Science.gov

Sample records for active infrared thermography

  1. Inspection of reinforcement concrete structures with active infrared thermography

    NASA Astrophysics Data System (ADS)

    Szymanik, Barbara; Chady, Tomasz; Frankowski, Paweł

    2017-02-01

    In this article the reinforced concrete non-destructive evaluation using active thermography is discussed. There are several aspects of possible non-destructive testing of mentioned structures. One of them is the detection and assessment of the reinforcement itself. In case of active thermography, the external energy source has to be used to induce the thermal response of the inspected specimen. Here, authors propose two different techniques: microwave heating and induction heating. In this article authors will present several experimental results which will allow to compare mentioned two techniques of heating. suitability of each one to assess the reinforced concrete by using the active thermography will be discussed.

  2. Infrared micro-thermography of an actively heated preconcentrator device

    NASA Astrophysics Data System (ADS)

    Furstenberg, Robert; Kendziora, C. A.; Stepnowski, Stanley V.; Mott, David R.; McGill, R. Andrew

    2008-03-01

    We report infrared micro-thermography measurements and analysis of static and transient temperature maps of an actively heated micro-fabricated preconcentrator device that incorporates a dual serpentine platinum heater trace deposited on a perforated polyimide membrane and suspended over a silicon frame. The sorbent coated perforated membrane is used to collect vapors and gases that flow through the preconcentrator. After heating, a concentrated pulse of analyte is released into the detector. Due to its small thermal mass, precise thermal management of the preconcentrator is critical to its performance. The sizes of features, the semi-transparent membrane, the need to flow air through the device, and changes in surface emissivity on a micron scale present many challenges for traditional infrared micro-thermography. We report an improved experimental test-bed. The hardware incorporates a custom-designed miniature calibration oven which, in conjunction with spatial filtering and a simple calibration algorithm, allows accurate temperature maps to be obtained. The test-bed incorporates a micro-bolometer array as the infrared imager. Instrumentation design, calibration and image processing algorithms are discussed and analyzed. The procedure does not require prior knowledge of the emissivity. We show that relatively inexpensive uncooled bolometers arrays can be used in certain radiometric applications. Heating profiles were examined with both uniform and non-uniform air flow through the device. The conclusions from this study provide critical information for optimal integration of the preconcentrator within a detection system, and in the design of the heater trace layout to achieve a more even temperature distribution across the device.

  3. Carbon fiber composites inspection and defect characterization using active infrared thermography: numerical simulations and experimental results.

    PubMed

    Fernandes, Henrique; Zhang, Hai; Figueiredo, Alisson; Ibarra-Castanedo, Clemente; Guimarares, Gilmar; Maldague, Xavier

    2016-12-01

    Composite materials are widely used in the aeronautic industry. One of the reasons is because they have strength and stiffness comparable to metals, with the added advantage of significant weight reduction. Infrared thermography (IT) is a safe nondestructive testing technique that has a fast inspection rate. In active IT, an external heat source is used to stimulate the material being inspected in order to generate a thermal contrast between the feature of interest and the background. In this paper, carbon-fiber-reinforced polymers are inspected using IT. More specifically, carbon/PEEK (polyether ether ketone) laminates with square Kapton inserts of different sizes and at different depths are tested with three different IT techniques: pulsed thermography, vibrothermography, and line scan thermography. The finite element method is used to simulate the pulsed thermography experiment. Numerical results displayed a very good agreement with experimental results.

  4. Non-destructive Testing of Forged Metallic Materials by Active Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Maillard, S.; Cadith, J.; Bouteille, P.; Legros, G.; Bodnar, J. L.; Detalle, V.

    2012-11-01

    Nowadays, infrared thermography is considered as the reference method in many applications such as safety, the inspection of electric installations, or the inspection of buildings' heat insulation. In recent years, the evolution of both material and data-processing tools also allows the development of thermography as a real non-destructive testing method. Thus, by subjecting the element to be inspected to an external excitation and by analyzing the propagation of heat in the examined zone, it is possible to highlight surface or subsurface defects such as cracks, delaminations, or corrosion. One speaks then about active infrared thermography. In this study, some results obtained during the collective studies carried out by CETIM and the University of Reims for the forging industry are presented. Various experimental possibilities offered by active thermography are presented and the interest in this method in comparison with the traditional non-destructive testing methods (penetrant testing and magnetic particle inspection) is discussed. For example, comparative results on a forged cracked hub, a steering joint, and a threaded rod are presented. They highlight the interest of infrared thermography stimulated by induction for forged parts.

  5. Nondestructive test of brazed cooling tubes of prototype bolometer camera housing using active infrared thermography.

    PubMed

    Tahiliani, Kumudni; Pandya, Santosh P; Pandya, Shwetang; Jha, Ratneshwar; Govindarajan, J

    2011-01-01

    The active infrared thermography technique is used for assessing the brazing quality of an actively cooled bolometer camera housing developed for steady state superconducting tokamak. The housing is a circular pipe, which has circular tubes vacuum brazed on the periphery. A unique method was adopted to monitor the temperature distribution on the internal surface of the pipe. A stainless steel mirror was placed inside the pipe and the reflected IR radiations were viewed using an IR camera. The heat stimulus was given by passing hot water through the tubes and the temperature distribution was monitored during the transient phase. The thermographs showed a significant nonuniformity in the brazing with a contact area of around 51%. The thermography results were compared with the x-ray radiographs and a good match between the two was observed. Benefits of thermography over x-ray radiography testing are emphasized.

  6. Active and passive infrared thermography applied to the detection and characterization of hidden defects in structure

    NASA Astrophysics Data System (ADS)

    Dumoulin, Jean

    2013-04-01

    Infrared thermography for Non Destructive Testing (NDT) has encountered a wide spreading this last 2 decades, in particular thanks to emergence on the market of low cost uncooled infrared camera. So, infrared thermography is not anymore a measurement technique limited to laboratory application. It has been more and more involved in civil engineering and cultural heritage applications, but also in many other domains, as indicated by numerous papers in the literature. Nevertheless, laboratory, measurements are done as much as possible in quite ideal conditions (good atmosphere conditions, known properties of materials, etc.), while measurement on real site requires to consider the influence of not controlled environmental parameters and additional unknown thermal properties. So, dedicated protocol and additional sensors are required for measurement data correction. Furthermore, thermal excitation is required to enhance the signature of defects in materials. Post-processing of data requires to take into account the protocol used for the thermal excitation and sometimes its nature to avoid false detection. This analysis step is based on signal and image processing tool and allows to carry out the detection. Characterization of anomalies detected at the previous step can be done by additional signal processing in particular for manufactured objects. The use of thermal modelling and inverse method allows to determine properties of the defective area. The present paper will first address a review of some protocols currently in use for field measurement with passive and/or active infrared measurements. Illustrations in various experiments carried out on civil engineering structure will be shown and discussed. In a second part, different post-processing approaches will be presented and discussed. In particular, a review of the most standard processing methods like Fast Fourier Analysis, Principal Components Analysis, Polynomial Decomposition, defect characterization using

  7. Non Destructive Testing by active infrared thermography coupled with shearography under same optical heat excitation

    NASA Astrophysics Data System (ADS)

    Theroux, Louis-Daniel; Dumoulin, Jean; Maldague, Xavier

    2014-05-01

    As infrastructures are aging, the evaluation of their health is becoming crucial. To do so, numerous Non Destructive Testing (NDT) methods are available. Among them, thermal shearography and active infrared thermography represent two full field and contactless methods for surface inspection. The synchronized use of both methods presents multiples advantages. Most importantly, both NDT are based on different material properties. Thermography depend on the thermal properties and shearography on the mechanical properties. The cross-correlation of both methods result in a more accurate and exact detection of the defects. For real site application, the simultaneous use of both methods is simplified due to the fact that the excitation method (thermal) is the same. Active infrared thermography is the measure of the temperature by an infrared camera of a surface subjected to heat flux. Observation of the variation of temperature in function of time reveal the presence of defects. On the other hand, shearography is a measure of out-of-plane surface displacement. This displacement is caused by the application of a strain on the surface which (in our case) take the form of a temperature gradient inducing a thermal stress To measure the resulting out-of-plane displacement, shearography exploit the relation between the phase difference and the optical path length. The phase difference is measured by the observation of the interference between two coherent light beam projected on the surface. This interference is due to change in optical path length as the surface is deformed [1]. A series of experimentation have been conducted in laboratory with various sample of concrete reinforced with CFRP materials. Results obtained reveal that with both methods it was possible to detect defects in the gluing. An infrared lamp radiating was used as the active heat source. This is necessary if measurements with shearography are to be made during the heating process. A heating lamp in the

  8. Veterinary applications of infrared thermography.

    PubMed

    Rekant, Steven I; Lyons, Mark A; Pacheco, Juan M; Arzt, Jonathan; Rodriguez, Luis L

    2016-01-01

    Abnormal body temperature is a major indicator of disease; infrared thermography (IRT) can assess changes in body surface temperature quickly and remotely. This technology can be applied to a myriad of diseases of various etiologies across a wide range of host species in veterinary medicine. It is used to monitor the physiologic status of individual animals, such as measuring feed efficiency or diagnosing pregnancy. Infrared thermography has applications in the assessment of animal welfare, and has been used to detect soring in horses and monitor stress responses. This review addresses the variety of uses for IRT in veterinary medicine, including disease detection, physiologic monitoring, welfare assessment, and potential future applications.

  9. Detection and characterisation of delamination in PV modules by active infrared thermography

    NASA Astrophysics Data System (ADS)

    Sinha, A.; Sastry, O. S.; Gupta, R.

    2016-01-01

    The paper presents a fast and efficient method for the detection and characterisation of delamination in photovoltaic (PV) modules by using active infrared thermography approach. A discrete part of PV module was irradiated by step heating and its thermal image sequence was used to detect and analyse delamination. Different types of heating source for thermal excitation for this application have been studied. An electro-thermal model was developed to simulate the active thermography approach for the characterisation of delamination in PV module by equivalent resistance-capacitance (RC) network using a circuit simulator. This simulation approach was used to estimate the extent of delamination in the module and to determine the optimum parameters for the characterisation of delamination. Different applications based on front and backsides of heating the module were also proposed in this paper. The proposed method has the potential to be employed for the quality check of PV modules during inline production as well as for the predictive maintenance of outdoor PV plants.

  10. Veterinary applications of infrared thermography

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Abnormal temperature is a major indicator of disease; infrared thermography (IRT) can assess changes in surface temperature quickly and remotely. This technology can be applied to myriad diseases in veterinary medicine, ranging across host species and disease etiologies. It can also be used to deter...

  11. The use of infrared thermography to detect the skin temperature response to physical activity

    NASA Astrophysics Data System (ADS)

    Tanda, G.

    2015-11-01

    Physical activity has a noticeable effect on skin blood flow and temperature. The thermal regulatory and hemodynamic processes during physical activity are controlled by two conflicting mechanisms: the skin vasoconstriction induced by the blood flow demand to active muscles and the skin vasodilation required by thermoregulation to increase warm blood flow and heat conduction to the skin. The time-evolution of skin temperature during exercise can give useful information about the adaptation of the subject as a function of specific type, intensity and duration of exercise. In this paper, infrared thermography is used to investigate the thermal response of skin temperature during running exercise on treadmill for a group of seven healthy and trained runners. Two different treadmill exercises are considered: a graded load exercise and a constant load exercise; for both exercises the duration was 30 minutes. Within the limits due to the relatively small size of the sample group, results typically indicate a fall in skin temperature during the initial stage of running exercise. As the exercise progresses, the dynamics of the skin temperature response depends on the type of exercise (graded versus constant load) and probably on the level of training of the subject.

  12. Airborne thermography or infrared remote sensing.

    PubMed

    Goillot, C C

    1975-01-01

    Airborne thermography is part of the more general remote sensing activity. The instruments suitable for image display are infrared line scanners. A great deal of interest has developed during the past 10 years in airborne thermal remote sensing and many applications are in progress. Infrared scanners on board a satellite are used for observation of cloud cover; airborne infrared scanners are used for forest fire detection, heat budget of soils, detecting insect attack, diseases, air pollution damage, water stress, salinity stress on vegetation, only to cite some main applications relevant to agronomy. Using this system it has become possible to get a 'picture' of our thermal environment.

  13. Detection of seal contamination in heat-sealed food packaging based on active infrared thermography

    NASA Astrophysics Data System (ADS)

    D'huys, Karlien; Saeys, Wouter; De Ketelaere, Bart

    2015-05-01

    In the food industry packaging is often applied to protect the product from the environment, assuring quality and safety throughout shelf life if properly performed. Packaging quality depends on the material used and the closure (seal). The material is selected based on the specific needs of the food product to be wrapped. However, proper closure of the package is often harder to achieve. One problem possibly jeopardizing seal quality is the presence of food particles between the seal. Seal contamination can cause a decreased seal strength and thus an increased packaging failure risk. It can also trigger the formation of microchannels through which air and microorganisms can enter and spoil the enclosed food. Therefore, early detection and removal of seal-contaminated packages from the production chain is essential. In this work, a pulsed-type active thermography method using the heat of the sealing bars as an excitation source was studied for detecting seal contamination. The cooling profile of contaminated seals was recorded. The detection performance of four processing methods (based on a single frame, a fit of the cooling profile, pulsed phase thermography and a matched filter) was compared. High resolution digital images served as a reference to quantify contamination. The lowest detection limit (equivalent diameter of 0.63 mm) and the lowest processing time (0.42 s per sample) were obtained for the method based on a single frame. Presumably, practical limitations in the recording stage prevented the added value of active thermography to be fully reflected in this application.

  14. Thermography.

    ERIC Educational Resources Information Center

    Cage, Bob N.

    1984-01-01

    Thermography, a diagnostic tool that combines photography and infrared sensing, permits direct measurement of apparent surface temperatures. Building energy losses can be detected and correction measures planned. Criteria for the use of thermography are provided. (MLF)

  15. Narrative review: Diabetic foot and infrared thermography

    NASA Astrophysics Data System (ADS)

    Hernandez-Contreras, D.; Peregrina-Barreto, H.; Rangel-Magdaleno, J.; Gonzalez-Bernal, J.

    2016-09-01

    Diabetic foot is one of the major complications experienced by diabetic patients. An early identification and appropriate treatment of diabetic foot problems can prevent devastating consequences such as limb amputation. Several studies have demonstrated that temperature variations in the plantar region can be related to diabetic foot problems. Infrared thermography has been successfully used to detect complication related to diabetic foot, mainly because it is presented as a rapid, non-contact and non-invasive technique to visualize the temperature distribution of the feet. In this review, an overview of studies that relate foot temperature with diabetic foot problems through infrared thermography is presented. Through this research, it can be appreciated the potential of infrared thermography and the benefits that this technique present in this application. This paper also presents the different methods for thermogram analysis and the advantages and disadvantages of each one, being the asymmetric analysis the method most used so far.

  16. Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors

    PubMed Central

    Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

    2016-01-01

    The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented. PMID:26891305

  17. Detection and Inspection of Steel Bars in Reinforced Concrete Structures Using Active Infrared Thermography with Microwave Excitation and Eddy Current Sensors.

    PubMed

    Szymanik, Barbara; Frankowski, Paweł Karol; Chady, Tomasz; John Chelliah, Cyril Robinson Azariah

    2016-02-16

    The purpose of this paper is to present a multi-sensor approach to the detection and inspection of steel bars in reinforced concrete structures. In connection with our past experience related to non-destructive testing of different materials, we propose using two potentially effective methods: active infrared thermography with microwave excitation and the eddy current technique. In this article active infrared thermography with microwave excitation is analyzed both by numerical modeling and experiments. This method, based on thermal imaging, due to its characteriatics should be considered as a preliminary method for the assessment of relatively shallowly located steel bar reinforcements. The eddy current technique, on the other hand, allows for more detailed evaluation and detection of deeply located rebars. In this paper a series of measurement results, together with the initial identification of certain features of steel reinforcement bars will be presented.

  18. Infrared thermography for indirect assessment of activation of brown adipose tissue in lean and obese male subjects.

    PubMed

    El Hadi, Hamza; Frascati, Andrea; Granzotto, Marnie; Silvestrin, Valentina; Ferlini, Elisabetta; Vettor, Roberto; Rossato, Marco

    2016-12-01

    Brown adipose tissue (BAT) plays a key role in adaptive thermogenesis in mammals, and it has recently been considered as an attractive therapeutic target for tackling human obesity by increasing energy expenditure. Thermal imaging using infrared thermography (IRT) has emerged as a potential safe, rapid and inexpensive technique for detecting BAT in humans. However, little attention has been given to the reliability of this method in obese subjects. To this end, we evaluated the capacity of IRT to detect activated supraclavicular (SCV) BAT in 14 lean and 16 mildly obese young adults after acute cold exposure. Using IRT we measured the temperature of the skin overlying the SCV and sternal areas at baseline and after acute cold stimulation. Additionally, energy expenditure was measured by indirect calorimetry and body composition was estimated using bioelectrical impedance analysis. Energy expenditure and SCV skin temperature significantly increased in lean subjects upon cold exposure, while no significant changes were detected in the obese group. Furthermore, cold-induced variations in SCV skin temperature of obese subjects showed a negative correlation with body mass index. This study suggests that in lean individuals BAT is a rapidly activated thermogenic tissue possibly involved in the regulation of energy balance, and can be indirectly assessed using IRT. In obese subjects, BAT seems less prone to be activated by cold exposure, with the degree of adiposity representing a limiting factor for the indirect detection of BAT activation by measuring the skin temperature overlying BAT.

  19. A new method of infrared thermography for quantification of brown adipose tissue activation in healthy adults (TACTICAL): a randomized trial.

    PubMed

    Ang, Qi Yan; Goh, Hui Jen; Cao, Yanpeng; Li, Yiqun; Chan, Siew-Pang; Swain, Judith L; Henry, Christiani Jeyakumar; Leow, Melvin Khee-Shing

    2017-05-01

    The ability to alter the amount and activity of brown adipose tissue (BAT) in human adults is a potential strategy to manage obesity and related metabolic disorders associated with food, drug, and environmental stimuli with BAT activating/recruiting capacity. Infrared thermography (IRT) provides a non-invasive and inexpensive alternative to the current methods (e.g. (18)F-FDG PET) used to assess BAT. We have quantified BAT activation in the cervical-supraclavicular (C-SCV) region using IRT video imaging and a novel image computational algorithm by studying C-SCV heat production in healthy young men after cold stimulation and the ingestion of capsinoids in a prospective double-blind placebo-controlled randomized trial. Subjects were divided into low-BAT and high-BAT groups based on changes in IR emissions in the C-SCV region induced by cold. The high-BAT group showed significant increases in energy expenditure, fat oxidation, and heat output in the C-SCV region post-capsinoid ingestion compared to post-placebo ingestion, but the low-BAT group did not. Based on these results, we conclude that IRT is a promising tool for quantifying BAT activity.

  20. Bridge concrete deteriorating diagnosis by infrared thermography

    NASA Astrophysics Data System (ADS)

    Shibata, Hiroki; Fukuyama, Nobuhiro; Sakuma, Joji; Mochizuki, Jun; Kimura, Yukinori

    2006-04-01

    Bridge is indispensable as social overhead capital. In the past, concrete construction was believed to be semi-permanent. Actually, however, concrete is deteriorated by various factors including seawater damage, annual temperature change, etc. Therefore, it is now obvious that maintenance and management are essential to keep performance of the bridge. In Japan, we had many reports of using infrared thermography for diagnosis of building, mainly for delamination of tile and mortar used for surface of the building for more than 10 years. In recent years, infrared thermogrephy is more actively used for delamination of surface of the bridge. Passive method is usually used for open-air concrete structure diagnosis, which utilizes intraday environmental temperature change and/or radiation energy emitted from the sun which create delta-T of delamination portion of the concrete structure. It is very important to take thermal image at right conditions. Otherwise, you may easily fall onto false diagnosis. In our presentation, many case examples and study of thermal data will be shown, which are taken at the right condition.

  1. Infrared thermography in the architectural field.

    PubMed

    Meola, Carosena

    2013-01-01

    Infrared thermography is becoming ever more popular in civil engineering/architecture mainly due to its noncontact character which includes two great advantages. On one side, it prevents the object, under inspection, from any alteration and this is worthwhile especially in the presence of precious works of art. On the other side, the personnel operate in a remote manner far away from any hazard and this complies well with safety at work regulations. What is more, it offers the possibility to quickly inspect large surfaces such as the entire facade of a building. This paper would be an overview of the use of infrared thermography in the architectural and civil engineering field. First, some basic testing procedures are described, and then some key examples are presented owing to both laboratory tests and applications in situ spanning from civil habitations to works of art and archaeological sites.

  2. Infrared Thermography in the Architectural Field

    PubMed Central

    2013-01-01

    Infrared thermography is becoming ever more popular in civil engineering/architecture mainly due to its noncontact character which includes two great advantages. On one side, it prevents the object, under inspection, from any alteration and this is worthwhile especially in the presence of precious works of art. On the other side, the personnel operate in a remote manner far away from any hazard and this complies well with safety at work regulations. What is more, it offers the possibility to quickly inspect large surfaces such as the entire facade of a building. This paper would be an overview of the use of infrared thermography in the architectural and civil engineering field. First, some basic testing procedures are described, and then some key examples are presented owing to both laboratory tests and applications in situ spanning from civil habitations to works of art and archaeological sites. PMID:24319358

  3. Infrared Thermography of Thermomechanical Couplings in Solids

    NASA Astrophysics Data System (ADS)

    Luong, M. P.; Parganin, D.; Loizeau, J.

    The present paper aims to illustrate three advantages of infrared thermography as a non destructive, real-time and non-contact technique to mechanically characterise solid materials. It permits observation of the macrostructural aspects of. thermoplasticity describing damage and failure processes in diverse and various engineering materials and their components subjected to monotonous, cyclic or vibratory loading. It usefully suggests the definition of a threshold of acceptable damage TAD for materials related to sport equipment such as leather shoe, leather-like composites or sail synthetics. Particularly in case of metallic products or automotive components subjected to fatigue loading, this newly proposed method could evaluate in a non-destructive manner the fatigue limit FL in a very short time compared to traditional fatigue testing techniques that are much more time-consuming and excessively expensive. In addition owing to the thermomechanical coupling, infrared thermography readily describes the damage location, the dissipative regime and the evolution of structural failure.

  4. Thermal signature analysis of human face during jogging activity using infrared thermography technique

    NASA Astrophysics Data System (ADS)

    Budiarti, Putria W.; Kusumawardhani, Apriani; Setijono, Heru

    2016-11-01

    Thermal imaging has been widely used for many applications. Thermal camera is used to measure object's temperature above absolute temperature of 0 Kelvin using infrared radiation emitted by the object. Thermal imaging is color mapping taken using false color that represents temperature. Human body is one of the objects that emits infrared radiation. Human infrared radiations vary according to the activity that is being done. Physical activities such as jogging is among ones that is commonly done. Therefore this experiment will investigate the thermal signature profile of jogging activity in human body, especially in the face parts. The results show that the significant increase is found in periorbital area that is near eyes and forehand by the number of 7.5%. Graphical temperature distributions show that all region, eyes, nose, cheeks, and chin at the temperature of 28.5 - 30.2°C the pixel area tends to be constant since it is the surrounding temperature. At the temperature of 30.2 - 34.7°C the pixel area tends to increase, while at the temperature of 34.7 - 37.1°C the pixel area tends to decrease because pixels at temperature of 34.7 - 37.1°C after jogging activity change into temperature of 30.2 - 34.7°C so that the pixel area increases. The trendline of jogging activity during 10 minutes period also shows the increasing of temperature. The results of each person also show variations due to physiological nature of each person, such as sweat production during physical activities.

  5. Infrared thermography for CFRP inspection: computational model and experimental results

    NASA Astrophysics Data System (ADS)

    Fernandes, Henrique C.; Zhang, Hai; Morioka, Karen; Ibarra-Castanedo, Clemente; López, Fernando; Maldague, Xavier P. V.; Tarpani, José R.

    2016-05-01

    Infrared Thermography (IRT) is a well-known Non-destructive Testing (NDT) technique. In the last decades, it has been widely applied in several fields including inspection of composite materials (CM), specially the fiber-reinforced polymer matrix ones. Consequently, it is important to develop and improve efficient NDT techniques to inspect and assess the quality of CM parts in order to warranty airworthiness and, at the same time, reduce costs of airline companies. In this paper, active IRT is used to inspect carbon fiber-reinforced polymer (CFRP) at laminate with artificial inserts (built-in sample) placed on different layers prior to the manufacture. Two optical active IRT are used. The first is pulsed thermography (PT) which is the most widely utilized IRT technique. The second is a line-scan thermography (LST) technique: a dynamic technique, which can be employed for the inspection of materials by heating a component, line-by-line, while acquiring a series of thermograms with an infrared camera. It is especially suitable for inspection of large parts as well as complex shaped parts. A computational model developed using COMSOL Multiphysics® was used in order to simulate the inspections. Sequences obtained from PT and LST were processed using principal component thermography (PCT) for comparison. Results showed that it is possible to detect insertions of different sizes at different depths using both PT and LST IRT techniques.

  6. Infrared Thermography User Group (IRUG) 2003 Meeting Proceedings

    SciTech Connect

    2003-10-01

    Infrared thermography is a key component of predictive maintenance programs for fossil and nuclear utilities. EPRI's Technology for Equipment Assessment and Maintenance (TEAM) group and their Maintenance Management & Technology (MM&T) program supported the 13th Infrared Thermography Users' Group (IRUG) meeting, which was hosted and also supported by Progress Energy.

  7. Lasers and infrared thermography: advantageous cooperation.

    PubMed

    Vainer, Boris G

    2016-12-01

    In a brief review, the beneficial outcomes that have arisen from simultaneous use of laser- and infrared thermography (IRT)-based techniques are demonstrated. The most recent literary and original experimental results collected from different research and practical areas are presented. It is shown that modern IRT acts as an indispensable laser partner in various biomedical and many other applications and technologies. And vice versa, the laser-based methods and techniques often serve as an appropriate research instrument enriching IRT measurement data with independently obtained information.

  8. Shuttle Entry Imaging Using Infrared Thermography

    NASA Technical Reports Server (NTRS)

    Horvath, Thomas; Berry, Scott; Alter, Stephen; Blanchard, Robert; Schwartz, Richard; Ross, Martin; Tack, Steve

    2007-01-01

    During the Columbia Accident Investigation, imaging teams supporting debris shedding analysis were hampered by poor entry image quality and the general lack of information on optical signatures associated with a nominal Shuttle entry. After the accident, recommendations were made to NASA management to develop and maintain a state-of-the-art imagery database for Shuttle engineering performance assessments and to improve entry imaging capability to support anomaly and contingency analysis during a mission. As a result, the Space Shuttle Program sponsored an observation campaign to qualitatively characterize a nominal Shuttle entry over the widest possible Mach number range. The initial objectives focused on an assessment of capability to identify/resolve debris liberated from the Shuttle during entry, characterization of potential anomalous events associated with RCS jet firings and unusual phenomenon associated with the plasma trail. The aeroheating technical community viewed the Space Shuttle Program sponsored activity as an opportunity to influence the observation objectives and incrementally demonstrate key elements of a quantitative spatially resolved temperature measurement capability over a series of flights. One long-term desire of the Shuttle engineering community is to calibrate boundary layer transition prediction methodologies that are presently part of the Shuttle damage assessment process using flight data provided by a controlled Shuttle flight experiment. Quantitative global imaging may offer a complementary method of data collection to more traditional methods such as surface thermocouples. This paper reviews the process used by the engineering community to influence data collection methods and analysis of global infrared images of the Shuttle obtained during hypersonic entry. Emphasis is placed upon airborne imaging assets sponsored by the Shuttle program during Return to Flight. Visual and IR entry imagery were obtained with available airborne

  9. Infrared Thermography for Temperature Measurement and Non-Destructive Testing

    PubMed Central

    Usamentiaga, Rubèn; Venegas, Pablo; Guerediaga, Jon; Vega, Laura; Molleda, Julio; Bulnes, Francisco G.

    2014-01-01

    The intensity of the infrared radiation emitted by objects is mainly a function of their temperature. In infrared thermography, this feature is used for multiple purposes: as a health indicator in medical applications, as a sign of malfunction in mechanical and electrical maintenance or as an indicator of heat loss in buildings. This paper presents a review of infrared thermography especially focused on two applications: temperature measurement and non-destructive testing, two of the main fields where infrared thermography-based sensors are used. A general introduction to infrared thermography and the common procedures for temperature measurement and non-destructive testing are presented. Furthermore, developments in these fields and recent advances are reviewed. PMID:25014096

  10. Infrared thermography for temperature measurement and non-destructive testing.

    PubMed

    Usamentiaga, Rubén; Venegas, Pablo; Guerediaga, Jon; Vega, Laura; Molleda, Julio; Bulnes, Francisco G

    2014-07-10

    The intensity of the infrared radiation emitted by objects is mainly a function of their temperature. In infrared thermography, this feature is used for multiple purposes: as a health indicator in medical applications, as a sign of malfunction in mechanical and electrical maintenance or as an indicator of heat loss in buildings. This paper presents a review of infrared thermography especially focused on two applications: temperature measurement and non-destructive testing, two of the main fields where infrared thermography-based sensors are used. A general introduction to infrared thermography and the common procedures for temperature measurement and non-destructive testing are presented. Furthermore, developments in these fields and recent advances are reviewed.

  11. Flash Infrared Thermography Contrast Data Analysis Technique

    NASA Technical Reports Server (NTRS)

    Koshti, Ajay

    2014-01-01

    This paper provides information on an IR Contrast technique that involves extracting normalized contrast versus time evolutions from the flash thermography inspection infrared video data. The analysis calculates thermal measurement features from the contrast evolution. In addition, simulation of the contrast evolution is achieved through calibration on measured contrast evolutions from many flat-bottom holes in the subject material. The measurement features and the contrast simulation are used to evaluate flash thermography data in order to characterize delamination-like anomalies. The thermal measurement features relate to the anomaly characteristics. The contrast evolution simulation is matched to the measured contrast evolution over an anomaly to provide an assessment of the anomaly depth and width which correspond to the depth and diameter of the equivalent flat-bottom hole (EFBH) similar to that used as input to the simulation. A similar analysis, in terms of diameter and depth of an equivalent uniform gap (EUG) providing a best match with the measured contrast evolution, is also provided. An edge detection technique called the half-max is used to measure width and length of the anomaly. Results of the half-max width and the EFBH/EUG diameter are compared to evaluate the anomaly. The information provided here is geared towards explaining the IR Contrast technique. Results from a limited amount of validation data on reinforced carbon-carbon (RCC) hardware are included in this paper.

  12. Subsurface defect detection in first layer of pavement structure and reinforced civil engineering structure by FRP bonding using active infrared thermography

    NASA Astrophysics Data System (ADS)

    Dumoulin, Jean; Ibos, Laurent

    2010-05-01

    In many countries road network ages while road traffic and maintenance costs increase. Nowadays, thousand and thousand kilometers of roads are each year submitted to surface distress survey. They generally lean on pavement surface imaging measurement techniques, mainly in the visible spectrum, coupled with visual inspection or image processing detection of emergent distresses. Nevertheless, optimisation of maintenance works and costs requires an early detection of defects within the pavement structure when they still are hidden from surface. Accordingly, alternative measurement techniques for pavement monitoring are currently under investigation (seismic methods, step frequency radar). On the other hand, strengthening or retrofitting of reinforced concrete structures by externally bonded Fiber Reinforced Polymer (FRP) systems is now a commonly accepted and widespread technique. However, the use of bonding techniques always implies following rigorous installing procedures. To ensure the durability and long-term performance of the FRP reinforcements, conformance checking through an in situ auscultation of the bonded FRP systems is then highly suitable. The quality-control program should involve a set of adequate inspections and tests. Visual inspection and acoustic sounding (hammer tap) are commonly used to detect delaminations (disbonds) but are unable to provide sufficient information about the depth (in case of multilayered composite) and width of debonded areas. Consequently, rapid and efficient inspection methods are also required. Among the non destructive methods under study, active infrared thermography was investigated both for pavement and civil engineering structures through experiments in laboratory and numerical simulations, because of its ability to be also used on field. Pulse Thermography (PT), Pulse Phase Thermography (PPT) and Principal Component Thermography (PCT) approaches have been tested onto pavement samples and CFRP bonding on concrete

  13. Convective heat transfer and infrared thermography.

    PubMed

    Carlomagno, Giovanni M; Astarita, Tommaso; Cardone, Gennaro

    2002-10-01

    Infrared (IR) thermography, because of its two-dimensional and non-intrusive nature, can be exploited in industrial applications as well as in research. This paper deals with measurement of convective heat transfer coefficients (h) in three complex fluid flow configurations that concern the main aspects of both internal and external cooling of turbine engine components: (1) flow in ribbed, or smooth, channels connected by a 180 degrees sharp turn, (2) a jet in cross-flow, and (3) a jet impinging on a wall. The aim of this study was to acquire detailed measurements of h distribution in complex flow configurations related to both internal and external cooling of turbine components. The heated thin foil technique, which involves the detection of surface temperature by means of an IR scanning radiometer, was exploited to measure h. Particle image velocimetry was also used in one of the configurations to precisely determine the velocity field.

  14. Automated Spot Weld Inspection using Infrared Thermography

    SciTech Connect

    Chen, Jian; Zhang, Wei; Yu, Zhenzhen; Feng, Zhili

    2012-01-01

    An automated non-contact and non-destructive resistance spot weld inspection system based on infrared (IR) thermography was developed for post-weld applications. During inspection, a weld coupon was heated up by an auxiliary induction heating device from one side of the weld, while the resulting thermal waves on the other side were observed by an IR camera. The IR images were analyzed to extract a thermal signature based on normalized heating time, which was then quantitatively correlated to the spot weld nugget size. The use of normalized instead of absolute IR intensity was found to be useful in minimizing the sensitivity to the unknown surface conditions and environment interference. Application of the IR-based inspection system to different advanced high strength steels, thickness gauges and coatings were discussed.

  15. INFRARED THERMOGRAPHY OF CUTANEOUS MELANOMA METASTASES

    PubMed Central

    Shada, Amber L.; Dengel, Lynn T.; Petroni, Gina R.; Smolkin, Mark E.; Acton, Scott; Slingluff, Craig L.

    2014-01-01

    Background Differentiating melanoma metastasis from benign cutaneous lesions currently requires biopsy or costly imaging, such as positron emission tomography scans. Melanoma metastases have been observed to be subjectively warmer than similarly appearing benign lesions. We hypothesized that infrared (IR) thermography would be sensitive and specific in differentiating palpable melanoma metastases from benign lesions. Materials and methods Seventy-four patients (36 females and 38 males) had 251 palpable lesions imaged for this pilot study. Diagnosis was determined using pathologic confirmation or clinical diagnosis. Lesions were divided into size strata for analysis: 0–5, >5–15, >15–30, and >30 mm. Images were scored on a scale from −1 (colder than the surrounding tissue) to +3 (significantly hotter than the surrounding tissue). Sensitivity and specificity were calculated for each stratum. Logistical challenges were scored. Results IR imaging was able to determine the malignancy of small (0–5 mm) lesions with a sensitivity of 39% and specificity of 100%. For lesions >5–15 mm, sensitivity was 58% and specificity 98%. For lesions >15–30 mm, sensitivity was 95% and specificity 100%, and for lesions >30 mm, sensitivity was 78% and specificity 89%. The positive predictive value was 88%–100% across all strata, and the negative predictive value was 95% for >15–30 mm lesions and 80% for >30 mm lesions. Conclusions Malignant lesions >15 mm were differentiated from benign lesions with excellent sensitivity and specificity. IR imaging was well tolerated and feasible in a clinic setting. This pilot study shows promise in the use of thermography for the diagnosis of malignant melanoma with further potential as a noninvasive tool to follow tumor responses to systemic therapies. PMID:23043862

  16. Medical applications of infrared thermography: A review

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Bagavathiappan, S.; Jayakumar, T.; Philip, John

    2012-07-01

    Abnormal body temperature is a natural indicator of illness. Infrared thermography (IRT) is a fast, passive, non-contact and non-invasive alternative to conventional clinical thermometers for monitoring body temperature. Besides, IRT can also map body surface temperature remotely. Last five decades witnessed a steady increase in the utility of thermal imaging cameras to obtain correlations between the thermal physiology and skin temperature. IRT has been successfully used in diagnosis of breast cancer, diabetes neuropathy and peripheral vascular disorders. It has also been used to detect problems associated with gynecology, kidney transplantation, dermatology, heart, neonatal physiology, fever screening and brain imaging. With the advent of modern infrared cameras, data acquisition and processing techniques, it is now possible to have real time high resolution thermographic images, which is likely to surge further research in this field. The present efforts are focused on automatic analysis of temperature distribution of regions of interest and their statistical analysis for detection of abnormalities. This critical review focuses on advances in the area of medical IRT. The basics of IRT, essential theoretical background, the procedures adopted for various measurements and applications of IRT in various medical fields are discussed in this review. Besides background information is provided for beginners for better understanding of the subject.

  17. Infrared thermography and overloaded neutral conductors

    NASA Astrophysics Data System (ADS)

    McComb, John; Niebla, Hector E.

    1999-03-01

    Present findings of two recent case studies. One involves transformer failures on three computer-stores within eight hours of their grand opening. The second discusses the findings during an infrared thermography-training course for electric utility engineers of a transformer vault serving an industrial customer. Both of these deal with overloaded neutral conductors. Historically, the average neutral conductor carried only the imbalance of the current between the phases of a three-phase system. This current was typically small in relation to the load being served. In fact, for economic reasons many neutrals were installed smaller than their associated phase conductors. Today however, certain types of loads (non-linear loads such as computers) and certain transformer connections (4 bushing single phase with a collector bus) cause the neutral to have up to three times as much amperage as the phase conductors. This paper will discuss the conditions under which such loading occurs and further investigate steps that can be taken/recommended should an infrared test indicate an overloaded neutral conductor.

  18. Infrared Thermography in High Level Waste

    SciTech Connect

    GLEATON, DAVIDT.

    2004-08-24

    The Savannah River Site is a Department of Energy, government-owned, company-operated industrial complex built in the 1950s to produce materials used in nuclear weapons. Five reactors were built to support the production of nuclear weapons material. Irradiated materials were moved from the reactors to one of the two chemical separation plants. In these facilities, known as ''canyons,'' the irradiated fuel and target assemblies were chemically processed to separate useful products from waste. Unfortunately, the by-product waste of nuclear material production was a highly radioactive liquid that had to be stored and maintained. In 1993 a strategy was developed to implement predictive maintenance technologies in the Liquid Waste Disposition Project Division responsible for processing the liquid waste. Responsibilities include the processing and treatment of 51 underground tanks designed to hold 750,000 to1,300,000 gallons of liquid waste and operation of a facility that vitrifies highly radioactive liquid waste into glass logs. Electrical and mechanical equipment monitored at these facilities is very similar to that found in non-nuclear industrial plants. Annual inspections are performed on electrical components, roof systems, and mechanical equipment. Troubleshooting and post installation and post-maintenance infrared inspections are performed as needed. In conclusion, regardless of the industry, the use of infrared thermography has proven to be an efficient and effective method of inspection to help improve plant safety and reliability through early detection of equipment problems.

  19. [Infrared thermography and electroneuromyography in occupational polyneuropathy diagnosis].

    PubMed

    Loginova, N N; Voitenkov, V B

    2013-01-01

    We have evaluated diagnostic value of the combination of infrared thermography and electromyography in professional polyneuropathy diagnosis. 20 patients with working-hand syndrome and 5 controls were enrolled. In 18 cases (90%) both methods were sensitive: on EMG CNV slowing and amplitudes drop were seen, as well as M-response shape changes, and thermography have detected focal hypothermia in hands in some cases and appearance of obscure hypothermia in others. Thus, both methods demonstrated good sensitivity. We recommend using thermography as a screening test and EMG as a following investigation.

  20. Membrane fouling characterization by infrared thermography

    NASA Astrophysics Data System (ADS)

    Ndukaife, Kennethrex O.; Ndukaife, Justus C.; Agwu Nnanna, A. G.

    2015-01-01

    An infrared thermography (IRT) technique for characterization of fouling on flat sheet membrane surface has been developed. In this work, an IR camera was used to measure surface temperature and emissivity of foulant on a membrane surface. Different fouling experiments were performed using different feed concentrations of aluminum oxide nanoparticle mixed with deionized water so as to investigate the effect of feed concentration on the degree of fouling and on the emissivity values measured on the membrane surfaces. Our findings revealed that the emissivity of the fouled membrane surface is contingent on the surface roughness as well as the material composition of the foulant. The technique was utilized to distinguish between foulants made of metallic materials from those that are non-metallic. This approach, which is simple to use and nondestructive represents an important addition to the toolset of fouling analysis techniques and would benefit a wide range of applications from observation of foulant structure to qualitative assessment of composition of foulant material.

  1. Is It Possible to Detect Activated Brown Adipose Tissue in Humans Using Single-Time-Point Infrared Thermography under Thermoneutral Conditions? Impact of BMI and Subcutaneous Adipose Tissue Thickness

    PubMed Central

    Gatidis, Sergios; Schmidt, Holger; Pfannenberg, Christina A.; Nikolaou, Konstantin; Schick, Fritz; Schwenzer, Nina F.

    2016-01-01

    Purpose To evaluate the feasibility to detect activated brown adipose tissue (BAT) using single-time-point infrared thermography of the supraclavicular skin region under thermoneutral conditions. To this end, infrared thermography was compared with 18-F-FDG PET, the current reference standard for the detection of activated BAT. Methods 120 patients were enrolled in this study. After exclusion of 18 patients, 102 patients (44 female, 58 male, mean age 58±17 years) were included for final analysis. All patients underwent a clinically indicated 18F-FDG-PET/CT examination. Immediately prior to tracer injection skin temperatures of the supraclavicular, presternal and jugular regions were measured using spatially resolved infrared thermography at room temperature. The presence of activated BAT was determined in PET by typical FDG uptake within the supraclavicular adipose tissue compartments. Local thickness of supraclavicular subcutaneous adipose tissue (SCAT) was measured on CT. Measured skin temperatures were statistically correlated with the presence of activated BAT and anthropometric data. Results Activated BAT was detected in 9 of 102 patients (8.8%). Local skin temperature of the supraclavicular region was significantly higher in individuals with active BAT compared to individuals without active BAT. However, after statistical correction for the influence of BMI, no predictive value of activated BAT on skin temperature of the supraclavicular region could be observed. Supraclavicular skin temperature was significantly negatively correlated with supraclavicular SCAT thickness. Conclusion We conclude that supraclavicular SCAT thickness influences supraclavicular skin temperature and thus makes a specific detection of activated BAT using single-time-point thermography difficult. Further studies are necessary to evaluate the possibility of BAT detection using alternative thermographic methods, e.g. dynamic thermography or MR-based thermometry taking into account BMI

  2. Infrared thermography in the restoration of cultural properties

    NASA Astrophysics Data System (ADS)

    Carlomagno, Giovanni M.; Carosena, Meola

    2001-03-01

    Some of the work carried out at DETEC on the use of infrared thermography in the architectural restoration field is examined. Three different techniques, pulse thermography (PT), modulated thermography (MT) and pulse phase thermography (PPT) are analyzed through the control of some art treasures such as mosaics and frescoes. In particular, the following artifacts are considered: mosaics covering some external walls of the building of the Faculty of Engineering of Naples, frescoes in the Duomo of Sarno, frescoes in the Cripta SS. Stefani in Vaste (Le), mosaics and frescoes in the Archeological Museum of Naples coming from Pompeii and Ruvo. It is found that the choice of the technique depends on the specific surface to be tested: if only qualitative information about detachments and cracks are needed the pulse thermography is sufficient; if the surface is not very sensitive to temperature rising, the pulse phase thermography can be applied which gives information about the location of the defected zone. If instead, the analysis regards rare art treasures, lockin thermography is the only response.

  3. Effect of perspiration on skin temperature measurements by infrared thermography and contact thermometry during aerobic cycling

    NASA Astrophysics Data System (ADS)

    Priego Quesada, Jose Ignacio; Martínez Guillamón, Natividad; Cibrián Ortiz de Anda, Rosa M.a.; Psikuta, Agnes; Annaheim, Simon; Rossi, René Michel; Corberán Salvador, José Miguel; Pérez-Soriano, Pedro; Salvador Palmer, Rosario

    2015-09-01

    The aim of the present study was to compare infrared thermography and thermal contact sensors for measuring skin temperature during cycling in a moderate environment. Fourteen cyclists performed a 45-min cycling test at 50% of peak power output. Skin temperatures were simultaneously recorded by infrared thermography and thermal contact sensors before and immediately after cycling activity as well as after 10 min cooling-down, representing different skin wetness and blood perfusion states. Additionally, surface temperature during well controlled dry and wet heat exchange (avoiding thermoregulatory responses) using a hot plate system was assessed by infrared thermography and thermal contact sensors. In human trials, the inter-method correlation coefficient was high when measured before cycling (r = 0.92) whereas it was reduced immediately after the cycling (r = 0.82) and after the cooling-down phase (r = 0.59). Immediately after cycling, infrared thermography provided lower temperature values than thermal contact sensors whereas it presented higher temperatures after the cooling-down phase. Comparable results as in human trials were observed for hot plate tests in dry and wet states. Results support the application of infrared thermography for measuring skin temperature in exercise scenarios where perspiration does not form a water film.

  4. Subsurface Defect Detection in FRP Composites Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Halabe, U. B.; Vasudevan, A.; GangaRao, H. V. S.; Klinkhachorn, P.; Lonkar, G.

    2005-04-01

    This paper demonstrates the use of digital infrared thermography to detect subsurface defects such as debonds and delaminations in Fiber Reinforced Polymer (FRP) bridge decks. Simulated sub-surface debonds and delaminations were inserted between the wearing surface and the underlying FRP deck specimens. The infrared thermography technique was used to detect these embedded subsurface defects. The use of various cooling and heating methods, including solar radiation, was explored. Surface temperature-time curves were established for different types and sizes of subsurface defects.

  5. Nondestructive evaluation technique using infrared thermography and terahertz imaging

    NASA Astrophysics Data System (ADS)

    Sakagami, Takahide; Shiozawa, Daiki; Tamaki, Yoshitaka; Iwama, Tatsuya

    2016-05-01

    Nondestructive testing (NDT) techniques using pulse heating infrared thermography and terahertz (THz) imaging were developed for detecting deterioration of oil tank floor, such as blister and delamination of corrosion protection coating, or corrosion of the bottom steel plate under coating. Experimental studies were conducted to demonstrate the practicability of developed techniques. It was found that the pulse heating infrared thermography was utilized for effective screening inspection and THz-TDS imaging technique performed well for the detailed inspection of coating deterioration and steel corrosion.

  6. Detection of pathogenic gram negative bacteria using infrared thermography

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Divya, M. P.; Bagavathiappan, S.; Thomas, Sabu; Philip, John

    2012-11-01

    Detection of viable bacteria is of prime importance in all fields of microbiology and biotechnology. Conventional methods of enumerating bacteria are often time consuming and labor-intensive. All living organisms generate heat due to metabolic activities and hence, measurement of heat energy is a viable tool for detection and quantification of bacteria. In this article, we employ a non-contact and real time method - infrared thermography (IRT) for measurement of temperature variations in four clinically significant gram negative pathogenic bacteria, viz. Vibrio cholerae, Vibrio mimicus, Proteus mirabilis and Pseudomonas aeruginosa. We observe that, the energy content, defined as the ratio of heat generated by bacterial metabolic activities to the heat lost from the liquid medium to the surrounding, vary linearly with the bacterial concentration in all the four pathogenic bacteria. The amount of energy content observed in different species is attributed to their metabolisms and morphologies that affect the convection velocity and hence heat transport in the medium.

  7. Using infrared thermography to study freezing in plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Factors that determine when and to what extent a plant will freeze are complex. While thermocouples have served as the main method of monitoring the freezing process in plants, infrared thermography offers distinct advantages, and the use of this latter technology has provided new insights on the p...

  8. Infrared thermography to evaluate lameness in pregnant sows

    PubMed Central

    Amezcua, Rocio; Walsh, Shannon; Luimes, Paul H.; Friendship, Robert M.

    2014-01-01

    Early detection of lameness in sows is important to reduce losses and improve animal welfare. Mild-to-moderate lameness is difficult to diagnose in sows. Infrared thermography (IRT) was evaluated as a method of detecting signs of inflammation in the lower limbs as an aid in lameness detection. PMID:24587511

  9. NASA MUST Paper: Infrared Thermography of Graphite/Epoxy

    NASA Technical Reports Server (NTRS)

    Comeaux, Kayla; Koshti, Ajay

    2010-01-01

    The focus of this project is to use Infrared Thermography, a non-destructive test, to detect detrimental cracks and voids beneath the surface of materials used in the space program. This project will consist of developing a simulation model of the Infrared Thermography inspection of the Graphite/Epoxy specimen. The simulation entails finding the correct physical properties for this specimen as well as programming the model for thick voids or flat bottom holes. After the simulation is completed, an Infrared Thermography inspection of the actual specimen will be made. Upon acquiring the experimental test data, an analysis of the data for the actual experiment will occur, which includes analyzing images, graphical analysis, and analyzing numerical data received from the infrared camera. The simulation will then be corrected for any discrepancies between it and the actual experiment. The optimized simulation material property inputs can then be used for new simulation for thin voids. The comparison of the two simulations, the simulation for the thick void and the simulation for the thin void, provides a correlation between the peak contrast ratio and peak time ratio. This correlation is used in the evaluation of flash thermography data during the evaluation of delaminations.

  10. Infrared thermography to detect residual ceramic in gas turbine blades

    NASA Astrophysics Data System (ADS)

    Meola, C.; Carlomagno, G. M.; di Foggia, M.; Natale, O.

    2008-06-01

    A serious problem in the production of gas turbine blades is the detection of residual ceramic cores inside the cooling passages; in fact, the presence of even small ceramic pieces affects turbine performance and may cause difficulties in successive manufacturing. Therefore, it is important to have a non-destructive technique that must be capable of detecting tiny ceramic fragments in a fast and easy way. In this perspective, the suitability of infrared thermography was investigated within cooperation between the University of Naples and the Europea Microfusioni Aerospaziali S.p.A. (EMA). Several blades of three different types were inspected revealing that in many cases infrared thermography can discover small ceramic fragments which were missed by X-ray inspection. In addition, infrared thermography allows gaining of information about other types of anomalies (e.g., surface defects) during the same testing step (by eventually changing the test parameters) and then saving time and money. The obtained results look promising in view of introducing infrared thermography among industrial instrumentation as an alternative to, or integrated with, the most currently utilized non-destructive techniques.

  11. Infrared thermography to evaluate lameness in pregnant sows.

    PubMed

    Amezcua, Rocio; Walsh, Shannon; Luimes, Paul H; Friendship, Robert M

    2014-03-01

    Early detection of lameness in sows is important to reduce losses and improve animal welfare. Mild-to-moderate lameness is difficult to diagnose in sows. Infrared thermography (IRT) was evaluated as a method of detecting signs of inflammation in the lower limbs as an aid in lameness detection.

  12. Infrared thermography on ocular surface temperature: A review

    NASA Astrophysics Data System (ADS)

    Tan, Jen-Hong; Ng, E. Y. K.; Rajendra Acharya, U.; Chee, C.

    2009-07-01

    Body temperature is a good indicator of human health. Thermal imaging system (thermography) is a non-invasive imaging procedure used to record the thermal patterns using Infrared (IR) camera. It provides visual and qualitative documentation of temperature changes in the vascular tissues, and is beginning to play an important role in the field of ophthalmology. This paper deals with the working principle, use and advantages of IR thermography in the field of ophthalmology. Different algorithms to acquire the ocular surface temperature (OST), that can be used for the diagnosis of ocular diseases are discussed.

  13. Heat flux sensors for infrared thermography in convective heat transfer.

    PubMed

    Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso

    2014-11-07

    This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described.

  14. Heat Flux Sensors for Infrared Thermography in Convective Heat Transfer

    PubMed Central

    Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso

    2014-01-01

    This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described. PMID:25386758

  15. Infrared thermography: A non-invasive window into thermal physiology.

    PubMed

    Tattersall, Glenn J

    2016-12-01

    Infrared thermography is a non-invasive technique that measures mid to long-wave infrared radiation emanating from all objects and converts this to temperature. As an imaging technique, the value of modern infrared thermography is its ability to produce a digitized image or high speed video rendering a thermal map of the scene in false colour. Since temperature is an important environmental parameter influencing animal physiology and metabolic heat production an energetically expensive process, measuring temperature and energy exchange in animals is critical to understanding physiology, especially under field conditions. As a non-contact approach, infrared thermography provides a non-invasive complement to physiological data gathering. One caveat, however, is that only surface temperatures are measured, which guides much research to those thermal events occurring at the skin and insulating regions of the body. As an imaging technique, infrared thermal imaging is also subject to certain uncertainties that require physical modelling, which is typically done via built-in software approaches. Infrared thermal imaging has enabled different insights into the comparative physiology of phenomena ranging from thermogenesis, peripheral blood flow adjustments, evaporative cooling, and to respiratory physiology. In this review, I provide background and guidelines for the use of thermal imaging, primarily aimed at field physiologists and biologists interested in thermal biology. I also discuss some of the better known approaches and discoveries revealed from using thermal imaging with the objective of encouraging more quantitative assessment.

  16. Visualization of In-Flight Flow Phenomena Using Infrared Thermography

    NASA Technical Reports Server (NTRS)

    Banks, D. W.; vanDam, C. P.; Shiu, H. J.; Miller, G. M.

    2000-01-01

    Infrared thermography was used to obtain data on the state of the boundary layer of a natural laminar flow airfoil in supersonic flight. In addition to the laminar-to-turbulent transition boundary, the infrared camera was able to detect shock waves and present a time dependent view of the flow field. A time dependent heat transfer code was developed to predict temperature distributions on the test subject and any necessary surface treatment. A commercially available infrared camera was adapted for airborne use in this application. Readily available infrared technology has the capability to provide detailed visualization of various flow phenomena in subsonic to hypersonic flight regimes.

  17. Normalized Temperature Contrast Processing in Flash Infrared Thermography

    NASA Technical Reports Server (NTRS)

    Koshti, Ajay M.

    2016-01-01

    The paper presents further development in normalized contrast processing of flash infrared thermography method by the author given in US 8,577,120 B1. The method of computing normalized image or pixel intensity contrast, and normalized temperature contrast are provided, including converting one from the other. Methods of assessing emissivity of the object, afterglow heat flux, reflection temperature change and temperature video imaging during flash thermography are provided. Temperature imaging and normalized temperature contrast imaging provide certain advantages over pixel intensity normalized contrast processing by reducing effect of reflected energy in images and measurements, providing better quantitative data. The subject matter for this paper mostly comes from US 9,066,028 B1 by the author. Examples of normalized image processing video images and normalized temperature processing video images are provided. Examples of surface temperature video images, surface temperature rise video images and simple contrast video images area also provided. Temperature video imaging in flash infrared thermography allows better comparison with flash thermography simulation using commercial software which provides temperature video as the output. Temperature imaging also allows easy comparison of surface temperature change to camera temperature sensitivity or noise equivalent temperature difference (NETD) to assess probability of detecting (POD) anomalies.

  18. Calibration and Evaluation of Ultrasound Thermography using Infrared Imaging

    PubMed Central

    Hsiao, Yi-Sing; Deng, Cheri X.

    2015-01-01

    Real-time monitoring of the spatiotemporal evolution of tissue temperature is important to ensure safe and effective treatment in thermal therapies including hyperthermia and thermal ablation. Ultrasound thermography has been proposed as a non-invasive technique for temperature measurement, and accurate calibration of the temperature-dependent ultrasound signal changes against temperature is required. Here we report a method that uses infrared (IR) thermography for calibration and validation of ultrasound thermography. Using phantoms and cardiac tissue specimens subjected to high-intensity focused ultrasound (HIFU) heating, we simultaneously acquired ultrasound and IR imaging data from the same surface plane of a sample. The commonly used echo time shift-based method was chosen to compute ultrasound thermometry. We first correlated the ultrasound echo time shifts with IR-measured temperatures for material-dependent calibration and found that the calibration coefficient was positive for fat-mimicking phantom (1.49 ± 0.27) but negative for tissue-mimicking phantom (− 0.59 ± 0.08) and cardiac tissue (− 0.69 ± 0.18 °C-mm/ns). We then obtained the estimation error of the ultrasound thermometry by comparing against the IR measured temperature and revealed that the error increased with decreased size of the heated region. Consistent with previous findings, the echo time shifts were no longer linearly dependent on temperature beyond 45 – 50 °C in cardiac tissues. Unlike previous studies where thermocouples or water-bath techniques were used to evaluate the performance of ultrasound thermography, our results show that high resolution IR thermography provides a useful tool that can be applied to evaluate and understand the limitations of ultrasound thermography methods. PMID:26547634

  19. Detecting defects in marine structures by using eddy current infrared thermography.

    PubMed

    Swiderski, W

    2016-12-01

    Eddy current infrared (IR) thermography is a new nondestructive testing (NDT) technique used for the detection of cracks in electroconductive materials. By combining the well-established inspection methods of eddy current NDT and IR thermography, this technique uses induced eddy currents to heat test samples. In this way, IR thermography allows the visualization of eddy current distribution that is distorted in defect sites. This paper discusses the results of numerical modeling of eddy current IR thermography procedures in application to marine structures.

  20. Infrared Contrast Analysis Technique for Flash Thermography Nondestructive Evaluation

    NASA Technical Reports Server (NTRS)

    Koshti, Ajay

    2014-01-01

    The paper deals with the infrared flash thermography inspection to detect and analyze delamination-like anomalies in nonmetallic materials. It provides information on an IR Contrast technique that involves extracting normalized contrast verses time evolutions from the flash thermography infrared video data. The paper provides the analytical model used in the simulation of infrared image contrast. The contrast evolution simulation is achieved through calibration on measured contrast evolutions from many flat bottom holes in the subject material. The paper also provides formulas to calculate values of the thermal measurement features from the measured contrast evolution curve. Many thermal measurement features of the contrast evolution that relate to the anomaly characteristics are calculated. The measurement features and the contrast simulation are used to evaluate flash thermography inspection data in order to characterize the delamination-like anomalies. In addition, the contrast evolution prediction is matched to the measured anomaly contrast evolution to provide an assessment of the anomaly depth and width in terms of depth and diameter of the corresponding equivalent flat-bottom hole (EFBH) or equivalent uniform gap (EUG). The paper provides anomaly edge detection technique called the half-max technique which is also used to estimate width of an indication. The EFBH/EUG and half-max width estimations are used to assess anomaly size. The paper also provides some information on the "IR Contrast" software application, half-max technique and IR Contrast feature imaging application, which are based on models provided in this paper.

  1. Automatic Detection of Subsurface Defects Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Lonkar, G. M.; Klinkhachorn, P.; Halabe, Udaya B.; GangaRao, H. V. S.

    2005-04-01

    The popularity of FRP bridge decks has increased in recent times because of their high strength to weight ratio, fatigue resistance etc. Defects due to degradation of the bridge deck malign their properties and adversely affect the structural integrity. These defects need to be detected and continuously monitored using field techniques such as infrared thermography. The process of manually analyzing the infrared images is tedious and ambiguous. Instead, using software algorithms on the infrared images of FRP decks can increase the defect detection speed and accuracy. This paper proposes a software automated defect detection technique to detect subsurface anomalies in fiber reinforced polymer (FRP) bridge decks. Thermal images of the FRP decks were captured using a radiometric infrared camera. Software algorithms using morphological image processing and fuzzy clustering techniques were developed to analyze the images for detecting the defects automatically. They were tested on infrared images of FRP bridge decks prepared in the laboratory. In the tests conducted, simulated subsurface defects of varying size, thickness and wearing surfaces were fabricated in the laboratory. The tests include a performance analysis of detecting delaminations and debonds, and the effect of distance on the detecting ability of the algorithm. The algorithms were also tested with FRP deck specimens under solar radiation, to test the response under a passive heat source. The study showed that Infrared Thermography can be effectively used to detect subsurface defects and the process can be automated with substantial accuracy.

  2. Nde of Frp Wrapped Columns Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Halabe, Udaya B.; Dutta, Shasanka Shekhar; GangaRao, Hota V. S.

    2008-02-01

    This paper investigates the feasibility of using Infrared Thermography (IRT) for detecting debonds in Fiber Reinforced Polymer (FRP) wrapped columns. Laboratory tests were conducted on FRP wrapped concrete cylinders of size 6″×12″ (152.4 mm×304.8 mm) in which air-filled and water-filled debonds of various sizes were placed underneath the FRP wraps. Air-filled debonds were made by cutting plastic sheets into the desired sizes whereas water-filled debonds were made by filling water in custom made polyethylene pouches. Both carbon and glass fiber reinforced wraps were considered in this study. Infrared tests were conducted using a fully radiometric digital infrared camera which was successful in detecting air-filled as well as water-filled subsurface debonds. In addition to the laboratory testing, two field trips were made to Moorefield, West Virginia for detecting subsurface debonds in FRP wrapped timber piles of a railroad bridge using infrared testing. The results revealed that infrared thermography can be used as an effective nondestructive evaluation tool for detecting subsurface debonds in structural components wrapped with carbon or glass reinforced composite fabrics.

  3. Infrared thermography of solid surfaces in a fire

    NASA Astrophysics Data System (ADS)

    Meléndez, J.; Foronda, A.; Aranda, J. M.; López, F.; López del Cerro, F. J.

    2010-10-01

    Fire resistance tests are commonplace in industry. The aerospace sector is particularly active in this area, since the behaviour of advanced materials, such as composites, when in a fire is not fully understood yet. Two of the main obstacles are the inherent difficulty of direct surface measurements in such a harsh environment (especially on the exposed side of the specimens) and the lack of spatial resolution of the usual measuring devices, namely thermocouples (TCs). This paper presents a way to overcome these problems by using an infrared (IR) camera to study the exposed side of composite plates exposed to fire. A method for minimizing the effect of the flame (thus making it as 'transparent' as possible) was developed, resulting in 2D temperature maps of the plate surface. The assumptions that the method relies on were verified by data analysis and ad hoc emission-transmission experiments. The errors associated with two slightly different versions of the method were studied, and comparisons with TC measurements were performed. It was found that the IR method provides better results than TCs, not only due to its spatial resolution capability but also because of the non-intrusive nature of IR thermography, as opposed to the local effects caused by TCs, which became evident during the experiments.

  4. The Effectiveness of Infrared Thermography in Patients with Whiplash Injury

    PubMed Central

    Lee, Young Seo; Farhadi, Hooman F.; Lee, Won Hee; Kim, Sung Tae; Lee, Kun Su

    2015-01-01

    Objective This study aims to visualize the subjective symptoms before and after the treatment of whiplash injury using infrared (IR) thermography. Methods IR thermography was performed for 42 patients who were diagnosed with whiplash injury. There were 19 male and 23 female patients. The mean age was 43.12 years. Thermal differences (ΔT) in the neck and shoulder and changes in the thermal differences (ΔdT) before and after treatment were analyzed. Pain after injury was evaluated using visual analogue scale (VAS) before and after treatment (ΔVAS). The correlations between ΔdT and ΔVAS results before and after the treatment were examined. We used Digital Infrared Thermal Imaging equipment of Dorex company for IR thermography. Results The skin temperature of the neck and shoulder immediately after injury showed 1-2℃ hyperthermia than normal. After two weeks, the skin temperature was normal range. ΔT after immediately injuy was higher than normal value, but it was gradually near the normal value after two weeks. ΔdT before and after treatment were statistically significant (p<0.05). VAS of the neck and shoulder significantly reduced after 2 week (p=0.001). Also, there was significant correlation between ΔdT and reduced ΔVAS (the neck; r=0.412, p<0.007) (the shoulder; r=0.648, p<0.000). Conclusion The skin temperature of sites with whiplash injury is immediately hyperthermia and gradually decreased after two weeks, finally it got close to normal temperature. These were highly correlated with reduced VAS. IR thermography can be a reliable tool to visualize the symptoms of whiplash injury and the effectiveness of treatment in clinical settings. PMID:25932296

  5. Integration of active thermography into the assessment of cultural heritage buildings

    NASA Astrophysics Data System (ADS)

    Maierhofer, Christiane; Röllig, Mathias; Krankenhagen, Rainer

    2010-10-01

    Applications of infrared thermography in civil engineering are not limited to the identification of heat losses in building envelopes. Active infrared thermography methods enable structural investigations of building elements with one-sided access up to a depth of about 10 cm. Masonry and especially historical masonry has a very heterogeneous structure containing several different materials (brick, stone, mortar, plaster, wood, metal, etc.) with various thermal properties. As many classes of damage originate from defects that are close to the surface, active thermography is in general very well suited to assessing different test problems in cultural heritage buildings. In this paper, the physical background, equipment, environmental influences and material properties are discussed. Several application results are presented. It is shown how active thermography can be integrated into a holistic approach for the assessment of historical structures.

  6. In-Flight Flow Visualization Using Infrared Thermography

    NASA Technical Reports Server (NTRS)

    vanDam, C. P.; Shiu, H. J.; Banks D. W.

    1997-01-01

    The feasibility of remote infrared thermography of aircraft surfaces during flight to visualize the extent of laminar flow on a target aircraft has been examined. In general, it was determined that such thermograms can be taken successfully using an existing airplane/thermography system (NASA Dryden's F-18 with infrared imaging pod) and that the transition pattern and, thus, the extent of laminar flow can be extracted from these thermograms. Depending on the in-flight distance between the F-18 and the target aircraft, the thermograms can have a spatial resolution of as little as 0.1 inches. The field of view provided by the present remote system is superior to that of prior stationary infrared thermography systems mounted in the fuselage or vertical tail of a subject aircraft. An additional advantage of the present experimental technique is that the target aircraft requires no or minimal modifications. An image processing procedure was developed which improves the signal-to-noise ratio of the thermograms. Problems encountered during the analog recording of the thermograms (banding of video images) made it impossible to evaluate the adequacy of the present imaging system and image processing procedure to detect transition on untreated metal surfaces. The high reflectance, high thermal difussivity, and low emittance of metal surfaces tend to degrade the images to an extent that it is very difficult to extract transition information from them. The application of a thin (0.005 inches) self-adhesive insulating film to the surface is shown to solve this problem satisfactorily. In addition to the problem of infrared based transition detection on untreated metal surfaces, future flight tests will also concentrate on the visualization of other flow phenomena such as flow separation and reattachment.

  7. Mastitis detection in sheep by infrared thermography.

    PubMed

    Martins, Rafhael Felipe Saraiva; do Prado Paim, Tiago; de Abreu Cardoso, Cyntia; Stéfano Lima Dallago, Bruno; de Melo, Cristiano Barros; Louvandini, Helder; McManus, Concepta

    2013-06-01

    This study aims to evaluate the use of an infrared thermograph for mastitis diagnosis in sheep. Thirty-seven Santa Inês ewes were evaluated weekly through infrared images obtained with thermograph FLIR System Series-i®. Milk was collected for somatic cell count and milk compound level determination. The clinical mastitis group had the highest fat and protein level, as well as the lowest lactose level. The udder temperatures were higher for subclinical mastitis group. The udder temperature data was able to correctly classify the animals into the mastitis groups and the canonical analysis showed that these temperatures clearly differentiated the subclinical mastitis groups from the others. Therefore, this study showed that udder infrared temperatures can be used as diagnostic method to mastitis in sheep.

  8. Efficient reconstruction of corrosion profiles by infrared thermography

    NASA Astrophysics Data System (ADS)

    Marcuzzi, F.; Marinetti, S.

    2008-07-01

    In this paper, we propose a novel algorithm to solve the hidden corrosion estimation problem from experimental data produced by infrared thermography. This is therefore a thermal inverse problem. The algorithm is put in a predictor-corrector form and uses an Adaptive Finite Element model as the reference model. The adaptation is done in the (linear) predictor step, while the parameter estimation is done in the (nonlinear) corrector step. An ad-hoc regularization strategy has been developed. Experiments with real data have confirmed the effectiveness of the method. Considerable computational savings have been achieved compared to a standard algorithm formulation.

  9. Finite Element Modeling for Infrared Thermography of Gfrp Bridge Decks

    NASA Astrophysics Data System (ADS)

    Hing, Cheng L.; Halabe, Udaya B.

    2008-02-01

    Glass Fiber Reinforced Polymer (GFRP) composite bridge decks are increasingly being used as replacements for old concrete decks and for new construction. The service performance of the GFRP bridge decks can be adversely affected by the formation of debonds between the wearing surface and the underlying bridge deck. Past experimental studies by the authors have shown the usefulness of the infrared thermography technique in detecting the subsurface debonds prior to maintenance and rehabilitation work. This paper investigates the use of finite element (FE) heat transfer modeling to predict infrared thermography images from GFRP bridge decks with subsurface debonds. The paper includes measurement of thermal properties of the GFRP bridge deck and the wearing surface, and heat transfer FE modeling of decks with debonds of different thicknesses. The results show that FE modeling can be a useful tool for predicting surface temperature profile under different heating conditions and debond sizes. Such predictions can help determine the required heat intensity and detectable debond sizes prior to experimental data acquisition in the field using an infrared camera.

  10. Detection of tanker defects with infrared thermography

    NASA Technical Reports Server (NTRS)

    Kantsios, A. G.

    1980-01-01

    Infrared scanning technique for finding defects in secondary barrier of liquid natural gas (LNG) tank has been successfully tested on ship under construction at Newport News Shipbuilding and Dry Dock Company. Technique determines defects with minimal expenditure of time and manpower. Tests could be repeated during life of tanker and make more complicated testing unnecessary. Tests also confirmed that tank did not have any major defects, and tank was certified.

  11. Detecting Moisture In Buildings Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Marshall, Stephen J.

    1981-01-01

    Visual examination is a reliable means of moisture detection in building walls after serious damaR'e has been done. Traditional spot measurement instruments are inexpedient devices for elusive moisture detection in heterogeneous materials. The infrared thermal imaging system was found t be a more versatile tool for in-situ moisture detection because of its unique characteristics. Several thermographic examples of moisture detection in. building walls are presented, which will aid the reader in the qualitative interpretation o1 therm.ograms 1or moisture problem.s.

  12. Noninvasive diagnosis of seed viability using infrared thermography

    PubMed Central

    Kranner, Ilse; Kastberger, Gerald; Hartbauer, Manfred; Pritchard, Hugh W.

