluents; and wastes from pharmaceutical and dairy processes. (Contains 250 citations and includes a subject term index and title list.)

  15. Activated sludge process: Waste treatment. (Latest citations from the Biobusiness database). Published Search

    SciTech Connect

    Not Available

    1993-07-01

    The bibliography contains citations concerning the use of the activated sludge process in waste and wastewater treatment. Topics include biochemistry of the activated sludge process, effects of various pollutants on process activity, effects of environmental variables such as oxygen and water levels, and nutrient requirements of microorganisms employed in activated sludge processes. The citations also explore use of the process to treat specific wastes, such as halocarbons, metallic wastes, and petrochemical effluents; and wastes from pharmaceutical and dairy processes. (Contains 250 citations and includes a subject term index and title list.)

  16. Tapered bed bioreactor

    DOEpatents

    Scott, Charles D.; Hancher, Charles W.

    1977-01-01

    A vertically oriented conically shaped column is used as a fluidized bed bioreactor wherein biologically catalyzed reactions are conducted in a continuous manner. The column utilizes a packing material a support having attached thereto a biologically active catalytic material.

  17. EVALUATION OF WASTE CITRUS ACTIVATED SLUDGE IN POULTRY FEEDS

    EPA Science Inventory

    Experiments were conducted on chick broilers and hens to determine the metabolizable energy of citrus sludge. A determination of metabolizable energy values showed that the values decreased as the level of citrus sludge in the diet increased. A series of protein levels were fed t...

  18. Activated Sludge. Selected Instructional Activities and References. Instructional Resources Monograph Series.

    ERIC Educational Resources Information Center

    Shepard, Clinton L.; Walasek, James B.

    This monograph contains a variety of selected materials related to wastewater treatment and water quality education and instruction. Part I presents a brief discussion of the activated sludge process in wastewater treatment operations. Part II, Instructional Units, contains selected portions of existing programs which may be utilized in…

  19. Treatment of coal gasification wastewater by membrane bioreactor hybrid powdered activated carbon (MBR–PAC) system.

    PubMed

    Jia, Shengyong; Han, Hongjun; Hou, Baolin; Zhuang, Haifeng; Fang, Fang; Zhao, Qian

    2014-12-01

    A laboratory-scale membrane bioreactor hybrid powdered activated carbon (MBR–PAC) system was developed to treat coal gasification wastewater to enhance the COD, total phenols (TPh), NH4+ removals and migrate the membrane fouling. Since the MBR–PAC system operated with PAC dosage of 4 g L−1, the maximum removal efficiencies of COD, TPh and NH4+ reached 93%, 99% and 63%, respectively with the corresponding influent concentrations of 2.27 g L−1, 497 mg L−1 and 164 mg N L−1; the PAC extraction efficiencies of COD, TPh and NH4+ were 6%, 3% and 13%, respectively; the transmembrane pressure decreased 34% with PAC after 50 d operation. The results demonstrate that PAC played a key role in the enhancement of biodegradability and mitigation of membrane fouling. PMID:25461944

  20. On the occurrence of anoxic microniches, denitrification, and sulfate reduction in aerated activated sludge

    SciTech Connect

    Schramm, A.; Santegoeds, C.M.; Nielsen, H.K.; Ploug, H.; Wagner, M.; Pribyl, M.; Wanner, J.; Amann, R.; De Beer, D.

    1999-09-01

    A combination of different methods was applied to investigate the occurrence of anaerobic processes in aerated activated sludge. Microsensor measurements (O{sub 2}, NO{sub 2}{sup {minus}}, NO{sub 3}{sup {minus}}, and H{sub 2}S) were performed on single sludge flocs to detect anoxic niches, nitrate reduction, or sulfate reduction on a microscale. Incubations of activated sludge with {sup 15}NO{sub 3}{sup {minus}} and {sup 35}SO{sub 4}{sup 2{minus}} were used to determine denitrification and sulfate reduction rates on a batch scale. In four of six investigated sludges, no anoxic zones developed during aeration, and consequently denitrification rates were very low. However, in two sludges anoxia in flocs coincided with significant denitrification rates. Sulfate reduction could not be detected in any sludge in either the microsensor or the batch investigation, not even under short-term anoxic conditions. In contrast, the presence of sulfate-reducing bacteria was shown by fluorescence in situ hybridization with 16S rRNA-targeted oligonucleotide probes and by PCR-based detection of genes coding for the dissimilatory sulfite reductase. A possible explanation for the absence of advection, i.e., facilitated by flow through pores and channels. This possibility is suggested by the irregularity of some oxygen profiles and by confocal laser scanning microscopy of the three-dimensional floc structures, which showed that flocs from the two sludges in which anoxic zones were found were apparently denser than flocs from the other sludges.

  1. A comparative evaluation of dried activated sludge and mixed dried activated sludge with rice husk silica to remove hydrogen sulfide

    PubMed Central

    2013-01-01

    The aim of this study was to investigate the effectiveness of dried activated sludge (DAS) and mixed dried activated sludge with rice husk silica (DAS & RHS) for removal of hydrogen sulfide (H2S). Two laboratory-scale filter columns (packed one litter) were operated. Both systems were operated under different conditions of two parameters, namely different inlet gas concentrations and different inlet flow rates. The DAS & RHS packed filter showed more than 99.96% removal efficiency (RE) with empty bed residence time (EBRT) of 45 to 90 s and 300 mg/L inlet concentration of H2S. However, the RE decreased to 96.87% with the EBRT of 30 s. In the same condition, the DAS packed filter showed 99.37% RE. Nonetheless, the RE was shown to have dropped to 82.09% with the EBRT of 30 s. The maximum elimination capacity (EC) was obtained in the DAS & RHS packed filter up to 52.32 g/m3h, with the RE of 96.87% and H2S mass loading rate of 54 g/m3h. The maximum EC in the DAS packed filter was obtained up to 44.33 g/m3h with the RE of 82.09% and the H2S mass loading rate of 54 g/m3h. After 53 days of operating time and 54 g/m3h of loading rates, the maximum pressure drop reached to 3.0 and 8.0 (mm H2O) for the DAS & RHS packed and DAS packed filters, respectively. Based on the findings of this study, the DAS & RHS could be considered as a more suitable packing material to remove H2S. PMID:23497048

  2. Sludge Retention Time as a Suitable Operational Parameter to Remove Both Estrogen and Nutrients in an Anaerobic–Anoxic–Aerobic Activated Sludge System

    PubMed Central

    Zeng, Qingling; Li, Yongmei; Yang, Shijia

    2013-01-01

    Abstract Estrogen in wastewater are responsible for a significant part of the endocrine-disrupting effects observed in the aquatic environment. The effect of sludge retention time (SRT) on the removal and fate of 17β-estradiol (E2) and 17α-ethinylestradiol (EE2) in an anaerobic–anoxic–oxic activated sludge system designed for nutrient removal was investigated by laboratory-scale experiments using synthetic wastewater. With a hydraulic retention time of 8 h, when SRT ranged 10–25 days, E2 was almost completely removed from water, and EE2 removal efficiency was 65%–81%. Both estrogens were easily sorbed onto activated sludge. Distribution coefficients (Kd) of estrogens on anaerobic sludge were greater than those on anoxic and aerobic sludges. Mass balance calculation indicated that 99% of influent E2 was degraded by the activated sludge process, and 1% remained in excess sludge; of influent EE2, 62.0%–80.1% was biodegraded; 18.9%–34.7% was released in effluent; and 0.88%–3.31% remained in excess sludge. Optimal SRT was 20 days for both estrogen and nutrient removal. E2 was almost completely degraded, and EE2 was only partly degraded in the activated sludge process. Residual estrogen on excess sludge must be considered in the sludge treatment and disposal processes. The originality of the work is that removal of nutrients and estrogens were linked, and optimal SRT for both estrogen and nutrient removal in an enhanced biological phosphorus removal system was determined. This has an important implication for the design and operation of full-scale wastewater treatment plants. PMID:23633892

  3. Sludge Retention Time as a Suitable Operational Parameter to Remove Both Estrogen and Nutrients in an Anaerobic-Anoxic-Aerobic Activated Sludge System.

    PubMed

    Zeng, Qingling; Li, Yongmei; Yang, Shijia

    2013-04-01

    Estrogen in wastewater are responsible for a significant part of the endocrine-disrupting effects observed in the aquatic environment. The effect of sludge retention time (SRT) on the removal and fate of 17β-estradiol (E2) and 17α-ethinylestradiol (EE2) in an anaerobic-anoxic-oxic activated sludge system designed for nutrient removal was investigated by laboratory-scale experiments using synthetic wastewater. With a hydraulic retention time of 8 h, when SRT ranged 10-25 days, E2 was almost completely removed from water, and EE2 removal efficiency was 65%-81%. Both estrogens were easily sorbed onto activated sludge. Distribution coefficients (K d) of estrogens on anaerobic sludge were greater than those on anoxic and aerobic sludges. Mass balance calculation indicated that 99% of influent E2 was degraded by the activated sludge process, and 1% remained in excess sludge; of influent EE2, 62.0%-80.1% was biodegraded; 18.9%-34.7% was released in effluent; and 0.88%-3.31% remained in excess sludge. Optimal SRT was 20 days for both estrogen and nutrient removal. E2 was almost completely degraded, and EE2 was only partly degraded in the activated sludge process. Residual estrogen on excess sludge must be considered in the sludge treatment and disposal processes. The originality of the work is that removal of nutrients and estrogens were linked, and optimal SRT for both estrogen and nutrient removal in an enhanced biological phosphorus removal system was determined. This has an important implication for the design and operation of full-scale wastewater treatment plants. PMID:23633892

  4. [Detection of anaerobic processes and microorganisms in immobilized activated sludge of a wastewater treatment plant with intense aeration].

    PubMed

    Litti, Iu V; Nekrasova, V K; Kulikov, N I; Siman'kova, M V; Nozhevnikova, A N

    2013-01-01

    Attached activated sludge from the Krasnaya Polyana (Sochi) wastewater treatment plant was studied after the reconstruction by increased aeration and water recycle, as well as by the installation of a bristle carrier for activated sludge immobilization. The activated sludge biofilms developing under conditions of intense aeration were shown to contain both aerobic and anaerobic microorganisms. Activity of a strictly anaerobic methanogenic community was revealed, which degraded organic compounds to methane, further oxidized by aerobic methanotrophs. Volatile fatty acids, the intermediates of anaerobic degradation of complex organic compounds, were used by both aerobic and anaerobic microorganisms. Anaerobic oxidation of ammonium with nitrite (anammox) and the presence of obligate anammox bacteria were revealed in attached activated sludge biofilms. Simultaneous aerobic and anaerobic degradation of organic contaminants by attached activated sludge provides for high rates of water treatment, stability of the activated sludge under variable environmental conditions, and decreased excess sludge formation. PMID:25509405

  5. Development of an ATP measurement method suitable for xenobiotic treatment activated sludge biomass.

    PubMed

    Nguyen, Lan Huong; Chong, Nyuk-Min

    2015-09-01

    Activated sludge consumes a large amount of energy to degrade a xenobiotic organic compound. By tracking the energy inventory of activated sludge biomass during the sludge's degradation of a xenobiotic, any disadvantageous effect on the sludge's performance caused by energy deficiency can be observed. The purpose of this study was to develop a reliable and accurate method for measuring the ATP contents of activated sludge cells that were to degrade a xenobiotic organic. Cell disruption and cellular ATP extraction were performed by a protocol with which xenobiotic degrading activated sludge biomass was washed with SDS, treated by Tris and TCA, and followed by bead blasting. The suspension of disrupted cells was filtered before the filtrate was injected into HPLC that was set at optimal conditions to measure the ATP concentration therein. This extraction protocol and HPLC measurement of ATP was evaluated for its linearity, limits of detection, and reproducibility. Evaluation test results reported a R(2) of 0.999 of linear fit of ATP concentration versus activated sludge concentration, a LOD=0.00045mg/L, a LOQ=0.0015mg/L for HPLC measurement of ATP, a MDL=0.46mg/g SS for ATP extraction protocol, and a recovery efficiency of 96.4±2%. This method of ATP measurement was simple, rapid, reliable, and was unburdened of some limitations other methods may have. PMID:26210584

  6. Bioproduction of volatile fatty acid from the fermentation of waste activated sludge for in situ denitritation.

    PubMed

    Wang, Bo; Peng, Yongzhen; Guo, Yuanyuan; Wang, Shuying

    2016-04-01

    Waste activated sludge (WAS) fermentation integrated with denitritation (the reduction of nitrite to dinitrogen gas) at different pHs was investigated in batch-mode reactors over a 24-day period. The results showed that in comparison with controlled pHs, the volatile fatty acid (VFA) bioproduction for in situ denitritation was significantly improved at uncontrolled pH. VFA fermented from WAS was quickly consumed by denitritation at uncontrolled pH, which accelerated sludge degradation. On the other hand, sludge digestion was benefited from the alkalinity produced from denitritation, while methanogenesis was prohibited by alkalinity and nitrite. The integrated sludge fermentation and denitritation can be cost-effectively applied to wastewater treatment plants, so that organic substrates (e.g., VFAs) are produced for denitritation via simultaneous sludge fermentation, which enables WAS reutilization and enhances nitrogen removal efficiency without the need of external carbon sources. PMID:26475401

  7. Influence of Copper Nanoparticles on the Physical-Chemical Properties of Activated Sludge

    PubMed Central

    Chen, Hong; Zheng, Xiong; Chen, Yinguang; Li, Mu; Liu, Kun; Li, Xiang

    2014-01-01

    The physical-chemical properties of activated sludge, such as flocculating ability, hydrophobicity, surface charge, settleability, dewaterability and bacteria extracellular polymer substances (EPS), play vital roles in the normal operation of wastewater treatment plants (WWTPs). The nanoparticles released from commercial products will enter WWTPs and can induce potential adverse effects on activated sludge. This paper focused on the effects of copper nanoparticles (CuNPs) on these specific physical-chemical properties of activated sludge. It was found that most of these properties were unaffected by the exposure to lower CuNPs concentration (5 ppm), but different observation were made at higher CuNPs concentrations (30 and 50 ppm). At the higher CuNPs concentrations, the sludge surface charge increased and the hydrophobicity decreased, which were attributed to more Cu2+ ions released from the CuNPs. The carbohydrate content of EPS was enhanced to defense the toxicity of CuNPs. The flocculating ability was found to be deteriorated due to the increased cell surface charge, the decreased hydrophobicity, and the damaged cell membrane. The worsened flocculating ability made the sludge flocs more dispersed, which further increased the toxicity of the CuNPs by increasing the availability of the CuNPs to the bacteria present in the sludge. Further investigation indicated that the phosphorus removal efficiency decreased at higher CuNPs concentrations, which was consistent with the deteriorated physical-chemical properties of activated sludge. It seems that the physical-chemical properties can be used as an indicator for determining CuNPs toxicity to the bacteria in activated sludge. This work is important because bacteria toxicity effects to the activated sludge caused by nanoparticles may lead to the deteriorated treatment efficiency of wastewater treatment, and it is therefore necessary to find an easy way to indicate this toxicity. PMID:24663333

  8. Molecularly imprinted polymer microspheres enhanced biodegradation of bisphenol A by acclimated activated sludge.

    PubMed

    Xie, Ya-ting; Li, Hai-bin; Wang, Ling; Liu, Qian; Shi, Yun; Zheng, Hai-yan; Zhang, Meng; Wu, Ya-ting; Lu, Bin

    2011-01-01

    The impacts of bisphenol A- imprinted polymeric microspheres (MIPMs) on the biodegradation of bisphenol A by acclimated activated sludge were studied. Due to the selective adsorption of MIPMs to bisphenol A (BPA) and its analogues, addition of MIPMs to activated sludge increased levels of BPA and its metabolites, which were also the substrates of biodegradation. Higher substrates (BPA and its metabolites) level promoted biodegradation efficiencies of activated sludge via accelerating removal speed of BPA and its metabolites, increasing degradation rate and decreasing half-lives of biodegradation. The enhancement of MIPMs in degradation efficiencies was more significant in environmental water containing low-level of pollutants, and water containing interferences such as heavy metals and humic acid. Furthermore, MIPMs were more suitable than non-selective sorbents such as active carbon to be used as enhancer for BPA biodegradation. MIPMs combined with activated sludge are simple, effective, environmental-friendly processes to biodegrade low-level pollutants in environmental water. PMID:21131017

  9. [Using Excess Activated Sludge Treated 4-Chlorophenol Contained Waste Water to Cultivate Chlorella vulgaris].

    PubMed

    Wang, Lu; Chen, Xiu-rong; Yan, Long; He, Yi-xuan; Shi, Zhen-dong

    2015-04-01

    Using different rations of sludge extracts and supernate from 4-Chlorophenol (4-CP) simulated wastewater's excess sludge after centrifugation to cultivate the Chlorella vulgaris to achieve the goal of excess sludge utilization together with chlorella cultivating. The experiments were performed in 500 mL flasks with different rations of sludge extracts & BG-11 and supernate & BG-11 in a light growth chamber respectively. Number of algal cells, Chlorophyll, enzyme activity, oil and water total nitrogen (TN), total phosphorus (TP), total organic carbon (TOC), toxicity index were investigated. Result showed that the nutrition supplies and toxicity in the excess sludge were removed efficiently via Chlorella vulgaris, the removal rates of TN and TP were at least 40% and 90% respectively; After 10 days cultivation, the density growth of 50% sludge extracts was 20 times higher of the beginning while its chlorophyll content was lower than that of the blank group. Sludge extracts could promote the proliferation of algae, but were not conducive to the synthesis of chlorophyll. The quantity of SOD in per cell showed Chlorella vulgaris gave a positive response via stimulation from toxicant in sludge extracts and supernate. The best time for collecting chlorella vulgaris was the fifth day of cultivation, taking neutral oil accumulation as the evaluating indicator for its utilization combined with the removal of supplies and toxicity. PMID:26164919

  10. Performance of calcium peroxide for removal of endocrine-disrupting compounds in waste activated sludge and promotion of sludge solubilization.

    PubMed

    Zhang, Ai; Wang, Jie; Li, Yongmei

    2015-03-15

    Removal of six phenolic endocrine disrupting compounds (EDCs) (estrone, 17β-estradiol, 17α-ethinylestradiol, estriol, bisphenol A, and 4-nonylphenols) from waste activated sludge (WAS) was investigated using calcium peroxide (CaO2) oxidation. Effects of initial pH and CaO2 dosage were investigated. The impacts of CaO2 treatment on sludge solubilization and anaerobic digestion were also evaluated. Specifically, the role of reactive oxygen species (ROS) in EDC degradation during CaO2 oxidation was tested. Effects of 6 metal ions contained in the sludge matrix on EDC degradation were also evaluated. The results showed that CaO2 treatment can be a promising technology for EDC removal and facilitating sludge reuse. The EDC removal efficiencies increased with the increase in CaO2 dosage. At CaO2 doses of more than 0.34 g per gram of total solid (g g(-1) TS), more than 50% of EDCs were removed in a wide pH range of 2-12. Higher removal efficiencies were achieved at initial pH values of 12 and 2. The products of EDCs during CaO2 oxidation had less estrogenic activity than the originals. Under the conditions of neutral pH and CaO2 dosage = 0.34 g g(-1) TS, the sludge solubilization can be improved by increasing the soluble total organic carbon (STOC) and volatile suspended solids (VSS) reduction by 25% and 27% in 7 d, respectively; the volatile fatty acid (VFA) production was enhanced by 96% in the 15 d following anaerobic digestion. The ROS released by CaO2 are the main factors contributing to EDC removal, among which, hydroxyl radicals (OH) play the most important role. Metal ions contained in the sludge matrix also affected EDC removal. For most cases, Fe, Cu, and Zn had positive effects; Mn and Ag had negative effects; and Mg had an insignificant effect on EDC removal. PMID:25613412

  11. Incorporation of hydrophobized mineral particles in activated sludge flocs: a way to assess ballasting efficiency.

    PubMed

    Defontaine, G; Thormann, J; Lartiges, B S; El Samrani, A G; Barrs, O

    2005-01-01

    The role of mineral surface hydrophobicity in attachment to activated sludge flocs was investigated. Fluorite and quartz particles of similar granulometry were hydrophobized by adsorbing sodium oleate and dodecylamine chloride, respectively. Mineral hydrophobicity was assessed by flotation expriments. The attachment of particles to microbial flocs was determined by optical microscopy. The results indicate that hydrophobized particles are always better incorporated within activated sludge flocs than non-coated particles. A comparison with Aquatal particles used as sludge ballast reveals that hydrophobized minerals are associated with microbial flocs to the same extent. PMID:16459790

  12. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Laptop computer sits atop the Experiment Control Computer for a NASA Bioreactor. The flight crew can change operating conditions in the Bioreactor by using the graphical interface on the laptop. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  13. [Activated Sludge Bacteria Transforming Cyanopyridines and Amides of Pyridinecarboxylic Acids].

    PubMed

    Demakov, V A; Vasil'ev, D M; Maksimova, Yu G; Pavlova, Yu A; Ovechkina, G V; Maksimov, A Yu

    2015-01-01

    Species diversity of bacteria from the activated sludge of Perm biological waste treatment facilities capable of transformation of cyanopyridines and amides of pyridinecarboxylic acids was investigated. Enrichment cultures in mineral media with 3-cyanopyridine as the sole carbon and nitrogen source were used to obtain 32 clones of gram-negative heterotrophic bacteria exhibiting moderate growth on solid and liquid media with 3- and 4-cyanopyridine. Sequencing of the 16S rRNA gene fragments revealed that the clones with homology of at least 99% belonged to the genera Acinetobacte, Alcaligenes, Delftia, Ochrobactrum, Pseudomonas, Stenotrophomonas, and Xanthobacter. PCR analysis showed that 13 out of 32 isolates contained the sequences (-1070 bp) homologous to the nitrilase genes reported previously in Alcaligenes faecalis JM3 (GenBank, D13419.1). Nine clones were capable of nitrile and amide transformation in minimal salt medium. Acinetobacter sp. 11 h and Alcaligenes sp. osv transformed 3-cyanopyridine to nicotinamide, while most of the clones possessed amidase activity (0.5 to 46.3 mmol/(g h) for acetamide and 0.1 to 5.6 mmol/(g h) for nicotinamide). Nicotinamide utilization by strain A. faecalis 2 was shown to result in excretion of a secondary metabolite, which was identified as dodecyl acrylate at 91% probability. PMID:26263697

  14. Activated sludge studies of selected contaminants of PFH wastewater

    SciTech Connect

    Dudley, S.K.; Bustamante, R.B.; Bonner, W.P.

    1991-12-31

    Acetone, propionitrile, pyrrole, and thiocyanate were selected as representative compounds of wastewater expected from pressurized, fluidized-bed hydroretorting (PFH) of Eastern oil shales. The PFH process has been the subject of investigation by the Institute of Gas Technology, under contract with the United States Department of Energy, for the purpose of obtaining higher oil yields from Eastern shales than has been possible using conventional retorting methods. Preliminary batch experiments illustrated that acetone, propionitrile, pyrrole, and thiocyanate are aerobically biodegradable by heterogeneous microbiological cultures. Three continuous flow activated sludge reactors were used to further evaluate the biological treatability of the synthetic waste. The studies revealed that the compounds could be removed at hydraulic residence times of as low as one day. Three one-day experiments demonstrated that biological system`s capability to accept organic shock loadings without a change in effluent quality. A no-recycle reactor illustrated that the flocculent microbiological population had a high resistance to solids washout. Because a supplementary nitrogen source was not included in synthetic waste treated by the no-recycle unit, it was shown that propionitrile, pyrrole, and/or thiocyanate supplied the nitrogen necessary for biological activity.

  15. Activated sludge studies of selected contaminants of PFH wastewater

    SciTech Connect

    Dudley, S.K. ); Bustamante, R.B.; Bonner, W.P. )

    1991-01-01

    Acetone, propionitrile, pyrrole, and thiocyanate were selected as representative compounds of wastewater expected from pressurized, fluidized-bed hydroretorting (PFH) of Eastern oil shales. The PFH process has been the subject of investigation by the Institute of Gas Technology, under contract with the United States Department of Energy, for the purpose of obtaining higher oil yields from Eastern shales than has been possible using conventional retorting methods. Preliminary batch experiments illustrated that acetone, propionitrile, pyrrole, and thiocyanate are aerobically biodegradable by heterogeneous microbiological cultures. Three continuous flow activated sludge reactors were used to further evaluate the biological treatability of the synthetic waste. The studies revealed that the compounds could be removed at hydraulic residence times of as low as one day. Three one-day experiments demonstrated that biological system's capability to accept organic shock loadings without a change in effluent quality. A no-recycle reactor illustrated that the flocculent microbiological population had a high resistance to solids washout. Because a supplementary nitrogen source was not included in synthetic waste treated by the no-recycle unit, it was shown that propionitrile, pyrrole, and/or thiocyanate supplied the nitrogen necessary for biological activity.

  16. Combined System of Activated Sludge and Ozonation for the Treatment of Kraft E1 Effluent

    PubMed Central

    Assalin, Marcia Regina; dos Santos Almeida, Edna; Durán, Nelson

    2009-01-01

    The treatment of paper mill effluent for COD, TOC, total phenols and color removal was investigated using combined activated sludge-ozonation processes and single processes. The combined activated sludge-O3/pH 10 treatment was able to remove around 80% of COD, TOC and color from Kraft E1 effluent. For the total phenols, the efficiency removal was around 70%. The ozonation post treatment carried out at pH 8.3 also showed better results than the single process. The COD, TOC, color and total phenols removal efficiency obtained were 75.5, 59.1, 77 and 52.3%, respectively. The difference in the concentrations of free radical produced by activated sludge-O3/pH 10 and activated sludge-O3/pH 8.3 affected mainly the TOC and total phenol removal values. PMID:19440438

  17. EVIDENCE THAT MICROORGANISMS CAUSE INACTIVATION OF VIRUSES IN ACTIVATED SLUDGE (JOURNAL VERSION)

    EPA Science Inventory

    Virus loss in activated sludge appeared to be caused by microorganisms. This conclusion is supported by the finding that poliovirus infectivity decreased during incubation in mixed-liquor suspended solids, primarily because of a sedimentable, heat-sensitive component. Furthermore...

  18. Monitoring endocrine activity in kraft mill effluent treated by aerobic moving bed bioreactor system.

    PubMed

    Chamorro, S; Pozo, G; Jarpa, M; Hernandez, V; Becerra, J; Vidal, G

    2010-01-01

    A Moving Bed Bioreactor (MBBR) was operated at three different hydraulic retention times for a period of 414 days. The fate of the extractive compounds and the estrogenic activity of the Pinus radiata kraft mill effluents were evaluated using Yeast Estrogen Screen (YES) and gas chromatography - mass spectrometry (GC-MS) detection. Results show that the MBBR reactor is able to remove between 80-83% of estrogenic activity present in the kraft mill Pinus radiata influent, where the values of the effluent's estrogenic activity ranged between 0.123-0.411 ng L(-1), expressed as estrogenic equivalent (EEqs) of 17-a-ethynylestradiol (EE2 eq.). Additionally, the biomass of the MBBR reactor accumulated estrogenic activity ranging between 0.29-0.37 ng EEqs EE2 during the different Hydraulic Retention Time (HRT) operations. The main groups present in pulp mills effluents, corresponding to fatty acids, hydrocarbons, phenols, sterols and triterpenes, were detected by solid phase extraction (SPE) and gas chromatography - mass spectrometry (GC-MS). The results suggest that the sterols produce the estrogenic activity in the evaluated effluent. PMID:20595766

  19. Effect of humic acid in leachate on specific methanogenic activity of anaerobic granular sludge.

    PubMed

    Guo, Mengfei; Xian, Ping; Yang, Longhui; Liu, Xi; Zhan, Longhui; Bu, Guanghui

    2015-01-01

    In order to find out the effects of humic acid (HA) in anaerobic-treated landfill leachate on granular sludge, the anaerobic biodegradability of HA as well as the influences of HA on the total cumulative methane production, the anaerobic methanization process and the specific methanogenic activity (SMA) of granular sludge are studied in this paper. Experimental results show that as a non-biodegradable organic pollutant, HA is also difficult to be decomposed by microbes in the anaerobic reaction process. Presence of HA and changes in the concentration have no significant influences on the total cumulative methane production and the anaerobic methanization process of granular sludge. Besides, the total cumulative methane production cannot reflect the inhibition of toxics on the methanogenic activity of granular sludge on the premise of sufficient reaction time. Results also show that HA plays a promoting role on SMA of granular sludge. Without buffering agent the SMA value increased by 19.2% on average due to the buffering and regulating ability of HA, while with buffering agent the SMA value increased by 5.4% on average due to the retaining effect of HA on the morphology of the sludge particles. However, in the presence of leachate the SMA value decreased by 27.6% on average, because the toxic effect of the toxics in the leachate on granular sludge is much larger than the promoting effect of HA. PMID:25915186

  20. Comparison of extracellular polymeric substances (EPS) extraction from two different activated sludges.

    PubMed

    Zhang, Leiyan; Ren, Hongqiang; Ding, Lili

    2012-01-01

    The characteristics of extracellular polymeric substances (EPS) extracted with five different extraction protocols from two different activated sludges were studied. The results showed that the major EPS constituent extracted by centrifugation was protein for the sludge in sequencing batch reactor treating chemical wastewater, and nucleic acid for the sludge in moving bed biofilm reactor treating synthetic urban wastewater. The order of EPS extraction amounting from the two sludges was formaldehyde + NaOH > formaldehyde + heating > EDTA > heating > centrifugation. The different extraction methods, the wastewater type, and activated sludge source greatly affected the amount and composition of EPS. The chemical extracted methods were more effective than the physical methods in extracting EPS for the two sludges. Moreover, formaldehyde combined NaOH was most effective in extracting EPS for the two sludges. However, chemical extraction could contaminate the EPS solution, which was pointed out by infra-red analysis and was also proved by cell lyses during EPS extraction and carrying over of the chemical extractant. Therefore, this study highlights that the choice of EPS extraction method should consider both the extraction yield and content and the contamination of extracting reagents to the EPS solution. The extraction procedures should be optimized and most effective. PMID:22864444

  1. Biotransformation and adsorption of pharmaceutical and personal care products by activated sludge after correcting matrix effects.

