NASA's Next Generation Space Geodesy Network

NASA Technical Reports Server (NTRS)

Desai, S. D.; Gross, R. S.; Hilliard, L.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry, J. F.; Merkowitz, S. M.; Murphy, D.; Noll, C. E.;

The contribution of engineering surveys by means of GPS to the determination of crustal movements in Istanbul

NASA Astrophysics Data System (ADS)

Özyaşar, M.; Özlüdemir, M. T.

2011-06-01

Global Navigation Satellite Systems (GNSS) are space based positioning techniques and widely used in geodetic applications. Geodetic networking accomplished by engineering surveys constitutes one of these tasks. Geodetic networks are used as the base of all kinds of geodetic implementations, Co from the cadastral plans to the relevant surveying processes during the realization of engineering applications. Geodetic networks consist of control points positioned in a defined reference frame. In fact, such positional information could be useful for other studies as well. One of such fields is geodynamic studies that use the changes of positions of control stations within a network in a certain time period to understand the characteristics of tectonic movements. In Turkey, which is located in tectonically active zones and struck by major earthquakes quite frequently, the positional information obtained in engineering surveys could be very useful for earthquake related studies. For this purpose, a GPS (Global Positioning System) network of 650 stations distributed over Istanbul (Istanbul GPS Triangulation Network; abbreviated IGNA) covering the northern part of the North Anatolian Fault Zone (NAFZ) was established in 1997 and measured in 1999. From 1998 to 2004, the IGNA network was extended to 1888 stations covering an area of about 6000 km2, the whole administration area of Istanbul. All 1888 stations within the IGNA network were remeasured in 2005. In these two campaigns there existed 452 common points, and between these two campaigns two major earthquakes took place, on 17 August and 12 November 1999 with a Richter scale magnitude of 7.4 and 7.2, respectively. Several studies conducted for estimating the horizontal and vertical displacements as a result of these earthquakes on NAFZ are discussed in this paper. In geodynamic projects carried out before the earthquakes in 1999, an annual average velocity of 2-2.5 cm for the stations along the NAFZ were estimated. Studies carried out using GPS observations in the same area after these earthquakes indicated that point displacements vary depending on their distance to the epicentres of the earthquakes. But the directions of point displacements are similar. The results obtained through the analysis of the IGNA network also show that there is a common trend in the directions of point displacements in the study area. In this paper, the past studies about the tectonics of Marmara region are summarised and the results of the displacement analysis on the IGNA network are discussed.

NASA's Next Generation Space Geodesy Program

NASA Technical Reports Server (NTRS)

Pearlman, M. R.; Frey, H. V.; Gross, R. S.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry J. F.; Merkowitz, S. M.; Noll, C. E.; Pavilis, E. C.;

NASA's Next Generation Space Geodesy Program

NASA Technical Reports Server (NTRS)

Merkowitz, S. M.; Desai, S. D.; Gross, R. S.; Hillard, L. M.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry, J. F.; Murphy, D.; Noll, C. E.;

Next Generation NASA Initiative for Space Geodesy

NASA Technical Reports Server (NTRS)

Merkowitz, S. M.; Desai, S.; Gross, R. S.; Hilliard, L.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry J. F.; Murphy, D.; Noll, C. E.;

First-order design of geodetic networks using the simulated annealing method

NASA Astrophysics Data System (ADS)

Berné, J. L.; Baselga, S.

2004-09-01

The general problem of the optimal design for a geodetic network subject to any extrinsic factors, namely the first-order design problem, can be dealt with as a numeric optimization problem. The classic theory of this problem and the optimization methods are revised. Then the innovative use of the simulated annealing method, which has been successfully applied in other fields, is presented for this classical geodetic problem. This method, belonging to iterative heuristic techniques in operational research, uses a thermodynamical analogy to crystalline networks to offer a solution that converges probabilistically to the global optimum. Basic formulation and some examples are studied.

Kinematics, seismotectonics and seismic potential of the eastern sector of the European Alps from GPS and seismic deformation data

NASA Astrophysics Data System (ADS)

Serpelloni, E.; Vannucci, G.; Anderlini, L.; Bennett, R. A.

2016-10-01

We present a first synoptic view of the seismotectonics and kinematics of the eastern sector of the European Alps using geodetic and seismological data. The study area marks the boundary between the Adriatic and the Eurasian plates, through a wide zone of deformation including a variety of tectonic styles within a complex network of crustal and lithospheric faults. A new dense GPS velocity field, new focal mechanisms and seismic catalogues, with uniformly re-calibrated magnitudes (from 1005), are used to estimate geodetic and seismic deformation rates and to develop interseismic kinematic and fault locking models. Kinematic indicators from seismological and geodetic data are remarkably consistent at different spatial scales. In addition to large-scale surface motion, GPS velocities highlight more localized deformation features revealing a complex configuration of interacting tectonic blocks, for which new constraints are provided in this work accounting for elastic strain build up at faults bonding rotating blocks. The geodetic and seismological data highlight two belts of higher deformation rates running WSW-ENE along the Eastern Southern Alps (ESA) in Italy and E-W in Slovenia, where deformation is more distributed. The highest geodetic strain-rates are observed in the Montello-Cansiglio segment of the ESA thrust front, for which the higher density of the GPS network provides indications of limited interseismic locking. Most of the dextral shear between the Eastern Southern Alps and the Eastern Alps blocks is accommodated along the Fella-Sava fault rather than the Periadriatic fault. In northern Croatia and Slovenia geodetic and seismological data allow constraining the kinematics of the active structures bounding the triangular-shaped region encompassing the Sava folds, which plays a major role in accommodating the transition from Adria- to Pannonian-like motion trends. The analysis of the seismic and geodetic moment rates provides new insights into the seismic potential along the ESA front.

Seismology and space-based geodesy

NASA Technical Reports Server (NTRS)

Tralli, David M.; Tajima, Fumiko

1993-01-01

The potential of space-based geodetic measurement of crustal deformation in the context of seismology is explored. The achievements of seismological source theory and data analyses, mechanical modeling of fault zone behavior, and advances in space-based geodesy are reviewed, with emphasis on realizable contributions of space-based geodetic measurements specifically to seismology. The fundamental relationships between crustal deformation associated with an earthquake and the geodetically observable data are summarized. The response and spatial and temporal resolution of the geodetic data necessary to understand deformation at various phases of the earthquake cycle is stressed. The use of VLBI, SLR, and GPS measurements for studying global geodynamics properties that can be investigated to some extent with seismic data is discussed. The potential contributions of continuously operating strain monitoring networks and globally distributed geodetic observatories to existing worldwide modern digital seismographic networks are evaluated in reference to mutually addressable problems in seismology, geophysics, and tectonics.

Modeling and Simulation Network Data Standards

DTIC Science & Technology

2011-09-30

COMBATXXI Movement Logger Data Output Dictionary. Field # Geocentric Coordinates (GCC) Heading Geodetic Coordinates (GDC) Heading Universal...B-8 Field # Geocentric Coordinates (GCC) Heading Geodetic Coordinates (GDC) Heading Universal Transverse Mercator (UTM) Heading...FKSM Fort Knox Supplemental Material FM field manual GCC geocentric coordinates GDC geodetic coordinates GIG global information grid

International VLBI Service for Geodesy and Astrometry 2004 Annual Report

NASA Technical Reports Server (NTRS)

Behrend, Dirk (Editor); Baver, Karen D. (Editor)

2005-01-01

Contents include the following: Combination Studies using the Cont02 Campaign. Coordinating Center report. Analysis coordinator report. Network coordinator report. IVS Technology coordinator report. Algonquin Radio observatory. Fortaleza Station report for 2004. Gilmore Creek Geophysical Observatory. Goddard Geophysical and Astronomical observatory. Hartebeesthoek Radio Astronomy Observatory (HartRAO). Hbart, Mt Pleasant, station report for 2004. Kashima 34m Radio Telescope. Kashima and Koganei 11-m VLBI Stations. Kokee Park Geophysical Observatory. Matera GGS VLBI Station. The Medicina Station status report. Report of the Mizusawa 10m Telescope. Noto Station Activity. NYAL Ny-Alesund 20 metre Antenna. German Antarctic receiving Station (GARS) O'higgins. The IVS network station Onsala space Observatory. Sheshan VLBI Station report for 2004. 10 Years of Geodetic Experiments at the Simeiz VLBI Station. Svetloe RAdio Astronomical Observatory. JARE Syowa Station 11-m Antenna, Antarctica. Geodetic Observatory TIGO in Concepcion. Tsukuba 32-m VLBI Station. Nanshan VLBI Station Report. Westford Antenna. Fundamental-station Wettzell 20m Radiotelescope. Observatorio Astroonomico Nacional Yebes. Yellowknife Observatory. The Bonn Geodetic VLBI Operation Center. CORE Operation Center Report. U.S. Naval Observatory Operation Center. The Bonn Astro/Geo Mark IV Correlator.

Satellite-tracking and earth-dynamics research programs. [geodetic and geophysical investigations and atmospheric research using satellite drag data

NASA Technical Reports Server (NTRS)

1972-01-01

Satellite tracking and earth dynamics research programs are discussed. Geodetic and geophysical investigations are reported along with atmospheric research using satellite drag data. Satellite tracking network functions and support groups which are discussed include: network operations, communications, data-services division, moonwatch, and programming group.

Seismic and Geodetic Monitoring of the Nicoya, Costa Rica, Seismic Gap

NASA Astrophysics Data System (ADS)

Protti, M.; Gonzalez, V.; Schwartz, S.; Dixon, T.; Kato, T.; Kaneda, Y.; Simila, G.; Sampson, D.

2007-05-01

The Nicoya segment of the Middle America Trench has been recognized as a mature seismic gap with potential to generate a large earthquake in the near future (it ruptured with large earthquakes in 1853, 1900 and 1950). Low level of background seismicity and fast crustal deformation of the forearc are indicatives of strong coupling along the plate interface. Given its high seismic potential, the available data and especially the fact that the Nicoya peninsula extends over large part of the rupture area, this gap was selected as one of the two sites for a MARGINS-SEIZE experiment. With the goal of documenting the evolution of loading and stress release along this seismic gap, an international effort involving several institutions from Costa Rica, the United States and Japan is being carried out for over a decade in the region. This effort involves the installation of temporary and permanent seismic and geodetic networks. The seismic network includes short period, broad band and strong motion instruments. The seismic monitoring has provided valuable information on the geometry and characteristics of the plate interface. The geodetic network includes temporary and permanent GPS stations as well as surface and borehole tiltmeters. The geodetic networks have helped quantify the extend and degree of coupling. A continuously recording, three- station GPS network on the Nicoya Peninsula, Costa Rica, recorded what we believe is the first slow slip event observed along the plate interface of the Costa Rica subduction zone. We will present results from these monitoring networks. Collaborative international efforts are focused on expanding these seismic and geodetic networks to provide improved resolution of future creep events, to enhanced understanding of the mechanical behavior of the Nicoya subduction segment of the Middle American Trench and possibly capture the next large earthquake and its potential precursor deformation.

VERA Geodetic Activities

NASA Technical Reports Server (NTRS)

Jike, Takaaki; Tamura, Yoshiaki; Shizugami, Makoto

2013-01-01

This report briefly describes the geodetic activities of VERA in the year 2012. The regular geodetic observations are carried out both in K- and S/X-bands. The frequency of regular observations is three times a month-twice for the VERA internal observations in K-band. The networks of the S/X sessions are JADE of GSI and IVS-T2. The raw data of the T2 and JADE sessions are electronically transferred to the Bonn, Haystack, and GSI correlators via Internet. Gravimetric observations are carried out at the VERA stations. An SG was installed at Mizusawa and placed in the vicinity of the VERA antenna in order to monitor vertical displacement at the end of 2008, and the observations continued throughout the year. Also at the VERA-Ishigakijima station, continuous operation of the SG started in 2012. The crustal movements generated by the 2011 earthquake off the Pacific coast of Tohoku continued during 2012, and displacement of the VERA-Mizusawa position by post-seismic creeping continued.

International global network of fiducial stations: Scientific and implementation issues

NASA Astrophysics Data System (ADS)

1991-11-01

In this report, an ad hoc panel of the National Research Council's Committee on Geodesy, Board of Earth Sciences and Resources (1) evaluates the scientific importance of a global network of fiducial sites, monitored very precisely, using a combination of surface- and space-geodetic techniques; (2) examines strategies for implementing and operating such a network; and (3) assesses whether such a network would provide a suitable global infrastructure for geodetic and other geophysical systems of the next century. The panel concludes that a global network of fiducial sites would be a valuable tool for addressing global change issues and play a critical role in providing a reference frame for scientific Earth missions. The panel suggests that existing global networks be integrated and anticipates that such a network would grow from about 30 to the ultimate size of about 200 fiducial sites. It is noted that such a global network will provide a long-term infrastructure for geodetic and geophysical studies. The panel expects that these fiducial sites would evolve into terrestrial observatories or laboratories that would permit more comprehensive studies of the Earth than those now possible.

International global network of fiducial stations: Scientific and implementation issues

NASA Technical Reports Server (NTRS)

1991-01-01

In this report, an ad hoc panel of the National Research Council's Committee on Geodesy, Board of Earth Sciences and Resources (1) evaluates the scientific importance of a global network of fiducial sites, monitored very precisely, using a combination of surface- and space-geodetic techniques; (2) examines strategies for implementing and operating such a network; and (3) assesses whether such a network would provide a suitable global infrastructure for geodetic and other geophysical systems of the next century. The panel concludes that a global network of fiducial sites would be a valuable tool for addressing global change issues and play a critical role in providing a reference frame for scientific Earth missions. The panel suggests that existing global networks be integrated and anticipates that such a network would grow from about 30 to the ultimate size of about 200 fiducial sites. It is noted that such a global network will provide a long-term infrastructure for geodetic and geophysical studies. The panel expects that these fiducial sites would evolve into terrestrial observatories or laboratories that would permit more comprehensive studies of the Earth than those now possible.

Basic research and data analysis for the national geodetic satellite program and for the earth and ocean physics applications program

NASA Technical Reports Server (NTRS)

1974-01-01

Activities related to the National Geodetic Satellite Program are reported and include a discussion of Ohio State University's OSU275 set of tracking station coordinates and transformation parameters, determination of network distortions, and plans for data acquisition and processing. The problems encountered in the development of the LAGEOS satellite are reported in an account of activities related to the Earth and Ocean Physics Applications Program. The LAGEOS problem involves transmission and reception of the laser pulse designed to make accurate determinations of the earth's crustal and rotational motions. Pulse motion, ephemeris, arc range measurements, and accuracy estimates are discussed in view of the problem. Personnel involved in the two programs are also listed, along with travel activities and reports published to date.

How well can online GPS PPP post-processing services be used to establish geodetic survey control networks?

NASA Astrophysics Data System (ADS)

Ebner, R.; Featherstone, W. E.

2008-09-01

Establishing geodetic control networks for subsequent surveys can be a costly business, even when using GPS. Multiple stations should be occupied simultaneously and post-processed with scientific software. However, the free availability of online GPS precise point positioning (PPP) post-processing services offer the opportunity to establish a whole geodetic control network with just one dual-frequency receiver and one field crew. To test this idea, we compared coordinates from a moderate-sized (~550 km by ~440 km) geodetic network of 46 points over part of south-western Western Australia, which were processed both with the Bernese v5 scientific software and with the CSRS (Canadian Spatial Reference System) PPP free online service. After rejection of five stations where the antenna type was not recognised by CSRS, the PPP solutions agreed on average with the Bernese solutions to 3.3 mm in east, 4.8 mm in north and 11.8 mm in height. The average standard deviations of the Bernese solutions were 1.0 mm in east, 1.2 mm in north and 6.2 mm in height, whereas for CSRS they were 3.9 mm in east, 1.9 mm in north and 7.8 mm in height, reflecting the inherently lower precision of PPP. However, at the 99% confidence level, only one CSRS solution was statistically different to the Bernese solution in the north component, due to a data interruption at that site. Nevertheless, PPP can still be used to establish geodetic survey control, albeit with a slightly lower quality because of the larger standard deviations. This approach may be of particular benefit in developing countries or remote regions, where geodetic infrastructure is sparse and would not normally be established without this approach.

A Solution to Bring the National Astronomical-Geodetic Network from S/42 System to WGS-84 System

NASA Astrophysics Data System (ADS)

Radu, Ion

In the framework of a Romanian-Bulgarian cooperation, the Military Astronomical Observatory Bucharest integrated GPS measurements with points in the Southern zone of the national geodetic network. Molodensky's, Zhogolovich's and Ihde's relations were used to pass from S/42 system to WGS-84 system. Six variants for the choice of common points were considered.

Monitoring Coral Growth - the Dichotomy Between Underwater Photogrammetry and Geodetic Control Network

NASA Astrophysics Data System (ADS)

Neyer, F.; Nocerino, E.; Gruen, A.

2018-05-01

Creating 3-dimensional (3D) models of underwater scenes has become a common approach for monitoring coral reef changes and its structural complexity. Also in underwater archeology, 3D models are often created using underwater optical imagery. In this paper, we focus on the aspect of detecting small changes in the coral reef using a multi-temporal photogrammetric modelling approach, which requires a high quality control network. We show that the quality of a good geodetic network limits the direct change detection, i.e., without any further registration process. As the photogrammetric accuracy is expected to exceed the geodetic network accuracy by at least one order of magnitude, we suggest to do a fine registration based on a number of signalized points. This work is part of the Moorea Island Digital Ecosystem Avatar (IDEA) project that has been initiated in 2013 by a group of international researchers (https://mooreaidea.ethz.ch/).

Evidence for possible relation between local irregularities in the horizondal deformation field and microseismic activity of the Mygdonian basin(Northern Greece)

NASA Astrophysics Data System (ADS)

Contadakis, M. E.; Leventakis, G.-A. N.

1992-12-01

Geodetic methods have been proved very useful tools for the detection and monitoring of the earth crustal deformation. Using the repeated measurements in the decade 1979-1990 of the 16-point trigonometric network, located in the seismic active area of the lake Volvi in Northern Greece, a continuous strain field was determined for the area and for each epoch of the corresponding surveys. The dominant characteristic of the deformation field of the area relates, in a way, to the system of the surface faults, which appeared after the string earthquake of June 21, 1978. In addition, there is local as well as time variation of the strain field which is well correlated with the microseismic activity of the area. That is, although there is a general tendency of a N-S horizontal extension in accordance with the direction of the stress field of the area, regions of contraction appear in places where microseismic activity has taken place before the epochs of the respective survey. A few shocks in these region, for which reliable fault plane solutions could be defined by Scordilis on 1985,show focal mechanisms conformable to the geodetic results. Seismicity and fault plane solutions, based on a micro-earthquake study of the region during March and April of 1984 by Hatzfeld et al. with the help of a temporary network of 29 portable stations shows a rather complex pattern. The proposed model for the formation and the evolution of a complex graben system conform qualitatively to the geodetic results

The Software Correlator of the Chinese VLBI Network

NASA Technical Reports Server (NTRS)

Zheng, Weimin; Quan, Ying; Shu, Fengchun; Chen, Zhong; Chen, Shanshan; Wang, Weihua; Wang, Guangli

2010-01-01

The software correlator of the Chinese VLBI Network (CVN) has played an irreplaceable role in the CVN routine data processing, e.g., in the Chinese lunar exploration project. This correlator will be upgraded to process geodetic and astronomical observation data. In the future, with several new stations joining the network, CVN will carry out crustal movement observations, quick UT1 measurements, astrophysical observations, and deep space exploration activities. For the geodetic or astronomical observations, we need a wide-band 10-station correlator. For spacecraft tracking, a realtime and highly reliable correlator is essential. To meet the scientific and navigation requirements of CVN, two parallel software correlators in the multiprocessor environments are under development. A high speed, 10-station prototype correlator using the mixed Pthreads and MPI (Massage Passing Interface) parallel algorithm on a computer cluster platform is being developed. Another real-time software correlator for spacecraft tracking adopts the thread-parallel technology, and it runs on the SMP (Symmetric Multiple Processor) servers. Both correlators have the characteristic of flexible structure and scalability.

The PBO Nucleus: Integration of the Existing Continuous GPS Networks in the Western U.S.

NASA Astrophysics Data System (ADS)

Blume, F.; Anderson, G.; Freymueller, J. T.; Herring, T. A.; Melbourne, T. I.; Murray, M. H.; Prescott, W. H.; Smith, R. B.; Wernicke, B.

2004-12-01

Tectonic and earthquake research in the US has experienced a quiet revolution over the last decade precipitated by the recognition that slow-motion faulting events can both trigger and be triggered by regular earthquakes. Transient motion has now been found in essentially all tectonic environments, and the detection and analysis of such events is the first-order science target of the EarthScope Project. Because of this and a host of other fundamental tectonics questions that can be answered only with long-duration geodetic time series, the incipient 1400-station EarthScope Plate Boundary Observatory (PBO) network has been designed to leverage 432 existing continuous GPS stations whose measurements extend back over a decade. The irreplaceable recording history of these stations will accelerate EarthScope scientific return by providing the highest possible resolution. This resolution will be used to detect and understand transients, to determine the three-dimensional velocity field (particularly vertical motion), and to improve measurement precision by understanding the complex noise sources inherent in GPS. The PBO Nucleus Project is designed operate, maintain and upgrade a subset of six western U.S. geodetic networks: the Alaska Deformation Array (AKDA), Bay Area Regional Deformation network (BARD), the Basin and Range Geodetic Network (BARGEN), the Eastern Basin and Range/Yellowstone network (EBRY), the Pacific Northwest Geodetic Array (PANGA), and the Southern California Integrated Geodetic Network (SCIGN), until they are subsumed by PBO in 2008. Uninterrupted data flow from these stations will effectively double the time-series length of PBO over the expected life of EarthScope, and create, for the first time, a single GPS-based geodetic network in the US. Other existing sites will remain in operation under support from non-NSF sources (e.g. the USGS), and EarthScope will benefit from their continued operation. On the grounds of relevance to EarthScope science goals, geographic distribution and data quality, 209 of the 432 existing stations have been selected as the nucleus upon which to build PBO. We have begun converting these stations to a PBO-compatible mode of operation; data now flow directly to PBO archives and processing centers while maintenance, operations, and meta-data requirements are currently under upgrade to PBO standards.

Datum maintenance of the main Egyptian geodetic control networks by utilizing Precise Point Positioning "PPP" technique

NASA Astrophysics Data System (ADS)

Rabah, Mostafa; Elmewafey, Mahmoud; Farahan, Magda H.

2016-06-01

A geodetic control network is the wire-frame or the skeleton on which continuous and consistent mapping, Geographic Information Systems (GIS), and surveys are based. Traditionally, geodetic control points are established as permanent physical monuments placed in the ground and precisely marked, located, and documented. With the development of satellite surveying methods and their availability and high degree of accuracy, a geodetic control network could be established by using GNSS and referred to an international terrestrial reference frame used as a three-dimensional geocentric reference system for a country. Based on this concept, in 1992, the Egypt Survey Authority (ESA) established two networks, namely High Accuracy Reference Network (HARN) and the National Agricultural Cadastral Network (NACN). To transfer the International Terrestrial Reference Frame to the HARN, the HARN was connected with four IGS stations. The processing results were 1:10,000,000 (Order A) for HARN and 1:1,000,000 (Order B) for NACN relative network accuracy standard between stations defined in ITRF1994 Epoch1996. Since 1996, ESA did not perform any updating or maintaining works for these networks. To see how non-performing maintenance degrading the values of the HARN and NACN, the available HARN and NACN stations in the Nile Delta were observed. The Processing of the tested part was done by CSRS-PPP Service based on utilizing Precise Point Positioning "PPP" and Trimble Business Center "TBC". The study shows the feasibility of Precise Point Positioning in updating the absolute positioning of the HARN network and its role in updating the reference frame (ITRF). The study also confirmed the necessity of the absent role of datum maintenance of Egypt networks.

A proposed concept for a crustal dynamics information management network

NASA Technical Reports Server (NTRS)

Lohman, G. M.; Renfrow, J. T.

1980-01-01

The findings of a requirements and feasibility analysis of the present and potential producers, users, and repositories of space-derived geodetic information are summarized. A proposed concept is presented for a crustal dynamics information management network that would apply state of the art concepts of information management technology to meet the expanding needs of the producers, users, and archivists of this geodetic information.

Development and Implementation of Joint Programs in Laser Ranging and Other Space Geodetic Techniques

NASA Technical Reports Server (NTRS)

Pearlman, Michael R.; Carter, David (Technical Monitor)

2002-01-01

On-going activities of the NASA special consultant to WEGENER (Working group of European Geoscientists for the Establishment of Networks for Earth-science Research) program are reported. Topics cover include: the WEGENER 2002 conference in Greece and the International Laser Ranging Service (ILRS).

The current state of the creation and modernization of national geodetic and cartographic resources in Poland

NASA Astrophysics Data System (ADS)

Doskocz, Adam

2016-01-01

All official data are currently integrated and harmonized in a spatial reference system. This paper outlines a national geodetic and cartographic resources in Poland. The national geodetic and cartographic resources are an important part of the spatial information infrastructure in the European Community. They also provide reference data for other resources of Spatial Data Infrastructure (SDI), including: main and detailed geodetic control networks, base maps, land and buildings registries, geodetic registries of utilities and topographic maps. This paper presents methods of producing digital map data and technical standards for field surveys, and in addition paper also presents some aspects of building Global and Regional SDI.

Kinematics and Seismotectonics of the Montello Thrust Fault (Southeastern Alps, Italy) Revealed by Local GPS and Seismic Networks

NASA Astrophysics Data System (ADS)

Serpelloni, E.; Anderlini, L.; Cavaliere, A.; Danesi, S.; Pondrelli, S.; Salimbeni, S.; Danecek, P.; Massa, M.; Lovati, S.

2014-12-01

The southern Alps fold-and-thrust belt (FTB) in northern Italy is a tectonically active area accommodating large part of the ~N-S Adria-Eurasia plate convergence, that in the southeastern Alps ranges from 1.5 to 2.5 mm/yr, as constrained by a geodetically defined rotation pole. Because of the high seismic hazard of northeastern Italy, the area is well monitored at a regional scale by seismic and GPS networks. However, more localized seismotectonic and kinematic features, at the scale of the fault segments, are not yet resolved, limiting our knowledge about the seismic potential of the different fault segments belonging to the southeastern Alps FTB. Here we present the results obtained from the analysis of data collected during local seismic and geodetic experiments conducted installing denser geophysical networks across the Montello-Bassano-Belluno system, a segment of the FTB that is presently characterized by a lower sismicity rate with respect to the surrounding domains. The Montello anticline, which is the southernmost tectonic features of the southeastern Alps FTB (located ~15 km south of the mountain front), is a nice example of growing anticline associated with a blind thrust fault. However, how the Adria-Alps convergence is partitioned across the FTB and the seismic potential of the Montello thrust (the area has been struck by a Mw~6.5 in 1695 but the causative fault is still largely debated) remained still unresolved. The new, denser, GPS data show that this area is undergoing among the highest geodetic deformation rates of the entire south Alpine chain, with a steep velocity gradient across the Montello anticline. The earthquakes recorded during the experiment, precisely relocated with double difference methods, and the new earthquake focal mechanisms well correlate with available information about sub-surface geological structures and highlight the seismotectonic activity of the Montello thrust fault. We model the GPS velocities using elastic dislocations embedded in a kinematic block model approach, which suggest that the Montello thrust fault is weakly coupled with respect to surrounding segments of the southernmost thrust system. Future works will include the integration of InSAR data and the densification/improvement of the geodetic infrastructure.

Multi-disciplinary contributions of HartRAO to global geodesy and geodynamics

NASA Astrophysics Data System (ADS)

Combrinck, Ludwig

2015-04-01

The Hartebeesthoek Radio Astronomy Observatory (South Africa) supports global initiatives in both geodesy and geodynamics through an active programme of science platform provision in Africa, the Atlantic Ocean, Indian Ocean and Antarctica. Our involvement ranges from the installation of tide gauges, Global Navigation Satellite Systems stations, seismometers and accelerometers on remote islands to the installation of radar reflectors in Antarctica which enable accurate, geo-referenced maps of the Antarctic coast line to be made. Currently we also participate in the African VLBI Network (AVN), with the aim to densify not only astronomical observatories in Africa, but to improve the geometry and distribution of advanced geodetic and geophysical equipment to facilitate development of research platforms in Africa, which can be used for geodynamics and related sciences, supporting international projects such as the WEGENER initiative. We present our multi-disciplinary activities during the last decade and sketch the way forward. Participation of Africa in the global arena of astronomy, geodesy, geodynamics and related fields will receive a major boost during the next decade. This is partially due to the development of a component of the Square Kilometre Array (SKA) in Africa but also due to the Global Geodetic Observing System (GGOS) project and the international objectives of higher geodetic accuracies and more stable reference frames. Consequent spinoffs into many disciplines relying on global reference frames and sub-cm positional accuracies stand to benefit and Africa can play a major role in improving both science and network geometries.

Western Pyrenees geodetic deformation study using the Guipuzcoa GNSS network

NASA Astrophysics Data System (ADS)

Martín, Adriana; Sevilla, Miguel; Zurutuza, Joaquín

2018-07-01

The Basque Country in the north of Spain is located inside the Basque-Cantabrian basin of the western Pyrenees which remarkable seismic-tectonic implications justify the need of geodetic control in the area. In order to perform a crustal deformation study we have analysed all daily observations from the GNSS permanent network of Guipuzcoa and external IGS stations, from January 2007 to November 2011. We have carried out the data processing applying double differences methodology in the automatic processing module BPE (Bernese Processing Engine) from Bernese GNSS software version 5.0. Solution was aligned to geodetic reference framework ITRF2008, by using the IGS08 solution and updated satellite and terrestrial antennas calibration. This five years network study results: Coordinate time series, velocities and baseline lengths variations show internal stability among inner stations and from them with respect to outer IGS stations, concluding that no deformations have been observed.

Deformation monitoring at Nevado del Ruiz, Colombia - October 1985 - March 1988

USGS Publications Warehouse

Banks, N.G.; Carvajal, C.; Mora, H.; Tryggvason, E.

1990-01-01

Deformation studies began at Nevado del Ruiz 23 days before the devastating 13 November 1985 eruption, at least 12 months after precursory seismicity and fumarolic activity began. The late start in geodetic monitoring, limited number of stations in the pre-eruption network, and inconsistent patterns in the observed deformation limit conclusions about intrusive activity in the months and weeks prior to the eruption. However, the data require that the magma source of the devastating eruption was either deeper than 7 km or, if shallow, recovered the same volume and position within one week of the eruption. Geodetic monitoring resumed 1 week after the eruption and, by April 1986, included 11 tilt-leveling stations, 38 EDM lines, and 7 short leveling lines - a network capable of detecting emplacement or movement of magma volumes as small as 3 MCM (3 ?? 106 m3) to a depth of 2-3 km (using a point-source model), 10 MCM to 7 km, 50 MCM to 10 km, and 200 MCM to 15 km beneath Ruiz. In addition, 4 telemetered tiltmeters provided the capability of detecting, in real time, the fairly rapid ascent of much smaller magma bodies. Stations established to detect instability of the summit ice cap after the eruption were discontinued in early 1986. The data collected from the geodetic networks have higher than normal variance but demonstrate that little or no cumulative deformation of Ruiz occurred from October 1985 through March 1988. Thus, little, if any, magma intruded above 5 km beneath the summit during or after the 13 November 1985 eruption. This lack of significant intrusive activity agrees with the surprisingly low seismic energy release under Ruiz and makes direct degassing of a large batholith an improbable explanation of the large sulfur flux to date at Ruiz. Part of the variance in the geodetic data results from real but noncumulative deformation that may in part be pressure-buffered by a fairly large geothermal water-gas mixture for which abundant physical evidence exists. Part of the noncumulative deformation, some of the fairly dispersed and low-level seismicity under Ruiz, and some phreatic events appear to correlate with seasonal precipitation patterns. Hence rain/snow-loading and groundwater interaction may cause deformation events and possibly help trigger some phreatic explosions and seismic events at Ruiz and, as search of the literature reveals, at other volcanoes in metastable states. ?? 1990.

RTX Correction Accuracy and Real-Time Data Processing of the New Integrated SeismoGeodetic System with Real-Time Acceleration and Displacement Measurements for Earthquake Characterization Based on High-Rate Seismic and GPS Data

NASA Astrophysics Data System (ADS)

Zimakov, L. G.; Raczka, J.; Barrientos, S. E.

2016-12-01

We will discuss and show the results obtained from an integrated SeismoGeodetic System, model SG160-09, installed in the Chile (Chilean National Network), Italy (University of Naples Network), and California. The SG160-09 provides the user high rate GNSS and accelerometer data, full epoch-by-epoch measurement integrity and the ability to create combined GNSS and accelerometer high-rate (200Hz) displacement time series in real-time. The SG160-09 combines seismic recording with GNSS geodetic measurement in a single compact, ruggedized case. The system includes a low-power, 220-channel GNSS receiver powered by the latest Trimble-precise Maxwell™6 technology and supports tracking GPS, GLONASS and Galileo signals. The receiver incorporates on-board GNSS point positioning using Real-Time Precise Point Positioning (PPP) technology with satellite clock and orbit corrections delivered over IP networks. The seismic recording includes an ANSS Class A, force balance accelerometer with the latest, low power, 24-bit A/D converter, producing high-resolution seismic data. The SG160-09 processor acquires and packetizes both seismic and geodetic data and transmits it to the central station using an advanced, error-correction protocol providing data integrity between the field and the processing center. The SG160-09 has been installed in three seismic stations in different geographic locations with different Trimble global reference stations coverage The hardware includes the SG160-09 system, external Zephyr Geodetic-2 GNSS antenna, both radio and high-speed Internet communication media. Both acceleration and displacement data was transmitted in real-time to the centralized Data Acquisition Centers for real-time data processing. Command/Control of the field station and real-time GNSS position correction are provided via the Pivot platform. Data from the SG160-09 system was used for seismic event characterization along with data from traditional seismic and geodetic stations installed in the network. Our presentation will focus on the key improvements of the network installation with the SG160-09 system, RTX correction accuracy obtained from Trimble Global RTX tracking network, rapid data transmission, and real-time data processing for strong seismic events and aftershock characterization.

On Similarity Transformation and Geodetic Network Distortions Based on Doppler Satellite Observations

NASA Technical Reports Server (NTRS)

Leick, Alfred; Vangelder, Boudewijn H. W.

1975-01-01

Models used in geodesy to transform two sets of coordinates are studied and distortions in geodetic networks are investigated. Commonly used transformation models are first reviewed and most of them are interpreted. Differences between various models are discussed. Pitfalls in partial solutions are then considered. It is shown that only as many chords and/or directional elements can be used in the computation as are needed to completely determine the size or shape of the polyhedron implied in the set of Cartesian coordinates. Each additional element causes the normal matrix to be singular provided that all correlations between the chords are used. A number of tables and maps indicating distortions in the NAD 27, Precise Traverse M-R '72, AUS, and SAD 69 geodetic datums are also included. The residuals of the coordinates are scanned for systematic patterns after transforming each geodetic system to the NWL9D Doppler system. Also, an attempt is made to show scale distortions in the NAD 27.

Monitoring of stability of ASG-EUPOS network coordinates

NASA Astrophysics Data System (ADS)

Figurski, M.; Szafranek, K.; Wrona, M.

2009-04-01

ASG-EUPOS (Active Geodetic Network - European Position Determination System) is the national system of precise satellite positioning in Poland, which increases a density of regional and global GNSS networks and is widely used by public administration, national institutions, entrepreneurs and citizens (especially surveyors). In near future ASG-EUPOS is to take role of main national network. Control of proper activity of stations and realization of ETRS'89 is a necessity. User of the system needs to be sure that observations quality and coordinates accuracy are high enough. Coordinates of IGS (International GNSS Service) and EPN (European Permanent Network) stations are precisely determined and any changes are monitored all the time. Observations are verified before they are archived in regional and global databases. The same applies to ASG-EUPOS. This paper concerns standardization of GNSS observations from different stations (uniform adjustment), examination of solutions correctness according to IGS and EPN standards and stability of solutions and sites activity

Activities at Sejong Station

NASA Astrophysics Data System (ADS)

Yi, Sang-oh; Sung, Yun-mo; Ah, Ki-duk; Oh, Hong-jong; Byon, Do-young; Lim, Hyung-chul; Chung, Moon-hee; Je, Do-heung; Jung, Tae-hyun

2016-12-01

The Sejong station is a part of the SGOC (Space Geodetic Observation Center) which belongs to the NGII (National Geographic Information Institute). This report will briefly describe the Sejong S/X system issues that we need to improve, establishment of a server cluster for S/W correlation, and installation of the ARGO-M (mobile SLR system, 40 cm in diameter) which is developed by KASI (Korea Astronomy and Space Science Institute) at the Sejong station. Construction of the Korea VLBI Network KVNG (Korea VLBI Network for Geodesy) is currently underway.

Breadth of Scientific Activities and Network Station Specifications in the IGS

NASA Technical Reports Server (NTRS)

Moore, A. W.; Springer, T. A.; Reigber, Ch.

1999-01-01

This presentation provides a brief overview of the scientific activities of the International GPS Service (IGS). This was an approved activity of the International Association of Geodesy (IAG) with official start of service on 1 Jan 1994. The mission of the IGS is "To provide a service to support geodetic and geophysical research activities, through GPS data and data products." The presentation explains the concept of the IGS working group, and pilot projects, and reviews the current working groups and pilot projects.

Global Positioning System (GPS) survey of Augustine Volcano, Alaska, August 3-8, 2000: data processing, geodetic coordinates and comparison with prior geodetic surveys

USGS Publications Warehouse

Pauk, Benjamin A.; Power, John A.; Lisowski, Mike; Dzurisin, Daniel; Iwatsubo, Eugene Y.; Melbourne, Tim

2001-01-01

Between August 3 and 8,2000,the Alaska Volcano Observatory completed a Global Positioning System (GPS) survey at Augustine Volcano, Alaska. Augustine is a frequently active calcalkaline volcano located in the lower portion of Cook Inlet (fig. 1), with reported eruptions in 1812, 1882, 1909?, 1935, 1964, 1976, and 1986 (Miller et al., 1998). Geodetic measurements using electronic and optical surveying techniques (EDM and theodolite) were begun at Augustine Volcano in 1986. In 1988 and 1989, an island-wide trilateration network comprising 19 benchmarks was completed and measured in its entirety (Power and Iwatsubo, 1998). Partial GPS surveys of the Augustine Island geodetic network were completed in 1992 and 1995; however, neither of these surveys included all marks on the island.Additional GPS measurements of benchmarks A5 and A15 (fig. 2) were made during the summers of 1992, 1993, 1994, and 1996. The goals of the 2000 GPS survey were to:1) re-measure all existing benchmarks on Augustine Island using a homogeneous set of GPS equipment operated in a consistent manner, 2) add measurements at benchmarks on the western shore of Cook Inlet at distances of 15 to 25 km, 3) add measurements at an existing benchmark (BURR) on Augustine Island that was not previously surveyed, and 4) add additional marks in areas of the island thought to be actively deforming. The entire survey resulted in collection of GPS data at a total of 24 sites (fig. 1 and 2). In this report we describe the methods of GPS data collection and processing used at Augustine during the 2000 survey. We use this data to calculate coordinates and elevations for all 24 sites surveyed. Data from the 2000 survey is then compared toelectronic and optical measurements made in 1988 and 1989. This report also contains a general description of all marks surveyed in 2000 and photographs of all new marks established during the 2000 survey (Appendix A).

The Global Geodetic Observing System: Space Geodesy Networks for the Future

NASA Technical Reports Server (NTRS)

Pearlman, Michael; Pavlis, Erricos; Ma, Chopo; Altamini, Zuheir; Noll, Carey; Stowers, David

2011-01-01

Ground-based networks of co-located space geodetic techniques (VLBI, SLR, GNSS. and DORIS) are the basis for the development and maintenance of the International Terrestrial Reference frame (ITRF), which is our metric of reference for measurements of global change, The Global Geodetic Observing System (GGOS) of the International Association of Geodesy (IAG) has established a task to develop a strategy to design, integrate and maintain the fundamental geodetic network and supporting infrastructure in a sustainable way to satisfy the long-term requirements for the reference frame. The GGOS goal is an origin definition at 1 mm or better and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components. These goals are based on scientific requirements to address sea level rise with confidence, but other applications are not far behind. Recent studies including one by the US National Research Council has strongly stated the need and the urgency for the fundamental space geodesy network. Simulations are underway to examining accuracies for origin, scale and orientation of the resulting ITRF based on various network designs and system performance to determine the optimal global network to achieve this goal. To date these simulations indicate that 24 - 32 co-located stations are adequate to define the reference frame and a more dense GNSS and DORIS network will be required to distribute the reference frame to users anywhere on Earth. Stations in the new global network will require geologically stable sites with good weather, established infrastructure, and local support and personnel. GGOS wil seek groups that are interested in participation. GGOS intends to issues a Call for Participation of groups that would like to contribute in the network implementation and operation. Some examples of integrated stations currently in operation or under development will be presented. We will examine necessary conditions and challenges in designing a co-location station.

Permanent GPS Geodetic Array in Southern California (PGGA) and GPS observations in Indonesia

NASA Technical Reports Server (NTRS)

Bock, Yehuds

1994-01-01

The Permanent GPS Geodetic Array (PGGA) is a network of permanent monitoring GPS stations in southern California devoted to the continuous measurement of crustal deformation in near real-time. The PGGA plays a unique role in studies of the kinematics of crustal deformation and the earthquake cycle in southern California because it is also providing temporally dense geodetic measurements of crustal motion over periods of minutes to variations in regional crustal strain. As it expands and matures the PGGA will play an increasingly important role in the study of active tectonics of southern California by bridging the frequency range between seismology, observatory geodesy, paleoseismology, and geology. In Indonesia GPS data is used for measurement of a large scale crustal deformation, extending from north China to the Indonesian archipelago. Indonesia offers a tremendous laboratory to study some of the processes that build continents, and mountains are active there. We began GPS observations in August 1989 on mainland Sumatra and the Mentawai Islands to study the phenomena of oblique plate convergence. We have analyzed the Indonesian data in conjunction with data collected on Christmas and Cocos Islands and at Darwin, Australia, and with the triangulation data in Sumatra.

TIGO: a geodetic observatory for the improvement of the global reference frame

NASA Astrophysics Data System (ADS)

Schlueter, Wolfgang; Hase, Hayo; Boeer, Armin

1999-12-01

The Bundesamt fuer Kartographie und Geodaesie (BKG) will provide a major contribution to the improvement and maintenance of the global reference frames: ICRF (International Celestial Reference Frame), ITRF (International Terrestrial Reference Frame) with the operation of TIGO (Transportable Integrated Geodetic Observatory). TIGO is designed as a transportable geodetic observatory which consists of all relevant geodetic space techniques for a fundamental station (including VLBI, SLR, GPS). The transportability of the observatory enables to fill up gaps in the International Space Geodetic Network and to optimize the contribution to the global reference frames. TIGO should operate for a period of 2 to 3 years (at minimum) at one location. BKG is looking for a cooperation with countries willing to contribute to the ITRF and to support the operation of TIGO.

Measuring Crustal Deformation in the American West.

ERIC Educational Resources Information Center

Jordan, Thomas H.; Minster, J. Bernard

1988-01-01

Suggests that there is a close relationship between deformation in the western United States and the large-scale motions of tectonic plates. Introduces very-long-baseline interferometry (VLBI) as one of the space-geodetic techniques, vector addition of the VLBI data and geological data, and a new geodetic network. (YP)

Combining Real-time Seismic and Geodetic Data to Improve Rapid Earthquake Information

NASA Astrophysics Data System (ADS)

Murray, M. H.; Neuhauser, D. S.; Gee, L. S.; Dreger, D. S.; Basset, A.; Romanowicz, B.

2002-12-01

The Berkeley Seismological Laboratory operates seismic and geodetic stations in the San Francisco Bay area and northern California for earthquake and deformation monitoring. The seismic systems, part of the Berkeley Digital Seismic Network (BDSN), include strong motion and broadband sensors, and 24-bit dataloggers. The data from 20 GPS stations, part of the Bay Area Regional Deformation (BARD) network of more than 70 stations in northern California, are acquired in real-time. We have developed methods to acquire GPS data at 12 stations that are collocated with the seismic systems using the seismic dataloggers, which have large on-site data buffer and storage capabilities, merge it with the seismic data stream in MiniSeed format, and continuously stream both data types using reliable frame relay and/or radio modem telemetry. Currently, the seismic data are incorporated into the Rapid Earthquake Data Integration (REDI) project to provide notification of earthquake magnitude, location, moment tensor, and strong motion information for hazard mitigation and emergency response activities. The geodetic measurements can provide complementary constraints on earthquake faulting, including the location and extent of the rupture plane, unambiguous resolution of the nodal plane, and distribution of slip on the fault plane, which can be used, for example, to refine strong motion shake maps. We are developing methods to rapidly process the geodetic data to monitor transient deformation, such as coseismic station displacements, and for combining this information with the seismic observations to improve finite-fault characterization of large earthquakes. The GPS data are currently processed at hourly intervals with 2-cm precision in horizontal position, and we are beginning a pilot project in the Bay Area in collaboration with the California Spatial Reference Center to do epoch-by-epoch processing with greater precision.

The Contribution of the IGS to a Globally Integrated Geodetic Observing System

NASA Astrophysics Data System (ADS)

WEBER, R.

2002-05-01

The dedicated goal of the International GPS Service (IGS) is 'to provide a service to support geodetic and geophysical research activities through GPS data and data products'. To accomplish its mission IGS began routine operations in Jan 1994. Nowadays operations are based on a large number of components like a globally distributed tracking network of about 200 stations, local and regional data centers as well as eight analysis centers. This presentation summarizes the measurement principles of the GPS and GLONASS microwave satellite navigation systems. An overview of current IGS-products will be given and factors limiting the accuracy of these products are discussed. Moreover IGS serves as one of the technique center of the IERS and therefore the delivered products follow designated IERS standards as close as possible. It can be anticipated that the IGS will also play an important role within the framework of an upcoming Globally Integrated Geodetic Observing System. Even today there are a number of scientific crosslinks to other space geodetic techniques and services e.g. to the ILRS in the determination of the geocentre or to the IVS in questions of a temporal and spatial densification of the reference frame. The above-mentioned initiative will strengthen further the cooperation and increase the scientific outcome.

Plate motions and deformations from geologic and geodetic data

NASA Technical Reports Server (NTRS)

Jordan, Thomas H.

1989-01-01

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI derived rates of deformation requires an examination of geologic information and more densely sampled ground based geodetic data. Triangulation and trilateration data measured on two regional networks, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault, were processed. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data were utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geologic structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. VLBI data was also processed from stations distributed across the Pacific-North America plate boundary zone in the western U.S. The VLBI data were used to constrain the integrated rate of deformation across portions of the continental plate boundary in California and to provide a tectonic framework to interpret regional geodetic and geologic studies.

Geodetic monitoring of subrosion-induced subsidence processes in urban areas

NASA Astrophysics Data System (ADS)

Kersten, Tobias; Kobe, Martin; Gabriel, Gerald; Timmen, Ludger; Schön, Steffen; Vogel, Detlef

2017-03-01

The research project SIMULTAN applies an advanced combination of geophysical, geodetic, and modelling techniques to gain a better understanding of the evolution and characteristics of sinkholes. Sinkholes are inherently related to surface deformation and, thus, of increasing societal relevance, especially in dense populated urban areas. One work package of SIMULTAN investigates an integrated approach to monitor sinkhole-related mass translations and surface deformations induced by salt dissolution. Datasets from identical and adjacent points are used for a consistent combination of geodetic and geophysical techniques. Monitoring networks are established in Hamburg and Bad Frankenhausen (Thuringia). Levelling surveys indicate subsidence rates of about 4-5 mm per year in the main subsidence areas of Bad Frankenhausen with a local maximum of 10 mm per year around the leaning church tower. Here, the concept of combining geodetic and gravimetric techniques to monitor and characterise geological processes on and below the Earth's surface is exemplary discussed for the focus area Bad Frankenhausen. For the different methods (levelling, GNSS, relative/absolute gravimetry) stable network results at identical points are obtained by the first campaigns, i.e., the results are generally in agreement.

3-D kinematics analysis of surface ruptures on an active creeping fault at Chihshang, Eastern Taiwan

NASA Astrophysics Data System (ADS)

Lee, J.; Angelier, J.; Chen, H.; Chu, H.; Hu, J.

2003-12-01

The Chihshang fault is one of the most active segments of the Longitudinal Valley Fault, the plate suture between the converging Philippine and Eurasian plates. A destructive earthquake of M 7.1 with substantial surface scarps resulted from rupturing of the Chihshang fault in 1951. From that on, no big earthquake greater than M 5.5 occurred in this area. Instead, the Chihshang fault reveals a creeping behavior at a rapid rate of about 20 mm/yr at least during the past 20 years. The surface breaks of the creeping Chihshang fault can be observed at the several places. A typical feature is reverse-fault-like fractures on the retaining wall. We deployed small geodetic networks across the fault zone at five sites. Each network comprises of 5 to 15 benchmarks. Trilateration measurements including angles and distances as well as leveling among the benchmarks have been carried out on an annual basis or twice a year since 1998. Compared to previous other measurements which have shown the first order creep rate for the entire fault zone, the present geodetic data provides the detailed information of the surface movements across the fault zone which usually composed of more than one fault strands and folds structures. According to our data from the local geodetic networks, we are able to reconstruct the 3-D kinematics of surface deformation across the Chihshang fault zone. Multiple fault strands are common along the Chihshang fault. Oblique shortening occurred at all sites and was characterized by a combination of thrusts, backthrust and surface warps. Strike-slip motion can also be distinguished on some fault strands. It is worth to note that the cultural feature, such as concrete basement of strong resistance, sometimes acted as deflection of surface ruptures. It should be taken into consideration for mitigation against seismic hazards.

GGOS working group on ground networks and communications

NASA Technical Reports Server (NTRS)

Pearlman, M.; Altamimi, Z.; Beck, N.; Forsberg, R.; Gurtner, W.; Kenyon, S.; Behrend, D.; Lemoine, F. G.; Ma, C.; Noll, C. E.;

The combined geodetic network adjusted on the reference ellipsoid - a comparison of three functional models for GNSS observations

NASA Astrophysics Data System (ADS)

Kadaj, Roman

2016-12-01

The adjustment problem of the so-called combined (hybrid, integrated) network created with GNSS vectors and terrestrial observations has been the subject of many theoretical and applied works. The network adjustment in various mathematical spaces was considered: in the Cartesian geocentric system on a reference ellipsoid and on a mapping plane. For practical reasons, it often takes a geodetic coordinate system associated with the reference ellipsoid. In this case, the Cartesian GNSS vectors are converted, for example, into geodesic parameters (azimuth and length) on the ellipsoid, but the simple form of converted pseudo-observations are the direct differences of the geodetic coordinates. Unfortunately, such an approach may be essentially distorted by a systematic error resulting from the position error of the GNSS vector, before its projection on the ellipsoid surface. In this paper, an analysis of the impact of this error on the determined measures of geometric ellipsoid elements, including the differences of geodetic coordinates or geodesic parameters is presented. Assuming that the adjustment of a combined network on the ellipsoid shows that the optimal functional approach in relation to the satellite observation, is to create the observational equations directly for the original GNSS Cartesian vector components, writing them directly as a function of the geodetic coordinates (in numerical applications, we use the linearized forms of observational equations with explicitly specified coefficients). While retaining the original character of the Cartesian vector, one avoids any systematic errors that may occur in the conversion of the original GNSS vectors to ellipsoid elements, for example the vector of the geodesic parameters. The problem is theoretically developed and numerically tested. An example of the adjustment of a subnet loaded from the database of reference stations of the ASG-EUPOS system was considered for the preferred functional model of the GNSS observations.

A Community-based Partnership for a Sustainable GNSS Geodetic Network

NASA Astrophysics Data System (ADS)

Dokka, R. K.

2009-12-01

Geodetic networks offer unparalleled opportunities to monitor and understand many of the rhythms of the Earth most vital to the sustainability of modern and future societies, i.e., crustal motions, sea-level, and the weather. For crustal deformation studies, the advantage is clear. Modern measurements allow us to document not only the permanent strains incurred over a seismic cycle, for example, but also the ephemeral strains that are critical for understanding the underlying physical mechanism. To be effective for science, however, geodetic networks must be properly designed, capitalized, and maintained over sufficient time intervals to fully capture the processes in action. Unfortunately, most networks lack interoperability and lack a business plan to ensure long term sustainability. The USA, for example, lacks a unified nation-wide GNSS network that can sustain its self over the coming years, decades, and century. Current federal priorities do not yet envision such a singular network. Publicly and privately funded regional networks exist, but tend to be parochial in scope, and optimized for a special user community, e.g., surveying, crustal motions, etc. Data sharing is common, but the lack of input at the beginning limits the functionality of the system for non-primary users. Funding for private networks depend heavily on the user demand, business cycle, and regulatory requirements. Agencies funding science networks offer no guarantee of sustained support. An alternative model (GULFNet) developed in Louisiana is meeting user needs, is sustainable, and is helping engineers, surveyors, and geologists become more spatially enabled. The common denominator among all participants is the view that accurate, precise, and timely geodetic data have tangible value for all segments of society. Although operated by a university (LSU), GULFNet is a community-based partnership between public and private sectors. GULFNet simultaneously achieves scientific goals by providing data to multiple user communities, supports National Spatial Reference System needs through NGS CORS, and serves the private sector by helping to make it become more profitable. The private sector participates through direct support that sustains operations, but most importantly by raising awareness among policy makers and federal and state appropriators.

The Most Remote Point Method for the Site Selection of the Future VGOS Network

NASA Astrophysics Data System (ADS)

Hase, Hayo; Pedreros, Felipe

2014-12-01

The VLBI Global Observing System (VGOS) will be part of the Global Geodetic Observing System (GGOS) and will consist of globally well distributed geodetic observatories. The most remote point (MRP) method is used to identify gaps in the network geometry. In each iteration step the identified most remote points are assumed to become new observatory sites improving the homogeneity of the global network. New locations for VGOS observatories have been found in La Plata, Tahiti, O'Higgins, Galapagos, Colombo, and Syowa. This contribution is an excerpt of a work published in Journal of Geodesy (DOI: 10.1007/s00190-014-0731-y) covering the site selection for the GGOS.%

Field Installation and Real-Time Data Processing of the New Integrated SeismoGeodetic System with Real-Time Acceleration and Displacement Measurements for Earthquake Characterization Based on High-Rate Seismic and GPS Data

NASA Astrophysics Data System (ADS)

Zimakov, Leonid; Jackson, Michael; Passmore, Paul; Raczka, Jared; Alvarez, Marcos; Barrientos, Sergio

2015-04-01

We will discuss and show the results obtained from an integrated SeismoGeodetic System, model SG160-09, installed in the Chilean National Network. The SG160-09 provides the user high rate GNSS and accelerometer data, full epoch-by-epoch measurement integrity and, using the Trimble Pivot™ SeismoGeodetic App, the ability to create combined GNSS and accelerometer high-rate (200Hz) displacement time series in real-time. The SG160-09 combines seismic recording with GNSS geodetic measurement in a single compact, ruggedized package. The system includes a low-power, 220-channel GNSS receiver powered by the latest Trimble-precise Maxwell™6 technology and supports tracking GPS, GLONASS and Galileo signals. The receiver incorporates on-board GNSS point positioning using Real-Time Precise Point Positioning (PPP) technology with satellite clock and orbit corrections delivered over IP networks. The seismic recording element includes an ANSS Class A, force balance triaxial accelerometer with the latest, low power, 24-bit A/D converter, which produces high-resolution seismic data. The SG160-09 processor acquires and packetizes both seismic and geodetic data and transmits it to the central station using an advanced, error-correction protocol with back fill capability providing data integrity between the field and the processing center. The SG160-09 has been installed in the seismic station close to the area of the Iquique earthquake of April 1, 2014, in northern Chile, a seismically prone area at the current time. The hardware includes the SG160-09 system, external Zephyr Geodetic-2 GNSS antenna, and high-speed Internet communication media. Both acceleration and displacement data was transmitted in real-time to the National Seismological Center in Santiago for real-time data processing using Earthworm / Early Bird software. Command/Control of the field station and real-time GNSS position correction are provided via the Pivot software suite. Data from the SG160-09 system was used for seismic event characterization along with data from traditional stand-alone broadband seismic and geodetic stations installed in the network. Our presentation will focus on the key improvements of the network installation with the SG160-09 system, rapid data transmission, and real-time data processing for strong seismic events and aftershock characterization as well as advanced features of the SG160-09 for Earthquake and Tsunami Early Warning system.

Active Transtensional Tectonics Due to Differentially Rotating Upper Crustal Blocks East of the Eastern Himalayan syntaxis, Yunnan Province, China.

NASA Astrophysics Data System (ADS)

Studnikigizbert, C.; Eich, L.; King, R.; Burchfiel, B. C.; Chen, Z.; Chen, L.

2004-12-01

Seismological (Holt et. al. 1996), geodetic (King et. al. 1996, Chen et. al. 2000) and geological (Wang et. al. 1995, Wang and Burchfiel 2002) studies have shown that upper crustal material north and east of the eastern Himalayan syntaxis rotates clockwise about the syntaxis, with the Xianshuihe fault accommodating most of this motion. Within the zone of rotating material, however, deformation is not completely homogenous, and numerous differentially rotating small crustal fragments are recognised. We combine seismic (CSB and Harvard CMT catalogues), geodetic (CSB and MIT-Chengdu networks), remote sensing, compilation of existing regional maps and our own detailed field mapping to characterise the active tectonics of a clockwise rotating crustal block between Zhongdian and Dali. The northeastern boundary is well-defined by the northwest striking left-lateral Zhongdian and Daju faults. The eastern boundary, on the other hand, is made up of a 80 km wide zone characterised by north-south trending extensional basins linked by NNE trending left-lateral faults. Geological mapping suggests that strain is accommodated by three major transtensional fault systems: the Jianchuan-Lijiang, Heqing and Chenghai fault systems. Geodetic data indicates that this zone accommodates 10 +/- 1.4 mm/year of E-W extension, but strain may be (presently) preferentially partitioned along the easternmost (Chenghai) fault. Not all geodetic velocities are consistent with geological observations. In particular, rotation and concomitant transtension are somehow transferred across the Red River-Tongdian faults to Nan Tinghe fault with no apparent accommodating structures. Rotation and extension is surmised to be related to the northward propagation of the syntaxis.

Strain Analysis in Horizontal Geodetic Network of Dams for Control of Stability and Monitoring Deformation

NASA Astrophysics Data System (ADS)

Roohi, S.; Ardalan, A. A.; Khodakarami, M.

2009-04-01

Dams as one of the engineering structures play very important role in human life. Because, from primary human needs such as providing drinking water to professional needs such as water powerhouse creation in order to provide power for industrial centers, hospitals, manufactures and agriculture, have considerable dependent on dams. In addition destruction of a dam can be as dangerous as earthquake. Therefore maintenance, stability control and monitoring deformation of them is indispensable. In order to control stability of dams and their around lands and monitoring deformation a network is created by surveyor, geologist and dam experts on crest and body of dam or on land near the dam. Geodetic observations are done in this network by precise surveying instrument in deferent time then by using linear least square parametric adjustment method, adjusted coordinates with their variance- covariance matrix and error ellipses, redundancy numbers for observation, blunders and … are estimated in each epoch. Then displacement vectors are computed in each point of network, After that by use of Lagrangeian deformation idea and constitution of deformation equations movement, displacement model is determined and strain tensor is computed. we can induce deformation information from strain tensor in different ways such as strain ellipse then interpret deformation that happen in each point of network. Also we can compute rigid rotation from anti-symmetric part of displacement gradient tensor. After processing tow consequence epochs observations of horzontal geodetic network of Hnna dam in southwest of Esfahan, the most semi-major axis of error ellipse is estimated about 0.9mm for point D10, largest displacement is 1.4mm for point C3 that it's semimajor axis of displacement error ellipse is 1.3mm and there is different shear in all of network points exceptional points D2,C3 and C2. There is different dilatation in most of points. These amount of maximum shear and dilatation are justified because of horizontal displacement and subsidence of dam due to pressure of water that conserve behind it. Key word: strain tensor, monitoring deformation, Geodetic network, deformation equation movement, error ellipse, strain ellipse, shear, dilatation

LAGEOS geodetic analysis-SL7.1

NASA Technical Reports Server (NTRS)

Smith, D. E.; Kolenkiewicz, R.; Dunn, P. J.; Klosko, S. M.; Robbins, J. W.; Torrence, M. H.; Williamson, R. G.; Pavlis, E. C.; Douglas, N. B.; Fricke, S. K.

1991-01-01

Laser ranging measurements to the LAGEOS satellite from 1976 through 1989 are related via geodetic and orbital theories to a variety of geodetic and geodynamic parameters. The SL7.1 analyses are explained of this data set including the estimation process for geodetic parameters such as Earth's gravitational constant (GM), those describing the Earth's elasticity properties (Love numbers), and the temporally varying geodetic parameters such as Earth's orientation (polar motion and Delta UT1) and tracking site horizontal tectonic motions. Descriptions of the reference systems, tectonic models, and adopted geodetic constants are provided; these are the framework within which the SL7.1 solution takes place. Estimates of temporal variations in non-conservative force parameters are included in these SL7.1 analyses as well as parameters describing the orbital states at monthly epochs. This information is useful in further refining models used to describe close-Earth satellite behavior. Estimates of intersite motions and individual tracking site motions computed through the network adjustment scheme are given. Tabulations of tracking site eccentricities, data summaries, estimated monthly orbital and force model parameters, polar motion, Earth rotation, and tracking station coordinate results are also provided.

Assessment of the DORIS network monumentation

NASA Astrophysics Data System (ADS)

Saunier, J.

2016-12-01

Stability of the monumentation is essential for precise positioning applications to minimize velocity uncertainties and noises in the position data. In charge of the DORIS global tracking network deployment since the beginning, IGN, in consultation with CNES, designed three standard monuments compliant with the DORIS system requirements and general geodetic specifications, and suitable for various site configurations: building roofs, concrete pedestals or pillars. This paper describes the monument types in use in the DORIS network according to the current required specifications and provides a comparative assessment of the stability of the monuments over the network based on three methods: a theoretical study of the mechanical behavior of the metallic structures, a misclosure analysis taken during ground surveys and a qualitative approach taking into account different factors. This overview of the network monumentation gives new key numbers following the previous network assessment performed by Fagard (2006). Significant improvements have been made following the continuous efforts to renovate the network monumentation. These results are relevant for the Global Geodetic Observing System (GGOS) goals of measurement stability for the geodetic techniques. Today, two-thirds of the DORIS network monuments are compliant with the standards aiming at stability of 0.1 mm/y. This stability result has been measured for 16 of the 58 stations more than 10 y after its installation while monuments with more than 1 mm antenna tilts are over 10 y old when specifications were less stringent. The grading and scoring grid drawn up for each monument led to the mapping of the stability of the current DORIS network. Finally, we present a number of further actions to monitor the monument stability and provide new elements for the network monumentation assessment, exploring two different approaches: analysis of the time series and direct measurements using devices placed on each monument.

Development of AN Open-Source Automatic Deformation Monitoring System for Geodetical and Geotechnical Measurements

NASA Astrophysics Data System (ADS)

Engel, P.; Schweimler, B.

2016-04-01

The deformation monitoring of structures and buildings is an important task field of modern engineering surveying, ensuring the standing and reliability of supervised objects over a long period. Several commercial hardware and software solutions for the realization of such monitoring measurements are available on the market. In addition to them, a research team at the Neubrandenburg University of Applied Sciences (NUAS) is actively developing a software package for monitoring purposes in geodesy and geotechnics, which is distributed under an open source licence and free of charge. The task of managing an open source project is well-known in computer science, but it is fairly new in a geodetic context. This paper contributes to that issue by detailing applications, frameworks, and interfaces for the design and implementation of open hardware and software solutions for sensor control, sensor networks, and data management in automatic deformation monitoring. It will be discussed how the development effort of networked applications can be reduced by using free programming tools, cloud computing technologies, and rapid prototyping methods.

Geodetic measurement of deformation in California. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Sauber, Jeanne Marie

1988-01-01

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 as part of the NASA Crustal Dynamics Project provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI-derived rates of deformation requires an examination of geologic information and more densely sampled ground-based geodetic data. In the first two of three related studies embodying this thesis triangulation and trilateration data measured on two regional networks are processed, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data have been utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geological structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. In the third study, VLBI data from stations distributed across the Pacific - North American plate boundary zone in the western United States are processed. The VLBI data have been used to constrain the integrated rate of deformation across portions of the continental plate boundary in California and to provide a tectonic framework to interpret regional geodetic and geologic studies.

Single-frequency receivers as master permanent stations in GNSS networks: precision and accuracy of the positioning in mixed networks

NASA Astrophysics Data System (ADS)

Dabove, Paolo; Manzino, Ambrogio Maria

2015-04-01

The use of GPS/GNSS instruments is a common practice in the world at both a commercial and academic research level. Since last ten years, Continuous Operating Reference Stations (CORSs) networks were born in order to achieve the possibility to extend a precise positioning more than 15 km far from the master station. In this context, the Geomatics Research Group of DIATI at the Politecnico di Torino has carried out several experiments in order to evaluate the achievable precision obtainable with different GNSS receivers (geodetic and mass-market) and antennas if a CORSs network is considered. This work starts from the research above described, in particular focusing the attention on the usefulness of single frequency permanent stations in order to thicken the existing CORSs, especially for monitoring purposes. Two different types of CORSs network are available today in Italy: the first one is the so called "regional network" and the second one is the "national network", where the mean inter-station distances are about 25/30 and 50/70 km respectively. These distances are useful for many applications (e.g. mobile mapping) if geodetic instruments are considered but become less useful if mass-market instruments are used or if the inter-station distance between master and rover increases. In this context, some innovative GNSS networks were developed and tested, analyzing the performance of rover's positioning in terms of quality, accuracy and reliability both in real-time and post-processing approach. The use of single frequency GNSS receivers leads to have some limits, especially due to a limited baseline length, the possibility to obtain a correct fixing of the phase ambiguity for the network and to fix the phase ambiguity correctly also for the rover. These factors play a crucial role in order to reach a positioning with a good level of accuracy (as centimetric o better) in a short time and with an high reliability. The goal of this work is to investigate about the real effect and how is the contribute of L1 mass-market permanent stations to the CORSs Network both for geodetic and low-cost receivers; in particular is described how the use of the network products which are generated by the network (in real-time and post-processing) can improve the accuracy and precision of a rover 5, 10 and 15 km far from the nearest station. Some tests have been carried out considering different types of receivers (geodetic and mass market) and antennas (patch and geodetic). The tests have been conducted considering several positioning approaches (static, stop and go and real time) in order to make the analysis more complete. Good and interesting results were obtained: the followed approach will be useful for many types of applications (landslides monitoring, traffic control), especially where the inter-station distances of GNSS permanent station are greater than 30 km.

Α Deformation study in Central Greece using 20 years of GPS data

NASA Astrophysics Data System (ADS)

Marinou, Aggeliki; Papazissi, Kaliopi; Mitsakaki, Christiana; Paradissis, Demitris; Papanikolaou, Xanthos; Anastasiou, Demitris

2015-04-01

Central Greece is a region recognized for its intense tectonic activity with the main characterics being the extension in the North-South direction. This extension is revealed mainly in the form of large parallel grabens. Among these rifts is the Corinth Gulf, which is the most active tectonically, the basin between Parnassos and Kallidromo Mt, the Locris basin and the graben of North Evoikos Gulf, while in the south lays the Thebes basin and the South Evoikos Gulf. Since the late eighties the Laboratory of Higher Geodesy and the Dionysos Satellite Observatory of the National Technical University of Athens, in cooperation with several National and International Universities and Institutions have established, in various Greek areas, of high seismic activity, geodetic networks in order to monitor tectonic displacements. These geodetic networks were observed periodically using Satellite Geodesy techniques and in recent years almost entirely GPS. In this study all the available GPS data, referring to the broader area of Evia, Attiki and Viotia, for the years 1989 to 2008, are analyzed. The displacement field and its temporal changes for the area between the two major geological features, the Corinth Gulf and the Evoikos Gulf, are investigated. Αll the kinematic models that were used do not confirm that the area of study is deforming homogeneously, while an indication of a discontinuity has been detected.

Seafloor seismological/geodetic observations in the rupture area of the 2011 Tohoku-oki Earthquake

NASA Astrophysics Data System (ADS)

Hino, Ryota; Shinohara, Masanao; Ito, Yoshihiro

2016-04-01

A number of important aspects of the 2011 Tohoku-oki earthquake (Mw 9.0) were clarified by the seafloor seismological and geodetic observation above the rupture area of the earthquake. Besides the extraordinarily large coseismic displacements, various kinds of slow slip phenomena associated with intensive micro-seismicity on the plate boundary fault were identified by near field ocean bottom seismographs and seafloor geodetic observation networks. The Tohoku-oki earthquake was preceded by evident foreshock activity with a spatial expansion of this seismicity. The activity became significantly intense after the occurrence of the largest foreshock two days before the mainshock rupture. During the period, clear continuous seafloor deformation was identified caused by the aseismic slip following the largest foreshock. Another different type of aseismic slip event had occurred before this pre-imminent activity had started about a month before the largest foreshock happened. The observed increased seismicity associated with aseismic slip suggests that there must have been some chain reaction like interplay of seismic and interseismic slips before the large earthquake broke out. However, no evident deformation signals were observed indicating acceleration of fault slip immediately before the mainshock. Seafloor geodetic measurements reveals that the postseismic deformation around the rupture area of the Tohoku-oki earthquake shows complex spatial pattern and the complexity is mostly due to significant viscoelastic relaxation induced by the huge coseismic slip. The effects of viscoelastic deformation makes it difficult to identify the deformation associated with the after slip or regaining of interplate coupling and requires us to enhance the abilities of seafloor monitoring to detect the slip activities on the fault. We started an array of seismometer arrays observation including broad-band seismographs to detect and locate slow-slip events and low-frequency tremors. Another observation we started is direct-path acoustic ranging across the trench axis. Slip rate of the shallow fault can be measured by monitoring the change in distance between the benchmarks on the incoming and overrding plates.

Haystack Analysis Center

NASA Technical Reports Server (NTRS)

Niell, Arthur; Cappallo, Roger; Corey, Brian; Titus, Mike

2013-01-01

Analysis activities at Haystack Observatory are directed towards improving the accuracy of geodetic measurements, whether these are from VLBI, GNSS, SLR, or any other technique. Those analysis activities that are related to technology development are reported elsewhere in this volume. In this report, a preliminary analysis of the first geodetic sessions with the new broadband geodetic VLBI system is reported.

Need for denser geodetic network to get real constrain on the fault behavior along the Main Marmara Sea segments of the NAF, toward an optimized GPS network.

NASA Astrophysics Data System (ADS)

Klein, E.; Masson, F.; Duputel, Z.; Yavasoglu, H.; Agram, P. S.

2016-12-01

Over the last two decades, the densification of GPS networks and the development of new radar satellites offered an unprecedented opportunity to study crustal deformation due to faulting. Yet, submarine strike slip fault segments remain a major issue, especially when the landscape appears unfavorable to the use of SAR measurements. It is the case of the North Anatolian fault segments located in the Main Marmara Sea, that remain unbroken ever since the Mw7.4 earthquake of Izmit in 1999, which ended a eastward migrating seismic sequence of Mw > 7 earthquakes. Located directly offshore Istanbul, evaluation of seismic hazard appears capital. But a strong controversy remains over whether these segments are accumulating strain and are likely to experience a major earthquake, or are creeping, resulting both from the simplicity of current geodetic models and the scarcity of geodetic data. We indeed show that 2D infinite fault models cannot account for the complexity of the Marmara fault segments. But current geodetic data in the western region of Istanbul are also insufficient to invert for the coupling using a 3D geometry of the fault. Therefore, we implement a global optimization procedure aiming at identifying the most favorable distribution of GPS stations to explore the strain accumulation. We present here the results of this procedure that allows to determine both the optimal number and location of the new stations. We show that a denser terrestrial survey network can indeed locally improve the resolution on the shallower part of the fault, even more efficiently with permanent stations. But data closer from the fault, only possible by submarine measurements, remain necessary to properly constrain the fault behavior and its potential along strike coupling variations.

Evaluating Pseudorange Multipath at CGPS Stations Spanning Mexico

NASA Astrophysics Data System (ADS)

Vazquez, G.; Bennett, R. A.; Spinler, J. C.

2013-12-01

A research study was conducted in order to quantify and analyze the amount of pseudorange multipath at continuous Global Positioning System (CGPS) stations spanning Mexico. These CGPS stations are administered by a variety of organizations, including government agencies and public universities, and thus serve a wide range of positioning needs. Despite the diversity of the networks and their intended audiences, a core function of all of the networks is to provide a stable framework for high-precision positioning in support of diverse commercial and scientific applications. CGPS data from a large number of publicly available networks located in Mexico were studied. These include the RGNA (National Active Geodetic Network) administered by INEGI (National Institute of Statistics and Geography), the PBO network (Plate Boundary Observatory) funded by the National Science Foundation (NSF) and operated by UNAVCO (University NAVstar Consortium), the Southern California Integrated GPS Network (SCIGN), which is a collaboration effort of the United States Geological Survey (USGS), Scripps Institution of Oceanography and the Jet Propulsion Laboratory (JPL), the UNAM network, operated by the National Seismological System (SSN) and the Institute of Geophysics of the National Autonomous University of Mexico (UNAM), the Suominet Geodetic Network (SNG) and the CORS (Continuously Operating Reference Station) network, operated by the Federal Aviation Administration (FAA). A total of 54 CGPS stations were evaluated, where dual-frequency geodetic-grade receivers collected GPS data continuously during the period from 1994 to 2013. It is usually assumed that despite carefully selected locations, all CGPS stations are to some extent, affected by the presence of signal multipath. In addition, the geographic distribution of stations provides a nation-wide access to the International Terrestrial Reference Frame (ITRF). For real-time kinematic (RTK) and rapid static applications that depend on the pseudo-range observable, the accuracy with which a roaming user may locate their assets with respect to the ITRF may be limited by site-specific multipath. The issue is particularly critical for users depending on pseudorange measurements for 'real-time' (or 'near-real-time') kinematic GPS positioning, where ambiguity resolution is a critical step. Therefore, to identify the most and the least affected GPS stations we analyzed the averaged daily root mean square pseudorange multipath variations (MP1-RMS and MP2-RMS) for all feasible satellites tracked by the CGPS networks. We investigated the sources of multipath, including changes associated with hardware replacement (i.e., receiver and antenna type) and receiver firmware upgrades.

Exploring deformation scenarios in Timanfaya volcanic area (Lanzarote, Canary Islands) from GNSS and ground based geodetic observations

NASA Astrophysics Data System (ADS)

Riccardi, U.; Arnoso, J.; Benavent, M.; Vélez, E.; Tammaro, U.; Montesinos, F. G.

2018-05-01

We report on a detailed geodetic continuous monitoring in Timanfaya volcanic area (TVA), where the most intense geothermal anomalies of Lanzarote Island are located. We analyze about three years of GNSS data collected on a small network of five permanent stations, one of which at TVA, deployed on the island, and nearly 20 years of tiltmeter and strainmeter records acquired at Los Camelleros site settled in the facilities of the Geodynamics Laboratory of Lanzarote within TVA. This study is intended to contribute to understanding the active tectonics on Lanzarote Island and its origin, mainly in TVA. After characterizing and filtering out the seasonal periodicities related to "non-tectonic" sources from the geodetic records, a tentative ground deformation field is reconstructed through the analysis of both tilt, strain records and the time evolution of the baselines ranging the GNSS stations. The joint interpretation of the collected geodetic data show that the area of the strongest geothermal anomaly in TVA is currently undergoing a SE trending relative displacement at a rate of about 3 mm/year. This area even experiences a significant subsidence with a maximum rate of about 6 mm/year. Moreover, we examine the possible relation between the observed deformations and atmospheric effects by modelling the response functions of temperature and rain recorded in the laboratory. Finally, from the retrieval of the deformation patterns and the joint analysis of geodetic and environmental observations, we propose a qualitative model of the interplaying role between the hydrological systems and the geothermal anomalies. Namely, we explain the detected time correlation between rainfall and ground deformation because of the enhancement of the thermal transfer from the underground heat source driven by the infiltration of meteoric water.

Leveraging geodetic data to reduce losses from earthquakes

USGS Publications Warehouse

Murray, Jessica R.; Roeloffs, Evelyn A.; Brooks, Benjamin A.; Langbein, John O.; Leith, William S.; Minson, Sarah E.; Svarc, Jerry L.; Thatcher, Wayne R.

2018-04-23

Seismic hazard assessments that are based on a variety of data and the best available science, coupled with rapid synthesis of real-time information from continuous monitoring networks to guide post-earthquake response, form a solid foundation for effective earthquake loss reduction. With this in mind, the Earthquake Hazards Program (EHP) of the U.S. Geological Survey (USGS) Natural Hazards Mission Area (NHMA) engages in a variety of undertakings, both established and emergent, in order to provide high quality products that enable stakeholders to take action in advance of and in response to earthquakes. Examples include the National Seismic Hazard Model (NSHM), development of tools for improved situational awareness such as earthquake early warning (EEW) and operational earthquake forecasting (OEF), research about induced seismicity, and new efforts to advance comprehensive subduction zone science and monitoring. Geodetic observations provide unique and complementary information directly relevant to advancing many aspects of these efforts (fig. 1). EHP scientists have long leveraged geodetic data for a range of influential studies, and they continue to develop innovative observation and analysis methods that push the boundaries of the field of geodesy as applied to natural hazards research. Given the ongoing, rapid improvement in availability, variety, and precision of geodetic measurements, considering ways to fully utilize this observational resource for earthquake loss reduction is timely and essential. This report presents strategies, and the underlying scientific rationale, by which the EHP could achieve the following outcomes: The EHP is an authoritative source for the interpretation of geodetic data and its use for earthquake loss reduction throughout the United States and its territories.The USGS consistently provides timely, high quality geodetic data to stakeholders.Significant earthquakes are better characterized by incorporating geodetic data into USGS event response products and by expanded use of geodetic imaging data to assess fault rupture and source parameters.Uncertainties in the NSHM, and in regional earthquake models, are reduced by fully incorporating geodetic data into earthquake probability calculations.Geodetic networks and data are integrated into the operations and earthquake information products of the Advanced National Seismic System (ANSS).Earthquake early warnings are improved by more rapidly assessing ground displacement and the dynamic faulting process for the largest earthquakes using real-time geodetic data.Methodology for probabilistic earthquake forecasting is refined by including geodetic data when calculating evolving moment release during aftershock sequences and by better understanding the implications of transient deformation for earthquake likelihood.A geodesy program that encompasses a balanced mix of activities to sustain missioncritical capabilities, grows new competencies through the continuum of fundamental to applied research, and ensures sufficient resources for these endeavors provides a foundation by which the EHP can be a leader in the application of geodesy to earthquake science. With this in mind the following objectives provide a framework to guide EHP efforts:Fully utilize geodetic information to improve key products, such as the NSHM and EEW, and to address new ventures like the USGS Subduction Zone Science Plan.Expand the variety, accuracy, and timeliness of post-earthquake information products, such as PAGER (Prompt Assessment of Global Earthquakes for Response), through incorporation of geodetic observations.Determine if geodetic measurements of transient deformation can significantly improve estimates of earthquake probability.Maintain an observational strategy aligned with the target outcomes of this document that includes continuous monitoring, recording of ephemeral observations, focused data collection for use in research, and application-driven data processing and analysis systems.Collaborate on research, development, and operation of affordable, high-precision seafloor geodetic methods that improve earthquake forecasting and event response.Advance computational techniques and instrumentation to enable use of strategies like repeat-pass imagery and low-cost geodetic sensors for earthquake response, monitoring, and research.Engage stakeholders and collaborate with partner institutions to foster operational and research objectives and to safeguard the continued health of geodetic infrastructure upon which we mutually depend.Maintaining a vibrant internal research program provides the foundation by which the EHP can remain an effective and trusted source for earthquake science. Exploiting abundant new data sources, evaluating and assimilating the latest science, and pursuing novel avenues of investigation are means to fulfilling the EHP’s core responsibilities and realizing the important scientific advances envisioned by its scientists. Central to the success of such a research program is engaging personnel with a breadth of competencies and a willingness and ability to adapt these to the program’s evolving priorities, enabling current staff to expand their skills and responsibilities, and planning holistically to meet shared workforce needs. In parallel, collaboration with external partners to support scientific investigations that complement ongoing internal research enables the EHP to strengthen earthquake information products by incorporating alternative perspectives and approaches and to study topics and geographic regions that cannot be adequately covered internally.With commensurate support from technical staff who possess diverse skills, including engineering, information technology, and proficiency in quantitative analysis combined with basic geophysical knowledge, the EHP can achieve the geodetic outcomes identified in this document.

VOLOBSIS: An Infrastructure for Open Access to Seismic and GNSS Data from the Volcanological and Seismological French Observatories

NASA Astrophysics Data System (ADS)

Satriano, C.; Lemarchand, A.; Saurel, J. M. M.; Pardo, C.; Vincent, D.; de Chabalier, J. B.; Beauducel, F.; Shapiro, N.; Cyril, G.

2016-12-01

The three Volcanological and Seismological Observatories of the Institut de Physique du Globe de Paris (IPGP) are situated in the overseas French territories: Martinique and Guadeloupe observatories in the Lesser Antilles and La Réunion Island in the Indian Ocean. The main missions of IPGP observatories is to monitor French active volcanoes and seismic activity associated with regional tectonics and to foster scientific research on the Lesser Antilles arc and La Réunion hotspot. For that, the observatories operate, among others, permanent seismological and geodetic networks and process and analyze continuously acquired data.IPGP observatories have a long story of seismic and geodetic monitoring: the first seismograph in Martinique was installed in 1902; starting from the early '80 the three observatories begun deploying permanent networks of analog sensors. During the years 2010, seismic and geodetic monitoring at the three observatories saw a significant breakthrough with the advent of broadband seismic sensors, digital recording and continuous GNSS receivers.This wealth of data is constituted today by 81 seismological stations (broad-band and short period, networks GL, MQ, PF and WI) and 48 permanent GNSS stations. Data of both type is continuously recorded and acquired at the three observatories, as well as at the IPGP Data Center in Paris. Real-time streams for seismic data are available through a SeedLink server. Seismic and GNSS data are further validated and completed at IPGP, and distributed through the VOLOBSIS web portal (http://volobsis.ipgp.fr), which provides download links as well a web service interface.Seismic data is further available through IRIS, the European Integrated Data Archive (EIDA) and the French RESIF portal (http://seismology.resif.fr).Here we discuss the different steps of data recording, quality-control and distribution behind VOLOBSIS, which provides an open data infrastructure for advancing the understanding of volcanic and tectonic deformation processes across the Lesser Antilles Arc and at La Réunion hotspot. We further discuss the planned future updates, with an upcoming real-time catalog of seismicity and the open and real-time distribution of additional type of data, such as tiltmeter and extensometer data, as well as geochemistry and meteorology.

New Developments in Geodetic Data Management Systems for Fostering International Collaborations in the Geosciences

NASA Astrophysics Data System (ADS)

Meertens, Charles; Boler, Fran; Miller, M. Meghan

2015-04-01

UNAVCO community investigators are actively engaged in using space and terrestrial geodetic techniques to study earthquake processes, mantle properties, active magmatic systems, plate tectonics, plate boundary zone deformation, intraplate deformation, glacial isostatic adjustment, and hydrologic and atmospheric processes. The first GPS field projects were conducted over thirty years ago, and from the beginning these science investigations and the UNAVCO constituency as a whole have been international and collaborative in scope and participation. Collaborations were driven by the nature of the scientific problems being addressed, the capability of the technology to make precise measurements over global scales, and inherent technical necessity for sharing of GPS tracking data across national boundaries. The International GNSS Service (IGS) was formed twenty years ago as a voluntary federation to share GPS data from now hundreds of locations around the globe to facilitate realization of global reference frames, ties to regional surveys, precise orbits, and to establish and improve best practices in analysis and infrastructure. Recently, however, numbers of regional stations have grown to the tens of thousands, often with data that are difficult to access. UNAVCO has been working to help remove technical barriers by providing open source tools such as the Geodetic Seamless Archive Centers software to facilitate cross-project data sharing and discovery and by developing Dataworks software to manage network data. Data web services also provide the framework for UNAVCO contributions to multi-technique, inter-disciplinary, and integrative activities such as CoopEUS, GEO Supersites, EarthScope, and EarthCube. Within the geodetic community, metadata standards and data exchange formats have been developed and evolved collaboratively through the efforts of global organizations such as the IGS. A new generation of metadata and data exchange formats, as well as the software tools that utilize these formats and that support more efficient exchange of the highest quality data and metadata, are currently being developed and deployed through multiple international efforts.

Variation Scenarios in System Deployments for the GGOS2020 Space Geodesy Network

NASA Astrophysics Data System (ADS)

Pavlis, Erricos C.; Kuzmicz-Cieslak, Magdalena; MacMillan, Daniel S.