    2010-01-01

    Recent advances in the noninvasive analyses of plant metabolism include stress imaging techniques, mainly developed for vegetative tissues. We explored if infrared thermography can be used to predict whether a quiescent seed will germinate or die upon water uptake. Thermal profiles of viable, aged, and dead Pisum sativum seeds were recorded, and image analysis of 22,000 images per individual seed showed that infrared thermography can detect imbibition- and germination-associated biophysical and biochemical changes. These “thermal fingerprints” vary with viability in this species and in Triticum aestivum and Brassica napus seeds. Thermogenesis of the small individual B. napus seeds was at the limit of the technology. We developed a computer model of “virtual pea seeds,” that uses Monte Carlo simulation, based on the heat production of major seed storage compounds to unravel physico-chemical processes of thermogenesis. The simulation suggests that the cooling that dominates the early thermal profiles results from the dissolution of low molecular-weight carbohydrates. Moreover, the kinetics of the production of such “cooling” compounds over the following 100 h is dependent on seed viability. We also developed a deterministic tool that predicts in the first 3 hours of water uptake, when seeds can be redried and stored again, whether or not a pea seed will germinate. We believe that the early separation of individual, ungerminated seeds (live, aged, or dead) before destructive germination assessment creates unique opportunities for integrative studies on cell death, differentiation, and development. PMID:20133712

  13. Robust remote monitoring of breathing function by using infrared thermography.

    PubMed

    Pereira, Carina B; Yu, Xinchi; Blazek, Vladimir; Leonhardt, Steffen

    2015-01-01

    An abnormal breathing rate (BR) is one of the strongest markers of physiological distress. Moreover, it plays an important role in early detection of sudden infant death syndrome, as well as in the diagnosis of respiratory disorders. However, the current measuring modalities can cause discomfort to the patient, since attachment to the patient's body is required. This paper proposes a new approach based on infrared thermography to remotely monitor BR. This method allows to (1) detect automatically the nose, (2) track the associate region of interest (ROI), and (3) extract BR. To evaluate the performance of this method, thermal recording of 5 healthy subjects were acquired. Results were compared with BR obtained by capnography. The introduced approach demonstrated an excellent performance. ROIs were precisely segmented and tracked. Furthermore, a Bland-Altman diagram showed a good agreement between estimated BR and gold standard. The mean correlation and mean absolute BR error are 0.92 ± 0.07 and 0.53 bpm, respectively. In summary, infrared thermography seems to be a great, clinically relevant alternative to attached sensors, due to its outstanding characteristics and performance.

  14. Technical design note: differential infrared thermography of methane jets

    NASA Astrophysics Data System (ADS)

    Golzke, Hendrik; Leick, Philippe; Dreizler, Andreas

    2016-10-01

    In this note a novel approach for temperature measurements of methane jets is presented. Differential infrared thermography (DIT) is a contactless, tracer-free temperature determination method for semi-transparent objects, based on an infrared camera. DIT does not rely on a specific a priori value for the emissivity, but typically assumes constant emissivity within the relevant wavelength band. This is reasonable for complex hydrocarbons (i.e. as in liquid fuel sprays) but no longer justified for the discrete absorption spectrum of simple molecules such as methane. An alternative approximation is suggested and discussed, and the feasibility of DIT for the study of supercritical methane jets in a pressure chamber at conditions relevant for internal combustion engines is demonstrated. As DIT also determines the gas emissivity, a combined two-dimensional temperature and projected density visualisation becomes possible and is shown to highlight supersonic structurues such as Mach disks.

  15. Dual-band infrared thermography for quantitative nondestructive evaluation

    SciTech Connect

    Durbin, P.F.; Del Grande, N.K.; Dolan, K.W.; Perkins, D.E.; Shapiro, A.B.

    1993-04-01

    The authors have developed dual-band infrared (DBIR) thermography that is being applied to quantitative nondestructive evaluation (NDE) of aging aircraft. The DBIR technique resolves 0.2 degrees C surface temperature differences for inspecting interior flaws in heated aircraft structures. It locates cracks, corrosion sites, disbonds or delaminations in metallic laps and composite patches. By removing clutter from surface roughness effects, the authors clarify interpretation of subsurface flaws. To accomplish this, the authors ratio images recorded at two infrared bands, centered near 5 microns and 10 microns. These image ratios are used to decouple temperature patterns associated with interior flaw sites from spatially varying surface emissivity noise. They also discuss three-dimensional (3D) dynamic thermal imaging of structural flaws using dual-band infrared (DBIR) computed tomography. Conventional thermography provides single-band infrared images which are difficult to interpret. Standard procedures yield imprecise (or qualitative) information about subsurface flaw sites which are typically masked by surface clutter. They use a DBIR imaging technique pioneered at LLNL to capture the time history of surface temperature difference patterns for flash-heated targets. They relate these patterns to the location, size, shape and depth of subsurface flaws. They have demonstrated temperature accuracies of 0.2{degree}C, timing synchronization of 3 ms (after onset of heat flash) and intervals of 42 ms, between images, during an 8 s cooling (and heating) interval characterizing the front (and back) surface temperature-time history of an epoxy-glue disbond site in a flash-heated aluminum lap joint.

  16. Infra-red thermography in the assessment of sacro-iliac inflammation.

    PubMed

    Grennan, D M; Caygill, L

    1982-05-01

    In a cross-sectional study designed to investigate the sensitivity of infra-red thermography in the detection of sacro-iliac regions were examined by thermography in a group of patients with ankylosing spondylitis and compared with normal volunteers and patients with other causes of low back pain. Thermograms were recorded both quantitatively via profile measurements across the sacro-iliac regions and sacrum and qualitatively via the pattern recorded by photography. Sacro-iliac disease activity was recorded clinically on the same day and was low overall in the patients examined. Thirteen of the 30 ankylosing spondylitis patients were abnormal thermographically either by profile or pattern measurements. None of the 13 patients with other causes of low back pain had increased sacro-iliac activity on thermography. None of four patients without X-ray evidence of sacro-iliitis was abnormal thermographically but there was a trend for increasing thermographic activity to be associated with increasing clinical activity. It was concluded that the thermographic technique examined was of little help in the diagnosis of early sacro-iliitis but might be more helpful in the objective serial assessment of sacro-iliitis in individual patients with active disease.

  17. Investigation of Various Essential Factors for Optimum Infrared Thermography

    PubMed Central

    OKADA, Keiji; TAKEMURA, Kei; SATO, Shigeru

    2013-01-01

    ABSTRACT We investigated various essential factors for optimum infrared thermography for cattle clinics. The effect of various factors on the detection of surface temperature was investigated in an experimental room with a fixed ambient temperature using a square positioned on a wall. Various factors of animal objects were examined using cattle to determine the relationships among presence of hair, body surface temperature, surface temperature of the eyeball, the highest temperature of the eye circle, rectum temperature and ambient temperature. Also, the surface temperature of the flank at different time points after eating was examined. The best conditions of thermography for cattle clinics were determined and were as follows: (1) The distance between a thermal camera and an object should be fixed, and the camera should be set within a 45-degree angle with respect to the objects using the optimum focal length. (2) Factors that affect the camera temperature, such as extreme cold or heat, direct sunshine, high humidity and wind, should be avoided. (3) For the comparison of thermographs, imaging should be performed under identical conditions. If this is not achievable, hairless parts should be used. PMID:23759714

  18. Investigation of various essential factors for optimum infrared thermography.

    PubMed

    Okada, Keiji; Takemura, Kei; Sato, Shigeru

    2013-10-01

    We investigated various essential factors for optimum infrared thermography for cattle clinics. The effect of various factors on the detection of surface temperature was investigated in an experimental room with a fixed ambient temperature using a square positioned on a wall. Various factors of animal objects were examined using cattle to determine the relationships among presence of hair, body surface temperature, surface temperature of the eyeball, the highest temperature of the eye circle, rectum temperature and ambient temperature. Also, the surface temperature of the flank at different time points after eating was examined. The best conditions of thermography for cattle clinics were determined and were as follows: (1) The distance between a thermal camera and an object should be fixed, and the camera should be set within a 45-degree angle with respect to the objects using the optimum focal length. (2) Factors that affect the camera temperature, such as extreme cold or heat, direct sunshine, high humidity and wind, should be avoided. (3) For the comparison of thermographs, imaging should be performed under identical conditions. If this is not achievable, hairless parts should be used.

  19. Clinical application of infrared thermography in diagnosis and therapeutic assessment of vascular ischemic pain.

    PubMed

    Hsieh, J C; Chan, K H; Lui, P W; Lee, T Y

    1990-12-01

    Temperature is a very important and useful manifestation of various disease entities. The importance of body temperature as an indicator of disease has been known for centuries but in recent years attention has also been paid to how to conveniently and effectively make use of skin temperature as a diagnostic tool. Skin temperature can be measured with thermocouples, electronic thermistor-thermometers, electronic integrators, liquid crystal thermography, and infrared thermography. The temperature of extremities is largely dependent on the blood flow through peripheral vessels, and in the study of vascular diseases thermography has been, therefore, found to be useful. Blood flow can be assessed by many methods including washout techniques or laser Doppler flowmetry. Of these, infrared thermography has the advantages of being noninvasive, remote from the patient when in use, and capable of producing multiple recordings at short time intervals. Here we present a case of vascular ischemic pain which was diagnosed and therapeutically assessed by thermography.

  20. Real time capable infrared thermography for ASDEX Upgrade

    NASA Astrophysics Data System (ADS)

    Sieglin, B.; Faitsch, M.; Herrmann, A.; Brucker, B.; Eich, T.; Kammerloher, L.; Martinov, S.

    2015-11-01

    Infrared (IR) thermography is widely used in fusion research to study power exhaust and incident heat load onto the plasma facing components. Due to the short pulse duration of today's fusion experiments, IR systems have mostly been designed for off-line data analysis. For future long pulse devices (e.g., Wendelstein 7-X, ITER), a real time evaluation of the target temperature and heat flux is mandatory. This paper shows the development of a real time capable IR system for ASDEX Upgrade. A compact IR camera has been designed incorporating the necessary magnetic and electric shielding for the detector, cooler assembly. The camera communication is based on the Camera Link industry standard. The data acquisition hardware is based on National Instruments hardware, consisting of a PXIe chassis inside and a fibre optical connected industry computer outside the torus hall. Image processing and data evaluation are performed using real time LabVIEW.

  1. Advanced Image Processing for Defect Visualization in Infrared Thermography

    NASA Technical Reports Server (NTRS)

    Plotnikov, Yuri A.; Winfree, William P.

    1997-01-01

    Results of a defect visualization process based on pulse infrared thermography are presented. Algorithms have been developed to reduce the amount of operator participation required in the process of interpreting thermographic images. The algorithms determine the defect's depth and size from the temporal and spatial thermal distributions that exist on the surface of the investigated object following thermal excitation. A comparison of the results from thermal contrast, time derivative, and phase analysis methods for defect visualization are presented. These comparisons are based on three dimensional simulations of a test case representing a plate with multiple delaminations. Comparisons are also based on experimental data obtained from a specimen with flat bottom holes and a composite panel with delaminations.

  2. High speed heterodyne infrared thermography applied to thermal diffusivity identification.

    PubMed

    Pradere, C; Clerjaud, L; Batsale, J C; Dilhaire, S

    2011-05-01

    We have combined InfraRed thermography and thermal wave techniques to perform microscale, ultrafast (microsecond) temperature field measurements. The method is based on an IR camera coupled to a microscope and synchronized to the heat source by means of phase locked function generators. The principle is based on electronic stroboscopic sampling where the low IR camera acquisition frequency f(acq) (25 Hz) undersamples a high frequency thermal wave. This technique permits the measurement of the emissive thermal response at a (microsecond) short time scale (microsecond) with the full frame mode of the IR camera with a spatial thermal resolution of 7 μm. Then it becomes possible to study 3D transient heat transfer in heterogeneous and high thermal conductive thin layers. Thus it is possible for the first time in our knowledge to achieve temperature field measurements in heterogeneous media within a wide range of time domains. The IR camera is now a suitable instrument for multiscale thermal analysis.

  3. Real time capable infrared thermography for ASDEX Upgrade

    SciTech Connect

    Sieglin, B. Faitsch, M.; Herrmann, A.; Brucker, B.; Eich, T.; Kammerloher, L.; Martinov, S.

    2015-11-15

    Infrared (IR) thermography is widely used in fusion research to study power exhaust and incident heat load onto the plasma facing components. Due to the short pulse duration of today’s fusion experiments, IR systems have mostly been designed for off-line data analysis. For future long pulse devices (e.g., Wendelstein 7-X, ITER), a real time evaluation of the target temperature and heat flux is mandatory. This paper shows the development of a real time capable IR system for ASDEX Upgrade. A compact IR camera has been designed incorporating the necessary magnetic and electric shielding for the detector, cooler assembly. The camera communication is based on the Camera Link industry standard. The data acquisition hardware is based on National Instruments hardware, consisting of a PXIe chassis inside and a fibre optical connected industry computer outside the torus hall. Image processing and data evaluation are performed using real time LabVIEW.

  4. Monitoring Sintering Burn-Through Point Using Infrared Thermography

    PubMed Central

    Usamentiaga, Rubén; Molleda, Julio; Garcia, Daniel F.; Bulnes, Francisco G.

    2013-01-01

    Sintering is a complex industrial process that applies heat to fine particles of iron ore and other materials to produce sinter, a solidified porous material used in blast furnaces. The sintering process needs to be carefully adjusted, so that the combustion zone reaches the bottom of the material just before the discharge end. This is known as the burn-through point. Many different parameters need to be finely tuned, including the speed and the quantities of the materials mixed. However, in order to achieve good results, sintering control requires precise feedback to adjust these parameters. This work presents a sensor to monitor the sintering burn-through point based on infrared thermography. The proposed procedure is based on the acquisition of infrared images at the end of the sintering process. At this position, infrared images contain the cross-section temperatures of the mixture. The objective of this work is to process this information to extract relevant features about the sintering process. The proposed procedure is based on four steps: key frame detection, region of interest detection, segmentation and feature extraction. The results indicate that the proposed procedure is very robust and reliable, providing features that can be used effectively to control the sintering process. PMID:23939585

  5. Use of modern infrared thermography for wildlife population surveys

    NASA Astrophysics Data System (ADS)

    Garner, Dale L.; Underwood, H. Brian; Porter, William F.

    1995-03-01

    A commercially available thermal-infrared scanning system was used to survey populations of several wildlife species. The system's ability to detect species of different sizes in varying habitats relative to conventional survey methods, to differentiate between species in the same habitat, and the influence of environtmental factors on operational aspects of employing this technology in the field were evaluated. Total costs for the surveys were approximately 0.36/ha. There were marked discrepancies in the counts of untrained observers and those from trained analysis. Computer-assisted analysis of infrared imagery recorded 52% fewer deer than were estimated from drive counts, and densities of moose were five times those estimated from conventional aerial methods. By flying concentric circles and using telephoto, detailed counts of turkeys and deer were possible. With the aid of computer-assisted analysis, infrared thermography may become a useful wildlife population survey tool. More research is needed to verify the actual efficiency of detection by combining aerial scans with ground truthing for a variely of species and habitals.

  6. Monitoring sintering burn-through point using infrared thermography.

    PubMed

    Usamentiaga, Rubén; Molleda, Julio; Garcia, Daniel F; Bulnes, Francisco G

    2013-08-09

    Sintering is a complex industrial process that applies heat to fine particles of iron ore and other materials to produce sinter, a solidified porous material used in blast furnaces. The sintering process needs to be carefully adjusted, so that the combustion zone reaches the bottom of the material just before the discharge end. This is known as the burn-through point. Many different parameters need to be finely tuned, including the speed and the quantities of the materials mixed. However, in order to achieve good results, sintering control requires precise feedback to adjust these parameters. This work presents a sensor to monitor the sintering burn-through point based on infrared thermography. The proposed procedure is based on the acquisition of infrared images at the end of the sintering process. At this position, infrared images contain the cross-section temperatures of the mixture. The objective of this work is to process this information to extract relevant features about the sintering process. The proposed procedure is based on four steps: key frame detection, region of interest detection, segmentation and feature extraction. The results indicate that the proposed procedure is very robust and reliable, providing features that can be used effectively to control the sintering process.

  7. Infrared ocular thermography in dogs with and without keratoconjunctivitis sicca.

    PubMed

    Biondi, Flávia; Dornbusch, Peterson T; Sampaio, Manuella; Montiani-Ferreira, Fabiano

    2015-01-01

    Infrared thermography was used to measure temperature differences of the corneal surface between nasal and temporal limbus regions and central cornea of normal dogs and dogs with keratoconjunctivitis sicca (KCS), in order to establish temperature values in normal canine eyes and in patients with decreased Schirmer tear tests (STT) values. Dogs investigated were all either patients seen at the Veterinary Teaching Hospital of Federal University of Paraná or normal dogs that belonged to the same institution. STT were performed in all eyes. A total of 40 control eyes (STT ≥15 mm/min) and 20 eyes with low STT values (STT ≤14 mm/min) were examined. The mean STT value for eyes with normal STT values was 22.9 ± 3.9 mm/min (mean ± standard deviation), and the mean STT value for eyes with low STT value was 7.2 ± 4.8 mm/min. The mean corneal temperature was significantly lower in eyes with low STT values than in control eyes (P < 0.0001). The following significant correlations were found: (i) Schirmer and breakup time (BUT) (P = 0.0001, r = 0.5); (ii) STT values and corneal surface temperature (P = 0.001, r = 0.256); (iii) STT values and age (P = 0.0001, r = -0.448); (iv) age and corneal surface temperature (P = 0.0001, r = -0.281); and (v) BUT and corneal surface temperature (P = 0.0001, r = 0.36). Thermography is a method that can differentiate between eyes with normal and abnormal STT values. In the future, thermography might be incorporated as part of the ophthalmic examination and perhaps become a popular ancillary test for the diagnoses of ocular surface disorders.

  8. Application of infrared thermography in computer aided diagnosis

    NASA Astrophysics Data System (ADS)

    Faust, Oliver; Rajendra Acharya, U.; Ng, E. Y. K.; Hong, Tan Jen; Yu, Wenwei

    2014-09-01

    The invention of thermography, in the 1950s, posed a formidable problem to the research community: What is the relationship between disease and heat radiation captured with Infrared (IR) cameras? The research community responded with a continuous effort to find this crucial relationship. This effort was aided by advances in processing techniques, improved sensitivity and spatial resolution of thermal sensors. However, despite this progress fundamental issues with this imaging modality still remain. The main problem is that the link between disease and heat radiation is complex and in many cases even non-linear. Furthermore, the change in heat radiation as well as the change in radiation pattern, which indicate disease, is minute. On a technical level, this poses high requirements on image capturing and processing. On a more abstract level, these problems lead to inter-observer variability and on an even more abstract level they lead to a lack of trust in this imaging modality. In this review, we adopt the position that these problems can only be solved through a strict application of scientific principles and objective performance assessment. Computing machinery is inherently objective; this helps us to apply scientific principles in a transparent way and to assess the performance results. As a consequence, we aim to promote thermography based Computer-Aided Diagnosis (CAD) systems. Another benefit of CAD systems comes from the fact that the diagnostic accuracy is linked to the capability of the computing machinery and, in general, computers become ever more potent. We predict that a pervasive application of computers and networking technology in medicine will help us to overcome the shortcomings of any single imaging modality and this will pave the way for integrated health care systems which maximize the quality of patient care.

  9. Exit Presentation: Infrared Thermography on Graphite/Epoxy

    NASA Technical Reports Server (NTRS)

    Comeaux, Kayla

    2010-01-01

    This slide presentation reports on the internship project that was accomplished during the summer of 2010. The objectives of the project were to: (1) Simulate Flash Thermography on Graphite/Epoxy Flat Bottom hole Specimen and thin void specimens, (2) Obtain Flash Thermography data on Graphite/Epoxy flat bottom hole specimens, (3) Compare experimental results with simulation results, Compare Flat Bottom Hole Simulation with Thin Void Simulation to create a graph to determine size of IR Thermography detected defects

  10. Infrared thermography of the tear film in dry eye.

    PubMed

    Morgan, P B; Tullo, A B; Efron, N

    1995-01-01

    Infrared ocular thermograms were recorded for a group of 36 dry eye patients and for 27 age- and sex-matched controls. Mean ocular surface temperature was greater in the dry eye group (32.38 +/- 0.69 degrees C) compared with the control group (31.94 +/- 0.54 degrees C; p < 0.01). In addition, there was a greater variation of temperatures across the ocular surface in the dry eye group, illustrated by the difference in temperature between the limbus and the centre of the cornea (0.64 +/- 0.20 degrees C in dry eye patients compared with 0.41 +/- 0.20 degrees C in the control group; p < 0.001). This parameter was also shown to be greater in dry eye patients who displayed either a fast tear break-up time or a poor Schirmer's test result. Infrared thermography is a non-invasive and objective technique that may prove a useful research tool for study of the tear film, its deficiencies and its various treatment modalities.

  11. Evaluation of mean skin temperature formulas by infrared thermography

    NASA Astrophysics Data System (ADS)

    Choi, J. K.; Miki, K.; Sagawa, S.; Shiraki, K.

    To study the reliabiliity of formulas for calculating mean skin temperature (Tsk), values were computed by 18 different techniques and were compared with the mean of 10,841 skin temperatures measured by infrared thermography. One hundred whole-body infrared thermograms were scanned in ten resting males while changing the air temperature from 40° C to 4° C. Local, regional average and mean skin temperatures were obtained using an image processing system. The agreement frequency, defined as the percentage of the calculated Tsk values which agreed with the corresponding infrared thermographic Tsk within +/-0.2° C, ranged for with the various formulas from 7% to 80%. In many sites, the local skin temperature did not coincide with the regional average skin temperature. When the local skin temperatures which showed the highest percentage similarity to the regional average skin temperature within +/-0.4° C were applied to the formula, the agreement frequency was markedly improved for all formulas. However, the agreement frequency was not affected by changing the weighting factors from specific constants to individually measured values of regional surface area. By applying the physiologically reliable accuracy range of +/-0.2° C in the moderate and +/-0.4° C in the cool condition, agreement frequencies of at least 95% were observed in formulas involving seven or more skin temperature measurement sites, including the hand and foot. We conclude that calculation of a reliable mean skin temperature must involve more than seven skin temperature measurement sites regardless of ambient temperature. Optimal sites for skin temperature measurement are proposed for various formulas.

  12. Infrared thermography based studies on mobile phone induced heating

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Bagavathiappan, S.; Soumya, C.; Jayakumar, T.; Philip, John

    2015-07-01

    Here, we report the skin temperature rise due to the absorption of radio frequency (RF) energy from three handheld mobile phones using infrared thermography technique. Experiments are performed under two different conditions, viz. when the mobile phones are placed in soft touch with the skin surface and away from the skin surface. Additionally, the temperature rise of mobile phones during charging, operation and simultaneous charging and talking are monitored under different exposure conditions. It is observed that the temperature of the cheek and ear regions monotonically increased with time during the usage of mobile phones and the magnitude of the temperature rise is higher for the mobile phone with higher specific absorption rate. The increase in skin temperature is higher when the mobile phones are in contact with the skin surface due to the combined effect of absorption of RF electromagnetic power and conductive heat transfer. The increase in the skin temperature in non-contact mode is found to be within the safety limit of 1 °C. The measured temperature rise is in good agreement with theoretical predictions. The empirical equation obtained from the temperature rise on the cheek region of the subjects correlates well with the specific absorption rate of the mobile phones. Our study suggests that the use of mobile phones in non-contact mode can significantly lower the skin temperature rise during its use and hence, is safer compared to the contact mode.

  13. Measuring and Estimating Normalized Contrast in Infrared Flash Thermography

    NASA Technical Reports Server (NTRS)

    Koshti, Ajay M.

    2013-01-01

    Infrared flash thermography (IRFT) is used to detect void-like flaws in a test object. The IRFT technique involves heating up the part surface using a flash of flash lamps. The post-flash evolution of the part surface temperature is sensed by an IR camera in terms of pixel intensity of image pixels. The IR technique involves recording of the IR video image data and analysis of the data using the normalized pixel intensity and temperature contrast analysis method for characterization of void-like flaws for depth and width. This work introduces a new definition of the normalized IR pixel intensity contrast and normalized surface temperature contrast. A procedure is provided to compute the pixel intensity contrast from the camera pixel intensity evolution data. The pixel intensity contrast and the corresponding surface temperature contrast differ but are related. This work provides a method to estimate the temperature evolution and the normalized temperature contrast from the measured pixel intensity evolution data and some additional measurements during data acquisition.

  14. Remote monitoring of breathing dynamics using infrared thermography

    PubMed Central

    Pereira, Carina Barbosa; Yu, Xinchi; Czaplik, Michael; Rossaint, Rolf; Blazek, Vladimir; Leonhardt, Steffen

    2015-01-01

    An atypical or irregular respiratory frequency is considered to be one of the earliest markers of physiological distress. In addition, monitoring of this vital parameter plays a major role in diagnosis of respiratory disorders, as well as in early detection of sudden infant death syndrome. Nevertheless, the current measurement modalities require attachment of sensors to the patient’s body, leading to discomfort and stress. The current paper presents a new robust algorithm to remotely monitor breathing rate (BR) by using thermal imaging. This approach permits to detect and to track the region of interest (nose) as well as to estimate BR. In order to study the performance of the algorithm, and its robustness against motion and breathing disorders, three different thermal recordings of 11 healthy volunteers were acquired (sequence 1: normal breathing; sequence 2: normal breathing plus arbitrary head movements; and sequence 3: sequence of specific breathing patterns). Thoracic effort (piezoplethysmography) served as “gold standard” for validation of our results. An excellent agreement between estimated BR and ground truth was achieved. Whereas the mean correlation for sequence 1–3 were 0.968, 0.940 and 0.974, the mean absolute BR errors reached 0.33, 0.55 and 0.96 bpm (breaths per minute), respectively. In brief, this work demonstrates that infrared thermography is a promising, clinically relevant alternative for the currently available measuring modalities due to its performance and diverse remarkable advantages. PMID:26601003

  15. International standards for pandemic screening using infrared thermography

    NASA Astrophysics Data System (ADS)

    Pascoe, D. D.; Ring, E. F.; Mercer, J. B.; Snell, J.; Osborn, D.; Hedley-Whyte, J.

    2010-03-01

    The threat of a virulent strain of influenza, severe acute respiratory syndrome (SARS), tuberculosis, H1N1/A virus (swine flu) and possible mutations are a constant threat to global health. Implementation of pandemic infrared thermographic screening is based on the detection of febrile temperatures (inner canthus of the eyes) that are correlated with an infectious disease. Previous attempts at pandemic thermal screening have experienced problems (e.g. SARS outbreak, Singapore 2003) associated with the deployment plan, implementation and operation of the screening thermograph. Since this outbreak, the International Electrotechnical Commission has developed international standards that set minimum requirements for thermographic system fever screening and procedures that insure reliable and reproducible measurements. These requirements are published in IEC 80601-2-59:2008, Medical electrical equipment - Part 2-59: Particular requirements for the basic safety and essential performance of screening thermographs for human febrile temperature screening. The International Organization for Standardization has developed ISO/TR 13154:2009, Medical Electrical Equipment - which provides deployment, implementation and operational guidelines for identifying febrile humans using a screening thermograph. These new standards includes recommendations for camera calibrations, use of black body radiators, view field, focus, pixels within measurement site, image positioning, and deployment locations. Many current uses of thermographic screening at airports do not take into account critical issues addressed in the new standard, and are operating below the necessary effectiveness and efficiency. These documents, related thermal research, implications for epidemiology screening, and the future impact on medical thermography are discussed.

  16. Automated diagnosis of dry eye using infrared thermography images

    NASA Astrophysics Data System (ADS)

    Acharya, U. Rajendra; Tan, Jen Hong; Koh, Joel E. W.; Sudarshan, Vidya K.; Yeo, Sharon; Too, Cheah Loon; Chua, Chua Kuang; Ng, E. Y. K.; Tong, Louis

    2015-07-01

    Dry Eye (DE) is a condition of either decreased tear production or increased tear film evaporation. Prolonged DE damages the cornea causing the corneal scarring, thinning and perforation. There is no single uniform diagnosis test available to date; combinations of diagnostic tests are to be performed to diagnose DE. The current diagnostic methods available are subjective, uncomfortable and invasive. Hence in this paper, we have developed an efficient, fast and non-invasive technique for the automated identification of normal and DE classes using infrared thermography images. The features are extracted from nonlinear method called Higher Order Spectra (HOS). Features are ranked using t-test ranking strategy. These ranked features are fed to various classifiers namely, K-Nearest Neighbor (KNN), Nave Bayesian Classifier (NBC), Decision Tree (DT), Probabilistic Neural Network (PNN), and Support Vector Machine (SVM) to select the best classifier using minimum number of features. Our proposed system is able to identify the DE and normal classes automatically with classification accuracy of 99.8%, sensitivity of 99.8%, and specificity if 99.8% for left eye using PNN and KNN classifiers. And we have reported classification accuracy of 99.8%, sensitivity of 99.9%, and specificity if 99.4% for right eye using SVM classifier with polynomial order 2 kernel.

  17. Low-velocity impact damage characterization of carbon fiber reinforced polymer (CFRP) using infrared thermography

    NASA Astrophysics Data System (ADS)

    Li, Yin; Zhang, Wei; Yang, Zheng-wei; Zhang, Jin-yu; Tao, Sheng-jie

    2016-05-01

    Carbon fiber reinforced polymer (CFRP) after low-velocity impact is detected using infrared thermography, and different damages in the impacted composites are analyzed in the thermal maps. The thermal conductivity under pulse stimulation, frictional heating and thermal conductivity under ultrasonic stimulation of CFRP containing low-velocity impact damage are simulated using numerical simulation method. Then, the specimens successively exposed to the low-velocity impact are respectively detected using the pulse infrared thermography and ultrasonic infrared thermography. Through the numerical simulation and experimental investigation, the results obtained show that the combination of the above two detection methods can greatly improve the capability for detecting and evaluating the impact damage in CFRP. Different damages correspond to different infrared thermal images. The delamination damage, matrix cracking and fiber breakage are characterized as the block-shape hot spot, line-shape hot spot, and

  18. Using infrared thermography to evaluate the injuries of cold-stored guava.

    PubMed

    Gonçalves, Bárbara Jordana; Giarola, Tales Márcio de Oliveira; Pereira, Daniele Fernanda; Vilas Boas, Eduardo Valério de Barros; de Resende, Jaime Vilela

    2016-02-01

    This study aimed to identify using the infrared (IR) thermography data the injuries of guavas during cooling and storage at different temperatures. Three experiments were performed at three different temperatures with one storage time. The first experiment was done with static air in a refrigerator at 5 °C, the second experiment was conducted in a tunnel with forced air at 10 °C, and the third experiment was conducted in an air conditioned environment at 20 °C. Mechanical injuries caused by the impact of a pendulum were induced on guava surfaces. The surface temperatures were obtained for bruised and sound tissues during cooling and storage using an Infrared (IR) camera. With thermography, it was possible to distinguish the injured tissues of the fruits that were unaffected at temperatures of 5, 10 and 20 °C in first hours of cooling. The results suggest that the storage of guava fruits at 5 °C in static air resulted in cold-induced injury, while storage at 20 °C resulted in an altered activity pattern. The stored guava fruits were analyzed for mass loss, firmness, color, total sugars, total pectin and solubility. The parameters values were lower during the forced-air cooling and storage at 5 and 10 °C. When stored at 20 °C, there was fruit maturation that caused tissue softening, which makes the fruits more susceptible to deterioration and thermographic readings showed opposite trends.

  19. Active thermography in qualitative evaluation of protective materials.

    PubMed

    Gralewicz, Grzegorz; Wiecek, Bogusław

    2009-01-01

    This is a study of the possibilities of a qualitative evaluation of protective materials with active thermography. It presents a simulation of a periodic excitation of a multilayer composite material. Tests were conducted with lock-in thermography on Kevlar composite consisting of 16 layers of Kevlar fabric reinforced with formaldehyde resin with implanted delamination defects. Lock-in thermography is a versatile tool for nondestructive evaluation. It is a fast, remote and nondestructive procedure. Hence, it was used to detect delaminations in the composite structure of materials used in the production of components designed for personal protection. This method directly contributes to an improvement in safety.

  20. Comparisons of Three Indicators for Frey's Syndrome: Subjective Symptoms, Minor's Starch Iodine Test, and Infrared Thermography

    PubMed Central

    Choi, Hyo Geun; Kwon, Sae Young; Won, Jung Youn; Yoo, Seung Woo; Lee, Min Gu; Kim, Si Whan

    2013-01-01

    Objectives To correlate Frey's syndrome with subjective symptoms, Minor's starch iodine test results, and infrared thermography measurements, and to discuss the utility of thermography as a quantitative diagnostic method. Methods This study included 59 patients who underwent unilateral parotidectomy. A subjective clinical questionnaire and an objective Minor's starch iodine test were performed to evaluate the incidence of Frey's syndrome. Infrared thermography was performed, and the subjects were divided into seven groups according to the temperature differences between operated and unoperated sites. The thermal differences were correlated with the results from Minor's starch iodine test and the subjective symptoms questionnaire. Results Of the 59 patients, 20 patients (33.9%) reported subjective symptoms after eating; 30 patients (50.8%) tested positive for Minor's starch iodine test, 19 patients (63.3%) of which reported subjective symptoms. Of the 29 patients who were negative for the iodine test, 2 patients (6.9%) reported subjective symptoms. Thus, subjective symptoms were well correlated with Minor's starch iodine test (r=0.589, P<0.001). As the thermal differences with infrared thermography increased, the number of patients with subjective symptoms increased (χ2=22.5, P<0.001). Using infrared thermography, the mean temperature difference in the positive group for the iodine test was 0.82℃±0.26℃, and that in the negative group was 0.10℃±0.47℃. With increased thermal differences, more patients showed positivity in the iodine test (χ2=29.9, P<0.001). Conclusion Subjective symptoms, Minor's starch iodine test, and infrared thermography are well correlated with one another. Quantitative thermography provides clues for the wide variation in the incidence of Frey's syndrome, and could be a useful method for diagnosing and studying Frey's syndrome. PMID:24353866

  1. Infrared thermography for laser-based powder bed fusion additive manufacturing processes

    NASA Astrophysics Data System (ADS)

    Moylan, Shawn; Whitenton, Eric; Lane, Brandon; Slotwinski, John

    2014-02-01

    Additive manufacturing (AM) has the potential to revolutionize discrete part manufacturing, but improvements in processing of metallic materials are necessary before AM will see widespread adoption. A better understanding of AM processes, resulting from physics-based modeling as well as direct process metrology, will form the basis for these improvements. Infrared (IR) thermography of AM processes can provide direct process metrology, as well as data necessary for the verification of physics-based models. We review selected works examining how IR thermography was implemented and used in various powder-bed AM processes. This previous work, as well as significant experience at the National Institute of Standards and Technology in temperature measurement and IR thermography for machining processes, shapes our own research in AM process metrology with IR thermography. We discuss our experimental design, as well as plans for future IR measurements of a laser-based powder bed fusion AM process.

  2. Infrared thermography for laser-based powder bed fusion additive manufacturing processes

    SciTech Connect

    Moylan, Shawn; Whitenton, Eric; Lane, Brandon; Slotwinski, John

    2014-02-18

    Additive manufacturing (AM) has the potential to revolutionize discrete part manufacturing, but improvements in processing of metallic materials are necessary before AM will see widespread adoption. A better understanding of AM processes, resulting from physics-based modeling as well as direct process metrology, will form the basis for these improvements. Infrared (IR) thermography of AM processes can provide direct process metrology, as well as data necessary for the verification of physics-based models. We review selected works examining how IR thermography was implemented and used in various powder-bed AM processes. This previous work, as well as significant experience at the National Institute of Standards and Technology in temperature measurement and IR thermography for machining processes, shapes our own research in AM process metrology with IR thermography. We discuss our experimental design, as well as plans for future IR measurements of a laser-based powder bed fusion AM process.

  3. Mapping the body surface temperature of cattle by infrared thermography.

    PubMed

    Salles, Marcia Saladini Vieira; da Silva, Suelen Corrêa; Salles, Fernando André; Roma, Luiz Carlos; El Faro, Lenira; Bustos Mac Lean, Priscilla Ayleen; Lins de Oliveira, Celso Eduardo; Martello, Luciane Silva

    2016-12-01

    Infrared thermography (IRT) is an alternative non-invasive method that has been studied as a tool for identifying many physiological and pathological processes related to changes in body temperature. The objective of the present study was to evaluate the body surface temperature of Jersey dairy cattle in a thermoneutral environment in order to contribute to the determination of a body surface temperature pattern for animals of this breed in a situation of thermal comfort. Twenty-four Jersey heifers were used over a period of 35 days at APTA Brazil. Measurements were performed on all animals, starting with the physiological parameters. Body surface temperature was measured by IRT collecting images in different body regions: left and right eye area, right and left eye, caudal left foreleg, cranial left foreleg, right and left flank, and forehead. High correlations were observed between temperature and humidity index (THI) and right flank, left flank and forehead temperatures (0.85, 0.81, and 0.81, respectively). The IRT variables that exhibited the five highest correlation coefficients in principal component 1 were, in decreasing order: forehead (0.90), right flank (0.87), left flank (0.84), marker 1 caudal left foreleg (0.83), marker 2 caudal left foreleg (0.74). The THI showed a high correlation coefficient (0.88) and moderate to low correlations were observed for the physiological variables rectal temperature (0.43), and respiratory frequency (0.42). The thermal profile obtained indicates a surface temperature pattern for each region studied in a situation of thermal comfort and may contribute to studies investigating body surface temperature. Among the body regions studied, IRT forehead temperature showed the highest association with rectal temperature, and forehead and right and left flank temperatures are strongly associated with THI and may be adopted in future studies on thermoregulation and body heat production.

  4. Using aerial infrared thermography to detect utility theft of service

    NASA Astrophysics Data System (ADS)

    Stockton, Gregory R.; Lucas, R. Gillem

    2012-06-01

    Natural gas and electric utility companies, public utility commissions, consumer advocacy groups, city governments, state governments and the federal government United States continue to turn a blind eye towards utility energy theft of service which we conservatively estimate is in excess of 10 billion a year. Why? Many in the United States have exhausted their unemployment benefits. The amounts for federal funding for low income heating assistance programs (LIHEAP) funds were cut by nearly 40% for 2012 to 3.02 billion. "At peak funding ($5.1 billion in 2009), the program was national in scale but still only had enough resources to support roughly 1/4 of the eligible households.i" Contributions to charities are down and the number of families below the poverty line who are unable to pay to heat their houses continues to rise. Many of the less fortunate in our society now consider theft and fraud to be an attractive option for their supply of natural gas and/or electricity. A record high mild winter in 2011-2012 coupled with 10-year low natural gas prices temporarily obscured the need for low income heating assistance programs (LIHEAPs) from the news and federal budgets, but cold winters will return. The proliferation of smart meters and automated meter infrastructures across our nation can do little to detect energy theft because the thieves can simply by-pass the meters, jumper around the meters and/or steal meters from abandoned houses and use them. Many utility systems were never set-up to stop these types of theft. Even with low-cost per identified thief method using aerial infrared thermography, utilities continue to ignore theft detection.

  5. Interference filters as an enhancement tool for infrared thermography in humidity studies of building elements

    NASA Astrophysics Data System (ADS)

    Gayo, E.; de Frutos, J.

    1997-06-01

    In the present work, the utility of infrared thermography applied to the study of moisture in builiding materials or in buildings (including those cases in which the water content is very high) is shown. Moreover, an increase in the information content of the thermal image by the use of suitable interference filters is demonstrated. The use of such filters allows us to determine the kind of hydric process. In the present work, different examples are given illustrating the use of infrared thermography (with and without interference filters) when moisture movement is studied.

  6. Infrared thermography as a diagnostic tool to indicate sick-house-syndrome: a case-study

    NASA Astrophysics Data System (ADS)

    Ljungberg, Sven-Ake

    1996-03-01

    Every third child and many adults in Sweden have allergic reactions caused by indoor environmental problems. A lot of buildings constructed during the building-boom period of 1950 - 1990 expose the sick-house-syndrome, due to built-in moisture problems and poor ventilation performance of the building. Leaky building construction, transport of humid air condensing on thermal bridges within the construction gives rise to a humid environment, and forms a base for a microbial deterioration process of organic materials, with emissions hazardous for human health. So far there are no universal and cost efficient techniques or methods developed which could be used to reveal the sick-house-syndrome. In this paper we present the results of a case-study of the sick-house-syndrome, and an investigation concept with a combination of different techniques and methods to detect and to map underlying factors that form the base for microbial activities. The concept includes mobile and indoor thermography, functional control of ventilation systems, tracer gas techniques for measurement of air flow exchange rate in different rooms, microbial investigation of emissions, field inspections within the building construction and the building envelope, and medical investigation of the health status of the people working in the building. Mobile thermography of the exterior facades has been performed with a longwave AGEMA THV 900, respectively THV 1000 infrared system, during the period December 1994 - June 1995, at different and similar weather and radiation conditions, and with the building pressurized at one accession. Indoor thermography has been performed with a shortwave AGEMA THV 470 system, for a selection of objects/surfaces with thermal deviations, indicated in thermograms from the different mobile thermographic surveys. Functional control was performed for the ventilation systems, and air flow rates were measured using tracer gas technique for a selection of rooms with different

  7. Infrared thermography at EDF: common technique for high-voltage lines but new in monitoring and diagnosis of PWR plant components

    NASA Astrophysics Data System (ADS)

    Provost, Daniel

    1996-03-01

    Infrared thermography is a remarkable aid in maintenance, and has been used for a number of years in testing high-voltage lines and transformer substations. Electricite de France (EDF) has developed a special infrared thermography system for this type of application. Until recently, use of IRT in both fossil and nuclear power plants was only sporadic and depended on the interest shown in the technique by individual maintenance managers. In power stations, it was primarily used for tests on switchyards, electrical control cabinets and insulation. The General Engineering Department of the EDF Generation and Transmission Division was responsible for assessing new equipment and studying special development requirements as they arose. Routine infrared thermography tests were performed by two teams from the Division, one handling northern France and the other southern France. Today, infrared thermography has become a fully-fledged monitoring and diagnosis tool in its own right, and related activities are being reorganized accordingly. Its recent success can be attributed to a number of factors: more high-powered IRT techniques, valuable feedback from American utility companies, and technical and economic assessments conducted by EDF over the last two years on equipment such as electrical and mechanical components, valves and insulation. EDF's reorganization of infrared thermography activities will begin with an overview of the resources now existing within the company. This inventory will be carried out by the General Engineering Department. At the same time, a report will be drawn up bearing on IRT testing over the last decade in conventional and nuclear power plants in France and the United States. Lastly, EDF will draw up a list of components to be monitored in this way, essentially on the basis of RCM studies. These measures will provide power plants with a catalogue of infrared thermography applications for specific component/failure combinations.

  8. Calibration and Evaluation of Ultrasound Thermography Using Infrared Imaging.

    PubMed

    Hsiao, Yi-Sing; Deng, Cheri X

    2016-02-01

    Real-time monitoring of the spatiotemporal evolution of tissue temperature is important to ensure safe and effective treatment in thermal therapies including hyperthermia and thermal ablation. Ultrasound thermography has been proposed as a non-invasive technique for temperature measurement, and accurate calibration of the temperature-dependent ultrasound signal changes against temperature is required. Here we report a method that uses infrared thermography for calibration and validation of ultrasound thermography. Using phantoms and cardiac tissue specimens subjected to high-intensity focused ultrasound heating, we simultaneously acquired ultrasound and infrared imaging data from the same surface plane of a sample. The commonly used echo time shift-based method was chosen to compute ultrasound thermometry. We first correlated the ultrasound echo time shifts with infrared-measured temperatures for material-dependent calibration and found that the calibration coefficient was positive for fat-mimicking phantom (1.49 ± 0.27) but negative for tissue-mimicking phantom (-0.59 ± 0.08) and cardiac tissue (-0.69 ± 0.18°C-mm/ns). We then obtained the estimation error of the ultrasound thermometry by comparing against the infrared-measured temperature and revealed that the error increased with decreased size of the heated region. Consistent with previous findings, the echo time shifts were no longer linearly dependent on temperature beyond 45°C-50°C in cardiac tissues. Unlike previous studies in which thermocouples or water bath techniques were used to evaluate the performance of ultrasound thermography, our results indicate that high-resolution infrared thermography is a useful tool that can be applied to evaluate and understand the limitations of ultrasound thermography methods.

  9. Photothermal and infrared thermography characterizations of thermal diffusion in hydroxyapatite materials

    NASA Astrophysics Data System (ADS)

    Bante-Guerra, J.; Conde-Contreras, M.; Trujillo, S.; Martinez-Torres, P.; Cruz-Jimenez, B.; Quintana, P.; Alvarado-Gil, J. J.

    2009-02-01

    Non destructive analysis of hydroxyapatite materials is an active research area mainly in the study of dental pieces and bones due to the importance these pieces have in medicine, archeology, dentistry, forensics and anthropology. Infrared thermography and photothermal techniques constitute highly valuable tools in those cases. In this work the quantitative analysis of thermal diffusion in bones is presented. The results obtained using thermographic images are compared with the ones obtained from the photothermal radiometry. Special emphasis is done in the analysis of samples with previous thermal damage. Our results show that the treatments induce changes in the physical properties of the samples. These results could be useful in the identification of the agents that induced modifications of unknown origin in hydroxyapatite structures.

  10. Infrared contrast data analysis method for quantitative measurement and monitoring in flash infrared thermography

    NASA Astrophysics Data System (ADS)

    Koshti, Ajay M.

    2015-04-01

    The paper provides information on a new infrared (IR) image contrast data post-processing method that involves converting raw data to normalized contrast versus time evolutions from the flash infrared thermography inspection video data. Thermal measurement features such as peak contrast, peak contrast time, persistence time, and persistence energy are calculated from the contrast evolutions. In addition, simulation of the contrast evolution is achieved through calibration on measured contrast evolutions from many flat bottom holes in a test plate of the subject material. The measurement features are used to monitor growth of anomalies and to characterize the void-like anomalies. The method was developed to monitor and analyze void-like anomalies in reinforced carbon-carbon (RCC) materials used on the wing leading edge of the NASA Space Shuttle Orbiters, but the method is equally applicable to other materials. The thermal measurement features relate to the anomaly characteristics such as depth and size. Calibration of the contrast is used to provide an assessment of the anomaly depth and width which correspond to the depth and diameter of the equivalent flat bottom hole (EFBH) from the calibration data. An edge detection technique called the half-max is used to measure width and length of the anomaly. Results of the half-max width and the EFBH diameter are compared with actual widths to evaluate utility of IR Contrast method. Some thermal measurements relate to gap thickness of the delaminations. Results of IR Contrast method on RCC hardware are provided. Keywords: normalized contrast, flash infrared thermography.

  11. Non-destructive Testing by Infrared Thermography Under Random Excitation and ARMA Analysis

    NASA Astrophysics Data System (ADS)

    Bodnar, J. L.; Nicolas, J. L.; Candoré, J. C.; Detalle, V.

    2012-11-01

    Photothermal thermography is a non-destructive testing (NDT) method, which has many applications in the field of control and characterization of thin materials. This technique is usually implemented under CW or flash excitation. Such excitations are not adapted for control of fragile materials or for multi-frequency analysis. To allow these analyses, in this article, the use of a new control mode is proposed: infrared thermography under random excitation and auto regressive moving average analysis. First, the principle of this NDT method is presented. Then, the method is shown to permit detection, with low energy constraints, of detachments situated in mural paintings.

  12. Developing written inspection procedures for thermal/infrared thermography

    SciTech Connect

    Snell, J.

    1996-12-31

    Written inspection procedures are essential to acquiring valid data on a repeatable basis. They are also vital to the safety of the thermographer, and may, for that reason alone, be required by a company. Many thermographers are working with no written procedures. To date only a few of the necessary procedures have been developed by recognized standards organizations. The lack of procedures is limiting the use of thermography. Where thermography is being used without them, results are often less than optimum. This paper will (1) survey existing procedures and standards; (2) discuss current efforts by standards organizations to develop standards and procedures; and (3) present a general methodology from which written inspection procedures can be developed for many thermographic inspections.

  13. Active thermography inspection of protective glass contamination on laser scanning heads.

    PubMed

    Skala, J; Svantner, M; Tesar, J; Franc, A

    2016-12-01

    Industrial lasers are an expanding technology of welding and other materials processing. Lasers with optical scanning heads are often used, as these provide more versatility, accuracy, and speed. The output part of the scanning head is covered by a protective glass, which might get contaminated by various particles from the laser processing. This decreases the transmissivity of the glass, and it can affect the production quality. The contamination needs to be checked regularly, but a visual inspection might not always be effective. This paper proposes two alternative methods of inspecting the protective glass: flash-pulse active thermography, and laser active thermography. They are based on the thermal excitation of the glass and measuring the response with an infrared camera. The experimental setup and practical results are described and the advantages and disadvantages are discussed. The presented methods are proven to be effective in detecting the contamination of the glass.

  14. Modeling of the ITER-like wide-angle infrared thermography view of JET

    SciTech Connect

    Aumeunier, M.-H.; Firdaouss, M.; Travere, J.-M.; Loarer, T.; Gauthier, E.; Martin, V.; Chabaud, D.; Humbert, E.; Collaboration: JET-EFDA Contributors

    2012-10-15

    Infrared (IR) thermography systems are mandatory to ensure safe plasma operation in fusion devices. However, IR measurements are made much more complicated in metallic environment because of the spurious contributions of the reflected fluxes. This paper presents a full predictive photonic simulation able to assess accurately the surface temperature measurement with classical IR thermography from a given plasma scenario and by taking into account the optical properties of PFCs materials. This simulation has been carried out the ITER-like wide angle infrared camera view of JET in comparing with experimental data. The consequences and the effects of the low emissivity and the bidirectional reflectivity distribution function used in the model for the metallic PFCs on the contribution of the reflected flux in the analysis are discussed.

  15. Quantitative detection of defects based on Markov-PCA-BP algorithm using pulsed infrared thermography technology

    NASA Astrophysics Data System (ADS)

    Tang, Qingju; Dai, Jingmin; Liu, Junyan; Liu, Chunsheng; Liu, Yuanlin; Ren, Chunping

    2016-07-01

    Quantitative detection of debonding defects' diameter and depth in TBCs has been carried out using pulsed infrared thermography technology. By combining principal component analysis with neural network theory, the Markov-PCA-BP algorithm was proposed. The principle and realization process of the proposed algorithm was described. In the prediction model, the principal components which can reflect most characteristics of the thermal wave signal were set as the input, and the defect depth and diameter was set as the output. The experimental data from pulsed infrared thermography tests of TBCs with flat bottom hole defects was selected as the training and testing sample. Markov-PCA-BP predictive system was arrived, based on which both the defect depth and diameter were identified accurately, which proved the effectiveness of the proposed method for quantitative detection of debonding defects in TBCs.

  16. Detection and Characterization of Boundary-Layer Transition in Flight at Supersonic Conditions Using Infrared Thermography

    NASA Technical Reports Server (NTRS)

    Banks, Daniel W.

    2008-01-01

    Infrared thermography is a powerful tool for investigating fluid mechanics on flight vehicles. (Can be used to visualize and characterize transition, shock impingement, separation etc.). Updated onboard F-15 based system was used to visualize supersonic boundary layer transition test article. (Tollmien-Schlichting and cross-flow dominant flow fields). Digital Recording improves image quality and analysis capability. (Allows accurate quantitative (temperature) measurements, Greater enhancement through image processing allows analysis of smaller scale phenomena).

  17. AN EVALUATION OF INFRARED THERMOGRAPHY FOR DETECTION OF BUMBLEFOOT (PODODERMATITIS) IN PENGUINS.

    PubMed

    Duncan, Ann E; Torgerson-White, Lauri L; Allard, Stephanie M; Schneider, Tom

    2016-06-01

    The objective of this study was to evaluate infrared thermography as a noninvasive screening tool for detection of pododermatitis during the developing and active stages of disease in three species of penguins: king penguin (Aptenodytes patagonicus) , macaroni penguin (Eudyptes chrysolophus), and rockhopper penguin (Eudyptes chrysocome). In total, 67 penguins were examined every 3 mo over a 15-mo period. At each exam, bumblefoot lesions were characterized and measured, and a timed series of thermal images were collected over a 4-min period. Three different methods were compared for analysis of thermograms. Feet with active lesions that compromise the surface of the foot were compared to feet with inactive lesions and no lesions. The hypothesis was that feet with active lesions would have warmer surface temperatures than the other conditions. Analysis of the data showed that although feet with active bumblefoot lesions are warmer than feet with inactive or no lesions, the variability seen in each individual penguin from one exam day to the next and the overlap seen between temperatures from each condition made thermal imaging an unreliable tool for detection of bumblefoot in the species studied.

  18. Scrotal infrared digital thermography in assessment of varicocele--pilot study to assess diagnostic criteria.

    PubMed

    Kulis, T; Kolaric, D; Karlovic, K; Knezevic, M; Antonini, S; Kastelan, Z

    2012-05-01

    The aim of this study was to assess scrotal thermography in diagnostics of varicocele and suggest potential diagnostic criteria. Twelve patients with clinically diagnosed varicocele were examined with scrotal infrared digital thermography, physical examination and ultrasound/doppler. The main outcome measure was evaluation of thermography diagnostic criteria for varicocele. Mean temperature at left pampiniform plexus was ≥ 34 °C in 83%, and at right pampiniform plexus in all cases was ≤ 34 °C. In 92% of patients, temperature at the left testicle was ≥ 32 °C, whereas at the right testicle it was >32 °C in 50% patients. Temperatures between left and right pampiniform plexus and between left and right testicle were significantly different with P < 0.0001 and P < 0.006 respectively. In all patients, temperature difference between pampiniform plexuses was ≥ 0.6 °C. In 92% of patients, temperature at left pampiniform plexus was equal or higher to thigh temperature with the mean temperature difference of 1.1 ± 1.1 °C. Temperature at right pampiniform plexus was colder than the thigh in 92% of patients. This study suggests diagnostic criteria of five thermographic signs to easily diagnose varicocele. Scrotal thermography presents feasible, short and low cost diagnostic method for varicocele. Further study on a larger number of patients and healthy participants is needed to evaluate sensitivity and specificity of this method.

  19. Infrared Thermography to Evaluate Heat Tolerance in Different Genetic Groups of Lambs

    PubMed Central

    McManus, Concepta; Bianchini, Eliandra; Paim, Tiago do Prado; de Lima, Flavia Gontijo; Braccini Neto, José; Castanheira, Marlos; Esteves, Geisa Isilda Ferreira; Cardoso, Caio Cesar; Dalcin, Vanessa Calderaro

    2015-01-01

    Heat stress is considered a limiting factor for sheep production. We used information from physiological characteristics linked to heat tolerance to determine whether infrared thermography temperatures were able to separate groups of animals and determine the most important variables in this differentiation. Forty-eight four-month-old male lambs from eight genetic groups were used. Physiological (rectal temperature–RT, heart rate–HR, respiratory rate–RR) and blood traits, infrared thermography temperatures, heat tolerance indices, body measurements, weight and carcass traits were measured. Statistical analyses included variance, correlations, factor, discrimination and regression. Observing the correlations between physiological characteristics (RT, RR and HR) with temperatures measured by infrared thermography, regions for further studies should include the mean temperature of flank, nose and rump. Results show that there are strong relationships between thermograph measurements and RR, RT and HR in lambs, which are suggested to be directly correlated with heat tolerance capacity of the different genetic groups evaluated in this study. The assessment of body surface temperature measured by the thermograph could be used as a noninvasive tool to assess heat tolerance of the animals. PMID:26193274

  20. Infrared Thermography to Evaluate Heat Tolerance in Different Genetic Groups of Lambs.

    PubMed

    McManus, Concepta; Bianchini, Eliandra; Paim, Tiago do Prado; de Lima, Flavia Gontijo; Neto, José Braccini; Castanheira, Marlos; Esteves, Geisa Isilda Ferreira; Cardoso, Caio Cesar; Dalcin, Vanessa Calderaro

    2015-07-16

    Heat stress is considered a limiting factor for sheep production. We used information from physiological characteristics linked to heat tolerance to determine whether infrared thermography temperatures were able to separate groups of animals and determine the most important variables in this differentiation. Forty-eight four-month-old male lambs from eight genetic groups were used. Physiological (rectal temperature-RT, heart rate-HR, respiratory rate-RR) and blood traits, infrared thermography temperatures, heat tolerance indices, body measurements, weight and carcass traits were measured. Statistical analyses included variance, correlations, factor, discrimination and regression. Observing the correlations between physiological characteristics (RT, RR and HR) with temperatures measured by infrared thermography, regions for further studies should include the mean temperature of flank, nose and rump. Results show that there are strong relationships between thermograph measurements and RR, RT and HR in lambs, which are suggested to be directly correlated with heat tolerance capacity of the different genetic groups evaluated in this study. The assessment of body surface temperature measured by the thermograph could be used as a noninvasive tool to assess heat tolerance of the animals.

  1. Application of Infrared Thermography as a Diagnostic Tool of Knee Osteoarthritis

    NASA Astrophysics Data System (ADS)

    Arfaoui, Ahlem; Bouzid, Mohamed Amine; Pron, Hervé; Taiar, Redha; Polidori, Guillaume

    This paper aimed to study the feasibility of application of infrared thermography to detect osteoarthritis of the knee and to compare the distribution of skin temperature between participants with osteoarthritis and those without pathology. All tests were conducted at LACM (Laboratory of Mechanical Stresses Analysis) and the gymnasium of the University of Reims Champagne Ardennes. IR thermography was performed using an IR camera. Ten participants with knee osteoarthritis and 12 reference healthy participants without OA participated in this study. Questionnaires were also used. The participants with osteoarthritis of the knee were selected on clinical examination and a series of radiographs. The level of pain was recorded by using a simple verbal scale (0-4). Infrared thermography reveals relevant disease by highlighting asymmetrical behavior in thermal color maps of both knees. Moreover, a linear evolution of skin temperature in the knee area versus time has been found whatever the participant group is in the first stage following a given effort. Results clearly show that the temperature can be regarded as a key parameter for evaluating pain. Thermal images of the knee were taken with an infrared camera. The study shows that with the advantage of being noninvasive and easily repeatable, IRT appears to be a useful tool to detect quantifiable patterns of surface temperatures and predict the singular thermal behavior of this pathology. It also seems that this non-intrusive technique enables to detect the early clinical manifestations of knee OA.

  2. Application of infrared lock-in thermography for the quantitative evaluation of bruises on pears

    NASA Astrophysics Data System (ADS)

    Kim, Ghiseok; Kim, Geon-Hee; Park, Jongmin; Kim, Dae-Yong; Cho, Byoung-Kwan

    2014-03-01

    An infrared lock-in thermography technique was adjusted for the detection of early bruises on pears. This mechanical damage is usually difficult to detect in the early stage after harvested using conventional visual sorting or CCD sensor-based imaging processing methods. We measured the thermal emission signals from pears using a highly sensitive mid-infrared thermal camera. These images were post-processed using a lock-in method that utilized the periodic thermal energy input to the pear. By applying the lock-in method to infrared thermography, the detection sensitivity and signal to noise ratio were enhanced because of the phase-sensitive narrow-band filtering effect. It was also found that the phase information of thermal emission from pears provides good metrics with which to identify quantitative information about both damage size and damage depth for pears. Additionally, a photothermal model was implemented to investigate the behavior of thermal waves on pears under convective conditions. Theoretical results were compared to experimental results. These results suggested that the proposed lock-in thermography technique and resultant phase information can be used to detect mechanical damage to fruit, especially in the early stage of bruising.

  3. Monitoring the fracture behavior in ceramic matrix composites by infrared thermography and acoustic emission

    NASA Astrophysics Data System (ADS)

    Dassios, Konstantinos G.; Kordatos, Evangelos Z.; Aggelis, Dimitris G.; Exarchos, Dimitris A.; Matikas, Theodore E.

    2014-04-01

    In this work an innovative methodology was employed for monitoring the fracture behavior in silicon carbide fiberreinforced ceramic matrix composites. This new methodology was based on the combined use of IR thermography and acoustic emission. Compact tension SiC/BMAS specimens were tested with unloading/reloading loops and the thermal dissipation due to crack propagation and other damage mechanisms was monitored by IR thermography. The accuracy of this technique was benchmarked by optical measurements of crack length. In addition, using acoustic emission descriptors, such as activity during the unloading part of the cycles, provided the critical level of damage accumulation in the material. Acoustic emission allowed to closely follow the actual crack growth monitored by IR thermography, enabling quantitative measurements.

  4. Neonatal infrared thermography imaging: Analysis of heat flux during different clinical scenarios

    NASA Astrophysics Data System (ADS)

    Abbas, Abbas K.; Heimann, Konrad; Blazek, Vladimir; Orlikowsky, Thorsten; Leonhardt, Steffen

    2012-11-01

    IntroductionAn accurate skin temperature measurement of Neonatal Infrared Thermography (NIRT) imaging requires an appropriate calibration process for compensation of external effects (e.g. variation of environmental temperature, variable air velocity or humidity). Although modern infrared cameras can perform such calibration, an additional compensation is required for highly accurate thermography. This compensation which corrects any temperature drift should occur during the NIRT imaging process. We introduce a compensation technique which is based on modeling the physical interactions within the measurement scene and derived the detected temperature signal of the object. Materials and methodsIn this work such compensation was performed for different NIRT imaging application in neonatology (e.g. convective incubators, kangaroo mother care (KMC), and an open radiant warmer). The spatially distributed temperatures of 12 preterm infants (average gestation age 31 weeks) were measured under these different infant care arrangements (i.e. closed care system like a convective incubator, and open care system like kangaroo mother care, and open radiant warmer). ResultsAs errors in measurement of temperature were anticipated, a novel compensation method derived from infrared thermography of the neonate's skin was developed. Moreover, the differences in temperature recording for the 12 preterm infants varied from subject to subject. This variation could be arising from individual experimental setting applied to the same region of interest over the neonate's body. The experimental results for the model-based corrections is verified over the selected patient group. ConclusionThe proposed technique relies on applying model-based correction to the measured temperature and reducing extraneous errors during NIRT. This application specific method is based on different heat flux compartments present in neonatal thermography scene. Furthermore, these results are considered to be

  5. The roles of vibration analysis and infrared thermography in monitoring air-handling equipment

    NASA Astrophysics Data System (ADS)

    Wurzbach, Richard N.

    2003-04-01

    Industrial and commercial building equipment maintenance has not historically been targeted for implementation of PdM programs. The focus instead has been on manufacturing, aerospace and energy industries where production interruption has significant cost implications. As cost-effectiveness becomes more pervasive in corporate culture, even office space and labor activities housed in large facilities are being scrutinized for cost-cutting measures. When the maintenance costs for these facilities are reviewed, PdM can be considered for improving the reliability of the building temperature regulation, and reduction of maintenance repair costs. An optimized program to direct maintenance resources toward a cost effective and pro-active management of the facility can result in reduced operating budgets, and greater occupant satisfaction. A large majority of the significant rotating machinery in a large building environment are belt-driven air handling units. These machines are often poorly designed or utilized within the facility. As a result, the maintenance staff typically find themselves scrambling to replace belts and bearings, going from one failure to another. Instead of the reactive-mode maintenance, some progressive and critical institutions are adopting predictive and proactive technologies of infrared thermography and vibration analysis. Together, these technologies can be used to identify design and installation problems, that when corrected, significantly reduce maintenance and increase reliability. For critical building use, such as laboratories, research facilities, and other high value non-industrial settings, the cost-benefits of more reliable machinery can contribute significantly to the operational success.

  6. Modelling and predicting hidden solder joint shape using active thermography and parametric numerical analysis

    NASA Astrophysics Data System (ADS)

    Giron Palomares, Jose Benjamin; Hsieh, Sheng-Jen

    2014-05-01

    A methodology based on active infrared thermography to study and characterize hidden solder joint shapes on a multi cover PCB assembly was investigated. A numerical model was developed to simulate the active thermography methodology and was proven to determine the grand average cooling rates with maximum errors of 8.85% (one cover) and 13.36% (two covers). A parametric analysis was performed by varying the number of covers, heat flux provided, and the amount of heating time. Grand average cooling rate distances among contiguous solder joint shapes, as well as solder joints discriminability, were determined to be directly proportional to heat flux, and inversely proportional to the number of covers and heating time. Finally, a mathematical model was developed to determine the appropriate total amount of energy needed to discriminate among hidden solder joints with a "good" discriminability for one and two covers, and a "regular" discriminability for up to five covers. The mathematical model was proven to predict the total amount of energy to achieve a "good" discriminability for one cover within a 10% of error with respect to the experimental active thermography model.

  7. Pulsed infrared thermography processing and defects edge detection using FCA and ACA

    NASA Astrophysics Data System (ADS)

    Yuanlin, Liu; Qingju, Tang; Chiwu, Bu; Chen, Mei; Pingshan, Wang; Jiansuo, Zang

    2015-09-01

    CFRP sheet with delamination defects was detected using pulsed infrared thermography. The principle of polynomial fitting the derivative time algorithm (FDA) and related coefficient algorithm (RCA) was described. A new polynomial fitting the derivative time-related coefficient algorithm (FCA) was formed by combining FDA and RCA, which improves the signal to noise (SNR) of feature images, and is benefit for the detection and identification of defects. The defects edge identification procedure using ant colony algorithm (ACA) is given, and the defect edge features in the infrared image have been extracted using ACA effectively.

  8. Infrared digital thermography of scrotum in early selection of progressive varicocele.

    PubMed

    Kulis, T; Knezevic, M; Karlovic, K; Kolaric, D; Antonini, S; Kastelan, Z

    2013-10-01

    Varicocele is frequent but correctable cause of male infertility. Varicocelectomy is the most commonly performed operative procedure for varicocele. Majority of varicocele patients do not have fertility problem, therefore surgical correction is not recommended in all prevalent cases. On the other hand, varicocele is a progressive condition in some cases and individual with varicocele is at risk for developing impairment which can ultimately lead to semen deterioration and consequent infertility. Selection of patients with varicocele that will progress and cause infertility is beyond our current diagnostic capabilities. Diagnostic assessment of varicocele depends on physical examination and scrotal ultrasound/doppler. Infrared digital thermography of scrotum is a non-invasive and objective diagnostic method for early varicocele detection by means of temperature measurement on the scrotal skin surface. The criteria for diagnostic use of scrotal thermography were recently presented. We hypothesize that the infrared digital thermography of scrotum could be the cornerstone in detection of varicoceles that tend to progress with impairment of semen quality and will require surgical correction, among all prevalent varicocele cases.

  9. Infrared thermography and ultrasonics to evaluate composite materials for aeronautical applications

    NASA Astrophysics Data System (ADS)

    Boccardi, S.; Boffa, N. D.; Carlomagno, G. M.; Maio, L.; Meola, C.; Ricci, F.

    2015-11-01

    The attention of this paper is focused on the suitability of two techniques: infrared thermography and ultrasonics to evaluate impact damaged carbon/epoxy specimens. The obtained results are compared by highlighting advantages and disadvantages of each technique, as well their limits in view of an integrated use. In this context, a crucial task may be to assess the extension of delamination caused by an impact event, which may ask one to guess between sound and damaged materials at the edge of the instrument background noise. To help fixing this problem, results obtained with either lock-in thermography, or an ultrasonic phased array system, are analysed with the aid of thermographic data collected during impact tests.

  10. A Novel Method for Extracting Respiration Rate and Relative Tidal Volume from Infrared Thermography

    PubMed Central

    Lewis, Gregory F.; Gatto, Rodolfo G.; Porges, Stephen W.

    2010-01-01

    In psychophysiological research, measurement of respiration has been dependent on transducers having direct contact with the participant. The current study provides empirical data demonstrating that a noncontact technology, infrared video thermography, can accurately estimate breathing rate and relative tidal volume across a range of breathing patterns. Video tracking algorithms were applied to frame-by-frame thermal images of the face to extract time series of nostril temperature and to generate breath-by-breath measures of respiration rate and relative tidal volume. The thermal indices of respiration were contrasted with criterion measures collected with inductance plethysmography. The strong correlations observed between the technologies demonstrate the potential use of facial video thermography as a noncontact technology to monitor respiration. PMID:21214587

  11. Assessment of anxiety in open field and elevated plus maze using infrared thermography.

    PubMed

    Lecorps, Benjamin; Rödel, Heiko G; Féron, Christophe

    2016-04-01

    Due to their direct inaccessibility, affective states are classically assessed by gathering concomitant physiological and behavioral measures. Although such a dual approach to assess emotional states is frequently used in different species including humans, the invasiveness of procedures for physiological recordings particularly in smaller-sized animals strongly restricts their application. We used infrared thermography, a non-invasive method, to assess physiological arousal during open field and elevated plus maze tests in mice. By measuring changes in surface temperature indicative of the animals' emotional response, we aimed to improve the inherently limited and still controversial information provided by behavioral parameters commonly used in these tests. Our results showed significant and consistent thermal responses during both tests, in accordance with classical physiological responses occurring in stressful situations. Besides, we found correlations between these thermal responses and the occurrence of anxiety-related behaviors. Furthermore, initial temperatures measured at the start of each procedure (open field, elevated plus maze), which can be interpreted as a measure of the animals' initial physiological arousal, predicted the levels of activity and of anxiety-related behaviors displayed during the tests. Our results stress the strong link between physiological correlates of emotions and behaviors expressed during unconditioned fear tests.

  12. Infrared dermal thermography on diabetic feet soles to predict ulcerations: a case study

    NASA Astrophysics Data System (ADS)

    Liu, Chanjuan; van der Heijden, Ferdi; Klein, Marvin E.; van Baal, Jeff G.; Bus, Sicco A.; van Netten, Jaap J.

    2013-03-01

    Diabetic foot ulceration is a major complication for patients with diabetes mellitus. If not adequately treated, these ulcers may lead to foot infection, and ultimately to lower extremity amputation, which imposes a major burden to society and great loss in health-related quality of life for patients. Early identification and subsequent preventive treatment have proven useful to limit the incidence of foot ulcers and lower extremity amputation. Thus, the development of new diagnosis tools has become an attractive option. The ultimate objective of our project is to develop an intelligent telemedicine monitoring system for frequent examination on patients' feet, to timely detect pre-signs of ulceration. Inflammation in diabetic feet can be an early and predictive warning sign for ulceration, and temperature has been proven to be a vicarious marker for inflammation. Studies have indicated that infrared dermal thermography of foot soles can be one of the important parameters for assessing the risk of diabetic foot ulceration. This paper covers the feasibility study of using an infrared camera, FLIR SC305, in our setup, to acquire the spatial thermal distribution on the feet soles. With the obtained thermal images, automated detection through image analysis was performed to identify the abnormal increased/decreased temperature and assess the risk for ulceration. The thermography for feet soles of patients with diagnosed diabetic foot complications were acquired before the ordinary foot examinations. Assessment from clinicians and thermography were compared and follow-up measurements were performed to investigate the prediction. A preliminary case study will be presented, indicating that dermal thermography in our proposed setup can be a screening modality to timely detect pre-signs of ulceration.

  13. Laser active thermography for non-destructive testing

    NASA Astrophysics Data System (ADS)

    Semerok, A.; Grisolia, C.; Fomichev, S. V.; Thro, P.-Y.

    2013-11-01

    Thermography methods have found their applications in different fields of human activity. The non-destructive feature of these methods along with the additional advantage by automated remote control and tests of nuclear installations without personnel attendance in the contaminated zone are of particular interest. Laser active pyrometry and laser lock-in thermography for in situ non-destructive characterization of micrometric layers on graphite substrates from European tokamaks were under extensive experimental and theoretical studies in CEA (France). The studies were aimed to obtain layer characterization with cross-checking the layer thermal contact coefficients determined by active laser pyrometry and lock-in thermography. The experimental installation comprised a Nd-YAG pulsed repetition rate laser (1 Hz - 10 kHz repetition rate frequency, homogeneous spot) and a home-made pyrometer system based on two pyrometers for the temperature measurements in 500 - 2600 K range. For both methods, the layer characterization was provided by the best fit of the experimental results and simulations. The layer thermal contact coefficients determined by both methods were quite comparable. Though there was no gain in the measurements accuracy, lock-in measurements have proved their advantage as being much more rapid. The obtained experimental and theoretical results are presented. Some practical applications and possible improvements of the methods are discussed.

  14. Passive and active thermography for in situ damage monitoring in woven composites during mechanical testing

    NASA Astrophysics Data System (ADS)

    Roche, J.-M.; Balageas, D.; Lamboul, B.; Bai, G.; Passilly, F.; Mavel, A.; Grail, G.

