Science.gov

Sample records for active power compensation

  1. Reactive power compensating system

    DOEpatents

    Williams, Timothy J.; El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.

    1987-01-01

    The reactive power of an induction machine is compensated by providing fixed capacitors on each phase line for the minimum compensation required, sensing the current on one line at the time its voltage crosses zero to determine the actual compensation required for each phase, and selecting switched capacitors on each line to provide the balance of the compensation required.

  2. New hybrid active power filter for harmonic current suppression and reactive power compensation

    NASA Astrophysics Data System (ADS)

    Biricik, Samet; Cemal Ozerdem, Ozgur; Redif, Soydan; Sezai Dincer, Mustafa

    2016-08-01

    In the case of undistorted and balanced grid voltages, low ratio shunt active power filters (APFs) can give unity power factors and achieve current harmonic cancellation. However, this is not possible when source voltages are distorted and unbalanced. In this study, the cost-effective hybrid active power filter (HAPF) topology for satisfying the requirements of harmonic current suppression and non-active power compensation for industry is presented. An effective strategy is developed to observe the effect of the placement of power capacitors and LC filters with the shunt APF. A new method for alleviating the negative effects of a nonideal grid voltage is proposed that uses a self-tuning filter algorithm with instantaneous reactive power theory. The real-time control of the studied system was achieved with a field-programmable gate array (FPGA) architecture, which was developed using the OPAL-RT system. The performance result of the proposed HAPF system is tested and presented under nonideal supply voltage conditions.

  3. Reactive Power Compensator.

    DOEpatents

    El-Sharkawi, M.A.; Venkata, S.S.; Chen, M.; Andexler, G.; Huang, T.

    1992-07-28

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation. 26 figs.

  4. Reactive power compensator

    DOEpatents

    El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

    1992-01-01

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

  5. Actively compensation of low order aberrations by refractive shaping system for high power slab lasers

    NASA Astrophysics Data System (ADS)

    Xue, Zheng-wei; Guo, Ya-ding; Chen, Zhong-zheng; Li, Shuai; Xu, Yi-ting; Xu, Jian; Wang, Bao-shan; Gong, Ke-ling; Gao, Hong-wei; Bo, Yong; Peng, Qin-jun; Cui, Da-fu; Xu, Zu-yan

    2015-12-01

    We present a compact refractive shaping system for actively compensating low order aberrations of high power slab lasers. The shaping system includes three spherical lenses and two cylindrical lenses. Both theoretical and experimental investigations were performed to evaluate the compensation capability of the refractive shaping system. For a typical input beam with large low order aberrations of peak-to-valley (PV)=66.10λ and root-mean-square (RMS)=16.05λ, adjusting the distance between lenses, the wavefront aberrations are reduced to PV=0.48λ, RMS=0.10λ for the theoretical simulation and PV=0.50λ, RMS=0.11λ for the experimental result, respectively. It indicates that the main low order aberrations of defocus and 0° astigmatism can be significantly compensated by actively adjusting the distance between lenses and the experimental result agree well with the theoretical simulation.

  6. Photovoltaic solar system connected to the electric power grid operating as active power generator and reactive power compensator

    SciTech Connect

    Albuquerque, Fabio L.; Moraes, Adelio J.; Guimaraes, Geraldo C.; Sanhueza, Sergio M.R.; Vaz, Alexandre R.

    2010-07-15

    In the case of photovoltaic (PV) systems acting as distributed generation (DG) systems, the DC energy that is produced is fed to the grid through the power-conditioning unit (inverter). The majority of contemporary inverters used in DG systems are current source inverters (CSI) operating at unity power factor. If, however, we assume that voltage source inverters (VSI) can replace CSIs, we can generate reactive power proportionally to the remaining unused capacity at any given time. According to the theory of instantaneous power, the inverter reactive power can be regulated by changing the amplitude of its output voltage. In addition, the inverter active power can be adjusted by modifying the phase angle of its output voltage. Based on such theory, both the active power supply and the reactive power compensation (RPC) can be carried out simultaneously. When the insolation is weak or the PV modules are inoperative at night, the RPC feature of a PV system can still be used to improve the inverter utilisation factor. Some MATLAB simulation results are included here to show the feasibility of the method. (author)

  7. Reactive Power Compensating System.

    DOEpatents

    Williams, Timothy J.; El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.

    1985-01-04

    The circuit was designed for the specific application of wind-driven induction generators. It has great potential for application in any situation where a varying reactive power load is present, such as with induction motors or generators, or for transmission network compensation.

  8. An advanced static var compensator based on a three level IGBT inverter modelling analysis and active power filtering

    NASA Astrophysics Data System (ADS)

    Draou, Azeddine

    2012-12-01

    This paper presents the dynamic performance analysis of an Advanced Static Var Compensator (ASVC) using three-level neutral point-clamped voltage source inverter. The paper presents the principles of operating and the method of reference currents generation. The dynamic behaviour of the system is further analysed using Matlab/Simulink with SimPower Systems toolbox through a set of simulation tests. The results obtained have been applied to an active power filter which might lead to the design of a robust controller for current harmonics and reactive power applications

  9. Photovoltaic power converter system with a controller configured to actively compensate load harmonics

    DOEpatents

    de Rooij, Michael Andrew; Steigerwald, Robert Louis; Delgado, Eladio Clemente

    2008-12-16

    Photovoltaic power converter system including a controller configured to reduce load harmonics is provided. The system comprises a photovoltaic array and an inverter electrically coupled to the array to generate an output current for energizing a load connected to the inverter and to a mains grid supply voltage. The system further comprises a controller including a first circuit coupled to receive a load current to measure a harmonic current in the load current. The controller includes a second circuit to generate a fundamental reference drawn by the load. The controller further includes a third circuit for combining the measured harmonic current and the fundamental reference to generate a command output signal for generating the output current for energizing the load connected to the inverter. The photovoltaic system may be configured to compensate harmonic currents that may be drawn by the load.

  10. Influence of a voltage compensation type active superconducting fault current limiter on the transient stability of power system

    NASA Astrophysics Data System (ADS)

    Chen, L.; Tang, Y. J.; Shi, J.; Chen, N.; Song, M.; Cheng, S. J.; Hu, Y.; Chen, X. S.

    2009-10-01

    We have proposed a voltage compensation type active superconducting fault current limiter (SFCL). In this paper, the influence of the SFCL on the transient stability of power system is investigated. For the typical one-machine infinite-bus system, the power-angle characteristics of generator with SFCL are studied in different working conditions, and the transient physical process is analyzed. Using MATLAB SIMULINK, the power-angle swing curves are simulated under different current-limiting modes, fault types and fault clearance times. The results show that the proposed SFCL can effectively reduce the transient swing amplitude of rotor and extend the critical clearance time under mode 1, compared with mode 2 and mode 3 having few effects on enhancing the transient stability.

  11. Multipurpose active/passive motion compensation system

    SciTech Connect

    Sullivan, R.A.; Clements, R.E.; Davenport, M.R.

    1984-05-01

    A microprocessor-controlled active/passive motion compensation system has been developed for deploying a variety of geotechnical in-situ testing devices with mobile drilling rigs from low-cost service vessels. The light-weight rotary heave compensator incorporates a hydraulic motor as the compensator actuator and a servo-controlled closed loop pump to reduce the air storage and power requirements. Unique features of the system are the use of inertial sensors to measure three components of boat motion, the ability to run the system in active/passive or passive modes, and the ability to automatically lower the drillstring at a constant velocity while maintaining motion compensation. Quantitative measurements made during sea trials offshore California yielded motion compensation accuracy approaching 98 percent which is much better than the compensation achieved with passive systems. Results are presented from offshore in-situ testing with a cone penetrometer, a vane shear device, and a suspension PS logger. The system can also be used for other offshore applications.

  12. Static var compensators stabilize power voltages

    SciTech Connect

    Burch, R.

    1996-06-01

    This article discusses the operation of a static var compensator as installed by Alabama Power near a steel mill with a large arc furnace load. This is expected to result in a number of benefits, including flicker reduction, dynamic power factor correction, harmonics filtering and a reduction in system losses.

  13. Power Compensation for ICRF Heating in EAST

    NASA Astrophysics Data System (ADS)

    Chen, Gen; Qin, Chengming; Mao, Yuzhou; Zhao, Yanping; Yuan, Shuai; Zhang, Xinjun

    2016-08-01

    The source system covering a working frequency range of 24 MHz to 70 MHz with a total maximum output power of 12 MW has already been fabricated for Ion Cyclotron Range of Frequency (ICRF) heating in EAST from 2012. There are two continuous wave (CW) antennas consisting of four launching elements each fed by a separate 1.5 MW transmitter. Due to the strong mutual coupling among the launching elements, the injection power for launching elements should be imbalance to keep the k‖ (parallel wave number) spectrum of the launcher symmetric for ICRF heating. Cross power induced by the mutual coupling will also induce many significant issues, such as an uncontrollable phase of currents in launching elements, high voltage standing wave ratio (VSWR), and impedance mismatching. It is necessary to develop a power compensation system for antennas to keep the power balance between the feed points. The power balance system consists of two significant parts: a decoupler and phase control. The decoupler helps to achieve ports isolation to make the differential phase controllable and compensate partly cross power. After that, the differential phase of 0 or π will keep the power balance of two feed points completely. The first power compensation system consisting of four decouplers was assembled and tested for the port B antenna at the working frequency of 35 MHz. With the application of the power compensation system, the power balance, phase feedback control, and voltage standing wave ratio (VSWR) had obviously been improved in the 2015 EAST campaign. supported by the National Magnetic Confinement Fusion Science Program of China (No. 2015GB101001) and National Natural Science Foundation of China (Nos. 11575237, 11375235, 11375236)

  14. Gamma compensated, self powered neutron detector

    DOEpatents

    Brown, Donald P.

    1977-01-01

    An improved, self-powered, gamma compensated, neutron detector having two electrically conductive concentric cylindrical electrodes and a central rod emitter formed from a material which emits beta particles when bombarded by neutrons. The outer electrode and emitter are maintained at a common potential and the neutron representative current is furnished at the inner cylindrical electrode which serves as a collector. The two concentric cylindrical electrodes are designed to exhibit substantially equal electron emission induced by Compton scattering under neutron bombardment to supply the desired gamma compensation.

  15. Static reactive power compensators for high-voltage power systems. Final report

    SciTech Connect

    Not Available

    1981-04-01

    A study conducted to summarize the role of static reactive power compensators for high voltage power system applications is described. This information should be useful to the utility system planning engineer in applying static var systems (SVS) to high voltage as (HVAC) systems. The static var system is defined as a form of reactive power compensator. The general need for reactive power compensation in HVAC systems is discussed, and the static var system is compared to other devices utilized to provide reactive power compensation. Examples are presented of applying SVS for specific functions, such as the prevention of voltage collapse. The operating principles of commercially available SVS's are discussed in detail. The perormance and active power loss characteristics of SVS types are compared.

  16. Voltage and Current Unbalance Compensation Using a Parallel Active Filter

    SciTech Connect

    Xu, Yan; Tolbert, Leon M; Kueck, John D; Rizy, D Tom

    2007-01-01

    A three-phase insulated gate bipolar transistor (IGBT)-based parallel active filter is used for current and/or voltage unbalance compensation. An instantaneous power theory is adopted for real-time calculation and control. Three control schemes, current control, voltage control, and integrated control are proposed to compensate the unbalance of current, voltage, or both. The compensation results of the different control schemes in unbalance cases (load unbalance or voltage source unbalance) are compared and analyzed. The simulation and experimental results show that the control schemes can compensate the unbalance in load current or in the voltage source. Different compensation objectives can be achieved, i.e., balanced and unity power factor source current, balanced and regulated voltage, or both, by choosing appropriate control schemes.

  17. Advanced configuration of hybrid passive filter for reactive power and harmonic compensation.

    PubMed

    Kececioglu, O Fatih; Acikgoz, Hakan; Sekkeli, Mustafa

    2016-01-01

    Harmonics is one of the major power quality problems for power systems. The harmonics can be eliminated by power filters such as passive, active, and hybrid. In this study, a new passive filter configuration has been improved in addition to the existing passive filter configurations. Conventional hybrid passive filters are not successful to compensate rapidly changing reactive power demand. The proposed configure are capable of compensating both harmonics and reactive power at the same time. Simulation results show that performance of reactive power and harmonic compensation with advanced hybrid passive filter is better than conventional hybrid passive filters. PMID:27536512

  18. Unbalance vibratory displacement compensation for active magnetic bearings

    NASA Astrophysics Data System (ADS)

    Gao, Hui; Xu, Longxiang; Zhu, Yili

    2013-01-01

    As the dynamic stiffness of radial magnetic bearings is not big enough, when the rotor spins at high speed, unbalance displacement vibration phenomenon will be produced. The most effective way for reducing the displacement vibration is to enhance the radial magnetic bearing stiffness through increasing the control currents, but the suitable control currents are not easy to be provided, especially, to be provided in real time. To implement real time unbalance displacement vibration compensation, through analyzing active magnetic bearings (AMB) mathematical model, the existence of radial displacement runout is demonstrated. To restrain the runout, a new control scheme-adaptive iterative learning control (AILC) is proposed in view of rotor frequency periodic uncertainties during the startup process. The previous error signal is added into AILC learning law to enhance the convergence speed, and an impacting factor β influenced by the rotor rotating frequency is introduced as learning output coefficient to improve the rotor control effects. As a feed-forward compensation controller, AILC can provide one unknown and perfect compensatory signal to make the rotor rotate around its geometric axis through power amplifier and radial magnetic bearings. To improve AMB closed-loop control system robust stability, one kind of incomplete differential PID feedback controller is adopted. The correctness of the AILC algorithm is validated by the simulation of AMB mathematical model adding AILC compensation algorithm through MATLAB soft. And the compensation for fixed rotational frequency is implemented in the actual AMB system. The simulation and experiment results show that the compensation scheme based on AILC algorithm as feed-forward compensation and PID algorithm as close-loop control can realize AMB system displacement minimum compensation at one fixed frequency, and improve the stability of the control system. The proposed research provides a new adaptive iterative learning

  19. Risk compensation behaviours in construction workers' activities.

    PubMed

    Feng, Yingbin; Wu, Peng

    2015-01-01

    The purpose of this study was to test whether the construction workers have the tendency of engaging in risk compensation behaviours, and identify the demographic variables, which may influence the extent to which the construction workers may show risk compensation behaviours. Both quantitative (survey) and qualitative (interviews) approaches were used in this study. A questionnaire survey was conducted with all the construction workers on three building construction sites of a leading construction company in Australia. Semi-structured interviews were then conducted to validate the findings of the quantitative research. The findings indicate that workers tend to show risk compensation behaviours in the construction environment. The workers with more working experience, higher education, or having never been injured at work before have a higher tendency to show risk compensation in their activities than the others. The implication is that contractors need to assess the potential influence of workers' risk compensation behaviours when evaluating the effect of risk control measures. It is recommended that supervisors pay more attention to the behavioural changes of those workers who have more experience, higher education, and have never been injured before after the implementation of new safety control measures on construction site. PMID:24134314

  20. Active Wireline Heave Compensation for Ocean Drilling

    NASA Astrophysics Data System (ADS)

    Goldberg, D.; Liu, T.; Swain, K.; Furman, C.; Iturrino, G. J.

    2014-12-01

    The up-and-down heave motion of a ship causes a similar motion on any instruments tethered on wireline cable below it. If the amplitude of this motion is greater than a few tens of cm, significant discrepancy in the depth below the ship is introduced, causing uncertainty in the acquired data. Large and irregular cabled motions also increase the risk of damaging tethered instruments, particularly those with relatively delicate sensors. In 2005, Schlumberger and Deep Down, Inc built an active wireline heave compensator (AHC) system for use onboard the JOIDES Resolution to compensate for heave motion on wireline logging tools deployed in scientific drill holes. The goals for the new AHC system were to (1) design a reliable heave compensation system; and (2) devise a robust and quantitative methodology for routine assessment of compensation efficiency (CE) during wireline operations. Software programs were developed to monitor CE and the dynamics of logging tools in real-time, including system performance under variable parameters such as water depth, sea state, cable length, logging speed and direction. We present the CE results from the AHC system on the JOIDES Resolution during a 5-year period of recent IODP operations and compare the results to those from previous compensation systems deployed during ODP and IODP. Based on new data under heave conditions of ±0.2-2.0 m and water depths of 300-4,800 m in open holes, the system reduces 65-80% of downhole tool displacement under stationary conditions and 50-60% during normal logging operations. Moreover, down/up tool motion at low speeds (300-600 m/h) reduces the system's CE values by 15-20%, and logging down at higher speeds (1,000-1,200 m/h) reduces CE values by 55-65%. Furthermore, the system yields slightly lower CE values of 40-50% without tension feedback of the downhole cable while logging. These results indicate that the new system's compensation efficiency is comparable to or better than previous systems

  1. Switched filter for the compensation of power processors

    SciTech Connect

    Maranesi, P.; Pinola, L. ); Varoli, V. )

    1990-07-01

    An analog-amplitude discrete-time recursive filter is proposed for the frequency compensation of power processors. It has been applied to a Cuk converter, and it was allowed to reach an almost ideal profile of G{sub loop}. The filter copes with converters that chop up to 0.5 MHz and seems to be better than time-invariant compensation networks and DSP-based filters. Exact small-signal analysis of the switching cell and of the compensation filter is carried out, and experimental results of gain and phase frequency dependencies are reported.

  2. 75 FR 30812 - Frequency Regulation Compensation in the Organized Wholesale Power Markets; Further Notice...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-02

    ... Organized Wholesale Power Markets, 75 FR 23,759, as supplemented by Supplemental Notice of Technical... Energy Regulatory Commission Frequency Regulation Compensation in the Organized Wholesale Power Markets... of Proposed Rulemaking on Frequency Regulation Compensation in the Organized Wholesale Power...

  3. Optimized Reactive Power Compensation Using Fuzzy Logic Controller

    NASA Astrophysics Data System (ADS)

    George, S.; Mini, K. N.; Supriya, K.

    2015-03-01

    Reactive power flow in a long transmission line plays a vital role in power transfer capability and voltage stability in power system. Traditionally, shunt connected compensators are used to control reactive power in long transmission line. Thyristor controlled reactor is used to control reactive power under lightly loaded condition. By controlling firing angle of thyristor, it is possible to control reactive power in the transmission lines. However, thyristor controlled reactor will inject harmonic current into the system. An attempt to reduce reactive power injection will increase harmonic distortion in the line current and vice versa. Thus, there is a trade-off between reactive power injection and harmonics in current. By optimally controlling the reactive power injection, harmonics in current can be brought within the specified limit. In this paper, a Fuzzy Logic Controller is implemented to obtain optimal control of reactive power of the compensator to maintain voltage and harmonic in current within the limits. An algorithm which optimizes the firing angle in each fuzzy subset by calculating the rank of feasible firing angles is proposed for the construction of rules in Fuzzy Logic Controller. The novelty of the algorithm is that it uses a simple error formula for the calculation of the rank of the feasible firing angles in each fuzzy subset.

  4. Assessment of the Economic Benefits from Reactive Power Compensation

    SciTech Connect

    Li, Fangxing; Kueck, John D; Rizy, D Tom; Tolbert, Leon M; Zhang, Wenjuan

    2006-01-01

    The U.S. power industry is under great pressure to provide reactive power or Var support. Although it is generally known that there are technical benefits for utilities and industrial customers to provide local reactive power support, a thorough quantitative investigation of the economic benefit is greatly needed. This paper seeks to provide a quantitative approach to evaluate the benefits from local reactive power compensation. This paper investigates the benefits including reduced losses, shifting reactive power flow to real power flow, and increased transfer capability. These benefits are illustrated with a simple two-bus model and then presented with a more complicated model using Optimal Power Flow. Tests are conducted on a system with seven buses in two areas. These simulations show that the economic benefits can be significant, if compared with capacity payment to central generators or power factor penalties applied to utilities. This economic value may give utilities a better understanding of the Var benefits to assist their cost-benefit analysis for Var compensation. In addition, since the economic benefits are significant, this paper suggests that the future reactive power market should consider local Var providers.

  5. Compensating for Tissue Changes in an Ultrasonic Power Link for Implanted Medical Devices.

    PubMed

    Vihvelin, Hugo; Leadbetter, Jeff; Bance, Manohar; Brown, Jeremy A; Adamson, Robert B A

    2016-04-01

    Ultrasonic power transfer using piezoelectric devices is a promising wireless power transfer technology for biomedical implants. However, for sub-dermal implants where the separation between the transmitter and receiver is on the order of several acoustic wavelengths, the ultrasonic power transfer efficiency (PTE) is highly sensitive to the distance between the transmitter and receiver. This sensitivity can cause large swings in efficiency and presents a serious limitation on battery life and overall performance. A practical ultrasonic transcutaneous energy transfer (UTET) system design must accommodate different implant depths and unpredictable acoustic changes caused by tissue growth, hydration, ambient temperature, and movement. This paper describes a method used to compensate for acoustic separation distance by varying the transmit (Tx) frequency in a UTET system. In a benchtop UTET system we experimentally show that without compensation, power transfer efficiency can range from 9% to 25% as a 5 mm porcine tissue sample is manipulated to simulate in situ implant conditions. Using an active frequency compensation method, we show that the power transfer efficiency can be kept uniformly high, ranging from 20% to 27%. The frequency compensation strategy we propose is low-power, non-invasive, and uses only transmit-side measurements, making it suitable for active implanted medical device applications. PMID:26054073

  6. Index-based reactive power compensation scheme for voltage regulation

    NASA Astrophysics Data System (ADS)

    Dike, Damian Obioma

    2008-10-01

    Increasing demand for electrical power arising from deregulation and the restrictions posed to the construction of new transmission lines by environment, socioeconomic, and political issues had led to higher grid loading. Consequently, voltage instability has become a major concern, and reactive power support is vital to enhance transmission grid performance. Improved reactive power support to distressed grid is possible through the application of relatively unfamiliar emerging technologies of "Flexible AC Transmission Systems (FACTS)" devices and "Distributed Energy Resources (DERS)." In addition to these infrastructure issues, a lack of situational awareness by system operators can cause major power outages as evidenced by the August 14, 2003 widespread North American blackout. This and many other recent major outages have highlighted the inadequacies of existing power system indexes. In this work, a novel "Index-based reactive compensation scheme" appropriate for both on-line and off-line computation of grid status has been developed. A new voltage stability index (Ls-index) suitable for long transmission lines was developed, simulated, and compared to the existing two-machine modeled L-index. This showed the effect of long distance power wheeling amongst regional transmission organizations. The dissertation further provided models for index modulated voltage source converters (VSC) and index-based load flow analysis of both FACTS and microgrid interconnected power systems using the Newton-Raphson's load flow model incorporated with multi-FACTS devices. The developed package has been made user-friendly through the embodiment of interactive graphical user interface and implemented on the IEEE 14, 30, and 300 bus systems. The results showed reactive compensation has system wide-effect, provided readily accessible system status indicators, ensured seamless DERs interconnection through new islanding modes and enhanced VSC utilization. These outcomes may contribute

  7. Conjugate field approaches for active array compensation

    NASA Technical Reports Server (NTRS)

    Acosta, R. J.