2017-04-01

Simulation studies have so far determined an approximate size and station density for the Space Geodetic Network that will meet the requirements recommended by the U.S. National Research Council report "Precise Geodetic Infrastructure: National Requirements for a Shared Resource" (2010). A network of about 30 globally distributed "core" observatories with state of the art equipment needs to be deployed over the next decade. Subsequently, GGOS—the Global Geodetic Observing System issued a "Call for Proposals for the expansion and update of the network, to which several countries committed to contribute. The renewal process will not happen instantly and for a long time, the network will comprise legacy and next generation equipment. We conducted a new batch of simulation studies using the proposed site locations and the proposed equipment at each site, to gauge the contribution of specific systems and locations to the global results. The majority of the examined sites are well-established future sites, some of which are even close to completion. Despite the good intentions of the contributing agencies/countries, in some cases we have identified regional gaps in coverage with either SLR or VLBI systems. We have characterized the effect of these gaps on the quality of the final TRF. We present the results of these simulation studies and rank the examined cases according to the likelihood that the designed network will successfully meet the GGOS goals of 1 mm accuracy (decadal scale) and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components of the TRF.

GGOS2020 Space Geodesy Network: Variations in System Deployment Scenarios

NASA Astrophysics Data System (ADS)

Pavlis, E. C.; Koenig, D.; Kuzmicz-Cieslak, M.; MacMillan, D. S.

2016-12-01

Simulation studies have so far determined an approximate size and station density for the Space Geodetic Network that will meet the requirements recommended by the U.S. National Research Council report "Precise Geodetic Infrastructure: National Requirements for a Shared Resource" (2010). A network of about 30 globally distributed "core" observatories with state of the art equipment needs to be deployed over the next decade. Subsequently, GGOS—the Global Geodetic Observing System issued a "Call for Proposals for the expansion and update of the network, to which several countries committed to contribute. The renewal process will not happen instantly and for a long time, the network will comprise legacy and next generation equipment. We conducted a new batch of simulation studies using the proposed site locations and the proposed equipment at each site, to gauge the contribution of specific systems and locations to the global results. The majority of the examined sites are well-established future sites, some of which are even close to completion. Despite the good intentions of the contributing agencies/countries, in some cases we have identified regional gaps in coverage with either SLR or VLBI systems. We have characterized the effect of these gaps on the quality of the final TRF. We present the results of these simulation studies and rank the examined cases according to the likelihood that the designed network will successfully meet the GGOS goals of 1 mm accuracy (decadal scale) and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components of the TRF.

Direct determination of geocenter motion by combining SLR, VLBI, GNSS, and DORIS time series

NASA Astrophysics Data System (ADS)

Wu, X.; Abbondanza, C.; Altamimi, Z.; Chin, T. M.; Collilieux, X.; Gross, R. S.; Heflin, M. B.; Jiang, Y.; Parker, J. W.

2013-12-01

The longest-wavelength surface mass transport includes three degree-one spherical harmonic components involving hemispherical mass exchanges. The mass load causes geocenter motion between the center-of-mass of the total Earth system (CM) and the center-of-figure of the solid Earth surface (CF), and deforms the solid Earth. Estimation of the degree-1 surface mass changes through CM-CF and degree-1 deformation signatures from space geodetic techniques can thus complement GRACE's time-variable gravity data to form a complete change spectrum up to a high resolution. Currently, SLR is considered the most accurate technique for direct geocenter motion determination. By tracking satellite motion from ground stations, SLR determines the motion between CM and the geometric center of its ground network (CN). This motion is then used to approximate CM-CF and subsequently for deriving degree-1 mass changes. However, the SLR network is very sparse and uneven in global distribution. The average number of operational tracking stations is about 20 in recent years. The poor network geometry can have a large CN-CF motion and is not ideal for the determination of CM-CF motion and degree-1 mass changes. We recently realized an experimental Terrestrial Reference Frame (TRF) through station time series using the Kalman filter and the RTS smoother. The TRF has its origin defined at nearly instantaneous CM using weekly SLR measurement time series. VLBI, GNSS and DORIS time series are combined weekly with those of SLR and tied to the geocentric (CM) reference frame through local tie measurements and co-motion constraints on co-located geodetic stations. The unified geocentric time series of the four geodetic techniques provide a much better network geometry for direct geodetic determination of geocenter motion. Results from this direct approach using a 90-station network compares favorably with those obtained from joint inversions of GPS/GRACE data and ocean bottom pressure models. We will also show that a previously identified discrepancy in X-component between direct SLR orbit-tracking and inverse determined geocenter motions is largely reconciled with the new unified network.

A preliminary geodetic data model for geographic information systems

NASA Astrophysics Data System (ADS)

Kelly, K. M.

2009-12-01

Our ability to gather and assimilate integrated data collections from multiple disciplines is important for earth system studies. Moreover, geosciences data collection has increased dramatically, with pervasive networks of observational stations on the ground, in the oceans, in the atmosphere and in space. Contemporary geodetic observations from several space and terrestrial technologies contribute to our knowledge of earth system processes and thus are a valuable source of high accuracy information for many global change studies. Assimilation of these geodetic observations and numerical models into models of weather, climate, oceans, hydrology, ice, and solid Earth processes is an important contribution geodesists can make to the earth science community. Clearly, the geodetic observations and models are fundamental to these contributions. ESRI wishes to provide leadership in the geodetic community to collaboratively build an open, freely available content specification that can be used by anyone to structure and manage geodetic data. This Geodetic Data Model will provide important context for all geographic information. The production of a task-specific geodetic data model involves several steps. The goal of the data model is to provide useful data structures and best practices for each step, making it easier for geodesists to organize their data and metadata in a way that will be useful in their data analyses and to their customers. Built on concepts from the successful Arc Marine data model, we introduce common geodetic data types and summarize the main thematic layers of the Geodetic Data Model. These provide a general framework for envisioning the core feature classes required to represent geodetic data in a geographic information system. Like Arc Marine, the framework is generic to allow users to build workflow or product specific geodetic data models tailored to the specific task(s) at hand. This approach allows integration of the data with other existing geophysical datasets, thus facilitating creation of multi-tiered models. The Geodetic Data Model encourages data assimilation and analysis and facilitates data interoperability, coordination and integration in earth system modeling. It offers a basic set of data structures organized in a simple and homogeneous way and can streamline access to and processing of geodetic data. It can aid knowledge discovery through the use of GIS technology to enable identification and understanding of relationships and provide well-established tools and methods to communicate complex technical knowledge with non-specialist audiences. The Geodetic Data Model comprise the base classes for using workflow driven ontology (WDO) techniques for specifying the computation of complex geodetic products along with the ability to capture provenance information. While we do not specify WDO for any given geodetic product, we recognize that structured geodetic data is essential for generating any geodetic WDO, a task that can be streamlined in some GIS software.

Dislocation model for aseismic fault slip in the transverse ranges of Southern California

NASA Technical Reports Server (NTRS)

Cheng, A.; Jackson, D. D.; Matsuura, M.

1985-01-01

Geodetic data at a plate boundary can reveal the pattern of subsurface displacements that accompany plate motion. These displacements are modelled as the sum of rigid block motion and the elastic effects of frictional interaction between blocks. The frictional interactions are represented by uniform dislocation on each of several rectangular fault patches. The block velocities and fault parameters are then estimated from geodetic data. Bayesian inversion procedure employs prior estimates based on geological and seismological data. The method is applied to the Transverse Ranges, using prior geological and seismological data and geodetic data from the USGS trilateration networks. Geodetic data imply a displacement rate of about 20 mm/yr across the San Andreas Fault, while the geologic estimates exceed 30 mm/yr. The prior model and the final estimates both imply about 10 mm/yr crustal shortening normal to the trend of the San Andreas Fault. Aseismic fault motion is a major contributor to plate motion. The geodetic data can help to identify faults that are suffering rapid stress accumulation; in the Transverse Ranges those faults are the San Andreas and the Santa Susana.

A new unified approach to determine geocentre motion using space geodetic and GRACE gravity data

NASA Astrophysics Data System (ADS)

Wu, Xiaoping; Kusche, Jürgen; Landerer, Felix W.

2017-06-01

Geocentre motion between the centre-of-mass of the Earth system and the centre-of-figure of the solid Earth surface is a critical signature of degree-1 components of global surface mass transport process that includes sea level rise, ice mass imbalance and continental-scale hydrological change. To complement GRACE data for complete-spectrum mass transport monitoring, geocentre motion needs to be measured accurately. However, current methods of geodetic translational approach and global inversions of various combinations of geodetic deformation, simulated ocean bottom pressure and GRACE data contain substantial biases and systematic errors. Here, we demonstrate a new and more reliable unified approach to geocentre motion determination using a recently formed satellite laser ranging based geocentric displacement time-series of an expanded geodetic network of all four space geodetic techniques and GRACE gravity data. The unified approach exploits both translational and deformational signatures of the displacement data, while the addition of GRACE's near global coverage significantly reduces biases found in the translational approach and spectral aliasing errors in the inversion.

Construction Theory and Noise Analysis Method of Global CGCS2000 Coordinate Frame

NASA Astrophysics Data System (ADS)

Jiang, Z.; Wang, F.; Bai, J.; Li, Z.

2018-04-01

The definition, renewal and maintenance of geodetic datum has been international hot issue. In recent years, many countries have been studying and implementing modernization and renewal of local geodetic reference coordinate frame. Based on the precise result of continuous observation for recent 15 years from state CORS (continuously operating reference system) network and the mainland GNSS (Global Navigation Satellite System) network between 1999 and 2007, this paper studies the construction of mathematical model of the Global CGCS2000 frame, mainly analyzes the theory and algorithm of two-step method for Global CGCS2000 Coordinate Frame formulation. Finally, the noise characteristic of the coordinate time series are estimated quantitatively with the criterion of maximum likelihood estimation.

Imaging Cascadia coupling: optimal design for an offshore seafloor geodetic network

NASA Astrophysics Data System (ADS)

Evans, E. L.; Minson, S. E.

2017-12-01

The Cascadia subduction zone in the Pacific Northwest of the United States is known to produce MW≈9.2 earthquakes, and accompanying tsunamis every 600 years. An outstanding question in this region (as in most offshore subduction zones) is the degree to which the megathrust is locked (i.e., the coupling rate), and whether the locked zone extends to the trench, where onshore geodetic measurements cannot uniquely resolve strain accumulation. Seafloor geodetic techniques, such as acoustic ranging combined with GNSS positioning, are capable of providing unique observations of strain accumulation near the offshore trench of subduction zones. These observations may be used to constrain megathrust coupling rate and spatial distribution, and ultimately forecast the potential size and rupture pattern of a future subduction zone earthquake, with resolution beyond the capability of onshore observations alone. However, the high cost of seafloor geodesy limits the number of stations that may be deployed and monitored. Therefore, it is essential that deployed stations be positioned in such a way to provide the most informative data for resolving subduction zone coupling. We identify optimal seafloor observation locations by minimizing the Shannon Information Entropy of potential geodetic observation locations, given the current onshore geodetic network. Because coupling rate on the Cascadia megathrust depends on the relative convergence rate between the Juan de Fuca and North American plates, the most valuable location for a single seafloor geodetic station is west of the Juan de Fuca trench, on the Juan de Fuca plate itself. Subsequent optimal locations are also identified offshore, on the hanging wall near the trench. This approach provides a quantitative assessment of the value of seafloor observations: a single offshore observation provides 30 times the information gain of an additional onshore observation, and adding many (>50) onshore observations cannot provide the information gain of a single offshore observation.

Establishing a Modern Ground Network for Space Geodesy Applications

NASA Technical Reports Server (NTRS)

Pearlman, M.; Pavlis, E.; Altamimi, Z.; Noll, C.

2010-01-01

Ground-based networks of co-located space-geodesy techniques (VLBI, SLR, GLASS, DORIS) are the basis for the development and maintenance of the :International Terrestrial deference Frame (ITRE), which is the basis for our metric measurements of global change. The Global Geodetic Observing System (GGOS) within the International Association of Geodesy has established a task to develop a strategy to design, integrate and maintain the fundamental geodetic network and supporting infrastructure in a sustainable way to satisfy the long-term requirements for the reference frame. The GGOS goal is an origin definition at I mm or better and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components. These goals are based on scientific requirements to address sea level rise with confidence. As a first step, simulations focused on establishing the optimal global SLR and VLBI network, since these two techniques alone are sufficient to define the reference frame. The GLASS constellations will then distribute the reference frame to users anywhere on the Earth. Using simulated data to be collected by the future networks, we investigated various designs and the resulting accuracy in the origin, scale and orientation of the resulting ITRF. We present here the results of extensive simulation studies aimed at designing optimal global geodetic networks to support GGOS science products. Current estimates are the network will require 24 - 32 globally distributed co-location sites. Stations in the near global network will require geologically stable sites witla good weather, established infrastructure, and local support and personnel. EGOS will seek groups that are interested in participation. GGOS intends to issues a Call for Participation of groups that would like to take part in the network implementation and operation_ Some examples of integrated stations currently in operation or under development will be presented. We will examine necessary conditions and challenges in designing a co-location station.

An Analysis of Strain Accumulation in the Western Part of Black Sea Region in Turkey

NASA Astrophysics Data System (ADS)

Deniz, I.; Avsar, N. B.; Deniz, R.; Mekik, C.; Kutoglu, S.

2014-12-01

Turkish National Horizontal Control Network (TNHCN) based on the European Datum 1950 (ED50) was used as the principal geodetic network until 2005 in Turkey. Since 2005, Turkish Large Scale Map and Map Information Production Regulation have required that that all the densification points have been produced within the same datum of Turkish National Fundamental GPS Network (TNFGN) put into practise in 2002 and based on International Terrestrial Reference Frame (ITRF). Hence, the common points were produced in both European Datum 1950 (ED50), and TNFGN.It is known that the geological and geophysical information about the network area can be obtained by the evaluation of the coordinate and scale variations in a geodetic network. For one such evaluation, the coordinate variations and velocities of network points, and also the strains are investigated. However, the principal problem in derivation of velocities arises from two different datums. In this context, the computation of velocities using the coordinate data of the ED50 and TNFGN is not accurate and reliable. Likewise, the analysis of strain from the coordinate differences is not reliable. However, due to the fact that the scale of a geodetic network is independent from datum, the strains can be derived from scale variations accurately and reliably.In this study, a test area limited 39.5°-42.0° northern latitudes and 31.0°-37.0° eastern longitudes was chosen. The benchmarks in this test area are composed of 30 geodetic control points derived with the aim of cadastral and engineering applications. We used data mining to investigate the common benchmarks in both reference systems for this area. Accordingly, the ED50 and TNFGN coordinates refer 1954 and 2005, respectively. Thus, it has been investigated the strain accumulation of 51 years in this region. It should be also noted that since 1954, the earthquakes have not registered greater than magnitude 6.0 in the test area. It is a considerable situation for this evaluation. The finite element analysis is used in order to derive the strain accumulation and rates in the test area (Figure 1). The results have been indicated that the minimum and maximum strains are 17μs and 3041μs, respectively.

RAEGE: An Atlantic Network of Geodynamical Fundamental Stations

NASA Technical Reports Server (NTRS)

Gonzalez, Jesus Gomez; Colomer, Francisco; LopezFernandez, Jose Antonio; Assis, Marlene C. S.

2010-01-01

Project RAEGE (Red Atlantica de Estaciones Geodinamicas y Espaciales) intends to set up a Spanish-Portuguese network of four Geodetic Fundamental Stations in Yebes (1), Canary Islands (1), and A cores Islands (2), as part of the developments needed for the IVS VLBI2010 scenario. It is envisaged that each Geodetic Fundamental Station will be equipped with one radio telescope of VLBI2010 specifications (at least 12-m diameter, fast slewing speed, but also able to operate up to 40 GHz), one gravimeter, one permanent GNSS station, and, at least at the Yebes site, one SLR facility. The National Geographical Institute of Spain (IGN) has experience in VLBI, having been a member of the European VLBI Network since 1993 and being one of the founding institutions of the Joint Institute for VLBI in Europe (JIVE), and it has been participating in geodetic VLBI campaigns with the 14-m radio telescope in Yebes since 1995. A new 40-m radio telescope has been built and was recently put into operation. It regularly participates in IVS sessions. There is infrastructure available for the new stations at Yebes and the Canary Islands. An agreement between IGN, the Portuguese Geographical Institute (IGP), and the Regional Government of the A cores ensures that the RAEGE project can become a reality by 2013.

Uncertainty assessment in geodetic network adjustment by combining GUM and Monte-Carlo-simulations

NASA Astrophysics Data System (ADS)

Niemeier, Wolfgang; Tengen, Dieter

2017-06-01

In this article first ideas are presented to extend the classical concept of geodetic network adjustment by introducing a new method for uncertainty assessment as two-step analysis. In the first step the raw data and possible influencing factors are analyzed using uncertainty modeling according to GUM (Guidelines to the Expression of Uncertainty in Measurements). This approach is well established in metrology, but rarely adapted within Geodesy. The second step consists of Monte-Carlo-Simulations (MC-simulations) for the complete processing chain from raw input data and pre-processing to adjustment computations and quality assessment. To perform these simulations, possible realizations of raw data and the influencing factors are generated, using probability distributions for all variables and the established concept of pseudo-random number generators. Final result is a point cloud which represents the uncertainty of the estimated coordinates; a confidence region can be assigned to these point clouds, as well. This concept may replace the common concept of variance propagation and the quality assessment of adjustment parameters by using their covariance matrix. It allows a new way for uncertainty assessment in accordance with the GUM concept for uncertainty modelling and propagation. As practical example the local tie network in "Metsähovi Fundamental Station", Finland is used, where classical geodetic observations are combined with GNSS data.

Current Trends and Challenges in Satellite Laser Ranging

NASA Astrophysics Data System (ADS)

Appleby, Graham M.; Bianco, Giuseppe; Noll, Carey E.; Pavlis, Erricos C.; Pearlman, Michael R.

2016-12-01

Satellite Laser Ranging (SLR) is used to measure accurately the distance from ground stations to retro-reflectors on satellites and on the Moon. SLR is one of the fundamental space-geodetic techniques that define the International Terrestrial Reference Frame (ITRF), which is the basis upon which many aspects of global change over space, time, and evolving technology are measured; with VLBI the two techniques define the scale of the ITRF; alone the SLR technique defines its origin (geocenter). The importance of the reference frame has recently been recognized at the inter-governmental level through the United Nations, which adopted in February 2015 the Resolution "Global Geodetic Reference Frame for Sustainable Development." Laser Ranging provides precision orbit determination and instrument calibration and validation for satellite-borne altimeters for the better understanding of sea level change, ocean dynamics, ice mass-balance, and terrestrial topography. It is also a tool to study the dynamics of the Moon and fundamental constants and theories. With the exception of the currently in-orbit GPS constellation, all GNSS satellites now carry retro-reflectors for improved orbit determination, harmonization of reference frames, and in-orbit co-location and system performance validation; the next generation of GPS satellites due for launch from 2019 onwards will also carry retro-reflectors. The ILRS delivers weekly realizations that are accumulated sequentially to extend the ITRF and the Earth Orientation Parameter series with a daily resolution. SLR technology continues to evolve towards the next-generation laser ranging systems and it is expected to successfully meet the challenges of the GGOS2020 program for a future Global Space Geodetic Network. Ranging precision is improving as higher repetition rate, narrower pulse lasers, and faster detectors are implemented within the network. Automation and pass interleaving at some stations is expanding temporal coverage and greatly enhancing efficiency. Discussions are ongoing with some missions that will allow the SLR network stations to provide crucial, but energy-safe, range measurements to optically vulnerable satellites. New retro-reflector designs are improving the signal link and enable daylight ranging that is now the norm for many stations. We discuss many of these laser ranging activities and some of the tough challenges that the SLR network currently faces.

The most remote point method for the site selection of the future GGOS network

NASA Astrophysics Data System (ADS)

Hase, Hayo; Pedreros, Felipe

2014-10-01

The Global Geodetic Observing System (GGOS) proposes 30-40 geodetic observatories as global infrastructure for the most accurate reference frame to monitor the global change. To reach this goal, several geodetic observatories have upgrade plans to become GGOS stations. Most initiatives are driven by national institutions following national interests. From a global perspective, the site distribution remains incomplete and the initiatives to improve this are up until now insufficient. This article is a contribution to answer the question on where to install new GGOS observatories and where to add observation techniques to existing observatories. It introduces the iterative most remote point (MRP) method for filling in the largest gaps in existing technique-specific networks. A spherical version of the Voronoi-diagram is used to pick the optimal location of the new observatory, but practical concerns determine its realistic location. Once chosen, the process is iterated. A quality and a homogeneity parameter of global networks measure the progress of improving the homogeneity of the global site distribution. This method is applied to the global networks of VGOS, and VGOS co-located with SLR to derive some clues about where additional observatory sites or additional observation techniques at existing observatories will improve the GGOS network configuration. With only six additional VGOS-stations, the homogeneity of the global VGOS-network could be significantly improved by more than . From the presented analysis, 25 known or new co-located VGOS and SLR sites are proposed as the future GGOS backbone: Colombo, Easter Island, Fairbanks, Fortaleza, Galapagos, GGAO, Hartebeesthoek, Honiara, Ibadan, Kokee Park, La Plata, Mauritius, McMurdo, Metsahövi, Ny Alesund, Riyadh, San Diego, Santa Maria, Shanghai, Syowa, Tahiti, Tristan de Cunha, Warkworth, Wettzell, and Yarragadee.

Evaluation of the Horizontal and Vertical Accuracy of GNSS Survey Observations from a Real-Time Network

NASA Astrophysics Data System (ADS)

Allahyari, M.; Olsen, M. J.; Gillins, D. T.; Dennis, M. L.

2016-12-01

Many current surveying standards in the United States require several long-duration, static Global Navigation Satellite System (GNSS) observations to derive high-accuracy geodetic coordinates. However, over the past decade, many entities have established real-time GNSS networks (RTNs), which could reduce the field time for establishing geodetic control from hours to minutes. To evaluate the accuracy of RTN GNSS observations, data collected from two National Geodetic Survey (NGS) surveys in South Carolina and Oregon were studied. The objectives were to: 1) determine the accuracy of a real-time observation as a function of duration; 2) examine the influence of including GLONASS (Russia's version of GPS); 3) compare results using a single base to the full RTN network solution; and 4) assess the effect of baseline length on accuracy. In South Carolina, 360 observations ranging from 5 to 600 seconds were collected on 20 passive marks using RTN and single-base solutions, both with GPS+GLONASS and GPS-only. In Oregon, 18 passive marks were observed from 5 to 900 seconds using GPS-only with the RTN, and with GPS+GLONASS and GPS-only from a single-base. To develop "truth" coordinates, at least 30 hours of static GPS data were also collected on all marks. Each static survey session was post-processed in OPUS-Projects, and the resulting vectors were used to build survey networks that were least-squares adjusted using the NGS software ADJUST. The resulting coordinates provided the basis for evaluating the accuracy of the real-time observations. Results from this study indicate great potential in the use of RTNs for accurate derivation of geodetic coordinates. Both case studies showed an optimal observation duration of 180 seconds. RTN data tended to be more accurate and consistent than single-base data, and GLONASS slightly improved accuracy. A key benefit of GLONASS was the ability to obtain more fixed solutions at longer baseline lengths than single-base solutions.

Testing deformation hypotheses by constraints on a time series of geodetic observations

NASA Astrophysics Data System (ADS)

Velsink, Hiddo

2018-01-01

In geodetic deformation analysis observations are used to identify form and size changes of a geodetic network, representing objects on the earth's surface. The network points are monitored, often continuously, because of suspected deformations. A deformation may affect many points during many epochs. The problem is that the best description of the deformation is, in general, unknown. To find it, different hypothesised deformation models have to be tested systematically for agreement with the observations. The tests have to be capable of stating with a certain probability the size of detectable deformations, and to be datum invariant. A statistical criterion is needed to find the best deformation model. Existing methods do not fulfil these requirements. Here we propose a method that formulates the different hypotheses as sets of constraints on the parameters of a least-squares adjustment model. The constraints can relate to subsets of epochs and to subsets of points, thus combining time series analysis and congruence model analysis. The constraints are formulated as nonstochastic observations in an adjustment model of observation equations. This gives an easy way to test the constraints and to get a quality description. The proposed method aims at providing a good discriminating method to find the best description of a deformation. The method is expected to improve the quality of geodetic deformation analysis. We demonstrate the method with an elaborate example.

Low-Cost GNSS Receivers for Local Monitoring: Experimental Simulation, and Analysis of Displacements

PubMed Central

Biagi, Ludovico; Grec, Florin Cătălin; Negretti, Marco

2016-01-01

The geodetic monitoring of local displacements and deformations is often needed for civil engineering structures and natural phenomena like, for example, landslides. A local permanent GNSS (Global Navigation Satellite Systems) network can be installed: receiver positions in the interest area are estimated and monitored with respect to reference stations. Usually, GNSS geodetic receivers are adopted and provide results with accuracies at the millimeter level: however, they are very expensive and the initial cost and the risk of damage and loss can discourage this approach. In this paper the accuracy and the reliability of low-cost u-blox GNSS receivers are experimentally investigated for local monitoring. Two experiments are analyzed. In the first, a baseline (65 m long) between one geodetic reference receiver and one u-blox is continuously observed for one week: the data are processed by hourly sessions and the results provide comparisons between two processing packages and a preliminary accuracy assessment. Then, a network composed of one geodetic and two u-blox receivers is set up. One u-blox is installed on a device (slide) that allows to apply controlled displacements. The geodetic and the other u-blox (at about 130 m) act as references. The experiment lasts about two weeks. The data are again processed by hourly sessions. The estimated displacements of the u-blox on the slide are analyzed and compared with the imposed displacements. All of the results are encouraging: in the first experiment the standard deviations of the residuals are smaller than 5 mm both in the horizontal and vertical; in the second, they are slightly worse but still satisfactory (5 mm in the horizontal and 13 mm in vertical) and the imposed displacements are almost correctly identified. PMID:27983707

Low-Cost GNSS Receivers for Local Monitoring: Experimental Simulation, and Analysis of Displacements.

PubMed

Biagi, Ludovico; Grec, Florin Cătălin; Negretti, Marco

2016-12-15

The geodetic monitoring of local displacements and deformations is often needed for civil engineering structures and natural phenomena like, for example, landslides. A local permanent GNSS (Global Navigation Satellite Systems) network can be installed: receiver positions in the interest area are estimated and monitored with respect to reference stations. Usually, GNSS geodetic receivers are adopted and provide results with accuracies at the millimeter level: however, they are very expensive and the initial cost and the risk of damage and loss can discourage this approach. In this paper the accuracy and the reliability of low-cost u-blox GNSS receivers are experimentally investigated for local monitoring. Two experiments are analyzed. In the first, a baseline (65 m long) between one geodetic reference receiver and one u-blox is continuously observed for one week: the data are processed by hourly sessions and the results provide comparisons between two processing packages and a preliminary accuracy assessment. Then, a network composed of one geodetic and two u-blox receivers is set up. One u-blox is installed on a device (slide) that allows to apply controlled displacements. The geodetic and the other u-blox (at about 130 m) act as references. The experiment lasts about two weeks. The data are again processed by hourly sessions. The estimated displacements of the u-blox on the slide are analyzed and compared with the imposed displacements. All of the results are encouraging: in the first experiment the standard deviations of the residuals are smaller than 5 mm both in the horizontal and vertical; in the second, they are slightly worse but still satisfactory (5 mm in the horizontal and 13 mm in vertical) and the imposed displacements are almost correctly identified.

Optimizing the African VLBI Network for Astronomy and Geodesy

NASA Astrophysics Data System (ADS)

de Witt, A.; Mayer, D.; MacLeod, G.; Combrinck, L.; Petrov, L.; Nickola, M.

2016-12-01

The African VLBI Network will be a pan-African network of radio telescopes comprised of converted redundant satellite Earth-station antennas and new purpose-built radio telescopes. The first of these antennas, in Ghana, is currently being converted to a radio telescope and current funding is estimated to permit the conversion of two more antennas in Africa. These antennas will initially be equipped with a 5-GHz and 6.7-GHz receiver and the next receiver likely to be fitted is a 1.4-1.7-GHz receiver. While it would be advantageous for the AVN antennas to be able to participate also in geodetic and astrometric VLBI observations, there is no funding currently for this. In this paper we re-visit the scientific justifications for the AVN in an attempt to optimize the AVN for each science case, both astronomical and geodetic.

Analysis of ILRS Site Ties

NASA Astrophysics Data System (ADS)

Husson, V. S.; Long, J. L.; Pearlman, M.

2001-12-01

By the end of 2000, 94% of ILRS stations had completed station and site information forms (i.e. site logs). These forms contain six types of information. These six categories include site identifiers, contact information, approximate coordinates, system configuration history, system ranging capabilities, and local survey ties. The ILRS Central Bureau, in conjunction with the ILRS Networks and Engineering Working Group, has developed procedures to quality control site log contents. Part of this verification entails data integrity checks of local site ties and is the primary focus of this paper. Local survey ties are critical to the combination of space geodetic network coordinate solutions (i.e. GPS, SLR, VLBI, DORIS) of the International Terrestrial Reference Frame (ITRF). Approximately 90% of active SLR sites are collocated with at least one other space geodetic technique. The process used to verify these SLR ties, at collocated sites, is identical to the approach used in ITRF2000. Local vectors (X, Y, Z) from each ILRS site log are differenced from its corresponding ITRF2000 position vectors (i.e. no transformations). These X, Y, and Z deltas are converted into North, East, and Up. Any deltas, in any component, larger than 5 millimeter is flagged for investigation. In the absence of ITRF2000 SLR positions, CSR positions were used. To further enhance this comparison and to fill gaps in information, local ties contained in site logs from the other space geodetic services (i.e. IGS, IVS, IDS) were used in addition to ITRF2000 ties. Case studies of two collocated sites (McDonald/Ft. Davis and Hartebeeshtoek) will be explored in-depth. Recommendations on how local site surveys should be conducted and how this information should be managed will also be presented.

Geodetic results in Afar: The rifting episode of November 1978 in the Asal-Ghoubbet rift

NASA Astrophysics Data System (ADS)

Kasser, M.; Lepine, J. C.; Ruegg, J. C.; Tarantula, A.

1981-01-01

A seismo-tectonic and volcanic crisis occurred in November 1978 in the Asal-Ghoubbet rift, first subaerial section of the accreting plate boundary between the African and Arabian plates (Allard et al., 1979; Abdallah et al., 1979; Le Dain et al., 1980). The activity was located in the center of a geodetic network set up in the winter 1972-1973 by the Institut Géographique National in collaboration with the Institut de Physique du Globe de Paris. Simultaneously, a precise levelling line of about 100 km was established across the area (I.G.N., 1973). The resurveying of both the geodetic network and the levelling line was carried out after the crisis, between November 1978 and March 1979. Extensions up to 2.4 m and vertical displacements up to 0.7 m were measured. Operating techniques and results of the resurveying are described in Kasser et al. (1979) and Ruegg et al. (1979). Figure 1 shows the horizontal displacements (relating to point B and to the direction BT) and figure 2 shows the vertical displacements relating to the two external points. Tarantola et al. (1979, 1980) have shown that these results can be geodynamically interpreted by a mechanism of sudden breaking and elastic rebound after an elastic stretching of the crust due to the relative drift of the plates. The breaking is triggered by magmatic fracturing of the crust, with dykes injection from a magmatic chamber which has fed the basaltic fissurai eruption. The horizontal and vertical displacements outside the broken zone of the Inner Floor are predicted by a numerical model based on this interpretation which fit very well the experimental data.

GPS Monitoring of Surface Change During and Following the Fortuitous Occurrence of the M(sub w) = 7.3 Landers Earthquake in our Network

NASA Technical Reports Server (NTRS)

Miller, M. Meghan

1998-01-01

Accomplishments: (1) Continues GPS monitoring of surface change during and following the fortuitous occurrence of the M(sub w) = 7.3 Landers earthquake in our network, in order to characterize earthquake dynamics and accelerated activity of related faults as far as 100's of kilometers along strike. (2) Integrates the geodetic constraints into consistent kinematic descriptions of the deformation field that can in turn be used to characterize the processes that drive geodynamics, including seismic cycle dynamics. In 1991, we installed and occupied a high precision GPS geodetic network to measure transform-related deformation that is partitioned from the Pacific - North America plate boundary northeastward through the Mojave Desert, via the Eastern California shear zone to the Walker Lane. The onset of the M(sub w) = 7.3 June 28, 1992, Landers, California, earthquake sequence within this network poses unique opportunities for continued monitoring of regional surface deformation related to the culmination of a major seismic cycle, characterization of the dynamic behavior of continental lithosphere during the seismic sequence, and post-seismic transient deformation. During the last year, we have reprocessed all three previous epochs for which JPL fiducial free point positioning products available and are queued for the remaining needed products, completed two field campaigns monitoring approx. 20 sites (October 1995 and September 1996), begun modeling by development of a finite element mesh based on network station locations, and developed manuscripts dealing with both the Landers-related transient deformation at the latitude of Lone Pine and the velocity field of the whole experiment. We are currently deploying a 1997 observation campaign (June 1997). We use GPS geodetic studies to characterize deformation in the Mojave Desert region and related structural domains to the north, and geophysical modeling of lithospheric behavior. The modeling is constrained by our existing and continued GPS measurements, which will provide much needed data on far-field strain accumulation across the region and on the deformational response of continental lithosphere during and following a large earthquake, forming the basis for kinematic and dynamic modeling of secular and seismic-cycle deformation. GPS geodesy affords both regional coverage and high precision that uniquely bear on these problems.

Mathematical Modelling of the Behavior of the Lacoste and Romberg ’G’ Gravity Meter for Use in Gravity Network Adjustments and Data Analyses,

DTIC Science & Technology

1981-11-01

Geodetic Science and Surveying 62101F The Ohio State University 760003AL Columbus, Ohio 43210 11. CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE Air ... Air Force Contract No. F19628-79-C-9975, The Ohio State University Research Foundation, Project No. 711715, Project Supervisor, Urho A. Uotila...Professor, Department of Geodetic Science and Surveying. The contract covering this research is administered by the Air Force Geophysics Laboratory (AFGL

Effect of horizontal displacements due to ocean tide loading on the determination of polar motion and UT1

NASA Astrophysics Data System (ADS)

Scherneck, Hans-Georg; Haas, Rüdiger

We show the influence of horizontal displacements due to ocean tide loading on the determination of polar motion and UT1 (PMU) on the daily and subdaily timescale. So called ‘virtual PMU variations’ due to modelling errors of ocean tide loading are predicted for geodetic Very Long Baseline Interferometry (VLBI) networks. This leads to errors of subdaily determination of PMU. The predicted effects are confirmed by the analysis of geodetic VLBI observations.

Geolocation Support for Water Supply and Sewerage Projects in Azerbaijan

NASA Astrophysics Data System (ADS)

Qocamanov, M. H.; Gurbanov, Ch. Z.

2016-10-01

Drinking water supply and sewerage system designing and reconstruction projects are being extensively conducted in Azerbaijan Republic. During implementation of such projects, collecting large amount of information about the area and detailed investigations are crucial. Joint use of the aerospace monitoring and GIS play an essential role for the studies of the impact of environmental factors, development of the analytical information systems and others, while achieving the reliable performance of the existing and designed major water supply pipelines, as well as construction and exploitation of the technical installations. With our participation the GIS has been created in "Azersu" OJSC that includes systematic database of the drinking water supply and sewerage system, and rain water networks to carry out necessary geo information analysis. GIScreated based on "Microstation" platform and aerospace data. Should be mentioned that, in the country, specifically in large cities (i.e. Baku, Ganja, Sumqait, etc.,) drinking water supply pipelines cross regions with different physico-geographical conditions, geo-morphological compositions and seismotectonics.Mains water supply lines in many accidents occur during the operation, it also creates problems with drinking water consumers. In some cases the damage is caused by large-scale accidents. Long-term experience gives reason to say that the elimination of the consequences of accidents is a major cost. Therefore, to avoid such events and to prevent their exploitation and geodetic monitoring system to improve the rules on key issues. Therefore, constant control of the plan-height positioning, geodetic measurements for the detailed examination of the dynamics, repetition of the geodetic measurements for certain time intervals, or in other words regular monitoring is very important. During geodetic monitoring using the GIS has special significance. Given that, collecting geodetic monitoring measurements of the main pipelines on the same coordinate system and processing these data on a single GIS system allows the implementation of overall assessment of plan-height state of major water supply pipeline network facilities and the study of the impact of water supply network on environment and alternatively, the impact of natural processes on major pipeline.

Plate motions and deformations from geologic and geodetic data

NASA Technical Reports Server (NTRS)

Jordan, Thomas H.

1990-01-01

An analysis of geodetic data in the vicinity of the Crustal Dynamics Program (CDP) site at Vandenberg Air Force Base (VNDN) is presented. The utility of space-geodetic data in the monitoring of transient strains associated with earthquakes in tectonically active areas like California is investigated. Particular interest is in the possibility that space-geodetic methods may be able to provide critical new data on deformations precursory to large seismic events. Although earthquake precursory phenomena are not well understood, the monitoring of small strains in the vicinity of active faults is a promising technique for studying the mechanisms that nucleate large earthquakes and, ultimately, for earthquake prediction. Space-geodetic techniques are now capable of measuring baselines of tens to hundreds of kilometers with a precision of a few parts in 108. Within the next few years, it will be possible to record and analyze large-scale strain variations with this precision continuously in real time. Thus, space-geodetic techniques may become tools for earthquake prediction. In anticipation of this capability, several questions related to the temporal and spatial scales associated with subseismic deformation transients are examined.

Abstracts for the October 2012 meeting on Volcanism in the American Southwest, Flagstaff, Arizona

USGS Publications Warehouse

Lowenstern, Jacob B.

2013-01-01

Though volcanic eruptions are comparatively rare in the American Southwest, the States of Arizona, Colorado, New Mexico, Nevada, and Utah host Holocene volcanic eruption deposits and are vulnerable to future volcanic activity. Compared with other parts of the western United States, comparatively little research has been focused on this area, and eruption probabilities are poorly constrained. Monitoring infrastructure consists of a variety of local seismic networks, and ”backbone“ geodetic networks with little integration. Emergency response planning for volcanic unrest has received little attention by either Federal or State agencies. On October 18–20, 2012, 90 people met at the U.S. Geological Survey campus in Flagstaff, Arizona, providing an opportunity for volcanologists, land managers, and emergency responders to meet, converse, and begin to plan protocols for any future activity. Geologists contributed data on recent findings of eruptive ages, eruption probabilities, and hazards extents (plume heights, ash dispersal). Geophysicists discussed evidence for magma intrusions from seismic, geodetic, and other geophysical techniques. Network operators publicized their recent work and the relevance of their equipment to volcanic regions. Land managers and emergency responders shared their experiences with emergency planning for earthquakes. The meeting was organized out of the recognition that little attention had been paid to planning for or mitigation of volcanic hazards in the American Southwest. Moreover, few geological meetings have hosted a session specifically devoted to this topic. This volume represents one official outcome of the meeting—a collection of abstracts related to talks and poster presentations shared during the first two days of the meeting. In addition, this report includes the meeting agenda as a record of the proceedings. One additional intended outcome will be greater discussion and coordination among emergency responders, geologists, geophysicists, and land managers regarding geologic hazards in the Southwest.

A stress-constrained geodetic inversion method for spatiotemporal slip of a slow slip event with earthquake swarm

NASA Astrophysics Data System (ADS)

Hirose, H.; Tanaka, T.

2017-12-01

Geodetic inversions have been performed by using GNSS data and/or tiltmeter data in order to estimate spatio-temporal fault slip distributions. They have been applied for slow slip events (SSEs), which are episodic fault slip lasting for days to years (e.g., Ozawa et al., 2001; Hirose et al., 2014). Although their slip distributions are important information in terms of inferring strain budget and frictional characteristics on a subduction plate interface, inhomogeneous station coverage generally yields spatially non-uniform slip resolution, and in a worse case, a slip distribution can not be recovered. It is known that an SSE which accompanies an earthquake swarm around the SSE slip area, such as the Boso Peninsula SSEs (e.g., Hirose et al., 2014). Some researchers hypothesize that these earthquakes are triggered by a stress change caused by the accompanying SSE (e.g., Segall et al., 2006). Based on this assumption, it is possible that a conventional geodetic inversion which impose a constraint on the stress change that promotes earthquake activities may improve the resolution of the slip distribution. Here we develop an inversion method based on the Network Inversion Filter technique (Segall and Matthews, 1997), incorporating a constraint on a positive change in Coulomb failure stress (Delta-CFS) at the accompanied earthquakes. In addition, we apply this new method to synthetic data in order to check the effectiveness of the method and the characteristics of the inverted slip distributions. The results show that there is a case in which the reproduction of a slip distribution is better with earthquake information than without it. That is, it is possible to improve the reproducibility of a slip distribution of an SSE with this new inversion method if an earthquake catalog for the accompanying earthquake activity can be used when available geodetic data are insufficient.

The interpretation of crustal dynamics data in terms of plate interactions and active tectonics of the Anatolian plate and surrounding regions in the Middle East

NASA Technical Reports Server (NTRS)

Toksoz, M. Nafi; Reilinger, Robert

1992-01-01

A detailed study was made of the consequences of the Arabian plate convergence against Eurasia and its effects on the tectonics of Anatolia and surrounding regions of the eastern Mediterranean. A primary source of information is time rates of change of baseline lengths and relative heights determined by repeated SLR measurements. These SLR observations are augmented by a network of GPS stations in Anatolia, Aegea, and Greece, established and twice surveyed since 1988. The existing SLR and GPS networks provide the spatial resolution necessary to reveal the details of ongoing tectonic processes in this area of continental collision. The effort has involved examining the state of stress in the lithosphere and relative plate motions as revealed by these space based geodetic measurements, seismicity, and earthquake mechanisms as well as the aseismic deformations of the plates from conventional geodetic data and geological evidence. These observations are used to constrain theoretical calculations of the relative effects of: (1) the push of the Arabian plate; (2) high topography of Eastern Anatolia; (3) the geometry and properties of African-Eurasian plate boundary; (4) subduction under the Hellenic Arc and southwestern Turkey; and (5) internal deformation and rotation of the Anatolian plate.

A Real-time, Borehole, Geophysical Observatory Above The Cascadia Subduction Zone

NASA Astrophysics Data System (ADS)

Collins, J. A.; McGuire, J. J.; Becker, K.; O'Brien, J. K.; von der Heydt, K.; Heesemann, M.; Davis, E. E.

2017-12-01

In July 2016, a team from WHOI and RSMAS installed a suite of seismic, geodetic and geothermal sensors in IODP borehole U1364A on the Cascadia Accretionary Prism offshore Vancouver Island. The borehole observatory was connected to the Clayoquot Slope node of the Ocean Networks Canada NEPTUNE Observatory in June 2017. The 3 km long extension cable provides power, timing, and internet connectivity. The borehole sits 4 km above the subduction zone thrust interface, and when drilled in 2010 was instrumented with an ACORK (Advanced Circulation Obviation Retrofit Kit) that allows monitoring and sampling of fluids from multiple zones within the 330 m drilled formation. The borehole ground-motion sensors consist of a broadband seismometer and two geodetic-quality (nano-radian resolution) two-axis tilt sensors clamped to the borehole casing wall at a depth of 277 m below the seafloor. The tilt sensors were selected to detect non-seismic, strain-related transients. A 24-thermistor cable extends from the seafloor to just above the seismometer and tilt-sensor package. The seismic and geodetic data have been flowing from the observatory (network code NV, station code CQS64, location codes B1, B2, and B3) since June and are available from the IRIS DMC. Initial inspection of the seismic and geodetic data shows that all sensors are operating well. We will report on station performance and detection thresholds using an anticipated 5 month duration data set.

How prepared were the Puerto Rico Seismic Network sites for the arrival of Hurricane Maria? Lessons learned on communications, power and infrastructure.

NASA Astrophysics Data System (ADS)

Vanacore, E. A.; Lopez, A. M.; Huerfano, V.; Lugo, J.; Baez-Sanchez, G.

2017-12-01

For exactly 85 years the island of Puerto Rico in the northeastern Caribbean was spared from catastrophic category 4 hurricane winds. Then Hurricane Maria arrived on September 20, 2017 with maximum sustained winds of up to 155 mph. The eye of the hurricane crossed the island from southeast to northwest in eight hours leaving almost a meter of rainfall on its path. Sustained winds, gusts and precipitation were most certainly going to affect the seismic and geodetic equipment the Puerto Rico Seismic Network (PRSN) use for locating earthquakes in the region. PRSN relies on 35 seismic stations (velocity and strong-motion) to characterize the seismic behavior of the island and 15 geodetic (GNSS) stations to determine crustal deformation of the Puerto Rico - Virgin Islands microplate. PRSN stations have been designed to withstand earthquakes. However, the equipment suffered considerable damage due to the strong winds especially station communication towers. This coupled with catastrophic damage to the telecommunication and power grids of the island had severe effects on the network. Additionally, the level of devastation was such that it hampered the ability of PRSN staff to visit the sites for assessment and repair. Here we present the effects of category 4 hurricane had on our seismic and geodetic sites, examine the susceptibility of the PRSN stations' power and communications, and discuss future plans to recuperate and improve station resiliency for future catastrophic events. These lessons learned hopefully will help harden sites of networks, agencies and/or institutions that rely on similar infrastructure.

Evaluation of the deformation parameters of the northern part of Eg

NASA Astrophysics Data System (ADS)

Mohamed, Abdel-Monem S.; Radwan, Ali M.; Sharf, Mohamed; Hamimi, Zakaria; Hegazy, Esraa E.; Abou Aly, Nadia; Gomaa, Mahmoud

2016-06-01

The northern part of Egypt is a rapidly growing development accompanied by the increased levels of standard living particularly in its urban areas. From tectonic and seismic point of views, the northern part of Egypt is one of the interested regions. It shows an active geologic structure attributed to the tectonic movements of the African and Eurasian plates from one side and the Arabian plate from the other side. From historical point of view and recent instrumental records, the northern part of Egypt is one of the seismo-active regions in Egypt. The investigations of the seismic events and their interpretations had led to evaluate the seismic hazard for disaster mitigation, for the safety of the densely populated regions and the vital projects. In addition to the monitoring of the seismic events, the most powerful technique of Global Navigation Satellite System (GNSS) will be used in determining crustal deformation where a geodetic network covers the northern part of Egypt. Joining the GPS Permanent stations of the northern part of Egypt with the Southern part of Europe will give a clear picture about the recent crustal deformation and the African plate velocity. The results from the data sets are compared and combined in order to determine the main characteristics of the deformation and hazard estimation for specified regions. Final compiled output from the seismological and geodetic analysis will throw lights upon the geodynamical regime of these seismo-active regions. This work will throw lights upon the geodynamical regime and to delineate the crustal stress and strain fields in the study region. This also enables to evaluate the active tectonics and surface deformation with their directions from repeated geodetic observations. The results show that the area under study suffers from continuous seismic activity related to the crustal movements taken place along trends of major faults

Geodetic measurement of deformation in California. Ph.D. Thesis - Massachusetts Inst. of Technology

NASA Technical Reports Server (NTRS)

Sauber, Jeanne

1989-01-01

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 as part of the NASA Crustal Dynamics Project provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI-derived rates of deformation requires an examination of geologic information and more densely sampled ground-based geodetic data. In the first two of three related studies, triangulation and trilateration data measured on two regional networks, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault, have been processed. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data have been utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geological structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. In a third study, the geocentric position vectors from a set of 77 VLBI experiments beginning in October 1982 have been used to estimate the tangential rate of change of station positions in the western U.S. in a North-America-Fixed reference frame.

Incorporation of Multiple Datasets in Earthquake Source Inversions: Case Study for the 2015 Illapel Earthquake

NASA Astrophysics Data System (ADS)

Williamson, A.; Cummins, P. R.; Newman, A. V.; Benavente, R. F.

2016-12-01

The 2015 Illapel, Chile earthquake was recorded over a wide range of seismic, geodetic and oceanographic instruments. The USGS assigned magnitude 8.3 earthquake produced a tsunami that was recorded trans-oceanically at both tide gauges and deep-water tsunami pressure sensors. The event also generated surface deformation along the Chilean coast that was recovered through ascending and descending paths of the Sentinel-1A satellite. Additionally, seismic waves were recorded across various global seismic networks. While the determination of the rupture source through seismic and geodetic means is now commonplace and has been studied extensively in this fashion for the Illapel event, the use of tsunami datasets in the inversion process, rather than purely as a forward validation of models, is less common. In this study, we evaluate the use of both near and far field tsunami pressure gauges in the source inversion process, examining their contribution to seismic and geodetic joint inversions- as well as examine the contribution of dispersive and elastic loading parameters on the numerical tsunami propagation. We determine that the inclusion of near field tsunami pressure gauges assists in resolving the degree of slip in the near-trench environment, where purely geodetic inversions lose most resolvability. The inclusion of a far-field dataset has the potential to add further confidence to tsunami inversions, however at a high computational cost. When applied to the Illapel earthquake, this added near-trench resolvability leads to a better estimation of tsunami arrival times at near field gauges and contributes understanding to the wide variation in tsunamigenic slip present along the highly active Peru-Chile trench.

Possible tectonomagnetic effect observed from mid-1989, to mid-1990, in Long Valley Caldera, California

USGS Publications Warehouse

Mueller, R.J.; Johnston, M.J.S.; Langbein, J.O.

1991-01-01

Precise measurements of local magnetic fields have been obtained with a differentially connected array of three proton magnetometers in the Long Valley Caldera region since 1984. After correction for secular variation, it is apparent that an anomalous 2 nT decrease in the magnetic field occurred from mid-1989 to mid-1990 at the magnetometer located closed to the center of the resurgent dome inside the caldera. During this period a significant increase in geodetic strain rate of 8.5 ppm/a was observed on the two-color geodimeter network within the caldera from October, 1989, to mid-1990 and a dramatic increase in seismic activity occurred from December, 1989 to July, 1990. A simple dilatational point-source model with pressure increasing by 52 Mpa from October 1989 to August 1990 at a depth of about 7 km beneath the center of the resurgent dome can be fit to the strain data. Magnetic, seismic and geodetic data suggest that an episode of active magmatic intrusion occurred from late 1989 to mid-1990 at a depth of about 7-8 km beneath the resurgent dome within the caldera. -from Authors

Centimeter repeatability of the VLBI estimates of European baselines

NASA Technical Reports Server (NTRS)

Rius, Antonio; Zarraoa, Nestor; Sardon, Esther; Ma, Chopo

1992-01-01

In the last three years, the European Geodetic Very Long Baseline Interferometry (VLBI) Network has grown to a total of six fixed antennas placed in Germany, Italy, Spain and Sweden, all equipped with the standard geodetic VLBI instrumentation and data recording systems. During this period of time, several experiments have been carried out using this interferometer providing data of very high quality due to the excellent sensitivity and performance of the European stations. The purpose of this paper is to study the consistency of the VLBI geodetic results on the European baselines with respect to the different degrees of freedom in the analysis procedure. Used to complete this study were both real and simulated data sets, two different software packages (OCCAM 3.0 and CALC 7.4/SOLVE), and a variety of data analysis strategies.

Verification of the Usefulness of the Trimble Rtx Extended Satellite Technology with the Xfill Function in the Local Network Implementing Rtk Measurements

NASA Astrophysics Data System (ADS)

Siejka, Zbigniew

2014-12-01

The paper presents the method of satellite measurements, which gives users the ability of GNSS continuous precise positioning in real time, even in the case of short interruptions in receiving the correction of the local ground system of measurements support. The proposed method is a combination of two satellite positioning technologies RTN GNSS and RTX Extended. In technology RTX Extended the xFill function was used for precise positioning in real time and in the local reference system. This function provides the ability to perform measurement without the need for constant communication with the ground support satellite system. Test measurements were performed on a test basis located in Krakow, and RTN GNSS positioning was done based on the national network of reference stations of the ASGEUPOS. The solution allows for short (up to 5 minutes) interruptions in radio or internet communication. When the primary stream of RTN correction is not available, then the global corrections Trimble xFill broadcasted by satellite are used. The new technology uses in the real-time data from the global network of tracking stations and contributes significantly to improving the quality and efficiency of surveying works. At present according to the authors, technology Trimble CenterPoint RTX can guarantee repeatability of measurements not worse than 3.8 cm (Trimble Survey Division, 2012). In the paper the comparative analysis of measurement results between the two technologies was performed: RTN carried out in the classic way, which was based on the corrections of the terrestrial local network of the Polish system of active geodetic network (ASG-EUPOS) and RTK xFill technology. The results were related to the data of test network, established as error free. The research gave satisfactory results and confirmed the great potential of the use of the new technology in the geodetic work realization. By combining these two technologies of GNSS surveying the user can greatly improve the overall performance of real-time positioning.

Recent surface displacements in the Upper Rhine Graben — Preliminary results from geodetic networks

NASA Astrophysics Data System (ADS)

Fuhrmann, Thomas; Heck, Bernhard; Knöpfler, Andreas; Masson, Frédéric; Mayer, Michael; Ulrich, Patrice; Westerhaus, Malte; Zippelt, Karl

2013-08-01

Datasets of the GNSS Upper Rhine Graben Network (GURN) and the national levelling networks in Germany, France and Switzerland are investigated with respect to current surface displacements in the Upper Rhine Graben (URG) area. GURN consists of about 80 permanent GNSS (Global Navigation Satellite Systems) stations. The terrestrial levelling network comprises 1st and 2nd order levelling lines that have been remeasured at intervals of roughly 25 years, starting in 1922. Compared to earlier studies national institutions and private companies made available raw data, allowing for consistent solutions for the URG region. We focussed on the southern and eastern parts of the investigation area. Our preliminary results show that the levelling and GNSS datasets are sensitive to resolve small surface displacement rates down to an order of magnitude of 0.2 mm/a and 0.4 mm/a, respectively. The observed horizontal velocity components for a test region south of Strasbourg, obtained from GNSS coordinate time series, vary around 0.5 mm/a. The results are in general agreement with interseismic strain built-up in a sinistral strike-slip regime. Since the accuracy of the GNSS derived vertical component is insufficient, data of precise levelling networks is used to determine vertical displacement rates. More than 75% of the vertical rates obtained from a kinematic adjustment of 1st order levelling lines in the eastern part of URG vary between - 0.2 mm/a and + 0.2 mm/a, indicating that this region behaves stable. Higher rates up to 0.5 mm/a in a limited region south of Freiburg are in general agreement with active faulting. We conclude that both networks deliver stable results that reflect real surface movements in the URG area. We note, however, that geodetically observed surface displacements generally result from a superposition of different effects, and that a separation in tectonic and non-tectonic processes needs additional information and expertise.

On the methodology of Engineering Geodesy

NASA Astrophysics Data System (ADS)

Brunner, Fritz K.

2007-09-01

Textbooks on geodetic surveying usually describe a very small number of principles which should provide the foundation of geodetic surveying. Here, the author argues that an applied field, such as engineering geodesy, has a methodology as foundation rather than a few principles. Ten methodological elements (ME) are identified: (1) Point discretisation of natural surfaces and objects, (2) distinction between coordinate and observation domain, (3) definition of reference systems, (4) specification of unknown parameters and desired precisions, (5) geodetic network and observation design, (6) quality control of equipment, (7) quality control of measurements, (8) establishment of measurement models, (9) establishment of parameter estimation models, (10) quality control of results. Each ME consists of a suite of theoretical developments, geodetic techniques and calculation procedures, which will be discussed. This paper is to be considered a first attempt at identifying the specific elements of the methodology of engineering geodesy. A better understanding of this methodology could lead to an increased objectivity, to a transformation of subjective practical experiences into objective working methods, and consequently to a new structure for teaching this rather diverse subject.

COLD MAGICS - Continuous Local Deformation Monitoring of an Arctic Geodetic Fundamental Station

NASA Technical Reports Server (NTRS)

Haas, Ruediger; Bergstrand, Sten

2010-01-01

We describe the experience gained in a project to continuously monitor the local tie at the Geodetic Observatory Ny-Alesund. A PC-controlled robotic total station was used to monitor survey prisms that were attached to survey pillars of the local network and the monuments used for geodetic VLBI and GNSS measurements. The monitoring lasted for seven days and had a temporal resolution of six minutes. The raw angle and distance measurements show clear sinusoidal signatures with a daily period, most strongly for a four-day period with 24 hours of sunshine. The derived topocentric coordinates of the survey prisms attached to the GNSS monument and the VLBI radio telescope act as approximation for the local tie. We detect clear signatures at the mm-level. With the current approach we cannot distinguish between real motion of the prisms and potential thermal influences on the instrument used for the observations. However, the project shows that continuous local tie monitoring is feasible today and in the future can and should be used for all geodetic co-location stations.

Multi-parameter observations in the Ibero-Moghrebian region: the Western Mediterranean seismic network (WM) and ROA GPS geodynamic network

NASA Astrophysics Data System (ADS)

Pazos, Antonio; Martín Davila, José; Buforn, Elisa; Gárate Pasquín, Jorge; Catalán Morollón, Manuel; Hanka, Winfried; Udías, Agustín.; Benzzeghoud, Mourad; Harnafi, Mimoun

2010-05-01

The plate boundary between Eurasia and Africa plates crosses the called "Ibero-Maghrebian" region from the San Vicente Cape (SW Portugal) to Tunisia including the South of Iberia, Alboran Sea, and northern Morocco and Algeria. In this area, the convergence, with a low rate, is accommodated over a wide and diffuse deformation zone, characterized by a significant and widespread moderate seismic activity [Buforn et al., 1995], and the occurrence of large earthquakes is separated by long time intervals. Since more than hundred years ago San Fernando Naval Observatory (ROA), in collaboration with other Institutes, has deployed different geophysical and geodetic equipment in the Southern Spain - North-western Africa area in order to study this broad deformation zone. Currently a Broad Band seismic net (Western Mediterranean, WM net) is deployed, in collaboration with other institutions, around the Gulf of Cádiz and the Alboran sea, with stations in the South of Iberia and in North Africa (at Spanish places and Morocco), together with the seismic stations a permanent geodetic GPS net is co-installed at the same sites. Also, other geophysical instruments have been installed: a Satellite Laser Ranging (SLR) station at San Fernando Observatory Headquarter, a Geomagnetic Observatory in Cádiz bay area and some meteorological stations. These networks have been recently improved with the deployment of a new submarine and on-land geophysical observatory in the Alboran island (ALBO Observatory), where a permanent GPS, a meteorological station were installed on land and a permanent submarine observatory in 50 meters depth was also deploy in last October (with a broad band seismic sensor, a 3 C accelerometer and a DPG). This work shows the present status and the future plans of these networks and some results.

The Global Geodetic Observing System: Recent Activities and Accomplishments

NASA Astrophysics Data System (ADS)

Gross, R. S.

2017-12-01

The Global Geodetic Observing System (GGOS) of the International Association of Geodesy (IAG) provides the basis on which future advances in geosciences can be built. By considering the Earth system as a whole (including the geosphere, hydrosphere, cryosphere, atmosphere and biosphere), monitoring Earth system components and their interactions by geodetic techniques and studying them from the geodetic point of view, the geodetic community provides the global geosciences community with a powerful tool consisting mainly of high-quality services, standards and references, and theoretical and observational innovations. The mission of GGOS is: (a) to provide the observations needed to monitor, map and understand changes in the Earth's shape, rotation and mass distribution; (b) to provide the global frame of reference that is the fundamental backbone for measuring and consistently interpreting key global change processes and for many other scientific and societal applications; and (c) to benefit science and society by providing the foundation upon which advances in Earth and planetary system science and applications are built. The goals of GGOS are: (1) to be the primary source for all global geodetic information and expertise serving society and Earth system science; (2) to actively promote, sustain, improve, and evolve the integrated global geodetic infrastructure needed to meet Earth science and societal requirements; (3) to coordinate with the international geodetic services that are the main source of key parameters and products needed to realize a stable global frame of reference and to observe and study changes in the dynamic Earth system; (4) to communicate and advocate the benefits of GGOS to user communities, policy makers, funding organizations, and society. In order to accomplish its mission and goals, GGOS depends on the IAG Services, Commissions, and Inter-Commission Committees. The Services provide the infrastructure and products on which all contributions of GGOS are based. The IAG Commissions and Inter-Commission Committees provide expertise and support for the scientific development within GGOS. In summary, GGOS is IAG's central interface to the scientific community and to society in general. Recent activities and accomplishments of the Global Geodetic Observing System will be presented.

Space Geodetic Technique Co-location in Space: Simulation Results for the GRASP Mission

NASA Astrophysics Data System (ADS)

Kuzmicz-Cieslak, M.; Pavlis, E. C.

2011-12-01

The Global Geodetic Observing System-GGOS, places very stringent requirements in the accuracy and stability of future realizations of the International Terrestrial Reference Frame (ITRF): an origin definition at 1 mm or better at epoch and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale (0.1 ppb) and orientation components. These goals were derived from the requirements of Earth science problems that are currently the international community's highest priority. None of the geodetic positioning techniques can achieve this goal alone. This is due in part to the non-observability of certain attributes from a single technique. Another limitation is imposed from the extent and uniformity of the tracking network and the schedule of observational availability and number of suitable targets. The final limitation derives from the difficulty to "tie" the reference points of each technique at the same site, to an accuracy that will support the GGOS goals. The future GGOS network will address decisively the ground segment and to certain extent the space segment requirements. The JPL-proposed multi-technique mission GRASP (Geodetic Reference Antenna in Space) attempts to resolve the accurate tie between techniques, using their co-location in space, onboard a well-designed spacecraft equipped with GNSS receivers, a SLR retroreflector array, a VLBI beacon and a DORIS system. Using the anticipated system performance for all four techniques at the time the GGOS network is completed (ca 2020), we generated a number of simulated data sets for the development of a TRF. Our simulation studies examine the degree to which GRASP can improve the inter-technique "tie" issue compared to the classical approach, and the likely modus operandi for such a mission. The success of the examined scenarios is judged by the quality of the origin and scale definition of the resulting TRF.

GARS O'Higgins as a core station for geodesy in Antarctica

NASA Astrophysics Data System (ADS)

Klügel, Thomas; Diedrich, Erhard; Falk, Reinhard; Hessels, Uwe; Höppner, Kathrin; Kühmstedt, Elke; Metzig, Robert; Plötz, Christian; Reinhold, Andreas; Schüler, Torben; Wojdziak, Reiner

2014-05-01

The German Antarctic Receiving Station GARS O'Higgins at the northern tip of the Antarctic Peninsula is a dual purpose facility for Earth observation since more than 20 years. It serves as a satellite ground station for payload data downlink and telecommanding of remote sensing satellites as well as a geodetic observatory for global reference frames and global change. Both applications use the same 9m diameter radio telescope. For space geodesy and astrometry the radio telescope significantly improves the coverage on the southern hemisphere and plays an essential role within the global Very Long Baseline Interferometry (VLBI) network. In particular the determination of the Earth Orientation Parameters (EOP) and the sky coverage of the International Celectial Reference Frame (ICRF) benefit from the location at high southern latitude. Further geodetic instrumentation includes different permanent GNSS receivers (since 1995), two SAR corner reflectors (since 2013) and in the past a PRARE system (1996 - 2004). In addition absolute gravity measurements were performed in 1997 and 2011. All geodetic reference points are tied together by a local survey network. The various geodetic instrumentation and the long time series at O'Higgins allow a reliable determination of crustal motions. VLBI station velocities, continuous GNSS time series and absolute gravity measurements consistently document an uplift rate of about 5 mm/a. A pressure gauge and a radar tide gauge being refererenced to space by a GNSS antenna on top allow the measurement of sea level changes independently from crustal motions, and the determination of the ellipsoidal height of the sea surface, which is, the geoid height plus the mean dynamic topography. The outstanding location on the Antarctic continent makes GARS O'Higgins also in future attractive for polar orbiting satellite missions and an essential station for the global VLBI network. Future plans envisage a development towards an observatory for environmentally relevant research.

Mass intrusion beneath Kilauea Volcano, Hawaii, constraints from gravity and geodetic measurements (1975-2008)

NASA Astrophysics Data System (ADS)

Bagnardi, M.; Eggers, A.; Battaglia, M.; Poland, M.; Johnson, D.

2008-12-01

Since January 3 1983, Kilauea Volcano, Hawaii, has erupted almost continuously from vents on the volcano's east rift zone. On March 19, 2008, an explosion at Halema'uma'u Crater, within the summit caldera of Kilauea, marked the opening of a second eruptive vent on the volcano. The east rift vent at Pu'u'O'o and the summit vent at Halema'uma'u continue to be active as of August 2008, marking the longest interval in Kilauea's recorded history of eruptive activity on the volcano. Four gravity surveys with a network covering Kilauea's summit area have been performed during 1975-2003. We reoccupied this 45-station network in January and July 2008 with three portable LaCoste-Romberg gravimeters (G209, G615 and EG026) using a double-looping procedure. These two most recent gravity surveys span the onset of summit eruptive activity. The micro-gravity data set, combined with existing geodetic data from leveling, GPS, EDM, and InSAR, allow us to investigate and model the shallow magma system under the summit caldera to roughly constrain its shape, position, volume change and density, and better understand its long and short term evolution. We corrected for the effect of vertical deformation on gravity data (the so-called free-air effect) using uplift measurements from annual surveys performed by the USGS Hawaiian Volcano Observatory. Preliminary analysis of this record, which covers more than 30 years, indicates a persistent positive residual gravity anomaly located at the southeast margin of Halema'uma'u Crater, very close to the location of the new summit eruptive vent. This anomaly suggests a long term mass accumulation beneath the summit caldera.

INTEGRATION OF SHORT-TERM CO-SEISMIC DEFORMATION (InSAR) IN THE GEOMORPHIC DEVELOPMENT OF AN ACTIVELY UPLIFTING FOOTWALL, L’AQUILA EARTHQUAKE (06 APRIL, 2009), ITALY

NASA Astrophysics Data System (ADS)

Berti, C.; Pazzaglia, F. J.; Ramage, J. M.; Miccadei, E.; Piacentini, T.

2009-12-01

Central Italy is a well know region of frequent seismic activity focused along the topographic axis of the Apennines, with several, damaging > M. 5 events in the past decade. Conversely, the integrated effect of these earthquakes in shaping the long term development of the landscape is a poorly understood, but potentially powerful process in describing the region’s paleoseismicity and steadiness of hazardous earthquakes. The recent M. 6.3 L’Aquila earthquake of 06 April, 2009 ruptured a fault in a region of well-known geologic, geomorphic, and geodetic constraining data including hanging wall continental basin Quaternary deposits, footwall stream networks with distinct knickpoints, a dense GPS network, and InSAR interferometry. Collectively, the geodetic data describe the short-term, co- and immediately post-seismic behavior of the earthquake, whereas the geologic and geomorphic data record how discrete rupture events are encoded in the landscape and reflected in processes actively shaping the topography. Envisat and ALOS derived interferograms generated using ROI PAC show close spatial overlap of the InSAR-determined rupture and the Paganica fault, separating a deeply incised, uplifted carbonate footwall block and an actively subsiding Quaternary continental basin. Deposition in the continental basin has been unsteady and is commonly attributed to climate-modulated sediment flux from the uplifted footwall. We note however, that the longitudinal profiles of streams in the footwall are marked by distinct knickpoints that do not correspond to known or obvious lithologic or structural controls. Rather, the knickpoints are located a linear distance from the Paganica fault and at a topographic elevation consistent with detachment-limited stream-power erosional retreat processes instigated by instantaneous base level fall at the mountain front. Furthermore, the magnitude of river incision and elevation of the knickpoints scales with the co-seismic deformation pattern we measure through our InSAR approach. The time of the base level falls can be estimated assuming a model for knickpoint retreat rate and through correlation of knickpoints to lithostratigraphic packages of sediment in the continental basin. These results suggest that the Paganica fault has a characteristic rupture geometry, but an unsteady rupture behavior punctuated by periods of frequent activity interspersed with periods of quiescence that persist for several millennia. We conclude that the Paganica fault is currently in an active rupture phase. Regional geomorphic metrics suggest that as the Paganica fault passes through its current active phase, deformation should be transferred to the Campo Imperatore fault, which is currently in a relatively inactive, interseismic phase. Such a prediction is testable by geodetic techniques including InSAR to capture the slow, but cumulative interseismic component of active extension for this part of the Apennines.

Generation of Global Geodetic Networks for GGOS

NASA Astrophysics Data System (ADS)

MacMillan, Daniel; Pavlis, Erricos C.; Kuzmicz-Cieslak, Magda; Koenig, Daniel

2016-12-01

We simulated future networks of VLBI+SLR sites to assess their performance. The objective is to build a global network of geographically well distributed, co-located next-generation sites from each of the space geodetic techniques. The network is being designed to meet the GGOS terrestrial reference frame goals of 1 mm in accuracy and 0.1 mm/yr in stability. We simulated the next generation networks that should be available in five years and in ten years to assess the likelihood that these networks will meet the reference frame goals. Simulations were based on the expectation that 17 broadband VLBI stations will be available in five years and 27 stations in ten years. We also consider the improvement resulting from expanding the network by six additional VLBI sites to improve the global distribution of the network. In the simulations, the networks will operate continuously, but we account for station downtime for maintenance or because of bad weather. We ran SLR+VLBI combination TRF solutions, where site ties were used to connect the two networks in the same way as in combination solutions with observed data. The strengths of VLBI and SLR allows them to provide the necessary reference frame accuracy in scale, geocenter, and orientation. With the +10-year extended network operating for ten years, simulations indicate that scale, origin, and orientation accuracies will be at the level of 0.02 ppb, 0.2 mm, and 6 μas. Combining the +5-year and +10-year network realizations will provide better estimates of accuracy and estimates of stability.

Characters of Vertical Variability with Geodetic Satellites and Ground-based Continuous GPS in Taiwan

NASA Astrophysics Data System (ADS)

Yang, C.-C.; Wu, Y.-H.; Chao, B. F.; Yu, S.-B.

2009-04-01

Present-day GPS network have been extensively used to monitor crustal deformation due to various geodynamic mechanisms. Situated among the Pacific Ring of Fire on the suture zone of Eurasian and Philippine Sea Plates, the island of Taiwan with a dense continuous GPS network since ~1996 and now over 300 stations sees plenty of geophysical phenomena including particularly prominent crustal motions. We assessed daily solution of each station's coordinate time series, and made the routine corrections, such as orbital, EOP, atmospheric and tidal corrections, using GAMIT/GLOBK software (with ITRF05). We then employ the Quasi-Observation Combination Analysis (QOCA) package to obtain the variability and trend after removing occasional earthquake "disruptions". Preliminary results show strong seasonal variations. We then utilize the numerical method of Empirical Orthogonal Function (EOF) to analysis the geophysical signals from the continuous and dense GPS vertical crustal motion observations. We wish to be able to characterize both the seasonal and non-seasonal variability in the vertical crustal motion, in terms of the EOF modes in the spatial domain over Taiwan (plus a few offshore islets) with time evolution spanning the entire period of time. Corraborating with time-variable gravity data from the geodetic satellite mission GRACE, we can further obtain vertical components of both mass-induced loading with respect to the precipitation minus evaporation and the crustal motion caused by the active tectonic processes on Taiwan.

Geodetic Results from Mark 4 VLBI

NASA Technical Reports Server (NTRS)

MacMillan, Daniel; Petrov, Leonid; Ma, Chopo

2002-01-01

We present geodetic results of a series of 30 VLBI experiments recorded in Mark 4 mode at rates of 128 and 256 Mbps. The formal uncertainties of UT1, polar motion, and nutation offsets derived from these experiments are better than the corresponding uncertainties from NEOS-A experiments by a factor of 1.3-2. Baseline length repeatability for the series of 32 experiments over a period of one year is about 0.9 ppb. For comparison, NEOS-A length repeatability is about 1.4 ppb. We will discuss optimal use of Mark 4 in the design of future observing networks.

Observations of strain accumulation across the San Andreas fault near Palmdale, California, with a two-color geodimeter

USGS Publications Warehouse

Langbein, J.O.; Linker, M.F.; McGarr, A.; Slater, L.E.

1982-01-01

Two-color laser ranging measurements during a 15-month period over a geodetic network spanning the San Andreas fault near Palmdale, California, indicate that the crust expands and contracts aseismically in episodes as short as 2 weeks. Shear strain parallel to the fault has accumulated monotonically since November 1980, but at a variable rate. Improvements in measurement precision and temporal resolution over those of previous geodetic studies near Palmdale have resulted in the definition of a time history of crustal deformation that is much more complex than formerly realized. Copyright ?? 1982 AAAS.

The AuScope geodetic VLBI array

NASA Astrophysics Data System (ADS)

Lovell, J. E. J.; McCallum, J. N.; Reid, P. B.; McCulloch, P. M.; Baynes, B. E.; Dickey, J. M.; Shabala, S. S.; Watson, C. S.; Titov, O.; Ruddick, R.; Twilley, R.; Reynolds, C.; Tingay, S. J.; Shield, P.; Adada, R.; Ellingsen, S. P.; Morgan, J. S.; Bignall, H. E.

2013-06-01

The AuScope geodetic Very Long Baseline Interferometry array consists of three new 12-m radio telescopes and a correlation facility in Australia. The telescopes at Hobart (Tasmania), Katherine (Northern Territory) and Yarragadee (Western Australia) are co-located with other space geodetic techniques including Global Navigation Satellite Systems (GNSS) and gravity infrastructure, and in the case of Yarragadee, satellite laser ranging (SLR) and Doppler Orbitography and Radiopositioning Integrated by Satellite (DORIS) facilities. The correlation facility is based in Perth (Western Australia). This new facility will make significant contributions to improving the densification of the International Celestial Reference Frame in the Southern Hemisphere, and subsequently enhance the International Terrestrial Reference Frame through the ability to detect and mitigate systematic error. This, combined with the simultaneous densification of the GNSS network across Australia, will enable the improved measurement of intraplate deformation across the Australian tectonic plate. In this paper, we present a description of this new infrastructure and present some initial results, including telescope performance measurements and positions of the telescopes in the International Terrestrial Reference Frame. We show that this array is already capable of achieving centimetre precision over typical long-baselines and that network and reference source systematic effects must be further improved to reach the ambitious goals of VLBI2010.

Korea Geodetic VLBI Station, Sejong

NASA Technical Reports Server (NTRS)

Donghyun, Baek; Sangoh, Yi; Hongjong, Oh; Sangchul, Han

2013-01-01

The Sejong VLBI station officially joined the IVS as a new Network Station in 2012. This report summarizes the activities of the Sejong station during 2012. The following are the activities at the station: 1) VLBI test observations were carried out with the Tsukuba 34-m antenna of the GSI in Japan. As a result, the Sejong antenna needs to improve its efficiency, which is currently in progress, 2) A survey to connect the VLBI reference point to GNSS and ground marks was conducted, and 3) To see the indirect effects of RFI (Radio Frequency Interference) at this place, we checked the omni-direction (AZ 0? to 360?, EL fixed at 7?) for RFI influence.

The use of geospatial web services for exchanging utilities data

NASA Astrophysics Data System (ADS)

Kuczyńska, Joanna

2013-04-01

Geographic information technologies and related geo-information systems currently play an important role in the management of public administration in Poland. One of these tasks is to maintain and update Geodetic Evidence of Public Utilities (GESUT), part of the National Geodetic and Cartographic Resource, which contains an important for many institutions information of technical infrastructure. It requires an active exchange of data between the Geodesy and Cartography Documentation Centers and institutions, which administrate transmission lines. The administrator of public utilities, is legally obliged to provide information about utilities to GESUT. The aim of the research work was to develop a universal data exchange methodology, which can be implemented on a variety of hardware and software platforms. This methodology use Unified Modeling Language (UML), eXtensible Markup Language (XML), and Geography Markup Language (GML). The proposed methodology is based on the two different strategies: Model Driven Architecture (MDA) and Service Oriented Architecture (SOA). Used solutions are consistent with the INSPIRE Directive and ISO 19100 series standards for geographic information. On the basis of analysis of the input data structures, conceptual models were built for both databases. Models were written in the universal modeling language: UML. Combined model that defines a common data structure was also built. This model was transformed into developed for the exchange of geographic information GML standard. The structure of the document describing the data that may be exchanged is defined in the .xsd file. Network services were selected and implemented in the system designed for data exchange based on open source tools. Methodology was implemented and tested. Data in the agreed data structure and metadata were set up on the server. Data access was provided by geospatial network services: data searching possibilities by Catalog Service for the Web (CSW), data collection by Web Feature Service (WFS). WFS provides also operation for modification data, for example to update them by utility administrator. The proposed solution significantly increases the efficiency of data exchange and facilitates maintenance the National Geodetic and Cartographic Resource.

Metsahovi Radio Observatory - IVS Network Station

NASA Technical Reports Server (NTRS)

Uunila, Minttu; Zubko, Nataliya; Poutanen, Markku; Kallunki, Juha; Kallio, Ulla

2013-01-01

In 2012, Metsahovi Radio Observatory together with Finnish Geodetic Institute officially became an IVS Network Station. Eight IVS sessions were observed during the year. Two spacecraft tracking and one EVN X-band experiment were also performed. In 2012, the Metsahovi VLBI equipment was upgraded with a Digital Base Band Converter, a Mark 5B+, a FILA10G, and a FlexBuff.

Update on the activities of the GGOS Bureau of Networks and Observations

NASA Technical Reports Server (NTRS)

Pearlman, Michael R.; Pavlis, Erricos C.; Ma, Chopo; Noll, Carey; Thaller, Daniela; Richter, Bernd; Gross, Richard; Neilan, Ruth; Mueller, Juergen; Barzaghi, Ricardo;

Distributing french seismologic data through the RESIF green IT datacentre

NASA Astrophysics Data System (ADS)

Volcke, P.; Gueguen, P.; Pequegnat, C.; Le Tanou, J.; Enderle, G.; Berthoud, F.

2012-12-01

RESIF is a nationwide french project aimed at building an excellent quality system to observe and understand the inner earth. The ultimate goal is to create a network throughout mainland France comprising 750 seismometers and geodetic measurement instruments, 250 of which will be mobile to enable the observation network to be focused on specific investigation subjects and geographic locations. This project includes the implementation of a data distribution centre hosting seismologic and geodetic data. This datacentre is operated by the Université Joseph Fourier, Grenoble, France. In the context of building the necessary computing infrastructure, the Université Joseph Fourier became the first french university earning the status of "Participant" for the European Union "Code of Conduct for Data Centres". The University commits to energy reporting and implementing best practices for energy efficiency, in a cost effective manner, without hampering mission critical functions. In this context, data currently hosted at the RESIF datacentre include data from french broadband permanent network, strong motion permanent network, and mobile seismological network. These data are freely accessible as realtime streams and continuous validated data, along with instrumental metadata, delivered using widely known formats. Futur developments include tight integration with local super-computing ressources, and setting up modern distribution systems like webservices.

Establishment of Karadeniz Technical University Permanent GNSS Station as Reactivated of TRAB IGS Station

NASA Astrophysics Data System (ADS)

Kazancı, Selma Zengin; Kayıkçı, Emine Tanır

2017-12-01

In recent years, Global Navigation Satellite Systems (GNSS) have gained great importance in terms of the benefi ts it provides such as precise geodetic point positioning, determining crustal deformations, navigation, vehicle monitoring systems and meteorological applications etc. As in Turkey, for this purpose, each country has set up its own GNSS station networks like Turkish National Permanent RTK Network analyzed precise station coordinates and velocities together with the International GNSS Service, Turkish National Fundamental GPS Network and Turkish National Permanent GNSS Network (TNPGN) stations not only are utilized as precise positioning but also GNSS meteorology studies so total number of stations are increased. This work is related to the reactivated of the TRAB IGS station which was established in Karadeniz Technical University, Department of Geomatics Engineering. Within the COST ES1206 Action (GNSS4SWEC) KTU analysis center was established and Trop-NET system developed by Geodetic Observatory Pecny (GOP, RIGTC) in order to troposphere monitoring. The project titled "Using Regional GNSS Networks to Strengthen Severe Weather Prediction" was accepted to the scientifi c and technological research council of Turkey (TUBITAK). With this project, we will design 2 new constructed GNSS reference station network. Using observation data of network, we will compare water vapor distribution derived by GNSS Meteorology and GNSS Tomography. At this time, KTU AC was accepted as E-GVAP Analysis Centre in December 2016. KTU reference station is aimed to be a member of the EUREF network with these studies.

Vertical motions in Northern Victoria Land inferred from GPS: A comparison with a glacial isostatic adjustment model

USGS Publications Warehouse

Mancini, F.; Negusini, M.; Zanutta, A.; Capra, A.

2007-01-01

Following the densification of GPS permanent and episodic trackers in Antarctica, geodetic observations are playing an increasing role in geodynamics research and the study of the glacial isostatic adjustment (GIA). The improvement in geodetic measurements accuracy suggests their use in constraining GIA models. It is essential to have a deeper knowledge on the sensitivity of GPS data to motionsrelated to long-term ice mass changes and the present-day mass imbalance of the ice sheets. In order to investigate the geodynamic phenomena in Northern Victoria Land (NVL), GPS geodetic observations were made during the last decade within the VLNDEF (Victoria Land Network for Deformation control) project. The processed data provided a picture of the motions occurring in NVL with a high level of accuracy and depicts, for the whole period, a well defined pattern of vertical motion. The comparison between GPS-derived vertical displacementsand GIA is addressed, showing a good degree of agreement and highlighting the future use of geodetic GPS measurements as constraints in GIA models. In spite of this agreement, the sensitivity of GPS vertical rates to non-GIA vertical motions has to be carefully evaluated.

Height bias and scale effect induced by antenna gravitational deformations in geodetic VLBI data analysis

NASA Astrophysics Data System (ADS)

Sarti, Pierguido; Abbondanza, Claudio; Petrov, Leonid; Negusini, Monia

2011-01-01

The impact of signal path variations (SPVs) caused by antenna gravitational deformations on geodetic very long baseline interferometry (VLBI) results is evaluated for the first time. Elevation-dependent models of SPV for Medicina and Noto (Italy) telescopes were derived from a combination of terrestrial surveying methods to account for gravitational deformations. After applying these models in geodetic VLBI data analysis, estimates of the antenna reference point positions are shifted upward by 8.9 and 6.7 mm, respectively. The impact on other parameters is negligible. To simulate the impact of antenna gravitational deformations on the entire VLBI network, lacking measurements for other telescopes, we rescaled the SPV models of Medicina and Noto for other antennas according to their size. The effects of the simulations are changes in VLBI heights in the range [-3, 73] mm and a net scale increase of 0.3-0.8 ppb. The height bias is larger than random errors of VLBI position estimates, implying the possibility of significant scale distortions related to antenna gravitational deformations. This demonstrates the need to precisely measure gravitational deformations of other VLBI telescopes, to derive their precise SPV models and to apply them in routine geodetic data analysis.

Local Deformation Precursors of Large Earthquakes Derived from GNSS Observation Data

NASA Astrophysics Data System (ADS)

Kaftan, Vladimir; Melnikov, Andrey

2017-12-01

Research on deformation precursors of earthquakes was of immediate interest from the middle to the end of the previous century. The repeated conventional geodetic measurements, such as precise levelling and linear-angular networks, were used for the study. Many examples of studies referenced to strong seismic events using conventional geodetic techniques are presented in [T. Rikitake, 1976]. One of the first case studies of geodetic earthquake precursors was done by Yu.A. Meshcheryakov [1968]. Rare repetitions, insufficient densities and locations of control geodetic networks made difficult predicting future places and times of earthquakes occurrences. Intensive development of Global Navigation Satellite Systems (GNSS) during the recent decades makes research more effective. The results of GNSS observations in areas of three large earthquakes (Napa M6.1, USA, 2014; El Mayor Cucapah M7.2, USA, 2010; and Parkfield M6.0, USA, 2004) are treated and presented in the paper. The characteristics of land surface deformation before, during, and after earthquakes have been obtained. The results prove the presence of anomalous deformations near their epicentres. The temporal character of dilatation and shear strain changes show existence of spatial heterogeneity of deformation of the Earth’s surface from months to years before the main shock close to it and at some distance from it. The revealed heterogeneities can be considered as deformation precursors of strong earthquakes. According to historical data and proper research values of critical deformations which are offered to be used for seismic danger scale creation based on continuous GNSS observations are received in a reference to the mentioned large earthquakes. It is shown that the approach has restrictions owing to uncertainty of the moment in the beginning of deformation accumulation and the place of expectation of another seismic event. Verification and clarification of the derived conclusions are proposed.

New Geodetic Results from the Hauraki Rift: Slow Continental Rifting Oblique to Subduction, North Island, New Zealand

NASA Astrophysics Data System (ADS)

Pickle, R. C.; Eccles, J. D.; Hreinsdottir, S.; Palmer, N.; Rowland, J. V.

2016-12-01

The Hauraki Rift, an active but slow-deforming narrow intra-continental rift in northern New Zealand paradoxically strikes nearly normal to the Pacific-Australian oblique subduction boundary 300+ km to the southeast. Both the driving mechanism and quantitative details of the rift's current activity are unknown. Past GPS/GNSS geodetic surveying in the area has been coarse and erratic (e.g. single 8-hour surveys in 1995). In 2015 and again in 2016 a 37 station network of existing benchmarks around the rift was measured with the aim of gaining better insight into deformation in the region. We find that it is primarily extensional ( 0.9 mm/yr) with a small portion of right-lateral shearing ( 0.1 mm/yr) relative to a fixed Australian plate in ITRF2008. Closer to the plate boundary, the oblique westward subduction of the Pacific plate generates a strong clockwise angular strain signature in the over-riding plate; this same angular stress field is the simplest explanation for the Hauraki Rift's axis-perpendicular strain and in consistent with previous geophysical observations. Additionally, several short wavelength dislocations between our velocity solutions hint at the existence of undocumented active faults which will have implications to the seismic hazard to Auckland, New Zealand's largest city, located just 50km west of the rift.