    PubMed

    Deng, Yu; Li, Bing; Yu, Ke; Zhang, Tong

    2016-02-15

    This study reported significant suppressive matrix effects in analyses of six pharmaceutical and personal care products (PPCPs) in activated sludge, sterilized activated sludge and untreated sewage by ultra-performance liquid chromatography-tandem mass spectrometry. Quantitative matrix evaluation on selected PPCPs supplemented the limited quantification data of matrix effects on mass spectrometric determination of PPCPs in complex environment samples. The observed matrix effects were chemical-specific and matrix-dependent, with the most pronounced average effect (-55%) was found on sulfadiazine in sterilized activated sludge. After correcting the matrix effects by post-spiking known amount of PPCPs, the removal mechanisms and biotransformation kinetics of selected PPCPs in activated sludge system were revealed by batch experiment. Experimental data elucidated that the removal of target PPCPs in the activated sludge process was mainly by biotransformation while contributions of adsorption, hydrolysis and volatilization could be neglected. High biotransformation efficiency (52%) was observed on diclofenac while other three compounds (sulfadiazine, sulfamethoxazole and roxithromycin) were partially biotransformed by ~40%. The other two compounds, trimethoprim and carbamazepine, showed recalcitrant to biotransformation of the activated sludge. PMID:26706769

  2. Biodegradation of imidazolium ionic liquids by activated sludge microorganisms.

    PubMed

    Liwarska-Bizukojc, Ewa; Maton, Cedric; Stevens, Christian V

    2015-11-01

    Biological properties of ionic liquids (ILs) have been usually tested with the help of standard biodegradation or ecotoxicity tests. So far, several articles on the identification of intermediate metabolites of microbiological decay of ILs have been published. Simultaneously, the number of novel ILs with unrecognized characteristics regarding biodegradability and effect on organisms and environment is still increasing. In this work, seven imidazolium ionic liquids of different chemical structure were studied. Three of them are 1-alkyl-3-methyl-imidazolium bromides, while the other four are tetra- or completely substituted imidazolium iodides. This study focused on the identification of intermediate metabolites of the aforementioned ionic liquids subjected to biodegradation in a laboratory activated sludge system. Both fully substituted ionic liquids and 1-ethyl-3-methyl-imidazolium bromide were barely biodegradable. In the case of two of them, no biotransformation products were detected. The elongation of the alkyl side chain made the IL more susceptible for microbiological decomposition. 1-Decyl-3-methyl-imidazolium bromide was biotransformed most easily. Its primary biodegradation up to 100 % could be achieved. Nevertheless, the cleavage of the imidazolium ring has not been observed. PMID:26463469

  3. Aerobic activated sludge transformation of methotrexate: identification of biotransformation products.

    PubMed

    Kosjek, Tina; Negreira, Noelia; de Alda, Miren López; Barceló, Damià

    2015-01-01

    This study describes the biotransformation of cytostatic and immunosuppressive pharmaceutical methotrexate. Its susceptibility to microbiological breakdown was studied in a batch biotransformation system, in presence or absence of carbon source and at two activated sludge concentrations. The primary focus of the present study are methotrexate biotransformation products, which were tentatively identified by the ultra-high performance liquid chromatography-quadrupole--Orbitrap-MS. Data-dependent experiments, combining full-scan MS data with product ion spectra were acquired, in order to identify the molecular ions of methotrexate transformation products, to propose the molecular formulae and to elucidate their chemical structures. Among the identified transformation products 2,4-diamino-N10-methyl-pteroic acid is most abundant and persistent. Other biotransformation reactions involve demethylation, oxidative cleavage of amine, cleavage of C-N bond, aldehyde to carboxylate transformation and hydroxylation. Finally, a breakdown pathway is proposed, which shows that most of methotrexate breakdown products retain the diaminopteridine structural segment. In total we propose nine transformation products, among them eight are described as methotrexate transformation products for the first time. PMID:24835159

  4. A hundred years of activated sludge: time for a rethink

    PubMed Central

    Sheik, Abdul R.; Muller, Emilie E. L.; Wilmes, Paul

    2014-01-01

    Biological wastewater treatment plants (BWWTPs) based on the activated sludge (AS) process have dramatically improved worldwide water sanitation despite increased urbanization and industrialization. However, current AS-based operations are considered economically and environmentally unsustainable. In this Perspective, we discuss our current understanding of microbial populations and their metabolic transformations in AS-based BWWTPs in view of developing more sustainable processes in the future. In particular, much has been learned over the course of the past 25 years about specialized microorganisms, which could be more comprehensively leveraged to recover energy and/or nutrients from wastewater streams. To achieve this, we propose a bottom-up design approach, focused around the concept of a “wastewater biorefinery column”, which would rely on the engineering of distinct ecological niches into a BWWTP in order to guarantee the targeted enrichment of specific organismal groups which in turn will allow the harvest of high-value resources from wastewater. This concept could be seen as a possible grand challenge to microbial ecologists and engineers alike at the centenary of the discovery of the AS process. PMID:24624120

  5. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Close-up view of the interior of a NASA Bioreactor shows the plastic plumbing and valves (cylinders at right center) to control fluid flow. The rotating wall vessel is at top center. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  6. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Biotechnology Refrigerator that preserves samples for use in (or after culturing in) the NASA Bioreactor. The unit is shown extracted from a middeck locker shell. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  7. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Interior view of the gas supply for the NASA Bioreactor. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  8. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Biotechnology Refrigerator that preserves samples for use in (or after culturing in) the NASA Bioreactor. The unit is shown extracted from a middeck locker shell and with thermal blankets partially removed. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  9. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Interior of a Biotechnology Refrigerator that preserves samples for use in (or after culturing in) the NASA Bioreactor. The unit is shown extracted from a middeck locker shell. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  10. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Electronics control module for the NASA Bioreactor. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  11. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Exterior view of the NASA Bioreactor Engineering Development Unit flown on Mir. The rotating wall vessel is behind the window on the face of the large module. Control electronics are in the module at left; gas supply and cooling fans are in the module at back. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  12. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Close-up view of the interior of a NASA Bioreactor shows the plastic plumbing and valves (cylinders at center) to control fluid flow. A fresh nutrient bag is installed at top; a flattened waste bag behind it will fill as the nutrients are consumed during the course of operation. The drive chain and gears for the rotating wall vessel are visible at bottom center center. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  13. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Biotechnology Refrigerator (BTR) holds fixed tissue culture bags at 4 degrees C to preserve them for return to Earth and postflight analysis. The cultures are used in research with the NASA Bioreactor cell science program. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC).

  14. Ultrasonic waste activated sludge disintegration for recovering multiple nutrients for biofuel production.

    PubMed

    Xie, Guo-Jun; Liu, Bing-Feng; Wang, Qilin; Ding, Jie; Ren, Nan-Qi

    2016-04-15

    Waste activated sludge is a valuable resource containing multiple nutrients, but is currently treated and disposed of as an important source of pollution. In this work, waste activated sludge after ultrasound pretreatment was reused as multiple nutrients for biofuel production. The nutrients trapped in sludge floc were transferred into liquid medium by ultrasonic disintegration during first 30 min, while further increase of pretreatment time only resulted in slight increase of nutrients release. Hydrogen production by Ethanoligenens harbinense B49 from glucose significantly increased with the concentration of ultrasonic sludge, and reached maximum yield of 1.97 mol H2/mol glucose at sludge concentration of 7.75 g volatile suspended solids/l. Without addition of any other chemicals, waste molasses rich in carbohydrate was efficiently turned into hydrogen with yield of 189.34 ml H2/g total sugar by E. harbinense B49 using ultrasonic sludge as nutrients. The results also showed that hydrogen production using pretreated sludge as multiple nutrients was higher than those using standard nutrients. Acetic acid produced by E. harbinense B49 together with the residual nutrients in the liquid medium were further converted into hydrogen (271.36 ml H2/g total sugar) by Rhodopseudomonas faecalis RLD-53 through photo fermentation, while ethanol was the sole end product with yield of 220.26 mg/g total sugar. Thus, pretreated sludge was an efficient nutrients source for biofuel production, which could replace the standard nutrients. This research provided a novel strategy to achieve environmental friendly sludge disposal and simultaneous efficient biofuel recovery from organic waste. PMID:26896823

  15. Rotating Bioreactor

    NASA Technical Reports Server (NTRS)

    1988-01-01

    The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues currently being cultured in rotating bioreactors by investigators.

  16. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    The heart of the bioreactor is the rotating wall vessel, shown without its support equipment. Volume is about 125 mL. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  17. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Astronaut John Blaha replaces an exhausted media bag and filled waste bag with fresh bags to continue a bioreactor experiment aboard space station Mir in 1996. NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators. This image is from a video downlink. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC).

  18. Is anaerobic digestion effective for the removal of organic micropollutants and biological activities from sewage sludge?

    PubMed

    Gonzalez-Gil, L; Papa, M; Feretti, D; Ceretti, E; Mazzoleni, G; Steimberg, N; Pedrazzani, R; Bertanza, G; Lema, J M; Carballa, M

    2016-10-01

    The occurrence of emerging organic micropollutants (OMPs) in sewage sludge has been widely reported; nevertheless, their fate during sludge treatment remains unclear. The objective of this work was to study the fate of OMPs during mesophilic and thermophilic anaerobic digestion (AD), the most common processes used for sludge stabilization, by using raw sewage sludge without spiking OMPs. Moreover, the results of analytical chemistry were complemented with biological assays in order to verify the possible adverse effects (estrogenic and genotoxic) on the environment and human health in view of an agricultural (re)use of digested sludge. Musk fragrances (AHTN, HHCB), ibuprofen (IBP) and triclosan (TCS) were the most abundant compounds detected in sewage sludge. In general, the efficiency of the AD process was not dependent on operational parameters but compound-specific: some OMPs were highly biotransformed (e.g. sulfamethoxazole and naproxen), while others were only slightly affected (e.g. IBP and TCS) or even unaltered (e.g. AHTN and HHCB). The MCF-7 assay evidenced that estrogenicity removal was driven by temperature. The Ames test did not show point mutation in Salmonella typhimurium while the Comet test exhibited a genotoxic effect on human leukocytes attenuated by AD. This study highlights the importance of combining chemical analysis and biological activities in order to establish appropriate operational strategies for a safer disposal of sewage sludge. Actually, it was demonstrated that temperature has an insignificant effect on the disappearance of the parent compounds while it is crucial to decrease estrogenicity. PMID:27344252

  19. Parameter identification and modeling of the biochemical methane potential of waste activated sludge.

    PubMed

    Appels, Lise; Lauwers, Joost; Gins, Geert; Degrève, Jan; Van Impe, Jan; Dewil, Raf

    2011-05-01

    Anaerobic digestion is widely used in waste activated sludge treatment. In this paper, partial least-squares (PLS) is employed to identify the parameters that are determining the biochemical methane potential (BMP) of waste activated sludge. Moreover, a model is developed for the prediction of the BMP. A strong positive correlation is observed between the BMP and volatile fatty acids and carbohydrate concentrations in the sludge. A somewhat weaker correlation with COD is also present. Soluble organics (sCOD, soluble carbohydrates and soluble proteins) were shown not to influence the BMP in the observed region. This finding could be most-valuable in the context of application of sludge pretreatment methods. The obtained model was able to satisfactory predict the BMP. PMID:21476497

  20. Comparison of imidazolium ionic liquids and traditional organic solvents: effect on activated sludge processes.

    PubMed

    Gendaszewska, Dorota; Liwarska-Bizukojc, Ewa

    2013-01-01

    Data concerning the biodegradability and ecotoxicity of ionic liquids (ILs) obtained so far are insufficient in the context of IL removal from wastewater in activated sludge systems. Thus, in this work the selected imidazolium ionic liquids and two organic solvents (methanol and acetone) were tested with respect to their influence on activated sludge processes, particularly on the morphology of sludge flocs. The presence of ionic liquids with the chemical structure of 1-alkyl-3-methyl imidazolium bromide in wastewater did not deteriorate biological wastewater treatment processes if their concentration was not higher than 5 mg l(-1). Regarding the structure of the ILs studied, the longer the alkyl substituent was, the stronger the effect on sludge flocs. The highest decrease in activated sludge floc area and biomass concentration was exerted by the ionic liquid with the longest alkyl chain, i.e. 1-decyl-3-methylimidazolium bromide. The action of both methanol and acetone on floc size, activated sludge concentration and efficiency of organic pollutants removal was weaker compared to all tested 1-alkyl-3-methyl imidazolium bromides. PMID:24355854

  1. Activated packed bed bioreactor for rapid nitrification in brackish water hatchery systems.

    PubMed

    Kumar, V J Rejish; Achuthan, Cini; Manju, N J; Philip, Rosamma; Singh, I S Bright

    2009-03-01

    A packed bed bioreactor (PBBR) was developed for rapid establishment of nitrification in brackish water hatchery systems in the tropics. The reactors were activated by immobilizing ammonia-oxidizing (AMONPCU-1) and nitrite-oxidizing (NIONPCU-1) bacterial consortia on polystyrene and low-density polyethylene beads, respectively. Fluorescence in situ hybridization demonstrated the presence of autotrophic nitrifiers belong to Nitrosococcus mobilis, lineage of beta ammonia oxidizers and nitrite oxidizer Nitrobacter sp. in the consortia. The activated reactors upon integration to the hatchery system resulted in significant ammonia removal (P < 0.01) culminating to its undetectable levels. Consequently, a significantly higher percent survival of larvae was observed in the larval production systems. With spent water the reactors could establish nitrification with high percentage removal of ammonia (78%), nitrite (79%) and BOD (56%) within 7 days of initiation of the process. PBBR is configured in such a way to minimize the energy requirements for continuous operation by limiting the energy inputs to a single stage pumping of water and aeration to the aeration cells. The PBBR shall enable hatchery systems to operate under closed recirculating mode and pave the way for better water management in the aquaculture industry. PMID:19039611

  2. Protists as bioindicators in activated sludge: Identification, ecology and future needs.

    PubMed

    Foissner, Wilhelm

    2016-08-01

    When the activated sludge process was developed, operators and scientists soon recognized protists as valuable indicators. However, only when Curds et al. (1968) showed with a few photographs the need of ciliates for a clear plant effluent, sewage protistology began to bloom but was limited by the need of species identification. Still, this is a major problem although several good guides are available. Thus, molecular kits should be developed for identification. Protists are indicators in two stages of wastewater treatment, viz., in the activated sludge and in the environmental water receiving the plant effluent. Continuous control of the protist and bacterial communities can prevent biological sludge foaming and bulking and may greatly save money for sludge oxygenation because several protist species are excellent indicators for the amount of oxygen present. The investigation of the effluent-receiving rivers gives a solid indication about the long term function of sewage works. The literature on protist bioindication in activated sludge is widely distributed. Thus, I compiled the data in a simple Table, showing which communities and species indicate good, mediocre, or poor plant performance. Further, many details on indication are provided, such as sludge loading and nitrifying conditions. Such specific features should be improved by appropriate statistics and more reliable identification of species. Then, protistologists have a fair chance to become important in wastewater works. Activated sludge is a unique habitat for particular species, often poorly or even undescribed. As an example, I present two new species. The first is a minute (∼30μm) Metacystis that makes an up to 300μm-sized mucous envelope mimicking a sludge floc. The second is a Phialina that is unique in having the contractile vacuole slightly posterior to mid-body. Finally, I provide a list of species which have the type locality in sewage plants. PMID:27062305

  3. Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, part II: multilayer biofilm diffusional model.

    PubMed

    Sen, Dipankar; Randall, Clifford W

    2008-07-01

    Research was undertaken to develop a diffusional model of the biofilm that can be applied in lieu of a semi-empirical model to upgrade an activated sludge system to an integrated fixed-film activated sludge (IFAS) or moving-bed biofilm reactor (MBBR) system. The model has been developed to operate with up to 12 cells (reactors) in series, with biofilm media incorporated to one or more of the zone cells, except the anaerobic zone cells. The values of the kinetic parameters for the model were measured using pilot-scale activated sludge, IFAS, and MBBR systems. The biofilm is divided into 12 layers and has a stagnant liquid layer. Diffusion and substrate utilization are calculated for each layer. The equations are solved simultaneously using a finite difference technique. The biofilm flux model is then linked to the activated sludge model. Advanced features include the ability to compute the biofilm thickness and the effect of biofilm thickness on performance. The biofilm diffusional model is also used to provide information and create a table of biofilm yields at different substrate concentrations that can be used in the semi-empirical model. PMID:18710146

  4. Influence of bulking agents and microbial activator on thermophilic aerobic transformation of sewage sludge.

    PubMed

    Pasda, N; Limtong, P; Oliver, R; Montange, D; Panichsakpatana, S

    2005-10-01

    Bangkok, while improving the wastewater treatment in order to alleviate the river pollution, faces important amounts of sewage sludge. The sewage sludge contains organic matter, nitrogen and phosphorus available for plant growth. However, it may contain pathogenic microorganisms. To be used for agricultural purposes, these pathogens should be destroyed, which can be achieved with the thermophilic phase of composting. As the sewage sludge is dense and unable to compost alone (low C/N ratio), it should be mixed with an organic by-product. Two by-products available in large quantities in Thailand (wood chips and rice husk) have been tested for mixture with sewage sludge. As these products are not easy to decompose (presence of silica in rice husk and lignin/tannins in wood chips), the addition of a microbial activator for composting has been tested in controlled conditions (small quantities of organic mixtures, 55 degrees C, moisture maintained at 60-70% of water holding capacity). The monitoring of the decomposition has been made by measuring the carbon dioxide respiration, pH, organic matter and nitrogen contents and the evolution of enzymatic activities. When mixed with sewage sludge, wood chips and rice husk do not show significant differences concerning decomposition after 63 days. The use of an activator within the experimental conditions does not improve the decomposition of organic matter contained in the mixture of sewage sludge and rice husk or wood chips. PMID:16342535

  5. Effect of PAC addition on sludge properties in an MBR treating high strength wastewater.

    PubMed

    Satyawali, Yamini; Balakrishnan, Malini

    2009-04-01

    This paper examines the sludge characteristics in a submerged membrane bioreactor (MBR) operated on a high strength wastewater from an alcohol distillery. Two membrane bioreactors, each with a 30 microm mesh filter, were investigated with and without addition of powdered activated carbon (PAC). Experiments were conducted with varying organic loading rates ranging from 3.4 to 6.9 kgCOD m(-3) day(-1) and the specific oxygen uptake rate (SOUR), sludge volume index (SVI), mixed liquor suspended solids (MLSS), particle size and extracellular polymeric substances (EPS) were monitored over a 180 day period. Respirometric experiments did not show enhancement in microbial activity with PAC supplementation. Addition of PAC decreased the SVI thereby perceptibly improving sludge dewaterability. The sludge particle size, which increased with time, appeared to be independent of PAC addition but was influenced by the aeration intensity. PAC also did not affect the sludge EPS concentration; however, the EPS composition, in terms of protein/carbohydrate (polysaccharide) ratio was altered resulting in a high P/C ratio. FTIR analysis of the sludge samples indicated that the functional groups associated with the sludge polysaccharides appear to be involved in its interaction with PAC. PMID:19201006

  6. Identical full-scale biogas-lift reactors (Blrs) with anaerobic granular sludge and residual activated sludge for brewery wastewater treatment and kinetic modeling.

    PubMed

    Xu, Fu; Huang, Zhenxing; Miao, Hengfeng; Ren, Hongyan; Zhao, Mingxing; Ruan, Wenquan

    2013-10-01

    Two identical full-scale biogas-lift reactors treating brewery wastewater were inoculated with different types of sludge to compare their operational conditions, sludge characteristics, and kinetic models at a mesophilic temperature. One reactor (R1) started up with anaerobic granular sludge in 12 weeks and obtained a continuously average organic loading rate (OLR) of 7.4 kg chemical oxygen demand (COD)/(m3 x day), COD removal efficiency of 80%, and effluent COD of 450 mg/L. The other reactor (R2) started up with residual activated sludge in 30 weeks and granulation accomplished when the reactor reached an average OLR of 8.3 kg COD/(m3 x day), COD removal efficiency of 90%, and effluent COD of 240 mg/L. Differences in sludge characteristics, biogas compositions, and biogas-lift processes may be accounted for the superior efficiency of the treatment performance of R2 over R1. Grau second-order and modified StoverKincannon models based on influent and effluent concentrations as well as hydraulic retention time were successfully used to develop kinetic parameters of the experimental data with high correlation coefficients (R2 > 0.95), which further showed that R2 had higher treatment performance than R1. These results demonstrated that residual activated sludge could be used effectively instead of anaerobic granular sludge despite the need for a longer time. PMID:24494489

  7. Aerobic thermophilic treatment of sewage sludge at pilot plant scale. 1. Operating conditions.

    PubMed

    Ponti, C; Sonnleitner, B; Fiechter, A

    1995-01-15

    The aerobic thermophilic treatment process of sewage sludge was studied at different bioreactor scales in a pilot plant installation. Since, for a satisfactory sludge disinfection, the Swiss legislation requires minimal incubation times of all volume elements, the bioreactors were operated in repetitive batch mode (draw and fill). Different retention times and frequencies of the volume changes were applied in order to prove the capability of the particular operation modes in assuring high degradative potential. The main enzymatic activity involved during the aerobic treatment was proteolysis: the RQ values ranged between 0.8 and 0.9 depending on the applied operating conditions. Although not in a linear manner, the efficiency of the microflora decreased as the bioreactor scale increased, when this increase corresponded with a reduction of the specific power input. The sludge oxidation rates can be tuned by some process operating conditions such as the volume change frequency, the changed volume quantities and the retention times. It was possible to improve the microbial degradative efficiency by an increased frequency of the changes, while the mean retention time influenced in particular the ultimate product quality, described as residual organic matter content of the sludge. The microflora present was also satisfactorily active at mean hydraulic retention times of less than 10 h. The organic matter concentration of the inlet sewage sludge plays an important role: it influences the aerobic degradation process positively. PMID:7765808

  8. Bioreactor principles

    NASA Technical Reports Server (NTRS)

    2001-01-01

    Cells cultured on Earth (left) typically settle quickly on the bottom of culture vessels due to gravity. In microgravity (right), cells remain suspended and aggregate to form three-dimensional tissue. The NASA Bioreactor provides a low turbulence culture environment which promotes the formation of large, three-dimensional cell clusters. The Bioreactor is rotated to provide gentle mixing of fresh and spent nutrient without inducing shear forces that would damage the cells. Due to their high level of cellular organization and specialization, samples constructed in the bioreactor more closely resemble the original tumor or tissue found in the body. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  9. [Research on the treatment of wastewater containing PVA by ozonation-activated sludge process].

    PubMed

    Xing, Xiao-Qiong; Huang, Cheng-Lan; Liu, Min; Chen, Ying

    2012-11-01

    The wastewater containing polyvinyl alcohol (PVA) was characterized with poor biodegradability, and was difficult to remove. In order to find an economically reasonable and practical technology, the research on the removal efficiency of different concentration wastewater containing PVA by ozonation-activated sludge process was studied, and the result was compared with the traditional activated sludge process. The results showed that the ozonation-activated sludge process was not suitable for treating influent with COD below 500 mg x L(-1) and the wastewater PVA concentration was 10-30 mg x L(-1). When the influent COD was between 500-800 mg x L(-1) and the PVA concentration was 15-60 mg x L(-1), the system had advantages on dealing with this kind of wastewater, and the average removal efficiency of COD and PVA were 92.8% and 57.4%, which were better than the traditional activated sludge process 4.1% and 15.2% respectively. In addition, the effluent concentrations of COD could keep between 30-60 mg x L(-1). When the influent COD was 1 000-1 200 mg x L(-1) and the PVA concentration was 20-70 mg x L(-1), the average removal efficiencies of COD and PVA were 90.9% and 45.3%, which were better than the traditional activated sludge process 12.8% and 12.1% respectively, but the effluent should to be further treated. Compared with the traditional activated sludge process, ozonation-activated sludge process had high treatment efficiency, stable running effect, and effectively in dealing with industrial wastewater containing PVA. PMID:23323416

  10. Roseomonas eburnea sp. nov., isolated from activated sludge.

    PubMed

    Wang, Chenghong; Deng, Shikai; Liu, Xin; Yao, Li; Shi, Chao; Jiang, Jin; Kwon, Soon-Wo; He, Jian; Li, Jiayou

    2016-01-01

    A Gram-stain-negative, aerobic, short rod-shaped, non-endospore-forming, ivory-pigmented and non-motile bacterium, designated strain BUT-5T, was isolated from activated sludge of an herbicides-manufacturing wastewater treatment facility in Jiangsu Province, China. The major fatty acids (>5 % of total fatty acids) were C16 : 0, C18 : 1 2-OH and summed feature 8 (C18 : 1ω7c and/or C18 : 1ω6c). The predominant respiratory quinone was ubiquinone Q-10. The polar lipids profile of strain BUT-5T included diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine, phosphatidylcholine and two unknown aminolipids. The DNA G+C content was 67.6 mol%. Phylogenetic analysis based on 16S rRNA gene sequences revealed that strain BUT-5T showed the highest sequence similarities to Roseomonas soli 5N26T (97.5 % 16S rRNA gene sequence similarity), followed by Roseomonas lacus TH-G33T (97.3 %) and Roseomonas terrae DS-48T (97.1 %). Strain BUT-5T showed low DNA-DNA relatedness with Roseomonas soli KACC 16376T (41 %), Roseomonas lacus KACC 11678T (46 %) and Roseomonas terrae KACC 12677T (42 %), respectively. On the basis of phenotypic and genotypic properties, as well as chemotaxonomic data, strain BUT-5T represents a novel species of the genus Roseomonas, for which the name Roseomonas eburnea sp. nov. is proposed. The type strain is BUT-5T ( = CCTCC AB2013276T = KACC 17166T). PMID:26530339

  11. Chryseomicrobium aureum sp. nov., a bacterium isolated from activated sludge.

    PubMed

    Deng, Shi-Kai; Ye, Xiao-Mei; Chu, Cui-Wei; Jiang, Jin; He, Jian; Zhang, Jun; Li, Shun-Peng

    2014-08-01

    A Gram-stain-positive, rod-shaped, non-motile, non-spore-forming, aerobic bacterial strain, designated BUT-2(T), was isolated from activated sludge of one herbicide-manufacturing wastewater-treatment facility in Kunshan, Jiangsu province, China, and subjected to polyphasic taxonomic studies. Analysis of the 16S rRNA gene sequence indicated that strain BUT-2(T) shared the highest similarity with Chryseomicrobium amylolyticum (98.98%), followed by Chryseomicrobium imtechense (98.88%), with less than 96% similarlity to members of the genera Paenisporosarcina, Planococcus, Sporosarcina and Planomicrobium. Phylogenetic analysis based on the 16S rRNA gene sequence showed that strain BUT-2(T) clustered with C. amylolyticum JC16(T) and C. imtechense MW10(T), occupying a distinct phylogenetic position. The major fatty acid (>10% of total fatty acids) type of strain BUT-2(T) was iso-C(15 : 0). The quinone system comprised menaquinone MK-7 (77.8%), MK-6 (11.9%) and MK-8 (10.3%). The polar lipids were diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine and some unidentified phospholipids. The cell-wall peptidoglycan type of strain BUT-2(T) was L-Orn-D-Glu. The genomic DNA G+C content of strain BUT-2(T) was 48.5 mol%. Furthermore, the DNA-DNA relatedness in hybridization experiments against the reference strain was lower than 70%, confirming that strain BUT-2(T) did not belong to previously described species of the genus Chryseomicrobium. On the basis of its morphological, physiological and chemotaxonomic characteristics as well as phylogenetic analysis, strain BUT-2(T) is considered to represent a novel species of the genus Chryseomicrobium, for which the name Chryseomicrobium aureum sp. nov. is proposed. The type strain is BUT-2(T) ( = CCTCC AB2013082(T) = KACC 17219(T)). PMID:24827708

  12. The production and characterization of a new active lipase from Acremonium alcalophilum using a plant bioreactor

    PubMed Central

    2013-01-01

    Background Microorganisms are the most proficient decomposers in nature, using secreted enzymes in the hydrolysis of lignocellulose. As such, they present the most abundant source for discovery of new enzymes. Acremonium alcalophilum is the only known cellulolytic fungus that thrives in alkaline conditions and can be cultured readily in the laboratory. Its optimal conditions for growth are 30°C and pH 9.0-9.2. The genome sequence of Acremonium alcalophilum has revealed a large number of genes encoding biomass-degrading enzymes. Among these enzymes, lipases are interesting because of several industrial applications including biofuels, detergent, food processing and textile industries. Results We identified a lipA gene in the genome sequence of Acremonium alcalophilum, encoding a protein with a predicted lipase domain with weak sequence identity to characterized enzymes. Unusually, the predicted lipase displays ≈ 30% amino acid sequence identity to both feruloyl esterase and lipase of Aspergillus niger. LipA, when transiently produced in Nicotiana benthamiana, accumulated to over 9% of total soluble protein. Plant-produced recombinant LipA is active towards p-nitrophenol esters of various carbon chain lengths with peak activity on medium-chain fatty acid (C8). The enzyme is also highly active on xylose tetra-acetate and oat spelt xylan. These results suggests that LipA is a novel lipolytic enzyme that possesses both lipase and acetylxylan esterase activity. We determined that LipA is a glycoprotein with pH and temperature optima at 8.0 and 40°C, respectively. Conclusion Besides being the first heterologous expression and characterization of a gene coding for a lipase from A. alcalophilum, this report shows that LipA is very versatile exhibiting both acetylxylan esterase and lipase activities potentially useful for diverse industry sectors, and that tobacco is a suitable bioreactor for producing fungal proteins. PMID:23915965

  13. Enhancing denitrification using a carbon supplement generated from the wet oxidation of waste activated sludge.

    PubMed

    Strong, P J; McDonald, B; Gapes, D J

    2011-05-01

    This study compared the effect of four pure carbon supplements on biological denitrification to a liquor derived as a by-product from the wet oxidation (WO) of waste activated sludge. Sequencing batch reactors were used to acclimate sludge biomass, which was used in batch assays. Acetate, WO liquor and ethanol-supplementation generated the fastest denitrification rates. Acetate and WO liquor were efficiently utilised by all acclimated biomass types, while poor rates were achieved with methanol and formate. When comparing an inoculum from an ethanol-supplemented and non-supplemented wastewater treatment plant (WWTP), the ethanol-acclimated sludge obtained superior denitrification rates when supplemented with ethanol. Similarly high nitrate removal rates were achieved with both sludge types with acetate and WO liquor supplementation, indicating that WO liquors could achieve excellent rates of nitrate removal. The performance of the WO liquor was attributed to the variety of organic carbon substrates (particularly acetic acid) present within the liquor. PMID:21196117

  14. Microbial lipids and stable foam formation in the activated sludge process.

    PubMed

    Goddard, A J; Forster, C F

    1991-01-01

    The presence of fats and oils in sewage has been related to the formation of stable foams in activated sludge treatment systems. Foam forming microbes can utilise and, in some cases, store lipid substrates. Since surface lipids would confer the hydrophobicity necessary for flotation on the sludge biomass, the extractable lipids in foaming and non-foaming biomass samples were examined. Both pure mono-cultures and sludge samples were used. The results showed that, whilst there were some differences in the lipid profiles of the mono-cultures, the different sludge types did not show any significant pattern or variation which could be used as a lipid-based explanation for foam formation. PMID:1907713

  15. Influence of different anoxic time exposures on active biomass, protozoa and filamentous bacteria in activated sludge.

    PubMed

    Rodriguez-Perez, S; Fermoso, F G; Arnaiz, C

    2016-01-01

    Medium-sized wastewater treatment plants are considered too small to implement anaerobic digestion technologies and too large for extensive treatments. A promising option as a sewage sludge reduction method is the inclusion of anoxic time exposures. In the present study, three different anoxic time exposures of 12, 6 and 4 hours have been studied to reduce sewage sludge production. The best anoxic time exposure was observed under anoxic/oxic cycles of 6 hours, which reduced 29.63% of the biomass production compared with the oxic control conditions. The sludge under different anoxic time exposures, even with a lower active biomass concentration than the oxic control conditions, showed a much higher metabolic activity than the oxic control conditions. Microbiological results suggested that both protozoa density and abundance of filamentous bacteria decrease under anoxic time exposures compared to oxic control conditions. The anoxic time exposures 6/6 showed the highest reduction in both protozoa density, 37.5%, and abundance of filamentous bacteria, 41.1%, in comparison to the oxic control conditions. The groups of crawling ciliates, carnivorous ciliates and filamentous bacteria were highly influenced by the anoxic time exposures. Protozoa density and abundance of filamentous bacteria have been shown as promising bioindicators of biomass production reduction. PMID:27508364

  16. Effect of powdered activated carbon on integrated submerged membrane bioreactor-nanofiltration process for wastewater reclamation.