    1989-01-01

    Two approaches for calculating the compensating feed array complex excitations are namely, the indirect conjugate field matching (ICFM) and the direct conjugate field matching (DCFM) approach. In the ICFM approach the compensating feed array excitations are determined by considering the transmitting mode and the reciprocity principle. The DCF, in contrast calculates the array excitations by integrating directly the induced surface currents on the reflector under a receiving mode. DCFM allows the reflector to be illuminated by an incident plane wave with a tapered amplitude. The level of taper can effectively control the sidelobe level of the compensated antenna pattern. Both approaches are examined briefly.

  8. Wind plant interaction with series-compensated power systems

    NASA Astrophysics Data System (ADS)

    Ramamurthy, Jayanth R.

    Wind power based generation has been rapidly growing world-wide during the recent past. In order to transmit large amounts of wind power over long distances, system planners may often add series compensation to existing transmission lines owing to several benefits such as improved steady-state power transfer limit, improved transient stability, and efficient utilization of transmission infrastructure. Application of series capacitors has posed resonant interaction concerns such as through subsynchronous resonance (SSR) with conventional turbine-generators. Wind turbine-generators may also be susceptible to such resonant interactions. However, not much information is available in literature and even engineering standards are yet to address these issues. The motivation problem for this research is based on an actual system switching event that resulted in undamped oscillations in a 345-kV series-compensated, typical ring-bus power system configuration. Based on time-domain ATP (Alternative Transients Program) modeling, simulations and analysis of system event records, the occurrence of subsynchronous interactions within the existing 345-kV series-compensated power system has been investigated. Effects of various small-signal and large-signal power system disturbances with both identical and non-identical wind turbine parameters (such as with a statistical-spread) has been evaluated. Effect of parameter variations on subsynchronous oscillations has been quantified using 3D-DFT plots and the oscillations have been identified as due to electrical self-excitation effects, rather than torsional interaction. Further, the generator no-load reactance and the rotor-side converter inner-loop controller gains have been identified as bearing maximum sensitivity to either damping or exacerbating the self-excited oscillations. A higher-order spectral analysis method based on modified Prony estimation has been successfully applied to the field records identifying dominant 9.79 Hz

  9. Noise power spectrum measurements under nonuniform gains and their compensations

    NASA Astrophysics Data System (ADS)

    Kim, Dong Sik; Kim, Eun; Shin, Choul Woo

    2016-03-01

    The fixed pattern noise, which is due to the nonuniform amplifier gains and scintillator sensitivities, should be alleviated in radiography imaging and should have less influence on measuring the noise power spectrum (NPS) of the radiography detector. In order to reduce the influence, background trend removing methods, which are based on low-pass filtering, polynomial fitting, and subtracting the average image of the uniform exposure images, are traditionally employed in the literature. In terms of removing the fixed pattern noise, the subtraction method shows a good performance. However, the number of images to be averaged is practically finite and thus the noise contained in the average image contaminates the image difference and inflates the NPS curve. In this paper, an image formation model considering the nonuniform gain is constructed and two measuring methods, which are based on the subtraction and gain correction, respectively, are considered. In order to accurately measure a normalized NPS (NNPS) in the measuring methods, the number of images to be averaged is considered for NNPS compensations. For several flat-panel radiography detectors, the NNPS measurements are conducted and compared with conventional approaches, which have no compensation stages. Through experiments it is shown that the compensation can provide accurate NNPS measurements less influenced by the fixed pattern noise.

  10. Drag-compensated, precision-powered hinge system

    NASA Technical Reports Server (NTRS)

    Jacquemin, G. G.; Rusk, S. J.

    1985-01-01

    The design of a high precision powered hinge is complicated by the unavoidable presence of parasitic drag torque resulting mainly from friction and transfer of power, signals, and fluids across the hinge. Regardless of the type of drive system selected, it is impossible to completely eliminate all parasitic drag. However, the mechanism described here comes very close to providing a drag free system. All sources of parasitic drag torque are collected on a shaft which is powered by an electric motor independent of the main hinge drive. Under control of a sensor, the electric motor applies a compensating torque equal to that of the parasitic drag torque, allowing the main hinge drive to operate in a practically drag free environment with very high positioning precision.

  11. Enhanced Electric Power Transmission by Hybrid Compensation Technique

    NASA Astrophysics Data System (ADS)

    Palanichamy, C.; Kiu, G. Q.

    2015-04-01

    In today's competitive environment, new power system engineers are likely to contribute immediately to the task, without years of seasoning via on-the-job training, mentoring, and rotation assignments. At the same time it is becoming obligatory to train power system engineering graduates for an increasingly quality-minded corporate environment. In order to achieve this, there is a need to make available better-quality tools for educating and training power system engineering students and in-service system engineers too. As a result of the swift advances in computer hardware and software, many windows-based computer software packages were developed for the purpose of educating and training. In line with those packages, a simulation package called Hybrid Series-Shunt Compensators (HSSC) has been developed and presented in this paper for educational purposes.

  12. 75 FR 23759 - Frequency Regulation Compensation in the Organized Wholesale Power Markets; Notice of Technical...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-04

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Frequency Regulation Compensation in the Organized Wholesale Power... technical conference to elicit input on issues pertaining to Frequency Regulation Compensation in the...

  13. High power single-frequency and frequency-doubled laser with active compensation for the thermal lens effect of terbium gallium garnet crystal.

    PubMed

    Yin, Qiwei; Lu, Huadong; Su, Jing; Peng, Kunchi

    2016-05-01

    The thermal lens effect of terbium gallium garnet (TGG) crystal in a high power single-frequency laser severely limits the output power and the beam quality of the laser. By inserting a potassium dideuterium phosphate (DKDP) slice with negative thermo-optical coefficient into the laser resonator, the harmful influence of the thermal lens effect of the TGG crystal can be effectively mitigated. Using this method, the stable range of the laser is broadened, the bistability phenomenon of the laser during the process of changing the pump power is completely eliminated, the highest output power of an all-solid-state continuous-wave intracavity-frequency-doubling single-frequency laser at 532 nm is enhanced to 30.2 W, and the beam quality of the laser is significantly improved. PMID:27128067

  14. A Pulsed Power Supply with Sag Compensation using Controlled Gradational Voltage

    NASA Astrophysics Data System (ADS)

    Suzuki, Akihiro; Yamada, Masaki; Tashiro, Shojirou; Iwata, Akihiko

    A pulsed power supply with sag compensation using controlled gradational voltage to increase the flatness of output waveforms has been developed.The sag compensation circuit consists of compensation units connected in series. Each compensation unit consists of capacitances, diodes, and semiconductor switches. The capacitances of each unit are charged with different voltages by 2n (V0, 2V0, 4V0, ···). The compensation voltages, which has 2n-1 steps, is generated by switching the semiconductor switches of each unit in a binary sequence. Using this method, compensation voltage waveforms up to 6.2kV with 31 steps can be obtained with 5 compensation units. The sag compensation circuit has been adapted to a direct switch type pulsed power supply, which generates 7kV pulsed voltage with a pulse width of 700μs, thus realizing sag compensation.

  15. Calculating activation energies for temperature compensation in circadian rhythms

    NASA Astrophysics Data System (ADS)

    Bodenstein, C.; Heiland, I.; Schuster, S.

    2011-10-01

    Many biological species possess a circadian clock, which helps them anticipate daily variations in the environment. In the absence of external stimuli, the rhythm persists autonomously with a period of approximately 24 h. However, single pulses of light, nutrients, chemicals or temperature can shift the clock phase. In the case of light- and temperature-cycles, this allows entrainment of the clock to cycles of exactly 24 h. Circadian clocks have the remarkable property of temperature compensation, that is, the period of the circadian rhythm remains relatively constant within a physiological range of temperatures. For several organisms, temperature-regulated processes within the circadian clock have been identified in recent years. However, how these processes contribute to temperature compensation is not fully understood. Here, we theoretically investigate temperature compensation in general oscillatory systems. It is known that every oscillator can be locally temperature compensated around a reference temperature, if reactions are appropriately balanced. A balancing is always possible if the control coefficient with respect to the oscillation period of at least one reaction in the oscillator network is positive. However, for global temperature compensation, the whole physiological temperature range is relevant. Here, we use an approach which leads to an optimization problem subject to the local balancing principle. We use this approach to analyse different circadian clock models proposed in the literature and calculate activation energies that lead to temperature compensation.

  16. Active damping and compensation of satellite appendages

    NASA Astrophysics Data System (ADS)

    Charon, W.; Baier, H.

    1993-10-01

    Future space missions will employ large and, for lightweight reasons, extremely flexible structures with very high performance requirements such as high pointing accuracy and stability, and high shape precision. This requires actively damping out vibrations induced by spacecraft maneuvers. The damping of the solar array vibrations is a characteristic task for such active interface devices. The example of an active interface for damping the bending vibrations of large conventional solar arrays is addressed. Other typical active components are active tube sections for damping the vibrations of large booms, and interfaces between satellite and vibrating large masts carrying high precision reflectors or measurement systems. The mechanical properties of the interfaces and the technological requirements related to their development are determined. New 'smart' materials are prominent among current concerns. Piezoelectric polymer foils bonded to structural shell surfaces, embedded thin piezoceramics plates, and embedded fiber optics sensors, as well as the implementation of materials such as memory alloys, are here addressed.

  17. Compensation for Harmonic Currents and Reactive Power in Wind Power Generation System using PWM Inverter

    NASA Astrophysics Data System (ADS)

    Shinohara, Katsuji; Shinhatsubo, Kurato; Iimori, Kenichi; Yamamoto, Kichiro; Saruban, Takamichi; Yamaemori, Takahiro

    In recent year, consciousness of environmental problems is enhancing, and the price of the electric power purchased by an electric power company is established expensive for the power plant utilizing the natural energy. So, the introduction of the wind power generation is promoted in Japan. Generally, squirrel-cage induction machines are widely used as a generator in wind power generation system because of its small size, lightweight and low-cost. However, the induction machines do not have a source of excitation. Thus, it causes the inrush currents and the instantaneous voltage drop when the generator is directly connected to a power grid. To reduce the inrush currents, an AC power regulator is used. Wind power generations are frequently connected to and disconnected from the power grid. However, when the inrush currents are reduced, harmonic currents are caused by phase control of the AC power regulator. And the phase control of AC power regulator cannot control the power factor. Therefore, we propose the use of the AC power regulator to compensate for the harmonic currents and reactive power in the wind power generation system, and demonstrate the validity of its system by simulated and experimental results.

  18. 75 FR 31430 - Frequency Regulation Compensation in the Organized Wholesale Power Markets; Notice Establishing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-03

    ... Markets, 75 FR 23,759, as supplemented by Supplemental Notice of Technical Conference re Frequency... Energy Regulatory Commission Frequency Regulation Compensation in the Organized Wholesale Power Markets... technical conference regarding frequency regulation in the organized wholesale power markets, as...

  19. Design of active temperature compensated composite free-free beam MEMS resonators in a standard process

    NASA Astrophysics Data System (ADS)

    Xereas, George; Chodavarapu, Vamsy P.

    2014-03-01

    Frequency references are used in almost every modern electronic device including mobile phones, personal computers, and scientific and medical instrumentation. With modern consumer mobile devices imposing stringent requirements of low cost, low complexity, compact system integration and low power consumption, there has been significant interest to develop batch-manufactured MEMS resonators. An important challenge for MEMS resonators is to match the frequency and temperature stability of quartz resonators. We present 1MHz and 20MHz temperature compensated Free-Free beam MEMS resonators developed using PolyMUMPS, which is a commercial multi-user process available from MEMSCAP. We introduce a novel temperature compensation technique that enables high frequency stability over a wide temperature range. We used three strategies: passive compensation by using a structural gold (Au) layer on the resonator, active compensation through using a heater element, and a Free-Free beam design that minimizes the effects of thermal mismatch between the vibrating structure and the substrate. Detailed electro-mechanical simulations were performed to evaluate the frequency response and Quality Factor (Q). Specifically, for the 20MHz device, a Q of 10,000 was obtained for the passive compensated design. Finite Element Modeling (FEM) simulations were used to evaluate the Temperature Coefficient of frequency (TCf) of the resonators between -50°C and 125°C which yielded +0.638 ppm/°C for the active compensated, compared to -1.66 ppm/°C for the passively compensated design and -8.48 ppm/°C for uncompensated design for the 20MHz device. Electro-thermo-mechanical simulations showed that the heater element was capable of increasing the temperature of the resonators by approximately 53°C with an applied voltage of 10V and power consumption of 8.42 mW.

  20. Linear signal-compensated amplifier for reactor power measuring channels

    SciTech Connect

    Khaleeq, M. Tahir; Atique-ur-Rahman,; Ahmed, Eijaz

    2006-07-15

    A linear amplifier with automatic signal compensation has been developed for nuclear channels. The amplifier controls its sensitivity automatically according to the reference input within the desired settings and has automatic signal compensation capability for use in the nuclear channels. The amplifier will be used in the existing safety channel of Pakistan Research Reactor-1, where the system has an independent sensitivity control unit for manual compensation of xenon effect. The new amplifier will improve the safety of the system. The amplifier is tested and the results found are in very good agreement with the designed specifications. This article presents design and construction of the amplifier and test results.

  1. Linear signal-compensated amplifier for reactor power measuring channels

    NASA Astrophysics Data System (ADS)

    Khaleeq, M. Tahir; Atique-ur-Rahman, Ahmed, Eijaz

    2006-07-01

    A linear amplifier with automatic signal compensation has been developed for nuclear channels. The amplifier controls its sensitivity automatically according to the reference input within the desired settings and has automatic signal compensation capability for use in the nuclear channels. The amplifier will be used in the existing safety channel of Pakistan Research Reactor-1, where the system has an independent sensitivity control unit for manual compensation of xenon effect. The new amplifier will improve the safety of the system. The amplifier is tested and the results found are in very good agreement with the designed specifications. This article presents design and construction of the amplifier and test results.

  2. 75 FR 26225 - Frequency Regulation Compensation in the Organized Wholesale Power Markets; Notice of Technical...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-11

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Frequency Regulation Compensation in the Organized Wholesale Power Markets... conference to elicit input on issues pertaining to Frequency Regulation Compensation in the ISO/RTO...

  3. Application of VSC-HVDC with Shunt Connected SMES for Compensation of Power Fluctuation

    NASA Astrophysics Data System (ADS)

    Linn, Zarchi; Kakigano, Hiroaki; Miura, Yushi; Ise, Toshifumi

    This paper describes the application of VSC-HVDC (High Voltage DC Transmission using Voltage Source Converter) with shunt connected SMES (Superconducting Magnetic Energy Storage) for compensation of power fluctuation caused by fluctuating power source such as photovoltaics and wind turbines. The objectives of this proposed system is to smooth out fluctuating power in one terminal side of HVDC in order to avoid causing power system instability and frequency deviation by absorbing or providing power according to the system requirement while another terminal side power is fluctuated. The shunt connected SMES charges and discharges the energy to and from the dc side and it compensates required power of fluctuation to obtain constant power flow in one terminal side of VSC-HVDC system. This system configuration has ability for power system stabilization in the case of power fluctuation from natural energy source. PSCAD/EMTDC simulation is used to evaluate the performance of applied system configuration and control method.

  4. Compensation for thermally induced birefringence in polycrystalline ceramic active elements

    SciTech Connect

    Kagan, M A; Khazanov, E A

    2003-10-31

    Polycrystalline ceramics differ significantly from single crystals in that the crystallographic axes (and hence of the axes of thermally induced birefringence) are oriented randomly in each granule of the ceramic. The quaternion formalism is employed to calculate the depolarisation in the ceramics and the efficiency of its compensation. The obtained analytic expressions are in good agreement with the numerical relations. It is shown that the larger the ratio of the sample length to the granule size, the closer the properties of the ceramics to those of a single crystal with the [111] orientation (in particular, the uncompensated depolarisation is inversely proportional to this ratio). (active media)

  5. 75 FR 15495 - Agency Information Collection (Compensation and Pension Examination Program (CPEP)) Activities...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-29

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF VETERANS AFFAIRS Agency Information Collection (Compensation and Pension Examination Program (CPEP)) Activities... (CPEP).'' SUPPLEMENTARY INFORMATION: Title: Compensation and Pension Examination Program (CPEP)...

  6. 78 FR 6848 - Agency Information Collection (Compensation and Pension Examination Program) Activities Under OMB...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-31

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF VETERANS AFFAIRS Agency Information Collection (Compensation and Pension Examination Program) Activities Under OMB....'' SUPPLEMENTARY INFORMATION: Title: Compensation and Pension Examination Program (CPEP) Veterans...

  7. Active Heave-Compensated Coring On The New Jersey Shelf

    NASA Astrophysics Data System (ADS)

    Nielson, D. L.; Pardey, M.; Austin, J. A.; Goff, J. A.; Alexander, C.; Christensen, B. A.; Gulick, S. P.; Fulthorpe, C. S.; Nordfjord, S.; Sommerfield, C.; Venherm, C.

    2003-12-01

    The continental shelves are of obvious scientific and strategic importance. However, the ability to cost-effectively collect core samples of continental shelf sediments has been limited by technical difficulties. Many sites of scientific interest are too shallow to be drilled by large drill ships, and they are too deep to be drilled economically from jack-up platforms. DOSECC has developed an Active Heave Compensated (AHC800) drilling system under sponsorship of the Office of Naval Research to overcome these obstacles by building a small active heave compensated drilling rig that can be used to collect high-quality core from selected vessels of opportunity. The AHC800 drilling rig is designed to collect continuous core to a total drill string length of 800 m. Water depths of 200 m and less are optimal; however, with some modification operation in deeper water is possible. The AHC800 senses vessel heave using a constantly tensioned low-stretch taut line attached to a seafloor weight. A linear position transducer is attached to this taut line and through the data acquisition system, the ship's distance from the bottom is communicated to the heave compensation computer running Labview RT operating system and object-based software language. This real-time control system is used to achieve a 10-ms control loop for both data gathering and output functions. The Labview RT system continuously controls two hydraulic cylinders that keep the heave carriage and the drill string at the same reference distance from the bottom. The AHC800 system was used on the R/V Knorr on the New Jersey continental shelf in water depths from 74 to 130 m from 25 Sep to 15 Oct 2002. The AHC800 system performed up to and beyond its design specifications. The rig was designed to compensate for 2.44 m of heave with an 8 s period. However, the Knorr's response was a 6 s period resulting in a significant increase in the required acceleration as well as a faster response time for the system as a whole

  8. Experimental results using active control of traveling wave power flow

    NASA Technical Reports Server (NTRS)

    Miller, David W.; Hall, Steven R.

    1991-01-01

    Active structural control experiments conducted on a 24-ft pinned-free beam derived feedback compensators on the basis of a traveling-wave approach. A compensator is thus obtained which eliminates resonant behavior by absorbing all impinging power. A causal solution is derived for this noncausal compensator which mimics its behavior in a given frequency range, using the Wiener-Hopf. This optimal Wiener-Hopf compensator's structure-damping performance is found to exceed any obtainable by means of rate feedback. Performance limitations encompassed the discovery of frequencies above which the sensor and actuator were no longer dual and an inadvertent coupling of the control hardware to unmodeled structure torsion modes.

  9. 77 FR 56710 - Proposed Information Collection (Veteran's Application for Compensation and/or Pension) Activity...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-13

    ... AFFAIRS Proposed Information Collection (Veteran's Application for Compensation and/or Pension) Activity..., for compensation and/or pension benefit sought. DATES: Written comments and recommendations on the... Compensation and/or Pension, VA Form 21-526. b. Veteran's Supplemental Claim Application, VA Form 21-526b....

  10. Anterior Cruciate Ligament Injury: Compensation during Gait using Hamstring Muscle Activity

    PubMed Central

    Catalfamo, Paola Formento; Aguiar, Gerardo; Curi, Jorge; Braidot, Ariel

    2010-01-01

    Previous research has shown that an increase in hamstring activation may compensate for anterior tibial transalation (ATT) in patients with anterior cruciate ligament deficient knee (ACLd); however, the effects of this compensation still remain unclear. The goals of this study were to quantify the activation of the hamstring muscles needed to compensate the ATT in ACLd knee during the complete gait cycle and to evaluate the effect of this compensation on quadriceps activation and joint contact forces. A two dimensional model of the knee was used, which included the tibiofemoral and patellofemoral joints, knee ligaments, the medial capsule and two muscles units. Simulations were conducted to determine the ATT in healthy and ACLd knee and the hamstring activation needed to correct the abnormal ATT to normal levels (100% compensation) and to 50% compensation. Then, the quadriceps activation and the joint contact forces were calculated. Results showed that 100% compensation would require hamstring and quadriceps activations larger than their maximum isometric force, and would generate an increment in the peak contact force at the tibiofemoral (115%) and patellofemoral (48%) joint with respect to the healthy knee. On the other hand, 50% compensation would require less force generated by the muscles (less than 0.85 of maximum isometric force) and smaller contact forces (peak tibiofemoral contact force increased 23% and peak patellofemoral contact force decreased 7.5% with respect to the healthy knee). Total compensation of ATT by means of increased hamstring activity is possible; however, partial compensation represents a less deleterious strategy. PMID:20721326

  11. Measurement and compensation of wavefront deformations and focal shifts in high-power laser optics

    NASA Astrophysics Data System (ADS)

    Mann, K.; Schäfer, B.; Stubenvoll, M.; Hentschel, K.; Zenz, M.

    2015-11-01

    We demonstrate the feasibility of passive compensation of the thermal lens effect in fused silica optics, placing suitable optical materials with negative dn/dT in the beam path of a high power near IR fiber laser. Following a brief overview of the involved mechanisms, photo-thermal absorption measurements with a Hartmann-Shack sensor are described, from which coefficients for surface/coating and bulk absorption in various materials are determined. Based on comprehensive knowledge of the 2D wavefront deformations resulting from absorption, passive compensation of thermally induced aberrations in complex optical systems is possible, as illustrated for an F-Theta objective. By means of caustic measurements during high-power operation we are able to demonstrate a 60% reduction of the focal shift in F-Theta lenses through passive compensation.

  12. Thermal lensing compensation optics for high power lasers

    NASA Astrophysics Data System (ADS)

    Scaggs, Michael; Haas, Gil

    2011-03-01

    Athermalization of focusing objectives is a common technique for optimizing imaging systems in the infrared where thermal effects are a major concern. The athermalization is generally done within the spectrum of interest and not generally applied to a single wavelength. The predominate glass used with high power infrared lasers in the near infrared of one micron, such as Nd:YAG and fiber lasers, is fused silica which has excellent thermal properties. All glasses, however, have a temperature coefficient of index of refraction (dn/dT) where as the glass heats up its index of refraction changes. Most glasses, fused silica included, have a positive dn/dT. A positive dn/dT will cause the focal length of the lens to decrease with a temperature rise. Many of the fluoride glasses, like CaF2, BaF2, LiF2, etc. have a negative dn/dT. By applying athermalization techniques of glass selection and optical design, the thermal lensing in a laser objective of a high power laser system can be substantially mitigated. We describe a passive method for minimizing thermal lensing of high power laser optics.