Tilt networks of Mount Shasta and Lassen Peak, California

USGS Publications Warehouse

Dzurisin, Daniel; Johnson, Daniel J.; Murray, T.L.; Myers, Barbara

1982-01-01

In response to recent eruptions at Mount St. Helens and with support from the USGS Volcanic Hazards Program, the Cascades Volcano Observatory (CVO) has initiated a program to monitor all potentially-active volcanoes of the Cascade Range. As part of that effort, we installed tilt networks and obtained baseline measurements at Mount Shasta and Lassen Peak, California during July 1981. At the same time, baseline electronic distance measurements (EDM) were made and fumarole surveys were conducted by other crews from CVO. Annual surveys are planned initially, with subsequent visits as conditions warrant. These geodetic and geochemical measurements supplement a program of continuous seismic monitoring of Cascade volcanoes by the USGS Office of Earthquake Studies in cooperation with local universities. Other tilt networks were established at Mount Baker in 1975 and at Mount St. Helens in 1981. EDM networks were established at Mount Baker in 1975, Mount St. Helens in 1980, and Crater Lake in 1981. Additional tilt and/or EDM networks are planned for Mount Rainier, Mount Hood, Glacier Peak, Three Sisters, and Crater Lake as funds permit.

The Contribution of the Geodetic Community (WG4) to EPOS

NASA Astrophysics Data System (ADS)

Fernandes, R. M. S.; Bastos, L. C.; Bruyninx, C.; D'Agostino, N.; Dousa, J.; Ganas, A.; Lidberg, M.; Nocquet, J.-M.

2012-04-01

WG4 - "EPOS Geodetic Data and Infrastructure" is the Working Group of the EPOS project responsible to define and prepare the integration of the existing Pan-European Geodetic Infrastructures into a unique future consistent infrastructure that supports the European Geosciences, which is the ultimate goal of the EPOS project. The WG4 is formed by representatives of the participating EPOS countries and from EUREF (European Reference Frame), which also ensures the inclusion and the contact with countries that formally are not part of the current phase of EPOS. In reality, the fact that Europe is formed by many countries (having different laws and policies) lacking an infrastructure similar to UNAVCO (which concentrates the effort of the local geo-science community) raises the difficulties to create a common geodetic infrastructure serving not only the entire geo-science community, but also many other areas of great social-economic impact. The benefits of the creation of such infrastructure (shared and easily accessed by all) are evident in order to optimize the existing and future geodetic resources. This presentation intends to detail the work being produced within the working group WG4 related with the definition of strategies towards the implementation of the best solutions that will permit to the end-users, and in particular geo-scientists, to access the geodetic data, derived solutions, and associated metadata using transparent and uniform processes. Discussed issues include the access to high-rate data in near real-time, storage and backup of historical and future data, the sustainability of the networks in order to achieve long-term stability in the observation infrastructure, seamless access to the data, open data policies, and processing tools.

Integrating space geodesy and coastal sea level observations

NASA Astrophysics Data System (ADS)

Löfgren, J. S.; Haas, R.; Larson, K.; Scherneck, H.-G.

2012-04-01

The goal of the Global Geodetic Observing System (GGOS) is to monitor the Earth system, in particular with observations of the three fundamental geodetic observables: the Earth's shape, the Earth's gravity field and the Earth's rotational motion. A central part of GGOS is the network of globally distributed fundamental geodetic stations that allow the combination and integration of the different space geodetic techniques. One of these stations is the Onsala Space Observatory (OSO), on the west coast of Sweden, which operates equipment for geodetic Very Long Baseline Interferometry, Global Navigation Satellite System (GNSS), and superconducting gravimetry measurements, and additionally water vapour radiometers. The newest addition to the OSO fundamental geodetic station is a GNSS-based tide gauge (GNSS-TG). This installation integrates space geodesy with remote sensing of the local sea level. The GNSS-TG uses both direct GNSS-signals and GNSS-signals that are reflected off the sea surface. This is done using a zenith-looking Right Hand Circular Polarized (RHCP) and a nadir-looking Left Hand Circular Polarized (LHCP) antenna, respectively. Each of the two antennas is connected to a standard geodetic-type GNSS-receiver. The analysis of the data received with the RHCP-antenna allows one to determine land motion, while the analysis of the data received with the LHCP-antenna allows one to determine the sea surface height. Analysing both data sets together results in local sea level that is automatically corrected for land motion, meaning that the GNSS-TG can provide reliable sea-level estimates even in tectonically active regions. Previous results from the GNSS-TG, using carrier phase data, show a Root-Mean-Square (RMS) agreement of less than 5.9 cm with stilling well gauges located 18 km and 33 km away from OSO (Löfgren et al., 2011). This is lower than the RMS agreement between the two stilling well gauges (6.1 cm). Furthermore, significant ocean tidal signals have been derived from a several months long time series. Additionally, preliminary results from analysis of the Signal-to-Noise Ratio (SNR) from the RHCP antenna show an RMS agreement of 4.5 cm with a linear combination of the previously mentioned stilling well gauges (Larson et al., 2011). We present new sea level results from the GNSS-TG data set, assessing several different analysis strategies. For example, we investigate optimal ways to analyse the carrier phase data (using observations from both antennas) and compare the results to those derived from the SNR analysis (using observations from the RHCP antenna only). Furthermore, the processing results are compared to independently derived sea level observations from co-located pressure sensor gauges.

Global satellite triangulation and trilateration for the National Geodetic Satellite Program (solutions WN 12, 14 and 16). [study and analysis of data from artificial satellites

NASA Technical Reports Server (NTRS)

Mueller, I. I.; Kumar, M.; Reilly, J. P.; Saxena, N.; Soler, T.

1973-01-01

A multi-year study and analysis of data from satellites launched specifically for geodetic purposes and from other satellites useful in geodetic studies was conducted. The program of work included theoretical studies and analysis for the geometric determination of station positions derived from photographic observations of both passive and active satellites and from range observations. The current status of data analysis, processing and results are examined.

Satellite time synchronization of a NASA network.

NASA Technical Reports Server (NTRS)

Laios, S. C.

1972-01-01

A satellite time synchronization technique has been used for synchronization of remotely separated clocks during the past several years. The NASA network has been successfully synchronized to an accuracy of tens of microseconds via the NASA Geodetic Earth Orbiting Satellite GEOS-11. The results indicate that a polar orbit satellite having an onboard clock can effectively be used to synchronize clocks on a global basis.

Upgrading the seismic and geodetic network of the Popocatépetl volcano (Mexico).

NASA Astrophysics Data System (ADS)

Calò, Marco; Iglesias Mendoza, Arturo; Legrand, Denis; Valdés González, Carlos Miguel; Perez Campos, Xyoli

2017-04-01

The Popocatépetl is one of the most active volcanoes in Mexico and is located only 70 km from Mexico City, populated by more than 20 millions of people, and only 35 km from the Puebla municipality with almost 1.5 millions of people living. The recent activity of the volcano is generally marked by explosions emitting ash plumes often reaching the densely populated regions. In the framework of the Mexican Fund for Prevention of Natural Disasters (FOPREDEN) we are renovating and upgrading the existing geodetic and seismic networks monitoring the volcano. In this project we are installing 10 broadband seismic stations (120s-050Hz) in shallow boreholes (3-5m depth) and 4 GPS with real time sampling rate of 1 Hz. All instruments are equipped with continuous recording systems for real time monitoring purposes and research. The Popocatépetl exceeds 5400m, and the altitude of the stations ranges from 2200 m to 4300 m making it difficult their installation and maintenance. Because of ash emissions and the hard working condition, the real-time transmission is split into two systems in order to ensure the monitoring of the volcano also during the highest expected activity. Therefore we set up a network of "first order", consisting of four stations located about 20 km from the crater and equipped with satellite transmission. These stations, being far enough from the crater, ensure the real time monitoring of the major events also during intense periods of activity of the volcano. The remaining six stations are installed near to the crater (less than 10 km) and take part of the "second order" network equipped with a telemetered radio system transmitting the data either directly to the National Center of Disaster Prevention (CENAPRED) and National Seismological Service (SSN) or to the first order stations (for the sites that have not direct visible line with the monitoring centers). The four GPS sensors are all installed in the second order sites in order to monitor the largest deformations at the top of the volcano. In this work we show both the installation procedure of the boreholes seismometers in hard conditions and their improved performance with respect to the actual stations installed at surface and the scheme of the transmitting system for ensuring the monitoring of the Popocatépetl volcano in all the possible scenarios of its activity.

IVS Organization

NASA Technical Reports Server (NTRS)

2004-01-01

International VLBI Service (IVS) is an international collaboration of organizations which operate or support Very Long Baseline Interferometry (VLBI) components. The goals are: To provide a service to support geodetic, geophysical and astrometric research and operational activities. To promote research and development activities in all aspects of the geodetic and astrometric VLBI technique. To interact with the community of users of VLBI products and to integrate VLBI into a global Earth observing system.

Subsidence at the Fairport Harbor Water Level Gauge

NASA Astrophysics Data System (ADS)

Conner, D. A.

2014-12-01

SUBSIDENCE AT THE FAIRPORT HARBOR WATER LEVEL GAUGE I will provide information on methods being used to monitor Lake Erie water levels and earth movement at Fairport Harbor, Ohio. Glacial Isostatic Adjustment (GIA) is responsible for vertical movement throughout the Great Lakes region. Fairport Harbor is also experiencing vertical movement due to salt mining, so the nearby water level gauge operated by the National Oceanic and Atmospheric Administration (NOAA) is affected by both GIA and mining. NOAA's National Geodetic Survey (NGS) defines and maintains the National Spatial Reference System (NSRS). The NSRS includes a network of permanently marked points; a consistent, accurate, and up-to-date national shoreline; a network of Continuously Operating Reference Stations (CORS) which supports three-dimensional positioning activities; and a set of accurate models describing dynamic, geophysical processes that affect spatial measurements. The NSRS provides the spatial reference foundation for transportation, mapping, charting and a multitude of scientific and engineering applications. Fundamental elements of geodetic infrastructure include GPS CORS (3-D), water level and tide gauges (height) and a system of vertical bench marks (height). When two or more of these elements converge they may provide an independent determination of position and vertical stability as is the case here at the Fairport Harbor water level gauge. Analysis of GPS, leveling and water level data reveal that this gauge is subsiding at about 2-3 mm/year, independent of the effects of GIA. Analysis of data from the nearby OHLA GPS CORS shows it subsiding at about 4 mm/yr, four times faster than expected due to GIA alone. A long history of salt mine activity in the area is known to geologists but it came as a surprise to other scientists.

Current Limitations on VLBI Accuracy

NASA Technical Reports Server (NTRS)

Ma, Chopo; Gipson, John; MacMillan, Daniel

1998-01-01

The contribution of VLBI to geophysics and geodesy arises from its ability to measure distances between stations in a network and to determine the orientation of stations in the network as well as the orientation of the network with respect to the external reference frame of extragalactic radio objects. Integrating nearly two decades of observations provides useful information about station positions and velocities and the orientation of the Earth, but the complications of the real world and the limitations of observing, modeling and analysis prevent recovery of all effects. Of the factors that limit the accuracy of seemingly straightforward geodetic parameters, the neutral propagation medium has been subject to the greatest scrutiny, but the treatment of the mapping function, the wet component and spatial/temporal inhomogeneities is still improving. These affect both the terrestrial scale and consistency over time. The modeling of non-secular site motions (tides and loading) has increased in sophistication, but there are some differences between the models and the observations. VLBI antennas are massive objects, so their behavior is quite unlike GPS monuments, but antenna deformations add some (generally) unmodeled signal. Radio sources used in geodetic VLBI observations are selected for strength and (relative) absence of structure, but apparent changes in position can leak into geodetic parameters. A linear rate of change of baseline or site parameters is the simplest model and its error improves with time span. However, in most cases the VLBI data distribution is insufficient to look for real non-linear behavior that might affect the average rate. A few sites have multiple VLBI antennas, and some show small differences in rate. VLBI intrinsically measures relative positions and velocities, but individual site positions and velocities are generally more useful. The creation of the VLBI terrestrial reference frame, which transforms relative information into individual results, is an empirical process that has intrinsic errors. While UT1 is uniquely measured by VLBI, the geographical distribution and availability of VLBI stations, especially in the southern hemisphere, and the consistency of the VLBI terrestrial reference frame may limit the accuracy of Earth orientation measurements. The effects of particular error sources on geodetic and geophysical parameters derived from VLBI data will be illustrated.

Observing APOD with the AuScope VLBI Array

PubMed Central

Sun, Jing; Cao, Jianfeng

2018-01-01

The possibility to observe satellites with the geodetic Very Long Baseline Interferometry (VLBI) technique is vividly discussed in the geodetic community, particularly with regard to future co-location satellite missions. The Chinese APOD-A nano satellite can be considered as a first prototype—suitable for practical observation tests—combining the techniques Satellite Laser Ranging (SLR), Global Navigation Satellite Systems (GNSS) and VLBI on a single platform in a Low Earth Orbit (LEO). Unfortunately, it has hardly been observed by VLBI, so major studies towards actual frame ties could not be performed. The main reason for the lack of observations was that VLBI observations of satellites are non-standard, and suitable observing strategies were not in place for this mission. This work now presents the first serious attempt to observe the satellite with a VLBI network over multiple passes. We introduce a series of experiments with the AuScope geodetic VLBI array which were carried out in November 2016, and describe all steps integrated in the established process chain: the experiment design and observation planning, the antenna tracking and control scheme, correlation and derivation of baseline-delays, and the data analysis yielding delay residuals on the level of 10 ns. The developed procedure chain can now serve as reference for future experiments, hopefully enabling the global VLBI network to be prepared for the next co-location satellite mission. PMID:29772732

Observing APOD with the AuScope VLBI Array.

PubMed

Hellerschmied, Andreas; McCallum, Lucia; McCallum, Jamie; Sun, Jing; Böhm, Johannes; Cao, Jianfeng

2018-05-16

The possibility to observe satellites with the geodetic Very Long Baseline Interferometry (VLBI) technique is vividly discussed in the geodetic community, particularly with regard to future co-location satellite missions. The Chinese APOD-A nano satellite can be considered as a first prototype-suitable for practical observation tests-combining the techniques Satellite Laser Ranging (SLR), Global Navigation Satellite Systems (GNSS) and VLBI on a single platform in a Low Earth Orbit (LEO). Unfortunately, it has hardly been observed by VLBI, so major studies towards actual frame ties could not be performed. The main reason for the lack of observations was that VLBI observations of satellites are non-standard, and suitable observing strategies were not in place for this mission. This work now presents the first serious attempt to observe the satellite with a VLBI network over multiple passes. We introduce a series of experiments with the AuScope geodetic VLBI array which were carried out in November 2016, and describe all steps integrated in the established process chain: the experiment design and observation planning, the antenna tracking and control scheme, correlation and derivation of baseline-delays, and the data analysis yielding delay residuals on the level of 10 ns. The developed procedure chain can now serve as reference for future experiments, hopefully enabling the global VLBI network to be prepared for the next co-location satellite mission.

Instituto Geografico Nacional of Spain

NASA Technical Reports Server (NTRS)

Colomer, Francisco; Garcia-Espada, Susana; Gomez-Gonzalez, Jesus; Lopez-Fernandez, Jose Antonio; Santamaria-Gomez, Alvaro; De Vicente, Pablo

2013-01-01

This report updates the description of the space geodesy facilities of the Spanish National Geographic Institute (IGN). The current 40-meter radio telescope at Yebes, a network station for IVS, has performed geodetic VLBI observations regularly since September 2008. In addition to this, the project to establish an Atlantic Network of Geodynamical and Space Stations (RAEGE) is progressing with the construction of the first antenna, which is being erected at Yebes.

Automated and dynamic scheduling for geodetic VLBI - A simulation study for AuScope and global networks

NASA Astrophysics Data System (ADS)

Iles, E. J.; McCallum, L.; Lovell, J. E. J.; McCallum, J. N.

2018-02-01

As we move into the next era of geodetic VLBI, the scheduling process is one focus for improvement in terms of increased flexibility and the ability to react with changing conditions. A range of simulations were conducted to ascertain the impact of scheduling on geodetic results such as Earth Orientation Parameters (EOPs) and station coordinates. The potential capabilities of new automated scheduling modes were also simulated, using the so-called 'dynamic scheduling' technique. The primary aim was to improve efficiency for both cost and time without losing geodetic precision, particularly to maximise the uses of the Australian AuScope VLBI array. We show that short breaks in observation will not significantly degrade the results of a typical 24 h experiment, whereas simply shortening observing time degrades precision exponentially. We also confirm the new automated, dynamic scheduling mode is capable of producing the same standard of result as a traditional schedule, with close to real-time flexibility. Further, it is possible to use the dynamic scheduler to augment the 3 station Australian AuScope array and thereby attain EOPs of the current global precision with only intermittent contribution from 2 additional stations. We thus confirm automated, dynamic scheduling bears great potential for flexibility and automation in line with aims for future continuous VLBI operations.

A Comparative Study of the Applied Methods for Estimating Deflection of the Vertical in Terrestrial Geodetic Measurements

PubMed Central

Vittuari, Luca; Tini, Maria Alessandra; Sarti, Pierguido; Serantoni, Eugenio; Borghi, Alessandra; Negusini, Monia; Guillaume, Sébastien

2016-01-01

This paper compares three different methods capable of estimating the deflection of the vertical (DoV): one is based on the joint use of high precision spirit leveling and Global Navigation Satellite Systems (GNSS), a second uses astro-geodetic measurements and the third gravimetric geoid models. The working data sets refer to the geodetic International Terrestrial Reference Frame (ITRF) co-location sites of Medicina (Northern, Italy) and Noto (Sicily), these latter being excellent test beds for our investigations. The measurements were planned and realized to estimate the DoV with a level of precision comparable to the angular accuracy achievable in high precision network measured by modern high-end total stations. The three methods are in excellent agreement, with an operational supremacy of the astro-geodetic method, being faster and more precise than the others. The method that combines leveling and GNSS has slightly larger standard deviations; although well within the 1 arcsec level, which was assumed as threshold. Finally, the geoid model based method, whose 2.5 arcsec standard deviations exceed this threshold, is also statistically consistent with the others and should be used to determine the DoV components where local ad hoc measurements are lacking. PMID:27104544

Integration of space geodesy: A US National Geodetic Observatory

NASA Astrophysics Data System (ADS)

Yunck, Thomas P.; Neilan, Ruth E.

2005-11-01

In the interest of improving the performance and efficiency of space geodesy a diverse group in the US, in collaboration with IGGOS, has begun to establish a unified National Geodetic Observatory (NGO). To launch this effort an international team will conduct a multi-year program of research into the technical issues of integrating SLR, VLBI, and GPS geodesy to produce a unified set of global geodetic products. The goal is to improve measurement accuracy by up to an order of magnitude while lowering the cost to current sponsors. A secondary goal is to expand and diversify international sponsorship of space geodesy. Principal benefits will be to open new vistas of research in geodynamics and surface change while freeing scarce NASA funds for scientific studies. NGO will proceed in partnership with, and under the auspices of, the International Association of Geodesy (IAG) as an element of the Integrated Global Geodetic Observation System project. The collaboration will be conducted within, and will make full use of, the IAG's existing international services: the IGS, IVS, ILRS, and IERS. Seed funding for organizational activities and technical analysis will come from NASA's Solid Earth and Natural Hazards Program. Additional funds to develop an integrated geodetic data system known as Inter-service Data Integration for Geodetic Operations (INDIGO), will come from a separate NASA program in Earth science information technology. INDIGO will offer ready access to the full variety of NASA's space geodetic data and will extend the GPS Seamless Archive (GSAC) philosophy to all space geodetic data types.

Feasibility of Construction of the Continuously Operating Geodetic GPS Network of Sinaloa, Mexico

NASA Astrophysics Data System (ADS)

Vazquez, G. E.; Jacobo, C.

2011-12-01

This research is based on the study and analysis of feasibility for the construction of the geodetic network for GPS continuous operation for Sinaloa, hereafter called (RGOCSIN). A GPS network of continuous operation is defined as that materialized structure physically through permanent monuments where measurements to the systems of Global Positioning (GPS) is performed continuously throughout a region. The GPS measurements in this network are measurements of accuracy according to international standards to define its coordinates, thus constituting the basic structure of geodetic referencing for a country. In this context is that in the near future the RGOCSIN constitutes a system state only accurate and reliable georeferencing in real-time (continuous and permanent operation) and will be used for different purposes; i.e., in addition to being fundamental basis for any lifting topographic or geodetic survey, and other areas such as: (1) Different construction processes (control and monitoring of engineering works); (2) Studies of deformation of the Earth's crust (before and after a seismic event); (3) GPS meteorology (weather forecasting); (4) Demarcation projects (natural and political); (5) Establishment of bases to generate mapping (necessary for the economic and social development of the state); (6) Precision agriculture (optimization of economic resources to the various crops); (7) Geographic information systems (Organization and planning activities associated with the design and construction of public services); (8) Urban growth (possible settlements in the appropriate form and taking care of the environmental aspect), among others. However there are criteria and regulations according to the INEGI (Instituto Nacional de Estadística y Geografía, http://www.inegi.org.mx/) that must be met; even for this stage of feasibility of construction that sees this project as a first phase. The fundamental criterion to be taken into account according to INEGI is a geometric distribution appropriate to ensure the state coverage, so the radius of coverage is found in the 10 to 15 Km. station. Likewise INEGI recommends the implementation of GPS measurements a priori in the vertices where at the end of such measurements generate a report by station containing details of the conditions of visibility, the GPS equipment used, the methodology of measurement and field data processing mode and is intended to build the RGOCSIN. Based on the results of the final report for each one of the measures beforehand, it will be or not feasible to determine if it meets these specifications to be finally considered as part of the RGOCSIN. It should be noted that the selection of the potential places where is intended to carry out the study and analysis of feasibility for the construction of the RGOCSIN will be some of the weather stations of the Centro de Investigación en Alimentación y Desarrollo (CIAD) Culiacán (http://www.ciad.edu.mx/clima/pc.asp). These weather stations have some technical infrastructure which would be used in the future; In addition to providing meteorological information which will ensure success in the solution of scientific and technological problems in various sectors requiring our state.

Gravity measurements in southeastern Alaska reveal negative gravity rate of change caused by glacial isostatic adjustment

NASA Astrophysics Data System (ADS)

Sun, W.; Miura, S.; Sato, T.; Sugano, T.; Freymueller, J.; Kaufman, M.; Larsen, C. F.; Cross, R.; Inazu, D.

2010-12-01

For the past 300 years, southeastern Alaska has undergone rapid ice-melting and land uplift attributable to global warming. Corresponding crustal deformation (3 cm/yr) caused by the Little Ice Age retreat is detectable with modern geodetic techniques such as GPS and tidal gauge measurements. Geodetic deformation provides useful information for assessing ice-melting rates, global warming effects, and subcrustal viscosity. Nevertheless, integrated geodetic observations, including gravity measurements, are important. To detect crustal deformation caused by glacial isostatic adjustment and to elucidate the viscosity structure in southeastern Alaska, Japanese and U.S. researchers began a joint 3-year project in 2006 using GPS, Earth tide, and absolute gravity measurements. A new absolute gravity network was established, comprising five sites around Glacier Bay, near Juneau, Alaska. This paper reports the network's gravity measurements during 2006-2008. The bad ocean model in this area hindered ocean loading correction: Large tidal residuals remain in the observations. Accurate tidal correction necessitated on-site tidal observation. Results show high observation precision for all five stations: <1 μGal. The gravity rate of change was found to be -3.5 to -5.6 μGal/yr in the gravity network. Furthermore, gravity results obtained during the 3 years indicate a similar gravity change rate. These gravity data are anticipated for application in geophysical studies of southeastern Alaska. Using gravity and vertical displacement data, we constructed a quantity to remove viscoelastic effects. The observations are thus useful to constrain present-day ice thickness changes. A gravity bias of about -13.2 ± 0.1 mGal exists between the Potsdam and current FG5 gravity data.

Multidisciplinary Observations of Subduction (MOOS) Experiment in South-Central Alaska

NASA Astrophysics Data System (ADS)

Christensen, D.; Abers, G.; Freymueller, J.

2008-12-01

Seismic and geodetic data are being collected in the Kenai Peninsula and surrounding area of south central Alaska as part of the PASSCAL experiment MOOS. A total of 34 broadband seismic stations were deployed between the summers of 2007 and 2008. Seventeen of these stations continue to operate for an additional year and are scheduled to be removed in the summer of 2009. Numerous GPS campaign sites have and will be visited during the same time period. The MOOS seismic deployment provides coverage across the interplate coupled zone and adjacent transition zone in the shallow parts of the Alaskan subduction zone. It is a southern extension of an earlier broadband deployment BEAAR (Broadband Experiment Across the Alaska Range) to the north. When integrated with the previous BEAAR experiment, these data will allow high-resolution broadband imaging along a 600 km long transect over the Alaska subduction zone, at 10-15 km station spacing. The MOOS deployment allows us to test several hypotheses relating to the postulated subduction of the Yakutat Block and the nature of the coupled zone which ruptured in the great 1964 earthquake. The seismic and geodetic stations cover an area that includes part of the 1964 main asperity and the adjacent, less coupled, region to the southwest. Data gathered from this experiment will shed light on the nature of this boundary from both a geodetic and seismic (or earth structure) perspective. Shallow seismicity recorded by this network greatly improves the catalog of events in this area and helps to delineate active features in the subduction complex. Preliminary results from this project will be presented.

NASA's Contribution to Global Space Geodesy Networks

NASA Technical Reports Server (NTRS)

Bosworth, John M.

1999-01-01

The NASA Space Geodesy program continues to be a major provider of space geodetic data for the international earth science community. NASA operates high performance Satellite Laser Ranging (SLR), Very Long Baseline Interferometry (VLBI) and Global Positioning System (GPS) ground receivers at well over 30 locations around the world and works in close cooperation with space geodetic observatories around the world. NASA has also always been at the forefront in the quest for technical improvement and innovation in the space geodesy technologies to make them even more productive, accurate and economical. This presentation will highlight the current status of NASA's networks; the plans for partnerships with international groups in the southern hemisphere to improve the geographic distribution of space geodesy sites and the status of the technological improvements in SLR and VLBI that will support the new scientific thrusts proposed by interdisciplinary earth scientists. In addition, the expanding role of the NASA Space geodesy data archive, the CDDIS will be described.

Tracking strategies for laser ranging to multiple satellite targets

NASA Technical Reports Server (NTRS)

Robbins, J. W.; Smith, D. E.; Kolenkiewicz, R.

1994-01-01

By the middle of the decade, several new Laser Geodynamic Satellites will be launched to join the current constellation comprised of the laser geodynamic satellite (LAGEOS) (US), Starlette (France), Ajisai (Japan), and Etalon I and II (USSR). The satellites to be launched, LAGEOS II and III (US & Italy), and Stella (France), will be injected into orbits that differ from the existing constellation so that geodetic and gravimetric quantities are sampled to enhance their resolution and accuracy. An examination of various possible tracking strategies adopted by the network of laser tracking stations has revealed that the recovery of precise geodetic parameters can be obtained over shorter intervals than is currently obtainable with the present constellation of satellites. This is particularly important in the planning of mobile laser tracking operations, given a network of permanently operating tracking sites. Through simulations, it is shown that laser tracking of certain satellite passes, pre-selected to provide optimal sky-coverage, provides the means to acquire a sufficient amount of data to allow the recovery of 1 cm station positions.

Study of the active deformation of Mitidja (Tell Atlas, Algeria) by GPS

NASA Astrophysics Data System (ADS)

Bacha, Wahab; Masson, Frederic; Yelles-Chaouche, Abdelkrim; Lammali, Kamel; Bellik, Amar; Hamai, Lamine

2013-04-01

A network was created in the Mitidja region around the capital Algiers (Algeria). It has been established to study the deformation of the region and the slow operation of flaws in it. The network was installed by a distribution of GPS stations according to structural domains existing in the region. Twelve bases spread across the study area, have been installed. The measurements were acquired by performing four measurement campaigns in 2006, 2007, 2009 and 2010, with sessions over a month of action. This work allowed the installation of a geodetic network of regional monitoring by methodology GPS in the zone of Mitidja (Tellian Atlas, Algeria). Four observation campaigns were carried out on this area with session's superiors in one month of measurements. The treatment was carried out with software GAMIT-GLOBK, the network is attached to several world stations IGS treated between 2000-2010, indexed in a precise frame of reference ITRF05. The results presented in this memory show a deformation in shortening ≤ 0.5 mm/an in the plain of Mitidja and the surrounding Solid masses.

International VLBI Service for Geodesy and Astrometry 2014 Annual Report

NASA Technical Reports Server (NTRS)

Baver, Karen D. (Editor); Behrend, Dirk (Editor); Armstrong, Kyla L. (Editor)

2015-01-01

IVS is an international collaboration of organizations which operate or support Very Long Baseline Interferometry (VLBI) components. The goals are: 1. To provide a service to support geodetic, geophysical and astrometric research and operational activities. 2. To promote research and development activities in all aspects of the geodetic and astrometric VLBI technique. 3. To interact with the community of users of VLBI products and to integrate VLBI into a global Earth observing system.

Brief communication: Co-seismic displacement on 26 and 30 October 2016 (Mw = 5.9 and 6.5) - earthquakes in central Italy from the analysis of a local GNSS network

NASA Astrophysics Data System (ADS)

De Guidi, Giorgio; Vecchio, Alessia; Brighenti, Fabio; Caputo, Riccardo; Carnemolla, Francesco; Di Pietro, Adriano; Lupo, Marco; Maggini, Massimiliano; Marchese, Salvatore; Messina, Danilo; Monaco, Carmelo; Naso, Salvatore

2017-11-01

On 24 August 2016 a strong earthquake (Mw = 6.0) affected central Italy and an intense seismic sequence started. Field observations, DInSAR (Differential INterferometry Synthetic-Aperture Radar) analyses and preliminary focal mechanisms, as well as the distribution of aftershocks, suggested the reactivation of the northern sector of the Laga fault, the southern part of which was already rebooted during the 2009 L'Aquila sequence, and of the southern segment of the Mt Vettore fault system (MVFS). Based on this preliminary information and following the stress-triggering concept (Stein, 1999; Steacy et al., 2005), we tentatively identified a potential fault zone that is very vulnerable to future seismic events just north of the earlier epicentral area. Accordingly, we planned a local geodetic network consisting of five new GNSS (Global Navigation Satellite System) stations located a few kilometres away from both sides of the MVFS. This network was devoted to working out, at least partially but in some detail, the possible northward propagation of the crustal network ruptures. The building of the stations and a first set of measurements were carried out during a first campaign (30 September and 2 October 2016). On 26 October 2016, immediately north of the epicentral area of the 24 August event, another earthquake (Mw = 5.9) occurred, followed 4 days later (30 October) by the main shock (Mw = 6.5) of the whole 2016 summer-autumn seismic sequence. Our local geodetic network was fully affected by the new events and therefore we performed a second campaign soon after (11-13 November 2016). In this brief note, we provide the results of our geodetic measurements that registered the co-seismic and immediately post-seismic deformation of the two major October shocks, documenting in some detail the surface deformation close to the fault trace. We also compare our results with the available surface deformation field of the broader area, obtained on the basis of the DInSAR technique, and show an overall good fit.

Sudden aseismic fault slip on the south flank of Kilauea volcano.

PubMed

Cervelli, Peter; Segall, Paul; Johnson, Kaj; Lisowski, Michael; Miklius, Asta

2002-02-28

One of the greatest hazards associated with oceanic volcanoes is not volcanic in nature, but lies with the potential for catastrophic flank failure. Such flank failure can result in devastating tsunamis and threaten not only the immediate vicinity, but coastal cities along the entire rim of an ocean basin. Kilauea volcano on the island of Hawaii, USA, is a potential source of such flank failures and has therefore been monitored by a network of continuously recording geodetic instruments, including global positioning system (GPS) receivers, tilt meters and strain meters. Here we report that, in early November 2000, this network recorded transient southeastward displacements, which we interpret as an episode of aseismic fault slip. The duration of the event was about 36 hours, it had an equivalent moment magnitude of 5.7 and a maximum slip velocity of about 6[?]cm per day. Inversion of the GPS data reveals a shallow-dipping thrust fault at a depth of 4.5[?]km that we interpret as the down-dip extension of the Hilina Pali--Holei Pali normal fault system. This demonstrates that continuously recording geodetic networks can detect accelerating slip, potentially leading to warnings of volcanic flank collapse.

A Cost-Effective Geodetic Strainmeter Based on Dual Coaxial Cable Bragg Gratings

PubMed Central

Fu, Jihua; Wang, Xu; Wei, Tao; Wei, Meng; Shen, Yang

2017-01-01

Observations of surface deformation are essential for understanding a wide range of geophysical problems, including earthquakes, volcanoes, landslides, and glaciers. Current geodetic technologies, such as global positioning system (GPS), interferometric synthetic aperture radar (InSAR), borehole and laser strainmeters, are costly and limited in their temporal or spatial resolutions. Here we present a new type of strainmeters based on the coaxial cable Bragg grating (CCBG) sensing technology that provides cost-effective strain measurements. Two CCBGs are introduced into the geodetic strainmeter: one serves as a sensor to measure the strain applied on it, and the other acts as a reference to detect environmental noises. By integrating the sensor and reference signals in a mixer, the environmental noises are minimized and a lower mixed frequency is obtained. The lower mixed frequency allows for measurements to be taken with a portable spectrum analyzer, rather than an expensive spectrum analyzer or a vector network analyzer (VNA). Analysis of laboratory experiments shows that the strain can be measured by the CCBG sensor, and the portable spectrum analyzer can make measurements with the accuracy similar to the expensive spectrum analyzer, whose relative error to the spectrum analyzer R3272 is less than ±0.4%. The outputs of the geodetic strainmeter show a linear relationship with the strains that the CCBG sensor experienced. The measured sensitivity of the geodetic strainmeter is about −0.082 kHz/με; it can cover a large dynamic measuring range up to 2%, and its nonlinear errors can be less than 5.3%. PMID:28417925

A Cost-Effective Geodetic Strainmeter Based on Dual Coaxial Cable Bragg Gratings.

PubMed

Fu, Jihua; Wang, Xu; Wei, Tao; Wei, Meng; Shen, Yang

2017-04-12

Observations of surface deformation are essential for understanding a wide range of geophysical problems, including earthquakes, volcanoes, landslides, and glaciers. Current geodetic technologies, such as global positioning system (GPS), interferometric synthetic aperture radar (InSAR), borehole and laser strainmeters, are costly and limited in their temporal or spatial resolutions. Here we present a new type of strainmeters based on the coaxial cable Bragg grating (CCBG) sensing technology that provides cost-effective strain measurements. Two CCBGs are introduced into the geodetic strainmeter: one serves as a sensor to measure the strain applied on it, and the other acts as a reference to detect environmental noises. By integrating the sensor and reference signals in a mixer, the environmental noises are minimized and a lower mixed frequency is obtained. The lower mixed frequency allows for measurements to be taken with a portable spectrum analyzer, rather than an expensive spectrum analyzer or a vector network analyzer (VNA). Analysis of laboratory experiments shows that the strain can be measured by the CCBG sensor, and the portable spectrum analyzer can make measurements with the accuracy similar to the expensive spectrum analyzer, whose relative error to the spectrum analyzer R3272 is less than ±0.4%. The outputs of the geodetic strainmeter show a linear relationship with the strains that the CCBG sensor experienced. The measured sensitivity of the geodetic strainmeter is about -0.082 kHz/με; it can cover a large dynamic measuring range up to 2%, and its nonlinear errors can be less than 5.3%.

A Geodetic Strain Rate Model for the East African Rift System.

PubMed

Stamps, D S; Saria, E; Kreemer, C

2018-01-15

Here we describe the new Sub-Saharan Africa Geodetic Strain Rate Model v.1.0 (SSA-GSRM v.1.0), which provides fundamental constraints on long-term tectonic deformation in the region and an improved seismic hazards assessment in Sub-Saharan Africa. Sub-Saharan Africa encompasses the East African Rift System, the active divergent plate boundary between the Nubian and Somalian plates, where strain is largely accommodated along the boundaries of three subplates. We develop an improved geodetic strain rate field for sub-Saharan Africa that incorporates 1) an expanded geodetic velocity field, 2) redefined regions of deforming zones guided by seismicity distribution, and 3) updated constraints on block rotations. SSA-GSRM v.1.0 spans longitudes 22° to 55.5° and latitudes -52° to 20° with 0.25° (longitude) by 0.2° (latitude) spacing. For plates/sub-plates, we assign rigid block rotations as constraints on the strain rate calculation that is determined by fitting bicubic Bessel splines to a new geodetic velocity solution for an interpolated velocity gradient tensor field. We derive strain rates, velocities, and vorticity rates from the velocity gradient tensor field. A comparison with the Global Geodetic Strain Rate model v2.1 reveals regions of previously unresolved spatial heterogeneities in geodetic strain rate distribution, which indicates zones of elevated seismic risk.

IVS: Current Status and Future Plans

NASA Astrophysics Data System (ADS)

Behrend, D.; Nothnagel, A.; Petrachenko, W. T.; Tuccari, G.

2016-12-01

The International VLBI Service for Geodesy and Astrometry (IVS) is a globally operating service that coordinates and performs Very Long Baseline Interferometry (VLBI) activities through its constituent components. The VLBI activities are associated with the creation, provision, dissemination, and archiving of relevant VLBI data and products. The products mostly pertain to the determination of the celestial and terrestrial reference frames, the Earth orientation parameters (EOP), atmospheric parameters as well as other ancillary parameters. The IVS observational network currently consists of about 40 radio telescopes worldwide. Subsets of these telescopes (8-12 stations) participate in 24-hour observing sessions that are run several times per week and in 1-hour intensive sessions for UT1 determination every day. The current VLBI network was developed mainly in the 1970s and 1980s. A number of factors, including aging infrastructure and demanding new scientific requirements, started to challenge its future sustainability and relevance. In response, the IVS and other groups developed and started implementing the next generation VLBI system, called VGOS (VLBI Global Observing System), at existing and new sites. The VGOS network is expected to reach maturity in the early 2020s. We describe the current status, progress, and anticipated prospects of geodetic/astrometric VLBI and the IVS.

Results from a model-independent method of monitoring a geodetic network for patterns of transient deformation

NASA Technical Reports Server (NTRS)

Hurst, Kenneth; Granat, Robert

2005-01-01

We have implmented two multi-station detectors for transient crustal deformation within the Southern California Integrated GPS (SCGIN). One the the primary goals of SCIGN is to detect transient deformation associated with the earthquake cycle in Southern California.

GSFC VLBI Analysis Center Annual Report

NASA Technical Reports Server (NTRS)

Gordon, David; Ma, Chopo; MacMillan, Dan

1999-01-01

The GSFC VLBI group, located at NASA's Goddard Space Flight Center in Greenbelt, MD, is a part of the NASA Space Geodesy Program. Since its inception in the mid 1970's, this group has been involved with and been a leader in most aspects of geodetic and astrometric VLBI. Current major activities include coordination of the international geodetic observing program; coordination and analysis of the CORE program; VLBI technique development; and all types of data processing, analysis, and research activities.

Absolute Gravity Datum in the Age of Cold Atom Gravimeters

NASA Astrophysics Data System (ADS)

Childers, V. A.; Eckl, M. C.

2014-12-01

The international gravity datum is defined today by the International Gravity Standardization Net of 1971 (IGSN-71). The data supporting this network was measured in the 1950s and 60s using pendulum and spring-based gravimeter ties (plus some new ballistic absolute meters) to replace the prior protocol of referencing all gravity values to the earlier Potsdam value. Since this time, gravimeter technology has advanced significantly with the development and refinement of the FG-5 (the current standard of the industry) and again with the soon-to-be-available cold atom interferometric absolute gravimeters. This latest development is anticipated to provide improvement in the range of two orders of magnitude as compared to the measurement accuracy of technology utilized to develop ISGN-71. In this presentation, we will explore how the IGSN-71 might best be "modernized" given today's requirements and available instruments and resources. The National Geodetic Survey (NGS), along with other relevant US Government agencies, is concerned about establishing gravity control to establish and maintain high order geodetic networks as part of the nation's essential infrastructure. The need to modernize the nation's geodetic infrastructure was highlighted in "Precise Geodetic Infrastructure, National Requirements for a Shared Resource" National Academy of Science, 2010. The NGS mission, as dictated by Congress, is to establish and maintain the National Spatial Reference System, which includes gravity measurements. Absolute gravimeters measure the total gravity field directly and do not involve ties to other measurements. Periodic "intercomparisons" of multiple absolute gravimeters at reference gravity sites are used to constrain the behavior of the instruments to ensure that each would yield reasonably similar measurements of the same location (i.e. yield a sufficiently consistent datum when measured in disparate locales). New atomic interferometric gravimeters promise a significant increase in accuracy. Our presentation will also explore the impact of such an instrument on our theory of how to constrain the gravity datum and on how to ensure stability, repeatability, and reproducibility across different absolute gravimeter systems.

West-Coast Wide Expansion and Testing of the Geodetic Alarm System (G-larmS)

NASA Astrophysics Data System (ADS)

Ruhl, C. J.; Grapenthin, R.; Melgar, D.; Aranha, M. A.; Allen, R. M.

2016-12-01

The Geodetic Alarm System (G-larmS) was developed in collaboration between the Berkeley Seismological Laboratory (BSL) and New Mexico Tech for real-time Earthquake Early Warning (EEW). G-larmS has been in continuous operation at the BSL since 2014 using event triggers from the ShakeAlert EEW system and real-time position time series from a fully triangulated network consisting of BARD, PBO and USGS stations across northern California (CA). G-larmS has been extended to include southern CA and Cascadia, providing continuous west-coast wide coverage. G-larmS currently uses high rate (1 Hz), low latency (< 5 s), accurate positioning (cm level) time series data from a regional GPS network and P-wave event triggers from the ShakeAlert EEW system. It extracts static offsets from real-time GPS time series upon S-wave arrival and performs a least squares inversion on these offsets to determine slip on a finite fault. A key issue with geodetic EEW approaches is that unlike seismology-based algorithms that are routinely tested using frequent small-magnitude events, geodetic systems are not regularly exercised. Scenario ruptures are therefore important for testing the performance of G-larmS. We discuss results from scenario events on several large faults (capable of M>6.5) in CA and Cascadia built from realistic 3D geometries. Synthetic long-period 1Hz displacement waveforms were obtained from a new stochastic kinematic slip distribution generation method. Waveforms are validated by direct comparison to peak P-wave displacement scaling laws and to PGD GMPEs obtained from high-rate GPS observations of large events worldwide. We run the scenarios on real-time streams to systematically test the recovery of slip and magnitude by G-larmS. In addition to presenting these results, we will discuss new capabilities, such as implementing 2D geometry and the applicability of these results to GPS enhanced tsunami warning systems.

GNSS CORS hardware and software enabling new science

NASA Astrophysics Data System (ADS)

Drummond, P.

2009-12-01

GNSS CORS networks are enabling new opportunities for science and public and private sector business. This paper will explore how the newest geodetic monitoring software and GNSS receiver hardware from Trimble Navigation Ltd are enabling new science. Technology trends and science opportunities will be explored. These trends include the installation of active GNSS control, automation of observations and processing, and the advantages of multi-observable and multi-constellation observations, all performed with the use of off the shelf products and industry standard open-source data formats. Also the possibilities with moving science from an after-the-fact postprocessed model to a real-time epoch-by-epoch solution will be explored. This presentation will also discuss the combination of existing GNSS CORS networks with project specific installations used for monitoring. Experience is showing GNSS is able to provide higher resolution data than previous methods, providing new tools for science, decision makers and financial planners.

LIBRA: An inexpensive geodetic network densification system

NASA Technical Reports Server (NTRS)

Fliegel, H. F.; Gantsweg, M.; Callahan, P. S.

1975-01-01

A description is given of the Libra (Locations Interposed by Ranging Aircraft) system, by which geodesy and earth strain measurements can be performed rapidly and inexpensively to several hundred auxiliary points with respect to a few fundamental control points established by any other technique, such as radio interferometry or satellite ranging. This low-cost means of extending the accuracy of space age geodesy to local surveys provides speed and spatial resolution useful, for example, for earthquake hazards estimation. Libra may be combined with an existing system, Aries (Astronomical Radio Interferometric Earth Surveying) to provide a balanced system adequate to meet the geophysical needs, and applicable to conventional surveying. The basic hardware design was outlined and specifications were defined. Then need for network densification was described. The following activities required to implement the proposed Libra system are also described: hardware development, data reduction, tropospheric calibrations, schedule of development and estimated costs.

Network global navigation satellite system survey to harmonize water-surface elevation data for the Rainy River Basin

USGS Publications Warehouse

Ziegeweid, Jeffrey R.; Silliker, R. Jason; Densmore, Brenda K.; Krahulik, Justin

2016-08-15

Continuously recording water-level streamgages in Rainy Lake and Namakan Reservoir are used to regulate water levels according to rule curves established in 2000 by the International Joint Commission; however, water levels at streamgages were referenced to a variety of vertical datums, confounding efforts to model the flow of water through the system, regulate water levels during periods of high inflow, and evaluate the effectiveness of the rule curves. In October 2014, the U.S. Geological Survey, Natural Resources Canada, International Joint Commission, and National Park Service began a joint field study with the goal of obtaining precise elevations referenced to a uniform vertical datum for all reference marks used to set water levels at streamgages throughout Rainy Lake and Namakan Reservoir. This report was prepared by the U.S. Geological Survey in cooperation with Natural Resources Canada, International Joint Commission, and National Park Service.Three field crews deployed Global Navigation Satellite System receivers statically over 16 reference marks colocated with active and discontinued water-level streamgages throughout Rainy River, Rainy Lake, Namakan Reservoir, and select tributaries of Rainy Lake and Namakan Reservoir. A Global Navigation Satellite System receiver also was deployed statically over a National Geodetic Survey cooperative base network control station for use as a quality-control reference mark. Satellite data were collected simultaneously during a 5-day period and processed independently by the U.S. Geological Survey and Natural Resources Canada to obtain accurate positioning and elevations for the 17 surveyed reference marks. Processed satellite data were used to convert published water levels to elevations above sea level referenced to the Canadian Geodetic Vertical Datum of 2013 in order to compare water-surface elevations referenced to a uniform vertical datum throughout the study area. In this report, an “offset” refers to the correction applied to published data from a particular streamgage to produce elevation data referenced to a specified vertical datum.Offsets were applied to water-level data from surveyed streamgages to further evaluate the accuracy and utility of updated reference mark elevations presented in this report. Daily mean water levels from active streamgages surveyed in this study were converted to water-surface elevations referenced to the Canadian Geodetic Vertical Datum of 2013. Graphical comparisons of water-surface elevations for streamgages in Namakan Reservoir, Rainy Lake, and selected rivers are presented (referencing the Canadian Geodetic Vertical Datum of 2013). Offsets presented in this report can be used in the evaluation of rule curves and in flood damage curves that fully assess the benefits of one regulation approach over another. In addition, offsets may be used to calibrate hydraulic models developed for four narrows that connect lakes of Namakan Reservoir, refine digital elevation models, and support modeling studies designed to assess the effects of rule curves on aquatic vegetation, benthic invertebrates, northern pike, and walleye.

Deformation offshore Northern Chile monitored by a seafloor geodetic network (GeoSEA)

NASA Astrophysics Data System (ADS)

Hannemann, Katrin; Lange, Dietrich; Kopp, Heidrun; Petersen, Florian; Contreras-Reyes, Eduardo

2017-04-01

The Nazca-South American plate boundary around 21°S has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique earthquake (Mw=8.1). The southern portion of this segment is still unbroken. The geodetic monitoring of the Chilean subduction zone is crucial to understand the deformation processes in this area. Most geodetic measurements rely on GPS and are therefore limited to onshore campaigns. In December 2015, we installed the GeoSEA (Geodetic Earthquake Observatory on the SEAfloor) array around 21°S of the Nazca-South American plate boundary with RV SONNE to extend the geodetic observations to the offshore areas. The GeoSEA array consists of autonomous acoustic seafloor transponders mounted on 4 m high tripods. These transponders are able to continuously measure the two-way travel time of acoustic signals between station pairs (baselines) and the properties of the sea water (sound speed, temperature and pressure) at each transponder. These measurements are used to retrieve the distances between the transponders and give insights into the deformation of the seafloor. At the Chilean subduction zone, we installed in total 23 transponders in 3 subarrays with interstation distances of up to 2500 m. On the middle continental slope in 2300 m water depth, an array consisting of 8 transponders measures across crustal faults seen in AUV mapping. A second array of 5 stations located on the outer rise monitors extension across normal plate-bending faults. The deepest deployment in 5000 m water depth located on the lower continental slope with 10 stations is designed to measure diffuse strain build-up. The transponders are intended to monitor the seafloor deformation for 3.5 years. In November 2016 during a cruise of RV Langseth, the first 11 months of data were successfully uploaded via an acoustic modem. Furthermore, an additional component of the network, GeoSURF, a self-steering autonomous vehicle (wave glider), was successfully used to monitor system health and to upload parts of the data from the seafloor stations. The first 11 months of data show a good signal quality and the baseline precision is ± 5 mm. The data reveals no deformation above the resolution limits of the individual distance measurements.

Development of a System to Generate Near Real Time Tropospheric Delay and Precipitable Water Vapor in situ at Geodetic GPS Stations, to Improve Forecasting of Severe Weather Events

NASA Astrophysics Data System (ADS)

Moore, A. W.; Bock, Y.; Geng, J.; Gutman, S. I.; Laber, J. L.; Morris, T.; Offield, D. G.; Small, I.; Squibb, M. B.

2012-12-01

We describe a system under development for generating ultra-low latency tropospheric delay and precipitable water vapor (PWV) estimates in situ at a prototype network of geodetic GPS sites in southern California, and demonstrating their utility in forecasting severe storms commonly associated with flooding and debris flow events along the west coast of North America through infusion of this meteorological data at NOAA National Weather Service (NWS) Forecast Offices and the NOAA Earth System Research Laboratory (ESRL). The first continuous geodetic GPS network was established in southern California in the early 1990s and much of it was converted to real-time (latency <1s) high-rate (1Hz) mode over the following decades. GPS stations are multi-purpose and can also provide estimates of tropospheric zenith delays, which can be converted into mm-accuracy PWV using collocated pressure and temperature measurements, the basis for GPS meteorology (Bevis et al. 1992, 1994; Duan et al. 1996) as implemented by NOAA with a nationwide distribution of about 300 GPS-Met stations providing PW estimates at subhourly resolution currently used in operational weather forecasting in the U.S. We improve upon the current paradigm of transmitting large quantities of raw data back to a central facility for processing into higher-order products. By operating semi-autonomously, each station will provide low-latency, high-fidelity and compact data products within the constraints of the narrow communications bandwidth that often occurs in the aftermath of natural disasters. The onsite ambiguity-resolved precise point positioning solutions are enabled by a power-efficient, low-cost, plug-in Geodetic Module for fusion of data from in situ sensors including GPS and a low-cost MEMS meteorological sensor package. The decreased latency (~5 minutes) PW estimates will provide the detailed knowledge of the distribution and magnitude of PW that NWS forecasters require to monitor and predict severe winter storms, landfalling atmospheric rivers, and summer thunderstorms associated with the North American monsoon. On the national level, the ESRL will evaluate the utility of ultra-low resolution GNSS observations to improve NOAA's warning and forecast capabilities. The overall objective is to better forecast, assess, and mitigate natural hazards through the flow of information from multiple geodetic stations to scientists, mission planners, decision makers, and first responders.

Plans for a Northern Cascadia Subduction Zone Observatory

NASA Astrophysics Data System (ADS)

Heesemann, M.; Wang, K.; Davis, E.; Chadwell, C. D.; Nissen, E.; Moran, K.; Scherwath, M.

2017-12-01

To accurately assess earthquake and tsunami hazards posed by the Cascadia Subduction Zone, it is critically important to know which area of the plate interface is locked and whether or not part of the energy is being released aseismically by slow creep on the fault. Deeper locking that extends further to the coast produces stronger shaking in population centers. Shallow locking, on the other hand, leads to bigger tsunamis. We will report on and discuss plans for a new amphibious Northern Cascadia Subduction Zone Observatory (NCSZO) that will leverage the existing NEPTUNE cabled seafloor observatory, which is operated by Ocean Networks Canada (ONC), and the onshore network of geodetic stations, which is operated by Natural Resources Canada (NRCan). To create a NCSZO we plan to (1) add a network of seven GPS-Acoustic (GPS-A) sites offshore Vancouver Island, (2) establish a Deformation Front Observatory, and (3) improve the existing onshore geodetic network (see Figure below). The GPS-A stations will provide the undisturbed motion of the Juan de Fuca (JdF) Plate (1), deformation of the JdF plate (2), deformation of the overriding plate (3-7) and a cabled laboratory to study the potential for continuous GPS-A measurements (6). The Deformation Front Observatory will be used to study possible transient slip events using seafloor pressure and tilt instruments and fluid flux meters.

Experience with the ULISS-30 inertial survey system for local geodetic and cadastral network control

NASA Astrophysics Data System (ADS)

Forsberg, Rene

1991-09-01

The capability of the recently developed SAGEM ULISS-30 inertial survey system for performing local surveys at high accuracies have been tested in a field campaign carried out November 1989 on the island of Fyn, Denmark, in cooperation with the Swedish National Land Survey. In the test a number of lines between existing national geodetic control points were surveyed, along with points in the less reliably determined cadastral network, forming an irregular network pattern of 10 15 km extent. The survey involved frequent offset measurements (up to 50 100 m) with an ISS-integrated total station. The profile geometries were not particularly suited for inertial surveys, with narrow and rather winding roads, necessitating frequent vehicle turns. In addition to the pure inertial surveys a kinematic GPS/inertial test was also carried out, using a pair of Ashtech L-XII receivers. The inertial survey results, analyzed with a smoothing algoritm utilizing common points on forward/backward runs, indicate that 5-cm accuracies are possible on reasonably straight profiles of 5 km length, corresponding to a 10 ppm “best-case” accuracy for double-run traverses. On longer, more winding traverses error levels of 10 20 cm are typical. To handle the inertial data optimally, proper network adjustments are required. A discussion of suitable adjustment models of both conventional and collocation type is included in the paper.

Optimization of deformation monitoring networks using finite element strain analysis

NASA Astrophysics Data System (ADS)

Alizadeh-Khameneh, M. Amin; Eshagh, Mehdi; Jensen, Anna B. O.

2018-04-01

An optimal design of a geodetic network can fulfill the requested precision and reliability of the network, and decrease the expenses of its execution by removing unnecessary observations. The role of an optimal design is highlighted in deformation monitoring network due to the repeatability of these networks. The core design problem is how to define precision and reliability criteria. This paper proposes a solution, where the precision criterion is defined based on the precision of deformation parameters, i. e. precision of strain and differential rotations. A strain analysis can be performed to obtain some information about the possible deformation of a deformable object. In this study, we split an area into a number of three-dimensional finite elements with the help of the Delaunay triangulation and performed the strain analysis on each element. According to the obtained precision of deformation parameters in each element, the precision criterion of displacement detection at each network point is then determined. The developed criterion is implemented to optimize the observations from the Global Positioning System (GPS) in Skåne monitoring network in Sweden. The network was established in 1989 and straddled the Tornquist zone, which is one of the most active faults in southern Sweden. The numerical results show that 17 out of all 21 possible GPS baseline observations are sufficient to detect minimum 3 mm displacement at each network point.

The Australian Geodetic Observing Program. Current Status and Future Plans

NASA Astrophysics Data System (ADS)

Johnston, G.; Dawson, J. H.

2015-12-01

Over the last decade, the Australian government has through programs like AuScope, the Asia Pacific Reference Frame (APREF), and the Pacific Sea Level Monitoring (PSLM) Project made a significant contribution to the Global Geodetic Observing Program. In addition to supporting the national research priorities, this contribution is justified by Australia's growing economic dependence on precise positioning to underpin efficient transportation, geospatial data management, and industrial automation (e.g., robotic mining and precision agriculture) and the consequent need for the government to guarantee provision of precise positioning products to the Australian community. It is also well recognised within Australia that there is an opportunity to exploit our near unique position as being one of the few regions in the world to see all new and emerging satellite navigation systems including Galileo (Europe), GPS III (USA), GLONASS (Russia), Beidou (China), QZSS (Japan) and IRNSS (India). It is in this context that the Australian geodetic program will build on earlier efforts and further develop its key geodetic capabilities. This will include the creation of an independent GNSS analysis capability that will enable Australia to contribute to the International GNSS Service (IGS) and an upgrade of key geodetic infrastructure including the national VLBI and GNSS arrays. This presentation will overview the significant geodetic activities undertaken by the Australian government and highlight its future plans.

Geodetic reanalysis of annual glaciological mass balances (2001-2011) of Hintereisferner, Austria

NASA Astrophysics Data System (ADS)

Klug, Christoph; Bollmann, Erik; Galos, Stephan Peter; Nicholson, Lindsey; Prinz, Rainer; Rieg, Lorenzo; Sailer, Rudolf; Stötter, Johann; Kaser, Georg

2018-03-01

This study presents a reanalysis of the glaciologically obtained annual glacier mass balances at Hintereisferner, Ötztal Alps, Austria, for the period 2001-2011. The reanalysis is accomplished through a comparison with geodetically derived mass changes, using annual high-resolution airborne laser scanning (ALS). The grid-based adjustments for the method-inherent differences are discussed along with associated uncertainties and discrepancies of the two methods of mass balance measurements. A statistical comparison of the two datasets shows no significant difference for seven annual, as well as the cumulative, mass changes over the 10-year record. Yet, the statistical view hides significant differences in the mass balance years 2002/03 (glaciological minus geodetic records = +0.92 m w.e.), 2005/06 (+0.60 m w.e.), and 2006/07 (-0.45 m w.e.). We conclude that exceptional meteorological conditions can render the usual glaciological observational network inadequate. Furthermore, we consider that ALS data reliably reproduce the annual mass balance and can be seen as validation or calibration tools for the glaciological method.

Production and Uses of Multi-Decade Geodetic Earth Science Data Records

NASA Astrophysics Data System (ADS)

Bock, Y.; Kedar, S.; Moore, A. W.; Fang, P.; Liu, Z.; Sullivan, A.; Argus, D. F.; Jiang, S.; Marshall, S. T.

2017-12-01

The Solid Earth Science ESDR System (SESES) project funded under the NASA MEaSUREs program produces and disseminates mature, long-term, calibrated and validated, GNSS based Earth Science Data Records (ESDRs) that encompass multiple diverse areas of interest in Earth Science, such as tectonic motion, transient slip and earthquake dynamics, as well as meteorology, climate, and hydrology. The ESDRs now span twenty-five years for the earliest stations and today are available for thousands of global and regional stations. Using a unified metadata database and a combination of GNSS solutions generated by two independent analysis centers, the project currently produces four long-term ESDR's: Geodetic Displacement Time Series: Daily, combined, cleaned and filtered, GIPSY and GAMIT long-term time series of continuous GPS station positions (global and regional) in the latest version of ITRF, automatically updated weekly. Geodetic Velocities: Weekly updated velocity field + velocity field histories in various reference frames; compendium of all model parameters including earthquake catalog, coseismic offsets, and postseismic model parameters (exponential or logarithmic). Troposphere Delay Time Series: Long-term time series of troposphere delay (30-min resolution) at geodetic stations, necessarily estimated during position time series production and automatically updated weekly. Seismogeodetic records for historic earthquakes: High-rate broadband displacement and seismic velocity time series combining 1 Hz GPS displacements and 100 Hz accelerometer data for select large earthquakes and collocated cGPS and seismic instruments from regional networks. We present several recent notable examples of the ESDR's usage: A transient slip study that uses the combined position time series to unravel "tremor-less" slow tectonic transient events. Fault geometry determination from geodetic slip rates. Changes in water resources across California's physiographic provinces at a spatial resolution of 75 km. Retrospective study of a southern California summer monsoon event.

Geodetic Seamless Archive Centers Modernization - Information Technology for Exploiting the Data Explosion

NASA Astrophysics Data System (ADS)

Boler, F. M.; Blewitt, G.; Kreemer, C. W.; Bock, Y.; Noll, C. E.; McWhirter, J.; Jamason, P.; Squibb, M. B.

2010-12-01

Space geodetic science and other disciplines using geodetic products have benefited immensely from open sharing of data and metadata from global and regional archives Ten years ago Scripps Orbit and Permanent Array Center (SOPAC), the NASA Crustal Dynamics Data Information System (CDDIS), UNAVCO and other archives collaborated to create the GPS Seamless Archive Centers (GSAC) in an effort to further enable research with the expanding collections of GPS data then becoming available. The GSAC partners share metadata to facilitate data discovery and mining across participating archives and distribution of data to users. This effort was pioneering, but was built on technology that has now been rendered obsolete. As the number of geodetic observing technologies has expanded, the variety of data and data products has grown dramatically, exposing limitations in data product sharing. Through a NASA ROSES project, the three archives (CDDIS, SOPAC and UNAVCO) have been funded to expand the original GSAC capability for multiple geodetic observation types and to simultaneously modernize the underlying technology by implementing web services. The University of Nevada, Reno (UNR) will test the web services implementation by incorporating them into their daily GNSS data processing scheme. The effort will include new methods for quality control of current and legacy data that will be a product of the analysis/testing phase performed by UNR. The quality analysis by UNR will include a report of the stability of the stations coordinates over time that will enable data users to select sites suitable for their application, for example identifying stations with large seasonal effects. This effort will contribute to enhanced ability for very large networks to obtain complete data sets for processing.

Geodetic slip rate estimates for the Alhama de Murcia and Carboneras faults in the SE Betics, Spain

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Echeverria, Anna; Masana, Eulàlia

2016-04-01

The Alhama de Murcia and the Carboneras faults are the most prominent geologic structures within the Eastern Betic Shear Zone (EBSZ), located in SE Spain. Using continuous and campaign GPS observations conducted during the last decade, we were able to confirm the continuing tectonic activity of these faults by quantifying their geodetic slip-rates and comparing the estimated values with the geological (including paleoseismological) observations. We find that the bulk of the observed deformation is concentrated around the Alhama de Murcia (AMF) and the Palomares (PF) faults. The geodetic horizontal slip rate (reverse-sinistral) of 1.5±0.3 mm/yr calculated for the AMF and PF fault system is in good agreement with geological observations at the AMF, as well as, the focal mechanism of the 2011 Lorca earthquake, suggesting a main role of the AMF. We also find that the geodetic slip rate of the Carboneras fault zone (CFZ) is almost purely sinistral strike-slip with a rate of 1.3±0.2 mm/yr along N48° direction, very similar to 1.1 mm/yr geologic slip-rate, estimated from recent onshore and offshore paleoseismic and geomorphologic studies. The fact the geodetic and the geologic slip-rates are similar at the AMF and CF faults, suggests that both faults have been tectonically active since Quaternary, slipping at approximately at constant rate of 1.1 to 1.8 mm/yr. Since the existing GPS data cannot discern whether the CFZ is slipping seismically or aseismically, we have intended to relate the on-going seismic activity to the slip-rates estimated using GPS. For this reason we compared seismic and geodetic strain rates, where the latter are larger than seismic strain rates, suggesting the presence of aseismic processes in the area. Nevertheless, due to the large earthquake recurrence intervals, we may be underestimating the seismic strain rates. The direction of the P and T average stress axes are in good agreement with geodetic principal strain rate axes. To summarize, in eastern Betics, Alhama de Murcia and Carboneras left-lateral faults are the most active faults and they play an important role in the regional plate convergence kinematics. The work has been supported by the Spanish Ministry of Science and Innovation projects: SHAKE (CGL2011-30005-C02-01), CHARMA (CGL2013-40828-R) and EVENT (CGL2006-12861-C02-01).

Volcano geodesy: Challenges and opportunities for the 21st century

USGS Publications Warehouse

Dzurisin, D.

2000-01-01

Intrusions of magma beneath volcanoes deform the surrounding rock and, if the intrusion is large enough, the overlying ground surface. Numerical models generally agree that, for most eruptions, subsurface volume changes are sufficient to produce measurable deformation at the surface. Studying this deformation can help to determine the location, volume, and shape of a subsurface magma body and thus to anticipate the onset and course of an eruption. This approach has been successfully applied at many restless volcanoes, especially basaltic shields and silicic calderas, using various geodetic techniques and sensors. However, its success at many intermediate-composition strato-volcanoes has been limited by generally long repose intervals, steep terrain, and structural influences that complicate the history and shape of surface deformation. These factors have made it difficult to adequately characterize deformation in space and time at many of the world's dangerous volcanoes. Recent technological advances promise to make this task easier by enabling the acquisition of geodetic data of high spatial and temporal resolution from Earth-orbiting satellites. Synthetic aperture radar interferometry (InSAR) can image ground deformation over large areas at metre-scale resolution over time-scales of a month to a few years. Global Positioning System (GPS) stations can provide continuous information on three-dimensional ground displacements at a network of key sites -information that is especially important during volcanic crises. By using InSAR to determine the shape of the displacement field and GPS to monitor temporal changes at key sites, scientists have a much better chance to capture geodetic signals that have so far been elusive at many volcanoes. This approach has the potential to provide longer-term warnings of impending volcanic activity than is possible with other monitoring techniques.

Integration of the Plate Boundary Observatory and Existing GPS Networks in Southern California: A Multi Use Geodetic Network

NASA Astrophysics Data System (ADS)

Walls, C.; Blume, F.; Meertens, C.; Arnitz, E.; Lawrence, S.; Miller, S.; Bradley, W.; Jackson, M.; Feaux, K.

2007-12-01

The ultra-stable GPS monument design developed by Southern California Geodetic Network (SCIGN) in the late 1990s demonstrates sub-millimeter errors on long time series where there are a high percentage of observations and low multipath. Following SCIGN, other networks such as PANGA and BARGEN have adopted the monument design for both deep drilled braced monuments (DDBM = 5 legs grouted 10.7 meters into bedrock/stratigraphy) and short drilled braced monuments (SDBM = 4 legs epoxied 2 meters into bedrock). A Plate Boundary Observatory (PBO) GPS station consists of a "SCIGN" style monument and state of the art NetRS receiver and IP based communications. Between the years 2003-2008 875 permanent PBO GPS stations are being built throughout the United States. Concomitant with construction of the PBO the majority of pre-existing GPS stations that meet stability specifications are being upgraded with Trimble NetRS and IP based communications to PBO standards under the EarthScope PBO Nucleus project. In 2008, with completed construction of the Plate Boundary Observatory, more than 1100 GPS stations will share common design specifications and have identical receivers with common communications making it the most homogenous geodetic network in the World. Of the 875 total Plate Boundary Observatory GPS stations, 211 proposed sites are distributed throughout the Southern California region. As of August 2007 the production status is: 174 stations built (81 short braced monuments, 93 deep drilled braced monuments), 181 permits signed, 211 permits submitted and 211 station reconnaissance reports. The balance of 37 stations (19 SDBM and 18 DDBM) will be built over the next year from Long Valley to the Mexico border in order of priority as recommended by the PBO Transform, Extension and Magmatic working groups. Fifteen second data is archived for each station and 1 Hz as well as 5 Hz data is buffered to be triggered for download in the event of an earthquake. Communications equipment includes CDMA Proxicast modems, Hughes Vsat, Intuicom 900 MHz Ethernet bridge radios and several "real-time" sites use 2.4 GHz Wilan radios. Ultimately, 125 of the existing former-SCIGN GPS stations will be integrated into the So Cal region of PBO, of which 25 have real-time data streams. At the time of this publication the total combined Southern California region has over 40 stations streaming real-time data using both radios and CDMA modems. The real-time GPS sites provide specific benefits beyond the standard GPS station: they can provide a live correction for local surveyors and can be used to trigger an alarm if large displacements are recorded. The cross fault spatial distribution of these 336 GPS stations in the seismically active southern California region has the grand potential of augmenting a strong motion earthquake early warning system.

An Overview of Geodetic Volcano Research in the Canary Islands

NASA Astrophysics Data System (ADS)

Fernández, José; González, Pablo J.; Camacho, Antonio G.; Prieto, Juan F.; Brú, Guadalupe

2015-11-01

The Canary Islands are mostly characterized by diffuse and scattered volcanism affecting a large area, with only one active stratovolcano, the Teide-Pico Viejo complex (Tenerife). More than 2 million people live and work in the 7,447 km2 of the archipelago, resulting in an average population density three times greater than the rest of Spain. This fact, together with the growth of exposure during the past 40 years, increases volcanic risk with respect previous eruptions, as witnessed during the recent 2011-2012 El Hierro submarine eruption. Therefore, in addition to purely scientific reasons there are economic and population-security reasons for developing and maintaining an efficient volcano monitoring system. In this scenario geodetic monitoring represents an important part of the monitoring system. We describe volcano geodetic monitoring research carried out in the Canary Islands and the results obtained. We consider for each epoch the two main existing constraints: the level of volcanic activity in the archipelago, and the limitations of the techniques available at the time. Theoretical and observational aspects are considered, as well as the implications for operational volcano surveillance. Current challenges of and future perspectives in geodetic volcano monitoring in the Canaries are also presented.

Afar-wide Crustal Strain Field from Multiple InSAR Tracks

NASA Astrophysics Data System (ADS)

Pagli, C.; Wright, T. J.; Wang, H.; Calais, E.; Bennati Rassion, L. S.; Ebinger, C. J.; Lewi, E.

2010-12-01

Onset of a rifting episode in the Dabbahu volcanic segment, Afar (Ethiopia), in 2005 renewed interest in crustal deformation studies in the area. As a consequence, an extensive geodetic data set, including InSAR and GPS measurements have been acquired over Afar and hold great potential towards improving our understanding of the extensional processes that operate during the final stages of continental rupture. The current geodetic observational and modelling strategy has focused on detailed, localised studies of dyke intrusions and eruptions mainly in the Dabbahu segment. However, an eruption in the Erta ‘Ale volcanic segment in 2008, and cluster of earthquakes observed in the Tat Ale segment, are testament to activity elsewhere in Afar. Here we make use of the vast geodetic dataset available to obtain strain information over the whole Afar depression. A systematic analysis of all the volcanic segments, including Dabbahu, Manda-Hararo, Alayta, Tat ‘Ale Erta Ale and the Djibouti deformation zone, is undertaken. We use InSAR data from multiple tracks together with available GPS measurements to obtain a velocity field model for Afar. We use over 300 radar images acquired by the Envisat satellite in both descending and ascending orbits, from 12 distinct tracks in image and wide swath modes, spanning the time period from October 2005 to present time. We obtain the line-of-sight deformation rates from each InSAR track using a network approach and then combine the InSAR velocities with the GPS observations, as suggested by Wright and Wang (2010) following the method of England and Molnar (1997). A mesh is constructed over the Afar area and then we solve for the horizontal and vertical velocities on each node. The resultant full 3D Afar-wide velocity field shows where current strains are being accumulated within the various volcanic segments of Afar, the width of the plate boundary deformation zone and possible connections between distinct volcanic segments on a regional scale. A comparison of crustal strains from the geodetic analysis with the seismicity data will also be made.

VLBI2010: Networks and Observing Strategies

NASA Technical Reports Server (NTRS)

Petrachenko, Bill; Corey, Brian; Himwich, Ed; Ma, Chopo; Malkin, Zinovy; Niell, Arthur; Shaffer, David; Vandenberg, Nancy

2004-01-01

The Observing Strategies Sub-group of IVS's Working Group 3 has been tasked with producing a vision for the following aspects of geodetic VLBI: antenna-network structure and observing strategies; source strength/structure/distribution; frequency bands, RFI; and field system and scheduling. These are high level considerations that have far reaching impact since they significantly influence performance potential and also constrain requirements for a number of other \\VG3 sub-groups. The paper will present the status of the sub-group's work on these topics.

Development and Implementation of Joint Programs in Laser Ranging and Other Space Geodetic Techniques

NASA Technical Reports Server (NTRS)

Pearlman, Michael R.; Carter, David (Technical Monitor)

2004-01-01

This progress report discusses the status and progress made in joint international programs including: 1) WEGENER; 2) Arabian Peninsula program; 3) Asia-Pacific Space Geodynamics (APSG) program; 4) the Fourteenth International Workshop on Laser Ranging; 5) the International Laser Ranging Service; and 6) current support for the NASA network.

Coseismic deformation of the destructive April 6, 2009 L'Aquila earthquake (central Italy) from GPS data

NASA Astrophysics Data System (ADS)

Anzidei, M.; Boschi, E.; Cannelli, V.; Devoti, R.; Esposito, A.; Galvani, A.; Melini, D.; Pietrantonio, G.; Riguzzi, F.; Sepe, V.; Serpelloni, E.

2009-09-01

On April 6, 2009, 01:32:39 GMT, the city of L'Aquila was struck by a Mw 6.3 earthquake that killed 307 people, causing severe destruction and ground cracks in a wide area around the epicenter. Four days before the main shock we augmented the existing permanent GPS network with five GPS stations of the Central Apennine Geodetic Network (CaGeoNet) bordering the L'Aquila basin. The maximum horizontal and vertical coseismic surface displacements detected at these stations was 10.39 ± 0.45 cm and -15.64 ± 1.55 cm, respectively. Fixing the strike direction according to focal mechanism estimates, we estimated the source geometry with a non linear inversion of the geodetic data. Our best fitting fault model is a 13 × 15.7 km2 rectangular fault, SW-dipping at 55.3 ± 1.8°, consistent with the position of observed surface ruptures. The estimated slip (495 ± 29 mm) corresponds to a 6.3 moment magnitude, in excellent agreement with seismological data.

Special issue: The changing shapes of active volcanoes: Recent results and advances in volcano geodesy

USGS Publications Warehouse

Poland, Michael P.; Newman, Andrew V.

2006-01-01

The 18 papers herein report on new geodetic data that offer valuable insights into eruptive activity and magma transport; they present new models and modeling strategies that have the potential to greatly increase understanding of magmatic, hydrothermal, and volcano-tectonic processes; and they describe innovative techniques for collecting geodetic measurements from remote, poorly accessible, or hazardous volcanoes. To provide a proper context for these studies, we offer a short review of the evolution of volcano geodesy, as well as a case study that highlights recent advances in the field by comparing the geodetic response to recent eruptive episodes at Mount St. Helens. Finally, we point out a few areas that continue to challenge the volcano geodesy community, some of which are addressed by the papers that follow and which undoubtedly will be the focus of future research for years to come.

Verification of the Polish Geodetic Reference Frame by Means of a New Solution Based on Permanent GNSS Data from the Years 2011-2014

NASA Astrophysics Data System (ADS)

Liwosz, T.; Ryczywolski, M.

2016-12-01

The new solution for the Polish geodetic primary GNSS network was created to verify the currently used reference frame (PL-ETRF2000). The new solution is based on more GNSS data (more daily observation sessions included, a longer data timespan, GLONASS observations added) which were processed in a newer reference frame (IGb08) according to up-to-date methodology and using the latest version of Bernese GNSS Software. The new long-term solution (spanning 3.7 years) was aligned to the IGb08 reference frame using a minimum constraints approach. We categorized Polish reference stations into two categories according to their data length. We obtained good agreement of the new solution with the PL-ETRF2000: for most stations position differences did not exceed 5 mm in horizontal, and 10 mm in vertical components. However, for 30 stations we observed discontinuities in position time series, mostly due to GNSS equipment changes, which occured after the introduction of PL-ETRF2000. Position changes due to the discontinuities reached 9.1 mm in horizontal components, and 26.9 mm in vertical components. The new solution takes into account position discontinuities, and in addition also includes six new stations which were installed after the introduction of the PL-ETRF2000. Therefore, we propose to update the currently-used reference frame for the Polish geodetic primary network (PL-ETRF2000) with the new solution. The new solution was also accepted by the EUREF Technical Working Group as a class A solution (highest accuracy) according to EUREF standards.

Towards Cloud Processing of GGOS Big Data

NASA Astrophysics Data System (ADS)

Weston, Stuart; Kim, Bumjun; Litchfield, Alan; Gulyaev, Sergei; Hall, Dylan; Chorao, Carlos; Ruthven, Andrew; Davies, Glyn; Lagos, Bruno; Christie, Don

2017-04-01

We report on our initial steps towards development of a cloud-like correlation infrastructure for geodetic Very Long Baseline Interferometry (VLBI), which in its raw format is of the order of 10-100 TB (big data). Data is generated by multiple VLBI radio telescopes, and is then used by for geodetic, geophysical, and astrometric research and operational activities through the International VLBI Service (IVS), as well as for corrections of GPS satellite orbits. Currently IVS data is correlated in several international Correlators (Correlation Centres), which receive data from individual radio telescope stations either in hard drives via regular mail service or via fibre using e-transfer mode. The latter is strongly limited by connectivity of existing correlation centres, which creates bottle necks and slows down the turnover of the data. This becomes critical in many applications - for example, it currently takes 1-2 weeks to generate the dUT1 parameter for corrections of GNSS orbits while less than 1-2 days delay is desirable. We started with a blade server at the AUT campus to emulate a cloud server using Virtual Machines (VMWare). The New Zealand Data Head node is connected to the high speed (100 Gbps) network ring circuit courtesy of the Research and Education Advanced Network New Zealand (REANNZ), with the additional nodes at remote physical sites connected via 10 Gbps fibre. We use real Australian Long Baseline Array (LBA) observational data from 6 radio telescopes in Australia, South Africa and New Zealand (15 baselines) of 1.5 hours in duration making 8 TB to emulate data transfer from remote locations and to provide a meaningful benchmark dataset for correlation. Data was successfully transferred using bespoke UDT network transfer tools and correlated with the speed-up factor of 0.8 using DiFX software correlator. In partnership with the New Zealand office of Catalyst IT Ltd we have moved this environment into Catalyst Cloud and report on the first correlation of a VLBI Dataset in a true cloud environment.

Geodetic Space Weather Monitoring by means of Ionosphere Modelling

NASA Astrophysics Data System (ADS)

Schmidt, Michael

2017-04-01

The term space weather indicates physical processes and phenomena in space caused by radiation of energy mainly from the Sun. Manifestations of space weather are (1) variations of the Earth's magnetic field, (2) the polar lights in the northern and southern hemisphere, (3) variations within the ionosphere as part of the upper atmosphere characterized by the existence of free electrons and ions, (4) the solar wind, i.e. the permanent emission of electrons and photons, (5) the interplanetary magnetic field, and (6) electric currents, e.g. the van Allen radiation belt. It can be stated that ionosphere disturbances are often caused by so-called solar storms. A solar storm comprises solar events such as solar flares and coronal mass ejections (CMEs) which have different effects on the Earth. Solar flares may cause disturbances in positioning, navigation and communication. CMEs can effect severe disturbances and in extreme cases damages or even destructions of modern infrastructure. Examples are interruptions to satellite services including the global navigation satellite systems (GNSS), communication systems, Earth observation and imaging systems or a potential failure of power networks. Currently the measurements of solar satellite missions such as STEREO and SOHO are used to forecast solar events. Besides these measurements the Earth's ionosphere plays another key role in monitoring the space weather, because it responses to solar storms with an increase of the electron density. Space-geodetic observation techniques, such as terrestrial GNSS, satellite altimetry, space-borne GPS (radio occultation), DORIS and VLBI provide valuable global information about the state of the ionosphere. Additionally geodesy has a long history and large experience in developing and using sophisticated analysis and combination techniques as well as empirical and physical modelling approaches. Consequently, geodesy is predestinated for strongly supporting space weather monitoring via modelling the ionosphere and detecting and forecasting its disturbances. At present a couple of nations, such as the US, UK, Japan, Canada and China, are taken the threats from extreme space weather events seriously and support the development of observing strategies and fundamental research. However, (extreme) space weather events are in all their consequences on the modern highly technologized society, causative global problems which have to be treated globally and not regionally or even nationally. Consequently, space weather monitoring must include (1) all space-geodetic observation techniques and (2) geodetic evaluation methods such as data combination, real-time modelling and forecast. In other words, geodetic space weather monitoring comprises the basic ideas of GGOS and will provide products such as forecasts of severe solar events in order to initiate necessary activities to protect the infrastructure of modern society.

The new DMT SAFEGUARD low-cost GNSS measuring system and its application in the field of geotechnical deformation and movement monitoring

NASA Astrophysics Data System (ADS)

Schröder, Daniel

2017-04-01

In the recent years an increasing awareness of geodetic measurement systems and their application for monitoring projects is clearly visible. With geodetic sensors it is possible to detect safety-related changes at monitoring objects with high temporal density, high accuracy and in a very reliable manner. Quality acquisitions, processing and storage of monitoring data as well as a professional on-site implementation are the most important requirements and challenges to contemporary systems in civil engineering, mining as well as oil and gas production. Monitoring measures provide important input for early warning, alarm, protection and verification of potential hazardous environments and therefore the risk management applied to projects have a significant influence. The implementation has to follow an optimization process incorporating necessary accuracy, reliability and economic efficiency. From the economical point of view the costs per observation point are crucial for most monitoring projects. Keeping in mind that the costs of classical high-end GNSS stations with a geodetic dual-frequency receiver is within the range of several 10,000 euro. Large monitoring networks with a high number of simultaneously observed points are very expensive and therefore eventually have to be cut back, substituted by compromising methods or totally withdrawn. A further development in the area of GNSS receivers could reduce this disadvantage. Within the last few years single-frequency receivers that record L1-signals of GPS/GLONASS and offer sub-centimeter positioning accuracies are increasingly offered on the market. The accuracy of GNSS measurements depends on many factors as the hardware itself as well as on external influences related to the measurement principals. The external influences can be strongly reduced or eliminated by appropriate measuring and processing methods. For a reliable monitoring system it is necessary that the results are comparable and consistent for each epoch. Based on these requirements DMT has developed the new DMT SAFEGUARD GNSS. In this article the latest developments in the field of low-cost GNSS are shown by different examples from industry and authorities. By means of a detailed accuracy study the DMT SAFEGUARD GNSS system applicability will be demonstrated. The study shows possibilities to detect coordinate shifts on sub centimeter level by using suitable data processing approaches and permanent network solutions. In addition to the DMT SAFEGUARD GNSS system this article illustrates the combination with further relevant sensors to integrated multisensorial networks. Such networks include geodetic data, geophysical data, geotechnical data, video, audio etc. For the central integration of all sensor types DMT has developed a web-based monitoring system - DMT SAFEGUARD which offers individual customizing, sophisticated analysis tools as well as comprehensive reporting options.

A highly accurate absolute gravimetric network for Albania, Kosovo and Montenegro

NASA Astrophysics Data System (ADS)

Ullrich, Christian; Ruess, Diethard; Butta, Hubert; Qirko, Kristaq; Pavicevic, Bozidar; Murat, Meha

2016-04-01

The objective of this project is to establish a basic gravity network in Albania, Kosovo and Montenegro to enable further investigations in geodetic and geophysical issues. Therefore the first time in history absolute gravity measurements were performed in these countries. The Norwegian mapping authority Kartverket is assisting the national mapping authorities in Kosovo (KCA) (Kosovo Cadastral Agency - Agjencia Kadastrale e Kosovës), Albania (ASIG) (Autoriteti Shtetëror i Informacionit Gjeohapësinor) and in Montenegro (REA) (Real Estate Administration of Montenegro - Uprava za nekretnine Crne Gore) in improving the geodetic frameworks. The gravity measurements are funded by Kartverket. The absolute gravimetric measurements were performed from BEV (Federal Office of Metrology and Surveying) with the absolute gravimeter FG5-242. As a national metrology institute (NMI) the Metrology Service of the BEV maintains the national standards for the realisation of the legal units of measurement and ensures their international equivalence and recognition. Laser and clock of the absolute gravimeter were calibrated before and after the measurements. The absolute gravimetric survey was carried out from September to October 2015. Finally all 8 scheduled stations were successfully measured: there are three stations located in Montenegro, two stations in Kosovo and three stations in Albania. The stations are distributed over the countries to establish a gravity network for each country. The vertical gradients were measured at all 8 stations with the relative gravimeter Scintrex CG5. The high class quality of some absolute gravity stations can be used for gravity monitoring activities in future. The measurement uncertainties of the absolute gravity measurements range around 2.5 micro Gal at all stations (1 microgal = 10-8 m/s2). In Montenegro the large gravity difference of 200 MilliGal between station Zabljak and Podgorica can be even used for calibration of relative gravimeters. The complete basic gravimetric network of these countries will be tied to these absolute stations. In this presentation all the stations and results will be presented in detail and some special results analysed.

Status of NGS CORS Network and Its Contribution to the GGOS Infrastructure

NASA Astrophysics Data System (ADS)

Choi, K. K.; Haw, D.; Sun, L.

2017-12-01

Recent advancement of Satellite Geodesy techniques can now contribute to the global frame realization needed to improve worldwide accuracies. These techniques rely on coordinates computed using continuously observed GPS data and corresponding satellite orbits. The GPS-based reference system continues to depend on the physical stability of a ground-based network of points as the primary foundation for these observations. NOAA's National Geodetic Survey (NGS) has been operating Continuously Operating Reference Stations (CORS) to provide direct access to the National Spatial Reference System (NSRS). By virtue of NGS' scientific reputation and leadership in national and international geospatial issues, NGS has determined to increase its participation in the maintenance of the U.S. component of the global GPS tracking network in order to realize a long-term stable national terrestrial reference frame. NGS can do so by leveraging its national leadership role coupled with NGS' scientific expertise, in designating and upgrading a subset of the current tracking network for this purpose. This subset of stations must have the highest operational standards to serve the dual functions: being the U.S. contribution to the international frame, along with providing the link to the national datum. These stations deserve special attention to ensure that the highest possible levels of quality and stability are maintained. To meet this need, NGS is working with the international scientific groups to add and designate these reference stations based on scientific merit such as: colocation with other geodetic techniques, geographic area, and monumentation stability.