    2013-01-01

    The aim of the present paper is to highlight the contribution of both passive and active infrared thermography for in situ damage detection and monitoring in a 2D woven composite, during a mechanical testing constituted of multiple sequences of loadings and intermediate pauses. During the monotonic tensile loadings, damages such as matrix cracking and fiber-matrix debondings are monitored by passive thermography. Their thermal signatures are analyzed and the released heat, which is assumed to be a relevant index of their severity, is evaluated and correlated to the associated acoustic energies, simultaneously recorded. Finally, the contribution of the TSR (Thermographic Signal Reconstruction) advanced processing technique to provide a qualitative overview of the detected damages is underlined. As for the constant stress plateau levels, a nondestructive damage inspection of the tested specimen is carried out by pulsed thermography. The difficulties, due to the woven structure of the composite, in detecting any damage are put into relief. Once more, it is shown that the TSR technique can be useful.

  15. An assessment of skin temperature gradients in a tropical primate using infrared thermography and subcutaneous implants.

    PubMed

    Thompson, Cynthia L; Scheidel, Caleb; Glander, Kenneth E; Williams, Susan H; Vinyard, Christopher J

    2017-01-01

    Infrared thermography has become a useful tool to assess surface temperatures of animals for thermoregulatory research. However, surface temperatures are an endpoint along the body's core-shell temperature gradient. Skin and fur are the peripheral tissues most exposed to ambient thermal conditions and are known to serve as thermosensors that initiate thermoregulatory responses. Yet relatively little is known about how surface temperatures of wild mammals measured by infrared thermography relate to subcutaneous temperatures. Moreover, this relationship may differ with the degree that fur covers the body. To assess the relationship between temperatures and temperature gradients in peripheral tissues between furred and bare areas, we collected data from wild mantled howling monkeys (Alouatta palliata) in Costa Rica. We used infrared thermography to measure surface temperatures of the furred dorsum and bare facial areas of the body, recorded concurrent subcutaneous temperatures in the dorsum, and measured ambient thermal conditions via a weather station. Temperature gradients through cutaneous tissues (subcutaneous-surface temperature) and surface temperature gradients (surface-ambient temperature) were calculated. Our results indicate that there are differences in temperatures and temperature gradients in furred versus bare areas of mantled howlers. Under natural thermal conditions experienced by wild animals, the bare facial areas were warmer than temperatures in the furred dorsum, and cutaneous temperature gradients in the face were more variable than the dorsum, consistent with these bare areas acting as thermal windows. Cutaneous temperature gradients in the dorsum were more closely linked to subcutaneous temperatures, while facial temperature gradients were more heavily influenced by ambient conditions. These findings indicate that despite the insulative properties of fur, for mantled howling monkeys surface temperatures of furred areas still demonstrate a

  16. Uses of infrared thermography in the low-cost solar array program

    NASA Technical Reports Server (NTRS)

    Glazer, S. D.

    1982-01-01

    The Jet Propulsion Laboratory has used infrared thermography extensively in the Low-Cost Solar Array (LSA) photovoltaics program. A two-dimensional scanning infrared radiometer has been used to make field inspections of large free-standing photovoltaic arrays and smaller demonstration sites consisting of integrally mounted rooftop systems. These field inspections have proven especially valuable in the research and early development phases of the program, since certain types of module design flaws and environmental degradation manifest themselves in unique thermal patterns. The infrared camera was also used extensively in a series of laboratory tests on photovoltaic cells to obtain peak cell temperatures and thermal patterns during off-design operating conditions. The infrared field inspections and the laboratory experiments are discussed, and sample results are presented.

  17. Advances in applications and methodology for aerial infrared thermography

    NASA Astrophysics Data System (ADS)

    Stockton, Gregory R.

    2004-04-01

    Most aerial infrared (IR) is performed by the military, but there are commercial uses. Some of these non-military applications are the focus of this paper. Generally speaking, the farther away one can get from the object of an infrared survey, while maintaining the needed spatial resolution and thermal sensitivity, the more usable the data is. Wide areas and large objects can be effectively imaged from the air. In fact, the use of high-resolution aerial infrared imagery is often the only way that one can see slight nuances of temperature differences and trace the patterns of heat. In order to produce an easy to understand, high quality and useable report, the data must be acquired, recorded and processed in an efficient and effective way. This paper discusses the ongoing advances in methodology, platform and equipment required to produce high quality usable data for the end-user.

  18. Remote Infrared Thermography for In-Flight Flow Diagnostics

    NASA Technical Reports Server (NTRS)

    Shiu, H. J.; vanDam, C. P.

    1999-01-01

    The feasibility of remote in-flight boundary layer visualization via infrared in incompressible flow was established in earlier flight experiments. The past year's efforts focused on refining and determining the extent and accuracy of this technique of remote in-flight flow visualization via infrared. Investigations were made into flow separation visualization, visualization at transonic conditions, shock visualization, post-processing to mitigate banding noise in the NITE Hawk's thermograms, and a numeric model to predict surface temperature distributions. Although further flight tests are recommended, this technique continues to be promising.

  19. Monitoring of microvascular free flaps following oropharyngeal reconstruction using infrared thermography: first clinical experiences.

    PubMed

    Just, Maren; Chalopin, Claire; Unger, Michael; Halama, Dirk; Neumuth, Thomas; Dietz, Andreas; Fischer, Miloš

    2016-09-01

    The aim of this study is to investigate static and dynamic infrared (IR) thermography for intra- and postoperative free-flap monitoring following oropharyngeal reconstruction. Sixteen patients with oropharyngeal reconstruction by free radial forearm flap were included in this prospective, clinical study (05/2013-08/2014). Prior ("intraop_pre") and following ("intraop_post") completion of the microvascular anastomoses, IR thermography was performed for intraoperative flap monitoring. Further IR images were acquired one day ("postop_1") and 10 days ("postop_10") after surgery for postoperative flap monitoring. Of the 16, 15 transferred free radial forearm flaps did not show any perfusion failure. A significant decreasing mean temperature difference (∆T: temperature difference between the flap surface and the surrounding tissue in Kelvin) was measured at all investigation points in comparison with the temperature difference at "intraop_pre" (mean values on all patients: ∆T intraop_pre = -2.64 K; ∆T intraop_post = -1.22 K, p < 0.0015; ∆T postop_1 = -0.54 K, p < 0.0001; ∆T postop_10 = -0.58 K, p < 0.0001). Intraoperative dynamic IR thermography showed typical pattern of non-pathological rewarming due to re-established flap perfusion after completion of the microvascular anastomoses. Static and dynamic IR thermography is a promising, objective method for intraoperative and postoperative monitoring of free-flap reconstructions in head and neck surgery and to detect perfusion failure, before macroscopic changes in the tissue surface are obvious. A lack of significant decrease of the temperature difference compared to surrounding tissue following completion of microvascular anastomoses and an atypical rewarming following a thermal challenge are suggestive of flap perfusion failure.

  20. A protocol for analysing thermal stress in insects using infrared thermography.

    PubMed

    Gallego, Belén; Verdú, José R; Carrascal, Luis M; Lobo, Jorge M

    2016-02-01

    The study of insect responses to thermal stress has involved a variety of protocols and methodologies that hamper the ability to compare results between studies. For that reason, the development of a protocol to standardize thermal assays is necessary. In this sense, infrared thermography solves some of the problems allowing us to take continuous temperature measurements without handling the individuals, an important fact in cold-blooded organisms like insects. Here, we present a working protocol based on infrared thermography to estimate both cold and heat thermal stress in insects. We analyse both the change in the body temperature of individuals and their behavioural response. In addition, we used partial least squares regression for the statistical analysis of our data, a technique that solves the problem of having a large number of variables and few individuals, allowing us to work with rare or endemic species. To test our protocol, we chose two species of congeneric, narrowly distributed dung beetles that are endemic to the southeastern part of the Iberian Peninsula. With our protocol we have obtained five variables in the response to cold and twelve in the response to heat. With this methodology we discriminate between the two flightless species of Jekelius through their thermal response. In response to cold, Jekelius hernandezi showed a higher rate of cooling and reached higher temperatures of stupor and haemolymph freezing than Jekelius punctatolineatus. Both species displayed similar thermoregulation ranges before reaching lethal body temperature with heat stress. Overall, we have demonstrated that infrared thermography is a suitable method to assess insect thermal responses with a high degree of sensitivity, allowing for the discrimination between closely related species.

  1. Regional Skin Temperature Response to Moderate Aerobic Exercise Measured by Infrared Thermography

    PubMed Central

    Fernandes, Alex de Andrade; Amorim, Paulo Roberto dos Santos; Brito, Ciro José; Sillero-Quintana, Manuel; Bouzas Marins, João Carlos

    2016-01-01

    Background: Infrared thermography (IRT) does not require contact with the skin, and it is a convenient, reliable and non-invasive technique that can be used for monitoring the skin temperature (TSK). Objectives: The aim of this study was to monitor the variations in the regional TSK during exercise on 28 regions of interest (ROIs) (forehead, face, chest, abdomen, back, lumbar, anterior and posterior neck, and posterior and anterior views of the right and left hands, forearms, upper arms, thighs, and legs) with IRT. Patients and Methods: 12 physically active young males were monitored with IRT during the following three phases: a) 30 minutes before exercise b) while performing one hour of moderate intensity exercise on a treadmill at 60% of the VO2max, and c) 60 minutes after exercise. Results: During pre-exercise, all TSK reached a steady-state (P ≤ 0.05), which ensured adequate thermal stabilisation. At the beginning of exercise, there was a significant reduction in the TSK in most ROIs after 10 minutes of activity, except for the lower limbs (legs and thighs). After one hour of recovery, in the anterior view of the hands and thighs and in the posterior view of the legs, there were significant increases in the TSK compared to pre-exercise. Conclusions: There were significant distinctions in the skin temperature distribution during exercise according to the activity of the area under consideration during exercise, which may be important in the development of physiological models and heat flux analyses for different purposes. PMID:27217931

  2. Time-resolved pulsed stimulated infrared thermography applied to carbon-epoxy non destructive evaluation

    NASA Astrophysics Data System (ADS)

    Krapez, J.-C.; Boscher, D.; Delpech, Ph.; Deom, A.; Gardette, G.; Balageas, D.

    Since several years, time-resolved pulsed stimulated infrared thermography (SIRT) has been developed at ONERA with the aim of combining fast screening and quantitative characterization. The analysis of pixel by pixel thermograms leads to depth-location and thermal resistance images of delaminations. In this paper we present recent enhancements of the portable SIRT system and refinement of the data reduction procedure which demonstrate the possibility of detecting and evaluating delaminations in C-epoxy at depths higher than 3 mm. A 2-D inversion procedure is proposed to better characterize defects of reduced lateral extend as compared to the former 1-D method.

  3. A synchronized particle image velocimetry and infrared thermography technique applied to an acoustic streaming flow

    PubMed Central

    Sou, In Mei; Layman, Christopher N.; Ray, Chittaranjan

    2013-01-01

    Subsurface coherent structures and surface temperatures are investigated using simultaneous measurements of particle image velocimetry (PIV) and infrared (IR) thermography. Results for coherent structures from acoustic streaming and associated heating transfer in a rectangular tank with an acoustic horn mounted horizontally at the sidewall are presented. An observed vortex pair develops and propagates in the direction along the centerline of the horn. From the PIV velocity field data, distinct kinematic regions are found with the Lagrangian coherent structure (LCS) method. The implications of this analysis with respect to heat transfer and related sonochemical applications are discussed. PMID:24347810

  4. Mapping Soil Surface Macropores Using Infrared Thermography: An Exploratory Laboratory Study

    PubMed Central

    de Lima, João L. M. P.; Abrantes, João R. C. B.; Silva, Valdemir P.; de Lima, M. Isabel P.; Montenegro, Abelardo A. A.

    2014-01-01

    Macropores and water flow in soils and substrates are complex and are related to topics like preferential flow, nonequilibrium flow, and dual-continuum. Hence, the quantification of the number of macropores and the determination of their geometry are expected to provide a better understanding on the effects of pores on the soil's physical and hydraulic properties. This exploratory study aimed at evaluating the potential of using infrared thermography for mapping macroporosity at the soil surface and estimating the number and size of such macropores. The presented technique was applied to a small scale study (laboratory soil flume). PMID:25371915

  5. An Overview of Recent Application of Medical Infrared Thermography in Sports Medicine in Austria

    PubMed Central

    Hildebrandt, Carolin; Raschner, Christian; Ammer, Kurt

    2010-01-01

    Medical infrared thermography (MIT) is used for analyzing physiological functions related to skin temperature. Technological advances have made MIT a reliable medical measurement tool. This paper provides an overview of MIT’s technical requirements and usefulness in sports medicine, with a special focus on overuse and traumatic knee injuries. Case studies are used to illustrate the clinical applicability and limitations of MIT. It is concluded that MIT is a non-invasive, non-radiating, low cost detection tool which should be applied for pre-scanning athletes in sports medicine. PMID:22399901

  6. Outdoor thermal monitoring of large scale structures by infrared thermography integrated in an ICT based architecture

    NASA Astrophysics Data System (ADS)

    Dumoulin, Jean; Crinière, Antoine; Averty, Rodolphe

    2015-04-01

    An infrared system has been developed to monitor transport infrastructures in a standalone configuration. Results obtained on bridges open to traffic allows to retrieve the inner structure of the decks. To complete this study, experiments were carried out over several months to monitor two reinforced concrete beams of 16 m long and 21 T each. Detection of a damaged area over one of the two beams was made by Pulse Phase Thermography approach. Measurements carried out over several months. Finally, conclusion on the robustness of the system is proposed and perspectives are presented.

  7. Correlation Study Of Diffenrential Skin Temperatures (DST) For Ovulation Detection Using Infra-Red Thermography

    NASA Astrophysics Data System (ADS)

    Rao, K. H. S.; Shah, A. v.; Ruedi, B.

    1982-11-01

    The importance of ovulation time detection in the Practice of Natural Birth Control (NBC) as a contraceptive tool, and for natural/artificial insemination among women having the problem of in-fertility, is well known. The simple Basal Body Temperature (BBT) method of ovulation detection is so far unreliable. A newly proposed Differential Skin Temperature (DST) method may help minimize disturbing physiological effects and improve reliability. This paper explains preliminary results of a detailed correlative study on the DST method, using Infra-Red Thermography (IRT) imaging, and computer analysis techniques. Results obtained with five healthy, normally menstruating women volunteers will be given.

  8. Stimulated infrared thermography applied to thermophysical characterization of cultural heritage mural paintings

    NASA Astrophysics Data System (ADS)

    Bodnar, Jean-Luc; Nicolas, Jean-Louis; Mouhoubi, Kamel; Detalle, Vincent

    2012-11-01

    The purpose of this paper is to approach stimulated infrared thermography possibilities in terms of measuring longitudinal thermal diffusivity of mural paintings in situ. The measuring method principle is first submitted. It is based on temporal analysis of changes in the characteristic radius beams of spatial profiles of the photothermal signal, measured on the spot of the laser excitation. The feasibility of the method is demonstrated, thanks to a series of simulations. Lastly, the method enables to correctly estimate longitudinal thermal diffusivity in a test sample, and further in a fragment copy of "Saint Christophe" belonging to the Campana collection in the Louvre.

  9. Application of close-range aerial infrared thermography to detect landfill gas emissions: a case study

    NASA Astrophysics Data System (ADS)

    Tanda, G.; Migliazzi, M.; Chiarabini, V.; Cinquetti, P.

    2017-01-01

    Monitoring waste disposal sites is important to check that the produced biogas, potentially explosive, is properly collected by the biogas extraction system of the landfill site and to evaluate the residual biogas flow escaping from upper surface of the landfill. As the biogas migrates to the surface, the soil through which it flows is expected to reach a higher temperature than the surrounding environment; thus, measuring the thermal footprint of the landfill soil surface could allow the detection of biogas leakages and spots suitable for the gas extraction. Close-range aerial infrared thermography is an innovative approach able to identify thermal anomalies with a good resolution over a large region of the landfill surface. A simple procedure to deduce the biogas flow rate emerging from the soil into the atmosphere, based on infrared thermography measurements, is presented. The approach has been applied to a case study concerning a large landfill located in Genoa (Italy). Aerial infrared photographs taken during different days and seasons showed the presence of thermal anomalies over regions along the peripheral boundary of the landfill still not interested in biogas extraction.

  10. Measuring the temperature of high-luminous exitance surfaces with infrared thermography in LED applications

    NASA Astrophysics Data System (ADS)

    Perera, Indika U.; Narendran, Nadarajah

    2016-09-01

    Recently, light-emitting diode (LED) lighting systems have become popular due to their increased system performance. LED lighting system performance is affected by heat; therefore, it is important to know the temperature of a target surface or bulk medium in the LED system. In-situ temperature measurements of a surface or bulk medium using intrusive methods cause measurement errors. Typically, thermocouples are used in these applications to measure the temperatures of the various components in an LED system. This practice leads to significant errors, specifically when measuring surfaces with high-luminous exitance. In the experimental study presented in this paper, an infrared camera was used as an alternative to temperature probes in measuring LED surfaces with high-luminous exitance. Infrared thermography is a promising method because it does not respond to the visible radiation spectrum in the range of 0.38 to 0.78 micrometers. Usually, infrared thermography equipment is designed to operate either in the 3 to 5 micrometer or the 7 to 14 micrometer wavelength bands. To characterize the LED primary lens, the surface emissivity of the LED phosphor surface, the temperature dependence of the surface emissivity, the temperature of the target surface compared to the surrounding temperature, the field of view of the target, and the aim angle to the target surface need to be investigated, because these factors could contribute towards experimental errors. In this study, the effects of the above-stated parameters on the accuracy of the measured surface temperature were analyzed and reported.

  11. Clinical applications of dynamic infrared thermography in plastic surgery: a systematic review

    PubMed Central

    John, Hannah Eliza; Niumsawatt, Vachara; Whitaker, Iain S.

    2016-01-01

    Background Infrared thermography (IRT) has become an increasingly utilized adjunct to more expensive and/or invasive investigations in a range of surgical fields, no more so than in plastic surgery. The combination of functional assessment, flow characteristics and anatomical localization has led to increasing applications of this technology. This article aims to perform a systematic review of the clinical applications of IRT in plastic surgery. Methods A systematic literature search using the keywords ‘IRT’ and ‘dynamic infrared thermography (DIRT)’ has been accomplished. A total of 147 papers were extracted from various medical databases, of which 34 articles were subjected to a full read by two independent reviewers, to ensure the papers satisfied the inclusion and exclusion criteria. Studies focusing on the use of IRT in breast cancer diagnosis were excluded. Results A systematic review of 29 publications demonstrated the clinical applications of IRT in plastic surgery today. They include preoperative planning of perforators for free flaps, post operative monitoring of free flaps, use of IRT as an adjunct in burns depth analysis, in assessment of response to treatment in hemangioma and as a diagnostic test for cutaneous melanoma and carpal tunnel syndrome (CTS). Conclusions Modern infrared imaging technology with improved standardization protocols is now a credible, useful non-invasive tool in clinical practice. PMID:27047781

  12. Thermal diffusivity measurement of insulating material using infrared thermography

    NASA Astrophysics Data System (ADS)

    Chudzik, S.

    2011-09-01

    The article presents the results of research developing methods for determining the coefficient of thermal diffusivity of thermal insulating material. This method applies a periodic heating as an excitation and an infrared camera is used to measure the temperature distribution on the surface of tested material. In simulation study, the usefulness of known analytical solution of the inverse problem was examined using a three-dimensional model of the phenomenon of heat diffusion in the sample of tested material. To solve the coefficient inverse problem, an approach using artificial neural network is proposed. The measurements were performed on an experimental setup equipped with a ThermaCAM PM 595 infrared camera and frame grabber. The experiment allowed to verify the chosen 3D model of heat diffusion phenomenon and to determine suitability of the proposed test method.

  13. Thermal diffusivity measurement of insulating material using infrared thermography

    NASA Astrophysics Data System (ADS)

    Chudzik, S.

    2012-03-01

    The article presents the results of research developing methods for determining the coefficient of thermal diffusivity of thermal insulating material. This method applies a periodic heating as an excitation and an infrared camera is used to measure the temperature distribution on the surface of tested material. In simulation study, the usefulness of known analytical solution of the inverse problem was examined using a three-dimensional model of the phenomenon of heat diffusion in the sample of tested material. To solve the coefficient inverse problem, an approach using artificial neural network is proposed. The measurements were performed on an experimental setup equipped with a ThermaCAM PM 595 infrared camera and frame grabber. The experiment allowed to verify the chosen 3D model of heat diffusion phenomenon and to determine suitability of the proposed test method.

  14. The detection and thermal characterization of the inner structure of the ‘Musmeci’ bridge deck by infrared thermography monitoring

    NASA Astrophysics Data System (ADS)

    Dumoulin, Jean; Crinière, Antoine; Averty, Rodolphe

    2013-12-01

    In this study, the thermal monitoring of a bridge deck is carried out over several days thanks to an adapted infrared measurement system. This system does not just operate a single uncooled infrared camera but also other sensors (i.e., a weather station and a global positioning system (GPS). The detection of the inner structure of the deck is achieved by pulse phase thermography and principal component thermography approaches. A first characterization of the inner structure of the deck is proposed thanks to an original thermal modelling approach. The results obtained are discussed and analysed.

  15. Statistical Analysis of an Infrared Thermography Inspection of Reinforced Carbon-Carbon

    NASA Technical Reports Server (NTRS)

    Comeaux, Kayla

    2011-01-01

    Each piece of flight hardware being used on the shuttle must be analyzed and pass NASA requirements before the shuttle is ready for launch. One tool used to detect cracks that lie within flight hardware is Infrared Flash Thermography. This is a non-destructive testing technique which uses an intense flash of light to heat up the surface of a material after which an Infrared camera is used to record the cooling of the material. Since cracks within the material obstruct the natural heat flow through the material, they are visible when viewing the data from the Infrared camera. We used Ecotherm, a software program, to collect data pertaining to the delaminations and analyzed the data using Ecotherm and University of Dayton Log Logistic Probability of Detection (POD) Software. The goal was to reproduce the statistical analysis produced by the University of Dayton software, by using scatter plots, log transforms, and residuals to test the assumption of normality for the residuals.

  16. Integration of ground-penetrating radar, ultrasonic tests and infrared thermography for the analysis of a precious medieval rose window

    NASA Astrophysics Data System (ADS)

    Nuzzo, L.; Calia, A.; Liberatore, D.; Masini, N.; Rizzo, E.

    2010-04-01

    The integration of high-resolution, non-invasive geophysical techniques (such as ground-penetrating radar or GPR) with emerging sensing techniques (acoustics, thermography) can complement limited destructive tests to provide a suitable methodology for a multi-scale assessment of the state of preservation, material and construction components of monuments. This paper presents the results of the application of GPR, infrared thermography (IRT) and ultrasonic tests to the 13th century rose window of Troia Cathedral (Apulia, Italy), affected by widespread decay and instability problems caused by the 1731 earthquake and reactivated by recent seismic activity. This integrated approach provided a wide amount of complementary information at different scales, ranging from the sub-centimetre size of the metallic joints between the various architectural elements, narrow fractures and thin mortar fillings, up to the sub-metre scale of the internal masonry structure of the circular ashlar curb linking the rose window to the façade, which was essential to understand the original building technique and to design an effective restoration strategy.

  17. The Role of Infrared Thermography as a Non-Invasive Tool for the Detection of Lameness in Cattle

    PubMed Central

    Alsaaod, Maher; Schaefer, Allan L.; Büscher, Wolfgang; Steiner, Adrian

    2015-01-01

    The use of infrared thermography for the identification of lameness in cattle has increased in recent years largely because of its non-invasive properties, ease of automation and continued cost reductions. Thermography can be used to identify and determine thermal abnormalities in animals by characterizing an increase or decrease in the surface temperature of their skin. The variation in superficial thermal patterns resulting from changes in blood flow in particular can be used to detect inflammation or injury associated with conditions such as foot lesions. Thermography has been used not only as a diagnostic tool, but also to evaluate routine farm management. Since 2000, 14 peer reviewed papers which discuss the assessment of thermography to identify and manage lameness in cattle have been published. There was a large difference in thermography performance in these reported studies. However, thermography was demonstrated to have utility for the detection of contralateral temperature difference and maximum foot temperature on areas of interest. Also apparent in these publications was that a controlled environment is an important issue that should be considered before image scanning. PMID:26094632

  18. The Role of Infrared Thermography as a Non-Invasive Tool for the Detection of Lameness in Cattle.

    PubMed

    Alsaaod, Maher; Schaefer, Allan L; Büscher, Wolfgang; Steiner, Adrian

    2015-06-18

    The use of infrared thermography for the identification of lameness in cattle has increased in recent years largely because of its non-invasive properties, ease of automation and continued cost reductions. Thermography can be used to identify and determine thermal abnormalities in animals by characterizing an increase or decrease in the surface temperature of their skin. The variation in superficial thermal patterns resulting from changes in blood flow in particular can be used to detect inflammation or injury associated with conditions such as foot lesions. Thermography has been used not only as a diagnostic tool, but also to evaluate routine farm management. Since 2000, 14 peer reviewed papers which discuss the assessment of thermography to identify and manage lameness in cattle have been published. There was a large difference in thermography performance in these reported studies. However, thermography was demonstrated to have utility for the detection of contralateral temperature difference and maximum foot temperature on areas of interest. Also apparent in these publications was that a controlled environment is an important issue that should be considered before image scanning.

  19. [Objective assessment of facial paralysis using local binary pattern in infrared thermography].

    PubMed

    Liu, Xulong; Hong, Wenxue; Zhang, Tao; Wu, Zhenying

    2013-02-01

    Facial paralysis is a frequently-occurring disease, which causes the loss of the voluntary muscles on one side of the face due to the damages the facial nerve and results in an inability to close the eye and leads to dropping of the angle of the mouth. There have been few objective methods to quantitatively diagnose it and assess this disease for clinically treating the patients so far. The skin temperature distribution of a healthy human body exhibits a contralateral symmetry. Facial paralysis usually causes an alteration of the temperature distribution of body with the disease. This paper presents the use of the histogram distance of bilateral local binary pattern (LBP) in the facial infrared thermography to measure the asymmetry degree of facial temperature distribution for objective assessing the severity of facial paralysis. Using this new method, we performed a controlled trial to assess the facial nerve function of the healthy subjects and the patients with Bell's palsy respectively. The results showed that the mean sensitivity and specificity of this method are 0.86 and 0.89 respectively. The correlation coefficient between the asymmetry degree of facial temperature distribution and the severity of facial paralysis is an average of 0.657. Therefore, the histogram distance of local binary pattern in the facial infrared thermography is an efficient clinical indicator with respect to the diagnosis and assessment of facial paralysis.

  20. Integration of infrared thermography and high-frequency electromagnetic methods in archaeological surveys

    NASA Astrophysics Data System (ADS)

    Carlomagno, Giovanni Maria; Di Maio, Rosa; Fedi, Maurizio; Meola, Carosena

    2011-09-01

    This work is focused on the integration of infrared thermography and ground penetrating radar for the inspection of architectonic structures. First, laboratory tests were carried out with both techniques by considering an ad hoc specimen made of concrete and with the insertion of anomalies of a different nature and at different depths. Such tests provided helpful information for ongoing inspections in situ, which were later performed in two important Italian archaeological sites, namely Pompeii (Naples) and Nora (Cagliari). In the first site, the exploration was devoted to the analysis of the wall paintings of Villa Imperiale with the aim of evaluating the state of conservation of frescoes as well of the underneath masonry structure. As main findings, the applied techniques allowed outlining some areas, which were damaged by ingression in-depth of moisture and/or by disaggregation of the constituent materials, and also for recognition of previous restoration. In the archaeological area of Nora, instead, the attention was driven towards the evaluation of the state of degradation of the theatre remnants. Our prospections show that the front side of the theatre, being more strongly affected by degradation, needs a massive restoration work. As a general result, we demonstrated that a joint interpretation of infrared thermography and ground penetrating radar data supplies detailed 3D information from near-surface to deep layers, which may assist in restoration planning.

  1. Reconstruction of a nonlinear heat transfer law from uncomplete boundary data by means of infrared thermography

    NASA Astrophysics Data System (ADS)

    Clarelli, Fabrizio; Inglese, Gabriele

    2016-11-01

    Heat exchange between a conducting plate and the environment is described here by means of an unknown nonlinear function F of the temperature u. In this paper we construct a method for recovering F by means of polynomial expansion, perturbation theory and the toolbox of thermal inverse problems. We test our method on two examples: In the first one, we heat the plate (initially at 20 ^\\circ {{C}}) from one side, read the temperature on the same side and identify the heat exchange law on the opposite side (active thermography); in the second example we measure the temperature of one side of the plate (initially at 1500 ^\\circ {{C}}) and study the heat exchange while cooling (passive thermography).

  2. Mechanical and Infrared Thermography Analysis of Shape Memory Polyurethane

    NASA Astrophysics Data System (ADS)

    Pieczyska, Elzbieta Alicja; Maj, Michal; Kowalczyk-Gajewska, Katarzyna; Staszczak, Maria; Urbanski, Leszek; Tobushi, Hisaaki; Hayashi, Shunichi; Cristea, Mariana

    2014-07-01

    Multifunctional new material—polyurethane shape memory polymer (PU-SMP)—was subjected to tension carried out at room temperature at various strain rates. The influence of effects of thermomechanical couplings on the SMP mechanical properties was studied, based on the sample temperature changes, measured by a fast and sensitive infrared camera. It was found that the polymer deformation process strongly depends on the strain rate applied. The initial reversible strain is accompanied by a small drop in temperature, called thermoelastic effect. Its maximal value is related to the SMP yield point and increases upon increase of the strain rate. At higher strains, the stress and temperature significantly increase, caused by reorientation of the polymer molecular chains, followed by the stress drop and its subsequent increase accompanying the sample rupture. The higher strain rate, the higher stress, and temperature changes were obtained, since the deformation process was more dynamic and has occurred in almost adiabatic conditions. The constitutive model of SMP valid in finite strain regime was developed. In the proposed approach, SMP is described as a two-phase material composed of hyperelastic rubbery phase and elastic-viscoplastic glassy phase, while the volume content of phases is specified by the current temperature.

  3. Framework for 2D-3D image fusion of infrared thermography with preoperative MRI.

    PubMed

    Hoffmann, Nico; Weidner, Florian; Urban, Peter; Meyer, Tobias; Schnabel, Christian; Radev, Yordan; Schackert, Gabriele; Petersohn, Uwe; Koch, Edmund; Gumhold, Stefan; Steiner, Gerald; Kirsch, Matthias

    2017-01-23

    Multimodal medical image fusion combines information of one or more images in order to improve the diagnostic value. While previous applications mainly focus on merging images from computed tomography, magnetic resonance imaging (MRI), ultrasonic and single-photon emission computed tomography, we propose a novel approach for the registration and fusion of preoperative 3D MRI with intraoperative 2D infrared thermography. Image-guided neurosurgeries are based on neuronavigation systems, which further allow us track the position and orientation of arbitrary cameras. Hereby, we are able to relate the 2D coordinate system of the infrared camera with the 3D MRI coordinate system. The registered image data are now combined by calibration-based image fusion in order to map our intraoperative 2D thermographic images onto the respective brain surface recovered from preoperative MRI. In extensive accuracy measurements, we found that the proposed framework achieves a mean accuracy of 2.46 mm.

  4. Stimulated infrared thermography applied to differentiate scar tissue from peri-scar tissue: a preliminary study.

    PubMed

    Riquet, Damien; Houel, Nicolas; Bodnar, Jean-Luc

    2016-08-01

    Every human injury leads to a scar formation. The healing process leads to the formation of new tissue: the scar, which is different from the original tissue. This process is influenced by mechanical strength and the local vasculature is modified. The purpose of this study is to show that there are various temperatures between the scar and the peri-scar area associated with the healing process that can be estimated using the thermal infrared camera. In the study, 12 scars were stimulated by cold. Several changes of temperature were observed between scar and peri-scar area for 10 min. Scars appeared significantly colder with a Wilcoxon test (p = 0.01). Results showed that stimulated infrared thermography can be used to monitor the temperature difference between the scar and peri-scar tissue.

  5. Contribution to the improvement of heritage mural painting non-destructive testing by stimulated infrared thermography

    NASA Astrophysics Data System (ADS)

    Bodnar, Jean-Luc; Mouhoubi, Kamel; Di Pallo, Luigi; Detalle, Vincent; Vallet, Jean-Marc; Duvaut, Thierry

    2013-10-01

    Non-destructive testing of heritage mural paintings by means of stimulated infrared thermography has now become rather efficient [1-14]. However, pigments, which form a pictorial layer, have contrasting radiative properties possibly leading to artifact detection. In this paper, attempts to alleviate this difficulty are presented. Based on the spectroscopic study of different paint layers, one can argue that, in the medium infrared field, this radiative disparity decreases significantly. Then, with similar settings, it can be shown that ceramic radiative sources allow reaching this wavelength band. Finally, on the basis of a study carried out on an academic sample and a partial copy of a fresco from the cathedral of Angers, combining ceramic heat sources with a laboratory SAMMTHIR experimental setup enables to make real headway in terms of defects' detection.

  6. Body Functions and Structures Pertinent to Infrared Thermography-Based Access for Clients with Severe Motor Disabilities

    ERIC Educational Resources Information Center

    Memarian, Negar; Venetsanopoulos, Anastasios N.; Chau, Tom

    2011-01-01

    Infrared thermography has been recently proposed as an access technology for individuals with disabilities, but body functions and structures pertinent to its use have not been documented. Seven clients (2 adults, 5 youth) with severe disabilities and their primary caregivers participated in this study. All clients had a Gross Motor Functional…

  7. Scrotal infrared digital thermography as a predictor of seasonal effects on sperm traits in Braford bulls.

    PubMed

    Menegassi, Silvio Renato Oliveira; Barcellos, Júlio Otavio Jardim; Dias, Eduardo Antunes; Koetz, Celso; Pereira, Gabriel Ribas; Peripolli, Vanessa; McManus, Concepta; Canozzi, Maria Eugênia Andrighetto; Lopes, Flávio Guiselli

    2015-03-01

    The aim of this study was to assess the seasonal effects of the environment on semen quality in bulls, using infrared thermography. Sperm motility (M), mass motion (MM), and vigor (VIG) were evaluated in sperm samples from 17 Bradford bulls aged approximately 24 months at the beginning of the study. Infrared thermography images and data were collected using an infrared FLIR T 300 camera and Quick Report 1.2 SP2 software to determine the temperature of the proximal and distal poles of the testis and to assess the testicular temperature gradient. The seasonal effects on physiological, seminal, and climatic variables were analyzed by the GLM ANOVA and CORR procedures using SAS®. The microclimatic factors were recorded in hourly intervals, and the daily mean temperature and mean relative humidity were calculated to determine the daily temperature-humidity index (THI) every day for 1 year. The temperature gradient (TG) variations of the testes were significantly higher in the autumn (4.5 °C), winter (4.0 °C), and spring (2.9 °C) compared to summer (0.9 °C) (P < 0.05). Ocular globe temperatures were lower in the winter (27.6 °C) and autumn (26.8 °C) compared to summer (33.9 °C) and spring (31.1 °C) (P < 0.05). The average MM (2.58), M (52.64), and VIG (2.70) of the semen decreased in the summer compared to other seasons (P < 0.01). The TG was negatively correlated with THI (-0.44; P < 0.05). For the seminal variables, MaD (-0.45; P < 0.05) and TD (-0.50; P < 0.01) presented a negative correlation with TG. The TG had a positive correlation between M and VIG, which had values of 0.36 and 0.35, respectively (P < 0.05). We have concluded that infrared thermography can be used to assess the testicular temperature gradient and its consequences on physical and quantitative aspects of sperm.

  8. Scrotal infrared digital thermography as a predictor of seasonal effects on sperm traits in Braford bulls

    NASA Astrophysics Data System (ADS)

    Menegassi, Silvio Renato Oliveira; Barcellos, Júlio Otavio Jardim; Dias, Eduardo Antunes; Koetz, Celso; Pereira, Gabriel Ribas; Peripolli, Vanessa; McManus, Concepta; Canozzi, Maria Eugênia Andrighetto; Lopes, Flávio Guiselli

    2015-03-01

    The aim of this study was to assess the seasonal effects of the environment on semen quality in bulls, using infrared thermography. Sperm motility (M), mass motion (MM), and vigor (VIG) were evaluated in sperm samples from 17 Bradford bulls aged approximately 24 months at the beginning of the study. Infrared thermography images and data were collected using an infrared FLIR T 300 camera and Quick Report 1.2 SP2 software to determine the temperature of the proximal and distal poles of the testis and to assess the testicular temperature gradient. The seasonal effects on physiological, seminal, and climatic variables were analyzed by the GLM ANOVA and CORR procedures using SAS®. The microclimatic factors were recorded in hourly intervals, and the daily mean temperature and mean relative humidity were calculated to determine the daily temperature-humidity index (THI) every day for 1 year. The temperature gradient (TG) variations of the testes were significantly higher in the autumn (4.5 °C), winter (4.0 °C), and spring (2.9 °C) compared to summer (0.9 °C) ( P < 0.05). Ocular globe temperatures were lower in the winter (27.6 °C) and autumn (26.8 °C) compared to summer (33.9 °C) and spring (31.1 °C) ( P < 0.05). The average MM (2.58), M (52.64), and VIG (2.70) of the semen decreased in the summer compared to other seasons ( P < 0.01). The TG was negatively correlated with THI (-0.44; P < 0.05). For the seminal variables, MaD (-0.45; P < 0.05) and TD (-0.50; P < 0.01) presented a negative correlation with TG. The TG had a positive correlation between M and VIG, which had values of 0.36 and 0.35, respectively ( P < 0.05). We have concluded that infrared thermography can be used to assess the testicular temperature gradient and its consequences on physical and quantitative aspects of sperm.

  9. Active thermography and post-processing image enhancement for recovering of abraded and paint-covered alphanumeric identification marks

    NASA Astrophysics Data System (ADS)

    Montanini, R.; Quattrocchi, A.; Piccolo, S. A.

    2016-09-01

    Alphanumeric marking is a common technique employed in industrial applications for identification of products. However, the realised mark can undergo deterioration, either by extensive use or voluntary deletion (e.g. removal of identification numbers of weapons or vehicles). For recovery of the lost data many destructive or non-destructive techniques have been endeavoured so far, which however present several restrictions. In this paper, active infrared thermography has been exploited for the first time in order to assess its effectiveness in restoring paint covered and abraded labels made by means of different manufacturing processes (laser, dot peen, impact, cold press and scribe). Optical excitation of the target surface has been achieved using pulse (PT), lock-in (LT) and step heating (SHT) thermography. Raw infrared images were analysed with a dedicated image processing software originally developed in Matlab™, exploiting several methods, which include thermographic signal reconstruction (TSR), guided filtering (GF), block guided filtering (BGF) and logarithmic transformation (LN). Proper image processing of the raw infrared images resulted in superior contrast and enhanced readability. In particular, for deeply abraded marks, good outcomes have been obtained by application of logarithmic transformation to raw PT images and block guided filtering to raw phase LT images. With PT and LT it was relatively easy to recover labels covered by paint, with the latter one providing better thermal contrast for all the examined targets. Step heating thermography never led to adequate label identification instead.

  10. An active thermography approach for thermal and electrical characterization of thermoelectric materials

    NASA Astrophysics Data System (ADS)

    Streza, M.; Longuemart, S.; Guilmeau, E.; Strzalkowski, K.; Touati, K.; Depriester, M.; Maignan, A.; Sahraoui, A. Hadj

    2016-07-01

    The enhancement of figure of merit (ZT) of thermoelectrics is becoming extremely important for an efficient conversion of thermal energy into electrical energy. In this respect, reliable measurements of thermal and electrical parameters are of paramount importance in order to characterize thermoelectric materials in terms of their efficiency. In this work, a combined theoretical-experimental active thermography approach is presented. The method consists of selecting the right sequential interdependence between the excitation frequency and the sampling rate of the infrared camera, by computing a temporal Fourier analysis of each pixel of the recorded IR image. The method is validated by using a reference sample which is then applied to a recent synthesized titanium trisulphide thermoelectric material (TiS3). By combining AC and steady-state experiments, one can obtain information on both thermal and electrical parameters of TE materials (namely thermal diffusivity, Seebeck coefficient). The thermal diffusivity and thermal conductivity of TiS3 are also measured using photothermal radiometry technique (PTR) and the resulting values of these parameters are α  =  9.7*10-7 m2 s-1 and k  =  2.2 W m-1 K, respectively. The results obtained with the two techniques are in good agreement. In the case of TE materials, the main benefit of the proposed method is related to its non-contact nature and the possibility of obtaining the electric potential and temperature at the same probes. The Seebeck coefficient obtained by active IR thermography (S  =  -554 μV K-1) is consistent with the one obtained using an ULVAC-ZEM3 system (S  =  -570 μV K-1). For a large number of users of thermographic cameras, which are not equipped with a lock-in thermography module, the present approach provides an affordable and cheaper solution.

  11. Energetic costs of mange in wolves estimated from infrared thermography

    USGS Publications Warehouse

    Cross, Paul C.; Almberg, Emily S.; Haase, Catherine G; Hudson, Peter J.; Maloney, Shane K; Metz, Matthew C; Munn, Adam J; Nugent, Paul; Putzeys, Olivier; Stahler, Daniel R.; Stewart, Anya C; Smith, Doug W.

    2016-01-01

    Parasites, by definition, extract energy from their hosts and thus affect trophic and food web dynamics even when the parasite may have limited effects on host population size. We studied the energetic costs of mange (Sarcoptes scabiei) in wolves (Canis lupus) using thermal cameras to estimate heat losses associated with compromised insulation during the winter. We combined the field data of known, naturally infected wolves with data set on captive wolves with shaved patches of fur as a positive control to simulate mange-induced hair loss. We predict that during the winter in Montana, more severe mange infection increases heat loss by around 5.2 to 12 MJ per night (1240 to 2850 kcal, or a 65% to 78% increase) for small and large wolves, respectively accounting for wind effects. To maintain body temperature would require a significant proportion of a healthy wolf's total daily energy demands (18-22 MJ/day). We also predict how these thermal costs may increase in colder climates by comparing our predictions in Bozeman, Montana to those from a place with lower ambient temperatures (Fairbanks, Alaska). Contrary to our expectations, the 14°C differential between these regions was not as important as the potential differences in wind speed. These large increases in energetic demands can be mitigated by either increasing consumption rates or decreasing other energy demands. Data from GPS-collared wolves indicated that healthy wolves move, on average, 17 km per day, which was reduced by 1.5, 1.8 and 6.5 km for light, medium, and severe hair loss. In addition, the wolf with the most hair loss was less active at night and more active during the day, which is the converse of the movement patterns of healthy wolves. At the individual level mange infections create significant energy demands and altered behavioral patterns, this may have cascading effects on prey consumption rates, food web dynamics, predator-prey interactions, and scavenger communities.

  12. Biomechanical stress maps of an artificial femur obtained using a new infrared thermography technique validated by strain gages.

    PubMed

    Shah, Suraj; Bougherara, Habiba; Schemitsch, Emil H; Zdero, Rad

    2012-12-01

    Femurs are the heaviest, longest, and strongest long bones in the human body and are routinely subjected to cyclic forces. Strain gages are commonly employed to experimentally validate finite element models of the femur in order to generate 3D stresses, yet there is little information on a relatively new infrared (IR) thermography technique now available for biomechanics applications. In this study, IR thermography validated with strain gages was used to measure the principal stresses in the artificial femur model from Sawbones (Vashon, WA, USA) increasingly being used for biomechanical research. The femur was instrumented with rosette strain gages and mechanically tested using average axial cyclic forces of 1500 N, 1800 N, and 2100 N, representing 3 times body weight for a 50 kg, 60 kg, and 70 kg person. The femur was oriented at 7° of adduction to simulate the single-legged stance phase of walking. Stress maps were also obtained using an IR thermography camera. Results showed good agreement of IR thermography vs. strain gage data with a correlation of R(2)=0.99 and a slope=1.08 for the straight line of best fit. IR thermography detected the highest principal stresses on the superior-posterior side of the neck, which yielded compressive values of -91.2 MPa (at 1500 N), -96.0 MPa (at 1800 N), and -103.5 MPa (at 2100 N). There was excellent correlation between IR thermography principal stress vs. axial cyclic force at 6 locations on the femur on the lateral (R(2)=0.89-0.99), anterior (R(2)=0.87-0.99), and posterior (R(2)=0.81-0.99) sides. This study shows IR thermography's potential for future biomechanical applications.

  13. Technical note: Relationship between infrared thermography and heat production in young bulls.

    PubMed

    Gomes, R A; Busato, K C; Ladeira, M M; Johnson, K A; Galvão, M C; Rodrigues, A C; Lourençoni, D; Chizzotti, M L

    2016-03-01

    The traditional techniques to measure heat production (HP) are calorimetry (direct and indirect) and comparative slaughter. Both methods are expensive and require extensive amounts of time and infrastructure. Infrared thermography (IRT) could be a faster and less expensive alternative to estimate cattle HP. The objective of this project was to evaluate the use of the IRT technique as an indicator of HP in cattle. A total of 24 bulls (12 Nellore and 12 Black Angus) with initial BW of 380 ± 7 kg were used. Initially, 4 animals of each breed were harvested (baseline animals) and simple regressions were developed for each breed from these baseline animals to estimate the initial chemical composition of the remaining bulls. Eight animals of each breed were fed a silage/concentrate diet for ad libitum intake in individual stalls. On the 25th, 50th, and 75th experimental day, infrared thermal images (Fluke Ti 55ft; Fluke Corporation) were taken of each animal's face to access skin and ocular surface temperatures. A metabolism trial was conducted to estimate the ME intake (MEI). After 84 experimental days, the cattle were harvested and retained energy (RE) and HP were calculated. The data were analyzed using the MIXED and REG procedures of SAS adopting a significance level of 0.05. Angus cattle had a greater daily MEI, HP, and skin and eye temperatures than Nellore. We found significant correlations ( ≤ 0.005) between daily HP and maximum ( = 0.65) and average skin temperatures ( = 0.65) and maximum ( = 0.65) and average ocular surface ( = 0.69) temperatures recorded on d 50. Infrared thermography has potential to be used to evaluate HP in cattle.

  14. Thermal Integrity Assessment of Building Envelopes of Experimental Houses Using Infrared Thermography

    SciTech Connect

    Biswas, Kaushik; Kosny, Jan; Miller, William A

    2010-01-01

    Zero Energy Building Research Alliance, or ZEBRAlliance, is a joint DOE-ORNL-construction industry initiative to develop and demonstrate new energy efficiency technologies for residential buildings, as well as fine-tune and integrate existing technologies, to lower energy costs. Construction of residential envelopes, the diaphragms that separate the inside from outdoors, can have enormous impact on whole-building energy usage. Consequently, post-construction thermal integrity assessment of the building envelopes in the experimental ZEBRAlliance homes is an integral part of the research and development cycle. Nondestructive infrared (IR) thermography provides a relatively easy and quick means of inspecting the experimental homes for thermal bridging, insulation imperfections, moisture penetration, air leakage, etc. Two experimental homes located in Oak Ridge, TN were inspected using IR thermography. The homes are designed with two different envelope systems: (i) Structural Insulated Panels (SIP home) consisting of an insulating foam core sandwiched between oriented strand boards, and (ii) Optimal Value Framing (OVF home) using innovatively spaced wood studs, which are designed to minimize the amount of wood framing, reduce thermal bridging, and lower material costs. IR thermal imaging was performed from both outside and inside of the homes. In this paper, IR images of roof and wall sections of the homes are presented and discussed with respect to identification of areas of thermal bridging and any insulation deficiencies.

  15. Energetic costs of mange in wolves estimated from infrared thermography.

    PubMed

    Cross, P C; Almberg, E S; Haase, C G; Hudson, P J; Maloney, S K; Metz, M C; Munn, A J; Nugent, P; Putzeys, O; Stahler, D R; Stewart, A C; Smith, D W

    2016-08-01

    Parasites, by definition, extract energy from their hosts and thus affect trophic and food web dynamics even when the parasite may have limited effects on host population size. We studied the energetic costs of mange (Sarcoptes scabiei) in wolves (Canis lupus) using thermal cameras to estimate heat losses associated with compromised insulation during the winter. We combined the field data of known, naturally infected wolves with a data set on captive wolves with shaved patches of fur as a positive control to simulate mange-induced hair loss. We predict that during the winter in Montana, more severe mange infection increases heat loss by around 5.2-12 MJ per night (1,240-2,850 kcal, or a 65-78% increase) for small and large wolves, respectively, accounting for wind effects. To maintain body temperature would require a significant proportion of a healthy wolf's total daily energy demands (18-22 MJ/day). We also predict how these thermal costs may increase in colder climates by comparing our predictions in Bozeman, Montana to those from a place with lower ambient temperatures (Fairbanks, Alaska). Contrary to our expectations, the 14°C differential between these regions was not as important as the potential differences in wind speed. These large increases in energetic demands can be mitigated by either increasing consumption rates or decreasing other energy demands. Data from GPS-collared wolves indicated that healthy wolves move, on average, 17 km per day, which was reduced by 1.5, 1.8, and 6.5 km for light, medium, and severe hair loss. In addition, the wolf with the most hair loss was less active at night and more active during the day, which is the converse of the movement patterns of healthy wolves. At the individual level, mange infections create significant energy demands and altered behavioral patterns, this may have cascading effects on prey consumption rates, food web dynamics, predator-prey interactions, and scavenger communities.

  16. Association of digital cushion thickness with sole temperature measured with the use of infrared thermography.

    PubMed

    Oikonomou, G; Trojacanec, P; Ganda, E K; Bicalho, M L S; Bicalho, R C

    2014-07-01

    The main objective of this study was to investigate the association between digital cushion thickness and sole temperature measured by infrared thermography. Data were collected from 216 lactating Holstein cows at 4 to 10d in milk (DIM). Cows were locomotion scored and sole temperature was measured after claw trimming (a minimum delay of 3 min was allowed for the hoof to cool) using an infrared thermography camera. Temperature was measured at the typical ulcer site of the lateral digit of the left hind foot. Immediately after the thermographic image was obtained, the thickness of the digital cushion was measured by ultrasonography. Rumen fluid samples were collected with a stomach tube and sample pH was measured immediately after collection. Additionally, a blood sample was obtained and used for measurements of serum concentrations of β-hydroxybutyrate (BHBA), nonesterified fatty acids (NEFA), and haptoglobin. To evaluate the associations of digital cushion thickness with sole temperature, a linear regression model was built using the GLIMMIX procedure in SAS software (SAS Institute Inc., Cary, NC). Sole temperature was the response variable, and digital cushion thickness quartiles, locomotion score group, rumen fluid pH, rumen fluid sample volume, environmental temperature, age in days, and serum levels of NEFA, BHBA, and haptoglobin were fitted in the model. Only significant variables were retained in the final model. Simple linear regression scatter plots were used to illustrate associations between sole temperature (measured by infrared thermography at the typical ulcer site) and environmental temperature and between NEFA and BHBA serum levels and haptoglobin. One-way ANOVA was used to compare rumen fluid pH for different locomotion score groups and for different digital cushion quartiles. Results from the multivariable linear regression model showed that sole temperature increased as locomotion scores increased and decreased as digital cushion thickness

  17. Study on the heat flux reconstruction with the infrared thermography for the divertor target plates in the KSTAR tokamak

    NASA Astrophysics Data System (ADS)

    Kang, C. S.; Lee, H. H.; Oh, S.; Lee, S. G.; Wi, H. M.; Kim, Y. S.; Kim, H. S.

    2016-08-01

    An infrared (IR) thermography is the preferred diagnostic that can quantify heat flux by measuring the surface temperature distributions of the divertor plates. The IR thermography is successfully instrumented on Korea Superconducting Tokamak Advanced Research (KSTAR). In this study, finite volume method is considered to solve the heat conduction equations. 1D-, 2D-, and 3D models are developed and compared with various calculation algorithms, such as Duhamel's theorem and THEODOR. These comparisons show good agreement. In order to acquire more efficient and reliable calculation results, we consider two numerical analysis schemes, influence of temperature on thermal properties and image stabilization. Recently, this reconstruction code is successfully applied to the KSTAR IR thermography.

  18. Study on the heat flux reconstruction with the infrared thermography for the divertor target plates in the KSTAR tokamak.

    PubMed

    Kang, C S; Lee, H H; Oh, S; Lee, S G; Wi, H M; Kim, Y S; Kim, H S

    2016-08-01

    An infrared (IR) thermography is the preferred diagnostic that can quantify heat flux by measuring the surface temperature distributions of the divertor plates. The IR thermography is successfully instrumented on Korea Superconducting Tokamak Advanced Research (KSTAR). In this study, finite volume method is considered to solve the heat conduction equations. 1D-, 2D-, and 3D models are developed and compared with various calculation algorithms, such as Duhamel's theorem and THEODOR. These comparisons show good agreement. In order to acquire more efficient and reliable calculation results, we consider two numerical analysis schemes, influence of temperature on thermal properties and image stabilization. Recently, this reconstruction code is successfully applied to the KSTAR IR thermography.

  19. Active Thermography for the Detection of Defects in Powder Metallurgy Compacts

    SciTech Connect

    Benzerrouk, Souheil; Ludwig, Reinhold; Apelian, Diran

    2007-03-21

    Active thermography is an established NDE technique that has become the method of choice in many industrial applications which require non-contact access to the parts under test. Unfortunately, when conducting on-line infrared (IR) inspection of powder metallic compacts, complications can arise due the generally low emissivity of metals and the thermally noisy environment typically encountered in manufacturing plants. In this paper we present results of an investigation that explores the suitability of active IR imaging of powder metallurgy compacts for the detection of surface and sub-surface defects in the pre-sinter state and in an on-line manufacturing setting to ensure complete quality assurance. Additional off-line tests can be carried out for statistical quality analyses. In this research, the IR imaging of sub-surface defects is based on a transient instrumentation approach that relies on an electric control system which synchronizes and monitors the thermal response due to an electrically generated heat source. Preliminary testing reveals that this newly developed pulsed thermography system can be employed for the detection of subsurface defects in green-state parts. Practical measurements agree well with theoretical predictions. The inspection approach being developed can be used for the testing of green-state compacts as they exit the compaction press at speeds of up to 1,000 parts per hour.

  20. Low-Altitude and Land-Based Infrared Thermography to Identify Types of Groundwater Discharge in NWT Streams

    NASA Astrophysics Data System (ADS)

    Conant, B.; Mochnacz, N. J.

    2009-05-01

    In tributaries of the Mackenzie River in the Northwest Territories (NWT), Canada, groundwater discharge provides critical fish habitat for Dolly Varden and bull trout populations by maintaining base flows, creating thermal refugia in winter, and providing stable riverbed temperatures for spawning. Where temperature contrasts exist between surface water and groundwater, infrared thermography can use heat as a tracer to locate groundwater discharge areas. Thermal images acquired from satellites and high altitude airplanes tend to be expensive, lack the resolution necessary to identify small discharge locations, and do not allow real time decisions to investigate and ground truth identified temperature anomalies. Therefore, a system was developed using a handheld FLIR ThermaCam P25 infrared camera, visual video camera, infrared video capture system, and GPS in a low flying helicopter and on the ground. The advantage of the system was its ability to inexpensively and efficiently characterize several kilometer long reaches of river and identify springs and seeps on a sub-meter scale and in real time. The different types of groundwater discharge that can occur in these streams include: deep geothermally heated groundwater; shallow groundwater; and active zone water, but differentiating them can be difficult because observed thermal anomalies can be non-unique functions of the initial groundwater temperature, magnitude of discharge, air and surface water temperatures, and temporal variations. Work performed in March and September easily detected spring and seeps of deep groundwater (8 to 13 ° C) at Smith Creek, Gibson Creek, Gayna River, and Little Fish Creek. Shallow groundwater discharge was detected (1 to 3 ° C) at White Sand Creek, Canyon Creek, and Fish Creek, but was more difficult to identify. Subtle variations from surrounding temperatures (<1 ° C) at some sites suggested seeps from the hyporheic zone or possibly the active zone. The limitations of infrared

  1. Infrared thermography based on artificial intelligence as a screening method for carpal tunnel syndrome diagnosis.

    PubMed

    Jesensek Papez, B; Palfy, M; Mertik, M; Turk, Z

    2009-01-01

    This study further evaluated a computer-based infrared thermography (IRT) system, which employs artificial neural networks for the diagnosis of carpal tunnel syndrome (CTS) using a large database of 502 thermal images of the dorsal and palmar side of 132 healthy and 119 pathological hands. It confirmed the hypothesis that the dorsal side of the hand is of greater importance than the palmar side when diagnosing CTS thermographically. Using this method it was possible correctly to classify 72.2% of all hands (healthy and pathological) based on dorsal images and > 80% of hands when only severely affected and healthy hands were considered. Compared with the gold standard electromyographic diagnosis of CTS, IRT cannot be recommended as an adequate diagnostic tool when exact severity level diagnosis is required, however we conclude that IRT could be used as a screening tool for severe cases in populations with high ergonomic risk factors of CTS.

  2. A novel calibration method for an infrared thermography system applied to heat transfer experiments

    NASA Astrophysics Data System (ADS)

    Ochs, M.; Horbach, T.; Schulz, A.; Koch, R.; Bauer, H.-J.

    2009-07-01

    In heat transfer measurements with highly non-uniform wall heat fluxes, high spatial resolution of wall temperatures is required to fully capture the complex thermal situation. Infrared thermography systems provide that spatial resolution. To meet the thermal accuracy, they are usually calibrated in situ using thermocouples embedded in the test surface, which have to cover the complete temperature range of interest. However, thermocouples which are placed in regions of high temperature and heat flux gradients often cannot be used for the calibration and the overall accuracy of the calibration decreases significantly. Therefore, in the present work a novel in situ calibration method is presented which does not require thermocouples over the complete surface temperature range. The number of free parameters of the calibration function is reduced by an optimized insensitivity of the system with respect to changes in operating conditions. Reference measurements demonstrate the advantages of the new method.

  3. Evaluation of thermal load during laser corneal refractive surgery using infrared thermography

    NASA Astrophysics Data System (ADS)

    Brunsmann, U.; Sauer, U.; Arba-Mosquera, S.; Magnago, T.; Triefenbach, N.

    2010-09-01

    Infrared thermography is used for evaluation of the mean temperature as a measure of thermal load during corneal refractive surgery. An experimental method to determine emissivity and to calibrate the thermografic system is presented. In a case study on the porcine eye two dimensional temperature distributions with lateral resolution of 170 μm and line scans with temporal resolution of 13 μs are discussed with respect to the meaning of mean temperature. Using the newest generation of surgery equipment it is shown, that the mean temperature rise can be kept below 5 °C during myopic laser in situ keratomileusis (LASIK) treatments corresponding to an aberration-free correction of -2.75 diopter.

  4. Heat flow characterization and baseline of sandstone using infra-red thermography

    NASA Astrophysics Data System (ADS)

    Ibrahim, Y.; Padmanabhan, E.; Ano, A. B.; Ismail, W.

    2016-11-01

    Infra-red thermography was applied to sandstone to characterize and obtain a baseline or a reference thermal image for sandstone. The sample was imaged at room temperature and then heated and imaged again at different time intervals. The thermal images and the optical gradient obtained were analyzed, calibrated, and equated to actual-temperature measured geothermal gradient under controlled heat flux. Heat flow propagation is not consistent in the first time intervals (below 25 minutes). However, after that, the difference in temperature in the distal part and the proximal parts to the heat source almost remained constant. In general, the heat flow could fit to a linear model that is directly proportional to time. The results can be useful when applied to borehole thermal imaging, as well as in thermal conductivity and geothermal gradient determination.

  5. Comparative study for the nondestructive testing of advanced ceramic materials by infrared thermography and holographic interferometry

    NASA Astrophysics Data System (ADS)

    Sfarra, S.; Ibarra-Castanedo, C.; Bendada, A.; Maldague, X.; Ambrosini, D.; Paoletti, D.

    2010-05-01

    Advanced ceramic materials are increasingly employed in varied and new applications where improved electrical, mechanical and/or thermal properties are sought. For instance, in a manner similar to carbon or glass fiber reinforced plastics, ceramic matrix composites (CMCs) are designed to improve the naturally brittle characteristics of monolithic ceramics thanks to the inclusion of fibers. Among the main interests for advanced ceramics are the increase in the operation temperature of components, the elimination of the use of cooling fluids, and weight savings. In this paper, the capabilities of infrared thermography and holographic interferometry are investigated and compared for the nondestructive assessment of advanced ceramic materials using three experimental specimens: (1) a monolithic green ceramic tile with fabricated defects, (2) a CMC specimen (from production reject) with a porous alumina matrix reinforced with glass fibers, and (3) a sandwich structure consisting on a carbon fiber honeycomb core with a ceramic plate bonded in one side.

  6. In-flight investigations of the unsteady behaviour of the boundary layer with infrared thermography

    NASA Astrophysics Data System (ADS)

    Szewczyk, Mariusz; Smusz, Robert; de Groot, Klaus; Meyer, Joerg; Kucaba-Pietal, Anna; Rzucidlo, Pawel

    2017-04-01

    Infrared thermography (IRT) has been well established in wind tunnel and flight tests for the last decade. Former applications of IRT were focused, in nearly all cases, on steady measurements. In the last years, requirements of unsteady IRT measurements (up to 10 Hz) have been formulated, but the problem of a very slow thermal response of common materials of wind tunnel models or airplane components has to be overcome by finding a surface modification with a fast thermal response (low heat capacity, low thermal conductivity and high thermal diffusivity). Therefore, lab investigations of potential material combinations and flight tests with a ‘low cost’ aircraft, i.e. a glider with a modified wing surface, were conducted. In order to induce unsteady conditions (rapid change of laminar-turbulent boundary layer transition), special maneuvers of a glider during IRT measurements were performed.

  7. Characterization of defects situated in a fresco by stimulated infrared thermography

    NASA Astrophysics Data System (ADS)

    Candoré, J. C.; Bodnar, J. L.; Detalle, V.; Grossel, P.

    2012-01-01

    The objective of this work is to approach the possibilities of stimulated infrared thermography in dimensional characterization of defects situated in mural paintings. Towards this end, we have proceeded in two stages. Initially, we have developed, with the help of a point source photothermal analysis, an in situ measurement of the longitudinal thermal diffusivity parameter. Then, we have proceeded to the characterization of the depth of the studied defect, by means of a wide photothermal analysis and of a confrontation between theory and experiment. In this article, we present these two measurement techniques and show that the approach allows a good estimation of the depth of an inclusion of plastazote in a copy of the "Saint Christophe" of the "Campana" collection of the "Louvre Museum".

  8. Infrared thermography of the udder after experimentally induced Escherichia coli mastitis in cows.

    PubMed

    Metzner, Moritz; Sauter-Louis, Carola; Seemueller, Andrea; Petzl, Wolfram; Zerbe, Holm

    2015-06-01

    The study aimed to use infrared thermography (IRT) to evaluate the changes in udder surface temperature after induction of Escherichia coli mastitis in the right hind quarter. Over a time period of 24 h before to 24 h post-inoculation, thermograms of both hind quarters were taken every 2 h to determine maximum (Tmax) and average (Tavg) temperatures. Differences in both maximum and average temperatures (DTmax and DTavg) were calculated, as well as temperature differences between both hind quarters. All cows developed signs of clinical mastitis with a significant increase in DTmax and DTavg with Tmax at 13 h post-inoculation for the (non-infected) left hind quarters. The results demonstrate that detection of mastitis using IRT is possible if the interval between examinations does not exceed 2 h.

  9. Defect Detection in Fuel Cell Gas Diffusion Electrodes Using Infrared Thermography

    SciTech Connect

    Ulsh, Michael; Porter, Jason M.; Bittinat, Daniel C.; Bender, Guido

    2016-04-01

    Polymer electrolyte membrane fuel cells are energy conversion devices that offer high power densities and high efficiencies for mobile and other applications. Successful introduction into the marketplace requires addressing cost barriers such as production volumes and platinum loading. For cost reduction, it is vital to minimize waste and maximize quality during the manufacturing of platinum-containing electrodes, including gas diffusion electrodes (GDEs). In this work, we report on developing a quality control diagnostic for GDEs, involving creating an ex situ exothermic reaction on the electrode surface and using infrared thermography to measure the resulting temperature profile. Experiments with a moving GDE containing created defects were conducted to demonstrate the applicability of the diagnostic for real-time web-line inspection.

  10. LATERAL HEAT FLOW INFRARED THERMOGRAPHY FOR THICKNESS INDEPENDENT DETERMINATION OF THERMAL DIFFUSIVITY IN CFRP

    SciTech Connect

    Tralshawala, Nilesh; Howard, Don; Knight, Bryon; Plotnikov, Yuri; Ringermacher, Harry

    2008-02-28

    In conventional infrared thermography, determination of thermal diffusivity requires thickness information. Recently GE has been experimenting with the use of lateral heat flow to determine thermal diffusivity without thickness information. This work builds on previous work at NASA Langley and Wayne State University but we incorporate thermal time of flight (tof) analysis rather than curve fitting to obtain quantitative information. We have developed appropriate theoretical models and a tof based data analysis framework to experimentally determine all components of thermal diffusivity from the time-temperature measurements. Initial validation was carried out using finite difference simulations. Experimental validation was done using anisotropic carbon fiber reinforced polymer (CFRP) composites. We found that in the CFRP samples used, the in-plane component of diffusivity is about eight times larger than the through-thickness component.

  11. Non-destructive testing of works of art by stimulated infrared thermography

    NASA Astrophysics Data System (ADS)

    Candoré, J. C.; Bodnar, J. L.; Detalle, V.; Grossel, P.

    2012-02-01

    In this work, we present various examples of assistance to the restoration of works of art by stimulated infrared thermography. We show initially that the method allows the detection of delamination located in mural paintings, such as in the "Saint Christophe" of the Campana collection of the Louvre French museum. We show then that it also makes it possible to detect delaminations or galleries of worms in marquetries. We show in a third stage that it provides for the detection of detachment of grayness in stained glasses. We show in a fourth stage that it allows the visualization of shards or metal inserts located in a Greek "panathénaque" amphora of the French National museum of the Ceramics of Sevres. We show finally, that the method permits the detection of a crack located in an ovoid vase of the same French National museum of the Ceramics of Sevres.

  12. Neonatal non-contact respiratory monitoring based on real-time infrared thermography

    PubMed Central

    2011-01-01

    Background Monitoring of vital parameters is an important topic in neonatal daily care. Progress in computational intelligence and medical sensors has facilitated the development of smart bedside monitors that can integrate multiple parameters into a single monitoring system. This paper describes non-contact monitoring of neonatal vital signals based on infrared thermography as a new biomedical engineering application. One signal of clinical interest is the spontaneous respiration rate of the neonate. It will be shown that the respiration rate of neonates can be monitored based on analysis of the anterior naris (nostrils) temperature profile associated with the inspiration and expiration phases successively. Objective The aim of this study is to develop and investigate a new non-contact respiration monitoring modality for neonatal intensive care unit (NICU) using infrared thermography imaging. This development includes subsequent image processing (region of interest (ROI) detection) and optimization. Moreover, it includes further optimization of this non-contact respiration monitoring to be considered as physiological measurement inside NICU wards. Results Continuous wavelet transformation based on Debauches wavelet function was applied to detect the breathing signal within an image stream. Respiration was successfully monitored based on a 0.3°C to 0.5°C temperature difference between the inspiration and expiration phases. Conclusions Although this method has been applied to adults before, this is the first time it was used in a newborn infant population inside the neonatal intensive care unit (NICU). The promising results suggest to include this technology into advanced NICU monitors. PMID:22243660

  13. The uses of infrared thermography to evaluate the effects of climatic variables in bull's reproduction

    NASA Astrophysics Data System (ADS)

    Menegassi, Silvio Renato Oliveira; Pereira, Gabriel Ribas; Dias, Eduardo Antunes; Koetz, Celso; Lopes, Flávio Guiselli; Bremm, Carolina; Pimentel, Concepta; Lopes, Rubia Branco; da Rocha, Marcela Kuczynski; Carvalho, Helena Robattini; Barcellos, Júlio Otavio Jardim

    2016-01-01

    The objective of this study was to evaluate the seasonal effects of the environment on sperm quality in subtropical region determined by temperature and humidity index (THI). We used 20 Brangus bulls (5/8 Angus × 3/8 Nellore) aged approximately 24 months at the beginning of the study. Semen evaluations were performed twice per season during 1 year. Climate THI data were collected from an automatic weather station from the National Institute of Meteorology. Infrared thermography images were used to determine the temperature of the proximal and distal poles of the testis to assess the testicular temperature gradient (TG). The seasonal effects on seminal and climatic variables were analyzed with ANOVA using MIXED procedure of SAS. Sperm motility in spring (60.1 %), summer (57.6 %), and autumn (64.5 %) showed difference compared to winter (73.0 %; P < 0.01). TG was negatively correlated with THI at 18 days (spermiogenesis) (-0.76; P < 0.05) and at 12 days (epididymal transit) (-0.85; P < 0.01). Ocular temperature (OcT) had a positive correlation with THI at 18 days (0.78; P < 0.05) and at 12 days (0.84; P < 0.01). Motility showed a negative correlation with THI only at 18 days (-0.79; P < 0.05). During spermiogenesis, the TG had higher negative correlation compared to OcT (-0.97; P < 0.01) and rectal temperature (-0.72; P < 0.05). Spermatozoa with distal midpiece reflex were correlated with THI during transit epididymis (0.72; P < 0.05). Seminal parameters are not affected when THI reaches 93.0 (spermiogenesis) and 88.0 (epididymal transit). We concluded that infrared thermography can be adopted as an indirect method in order to assess the effect of environmental changes in TG and OcT of Brangus bulls.

  14. [Objective assessment of facial paralysis using infrared thermography and formal concept analysis].