  13. 75 FR 29531 - Frequency Regulation Compensation in the Organized Wholesale Power Markets; Supplemental Notice...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-26

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission Frequency Regulation Compensation in the Organized Wholesale Power Markets... the April 27 Notice, the conference will provide a forum to consider issues related to...

  14. Compensating for inconsistent high power vircator microwave radar pulse sources

    NASA Astrophysics Data System (ADS)

    McAulay, Alastair D.

    2012-06-01

    We investigate a vircator as an economical high power pulsed microwave source for radar. Because of the inconsistency of spark gaps in the driver and operation of the tube based vircator, the resulting ringing pulse has a different pulse shape each time a pulse is generated. Therefore every time we pulse the source we must remove the effects of the ringing source pulse from the data resulting from that pulse. Scattering from a scene is considered random (white noise) with a superimposed non-white component due to the pulse. We propose a whitening filter to remove the effects of the ringing pulse from the random data. This produces a similar result as spectral factorization in which we first determine the pulse from the power spectrum of the data and then deconvolve the ringing pulse out of the received data. The removal of pulse specific ringing increases range resolution and allows data from sequential pulses from a single vircator or pulses from separate vircators to be combined for joint processing in a synthetic aperture radar.

  15. Examination of a PHEV Bi-Directional Charger System for V2G Reactive Power Compensation

    SciTech Connect

    Kisacikoglu, Mithat C; Ozpineci, Burak; Tolbert, Leon M

    2010-01-01

    Plug-in hybrid electric vehicles (PHEVs) potentially have the capability to fulfill the energy storage needs of the electric grid by supplying ancillary services such as reactive power compensation. However, in order to allow bidirectional power transfer, the PHEV battery charger should be designed to manage such capability. While many different battery chargers have been available since the inception of the first electric vehicles (EVs), an on-board, conductive charger with bidirectional power transferring capability have recently drawn attention due to their inherent advantages in charging accessibility, ease of use and efficiency. In this study, a reactive power compensation case study using the inverter dc-link capacitor is given when a PHEV battery is under charging operation. Finally, the impact of providing these services on the batteries is also explained.

  16. Genetic algorithms for optimal reactive power compensation planning on the national grid system

    NASA Astrophysics Data System (ADS)

    Pilgrim, J. D.

    This work investigates the use of Genetic Algorithms (GAs) for optimal Reactive power Compensation Planning (RCP) of practical power systems. In particular, RCP of the transmission system of England and Wales as owned and operated by National Grid is considered. The GA is used to simultaneously solve both the siting problem---optimisation of the installation of new devices---and the operational problem---optimisation of preventive transformer taps and the controller characteristics of dynamic compensation devices. A computer package called Genetic Compensation Placement (GCP) has been developed which uses an Integer coded GA (IGA) to solve the RCP problem. The RCP problem is implemented as a multi-objective optimisation: in the interests of security, the number of system and operational constraint violations and the deviation of the busbar voltages from the ideal are all minimised for the base (intact) case and the contingent cases. In the interests of cost reduction, the reactive power cost is minimised for the base case. The reactive power cost encompasses the costs incurred from the installation of reactive power sources and the utilisation of new and existing dynamic reactive power compensation devices. GCP is compared to SCORPION (a planning program currently being used by National Grid) which uses a combination of linear programming and heuristic back-tracking. Results are presented for a practical test system developed with the cooperation of National Grid, and it is found that GCP produces solutions that are cheaper than solutions found by SCORPION and perform extremely well: an improvement in voltage profiles, a decrease in complex power mismatches, and a reduction in MVolt Amps-reactive (VAr) utilisation were observed.

  17. A simulator investigation of engine failure compensation for powered-lift STOL aircraft

    NASA Technical Reports Server (NTRS)

    Nieuwenhuijse, A. W.; Franklin, J. A.

    1974-01-01

    A piloted simulator investigation of various engine failure compensation concepts for powered-lift STOL aircraft was carried out at the Ames Research Center. The purpose of this investigation was to determine the influence of engine failure compensation on recovery from an engine failure during the landing approach and on the precision of the STOL landing. The various concepts include: (1) cockpit warning lights to cue the pilot of an engine failure, (2) programmed thrust and roll trim compensation, (3) thrust command and (4) flight-path stabilization. The aircraft simulated was a 150 passenger four-engine, externally blown flap civil STOL transport having a 90 psf wing loading and a .56 thrust to weight ratio. Results of the simulation indicate that the combination of thrust command and flight-path stabilization offered the best engine-out landing performance in turbulence and did so over the entire range of altitudes for which engine failures occurred.

  18. onHigh-peak-power strain-compensated GaInAs/AlInAs quantum cascade lasers (λ ˜4.6 μm) based on a slightly diagonal active region design

    NASA Astrophysics Data System (ADS)

    Yang, Q.; Lösch, R.; Bronner, W.; Hugger, S.; Fuchs, F.; Aidam, R.; Wagner, J.

    2008-12-01

    Employing a "slightly diagonal" active region design for the quantum cascade lasers compared to a reference sample based on the conventional vertical transition design [R. Köhler et al., Appl. Phys. Lett. 76, 1092 (2000)], we have improved the maximum operation temperature, room-temperature maximum peak power per facet, and room-temperature slope efficiency from 320 K, 200 mW, and 570 mW/A to higher than 360 K, 3.2 W, and 2200 mW/A, respectively, for the device size of 16 μm×3 mm with as-cleaved facets operated in pulsed mode.

  19. Plastic Optical Fibre Sensor for Spine Bending Monitoring with Power Fluctuation Compensation

    PubMed Central

    Zawawi, Mohd Anwar; O'Keeffe, Sinead; Lewis, Elfed

    2013-01-01

    This paper presents the implementation of power fluctuation compensation for an intensity-based optical fibre bending sensor aimed at monitoring human spine bending in a clinical environment. To compensate for the light intensity changes from the sensor light source, a reference signal was provided via the light reflection from an aluminum foil surface fixed at a certain distance from the source fibre end tips. From the results, it was found that the investigated sensor compensation technique was capable of achieving a 2° resolution for a bending angle working range between 0° and 20°. The study also suggested that the output voltage ratio has a 0.55% diversion due to input voltage variation between 2.9 V and 3.4 V and a 0.25% output drift for a 2 h measurement. With the achieved sensor properties, human spine monitoring in a clinical environment can potentially be implemented using this approach with power fluctuation compensation. PMID:24233073

  20. 77 FR 70210 - Agency Information Collection (Veteran's Application for Compensation and/or Pension): Activity...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-23

    ... AFFAIRS Agency Information Collection (Veteran's Application for Compensation and/or Pension): Activity... Pension, VA Form 21-526. b. Veteran's Supplemental Claim Application, VA Form 21-526b. c. Authorization.... Veterans complete VA Form 21-526 to initially apply for compensation and/or pension benefits. b....

  1. Changes in Muscle Activation after Reach Training with Gravity Compensation in Chronic Stroke Patients

    ERIC Educational Resources Information Center

    Prange, Gerdienke B.; Krabben, Thijs; Renzenbrink, Gerbert J.; Ijzerman, Maarten J.; Hermens, Hermie J.; Jannink, Michiel J. A.

    2012-01-01

    The objective of this study is to examine the effect of gravity compensation training on reaching and underlying changes in muscle activation. In this clinical trial, eight chronic stroke patients with limited arm function received 18 sessions (30 min) of gravity-compensated reach training (during 6 weeks) in combination with a rehabilitation…

  2. Alleviation SSR and Low Frequency Power Oscillations in Series Compensated Transmission Line using SVC Supplementary Controllers

    NASA Astrophysics Data System (ADS)

    Kumar, Sanjiv; Kumar, Narendra

    2016-07-01

    In this work, supplementary sub-synchronous damping controllers (SSDC) are proposed for damping sub-synchronous oscillations in power systems with series compensated transmission lines. Series compensation have extensively been used as effective means of increasing the power transfer capability of a transmission lines and improving transient stability limits of power systems. Series compensation with transmission lines may cause sub-synchronous resonance (SSR). The eigenvalue investigation tool is used to ascertain the existence of SSR. It is shown that the addition of supplementary controller is able to stabilize all unstable modes for T-network model. Eigenvalue investigation and time domain transient simulation of detailed nonlinear system are considered to investigate the performance of the controllers. The efficacies of the suggested supplementary controllers are compared on the IEEE first benchmark model for computer simulations of SSR by means of time domain simulation in Matlab/Simulink environment. Supplementary SSDC are considered in order to compare effectiveness of SSDC during higher loading in alleviating the small signal stability problem.

  3. A combined compensation method for the output voltage of an insulated core transformer power supply

    NASA Astrophysics Data System (ADS)

    Yang, L.; Yang, J.; Liu, K. F.; Qin, B.; Chen, D. Z.

    2014-06-01

    An insulated core transformer (ICT) power supply is an ideal high-voltage generator for irradiation accelerators with energy lower than 3 MeV. However, there is a significant problem that the structure of the segmented cores leads to an increase in the leakage flux and voltage differences between rectifier disks. A high level of consistency in the output of the disks helps to achieve a compact structure by improving the utilization of both the rectifier components and the insulation distances, and consequently increase the output voltage of the power supply. The output voltages of the disks which are far away from the primary coils need to be improved to reduce their inhomogeneity. In this study, by investigating and comparing the existing compensation methods, a new combined compensation method is proposed, which increases the turns on the secondary coils and employs parallel capacitors to improve the consistency of the disks, while covering the entire operating range of the power supply. This method turns out to be both feasible and effective during the development of an ICT power supply. The non-uniformity of the output voltages of the disks is less than 3.5% from no-load to full-load, and the power supply reaches an output specification of 350 kV/60 mA.

  4. A combined compensation method for the output voltage of an insulated core transformer power supply.

    PubMed

    Yang, L; Yang, J; Liu, K F; Qin, B; Chen, D Z

    2014-06-01

    An insulated core transformer (ICT) power supply is an ideal high-voltage generator for irradiation accelerators with energy lower than 3 MeV. However, there is a significant problem that the structure of the segmented cores leads to an increase in the leakage flux and voltage differences between rectifier disks. A high level of consistency in the output of the disks helps to achieve a compact structure by improving the utilization of both the rectifier components and the insulation distances, and consequently increase the output voltage of the power supply. The output voltages of the disks which are far away from the primary coils need to be improved to reduce their inhomogeneity. In this study, by investigating and comparing the existing compensation methods, a new combined compensation method is proposed, which increases the turns on the secondary coils and employs parallel capacitors to improve the consistency of the disks, while covering the entire operating range of the power supply. This method turns out to be both feasible and effective during the development of an ICT power supply. The non-uniformity of the output voltages of the disks is less than 3.5% from no-load to full-load, and the power supply reaches an output specification of 350 kV/60 mA. PMID:24985809

  5. A combined compensation method for the output voltage of an insulated core transformer power supply

    SciTech Connect

    Yang, L.; Yang, J. Liu, K. F.; Qin, B.; Chen, D. Z.

    2014-06-15

    An insulated core transformer (ICT) power supply is an ideal high-voltage generator for irradiation accelerators with energy lower than 3 MeV. However, there is a significant problem that the structure of the segmented cores leads to an increase in the leakage flux and voltage differences between rectifier disks. A high level of consistency in the output of the disks helps to achieve a compact structure by improving the utilization of both the rectifier components and the insulation distances, and consequently increase the output voltage of the power supply. The output voltages of the disks which are far away from the primary coils need to be improved to reduce their inhomogeneity. In this study, by investigating and comparing the existing compensation methods, a new combined compensation method is proposed, which increases the turns on the secondary coils and employs parallel capacitors to improve the consistency of the disks, while covering the entire operating range of the power supply. This method turns out to be both feasible and effective during the development of an ICT power supply. The non-uniformity of the output voltages of the disks is less than 3.5% from no-load to full-load, and the power supply reaches an output specification of 350 kV/60 mA.

  6. Low-Power Photoplethysmogram Acquisition Integrated Circuit with Robust Light Interference Compensation

    PubMed Central

    Kim, Jongpal; Kim, Jihoon; Ko, Hyoungho

    2015-01-01

    To overcome light interference, including a large DC offset and ambient light variation, a robust photoplethysmogram (PPG) readout chip is fabricated using a 0.13-μm complementary metal–oxide–semiconductor (CMOS) process. Against the large DC offset, a saturation detection and current feedback circuit is proposed to compensate for an offset current of up to 30 μA. For robustness against optical path variation, an automatic emitted light compensation method is adopted. To prevent ambient light interference, an alternating sampling and charge redistribution technique is also proposed. In the proposed technique, no additional power is consumed, and only three differential switches and one capacitor are required. The PPG readout channel consumes 26.4 μW and has an input referred current noise of 260 pArms. PMID:26729122

  7. Low-Power Photoplethysmogram Acquisition Integrated Circuit with Robust Light Interference Compensation.

    PubMed

    Kim, Jongpal; Kim, Jihoon; Ko, Hyoungho

    2015-01-01

    To overcome light interference, including a large DC offset and ambient light variation, a robust photoplethysmogram (PPG) readout chip is fabricated using a 0.13-μm complementary metal-oxide-semiconductor (CMOS) process. Against the large DC offset, a saturation detection and current feedback circuit is proposed to compensate for an offset current of up to 30 μA. For robustness against optical path variation, an automatic emitted light compensation method is adopted. To prevent ambient light interference, an alternating sampling and charge redistribution technique is also proposed. In the proposed technique, no additional power is consumed, and only three differential switches and one capacitor are required. The PPG readout channel consumes 26.4 μW and has an input referred current noise of 260 pArms. PMID:26729122

  8. Reactive-power compensation of coal mining excavators by using a new-generation STATCOM

    SciTech Connect

    Bilgin, H.F.; Ermis, M.; Kose, K.N.; Cadirci, I.; Acik, A.; Demirci, T.; Terciyanli, A.; Kocak, C.; Yorukoglu, M.

    2007-01-15

    This paper deals with the development and implementation of a current-source-converter-based static synchronous compensator (CSC-STATCOM) applied to the volt-ampere-reactive (VAR) compensation problem of coal mining excavators. It is composed of a +/- 750-kVAR full-bridge CSC with selective harmonic elimination, a low-pass input filter tuned to 200 Hz, and a Delta/Y-connected coupling transformer for connection to medium-voltage load bus. Each power semiconductor switch is composed of an asymmetrical integrated gate commutated thyristor (IGCT) connected in series with a reverse-blocking diode and switched at 500 Hz to eliminate 5th, 7th, 11th, and 13th current harmonics produced by the CSC. Operating principles, power stage, design of dc link, and input filter are also described in this paper. It has been verified by field tests that the developed STATCOM follows rapid fluctuations in nearly symmetrical lagging and leading VAR consumption of electric excavators, resulting in nearly unity power factor on monthly basis, and the harmonic current spectra in the lines of CSC-STATCOM at the point of common coupling comply with the IEEE Standard 519-1992.

  9. Development of an improved H-bridge cascaded static synchronous compensator in power system.

    PubMed

    Zhang, Chao; Zhang, Aimin; Zhang, Hang; Bai, Yunfei; Guo, Chujia; Geng, Yingsan

    2015-06-01

    This paper presents a new configuration of H-bridge cascaded static synchronous compensator (STATCOM) based on auto disturbance rejection control and modulation wave shifting control intended for installation in industrial and utility power distribution systems. It proposes an improved controller that devotes itself not only to satisfying the requirement of dynamic reactive power compensation but also to achieving the balance of DC capacitor voltage. The new configuration is prominent in having no restriction on the number of power module. Simulation results show the proposed controller exhibits better performance in terms of response time and transient stability compared with the proportion integration controller. Two actual H-bridge cascaded STATCOMs are constructed at 10 kV, 2 MVA and 380 V, 6.5 kVA, respectively, and a series of verifications test are executed in 380 V, 6.5 kVA STATCOM experimental system. The experiment results further prove that H-bridge cascaded STATCOM with the proposed controller has excellent dynamic performance and strong robustness. PMID:26133853

  10. Development of an improved H-bridge cascaded static synchronous compensator in power system

    NASA Astrophysics Data System (ADS)

    Zhang, Chao; Zhang, Aimin; Zhang, Hang; Bai, Yunfei; Guo, Chujia; Geng, Yingsan

    2015-06-01

    This paper presents a new configuration of H-bridge cascaded static synchronous compensator (STATCOM) based on auto disturbance rejection control and modulation wave shifting control intended for installation in industrial and utility power distribution systems. It proposes an improved controller that devotes itself not only to satisfying the requirement of dynamic reactive power compensation but also to achieving the balance of DC capacitor voltage. The new configuration is prominent in having no restriction on the number of power module. Simulation results show the proposed controller exhibits better performance in terms of response time and transient stability compared with the proportion integration controller. Two actual H-bridge cascaded STATCOMs are constructed at 10 kV, 2 MVA and 380 V, 6.5 kVA, respectively, and a series of verifications test are executed in 380 V, 6.5 kVA STATCOM experimental system. The experiment results further prove that H-bridge cascaded STATCOM with the proposed controller has excellent dynamic performance and strong robustness.

  11. Antenna gain of actively compensated free-space optical communication systems under strong turbulence conditions.

    PubMed

    Juarez, Juan C; Brown, David M; Young, David W

    2014-05-19

    Current Strehl ratio models for actively compensated free-space optical communications terminals do not accurately predict system performance under strong turbulence conditions as they are based on weak turbulence theory. For evaluation of compensated systems, we present an approach for simulating the Strehl ratio with both low-order (tip/tilt) and higher-order (adaptive optics) correction. Our simulation results are then compared to the published models and their range of turbulence validity is assessed. Finally, we propose a new Strehl ratio model and antenna gain equation that are valid for general turbulence conditions independent of the degree of compensation. PMID:24921373

  12. Enhanced High Performance Power Compensation Methodology by IPFC Using PIGBT-IDVR

    PubMed Central

    Arumugom, Subramanian; Rajaram, Marimuthu

    2015-01-01

    Currently, power systems are involuntarily controlled without high speed control and are frequently initiated, therefore resulting in a slow process when compared with static electronic devices. Among various power interruptions in power supply systems, voltage dips play a central role in causing disruption. The dynamic voltage restorer (DVR) is a process based on voltage control that compensates for line transients in the distributed system. To overcome these issues and to achieve a higher speed, a new methodology called the Parallel IGBT-Based Interline Dynamic Voltage Restorer (PIGBT-IDVR) method has been proposed, which mainly spotlights the dynamic processing of energy reloads in common dc-linked energy storage with less adaptive transition. The interline power flow controller (IPFC) scheme has been employed to manage the power transmission between the lines and the restorer method for controlling the reactive power in the individual lines. By employing the proposed methodology, the failure of a distributed system has been avoided and provides better performance than the existing methodologies. PMID:26613101

  13. Enhanced High Performance Power Compensation Methodology by IPFC Using PIGBT-IDVR.

    PubMed

    Arumugom, Subramanian; Rajaram, Marimuthu

    2015-01-01

    Currently, power systems are involuntarily controlled without high speed control and are frequently initiated, therefore resulting in a slow process when compared with static electronic devices. Among various power interruptions in power supply systems, voltage dips play a central role in causing disruption. The dynamic voltage restorer (DVR) is a process based on voltage control that compensates for line transients in the distributed system. To overcome these issues and to achieve a higher speed, a new methodology called the Parallel IGBT-Based Interline Dynamic Voltage Restorer (PIGBT-IDVR) method has been proposed, which mainly spotlights the dynamic processing of energy reloads in common dc-linked energy storage with less adaptive transition. The interline power flow controller (IPFC) scheme has been employed to manage the power transmission between the lines and the restorer method for controlling the reactive power in the individual lines. By employing the proposed methodology, the failure of a distributed system has been avoided and provides better performance than the existing methodologies. PMID:26613101

  14. Multistability in the mixtures of smectic-C^{*} materials with compensated twisting power.

    PubMed

    Emelyanenko, A V; Pozhidaev, E P

    2016-04-01

    The effect of multistability in the mixtures of smectic-C^{*} materials with compensated twisting power, i.e., the existence of a large number of almost equiprobable states in the same mixture under the same conditions, is analyzed in the framework of elastic continuum theory. A simple molecular model is also considered. It is shown that multistability can follow from the bulk properties of the smectic-C^{*} materials with compensated twisting power, but with high spontaneous polarization. Multistability leads to the formation of ferroelectric domains, in which the director oscillates in space. The length and amplitude of this oscillation is tunable smoothly by an electric field. Theoretical results for the domain length agree completely with the experimental data. A suggestion is made as to why each domain structure is remembered without the energy consumption, when the electric field is abruptly switched off. The structural dependence on material parameters, such as the spontaneous polarization, the elastic constant, and the equilibrium wave number, is predicted. PMID:27176364

  15. Multistability in the mixtures of smectic-C* materials with compensated twisting power

    NASA Astrophysics Data System (ADS)

    Emelyanenko, A. V.; Pozhidaev, E. P.

    2016-04-01

    The effect of multistability in the mixtures of smectic-C* materials with compensated twisting power, i.e., the existence of a large number of almost equiprobable states in the same mixture under the same conditions, is analyzed in the framework of elastic continuum theory. A simple molecular model is also considered. It is shown that multistability can follow from the bulk properties of the smectic-C* materials with compensated twisting power, but with high spontaneous polarization. Multistability leads to the formation of ferroelectric domains, in which the director oscillates in space. The length and amplitude of this oscillation is tunable smoothly by an electric field. Theoretical results for the domain length agree completely with the experimental data. A suggestion is made as to why each domain structure is remembered without the energy consumption, when the electric field is abruptly switched off. The structural dependence on material parameters, such as the spontaneous polarization, the elastic constant, and the equilibrium wave number, is predicted.

  16. A compensation-based power flow method for weakly meshed distribution and transmission networks

    SciTech Connect

    Shirmohammadi, D.; Hong, H.W.; Semlyen, A.; Luo, G.X.

    1988-05-01

    This paper describes a new power flow method for solving weakly meshed distribution and transmission networks, using a multi-port compensation technique and basic formulation of Kirchhoff's laws. This method has excellent convergence characteristics and is very robust. A computer program implementing this power flow solution scheme was developed and successfully applied to several practical distribution networks with radial and weakly meshed structure. This program was also successfully used for solving radial and weakly meshed transmission networks. The method can be applied to the solution of both the three-phase (unbalanced) and single-phase (balanced) representation of the network. In this paper, however, only the single phase representation is treated in detail.