    PubMed

    Woo, Yun Chul; Lee, Jeong Jun; Shim, Wang-Geun; Shon, Ho Kyong; Tijing, Leonard D; Yao, Minwei; Kim, Han-Seung

    2016-06-01

    The aim of this study was to determine the effect of powdered activated carbon (PAC) on the overall performance of a submerged membrane bioreactor (SMBR) system integrated with nanofiltration (NF) for wastewater reclamation. It was found that the trans-membrane pressure of SMBR increased continuously while that of the SMBR with PAC was more stable, mainly because water could still pass through the PACs and membrane even though foulants adhered on the PAC surface. The presence of PAC was able to mitigate fouling in SMBR as well as in NF. SMBR-NF with PAC obtained a higher flux of 8.1 LMH compared to that without PAC (6.6 LMH). In addition, better permeate quality was obtained with SMBR-NF integrated process added with PAC. The present results suggest that the addition of PAC in integrated SMBR-NF process could possibly lead to satisfying water quality and can be operated for a long-term duration. PMID:26879205

  17. Effect of pH on phosphorus, copper, and zinc elution from swine wastewater activated sludge.

    PubMed

    Waki, Miyoko; Yasuda, Tomoko; Fukumoto, Yasuyuki; Suzuki, Kazuyoshi

    2014-01-01

    With the goal of reducing the amounts of phosphorus (P), copper (Cu), and zinc (Zn) discharged from swine wastewater activated sludge treatment facilities, we studied the elution of these elements from activated sludge at various pH values. Sludge samples with neutral pH collected from three farms were incubated at pH values ranging from 3 to 10. The soluble concentrations of these elements changed dramatically with pH and were highest at pH 3. We assumed that P present in the sludge under neutral and alkaline conditions was in insoluble form bound up with magnesium (Mg) and calcium (Ca), because Ca and Mg also eluted from the sludge at low pH. To clarify forms of Zn and Cu in the sludge, we performed a sequential extraction analysis. Zinc in adsorbed, organically bound, and sulfide fractions made up a large proportion of the total Zn. Copper in organically bound, carbonate, and sulfide fractions made up a large proportion of the total Cu. The soluble P concentrations were lowest at pH 9 or 10 (11-36 mg/L), the soluble Zn concentrations were lowest at pH 8 or 9 (0.07-0.15 mg/L), and the soluble Cu concentrations were lowest at pH 6-9 (0.2 mg/L, the detection limit). PMID:25116486

  18. Detection of enteric viruses in activated sludge by feasible concentration methods

    PubMed Central

    Prado, Tatiana; Gaspar, Ana Maria Coimbra; Miagostovich, Marize Pereira

    2014-01-01

    Human enteric viruses are responsible to cause several diseases, including gastroenteritis and hepatitis, and can be present in high amounts in sewage sludge. This study compared virus recovery efficiency of two feasible concentration methods used for detecting human adenovirus (HAdV), rotavirus species A (RV-A), norovirus genogroup II (NoV GII) and hepatitis A virus (HAV) in sewage sludge from an activated sludge process. Twelve sewage sludge samples were collected bi-monthly from January to July, 2011. Ultracentrifugation was compared with a simplified protocol based on beef extract elution for recovering enteric viruses. Viruses were quantified by quantitative real-time PCR assays and virus recovery efficiency and limits of detection were determined. Methods showed mean recovery rates lower than 7.5%, presenting critical limits of detection (higher than 102 – 103 genome copies - GC L−1 for all viruses analyzed). Nevertheless, HAdV were detected in 90% of the analyzed sewage sludge samples (range: 1.8 × 104 to 1.1 × 105 GC L−1), followed by RV-A and NoV (both in 50%) and HAV (8%). Results suggesting that activated sludge is contaminated with high viral loads and HAdV are widely disseminated in these samples. The low virus recovery rates achieved, especially for HAV, indicate that other feasible concentration methods could be developed to improve virus recovery efficiency in these environmental matrices. PMID:24948954

  19. Bioaugmentation as a Tool To Protect the Structure and Function of an Activated-Sludge Microbial Community against a 3-Chloroaniline Shock Load

    PubMed Central

    Boon, Nico; Top, Eva M.; Verstraete, Willy; Siciliano, Steven D.

    2003-01-01

    Bioaugmentation of bioreactors focuses on the removal of xenobiotics, with little attention typically paid to the recovery of disrupted reactor functions such as ammonium-nitrogen removal. Chloroanilines are widely used in industry as a precursor to a variety of products and are occasionally released into wastewater streams. This work evaluated the effects on activated-sludge reactor functions of a 3-chloroaniline (3-CA) pulse and bioaugmentation by inoculation with the 3-CA-degrading strain Comamonas testosteroni I2 gfp. Changes in functions such as nitrification, carbon removal, and sludge compaction were studied in relation to the sludge community structure, in particular the nitrifying populations. Denaturing gradient gel electrophoresis (DGGE), real-time PCR, and fluorescent in situ hybridization (FISH) were used to characterize and enumerate the ammonia-oxidizing microbial community immediately after a 3-CA shock load. Two days after the 3-CA shock, ammonium accumulated, and the nitrification activity did not recover over a 12-day period in the nonbioaugmented reactors. In contrast, nitrification in the bioaugmented reactor started to recover on day 4. The DGGE patterns and the FISH and real-time PCR data showed that the ammonia-oxidizing microbial community of the bioaugmented reactor recovered in structure, activity, and abundance, while the number of ribosomes of the ammonia oxidizers in the nonbioaugmented reactor decreased drastically and the community composition changed and did not recover. The settleability of the activated sludge was negatively influenced by the 3-CA addition, with the sludge volume index increasing by a factor of 2.3. Two days after the 3-CA shock in the nonbioaugmented reactor, chemical oxygen demand (COD) removal efficiency decreased by 36% but recovered fully by day 4. In contrast, in the bioaugmented reactor, no decrease of the COD removal efficiency was observed. This study demonstrates that bioaugmentation of wastewater

  20. A comparative adsorption study: 17β-estradiol onto aerobic granular sludge and activated sludge.

    PubMed

    Zheng, Xiao-ying; He, Yu-jie; Chen, Wei; Wang, Ming-yang; Cao, Su-lan; Ni, Ming; Chen, Yu

    2016-01-01

    Adsorption plays a significant role in removing hydrophobic 17β-estradiol (E2) from wastewater. Batch experiments were conducted to compare the adsorption of E2 onto activated aerobic granular sludge (AGS) and activated sludge (AS), and features evaluated included the adsorption kinetics, thermodynamics, and influence of other environmental factors. By using a non-chemical wet-heat technique, both AGS and AS were treated to inactivated status. Then, after loading E2, the adsorption equilibrium capacity of the AGS was found to be greater than that of the AS at the same initial concentration of E2. Moreover, both the adsorption processes corresponded to a pseudo-second-order kinetic model; the adsorption rate constant of AGS was found to be higher and the half-adsorption time was shorter than that of AS. Next, evaluations of adsorption isotherms and thermodynamics indicated that the adsorption process was mainly a physical process. Lower temperatures facilitated a higher equilibrium adsorption capacity. However, the adsorption binding sites of AGS were distributed more uniformly at higher temperature, in contrast to the distribution found for AS. Finally, acidic conditions and an appropriate ionic strength (0.4 mol/L) were found to be particularly conducive to the adsorption process. Overall, the results showed that AGS has the potential to adsorb E2 with significant efficiency, thereby offering a new and more efficient means of treating E2 and trace oestrogens in wastewater. PMID:26209151

  1. Effect of acetic acid on lipid accumulation by glucose-fed activated sludge cultures

    SciTech Connect

    Mondala, Andro; Hernandez, Rafael; French, Todd; McFarland, Linda; Sparks, Darrell; Holmes, William; Haque, Monica

    2012-01-01

    The effect of acetic acid, a lignocellulose hydrolysis by-product, on lipid accumulation by activated sludge cultures grown on glucose was investigated. This was done to assess the possible application of lignocellulose as low-cost and renewable fermentation substrates for biofuel feedstock production. Results: Biomass yield was reduced by around 54% at a 2 g L -1 acetic acid dosage but was increased by around 18% at 10 g L -1 acetic acid dosage relative to the control run. The final gravimetric lipid contents at 2 and 10 g L -1 acetic acid levels were 12.5 + 0.7% and 8.8 + 3.2% w/w, respectively, which were lower than the control (17.8 + 2.8% w/w). However, biodiesel yields from activated sludge grown with acetic acid (5.6 + 0.6% w/w for 2 g L -1 acetic acid and 4.2 + 3.0% w/w for 10 g L -1 acetic acid) were higher than in raw activated sludge (1-2% w/w). The fatty acid profiles of the accumulated lipids were similar with conventional plant oil biodiesel feedstocks. Conclusions: Acetic acid enhanced biomass production by activated sludge at high levels but reduced lipid production. Further studies are needed to enhance acetic acid utilization by activated sludge microorganisms for lipid biosynthesis.

  2. MiDAS: the field guide to the microbes of activated sludge

    PubMed Central

    McIlroy, Simon Jon; Saunders, Aaron Marc; Albertsen, Mads; Nierychlo, Marta; McIlroy, Bianca; Hansen, Aviaja Anna; Karst, Søren Michael; Nielsen, Jeppe Lund; Nielsen, Per Halkjær

    2015-01-01

    The Microbial Database for Activated Sludge (MiDAS) field guide is a freely available online resource linking the identity of abundant and process critical microorganisms in activated sludge wastewater treatment systems to available data related to their functional importance. Phenotypic properties of some of these genera are described, but most are known only from sequence data. The MiDAS taxonomy is a manual curation of the SILVA taxonomy that proposes a name for all genus-level taxa observed to be abundant by large-scale 16 S rRNA gene amplicon sequencing of full-scale activated sludge communities. The taxonomy can be used to classify unknown sequences, and the online MiDAS field guide links the identity to the available information about their morphology, diversity, physiology and distribution. The use of a common taxonomy across the field will provide a solid foundation for the study of microbial ecology of the activated sludge process and related treatment processes. The online MiDAS field guide is a collaborative workspace intended to facilitate a better understanding of the ecology of activated sludge and related treatment processes—knowledge that will be an invaluable resource for the optimal design and operation of these systems. Database URL: http://www.midasfieldguide.org PMID:26120139

  3. [Rapid method to extract high-quality RNA from activated sludge].

    PubMed

    Jin, Min; Zhao, Zu-Guo; Qiu, Zhi-Gang; Wang, Jing-Feng; Chen, Zhao-Li; Shen, Zhi-Qiang; Li, Chao; Wang, Xin-Wei; Dong, Yan; Li, Jun-Wen

    2010-01-01

    An effective and fast RNA isolation method of activated sludge was established and five different methods were compared based on RNA yield, purity, integrity, RT-PCR amplification of 16S rRNA genes and subsequent terminal restriction fragment length polymorphism (T-RFLP) analysis. That is, the precipitated activated sludge was washed with TENP and PBS buffer, followed by using lysozyme and TRIzol to direct lysis of microbial cells, chloroform to remove protein and most of the DNA from bacterial lysate, isopropanol to precipitate nucleic acid and DNase I to hydrolyze residual DNA. To further purify RNA, RNA purifying column was utilized. The results demonstrated that the extraction method, with the aid of TRIzol and RNA purification kit, can effectively extract high-quality RNA. It not only means low degradability and high quantity, purity and diversity, but also the genes of 16S rRNA and amoA can be amplified by RT-PCR. Compared with other methods, it showed great advantage of low cost and high efficiency and can be applied to RNA extraction of activated sludge in a large number. Furthermore, T-RFLP results indicated that the community composition as well as the abundance of individual members was affected by the kind of RNA extraction methods. This work established a rapid and effective method to extract high-quality RNA from activated sludge and would show great potential for monitoring microbial changes and studying metabolism and community array of activated sludge. PMID:20329549

  4. MiDAS: the field guide to the microbes of activated sludge.

    PubMed

    McIlroy, Simon Jon; Saunders, Aaron Marc; Albertsen, Mads; Nierychlo, Marta; McIlroy, Bianca; Hansen, Aviaja Anna; Karst, Søren Michael; Nielsen, Jeppe Lund; Nielsen, Per Halkjær

    2015-01-01

    The Microbial Database for Activated Sludge (MiDAS) field guide is a freely available online resource linking the identity of abundant and process critical microorganisms in activated sludge wastewater treatment systems to available data related to their functional importance. Phenotypic properties of some of these genera are described, but most are known only from sequence data. The MiDAS taxonomy is a manual curation of the SILVA taxonomy that proposes a name for all genus-level taxa observed to be abundant by large-scale 16 S rRNA gene amplicon sequencing of full-scale activated sludge communities. The taxonomy can be used to classify unknown sequences, and the online MiDAS field guide links the identity to the available information about their morphology, diversity, physiology and distribution. The use of a common taxonomy across the field will provide a solid foundation for the study of microbial ecology of the activated sludge process and related treatment processes. The online MiDAS field guide is a collaborative workspace intended to facilitate a better understanding of the ecology of activated sludge and related treatment processes--knowledge that will be an invaluable resource for the optimal design and operation of these systems. PMID:26120139

  5. Removal of endocrine-disrupting chemicals in activated sludge treatment works.

    PubMed

    Johnson, A C; Sumpter, J P

    2001-12-15

    The release of endocrine-disrupting chemicals into the aquatic environment has raised the awareness of the central role played by sewage treatment in lowland water quality. This review focuses on the activated sludge process, which is commonly used to treat sewage in large towns and cities and which successfully removes the bulk of the organic compounds that enter the works. However, not all compounds are completely broken down or converted to biomass. For example, the estrogenic alkylphenols and steroid estrogens found in effluent are the breakdown products of incomplete breakdown of their respective parent compounds. Batch microcosm studies have indicated that estrone, ethinylestradiol, and alkylphenols will not be completely eliminated in activated sludge over typical treatment times. Field data suggest that the activated sludge treatment process can consistently remove over 85% of estradiol, estriol, and ethinylestradiol. The removal performance for estrone appears to be less and is more variable. Because of its relatively high hydrophobicity, the accumulation of alkylphenol in sludge has been observed. Although it has not been examined, accumulation of ethinylestradiol in sludge is a possibility due to its recalcitrance and hydrophobicity. A comparison between the concentrations of some of the major endocrine-active chemicals in effluents and their biological potencies has been made, to direct attention to the chemicals of most concern. While water purification techniques such as UV or activated charcoal could significantly remove these microorganic contaminants, the high costs involved suggest that research into the potential for treatment optimization should receive more attention. PMID:11775141

  6. Study of kinetics of degradation of cyclohexane carboxylic acid by acclimated activated sludge.

    PubMed

    Wang, Chunhua; Shi, Shuian; Chen, Hongyan

    2016-01-01

    Activated sludge contains complex microorganisms, which are highly effective biodegrading agents. In this study, the kinetics of biodegradation of cyclohexane carboxylic acid (CHCA) by an acclimated aerobic activated sludge were investigated. The results showed that after 180 days of acclimation, the activated sludge could steadily degrade >90% of the CHCA in 120 h. The degradation of CHCA by the acclimated activated sludge could be modeled using a first-order kinetics equation. The equations for the degradation kinetics for different initial CHCA concentrations were also obtained. The kinetics constant, kd, decreased with an increase in the CHCA concentration, indicating that, at high concentrations, CHCA had an inhibiting effect on the microorganisms in the activated sludge. The effects of pH on the degradation kinetics of CHCA were also investigated. The results showed that a pH of 10 afforded the highest degradation rate, indicating that basic conditions significantly promoted the degradation of CHCA. Moreover, it was found that the degradation efficiency for CHCA increased with an increase in temperature and concentration of dissolved oxygen under the experimental conditions. PMID:27191578

  7. Biocrude production by activated sludge microbial cultures using pulp and paper wastewaters as fermentation substrate.

    PubMed

    Upadhyaya, Kamal Lamichhane; Mondala, Andro; Hernandez, Rafael; French, Todd; Green, Magan; McFarland, Linda; Holmes, William

    2013-01-01

    Municipal wastewater activated sludge contains a mixed microbial community, which can be manipulated to produce biocrude, a lipid feedstock for biodiesel production. In this study, the potential of biocrude production by activated sludge microorganisms grown in three different types of pulp and paper mill wastewaters was investigated. A 20% (v/v) activated sludge was inoculated into pulp and paper wastewater, supplemented with glucose (60 g/L) and nutrients (nitrogen and phosphorus) to obtain a high carbon to nitrogen ratio (70:1). The culture was incubated aerobically for seven days. The results showed that the activated sludge microorganisms were able to grow and accumulate lipids when cultivated in amended wastewaters. Microorganisms growing in anaerobic settling pond effluent water showed the highest lipid accumulation of up to 40.6% cell dry weight (CDW) after five days of cultivation compared with pulp wash wastewater (PuWW) (11.7% CDW) and mixed wastewater (MWW) (8.2% CDW) after seven days of cultivation. The lipids mostly contained C16-C18 fatty acids groups with oleic acid and palmitic acid being the dominant fatty acids. The maximum biodiesel yield was about 6-8% CDW for all the wastewaters. The results showed the potential of utilizing pulp and paper mill effluents and other waste streams, such as activated sludge for the sustainable production of lipids for biofuel production. PMID:24350471

  8. Effect of polyhydroxyalkanoates on dark fermentative hydrogen production from waste activated sludge.

    PubMed

    Wang, Dongbo; Zeng, Guangming; Chen, Yinguang; Li, Xiaoming

    2015-04-15

    Polyhydroxyalkanoates (PHA), an intracellular energy and carbon storage polymer, can be accumulated in activated sludge in substantial quantities under wastewater dynamic treatment (i.e., substrate feast-famine) conditions. However, its influence on hydrogen production has never been investigated before. This study therefore evaluated the influences of PHA level and composition in waste activated sludge (WAS) on hydrogen production. The results showed that with the increase of sludge PHA content from 25 to 178 mg per gram volatile suspended solids (VSS) hydrogen production from WAS alkaline anaerobic fermentation increased from 26.5 to 58.7 mL/g VSS. The composition of PHA was also found to affect hydrogen production. When the dominant composition shifted from polyhydroxybutyrate (PHB) to polyhydroxyvalerate (PHV), the amount of generated hydrogen decreased from 51.2 to 41.1 mL/g VSS even under the same PHA level (around 130 mg/g VSS). The mechanism studies exhibited that the increased PHA content accelerated both the cell solubilization and the hydrolysis process of solubilized substrates. Compared with the PHB-dominant sludge, the increased PHV fraction not only slowed the hydrolysis process but also caused more propionic acid production, with less theoretical hydrogen generation in this fermentation type. It was also found that the increased PHA content enhanced the soluble protein conversion of non-PHA biomass. Further investigations with enzyme analyses showed that both the key hydrolytic enzyme activities and hydrogen-forming enzyme activities were in the sequence of the PHB-dominant sludge > the PHV-dominant sludge > the low PHA sludge, which was in accord with the observed order of hydrogen yield. PMID:25697693

  9. Organic matter extracted from activated sludge with ammonium hydroxide and its characterization.

    PubMed

    Wei, Liangliang; Wang, Kun; Zhao, Qingliang; Jiang, Junqiu; Xie, Chunmei; Qiu, Wei

    2010-01-01

    In order to characterize the organic properties of waste activated sludge in a wastewater treatment plant, organic matter within sludge was extracted with NH3.H20 preferentially, and subsequently fractionated into five fractions using XAD-8/XAD-4 resins. Up to a 63.8%-71.1% of organic matter within the sludge could be efficiently extracted by NH3.H2O. Fractionation results showed that hydrophobic acid and hydrophilic fraction were two main components among the sludge organic matter (accounting for 32.2% and 48.0% of the bulk organic matter, respectively), whereas transphilic acid, hydrophobic neutral and transphilic neutral were quite low (accounting for 9.2%, 5.8% and 4.8%, respectively). Despite that the extractant of NH3.H2O showed a relatively higher extraction efficiency of the aromatic components, the relatively low aromaticity of the organic fractions implied that those non-aromatic components could also be effectively extracted, especially for neutral and hydrophilic fractions. In addition, acidic fractions contained more aromatic humic-like components, whereas the neutral fractions had a greater content of aromatic proteins and soluble microbial byproduct-like components. Extraction of sludge organics with NH3.H2O and subsequential fractionation using XAD resins could be a novel method for further characterization of sludge organics. PMID:20608497

  10. Chitosan use in chemical conditioning for dewatering municipal-activated sludge.

    PubMed

    Zemmouri, H; Mameri, N; Lounici, H

    2015-01-01

    This work aims to evaluate the potential use of chitosan as an eco-friendly flocculant in chemical conditioning of municipal-activated sludge. Chitosan effectiveness was compared with synthetic cationic polyelectrolyte Sedipur CF802 (Sed CF802) and ferric chloride (FeCl₃). In this context, raw sludge samples from Beni-Messous wastewater treatment plant (WWTP) were tested. The classic jar test method was used to condition sludge samples. Capillary suction time (CST), specific resistance to filtration (SRF), cakes dry solid content and filtrate turbidity were analyzed to determine filterability, dewatering capacity of conditioned sludge and the optimum dose of each conditioner. Data exhibit that chitosan, FeCl₃and Sed CF802 improve sludge dewatering. Optimum dosages of chitosan, Sed CF802 and FeCl₃allowing CST values of 6, 5 and 9 s, were found, respectively, between 2-3, 1.5-3 and 6 kg/t ds. Both polymers have shown faster water removal with more permeable sludge. SRF values were 0.634 × 10¹², 0.932 × 10¹² and 2 × 10¹² m/kg for Sed CF802, chitosan and FeCl₃respectively. A reduction of 94.68 and 87.85% of the filtrate turbidity was obtained with optimal dosage of chitosan and Sed CF802, respectively. In contrast, 54.18% of turbidity abatement has been obtained using optimal dosage of FeCl₃. PMID:25812088

  11. The Impact of Oxone on Disintegration and Dewaterability of Waste Activated Sludge.

    PubMed

    Wacławek, Stanisław; Grübel, Klaudiusz; Chłąd, Zuzanna; Dudziak, Mariusz; Černík, Miroslav

    2016-02-01

    Biochemical parameters such as soluble chemical oxygen demand (SCOD), phosphate, ammonium nitrogen and proteins are often used to characterize the efficiency of disintegration of waste activated sludge (WAS) flocs and microorganism cells. In this study, the chemical disintegration using peroxymonosulfate (MPS, Oxone) and thermally activated MPS, were evaluated for the destruction of WAS. Our study was conducted for chemical disintegration of WAS by MPS in doses between 84.7 - 847.5 mg/g(TS) activated by temperatures of 50, 70 and 90 °C over 30 minutes. The application of these methods causes an increase in the soluble COD value and protein concentration in the supernatant. Also, they positively influence the sludge volume index (SVI) which decreased from 89.8 to 17.2 ml/g. Our research work confirmed that the application of thermally activated MPS may become a new effective way of improving sewage treatment and sewage sludge processing. PMID:26803102

  12. Foaming in membrane bioreactors: identification of the causes.

    PubMed

    Di Bella, Gaetano; Torregrossa, Michele

    2013-10-15

    Membrane bioreactors (MBRs) represent by now a well established alternative for wastewater treatment. Their increasing development is undoubtedly related to the several advantages that such technology is able to guarantee. Nevertheless, this technology is not exempt from operational problems; among them the foaming still represents an "open challenge" of the MBR field, due to the high complexity of phenomenon. Unfortunately, very little work has been done on the foaming in MBRs and further studies are required. Actually, there is not a distinct difference between conventional activated system and MBR: the main difference is that the MBR plants can retain most Extracellular Polymeric Substances (EPSs) in the bioreactor. For these reason, unlike conventional activated sludge systems, MBRs have experienced foaming in the absence of foam-forming micro-organisms. Nevertheless, the actual mechanisms of EPS production and the role of bacteria in producing foam in activated sludge in MBRs are still unclear. In this paper, the authors investigated the roles of EPS and foam-forming filamentous bacteria by analyzing samples from different pilot plants using MBRs. In particular, in order to define the macroscopic features and the role of EPS and filamentous bacteria, a Modified Scum Index (MSI) test was applied and proposed. Based on the MSI and the foam power test, the causes of biological foaming were identified in terms of the potential for foaming, the quality and the quantity of the foam. The results indicated that the MBR foaming was influenced significantly by the concentration of bound EPSs in the sludge. In addition, the quantity and stability of MBR scum increased when both bound EPSs and foam-forming filamentous bacteria were present in the activated sludge. PMID:23792916

  13. Rhodoligotrophos jinshengii sp. nov., isolated from activated sludge.

    PubMed

    Deng, Shi-Kai; Chen, Guo-Qiang; Chen, Qing; Cai, Shu; Yao, Li; He, Jian; Li, Shun-Peng

    2014-09-01

    A Gram-stain-negative, non-spore-forming, non-motile, ovoid, aerobic bacterial strain, designated BUT-3(T), was isolated from activated sludge from the wastewater treatment facility of a herbicide-manufacturing plant in Kunshan city, Jiangsu province, PR China. Strain BUT-3(T) grew between 15 and 40 °C, with optimum growth at 30 °C. The pH range for growth was between 5.0 and 10.0 (optimum pH 7.0). The range of NaCl concentrations for growth of strain BUT-3(T) was 0-7.0 % (w/v), with an optimum of 1.5-3.0 % (w/v). A phylogenetic tree based on 16S rRNA gene sequence analysis showed that strain BUT-3(T) clustered closely with Rhodoligotrophos appendicifer 120-1(T) (98.32 % similarity), with a bootstrap confidence level of 100 %. The major fatty acids (>5 % of total fatty acids) were C19 : 0 cyclo ω8c, C18 : 1ω7c, C16 : 0, anteiso-C15 : 0 and iso-C15 : 0. Strain BUT-3(T) contained ubiquinone Q-10 as the predominant respiratory quinone. The polar lipid profile comprised diphosphatidylglycerol, phosphatidylglycerol, phosphatidylethanolamine, phosphatidylcholine, three unidentified aminolipids (AL1-3), two unknown phospholipids (PL1, 5), four unidentified glycolipids (GL1-4) and two unknown lipids (L1, 2). The G+C content of the genomic DNA was 67.7 mol%. The DNA-DNA relatedness between BUT-3(T) and R. appendicifer 120-1(T) was 44.1±0.6 %. Based on the polyphasic taxonomic data, strain BUT-3(T) should be classified as a representative of a novel species of the genus Rhodoligotrophos, for which the name Rhodoligotrophos jinshengii sp. nov. is proposed. The type strain is BUT-3(T) ( = CCTCC AB2013083(T) = KACC 17220(T)). PMID:25002364

  14. Development of Sulfidogenic Sludge from Marine Sediments and Trichloroethylene Reduction in an Upflow Anaerobic Sludge Blanket Reactor.

    PubMed

    Guerrero-Barajas, Claudia; Ordaz, Alberto; García-Solares, Selene Montserrat; Garibay-Orijel, Claudio; Bastida-González, Fernando; Zárate-Segura, Paola Berenice

    2015-01-01

    The importance of microbial sulfate reduction relies on the various applications that it offers in environmental biotechnology. Engineered sulfate reduction is used in industrial wastewater treatment to remove large concentrations of sulfate along with the chemical oxygen demand (COD) and heavy metals. The most common approach to the process is with anaerobic bioreactors in which sulfidogenic sludge is obtained through adaptation of predominantly methanogenic granular sludge to sulfidogenesis. This process may take a long time and does not always eliminate the competition for substrate due to the presence of methanogens in the sludge. In this work, we propose a novel approach to obtain sulfidogenic sludge in which hydrothermal vents sediments are the original source of microorganisms. The microbial community developed in the presence of sulfate and volatile fatty acids is wide enough to sustain sulfate reduction over a long period of time without exhibiting inhibition due to sulfide. This protocol describes the procedure to generate the sludge from the sediments in an upflow anaerobic sludge blanket (UASB) type of reactor. Furthermore, the protocol presents the procedure to demonstrate the capability of the sludge to remove by reductive dechlorination a model of a highly toxic organic pollutant such as trichloroethylene (TCE). The protocol is divided in three stages: (1) the formation of the sludge and the determination of its sulfate reducing activity in the UASB, (2) the experiment to remove the TCE by the sludge, and (3) the identification of microorganisms in the sludge after the TCE reduction. Although in this case the sediments were taken from a site located in Mexico, the generation of a sulfidogenic sludge by using this procedure may work if a different source of sediments is taken since marine sediments are a natural pool of microorganisms that may be enriched in sulfate reducing bacteria. PMID:26555802

  15. Effect of magnetic nanoparticles on the performance of activated sludge treatment system.

    PubMed

    Ni, Shou-Qing; Ni, Jianyuan; Yang, Ning; Wang, Juan

    2013-09-01

    Both short-term and long-term exposure experiments were carried out to investigate the influence of magnetic nanoparticles (NPs) on activated sludge. The short-term presence of 50-200 mg/L of NPs decreased total nitrogen (TN) removal efficiencies, resulted from the acute toxicity of a shock load of NPs. However, long-term exposure of 50 mg/L magnetic NPs were observed to significantly improve TN removal efficiency, partially due to the self-repair function of activated sludge and magnetic-induced bio-effect. Sludge properties and extracellular polymer substrates secretion were affected. Additional investigations with enzyme and FISH assays indicated that short-term exposure of 50 mg/L magnetic NPs led to the abatement of nitrifying bacteria. However, the activities of the enzyme nitrite oxidoreductase and key denitrifying enzymes were increased after long-term exposure. PMID:23835260

  16. Use of metagenomic approaches to isolate lipolytic genes from activated sludge.

    PubMed

    Liaw, Ren-Bao; Cheng, Mei-Ping; Wu, Ming-Che; Lee, Chia-Yin

    2010-11-01

    The aims of this study were to access the bacterial diversity and isolate lipolytic genes using the metagenomic approach in activated sludge of a swine wastewater treatment facility. On the basis of BLASTN analysis of 16S rRNA gene clones, most of these communities (90%) were of uncultivated bacteria. The metagenomic library was constructed using a plasmid vector and DNA extracted directly from activated sludge samples. The average insert size was approximately 5.1 kb. A total of 12 unique and lipolytic clones were obtained using the tributyrin plate assay. The rate of discovering a lipolytic clone in this study was as high as 0.31%. Molecular analysis revealed that most of the 16 putative lipolytic enzymes showed 28-55% identity with non-redundant protein sequences in the database. Briefly, this study demonstrates that activated sludge is an ideal bioresource for isolating new lipolytic enzymes. PMID:20639117

  17. Effect of a static magnetic field on formaldehyde biodegradation in wastewater by activated sludge.

    PubMed

    Łebkowska, Maria; Rutkowska-Narożniak, Anna; Pajor, Elżbieta; Pochanke, Zbigniew

    2011-10-01

    The aim of this study was to determine the impact of a static magnetic field (MF) of 7 mT on formaldehyde (FA) biodegradation by activated sludge in synthetic wastewater. The MF had a positive effect on activated sludge biomass growth and dehydrogenase activity. The influence of the MF on the degradation process was observed with a FA concentration of 2400-2880 mg/l. Decreases in FA concentration and chemical oxygen demand (COD) were greater, by 30% and 26% respectively, than those in the control sample. At initial FA concentrations in raw wastewater of 2400 and 2880 mg/l, a decrease in the wastewater biodegradation efficiency was observed. This resulted in an increase of the ecotoxicity of the effluent to Daphnia magna. The value of the sludge biotic index (SBI) was dependent on the FA concentration in raw wastewater and the induction of the MF. PMID:21824771

  18. Virus elimination in activated sludge systems: from batch tests to mathematical modeling.

    PubMed

    Haun, Emma; Ulbricht, Katharina; Nogueira, Regina; Rosenwinkel, Karl-Heinz

    2014-01-01

    A virus tool based on Activated Sludge Model No. 3 for modeling virus elimination in activated sludge systems was developed and calibrated with the results from laboratory-scale batch tests and from measurements in a municipal wastewater treatment plant (WWTP). The somatic coliphages were used as an indicator for human pathogenic enteric viruses. The extended model was used to simulate the virus concentration in batch tests and in a municipal full-scale WWTP under steady-state and dynamic conditions. The experimental and modeling results suggest that both adsorption and inactivation processes, modeled as reversible first-order reactions, contribute to virus elimination in activated sludge systems. The model should be a useful tool to estimate the number of viruses entering water bodies from the discharge of treated effluents. PMID:25259502

  19. Effect of Elevated Salt Concentrations on the Aerobic Granular Sludge Process: Linking Microbial Activity with Microbial Community Structure▿

    PubMed Central

    Bassin, J. P.; Pronk, M.; Muyzer, G.; Kleerebezem, R.; Dezotti, M.; van Loosdrecht, M. C. M.