    PubMed

    Liu, Xu-Long; Hong, Wen-Xue; Liu, Jie-Min

    2014-04-01

    This paper presented a novel approach to objective assessment of facial nerve paralysis based on infrared thermography and formal concept analysis. Sixty five patients with facial nerve paralysis on one side were included in the study. The facial temperature distribution images of these 65 patients were captured by infrared thermography every five days during one-month period. First, the facial thermal images were pre-processed to identify six potential regions of bilateral symmetry by using image segmentation techniques. Then, the temperature differences on the left and right sides of the facial regions were extracted and analyzed. Finally, the authors explored the relationships between the statistical averages of those temperature differences and the House-Brackmann score for objective assessment degree of nerve damage in a facial nerve paralysis by using formal concept analysis. The results showed that the facial temperature distribution of patients with facial nerve paralysis exhibited a contralateral asymmetry, and the bilateral temperature differences of the facial regions were greater than 0.2 degrees C, whereas in normal healthy individuals these temperature differences were less than 0.2 degrees C. Spearman correlation coefficient between the bilateral temperature differences of the facial regions and the degree of facial nerve damage was an average of 0.508, which was statistically significant (p < 0.05). Furthermore, if one of the temperature differences of bilateral symmetry on facial regions was greater than 0.2 degrees C, and all were less than 0.5 degrees C, facial nerve paralysis could be determined as for the mild to moderate; if one of the temperature differences of bilateral symmetry was greater than 0.5 degrees C, facial nerve paralysis could be determined as for serious. In conclusion, this paper presents an automated technique for the computerized analysis of thermal images to objectively assess facial nerve related thermal dysfunction by

  15. Concentration of mycotoxins and chemical composition of corn silage: a farm survey using infrared thermography.

    PubMed

    Schmidt, P; Novinski, C O; Junges, D; Almeida, R; de Souza, C M

    2015-09-01

    This work evaluated the chemical composition and mycotoxin incidence in corn silage from 5 Brazilian dairy-producing regions: Castro, in central-eastern Paraná State (n=32); Toledo, in southwestern Paraná (n=20); southeastern Goiás (n=14); southern Minas Gerais (n=23); and western Santa Catarina (n=20). On each dairy farm, an infrared thermography camera was used to identify 3 sampling sites that exhibited the highest temperature, a moderate temperature, and the lowest temperature on the silo face, and 1 sample was collected from each site. The chemical composition and concentrations of mycotoxins were evaluated, including the levels of aflatoxins B1, B2, G1, and G2; zearalenone; ochratoxin A; deoxynivalenol; and fumonisins B1 and B2. The corn silage showed a highly variable chemical composition, containing, on average, 7.1±1.1%, 52.5±5.4%, and 65.2±3.6% crude protein, neutral detergent fiber, and total digestible nutrients, respectively. Mycotoxins were found in more than 91% of the samples, with zearalenone being the most prevalent (72.8%). All samples from the Castro region contained zearalenone at a high average concentration (334±374µg/kg), even in well-preserved silage. The incidence of aflatoxin B1 was low (0.92%). Silage temperature and the presence of mycotoxins were not correlated; similarly, differences were not observed in the concentration or incidence of mycotoxins across silage locations with different temperatures. Infrared thermography is an accurate tool for identifying heat sites, but temperature cannot be used to predict the chemical composition or the incidence of mycotoxins that have been analyzed, within the silage. The pre-harvest phase of the ensiling process is most likely the main source of mycotoxins in silage.

  16. Infrared thermography fails to visualize stimulation-induced meridian-like structures: comment by Rixin Chen and Zhimai Lv and reply from Gerhard Litscher

    PubMed Central

    2011-01-01

    A comment on G. Litscher: Infrared thermography fails to visualize stimulation-induced meridian-like structures. Biomed. Eng. OnLine 2005, 4:38 (15 June 2005), with a response by the author. PMID:21906400

  17. Low-temperature infiltration identified using infrared thermography in patients with subcutaneous edema revealed ultrasonographically: A case report.

    PubMed

    Oya, Maiko; Takahashi, Toshiaki; Tanabe, Hidenori; Oe, Makoto; Murayama, Ryoko; Yabunaka, Koichi; Matsui, Yuko; Sanada, Hiromi

    Infiltration is a frequent complication of infusion therapy. We previously demonstrated the usefulness of infrared thermography as an objective method of detecting infiltration in healthy people. However, whether thermography can detect infiltration in clinical settings remains unknown. Therefore, we report two cases where thermography was useful in detecting infiltration at puncture sites. In both cases, tissue changes were verified ultrasonographically. The patients were a 56-year-old male with cholangitis and a 76-year-old female with hepatoma. In both cases, infiltration symptoms such as swelling and erythema occurred one day after the insertion of a peripheral intravenous catheter. Thermographic images from both patients revealed low-temperature areas spreading from the puncture sites; however, these changes were not observed in other patients. The temperature difference between the low-temperature areas and their surrounding skin surface exceeded 1.0°C. Concurrently, ultrasound images revealed that tissues surrounding the vein had a cobblestone appearance, indicating edema. In both patients, subcutaneous tissue changes suggested infiltration and both had low-temperature areas spreading from the puncture sites. Thus, subcutaneous edema may indicate infusion leakage, resulting in a decrease in the temperature of the associated skin surface. These cases suggest that infrared thermography is an effective method of objectively and noninvasively detecting infiltration.

  18. A novel intelligent fault diagnosis method for electrical equipment using infrared thermography

    NASA Astrophysics Data System (ADS)

    Zou, Hui; Huang, Fuzhen

    2015-11-01

    Infrared thermography (IRT) has taken a very important role in monitoring and inspecting thermal defects of electrical equipment without shutting down, which has important significance for the stability of power systems. It has many advantages such as non-contact detection, freedom from electromagnetic interference, safety, reliability and providing large inspection coverage. Manual analysis of infrared images for detecting defects and classifying the status of equipment may take a lot of time and efforts, and may also lead to incorrect diagnosis results. To avoid the lack of manual analysis of infrared images, many intelligent fault diagnosis methods for electrical equipment are proposed, but there are two difficulties when using these methods: one is to find the region of interest, another is to extract features which can represent the condition of electrical equipment, as it is difficult to segment infrared images due to their over-centralized distributions and low intensity contrasts, which are quite different from those in visual light images. In this paper, a new intelligent diagnosis method for classification different conditions of electrical equipment using data obtained from infrared images is presented. In the first stage of our method, an infrared image of electrical equipment is clustered using K-means algorithm, then statistical characteristics containing temperature and area information are extracted in each region. In the second stage, in order to select the salient features which can better represent the condition of electrical equipment, some or all statistical characteristics from each region are combined as input data for support vector machine (SVM) classifier. To improve the classification performance of SVM, a coarse-to-fine parameter optimization approach is adopted. The performance of SVM is compared with that of back propagation neural network. The comparison results show that our method can achieve a better performance with accuracy 97.8495%.

  19. Application of on-line infrared thermography in steel making industry

    NASA Astrophysics Data System (ADS)

    Viale, M.; Martin, O.; Muratori, F.; Bertezzolo, U.; Perez, J.; Usart, J.

    2007-04-01

    This work is about three real applications in the steel industry where the infrared technology is used to control the process and to increase safety. All the applications where developed by Ternium-Siderar automation group. The main objectives are to use the infrared thermography in steel plant are to reduce production costs and to prevent mayor damages. The first work is about automatic slag detection during the tapping operation of the Blast Oxygen Furnace (BOF) converters by thermographical image processing. The benefit is to reduce fluxes due to less slag carryover and also to eliminate the ladle recirculation for excessive slag. Additionally, the steel shop process engineers are using the camera information to estimate some other process variables. There is a project to make all the BOF tapping fully automatic, using the camera information. The second work is about on-line ladle hot spot detection. A failure of the ladle refractory bricks may cause damages in the ladle car, mechanical equipment, and cabling in the ladle furnace. To detect these failures, a system of four infrared cameras with an image processing software was developed. Also in future applications, the thermal information is going to be used for data correlation with other process variables. The third one is in the sinter plant, where the camera temperature information is used to optimize the process control. Before the system installation, there was no available information about the sinter material temperature. Nowadays there is an on-line information that is used to close the control loop.

  20. Use of infrared thermography in children with shock: A case series.

    PubMed

    Ortiz-Dosal, Alejandra; Kolosovas-Machuca, Eleazar S; Rivera-Vega, Rosalina; Simón, Jorge; González, Francisco J

    2014-01-01

    Shock is a complex clinical syndrome caused by an acute failure of circulatory function resulting in inadequate tissue and organ perfusion. Digital infrared thermal imaging is a non-invasive technique that can detect changes in blood perfusion by detecting small changes in the temperature of the skin. In this preliminary study, eight pediatric patients (five boys, three girls), ages ranging from 6 to 14 years (average: 9.8 years), were admitted to the Intensive Care Unit at "Dr. Ignacio Morones Prieto" Central Hospital; here, the patients were examined using digital infrared thermal imaging. Patients in shock showed a significant decrease in distal temperature (at least 7°), compared to critically ill patients without shock. The latter group presented a skin temperature pattern very similar to the one previously reported for healthy children. The results show that infrared thermography can be used as a non-invasive method for monitoring the temperature in pediatric patients in intensive care units in order to detect shock in its early stages.

  1. Precise Temperature Mapping of GaN-Based LEDs by Quantitative Infrared Micro-Thermography

    PubMed Central

    Chang, Ki Soo; Yang, Sun Choel; Kim, Jae-Young; Kook, Myung Ho; Ryu, Seon Young; Choi, Hae Young; Kim, Geon Hee

    2012-01-01

    A method of measuring the precise temperature distribution of GaN-based light-emitting diodes (LEDs) by quantitative infrared micro-thermography is reported. To reduce the calibration error, the same measuring conditions were used for both calibration and thermal imaging; calibration was conducted on a highly emissive black-painted area on a dummy sapphire wafer loaded near the LED wafer on a thermoelectric cooler mount. We used infrared thermal radiation images of the black-painted area on the dummy wafer and an unbiased LED wafer at two different temperatures to determine the factors that degrade the accuracy of temperature measurement, i.e., the non-uniform response of the instrument, superimposed offset radiation, reflected radiation, and emissivity map of the LED surface. By correcting these factors from the measured infrared thermal radiation images of biased LEDs, we determined a precise absolute temperature image. Consequently, we could observe from where the local self-heat emerges and how it distributes on the emitting area of the LEDs. The experimental results demonstrated that highly localized self-heating and a remarkable temperature gradient, which are detrimental to LED performance and reliability, arise near the p-contact edge of the LED surface at high injection levels owing to the current crowding effect. PMID:22666050

  2. Use of infrared thermography in children with shock: A case series

    PubMed Central

    Ortiz-Dosal, Alejandra; Rivera-Vega, Rosalina; Simón, Jorge; González, Francisco J

    2014-01-01

    Shock is a complex clinical syndrome caused by an acute failure of circulatory function resulting in inadequate tissue and organ perfusion. Digital infrared thermal imaging is a non-invasive technique that can detect changes in blood perfusion by detecting small changes in the temperature of the skin. In this preliminary study, eight pediatric patients (five boys, three girls), ages ranging from 6 to 14 years (average: 9.8 years), were admitted to the Intensive Care Unit at “Dr. Ignacio Morones Prieto” Central Hospital; here, the patients were examined using digital infrared thermal imaging. Patients in shock showed a significant decrease in distal temperature (at least 7°), compared to critically ill patients without shock. The latter group presented a skin temperature pattern very similar to the one previously reported for healthy children. The results show that infrared thermography can be used as a non-invasive method for monitoring the temperature in pediatric patients in intensive care units in order to detect shock in its early stages. PMID:27489669

  3. Using lock-in infrared thermography for the visualization of the hand vascular tree

    NASA Astrophysics Data System (ADS)

    Bouzida, Nabila; Bendada, Abdel Hakim; Piau, Jean-Marc; Akhloufi, Moulay; Maldague, Xavier; Raymond, Mathieu

    2008-03-01

    An imaging technique of the hand vein tree is presented in this paper. Using the natural human circulatory system and a controlled armband pressure around the arm, a lock-in thermography technique with an internal excitation is carried out. Since the stimulation frequency is inversely proportional to the inspection depth, the subcutaneous layer requires the use of a very slow frequency. Thus, a sawtooth waveform is preferred to minimize the duration of the pressure applied to the armband during the experiment. A frequency of approximately 0.03 Hz and a pressure range between 100 and 140 mmHg, according to the diastolic and systolic blood pressure, are used as stimulation. Then, dorsal hand amplitude and phase images are obtained with IR_view (Klein, 1999), a tool specifically designed to analyze infrared images. The hand vein structure is thermally mapped by an infrared camera operating in the middle wavelength infrared range (MWIR) at room temperature. Parasitic frequencies are avoided by keeping the hand fixed. The resulting images show a gradient of temperature between surrounding tissues and the back-of-hand veins. The vascular signature segmentation is extracted from the amplitude and phase images by using a Fast Fourier Transform image processing technique. This work could be used for vein localization for perfusion or for the early diagnosis of vein diseases such as primitive varicose and deep vein thrombosis (DVT). A hand vein signature database for identification purposes is also possible.

  4. Real Time Detection of Defects in GFRP Bridge Decks Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Klinkhachorn, P.; Lonkar, G. M.; Halabe, Udaya B.; GangaRao, Hota V. S.

    2006-03-01

    This work is aimed at building a real time system to detect subsurface defects in GFRP bridge decks using infrared thermography. The issues addressed are: (a) development of a real time defect detection system, and (b) image mosaicking to build a composite image map. In the tests conducted, a turn key system was built in Matlab environment using the FLIR SDK to acquire image from the ThermaCAM S60 infrared camera. The images were then analyzed by defect detection algorithms. Efforts were made to minimize the time to detect defects in a captured image. In the second phase, image mosaicking was used to build a "composite image" that combines all the infrared images to form a single image. The location of defects in the "composite image" leads to a system that will be able to point out defects in the bridge as a whole. The study creates a base that can be used for real time defect detection in GFRP bridge decks.

  5. Infrared Thermography-based Biophotonics: Integrated Diagnostic Technique for Systemic Reaction Monitoring

    NASA Astrophysics Data System (ADS)

    Vainer, Boris G.; Morozov, Vitaly V.

    A peculiar branch of biophotonics is a measurement, visualisation and quantitative analysis of infrared (IR) radiation emitted from living object surfaces. Focal plane array (FPA)-based IR cameras make it possible to realize in medicine the so called interventional infrared thermal diagnostics. An integrated technique aimed at the advancement of this new approach in biomedical science and practice is described in the paper. The assembled system includes a high-performance short-wave (2.45-3.05 μm) or long-wave (8-14 μm) IR camera, two laser Doppler flowmeters (LDF) and additional equipment and complementary facilities implementing the monitoring of human cardiovascular status. All these means operate synchronously. It is first ascertained the relationship between infrared thermography (IRT) and LDF data in humans in regard to their systemic cardiovascular reactivity. Blood supply real-time dynamics in a narcotized patient is first visualized and quantitatively represented during surgery in order to observe how the general hyperoxia influences thermoregulatory mechanisms; an abrupt increase in temperature of the upper limb is observed using IRT. It is outlined that the IRT-based integrated technique may act as a take-off runway leading to elaboration of informative new methods directly applicable to medicine and biomedical sciences.

  6. A preliminary biomechanical assessment of a polymer composite hip implant using an infrared thermography technique validated by strain gage measurements.

    PubMed

    Bougherara, Habiba; Rahim, Ehsan; Shah, Suraj; Dubov, Anton; Schemitsch, Emil H; Zdero, Rad

    2011-07-01

    With the resurgence of composite materials in orthopaedic applications, a rigorous assessment of stress is needed to predict any failure of bone-implant systems. For current biomechanics research, strain gage measurements are employed to experimentally validate finite element models, which then characterize stress in the bone and implant. Our preliminary study experimentally validates a relatively new nondestructive testing technique for orthopaedic implants. Lock-in infrared (IR) thermography validated with strain gage measurements was used to investigate the stress and strain patterns in a novel composite hip implant made of carbon fiber reinforced polyamide 12 (CF/PA12). The hip implant was instrumented with strain gages and mechanically tested using average axial cyclic forces of 840 N, 1500 N, and 2100 N with the implant at an adduction angle of 15 deg to simulate the single-legged stance phase of walking gait. Three-dimensional surface stress maps were also obtained using an IR thermography camera. Results showed almost perfect agreement of IR thermography versus strain gage data with a Pearson correlation of R(2) = 0.96 and a slope = 1.01 for the line of best fit. IR thermography detected hip implant peak stresses on the inferior-medial side just distal to the neck region of 31.14 MPa (at 840 N), 72.16 MPa (at 1500 N), and 119.86 MPa (at 2100 N). There was strong correlation between IR thermography-measured stresses and force application level at key locations on the implant along the medial (R(2) = 0.99) and lateral (R(2) = 0.83 to 0.99) surface, as well as at the peak stress point (R(2) = 0.81 to 0.97). This is the first study to experimentally validate and demonstrate the use of lock-in IR thermography to obtain three-dimensional stress fields of an orthopaedic device manufactured from a composite material.

  7. Computerized tomography technique for reconstruction of obstructed temperature field in infrared thermography

    NASA Astrophysics Data System (ADS)

    Sham, F. C.; Huang, Y. H.; Liu, L.; Chen, Y. S.; Hung, Y. Y.; Lo, T. Y.

    2010-01-01

    Infrared thermography is a rapid, non-invasive and full-field technique for non-destructive testing and evaluation (NDT&E). With all the achievements on IR instrumentation and image processing techniques attained, it has been extended far beyond simple hot-spot detection and becomes one of the most promising NDT&E techniques in the last decades. It has achieved increasing acceptance in different sectors include medical imaging, manufacturing component fault detection and buildings diagnostic. However, one limitation of IR thermography is that the testing results are greatly affected by object surface emissivity. Surface with various emissivities may lead to difficult discrimination between area of defect and area with different emissivity. Therefore, many studies have been carried out on eliminating emissivity, for example, the time derivative approach, lock-in processing and differential contrast measurements. In these methods, sequence of themo-data/images are recorded and being processed in order to eliminate differences of emissivity. Another problem of IR thermography is that any obstruction may limit stimulations and imaging which leads to the observation of unclear defect image. To solve this problem, this paper proposes an algorithm based on the principle of computerized tomography which permits the reconstruction of unavailable/partially available temperature distribution of the affected area using the measured surrounding temperature field. In the process, a set of imaginary rays are projected from many different directions across the area. For each ray, integration of the temperature derivatives along the ray is equals to the temperature difference between the boundary points intercepted by the ray. Therefore, a set of linear equations can be established by considering the multiple rays. Each equation expresses the unknown temperature derivatives in the affected area in terms of the measured boundary temperature data. Solution of the set of simultaneous

  8. Use of infrared thermography for the diagnosis and grading of sprained ankle injuries

    NASA Astrophysics Data System (ADS)

    Oliveira, João; Vardasca, Ricardo; Pimenta, Madalena; Gabriel, Joaquim; Torres, João

    2016-05-01

    Ankle joint sprains are a common medical condition estimated to be responsible for 15-25% of all musculoskeletal injuries worldwide. The pathophysiology of the lesion can represent considerable time lost to injury, as well as long-term disability in up to 60% of patients. A percentage between 10% and 20% may complicate with chronic instability of the ankle joint and disability in walking, contributing to morbidity and poor life quality. Ankle sprains can be classified as grade I, II, or III, based on the extent of damage and number of ligaments affected. The diagnostic grading is important for setting further treatment and rehabilitation, since more severe injuries carries risk of recurrence, added morbidity and decrease in life quality. The aim of this work was to evaluate the adequacy of infrared thermography as a potential complimentary diagnostic tool of the distinct lesions grades. Evaluation of different thermographic values of the ankle region (in both affected and non-affected foot) was conducted for this purpose. The principal results to be highlighted are that some of the regions, namely anterior view for non defined time after injury analysis, and anterior, frontal, posterior and anterior talofibular ligament regions and proximal calcaneofibular ligament regions in acute lesions (herein defined as less than 6 h post-traumatic event) presented consistent profiles of variation. The analyses were performed considering affected and non-affected ankles results on plotted graphics representing termographic evaluation and grading of these lesions performed using ultrasound by experimented medical radiologists. An increase in temperature values was observed when progressing from mild to severe ankle sprain injuries, with these regions presenting lower values for the affected ankle when compared to the non-affected ankle in all the analysis performed. The remaining analysed regions did not present the same variations. Statistical analysis using Kruskal

  9. Infrared thermography for examination of skin temperature in the dorsal hand of office workers.

    PubMed

    Gold, Judith E; Cherniack, Martin; Buchholz, Bryan

    2004-10-01

    Reduced blood flow may contribute to the pathophysiology of upper extremity musculoskeletal disorders (UEMSD), such as tendinitis and carpal tunnel syndrome. The study objective was to characterize potential differences in cutaneous temperature, among three groups of office workers assessed by dynamic thermography following a 9-min typing challenge: those with UEMSD, with ( n=6) or without ( n=10) cold hands exacerbated by keyboard use, and control subjects ( n=12). Temperature images of the metacarpal region of the dorsal hand were obtained 1 min before typing, and during three 2-min sample periods [0-2 min (early), 3-5 min (middle), and 8-10 min (late)] after typing. Mean temperature increased from baseline levels immediately after typing by a similar magnitude, 0.7 (0.3) degrees C in controls and 0.6 (0.2) degrees C in UEMSD cases without cold hands, but only by 0.1 (0.3) degrees C in those with cold hands. Using paired t-tests for within group comparisons of mean dorsal temperature between successive imaging periods, three patterns of temperature change were apparent during 10 min following typing. Controls further increased mean temperature by 0.1 degrees C ( t-test, P=0.001) at 3-5 min post-typing before a late temperature decline of -0.3 degrees C ( t-test, P=0.04), while cases without cold hands showed no change from initial post-typing mean temperature rise during middle or late periods. In contrast, subjects with keyboard-induced cold hands had no change from initial post-typing temperature until a decrease at the late period of -0.3 degrees C ( t-test, P=0.06). Infrared thermography appears to distinguish between the three groups of subjects, with keyboard-induced cold hand symptoms presumably due, at least partially, to reduced blood flow.

  10. Diagnosis of response and non-response to dry eye treatment using infrared thermography images

    NASA Astrophysics Data System (ADS)

    Acharya, U. Rajendra; Tan, Jen Hong; Vidya, S.; Yeo, Sharon; Too, Cheah Loon; Lim, Wei Jie Eugene; Chua, Kuang Chua; Tong, Louis

    2014-11-01

    The dry eye treatment outcome depends on the assessment of clinical relevance of the treatment effect. The potential approach to assess the clinical relevance of the treatment is to identify the symptoms responders and non-responders to the given treatments using the responder analysis. In our work, we have performed the responder analysis to assess the clinical relevance effect of the dry eye treatments namely, hot towel, EyeGiene®, and Blephasteam® twice daily and 12 min session of Lipiflow®. Thermography is performed at week 0 (baseline), at weeks 4 and 12 after treatment. The clinical parameters such as, change in the clinical irritations scores, tear break up time (TBUT), corneal staining and Schirmer's symptoms tests values are used to obtain the responders and non-responders groups. We have obtained the infrared thermography images of dry eye symptoms responders and non-responders to the three types of warming treatments. The energy, kurtosis, skewness, mean, standard deviation, and various entropies namely Shannon, Renyi and Kapoor are extracted from responders and non-responders thermograms. The extracted features are ranked based on t-values. These ranked features are fed to the various classifiers to get the highest performance using minimum features. We have used decision tree (DT), K nearest neighbour (KNN), Naves Bayesian (NB) and support vector machine (SVM) to classify the features into responder and non-responder classes. We have obtained an average accuracy of 99.88%, sensitivity of 99.7% and specificity of 100% using KNN classifier using ten-fold cross validation.

  11. Vibration characteristics measurement of beam-like structures using infrared thermography

    NASA Astrophysics Data System (ADS)

    Talai, S. M.; Desai, D. A.; Heyns, P. S.

    2016-11-01

    Infrared thermography (IRT) has matured and is now widely accepted as a condition monitoring tool where temperature is measured in a non-contact way. Since the late 1970s, it has been extensively used in vibrothermography (Sonic IR) non-destructive technique for the evaluation of surface cracks through the observation of thermal imaging of the vibration-induced crack heat generation. However, it has not received research attention on prediction of structural vibration behaviour, hence; the concept to date is not understood. Therefore, this paper explores its ability to fill the existing knowledge gap. To achieve this, two cantilever beam-like structures couple with a friction rod subjected to a forced excitations while infrared cameras capturing the thermal images on the friction interfaces. The analysed frictional temperature evolution using the Matlab Fast Fourier Transform (FFT) algorithm and the use of the heat conduction equation in conjunction with a finite difference approach successfully identifies the structural vibration characteristics; with maximum error of 0.28% and 20.71% for frequencies and displacements, respectively. These findings are particularly useful in overcoming many limitations inherent in some of the current vibration measuring techniques applied in structural integrity management such as strain gauge failures due to fatigue.

  12. Infrared thermography: A potential noninvasive tool to monitor udder health status in dairy cows.

    PubMed

    Sathiyabarathi, M; Jeyakumar, S; Manimaran, A; Jayaprakash, G; Pushpadass, Heartwin A; Sivaram, M; Ramesha, K P; Das, D N; Kataktalware, Mukund A; Prakash, M Arul; Kumar, R Dhinesh

    2016-10-01

    The animal husbandry and livestock sectors play a major role in the rural economy, especially for the small and marginal farmers. India has the largest livestock population in the world and ranks first in the milk production. Mastitis is the most common and expensive infectious disease in dairy cattle. The global economic losses per year due to mastitis amounts to USD 35 billion and for Indian dairy industry ₹6000 crores per year. Early detection of mastitis is very important to reduce the economic loss to the dairy farmers and dairy industry. Automated methods for early and reliable detection of mastitis are currently in focus under precision dairying. Skin surface temperature is an important indicator for the diagnosis of cow's illnesses and for the estimation of their physiological status. Infrared thermography (IRT) is a simple, effective, on-site, and noninvasive method that detects surface heat, which is emitted as infrared radiation and generates pictorial images without causing radiation exposure. In human and bovine medicine, IRT is used as a diagnostic tool for assessment of normal and physiological status.

  13. Infrared thermography: A potential noninvasive tool to monitor udder health status in dairy cows

    PubMed Central

    Sathiyabarathi, M.; Jeyakumar, S.; Manimaran, A.; Jayaprakash, G.; Pushpadass, Heartwin A.; Sivaram, M.; Ramesha, K. P.; Das, D. N.; Kataktalware, Mukund A.; Prakash, M. Arul; Kumar, R. Dhinesh

    2016-01-01

    The animal husbandry and livestock sectors play a major role in the rural economy, especially for the small and marginal farmers. India has the largest livestock population in the world and ranks first in the milk production. Mastitis is the most common and expensive infectious disease in dairy cattle. The global economic losses per year due to mastitis amounts to USD 35 billion and for Indian dairy industry ₹6000 crores per year. Early detection of mastitis is very important to reduce the economic loss to the dairy farmers and dairy industry. Automated methods for early and reliable detection of mastitis are currently in focus under precision dairying. Skin surface temperature is an important indicator for the diagnosis of cow’s illnesses and for the estimation of their physiological status. Infrared thermography (IRT) is a simple, effective, on-site, and noninvasive method that detects surface heat, which is emitted as infrared radiation and generates pictorial images without causing radiation exposure. In human and bovine medicine, IRT is used as a diagnostic tool for assessment of normal and physiological status. PMID:27847416

  14. Beam width estimation of microwave antennas using lock-in infrared thermography

    NASA Astrophysics Data System (ADS)

    Muzaffar, Khalid; Tuli, Suneet; Koul, Shiban

    2015-09-01

    The beam width of microwave antennas can be easily determined using infrared thermography. A thin absorption screen made up of some carbon loaded polymer is placed in front of a microwave antenna. The electromagnetic waves impinging the screen are partially absorbed by it, resulting in temperature rise of this screen. This temperature rise is monitored by an infrared camera. These infra red images of the temperature distribution are identical to the power distribution of the incident electromagnetic field at the screen location. The distance between half power points on the main lobe of the radiation pattern at the screen location in two orthogonal directions (E- and H-planes) can be easily found. From these distances the half power beam widths in both E- and H-planes can be calculated. Further from these beam widths, directivity is also calculated. The experiments were carried with a patch antenna radiating at 2.45 GHz. In order to show the repeatability of the results, experiments were carried for different distances between patch antenna and absorption screen. A great agreement is seen between simulation, measurement and experimental (thermographic) results. The microwave source is modulated at a low frequency so as to avoid the lateral spread of heat on the absorption screen and to permit lock-in detection of temperature distribution.

  15. Measurement of defect thickness of the wall thinning defect pipes by lock-in infrared thermography technique

    NASA Astrophysics Data System (ADS)

    Kim, Kyeongsuk; Kim, Kyungsu; Jung, Hyunchul; Chang, Hosub

    2009-12-01

    Mostly piping which is using for the nuclear power plants are made up of carbon steel pipes. The wall thinning defects occurs by the effect of the flow accelerated corrosion of fluid that flows in carbon steel pipes. The defects could be found on the welding part and anywhere in the pipes. The infrared thermography technique which is one of the non-destructive testing method has used for detecting the defects of various kinds of materials over the years. There is a limitation for measuring the defect of metals that have a big coefficient of thermal diffusion. However, a technique using lock-in method gets over the difficulty. Consequently, the lock-in infrared thermography technique has been applied to the various industry fields. In this paper, the defect thickness of the straight pipe which has an artificial defect the inside of the pipes was measured by using the lock-in infrared thermography technique and the result could be utilized in detecting defects of carbon steel pipes.

  16. Measurement of defect thickness of the wall thinning defect pipes by lock-in infrared thermography technique

    NASA Astrophysics Data System (ADS)

    Kim, Kyeongsuk; Kim, Kyungsu; Jung, Hyunchul; Chang, Hosub

    2010-03-01

    Mostly piping which is using for the nuclear power plants are made up of carbon steel pipes. The wall thinning defects occurs by the effect of the flow accelerated corrosion of fluid that flows in carbon steel pipes. The defects could be found on the welding part and anywhere in the pipes. The infrared thermography technique which is one of the non-destructive testing method has used for detecting the defects of various kinds of materials over the years. There is a limitation for measuring the defect of metals that have a big coefficient of thermal diffusion. However, a technique using lock-in method gets over the difficulty. Consequently, the lock-in infrared thermography technique has been applied to the various industry fields. In this paper, the defect thickness of the straight pipe which has an artificial defect the inside of the pipes was measured by using the lock-in infrared thermography technique and the result could be utilized in detecting defects of carbon steel pipes.

  17. Monitoring changes in skin temperature associated with exercise in horses on a water treadmill by use of infrared thermography.

    PubMed

    Yarnell, Kelly; Fleming, Jennifer; Stratton, Tim D; Brassington, Rebecca

    2014-10-01

    Infrared thermography (IRT) was used to assess surface temperature change as an indirect measure of muscle activity and exercise associated changes in blood flow in the working hind limb muscles of horses (n=7) undergoing water treadmill exercise. Three treatments were investigated including the treadmill ran dry (TD), water at the height of the proximal interphalangeal joint (PIP) and water at the height of the carpus (CP). Maximum skin surface temperature was recorded from the region of the semitendinosus muscle during exercise at each water height. There was a significant difference in surface hind limb temperature between exercise on the water treadmill ran dry and with water at the height of the PIP and CP (P<0.0001) with hotter temperatures recorded during the TD treatment. There was a greater increase in surface temperature of the hind limbs from pre exercise to maximum temperature during the PIP and CP treatments when compared to the TD treatment, however, this was not significant (P=0.58). There was no significant difference in surface hind limb temperature found between exercise in water at the height of the PIP and water at the height of the CP. The findings from this study suggest that IRT is able to non-invasively detect muscle activity and associated changes in blood flow whilst horses are exercised on a water treadmill. IRT could potentially be used as an alternative method to assess muscle activity and temperature change in an aquatic environment where existing methods present methodological challenges.

  18. The uses of infrared thermography to evaluate the effects of climatic variables in bull's reproduction.

    PubMed

    Menegassi, Silvio Renato Oliveira; Pereira, Gabriel Ribas; Dias, Eduardo Antunes; Koetz, Celso; Lopes, Flávio Guiselli; Bremm, Carolina; Pimentel, Concepta; Lopes, Rubia Branco; da Rocha, Marcela Kuczynski; Carvalho, Helena Robattini; Barcellos, Júlio Otavio Jardim

    2016-01-01

    The objective of this study was to evaluate the seasonal effects of the environment on sperm quality in subtropical region determined by temperature and humidity index (THI). We used 20 Brangus bulls (5/8 Angus × 3/8 Nellore) aged approximately 24 months at the beginning of the study. Semen evaluations were performed twice per season during 1 year. Climate THI data were collected from an automatic weather station from the National Institute of Meteorology. Infrared thermography images were used to determine the temperature of the proximal and distal poles of the testis to assess the testicular temperature gradient (TG). The seasonal effects on seminal and climatic variables were analyzed with ANOVA using MIXED procedure of SAS. Sperm motility in spring (60.1%), summer (57.6%), and autumn (64.5%) showed difference compared to winter (73.0%; P < 0.01). TG was negatively correlated with THI at 18 days (spermiogenesis) (-0.76; P < 0.05) and at 12 days (epididymal transit) (-0.85; P < 0.01). Ocular temperature (OcT) had a positive correlation with THI at 18 days (0.78; P < 0.05) and at 12 days (0.84; P < 0.01). Motility showed a negative correlation with THI only at 18 days (-0.79; P < 0.05). During spermiogenesis, the TG had higher negative correlation compared to OcT (-0.97; P < 0.01) and rectal temperature (-0.72; P < 0.05). Spermatozoa with distal midpiece reflex were correlated with THI during transit epididymis (0.72; P < 0.05). Seminal parameters are not affected when THI reaches 93.0 (spermiogenesis) and 88.0 (epididymal transit). We concluded that infrared thermography can be adopted as an indirect method in order to assess the effect of environmental changes in TG and OcT of Brangus bulls.

  19. Infrared thermography detects febrile and behavioural responses to vaccination of weaned piglets.

    PubMed

    Cook, N J; Chabot, B; Lui, T; Bench, C J; Schaefer, A L

    2015-02-01

    An automated, non-invasive system for monitoring of thermoregulation has the potential to mitigate swine diseases through earlier detection. Measurement of radiated temperature of groups of animals by infrared thermography (IRT) is an essential component of such a system. This study reports on the feasibility of monitoring the radiated temperature of groups of animals as a biomarker of immune response using vaccination as a model for febrile disease. In Study A, weaned pigs were either treated with an intramuscular vaccine (FarrowSure Gold), a sham injection of 0.9% saline or left as untreated controls. An infrared thermal camera (FLIR A320) was fixed to the ceiling directly above the pen of animals, and recorded infrared images of the treatment groups at 5 min intervals. The effect on temperature of the spatial distribution of pigs within the pen was significant, with higher temperatures recorded when pigs were grouped together into a single cluster. A higher frequency of clustering behaviour was observed in vaccinated animals compared with controls during a period of the afternoon ~4 to 7 h post-vaccination. The daily mean of the maximum image temperature was significantly higher in vaccinated animals compared with control and sham-treated animals. In the vaccination treated group, the 24 h mean of the maximum temperature was significantly higher during the post-vaccination period compared with the 24 h period before vaccination. Increased temperature in the vaccinated animals occurred from ~3 h, peaked at ~10 h, and remained elevated for up to 20 h post-vaccination. In Study B, the effect of prevalence was tested in terms of the difference in maximum temperature between control and vaccination days. A thermal response to vaccination was detected in a pen of 24 to 26 animals when <10% of the animals were vaccinated. The results support the concept of radiated temperature measurements of groups of animals by IRT as a screening tool for febrile diseases in pig

  20. The Use of Infrared Thermography for Porosity Assessment of Intact Rock

    NASA Astrophysics Data System (ADS)

    Mineo, S.; Pappalardo, G.

    2016-08-01

    Preliminary results on a new test for the indirect assessment of porosity through infrared thermography are presented. The study of the cooling behavior of rock samples in laboratory, through the analysis of thermograms, proved an innovative tool for the estimation of such an important property, which is one of the main features affecting the mechanical behavior of rocks. A detailed experimentation was performed on artificially heated volcanic rock samples characterized by different porosity values. The cooling trend was described both graphically and numerically, with the help of cooling curves and Cooling Rate Index. The latter, which proved strictly linked to porosity, was employed to find reliable equations for its indirect estimation. Simple and multiple regression analyses returned satisfactory outcomes, highlighting the great match between predicted and measured porosity values, thus confirming the goodness of the proposed model. This study brings a novelty in rock mechanics, laying the foundation for future researches aimed at refining achieved results for the validation of the model in a larger scale.

  1. Estimating metabolic heat loss in birds and mammals by combining infrared thermography with biophysical modelling.

    PubMed

    McCafferty, D J; Gilbert, C; Paterson, W; Pomeroy, P P; Thompson, D; Currie, J I; Ancel, A

    2011-03-01

    Infrared thermography (IRT) is a technique that determines surface temperature based on physical laws of radiative transfer. Thermal imaging cameras have been used since the 1960s to determine the surface temperature patterns of a wide range of birds and mammals and how species regulate their surface temperature in response to different environmental conditions. As a large proportion of metabolic energy is transferred from the body to the environment as heat, biophysical models have been formulated to determine metabolic heat loss. These models are based on heat transfer equations for radiation, convection, conduction and evaporation and therefore surface temperature recorded by IRT can be used to calculate heat loss from different body regions. This approach has successfully demonstrated that in birds and mammals heat loss is regulated from poorly insulated regions of the body which are seen to be thermal windows for the dissipation of body heat. Rather than absolute measurement of metabolic heat loss, IRT and biophysical models have been most useful in estimating the relative heat loss from different body regions. Further calibration studies will improve the accuracy of models but the strength of this approach is that it is a non-invasive method of measuring the relative energy cost of an animal in response to different environments, behaviours and physiological states. It is likely that the increasing availability and portability of thermal imaging systems will lead to many new insights into the thermal physiology of endotherms.

  2. Real-time quantification of viable bacteria in liquid medium using infrared thermography

    NASA Astrophysics Data System (ADS)

    Salaimeh, Ahmad A.; Campion, Jeffrey J.; Gharaibeh, Belal Y.; Evans, Martin E.; Saito, Kozo

    2011-11-01

    Quantifying viable bacteria in liquids is important in environmental, food processing, manufacturing, and medical applications. Since vegetative bacteria generate heat as a result of biochemical reactions associated with cellular functions, thermal sensing techniques, including infrared thermography (IRT), have been used to detect viable cells in biologic samples. We developed a novel method that extends the dynamic range and improves the sensitivity of bacterial quantification by IRT. The approach uses IRT video, thermodynamics laws, and heat transfer mechanisms to directly measure, in real-time, the amount of energy lost as heat from the surface of a liquid sample containing bacteria when the specimen cools to a lower temperature over 2 min. We show that the Energy Content ( EC) of liquid media containing as few as 120 colony-forming units (CFU) of Escherichia coli per ml was significantly higher than that of sterile media ( P < 0.0001), and that EC and viable counts were strongly positively correlated ( r = 0.986) over a range of 120 to approximately 5 × 10 8 CFU/ml. Our IRT approach is a unique non-contact method that provides real-time bacterial enumeration over a wide dynamic range without the need for sample concentration, modification, or destruction. The approach could be adapted to quantify other living cells in a liquid milieu and has the potential for automation and high throughput.

  3. Infrared thermography of transition due to isolated roughness elements in hypersonic flows

    NASA Astrophysics Data System (ADS)

    Avallone, F.; Schrijer, F. F. J.; Cardone, G.

    2016-02-01

    Boundary layer transition in high-speed flows is a phenomenon that despite extensive research over the years is still extremely hard to predict. The presence of protrusions or gaps can lead to an accelerated laminar-to-turbulent transition enhancing the thermal loads and the skin friction coefficient. In the current investigation, inverse heat transfer measurements using infrared thermography are performed on the flow past different roughness geometries in the form of cylinders and diamond at free stream Mach number equal to 7.5, h/δ ranging between 0.5 and 0.9 (where h is the roughness height and δ is the boundary layer thickness), and Reθ ranging between 1305 and 2450. The roughness elements are positioned on a 5° ramp placed at zero angle of attack. The measurements indicate that the roughness geometry influences the transitional pattern while the frontal area influences both the transition location and the maximum value of the Stanton number along the centreline. Moreover, there is a strong connection between the streamwise centreline Stanton number and the spreading of the wake width. In particular, the transition process is characterized by an approximately constant wake width. Differently, the wake width spreads at the location where the streamwise centreline Stanton number reaches the turbulent level. This point corresponds to a local maximum of the wake amplitude defined as one half of the maximum spanwise variation of the Stanton number.

  4. Automatic detection of diabetic foot complications with infrared thermography by asymmetric analysis.

    PubMed

    Liu, Chanjuan; van Netten, Jaap J; van Baal, Jeff G; Bus, Sicco A; van der Heijden, Ferdi

    2015-02-01

    Early identification of diabetic foot complications and their precursors is essential in preventing their devastating consequences, such as foot infection and amputation. Frequent, automatic risk assessment by an intelligent telemedicine system might be feasible and cost effective. Infrared thermography is a promising modality for such a system. The temperature differences between corresponding areas on contralateral feet are the clinically significant parameters. This asymmetric analysis is hindered by (1) foot segmentation errors, especially when the foot temperature and the ambient temperature are comparable, and by (2) different shapes and sizes between contralateral feet due to deformities or minor amputations. To circumvent the first problem, we used a color image and a thermal image acquired synchronously. Foot regions, detected in the color image, were rigidly registered to the thermal image. This resulted in 97.8% ± 1.1% sensitivity and 98.4% ± 0.5% specificity over 76 high-risk diabetic patients with manual annotation as a reference. Nonrigid landmark-based registration with B-splines solved the second problem. Corresponding points in the two feet could be found regardless of the shapes and sizes of the feet. With that, the temperature difference of the left and right feet could be obtained.

  5. Automatic detection of diabetic foot complications with infrared thermography by asymmetric analysis

    NASA Astrophysics Data System (ADS)

    Liu, Chanjuan; van Netten, Jaap J.; van Baal, Jeff G.; Bus, Sicco A.; van der Heijden, Ferdi

    2015-02-01

    Early identification of diabetic foot complications and their precursors is essential in preventing their devastating consequences, such as foot infection and amputation. Frequent, automatic risk assessment by an intelligent telemedicine system might be feasible and cost effective. Infrared thermography is a promising modality for such a system. The temperature differences between corresponding areas on contralateral feet are the clinically significant parameters. This asymmetric analysis is hindered by (1) foot segmentation errors, especially when the foot temperature and the ambient temperature are comparable, and by (2) different shapes and sizes between contralateral feet due to deformities or minor amputations. To circumvent the first problem, we used a color image and a thermal image acquired synchronously. Foot regions, detected in the color image, were rigidly registered to the thermal image. This resulted in 97.8%±1.1% sensitivity and 98.4%±0.5% specificity over 76 high-risk diabetic patients with manual annotation as a reference. Nonrigid landmark-based registration with B-splines solved the second problem. Corresponding points in the two feet could be found regardless of the shapes and sizes of the feet. With that, the temperature difference of the left and right feet could be obtained.

  6. Infra-red Thermography for High Throughput Field Phenotyping in Solanum tuberosum

    PubMed Central

    Prashar, Ankush; Yildiz, Jane; McNicol, James W.; Bryan, Glenn J.; Jones, Hamlyn G.

    2013-01-01

    The rapid development of genomic technology has made high throughput genotyping widely accessible but the associated high throughput phenotyping is now the major limiting factor in genetic analysis of traits. This paper evaluates the use of thermal imaging for the high throughput field phenotyping of Solanum tuberosum for differences in stomatal behaviour. A large multi-replicated trial of a potato mapping population was used to investigate the consistency in genotypic rankings across different trials and across measurements made at different times of day and on different days. The results confirmed a high degree of consistency between the genotypic rankings based on relative canopy temperature on different occasions. Genotype discrimination was enhanced both through normalising data by expressing genotype temperatures as differences from image means and through the enhanced replication obtained by using overlapping images. A Monte Carlo simulation approach was used to confirm the magnitude of genotypic differences that it is possible to discriminate. The results showed a clear negative association between canopy temperature and final tuber yield for this population, when grown under ample moisture supply. We have therefore established infrared thermography as an easy, rapid and non-destructive screening method for evaluating large population trials for genetic analysis. We also envisage this approach as having great potential for evaluating plant response to stress under field conditions. PMID:23762433

  7. Status and Plans for Infrared Thermography and Heat flux Measurements on NSTX-U

    NASA Astrophysics Data System (ADS)

    Gray, Travis; Ahn, Joon-Wook; Gan, Kaifu; McGann, Alistair; Reinke, Matthew; Maingi, Rajesh; Wirth, Brian

    2016-10-01

    Improvements and expansion of IR thermography tools on NSTX-U are being pursued to support a range of boundary physics research. Due to a carbon-lithium mixed material environment and upcoming use of high-Z materials, NSTX-U presents a challenge in determining the deposited power flux to plasma facing components (PFCs). The majority of the PFCs are graphite which has a high surface emissivity but extensive use of lithium wall conditioning creates a mixed material divertor environment. Furthermore, a row of low emissivity/highly reflective molybdenum tiles will be installed in the outboard divertor for the next run campaign. To overcome these challenges as well assess overall power balance in NSTX-U, infrared coverage of the PFCs has been increased. The lower divertor outer strike point (OSP) is observed by a 1.6 kHz IR camera equipped with dual-band optics to account for the changes in surface emissivity introduced with the addition of lithium [AG MCLean, RSI 2012]. A wide-angle view of the lower divertor and a tangential view of the HHFW antenna and limiters has been added for the commencement of plasma operations on the NSTX-U. Measurements of the lower divertor, inner strike point (ISP) as well as the upper diverter OSP will be implemented for the FY17 run campaign. The installation of the molybdenum tiles will also include calorimeters to further constrain the heat flux measurements on those tiles with plans to increase calorimeter coverage.

  8. Precise determination of the heat delivery during in vivo magnetic nanoparticle hyperthermia with infrared thermography.

    PubMed

    Rodrigues, Harley; Capistrano, Gustavo; Mello, Francyelli; Zufelato, Nicholas; Silveira-Lacerda, Elisangela; Bakuzis, Andris F

    2017-03-17

    Monitoring noninvasively and in real-time the heat delivery during magnetic nanoparticle hyperthermia is of fundamental importance to predict clinical outcome for cancer treatment. Infrared thermography (IRT) can inform the surface temperature due to three-dimensional heat delivery inside a subcutaneous tumor, an argument that is supported by numerical simulations. However, for precise temperature determination, it is of crucial relevance to use a correct experimental configuration. This work reports a magnetic nanoparticle hyperthermia study (MNH) using a sarcoma 180 murine tumor containing 3.9 mg of intratumorally injected manganese-ferrite nanoparticles. MNH was performed at low field amplitude and nonuniform field configuration. Five 30-minute in vivo magnetic hyperthermia experiments were performed, monitoring the surface temperature with fibre optical sensor and thermal camera at distinct angles with respect to the animal surface. The results indicate that temperature errors as huge as 7^{o}C can occur if the experiment is not properly designed. A new IRT error model is found to explain the data. More importantly, it is shown how to precisely monitor temperature with IRT during hyperthermia, which could positively impact heat dosimetry and clinical planning.

  9. Infrared thermography coupled with digital image correlation in studying plastic deformation on the mesoscale level

    NASA Astrophysics Data System (ADS)

    Wang, Xiaogang; Witz, Jean-François; El Bartali, Ahmed; Jiang, Chao

    2016-11-01

    This paper focuses on a study of plastic deformation on the mesoscale level by infrared thermography coupled with digital image correlation. First, a novel technique for fully-coupled thermal and kinematic measurements was developed, and the common problem of spatial coupling in the multifield measurement was solved successfully using an image registration method. Then the developed technique was applied to investigate the plastic deformation of a pure aluminium oligocrystal specimen in a tensile test. The deformed specimen manifested high strains of type out-of-plane, which were found closely associated with the crystallographic structure. From a metrological point of view, the out-of-plane effect on the thermographic measurement was analyzed, and the pertinent radiometric artifacts were estimated. The source of errors was verified through a correlation analysis between the estimated artifacts and specimen surface profile. Moreover, the out-of-plane effect on the kinematic measurement was investigated, and the relevant errors were analyzed via the correlation residual. The analysis highlighted the role of the microstructure that played in the plastic deformation and showed that grain boundary was crucial in shaping the heterogeneous deformation patterns for aluminium oligocrystals.

  10. A Quantitative Investigation of Surface Roughness Effects on Airfoil Boundary Layer Transition Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Beeby, Todd Daniel

    An investigation of the impact of subcritical leading edge distributed roughness elements on airfoil boundary layer transition location has been undertaken using infrared thermography. In particular, a quantitative approach to boundary layer transition location detection using a differential energy balance method was implemented using a heating pad to produce constant heat flux. This was performed on a S809 airfoil model at Re c = 0.75 and 1.0 x 106, using roughness elements of height k/c = 3.75, 4.25 and 5.00 x 10 --4, pattern densities of 2 to 10 %, and roughness locations of 1 to 6 % chord. Turbulator tape of height k/c = 6.67 x 10--4 was also examined. Results indicate significant impact on transition for all roughness cases, and a more pronounced influence of roughness density as compared to roughness element height. The phenomenon of early laminar bubble collapse was also found to occur for some roughness configurations. The quantitative method used was found to be an effective means for automated transition location determination.

  11. Reduction of evaporative flux in bean leaves due to chitosan treatment assessed by infrared thermography

    NASA Astrophysics Data System (ADS)

    Ludwig, N.; Cabrini, R.; Faoro, F.; Gargano, M.; Gomarasca, S.; Iriti, M.; Picchi, V.; Soave, C.

    2010-01-01

    Infrared thermography can be used as a tool for evaluating antitranspirant treatment through the measurement of evaporative fluxes. The aim of this work is to compare the leaf surface temperatures of plant treated with chitosan (CHT), a potential stomatal-closing antitranspirant, with temperatures of leaves treated with the commercially available antitranspirant Vapor Gard®, a film-forming polyterpene. The main problem in the correct evaluation of stomatal conductance at leaf level is due to the need of performing a measurement in a completely non-invasive method. The main advantage of thermographic method is the possibility to acquire information about instantaneous conditions of transpiration over a large number of plants, with no need of sampling and avoiding any contact with plants. Tests on bean plants ( Phaseolus vulgaris) showed the applicability of the thermal imaging to discriminate plants with different evaporation rate due to treatment with different antitranspirant compounds. Quantitative evaluation of evaporative flux and stomatal conductance was obtained through reference measurements on standards with calibrated conductance. Non-destructive gravimetric measurements were used in order to get a reliable evaluation of evaporative fluxes. In conclusion, thermographic approach, in climatic chamber, seems to be a valid tool for rapidly screening the performance of different antitranspirant products.

  12. Infrared thermography of evaporative fluxes and dynamics of salt deposition on heterogeneous porous surfaces

    NASA Astrophysics Data System (ADS)

    Nachshon, Uri; Shahraeeni, Ebrahim; Or, Dani; Dragila, Maria; Weisbrod, Noam

    2011-12-01

    Evaporation of saline solutions from porous media, common in arid areas, involves complex interactions between mass transport, energy exchange and phase transitions. We quantified evaporation of saline solutions from heterogeneous sand columns under constant hydraulic boundary conditions to focus on effects of salt precipitation on evaporation dynamics. Mass loss measurements and infrared thermography were used to quantify evaporation rates. The latter method enables quantification of spatial and temporal variability of salt precipitation to identify its dynamic effects on evaporation. Evaporation from columns filled with texturally-contrasting sand using different salt solutions revealed preferential salt precipitation within the fine textured domains. Salt precipitation reduced evaporation rates from the fine textured regions by nearly an order of magnitude. In contrast, low evaporation rates from coarse-textured regions (due to low capillary drive) exhibited less salt precipitation and consequently less evaporation rate suppression. Experiments provided insights into two new phenomena: (1) a distinct increase in evaporation rate at the onset of evaporation; and (2) a vapor pumping mechanism related to the presence of a salt crust over semidry media. Both phenomena are related to local vapor pressure gradients established between pore water and the surface salt crust. Comparison of two salts: NaCl and NaI, which tend to precipitate above the matrix surface and within matrix pores, respectively, shows a much stronger influence of NaCl on evaporation rate suppression. This disparity reflects the limited effect of NaI precipitation on matrix resistivity for solution and vapor flows.

  13. Classification of electrical problems detected by infrared thermography using a risk assessment process

    NASA Astrophysics Data System (ADS)

    McIntosh, Gregory B.; Huff, Roy

    2016-05-01

    For more than 40 years thermography has been used for electrical problem detection. In addition, since radiometric infrared cameras can establish apparent surface temperature of the problem, a classification system is often utilized based upon surface temperature, or temperature rise above normal operating temperature or ambient air temperature. This however can be an extremely unreliable classification method for a number of reasons including: emissivity and background energy; a lack of regard for failure modes and stressors; surface temperature variability with load and ambient conditions; temperature gradient from internal source to surface; and the presence of convection, just to name a few. Standards, such as NFPA 70B, try to address some of these issues by having very low threshold temperature limits, but this as well has issues including identifying an over-abundance of non-critical problems for immediate repair. This paper will present a risk assessment process and matrix which classifies electrical problems based upon a variety of factors affecting both probability and consequence of electrical component failure. Inherent in this process will be a discussion of understanding and analysing electrical connection failure modes and failure stressors, as well as consideration of both heat energy flow and stored energy rather than only considering surface temperature as a single point predictor of catastrophic failure.

  14. The use of high-resolution infrared thermography (HRIT) for the study of ice nucleation and ice propagation in plants.

    PubMed

    Wisniewski, Michael; Neuner, Gilbert; Gusta, Lawrence V

    2015-05-08

    Freezing events that occur when plants are actively growing can be a lethal event, particularly if the plant has no freezing tolerance. Such frost events often have devastating effects on agricultural production and can also play an important role in shaping community structure in natural populations of plants, especially in alpine, sub-arctic, and arctic ecosystems. Therefore, a better understanding of the freezing process in plants can play an important role in the development of methods of frost protection and understanding mechanisms of freeze avoidance. Here, we describe a protocol to visualize the freezing process in plants using high-resolution infrared thermography (HRIT). The use of this technology allows one to determine the primary sites of ice formation in plants, how ice propagates, and the presence of ice barriers. Furthermore, it allows one to examine the role of extrinsic and intrinsic nucleators in determining the temperature at which plants freeze and evaluate the ability of various compounds to either affect the freezing process or increase freezing tolerance. The use of HRIT allows one to visualize the many adaptations that have evolved in plants, which directly or indirectly impact the freezing process and ultimately enables plants to survive frost events.

  15. Diverging Drought Resistance of Scots Pine Provenances Revealed by Infrared Thermography.

    PubMed

    Seidel, Hannes; Schunk, Christian; Matiu, Michael; Menzel, Annette

    2016-01-01

    With recent climate changes, Scots pine (Pinus sylvestris L.) forests have been affected by die-off events. Assisted migration of adapted provenances mitigates drought impacts and promotes forest regeneration. Although suitable provenances are difficult to identify by traditional ecophysiological techniques, which are time consuming and invasive, plant water status can be easily assessed by infrared thermography. Thus, we examined the stress responses of 2-year-old potted Scots pine seedlings from six provenances (Bulgaria, France, Germany, Italy, Poland, and Spain) based on two thermal indices (crop water stress index and stomatal conductance index). Both indices were derived from infrared images during a 6-week drought/control treatment in a greenhouse in the summer of 2013. The pines were monitored during the stress and subsequent recovery period. After controlling for fluctuating environmental conditions, soil moisture or treatment-specific water supply was the most important driver of drought stress. The stress magnitude and response to soil water deficit depended on provenance. Under moderate drought conditions, pines from western and eastern Mediterranean provenances (Bulgaria, France, and Spain) expressed lower stress levels than those from both continental provenances (Germany and Poland). Moreover, pines from continental provenances were less resilient (showed less recovery after the stress period) than Mediterranean pines. Under extreme drought, all provenances were equally stressed with almost no significant differences in their thermal indices. Provenance-specific differences in drought resistance, which are associated with factors such as summer precipitation at the origin of Scots pine seedlings, may offer promising tracks of adaptation to future drought risks.

  16. Involuntary motion tracking for medical dynamic infrared thermography using a template-based algorithm

    PubMed Central

    Herman, Cila

    2013-01-01

    In medical applications, Dynamic Infrared (IR) Thermography is used to detect the temporal variation of the skin temperature. Dynamic Infrared Imaging first introduces a thermal challenge such as cooling on the human skin, and then a sequence of hundreds of consecutive frames is acquired after the removal of the thermal challenge. As a result, by analyzing the temporal variation of the skin temperature over the image sequence, the thermal signature of skin abnormality can be examined. However, during the acquisition of dynamic IR imaging, the involuntary movements of patients are unavoidable, and such movements will undermine the accuracy of diagnosis. In this study, based on the template-based algorithm, a tracking approach is proposed to compensate the motion artifact. The affine warping model is adopted to estimate the motion parameter of the image template, and then the Lucas-Kanade algorithm is applied to search for the optimized parameters of the warping function. In addition, the weighting mask is also incorporated in the computation to ensure the robustness of the algorithm. To evaluate the performance of the approach, two sets of IR image sequences of a subject’s hand are analyzed: the steady-state image sequence, in which the skin temperature is in equilibrium with the environment, and the thermal recovery image sequence, which is acquired after cooling is applied on the skin for 60 seconds. By selecting the target region in the first frame as the template, satisfactory tracking results were obtained in both experimental trials, and the robustness of the approach can be effectively ensured in the recovery trial. PMID:24392205

  17. Detection and Characterization of Package Defects and Integrity Failure using Dynamic Scanning Infrared Thermography (DSIRT).

    PubMed

    Morris, Scott A

    2016-02-01

    A dynamic scanning infrared thermography (DSIRT) system developed at the Univ. of Illinois Urbana-Champaign (UIUC) Packaging Lab relies on variation in transient thermal artifacts to indicate defects, and offers the possibility of characterization of many types of materials and structures. These include newer polymer and laminate-based structures for shelf-stable foods that lack a reliable, nondestructive method for inspection, which is a continuing safety issue. Preliminary trials were conducted on a polyester/aluminum foil/polypropylene retort pouch laminate containing artificially-induced failed seal and insulating inclusion defects ranging from 1 to 10 mm wide in the plane of the seal. The samples were placed in relative motion to a laterally positioned infrared laser, inducing heating through the plane of the seal. The emergent thermal artifact on the obverse side was sensed using either a bolometer camera or a thermopile sensor, with thermal anomalies indicating potential defects and the results of each sensors were compared. The bolometer camera detected defects to the limit of its measured optical resolution-approximately 1 mm at 20 cm-although the lower-resolution thermopile sensors were only capable of detecting 5 mm defects even at closer distances of approximately 5 mm. In addition, a supplementary magnification system was fitted to the bolometer camera which increased resolution but reduced field of view and would require a much higher frame rate to be useful. Automatic processing of the image data rapidly detected the model defects and can lead to development of an automated inspection system.  Much higher material throughput speeds are feasible using faster instruments, and the system is scalable.

  18. Infrared thermography non-destructive evaluation of lithium-ion battery

    NASA Astrophysics Data System (ADS)

    Wang, Zi-jun; Li, Zhi-qiang; Liu, Qiang

    2011-08-01

    The power lithium-ion battery with its high specific energy, high theoretical capacity and good cycle-life is a prime candidate as a power source for electric vehicles (EVs) and hybrid electric vehicles (HEVs). Safety is especially important for large-scale lithium-ion batteries, especially the thermal analysis is essential for their development and design. Thermal modeling is an effective way to understand the thermal behavior of the lithium-ion battery during charging and discharging. With the charging and discharging, the internal heat generation of the lithium-ion battery becomes large, and the temperature rises leading to an uneven temperature distribution induces partial degradation. Infrared (IR) Non-destructive Evaluation (NDE) has been well developed for decades years in materials, structures, and aircraft. Most thermographic methods need thermal excitation to the measurement structures. In NDE of battery, the thermal excitation is the heat generated from carbon and cobalt electrodes in electrolyte. A technique named "power function" has been developed to determine the heat by chemical reactions. In this paper, the simulations of the transient response of the temperature distribution in the lithium-ion battery are developed. The key to resolving the security problem lies in the thermal controlling, including the heat generation and the internal and external heat transfer. Therefore, three-dimensional modelling for capturing geometrical thermal effects on battery thermal abuse behaviour is required. The simulation model contains the heat generation during electrolyte decomposition and electrical resistance component. Oven tests are simulated by three-dimensional model and the discharge test preformed by test system. Infrared thermography of discharge is recorded in order to analyze the security of the lithium-ion power battery. Nondestructive detection is performed for thermal abuse analysis and discharge analysis.

  19. Diverging Drought Resistance of Scots Pine Provenances Revealed by Infrared Thermography

    PubMed Central

    Seidel, Hannes; Schunk, Christian; Matiu, Michael; Menzel, Annette

    2016-01-01

    With recent climate changes, Scots pine (Pinus sylvestris L.) forests have been affected by die-off events. Assisted migration of adapted provenances mitigates drought impacts and promotes forest regeneration. Although suitable provenances are difficult to identify by traditional ecophysiological techniques, which are time consuming and invasive, plant water status can be easily assessed by infrared thermography. Thus, we examined the stress responses of 2-year-old potted Scots pine seedlings from six provenances (Bulgaria, France, Germany, Italy, Poland, and Spain) based on two thermal indices (crop water stress index and stomatal conductance index). Both indices were derived from infrared images during a 6-week drought/control treatment in a greenhouse in the summer of 2013. The pines were monitored during the stress and subsequent recovery period. After controlling for fluctuating environmental conditions, soil moisture or treatment-specific water supply was the most important driver of drought stress. The stress magnitude and response to soil water deficit depended on provenance. Under moderate drought conditions, pines from western and eastern Mediterranean provenances (Bulgaria, France, and Spain) expressed lower stress levels than those from both continental provenances (Germany and Poland). Moreover, pines from continental provenances were less resilient (showed less recovery after the stress period) than Mediterranean pines. Under extreme drought, all provenances were equally stressed with almost no significant differences in their thermal indices. Provenance-specific differences in drought resistance, which are associated with factors such as summer precipitation at the origin of Scots pine seedlings, may offer promising tracks of adaptation to future drought risks. PMID:27630643

  20. Assessing feed efficiency in beef steers through feeding behavior, infrared thermography and glucocorticoids.

    PubMed

    Montanholi, Y R; Swanson, K C; Palme, R; Schenkel, F S; McBride, B W; Lu, D; Miller, S P

    2010-05-01

    A better understanding of the factors regulating feed efficiency and their potential as predictors of feed efficiency in cattle is needed. Therefore, the potential of three classes of traits, namely, feeding behavior characteristics: daily time at feeder (TF; min/day), time per meal (TM; min), meal size (MS; g DM), eating rate (ER; g DM/min), number of daily meals (NM) and daily visits to the feeder (VF); infrared (IR) thermography traits (°C): eye (EY), cheek (CK), snout (SN), ribs (RB) and hind area (HA); and glucocorticoid levels: fecal cortisol metabolites (FCM; ng/g) and plasma cortisol (PC; ng/ml) as predictors of efficiency were evaluated in 91 steers (436 ± 37 kg) over 2 years (Y1 = 46; Y2 = 45). Additionally, the individual traits of each of these three classes were combined to define three single traits. Individual daily feed intake of a corn silage and high-moisture corn-based diet was measured using an automated feeding system. Body weight and thermographs were taken every 28 days over a period of 140 days. Four productive performance traits were calculated: daily dry matter intake (DMI), average daily gain (ADG), feed to gain ratio (F : G) and residual feed intake (RFI). Steers were also classified into three RFI categories (low-, medium- and high-RFI). Among the feeding behavior characteristics, MS and ER were correlated with all efficiency traits (range: 0.26 to 0.75). Low-RFI (more efficient steers) had smaller MS, lower ER and fewer VF in comparison to high-RFI steers. Less efficient steers (high-RFI) performed more VF during the nocturnal period than more efficient steers. More efficient steers had lower CK and SN temperatures than less efficient steers (28.1°C v. 29.2°C and 30.0°C v. 31.2°C), indicating greater energetic efficiency for low-RFI steers. In terms of glucocorticoids, PC was not correlated with efficiency traits. In contrast, more efficient steers had higher FCM in comparison to less efficient steers (51.1 v. 31.2 ng

  1. Comparative study on submillimeter flaws in stitched T-joint carbon fiber reinforced polymer by infrared thermography, microcomputed tomography, ultrasonic c-scan and microscopic inspection

    NASA Astrophysics Data System (ADS)

    Zhang, Hai; Hassler, Ulf; Genest, Marc; Fernandes, Henrique; Robitaille, Francois; Ibarra-Castanedo, Clemente; Joncas, Simon; Maldague, Xavier

    2015-10-01

    Stitching is used to reduce dry-core (incomplete infusion of T-joint core) and reinforce T-joint structure. However, it may cause new types of flaws, especially submillimeter flaws. Microscopic inspection, ultrasonic c-scan, pulsed thermography, vibrothermography, and laser spot thermography are used to investigate the internal flaws in a stitched T-joint carbon fiber-reinforced polymer (CFRP) matrix composites. Then, a new microlaser line thermography is proposed. Microcomputed tomography (microCT) is used to validate the infrared results. A comparison between microlaser line thermography and microCT is performed. It was concluded that microlaser line thermography can detect the internal submillimeter defects. However, the depth and size of the defects can affect the detection results. The microporosities with a diameter of less than 54 μm are not detected in the microlaser line thermography results. Microlaser line thermography can detect the microporosity (a diameter of 0.162 mm) from a depth of 90 μm. However, it cannot detect the internal microporosity (a diameter of 0.216 mm) from a depth of 0.18 mm. The potential causes are given. Finally, a comparative study is conducted.

  2. Development of an interatmospheric window wavelength (5-9 μm) infrared thermography with an advanced image processing technique

    NASA Astrophysics Data System (ADS)

    Sato, Daisuke; Komiyama, Tatsuhito; Sakagami, Takahide; Kubo, Shiro

    2006-04-01

    Recently, deterioration of concrete structures before their design life has become a serious social problem in Japan. Nondestructive inspection techniques are required, for detecting defects and damages in concrete structures, such as subsurface void or delamination. As one of these techniques, the thermographic NDT can be applied as an effective NDT technique to inspect large area of the objective structure from distant place. In addition, it does not require any chemicals and application of physical excitation for inspection. However, the thermographic NDT has a shortcoming that the measurement results are affected by the reflection of atmospheric radiation due to the sunlight, sky or surrounding materials. Since most of the buildings in Japan are covered with luster materials with low emissivity, such as tile or mortal, infrared reflection on the surface is difficult to be neglected. To reduce the influence of these reflection noises, the infrared thermography with detectable wavelength from 5 to 8 μm, which coincides with absorption range of moisture, is utilized. In this research, a new infrared thermography with 5 to 8 μm wavelength range by applying a band pass filter and an uncooled microbolometer infrared array detector. Further, a new signal to noise (S/N) ratio improvement technique has been developed in order to compensate a deterioration of sensitivity due to the band pass filter.

  3. FPA-based infrared thermography as applied to the study of cutaneous perspiration and stimulated vascular response in humans.

    PubMed

    Vainer, Boris G

    2005-12-07

    This review gives an overview of focal plane array (FPA)-based infrared (IR) thermography as a powerful research method in the field of physiology and medicine. Comparison of the gained results with the data previously obtained by other authors with other research tools is given. Outer thermoregulatory manifestations displayed by the human organism subjected to whole-body heating (sauna bath) and physical loads (exercise bicycling) are quantitatively analysed. Some details of human body emotional sweating (psycho-physiological effect) are reported. Particular attention is paid to studying active sweat glands as individual objects. All experimental data were obtained with the help of a high-sensitivity (0.03 degrees C) fast 128 x 128 InAs IR detector-based thermal imaging system operating in the short-wave spectral region (2.5 to 3 microm) and perfectly suiting medical purposes. It is shown that IR thermography makes it possible to overcome limitations inherent to contact measuring means that were traditionally used before in thermal studies. It is also shown that heterogeneous thermograms displayed by organisms with disturbed inner equilibrium can be quantitatively analysed in terms of statistical parameters of related surface-temperature histograms, such as the mean temperature and the standard deviation of temperature (SDT). The increase and the decrease in SDT turned out to be typical of prolonged physical load and subsequent relaxation, and of external whole-body heating, respectively. Explanation of this result based on a hypothesis advanced within the context of the doctrine of human-organism evolution is given. Skin-temperature distribution function accompanying the relaxed organism in normality was found to closely resemble normal-distribution function. Symmetry break down and variation of the shape of this characteristic may serve as an indicator of homeostasis shift and can be used as a quantitative criterion for the latter. A new phenomenon, stable

  4. Non-destructive inspection of drilled holes in reinforced honeycomb sandwich panels using active thermography

    NASA Astrophysics Data System (ADS)

    Usamentiaga, R.; Venegas, P.; Guerediaga, J.; Vega, L.; López, I.

    2012-11-01

    The aerospace industry is in constant need of ever-more efficient inspection methods for quality control. Product inspection is also essential to maintain the safe operation of aircraft components designed to perform for decades. This paper proposes a method for non-destructive inspection of drilled holes in reinforced honeycomb sandwich panels. Honeycomb sandwich panels are extensively employed in the aerospace industry due to their high strength and stiffness to weight ratios. In order to attach additional structures to them, panels are reinforced by filling honeycomb cells and drilling holes into the reinforced areas. The proposed procedure is designed to detect the position of the holes within the reinforced area and to provide a robust measurement of the distance between each hole and the boundary of the reinforced area. The result is a fast, safe and clean inspection method for drilled holes in reinforced honeycomb sandwich panels that can be used to robustly assess a possible displacement of the hole from the center of the reinforced area, which could have serious consequences. The proposed method is based on active infrared thermography, and uses state of the art methods for infrared image processing, including signal-to-nose ratio enhancement, hole detection and segmentation. Tests and comparison with X-ray inspections indicate that the proposed system meets production needs.

  5. Nondestructive testing of plastered mosaics with the use of active thermography approaches

    NASA Astrophysics Data System (ADS)

    Cheilakou, Eleni; Avdelidis, Nico P.; Ibarra-Castanedo, Clemente; Koui, Maria; Bendada, Abdel Hakim; Maldague, Xavier P.

    2010-05-01

    In this work, different mosaics covered with various plasters (of thickness and compositions) were evaluated in lab by means of active long wave and mid wave thermography approaches, with the intention of detecting the tesserae beneath the plastered surface. Thermal images as well as thermal contrast curves between plastered surfaces and plastered mosaics were recorded. Special considerations concerning the applicability and accuracy of the used approaches for this specific application are presented. Results from the assessment are presented and discussed, indicating that images seeing through the mortar-plaster on plastered mosaic surfaces can be obtained using active thermography approaches.

  6. Infrared thermography as option for evaluating the treatment effect of percutaneous transluminal angioplasty by patients with peripheral arterial disease.

    PubMed

    Staffa, Erik; Bernard, Vladan; Kubicek, Lubos; Vlachovsky, Robert; Vlk, Daniel; Mornstein, Vojtech; Bourek, Ales; Staffa, Robert

    2017-02-01

    Aim of this study was to evaluate the possible use of infrared thermography as a supplementary method to the ankle-brachial index used in assessing the treatment effect of percutaneous transluminal angioplasty. The study included 21 patients, mean age was 60.22 years. Healthy control group included 20 persons, mean age was 55.60 years. Patients with symptomatic peripheral arterial disease (Fontaine stages I-III) were admitted for endovascular treatment by percutaneous transluminal angioplasty. Thermal images and ankle-brachial index values were obtained before and after treatment by percutaneous transluminal angioplasty. Median temperature change in the treated limb was 0.4℃, for non-treated limb was -0.5℃. The median value of ankle-brachial index in the treated limb increased by 0.17 from 0.81 after the procedure. The median value of ankle-brachial index in the non-treated limb decreased by 0.03 from the value of 1.01. Significant difference between treated limb and non-treated limb in change of ankle-brachial index was found with p value = .0035. The surface temperature obtained by the infrared thermography correlates with ankle-brachial index. We present data showing that the increase of ankle-brachial index is associated with increase of skin temperature in the case of limbs treated by percutaneous transluminal angioplasty. Our results also suggest potential of the use of infrared thermography for monitoring foot temperature as a means of early detection of onset of foot ischemic disorders.