  17. Power-compensated displacement sensing based on single mode-multimode fiber Bragg grating structure

    NASA Astrophysics Data System (ADS)

    Sun, An; Wu, Zhishen; Huang, Huang

    2013-01-01

    In this paper, power-compensated displacement sensing is proposed and investigated experimentally based on single mode-multimode fiber Bragg grating (FBG) structure, which is fabricated by a single mode fiber and an FBG written on 105/125 μm graded-index multimode fiber (MMF). Experimental results verify that the reflected peak power of multiple wavelengths in single mode-multimode fiber Bragg grating structure shows different response to displacement induced bending of transmitting multimode fiber as the result of multimode interference (MMI). By employing different bending responses between multiple wavelengths of multimode FBG, ratiometric detection based high sensitive displacement measurement can be achieved, which provides a simple and practical method for displacement sensing and meanwhile a potential solution for multi-parameter measurement.

  18. A novel method for combating dispersion induced power fading in dispersion compensating fiber.

    PubMed

    Lebedev, Alexander; Olmos, J J Vegas; Iglesias, Miguel; Forchhammer, Søren; Monroy, Idelfonso Tafur

    2013-06-01

    We experimentally investigate the performance of 60 GHz double sideband (DSB) radio over fiber (RoF) links that employ dispersion compensating fiber (DCF). Error free transmission of 3 Gbps signals over 1 m of wireless distance is reported. In order to overcome experimentally observed chromatic dispersion (CD) induced power fading of radio frequency (RF) signal, we propose a method for improvement of RF carrier-to-noise (C/N) ratio through introduction of a degree of RF frequency tunability. Overall results improve important aspects of directly modulated RoF systems and demonstrate the feasibility of high carrier frequency and wide bandwidth RF signals delivery in RoF links including DCF fiber. Error free performance that we obtain for 3 Gbps amplitude shift-keying (ASK) signals enables uncompressed high-definition 1080p video delivery. PMID:23736614

  19. Radical advancement in multi-spectral imaging for autonomous vehicles (UAVs, UGVs, and UUVs) using active compensation.

    SciTech Connect

    Clark, Brian F.; Bagwell, Brett E.; Wick, David Victor

    2007-01-01

    The purpose of this LDRD was to demonstrate a compact, multi-spectral, refractive imaging systems using active optical compensation. Compared to a comparable, conventional lens system, our system has an increased operational bandwidth, provides for spectral selectivity and, non-mechanically corrects aberrations induced by the wavelength dependent properties of a passive refractive optical element (i.e. lens). The compact nature and low power requirements of the system lends itself to small platforms such as autonomous vehicles. In addition, the broad spectral bandwidth of our system would allow optimized performance for both day/night use, and the multi-spectral capability allows for spectral discrimination and signature identification.

  20. Physical activity compensates for increased mortality risk among older people with poor muscle strength.

    PubMed

    Portegijs, E; Rantanen, T; Sipilä, S; Laukkanen, P; Heikkinen, E

    2007-10-01

    The aim of the study was to determine whether habitual physical activity can compensate for the increased mortality risk among older people with poor muscle strength. Mortality was followed up for 10 years after laboratory examination in 558 community dwelling 75- and 80-year-old men and women. Maximal isometric strength of five muscle groups was measured and tertile cut-off points were used to categorize participants. Participants, who reported moderate physical activity for at least 4 h a week, were categorized as physically active and the others as sedentary. High muscle strength and physical activity both protected from mortality, but their effect was not additive. Within each muscle strength tertile, physically active people had a lower mortality risk than sedentary people, the effect being most pronounced among those with lower strength in all muscle groups. A high level of physical activity may thus compensate for the increased mortality associated with low muscle strength. PMID:17166169

  1. Active and passive compensation of APPLE II-introduced multipole errors through beam-based measurement

    NASA Astrophysics Data System (ADS)

    Chung, Ting-Yi; Huang, Szu-Jung; Fu, Huang-Wen; Chang, Ho-Ping; Chang, Cheng-Hsiang; Hwang, Ching-Shiang

    2016-08-01

    The effect of an APPLE II-type elliptically polarized undulator (EPU) on the beam dynamics were investigated using active and passive methods. To reduce the tune shift and improve the injection efficiency, dynamic multipole errors were compensated using L-shaped iron shims, which resulted in stable top-up operation for a minimum gap. The skew quadrupole error was compensated using a multipole corrector, which was located downstream of the EPU for minimizing betatron coupling, and it ensured the enhancement of the synchrotron radiation brightness. The investigation methods, a numerical simulation algorithm, a multipole error correction method, and the beam-based measurement results are discussed.

  2. Estimation of Transmitting Power to Compensate for Rain Attenuation for a Broadcasting Satellite System in the 21-GHz Band

    NASA Astrophysics Data System (ADS)

    Minematsu, Fumiaki; Tanaka, Shoji; Nakagawa, Hitoshi; Kawaguchi, Yutaka

    2002-01-01

    1. INTRODUCTION Rain attenuation in the 21-GHz band is much larger than that in the conventionally used 12-GHz band and the rain attenuation causes more serious program interruptions compared with that in the 12-GHz band. We are now studying an advanced broadcasting satellite in the 21-GHz band that enables adaptive compensation for heavy rain area by boosted beams using an on-board phased-array-transmitting antenna. To know the scale of this satellite system, it is important to estimate transmitting power needed to compensate for rain attenuation. Rain attenuation has so close association with rainfall that it is possible to estimate rain attenuation by measured rainfall. Japan meteorological agency is measuring 1-hour rainfalls for about 1300 locations in Japan. In this study, 1-hour rainfall data accumulated at more than 1000 locations over a period of 20 years were used statistically to grasp rainfall distribution throughout Japan and the transmitting power for compensation was estimated by use of these data. 2. CALCULATION MODEL FOR TRANSMITTING POWER ESTIMATION Assumed rain attenuation compensation area for Japanese archipelago was divided into 112 square areas. A size of each square was 0.1 degree in terms of azimuth and elevation angle for the beam direction of satellite transmitting antenna. For calculation, the link margin of 3.5 dB for clear sky was given to the area where 1-hour rainfall not larger than 3 mm was detected. For other square areas where 1-hour rainfall larger than 3 mm was detected, the link margin of 12 dB was given. The former link margin corresponds to the service availability of 99 % and the latter does to that of 99.9 % in an average year in Tokyo. A total system efficiency included radiation efficiency of the transmitting antenna of 1.0 was assumed. As modulation scheme, trellis coded 8-PSK (TC8PSK) was assumed. The required reception CN ratio for TC8PSK is 10.7 dB. As to TC8PSK, the baud rate of 57.72 Mbaud gives more than 100 Mbps

  3. The voltage profile improvement using static var compensator (SVC) in power system transmission

    NASA Astrophysics Data System (ADS)

    Ramdan, G. M.; Mulyadi, Y.; Hasbullah

    2016-04-01

    In transmission system named ‘Subsistem Bandung Selatan dan New Ujungberung’ there are the voltage drop which relatively high and the voltage profile at the receiving ends below 0.95 p.u. Therefore, this research proposed a method to improve the voltage profile in the transmission system using one of Flexible Alternating Current Transmission System (FACTS) technology which is Static Var Compensator (SVC) and ‘Subsistem Bandung Selatan and New Ujungberung’ as the object. This research aims to get the voltage profile in ‘Subsistem Bandung Selatan dan New Ujungberung’ before and after connected to SVC and to set optimal location and rating of SVC to maintain the voltage profile at the system that has desire range (0.95 p.u – 1.05 p.u). To get the result in accordance with these objects, Newton –Raphson power flow solution is applied to the system. The result of Newton- Raphson power flow solution of the system shows the voltage profile before connecting to SVC are averagely 140.95 kV or 0.94 p.u while after connecting to SVC are 145.28 kV or 0.97 p.u. The SVC installation is connected to ‘Bandung Utara I’ as the weakest bus, and the SVC rating is -250 Mvar to 300 Mvar.

  4. Power amplifier linearization technique with IQ imbalance and crosstalk compensation for broadband MIMO-OFDM transmitters

    NASA Astrophysics Data System (ADS)

    Gregorio, Fernando; Cousseau, Juan; Werner, Stefan; Riihonen, Taneli; Wichman, Risto

    2011-12-01

    The design of predistortion techniques for broadband multiple input multiple output-OFDM (MIMO-OFDM) systems raises several implementation challenges. First, the large bandwidth of the OFDM signal requires the introduction of memory effects in the PD model. In addition, it is usual to consider an imbalanced in-phase and quadrature (IQ) modulator to translate the predistorted baseband signal to RF. Furthermore, the coupling effects, which occur when the MIMO paths are implemented in the same reduced size chipset, cannot be avoided in MIMO transceivers structures. This study proposes a MIMO-PD system that linearizes the power amplifier response and compensates nonlinear crosstalk and IQ imbalance effects for each branch of the multiantenna system. Efficient recursive algorithms are presented to estimate the complete MIMO-PD coefficients. The algorithms avoid the high computational complexity in previous solutions based on least squares estimation. The performance of the proposed MIMO-PD structure is validated by simulations using a two-transmitter antenna MIMO system. Error vector magnitude and adjacent channel power ratio are evaluated showing significant improvement compared with conventional MIMO-PD systems.

  5. Active phase compensation system for fiber optic holography

    NASA Technical Reports Server (NTRS)

    Mercer, Carolyn R.; Beheim, Glenn

    1989-01-01

    Fiber optic delivery systems promise to extend the application of holography to severe environments by simplifying test configurations and permitting the laser to be remotely placed in a more benign location. However, the introduction of optical fiber leads to phase stability problems. Environmental effects cause the pathlengths of the fibers to change randomly, preventing the formation of stationary interference patterns which are required for holography. An active phase control system has been designed and used with an all-fiber optical system to stabilize the phase difference between light emitted from two fibers, and to step the phase difference by 90 deg without applying any constraints on the placement of the fibers. The accuracy of the phase steps is shown to be better than 0.02 deg., and a stable phase difference can be maintained for 30 min. This system can be applied to both conventional and electro-optic holography, as well as to any system where the maintenance of an accurate phase difference between two coherent beams is required.

  6. Active phase compensation system for fiber optic holography

    NASA Technical Reports Server (NTRS)

    Mercer, Carolyn R.; Beheim, Glenn

    1988-01-01

    Fiber optic delivery systems promise to extend the application of holography to severe environments by simplifying test configurations and permitting the laser to be remotely placed in a more benign location. However, the introduction of optical fiber leads to phase stability problems. Environmental effects cause the pathlengths of the fibers to change randomly, preventing the formation of stationary interference patterns which are required for holography. An active phase control system has been designed and used with an all-fiber optical system to stabilize the phase difference between light emitted from two fibers, and to step the phase difference by 90 deg without applying any constraints on the placement of the fibers. The accuracy of the phase steps is shown to be better than 0.02 deg., and a stable phase difference can be maintained for 30 min. This system can be applied to both conventional and electro-optic holography, as well as to any system where the maintenance of an accurate phase difference between two coherent beams is required.

  7. Increased activity in frontal motor cortex compensates impaired speech perception in older adults

    PubMed Central

    Du, Yi; Buchsbaum, Bradley R.; Grady, Cheryl L.; Alain, Claude

    2016-01-01

    Understanding speech in noisy environments is challenging, especially for seniors. Although evidence suggests that older adults increasingly recruit prefrontal cortices to offset reduced periphery and central auditory processing, the brain mechanisms underlying such compensation remain elusive. Here we show that relative to young adults, older adults show higher activation of frontal speech motor areas as measured by functional MRI during a syllable identification task at varying signal-to-noise ratios. This increased activity correlates with improved speech discrimination performance in older adults. Multivoxel pattern classification reveals that despite an overall phoneme dedifferentiation, older adults show greater specificity of phoneme representations in frontal articulatory regions than auditory regions. Moreover, older adults with stronger frontal activity have higher phoneme specificity in frontal and auditory regions. Thus, preserved phoneme specificity and upregulation of activity in speech motor regions provide a means of compensation in older adults for decoding impoverished speech representations in adverse listening conditions. PMID:27483187

  8. Active compensation of large dispersion of femtosecond pulses for precision laser ranging.

    PubMed

    Lee, Sang-Hyun; Lee, Joohyung; Kim, Young-Jin; Lee, Keunwoo; Kim, Seung-Woo

    2011-02-28

    We describe an active way of compensation for large dispersion induced in the femtosecond light pulses travelling in air for laser ranging. The pulse duration is consistently regulated at 250 fs by dispersion control, allowing sub-micrometer resolution in measuring long distances by means of time-of-flight measurement. This method could facilitate more reliable applications of femtosecond pulses for satellite laser ranging, laser altimetry and active LIDAR applications. PMID:21369227

  9. Dosage Compensation in DROSOPHILA MELANOGASTER Triploids. II. Glucose-6-Phosphate Dehydrogenase Activity

    PubMed Central

    Maroni, Gustavo; Plaut, Walter

    1973-01-01

    The level of activity of the enzyme glucose-6-phosphate dehydrogenase was determinel in flies having seven different chromosomic constitutions. All those having an integral number of chromosomes [XAA, XXAA, XAAA, XXAAA, and XXXAAA (X=X chromosome, A=set of autosomes)] were found to have similar units of enzyme activity/mg live weight, while diploid females with a duplication and triploid females with a deficiency showed dosage effect. The amount of enzyme activity per cell, on the other hand, is also independent of the number of X's present but appears roughly proportional to the number of sets of autosomes.—It is proposed that dosage-compensated sex-linked genes are controlled by a positively acting regulatory factor(s) of autosomal origin. With this hypothesis it is possible to explain dosage compensation as a consequence of general regulatory mechanisms without invoking a special device which applies only to the X chromosomes. PMID:17248620

  10. Study of static reactive power compensators for high-voltage power systems. Final report, May 12, 1981

    SciTech Connect

    Byerly, R.T.; Bennon, R.J.; Taylor, E.R. Jr.; Poznaniak, D.T.

    1981-05-12

    A general study of the application of static VAR compensators (SVC's) to high-voltage transmission systems has been performed. Considerable emphasis has been placed on improvements to synchronous stability, and it is shown that SVC's can provide significant benefits in terms of damping for unstable modes of oscillation and increases in transient stability limits. This report includes descriptions of static VAR compensators, technical and economic comparisons of different compensators, compensator models for system studies, comprehensive study procedures, study results for two small-scale systems, and guidelines for SVC application.

  11. An investigation on motor-driven power steering-based crosswind disturbance compensation for the reduction of driver steering effort

    NASA Astrophysics Data System (ADS)

    Kim, Kyuwon; Kim, Boemjun; Go, Youngil; Park, Jaeyong; Park, Joonhong; Suh, Insoo; Yi, Kyongsu

    2014-07-01

    This paper describes a lateral disturbance compensation algorithm for an application to a motor-driven power steering (MDPS)-based driver assistant system. The lateral disturbance including wind force and lateral load transfer by bank angle reduces the driver's steering refinement and at the same time increases the possibility of an accident. A lateral disturbance compensation algorithm is designed to determine the motor overlay torque of an MDPS system for reducing the manoeuvreing effort of a human driver under lateral disturbance. Motor overlay torque for the compensation of driver's steering torque induced by the lateral disturbance consists of human torque feedback and feedforward torque. Vehicle-driver system dynamics have been investigated using a combined dynamic model which consists of a vehicle dynamic model, driver steering dynamic model and lateral disturbance model. The human torque feedback input has been designed via the investigation of the vehicle-driver system dynamics. Feedforward input torque is calculated to compensate additional tyre self-aligning torque from an estimated lateral disturbance. The proposed compensation algorithm has been implemented on a developed driver model which represents the driver's manoeuvreing characteristics under the lateral disturbance. The developed driver model has been validated with test data via a driving simulator in a crosswind condition. Human-in-the-loop simulations with a full-scale driving simulator on a virtual test track have been conducted to investigate the real-time performance of the proposed lateral disturbance compensation algorithm. It has been shown from simulation studies and human-in-the-loop simulation results that the driver's manoeuvreing effort and a lateral deviation of the vehicle under the lateral disturbance can be significantly reduced via the lateral disturbance compensation algorithm.

  12. Subjective Career Success and Emotional Well-Being: Longitudinal Predictive Power of Selection, Optimization, and Compensation.

    ERIC Educational Resources Information Center

    Wiese, Bettina S.; Freund, Alexandra M.; Baltes, Paul B.

    2002-01-01

    A 3-year study of 82 young professionals found that work-related well-being was predicted by selection (commitment to personal goals), optimization (application of goal-related skills), and compensation (maintaining goals in the face of loss). The degree of compensation predicted emotional well-being and job satisfaction 3 years later. (Contains…

  13. Adaptive settings of distance relay for MOV-protected series compensated line with distributed capacitance considering wind power

    NASA Astrophysics Data System (ADS)

    Sivov, Oleg Viktorovich

    Series compensated lines are protected from overvoltage by metal-oxide-varistors (MOVs) connected in parallel with the capacitor bank. The nonlinear characteristics of MOV devices add complexity to fault analysis and distance protection operation. During faults, the impedance of the line is modified by an equivalent impedance of the parallel MOV/capacitor circuit, which affects the distance protection. The intermittent wind generation introduces additional complexity to the system performance and distance protection. Wind variation affects the fault current level and equivalent MOV/capacitor impedance during a fault, and hence the distance relay operation. This thesis studies the impact of the intermittent wind power generation on the operation of MOV during faults. For the purpose of simulation, an equivalent wind farm model is proposed to generate a wind generation profile using wind farm generation from California independent system operator (ISO) as a guide for wind power variation to perform the study. The IEEE 12-bus test system is modified to include MOV-protected series capacitor and the equivalent wind farm model. The modified test system is simulated in the MATLAB/Simulink environment. The study has been achieved considering three phase and single line to ground (SLG) faults on the series compensated line to show the effect of wind variation on the MOV operation. This thesis proposes an adaptive setting method for the mho relay distance protection of series compensated line considering effects of wind power variation and MOV operation. The distributed parameters of a transmission line are taken into account to avoid overreaching and underreaching of distance relays. The study shows that variable wind power affects system power flow and fault current in the compensated line during a fault which affects the operation of MOVs for different fault conditions. The equivalent per-phase impedance of the MOV/capacitor circuit has an effect on the system operation

  14. ATPase activity and its temperature compensation of the cyanobacterial clock protein KaiC.

    PubMed

    Murakami, Reiko; Miyake, Ayumi; Iwase, Ryo; Hayashi, Fumio; Uzumaki, Tatsuya; Ishiura, Masahiro

    2008-04-01

    KaiA, KaiB and KaiC constitute the circadian clock machinery in cyanobacteria. KaiC is a homohexamer; its subunit contains duplicated halves, each with a set of ATPase motifs. Here, using highly purified KaiC preparations of the thermophilic cyanobacterium Thermosynechococcus elongatus BP-1 produced in Escherichia coli, we found that the N- and C-terminal domains of KaiC had extremely weak ATPase activity. ATPase activity showed temperature compensation in wild-type KaiC, but not in KaiC(S431A/T432A), a mutant that lacks two phosphorylation sites. We concluded that KaiC phosphorylation is involved in the ATPase temperature-compensation mechanism-which is probably critical to the stability of the circadian clock in cyanobacteria-and we hypothesized the following temperature-compensation mechanism: (i) The C-terminal phosphorylation sites of a KaiC hexamer subunit are phosphorylated by the C-terminal domain of an adjacent KaiC subunit; (ii) the phosphorylation suppresses the ATPase activity of the C-terminal domain; and (iii) the phosphorylated KaiC spontaneously dephosphorylates, resulting in the recover of ATPase activity. PMID:18363969

  15. Robustness analysis and controller design for static var compensators in power systems

    NASA Astrophysics Data System (ADS)

    Yu, Xuechun I.

    In the North American electric power interconnection, control systems play a prominent role in the stabilization and reliable operation of the system. With the advent of competition and deregulation, systems are being operated closer than ever to the limits. This setting necessitates a systematic procedure to analyze and design controls in power systems which demonstrate good performance for a range of operating conditions. The current industry practice for the analysis and design of controls consists of conventional linear analysis tools coupled with detailed nonlinear simulation of the designed controls. This approach is time consuming and does not guarantee robustness. In this dissertation, we analyze the robustness of the static var compensator's (SVC's) control setting and design a supplementary damping controller for the SVC based on the structured singular value (SSV or mu), which allows computation of an effective measure for robustness in the presence of real parametric uncertainties. The robustness problem in the SSV framework is set up for the multimachine power system. In this formulation the effect of the parameter variations is captured in terms of the varying elements of the linearized system matrix. The uncertainty bounds on the varying elements are determined by running a series of power flow calculations and performing a polynomial fit. The system robustness in terms of the SSV or mu is examined using both the frequency sweep test and the state space mu test. The results on test systems show that the analysis procedure accurately predicts the range of stable operating conditions which are verified by repeated eigenvalue analysis. Some of the issues that arise in the design of a suitable supplementary controller for the SVC include the choice of the location and voltage level of the SVC, and the choice of the control signals for the supplementary controller. These issues are carefully investigated and incorporated into the design procedure. The

  16. Active sensor/actuator assemblies for vibration damping, compensation, measurement, and testing

    NASA Astrophysics Data System (ADS)

    Ryaboy, Vyacheslav M.; Kasturi, Prakash S.

    2010-04-01

    The vibration control module known as IQ damper had been developed as part of active vibration damping system for optical tables and other precision vibration isolated platforms. The present work describes steps to expand the application of these units to other tasks, namely, (1) dynamic testing of structures and (2) compensation of forced vibration in local areas. The sensor-actuator assembly, including signal conditioning circuits, is designed as a compact dynamically symmetric module with mechanical interface to an optical table. The test data show that the vibration control modules can be used to measure dynamic compliance characteristics of optical tables with precision comparable to that of dedicated vibration measurement systems. Stable concerted work of active vibration control modules compensating forced harmonic vibration is demonstrated experimentally.

  17. Single-Phase Active Boost Rectifier with Power Factor Correction for Wireless Power Transfer Applications

    SciTech Connect

    Chinthavali, Madhu Sudhan; Onar, Omer C; Miller, John M; Tang, Lixin

    2013-01-01

    Wireless Power Transfer (WPT) technology is a novel research area in the charging technology that bridges utility and the automotive industries. There are various solutions that are currently being evaluated by several research teams to find the most efficient way to manage the power flow from the grid to the vehicle energy storage system. There are different control parameters that can be utilized to compensate for the change in the impedance. To understand the power flow through the system this paper presents a novel approach to the system model and the impact of different control parameters on the load power. The implementation of an active front-end rectifier on the grid side for power factor control and voltage boost capability for load power regulation is also discussed.