    2011-01-01

    The long- and short-term effects of salt on biological nitrogen and phosphorus removal processes were studied in an aerobic granular sludge reactor. The microbial community structure was investigated by PCR-denaturing gradient gel electrophoresis (DGGE) on 16S rRNA and amoA genes. PCR products obtained from genomic DNA and from rRNA after reverse transcription were compared to determine the presence of bacteria as well as the metabolically active fraction of bacteria. Fluorescence in situ hybridization (FISH) was used to validate the PCR-based results and to quantify the dominant bacterial populations. The results demonstrated that ammonium removal efficiency was not affected by salt concentrations up to 33 g/liter NaCl. Conversely, a high accumulation of nitrite was observed above 22 g/liter NaCl, which coincided with the disappearance of Nitrospira sp. Phosphorus removal was severely affected by gradual salt increase. No P release or uptake was observed at steady-state operation at 33 g/liter NaCl, exactly when the polyphosphate-accumulating organisms (PAOs), “Candidatus Accumulibacter phosphatis” bacteria, were no longer detected by PCR-DGGE or FISH. Batch experiments confirmed that P removal still could occur at 30 g/liter NaCl, but the long exposure of the biomass to this salinity level was detrimental for PAOs, which were outcompeted by glycogen-accumulating organisms (GAOs) in the bioreactor. GAOs became the dominant microorganisms at increasing salt concentrations, especially at 33 g/liter NaCl. In the comparative analysis of the diversity (DNA-derived pattern) and the activity (cDNA-derived pattern) of the microbial population, the highly metabolically active microorganisms were observed to be those related to ammonia (Nitrosomonas sp.) and phosphate removal (“Candidatus Accumulibacter”). PMID:21926194

  20. Fatty acids of lipid fractions in extracellular polymeric substances of activated sludge flocs.

    PubMed

    Conrad, Arnaud; Suutari, Merja Kontro; Keinänen, Minna M; Cadoret, Aurore; Faure, Pierre; Mansuy-Huault, Laurence; Block, Jean-Claude

    2003-10-01

    Phospholipid (PL), glycolipid (GL), and neutral lipid (NL) FA, and the lipopolysaccharide 2- and 3-hydroxy (LPS 2-OH and 3-OH) FA of activated sludges and extracted extracellular polymeric substances (EPS) were determined on samples collected from two wastewater treatment plants. EPS extracted from sludges by means of sonication and cation exchange contained proteins (43.4%), humic-like substances (11.5%), nucleic acids (10.9%), carbohydrates (9.9%), and lipid-bound FA (1.8%). The lipids associated with EPS were composed of GL, PL, NL, and LPS acids in proportions of 61, 21, 16, and 2%, respectively. The profiles of lipid-bound FA in activated sludges and EPS were similar (around 85 separate FA were identified). The FA signatures observed can be attributed to the likely presence of yeasts, fungi, sulfate-reducing bacteria, gram-positive and gram-negative bacteria, and, in lesser quantities, mycobacteria. Comparison of data from the dates of sampling (January and September) showed that there were more unsaturated PLFA in the EPS extracted from the activated sludges sampled in January. This observation could be partly related to microorganism adaptation to temperature variations. The comparison between two wastewater treatment plants showed that the FA profiles were similar, although differences in microbial community structure were also seen. Most of the FA in sludges had an even number of carbons. PMID:14669975

  1. Micropollutant removal by attached and suspended growth in a hybrid biofilm-activated sludge process.

    PubMed

    Falås, P; Longrée, P; la Cour Jansen, J; Siegrist, H; Hollender, J; Joss, A

    2013-09-01

    Removal of organic micropollutants in a hybrid biofilm-activated sludge process was investigated through batch experiments, modeling, and full-scale measurements. Batch experiments with carriers and activated sludge from the same full-scale reactor were performed to assess the micropollutant removal rates of the carrier biofilm under oxic conditions and the sludge under oxic and anoxic conditions. Clear differences in the micropollutant removal kinetics of the attached and suspended growth were demonstrated, often with considerably higher removal rates for the biofilm compared to the sludge. For several micropollutants, the removal rates were also affected by the redox conditions, i.e. oxic and anoxic. Removal rates obtained from the batch experiments were used to model the micropollutant removal in the full-scale process. The results from the model and plant measurements showed that the removal efficiency of the process can be predicted with acceptable accuracy (± 25%) for most of the modeled micropollutants. Furthermore, the model estimations indicate that the attached growth in hybrid biofilm-activated sludge processes can contribute significantly to the removal of individual compounds, such as diclofenac. PMID:23764599

  2. Enhancing anaerobic digestion of waste activated sludge by pretreatment: effect of volatile to total solids.

    PubMed

    Wang, Xiao; Duan, Xu; Chen, Jianguang; Fang, Kuo; Feng, Leiyu; Yan, Yuanyuan; Zhou, Qi

    2016-06-01

    In this study the effect of volatile to total solids (VS/TS) on anaerobic digestion of waste activated sludge (WAS) pretreated by alkaline, thermal and thermal-alkaline strategies was studied. Experimental results showed that the production of methane from sludge was increased with VS/TS. When anaerobic digesters were fed with sludge pretreated by the thermal-alkaline method, the average methane yield was improved from 2.8 L/d at VS/TS 0.35 to 4.7 L/d at VS/TS 0.56. Also, the efficiency of VS reduction during sludge anaerobic digestion varied between 18.9% and 45.6%, and increased gradually with VS/TS. Mechanism investigation of VS/TS on WAS anaerobic digestion suggested that the general activities of anaerobic microorganisms, activities of key enzymes related to sludge hydrolysis, acidification and methanogenesis, and the ratio of Archaea to Bacteria were all increased with VS/TS, showing good agreement with methane production. PMID:26698921

  3. [Comparative Metagenomics of BIOLAK and A2O Activated Sludge Based on Next-generation Sequencing Technology].

    PubMed

    Tian, Mei; Liu, Han-hu; Shen, Xin

    2016-02-15

    This is the first report of comparative metagenomic analyses of BIOLAK sludge and anaerobic/anoxic/oxic (A2O) sludge. In the BIOLAK and A2O sludge metagenomes, 47 and 51 phyla were identified respectively, more than the numbers of phyla identified in Australia EBPR (enhanced biological phosphorus removal), USA EBPR and Bibby sludge. All phyla found in the BIOLAK sludge were detected in the A2O sludge, but four phyla were exclusively found in the A20 sludge. The proportion of the phylum Ignavibacteriae in the A2O sludge was 2.0440%, which was 3.2 times as much as that in the BIOLAK sludge (0.6376%). Meanwhile, the proportion of the bacterial phylum Gemmatimonadetes in the BIOLAK sludge was 2.4673%, which was >17 times as much as that in the A2O sludge (0.1404%). The proportion of the bacterial phylum Chlamydiae in the BIOLAK metagenome (0.2192%) was >6 times higher than that in the A2O (0.0360%). Furthermore, 167 genera found in the A20 sludge were not detected in the BIOLAK sludge. And 50 genera found in the BIOLAK sludge were not detected in the A20 sludge. From the analyses of both the phylum and genus levels, there were huge differences between the two biological communities of A2O and BIOLAK sludge. However, the proportions of each group of functional genes associated with metabolism of nitrogen, phosphor, sulfur and aromatic compounds in BIOLAK were very similar to those in A2O sludge. Moreover, the rankings of all six KEGG (Kyoto Encyclopedia for Genes and Genomes) categories were identical in the two sludges. In addition, the analyses of functional classification and pathway related nitrogen metabolism showed that the abundant enzymes had identical ranking in the BIOLAK and A2O metagenomes. Therefore, comparative metagenomics of BIOLAK and A2O activated sludge indicated similar function assignments from the two different biological communities. PMID:27363155

  4. Microbial Activity In The Peerless Jenny King Sulfate Reducing Bioreactor System (Presentation)

    EPA Science Inventory

    The Peerless Jenny King treatment system is a series of four sulfate reducing bioreactor cells installed to treat acid mine drainage in the Upper Tenmile Creek Superfund Site located in the Rimini Mining District, near Helena MT. The system consists of a wetland pretreatment fol...

  5. Microbial Activity In The Peerless Jenny King Sulfate Reducing Bioreactors System

    EPA Science Inventory

    The Peerless Jenny King treatment system is a series of four sulfate reducing bioreactor cells installed to treat acid mine drainage in the Upper Tenmile Creek Superfund Site located in the Rimini Mining District, near Helena, MT. The system consists of a wetland pretreatment fo...

  6. NASA Classroom Bioreactor

    NASA Technical Reports Server (NTRS)

    Scully, Robert

    2004-01-01

    Exploration of space provides a compelling need for cell-based research into the basic mechanisms that underlie the profound changes that occur in terrestrial life that is transitioned to low gravity environments. Toward that end, NASA developed a rotating bioreactor in which cells are cultured while continuously suspended in a cylinder in which the culture medium rotates with the cylinder. The randomization of the gravity vector accomplished by the continuous rotation, in a low shear environment, provides an analog of microgravity. Because cultures grown in bioreactors develop structures and functions that are much closer to those exhibited by native tissue than can be achieved with traditional culture methods, bioreactors have contributed substantially to advancing research in the fields of cancer, diabetes, infectious disease modeling for vaccine production, drug efficacy, and tissue engineering. NASA has developed a Classroom Bioreactor (CB) that is built from parts that are easily obtained and assembled, user-friendly and versatile. It can be easily used in simple school settings to examine the effect cultures of seeds or cells. An educational brief provides assembly instructions and lesson plans that describes activities in science, math and technology that explore free fall, microgravity, orbits, bioreactors, structure-function relationships and the scientific method.

  7. Trace organics removal using three membrane bioreactor configurations: MBR, IFAS-MBR and MBMBR.

    PubMed

    de la Torre, T; Alonso, E; Santos, J L; Rodríguez, C; Gómez, M A; Malfeito, J J

    2015-01-01

    Seventeen pharmaceutically active compounds and 22 other trace organic pollutants were analysed regularly in the influent and permeate from a semi-real plant treating municipal wastewater. The plant was operated during 29 months with different configurations which basically differed in the type of biomass present in the system. These processes were the integrated fixed-film activated sludge membrane bioreactor (IFAS-MBR), which combined suspended and attached biomass, the moving bed membrane bioreactor (MBMBR) (only attached biomass) and the MBR (only suspended biomass). Moreover, removal rates were compared to those of the wastewater treatment plant (WWTP) operating nearby with conventional activated sludge treatment. Reverse osmosis (RO) was used after the pilot plant to improve removal rates. The highest elimination was found for the IFAS-MBR, especially for hormones (100% removal); this was attributed to the presence of biofilm, which may lead to different conditions (aerobic-anoxic-anaerobic) along its profile, which increases the degradation possibilities, and also to a higher sludge age of the biofilm, which allows complete acclimation to the contaminants. Operating conditions played an important role, high mixed liquor suspended solids (MLSS) and sludge retention time (SRT) being necessary to achieve these high removal rates. Although pharmaceuticals and linear alkylbenzene sulfonates showed high removal rates (65-100%), nonylphenols and phthalate could only be removed to 10-30%. RO significantly increased removal rates to 88% mean removal rate. PMID:25768224

  8. Effects of black liquor shocks on activated sludge treatment of bleached kraft pulp mill wastewater.

    PubMed

    Morales, Gabriela; Pesante, Silvana; Vidal, Gladys

    2015-01-01

    Kraft pulp mills use activated sludge systems to remove organic matter from effluents. Process streams may appear as toxic spills in treatment plant effluents, such as black liquor, which is toxic to microorganisms of the activated sludge. The present study evaluates the effects of black liquor shocks in activated sludge systems. Four black liquor shocks from 883 to 3,225 mg chemical oxygen demand-COD L(-1) were applied during 24 hours in a continuously operating lab-scale activated sludge system. Removal efficiencies of COD, color and specific compounds were determined. Moreover, specific oxygen uptake rate (SOUR), sludge volumetric index (SVI) and indicator microorganisms were evaluated. Results show that the addition of black liquor caused an increase in COD removal (76-67%) immediately post shock; followed two days later by a decrease (-19-50%). On the other hand, SOUR ranged between 0.152 and 0.336 mgO2 g(-1) volatile suspended solids-VSS• min(-1) during shocks, but the initial value was reestablished at hour 24. When the COD concentration of the shock was higher than 1,014 mg/L, the abundance of stalked ciliates and rotifers dropped. Finally, no changes in SVI were observed, with values remaining in the range 65.8-40.2 mL g(-1) total suspended solids-TSS during the entire operating process. Based on the results, the principal conclusion is that the activated sludge system with the biomass adapted to the kraft pulp effluent could resist a black liquor shock with 3,225 mgCOD L(-1) of concentration during 24 h, under this study's conditions. PMID:25837566

  9. Relationship of species-specific filament levels to filamentous bulking in activated sludge.

    PubMed

    Liao, Jiangying; Lou, Inchio; de los Reyes, Francis L

    2004-04-01

    To examine the relationship between activated-sludge bulking and levels of specific filamentous bacteria, we developed a statistics-based quantification method for estimating the biomass levels of specific filaments using 16S rRNA-targeted fluorescent in situ hybridization (FISH) probes. The results of quantitative FISH for the filament Sphaerotilus natans were similar to the results of quantitative membrane hybridization in a sample from a full-scale wastewater treatment plant. Laboratory-scale reactors were operated under different flow conditions to develop bulking and nonbulking sludge and were bioaugmented with S. natans cells to stimulate bulking. Instead of S. natans, the filament Eikelboom type 1851 became dominant in the reactors. Levels of type 1851 filaments extending out of the flocs correlated strongly with the sludge volume index, and extended filament lengths of approximately 6 x 10(8) micro m ml(-1) resulted in bulking in laboratory-scale and full-scale activated-sludge samples. Quantitative FISH showed that high levels of filaments occurred inside the flocs in nonbulking sludge, supporting the "substrate diffusion limitation" hypothesis for bulking. The approach will allow the monitoring of incremental improvements in bulking control methods and the delineation of the operational conditions that lead to bulking due to specific filaments. PMID:15066840

  10. Degradation of PPCPs in activated sludge from different WWTPs in Denmark.

    PubMed

    Chen, Xijuan; Vollertsen, Jes; Nielsen, Jeppe Lund; Dall, Agnieszka Gieraltowska; Bester, Kai

    2015-12-01

    Pharmaceuticals and Personal care products (PPCPs) are often found in effluents from wastewater treatment plants (WWTPs) due to insufficient removal during wastewater treatment processes. To understand the factors affecting the removal of PPCPs in classical activated sludge WWTPs, the present study was performed to assess the removal of frequently occurring pharmaceuticals (Naproxen, Fenoprofen, Ketoprofen, Dichlofenac, Carbamazepine) and the biocide Triclosan in activated sludge from four different Danish WWTPs. The respective degradation constants were compared to operational parameters previous shown to be of importance for degradation of micropollutants such as biomass concentration, and sludge retention time (SRT). The most rapid degradation, was observed for NSAID pharmaceuticals (55-90% for Fenoprofen, 77-94% for Ketoprofen and 46-90% for Naproxen), followed by Triclosan (61-91%), while Dichlofenac and Carbamazepine were found to be persistent in the systems. Degradation rate constants were calculated as 0.0026-0.0407 for NSAID pharmaceuticals and 0.0022-0.0065 for triclosan. No relationships were observed between degradation rates and biomass concentrations in the diverse sludges. However, for the investigated PPCPs, the optimal SRT was within 14-20 days (for these values degradation of these PPCPs was the most efficient). Though all of these parameters influence the degradation rate, none of them seems to be overall decisive. These observations indicate that the biological composition of the sludge is more important than the design parameters of the respective treatment plant. PMID:26407712

  11. The abundance and diversity of ammonia-oxidizing bacteria in activated sludge under autotrophic domestication.

    PubMed

    Li, Qiang; Ma, Chao; Sun, Shifang; Xie, Hui; Zhang, Wei; Feng, Jun; Song, Cunjiang

    2013-04-01

    Ammonia-oxidizing bacteria (AOB) play a key role in nitrogen-removal wastewater treatment plants (WWTPs) as they can transform ammonia into nitrite. AOB can be enriched in activated sludge through autotrophic domestication although they are difficult to be isolated. In this study, autotrophic domestication was carried out in a lab-scale sequencing-batch-reactor (SBR) system with two activated sludge samples. The ammonia removal capacity of the sludge samples increased during the domestication, and pH exhibited a negative correlation with the ammonia removal amount, which indicated that it was one important factor of microbial ammonia oxidation. The count of AOB, measured by the most probable number (MPN) method, increased significantly during autotrophic domestication as ammonia oxidation efficiency was enhanced. We investigated the changes in the community structure of AOB before and after domestication by amoA clone library and T-RFLP profile. It showed that AOB had been successfully enriched and the community structure significantly shifted during the domestication. Two groups of AOB were found in sludge samples: Nitrosomonas-like group remained predominant all the time and Nitrosospira-like group changed obviously. Simultaneously, the total heterotrophic bacteria were investigated by MPN and Biolog assay. The metabolic diversity of heterotrophs had changed minutely, although the count of them decreased significantly and lost superiority of microbial communities in the sludge. PMID:24620598

  12. Proposal for a screening test to evaluate the fate of organic micropollutants in activated sludge.

    PubMed

    Salvetti, Roberta; Vismara, Renato; Dal Ben, Ilaria; Gorla, Elena; Romele, Laura

    2011-04-01

    The concentrations of organic micropollutants are usually low in wastewaters (order of magnitude of mg L(-1)). However, their emission standards, especially in the case of carcinogenic and bioaccumulating substances, are often much lower (order of magnitude of microg L(-1)). Since these substances, in some cases, can be adsorbable or volatile, their removal via volatilization, biodegradation or sludge adsorption in a wastewater treatment plant (WWTP) becomes a significant feature to include in the usual design process, in order to verify the emission standards in gas and sludge too. In this study a simple screening batch test for the evaluation of the fate of organic micropollutants in water, air and sludge is presented. The test is set up by means of simple laboratory instruments and simulates an activated sludge tank process. In this study the results obtained for four substances with different chemical properties (i.e. toluene, benz(a)anthracene, phenol and benzene) are presented. The screening test proposed can be a useful tool to assess in about one month the fate of organic micropollutants in an activated sludge tank of a WWTP. Moreover, the test can constitute a useful support in the use of mathematical models, since it allows the verification of model results and the calibration of the reactions involved in the removal process. PMID:21877546

  13. Improved computational model (AQUIFAS) for activated sludge, integrated fixed-film activated sludge, and moving-bed biofilm reactor systems, part III: analysis and verification.

    PubMed

    Sen, Dipankar; Randall, Clifford W

    2008-07-01

    Research was undertaken to analyze and verify a model that can be applied to activated sludge, integrated fixed-film activated sludge (IFAS), and moving-bed biofilm reactor (MBBR) systems. The model embeds a biofilm model into a multicell activated sludge model. The advantage of such a model is that it eliminates the need to run separate computations for a plant being retrofitted from activated sludge to IFAS or MBBR. The biofilm flux rates for organics, nutrients, and biomass can be computed by two methods-a semi-empirical model of the biofilm that is relatively simpler, or a diffusional model of the biofilm that is computationally intensive. Biofilm support media can be incorporated to the anoxic and aerobic cells, but not the anaerobic cells. The model can be run for steady-state and dynamic simulations. The model was able to predict the changes in nitrification and denitrification at both pilot- and full-scale facilities. The semi-empirical and diffusional models of the biofilm were both used to evaluate the biofilm flux rates for media at different locations. The biofilm diffusional model was used to compute the biofilm thickness and growth, substrate concentrations, volatile suspended solids (VSS) concentration, and fraction of nitrifiers in each layer inside the biofilm. Following calibration, both models provided similar effluent results for reactor mixed liquor VSS and mixed liquor suspended solids and for the effluent organics, nitrogen forms, and phosphorus concentrations. While the semi-empirical model was quicker to run, the diffusional model provided additional information on biofilm thickness, quantity of growth in the biofilm, and substrate profiles inside the biofilm. PMID:18710147

  14. A laboratory-scale test of anaerobic digestion and methane production after phosphorus recovery from waste activated sludge.

    PubMed

    Takiguchi, Noboru; Kishino, Machiko; Kuroda, Akio; Kato, Junichi; Ohtake, Hisao

    2004-01-01

    In enhanced biological phosphorus removal (EBPR) processes, activated sludge microorganisms accumulate large quantities of polyphosphate (polyP) intracellularly. We previously discovered that nearly all of polyP could be released from waste activated sludge simply by heating it at 70 degrees C for about 1 h. We also demonstrated that this simple method was applicable to phosphorus (P) recovery from waste activated sludge in a pilot plant-scale EBPR process. In the present study, we evaluated the effect of this sludge processing (heat treatment followed by calcium phosphate precipitation) on anaerobic digestion in laboratory-scale experiments. The results suggested that the sludge processing for P recovery could improve digestive efficiency and methane productivity at both mesophilic (37 degrees C) and thermophilic (53 degrees C) temperatures. In addition, heat-treated waste sludge released far less P into the digested sludge liquor than did untreated waste sludge. It is likely that the P recovery step prior to anaerobic digestion has a potential advantage for controlling struvite (magnesium ammonium phosphate) deposit problems in sludge handling processes. PMID:16233643

  15. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Biotechnology Specimen Temperature Controller (BSTC) will cultivate cells until their turn in the bioreactor; it can also be used in culturing experiments that do not require the bioreactor. The BSTC comprises four incubation/refrigeration chambers individually set at 4 to 50 degreesC (near-freezing to above body temperature). Each chamber holds three rugged tissue chamber modules (12 total), clear Teflon bags holding 30 ml of growth media, all positioned by a metal frame. Every 7 to 21 days (depending on growth rates), an astronaut uses a shrouded syringe and the bags' needleless injection ports to transfer a few cells to a fresh media bag, and to introduce a fixative so that the cells may be studied after flight. The design also lets the crew sample the media to measure glucose, gas, and pH levels, and to inspect cells with a microscope. The controller is monitored by the flight crew through a 23-cm (9-inch) color computer display on the face of the BSTC. This view shows the BTSC with the front panel open. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  16. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Biotechnology Specimen Temperature Controller (BSTC) will cultivate cells until their turn in the bioreactor; it can also be used in culturing experiments that do not require the bioreactor. The BSTC comprises four incubation/refrigeration chambers individually set at 4 to 50 deg. C (near-freezing to above body temperature). Each chamber holds three rugged tissue chamber modules (12 total), clear Teflon bags holding 30 ml of growth media, all positioned by a metal frame. Every 7 to 21 days (depending on growth rates), an astronaut uses a shrouded syringe and the bags' needleless injection ports to transfer a few cells to a fresh media bag, and to introduce a fixative so that the cells may be studied after flight. The design also lets the crew sample the media to measure glucose, gas, and pH levels, and to inspect cells with a microscope. The controller is monitored by the flight crew through a 23-cm (9-inch) color computer display on the face of the BSTC. This view shows the BTSC with the front panel open. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators.

  17. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Bioreactor Demonstration System (BDS) comprises an electronics module, a gas supply module, and the incubator module housing the rotating wall vessel and its support systems. Nutrient media are pumped through an oxygenator and the culture vessel. The shell rotates at 0.5 rpm while the irner filter typically rotates at 11.5 rpm to produce a gentle flow that ensures removal of waste products as fresh media are infused. Periodically, some spent media are pumped into a waste bag and replaced by fresh media. When the waste bag is filled, an astronaut drains the waste bag and refills the supply bag through ports on the face of the incubator. Pinch valves and a perfusion pump ensure that no media are exposed to moving parts. An Experiment Control Computer controls the Bioreactor, records conditions, and alerts the crew when problems occur. The crew operates the system through a laptop computer displaying graphics designed for easy crew training and operation. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators. See No. 0101816 for a version without labels, and No. 0103180 for an operational schematic.

  18. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Bioreactor Demonstration System (BDS) comprises an electronics module, a gas supply module, and the incubator module housing the rotating wall vessel and its support systems. Nutrient media are pumped through an oxygenator and the culture vessel. The shell rotates at 0.5 rpm while the irner filter typically rotates at 11.5 rpm to produce a gentle flow that ensures removal of waste products as fresh media are infused. Periodically, some spent media are pumped into a waste bag and replaced by fresh media. When the waste bag is filled, an astronaut drains the waste bag and refills the supply bag through ports on the face of the incubator. Pinch valves and a perfusion pump ensure that no media are exposed to moving parts. An Experiment Control Computer controls the Bioreactor, records conditions, and alerts the crew when problems occur. The crew operates the system through a laptop computer displaying graphics designed for easy crew training and operation. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators. See No. 0101825 for a version with major elements labeled, and No. 0103180 for an operational schematic. 0101816

  19. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Bioreactor Demonstration System (BDS) comprises an electronics module, a gas supply module, and the incubator module housing the rotating wall vessel and its support systems. Nutrient media are pumped through an oxygenator and the culture vessel. The shell rotates at 0.5 rpm while the irner filter typically rotates at 11.5 rpm to produce a gentle flow that ensures removal of waste products as fresh media are infused. Periodically, some spent media are pumped into a waste bag and replaced by fresh media. When the waste bag is filled, an astronaut drains the waste bag and refills the supply bag through ports on the face of the incubator. Pinch valves and a perfusion pump ensure that no media are exposed to moving parts. An Experiment Control Computer controls the Bioreactor, records conditions, and alerts the crew when problems occur. The crew operates the system through a laptop computer displaying graphics designed for easy crew training and operation. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators. See No. 0101823 for a version without labels, and No. 0103180 for an operational schematic.

  20. NASA Bioreactor

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Bioreactor Demonstration System (BDS) comprises an electronics module, a gas supply module, and the incubator module housing the rotating wall vessel and its support systems. Nutrient media are pumped through an oxygenator and the culture vessel. The shell rotates at 0.5 rpm while the irner filter typically rotates at 11.5 rpm to produce a gentle flow that ensures removal of waste products as fresh media are infused. Periodically, some spent media are pumped into a waste bag and replaced by fresh media. When the waste bag is filled, an astronaut drains the waste bag and refills the supply bag through ports on the face of the incubator. Pinch valves and a perfusion pump ensure that no media are exposed to moving parts. An Experiment Control Computer controls the Bioreactor, records conditions, and alerts the crew when problems occur. The crew operates the system through a laptop computer displaying graphics designed for easy crew training and operation. The work is sponsored by NASA's Office of Biological and Physical Research. The bioreactor is managed by the Biotechnology Cell Science Program at NASA's Johnson Space Center (JSC). NASA-sponsored bioreactor research has been instrumental in helping scientists to better understand normal and cancerous tissue development. In cooperation with the medical community, the bioreactor design is being used to prepare better models of human colon, prostate, breast and ovarian tumors. Cartilage, bone marrow, heart muscle, skeletal muscle, pancreatic islet cells, liver and kidney are just a few of the normal tissues being cultured in rotating bioreactors by investigators. See No. 0101824 for a version with labels, and No. 0103180 for an operational schematic.

  1. Response of activated sludge to the treatment of oxytetracycline production waste stream.

    PubMed

    Liu, Miaomiao; Zhang, Yu; Ding, Ran; Gao, Yingxin; Yang, Min

    2013-10-01

    To investigate how the microbial community in activated sludge responded to high antibiotic levels, a bench-scale aerobic wastewater treatment system was used to treat oxytetracycline (OTC) mother liquor (OTC-ML). Removal efficiency of chemical oxygen demand decreased from 64.9 to 51.0 % when the OTC level increased from 191.6 to 620.5 mg/L, respectively. According to the cloning results, Psychrobacter and Cryptophyta were the dominant bacterium and eukaryote in the inoculated sludge, respectively, both of which related to low temperature. After OTC exposure, Alphaproteobacteria and Betaproteobacteria became the dominant bacteria, with a small proportion of Firmicutes, Actinobacteria appeared, and fungi (mainly Saccharomycotina) became the dominant eukaryotes, indicating the possible functions of these microorganisms in the wastewater treatment of OTC-ML. The relative abundance of nine tetracycline resistance genes and four mobile elements (class 1 integron, class 2 integron, transposon Tn916/1545, and pattern 1 insertion sequence common region) significantly increased from undetectable to 2.1 × 10(-3) in the inoculated sludge to 1.7 × 10(-4)-9.8 × 10(-1) in sludge exposed to 620.5 mg/L OTC by using real-time PCR. The variety of gene cassette arrays of class 1 integron in the sludge samples increased with increasing OTC exposure concentration. PMID:23188460

  2. Ammonia-methane two-stage anaerobic digestion of dehydrated waste-activated sludge.

    PubMed

    Nakashimada, Yutaka; Ohshima, Yasutaka; Minami, Hisao; Yabu, Hironori; Namba, Yuzaburo; Nishio, Naomichi

    2008-07-01

    The study investigated methane production from dehydrated waste-activated sludge (DWAS) with approximately 80% water content under thermophilic conditions. The repeated batch-wise treatment of DWAS using methanogenic sludge unacclimated to high concentrations of ammonia, increased the ammonia production up to 7,600 mg N per kilogram total wet sludge of total ammonia concentration, and stopped the methane production. Investigation revealed that the loading ratio of DWAS for methanogenic sludge influences anaerobic digestion. Methane production significantly decreased and ammonia concentration increased with the increase in loading ratio of DWAS. Since the semicontinuous culture revealed that approximately 50% of organic nitrogen in DWAS converted to ammonia at sludge retention time (SRT) after 4 days at 37 degrees C and 1.33 days at 55 degrees C, the previous stripping of the ammonia produced from DWAS was carried out. The stripping of ammonia increased methane production significantly. This ammonia-methane two-stage anaerobic digestion demonstrated a successful methane production at SRT 20 days in the semicontinuous operation using a laboratory-scale reactor system. PMID:18491038

  3. Enhancement of aerobic biodegradability potential of municipal waste activated sludge by ultrasonic aided bacterial disintegration.

    PubMed

    Kavitha, S; Jessin Brindha, G M; Sally Gloriana, A; Rajashankar, K; Yeom, Ick Tae; Rajesh Banu, J

    2016-01-01

    An investigation was performed to study the influence of ultrasonic aided bacterial disintegration on the aerobic degradability of sludge. In first phase of the study, effective floc disruption was achieved at an ultrasonic specific energy input of 2.45kJ/kg TS with 44.5mg/L of Extracellular Polymeric Substance (EPS) release including 0.035U/mL and 0.025U/mL protease and amylase activity respectively. In second phase, experimental outcomes revealed bacterial disintegration of floc disrupted-sludge showing a maximum solubilization of about 23% and was observed to be superior to bacterially disintegrated (11%) and control (6%), respectively. The result of aerobic biodegradability of ultrasonic aided bacterially pretreated sludge showed volatile solids (VS) degradation of about 40.2%. The kinetic study of aerobic biodegradability through non linear regression modelling reveals that floc disrupted sludge showed better biodegradability with decay constant of about 0.19d(-1) relatively higher than the control (0.14d(-1)) and bacterially disintegrated (0.17d(-1)) sludges. PMID:26479431

  4. Continuous treatment of the insensitive munitions compound N-methyl-p-nitro aniline (MNA) in an upflow anaerobic sludge blanket (UASB) bioreactor.

    PubMed

    Olivares, Christopher I; Wang, Junqin; Luna, Carlos D Silva; Field, Jim A; Abrell, Leif; Sierra-Alvarez, Reyes

    2016-02-01

    N-methyl-p-nitroaniline (MNA) is an ingredient of insensitive munitions (IM) compounds that serves as a plasticizer and helps reduce unwanted detonations. As its use becomes widespread, MNA waste streams will be generated, necessitating viable treatment options. We studied MNA biodegradation and its inhibition potential to a representative anaerobic microbial population in wastewater treatment, methanogens. Anaerobic biodegradation and toxicity assays were performed and an up-flow anaerobic sludge blanket reactor (UASB) was operated to test continuous degradation of MNA. MNA was transformed almost stoichiometrically to N-methyl-p-phenylenediamine (MPD). MPD was not mineralized; however, it was readily autoxidized and polymerized extensively upon aeration at pH = 9. In the UASB reactor, MNA was fully degraded up to a loading rate of 297.5 μM MNA d(-1). Regarding toxicity, MNA was very inhibitory to acetoclastic methanogens (IC50 = 103 μM) whereas MPD was much less toxic, causing only 13.9% inhibition at the highest concentration tested (1025 μM). The results taken as a whole indicate that anaerobic sludge can transform MNA to MPD continuously, and that the transformation decreases the cytotoxicity of the parent pollutant. MPD can be removed through extensive polymerization. These insights could help define efficient treatment options for waste streams polluted with MNA. PMID:26454121

  5. Identification of Triclosan-O-Sulfate and other transformation products of Triclosan formed by activated sludge.

    PubMed

    Chen, Xijuan; Casas, Mònica Escolà; Nielsen, Jeppe Lund; Wimmer, Reinhard; Bester, Kai

    2015-02-01

    Aerobic degradation experiments of Triclosan were performed in activated sludge to identify possible transformation products for this compound. During 7 days, the formation of biotransformation products such as 2,4-Dichlorophenol, 4-Chlorocatechol, 5-Hydroxy-Triclosan and other Monohydroxy-Triclosan derivatives as well as Dihydroxy-Triclosan-derivatives were observed. The structure of 5-Hydroxy-Triclosan was elucidated by NMR data for the first time in sludge degradation experiments. Additionally the production of a hitherto unknown transformation product in sludge, i.e., Triclosan-O-Sulfate was detected. During the incubations, the concentrations of this transformation product changed from zero to 330 μg L(-1). Based on the analysis of the biodegradation products, three types of reactions were identified: 1) chemical scission of ether bond to form phenols and catechols, 2) addition of OH moieties to the aromatic ring, and 3) adding of methyl or sulfate groups to the original hydroxyl group. PMID:25306094

  6. Characterization of metoprolol biodegradation and its transformation products generated in activated sludge batch experiments and in full scale WWTPs.