  7. Integration of infrared thermography and high-frequency electromagnetic methods in archaeological surveys

    NASA Astrophysics Data System (ADS)

    di Maio, Rosa; Meola, Carosena; Fedi, Maurizio; Carlomagno, Giovanni Maria

    2010-05-01

    An integration of high-resolution non-destructive techniques is presented for the inspection and evaluation of ancient architectonic structures. Infrared thermography (IRT) represents a valuable tool for nondestructive evaluation of architectonic structures and artworks because it is capable of giving indications about most of the degradation sources of artworks and buildings of both historical interest and civil use. In particular, it is possible to detect cracks, disbondings, alteration of material consistency, etc. Indeed, by choosing the most adequate thermographic technique, it is possible to monitor the conservation state of artworks in time and to detect the presence of many types of defects (e.g., voids, cracks, disbondings, etc.) in different types of materials (e.g., concrete, masonry structures, bronze, etc.). The main advantages of infrared thermography when dealing with precious artworks may be summarized with three words: non-contact, non-invasive, and two-dimensionality. It is possible to inspect either a large surface such as the facade of a palace, or a very small surface of only few square millimetres. Conversely, the inspection depth is quite small; generally, of the order of centimetres. However, as demonstrated in previous work, IRT well matches with electric-and electromagnetic-type geophysical methods to characterize the overlapping zone from low-to-high depth in masonry structures. In particular, the use of high-frequency electromagnetic techniques, such as the ground penetrating radar (GPR), permits to reach investigation depths of some ten of centimetres by choosing appropriate frequencies of the transmitted electromagnetic signal. In the last decade a large utilisation of the GPR methodology to non-destructive analysis of engineering and architectural materials and structures has been experienced. This includes diverse features, such as definition of layer thickness, characterisation of different constructive materials, identification of

  8. Long Hole Film Cooling Dataset for CFD Development . Part 1; Infrared Thermography and Thermocouple Surveys

    NASA Technical Reports Server (NTRS)

    Shyam, Vikram; Thurman, Douglas; Poinsatte, Phillip; Ameri, Ali; Eichele, Peter; Knight, James

    2013-01-01

    An experiment investigating flow and heat transfer of long (length to diameter ratio of 18) cylindrical film cooling holes has been completed. In this paper, the thermal field in the flow and on the surface of the film cooled flat plate is presented for nominal freestream turbulence intensities of 1.5 and 8 percent. The holes are inclined at 30deg above the downstream direction, injecting chilled air of density ratio 1.0 onto the surface of a flat plate. The diameter of the hole is 0.75 in. (0.01905 m) with center to center spacing (pitch) of 3 hole diameters. Coolant was injected into the mainstream flow at nominal blowing ratios of 0.5, 1.0, 1.5, and 2.0. The Reynolds number of the freestream was approximately 11,000 based on hole diameter. Thermocouple surveys were used to characterize the thermal field. Infrared thermography was used to determine the adiabatic film effectiveness on the plate. Hotwire anemometry was used to provide flowfield physics and turbulence measurements. The results are compared to existing data in the literature. The aim of this work is to produce a benchmark dataset for Computational Fluid Dynamics (CFD) development to eliminate the effects of hole length to diameter ratio and to improve resolution in the near-hole region. In this report, a Time-Filtered Navier Stokes (TFNS), also known as Partially Resolved Navier Stokes (PRNS), method that was implemented in the Glenn-HT code is used to model coolant-mainstream interaction. This method is a high fidelity unsteady method that aims to represent large scale flow features and mixing more accurately.

  9. Use of infrared thermography to assess the influence of high environmental temperature on rabbits.

    PubMed

    de Lima, V; Piles, M; Rafel, O; López-Béjar, M; Ramón, J; Velarde, A; Dalmau, A

    2013-10-01

    The aim of this work was to ascertain if infrared thermography (IRT) can be used on rabbits to assess differences in surface body temperature when they are subjected to two different environmental temperatures outside the comfort zone. Rabbits housed in room A were maintained at a temperature of below 30°C and rabbits in room B at a temperature of above 32°C for a year. Faeces were collected six times during the year to assess stress by means of faecal cortisol metabolites (FCM). The assessment of IRT was carried out to assess maximum and minimum temperatures on the eyes, nose and ears. FCM concentration was higher in room B than A, to confirm that stress conditions were higher in room B. Significant differences in IRT were found between the animals housed in both rooms. It was observed that it was more difficult for animals from room B to maintain a regular heat loss. Although all the body zones used to assess temperature with IRT gave statistical differences, the correlations found between the eyes, nose and ears were moderate, suggesting that they were giving different information. In addition, differences up to 3.36°C were found in the eye temperature of rabbits housed in the same room, with a clear effect of their position in relation to extractors and heating equipments. Therefore, IRT could be a good tool to assess heat stress in animals housed on typical rabbit farm buildings, giving a measure of how the animal is perceiving a combination of humidity, temperature and ventilation. Some face areas were better for analysing images. Minimum temperature on eyes and temperatures on nose are suggested to assess heat losses and critical areas of the farm for heat stress in rabbits.

  10. Breast reconstruction with absorbable mesh sling: dynamic infrared thermography of skin envelope

    PubMed Central

    Hashimoto, Yoko; Yuasa, Takeshi; Suzuki, Yoshinori; Saisho, Hiroshi

    2017-01-01

    Background To immediate reconstruct ptosis breasts, we used polyglactin (Vicryl; Ethicon Inc., Somerville, NJ, USA) mesh as an inferolateral sling. However, Vicryl mesh is absorbable and losing function as a supporting structure. We doubt about the stability of the blood supply to the inferior part of the flap when it is in direct contact with inner implant. In this study, we examine the complications and the safety of the skin flap of this absorbable mesh sling (AMS) procedure. Methods The outcomes of 80 cases were examined, and the 1-year safety record of 40 cases was assessed. Complications were divided into minor complications, major complications requiring surgical intervention, and major complications requiring the reconstructive surgery to be halted. In addition, we examined the blood perfusion of the skin flap by dynamic infrared thermography (DIRT). Results Among 80 patients with AMS procedure, 73 breasts were reconstructed immediately and in one-stage. Complication outcomes are presented; there were 4 cases of minor flap necrosis (5%) and 4 of major complications resulting in surgical correction (5%). One patient required additional surgery, and the implant was moved into the musculocutaneous flap (1.3%). In 40 patients 1 year after surgery, DIRT showed significant decreased of blood perfusion in the ipsilateral inferior sites in comparison with the superior sites. Conclusions Blood perfusion was comparably insufficient in the inferior area of the reconstructed breast mound with AMS, where the pectoralis muscle could not be used to line the inside of the envelope. However, there were no severe flap complications due to ischemia. PMID:28210555

  11. Repeatability of Infrared Plantar Thermography in Diabetes Patients: A Pilot Study

    PubMed Central

    Balbinot, Luciane Fachin; Robinson, Caroline Cabral; Achaval, Matilde; Zaro, Milton Antônio; Brioschi, Marcos Leal

    2013-01-01

    Objective Infrared (IR) thermography has been used as a complementary diagnostic method in several pathologies, including distal diabetic neuropathy, by tests that induce thermoregulatory responses, but nothing is known about the repeatability of these tests. This study aimed to assess the repeatability of the rewarming index in subjects with type 2 diabetes mellitus (T2DM) and nondiabetic control subjects. Methods Using an IR camera, plantar IR images were collected at baseline (pre-) and 10 min after (post-) cold stress testing on two different days with 7 days interval. Plantar absolute average temperatures pre- and post-cold stress testing, the difference between them (ΔT), and the rewarming index were obtained and compared between days. Repeatability of the rewarming index after the cold stress test was assessed by Bland–Altman plot limits of agreement. Results Ten T2DM subjects and ten nondiabetic subjects had both feet analyzed. Mean age did not differ between groups (p = .080). Absolute average temperatures of plantar region pre- (p = .033) and post-cold stress test (p = .019) differed between days in nondiabetic subjects, whereas they did not differ in T2DM subjects (pretest, p = .329; post-test, p = .540). ΔT and rewarming index did not differ between days for both groups, and the rewarming index presented a 100% agreement of day-to-day measurements from T2DM subjects and 95% with nondiabetic subjects. Conclusions The rewarming index after cold stress testing presented good repeatability between two days a week in both groups. Despite T2DM subjects presenting no differences on absolute temperature values between days, ΔT or rewarming index after cold stress testing remain recommended beside absolute temperature values for clinical use. PMID:24124938

  12. Effect of routine claw trimming on claw temperature in dairy cows measured by infrared thermography.

    PubMed

    Alsaaod, M; Syring, C; Luternauer, M; Doherr, M G; Steiner, A

    2015-04-01

    Infrared thermography (IRT) was used to assess the effect of routine claw trimming on claw temperature. In total, 648 IRT observations each were collected from 81 cows housed in 6 tiestalls before and 3 wk after claw trimming. The feet were classified as either healthy (nonlesion group, n = 182) or affected with infectious foot disorders (group IFD, n = 142). The maximal surface temperatures of the coronary band and skin and the difference of the maximal temperatures (ΔT) between the lateral and medial claws of the respective foot were assessed. Linear mixed models, correcting for the hierarchical structure of the data, ambient temperature, and infectious status of the claws, were developed to evaluate the effect of time in relation to the trimming event (d 0 versus d 21) and claw (medial versus lateral). Front feet and hind feet were analyzed separately. Ambient temperature and infectious foot status were identified as external and internal factors, respectively, that significantly affected claw temperature. Before claw trimming, the lateral claws of the hind feet were significantly warmer compared with the medial claws, whereas such a difference was not evident for the claws of the front feet. At d 21, ΔT of the hind feet was reduced by ≥ 0.25 °C, whereas it was increased by ≤ 0.13 °C in the front feet compared with d 0. Therefore, trimming was associated with a remarkable decrease of ΔT of the hind claws. Equalizing the weight bearing of the hind feet by routine claw trimming is associated with a measurable reduction of ΔT between the paired hind claws.

  13. Use of infrared thermography to assess laying-hen feather coverage.

    PubMed

    Zhao, Y; Xin, H; Dong, B

    2013-02-01

    Infrared thermography (IRT) was compared with the traditional 4-scale feather scoring (FS, with 1 representing the worst feather coverage and 4 the best) method for assessing feather coverage of laying hens. The feather coverage of 6 body parts (head, dorsal neck, front neck and crop, back, breast, and belly), body surface temperature distribution, and relative change in sensible heat loss of 60 laying hens (Lohmann SL white breed) at 28, 56, or 73 wk of age (20 hens per age group) were compared by using IRT. For all the 6 body parts and the area-weighted overall, the area of excellent feather (EF) determined by IRT was positively correlated with the 4-scale scores determined by FS (P < 0.05), whereas the areas of fair feather (FF), no feather (NF), and body surface temperature were negatively correlated with FS scores (P < 0.05). Feather deterioration occurred for elder hens at all body parts. Feather coverage of the hens was classified as 98.7% EF, 1.3% FF, and 0% NF at 28 wk of age; 70.2% EF, 20.6% FF, and 9.2% NF at 56 wk of age; and 35.4% EF, 17.1% FF, and 49.5% NF at 73 wk of age. As a result of less feather coverage and higher surface temperature, sensible heat loss was speculated to be higher for 56- and 73-wk-old hens than for 28-wk-old hens, potentially leading to higher feed-to-egg conversion for the elder hens. It was concluded that IRT is a promising technique or tool that may provide a more objective and quantitative evaluation of laying-hen feather conditions and delineation of bird thermoregulation.

  14. Infrared Flash Thermography Applied to the External Defect Detection on Htr Fuel Particles during the Manufacturing Process

    NASA Astrophysics Data System (ADS)

    Hermosilla-Lara, S.; Piriou, M.; Levesque, P.

    2008-02-01

    The authors propose the use of an adapted flash thermography method to perform the online detection of open cracks on high temperature reactor (HTR) fuel. The method consists, via an infrared camera, in the measurement of the particle temperature increase produced by a heating pulse on the particle external surface. Study is performed on laser notches and real cracks located in the different particle layers. It includes the influence of the defect relative position with respect to the heating source, as well as the influence of operating conditions. It is shown that this technique is able to yield good discrimination between sound and flawed particles at a rate that meets production constraints.

  15. Infrared thermography analysis of thermal diffusion induced by RF magnetic field on agar phantoms loaded with magnetic nanoparticles

    NASA Astrophysics Data System (ADS)

    Bante-Guerra, Jose; Macías, J. D.; Caballero-Aguilar, L.; Vales-Pinzón, C.; Alvarado-Gil, J. J.

    2013-02-01

    Recently, several treatments for fighting malignant tumors have been designed. However these procedures have well known inconveniences, depending on their applicability, tumor size and side effects, among others. Magnetic hyperthermia is a safe, non-invasive method for cancer therapy. This treatment is applied via elevation of target tissue temperature by dissipation of heat from Magnetic Nanoparticles (MNPs), previously located within the tumor. The induction of heat causes cell death and therefore the removal of the tumor. In this work the thermal diffusion in phantoms of agar loaded with magnetic nanoparticles (MNPs) is studied using the infrared thermography technique, which is widely used in biology/medicine (e.g. skin temperature mapping). Agar is one of the materials used to simulate different types of body tissues, these samples are known as "phantoms". Agar is of natural origin, low cost and high degree of biocompatibility. In this work the agar gel was embedded with MNPs by coprecipitation and placed in an alternating magnetic field radiation. As a consequence, the energy from the radiation source is dissipated as heat and then transferred from the MNP to the gel, increasing its temperature. For the temperature analysis, the samples of agar gel were stimulated by RF magnetic field generated by coils. Heating was measured with infrared thermography using a Thermovision A20M infrared camera. Thermographic images allowed obtaining the dependence of thermal diffusion in the phantom as a function of the magnitude of the applied RF magnetic field and the load of magnetic particles.

  16. Use of infra-red thermography for automotive climate control analysis

    SciTech Connect

    Burch, S.D.; Hassani, V.; Penney, T.R.

    1994-03-01

    In this paper, several automotive climate control applications for IR thermography are described. Some of these applications can be performed using conventional IR techniques. Others, such as visualizing the air temperature distribution within the cabin, at duct exits, and at heater and evaporator faces, require new experimental methods. In order to capture the temperature distribution within an airstream, a 0.25-mm-thick (0.01 inch) fiberglass screen is used. This screen can be positioned perpendicular or parallel to the flow to obtain three-dimensional spatial measurements. In many cases, the air flow pattern can be inferred from the resulting temperature distribution, allowing improved air distribution designs. In all cases, significant improvement in the speed, ease, and quantity of temperature distribution information can be realized with thermography as compared to conventional thermocouple array techniques. Comparisons are presented between IR thermography images and both thermocouple measurements and computational fluid dynamics (CFD) predictions.

  17. Infrared thermography based studies on the effect of age on localized cold stress induced thermoregulation in human

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Bagavathiappan, S.; Nishanthi, K.; Mohanalakshmi, K.; Veni, L.; Saumya; Yacin, S. M.; Philip, John

    2016-05-01

    Thermoregulatory control of blood flow plays an important role in maintaining the human body temperature and it provides physiological resistance against extreme environmental thermal stresses. To understand the role of age on thermal signals from veins and the thermoregulatory mechanism, the dynamic variation of the vein temperature on the hands of 17 human subjects, under a localized cold stress, was studied using infrared thermography. It was observed that the vein temperature of the stimulated hand initially decreased with time up to a time interval (called 'inversion time'), which was attributed to the localized cutaneous vasoconstriction. Beyond inversion time, a rise in the vein temperature of the stimulated hand was observed. A shift in the inversion time to higher values was observed for the older subjects, which was attributed to the reduced efficiency and responsiveness of the cutaneous vasoconstriction mechanism in these subjects. Our studies indicated that the inversion time increased linearly with subject age with strong positive Pearson's correlation coefficient of 0.94. It was also observed that the contralateral symmetry in vasoconstriction was much lower in older subjects than the younger subjects. The absolute difference between the left and right inversion time varied between 11-118 s and 5-28 s for the older and younger subjects, respectively. Our study clearly demonstrated that infrared thermography is one of the most effective experimental tool for studying dynamic variation in vein pixel temperature under localized thermal stresses.

  18. Magnetic hyperthermia study in water based magnetic fluids containing TMAOH coated Fe3O4 using infrared thermography

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Ranoo, Surojit; Philip, John

    2017-01-01

    We study the alternating magnetic field induced heating of a water based ferrofluid containing tetramethyl ammonium hydroxide coated iron oxide nanoparticles using infrared thermography and compare the results obtained from the conventional fiber optic temperature sensor. Experiments are performed on ferrofluid samples of five different concentrations and under four different external field amplitudes at a fixed frequency. The temperature rise curves measured using both the infrared thermography and fiber optic sensor are found to be very similar up to a certain time interval, above which deviations are observed, which are attributed to the internal and external convection phenomena. A correction methodology is developed to account for the convection losses. The convection corrected specific absorption rate is found to be in good agreement with the values obtained from the conventional fiber optic temperature sensor, within a maximum error of ±3.4%. The highest specific absorption rate obtained in the present study is 135.98 (±4.6) W/gFe for a sample concentration of 3 wt.%, at an external field amplitude and a frequency of 63.0 kA m-1 and 126 kHz, respectively. The specific absorption rate is found to decrease with increasing sample concentration, due to the enhancement of dipolar interaction with increasing sample concentration due to agglomeration. This study validates the efficacy and universal applicability of IRT as an alternate, real time, non-contact and wide area temperature measurement methodology for magnetic fluid hyperthermia experiments without any sample contamination.

  19. Detection of micro solder balls using active thermography and probabilistic neural network

    NASA Astrophysics Data System (ADS)

    He, Zhenzhi; Wei, Li; Shao, Minghui; Lu, Xingning

    2017-03-01

    Micro solder ball/bump has been widely used in electronic packaging. It has been challenging to inspect these structures as the solder balls/bumps are often embedded between the component and substrates, especially in flip-chip packaging. In this paper, a detection method for micro solder ball/bump based on the active thermography and the probabilistic neural network is investigated. A VH680 infrared imager is used to capture the thermal image of the test vehicle, SFA10 packages. The temperature curves are processed using moving average technique to remove the peak noise. And the principal component analysis (PCA) is adopted to reconstruct the thermal images. The missed solder balls can be recognized explicitly in the second principal component image. Probabilistic neural network (PNN) is then established to identify the defective bump intelligently. The hot spots corresponding to the solder balls are segmented from the PCA reconstructed image, and statistic parameters are calculated. To characterize the thermal properties of solder bump quantitatively, three representative features are selected and used as the input vector in PNN clustering. The results show that the actual outputs and the expected outputs are consistent in identification of the missed solder balls, and all the bumps were recognized accurately, which demonstrates the viability of the PNN in effective defect inspection in high-density microelectronic packaging.

  20. The use of infrared thermography and accelerometers for remote monitoring of dairy cow health and welfare.

    PubMed

    Stewart, M; Wilson, M T; Schaefer, A L; Huddart, F; Sutherland, M A

    2017-03-02

    Increasing reliance on automated systems on-farm has led to a need for remote monitoring of health and welfare. We aimed to validate 2 methods that could be integrated into automated systems currently in use: infrared thermography (IRT) to measure respiration rate (RR), and accelerometers to measure the flinch, step, kick (FSK) response and assessing stress and discomfort. We monitored 22 multiparous, nonlactating, Friesian and Friesian × Jersey cows (average 5.1 yr of age) during a baseline period (2 min), a restraint in a crush (2 min), and then a recovery period after exposure to a startle (2 min). We measured RR with continuous IRT imaging of airflow through the nostrils and by counting flank movements from video and live recordings. We recorded heart rate (HR) and HR variability using HR monitors, and we recorded FSK from continuous video analysis of leg movements and indirectly using accelerometers attached to both hind legs. The FSK response was scored between 1 and 4 based on the height and direction of each leg movement. We observed no change in RR, HR variability, or FSK in response to the startle; however, HR increased briefly by 10 bpm. Bland-Altman plots indicated good agreement between the different methods of measuring RR, with average differences of -0.01 ± 0.87, 0.83 ± 0.57, and 0.37 ± 1.02 breaths/min for video versus live, IRT versus live and IRT versus video, respectively. Acceleration was also highly correlated with FSK scores of ≤3 (R(2) = 0.96) and ≤2 (R(2) = 0.89) and moderately correlated with FSK scores of 1 (R(2) = 0.66) over the 4-min sampling period. The results show that accelerometers can provide an indirect measure of the FSK response, and IRT can be used reliably to measure RR. With further development, both technologies could be integrated into existing systems for remote monitoring of dairy cows' health and welfare on-farm.

  1. Infrared thermography in the detection of brown adipose tissue in humans

    PubMed Central

    Jang, Christina; Jalapu, Sandya; Thuzar, Moe; Law, Phillip W; Jeavons, Susanne; Barclay, Johanna L.; Ho, Ken K.Y.

    2014-01-01

    Abstract PET‐CT using 18F‐FDG is employed for detecting brown adipose tissue (BAT) in humans. Alternative methods are needed because of the radiation and cost of PET‐CT imaging. The aim was to evaluate the accuracy of infrared thermography (IRT) in detecting human BAT benchmarked to PET‐CT imaging. Seventeen individuals underwent a total of 29 PET‐CT scans, 12 of whom were studied twice, after 2 h of cold stimulation at 19°C, in parallel with measurement of skin temperatures overlying the supraclavicular (SCV) fossa and the lateral upper chest (control), before and after cold stimulation. Of the 29 scans, 20 were BAT positive after cold stimulation. The mean left SCV temperature tended to be higher in the BAT‐positive group before and during cooling. It was significantly higher (P =0.04) than the temperature of the control area, which fell significantly during cooling in the BAT‐positive (−1.2 ± 0.3°C, P =0.002) but not in the negative (−0.2 ± 0.4°C) group. The temperature difference (Δtemp) between left SCV and chest increased during cooling in the BAT‐positive (1.2 ± 0.2 to 2.0 ± 0.3°C, P <0.002) but not in the negative group (0.6 ± 0.1 to 0.7 ± 0.1°C). A Δtemp of 0.9°C conferred a positive predictive value of 85% for SCV BAT, superior to that of SCV temperature. The findings were similar on the right. In conclusion, the Δtemp is significantly and consistently greater in BAT‐positive subjects. The Δtemp quantified by IRT after 2‐h cooling shows promise as a noninvasive convenient technique for studying SCV BAT function. PMID:25413316

  2. Diverging drought resistance of Scots pine provenances revealed by infrared thermography and mortality

    NASA Astrophysics Data System (ADS)

    Seidel, Hannes; Schunk, Christian; Matiu, Michael; Menzel, Annette

    2016-04-01

    Climate warming and more frequent and severe drought events will alter the adaptedness and fitness of tree species. Especially, Scots pine forests have been affected above average by die-off events during the last decades. Assisted migration of adapted provenances might help alleviating impacts by recent climate change and successfully regenerating forests. However, the identification of suitable provenances based on established ecophysiological methods is time consuming, sometimes invasive, and data on provenance-specific mortality are lacking. We studied the performance, stress and survival of potted Scots pine seedlings from 12 European provenances grown in a greenhouse experiment with multiple drought and warming treatments. In this paper, we will present results of drought stress impacts monitored with four different thermal indices derived from infrared thermography imaging as well as an ample mortality study. Percent soil water deficit (PSWD) was shown to be the main driver of drought stress response in all thermal indices. In spite of wet and dry reference surfaces, however, fluctuating environmental conditions, mainly in terms of air temperature and humidity, altered the measured stress response. In linear mixed-effects models, besides PSWD and meteorological covariates, the factors provenance and provenance - PSWD interactions were included. The explanatory power of the models (R2) ranged between 0.51 to 0.83 and thus, provenance-specific responses to strong and moderate drought and subsequent recovery were revealed. However, obvious differences in the response magnitude of provenances to drought were difficult to explicitly link to general features such Mediterranean - continental type or climate at the provenances' origin. We conclude that seedlings' drought resistance may be linked to summer precipitation and their experienced stress levels are a.o. dependent on their above ground dimensions under given water supply. In respect to mortality, previous

  3. Practical identification of moisture sources in building assemblies using infrared thermography

    NASA Astrophysics Data System (ADS)

    McIntosh, Gregory B.; Colantonio, Antonio

    2015-05-01

    Water, in its various phases, in any environment other than desert (hot or cold) conditions, is the single most destructive element that causes deterioration of materials and failure of building assemblies. It is the key element present in the formation of mold and fungi that lead to indoor air quality problems. Water is the primary element that needs to be managed in buildings to ensure human comfort, health and safety. Under the right thermodynamic conditions the detection of moisture in its various states is possible through the use of infrared thermography for a large variety of building assemblies and materials. The difficulty is that moisture is transient and mobile from one environment to another via air movement, vapor pressure or phase change. Building materials and enclosures provide both repositories and barriers to this moisture movement. In real life steady state conditions do not exist for moisture within building materials and enclosures. Thus the detection of moisture is in a constant state of transition. Sometimes you will see it and sometimes you will not. Understanding the limitations at the time of inspection will go a long way to mitigating unsatisfied clients or difficult litigation. Moisture detection can be observed by IRT via three physical mechanisms; latent heat absorption or release during phase change; a change in conductive heat transfer; and a change in thermal capacitance. Complicating the three methodologies is the factor of variable temperature differentials and variable mass air flow on, through and around surfaces being inspected. Building enclosures come in variable assembly types and are designed to perform differently in different environmental regions. Sources for moisture accumulation will vary for different environmental conditions. Detection methodologies will change for each assembly type in different ambient environments. This paper will look at the issue of the methodologies for detection of the presence of moisture and

  4. Bridge deck surface temperature monitoring by infrared thermography and inner structure identification using PPT and PCT analysis methods

    NASA Astrophysics Data System (ADS)

    Dumoulin, Jean

    2013-04-01

    One of the objectives of ISTIMES project was to evaluate the potentialities offered by the integration of different electromagnetic techniques able to perform non-invasive diagnostics for surveillance and monitoring of transport infrastructures. Among the EM methods investigated, we focused our research and development efforts on uncooled infrared camera techniques due to their promising potential level of dissemination linked to their relative low cost on the market. On the other hand, works were also carried out to identify well adapted implementation protocols and key limits of Pulse Phase Thermography (PPT) and Principal Component Thermography (PCT) processing methods to analyse thermal image sequence and retrieve information about the inner structure. So the first part of this research works addresses infrared thermography measurement when it is used in quantitative mode (not in laboratory conditions) and not in qualitative mode (vision applied to survey). In such context, it requires to process in real time thermal radiative corrections on raw data acquired to take into account influences of natural environment evolution with time, thanks to additional measurements. But, camera sensor has to be enough smart to apply in real time calibration law and radiometric corrections in a varying atmosphere. So, a complete measurement system was studied and developed [1] with low cost infrared cameras available on the market. In the system developed, infrared camera is coupled with other sensors to feed simplified radiative models running, in real time, on GPU available on small PC. The whole measurement system was implemented on the "Musmeci" bridge located in Potenza (Italy). No traffic interruption was required during the mounting of our measurement system. The infrared camera was fixed on top of a mast at 6 m elevation from the surface of the bridge deck. A small weather station was added on the same mast at 1 m under the camera. A GPS antenna was also fixed at the

  5. Assessing honeybee and wasp thermoregulation and energetics—New insights by combination of flow-through respirometry with infrared thermography

    PubMed Central

    Stabentheiner, Anton; Kovac, Helmut; Hetz, Stefan K.; Käfer, Helmut; Stabentheiner, Gabriel

    2012-01-01

    Endothermic insects like honeybees and some wasps have to cope with an enormous heat loss during foraging because of their small body size in comparison to endotherms like mammals and birds. The enormous costs of thermoregulation call for optimisation. Honeybees and wasps differ in their critical thermal maximum, which enables the bees to kill the wasps by heat. We here demonstrate the benefits of a combined use of body temperature measurement with infrared thermography, and respiratory measurements of energy turnover (O2 consumption or CO2 production via flow-through respirometry) to answer questions of insect ecophysiological research, and we describe calibrations to receive accurate results. To assess the question of what foraging honeybees optimise, their body temperature was compared with their energy turnover. Honeybees foraging from an artificial flower with unlimited sucrose flow increased body surface temperature and energy turnover with profitability of foraging (sucrose content of the food; 0.5 or 1.5 mol/L). Costs of thermoregulation, however, were rather independent of ambient temperature (13–30 °C). External heat gain by solar radiation was used to increase body temperature. This optimised foraging energetics by increasing suction speed. In determinations of insect respiratory critical thermal limits, the combined use of respiratory measurements and thermography made possible a more conclusive interpretation of respiratory traces. PMID:22723718

  6. Assessing honeybee and wasp thermoregulation and energetics-New insights by combination of flow-through respirometry with infrared thermography.

    PubMed

    Stabentheiner, Anton; Kovac, Helmut; Hetz, Stefan K; Käfer, Helmut; Stabentheiner, Gabriel

    2012-04-20

    Endothermic insects like honeybees and some wasps have to cope with an enormous heat loss during foraging because of their small body size in comparison to endotherms like mammals and birds. The enormous costs of thermoregulation call for optimisation. Honeybees and wasps differ in their critical thermal maximum, which enables the bees to kill the wasps by heat. We here demonstrate the benefits of a combined use of body temperature measurement with infrared thermography, and respiratory measurements of energy turnover (O(2) consumption or CO(2) production via flow-through respirometry) to answer questions of insect ecophysiological research, and we describe calibrations to receive accurate results.To assess the question of what foraging honeybees optimise, their body temperature was compared with their energy turnover. Honeybees foraging from an artificial flower with unlimited sucrose flow increased body surface temperature and energy turnover with profitability of foraging (sucrose content of the food; 0.5 or 1.5 mol/L). Costs of thermoregulation, however, were rather independent of ambient temperature (13-30 °C). External heat gain by solar radiation was used to increase body temperature. This optimised foraging energetics by increasing suction speed.In determinations of insect respiratory critical thermal limits, the combined use of respiratory measurements and thermography made possible a more conclusive interpretation of respiratory traces.

  7. Infrared thermography and ultrasound C-scan for non-destructive evaluation of 3D carbon fiber materials: a comparative study

    NASA Astrophysics Data System (ADS)

    Zhang, Hai; Genest, Marc; Robitaille, Francois; Maldague, Xavier; West, Lucas; Joncas, Simon; Leduc, Catherine

    2015-05-01

    3D Carbon fiber polymer matrix composites (3D CF PMCs) are increasingly used for aircraft construction due to their exceptional stiffness and strength-to-mass ratios. However, defects are common in the 3D combining areas and are challenging to inspect. In this paper, Stitching is used to decrease these defects, but causes some new types of defects. Infrared NDT (non-destructive testing) and ultrasound NDT are used. In particular, a micro-laser line thermography technique (micro-LLT) and a micro-laser spot thermography (micro-LST) with locked-in technique are used to detect the micro-defects. In addition, a comparative study is conducted by using pulsed thermography (PT), vibrothermography (VT). In order to confirm the types of the defects, microscopic inspection is carried out before NDT work, after sectioning and polishing a small part of the sample..

  8. IR Thermography NDE of ISS Radiator Panels

    NASA Technical Reports Server (NTRS)

    Koshti, Ajay; Winfree, William; Morton, Richard; Wilson, Walter; Reynolds, Gary

    2010-01-01

    The presentation covers an active and a passive infrared (IR) thermography for detection of delaminations in the radiator panels used for the International Space Station (ISS) program. The passive radiator IR data was taken by a NASA astronaut in an extravehicular activity (EVA) using a modified FLIR EVA hand-held camera. The IR data could be successfully analyzed to detect gross facesheet disbonds. The technique used the internal hot fluid tube as the heat source in analyzing the IR data. Some non-flight ISS radiators were inspected using an active technique of IR flash thermography to detect disbond of face sheet with honeycomb core, and debonds in facesheet overlap areas. The surface temperature and radiated heat emission from flight radiators is stable during acquisition of the IR video data. This data was analyzed to detect locations of unexpected surface temperature gradients. The flash thermography data was analyzed using derivative analysis and contrast evolutions. Results of the inspection are provided.

  9. Evaluation of the limit of acceptable damage for leather products using infrared thermography

    NASA Astrophysics Data System (ADS)

    Luong, Phong M.

    1999-02-01

    The paper aims to illustrate three advantages of IR thermography as a nondestructive, noncontact and real time technique, (a) to observe the progressive damage processes and mechanisms of leather failure, and (b) to detect the occurrence of intrinsic dissipation localization. The parameter, investigated in this paper, is the heat generation due to intrinsic dissipation caused by inelasticity and/or inelasticity of leather. It readily describes the damage location and the failure evolution of leather for sport foot-wear.

  10. Infrared thermography based on artificial intelligence for carpal tunnel syndrome diagnosis.

    PubMed

    Jesensek Papez, B; Palfy, M; Turk, Z

    2008-01-01

    Thermography for the measurement of surface temperatures is well known in industry, although is not established in medicine despite its safety, lack of pain and invasiveness, easy reproducibility, and low running costs. Promising results have been achieved in nerve entrapment syndromes, although thermography has never represented a real alternative to electromyography. Here an attempt is described to improve the diagnosis of carpal tunnel syndrome with thermography using a computer-based system employing artificial neural networks to analyse the images. Method reliability was tested on 112 images (depicting the dorsal and palmar sides of 26 healthy and 30 pathological hands), with the hand divided into 12 segments and compared relative to a reference. Palmar segments appeared to have no beneficial influence on classification outcome, whereas dorsal segments gave improved outcome with classification success rates near to or over 80%, and finger segments influenced by the median nerve appeared to be of greatest importance. These are preliminary results from a limited number of images and further research will be undertaken as our image database grows.

  11. Detection and assessment of electrocution in endangered raptors by infrared thermography

    PubMed Central

    2013-01-01

    Background Most European birds of prey find themselves in a poor state of conservation, with electrocution as one of the most frequent causes of unnatural death. Since early detection of electrocution is difficult, treatment is usually implemented late, which reduces its effectiveness. By considering that electrocution reduces tissue temperature, it may be detectable by thermography, which would allow a more rapid identification. Three individuals from three endangered raptor species [Spanish imperial eagle (Aquila adalberti), Lammergeier (Gypaetus barbatus) and Osprey (Pandion haliaetus)] were studied thermographically from the time they were admitted to a rehabilitation centre to the time their clinical cases were resolved. Cases presentation The three raptors presented lesions lacking thermal bilateral symmetry and were consistent with electrocution of feet, wings and eyes, visible by thermography before than clinically; lesions were well-defined and showed a lower temperature than the surrounding tissue. Some lesions evolved thermally and clinically until the appearance of normal tissue recovered, while others evolved and became necrotic. A histopathological analysis of a damaged finger amputated off a Lammergeier, and the necropsy and histopathology examination of an osprey, confirmed the electrocution diagnosis. Conclusions These results suggest that thermography is effective and useful for the objective and early detection and monitoring of electrocuted birds, and that it may prove especially useful for examining live animals that require no amputation or cannot be subjected to invasive histopathology. PMID:23880357

  12. Identification of thermal properties distribution in building wall using infrared thermography

    NASA Astrophysics Data System (ADS)

    Brouns, Jordan; Dumoulin, Jean

    2016-04-01

    [1] L. Ibos, J-P. Monchau, V. Feuillet, Y. Candau, A comparative study of in-situ measurement methods of a building wall thermal resistance using infrared thermography, in Proc. SPIE 9534, Twelfth International Conference on Quality Control by Artificial Vision 2015, 95341I (April 30, 2015); doi:10.1117/12.2185126 [2] Nassiopoulos, A., Bourquin, F., On-site building walls characterization, Numerical Heat Transfer, Part A : Applications, 63(3) :179 :200, 2013 [3] J. Brouns, Développement d'outils numériques pour l'audit énergétique des bâtiments, PhD thesis, Université Paris-Est, SIE, 2014 [4] J.-L. Lions, Contrôle optimal de systèmes gouvernés par des équations aux dérivées partielles. Book, Dunod editor, 1968.

  13. A synchronized particle image velocimetry and infrared thermography technique applied to convective mass transfer in champagne glasses

    NASA Astrophysics Data System (ADS)

    Beaumont, Fabien; Liger-Belair, Gérard; Bailly, Yannick; Polidori, Guillaume

    2016-05-01

    In champagne glasses, it was recently suggested that ascending bubble-driven flow patterns should be involved in the release of gaseous carbon dioxide (CO2) and volatile organic compounds. A key assumption was that the higher the velocity of the upward bubble-driven flow patterns in the liquid phase, the higher the volume fluxes of gaseous CO2 desorbing from the supersaturated liquid phase. In the present work, simultaneous monitoring of bubble-driven flow patterns within champagne glasses and gaseous CO2 escaping above the champagne surface was performed, through particle image velocimetry and infrared thermography techniques. Two quite emblematic types of champagne drinking vessels were investigated, namely a long-stemmed flute and a wide coupe. The synchronized use of both techniques proved that the cloud of gaseous CO2 escaping above champagne glasses strongly depends on the mixing flow patterns found in the liquid phase below.

  14. 3D thermography in non-destructive testing of composite structures

    NASA Astrophysics Data System (ADS)

    Hellstein, Piotr; Szwedo, Mariusz

    2016-12-01

    The combination of 3D scanners and infrared cameras has lead to the introduction of 3D thermography. Such analysis produces results in the form of three-dimensional thermograms, where the temperatures are mapped on a 3D model reconstruction of the inspected object. All work in the field of 3D thermography focused on its utility in passive thermography inspections. The authors propose a new real-time 3D temperature mapping method, which for the first time can be applied to active thermography analyses. All steps required to utilise 3D thermography are discussed, starting from acquisition of three-dimensional and infrared data, going through image processing and scene reconstruction, finishing with thermal projection and ray-tracing visualisation techniques. The application of the developed method was tested during diagnosis of several industrial composite structures—boats, planes and wind turbine blades.

  15. Water ingress detection in honeycomb sandwich panels by passive infrared thermography using a high-resolution thermal imaging camera

    NASA Astrophysics Data System (ADS)

    Ibarra-Castanedo, C.; Brault, L.; Marcotte, F.; Genest, M.; Farley, V.; Maldague, X.

    2012-06-01

    Water ingress in honeycomb structures is of great concern for the civil and military aerospace industries. Pressure and temperature variations during take-off and landing produce considerable stress on aircraft structures, promoting moisture ingress (by diffusion through fibers or by direct ingress through voids, cracks or unsealed joints) into the core. The presence of water (or other fluids such as kerosene, hydraulic fluid and de-icing agents) in any of its forms (gas vapor, liquid or ice) promotes corrosion, cell breakage, and induce composite layer delaminations and skin disbonds. In this study, testing specimens were produced from unserviceable parts from military aircraft. In order to simulate atmospheric conditions during landing, selected core areas were filled with measured quantities of water and then frozen in a cold chamber. The specimens were then removed from the chamber and monitored for over 20 minutes as they warm up using a cooled high-resolution infrared camera. Results have shown that detection and quantification of water ingress on honeycomb sandwich structures by passive infrared thermography is possible using a HD mid-wave infrared cameras for volumes of water as low as 0.2 ml and from a distance as far as 20 m from the target.

  16. The use of infrared thermography as a non-invasive method for fever detection in sheep infected with bluetongue virus.

    PubMed

    Pérez de Diego, Ana C; Sánchez-Cordón, Pedro J; Pedrera, Miriam; Martínez-López, Beatriz; Gómez-Villamandos, José C; Sánchez-Vizcaíno, José M

    2013-10-01

    Fever, which is closely linked to viraemia, is considered to be both the main and the earliest clinical sign in sheep infected with bluetongue virus (BTV). The aim of this study was to evaluate the potential use of infrared thermography (IRT) for early detection of fever in sheep experimentally infected with bluetongue virus serotype 1 (BTV-1) and serotype 8 (BTV-8). This would reduce animal stress during experimental assays and assist in the development of a screening method for the identification of fever in animals suspected of being infected with BTV. Rectal and infrared eye temperatures were collected before and after BTV inoculation. The two temperature measures were positively correlated (r=0.504, P<0.05). The highest correlation between rectal and infrared temperatures was observed when temperatures were above physiological levels. IRT discriminated between febrile and non-febrile sheep with a sensitivity of 85% and specificity of 97%. The results showed that eye temperature measured using IRT was a useful non-invasive method for the assessment of fever in sheep infected with BTV under experimental conditions. Further research is required to evaluate the use of IRT under field conditions to identify potentially infected animals in bluetongue surveillance programmes.

  17. The non-invasive and automated detection of bovine respiratory disease onset in receiver calves using infrared thermography.

    PubMed

    Schaefer, A L; Cook, N J; Bench, C; Chabot, J B; Colyn, J; Liu, T; Okine, E K; Stewart, M; Webster, J R

    2012-10-01

    Bovine respiratory disease complex (BRD) causes considerable economic loss and biosecurity cost to the beef industry globally and also results in significant degradation to the welfare of affected animals. The successful treatment of this disease depends on the early, timely and cost effective identification of affected animals. The objective of the present study was to investigate the use of an automated, RFID driven, noninvasive infrared thermography technology to determine BRD in cattle. Sixty-five calves averaging 220 kg were exposed to standard industry practices of transport and auction. The animals were monitored for BRD using conventional biometric signs for clinical scores, core temperatures, haematology, serum cortisol and infrared thermal values over 3 weeks. The data collected demonstrated that true positive animals for BRD based on a gold standard including core temperature, clinical score, white blood cell number and neutrophil/lymphocyte ratio displayed higher peak infrared thermal values of 35.7±0.35 °C compared to true negative animals 34.9±0.22 °C (P<0.01). The study also demonstrated that such biometric data can be non-invasively and automatically collected based on a system developed around the animal's water station. It is concluded that the deployment of such systems in the cattle industry would aid animal managers and practitioners in the identification and management of BRD in cattle populations.

  18. Dynamic Infrared Thermography Study of Blood Flow Relative to Lower Limp Position

    NASA Astrophysics Data System (ADS)

    Stathopoulos, I.; Skouroliakou, K.; Michail, C.; Valais, I.

    2015-09-01

    Thermography is an established method for studying skin temperature distribution. Temperature distribution on body surface is influenced by a variety of physiological mechanisms and has been proven a reliable indicator of various physiological disorders. Blood flow is an important factor that influences body heat diffusion and skin temperature. In an attempt to validate and further elucidate thermal models characterizing the human skin, dynamic thermography of the lower limp in horizontal and vertical position was performed, using a FLIR T460 thermographic camera. Temporal variation of temperature was recorded on five distinct points of the limp. Specific points were initially cooled by the means of an ice cube and measurements of the skin temperature were obtained every 30 seconds as the skin temperature was locally reduced and afterwards restored at its initial value. The return to thermal balance followed roughly the same pattern for all points of measurement, although the heating rate was faster when the foot was in horizontal position. Thermal balance was achieved faster at the spots that were positioned on a vein passage. Our results confirm the influence of blood flow on the thermal regulation of the skin. Spots located over veins exhibit different thermal behaviour due to thermal convection through blood flow. Changing the position of the foot from vertical to horizontal, effectively affects blood perfusion as in the vertical position blood circulation is opposed by gravity.

  19. Thermography Applied During Exercises With or Without Infrared Light-Emitting Diode Irradiation: Individual and Comparative Analysis

    PubMed Central

    Lins, Emery C.; Corazza, Adalberto Vieira; Kurachi, Cristina; Bagnato, Vanderlei Salvador

    2013-01-01

    Abstract Objective: The aim of our study was to evaluate the cutaneous temperature during an exercise on a treadmill with or without infrared light-emitting diode (LED) irradiation in postmenopausal women. Background data: Thermography is an imaging technique in which radiation emitted by a body in the middle and far infrared spectrum is detected and associated with the temperature of the body's surface. Materials and methods: Eighteen postmenopausal women were randomly divided into two groups: (1) the LED group, which performed the exercises on a treadmill associated with phototherapy (n=9) and; (2) the exercise group, which performed the exercises on a treadmill without additional phototherapy (n=9). The irradiation parameters for each women's thigh were: array of 2000 infrared LEDs (850 nm) with an area of 1,110 cm2, 100 mW, 39 mW/cm2, and 108 J/cm2 for 45 min. The submaximal constant-speed exercise on the treadmill at intensities between 85% and 90% maximal heart rate (HRmax) with or without phototherapy were performed during 45 min, to perform the thermographic analysis. Thermography images were captured before the exercise (t=0), after 10, 35, and 45 min of exercising (t=10, t=35, and t=45) and at 5 min post-exercising (t=50). Results: The LED group showed an increased cutaneous thigh temperature during the exercise (from 33.5±0.8°C to 34.6±0.9°C, p=0.03), whereas the exercise group showed a reduced cutaneous temperature (from 33.5±0.6 to 32.7±0.7°C, p=0.02). The difference between the groups was significant (p<0.05) at t=35, t=45, and t=50. Conclusions: These data indicate an improved microcirculation, and can explain one possible mechanism of action of phototherapy associated with physical exercises. PMID:23819505

  20. Surface temperature measurement of the plasma facing components with the multi-spectral infrared thermography diagnostics in tokamaks

    NASA Astrophysics Data System (ADS)

    Zhang, C.; Gauthier, E.; Pocheau, C.; Balorin, C.; Pascal, J. Y.; Jouve, M.; Aumeunier, M. H.; Courtois, X.; Loarer, Th.; Houry, M.

    2017-03-01

    For the long-pulse high-confinement discharges in tokamaks, the equilibrium of plasma requires a contact with the first wall materials. The heat flux resulting from this interaction is of the order of 10 MW/m2 for steady state conditions and up to 20 MW/m2 for transient phases. The monitoring on surface temperatures of the plasma facing components (PFCs) is a major concern to ensure safe operation and to optimize performances of experimental operations on large fusion facilities. Furthermore, this measurement is also required to study the physics associated to the plasma material interactions and the heat flux deposition process. In tokamaks, infrared (IR) thermography systems are routinely used to monitor the surface temperature of the PFCs. This measurement requires an accurate knowledge of the surface emissivity. However, and particularly for metallic materials such as tungsten, this emissivity value can vary over a wide range with both the surface condition and the temperature itself, which makes instantaneous measurement challenging. In this context, the multi-spectral infrared method appears as a very promising alternative solution. Indeed, the system has the advantage to carry out a non-intrusive measurement on thermal radiation while evaluating surface temperature without requiring a mandatory surface emissivity measurement. In this paper, a conceptual design for the multi-spectral infrared thermography is proposed. The numerical study of the multi-channel system based on the Levenberg-Marquardt (LM) nonlinear curve fitting is applied. The numerical results presented in this paper demonstrate the design allows for measurements over a large temperature range with a relative error of less than 10%. Furthermore, laboratory experiments have been performed from 200 °C to 740 °C to confirm the feasibility for temperature measurements on stainless steel and tungsten. In these experiments, the unfolding results from the multi-channel detection provide good

  1. Eye and Ear Temperature Using Infrared Thermography Are Related to Rectal Temperature in Dogs at Rest or With Exercise

    PubMed Central

    Zanghi, Brian M.

    2016-01-01

    Rectal body temperature (BT) has been documented in exercising dogs to monitor thermoregulation, heat stress risk, and performance during physical activity. Eye (BTeye) and ear (BTear) temperature measured with infrared thermography (IRT) were compared to rectal (BTrec) temperature as the reference method and assess alternative sites to track hyperthermia, possibly to establish BTeye IRT as a passive and non-contact method. BT measures were recorded at 09:00, 11:30, 12:30, and 02:30 from Labrador Retrievers (N = 16) and Beagles (N = 16) while sedentary and with 30-min play-exercise (pre- and 0, 15, 30-min post-exercise). Total exercise locomotor activity counts were recorded to compare relative intensity of play-exercise between breeds. BTrec, BTeye, and BTear were measured within 5 min of the target time. Each BT method was analyzed by analysis of variance for main effects of breed and time. Method differences were compared using Bland–Altman plots and linear regression. Sedentary BT differed by breed for BTrec (p < 0.0001), BTear (p < 0.0001), and BTeye (p = 0.06) with Labs having on average 0.3–0.8°C higher BT compared to Beagles. Readings also declined over time for BTeye (p < 0.0001) and BTear (p < 0.0001), but not for BTrec (p = 0.63) for both breeds. Total exercise (30-min) activity counts did not differ (p = 0.53) between breeds. Time and breed interaction was significant in response to exercise for both BTrec and BTear (p = 0.035 and p = 0.005, respectively), with a marginal interaction (p = 0.09) for BTeye. All the three methods detected hyperthermia with Labs having a higher increase compared to Beagles. Both BTear and BTeye were significantly (p < 0.0001) related to BTrec in all dogs with sedentary or exercise activity. The relationship between BTeye and BTrec improved when monitoring exercise hyperthermia (r = 0.674) versus measures at rest (r = 0.381), whereas BTear was significantly

  2. Eye and Ear Temperature Using Infrared Thermography Are Related to Rectal Temperature in Dogs at Rest or With Exercise.

    PubMed

    Zanghi, Brian M

    2016-01-01

    Rectal body temperature (BT) has been documented in exercising dogs to monitor thermoregulation, heat stress risk, and performance during physical activity. Eye (BTeye) and ear (BTear) temperature measured with infrared thermography (IRT) were compared to rectal (BTrec) temperature as the reference method and assess alternative sites to track hyperthermia, possibly to establish BTeye IRT as a passive and non-contact method. BT measures were recorded at 09:00, 11:30, 12:30, and 02:30 from Labrador Retrievers (N = 16) and Beagles (N = 16) while sedentary and with 30-min play-exercise (pre- and 0, 15, 30-min post-exercise). Total exercise locomotor activity counts were recorded to compare relative intensity of play-exercise between breeds. BTrec, BTeye, and BTear were measured within 5 min of the target time. Each BT method was analyzed by analysis of variance for main effects of breed and time. Method differences were compared using Bland-Altman plots and linear regression. Sedentary BT differed by breed for BTrec (p < 0.0001), BTear (p < 0.0001), and BTeye (p = 0.06) with Labs having on average 0.3-0.8°C higher BT compared to Beagles. Readings also declined over time for BTeye (p < 0.0001) and BTear (p < 0.0001), but not for BTrec (p = 0.63) for both breeds. Total exercise (30-min) activity counts did not differ (p = 0.53) between breeds. Time and breed interaction was significant in response to exercise for both BTrec and BTear (p = 0.035 and p = 0.005, respectively), with a marginal interaction (p = 0.09) for BTeye. All the three methods detected hyperthermia with Labs having a higher increase compared to Beagles. Both BTear and BTeye were significantly (p < 0.0001) related to BTrec in all dogs with sedentary or exercise activity. The relationship between BTeye and BTrec improved when monitoring exercise hyperthermia (r = 0.674) versus measures at rest (r = 0.381), whereas BTear was significantly

  3. Infrared thermography and acupuncture of the lobe of the outer ear in patients with facial pain

    NASA Astrophysics Data System (ADS)

    Rossi, Ricardo; Lluesma, Eliseo G.

    2001-03-01

    We have assessed the thermal camera to complement the clinical odontology with the clinical assistance of acupuncture. Relevant cases of study were those of patients with facial pain. This work has registered the temperatures of the microsystem of the lobe of the outer ear. The recordings were made before, during and after removing the needles. Measurements of patients' temperatures were made very two minutes for 20 minutes, and a gradual increase of temperature was observed. The thermal camera allowed to register maps (thermography) that show an area affected with pain. After thermograms were performed to odontology patients treated with acupuncture, we were able to compare the temperature distribution maps and we found that they were quasi repetitive in the same zones in several patients for a specific illness. We made this technique available to different patients with lack of good irrigation on face and neck with the aim to establish patterns.

  4. Medical thermography (digital infrared thermal imaging - DITI) in paediatric forearm fractures - A pilot study.

    PubMed

    Ćurković, S; Antabak, A; Halužan, D; Luetić, T; Prlić, I; Šiško, J

    2015-11-01

    Trauma is the most common cause of hospitalisation in children, and forearm fractures comprise 35% of all paediatric fractures. One-third of forearm fractures are distal forearm fractures, which are the most common fractures in the paediatric population. This type of fracture represents an everyday problem for the paediatric surgeon. The three phases of fracture healing in paediatric trauma are associated with skin temperature changes that can be measured and then compared with standard plain radiographs of visible callus formation, and eventually these methods can be used in everyday practice. Thermographic assessment of temperature distribution within the examined tissues enables a quick, non-contact, non-invasive measurement of their temperature. Medical thermography is used as a screening method in other parts of medicine, but the use of this method in traumatology has still not been researched.

  5. Comparison of abdominal skin temperature between fertile and infertile women by infrared thermography: A diagnostic approach.

    PubMed

    Jo, Junyoung; Kim, Hyunho

    2016-10-01

    This retrospective study aimed to evaluate the differences in abdominal temperature (AT) between fertile (n=206; age) and infertile (n=250) women between the ages of 30 and 39 years. We evaluated the differences in two distinctive skin temperatures by thermography: ΔT1 (CV8 index) - difference in temperature between the mid-abdomen (CV8 acupuncture area) and ventral upper arm (VUA) and ΔT2 (CV4 index) - difference in temperature between the lower abdomen (CV4 acupuncture area) and VUA. The results indicated that the ΔT1 and ΔT2 of infertile women were significantly lower (by 1.05°C and 0.79°C, respectively; p<0.001, both) compared to those of fertile women. Additionally, the area under the curve of ΔT1 (0.78) was greater compared to that of ΔT2 (0.736), and its threshold was set at 0.675°C, by which, the sensitivity and specificity of ΔT1 for determination of fertility were found to be 80.8% and 68.4%, respectively. In conclusion, infertility is associated with lower AT. The decrease in AT in infertile women might be due to poor blood perfusion to the core muscles and tissues of the body. These findings provide a basis for further research for evaluation of clinical feasibility of thermography for analysis of infertility in women. Further evaluation of the influence of AT on fertility outcomes is required to determine the causal relationship between AT and infertility.

  6. Detection of Air and Water-Filled Subsurface Defects in GFRP Composite Bridge Decks Using Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Halabe, Udaya B.; Roy, M.; Klinkhachorn, P.; GangaRao, Hota V. S.

    2006-03-01

    Any discontinuity within a structural component influences the transmission of thermal energy through its thickness, which leads to differences in surface temperatures just above the defective and defect-free areas. The variation in the surface temperatures are recorded using a digital infrared camera and the thermal images (thermograms) are analyzed to locate the presence of subsurface defects such as debonds and delaminations within the structure. While past studies focused on detection of air-filled subsurface defects (debonds and delaminations) in fiber reinforced polymer (GFRP) composite bridge decks using infrared thermography, this paper includes the detection of fully and partially water-filled defects as well. Simulated water-filled defects were embedded within the flange-to-flange junction of adjacent GFRP bridge deck modules to create delaminations. The deck specimens were then tested before and after the application of a 3/8″ (9.5 mm) thick polymer concrete wearing surface. It was found that water-filled delaminations as small as 2″ × 2″ × 1/16″ (51 mm × 51 mm × 1.6 mm) could be detected in case of specimens without wearing surface, but this was not possible after application of the wearing surface. The heating source considered included heater and solar radiation. Use of cooling sources such as cold water and liquid carbon dioxide were also explored. These results helped establish the limits of detection for fully and partially water-filled delaminations using Infrared Thermograpy. Additional studies included the detection of debond between 2″ (51mm) thick asphalt overlay and the underlying composite deck and it was found that air-filled debonds as small as 4″ × 4″ × 1/16″ (102 mm × 102 mm × 1.6 mm) could be detected using heater as well as solar radiation as heat sources.

  7. Aerial thermography for energy conservation

    NASA Technical Reports Server (NTRS)

    Jack, J. R.

    1978-01-01

    Thermal infrared scanning from an aircraft is a convenient and commercially available means for determining relative rates of energy loss from building roofs. The need to conserve energy as fuel costs makes the mass survey capability of aerial thermography an attractive adjunct to community energy awareness programs. Background information on principles of aerial thermography is presented. Thermal infrared scanning systems, flight and environmental requirements for data acquisition, preparation of thermographs for display, major users and suppliers of thermography, and suggested specifications for obtaining aerial scanning services were reviewed.

  8. Methodology for heat flux investigation on leading edges using infrared thermography

    NASA Astrophysics Data System (ADS)

    Corre, Y.; Gardarein, J.-L.; Dejarnac, R.; Gaspar, J.; Gunn, J. P.; Aumeunier, M.-H.; Courtois, X.; Missirlian, M.; Rigollet, F.

    2017-01-01

    During steady state plasma operation in fusion devices, leading edges of the actively cooled plasma-facing components can be impacted by plasma flux with nearly normal angle of incidence, causing local overheating. The overheating can be a critical issue in high-power machines, especially in the presence of mechanical misalignments. Due to heat diffusion through the material, the edge power overload also leads to a local increase of temperature on the top part of the tile that can be detected by the infrared imaging system (viewed from the top of the machine). In the Tore Supra tokamak, heat flux impinging on the top and the leading edge of the carbon fibre composite (CFC) flat tiles are characterized with both an infrared (IR) thermographic system and 2D thermal modelling of the tile. A specific sensor correction based on a laboratory blackbody-slit experiment has been developed to simulate the spatial resolution related effects (necessary here since the temperature gradient near the leading edge is smaller than the pixel size of the IR system). The transfer function of the IR system is characterized by a Gaussian distribution function. The standard deviation is found to be σ  =  1.75 mm for a pixel size of 3.1 mm. The heat flux calculation is applied to CFC flat tiles and, after being processed with the transfer function, compared to experimental IR data for two geometrical situations: one with 0.2 mm misalignment between two adjacent tiles and the other without misalignment (well-aligned tiles). The heat flux ratio between the leading edge and top is found to be ~25 in the case of the protruding tile, which is lower than the expected ratio using the guiding-centre ballistic approximation with no cross-field heat flux (57).

  9. Cloud2IR: Infrared thermography and environmental sensors integrated in an autonomoussystem for long term monitoring of structures

    NASA Astrophysics Data System (ADS)

    Crinière, Antoine; Dumoulin, Jean; Mevel, Laurent; Andrade-Barroso, Guillermo

    2016-04-01

    acquisition scenario the local storage management and the network management through SFTP or SOAP for the OGC frame. The data side only need an XML configuration file and if a configuration change occurs in time the system is automatically restarted with the new value. Cloud2IR has been deployed on field since several Monthat the SenseCity outdoor test bed in Marne La Vallée (France)[4]. The next step will be the full standardisation of the system and possibly the full separation between the sensor side and the data side which can be seen at term as an external framework. References: [1] A Crinière, J Dumoulin, L Mevel, G Andrade-Barosso, M Simonin. The Cloud2SM Project.European Geosciences Union General Assembly (EGU2015), Apr 2015, Vienne, Austria. 2015. [2] J Dumoulin, A Criniere, and R Averty. The detection and thermal characterization of the inner structure of the 'musmeci' bridge deck by infrared thermography monitoring. Journal Of Geophysics And Engineering doi:10.1088/1742-2132/10/6/064003, Vol 10, 2013. [3] J Dumoulin, R Averty. Development of an infrared system coupled with a weather station for real time atmospheric corrections using GPU computing: Application to bridge monitoring, in Proc of 11 th International Conference on Quantitative InfraRed Thermography, Naples Italy, 2012. [4] F Derkx, B Lebental, T Bourouina, Frédéric B, C Cojocaru, and al..The Sense-City project.XVIIIth Symposium on Vibrations, Shocks and Noise, Jul 2012, France. 9p, 2012.

  10. Characterization of pores in high pressure die cast aluminum using active thermography and computed tomography

    NASA Astrophysics Data System (ADS)

    Maierhofer, Christiane; Myrach, Philipp; Röllig, Mathias; Jonietz, Florian; Illerhaus, Bernhard; Meinel, Dietmar; Richter, Uwe; Miksche, Ronald

    2016-02-01

    Larger high pressure die castings (HPDC) and decreasing wall thicknesses are raising the issue of casting defects like pores in aluminum structures. Properties of components are often strongly influenced by inner porosity. As these products are being established more and more in lightweight construction (e.g. automotive and other transport areas), non-destructive testing methods, which can be applied fast and on-site, are required for quality assurance. In this contribution, the application of active thermography for the direct detection of larger pores is demonstrated. The analysis of limits and accuracy of the method are completed by numerical simulation and the method is validated using computed tomography.

  11. Applications of infrared thermography for nondestructive testing of fatigue cracks in steel bridges

    NASA Astrophysics Data System (ADS)

    Sakagami, Takahide; Izumi, Yui; Kobayashi, Yoshihiro; Mizokami, Yoshiaki; Kawabata, Sunao

    2014-05-01

    In recent years, fatigue crack propagations in aged steel bridge which may lead to catastrophic structural failures have become a serious problem. For large-scale steel structures such as orthotropic steel decks in highway bridges, nondestructive inspection of deteriorations and fatigue damages are indispensable for securing their safety and for estimating their remaining strength. As conventional NDT techniques for steel bridges, visual testing, magnetic particle testing and ultrasonic testing have been commonly employed. However, these techniques are time- and labor- consuming techniques, because special equipment is required for inspection, such as scaffolding or a truck mount aerial work platform. In this paper, a new thermography NDT technique, which is based on temperature gap appeared on the surface of structural members due to thermal insulation effect of the crack, is developed for detection of fatigue cracks. The practicability of the developed technique is demonstrated by the field experiments for highway steel bridges in service. Detectable crack size and factors such as measurement time, season or spatial resolution which influence crack detectability are investigated.

  12. Infrared thermography for monitoring heat generation in a linear friction welding process of Ti6Al4V alloy

    NASA Astrophysics Data System (ADS)

    Maio, L.; Liberini, M.; Campanella, D.; Astarita, A.; Esposito, S.; Boccardi, S.; Meola, C.

    2017-03-01

    The increasing use of titanium alloys in a wider range of applications requires the development of new techniques and processes capable to decrease production costs and manufacturing times. In this regard welding and other joining techniques play an important role. Today, solid state friction joining processes, such as friction stir welding, friction spot welding, inertia friction welding, continuous-drive friction welding and linear friction welding (LFW), represent promising methods for part manufacturing. They allow for joining at temperature essentially below the melting point of the base materials being joined, without the addition of filler metal. However, the knowledge of temperature is essential to understand and model the phenomena involved in metal welding. A global measured value represents only a clue of the heat generation during the process; while, a deep understanding of welding thermal aspects requires temperature field measurement. This paper is focused on the use of infrared thermography applied to the linear friction welding process of Ti6Al4V alloy. The attention is concentrated on thermal field that develops on the outer wall of the two parts to be joined (i.e. heat generated in the friction zone), and on the maximum temperature that characterizes the process before and after the flash formation.

  13. How good is this food? A study on dogs' emotional responses to a potentially pleasant event using infrared thermography.

    PubMed

    Travain, Tiziano; Colombo, Elisa Silvia; Grandi, Laura Clara; Heinzl, Eugenio; Pelosi, Annalisa; Prato Previde, Emanuela; Valsecchi, Paola

    2016-05-15

    Understanding how animals express positive emotions is becoming an interesting and promising area of research in the study of animal emotions and affective experiences. In the present study, we used infrared thermography in combination with behavioral measures, heart rate (HR) and heart rate variability (HRV), to investigate dogs' emotional responses to a potentially pleasant event: receiving palatable food from the owner. Nineteen adult pet dogs, 8 females and 11 males, were tested and their eye temperature, HR, HRV and behavior were recorded during a 30-minutestestconsisting of three 10-minute consecutive phases: Baseline (Phase 1), positive stimulation through the administration of palatable treats (Feeding, Phase 2) and Post-feeding condition following the positive stimulation (Phase 3). Dogs' eye temperature and mean HR significantly increased during the positive stimulation phase compared with both Baseline and Post-feeding phases. During the positive stimulation with food (Phase 2), dogs engaged in behaviors indicating a positive emotional state and a high arousal, being focused on food treats and increasing tail wagging. However, there was no evidence of an increase in HRV during Phase 2 compared to the Phase 1, with SDNN significantly increasing only in Phase 3, after the positive stimulation occurred. Overall results point out that IRT may be a useful tool in assessing emotional states in dogs in terms of arousal but fails to discriminate emotional valence, whose interpretation cannot disregard behavioral indexes.

  14. Evaluation of equivalent defect heat generation in carbon epoxy composite under powerful ultrasonic stimulation by using infrared thermography

    NASA Astrophysics Data System (ADS)

    Derusova, D. A.; Vavilov, V. P.; Pawar, S. S.

    2015-04-01

    Low velocity impact is a frequently observed event during the operation of an aircraft composite structure. This type of damage is aptly called as “blind-side impact damage” as it is barely visible as a dent on the impacted surface, but may produce extended delaminations closer to the rear surface. One-sided thermal nondestructive testing is considered as a promising technique for detecting impact damage but because of diffusive nature of optical thermal signals there is drop in detectability of deeper subsurface defects. Ultrasonic Infrared thermography is a potentially attractive nondestructive evaluation technique used to detect the defects through observation of vibration-induced heat generation. Evaluation of the energy released by such defects is a challenging task. In this study, the thin delaminations caused by impact damage in composites and which are subjected to ultrasonic excitation are considered as local heat sources. The actual impact damage in a carbon epoxy composite which was detected by applying a magnetostrictive ultrasonic device is then modeled as a pyramid-like defect with a set of delaminations acting as an air-filled heat sources. The temperature rise expected on the surface of the specimen was achieved by varying energy contribution from each delamination through trial and error. Finally, by comparing the experimental temperature elevations in defective area with the results of temperature simulations, we estimated the energy generated by each defect and defect power of impact damage as a whole. The results show good correlation between simulations and measurements, thus validating the simulation approach.

  15. Infrared thermography with non-uniform heat flux boundary conditions on the rotor endwall of an axial turbine

    NASA Astrophysics Data System (ADS)

    Lazzi Gazzini, S.; Schädler, R.; Kalfas, A. I.; Abhari, R. S.

    2017-02-01

    It is technically challenging to measure heat fluxes on the rotating components of gas turbines, yet accurate knowledge of local heat loads under engine-representative conditions is crucial for ensuring the reliability of the designs. In this work, quantitative image processing tools were developed to perform fast and accurate infrared thermography measurements on 3D-shaped film-heaters directly deposited on the turbine endwalls. The newly developed image processing method and instrumentation were used to measure the heat load on the rotor endwalls of an axial turbine. A step-transient heat flux calibration technique is applied to measure the heat flux generated locally by the film heater, thus eliminating the need for a rigorously iso-energetic boundary condition. On-board electronics installed on the rotor record the temperature readings of RTDs installed in the substrate below the heaters in order to evaluate the conductive losses in the solid. Full maps of heat transfer coefficient and adiabatic wall temperature are produced for two different operating conditions, demonstrating the sensitivity of the technique to local flow features and variations in heat transfer due to Reynolds number effect.

  16. Evaluation of ocular surface temperature and retrobulbar haemodynamics by infrared thermography and colour Doppler imaging in patients with glaucoma

    PubMed Central

    Galassi, Fernando; Giambene, Barbara; Corvi, Andrea; Falaschi, Giacomo

    2007-01-01

    Background Ocular surface temperature (OST) could berelated to retrobulbar haemodynamics in patients with glaucoma. Aims To compare OST measurements in patients with glaucoma and healthy controls, and to investigate the correlation between OST, intraocular pressure (IOP) and retrobulbar haemodynamics in patients with glaucoma. Methods 32 patients with primary open‐angle glaucoma (POAG) and 40 controls were included in the study. The parameters considered both in patients with POAG and in controls were IOP and OST values measured by infrared ocular thermography. Colour Doppler imaging was used to determine haemodynamic parameters in ophthalmic artery (OA), central retinal artery (CRA) and short posterior ciliary arteries (SPCAs) in patients with POAG. Results OST values were significantly lower in patients with POAG than in controls (p<0.001). OST was negatively related with resistivity index of OA (p<0.001), CRA (p = 0.001) and SPCAs (p<0.001), and positively related with end‐diastolic velocity of OA (p = 0.02) and SPCAs (p = 0.05). Conclusion This study suggested that OST could be a marker of impaired retrobulbar haemodynamics in patients with glaucoma. PMID:17314146

  17. Use of infrared ocular thermography to assess physiological conditions of pigs prior to slaughter and predict pork quality variation.

    PubMed

    Weschenfelder, Angela V; Saucier, Linda; Maldague, Xavier; Rocha, Luiene M; Schaefer, Allan L; Faucitano, Luigi

    2013-11-01

    Infrared thermography (IRT) body temperature readings were taken in the ocular region of 258 pigs immediately before slaughter. Levels of lactate were measured in blood taken in the restrainer. Meat quality was assessed in the longissimus dorsi (LD), semimembranosus (SM), and adductor muscles. Ocular IRT (IROT) temperature was correlated with blood lactate levels (r=0.20; P=0.001), with pH taken 1hour postmortem (pH1: r=-0.18; P=0.03) and drip loss (r=0.20; P=0.02) in the LD muscle, and with pH1 in the SM muscle (r=-0.20; P=0.02). Potentially, IROT may be a useful tool to assess the physiological conditions of pigs at slaughter and predict the variation of important meat quality traits. However, the magnitude of the correlations is rather low, so a further development of image capture technique and further studies under more variable preslaughter conditions ensuring a larger pork quality variation are needed.

  18. Infrared thermography of the pig thorax: an assessment of selected regions of interest by computed tomographical and anatomical parameters.

    PubMed

    Menzel, A; Siewert, C; Gasse, H; Seifert, H; Hoeltig, D; Hennig-Pauka, I

    2015-04-01

    Current methods of diagnosis of respiratory diseases in swine are invasive, time-consuming and expensive. Infrared thermography (IRT) of the thorax might provide a new method of high specificity to select swine affected with lung alterations for further diagnostics. In this study, layer thickness of different tissues was determined in frozen thorax slices (FTS) by computed tomography (CT) and then related to skin temperatures measured by IRT in healthy pigs. The aim was to determine appropriate regions of interest (ROI) for evaluation of IRT images. Organ layer thicknesses measured in CT images correspond to those measured in FTS. Temperature differences between lung ROIs and abdomen ROIs were positively correlated with lung layer thickness at certain localizations, and negatively correlated with the thickness of the thorax wall and of inner organ layers. Reference values of differences between skin temperatures were established for two ROIs on the thorax with potential practical use for lung health status determination. Respective ROIs were located on vertical lines crossing the 7th (right) and the 10th (left) thoracic vertebrae. The presence of ribs affected skin temperature significantly.

  19. Department of National Defence's use of thermography for facilities maintenance

    NASA Astrophysics Data System (ADS)

    Kittson, John E.

    1990-03-01

    Since the late seventies DND through the Director General Works has been actively encouraging the use of thermography as an efficient and effective technique for supporting preventive maintenance quality assurance and energy conservation programs at Canadian Forces Bases (CFBs). This paper will provide an overview of DND''s experiences in the utilization of thermography for facilities maintenance applications. 1. HISTORICAL MILESTONES The following are milestones of DND''s use of thermography: a. Purchase of Infrared Equipment In 1976/77 DND purchased five AGA 750 Infrared Thermovision Systems which were distributed to commands. In 1980/81/82 six AGA liOs five AGA TPT8Os two AGA 782s and one AGA 720 were acquired. Finally DND also purchased seven AGEMA 870 systems during 1987/88. b. First and Second Interdepartaental Building Thermography Courses In 1978 and 1980 DND hosted two building thermography courses that were conducted by Public Works Canada. c. CE Thermographer Specialist Training Courses DND developed a training standard in 1983 for Construction Engineering (CE) Thermographer qualification which included all CE applications of thermography. The first annual inhouse training course was conducted at CFB Borden Ontario in 1984. These are now being conducted at the CFB Chilliwack Detachment in Vernon British Columbia. 2 . MARKETING FACILITIES MAINTENANCE IR Of paramount importance for successfully developing DND appreciation for thermography was providing familiarization training to CE staff at commands and bases. These threeday presentations emphasized motivational factors conducting thermographic surveys and utilizing infrared data of roofs electrical/mechanical systems heating plants steam distribution and building enclosures. These factors consisted mainly of the following objectives: a. preventive maintenance by locating deficiencies to be repaired b. quality assurance by verification of workmanship materials and design c. energy conservation by locating

  20. Nondestructive testing with thermography

    NASA Astrophysics Data System (ADS)

    Ibarra-Castanedo, Clemente; Tarpani, José Ricardo; Maldague, Xavier P. V.