50 years of Global Seismic Observations

NASA Astrophysics Data System (ADS)

Anderson, K. R.; Butler, R.; Berger, J.; Davis, P.; Derr, J.; Gee, L.; Hutt, C. R.; Leith, W. S.; Park, J. J.

2007-12-01

Seismological recordings have been made on Earth for hundreds of years in some form or another, however, global monitoring of earthquakes only began in the 1890's when John Milne created 40 seismic observatories to measure the waves from these events. Shortly after the International Geophysical Year (IGY), a concerted effort was made to establish and maintain a more modern standardized seismic network on the global scale. In the early 1960's, the World-Wide Standardized Seismograph Network (WWSSN) was established through funding from the Advanced Research Projects Agency (ARPA) and was installed and maintained by the USGS's Albuquerque Seismological Laboratory (then a part of the US Coast and Geodetic Survey). This network of identical seismic instruments consisted of 120 stations in 60 countries. Although the network was motivated by nuclear test monitoring, the WWSSN facilitated numerous advances in observational seismology. From the IGY to the present, the network has been upgraded (High-Gain Long-Period Seismograph Network, Seismic Research Observatories, Digital WWSSN, Global Telemetered Seismograph Network, etc.) and expanded (International Deployment of Accelerometers, US National Seismic Network, China Digital Seismograph Network, Joint Seismic Project, etc.), bringing the modern day Global Seismographic Network (GSN) to a current state of approximately 150 stations. The GSN consists of state-of-the-art very broadband seismic transducers, continuous power and communications, and ancillary sensors including geodetic, geomagnetic, microbarographic, meteorological and other related instrumentation. Beyond the GSN, the system of global network observatories includes contributions from other international partners (e.g., GEOSCOPE, GEOFON, MEDNET, F-Net, CTBTO), forming an even larger backbone of permanent seismological observatories as a part of the International Federation of Digital Seismograph Networks. 50 years of seismic network operations have provided valuable data for earth science research. Developments in communications and other technological advances have expanded the role of the GSN in rapid earthquake analysis, tsunami warning, and nuclear test monitoring. With such long-term observations, scientists are now getting a glimpse of Earth structure changes on human time scales, such as the rotation of the inner core, as well as views into climate processes. Continued observations for the next 50 years will enhance our image of the Earth and its processes.

Time Biases in laser ranging measurements; impacts on geodetic products (Reference Frame and Orbitography)

NASA Astrophysics Data System (ADS)

Belli, A.; Exertier, P.; Lemoine, F. G.; Chinn, D. S.; Zelensky, N. P.

2017-12-01

The GGOS objectives are to maintain a geodetic network with an accuracy of 1 mm and a stability of 0.1 mm per year. For years, the laser ranging technique, which provide very accurate absolute distances to geodetic targets enable to determine the scale factor as well as coordinates of the geocenter. In order to achieve this goal, systematic errors appearing in the laser ranging measurements must be considered and solved. In addition to Range Bias (RB), which is the primary source of uncertainty of the technique, Time Bias (TB) has been recently detected by using the Time Transfer by Laser Link (T2L2) space instrument capability on-board the satellite Jason-2. Instead of determining TB through the precise orbit determination that is applied to commonly used geodetic targets like LAGEOS to estimate global geodetic products, we have developed, independently, a dedicated method to transfer time between remote satellite laser ranging stations. As a result, the evolving clock phase shift to UTC of around 30 stations has been determined under the form of time series of time bias per station from 2008 to 2016 with an accuracy of 3-4 ns. It demonstrated the difficulty, in terms of Time & Frequency used technologies, to locally maintain accuracy and long term stability at least in the range of 100 ns that is the current requirement for time measurements (UTC) for the laser ranging technique. Because some laser ranging stations oftently exceed this limit (from 100 ns to a few μs) we have been studying these effects first on the precision orbit determination itself, second on the station positioning. We discuss the impact of TB on LAGEOS and Jason-2 orbits, which appears to affect the along-track component essentially. We also investigate the role of TB in global geodetic parameters as the station coordinates. Finally, we propose to provide the community with time series of time bias of laser ranging stations, under the form of a data- handling-file in order to be included in each orbit determination process that is using laser ranging data since 2008.

Evaluation of Integration Degree of the ASG-EUPOS Polish Reference Networks With Ukrainian GeoTerrace Network Stations in the Border Area

NASA Astrophysics Data System (ADS)

Siejka, Zbigniew

2017-09-01

GNSS systems are currently the basic tools for determination of the highest precision station coordinates (e.g. basic control network stations or stations used in the networks for geodynamic studies) as well as for land, maritime and air navigation. All of these tasks are carried out using active, large scale, satellite geodetic networks which are complex, intelligent teleinformatic systems offering post processing services along with corrections delivered in real-time for kinematic measurements. Many countries in the world, also in Europe, have built their own multifunctional networks and enhance them with their own GNSS augmentation systems. Nowadays however, in the era of international integration, there is a necessity to consider collective actions in order to build a unified system, covering e.g. the whole Europe or at least some of its regions. Such actions have already been undertaken in many regions of the world. In Europe such an example is the development for EUPOS which consists of active national networks built in central eastern European countries. So far experience and research show, that the critical areas for connecting these networks are border areas, in which the positioning accuracy decreases (Krzeszowski and Bosy, 2011). This study attempts to evaluate the border area compatibility of Polish ASG-EUPOS (European Position Determination System) reference stations and Ukrainian GeoTerrace system reference stations in the context of their future incorporation into the EUPOS. The two networks analyzed in work feature similar hardware parameters. In the ASG-EUPOS reference stations network, during the analyzed period, 2 stations (WLDW and CHEL) used only one system (GPS), while, in the GeoTerrace network, all the stations were equipped with both GPS and GLONASS receivers. The ASG EUPOS reference station network (95.6%) has its average completeness greater by about 6% when compared to the GeoTerrace network (89.8%).

Automated and continual determination of radio telescope reference points with sub-mm accuracy: results from a campaign at the Onsala Space Observatory

NASA Astrophysics Data System (ADS)

Lösler, Michael; Haas, Rüdiger; Eschelbach, Cornelia

2013-08-01

The Global Geodetic Observing System (GGOS) requires sub-mm accuracy, automated and continual determinations of the so-called local tie vectors at co-location stations. Co-location stations host instrumentation for several space geodetic techniques and the local tie surveys involve the relative geometry of the reference points of these instruments. Thus, these reference points need to be determined in a common coordinate system, which is a particular challenge for rotating equipment like radio telescopes for geodetic Very Long Baseline Interferometry. In this work we describe a concept to achieve automated and continual determinations of radio telescope reference points with sub-mm accuracy. We developed a monitoring system, including Java-based sensor communication for automated surveys, network adjustment and further data analysis. This monitoring system was tested during a monitoring campaign performed at the Onsala Space Observatory in the summer of 2012. The results obtained in this campaign show that it is possible to perform automated determination of a radio telescope reference point during normal operations of the telescope. Accuracies on the sub-mm level can be achieved, and continual determinations can be realized by repeated determinations and recursive estimation methods.

Time and position accuracy using codeless GPS

NASA Technical Reports Server (NTRS)

Dunn, C. E.; Jefferson, D. C.; Lichten, S. M.; Thomas, J. B.; Vigue, Y.; Young, L. E.

1994-01-01

The Global Positioning System has allowed scientists and engineers to make measurements having accuracy far beyond the original 15 meter goal of the system. Using global networks of P-Code capable receivers and extensive post-processing, geodesists have achieved baseline precision of a few parts per billion, and clock offsets have been measured at the nanosecond level over intercontinental distances. A cloud hangs over this picture, however. The Department of Defense plans to encrypt the P-Code (called Anti-Spoofing, or AS) in the fall of 1993. After this event, geodetic and time measurements will have to be made using codeless GPS receivers. However, there appears to be a silver lining to the cloud. In response to the anticipated encryption of the P-Code, the geodetic and GPS receiver community has developed some remarkably effective means of coping with AS without classified information. We will discuss various codeless techniques currently available and the data noise resulting from each. We will review some geodetic results obtained using only codeless data, and discuss the implications for time measurements. Finally, we will present the status of GPS research at JPL in relation to codeless clock measurements.

Geoid modeling in Mexico and the collaboration with Central America and the Caribbean.

NASA Astrophysics Data System (ADS)

Avalos, D.; Gomez, R.

2012-12-01

The model of geoidal heights for Mexico, named GGM10, is presented as a geodetic tool to support vertical positioning in the context of regional height system unification. It is a purely gravimetric solution computed by the Stokes-Helmert technique in resolution of 2.5 arc minutes. This product from the Instituto Nacional de Estadistica y Geografia (INEGI) is released together with a series of 10 gravimetric models which add to the improvements in description of the gravity field. In the recent years, the INEGI joined the initiative of the U.S. National Geodetic Survey and the Canada's Geodetic Survey Division to promote the regional height system unification. In an effort to further improve the compatibility among national geoid models in the region, the INEGI has begun to champion a network of specialists that includes national representatives from Central America and the Caribbean. Through the opening of opportunities for training and more direct access to international agreements and discussions, the tropical region is gaining participation. Now a significantly increased number of countries is pushing for a future North and Central American geoid-based vertical datum as support of height system unification.eoidal height in Mexico, mapped from the model GGM10.

Generation, estimation, utilization, availability and compatibility aspects of geodetic and meteorological data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luetzow, H.B.v.

1983-08-01

Following an introduction, the paper discusses in section 2 the collection or generation of final geodetic data from conventional surveys, satellite observations, satellite altimetry, the Global Positioning System, and moving base gravity gradiometers. Section 3 covers data utilization and accuracy aspects including gravity programmed inertial positioning and subterraneous mass detection. Section 4 addresses the usefulness and limitation of the collocation method of physical geodesy. Section 5 is concerned with the computation of classical climatological data. In section 6, meteorological data assimilation is considered. Section 7 deals with correlated aspects of initial data generation with emphasis on initial wind field determination,more » parameterized and classical hydrostatic prediction models, non-hydrostatic prediction, computational networks, and computer capacity. The paper concludes that geodetic and meteorological data are expected to become increasingly more diversified and voluminous both regionally and globally, that its general availability will be more or less restricted for some time to come, that its quality and quantity are subject to change, and that meteorological data generation, accuracy and density have to be considered in conjunction with advanced as well as cost-effective numerical weather prediction models and associated computational efforts.« less

Seafloor Geodetic Monitoring of the Central Andean Subduction Zone: The Geosea Array

NASA Astrophysics Data System (ADS)

Kopp, H.; Lange, D.; Contreras Reyes, E.; Behrmann, J. H.; McGuire, J. J.; Flueh, E. R.

2014-12-01

Seafloor geodesy has been identified as one of the central tools in marine geosciences to monitor seafloor deformation at high resolution. To quantify strain accumulation and assess the resultant hazard potential we urgently need systems to resolve seafloor crustal deformation. The GeoSEA (Geodetic Earthquake Observatory on the Seafloor) array consists of a seafloor transponder network comprising a total of 35 units and a wave glider acting as a surface unit (GeoSURF) to ensure satellite correspondence, data transfer and monitor system health. For horizontal direct path measurements, the system utilizes acoustic ranging techniques with a ranging precision better than 15 mm and long term stability over 2 km distance. Vertical motion is obtained from pressure gauges. Integrated inclinometers monitor station settlement in two horizontal directions. Travel time between instruments and the local water sound velocity will be recorded autonomously subsea without system or human intervention for up to 3.5 years. Data from the autonomous network on the seafloor can be retrieved via the integrated high-speed acoustic telemetry link without recovering the seafloor units. In late 2015 GeoSEA will be installed on the Iquique segment of the South America - Nazca convergent plate boundary to monitor crustal deformation. The Iquique seismic gap experienced the 2014 Mw 8.1 Pisagua earthquake, which apparently occurred within a local locking minimum. It is thus crucial to better resolve resolve strain in the forearc between the mainland and the trench in order to improve our understanding of forearc deformation required for hazard assessment. Mobile autonomous seafloor arrays for continuous measurement of active seafloor deformation in hazard zones have the potential to lead to transformative discoveries of plate boundary/fault zone tectonic processes and address a novel element of marine geophysical research.

Polish Geophysical Solid Earth Infrastructure Contributing to EPOS

NASA Astrophysics Data System (ADS)

Debski, W.; Mutke, G.; Suchcicki, J.; Jozwiak, W.; Wiejacz, P.; Trojanowski, J.

2012-04-01

In this poster we present the current state of the main polish solid-earth-orientated infrastructures and shortly described history of their development, current state, and some plans for their future development. The presen- tation concentrates only on the classical infrastructure leaving aside for the while the the geodetic-orientated infrastructure, like GPS network and the GPS processing data centers, gravimetric infrastructure and others of this type. Polish broadband seismic infrastructure consists of 7 permanent broadband stations incorporated into the VEBSN initiative running at the polish territory and one operated in collaboration with NORSAR is settled at the Hornsund (Svalbard) polish polar station. All stations are equipped with STS-2 seismometers and polish MK-6 seismic stations providing 120 dB dynamics 100Hz sampling and data transmission in a real time to processing center. Besides this permanent broadband seismic network (PLSN) the Central Institute of Mining is running the permanent regional, short period network at the Upper Silesia area dedicated to the detailed monitoring of seismicity induced by the black coal mining activity in this area. The network consists of As the mining activity is the main source of seismicity in Poland also all mines are running underground short period networks, like for example Rudna-Polkowice copper mine seismic network consisting of 64 underground located short period seimometers. In that area, especially around the Zelazny Most: the huge post-floating artificial lake the, IGF PAS is running the local seismic array consisting of 4 short period seismometers. Besides these permanent network IGF PAN is running the portable seismic network for detailed mapping a possible natural seismic activity in selected regions of Poland. Important contribution to classical geophysical observation in the electro-magnetic field are provided by three permanent geomagnetic observatories (one at Hornsund) and supporting set of 10 portable, high-accuracy magnetoteluric stations.

Aseismic Deformation Associated with an Earthquake Swarm in the Northern Apennines (Italy)

NASA Astrophysics Data System (ADS)

Gualandi, A.; Nichele, C.; Serpelloni, E.; Chiaraluce, L.; Anderlini, L.; Latorre, D.; Belardinelli, M. E.; Avouac, J. P.

2017-12-01

Analyzing the displacement time series from continuous GPS (cGPS) with an Independent Component Analysis (ICA) we detect a transient deformation signal that correlates both in space and time with a seismic swarm activity (maximum Mw = 3.69 ± 0.09) occurred in the hanging wall of the Altotiberina normal fault (Northern Apennines, Italy) in 2013-2014. The geodetic transient lasted ˜6 months and produced a NW-SE trending extension of ˜ 5.3 mm, consistent with the regional tectonic regime. The seismicity and the geodetic signal are consistent with slip on two splay faults in the ATF hanging wall. Comparing the seismic moment associated with the geodetic transient and the seismic events, we observe that seismicity accounts for only a fraction of the measured geodetic deformation. The combined seismic and aseismic slip decreased the Coulomb stress on the locked shallow portion of the ATF, while the transition region to the creeping section has been loaded.

Repeating Deep Very Low Frequency Earthquakes: An Evidence of Transition Zone between Brittle and Ductile Zone along Plate Boundary

NASA Astrophysics Data System (ADS)

Ishihara, Y.; Yamamoto, Y.; Arai, R.

2017-12-01

Recently slow or low frequency seismic and geodetic events are focused under recognition of important role in tectonic process. The most western region of Ryukyu trench, Yaeyama Islands, is very active area of these type events. It has semiannual-like slow slip (Heki et.al., 2008; Nishimura et.al.,2014) and very frequent shallow very low frequency earthquakes near trench zone (Ando et.al.,2012; Nakamura et.al.,2014). Arai et.al.(2016) identified clear reverse phase discontinuity along plate boundary by air-gun survey, suggesting existence of low velocity layer including fluid. The subducting fluid layer is considered to control slip characteristics. On the other hand, deep low frequency earthquake and tremor observed at south-western Honshu and Shikoku of Japan are not identified well due to lack of high-quality seismic network. A broadband seismic station(ISG/PS) of Pacific21 network is operating in last 20 years that locates on occurrence potential area of low frequency earthquake. We tried to review continuous broadband record, searching low frequency earthquakes. In pilot survey, we found three very low frequency seismic events which are dominant in less than 0.1Hz component and are not listed in earthquake catalogue. Source locates about 50km depth and at transition area between slow slip event and active area of general earthquake along plate boundary. To detect small and/or hidden very low frequency earthquake, we applied matched filter analysis to continuous three components waveform data using pre-reviewed seismogram as template signal. 12 events with high correlation are picked up in last 10 years. Most events have very similar waveform, which means characteristics of repeating deep very low frequency earthquake. The event history of very low frequency earthquake is not related with one of slow slip event in this region. In Yaeyama region, low frequency earthquake, general earthquake and slow slip event occur dividing in space and have apparent independent activity. Further 3D survey around plate boundary may take us important understanding of controlling feature of seismic and geodetic slip.

A Recommendation on SLR Ranging to Future Global Navigation Satellite Systems

NASA Astrophysics Data System (ADS)

Labrecque, J. L.; Miller, J. J.; Pearlman, M.

2008-12-01

The multi-agency US Geodetic Requirements Working Group has recommended that Satellite Laser Retro- reflectors be installed on GPS III satellites as a principal component of the Positioning, Navigation, and Timing mandate of the Global Positioning System. The Working Group, which includes NASA, NGA, NOAA, NRL, USGS, and the USNO, echoes the Global Geodetic Observing System recommendation that SLR retro- reflectors be installed on all GNSS satellites. It is further recommended that the retro-reflectors conform to and hopefully exceed the minimum standard of the International Laser Ranging Service for retro-reflector cross sections of 100 million square meters for the HEO GNSS satellites to insure sufficiently accurate ranging by the global network of satellite laser ranging systems. The objective of this recommendation is to contribute to the improvement in the International Terrestrial Reference Frame, and its derivative the WGS84 reference frame, through continuing improvements in the characterization of the GPS orbits and clocks. Another objective is to provide an independent means of assessing the interoperability and accuracy of the GNSS systems and regional augmentation systems. The ranging to GNSS-mounted retro-reflectors will constitute a significant new means of space-based collocation to constrain the tie between the GPS and SLR networks that constitute over 50% of the data from which the ITRF is derived. The recommendation for the installation of SLR retro-reflectors aboard future GPS satellites is one of a number of efforts aimed at improving the accuracy and stability of ITRF. These steps are being coordinated with and supportive of the efforts of the GGOS and its services such at the VLBI2010 initiative, developing a next generation geodetic network, near real-time GPS positioning and EOP determination, and numerous efforts in the improvement of geodetic algorithms for GPS, SLR, VLBI, DORIS, and the determination of the ITRF. If past is prologue, the requirements of accuracy placed upon GNSS systems will continue to evolve at a factor of ten per decade for the lifetime of the GPS III, extending to 2025 and beyond. Global societal priorities such as sea level change measurement already require a factor of ten or more improvement in the accuracy and stability of the ITRF. Increasing accuracy requirements by civilian users for precision positioning and time keeping will certainly continue to grow at an exponential rate. The PNT accuracy of our GNSS systems will keep pace with these societal needs only if we equip the GNSS systems with the capability to identify and further reduce systematic errors.

Post-Seismic Crustal Deformation Following The 1999 Izmit Earthquake, Western Part Of North Anatolian Fault Zone, Turkey

NASA Astrophysics Data System (ADS)

Gurkan, O.; Ozener, H.

2004-12-01

The North Anatolian Fault is an about 1500 km long, extending from the Karliova to the North Aegean. Turkey is a natural laboratory with high tectonic activity caused by the relative motion of the Eurasian, Arabian and Anatolian plates. Western part of Turkey and its vicinity is a seismically active area. Since 1972 crustal deformation has been observed by various kinds of geodetic measurements in the area. Three GPS networks were installed in this region by Geodesy Department of Kandilli Observatory and Earthquake Research Institute( KOERI ) of Bogazici University: (1) Iznik Network, installed on the Iznik-Mekece fault zone, seismically low active part, (2) Sapanca Network, installed on the Izmit-Sapanca fault zone, seismically active part, (3) Akyazi Network, installed on their intersection area, the Mudurnu fault zone. First period observations were performed by using terrestrial methods in 1990 and these observations were repeated annually until 1993. Since 1994, GPS measurements have been carried out at the temporary and permanent points in the area and the crustal movements are being monitored. Horizontal deformations, which have not been detected by terrestrial methods, were determined from the results of GPS measurements. A M=7.4 earthquake hit Izmit, northern Turkey, on August 17, 1999. After this earthquake many investigations have been started in the region. An international project has been performed with the collaboration of Massachussets Institute of Technology, Turkish General Command of Mapping, Istanbul Technical University, TUBITAK-Marmara Research Center and Geodesy Department of KOERI. Postseismic movements have been observed by the region-wide network. A GPS network including 49 well spread points in Marmara region was observed twice a year between 1999 and 2003 years. During these surveys, another network with 6 points has been formed by using 2 points from each 3 microgeodetic networks on NAFZ with appropriate coverage and geometry. These points have been connected by GPS observations to monitor the deformations. This expanded microgeodetic network has been occupied with Istanbul-Kandilli continuous GPS station (KANT). The objective of this paper is to present the post-seismic crustal deformation obtained from the GPS observations at the Western Part of the North Anatolian Fault (NAF) in Turkey.

Design and Implementation of a Modern Automatic Deformation Monitoring System

NASA Astrophysics Data System (ADS)

Engel, Philipp; Schweimler, Björn

2016-03-01

The deformation monitoring of structures and buildings is an important task field of modern engineering surveying, ensuring the standing and reliability of supervised objects over a long period. Several commercial hardware and software solutions for the realization of such monitoring measurements are available on the market. In addition to them, a research team at the University of Applied Sciences in Neubrandenburg (NUAS) is actively developing a software package for monitoring purposes in geodesy and geotechnics, which is distributed under an open source licence and free of charge. The task of managing an open source project is well-known in computer science, but it is fairly new in a geodetic context. This paper contributes to that issue by detailing applications, frameworks, and interfaces for the design and implementation of open hardware and software solutions for sensor control, sensor networks, and data management in automatic deformation monitoring. It will be discussed how the development effort of networked applications can be reduced by using free programming tools, cloud computing technologies, and rapid prototyping methods.

The Promise and Challenges of High Rate GNSS for Environmental Monitoring and Response

NASA Astrophysics Data System (ADS)

LaBrecque, John

2017-04-01

The decadal vision Global Geodetic Observing System recognizes the potential of high rate real time GNSS for environmental monitoring. The GGOS initiated a program to advance GNSS real time high rate measurements to augment seismic and other sensor systems for earthquake and tsunami early warning. High rate multi-GNSS networks can provide ionospheric tomography for the detection and tracking of land, ocean and atmospheric gravity waves that can provide coastal warning of tsunamis induced by earthquakes, volcanic eruptions, severe weather and other catastrophic events. NASA has collaborated on a microsatellite constellation of GPS receivers to measure ocean surface roughness to improve severe storm tracking and a equatorial system of GPS occultation receivers to measure ionospheric and atmospheric dynamics. Systems such as these will be significantly enhanced by the availability of a four fold increase in GNSS satellite systems with new and enhanced signal structures and by the densification of regional multi-GNSS networks. These new GNSS capabilities will rely upon improved and cost effective communications infrastructure for a network of coordinated real time analysis centers with input to national warning systems. Most important, the implementation of these new real time GNSS capabilities will rely upon the broad international support for the sharing of real time GNSS much as is done in weather and seismic observing systems and as supported by the Committee of Experts on UN Global Geodetic Information Management (UNGGIM).

Theoretical and Applied Research in the Field of Higher Geodesy Conducted in Rzeszow

NASA Astrophysics Data System (ADS)

Kadaj, Roman; Świętoń, Tomasz

2016-06-01

Important qualitative changes were taking place in polish geodesy in last few years. It was related to application of new techniques and technologies and to introduction of European reference frames in Poland. New reference stations network ASG-EUPOS, together with Internet services which helps in precise positioning was created. It allows to fast setting up precise hybrid networks. New, accurate satellite networks became the basis of new definitions in the field of reference systems. Simultaneously arise the need of new software, which enables to execute the geodetic works in new technical conditions. Authors had an opportunity to participate in mentioned undertakings, also under the aegis of GUGiK, by creation of methods, algorithms and necessary software tools. In this way the automatic postprocessing module (APPS) in POZGEO service, a part of ASG-EUPOS system came into being. It is an entirely polish product which works in Trimble environment. Universal software for transformation between PLETRF89, PL-ETRF2000, PULKOWO'42 reference systems as well as defined coordinate systems was created (TRANSPOL v. 2.06) and published as open product. An essential functional element of the program is the quasi-geoid model PL-geoid-2011, which has been elaborated by adjustment (calibration) of the global quasi-geoid model EGM2008 to 570 geodetic points (satellite-leveling points). Those and other studies are briefly described in this paper.

Combining various space geodetic techniques for regional modeling of ionospheric electron density over Iran

NASA Astrophysics Data System (ADS)

Zare, Saeed; Alizadeh, M. Mahdi; Schuh, Harald

2017-04-01

Ionosphere is a layer of the upper atmosphere, between the thermosphere and the exosphere, distinguished because it is ionized by solar radiation. As an important part of human living environment, ionosphere affects our modern society in many ways. International broadcasters use this medium to reflect radio signals back toward the Earth. Ionosphere provides long range capabilities for commercial ship-to-shore communications, for trans-oceanic aircraft links, and for military communication and surveillance systems. Space geodetic techniques have turned into a capable tool for studying the ionosphere in the last decades. Up to now, two dimensional (2-D) models of vertical TEC (VTEC) have been widely developed and used by different communities; however, due to the fact that these models provide information about the integral of the whole electron content along the vertical or slant ray path, these maps are not useful when information about the ionosphere at different altitude is required. The aim of this study is to develop three dimensional (3-D) regional model of electron density by using combination of various space geodetic techniques. B-Spline basis functions are used for longitude and latitude variations of the electron density and Chapman profile function for altitude variations. The National Cartographic Center of Iran (NCC) has established a network of one hundred GPS stations: The Iranian Permanent GPS Network for Geodynamics (IPGN). The main task of the GPS stations is to collect and store raw GPS data and send it to Tehran processing center on a daily basis for final processing. The required data for our investigation are ground based measurements of permanent GPS stations over Iran and radio occultation data from Formosat-3/Cosmic for region of interest. We expect to increase accuracy and reliability of final model by integrating different observation techniques.

Designing the Next Generation Global Geodetic Network for GGOS

NASA Astrophysics Data System (ADS)

Pavlis, Erricos C.; Kuzmicz-Cieslak, Magdalena; König, Daniel; MacMillan, Daniel S.

2014-05-01

The U.S. National Research Council report "Precise Geodetic Infrastructure: National Requirements for a Shared Resource" (2010) recommended that we 'make a long-term commitment to maintain the International Terrestrial Reference Frame (ITRF) to ensure its continuity and stability'. It further determined that to ensure this, a network of about ~30 globally distributed "core" observatories with state of the art equipment was necessary and should be deployed over the next decade or so. The findings were based on simulation studies using conceptual networks where Satellite Laser Ranging (SLR) and Very Long Baseline Interferometry (VLBI) equipment of the next generation quality were deployed and operated 24/7. Since then, GGOS—the Global Geodetic Observing System, has embarked in an international effort to organize this future network, soliciting contributions from around the world, through an open solicitation "Call for Proposals—CfP". After a critical number of proposals were received, the results were evaluated and a data base was established where the likely sites are ranked in terms of the available equipment, local environment and weather, probability of completion and the relevant date, etc. The renewal process is expected to evolve smoothly over many years, from the current (legacy) state to the next generation ("GGOS-class") equipment. In order to design the optimal distribution of the proposed sites and to determine any gaps in the final network, simulations have been called for again, only this time the site locations are identical to those listed in the compiled data base, and the equipment at each site is in accordance to what is described in the data base for each point in time. The main objective of the simulations addresses the quality of the ITRF product from a network we expect to have in place about five and ten years after the NRC report (2016/2020). A secondary but equally important simulation task is the study of trade-offs when deploying new sites, e.g. comparing possible alternatives from several proposed sites in a region, or the order in time of deployment of future sites so that the transition is seamless and the ITRF suffers no degradation. As a first step, the simulation process was validated against the prior realization of the ITRF, using simulated SLR, VLBI and GNSS information based on two years of real data contributing to ITRF. We present the results of these simulation studies and examine the likelihood that the designed networks will successfully meet the GGOS goal of 1 mm or better accuracy at epoch and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components of the ITRF.

A FLINN Station at Pinon Flat Observatory

NASA Technical Reports Server (NTRS)

Agnew, Duncan Carr; Wyatt, Frank

1997-01-01

The main objectives are: (1) To develop Pinon Flat Observatory (PFO) as a prototype 'integrated' FLINN station: one from which many types of data are collected, combined, and made available to the DOSE program to enhance studies of local and regional strains; (2) To develop the theoretical framework and methods to integrate the various types of auxiliary data which are to be collected by NASA at space-geodetic sites of the FLINN network, with the aim of learning as much as possible about the nature of earth deformation; (3) To develop procedures for the efficient and useful storage and retrieval of such auxiliary data so that they may be efficiently utilized by DOSE investigators; (4) To investigate the stability of ground monumentation now used in space-geodetic measurements, including the field testing of existing and new monument designs.

Reprocessing Multiyear GPS Data from Continuously Operating Reference Stations on Cloud Computing Platform

NASA Astrophysics Data System (ADS)

Yoon, S.

2016-12-01

To define geodetic reference frame using GPS data collected by Continuously Operating Reference Stations (CORS) network, historical GPS data needs to be reprocessed regularly. Reprocessing GPS data collected by upto 2000 CORS sites for the last two decades requires a lot of computational resource. At National Geodetic Survey (NGS), there has been one completed reprocessing in 2011, and currently, the second reprocessing is undergoing. For the first reprocessing effort, in-house computing resource was utilized. In the current second reprocessing effort, outsourced cloud computing platform is being utilized. In this presentation, the outline of data processing strategy at NGS is described as well as the effort to parallelize the data processing procedure in order to maximize the benefit of the cloud computing. The time and cost savings realized by utilizing cloud computing approach will also be discussed.

Geodetic measurement of deformation east of the San Andreas Fault in Central California

NASA Technical Reports Server (NTRS)

Sauber, Jeanne; Solomon, Sean C.; Lisowski, Michael

1988-01-01

The shear strain rates in the Diablo Range of California have been calculated, and the slip rate along the Calaveras and Paicines faults in Central California have been estimated, on the basis of triangulation and trilateration data from two geodetic networks located between the western edge of the Great Valley and the San Andreas Fault. The orientation of the principal compressive strain predicted from the azimuth of the major structures in the region is N 25 deg E, leading to an average shear strain value that corresponds to a relative shortening rate of 4.5 + or - 2.4 mm/yr. It is inferred that the measured strain is due to compression across the fold of this area. The hypothesized uniform, fault-normal compression within the Coast Ranges is not supported by these results.

Crustal movements in Europe observed with EUROPE and IVS-T2 VLBI networks

NASA Astrophysics Data System (ADS)

Zubko, N.; Poutanen, M.

2011-07-01

The comparative analysis of the EUROPE and IVS-T2 geodetic VLBI sessions has been performed. The main purpose of both campaigns is to observe and accurately determine the VLBI station coordinates and their time evolution. In this analysis our interest is to understand the influence of network configuration on the estimated parameters and, also, how much the results of these two campaigns are consistent. We have used the VieVS software developing at Vienna University of Technology to analyze the EUROPE and IVS-T2 sessions of 2002-2009. We have analyzed the difference of crustal movements obtained with these two networks and the effect of network configuration and station selection. The EPN (EUREF permanent GNSS Network) and IGS (International GNSS Service) networks can be used to compare the results.

Local effects of redundant terrestrial and GPS-based tie vectors in ITRF-like combinations

NASA Astrophysics Data System (ADS)

Abbondanza, Claudio; Altamimi, Zuheir; Sarti, Pierguido; Negusini, Monia; Vittuari, Luca

2009-11-01

Tie vectors (TVs) between co-located space geodetic instruments are essential for combining terrestrial reference frames (TRFs) realised using different techniques. They provide relative positioning between instrumental reference points (RPs) which are part of a global geodetic network such as the international terrestrial reference frame (ITRF). This paper gathers the set of very long baseline interferometry (VLBI)-global positioning system (GPS) local ties performed at the observatory of Medicina (Northern Italy) during the years 2001-2006 and discusses some important aspects related to the usage of co-location ties in the combinations of TRFs. Two measurement approaches of local survey are considered here: a GPS-based approach and a classical approach based on terrestrial observations (i.e. angles, distances and height differences). The behaviour of terrestrial local ties, which routinely join combinations of space geodetic solutions, is compared to that of GPS-based local ties. In particular, we have performed and analysed different combinations of satellite laser ranging (SLR), VLBI and GPS long term solutions in order to (i) evaluate the local effects of the insertion of the series of TVs computed at Medicina, (ii) investigate the consistency of GPS-based TVs with respect to space geodetic solutions, (iii) discuss the effects of an imprecise alignment of TVs from a local to a global reference frame. Results of ITRF-like combinations show that terrestrial TVs originate the smallest residuals in all the three components. In most cases, GPS-based TVs fit space geodetic solutions very well, especially in the horizontal components (N, E). On the contrary, the estimation of the VLBI RP Up component through GPS technique appears to be awkward, since the corresponding post fit residuals are considerably larger. Besides, combination tests including multi-temporal TVs display local effects of residual redistribution, when compared to those solutions where Medicina TVs are added one at a time. Finally, the combination of TRFs turns out to be sensitive to the orientation of the local tie into the global frame.

Transfer fault earthquake in compressionally reactivated back-arc failed rift: 1948 Fukui earthquake (M7.1), Japan

NASA Astrophysics Data System (ADS)

Ishiyama, Tatsuya; Kato, Naoko; Sato, Hiroshi; Koshiya, Shin

2017-04-01

Back-arc rift structures in many subduction zones are recognized as mechanically and thermally weak zones that possibly play important roles in strain accommodation at later post-rift stages within the overriding plates. In case of Miocene back-arc failed rift structures in the Sea of Japan in the Eurasian-Pacific subduction system, the mechanical contrasts between the crustal thrust wedges of the pre-rift continental crust and high velocity lower crust have fundamentally controlled the styles of post-rift, Quaternary active deformation (Ishiyama et al. 2016). In this study, we show a possibility that strike-slip M>7 devastating earthquakes in this region have been gregion enerated by reactivation of transfer faults highly oblique to the rift axes. The 1948 Fukui earthquake (M7.1), onshore shallow seismic event with a strike-slip faulting mechanism (Kanamori, 1973), resulted in more than 3,500 causalities and destructive damages on the infrastructures. While geophysical analyses on geodetic measurements based on leveling and triangulation networks clearly show coseismic left-lateral fault slip on a NNW striking vertical fault plane beneath the Fukui plain (Sagiya, 1999), no evidence for coseismic surface rupture has been identified based on both post-earthquake intensive fieldwork and recent reexamination of stereopair interpretations using 1/3,000 aerial photographs taken in 1948 (Togo et al., 2000). To find recognizable fault-related structures that deform Neogene basin fill sediments, we collected new 9.6-km-long high-resolution seismic reflection data across the geodetically estimated fault plane and adjacent subparallel active strike slip faults, using 925 offline recorders and Envirovib truck as a seismic source. A depth-converted section to 1.5 km depth contains discontinuous seismic reflectors correlated to Miocene volcaniclastic deposits and depression of the overlying Plio-Pleistocene sediments above the geodetically determined fault plane. We interpreted these structural features as negative flower structures related to the strike-slip fault activated during the 1948 seismic event. Locations of these strike-slip faults are consistent with Miocene transfer faults that offset syn- and post-rift sediments and underlying crustal wedges, suggesting that reactivation of transfer faults resulted in active strike-slip faulting including the 1948 seismic event. These findings demonstrate that not only rift-related normal faults but also transfer faults have strong structural inheritances and played essential roles on their active reactivation and seismicity during the post-rift stress regime.

Methodology for earthquake rupture rate estimates of fault networks: example for the western Corinth rift, Greece

NASA Astrophysics Data System (ADS)

Chartier, Thomas; Scotti, Oona; Lyon-Caen, Hélène; Boiselet, Aurélien

2017-10-01

Modeling the seismic potential of active faults is a fundamental step of probabilistic seismic hazard assessment (PSHA). An accurate estimation of the rate of earthquakes on the faults is necessary in order to obtain the probability of exceedance of a given ground motion. Most PSHA studies consider faults as independent structures and neglect the possibility of multiple faults or fault segments rupturing simultaneously (fault-to-fault, FtF, ruptures). The Uniform California Earthquake Rupture Forecast version 3 (UCERF-3) model takes into account this possibility by considering a system-level approach rather than an individual-fault-level approach using the geological, seismological and geodetical information to invert the earthquake rates. In many places of the world seismological and geodetical information along fault networks is often not well constrained. There is therefore a need to propose a methodology relying on geological information alone to compute earthquake rates of the faults in the network. In the proposed methodology, a simple distance criteria is used to define FtF ruptures and consider single faults or FtF ruptures as an aleatory uncertainty, similarly to UCERF-3. Rates of earthquakes on faults are then computed following two constraints: the magnitude frequency distribution (MFD) of earthquakes in the fault system as a whole must follow an a priori chosen shape and the rate of earthquakes on each fault is determined by the specific slip rate of each segment depending on the possible FtF ruptures. The modeled earthquake rates are then compared to the available independent data (geodetical, seismological and paleoseismological data) in order to weight different hypothesis explored in a logic tree.The methodology is tested on the western Corinth rift (WCR), Greece, where recent advancements have been made in the understanding of the geological slip rates of the complex network of normal faults which are accommodating the ˜ 15 mm yr-1 north-south extension. Modeling results show that geological, seismological and paleoseismological rates of earthquakes cannot be reconciled with only single-fault-rupture scenarios and require hypothesizing a large spectrum of possible FtF rupture sets. In order to fit the imposed regional Gutenberg-Richter (GR) MFD target, some of the slip along certain faults needs to be accommodated either with interseismic creep or as post-seismic processes. Furthermore, computed individual faults' MFDs differ depending on the position of each fault in the system and the possible FtF ruptures associated with the fault. Finally, a comparison of modeled earthquake rupture rates with those deduced from the regional and local earthquake catalog statistics and local paleoseismological data indicates a better fit with the FtF rupture set constructed with a distance criteria based on 5 km rather than 3 km, suggesting a high connectivity of faults in the WCR fault system.

A Strategic Independent Geodetic VLBI Network for Europe

NASA Astrophysics Data System (ADS)

Dale, Denise; Combrinck, Ludwig; de Witt, Alet

2014-12-01

Irregularities of the rotation of the Earth in space are described by the Earth Orientation Parameters (EOPs). An independent EOP network, applying the Very Long Baseline Interferometry (VLBI) technique and using the Vienna VLBI Software (VieVS), are strategically essential for Europe to minimize its reliance on foreign global support in terms of required infrastructure for the realization of such a network. The generation of independent EOPs is already achievable by countries such as the USA, the People's Republic of China, and the Russian Federation due to their large extent of land mass that allows for long baselines in both the North-South and East-West directions and thus allows for accurate determination of all EOPs. These three countries need not rely on foreign partnerships to generate EOPs, as they all have independent geodetic VLBI networks capable of determining EOPs for precise positioning, navigation, and satellite launch/orbital purposes. They also have or are developing independent Global Navigation Satellite Systems (GNSS) constellations; so does the European Union (EU). Accurate EOPs are essential for long-term orbital maintenance of GNSS constellations, leaving the EU GALILEO GNSS vulnerable and reliant on the three superpowers. Generation of accurate EOPs by Europe is not possible due to its much smaller land mass and thus smaller achievable baselines. Even though there are many radio telescopes spread across Europe, these are separated by relatively short distances. The proposed stations that will be used to investigate this independent EOP network for Europe are the WETTZELL radio telescope in Germany, two German owned radio telescopes, TIGOCONC in Concepción, Chile, and OHIGGINS in Antarctica, as well as the HartRAO radio telescope in South Africa.

Global Positioning System Bibliography

DTIC Science & Technology

1992-03-01

Nev., November, pp. 110-121. Chrzanowski, A. (1987). " Experiencias con GPS en mediciones de deformaciones." Presented at: Workshop on New Techniques...Material Placed in Open Waters Area 2 - Material Properties Related to Navigation and Dredging Area 3 - Dredge Plant Equipment and Systems Processes Area 4...Positioning System." Proceedings of the Second International Symposium on Problems Related to the Redefinintion of North American Geodetic Networks

Vertical-Deformation, Water-Level, Microgravity, Geodetic, Water-Chemistry, and Flow-Rate Data Collected During Injection, Storage, and Recovery Tests at Lancaster, Antelope Valley, California, September 1995 Through September 1998

DTIC Science & Technology

2002-01-01

63 Tiltmeter Network...71 34. Map showing locations of tiltmeters used to monitor the magnitude and direction of ground tilting associated with direct well injection...during cycle 2 at Lancaster, Antelope Valley, California .............................. 72 35. Photograph showing typical tiltmeter installation for

On the geodetic applications of simultaneous range-differencing to LAGEOS

NASA Technical Reports Server (NTRS)

Pablis, E. C.

1982-01-01

The possibility of improving the accuracy of geodetic results by use of simultaneously observed ranges to Lageos, in a differencing mode, from pairs of stations was studied. Simulation tests show that model errors can be effectively minimized by simultaneous range differencing (SRD) for a rather broad class of network satellite pass configurations. The methods of least squares approximation are compared with monomials and Chebyshev polynomials and the cubic spline interpolation. Analysis of three types of orbital biases (radial, along- and across track) shows that radial biases are the ones most efficiently minimized in the SRC mode. The degree to which the other two can be minimized depends on the type of parameters under estimation and the geometry of the problem. Sensitivity analyses of the SRD observation show that for baseline length estimations the most useful data are those collected in a direction parallel to the baseline and at a low elevation. Estimating individual baseline lengths with respect to an assumed but fixed orbit not only decreases the cost, but it further reduces the effects of model biases on the results as opposed to a network solution. Analogous results and conclusions are obtained for the estimates of the coordinates of the pole.

Regularized estimation of Euler pole parameters

NASA Astrophysics Data System (ADS)

Aktuğ, Bahadir; Yildirim, Ömer

2013-07-01

Euler vectors provide a unified framework to quantify the relative or absolute motions of tectonic plates through various geodetic and geophysical observations. With the advent of space geodesy, Euler parameters of several relatively small plates have been determined through the velocities derived from the space geodesy observations. However, the available data are usually insufficient in number and quality to estimate both the Euler vector components and the Euler pole parameters reliably. Since Euler vectors are defined globally in an Earth-centered Cartesian frame, estimation with the limited geographic coverage of the local/regional geodetic networks usually results in highly correlated vector components. In the case of estimating the Euler pole parameters directly, the situation is even worse, and the position of the Euler pole is nearly collinear with the magnitude of the rotation rate. In this study, a new method, which consists of an analytical derivation of the covariance matrix of the Euler vector in an ideal network configuration, is introduced and a regularized estimation method specifically tailored for estimating the Euler vector is presented. The results show that the proposed method outperforms the least squares estimation in terms of the mean squared error.

Congruence analysis of geodetic networks - hypothesis tests versus model selection by information criteria

NASA Astrophysics Data System (ADS)

Lehmann, Rüdiger; Lösler, Michael

2017-12-01

Geodetic deformation analysis can be interpreted as a model selection problem. The null model indicates that no deformation has occurred. It is opposed to a number of alternative models, which stipulate different deformation patterns. A common way to select the right model is the usage of a statistical hypothesis test. However, since we have to test a series of deformation patterns, this must be a multiple test. As an alternative solution for the test problem, we propose the p-value approach. Another approach arises from information theory. Here, the Akaike information criterion (AIC) or some alternative is used to select an appropriate model for a given set of observations. Both approaches are discussed and applied to two test scenarios: A synthetic levelling network and the Delft test data set. It is demonstrated that they work but behave differently, sometimes even producing different results. Hypothesis tests are well-established in geodesy, but may suffer from an unfavourable choice of the decision error rates. The multiple test also suffers from statistical dependencies between the test statistics, which are neglected. Both problems are overcome by applying information criterions like AIC.

On the impact of reducing global geophysical fluid model deformations in SLR data processing

NASA Astrophysics Data System (ADS)

Weigelt, Matthias; Thaller, Daniela

2016-04-01

Mass redistributions in the atmosphere, oceans and the continental hydrology cause elastic loading deformations of the Earth's crust and thus systematically influence Earth-bound observation systems such as VLBI, GNSS or SLR. Causing non-linear station variations, these loading deformations have a direct impact on the estimated station coordinates and an indirect impact on other parameters of global space-geodetic solutions, e.g. Earth orientation parameters, geocenter coordinates, satellite orbits or troposphere parameters. Generally, the impact can be mitigated by co-parameterisation or by reducing deformations derived from global geophysical fluid models. Here, we focus on the latter approach. A number of data sets modelling the (non-tidal) loading deformations are generated by various groups. They show regionally and locally significant differences and consequently the impact on the space-geodetic solutions heavily depends on the available network geometry. We present and discuss the differences between these models and choose SLR as the speace-geodetic technique of interest in order to discuss the impact of atmospheric, oceanic and hydrological loading on the parameters of space-geodetic solutions when correcting for the global geophysical fluid models at the observation level. Special emphasis is given to a consistent usage of models for geometric and gravimetric corrections during the data processing. We quantify the impact of the different deformation models on the station coordinates and discuss the improvement in the Earth orientation parameters and the geocenter motion. We also show that a significant reduction in the RMS of the station coordinates can be achieved depending on the model of choice.

New Geodetic Infrastructure for Australia: The NCRIS / AuScope Geospatial Component

NASA Astrophysics Data System (ADS)

Tregoning, P.; Watson, C. S.; Coleman, R.; Johnston, G.; Lovell, J.; Dickey, J.; Featherstone, W. E.; Rizos, C.; Higgins, M.; Priebbenow, R.

2009-12-01

In November 2006, the Australian Federal Government announced AUS15.8M in funding for geospatial research infrastructure through the National Collaborative Research Infrastructure Strategy (NCRIS). Funded within a broader capability area titled ‘Structure and Evolution of the Australian Continent’, NCRIS has provided a significant investment across Earth imaging, geochemistry, numerical simulation and modelling, the development of a virtual core library, and geospatial infrastructure. Known collectively as AuScope (www.auscope.org.au), this capability area has brought together Australian’s leading Earth scientists to decide upon the most pressing scientific issues and infrastructure needs for studying Earth systems and their impact on the Australian continent. Importantly and at the same time, the investment in geospatial infrastructure offers the opportunity to raise Australian geodetic science capability to the highest international level into the future. The geospatial component of AuScope builds onto the AUS15.8M of direct funding through the NCRIS process with significant in-kind and co-investment from universities and State/Territory and Federal government departments. The infrastructure to be acquired includes an FG5 absolute gravimeter, three gPhone relative gravimeters, three 12.1 m radio telescopes for geodetic VLBI, a continent-wide network of continuously operating geodetic quality GNSS receivers, a trial of a mobile SLR system and access to updated cluster computing facilities. We present an overview of the AuScope geospatial capability, review the current status of the infrastructure procurement and discuss some examples of the scientific research that will utilise the new geospatial infrastructure.

The integration of astro-geodetic data observed with ACSYS to the local geoid models Istanbul-Turkey

NASA Astrophysics Data System (ADS)

Halicioglu, Kerem; Ozludemir, M. Tevfik; Deniz, Rasim; Ozener, Haluk; Albayrak, Muge; Ulug, Rasit; Basoglu, Burak

2017-04-01

Astro-geodetic deflections of the vertical components provide accurate and valuable information of Earth's gravity filed. Conventional methods require considerable effort and time whereas new methods, namely digital zenith camera systems (DZCS), have been designed to eliminate drawbacks of the conventional methods, such as observer dependent errors, long observation times, and to improve the observation accuracy. The observation principle is based on capturing star images near zenithal direction to determine astronomical coordinates of the station point with the integration of CCD, telescope, tiltmeters, and GNSS devices. In Turkey a new DZCS have been designed and tested on control network located in Istanbul, of which the geoid height differences were known with the accuracy of ±3.5 cm. Astro-geodetic Camera System (ACSYS) was used to determine the deflections of the vertical components with an accuracy of ±0.1 - 0.3 arc seconds, and results were compared with geoid height differences using astronomical levelling procedure. The results have also been compared with the ones calculated from global geopotential models. In this study the recent results of the first digital zenith camera system of Turkey are presented and the future studies are introduced such as the current developments of the system including hardware and software upgrades as well as the new observation strategy of the ACSYS. We also discuss the contribution and integration of the astro-geodetic deflections of the vertical components to the geoid determination studies in the light of information of current ongoing projects being operated in Turkey.

Integration Of Low-Cost Single-Frequency GPS Stations Using 'Spider' Technology Within Existing Dual-Frequency GPS Network at Soufrière Hills Volcano, Montserrat (West Indies): Processing And Results

NASA Astrophysics Data System (ADS)

Pascal, K.; Palamartchouk, K.; Lahusen, R. G.; Young, K.; Voight, B.

2015-12-01

Twenty years ago, began the eruption of the explosive Soufrière Hills Volcano, dominating the southern part of the island of Montserrat, West Indies. Five phases of effusive activity have now occurred, characterized by dome building and collapse, causing numerous evacuations and the emigration of half of the population. Over the years, the volcano monitoring network has greatly expanded. The GPS network, started from few geodetic markers, now consists of 14 continuous dual frequency GPS stations, distributed on and around the edifice, where topography and vegetation allow. The continuous GPS time series have given invaluable insight into the volcano behavior, notably revealing deflation/inflation cycles corresponding to phases and pauses of effusive activity, respectively. In 2014, collaboration of the CALIPSO Project (Penn State; NSF) with the Montserrat Volcano Observatory enriched the GPS and seismic monitoring networks with six 'spider' stations. The 'spiders', developed by R. Lahusen at Cascades Volcano Observatory, are designed to be deployed easily in rough areas and combine a low cost seismic station and a L1-only GPS station. To date, three 'spiders' have been deployed on Soufrière Hills Volcano, the closest at ~1 km from the volcanic conduit, adjacent to a lava lobe on the dome. Here we present the details of GPS data processing in a network consisting of both dual and single frequency receivers ('spiders') using GAMIT/GLOBK software. Processing together single and dual frequency data allowed their representation in a common reference frame, and a meaningful geophysical interpretation of all the available data. We also present the 'spiders' time series along with the results from the rest of the network and examine if any significant deformation, correlating with other manifestations of volcanic activity, has been recorded by the 'spiders' since deployment. Our results demonstrate that low cost GNSS equipment can serve as valuable components in volcano deformation monitoring networks.

NASA directory of observation station locations, volume 1

NASA Technical Reports Server (NTRS)

1971-01-01

Geodetic information is presented for NASA tracking stations and observation stations in the NASA geodetic satellites program. A geodetic data sheet is provided for each station, giving the position of the station and describing briefly how it was established. Geodetic positions and geocentric coordinates of these stations are tabulated on local or major geodetic datums, and on selected world geodetic systems when available information permits.

GPS Measurements of Crustal Deformation in San Diego, CA: Results from fixed-height monument network and implications for the Inner Continental Borderlands

NASA Astrophysics Data System (ADS)

Singleton, D. M.; Agnew, D. C.; Maloney, J. M.; Rockwell, T. K.

2017-12-01

The Newport-Inglewood-Rose Canyon fault zone is the easternmost fault in a system of strike-slip faults that together make up the Inner Continental Borderlands (ICB), a region offshore of Southern California that is thought to accommodate 10-15% of the total plate boundary slip. However, slip on individual faults is difficult to measure because of the offshore location and limited availability of geologic indicators. With a 30-km onshore segment, the southern Rose Canyon fault zone (RCF) provides an opportunity to employ geodetic techniques to quantify the slip rate for a fault within the ICB. Space geodetic techniques have significantly enhanced our ability to quantify tectonic motion. With a best-estimated geologic slip rate of 1.5 ± 0.5 mm/yr, the RCF, as with other low slip-rate faults, is a challenge to traditional survey GPS techniques. Here we present the results from surveys of a GPS network first constructed in 1998 to determine motion across the RCF. This network has four sites, each site consisting of three to five closely spaced benchmarks that employ novel fixed-height centering with submillimeter repeatability so as to reduce noise associated with monument stability. Data collected from 1998 to 2017 shows millimeter-level monument stability and repeatability of the network. We present the results of velocity inversion for slip using data spanning 19 years across the Rose Canyon fault zone and discuss the implications for broader motion across the Inner Continental Borderlands.

The unrest of the San Miguel volcano (El Salvador, Central America): installation of the monitoring network and observed volcano-tectonic ground deformation

NASA Astrophysics Data System (ADS)

Bonforte, Alessandro; Hernandez, Douglas Antonio; Gutiérrez, Eduardo; Handal, Louis; Polío, Cecilia; Rapisarda, Salvatore; Scarlato, Piergiorgio

2016-08-01

On 29 December 2013, the Chaparrastique volcano in El Salvador, close to the town of San Miguel, erupted suddenly with explosive force, forming a column more than 9 km high and projecting ballistic projectiles as far as 3 km away. Pyroclastic density currents flowed to the north-northwest side of the volcano, while tephras were dispersed northwest and north-northeast. This sudden eruption prompted the local Ministry of Environment to request cooperation with Italian scientists in order to improve the monitoring of the volcano during this unrest. A joint force, made up of an Italian team from the Istituto Nazionale di Geofisica e Vulcanologia and a local team from the Ministerio de Medio Ambiente y Recursos Naturales, was organized to enhance the volcanological, geophysical and geochemical monitoring system to study the evolution of the phenomenon during the crisis. The joint team quickly installed a multiparametric mobile network comprising seismic, geodetic and geochemical sensors (designed to cover all the volcano flanks from the lowest to the highest possible altitudes) and a thermal camera. To simplify the logistics for a rapid installation and for security reasons, some sensors were colocated into multiparametric stations. Here, we describe the prompt design and installation of the geodetic monitoring network, the processing and results. The installation of a new ground deformation network can be considered an important result by itself, while the detection of some crucial deforming areas is very significant information, useful for dealing with future threats and for further studies on this poorly monitored volcano.

The unrest of S. Miguel volcano (El Salvador, CA): installation of the monitoring network and observed volcano-tectonic ground deformation

NASA Astrophysics Data System (ADS)

Bonforte, A.; Hernandez, D.; Gutiérrez, E.; Handal, L.; Polío, C.; Rapisarda, S.; Scarlato, P.

2015-10-01

On 29 December 2013, the Chaparrastique volcano in El Salvador, close to the town of S. Miguel, erupted suddenly with explosive force, forming a more than 9 km high column and projecting ballistic projectiles as far as 3 km away. Pyroclastic Density Currents flowed to the north-northwest side of the volcano, while tephras were dispersed northwest and north-northeast. This sudden eruption prompted the local Ministry of Environment to request cooperation with Italian scientists in order to improve the monitoring of the volcano during this unrest. A joint force made up of an Italian team from the Istituto Nazionale di Geofisica e Vulcanologia and a local team from the Ministerio de Medio Ambiente y Recursos Naturales was organized to enhance the volcanological, geophysical and geochemical monitoring system to study the evolution of the phenomenon during the crisis. The joint team quickly installed a multi-parametric mobile network comprising seismic, geodetic and geochemical sensors, designed to cover all the volcano flanks from the lowest to the highest possible altitudes, and a thermal camera. To simplify the logistics for a rapid installation and for security reasons, some sensors were co-located into multi-parametric stations. Here, we describe the prompt design and installation of the geodetic monitoring network, the processing and results. The installation of a new ground deformation network can be considered an important result by itself, while the detection of some crucial deforming areas is very significant information, useful for dealing with future threats and for further studies on this poorly monitored volcano.

NASA directory of observation station locations, volume 2

NASA Technical Reports Server (NTRS)

1971-01-01

The directory documents geodetic information for NASA tracking stations and observation stations in the NASA Geodetic Satellites Program, including stations participating in the National Geodetic Satellite Program. Station positions of these facilities are given on local or preferred major datums, and on the Modified Mercury Datum 1968. A geodetic data sheet is provided for each station, giving the position of the station and describing briefly how it was established. Geodetic positions and geocentric coordinates of these stations are tabulated on local or major geodetic datums, and on selected world geodetic systems when available information permits.

Seismic constraints on a large dyking event in Western Gulf of Aden

NASA Astrophysics Data System (ADS)

Ahmed, A.; Doubre, C.; Leroy, S.; Perrot, J.; Audin, L.; Rolandone, F.; Keir, D.; Al-Ganad, I.; Khanbari, K.; Mohamed, K.; Vergne, J.; Jacques, E.; Nercessian, A.

2012-04-01

In November 2010, a large number of events were recorded by the world seismic networks showing important activity occurring along the western part of the Aden Ridge. West of the Shulka El Sheik transform zone, events in this large seismic swarm (magnitudes above 5) occurred in a complex area, where the change of both the ridge direction and the bathymetry suggest the propagation of the ridge into a continental lithosphere and the influence of the thermal anomaly of the Afar Hot Spot. We combine several sets of data from permanent networks and temporary 3C broad stations installed after the beginning of the event along the southern and eastern coasts of Yemen and Djibouti respectively, we located more than 600 earthquakes with magnitudes ranging from 2.5 to 5.6 that occurred during the first months following the first event. The spatial distribution of the main seismicity reveals a very clear N115°-trending alignment, parallel to the mean direction of the en-echelon spreading segments that form the ridge at this longitude. Half of the events, which represent half of the total seismic energy released during the first months, are located in the central third section of the segment. Here several volcanic cones and recent lava flows observed from bathymetric and acoustic reflectivity data during the Tadjouraden cruise (Audin, 1999, Dauteuil et al., 2001) constitute the sea floor. In addition to this main activity, two small groups of events suggest the activiation of landslides into a large fan and the activity in a volcanic area 50 km due east from the main active zone. The time evolution of the seismicity shows several bursts of activity. Some of them are clearly related to sudden activities within the volcanic areas, when others exhibit horizontal migration of the events, with velocity around ~ 1 km/h. The time-space evolution of the seismicity clearly reveals the intrusion of dykes associated with magma propagation from the crustal magmatic centres into the rift zone.We use knowledge from spatial geodetic observations of rifting episodes in the regions: the Harrat Al-Shaqah event in 2009 (Arabia Souadia), the Tanzanian one in 2007, and the major Dabahu Manda Harraro rifting episode in Afar. Taking into account that the geodetic moment is one order of magnitude higher than the seismic moment during such events, the seismic activity of this event of the Aden ridge represents a major rifting episode certainly associated with the opening of the segment by dyking estimated to be higher than 10 m.

New insights on the seismic hazard in the Balkans inferred from GPS

NASA Astrophysics Data System (ADS)

D'Agostino, Nicola; Métois, Marianne; Avallone, Antonio; Chamot-Rooke, Nicolas

2014-05-01

The Balkans region sits at the transition between stable Eurasia and highly straining continental Eastern Mediterranean, resulting in a widespread seismicity and high seismic hazard. Because of intensive human and economic development over the last decades, the vulnerability has increased in the region faster than the progress in seismic hazard assessments. Opposite to the relatively good understanding of the seismicity in plate boundaries contexts, the seismic hazard is poorly known in the regions of distributed continental deformation like the Balkan region and is often underestimated (England and Jackson, 2011). Current seismic hazard assessments are based on the historical and instrumental catalogues. However, the completeness interval of the historical data bases may be below the average recurrence of individual seismogenic structures. In addition, relatively sparse seismological networks in the region and limited cross-border seismic data exchanges cast doubts in seismotectonic interpretation and challenge our understanding of seismic and geodynamic processes. This results in a inhomogeneous knowledge of the seismic hazard of the region to date. Geodetic measurements have the capability to contribute to seismic hazard by mapping the field of current active deformation and translating it into estimates of the seismogenic potential. With simple assumptions, measurements of crustal deformation can be translated in estimates of the average frequency and magnitude of the largest events and assessments of the aseismic deformation. GPS networks in the Balkans have been growing during the last few years mainly for civilian application (e.g. Cadastral plan, telecommunications), but opening new opportunities to quantify the present-day rates of crustal deformation. Here we present the initial results of GEOSAB (Geodetic Estimate of Strain Accumulation over Balkans), an AXA-Research-Fund supported project devoted to the estimation of crustal deformation and the associated seismic hazard of the Balkan region. We processed all the currently available data acquired on these new networks using the precise point positioning strategy of the Gipsy-Oasis software (Bertiger et al. 2010) and the daily ITF2008 transformation parameters (x-files) from JPL. Daily coordinates are obtained in a Eurasia-fix reference frame obtained using the strategy developed by Blewitt et al. (2012). Here we present this new velocity field combined with previously published data sets covering the Balkan Peninsula. This unusually dense picture of the current deformation, in particular in Slovenia and Serbia, enables us to derive a continuous map of the strain rate over the region using the approach of Haines and Holt (1993). We then derive the seismogenic potential of the region combining the geodetic strain rate and the available regional CMT moment tensor solutions. These maps bring new insights on areas of significant strain accumulation over the Balkan Peninsula and are a first step to better assess seismic hazard there.

Towards an Earthquake and Tsunami Early Warning in the Caribbean

NASA Astrophysics Data System (ADS)

Huerfano Moreno, V. A.; Vanacore, E. A.

2017-12-01

The Caribbean region (CR) has a documented history of large damaging earthquakes and tsunamis that have affected coastal areas, including the events of Jamaica in 1692, Virgin Islands in 1867, Puerto Rico in 1918, the Dominican Republic in 1946 and Haiti in 2010. There is clear evidence that tsunamis have been triggered by large earthquakes that deformed the ocean floor around the Caribbean Plate boundary. The CR is monitored jointly by national/regional/local seismic, geodetic and sea level networks. All monitoring institutions are participating in the UNESCO ICG/Caribe EWS, the purpose of this initiative is to minimize loss of life and destruction of property, and to mitigate against catastrophic economic impacts via promoting local research, real time (RT) earthquake, geodetic and sea level data sharing and improving warning capabilities and enhancing education and outreach strategies. Currently more than, 100 broad-band seismic, 65 sea levels and 50 GPS high rate stations are available in real or near real-time. These real-time streams are used by Local/Regional or Worldwide detection and warning institutions to provide earthquake source parameters in a timely manner. Currently, any Caribbean event detected to have a magnitude greater than 4.5 is evaluated, and sea level is measured, by the TWC for tsumanigenic potential. The regional cooperation is motivated both by research interests as well as geodetic, seismic and tsunami hazard monitoring and warning. It will allow the imaging of the tectonic structure of the Caribbean region to a high resolution which will consequently permit further understanding of the seismic source properties for moderate and large events and the application of this knowledge to procedures of civil protection. To reach its goals, the virtual network has been designed following the highest technical standards: BB sensors, 24 bits A/D converters with 140 dB dynamic range, real-time telemetry. Here we will discuss the state of the PR component of this virtual network as well as current advances in the imaging of the PR tectonic structure. The goal of this presentation is to describe the Puerto Rico Seismic Network (PRSN) system, including the real time earthquake and tsunami monitoring as well as the specific protocols used to broadcast earthquake/tsunami messages locally.

Ongoing Uplift Rates and Topography Across the Aleutian Forearc Region on Kodiak Island, Alaska.

NASA Astrophysics Data System (ADS)

Sauber, J. M.; Carver, G. A.

2002-12-01

The Kodiak Islands are part of a large subduction complex that comprises the eastern Aleutian forearc; the islands form the subaerial part of a broad topographic ridge that includes a Mesozoic-Cenozoic accretionary complex. To explore the relation between the ongoing subduction process, uplift rates and topographic characteristics, we have used a 30 m digital elevation map (DEM) derived from the Shuttle Radar Topography Mission (SRTM), an older 90 m DEM and ocean bathymetry. The topographic characteristics of Kodiak Island vary along strike and as a function of distance from the trench. From the northern to southern part of island, the distance from the 5800 m bathymetric contour (Aleutian Trench) and the eastern coast of Kodiak Island, as well as the width of the island, narrows by about 10% and probably reflects a steepening of the dip of the downgoing Pacific plate under the southern part of the island. The northern and central part of the island have similar topographic profiles as a function of distance from the trench; the highest peaks are located in the central part of the island. Although most of the island was glaciated during the last glacial maximum, the southwest portion of the island remained unglaciated; this region is distinctly less dissected. Preliminary uplift rates across the forearc region have been estimated from coastal marine terraces and short-term geodetic observations. Elevation changes over the last 103 - 104 years are being obtained from kinematic GPS observations across two sets of Holocene marine terrace sequences and from elevation measurements in northern Kodiak of an extensive late Pleistocene marine terrace (probably an oxygen isotope stage 5a, 120 - 130 ka). Initial measurements from the older terrace in northern Kodiak suggest an average uplift rate for the eastern side of Kodiak, above the down-dip end of the locked zone on the megathrust, to be about 1.2 mm/yr; on the western side of the island the uplift rate decreases by an order of magnitude. GPS observations of short-term uplift rates from a northern Kodiak geodetic network [Sauber et al.,2002] and a southern Kodiak geodetic network, (Katmai network of Savage et al., 1999), indicate similar uplift rates of 2-5 mm/yr along the eastern coast, 9-11 mm/yr near the city of Kodiak and 3-5 mm/yr along the western coast. These geodetically determined rates are an order of magnitude greater than the long-term rates derived from the raised coastal terraces. Numerical modeling of both sets of observations suggest that these short-term uplift rates are primarily due to interseismic strain associated with a shallow, locked, main thrust zone and down-dip, post-seismic processes following the 1964 earthquake, while the long-term rates include both interseismic and coseismic vertical motions over many seismic cycles. Except for the extreme eastern side of the island where active upper plate faults are present, uplift, as reflected by the elevation of the late Pleistocene marine terraces, decreases toward the west at a relatively uniform rate over long trench-normal distances. The region of highest short-term uplift does correspond to the region of highest topography. However, the elevation of the marine terraces on the eastern margin of the island indicate late Quaternary faulting and folding produce localized areas of anomalously high rates of uplift.

An Overview of Seismic Observations Along the Pacific Margin of South America: Opportunities for the SZ4D Initiative

NASA Astrophysics Data System (ADS)

Woodward, R.; Frassetto, A.; Meltzer, A.

2017-12-01

The recent SZ4D Initiative community vision document recognizes the potential to focus community resources on studying subduction processes along, for example, the Pacific margin of South America. Preexisting geophysical infrastructure can play a vital role in establishing such new observational capabilities. For example, an SZ4D backbone observing capability could be established in South America by leveraging existing stations in the region. Such relevant existing seismic and geodetic stations, operated as part of local or national networks in South America, have been identified as a result of recent international collaborations with IRIS and others. Here we discuss the concept and experience of leveraging existing infrastructure in major new observational programs, outline the state of geophysical networks in South America (emphasizing current seismic networks but also looking back on historical temporary deployments), and provide an overview of potential scientific targets in the Americas that encompass a sampling of recently produced research results and datasets. Additionally, we reflect on strategies for establishing meaningful collaborations across South America and elsewhere, an aspect that will be critical to the international partnerships, and associated capacity building, needed for an internationally inclusive and collaborative SZ4D activity.

Deep magma accumulation at Nyamulagira volcano in 2011 detected by GNSS observations

NASA Astrophysics Data System (ADS)

Ji, Kang Hyeun; Stamps, D. Sarah; Geirsson, Halldor; Mashagiro, Niche; Syauswa, Muhindo; Kafudu, Benjamin; Subira, Josué; d'Oreye, Nicolas

2017-10-01

People in the area of the Virunga Mountains, along the borders of the Democratic Republic of Congo, Rwanda, and Uganda, are at very high natural risk due to active volcanism. A Global Navigation Satellite System (GNSS) network, KivuGNet (Kivu Geodetic Network), has operated since 2009 for monitoring and research of the deformation of Nyamulagira and Nyiragongo volcanoes as well as tectonic deformation in the region. We detected an inflationary signal from the position time-series observed in the network using our detection method, which is a combination of Kalman filtering and principal component analysis. The inflation event began in October 2010 and lasted for about 6 months prior to the 2011-2012 eruption at Nyamulagira volcano. The pre-eruptive inflationary signal is much weaker than the co-eruptive signal, but our method successfully detected the signal. The maximum horizontal and vertical displacements observed are ∼9 mm and ∼5 mm, respectively. A Mogi point source at a depth >10 km can explain the displacement field. This suggests that a relatively deep source for the magma chamber generated the inflationary signal. The deep reservoir that is the focus of this study may feed a shallower magma chamber, which is the likely source of the 2011-2012 eruption. Continuous monitoring of the volcanic activity is essential for understanding the eruption cycle and assessing potential volcanic hazards.

Weighted triangulation adjustment

USGS Publications Warehouse

Anderson, Walter L.

1969-01-01

The variation of coordinates method is employed to perform a weighted least squares adjustment of horizontal survey networks. Geodetic coordinates are required for each fixed and adjustable station. A preliminary inverse geodetic position computation is made for each observed line. Weights associated with each observed equation for direction, azimuth, and distance are applied in the formation of the normal equations in-the least squares adjustment. The number of normal equations that may be solved is twice the number of new stations and less than 150. When the normal equations are solved, shifts are produced at adjustable stations. Previously computed correction factors are applied to the shifts and a most probable geodetic position is found for each adjustable station. Pinal azimuths and distances are computed. These may be written onto magnetic tape for subsequent computation of state plane or grid coordinates. Input consists of punch cards containing project identification, program options, and position and observation information. Results listed include preliminary and final positions, residuals, observation equations, solution of the normal equations showing magnitudes of shifts, and a plot of each adjusted and fixed station. During processing, data sets containing irrecoverable errors are rejected and the type of error is listed. The computer resumes processing of additional data sets.. Other conditions cause warning-errors to be issued, and processing continues with the current data set.

A global positioning measurement system for regional geodesy in the caribbean

NASA Astrophysics Data System (ADS)

Renzetti, N. A.

1986-11-01

Low cost, portable receivers using signals from satellites of the Global Positioning System (GPS) will enable precision geodetic observations to be made on a large scale. A number of important geophysical questions relating to plate-motion kinematics and dynamics can be addressed with this measurement capability. We describe a plan to design and validate a GPS-based geodetic system, and to demonstrate its capability in California, Mexico and the Caribbean region. The Caribbean program is a prototype for a number of regional geodetic networks to be globally distributed. In 1985, efforts will be concentrated on understanding and minimizing error sources. Two dominant sources of error are uncertainties in the orbit ephemeris of the GPS satellites, and uncertainties in the correction for signal delay due to variable tropospheric water vapor. Orbit ephemeris uncertainties can be minimized by performing simultaneous satellite observations with GPS receivers at known (fiducial) points. Water vapor corrections can be made by performing simultaneous line-of-sight measurements of integrated water vapor content with ground-based water vapor radiometers. Specific experiments to validate both concepts are outlined. Caribbean measurements will begin in late 1985 or early 1986. Key areas of measurement are the northern strike-slip boundary, and the western convergent boundary. Specific measurement plans in both regions are described.

NKG201xGIA - first results for a new model of glacial isostatic adjustment in Fennoscandia

NASA Astrophysics Data System (ADS)

Steffen, Holger; Barletta, Valentina; Kollo, Karin; Milne, Glenn A.; Nordman, Maaria; Olsson, Per-Anders; Simpson, Matthew J. R.; Tarasov, Lev; Ågren, Jonas

2016-04-01

Glacial isostatic adjustment (GIA) is a dominant process in northern Europe, which is observed with several geodetic and geophysical methods. The observed land uplift due to this process amounts to about 1 cm/year in the northern Gulf of Bothnia. GIA affects the establishment and maintenance of reliable geodetic and gravimetric reference networks in the Nordic countries. To support a high level of accuracy in the determination of position, adequate corrections have to be applied with dedicated models. Currently, there are efforts within a Nordic Geodetic Commission (NKG) activity towards a model of glacial isostatic adjustment for Fennoscandia. The new model, NKG201xGIA, to be developed in the near future will complement the forthcoming empirical NKG land uplift model, which will substitute the currently used empirical land uplift model NKG2005LU (Ågren & Svensson, 2007). Together, the models will be a reference for vertical and horizontal motion, gravity and geoid change and more. NKG201xGIA will also provide uncertainty estimates for each field. Following former investigations, the GIA model is based on a combination of an ice and an earth model. The selected reference ice model, GLAC, for Fennoscandia, the Barents/Kara seas and the British Isles is provided by Lev Tarasov and co-workers. Tests of different ice and earth models will be performed based on the expertise of each involved modeler. This includes studies on high resolution ice sheets, different rheologies, lateral variations in lithosphere and mantle viscosity and more. This will also be done in co-operation with scientists outside NKG who help in the development and testing of the model. References Ågren, J., Svensson, R. (2007): Postglacial Land Uplift Model and System Definition for the New Swedish Height System RH 2000. Reports in Geodesy and Geographical Information Systems Rapportserie, LMV-Rapport 4, Lantmäteriet, Gävle.

Determination of the Territorial Sea Baseline - Measurement Aspect

NASA Astrophysics Data System (ADS)

Specht, Cezary; Weintrit, Adam; Specht, Mariusz; Dabrowski, Pawel

2017-12-01

Determining the course of the territorial sea baseline (TSB) of the coastal state is the basis for establishing its maritime boundaries, thus becoming indirect part of maritime policy of the state. Besides the following aspects: legal and methodological as described in the conventions, acts, standards and regulations, equally important is the issue of measurement methodology with respect to the boundaries of the territorial sea. The publication discussed accuracy requirements of the TSB measurement implementation, the relationship of sea level with a choice of the method of its determination, and discussed the implementation of such a measurement on a selected example. As the test reservoir was used the 400-meter stretch of the public beach in Gdynia. During the measurements they used the GNSS geodetic receiver operating in real time based on the geodetic network - VRSnet.pl. Additionally, a comparison was made of the applied method with analogous measurements of the TSB performed in 1999.

Carrier phase ambiguity resolution for the Global Positioning System applied to geodetic baselines up to 2000 km

NASA Technical Reports Server (NTRS)

Blewitt, Geoffrey

1989-01-01

A technique for resolving the ambiguities in the GPS carrier phase data (which are biased by an integer number of cycles) is described which can be applied to geodetic baselines up to 2000 km in length and can be used with dual-frequency P code receivers. The results of such application demonstrated that a factor of 3 improvement in baseline accuracy could be obtained, giving centimeter-level agreement with coordinates inferred by very-long-baseline interferometry in the western United States. It was found that a method using pseudorange data is more reliable than one using ionospheric constraints for baselines longer than 200 km. It is recommended that future GPS networks have a wide spectrum of baseline lengths (ranging from baselines shorter than 100 km to those longer than 1000 km) and that GPS receivers be used which can acquire dual-frequency P code data.

Historical Review of Astro-Geodetic Observations in Serbia

NASA Astrophysics Data System (ADS)

Ogrizovic, V.; Delcev, S.; Vasilic, V.; Gucevic, J.

2008-10-01

Astro-geodetic determinations of vertical deflections in Serbia began during the first years of 20th century. The first field works were led by S. Bo\\vsković. After the 2nd World War, Military Geographic Institute, Department of Geodesy from the Faculty of Civil Engineering, and Federal Geodetic Directorate continued the determinations, needed for reductions of terrestrial geodetic measurements and the astro-geodetic geoid determination. Last years improvements of the astro-geodetic methods are carried out in the area of implementing modern measurement equipment and technologies.

Correlated errors in geodetic time series: Implications for time-dependent deformation

USGS Publications Warehouse

Langbein, J.; Johnson, H.

1997-01-01

Analysis of frequent trilateration observations from the two-color electronic distance measuring networks in California demonstrate that the noise power spectra are dominated by white noise at higher frequencies and power law behavior at lower frequencies. In contrast, Earth scientists typically have assumed that only white noise is present in a geodetic time series, since a combination of infrequent measurements and low precision usually preclude identifying the time-correlated signature in such data. After removing a linear trend from the two-color data, it becomes evident that there are primarily two recognizable types of time-correlated noise present in the residuals. The first type is a seasonal variation in displacement which is probably a result of measuring to shallow surface monuments installed in clayey soil which responds to seasonally occurring rainfall; this noise is significant only for a small fraction of the sites analyzed. The second type of correlated noise becomes evident only after spectral analysis of line length changes and shows a functional relation at long periods between power and frequency of and where f is frequency and ?? ??? 2. With ?? = 2, this type of correlated noise is termed random-walk noise, and its source is mainly thought to be small random motions of geodetic monuments with respect to the Earth's crust, though other sources are possible. Because the line length changes in the two-color networks are measured at irregular intervals, power spectral techniques cannot reliably estimate the level of I//" noise. Rather, we also use here a maximum likelihood estimation technique which assumes that there are only two sources of noise in the residual time series (white noise and randomwalk noise) and estimates the amount of each. From this analysis we find that the random-walk noise level averages about 1.3 mm/Vyr and that our estimates of the white noise component confirm theoretical limitations of the measurement technique. In addition, the seasonal noise can be as large as 3 mm in amplitude but typically is less than 0.5 mm. Because of the presence of random-walk noise in these time series, modeling and interpretation of the geodetic data must account for this source of error. By way of example we show that estimating the time-varying strain tensor (a form of spatial averaging) from geodetic data having both random-walk and white noise error components results in seemingly significant variations in the rate of strain accumulation; spatial averaging does reduce the size of both noise components but not their relative influence on the resulting strain accumulation model. Copyright 1997 by the American Geophysical Union.

The African Reference Frame (AFREF) project: a fundamental geodetic tool for Africa

NASA Astrophysics Data System (ADS)

Farah, H.

2009-04-01

AFREF has as objective the establishment and maintenance of a unified geodetic reference frame for Africa, which will support and facilitate fundamental scientific and technical projects. The installation of observation systems all over Africa will provide important data that can be used in many different scientific fields (e.g., geodynamics, meteorological). Furthermore, AFREF will create an uniform frame that will support development projects, uniform environmental and mapping programmes as well as aid in resolving current and future international boundary disputes. This reference frame will be based on the International Terrestrial Reference Frame (ITRF) and will be realised through the establishment of a network of permanent Global Navigation Satellite System (GNSS) receivers. In close collaboration with several institutional role players, AFREF is an initiative of the United Nations Economic Commission for Africa (UNECA) Committee on Development Information (CODI). A steering committee is currently responsible for the over-all management and coordination of the implementation of AFREF. Implementation of AFREF is envisaged to be at national level in collaboration with National Mapping Organizations. Furthermore, many scientific Institutions are contributing for the densification of the network. The current status of the AFREF network will be discussed in detail. Several CORS systems have been installed to support AFREF specifically. In addition, most or all of the IGS stations located in Africa will automatically qualify as AFREF core stations. Furthermore, we will show examples of interaction between specific projects and AFREF that are contributing for the development of science in Africa.

EPOS-GNSS - Improving the infrastructure for GNSS data and products in Europe

NASA Astrophysics Data System (ADS)

Fernandes, Rui; Bos, Machiel; Bruyninx, Carine; Crocker, Paul; Dousa, Jan; Socquet, Anne; Walpersdorf, Andrea; Avallone, Antonio; Ganas, Athanassios; Gunnar, Benedikt; Ionescu, Constantin; Kenyeres, Ambrus; Ozener, Haluk; Vergnolle, Mathilde; Lidberg, Martin; Liwosz, Tomek; Soehne, Wolfgang

2017-04-01

EPOS-IP WP10 - "GNSS Data & Products" is the Working Package 10 of the European Plate Observing System - Implementation Phase project in charge of implementing services for the geo-sciences community to access existing Pan-European Geodetic Infrastructures. WP10 is currently formed by representatives of participating European institutions but in the operational phase contributions will be solicited from the entire geodetic community. In fact, WP10 also includes members from other institutions/countries that formally are not participating in the EPOS-IP but will be key players in the future services to be provided by EPOS. Additionally, several partners are also key partners at EUREF, which is also actively collaborating with EPOS. The geodetic component of EPOS is dealing essentially with implementing an e-infrastructure to store and disseminate the continuous GNSS data from existing Research Infrastructures. Present efforts are on developing geodetic tools to support Solid Earth research by optimizing the existing resources. However, other research and technical applications (e.g., reference frames, meteorology, space weather) can also benefit in the future from the optimization of the geodetic resources in Europe. We present and discuss the status of the implementation of the thematic and core services (TCS) for GNSS data within EPOS and the related business plan. We explain the tools and web-services being developed towards the implementation of the best solutions that will permit to the end-users, and in particular geo-scientists, to access the geodetic data, derived solutions, and associated metadata using a transparent and standardized processes. We also detail the different DDSS (Data, Data-Products, Services, Software) that will be made available for the Operational Phase of EPOS, which will start to be tested and made available during 2017 and 2018.

VLBI: A Fascinating Technique for Geodesy and Astrometry

NASA Technical Reports Server (NTRS)

Schuh, H.; Behrend, Dirk

2012-01-01

Since the 1970s Very Long Baseline Interferometry (VLBI) has proven to be a primary space-geodetic technique by determining precise coordinates on the Earth, by monitoring the variable Earth rotation and orientation with highest precision, and by deriving many other parameters of the Earth system. VLBI provides an important linkage to astronomy through, for instance, the determination of very precise coordinates of extragalactic radio sources. Additionally, it contributes to determining parameters of relativistic and cosmological models. After a short review of the history of geodetic VLBI and a summary of recent results, this paper describes future perspectives of this fascinating technique. The International VLBI Service for Geodesy and Astrometry (IVS), as a service of the International Association of Geodesy (IAG) and the International Astronomical Union (IAU), is well on its way to fully defining a next generation VLBI system, called VLBI2010. The goals of the new system are to achieve on scales up to the size of the Earth an accuracy of 1 mm in position and of 0.1 mm/year in velocity. Continuous observations shall be carried out 24 h per day 7 days per week in the future with initial results to be delivered within 24 h after taking the data. Special sessions, e.g. for monitoring the Earth rotation parameters, will provide the results in near real-time. These goals require a completely new technical and conceptual design of VLBI measurements. Based on extensive simulation studies, strategies have been developed by the IVS to significantly improve its product accuracy through the use of a network of small (approx 12 m) fast-slewing antennas. A new method for generating high precision delay measurements as well as improved methods for handling biases related to radio source structure, system electronics, and deformations of the antenna structures has been developed. Furthermore, as of January 2012, the construction of ten new VLBI2010 sites has been funded, with good prospects for one dozen more antennas, which will improve the geographical distribution of geodetic VLBI sites on Earth and provide an important step toward a global VLBI2010 network. Within this paper, the Global Geodetic Observing System (GGOS) of the IAG will also be introduced and the contribution of VLBI to GGOS will be described.

Error assessment of local tie vectors in space geodesy

NASA Astrophysics Data System (ADS)

Falkenberg, Jana; Heinkelmann, Robert; Schuh, Harald

2014-05-01

For the computation of the ITRF, the data of the geometric space-geodetic techniques on co-location sites are combined. The combination increases the redundancy and offers the possibility to utilize the strengths of each technique while mitigating their weaknesses. To enable the combination of co-located techniques each technique needs to have a well-defined geometric reference point. The linking of the geometric reference points enables the combination of the technique-specific coordinate to a multi-technique site coordinate. The vectors between these reference points are called "local ties". The realization of local ties is usually reached by local surveys of the distances and or angles between the reference points. Identified temporal variations of the reference points are considered in the local tie determination only indirectly by assuming a mean position. Finally, the local ties measured in the local surveying network are to be transformed into the ITRF, the global geocentric equatorial coordinate system of the space-geodetic techniques. The current IERS procedure for the combination of the space-geodetic techniques includes the local tie vectors with an error floor of three millimeters plus a distance dependent component. This error floor, however, significantly underestimates the real accuracy of local tie determination. To fullfill the GGOS goals of 1 mm position and 0.1 mm/yr velocity accuracy, an accuracy of the local tie will be mandatory at the sub-mm level, which is currently not achievable. To assess the local tie effects on ITRF computations, investigations of the error sources will be done to realistically assess and consider them. Hence, a reasonable estimate of all the included errors of the various local ties is needed. An appropriate estimate could also improve the separation of local tie error and technique-specific error contributions to uncertainties and thus access the accuracy of space-geodetic techniques. Our investigations concern the simulation of the error contribution of each component of the local tie definition and determination. A closer look into the models of reference point definition, of accessibility, of measurement, and of transformation is necessary to properly model the error of the local tie. The effect of temporal variations on the local ties will be studied as well. The transformation of the local survey into the ITRF can be assumed to be the largest error contributor, in particular the orientation of the local surveying network to the ITRF.

Using the Global Navigation Satellite System (GNSS) data for Hazard Estimation in Some Active Regions in Egypt

NASA Astrophysics Data System (ADS)

Sayed Mohamed, Abdel-Monem

2016-07-01

Egypt rapidly growing development is accompanied by increasing levels of standard living particular in its urban areas. However, there is a limited experience in quantifying the sources of risk management in Egypt and in designing efficient strategies to keep away serious impacts of earthquakes. From the historical point of view and recent instrumental records, there are some seismo-active regions in Egypt, where some significant earthquakes had occurred in different places. The special tectonic features in Egypt: Aswan, Greater Cairo, Red Sea and Sinai Peninsula regions are the territories of a high seismic risk, which have to be monitored by up-to date technologies. The investigations of the seismic events and interpretations led to evaluate the seismic hazard for disaster prevention and for the safety of the dense populated regions and the vital national projects as the High Dam. In addition to the monitoring of the recent crustal movements, the most powerful technique of satellite geodesy GNSS are used where geodetic networks are covering such seismo-active regions. The results from the data sets are compared and combined in order to determine the main characteristics of the deformation and hazard estimation for specified regions. The final compiled output from the seismological and geodetic analysis threw lights upon the geodynamical regime of these seismo-active regions and put Aswan and Greater Cairo under the lowest class according to horizontal crustal strains classifications. This work will serve a basis for the development of so-called catastrophic models and can be further used for catastrophic risk management. Also, this work is trying to evaluate risk of large catastrophic losses within the important regions including the High Dam, strategic buildings and archeological sites. Studies on possible scenarios of earthquakes and losses are a critical issue for decision making in insurance as a part of mitigation measures.