  18. An attack aimed at active phase compensation in one-way phase-encoded QKD systems

    NASA Astrophysics Data System (ADS)

    Dong, Zhao-Yue; Yu, Ning-Na; Wei, Zheng-Jun; Wang, Jin-Dong; Zhang, Zhi-Ming

    2014-08-01

    Phase drift is an inherent problem in one-way phase-encoded quantum key distribution (QKD) systems. Although combining passive with active phase compensation (APC) processes can effectively compensate for the phase drift, the security problems brought about by these processes are rarely considered. In this paper, we point out a security hole in the APC process and put forward a corresponding attack scheme. Under our proposed attack, the quantum bit error rate (QBER) of the QKD can be close to zero for some conditions. However, under the same conditions the ratio r of the key "0" and the key "1" which Bob (the legal communicators Alice and Bob) gets is no longer 1:1 but 2:1, which may expose Eve (the eavesdropper). In order to solve this problem, we modify the resend strategy of the attack scheme, which can force r to reach 1 and the QBER to be lower than the tolerable QBER.

  19. Design of a H{sub {infinity}}-optimal servo compensator for the frequency and voltage control of power plants

    SciTech Connect

    Kiffmeier, U.; Unbehauen, H.

    1994-12-31

    This contribution investigates modern H{sub {infinity}} control concepts for frequency and voltage control of power plants. Based on a linearized model for a national grid H{sub {infinity}}-optimal servo compensators have been designed using a frequency domain approach recently published by the authors. As demonstrated in this paper, the multivariable H{sub {infinity}}-controller shows superior performance with respect to setting time and damping of oscillations compared to classical controllers of P/PID type.

  20. Study on a Mechanical Semi-Active Heave Compensation System of Drill String for Use on Floating Drilling Platform.

    PubMed

    Liu, Qingyou; Tang, Yang; Huang, Chongjun; Xie, Chong

    2015-01-01

    There are some disadvantages for existing heave compensation systems of drill string used for the Floating Drilling Platform (FDP), including high energy consumption, large and complex structure, and expensive manufacturing and maintenance costs. In view of the above, we present a streamlined mechanical semi-active heave compensation system (MSAHC) in this study. This system consists of active compensation part with the pinion and rack and passive compensation part. In order to evaluate system performance of the MSAHC, we establish its simulation model with AMEsim software. In the process of simulation, displacement of rotary hook and energy consumption is regarded as performance parameters of the system. And the change rule of two performance parameters are analyzed by changing these design parameters including gear radius of the pinion and rack, scale coefficient of PID, rotary hook load, heave height and heave period of the FDP, and accumulator volume. Then, based on the simulation results of the MSAHC system performance, we have selected out a best set of design parameters from them. Moreover, the feasibility of the design scheme of the MSAHC is effectively verified by comparison with the existing three heave compensation system. The result shows that the energy consumption of the MSAHC is lower than the active heave compensation system (AHC) and the semi-active heave compensation system (SAHC) when achieving a same compensation effect as well as the accumulator volume of MSAHC is half of the passive heave compensation system (PHC). Therefore, the new designed MSAHC not only ensure compensation effect but also lower energy consumption, and its structure is simplified by adopting the simple mechanical structure to decrease manufacturing cost, maintenance cost and floor space. PMID:26186620

  1. Study on a Mechanical Semi-Active Heave Compensation System of Drill String for Use on Floating Drilling Platform

    PubMed Central

    Liu, Qingyou; Tang, Yang; Huang, Chongjun; Xie, Chong

    2015-01-01

    There are some disadvantages for existing heave compensation systems of drill string used for the Floating Drilling Platform (FDP), including high energy consumption, large and complex structure, and expensive manufacturing and maintenance costs. In view of the above, we present a streamlined mechanical semi-active heave compensation system (MSAHC) in this study. This system consists of active compensation part with the pinion and rack and passive compensation part. In order to evaluate system performance of the MSAHC, we establish its simulation model with AMEsim software. In the process of simulation, displacement of rotary hook and energy consumption is regarded as performance parameters of the system. And the change rule of two performance parameters are analyzed by changing these design parameters including gear radius of the pinion and rack, scale coefficient of PID, rotary hook load, heave height and heave period of the FDP, and accumulator volume. Then, based on the simulation results of the MSAHC system performance, we have selected out a best set of design parameters from them. Moreover, the feasibility of the design scheme of the MSAHC is effectively verified by comparison with the existing three heave compensation system. The result shows that the energy consumption of the MSAHC is lower than the active heave compensation system (AHC) and the semi-active heave compensation system (SAHC) when achieving a same compensation effect as well as the accumulator volume of MSAHC is half of the passive heave compensation system (PHC). Therefore, the new designed MSAHC not only ensure compensation effect but also lower energy consumption, and its structure is simplified by adopting the simple mechanical structure to decrease manufacturing cost, maintenance cost and floor space. PMID:26186620

  2. Active Power Control from Wind Power (Presentation)

    SciTech Connect

    Ela, E.; Brooks, D.

    2011-04-01

    In order to keep the electricity grid stable and the lights on, the power system relies on certain responses from its generating fleet. This presentation evaluates the potential for wind turbines and wind power plants to provide these services and assist the grid during critical times.

  3. Analysis and active compensation of microphonics in continuous wave narrow-bandwidth superconducting cavities

    NASA Astrophysics Data System (ADS)

    Neumann, A.; Anders, W.; Kugeler, O.; Knobloch, J.

    2010-08-01

    Many proposals for next generation light sources based on single pass free electron lasers or energy recovery linac facilities require a continuous wave (cw) driven superconducting linac. The effective beam loading in such machines is very small and in principle the cavities can be operated at a bandwidth of a few Hz and with less than a few kW of rf power. However, a power reserve is required to ensure field stability. A major error source is the mechanical microphonics detuning of the niobium cavities. To understand the influence of cavity detuning on longitudinal beam stability, a measurement program has been started at the horizontal cavity test facility HoBiCaT at HZB to study TESLA-type cavities. The microphonics detuning spectral content, peak detuning values, and the driving terms for these mechanical oscillations have been analyzed. In combination with the characterization of cw-adapted fast tuning systems based on the piezoelectric effect this information has been used to design a detuning compensation algorithm. It has been shown that a compensation factor between 2-7 is achievable, reducing the typical detuning of 2-3 Hz rms to below 0.5 Hz rms. These results were included in rf-control simulations of the cavities, and it was demonstrated that a phase stability below 0.02° can be achieved.

  4. Compensation for Adolescents’ School Mental Load by Physical Activity on Weekend Days

    PubMed Central

    Kudláček, Michal; Frömel, Karel; Jakubec, Lukáš; Groffik, Dorota

    2016-01-01

    Introduction and objective: Increasing mental load and inadequate stress management significantly affect the efficiency, success and safety of the educational/working process in adolescents. The objective of this study is to determine the extent that adolescents compensate for their school mental load by physical activity (PA) on weekend days and, thus, to contribute to the objective measurement of mental load in natural working conditions. Methods: A cross-sectional study was conducted between September 2013 and April 2014. A set of different methods was employed—self-administered questionnaire (IPAQ-long questionnaire), objective measurements—pedometers, and accelerometers (ActiTrainers). They was distributed to 548 students from 17 high schools. Participants’ mental load was assessed based on the difference between PA intensity and/or physical inactivity and heart rate range. Results: The participants with the highest mental load during school lessons do not compensate for this load by PA on weekend days. Conclusions: Adolescents need to be encouraged to be aware of their subjective mental load and to intentionally compensate for this load by PA on weekend days. It is necessary to support the process of adopting habits by sufficient physical literacy of students, as well as teachers, and by changes in the school program. PMID:27005652

  5. Characterization and modelling of the boron-oxygen defect activation in compensated n-type silicon

    SciTech Connect

    Schön, J.; Niewelt, T.; Broisch, J.; Warta, W.; Schubert, M. C.

    2015-12-28

    A study of the activation of the light-induced degradation in compensated n-type Czochralski grown silicon is presented. A kinetic model is established that verifies the existence of both the fast and the slow components known from p-type and proves the quadratic dependence of the defect generation rates of both defects on the hole concentration. The model allows for the description of lifetime degradation kinetics in compensated n-type silicon under various intensities and is in accordance with the findings for p-type silicon. We found that the final concentrations of the slow defect component in compensated n-type silicon only depend on the interstitial oxygen concentration and on neither the boron concentration nor the equilibrium electron concentration n{sub 0}. The final concentrations of the fast defect component slightly increase with increasing boron concentration. The results on n-type silicon give new insight to the origin of the BO defect and question the existing models for the defect composition.

  6. A 20-40 MHz low-power clock oscillator with open-loop frequency calibration and temperature compensation

    NASA Astrophysics Data System (ADS)

    Lee, Dongsoo; Kim, Hongjin; Lee, Kang-Yoon

    2014-05-01

    In this paper, a 20-40 MHz low-power clock oscillator is presented to provide the frequency reference in data interface applications. The frequency source is referenced to a frequency-calibrated and temperature-compensated 2.5 GHz LC VCO that is implemented with a bondwire inductor. Class-C type VCO is adopted in order to improve the phase noise and reduce the current consumption. A full digital frequency calibration circuit is proposed to cover the wide output frequency range minimizing the frequency variation. External crystal oscillator (REF_CLK) is used only for the absolute frequency calibration at the initial programming stage and is not needed after the programming stage. On the other hand, temperature compensation is performed in an analogue way by controlling the varactor in the LC VCO. This chip is fabricated using 0.18-µm CMOS with the option of lateral PNP transistor. Lateral PNP transistors are used in the temperature compensation circuits. It can be implemented laterally in standard CMOS process. The power consumption is 4.8 mW from a 1.8 V supply. The accuracy of the frequency is ±58 ppm from -20°C to 80°C. The nominal phase noise at 1 MHz and period jitter is -122 dBc/Hz and 2 ps, respectively, when the output frequency is 25 MHz.

  7. Effects of V2G Reactive Power Compensation on the Component Selection in an EV or PHEV Bidirectional Charger

    SciTech Connect

    Kisacikoglu, Mithat C; Ozpineci, Burak; Tolbert, Leon M

    2010-01-01

    Electric vehicles (EVs) and plug-in hybrid electric vehicles (PHEVs) are becoming a part of the electric grid day by day. Chargers for these vehicles have the ability to make this interaction better for the consumer and for the grid. Vehicle to grid (V2G) power transfer has been under research for more than a decade because of the large energy reserve of an electric vehicle battery and the potential of thousands of these connected to the grid. Rather than discharging the vehicle batteries, reactive power compensation in particular is beneficial for both consumers and for the utility. However, certain adverse effects or requirements of reactive power transfer should be defined before a design stage. To understand the dynamics of this operation, this study investigates the effect of reactive power transfer on the charger system components, especially on the dc-link capacitor and the battery.

  8. About compensation the electronic beam dynamic stratification influence in super-power relativistic Cherenkov oscillators

    SciTech Connect

    Kurayev, Alexander A.; Rak, Alexey O.; Sinitsyn, Anatoly K.

    2011-07-01

    On the basis of the exact nonlinear theory relativistic TWT and BWO on irregular hollow waveguides with cathode filters-modulators with the account as propagating, and beyond cut-off waves, with the account of losses in walls of a waveguide and inhomogeneity directing an electronic beam magnetostatic fields finds out influence of dynamic stratification influence on efficiency of the generator. Possibility of almost fill compensation the electronic beam dynamic stratification influence on efficiency by optimization of an electronic beam arrangement in inhomogeneous high frequency and magnetic fields and characteristics of the irregular corrugated waveguide is shown. (author)

  9. Dynamic compensation of the Silver self-powered neutron detector in the ramp program at the OSIRIS reactor

    SciTech Connect

    Moulin, D.J.

    1994-12-31

    The Silver self-powered neutron detector (SPND) is a common detector used in the ramp program at the OSIRIS reactor. The Silver SPND signal is a reference during steady states, but its response is too slow for monitoring transient tests. In order to compensate for the inherent time delay a mathematical processing method of the Silver SPND signal was developed. Based on a convolution-type resolution of the kinetics equations, a dynamic compensation algorithm can be used for transient conditions as well as steady state conditions. A computer program reconstructs, in real-time, the dynamic neutron flux sensed by the Silver detector from the current measured between the emitter and the collector of the SPND. Although this method decreases slightly the signal-to-noise ratio, it maintains the SPND`s characteristics and reduces the response time from about 10 minutes to less than 4 seconds for a step change in flux. This provides for prompt and accurate measurement of fuel rod power during ramp experiments in the OSIRIS reactor. This development makes the Silver SPND very suitable for many on-line monitoring applications.

  10. Innovation on Energy Power Technology (20)Development of Self-commutated Static Var Compensator (STATCOM) and its Practical Application

    NASA Astrophysics Data System (ADS)

    Takeda, Masatoshi

    The self-commutated Static Var Compensator (STATCOM) is expected as one of the most effective tools to enhance power system stability and has been applied world-widely in recent years. Since the first prototype of STATCOM was developed in Japan in 1980, continual efforts by utilities and manufactures drove the development forward to the practical application of STATCOM, resulting in the world-first application of 80MVA STATCOM using GTO thyristors in 1991, followed by the 80MVA STATCOM using GCT thyristors in 2003. Since then, the application of STATCOM has been extended to not only power utility systems but also industrial systems. This paper describes historical development events and engineer's efforts to develop the STATCOM, including some episodes.

  11. Three-dimensional Reluctance Network Analysis of an EIE-Core Variable Inductor and Application to Reactive Power Compensation in a Distribution System

    NASA Astrophysics Data System (ADS)

    Nakamura, Kenji; Ohinata, Takashi; Arimatsu, Kenji; Sakamoto, Kunio; Ichinokura, Osamu

    This paper describes a three-dimensional reluctance network analysis (RNA) of an EIE-core variable inductor, which can be applied as a reactive power compensator in electric power systems. First, a three-dimensional RNA model of an EIE-core considering the magnetic saturation and iron loss is presented. Using the proposed RNA model with external electric circuits, operating characteristics of the variable inductor including the iron loss are calculated accurately. Next, high performance of a 6.6 kV-300 kVA reactive power compensator using the EIE-core variable inductor is demonstrated in a distribution system.

  12. Wave activated power generation system

    SciTech Connect

    Ono, Y.

    1983-08-09

    A wave activated power generation system of the float type is disclosed, comprising at least one piston-cylinder device having an anchored cylinder and a piston slidable in the cylinder and cooperating with the cylinder to form a pumping chamber above the piston and a low pressure chamber below the piston. The cylinder has an intake port and an exhaust port both formed at an upper port thereof to communicate with the pumping chamber and each provided with a check valve. A float is connected through a cable to the piston of the piston- cylinder device. A pair of fluid storages are connected to the intake port and the exhaust port of the pumping chamber, respectively. A waterwheel generator is driven by the fluid flowing from one of the fluid storages to another. A pressure regulating device is connected to the low pressure chamber so as to maintain the low pressure chamber at a pressure lower than the pressure in the pumping chamber, the difference in pressure ceaselessly applying a downward force on the piston to keep the cable in a tensed condition.

  13. Method for determination of the degree of compensation for electrically active impurities in multivalley semiconductors

    SciTech Connect

    Baranskii, P. I.; Gaidar, G. P.

    2013-06-15

    A method for determination of the degree of compensation k = N{sub a}/N{sub d} for shallow impurities in n-Si crystals with a nondegenerate electron gas is suggested. Data facilitating practical determination of the degree of compensation are given.

  14. Reliability of IGBT in a STATCOM for Harmonic Compensation and Power Factor Correction

    SciTech Connect

    Gopi Reddy, Lakshmi Reddy; Tolbert, Leon M; Ozpineci, Burak; Xu, Yan; Rizy, D Tom

    2012-01-01

    With smart grid integration, there is a need to characterize reliability of a power system by including reliability of power semiconductors in grid related applications. In this paper, the reliability of IGBTs in a STATCOM application is presented for two different applications, power factor correction and harmonic elimination. The STATCOM model is developed in EMTP, and analytical equations for average conduction losses in an IGBT and a diode are derived and compared with experimental data. A commonly used reliability model is used to predict reliability of IGBT.

  15. Active Power Controls from Wind Power: Bridging the Gaps

    SciTech Connect

    Ela, E.; Gevorgian, V.; Fleming, P.; Zhang, Y. C.; Singh, M.; Muljadi, E.; Scholbrook, A.; Aho, J.; Buckspan, A.; Pao, L.; Singhvi, V.; Tuohy, A.; Pourbeik, P.; Brooks, D.; Bhatt, N.

    2014-01-01

    This paper details a comprehensive study undertaken by the National Renewable Energy Laboratory, Electric Power Research Institute, and the University of Colorado to understand how the contribution of wind power providing active power control (APC) can benefit the total power system economics, increase revenue streams, improve the reliability and security of the power system, and provide superior and efficient response while reducing any structural and loading impacts that may reduce the life of the wind turbine or its components. The study includes power system simulations, control simulations, and actual field tests using turbines at NREL's National Wind Technology Center (NWTC). The study focuses on synthetic inertial control, primary frequency control, and automatic generation control, and analyzes timeframes ranging from milliseconds to minutes to the lifetime of wind turbines, locational scope ranging from components of turbines to large wind plants to entire synchronous interconnections, and additional topics ranging from economics to power system engineering to control design.

  16. High power operation of a nitrogen doped, vanadium compensated, 6H-SiC extrinsic photoconductive switch

    SciTech Connect

    Sullivan, J. S.

    2014-04-28

    We report the high power operation of nitrogen doped, vanadium compensated, 6H-SiC, extrinsic photoconductive switches with improved vanadium and nitrogen dopant density. Photoconductive switching tests are performed on 1 mm thick, m-plane, switch substrates at switch voltage and currents up to 17 kV and 1.5 kA, respectively. Sub-ohm minimum switch on resistance is achieved for peak optical intensities ≥35 MW/cm{sup 2} at 532 nm applied to the switch facet. A reduction of greater than nine orders of magnitude is observed in switch material resistivity between dark and illuminated states.

  17. 34 CFR 222.22 - How does the Secretary treat compensation from Federal activities for purposes of determining...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false How does the Secretary treat compensation from Federal activities for purposes of determining eligibility and payments? 222.22 Section 222.22 Education Regulations of the Offices of the Department of Education OFFICE OF ELEMENTARY AND SECONDARY EDUCATION, DEPARTMENT OF EDUCATION IMPACT AID...

  18. Molybdenum substitution for improving the charge compensation and activity of Li2MnO3.

    PubMed

    Ma, Jun; Zhou, Yong-Ning; Gao, Yurui; Kong, Qingyu; Wang, Zhaoxiang; Yang, Xiao-Qing; Chen, Liquan

    2014-07-01

    Lithium-rich layer-structured oxides xLi2 MnO3 ⋅ (1-x)LiMO2 (0compensation contributed by O(2-) in Li2 MnO3 leads to the evolution of oxygen during the initial Li(+) ion extraction at high voltage and voltage fading in subsequent cycling, resulting in a safety hazard and poor cycling performance of the battery. Molybdenum substitution was performed in this work to provide another electron donor and to enhance the electrochemical activity of Li2 MnO3 -based cathode materials. X-ray diffraction and adsorption studies indicated that Mo(5+) substitution expands the unit cell in the crystal lattice and weakens the LiO and MnO bonds, as well as enhancing the activity of Li2 MnO3 by lowering its delithiation potential and suppressing the release of oxygen. In addition, the chemical environment of O(2-) ions in molybdenum-substituted Li2 MnO3 is more reversible than in the unsubstituted sample during cycling. Therefore molybdenum substitution is expected to improve the performances of the Li2 MnO3 -based lithium-rich cathode materials. PMID:24939463

  19. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1987-04-20

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolyte rendering the electrolyte electrochemically active. 2 figs.

  20. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, William B.; Graham, Robert A.; Morosin, Bruno

    1988-01-01

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active.

  1. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1988-11-08

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active. 2 figs.

  2. 76 FR 67259 - Frequency Regulation Compensation in the Organized Wholesale Power Markets

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-31

    ... Markets, 76 FR 11,177, 134 FERC ] 61,124 (2011) (NOPR). \\18\\ See Appendix for a list of commenters. II... up 100 percent of the NO X emission reduction expected from introducing wind and solar power will be..., 2011 Comments at 13 (citing Katzenstein, W., and Jay Apt. Air Emissions Due To Wind and Solar...

  3. Frequency Splitting Analysis and Compensation Method for Inductive Wireless Powering of Implantable Biosensors.

    PubMed

    Schormans, Matthew; Valente, Virgilio; Demosthenous, Andreas

    2016-01-01

    Inductive powering for implanted medical devices, such as implantable biosensors, is a safe and effective technique that allows power to be delivered to implants wirelessly, avoiding the use of transcutaneous wires or implanted batteries. Wireless powering is very sensitive to a number of link parameters, including coil distance, alignment, shape, and load conditions. The optimum drive frequency of an inductive link varies depending on the coil spacing and load. This paper presents an optimum frequency tracking (OFT) method, in which an inductive power link is driven at a frequency that is maintained at an optimum value to ensure that the link is working at resonance, and the output voltage is maximised. The method is shown to provide significant improvements in maintained secondary voltage and system efficiency for a range of loads when the link is overcoupled. The OFT method does not require the use of variable capacitors or inductors. When tested at frequencies around a nominal frequency of 5 MHz, the OFT method provides up to a twofold efficiency improvement compared to a fixed frequency drive. The system can be readily interfaced with passive implants or implantable biosensors, and lends itself to interfacing with designs such as distributed implanted sensor networks, where each implant is operating at a different frequency. PMID:27527174

  4. Power to Production: Activity Guide.

    ERIC Educational Resources Information Center

    Massachusetts Univ., Lowell. Tsongas Industrial History Center.

    This field trip program consists of a 90-minute interpretive tour and a 90-minute hands-on workshop. The tour and workshop explore the role of water power in the Industrial Revolution. On the tour, students discover firsthand the unique resources of Lowell, Massachusetts, and the Park, while the workshop brings these historic resources to life as…

  5. [Communication and noise. Speech intelligibility of airplane pilots with and without active noise compensation].