    2013-11-01

    Thermography is a nondestructive testing (NDT) technique based on the principle that two dissimilar materials, i.e., possessing different thermo-physical properties, would produce two distinctive thermal signatures that can be revealed by an infrared sensor, such as a thermal camera. The fields of NDT applications are expanding from classical building or electronic components monitoring to more recent ones such as inspection of artworks or composite materials. Furthermore, thermography can be conveniently used as a didactic tool for physics education in universities given that it provides the possibility of visualizing fundamental principles, such as thermal physics and mechanics among others.

  1. TOPICAL REVIEW: FPA-based infrared thermography as applied to the study of cutaneous perspiration and stimulated vascular response in humans

    NASA Astrophysics Data System (ADS)

    Vainer, Boris G.

    2005-12-01

    This review gives an overview of focal plane array (FPA)-based infrared (IR) thermography as a powerful research method in the field of physiology and medicine. Comparison of the gained results with the data previously obtained by other authors with other research tools is given. Outer thermoregulatory manifestations displayed by the human organism subjected to whole-body heating (sauna bath) and physical loads (exercise bicycling) are quantitatively analysed. Some details of human body emotional sweating (psycho-physiological effect) are reported. Particular attention is paid to studying active sweat glands as individual objects. All experimental data were obtained with the help of a high-sensitivity (0.03 °C) fast 128 × 128 InAs IR detector-based thermal imaging system operating in the short-wave spectral region (2.5 to 3 µm) and perfectly suiting medical purposes. It is shown that IR thermography makes it possible to overcome limitations inherent to contact measuring means that were traditionally used before in thermal studies. It is also shown that heterogeneous thermograms displayed by organisms with disturbed inner equilibrium can be quantitatively analysed in terms of statistical parameters of related surface-temperature histograms, such as the mean temperature and the standard deviation of temperature (SDT). The increase and the decrease in SDT turned out to be typical of prolonged physical load and subsequent relaxation, and of external whole-body heating, respectively. Explanation of this result based on a hypothesis advanced within the context of the doctrine of human-organism evolution is given. Skin-temperature distribution function accompanying the relaxed organism in normality was found to closely resemble normal-distribution function. Symmetry break down and variation of the shape of this characteristic may serve as an indicator of homeostasis shift and can be used as a quantitative criterion for the latter. A new phenomenon, stable punctate

  2. Thermal monitoring of transport infrastructures by infrared thermography coupled with inline local atmospheric conditions survey

    NASA Astrophysics Data System (ADS)

    Dumoulin, J.

    2013-09-01

    An infrared system architecture (software and hardware) has been studied and developed to allow long term monitoring of transport infrastructures in a standalone configuration. It is based on the implementation of low cost infrared thermal cameras (equipped with uncooled microbolometer focal plane array) available on the market coupled with other measurement systems. All data collected feed simplified radiative models running on GPU available on small PC to produce corrected thermal map of the surveyed structure at selected time step. Furthermore, added Web-enabled capabilities of this new infrared measurement system are also presented and discussed. A prototype of this system was tested and evaluated on real infrastructure opened to traffic. Results obtained by image and signal processing are presented. Finally, conclusions and perspectives for new implementation and new functionalities are presented and discussed.

  3. Detection of internal defects in a liquid natural gas tank by use of infrared thermography

    NASA Technical Reports Server (NTRS)

    Kantsios, A. G.

    1978-01-01

    The use of an infrared scanning technique to detect defects in the secondary barrier of a liquid natural gas tank is described. The method works by detecting leak-caused temperature differences as low as 0.2 K, but can provide only an approximate idea of the extent of the defect. The nondestructive method was tested in a study of a LNG tank already at its location in a ship; the secondary barrier was located inside the tank wall. Defective areas indicated by the infrared radiometric measurements were confirmed by other probe techniques and by physical examination.

  4. Quantification of defects in composites and rubber materials using active thermography

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Bagavathiappan, S.; Reshmi, P. R.; Philip, John; Jayakumar, T.; Raj, B.

    2012-03-01

    Active (lock-in and pulsed) thermography technique is used to quantify defect features in specimens of glass fiber reinforced polymer, high density rubber, low density rubber and aluminum bonded low density rubber with artificially produced defects. The relationship between phase contrast and thermal contrast with defect features are examined. Using lock-in approach, the optimal frequencies for different specimens are determined experimentally. It is observed that with increasing defect depth, the phase contrast increases while the thermal contrast decreases. Defects with radius to depth ratio greater than 1.0 are found to be discernible. The phase difference between sound and defective region as a function of square root of excitation frequency for glass fiber reinforced polymer specimen is found to be in good agreement with the predictions of Bennet and Patty model [1]. Further, using pulsed thermography, the defects depth could be measured accurately for glass fiber reinforced polymer specimen from the thermal contrast using the analytical approach of Balageas et al. [2].

  5. Assessment of Pregnancy in the Late Gestation Mare Using Digital Infrared Thermography

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The objective of this study was to investigate use of digital infrared thermal imaging (DITI) to determine whether surface temperature gradient differences exist between pregnant and nonpregnant mares as a noncontact method to determine pregnancy status. On the day measurements were collected, each ...

  6. High temperature stress monitoring and detection using chlorophyll a fluorescence and infrared thermography in chrysanthemum (Dendranthema grandiflora).

    PubMed

    Janka, Eshetu; Körner, Oliver; Rosenqvist, Eva; Ottosen, Carl-Otto

    2013-06-01

    Modern highly insulated greenhouses are more energy efficient than conventional types. Furthermore applying dynamic greenhouse climate control regimes will increase energy efficiency relatively more in modern structures. However, this combination may result in higher air and crop temperatures. Too high temperature affects the plant photosynthetic responses, resulting in a lower rate of photosynthesis. To predict and analyse physiological responses as stress indicators, two independent experiments were conducted, to detect the effect of high temperature on photosynthesis: analysing photosystem II (PSII) and stomatal conductance (gs). A combination of chlorophyll a fluorescence, gas exchange measurements and infrared thermography was applied using Chrysanthemum (Dendranthema grandiflora Tzvelev) 'Coral Charm' as a model species. Increasing temperature had a highly significant effect on PSII when the temperature exceeded 38 °C for a period of 7 (±1.8) days. High temperature decreased the maximum photochemical efficiency of PSII (Fv/Fm), the conformation term for primary photochemistry (Fv/Fo) and performance index (PI), as well as increased minimal fluorescence (Fo). However, at elevated CO2 of 1000 μmol mol(-1) and with a photosynthetic photon flux density (PPFD) of 800 μmol m(-2) s(-1), net photosynthesis (Pn) reached its maximum at 35 °C. The thermal index (IG), calculated from the leaf temperature and the temperature of a dry and wet reference leaf, showed a strong correlation with gs. We conclude that 1) chlorophyll a fluorescence and a combination of fluorescence parameters can be used as early stress indicators as well as to detect the temperature limit of PSII damage, and 2) the strong relation between gs and IG enables gs to be estimated non-invasively, which is an important first step in modelling leaf temperature to predict unfavourable growing conditions in a (dynamic) semi closed greenhouse.

  7. Thermography instruments for predictive maintenance

    SciTech Connect

    Palko, E.

    1993-08-12

    Thermography (infrared imaging, or IR scanning) is not only the most versatile predictive maintenance technology available today; it is, in general, the most cost-effective. Plant engineering can apply a virtually unlimited variety of predictive maintenance instruments, but all are restricted regarding the types of existing and incipient problems they can detect. Inplant applications of thermography, however, are truly limited only by the extent of the plant engineer's imagination. Here are ways that thermography can be used to fight downtime in plants, and factors to consider when selecting the best instrument for particular circumstances.

  8. Infrared Thermography as Applied to Thermal Testing of Power Systems Circuit Boards.

    NASA Astrophysics Data System (ADS)

    Miles, Jonathan James

    All operational electronic equipment dissipates some amount of energy in the form of infrared radiation. Faulty electronic components on a printed circuit board can be categorized as hard (functional) or soft (latent functional). Hard faults are those which are detected during a conventional manufacturing electronic test process. Soft failures, in contrast, are those which are undetectable through conventional testing, but which manifest themselves after a product has been placed into service. Such field defective modules ultimately result in operational failure and subsequently enter a manufacturer's costly repair process. While thermal imaging systems are being used increasingly in the electronic equipment industry as a product-testing tool, applications have primarily been limited to product design or repair processes, with minimal use in a volume manufacturing environment. Use of thermal imaging systems in such an environment has mostly been limited to low-volume products or random screening of high-volume products. Thermal measurements taken in a manufacturing environment are often taken manually, thus defeating their capability of rapid data acquisition and constraining their full potential in a high-volume manufacturing process. Integration of a thermal measurement system with automated testing equipment is essential for optimal use of expensive infrared measurement tools in a high-volume manufacturing environment. However, such a marriage presents problems with respect to both existing manufacturing test processes and infrared measurement techniques. Methods are presented in this dissertation to test automatically for latent faults, those which elude detection during conventional electronic testing, on printed circuit boards. These methods are intended for implementation in a volume manufacturing environment and involve the application of infrared imaging tools. Successful incorporation of infrared testing into existing test processes requires that: PASS

  9. Infrared thermography for noninvasive real-time monitoring of HIFU ablation

    NASA Astrophysics Data System (ADS)

    Hsiao, Yi-Sing; Kumon, Ronald E.; Deng, Cheri X.

    2012-10-01

    Infrared imaging for spatiotemporal temperature measurements was explored in this study for non-contact monitoring of temperature increases generated by HIFU ablation. Using ex vivo cardiac tissue specimens, we investigated the correlations between the occurrence of events during HIFU ablation (e.g., lesion formation, cavity formation) and the 2D spatiotemporal temperature of the tissue surface measured during HIFU ablation from an infrared camera. An increase in the rate of temperature rise was observed when lesions formed at or slightly beneath the tissue surface. Spatial shifts in the maximum temperature location away from the HIFU focus were often observed with continuing HIFU exposure after lesion formation, suggesting tissue dehydration and cavitation formation during ablation with excessive heating.

  10. Emissivity measurements on historic building materials using dual-wavelength infrared thermography

    NASA Astrophysics Data System (ADS)

    Moropoulou, Antonia; Avdelidis, Nicolas P.

    2001-03-01

    The most reliable method to obtain correct emissivity values for the infrared thermographic systems and applications is to determine the emissivity of the targets to be tested. Although this approach is not possible during in situ applications, samples of the targets can be collected and measured, as in this work, in the laboratory. In the present work, the emissivity values of selected historic building materials were measured at a variety of temperatures, in the 3-5.4 micrometers and 8-12 micrometers regions of the infrared spectrum. Porous stones from the Mediterranean area and marbles, used as historic building materials, were investigated. The examined materials presented different emissivity values, caused by their surface state and microstructure. In addition, the effect of temperature and wavelength on the emissivity values of such historic building materials was also considered.

  11. Measurement of thermal parameters of a heat insulating material using infrared thermography

    NASA Astrophysics Data System (ADS)

    Chudzik, S.

    2012-01-01

    The article presents results of research developing methods for determining thermal parameters of a thermal insulating material. This method applies periodic heating as an excitation and an infrared camera is used to measure the temperature distribution on the surface of the tested material. The usefulness of known analytical solution of the inverse problem was examined in simulation study, using a three-dimensional model of the heat diffusion phenomenon in the sample of the material under test. To solve the coefficient inverse problem an approach using an artificial neural network is proposed. The measurements were performed on an experimental setup equipped with a ThermaCAM PM 595 infrared camera and a frame grabber. The experiment allowed verification of the chosen 3-D model of the heat diffusion phenomenon and proved suitability of the proposed test method.

  12. Determination of thermal contact conductance in vacuum-bagged thermoplastic prepreg stacks using infrared thermography

    NASA Astrophysics Data System (ADS)

    Baumard, Théo; De Almeida, Olivier; Menary, Gary; Le Maoult, Yannick; Schmidt, Fabrice; Bikard, Jérôme

    2016-10-01

    The infrared heating of a vacuum-bagged, thermoplastic prepreg stack of glass/PA66 was studied to investigate the influence of vacuum level on thermal contact resistance between plies. A higher vacuum level was shown experimentally to decrease the transverse heat transfer efficiency, indicating that considering only the effect of heat conduction at the plies interfaces is not sufficient to predict the temperature distribution. An inverse analysis was used to retrieve the contact resistance coefficients as a function of vacuum pressure.

  13. Using infrared thermography to determine the presence and correct placement of grouted cells in single-width concrete masonry unit (CMU) walls

    NASA Astrophysics Data System (ADS)

    Stockton, Gregory R.; Allen, Lee R.

    1999-03-01

    Determining the placement of reinforcing grout in single-width CMU (Concrete Masonry Unit) walls has, in the past, been a painstaking and destructive undertaking. Usually, a test is performed because -- by accident -- missing cells are discovered when a wall penetration is retrofitted or change order is executed, requiring that the wall be opened. Often, a hammer or hammer drill is used to punch holes where the grouting is supposed to be. The test results are used to extrapolate the extent of the problem. This method falls short, since the sample is so small, that only outright fraud can be found, and excess grouting cannot be determined. This paper discusses the results of a joint effort between Stockton Infrared Thermographic Services, Inc. (SITS) and Allen Applied Infrared Technology, Inc. (AAIT) to produce a methodology for using non-destructive infrared thermography to ensure that the design specifications are being met.

  14. Infrared Thermography of Buildings: Qualitative Analysis of Window Infiltration Loss, Federal Office Building, Burlington, Vermont.

    DTIC Science & Technology

    1977-09-01

    Aa—AON4 942 COI.D REGIONS RESEARCH MC ENGINEERING LAB HANOVER N H F/s t3i s - IPFRARED TICRMOIRAPHY OF BUILDINGS : QUALITATIVE ANALYSIS OF WIN—ETC(U...RECIPIEHT~S CATALOG NUMBER ~~~~~Specia1 ~~~~~J7_2 9 ~ 4. E ~~~~ ~~~~~~~~ 5. TYP E OF REPORT & PERIOD COVERED -ì .,INFRARED ,~HERMOGRAPHY OF~ BUILDINGS ...ua 1itative Analysis of Window Infiltration Loss~ __________________________ J Federal Office Building , ~ urlin~~ on , Vermont

  15. Non destructive testing in situ, of works of art by stimulated infra-red thermography

    NASA Astrophysics Data System (ADS)

    Candoré, Jean Charles; Bodnar, J. L.; Detalle, Vincent; Grossel, Philippe

    2010-03-01

    This paper presents various examples of assistance to the restoration of mural paintings by infra-red photothermal radiometry. First, we present the experimental device implemented for the study. Then, we show the possibility to detect separation or air voids by this technique in various works of art as the Saint Christopher of the Campanna collection of Louvre, in the painted ceilings of the abbey of Savin Saint sur Gartempe (classified with the world heritage of UNESCO) and finally in the Cocteau frescoes of the vault Saint Pierre of Villefranche sur mer.

  16. Direct Imaging of the Onset of Electrical Conduction in Silver Nanowire Networks by Infrared Thermography: Evidence of Geometrical Quantized Percolation.

    PubMed

    Sannicolo, Thomas; Muñoz-Rojas, David; Nguyen, Ngoc Duy; Moreau, Stéphane; Celle, Caroline; Simonato, Jean-Pierre; Bréchet, Yves; Bellet, Daniel

    2016-11-09

    Advancement in the science and technology of random metallic nanowire (MNW) networks is crucial for their appropriate integration in many applications including transparent electrodes for optoelectronics and transparent film heaters. We have recently highlighted the discontinuous activation of efficient percolating pathways (EPPs) for networks having densities slightly above the percolation threshold. Such networks exhibit abrupt drops of electrical resistance when thermal or electrical annealing is performed, which gives rise to a "geometrically quantized percolation". In this Letter, lock-in thermography (LiT) is used to provide visual evidence of geometrical quantized percolation: when low voltage is applied to the network, individual "illuminated pathways" can be detected, and new branches get highlighted as the voltage is incrementally increased. This experimental approach has allowed us to validate our original model and map the electrical and thermal distributions in silver nanowire (AgNW) networks. We also study the effects of electrode morphology and wire dimensions on quantized percolation. Furthermore, we demonstrate that the network failure at high temperature can also be governed by a quantized increase of the electrical resistance, which corresponds to the discontinuous destruction of individual pathways (antipercolation). More generally, we demonstrate that LiT is a promising tool for the detection of conductive subclusters as well as hot spots in AgNW networks.

  17. Non-destructive Measurement of Total Carotenoid Content in Processed Tomato Products: Infrared Lock-In Thermography, Near-Infrared Spectroscopy/Chemometrics, and Condensed Phase Laser-Based Photoacoustics—Pilot Study

    NASA Astrophysics Data System (ADS)

    Bicanic, D.; Streza, M.; Dóka, O.; Valinger, D.; Luterotti, S.; Ajtony, Zs.; Kurtanjek, Z.; Dadarlat, D.

    2015-09-01

    Carotenes found in a diversity of fruits and vegetables are among important natural antioxidants. In a study described in this paper, the total carotenoid content (TCC) in seven different products derived from thermally processed tomatoes was determined using laser photoacoustic spectroscopy (LPAS), infrared lock-in thermography (IRLIT), and near-infrared spectroscopy (NIRS) combined with chemometrics. Results were verified versus data obtained by traditional VIS spectrophotometry (SP) that served as a reference technique. Unlike SP, the IRLIT, NIRS, and LPAS require a minimum of sample preparation which enables practically direct quantification of the TCC.

  18. Infrared thermography--a non-invasive tool to evaluate thermal status of neonatal pigs based on surface temperature.

    PubMed

    Kammersgaard, T S; Malmkvist, J; Pedersen, L J

    2013-12-01

    Hypothermia is a major cause of mortality in neonatal pigs. Infrared (IR) thermography is a promising non-invasive method to assess thermal status, but has not been evaluated for use on neonatal pigs from birth. The aim of this study was to evaluate the application of IR thermography as a non-invasive tool to estimate body temperature and assess the thermal status in newborn pigs by (1) estimating the relationship between surface temperature and rectal temperature (RT) in neonatal pigs; and (2) estimating the influence of air temperature (AT), birth weight and the time from birth on the relationship between surface temperature and RT. The method was evaluated on the basis of 1695 thermograms and 915 RTs on 91 neonatal pigs born in loose farrowing pens with floor heating at 34°C, and three different ATs (15°C, 20°C and 25°C). Full-body thermograms of the back and the side of the pigs and RT were acquired at 11 sampling times between birth and 48 h after birth. The maximum (IRmax), minimum, average of the full body and ear minimum IR surface temperatures were derived from the thermograms. IRmax had the highest correlation with RT (0.82) and was therefore used in the statistical analysis. The relation of RT by IRmax depended on time at: 0 h (slope: 0.20°C, P<0.001), 0.25 h (slope: 0.42°C, P<0.01), and 0.5 and 1 h after birth (slope: 0.68°C, P<0.001). After the 1st hour (1.5 to 48 h) the relation of RT by IRmax was no longer affected by time (slope: 0.63°C, P<0.001). The agreement between RT and IRmax was improved (P<0.001) after the 1st hour (RT-IRmax 0 to 1 h: 2.02 (1.44)°C; 1.5 to 48 h: 0.95 (0.85)°C). IRmax below 30°C was indicative of piglets having RT<32°C (91.3%). The location of IRmax was identified predominantly at the base of the ears (27/50), other sites in the region of the head (12/50) and the axilla area (8/50). There was a small but significant effect of the angle as IRmax_side-IRmax_back: mean 0.20°C (P<0.001). On the basis of the low

  19. Examination of the Early Diagnostic Applicability of Active Dynamic Thermography for Burn Wound Depth Assessment and Concept Analysis.

    PubMed

    Prindeze, Nicholas J; Fathi, Payam; Mino, Matthew J; Mauskar, Neil A; Travis, Taryn E; Paul, Dereck W; Moffatt, Lauren T; Shupp, Jeffrey W

    2015-01-01

    Despite advances in perfusion imaging, burn wound imaging technology continues to lag behind that of other fields. Quantification of blood flow is able to predict time for healing, but clear assessment of burn depth is still questionable. Active dynamic thermography (ADT) is a noncontact imaging modality capable of distinguishing tissue of different thermal conductivities. Utilizing the abnormal heat transfer properties of the burn zones, we examined whether ADT was useful in the determination of burn depth in a model of early burn wound evaluation. Duroc pigs (castrated male; n = 3) were anesthetized, and two burns were created with an aluminum billet at 3 and 12 seconds. These contact times resulted in superficial partial and deep partial thickness burn wounds, respectively. ADT and laser Doppler imaging (LDI) imaging were performed every 30 minutes postburn for a total of five imaging sessions ending 150 minutes postburn. For ADT, imaging excitation was performed for 42-120 seconds with dual quartz-infrared lamps, and subsequent infrared image capture was performed for 300 seconds. MATLAB-assisted image analysis was performed to determine burn zone region of interest thermal relaxation and characteristic patterns. LDI was performed with a moorLDI system, and biopsies were captured for histology following the 150-minute imaging session. Both ADT and LDI imaging modalities are able to detect different physical properties at 30, 60, 90 120, and 150 minutes postburn with statistical significance (P < 0.05). Resultant ADT cooling curves characterize greater differences with greater stimulation and a potentially more identifiable differential cooling characteristic. Histological analysis confirmed burn depth. This preliminary work confirms that ADT can measure burn depth and is deserving of further research either as a stand-alone imaging technology or in combination with a device to assess perfusion.

  20. Recognition of wall materials through active thermography coupled with numerical simulations.

    PubMed

    Pietrarca, Francesca; Mameli, Mauro; Filippeschi, Sauro; Fantozzi, Fabio

    2016-09-01

    In the framework of historical buildings, wall thickness as well as wall constituents are not often known a priori, and active IR thermography can be exploited as a nonintrusive method for detecting what kind of material lies beneath the external plaster layer. In the present work, the wall of a historical building is subjected to a heating stimulus, and the surface temperature temporal trend is recorded by an IR camera. A hybrid numerical model is developed in order to simulate the transient thermal response of a wall made of different known materials underneath the plaster layer. When the numerical thermal contrast and the appearance time match with the experimental thermal images, the material underneath the plaster can be qualitatively identified.

  1. Two-stage neural algorithm for defect detection and characterization uses an active thermography

    NASA Astrophysics Data System (ADS)

    Dudzik, Sebastian

    2015-07-01

    In the paper a two-stage neural algorithm for defect detection and characterization is presented. In order to estimate the defect depth two neural networks trained on data obtained using an active thermography were employed. The first stage of the algorithm is developed to detect the defect by a classification neural network. Then the defects depth is estimated using a regressive neural network. In this work the results of experimental investigations and simulations are shown. Further, the sensitivity analysis of the presented algorithm was conducted and the impacts of emissivity error and the ambient temperature error on the depth estimation errors were studied. The results were obtained using a test sample made of material with a low thermal diffusivity.

  2. Infrared thermography based magnetic hyperthermia study in Fe3O4 based magnetic fluids

    NASA Astrophysics Data System (ADS)

    Lahiri, B. B.; Ranoo, Surojit; Philip, John

    2016-09-01

    Owing to the immense clinical benefits, magnetic hyperthermia is likely to emerge as an alternate cancer therapeutic procedure in the near future. Presently, radio frequency immune fiber optic based sensors are being used to monitor temperature changes during magnetic hyperthermia measurements, which have inherent limitations due to the requirement of physical contact of the sensor with the sample, contamination and temperature monitoring at a single point. Here, we investigate the field induced heating of oil based oleic acid coated Fe3O4 nanofluid, synthesized using co-precipitation method, using infrared thermal imaging (IRT) camera and compare the results with those of fiber optic temperature sensor. Experiments were performed on nanofluid samples of four different concentrations and under five different external field amplitudes. The specific absorption rate (SAR) of the samples were determined from the initial rate of temperature rise measured using both the techniques. The SAR values determined from both the techniques were in very good agreement with each other, with in an accuracy of 5%, after incorporating convection loss correction on the infrared thermal imaging data. The consecutive thermal cycling on the samples showed good thermal stability and thermal recovery. The maximum SAR obtained was 95.9 W/gFe for a sample concentration and field amplitude of 23 wt.% and 57.3 kA m-1, respectively. This study showed the efficacy and accuracy of temperature measurement using IRT during field induced heating of magnetic nanofluid and its advantages over conventional point measurements techniques for real-time, non-contact and wide area temperature mapping without sample contamination.

  3. Skin temperature evaluation by infrared thermography: Comparison of image analysis methods

    NASA Astrophysics Data System (ADS)

    Ludwig, N.; Formenti, D.; Gargano, M.; Alberti, G.

    2014-01-01

    Body temperature in medicine is a parameter indicating abnormal activity of human tissues; it is used to diagnose specific pathologies or as an indicator of the muscle activity during physical exercise.

  4. Evaluation of infrared thermography body temperature and collar-mounted accelerometer and acoustic technology for predicting time of ovulation of cows in a pasture-based system.

    PubMed

    Talukder, S; Thomson, P C; Kerrisk, K L; Clark, C E F; Celi, P

    2015-03-01

    This study was conducted to test the hypothesis that the specificity of infrared thermography (IRT) in detecting cows about to ovulate could be improved using different body parts that are less likely to be contaminated by fecal matter. In addition, the combined activity and rumination data captured by accelerometers were evaluated to provide a more accurate indication of ovulation than the activity and rumination data alone. Thermal images of 30 cows were captured for different body areas (eye, ear, muzzle, and vulva) twice daily after AM and PM milking sessions during the entire experimental period. Milk progesterone data and insemination records were used to determine the date of ovulation. Cows were fitted with SCR heat and rumination long-distance tags (SCR HR LD) for 1 month. Activity- and rumination-based estrus alerts were initially identified using default threshold values set by the manufacturer; however, a range of thresholds was also created and tested for both activity and rumination to determine the potential for higher levels of accuracy of ovulation detection. Visual assessment of mounting indicators resulted in 75% sensitivity (Se), 100% specificity (Sp), and 100% positive predictive value (PPV). Overall, IRT showed poor performance for detecting cows about to ovulate. Vulval temperature resulted in the greatest (80%) Sp but the poorest (21%) Se compared with the IRT temperatures of other body areas. The SCR HR LD tags default threshold value resulted in 78% Se, 57% Sp, and 70% PPV. Lowering the activity threshold from the default value improved the sensitivity but created a large number of false positives, which resulted in a decrease in specificity. Lowering the activity threshold to 20 resulted in a detection performance of 80% Se, 94% Sp, and 67% PPV, whereas the rumination levels achieved 35% Se, 69% Sp, and 14% PPV. The area under the curve for the activity level, rumination level, and the combined measures of activity and rumination levels

  5. Heat Production in the Voodoo Lily (Sauromatum guttatum) as Monitored by Infrared Thermography.

    PubMed

    Skubatz, H; Nelson, T A; Meeuse, B J; Bendich, A J

    1991-04-01

    The pattern of surface temperatures of the inflorescence of Sauromatum guttatum was investigated by using an infrared camera. The male flowers are weakly thermogenic on the first day of inflorescence opening (D-day) as well as on the next day (D + 1), reaching 0.5 to 1 degrees C above ambient temperature. The appendix (the upper sterile part of the inflorescence) is highly thermogenic on D-day, reaching 32 degrees C, and is faintly thermogenic on D + 1, reaching 1 degrees C above ambient temperature. The lower part of the spadix, close to the female flowers, is also thermogenic on D-day and D + 1, reaching a temperature similar to that of the appendix only on D + 1. Salicylic acid does not induce heat production in the lower part of the spadix, as it does in the appendix. Respiration of tissue slices obtained from the appendix shows that the capacity for cyanide-insensitive respiration is present in young and mature appendices. This alternative respiratory pathway is not, however, utilized in young appendix tissue, but is engaged during the maturation of that tissue.

  6. Combination of infrared thermography and reflectance spectroscopy for precise classification of hair follicle stage

    NASA Astrophysics Data System (ADS)

    Wang, Jianru; Guan, Yue; Liu, Caihua; Zhu, Dan

    2015-03-01

    Hair follicles enjoy continual cycle of anagen, catagen and telogen all life. They not only provide a unique opportunity to study the physiological mechanism of organ regeneration, but also benefit to guide the treatment of organ repair in regenerative medicine. Usually, the histological examination as a gold standard has been applied to determine the stage of hair follicle cycle, but noninvasive classification of hair cycle in vivo remains unsolved. In this study, the thermal infrared imager was applied to measure the temperature change of mouse dorsal skin with hair follicle cycle, and the change of diffuse reflectance was monitored by the optical fiber spectrometer. Histological examination was used to verify the hair follicle stages. The results indicated that the skin temperature increased at the beginning of anagen. After having stayed a high value for several days, the temperature began to decrease. At the same time, the skin diffuse reflectance decreased until the end of this period. Then the temperature increased gradually after slightly decreased when the hair follicle entered into catagen stage, and the diffuse reflectance increased at this time. In telogen, both the temperature and the diffuse reflectance went back to a steady state all the time. Sub-stages of hair follicle cycle could be distinguished based on the joint curves. This study provided a new method to noninvasively recognize the hair follicle stage, and should be valuable for the basic and therapeutic investigations on hair regeneration.

  7. Whole Body Vibration at Different Exposure Frequencies: Infrared Thermography and Physiological Effects

    PubMed Central

    Sonza, Anelise; Robinson, Caroline C.; Achaval, Matilde; Zaro, Milton A.

    2015-01-01

    The aim of this study was to investigate the effects of whole body vibration (WBV) on physiological parameters, cutaneous temperature, tactile sensitivity, and balance. Twenty-four healthy adults (25.3 ± 2.6 years) participated in four WBV sessions. They spent 15 minutes on a vibration platform in the vertical mode at four different frequencies (31, 35, 40, and 44 Hz) with 1 mm of amplitude. All variables were measured before and after WBV exposure. Pressure sensation in five anatomical regions and both feet was determined using Von Frey monofilaments. Postural sway was measured using a force plate. Cutaneous temperature was obtained with an infrared camera. WBV influences the discharge of the skin touch-pressure receptors, decreasing sensitivity at all measured frequencies and foot regions (P ≤ 0.05). Regarding balance, no differences were found after 20 minutes of WBV at frequencies of 31 and 35 Hz. At 40 and 44 Hz, participants showed higher anterior-posterior center of pressure (COP) velocity and length. The cutaneous temperature of the lower limbs decreased during and 10 minutes after WBV. WBV decreases touch-pressure sensitivity at all measured frequencies 10 min after exposure. This may be related to the impaired balance at higher frequencies since these variables have a role in maintaining postural stability. Vasoconstriction might explain the decreased lower limb temperature. PMID:25664338

  8. A new method of dynamic and static stall detection using infrared thermography

    NASA Astrophysics Data System (ADS)

    Gardner, A. D.; Wolf, C. C.; Raffel, M.

    2016-09-01

    A new method of detecting flow separation for static and pitching airfoils is described, with application to the generation of stall maps for helicopter rotors. An airfoil is heated using a lamp, and a high-speed infrared camera monitors the surface temperature. Subtracting consecutive images and performing a spatial standard deviation over a region of interest yields a single σ {DIT} value which is used to detect boundary layer separation on the airfoil. The data can be analysed to identify attached flow (low values of σ {DIT}) and separated flow (high values of σ {DIT}). Although appropriate filtering can significantly improve the signal-to-noise ratio, the method is robust regarding the exact method of analysis and the unfiltered data are sufficiently clear to be analysed without additional processing. For the test airfoil used, stall was measured up to a pitching frequency of 5 Hz, and signal-to-noise ratios indicate that it should be possible to measure stall for a pitching frequency of 20 Hz for a carbon-fibre surface with the thermal properties used.

  9. Infrared Thermography for Monitoring of Freeze-Drying Processes: Instrumental Developments and Preliminary Results

    PubMed Central

    Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

    2014-01-01

    Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from −40°C to 25°C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5°C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8°C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13°C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10°C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union 103:2088–2097, 2014 PMID:24902839

  10. Use of infrared thermography for monitoring stomatal closure in the field: application to grapevine.

    PubMed

    Jones, Hamlyn G; Stoll, Manfred; Santos, Tiago; de Sousa, Claudia; Chaves, M Manuela; Grant, Olga M

    2002-11-01

    This paper reviews and discusses strategies for the use of thermal imaging for studies of stomatal conductance in the field and compares techniques for image collection and analysis. Measurements were taken under a range of environmental conditions and on sunlit and shaded canopies to illustrate the variability of temperatures and derived stress indices. A simple procedure is presented for correcting for calibration drift within the images from the low-cost thermal imager used (SnapShot 225, Infrared Solutions, Inc.). The use of wet and dry reference surfaces as thresholds to eliminate the inclusion of non-leaf material in the analysis of canopy temperature is discussed. An index that is proportional to stomatal conductance was compared with stomatal measurements with a porometer. The advantages and disadvantages of a possible new approach to the use of thermal imagery for the detection of stomatal closure in grapevine canopies, based on an analysis of the temperature of shaded leaves, rather than sunlit leaves, are discussed. Evidence is presented that the temperature of reference surfaces exposed within the canopy can be affected by the canopy water status.

  11. Measuring skin temperature before, during and after exercise: a comparison of thermocouples and infrared thermography.

    PubMed

    Fernandes, Alex de Andrade; Amorim, Paulo Roberto dos Santos; Brito, Ciro José; de Moura, Anselmo Gomes; Moreira, Danilo Gomes; Costa, Carlos Magno Amaral; Sillero-Quintana, Manuel; Marins, João Carlos Bouzas

    2014-02-01

    Measuring skin temperature (TSK) provides important information about the complex thermal control system and could be interesting when carrying out studies about thermoregulation. The most common method to record TSK involves thermocouples at specific locations; however, the use of infrared thermal imaging (IRT) has increased. The two methods use different physical processes to measure TSK, and each has advantages and disadvantages. Therefore, the objective of this study was to compare the mean skin temperature (MTSK) measurements using thermocouples and IRT in three different situations: pre-exercise, exercise and post-exercise. Analysis of the residual scores in Bland-Altman plots showed poor agreement between the MTSK obtained using thermocouples and those using IRT. The averaged error was -0.75 °C during pre-exercise, 1.22 °C during exercise and -1.16 °C during post-exercise, and the reliability between the methods was low in the pre- (ICC = 0.75 [0.12 to 0.93]), during (ICC = 0.49 [-0.80 to 0.85]) and post-exercise (ICC = 0.35 [-1.22 to 0.81] conditions. Thus, there is poor correlation between the values of MTSK measured by thermocouples and IRT pre-exercise, exercise and post-exercise, and low reliability between the two forms of measurement.

  12. Infrared thermography for monitoring of freeze-drying processes: instrumental developments and preliminary results.

    PubMed

    Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

    2014-07-01

    Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from -40 °C to 25 °C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5 °C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8 °C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13 °C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10 °C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes.

  13. The Application Of Infrared Thermography To Solar Central Receiver Temperature Measurements Part I. Instrument Evaluation

    NASA Astrophysics Data System (ADS)

    Bergan, Nina E.; Stoddard, Mary Clare

    1985-03-01

    This report describes the instrumentation system, the calibration theory, and the error analysis of an experiment designed to measure front surface temperatures of the Barstow Solar Central Receiver panels. The instrumentation system uses an infrared detector, imaging peripherals, a collimator, and a 30 power telescope. The unique feature of this application is the large distance (200 m) between the detector and the target (1.27 cm diameter tubes). Sources of thermal radiation other than the target are found to contribute heavily to the input signal. Thus, the calibration scheme must specifically account for these background or environmental effects. During the data acquisition, two blackbody radiators at known temperatures are referenced periodically, and their output signals are used to define the calibration curves. These curves are valid as long as the environmental effects remain unchanged. The error analysis uses the Root-Sum-Square (RSS) technique for evaluating random errors. The biased errors are assumed to stem from spatial resolution problems, and are addressed using the optical transfer functions of the system. Data analysis and interpretation are covered in Part II, Receiver Evaluation.

  14. Thermography in Neurologic Practice

    PubMed Central

    Neves, Eduardo Borba; Vilaça-Alves, José; Rosa, Claudio; Reis, Victor Machado

    2015-01-01

    One kind of medical images that has been developed in the last decades is thermal images. These images are assessed by infrared cameras and have shown an exponential development in recent years. In this sense, the aim of this study was to describe possibilities of thermography usage in the neurologic practice. It was performed a systematic review in Web of Knowledge (Thompson Reuters), set in all databases which used two combination of keywords as “topic”: “thermography” and “neurology”; and “thermography” and “neurologic”. The chronological period was defined from 2000 to 2014 (the least 15 years). Among the studies included in this review, only seven were with experimental design. It is few to bring thermography as a daily tool in clinical practice. However, these studies have suggested good results. The studies of review and an analyzed patent showed that the authors consider the thermography as a diagnostic tool and they recommend its usage. It can be concluded that thermography is already used as a diagnostic and monitoring tool of patients with neuropathies, particularly in complex regional pain syndrome, and stroke. And yet, this tool has great potential for future research about its application in diagnosis of other diseases of neurological origin. PMID:26191090

  15. [The instrument for thermography].

    PubMed

    Hamaguchi, Shinsuke

    2014-07-01

    Thermography is an imaging method using the instrument to detect infrared rays emitted from the body surface, and to plot them as a distribution diagram of the temperature information. Therefore, a thermographic instrument can be assumed to measure the skin temperature of the diseased region. Such an instrument is a useful device for noninvasive and objective assessment of various diseases. Examination using a thermographic instrument can assess the autonomic dysfunction by measuring the skin blood flow involved with the sympathetic innervation. Thermography is useful in assisting the determination of the therapeutic effect. However, autonomic dysfunction should be confirmed correctly with the assessment of thermatome that shows abnormal thermal distribution in the region of the disease. Thermography should make noticeable the difference between the body temperature of abnormal and normal sites, and show the alteration of temperature. Monitoring using thermography is useful to determine the effect of sympathetic nerve block. If a thermographic instrument is used, it is important that examiners should understand the function of the instrument, as well as its advantages and disadvantages.

  16. Influence of Surface Properties on the Detection and Quantification of Voids in Concrete Structures Using Active Thermography

    NASA Astrophysics Data System (ADS)

    Maierhofer, Ch.; Röllig, M.; Arndt, R.; Kreutzbruck, M.

    2009-03-01

    Impulse thermography is an active method for quantitative investigations of the near surface region of various structures. It has recently been applied and optimized to applications in civil engineering. For quantitative analysis of data recorded on the building site, the problems are manifold. Here, the influence of the different surface properties on the detection and characterization of voids and honeycombing simulated by polystyrene cubes and cubes prepared of porous concrete are demonstrated.

  17. A novel image enhancement algorithm based on stationary wavelet transform for infrared thermography to the de-bonding defect in solid rocket motors

    NASA Astrophysics Data System (ADS)

    Liu, Tao; Zhang, Wei; Yan, Shaoze

    2015-10-01

    In this paper, a multi-scale image enhancement algorithm based on low-passing filtering and nonlinear transformation is proposed for infrared testing image of the de-bonding defect in solid propellant rocket motors. Infrared testing images with high-level noise and low contrast are foundations for identifying defects and calculating the defects size. In order to improve quality of the infrared image, according to distribution properties of the detection image, within framework of stationary wavelet transform, the approximation coefficients at suitable decomposition level is processed by index low-passing filtering by using Fourier transform, after that, the nonlinear transformation is applied to further process the figure to improve the picture contrast. To verify validity of the algorithm, the image enhancement algorithm is applied to infrared testing pictures of two specimens with de-bonding defect. Therein, one specimen is made of a type of high-strength steel, and the other is a type of carbon fiber composite. As the result shown, in the images processed by the image enhancement algorithm presented in the paper, most of noises are eliminated, and contrast between defect areas and normal area is improved greatly; in addition, by using the binary picture of the processed figure, the continuous defect edges can be extracted, all of which show the validity of the algorithm. The paper provides a well-performing image enhancement algorithm for the infrared thermography.

  18. Real view thermography

    NASA Astrophysics Data System (ADS)

    Bienkowski, L.; Homma, C.

    2013-01-01

    In this paper we present a novel approach for enhancing active thermography for nondestructive testing. In order to make the evaluation of the data more intuitive a Real View setup is presented that uses a projection technique to let the inspector view and interact with the measurement results directly on the part in a very intuitive way. Moreover we present an analysis approach using a Sobel filter of the pulse-phase result data in order to investigate the detectability of flaws by induction thermography. By projecting this information we give a visual feedback to the operator for optimizing the probability of detection.

  19. Determining directional emissivity: Numerical estimation and experimental validation by using infrared thermography

    NASA Astrophysics Data System (ADS)

    Peeters, J.; Ribbens, B.; Dirckx, J. J. J.; Steenackers, G.

    2016-07-01

    Little research has examined that inaccurate estimations of directional emissivity form a major challenge during both passive and active thermographic measurements. Especially with the increasing use of complex curved shapes and the growing precision of thermal cameras, these errors limit the accuracy of the thermal measurements. In this work we developed a technique to estimate the directional emissivity using updated numerical simulations. The reradiation on concave surfaces is examined by thermal imaging of a homogeneous heated curved metal and nylon test sample. We used finite element modelling to predict the reradiation of concave structures in order to calculate the parameters of an approximating formula for the emissivity dependent on the angle to the normal vector on each element. The differences between experimental and numerical results of the steel test sample are explained using electron microscopy imaging and the validation on different materials. The results suggest that it is possible to determine the errors of thermal imaging testing of complex shapes using a numerical model.

  20. Infrared Thermography Flight Experimentation

    NASA Technical Reports Server (NTRS)

    Blanchard, Robert C.; Carter, Matthew L.; Kirsch, Michael

    2003-01-01

    Analysis was done on IR data collected by DFRC on May 8, 2002. This includes the generation of a movie to initially examine the IR flight data. The production of the movie was challenged by the volume of data that needed to be processed, namely 40,500 images with each image (256 x 252) containing over 264 million points (pixel depth 4096). It was also observed during the initial analysis that the RTD surface coating has a different emissivity than the surroundings. This fact added unexpected complexity in obtaining a correlation between RTD data and IR data. A scheme was devised to generate IR data near the RTD location which is not affected by the surface coating This scheme is valid as long as the surface temperature as measured does not change too much over a few pixel distances from the RTD location. After obtaining IR data near the RTD location, it is possible to make a direct comparison with the temperature as measured during the flight after adjusting for the camera s auto scaling. The IR data seems to correlate well to the flight temperature data at three of the four RID locations. The maximum count intensity occurs closely to the maximum temperature as measured during flight. At one location (RTD #3), there is poor correlation and this must be investigated before any further progress is possible. However, with successful comparisons at three locations, it seems there is great potential to be able to find a calibration curve for the data. Moreover, as such it will be possible to measure temperature directly from the IR data in the near future.

  1. Combined Holographic Subsurface Radar and Infrared Thermography for Diagnosis of the Conditions of Historical Structures and Artworks

    NASA Astrophysics Data System (ADS)

    Capineri, L.; Falorni, P.; Ivashov, S.; Zhuravlev, A.; Vasiliev, I.; Razevig, V.; Bechtel, T.; Stankiewicz, G.

    2009-04-01

    of RASCAN radar and infrared thermography (IRT) as a means of alleviating the non-uniqueness problem. Coincident RASCAN and IRT images have been recorded for laboratory mock-ups of stone, wood and plaster structures and artworks containing subsurface cracks, voids, moisture, insect damage, supports, repairs, and the like. In addition, some initial side-by-side testing has been performed on actual historic structures and artworks. Since both RASCAN and IRT produce real-time, plan-view images, they are easily overlain and compared, and both can be interpreted visually - especially by persons familiar with the particular item under investigation. Because they are sensitive to completely independent physical properties (dielectric constant for RASCAN and thermal conductivity and heat capacity for IRT), this comparison can allow confident identification of target materials and conditions. Our testing confirms that both are exquisitely sensitive to hidden moisture. Finally, instrumentation for both RASCAN and IRT is commercially available, relatively low cost, and easy to use and interpret - making this combination of methods a potentially powerful tool for workers engaged in the preservation and restoration of artworks and architecture.

  2. Recent development toward the use of infrared thermography as a non destructive technique for defect detection in tungsten plasma facing components

    NASA Astrophysics Data System (ADS)

    Richou, M.; Escourbiac, F.; Missirlian, M.; Vignal, N.; Cantone, V.; Riccardi, B.

    2011-10-01

    For ITER divertor Plasma Facing Components (PFCs), tens of thousands of armor/heat sink interfaces will be produced by the industry. Statistically, there is a probability that interfaces with defects be delivered. The defect detection with Non Destructive Techniques (NDT) is then a major challenge. NDT should provide a detectability threshold below the critical defect size. For a defect located all along the axial length of a component, the critical defect size at interface is about 50° for W monoblock (resp. 6 mm for W flat tile). It is defined with thermo-mechanical fatigue behaviour under 10 MW m -2 for W monoblock (resp. 5 MW m -2 for W flat tile). The purpose of this paper is to study the armor/heat sink defect detection of tungsten components (flat tile and monoblock geometries) with SATIR test bed (Infrared thermography NDT). We demonstrate that SATIR is a relevant NDT to detect defect of W components.

  3. Applying Infrared Thermography as a Quality-Control Tool for the Rapid Detection of Proton-Electrolyte-Membrane-Fuel-Cell Catalyst-Layer-Thickness Variations

    SciTech Connect

    Aieta, N. V.; Das, P. K.; Perdue, A.; Bender, G.; Herring, A. M.; Weber, A. Z.; Ulsh, M. J.

    2012-08-01

    As fuel cells become more prominent, new manufacturing and production methods are needed to enable increased volumes with high quality. One necessary component of this industrial growth will be the accurate measurement of the variability of a wide range of material properties during the manufacturing process. In this study, a method to detect defects in fuel cell catalyst layers is investigated through experiment and mathematical simulation. The method uses infrared thermography and direct-current electronic-excitation methods to detect variations in platinum-containing catalyst-layer thickness with high spatial and temporal resolution. Data analysis, operating-condition impacts, and detection limits are explored, showing the measurement of defects on the millimeter length scale. Overall, the experimental and modeling results demonstrate great potential of this technique as a nondestructive method to measure defects that is amenable to use on roll-to-roll manufacturing lines.

  4. Different imaging methods in the comparative assessment of vascular lesions: color-coded duplex sonography, laser Doppler perfusion imaging, and infrared thermography

    NASA Astrophysics Data System (ADS)

    Urban, Peter; Philipp, Carsten M.; Weinberg, Lutz; Berlien, Hans-Peter

    1997-12-01

    Aim of the study was the comparative investigation of cutaneous and subcutaneous vascular lesions. By means of color coded duplex sonography (CCDS), laser doppler perfusion imaging (LDPI) and infrared thermography (IT) we examined hemangiomas, vascular malformations and portwine stains to get some evidence about depth, perfusion and vascularity. LDI is a helpful method to get an impression of the capillary part of vascular lesions and the course of superficial vessels. CCDS has disadvantages in the superficial perfusion's detection but connections to deeper vascularizations can be examined precisely, in some cases it is the only method for visualizing vascular malformations. IT gives additive hints on low blood flow areas or indicates arterial-venous-shunts. Only the combination of all imaging methods allows a complete assessment, not only for planning but also for controlling the laser treatment of vascular lesions.

  5. Using active thermography and modified SVM for intelligent diagnosis of solder bumps

    NASA Astrophysics Data System (ADS)

    Wei, Wei; Wei, Li; Nie, Lei; Su, Lei; Lu, Xiangning

    2015-09-01

    Solder bump technology has been used extensively in microelectronic packaging. But defect inspection becomes increasingly difficult due to the decrease of solder bumps in dimension and pitch. To overcome the shortages of traditional methods, we have developed an intelligent system using the active thermography for defects inspection of the solder bumps. A modified support vector machine (M-SVM) was investigated to solve the problem of small sample size in solder bumps classification. The chip SFA1 and SFA2 were chosen as the test vehicles. Captured thermal images were preprocessed using the improved wiener filter and moving average technique to remove the peak noise. The principal component analysis (PCA) algorithm was then adopted to reconstruct the thermal image, in which the hot spots were segmented. The statistical features corresponding to every solder bump were extracted and input into the M-SVM for solder bumps classification. The defective bumps w distinguished from the good bumps, which proves that the intelligent system using the modified SVM is effective for defects inspection in microelectronic packages.

  6. Evaluation of the variable depth resolution of active dynamic thermography on human skin

    NASA Astrophysics Data System (ADS)

    Prindeze, Nicholas J.; Hoffman, Hilary A.; Carney, Bonnie C.; Moffatt, Lauren T.; Loew, Murray H.; Shupp, Jeffrey W.

    2015-06-01

    Active dynamic thermography (ADT) is an imaging technique capable of characterizing the non-homogenous thermal conductance of damaged tissues. The purpose of this study was to determine optimal stimulation parameters and quantify the optical resolution of ADT through various depths of human skin. Excised tissue from plastic surgery operations was collected immediately following excision. A total of 12 thin to thick split-thickness grafts were harvested from 3 patients. Grafts were placed on top of a 3D printed resolution chart and thermal stimulation was applied from a 300W halogen lamp array for between 0.5-10 seconds to determine optimal parameters. Video was captured with a thermal camera, and analysis was performed by reconstructing an image from thermal gradients. In this study ADT resolved 0.445+/-0 lp/mm at a depth of 0.010", 0.356+/-0.048 lp/mm at a depth of 0.015", 0.334+/-0.027 lp/mm at a depth of 0.020" and 0.265+/-0.022 lp/mm at a depth of 0.025". The stimulus energy required for maximum resolution at each depth was 3- 4s, 8s, 12s and 12s respectively. ADT is a sensitive technique for imaging dermal structure, capable of resolving detail as fine as 1124 μm, 1427 μm, 1502 μm and 1893 μm in thin to thick split-thickness skin grafts respectively. This study has characterized a correlation between stimulus input and maximal resolution at differing depths of skin. It has also defined the functional imaging depth of ADT to below the sub-cutis, well below conventional spectrophotometric techniques.

  7. Non-destructive testing of objects of complex shape using infrared thermography: rear surface reconstruction by temporal tracking of the thermal front

    NASA Astrophysics Data System (ADS)

    Djupkep Dizeu, F. B.; Laurendeau, Denis; Bendada, Abdelhakim

    2016-12-01

    Infrared thermography allows contactless non-destructive testing of objects based on their thermal behavior. Quantitative inspection of an object aims to characterize its internal defects by estimating their size and their depth. In the field, a one-dimensional thermal model has been used for depth estimation. Unfortunately, the methods based on this model become inaccurate when the inspected object has a high thermal diffusivity, a complex shape, or when the defects, like corrosion, have a complex geometry. For such cases, a 3D formulation of the problem is needed. In this paper, we consider the defect characterization as an inverse geometry problem and we propose a new method: the rear surface reconstruction by temporal tracking of the thermal front. The idea is to follow the thermal front while it propagates inside the object. Referring to the duality time-depth, at every moment, the penetration depth of the thermal front can be estimated. As soon as the thermal front reaches the rear surface, a temperature change will be noticeable on the frontal surface. It is then possible to update the internal geometry of the object at each time step in such a way that the difference between the theoretical temperature, obtained by a 3D solver, and the experimental temperature, recorded by an infrared camera, is minimized. The proposed method shows accurate results and can address situations involving rear surfaces with complex geometry and objects with high thermal diffusivity and a complex shape.

  8. Microwave thermography: principles, methods and clinical applications.

    PubMed

    Myers, P C; Sadowsky, N L; Barrett, A H

    1979-06-01

    We review the physical principles, method of operation, measurement limitations, and potential medical applications of microwave thermography. We present detailed results of a study of breast cancer detection at 1.3 and 3.3 GHz, including the dependence of detection rates on microwave frequency, time, tumor depth, and tumor size. At 1.3 GHz, microwave thermography detects breast cancer as well as infrared thermography (true-positive rate = 0.76 when true-negative rate = 0.63). When the two methods are combined, the true-positive rate increases by about 0.1 over that of either method alone.

  9. Thermography to Inspect Insulation of Large Cryogenic Tanks

    NASA Technical Reports Server (NTRS)

    Arens, Ellen; Youngquist, Robert

    2011-01-01

    Thermography has been used in the past to monitor active, large, cryogenic storage tanks. This approach proposes to use thermography to monitor new or refurbished tanks, prior to filling with cryogenic liquid, to look for insulation voids. Thermography may provide significant cost and schedule savings if voids can be detected early before a tank is returned to service.

  10. Evidence of Different Thermoregulatory Mechanisms between Two Sympatric Scarabaeus Species Using Infrared Thermography and Micro-Computer Tomography

    PubMed Central

    Verdú, José R.; Alba-Tercedor, Javier; Jiménez-Manrique, Mónica

    2012-01-01

    In endotherms insects, the thermoregulatory mechanisms modulate heat transfer from the thorax to the abdomen to avoid overheating or cooling in order to obtain a prolonged flight performance. Scarabaeus sacer and S. cicatricosus, two sympatric species with the same habitat and food preferences, showed daily temporal segregation with S. cicatricosus being more active during warmer hours of the day in opposition to S. sacer who avoid it. In the case of S. sacer, their endothermy pattern suggested an adaptive capacity for thorax heat retention. In S. cicatricosus, an active ‘heat exchanger’ mechanism was suggested. However, no empirical evidence had been documented until now. Thermographic sequences recorded during flight performance showed evidence of the existence of both thermoregulatory mechanisms. In S. sacer, infrared sequences showed a possible heat insulator (passive thermal window), which prevents heat transfer from meso- and metathorax to the abdomen during flight. In S. cicatricosus, infrared sequences revealed clear and effective heat flow between the thorax and abdomen (abdominal heat transfer) that should be considered the main mechanism of thermoregulation. This was related to a subsequent increase in abdominal pumping (as a cooling mechanism) during flight. Computer microtomography scanning, anatomical dissections and internal air volume measurements showed two possible heat retention mechanisms for S. sacer; the abdominal air sacs and the development of the internal abdominal sternites that could explain the thermoregulation between thorax and abdomen. Our results suggest that interspecific interactions between sympatric species are regulated by very different mechanisms. These mechanisms create unique thermal niches for the different species, thereby preventing competition and modulating spatio-temporal distribution and the composition of dung beetle assemblages. PMID:22442735

  11. Study of a brittle and precious medieval rose-window by means of the integration of GPR, stress wave tests and infrared thermography

    NASA Astrophysics Data System (ADS)

    Nuzzo, L.; Masini, N.; Rizzo, E.

    2009-04-01

    The correct management and restoration of architectural monuments of high cultural interest requires a comprehensive understanding of their status of preservation, the detection of the building features, the localization of damages and possibly the identification of their causes, nature and extent. To this aim, in recent times there is a growing interest on non-destructive and non-invasive geophysical methods as an invaluable tool for correlating spatially the information gained through destructive tests, which are restricted to a few locations of the investigated structure, and to optimize the choice of their position in order to minimize their impact on the monument structural stability. Moreover, the integration of the classical geophysical techniques with emerging surface and subsurface sensing techniques (acoustics, thermography) provides a suitable methodology for a multi-scale assessment of the monument state of preservation and its material and building components, which is vital for addressing maintenance and restoration issues. The present case study focuses on the application of Ground Penetrating Radar (GPR), infrared thermography (IRT), sonic and ultrasonic tests to analyze a 13th century precious rose window in Southern Italy, affected by widespread decay and instability problems. The Cathedral of Troia (Apulia, Italy) is the masterpiece of the Apulian Romanesque architecture. Its façade is adorned with an astonishing 6 m diameter rose window consisting of 11 twin columns, in various stone and reused marbles, connected to a central oculus and to a ring of trapezoidal elements decorated with arched ribworks. Between the twin columns there are 11 triangular carved panels with different and strongly symbolic geometrical patterns. According to visual inspection, mineralogical and petrographic studies, different materials have been used for the different architectural elements: fine grained limestone for the central oculus, medium-fine grained calcarenite

  12. Measurement of bovine body and scrotal temperature using implanted temperature sensitive radio transmitters, data loggers and infrared thermography.

    PubMed

    Wallage, A L; Gaughan, J B; Lisle, A T; Beard, L; Collins, C W; Johnston, S D

    2017-03-23

    Synchronous and continuous measurement of body (BT) and scrotal temperature (ST) without adverse welfare or behavioural interference is essential for understanding thermoregulation of the bull testis. This study compared three technologies for their efficacy for long-term measurement of the relationship between BT and ST by means of (1) temperature sensitive radio transmitters (RT), (2) data loggers (DL) and (3) infrared imaging (IRI). After an initial pilot study on two bulls to establish a surgical protocol, RTs and DLs were implanted into the flank and mid-scrotum of six Wagyu bulls for between 29 and 49 days. RT frequencies were scanned every 15 min, whilst DLs logged every 30 min. Infrared imaging of the body (flank) and scrotum of each bull was recorded hourly for one 24-h period and compared to RT and DL data. After a series of subsequent heat stress studies, bulls were castrated and testicular tissue samples processed for evidence of histopathology. Radio transmitters were less reliable than DLs; RTs lost >11 % of data, whilst 11 of the 12 DLs had 0 % data loss. IRI was only interpretable in 35.8 % of images recorded. Pearson correlations between DL and RT were strong for both BT (r > 0.94, P < 0.001) and ST (r > 0.80, P < 0.001). Surgery produced temporary minor inflammation and scrotal hematoma in two animals post-surgery. Whilst scar tissue was observed at all surgical sutured sites when bulls were castrated, there was no evidence of testicular adhesion and normal active spermatogenesis was observed in six of the eight implanted testicles. There was no significant correlation of IRI with either DL or RT. We conclude that DLs provided to be a reliable continuous source of data for synchronous measurement of BT and ST.

  13. Thermography Inspection for Detection and Tracking of Composite Cylinder Damage During Load Testing

    NASA Technical Reports Server (NTRS)

    Zalameda, J. N.; Winfree, W. P.; Seebo, J. P.; Johnston, P. H.

    2010-01-01

    Two thermography techniques, passive and active, are used to detect damage initiation and progression in a cyclically loaded composite cylinder. The passive thermography tracks damage progression in real time during cyclic loading. Active flash thermography, using a flash tube enclosed within the cylinder, images delaminations in a cylinder under different loads. A differential thermography processing technique eliminates normal material variations and improves sensitivity to and sizing of delaminations. The thermography results were compared to nonimmersion ultrasonic results.

  14. Thermography inspection for detection and tracking of composite cylinder damage during load testing

    SciTech Connect

    Zalameda, J. N.; Winfree, W. P.; Johnston, P. H.; Seebo, J. P.

    2011-06-23

    Two thermography techniques, passive and active, are used to detect damage initiation and progression in a cyclically loaded composite cylinder. The passive thermography tracks damage progression in real time during cyclic loading. Active flash thermography, using a flash tube enclosed within the cylinder, images delaminations. A differential thermography processing technique eliminates normal material variations and improves sensitivity to and sizing of delaminations. The thermography results were compared to non-immersion ultrasonic results.

  15. The evaluation of evaporation by infrared thermography: A critical analysis of the measurements on the Crau test site. [France

    NASA Technical Reports Server (NTRS)

    Seguin, B.; Petit, V.; Devillard, R.; Reich, P.; Thouy, G. (Principal Investigator)

    1980-01-01

    Evapotranspiration was calculated for both the dry and irrigated zone by four methods which were compared with the energy balance method serving as a reference. Two methods did not involve the surface temperature. They are ETR(n) = R(n), liable to be valid under wet conditions and ET(eq) = (delta/delta + gamma) R(n) i.e, the first term of Penman's equation, adapted to moderately dry conditions. The methods using surface temperature were the combined energy balance aerodynamic approach and a simplified approach proposed by Jackson et al. Tests show the surface temperature methods give relatively satisfactory results both in the dry and wet zone, with a precision of 10% to 15% compared with the reference method. As was to be expected, ET(eq) gave satisfactory results only in the dry zone and ET(Rn) in the irrigated zone. Thermography increased the precision in the estimate of ET relative to the most suitable classical method by 5% to 8% and is equally suitable for both dry and wet conditions. The Jackson method does not require extensive ground measurements and the evaluation of the surface roughness.

  16. Infrared thermography as a tool to evaluate body surface temperature and its relationship with feed efficiency in Bos indicus cattle in tropical conditions.

    PubMed

    Martello, Luciane Silva; da Luz E Silva, Saulo; da Costa Gomes, Rodrigo; da Silva Corte, Rosana Ruegger Pereira; Leme, Paulo Roberto

    2016-01-01

    The aims of this study were to evaluate the use of infrared thermography (IRT) images as a tool for monitoring body surface temperature and to study its relationship with residual feed intake (RFI) in Nellore cattle. We also evaluated IRT as an indicator of feed efficiency in Bos indicus cattle. In this study, 144 Nellore steers were fed high-concentrate diets for 70 days to evaluate feedlot performance. We examined nine animals classified as high RFI and nine animals classified as low RFI by measuring rectal temperature (RT), respiratory frequency (RF), and IRT in the front, eye, ocular area, cheek, flank, ribs, rump, and front feet. The measurements were taken at 0700, 1200, and 1600 hours. The IRT temperatures measured at the eye, cheek, flank, ribs, rump, and front feet were positively associated with RF and RT. These results indicate that increases in the temperatures are associated with increased RF and RT. There was an effect in the RFI group in the front region where IRT correlates with RT. The front IRT for high-RFI cattle was lower (P < 0.01) than that for low-RFI cattle. The higher skin temperature measured by IRT for animals in the RFI group may be related to improved efficiency of thermoregulatory mechanisms because the RT remained lower in the low-RFI group. IRT can be used in the head for studies related to RFI in beef cattle.

  17. Infrared thermography as a tool to evaluate body surface temperature and its relationship with feed efficiency in Bos indicus cattle in tropical conditions

    NASA Astrophysics Data System (ADS)

    Martello, Luciane Silva; da Luz e Silva, Saulo; da Costa Gomes, Rodrigo; da Silva Corte, Rosana Ruegger Pereira; Leme, Paulo Roberto

    2016-01-01

    The aims of this study were to evaluate the use of infrared thermography (IRT) images as a tool for monitoring body surface temperature and to study its relationship with residual feed intake (RFI) in Nellore cattle. We also evaluated IRT as an indicator of feed efficiency in Bos indicus cattle. In this study, 144 Nellore steers were fed high-concentrate diets for 70 days to evaluate feedlot performance. We examined nine animals classified as high RFI and nine animals classified as low RFI by measuring rectal temperature (RT), respiratory frequency (RF), and IRT in the front, eye, ocular area, cheek, flank, ribs, rump, and front feet. The measurements were taken at 0700, 1200, and 1600 hours. The IRT temperatures measured at the eye, cheek, flank, ribs, rump, and front feet were positively associated with RF and RT. These results indicate that increases in the temperatures are associated with increased RF and RT. There was an effect in the RFI group in the front region where IRT correlates with RT. The front IRT for high-RFI cattle was lower ( P < 0.01) than that for low-RFI cattle. The higher skin temperature measured by IRT for animals in the RFI group may be related to improved efficiency of thermoregulatory mechanisms because the RT remained lower in the low-RFI group. IRT can be used in the head for studies related to RFI in beef cattle.

  18. Set-up of an experimental procedure for the measurement of thermal transmittances via infrared thermography on lab-made prototype walls

    NASA Astrophysics Data System (ADS)

    Donatelli, Antonio; Aversa, Patrizia; Luprano, Vincenza Anna Maria

    2016-11-01

    In this paper an experimental set-up measurement for the evaluation of the thermal transmittance of opaque elements has been developed. It is based on infrared thermography and it is suggested as alternative to the standard approach set by the ISO 9869:1994 based on heat flow meter (HFM) measurement which is widely accepted by scientific audience. The proposed method has been designed in order to overcome the following restrictions of HFM method: long measuring times (about 72 h), weather conditions as constant as possible and at least a difference of 10-15 °C between the temperatures of internal and external sides of walls. In this work, the alternative method proposed is widely described and applied on lab-made prototype walls: the results are encouraging, showing discrepancies with theoretical U-values, determined in accordance with international standard ISO 6946:2007, in the range -3.5 to 2.9%. The thermal transmittances were also calculated with a commercial software based on finite element analysis; the obtained results were in good agreement with the experimental ones. Moreover, the simulations pointed out that the values obtained on lab-made prototype walls are similar to those associated with partition walls which separate rooms with different environmental conditions.

  19. Heritability of body surface temperature in hens estimated by infrared thermography at normal or hot temperatures and genetic correlations with egg and feather quality.

    PubMed

    Loyau, T; Zerjal, T; Rodenburg, T B; Fablet, J; Tixier-Boichard, M; Pinard-van der Laan, M H; Mignon-Grasteau, S

    2016-10-01

    Exposure of laying hens to chronic heat stress results in loss of egg production. It should be possible to improve hen resilience to chronic heat stress by genetic selection but measuring their sensitivity through internal temperature is time consuming and is not very precise. In this study we used infrared thermography to measure the hen's capacity to dissipate heat, in a commercial line of laying hens subjected to cycles of neutral (N, 19.6°C) or high (H, 28.4°C) ambient temperatures. Mean body temperatures (BT) were estimated from 9355 infrared images of wing, comb and shank taken from 1200 hens. Genetic parameters were estimated separately for N and H temperatures. Correlations between BT and plumage condition were also investigated. Wing temperature had low heritability (0.00 to 0.09), consistent with the fact that wing temperature mainly reflects the environmental temperature and is not a zone of heat dissipation. The heritability of comb temperature was higher, from 0.15 to 0.19 in N and H conditions, respectively. Finally, the shank temperature provided the highest heritability estimates, with values of 0.20 to 0.22 in H and N conditions, respectively. Taken together, these results show that heat dissipation is partly under genetic control. Interestingly, the genetic correlation between plumage condition and shank and comb temperatures indicated that birds with poor condition plumage also had the possibility to dissipate heat through featherless areas. Genetic correlations of temperature measurements with egg quality showed that temperatures were correlated with egg width and weight, yolk brightness and yellowness and Haugh units only under H conditions. In contrast, shell colour was correlated with leg temperature only at thermo-neutrality.

  20. [Digital noninvasive microwave thermography in the diagnosis of breast disease].

    PubMed

    Fan, K H; Fan, J H; Yao, D D; Jin, W D; Yang, B G; Meng, C X; Qu, D B

    1988-05-01

    Thermography is a noninvasive technic of examination. Liquid-Crystal Thermography and Infrared Thermography have provided great help in the general survey of breast diseases during the past twenty years but not without some limitations. Recently, by applying the microwave technic clinically, progress has been made to measure minute temperature changes in the deeper tissues. Differential diagnosis of breast disease is possible by statistical calculating the temperature difference of the two breasts. A prospective study was done in 96 women who had both X ray mammography and digital noninvasive microwave thermography. 70/96 were proved by pathology. In this group of patients, the accuracy rate was 70.00% for digital microwave thermography, 81.82% for X ray mammography and 95.50% for the two combined. The false positive rates and false negative rates, advantages, disadvantages and the for general survey of breast disease of the digital microwave thermography discussed.

  1. Investigation of body and udder skin surface temperature differentials as an early indicator of mastitis in Holstein Friesian crossbred cows using digital infrared thermography technique

    PubMed Central

    Sathiyabarathi, M.; Jeyakumar, S.; Manimaran, A.; Pushpadass, Heartwin A.; Sivaram, M.; Ramesha, K. P.; Das, D. N.; Kataktalware, Mukund A.; Jayaprakash, G.; Patbandha, Tapas Kumar

    2016-01-01

    Aim: The objective of this study was to investigate the ability of infrared thermography (IRT) technique and its interrelationship with conventional mastitis indicators for the early detection of mastitis in Holstein Friesian (HF) crossbred cows. Materials and Methods: A total of 76 quarters of lactating HF crossbred (Bos indicus × Bos taurus) cows (n=19) were monitored for body temperature (i.e., eye temperature) and udder skin surface temperature (USST) before milking using forward-looking infrared (FLIR) i5 camera. Milk samples were collected from each quarter and screened for mastitis using Somatic Cell Count (SCC), Electrical Conductivity (EC), and California mastitis test. Thermographic images were analyzed using FLIR Quick Report 1.2 image analysis software. Data on body and USST were compiled and analyzed statistically using SPSS 16.0 and Sigmaplot 11. Results: The mean±standard deviation (SD) body (37.23±0.08°C) and USST (37.22±0.04°C) of non-mastitic cow did not differ significantly; however, the mean USST of the mastitis-affected quarters were significantly higher than the body temperature and USST of unaffected quarters (p<0.001). The mean±SD USST of the subclinical mastitis (SCM) and clinical mastitis-affected quarters were 38.08±0.17 °C and 38.25±0.33 °C, respectively, which is 0.72 and 1.05 °C higher than the USST temperature of unaffected quarters. The USST was positively correlated with EC (r=0.95) and SCC (r=0.93). The receiver operating characteristic curve analysis revealed a higher sensitivity for USST in early prediction of SCM with a cut-off value of >37.61°C. Conclusion: It is concluded that infrared thermal imaging technique could be used as a potential noninvasive, quick cow-side diagnostic technique for screening and early detection of SCM and clinical mastitis in crossbred cows. PMID:28096610

  2. Variations in the vulvar temperature of sows during proestrus and estrus as determined by infrared thermography and its relation to ovulation.

    PubMed

    Simões, Vasco G; Lyazrhi, Faouzi; Picard-Hagen, Nicole; Gayrard, Véronique; Martineau, Guy-Pierre; Waret-Szkuta, Agnès

    2014-11-01

    The prediction of ovulation time is one of the most important and yet difficult processes in pig production, and it has a considerable impact on the fertility of the herd and litter size. The objective of this study was to assess the vulvar skin temperature of sows during proestrus and estrus using infrared thermography and to establish a possible relationship between the variations in vulvar temperature and ovulation. The experimental group comprised 36 crossbred Large White × Landrace females, of which 6 were gilts and 30 were multiparous sows. Estrus was detected twice daily and the temperature was obtained every 6 hours from the vulvar area and from two control points in the gluteal area (Gluteal skin temperature [GST]). A third variable, vulvar-gluteal temperature (VGT) was obtained from the difference between the vulvar skin temperature and the GST values. The animals were divided into two subgroups: group A consisting of 11 animals with estrus detected at 6:00 AM, Day 4 postweaning, and group B comprising seven animals with estrus detected at 6:00 AM, Day 5 post-weaning. Both groups showed a similar trend in the VGT. The VGT increased during the proestrus, reaching a peak 24 hours before estrus in group A and 48 hours before estrus in group B. The VGT then decreased markedly reaching the lowest value in groups A and B, respectively, 12 and 6 hours after estrus. Although the time of ovulation was only estimated on the basis of a literature review, the matching between the temporal variations of the VGT values and the predicted time of the peak of estradiol secretion that ultimately leads to the ovulation processes suggests that the VGT values represent a potential predictive marker of the ovulatory events.

  3. A field trial of infrared thermography as a non-invasive diagnostic tool for early detection of digital dermatitis in dairy cows.