Added-value joint source modelling of seismic and geodetic data

NASA Astrophysics Data System (ADS)

Sudhaus, Henriette; Heimann, Sebastian; Walter, Thomas R.; Krueger, Frank

2013-04-01

In tectonically active regions earthquake source studies strongly support the analysis of the current faulting processes as they reveal the location and geometry of active faults, the average slip released or more. For source modelling of shallow, moderate to large earthquakes often a combination of geodetic (GPS, InSAR) and seismic data is used. A truly joint use of these data, however, usually takes place only on a higher modelling level, where some of the first-order characteristics (time, centroid location, fault orientation, moment) have been fixed already. These required basis model parameters have to be given, assumed or inferred in a previous, separate and highly non-linear modelling step using one of the these data sets alone. We present a new earthquake rupture model implementation that realizes a fully combined data integration of surface displacement measurements and seismic data in a non-linear optimization of simple but extended planar ruptures. The model implementation allows for fast forward calculations of full seismograms and surface deformation and therefore enables us to use Monte Carlo global search algorithms. Furthermore, we benefit from the complementary character of seismic and geodetic data, e. g. the high definition of the source location from geodetic data and the sensitivity of the resolution of the seismic data on moment releases at larger depth. These increased constraints from the combined dataset make optimizations efficient, even for larger model parameter spaces and with a very limited amount of a priori assumption on the source. A vital part of our approach is rigorous data weighting based on the empirically estimated data errors. We construct full data error variance-covariance matrices for geodetic data to account for correlated data noise and also weight the seismic data based on their signal-to-noise ratio. The estimation of the data errors and the fast forward modelling opens the door for Bayesian inferences of the source model parameters. The source model product then features parameter uncertainty estimates and reveals parameter trade-offs that arise from imperfect data coverage and data errors. We applied our new source modelling approach to the 2010 Haiti earthquake for which a number of apparently different seismic, geodetic and joint source models has been reported already - mostly without any model parameter estimations. We here show that the variability of all these source models seems to arise from inherent model parameter trade-offs and mostly has little statistical significance, e.g. even using a large dataset comprising seismic and geodetic data the confidence interval of the fault dip remains as wide as about 20 degrees.

Free geometric adjustment of the SECOR Equatorial Network (Solution SECOR-27)

NASA Technical Reports Server (NTRS)

Mueller, I. I.; Kumar, M.; Soler, T.

1973-01-01

The basic purpose of this experiment is to compute reduced normal equations from the observational data of the SECOR Equatorial Network obtained from DMA/Topographic Center, D/Geodesy, Geosciences Div. Washington, D.C. These reduced normal equations are to be combined with reduced normal equations of other satellite networks of the National Geodetic Satellite Program to provide station coordinates from a single least square adjustment. An individual SECOR solution was also obtained and is presented in this report, using direction constraints computed from BC-4 optical data from stations collocated with SECOR stations. Due to the critical configuration present in the range observations, weighted height constraints were also applied in order to break the near coplanarity of the observing stations.

Coordinating, Scheduling, Processing and Analyzing IYA09

NASA Technical Reports Server (NTRS)

Gipson, John; Behrend, Dirk; Gordon, David; Himwich, Ed; MacMillan, Dan; Titus, Mike; Corey, Brian

2010-01-01

The IVS scheduled a special astrometric VLBI session for the International Year of Astronomy 2009 (IYA09) commemorating 400 years of optical astronomy and 40 years of VLBI. The IYA09 session is the most ambitious geodetic session to date in terms of network size, number of sources, and number of observations. We describe the process of designing, coordinating, scheduling, pre-session station checkout, correlating, and analyzing this session.

Investigation of land subsidence due to climate changes in surrounding areas of Urmia Lake (located in northwest of Iran) using wavelet coherence analysis of geodetic measurements and methodological data

NASA Astrophysics Data System (ADS)

Moghtased-Azar, K.; Mirzaei, A.; Nankali, H. R.; Tavakoli, F.

2012-04-01

Urmia Lake (salt lake in northwest of Iran) plays a valuable role in environment, wildlife and economy of Iran and the region, and now faces great challenges for survival. The Lake is in immediate and great danger and rapidly going to become salty desert. During the recent years and new heat wave, Iran, like many other countries are experiencing, is faced with relativity reduced rain fall. From a few years ago environment activists warned about potential dangers. Geodetic measurements, e.g., repeated leveling measurements of first order leveling network of Iran and continuous GPS measurements of Iranian Permanent GPS network of Iran (IPGN) showed that there is subsidence in surrounding areas of the lake. This paper investigates the relation between subsidence and climate changing in the area, using the wavelet coherence of the data of permanent GPS stations and daily methodological data. The results show that there is strong coherence between the subsidence phenomena induced by GPS data and climate warming from January 2009 up to end of August 2009. However, relative lake height variations computed from altimetry observations (TOPEX/POSEIDON (T/P), Jason-1 and Jason-2/OSTM) confirms maximum evaporation rates of the lake in this period.

Elements of an algorithm for optimizing a parameter-structural neural network

NASA Astrophysics Data System (ADS)

Mrówczyńska, Maria

2016-06-01

The field of processing information provided by measurement results is one of the most important components of geodetic technologies. The dynamic development of this field improves classic algorithms for numerical calculations in the aspect of analytical solutions that are difficult to achieve. Algorithms based on artificial intelligence in the form of artificial neural networks, including the topology of connections between neurons have become an important instrument connected to the problem of processing and modelling processes. This concept results from the integration of neural networks and parameter optimization methods and makes it possible to avoid the necessity to arbitrarily define the structure of a network. This kind of extension of the training process is exemplified by the algorithm called the Group Method of Data Handling (GMDH), which belongs to the class of evolutionary algorithms. The article presents a GMDH type network, used for modelling deformations of the geometrical axis of a steel chimney during its operation.

Steady, modest slip over multiple earthquake cycles on the Owens Valley and Little Lake fault zones

NASA Astrophysics Data System (ADS)

Amos, C. B.; Haddon, E. K.; Burgmann, R.; Zielke, O.; Jayko, A. S.

2015-12-01

A comprehensive picture of current plate-boundary deformation requires integration of short-term geodetic records with longer-term geologic strain. Comparing rates of deformation across these time intervals highlights potential time-dependencies in both geodetic and geologic records and yields critical insight into the earthquake deformation process. The southern Walker Lane Belt in eastern California represents one location where short-term strain recorded by geodesy apparently outpaces longer-term geologic fault slip measured from displaced rocks and landforms. This discrepancy persists both for individual structures and across the width of the deforming zone, where ~1 cm/yr of current dextral shear exceeds Quaternary slip rates summed across individual faults. The Owens Valley and Little Lake fault systems form the western boundary of the southern Walker Lane and host a range of published slip rate estimates from ~1 - 7 mm/yr over varying time intervals based on both geodetic and geologic measurements. New analysis of offset geomorphic piercing lines from airborne lidar and field measurements along the Owens Valley fault provides a snapshot of deformation during individual earthquakes and over many seismic cycles. Viewed in context of previously reported ages from pluvial and other landforms in Owens Valley, these offsets suggest slip rates of ~0.6 - 1.6 mm/yr over the past 103 - 105 years. Such rates agree with similar estimates immediately to the south on the Little Lake fault, where lidar measurements indicate dextral slip averaging ~0.6 - 1.3 mm/yr over comparable time intervals. Taken together, these results suggest steady, modest slip in the absence of significant variations over the Mid-to-Late Quaternary for a ~200 km span of the southwestern Walker Lane. Our findings argue against the presence of long-range fault interactions and slip-rate variations for this portion of the larger, regional fault network. This result also suggests that faster slip-rate estimates from geodetic measurements reflect transients over much shorter time scales. Additionally, the persistence of relatively faster geodetic shear in comparison with time-averaged fault slip leaves open the possibility of significant off-fault deformation or slip on subsidiary structures across the Owens Valley.

Developments for the Automation and Remote Control of the Radio Telescopes of the Geodetic Observatory Wettzell

NASA Astrophysics Data System (ADS)

Neidhardt, Alexander; Schönberger, Matthias; Plötz, Christian; Kronschnabl, Gerhard

2014-12-01

VGOS is a challenge for all fields of a new radio telescope. For the future software and hardware control mechanisms, it also requires new developments and solutions. More experiments, more data, high-speed data transfers through the Internet, and a real-time monitoring of current system status information must be handled. Additionally, an optimization of the observation shifts is required to reduce work load and costs. Within the framework of the development of the new 13.2-m Twin radio Telescopes Wettzell (TTW) and in combination with upgrades of the 20-m Radio Telescope Wettzell (RTW), some new technical realizations are under development and testing. Besides the activities for the realization of remote control, mainly supported during the project ``Novel EXploration Pushing Robust e-VLBI Services (NEXPReS)'' of the European VLBI Network (EVN), autonomous, automated, and unattended observations are also planned. A basic infrastructure should enable these, e.g., independent monitoring and security systems or additional, local high-speed transfer networks to ship data directly from a telescope to the main control room.

Ukiah and Gaithersburg Latitude Observatories: Preserving NOAA's Legacy of International Scientific Cooperation and Polar Motion Studies

NASA Astrophysics Data System (ADS)

Caccamise, D. J., II; Stone, W. A.

2016-12-01

In 1891, American astronomer Seth C. Chandler Jr. announced his discovery that the earth's axis of rotation—and hence the direction of true north—wobbles within the earth with a period of about 14 months, varying latitude everywhere on the globe. Immediately, the International Geodetic Association (IGA) called for an unprecedented international effort to observe and measure the wandering of the earth's pole and its resulting variation of latitude. The U.S. Coast and Geodetic Survey became involved, and by 1899 the IGA had established six International Latitude Observatories at 39° 8' N: three in the United States, the others in Italy, Russia and Japan. Only two of the U.S. latitude observatories survive today. In 1982, NOAA deeded them to their home cities of Gaithersburg, MD and Ukiah, CA. Both cities have embraced this history by restoring the observatories and converting the adjacent land into public parks. Gaithersburg has had its latitude observatory dedicated as a National Historic Landmark. In 2014-15, the National Geodetic Survey (the present-day NOAA successor to the U.S. Coast and Geodetic Survey) loaned the original zenith telescopes to the communities, returning the observatories to their original condition. This poster/presentation will outline the motivations for this effort and bring to fruition this cooperative multi-year effort among partners by providing examples of NOAA's mission and contribution to science, service and stewardship at both the east and west coast geodetic observatories, through programs and historic exhibits for students and the public. Results will include an increase in exposure to NOAA's rich and formative heritage as well as its enduring current scientific research and other activities. Thus, NOAA's historic heritage and assets of the International Latitude Observatories will be protected and preserved through activities for education, outreach and tourism.

Seismic and Aseismic Behavior of the Altotiberina Low-angle Normal Fault System (Northern Apennines, Italy) through High-resolution Earthquake Locations and Repeating Events

NASA Astrophysics Data System (ADS)

Valoroso, L.; Chiaraluce, L.

2017-12-01

Low-angle normal faults (dip < 30°) are geologically widely documented and considered responsible for accommodating the crustal extension within the brittle crust although their mechanical behavior and seismogenic potential is enigmatic. We study the anatomy and slip-behavior of the actively slipping Altotiberina low-angle (ATF) normal fault system using a high-resolution 5-years-long (2010-2014) earthquake catalogue composed of 37k events (ML<3.9 and completeness magnitude MC=0.5 ML), recorded by a dense permanent seismic network of the Altotiberina Near Fault Observatory (TABOO). The seismic activity defines the fault system dominated at depth by the low-angle ATF surface (15-20°) coinciding to the ATF geometry imaged through seismic reflection data. The ATF extends for 50km along-strike and between 4-5 to 16km of depth. Seismicity also images the geometry of a set of higher angle faults (35-50°) located in the ATF hanging-wall (HW). The ATF-related seismicity accounts for 10% of the whole seismicity (3,700 events with ML<2.4), occurring at a remarkably constant rate of 2.2 events/day. This seismicity describes an about 1.5-km-thick fault zone composed by multiple sub-parallel slipping planes. The remaining events are instead organized in multiple mainshocks (MW>3) seismic sequences lasting from weeks to months, activating a contiguous network of 3-5-km-long syn- and antithetic fault segments within the ATF-HW. The space-time evolution of these minor sequences is consistent with subsequence failures promoted by fluid flow. The ATF-seismicity pattern includes 97 clusters of repeating events (RE) made of 299 events with ML<1.9. RE are located around locked patches identified by geodetic modeling, suggesting a mixed-mode (stick-slip and stable-sliding) slip-behavior along the fault plane in accommodating most of the NE-trending tectonic deformation with creeping dominating below 5 km depth. Consistently, the seismic moment released by the ATF-seismicity accounts for a small portion (30%) of the geodetic one. The rate of occurrence of RE, mostly composed by doublets with short inter-event time (e.g. hours), appears to modulate the seismic release of the ATF-HW, suggesting that creeping may drive the strain partitioning of the system.

Technical and Organizational Lessons Learned From More Than One Decade of the International GNSS Service Global Tracking Network

NASA Astrophysics Data System (ADS)

Moore, A. W.

2007-12-01

The International GNSS Service (IGS) is a voluntary collaboration of more than 200 worldwide agencies that pool resources to generate precise GPS and GLONASS products. The foundation of the IGS is a global network of 385 permanent, continuous, geodetic-quality stations independently operated by about 100 agencies. The IGS Central Bureau develops minimum functional requirements and operational standards that enable the individual stations' data to be used coherently in global analyses, but the IGS remains vendor neutral, leaving procurement decisions and implementation details to the individual agencies. The IGS network is hence quite heterogeneous in instrumentation, station management strategies, and culture; these diversities bring both strengths and challenges in coordination. This presentation will detail the IGS's approaches, successes, and opportunities for improvement in coordinating and monitoring the collaborative network.

Paradoxes of the comparative analysis of ground-based and satellite geodetic measurements in recent geodynamics

NASA Astrophysics Data System (ADS)

Kuzmin, Yu. O.

2017-11-01

The comparative analysis of the Earth's surface deformations measured by ground-based and satellite geodetic methods on the regional and zonal measurement scales is carried out. The displacement velocities and strain rates are compared in the active regions such as Turkmenian-Iranian zone of interaction of the Arabian and Eurasian lithospheric plates and the Kamchatka segment of the subduction of the Pacific Plate beneath the Okotsk Plate. The comparison yields a paradoxical result. With the qualitatively identical kinematics of the motion, the quantitative characteristics of the displacement velocities and rates of strain revealed by the observations using the global navigational satellite system (GNSS) are by 1-2 orders of magnitude higher than those estimated by the more accurate methods of ground-based geodesy. For resolving the revealed paradoxes, it is required to set up special studies on the joint analysis of ground-based and satellite geodetic data from the combined observation sites.

Retrieval and Validation of Zenith and Slant Path Delays From the Irish GPS Network

NASA Astrophysics Data System (ADS)

Hanafin, Jennifer; Jennings, S. Gerard; O'Dowd, Colin; McGrath, Ray; Whelan, Eoin

2010-05-01

Retrieval of atmospheric integrated water vapour (IWV) from ground-based GPS receivers and provision of this data product for meteorological applications has been the focus of a number of Europe-wide networks and projects, most recently the EUMETNET GPS water vapour programme. The results presented here are from a project to provide such information about the state of the atmosphere around Ireland for climate monitoring and improved numerical weather prediction. Two geodetic reference GPS receivers have been deployed at Valentia Observatory in Co. Kerry and Mace Head Atmospheric Research Station in Co. Galway, Ireland. These two receivers supplement the existing Ordnance Survey Ireland active network of 17 permanent ground-based receivers. A system to retrieve column-integrated atmospheric water vapour from the data provided by this network has been developed, based on the GPS Analysis at MIT (GAMIT) software package. The data quality of the zenith retrievals has been assessed using co-located radiosondes at the Valentia site and observations from a microwave profiling radiometer at the Mace Head site. Validation of the slant path retrievals requires a numerical weather prediction model and HIRLAM (High-Resolution Limited Area Model) version 7.2, the current operational forecast model in use at Met Éireann for the region, has been used for this validation work. Results from the data processing and comparisons with the independent observations and model will be presented.

Bounding the moment deficit rate on crustal faults using geodetic data: Methods

DOE PAGES

Maurer, Jeremy; Segall, Paul; Bradley, Andrew Michael

2017-08-19

Here, the geodetically derived interseismic moment deficit rate (MDR) provides a first-order constraint on earthquake potential and can play an important role in seismic hazard assessment, but quantifying uncertainty in MDR is a challenging problem that has not been fully addressed. We establish criteria for reliable MDR estimators, evaluate existing methods for determining the probability density of MDR, and propose and evaluate new methods. Geodetic measurements moderately far from the fault provide tighter constraints on MDR than those nearby. Previously used methods can fail catastrophically under predictable circumstances. The bootstrap method works well with strong data constraints on MDR, butmore » can be strongly biased when network geometry is poor. We propose two new methods: the Constrained Optimization Bounding Estimator (COBE) assumes uniform priors on slip rate (from geologic information) and MDR, and can be shown through synthetic tests to be a useful, albeit conservative estimator; the Constrained Optimization Bounding Linear Estimator (COBLE) is the corresponding linear estimator with Gaussian priors rather than point-wise bounds on slip rates. COBE matches COBLE with strong data constraints on MDR. We compare results from COBE and COBLE to previously published results for the interseismic MDR at Parkfield, on the San Andreas Fault, and find similar results; thus, the apparent discrepancy between MDR and the total moment release (seismic and afterslip) in the 2004 Parkfield earthquake remains.« less

Bounding the moment deficit rate on crustal faults using geodetic data: Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maurer, Jeremy; Segall, Paul; Bradley, Andrew Michael

Here, the geodetically derived interseismic moment deficit rate (MDR) provides a first-order constraint on earthquake potential and can play an important role in seismic hazard assessment, but quantifying uncertainty in MDR is a challenging problem that has not been fully addressed. We establish criteria for reliable MDR estimators, evaluate existing methods for determining the probability density of MDR, and propose and evaluate new methods. Geodetic measurements moderately far from the fault provide tighter constraints on MDR than those nearby. Previously used methods can fail catastrophically under predictable circumstances. The bootstrap method works well with strong data constraints on MDR, butmore » can be strongly biased when network geometry is poor. We propose two new methods: the Constrained Optimization Bounding Estimator (COBE) assumes uniform priors on slip rate (from geologic information) and MDR, and can be shown through synthetic tests to be a useful, albeit conservative estimator; the Constrained Optimization Bounding Linear Estimator (COBLE) is the corresponding linear estimator with Gaussian priors rather than point-wise bounds on slip rates. COBE matches COBLE with strong data constraints on MDR. We compare results from COBE and COBLE to previously published results for the interseismic MDR at Parkfield, on the San Andreas Fault, and find similar results; thus, the apparent discrepancy between MDR and the total moment release (seismic and afterslip) in the 2004 Parkfield earthquake remains.« less

A strawman SLR program plan for the 1990s

NASA Technical Reports Server (NTRS)

Degnan, John J.

1994-01-01

A series of programmatic and technical goals for the satellite laser ranging (SLR) network are presented. They are: (1) standardize the performance of the global SLR network; (2) improve the geographic distribution of stations; (3) reduce costs of field operations and data processing; (4) expand the 24 hour temporal coverage to better serve the growing constellation of satellites; (5) improve absolute range accuracy to 2 mm at key stations; (6) improve satellite force, radiative propagation, and station motion models and investigate alternative geodetic analysis techniques; (7) support technical intercomparison and the Terrestrial Reference Frame through global collocations; (8) investigate potential synergisms between GPS and SLR.

Building a Catalog of Time-Dependent Inversions for Cascadia ETS Events

NASA Astrophysics Data System (ADS)

Bartlow, N. M.; Williams, C. A.; Wallace, L. M.

2017-12-01

Episodic Tremor and Slip (ETS), composed of periodically occurring slow slip events accompanied by tectonic tremor, have been recognized in Cascadia since 1999. While the tremor has been continuously and automatically monitored for a few years (Wech et al., SRL, 2010; pnsn.org/tremor), the geodetically-derived slip has not been systematically monitored in the same way. Instead, numerous time-dependent and static inversions of the geodetic data have been performed for individual ETS events, with many events going unstudied. Careful study of, and monitoring of, ETS is important both to advance the scientific understanding of fault mechanics and to improve earthquake hazard forecasting in Cascadia. Here we present the results of initial efforts to standardize geodetic inversions of slow slip during Cascadia ETS. We use the Network Inversion Filter (NIF, Segall and Matthews,1997; McGuire and Segall, 2003; Miyazaki et al.,2006), applied evenly to an extended time period, to detect and catalog slow slip transients. Bartlow et al., 2014, conducted a similar study for the Hikurangi subduction zone, covering a 2.5 year period. Additionally, we generate Green's functions using the PyLith finite element code (Aagaard et al., 2013) to allow consideration of elastic property variations derived from a Cascadia-wide seismic velocity model (Stephenson, USGS pub., 2007). These Green's functions are then integrated to provide Green's functions compatible with the Network Inversion Filter. The use of heterogeneous elastic Green's functions allows for a more accurate estimation of slip amplitudes, both during individual ETS events and averaged over multiple events. This is useful for constraining the total slip budget in Cascadia, including whether ETS takes up the entire plate motion on the deeper extent of the plate interface where it occurs. The recent study of Williams and Wallace, GRL, 2015 demonstrated that the use heterogeneous elastic Green's Functions in inversions can make a significant difference in resulting slip distributions.

GPS Velocity Field at the Western Tip of the Aden Ridge ; Implications for Rifting and the Arabia-Somalia-Nubia Triple Junction Dynamics

NASA Astrophysics Data System (ADS)

Doubre, C.; Socquet, A.; Masson, F.; Cressot, C.; Mohamed, K.; Vigny, C.; Ruegg, J.

2010-12-01

Due to the presence of magma and a complex thermal structure, the dynamics of divergent plate boundaries are complicated, with microseismicity (ML<4) contributing very little to the total moment release. For the last 35 years several geodetic campaigns have been conducted at the western tip of the Aden Ridge propagating on land into Afar (Republic of Djibouti). The first segment above water, the Asal Rift, experienced a seismo-volcanic event in 1978, which was the first rifting episode, along with the 1978-1985 Icelandic Krafla event, to be monitored by terrestrial geodetic measurements. These measurements revealed the opening of two 1-2 m-wide dykes in the rift inner floor. Since then, terrestrial and spatial geodetic monitoring shows that the rift kept opening, during the post-rifting period, at a rate largely exceeding the plates’ motions. This significant opening rate is decreasing with time to tend, three decades after the rifting event, to the far-field opening rate. We present here the results of the GPS measurements of a 45 site network covering the Tadjoura-Asal Rift System, previously made every two years from 1995 to 2003, and repeated in 2010. The calculated 1999-2010 horizontal velocity field is very homogeneous with a quasi-constant N045° direction with respect to Somalia and a regular increase from the southern to the northern margin of the Asal Rift clearly controlled by a few normal faults, and reaching a maximum of 12.5 mm/yr. A non-negligible part of the Arabia-Somalia divergent movement (1 to 2 mm/yr) is observed south of this rift, which sheds light on the role of the active normal faults bounding the asymmetrical Gaggadé Basin and therefore brings important constraints on the location of the Red Sea Ridge-Aden Ridge-East African Rift triple junction. Since the last 2003 campaign, the lack of micro-seismicity within the Asal Rift seems to be associated with a ˜2 mm/yr decrease of the opening rate deduced from the GPS time series analysis. These results confirm the importance of non-steady state behavior of the Asal volcano-tectonic rift segment, and the role of geothermal/volcanic activity on the occurrence of transients, as suggested by InSAR results.

Geodetic Measurements and Numerical Modeling of the Deformation Cycle for Okmok Volcano, Alaska: 1993-2008

NASA Astrophysics Data System (ADS)

Ohlendorf, S. J.; Feigl, K.; Thurber, C. H.; Lu, Z.; Masterlark, T.

2011-12-01

Okmok Volcano is an active caldera located on Umnak Island in the Aleutian Island arc. Okmok, having recently erupted in 1997 and 2008, is well suited for multidisciplinary studies of magma migration and storage because it hosts a good seismic network and has been the subject of synthetic aperture radar (SAR) images that span the recent eruption cycle. Interferometric SAR can characterize surface deformation in space and time, while data from the seismic network provides important information about the interior processes and structure of the volcano. We conduct a complete time series analysis of deformation of Okmok with images collected by the ERS and Envisat satellites on more than 100 distinct epochs between 1993 and 2008. We look for changes in inter-eruption inflation rates, which may indicate inelastic rheologic effects. For the time series analysis, we analyze the gradient of phase directly, without unwrapping, using the General Inversion of Phase Technique (GIPhT) [Feigl and Thurber, 2009]. This approach accounts for orbital and atmospheric effects and provides realistic estimates of the uncertainties of the model parameters. We consider several models for the source, including the prolate spheroid model and the Mogi model, to explain the observed deformation. Using a medium that is a homogeneous half space, we estimate the source depth to be centered at about 4 km below sea level, consistent with the findings of Masterlark et al. [2010]. As in several other geodetic studies, we find the source to be approximately centered beneath the caldera. To account for rheologic complexity, we next apply the Finite Element Method to simulate a pressurized cavity embedded in a medium with material properties derived from body wave seismic tomography. This approach allows us to address the problem of unreasonably large pressure values implied by a Mogi source with a radius of about 1 km by experimenting with larger sources. We also compare the time dependence of the source to published results that used GPS data.

Strong Ground Motion Analysis and Afterslip Modeling of Earthquakes near Mendocino Triple Junction

NASA Astrophysics Data System (ADS)

Gong, J.; McGuire, J. J.

2017-12-01

The Mendocino Triple Junction (MTJ) is one of the most seismically active regions in North America in response to the ongoing motions between North America, Pacific and Gorda plates. Earthquakes near the MTJ come from multiple types of faults due to the interaction boundaries between the three plates and the strong internal deformation within them. Understanding the stress levels that drive the earthquake rupture on the various types of faults and estimating the locking state of the subduction interface are especially important for earthquake hazard assessment. However due to lack of direct offshore seismic and geodetic records, only a few earthquakes' rupture processes have been well studied and the locking state of the subducted slab is not well constrained. In this study we first use the second moment inversion method to study the rupture process of the January 28, 2015 Mw 5.7 strike slip earthquake on Mendocino transform fault using strong ground motion records from Cascadia Initiative community experiment as well as onshore seismic networks. We estimate the rupture dimension to be of 6 km by 3 km and a stress drop of 7 MPa on the transform fault. Next we investigate the frictional locking state on the subduction interface through afterslip simulation based on coseismic rupture models of this 2015 earthquake and a Mw 6.5 intraplate eathquake inside Gorda plate whose slip distribution is inverted using onshore geodetic network in previous study. Different depths for velocity strengthening frictional properties to start at the downdip of the locked zone are used to simulate afterslip scenarios and predict the corresponding surface deformation (GPS) movements onshore. Our simulations indicate that locking depth on the slab surface is at least 14 km, which confirms that the next M8 earthquake rupture will likely reach the coastline and strong shaking should be expected near the coast.

Installation of a seafloor geodetic network offshore northern Chile (GeoSEA)

NASA Astrophysics Data System (ADS)

Kopp, Heidrun; Lange, Dietrich; Hannemann, Katrin; Petersen, Florian; Contreras-Reyes, Eduardo

2016-04-01

The seafloor stores crucial information on sub-seafloor processes, including stress, elastic strain, and earthquake and tsunami generation. This information may be extracted through the nascent scientific field of seafloor geodesy. The target of the recently installed GeoSEA array (Geodetic Earthquake Observatory on the SEAfloor) is to measure crustal deformation in mm-scale on the marine forearc and outer rise of the South American subduction system around 21°S. This segment of the Nazca-South American plate boundary has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique/Pisagua earthquake (Mw=8.1). The southern portion of the segment remains unbroken by a recent earthquake. Seafloor geodetic measurements provide a way to monitor crustal deformation at high resolution comparable to the satellite-based GPS technique upon which terrestrial geodesy is largely based. The GeoSEA Network consists of autonomous seafloor transponders installed on 4 m high tripods, which were lowered to the seabed on the deep-sea cable of RV SONNE in December 2015. The transponders within an array intercommunicate via acoustic signals for a period of up to 3.5 years and measure acoustic distance, tilt and pressure. An additional component of the network is GeoSURF, a self-steering autonomous surface vehicle (Wave Glider), which monitors system health and is capable to upload the seafloor data to the sea surface and to transfer it via satellite. We have chosen three areas on the middle and lower slope and the outer rise for the set-up of three sub-arrays. The array in Area 1 on the middle continental slope consists of 8 transponders located in pairs on four topographic ridges, which are surface expressions of faults at depth. Area 2 is located on the outer rise seaward of the trench where 5 stations monitor extension across plate-bending related normal faults. The third area is located at water depth >5000 m on the lower continental slope where an array of 10 stations measures diffuse strain build-up. Data from all networks and all stations were successfully uploaded to GeoSURF and/or a high performance USBL transceiver lowered into the water from RV SONNE. The seabed installation of a total of 23 transponders records pressure, temperature, water sound velocity, salinity, and baselines between stations. Baselines cover distances of up to 2600 m with a precision of ±2 mm.

NOAA Photo Library - Historical Coast & Geodetic Survey Collection

Science.gov Websites

;gs photos The Historic Coast and Geodetic Survey Collection is composed of over 3,000 images of many aspects of Coast and Geodetic Survey operations including geodesy, nautical and aeronautical charting geophysics and oceanography. The Historic Coast and Geodetic Survey Collection chronicles this rich heritage

Strategies for Space-Geodetic Monitoring of Infraseismic and Subseismic Transient Deformations

NASA Technical Reports Server (NTRS)

Jordan, Thomas H.

1996-01-01

The utility of space-geodetic data in elucidating infraseismic and subseismic phenomena is assessed. Existing seismological, geodetic, and other data to characterize the distribution of infraseismic and subseismic transients are used. Strategies for space-geodetic monitoring of infraseismic and subseismic transients along major plate boundaries are developed.

Proposed satellite laser ranging and very long baseline interferometry sites for crustal dynamics investigations

NASA Technical Reports Server (NTRS)

Lowman, P. D.; Allenby, R. J.; Frey, H. V.

1979-01-01

Recommendations are presented for a global network of 125 sites for geodetic measurements by satellite laser ranging and very long baseline interferometry. The sites were proposed on the basis of existing facilities and scientific value for investigation of crustal dynamics as related to earthquake hazards. Tectonic problems are discussed for North America peripheral regions and for the world. The sites are presented in tables and maps, with bibliographic references.

Ny-Alesund Geodetic Observatory

NASA Technical Reports Server (NTRS)

Sieber, Moritz

2013-01-01

In 2012 the 20-m telescope at Ny-Alesund, Svalbard, operated by the Norwegian Mapping Authority (NMA), took part in 163 out of 168 scheduled sessions of the IVS program. Since spring, all data was transferred by network, and the receiver monitoring computer was replaced by a bus-coupler. In autumn, the NMA received building permission for a new observatory from the Governor of Svalbard. The bidding process and first construction work for the infrastructure will start in 2013.

Precise Clock Solutions Using Carrier Phase from GPS Receivers in the International GPS Service

NASA Technical Reports Server (NTRS)

Zumberge, J. F.; Jefferson, D. C.; Stowers, D. A.; Tjoelker, R. L.; Young, L. E.

1999-01-01

As one of its activities as an Analysis Center in the International GPS Service (IGS), the Jet Propulsion Laboratory (JPL) uses data from a globally distributed network of geodetic-quality GPS receivers to estimate precise clock solutions, relative to a chosen reference, for both the GPS satellites and GPS receiver internal clocks, every day. The GPS constellation and ground network provide geometrical strength resulting in formal errors of about 100 p sec for these estimates. Some of the receivers in the global IGS network contain high quality frequency references, such as hydrogen masers. The clock solutions for such receivers are smooth at the 20-p sec level on time scales of a few minutes. There are occasional (daily to weekly) shifts at the microsec level, symptomatic of receiver resets, and 200-p sec-level discontinuities at midnight due to 1-day processing boundaries. Relative clock solutions among 22 IGS sites proposed as "fiducial" in the IGS/BIPM pilot project have been examined over a recent 4-week period. This allows a quantitative measure of receiver reset frequency as a function of site. For days and-sites without resets, the Allan deviation of the relative clock solutions is also computed for subdaily values of tau..

Determination of recent horizontal crustal movements and deformations of African and Eurasian plates in western Mediterranean region using geodetic-GPS computations extended to 2006 (from 1997) related to NAFREF and AFREF frames.

NASA Astrophysics Data System (ADS)

Azzouzi, R.

2009-04-01

Determination of recent horizontal crustal movements and deformations of African and Eurasian plates in western Mediterranean region using geodetic-GPS computations extended to 2006 (from 1997) related to NAFREF and AFREF frames. By: R. Azzouzi*, M. Ettarid*, El H. Semlali*, et A. Rimi+ * Filière de Formation en Topographie Institut Agronomique et Vétérinaire Hassan II B.P. 6202 Rabat-Instituts MAROC + Département de la Physique du Globe Université Mohammed V Rabat MAROC This study focus on the use of the geodetic spatial technique GPS for geodynamic purposes generally in the Western Mediterranean area and particularly in Morocco. It aims to exploit this technique first to determine the geodetic coordinates on some western Mediterranean sites. And also this technique is used to detect and to determine movements cross the boundary line between the two African and Eurasian crustal plates on some well chosen GPS-Geodynamics sites. It will allow us also to estimate crustal dynamic parameters of tension that results. These parameters are linked to deformations of terrestrial crust in the region. They are also associated with tectonic constraints of the study area. The usefulness of repeated measurements of these elements, the estimate of displacements and the determination of their temporal rates is indisputable. Indeed, sismo-tectonique studies allow a good knowledge of the of earthquake processes, their frequency their amplitude and even of their prediction in the world in general and in Moroccan area especially. They allow also contributing to guarantee more security for all most important management projects, as projects of building great works (dams, bridges, nuclear centrals). And also as preliminary study, for the most important joint-project between Europe and Africa through the Strait of Gibraltar. For our application, 23 GPS monitoring stations under the ITRF2000 reference frame are chosen in Eurasian and African plates. The sites are located around the Western Mediterranean and especially on Morocco. Exploiting parameters of positions and dispersions of these stations within the 1997-2003 period, the motion and the interaction types of interaction between African and Eurasian tectonic plates can be estimated. Similarly, the crustal dynamic parameters of tension of these sites will be computed. The time occupation on repeated observations sites is at least 72 hours. The measurements are continuous on permanent stations. The precise ephemerides are used in GPS computations. The post-treatments are done using commercial and scientific softwares. The coordinates obtained for two consecutive periods to and t within a period of 8 years will be used by programs established for this purpose to estimate crustal dynamic parameters of tension as well as to evaluate the appropriate movements. Even crustal dynamic parameters will be determined on each sites of the GPS-Geodynamics network, whose interest of seismic investigations is very important. This will allow best knowledge of substantial seismic activities of the surrounding zones. It can be deduced by measuring the motions and their parameter tensions using GPS. These estimations will contribute on the earthquake prediction by supervising the strain accumulation and its release in the active areas. For the geodetically aspect the GPS-Geodynamics sites computed in the ITRF frame can be used with other similar ounces' of Africa country and some well selected and convenient IGS, EUREF stations..to determine first the NAFREF and the AFRER frames.

Improved Data Access From the Northern California Earthquake Data Center

NASA Astrophysics Data System (ADS)

Neuhauser, D.; Oppenheimer, D.; Zuzlewski, S.; Klein, F.; Jensen, E.; Gee, L.; Murray, M.; Romanowicz, B.

2002-12-01

The NCEDC is a joint project of the UC Berkeley Seismological Laboratory and the USGS Menlo Park to provide a long-term archive and distribution center for geophysical data for northern California. Most data are available via the Web at http://quake.geo.berkeley.edu and research accounts are available for access to specialized datasets. Current efforts continue to expand the available datasets, enhance distribution methods, and to provide rapid access to all datasets. The NCEDC archives continuous and event-based seismic and geophysical time-series data from the BDSN, the USGS NCSN, the UNR Seismic Network, the Parkfield HRSN, and the Calpine/Unocal Geysers network. In collaboration with the USGS, the NCEDC has archived a total of 887 channels from 139 sites of the "USGS low-frequency" geophysical network (UL), including data from strainmeters, creep meters, magnetometers, water well levels, and tiltmeters. There are 336 active continuous data channels that are updated at the NCEDC on a daily basis. Geodetic data from the BARD network of over 40 continuously recording GPS sites are archived at the NCEDC in both raw and RINEX format. The NCEDC is the primary archive for survey-mode GPS and other geodetic data collected in northern California by the USGS, universities, and other agencies. All of the BARD data and GPS data archived from USGS Menlo Park surveys are now available through the GPS Seamless Archive Centers (GSAC), and by FTP directly from the NCEDC. Virtually all time-series data at the NCEDC are now available in SEED with complete instrument responses. Assembling, verifying, and maintaining the response information for these networks is a huge task, and is accomplished through the collaborative efforts of the NCEDC and the contributing agencies. Until recently, the NCSN waveform data were available only through research accounts and special request methods due to incomplete instrument responses. In the last year, the USGS compiled the necessary descriptions for for both historic and current NCSN instrumentation. The NCEDC and USGS jointly developed a procedure to create and maintain the hardware attributes and instrument responses at the NCEDC for the 3500 NCSN channels. As a result, the NCSN waveform data can now be distributed in SEED format. The NCEDC provides access to waveform data through Web forms, email requests, and programming interfaces. The SeismiQuery Web interface provides information about data holdings. NetDC allows users to retrieve inventory information, instrument responses, and waveforms in SEED format. STP provides both a Web and programming interface to retrieve data in SEED or other user-friendly formats. Through the newly formed California Integrated Seismic Network, we are working with the SCEDC to provide unified access to California earthquake data.

AAPSilver System Performance Validation

DTIC Science & Technology

2012-12-01

10 APPENDIX A. NATIONAL GEODETIC SURVEY FORWARD OUTPUT FOR BPP ALPHA ... A-1...APPENDIX B. NATIONAL GEODETIC SURVEY FORWARD OUTPUT FOR BPP BRAVO ...B-1 APPENDIX C. NATIONAL GEODETIC SURVEY FORWARD OUTPUT FOR BPP CHARLIE...SURVEY FORWARD OUTPUT FOR BPP DELTA ... D-1 APPENDIX E. NATIONAL GEODETIC SURVEY FORWARD OUTPUT FOR BPP ECHO ......E-1 AAPSilver System Performance

Operational aspects of CASA UNO '88-The first large scale international GPS geodetic network

NASA Technical Reports Server (NTRS)

Neilan, Ruth E.; Dixon, T. H.; Meehan, Thomas K.; Melbourne, William G.; Scheid, John A.; Kellogg, J. N.; Stowell, J. L.

1989-01-01

For three weeks, from January 18 to February 5, 1988, scientists and engineers from 13 countries and 30 international agencies and institutions cooperated in the most extensive GPS (Global Positioning System) field campaign, and the largest geodynamics experiment, in the world to date. This collaborative eperiment concentrated GPS receivers in Central and South America. The predicted rates of motions are on the order of 5-10 cm/yr. Global coverage of GPS observations spanned 220 deg of longitude and 125 deg of latitude using a total of 43 GPS receivers. The experiment was the first civilian effort at implementing an extended international GPS satellite tracking network. Covariance analyses incorporating the extended tracking network predicted significant improvement in precise orbit determination, allowing accurate long-baseline geodesy in the science areas.

Current status of the EPOS WG4 - GNSS and Other Geodetic Data

NASA Astrophysics Data System (ADS)

Fernandes, Rui; Bastos, Luisa; Bruyninx, Carine; D'Agostino, Nicola; Dousa, Jan; Ganas, Athanassios; Lidberg, Martin; Nocquet, Jean-Mathieu

2014-05-01

WG4 - "EPOS Geodetic Data and Other Geodetic Data" is the Working Group of the EPOS project in charge of defining and preparing the integration of the existing Pan-European Geodetic Infrastructures that will support European Geosciences, which is the ultimate goal of the EPOS project. The WG4 is formed by representatives of the participating EPOS countries (23) but it is also open to the entire geodetic community. In fact, WG4 also already includes members from countries that formally are not integrating EPOS in this first step. The geodetic component of EPOS (WG4) is dealing essentially with Research Infrastructures focused on continuous operating GNSS (cGNSS) in the current phase. The option of concentrating the efforts on the presently most generalized geodetic tool supporting research on Solid Earth was decided in order to optimize the existing resources. Nevertheless, WG4 will continue to pursue the development of tools and methodologies that permit the access of the EPOS community to other geodetic information (e.g., gravimetry). Furthermore, although the focus is on Solid Earth applications, other research and technical applications (e.g., reference frames, meteorology, space weather) can also benefit from the efforts of WG4 EPOS towards the optimization of the geodetic resources in Europe. We will present and discuss the plans for the implementation of the thematic and core services (TCS) for geodetic data within EPOS and the related business plan. We will focus on strategies towards the implementation of the best solutions that will permit to the end-users, and in particular geo-scientists, to access the geodetic data, derived solutions, and associated metadata using transparent and uniform processes. Five pillars have been defined proposed for the TCS: Dissemination, Preservation, Monitoring, and Analysis of geodetic data plus the Support and Governance Infrastructure. Current proposals and remaining open questions will be discussed.

Future global SLR network evolution and its impact on the terrestrial reference frame

NASA Astrophysics Data System (ADS)

Kehm, Alexander; Bloßfeld, Mathis; Pavlis, Erricos C.; Seitz, Florian

2018-06-01

Satellite laser ranging (SLR) is an important technique that contributes to the determination of terrestrial geodetic reference frames, especially to the realization of the origin and the scale of global networks. One of the major limiting factors of SLR-derived reference frame realizations is the datum accuracy which significantly suffers from the current global SLR station distribution. In this paper, the impact of a potential future development of the SLR network on the estimated datum parameters is investigated. The current status of the SLR network is compared to a simulated potential future network featuring additional stations improving the global network geometry. In addition, possible technical advancements resulting in a higher amount of observations are taken into account as well. As a result, we find that the network improvement causes a decrease in the scatter of the network translation parameters of up to 24%, and up to 20% for the scale, whereas the technological improvement causes a reduction in the scatter of up to 27% for the translations and up to 49% for the scale. The Earth orientation parameters benefit by up to 15% from both effects.

Resolution testing and limitations of geodetic and tsunami datasets for finite fault inversions along subduction zones

NASA Astrophysics Data System (ADS)

Williamson, A.; Newman, A. V.

2017-12-01

Finite fault inversions utilizing multiple datasets have become commonplace for large earthquakes pending data availability. The mixture of geodetic datasets such as Global Navigational Satellite Systems (GNSS) and InSAR, seismic waveforms, and when applicable, tsunami waveforms from Deep-Ocean Assessment and Reporting of Tsunami (DART) gauges, provide slightly different observations that when incorporated together lead to a more robust model of fault slip distribution. The merging of different datasets is of particular importance along subduction zones where direct observations of seafloor deformation over the rupture area are extremely limited. Instead, instrumentation measures related ground motion from tens to hundreds of kilometers away. The distance from the event and dataset type can lead to a variable degree of resolution, affecting the ability to accurately model the spatial distribution of slip. This study analyzes the spatial resolution attained individually from geodetic and tsunami datasets as well as in a combined dataset. We constrain the importance of distance between estimated parameters and observed data and how that varies between land-based and open ocean datasets. Analysis focuses on accurately scaled subduction zone synthetic models as well as analysis of the relationship between slip and data in recent large subduction zone earthquakes. This study shows that seafloor deformation sensitive datasets, like open-ocean tsunami waveforms or seafloor geodetic instrumentation, can provide unique offshore resolution for understanding most large and particularly tsunamigenic megathrust earthquake activity. In most environments, we simply lack the capability to resolve static displacements using land-based geodetic observations.

Hazard estimation deduced from GPS and seismic data of Egypt

NASA Astrophysics Data System (ADS)

Sayed Mohamed, Abdel-Monem

Egypt rapidly growing development is accompanied by increasing levels of standard living particular in its urban areas. However, there is a limited experience in quantifying the sources of risk management in Egypt and in designing efficient strategies to keep away serious impacts of earthquakes. From the historical point of view and recent instrumental records, there are some seismo-active regions in Egypt, where some significant earthquakes had occurred in different places. The special tectonic features in Egypt: Aswan, Greater Cairo, Red Sea and Sinai Peninsula regions are the territories of a high seismic risk, which have to be monitored by up-to date technologies. The investigations of the seismic events and interpretations led to evaluate the seismic hazard for disaster prevention and for the safety of the dense populated regions and the vital national projects as the High Dam. In addition to the monitoring of the recent crustal movements, the most powerful technique of satellite geodesy GPS are used where geodetic networks are covering such seismo-active regions. The results from the data sets are compared and combined in order to determine the main characteristics of the deformation and hazard estimation for specified regions. The final compiled output from the seismological and geodetic analysis threw lights upon the geodynamical regime of these seismo-active regions and put Aswan and Greater Cairo under the lowest class according to horizontal crustal strains classifications. This work will serve a basis for the development of so-called catastrophic models and can be further used for catastrophic risk management. Also, this work is trying to evaluate risk of large catastrophic losses within the important regions including the High Dam, strategic buildings and archeological sites. Studies on possible scenarios of earthquakes and losses are a critical issue for decision making in insurance as a part of mitigation measures.

Paleomagnetic Quantification of Neogene Block Rotations within an Active Transtensional Plate Boundary, Baja California, Mexico

NASA Astrophysics Data System (ADS)

Weber, J.; Umhoefer, P. J.; Pérez Venzor, J. A.; Bachtadse, V.

2009-12-01

Compared to oceanic plate boundaries which are generally narrow zones of deformation, continental plate boundaries appear as widespread areas with complex and poorly understood kinematics. Motion of crustal blocks within these “diffuse plate boundaries” causes rather small-scale lithospheric deformation within the boundary zone, while the main plates behave more rigid. Complex deformation patterns of interacting terranes separated by a variety of active faults are the consequence. To study the dynamic implications of boundary zone deformation, the southern part of the Baja California peninsula, Mexico (Baja) has been chosen as target for a detailed paleomagnetic study. In combination with geodetic measurements it is tried to characterize rigid block rotations and temporal changes in rotation rates. Up to now, little paleomagnetic work directed toward vertical axis rotations has been done in Baja California, despite its location in a major active transtensional zone. To address this problem, a total of 501 cores from 63 sites in the southern part of Baja - including sites on San José Island, San Francisco Island and Cerralvo Island - has been taken from volcanic and sedimentary rocks covering the last 25 million years in time. The analysis of paleomagnetic declinations and comparison to coeval data from North America and stable areas of Baja California allow evaluating the long-term kinematics of the region and the effects of oblique-rifting in the Gulf of California to the east. Nearly all sampled sites indicate vertical axis rotation up to 30-40 degrees with an average of about 20-25 degrees. Depending on the location these rotations have been either clockwise or counter-clockwise and are correlated with the opening of the Gulf of California and the translation of the Baja California peninsula to the North. Results of the paleomagnetic investigation are compared to geodetic data of the last few years in order to address the problem how strain is partitioned within a complex network of faults and how rates of rotation change with time.

Implementation of CGPS at Estartit, Ibiza and Barcelona harbours for sea level monitoring

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J. J.; Ortiz Castellon, M.; Martinez-Garcia, M.; Perez, B.; Bosch, E.; Termens, A.; Martinez de Oses, X.

2009-12-01

The determination of global and regional mean sea level variations with accura-cies better than 1 mm/yr is a critical problem, the resolution of which is central to the current debate on climate change and its impact on the environment. Highly accurate time series from both satellite altimetry and tide gauges are needed. Measuring the sea surface height with in-situ tide gauges and GPS receivers pro-vides an efficient way to control the long term stability of the radar altimeters and other applications as the vertical land motion and studies of sea level change. L’Estartit tide gauge is a classical floating tide gauge set up in l’Estartit harbour (NE Spain) in 1990. Data are taken in graphics registers from which each two hours the mean value is recorded in an electronic support and delivered to the Permanent Service for Mean Sea level (PSMSL). Periodic surveying campaigns along the year are carried out for monitoring possible vertical movement of the geodetic benchmark adjacent to the tide gauge. Puertos del Estado (Spanish Harbours) installed the tide gauge station at Ibiza har-bour in January 2003 and a near GPS reference station. The station belongs to the REDMAR network, composed at this moment by 21 stations distributed along the whole Spanish waters, including also the Canary islands (http://www.puertos.es). The tide gauge also belongs to the ESEAS (European Sea Level) network. A description of the actual infrastructure at Ibiza, Barcelona and l’Estartit har-bours is presented.The main objective is the implementation of these harbours as a precise geodetic areas for sea level monitoring and altimeter calibration. Actually is a CGPS with a radar tide gauge from Puertos del Estado and a GPS belonging to Puerto de Barcelona. A precise levelling has been made by the Cartographic Insti-tute of Catalonia, ICC. The instrumentation of sea level measurements has been improved by providing the Barcelona site with a radar tide gauge Datamar 3000C device and a Thales Navigation Internet-Enabled GPS Continuous Geodetic Ref-erence Station (iCGRS) with a choke ring antenna, located at the EPSEB of the Technical University of Catalonia, UPC. It is intended that the overall system will constitute a CGPS Station of the ESEAS and TIGA networks.

Plate tectonics and crustal deformation around the Japanese Islands

NASA Technical Reports Server (NTRS)

Hashimoto, Manabu; Jackson, David D.

1993-01-01

We analyze over a century of geodetic data to study crustal deformation and plate motion around the Japanese Islands, using the block-fault model for crustal deformation developed by Matsu'ura et al. (1986). We model the area including the Japanese Islands with 19 crustal blocks and 104 faults based on the distribution of active faults and seismicity. Geodetic data are used to obtain block motions and average slip rates of faults. This geodetic model predicts that the Pacific plate moves N deg 69 +/- 2 deg W at about 80 +/- 3 mm/yr relative to the Eurasian plate which is much lower than that predicted in geologic models. Substantial aseismic slip occurs on the subduction boundaries. The block containing the Izu Peninsula may be separated from the rigid part of the Philippine Sea plate. The faults on the coast of Japan Sea and the western part of the Median Tectonic Line have slip rates exceeding 4 mm/yr, while the Fossa Magna does not play an important role in the tectonics of the central Japan. The geodetic model requires the division of northeastern Japan, contrary to the hypothesis that northeastern Japan is a part of the North American plate. Owing to rapid convergence, the seismic risk in the Nankai trough may be larger than that of the Tokai gap.

Using GPS and leveling data in local precise geoid determination and case study

NASA Astrophysics Data System (ADS)

Erol, B.; Çelik, R. N.; Erol, S.

2003-04-01

As an important result of developments in high technology, satellite based positioning system has become to use in geodesy and surveying professions. These developments made the measurement works more accurate, more practical and more economic. Today, one of the most recent used satellite based positioning system is GPS (Global Positioning System) and it serves to a very wide range of geodetic applications from monitoring earth crustal deformations till building the basis for a GIS (Geographical Information Systems). The most efficient way to utilize GPS measurement system for mentioned aims is having a reliable geodetic infrastructure in working area. Geodetic infrastructure is a extraterrestrial and time system and involved 4D geodetic reference networks. The forth element of mentioned geodetic reference system is time because having an accurate and reliable geodetic infrastructure is needed to up-date according to physical realities of the region. By the help of a well designed geodetic infrastructure accurate and reliable coordinates of a point can be generated economically every time in a global and up-to-date system. Geoid is one of the important parts of a geodetic infrastructure. As it is well known, geoid is the equipotential surface of the Earth's gravity field which best fits, in a least squares sense, global mean sea level and it is reference for physical height systems like orthometric and normal heights. In the most of the applications, vertical position of a point is expressed with orthometric or normal height. Orthometric or normal height is a physical concept and gives vertical position of a point uniquely. On the other hand, vertical position of a point is derived in a geometrical system according to GPS measurements. GPS datum is WGS84 and in this system, an ellipsoidal height of a point is calculated according to WGS84 ellipsoid. So, it is an necessity to transform the ellipsoidal heights to orthometric heights and this procedure is managed with the fundamental mathematical equation; N=h-H. In the equation, "h" is the ellipsoidal height of a point P, "H" is the orthometric height of the same point and "N" is "geoid undulation" value. Normally, "H" orthometric height derived from leveling measurements but these measurements are tiring applications. So, while having a geoid model in the region as the essential part of geodetic infrastructure, number leveling measurements can be reduced from the procedure and by this way time and labor is saved. Geoid determination is modeling of the data in such a way that geoid height can be obtained digital or analog at a point whose horizontal position is known. Geoid models can be developed for local, regional or global regions. Using satellite techniques, especially GPS, in geodetic measurements are increased importance of geoid. Because geoid is a natural tie between high precision geodetic coordinates and coordinates which obtained from satellites. There are several geoid determination methods according to used data and models. GPS/Leveling method, which is also known as geometric method, is one of these methods. This method is appropriate for local precise geoid determination in respectively small areas. In this paper, it is going to be given information about GPS/Leveling geoid determination method and mathematical models, which are used in geoid determination with this method. And Izmir local geoid model will be presented as a case study. Izmir is one of the west metropolitan cities of Turkey and located near Aegean Sea. The topography is extremely rough in the region. There are two different geoid determination studies which were carried out in 1996 and 2001 in Izmir. Both models were accomplished according to GPS/Leveling method. Those two geoid models of Izmir Metropolitan region are investigated in here, the conflict of them were discussed. The relation between distribution of common reference points and differences of geoid undulation values, which are calculated from both models separately, were analyzed and also effects of topography on conflict of both geoid model was investigated. The results of the study and suggestions are going to be given in the paper.

LONG-TERM STABILITY OF THE LOCAL GROUND CONTROL NETWORK AT THE CO-LOCATION SITE OF MEDICINA

NASA Astrophysics Data System (ADS)

Abbondanza, C.; Sarti, P.; Legrand, J.

2009-12-01

ITRF combinations rely on the availability of accurate tie vectors linking reference points of space geodetic techniques. Co-located instruments are assumed to move consistently and no local relative motion is taken into account. Instabilities may degrade the quality of the co-location itself and perturb the result of ITRF combinations. This work aims to determine the stability of the local ground control network at Medicina (Italy) with independent surveying methods. The observatory hosts a co-location between a VLBI telescope and two GPS antennas, MEDI and MSEL. It is located in the Po Plain where thick layers of clays are the prevalent soil characteristics. Hence, provision of long term stability of geodetic monuments is a challenge and monitoring their stability is an issue. MEDI and the VLBI station regularly contribute to the determination of ITRF, while MSEL is part of the EUREF network. A set of five tie vectors observations linking the VLBI and MEDI reference points was acquired between 2001 and 2007. It is our main tool for performing local deformation analysis. Additionally, the GPS time series of MEDI and MSEL were used to cross check and confirm the local instability detected by terrestrial methods. To achieve a rigorous and reliable investigation of the local stability, multi-epoch terrestrial observations were homogeneously processed according to common parameterizations in a consistent reference frame. Similarly, continuous GPS observations from MEDI and MSEL were analysed according to the new EPN reprocessing strategy in order to monitor the short baseline between MEDI and MSEL; to spotlight any change in its length. Both approaches confirm differential motions at the site which can be related to monument instabilities originated by the particularly unfavourable local geological setting and the inapt design of the monuments foundation. The monuments move non homogeneously at rates reaching up to 1.6 mm/year, this value being comparable to intra-plate tectonic deformations. Evidences of relative motion between MEDI and MSEL are found: an annual signal with amplitude ≈1.3 mm is detected along the East component and an 80 weeks signal with amplitude ≈1.1 mm is found along the vertical component of the baseline. The combination of the two independent observing techniques confirms the importance of repeatedly performed terrestrial surveys and the presence of intra-technique co-locations at geodetic sites. Although available, VLBI observations were not considered since we are interested in detecting local relative motions in a very restricted area (100m x 100m) avoiding problems of datum consistencies between different space geodetic techniques. In fact, the combination of technique-specific frames might originate local inconsistencies on station positions due to misalignments of tie vectors in the global reference frame. These inconsistencies might degrade the accuracy of the displacement analysis and can be difficult to deal with.

Local precision nets for monitoring movements of faults and large engineering structures

NASA Technical Reports Server (NTRS)

Henneberg, H. G.

1978-01-01

Along Bocono Fault were installed local high precision geodetic nets to observe the possible horizontal crustal deformations and movements. In the fault area there are few big structures which are also included in the mentioned investigation. In the near future, measurements shall be extended to other sites of Bocono Fault and also to the El Pilar Fault. In the same way and by similar methods high precision geodetic nets are applied in Venezuela to observe the behavior of big structures, as bridges and large dams and of earth surface deformations due to industrial activities.

The changing shapes of active volcanoes: History, evolution, and future challenges for volcano geodesy

USGS Publications Warehouse

Poland, Michael P.; Hamburger, Michael W.; Newman, Andrew V.

2006-01-01

At the very heart of volcanology lies the search for the 'plumbing systems' that form the inner workings of Earth’s active volcanoes. By their very nature, however, the magmatic reservoirs and conduits that underlie these active volcanic systems are elusive; mostly they are observable only through circumstantial evidence, using indirect, and often ambiguous, surficial measurements. Of course, we can infer much about these systems from geologic investigation of materials brought to the surface by eruptions and of the exposed roots of ancient volcanoes. But how can we study the magmatic processes that are occurring beneath Earth’s active volcanoes? What are the geometry, scale, physical, and chemical characteristics of magma reservoirs? Can we infer the dynamics of magma transport? Can we use this information to better forecast the future behavior of volcanoes? These questions comprise some of the most fundamental, recurring themes of modern research in volcanology. The field of volcano geodesy is uniquely situated to provide critical observational constraints on these problems. For the past decade, armed with a new array of technological innovations, equipped with powerful computers, and prepared with new analytical tools, volcano geodesists have been poised to make significant advances in our fundamental understanding of the behavior of active volcanic systems. The purpose of this volume is to highlight some of these recent advances, particularly in the collection and interpretation of geodetic data from actively deforming volcanoes. The 18 papers that follow report on new geodetic data that offer valuable insights into eruptive activity and magma transport; they present new models and modeling strategies that have the potential to greatly increase understanding of magmatic, hydrothermal, and volcano-tectonic processes; and they describe innovative techniques for collecting geodetic measurements from remote, poorly accessible, or hazardous volcanoes. To provide a proper context for these studies, we offer a short review of the evolution of volcano geodesy, as well as a case study that highlights recent advances in the field by comparing the geodetic response to recent eruptive episodes at Mount St. Helens. Finally, we point out a few areas that continue to challenge the volcano geodesy community, some of which are addressed by the papers that follow and which undoubtedly will be the focus of future research for years to come.

Geodetic evidence for continuing tectonic activity of the Carboneras fault (SE Spain)

NASA Astrophysics Data System (ADS)

Echeverria, Anna; Khazaradze, Giorgi; Asensio, Eva; Masana, Eulalia

2015-11-01

The Carboneras fault zone (CFZ) is a prominent onshore-offshore strike-slip fault that forms part of the Eastern Betic Shear Zone (EBSZ), located in SE Spain. In this work, we show for the first time, the continuing tectonic activity of the CFZ and quantify its geodetic slip-rates using continuous and campaign GPS observations conducted during the last decade. We find that the left-lateral motion dominates the kinematics of the CFZ, with a strike-slip rate of 1.3 ± 0.2 mm/yr along the N48° direction. The shortening component is significantly lower and poorly constrained. Recent onshore and offshore paleoseismic and geomorphic results across the CFZ suggest a minimum Late Pleistocene to present-day strike-slip rate of 1.1 mm/yr. Considering the similarity of the geologic and geodetic slip rates measured at different points along the fault, the northern segment of the CFZ must have been slipping approximately at a constant rate during the Quaternary. Regarding the eastern Alpujarras fault zone corridor (AFZ), located to the north of the CFZ, our GPS measurements corroborate that this zone is active and exhibits a right-lateral motion. These opposite type strike-slip motion across the AFZ and CFZ is a result of a push-type force due to Nubia and Eurasia plate convergence, which, in turn, causes the westward escape of the block bounded by these two fault zones.

The Telecommunications and Data Acquisition

NASA Technical Reports Server (NTRS)

Renzetti, N. A. (Editor)

1981-01-01

Progress in the development and operations of the Deep Space Network is reported including developments in Earth based radio technology as applied to other research programs. These programs include application of radio interferometry at microwave frequencies to geodetic measurements and geodynamics, use of deep space stations individually and in pairs as an interferometer by radio astronomers for astrophysics research by direct observations of radio sources, and radio search for extraterrestrial intelligence in the microwave region of the electromagnetic spectrum.

Evaluation of the Time and Frequency Transfer Capabilities of a Network of GNSS Receivers Located in Timing Laboratories

DTIC Science & Technology

2009-11-01

metrology, different techniques are used for time and frequency transfer, basically TWSTFT (Two-Way Satellite Time and Frequency Transfer), GPS CV (Common...traditional GPS/GLONASS CV/AV receivers and TWSTFT equipment. Time and frequency transfer using GPS code and carrier-phase is an important...or mixing GPS geodetic results with other independent techniques, such as the TWSTFT . 41 st Annual Precise Time and Time Interval (PTTI

Analysis of the geodetic residuals as differences between geodetic and sum of the atmospheric and ocean excitation of polar motion

NASA Astrophysics Data System (ADS)

Kolaczek, B.; Pasnicka, M.; Nastula, J.

2012-12-01

Up to now studies of geophysical excitation of polar motion containing AAM (Atmospheric Angular Momentum), OAM (Oceanic Angular Momentum) and HAM (Hydrological Angular Momentum) excitation functions of polar motion have not achieved the total agreement between geophysical and determined geodetic excitation (GAM, Geodetic AngularMomentum) functions of polar motion...

Near Real-Time Processing and Archiving of GPS Surveys for Crustal Motion Monitoring

NASA Astrophysics Data System (ADS)

Crowell, B. W.; Bock, Y.

2008-12-01

We present an inverse instantaneous RTK method for rapidly processing and archiving GPS data for crustal motion surveys that gives positional accuracy similar to traditional post-processing methods. We first stream 1 Hz data from GPS receivers over Bluetooth to Verizon XV6700 smartphones equipped with Geodetics, Inc. RTD Rover software. The smartphone transmits raw receiver data to a real-time server at the Scripps Orbit and Permanent Array Center (SOPAC) running RTD Pro. At the server, instantaneous positions are computed every second relative to the three closest base stations in the California Real Time Network (CRTN), using ultra-rapid orbits produced by SOPAC, the NOAATrop real-time tropospheric delay model, and ITRF2005 coordinates computed by SOPAC for the CRTN stations. The raw data are converted on-the-fly to RINEX format at the server. Data in both formats are stored on the server along with a file of instantaneous positions, computed independently at each observation epoch. The single-epoch instantaneous positions are continuously transmitted back to the field surveyor's smartphone, where RTD Rover computes a median position and interquartile range for each new epoch of observation. The best-fit solution is the last median position and is available as soon as the survey is completed. We describe how we used this method to process 1 Hz data from the February, 2008 Imperial Valley GPS survey of 38 geodetic monuments established by Imperial College, London in the 1970's, and previously measured by SOPAC using rapid-static GPS methods in 1993, 1999 and 2000, as well as 14 National Geodetic Survey (NGS) monuments. For redundancy, each monument was surveyed for about 15 minutes at least twice and at staggered intervals using two survey teams operating autonomously. Archiving of data and the overall project at SOPAC is performed using the PGM software, developed by the California Spatial Reference Center (CSRC) for the National Geodetic Survey (NGS). The importation of raw receiver data, site metadata and antenna height information is performed using PGM client software running on the same PDA running RTD Rover or laptop, and uploaded to the PGM server where the raw data are converted to RINEX format. The campaign information is then published online, where all of the campaign information can be accessed such as start and stop times, equipment information, RINEX and solution SINEX files, observer information and baseline information for network adjustments.

Implementation of Barcelona, L'estartit and Ibiza Sites for Altimeter Calibration

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J. J.; Gili, J.; Lopez, R.; Tapia, A.; Bosch, E.; Perez, B.; Pros, F.

2012-12-01

A marine campaign to compute the sea surface data along the Spanish Mediterranean coastline and Balearic Islands is being prepared for 2013. Jason-2 (period ~10 days) and Saral/AltiKa (period of 35 days and expected launch in 2012) altimetric data and on-board GPS data will be used. Many GPS Buoy sessions along the ship route will be performed.Sea height estimates (instantaneous and mean sea levels) will be compared. Recently some geodetic improvements has been made in specific coastal spanish sites in the NW Mediterranean Sea for monitoring sea level. The goal is to maintain and improve the quality of the observation of the sea level change in the three sites. The information is coming from Puertos del Estado www.puertos.es L'Estartit tide gauge has been co-located with geodetic techniques (GPS measurements of XU, Utilitary Network, and XdA, Levelling Network,) and it is tied to the SPGIC (Integrated Geodetic Positioning System of Catalonia) project of the Cartographic Institute of Catalunya (ICC). In the past three calibration campaigns for Topex/Poseidon and Jason-1 in March 1999, August 2000 and July 2002 near Cape of Begur. At Barcelona harbour there is one MIROS radar tide gauge belonging to Puertos del Estado (Spanish Harbours).The radar sensor is over the water surface, on a L-shaped structure which elevates it a few meters above the quay shelf. 1-min data are transmitted to the ENAGAS Control Center by cable and then sent each 1 min to Puertos del Estado by e-mail. The information includes wave forescast (mean period, significant wave height, sea level, etc.This sensor also measures agitation and sends wave parameters each 20 min. There is a GPS station Leica Geosystems GRX1200 GG Pro and antenna 1202. Bathymetric campaigns inside the harbour have been made. At Ibiza site new measurements and levelling between the GPS reference station and a Radar MIROS, both from Puertos del Estado, has been made recently. A calibration campaign for Jason-1 was made in June 2003 in the Ibiza area, main calibration site. The presentation is directed to the description of the actual situation of the geodetic infrastructure of Barcelona, l'Estartit sites for sea level determination and complementing Ibiza site for a new altimeter calibration campaign of Jason-2 and Saral/AltiKa satellites to be made in 2013. Specifications of the new marine calibration campaign will be presented.

Fifty years of levelling measurements at Askja volcano, Iceland: New Bayesian interpretations of a unique dataset

NASA Astrophysics Data System (ADS)

Barnie, Talfan; Sigmundsson, Freysteinn; Sturkell, Erik

2017-04-01

The year 2016 marks the 50th anniversary of the start of geodetic levelling surveys at Askja volcano in the Northern Volcanic Zone of Iceland. Askja has produced frequent basaltic fissural eruptions and rarer silicic caldera forming eruptions during the Holocene, the most recent of each type in 1961 and 1875 respectively. The potential for widespread disruption from larger eruptions and the popularity of the site with tourists makes Askja an important target for observation. Geodetic monitoring started in 1966 with the installation of a 12 station survey line on the 1961 lava flow, which provided a stable, extensive surface close to the putative source of magma. This was infilled and extended over the following two decades to give a finished levelling line of 35 stations spaced approximately 50 m apart (Tryggvason, Nordic Volcanological Institute, 1989). With the exception of the period 1972 to 1983, this line has been surveyed every year, providing a unique record of post eruptive deformation at a spreading rift segment capable of capturing magma motions at depth and any potential recharging in anticipation of future activity. The levelling has so far revealed that after an initial period of complicated inflations and deflations the volcano settled into a pattern of slowly decaying deflation from 1983 onwards (Sturkell and Sigmundsson, JGR, 105, 2000), a pattern that has been confirmed by newer geodetic techniques as they have become available (e.g. Pagli et al., JVGR, 152, 2005). The strength of the levelling data at Askja is its long time span, high accuracy and same measurement type over a period of 50 years. However, the small extent of the levelling line limits the power of the network to resolve changes in the magma plumbing system and requires the addition of constraints from other sources. This lends itself to Bayesian modelling techniques where assumptions are made explicit as priors and uncertainties in retrieved parameters can be comprehensibly modelled. Here we present a Bayesian inversion of the full dataset using the Stan probabilistic programming language that allows us to test a range of models of subsurface pressure changes and magma motions at depth.

High-accuracy local positioning network for the alignment of the Mu2e experiment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hejdukova, Jana B.

This Diploma thesis describes the establishment of a high-precision local positioning network and accelerator alignment for the Mu2e physics experiment. The process of establishing new network consists of few steps: design of the network, pre-analysis, installation works, measurements of the network and making adjustments. Adjustments were performed using two approaches. First is a geodetic approach of taking into account the Earth’s curvature and the metrological approach of a pure 3D Cartesian system on the other side. The comparison of those two approaches is performed and evaluated in the results and compared with expected differences. The effect of the Earth’s curvaturemore » was found to be significant for this kind of network and should not be neglected. The measurements were obtained with Absolute Tracker AT401, leveling instrument Leica DNA03 and gyrotheodolite DMT Gyromat 2000. The coordinates of the points of the reference network were determined by the Least Square Meth od and the overall view is attached as Annexes.« less

NATIONAL CARTOGRAPHIC INFORMATION CENTER: AN INFORMATION RESOURCE ON MAPPING PRODUCTS FOR THE NATION.

USGS Publications Warehouse

Stevens, Alan R.

1985-01-01

Since its inception in 1974 the National Cartographic Information Center (NCIC), US Geological Survey, has rapidly developed to become a focal point for providing information on the availability of cartographic data, including maps/charts, aerial photographs, satellite imagery, geodetic control, digital mapping data, map materials and related cartographic products. In early years NCIC concentrated its efforts on encoding and entering several major National Mapping Division record collections into its systems. NCIC is now stressing the acquisition of data from sources outside the National Mapping Division, including 37 Federal agencies and more than a thousand State and private institutions. A critical review has recently been conducted by NCIC of its systems with the aim of improving its efficiency and levels of operation. Several activities which resulted include improving its existing networks, refinement of digital data distribution, study of new storage media and related projects.

Geodetic, Geologic and Seismic Interdisciplinary Research of Tectonically Caused Movements in the Wider Area of the City of Zagreb

NASA Astrophysics Data System (ADS)

Dapo, A.; Pribicevic, B.; Herak, M.; Prelogovic, E.

2012-04-01

Since the last great earthquake in 1880 which shook the Zagreb area with IX° MCS, tectonic movements and models of numerous Zagreb faults have been the focal point of Croatian geologists, seismologists and in the last 15 years also geodetic scientists, who all have been working in the scope of their scientific branches on bringing the light to the tectonic mechanisms in the wider Zagreb area. Since it is tectonically very active area and being the Capitol city of the Croatia with very high population density it is of utmost importance to understand those mechanisms and to according to them find the best possible measures for protecting people and valuables. Best results are certainly going to be achieved through the interdisciplinary approach. That is why this paper presents first interdisciplinary results from geodetic, geologic and seismic researches and their contribution to the collective knowledge about tectonic movements in the wider area of the City of Zagreb.

Global reference frame: Intercomparison of results (SLR, VLBI and GPS)

NASA Technical Reports Server (NTRS)

Ma, Chopo; Watkins, Michael M.; Heflin, M.

1994-01-01

The terrestrial reference frame (TRF) is realized by a set of positions and velocities derived from a combination of the three space geodetic techniques, SLR, VLBI and GPS. The standard International TRF is constructed by the International Earth Rotation Service in such a way that it is stable with time and the addition of new data. An adopted model for overall plate motion, NUVEL-1 NNR, defines the conceptual reference frame in which all the plates are moving. In addition to the measurements made between reference points within the space geodetic instruments, it is essential to have accurate, documented eccentricity measurements from the instrument reference points to ground monuments. Proper local surveys between the set of ground monuments at a site are also critical for the use of the space geodetic results. Eccentricities and local surveys are, in fact, the most common and vexing sources of error in the use of the TRF for such activities as collocation and intercomparison.

Local topography increasingly influences the mass balance of a retreating cirque glacier

USGS Publications Warehouse

Florentine, Caitlyn; Harper, Joel T.; Fagre, Daniel B.; Moore, Johnnie; Peitzsch, Erich H.

2018-01-01

Local topographically driven processes – such as wind drifting, avalanching, and shading – are known to alter the relationship between the mass balance of small cirque glaciers and regional climate. Yet partitioning such local effects from regional climate influence has proven difficult, creating uncertainty in the climate representativeness of some glaciers. We address this problem for Sperry Glacier in Glacier National Park, USA, using field-measured surface mass balance, geodetic constraints on mass balance, and regional climate data recorded at a network of meteorological and snow stations. Geodetically derived mass changes during 1950–1960, 1960–2005, and 2005–2014 document average mass change rates during each period at −0.22 ± 0.12, −0.18 ± 0.05, and −0.10 ± 0.03 m w.e. yr−1, respectively. A correlation of field-measured mass balance and regional climate variables closely (i.e., within 0.08 m w.e. yr−1) predicts the geodetically measured mass loss from 2005 to 2014. However, this correlation overestimates glacier mass balance for 1950–1960 by +1.20 ± 0.95 m w.e. yr−1. Our analysis suggests that local effects, not represented in regional climate variables, have become a more dominant driver of the net mass balance as the glacier lost 0.50 km2 and retreated further into its cirque.

Initial Results Obtained with the First TWIN VLBI Radio Telescope at the Geodetic Observatory Wettzell

PubMed Central

Schüler, Torben; Kronschnabl, Gerhard; Plötz, Christian; Neidhardt, Alexander; Bertarini, Alessandra; Bernhart, Simone; la Porta, Laura; Halsig, Sebastian; Nothnagel, Axel

2015-01-01

Geodetic Very Long Baseline Interferometry (VLBI) uses radio telescopes as sensor networks to determine Earth orientation parameters and baseline vectors between the telescopes. The TWIN Telescope Wettzell 1 (TTW1), the first of the new 13.2 m diameter telescope pair at the Geodetic Observatory Wettzell, Germany, is currently in its commissioning phase. The technology behind this radio telescope including the receiving system and the tri-band feed horn is depicted. Since VLBI telescopes must operate at least in pairs, the existing 20 m diameter Radio Telescope Wettzell (RTW) is used together with TTW1 for practical tests. In addition, selected long baseline setups are investigated. Correlation results portraying the data quality achieved during first initial experiments are discussed. Finally, the local 123 m baseline between the old RTW telescope and the new TTW1 is analyzed and compared with an existing high-precision local survey. Our initial results are very satisfactory for X-band group delays featuring a 3D distance agreement between VLBI data analysis and local ties of 1 to 2 mm in the majority of the experiments. However, S-band data, which suffer much from local radio interference due to WiFi and mobile communications, are about 10 times less precise than X-band data and require further analysis, but evidence is provided that S-band data are well-usable over long baselines where local radio interference patterns decorrelate. PMID:26263991

Polar Motion Studies and NOAA's Legacy of International Scientific Cooperation: Ukiah and Gaithersburg Latitude Observatories

NASA Astrophysics Data System (ADS)

Caccamise, D. J., II; Stone, W. A.

2017-12-01

In 1895, the International Geodetic Association invited the United States Coast and Geodetic Survey (USC&GS) to join in an unprecedented international effort to observe and measure the earth's polar motion. This effort was in response to the American astronomer Seth C. Chandler Jr. announcing his 1891 discovery that the earth's axis of rotation—and hence the direction of true north—wobbles within the earth with a period of about 14 months, varying latitude everywhere on the globe. In 1899, two astro-geodetic observatories were built in Gaithersburg, Maryland and Ukiah, California with three others in Caloforte, Italy; Kitab, Russia (now Uzbekistan); and Mizusawa, Japan. (A sixth station was located and operated at an astronomical observatory in Cincinnati, Ohio until 1916 using instruments loaned by USC&GS). All five observatories were located along the same parallel - approximately 35 degrees - 8 minutes. The observatories were decommissioned in 1982, and subsequently, NOAA deeded the two remaining U.S. observatories to the cities of Gaithersburg and Ukiah. The observatories and adjacent property were to be used as parkland. Both cities have restored the observatories and opened public parks. Recently, Gaithersburg (Ukiah in progress) has had its latitude observatory dedicated as a National Historic Landmark. In 2014-15, the National Geodetic Survey (NGS, the present-day NOAA successor to the USC&GS) loaned the original zenith telescopes to the communities, returning the observatories to their original configuration. The contribution of NOAA observers and the data collected is still important to astronomers and geophysicists and has practical applications in spacecraft navigation and geospatial positioning. This poster will bring to fruition this multiyear effort among partners by providing examples of NOAA's mission and contribution to science, service, and stewardship at both geodetic observatories, through programs and historic exhibits for students and the general public. Results will include an increase in exposure to NOAA's rich and formative heritage as well as its enduring scientific research and other activities. Thus, NOAA's historic heritage and assets of the International Latitude Observatories will be protected and preserved through activities for education, outreach, and tourism.

Comparison between geodetic and oceanographic approaches to estimate mean dynamic topography for vertical datum unification: evaluation at Australian tide gauges

NASA Astrophysics Data System (ADS)

Filmer, M. S.; Hughes, C. W.; Woodworth, P. L.; Featherstone, W. E.; Bingham, R. J.

2018-04-01

The direct method of vertical datum unification requires estimates of the ocean's mean dynamic topography (MDT) at tide gauges, which can be sourced from either geodetic or oceanographic approaches. To assess the suitability of different types of MDT for this purpose, we evaluate 13 physics-based numerical ocean models and six MDTs computed from observed geodetic and/or ocean data at 32 tide gauges around the Australian coast. We focus on the viability of numerical ocean models for vertical datum unification, classifying the 13 ocean models used as either independent (do not contain assimilated geodetic data) or non-independent (do contain assimilated geodetic data). We find that the independent and non-independent ocean models deliver similar results. Maximum differences among ocean models and geodetic MDTs reach >150 mm at several Australian tide gauges and are considered anomalous at the 99% confidence level. These differences appear to be of geodetic origin, but without additional independent information, or formal error estimates for each model, some of these errors remain inseparable. Our results imply that some ocean models have standard deviations of differences with other MDTs (using geodetic and/or ocean observations) at Australian tide gauges, and with levelling between some Australian tide gauges, of ˜ ± 50 mm . This indicates that they should be considered as an alternative to geodetic MDTs for the direct unification of vertical datums. They can also be used as diagnostics for errors in geodetic MDT in coastal zones, but the inseparability problem remains, where the error cannot be discriminated between the geoid model or altimeter-derived mean sea surface.

The State and Development Direction of the Geodetic VLBI Station in Korea

NASA Technical Reports Server (NTRS)

Ju, Hyunhee; Kim, Myungho; Kim, Suchul; Park, Jinsik; Kondo, Tetsuro; Kim, Tuhwan; Oh, Hongjong; Yi, Sangoh

2010-01-01

A permanent geodetic VLBI station with a 22-m diameter antenna will be newly constructed in Korea by the National Geographic Information Institute (NGII) under the project Korea VLBI system for Geodesy (KVG) that aims at maintaining the Korean geodetic datum accurately on the International Terrestrial Reference Frame (ITRF). KVG can receive 2, 8, 22, and 43 GHz bands simultaneously in order to conduct geodetic and astronomical VLBI observations with Korea astronomical VLBI stations along with geodetic observations with IVS stations. This simultaneous four-band receiving capability is a unique feature of the KVG system. The KVG has started officially in October 2008. A new geodetic VLBI station will be constructed at Sejong city (about 120 km south of Seoul and about 20 km north-northwest of Daejeon) and construction of all systems will be completed in 2011.

An extended monitoring network for the volcanoes of St. Eustatius and Saba, the Caribbean Netherlands.

NASA Astrophysics Data System (ADS)

de Zeeuw-van Dalfsen, Elske; Sleeman, Reinoud; Evers, Läslo G.

2017-04-01

The volcanoes of the Quill (St. Eustatius) and Mt. Scenery (Saba) are part of the Lesser Antilles volcanic island arc in the West Indies, which hosts seventeen active volcanoes. The last eruptive activity at the Quill occurred 1600-1800 years ago but Mt. Scenery erupted as recent as in 1640. The existence of heated groundwater at St. Eustatius and hot springs at Saba indicate that both the Quill and Mt. Scenery are active, but quiet, rather than extinct. Volcanic hazard is therefore present and monitoring of these volcanoes of utmost importance. Especially considering the fact that Soufrière Hills volcano, at the neighbouring island of Montserrat and of comparable nature to Mt. Scenery, started to erupt in 1995 after 450 years of quietness. Currently, a network of four broadband seismometers is operational at each island. Seismic data are transmitted in real-time to the Royal Netherlands Meteorological Institute (KNMI), where they are (automatically) analysed. We plan to extend this monitoring effort by adding integrated geodetic observations (campaign and continuous GPS, InSAR) and temperature measurements of the hot springs. Furthermore we intend to improve our understanding of the terrain and surface geology by thorough analysis of a TanDEM-X DEM. An improved geophysical characterization of the islands is of great importance both for the population and local governments. These combined efforts will greatly improve the chance to observe the onset and follow the evolution of a future volcanic crisis.

The Earth Viewed as a Deforming Polyhedron: Method and Results

NASA Technical Reports Server (NTRS)

Blewitt, G.; Heflin, M. B.; Vigue, Y.; Zumberge, J. F.; Jefferson, D.; Webb, F. H.

1993-01-01

GPS is quite unlike any other geodetic technique, because we can use it to look at the Earth with high spatial and temporal resolution. For example, the GPS global network provides us with a daily snapshot of the Earth, allowing us to look with high temporal resolution at the motion of sites before, during, and after a large earthquake.The main focus of this paper is to view the Earth as an evolving polyhedron, whose vertices are defined by the GPS sites.

Characterization and Calibration of the 12-m Antenna in Warkworth, New Zealand

NASA Technical Reports Server (NTRS)

Gulyaev, Sergei; Natusch, Tim; Wilson, David

2010-01-01

The New Zealand 12-m antenna is scheduled to start participating in regular IVS VLBI sessions from the middle of 2010. Characterization procedures and results of calibration of the New Zealand 12- m radio telescope are presented, including the main reflector surface accuracy measurement, pointing model creation, and the system equivalent flux density (SEFD) determination in both S and X bands. Important issues of network connectivity, co-located geodetic systems, and the use of the antenna in education are also discussed.

Vertical-deformation, water-level, microgravity, geodetic, water-chemistry, and flow-rate data collected during injection, storage, and recovery tests at Lancaster, Antelope Valley, California, September 1995 through September 1998

USGS Publications Warehouse

Metzger, Loren F.; Ikehara, Marti E.; Howle, James F.

2001-01-01

A series of freshwater injection, storage, and recovery tests were conducted from September 1995 through September 1998 to evaluate the feasibility of artificially recharging ground water in the Lancaster area of the Antelope Valley, California. The tests used two production wells at a well field located in the southern part of the city of Lancaster. Monitoring networks were established at or in the vicinity of the test site to measure vertical deformation of the aquifer system, water-level fluctuations, land-surface deformation, water chemistry, and injection well flow rates during water injection and recovery. Data presented in this report were collected from a dual extensometer; 10 piezometers; 1 barometer; 27 active or abandoned production wells; 31 gravity stations; 124 bench marks; 1 permanent and 1 temporary continuous Global Positioning System (GPS) station; 3 tiltmeters; and 2 electromagnetic flowmeters from September 1995 through September 1998. This report discusses the location and design of the monitoring networks and the methods used to collect and process the data, and presents the data in tables and graphs.

Progress at ROEN - Fortaleza Geodetic Station

NASA Astrophysics Data System (ADS)

Kaufman, Pierre; Macilio Pereira de Lucena, A.; Tateyama, Claudio E.

1999-08-01

This report presents the works developed at ROEN: Radio-Observatorio Espacial do Nordeste, Eusebio near Fortaleza, CE, Brazil, in 1998. Activities were related to observing sessions, major maintenance items, and scientific results obtained.

Geophysical Observations Supporting Research of Magmatic Processes at Icelandic Volcanoes

NASA Astrophysics Data System (ADS)

Vogfjörd, Kristín. S.; Hjaltadóttir, Sigurlaug; Roberts, Matthew J.