    PubMed

    Rubirola, A; Llorca, M; Rodriguez-Mozaz, S; Casas, N; Rodriguez-Roda, I; Barceló, D; Buttiglieri, G

    2014-10-15

    Metoprolol (MTP) is a compound of concern, considered as an emerging contaminant due to its high consumption, pseudopersistence and potential ecotoxicity. Activated sludge batch experiments were performed to evaluate the biological transformation of MTP and the formation of transformation products under different treatment conditions. Total MTP removal was obtained in aerobic conditions, and the formation of MTP known metabolites (metoprolol acid (MTPA), α-hydroxymetoprolol (α-HMTP) and O-desmethylmetoprolol (O-DMTP)) and unknown transformation products (TPs) was investigated. The three known metabolites and two new TPs generated along the experiments were identified by liquid chromatography coupled to high resolution mass spectrometry. For the two new TPs plausible structures were proposed based on the tentative identification. MTPA had the major ratio formation for the TPs identified along the experiments (up to 40% of initial MTP concentration after 96 h treatment) and its persistence through biological treatment was proven. Ecotoxicity studies using Vibrio fischeri bioluminescent bacteria in an acute toxicity test showed that MTP and its known TPs are not toxic with the exception of o-DMTP. Finally, MTP and its TPs were monitored in a full scale membrane bioreactor and in a full scale conventional urban wastewater treatment plant (WWTP) and the results were compared with those obtained in batch experiments. α-HMTP was detected for the first time in a WWTP influent whereas MTPA was detected in influent and effluent WWTP samples at much higher levels (up to 100 folds higher) than MTP itself remarking its high persistence. PMID:24973729

  7. Effect of process variables on the production of Polyhydroxyalkanoates by activated sludge.

    PubMed

    Mokhtarani, Nader; Ganjidoust, Hossein; Vasheghani Farahani, Ebrahim

    2012-01-01

    Polyhydroxyalkanoates are known to be temporarily stored by microorganisms in activated sludge, especially in anaerobic-aerobic processes. Due to the problems resulted from the disposals of plastic wastes and excess sludge of wastewater treatment plants, the production of polyhydroxyalkanoates by treating activated sludge and determining the effect of process variables were the main issues of this paper. In this research, an anaerobic-aerobic sequencing batch reactor was used to make microorganism adapted and a batch aerobic reactor was used for enriching them. The variables affecting polyhydroxyalkanoates production including aeration time, sludge retention time, and volatile fatty acids concentration of the influent in sequencing batch reactor, and also carbon to nitrogen ratio and cultivation time in polymer production reactor, were investigated using Taguchi statistical approach to determine optimum conditions. The maximum polymer production of 29% was achieved at sludge retention time of 5-10 days, aeration time of 2 hours, supplementation of 40% of volatile fatty acids in the influent and increasing of carbon to nitrogen ratio of polymer production reactor to above 25 g/g. Based on the results, in optimum conditions, the volatile fatty acids concentration which increased the production of polyhydroxyalkanoates up to 49% was the most effective variable. Carbon to nitrogen ratio, sludge retention time and aeration time were ranked as the next affecting parameters. Although the polyhydroxyalkanoates content achieved in present study is much lower than that by pure culture, but the proposed method may still serve well as an environmental friendly means to convert waste into valuable product. PMID:23369512

  8. FULL-SCALE DEMONSTRATION OF OPEN TANK OXYGEN ACTIVATED SLUDGE TREATMENT

    EPA Science Inventory

    This report presents an operating summary of a full-scale demonstration of the FMC open tank pure oxygen (FMC O2) activated sludge system, conducted at the facilities of the Metropolitan Denver Sewage Disposal District No. 1 (Metro) in Denver, Colorado. The system was operated ov...

  9. Bioremediation of heavy metal-contaminated effluent using optimized activated sludge bacteria

    NASA Astrophysics Data System (ADS)

    Bestawy, Ebtesam El.; Helmy, Shacker; Hussien, Hany; Fahmy, Mohamed; Amer, Ranya

    2013-03-01

    Removal of heavy metals from contaminated domestic-industrial effluent using eight resistant indigenous bacteria isolated from acclimatized activated sludge was investigated. Molecular identification using 16S rDNA amplification revealed that all strains were Gram-negative among which two were resistant to each of copper, cadmium and cobalt while one was resistant to each of chromium and the heavy metal mixture. They were identified as Enterobacter sp. (Cu1), Enterobacter sp. (Cu2), Stenotrophomonas sp. (Cd1), Providencia sp. (Cd2), Chryseobacterium sp. (Co1), Comamonas sp. (Co2), Ochrobactrum sp. (Cr) and Delftia sp. (M1) according to their resistance pattern. Strains Cu1, Cd1, Co2 and Cr were able to resist 275 mg Cu/l, 320 mg Cd/l, 140 mg Co/l and 29 mg Cr/l respectively. The four resistant strains were used as a mixture to remove heavy metals (elevated concentrations) and reduce the organic load of wastewater effluent. Results revealed that using the proposed activated sludge with the resistant bacterial mixture was more efficient for heavy metal removal compared to the activated sludge alone. It is therefore recommended that the proposed activated sludge system augmented with the acclimatized strains is the best choice to ensure high treatment efficiency and performance under metal stresses especially when industrial effluents are involved.

  10. Local adaptive approach toward segmentation of microscopic images of activated sludge flocs

    NASA Astrophysics Data System (ADS)

    Khan, Muhammad Burhan; Nisar, Humaira; Ng, Choon Aun; Lo, Po Kim; Yap, Vooi Voon

    2015-11-01

    Activated sludge process is a widely used method to treat domestic and industrial effluents. The conditions of activated sludge wastewater treatment plant (AS-WWTP) are related to the morphological properties of flocs (microbial aggregates) and filaments, and are required to be monitored for normal operation of the plant. Image processing and analysis is a potential time-efficient monitoring tool for AS-WWTPs. Local adaptive segmentation algorithms are proposed for bright-field microscopic images of activated sludge flocs. Two basic modules are suggested for Otsu thresholding-based local adaptive algorithms with irregular illumination compensation. The performance of the algorithms has been compared with state-of-the-art local adaptive algorithms of Sauvola, Bradley, Feng, and c-mean. The comparisons are done using a number of region- and nonregion-based metrics at different microscopic magnifications and quantification of flocs. The performance metrics show that the proposed algorithms performed better and, in some cases, were comparable to the state-of the-art algorithms. The performance metrics were also assessed subjectively for their suitability for segmentations of activated sludge images. The region-based metrics such as false negative ratio, sensitivity, and negative predictive value gave inconsistent results as compared to other segmentation assessment metrics.

  11. CRITICAL LITERATURE REVIEW AND RESEARCH NEEDED ON ACTIVATED SLUDGE SECONDARY CLARIFIERS

    EPA Science Inventory

    Secondary clarifiers are key to the successful performance of the activated sludge process. They serve to separate out the biological solids and produce a clear effluent and to concentrate the settled solids for return to the aeration basins. Clarifiers have served the purpose fo...

  12. An Operations Manual for Achieving Nitrification in an Activated Sludge Plant.

    ERIC Educational Resources Information Center

    Ontario Ministry of the Environment, Toronto.

    In Ontario, the attainment of nitrification (oxidation of ammonia) in activated sludge plants is receiving increased attention. Nitrification of waste water is a necessary requirement because it reduces plant discharge of nitrogenous oxygen demand and/or toxic ammonia. However, this new requirement will result in added responsibility for…

  13. Operational Control Procedures for the Activated Sludge Process, Part III-A: Calculation Procedures.

    ERIC Educational Resources Information Center

    West, Alfred W.

    This is the second in a series of documents developed by the National Training and Operational Technology Center describing operational control procedures for the activated sludge process used in wastewater treatment. This document deals exclusively with the calculation procedures, including simplified mixing formulas, aeration tank…

  14. Operational Control Procedures for the Activated Sludge Process, Part I - Observations, Part II - Control Tests.

    ERIC Educational Resources Information Center

    West, Alfred W.

    This is the first in a series of documents developed by the National Training and Operational Technology Center describing operational control procedures for the activated sludge process used in wastewater treatment. Part I of this document deals with physical observations which should be performed during each routine control test. Part II…

  15. THE COUPLED TRICKLING FILTER-ACTIVATED SLUDGE PROCESS: DESIGN AND PERFORMANCE

    EPA Science Inventory

    A case history report was prepared on the upgrading of the Livermore, California, Water Reclamation Plant from a conventional trickling filter plant with tertiary oxidation ponds to a coupled trickling filter-activated sludge plant producing a nitrified effluent low in BOD5, susp...

  16. Bioavailable and biodegradable dissolved organic nitrogen in activated sludge and trickling filter wastewater treatment plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A study was carried out to understand the fate of biodegradable dissolved organic nitrogen (BDON) and bioavailable dissolved organic nitrogen (ABDON) along the treatment trains of a wastewater treatment facility (WWTF) equipped with an activated sludge (AS) system and a WWTF equipped with a two-stag...

  17. OXYGEN-ACTIVATED SLUDGE PLANT COMPLETES TWO YEARS OF SUCCESSFUL OPERATION

    EPA Science Inventory

    A detailed report of the conversion to and operational performance of an oxygen-activated sludge system at the Westgate wastewater treatment plant in Fairfax County, Virginia, is given in this report. It is presented in the form of a case history including the time span leading u...

  18. Two-phased hyperthermophilic anaerobic co-digestion of waste activated sludge with kitchen garbage.

    PubMed

    Lee, Myungyeol; Hidaka, Taira; Tsuno, Hiroshi

    2009-11-01

    For co-digestion of waste activated sludge with kitchen garbage, hyperthermophilic digester systems that consisted of an acidogenic reactor operated at hyperthermophilic (70 degrees C) and a methanogenic reactor operated at mesophilic (35 degrees C), thermophilic (55 degrees C) or hyperthermophilic (65 degrees C) conditions in series were studied by comparing with a thermophilic digester system that consisted of thermophilic (55 degrees C) acidogenic and methanogenic reactors. Laboratory scale reactors were operated continuously fed with a substrate blend composed of concentrated waste activated sludge and artificial kitchen garbage. At the acidogenic reactor, solubilization efficiencies of chemical oxygen demand (COD), carbohydrate and protein at 70 degrees C were about 39%, 42% and 54%, respectively, and they were higher than those at 55 degrees C by around 10%. The system of acidogenesis at 70 degrees C and methanogenesis at 55 degrees C was stable and well-functioned in terms of treatment performances and low ammonium nitrogen concentrations. Microbial community analysis was conducted using a molecular biological method. The key microbe determined at the hyperthermophilic acidogenesis step was Coprothermobacter sp., which was possibly concerned with the degradation of protein in waste activated sludge. The present study proved that the hyperthermophilic system was advantageous for treating substrate blends containing high concentrations of waste activated sludge. PMID:19804865

  19. Effects of TiO2 and Ag nanoparticles on polyhydroxybutyrate biosynthesis by activated sludge bacteria.

    PubMed

    Priester, John H; Van De Werfhorst, Laurie C; Ge, Yuan; Adeleye, Adeyemi S; Tomar, Shivira; Tom, Lauren M; Piceno, Yvette M; Andersen, Gary L; Holden, Patricia A

    2014-12-16

    Manufactured nanomaterials (MNMs) are increasingly incorporated into consumer products that are disposed into sewage. In wastewater treatment, MNMs adsorb to activated sludge biomass where they may impact biological wastewater treatment performance, including nutrient removal. Here, we studied MNM effects on bacterial polyhydroxyalkanoate (PHA), specifically polyhydroxybutyrate (PHB), biosynthesis because of its importance to enhanced biological phosphorus (P) removal (EBPR). Activated sludge was sampled from an anoxic selector of a municipal wastewater treatment plant (WWTP), and PHB-containing bacteria were concentrated by density gradient centrifugation. After starvation to decrease intracellular PHB stores, bacteria were nutritionally augmented to promote PHB biosynthesis while being exposed to either MNMs (TiO2 or Ag) or to Ag salts (each at a concentration of 5 mg L(-1)). Cellular PHB concentration and PhyloChip community composition were analyzed. The final bacterial community composition differed from activated sludge, demonstrating that laboratory enrichment was selective. Still, PHB was synthesized to near-activated sludge levels. Ag salts altered final bacterial communities, although MNMs did not. PHB biosynthesis was diminished with Ag (salt or MNMs), indicating the potential for Ag-MNMs to physiologically impact EBPR through the effects of dissolved Ag ions on PHB producers. PMID:25409530

  20. TOC, ATP AND RESPIRATION RATE AS CONTROL PARAMETERS FOR THE ACTIVATED SLUDGE PROCESS

    EPA Science Inventory

    This research was conducted to determine the feasibility of using TOC, ATP and respiration rates as tools for controlling a complete mix activated sludge plant handling a significant amount of industrial waste. Control methodology was centered on using F/M ratio which was determi...

  1. FATE OF WATER SOLUBLE AZO DYES IN THE ACTIVATED SLUDGE PROCESS

    EPA Science Inventory

    The objective of this study was to determine the partitioning of water soluble azo dyes in the activated sludge process (ASP). Azo dyes are of concern because some of the dyes, dye precursors , and/or their degradation products such as aromatic amines (which are also dye precurso...

  2. Fate of organic matter during moderate heat treatment of sludge: kinetics of biopolymer and hydrolytic activity release and impact on sludge reduction by anaerobic digestion.

    PubMed

    Lefebvre, D; Dossat-Létisse, V; Lefebvre, X; Girbal-Neuhauser, E

    2014-01-01

    Temperature-phased anaerobic digestion with a 50-70 °C pre-treatment is widely proposed for sludge. Here, such a sludge pre-treatment (65 °C) was studied against the physical, enzymatic and biodegradation processes. The soluble and particulate fractions were analysed in terms of biochemical composition and hydrolytic enzymatic activities. Two kinetics of organic matter solubilisation were observed: a rapid transfer of the weak-linked biopolymers to the water phase, including sugars, proteins or humic acid-like substances, to the water phase, followed by a slow and long-term solubilisation of proteins and humic acid-like substances. In addition, during the heat treatment a significant pool of thermostable hydrolytic enzymes including proteases, lipases and glucosidases remains active. Consequently, a global impact on organic matter was the transfer of the biodegradable chemical oxygen demand (COD) from the particulate to the soluble fraction as evaluated by the biological methane potential test. However, the total biodegradable COD content of the treated sludge remained constant. The heat process improves the bio-accessibility of the biodegradable molecules but doesn't increase the inherent sludge biodegradability, suggesting that the chemistry of the refractory proteins and humic acids seems to be the real limit to sludge digestion. PMID:24804656

  3. High-rate activated sludge communities have a distinctly different structure compared to low-rate sludge communities, and are less sensitive towards environmental and operational variables.

    PubMed

    Meerburg, Francis A; Vlaeminck, Siegfried E; Roume, Hugo; Seuntjens, Dries; Pieper, Dietmar H; Jauregui, Ruy; Vilchez-Vargas, Ramiro; Boon, Nico

    2016-09-01

    High-rate activated sludge processes allow for the recovery of organics and energy from wastewaters. These systems are operated at a short sludge retention time and high sludge-specific loading rates, which results in a higher sludge yield and better digestibility than conventional, low-rate activated sludge. Little is known about the microbial ecology of high-rate systems. In this work, we address the need for a fundamental understanding of how high-rate microbial communities differ from low-rate communities. We investigated the high-rate and low-rate communities in a sewage treatment plant in relation to environmental and operational variables over a period of ten months. We demonstrated that (1) high-rate and low-rate communities are distinctly different in terms of richness, evenness and composition, (2) high-rate community dynamics are more variable and less shaped by deterministic factors compared to low-rate communities, (3) sub-communities of continuously core and transitional members are more shaped by deterministic factors than the continuously rare members, both in high-rate and low-rate communities, and (4) high-rate community members showed a co-occurrence pattern similar to that of low-rate community members, but were less likely to be correlated to environmental and operational variables. These findings provide a basis for further optimization of high-rate systems, in order to facilitate resource recovery from wastewater. PMID:27183209

  4. Multimembrane Bioreactor

    NASA Technical Reports Server (NTRS)

    Cho, Toohyon; Shuler, Michael L.

    1989-01-01

    Set of hydrophilic and hydrophobic membranes in bioreactor allows product of reaction to be separated, while nutrients fed to reacting cells and byproducts removed from them. Separation process requires no externally supplied energy; free energy of reaction sufficient. Membranes greatly increase productivity of metabolizing cells by continuously removing product and byproducts, which might otherwise inhibit reaction, and by continuously adding oxygen and organic nutrients.

  5. Fouling potential evaluation of soluble microbial products (SMP) with different membrane surfaces in a hybrid membrane bioreactor using worm reactor for sludge reduction.

    PubMed

    Li, Zhipeng; Tian, Yu; Ding, Yi; Chen, Lin; Wang, Haoyu

    2013-07-01

    The fouling characteristics of soluble microbial products (SMP) in the membrane bioreactor coupled with Static Sequencing Batch Worm Reactor (SSBWR-MBR) were tested with different types of membranes. It was noted that the flux decrements of S-SMP (SMP in SSBWR-MBR) with cellulose acetate (CA), polyvinylidene fluoride (PVDF) and polyether sulfones (PES) membranes were respectively 6.7%, 8.5% and 9.5% lower compared to those of C-SMP (SMP in Control-MBR) with corresponding membranes. However, for both the filtration of the C-SMP and S-SMP, the CA membrane exhibited the fastest diminishing rate of flux among the three types of membranes. The surface morphology analysis showed that the CA membrane exhibited more but smaller protuberances compared to the PVDF and PES. The second minimums surrounding each protruding asperity on CA membrane were more than those on the PVDF and PES membranes, enhancing the attachment of SMP onto the membrane surface. PMID:23685647

  6. Response of biodegradation characteristics of unacclimated activated sludge to moderate pressure in a batch reactor.

    PubMed

    Xu, Rui-Xiao; Li, Bing; Zhang, Yong; Si, Ling; Zhang, Xian-Qiu; Xie, Biao

    2016-04-01

    This study was aimed to investigate the effect of moderate pressure on unacclimated activated sludge. Process of organic degradation, variation of carbon dioxide (CO2) concentration of off-gas and characteristics of extracellular polymeric substances (EPS) of activated sludge were analyzed using pressure-atmospheric comparative experiments in bench-scale batch reactors. It was found that moderate pressure increased the degradation rate more dramatically when the biological process ran under a higher organic load with much more oxygen demand, which illuminated that applications of the pressurized method to high concentration organic wastewaters would be more reasonable and practicable. High oxygen transfer impetus increased utilization of oxygen which not only promoted the biodegradation of organics in wastewater, but also led to more EPS consumption in activated sludge. CO2 concentration of off-gas was lower in the earlier stage due to CO2 being pressed into the liquid phase and converted into inorganic carbon (IC). More CO2 emission was observed during the pressurized aerobic process 160 min later. EPS in pressurized reactor was much lower, which may be an important way of sludge reduction by pressurized technology. PMID:26802261

  7. Bacteriophages of wastewater foaming-associated filamentous Gordonia reduce host levels in raw activated sludge

    PubMed Central

    Liu, Mei; Gill, Jason J.; Young, Ry; Summer, Elizabeth J.

    2015-01-01

    Filamentous bacteria are a normal and necessary component of the activated sludge wastewater treatment process, but the overgrowth of filamentous bacteria results in foaming and bulking associated disruptions. Bacteriophages, or phages, were investigated for their potential to reduce the titer of foaming bacteria in a mixed-microbial activated sludge matrix. Foaming-associated filamentous bacteria were isolated from activated sludge of a commercial wastewater treatment plan and identified as Gordonia species by 16S rDNA sequencing. Four representative phages were isolated that target G. malaquae and two un-named Gordonia species isolates. Electron microscopy revealed the phages to be siphophages with long tails. Three of the phages - GordTnk2, Gmala1, and GordDuk1 - had very similar ~76 kb genomes, with >93% DNA identity. These genomes shared limited synteny with Rhodococcus equi phage ReqiDocB7 and Gordonia phage GTE7. In contrast, the genome of phage Gsput1 was smaller (43 kb) and was not similar enough to any known phage to be placed within an established phage type. Application of these four phages at MOIs of 5–15 significantly reduced Gordonia host levels in a wastewater sludge model by approximately 10-fold as compared to non-phage treated reactors. Phage control was observed for nine days after treatment. PMID:26349678

  8. Entomotoxicity, protease and chitinase activity of Bacillus thuringiensis fermented wastewater sludge with a high solids content.

    PubMed

    Brar, Satinder K; Verma, M; Tyagi, R D; Valéro, J R; Surampalli, R Y

    2009-10-01

    This study investigated the production of biopesticides, protease and chitinase activity by Bacillus thuringiensis grown in raw wastewater sludge at high solids concentration (30 g/L). The rheology of wastewater sludge was modified with addition of Tween-80 (0.2% v/v). This addition resulted in 1.6 and 1.3-fold increase in cell and spore count, respectively. The maximum specific growth rate (micro(max)) augmented from 0.17 to 0.22 h(-1) and entomotoxicity (Tx) increased by 29.7%. Meanwhile, volumetric mass transfer coefficient (k(L)a) showed marked variations during fermentation, and oxygen uptake rate (OUR) increased 2-fold. The proteolytic activity increased while chitinase decreased for Tween amended wastewater sludge, but the entomotoxicity increased. The specific entomotoxicity followed power law when plotted against spore concentration and the relation between Tx and protease activity was linear. The viscosity varied and volume percent of particles increased in Tween-80 amended wastewater sludge and particle size (D(50)) decreased at the end of fermentation. Thus, there was an increase in entomotoxicity at higher suspended solids (30 g/L) as Tween addition improved rheology (viscosity, particle size, surface tension); enhanced maximum growth rate and OUR. PMID:19447031

  9. Stoichiometry and kinetics of poly-{beta}-hydroxybutyrate metabolism in aerobic, slow growing, activated sludge cultures

    SciTech Connect

    Beun, J.J.; Paletta, F.; Loosdrecht, M.C.M. Van; Heijnen, J.J.

    2000-02-20

    This paper discusses the poly-{beta}-hydroxybutyrate (PHB) metabolism in aerobic, slow growing, activated sludge cultures, based on experimental data and on a metabolic model. The dynamic conditions which occur in activated sludge processes were simulated in a 2-L sequencing batch reactor (SBR) by subjecting a mixed microbial population to successive periods of external substrate availability (feast period) and no external substrate availability (famine period). Under these conditions intracellular storage and consumption of PHB was observed. It appeared that in the feast period, 66% to almost 100% of the substrate consumed is used for storage of PHB, the remainder is used for growth and maintenance processes. Furthermore, it appeared that at high sludge retention time (SRT) the growth rate in the feast and famine periods was the same. With decreasing SRT the growth rate in the feast period increased relative to the growth rate in the famine period. Acetate consumption and PHB production in the feast period both proceeded with a zero-order rate in acetate and PHB concentration respectively. PHB consumption in the famine period could best be described kinetically with a nth order degradation equation in PHB concentration. The obtained results are discussed in the context of the general activated sludge models.

  10. The impact of peroxydisulphate and peroxymonosulphate on disintegration and settleability of activated sludge.

    PubMed

    Wacławek, Stanisław; Grübel, Klaudiusz; Černík, Miroslav

    2016-01-01

    Chemical treatment processes have mostly been considered as an efficient way for biosolid minimization. The improvement of sludge dewatering was more a welcome side-effect of these sequential processes. In this study, heat-activated sodium peroxydisulphate (PDS) and potassium peroxymonosulphate (MPS) were applied in order to disintegrate waste activated sludge (WAS). PDS and MPS treatment of WAS results in the polymer transfer of organic matter from the solid phase to the liquid phase. Our research work was done for chemical disintegration of WAS by PDS and MPS in doses of 0.2%, 0.4%, 0.6%, 0.8% and 1% (169.5, 339.0, 508.5, 678.0 and 847.5 mg [Formula: see text]) activated at temperatures of 60°C and 90°C for 30 min. The application of these methods causes the soluble chemical oxygen demand value to increase in the supernatant. In addition, there was a positive influence on the sludge volume index which decreased for the highest doses of PDS of over 63% and 77% and MPS of over 78% and 82% through heat activation at temperatures of 60°C and 90°C, respectively. Furthermore, MPS was more successful in the floc particle destruction, therefore it caused a higher sludge settlement acceleration (sedimentation/compaction speed) than PDS. The experimental results demonstrated that the application of heat-activated PDS and MPS may become a novel effective way of processing sewage sludge. PMID:26503018

  11. Calcium ion on membrane fouling reduction and bioflocculation promotion in membrane bioreactor at high salt shock.

    PubMed

    Zhang, Haifeng; Fan, Xue; Wang, Bin; Song, Lianfa

    2016-01-01

    Fouling propensity of activated sludge in membrane bioreactor (MBR) is closely related to the disturbance of a salt shock. In this work, the characteristics of membrane fouling and bioflocculation were compared in two laboratory-scale MBRs (one with calcium addition, MBR-Ca, the other without, MBR-C) with a transient salt shock. Particle size distributions, zeta potential, relative hydrophobicity, modified fouling index, the content of polysaccharides, proteins and calcium ions in different layers of sludge were monitored prior to, during and after the salt shock. Comparison with MBR-C showed that the recovery time and fouling rate of MBR-Ca were reduced by 50% and 34%, respectively. Remarkable variations of sludge properties in terms of bioflocculation, such as larger particle sizes, higher relative hydrophobicity and zeta potential, lower polysaccharides in supernatant, higher proteins/polysaccharides ratio in slime and loose bound extracellular polymeric substances, were observed in MBR-Ca after the salt shock. PMID:26524252

  12. Effects of long term irrigation with polluted water and sludge amendment on some soil enzyme activities

    SciTech Connect

    Topac, F.O.; Baskaya, H.S.; Alkan, U.; Katkat, A.V.

    2008-01-15

    The objective of this study was to determine the effects of wastewater sludge-fly ash mixtures on urease, dehydrogenase, alkaline phosphatase and beta-glucosidase activities in soils. In order to evaluate the probable effects of previous soil management practices (irrigation with polluted water) on soil enzymes, two different soil samples which were similar in physical properties, but different in irrigation practice were used. The application of wastewater sludges supplemented with varying doses of fly ash increased potential enzyme activities for a short period of time (3 months) in comparison to unamended soils. However, the activity levels generally showed a decreasing trend with increasing ash ratios indicating the inhibitory effect of fly ash. The urease and dehydrogenase activities were particularly lower in soils irrigated from a polluted stream, indicating the negative effects of the previous soil management on soil microbial activity.

  13. Optimization of Ozonation Process for the Reduction of Excess Sludge Production from Activated Sludge Process of Sago Industry Wastewater Using Central Composite Design

    PubMed Central

    Subha, B.; Muthukumar, M.

    2012-01-01

    Sago industries effluent containing large amounts of organic content produced excess sludge which is a serious problem in wastewater treatment. In this study ozonation has been employed for the reduction of excess sludge production in activated sludge process. Central composite design is used to study the effect of ozone treatment for the reduction of excess sludge production in sago effluent and to optimise the variables such as pH, ozonation time, and retention time. ANOVA showed that the coefficient determination value (R2) of VSS and COD reduction were 0.9689 and 0.8838, respectively. VSS reduction (81%) was achieved at acidic pH 6.9, 12 minutes ozonation, and retention time of 10 days. COD reduction (87%) was achieved at acidic pH 6.7, 8 minutes of ozonation time, and retention time of 6 days. Low ozonation time and high retention time influence maximum sludge reduction, whereas low ozonation time with low retention time was effective for COD reduction. PMID:22593666

  14. Assessment of free nitrous acid pre-treatment on a mixture of primary sludge and waste activated sludge: Effect of exposure time and concentration.

    PubMed

    Zahedi, S; Icaran, P; Yuan, Z; Pijuan, M

    2016-09-01

    Free nitrous acid (FNA) has been shown to enhance the biodegradability of waste activated sludge (WAS) but its effectiveness on the pre-treatment of mixed sludge is not known. This study explores the effectiveness of four different FNA concentrations (0, 2.49, 3.55, 4.62mgN-HNO2/L) and three exposure times (2, 5, 9h) lower than the ones reported in literature (24h) on WAS characteristics and specific methane production (SMP). FNA pre-treatment reduced sludge cell viability below 10% in all cases after an exposure time of 5h, increasing the solubility of the organic matter. The treated mixed sludge was used as substrate for the biochemical methane production tests to assess its SMP. Results showed a significant increase (up to 25%) on SMP when the sludge was pretreated with the lowest FNA concentration (2.49mgN-HNO2/L) during 2 and 5h but did not show any improvement at longer exposure times or higher FNA concentrations. PMID:27318660

  15. pH-dependent biotransformation of ionizable organic micropollutants in activated sludge.

    PubMed

    Gulde, Rebekka; Helbling, Damian E; Scheidegger, Andreas; Fenner, Kathrin

    2014-12-01

    Removal of micropollutants (MPs) during activated sludge treatment can mainly be attributed to biotransformation and sorption to sludge flocs, whereby the latter process is known to be of minor importance for polar organic micropollutants. In this work, we investigated the influence of pH on the biotransformation of MPs with cationic-neutral speciation in an activated sludge microbial community. We performed batch biotransformation, sorption control, and abiotic control experiments for 15 MPs with cationic-neutral speciation, one control MP with neutral-anionic speciation, and two neutral MPs at pHs 6, 7, and 8. Biotransformation rate constants corrected for sorption and abiotic processes were estimated from measured concentration time series with Bayesian inference. We found that biotransformation is pH-dependent and correlates qualitatively with the neutral fraction of the ionizable MPs. However, a simple speciation model based on the assumption that only the neutral species is efficiently taken up and biotransformed by the cells tends to overpredict the effect of speciation. Therefore, additional mechanisms such as uptake of the ionic species and other more complex attenutation mechanisms are discussed. Finally, we observed that the sorption coefficients derived from our control experiments were small and showed no notable pH-dependence. From this we conclude that pH-dependent removal of polar, ionizable organic MPs in activated sludge systems is less likely an effect of pH-dependent sorption but rather of pH-dependent biotransformation. The latter has the potential to cause marked differences in the removal of polar, ionizable MPs at different operational pHs during activated sludge treatment. PMID:25337862

  16. Environmental and resource implications of phosphorus recovery from waste activated sludge.

    PubMed

    Sørensen, Birgitte Lilholt; Dall, Ole Leinikka; Habib, Komal

    2015-11-01

    Phosphorus is an essential mineral resource for the growth of crops and thus necessary to feed the ever increasing global population. The essentiality and irreplaceability of phosphorus in food production has raised the concerns regarding the long-term phosphorus availability and the resulting food supply issues in the future. Hence, the recovery of phosphorus from waste activated sludge and other waste streams is getting huge attention as a viable solution to tackle the potential availability issues of phosphorus in the future. This study explores the environmental implications of phosphorus recovery from waste activated sludge in Denmark and further elaborates on the potential availability or scarcity issue of phosphorus today and 2050. Life cycle assessment is used to assess the possibility of phosphorus recovery with little or no environmental impacts compared to the conventional mining. The phosphorus recovery method assessed in this study consists of drying process, and thermal gasification of the waste activated sludge followed by extraction of phosphorus from the ashes. Our results indicate that the environmental impacts of phosphorus recovery in an energy efficient process are comparable to the environmental effects from the re-use of waste activated sludge applied directly on farmland. Moreover, our findings conclude that the general recommendation according to the waste hierarchy, where re-use of the waste sludge on farmland is preferable to material and energy recovery, is wrong in this case. Especially when phosphorus is a critical resource due to its life threatening necessity, lack of substitution options and potential future supply risk originating due to the high level of global supply concentration. PMID:25792438

  17. Comparison between sequential and simultaneous application of activated carbon with membrane bioreactor for trace organic contaminant removal.

    PubMed

    Nguyen, Luong N; Hai, Faisal I; Kang, Jinguo; Nghiem, Long D; Price, William E; Guo, Wenshan; Ngo, Huu H; Tung, Kuo-Lun

    2013-02-01

    The removal efficiency of 22 selected trace organic contaminants by sequential application of granular activated carbon (GAC) and simultaneous application of powdered activated carbon (PAC) with membrane bioreactor (MBR) was compared in this study. Both sequential application of GAC following MBR treatment (MBR-GAC) and simultaneous application of PAC within MBR (PAC-MBR) achieved improved removal (over 95%) of seven hydrophilic and biologically persistent compounds, which were less efficiently removed by MBR-only treatment (negligible to 70%). However, gradual breakthrough of these compounds occurred over an extended operation period. Charged compounds, particularly, fenoprop and diclofenac, demonstrated the fastest breakthrough (complete and 50-70%, in MBR-GAC and PAC-MBR, respectively). Based on a simple comparison from the long-term performance stability and activated carbon usage points of view, PAC-MBR appears to be a better option than MBR-GAC treatment. PMID:23313687

  18. A review and assessment of emerging technologies for the minimization of excess sludge production in wastewater treatment plants.