    PubMed

    Matschke, R G

    1994-08-01

    Noise exposure measurements were performed with pilots of the German Federal Navy during flight situations. The ambient noise levels during regular flight were maintained at levels above a 90 dB A-weighted level. This noise intensity requires wearing ear protection to avoid sound-induced hearing loss. To be able to understand radio communication (ATC) in spite of a noisy environment, headphone volume must be raised above the noise of the engines. The use of ear plugs in addition to the headsets and flight helmets is only of limited value because personal ear protection affects the intelligibility of ATC. Whereas speech intelligibility of pilots with normal hearing is affected to only a smaller degree, pilots with pre-existing high-frequency hearing losses show substantial impairments of speech intelligibility that vary in proportion to the hearing deficit present. Communication abilities can be reduced drastically, which in turn can affect air traffic security. The development of active noise compensation devices (ANC) that make use of the "anti-noise" principle may be a solution to this dilemma. To evaluate the effectiveness of an ANC-system and its influence on speech intelligibility, speech audiometry was performed with a German standardized test during simulated flight conditions with helicopter pilots. Results demonstrate the helpful effect on speech understanding especially for pilots with noise-induced hearing losses. This may help to avoid pre-retirement professional disability. PMID:7960953

  6. Mantle compensation of active metamorphic core complexes at Woodlark rift in Papua New Guinea.

    PubMed

    Abers, Geoffrey A; Ferris, Aaron; Craig, Mitchell; Davies, Hugh; Lerner-Lam, Arthur L; Mutter, John C; Taylor, Brian

    2002-08-22

    In many highly extended rifts on the Earth, tectonic removal of the upper crust exhumes mid-crustal rocks, producing metamorphic core complexes. These structures allow the upper continental crust to accommodate tens of kilometres of extension, but it is not clear how the lower crust and underlying mantle respond. Also, despite removal of the upper crust, such core complexes remain both topographically high and in isostatic equilibrium. Because many core complexes in the western United States are underlain by a flat Moho discontinuity, it has been widely assumed that their elevation is supported by flow in the lower crust or by magmatic underplating. These processes should decouple upper-crust extension from that in the mantle. In contrast, here we present seismic observations of metamorphic core complexes of the western Woodlark rift that show the overall crust to be thinned beneath regions of greatest surface extension. These core complexes are actively being exhumed at a rate of 5-10 km Myr(-1), and the thinning of the underlying crust appears to be compensated by mantle rocks of anomalously low density, as indicated by low seismic velocities. We conclude that, at least in this case, the development of metamorphic core complexes and the accommodation of high extension is not purely a crustal phenomenon, but must involve mantle extension. PMID:12192406

  7. Development and Psychometric Properties of the Instrumental Activities of Daily Living: Compensation Scale

    PubMed Central

    Schmitter-Edgecombe, Maureen; Parsey, Carolyn; Lamb, Richard

    2014-01-01

    The Instrumental Activities of Daily Living – Compensation (IADL-C) scale was developed to capture early functional difficulties and to quantify compensatory strategy use that may mitigate functional decline in the aging population. The IADL-C was validated in a sample of cognitively healthy older adults (N=184) and individuals with mild cognitive impairment (MCI; N=92) and dementia (N=24). Factor analysis and Rasch item analysis led to the 27-item IADL-C informant questionnaire with four functional domain subscales (money and self-management, home daily living, travel and event memory, and social skills). The subscales demonstrated good internal consistency (Rasch reliability 0.80 to 0.93) and test-retest reliability (Spearman coefficients 0.70 to 0.91). The IADL-C total score and subscales showed convergent validity with other IADL measures, discriminant validity with psychosocial measures, and the ability to discriminate between diagnostic groups. The money and self management subscale showed notable difficulties for individuals with MCI, whereas difficulties with home daily living became more prominent for dementia participants. Compensatory strategy use increased in the MCI group and decreased in the dementia group. PMID:25344901

  8. High-contrast imaging with an arbitrary aperture: Active compensation of aperture discontinuities

    SciTech Connect

    Pueyo, Laurent; Norman, Colin

    2013-06-01

    We present a new method to achieve high-contrast images using segmented and/or on-axis telescopes. Our approach relies on using two sequential deformable mirrors (DMs) to compensate for the large amplitude excursions in the telescope aperture due to secondary support structures and/or segment gaps. In this configuration the parameter landscape of DM surfaces that yield high-contrast point-spread functions is not linear, and nonlinear methods are needed to find the true minimum in the optimization topology. We solve the highly nonlinear Monge-Ampere equation that is the fundamental equation describing the physics of phase-induced amplitude modulation. We determine the optimum configuration for our two sequential DM system and show that high-throughput and high-contrast solutions can be achieved using realistic surface deformations that are accessible using existing technologies. We name this process Active Compensation of Aperture Discontinuities (ACAD). We show that for geometries similar to the James Webb Space Telescope, ACAD can attain at least 10{sup –7} in contrast and an order of magnitude higher for both the future extremely large telescopes and on-axis architectures reminiscent of the Hubble Space Telescope. We show that the converging nonlinear mappings resulting from our DM shapes actually damp near-field diffraction artifacts in the vicinity of the discontinuities. Thus, ACAD actually lowers the chromatic ringing due to diffraction by segment gaps and struts while not amplifying the diffraction at the aperture edges beyond the Fresnel regime. This outer Fresnel ringing can be mitigated by properly designing the optical system. Consequently, ACAD is a true broadband solution to the problem of high-contrast imaging with segmented and/or on-axis apertures. We finally show that once the nonlinear solution is found, fine tuning with linear methods used in wavefront control can be applied to further contrast by another order of magnitude. Generally speaking

  9. 78 FR 68780 - Treatment of Income From Indian Fishing Rights-Related Activity as Compensation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-15

    ... Executive Order 13563. Therefore, a regulatory assessment is not required. It has also been determined that... subject to a substantial risk of forfeiture. Section 1.415(c)-2(c)(3) excludes from compensation...

  10. Resistance of Cancer Cells to Targeted Therapies Through the Activation of Compensating Signaling Loops.

    PubMed

    von Manstein, Viktoria; Yang, Chul Min; Richter, Diane; Delis, Natalia; Vafaizadeh, Vida; Groner, Bernd

    2013-12-01

    The emergence of low molecular weight kinase inhibitors as "targeted" drugs has led to remarkable advances in the treatment of cancer patients. The clinical benefits of these tumor therapies, however, vary widely in patient populations and with duration of treatment. Intrinsic and acquired resistance against such drugs limits their efficacy. In addition to the well studied mechanisms of resistance based upon drug transport and metabolism, genetic alterations in drug target structures and the activation of compensatory cell signaling have received recent attention. Adaptive responses can be triggered which counteract the initial dependence of tumor cells upon a particular signaling molecule and allow only a transient inhibition of tumor cell growth. These compensating signaling mechanisms are often based upon the relief of repression of regulatory feedback loops. They might involve cell autonomous, intracellular events or they can be mediated via the secretion of growth factor receptor ligands into the tumor microenvironment and signal induction in an auto- or paracrine fashion. The transcription factors Stat3 and Stat5 mediate the biological functions of cytokines, interleukins and growth factors and can be considered as endpoints of multiple signaling pathways. In normal cells this activation is transient and the Stat molecules return to their non-phosphorylated state within a short time period. In tumor cells the balance between activating and de-activating signals is disturbed resulting in the persistent activation of Stat3 or Stat5. The constant activation of Stat3 induces the expression of target genes, which cause the proliferation and survival of cancer cells, as well as their migration and invasive behavior. Activating components of the Jak-Stat pathway have been recognized as potentially valuable drug targets and important principles of compensatory signaling circuit induction during targeted drug treatment have been discovered in the context of kinase

  11. A flexible active and reactive power control strategy for a variable speed constant frequency generating system

    SciTech Connect

    Tang, Y.; Xu, L.

    1995-07-01

    Variable-speed constant-frequency generating systems are used in wind power, hydro power, aerospace, and naval power generations to enhance efficiency and reduce friction. In these applications, an attractive candidate is the slip power recovery system comprising of doubly excited induction machine or doubly excited brushless reluctance machine and PWM converters with a dc link. In this paper, a flexible active and reactive power control strategy is developed, such that the optimal torque-speed profile of the turbine can be followed and overall reactive power can be controlled, while the machine copper losses have been minimized. At the same time, harmonics injected into the power network has also been minimized. In this manner, the system can function as both a high-efficient power generator and a flexible reactive power compensator.

  12. Method for beam steering compensation in an ultra-high power liquid laser

    DOEpatents

    Ault, Earl R.

    2002-01-01

    Thermally induced distortion of the optical wavefront caused by heating of the laser media by waste heat from the excitation process and absorption of laser radiation creates optical phase errors. A system generates an error signal derived from the optical phase errors. The error signal is fed back to the power supplies driving semiconductor diodes that excite the lasing liquid thereby introducing an electrically controllable wedge into the optical cavity to correct the optical phase errors.

  13. Simulation of selective passive compensation

    SciTech Connect

    Spikings, C.R.; Putley, D. )

    1991-01-01

    Compulsators have attracted a great deal of interest over the last few years as a way of providing repetitive high current millisecond pulses. The compulsator stores energy in a rotational form and works on a similar principle to a conventional alternator except that its internal impedance is reduced through compensating currents allowing greater currents to be drawn. This paper presents the theory behind selective passive compensation and presents some results from the computer simulation of a railgun powered by a selective passive compulsator. These results show that compulsator can be configured to produce flat topped current pulses into a railgun load. A test compulsator with active compensation has previously been designed and built by Culham Laboratory.

  14. 18 CFR 1317.515 - Compensation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 2 2013-04-01 2012-04-01 true Compensation. 1317.515... THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities Prohibited §...

  15. 18 CFR 1317.515 - Compensation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 2 2012-04-01 2012-04-01 false Compensation. 1317.515... THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities Prohibited §...

  16. 18 CFR 1317.515 - Compensation.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 2 2014-04-01 2014-04-01 false Compensation. 1317.515... THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities Prohibited §...

  17. GABAA-receptor activation in the subthalamic nucleus compensates behavioral asymmetries in the hemiparkinsonian rat.

    PubMed

    Petri, David; Pum, Martin; Vesper, Jan; Huston, Joseph P; Schnitzler, Alfons

    2013-09-01

    The subthalamic nucleus (STN) has a pivotal role in the pathophysiology of Parkinson's disease (PD). Modulation of STN activity (by lesions, pharmacological or electrical stimulation) has been shown to improve motor parameters in PD patients and in animal models of PD. In an attempt to characterize the neurochemical bases for such antiparkinsonian action, we address specific neurotransmitter systems via local pharmacological manipulation of the STN in hemiparkinsonian rats. Here, we have focused on the GABAergic and glutamatergic receptors in the STN. In animals with unilateral 6-hydroxydopamine lesions of the nigro-striatal tract, we administered either the selective GABAA-agonist muscimol (0.5 μg and 1.0 μg), the non-competitive N-methyl-d-aspartate (NMDA)-antagonist MK-801 (dizocilpine; 2.5 μg), or vehicle (0.25 μl) into the STN. The effects of GABAergic and glutamatergic modulation of the STN on motor parameters were assessed by gauging rotational behavior and locomotion. Application of muscimol ipsilateral to the side of dopamine-depletion influenced turning behavior in a dose-dependent fashion, with the low dose re-adjusting turning behavior to a non-biased distribution, and the high dose evoking contraversive turning. The administration of MK-801 did not have such effects. These findings give evidence for the involvement of GABAergic activation in the STN in the compensation of motor asymmetries in the hemiparkinsonian rat, whereas N-methyl-d-aspartate (NMDA)-antagonism was ineffective in this model of PD. PMID:23727148

  18. SiC MOSFET Based Single Phase Active Boost Rectifier with Power Factor Correction for Wireless Power Transfer Applications

    SciTech Connect

    Onar, Omer C; Tang, Lixin; Chinthavali, Madhu Sudhan; Campbell, Steven L; Miller , John M.

    2014-01-01

    Wireless Power Transfer (WPT) technology is a novel research area in the charging technology that bridges the utility and the automotive industries. There are various solutions that are currently being evaluated by several research teams to find the most efficient way to manage the power flow from the grid to the vehicle energy storage system. There are different control parameters that can be utilized to compensate for the change in the impedance due to variable parameters such as battery state-of-charge, coupling factor, and coil misalignment. This paper presents the implementation of an active front-end rectifier on the grid side for power factor control and voltage boost capability for load power regulation. The proposed SiC MOSFET based single phase active front end rectifier with PFC resulted in >97% efficiency at 137mm air-gap and >95% efficiency at 160mm air-gap.

  19. Multi-channel programmable power supply with temperature compensation for silicon sensors

    NASA Astrophysics Data System (ADS)

    Shukla, R. A.; Achanta, V. G.; Dugad, S. R.; Freeman, J.; Garde, C. S.; Gupta, S. K.; Khandekar, P. D.; Kurup, A. M.; Lokhandwala, S. S.; Los, S.; Prabhu, S. S.; Rakshe, P. S.

    2016-01-01

    Silicon Photo-Multipliers (SiPMs) are increasingly becoming popular for discrete photon counting applications due to the wealth of advantages they offer over conventional photo-detectors such as photo-multiplier tubes and hybrid photo-diodes. SiPMs are used in variety of applications ranging from high energy physics and nuclear physics experiments to medical diagnostics. The gain of a SiPM is directly proportional to the difference between applied and breakdown voltage of the device. However, the breakdown voltage depends critically on the ambient temperature and has a large temperature co-efficient in the range of 40-60 mV/°C resulting in a typical gain variation of 3%-5%/°C [Dinu et al., in IEEE Nuclear Science Symposium, Medical Imaging Conference and 17th Room Temperature Semiconductor Detector Workshop (IEEE, 2010), p. 215]. We plan to use the SiPM as a replacement for PMT in the cosmic ray experiment (GRAPES-3) at Ooty [Gupta et al., Nucl. Instrum. Methods Phys. Res., Sect. A 540, 311 (2005)]. There the SiPMs will be operated in an outdoor environment subjected to temperature variation of about 15 °C over a day. A gain variation of more than 50% was observed for such large variations in the temperature. To stabilize the gain of the SiPM under such operating conditions, a low-cost, multi-channel programmable power supply (0-90 V) was designed that simultaneously provides the bias voltage to 16 SiPMs. The programmable power supply (PPS) was designed to automatically adjust the operating voltage for each channel with a built-in closed loop temperature feedback mechanism. The PPS provides bias voltage with a precision of 6 mV and measures the load current with a precision of 1 nA. Using this PPS, a gain stability of 0.5% for SiPM (Hamamatsu, S10931-050P) has been demonstrated over a wide temperature range of 15 °C. The design methodology of the PPS system, its validation, and the results of the tests carried out on the SiPM is presented in this article. The

  20. Multi-channel programmable power supply with temperature compensation for silicon sensors.

    PubMed

    Shukla, R A; Achanta, V G; Dugad, S R; Freeman, J; Garde, C S; Gupta, S K; Khandekar, P D; Kurup, A M; Lokhandwala, S S; Los, S; Prabhu, S S; Rakshe, P S

    2016-01-01

    Silicon Photo-Multipliers (SiPMs) are increasingly becoming popular for discrete photon counting applications due to the wealth of advantages they offer over conventional photo-detectors such as photo-multiplier tubes and hybrid photo-diodes. SiPMs are used in variety of applications ranging from high energy physics and nuclear physics experiments to medical diagnostics. The gain of a SiPM is directly proportional to the difference between applied and breakdown voltage of the device. However, the breakdown voltage depends critically on the ambient temperature and has a large temperature co-efficient in the range of 40-60 mV/°C resulting in a typical gain variation of 3%-5%/°C [Dinu et al., in IEEE Nuclear Science Symposium, Medical Imaging Conference and 17th Room Temperature Semiconductor Detector Workshop (IEEE, 2010), p. 215]. We plan to use the SiPM as a replacement for PMT in the cosmic ray experiment (GRAPES-3) at Ooty [Gupta et al., Nucl. Instrum. Methods Phys. Res., Sect. A 540, 311 (2005)]. There the SiPMs will be operated in an outdoor environment subjected to temperature variation of about 15 °C over a day. A gain variation of more than 50% was observed for such large variations in the temperature. To stabilize the gain of the SiPM under such operating conditions, a low-cost, multi-channel programmable power supply (0-90 V) was designed that simultaneously provides the bias voltage to 16 SiPMs. The programmable power supply (PPS) was designed to automatically adjust the operating voltage for each channel with a built-in closed loop temperature feedback mechanism. The PPS provides bias voltage with a precision of 6 mV and measures the load current with a precision of 1 nA. Using this PPS, a gain stability of 0.5% for SiPM (Hamamatsu, S10931-050P) has been demonstrated over a wide temperature range of 15 °C. The design methodology of the PPS system, its validation, and the results of the tests carried out on the SiPM is presented in this

  1. Detection of and Compensation for EMG Disturbances for Powered Lower Limb Prosthesis Control.

    PubMed

    Spanias, John A; Perreault, Eric J; Hargrove, Levi J

    2016-02-01

    Myoelectric pattern recognition algorithms have been proposed for the control of powered lower limb prostheses, but electromyography (EMG) signal disturbances remain an obstacle to clinical implementation. To address this problem, we used a log-likelihood metric to detect simulated EMG disturbances and real disturbances acquired from EMG containing electrode shift. We found that features extracted from disturbed EMG have much lower log likelihoods than those from undisturbed signals and can be detected using a single threshold acquired from the training data. We designed a linear discriminant analysis (LDA) classifier that uses the log likelihood to decide between using a combination of EMG and mechanical sensors and using mechanical sensors only, to predict locomotion modes. When EMG contained disturbances, our classifier detected those disturbances and disregarded EMG data. Our classifier had significantly lower errors than a standard LDA classifier in the presence of EMG disturbances. The log-likelihood classifier had a low false positive threshold, and thus did not perform significantly differently from the standard LDA classifier when EMG did not contain disturbances. The log-likelihood threshold could also be applied to individual EMG channels, enabling specific channels containing EMG disturbances to be appropriately ignored when making locomotion mode predictions. PMID:25826807

  2. Rational positive real approximations for LQG optimal compensators arising in active stabilization of flexible structures

    NASA Technical Reports Server (NTRS)

    Desantis, A.

    1994-01-01

    In this paper the approximation problem for a class of optimal compensators for flexible structures is considered. The particular case of a simply supported truss with an offset antenna is dealt with. The nonrational positive real optimal compensator transfer function is determined, and it is proposed that an approximation scheme based on a continued fraction expansion method be used. Comparison with the more popular modal expansion technique is performed in terms of stability margin and parameters sensitivity of the relative approximated closed loop transfer functions.

  3. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: II. Solutions and applications

    SciTech Connect

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-01

    In a companion manuscript, we developed a novel optimization method for placement, sizing, and operation of Flexible Alternating Current Transmission System (FACTS) devices to relieve transmission network congestion. Specifically, we addressed FACTS that provide Series Compensation (SC) via modification of line inductance. In this manuscript, this heuristic algorithm and its solutions are explored on a number of test cases: a 30-bus test network and a realistically-sized model of the Polish grid (~ 2700 nodes and ~ 3300 lines). The results on the 30-bus network are used to study the general properties of the solutions including non-locality and sparsity. The Polish grid is used as a demonstration of the computational efficiency of the heuristics that leverages sequential linearization of power flow constraints and cutting plane methods that take advantage of the sparse nature of the SC placement solutions. Using these approaches, the algorithm is able to solve an instance of Polish grid in tens of seconds. We explore the utility of the algorithm by analyzing transmission networks congested by (a) uniform load growth, (b) multiple overloaded configurations, and (c) sequential generator retirements.

  4. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: II. Solutions and applications

    NASA Astrophysics Data System (ADS)

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-01

    In a companion manuscript (Frolov et al 2014 New J. Phys. 16 art. no.) , we developed a novel optimization method for the placement, sizing, and operation of flexible alternating current transmission system (FACTS) devices to relieve transmission network congestion. Specifically, we addressed FACTS that provide series compensation (SC) via modification of line inductance. In this sequel manuscript, this heuristic algorithm and its solutions are explored on a number of test cases: a 30-bus test network and a realistically-sized model of the Polish grid (˜2700 nodes and ˜3300 lines). The results from the 30-bus network are used to study the general properties of the solutions, including nonlocality and sparsity. The Polish grid is used to demonstrate the computational efficiency of the heuristics that leverage sequential linearization of power flow constraints, and cutting plane methods that take advantage of the sparse nature of the SC placement solutions. Using these approaches, we can use the algorithm to solve a Polish transmission grid in tens of seconds. We explore the utility of the algorithm by analyzing transmission networks congested by (i) uniform load growth, (ii) multiple overloaded configurations, and (iii) sequential generator retirements.

  5. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: I. Model implementation

    SciTech Connect

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-24

    We explore optimization methods for planning the placement, sizing and operations of Flexible Alternating Current Transmission System (FACTS) devices installed to relieve transmission grid congestion. We limit our selection of FACTS devices to Series Compensation (SC) devices that can be represented by modification of the inductance of transmission lines. Our master optimization problem minimizes the l1 norm of the inductance modification subject to the usual line thermal-limit constraints. We develop heuristics that reduce this non-convex optimization to a succession of Linear Programs (LP) which are accelerated further using cutting plane methods. The algorithm solves an instance of the MatPower Polish Grid model (3299 lines and 2746 nodes) in 40 seconds per iteration on a standard laptop—a speed up that allows the sizing and placement of a family of SC devices to correct a large set of anticipated congestions. We observe that our algorithm finds feasible solutions that are always sparse, i.e., SC devices are placed on only a few lines. In a companion manuscript, we demonstrate our approach on realistically-sized networks that suffer congestion from a range of causes including generator retirement. In this manuscript, we focus on the development of our approach, investigate its structure on a small test system subject to congestion from uniform load growth, and demonstrate computational efficiency on a realistically-sized network.

  6. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: II. Solutions and applications

    DOE PAGESBeta

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-01

    In a companion manuscript, we developed a novel optimization method for placement, sizing, and operation of Flexible Alternating Current Transmission System (FACTS) devices to relieve transmission network congestion. Specifically, we addressed FACTS that provide Series Compensation (SC) via modification of line inductance. In this manuscript, this heuristic algorithm and its solutions are explored on a number of test cases: a 30-bus test network and a realistically-sized model of the Polish grid (~ 2700 nodes and ~ 3300 lines). The results on the 30-bus network are used to study the general properties of the solutions including non-locality and sparsity. The Polishmore » grid is used as a demonstration of the computational efficiency of the heuristics that leverages sequential linearization of power flow constraints and cutting plane methods that take advantage of the sparse nature of the SC placement solutions. Using these approaches, the algorithm is able to solve an instance of Polish grid in tens of seconds. We explore the utility of the algorithm by analyzing transmission networks congested by (a) uniform load growth, (b) multiple overloaded configurations, and (c) sequential generator retirements.« less

  7. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: I. Model implementation

    DOE PAGESBeta

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-24

    We explore optimization methods for planning the placement, sizing and operations of Flexible Alternating Current Transmission System (FACTS) devices installed to relieve transmission grid congestion. We limit our selection of FACTS devices to Series Compensation (SC) devices that can be represented by modification of the inductance of transmission lines. Our master optimization problem minimizes the l1 norm of the inductance modification subject to the usual line thermal-limit constraints. We develop heuristics that reduce this non-convex optimization to a succession of Linear Programs (LP) which are accelerated further using cutting plane methods. The algorithm solves an instance of the MatPower Polishmore » Grid model (3299 lines and 2746 nodes) in 40 seconds per iteration on a standard laptop—a speed up that allows the sizing and placement of a family of SC devices to correct a large set of anticipated congestions. We observe that our algorithm finds feasible solutions that are always sparse, i.e., SC devices are placed on only a few lines. In a companion manuscript, we demonstrate our approach on realistically-sized networks that suffer congestion from a range of causes including generator retirement. In this manuscript, we focus on the development of our approach, investigate its structure on a small test system subject to congestion from uniform load growth, and demonstrate computational efficiency on a realistically-sized network.« less

  8. Efficient algorithm for locating and sizing series compensation devices in large power transmission grids: I. Model implementation

    NASA Astrophysics Data System (ADS)

    Frolov, Vladimir; Backhaus, Scott; Chertkov, Misha

    2014-10-01

    We explore optimization methods for planning the placement, sizing and operations of flexible alternating current transmission system (FACTS) devices installed to relieve transmission grid congestion. We limit our selection of FACTS devices to series compensation (SC) devices that can be represented by modification of the inductance of transmission lines. Our master optimization problem minimizes the l1 norm of the inductance modification subject to the usual line thermal-limit constraints. We develop heuristics that reduce this non-convex optimization to a succession of linear programs (LP) that are accelerated further using cutting plane methods. The algorithm solves an instance of the MatPower Polish Grid model (3299 lines and 2746 nodes) in 40 seconds per iteration on a standard laptop—a speed that allows the sizing and placement of a family of SC devices to correct a large set of anticipated congestions. We observe that our algorithm finds feasible solutions that are always sparse, i.e., SC devices are placed on only a few lines. In a companion manuscript, we demonstrate our approach on realistically sized networks that suffer congestion from a range of causes, including generator retirement. In this manuscript, we focus on the development of our approach, investigate its structure on a small test system subject to congestion from uniform load growth, and demonstrate computational efficiency on a realistically sized network.