    PubMed

    Alsaaod, M; Syring, C; Dietrich, J; Doherr, M G; Gujan, T; Steiner, A

    2014-02-01

    Infrared thermography (IRT) was used to detect digital dermatitis (DD) prior to routine claw trimming. A total of 1192 IRT observations were collected from 149 cows on eight farms. All cows were housed in tie-stalls. The maximal surface temperatures of the coronary band (CB) region and skin (S) of the fore and rear feet (mean value of the maximal surface temperatures of both digits for each foot separately, CBmax and Smax) were assessed. Grouping was performed at the foot level (presence of DD, n=99; absence, n=304), or at the cow level (all four feet healthy, n=24) or where there was at least one DD lesion on the rear feet, n=37). For individual cows (n=61), IRT temperature difference was determined by subtracting the mean sum of CBmax and Smax of the rear feet from that of the fore feet. Feet with DD had higher CBmax and Smax (P<0.001) than healthy feet. Smax was significantly higher in feet with infectious DD lesions (M-stage: M2+M4; n=15) than in those with non-infectious M-lesions (M1+M3; n=84) (P=0.03), but this was not the case for CBmax (P=0.12). At the cow level, an optimal cut-off value for detecting DD of 0.99°C (IRT temperature difference between rear and front feet) yielded a sensitivity of 89.1% and a specificity of 66.6%. The results indicate that IRT may be a useful non-invasive diagnostic tool to screen for the presence of DD in dairy cows by measuring CBmax and Smax.

  4. Spatial Structure of Turbulent Heat Exchange at the Snow-Atmosphere Interface Inferred from Time-sequential Infrared Thermography

    NASA Astrophysics Data System (ADS)

    Christen, A.; Oldroyd, H. J.; Diebold, M.; Huwald, H.; Parlange, M. B.

    2013-12-01

    Land surfaces with a low thermal admittance, such as snow, experience fluctuations in their surface temperature (Ts) not only due to the diurnal course of the energy balance, but also on much shorter time-scales as the consequence of turbulent heat exchange between the surface and the atmospheric surface layer. High-frequency fluctuations in Ts, as reported for selected land-surfaces in the literature, are the imprint of coherent turbulent structures transporting heat away or towards the surface in the atmospheric surface layer. Our hypothesis is that spatially coherent perturbations in Ts on a snowpack can be mapped using time-sequential thermography (TST) - time series of thermal images sampled using state-of-the-art thermal cameras. The low thermal admittance of fresh snow implies that snow should respond with higher amplitudes in Ts to atmospheric forcing than many other land-surfaces, where fluctuations in Ts can be below the radiometric resolution of common thermal camera systems. On February 13 and 14, 2013 we operated an uncooled thermal camera (A320, FLIR, Wilsonville, OR, USA) over a snow covered glacier (';Glacier de la Plaine Morte', 46°22'37"N, 7°29'16" E, 2720 m a.s.l.). The thermal camera was mounted on a short 3 m mast to provide an oblique view of a uniform and flat part of the glacier upstream of the tower, with a filed of view (FOV) of 25 x 19° at 320 x 240 pixel resolution. Thermal images of the apparent surface temperature were acquired with ~5Hz and complemented by 20 Hz measurements of the atmospheric flow with three ultrasonic anemometer-thermometers (CSAT-3, CSI, Logan, UT, USA), of which one was installed in the FOV of the thermal camera. During the measurement campaign, the atmospheric surface layer was stably stratified (clear skies, air temperatures -15 to -10°C), and Ts ranged between -21 and -10°C. The snow-surface exhibited quite large fluctuations in Ts up to ×3 K over short time (within ~10-30 seconds). The extracted spatio

  5. Optically and non-optically excited thermography for composites: A review

    NASA Astrophysics Data System (ADS)

    Yang, Ruizhen; He, Yunze

    2016-03-01

    Composites, such as glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP), and adhesive bonding are being increasingly used in fields of aerospace, renewable energy, civil and architecture, and other industries. Flaws and damages are inevitable during either fabrication or lifetime of composites structures or components. Thus, nondestructive testing (NDT) are extremely required to prevent failures and to increase reliability of composite structures or components in both manufacture and in-service inspection. Infrared thermography techniques including pulsed thermography, pulsed phase thermography, and lock-in thermography have shown the great potential and advantages. Besides conventional optical thermography, other sources such as laser, eddy current, microwave, and ultrasound excited thermography are drawing increasingly attentions for composites. In this work, a fully, in-depth and comprehensive review of thermography NDT techniques for composites inspection was conducted based on an orderly and concise literature survey and detailed analysis. Firstly, basic concepts for thermography NDT were defined and introduced, such as volume heating thermography. Next, the developments of conventional optic, laser, eddy current, microwave, and ultrasound thermography for composite inspection were reviewed. Then, some case studies for scanning thermography were also reviewed. After that, the strengths and limitations of thermography techniques were concluded through comparison studies. At last, some research trends were predicted. This work containing critical overview, detailed comparison and extensive list of references will disseminates knowledge between users, manufacturers, designers and researchers involved in composite structures or components inspection by means of thermography NDT techniques.

  6. IrLaW an OGC compliant infrared thermography measurement system developed on mini PC with real time computing capabilities for long term monitoring of transport infrastructures

    NASA Astrophysics Data System (ADS)

    Dumoulin, J.; Averty, R.

    2012-04-01

    One of the objectives of ISTIMES project is to evaluate the potentialities offered by the integration of different electromagnetic techniques able to perform non-invasive diagnostics for surveillance and monitoring of transport infrastructures. Among the EM methods investigated, uncooled infrared camera is a promising technique due to its dissemination potential according to its relative low cost on the market. Infrared thermography, when it is used in quantitative mode (not in laboratory conditions) and not in qualitative mode (vision applied to survey), requires to process in real time thermal radiative corrections on raw data acquired to take into account influences of natural environment evolution with time. But, camera sensor has to be enough smart to apply in real time calibration law and radiometric corrections in a varying atmosphere. So, a complete measurement system was studied and developed with low cost infrared cameras available on the market. In the system developed, infrared camera is coupled with other sensors to feed simplified radiative models running, in real time, on GPU available on small PC. The system studied and developed uses a fast Ethernet camera FLIR A320 [1] coupled with a VAISALA WXT520 [2] weather station and a light GPS unit [3] for positioning and dating. It can be used with other Ethernet infrared cameras (i.e. visible ones) but requires to be able to access measured data at raw level. In the present study, it has been made possible thanks to a specific agreement signed with FLIR Company. The prototype system studied and developed is implemented on low cost small computer that integrates a GPU card to allow real time parallel computing [4] of simplified radiometric [5] heat balance using information measured with the weather station. An HMI was developed under Linux using OpenSource and complementary pieces of software developed at IFSTTAR. This new HMI called "IrLaW" has various functionalities that let it compliant to be use in

  7. Recovery of normal testicular temperature after scrotal heat stress in rams assessed by infrared thermography and its effects on seminal characteristics and testosterone blood serum concentration.

    PubMed

    Alves, Maíra Bianchi Rodrigues; Andrade, André Furugen Cesar de; Arruda, Rubens Paes de; Batissaco, Leonardo; Florez-Rodriguez, Shirley Andrea; Oliveira, Bruna Marcele Martins de; Torres, Mariana Andrade; Lançoni, Renata; Ravagnani, Gisele Mouro; Prado Filho, Roberto Romano do; Vellone, Vinícius Silva; Losano, João Diego de Agostini; Franci, Celso Rodrigues; Nichi, Marcílio; Celeghini, Eneiva Carla Carvalho

    2016-08-01

    thiobarbituric acid reactive substances (TBARSs; P = 0.05), and DNA integrity (P = 0.0004). These semen characteristics were negatively affected 21 days after IN, and excluding induced TBARSs and abnormalities, recovered 35 days afterward; induced TBARSs just were affected after 49 days of IN; sperm abnormalities just recovered after 63 days. Testosterone blood serum concentration was lesser in insulated rams (P = 0.03). Thus, the difference of 1.12 °C between RT and testicular temperature impacts semen quality and testosterone blood serum concentration. Moreover, this study shows that rams can recover testes temperature efficiently toward IN and that infrared thermography is an efficient tool to identify differences on SSMT.

  8. Dynamic thermography in diagnostics of onychomycosis

    NASA Astrophysics Data System (ADS)

    Fryca, Jaroslaw; Nowakowski, Antoni; Urbanowski, Slawomir

    2004-07-01

    The paper shows the results of the research on the active dynamic thermography used for diagnostics of onychomycosis and progress of the healing process. It seems that the most essential factor affecting the development of mycosis in nails is the microcirculation in the tissue close to the nail. Active dynamic thermography may prove to be a new diagnostic method and a sufficient tool for measurements of this parameter.

  9. Using Noncontact Infrared Thermography for Long-term Monitoring of Foot Temperatures in a Patient with Diabetes Mellitus.

    PubMed

    Staffa, Erik; Bernard, Vladan; Kubíček, Luboš; Vlachovský, Robert; Vlk, Daniel; Mornstein, Vojtěch; Staffa, Robert

    2016-04-01

    Foot complications in persons with diabetes mellitus (DM) are associated with substantial costs and loss of quality of life. Increasing evidence suggests changes in skin temperature, measured using an infrared thermographic system (IRT), may be a predictor of foot ulcer development in patients with DM. The purpose of this case study is to describe the long-term IRT findings and overall clinical outcomes of a patient with DM and peripheral vascular disease. Foot temperature measurements using IRT were obtained slightly more than 1 year before and immediately following endovascular treatment of a 76-year-old man, a nonsmoker with type 2 DM, hypertension, and ischemic heart disease with cardiac arrhythmia. Although he was otherwise asymptomatic, the infrared measurement showed an average temperature difference of 2.3˚ C between the left and right foot until he developed a small, trauma-induced wound on the left foot, at which time left foot temperature increased. He was diagnosed with rectosigmoid adenocarcinoma, underwent surgery and chemotherapy, and subsequently was evaluated for peripheral vascular disease. Before undergoing peripheral angiography and percutaneous transluminal angioplasty, IRT evaluation showed a hot spot on the left heel. Immediately following endovascular treatment, the mean temperature difference between the right and left foot was low (0.2˚ C), but a Stage I pressure ulcer was visible on the left heel. Skin breakdown in that area was observed 2 months later, and the wound continued to increase in size and depth. The patient died shortly thereafter due to complications of cancer. In this case study, a series of infrared images of foot skin temperatures appeared to show a relationship with blood circulation and wound/ulcer development and presentation. IRT has the ability to instantaneously measure the absolute temperature of the skin surface over a large area without direct skin contact. However, the devices are very sensitive and prospective

  10. Infrared thermography videos of the elastocaloric effect for shape memory alloys NiTi and Ni2FeGa

    PubMed Central

    Pataky, Garrett J.; Ertekin, Elif; Sehitoglu, Huseyin

    2015-01-01

    Infrared thermogrpahy was utilized to record the temperature change during tensile loading cycles of two shape memory alloy single crystals with pseudoelastic behavior. During unloading, a giant temperature drop was measured in the gage section due to the elastocaloric effect. This data article provides a video of a [001] oriented Ni2FeGa single crystal, including the corresponding stress–strain curve, shows the temperature drop over one cycle. The second video of a [148] oriented NiTi single crystal depicts the repeatability of the elastocaloric effect by showing two consecutive cycles. The videos are supplied in this paper. For further analysis and enhanced discussion of large temperature change in shape memory alloys, see Pataky et al. [1] PMID:26380838

  11. Infrared thermography videos of the elastocaloric effect for shape memory alloys NiTi and Ni2FeGa.

    PubMed

    Pataky, Garrett J; Ertekin, Elif; Sehitoglu, Huseyin

    2015-12-01

    Infrared thermogrpahy was utilized to record the temperature change during tensile loading cycles of two shape memory alloy single crystals with pseudoelastic behavior. During unloading, a giant temperature drop was measured in the gage section due to the elastocaloric effect. This data article provides a video of a [001] oriented Ni2FeGa single crystal, including the corresponding stress-strain curve, shows the temperature drop over one cycle. The second video of a [148] oriented NiTi single crystal depicts the repeatability of the elastocaloric effect by showing two consecutive cycles. The videos are supplied in this paper. For further analysis and enhanced discussion of large temperature change in shape memory alloys, see Pataky et al. [1].

  12. A Case Study Of Applying Infrared Thermography To Identify A Coolant Leak In A Municipal Ice Skating Rink

    NASA Astrophysics Data System (ADS)

    Wallace, Jay R.

    1989-03-01

    This paper deals with the application of infrared imaging radiometry as a diagnostic inspection tool for locating a concealed leak in the refrigeration system supplying glycol coolant to the arena floor of an ice skating rink in a municipal coliseum facility. Scanning approximately 10 miles of black iron tubing embedded in the arena floor resulted in locating a leak within the supply/return side of the system. A secondary disclosure was a restriction to normal coolant flow in some delivery loops caused by sludge build-up. Specific inspection procedures were established to enhance temperature differentials suitable for good thermal imaging. One procedure utilized the temperature and pressure of the city water supply; a second the availability of 130F hot water from the facility's boiler system; and a third the building's own internal ambient temperature. Destructive testing and other data collection equipment confirmed the thermographic findings revealing a section of corrosion damaged pipe. Repair and flushing of the system was quickly completed with a minimum of construction costs and inconvenience. No financial losses were incurred due to the interruption of scheduled revenue events. Probable cause for the shutdown condition was attributed to a flawed installation decision made 15 years earlier during the initial construction stage.

  13. A systematic review of elastography, electrical impedance scanning, and digital infrared thermography for breast cancer screening and diagnosis.

    PubMed

    Vreugdenburg, Thomas D; Willis, Cameron D; Mundy, Linda; Hiller, Janet E

    2013-02-01

    The objective of this study aimed to systematically identify and evaluate all the available evidence of safety, effectiveness and diagnostic accuracy for three emerging classes of technology promoted for breast cancer screening and diagnosis: Digital infrared thermal imaging (DITI), electrical impedance scanning (EIS) and elastography. A systematic search of seven biomedical databases (EMBASE, PubMed, Web of Science, CRD, CINAHL, Cochrane Library, Current Contents Connect) was conducted through March 2011, along with a manual search of reference lists from relevant studies. The principal outcome measures were safety, effectiveness, and diagnostic accuracy. Data were extracted using a standardised form, and validated for accuracy by the secondary authors. Study quality was appraised using the quality assessment of diagnostic accuracy studies tool, while heterogeneity was assessed using forest plots, Cooks' distance and standardised residual scatter plots, and I (2) statistics. From 6,808 search results, 267 full-text articles were assessed, of which 60 satisfied the inclusion criteria. No effectiveness studies were identified. Only one EIS screening accuracy study was identified, while all other studies involved symptomatic populations. Significant heterogeneity was present among all device classes, limiting the potential for meta-analyses. Sensitivity and specificity varied greatly for DITI (Sens 0.25-0.97, Spec 0.12-0.85), EIS (Sens 0.26-0.98, Spec 0.08-0.81) and ultrasound elastography (Sens 0.35-1.00, Spec 0.21-0.99). It is concluded that there is currently insufficient evidence to recommend the use of these technologies for breast cancer screening. Moreover, the high level of heterogeneity among studies of symptomatic women limits inferences that may be drawn regarding their use as diagnostic tools. Future research employing standardised imaging, research and reporting methods is required.

  14. A novel method to prevent secondary exposure of medical and rescue personnel to toxic materials under biochemical hazard conditions using microwave radar and infrared thermography.

    PubMed

    Matsui, Takemi; Hagisawa, Kousuke; Ishizuka, Toshiaki; Takase, Bonpei; Ishihara, Masayuki; Kikuchi, Makoto

    2004-12-01

    In order to prevent secondary exposure of medical personnel to toxic materials under biochemical hazard conditions, we performed a noncontact determination of exposure to toxic conditions via 1215-MHz microwave radar and thermography. A toxic condition was induced by intravenous administration of lipopolysaccharide (LPS) in rabbits. The exposure to LPS was determined by linear discriminant analysis using non-contact derived variables.

  15. The use of high-resolution infrared thermography (HRIT) for the study of ice nucleation and ice propagation in plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Freezing events that occur when plants are actively growing can be a lethal event particularly if the plant has no freezing tolerance. Such frost events often have devastating effects on agricultural production and can also play an important role in shaping community structure in natural population...

  16. Mid-infrared thermal imaging for an effective mapping of surface materials and sub-surface detachments in mural paintings: integration of thermography and thermal quasi-reflectography

    NASA Astrophysics Data System (ADS)

    Daffara, C.; Parisotto, S.; Mariotti, P. I.

    2015-06-01

    Cultural Heritage is discovering how precious is thermal analysis as a tool to improve the restoration, thanks to its ability to inspect hidden details. In this work a novel dual mode imaging approach, based on the integration of thermography and thermal quasi-reflectography (TQR) in the mid-IR is demonstrated for an effective mapping of surface materials and of sub-surface detachments in mural painting. The tool was validated through a unique application: the "Monocromo" by Leonardo da Vinci in Italy. The dual mode acquisition provided two spatially aligned dataset: the TQR image and the thermal sequence. Main steps of the workflow included: 1) TQR analysis to map surface features and 2) to estimate the emissivity; 3) projection of the TQR frame on reference orthophoto and TQR mosaicking; 4) thermography analysis to map detachments; 5) use TQR to solve spatial referencing and mosaicking for the thermal-processed frames. Referencing of thermal images in the visible is a difficult aspect of the thermography technique that the dual mode approach allows to solve in effective way. We finally obtained the TQR and the thermal maps spatially referenced to the mural painting, thus providing the restorer a valuable tool for the restoration of the detachments.

  17. Development of a rapid soil water content detection technique using active infrared thermal methods for in-field applications.

    PubMed

    Antonucci, Francesca; Pallottino, Federico; Costa, Corrado; Rimatori, Valentina; Giorgi, Stefano; Papetti, Patrizia; Menesatti, Paolo

    2011-01-01

    The aim of this study was to investigate the suitability of active infrared thermography and thermometry in combination with multivariate statistical partial least squares analysis as rapid soil water content detection techniques both in the laboratory and the field. Such techniques allow fast soil water content measurements helpful in both agricultural and environmental fields. These techniques, based on the theory of heat dissipation, were tested by directly measuring temperature dynamic variation of samples after heating. For the assessment of temperature dynamic variations data were collected during three intervals (3, 6 and 10 s). To account for the presence of specific heats differences between water and soil, the analyses were regulated using slopes to linearly describe their trends. For all analyses, the best model was achieved for a 10 s slope. Three different approaches were considered, two in the laboratory and one in the field. The first laboratory-based one was centred on active infrared thermography, considered measurement of temperature variation as independent variable and reported r = 0.74. The second laboratory-based one was focused on active infrared thermometry, added irradiation as independent variable and reported r = 0.76. The in-field experiment was performed by active infrared thermometry, heating bare soil by solar irradiance after exposure due to primary tillage. Some meteorological parameters were inserted as independent variables in the prediction model, which presented r = 0.61. In order to obtain more general and wide estimations in-field a Partial Least Squares Discriminant Analysis on three classes of percentage of soil water content was performed obtaining a high correct classification in the test (88.89%). The prediction error values were lower in the field with respect to laboratory analyses. Both techniques could be used in conjunction with a Geographic Information System for obtaining detailed information on soil heterogeneity.

  18. Air-coupled acoustic thermography for in-situ evaluation

    NASA Technical Reports Server (NTRS)

    Zalameda, Joseph N. (Inventor); Winfree, William P. (Inventor); Yost, William T. (Inventor)

    2010-01-01

    Acoustic thermography uses a housing configured for thermal, acoustic and infrared radiation shielding. For in-situ applications, the housing has an open side adapted to be sealingly coupled to a surface region of a structure such that an enclosed chamber filled with air is defined. One or more acoustic sources are positioned to direct acoustic waves through the air in the enclosed chamber and towards the surface region. To activate and control each acoustic source, a pulsed signal is applied thereto. An infrared imager focused on the surface region detects a thermal image of the surface region. A data capture device records the thermal image in synchronicity with each pulse of the pulsed signal such that a time series of thermal images is generated. For enhanced sensitivity and/or repeatability, sound and/or vibrations at the surface region can be used in feedback control of the pulsed signal applied to the acoustic sources.

  19. Development Of Economic Techniques For Residential Thermography

    NASA Astrophysics Data System (ADS)

    Allen, Lee R.; Allen, Sharon

    1983-03-01

    Infrared thermography has proven to be a valuable tool in the detection of heat loss in both commercial and residential buildings. The field of residential thermography has needed a simple method with which to report the deficiencies found during an infrared scan. Two major obstacles hindering the cost effectiveness of residential thermography have been 1) the ability to quickly transport some high resolution imaging system equipment from job site to job site without having to totally dismount the instruments at each area, and 2) the lack of a standard form with which to report the findings of the survey to the customer. Since the industry has yet to provide us with either, we believed it necessary to develop our own. Through trial and error, we have come up with a system that makes interior residential thermography a profitable venture at a price the homeowner can afford. Insulation voids, or defects can be instantly spotted with the use of a thermal imaging system under the proper conditions. A special hand-held device was developed that enables the thermographer to carry the equipment from house to house without the need to dismantle and set up at each stop. All the necessary components are attached for a total weight of about 40 pounds. The findings are then conveyed to a form we have developed. The form is simple enough that the client without special training in thermography can understand. The client is then able to locate the problems and take corrective measures or give it to a con-tractor to do the work.

  20. Airborne thermography of temperature patterns in sugar beet piles

    NASA Technical Reports Server (NTRS)

    Moore, D. G.; Bichsel, S.

    1975-01-01

    An investigation was conducted to evaluate the use of thermography for locating spoilage areas (chimneys) within storage piles and to subsequently use the information for the scheduling of their processing. Thermal-infrared quantitative scanner data were acquired initially on January 16, 1975, over the storage piles at Moorhead, Minnesota, both during the day and predawn. Photographic data were acquired during the day mission to evaluate the effect of uneven snow cover on the thermal emittance, and the predawn thermography was used to locate potential chimneys. The piles were examined the day prior for indications of spoilage areas, and the ground crew indicated that no spoilage areas were located using their existing methods. Nine spoilage areas were interpreted from the thermography. The piles were rechecked by ground methods three days following the flights. Six of the nine areas delineated by thermography were actual spoilage areas.

  1. NDT of railway components using induction thermography

    NASA Astrophysics Data System (ADS)

    Netzelmann, U.; Walle, G.; Ehlen, A.; Lugin, S.; Finckbohner, M.; Bessert, S.

    2016-02-01

    Induction or eddy current thermography is used to detect surface cracks in ferritic steel. The technique is applied to detect surface cracks in rails from a moving test car. Cracks were detected at a train speed between 2 and 15 km/h. An automated demonstrator system for testing railway wheels after production is described. While the wheel is rotated, a robot guides the detection unit consisting of inductor and infrared camera over the surface.

  2. Potential applications of ocular thermography.

    PubMed

    Morgan, P B; Soh, M P; Efron, N; Tullo, A B

    1993-07-01

    Thermography is an investigative technique which allows rapid color-coded display of the temperature across a wide surface by means of infrared detection. We describe an ocular thermographic study of a normal population and present case studies describing the application of this technique for patients with ocular disease. We found that 95% of the normal population have an interocular temperature difference (temperature of center of right cornea minus temperature of center of left cornea) of 0.60 degrees or less. There appears to be a greater difference in temperature between the limbus and the center of the cornea in patients with dry eyes. This technique has potential for evaluating tear film disorders and inflammatory conditions, for monitoring the progress of such conditions, and for evaluating the efficacy of various treatments.

  3. 3D thermography imaging standardization technique for inflammation diagnosis

    NASA Astrophysics Data System (ADS)

    Ju, Xiangyang; Nebel, Jean-Christophe; Siebert, J. Paul

    2005-01-01

    We develop a 3D thermography imaging standardization technique to allow quantitative data analysis. Medical Digital Infrared Thermal Imaging is very sensitive and reliable mean of graphically mapping and display skin surface temperature. It allows doctors to visualise in colour and quantify temperature changes in skin surface. The spectrum of colours indicates both hot and cold responses which may co-exist if the pain associate with an inflammatory focus excites an increase in sympathetic activity. However, due to thermograph provides only qualitative diagnosis information, it has not gained acceptance in the medical and veterinary communities as a necessary or effective tool in inflammation and tumor detection. Here, our technique is based on the combination of visual 3D imaging technique and thermal imaging technique, which maps the 2D thermography images on to 3D anatomical model. Then we rectify the 3D thermogram into a view independent thermogram and conform it a standard shape template. The combination of these imaging facilities allows the generation of combined 3D and thermal data from which thermal signatures can be quantified.

  4. Clinical applications of computerized thermography

    NASA Technical Reports Server (NTRS)

    Anbar, Michael

    1988-01-01

    Computerized or digital, thermography is a rapidly growing diagnostic imaging modality. It has superseded contact thermography and analog imaging thermography which do not allow effective quantization. Medical applications of digital thermography can be classified in two groups: static and dynamic imaging. They can also be classified into macro thermography (resolution greater than 1 mm) and micro thermography (resolution less than 100 microns). Both modalities allow a thermal resolution of 0.1 C. The diagnostic power of images produced by any of these modalities can be augmented by the use of digital image enhancement and image recognition procedures. Computerized thermography has been applied in neurology, cardiovascular and plastic surgery, rehabilitation and sports medicine, psychiatry, dermatology and ophthalmology. Examples of these applications are shown and their scope and limitations are discussed.

  5. Bonding quality evaluation of wind turbine blades by pulsed thermography

    NASA Astrophysics Data System (ADS)

    He, Rui-gang; Kong, De-juan; Zeng, Zhi; Tao, Ning; Zhang, Cun-lin; Feng, Li-chun

    2011-08-01

    The glue defects of the wind turbine blades which are composed of the glass fiber reinforced plastic (GFRP) composite plates make its strength greatly reduced, so security issues could be caused. To improve the safety of wind turbine blades, nondestructive testing technique using pulsed thermography is being investigated in this study. The results of ultrasonic C scan test were compared with the results of thermography. The current results indicated that both methods can successfully detect two gluing situations. However, the inspect specimens need to be putted in the water in the detection process by ultrasonic C scan, and the detection time lasts much longer than pulsed thermography. And in situ applications, the measured wind turbine blades are normally in the size of several tens meter, and also only one side is available for the inspection especially at the tip of blades. Thus, ultrasonic C scan of current experimental setup is not suitable for the applications in the field. Pulsed thermography is not necessary to contact with inspected specimens. The infrared results by pulsed thermography indicate that the shape and size of deficiency glue defects in the specimens show good agreement with the real situation, so it is more suitable for the inspection in the field. The preliminary results in this study indicate that pulse thermography can be used to detect glue faults of GFRP which are not too thick.

  6. Applying Active Thermography in the Non-Destructive Investigation of Historical Objects/ Zastosowanie Termowizji Aktywnej Do Badań Nieniszczących Obiektów Zabytkowych

    NASA Astrophysics Data System (ADS)

    Nowak, Henryk; Noszczyk, Paweł

    2015-06-01

    The paper pertains to the problem of historic building envelope investigation with the use of active thermography. Mainly emphasized is its application in the detection of different material inclusions in historic walls. Examples of active thermography in the reflective mode application and a description of the experimental investigation has been shown on a wall model with the inclusion of materials with significantly different thermal conductivity and heat capacity, i.e. styrofoam, steel and granite. Thermograms received for every kind of envelope are compared and analyzed. Finally, the summary and conclusion is shown along with the prospects of development and practical application of this kind of investigation in historic construction. Artykuł porusza zagadnienie wykorzystania termografii aktywnej w nieniszczących badaniach przegród budowlanych w obiektach zabytkowych. Opisane zostały potencjalne możliwości stosowania badań, takie jak: lokalizacja rodzaju zbrojenia w elementach żelbetowych, detekcja pustek powietrznych i przemurowań w przegrodach, określanie rodzaju struktury materiałowej zabytkowej przegrody lub identyfikacja ukrytych pod wartwą tynku lub farby malowideł ściennych. W pracy opisano przebieg doświadczenia z wykorzystaniem termografii aktywnej w trybie odbiciowym. W badanych modelach przegród, wewnętrzne wtrącenia materiałowe zostały wykonane ze styropianu XPS, stali oraz granitu. Otrzymane wyniki opisano za pomocą kontrastów temperaturowych (absolutny i standardowy) oraz zinterptretowano otrzymane termogramy. W podsumowaniu przedstawiono wnioski z przeprowadzonego doświadczenia. W artykule potwierdzono przydatność nieniszczących badań za pomocą termowizji aktywnej do detekcji przypowierzchniowych wtrąceń materiałowych.

  7. Development of nondestructive crack inspection technique for conveyance roll using vibro-thermography

    NASA Astrophysics Data System (ADS)

    Imanishi, Daisuke; Nishina, Yoshiaki; Yoshinaga, Youichi

    2012-06-01

    In recent study, active thermography has reached a high status as an easy and speedy defects inspection method in a NDT field. This paper newly proposes a non-disassembly and non-contact NDT method using the Vibro-Thermography for detecting and evaluating of fatigue cracks at neck parts of the conveyance roll in the steel making plant. In this method, fatigue cracks are detected as localized high temperature areas caused by friction and impact at crack surfaces with an infrared thermography, applying a high-amplitude ultrasonic vibration. In the case of the roll surface is covered with lubricating grease or dust, the crack detectability is shown. Self reference lock-in data processing technique is applied for improvement of signal noise ratio in the crack detection process. This technique makes it possible to perform correlating process without an external reference signal. Time and cost saving inspection method in the neck part of conveyance roll is carried out using this NDT technique.

  8. Defect Detection in Composite Coatings by Computational Simulation Aided Thermography

    NASA Astrophysics Data System (ADS)

    Almeida, R. M.; Souza, M. P. V.; Rebello, J. M. A.

    2010-02-01

    Thermography is based on the measurement of superficial temperature distribution of an object inspected subjected to tension, normally thermal heat. This measurement is performed with a thermographic camera that detects the infrared radiation emitted by every object. In this work thermograph was simulated by COMSOL software for optimize experimental parameters in composite material coatings inspection.

  9. Abnormal Activity Detection Using Pyroelectric Infrared Sensors.

    PubMed

    Luo, Xiaomu; Tan, Huoyuan; Guan, Qiuju; Liu, Tong; Zhuo, Hankz Hankui; Shen, Baihua

    2016-06-03

    Healthy aging is one of the most important social issues. In this paper, we propose a method for abnormal activity detection without any manual labeling of the training samples. By leveraging the Field of View (FOV) modulation, the spatio-temporal characteristic of human activity is encoded into low-dimension data stream generated by the ceiling-mounted Pyroelectric Infrared (PIR) sensors. The similarity between normal training samples are measured based on Kullback-Leibler (KL) divergence of each pair of them. The natural clustering of normal activities is discovered through a self-tuning spectral clustering algorithm with unsupervised model selection on the eigenvectors of a modified similarity matrix. Hidden Markov Models (HMMs) are employed to model each cluster of normal activities and form feature vectors. One-Class Support Vector Machines (OSVMs) are used to profile the normal activities and detect abnormal activities. To validate the efficacy of our method, we conducted experiments in real indoor environments. The encouraging results show that our method is able to detect abnormal activities given only the normal training samples, which aims to avoid the laborious and inconsistent data labeling process.

  10. Abnormal Activity Detection Using Pyroelectric Infrared Sensors

    PubMed Central

    Luo, Xiaomu; Tan, Huoyuan; Guan, Qiuju; Liu, Tong; Zhuo, Hankz Hankui; Shen, Baihua

    2016-01-01

    Healthy aging is one of the most important social issues. In this paper, we propose a method for abnormal activity detection without any manual labeling of the training samples. By leveraging the Field of View (FOV) modulation, the spatio-temporal characteristic of human activity is encoded into low-dimension data stream generated by the ceiling-mounted Pyroelectric Infrared (PIR) sensors. The similarity between normal training samples are measured based on Kullback-Leibler (KL) divergence of each pair of them. The natural clustering of normal activities is discovered through a self-tuning spectral clustering algorithm with unsupervised model selection on the eigenvectors of a modified similarity matrix. Hidden Markov Models (HMMs) are employed to model each cluster of normal activities and form feature vectors. One-Class Support Vector Machines (OSVMs) are used to profile the normal activities and detect abnormal activities. To validate the efficacy of our method, we conducted experiments in real indoor environments. The encouraging results show that our method is able to detect abnormal activities given only the normal training samples, which aims to avoid the laborious and inconsistent data labeling process. PMID:27271632

  11. Using thermography for an obstruction of the lower lacrimal system.

    PubMed

    Machado, Marco Antonio de Campos; Silva, João Amaro Ferrari; Brioschi, Marcos Leal; Allemann, Norma

    2016-02-01

    Obstructions in the lacrimal pathways quite often require accurate and reliable image scanning for confirmation and documentation. Infrared thermal imaging, known as thermography, is a resource that complements diagnosis; it does not require touching the patient or applying contrast materials and has been used in various medical procedures for decades. However, there have been few studies in the literature about its use in ophthalmology. In this paper, the authors have presented a case of dacryocystitis where the obstruction of the lacrimal punctum was so acute that conventional dacryocystography could not be used. The authors have successfully reported the use of thermography as a complementary propaedeutic and will discuss the method they used.

  12. Computer Assisted Thermography And Its Application In Ovulation Detection

    NASA Astrophysics Data System (ADS)

    Rao, K. H.; Shah, A. V.

    1984-08-01

    Hardware and software of a computer-assisted image analyzing system used for infrared images in medical applications are discussed. The application of computer-assisted thermography (CAT) as a complementary diagnostic tool in centralized diagnostic management is proposed. The authors adopted 'Computer Assisted Thermography' to study physiological changes in the breasts related to the hormones characterizing the menstrual cycle of a woman. Based on clinical experi-ments followed by thermal image analysis, they suggest that 'differential skin temperature (DST)1 be measured to detect the fertility interval in the menstrual cycle of a woman.

  13. Infrared

    NASA Astrophysics Data System (ADS)

    Vollmer, M.

    2013-11-01

    techniques such as attenuated total reflectance [6]. The two final papers deal with what seem to be wholly different scientific fields [7, 8]. One paper describes SOFIA, an aeroplane-based astronomical observatory covering the whole IR range [7], while the other represents a small review of the quite new topic of terahertz physics at the upper end of the IR spectral range, from around 30 µm to 3 mm wavelength, and its many applications in science and industry [8]. Although artificially separated, all these fields use similar kinds of detectors, similar kinds of IR sources and similar technologies, while the instruments use the same physical principles. We are convinced that the field of infrared physics will develop over the next decade in the same dynamic way as during the last, and this special issue may serve as starting point for regular submissions on the topic. At any rate, it shines a light on this fascinating and many-faceted subject, which started more than 200 years ago. References [1] Mangold K, Shaw J A and Vollmer M 2013 The physics of near-infrared photography Eur. J. Phys. 34 S51-71 [2] Vollmer M and Möllmann K-P 2013 Characterization of IR cameras in student labs Eur. J. Phys. 34 S73-90 [3] Ibarra-Castanedo C, Tarpani J R and Maldague X P V 2013 Nondestructive testing with thermography Eur. J. Phys. 34 S91-109 [4] Shaw J A and Nugent P W 2013 Physics principles in radiometric infrared imaging of clouds in the atmosphere Eur. J. Phys. 34 S111-21 [5] Möllmann K-P and Vollmer M 2013 Fourier transform infrared spectroscopy in physics laboratory courses Eur. J. Phys. 34 S123-37 [6] Heise H M, Fritzsche J, Tkatsch H, Waag F, Karch K, Henze K, Delbeck S and Budde J 2013 Recent advances in mid- and near-infrared spectroscopy with applications for research and teaching, focusing on petrochemistry and biotechnology relevant products Eur. J. Phys. 34 S139-59 [7] Krabbe A, Mehlert D, Röser H-P and Scorza C 2013 SOFIA, an airborne observatory for infrared astronomy

  14. Breast cancer detection in rotational thermography images using texture features

    NASA Astrophysics Data System (ADS)

    Francis, Sheeja V.; Sasikala, M.; Bhavani Bharathi, G.; Jaipurkar, Sandeep D.

    2014-11-01

    Breast cancer is a major cause of mortality in young women in the developing countries. Early diagnosis is the key to improve survival rate in cancer patients. Breast thermography is a diagnostic procedure that non-invasively images the infrared emissions from breast surface to aid in the early detection of breast cancer. Due to limitations in imaging protocol, abnormality detection by conventional breast thermography, is often a challenging task. Rotational thermography is a novel technique developed in order to overcome the limitations of conventional breast thermography. This paper evaluates this technique's potential for automatic detection of breast abnormality, from the perspective of cold challenge. Texture features are extracted in the spatial domain, from rotational thermogram series, prior to and post the application of cold challenge. These features are fed to a support vector machine for automatic classification of normal and malignant breasts, resulting in a classification accuracy of 83.3%. Feature reduction has been performed by principal component analysis. As a novel attempt, the ability of this technique to locate the abnormality has been studied. The results of the study indicate that rotational thermography holds great potential as a screening tool for breast cancer detection.

  15. Skin vasomotor hemiparesis followed by overactivity: characteristic thermography findings in a patient with Horner syndrome due to spinal cord infarction.

    PubMed

    Kobayashi, Makoto

    2016-04-01

    We present a 21-year-old female with Horner syndrome due to spinal cord infarction. In this patient, infrared thermography revealed a hemibody skin temperature increase followed by excessive focal decreases, indicating skin vasomotor hemiparesis and overactivity.

  16. Investigation on choosing technical parameters for pulse thermography

    NASA Astrophysics Data System (ADS)

    Li, Huijuan

    2015-04-01

    Composite material connected by glue has gained popularity as a replacement for conventional materials and structures to reduce weight and improve strength in the aerospace industry, with the development of material science and structural mechanics. However, the adhesive bonding process is more susceptible to quality variations during manufacturing than traditional joining methods. The integrality, strength and rigidity of product would be broken by disbonding. Infrared thermography is one of several non-destructive testing techniques which can be used for defect detection in aircraft materials. Pulsed infrared thermography has been widely used in aerospace and mechanical manufacture industry because it can offer noncontact, quickly and visual examinations of disbonding defects. However the parameter choosing method is difficult to decide. Investigate the choosing technical parameters for pulse thermograpghy is more important to ensure the product quality and testing efficiency. In this paper, two kinds of defects which are of various size, shape and location below the test surface are planted in the honeycomb structure, they are all tested by pulsed thermography. This paper presents a study of single factor experimental research on damage sample in simulation was carried out. The impact of the power of light source, detection distance, and the wave band of thermography camera on detecting effect is studied. The select principle of technique is made, the principle supplied basis for selection of detecting parameters in real part testing.

  17. The Use of Infrared Thermography as a Rapid, Quantitative, and Noninvasive Method for Evaluation of Inflammation Response in Different Anatomical Regions of Rats

    PubMed Central

    Całkosiński, Ireneusz; Dobrzyński, Maciej; Rosińczuk, Joanna; Dudek, Krzysztof; Chrószcz, Aleksander; Fita, Katarzyna

    2015-01-01

    Purpose. Thermographic assessment of temperature distribution within the examined tissues allows a quick, noncontact, noninvasive measurement of their temperature. The aim of the study was to evaluate the usefulness of digital infrared imaging in monitoring experimental inflammation of pleura (PL), lower lip (LL), and left paw (LP) and right paw (RP) of lower limbs in rats. Materials and Methods. The inflammatory reaction was induced by injection of 1% carrageenin solution into pleural cavity, lip, or paws. With the use of digital infrared imaging temperature measurement was conducted at 0 to 72 hours of the inflammatory reaction. Results. The temperature decrease was observed at the site of injection directly afterwards. Next, it was gradually increasing and it reached the maximum on the third day of the inflammatory reaction. Statistically significant changes were observed after 48-hour period in PL and LL regions, as well as after 72-hour period in LP and RP regions (P < 0.005). Conclusion. It was found that thermographic examination allows for indicating the presence of inflammatory reaction within examined tissues and determining the dynamics of this process. This method could be used as alternative procedure that allows using fewer animals for experiments. PMID:25834830

  18. Infrared thermography and meridian-effect evidence and explanation in Bell's palsy patients treated by moxibustion at the Hegu (LI4) acupoint

    PubMed Central

    Guan, Ling; Li, Gaobo; Yang, Yiling; Deng, Xiufang; Cai, Peisi

    2012-01-01

    Subjects with Bell's palsy and healthy individuals were treated with moxibustion thermal stimulation on the Hegu (LI4) acupoint; an infrared thermal imaging system was used to observe facial-temperature changes. Bell's palsy patients developed low or high temperatures at the affected side, with poor symmetry. Healthy people showed high temperatures on the forehead, medial angle of the eye, nasal ala and around the lips, but low temperatures on bilateral cheeks, thus forming a “T-type hot area” in the face, with good temperature symmetry. Moxibustion treatment for 11 minutes significantly improved high asymmetry in temperature in the faces of Bell's palsy patients. This evidence indicates that moxibustion treatment on Hegu enables increases in facial temperatures in healthy people and Bell's palsy patients, especially around the lips. Moxibustion stimulation at the Hegu not only improves the global circulation but also has specific effects on the lips in Bell's palsy patients, but the underlying mechanism needs further investigation. PMID:25745463

  19. Inquiry-based Science Activities Using The Infrared Zoo and Infrared Yellowstone Resources at Cool Cosmos

    NASA Astrophysics Data System (ADS)

    Daou, D.; Gauthier, A.

    2003-12-01

    Inquiry-based activities that utilize the Cool Cosmos image galleries have been designed and developed by K12 teachers enrolled in The Invisible Universe Online for Teachers course. The exploration activities integrate the Our Infrared World Gallery (http://coolcosmos.ipac.caltech.edu/image_galleries/our_ir_world_gallery.html) with either the Infrared Zoo gallery (http://coolcosmos.ipac.caltech.edu/image_galleries/ir_zoo/index.html) or the Infrared Yellowstone image http://coolcosmos.ipac.caltech.edu/image_galleries/ir_yellowstone/index.html) and video (http://coolcosmos.ipac.caltech.edu/videos/ir_yellowstone/index.html) galleries. Complete instructor guides have been developed for the activities and will be presented by the authors in poster and CD form. Although the activities are written for middle and highschool learners, they can easily be adapted for college audiences. The Our Infrared World Gallery exploration helps learners think critically about visible light and infrared light as they compare sets of images (IR and visible light) of known objects. For example: by taking a regular photograph of a running faucet, can you tell if it is running hot or cold water? What new information does the IR image give you? The Infrared Zoo activities encourage learners to investigate the differences between warm and cold blooded animals by comparing sets of IR and visible images. In one activity, learners take on the role of a pit viper seeking prey in various desert and woodland settings. The main activities are extended into the real world by discussing and researching industrial, medical, and societal applications of infrared technologies. The Infrared Yellowstone lessons give learners a unique perspective on Yellowstone National Park and it's spectacular geologic and geothermal features. Infrared video technology is highlighted as learners make detailed observations about the visible and infrared views of the natural phenomena. The "Cool Cosmos" EPO activities are

  20. Activities of the CLIO infrared facility

    SciTech Connect

    Ortega, J.M.; Berset, J.M.; Chaput, R.

    1995-12-31

    The CLIO infrared FEL is operated since 1992. It is based on a 3 GHz RF linac. The laser beam time was about 2400 h in 1994, 1600 for users and 800 for FEL physics and machine optimisation. The beam time is limited mainly by user ability to work during nights.

  1. Roles For Thermography In Utility Company Residential Energy Audits

    NASA Astrophysics Data System (ADS)

    Schott, William A.

    1981-01-01

    Basin Electric Power Cooperative, Bismarck, North Dakota, provides wholesale electricity to more than 100 rural electric cooperatives of the Missouri Pasin Region. The Cooperative, in cooperation with Aadland*Hoffmann*Pieri Energy Associates, Inc., Minneapolis, MN has developed a three-fold program which involves the analytical approach, the instructional approach and the motivational approach (A'IsM) to an energy audit. This three-fold program utilizes infrared thermography to pinpoint where heat loss is occurring in the home. The auditor can motivate the homeowner to initiate energy conserving improvements and practices by showing where money can be saved. Infrared thermography is a most valuable tool in helping the rural electrics conserve energy and the nation's natural resources. Over 180 energy auditors have been trained through this program in this area and 5,000 trained in the nation.

  2. Infrared Detector Activities at NASA Langley Research Center

    NASA Technical Reports Server (NTRS)

    Abedin, M. N.; Refaat, T. F.; Sulima, O. V.; Amzajerdian, F.

    2008-01-01

    Infrared detector development and characterization at NASA Langley Research Center will be reviewed. These detectors were intended for ground, airborne, and space borne remote sensing applications. Discussion will be focused on recently developed single-element infrared detector and future development of near-infrared focal plane arrays (FPA). The FPA will be applied to next generation space-based instruments. These activities are based on phototransistor and avalanche photodiode technologies, which offer high internal gain and relatively low noise-equivalent-power. These novel devices will improve the sensitivity of active remote sensing instruments while eliminating the need for a high power laser transmitter.

  3. Improvement of wound healing by water-filtered infrared-A (wIRA) in patients with chronic venous stasis ulcers of the lower legs including evaluation using infrared thermography

    PubMed Central

    Mercer, James B.; Nielsen, Stig Pors; Hoffmann, Gerd

    2008-01-01

    Background: Water-filtered infrared-A (wIRA) is a special form of heat radiation with a high tissue-penetration and with a low thermal burden to the surface of the skin. wIRA is able to improve essential and energetically meaningful factors of wound healing by thermal and non-thermal effects. Aim of the study: prospective study (primarily planned randomised, controlled, blinded, de facto with one exception only one cohort possible) using wIRA in the treatment of patients with recalcitrant chronic venous stasis ulcers of the lower legs with thermographic follow-up. Methods: 10 patients (5 males, 5 females, median age 62 years) with 11 recalcitrant chronic venous stasis ulcers of the lower legs were treated with water-filtered infrared-A and visible light irradiation (wIRA(+VIS), Hydrosun® radiator type 501, 10 mm water cuvette, water-filtered spectrum 550–1400 nm) or visible light irradiation (VIS; only possible in one patient). The uncovered wounds of the patients were irradiated two to five times per week for 30 minutes at a standard distance of 25 cm (approximately 140 mW/cm2 wIRA and approximately 45 mW/cm2 VIS). Treatment continued for a period of up to 2 months (typically until closure or nearly closure of the ulcer). The main variable of interest was “percent change of ulcer size over time” including complete wound closure. Additional variables of interest were thermographic image analysis, patient’s feeling of pain in the wound, amount of pain medication, assessment of the effect of the irradiation (by patient and by clinical investigator), assessment of feeling of the wound area (by patient), assessment of wound healing (by clinical investigator) and assessment of the cosmetic state (by patient and by clinical investigator). For these assessments visual analogue scales (VAS) were used. Results: The study showed a complete or nearly complete healing of lower leg ulcers in 7 patients and a clear reduction of ulcer size in another 2 of 10 patients, a

  4. Infrared Emission from the Smallest Active Galaxies

    NASA Astrophysics Data System (ADS)

    Barth, Aaron; Greene, Jenny; Ho, Luis

    2006-05-01

    Virtually all of our current knowledge of black hole demographics, both in nearby inactive galaxies and in AGNs, comes from observations of black holes with masses between a few million and a few billion solar masses in host galaxies with stellar velocity dispersions between about 70 and 400 km/sec. Searching for smaller black holes in low-mass galaxies can yield important clues to the origin and early evolution of supermassive black holes, and AGN surveys are the best available way to identify such objects. Using the Sloan Digital Sky Survey, we have identified 19 Seyfert 1 galaxies with black hole mass below 10^6 solar masses (Greene & Ho 2004), and 20 Seyfert 2 galaxies having stellar velocity dispersions smaller than 70 km/sec as determined by new Keck observations. These AGN samples offer a unique opportunity to study the very early growth stages of black holes and their host galaxies. Spitzer observations of mid-infrared emission will be the best available calorimeter of the energetics of these tiny AGNs. Our primary goal is to determine the infrared contribution to the bolometric luminosities, which will be a key to understanding the black hole accretion rates. From the infrared spectral shapes we will constrain the dust temperatures and search for silicate features in emission or absorption that may indicate the presence of an obscuring torus, and which will help to determine whether the Type 1 and Type 2 objects differ primarily as a result of our viewing angle, as in classic AGN unified models. PAH features and narrow emission lines will be used to diagnose the relative contributions of AGN and star formation to the infrared luminosity. To accomplish these goals, we request IRS staring-mode spectroscopy in the SL2, SL1, LL2, and LL1 settings for our Sloan-selected sample of 19 Seyfert 1s and 20 Seyfert 2s, as well as NGC 4395 and POX 52, which are the prototypical nearby examples of Seyfert nuclei in dwarf host galaxies.

  5. Motor Neuron Activation in Peripheral Nerves Using Infrared Neural Stimulation

    PubMed Central

    Peterson, EJ; Tyler, DJ

    2014-01-01

    Objective Localized activation of peripheral axons may improve selectivity of peripheral nerve interfaces. Infrared neural stimulation (INS) employs localized delivery to activate neural tissue. This study investigated INS to determine whether localized delivery limited functionality in larger mammalian nerves. Approach The rabbit sciatic nerve was stimulated extraneurally with 1875 nm-wavelength infrared light, electrical stimulation, or a combination of both. Infrared-sensitive regions (ISR) of the nerve surface and electromyogram (EMG) recruitment of the Medial Gastrocnemius, Lateral Gastrocnemius, Soleus, and Tibialis Anterior were the primary output measures. Stimulation applied included infrared-only, electrical-only, and combined infrared and electrical. Main results 81% of nerves tested were sensitive to INS, with 1.7± 0.5 ISR detected per nerve. INS was selective to a single muscle within 81% of identified ISR. Activation energy threshold did not change significantly with stimulus power, but motor activation decreased significantly when radiant power was decreased. Maximum INS levels typically recruited up to 2–9% of any muscle. Combined infrared and electrical stimulation differed significantly from electrical recruitment in 7% of cases. Significance The observed selectivity of INS indicates it may be useful in augmenting rehabilitation, but significant challenges remain in increasing sensitivity and response magnitude to improve the functionality of INS. PMID:24310923

  6. Motor neuron activation in peripheral nerves using infrared neural stimulation

    NASA Astrophysics Data System (ADS)

    Peterson, E. J.; Tyler, D. J.

    2014-02-01

    Objective. Localized activation of peripheral axons may improve selectivity of peripheral nerve interfaces. Infrared neural stimulation (INS) employs localized delivery to activate neural tissue. This study investigated INS to determine whether localized delivery limited functionality in larger mammalian nerves. Approach. The rabbit sciatic nerve was stimulated extraneurally with 1875 nm wavelength infrared light, electrical stimulation, or a combination of both. Infrared-sensitive regions (ISR) of the nerve surface and electromyogram (EMG) recruitment of the Medial Gastrocnemius, Lateral Gastrocnemius, Soleus, and Tibialis Anterior were the primary output measures. Stimulation applied included infrared-only, electrical-only, and combined infrared and electrical. Main results. 81% of nerves tested were sensitive to INS, with 1.7 ± 0.5 ISR detected per nerve. INS was selective to a single muscle within 81% of identified ISR. Activation energy threshold did not change significantly with stimulus power, but motor activation decreased significantly when radiant power was decreased. Maximum INS levels typically recruited up to 2-9% of any muscle. Combined infrared and electrical stimulation differed significantly from electrical recruitment in 7% of cases. Significance. The observed selectivity of INS indicates that it may be useful in augmenting rehabilitation, but significant challenges remain in increasing sensitivity and response magnitude to improve the functionality of INS.

  7. Validity of inner canthus temperature recorded by infrared thermography as a non-invasive surrogate measure for core temperature at rest, during exercise and recovery.

    PubMed

    Fernandes, Alex Andrade; Moreira, Danilo Gomes; Brito, Ciro José; da Silva, Cristiano Diniz; Sillero-Quintana, Manuel; Pimenta, Eduardo Mendonça; Bach, Aaron J E; Garcia, Emerson Silami; Bouzas Marins, João Carlos

    2016-12-01

    Research into obtaining a fast, valid, reliable and non-invasive measure of core temperature is of interest in many disciplinary fields. Occupational and sports medicine research has attempted to determine a non-invasive proxy for core temperature particularly when access to participants is limited and thermal safety is of a concern due to protective encapsulating clothing, hot ambient environments and/or high endogenous heat production during athletic competition. This investigation aimed to determine the validity of inner canthus of the eye temperature (TEC) as an alternate non-invasive measure of intestinal core temperature (TC) during rest, exercise and post-exercise conditions. Twelve physically active males rested for 30min prior to exercise, performed 60min of aerobic exercise at 60% V̇O2max and passively recovered a further 60min post-exercise. TEC and TC were measured at 5min intervals during each condition. Mean differences between TEC and TC were 0.61°C during pre-exercise, -1.78°C during exercise and -1.00°C during post-exercise. The reliability between the methods was low in the pre-exercise (ICC=0.49 [-0.09 to 0.82]), exercise (ICC=-0.14 [-0.65 to 0.44]) and post-exercise (ICC=-0.25 [-0.70 to 0.35]) conditions. In conclusion, poor agreement was observed between the TEC values measured through IRT and TC measured through a gastrointestinal telemetry pill. Therefore, TEC is not a valid substitute measurement to gastrointestinal telemetry pill in sports and exercise science settings.

  8. Principal Components of Thermography analyses of the Silk Tomb, Petra (Jordan)

    NASA Astrophysics Data System (ADS)

    Gomez-Heras, Miguel; Alvarez de Buergo, Monica; Fort, Rafael

    2015-04-01

    This communication presents the results of an active thermography survey of the Silk Tomb, which belongs to the Royal Tombs compound in the archaeological city of Petra in Jordan. The Silk Tomb is carved in the variegated Palaeozoic Umm Ishrin sandstone and it is heavily backweathered due to surface runoff from the top of the cliff where it is carved. Moreover, the name "Silk Tomb" was given because of the colourful display of the variegated sandstone due to backweathering. A series of infrared images were taken as the façade was heated by sunlight to perform a Principal Component of Thermography analyses with IR view 1.7.5 software. This was related to indirect moisture measurements (percentage of Wood Moisture Equivalent) taken across the façade, by means of a Protimeter portable moisture meter. Results show how moisture retention is deeply controlled by lithological differences across the façade. Research funded by Geomateriales 2 S2013/MIT-2914 and CEI Moncloa (UPM, UCM, CSIC) through a PICATA contract and the equipment from RedLAbPAt Network

  9. Integration of infrared and optical imaging techniques for the nondestructive inspection of aeronautic parts

    NASA Astrophysics Data System (ADS)

    López, F.; Sfarra, S.; Ibarra-Castanedo, C.; Paoletti, D.; Maldague, X.

    2015-05-01

    This work focuses in the implementation of infrared and optical imaging techniques for the inspection of aeronautics parts. To this aim, a helicopter blade with known defects is inspected with four different techniques: long pulse thermography, pulsed thermography, digital speckle photography (DSP) and holographic interferometry (HI). The first two techniques belongs to the group of infrared imaging techniques, which are based on the analysis of the infrared thermal patterns in order to detect internal anomalies in the material; whilst the last two (DSP and HI) corresponds to the optical imaging techniques which make use of visible light to measure the material response to an applied stress. Both techniques were applied using the active approach, i.e. an external stimulation is applied in order to produce a gradient in either, the thermal and/or displacement field of the material. The results are then compared in order to evaluate the advantages and limitations of each technique.

  10. Applications of the thermography in the animal production

    NASA Astrophysics Data System (ADS)

    Piñeiro, Carlos; Vizcaino, Elena; Morales, Joaquín.; Manso, Alberto; Díaz, Immaculada; Montalvo, Gema

    2015-04-01

    Infrared thermography is a working technology for over decades, which have been applied mainly in the buildings. We want to move this use to the animal production in order to help us to detect problems of energy efficiency in the facilities preventing, for example, the animal's welfare. In animal production it is necessary to provide a suitable microclimate according to age and production stage of the animals. This microclimate is achieved in the facilities through the environment modification artificially, providing an appropriate comfort for the animals. Many of the problems detected in farms are related to a poor environmental management and control. This is where infrared thermography becomes an essential diagnostic tool to detect failures in the facilities that will be related with health and performance of the animals. The use of this technology in energy audits for buildings, facilities, etc. is becoming more frequent, enabling the technician to easily detect and assess the temperature and energy losses, and it can be used as a support to draft reports and to transmit the situation to the owner in a visual format. In this way, both will be able to decide what improvements are required. Until now, there was not an appropriate technology with affordable prices and easy to manage enough in order to allow the use of the thermography like a routine tool for the diagnostic of these problems, but currently there are some solutions which are starting to appear on the market to meet the requirements needed by the industry.

  11. Potentialities of steady-state and transient thermography in breast tumour depth detection: A numerical study.

    PubMed

    Amri, Amina; Pulko, Susan Helen; Wilkinson, Anthony James

    2016-01-01

    Breast thermography still has inherent limitations that prevent it from being fully accepted as a breast screening modality in medicine. The main challenges of breast thermography are to reduce false positive results and to increase the sensitivity of a thermogram. Further, it is still difficult to obtain information about tumour parameters such as metabolic heat, tumour depth and diameter from a thermogram. However, infrared technology and image processing have advanced significantly and recent clinical studies have shown increased sensitivity of thermography in cancer diagnosis. The aim of this paper is to study numerically the possibilities of extracting information about the tumour depth from steady state thermography and transient thermography after cold stress with no need to use any specific inversion technique. Both methods are based on the numerical solution of Pennes bioheat equation for a simple three-dimensional breast model. The effectiveness of two approaches used for depth detection from steady state thermography is assessed. The effect of breast density on the steady state thermal contrast has also been studied. The use of a cold stress test and the recording of transient contrasts during rewarming were found to be potentially suitable for tumour depth detection during the rewarming process. Sensitivity to parameters such as cold stress temperature and cooling time is investigated using the numerical model and simulation results reveal two prominent depth-related characteristic times which do not strongly depend on the temperature of the cold stress or on the cooling period.

  12. Active infrared materials for beam steering.

    SciTech Connect

    Brener, Igal; Reno, John Louis; Passmore, Brandon Scott; Gin, Aaron V.; Shaner, Eric Arthur; Miao, Xiaoyu; Barrick, Todd A.

    2010-10-01

    The mid-infrared (mid-IR, 3 {micro}m -12 {micro}m) is a highly desirable spectral range for imaging and environmental sensing. We propose to develop a new class of mid-IR devices, based on plasmonic and metamaterial concepts, that are dynamically controlled by tunable semiconductor plasma resonances. It is well known that any material resonance (phonons, excitons, electron plasma) impacts dielectric properties; our primary challenge is to implement the tuning of a semiconductor plasma resonance with a voltage bias. We have demonstrated passive tuning of both plasmonic and metamaterial structures in the mid-IR using semiconductors plasmas. In the mid-IR, semiconductor carrier densities on the order of 5E17cm{sup -3} to 2E18cm{sup -3} are desirable for tuning effects. Gate control of carrier densities at the high end of this range is at or near the limit of what has been demonstrated in literature for transistor style devices. Combined with the fact that we are exploiting the optical properties of the device layers, rather than electrical, we are entering into interesting territory that has not been significantly explored to date.

  13. Thermography in ocular inflammation

    PubMed Central

    Kawali, Ankush A

    2013-01-01

    Background and Objectives: The purpose of this study was to evaluate ocular inflammatory and non-inflammatory conditions using commercially available thermal camera. Materials and Methods: A non-contact thermographic camera (FLIR P 620) was used to take thermal pictures of seven cases of ocular inflammation, two cases of non-inflammatory ocular pathology, and one healthy subject with mild refractive error only. Ocular inflammatory cases included five cases of scleritis, one case of postoperative anterior uveitis, and a case of meibomian gland dysfunction with keratitis (MGD-keratitis). Non-inflammatory conditions included a case of conjunctival benign reactive lymphoid hyperplasia (BRLH) and a case of central serous chorio-retinopathy. Thermal and non-thermal photographs were taken, and using analyzing software, the ocular surface temperature was calculated. Results: Patient with fresh episode of scleritis revealed high temperature. Eyes with MGD-keratitis depicted lower temperature in clinically more affected eye. Conjunctival BRLH showed a cold lesion on thermography at the site of involvement, in contrast to cases of scleritis with similar clinical presentation. Conclusion: Ocular thermal imaging is an underutilized diagnostic tool which can be used to distinguish inflammatory ocular conditions from non-inflammatory conditions. It can also be utilized in the evaluation of tear film in dry eye syndrome. Its applications should be further explored in uveitis and other ocular disorders. Dedicated “ocular thermographic” camera is today's need of the hour. PMID:24347863

  14. International standards pertaining to thermography practices, training and certification

    NASA Astrophysics Data System (ADS)

    West Åkerblom, Lisa

    2008-03-01

    American, European and International societies establish standards for individuals and companies within the field of infrared thermography. Historically addressing non-destructive testing (NDT) applications and personnel, standards exist and are being developed within the fields of condition monitoring (CM) and building diagnostics. Incorrect reference to or application of standards and guidelines create widespread market confusion. What type of claim can be made against which standards? Does the standard apply to a company or an individual? To what or whom is the standard intended? Does reference to a standard guarantee compliance or imply quality? How does one become educated or involved in standards? An overview of international standards within the field of thermography (with brief reference to recognizable guidelines and standards such as ASNT SNT-TC-1A and CEN 473), their status and application will be presented.

  15. Investigation on a new inducer of pulsed eddy current thermography

    NASA Astrophysics Data System (ADS)

    He, Min; Zhang, Laibin; Zheng, Wenpei; Feng, Yijing

    2016-09-01

    In this paper, a new inducer of pulsed eddy current thermography (PECT) is presented. The use of the inducer can help avoid the problem of blocking the infrared (IR) camera's view in eddy current thermography technique. The inducer can also provide even heating of the test specimen. This paper is concerned with the temperature distribution law around the crack on a specimen when utilizing the new inducer. Firstly, relative mathematical models are provided. In the following section, eddy current distribution and temperature distribution around the crack are studied using the numerical simulation method. The best separation distance between the inducer and the specimen is also determined. Then, results of temperature distribution around the crack stimulated by the inducer are gained by experiments. Effect of current value on temperature rise is studied as well in the experiments. Based on temperature data, temperature features of the crack are discussed.

  16. Thermography Applied to Interfacial Phenomena, Potentials and Pitfalls

    NASA Astrophysics Data System (ADS)

    Antoni, M.; Sefiane, K.

    Infrared (IR) thermography is a non-intrusive method for temperature measurement. Its ability to produce two-dimensional temperature images makes it a powerful tool for investigating systems exhibiting spatial variation of temperature. IR temperature measurements are almost always surface measurements; the technique has therefore found use in obtaining interfacial temperatures, primarily in heat and mass transfer investigations. The reasons for the technique's limited uptake likely stems from the requirement of accurate material emissivity data and the large number of potential sources of error. This chapter provides an overview of the underlying theory of radiative heat transfer. Key considerations and problems in the application of IR thermography are discussed with reference to some examples of recent successful applications.

  17. Glued structures inspection based on lock-in thermography

    NASA Astrophysics Data System (ADS)

    Perez, Laetitia; Autrique, Laurent

    2015-04-01

    Active thermography is a widely employed technique for parametric identification and non-destructive inspection. This attractive method is based on the observation of thermal waves propagation induced by a periodic heating. For nondestructive testing usual approaches are based on a global heating (a large surface of the inspected material is submitted to thermal excitation). In the following a local approach is investigated: the heated area is small (order of magnitude is one square centimeter) and lateral propagation is studied in order to reveal the defect in the sample. In fact, both modulus (heat wave amplitude) and phase lag (delay) of the measured periodic signal are modified by the defect neighborhood and the search for the most effective area leads to the defect localization. Several results are highlighted in this communication in order to investigate an automated procedure. Temperatures are measured by an infrared camera and analyses of modulus cartography are performed in order to estimate the defect location. In such an aim, the downhill simplex method is implemented in order to converge toward defect location. Illustrations are dedicated to glued structures (two plates separated by a thin glue interface) for which unknown defect is a lack of glue which can be considered as a bubble (air trapped between the lower and the upper plane surface). Automated method attractiveness is established in several configurations.

  18. Review of industrial and research applications of thermography

    NASA Astrophysics Data System (ADS)

    Ahlstrom, John

    1990-10-01

    The background and advantages of commercial thermography are reviewed, and applications of thermography in basic research, product development, and medicine are discussed. Industrial applications of thermography to preventive maintenance and production monitoring are also covered.

  19. Human suspicious activity recognition in thermal infrared video

    NASA Astrophysics Data System (ADS)

    Hossen, Jakir; Jacobs, Eddie; Chowdhury, Fahmida K.

    2014-10-01

    Detecting suspicious behaviors is important for surveillance and monitoring systems. In this paper, we investigate suspicious activity detection in thermal infrared imagery, where human motion can be easily detected from the background regardless of the lighting conditions and colors of the human clothing and surfaces. We use locally adaptive regression kernels (LARK) as patch descriptors, which capture the underlying local structure of the data exceedingly well, even in the presence of significant distortions. Patch descriptors are generated for each query patch and for each database patch. A statistical approach is used to match the query activity with the database to make the decision of suspicious activity. Human activity videos in different condition such as, walking, running, carrying a gun, crawling, and carrying backpack in different terrains were acquired using thermal infrared camera. These videos are used for training and performance evaluation of the algorithm. Experimental results show that the proposed approach achieves good performance in suspicious activity recognition.

  20. Using radiation thermography and thermometry to evaluate crop water stress in soybean and cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The use of digital infrared thermography and thermometry to investigate unapparent but important field conditions (poor drainage, non-uniform irrigation, soil variability, or biotic infestations) offers a producer improved management tools to avoid yield declines or to deal with variability in crop ...

  1. Thermography and k-means clustering methods for anti-reflective coating film inspection: scratch and bubble defects

    NASA Astrophysics Data System (ADS)

    Zhou, Xunfei; Wang, Hongjin; Hsieh, Sheng-Jen (Tony)

    2016-05-01

    Anti-reflective coating is widely used on telescopes, eyeglasses and screens to effectively enhance the transmission of light. However, the presence of defects such as bubbles or scratches lowers the usability and functionality of optical film. Optical cameras are often used for coating inspection, but their accuracy relies heavily on the illumination source, camera viewing angles and defect location. This paper describes an active thermography approach that can potentially overcome this issue. Eighteen scratch and bubble defects were located on AR film with dimensions ranging from 0.03mm to 4.4 mm. An infrared camera was used to capture thermal images of those defects over 65 seconds of heating. After the thermal images were acquired, time-domain analysis and space-domain analysis were conducted and k-means clustering methodology was used to highlight the defective area. Results suggest active thermography can be used to detect scratch defects with widths of 0.03mm to 4.40 mm and bubble defects with diameters ranging from 0.08 to 4 mm. For defects with dimensions larger than 0.4 mm, our algorithm can estimate the dimension with less than 15% bias. However, for defects with dimensions less than 0.4mm, the algorithm estimation error ranged from 68% to 900% due to camera resolution limitations. It should be noted that our algorithm can still distinguish a scratch defect with a width of less than one pixel. This study also suggests active thermography can detect scratch and bubble defects regardless of the location of the illumination source.

  2. Biological activities caused by far-infrared radiation

    NASA Astrophysics Data System (ADS)

    Inoué, Shojiro; Kabaya, Morihiro

    1989-09-01

    Contrary to previous presumption, accumulated evidence indicates that far-infrared rays are biologically active. A small ceramic disk that emist far-infrared rays (4 16 μm) has commonly been applied to a local spot or a whole part of the body for exposure. Pioneering attempts to experimentally analyze an effect of acute and chronic radiation of far-infrared rays on living organisms have detected a growth-promoting effect in growing rats, a sleep-modulatory effect in freely behaving rats and an insomiac patient, and a blood circulation-enhancing effect in human skin. Question-paires to 542 users of far-infrared radiator disks embedded in bedelothes revealed that the majority of the users subjectively evaluated an improvement of their health. These effects on living organisms appear to be non-specifically triggered by an exposure to far-infrared rays, which eventually induce an increase in temperature of the body tissues or, more basically, an elevated motility of body fluids due to decrease in size of water clusters.

  3. Aerial thermography in archaeological prospection: Applications & processing

    NASA Astrophysics Data System (ADS)

    Cool, Autumn Chrysantha

    Aerial thermography is one of the least utilized archaeological prospection methods, yet it has great potential for detecting anthropogenic anomalies. Thermal infrared radiation is absorbed and reemitted at varying rates by all objects on and within the ground depending upon their density, composition, and moisture content. If an area containing archaeological features is recorded at the moment when their thermal signatures most strongly contrast with that of the surrounding matrix, they can be visually identified in thermal images. Research conducted in the 1960s and 1970s established a few basic rules for conducting thermal survey, but the expense associated with the method deterred most archaeologists from using this technology. Subsequent research was infrequent and almost exclusively appeared in the form of case studies. However, as the current proliferation of unmanned aerial vehicles (UAVs) and compact thermal cameras draws renewed attention to aerial thermography as an attractive and exciting form of survey, it is appropriate and necessary to reevaluate our approach. In this thesis I have taken a two-pronged approach. First, I built upon the groundwork of earlier researchers and created an experiment to explore the impact that different environmental and climatic conditions have on the success or failure of thermal imaging. I constructed a test site designed to mimic a range of archaeological features and imaged it under a variety of conditions to compare and contrast the results. Second, I explored a new method for processing thermal data that I hope will lead to a means of reducing noise and increasing the clarity of thermal images. This step was done as part of a case study so that the effectiveness of the processing method could be evaluated by comparison with the results of other geophysical surveys.

  4. Inspection of composite structures using line scanning thermography

    NASA Astrophysics Data System (ADS)

    Ley, Obdulia; Butera, Manny; Godinez, Valery

    2012-06-01

    This work deals with the non destructive analysis of different composite parts and structures using Line Scanning Thermography (LST), a non-contact inspection method based in dynamic thermography. The LST technique provides a quick and efficient methodology to scan wide areas rapidly; the technique has been used on the inspection of composite propellers, sandwich panels, motor case tubes and wind turbine blades, among others. In LST a line heat source is used to thermally excite the surface under study while an infrared detector records the transient surface temperature variation of the heated region. Line Scanning Thermography (LST), has successfully been applied to determine the thickness of metallic plates and to assess boiler tube thinning. In this paper the LST protocols developed for the detection of sub-surface defects in different composite materials commonly used in aerospace applications, plates will be presented. In most cases the thermal images acquired using LST will be compared with ultrasonic c-scans. The fundamentals of LST will be discussed, as well as the limitations of this technique for NDT inspection.

  5. Thermography in the follow up of the diabetic foot: best to weigh the enemy more mighty than he seems.

    PubMed

    Pafili, Kalliopi; Papanas, Nikolaos

    2015-03-01

    Thermography is being increasingly appreciated as a further modality contributing to the early detection of incipient tissue damage predisposing to diabetic foot ulceration in selected high-risk patients. Among currently available modalities, liquid crystal thermography and infrared thermography have been most widely used. The former is effective, but its main limitation is low sensitivity. The latter permits non-contact measurements at different angles of the foot, independent of the quality of the camera used. It has been suggested that 5-year use of such techniques for daily self-examination among high-risk patients may contribute to the significant reduction of diabetic foot complications. Clearly, further experience with thermography in the real-life setting is now very welcome.

  6. Infrared-ultraviolet spectra of active galactic nuclei

    NASA Technical Reports Server (NTRS)

    Malkan, M. A.; These corrected SEDs are shown.

    1987-01-01

    Data from IRAS and IUE were combined with ground based optical and infrared spectrophotometry to derive emission line free spectral energy distributions (SEDs) for 29 active galactic nuclei (AGNs) between 0.1 and 100 microns. The IRAS data were scaled down to account for extended emission. These correction factors, determined by comparing small aperture ground based 10.6 micron data with large aperture IRAS 12 micron fluxes, were usually less than 25%. These corrected SEDs are shown.