2010-05-01

Magmatic processes at volcanoes on the boundary between the European and North American plates in Iceland are observed with in-situ multidisciplinary geophysical networks owned by different national, European or American universities and research institutions, but through collaboration mostly operated by the Icelandic Meteorological Office. The terrestrial observations are augmented by space-based interferometric synthetic aperture radar (InSAR) images of the volcanoes and their surrounding surface. Together this infrastructure can monitor magma movements in several volcanoes from the base of the crust up to the surface. The national seismic network is sensitive enough to detect small scale seismicity deep in the crust under some of the voclanoes. High resolution mapping of this seismicity and its temporal progression has been used to delineate the track of the magma as it migrates upwards in the crust, either to form an intrusion at shallow levels or to reach the surface in an eruption. Broadband recording has also enabled capturing low frequency signals emanating from magmatic movements. In two volcanoes, Eyjafjallajökull and Katla, just east of the South Iceland Seismic Zone (SISZ), seismicity just above the crust-mantle boundary has revealed magma intruding into the crust from the mantle below. As the magma moves to shallower levels, the deformation of the Earth‘s surface is captured by geodetic systems, such as continuous GPS networks, (InSAR) images of the surface and -- even more sensitive to the deformation -- strain meters placed in boreholes around 200 m below the Earth‘s surface. Analysis of these signals can reveal the size and shape of the magma as well as the temporal evolution. At near-by Hekla volcano flanking the SISZ to the north, where only 50% of events are of M>1 compared to 86% of earthquakes in Eyjafjallajökull, the sensitivity of the seismic network is insufficient to detect the smallest seismicity and so the volcano appears less active and deep seismicity has not been detected. Improved seismic station density may improve the resolution of deep processes. Due do Hekla‘s continued expansion, the concentration of the continuous GPS network has been increased around Hekla and a strain meter will be installed by the volcano in 2010. The increased density of geodetic observations is expected to increase the resolution of the depth, volume and geometry of the magma chamber. Before the volcano's latest eruption in 2000, the increased seismicity and deformation signal recorded by the nearest seismic station and strain meter (at 15 km distance) enabled a public warning to be issued of the impending eruption 30 minutes prior to eruption. The additional instrumentation around Hekla is expected to extend the previous advance warning time.

Strain rate orientations near the Coso Geothermal Field

NASA Astrophysics Data System (ADS)

Ogasa, N. T.; Kaven, J. O.; Barbour, A. J.; von Huene, R.

2016-12-01

Many geothermal reservoirs derive their sustained capacity for heat exchange in large part due to continuous deformation of preexisting faults and fractures that permit permeability to be maintained. Similarly, enhanced geothermal systems rely on the creation of suitable permeability from fracture and faults networks to be viable. Stress measurements from boreholes or earthquake source mechanisms are commonly used to infer the tectonic conditions that drive deformation, but here we show that geodetic data can also be used. Specifically, we quantify variations in the horizontal strain rate tensor in the area surrounding the Coso Geothermal Field (CGF) by analyzing more than two decades of high accuracy differential GPS data from a network of 14 stations from the University of Nevada Reno Geodetic Laboratory. To handle offsets in the data, from equipment changes and coseismic deformation, we segment the data, perform a piecewise linear fit and take the average of each segment's strain rate to determine secular velocities at each station. With respect to North America, all stations tend to travel northwest at velocities ranging from 1 to 10 mm/yr. The nearest station to CGF shows anomalous motion compared to regional stations, which otherwise show a coherent increase in network velocity from the northeast to the southwest. We determine strain rates via linear approximation using GPS velocities in Cartesian reference frame due to the small area of our network. Principal strain rate components derived from this inversion show maximum extensional strain rates of 30 nanostrain/a occur at N87W with compressional strain rates of 37nanostrain/a at N3E. These results generally align with previous stress measurements from borehole breakouts, which indicate the least compressive horizontal principal stress is east-west oriented, and indicative of the basin and range tectonic setting. Our results suggest that the CGF represents an anomaly in the crustal deformation field, which may be influenced by the hydrothermal anomaly and possibly by the geothermal reservoir operations as well.

An Introduction to the Tibet cGPS pilot project: TigiCAS

NASA Astrophysics Data System (ADS)

Zhang, Z.; Liu, J.; Galetzka, J.; Avouac, J.; Tapponnier, P.; Zeng, L.; Gan, W.; Shen, Z.; Wang, M.

2007-12-01

The convergence between India and Eurasia is the¡¡prototype of continental collision in action. Compared¡¡to geological history and fault kinematics studies, the present-day, regional pattern of strain-partitioning¡¡is still inadequately known. Among limited geodetic¡¡efforts in the past decade or two, most have been focused¡¡on refining measurements of the current crustal¡¡shortening rate across the Himalaya. The vast region¡¡immediately to the north is sparsely instrumented, with only one continuous GPS station (Lhasa) within¡¡the plateau proper. Campaign stations are few and¡¡ill-positioned, mostly along major roads, providing¡¡poor constraints on present-day slip-rates on individual¡¡active faults. The extant GPS network configuration is thus still insufficient to discriminate between block vs continuum deformation. In November 2006, the¡¡Chinese Academy of Sciences led a pilot program and¡¡installed 6 continuous GPS stations in southern Tibet, crossing the NS-trending normal fault systems and¡¡complementing the Nepal cGPS profiles. We present¡¡here the new sites, preliminary data processing results, and the spatial relationship with ongoing or planned¡¡continuous GPS sites from a couple of other projects. Together with such projects, TigiCAS will provide¡¡a substantial increase in geodetic data in the¡¡Himalayan-Tibet convergent belt in the next few¡¡years, and lead to a better understanding of¡¡contemporary deformation of the region.

Measuring the Heavens to Rule the Territory: Filipe Folque and the Teaching of Astronomy at the Lisbon Polytechnic School and the Modernization of the State Apparatus in Nineteenth Century Portugal

NASA Astrophysics Data System (ADS)

Carolino, Luís Miguel

2012-01-01

This paper focuses on the astronomy teaching at the Lisbon Polytechnic School and its role in building a modern technoscientific state in Portugal during the nineteenth century. It examines particularly the case of Filipe Folque, who taught astronomy and geodesy at the Lisbon Polytechnic from 1837 to 1856, and played a pivotal role in the geodetic survey carried out in the second half of the nineteenth century. As director of the Portuguese Geodetic and Topographical Office, Folque delineated in detail the plan to proceed with the geodetic survey, a plan which involved a significant number of his former students at the Lisbon Polytechnic. Yet, Folque's influence went beyond the geodetic achievement. Folque contributed decisively for shaping the character of astronomy and of the astronomical community in Portugal. In a period in which spherical astronomy raised to the status of an autonomous discipline, Folque became one of the most outstanding proponents of this discipline in Portugal. He conceived a course on spherical astronomy at the Lisbon Polytechnic and published an influential textbook to be adopted as a didactic tool in astronomical classes. By doing so, Folque took active part in a nineteenth century culture of textbooks production, and positively influenced the consolidation and shaping of astronomy as a discipline.

Geometry of the 1954 Fairview Peak-Dixie Valley earthquake sequence from a joint inversion of leveling and triangulation data

USGS Publications Warehouse

Hodgkinson, K.M.; Stein, R.S.; Marshall, G.

1996-01-01

In 1954, four earthquakes greater than Ms=6.0 occurred within a 30-km radius and in a period of 6 months. Elevation and angle changes calculated from repeated leveling and triangulation surveys which span the coseismic period provide constraints on the fault geometries and coseismic slip of the faults which were activated. The quality of the coseismic geodetic data is assessed. Corrections are applied to the leveling data for subsidence due to groundwater withdrawal in the Fallon area, and a rod miscalibration error of 150??30 ppm is isolated in leveling surveys made in 1967. The leveling and triangulation observations are then simultaneously inverted using the single value decomposition (SVD) inversion method to determine fault geometries and coseismic slip. Using SVD, it is possible to determine on which faults slip is resolvable given the data distribution. The faults are found to dip between 50?? and 80?? and extend to depths of 5 to 14 km. The geodetically derived slip values are generally equal to, or greater than, the maximum observed displacement along the surface scarps. Where slip is resolvable the geodetic data indicates the 1954 sequence contained a significant component of right-lateral slip. This is consistent with the N15??W trending shear zone which geodetic surveys have detected in western Nevada. Copyright 1996 by the American Geophysical Union.

Sequence of slow slip events and low frequency earthquakes in the shallow part of the Nankai Trough seismogenic zone observed by seafloor observation network.

NASA Astrophysics Data System (ADS)

Araki, E.; Saffer, D. M.; Kopf, A.; To, A.; Ide, S.; Nakano, M.; Kimura, T.; Machida, Y.

2016-12-01

Seismic behavior of the thrust zone in trench side of the seismically coupled plate interface in the Nankai Trough is poorly understood because shore based seismic and geodetic observation does not have enough sensitivity to detect slow activity in the area. In these years, we constructed dense seafloor observation network in combination with pore-fluid pressure, strain, and seismic sensing in IODP deep boreholes (C0002G and C0010A) and 20+ seafloor broadband seismometers cabled to the observation network called DONET for long-term continuous observation in the To-Nankai area of the Nankai Trough, south of Japan. Analysis of the seismic records from DONET seafloor seismometer and pore-fluid pressure records from the boreholes in the period from Jan. 2011 to Apr. 2016 revealed the activities of the slow slip events (SSE), low frequency tremor (LFT), and very low frequency earthquakes (VLFE) in the observation network, detecting seven sequence of pore-fluid pressure transients in these boreholes representing SSEs and many LFT and VLFEs from seismic records. Some of the SSE sequence accompanies active LFT swarms in the regions offshore of the locked seismogenic zone. Some of the pressure transient initiate precedent to the LFT swarms, as well as some does not accompany obvious LFT activity, as if the SSE occurs "silently", suggesting LFT does not express SSE but LFT seems activated by the SSE. This is also supported by change of SSE pressure transient rate in accordance with LFT activity, observed in sequences in Mar. 2011, Oct. 2015, and April 2016. In the Oct. 2015 sequence, observed pressure transient in two boreholes indicates the slip propagates updip in the shallow subduction zone. In many sequences including this sequence, we ientify that the LFT swarm tends to migrate updip direction. The pressure transient in Apr. 2016 also followed this tendency, initiating from co-seismic compression by Apr. 1 earthquake occurred downdip side of the boreholes, followed by further compression due to the after slip, and slow release of the pressure suggesting SSE along with very active LFT and VLFE activities migrating offshore direction in the following two weeks period. The SSE seemed further activated by teleseismic events Kumamoto earthquake in Apr. 17.

Geodetic Observations Using GNSS, Tiltmeter, and DInSAR, at Tokachi-dake Volcano, Japan

NASA Astrophysics Data System (ADS)

Miyagi, Y.

2017-12-01

Tokachi-dake volcano is located in central Hokkaido, Japan. Middle sized eruptions occurred in 1926, 1962, and 1988-1989, and several small phreatic eruptions also occurred in the meanwhile. After the latest eruption in 1988-1989, many volcanic tremor and active seismicity were revealed. Active fumarolic activities from Taisho crater and 62-2 crater have been observed. In recent years, Tokachi-dake volcano has been observed by using several geodetic techniques, including DInSAR, GNSS, tiltmeter, and gravimeter, to detect regional and local signals associated with volcanic activities. Continuous GNSS stations in summit area operated by Geological Survey of Hokkaido and Hokkaido University [Okazaki et al., 2015] and DInSAR observations using ALOS-2 and TerraSAR-X data have revealed long-term small deformation after 2006 and transient large deformation in May, 2015. We found that these are quite local deformation, because regional GNSS and tiltmeter network did not detect any obvious signals in same period. The remarkable deformation detected by GNSS and DInSAR in the summit area between May and July, 2015, indicates that horizontal displacements are larger than vertical displacements, and westward displacement are much larger than eastward displacement. First, we try to model the deformation pattern using a simple spherical source model [Mogi, 1958] and a dike source model [Okada, 1985]. However, they cannot explain observed deformation because they do not take into consideration a topographic effect in the deformation area. Kawguchi & Miyagi [2016] tried to model the deformation using a boundary element method considering the topographic effect. Consequently, a deformation source which is vertically prolate spheroid beneath the summit shows a better fit between observed and simulated deformation. Annual campaign gravity observations have carried out by several Japanese university and institutes since 2010 [Takahashi et al., 2016]. These reveal that gravity value detected in summit area has decreased more than 0.15mgal up to 2017, which is larger than the gravity value expected from vertical displacements [Okazaki et al., 2017]. In this study, we introduce recent deformation observed by DInSAR, and try to understand the relationship between the deformation and gravity change.

The UNAVCO role in planning, building, and maintaining geodetic infrastructure across the Americas: update on PBO, COCONet, and TLALOCNet

NASA Astrophysics Data System (ADS)

Mattioli, G. S.; Braun, J. J.; Cabral, E.; Calais, E.; DeMets, C.; Feaux, K.; Mencin, D.; Miller, M. M.; Normandeau, J.; Serra, Y.; Wang, G.

2013-05-01

UNAVCO maintains the NSF-funded Plate Boundary Observatory (PBO), which is the geodetic facility of EarthScope. PBO is largest continuous GPS and borehole geophysical network in the Americas, with ~1130 cGPS sites, including several with multiple monuments, ~80 boreholes, with 75 tensor strainmeters, 79 short-period, 3-component seismometers, and pore pressure sensors at 23 sites. PBO also includes 26 tiltmeters deployed at several volcanoes. Surface meteorological sensors are collocated at 134 GPS sites. UNAVCO provides high-rate (1 Hz), low-latency (<1 s) GPS data streams (RT-GPS) from 348 stations in PBO and has delivered over 62 Tb of geodetic data since PBO's inception in 2004. COCONet is a multi-hazard GPS-Met observatory, which extends PBO infrastructure into the Caribbean basin. In 2010, UNAVCO in collaboration with UCAR, was funded by NSF to build and initially maintain a network of 50 new cGPS/Met sites and incorporate another 50 existing sites in the Caribbean region. The revised siting plan calls for 46 new, 21 refurbished, and 77 existing stations spanning 26 nations in the Caribbean. Data from COCONet sites flow into the UNAVCO archive and are processed by the PBO analysis centers. Three workshops have helped to foster a COCONet science community and provide important guidance to UNAVCO to assure success of this complex multi-national project. A new joint UNAVCO-Mexican multi-hazard GPS-Met observatory, called TLALOCNet, has been proposed based on the outcomes of a NSF-funded workshop held in Puerto Vallarta in 2010. The TLALOCNet plan calls for UNAVCO to install 9 new PBO-quality GPS-Met sites in Mexico and adjacent islands, upgrade 29 sites previously installed with NSF funding along the western subduction boundary, and coordinate with the Mexican National Meteorological Service to federate data from at least another 80 GPS-Met sites distributed across Mexico. All GPS-Met data from TLALOCNet will be freely available at the UNAVCO archive and Mexican mirror sites. The ultimate goal for these networks is to provide free, high-quality, low-latency data and data products for researchers, educators, students, and the private sector. Data from COCONet and TLALOCNet will be used by US and international scientists to study solid earth processes, for example plate kinematics and dynamic as well as plate boundary interactions and deformation, with an emphasis on the earthquake cycle. The networks also serve atmospheric science objectives by providing more precise estimates of tropospheric water vapor thus enabling better forecast of the dynamics of airborne moisture associated with the yearly Caribbean hurricane cycle.

76 FR 49676 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-11

... shoreline......... *26 City of Deltona. * National Geodetic Vertical Datum. + North American Vertical Datum... Boulevard. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground... feet +1000 upstream of Southeast 45th Street. * National Geodetic Vertical Datum. + North American...

The Dams and Monitoring Systems and Case Study: Ataturk and Karakaya Dams

NASA Astrophysics Data System (ADS)

Kalkan, Y.; Bilgi, S.; Gülnerman, A. G.

2017-12-01

Dams are among the most important engineering structures used for flood controls, agricultural purposes as well as drinking and hydroelectric power. Especially after the Second World War, developments on the construction technology, increase the construction of larger capacity dams. There are more than 150.000 dams in the world and almost 1000 dams in Turkey, according to international criteria. Although dams provide benefits to humans, they possess structural risks too. To determine the performance of dams on structural safety, assessing the spatial data is very important. These are movement, water pressure, seepage, reservoir and tail-water elevations, local seismic activities, total pressure, stress and strain, internal concrete temperature, ambient temperature and precipitation. These physical data are measured and monitored by the instruments and equipment. Dams and their surroundings have to be monitored by using essential methods at periodic time intervals in order to determine the possible changes that may occur over the time. Monitoring programs typically consist of; surveillance or visual observation. These programs on dams provide information for evaluating the dam's performance related to the design intent and expected changes that could affect the safety performance of the dam. Additionally, these programs are used for investigating and evaluating the abnormal or degrading performance where any remedial action is necessary. Geodetic and non-geodetic methods are used for monitoring. Monitoring the performance of the dams is critical for producing and maintaining the safe dams. This study provides some general information on dams and their different monitoring systems by taking into account two different dams and their structural specifications with the required information. The case study in this paper depends on a comparison of the monitoring surveys on Atatürk Dam and Karakaya Dam, which are constructed on Firat River with two different structural type in Turkey. In addition, brief information is given about these dams and the methods of geodetic and non-geodetic monitoring measurements applied by various disciplines. The last part of the study focuses on the inference of the geodetic monitoring methods, which depend on a seven years of geodetic monitoring.

Chasing a complete understanding of a rapid moving rock slide: the La Saxe landslide

NASA Astrophysics Data System (ADS)

Crosta, G. B.; Cancelli, P.; Tamburini, A.; Alberto, W.; Broccolato, M.; Castellanza, R.; Frattini, P.; Agliardi, F.; Rivolta, C.; Leva, D.

2012-04-01

Large deep seated slope deformations affect entire valley flanks and are characterized by slow to extremely slow present day displacement rates. Because of their extreme size, they are frequently characterized at their interior by secondary instabilities which can be classified as rockslides, that can originate large rock avalanches or can move at much faster rates with respect to the main mass. As a consequence local instabilities and reactivation of sectors of deep seated deformations should be carefully monitored and studied especially because they can affect strongly deformed and weakened rock masses. Because of these natural conditions and their preferential location in coincidence of slope steepening, these rockslides can undergo rapid evolution and activation putting the upmost urgency for monitoring, hazard and risk assessment. We present the case study of the La Saxe rockslide (Courmayeur, Aosta valley, Italy), located within a deep seated deformation affecting most of the 10 km long left hand flank of the Ferret valley (between 1340 m and 2300 m a.s.l.) and which underwent a major phase of acceleration in the last decade. The rockslide affects the extreme south western tip of the deep seated deformation at the outlet of Ferret valley, with an estimated volume of about 8 x 106 m3 of clay schists and thinly bedded black carbonates, intensely folded and faulted. An intense investigation activity has been performed in the last 2 years to reach a more complete understanding of the phenomenon. Boreholes have been drilled, logged, and instrumented to constrain the landslide volume, the rate of displacement at depth, and the water pressure. Displacement monitoring has been undertaken at successive steps by setting up sequentially: a distance measurement network (6 optical targets), a GPS network for periodic measurements (12 stations), a ground-based interferometer (GB-InSAR, LisaLab, by Ellegi, with 10 min acquisition intervals), a geodetic network based on a total station and 25 optical targets measured at 2 h intervals, a GPS network (7 stations) for quasi-real time measurements, four differential multiparametric borehole systems (DMS columns up to 100 m long). A geotechnical network has been also implemented including open pipe piezometers, borehole wire extensometers and inclinometric casings. This enormous monitoring effort is motivated by the extreme risk associated to this phenomenon, which is hanging over a famous touristic resort, a world famous cable way, the Mont Blanc highway, and in close proximity to the Mont Blanc tunnel. Rockslide characterization, failure surface definition, and groundwater flow investigations allowed for a series of slope stability analyses to be completed, together with modelling of the expected invasion area. Relationships with snowmelt have been ascertained and an early warning system based on real time measurements redundancy and all weather capabilities has been set up. LisaLab GB-InSAR equipment continuously provide spatially distributed displacement data which have been analysed to identify different failure scenarios and sensitivity of the landslide to triggering and controlling factors. Geodetic measurements are integrated with GB-InSAR data for verification and in depth 3D displacement reconstructions.

EarthScope's Plate Boundary Observatory in Alaska: Building on Existing Infrastructure to Provide a Platform for Integrated Research and Hazard-monitoring Efforts

NASA Astrophysics Data System (ADS)

Boyce, E. S.; Bierma, R. M.; Willoughby, H.; Feaux, K.; Mattioli, G. S.; Enders, M.; Busby, R. W.

2014-12-01

EarthScope's geodetic component in Alaska, the UNAVCO-operated Plate Boundary Observatory (PBO) network, includes 139 continuous GPS sites and 41 supporting telemetry relays. These are spread across a vast area, from northern AK to the Aleutians. Forty-five of these stations were installed or have been upgraded in cooperation with various partner agencies and currently provide data collection and transmission for more than one group. Leveraging existing infrastructure normally has multiple benefits, such as easier permitting requirements and costs savings through reduced overall construction and maintenance expenses. At some sites, PBO-AK power and communications systems have additional capacity beyond that which is needed for reliable acquisition of GPS data. Where permits allow, such stations could serve as platforms for additional instrumentation or real-time observing needs. With the expansion of the Transportable Array (TA) into Alaska, there is increased interest to leverage existing EarthScope resources for station co-location and telemetry integration. Because of the complexity and difficulty of long-term O&M at PBO sites, however, actual integration of GPS and seismic equipment must be considered on a case-by-case basis. UNAVCO currently operates two integrated GPS/seismic stations in collaboration with the Alaska Earthquake Center, and three with the Alaska Volcano Observatory. By the end of 2014, PBO and TA plan to install another four integrated and/or co-located geodetic and seismic systems. While three of these are designed around existing PBO stations, one will be a completely new TA installation, providing PBO with an opportunity to expand geodetic data collection in Alaska within the limited operations and maintenance phase of the project. We will present some of the design considerations, outcomes, and lessons learned from past and ongoing projects to integrate seismometers and other instrumentation at PBO-Alaska stations. Developing the PBO network as a platform for ongoing research and hazard monitoring equipment may also continue to serve the needs of the research community and the public beyond the sun-setting and completion of EarthScope science plan in 2018.

75 FR 43479 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-26

.... * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean... Evelyns Drive. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above.... * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean...

Fracture and slope stability monitoring at Puigcercós landslide (Catalonia, Spain)

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Vasquez, Sebastian; López, Robert; Guinau, Guinau; Calvet, Jaume; Vilaplana, Joan Manuel; Blanch, Xabier; Tapia, Mar; Roig, Pere; Suriñach, Emma

2017-04-01

The village of Puigcercós ( 50 inhabitants) is located in the region of Pallars Jussà (Lleida) in Catalonia, several km south of the town of Tremp. In 1881 the entire village had to be moved from its historical location on top of the hill to its current location. This was caused by a series of landslides caused by continuing rainfall. The most important landslide occurred on January 13th 1881, which displaced more than 5 million cubic meters of sediments and rocks and created an impressive rock scar of approximately 25 m height and 150 m width. The area where the sediments were accumulated is extensive, reaching 8 hectares. During the last years, our group has chosen the site of Puigcercós to conduct pilot studies of landslides and rockfalls using multidisciplinary approach, involving Terrestrial Laser Scanner, Total Station, DGPS, seismic monitoring and geophysical techniques. The geophysical surveys of the zone of the sediment accumulation, can help determine the internal structure of the displaced sediments. The work presented here mainly concerns the deformation monitoring at the site using geodetic techniques. In July 2015, a network of 11 new geodetic points has been established and measured with GPS. The location of these points was chosen with the purpose of answering two important questions in the studies of the stability and geomorphological activity of the Puigcercós landslide: 1) As a result of combined analysis of the tape-meter, total station and GPS measurements, we hope to obtain absolute values of deformation in the upper part of the escarpment, controlling the stability of the escarpment front and the associated fractures near the coronation. For this purpose, two geodetic control points have been established at the hilltop, some 5 meters away from the escarpment itself. 2) Determine the slope stability of the depositional area, where we established nine geodetic points. As of today, these points have been measured twice, in 2015 and 2016, during 24 hour long campaigns, overlapping a midnight. Thus, obtained GPS observations cover at least 8 hours for 2 consecutive days, ensuring the millimeter level accuracy after the post-processing using GAMIT/GLOBK software from MIT. After the realization of the third campaign in the spring of 2017, we hope to give more definitive answers to the questions raised above. This work is conducted within the framework of the project CHARMA (CGL2013-40828-R), financed by the Ministry of Economy, Industry and Competitiveness of Spain. We are thankful to the students who participated in the GPS campaigns: E. Bravo, M. Galindos, Ciscu Sánchez.

Development of a GNSS-Enhanced Tsunami Early Warning System

NASA Astrophysics Data System (ADS)

Bawden, G. W.; Melbourne, T. I.; Bock, Y.; Song, Y. T.; Komjathy, A.

2015-12-01

The past decade has witnessed a terrible loss of life and economic disruption caused by large earthquakes and resultant tsunamis impacting coastal communities and infrastructure across the Indo-Pacific region. NASA has funded the early development of a prototype real-time Global Navigation Satellite System (RT-GNSS) based rapid earthquake and tsunami early warning (GNSS-TEW) system that may be used to enhance seismic tsunami early warning systems for large earthquakes. This prototype GNSS-TEW system geodetically estimates fault parameters (earthquake magnitude, location, strike, dip, and slip magnitude/direction on a gridded fault plane both along strike and at depth) and tsunami source parameters (seafloor displacement, tsunami energy scale, and 3D tsunami initials) within minutes after the mainshock based on dynamic numerical inversions/regressions of the real-time measured displacements within a spatially distributed real-time GNSS network(s) spanning the epicentral region. It is also possible to measure fluctuations in the ionosphere's total electron content (TEC) in the RT-GNSS data caused by the pressure wave from the tsunami. This TEC approach can detect if a tsunami has been triggered by an earthquake, track its waves as they propagate through the oceanic basins, and provide upwards of 45 minutes early warning. These combined real-time geodetic approaches will very quickly address a number of important questions in the immediate minutes following a major earthquake: How big was the earthquake and what are its fault parameters? Could the earthquake have produced a tsunami and was a tsunami generated?

A technique for processing of planetary images with heterogeneous characteristics for estimating geodetic parameters of celestial bodies with the example of Ganymede

NASA Astrophysics Data System (ADS)

Zubarev, A. E.; Nadezhdina, I. E.; Brusnikin, E. S.; Karachevtseva, I. P.; Oberst, J.

2016-09-01

The new technique for generation of coordinate control point networks based on photogrammetric processing of heterogeneous planetary images (obtained at different time, scale, with different illumination or oblique view) is developed. The technique is verified with the example for processing the heterogeneous information obtained by remote sensing of Ganymede by the spacecraft Voyager-1, -2 and Galileo. Using this technique the first 3D control point network for Ganymede is formed: the error of the altitude coordinates obtained as a result of adjustment is less than 5 km. The new control point network makes it possible to obtain basic geodesic parameters of the body (axes size) and to estimate forced librations. On the basis of the control point network, digital terrain models (DTMs) with different resolutions are generated and used for mapping the surface of Ganymede with different levels of detail (Zubarev et al., 2015b).

EUPOS - Satellite multifunctional system of reference stations in Central and Eastern Europe

NASA Astrophysics Data System (ADS)

Sledzinski, J.

2003-04-01

The European project EUPOS (European Position Determination System) of establishment of a system of multifunctional satellite reference stations in Central and Eastern Europe is described in the paper. Fifteen countries intend to participate in the project: Bulgaria, Croatia, Czech Republic, Estonia, Germany, Hungary, Latvia, Lithuania, Macedonia, Poland, Romania, Russia, Serbia, Slovak Republic and Slovenia. One common project will be prepared for all countries, however it will include the existing or developed infrastructure in particular countries. The experiences of establishing and operating of the German network SAPOS as well as experiences gained by other countries will be used. The European network of stations will be compatible with the system SAPOS and future European system Galileo. The network of reference stations will provide signal for both positioning of the geodetic control points and for land, air and marine navigation. Several levels of positioning accuracy will be delivered.

GPS baseline configuration design based on robustness analysis

NASA Astrophysics Data System (ADS)

Yetkin, M.; Berber, M.

2012-11-01

The robustness analysis results obtained from a Global Positioning System (GPS) network are dramatically influenced by the configurationof the observed baselines. The selection of optimal GPS baselines may allow for a cost effective survey campaign and a sufficiently robustnetwork. Furthermore, using the approach described in this paper, the required number of sessions, the baselines to be observed, and thesignificance levels for statistical testing and robustness analysis can be determined even before the GPS campaign starts. In this study, wepropose a robustness criterion for the optimal design of geodetic networks, and present a very simple and efficient algorithm based on thiscriterion for the selection of optimal GPS baselines. We also show the relationship between the number of sessions and the non-centralityparameter. Finally, a numerical example is given to verify the efficacy of the proposed approach.

Seismicity Controlled by a Frictional Afterslip During a Small-Magnitude Seismic Sequence (ML < 5) on the Chihshang Fault, Taiwan

NASA Astrophysics Data System (ADS)

Canitano, Alexandre; Godano, Maxime; Hsu, Ya-Ju; Lee, Hsin-Ming; Linde, Alan T.; Sacks, Selwyn

2018-02-01

We report evidence for frictional afterslip at shallow depths (about 5 to 7 km) during a small-magnitude seismic sequence (with ML<5) along the Chihshang Fault, a main active structure of the Longitudinal Valley, in southeast Taiwan. The afterslip, which was recorded by a nearby borehole dilatometer, lasted about a month with a cumulative geodetic moment magnitude of 4.8 ± 0.2. The afterslip comprised two stages and controlled the aftershock sequence. The first postseismic stage, which followed a ML 4.6 earthquake, lasted about 6 h and mostly controlled the ruptures of neighboring asperities (e.g., multiplets) near the hypocenter. Then, a 4 week duration large afterslip event following a ML 4.9 earthquake controlled the rate of aftershocks during its first 2 days through brittle creep. The study presents a rare case of simultaneous seismological and geodetic observations for afterslip following earthquakes with magnitude lower than 5. Furthermore, the geodetic moment of the postseismic phase is at least equivalent to the coseismic moment of the sequence.

A catalog of coseismic uniform-slip models of geodetically unstudied earthquakes along the Sumatran plate boundary

NASA Astrophysics Data System (ADS)

Wong, N. Z.; Feng, L.; Hill, E.

2017-12-01

The Sumatran plate boundary has experienced five Mw > 8 great earthquakes, a handful of Mw 7-8 earthquakes and numerous small to moderate events since the 2004 Mw 9.2 Sumatra-Andaman earthquake. The geodetic studies of these moderate earthquakes have mostly been passed over in favour of larger events. We therefore in this study present a catalog of coseismic uniform-slip models of one Mw 7.2 earthquake and 17 Mw 5.9-6.9 events that have mostly gone geodetically unstudied. These events occurred close to various continuous stations within the Sumatran GPS Array (SuGAr), allowing the network to record their surface deformation. However, due to their relatively small magnitudes, most of these moderate earthquakes were recorded by only 1-4 GPS stations. With the limited observations per event, we first constrain most of the model parameters (e.g. location, slip, patch size, strike, dip, rake) using various external sources (e.g., the ANSS catalog, gCMT, Slab1.0, and empirical relationships). We then use grid-search forward models to explore a range of some of these parameters (geographic position for all events and additionally depth for some events). Our results indicate the gCMT centroid locations in the Sumatran subduction zone might be biased towards the west for smaller events, while ANSS epicentres might be biased towards the east. The more accurate locations of these events are potentially useful in understanding the nature of various structures along the megathrust, particularly the persistent rupture barriers.

Geodetic observations of ice flow velocities over the southern part of subglacial Lake Vostok, Antarctica, and their glaciological implications

NASA Astrophysics Data System (ADS)

Wendt, Jens; Dietrich, Reinhard; Fritsche, Mathias; Wendt, Anja; Yuskevich, Alexander; Kokhanov, Andrey; Senatorov, Anton; Lukin, Valery; Shibuya, Kazuo; Doi, Koichiro

2006-09-01

In the austral summer seasons 2001/02 and 2002/03, Global Positioning System (GPS) data were collected in the vicinity of Vostok Station to determine ice flow velocities over Lake Vostok. Ten GPS sites are located within a radius of 30km around Vostok Station on floating ice as well as on grounded ice to the east and to the west of the lake. Additionally, a local deformation network around the ice core drilling site 5G-1 was installed. The derived ice flow velocity for Vostok Station is 2.00ma-1 +/- 0.01ma-1. Along the flowline of Vostok Station an extension rate of about 10-5a-1 (equivalent to 1cm km-1 a-1) was determined. This significant velocity gradient results in a new estimate of 28700 years for the transit time of an ice particle along the Vostok flowline from the bedrock ridge in the southwest of the lake to the eastern shoreline. With these lower velocities compared to earlier studies and, hence, larger transit times the basal accretion rate is estimated to be 4mma-1 along a portion of the Vostok flowline. An assessment of the local accretion rate at Vostok Station using the observed geodetic quantities yields an accretion rate in the same order of magnitude. Furthermore, the comparison of our geodetic observations with results inferred from ice-penetrating radar data indicates that the ice flow may not have changed significantly for several thousand years.

A geodetic matched filter search for slow slip with application to the Mexico subduction zone

NASA Astrophysics Data System (ADS)

Rousset, B.; Campillo, M.; Lasserre, C.; Frank, W. B.; Cotte, N.; Walpersdorf, A.; Socquet, A.; Kostoglodov, V.

2017-12-01

Since the discovery of slow slip events, many methods have been successfully applied to model obvious transient events in geodetic time series, such as the widely used network strain filter. Independent seismological observations of tremors or low-frequency earthquakes and repeating earthquakes provide evidence of low-amplitude slow deformation but do not always coincide with clear occurrences of transient signals in geodetic time series. Here we aim to extract the signal corresponding to slow slips hidden in the noise of GPS time series, without using information from independent data sets. We first build a library of synthetic slow slip event templates by assembling a source function with Green's functions for a discretized fault. We then correlate the templates with postprocessed GPS time series. Once the events have been detected in time, we estimate their duration T and magnitude Mw by modeling a weighted stack of GPS time series. An analysis of synthetic time series shows that this method is able to resolve the correct timing, location, T, and Mw of events larger than Mw 6 in the context of the Mexico subduction zone. Applied on a real data set of 29 GPS time series in the Guerrero area from 2005 to 2014, this technique allows us to detect 28 transient events from Mw 6.3 to 7.2 with durations that range from 3 to 39 days. These events have a dominant recurrence time of 40 days and are mainly located at the downdip edges of the Mw>7.5 slow slip events.

A geodetic matched-filter search for slow slip with application to the Mexico subduction zone

NASA Astrophysics Data System (ADS)

Rousset, B.; Campillo, M.; Lasserre, C.; Frank, W.; Cotte, N.; Walpersdorf, A.; Socquet, A.; Kostoglodov, V.

2017-12-01

Since the discovery of slow slip events, many methods have been successfully applied to model obvious transient events in geodetic time series, such as the widely used network strain filter. Independent seismological observations of tremors or low frequency earthquakes and repeating earthquakes provide evidence of low amplitude slow deformation but do not always coincide with clear occurrences of transient signals in geodetic time series. Here, we aim to extract the signal corresponding to slow slips hidden in the noise of GPS time series, without using information from independent datasets. We first build a library of synthetic slow slip event templates by assembling a source function with Green's functions for a discretized fault. We then correlate the templates with post-processed GPS time series. Once the events have been detected in time, we estimate their duration T and magnitude Mw by modelling a weighted stack of GPS time series. An analysis of synthetic time series shows that this method is able to resolve the correct timing, location, T and Mw of events larger than Mw 6.0 in the context of the Mexico subduction zone. Applied on a real data set of 29 GPS time series in the Guerrero area from 2005 to 2014, this technique allows us to detect 28 transient events from Mw 6.3 to 7.2 with durations that range from 3 to 39 days. These events have a dominant recurrence time of 40 days and are mainly located at the down dip edges of the Mw > 7.5 SSEs.

Incorporating GPS geodetic data into the undergraduate classroom to improve data and information literacy

NASA Astrophysics Data System (ADS)

Jansma, P. E.; Mattioli, G. S.

2002-12-01

As part of an NSF-funded project, we are incorporating Global Positioning System (GPS) geodesy into the classroom to improve data and information literacy among undergraduate students. Our objectives are: to introduce statistical concepts essential for the interpretation of large datasets; to promote communication skills; to enhance critical thinking; and to build teamwork. GPS geodesy is ideal for illustrating data literacy concepts. Data precision and accuracy depend upon several factors, including type of equipment, environmental conditions, length of occupations, monument design, site location, configuration of the geodetic network, and processing strategies. All of these can be varied, allowing the students to learn the trade-offs among cost, time, and quality and to determine the most efficient methodology for specific problems. In addition, precision, accuracy, and errors govern the interpretations that can be made and the potential to distinguish among competing models. Our focus is a semester-long course that uses GPS geodesy in real-world applications and also requires integration of GPS data into oral presentations and written reports. Students work in teams on "cases" that pose hypotheses for testing. The cases are derived from our on-going research projects and take advantage of on-line continuous GPS (CGPS) data as well as our archived campaign data. The case studies are: 1) Microplate tectonics in the northeastern Caribbean; 2) Inflation/deflation cycles of the Soufriere Hills volcano, Montserrat; and 3) Contribution of monument instability to the overall error in geodetic data from the New Madrid Seismic Zone. All course materials will be on-line and available for the community.

Further characterization of the time transfer capabilities of precise point positioning (PPP): the Sliding Batch Procedure.

PubMed

Guyennon, Nicolas; Cerretto, Giancarlo; Tavella, Patrizia; Lahaye, François

2009-08-01

In recent years, many national timing laboratories have installed geodetic Global Positioning System receivers together with their traditional GPS/GLONASS Common View receivers and Two Way Satellite Time and Frequency Transfer equipment. Many of these geodetic receivers operate continuously within the International GNSS Service (IGS), and their data are regularly processed by IGS Analysis Centers. From its global network of over 350 stations and its Analysis Centers, the IGS generates precise combined GPS ephemeredes and station and satellite clock time series referred to the IGS Time Scale. A processing method called Precise Point Positioning (PPP) is in use in the geodetic community allowing precise recovery of GPS antenna position, clock phase, and atmospheric delays by taking advantage of these IGS precise products. Previous assessments, carried out at Istituto Nazionale di Ricerca Metrologica (INRiM; formerly IEN) with a PPP implementation developed at Natural Resources Canada (NRCan), showed PPP clock solutions have better stability over short/medium term than GPS CV and GPS P3 methods and significantly reduce the day-boundary discontinuities when used in multi-day continuous processing, allowing time-limited, campaign-style time-transfer experiments. This paper reports on follow-on work performed at INRiM and NRCan to further characterize and develop the PPP method for time transfer applications, using data from some of the National Metrology Institutes. We develop a processing procedure that takes advantage of the improved stability of the phase-connected multi-day PPP solutions while allowing the generation of continuous clock time series, more applicable to continuous operation/monitoring of timing equipment.

Applications of Differential Operators in Geodetic Coordinates

NASA Astrophysics Data System (ADS)

Hallam, K. A. T.; Oliveira, V. C., Jr.

2016-12-01

The definition of coordinate systems and frames is an essential step to even start a problem in physical geodesy and geophysics. The commonly used coordinate systems when dealing with problems on (or close to) the surface of the Earth are the geocentric Cartesian coordinates, geocentric spherical coordinates and geodetic coordinates. Transformations between Cartesian and spherical coordinates are widely known and used for several problems. More complex, but not less important, are the transformations between Cartesian and geodetic coordinates. Although most of them utilize an ellipsoidal frame in which the three coordinates are geodetic longitude (λ), geodetic latitude (φ) and the scale factor (u), the latter being a combination of X and Y, not the geometric height (h), the data sets measured on (or close to) the surface of the Earth are given in geodetic coordinates which are usually transformed into Cartesian or spherical coordinates for mathematical developments. It would be useful, however, to preclude coordinate transformations for the subsequent operations. Thus, we derived expressions for the gradient and Laplacian operators in geodetic coordinates in order to make further use on mathematical developments. Results obtained analitically and from numerical simulations validate our expressions. We applied our operators to derive the gravitational field produced by a point mass and used it for representing the regional gravity field in geodetic coordinates. The results obtained with the numerical simulations show that our approach is potentially useful in solving a wide range of problems in physical geodesy and geophysics.

Surface and Subsurface Geodesy Combined with Active Borehole Experimentation for the Advanced Characterization of EGS Reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elsworth, Derek; Im, Kyungjae; Guglielmi, Yves

2016-11-14

We explore the utility of combining active downhole experimentation with borehole and surface geodesy to determine both the characteristics and evolving state of EGS reservoirs during stimulation through production. The study is divided into two parts. We demonstrate the feasibility of determining in situ reservoir characteristics of reservoir size, strain and fracture permeability and their dependence on feedbacks of stress and temperature using surface and borehole geodetic measurements (Part I). We then define the opportunity to apply the unique hydraulic pulse protocol (HPP) borehole tool to evaluate reservoir state. This can be accomplished by monitoring and co-inverting measured reservoir characteristicsmore » (from the HPP tool) with surface geodetic measurements of deformation, tilt and strain with continuous measurements of borehole-wall strain (via optical fiber and fiber Bragg gratings) and measured flow rates (Part II).« less

GPS Imaging of Time-Variable Earthquake Hazard: The Hilton Creek Fault, Long Valley California

NASA Astrophysics Data System (ADS)

Hammond, W. C.; Blewitt, G.

2016-12-01

The Hilton Creek Fault, in Long Valley, California is a down-to-the-east normal fault that bounds the eastern edge of the Sierra Nevada/Great Valley microplate, and lies half inside and half outside the magmatically active caldera. Despite the dense coverage with GPS networks, the rapid and time-variable surface deformation attributable to sporadic magmatic inflation beneath the resurgent dome makes it difficult to use traditional geodetic methods to estimate the slip rate of the fault. While geologic studies identify cumulative offset, constrain timing of past earthquakes, and constrain a Quaternary slip rate to within 1-5 mm/yr, it is not currently possible to use geologic data to evaluate how the potential for slip correlates with transient caldera inflation. To estimate time-variable seismic hazard of the fault we estimate its instantaneous slip rate from GPS data using a new set of algorithms for robust estimation of velocity and strain rate fields and fault slip rates. From the GPS time series, we use the robust MIDAS algorithm to obtain time series of velocity that are highly insensitive to the effects of seasonality, outliers and steps in the data. We then use robust imaging of the velocity field to estimate a gridded time variable velocity field. Then we estimate fault slip rate at each time using a new technique that forms ad-hoc block representations that honor fault geometries, network complexity, connectivity, but does not require labor-intensive drawing of block boundaries. The results are compared to other slip rate estimates that have implications for hazard over different time scales. Time invariant long term seismic hazard is proportional to the long term slip rate accessible from geologic data. Contemporary time-invariant hazard, however, may differ from the long term rate, and is estimated from the geodetic velocity field that has been corrected for the effects of magmatic inflation in the caldera using a published model of a dipping ellipsoidal magma chamber. Contemporary time-variable hazard can be estimated from the time variable slip rate estimated from the evolving GPS velocity field.

Methodological and experimental study of the relationship between displacement rate of landslide and GNSS strategy for deformation monitoring

NASA Astrophysics Data System (ADS)

Giordan, Daniele; Piras, Marco; Allasia, Paolo; Dabove, Paolo

2016-04-01

The use of GNSS for landslide monitoring is not a novelty. In the field of large slope instabilities, where the phenomena are usually wide and the use of complex monitoring networks is needed, often a continuous monitoring is required. In this case, the installed GNSS solution is composed by a dual frequency receiver, with a solar power and with a radio connection to a ground station, where the measurement sessions of the rovers are collected and processed. The management of the collected data is the most critical aspect because the approach, which is commonly used, assumes a fixed position of the GNSS antenna during the acquisition time window. When the landslide is active, the position shift of the point can be considered insignificant for the low displacement rate, but together with the increase of the velocity, the GNSS time series processing becomes a crucial aspect to obtain reliable and enough accurate measurements. Starting from real case studies as the Italian large slope instabilities of Montaguto (Avellino, Italy) and Mont de La Saxe (Courmayeur, Italy), we focused on the presence of different kinematic domains with dissimilar displacement behaviors and velocities. In particular, the range of velocities registered during the main active periods ranges from several millimeters/day up to several meters/day, so the strategy for the GNSS processing data must be very different. Methodology for data acquisition (continuous or windowed) and its duration, type of receivers and antenna used (single or dual frequency, GPS or GNSS, mass market or geodetic), data processing strategies (i.e. single epoch, kinematic), and eventually GNSS network services are fundamental factors, which may favor one or another solution, according to time, economy and infrastructure readiness in the field. In the greater part of these studies, the choices were made based on the experience of responsible in the similar conditions. Starting from the behavior of real cases previously cited, this work investigates a relationship between methodology and capability for displacement detection. Using a dedicated slide which allows to define a micrometric displacement, several tests have been carried out at Politecnico of Torino, where different receivers-antenna combinations (from geodetic to mass market) and displacement strategies have been considered. Furthermore, data processing has been realized by means of different software (commercial and FOS) and different kinds of solution. The results of this experimental activity evidenced that it is possible to define a correlation between the GNSS acquisition strategy and the velocity range of the monitored landslide, which could be now coupled with the landslide velocity scale proposed by Cruden & Varnes. In this way, it is possible to optimize costs for monitoring activities and to allow a "smart" use of GNSS technologies for monitoring.

23 CFR 630.402 - Policy.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Policy. 630.402 Section 630.402 Highways FEDERAL HIGHWAY... Geodetic Markers § 630.402 Policy. (a) Geodetic surveys along Federal-aid highway routes may be programmed as Federal-aid highway projects. (b) All geodetic survey work performed as a Federal-aid highway...

Fallon, Nevada FORGE Geodetic Data

DOE Data Explorer

Blankenship, Doug; Eneva, Mariana; Hammond, William

2018-02-01

Fallon FORGE InSAR and geodetic GPS deformation data. InSAR shapefiles are packaged together as .MPK (ArcMap map package, compatible with other GIS platforms), and as .CSV comma-delimited plaintext. GPS data and additional metadata are linked to the Nevada Geodetic Laboratory database at the Univ. of Nevada, Reno (UNR).

A Comparison of Moment Rates for the Eastern Mediterranean Region from Competitive Kinematic Models

NASA Astrophysics Data System (ADS)

Klein, E. C.; Ozeren, M. S.; Shen-Tu, B.; Galgana, G. A.

2017-12-01

Relatively continuous, complex, and long-lived episodes of tectonic deformation gradually shaped the lithosphere of the eastern Mediterranean region into its present state. This large geodynamically interconnected and seismically active region absorbs, accumulates and transmits strains arising from stresses associated with: (1) steady northward convergence of the Arabian and African plates; (2) differences in lithospheric gravitational potential energy; and (3) basal tractions exerted by subduction along the Hellenic and Cyprus Arcs. Over the last twenty years, numerous kinematic models have been built using a variety of assumptions to take advantage of the extensive and dense GPS observations made across the entire region resulting in a far better characterization of the neotectonic deformation field than ever previously achieved. In this study, three separate horizontal strain rate field solutions obtained from three, region-wide, GPS only based kinematic models (i.e., a regional block model, a regional continuum model, and global continuum model) are utilized to estimate the distribution and uncertainty of geodetic moment rates within the eastern Mediterranean region. The geodetic moment rates from each model are also compared with seismic moment release rates gleaned from historic earthquake data. Moreover, kinematic styles of deformation derived from each of the modeled horizontal strain rate fields are examined for their degree of correlation with earthquake rupture styles defined by proximal centroid moment tensor solutions. This study suggests that significant differences in geodetically obtained moment rates from competitive kinematic models may introduce unforeseen bias into regularly updated, geodetically constrained, regional seismic hazard assessments.

Recent geophysical investigation at Somma-Vesuvio volcanic complex

NASA Astrophysics Data System (ADS)

Berrino, Giovanna; Coppa, Ugo; De Natale, Giuseppe; Pingue, Folco

1993-11-01

Activity at Somma-Vesuvio volcanic area in southern Italy is monitored by seismic stations and periodic geodetic and gravity surveys. The seismic network, which consists at present of four vertical stations and one three-component station, recorded an increase in earthquake activity in 1978 and between November 1988 and March 1989. During the later activity, earthquakes were located in a cluster about 3 km beneath the summit of the volcano. Two tide gauges, two tiltmeters and a recording gravimeter are also operating at Somma-Vesuvio. Yearly levelling surveys are conducted along several closed routes that extend from as much as 6 km from the base of the volcano to the summit area. Survey results reveal no significant ground movement since 1959, except for a slight subsidence around the rim of the summit crater. Gravity changes have been larger than the expected 10 μGal uncertainty of the measurements. The lack of contemporary elevation changes implies that the observed gravity changes are the result of a slight change in density structure. The cone of Somma-Vesuvio has been very stable for the last few decades, showing no indications of a buildup to activity. The lack of surface movement should rule out a magma-supply rate to this volcano at the historic eruptive rate of 0.002 km 3/yr.

Transformation pipelines for PROJ.4

NASA Astrophysics Data System (ADS)

Knudsen, Thomas; Evers, Kristian

2017-04-01

For more than 2 decades, PROJ.4 has been the globally leading map projection library for open source (and probably also closed source) geospatial software. While focusing on mathematically well defined 2D projections from geographical to planar coordinates, PROJ.4 has nevertheless, since its introduction in the 1980s, provided limited support for more general geodetic datum transformations, and has gradually introduced a higher degree of support for 3D coordinate data and reference systems. The support has, however, been implemented over a long period of time, as need became evident and opportunity was found, by a number of different people, with different needs and at different times. Hence, the PROJ.4 3D support has not been the result of neither deep geodetic, nor careful code architectural considerations. This has resulted in a library that supports only a subset of commonly occurring geodetic transformations. To be more specific: It supports any datum shift that can be completed by a combination of two Helmert shifts (to and from a pivot datum) and, potentially, also a non-linear planar correction derived from interpolation in a correction grid. While this is sufficient for most small scale mapping activities, it is not at all sufficient for operational geodetic use, nor for many of the rapidly emerging high accuracy geospatial applications in agriculture, construction, transportation and utilities. To improve this situation, we have introduced a new framework for implementation of geodetic transformations, which will appear in the next release of the PROJ.4 library. Before describing the details, let us first remark that most cases of geodetic transformations can be expressed as a series of elementary operations, the output of one operation being the input of the next. E.g. when going from UTM zone 32, datum ED50, to UTM zone 32, datum ETRS89, one must, in the simplest case, go through 5 steps: Back-project the UTM coordinates to geographic coordinates Convert the geographic coordinates to 3D cartesian geocentric coordinates Apply a Helmert transformation from ED50 to ETRS89 Convert back from cartesian to geographic coordinates Finally project the geographic coordinates to UTM zone 32 planar coordinates. The homology between these steps and a Unix shell style pipeline is evident. With this as its main architectural inspiration, the primary feature of our implementation is a pipeline driver, that takes as its user supplied arguments, a series of elementary operations, which it strings together in order to implement the full transformation needed. Also, we have added a number of elementary geodetic operations, including Helmert transformations, general high order polynomial shifts (2D Horner's scheme) and the abridged Molodensky transformation. In anticipation of upcoming support for full time-varying transformations, we also introduce a 4D spatiotemporal data type, and a programming interface (API) for handling this. With these improvements in place, we assert that PROJ.4 is now well on its way from being a mostly-map-projection library, to becoming an almost-generic-geodetic-transformation library.

Joint Seismic-Geodetic Algorithm for Finite-Fault Detection and Slip Inversion in the West Coast ShakeAlert System

NASA Astrophysics Data System (ADS)

Smith, D. E.; Felizardo, C.; Minson, S. E.; Boese, M.; Langbein, J. O.; Murray, J. R.

2016-12-01

Finite-fault source algorithms can greatly benefit earthquake early warning (EEW) systems. Estimates of finite-fault parameters provide spatial information, which can significantly improve real-time shaking calculations and help with disaster response. In this project, we have focused on integrating a finite-fault seismic-geodetic algorithm into the West Coast ShakeAlert framework. The seismic part is FinDer 2, a C++ version of the algorithm developed by Böse et al. (2012). It interpolates peak ground accelerations and calculates the best fault length and strike from template matching. The geodetic part is a C++ version of BEFORES, the algorithm developed by Minson et al. (2014) that uses a Bayesian methodology to search for the most probable slip distribution on a fault of unknown orientation. Ultimately, these two will be used together where FinDer generates a Bayesian prior for BEFORES via the methodology of Minson et al. (2015), and the joint solution will generate estimates of finite-fault extent, strike, dip, best slip distribution, and magnitude. We have created C++ versions of both FinDer and BEFORES using open source libraries and have developed a C++ Application Protocol Interface (API) for them both. Their APIs allow FinDer and BEFORES to contribute to the ShakeAlert system via an open source messaging system, ActiveMQ. FinDer has been receiving real-time data, detecting earthquakes, and reporting messages on the development system for several months. We are also testing FinDer extensively with Earthworm tankplayer files. BEFORES has been tested with ActiveMQ messaging in the ShakeAlert framework, and works off a FinDer trigger. We are finishing the FinDer-BEFORES connections in this framework, and testing this system via seismic-geodetic tankplayer files. This will include actual and simulated data.

Evaluating Commercial and Private Cloud Services for Facility-Scale Geodetic Data Access, Analysis, and Services

NASA Astrophysics Data System (ADS)

Meertens, C. M.; Boler, F. M.; Ertz, D. J.; Mencin, D.; Phillips, D.; Baker, S.

2017-12-01

UNAVCO, in its role as a NSF facility for geodetic infrastructure and data, has succeeded for over two decades using on-premises infrastructure, and while the promise of cloud-based infrastructure is well-established, significant questions about suitability of such infrastructure for facility-scale services remain. Primarily through the GeoSciCloud award from NSF EarthCube, UNAVCO is investigating the costs, advantages, and disadvantages of providing its geodetic data and services in the cloud versus using UNAVCO's on-premises infrastructure. (IRIS is a collaborator on the project and is performing its own suite of investigations). In contrast to the 2-3 year time scale for the research cycle, the time scale of operation and planning for NSF facilities is for a minimum of five years and for some services extends to a decade or more. Planning for on-premises infrastructure is deliberate, and migrations typically take months to years to fully implement. Migrations to a cloud environment can only go forward with similar deliberate planning and understanding of all costs and benefits. The EarthCube GeoSciCloud project is intended to address the uncertainties of facility-level operations in the cloud. Investigations are being performed in a commercial cloud environment (Amazon AWS) during the first year of the project and in a private cloud environment (NSF XSEDE resource at the Texas Advanced Computing Center) during the second year. These investigations are expected to illuminate the potential as well as the limitations of running facility scale production services in the cloud. The work includes running parallel equivalent cloud-based services to on premises services and includes: data serving via ftp from a large data store, operation of a metadata database, production scale processing of multiple months of geodetic data, web services delivery of quality checked data and products, large-scale compute services for event post-processing, and serving real time data from a network of 700-plus GPS stations. The evaluation is based on a suite of metrics that we have developed to elucidate the effectiveness of cloud-based services in price, performance, and management. Services are currently running in AWS and evaluation is underway.

Discoveries and Controversies in Geodetic Imaging of Deformation Before and After the M=9 Tohoku-oki Earthquake

NASA Astrophysics Data System (ADS)

Wang, K.; Sun, T.; Hino, R.; Iinuma, T.; Tomita, F.; Kido, M.

2017-12-01

Numerous observations pertaining to the M=9.0 2011 Tohoku-oki earthquake have led to new understanding of subduction zone earthquakes. By synthesizing published research results and our own findings, we explore what has been learned about fault behavior and Earth rheology from geodetic imaging of crustal deformation before and after the earthquake. Before the earthquake, megathrust locking models based on land-based geodetic observations correctly outlined the along-strike location of the future rupture zone, showing that land-based observations are capable of resolving along-strike variations in locking and creep at wavelengths comparable to distances from the network. But they predicted a locked zone that was much deeper than the actual rupture in 2011. The incorrect definition of the locking pattern in the dip direction demonstrates not only the need for seafloor geodesy but also the importance of modeling interseismic viscoelastic stress relaxation and stress shadowing. The discovery of decade-long accelerated slip downdip of the future rupture zone raises new questions on fault mechanics. After the earthquake, seafloor geodetic discovery of opposing motion offshore provided unambiguous evidence for the dominance of viscoelastic relaxation in short-term postseismic deformation. There is little deep afterslip in the fault area where the decade-long pre-earthquake slip acceleration is observed. The complementary spatial distribution of pre-slip and afterslip calls for new scientific research. However, the near absence of deep afterslip directly downdip of the main rupture is perceived to be controversial because some viscoelastic models do predict large afterslip here, although less than predicted by purely elastic models. We show that the large afterslip in these models is largely an artefact due to the use of a layered Earth model without a subducting slab. The slab acts as an "anchor" in the mantle and retards landward motion following a subduction earthquake. Neglecting the slab causes fast landward motion of the trench area that has to be prevented by using a high value of mantle viscosity. The incorrect high viscosity, however, slows down the seaward motion of the coastal area, which has to be compensated by introducing deep afterslip.

Preliminary Obtained Data from Borehole Geodetic Measurements in Marmara Region, Turkey

NASA Astrophysics Data System (ADS)

Ozener, H.; Aktug, B.; Karabulut, H.; Ergintav, S.; Dogru, A.; Yilmaz, O.; Turgut, B.; Ahiska, B.; Mencin, D.; Mattioli, G. S.

2014-12-01

Dense continuous GPS networks quantify the time-dependent deformation field of the earthquake cycle. However the strainmeters can capture signals with superior precision at local spatial scales, in particular in the short-period, from minutes to a month. Many relatively small-scale events (e.i. SSEs, creeps) have been successfully determined on the subduction zones. Istanbul located near the most active parts of the North Anatolian Fault (NAF) has been monitored by different observing techniques such as seismic networks and continuous/survey-mode GPS networks for decades. However, it is still essential to observe deformation in a broad range of temporal and spatial scales (from seismology to geodesy and to geology). Borehole strainmeters are very sensitive to deformation in the range of less than a month. In this study, we present a new project, financially and technically supported by Istanbul Development Agency (ISTKA) and UNAVCO, respectively, which includes the installation of two borehole strainmeters are being deployed in European side of Istanbul in Marmara Region. Since these instruments can also respond to non-tectonic processes, it is necessary to have more instruments to increase spatial coherence and to have additional sensors to detect and model noise (such as barometric pressure, tides, or precipitation). The introduced monitoring system will provide significant insight about the creeping phenomenon and the possible SSE to our understanding of seismic hazards in active zones and possible precursors. Our long term objective is to build a borehole monitoring system in the region. By integrating various data obtained from borehole observations, we expect to get a better understanding of dynamics in the western NAF. In this presentation, we introduce data and ongoing analysis obtained with strainmeters.

Satellite-Based Investigations of the Transition from an Oceanic to Continental Transform Margin

NASA Technical Reports Server (NTRS)

Miller, M. Meghan

1998-01-01

Detailed characterization of neotectonics evolution of the Valle de San Felipe and Arroyo Grande regions in northern Baja California. Reoccupied GEOMEX GPS sites, and occupied a regional GPS (Global Positioning System) network. The Baja California peninsula in Mexico offers a unique setting for studying the kinematic evolution of a complex, active strike-slip/rift plate boundary. We are currently conducting remote sensing, geologic, and geodetic studies of this boundary. The combined data sets will yield instantaneous and time integrated views of its evolution. This proposal solicits renewed funding from NASA to support remote sensing and geologic studies. During the late Cenozoic, Baja California has been the locus of changing fault geometry that has accommodated components of the relative motion between the North America and Pacific plates. Contemporary slip between the two plates occurs in a broad zone that encompasses much of southern California and the Baja California Peninsula. The transfer of slip across this zone in southern California is relatively well understood. South of the border, the geometry and role of specific faults and structural provinces in transferring plate margin deformation across the peninsula is enigmatic. Results We use Landsat Thematic Mapper imagery of the Baja California Peninsula to identify recent and active faults, and then conduct field studies that characterize the temporal and spatial structural evolution of the plate margin. These data address questions concerning the neotectonic development of the Gulf of California, the Baja California Peninsula, and their role in evolution of the post-Miocene Pacific - North American plate boundary. Moreover, these studies provide constraints on the geometry of active faults, allowing more exact understanding of the results of ongoing NASA-supported geodetic experiments. In addition, anticipated publication of the TM scenes will provide a widely available geological data base for relatively little-known peninsula California. Achievements include development of an ArcInfo data base of Landsat and SPOT imagery, detailed field studies of Neogene structures in northeastern Baja California, and new constraint on Pacific - North America plate motion at Baja California latitudes. These results are reported in maps, manuscripts and data products which are published or near completion.

Preliminary results on the current tectonic setting of South Georgia Island from GPS geodetic data.

NASA Astrophysics Data System (ADS)

Matheny, P.; Smalley, R., Jr.; Dalziel, I. W. D.; Lawver, L. A.; Gomez, D.; Teferle, F. N.; Hunegnaw, A.; Abraha, K. E.

2017-12-01

The South Georgia microcontinent is an allochthonous block from the south eastern part of Tierra del Fuego of South America that has been transported over the past 80-100 My as part of the development of the Scotia Plate. While the trajectory to its current position is poorly constrained, the microcontinent is now part of the eastern end of the North Scotia Ridge between the South America and the Scotia Plates almost 1600 km east of its original position. Based on bathymetric morphology and geological history of the Scotia Arc the microcontinent has been considered to be part of the Scotia Plate, with the plate boundary continuing along the North Scotia Ridge on the north side of the microcontinent, to the east where it transitions into the South Sandwich subduction boundary. Seismic activity in the region, while very low, is concentrated along the southern border of the microcontinent. This seismicity has been interpreted, based on a few small events with thrust mechanisms, to represent underthrusting and uplift of the island on a restraining bend in the North Scotia Ridge geometry to the north-east of the microcontinent. More recently, based on the seismicity distribution, the plate boundary has been placed along the south side of the microcontinent, suggesting that it has, or is being, transferred to the South America plate. In order to address the current tectonic affinity of South Georgia a four station continuous GPS network was installed on South Georgia Island to determine the block's relative motion with respect to the South America and Scotia Plates. The question is whether it is now attached to either plate or is an independent platelet, and whether it is suffering internal deformation. We will present the preliminary geodetic results based on 3 years of continuous GPS data.

Miocene−Pleistocene deformation of the Saddle Mountains: Implications for seismic hazard in central Washington, USA

USGS Publications Warehouse

Staisch, Lydia; Kelsey, Harvey; Sherrod, Brian; Möller, Andreas; Paces, James B.; Blakely, Richard J.; Styron, Richard

2017-01-01

The Yakima fold province, located in the backarc of the Cascadia subduction zone, is a region of active strain accumulation and deformation distributed across a series of fault-cored folds. The geodetic network in central Washington has been used to interpret large-scale N-S shortening and westward-increasing strain; however, geodetic data are unable to resolve shortening rates across individual structures in this low-strain-rate environment. Resolving fault geometries, slip rates, and timing of faulting in the Yakima fold province is critically important to seismic hazard assessment for nearby infrastructure and population centers.The Saddle Mountains anticline is one of the most prominent Yakima folds. It is unique within the Yakima fold province in that the syntectonic strata of the Ringold Formation are preserved and provide a record of deformation and drainage reorganization. Here, we present new stratigraphic columns, U-Pb zircon tephra ages, U-series caliche ages, and geophysical modeling that constrain two line-balanced and retrodeformed cross sections. These new constraints indicate that the Saddle Mountains anticline has accommodated 1.0−1.3 km of N-S shortening since 10 Ma, that shortening increases westward along the anticline, and that the average slip rate has increased 6-fold since 6.8 Ma. Provenance analysis suggests that the source terrane for the Ringold Formation was similar to that of the modern Snake River Plain. Using new slip rates and structural constraints, we calculate the strain accumulation time, interpretable as a recurrence interval, for earthquakes on the Saddle Mountains fault and find that large-magnitude earthquakes could rupture along the Saddle Mountains fault every 2−11 k.y.

Modelling energy production by small hydro power plants in collective irrigation networks of Calabria (Southern Italy)

NASA Astrophysics Data System (ADS)

Zema, Demetrio Antonio; Nicotra, Angelo; Tamburino, Vincenzo; Marcello Zimbone, Santo

2017-04-01

The availability of geodetic heads and considerable water flows in collective irrigation networks suggests the possibility of recovery potential energy using small hydro power plants (SHPP) at sustainable costs. This is the case of many Water Users Associations (WUA) in Calabria (Southern Italy), where it could theoretically be possible to recovery electrical energy out of the irrigation season. However, very few Calabrian WUAs have currently built SHPP in their irrigation networks and thus in this region the potential energy is practically fully lost. A previous study (Zema et al., 2016) proposed an original and simple model to site turbines and size their power output as well as to evaluate profits of SHPP in collective irrigation networks. Applying this model at regional scale, this paper estimates the theoretical energy production and the economic performances of SHPP installed in collective irrigation networks of Calabrian WUAs. In more detail, based on digital terrain models processed by GIS and few parameters of the water networks, for each SHPP the model provides: (i) the electrical power output; (iii) the optimal water discharge; (ii) costs, revenues and profits. Moreover, the map of the theoretical energy production by SHPP in collective irrigation networks of Calabria was drawn. The total network length of the 103 water networks surveyed is equal to 414 km and the total geodetic head is 3157 m, of which 63% is lost due to hydraulic losses. Thus, a total power output of 19.4 MW could theoretically be installed. This would provide an annual energy production of 103 GWh, considering SHPPs in operation only out of the irrigation season. The single irrigation networks have a power output in the range 0.7 kW - 6.4 MW. However, the lowest SHPPs (that is, turbines with power output under 5 kW) have been neglected, because the annual profit is very low (on average less than 6%, Zema et al., 2016). On average each irrigation network provides an annual revenue from electrical energy sale of about 103000 €. Even though this revenue may appear quite low, it represents an important share of the annual WUA income. For the entire region, the total revenues from recovery energy in collective irrigation networks through SHPPs have been estimated in about 12 million Euros; investment and operating costs have been evaluated by parametric equations and the total profit theoretically available for each WUA has been quantified. This study has shown the economic opportunity of integrating SHPP in existing collecting irrigation networks of WUAs, in view of providing additional economic resources for users and enhancing the exploitation of a renewable energy source. REFERENCE Zema D.A., Nicotra A., Tamburino V., Zimbone S.M. 2016. A simple method to evaluate the technical and economic feasibility of micro hydro power plants in existing irrigation systems. Renewable Energy 85, 498-506. DOI: 10.1016/j.renene.2015.06.066.

Development of a composite geodetic structure for space construction, phase 2

NASA Technical Reports Server (NTRS)

1981-01-01

Primary physical and mechanical properties were defined for pultruded hybrid HMS/E-glass P1700 rod material used for the fabrication of geodetic beams. Key properties established were used in the analysis, design, fabrication, instrumentation, and testing of a geodetic parameter cylinder and a lattice cone closeout joined to a short cylindrical geodetic beam segment. Requirements of structural techniques were accomplished. Analytical procedures were refined and extended to include the effect of rod dimensions for the helical and longitudinal members on local buckling, and the effect of different flexural and extensional moduli on general instability buckling.

GEODYN system description, volume 1. [computer program for estimation of orbit and geodetic parameters

NASA Technical Reports Server (NTRS)

Chin, M. M.; Goad, C. C.; Martin, T. V.

1972-01-01

A computer program for the estimation of orbit and geodetic parameters is presented. The areas in which the program is operational are defined. The specific uses of the program are given as: (1) determination of definitive orbits, (2) tracking instrument calibration, (3) satellite operational predictions, and (4) geodetic parameter estimation. The relationship between the various elements in the solution of the orbit and geodetic parameter estimation problem is analyzed. The solution of the problems corresponds to the orbit generation mode in the first case and to the data reduction mode in the second case.

Soft computing methods for geoidal height transformation

NASA Astrophysics Data System (ADS)

Akyilmaz, O.; Özlüdemir, M. T.; Ayan, T.; Çelik, R. N.

2009-07-01

Soft computing techniques, such as fuzzy logic and artificial neural network (ANN) approaches, have enabled researchers to create precise models for use in many scientific and engineering applications. Applications that can be employed in geodetic studies include the estimation of earth rotation parameters and the determination of mean sea level changes. Another important field of geodesy in which these computing techniques can be applied is geoidal height transformation. We report here our use of a conventional polynomial model, the Adaptive Network-based Fuzzy (or in some publications, Adaptive Neuro-Fuzzy) Inference System (ANFIS), an ANN and a modified ANN approach to approximate geoid heights. These approximation models have been tested on a number of test points. The results obtained through the transformation processes from ellipsoidal heights into local levelling heights have also been compared.

Strong S-wave attenuation and actively degassing magma beneath Taal volcano, Philippines, inferred from source location analysis using high-frequency seismic amplitudes

NASA Astrophysics Data System (ADS)

Kumagai, H.; Lacson, R. _Jr., Jr.; Maeda, Y.; Figueroa, M. S., II; Yamashina, T.

2014-12-01

Taal volcano, Philippines, is one of the world's most dangerous volcanoes given its history of explosive eruptions and its close proximity to populated areas. A key feature of these eruptions is that the eruption vents were not limited to Main Crater but occurred on the flanks of Volcano Island. This complex eruption history and the fact that thousands of people inhabit the island, which has been declared a permanent danger zone, together imply an enormous potential for disasters. The Philippine Institute of Volcanology and Seismology (PHIVOLCS) constantly monitors Taal, and international collaborations have conducted seismic, geodetic, electromagnetic, and geochemical studies to investigate the volcano's magma system. Realtime broadband seismic, GPS, and magnetic networks were deployed in 2010 to improve monitoring capabilities and to better understand the volcano. The seismic network has recorded volcano-tectonic (VT) events beneath Volcano Island. We located these VT events based on high-frequency seismic amplitudes, and found that some events showed considerable discrepancies between the amplitude source locations and hypocenters determined by using onset arrival times. Our analysis of the source location discrepancies points to the existence of a region of strong S-wave attenuation near the ground surface beneath the east flank of Volcano Island. This region is beneath the active fumarolic area and above sources of pressure contributing inflation and deflation, and it coincides with a region of high electrical conductivity. The high-attenuation region matches that inferred from an active-seismic survey conducted at Taal in 1993. Our results, synthesized with previous results, suggest that this region represents actively degassing magma near the surface, and imply a high risk of future eruptions on the east flank of Volcano Island.

Shallow very-low-frequency earthquakes accompany slow slip events in the Nankai subduction zone.

PubMed

Nakano, Masaru; Hori, Takane; Araki, Eiichiro; Kodaira, Shuichi; Ide, Satoshi

2018-03-14

Recent studies of slow earthquakes along plate boundaries have shown that tectonic tremor, low-frequency earthquakes, very-low-frequency events (VLFEs), and slow-slip events (SSEs) often accompany each other and appear to share common source faults. However, the source processes of slow events occurring in the shallow part of plate boundaries are not well known because seismic observations have been limited to land-based stations, which offer poor resolution beneath offshore plate boundaries. Here we use data obtained from seafloor observation networks in the Nankai trough, southwest of Japan, to investigate shallow VLFEs in detail. Coincident with the VLFE activity, signals indicative of shallow SSEs were detected by geodetic observations at seafloor borehole observatories in the same region. We find that the shallow VLFEs and SSEs share common source regions and almost identical time histories of moment release. We conclude that these slow events arise from the same fault slip and that VLFEs represent relatively high-frequency fluctuations of slip during SSEs.

Highlights and Opportunities from Continuous Access to Gas Hydrates Sites at Ocean Networks Canada's NEPTUNE Observatory

NASA Astrophysics Data System (ADS)

Scherwath, M.; Heesemann, M.; Riedel, M.; Thomsen, L.; Roemer, M.; Chatzievangelou, D.; Purser, A.

2017-12-01

Since 2009 Ocean Networks Canada provides permanent access and continuous data in near real-time from two prominent gas hydrates research sites at the Northern Cascadia Margin, Barkley Canyon and Clayoquot Slope off Vancouver Island, through power and communication cables directly from shore. We show data highlights from the seafloor crawler Wally, the world's first internet operated vehicle, in a field of hydrate mounds and outcropping gas hydrates, and its co-located sonars and state-of-the-ocean sensors and Barkley Canyon. For example, spectacular views from the benthic communities and their changes over time are captured by video. At Clayoquot Slope highly active gas seep fields are monitored with a rotating multibeam sonar and various other environmental sensors. In addition, newly installed geodetic sensors as well as an instrumented borehole in that area are now online and provide additional data on subduction-related deformation and potential links to gas discharge. These show-case examples highlight the benefits of co-located experiments that enable interdisciplinary research and also the ability for high-power and -bandwidth long-term monitoring at remote seafloor locations, that over time will provide baselines for environmental monitoring together with natural variability and potential long-term trends.

Report On Fiducial Points At The Space Geodesy Based Cagliari Astronomical Observatory

NASA Astrophysics Data System (ADS)

Banni, A.; Buffa, F.; Falchi, E.; Sanna, G.

At the present time two research groups are engaged to space-geodesy activities in Sardinia: a staff belonging to the Stazione Astronomica of Cagliari (SAC) and the To- pography Section of the Dipartimento di Ingegneria Strutturale (DIST) of the Cagliari University. The two groups have a share in international campaigns and services. The local structure, consists of permanent stations of satellite observation both on radio and laser techniques. Particularly in the Cagliari Observatory a Satellite Laser Ranging system runs with nearly daily, low, medium and high orbit satellite tracking capability (e. g. Topex, Ajisai, Lageos1/2, Glonass); up to this time the Cagliari laser station has contributed towards the following international campaigns/organizations. Besides in the Observatory's site a fixed GPS system, belonging the Italian Space Agency GPS- Network and to the IGS-Network; and a GPS+GLONASS system, acquired by DIST and belonging to the IGLOS are installed and managed. All the above stations are furnished with meteorological sensors with RINEX format data dissemination avail- ability. Moreover a new 64 meters dish radio telescope (Sardinian Radio Telescope), geodetic VLBI equipped, is under construction not long away from the Observatory. The poster fully shows the facilities and furnishes a complete report on the mark- ers eccentricities, allowing co-location of the different space techniques operating in Sardinia.

Satellite Geodetic Constraints On Earthquake Processes: Implications of the 1999 Turkish Earthquakes for Fault Mechanics and Seismic Hazards on the San Andreas Fault

NASA Technical Reports Server (NTRS)

Reilinger, Robert

2005-01-01

Our principal activities during the initial phase of this project include: 1) Continued monitoring of postseismic deformation for the 1999 Izmit and Duzce, Turkey earthquakes from repeated GPS survey measurements and expansion of the Marmara Continuous GPS Network (MAGNET), 2) Establishing three North Anatolian fault crossing profiles (10 sitedprofile) at locations that experienced major surface-fault earthquakes at different times in the past to examine strain accumulation as a function of time in the earthquake cycle (2004), 3) Repeat observations of selected sites in the fault-crossing profiles (2005), 4) Repeat surveys of the Marmara GPS network to continue to monitor postseismic deformation, 5) Refining block models for the Marmara Sea seismic gap area to better understand earthquake hazards in the Greater Istanbul area, 6) Continuing development of models for afterslip and distributed viscoelastic deformation for the earthquake cycle. We are keeping close contact with MIT colleagues (Brad Hager, and Eric Hetland) who are developing models for S. California and for the earthquake cycle in general (Hetland, 2006). In addition, our Turkish partners at the Marmara Research Center have undertaken repeat, micro-gravity measurements at the MAGNET sites and have provided us estimates of gravity change during the period 2003 - 2005.

Development of a composite geodetic structure for space construction, phase 1A

NASA Technical Reports Server (NTRS)

1980-01-01

The development of a geodetic beam and beam builder for on orbit construction of large truss type space structures is discussed. The geodetic beam is a lightweight, open lattice structure composed of an equilateral gridwork of crisscrossing rods. The beam provides a high degree of stiffness and minimizes structural distortion, due to temperature gradients, through the incorporation of a new graphite and glass reinforced thermoplastic composite material with a low coefficient of thermal expansion. A low power consuming, high production rate, beam builder automatically fabricates the geodetic beams in space using rods preprocessed on Earth. Three areas of the development are focused upon; (1) geodetic beam designs for local attachment of equipment or beam to beam joining in a parallel or crossing configurations, (2) evaluation of long life pultruded rods capable of service temperatures higher than possible with the HMS/P1700 rod material, and (3) evalaution of high temperature joint encapsulant materials.

Interaction of marine geodesy, satellite technology and ocean physics

NASA Technical Reports Server (NTRS)

Mourad, A. G.; Fubara, D. M. J.

1972-01-01

The possible applications of satellite technology in marine geodesy and geodetic related ocean physics were investigated. Four major problems were identified in the areas of geodesy and ocean physics: (1) geodetic positioning and control establishment; (2) sea surface topography and geoid determination; (3) geodetic applications to ocean physics; and (4) ground truth establishment. It was found that satellite technology can play a major role in their solution. For solution of the first problem, the use of satellite geodetic techniques, such as Doppler and C-band radar ranging, is demonstrated to fix the three-dimensional coordinates of marine geodetic control if multi-satellite passes are used. The second problem is shown to require the use of satellite altimetry, along with accurate knowledge of ocean-dynamics parameters such as sea state, ocean tides, and mean sea level. The use of both conventional and advanced satellite techniques appeared to be necessary to solve the third and fourth problems.

New insights into the magma chamber activity under Mauna Loa inferred from SBAS-InSAR and geodetic inversion modelling

NASA Astrophysics Data System (ADS)

Varugu, B. K.; Amelung, F.

2017-12-01

Mauna Loa volcano, located on the Big Island, Hawaii, is the largest volcano on the earth and historically been one of the most active volcanoes on the earth. Since its last eruption in 1984, there was a decrease in the magmatic activity, yet episodic inflations with increased seismicity sparks interests in the scientific community and there is strong need to monitor the volcano with growing infrastructure close to the flanks of the volcano. Geodetic modelling of the previous inflations illustrate that the magma activity is due to inflation of hydraulically connected dike and magma chamber located from 4-8km beneath the summit (Amelung et al. 2007). Most of the seismicity observed on Mauna Loa is due to the movement along a decollement fault situated at the base of the volcano. Magma inflation under Mauna Loa has started again during the last quarter of 2013 and is continuing still with an increased seismicity. In this study, we used 140 images form COSMO SkyMED between 2013-2017 to derive and model the ground deformation. We carried out time series InSAR analysis using Small Baseline (SB) approach. While the deformation pattern seems similar in many ways to the previous inflation periods, geodetic modelling for inversion of source parameters indicate a significant propagation of the dike ( 1 km) into the South West Rift Zone(SWRZ) and a decreased depth of the dike top from summit, compared to the previous inflations. Such propagation needs to be studied further in view of the steep slope of SWRZ. In understanding the dynamics of this propagating dike, we also observed an increased seismic activity since 2014 in the vicinity of the modelled dike. Here in this study we attempt to characterize the stresses induced by the propagating dike and seaward slipping movement along the basal decollement, to explain the increased seismicity using a finite element model.

Assessment of 3D hydrologic deformation using GRACE and GPS

NASA Astrophysics Data System (ADS)

Watson, C. S.; Tregoning, P.; Fleming, K.; Burgette, R. J.; Featherstone, W. E.; Awange, J.; Kuhn, M.; Ramillien, G.

2009-12-01

Hydrological processes cause variations in gravitational potential and surface deformations, both of which are detectable with ever increasing precision using space geodetic techniques. By comparing the elastic deformation computed from continental water load estimates derived from the Gravity Recovery and Climate Experiment (GRACE), with three-dimensional surface deformation derived from GPS observations, there is clear potential to better understand global to regional hydrological processes, in addition to acquiring further insight into the systematic error contributions affecting each space geodetic technique. In this study, we compare elastic deformation derived from water load estimates taken from the CNES, CSR, GFZ and JPL time variable GRACE fields. We compare these surface displacements with those derived at a global network of GPS sites that have been homogeneously reprocessed in the GAMIT/GLOBK suite. We extend our comparison to include a series of different GPS solutions, with each solution only subtly different based on the methodology used to down weight the height component in realizing site coordinates on the terrestrial reference frame. Each of the GPS solutions incorporate modeling of atmospheric loading and utilization of the VMF1 and a priori zenith hydrostatic delays derived via ray tracing through ECMWF meteorological fields. The agreement between GRACE and GPS derived deformations is not limited to the vertical component, with excellent agreement in the horizontal component across areas where large hydrologic signals occur over broad spatial scales (with correlation in horizontal components as high as 0.9). Agreement is also observed at smaller scales, including across Europe. These comparisons assist in understanding the magnitude of current error contributions within both space geodetic techniques. With the emergence of homogeneously reprocessed GPS time series spanning the GRACE mission, this technique offers one possible means of validating the amplitude and phase of quasi-periodic signals present in GPS time series.

Monte Carlo Simulations for VLBI2010

NASA Astrophysics Data System (ADS)

Wresnik, J.; Böhm, J.; Schuh, H.

2007-07-01

Monte Carlo simulations are carried out at the Institute of Geodesy and Geophysics (IGG), Vienna, and at Goddard Space Flight Center (GSFC), Greenbelt (USA), with the goal to design a new geodetic Very Long Baseline Interferometry (VLBI) system. Influences of the schedule, the network geometry and the main stochastic processes on the geodetic results are investigated. Therefore schedules are prepared with the software package SKED (Vandenberg 1999), and different strategies are applied to produce temporally very dense schedules which are compared in terms of baseline length repeatabilities. For the simulation of VLBI observations a Monte Carlo Simulator was set up which creates artificial observations by randomly simulating wet zenith delay and clock values as well as additive white noise representing the antenna errors. For the simulation at IGG the VLBI analysis software OCCAM (Titov et al. 2004) was adapted. Random walk processes with power spectrum densities of 0.7 and 0.1 psec2/sec are used for the simulation of wet zenith delays. The clocks are simulated with Allan Standard Deviations of 1*10^-14 @ 50 min and 2*10^-15 @ 15 min and three levels of white noise, 4 psec, 8 psec and, 16 psec, are added to the artificial observations. The variations of the power spectrum densities of the clocks and wet zenith delays, and the application of different white noise levels show clearly that the wet delay is the critical factor for the improvement of the geodetic VLBI system. At GSFC the software CalcSolve is used for the VLBI analysis, therefore a comparison between the software packages OCCAM and CalcSolve was done with simulated data. For further simulations the wet zenith delay was modeled by a turbulence model. This data was provided by Nilsson T. and was added to the simulation work. Different schedules have been run.

Confirmation of Arabia plate slow motion by new GPS data in Yemen

NASA Astrophysics Data System (ADS)

Vigny, Christophe; Huchon, Philippe; Ruegg, Jean-Claude; Khanbari, Khaled; Asfaw, Laike M.

2006-02-01

During the last 10 years, a network of about 30 GPS sites was measured in Djibouti, East Africa. Additional points were also measured in Yemen, Oman, Ethiopia, Iran, and on La Réunion island. Merged with data from the available International GPS Service permanent stations scattered on the different plates in the area (Eurasia, Anatolia, Africa, Arabia, Somalia), this unique data set provides new insight on the current deformation in the Africa-Somalia-Arabia triple junction area and on the Arabian plate motion. Here we show that coherent motions of points in Yemen, Bahrain, Oman, and Iran allow us to estimate a geodetically constrained angular velocity for the Arabian plate (52.59°N, 15.74°W, 0.461°/Myr in ITRF2000). This result differs significantly from earlier determinations and is based upon our vectors in Yemen. They provide new additional data and better geometry for angular velocity determination. Combined with the African and Somalian motions, this new angular velocity results in predicted spreading rates in the Red Sea and the Gulf of Aden which are 15-20% lower than those measured from oceanic magnetic anomalies and thus averaged over the last 3 Myr. With respect to Eurasia, the geodetic motion of Arabia is also about 30% slower than predicted by NUVEL-1A. On the basis of the kinematic results presented here and on other evidence for a similar slower geodetic rate of the Indian plate, we suggest that the whole collision zone between Africa, Arabia, India on one hand and Eurasia on the other hand has slowed down in the last 3 Myr.

Imaging Small-scale Seafloor and Sub-seafloor Tectonic Fabric Using Satellite Altimetry

NASA Astrophysics Data System (ADS)

Sandwell, D. T.; Müller, D.; Matthews, K. J.; Smith, W. H. F.

2017-12-01

Marine gravity anomalies derived from satellite radar altimetry now provide an unprecedented resolution of about 7 km for mapping small-scale seafloor and sub-seafloor tectonic fabric. These gravity maps are improving rapidly because three satellite altimeters are currently collecting data with dense track coverage: (1) CryoSat-2 has routinely collected altimetry data over ice, land, and ocean since July 2010. The satellite has a long 369-day repeat cycle resulting in an average ground track spacing of 3.5 km at the equator. To date it has completed more than 7 geodetic mappings of the ocean surface. (2) The SARAL AltiKa altimeter began a non-repeat orbit phase in July 2016. AltiKa has a new Ka-band instrument with a factor of 2 better range precision than all previous altimeters. (3) Jason-2 was placed in a geodetic orbit starting July 2017. It has lower inclination coverage to provide improved gravity recovery for N-S trending anomalies. These data combined with sparse soundings will provide a dramatic improvement in predicted bathymetry and thus help guide future deep ocean surveys. The most recent global marine gravity anomaly map based on these geodetic mission data with 2-pass retracking for optimal range precision has an accuracy that is 2-4 times better than the maps derived from Geosat and ERS-1. The new data reveal the detailed fabric of fracture zones, previously unmapped, now extinct oceanic microplates in the central Pacific, and fault networks buried beneath thick sediments along continental margins. By combining satellite altimetry with marine magnetic anomalies and seafloor age dates from rock samples we are able to pinpoint the geometry and age of major plate reorganizations, particularly the enigmatic 100 Ma event, which occurred during the Cretaceous Magnetic Superchron.

VLBI real-time analysis by Kalman Filtering

NASA Astrophysics Data System (ADS)

Karbon, M.; Nilsson, T.; Soja, B.; Heinkelmann, R.; Raposo-Pulido, V.; Schuh, H.