  9. A Snapshot of Industry and Academic Professional Activities, Compensation, and Engagement in Educational Measurement

    ERIC Educational Resources Information Center

    Packman, Sheryl; Camara, Wayne J.; Huff, Kristen

    2010-01-01

    This paper provides a snapshot of educational measurement professionals--their educational, professional and demographic backgrounds, as well as their workplace settings, job tasks, professional involvement, and compensation practices. Two previous studies have surveyed employers, but this is the first attempt to conduct a comprehensive survey of…

  10. A Student Activity on Visual Resolving Power

    ERIC Educational Resources Information Center

    Warren, T. H.; Henriksen, P. N.; Ramsier, R. D.

    2003-01-01

    We present a simple activity in which students measure the resolving power of their eyes. The approach can be used at various levels of sophistication with students having a wide variety of skills and scientific training. We discuss our experiences using this activity with a class of non-science majors as well as with a group of pre-engineering…

  11. Polymer structure and the compensation effect of the diffusion pre-exponential factor and activation energy of a permeating solute.

    PubMed

    Zheng, Ju-Meng; Qiu, Jun; Madeira, Luis M; Mendes, Adélio

    2007-03-22

    In the present work, the relation between the pre-exponential factor and the apparent activation energy of diffusion, ln D(0) = alpha + betaE(D), so-called compensation effect, is re-examined and critically discussed for diffusion of gases in rubbery and glassy polymers. In principle, the above equation could be derived from the enthalpy-entropy compensation in the framework of the transition state theory. However, one should consider the influence of the jump length term contained in the pre-exponential factor, which may be affected by permeating species and polymer properties. We found that parameter alpha depends on penetrant size and polymer properties, such as local chain mobility and free volume. This can be interpreted by the fact that the jump length is affected by both penetrant and polymer properties. Finally, methods for estimating the jump length are discussed. PMID:17316040

  12. Piezoelectric Power Requirements for Active Vibration Control

    NASA Technical Reports Server (NTRS)

    Brennan, Matthew C.; McGowan, Anna-Maria Rivas

    1997-01-01

    This paper presents a method for predicting the power consumption of piezoelectric actuators utilized for active vibration control. Analytical developments and experimental tests show that the maximum power required to control a structure using surface-bonded piezoelectric actuators is independent of the dynamics between the piezoelectric actuator and the host structure. The results demonstrate that for a perfectly-controlled system, the power consumption is a function of the quantity and type of piezoelectric actuators and the voltage and frequency of the control law output signal. Furthermore, as control effectiveness decreases, the power consumption of the piezoelectric actuators decreases. In addition, experimental results revealed a non-linear behavior in the material properties of piezoelectric actuators. The material non- linearity displayed a significant increase in capacitance with an increase in excitation voltage. Tests show that if the non-linearity of the capacitance was accounted for, a conservative estimate of the power can easily be determined.

  13. Active feed array compensation for reflector antenna surface distortions. Ph.D. Thesis - Akron Univ., Ohio

    NASA Technical Reports Server (NTRS)

    Acosta, Roberto J.

    1988-01-01

    The feasibility of electromagnetic compensation for reflector antenna surface distortions is investigated. The performance characteristics of large satellite communication reflector antenna systems degrade as the reflector surface distorts, mainly due to thermal effects from solar radiation. The technique developed can be used to maintain the antenna boresight directivity and sidelobe level independent of thermal effects on the reflector surface. With the advent of monolithic microwave integrated circuits (MMIC), a greater flexibility in array fed reflector antenna systems can be achieved. MMIC arrays provide independent control of amplitude and phase for each of the many radiating elements in the feed array. By assuming a known surface distortion profile, a simulation study is carried out to examine the antenna performance as a function of feed array size and number of elements. Results indicate that the compensation technique can effectively control boresight directivity and sidelobe level under peak surface distortion in the order of tenth of a wavelength.

  14. Low-power SXGA active matrix OLED

    NASA Astrophysics Data System (ADS)

    Wacyk, Ihor; Prache, Olivier; Ghosh, Amal

    2009-05-01

    This paper presents the design and first evaluation of a full-color 1280×3×1024 pixel, active matrix organic light emitting diode (AMOLED) microdisplay that operates at a low power of 200mW under typical operating conditions of 35fL, and offers a precision 30-bit RGB digital interface in a compact size (0.78-inch diagonal active area). The new system architecture developed by eMagin for the SXGA microdisplay, based on a separate FPGA driver and AMOLED display chip, offers several benefits, including better power efficiency, cost-effectiveness, more features for improved performance, and increased system flexibility.

  15. Control of transient vibrations due to stage movements in 6-dof active pneumatic table by inertial force compensation

    NASA Astrophysics Data System (ADS)

    Sun, Jong-Oh; Kim, Kwang-joon

    2013-10-01

    Passive pneumatic tables are popularly used in precision measurements or processes for isolation of ground vibrations over frequency ranges higher than resonance frequencies of a few Hz typically. Recently, active pneumatic tables are also used often because the passive systems are liable to table excitations in the low resonance frequency ranges, causing long settling times. In studies on the active tables, disturbances onto the tables were often regarded to be unknown and, hence, feedback control algorithms were implemented. However, the disturbances are mostly due to inertial forces due to movement of equipment on the table, e.g., x-y stages. Such a movement is given relative to the table as command inputs. Since absolute motion of the table is normally measured in an active isolation table, absolute motion of the equipment can be easily estimated for calculation of the inertial force exerted onto the table by the moving equipment. Consequently, by compensating dynamic pressure inside the pneumatic chamber to counteract with the inertia force due to the equipment motion, resultant forces acting onto the table can be made zero. In this paper, how to apply the proposed feed-forward control algorithm to a 6-degree of freedom active pneumatic table with time-delay pneumatic control is presented. Performance of the inertial force compensation control evaluated through experiments is also discussed.

  16. [Insufficient legal rights of traffic accident victims. Insurance companies should force more active compensation claims].

    PubMed

    Gullbring, B; Månsson, M; Walheim, G

    2000-11-15

    According to law, persons injured in road traffic accidents are entitled to compensation. In almost 92% of cases, victims accept a modified solution suggested by the insurance company involved. If an agreement cannot be reached, or the disability is 10% or more, the case is referred to The Road Traffic Injuries Commission (TSN). Insurance companies often claim that the lengthy wait for a final ruling--up to four years or more--is due to the lack of a doctor's certificate of disability. PMID:11116870

  17. Study on Reactive Automatic Compensation System Design

    NASA Astrophysics Data System (ADS)

    Zhe, Sun; Qingyang, Liang; Peiqing, Luo; Chenfei, Zhang

    At present, low-voltage side of transformer is public in urban distribution network, as inductive load of household appliances is increasing, the power factor decreased, this lead to a large loss of public transformer low voltage side, the supply voltage indicators can not meet user's requirements. Therefore, the design of reactive power compensation system has become another popular research. This paper introduces the principle of reactive power compensation, analyzes key technologies of reactive power compensation, design an overall program of reactive power automatic compensation system to conquer various deficiencies of reactive power automatic compensation equipment.

  18. Influence of gravity compensation on kinematics and muscle activation patterns during reach and retrieval in subjects with cervical spinal cord injury: an explorative study.

    PubMed

    Kloosterman, Marieke G M; Snoek, Govert J; Kouwenhoven, Mirjam; Nene, Anand V; Jannink, Michiel J A

    2010-01-01

    Many interventions in upper-limb rehabilitation after cervical spinal cord injury (CSCI) use arm support (gravity compensation); however, its specific effects on kinematics and muscle activation characteristics in subjects with a CSCI are largely unknown. We conducted a cross-sectional explorative study to study these effects. Nine subjects with a CSCI performed two goal-directed arm movements (maximal reach, reach and retrieval) with and without gravity compensation. Angles at elbow and shoulder joints and muscle activation were measured and compared. Seven subjects reduced elbow extension (range 1.8°-4.5°) during the maximal reaching task with gravity compensation. In the reach and retrieval task with gravity compensation, all subjects decreased elbow extension (range 0.1°-11.0°). Eight subjects executed movement closer to the body. Regarding muscle activation, gravity compensation did not influence timing; however, the amplitude of activation decreased, especially in antigravity muscles, namely mean change +/- standard deviation of descending part of trapezius (18.2% +/- 37.5%), anterior part of deltoid (37.7% +/- 16.7%), posterior part of deltoid (32.0% +/- 13.9%), and long head biceps (49.6% +/- 20.0%). Clinical implications for the use of gravity compensation in rehabilitation (during activities of daily living or exercise therapy) should be further investigated with a larger population. PMID:21110258

  19. Active micromachines: Microfluidics powered by mesoscale turbulence

    PubMed Central

    Thampi, Sumesh P.; Doostmohammadi, Amin; Shendruk, Tyler N.; Golestanian, Ramin; Yeomans, Julia M.

    2016-01-01

    Dense active matter, from bacterial suspensions and microtubule bundles driven by motor proteins to cellular monolayers and synthetic Janus particles, is characterized by mesoscale turbulence, which is the emergence of chaotic flow structures. By immersing an ordered array of symmetric rotors in an active fluid, we introduce a microfluidic system that exploits spontaneous symmetry breaking in mesoscale turbulence to generate work. The lattice of rotors self-organizes into a spin state where neighboring discs continuously rotate in permanent alternating directions due to combined hydrodynamic and elastic effects. Our virtual prototype demonstrates a new research direction for the design of micromachines powered by the nematohydrodynamic properties of active turbulence. PMID:27419229

  20. Active micromachines: Microfluidics powered by mesoscale turbulence.

    PubMed

    Thampi, Sumesh P; Doostmohammadi, Amin; Shendruk, Tyler N; Golestanian, Ramin; Yeomans, Julia M

    2016-07-01

    Dense active matter, from bacterial suspensions and microtubule bundles driven by motor proteins to cellular monolayers and synthetic Janus particles, is characterized by mesoscale turbulence, which is the emergence of chaotic flow structures. By immersing an ordered array of symmetric rotors in an active fluid, we introduce a microfluidic system that exploits spontaneous symmetry breaking in mesoscale turbulence to generate work. The lattice of rotors self-organizes into a spin state where neighboring discs continuously rotate in permanent alternating directions due to combined hydrodynamic and elastic effects. Our virtual prototype demonstrates a new research direction for the design of micromachines powered by the nematohydrodynamic properties of active turbulence. PMID:27419229

  1. Development of magnetically preloaded air bearings for a linear slide: active compensation of three degrees of freedom motion errors.

    PubMed

    Ro, Seung-Kook; Kim, Soohyun; Kwak, Yoonkeun; Park, Chun-Hong

    2008-03-01

    This article describes a linear air-bearing stage that uses active control to compensate for its motion errors. The active control is based on preloads generated by magnetic actuators, which were designed to generate nominal preloads for the air bearings using permanent magnets to maintain the desired stiffness while changing the air-bearing clearance by varying the magnetic flux generated by the current in electromagnetic coils. A single-axis linear stage with a linear motor and 240 mm of travel range was built to verify this design concept and used to test its performance. The motion of the table in three directions was controlled with four magnetic actuators driven by current amplifiers and a DSP (Digital Signal Processor)-based digital controller. The motion errors were measured using a laser interferometer combined with a two-probe method, and had 0.085 microm of repeatability for the straightness error. As a result of feed-forward active compensation, the errors were reduced from 1.09 to 0.11 microm for the vertical motion, from 9.42 to 0.18 arcsec for the pitch motion, and from 2.42 to 0.18 arcsec for the roll motion. PMID:18377049

  2. Optical Modeling Activities for NASA's James Webb Space Telescope (JWST). 3; Wavefront Aberrations due to Alignment and Figure Compensation

    NASA Technical Reports Server (NTRS)

    Howard, Joseph

    2007-01-01

    This is part three of a series describing the ongoing optical modeling activities for James Webb Space Telescope (JWST). The first two discussed modeling JWST on-orbit performance using wavefront sensitivities to predict line of sight motion induced blur, and stability during thermal transients. The work here investigates the aberrations resulting from alignment and figure compensation of the controllable degrees of freedom (primary and secondary mirrors), which may be encountered during ground alignment and on-orbit commissioning of the observatory. The optical design of the telescope is a three-mirror anastigmat, with an active fold mirror at the exit pupil for fine guiding. The primary mirror is over 6.5 meters in diameter, and is composed of 18 hexagonal segments that can individually positioned on hexapods, as well as compensated for radius of curvature. This effectively gives both alignment and figure control of the primary mirror. The secondary mirror can be moved in rigid body only, giving alignment control of the telescope. The tertiary mirror is fixed, however, as well as the location of the science instrumentation. Simulations are performed of various combinations of active alignment corrections of component figure errors, and of primary mirror figure corrections of alignment errors. Single field point and moderate field knowledge is assumed in the corrections. Aberrations over the field are reported for the varying cases, and examples presented.

  3. Development of magnetically preloaded air bearings for a linear slide: Active compensation of three degrees of freedom motion errors

    NASA Astrophysics Data System (ADS)

    Ro, Seung-Kook; Kim, Soohyun; Kwak, Yoonkeun; Park, Chun-Hong

    2008-03-01

    This article describes a linear air-bearing stage that uses active control to compensate for its motion errors. The active control is based on preloads generated by magnetic actuators, which were designed to generate nominal preloads for the air bearings using permanent magnets to maintain the desired stiffness while changing the air-bearing clearance by varying the magnetic flux generated by the current in electromagnetic coils. A single-axis linear stage with a linear motor and 240mm of travel range was built to verify this design concept and used to test its performance. The motion of the table in three directions was controlled with four magnetic actuators driven by current amplifiers and a DSP (Digital Signal Processor)-based digital controller. The motion errors were measured using a laser interferometer combined with a two-probe method, and had 0.085μm of repeatability for the straightness error. As a result of feed-forward active compensation, the errors were reduced from 1.09to0.11μm for the vertical motion, from 9.42to0.18arcsec for the pitch motion, and from 2.42to0.18arcsec for the roll motion.

  4. Space active optics: in situ compensation of lightweight primary mirrors' deformations

    NASA Astrophysics Data System (ADS)

    Laslandes, M.; Ferrari, M.; Hugot, E.; Lemaitre, G.

    2010-12-01

    The need for both high quality images and light structures is a constant concern in the conception of space telescopes. The goal here is to determine how an active optics system could be embarked on a satellite in order to correct the wave front deformations of the optical train. The optical aberrations appearing in a space environment are due to mirrors' deformations, with three main origins: the thermal variations, the weightlessness conditions and the use of large weightlighted primary mirrors. We are developing a model of deformable mirror as minimalist as possible, especially in term of number of actuators, which is able to correct the first Zernike polynomials in a specified range of amplitude and precision. Flight constraints as weight, volume and power consumption are considered. Firstly, such a system is designed according to the equations from the elasticity theory: we determine the geometrical and mechanical characteristics of the mirror, the location of the forces to be applied and the way to apply them. Then the concept is validated with a Finite Element Analysis, allowing to optimize the system by taking into account parameters absent from the theory. At the end, the mirror will be realized and characterized in a representative optical configuration.

  5. Compensation Chemistry

    ERIC Educational Resources Information Center

    Roady, Celia

    2008-01-01

    Congress, the news media, and the Internal Revenue Service (IRS) continue to cast a wary eye on the compensation of nonprofit leaders. Hence, any college or university board that falls short of IRS expectations in its procedures for setting the president's compensation is putting the president, other senior officials, and board members at…

  6. Optical modeling activities for NASA's James Webb Space Telescope (JWST): III. Wavefront aberrations due to alignment and figure compensation

    NASA Astrophysics Data System (ADS)

    Howard, Joseph M.

    2007-09-01

    This paper is part three of a series describing the ongoing optical modeling activities for the James Webb Space Telescope (JWST). The first two papers discussed modeling JWST on-orbit performance using wavefront sensitivities to predict line of sight motion induced blur, and stability during thermal transients [1-2]. The work here investigates the aberrations resulting from alignment and figure compensation of the controllable degrees of freedom (i.e. the primary and secondary mirrors), which may be encountered during ground alignment and on-orbit commissioning of the observatory. The optical design of the telescope is a three-mirror anastigmat, with an active fold mirror at the exit pupil for fine guiding. The primary mirror is over 6.5 meters in diameter, and is composed of 18 hexagonal segments that can individually positioned on hexapods, as well as compensated for radius of curvature. This architecture effectively gives both alignment and figure control of the primary mirror. The secondary mirror can be moved in rigid body only, and the tertiary mirror is fixed. Simulations are performed of various combinations of alignment and figure errors corrected by the primary and secondary mirrors. Single field point knowledge is assumed in the corrections, and aberrations over the field are reported for the varying cases.

  7. Applications of electron lenses: scraping of high-power beams, beam-beam compensation, and nonlinear optics

    SciTech Connect

    Stancari, Giulio

    2014-09-11

    Electron lenses are pulsed, magnetically confined electron beams whose current-density profile is shaped to obtain the desired effect on the circulating beam. Electron lenses were used in the Fermilab Tevatron collider for bunch-by-bunch compensation of long-range beam-beam tune shifts, for removal of uncaptured particles in the abort gap, for preliminary experiments on head-on beam-beam compensation, and for the demonstration of halo scraping with hollow electron beams. Electron lenses for beam-beam compensation are being commissioned in the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL). Hollow electron beam collimation and halo control were studied as an option to complement the collimation system for the upgrades of the Large Hadron Collider (LHC) at CERN; a conceptual design was recently completed. Because of their electric charge and the absence of materials close to the proton beam, electron lenses may also provide an alternative to wires for long-range beam-beam compensation in LHC luminosity upgrade scenarios with small crossing angles. At Fermilab, we are planning to install an electron lens in the Integrable Optics Test Accelerator (IOTA, a 40-m ring for 150-MeV electrons) as one of the proof-of-principle implementations of nonlinear integrable optics to achieve large tune spreads and more stable beams without loss of dynamic aperture.

  8. Monitoring Biological Activity at Geothermal Power Plants

    SciTech Connect

    Peter Pryfogle

    2005-09-01

    The economic impact of microbial growth in geothermal power plants has been estimated to be as high as $500,000 annually for a 100 MWe plant. Many methods are available to monitor biological activity at these facilities; however, very few plants have any on-line monitoring program in place. Metal coupon, selective culturing (MPN), total organic carbon (TOC), adenosine triphosphate (ATP), respirometry, phospholipid fatty acid (PLFA), and denaturing gradient gel electrophoresis (DGGE) characterizations have been conducted using water samples collected from geothermal plants located in California and Utah. In addition, the on-line performance of a commercial electrochemical monitor, the BIoGEORGE?, has been evaluated during extended deployments at geothermal facilities. This report provides a review of these techniques, presents data on their application from laboratory and field studies, and discusses their value in characterizing and monitoring biological activities at geothermal power plants.

  9. Statistical Performances of Resistive Active Power Splitter

    NASA Astrophysics Data System (ADS)

    Lalléchère, Sébastien; Ravelo, Blaise; Thakur, Atul

    2016-03-01

    In this paper, the synthesis and sensitivity analysis of an active power splitter (PWS) is proposed. It is based on the active cell composed of a Field Effect Transistor in cascade with shunted resistor at the input and the output (resistive amplifier topology). The PWS uncertainty versus resistance tolerances is suggested by using stochastic method. Furthermore, with the proposed topology, we can control easily the device gain while varying a resistance. This provides useful tool to analyse the statistical sensitivity of the system in uncertain environment.

  10. Temperature compensated silicon resonators for space applications

    NASA Astrophysics Data System (ADS)

    Rais-Zadeh, Mina; Thakar, Vikram A.; Wu, Zhengzheng; Peczalski, Adam

    2013-03-01

    This paper presents piezoelectric transduction and frequency trimming of silicon-based resonators with a center frequency in the low megahertz regime. The temperature coefficient of frequency (TCF) of the resonators is reduced using both passive and active compensation schemes. Specifically, a novel technique utilizing oxide-refilled trenches is implemented to achieve efficient temperature compensation while maintaining compatibility with wet release processes. Using this method, we demonstrate high-Q resonators having a first-order TCF as low as 3 ppm/°C and a turnover temperature of around 90 °C, ideally suited for use in ovenized platforms. Using active tuning, the temperature sensitivity of the resonator is further compensated around the turnover temperature, demonstrating frequency instability of less than 400 ppb. Such devices are ideally suited as timing units in space applications where size, power consumption, and temperature stability are of critical importance.

  11. Design of an input filter for power factor correction (PFC) AC to DC converters employing an active ripple cancellation

    SciTech Connect

    Lee, D.Y.; Cho, B.H.

    1996-12-31

    An active input filter for power factor correction (PFC) circuit employing ripple current cancellation is proposed to reduce the filter`s size and cost.Switching ripple current can be filtered by an active circuit from the line current. A single stage passive filter with the active filter compensation circuit, a high filter can be synthesized to meet the electromagnetic interference (EMI) and power factor requirements. Analysis of the active filter and design procedure are detailed. Simulation result is presented to verify the high order filter characteristics of proposed scheme.

  12. Healthy eating at school to compensate for the activity-related obesigenic lifestyle in children and adolescents: the Quebec experience.