    PubMed

    Andreottola, Gianni; Foladori, Paola

    2006-01-01

    This paper focuses on the most promising technologies, available for full-scale applications, aimed to the on-site reduction of the excess sludge produced in municipal wastewater treatment plants. New techniques are added to the conventional stages of wastewater treatment, both integrated in the activated sludge bioreactors or applied as pretreatment for the enhancement of anaerobic digestion. A concise review about the alternatives based on physical, chemical or biological mechanisms is described. The present work highlights the efficiency of two such techniques, sonolysis and alkaline thermolysis integrated on the return flow from the secondary settler into the activated sludge bioreactors. The investigation on the effect of sonolysis and alkaline thermolysis on activated sludge samples was carried out by evaluating the COD concentration released in soluble and colloidal form and biodegradability measured by respirometry. The physicochemical treatments of sludge have several advantages (easy management, stability in performances and flexibility), but are associated with high operational costs that often limit the wide-scale applications. The application of hybrid methods, that couple almost two techniques for the enhancement of efficiency with respect to a single one, could optimise the sludge reduction, giving a significant saving in energy consumption for large-scale operations, but further research is needed. PMID:16849131

  19. Physiological activities associated with biofilm growth in attached and suspended growth bioreactors under aerobic and anaerobic conditions.

    PubMed

    Naz, Iffat; Seher, Shama; Perveen, Irum; Saroj, Devendra P; Ahmed, Safia

    2015-01-01

    This research work evaluated the biofilm succession on stone media and compared the biochemical changes of sludge in attached and suspended biological reactors operated under aerobic and anaerobic conditions. Stones incubated (30±2°C) with activated sludge showed a constant increase in biofilm weight up to the fifth and seventh week time under anaerobic and aerobic conditions, respectively, where after reduction (>80%) the most probable number index of pathogen indicators on ninth week was recorded. Reduction in parameters such as biological oxygen demand (BOD) (47.7%), chemical oxygen demand (COD, 41%), nitrites (60.2%), nitrates (105.5%) and phosphates (58.9%) and increase in dissolved oxygen (176.5%) of sludge were higher in aerobic attached growth reactors as compared with other settings. While, considerable reductions in these values were also observed (BOD, 53.8%; COD, 2.8%; nitrites, 28.6%; nitrates, 31.7%; phosphates, 41.4%) in the suspended growth system under anaerobic conditions. However, higher sulphate removal was observed in suspended (40.9% and 54.9%) as compared with biofilm reactors (28.2% and 29.3%). Six weeks biofilm on the stone media showed maximum physiological activities; thus, the operational conditions should be controlled to keep the biofilm structure similar to six-week-old biofilm, and can be used in fixed biofilm reactors for wastewater treatment. PMID:25609155

  20. In vitro antifungal activity of extracts obtained from Hypericum perforatum adventitious roots cultured in a mist bioreactor against planktonic cells and biofilm of Malassezia furfur.

    PubMed

    Simonetti, Giovanna; Tocci, Noemi; Valletta, Alessio; Brasili, Elisa; D'Auria, Felicia Diodata; Idoux, Alicia; Pasqua, Gabriella

    2016-01-01

    Xanthone-rich extracts from Hypericum perforatum root cultures grown in a Mist Bioreactor as antifungal agents against Malassezia furfur. Extracts of Hypericum perforatum roots grown in a bioreactor showed activity against planktonic cells and biofilm of Malassezia furfur. Dried biomass, obtained from roots grown under controlled conditions in a ROOTec mist bioreactor, has been extracted with solvents of increasing polarity (i.e. chloroform, ethyl acetate and methanol). The methanolic fraction was the richest in xanthones (2.86 ± 0.43 mg g(-1) DW) as revealed by HPLC. The minimal inhibitory concentration of the methanol extract against M. furfur planktonic cells was 16 μg mL(-1). The inhibition percentage of biofilm formation, at a concentration of 16 μg mL(-1), ranged from 14% to 39%. The results show that H. perforatum root extracts could be used as new antifungal agents in the treatment of Malassezia infections. PMID:26166743

  1. Effects of heavy metal and other elemental additives to activated sludge on growth of Eisenia foetida

    SciTech Connect

    Hartenstein, R.; Neuhauser, E.F.; Narahara, A.

    1981-09-01

    The approximate level at which added concentrations of certain elements would cause an activated sludge to induce a toxic effect upon the growth of Eisenia foetida was determined. During 43 trials on sludge samples obtained throughout 1 year of study, earthworms grew from 3 to 10 mg live wt at hatching to 792 mg +- 18% (mean +- C.V.) in 8 weeks, when sludge was 24/sup 0/C and contained no additives. None of several elements commonly used in microbial growth media enhanced the growth rate of the earthworm. At salt concentrations up to about 6.6% on a dry wt basis, none of six anions tested was in and of itself toxic, while five of 15 cations - Co, Hg, Cu, Ni, and Cd - appeared specifically to inhibit growth rate or cause death. Manganese, Cr, and Pb were innocuous even at the highest levels of application - 22,000, 46,000, and 52,000 mg/kg, respectively. Neither the anionic nor cationic component of certain salts, such as NaCl or NH/sub 4/Cl, could be said to inhibit growth, which occurred only at high concentrations of these salts (about 3.3 and/or 6.6%). Below 7 mmho/cm, toxicity could not be correlated with electrolytic conductance, though higher values may help to explain the nonspecific growth inhibitory effects of salts like NaCl and KCl. Nor could toxicity ever be ascribed to hydrogen ion activity, since sludge pH was not altered even at the highest salt dose. It is concluded that except under very extreme conditions, the levels of heavy metals and salts generally found in activated sludges will not have an adverse affect on the growth of E. foetida.

  2. Characterization of activated sludge exocellular polymers using several cation-associated extraction methods.

    PubMed

    Park, Chul; Novak, John T

    2007-04-01

    Evaluation of prior research and preliminary investigations in our laboratory led to the development of an extraction strategy that can be used to target different cations in activated sludge floc and extract their associated extracellular polymeric substances (EPS). The methods we used were the cation exchange resin (CER) procedure, base extraction, and sulfide addition to extract EPS linked with divalent cations, Al, and Fe, respectively. A comparison of sludge cations before and after CER extraction revealed that most of Ca(2+) and Mg(2+) were removed while Fe and Al remained intact, suggesting that this method is highly selective for Ca(2+) and Mg(2+)-bound EPS. The correlation between sludge Fe and sulfide-extracted EPS was indicative of selectivity of this method for Fe-bound EPS. The base extraction was less specific than the other methods but it was the method releasing the largest amount of Al into the extract, indicating that the method extracted Al-bound EPS. Concomitantly, the composition of extracted EPS and the amino acid composition differed for the three methods, indicating that EPS associated with different metals were not the same. The change in EPS following anaerobic and aerobic digestion was also characterized by the three extraction methods. CER-extracted EPS were reduced after aerobic digestion while they changed little by anaerobic digestion. On the other hand, anaerobic digestion was associated with the decrease in sulfide-extracted EPS. These results suggest that different types of cation-EPS binding mechanisms exist in activated sludge and that each cation-associated EPS fraction imparts unique digestion characteristics to activated sludge. PMID:17346764

  3. Can activated sludge treatments and advanced oxidation processes remove organophosphorus flame retardants?

    PubMed

    Cristale, Joyce; Ramos, Dayana D; Dantas, Renato F; Machulek Junior, Amilcar; Lacorte, Silvia; Sans, Carme; Esplugas, Santiago

    2016-01-01

    This study aims to determine the occurrence of 10 OPFRs (including chlorinated, nonchlorinated alkyl and aryl compounds) in influent, effluent wastewaters and partitioning into sludge of 5 wastewater treatment plants (WWTP) in Catalonia (Spain). All target OPFRs were detected in the WWTPs influents, and the total concentration ranged from 3.67 µg L(-1) to 150 µg L(-1). During activated sludge treatment, most OPFRs were accumulated in the sludge at concentrations from 35.3 to 9980 ng g(-1) dw. Chlorinated compounds tris(2-chloroethyl) phosphate (TCEP), tris(2-chloroisopropyl) phosphate (TCIPP) and tris(2,3-dichloropropyl) phosphate (TDCPP) were not removed by the conventional activated sludge treatment and they were released by the effluents at approximately the same inlet concentration. On the contrary, aryl compounds tris(methylphenyl) phosphate (TMPP) and 2-ethylhexyl diphenyl phosphate (EHDP) together with alkyl tris(2-ethylhexyl) phosphate (TEHP) were not detected in any of the effluents. Advanced oxidation processes (UV/H2O2 and O3) were applied to investigate the degradability of recalcitrant OPFRs in WWTP effluents. Those detected in the effluent sample (TCEP, TCIPP, TDCPP, tributyl phosphate (TNBP), tri-iso-butyl phosphate (TIBP) and tris(2-butoxyethyl) phosphate (TBOEP)) had very low direct UV-C photolysis rates. TBOEP, TNBP and TIBP were degraded by UV/H2O2 and O3. Chlorinated compounds TCEP, TDCPP and TCIPP were the most recalcitrant OPFR to the advanced oxidation processes applied. The study provides information on the partitioning and degradability pathways of OPFR within conventional activated sludge WWTPs. PMID:26540311

  4. Sewage treatment by a low energy membrane bioreactor.

    PubMed

    Zhang, Shaoyuan; van Houten, Renze; Eikelboom, Dick H; Doddema, Hans; Jiang, Zhaochun; Fan, Yaobo; Wang, Jusi

    2003-11-01

    A new membrane bioreactor (MBR) was developed for treatment of municipal wastewater. The MBR was mainly made up of an activated sludge reactor and a transverse flow membrane module, with an innovative configuration being in application between them. As a result, the transverse flow membrane module and low recirculation flow rate created advantages, such as lower energy consumption and more resistance to membrane fouling. The total energy consumption in the whole system was tested as 1.97+/-0.74 kWh/m(3) (permeate) while using periodical backwash with treated water and backflush with mixed liquor daily, being in the same level as a submerged membrane bioreactor, reported to be 2.4 kWh/m(3) (permeate). Energy consumption analysis in the system shows that the membrane module was more energy consuming than the other four parts listed as pump, aeration, pipe system and return sludge velocity lose, which consumed 37.66-52.20% of the total energy. The effluent from this system could be considered as qualified for greywater reuse in China, showing its potential application in the future. PMID:12895562

  5. Treatment of swine wastewater using chemically modified zeolite and bioflocculant from activated sludge.

    PubMed

    Guo, Junyuan; Yang, Chunping; Zeng, Guangming

    2013-09-01

    Sterilization, alkaline-thermal and acid-thermal treatments were applied to activated sludge and the pre-treated sludge was used as raw material for Rhodococcus R3 to produce polymeric substances. After 60 h of fermentation, bioflocculant of 2.7 and 4.2 g L(-1) were produced in sterilized and alkaline-thermal treated sludge as compared to that of 0.9 g L(-1) in acid-thermal treated sludge. Response surface methodology (RSM) was employed to optimize the treatment process of swine wastewater using the composite of bioflocculant and zeolite modified by calcining with MgO. The optimal flocculating conditions were bioflocculant of 24 mg L(-1), modified zeolite of 12 g L(-1), CaCl2 of 16 mg L(-1), pH of 8.3 and contact time of 55 min, and the corresponding removal rates of COD, ammonium and turbidity were 87.9%, 86.9%, and 94.8%. The use of the composite by RSM provides a feasible way to improve the pollutant removal efficiencies and recycle high-level of ammonium from wastewater. PMID:23810950

  6. Storage and degradation of poly-beta-hydroxybutyrate in activated sludge under aerobic conditions.

    PubMed

    Dircks, K; Henze, M; van Loosdrecht, M C; Mosbaek, H; Aspegren, H

    2001-06-01

    This research analyses the accumulation and degradation of poly-beta-hydroxybutyrate (PHB) in experiments with pulse addition of acetate to samples of activated sludge from pilot-plant and full-scale wastewater treatment plants. The experiments are divided into two periods: a feast period defined as the time when acetate is consumed and a famine period when the added acetate has been exhausted. In the feast period the significant process occurring is the production of PHB from acetate. The produced PHB is utilised in the famine period for production of glycogen and biomass. According to modelling results approximately 90% of the total potential growth occurs in the famine period utilising the stored PHB. The degradation rate for PHB in the famine period is found to be dependent on the level of PHB obtained at the end of the feast period. It was found that multiple order kinetics gives a good description of the rate of PHB degradation. The examined sludge of low SRT origin is found to degrade PHB faster than long SRT sludge at high fractions of PHB. The observed yield of glycogen on PHB in the famine period is in the range of 0.22-0.33 g COD/g COD depending on the SRT. The storage pool of glycogen in the examined sludge is more slowly degraded than PHB (COD/COD/h). PMID:11358308

  7. Start-up of membrane bioreactor and hybrid moving bed biofilm reactor-membrane bioreactor: kinetic study.

    PubMed

    Leyva-Díaz, J C; Poyatos, J M

    2015-01-01

    A hybrid moving bed biofilm reactor-membrane bioreactor (hybrid MBBR-MBR) system was studied as an alternative solution to conventional activated sludge processes and membrane bioreactors. This paper shows the results obtained from three laboratory-scale wastewater treatment plants working in parallel in the start-up and steady states. The first wastewater treatment plant was a MBR, the second one was a hybrid MBBR-MBR system containing carriers both in anoxic and aerobic zones of the bioreactor (hybrid MBBR-MBRa), and the last one was a hybrid MBBR-MBR system which contained carriers only in the aerobic zone (hybrid MBBR-MBRb). The reactors operated with a hydraulic retention time of 30.40 h. A kinetic study for characterizing heterotrophic biomass was carried out and organic matter and nutrients removals were evaluated. The heterotrophic biomass of the hybrid MBBR-MBRb showed the best kinetic performance in the steady state, with yield coefficient for heterotrophic biomass=0.30246 mg volatile suspended solids per mg chemical oxygen demand, maximum specific growth rate for heterotrophic biomass=0.00308 h(-1) and half-saturation coefficient for organic matter=3.54908 mg O2 L(-1). The removal of organic matter was supported by the kinetic study of heterotrophic biomass. PMID:26606088

  8. Addition of Al and Fe salts during treatment of paper mill effluents to improve activated sludge settlement characteristics.

    PubMed

    Agridiotis, V; Forster, C F; Carliell-Marquet, C

    2007-11-01

    Metal salts, ferrous sulphate and aluminium chloride, were added to laboratory-scale activated sludge plant treating paper mill effluents to investigate the effect on settlement characteristics. Before treatment the sludge was filamentous, had stirred sludge volume index (SSVI) values in excess of 300 and was moderately hydrophobic. The use of FeSO4.7H2O took three weeks to reduce the SSVI to 90. Microscopic examination showed that Fe had converted the filamentous flocs into a compact structure. When the iron dosing was stopped, the sludge returned to its bulking state within four weeks. In a subsequent trial, the addition of AlCl3 initially resulted in an improvement of the settlement index but then caused deterioration of the sludge properties. It is possible that aluminium was overdosed and caused charge reversal, increasing the SSVI. PMID:17113285

  9. The effect of iron dosing on reducing waste activated sludge in the oxic-settling-anoxic process.

    PubMed

    Yagci, Nevin; Novak, John T; Randall, Clifford W; Orhon, Derin

    2015-10-01

    This study evaluates the biological solid reduction in a conventional activated sludge system with an anoxic/anaerobic side stream reactor receiving 1/10 of return sludge mass. Influent iron concentrations and feeding modes were changed to explore the consistency between the influent iron concentration and yield values and to assess the impact of feeding pattern. The results indicated that sludge reduction occurs during alternately exposure of sludge to aerobic and anoxic/anaerobic conditions in a range of 38-87%. The sludge reduction values reached a maximum level with the higher iron concentrations. Thus, it is concluded that this configuration is more applicable for plants receiving high iron concentrations in the wastewaters. PMID:26141280

  10. Enhancement of waste activated sludge dewaterability using calcium peroxide pre-oxidation and chemical re-flocculation.

    PubMed

    Chen, Zhan; Zhang, Weijun; Wang, Dongsheng; Ma, Teng; Bai, Runying; Yu, Dezhong

    2016-10-15

    The effects of combined calcium peroxide (CaO2) oxidation with chemical re-flocculation on dewatering performance and physicochemical properties of waste activated sludge was investigated in this study. The evolutions of extracellular polymeric substances (EPS) distribution, composition and morphological properties were analyzed to unravel the sludge conditioning mechanism. It was found that sludge filtration performance was enhanced by calcium peroxide oxidation with the optimal dosage of 20 mg/gTSS. However, this enhancement was not observed at lower dosages due to the absence of oxidation and the performance deteriorated at higher dosages because of the release of excess EPS, mainly as protein-like substances. The variation in soluble EPS (SEPS) component can be fitted well with pseudo-zero-order kinetic model under CaO2 treatment. At the same time, extractable EPS content (SEPS and loosely bound EPS (LB-EPS)) were dramatically increased, indicating sludge flocs were effectively broken and their structure became looser after CaO2 addition. The sludge floc structure was reconstructed and sludge dewaterability was significantly enhanced using chemical re-flocculation (polyaluminium chloride (PACl), ferric iron (FeCl3) and polyacrylamide (PAM)). The inorganic coagulants performed better in improving sludge filtration dewatering performance and reducing cake moisture content than organic polymer, since they could act as skeleton builders and decrease the sludge compressibility. PMID:27450355

  11. Occurrence and activity of sulphate reducing bacteria in aerobic activated sludge systems.

    PubMed

    van den Brand, T P H; Roest, K; Chen, G H; Brdjanovic, D; van Loosdrecht, M C M

    2015-03-01

    In the sewage or wastewater treatment plant, biological sulphate reduction can occur spontaneously or be applied beneficially for its treatment. The results of this study can be applied to control SRB in the sewage and WWTP. Therefore, population diversity analyses of SRB for nine activated sludge wastewater treatment plants (WWTP) in the Netherlands and the effect of long-term (months) oxygen exposures on the SRB activity were carried out. T-RFLP and clone sequencing analyses of winter and summer samples revealed that (1) all WWTP have a similar SRB population, (2) there is no seasonal impact (10-20 °C) on the SRB population present in the WWTP and (3) Desulfobacter postgatei, Desulfovibrio desulfuricans and Desulfovibrio intestinalis were the most common and dominant SRB species observed in these samples, and origin from the sewage. Short term activity tests demonstrated that SRB were not active in the aerobic WWTP, but while flushed with N2-gas SRB became slightly active after 3 h. In a laboratory reactor at a dissolved oxygen concentration of <2 %, sulphate reduction occurred and 89 % COD removal was achieved. SRB grew in granules, in order to protect themselves for oxygen exposures. SRB are naturally present in aerobic WWTP, which is due to the formation of granules. PMID:25649202

  12. Effect of textile auxiliaries on the biodegradation of dyehouse effluent in activated sludge.

    PubMed

    Arslan Alaton, Idil; Insel, Güçlü; Eremektar, Gülen; Germirli Babuna, Fatos; Orhon, Derin

    2006-03-01

    The textile industry is confronted with serious environmental problems associated with its immense wastewater discharge, substantial pollution load, extremely high salinity, and alkaline, heavily coloured effluent. Particular sources of recalcitrance and toxicity in dyehouse effluent are two frequently used textile auxiliaries; i.e. dye carriers and biocidal finishing agents. The present experimental work reports the observation of scientific and practical significance related with the effect of two commercially important textile dye carriers and two biocidal finishing agents on biological activated sludge treatment at a textile preparation, dyeing and finishing plant in Istanbul. Respirometric measurements of the dyehouse effluent spiked with the selected textile chemicals were carried out for the assessment of the "readily biodegradable COD fraction" of the wastewater. The respirometric data obtained to visualize the effect of the selected textile auxiliaries on biomass activity was evaluated by an adopted activated sludge model. Results have indicated that the tested biocides did not exert any significant inhibitory effect on the treatment performance of the activated sludge reactor at the concentrations usually encountered in the final, total dyehouse effluent. The situation with the dye carriers was inherently different; one dye carrier appeared to be highly toxic and caused serious inhibition of the microbial respirometric activity, whereas the other dye carrier, also known as the more ecological alternative, i.e. the "Eco-Carrier", appeared to be biodegradable. Finally, the respirometric profile obtained for the Eco-Carrier was described by a simplified respirometric model. PMID:16098558

  13. Inhibition of the nitrification process in activated sludge by trivalent and hexavalent chromium, and partitioning of hexavalent chromium between sludge compartments.

    PubMed

    Novotnik, Breda; Zuliani, Tea; Ščančar, Janez; Milačič, Radmila

    2014-06-01

    The input of wastewater treatment plants (WWTPs) may contain high concentrations of Cr(III) and Cr(VI), which can affect nitrogen removal. In the present study the influence of different Cr(III) and Cr(VI) concentrations towards activated sludge nitrification was studied. To better understand the mechanisms of Cr(VI) toxicity, its reduction, adsorption and uptake in activated sludge was investigated in a batch growth system. Quantification of Cr(VI) was performed by speciated isotope dilution inductively coupled plasma mass spectrometry. It was found that Cr(VI) concentrations above 1.0 mg L(-1) and Cr(III) concentrations higher than 50 mg L(-1) negatively affected nitrification. Speciation studies indicated almost complete reduction of Cr(VI) after 24h of incubation when Cr(VI) concentrations were lower than 2.5 mg L(-1), whereas for Cr(VI) added to 5 mg L(-1) around 40% remained unreduced. The study of the partitioning of Cr in the activated sludge was performed by the addition of Cr(VI) in concentrations of 2.5 and 5.0 mg L(-1). Results revealed that Cr was allocated mainly within the intercellular compartments, whereas intracellular and adsorbed Cr represented less than 0.1% of the Cr sludge concentrations. Cr(VI) was reduced in all compartments, the most efficiently (about 94%) within the intracellular and intercellular fractions. The extent of reduction of adsorbed Cr was 92% and 80% for 2.5 and 5.0mg of Cr(VI) L(-1), respectively. The results of present investigation provide a new insight into the toxicity of Cr species towards activated sludge nitrification, which is of significant importance for the management of WWTPs in order to prevent them from inflows containing harmful Cr(VI) concentrations. PMID:24462082

  14. Ozonation effects for excess sludge reduction on bacterial communities composition in a full-scale activated sludge plant for domestic wastewater treatment.

    PubMed

    Chiellini, C; Gori, R; Tiezzi, A; Brusetti, L; Pucciarelli, S; D'Amato, E; Chiavola, A; Sirini, P; Lubello, C; Petroni, G

    2014-01-01

    Activated sludge process is the most widely diffused system to treat wastewater to control the discharge of pollutants into the environment. Microorganisms are responsible for the removal of organic matter, nitrogen, phosphorous and other emerging contaminants. The environmental conditions of biological reactors significantly affects the ecology of the microbial community and, therefore, the performance of the treatment process. In the last years, ozone has been used to reduce excess sludge production by wastewater treatment plants (WWTPs), whose disposal represents one of the most relevant operational costs. The ozonation process has demonstrated to be a viable method to allow a consistent reduction in excess sludge. This study was carried out in a full-scale plant treating municipal wastewater in two parallel lines, one ozonated in the digestion tank and another used as a control. Bacterial communities of samples collected from both lines of digestion thanks were then compared to assess differences related to the ozonation treatment. Data were then analysed with terminal restriction fragment length polymorphism (T-RFLP) analysis on 16S rRNA gene. Differences between bacterial communities of both treated and untreated line appeared 2 weeks after the beginning of the treatment. Results demonstrated that ozonation treatment significantly affected the activated sludge in WWTP. PMID:24701944

  15. Molecular detection, isolation, and physiological characterization of functionally dominant phenol-degrading bacteria in activated sludge.

    PubMed

    Watanabe, K; Teramoto, M; Futamata, H; Harayama, S

    1998-11-01

    DNA was isolated from phenol-digesting activated sludge, and partial fragments of the 16S ribosomal DNA (rDNA) and the gene encoding the largest subunit of multicomponent phenol hydroxylase (LmPH) were amplified by PCR. An analysis of the amplified fragments by temperature gradient gel electrophoresis (TGGE) demonstrated that two major 16S rDNA bands (bands R2 and R3) and two major LmPH gene bands (bands P2 and P3) appeared after the activated sludge became acclimated to phenol. The nucleotide sequences of these major bands were determined. In parallel, bacteria were isolated from the activated sludge by direct plating or by plating after enrichment either in batch cultures or in a chemostat culture. The bacteria isolated were classified into 27 distinct groups by a repetitive extragenic palindromic sequence PCR analysis. The partial nucleotide sequences of 16S rDNAs and LmPH genes of members of these 27 groups were then determined. A comparison of these nucleotide sequences with the sequences of the major TGGE bands indicated that the major bacterial populations, R2 and R3, possessed major LmPH genes P2 and P3, respectively. The dominant populations could be isolated either by direct plating or by chemostat culture enrichment but not by batch culture enrichment. One of the dominant strains (R3) which contained a novel type of LmPH (P3), was closely related to Valivorax paradoxus, and the result of a kinetic analysis of its phenol-oxygenating activity suggested that this strain was the principal phenol digester in the activated sludge. PMID:9797297

  16. Fate and effect of naphthenic acids on oil refinery activated sludge wastewater treatment systems.

    PubMed

    Misiti, Teresa; Tezel, Ulas; Pavlostathis, Spyros G

    2013-01-01

    Naphthenic acids (NAs) are a complex group of alkyl-substituted acyclic, monocyclic and polycyclic carboxylic acids present in oil sands process waters, crude oil, refinery wastewater and petroleum products. Crude oil, desalter brine, influent, activated sludge mixed liquor and effluent refinery samples were received from six United States refineries. The total acid number (TAN) of the six crudes tested ranged from 0.12 to 1.5 mg KOH/g crude oil and correlated to the total NA concentration in the crudes. The total NA concentration in the desalter brine, influent, activated sludge mixed liquor and effluent samples ranged from 4.2 to 40.4, 4.5 to 16.6, 9.6 to 140.3 and 2.8 to 11.6 mg NA/L, respectively. The NAs in all wastewater streams accounted for less than 16% of the total COD, indicating that many other organic compounds are present and that NAs are a minor component in refinery wastewaters. Susceptibility tests showed that none of the activated sludge heterotrophic microcosms was completely inhibited by NAs up to 400 mg/L. Growth inhibition ranging from 10 to 59% was observed in all microcosms at and above 100 mg NA/L. NAs chronically-sorbed to activated sludge mixed liquor biomass and powdered activated carbon (PAC) were recalcitrant and persistent. More than 80% of the total NAs remained in the solid phase at the end of the 10-day desorption period (five successive desorption steps). Throughout a 90-day incubation period, the total NA concentration decreased by 33 and 51% in PAC-free and PAC-containing mixed liquor microcosms, respectively. The lower molecular weight fraction of NAs was preferentially degraded in both mixed liquors. The persistence of the residual, higher molecular weight NAs is likely a combination of molecular recalcitrance and decreased bioavailability when chronically-sorbed to the biomass and/or PAC. PMID:23141768

  17. Model development with defined biological mechanisms for xenobiotic treatment activated sludge at steady state.

    PubMed

    Chong, Nyuk-Min

    2015-06-01

    Activated sludge treatment of a xenobiotic organic compound, much different from treatment of biogenic organics, must be modeled with interactions involving a two-part biomass of degrader and nondegrader, which selectively or competitively grow on a two-part substrate of input xenobiotic and its biogenic metabolites. A xenobiotic treatment model was developed which incorporates kinetics of the growth of degrader and nondegrader, the line dividing metabolites into xenobiotic and biogenic, yields of degrader and nondegrader from utilization of their parts of substrates, and kinetics of degrader reversion to nondegrader due to instability of the degradative element degraders carry. Experimental activated sludge operated for treatment of a xenobiotic generated data for calibration of the model. With the input of influent xenobiotic concentration, mean cell and hydraulic residence times, and calibrated parameters, the model readily outputs concentrations of degrader, nondegrader, and effluent biogenic residue that closely match the results obtained from experiments. PMID:25561268

  18. Degradation of norgestrel by bacteria from activated sludge: comparison to progesterone.

    PubMed

    Liu, Shan; Ying, Guang-Guo; Liu, You-Sheng; Peng, Fu-Qiang; He, Liang-Ying

    2013-09-17

    Natural and synthetic progestagens in the environment have become a concern due to their adverse effects on aquatic organisms. Laboratory studies were performed to investigate aerobic biodegradation of norgestrel by bacteria from activated sludge in comparison with progesterone, and to identify their degradation products and biotransformation pathways. The degradation of norgestrel followed first order reaction kinetics (T1/2 = 12.5 d), while progesterone followed zero order reaction kinetics (T1/2 = 4.3 h). Four and eight degradation products were identified for norgestrel and progesterone, respectively. Six norgestrel-degrading bacterial strains (Enterobacter ludwigii, Aeromonas hydrophila subsp. dhakensis, Pseudomonas monteilii, Comamonas testosteroni, Exiguobacterium acetylicum, and Chryseobacterium indologenes) and one progesterone-degrading bacterial strain (Comamonas testosteroni) were successfully isolated from the enrichment culture inoculated with aerobic activated sludge. To our best knowledge, this is the first report on the biodegradation products and degrading bacteria for norgestrel under aerobic conditions. PMID:23952780

  19. Treatment of industrial effluents by a continuous system: electrocoagulation--activated sludge.

    PubMed

    Moisés, Tejocote-Pérez; Patricia, Balderas-Hernández; Barrera-Díaz, C E; Gabriela, Roa-Morales; Natividad-Rangel, Reyna

    2010-10-01

    A continuous system electrocoagulation--active sludge was designed and built for the treatment of industrial wastewater. The system included an electrochemical reactor with aluminum electrodes, a clarifier and a biological reactor. The electrochemical reactor was tested under different flowrates (50, 100 and 200 mL/min). In the biological reactor, the performance of different cultures of active sludge was assessed: coliform bacterial, ciliate and flagellate protozoa and aquatic fungus. Overall treatment efficiencies of color, turbidity and COD removal were 94%, 92% and 80%, respectively, under optimal conditions of 50 mL/min flowrate and using ciliate and flagellate protozoa. It was concluded that the system was efficient for the treatment of industrial wastewater. PMID:20570506

  20. Newly isolated alkalophilic Advenella species bioaugmented in activated sludge for high p-cresol removal.

    PubMed

    Xenofontos, Eleni; Tanase, Ana-Maria; Stoica, Ileana; Vyrides, Ioannis

    2016-03-25

    In this work, an alkalophilic bacterium (LVX-4) capable of using p-cresol as sole source of carbon and energy was screened and isolated from soil polluted by used oil. Phylogenetic (16S rRNA) and phenotypic characterization using Biolog GN microplates and API 20NE strips indicated that LVX-4 strain is a new Advenella species. It showed both the capability to degrade of p-cresol at high concentrations (750 mg/L) and to use p-cresol for growth in a pH from 7 to 10, although the optimum pH was 9. Moreover bioaugmentation of activated sludge with this strain lead to the complete removal of p-cresol in less than 100 h. This is the first study that shows the potential of Advenella sp. to be bioaugmented in activated sludge system for p-cresol biodegradation. PMID:26596887

  1. New mechanistically based model for predicting reduction of biosolids waste by ozonation of return activated sludge.

    PubMed

    Isazadeh, Siavash; Feng, Min; Urbina Rivas, Luis Enrique; Frigon, Dominic

    2014-04-15

    Two pilot-scale activated sludge reactors were operated for 98 days to provide the necessary data to develop and validate a new mathematical model predicting the reduction of biosolids production by ozonation of the return activated sludge (RAS). Three ozone doses were tested during the study. In addition to the pilot-scale study, laboratory-scale experiments were conducted with mixed liquor suspended solids and with pure cultures to parameterize the biomass inactivation process during exposure to ozone. The experiments revealed that biomass inactivation occurred even at the lowest doses, but that it was not associated with extensive COD solubilization. For validation, the model was used to simulate the temporal dynamics of the pilot-scale operational data. Increasing the description accuracy of the inactivation process improved the precision of the model in predicting the operational data. PMID:24572272

  2. Expression and transfer of engineered catabolic pathways harbored by Pseudomonas spp. introuduced into activated sludge microcosms

    SciTech Connect

    Nublein, K.; Maris, D.; Timmis, K.; Dwyer, D.F. )

    1992-10-01

    Two genetically engineered microorganisms (GEMs), Pseudomonas sp. strain B13 FR1(pFRC20P) (FR120) and Pseudomonas putida KT2440(pWWO-EB62) (EB62), were introduced into activated sludge microcosms that had the level of aeration, nutrient makeup, and microbial community structure of activated sludge reactors. FR120 contains an experimentally assembled ortho cleavage route for simultaneous degradation of 3-chlorobenzoate (3CB) and 4-methyl benzoate (4MB); EB62 contains a derivative TOL plasmid-encoded degradative pathway for toluene experimentally evolved so that it additionally processes 4-ethyl benzoate (4EB). Experiments assessed survival of the GEMs, their ability to degrade target substrates, and lateral transfer of plasmid-encoded recombinant DNA.