2013-12-01

Geodetic Very Long Baseline Interferometry (VLBI) is one of the primary space geodetic techniques providing the full set of Earth Orientation Parameter (EOP) and is unique for observing long term Universal Time (UT1) and precession/nutation. Accurate and continuous EOP obtained in near real-time are essential for satellite based navigation and positioning and for enabling the precise tracking of interplanetary spacecrafts. To meet this necessity the International VLBI Service for Geodesy and Astrometry (IVS) increased its efforts to reduce the time span between the VLBI observations and the availability of the final results. Currently the timeliness is about two weeks, but the goal is to reduce it to less than one day with the future VGOS (VLBI2010 Global Observing System) network. The FWF project VLBI-ART contributes to this new generation VLBI system by considerably accelerating the VLBI analysis procedure through the implementation of an elaborate Kalman filter. This true real-time Kalman filter will be embedded in the Vienna VLBI Software (VieVS) as a completely automated tool with no need of human interaction. This filter also allows the prediction and combination of EOP from various space geodetic techniques by implementing stochastic models to statistically account for unpredictable changes in EOP. Additionally, atmospheric angular momenta calculated from numerical weather prediction models are introduced to support the short-term EOP prediction. To optimize the performance of the new software various investigations with real as well as simulated data are foreseen. The results are compared to the ones obtained by conventional VLBI parameter estimation methods (e.g. least squares method) and to corresponding parameter series from other techniques, such as from the Global Navigation Satellite Systems (GNSS).

The OSU 275 system of satellite tracking station coordinates

NASA Technical Reports Server (NTRS)

Mueller, I. I.; Kumar, M.

1975-01-01

A brief review of the methods and data used in the OSU 275 geodetic system is given along with the summary of the results. Survey information regarding the tracking stations in the system is given in tabular form along with the geodetic and geophysical parameters, origin and orientation, Cartisian coordinates, and systematic differences with global and nonglobal geodetic systems.

Development of a Mathematical Model to Assess the Accuracy of Difference between Geodetic Heights

ERIC Educational Resources Information Center

Gairabekov, Ibragim; Kliushin, Evgenii; Gayrabekov, Magomed-Bashir; Ibragimova, Elina; Gayrabekova, Amina

2016-01-01

The article includes the results of theoretical studies of the accuracy of geodetic height survey and marks points on the Earth's surface using satellite technology. The dependence of the average square error of geodetic heights difference survey from the distance to the base point was detected. It is being proved that by using satellite…

The Geodetic Signature of the Earthquake Cycle at Subduction Zones: Model Constraints on the Deep Processes

NASA Astrophysics Data System (ADS)

Govers, R.; Furlong, K. P.; van de Wiel, L.; Herman, M. W.; Broerse, T.

2018-03-01

Recent megathrust events in Tohoku (Japan), Maule (Chile), and Sumatra (Indonesia) were well recorded. Much has been learned about the dominant physical processes in megathrust zones: (partial) locking of the plate interface, detailed coseismic slip, relocking, afterslip, viscoelastic mantle relaxation, and interseismic loading. These and older observations show complex spatial and temporal patterns in crustal deformation and displacement, and significant differences among different margins. A key question is whether these differences reflect variations in the underlying processes, like differences in locking, or the margin geometry, or whether they are a consequence of the stage in the earthquake cycle of the margin. Quantitative models can connect these plate boundary processes to surficial and far-field observations. We use relatively simple, cyclic geodynamic models to isolate the first-order geodetic signature of the megathrust cycle. Coseismic and subsequent slip on the subduction interface is dynamically (and consistently) driven. A review of global preseismic, coseismic, and postseismic geodetic observations, and of their fit to the model predictions, indicates that similar physical processes are active at different margins. Most of the observed variability between the individual margins appears to be controlled by their different stages in the earthquake cycle. The modeling results also provide a possible explanation for observations of tensile faulting aftershocks and tensile cracking of the overriding plate, which are puzzling in the context of convergence/compression. From the inversion of our synthetic GNSS velocities we find that geodetic observations may incorrectly suggest weak locking of some margins, for example, the west Aleutian margin.

KALREF—A Kalman filter and time series approach to the International Terrestrial Reference Frame realization

NASA Astrophysics Data System (ADS)

Wu, Xiaoping; Abbondanza, Claudio; Altamimi, Zuheir; Chin, T. Mike; Collilieux, Xavier; Gross, Richard S.; Heflin, Michael B.; Jiang, Yan; Parker, Jay W.

2015-05-01

The current International Terrestrial Reference Frame is based on a piecewise linear site motion model and realized by reference epoch coordinates and velocities for a global set of stations. Although linear motions due to tectonic plates and glacial isostatic adjustment dominate geodetic signals, at today's millimeter precisions, nonlinear motions due to earthquakes, volcanic activities, ice mass losses, sea level rise, hydrological changes, and other processes become significant. Monitoring these (sometimes rapid) changes desires consistent and precise realization of the terrestrial reference frame (TRF) quasi-instantaneously. Here, we use a Kalman filter and smoother approach to combine time series from four space geodetic techniques to realize an experimental TRF through weekly time series of geocentric coordinates. In addition to secular, periodic, and stochastic components for station coordinates, the Kalman filter state variables also include daily Earth orientation parameters and transformation parameters from input data frames to the combined TRF. Local tie measurements among colocated stations are used at their known or nominal epochs of observation, with comotion constraints applied to almost all colocated stations. The filter/smoother approach unifies different geodetic time series in a single geocentric frame. Fragmented and multitechnique tracking records at colocation sites are bridged together to form longer and coherent motion time series. While the time series approach to TRF reflects the reality of a changing Earth more closely than the linear approximation model, the filter/smoother is computationally powerful and flexible to facilitate incorporation of other data types and more advanced characterization of stochastic behavior of geodetic time series.

Debris flow cartography using differential GNSS and Theodolite measurements

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Guinau, Marta; Calvet, Jaume; Furdada, Gloria; Victoriano, Ane; Génova, Mar; Suriñach, Emma

2016-04-01

The presented results form part of a CHARMA project, which pursues a broad objective of reducing damage caused by uncontrolled mass movements, such as rockfalls, snow avalanches and debris flows. Ultimate goal of the project is to contribute towards the establishment of new scientific knowledge and tools that can help in the design and creation of early warning systems. Here we present the specific results that deal with the application of differential GNSS and classical geodetic (e.g. theodolite) methods for mapping debris and torrential flows. Specifically, we investigate the Portainé stream located in the Pallars Sobirà region of Catalonia (Spain), in the eastern Pyrenees. In the last decade more than ten debris-flow type phenomena have affected the region, causing considerable economic losses. Since early 2014, we have conducted several field campaigns within the study area, where we have employed a multi-disciplinary approach, consisting of geomorphological, dendro-chronological and geodetic methods, in order to map the river bed and reconstruct the history of the extreme flooding and debris flow events. Geodetic studies included several approaches, using the classical and satellite based methods. The former consisted of angle and distance measurements between the Geodolite 502 total station and the reflecting prisms placed on top of the control points located within the riverbed. These type of measurements are precise, although present several disadvantages such as the lack of absolute coordinates that makes the geo-referencing difficult, as well as a relatively time-consuming process that involves two persons. For this reason, we have also measured the same control points using the differential GNSS system, in order to evaluate the feasibility of replacing the total station measurements with the GNSS. The latter measuring method is fast and can be conducted by one person. However, the fact that the study area is within the riverbed, often below the trees, limits the visibility of the satellites and thus, can result in meter-level errors while estimating the positions. We have conducted 2 measurements using various differential GNSS systems in March and in September of 2015. During these measurements we used Leica Viva GS14 receiver as a rover station, which was equipped with a GSM card to establish an internet connection in order to receive differential corrections from continuous GNSS networks. During the first campaign we have used the RTK positioning method using the SmartNet network (http://es.smartnet-eu.com) operated by Leica. This system had the advantage of transmitting differential corrections for GPS and GLONASS systems. During the second campaign, we have had an access to the ICGC (http://www.icc.cat) CatNet permanent GPS network, which only provides GPS satellite corrections. Here we present the analysis of the obtained precisions from these two RTK systems. Additionally, we have analyzed the geodetic data in a post-processing mode using the Leica Geo Office 8.4 software with IGS estimated final orbits. For this procedure, in addition to using the data from nearby CatNet CGPS stations, we have also used data from the base station(s) specifically setup near the study area during the campaign period. The work has been supported by the Spanish Ministry of Science and Innovation project CHARMA: CHAracterization and ContRol of MAss Movements. A Challenge for Geohazard Mitigation (CGL2013-40828-R) and RISKNAT group (2014GR/1243).

New step toward geodetic range observations at the sea floor with the BBOBS system

NASA Astrophysics Data System (ADS)

Shiobara, H.; Shinohara, M.; Isse, T.

2011-12-01

Since 1999, we had developed the broadband ocean bottom seismometer (BBOBS) and its new generation model (BBOBS-NX), and performed several practical observations with them in these ten years to create a category of the ocean floor broadband seismology. Now, the BBOBS data is proved to be acceptable for broadband seismic analyses. In these studies, the period range of the data used is about 10 - 200 s, but in longer period range, i.e. geodetic range, is an unknown region in observations at the sea floor. The acoustic GPS link observation is one of successful methods to know horizontal movement of the sea floor, but it is difficult to obtain continuous data in time. The borehole tilt-meter system is ideal in observational conditions, but it is impossible to expand spatially dense observation network. On the other hand, high mobility of our BBOBS and BBOBS-NX can be a breakthrough for this kind of observation network. So that, based on our BBOBS technology, two kinds of attempts to expand observation range toward the geodetic one have been started since 2009. Our aim in these attempts is to extend observation periods more than one week long for detecting slow slip events, as a first step. Finally, we would like to build the observation network by using them. The first attempt is a precise pressure measurement to detect vertical displacement at the sea floor by attaching an absolute pressure gauge and a parasitic data logger to the original OBS data recorder. The stable frequency oscillator (MCXO) in the data recorder is useful for precise pressure measurement of the gauge with frequency outputs. Although the final resolution of the pressure becomes smaller than 1 Pa, we still have problems due to the drift of the gauge and some scale of sea level change in practical observations. The total precision of the pressure value is also affected by the shift and drift of the frequency standard to measure frequency output signals of the gauge. In our measurements, this effect is estimated less than 60 Pa from the maximum frequency deviation of the MCXO, but it will be negligible by using a small chip scale atomic clock (CSAC), which is available now, as the frequency standard. The second one is a tilt observation just beneath the sea floor by using the BBOBS-NX system, which had been tested 6 times in 2008 - 2010 by free falling deployment with appropriate penetration to the sea floor sediment. The tilt is measured by using two horizontal mass position (acceleration) signals of the broadband sensor. The noise reduction ratio in horizontal components of the BBOBS-NX compared with those of the BBOBS staying on the sea floor is more than 10 in the period range longer than 10 s. It means the possibility of the BBOBS-NX system for the tilt observation in the geodetic range. As we didn't record the mass position signal continuously, a test observation was performed by using the same sensor of the BBOBS-NX at the ERI's Nokogiriyama observatory in 2010. The result is comparable with that of the water tube tilt-meter there in the diurnal Earth tide range. In July 2011, we started a test observation of the tilt measurement at the sea floor SE off Kii peninsula by using the BBOBS-NX as the feasibility study. The deployment was ideally performed by the ROV, and the recovery is planned in January 2012.

The integration of stress, strain, and seismogenic fault data: towards more robust estimates of the earthquake potential in Italy and its surroundings

NASA Astrophysics Data System (ADS)

Caporali, Alessandro; Braitenberg, Carla; Burrato, Pierfrancesco; Carafa, Michele; Di Giovambattista, Rita; Gentili, Stefania; Mariucci, Maria Teresa; Montone, Paola; Morsut, Federico; Nicolini, Luca; Pivetta, Tommaso; Roselli, Pamela; Rossi, Giuliana; Valensise, Gian Luca; Vigano, Alfio

2016-04-01

Italy is an earthquake-prone country with a long tradition in observational seismology. For many years, the country's unique historical earthquake record has revealed fundamental properties of Italian seismicity and has been used to determine earthquake rates. Paleoseismological studies conducted over the past 20 years have shown that the length of this record - 5 to 8 centuries, depending on areas - is just a fraction of the typical recurrence interval of Italian faults - consistently larger than a millennium. Hence, so far the earthquake potential may have been significantly over- or under-estimated. Based on a clear perception of these circumstances, over the past two decades large networks and datasets describing independent aspects of the seismic cycle have been developed. INGV, OGS, some universities and local administrations have built networks that globally include nearly 500 permanent GPS/GNSS sites, routinely used to compute accurate horizontal velocity gradients reflecting the accumulation of tectonic strain. INGV developed the Italian present-day stress map, which includes over 700 datapoints based on geophysical in-situ measurements and fault plane solutions, and the Database of Individual Seismogenic Sources (DISS), a unique compilation featuring nearly 300 three-dimensional seismogenic faults over the entire nation. INGV also updates and maintains the Catalogo Parametrico dei Terremoti Italiani (CPTI) and the instrumental earthquake database ISIDe, whereas OGS operates its own seismic catalogue for northeastern Italy. We present preliminary results on the use of this wealth of homogeneously collected and updated observations of stress and strain as a source of loading/unloading of the faults listed in the DISS database. We use the geodetic strain rate - after converting it to stress rate in conjunction with the geophysical stress data of the Stress Map - to compute the Coulomb Failure Function on all fault planes described by the DISS database. This may be seen as an indicator of the rate at which the regional stress is transferred to each fault; as its sign can be positive or negative, the Coulomb Failure Function rate should ultimately indicate the rate at which every fault for which sufficient geodetic data are available is loading or unloading elastic energy. A better understanding of the relationships among geodetically-documented strains, present-day stress, active faulting and seismicity for the entire country should enable us to outline regions where the current strains explain well the known seismicity and to single out areas where stress is consistently building up but are historically quiescent. In such areas the lack of seismicity may result from a limited earthquake coupling - i.e. current strains are consumed aseismically - or from the incompleteness of the earthquake record. Our results may ultimately contribute to the assessment of time-dependent seismic hazard in Italy, thus complementing the time-independent approach used for conventional seismic hazard maps.

Probabilistic Seismic Hazard Maps for Ecuador

NASA Astrophysics Data System (ADS)

Mariniere, J.; Beauval, C.; Yepes, H. A.; Laurence, A.; Nocquet, J. M.; Alvarado, A. P.; Baize, S.; Aguilar, J.; Singaucho, J. C.; Jomard, H.

2017-12-01

A probabilistic seismic hazard study is led for Ecuador, a country facing a high seismic hazard, both from megathrust subduction earthquakes and shallow crustal moderate to large earthquakes. Building on the knowledge produced in the last years in historical seismicity, earthquake catalogs, active tectonics, geodynamics, and geodesy, several alternative earthquake recurrence models are developed. An area source model is first proposed, based on the seismogenic crustal and inslab sources defined in Yepes et al. (2016). A slightly different segmentation is proposed for the subduction interface, with respect to Yepes et al. (2016). Three earthquake catalogs are used to account for the numerous uncertainties in the modeling of frequency-magnitude distributions. The hazard maps obtained highlight several source zones enclosing fault systems that exhibit low seismic activity, not representative of the geological and/or geodetical slip rates. Consequently, a fault model is derived, including faults with an earthquake recurrence model inferred from geological and/or geodetical slip rate estimates. The geodetical slip rates on the set of simplified faults are estimated from a GPS horizontal velocity field (Nocquet et al. 2014). Assumptions on the aseismic component of the deformation are required. Combining these alternative earthquake models in a logic tree, and using a set of selected ground-motion prediction equations adapted to Ecuador's different tectonic contexts, a mean hazard map is obtained. Hazard maps corresponding to the percentiles 16 and 84% are also derived, highlighting the zones where uncertainties on the hazard are highest.

Foundational Data Products for Europa: A Planetary Spatial Data Infrastructure Example

NASA Astrophysics Data System (ADS)

Archinal, B. A.; Laura, J.; Becker, T. L.; Bland, M. T.; Kirk, R. L.

2017-12-01

Any Spatial Data Infrastructure (SDI), including a Planetary SDI (PSDI [1]), includes primary components such as "policy, access network, technical standards, people (including partnerships), and data" [2]. Data is largely categorized into critical foundational products and framework data products. Of data themes [3] previously identified for the U. S. National SDI, we identify [4] three types of products that are foundational to a PSDI: geodetic coordinate reference systems, elevation information, and orthomosaics. We previously listed examples of such products for the Moon (ibid.). Here, we list the current state of these three foundational products for Europa, a key destination in the outer Solar System. Geodetic coordinate reference systems for Europa are based on photogrammetric control networks generated from processing of Voyager and Galileo images, the most recent being that created by M. Davies and T. Colvin at The RAND Corporation in the late 1990s. The Voyager and Galileo images provide insufficient stereo coverage to derive a detailed global topographic model, but various global ellipsoidal shape models have been derived using e.g. the RAND network or limb profile data. The best-known global mosaic of Europa is a controlled orthomosaic produced by the U.S. Geological Survey [5], based on the RAND network and triaxial ellipsoid shape model. Near future needs include comparing the resolution and accuracy of these products with estimates for newer products that might supersede them, including released or unreleased regional products (such as digital terrain models or mosaics) and products that could be made by processing of extant data. Understanding these PSDI fundamental needs will also improve assessing and prioritizing products that are planned for by the upcoming NASA Europa Clipper mission. This effort is not only useful for Europa science, but is also a first step toward developing such summaries for all Solar System bodies with relevant data, which collectively will serve as a foundation of an entire PSDI. References: [1] Laura et al., ISPRS J. Geo-Info., 6, #181. [2] Rajabifard and Williamson, in Williamson and Rajabifard, eds., ISPRS-WG IV/8, Hong Kong, China, Ch. 6, 2001. [3] OMB Circular A-16 Supp. Guidance. [4] LPS XLVIII, #2286. [5] USGS map I-2757.

First Vertical Land Movement Estimates on South Georgia Island: An Impact Study on Sea Level Change from Tide Gauge and Satellite Altimetry Measurements

NASA Astrophysics Data System (ADS)

Abraha, K. E.; Teferle, F. N.; Hunegnaw, A.; Woodworth, P. L.; Williams, S. D. P.; Hibbert, A.; Smalley, R., Jr.; Dalziel, I.; Lawver, L.

2017-12-01

South Georgia Island in the Southern Atlantic Ocean has been a key location for the seismic, geomagnetic and oceanic global monitoring networks. However, no permanent geodetic monitoring station had been established there despite the lack of observations from this region within, for example, the International GNSS Service (IGS) network of Global Navigation Satellite System (GNSS) stations. Then, in 2013 the King Edward Point (KEP) Geodetic Observatory was established with a focus on sea level studies and in support of general geoscience applications. Currently, this observatory located roughly half-way along the main island along its northern coastline, consists of two GNSS stations (KEPA and KRSA) with local benchmark networks, allowing the height determinations from the GNSS antennas to be transferred to the KEP tide gauge (GLOSS ID 187) and forming a height reference within the International Terrestrial Reference Frame. In late 2014, three additional GNSS stations (SG01, SG02 and SG03) were established, all located on small islands at the perimeter of the main island. Together the stations provide the best possible geographic distribution to study various geophysical processes in the region. With the GNSS-derived position time series now partly reaching over 4.5 years in length, it has become possible to provide first estimates of vertical land movements for the island and, in particular, KEP with its surrounding area. Together with four precise levelling campaigns of the benchmark network in 2013, 2014 and two in 2017, it has also been possible to investigate the very local character of the vertical motions, ie. the stability of the jetty upon which the tide gauge is mounted. Our measurements show that while South Georgia Island and the area around KEP are rising, the jetty and tide gauge are subsiding. In this study, we will present the preliminary results from the GNSS and levelling measurements and will discuss their impact on the sea level record from the KEP tide gauge which is ideally situated in a mid-ocean location for satellite altimetry calibration over the Southern Atlantic and Southern Oceans.

Studying the active deformation of distributed plate boundaries by integration of GNSS networks

NASA Astrophysics Data System (ADS)

D'Agostino, Nicola; Avallone, Antonio; Cecere, Gianpaolo; D'Anastasio, Elisabetta

2013-04-01

In the last decade GNSS networks installed for different purposes have proliferated in Italy and now provide a large amount of data available to geophysical studies. In addition to the existing regional and nation-wide scientific GNSS networks developed by ASI (http://geodaf.mt.asi.it), INGV (http://ring.gm.ingv.it) and OGS (http://crs.inogs.it/frednet), a large number (> 400) of continuously-operating GPS stations have been installed in the framework of regional and national networks, both publicly-operated and commercial, developed to provide real-time positioning capability to surveyors. Although the quality of the data and metadata associated to these stations is generally lower with respect to the "scientific" CGPS stations, the increased density and redundancy in crustal motion information, resulting in more than 500 stations with more than 2.5 years of observations, significantly increase the knowledge of the active deformation of the Italian territory and provides a unique image of the crustal deformation field. The obtained GPS velocity field is analysed and various features ranging from the definition of strain distribution and microplate kinematics within the plate boundary, to the evaluation of tectonic strain accumulation on active faults are presented in this work. Undeforming, aseismic regions (Sardinia, Southern Apulia) provide test sites to evaluate the lower bound on the accuracy achievable to measure tectonic deformation. Integration of GNSS networks significantly improves the resolution of the strain rate field in Central Italy showing that active deformation is concentrated in a narrow belt along the crest of the Apennines, consistently with the distribution of the largest historical and recent earthquakes. Products derived from dense GPS velocity and strain rate fields include map of earthquake potential developed under the assumption that the rate of seismic moment accumulation measured from geodesy distributes into earthquake sizes that follow a truncated Gutenberg-Richter distribution of given b-value and Mmax. The advantage is that, being purely strain-rate based, geodetic models of earthquake potentials require few subjective constraints. In addition, the maps have well-defined error bounds and the approach may apply over regions where poor fault informations are available. This approach provides independent verification of the rates of deformation in regions where geologists have documented faults and allows to evaluate the consistency of the contemporary deformation field and the historical earthquake record. We believe that GNSS networks integration represents an important reality in the framework of the EPOS infrastructure and we strongly support the idea of an European research approach to data sharing among the scientific community.

Aftershock distribution as a constraint on the geodetic model of coseismic slip for the 2004 Parkfield earthquake

USGS Publications Warehouse

Bennington, Ninfa; Thurber, Clifford; Feigl, Kurt; ,

2011-01-01

Several studies of the 2004 Parkfield earthquake have linked the spatial distribution of the event’s aftershocks to the mainshock slip distribution on the fault. Using geodetic data, we find a model of coseismic slip for the 2004 Parkfield earthquake with the constraint that the edges of coseismic slip patches align with aftershocks. The constraint is applied by encouraging the curvature of coseismic slip in each model cell to be equal to the negative of the curvature of seismicity density. The large patch of peak slip about 15 km northwest of the 2004 hypocenter found in the curvature-constrained model is in good agreement in location and amplitude with previous geodetic studies and the majority of strong motion studies. The curvature-constrained solution shows slip primarily between aftershock “streaks” with the continuation of moderate levels of slip to the southeast. These observations are in good agreement with strong motion studies, but inconsistent with the majority of published geodetic slip models. Southeast of the 2004 hypocenter, a patch of peak slip observed in strong motion studies is absent from our curvature-constrained model, but the available GPS data do not resolve slip in this region. We conclude that the geodetic slip model constrained by the aftershock distribution fits the geodetic data quite well and that inconsistencies between models derived from seismic and geodetic data can be attributed largely to resolution issues.

A Comparison of Geodetic and Geologic Rates Prior to Large Strike-Slip Earthquakes: A Diversity of Earthquake-Cycle Behaviors?

NASA Astrophysics Data System (ADS)

Dolan, James F.; Meade, Brendan J.

2017-12-01

Comparison of preevent geodetic and geologic rates in three large-magnitude (Mw = 7.6-7.9) strike-slip earthquakes reveals a wide range of behaviors. Specifically, geodetic rates of 26-28 mm/yr for the North Anatolian fault along the 1999 MW = 7.6 Izmit rupture are ˜40% faster than Holocene geologic rates. In contrast, geodetic rates of ˜6-8 mm/yr along the Denali fault prior to the 2002 MW = 7.9 Denali earthquake are only approximately half as fast as the latest Pleistocene-Holocene geologic rate of ˜12 mm/yr. In the third example where a sufficiently long pre-earthquake geodetic time series exists, the geodetic and geologic rates along the 2001 MW = 7.8 Kokoxili rupture on the Kunlun fault are approximately equal at ˜11 mm/yr. These results are not readily explicable with extant earthquake-cycle modeling, suggesting that they may instead be due to some combination of regional kinematic fault interactions, temporal variations in the strength of lithospheric-scale shear zones, and/or variations in local relative plate motion rate. Whatever the exact causes of these variable behaviors, these observations indicate that either the ratio of geodetic to geologic rates before an earthquake may not be diagnostic of the time to the next earthquake, as predicted by many rheologically based geodynamic models of earthquake-cycle behavior, or different behaviors characterize different fault systems in a manner that is not yet understood or predictable.

The kinematic response of Petermann Glacier, Greenland to ice shelf perturbation

NASA Astrophysics Data System (ADS)

Hubbard, A.; Box, J. E.; Bates, R.; Nick, F.; Luckman, A. J.; van de Wal, R.; Doyle, S. H.

2010-12-01

The acceleration and dynamic thinning of interior zones of the polar ice sheets due to outlet/ice shelf retreat has been identified as a factor hastening their demise and contribution to global sea-level rise. The detachment of a 275 square km area of the Petermann Glacier ice shelf in August, 2010 presents a natural experiment to investigate the timing, mechanisms and efficacy of upstream dynamic feedbacks resulting from a singular but potentially significant frontal perturbation. In 2009, a permanent geodetic/differential GPS strain network logging every 10 seconds was deployed along a 200 km longitudinal profile from the ice front across the grounding line extending into the interior of Petermann Glacier to characterize the system’s state before, during and after any such event. We present an overview of the geophysical measurements conducted and analyze the kinematics of the shelf detachment in relation to local environmental forcing. Finally, we discuss the postulated instantaneous and ongoing evolution in force-balance and concomitant dynamic response resulting from the perturbation along with its implications for Petermann's ongoing stability. Petermann Glacier GNSS base & telemetric GPS facility: community AA & rehab meet point. On ice geodetic-GPS station flat out & reading 0 Volts

Estimability of geodetic parameters from space VLBI observables

NASA Technical Reports Server (NTRS)

Adam, Jozsef

1990-01-01

The feasibility of space very long base interferometry (VLBI) observables for geodesy and geodynamics is investigated. A brief review of space VLBI systems from the point of view of potential geodetic application is given. A selected notational convention is used to jointly treat the VLBI observables of different types of baselines within a combined ground/space VLBI network. The basic equations of the space VLBI observables appropriate for convariance analysis are derived and included. The corresponding equations for the ground-to-ground baseline VLBI observables are also given for a comparison. The simplified expression of the mathematical models for both space VLBI observables (time delay and delay rate) include the ground station coordinates, the satellite orbital elements, the earth rotation parameters, the radio source coordinates, and clock parameters. The observation equations with these parameters were examined in order to determine which of them are separable or nonseparable. Singularity problems arising from coordinate system definition and critical configuration are studied. Linear dependencies between partials are analytically derived. The mathematical models for ground-space baseline VLBI observables were tested with simulation data in the frame of some numerical experiments. Singularity due to datum defect is confirmed.

Monitoring Deformation Offshore Northern Chile Using a Seafloor Geodetic Network (GeoSEA)

NASA Astrophysics Data System (ADS)

Hannemann, K.; Lange, D.; Kopp, H.; Petersen, F.; Contreras-Reyes, E.

2016-12-01

The seafloor stores crucial information on sub-seafloor processes, including stress, elastic strain, and earthquake and tsunami generation. This information may be extracted through the emerging scientific field of seafloor geodesy. The target of the GeoSEA array (Geodetic Earthquake Observatory on the SEAfloor) is to measure deformation in mm-scale between instruments located in three target areas on the marine forearc and outer rise of the North Chilean subduction zone around 21°S. This segment of the Nazca-South American plate boundary has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique/Pisagua earthquake (Mw=8.1). The southern portion of this segment is still unbroken. The GeoSEA network consists of autonomous seafloor transponders installed on 4 m high tripods. In December 2015, they were lowered to the seabed on the deep-sea cable of RV SONNE. The transponders measure acoustic distance, tilt, temperature and pressure for a period of 3.5 years. As additional component of the network, GeoSURF, a self-steering autonomous vehicle (wave glider), monitors system health and is able to upload data from the seafloor stations and to transfer it via satellite. We set up 3 subarrays with interstation distances of up to 2000 m. On the middle continental slope in 2300 m water depth, an array consisting of 8 transponders measures across crustal faults seen in AUV mapping. A second array of 5 stations located on the outer rise monitors extension across normal plate-bending faults. The deepest deployment in 5000 m water depth located on the lower continental slope with 10 stations is designed to measure diffuse strain build-up. We expect a precision of ± 4mm for each station pair. The data of 11 months will be downloaded in November 2015 during a cruise of RV Langseth and will reveal the deformation between the transponders located on the seafloor.

Geophysical Survey of the 1978 Seismo-volcanic Crisis in the Asal-Ghoubbet Rift (Afar Depression, Djibouti) and the Post-rifting Deformations

NASA Astrophysics Data System (ADS)

Doubre, C.; Ruegg, J.; de Chabalier, J.; Vigny, C.; Jacques, E.

2006-12-01

In November 1978, a seismo-volcanic crisis occurred in the Asal-Ghoubbet Rift, which is located at the western termination of the oceanic Aden Ridge propagating inland into the Afar Depression and accommodates a large part of the divergent motion of the Arabia and Somalia plates. This episode offered the opportunity to study the rifting process controlling the evolution of a sub-aerial opening segment at the transition from continental break-up to oceanic spreading. This major crustal spreading episode started with two major earthquakes in the subaerial part of the rift (mb=5.3 and 5.0) and was followed by the week-long, basaltic fissure eruption of the Ardukoba at the western tip of the central volcanic chain. The geophysical survey carried out for the crisis was possible by means of the Arta Observatory in Djibouti within the framework of field surveys financed by the French agency CNRS-INSU. This allowed the measurements of the surface breaks (dry open fissures up to 100 m, normal fault throws up to 80 cm), the crustal deformation by geodetic networks and leveling (up to 2m of horizontal widening, 70 cm of inner-floor subsidence), and the evolution of the seismic activity (eastward migration along the Aden Ridge) associated with this rifting event. Elastic modeling shows that both the deformation pattern and the seismic activity can be explained by the aseismic intrusion of two dykes below the rift inner-floor. Subsequently, a continuous geodetic and seismic monitoring has been maintained and shows that the post-dyke injection evolution of the rift is dominated by two distinct periods. During the six first years (1979-1986), high rates of horizontal opening and slip of creeping normal faults accommodate the subsidence of the inner-floor surrimposed to the development of a 25 km-wide uplift. Since 1986-87, the strain rates have decreased and currently reach values consistent with long-term velocities deduced from morpho-tectonic studies. The evolution of the deformation field deduced from geodetic and seismic data is discussed in terms of kinematic relation with creeping faults and dyking, continuous aseismic dyking injection/inflation at depth, and transient variations associated with a relaxation mechanism related to the sudden opening of dykes. An active process involving fluid migration is required to explain the discrepancy between the far field and near field velocities measured by GPS, the general doming identified by leveling data, the periods of slip acceleration along continuously creeping faults observed from InSAR data, and the time variations of low-magnitude seismicity. All these observations therefore illustrate that some parts of the crust in the rift during the rifting episode and throughout the whole post-rifting period are in a critical state close to failure.

BKG/DGFI Combination Center Annual Report 2012

NASA Technical Reports Server (NTRS)

Bachmann, Sabine; Loesler, Michael; Heinkelmann, Robert; Gerstl, Michael

2013-01-01

This report summarizes the activities of the Federal Agency for Cartography and Geodesy (Bundesamt fuer Kartographie und Geodaesie, BKG) and the German Geodetic Research Institute (Deutsches Geodaetisches Forschungsinstitut, DGFI)BKG/DGFI Combination Center in 2011 and outlines the planned activities for the year 2012. The main focus was to stabilize outlier detection and to update the Web presentation of the combined products.

The Data Base of the International Geodynamics and Earth Tide Service (IGETS)

NASA Astrophysics Data System (ADS)

Voigt, Christian; Förste, Christoph; Wziontek, Hartmut; Crossley, David; Meurers, Bruno; Pálinkáš, Vojtech; Hinderer, Jacques; Boy, Jean-Paul; Barriot, Jean-Pierre; Sun, Heping

2017-04-01

The International Geodynamics and Earth Tide Service (IGETS) was established in 2015 by the International Association of Geodesy (IAG). IGETS continues the activities of the Global Geodynamics Project (GGP, 1997-2015) to provide support to geodetic and geophysical research activities using superconducting gravimeter data within the context of an international network. The primary objective of IGETS is to provide a service for continuous ground based measurements to monitor temporal variations of the Earth's gravity field and deformation of the Earth's surface by long term records from ground gravimeters, tiltmeters, strainmeters and other geodynamic sensors. IGETS also continues the activities of the International Center for Earth Tides (ICET), in particular, in collecting, archiving and distributing Earth tide records from long series of the various geodynamic sensors. This presentation introduces the IGETS data base hosted by GFZ and accessible via http://igets.gfz-potsdam.de to the geodetic and geodynamics community as well as to all other interested data producers and users. At present, records from superconducting gravimeters at 34 stations worldwide are available. Level 1 products are raw gravity and local pressure records decimated at 1 minute samples. As a new feature, records with 1 or 2 seconds samples are already provided for a few stations. Level 2 products consist of gravity and pressure data corrected for instrumental perturbations and ready for tidal analysis, which are derived from Level 1 datasets and computed by the University of French Polynesia (Tahiti, French Polynesia). Gravity residuals after particular geophysical corrections (including solid Earth tides, polar motion, tidal and non-tidal loading effects) considered as Level 3 products are derived from Level 2 datasets and computed by EOST (Ecole et Observatoire des Sciences de la Terre, Strasbourg, France). The IGETS data sets are stored by GFZ on a FTP server and are freely available after a compulsory user registration. A major benefit of IGETS is the provision of digital object identifiers (DOI) by the research repository of GFZ Data Services for the data sets of every station. This ensures a long term storage and an increased visibility as part of an international network but also a proper data citation. At present, the IGETS data base is supported by 24 data producers providing records to almost 100 registered users. All relevant information on the data base, i.e., data availability and access, stations and sensors, conventional data formats, etc. are compiled in a specific scientific technical report (see http://doi.org/10.2312/GFZ.b103-16087). As IGETS is seeking for providing all kinds of long-term geodynamic time series, interested station operators are cordially invited to provide their data sets to the IGETS data base and, in return, benefit from being part of the IAG service IGETS.

European Plate Observing System - the Arctic dimension and the Nordic collaboration

NASA Astrophysics Data System (ADS)

Atakan, K.; Heikkinen, P.; Juhlin, C.; Thybo, H.; Vogfjord, K.

2012-04-01

Within the framework of the EPOS project, Nordic interests are significant, not only in fundamental scientific issues related to geodynamic processes, but also in terms of the application of these to several central problems such as, hydrocarbon exploration and production including the related environmental issues, CO2 storage (or other toxic waste repositories) in geological formations, geothermal energy (natural and hot-dry rock) utilization and mining, geohazards (earthquakes, landslides and volcanic eruptions) and their consequences to the society. The Arctic dimension including Fennoscandia, the northern North Atlantic and the Arctic Sea constitutes an area of considerable geographical extent within the European plate. The region also contains a significant part of the European plate boundary submerged under the North Atlantic and the Arctic sea, where geodynamic processes such as rifting and fracturing are especially energetic. In particular, where the plate boundary is exposed on land in the South Iceland seismic zone, large earthquakes are frequently observed including two Mw6.5 events in 2000 and one Mw6.3 event in 2008. But, seismic hazard is not confined to the plate boundary. Significant intra-plate earthquakes have recently occurred in the region (Mw6.1 in the continental shelf near Spitsbergen in 2008, Mw5.0 in Southern Sweden in 2008, Mw5.2 near Kaliningrad in 2004) showing that there is considerable seismic hazard in the region. In addition, submarine landslide earthquakes are always of concern due to possible tsunami generation. Volcanic activity occurs on the plate boundary and is particularly strong in the rift zones of Iceland, where on average two volcanic eruptions occur per decade. subaerial volcanic eruptions also occur on Jan Mayen island, farther north on the Mid Atlantic ridge. Together, the Danish seismic network in Greenland, the Norwegian seismic arrays and national network traversing the length of Norway and the Icelandic seismic and strong motion networks monitor seismic activity and hazard in the North Atlantic. Vigorous volcanic activity along the plate boundary in Iceland and associated hazards are monitored by the Icelandic, seismic, geodetic, meteorological and hydrological networks. Recent eruptions, like the 2010 Eyjafjallajökull eruptions have demonstrated the far-reaching hazard to aviation caused by volcanic eruptions in Iceland. The high-sensitivity seismic and geodetic networks of Sweden monitor isostatic rebound of Fennoscandia. In this context, the varied Nordic monitoring networks provide a significant contribution to the main objectives of EPOS. There are already existing links with the other ESFRI initiatives where strong Nordic participation is established, such as SIOS and EMSO. As such EPOS provides the necessary platform to collaborate and develop an important Nordic dimension in the European Research Area. There is a long tradition of collaboration at the governmental level between the Nordic countries, Norway, Sweden, Denmark, Finland and Iceland. Within the fields of research and education, the Nordic Ministries have a dedicated program, where research networks are being promoted. Recently a Nordic collaborative network in seismology, "NordQuake" (coordinated by Denmark) was established within this program. This collaboration which is now formalized and supported by the Nordic Ministries is based on a cooperation which was initiated more than 40 years ago, where annual Nordic Seminars in seismology (previously on detection seismology) was the central element. EPOS Nordic collaboration, building upon a long lasting history, has a significant potential for synergy effects in the region and therefore represents an important dimension within EPOS. Nordic EPOS Team: Lars Ottemöller (UiB), Mathilde B. Sørensen (UiB), Louise W. Bjerrum (UiB), Conrad Lindholm (Norsar), Halfdan Kjerulf (SK), Amir Kaynia (NGI), Valerie Maupin (UiO), Tor Langeland (CMR), Joerg Ebbing (NGU), John Dehls (NGU), Øystein Nordgulen (NGU), Roland Roberts (UU), Reynir Bødvarsson (UU), Ólafur Guðmundsson (UU), Steinunn Jacobsdottir (IMO), Freysteinn Sigmundsson (IES), Benedikt Halldórsson (EERC), Gudmundur Valsson (LMI), Irina Artemieva (KU), Peter Voss (GEUS), Trine Dahl-Jensen (GEUS), Tine B. Larsen (GEUS), Jens Jørgen Møller (GEUS), Martin Hansen (GEUS), Jørgen Tulstrup (GEUS), Johnny Fredericia (GEUS), Niels Andersen (DTU-Space), Jurgen Matzka (DTU-Space), Shfaqat Abbas Khan (DTU-Space), Niels Balling (AU), Markku Poutanen (FGI), Elena Kozlovskaya (SGO).

Geodetic component of the monitoring of tectonic and hydrogeological activities in Kopacki Rit Nature Park

NASA Astrophysics Data System (ADS)

Dapo, Almin; Pribicevic, Bosko

2013-04-01

Based on the European and global experience, the amplitude change in the structural arrangement caused by recent tectonic movements, can be most accurately determined by repeated precise GPS measurements on specially stabilized geodetic and geodynamic points. Because of these reasons, the GPS method to determine the movements on specially stabilized points in the Nature park Kopacki rit is also applied in this project. Kopacki rit Nature Park is the biggest preserved natural flooded area on the Danube. It is spread over 23 000 hectares between the rivers Danube and Drava and is one of the biggest fluvial wetland valleys in Europe. In 1993 it was listed as one of internationally valuable wetlands according to the Ramsar Convention. By now in Kopacki rit there have been sights of about 295 bird species, more than 400 species of invertebrates and 44 types of fish. Many of them are globally endangered species like, white tailed eagle, black stork and prairie hawk. It's not rare to come across some deer herds, wild boars or others. Today's geological and geomorphological relations in the Nature park Kopacki rit are largely the result of climate, sedimentary, tectonic and anthropogenic activity in the last 10,000 years. Unfortunately the phenomenon of the Kopacki rit Nature park is in danger to be over in the near future due to those and of course man made activities on the Danube river. It is trough scientific investigations of tectonic and hydrogeological activities that scientist from University of Zagreb are trying to contribute to wider knowledge and possible solutions to this problem. In the year 2009 the first GPS campaign was conducted, and the first set of coordinates of stabilized points was determined which can be considered zero-series measurements. In 2010 a second GPS campaign was conducted and the first set of movements on the Geodynamic Network of Kopacki Rit Nature Park was determined. Processing GPS measurements from 2009 and 2010 was carried out in a scientific software with multipoint solutions GAMIT / GLOBK, using Kalman filter to determine the velocity from discrete campaigns. This paper presents the performed measurements, processing and analysis of the results, which indicate that there are geodynamicaly significant developments.

The Hawaiian Volcano Observatory: a natural laboratory for studying basaltic volcanism: Chapter 1 in Characteristics of Hawaiian volcanoes

USGS Publications Warehouse

Tilling, Robert I.; Kauahikaua, James P.; Brantley, Steven R.; Neal, Christina A.; Poland, Michael P.; Takahashi, T. Jane; Landowski, Claire M.

2014-01-01

This chapter summarizes HVO’s history and some of the scientific achievements made possible by this permanent observatory over the past century as it grew from a small wooden structure with only a small staff and few instruments to a modern, well-staffed, world-class facility with state-of-the-art monitoring networks that constantly track volcanic and earthquake activity. The many successes of HVO, from improving basic knowledge about basaltic volcanism to providing hands-on experience and training for hundreds of scientists and students and serving as the testing ground for new instruments and technologies, stem directly from the acquisition, integration, and analysis of multiple datasets that span many decades of observations of frequent eruptive activity. HVO’s history of the compilation, interpretation, and communication of long-term volcano monitoring and eruption data (for instance, seismic, geodetic, and petrologic-geochemical data and detailed eruption chronologies) is perhaps unparalleled in the world community of volcano observatories. The discussion and conclusions drawn in this chapter, which emphasize developments since the 75th anniversary of HVO in 1987, are general and retrospective and are intended to provide context for the more detailed, topically focused chapters of this volume.

VLBI Correlators in Kashima

NASA Technical Reports Server (NTRS)

Sekido, Mamoru; Takefuji, Kazuhiro

2013-01-01

Kashima Space Technology Center (KSTC) is making use of two kinds of software correlators, the multi-channel K5/VSSP software correlator and the fast wide-band correlator 'GICO3,' for geodetic and R&D VLBI experiments. Overview of the activity and future plans are described in this paper.

Timescale dependent deformation of orogenic belts?

NASA Astrophysics Data System (ADS)

Hoth, S.; Friedrich, A. M.; Vietor, T.; Hoffmann-Rothe, A.; Kukowski, N.; Oncken, O.

2004-12-01

The principle aim to link geodetic, paleoseismologic and geologic estimates of fault slip is to extrapolate the respective rates from one timescale to the other to finally predict the recurrence interval of large earthquakes, which threat human habitats. This approach however, is based on two often implicitly made assumptions: a uniform slip distribution through time and space and no changes of the boundary conditions during the time interval of interest. Both assumptions are often hard to verify. A recent study, which analysed an exceptionally complete record of seismic slip for the Wasatch and related faults (Basin and Range province), ranging from 10 yr to 10 Myr suggests that such a link between geodetic and geologic rates might not exist, i.e., that our records of fault displacement may depend on the timescale over which they were measured. This view derives support from results of scaled 2D sandbox experiments, as well as numerical simulations with distinct elements, both of which investigated the effect of boundary conditions such as flexure, mechanic stratigraphy and erosion on the spatio-temporal distribution of deformation within bivergent wedges. We identified three types of processes based on their distinct spatio-temporal distribution of deformation. First, incremental strain and local strain rates are very short-lived are broadly distributed within the bivergent wedge and no temporal pattern could be established. Second, footwall shortcuts and the re-activation of either internal thrusts or of the retro shear-zone are irregularly distributed in time and are thus not predictable either, but last for a longer time interval. Third, the stepwise initiation and propagation of the deformation front is very regular in time, since it depends on the thickness of the incoming layer and on its internal and basal material properties. We consider the propagation of the deformation front as an internal clock of a thrust belt, which is therefore predictable. A deformation front advance cycle requires the longest timescale. Thus, despite known and constant boundary conditions during the simulations, we found only one regular temporal pattern of deformation in a steady active bivergent-wedge. We therefore propose that the structural inventory of an orogenic belt is hierarchically ordered with respect to accumulated slip, in analogy to the discharge pattern in a drainage network. The deformation front would have the highest, a branching splay the lowest order. Since kinematic boundary conditions control deformation front advance, its timing and the related maximum magnitude of finite strain, i.e. throw on the frontal thrust are predictable. However, the number of controlling factors, such as the degree of strain softening, the orientation of faults or fluid flow and resulting cementation of faults, responsible for the reactivation of faults increases with increasing distance from the deformation front. Since it is rarely possible to determine the complete network of forces within a wedge, the reactivation of lower order structures is not predictable in time and space. Two implications for field studies may emerge: A change of the propagation of deformation can only be determined, if at least two accretion cycles are sampled. The link between geodetic, paleoseismologic and geologic fault slip estimates can only be successfully derived if the position of the investigated fault within the hierarchical order has not changed over the time interval of interest.

Astro-geodetic platform for high accuracy geoid determinat ion

NASA Astrophysics Data System (ADS)

Bǎdescu, Octavian; Nedelcu, Dan Alin; Cǎlin, Alexandru; Dumitru, Paul Daniel; Cǎlin, Lavinia A.; Popescu, Marcel

The paper presents first technical realizations of a mobile platform for vertical deviation determination at a satisfactory precision and low cost. The conception of the platform was made in the framework of a project regarding CCD astro-geodetic vertical deviation for geoid determination or geoid modeling. The project with the acronym A-GEO represents a collaboration between Technical University of Civil Engineering Bucharest - Faculty of Geodesy, (TUCEB-FG), Astronomical Institute of the Romanian academy (AIRA), and a private partner GeoGIS Proiect S.R.L. The paper presents some hardware and software aspects regarding design, development, and automation of the platform, based on an electro-optical geodetic instrument, CCD observations and satellite time synchronization for astro-geodetic measurements.

Contribution of Apollo lunar photography to the establishment of selenodetic control

NASA Technical Reports Server (NTRS)

Dermanis, A.

1975-01-01

Among the various types of available data relevant to the establishment of geometric control on the moon, the only one covering significant portions of the lunar surface (20%) with sufficient information content, is lunar photography, taken at the proximity of the moon from lunar orbiters. The idea of free geodetic networks is introduced as a tool for the statistical comparison of the geometric aspects of the various data used. Methods were developed for the updating of the statistics of observations and the a priori parameter estimates to obtain statistically consistent solutions by means of the optimum relative weighting concept.

Basic research and data analysis for the earth and ocean physics applications program and for the National Geodetic Satellite program

NASA Technical Reports Server (NTRS)

1975-01-01

Data acquisition using single image and seven image data processing is used to provide a precise and accurate geometric description of the earth's surface. Transformation parameters and network distortions are determined, Sea slope along the continental boundaries of the U.S. and earth rotation are examined, along with close grid geodynamic satellite system. Data are derived for a mathematical description of the earth's gravitational field; time variations are determined for geometry of the ocean surface, the solid earth, gravity field, and other geophysical parameters.

Real-Time In-Situ Measurements for Earthquake Early Warning and Space-Borne Deformation Measurement Mission Support

NASA Astrophysics Data System (ADS)

Kedar, S.; Bock, Y.; Webb, F.; Clayton, R. W.; Owen, S. E.; Moore, A. W.; Yu, E.; Dong, D.; Fang, P.; Jamason, P.; Squibb, M. B.; Crowell, B. W.

2010-12-01

In situ geodetic networks for observing crustal motion have proliferated over the last two decades and are now recognized as indispensable tools in geophysical research, along side more traditional seismic networks. The 2007 National Research Council’s Decadal Survey recognizes that space-borne and in situ observations, such as Interferometric Synthetic Aperture Radar (InSAR) and ground-based continuous GPS (CGPS) are complementary in forecasting, in assessing, and in mitigating natural hazards. However, the information content and timeliness of in situ geodetic observations have not been fully exploited, particularly at higher frequencies than traditional daily CGPS position time series. Nor have scientists taken full advantage of the complementary natures of geodetic and seismic data, as well as those of space-based and in situ observations. To address these deficits we are developing real-time CGPS data products for earthquake early warning and for space-borne deformation measurement mission support. Our primary mission objective is in situ verification and validation for DESDynI, but our work is also applicable to other international missions (Sentinel 1a/1b, SAOCOM, ALOS 2). Our project is developing new capabilities to continuously observe and mitigate earthquake-related hazards (direct seismic damage, tsunamis, landslides, volcanoes) in near real-time with high spatial-temporal resolution, to improve the planning and accuracy of space-borne observations. We also are using GPS estimates of tropospheric zenith delay combined with water vapor data from weather models to generate tropospheric calibration maps for mitigating the largest source of error, atmospheric artifacts, in InSAR interferograms. These functions will be fully integrated into a Geophysical Resource Web Services and interactive GPS Explorer data portal environment being developed as part of an ongoing MEaSUREs project and NASA’s contribution to the EarthScope project. GPS Explorer, originally designed for web-based dissemination of long-term Solid Earth Science Data Records (ESDR’s) such as deformation time series, tectonic velocity vectors, and strain maps, provides the framework for seamless inclusion of the high rate data products. Detection and preliminary modeling of interesting signals by dense real-time high-rate ground networks will allow mission planners and decision makers to fully exploit the less-frequent but higher resolution InSAR observations. Fusion of in situ elements into an advanced observation system will significantly improve the scientific value of extensive surface displacement data, provide scientists with improved access to modern software tools to manipulate and model these data, increase the data’s accuracy and timeliness at higher frequencies than available from space-based observations, and increase the accuracy of space-based observations through calibration of atmospheric and other systematic errors.

QuakeSim Project Networking

NASA Astrophysics Data System (ADS)

Kong, D.; Donnellan, A.; Pierce, M. E.

2012-12-01

QuakeSim is an online computational framework focused on using remotely sensed geodetic imaging data to model and understand earthquakes. With the rise in online social networking over the last decade, many tools and concepts have been developed that are useful to research groups. In particular, QuakeSim is interested in the ability for researchers to post, share, and annotate files generated by modeling tools in order to facilitate collaboration. To accomplish this, features were added to the preexisting QuakeSim site that include single sign-on, automated saving of output from modeling tools, and a personal user space to manage sharing permissions on these saved files. These features implement OpenID and Lightweight Data Access Protocol (LDAP) technologies to manage files across several different servers, including a web server running Drupal and other servers hosting the computational tools themselves.

Mechanics of distributed fault and block rotation

NASA Technical Reports Server (NTRS)

Nur, A.; Scotti, O.; Ron, H.

1989-01-01

Paleomagnetic data, structural geology, and rock mechanics are used to explore the validity and significance of the block rotation concept. The analysis is based on data from Northern Israel, where fault slip and spacing are used to predict block rotation; the Mojave Desert, with well documented strike-slip sets; the Lake Mead, Nevada fault system with well-defined sets of strike-slip faults; and the San Gabriel Mountains domain with a multiple set of strike-slip faults. The results of the analysis indicate that block rotations can have a profound influence on the interpretation of geodetic measurments and the inversion of geodetic data. Furthermore, the block rotations and domain boundaries may be involved in creating the heterogeneities along active fault systems which may be responsible for the initiation and termination of earthquake rupture.

Current status of the EPOS WG4 - GNSS and Other Geodetic Data

NASA Astrophysics Data System (ADS)

Fernandes, Rui; Bastos, Luísa; Bruyninx, Carine; D'Agostino, Nicola; Dousa, Jan; Ganas, Athanassios; Lidberg, Martin; Nocquet, Jean-Mathieu

2013-04-01

WG4 - "EPOS Geodetic Data and Other Geodetic Data" is the Working Group of the EPOS project in charge of defining and preparing the integration of the existing Pan-European Geodetic Infrastructures that will support the European Geosciences, which is the ultimate goal of the EPOS project. The WG4 is formed by representatives of the participating EPOS countries (23) but it is also open to the entire geodetic community. In fact, WG4 also includes members from countries that formally are not part of the current phase of EPOS. In an ongoing effort, the majority of existing GNSS Research Infrastructures in Europe were identified. The current database, available at http://epos-couch.cloudant.com/epos-couch/_design/epos-couch/, lists a total of 50 Research Infrastructures managing a total of 1534 GNSS CORS sites. This presentation intends to detail the work being produced within the working group WG4 related with the definition of strategies towards the implementation of the best solutions that will permit to the end-users, and in particular geo-scientists, to access the geodetic data, derived solutions, and associated metadata using transparent and uniform processes. The first step toward the design of an implementation and business plan is the definition of the core services for geodetic data within EPOS. In this talk, we will present the current status of the discussion about the content of core services. Three levels of core services could be distinguished, for which their content need to be defined. The 3 levels are: (1) the core services associated to data (diffusion, archive, long-term preservation, quality check, rapid analysis) (2) core services associated to geodetic products (analysis, products definition like position time series, velocity field and Zenithal Total Delay) (3) User oriented services (reference frames, real-time solutions for early warning systems, strain rate maps, meteorology, space weather, …). Current propositions and remaining open questions will be discussed.

Large geodetic time series constraining the spatial distribution and the time evolution of the velocity field at the western tip of the Aden Ridge in Afar

NASA Astrophysics Data System (ADS)

Doubre, C.; Deprez, A.; Masson, F.; Socquet, A.; Ulrich, P.; Ibrahim Ahmed, S.; de Chabalier, J. B.; Ahmadine Omar, A.; Vigny, C.; Ruegg, J. C.

2014-12-01

We present the results of the last GPS campaign conducted over the Djiboutian part of Eastern Afar. A large and dense geodetic network has been measured regularly since the 90's, and allows an accurate determination of the velocity field associated with the western tip of the Arabia-Somalia divergent plate boundary. Within the Tadjoura Gulf, the Aden ridge consists of a series of 3 en échelon, submerged spreading segments, except for the Asal segment, which is partly above water. The repetition of 6 to 7 measurements together with 6 permanent continuous GNSS stations allow an opportunity to study the spatial distribution of the active extension in relation to these 3 segments, but also to study time variations of the displacements, which are greatly expected to be transitory because of the occurrence of dyking events, small to intermediate seismic events, and volcanic activity. The divergent motion of the two margins of the Gulf occurs at ~15 mm/yr, which is consistent with the long-term estimates of the Arabia-Somalia motion. Across the Asal segment, this value confirms that the effect of the dyking event in 1978 has ended. The velocity gradients show that the deformation is distributed from the southern to the northern rift shoulder. As revealed by the InSAR data however, the along-axis variations of the deformation pattern, i.e. clear superficial active faults in the SE part of the rift and deep opening in the NW part, suggests the remaining influence of the previous dyke intrusions within the segment inner floor. The time series show that the velocity field was more heterogeneous before 2003, when the micro-seismic activity was significant, particularly around the volcanic center. The striking feature of the time evolution of the velocity field consists in the transition from an extension mainly localized across the Asal segment before 2003 to an extension more distributed, implying the influence of the southern Quaternary structures forming the Gaggade and Hanle Basins. This results in a decrease of the opening velocity across the Asal segment. This crucial change suggests that the activity of the volcanic/geothermal centre in the segment is a determining factor in the spatial organization of the deformation, by affecting the activity of the normal faults and thereby favoring the concentration of the extensive deformation.

5 CFR 831.301 - Military service.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Administration (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed... (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed before the...

5 CFR 831.301 - Military service.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Administration (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed... (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed before the...

5 CFR 831.301 - Military service.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Administration (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed... (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed before the...

5 CFR 831.301 - Military service.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Administration (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed... (formerly Coast and Geodetic Survey and Environmental Science Services Administration), performed before the...

Success! Detailed Pre-event Analysis Identified the Slip Area and Magnitude of the Sept. 2012 MW 7.6 Nicoya Earthquake

NASA Astrophysics Data System (ADS)

Newman, A. V.; Protti, M.; Gonzalez, V. M.; Dixon, T. H.; Schwartz, S. Y.; Feng, L.; Peng, Z.; Marshall, J.; Malservisi, R.; Owen, S. E.

2013-05-01

On September 5th, 2012 a moment magnitude (MW) 7.6 earthquake struck the seismogenic megathrust of Nicoya Costa Rica. Though, we knew not precisely when, this event was not unexpected, and occurred after the development of substantial pre-event scientific discovery and earthquake infrastructural development. Beginning in the late- 1990's Nicoya Costa Rica was recognized by the U.S. National Science Foundation -MARGINS program as a focus area for seismogenic zone studies in part because of the unique proximity of land to the active subduction megathrust. The region also has very fast convergence (~9 cm/a) and has suffered from regular M7+ earthquakes in 1853, 1900 and 1950. Another similar event was expected by many. Pre-event analysis identified the structure of the subduction interface [Newman et al., GRL, 2002; DeShon et al., GJI, 2006], the location and rate changes of ongoing microseismicity [Newman et al., GRL, 2002, Ghosh et al.,GRL, 2008], the location and degree of locking that developed during the late interseismic [Norabuena et al., JGR, 2006; Feng et al., JGR, 2012], and its relation to ongoing low-frequency earthquakes, subduction tremor, and episodic slip events [Walter et al., GRL, 2011; Outerbridge et al., JGR, 2010, Jiang et al., G3, 2012]. Feng et al., [2012] using campaign and continuous GPS data through 2012, identified complex locked 50x50 km patch along the central coast of Nicoya, the locale that failed in Sept 2012, and concluded that the region had the potential to fail in an MW 7.8 event should the most recent locking be representative of behavior since the last major event in 1950. In operation at the time of the event was a substantial NSF-funded continuous GPS (17 station) and seismic (18 station) network maintained by USF, UCSC, and GIT, in cooperation with OVSICORI. The seismic network captured the initial motions of the mainshock before clipping, as well as pre-shock and aftershock activity [Walter et al., (this meeting), 2013]. The continuous GPS network captured the coseismic offset, and evolution of rupture and postseismic relaxation through high-rate and daily processing [Malservisi et al., Lay et al., (this meeting), 2013]. Immediately after the event, an aggressive campaign was performed to fix problems with continuously operating seismic and GPS sites, reoccupy all survey GPS sites occupied last in 2010 and reported in Feng et al., [2012], and perform a rapid coastal deformation and erosional survey [Marshall et al., (this meeting), 2013]. Here we will also detail the results of the coseismic displacement as observed by geodetic and geomorphic methods and compare the spatial distribution relative to the most recent published locking results as derived by both seismic proxy [Ghosh et al., 2008] and geodetic means [Feng et al., 2012], and discuss the implications of such detailed observations for understanding overall subduction earthquake potential.

Seafloor spreading event in western Gulf of Aden during the November 2010-March 2011 period captured by regional seismic networks: evidence for diking events and interactions with a nascent transform zone

NASA Astrophysics Data System (ADS)

Ahmed, Abdulhakim; Doubre, Cécile; Leroy, Sylvie; Kassim, Mohamed; Keir, Derek; Abayazid, Ahmadine; Julie, Perrot; Laurence, Audin; Vergne, Jérome; Alexandre, Nercessian; Jacques, Eric; Khanbari, Khaled; Sholan, Jamal; Rolandone, Frédérique; Al-Ganad, Ismael

2016-05-01

In November 2010, intense seismic activity including 29 events with a magnitude above 5.0, started in the western part of the Gulf of Aden, where the structure of the oceanic spreading ridge is characterized by a series of N115°-trending slow-spreading segments set within an EW-trending rift. Using signals recorded by permanent and temporary networks in Djibouti and Yemen, we located 1122 earthquakes, with a magnitude ranging from 2.1 to 5.6 from 2010 November 1 to 2011 March 31. By looking in detail at the space-time distribution of the overall seismicity, and both the frequency and the moment tensor of large earthquakes, we re-examine the chronology of this episode. In addition, we also interpret the origin of the activity using high-resolution bathymetric data, as well as from observations of seafloor cable damage caused by high temperatures and lava flows. The analysis allows us to identify distinct active areas. First, we interpret that this episode is mainly related to a diking event along a specific ridge segment, located at E044°. In light of previous diking episodes in nearby subaerial rift segments, for which field constraints and both seismic and geodetic data exist, we interpret the space-time evolution of the seismicity of the first few days. Migration of earthquakes suggests initial magma ascent below the segment centre. This is followed by a southeastward dike propagation below the rift immediately followed by a northwestward dike propagation below the rift ending below the northern ridge wall. The cumulative seismic moment associated with this sequence reaches 9.1 × 1017 Nm, and taking into account a very low seismic versus geodetic moment, we estimate a horizontal opening of ˜0.58-2.9 m. The seismic activity that followed occurred through several bursts of earthquakes aligned along the segment axis, which are interpreted as short dike intrusions implying fast replenishment of the crustal magma reservoir feeding the dikes. Over the whole period, the opening is estimated to be ˜1.76-8.8 m across the segment. A striking feature of this episode is that the seismicity remained confined within one individual segment, whereas the adjacent en-echelon segments were totally quiescent, suggesting that the magma supply system of one segment is disconnected from those of the neighbouring segments. Second, we identify activity induced by the first intrusion with epicentres aligned along an N035°E-trending, ˜30 km long at the northwestern end of the active opening segment. This group encompasses more than seven earthquakes with magnitude larger than 5.0, and with strike-slip focal mechanisms consistent with the faults identified in the bathymetry and the structural pattern of the area. We propose that a transform fault is currently in formation which indicates an early stage of the ridge segmentation, at the locus of the trend change of the spreading ridge, which also corresponds to the boundary between a clear oceanic lithosphere and the zone of transform between continental and oceanic crust.

Development of GPS/A Seafloor Geodetic Network Along Japan Trench and Onset of Its Operation

NASA Astrophysics Data System (ADS)

Kido, M.; Fujimoto, H.; Osada, Y.; Ohta, Y.; Yamamoto, J.; Tadokoro, K.; Okuda, T.; Watanabe, T.; Nagai, S.; Kenji, Y.

2012-12-01

The Tohoku-oki earthquake in 2011 revealed that an M9-class giant earthquake could occur even in the old subduction zone and that coseismic slip can reach its frontal wedge, where we considered no significant stress had been accumulated in. One of the leading figure of such finding is in situ seafloor geodetic measurement, such as GPS/A technique for horizontal displacement and pressure gauge for vertical displacement. Japan Coast Guard and Japanese university group had developed several GPS/A sites near the source region of the Tohoku-oki earthquake and detected quite large coseismic movements over 20 m in there. Displacement vectors observed these sites showed systematic variation, i.e., mainly confined in the off-Miyagi area and getting larger near the trench. However, subsequent post-seismic deformation shows inexplicable distribution. In order to elucidate this complex feature, MEXT Japan has decided to construct dense and widely-extended GPS/A network along Japan trench, including deep area (~6000m). We, Tohoku and Nagoya universities, have firstly developed high-powered seafloor transponders with an omnidirectional acoustic unit that works at 6000 m deep ocean and enable acoustic ranging over 13 km slant length. In addition, using high-energy density battery, its lifetime is expected 10 years with normal operation. Secondly, we examined the optimal distribution of GPS/A sites forming a network, taken pre-existing sites into consideration. The new network consists of 20 sites (roughly four transponders at a single site and 86 transponders in total). The distribution is dense near the area of complex post-seismic deformation and extended over 400 km to cover the adjacent area of the source region, in where induced earthquake may be expected. The largest obstacle to draw network plan is seafloor topography. Because a GPS/A site is a seafloor benchmark, its installation must be on flat and locally stable spot. Since a single GPS/A site consists of three or more transponders in an area extending roughly the same dimension of its depth, flat spot is quite limited especially near the trench. The positions of the 20 sites were carefully determined using a high-definition bathymetry map. We already have constructed two sites, one of which is 5500 m depth, and successfully obtained acoustic data. In September, we will install rest of the sites (18 sites) and begin initial campaign survey. The second campaign is planned in November. We will introduce details of the network and report updated result in the talk.

GPS Measurements for Detecting Aseismic Creeping in the Ismetpasa Region of North Anatolian Fault Zone, Turkey

NASA Astrophysics Data System (ADS)

Ozener, H.; Dogru, A.; Turgut, B.; Yilmaz, O.; Halicioglu, K.; Sabuncu, A.

2010-12-01

In 1972, a six point-network was established by General Directorate of Mapping in Gerede-Ismetpasa. This region is relatively quiet segment of western NAF which is creeping along steadily. This network was surveyed by terrestrial techniques in 1972 and 1973. The Ismetpasa Network was re-measured in 1982 and in 1992 by the Geodesy Working Group of Istanbul Technical University. Although the same network (with five points) was observed in 2002 and 2007 by Zonguldak Karaelmas University applying GPS technique, with 1-hour site occupation, the characteristics of movement has not been detected implicitly. This type of movement still raises a question about the accumulation of tectonic movements in the region. Geodesy Department of Kandilli Observatory and Earthquake Research Institute (KOERI) of Bogazici University has been re-surveyed the network by campaign-based static GPS surveying (10-hour site occupation) since 2005. The GPS velocities data coming from geodynamic GPS networks of the crustal deformation studies and the analysis of repeated geodetic observations give us significant information about the elastic deformation. Therefore, data gathered in this study is processed using GAMIT/GLOBK software and analyzed together with previously collected data to obtain velocity field and strain accumulation in the study area.

Comparisons of seismic and geodetic strain across the East African rift: Implications for magmatism during rifting

NASA Astrophysics Data System (ADS)

Lindsey, N.; Ebinger, C. J.; Pritchard, M. E.; Cote, D. M.

2010-12-01

Knowledge of how the continental lithosphere accommodates strain in an active rift setting is essential to both earthquake and volcanic hazard analyses. Far-field and impinging mantle plumes drive extension within the fault-bounded rift systems of East Africa. Our study aims to evaluate models of distributed strain and localized strain between multiple rigid plates using earthquake catalogs and existing constraints, including high resolution DEMs that reveal the spatial distribution of young faults across the broad uplifts of eastern and southern Africa. We determine cumulative seismic moment release within 0.5 degree bins across the Afro-Arabian rift system using the entire NEIC earthquake catalog (1973-present), and compare these results to geodetic estimates of strain and extensional velocity. The small bin size permits comparison of strain with geological factors, including geological terrain, border fault distribution, and the presence or absence of volcanism. Our results highlight the significance of magmatism in strain accommodation across the rift system, and suggest that some strain and magmatism occur within ‘rigid blocks’, such as the Tanzania craton. Throughout the Afro-Arabian rift system, seismic moment release lags geodetic moment release by a factor of 2, consistent with aseismic creep deformation. However, our comparisons indicate that aseismic deformation accounts for a much higher percent of geodetic moment release: approximately 90% in the Main Ethiopian and Eastern rifts, and >97% in the Afar rift zone where incipient seafloor spreading occurs. The time-averaged strain distributions match the estimates from intense seismo-volcanic rifting episodes in Afar, indicating the data base is representative of longer-term patterns in Afar. We see no systematic variation in interbasinal accommodation zones or rift segment offsets, arguing against the development of transform-like structures prior to plate rupture.

A new velocity field for Africa from combined GPS and DORIS space geodetic Solutions: Contribution to the definition of the African reference frame (AFREF)

NASA Astrophysics Data System (ADS)

Saria, E.; Calais, E.; Altamimi, Z.; Willis, P.; Farah, H.

2013-04-01

We analyzed 16 years of GPS and 17 years of Doppler orbitography and radiopositioning integrated by satellite (DORIS) data at continuously operating geodetic sites in Africa and surroundings to describe the present-day kinematics of the Nubian and Somalian plates and constrain relative motions across the East African Rift. The resulting velocity field describes horizontal and vertical motion at 133 GPS sites and 9 DORIS sites. Horizontal velocities at sites located on stable Nubia fit a single plate model with a weighted root mean square residual of 0.6 mm/yr (maximum residual 1 mm/yr), an upper bound for plate-wide motions and for regional-scale deformation in the seismically active southern Africa and Cameroon volcanic line. We confirm significant southward motion ( ˜ 1.5 mm/yr) in Morocco with respect to Nubia, consistent with earlier findings. We propose an updated angular velocity for the divergence between Nubia and Somalia, which provides the kinematic boundary conditions to rifting in East Africa. We update a plate motion model for the East African Rift and revise the counterclockwise rotation of the Victoria plate and clockwise rotation of the Rovuma plate with respect to Nubia. Vertical velocities range from - 2 to +2 mm/yr, close to their uncertainties, with no clear geographic pattern. This study provides the first continent-wide position/velocity solution for Africa, expressed in International Terrestrial Reference Frame (ITRF2008), a contribution to the upcoming African Reference Frame (AFREF). Except for a few regions, the African continent remains largely under-sampled by continuous space geodetic data. Efforts are needed to augment the geodetic infrastructure and openly share existing data sets so that the objectives of AFREF can be fully reached.

Societal challenges-oriented data-rich undergraduate teaching resources for geoscience classrooms and field courses

NASA Astrophysics Data System (ADS)

Pratt-Sitaula, B. A.; Walker, B.; Douglas, B. J.; Crosby, B. T.; Charlevoix, D. J.; Crosby, C. J.; Shervais, K.

2016-12-01

The NSF-funded GEodesy Tools for Societal Issues (GETSI) project is developing modules for use in introductory and majors-level courses that emphasize a broad range of geodetic data and quantitative skills applied to societally important issues of climate change, natural hazards, and water resources (serc.carleton.edu/getsi). The modules fill gaps in existing undergraduate curricula, which seldom include geodetic methods. Published modules are "Ice mass and sea level changes", "Imaging active tectonics with LiDAR and InSAR", "Measuring water resources with GPS, gravity, and traditional methods", "Surface process hazards", and "GPS, strain, and earthquakes". The GETSI Field Collection features geodetic field techniques. The field-oriented module "Analyzing high resolution topography with terrestrial laser scanning (TLS) and structure from motion (SfM)" is already published and "High precision positioning with static and kinematic GPS" will be published in 2017. Modules are 1-3 weeks long and include student exercises, data analysis, and extensive supporting materials. For field modules, prepared data sets are provided for courses that cannot collect field data directly. All modules were designed and developed by teams of faculty and content experts and underwent rigorous review and classroom testing. Collaborating institutions are UNAVCO (which runs NSF's Geodetic Facility), Indiana University, Mt San Antonio College, and Idaho State University. Science Education Resource Center (SERC) is providing assessment and evaluation expertise. If future funding is successful, the topic range will be expanded (e.g., volcanic hazards, more water resources, and ecological applications of geodesy). Funding to date has been provided by NSF's TUES (Transforming Undergraduate Education in STEM) and IUSE (Improving Undergraduate STEM Education).

A global tectonic activity map with orbital photographic supplement

NASA Technical Reports Server (NTRS)

Lowman, P. D., Jr.

1981-01-01

A three part map showing equatorial and polar regions was compiled showing tectonic and volcanic activity of the past one million years, including the present. Features shown include actively spreading ridges, spreading rates, major active faults, subduction zones, well defined plates, and volcanic areas active within the past one million years. Activity within this period was inferred from seismicity (instrumental and historic), physiography, and published literature. The tectonic activity map was used for planning global geodetic programs of satellite laser ranging and very long base line interferometry and for geologic education.

38 CFR 3.6 - Duty periods.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Compensation, and Dependency and Indemnity Compensation General § 3.6 Duty periods. (a) Active military, naval... dependency and indemnity compensation. (3) Full-time duty as a commissioned officer of the Coast and Geodetic... dependency and indemnity compensation. (4) Service at any time as a cadet at the United States Military, Air...

38 CFR 3.6 - Duty periods.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Compensation, and Dependency and Indemnity Compensation General § 3.6 Duty periods. (a) Active military, naval... dependency and indemnity compensation. (3) Full-time duty as a commissioned officer of the Coast and Geodetic... dependency and indemnity compensation. (4) Service at any time as a cadet at the United States Military, Air...

38 CFR 3.6 - Duty periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Compensation, and Dependency and Indemnity Compensation General § 3.6 Duty periods. (a) Active military, naval... dependency and indemnity compensation. (3) Full-time duty as a commissioned officer of the Coast and Geodetic... dependency and indemnity compensation. (4) Service at any time as a cadet at the United States Military, Air...

38 CFR 3.6 - Duty periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Compensation, and Dependency and Indemnity Compensation General § 3.6 Duty periods. (a) Active military, naval... dependency and indemnity compensation. (3) Full-time duty as a commissioned officer of the Coast and Geodetic... dependency and indemnity compensation. (4) Service at any time as a cadet at the United States Military, Air...

38 CFR 3.6 - Duty periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Compensation, and Dependency and Indemnity Compensation General § 3.6 Duty periods. (a) Active military, naval... dependency and indemnity compensation. (3) Full-time duty as a commissioned officer of the Coast and Geodetic... dependency and indemnity compensation. (4) Service at any time as a cadet at the United States Military, Air...

Geodetic integration of Sentinel-1A IW data using PSInSAR in Hungary

NASA Astrophysics Data System (ADS)

Farkas, Péter; Hevér, Renáta; Grenerczy, Gyula

2015-04-01

ESA's latest Synthetic Aperture Radar (SAR) mission Sentinel-1 is a huge step forward in SAR interferometry. With its default acquisition mode called the Interferometric Wide Swath Mode (IW) areas through all scales can be mapped with an excellent return time of 12 days (while only the Sentinel-1A is in orbit). Its operational data policy is also a novelty, it allows scientific users free and unlimited access to data. It implements a new type of ScanSAR mode called Terrain Observation with Progressive Scan (TOPS) SAR. It has the same resolution as ScanSAR but with better signal-to-noise ratio distribution. The bigger coverage is achieved by rotation of the antenna in the azimuth direction, therefore it requires very precise co-registration because even errors under a pixel accuracy can introduce azimuth phase variations caused by differences in Doppler-centroids. In our work we will summarize the benefits and the drawbacks of the IW mode. We would like to implement the processing chain of GAMMA Remote Sensing of such data for mapping surface motion with special attention to the co-registration step. Not only traditional InSAR but the advanced method of Persistent Scatterer InSAR (PSInSAR) will be performed and presented as well. PS coverage, along with coherence, is expected to be good due to the small perpendicular and temporal baselines. We would also like to integrate these measurements into national geodetic networks using common reference points. We have installed trihedral corner reflectors at some selected sites to aid precise collocation. Thus, we aim to demonstrate that Sentinel-1 can be effectively used for surface movement detection and monitoring and it can also provide valuable information for the improvement of our networks.

Co-seismic deformation of the August 27, 2012 Mw 7.3 El Salvador and September 5, 2012 Mw 7.6 Costa Rica earthquakes

NASA Astrophysics Data System (ADS)

Geirsson, H.; La Femina, P. C.; DeMets, C.; Mattioli, G. S.; Hernández, D.

2013-05-01

We investigate the co-seismic deformation of two significant earthquakes that occurred along the Middle America trench in 2012. The August 27 Mw 7.3 El Salvador and September 5 Mw 7.6 Nicoya Peninsula, Costa Rica earthquakes, were examined using a combination of episodic and continuous Global Positioning System (GPS) data. USGS finite fault models based on seismic data predict fundamentally different characteristics for the two ruptures. The El Salvador event occurred in a historical seismic gap and on the shallow segment of the Middle America Trench main thrust, rupturing a large area, but with a low magnitude of slip. A small tsunami was observed along the coast in Nicaragua and El Salvador, additionally indicating near-trench rupture. Conversely, the Nicoya, Costa Rica earthquake was predicted to have an order of magnitude higher slip on a spatially smaller patch deeper on the main thrust. We present results from episodic and continuous geodetic GPS measurements made in conjunction with the two earthquakes, including data from newly installed COCONet (Continuously Operating Caribbean GPS Observational Network) sites. Episodic GPS measurements made in El Salvador, Honduras, and Nicaragua following the earthquakes, allow us to estimate the co-seismic deformation field from both earthquakes. Because of the small magnitude of the El Salvador earthquake and its shallow rupture the observed co-seismic deformation is small (<2 cm). Conversely, the Costa Rica earthquake occurred directly beneath a seismic and geodetic network specifically designed to capture such events. The observed displacements exceeded 0.5 m and there is a significant post-seismic transient following the earthquake. We use our estimated co-seismic offsets for both earthquakes to model the magnitude and spatial variability of slip for these two events.

Status and Future Developments of SIRGAS

NASA Astrophysics Data System (ADS)

Fortes, L.; Lauría, E.; Brunini, C.; Amaya, W.; Sanchez, L.; Drewes, H.

2007-05-01

This paper presents the status and future developments of the SIRGAS (Geocentric Reference System for the Americas) project. Since its creation, in 1993, SIRGAS has coordinated two continental GPS campaigns in 1995 an 2000, responsible for the establishment of a very accurate 3D reference frame in the region. First focusing on South America, the project has expanded its scope to Latin America since 2001. Currently the maintenance of the SIRGAS reference frame is carried out through more than 80 continuous operating GNSS (Global Navigation Satellite System) stations available in the region, whose data is officially processed by the International GNSS Service (IGS) Regional Network Associate Analysis Centre for SIRGAS (IGS RNACC-SIR), functioning at the DGFI (Deutsches Geodatisches Forschungsinstitut), in Munich, to generate weekly coordinates and velocity information of each continuous GNSS station. Since October 2006, five additional experimental processing centers - located at the Brazilian Institute of Geography and Statistics (IBGE), National Institute of Statistics, Geography and Informatics of Mexico (INEGI), Military Geographic Institute of Argentina (IGM), University of La Plata (UNLP), Argentina, and Geographic Institute Agustín Codazzi, Colombia (IGAC) - have also been processing data from those stations in order to assume the official processing responsibility in near future. Many Latin American countries have already adopted SIRGAS as their new official reference system. Besides, efforts have been carried out in order to have the national geodetic networks of Central American countries connected to the SIRGAS reference frame, which will be accomplished by a GNSS campaign scheduled for the first semester of 2007. In terms of vertical datum, SIRGAS continues to coordinate with each member country all the necessary efforts towards making the geodetic leveling data available together with gravity information in order to support the computation of geopotential numbers, to be unified in a continental adjustment.

Rupture processes of the 2012 September 5 Mw 7.6 Nicoya, Costa Rica earthquake constrained by improved geodetic and seismological observations

NASA Astrophysics Data System (ADS)

Liu, Chengli; Zheng, Yong; Xiong, Xiong; Wang, Rongjiang; López, Allan; Li, Jun

2015-10-01

On 2012 September 5, the anticipated interplate thrust earthquake ruptured beneath the Nicoya peninsula in northwestern Costa Rica close to the Middle America trench, with a magnitude Mw 7.6. Extensive co-seismic observations were provided by dense near-field strong ground motion, Global Positioning Systems (GPS) networks and teleseismic recordings from global seismic networks. The wealthy data sets available for the 2012 Mw 7.6 Nicoya earthquake provide a unique opportunity to investigate the details of the rupture process of this earthquake. By implementing a non-linear joint inversion with high-rate GPS waveform, more static GPS offsets, strong-motion data and teleseismic body waveform, we obtained a robust and accurate rupture model of the 2012 Mw 7.6 Nicoya earthquake. The earthquake is dominantly a pure thrust component with a maximum slip of 3.5 m, and the main large slip patch is located below the hypocentre, spanning ˜50 km along dip and ˜110 km along strike. The static stress drop is about 3.4 MPa. The total seismic moment of our preferred model is 3.46 × 1020 N m, which gives Mw = 7.6. Due to the fast rupture velocity, most of the seismic moment was released within 70 s. The largest slip patch directly overlaps the interseismic locked region identified by geodetic observations and extends downdip to the intersection with the upper plate Moho. We also find that there is a complementary pattern between the distribution of aftershocks and the co-seismic rupture; most aftershocks locate in the crust of the upper plate and are possibly induced by the stress change caused by the large slip patch.

Marine geodetic control for geoidal profile mapping across the Puerto Rican Trench

NASA Technical Reports Server (NTRS)

Fubara, D. M.; Mourad, A. G.

1975-01-01

A marine geodetic control was established for the northern end of the geoidal profile mapping experiment across the Puerto Rican Trench by determining the three-dimensional geodetic coordinates of the four ocean-bottom mounted acoustic transponders. The data reduction techniques employed and analytical processes involved are described. Before applying the analytical techniques to the field data, they were tested with simulated data and proven to be effective in theory as well as in practice.

Global Geodesy Using GPS Without Fiducial Sites

NASA Technical Reports Server (NTRS)

Heflin, Michael B.; Blewitt, Geoffrey

1994-01-01

Global Positioning System, GPS, used to make global geodetic measurements without use of fiducial site coordinates. Baseline lengths and geocentric radii for each site determined without having to fix any site coordinates. Given n globally distributed sites, n baseline lengths and n geocentric radii form polyhedron with each site at vertex and with geocenter at intersection of all radii. Geodetic information derived from structure of polyhedron and its change with time. Approach applied to any global geodetic technique.

Seafloor Geodesy usi­ng Wave Gliders to study Earthquake and Tsunami Hazards at Subduction Zones

NASA Astrophysics Data System (ADS)

Sathiakumar, S.; Barbot, S.; Hill, E.; Peng, D.; Zerucha, J.; Suhaimee, S.; Chia, G.; Salamena, G. G.; Syahailatua, A.

2016-12-01

Land-based GNSS networks are now in place to monitor most subduction zones of the world. These provide valuable information about the amount of­ geodetic strain accumulated in the region, which in turn gives insight into the seismic potential. However, it is usually impossible to resolve activity on the megathrust near the trench using land-based GNSS data alone, given typical signal-to-noise ratios. Ship-based seafloor geodesy is being used today to fill this observation gap. However, surveys using ships are very expensive, tedious and impractical due to the large areas to be covered. Instead of discrete missions using ships, continuous monitoring of the seafloor using autonomous marine robots would aid in understanding the tectonic setting of the seafloor better at a potentially lower cost, as well as help in designing better warning systems. Thus, we are developing seafloor geodesy capabilities using Wave Gliders, a new class of wave-propelled, persistent marine autonomous vehicle using a combination of acoustic and GNSS technologies. We use GNSS/INS to position the platform, and acoustic ranging to locate the seafloor. The GNSS/INS system to be integrated with the Wave Gliders has stringent requirements of low power, light weight, and high accuracy. All these factors are equally important due to limited power and space in the Wave Gliders and the need for highly accurate and precise measurements. With this hardware setup, a limiting factor is the accuracy of measurement of the sound velocity in the water column. We plan to obtain precise positioning of seafloor by exploring a measurement setup that minimizes uncertainties in sound velocity. This will be achieved by making fine-resolution measurements of the two-way travel time of the acoustic waves underwater using the Wave Gliders, and performing statistical signal processing on this data to obtain more reliable sound velocity measurement. This enhanced seafloor geodetic technique using Wave Gliders should enable us to measure deformation of the seafloor over annual and decadal time scales. Combination of seafloor data with land based GPS networks would allow us to study processes from the deep-ocean trench to the coast in a better way, and thereby give a more complete picture of the subduction process.

A Gravimetric Geoid Model for Vertical Datum in Canada

NASA Astrophysics Data System (ADS)

Veronneau, M.; Huang, J.

2004-05-01

The need to realize a new vertical datum for Canada dates back to 1976 when a study group at Geodetic Survey Division (GSD) investigated problems related to the existing vertical system (CGVD28) and recommended a redefinition of the vertical datum. The US National Geodetic Survey and GSD cooperated in the development of a new North American Vertical Datum (NAVD88). Although the USA adopted NAVD88 in 1993 as its datum, Canada declined to do so as a result of unexplained discrepancies of about 1.5 m from east to west coasts (likely due to systematic errors). The high cost of maintaining the vertical datum by the traditional spirit leveling technique coupled with budgetary constraints has forced GSD to modify its approach. A new attempt (project) to modernize the vertical datum is currently in process in Canada. The advance in space-based technologies (e.g. GPS, satellite radar altimetry, satellite gravimetry) and new developments in geoid modeling offer an alternative to spirit leveling. GSD is planning to implement, after stakeholder consultations, a geoid model as the new vertical datum for Canada, which will allow space-based technology users access to an accurate and uniform datum all across the Canadian landmass and surrounding oceans. CGVD28 is only accessible through a limited number of benchmarks, primarily located in southern Canada. The new vertical datum would be less sensitive to geodynamic activities (post-glacial rebound and earthquake), local uplift and subsidence, and deterioration of the benchmarks. The adoption of a geoid model as a vertical datum does not mean that GSD is neglecting the current benchmarks. New heights will be given to the benchmarks by a new adjustment of the leveling observations, which will be constrained to the geoid model at selected stations of the Active Control System (ACS) and Canadian Base Network (CBN). This adjustment will not correct vertical motion at benchmarks, which has occurred since the last leveling observations. The presentation provides an overview of the "Height Modernization" project, and discusses the accuracy of the existing geoid models in Canada.

Estimating network effect in geocenter motion: Applications

NASA Astrophysics Data System (ADS)

Zannat, Umma Jamila; Tregoning, Paul

2017-10-01

The network effect is the error associated with the subsampling of the Earth surface by space geodetic networks. It is an obstacle toward the precise measurement of geocenter motion, that is, the relative motion between the center of mass of the Earth system and the center of figure of the Earth surface. In a complementary paper, we proposed a theoretical approach to estimate the magnitude of this effect from the displacement fields predicted by geophysical models. Here we evaluate the effectiveness of our estimate for two illustrative physical processes: coseismic displacements inducing instantaneous changes in the Helmert parameters and elastic deformation due to surface water movements causing secular drifts in those parameters. For the first, we consider simplified models of the 2004 Sumatra-Andaman and the 2011 Tōhoku-Oki earthquakes, and for the second, we use the observations of the Gravity Recovery and Climate Experiment, complemented by an ocean model. In both case studies, it is found that the magnitude of the network effect, even for a large global network, is often as large as the magnitude of the changes in the Helmert parameters themselves. However, we also show that our proposed modification to the definition of the center of network frame to include weights proportional to the area of the Earth surface that the stations represent can significantly reduce the network effect in most cases.