  7. Calcium imaging of infrared-stimulated activity in rodent brain.

    PubMed

    Cayce, Jonathan Matthew; Bouchard, Matthew B; Chernov, Mykyta M; Chen, Brenda R; Grosberg, Lauren E; Jansen, E Duco; Hillman, Elizabeth M C; Mahadevan-Jansen, Anita

    2014-04-01

    Infrared neural stimulation (INS) is a promising neurostimulation technique that can activate neural tissue with high spatial precision and without the need for exogenous agents. However, little is understood about how infrared light interacts with neural tissue on a cellular level, particularly within the living brain. In this study, we use calcium sensitive dye imaging on macroscopic and microscopic scales to explore the spatiotemporal effects of INS on cortical calcium dynamics. The INS-evoked calcium signal that was observed exhibited a fast and slow component suggesting activation of multiple cellular mechanisms. The slow component of the evoked signal exhibited wave-like properties suggesting network activation, and was verified to originate from astrocytes through pharmacology and 2-photon imaging. We also provide evidence that the fast calcium signal may have been evoked through modulation of glutamate transients. This study demonstrates that pulsed infrared light can induce intracellular calcium modulations in both astrocytes and neurons, providing new insights into the mechanisms of action of INS in the brain.

  8. Non-destructive testing of composite materials used in military applications by eddy current thermography method

    NASA Astrophysics Data System (ADS)

    Swiderski, Waldemar

    2016-10-01

    Eddy current thermography is a new NDT-technique for the detection of cracks in electro conductive materials. It combines the well-established inspection techniques of eddy current testing and thermography. The technique uses induced eddy currents to heat the sample being tested and defect detection is based on the changes of induced eddy currents flows revealed by thermal visualization captured by an infrared camera. The advantage of this method is to use the high performance of eddy current testing that eliminates the known problem of the edge effect. Especially for components of complex geometry this is an important factor which may overcome the increased expense for inspection set-up. The paper presents the possibility of applying eddy current thermography method for detecting defects in ballistic covers made of carbon fiber reinforced composites used in the construction of military vehicles.

  9. Thermography and colour duplex ultrasound assessments of arterio-venous fistula function in renal patients.

    PubMed

    Allen, John; Oates, Crispian P; Chishti, Ahmed D; Ahmed, Ihab A M; Talbot, David; Murray, Alan

    2006-01-01

    Vascular and clinical assessments of arterio-venous fistula (AVF) function and access are important in patients undergoing or preparing to undergo renal dialysis. Objective assessment techniques include colour duplex ultrasound and more recently medical infrared thermography. Ideally, these should help assess problems relating to fistula failure or to vascular steal from the hand which can result from excessive fistula blood flow. The clinical value of thermography, as yet, has not been assessed for this patient group. The aims of this study were therefore to investigate the relationships between thermography skin temperature measurement and (a) quantitative ultrasound measurement of AVF blood flow, and (b) qualitative clinical assessment of vascular steal from the hands. Fifteen adult patients underwent thermal imaging of the upper limbs, colour duplex ultrasound to derive AVF blood flow from brachial artery blood flow measurements, and a clinical evaluation for vascular steal. Temperature measurements were extracted from the thermograms, including bilateral arm and hand (Fistula -- Non-Fistula) differences, for comparison with derived AVF blood flow and steal grading. Derived AVF blood flow ranged from 30 to 1,950 ml min(-1), with a mean rate close to one litre per minute. Thermography detected the warmer superficial veins in proximity to the patent fistulas, with bilateral differences in fistula region skin temperature correlated with derived AVF blood flow (using maximum temperature measurements the correlation was +0.71 [p < 0.01]; and using mean temperature measurements the correlation was +0.56 [p < 0.05]). When thermography measurements were compared with the clinical assessment of steal the mean hand temperature differences separated steal from non-steal patients with an accuracy of greater than 90%. In summary, we have now demonstrated the potential clinical value of medical infrared thermography for assessing AVF function in renal patients.

  10. Seismic risk evaluation aided by IR thermography

    NASA Astrophysics Data System (ADS)

    Grinzato, E.; Cadelano, G.; Bison, P.; Petracca, A.

    2009-05-01

    Conservation of buildings in areas at seismic risk must take prevention into account. The safeguard architectonic heritage is an ambitious objective, but a priority for planning programmes at varying levels of decision making. Preservation and restoration activities must be optimized to cover a vast and widespread historical and architectonic heritage present in many countries. Masonry buildings requires an adequate level of knowledge based on the importance of structural geometry, which may include the damage, details of construction and properties of materials. For identification and classification of masonry is necessary to find shape, type and size of the elements, texture, size of mortar joints, assemblage. The recognition can be done through a visual inspection of the surface of walls, which can be examined, where is not visible, removing a layer of plaster. Thermography is an excellent tool for a fast survey and collection of vital information for this purpose, but it is extremely important define a precise procedure in the development of more efficient monitoring tools. Thermography is a non-destructive method that allows recognizing the structural damage below plaster, detecting the presence of discontinuity in masonry, for added storeys, cavity, filled openings, and repairs. Furthermore, the fast identification of subsurface state allows to select areas where other methods either more penetrating or partially destructive have to be applied. The paper reports experimental results achieved in the mainframe of the European project RECES Modiquus. The main aim of the project is to improve methods, techniques and instruments for facing antiseismic options. Both passive and active thermographic techniques have been applied in different weather conditions and time schemes. A dedicated algorithm has been developed to enhance the visibility of wall bonding.

  11. Distance makes the difference in thermography for ecological studies.

    PubMed

    Faye, E; Dangles, O; Pincebourde, S

    2016-02-01

    Surface temperature drives many ecological processes and infrared thermography is widely used by ecologists to measure the thermal heterogeneity of different species' habitats. However, the potential bias in temperature readings caused by distance between the surface to be measured and the camera is still poorly acknowledged. We examined the effect of distance from 0.3 to 80m on a variety of thermal metrics (mean temperature, standard deviation, patch richness and aggregation) under various weather conditions and for different structural complexity of the studied surface types (various surfaces with vegetation). We found that distance is a key modifier of the temperature measured by a thermal infrared camera. A non-linear relationship between distance and mean temperature, standard deviation and patch richness led to a rapid under-estimation of the thermal metrics within the first 20m and then only a slight decrease between 20 and 80m from the object. Solar radiation also enhanced the bias with increasing distance. Therefore, surface temperatures were under-estimated as distance increased and thermal mosaics were homogenized at long distances with a much stronger bias in the warmer than the colder parts of the distributions. The under-estimation of thermal metrics due to distance was explained by atmospheric composition and the pixel size effect. The structural complexity of the surface had little effect on the surface temperature bias. Finally, we provide general guidelines for ecologists to minimize inaccuracies caused by distance from the studied surface in thermography.

  12. Moisture map by IR thermography

    NASA Astrophysics Data System (ADS)

    Grinzato, E.; Cadelano, G.; Bison, P.

    2010-10-01

    A new approach to moisture detection in buildings by an optical method is presented. Limits of classical and new methods are discussed. The state of the art about the use of IR thermography is illustrated as well. The new technique exploits characteristics of the materials and takes into account explicitly the heat and mass exchange between surface and environment. A set of experiments in controlled laboratory conditions on different materials is used to better understand the physical problem. The testing procedure and the data reduction are illustrated. A case study on a heritage building points up the features of this technique.

  13. Infrared microthermography of microfabricated devices

    SciTech Connect

    Furstenberg, Robert; Kendziora, C. A.; Stepnowski, Stanley V.; McGill, R. Andrew

    2007-06-15

    We report a new experimental apparatus for infrared microthermography applicable to a wide class of samples including semitransparent ones and perforated devices. This setup is particularly well suited for the thermography of microfabricated devices. Traditionally, temperature calibration is performed using calibration hot plates, but this is not applicable to transmissive samples. In this work a custom designed miniature calibration oven in conjunction with spatial filtering is used to obtain accurate static and transient temperature maps of actively heated devices. The procedure does not require prior knowledge of the emissivity. Calibration and image processing algorithms are discussed and analyzed. We show that relatively inexpensive uncooled bolometer arrays can be a suitable detector choice in certain radiometric applications. As an example, we apply this method in the analysis of temperature profiles of an actively heated microfabricated preconcentrator device that incorporates a perforated membrane and is used in trace detection of illicit substances.

  14. Infrared microthermography of microfabricated devices

    NASA Astrophysics Data System (ADS)

    Furstenberg, Robert; Kendziora, C. A.; Stepnowski, Stanley V.; McGill, R. Andrew

    2007-06-01

    We report a new experimental apparatus for infrared microthermography applicable to a wide class of samples including semitransparent ones and perforated devices. This setup is particularly well suited for the thermography of microfabricated devices. Traditionally, temperature calibration is performed using calibration hot plates, but this is not applicable to transmissive samples. In this work a custom designed miniature calibration oven in conjunction with spatial filtering is used to obtain accurate static and transient temperature maps of actively heated devices. The procedure does not require prior knowledge of the emissivity. Calibration and image processing algorithms are discussed and analyzed. We show that relatively inexpensive uncooled bolometer arrays can be a suitable detector choice in certain radiometric applications. As an example, we apply this method in the analysis of temperature profiles of an actively heated microfabricated preconcentrator device that incorporates a perforated membrane and is used in trace detection of illicit substances.

  15. The development of a non-contact screening system for rapid medical inspection at a quarantine depot using a laser Doppler blood-flow meter, microwave radar and infrared thermography.

    PubMed

    Matsui, T; Suzuki, S; Ujikawa, K; Usui, T; Gotoh, S; Sugamata, M; Abe, S

    2009-01-01

    In order to conduct fast screening of passengers with infections such as severe acute respiratory syndrome (SARS) or pandemic influenza at a quarantine depot, we developed a non-contact screening system with self-produced program to conduct a human screening within five seconds, via a linear discriminant function from non-contact derived variables, i.e. palmer pulse derived from a laser Doppler blood-flow meter, respiration rate determined by a 10-GHz microwave radar, and facial temperature measured by thermography. The system evaluation was conducted on seven healthy male subjects (23 +/- 1 years). In order to achieve a pseudo-infection condition, the subjects maintained an ergometer exercise load (100 W, 10 minutes). Before (normal condition) and after (pseudo-infection condition) exercise, a significant linear discriminant function (p < 0.001) was determined to distinguish pseudo-infection condition from normal condition (Mahalanobis D-square = 20.3, classification error rate <5%). The proposed system appears promising for future application in fast screening of infection at a quarantine depot.

  16. Development of a non-contact screening system for rapid medical inspection at a quarantine depot using a laser Doppler blood-flow meter, microwave radar and infrared thermography.

    PubMed

    Matsui, T; Suzuki, S; Ujikawa, K; Usui, T; Gotoh, S; Sugamata, M; Badarch, Z; Abe, S

    2009-01-01

    In order to conduct fast screening of passengers with infections such as severe acute respiratory syndrome (SARS) or pandemic influenza at a quarantine depot, we developed a non-contact screening system with a self-produced program to conduct a human screening within five seconds, via a linear discriminant function from non-contact derived variables, i.e. palmer pulse derived from a laser Doppler blood-flow meter, respiration rate determined by a 10-GHz microwave radar, and facial temperature measured by a thermography. The system evaluation was conducted on seven healthy male subjects (23+1 years). In order to achieve a pseudo-infection condition, the subjects maintained an ergo-meter exercise load (100 W, 10 minutes). Before (normal condition) and after (pseudo-infection condition) exercise, a significant linear discriminant function (p50.001) was determined to distinguish the pseudo-infection condition from the normal condition (Mahalanobis D-square 1/4 20.3, classification error rate55%). The proposed system appears promising for future application in fast screening of infection at a quarantine depot.

  17. Infra-red thermographic evaluation of spinal cord electrostimulation in patients with chronic pain after failed back surgery.

    PubMed

    Devulder, J; Dumoulin, K; De Laat, M; Rolly, G

    1996-08-01

    This study sought to visualize spinal-cord stimulation activity by infra-red thermography in humans suffering from chronic lumbosciatic pain. All the patients had previously undergone neurosurgery for a herniated intervertebral disc. Temperature changes were evaluated in two defined body areas after starting, stopping, maintaining or not starting the stimulation. In one body area, corresponding to the pain location, the patient experienced stimulation paraesthesia, whereas in the non-painful (second) area no stimulation paraesthesia were present. The patients were studied on four consecutive days with a randomly chosen stimulation pattern. Temperature changes in identical and comparable skin areas were measured and statistically analysed. No statistically significant temperature variation was found between the painful and non-painful areas. These findings do not confirm the idea that spinal cord stimulation induces vasodilation in the affected pain area when stimulation is present. Infra-red thermography is not able to differentiate the stimulated from the non-stimulated areas.

  18. Active Sensing with Fabry-Perot Infrared Interferometers

    NASA Astrophysics Data System (ADS)

    Huang, Jin; Gosangi, Rakesh; Gutierrez-Osuna, Ricardo

    2011-09-01

    In this article, we describe an active-sensing framework for infrared (IR) spectroscopy. The goal is to generate a sequence of wavelengths that best discriminates among chemicals. Unlike feature-selection strategies, the sequence is selected on-the-fly as the device acquires data. The framework models the problem as a Partially Observable Markov Decision Process (POMDP), which is solved by a greedy myopic algorithm. In previous work [1], we had applied this framework to temperature-modulated metal oxide sensor. Here, we adapt the framework to a tunable IR sensor based on Fabry-Perot interferometers (FPI). FPIs provide a low-cost alternative to traditional Fourier Transform Infrared Spectroscopy (FTIR), though at the expense of a narrower effective range and lower spectral resolution. Here, we first test whether the framework can scale up to large problems consisting 27 chemicals with 60 dimensions; our previous work on metal oxide sensors employed three chemicals and 7 dimensions. For this purpose, FPI spectra are simulated from FTIR. Then we validate the framework experimentally on 3 chemicals using a prototype instrument based on FPIs. These preliminary results are encouraging and indicate that the framework is able to solve classification problems of reasonable size.

  19. Reliable aerial thermography for energy conservation

    NASA Technical Reports Server (NTRS)

    Jack, J. R.; Bowman, R. L.

    1981-01-01

    A method for energy conservation, the aerial thermography survey, is discussed. It locates sources of energy losses and wasteful energy management practices. An operational map is presented for clear sky conditions. The map outlines the key environmental conditions conductive to obtaining reliable aerial thermography. The map is developed from defined visual and heat loss discrimination criteria which are quantized based on flat roof heat transfer calculations.

  20. Intra-Examiner and Inter-Examiner Reproducibility of Paraspinal Thermography

    PubMed Central

    McCoy, Matthew; Campbell, Ismay; Stone, Pamela; Fedorchuk, Curtis; Wijayawardana, Sameera; Easley, Kirk

    2011-01-01

    Objective The objective of this study was to evaluate the intra-examiner and inter-examiner reproducibility of paraspinal thermography using an infrared scanner. Materials and Methods The thermal functions of a commercially available infrared scanner (Insight Subluxation Station®) were evaluated for clinical reliability. Two practicing clinicians conducted the measures on 100 subjects. Intra class correlation coefficients (ICCs) and concordance correlation coefficients (CCCs) were calculated from the collected data. Results Mean bilateral paraspinal skin temperature was 89.78° F and ranged from 88.77° F to 91.43° F. Intra class correlation coefficients (ICCs) for agreement and consistency ranged from 0.959 to 0.976. Concordance correlation coefficients (CCCs) ranged from 0.783 to 0.859 with tight confidence intervals indicating robust estimates of these quantities. Conclusion This study revealed excellent intra-examiner and inter-examiner reproducibility of paraspinal thermography using a commercially available unit. PMID:21347290

  1. Early events in plant hypersensitive response leaves revealed by IR thermography

    NASA Astrophysics Data System (ADS)

    Boccara, Martine; Boue, Christine; De Paepe, Rosine; Boccara, Albert C.

    2001-10-01

    Infrared thermography is used to reveal the establishment of Erwinia amylovora harpin-induced hypersensitive response (HR) in Nicotiana sylvestris leaves. We observed a decrease in temperature (1-2 degree(s)C) in the harpin infiltrated zone, correlated with an increase in stomatal opening, strongly suggesting that the temperature decrease is due to higher transpiration rate. IRT experiments were conducted in a laboratory environment and could be widely applied for genotype screening and monitoring drug effects.

  2. A combined approach for using thermography for the detection of diabetes mellitus

    NASA Astrophysics Data System (ADS)

    Berry, Bob

    2014-05-01

    This paper presents work done to develop an early diagnosis and monitoring method-encompassing thermography for the detection of Diabetes Mellitus. The early detection method involves fusion of images from infrared cameras, ultrasound devices, a 3D camera and a dermatascope. The project is to develop a novel system that could be easily used by physicians to allow for early intervention, and the paper highlights the approach taken by the Skindetector project.

  3. Methanogenic activity tests by Infrared Tunable Diode Laser Absorption Spectroscopy.

    PubMed

    Martinez-Cruz, Karla; Sepulveda-Jauregui, Armando; Escobar-Orozco, Nayeli; Thalasso, Frederic

    2012-10-01

    Methanogenic activity (MA) tests are commonly carried out to estimate the capability of anaerobic biomass to treat effluents, to evaluate anaerobic activity in bioreactors or natural ecosystems, or to quantify inhibitory effects on methanogenic activity. These activity tests are usually based on the measurement of the volume of biogas produced by volumetric, pressure increase or gas chromatography (GC) methods. In this study, we present an alternative method for non-invasive measurement of methane produced during activity tests in closed vials, based on Infrared Tunable Diode Laser Absorption Spectroscopy (MA-TDLAS). This new method was tested during model acetoclastic and hydrogenotrophic methanogenic activity tests and was compared to a more traditional method based on gas chromatography. From the results obtained, the CH(4) detection limit of the method was estimated to 60 ppm and the minimum measurable methane production rate was estimated to 1.09(.)10(-3) mg l(-1) h(-1), which is below CH(4) production rate usually reported in both anaerobic reactors and natural ecosystems. Additionally to sensitivity, the method has several potential interests compared to more traditional methods among which short measurements time allowing the measurement of a large number of MA test vials, non-invasive measurements avoiding leakage or external interferences and similar cost to GC based methods. It is concluded that MA-TDLAS is a promising method that could be of interest not only in the field of anaerobic digestion but also, in the field of environmental ecology where CH(4) production rates are usually very low.

  4. Thermography and machine learning techniques for tomato freshness prediction.

    PubMed

    Xie, Jing; Hsieh, Sheng-Jen; Wang, Hong-Jin; Tan, Zuojun

    2016-12-01

    The United States and China are the world's leading tomato producers. Tomatoes account for over $2 billion annually in farm sales in the U.S. Tomatoes also rank as the world's 8th most valuable agricultural product, valued at $58 billion dollars annually, and quality is highly prized. Nondestructive technologies, such as optical inspection and near-infrared spectrum analysis, have been developed to estimate tomato freshness (also known as grades in USDA parlance). However, determining the freshness of tomatoes is still an open problem. This research (1) illustrates the principle of theory on why thermography might be able to reveal the internal state of the tomatoes and (2) investigates the application of machine learning techniques-artificial neural networks (ANNs) and support vector machines (SVMs)-in combination with transient step heating, and thermography for freshness prediction, which refers to how soon the tomatoes will decay. Infrared images were captured at a sampling frequency of 1 Hz during 40 s of heating followed by 160 s of cooling. The temperatures of the acquired images were plotted. Regions with higher temperature differences between fresh and less fresh (rotten within three days) tomatoes of approximately uniform size and shape were used as the input nodes for ANN and SVM models. The ANN model built using heating and cooling data was relatively optimal. The overall regression coefficient was 0.99. These results suggest that a combination of infrared thermal imaging and ANN modeling methods can be used to predict tomato freshness with higher accuracy than SVM models.

  5. On-orbit Passive Thermography

    NASA Technical Reports Server (NTRS)

    Howell, Patricia A.; Winfree, William P.; Cramer, K. Elliott

    2008-01-01

    On July 12, 2006, British-born astronaut Piers Sellers became the first person to conduct thermal nondestructive evaluation experiments in space, demonstrating the feasibility of a new tool for detecting damage to the reinforced carbon-carbon (RCC) structures of the Shuttle. This new tool was an EVA (Extravehicular Activity, or spacewalk) compatible infrared camera developed by NASA engineers. Data was collected both on the wing leading edge of the Orbiter and on pre-damaged samples mounted in the Shuttle s cargo bay. A total of 10 infrared movies were collected during the EVA totaling over 250 megabytes of data. Images were downloaded from the orbiting Shuttle to Johnson Space Center for analysis and processing. Results are shown to be comparable to ground-based thermal inspections performed in the laboratory with the same type of camera and simulated solar heating. The EVA camera system detected flat-bottom holes as small as 2.54cm in diameter with 50% material loss from the back (hidden) surface in RCC during this first test of the EVA IR Camera. Data for the time history of the specimen temperature and the capability of the inspection system for imaging impact damage are presented.

  6. [Use of distant thermography in uveitis in children].

    PubMed

    Khvatova, A V; Katargina, L A; Lokhmanov, V P; Zibarov, I N

    1991-01-01

    Forty-four children aged 6 months to 14 years, suffering from endogenous uveitis of various sites were examined at different phases of the diseases by a scanning type apparatus, AGA-780M-thermographer (Sweden). The results permit a conclusion that long-distance thermography may be effectively used to assess the ocular status even in small restless children. Uveitis active phase was found associated with a hyperthermal reaction in all the examined sites. Hyperthermia was found related to uveitis localization. The authors suggest that thermoasymmetry parameters and the corneolimbic gradient be used as additional objective criteria for the assessment of uveitis activity and dissemination in children.

  7. Usefulness of high-resolution thermography in fault diagnosis of fluid power components and systems

    NASA Astrophysics Data System (ADS)

    Pietola, Matti; Varrio, Jukka P.

    1996-03-01

    Infrared thermography has been used routinely in industrial applications for quite a long time. For example, the condition of electric power lines, district heating networks, electric circuits and components, heat exchangers, pipes and its insulations, cooling towers, and various machines and motors is monitored using infrared imaging techniques. Also the usage of this technology in predictive maintenance has proved successful, mainly because of effective computers and tailored softwares available. However, the usage of thermal sensing technique in fluid power systems and components (or other automation systems in fact) is not as common. One apparent reason is that a fluid power circuit is not (and nor is a hydraulic component) an easy object of making thermal image analyses. Especially the high flow speed, fast pressure changes and fast movements make the diagnosis complex and difficult. Also the number of people whose knowledge is good both in thermography and fluid power systems is not significant. In this paper a preliminary study of how thermography could be used in the condition monitoring, fault diagnosis and predictive maintenance of fluid power components and systems is presented. The shortages and limitations of thermal imaging in the condition monitoring of fluid power are also discussed. Among many other cases the following is discussed: (1) pressure valves (leakage, wrong settings), (2) check valves (leakage); (3) cylinders (leakage and other damages); (4) directional valves and valve assemblies; (5) pumps and motors (leakage in piston or control plate, bearings). The biggest advantage of using thermography in the predictive maintenance and fault diagnosis of fluid power components and systems could be achieved in the process industry and perhaps in the commissioning of fluid power systems in the industry. In the industry the predictive maintenance of fluid power with the aid of an infrared camera could be done as part of a condition monitoring of

  8. IR thermography for dynamic detection of laminar-turbulent transition

    NASA Astrophysics Data System (ADS)

    Simon, Bernhard; Filius, Adrian; Tropea, Cameron; Grundmann, Sven

    2016-05-01

    This work investigates the potential of infrared (IR) thermography for the dynamic detection of laminar-turbulent transition. The experiments are conducted on a flat plate at velocities of 8-14 m/s, and the transition of the laminar boundary layer to turbulence is forced by a disturbance source which is turned on and off with frequencies up to 10 Hz. Three different heating techniques are used to apply the required difference between fluid and structure temperature: a heated aluminum structure is used as an internal structure heating technique, a conductive paint acts as a surface bounded heater, while an IR heater serves as an example for an external heating technique. For comparison of all heating techniques, a normalization is introduced and the frequency response of the measured IR camera signal is analyzed. Finally, the different heating techniques are compared and consequences for the design of experiments on laminar-turbulent transition are discussed.

  9. Porosity Measurement in Laminated Composites by Thermography and FEA

    NASA Technical Reports Server (NTRS)

    Chu, Tsuchin Philip; Russell, Samuel S.; Walker, James L.; Munafo, Paul M. (Technical Monitor)

    2001-01-01

    This paper presents the correlation between the through-thickness thermal diffusivity and the porosity of composites. Finite element analysis (FEA) was used to determine the transient thermal response of composites that were subjected to laser heating. A series of finite element models were built and thermal responses for isotropic and orthographic materials with various thermal diffusivities subjected to different heating conditions were investigated. Experiments were conducted to verify the models and to estimate the unknown parameters such as the amount of heat flux. The analysis and experimental results show good correlation between thermal diffusivity and porosity in the composite materials. They also show that both laser and flash heating can be used effectively to obtain thermal diffusivity. The current infrared thermography system is developed for use with flash heating. The laser heating models and the FEA results can provide useful tools to develop practical thermal diffusivity measurement scheme using laser heat.

  10. Fabrication of 0.0075-Scale Orbiter Phosphor Thermography Test Models for Shuttle RTF Aeroheating Studies

    NASA Technical Reports Server (NTRS)

    Buck, Gregory M.; Powers, Michael A.; Griffith, Mark S.; Hopins, John W.; Veneris, Pete H.; Kuykendoll, Kathryn

    2006-01-01

    This report details the techniques and fidelity associated with aeroheating models constructed in support of the return-to-flight boundary layer transition (BLT) activity for STS-114. This report provides technical descriptions of the methods, materials, and equipment used, as well as the surface quality results obtained with the cast ceramic phosphor thermography models.

  11. Quantitative analysis of pulse thermography data for degradation assessment of historical buildings

    NASA Astrophysics Data System (ADS)

    Di Maio, Rosa; Piegari, Ester; Mancini, Cecilia; Chiapparino, Antonella

    2015-06-01

    In the last decades, infrared thermography has been successfully applied to various materials and structures for the assessment of their state of conservation and planning suitable restoration works. To this aim, mathematical models are required to characterize thermal anomaly sources, such as detachments, water infiltration and material decomposition processes. In this paper, an algorithm based on the conservative finite difference method is used to analyse pulse thermography data acquired on an ancient building in the Pompeii archaeological site (Naples, Italy). The numerical study is applied to both broad and narrow elongated thermal anomalies. In particular, from the comparison between simulated and experimental thermal decays, the plaster thickness was characterized in terms of thermal properties and areas of possible future detachments, and moisture infiltration depths were identified.

  12. Thermography-Applications To The Manufacture And Nondestructive Characterization Of Composites

    NASA Astrophysics Data System (ADS)

    Henneke, E. G.; Reifsnider, K. L.; Shuford, R. J.; Hinton, Y. L.; Markert, B. R.

    1983-03-01

    The increasing use of composite materials in military and commercial aircraft requires the development of improved quality control and nondestructive inspection techniques to assure their structural integrity and reliability. Infrared thermography is particularly useful for rapid scanning and detection of manufacturing inhomogeneities and inservice damage states in composites. The relationship between the surface thermal patterns and the interior damage is governed by the type of damage, thermal conductivity of the material and the distance between the surface and the damaged region. Applications of real-time thermography as a quality control technique for processing fiber reinforced composites, and as a nondestructive technique for monitoring growth and development of defects in composite laminates and rotor blades during low-frequency, high amplitude fatigue tests will be discussed. Applications of high frequency vibrothermography for characterizing composite structures will also be presented. This latter technique involves the use of high-frequency, low amplitude ultrasonic excitation of a sample.

  13. Effects of Near-Infrared Laser on Neural Cell Activity

    NASA Astrophysics Data System (ADS)

    Mochizuki-Oda, Noriko; Kataoka, Yosky; Yamada, Hisao; Awazu, Kunio

    2004-08-01

    Near-infrared laser has been used to relieve patients from various kinds of pain caused by postherpetic neuralgesia, myofascial dysfunction, surgical and traumatic wound, cancer, and rheumatoid arthritis. Clinically, He-Ne (λ=632.8 nm, 780 nm) and Ga-Al-As (805 ± 25 nm) lasers are used to irradiate trigger points or nerve ganglion. However the precise mechanisms of such biological actions of the laser have not yet been resolved. Since laser therapy is often effective to suppress the pain caused by hyperactive excitation of sensory neurons, interactions with laser light and neural cells are suggested. As neural excitation requires large amount of energy liberated from adenosine triphosphate (ATP), we examined the effect of 830-nm laser irradiation on the energy metabolism of the rat central nervous system and isolated mitochondria from brain. The diode laser was applied for 15 min with irradiance of 4.8 W/cm2 on a 2 mm-diameter spot at the brain surface. Tissue ATP content of the irradiated area in the cerebral cortex was 19 % higher than that of the non-treated area (opposite side of the cortex), whereas the ADP content showed no significant difference. Irradiation at another wavelength (652 nm) had no effect on either ATP or ADP contents. The temperature of the brain tissue was increased 4.5 - 5.0 °C during the irradiation of both 830-nm and 652-nm laser light. Direct irradiation of the mitochondrial suspension did not show any wavelength-dependent acceleration of respiration rate nor ATP synthesis. These results suggest that the increase in tissue ATP content did not result from the thermal effect, but from specific effect of the laser operated at 830 nm. Electrophysiological studies showed the hyperpolarization of membrane potential of isolated neurons and decrease in membrane resistance with irradiation of the laser, suggesting an activation of potassium channels. Intracellular ATP is reported to regulate some kinds of potassium channels. Possible mechanisms

  14. MID-INFRARED SPECTRAL INDICATORS OF STAR FORMATION AND ACTIVE GALACTIC NUCLEUS ACTIVITY IN NORMAL GALAXIES

    SciTech Connect

    Treyer, Marie; Martin, Christopher D.; Wyder, Ted; Schiminovich, David; O'Dowd, Matt; Johnson, Benjamin D.; Charlot, Stephane; Heckman, Timothy; Martins, Lucimara; Seibert, Mark; Van der Hulst, J. M.

    2010-08-20

    We investigate the use of mid-infrared (MIR) polycyclic aromatic hydrocarbon (PAH) bands, the continuum, and emission lines as probes of star formation (SF) and active galactic nucleus (AGN) activity in a sample of 100 'normal' and local (z {approx} 0.1) emission-line galaxies. The MIR spectra were obtained with the Spitzer Space Telescope Infrared Spectrograph as part of the Spitzer-SDSS-GALEX Spectroscopic Survey, which includes multi-wavelength photometry from the ultraviolet to the far-infrared and optical spectroscopy. The continuum and features were extracted using PAHFIT, a decomposition code which we find to yield PAH equivalent widths (EWs) up to {approx}30 times larger than the commonly used spline methods. Despite the lack of extreme objects in our sample (such as strong AGNs, low-metallicity galaxies, or ULIRGs), we find significant variations in PAH, continuum, and emission-line properties, and systematic trends between these MIR properties and optically derived physical properties, such as age, metallicity, and radiation field hardness. We revisit the diagnostic diagram relating PAH EWs and [Ne II]12.8 {mu}m/[O IV]25.9 {mu}m line ratios and find it to be in much better agreement with the standard optical SF/AGN classification than when spline decompositions are used, while also potentially revealing obscured AGNs. The luminosity of individual PAH components, of the continuum, and, with poorer statistics, of the neon emission lines and molecular hydrogen lines are found to be tightly correlated to the total infrared (TIR) luminosity, making individual MIR components good gauges of the total dust emission in SF galaxies. Like the TIR luminosity, these individual components can be used to estimate dust attenuation in the UV and in H{alpha} lines based on energy balance arguments. We also propose average scaling relations between these components and dust-corrected, H{alpha}-derived SF rates.

  15. Medical applications of model-based dynamic thermography

    NASA Astrophysics Data System (ADS)

    Nowakowski, Antoni; Kaczmarek, Mariusz; Ruminski, Jacek; Hryciuk, Marcin; Renkielska, Alicja; Grudzinski, Jacek; Siebert, Janusz; Jagielak, Dariusz; Rogowski, Jan; Roszak, Krzysztof; Stojek, Wojciech

    2001-03-01

    The proposal to use active thermography in medical diagnostics is promising in some applications concerning investigation of directly accessible parts of the human body. The combination of dynamic thermograms with thermal models of investigated structures gives attractive possibility to make internal structure reconstruction basing on different thermal properties of biological tissues. Measurements of temperature distribution synchronized with external light excitation allow registration of dynamic changes of local temperature dependent on heat exchange conditions. Preliminary results of active thermography applications in medicine are discussed. For skin and under- skin tissues an equivalent thermal model may be determined. For the assumed model its effective parameters may be reconstructed basing on the results of transient thermal processes. For known thermal diffusivity and conductivity of specific tissues the local thickness of a two or three layer structure may be calculated. Results of some medical cases as well as reference data of in vivo study on animals are presented. The method was also applied to evaluate the state of the human heart during the open chest cardio-surgical interventions. Reference studies of evoked heart infarct in pigs are referred, too. We see the proposed new in medical applications technique as a promising diagnostic tool. It is a fully non-invasive, clean, handy, fast and affordable method giving not only qualitative view of investigated surfaces but also an objective quantitative measurement result, accurate enough for many applications including fast screening of affected tissues.

  16. Infrared technology and applications; Proceedings of the Meeting, London, England, June 26-28, 1990

    SciTech Connect

    Lettington, A.H.

    1990-01-01

    Industrial infrared spectroscopy, detectors, applied thermography, optical manufacturing techniques, and optical design and testing are covered. Papers on various aspects of ductile grinding and diamond machining are presented, and focus is placed on thermal signature applications of a high-speed spectroradiometer, and industrial applications of the photothermal effect. Uncooled infrared thermal detector arrays are covered as well as submicron thin-film MOM diodes for the detection of 10-micron infrared laser radiation. Infrared thermal-imaging construction-fault location, industrial and research applications of thermography, and the control of materials by infrared thermography are considered. The optical design of a dual-magnification infrared telescope is presented, and image restoration in thermo-dynamic applications of infrared digital imagery is investigated along with a measurement method for wide-angle afocal telescopes.

  17. The Effect of Penetration Depth on Thermal Contrast of NDT by Thermography

    NASA Technical Reports Server (NTRS)

    Chu, Tsuchin Philip; DiGregorio, Anthony; Russell, Samuel S.

    1999-01-01

    Nondestructive evaluation by Thermography (TNDE) is generally classified into two categories, the passive approach and the active approach. The passive approach is usually performed by measuring the natural temperature difference between the ambient and the material or structure to be tested. The active approach, on the other hand, requires the application of an external energy source to stimulate the material for inspection. A laser, a heater, a hot air blower, a high power thermal pulse, mechanical, or electromagnetic energy may provide the energy sources. For the external heating method to inspect materials for defects and imperfection at ambient temperature, a very short burst of heat can be introduced to one of the surfaces or slow heating of the side opposite to the side being observed. Due to the interruption of the heat flow through the defects, the thermal images will reveal the defective area by contrasting against the surrounding good materials. This technique is called transient Thermography, pulse video Thermography, or thermal wave imaging. As an empirical rule, the radius of the smallest defect should be at least one to two times larger than its depth under the surface. Thermography is being used to inspect void, debond, impact damage, and porosity in composite materials. It has been shown that most of the defects and imperfection can be detected. However, the current method of inspection using thermographic technique is more of an art than a practical scientific and engineering approach. The success rate of determining the defect location and defect type is largely depend on the experience of the person who operates thermography system and performs the inspection. The operator has to try different type of heat source, different duration of its application time, as well as experimenting with the thermal image acquisition time and interval during the inspection process. Further-more, the complexity of the lay-up and structure of composites makes it

  18. Assessing the reliability of thermography to infer internal body temperatures of lizards.

    PubMed

    Barroso, Frederico M; Carretero, Miguel A; Silva, Francisco; Sannolo, Marco

    2016-12-01

    For many years lizard thermal ecology studies have relied on the use of contact thermometry to obtain internal body temperature (Tb) of the animals. However, with progressing technology, an interest grew in using new, less invasive methods, such as InfraRed (IR) pyrometry and thermography, to infer Tb of reptiles. Nonetheless few studies have tested the reliability of these new tools. The present study tested the use of IR cameras as a non-invasive tool to infer Tb of lizards, using three differently body-sized lacertid species (Podarcis virescens, Lacerta schreiberi and Timon lepidus). Given the occurrence of regional heterothermy, we pairwise compared thermography readings of six body parts (snout, eye, head, dorsal, hind limb, tail base) to cloacal temperature (measured by a thermometer-associated thermocouple probe) commonly employed to measure Tb in field and lab studies. The results showed moderate to strong correlations (R(2)=0.84-0.99) between all body parts and cloacal temperature. However, despite the readings on the tail base showed the strongest correlation in all three species, it was the eye where the absolute values and pattern of temperature change most consistently followed the cloacal measurements. Hence, we concluded that the eye would be the body location whose IR camera readings more closely approximate that of the animal's internal environment. Alternatively, other body parts can be used, provided that a careful calibration is carried out. We provide guidelines for future research using thermography to infer Tb of lizards.

  19. Comparison of Detection Capability for Acoustic Thermography, Visual Inspection and Fluorescent Penetrant Inspection on Gas Turbine Components

    NASA Astrophysics Data System (ADS)

    Guo, Y.; Ruhge, F. R.

    2009-03-01

    The innovative NDE inspection system Acoustic Thermography is developed with Sonic Infrared (Sonic IR) technology. Since the probability of detection is sensitive to the flaw characteristics, the fabricated flaws could not simulated the nature flaws with accuracy. The study is focus on gas turbine blades with service induced fatigue cracks. The detection capability of this innovative NDE inspection system is compared with two traditional NDE methods: Visual Inspection and Fluorescent Penetrant Inspection. POD curves for each technique were generated and compared.

  20. Assessment of Lower Limb Prosthesis through Wearable Sensors and Thermography

    PubMed Central

    Cutti, Andrea Giovanni; Perego, Paolo; Fusca, Marcello C.; Sacchetti, Rinaldo; Andreoni, Giuseppe

    2014-01-01

    This study aimed to explore the application of infrared thermography in combination with ambulatory wearable monitoring of temperature and relative humidity, to assess the residual limb-to-liner interface in lower-limb prosthesis users. Five male traumatic transtibial amputees were involved, who reported no problems or discomfort while wearing the prosthesis. A thermal imaging camera was used to measure superficial thermal distribution maps of the stump. A wearable system for recording the temperature and relative humidity in up to four anatomical points was developed, tested in vitro and integrated with the measurement set. The parallel application of an infrared camera and wearable sensors provided complementary information. Four main Regions of Interest were identified on the stump (inferior patella, lateral/medial epicondyles, tibial tuberosity), with good inter-subject repeatability. An average increase of 20% in hot areas (P < 0.05) is shown after walking compared to resting conditions. The sensors inside the cuff did not provoke any discomfort during recordings and provide an inside of the thermal exchanges while walking and recording the temperature increase (a regime value is ∼+1.1 ± 0.7 °C) and a more significant one (∼+4.1 ± 2.3%) in humidity because of the sweat produced. This study has also begun the development of a reference data set for optimal socket/liner-stump construction. PMID:24618782

  1. Inferring deep-brain activity from cortical activity using functional near-infrared spectroscopy.

    PubMed

    Liu, Ning; Cui, Xu; Bryant, Daniel M; Glover, Gary H; Reiss, Allan L

    2015-03-01

    Functional near-infrared spectroscopy (fNIRS) is an increasingly popular technology for studying brain function because it is non-invasive, non-irradiating and relatively inexpensive. Further, fNIRS potentially allows measurement of hemodynamic activity with high temporal resolution (milliseconds) and in naturalistic settings. However, in comparison with other imaging modalities, namely fMRI, fNIRS has a significant drawback: limited sensitivity to hemodynamic changes in deep-brain regions. To overcome this limitation, we developed a computational method to infer deep-brain activity using fNIRS measurements of cortical activity. Using simultaneous fNIRS and fMRI, we measured brain activity in 17 participants as they completed three cognitive tasks. A support vector regression (SVR) learning algorithm was used to predict activity in twelve deep-brain regions using information from surface fNIRS measurements. We compared these predictions against actual fMRI-measured activity using Pearson's correlation to quantify prediction performance. To provide a benchmark for comparison, we also used fMRI measurements of cortical activity to infer deep-brain activity. When using fMRI-measured activity from the entire cortex, we were able to predict deep-brain activity in the fusiform cortex with an average correlation coefficient of 0.80 and in all deep-brain regions with an average correlation coefficient of 0.67. The top 15% of predictions using fNIRS signal achieved an accuracy of 0.7. To our knowledge, this study is the first to investigate the feasibility of using cortical activity to infer deep-brain activity. This new method has the potential to extend fNIRS applications in cognitive and clinical neuroscience research.

  2. Research on lock-in thermography for aerospace materials of nondestructive test based on image sequence processing

    NASA Astrophysics Data System (ADS)

    Liu, Junyan; Dai, Jingmin; Wang, Yang

    2008-11-01

    IR Lock in thermography is an active thermography technology based on thermal wave signal processing, especially, it has many advantages for nondestructive test of composite materials and compound structure application and has been applied on aerospace, automotive, mechanics and electric fields. In lock in thermography, given sufficient time for periodic heating, the surface temperature will evolve periodically in a sinusoidal pattern form the transient state to the steady state. In this paper, the principle of lock in thermography is introduced and the heat transferring process is analyzed by the sinusoidal variation heating flow transferred in materials by means of FEM method. In experiment, the modulating optical stimulation is applied to sample, and image sequences are collected by Jade MWIR 550 FPA IR camera. The digital filter algorithm which is Savitzky-Golay digital smoothness filters is used to remove the effects of high frequency noise. A phase image at the frequency of periodic heating can be calculated using a Fourier transform of the periodic heating frequency in transient state for defect detection. The IR lock in thermography processing software is developed by using of visual C++ programmed based image sequence collected. The experimental results show that the developed system reached up to high level of conventional steady state Lock in method.

  3. Optically active substituted polyacetylene@carbon nanotube hybrids: Preparation, characterization and infrared emissivity property study

    SciTech Connect

    Bu, Xiaohai; Zhou, Yuming Zhang, Tao; Wang, Yongjuan; Zhang, Zewu; He, Man

    2014-08-15

    Optically active substituted polyacetylene@multiwalled carbon nanotubes (SPA@MWCNTs) nanohybrids were fabricated by wrapping helical SPA copolymers onto the surface of modified nanotubes through ester bonding linkage. SPA copolymer based on chiral phenylalanine and serine was pre-polymerized by a rhodium zwitterion catalyst in THF, and evidently proved to possess strong optical activity and adopt a predominately one-handed helical conformation. Various characterizations including Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and transmission electron microscopy (TEM) demonstrated that the SPA had been covalently grafted onto the nanotubes without destroying their original graphite structure. The wrapped SPA was found to exhibit an enhancement in thermal stability and still maintained considerable optical activity after grafting. The infrared emissivity property of the nanohybrids at 8–14 μm was investigated in addition. The results indicated that the SPA@MWCNTs hybrid matrix could possess a much lower infrared emissivity value (ε=0.707) than raw MWCNTs, which might be due to synergistic effect of the unique helical conformation of optically active SPA and strengthened interfacial interaction between the organic polymers and inorganic nanoparticles. - Graphical abstract: Optically active SPA@MWCNTs nanohybrids with low infrared emissivity. - Highlights: • Synthesis of optically active SPA copolymer derived from serine and phenylalanine. • Preparation and characterization of optically active SPA@MWCNTs nanohybrids. • Application study of the SPA@MWCNTs nanohybrids (ε=0.707) in lowering the infrared emissivity.

  4. Applications of infrared technology; Proceedings of the Meeting, London, England, June 9, 10, 1988

    NASA Astrophysics Data System (ADS)

    Williams, T. L.

    1988-01-01

    Recent developments in thermal imaging and other infrared systems relating to military, industrial, medical, and scientific applications are reviewed. Papers are presented on a new thermal imager using a linear pyroelectric detector array; multichannel near infrared spectroradiometer; technological constraints on the use of thermal imagery for remote sensing; and infrared optical system of the improved stratospheric and mesospheric sounder. Other topics discussed include infrared thermography development for composite material evaluation; infrared process linescanner, and optical infrared starting radiometer.

  5. Evidence for Infrared-faint Radio Sources as z > 1 Radio-loud Active Galactic Nuclei

    NASA Astrophysics Data System (ADS)

    Huynh, Minh T.; Norris, Ray P.; Siana, Brian; Middelberg, Enno

    2010-02-01

    Infrared-Faint Radio Sources (IFRSs) are a class of radio objects found in the Australia Telescope Large Area Survey which have no observable mid-infrared counterpart in the Spitzer Wide-area Infrared Extragalactic (SWIRE) survey. The extended Chandra Deep Field South now has even deeper Spitzer imaging (3.6-70 μm) from a number of Legacy surveys. We report the detections of two IFRS sources in IRAC images. The non-detection of two other IFRSs allows us to constrain the source type. Detailed modeling of the spectral energy distribution of these objects shows that they are consistent with high-redshift (z >~ 1) active galactic nuclei.

  6. Long distance active hyperspectral sensing using high-power near-infrared supercontinuum light source.

    PubMed

    Manninen, Albert; Kääriäinen, Teemu; Parviainen, Tomi; Buchter, Scott; Heiliö, Miika; Laurila, Toni

    2014-03-24

    A hyperspectral remote sensing instrument employing a novel near-infrared supercontinuum light source has been developed for active illumination and identification of targets. The supercontinuum is generated in a standard normal dispersion multi-mode fiber and has 16 W total optical output power covering 1000 nm to 2300 nm spectral range. A commercial 256-channel infrared spectrometer was used for broadband infrared detection. The feasibility of the presented hyperspectral measurement approach was investigated both indoors and in the field. Reflection spectra from several diffusive targets were successfully measured and a measurement range of 1.5 km was demonstrated.

  7. Quantitative Evaluation of Pulsed Thermography, Lock-in Thermography and Vibrothermography on Foreign Object Defect (FOD) in CFRP.

    PubMed

    Liu, Bin; Zhang, Hai; Fernandes, Henrique; Maldague, Xavier

    2016-05-21

    In this article, optical excitation thermographic techniques, including pulsed thermography and lock-in thermography, were used to detect foreign object defect (FOD) and delamination in CFRP. Then, vibrothermography as an ultrasonic excitation technique was used to detect these defects for the comparative purposes. Different image processing methods, including cold image subtraction (CIS), principal component thermography (PCT), thermographic signal reconstruction (TSR) and Fourier transform (FT), were performed. Finally, a comparison of optical excitation thermography and vibrothermography was conducted, and a thermographic probability of detection was given.

  8. Quantitative Evaluation of Pulsed Thermography, Lock-in Thermography and Vibrothermography on Foreign Object Defect (FOD) in CFRP

    PubMed Central

    Liu, Bin; Zhang, Hai; Fernandes, Henrique; Maldague, Xavier

    2016-01-01

    In this article, optical excitation thermographic techniques, including pulsed thermography and lock-in thermography, were used to detect foreign object defect (FOD) and delamination in CFRP. Then, vibrothermography as an ultrasonic excitation technique was used to detect these defects for the comparative purposes. Different image processing methods, including cold image subtraction (CIS), principal component thermography (PCT), thermographic signal reconstruction (TSR) and Fourier transform (FT), were performed. Finally, a comparison of optical excitation thermography and vibrothermography was conducted, and a thermographic probability of detection was given. PMID:27213403

  9. Mid-infrared Colors of Dwarf Galaxies: Young Starbursts Mimicking Active Galactic Nuclei

    NASA Astrophysics Data System (ADS)

    Hainline, Kevin N.; Reines, Amy E.; Greene, Jenny E.; Stern, Daniel

    2016-12-01

    Searching for active galactic nuclei (AGNs) in dwarf galaxies is important for our understanding of the seed black holes that formed in the early universe. Here, we test infrared selection methods for AGN activity at low galaxy masses. Our parent sample consists of ˜18,000 nearby dwarf galaxies (M * < 3 × 109 M ⊙, z < 0.055) in the Sloan Digital Sky Survey with significant detections in the first three bands of the AllWISE data release from the Wide-field Infrared Survey Explorer (WISE). First, we demonstrate that the majority of optically selected AGNs in dwarf galaxies are not selected as AGNs using WISE infrared color diagnostics and that the infrared emission is dominated by the host galaxies. We then investigate the infrared properties of optically selected star-forming dwarf galaxies, finding that the galaxies with the reddest infrared colors are the most compact, with blue optical colors, young stellar ages, and large specific star formation rates. These results indicate that great care must be taken when selecting AGNs in dwarf galaxies using infrared colors, as star-forming dwarf galaxies are capable of heating dust in such a way that mimics the infrared colors of more luminous AGNs. In particular, a simple W1-W2 color cut alone should not be used to select AGNs in dwarf galaxies. With these complications in mind, we present a sample of 41 dwarf galaxies that fall in the WISE infrared color space typically occupied by more luminous AGNs and that are worthy of follow-up observations.

  10. Urban Heat Islands and Urban Thermography

    NASA Astrophysics Data System (ADS)

    Manunta, Paolo; Ceriola, Giulio; Daglis, Ioannis A.; de Ridder, Koen; Giannaros, Theodoros; Keramitsoglou, Iphigenia; Maiheu, Bino; Melas, Dimitrios; Montero Herrero, Enrique; Paganini, Marc; Palacios, Marino; Radius, Andrea; Sapage, Tania; Tamame, Maria; Tambuyzer, Han; Viel, Monique

    2010-12-01

    The Urban Heat Island (UHI) and Urban Thermography project is a project funded by ESA under the DUE program. The project started on 1st November 2008 and will last 2.5 years. The UHI project is relying on all satellite missions that embark TIR sensors to analyse the spatial variability of the Urban Heat Islands in the metropolitan areas of 10 European cities over the last 10 years. Moreover, thermography mapping using airborne data have been or will be performed for Athens, Madrid and Brussels. The project is contributing to the 'Reorientation of the Fuegosat Consolidation Phase', through the collection and synthesis of user requirements for a frequent and routine observation of surface and air temperatures in the core of the major European cities and in the surrounding peri-urban areas.

  11. Characterization of an Inclusion of Plastazote Located in an Academic Fresco by Photothermal Thermography

    NASA Astrophysics Data System (ADS)

    Bodnar, J. L.; Nicolas, J. L.; Mouhoubi, K.; Candore, J. C.; Detalle, V.

    2013-09-01

    The aim of this study is to approach the possibilities of stimulated infrared thermography in dimensional characterization of defects situated in mural paintings. For this purpose, it is suggested to proceed in two stages. First, an in situ longitudinal thermal-diffusivity measurement is developed. Then the characterization of the depth of the studied defect by means of an extended photothermal analysis and a comparison between theory and experiment is carried out. In this article is shown that this approach allows a good estimate of the depth of a plastazote inclusion in a partial copy of the “Saint Christophe” of the Campana collection in the Louvre Museum.

  12. Photothermal Thermography Applied to the Non-destructive Testing of Different Types of Works of Art

    NASA Astrophysics Data System (ADS)

    Bodnar, J. L.; Mouhoubi, K.; Szatanik-Perrier, G.; Vallet, J. M.; Detalle, V.

    2012-11-01

    In this article, various cases in helping to restore works of art by stimulated infrared thermography are presented. First, the method allows detecting old restorations found on a mural painting in the French senate. Then, it is demonstrated how the photothermal method enables determination of the underlying structure of the mural painting "The Apotheosis of Saint Bruno" in the Charterhouse of Villeneuve-lez-Avignon. Finally, the method allows locating separate canvas paintings on "Avenant de l'aurore" in the "Luxembourg" French Senate building.

  13. Active Control of Nitride Plasmonic Dispersion in the Far Infrared.

    SciTech Connect

    Shaner, Eric A.; Dyer, Gregory Conrad; Seng, William Francis; Bethke, Donald Thomas; Grine, Albert Dario,; Baca, Albert G.; Allerman, Andrew A.

    2014-11-01

    We investigate plasmonic structures in nitride-based materials for far-infrared (IR) applications. The two dimensional electron gas (2DEG) in the GaN/AlGaN material system, much like metal- dielectric structures, is a patternable plasmonic medium. However, it also permits for direct tunability via an applied voltage. While there have been proof-of-principle demonstrations of plasma excitations in nitride 2DEGs, exploration of the potential of this material system has thus far been limited. We recently demonstrated coherent phenomena such as the formation of plasmonic crystals, strong coupling of tunable crystal defects to a plasmonic crystal, and electromagnetically induced transparency in GaAs/AlGaAs 2DEGs at sub-THz frequencies. In this project, we explore whether these effects can be realized in nitride 2DEG materials above 1 THz and at temperatures exceeding 77 K.

  14. Characterization of Io's Volcanic Activity by Infrared Polarimetry.

    PubMed

    Goguen, J D; Sinton, W M

    1985-10-04

    The thermal emission from Io's volcanic hot spots is linearly polarized. Infrared measurements at 4.76 micrometers show disk-integrated polarization as large as 1.6 percent. The degree and position angle of linear polarization vary with Io's rotation in a manner characteristic of emission from a small number of hot spots. A model incorporating three hot spots best fits the data. The largest of these hot spots lies to the northeast of Loki Patera, as mapped from Voyager, and the other spot on the trailing hemisphere is near Ra Patera. The hot spot on the leading hemisphere corresponds to no named feature on the Voyager maps. The value determined for the index of refraction of the emitting surface is a lower bound; it is similar to that of terrestrial basalts and is somewhat less than that of sulfur.

  15. Characterization of Io's volcanic activity by infrared polarimetry

    SciTech Connect

    Goguen, J.D.; Sinton, W.M.

    1985-10-01

    The thermal emission from Io's volcanic hot spots is linearly polarized.Infrared measurements at 4.76 micrometers show disk-integrated polarization as large as 1.6 percent. The degree and position angle of linear polarization vary with Io's rotation in a manner characteristic of emission from a small number of hot spots. A model incorporating three hot spots best fits the data. The largest of these hot spots lies to the northeast of Loki Patera, as mapped from Voyager, and the other spot on the trailing hemisphere is near Ra Patera. The hot spot on the leading hemisphere corresponds to no named feature on the Voyager maps. The value determined for the index of refraction of the emitting surface is a lower bound; it is similar to that of terrestrial basalts and is somewhat less than that of sulfur. 25 references.

  16. Corrosion detection on pipelines by IR thermography

    NASA Astrophysics Data System (ADS)

    Bison, P.; Marinetti, S.; Cuogo, G.; Molinas, B.; Zonta, P.; Grinzato, E.

    2011-05-01

    IR thermography is applied to detect hidden corrosion on carbon steel pipelines for oil transportation. The research is oriented to set up a robust technique to carry out in situ the early detection of corroded zones that may evolve either towards leakage or failure. The use of thermography associated with a transient thermal technique is investigated on 12.2 mm thick samples, machined to artificially create a reduction of wall thickness that simulates the effect of real corrosion in pipes. The extension and depth of the artificial defects is controlled by ultrasounds which represents the reference for the results obtained by thermography. Two approaches are proposed: the first is based on the processing of a single thermogram taken at the optimum time after a finite pulse heating of a large area of the external surface; the second technique is carried out by scanning the pipeline by means of a device composed of a linear lamp and a thermographic camera which move jointly over the surface to test. A suitable reconstruction provides a map of the tested surface with possible hot spots in correspondence with the corroded areas. The analysis of the thermal problem by Finite Element Method is used to optimize the experimental parameters. The experimental results demonstrate a detection capability starting from 15 % of wall thickness reduction.

  17. Study on the activation of styrene-based shape memory polymer by medium-infrared laser light

    NASA Astrophysics Data System (ADS)

    Leng, Jinsong; Zhang, Dawei; Liu, Yanju; Yu, Kai; Lan, Xin

    2010-03-01

    This paper demonstrates the feasibility of shape memory polymer (SMP) activation by medium-infrared laser light. Medium-infrared light is transmitted by an optical fiber embedded in the SMP matrix, and the shape recovery process and temperature distribution are recorded by an infrared camera. Light-induced SMP exhibits potential applications in biomedicines and flexible displays.

  18. Gamma-irradiation tests of IR optical fibres for ITER thermography--a case study

    SciTech Connect

    Reichle, R.; Pocheau, C.; Jouve, M.

    2008-03-12

    In the course of the development of a concept for a spectrally resolving infrared thermography diagnostic for the ITER divertor we have tested 3 types of infrared (IR) fibres in Co{sup 60} irradiation facilities under {gamma} irradiation. The fibres were ZrF{sub 4} (and HfF{sub 4}) fibres from different manufacturers, hollow fibres (silica capillaries with internal Ag/AgJ coating) and a sapphire fibre. For the IR range, only the latter fibre type encourages to go further for neutron tests in a reactor. If one restricted the interest onto the near infrared range, high purity core silica fibres could be used. This study might be seen as a typical example of the relation between diagnostic development for a nuclear environment and irradiation experiments.

  19. MID- AND FAR-INFRARED PROPERTIES OF A COMPLETE SAMPLE OF LOCAL ACTIVE GALACTIC NUCLEI

    SciTech Connect

    Ichikawa, Kohei; Ueda, Yoshihiro; Terashima, Yuichi; Oyabu, Shinki; Gandhi, Poshak; Nakagawa, Takao; Matsuta, Keiko

    2012-07-20

    We investigate the mid- (MIR) to far-infrared (FIR) properties of a nearly complete sample of local active galactic nuclei (AGNs) detected in the Swift/Burst Alert Telescope (BAT) all-sky hard X-ray (14-195 keV) survey, based on the cross correlation with the AKARI infrared survey catalogs complemented by those with Infrared Astronomical Satellite and Wide-field Infrared Survey Explorer. Out of 135 non-blazer AGNs in the Swift/BAT nine-month catalog, we obtain the MIR photometric data for 128 sources either in the 9, 12, 18, 22, and/or 25 {mu}m band. We find good correlation between their hard X-ray and MIR luminosities over three orders of magnitude (42 < log {lambda}L{sub {lambda}}(9, 18 {mu}m) < 45), which is tighter than that with the FIR luminosities at 90 {mu}m. This suggests that thermal emission from hot dusts irradiated by the AGN emission dominate the MIR fluxes. Both X-ray unabsorbed and absorbed AGNs follow the same correlation, implying isotropic infrared emission, as expected in clumpy dust tori rather than homogeneous ones. We find excess signals around 9 {mu}m in the averaged infrared spectral energy distribution from heavy obscured 'new type' AGNs with small scattering fractions in the X-ray spectra. This could be attributed to the polycyclic aromatic hydrocarbon emission feature, suggesting that their host galaxies have strong starburst activities.

  20. Near-infrared light activated delivery platform for cancer therapy.

    PubMed

    Lin, Min; Gao, Yan; Hornicek, Francis; Xu, Feng; Lu, Tian Jian; Amiji, Mansoor; Duan, Zhenfeng

    2015-12-01

    Cancer treatment using conventional drug delivery platforms may lead to fatal damage to normal cells. Among various intelligent delivery platforms, photoresponsive delivery platforms are becoming popular, as light can be easily focused and tuned in terms of power intensity, wavelength, and irradiation time, allowing remote and precise control over therapeutic payload release both spatially and temporally. This unprecedented controlled delivery manner is important to improve therapeutic efficacy while minimizing side effects. However, most of the existing photoactive delivery platforms require UV/visible excitation to initiate their function, which suffers from phototoxicity and low level of tissue penetration limiting their practical applications in biomedicine. With the advanced optical property of converting near infrared (NIR) excitation to localized UV/visible emission, upconversion nanoparticles (UCNPs) have emerged as a promising photoactive delivery platform that provides practical applications for remote spatially and temporally controlled release of therapeutic payload molecules using low phototoxic and high tissue penetration NIR light as the excitation source. This article reviews the state-of-the-art design, synthesis and therapeutic molecular payload encapsulation strategies of UCNP-based photoactive delivery platforms for cancer therapy. Challenges and promises for engineering of advanced delivery platforms are also highlighted.

  1. High dynamic range infrared thermography by pixelwise radiometric self calibration

    NASA Astrophysics Data System (ADS)

    Ochs, M.; Schulz, A.; Bauer, H.-J.

    2010-03-01

    A procedure is described where the response function of each pixel of an InSb detector is determined by radiometric self-calibration. With the present approach no knowledge of the spectral characteristics of the IR system is required to recover a quantity which is linear with the incident irradiance of the object. The inherent detector non-uniformity is corrected on the basis of self-calibrated scaled irradiance. Compared to the standard two-point non-uniformity correction procedure - performed with the detector signal - only two NUC-tables are required for arbitrary integration times. Images obtained at various exposures are fused to a single high dynamic range image. The procedure is validated with synthetic data and its performance is demonstrated by measurements performed with a high resolution InSb FPA.

  2. Using Infrared Thermography to Assess Emotional Responses to Infants

    ERIC Educational Resources Information Center

    Esposito, Gianluca; Nakazawa, Jun; Ogawa, Shota; Stival, Rita; Putnick, Diane L.; Bornstein, Marc H.

    2015-01-01

    Adult-infant interactions operate simultaneously across multiple domains and at multiple levels -- from physiology to behaviour. Unpackaging and understanding them, therefore, involve analysis of multiple data streams. In this study, we tested physiological responses and cognitive preferences for infant and adult faces in adult females and males.…

  3. Multichannel and multicolour infrared thermography in Tore Supra

    SciTech Connect

    Reichle, R.; Pocheau, C.; Balorin, C.; Delchambre, E.; Desgrange, C.; Guilhem, D.; Henry, S.; Messina, P.; Roche, H.

    2004-10-01

    An imaging spectrometer using a sapphire prism as dispersing element has been conceived at Tore Supra for the spectral range of 1-4 {mu}m. It measures simultaneously at various wavelengths the temperature on distributed high heat-flux elements under plasma impact with 36 optical fibers, four of which are ZrF{sub 4} fibers. It employs an InSb focal plane array detector (256*320 pixels) behind a silicon filter and a ZnS window yielding a dynamic range of 200-1500 deg. C with 20 ms temporal resolution. The fiber transmission and the spatial variation of gain and background of the camera are calibrated using a light source with integrating sphere. With a blackbody source one determines the nonlinearity of the average gain and controls its stability during operation. The spectral dispersion of about 24 nm/pixel is determined with interference filters and controlled with a spectral lamp. The measurements at various wavelengths allow to determine the temperature distribution in the field of view.

  4. Spectral components at visual and infrared wavelengths in active galactic nuclei

    NASA Technical Reports Server (NTRS)

    Stein, W. A.; Tokunaga, A. T.; Rudy, R. J.

    1984-01-01

    Aperture-dependent infrared photometry of active galactic nuclei are presented which illustrate the importance of eliminating starlight of the galaxy in order to obtain the intrinsic spectral distribution of the active nuclei. Separate components of emission are required to explain the infrared emission with a spectral index of alpha approx = 2 and the typical visual-ultraviolet continuum with alpha approx = 0.3 (where F(nu) varies as nu(sup-alpha). Present evidence does not allow unique determination of the appropriate mechanisms, but the characteristics of each are discussed.

  5. Human brain activity with near-infrared spectroscopy

    NASA Astrophysics Data System (ADS)

    Luo, Qingming; Chance, Britton

    1999-09-01

    Human brain activity was studied with a real time functional Near-InfraRed Imager (fNIRI). The imager has 16 measurement channels and covers 4 cm by 9 cm detection area. Brain activities in occipital, motor and prefrontal area were studied with the fNIRI. In prefrontal stimulation, language cognition, analogies, forming memory for new associations, emotional thinking, and mental arithmetic were carried out. Experimental results measured with fNIRI are demonstrated in this paper. It was shown that fNIRI technique is able to reveal the occipital activity during visual stimulation, and co-register well with results of fMRI in the motor cortex activity during finger tapping. In the studies of the effects of left prefrontal lobe on forming memory for new associations, it is shown that left prefrontal lobe activated more under deep conditions than that under shallow encoding, especially the dorsal part. In the studies of emotional thinking, it was shown that the responses were different between positive- negative emotional thinking and negative-positive emotional thinking. In mental arithmetic studies, higher activation was found in the first task than in the second, regardless of the difficulty, and higher activation was measured in subtraction of 17 than in subtraction of 3.

  6. Method for improving visualization of infrared images

    NASA Astrophysics Data System (ADS)

    Cimbalista, Mario

    2014-05-01

    Thermography has an extremely important difference from the other visual image converting electronic systems, like XRays or ultrasound: the infrared camera operator usually spend hour after hour with his/her eyes looking only at infrared images, sometimes several intermittent hours a day if not six or more continuous hours. This operational characteristic has a very important impact on yield, precision, errors and misinterpretation of the infrared images contents. Despite a great hardware development over the last fifty years, quality infrared thermography still lacks for a solution for these problems. The human eye physiology has not evolved to see infrared radiation neither the mind-brain has the capability to understand and decode infrared information. Chemical processes inside the human eye and functional cells distributions as well as cognitive-perceptual impact of images plays a crucial role in the perception, detection, and other steps of dealing with infrared images. The system presented here, called ThermoScala and patented in USA solves this problem using a coding process applicable to an original infrared image, generated from any value matrix, from any kind of infrared camera to make it much more suitable for human usage, causing a substantial difference in the way the retina and the brain processes the resultant images. The result obtained is a much less exhaustive way to see, identify and interpret infrared images generated by any infrared camera that uses this conversion process.

  7. A COMPARISON OF X-RAY AND MID-INFRARED SELECTION OF OBSCURED ACTIVE GALACTIC NUCLEI

    SciTech Connect

    Eckart, Megan E.; Harrison, Fiona A.; McGreer, Ian D.; Helfand, David J.; Stern, Daniel

    2010-01-01

    We compare the relative merits of active galactic nuclei (AGNs) selection at X-ray and mid-infrared wavelengths using data from moderately deep fields observed by both Chandra and Spitzer. The X-ray-selected AGN sample and associated photometric and spectroscopic optical follow-up are drawn from a subset of fields studied as part of the Serendipitous Extragalactic X-ray Source Identification (SEXSI) program. Mid-infrared data in these fields are derived from targeted and archival Spitzer imaging, and mid-infrared AGN selection is accomplished primarily through application of the Infrared Array Camera (IRAC) color-color AGN 'wedge' selection technique. Nearly all X-ray sources in these fields which exhibit clear spectroscopic signatures of AGN activity have mid-infrared colors consistent with IRAC AGN selection. These are predominantly the most luminous X-ray sources. X-ray sources that lack high-ionization and/or broad lines in their optical spectra are far less likely to be selected as AGNs by mid-infrared color selection techniques. The fraction of X-ray sources identified as AGNs in the mid-infrared increases monotonically as the X-ray luminosity increases. Conversely, only 22% of mid-infrared-selected AGNs are detected at X-ray energies in the moderately deep ((t{sub exp}) approx 100 ks) SEXSI Chandra data. We hypothesize that IRAC sources with AGN colors that lack X-ray detections are predominantly high-luminosity AGNs that are obscured and/or lie at high redshift. A stacking analysis of X-ray-undetected sources shows that objects in the mid-infrared AGN selection wedge have average X-ray fluxes in the 2-8 keV band 3 times higher than sources that fall outside the wedge. Their X-ray spectra are also harder. The hardness ratio of the wedge-selected stack is consistent with moderate intrinsic obscuration, but is not suggestive of a highly obscured, Compton-thick source population. It is evident from this comparative study that in order to create a complete

  8. Study Methods to Characterize and Implement Thermography Nondestructive Evaluation (NDE)

    NASA Technical Reports Server (NTRS)

    Walker, James L.

    1998-01-01

    The limits and conditions under which an infrared thermographic nondestructive evaluation can be utilized to assess the quality of aerospace hardware is demonstrated in this research effort. The primary focus of this work is on applying thermography to the inspection of advanced composite structures such as would be found in the International Space Station Instrumentation Racks, Space Shuttle Cargo Bay Doors, Bantam RP-1 tank or RSRM Nose Cone. Here, the detection of delamination, disbond, inclusion and porosity type defects are of primary interest. In addition to composites, an extensive research effort has been initiated to determine how well a thermographic evaluation can detect leaks and disbonds in pressurized metallic systems "i.e. the Space Shuttle Main Engine Nozzles". In either case, research into developing practical inspection procedures was conducted and thermographic inspections were performed on a myriad of test samples, subscale demonstration articles and "simulated" flight hardware. All test samples were fabricated as close to their respective structural counterparts as possible except with intentional defects for NDE qualification. As an added benefit of this effort to create simulated defects, methods were devised for defect fabrication that may be useful in future NDE qualification ventures.

  9. Detection of localized fatigue damage in steel by thermography

    NASA Astrophysics Data System (ADS)

    Medgenberg, Justus; Ummenhofer, Thomas

    2007-04-01

    Fatigue damage of unalloyed steels in the high cycle regime is governed by localized cyclic plastic deformations and subsequent crack initiation. The extent of early microplastic deformations depends on the applied stress level, stress concentration at macroscopic notches, surface treatment, residual stresses etc. The onset of a nonlinear material response can be regarded as an early indicator of fatigue damage. During fatigue loading thermoelastic coupling and thermoplastic dissipation cause characteristic temperature variations in tested specimens which have been assessed by a highly sensitive infrared camera. A specialized data processing method in the time domain has been developed which allows to separate the different contributions to the measured temperature signal. In contrast to other methods - as e.g. measuring the rise of mean temperature during fatigue loading - the proposed methodology is based on measurements during the stabilized temperature regimen and offers very high spatial resolution of localized phenomena. Investigations have been made on mildly notched cylindrical and also on welded specimens. The results confirm the close relation between the local temperature signal and typical fatigue phenomena. The new methodology allows for a much better localization and quantification of effects as cyclic plasticity, crack initiation, crack growth etc. The following paper presents considerations and experimental results of an application of thermography to the local assessment of fatigue damage.

  10. High-frequency heterodyne lock-in thermography (HeLIT): A highly sensitive method to detect early caries

    NASA Astrophysics Data System (ADS)

    Wang, Fei; Liu, Jun-yan; Yang, Jun-han; Oliullah, Md.; Wang, Xiao-chun; Wang, Yang

    2016-10-01

    In this letter, a nonlinear photothermal characteristic of dental tissues has been verified by photothermal radiometry at a given frequency with changing of the laser intensity. Subsequently, the high-frequency heterodyne lock-in thermography (HeLIT) scheme has been introduced to overcome shortages of the low infrared camera frame rate and the poor signal-noise ratio. The smooth surface tooth was artificially demineralized at a different time, and then it was detected by HeLIT, Results illustrated that the phase delay increases with the extension of the demineralized treatment time. The comparison experiments between HeLIT and the homodyne lock-in thermography for detecting artificial caries were carried out. Experimental results illustrated that the HeLIT has the merits of high sensitivity and specificity in detecting early caries.

  11. TACCOS -- A thermography-assisted combustion control system for waste incinerators

    SciTech Connect

    Schuler, F.; Wolfrum, J. . Physikalisch-Chemisches Inst.); Rampp, F.; Martin, J. )

    1994-11-01

    A novel type of combustion control system is described for municipal waste incinerators using infrared thermography to obtain information about the temperature distribution in the furnace interior. A scanner camera operating in the mid infrared was installed at the waste-to-energy plant in Coburg, Germany during the experiments. Selection of an appropriate wavelength region allows the direct imaging of the fuel bed through the overlying flame and flue gas atmosphere and the determination of temperature distributions within seconds. The fast response time of the thermography system compared to shielded thermocouples allows the detection of furnace temperature fluctuations on a short time scale of a few minutes. these data can be used for fine tuning of the total u