  3. Study of the sludge reduction in an oxic-settling-anaerobic activated sludge process based on UNITANK.

    PubMed

    Sun, L P; Chen, J F; Guo, W Z; Fu, X P; Tan, J X; Wang, T J

    2015-01-01

    An oxic-settling-anaerobic process (OSA) can effectively reduce sludge production, but most of the research studies on the OSA process have been either under laboratory test conditions or based on synthetic wastewater, which cannot fully reflect the performance and sludge reduction efficiency in existing OSA process. Thus, aiming at examining the sludge reduction efficiency and the stability of the OSA process, UNITANK and UNITANK-OSA processes were performed in a 120 m(3)/d pilot-scale system using actual sewage. The results indicate that UNITANK-OSA achieved a 48% reduction of the sludge compared to the reduction due to UNITANK, not considering the accumulation of the effluent-suspended solids. The effluent quality was not found to change significantly, except that the total phosphorus concentration increased slightly. The extracellular polymeric substances metal floc theory may, to some extent, explain this reduction in this study. The OSA process could be used to reform the classic wastewater treatment process to get lower sludge mass. PMID:25607677

  4. Impacts of powdered activated carbon addition on trihalomethane formation reactivity of dissolved organic matter in membrane bioreactor effluent.

    PubMed

    Ma, Defang; Gao, Yue; Gao, Baoyu; Wang, Yan; Yue, Qinyan; Li, Qian

    2014-12-01

    Characteristics and trihalomethane (THM) formation reactivity of dissolved organic matter (DOM) in effluents from two membrane bioreactors (MBRs) with and without powdered activated carbon (PAC) addition (referred to as PAC/MBR and MBR, respectively) were examined to investigate the effects of PAC addition on THM formation of MBR effluent during chlorination. PAC addition increased the specific UV absorbance. Hydrophobic DOM especially hydrophobic acids in PAC/MBR effluent (50%) were more than MBR effluent (42%). DOM with molecular weight <1 kDa constituted 12% of PAC/MBR effluent DOM, which was less than that of MBR effluent (16%). Data obtained from excitation and emission matrix fluorescence spectroscopy revealed that PAC/MBR effluent DOM contained more simple aromatic protein, but had less fulvic acid-like and soluble microbial by-product-like. PAC addition reduced the formation of bromine-containing THMs during chlorination of effluents, but increased THM formation reactivity of effluent DOM. PMID:25150685

  5. Simple method for the measurement of the hydrogenotrophic methanogenic activity of anaerobic sludges

    USGS Publications Warehouse

    Coates, J.D.; Coughlan, M.F.; Colleran, E.

    1996-01-01

    The specific hydrogenotrophic activity of anaerobic sludges is usually assayed by gas chromatographic analysis for methane in the headspace of sealed test vials. Gas is sampled with a pressure lock syringe which allows quantification independent of the pressure prevailing in the vials. An alternative method was developed using pressure transducer monitoring of the decrease in headspace gas pressure as the H2/CO2 substrate is converted to CH4. Application of a simple formula related the decrease at each sample point to millilitres of CH4 produced and gave values for the specific hydrogenotrophic activity of granular anaerobic sludge which were in good agreement with the values obtained by the more labor-intensive gas chromatographic method. The simplicity of the method facilitates multiple replicate analyses and allows more accurate determination of initial rates than is achievable by the gas chromatographic method which is prone to analytical error at the very low concentrations of CH4 present in the headspace during the early stages of the assay. Mass transfer of H2 from headspace to liquid was found to be rate-limiting and to result in significant under-estimation of the specific hydrogenotrophic activity of the granular sludge. A test protocol, which used a vial volatile suspended solids concentration between 1.7 and 8 g l-1; a 1:5 ratio between liquid and headspace; incubation of the vials horizontally with vigorous shaking (180 rev./min) and an initial H2/CO2 (80/20) gas pressure of 100-150 kPa was found to give reproducible and maximal values for the specific hydrogenotrophic activity of the test sludge.

  6. ALUM ADDITION AND STEP-FEED STUDIES IN OXYGEN-ACTIVATED SLUDGE

    EPA Science Inventory

    A plug flow, O2-activated sludge process was operated with alum addition to remove phosphorus and with lime addition to prevent the process pH from decreasing below 6.4. The O2 reactor was operated at F/M ratios between 0.18 to 0.24 gm of BOD5/gm of MLVSS/day in a typical co-curr...

  7. The efficiency of different phenol-degrading bacteria and activated sludges in detoxification of phenolic leachates.

    PubMed

    Kahru, A; Reiman, R; Rätsep, A

    1998-07-01

    Phenolic composition, toxicity and biodegradability of three different phenolic leachates/samples was studied. Samples A and C were the leachates from the oil-shale industry spent shale dumps at Kohtla-Järve, Estonia. Sample B was a laboratory-prepared synthetic mixture of 7 phenolic compounds mimmicking the phenolic composition of the leachate A. Toxicity of these 3 samples was analyzed using two photobacterial test (BioTox and Microtox), Daphnia test (DAPHTOXKIT F pulex) and rotifiers' test (ROTOXKIT F). All the LC50 values were in the range of 1-10%, leachate A being the most toxic. The growth and detoxifying potential (toxicity of the growth medium was measured using photobacterial tests) of 3 different phenol-utilizing bacteria and acclimated activated sludges was studied in shake-flask cultures. 30% leachate A (altogether 0.6 mM total phenolic compounds) was too toxic to rhodococci and they did not grow. Cell number of Kurthia sp. and Pseudomonas sp. in 30% leachate A increased by 2 orders of magnitude but despite of the growth of bacteria the toxicity of the leachate did not decrease even by 7 weeks of cultivation. However, if the activated sludge was used instead of pure bacterial cultures the toxicity of the 30% leachate A was eliminated already after 3 days of incubation. 30% samples B and C were detoxified by activated sludge even more rapidly, within 2 days. As the biodegradable part of samples A and B should be identical, the detoxification of leachate A compared to that of sample B was most probably inhibited by inorganic (e.g. sulphuric) compounds present in the leachate A. Also, the presence of toxic recalcitrant organic compounds in the leachate A (missed by chemical analysis) that were not readily biodegradable even by activated sludge consortium should not be excluded. PMID:9650267

  8. Denitrification Activity, Wood Loss, and N2O Emissions Over 9 Years From a Wood Chip Bioreactor

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Loss of nitrate from agricultural fields in subsurface drainage water is an important problem in the Midwestern United States and elsewhere. One possible strategy for reducing nitrate export is the use of denitrification bioreactors. A variety of experimental bioreactor designs have been shown to re...

  9. Biofilms Versus Activated Sludge: Considerations in Metal and Metal Oxide Nanoparticle Removal from Wastewater.

    PubMed

    Walden, Connie; Zhang, Wen

    2016-08-16

    The increasing application of metal and metal oxide nanoparticles [Me(O)NPs] in consumer products has led to a growth in concentration of these nanoparticles in wastewater as emerging contaminants. This may pose a threat to ecological communities (e.g., biological nutrient removal units) within treatment plants and those subject to wastewater effluents. Here, the toxicity, fate, and process implications of Me(O)NPs within wastewater treatment, specifically during activated sludge processing and biofilm systems are reviewed and compared. Research showed activated sludge achieves high removal rate of Me(O)NPs by the formation of aggregates through adsorption. However, recent literature reveals evidence that inhibition is likely for nutrient removal capabilities such as nitrification. Biofilm systems were much less studied, but show potential to resist Me(O)NP inhibition and achieve removal through possible retention by sorption. Implicating factors during bacteria-Me(O)NP interactions such as aggregation, surface functionalization, and the presence of organics are summarized. At current modeled levels, neither activated sludge nor biofilm systems can achieve complete removal of Me(O)NPs, thus allowing for long-term environmental exposure of diverse biological communities to Me(O)NPs in streams receiving wastewater effluents. Future research directions are identified throughout in order to minimize the impact of these nanoparticles released. PMID:27437755

  10. Treatment of biomass gasification wastewater using a combined wet air oxidation/activated sludge process

    SciTech Connect

    English, C.J.; Petty, S.E.; Sklarew, D.S.

    1983-02-01

    A lab-scale treatability study for using thermal and biological oxidation to treat a biomass gasification wastewater (BGW) having a chemical oxygen demand (COD) of 46,000 mg/l is described. Wet air oxidation (WA0) at 300/sup 0/C and 13.8 MPa (2000 psi) was used to initially treat the BGW and resulted in a COD reduction of 74%. This was followed by conventional activated sludge treatment using operating conditions typical of municipal sewage treatment plants. This resulted in an additional 95% COD removal. Overall COD reduction for the combined process was 99%. A detailed chemical analysis of the raw BGW and thermal and biological effluents was performed using gas chromatography/mass spectrometry (GC/MS). These results showed a 97% decrease in total extractable organics with WA0 and a 99.6% decrease for combined WA0 and activated sludge treatment. Components of the treated waters tended to be fewer in number and more highly oxidized. An experiment was conducted to determine the amount of COD reduction caused by volatilization during biological treatment. Unfortunately, this did not yield conclusive results. Treatment of BGW using WA0 followed by activated sludge appears to be very effective and investigations at a larger scale are recommended.

  11. The activated sludge ecosystem contains a core community of abundant organisms

    PubMed Central

    Saunders, Aaron M; Albertsen, Mads; Vollertsen, Jes; Nielsen, Per H

    2016-01-01

    Understanding the microbial ecology of a system requires that the observed population dynamics can be linked to their metabolic functions. However, functional characterization is laborious and the choice of organisms should be prioritized to those that are frequently abundant (core) or transiently abundant, which are therefore putatively make the greatest contribution to carbon turnover in the system. We analyzed the microbial communities in 13 Danish wastewater treatment plants with nutrient removal in consecutive years and a single plant periodically over 6 years, using Illumina sequencing of 16S ribosomal RNA amplicons of the V4 region. The plants contained a core community of 63 abundant genus-level operational taxonomic units (OTUs) that made up 68% of the total reads. A core community consisting of abundant OTUs was also observed within the incoming wastewater to three plants. The net growth rate for individual OTUs was quantified using mass balance, and it was found that 10% of the total reads in the activated sludge were from slow or non-growing OTUs, and that their measured abundance was primarily because of immigration with the wastewater. Transiently abundant organisms were also identified. Among them the genus Nitrotoga (class Betaproteobacteria) was the most abundant putative nitrite oxidizer in a number of activated sludge plants, which challenges previous assumptions that Nitrospira (phylum Nitrospirae) are the primary nitrite-oxidizers in activated sludge systems with nutrient removal. PMID:26262816

  12. Biodegradation of various molecular weights of linear polyethylene glycol (PEG) in activated sludge

    SciTech Connect

    Hansmann, M.A.; Bookland, E.A.; Keough, T.W.; Larson, R.J.

    1995-12-31

    Linear polyethylene glycols (PEG) of various average molecular weights (PEG 1000, PEG 3400, PEG 8000, PEG 20000) were tested in a semi-continuous activated sludge test (SCAS), followed by a CO{sub 2} production test to determine which MWs are inherently biodegradable. Complete biodegradation was confirmed analytically using matrix-assisted laser desorption ionization time of flight mass spectrometry (MALDI TOF MS). The SCAS test estimates the removal of the test substance during wastewater treatment in activated sludge. SCAS removal, as measured by soluble organic carbon (SOC) was > 90% for the PEG 1000, PEG 3400, and PEG 8000, while PEG 20000 showed a SCAS removal of 28%. These results indicate that SCAS removal was largely due to degradation. The CO{sub 2} production test measures the mineralization of the test substance using activated sludge from the SCAS units as the inoculum. The CO{sub 2} test results show that PEG 1000, PEG 3400, and PEG 8000 are inherently biodegradable, with an average %TC02 > 80% by day 50 and remaining SOC < 10% as measured at day 50. Complete loss of material was confirmed by MALDI TOF MS. The PEG 20000 showed 40% TCO2 by day 50, with 50% SOC remaining. MALDI TOF MS confirmed the presence of parent material. Based on these results, PEGs of MW 8000 and less appear to be biodegradable.

  13. Performance of phenol-acclimated activated sludge in the presence of various phenolic compounds

    NASA Astrophysics Data System (ADS)

    Lim, Jun-Wei; Tan, Je-Zhen; Seng, Chye-Eng

    2013-06-01

    The objective of this study was to evaluate the performance of phenol-acclimated activated sludge in the presence of various phenolic compounds in the separated batch reactors. The phenol-acclimated activated sludge was observed to be capable of completely removing phenol, o-cresol, m-cresol, and 4-chlorophenol. Nevertheless, in the presence of 2-chlorophenol and 3-chlorophenol merely at 50 mg/L, incomplete removal of these phenolic compounds were noticed. The specific oxygen uptake rate patterns obtained for phenol, o-cresol, m-cresol, and 4-chlorophenol could be used to approximate the end point of these phenolic compounds removal as well as to monitor the growth of biomass. As the 2-chlorophenol and 3-chlorophenol were only partially removed in the mixed liquor, the patterns of specific oxygen uptake rate attained for these phenolic compounds were not feasible for the similar estimation. The calculated toxicity percentages show the toxicity effects of phenolic compounds on the phenol-acclimated activated sludge followed the order of 2-chlorophenol ≈ 3-chlorophenol > 4-chlorophenol > o-cresol ≈ m-cresol > phenol.

  14. ASExpert: an integrated knowledge-based system for activated sludge plants.

    PubMed

    Sorour, M T; Bahgat, L M F; El, Iskandarani M A; Horan, N J

    2002-08-01

    The activated sludge process is commonly used for secondary wastewater treatment worldwide. This process is capable of achieving high quality effluent. However it has the reputation of being difficult to operate because of its poorly understood biological behaviour, variability of input flows and the need to incorporate qualitative data. To augment this incomplete knowledge with experience, knowledge-based systems were introduced in the 1980s however they didn't receive much popularity. This paper presents the Activated Sludge Expert system (ASExpert), which is a rule-based expert system plus a complete database tool proposed for use in activated sludge plants. The paper focuses on presenting the system's main features and capabilities to revive the interest in knowledge-based systems as a reliable means for monitoring plants. Then it presents the methodology adopted for ASExpert validation along with an assessment of testing results. Finally it concludes that expert systems technology has proved its importance for enhancing performance, especially if in the future it is integrated to a modern control system. PMID:12211453

  15. Cultivation of a bacterial consortium with the potential to degrade total petroleum hydrocarbon using waste activated sludge.

    PubMed

    Sivakumar, S; Song, Y C; Kim, S H; Jang, S H

    2015-11-01

    Waste activated sludge was aerobically treated to demonstrate multiple uses such as cultivating an oil degrading bacterial consortium; studying the influence of a bulking agent (peat moss) and total petroleum hydrocarbon concentration on bacterial growth and producing a soil conditioner using waste activated sludge. After 30 days of incubation, the concentration of oil-degrading bacteria was 4.3 x 10(8) CFU g(-1) and 4.5 x 10(8) CFU g(-1) for 5 and 10 g of total petroleum hydrocarbon, respectively, in a mixture of waste activated sludge (1 kg) and peat moss (0.1 kg). This accounts for approximately 88.4 and 91.1%, respectively, of the total heterotrophic bacteria (total-HB). The addition of bulking agent enhanced total-HB population and total petroleum hydrocarbon-degrading bacterial population. Over 90% of total petroleum hydrocarbon degradation was achieved by the mixture of waste activated sludge, bulking agent and total petroleum hydrocarbon. The results of physico-chemical parameters of the compost (waste activated sludge with and without added peat moss compost) and a substantial reduction in E. coli showed that the use of this final product did not exhibit risk when used as soil conditioner. Finally, the present study demonstrated that cultivation of total petroleum hydrocarbon-degrading bacterial consortium and production of compost from waste activated sludge by aerobic treatment was feasible. PMID:26688976

  16. Measuring the activities of higher organisms in activated sludge by means of mechanical shearing pretreatment and oxygen uptake rate.

    PubMed

    Hao, Xiaodi; Wang, Qilin; Cao, Yali; van Loosdrecht, Mark C M

    2010-07-01

    A pretreatment method was developed to assess the activities of higher organisms. The method is based on mechanical shearing to damage the large cells of the protozoan and metazoan community in activated sludge. The procedure was confirmed through experimentation to be effective in determining the activities of higher organisms by comparing oxygen uptake rates (OURs) before and after the higher organisms were eradicated. Shearing led to disintegration of flocs, which could be effectively reconstituted by centrifugation. The reconstitution of the sludge flocs was essential since otherwise the activity of the floc mass would be too high due to lack of diffusion limitation. Mechanical shearing had no influence on the morphology, quantity and specific activity of yeasts, and it was inferred that bacteria smaller than yeasts in size would also not be influenced by the applied shearing procedure. Moreover, the effect of filamentous organisms on the measured activities of higher organisms was experimentally demonstrated and analyzed, and determined to be so weak that it could be ignored. Based on these tests, five typical activated sludge processes were selected to measure the contribution of higher organisms to the original OUR. The measured activities of higher organisms ranged from 9.4 to 25.0% of the original OURs. PMID:20605188

  17. Stepwise calibration of the activated sludge model no. 1 at a partially denitrifying large wastewater treatment plant.

    PubMed

    Fall, C; Espinosa-Rodriguez, M A; Flores-Alamo, N; van Loosdrecht, M C M; Hooijmans, C M

    2011-11-01

    Activated sludge modeling technology is maturing; however, currently, there exists a great need to increase its use in daily engineering practice worldwide. A good way for building the capacities of the practitioners is to promote good modeling practices and standardize the protocols. In this study, a systematic procedure was proposed to calibrate the Activated Sludge Model No. 1 (ASM1) at a large wastewater treatment plant, by which the model adequately predicted the quality of the effluent and the sludge quantities. A hydraulics model was set up and validated through a tracer test. The Vesilind settling constants were measured and combined with the default value of the flocculent zone settling parameter, to calibrate the clarifiers. A virtual anoxic tank was installed in the return activated sludge to mimic the denitrification occurring in the settlers. In ASM1, the calibrated parameters were only two influent chemical oxygen demand fractions and one kinetic constant (oxygen half-saturation coefficient). PMID:22195426

  18. Microbial Community Dynamics and Activity Link to Indigo Production from Indole in Bioaugmented Activated Sludge Systems

    PubMed Central

    Deng, Jie; Deng, Ye; Van Nostrand, Joy D.; Wu, Liyou; He, Zhili; Qin, Yujia; Zhou, Jiti; Zhou, Jizhong

    2015-01-01

    Biosynthesis of the popular dyestuff indigo from indole has been comprehensively studied using pure cultures, but less has been done to characterize the indigo production by microbial communities. In our previous studies, a wild strain Comamonas sp. MQ was isolated from activated sludge and the recombinant Escherichia coli nagAc carrying the naphthalene dioxygenase gene (nag) from strain MQ was constructed, both of which were capable of producing indigo from indole. Herein, three activated sludge systems, G1 (non-augmented control), G2 (augmented with Comamonas sp. MQ), and G3 (augmented with recombinant E. coli nagAc), were constructed to investigate indigo production. After 132-day operation, G3 produced the highest yields of indigo (99.5 ± 3.0 mg/l), followed by G2 (27.3 ± 1.3 mg/l) and G1 (19.2 ± 1.2 mg/l). The microbial community dynamics and activities associated with indigo production were analyzed by Illumina Miseq sequencing of 16S rRNA gene amplicons. The inoculated strain MQ survived for at least 30 days, whereas E. coli nagAc was undetectable shortly after inoculation. Quantitative real-time PCR analysis suggested the abundance of naphthalene dioxygenase gene (nagAc) from both inoculated strains was strongly correlated with indigo yields in early stages (0–30 days) (P < 0.001) but not in later stages (30–132 days) (P > 0.10) of operation. Based on detrended correspondence analysis (DCA) and dissimilarity test results, the communities underwent a noticeable shift during the operation. Among the four major genera (> 1% on average), the commonly reported indigo-producing populations Comamonas and Pseudomonas showed no positive relationship with indigo yields (P > 0.05) based on Pearson correlation test, while Alcaligenes and Aquamicrobium, rarely reported for indigo production, were positively correlated with indigo yields (P < 0.05). This study should provide new insights into our understanding of indigo bio-production by microbial communities

  19. Enhancement of anaerobic biohydrogen/methane production from cellulose using heat-treated activated sludge.

    PubMed

    Lay, C H; Chang, F Y; Chu, C Y; Chen, C C; Chi, Y C; Hsieh, T T; Huang, H H; Lin, C Y

    2011-01-01

    Anaerobic digestion is an effective technology to convert cellulosic wastes to methane and hydrogen. Heat-treatment is a well known method to inhibit hydrogen-consuming bacteria in using anaerobic mixed cultures for seeding. This study aims to investigate the effects of heat-treatment temperature and time on activated sludge for fermentative hydrogen production from alpha-cellulose by response surface methodology. Hydrogen and methane production was evaluated based on the production rate and yield (the ability of converting cellulose into hydrogen and methane) with heat-treated sludge as the seed at various temperatures (60-97 degrees C) and times (20-60 min). Batch experiments were conducted at 55 degrees C and initial pH of 8.0. The results indicate that hydrogen and methane production yields peaked at 4.3 mmol H2/g cellulose and 11.6 mmol CH4/g cellulose using the seed activated sludge that was thermally treated at 60 degrees C for 40 min. These parameter values are higher than those of no-treatment seed (HY 3.6 mmol H2/g cellulose and MY 10.4 mmol CH4/g cellulose). The maximum hydrogen production rate of 26.0 mmol H2/L/d and methane production rate of 23.2 mmol CH4/L/d were obtained for the seed activated sludge that was thermally treated at 70 degrees C for 50 min and 60 degrees C for 40 min, respectively. PMID:21902022

  20. Sorption and Release of Organics by Primary, Anaerobic, and Aerobic Activated Sludge Mixed with Raw Municipal Wastewater

    PubMed Central

    Modin, Oskar; Saheb Alam, Soroush; Persson, Frank; Wilén, Britt-Marie

    2015-01-01

    New activated sludge processes that utilize sorption as a major mechanism for organics removal are being developed to maximize energy recovery from wastewater organics, or as enhanced primary treatment technologies. To model and optimize sorption-based activated sludge processes, further knowledge about sorption of organics onto sludge is needed. This study compared primary-, anaerobic-, and aerobic activated sludge as sorbents, determined sorption capacity and kinetics, and investigated some characteristics of the organics being sorbed. Batch sorption assays were carried out without aeration at a mixing velocity of 200 rpm. Only aerobic activated sludge showed net sorption of organics. Sorption of dissolved organics occurred by a near-instantaneous sorption event followed by a slower process that obeyed 1st order kinetics. Sorption of particulates also followed 1st order kinetics but there was no instantaneous sorption event; instead there was a release of particles upon mixing. The 5-min sorption capacity of activated sludge was 6.5±10.8 mg total organic carbon (TOC) per g volatile suspend solids (VSS) for particulate organics and 5.0±4.7 mgTOC/gVSS for dissolved organics. The observed instantaneous sorption appeared to be mainly due to organics larger than 20 kDa in size being sorbed, although molecules with a size of about 200 Da with strong UV absorbance at 215–230 nm were also rapidly removed. PMID:25768429

  1. Sorption and release of organics by primary, anaerobic, and aerobic activated sludge mixed with raw municipal wastewater.

    PubMed

    Modin, Oskar; Saheb Alam, Soroush; Persson, Frank; Wilén, Britt-Marie

    2015-01-01

    New activated sludge processes that utilize sorption as a major mechanism for organics removal are being developed to maximize energy recovery from wastewater organics, or as enhanced primary treatment technologies. To model and optimize sorption-based activated sludge processes, further knowledge about sorption of organics onto sludge is needed. This study compared primary-, anaerobic-, and aerobic activated sludge as sorbents, determined sorption capacity and kinetics, and investigated some characteristics of the organics being sorbed. Batch sorption assays were carried out without aeration at a mixing velocity of 200 rpm. Only aerobic activated sludge showed net sorption of organics. Sorption of dissolved organics occurred by a near-instantaneous sorption event followed by a slower process that obeyed 1st order kinetics. Sorption of particulates also followed 1st order kinetics but there was no instantaneous sorption event; instead there was a release of particles upon mixing. The 5-min sorption capacity of activated sludge was 6.5±10.8 mg total organic carbon (TOC) per g volatile suspend solids (VSS) for particulate organics and 5.0±4.7 mgTOC/gVSS for dissolved organics. The observed instantaneous sorption appeared to be mainly due to organics larger than 20 kDa in size being sorbed, although molecules with a size of about 200 Da with strong UV absorbance at 215-230 nm were also rapidly removed. PMID:25768429

  2. Effects of oxygen concentration on the nitrifying activity of an aerobic hybrid granular sludge reactor.

    PubMed

    Filali, Ahlem; Bessiere, Yolaine; Sperandio, Mathieu

    2012-01-01

    The aim of the work was to quantify the influence of the simultaneous presence of flocs and granules in the nitrifying activity in a sequencing batch airlift reactor (SBAR). The nitrification rate and oxygen limitation of flocs, granules and hybrid sludge was investigated using respirometric assays at different dissolved oxygen concentrations. The spatial distribution of Ammonium Oxidizing Bacteria (AOB) and Nitrite Oxidizing Bacteria (NOB) was investigated using fluorescence in situ hybridization (FISH). Results showed that the nitrification rate was much less sensitive to oxygen limitation in systems containing a fraction of flocs than in pure granular sludge. Ammonium Oxidizing Bacteria (AOB) were found to be distributed in similar quantities in flocs and granules whereas the Nitrite Oxidizing Bacteria (NOB) were located preferentially in granules. This study showed that the presence of flocs with granules could increase the robustness of the process to transitory reductions of aeration. PMID:22233907

  3. Effect of acclimation and nutrient supply on 5-tolyltriazole biodegradation with activated sludge communities.

    PubMed

    Herzog, Bastian; Yuan, Heyang; Lemmer, Hilde; Horn, Harald; Müller, Elisabeth

    2014-07-01

    The corrosion inhibitor 5-tolyltriazole (5-TTri) can have a detrimental impact on aquatic systems thus implying an acute need to reduce the effluent concentrations of 5-TTri. In this study, 5-TTri biodegradation was enhanced through acclimation and nutrient supply. Activated sludge communities (ASC) were setup in nine subsequent ASC generations. While generation two showed a lag phase of five days without biodegradation, generations four to nine utilized 5-TTri right after inoculation, with biodegradation rates from 3.3 to 5.2 mg L(-1)d(-1). Additionally, centrifuged AS supernatant was used to simulate the nutrient conditions in wastewater. This sludge supernatant (SS) significantly enhanced biodegradation, resulting in removal rates ranging from 3.2 to 5.0 mg L(-1)d(-1) without acclimation while the control groups without SS observed lower rates of ⩽ 2.2 mg L(-1)d(-1). PMID:24841493

  4. Effect of Worm Predation on Changes in Waste Activated Sludge Properties.

    PubMed

    Zhu, Xuefeng; Yuan, Wenyi; Wang, Zhiwei; Zhou, Mingyuan; Guan, Jie

    2016-05-01

    This study explored the effects of worm predation on changes in waste activated sludge properties. Results showed that the rate by which worm predation reduced mixed liquor volatile suspended solids (MLVSS) was approximately 23.7% ± 3.1%. Particle size distribution and extracellular polymeric substance (EPS) analyses indicated that the reduction of fine particles and EPS content in sludge predated by worms mainly increased dewaterability and reduced the ratio of MLVSS/mixed liquor suspended solids. Moreover, both mean particle size and protein/carbohydrate ratio increased. The results of three-dimensional excitation-emission matrix and gel filtration chromatogram analyses demonstrated the varied properties of soluble microbial products and EPS were attributed to the worms' selective predation of low molecular-weight organic matter, which facilitated the hydrolysis of macromolecular organic matter. PMID:27131302

  5. Experimental Assessment of the Degradation of "Unbiodegradable" Organic Solids in Activated Sludge.

    PubMed

    Friedrich, M; Takács, I; Tränckner, Jens

    2016-03-01

    In current process models activated sludge consists of biodegradable and unbiodegradable organic fractions. Recent evidence suggests that this approach may not be accurate because some of this "unbiodegradable" material may indeed be degradable. To improve sludge production predictions, it is important to know to what extent the "unbiodegradable" organic fraction is degradable. Assuming that volatile suspended solids (VSS) is a measure of the sum of biodegradable and unbiodegradable organic solids and the integral of the oxygen uptake rate (OUR) is representative of the biodegradable organics, the combination of these measurements can be used to predict the change of unbiodegradable organic solids within an aerobic digestion batch experiment. This procedure was used to estimate degradation rates of "unbiodegradable" VSS between 0.006 to 0.029 d(-1). The advantage of the proposed method is that the degradation rate can be determined directly based on measurements and relies on a limited number of assumptions. PMID:26931538

  6. Hydraulic characterization of an activated sludge reactor with recycling system by tracer experiment and analytical models.

    PubMed

    Sánchez, F; Viedma, A; Kaiser, A S

    2016-09-15

    Fluid dynamic behaviour plays an important role in wastewater treatment. An efficient treatment requires the inexistence of certain hydraulic problems such as dead zones or short-circuiting flows. Residence time distribution (RTD) analysis is an excellent technique for detecting these inefficiencies. However, many wastewater treatment installations include water or sludge recycling systems, which prevent us from carrying out a conventional tracer pulse experiment to obtain the RTD curve of the installation. This paper develops an RTD analysis of an activated sludge reactor with recycling system. A tracer experiment in the reactor is carried out. Three analytical models, derived from the conventional pulse model, are proposed to obtain the RTD curve of the reactor. An analysis of the results is made, studying which model is the most suitable for each situation. This paper is useful to analyse the hydraulic efficiency of reactors with recycling systems. PMID:27288672

  7. Utilization of molasses spentwash for production of bioplastics by waste activated sludge

    SciTech Connect

    Khardenavis, Anshuman A. Vaidya, Atul N.; Kumar, M. Suresh; Chakrabarti, Tapan

    2009-09-15

    Present study describes the treatment of molasses spentwash and its use as a potential low cost substrate for production of biopolymer polyhydroxybutyrate (PHB) by waste activated sludge. Fluorescence microscopy revealed the presence of PHB granules in sludge biomass which was further confirmed by fourier transform-infra-red spectroscopy (FT-IR) and {sup 13}C nuclear magnetic resonance (NMR). The processing of molasses spentwash was carried out for attaining different ratios of carbon and nitrogen (C:N). Highest chemical oxygen demand (COD) removal and PHB accumulation of 60% and 31% respectively was achieved with raw molasses spentwash containing inorganic nitrogen (C:N ratio = 28) followed by COD removal of 52% and PHB accumulation of 28% for filtered molasses containing inorganic nitrogen (C:N ratio = 29). PHB production yield (Y{sub p/s}) was highest (0.184 g g{sup -1} COD consumed) for deproteinized spentwash supplemented with nitrogen. In contrast, the substrate consumption and product formation were higher in case of raw spentwash. Though COD removal was lowest from deproteinized spentwash, evaluation of kinetic parameters suggested higher rates of conversion of available carbon to biomass and PHB. Thus the process provided dual benefit of conversion of two wastes viz. waste activated sludge and molasses spentwash into value-added product-PHB.