The MAFI Project: Mapping Active Faults in Italy by Using Microseismicity Data.

NASA Astrophysics Data System (ADS)

Chiarabba, C.; Amato, A.; Augliera, P.; Bagh, S.; Cattaneo, M.; Chiaraluce, L.; de Gori, P.; di Bartolomeo, P.; Govoni, A.; Michelini, A.; Moretti, M.; Piccinini, D.; Romanelli, M.

2004-12-01

In past years, earthquake forecasting and seismic hazard in Italy have been approached by using geological and geophysical data yielding only a partial definition of seismic release for the main active structures. In this project, we collect seismological and geodetic data to yield deterministic constraints for seismic hazard studies in areas where large earthquakes are expected to occur in a near future, called lacunae. The basic idea is to massively deploy arrays of instruments in the lacunae areas to acquire seismic and geodetic data with the goals of defining location, geometry and kinematics of the active faults and possibly constraining their strain rate. We selected three target regions: two along the Apennines (Northern Umbria and Abruzzo) and one in the Southern Alps (Alpago-Cansiglio). These areas are characterized by different tectonics and different historical seismic release. We present results for the areas located along the Apennines: the Umbria 2000-2001 and the Abruzzo 2003-2004 experiments while for the Alpago-Cansiglio we are still collecting and processing data. Preliminary results for the Umbria lacuna shows that the collected microearthquakes allow us to clearly recognize the fault system geometry and the deep structure (P- and S-wave velocity and attenuation).

International Laser Ranging Service (ILRS) 2003-2004 Annual Report

NASA Technical Reports Server (NTRS)

Pearlman, Michael (Editor); Noll, Carey (Editor)

2005-01-01

The International Laser Ranging Service (ILRS) organizes and coordinates Satellite Laser Ranging (SLR) and Lunar Laser Ranging (LLR) to support programs in geodetic, geophysical, and lunar research activities and provides the International Earth Rotation and Reference Systems Service (IERS) with products important to the maintenance of an accurate International Terrestrial Reference Frame (ITRF). This reference frame provides the stability through which systematic measurements of the Earth can be made over thousands of kilometers, decades of time, and evolution of measurement technology. This 2003-2004 ILRS annual report is comprised of individual contributions from ILRS components within the international geodetic community for the years 2003-2004. The report documents changes and progress of the ILRS and is also available on the ILRS Web site at http://ilrs.gsfc.nasa.gov/reports/ilrs_reports/ilrsar_2003.html.

Status and Plans for the Vienna VLBI and Satellite Software (VieVS 3.0)

NASA Astrophysics Data System (ADS)

Gruber, Jakob; Böhm, Johannes; Böhm, Sigrid; Girdiuk, Anastasiia; Hellerschmied, Andreas; Hofmeister, Armin; Krásná, Hana; Kwak, Younghee; Landskron, Daniel; Madzak, Matthias; Mayer, David; McCallum, Jamie; Plank, Lucia; Schartner, Matthias; Shabala, Stas; Teke, Kamil; Sun, Jing

2017-04-01

The Vienna VLBI and Satellite Software (VieVS) is a geodetic analysis software developed and maintained at Technische Universität Wien (TU Wien) with contributions from groups all over the world. It is used for both academic purposes in university courses as well as for providing Very Long Baseline Interferometry (VLBI) analysis results to the geodetic community. Written in a modular structure in Matlab, VieVS offers easy access to the source code and the possibility to adapt the programs for particular purposes. The new version 3.0, released in early 2017, includes several new features, e.g., improved scheduling capabilities for observing quasars and satellites. This poster gives an overview of all VLBI-related activities in Vienna and provides an outlook to future plans concerning the Vienna VLBI and Satellite Software (VieVS).

The underground seismic array of Gran Sasso (UNDERSEIS), central Italy

NASA Astrophysics Data System (ADS)

Scarpa, R.; Muscente, R.; Tronca, F.; Fischione, C.; Rotella, P.; Abril, M.; Alguacil, G.; Martini, M.; de Cesare, W.

2003-04-01

Since early May, 2002, a small aperture seismic array has been installed in the underground Physics Laboratories of Gran Sasso, located near seismic active faults of central Apennines, Italy. This array is presently composed by 21 three-component short period seismic stations (Mark L4C-3D), with average distance 90 m and semi-circular aperture of 400 m x 600 m. It is intersecting a main seismogenic fault where the presence of slow earthquakes has been recently detected through two wide band geodetic laser interferometers. The underground Laboratories are shielded by a limestone rock layer having 1400 m thickness. Each seismometer is linked, through a 24 bits A/D board, to a set of 6 industrial PC via a serial RS-485 standard. The six PC transmit data to a server through an ethernet network. Time syncronization is provided by a Master Oscillator controlled by an atomic clock. Earthworm package is used for data selection and transmission. High quality data have been recorded since May 2002, including local and regional earthquakes. In particular the 31 October, 2002, Molise (Mw=5.8 earthquake) and its aftershocks have been recorded at this array. Array techniques such as polarisation and frequency-slowness analyses with the MUSIC noise algorithm indicate the high performance of this array, as compared to the national seismic network, for identifying the basic source parameters for earthquakes located at distance of few hundreds of km.

Deep Internal Structure of Mars and the Geophysical Package of Netlander

NASA Technical Reports Server (NTRS)

Lognonne, P.; Giardini, D.; Banerdt, B.; Dehant, V.; Barriot, J. P.; Musmann, G.; Menvielle, M.

2000-01-01

Our present understanding of the interior structure of Mars is mostly based on the interpretation of gravity and rotation data, the chemistry of the SNC (shergottites, nakhlites, chassignites) meteoroids, and a comparison with the much better-known interior structure of the Earth. However geophysical information from previous missions have been insufficient to determine the deep internal structure of the planet. Therefore the state and size of the core and the depth and type of mantle discontinuities are unknown. Most previous seismic experiments have indeed failed, either due to a launch failure (as for the Optimism seismometer onboard the small surface stations of Mars 96) or after failure on Mars (as for the Viking 1 seismometer). The remaining Viking 2 seismometer did not produce a convincing marsquake detection, basically due to too strong wind sensitivity and too low resolution in the teleseismic frequency band. After almost a decade of continuous activity and proposals, the first network mission to Mars, NetLander (NL), is expected to be launched between 2005 and 2007. One of the main scientific objectives of this four-lander network mission will be the determination of the internal structure of the planet using a geophysical package. This package will have a seismometer, a magnetometer, and a geodetic experiment, allowing a complementary approach that will yield many new constraints on the mineralogy and temperature of the mantle and core of the planet.

Integrating Near Fault Observatories (NFO) for EPOS Implementation Phase

NASA Astrophysics Data System (ADS)

Chiaraluce, Lauro

2015-04-01

Following the European Plate Observing System (EPOS) project vision aimed at creating a pan-European infrastructure for Earth sciences to support science for a more sustainable society, we are working on the integration of Near-Fault Observatories (NFOs). NFOs are state of the art research infrastructures consisting of advanced networks of multi-parametric sensors continuously monitoring the chemical and physical processes related to the common underlying earth instabilities governing active faults evolution and the genesis of earthquakes. Such a methodological approach, currently applicable only at the local scale (areas of tens to few hundreds of kilometres), is based on extremely dense networks and less common instruments deserving an extraordinary work on data quality control and multi-parameter data description. These networks in fact usually complement regional seismic and geodetic networks (typically with station spacing of 50-100km) with high-density distributions of seismic, geodetic, geochemical and geophysical sensors located typically within 10-20 km of active faults where large earthquakes are expected in the future. In the initial phase of EPOS-IP, seven NFO nodes will be linked: the Alto Tiberina and Irpinia Observatories in Italy, the Corinth Observatory in Greece, the South-Iceland Seismic Zone, the Valais Observatory in Switzerland, Marmara Sea GEO Supersite in Turkey (EU MARSite) and the Vrancea Observatory in Romania. Our work is aimed at establishing standards and integration within this first core group of NFOs while other NFOs are expected to be installed in the next years adopting the standards established and developed within the EPOS Thematic Core Services (TCS). The goal of our group is to build upon the initial development supported by these few key national observatories coordinated under previous EU projects (NERA and REAKT), inclusive and harmonised TCS supporting the installation over the next decade of tens of near-fault observatories monitoring active faults in different tectonic environments in Europe. We will assist these new NFOs in their design, installation and inclusion in EPOS. These infrastructures will substantially enable advancements in our fundamental understanding of earthquakes generation processes and associated ground shaking due to their high quality near source multidisciplinary data retrieval. While guaranteeing the continuous acquisition and storage of long time-series of such data, we will allow also an easy and direct data discovery and access to the whole community. This implies to strengthen the collaborations with other related EU and global initiatives devoted to the multidisciplinary monitoring and study of active fault zones (such as the GEO Geohazards Supersites initiative). Another key goal is the establishment of a legal governance for such a young community to ensure the long-term sustainability of the services and data access to databases to be used for scientific investigations and accessible via the Integrated Services that will be implemented within the EPOS IP project. The availability of real-time data retrieved by dense and multi-parametric networks located at close distance from the fault provides the unique opportunity of observing all phase of preparation, nucleation and propagation of the earthquake rupture. It is thus of crucial importance to develop methodologies that follow in real-time the evolution of the event. Hence the NFO is the unique and ideal infrastructure for hosting testing centers where a variety of scientific algorithms for real-time monitoring can be operated side-by-side and their performance independently evaluated. Besides the high interest for fundamental science, such developments have obvious societal impact, as they allow precise and timely release of alerts as the seismic event develops, and can attract new stakeholders such as industry partners who are interested in adopting and investing in early warning technologies and evolutionary ground shaking maps. Finally, we will describe how we intend to implement novel tools for visualization and analysis of multidisciplinary data and products to describe the anatomy of active faults and the physical processes governing earthquake generation and faulting. A sort of virtual laboratory aimed at promoting and disseminating Earth sciences at different levels.

Status and Perspective of the IGS Multi-GNSS Experiment (MGEX)

NASA Astrophysics Data System (ADS)

Steigenberger, Peter; Montenbruck, Oliver; Weber, Robert; Hugentobler, Urs

2013-04-01

Following three decades, during which the Global Positioning System GPS has evolved from a military navigation system into an indispensable tool for geodetic research and global monitoring of the Earth, the world of satellite navigation has experienced dramatic changes over the past years. With GLONASS, a second global navigation system has achieved a fully operational status, GPS is introducing modernized civil and encrypted navigation signals, and a variety of new navigation constellations are being built-up in Asia and Europe. These include BeiDou, which has recently opened a regional navigation service in the Asia-Pacific region, Galileo, which now has four satellites in orbit, as well as QZSS, which offers a unique set of signals and service features. In recognition of a rapidly changing GNSS landscape, the International GNSS Service (IGS) has initiated the Multi-GNSS Experiment (MGEX - http://igs.org/mgex) as a platform for early familiarization with emerging navigation systems and to pave the way for a full-featured use thereof in a future multi-GNSS service. As a first step, MGEX has promoted the build-up of a new global network of GNSS monitoring stations, each tracking at least one new constellation (Galileo, BeiDou, or QZSS) on top of GPS, GLONASS and SBAS. By the end of 2012, approximately 50 stations contribute offline and/or real-time data to the MGEX network. To facilitate introduction of new standards (specifically RINEX3 observation and navigation data formats), distinct data archives are used even for those MGEX stations jointly contributing to the legacy IGS. Building-up on the new multi-GNSS network, the generation of associated orbit and clock products has started in the second quarter of 2012. At this stage, only Galileo and QZSS products are offered by selected MGEX Analysis Centers, but the addition of BeiDou is expected in 2013 as the MGEX network expands and new Analysis Centers join the data processing effort. Despite remarkable progress in the first year of the MGEX project, numerous challenges have still to be met before the new constellations can contribute to high-grade navigation and geodetic services. So far, only an immature knowledge of the new navigation satellites and the transmitted signals is available. Much work is left to fully characterize the multitude of inter-signal, inter-frequency and inter-system biases, as well as antenna phase patterns in both the space and user segment. Likewise, proper knowledge of spacecraft attitude control and radiation pressure models appears indispensable for a proper generation of highly-accurate orbit and clock products. Only then will users be able to fully benefit from the high potential of robust, wide-band, and high navigation signals as well as new generations of highly stable clocks offered by the new constellations. Within the presentation, the MGEX project will be introduced and the latest achievements in the network build-up, the product generation and related activities will be presented. Current challenges and necessary steps towards a full-features multi-GNSS service of the IGS will be identified.

Mobile radio interferometric geodetic systems

NASA Technical Reports Server (NTRS)

Macdoran, P. F.; Niell, A. E.; Ong, K. M.; Resch, G. M.; Morabito, D. D.; Claflin, E. S.; Lockhart, T. G.

1978-01-01

Operation of the Astronomical Radio Interferometric Earth Surveying (ARIES) in a proof of concept mode is discussed. Accuracy demonstrations over a short baseline, a 180 km baseline, and a 380 km baseline are documented. Use of ARIES in the Sea Slope Experiment of the National Geodetic Survey to study the apparent differences between oceanographic and geodetic leveling determinations of the sea surface along the Pacific Coast is described. Intergration of the NAVSTAR Global Positioning System and a concept called SERIES (Satellite Emission Radio Interferometric Earth Surveying) is briefly reviewed.

High-precision gravimetric survey in support of lunar laser ranging at Haleakala, Maui, 1976 - 1978

NASA Technical Reports Server (NTRS)

Schenck, B. E.; Laurila, S. H.

1978-01-01

The planning, observations and adjustment of high-precision gravity survey networks established on the islands of Maui and Oahu as part of the geodetic-geophysical program in support of lunar laser ranging at Haleakala, Maui, Hawaii are described. The gravity survey networks include 43 independently measured gravity differences along the gravity calibration line from Kahului Airport to the summit of Mt. Haleakala, together with some key points close to tidal gauges on Maui, and 40 gravity differences within metropolitan Honolulu. The results of the 1976-1978 survey are compared with surveys made in 1961 and in 1964-1965. All final gravity values are given in the system of the international gravity standardization net 1971 (IGSN 71); values are obtained by subtracting 14.57 mgal from the Potsdam value at the gravity base station at the Hickam Air Force Base, Honolulu.

Focus Upon Implementing the GGOS Decadal Vision for Geohazards Monitoring

NASA Astrophysics Data System (ADS)

LaBrecque, John; Stangl, Gunter

2017-04-01

The Global Geodetic Observing System of the IAG identified present and future roles for Geodesy in the development and well being of the global society. The GGOS is focused upon the development of infrastructure, information, analysis, and educational systems to advance the International Global Reference Frame, the International Celestial Reference System, the International Height Reference System, atmospheric dynamics, sea level change and geohazards monitoring. The geohazards initiative is guided by an eleven nation working group initially focused upon the development and integration of regional multi-GNSS networks and analysis systems for earthquake and tsunami early warning. The opportunities and challenges being addressed by the Geohazards working group include regional network design, algorithm development and implementation, communications, funding, and international agreements on data access. This presentation will discuss in further detail these opportunities and challenges for the GGOS focus upon earthquake and tsunami early warning.

Height biases and scale variations in VLBI networks due to antenna gravitational deformations

NASA Astrophysics Data System (ADS)

Abbondanza, Claudio; Sarti, Pierguido; Petrov, Leonid; Negusini, Monia

2010-05-01

The impact of signal path variations (SPVs) caused by antenna gravity deformations on geodetic VLBI results is evaluated for the first time. Elevation-dependent models of SPV for Medicina and Noto (Italy) telescopes were derived from a combination of terrestrial surveying methods to account for gravitational deformations. After applying these models, estimates of the antenna reference point (ARP) positions are shifted upward by 8.9 mm and 6.7 mm, respectively. The impact on other parameters is negligible. To infer the impact of antenna gravity deformations on the entire VLBI network, lacking measurements for other telescopes, we rescaled the SPV models of Medicina and Noto for other antennas according to their size. The effects are changes in VLBI heights in the range [-3,73] mm and a significant net scale increase of 0.3 - 0.8 ppb. This demonstrates the need to include SPV models in routine VLBI data analysis.

The Neural Network In Coordinate Transformation

NASA Astrophysics Data System (ADS)

Urusan, Ahmet Yucel

2011-12-01

In international literature, Coordinate operations is divided into two categories. They are coordinate conversion and coordinate transformation. Coordinates converted from coordinate system A to coordinate system B in the same datum (mean origine, scale and axis directions are same) by coordinate conversion. There are two different datum in coordinate transformation. The basis of each datum to a different coordinate reference system. In Coordinate transformation, coordinates are transformed from coordinate reference system A to coordinate referance system B. Geodetic studies based on physical measurements. Coordinate transformation needs identical points which were measured in each coordinate reference system (A and B). However it is difficult (and need a big reserved budget) to measure in some places like as top of mountain, boundry of countries and seaside. In this study, this sample problem solution was researched. The method of learning which is one of the neural network methods, was used for solution of this problem.

Fortaleza Station Report for 2012

NASA Technical Reports Server (NTRS)

Kaufmann, Pierre; Pereira de Lucena, A. Macilio; Sombra da Silva, Adeildo

2013-01-01

This is a brief report about the activities carried out at the Fortaleza geodetic VLBI station (ROEN: R´adio Observat´orio Espacial do Nordeste), located in Eus´ebio, CE, Brazil, during the period from January until December 2012. The observing activities were resumed in May after the major maintenance that comprised the azimuth bearing replacement. The total observational experiments consisted of 103 VLBI sessions and continuous GPS monitoring recordings.

The Lanzarote Geodynamic Laboratory: new capabilities for monitoring of volcanic activity at Canary Islands

NASA Astrophysics Data System (ADS)

Arnoso, J.; Vélez, E. J.; Soler, V.; Montesinos, F. G.; Benavent, M.

2012-04-01

The volcanic island of Lanzarote is located at the northeastern end of the Canary Islands. Together with Fuerteventura Island, Lanzarote constitutes the emergent part of the East Canary Ridge, which presents a NNE-SSW volcanic alignment. Last eruptive events took place in 1824 and during the period 1730-1736, which is the largest to occur in the archipelago and throw out about 1.3 km3 of volcanic materials. The Lanzarote Geodynamic Laboratory (LGL) was created in 1986 with the idea of making Lanzarote as a natural laboratory to carry out studies in order to acquire more knowledge about its origin, present status and evolution (Vieira et al., 1991; 2006). The LGL has a multidisciplinary scientific purpose and, among others, various objectives are devoted to investigate mass distribution in the Earth system and surface displacements associated to volcanic and/or seismic activity in the island. The influence of LGL is extended throughout the whole geographical area of Lanzarote, including small islands located at the north. The laboratory has 3 observing modules distributed along the island according to its infrastructure and scientific objectives, where more than 70 sensors are recording continuously gravity variations, ground deformations, sea level, seismic activity, meteorological parameters, etc. All these observations are supplemented by periodic measurement of geodetic and geophysical networks that allow us to make studies at local, insular and regional scales. The application of geodetic and geophysical techniques to identify geodynamic signals related to volcanic processes is then a permanent research activity of the laboratory. Nowadays, this fact becomes more interesting due to the ongoing volcanic eruption that is taking place in other island of the Canary Archipelago, El Hierro, since past July 2011. That is, the multidisciplinary research carry on up to now at the LGL allow us to apply multiparameter observations of different kinds of volcanic manifestations at the surface level, and to compare geodynamic processes associated with an active area of the Earth's crust. In turn, the results obtained can provide new inputs for studying precursor of volcanic activity and also contribute to volcanic hazard mitigation. The LGL aims to be a permanent status of renewal, using new technologies for data recording and real time transmission, as well as for testing new sensors, scientific equipment and observational techniques related to monitoring and observation of volcanic activity. All these capabilities are necessary when high-resolution ground based observations must provide us the basis for studying the sources of volcanic deformation. The laboratory is thus open to support and to enhance the collaboration among scientists, as well as national and international institutions involved in research at active volcanic areas.

An algorithmic approach to crustal deformation analysis

NASA Technical Reports Server (NTRS)

Iz, Huseyin Baki

1987-01-01

In recent years the analysis of crustal deformation measurements has become important as a result of current improvements in geodetic methods and an increasing amount of theoretical and observational data provided by several earth sciences. A first-generation data analysis algorithm which combines a priori information with current geodetic measurements was proposed. Relevant methods which can be used in the algorithm were discussed. Prior information is the unifying feature of this algorithm. Some of the problems which may arise through the use of a priori information in the analysis were indicated and preventive measures were demonstrated. The first step in the algorithm is the optimal design of deformation networks. The second step in the algorithm identifies the descriptive model of the deformation field. The final step in the algorithm is the improved estimation of deformation parameters. Although deformation parameters are estimated in the process of model discrimination, they can further be improved by the use of a priori information about them. According to the proposed algorithm this information must first be tested against the estimates calculated using the sample data only. Null-hypothesis testing procedures were developed for this purpose. Six different estimators which employ a priori information were examined. Emphasis was put on the case when the prior information is wrong and analytical expressions for possible improvements under incompatible prior information were derived.

New VLBI2010 scheduling strategies and implications on the terrestrial reference frames.

PubMed

Sun, Jing; Böhm, Johannes; Nilsson, Tobias; Krásná, Hana; Böhm, Sigrid; Schuh, Harald

In connection with the work for the next generation VLBI2010 Global Observing System (VGOS) of the International VLBI Service for Geodesy and Astrometry, a new scheduling package (Vie_Sched) has been developed at the Vienna University of Technology as a part of the Vienna VLBI Software. In addition to the classical station-based approach it is equipped with a new scheduling strategy based on the radio sources to be observed. We introduce different configurations of source-based scheduling options and investigate the implications on present and future VLBI2010 geodetic schedules. By comparison to existing VLBI schedules of the continuous campaign CONT11, we find that the source-based approach with two sources has a performance similar to the station-based approach in terms of number of observations, sky coverage, and geodetic parameters. For an artificial 16 station VLBI2010 network, the source-based approach with four sources provides an improved distribution of source observations on the celestial sphere. Monte Carlo simulations yield slightly better repeatabilities of station coordinates with the source-based approach with two sources or four sources than the classical strategy. The new VLBI scheduling software with its alternative scheduling strategy offers a promising option with respect to applications of the VGOS.

Comparison of hydrological and GRACE-based excitation functions of polar motion in the seasonal spectral band

NASA Astrophysics Data System (ADS)

Nastula, J.; Kolaczek, B.; Salstein, D. A.

2008-04-01

Understanding changes in the global balance of the Earths angular momentum due to the mass redistribution of geophysical fluids is needed to explain the observed polar motion. The impact of continental hydrologic signals, from land water, snow, and ice, on polar motion excitation (hydrological angular momentum-HAM), is still inadequately known. Although estimates of HAM have been made from several models of global hydrology based upon the observed distribution of surface water, snow, and soil moisture, the relatively sparse observation network and the presence of errors in the data and the geophysical fluid models preclude a full understanding of the HAM influence on polar motion variations. Recently the GRACE mission monitoring Earths time variable gravity field has allowed us to determine the mass term of polar motion excitation functions and compare them with the mass term derivable as a residual from the geodetic excitation functions and geophysical fluid motion terms on seasonal time scales. Differences between these mass terms in the years 2004 - 2005.5 are still on the order of 20 mas. Besides the overall mass excitation of polar motion comparisons with GRACE (RL04-release), we also intercompare the non-atmospheric, non-oceanic signals in the mass term of geodetic polar motion excitation with hydrological excitation of polar motion.

New VLBI2010 scheduling strategies and implications on the terrestrial reference frames

NASA Astrophysics Data System (ADS)

Sun, Jing; Böhm, Johannes; Nilsson, Tobias; Krásná, Hana; Böhm, Sigrid; Schuh, Harald

2014-05-01

In connection with the work for the next generation VLBI2010 Global Observing System (VGOS) of the International VLBI Service for Geodesy and Astrometry, a new scheduling package (Vie_Sched) has been developed at the Vienna University of Technology as a part of the Vienna VLBI Software. In addition to the classical station-based approach it is equipped with a new scheduling strategy based on the radio sources to be observed. We introduce different configurations of source-based scheduling options and investigate the implications on present and future VLBI2010 geodetic schedules. By comparison to existing VLBI schedules of the continuous campaign CONT11, we find that the source-based approach with two sources has a performance similar to the station-based approach in terms of number of observations, sky coverage, and geodetic parameters. For an artificial 16 station VLBI2010 network, the source-based approach with four sources provides an improved distribution of source observations on the celestial sphere. Monte Carlo simulations yield slightly better repeatabilities of station coordinates with the source-based approach with two sources or four sources than the classical strategy. The new VLBI scheduling software with its alternative scheduling strategy offers a promising option with respect to applications of the VGOS.

Coexisting shortening and extension along the "Africa-Eurasia" plate boundary in southern Italy

NASA Astrophysics Data System (ADS)

Cuffaro, M.; Riguzzi, F.; Scrocca, D.; Doglioni, C.

2009-04-01

We performed geodetic strain rate field analyses along the "Africa (Sicily microplate)"-"Eurasia (Tyrrhenian microplate)" plate boundary in Sicily (southern Italy), using new GPS velocities from a data set spanning maximum ten years (1998-2007). Data from GPS permanent stations maintained from different institutions and the recent RING network, settled in Italy in the last five years by the Istituto Nazionale di Geofisica e Vulcanologia, were included into the analysis. Two dimensional strain and rotation rate fields were estimated by the distance weighted approach on a regularly spaced grid (30*30km), estimating the strain using all stations, but data from each station are weighted by their distance from the grid node by a constant a=70km that specifies how the effect of a station decays with distance from the node grid interpolation. Results show that most of the shortening of the Africa-Eurasia relative motion is distributed in the northwestern side offshore Sicily, whereas the extension becomes comparable with shortening on the western border of the Capo d'Orlando basin, and grater in the northeastern side, offshore Sicily, as directly provided by GPS velocities which show a larger E-ward component of sites located in Calabria with respect to those located either in northern Sicily or in the Ustica-Aeolian islands. Moreover, where shortening and extension have mostly a similar order of magnitude, two rotation rate fields can be detected, CCW in the northwestern side of Sicily, and CW in the northeastern one respectively. Also, 2-D dilatation field records a similar pattern, with negative values (shortening) in the northwestern area of Sicily close to the Ustica island, and positive values (extension) in the northeastern and southeastern ones, respectively. Principal shortening and extension rate axes are consistent with long-term geological features: seismic reflection profiles acquired in the southern Tyrrhenian seismogenic belt show active extensional faults affecting Pleistocene strata and deforming the seafloor in the western sector of the Cefalù Basin, on both NE-SW and W-E trending faults. Combining geodetic data and geological features contributes to the knowledge of the active deformation along the Africa-Eurasia plate boundary, suggesting coexisting, independent geodynamic processes, i.e., active E-W backarc spreading in the hangingwall of the Apennines subduction zone, and shortening of the southern margin of the Tyrrhenian backarc basin operated by the "Africa" NW-motion relative to "Europe".

The GPS Topex/Poseidon precise orbit determination experiment - Implications for design of GPS global networks

NASA Technical Reports Server (NTRS)

Lindqwister, Ulf J.; Lichten, Stephen M.; Davis, Edgar S.; Theiss, Harold L.

1993-01-01

Topex/Poseidon, a cooperative satellite mission between United States and France, aims to determine global ocean circulation patterns and to study their influence on world climate through precise measurements of sea surface height above the geoid with an on-board altimeter. To achieve the mission science aims, a goal of 13-cm orbit altitude accuracy was set. Topex/Poseidon includes a Global Positioning System (GPS) precise orbit determination (POD) system that has now demonstrated altitude accuracy better than 5 cm. The GPS POD system includes an on-board GPS receiver and a 6-station GPS global tracking network. This paper reviews early GPS results and discusses multi-mission capabilities available from a future enhanced global GPS network, which would provide ground-based geodetic and atmospheric calibrations needed for NASA deep space missions while also supplying tracking data for future low Earth orbiters. Benefits of the enhanced global GPS network include lower operations costs for deep space tracking and many scientific and societal benefits from the low Earth orbiter missions, including improved understanding of ocean circulation, ocean-weather interactions, the El Nino effect, the Earth thermal balance, and weather forecasting.

Learning-based computing techniques in geoid modeling for precise height transformation

NASA Astrophysics Data System (ADS)

Erol, B.; Erol, S.

2013-03-01

Precise determination of local geoid is of particular importance for establishing height control in geodetic GNSS applications, since the classical leveling technique is too laborious. A geoid model can be accurately obtained employing properly distributed benchmarks having GNSS and leveling observations using an appropriate computing algorithm. Besides the classical multivariable polynomial regression equations (MPRE), this study attempts an evaluation of learning based computing algorithms: artificial neural networks (ANNs), adaptive network-based fuzzy inference system (ANFIS) and especially the wavelet neural networks (WNNs) approach in geoid surface approximation. These algorithms were developed parallel to advances in computer technologies and recently have been used for solving complex nonlinear problems of many applications. However, they are rather new in dealing with precise modeling problem of the Earth gravity field. In the scope of the study, these methods were applied to Istanbul GPS Triangulation Network data. The performances of the methods were assessed considering the validation results of the geoid models at the observation points. In conclusion the ANFIS and WNN revealed higher prediction accuracies compared to ANN and MPRE methods. Beside the prediction capabilities, these methods were also compared and discussed from the practical point of view in conclusions.

Employing Tropospheric Numerical Weather Prediction Model for High-Precision GNSS Positioning

NASA Astrophysics Data System (ADS)

Alves, Daniele; Gouveia, Tayna; Abreu, Pedro; Magário, Jackes

2014-05-01

In the past few years is increasing the necessity of realizing high accuracy positioning. In this sense, the spatial technologies have being widely used. The GNSS (Global Navigation Satellite System) has revolutionized the geodetic positioning activities. Among the existent methods one can emphasize the Precise Point Positioning (PPP) and network-based positioning. But, to get high accuracy employing these methods, mainly in real time, is indispensable to realize the atmospheric modeling (ionosphere and troposphere) accordingly. Related to troposphere, there are the empirical models (for example Saastamoinen and Hopfield). But when highly accuracy results (error of few centimeters) are desired, maybe these models are not appropriated to the Brazilian reality. In order to minimize this limitation arises the NWP (Numerical Weather Prediction) models. In Brazil the CPTEC/INPE (Center for Weather Prediction and Climate Studies / Brazilian Institute for Spatial Researches) provides a regional NWP model, currently used to produce Zenithal Tropospheric Delay (ZTD) predictions (http://satelite.cptec.inpe.br/zenital/). The actual version, called eta15km model, has a spatial resolution of 15 km and temporal resolution of 3 hours. In this paper the main goal is to accomplish experiments and analysis concerning the use of troposphere NWP model (eta15km model) in PPP and network-based positioning. Concerning PPP it was used data from dozens of stations over the Brazilian territory, including Amazon forest. The results obtained with NWP model were compared with Hopfield one. NWP model presented the best results in all experiments. Related to network-based positioning it was used data from GNSS/SP Network in São Paulo State, Brazil. This network presents the best configuration in the country to realize this kind of positioning. Actually the network is composed by twenty stations (http://www.fct.unesp.br/#!/pesquisa/grupos-de-estudo-e-pesquisa/gege//gnss-sp-network2789/). The results obtained employing NWP model also were compared to Hopfield one, and the results were very interesting. The theoretical concepts, experiments, results and analysis will be presented in this paper.

Wavelet based comparison of high frequency oscillations in the geodetic and fluid excitation functions of polar motion

NASA Astrophysics Data System (ADS)

Kosek, W.; Popinski, W.; Niedzielski, T.

2011-10-01

It has been already shown that short period oscillations in polar motion, with periods less than 100 days, are very chaotic and are responsible for increase in short-term prediction errors of pole coordinates data. The wavelet technique enables to compare the geodetic and fluid excitation functions in the high frequency band in many different ways, e.g. by looking at the semblance function. The waveletbased semblance filtering enables determination the common signal in both geodetic and fluid excitation time series. In this paper the considered fluid excitation functions consist of the atmospheric, oceanic and land hydrology excitation functions from ECMWF atmospheric data produced by IERS Associated Product Centre Deutsches GeoForschungsZentrum, Potsdam. The geodetic excitation functions have been computed from the combined IERS pole coordinates data.

EPOS-IP WP10: services and data provision for the GNSS community

NASA Astrophysics Data System (ADS)

Fernandes, Rui

2016-04-01

The EPOS-IP WP10 - "GNSS Data & Products" is the Working Package of the EPOS-IP project in charge of implementing the necessary services in order that the geo-sciences community can access the existing Pan-European Geodetic Infrastructures. The WP10 is formed by representatives of the participating institutions (10) but it is also open to the entire geodetic community. In fact, WP10 also includes members from other institutions/countries that formally are not participating in the EPOS-IP. During the EPOS-IP project, the geodetic component of EPOS (WP10) is dealing essentially with Research Infrastructures focused on continuous operating GNSS (cGNSS). The option of concentrating the efforts on the presently most generalized geodetic tool supporting research on Solid Earth was decided in order to optimize the existing resources. Furthermore, although the focus is on Solid Earth applications, other research and technical applications (e.g., reference frames, meteorology, space weather) can also benefit from the efforts of WP10 towards the optimization of the geodetic resources in Europe. We will present and discuss the plans for the implementation of the thematic and core services (TCS) for GNSS data within EPOS and the related business plan. We will focus on strategies towards the implementation of the best solutions that will permit to the end-users, and in particular geo-scientists, to access the geodetic data, derived solutions, and associated metadata using transparent and uniform processes. The collaboration with EUREF is also an essential component of the implementation plan.

20 CFR 404.1312 - World War II service included.

Code of Federal Regulations, 2013 CFR

2013-04-01

... the United States Coast and Geodetic Survey and were— (1) During the World War II period— (i... authority; (e) Active service of an allied country during the World War II period and— (1) Had entered into... 20 Employees' Benefits 2 2013-04-01 2013-04-01 false World War II service included. 404.1312...

20 CFR 404.1312 - World War II service included.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the United States Coast and Geodetic Survey and were— (1) During the World War II period— (i... authority; (e) Active service of an allied country during the World War II period and— (1) Had entered into... 20 Employees' Benefits 2 2012-04-01 2012-04-01 false World War II service included. 404.1312...

20 CFR 404.1312 - World War II service included.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the United States Coast and Geodetic Survey and were— (1) During the World War II period— (i... authority; (e) Active service of an allied country during the World War II period and— (1) Had entered into... 20 Employees' Benefits 2 2014-04-01 2014-04-01 false World War II service included. 404.1312...

IAA Correlator Center

NASA Technical Reports Server (NTRS)

Surkis, Igor; Ken, Voitsekh; Melnikov, Alexey; Mishin, Vladimir; Sokolova, Nadezda; Shantyr, Violet; Zimovsky, Vladimir

2013-01-01

The activities of the six-station IAA RAS correlator include regular processing of national geodetic VLBI programs Ru-E, Ru-U, and Ru-F. The Ru-U sessions have been transferred in e-VLBI mode and correlated in the IAA Correlator Center automatically since 2011. The DiFX software correlator is used at the IAA in some astrophysical experiments.

Contribution of SELENE-2 geodetic measurements to constrain the lunar internal structure

NASA Astrophysics Data System (ADS)

Matsumoto, K.; Kikuchi, F.; Yamada, R.; Iwata, T.; Kono, Y.; Tsuruta, S.; Hanada, H.; Goossens, S. J.; Ishihara, Y.; Kamata, S.; Sasaki, S.

2012-12-01

Internal structure and composition of the Moon provide important clue and constraints on theories for how the Moon formed and evolved. The Apollo seismic network has contributed to the internal structure modeling. Efforts have been made to detect the lunar core from the noisy Apollo data (e.g., [1], [2]), but there is scant information about the structure below the deepest moonquakes at about 1000 km depth. On the other hand, there have been geodetic studies to infer the deep structure of the Moon. For example, LLR (Lunar Laser Ranging) data analyses detected a displacement of the lunar pole of rotation, indicating that dissipation is acting on the rotation arising from a fluid core [3]. Bayesian inversion using geodetic data (such as mass, moments of inertia, tidal Love numbers k2 and h2, and quality factor Q) also suggests a fluid core and partial melt in the lower mantle region [4]. Further improvements in determining the second-degree gravity coefficients (which will lead to better estimates of moments of inertia) and the Love number k2 will help us to better constrain the lunar internal structure. Differential VLBI (Very Long Baseline Interferometry) technique, which was used in the Japanese lunar exploration mission SELENE (Sept. 2007 - June 2009), is expected to contribute to better determining the second-degree potential Love number k2 and low-degree gravity coefficients. SELENE will be followed by the future lunar mission SELENE-2 which will carry both a lander and an orbiter. We propose to put the SELENE-type radio sources on these spacecraft in order to accurately estimate k2 and the low-degree gravity coefficients. By using the same-beam VLBI tracking technique, these parameters will be retrieved through precision orbit determination of the orbiter with respect to the lander which serves as a reference. The VLBI mission with the radio sources is currently one of the mission candidates for SELENE-2. We have conducted a preliminary simulation study on the anticipated k2 accuracy. With the assumed mission duration of about 3 months and the arc length of 14 days, the k2 accuracy is estimated to be better than 1 %, where the uncertainty is evaluated as 10 times the formal error considering the errors in the non-conservative force modeling and in the lander position. We carried out a feasibility study using Bayesian inversion on how well we can constrain the lunar internal structure by the geodetic data to be improved by SELENE-2. It will be shown that such improved geodetic data contribute to narrow the range of the plausible internal structure models, but there are still trade-offs among crust, mantle, and core structures. Preliminary simulation results will be presented to show that the accuracy of core structure estimation will be improved in consequence of better determination of the mantle structure by combining the geodetic data with the seismic data. References [1] Weber et al. (2011), Science, 331, 309-312, doi:10.1126/science.1199375 [2] Garcia eta l. (2011), PEPI, doi:10.1016/j.pepi.2011.06.015 [3] Williams et al. (2001), JGR, 106, E11, 27,933-27,968 [4] Khan and Mosegaard (2005), GRL, 32, L22203, doi:10.1029/2005GL023985

Demonstration of the Cascadia G‐FAST geodetic earthquake early warning system for the Nisqually, Washington, earthquake

USGS Publications Warehouse

Crowell, Brendan; Schmidt, David; Bodin, Paul; Vidale, John; Gomberg, Joan S.; Hartog, Renate; Kress, Victor; Melbourne, Tim; Santillian, Marcelo; Minson, Sarah E.; Jamison, Dylan

2016-01-01

A prototype earthquake early warning (EEW) system is currently in development in the Pacific Northwest. We have taken a two‐stage approach to EEW: (1) detection and initial characterization using strong‐motion data with the Earthquake Alarm Systems (ElarmS) seismic early warning package and (2) the triggering of geodetic modeling modules using Global Navigation Satellite Systems data that help provide robust estimates of large‐magnitude earthquakes. In this article we demonstrate the performance of the latter, the Geodetic First Approximation of Size and Time (G‐FAST) geodetic early warning system, using simulated displacements for the 2001Mw 6.8 Nisqually earthquake. We test the timing and performance of the two G‐FAST source characterization modules, peak ground displacement scaling, and Centroid Moment Tensor‐driven finite‐fault‐slip modeling under ideal, latent, noisy, and incomplete data conditions. We show good agreement between source parameters computed by G‐FAST with previously published and postprocessed seismic and geodetic results for all test cases and modeling modules, and we discuss the challenges with integration into the U.S. Geological Survey’s ShakeAlert EEW system.

The Current Status and Tendency of China Millimeter Coordinate Frame Implementation and Maintenance

NASA Astrophysics Data System (ADS)

Cheng, P.; Cheng, Y.; Bei, J.

2017-12-01

China Geodetic Coordinate System 2000 (CGCS2000) was first officially declared as the national standard coordinate system on July 1, 2008. This reference frame was defined in the ITRF97 frame at epoch 2000.0 and included 2600 GPS geodetic control points. The paper discusses differences between China Geodetic Coordinate System 2000 (CGCS2000) and later updated ITRF versions, such as ITRF2014,in terms of technical implementation and maintenance. With the development of the Beidou navigation satellite system, especially third generation of BDS with signal global coverage in the future, and with progress of space geodetic technology, it is possible for us to establish a global millimeter-level reference frame based on space geodetic technology including BDS. The millimeter reference frame implementation concerns two factors: 1) The variation of geocenter motion estimation, and 2) the site nonlinear motion modeling. In this paper, the geocentric inversion methods are discussed and compared among results derived from various technical methods. Our nonlinear site movement modeling focuses on singular spectrum analysis method, which is of apparent advantages over earth physical effect modeling. All presented in the paper expected to provide reference to our future CGCS2000 maintenance.

Integration of space geodesy: a US National Geodetic Observatory

NASA Technical Reports Server (NTRS)

Yunck, Thomas P.; Neilan, Ruth

2003-01-01

In the interest of improving the performance and efficiency of space geodesy a diverse group in the U.S., in collaboration with IGGOS, has begun to establish a unified National Geodetic Observatory (NGO).

National geodetic satellite program, part 2

NASA Technical Reports Server (NTRS)

Schmid, H.

1977-01-01

Satellite geodesy and the creation of worldwide geodetic reference systems is discussed. The geometric description of the surface and the analytical description of the gravity field of the earth by means of worldwide reference systems, with the aid of satellite geodesy, are presented. A triangulation method based on photogrammetric principles is described in detail. Results are derived in the form of three dimensional models. These mathematical models represent the frame of reference into which one can fit the existing geodetic results from the various local datums, as well as future measurements.

Italy INAF Analysis Center Report

NASA Technical Reports Server (NTRS)

Negusini, M.; Sarti, P.

2013-01-01

This report summarizes the activity of the Italian INAF VLBI Analysis Center. Our Analysis Center is located in Bologna, Italy and belongs to the Institute of Radioastronomy, which is part of the National Institute of Astrophysics. IRA runs the observatories of Medicina and Noto, where two 32-m VLBI AZ-EL telescopes are situated. This report contains the AC's VLBI data analysis activities and shortly outlines the investigations into the co-locations of space geodetic instruments.

PBO Nucleus Project Summary: The Successful Integration of 209 Existing GPS Sions in the Plate Boundary Observatory

NASA Astrophysics Data System (ADS)

Blume, F.; Miller, M.; Boyce, E.; Borsa, A.; Eriksson, S.

2008-12-01

Tectonic and earthquake research in the US has experienced a quiet revolution over the last decade precipitated by the recognition that slow-motion faulting events can both trigger and be triggered by regular earthquakes. Transient motion has now been found in essentially all tectonic environments, and the detection and analysis of such events is the first-order science target of the EarthScope Project. Because of this and a host of other fundamental tectonics questions that can be answered only with long-duration geodetic time series, the 1100-station EarthScope Plate Boundary Observatory (PBO) network was designed to leverage 445 existing continuous GPS stations whose measurements extend back over a decade. The irreplaceable recording history of these stations will accelerate EarthScope scientific return by providing the highest possible resolution. This resolution will be used to detect and understand transients, to determine the three-dimensional velocity field (particularly vertical motion), and to improve measurement precision by understanding the complex noise sources inherent in GPS. The PBO Nucleus project supports the operation, maintenance and hardware upgrades of a subset of the six western U.S. geodetic networks until they are subsumed by PBO. Uninterrupted data flow from these stations will effectively double the time-series length of PBO over the expected life of EarthScope, and has created, for the first time, a single GPS-based geodetic network in the US. The other existing sites remain in operation under support from non-NSF sources (e.g. the USGS), and EarthScope continues to benefit from their continued operation On the grounds of relevance to EarthScope science goals, geographic distribution and data quality, 209 of the 432 existing stations were selected as the nucleus upon which to build PBO. Conversion of these stations to a PBO-compatible mode of operation was begun under previous funding, and as a result data now flow directly to PBO archives and processing centers while maintenance, operations, and meta-data requirements are continue to be upgraded to PBO standards. At the end of this project all 209 stations have been fully incorporated into PBO, meeting all standards for new PBO construction including data communications and land use permits. Funds for operation of these stations have been included in approved budgets for PBO's Operations and Maintenance phase. The data from these stations serve a much larger audience than just the few people who work to keep them operating. This project is now collecting the data that will be used by the next generation of solid-earth researchers for at least two decades. Educational modules are being developed by a team of researchers, educators, and curriculum development professionals, and are being disseminated through regional and national workshops. An interactive website provides the newest developments in tectonics research to K-16 classrooms. class="ab'>

Deployment operation of NanTroSEIZE C0002 riserless LTBMS

NASA Astrophysics Data System (ADS)

Kyo, N.; Saruhashi, T.; Sawada, I.; Namba, Y.; Kitada, K.; Kimura, T.; Toczko, S.; Araki, E.; Kopf, A.; IODP EXP 332 Scientists

2011-12-01

The installation of LTBMS (Long Term Borehole Monitoring System) for NanTroSEIZE (Nankai Trough Seismogenic Zone Experiment) C0002 riserless hole was successfully carried out as part of IODP Expedition 332 operations by DV Chikyu in November - December 2010. The water depth of the site and penetration depth of the hole are 1937.5 m and 980 mbsf respectively. Casing (9-5/8") was set to the depth of 888 mbsf and below the CORK head, 3-1/2" tubing was deployed inside the casing as the support structure for the downhole instruments. Within the rat hole section, two pressure ports, a strain meter, a tilt meter, a broadband seismometer, geophone, and accelerometer were deployed. These seismic and geodetic sensors were set within the borehole, and coupled to the formation via cement whose physical properties (Young's modulus, Poisson's ratio, density) were adjusted to fit the formation's properties. Screen sections were set to access the pore fluids, while isolating them from the sea floor and the lower lithological units by a swellable packer, and cement, respectively. At the top of wellhead, and at the apex of the 3-1/2" tubing assembly, a CORK head was landed. The CORK head holds the pressure sensor unit (4 pressure sensors), underwater mateable data connectors (connected to the cemented sensors), and hydraulic valves to access and sample formation fluids by ROV. The major scientific features of the Hole C0002G (riserless) LTBMS are sensors monitoring multiple parameters related to seismic, geodetic and pore fluid behavior simultaneously at distinct, multiple, layers within the same borehole. The main technical difficulties in the LTBMS development are as follows: (1) Reduction method for current-induced VIV (Vortex Induced Vibration) (2) Borehole coupling for seismic and geodetic sensors (3) Anti-vibration/shock and protection method for borehole sensors/instruments (4) Attachment and protection for sensor cables and pressure lines (5) Zone isolation for multi-layer pressure measurements (6) Wellhead system (CORK) for data connection to submarine cable network (7) Downsizing borehole instruments (installation with 3-1/2-in tubing) (8) System reliability (redundant sensor system) We carried out sea trials using a dummy sensor assembly to study the effects of deploying the assembly in strong currents, and also carried out additional pool experiments and numerical simulations to evaluate VIV countermeasures. Through shock and vibration mechanical tests, we improved the robustness of sensors and the sensor carrier. As part of these investigations, we conducted risk analysis based on the operation, science, and engineering points of view from, which helped clarify operational procedures for actual deployment. Future plans include returning to Hole C0002G site to deploy a data logger and battery for temporary observations. After examining the data quality, we'll finally connect the LTBMS to the DONET (Dense Oceanfloor Network System for Earthquakes and Tsunamis) submarine cabled network. Plans are also underway for deploying more LTBMS's into Site C0010 (riserless) and Site C0002 (riser).

Monitoring Sea Level by Tide Gauges and GPS at Barcelona and Estartit Harbours

NASA Astrophysics Data System (ADS)

Martinez Benjamin, J. J.; Gili, J.; Lopez, R.; Tapia, A.; Bosch, E.; Perez, B.; Pros, F.

2012-04-01

Sea level is an environmental variable which is widely recognised as being important in many scientific disciplines as a control parameter for coastal dynamical processes or climate processes in the coupled atmosphere-ocean systems, as well as engineering applications. A major source of sea-level data are the national networks of coastal tide gauges, in Spain belonging to different institutions as the Instituto Geográfico Nacional (IGN), Puertos del Estado (PE), Instituto Hidrográfico de la Marina (IHM), etc. The tide gauge of l'Estartit is a traditional floating gauge placed 21 years ago and has an accuracy of ± 2 mm. Since 1996, l'Estartit tide gauge has been co-located with geodetic techniques (GPS measurements of XU, Utilitary Network, and XdA, Levelling Network,) and it is tied to the SPGIC (Integrated Geodetic Positioning System of Catalonia) project of the Cartographic Institute of Catalunya (ICC). In 2006, due to the work for the expansion of the harbour, the tide gauge had to be moved. Before the work started, appropiate GPS measurements were carried out in order to ensure the connection of the tide gauge data. During October 2006 and May 2008, the tide gauge was inactive and it has been moved on to a new location inside the harbour. In June 2008, new GPS and levelling measures have been done in order to tie the new location into SPGIC project and to co-locate old data respect the new one. Although l'Estartit does not have a GPS permanent station, it is possible to build a virtual one from the service "CATNET web" of the ICC. "CATNET web" is a data distribution system of a virtual GPS permanent station via web. From the coordinates where you want to place the virtual station, the time interval and the measurement rate, the system generates a RINEX file under the requested conditions. At Barcelona harbour there is one MIROS radar tide gauge belonging to Puertos del Estado (Spanish Harbours). It is placed at the dock 140 of the ENAGAS Building.The radar sensor is over the water surface, on a L-shaped structure which elevates it a few meters above the quay shelf. 1-min data are transmitted to the ENAGAS Control Center by cable and then sent each 1 min to Puertos del Estado by e-mail.This sensor also measures agitation and sends wave parameters each 20 min. A provisional tide gauge bench mark has been defined while the levelling has being done. There is a GPS station Leica Geosystems GRX1200 GG Pro and antenna 1202. Bathymetric campaigns inside the harbour have been made. The presentation is directed to the description of the actual situation of the geodetic infrastructure of Barcelona and l'Estartit sites for sea level determination and contribution to regional sea level rise.

Mixed-Mode Slip Behavior of the Altotiberina Low-Angle Normal Fault System (Northern Apennines, Italy) through High-Resolution Earthquake Locations and Repeating Events

NASA Astrophysics Data System (ADS)

Valoroso, Luisa; Chiaraluce, Lauro; Di Stefano, Raffaele; Monachesi, Giancarlo

2017-12-01

We generated a 4.5-year-long (2010-2014) high-resolution earthquake catalogue, composed of 37,000 events with ML < 3.9 and MC = 0.5 completeness magnitude, to report on the seismic activity of the Altotiberina (ATF) low-angle normal fault system and to shed light on the mechanical behavior and seismic potential of this fault, which is capable of generating a M7 event. Seismicity defines the geometry of the fault system composed of the low-angle (15°-20°) ATF, extending for 50 km along strike and between 4 and 16 km at depth showing an 1.5 km thick fault zone made of multiple subparallel slipping planes, and a complex network of synthetic/antithetic higher-angle segments located in the ATF hanging wall (HW) that can be traced along strike for up to 35 km. Ninety percent of the recorded seismicity occurs along the high-angle HW faults during a series of minor, sometimes long-lasting (months) seismic sequences with multiple MW3+ mainshocks. Remaining earthquakes (ML < 2.4) are released instead along the low-angle ATF at a constant rate of 2.2 events per day. Within the ATF-related seismicity, we found 97 clusters of repeating earthquakes (RE), mostly consisting of doublets occurring during short interevent time (hours). RE are located within the geodetically recognized creeping portions of the ATF, around the main locked asperity. The rate of occurrence of RE seems quite synchronous with the ATF-HW seismic release, suggesting that creeping may guide the strain partitioning in the ATF system. The seismic moment released by the ATF seismicity accounts for 30% of the geodetic one, implying aseismic deformation. The ATF-seismicity pattern is thus consistent with a mixed-mode (seismic and aseismic) slip behavior.

Spatio-temporal mapping of plate boundary faults in California using geodetic imaging

USGS Publications Warehouse

Donnellan, Andrea; Arrowsmith, Ramon; DeLong, Stephen B.

2017-01-01

The Pacific–North American plate boundary in California is composed of a 400-km-wide network of faults and zones of distributed deformation. Earthquakes, even large ones, can occur along individual or combinations of faults within the larger plate boundary system. While research often focuses on the primary and secondary faults, holistic study of the plate boundary is required to answer several fundamental questions. How do plate boundary motions partition across California faults? How do faults within the plate boundary interact during earthquakes? What fraction of strain accumulation is relieved aseismically and does this provide limits on fault rupture propagation? Geodetic imaging, broadly defined as measurement of crustal deformation and topography of the Earth’s surface, enables assessment of topographic characteristics and the spatio-temporal behavior of the Earth’s crust. We focus here on crustal deformation observed with continuous Global Positioning System (GPS) data and Interferometric Synthetic Aperture Radar (InSAR) from NASA’s airborne UAVSAR platform, and on high-resolution topography acquired from lidar and Structure from Motion (SfM) methods. Combined, these measurements are used to identify active structures, past ruptures, transient motions, and distribution of deformation. The observations inform estimates of the mechanical and geometric properties of faults. We discuss five areas in California as examples of different fault behavior, fault maturity and times within the earthquake cycle: the M6.0 2014 South Napa earthquake rupture, the San Jacinto fault, the creeping and locked Carrizo sections of the San Andreas fault, the Landers rupture in the Eastern California Shear Zone, and the convergence of the Eastern California Shear Zone and San Andreas fault in southern California. These examples indicate that distribution of crustal deformation can be measured using interferometric synthetic aperture radar (InSAR), Global Navigation Satellite System (GNSS), and high-resolution topography and can improve our understanding of tectonic deformation and rupture characteristics within the broad plate boundary zone.

Application of the Deformation Information System for automated analysis and mapping of mining terrain deformations - case study from SW Poland

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Grzempowski, Piotr; Milczarek, Wojciech; Nowacka, Anna

2015-04-01

Monitoring, mapping and modelling of mining induced terrain deformations are important tasks for quantifying and minimising threats that arise from underground extraction of useful minerals and affect surface infrastructure, human safety, the environment and security of the mining operation itself. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and expanding with the progress in geographical information technologies. These include for example: terrestrial geodetic measurements, Global Navigation Satellite Systems, remote sensing, GIS based modelling and spatial statistics, finite element method modelling, geological modelling, empirical modelling using e.g. the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The presentation shows the results of numerical modelling and mapping of mining terrain deformations for two cases of underground mining sites in SW Poland, hard coal one (abandoned) and copper ore (active) using the functionalities of the Deformation Information System (DIS) (Blachowski et al, 2014 @ http://meetingorganizer.copernicus.org/EGU2014/EGU2014-7949.pdf). The functionalities of the spatial data modelling module of DIS have been presented and its applications in modelling, mapping and visualising mining terrain deformations based on processing of measurement data (geodetic and GNSS) for these two cases have been characterised and compared. These include, self-developed and implemented in DIS, automation procedures for calculating mining terrain subsidence with different interpolation techniques, calculation of other mining deformation parameters (i.e. tilt, horizontal displacement, horizontal strain and curvature), as well as mapping mining terrain categories based on classification of the values of these parameters as used in Poland. Acknowledgments. This work has been financed from the National Science Centre Project "Development of a numerical method of mining ground deformation modelling in complex geological and mining conditions" UMO-2012/07/B/ST10/04297 executed at the Faculty of Geoengineering, Mining and Geology of the Wroclaw University of Technology (Poland).

INVESTIGATION OF CRUSTAL MOTION IN THE TIEN SHAN USING INSAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mellors, R J

2011-02-25

The northern Tien Shan of Central Asia is an area of active mid-continent deformation. Although far from a plate boundary, this region has experienced 5 earthquakes larger than magnitude 7 in the past century and includes one event that may as be as large as Mw 8.0. Previous studies based on GPS measurements indicate on the order of 23 mm/yr of shortening across the entire Tien Shan and up to 15 mm/year in the northern Tien Shan (Figure 1). The seismic moment release rate appears comparable with the geodetic measured slip, at least to first order, suggesting that geodetic ratesmore » can be considered a proxy for accumulation rates of stress for seismic hazard estimation. Interferometric synthetic aperture radar may provide a means to make detailed spatial measurements and hence in identifying block boundaries and assisting in seismic hazard. Therefore, we hoped to define block boundaries by direct measurement and by identifying and resolving earthquake slip. Due to political instability in Kyrgzystan, the existing seismic network has not performed as well as required to precisely determine earthquake hypocenters in remote areas and hence InSAR is highly useful. In this paper we present the result of three earthquake studies and show that InSAR is useful for refining locations of teleseismically located earthquakes. ALOS PALSAR data is used to investigate crustal motion in the Tien Shan mountains of Central Asia. As part of the work, considerable software development was undertaken to process PALSAR data. This software has been made freely available. Two damaging earthquakes have been imaged in the Tien Shan and the locations provided by ALOS InSAR have helped to refine seismological velocity models. A third earthquake south of Kyrgyzstan was also imaged. The use of InSAR data and especially L band is therefore very useful in providing groundtruth for earthquake locations.« less

Spatial Distribution of earthquakes off the coast of Fukushima Two Years after the M9 Earthquake: the Southern Area of the 2011 Tohoku Earthquake Rupture Zone

NASA Astrophysics Data System (ADS)

Yamada, T.; Nakahigashi, K.; Shinohara, M.; Mochizuki, K.; Shiobara, H.

2014-12-01

Huge earthquakes cause vastly stress field change around the rupture zones, and many aftershocks and other related geophysical phenomenon such as geodetic movements have been observed. It is important to figure out the time-spacious distribution during the relaxation process for understanding the giant earthquake cycle. In this study, we pick up the southern rupture area of the 2011 Tohoku earthquake (M9.0). The seismicity rate keeps still high compared with that before the 2011 earthquake. Many studies using ocean bottom seismometers (OBSs) have been doing since soon after the 2011 Tohoku earthquake in order to obtain aftershock activity precisely. Here we show one of the studies at off the coast of Fukushima which is located on the southern part of the rupture area caused by the 2011 Tohoku earthquake. We deployed 4 broadband type OBSs (BBOBSs) and 12 short-period type OBSs (SOBS) in August 2012. Other 4 BBOBSs attached with absolute pressure gauges and 20 SOBSs were added in November 2012. We recovered 36 OBSs including 8 BBOBSs in November 2013. We selected 1,000 events in the vicinity of the OBS network based on a hypocenter catalog published by the Japan Meteorological Agency, and extracted the data after time corrections caused by each internal clock. Each P and S wave arrival times, P wave polarity and maximum amplitude were picked manually on a computer display. We assumed one dimensional velocity structure based on the result from an active source experiment across our network, and applied time corrections every station for removing ambiguity of the assumed structure. Then we adopted a maximum-likelihood estimation technique and calculated the hypocenters. The results show that intensive activity near the Japan Trench can be seen, while there was a quiet seismic zone between the trench zone and landward high activity zone.

Volcano Geodesy: Recent developments and future challenges

USGS Publications Warehouse

Fernandez, Jose F.; Pepe, Antonio; Poland, Michael; Sigmundsson, Freysteinn

2017-01-01

Ascent of magma through Earth's crust is normally associated with, among other effects, ground deformation and gravity changes. Geodesy is thus a valuable tool for monitoring and hazards assessment during volcanic unrest, and it provides valuable data for exploring the geometry and volume of magma plumbing systems. Recent decades have seen an explosion in the quality and quantity of volcano geodetic data. New datasets (some made possible by regional and global scientific initiatives), as well as new analysis methods and modeling practices, have resulted in important changes to our understanding of the geodetic characteristics of active volcanism and magmatic processes, from the scale of individual eruptive vents to global compilations of volcano deformation. Here, we describe some of the recent developments in volcano geodesy, both in terms of data and interpretive tools, and discuss the role of international initiatives in meeting future challenges for the field.

An integrated geodetic and seismic study of the Cusco Fault system in the Cusco Region-Southern Peru

NASA Astrophysics Data System (ADS)

Norabuena, E. O.; Tavera, H. J.

2017-12-01

The Cusco Fault system is composed by six main faults (Zurite, Tamboray, Qoricocha, Tambomachay, Pachatusan, and Urcos) extending in a NW-SE direction over the Cusco Region in southeastern Peru. From these, the Tambomachay is a normal fault of 20 km length, strikes N120°E and bounds a basin filled with quaternary lacustrine and fluvial deposits. Given its 5 km distance to Cusco, an historical and Inca's archeological landmark, it represents a great seismic hazard for its more than 350,000 inhabitants. The Tambomachay fault as well as the other secondary faults have been a source of significant seismic activity since historical times being the more damaging ones the Cusco earthquakes of 1650, 1950 and more recently April 1986 (M 5.8). Previous geological studies indicate that at the beginning of the Quaternary the fault showed a transcurrent mechanism leading to the formation of the Cusco basin. However, nowadays its mechanism is normal fault and scarps up to 22m can be observed. We report the current dynamics of the Tambomachay fault and secondary faults based on seismic activity imaged by a network of 29 broadband stations deployed in the Cusco Region as well as the deformation field inferred from GPS survey measurements carried out between 2014 and 2016.

Modern Geodetic Measurement Techniques in Gravimetric Studies on the Example of Gypsum Karst in the Siesławice Region

NASA Astrophysics Data System (ADS)

Porzucek, Sławomir; Łój, Monika; Matwij, Karolina; Matwij, Wojciech

2018-03-01

In the region of Siesławice (near Busko-Zdrój, Poland) there are unique phenomena of gypsum karst. Atmospheric factors caused numerous gypsum outcrops, canals and underground voids. The article presents the possibility of using non-invasive gravimetric surveys supplemented with geodetic measurements to illustrate karst changes occurring around the void. The use of modern geodetic measurement techniques including terrestrial and airborne laser scanning enables to generate a digital terrain model and a three-dimensional model of voids. Gravimetric field studies allowed to map the anomalies of the gravitational field of the near-surface zone. Geodetic measurement results have made it possible to accurately determine the terrain correction that supplemented the gravimetric anomaly information. Geophysical interpretation indicate the presence of weathered rocks in the near surface zone and fractures and loosened zones located surround the karst cave.

Ice cap melting and low-viscosity crustal root explain the narrow geodetic uplift of the Western Alps

NASA Astrophysics Data System (ADS)

Chéry, J.; Genti, M.; Vernant, P.

2016-04-01

More than 10 years of geodetic measurements demonstrate an uplift rate of 1-3 mm/yr of the high topography region of the Western Alps. By contrast, no significant horizontal motion has been detected. Two uplift mechanisms have been proposed: (1) the isostatic response to denudation responsible for only a fraction of the observed uplift and (2) the rebound induced by the Wurmian ice cap melting which predicts a broader uplifting region than the one evidenced by geodetic observations. Using a numerical model to fit the geodetic data, we show that a crustal viscosity contrast between the foreland and the central part of the Alps, the latter being weaker with a viscosity of 1021 Pa s, is needed. The vertical rates are enhanced if the strong uppermost mantle beneath the Moho is interrupted across the Alps, therefore allowing a weak vertical rheological anomaly over the entire lithosphere.

Long-term mass variations from SLR, VLBI and GPS data

NASA Astrophysics Data System (ADS)

Luceri, Vincenza; Sciarretta, Cecilia; Bianco, Giuseppe

2013-04-01

The second-degree geopotential coefficients reflect the behaviour of the Earth's inertia tensor of order 2 which describes the main mass variations of our planet impacting polar motion and length of day (EOP). SLR, VLBI and GPS allow the estimation of those variations, either directly in the case of SLR through its dynamics, and indirectly, for all the three geodetic techniques, by deriving excitation functions from the EOP estimations. The geodetic estimates include the influence of the Earth's atmosphere and oceans, both from their mass and motion components, which can be modelled using the atmospheric and oceanic angular momenta variations. The different C21, S21 and C20 geodetic time series are compared in order to evaluate their coherence and their response to the mass variations after the removal of the motion terms. Moreover, the residual signal contents of the geodetic values, deprived by the atmospheric and oceanic mass and motion components, will be investigated.

Delay estimation in digital correlation interferometers with special consideration of the MK 2 system of the Max-Planck Institute of Radio Astronomy

NASA Astrophysics Data System (ADS)

Beyer, W. K. G.

The estimation accuracy of the group delay measured in a single video frequency band was analyzed as a function of the system bandwidth and the signal to noise ratio. Very long base interferometry (VLBI) measurements from geodetic experiments were used to check the geodetic applicability of the Mark 2 evaluation system. The geodetic observation quantities and the correlation geometry are introduced. The data flow in the VLBI experiment, the correlation analysis, the analyses and evaluation in the MK2 system, and the delay estimation procedure following the least squares method are presented. It is shown that the MK2 system is no longer up to date for geodetic applications. The superiority of the developed estimation method with respect to the interpolation algorithm is demonstrated. The numerical investigations show the deleterious influence of the distorting bit shift effects.

GeoSEA: Geodetic Earthquake Observatory on the Seafloor

NASA Astrophysics Data System (ADS)

Kopp, Heidrun; Lange, Dietrich; Flueh, Ernst R.; Petersen, Florian; Behrmann, Jan-Hinrich; Devey, Colin

2014-05-01

Space geodetic observations of crustal deformation have contributed greatly to our understanding of plate tectonic processes in general, and plate subduction in particular. Measurements of interseismic strain have documented the active accumulation of strain, and subsequent strain release during earthquakes. However, techniques such as GPS cannot be applied below the water surface because the electromagnetic energy is strongly attenuated in the water column. Evidence suggests that much of the elastic strain build up and release (and particularly that responsible for both tsunami generation and giant earthquakes) occurs offshore. To quantify strain accumulation and assess the resultant hazard potential we urgently need systems to resolve seafloor crustal deformation. Here we report on first results of sea trials of a newly implemented seafloor geodesy array. The GeoSEA (Geodetic Earthquake Observatory on the Seafloor) array consists of a seafloor transponder network comprising 35 units and a wave glider acting as a surface unit (GeoSURF) to ensure satellite correspondence, data transfer and monitor system health. Seafloor displacement occurs in the horizontal (x,y) and vertical direction (z). The vertical displacement is measured by monitoring pressure variations at the seafloor. Horizontal seafloor displacement can be measured either using an acoustic/GPS combination to provide absolute positioning (requiring a suitably equipped vessel to perform repeated cruises to provide the GPS fixes) or by long-term acoustic telemetry between different beacons fixed on the seafloor to determine relative distances by using the travel time observations to each other, which is the technique tested during our short sea trials. For horizontal direct path measurements, the system utilizes acoustic ranging techniques with a ranging precision better than 15 mm and long term stability over 2 km distances. Vertical motion is obtained from pressure gauges. Integrated inclinometers monitor station settlement in two horizontal directions. Data can be acquired and recorded autonomously subsea without system or human intervention for up to 6 years. These data can then be recovered via the integrated high-speed acoustic telemetry link without recovering the seafloor units. When requested to do so, the stored data will be transmitted wirelessly up to the sea surface to the GeoSURF wave glider for onward transmission via a satellite link. Targets for GeoSEA are the marine sector of the North Anatolian fault zone in the Marmara Sea, where a joint French-German array will be installed in late 2014 as well as the central sector of the South America - Nazca convergent plate boundary along the Iquique segment, offshore Northern Chile. Here, the GeoSEA array will be installed in late 2015 to monitor crustal deformation. Mobile autonomous seafloor arrays for continuous measurement of active seafloor deformation in hazard zones have the potential to lead to transformative discoveries of plate boundary/fault zone tectonic processes and address a novel element of marine geophysical research.

Capturing Postseismic Processes of the 2016 Mw 7.1 Kumamoto Earthquake, Japan, Using Dense, Continuous GPS and Short-repeat Time ALOS-2 InSAR Data: Implications for the Shallow Slip Deficit Problem

NASA Astrophysics Data System (ADS)

Milliner, C. W. D.; Burgmann, R.; Wang, T.; Inbal, A.; Bekaert, D. P.; Liang, C.; Fielding, E. J.

2017-12-01

Separating the contribution of shallow coseismic slip from rapidly decaying, postseismic afterslip in surface rupturing events has been difficult to resolve due to the typically sparse configuration of GPS networks and long-repeat time of InSAR acquisitions. Whether shallow fault motion along surface ruptures is a result of coseismic slip, or largely a product of rapid afterslip occurring within the first minutes to days, has significant implications for our understanding of the mechanics and frictional behavior of faulting in the shallow crust. To test this behavior in the case of a major surface rupturing event, we attempt to quantify the co- and postseismic slip of the 2016 Mw 7.1 Kumamoto earthquake sequence using a dense and continuous GPS network ( 10 km spacing), with short-repeat time, ALOS-2 InSAR data. Using the Network Inversion Filter method, we jointly invert the GPS and InSAR data to obtain a time history of afterslip in the first minutes to months following the mainshock. From our initial results, we find no clear evidence of significant shallow afterslip (i.e., no observable slip > 30 cm at depths of < 3 km, a minimum resolvable value), that could account for the 1 m of coseismic deficit of shallow slip inferred from our static finite-fault inversion. Our results show, aside from significant volumetric changes related to poroelastic processes, the majority of shallow fault slip was largely complete after rupture cessation. We also attempt to improve our coseismic slip model by implementing a method that inverts changes in seismicity rates for coseismic slip, helping constrain parts of the model space at depth where geodetic data loses resolving power. The use of geodetic data with the ability to resolve near-field, coseismic deformation and rapidly decaying postseismic processes will aid in our understanding of the frictional properties of shallow faulting, giving more reliable predictions for ground motion simulations and seismic hazard assessments.

Improving deformation models by discounting transient signals in geodetic data: 2. Geodetic data, stress directions, and long-term strain rates in Italy

NASA Astrophysics Data System (ADS)

Carafa, Michele M. C.; Bird, Peter

2016-07-01

The lithosphere of Italy is exposed to a number of different short-term strain transients, including but not limited to landslides, postseismic relaxation, and volcanic inflation/deflation. These transients affect GPS velocities and complicate the assessment of the long-term tectonic component of the surface deformation. In a companion paper we present a method for anticipating the principal patterns of nontectonic, short-term strains and building this information into the covariance matrix of the geodetic velocities. In this work we apply this method to Italian GPS velocities to build an augmented covariance matrix that characterizes all expected discrepancies between short- and long-term velocities. We find that formal uncertainties usually reported for GPS measurements are smaller than the variability of the same benchmarks across a geologic time span. Furthermore, we include in our modeling the azimuths of most compressive horizontal principal stresses (SHmax) because GPS data cannot resolve the active kinematics of coastal and offshore areas. We find that the final tectonic model can be made relatively insensitive to short-term interfering processes if the augmented covariance matrix and SHmax data records are used in the objective function. This results in a preferred neotectonic model that is also in closer agreement with independent geologic and seismological constraints and has the advantage of reducing short-term biases in forecasts of long-term seismicity.

Definition and Proposed Realization of the International Height Reference System (IHRS)

NASA Astrophysics Data System (ADS)

Ihde, Johannes; Sánchez, Laura; Barzaghi, Riccardo; Drewes, Hermann; Foerste, Christoph; Gruber, Thomas; Liebsch, Gunter; Marti, Urs; Pail, Roland; Sideris, Michael

2017-05-01

Studying, understanding and modelling global change require geodetic reference frames with an order of accuracy higher than the magnitude of the effects to be actually studied and with high consistency and reliability worldwide. The International Association of Geodesy, taking care of providing a precise geodetic infrastructure for monitoring the Earth system, promotes the implementation of an integrated global geodetic reference frame that provides a reliable frame for consistent analysis and modelling of global phenomena and processes affecting the Earth's gravity field, the Earth's surface geometry and the Earth's rotation. The definition, realization, maintenance and wide utilization of the International Terrestrial Reference System guarantee a globally unified geometric reference frame with an accuracy at the millimetre level. An equivalent high-precision global physical reference frame that supports the reliable description of changes in the Earth's gravity field (such as sea level variations, mass displacements, processes associated with geophysical fluids) is missing. This paper addresses the theoretical foundations supporting the implementation of such a physical reference surface in terms of an International Height Reference System and provides guidance for the coming activities required for the practical and sustainable realization of this system. Based on conceptual approaches of physical geodesy, the requirements for a unified global height reference system are derived. In accordance with the practice, its realization as the International Height Reference Frame is designed. Further steps for the implementation are also proposed.

Magma-tectonic interactions in Kīlauea's Southwest Rift Zone in 2006 through coupled geodetic/seismological analysis

NASA Astrophysics Data System (ADS)

Wauthier, C.; Roman, D. C.; Poland, M. P.

2015-12-01

For much of the first 20 years of Kīlauea's 1983-present Pu'u 'Ō'ō eruption, deformation was characterized by subsidence at the volcano's summit and along both the East Rift Zone (ERZ) and Southwest Rift Zone (SWRZ). At the end of 2003, however, Kīlauea's summit began a 4-year period of inflation due to a surge in magma supply to the volcano. In 2006, the SWRZ also experienced atypical inflation, which was last observed in 1981-82 during a series of dike intrusions. To investigate the active magma sources and their interactions with faulting in the SWRZ during 2006, we integrate contemporary geodetic data from InSAR and GPS with double-couple fault-plane solutions for volcano-tectonic earthquakes and Coulomb stress modeling. According to the rate of deformation measured in daily GPS data, two distinct periods can be defined, spanning January to 15 March 2006 (period 1) and 16 March to 30 September 2006 (period 2). Geodetic models suggest that, during period 1, deformation, due to pressurization of magma in a vertical prolate-spheroidal conduit, in the south caldera area. In addition, a major seismic swarm occurred in both the SWRZ and ERZ. Our preliminary results also suggest that, during period 2, magma was still overpressurizing the same prolate-spheroid but a subhorizontal sill also intruded further to the southwest in the seismic SWRZ (SSWRZ). The beginning of period 2 also corresponds to a switch from subsidence to inflation of the SWRZ. Faulting in the upper ERZ is primarily strike-slip, with no obvious change in FPS orientation between periods 1 and 2. In contrast, faulting in the upper SSWRZ occurs as dip-slip motion on near-vertical faults. SSWRZ FPS show a mix of orientations including NW- and NE-striking faults, which along with relative earthquake locations, suggest a series of right-stepping fault segments, particularly during period 2. Calculated Coulomb stress changes indicate that faulting in the upper SSWRZ may result from stresses produced by inflation of the geodetically modeled sources described above, in particular the prolate spheroid located in the south caldera area. In contrast, earthquakes in the ERZ are generally inhibited by the geodetically modeled sources, suggesting that another process may be responsible for faulting along the ERZ.

Applications of Morphochronology to the Active Tectonics of Tibet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryerson, F J; Tapponnier, P; Finkel, R C

2005-01-28

The Himalayas and the Tibetan Plateau were formed as a result of the collision of India and Asia, and provide an excellent opportunity to study the mechanical response of the continental lithosphere to tectonic stress. Geophysicists are divided in their views on the nature of this response advocating either (1) homogeneously distributed deformation with the lithosphere deforming as a fluid continuum or (2) deformation is highly localized with the lithosphere that deforms as a system of blocks. The resolution of this issue has broad implications for understanding the tectonic response of continental lithosphere in general. Homogeneous deformation is supported bymore » relatively low decadal, geodetic slip-rate estimates for the Altyn Tagh and Karakorum Faults. Localized deformation is supported by high millennial, geomorphic slip-rates constrained by both cosmogenic and radiocarbon dating on these faults. Based upon the agreement of rates determined by radiocarbon and cosmogenic dating, the overall linearity of offset versus age correlations, and on the plateau-wide correlation of landscape evolution and climate history, the disparity between geomorphic and geodetic slip-rate determinations is unlikely to be due to the effects of surface erosion on the cosmogenic age determinations. Similarly, based upon the consistency of slip-rates over various observation intervals, secular variations in slip-rate appear to persist no longer than 2000 years and are unlikely to provide reconciliation. Conversely, geodetic and geomorphic slip-rate estimates on the Kunlun fault, which does not have significant splays or associated thrust faults, are in good agreement, indicating that there is no fundamental reason why these complementary geodetic and geomorphic methods should disagree. Similarly, the geodetic and geomorphic estimates of shortening rates across the northeastern edge of the plateau are in reasonable agreement, and the geomorphic rates on individual thrust faults demonstrate a significant eastward decrease in the shortening rate. This rate decrease is consistent with the transfer of slip from the Altyn Tagh Fault (ATF) to genetically-related thrust mountain building at its terminus. Rates on the ATF suggest a similar decrease in rate, but the current data set is too small to be definitive. Overall, the high, late Pleistocene-Holocene, geomorphic slip velocities on the major strike-slip faults of Tibet, suggests that they absorb as much of India's convergence relative to Siberia as the Himalayan Main Frontal Thrust on the southern edge of the plateau.« less

Geodetic Strain Analysis Tool

NASA Technical Reports Server (NTRS)

Kedar, Sharon; Baxter, Sean C.; Parker, Jay W.; Webb, Frank H.; Owen, Susan E.; Sibthorpe, Anthony J.; Dong, Danan

2011-01-01

A geodetic software analysis tool enables the user to analyze 2D crustal strain from geodetic ground motion, and create models of crustal deformation using a graphical interface. Users can use any geodetic measurements of ground motion and derive the 2D crustal strain interactively. This software also provides a forward-modeling tool that calculates a geodetic velocity and strain field for a given fault model, and lets the user compare the modeled strain field with the strain field obtained from the user s data. Users may change parameters on-the-fly and obtain a real-time recalculation of the resulting strain field. Four data products are computed: maximum shear, dilatation, shear angle, and principal components. The current view and data dependencies are processed first. The remaining data products and views are then computed in a round-robin fashion to anticipate view changes. When an analysis or display parameter is changed, the affected data products and views are invalidated and progressively re-displayed as available. This software is designed to facilitate the derivation of the strain fields from the GPS and strain meter data that sample it to facilitate the understanding of the strengths and weaknesses of the strain field derivation from continuous GPS (CGPS) and other geodetic data from a variety of tectonic settings, to converge on the "best practices" strain derivation strategy for the Solid Earth Science ESDR System (SESES) project given the CGPS station distribution in the western U.S., and to provide SESES users with a scientific and educational tool to explore the strain field on their own with user-defined parameters.

Propagation of uncertainty by Monte Carlo simulations in case of basic geodetic computations

NASA Astrophysics Data System (ADS)

Wyszkowska, Patrycja

2017-12-01

The determination of the accuracy of functions of measured or adjusted values may be a problem in geodetic computations. The general law of covariance propagation or in case of the uncorrelated observations the propagation of variance (or the Gaussian formula) are commonly used for that purpose. That approach is theoretically justified for the linear functions. In case of the non-linear functions, the first-order Taylor series expansion is usually used but that solution is affected by the expansion error. The aim of the study is to determine the applicability of the general variance propagation law in case of the non-linear functions used in basic geodetic computations. The paper presents errors which are a result of negligence of the higher-order expressions and it determines the range of such simplification. The basis of that analysis is the comparison of the results obtained by the law of propagation of variance and the probabilistic approach, namely Monte Carlo simulations. Both methods are used to determine the accuracy of the following geodetic computations: the Cartesian coordinates of unknown point in the three-point resection problem, azimuths and distances of the Cartesian coordinates, height differences in the trigonometric and the geometric levelling. These simulations and the analysis of the results confirm the possibility of applying the general law of variance propagation in basic geodetic computations even if the functions are non-linear. The only condition is the accuracy of observations, which cannot be too low. Generally, this is not a problem with using present geodetic instruments.

Multiteide Project: Multiparametric characterization of the activity of Teide-Pico Viejo volcanic system

NASA Astrophysics Data System (ADS)

Domínguez Cerdeña, Itahiza; Villasante-Marcos, Victor; Meletlidis, Stavros; Sainz-Maza, Sergio; Abella, Rafael; Torres, Pedro A.; Sánchez, Nieves; Luengo-Oroz, Natividad; José Blanco, María; García-Cañada, Laura; Pereda de Pablo, Jorge; Lamolda, Héctor; Moure, David; Del Fresno, Carmen; Finizola, Anthony; Felepto, Alicia

2017-04-01

Teide-Pico Viejo complex stands for one of the major natural volcanic hazards in the Canary Islands, due to the expected types of eruptions in the area and the high number of inhabitants in Tenerife Island. Therefore, it is necessary to have a volcanic alert system able to afford a precise assessment of the current state of the complex. For this purpose, the knowledge of the expected signals at each volcanic activity level is required. Moreover, the external effects that can affect the measurements shall be distinguished, external influences as the atmosphere are qualitatively known but have not been quantified yet. The objective of the project is to collect, analyze and jointly and continuously evaluate over time geophysical, geodetic, geochemical and meteorological data from the Teide-Pico Viejo complex and its surroundings. A continuous multiparametric network have been deployed in the area, which, together with the data provided by the Volcano Monitoring Network of the Instituto Geográfico Nacional (IGN) and data from other institutions will provide a comprehensive set of data with high resolution in both space and time. This multiparametric network includes a seismic array, two self-potential lines for continuous measurements, five magnetometers and two weather stations. The network will be complemented with 8 CGPS stations, one tiltmeter, 10 seismic stations, and four thermometric stations on the fumaroles of Teide volcano that IGN already manage in Tenerife. The data will be completed with the results from different repeated surveys of self potential, soil temperature and CO2 diffuse flux in several pre-established areas on top of Teide throughout the entire duration of project. During the project, new computation tools will be developed to study the correlation between the different parameters analyzed. The results obtained will characterize the possible seasonal fluctuations of each parameter and the variations related to meteorological phenomena. In addition, they will allow identifying the response of all the analyzed parameters to specific events that are traditionally studied with a single technique, such as short episodes of tremor (sporadically registered in Teide-Pico Viejo surroundings) or changes in activity of the hydrothermal system of the volcanic complex. We present here the first multiparametric results obtained from the project, including locations with the seismic array, CO2 and temperature maps of Teide fumaroles zones and magnetometric measurements.

Fixed point theorems of GPS carrier phase ambiguity resolution and their application to massive network processing: Ambizap

NASA Astrophysics Data System (ADS)

Blewitt, Geoffrey

2008-12-01

Precise point positioning (PPP) has become popular for Global Positioning System (GPS) geodetic network analysis because for n stations, PPP has O(n) processing time, yet solutions closely approximate those of O(n3) full network analysis. Subsequent carrier phase ambiguity resolution (AR) further improves PPP precision and accuracy; however, full-network bootstrapping AR algorithms are O(n4), limiting single network solutions to n < 100. In this contribution, fixed point theorems of AR are derived and then used to develop "Ambizap," an O(n) algorithm designed to give results that closely approximate full network AR. Ambizap has been tested to n ≈ 2800 and proves to be O(n) in this range, adding only ˜50% to PPP processing time. Tests show that a 98-station network is resolved on a 3-GHz CPU in 7 min, versus 22 h using O(n4) AR methods. Ambizap features a novel network adjustment filter, producing solutions that precisely match O(n4) full network analysis. The resulting coordinates agree to ≪1 mm with current AR methods, much smaller than the ˜3-mm RMS precision of PPP alone. A 2000-station global network can be ambiguity resolved in ˜2.5 h. Together with PPP, Ambizap enables rapid, multiple reanalysis of large networks (e.g., ˜1000-station EarthScope Plate Boundary Observatory) and facilitates the addition of extra stations to an existing network solution without need to reprocess all data. To meet future needs, PPP plus Ambizap is designed to handle ˜10,000 stations per day on a 3-GHz dual-CPU desktop PC.

Active Tectonics Around Pisagua, Northern Chile Gap: Seismological and Neotectonic Approaches

NASA Astrophysics Data System (ADS)

Comte, D.; Carrizo, D.; Peyrat, S.

2013-12-01

Northern Chile is a recognized mature seismic gap that is reaching the end of its megathrust cycle. Deformation associated with the convergence between the Nazca and the South American Plates is mainly absorbed along the interplate contact, but also partially accommodated along the upper plate. Even though distribution of the active deformation along this plate has been documented mainly in the backarc region, Late Cenozoic structures have been recognized along the forearc suggesting that some part of this deformation is also accommodated along the coastal region. Recent paleoseismological studies suggest that some of these structures are tectonically active and some could be potentially active, capable to generate shallow intraplate earthquakes (Mw˜7). However, seismological and geodetical evidences of the fault activation mechanisms are poorly documented, and the activation process remain not elucidate. Currently, Northern Chile seismic gap is monitored by regional seismic networks and partially studied by temporary local seismological experiments. Results of these studies suggest the presence of shallow seismicity along the forearc, but the relationships between upper plate faults and the seismicity has not been yet explored. We perform a detailed seismotectonic analysis of the subduction-forearc system in the central part of the Northern Chile seismic gap to establish relationships between the plate contact deformation and the upper plate faults. We present preliminary results of data recorded by a dense seismic network (three components continuous recording) deployed around Pisagua, between the coastline and the Central Depression, during several months. Pisagua region was chosen because the forearc faults exhibit an extraordinary well-preserved morphotectonic expression, and the upper part of the seismogenic interplate contact shows abundant continental intraplate seismicity that could be associated with the faults systems. The data recorded in this area allow us to better constrain the 3D geometry of faults related to plate contact using morphotectonis fault signature, well-located shallow seismicity and passive tomography. By this way, the architecture of the major forearc faults in the study area is determined for the first time using geological and geophysical approaches. Through this work, we contribute to better understand the physical relations between dynamics of the plate contact and the coastal fault activation.