  8. Degradation of estradiol and ethinyl estradiol by activated sludge and by a defined mixed culture.

    PubMed

    Weber, Stefanie; Leuschner, Prisca; Kämpfer, Peter; Dott, Wolfgang; Hollender, Juliane

    2005-04-01

    The aerobic degradation of the natural hormone 17-beta-estradiol (E2) and the synthetic hormone 17-alpha-ethinyl estradiol (EE2) was investigated in batch experiments with activated sludge from a conventional and a membrane sewage treatment plant. E2 was converted to estrone (E1), the well known metabolite, and further completely transformed within 3 days. The turnover rates of E2 did not differ greatly between conventional and membrane activated sludge. EE2 was persistent in both sludges. By several transfers into fresh E2-medium an enrichment culture could be selected that used E2 as growth substrate. Further enrichment and isolation led to a defined mixed culture consisting of two strains, which were identified by a polyphasic approach as Achromobacter xylosoxidans and Ralstonia sp., respectively. The culture used E2 and E1 as growth substrates and transformed estriol (E3) and 16-alpha-hydroxyestrone but not the xenoestrogens bisphenol A, alpha-zearalenol, mestranol or EE2. The turnover rates of E2 were 0.025-0.1 microg h(-1) cfu(-1) and did not depend on the steroid concentration. PMID:15290133

  9. Mechanisms involved in Escherichia coli and Serratia marcescens removal during activated sludge wastewater treatment

    PubMed Central

    Orruño, Maite; Garaizabal, Idoia; Bravo, Zaloa; Parada, Claudia; Barcina, Isabel; Arana, Inés

    2014-01-01

    Wastewater treatment reduces environmental contamination by removing gross solids and mitigating the effects of pollution. Treatment also reduces the number of indicator organisms and pathogens. In this work, the fates of two coliform bacteria, Escherichia coli and Serratia marcescens, were analyzed in an activated sludge process to determine the main mechanisms involved in the reduction of pathogenic microorganisms during wastewater treatment. These bacteria, modified to express green fluorescent protein, were inoculated in an activated sludge unit and in batch systems containing wastewater. The results suggested that, among the different biological factors implied in bacterial removal, bacterivorous protozoa play a key role. Moreover, a representative number of bacteria persisted in the system as free-living or embedded cells, but their distribution into liquid or solid fractions varied depending on the bacterium tested, questioning the real value of bacterial indicators for the control of wastewater treatment process. Additionally, viable but nonculturable cells constituted an important part of the bacterial population adhered to solid fractions, what can be derived from the competition relationships with native bacteria, present in high densities in this environment. These facts, taken together, emphasize the need for reliable quantitative and qualitative analysis tools for the evaluation of pathogenic microbial composition in sludge, which could represent an undefined risk to public health and ecosystem functions when considering its recycling. PMID:25044599

  10. Mechanisms involved in Escherichia coli and Serratia marcescens removal during activated sludge wastewater treatment.

    PubMed

    Orruño, Maite; Garaizabal, Idoia; Bravo, Zaloa; Parada, Claudia; Barcina, Isabel; Arana, Inés

    2014-10-01

    Wastewater treatment reduces environmental contamination by removing gross solids and mitigating the effects of pollution. Treatment also reduces the number of indicator organisms and pathogens. In this work, the fates of two coliform bacteria, Escherichia coli and Serratia marcescens, were analyzed in an activated sludge process to determine the main mechanisms involved in the reduction of pathogenic microorganisms during wastewater treatment. These bacteria, modified to express green fluorescent protein, were inoculated in an activated sludge unit and in batch systems containing wastewater. The results suggested that, among the different biological factors implied in bacterial removal, bacterivorous protozoa play a key role. Moreover, a representative number of bacteria persisted in the system as free-living or embedded cells, but their distribution into liquid or solid fractions varied depending on the bacterium tested, questioning the real value of bacterial indicators for the control of wastewater treatment process. Additionally, viable but nonculturable cells constituted an important part of the bacterial population adhered to solid fractions, what can be derived from the competition relationships with native bacteria, present in high densities in this environment. These facts, taken together, emphasize the need for reliable quantitative and qualitative analysis tools for the evaluation of pathogenic microbial composition in sludge, which could represent an undefined risk to public health and ecosystem functions when considering its recycling. PMID:25044599

  11. Application of activated sludge to purify urban soils of Baku city from oil contamination

    NASA Astrophysics Data System (ADS)

    Babaev, M. P.; Nadzhafova, S. I.; Ibragimov, A. G.

    2015-07-01

    A biopreparation inducing oil destruction and increasing the biological activity of soils was developed on the basis of activated sludge. Its oxidative activity towards hydrocarbons was studied. The application of this biopreparation to oil-contaminated soil increased the population density of microorganisms, including destroyers of hydrocarbons, and accelerated oil decomposition. The degree of destruction of oil and oil products in the case of a single treatment of the soil with this biopreparation comprised 30 to 50% within 60 days. The presence of cellulose-decomposing microorganisms in this biopreparation also favored an accelerated decomposition of plant substances, including plant litter and sawdust applied to the urban soils as an adsorbent.

  12. Bioaugmentation of Activated Sludge by an Indigenous 3-Chloroaniline-Degrading Comamonas testosteroni Strain, I2gfp

    PubMed Central

    Boon, Nico; Goris, Johan; De Vos, Paul; Verstraete, Willy; Top, Eva M.

    2000-01-01

    A strain identified as Comamonas testosteroni I2 was isolated from activated sludge and found to be able to mineralize 3-chloroaniline (3-CA). During the mineralization, a yellow intermediate accumulated temporarily, due to the distal meta-cleavage of chlorocatechol. This strain was tested for its ability to clean wastewater containing 3-CA upon inoculation into activated sludge. To monitor its survival, the strain was chromosomally marked with the gfp gene and designated I2gfp. After inoculation into a lab-scale semicontinuous activated-sludge (SCAS) system, the inoculated strain maintained itself in the sludge for at least 45 days and was present in the sludge flocs. After an initial adaptation period of 6 days, complete degradation of 3-CA was obtained during 2 weeks, while no degradation at all occurred in the noninoculated control reactor. Upon further operation of the SCAS system, only 50% 3-CA removal was observed. Denaturing gradient gel electrophoresis (DGGE) of 16S rRNA genes revealed a dynamic change in the microbial community structure of the activated sludge. The DGGE patterns of the noninoculated and the inoculated reactors evolved after 7 days to different clusters, which suggests an effect of strain inoculation on the microbial community structure. The results indicate that bioaugmentation, even with a strain originating from that ecosystem and able to effectively grow on a selective substrate, is not permanent and will probably require regular resupplementation. PMID:10877785

  13. SIMPLIFIED INJECTION OF OXYGEN GAS INTO AN ACTIVATED SLUDGE PROCESS

    EPA Science Inventory

    The Las Virgenes Municipal Water District conducted a pilot investigation of the Simplox process at their Tapia Water Reclamation Facility in Calabasas, California. The Simplox process, developed by the Cosmodyne Division of Cordon International, involves covering an activated sl...

  14. The role of forward osmosis and microfiltration in an integrated osmotic-microfiltration membrane bioreactor system.

    PubMed

    Luo, Wenhai; Hai, Faisal I; Kang, Jinguo; Price, William E; Nghiem, Long D; Elimelech, Menachem

    2015-10-01

    This study investigates the performance of an integrated osmotic and microfiltration membrane bioreactor (O/MF-MBR) system for wastewater treatment and reclamation. The O/MF-MBR system simultaneously used microfiltration (MF) and forward osmosis (FO) membranes to extract water from the mixed liquor of an aerobic bioreactor. The MF membrane facilitated the bleeding of dissolved inorganic salts and thus prevented the build-up of salinity in the bioreactor. As a result, sludge production and microbial activity were relatively stable over 60 days of operation. Compared to MF, the FO process produced a better permeate quality in terms of nutrients, total organic carbon, as well as hydrophilic and biologically persistent trace organic chemicals (TrOCs). The high rejection by the FO membrane also led to accumulation of hydrophilic and biologically persistent TrOCs in the bioreactor, consequently increasing their concentration in the MF permeate. On the other hand, hydrophobic and readily biodegradable TrOCs were minimally detected in both MF and FO permeates, with no clear difference in the removal efficiencies between two processes. PMID:25966331

  15. Improving Settling Characteristics of Pure Oxygen Activated Sludge by Stripping of Carbon Dioxide.

    PubMed

    Kundral, Somshekhar; Mudragada, Ratnaji; Coro, Ernesto; Moncholi, Manny; Mora, Nelson; Laha, Shonali; Tansel, Berrin

    2015-06-01

    Increased microbial activity at high ambient temperatures can be problematic for secondary clarifiers and gravity concentrators due to carbon dioxide (CO2) production. Production of CO2 in gravity concentrators leads to septic conditions and poor solids separation. The CO2 production can also be corrosive for the concrete surfaces. Effectiveness of CO2 stripping to improve solids settling was investigated using the sludge volume index (SVI) as the indicator parameter. Carbon dioxide was stripped by aeration from the sludge samples. Results from the study show that aeration also increased the pH values in the mixed liquor while removing CO2 and improving sludge settling. After 10 minutes of aeration at a rate of 0.37 m3 air/m3 water/min, 90% CO2 stripping was achieved. Based on the 30 min settling tests, the SVI increased by 26±1% after CO2 stripping while the pH increased by 0.8±0.1 pH units. PMID:26459818

  16. Comparative study of wastewater treatment and nutrient recycle via activated sludge, microalgae and combination systems.

    PubMed

    Wang, Liang; Liu, Jinli; Zhao, Quanyu; Wei, Wei; Sun, Yuhan

    2016-07-01

    Algal-bacterial synergistic cultivation could be an optional wastewater treatment technology in temperate areas. In this study, a locally screened vigorous Chlorella strain was characterized and then it was used in a comparative study of wastewater treatment and nutrient recycle assessment via activated sludge (AS), microalgae and their combination systems. Chlorella sp. cultured with AS in light showed the best performance, in which case the removal efficiencies of COD, NH3-N and TP were 87.3%, 99.2% and 83.9%, respectively, within a short period of 1day. Algal-bacterial combination in light had the best settleability. Chlorella sp. contained biomass, could be processed to feed, fertilizer or fuel due to the improved quality (higher C/H/N) compared with sludge. PCR-DGGE analysis shows that two types of rhizobacteria, namely, Pseudomonas putida and Flavobacterium hauense were enriched in sludge when cultured with algae in light, serving as the basics for artificial consortium construction for improved wastewater treatment. PMID:26995615

  17. Effects of microwave irradiation on dewaterability and extracellular polymeric substances of waste activated sludge.

    PubMed

    Peng, Ge; Ye, Fenxia; Ye, Yangfang

    2013-03-01

    The effects of microwave irradiation on filterability and dewaterability of waste activated sludge measured by capillary suction time (CST) and dry solids in sludge cake were investigated. The results showed that the optimum irradiation time improved filterability, but that further increase of the time was detrimental. Dewaterability was enhanced significantly and increased with microwave time. Filterability and dewaterability were improved 25 to 28% and 1.3 times at the optimum times of 30 and 90 seconds for the sludge of 5 g total suspended solids (TSS)/L and 7 g TSS/L, respectively. The floc size decreased slightly. Loosely bound extracellular polymeric substances (LB-EPS) decreased under optimum time, but tightly bound extracellular polymeric substances did not change significantly after short irradiation time. The results implied that LB-EPS played a more important role in the observed changes of filterability and dewaterability and that the double-layered extracellular polymeric substances extraction method showed marked implications to dewaterability. PMID:23581243

  18. Biological short-chain fatty acids (SCFAs) production from waste-activated sludge affected by surfactant.

    PubMed

    Jiang, Su; Chen, Yinguang; Zhou, Qi; Gu, Guowei

    2007-07-01

    Short-chain fatty acids (SCFAs), the preferred carbon sources for biological nutrient removal, are the important intermediate products in sludge anaerobic fermentation. Sodium dodecylbenzene sulfonate (SDBS) is a widespread used surfactant, which can be easily found in waste-activated sludge (WAS). In this investigation, the effect of SDBS on SCFAs production from WAS was investigated, and the potential of using fermentative SCFAs to promote enhanced biological phosphorus removal (EBPR) was tested. Results showed that the total SCFAs production increased significantly in the presence of SDBS at room temperature. At fermentation time of 6 days, the maximum SCFAs was 2599.1mg chemical oxygen demand (COD)/L in the presence of SDBS 0.02g/g, whereas it was only 339.1mg (COD)/L in the absence of SDBS. The SCFAs produced in the case of SDBS 0.02g/g and fermentation time 6 days consisted of acetic acid (27.1%), propionic acid (22.8%), iso-valeric acid (20.1%), iso-butyric acid (11.9%), n-butyric acid (10.4%) and n-valeric acid (7.7%). It was found that during sludge anaerobic fermentation, the solubilization of sludge particulate organic-carbon and hydrolysis of solubilized substrate as well as acidification of hydrolyzed products were all increased in the presence of SDBS, while the methane formation was decreased, the SCFAs production was therefore remarkably improved. Further investigation showed that the production of SCFAs enhanced by SDBS was caused mainly by biological effects, rather than by chemical effects and SDBS decomposition. With the fermentative SCFAs as the main carbon source, the EBPR maintained high phosphorus removal efficiency ( approximately 97%). PMID:17499838

  19. Seasonal changes in the body size of two rotifer species living in activated sludge follow the Temperature-Size Rule

    PubMed Central

    Kiełbasa, Anna; Walczyńska, Aleksandra; Fiałkowska, Edyta; Pajdak-Stós, Agnieszka; Kozłowski, Jan

    2014-01-01

    Temperature-Size Rule (TSR) is a phenotypic body size response of ectotherms to changing temperature. It is known from the laboratory studies, but seasonal patterns in the field were not studied so far. We examined the body size changes in time of rotifers inhabiting activated sludge. We hypothesize that temperature is the most influencing parameter in sludge environment, leading sludge rotifers to seasonally change their body size according to TSR, and that oxygen content also induces the size response. The presence of TSR in Lecane inermis rotifer was tested in a laboratory study with two temperature and two food-type treatments. The effect of interaction between temperature and food was significant; L. inermis followed TSR in one food type only. The seasonal variability in the body sizes of the rotifers L. inermis and Cephalodella gracilis was estimated by monthly sampling and analyzed by multiple regression, in relation to the sludge parameters selected as the most influential by multivariate analysis, and predicted to alter rotifer body size (temperature and oxygen). L. inermis varied significantly in size throughout the year, and this variability is explained by temperature as predicted by the TSR, but not by oxygen availability. C. gracilis also varied in size, though this variability was explained by both temperature and oxygen. We suggest that sludge age acts as a mortality factor in activated sludge. It may have a seasonal effect on the body size of L. inermis and modify a possible effect of oxygen. Activated sludge habitat is driven by both biological processes and human regulation, yet its resident organisms follow general evolutionary rule as they do in other biological systems. The interspecific response patterns differ, revealing the importance of taking species-specific properties into account. Our findings are applicable to sludge properties enhancement through optimizing the conditions for its biological component. PMID:25558362

  20. Seasonal changes in the body size of two rotifer species living in activated sludge follow the Temperature-Size Rule.

    PubMed

    Kiełbasa, Anna; Walczyńska, Aleksandra; Fiałkowska, Edyta; Pajdak-Stós, Agnieszka; Kozłowski, Jan

    2014-12-01

    Temperature-Size Rule (TSR) is a phenotypic body size response of ectotherms to changing temperature. It is known from the laboratory studies, but seasonal patterns in the field were not studied so far. We examined the body size changes in time of rotifers inhabiting activated sludge. We hypothesize that temperature is the most influencing parameter in sludge environment, leading sludge rotifers to seasonally change their body size according to TSR, and that oxygen content also induces the size response. The presence of TSR in Lecane inermis rotifer was tested in a laboratory study with two temperature and two food-type treatments. The effect of interaction between temperature and food was significant; L. inermis followed TSR in one food type only. The seasonal variability in the body sizes of the rotifers L. inermis and Cephalodella gracilis was estimated by monthly sampling and analyzed by multiple regression, in relation to the sludge parameters selected as the most influential by multivariate analysis, and predicted to alter rotifer body size (temperature and oxygen). L. inermis varied significantly in size throughout the year, and this variability is explained by temperature as predicted by the TSR, but not by oxygen availability. C. gracilis also varied in size, though this variability was explained by both temperature and oxygen. We suggest that sludge age acts as a mortality factor in activated sludge. It may have a seasonal effect on the body size of L. inermis and modify a possible effect of oxygen. Activated sludge habitat is driven by both biological processes and human regulation, yet its resident organisms follow general evolutionary rule as they do in other biological systems. The interspecific response patterns differ, revealing the importance of taking species-specific properties into account. Our findings are applicable to sludge properties enhancement through optimizing the conditions for its biological component. PMID:25558362

  1. Updated activated sludge model number 1 parameter values for improved prediction of nitrogen removal in activated sludge processes: validation at 13 full-scale plants.

    PubMed

    Choubert, Jean-Marc; Stricker, Anne-Emmanuelle; Marquot, Aurélien; Racault, Yvan; Gillot, Sylvie; Héduit, Alain

    2009-01-01

    The Activated Sludge Model number 1 (ASM1) is the main model used in simulation projects focusing on nitrogen removal. Recent laboratory-scale studies have found that the default values given 20 years ago for the decay rate of nitrifiers and for the heterotrophic biomass yield in anoxic conditions were inadequate. To verify the relevance of the revised parameter values at full scale, a series of simulations were carried out with ASM1 using the original and updated set of parameters at 20 degrees C and 10 degrees C. The simulation results were compared with data collected at 13 full-scale nitrifying-denitrifying municipal treatment plants. This work shows that simulations using the original ASM1 default parameters tend to overpredict the nitrification rate and underpredict the denitrification rate. The updated set of parameters allows more realistic predictions over a wide range of operating conditions. PMID:19860142

  2. Metagenomic analyses reveal phylogenetic diversity of carboxypeptidase gene sequences in activated sludge of a wastewater treatment plant in Shanghai, China.

    PubMed

    Jin, Hao; Li, Bailin; Peng, Xu; Chen, Lanming

    2014-01-01

    Activated sludge of wastewater treatment plants carries a diverse microflora. However, up to 80-90 % of microorganisms in activated sludge cannot be cultured by current laboratory techniques, leaving an enzyme reservoir largely unexplored. In this study, we investigated carboxypeptidase diversity in activated sludge of a wastewater treatment plant in Shanghai, China, by a culture-independent metagenomic approach. Three sets of consensus degenerate hybrid oligonucleotide primers (CODEHOPs) targeting conserved domains of public carboxypeptidases have been designed to amplify carboxypeptidase gene sequences in the metagenomic DNA of activated sludge by PCR. The desired amplicons were evaluated by carboxypeptidase sequence clone libraries and phylogenetic analyses. We uncovered a significant diversity of carboxypeptidases present in the activated sludge. Deduced carboxypeptidase amino acid sequences (127-208 amino acids) were classified into three distinct clusters, α, β, and γ. Sequences belonging to clusters α and β shared 58-97 % identity to known carboxypeptidase sequences from diverse species, whereas sequences in the cluster γ were remarkably less related to public carboxypeptidase homologous in the GenBank database, strongly suggesting that novel carboxypeptidase families or microbial niches exist in the activated sludge. We also observed numerous carboxypeptidase sequences that were much closer to those from representative strains present in industrial and sewage treatment and bioremediation. Thermostable and halotolerant carboxypeptidase sequences were also detected in clusters α and β. Coexistence of various carboxypeptidases is evidence of a diverse microflora in the activated sludge, a feature suggesting a valuable gene resource to be further explored for biotechnology application. PMID:24860282

  3. [Start-up and process control of a pilot-scale Anammox bioreactor at ambient temperature].

    PubMed

    Tang, Chongjian; Zheng, Ping; Chen, Jianwei; Chen, Xiaoguang; Zhou, Shangxing; Ding, Gesheng

    2009-03-01

    Start-up and process control of a pilot-scale anaerobic ammonium-oxidizing (Anammox) bioreactor were studied at ambient temperature. Inoculated with a mixture of nitrification-denitrification sludge, nitritation sludge, anaerobic floc sludge and anaerobic granular sludge, the pilot-scale Anammox bioreactor was successfully started up within 255 days at 5 degrees C-27 degrees C. The nitrogen removal rate reached 1.30 kg/(m3 x d). Three facets were taken into account to facilitate the process initiation. First, in terms of alkalization in Anammox, influent pH was kept at about 6.8. Besides, nitrite concentration was kept as low as 13-36 mg/L. Finally, 2% (volumetric ratio) of Anammox sludge from lab-scale bioreactors was supplemented to the pilot-scale one. PMID:19621582

  4. Contribution of stratified extracellular polymeric substances to the gel-like and fractal structures of activated sludge.

    PubMed

    Yuan, D Q; Wang, Y L; Feng, J

    2014-06-01

    The gel-like and fractal structures of activated sludge (AS) before and after extracellular polymeric substances (EPS) extraction as well as different EPS fractions were investigated. The contributions of individual components in different EPS fractions to the gel-like behavior of sludge samples by enzyme treatment were examined as well. The centrifugation and ultrasound method was employed to stratify the EPS into slime, loosely and tightly bound EPS (LB- and TB-EPS). It was observed that all samples behaved as weak gels with weak-link. TB-EPS and AS after LB-EPS extraction showed the strongest elasticity in higher concentrations and highest mass fractal dimension, which may indicate the key role of TB-EPS in the gel-like and fractal structures of the sludge. Effects of protease or amylase on the gel-like property of sludge samples differed in the presence of different EPS fractions. PMID:24651018

  5. Occurrence, distribution, and potential influencing factors of sewage sludge components derived from nine full-scale wastewater treatment plants of Beijing, China.

    PubMed

    Wang, Xu; Li, Meiyan; Liu, Junxin; Qu, Jiuhui

    2016-07-01

    Millions of tons of waste activated sludge (WAS) produced from biological wastewater treatment processes cause severe adverse environmental consequences. A better understanding of WAS composition is thus very critical for sustainable sludge management. In this work, the occurrence and distribution of several fundamental sludge constituents were explored in WAS samples from nine full-scale wastewater treatment plants (WWTPs) of Beijing, China. Among all the components investigated, active heterotrophic biomass was dominant in the samples (up to 9478mg/L), followed by endogenous residues (6736mg/L), extracellular polymeric substances (2088mg/L), and intracellular storage products (464mg/L) among others. Moreover, significant differences (p<0.05) were observed in composition profiles of sludge samples among the studied WWTPs. To identify the potential parameters affecting the variable fractions of sludge components, wastewater source as well as design and operational parameters of WWTPs were studied using statistical methods. The findings indicated that the component fraction of sewage sludge depends more on wastewater treatment alternatives than on wastewater characteristics among other parameters. A principal component analysis was conducted, which further indicated that there was a greater proportion of residual inert biomass in the sludge produced by the combined system of the conventional anaerobic/anoxic/oxic process and a membrane bioreactor. Additionally, a much longer solids retention time was also found to influence the sludge composition and induce an increase in both endogenous inert residues and extracellular polymeric substances in the sludge. PMID:27372138

  6. Organics removal from landfill leachate and activated sludge production in SBR reactors

    SciTech Connect

    Klimiuk, Ewa; Kulikowska, Dorota . E-mail: dorotak@uwm.edu.pl

    2006-07-01

    This study is aimed at estimating organic compounds removal and sludge production in SBR during treatment of landfill leachate. Four series were performed. At each series, experiments were carried out at the hydraulic retention time (HRT) of 12, 6, 3 and 2 d. The series varied in SBR filling strategies, duration of the mixing and aeration phases, and the sludge age. In series 1 and 2 (a short filling period, mixing and aeration phases in the operating cycle), the relationship between organics concentration (COD) in the leachate treated and HRT was pseudo-first-order kinetics. In series 3 (with mixing and aeration phases) and series 4 (only aeration phase) with leachate supplied by means of a peristaltic pump for 4 h of the cycle (filling during reaction period) - this relationship was zero-order kinetics. Activated sludge production expressed as the observed coefficient of biomass production (Y {sub obs}) decreased correspondingly with increasing HRT. The smallest differences between reactors were observed in series 3 in which Y {sub obs} was almost stable (0.55-0.6 mg VSS/mg COD). The elimination of the mixing phase in the cycle (series 4) caused the Y {sub obs} to decrease significantly from 0.32 mg VSS/mg COD at HRT 2 d to 0.04 mg VSS/mg COD at HRT 12 d. The theoretical yield coefficient Y accounted for 0.534 mg VSS/mg COD (series 1) and 0.583 mg VSS/mg COD (series 2). In series 3 and 4, it was almost stable (0.628 mg VSS/mg COD and 0.616 mg VSS/mg COD, respectively). After the elimination of the mixing phase in the operating cycle, the specific biomass decay rate increased from 0.006 d{sup -1} (series 3) to 0.032 d{sup -1} (series 4). The operating conditions employing mixing/aeration or only aeration phases enable regulation of the sludge production. The SBRs operated under aerobic conditions are more favourable at a short hydraulic retention time. At long hydraulic retention time, it can lead to a decrease in biomass concentration in the SBR as a result of

  7. Economical evaluation of sludge reduction and characterization of effluent organic matter in an alternating aeration activated sludge system combining ozone/ultrasound pretreatment.

    PubMed

    Yang, Shan-Shan; Guo, Wan-Qian; Chen, Yi-Di; Wu, Qing-Lian; Luo, Hai-Chao; Peng, Si-Mai; Zheng, He-Shan; Feng, Xiao-Chi; Zhou, Xu; Ren, Nan-Qi

    2015-02-01

    An ozone/ultrasound lysis-cryptic growth technology combining a continuous flow anaerobic-anoxic-microaerobic-aerobic (AAMA+O3/US) system was investigated. Techno-economic evaluation and sludge lyses return ratio (r) optimization of this AAMA+O3/US system were systematically and comprehensively discussed. Economic assessment demonstrated that this AAMA+O3/US system with r of 30% (AAMA+O3/US2# system) was more economically feasible that can give a 14.04% saving of costs. In addition to economic benefits, a 55.08% reduction in sludge production, and respective 21.17% and 5.45% increases in TN and TP removal efficiencies were observed in this AAMA+O3/US2# system. Considering the process performances and economic benefits, r of 30% in AAMA+O3/US2# system was recommended. Excitation-emission matrix and Fourier transform infrared spectra analyses also proved that less refractory soluble microbial products were generated from AAMA+O3/US2# system. Improvement in 2,3,5-triphenyltetrazolium chloride electron transport system (TTC-ETS) activity in AAMA+O3/US2# further indicated that a lower sludge lyses return ratio stimulated the microbial activity. PMID:25490102

  8. Chemically coupled microwave and ultrasonic pre-hydrolysis of pulp and paper mill waste-activated sludge: effect on sludge solubilisation and anaerobic digestion.

    PubMed

    Tyagi, Vinay Kumar; Lo, Shang-Lien; Rajpal, Ankur

    2014-05-01

    The effects of alkali-enhanced microwave (MW; 50-175 °C) and ultrasonic (US) (0.75 W/mL, 15-60 min) pretreatments, on solubilisation and subsequent anaerobic digestion efficiency of pulp and paper mill waste-activated sludge, were investigated. Improvements in total chemical oxygen demand and volatile suspended solids (VSS) solubilisation were limited to 33 and 39 % in MW pretreatment only (175 °C). It reached 78 and 66 % in combined MW-alkali pretreatment (pH 12 + 175 °C), respectively. Similarly, chemical oxygen demand and VSS solubilisation were 58 and 37 % in US pretreatment alone (60 min) and it improved by 66 and 49 % after US-alkali pretreatment (pH 12 + 60 min), respectively. The biogas yield for US 60 min-alkali (pH 12)-pretreated sludge was significantly improved by 47 and 20 % over the control and US 60 reactors, respectively. The biogas generation for MW (150 °C)-alkali (pH 12)-pretreated sludge was only 6.3 % higher than control; however, it was 8.3 % lower than the MW (150 °C) reactor, which was due to the inhibition of anaerobic activity under harsh thermal-alkali treatment condition. PMID:24488518

  9. Waste activated sludge treatment based on temperature staged and biologically phased anaerobic digestion system.

    PubMed

    Yu, Jingwen; Zheng, Mingxia; Tao, Tao; Zuo, Jiane; Wang, Kaijun

    2013-10-01

    The concept of temperature staged and biological phased (TSBP) was proposed to enhance the performance of waste-activated sludge anaerobic digestion. Semi-continuous experiments were used to investigate the effect of temperature (35 to 70 degrees C) as well as the hydraulic retention time (HRT) (2, 4 and 6 days) on the acidogenic phase. The results showed that the solubilization degree of waste-activated sludge increased from 14.7% to 30.1% with temperature increasing from 35 to 70 degrees C, while the acidification degree was highest at 45 degrees C (17.6%), and this was quite different from the temperature impact on hydrolysis. Compared with HRT of 2 and 6 days, 4 days was chosen as the appropriate HRT because of its relatively high solubilization degree (24.6%) and acidification degree (20.1%) at 45 degrees C. The TSBP system combined the acidogenic reactor (45 degrees C, 4 days) with the methanogenic reactor (35 degrees C, 16 days) and the results showed 84.8% and 11.4% higher methane yield and volatile solid reduction, respectively, compared with that of the single-stage anaerobic digestion system with HRT of 20 days at 35 degrees C. Moreover, different microbial morphologies were observed in the acidogenic- and methanogenic-phase reactors, which resulted from the temperature control and HRT adjustment. All the above results indicated that 45 degrees C was the optimum temperature to inhibit the activity of methanogenic bacteria in the acidogenic phase, and temperature staging and phase separation was thus accomplished. The advantages of the TSBP process were also confirmed by a full-scale waste-activated sludge anaerobic digestion project which was an energy self-sufficient system. PMID:24494492

  10. Bioreactors Addressing Diabetes Mellitus

    PubMed Central

    Minteer, Danielle M.; Gerlach, Jorg C.

    2014-01-01

    The concept of bioreactors in biochemical engineering is a well-established process; however, the idea of applying bioreactor technology to biomedical and tissue engineering issues is relatively novel and has been rapidly accepted as a culture model. Tissue engineers have developed and adapted various types of bioreactors in which to culture many different cell types and therapies addressing several diseases, including diabetes mellitus types 1 and 2. With a rising world of bioreactor development and an ever increasing diagnosis rate of diabetes, this review aims to highlight bioreactor history and emerging bioreactor technologies used for diabetes-related cell culture and therapies. PMID:25160666

  11. Dynamic Compression Effects on Immature Nucleus Pulposus: a Study Using a Novel Intelligent and Mechanically Active Bioreactor

    PubMed Central

    Li, Pei; Gan, Yibo; Wang, Haoming; Zhang, Chengmin; Wang, Liyuan; Xu, Yuan; Song, Lei; Li, Songtao; Li, Sukai; Ou, Yangbin; Zhou, Qiang

    2016-01-01

    Background: Previous cell culture and animal in vivo studies indicate the obvious effects of mechanical compression on disc cell biology. However, the effects of dynamic compression magnitude, frequency and duration on the immature nucleus pulposus (NP) from an organ-cultured disc are not well understood. Objective: To investigate the effects of a relatively wide range of compressive magnitudes, frequencies and durations on cell apoptosis and matrix composition within the immature NP using an intelligent and mechanically active bioreactor. Methods: Discs from the immature porcine were cultured in a mechanically active bioreactor for 7 days. The discs in various compressive magnitude groups (0.1, 0.2, 0.4, 0.8 and 1.3 MPa at a frequency of 1.0 Hz for 2 hours), frequency groups (0.1, 0.5, 1.0, 3.0 and 5.0 Hz at a magnitude of 0.4 MPa for 2 hours) and duration groups (1, 2, 4 and 8 hours at a magnitude of 0.4 MPa and frequency of 1.0 Hz) experienced dynamic compression once per day. Discs cultured without compression were used as controls. Immature NP samples were analyzed using the TUNEL assay, histological staining, glycosaminoglycan (GAG) content measurement, real-time PCR and collagen II immunohistochemical staining. Results: In the 1.3 MPa, 5.0 Hz and 8 hour groups, the immature NP showed a significantly increase in apoptotic cells, a catabolic gene expression profile with down-regulated matrix molecules and up-regulated matrix degradation enzymes, and decreased GAG content and collagen II deposition. In the other compressive magnitude, frequency and duration groups, the immature NP showed a healthier status regarding NP cell apoptosis, gene expression profile and matrix production. Conclusion: Cell apoptosis and matrix composition within the immature NP were compressive magnitude-, frequency- and duration-dependent. The relatively high compressive magnitude or frequency and long compressive duration are not helpful for maintai