    PubMed

    Tremblay, Angelo; Arguin, Hélène

    2011-03-01

    In this article, we describe the Quebec experience about the determinants of childhood obesity and the search for solutions, which are well adapted to the constraints of the current lifestyle. As expected, it is likely that a decrease in physical fitness and its related sedentariness as well as suboptimal food habits have contributed to the increase in overweight prevalence that was observed between 1980 and 2000. Our research experience suggests that other less suspected activity related factors have also played an important role in the occurrence of the obesity epidemic. This is particularly the case for short sleeping and demanding mental work, which are features of our modern lifestyle. Because there is no foreseeable prospect for a change in sleep and mental work habits, we argue that compensations in other factors may be necessary to prevent weight gain in this new context. We thus developed a concept of food design aiming at the maximization of the satiating properties of a food or a meal course. In this context, we were successful in the design of healthy lunch bags for students of a school located in a low socioeconomic area. Indeed, for a majority of menus, an optimal compromise seemed to be reached between nutrient composition, satiating potential, palatability, and financial accessibility. In summary, the Quebec experience reveals that childhood obesity is a complex problem that partly results from unsuspected environmental factors that deserve creative solutions to at least partly compensate for their effect. PMID:22332048

  13. Cobalt(III) Protoporphyrin Activates the DGCR8 Protein and Can Compensate microRNA Processing Deficiency.

    PubMed

    Barr, Ian; Weitz, Sara H; Atkin, Talia; Hsu, PeiKen; Karayiorgou, Maria; Gogos, Joseph A; Weiss, Shimon; Guo, Feng

    2015-06-18

    Processing of microRNA primary transcripts (pri-miRNAs) is highly regulated and defects in the processing machinery play a key role in many human diseases. In 22q11.2 deletion syndrome (22q11.2DS), heterozygous deletion of DiGeorge critical region gene 8 (DGCR8) causes a processing deficiency, which contributes to abnormal brain development. The DGCR8 protein is the RNA-binding partner of Drosha RNase, both essential for processing canonical pri-miRNAs. To identify an agent that can compensate reduced DGCR8 expression, we screened for metalloporphyrins that can mimic the natural DGCR8 heme cofactor. We found that Co(III) protoporphyrin IX (PPIX) stably binds DGCR8 and activates it for pri-miRNA processing in vitro and in HeLa cells. Importantly, treating cultured Dgcr8(+/-) mouse neurons with Co(III)PPIX can compensate the pri-miRNA processing defects. Co(III)PPIX is effective at concentrations as low as 0.2 μM and is not degraded by heme degradation enzymes, making it useful as a research tool and a potential therapeutic. PMID:26091172

  14. Terbium gallium garnet ceramic-based Faraday isolator with compensation of thermally induced depolarization for high-energy pulsed lasers with kilowatt average power

    SciTech Connect

    Yasuhara, Ryo; Snetkov, Ilya; Starobor, Alexey; Palashov, Oleg

    2014-12-15

    A scalable aperture Faraday isolator for high-energy pulsed lasers with kW-level average power was demonstrated using terbium gallium garnet ceramics with water cooling and compensation of thermally induced depolarization in a magnetic field. An isolation ratio of 35 dB (depolarization ratio γ of 3.4 × 10{sup −4}) was experimentally observed at a maximum laser power of 740 W. By using this result, we estimated that this isolator maintains an isolation ratio of 30 dB for laser powers of up to 2.7 kW. Our results provide the solution for achieving optical isolation in high-energy (100 J to kJ) laser systems with a repetition rate greater than 10 Hz.

  15. The Impact of Model Uncertainty on Spatial Compensation in Active Structural Acoustic Control

    NASA Technical Reports Server (NTRS)

    Cabell, Randolph H.; Gibbs, Gary P.; Sprofera, Joseph D.; Clark, Robert L.

    2004-01-01

    Turbulent boundary layer (TBL) noise is considered a primary factor in the interior noise experienced by passengers aboard commercial airliners. There have been numerous investigations of interior noise control devoted to aircraft panels; however, practical realization is a challenge since the physical boundary conditions are uncertain at best. In most prior studies, pinned or clamped boundary conditions have been assumed; however, realistic panels likely display a range of varying boundary conditions between these two limits. Uncertainty in boundary conditions is a challenge for control system designers, both in terms of the compensator implemented and the location of actuators and sensors required to achieve the desired control. The impact of model uncertainties, uncertain boundary conditions in particular, on the selection of actuator and sensor locations for structural acoustic control are considered herein. Results from this research effort indicate that it is possible to optimize the design of actuator and sensor location and aperture, which minimizes the impact of boundary conditions on the desired structural acoustic control.

  16. A fast time domain digital simulation technique for power converters - Application to a buck converter with feedforward compensation

    NASA Technical Reports Server (NTRS)

    Kelkar, S. S.; Lee, F. C.

    1984-01-01

    Small signal analysis was performed earlier to demonstrate the marked improvement of dynamic properties and stability margins of a switching regulator employing a novel feedforward input filter compensation scheme. A large signal nonlinear recurrent time domain model is presented for the converter to analyse the transient response due to a step input change with and without the presence of the proposed feedforward loop. The results are verified with experimental data.

  17. A Method for Compensating Customer Voltage Drops due to Nighttime Simultaneous Charging of EVs Utilizing Reactive Power Injection from Battery Chargers

    NASA Astrophysics Data System (ADS)

    Noda, Taku; Kabasawa, Yuichiro; Fukushima, Kentaro; Nemoto, Koshichi; Uemura, Satoshi

    When we consider the global warming, the reduction of CO2 emission is one of the most important problems which require urgent solutions. One option is to integrate low-CO2-emission generators to the grid as much as possible. Another option is to replace inefficient vehicles based on internal-combustion engines with electric ones (EVs). Due to the latter, we can easily estimate that most consumers will charge EVs' batteries at nighttime. Thus, excessive voltage drops due to the nighttime simultaneous charging are supposed to be a possible future problem. This paper proposes a method for compensating the voltage drops by injecting reactive power from EV battery chargers.

  18. Ratchet transport powered by chiral active particles

    PubMed Central

    Ai, Bao-quan

    2016-01-01

    We numerically investigate the ratchet transport of mixtures of active and passive particles in a transversal asymmetric channel. A big passive particle is immersed in a ‘sea’ of active particles. Due to the chirality of active particles, the longitudinal directed transport is induced by the transversal asymmetry. For the active particles, the chirality completely determines the direction of the ratchet transport, the counterclockwise and clockwise particles move to the opposite directions and can be separated. However, for the passive particle, the transport behavior becomes complicated, the direction is determined by competitions among the chirality, the self-propulsion speed, and the packing fraction. Interestingly, within certain parameters, the passive particle moves to the left, while active particles move to the right. In addition, there exist optimal parameters (the chirality, the height of the barrier, the self-propulsion speed and the packing fraction) at which the rectified efficiency takes its maximal value. Our findings could be used for the experimental pursuit of the ratchet transport powered by chiral active particles. PMID:26795952

  19. Ratchet transport powered by chiral active particles

    NASA Astrophysics Data System (ADS)

    Ai, Bao-Quan

    2016-01-01

    We numerically investigate the ratchet transport of mixtures of active and passive particles in a transversal asymmetric channel. A big passive particle is immersed in a ‘sea’ of active particles. Due to the chirality of active particles, the longitudinal directed transport is induced by the transversal asymmetry. For the active particles, the chirality completely determines the direction of the ratchet transport, the counterclockwise and clockwise particles move to the opposite directions and can be separated. However, for the passive particle, the transport behavior becomes complicated, the direction is determined by competitions among the chirality, the self-propulsion speed, and the packing fraction. Interestingly, within certain parameters, the passive particle moves to the left, while active particles move to the right. In addition, there exist optimal parameters (the chirality, the height of the barrier, the self-propulsion speed and the packing fraction) at which the rectified efficiency takes its maximal value. Our findings could be used for the experimental pursuit of the ratchet transport powered by chiral active particles.

  20. Ratchet transport powered by chiral active particles.

    PubMed

    Ai, Bao-quan

    2016-01-01

    We numerically investigate the ratchet transport of mixtures of active and passive particles in a transversal asymmetric channel. A big passive particle is immersed in a 'sea' of active particles. Due to the chirality of active particles, the longitudinal directed transport is induced by the transversal asymmetry. For the active particles, the chirality completely determines the direction of the ratchet transport, the counterclockwise and clockwise particles move to the opposite directions and can be separated. However, for the passive particle, the transport behavior becomes complicated, the direction is determined by competitions among the chirality, the self-propulsion speed, and the packing fraction. Interestingly, within certain parameters, the passive particle moves to the left, while active particles move to the right. In addition, there exist optimal parameters (the chirality, the height of the barrier, the self-propulsion speed and the packing fraction) at which the rectified efficiency takes its maximal value. Our findings could be used for the experimental pursuit of the ratchet transport powered by chiral active particles. PMID:26795952

  1. Energy and power limits for microbial activity

    NASA Astrophysics Data System (ADS)

    LaRowe, D.; Amend, J.

    2014-12-01

    The goal of this presentation is to describe a quantitative framework for determining how energy limits microbial activity, biomass and, ultimately, biogeochemical processes. Although this model can be applied to any environment, its utility is demonstrated in marine sediments, which are an attractive test habitat because they encompass a broad spectrum of energy levels, varying amounts of biomass and are ubiquitous. The potential number of active microbial cells in Arkonas Basin (Baltic Sea) sediments are estimated as a function of depth by quantifying the amount of energy that is available to them and the rate at which it is supplied: power. The amount of power supplied per cubic centimeter of sediment is determined by calculating the Gibbs energy of fermentation and sulfate reduction in combination with the rate of particulate organic carbon, POC, degradation. The Reactive Continuum Model (Boudreau and Ruddick, 1991), RCM, is used to determine the rate at which POC is made available for microbial consumption. The RCM represents POC as containing a range of different types of organic compounds whose ability to be consumed by microorganisms varies as a function of the age of the sediment and on the distribution of compound types that were initially deposited. The sediment age model and RCM parameters determined by (Mogollon et al., 2012) are used. The power available for fermentation and sulfate reduction coupled to H2 and acetate oxidation varies from 10-8 W cm-3 at the sediment water interface to between 10-11 - 10-12 W cm-3 at 3.5 meters below the seafloor, mbsf. Using values of maintenance powers for each of these catabolic activities taken from the literature, the total number of active cells in these sediments similarly decreases from just less than 108 cell cm-3 at the SWI to 4.6 x 104 cells cm-3 at 3.5 mbsf. The number of moles of POC decreases from 2.6 x 10-5 to 9.5 x 10-6, also becoming more recalcitrant with depth. Boudreau, B. P. and Ruddick, B. R

  2. Alumina Encapsulated Strain Gage Not Mechanically Attached To The Substrate, Used to Temperature Compensate an Active High Temperature Gage In A Half-Bridge Configuration

    NASA Technical Reports Server (NTRS)

    Piazza, Anthony (Inventor)

    2001-01-01

    A temperature compensation element for a high-temperature strain gage and the method of fabricating the same. Preferably, the element is a "dummy" strain gage not mechanically attached to the substrate. The element is encapsulated in an insulative material and used to compensate an active high-temperature strain gage and wired in a half-bridge configuration. The temperature compensation element and high-temperature strain gage are fabricated using the method of the present invention. This method includes temporarily adhering the element to a heat sink, encapsulated in an insulative material and then removed from the heat sink. Next, the element is either stacked or placed near the active gage. Ideally, the element and the active gage have substantially similar heat transfer and electrical properties.

  3. The American compensation phenomenon.

    PubMed

    Bale, A

    1990-01-01

    In this article, the author defines the occupational safety and health domain, characterizes the distinct compensation phenomenon in the United States, and briefly reviews important developments in the last decade involving Karen Silkwood, intentional torts, and asbestos litigation. He examines the class conflict over the value and meaning of work-related injuries and illnesses involved in the practical activity of making claims and turning them into money through compensation inquiries. Juries, attributions of fault, and medicolegal discourse play key roles in the compensation phenomenon. This article demonstrates the extensive, probing inquiry through workers' bodies constituted by the American compensation phenomenon into the moral basis of elements of the system of production. PMID:2139638

  4. Willingness to Take PrEP and Potential for Risk Compensation Among Highly Sexually Active Gay and Bisexual Men.

    PubMed

    Grov, Christian; Whitfield, Thomas H F; Rendina, H Jonathon; Ventuneac, Ana; Parsons, Jeffrey T

    2015-12-01

    Once-daily Truvada (Emtricitabine/Tenofovir) as a method of pre-exposure prophylaxis (PrEP) is one of the most promising biomedical interventions to eliminate new HIV infections; however, uptake among gay, bisexual, and other men who have sex with men has been slow amidst growing concern in popular/social media that PrEP use will result in reduced condom use (i.e., risk compensation). We investigated demographic, behavioral, and psychosocial differences in willingness to use PrEP as well as the perceived impact of PrEP on participants' condom use in a sample of 206 highly sexually active HIV-negative gay and bisexual men. Nearly half (46.1 %) said they would be willing to take PrEP if it were provided at no cost. Although men willing to take PrEP (vs. others) reported similar numbers of recent casual male partners (<6 weeks), they had higher odds of recent receptive condomless anal sex (CAS)-i.e., those already at high risk of contracting HIV were more willing to take PrEP. Neither age, race/ethnicity, nor income were associated with willingness to take PrEP, suggesting equal acceptability among subpopulations that are experiencing disparities in HIV incidence. There was limited evidence to suggest men would risk compensate. Only 10 % of men who had not engaged in recent CAS felt that PrEP would result in them starting to have CAS. Men who had not tested for HIV recently were also significantly more likely than others to indicate willingness to take PrEP. Offering PrEP to men who test infrequently may serve to engage them more in routine HIV/STI testing and create a continued dialogue around sexual health between patient and provider in order to prevent HIV infection. PMID:25735243

  5. Wind Powering America FY07 Activities Summary

    SciTech Connect

    Not Available

    2008-02-01

    The Wind Powering America FY07 Activities Summary reflects the accomplishments of our state wind working groups, our programs at the National Renewable Energy Laboratory, and our partner organizations. The national WPA team remains a leading force for moving wind energy forward in the United States. WPA continues to work with its national, regional, and state partners to communicate the opportunities and benefits of wind energy to a diverse set of stakeholders. WPA now has 30 state wind working groups (welcoming Georgia and Wisconsin in 2007) that form strategic alliances to communicate wind's benefits to the state stakeholders. More than 140 members of national and state public and private sector organizations from 39 U.S. states and Canada attended the 6th Annual WPA All-States Summit in Los Angeles in June. WPA's emphasis remains on the rural agricultural sector, which stands to reap the significant economic development benefits of wind energy development. Additionally, WPA continues its program of outreach, education, and technical assistance to Native American communities, public power entities, and regulatory and legislative bodies.

  6. Wind Powering America FY06 Activities Summary

    SciTech Connect

    Not Available

    2007-02-01

    The Wind Powering America FY06 Activities Summary reflects the accomplishments of our state wind working groups, our programs at the National Renewable Energy Laboratory, and our partner organizations. The national WPA team remains a leading force for moving wind energy forward in the United States. WPA continues to work with its national, regional, and state partners to communicate the opportunities and benefits of wind energy to a diverse set of stakeholders. WPA now has 29 state wind working groups (welcoming New Jersey, Indiana, Illinois, and Missouri in 2006) that form strategic alliances to communicate wind's benefits to the state stakeholders. More than 120 members of national and state public and private sector organizations from 34 states attended the 5th Annual WPA All-States Summit in Pittsburgh in June.

  7. Optically powered active sensing system for Internet Of Things

    NASA Astrophysics Data System (ADS)

    Gao, Chen; Wang, Jin; Yin, Long; Yang, Jing; Jiang, Jian; Wan, Hongdan

    2014-10-01

    Internet Of Things (IOT) drives a significant increase in the extent and type of sensing technology and equipment. Sensors, instrumentation, control electronics, data logging and transmission units comprising such sensing systems will all require to be powered. Conventionally, electrical powering is supplied by batteries or/and electric power cables. The power supply by batteries usually has a limited lifetime, while the electric power cables are susceptible to electromagnetic interference. In fact, the electromagnetic interference is the key issue limiting the power supply in the strong electromagnetic radiation area and other extreme environments. The novel alternative method of power supply is power over fiber (PoF) technique. As fibers are used as power supply lines instead, the delivery of the power is inherently immune to electromagnetic radiation, and avoids cumbersome shielding of power lines. Such a safer power supply mode would be a promising candidate for applications in IOT. In this work, we built up optically powered active sensing system, supplying uninterrupted power for the remote active sensors and communication modules. Also, we proposed a novel maximum power point tracking technique for photovoltaic power convertors. In our system, the actual output efficiency greater than 40% within 1W laser power. After 1km fiber transmission and opto-electric power conversion, a stable electric power of 210mW was obtained, which is sufficient for operating an active sensing system.

  8. The aspartyl protease DDI2 activates Nrf1 to compensate for proteasome dysfunction

    PubMed Central

    Koizumi, Shun; Irie, Taro; Hirayama, Shoshiro; Sakurai, Yasuyuki; Yashiroda, Hideki; Naguro, Isao; Ichijo, Hidenori; Hamazaki, Jun; Murata, Shigeo

    2016-01-01

    In response to proteasome dysfunction, mammalian cells upregulate proteasome gene expression by activating Nrf1. Nrf1 is an endoplasmic reticulum-resident transcription factor that is continually retrotranslocated and degraded by the proteasome. Upon proteasome inhibition, Nrf1 escapes degradation and is cleaved to become active. However, the processing enzyme for Nrf1 remains obscure. Here we show that the aspartyl protease DNA-damage inducible 1 homolog 2 (DDI2) is required to cleave and activate Nrf1. Deletion of DDI2 reduced the cleaved form of Nrf1 and increased the full-length cytosolic form of Nrf1, resulting in poor upregulation of proteasomes in response to proteasome inhibition. These defects were restored by adding back wild-type DDI2 but not protease-defective DDI2. Our results provide a clue for blocking compensatory proteasome synthesis to improve cancer therapies targeting proteasomes. DOI: http://dx.doi.org/10.7554/eLife.18357.001 PMID:27528193

  9. Driving Method for Compensating Reliability Problem of Hydrogenated Amorphous Silicon Thin Film Transistors and Image Sticking Phenomenon in Active Matrix Organic Light-Emitting Diode Displays

    NASA Astrophysics Data System (ADS)

    Shin, Min-Seok; Jo, Yun-Rae; Kwon, Oh-Kyong

    2011-03-01

    In this paper, we propose a driving method for compensating the electrical instability of hydrogenated amorphous silicon (a-Si:H) thin film transistors (TFTs) and the luminance degradation of organic light-emitting diode (OLED) devices for large active matrix OLED (AMOLED) displays. The proposed driving method senses the electrical characteristics of a-Si:H TFTs and OLEDs using current integrators and compensates them by an external compensation method. Threshold voltage shift is controlled a using negative bias voltage. After applying the proposed driving method, the measured error of the maximum emission current ranges from -1.23 to +1.59 least significant bit (LSB) of a 10-bit gray scale under the threshold voltage shift ranging from -0.16 to 0.17 V.

  10. Economics of static VAR compensation

    SciTech Connect

    Alvarado, F.L.; DeMarco, C.; Jung, T.H. . Dept. of Electrical and Computer Engineering)

    1992-09-01

    This project was initiated in anticipation of widened use of static VAR (volt-ampere-reactive) compensation on US bulk-power transmission systems to increase levels of secure power transfer. Project objectives were to deten-nine power system cost savings and reliability benefits resulting from such use. System operating cost and stability probabilities were compared with and without static VAR compensation, applying simulation techniques. For the particular system model studied, there was a 21.4 percent reduction in operating costs taking into account losses added by the static VAR compensator. A procedure was developed to compare instability probabilities for various loadings and static VAR compensator sizes on a power system. For the particular system model studied, the static VAR compensator provided a significant increase in stability but over a narrow range of loading. Static VAR compensation is one of a number of promising FACTS (Flexible AC Transmission System) technologies for handling the demands of increased power transfers on power systems where transmission lines cannot be built or as a short-term altemative to building additional lines.

  11. Compensating for the absence of selenocysteine in high-molecular weight thioredoxin reductases: the electrophilic activation hypothesis.

    PubMed

    Lothrop, Adam P; Snider, Gregg W; Flemer, Stevenson; Ruggles, Erik L; Davidson, Ronald S; Lamb, Audrey L; Hondal, Robert J

    2014-02-01

    Mammalian thioredoxin reductase (TR) is a pyridine disulfide oxidoreductase that uses the rare amino acid selenocysteine (Sec) in place of the more commonly used amino acid cysteine (Cys). Selenium is a Janus-faced element because it is both highly nucleophilic and highly electrophilic. Cys orthologs of Sec-containing enzymes may compensate for the absence of a Sec residue by making the active site Cys residue more (i) nucleophilic, (ii) electrophilic, or (iii) reactive by increasing both S-nucleophilicity and S-electrophilicity. It has already been shown that the Cys ortholog TR from Drosophila melanogaster (DmTR) has increased S-nucleophilicity [Gromer, S., Johansson, L., Bauer, H., Arscott, L. D., Rauch, S., Ballou, D. P., Williams, C. H., Jr., Schrimer, R. H., and Arnér, E. S (2003) Active sites of thioredoxin reductases: Why selenoproteins? Proc. Natl. Acad. Sci. U.S.A. 100, 12618-12623]. Here we present evidence that DmTR also enhances the electrophilicity of Cys490 through the use of an "electrophilic activation" mechanism. This mechanism is proposed to work by polarizing the disulfide bond that occurs between Cys489 and Cys490 in the C-terminal redox center by the placement of a positive charge near Cys489. This polarization renders the sulfur atom of Cys490 electron deficient and enhances the rate of thiol/disulfide exchange that occurs between the N- and C-terminal redox centers. Our hypothesis was developed by using a strategy of homocysteine (hCys) for Cys substitution in the Cys-Cys redox dyad of DmTR to differentiate the function of each Cys residue. The results show that hCys could substitute for Cys490 with little loss of thioredoxin reductase activity, but that substitution of hCys for Cys489 resulted in a 238-fold reduction in activity. We hypothesize that replacement of Cys489 with hCys destroys an interaction between the sulfur atom of Cys489 and His464 crucial for the proposed electrophilic activation mechanism. This electrophilic activation

  12. Direct charge radioisotope activation and power generation

    DOEpatents

    Lal, Amit; Li, Hui; Blanchard, James P.; Henderson, Douglass L.

    2002-01-01

    An activator has a base on which is mounted an elastically deformable micromechanical element that has a section that is free to be displaced toward the base. An absorber of radioactively emitted particles is formed on the base or the displaceable section of the deformable element and a source is formed on the other of the displaceable section or the base facing the absorber across a small gap. The radioactive source emits charged particles such as electrons, resulting in a buildup of charge on the absorber, drawing the absorber and source together and storing mechanical energy as the deformable element is bent. When the force between the absorber and the source is sufficient to bring the absorber into effective electrical contact with the source, discharge of the charge between the source and absorber allows the deformable element to spring back, releasing the mechanical energy stored in the element. An electrical generator such as a piezoelectric transducer may be secured to the deformable element to convert the released mechanical energy to electrical energy that can be used to provide power to electronic circuits.

  13. Compensating for the Absence of Selenocysteine in High-Molecular Weight Thioredoxin Reductases: The Electrophilic Activation Hypothesis

    PubMed Central

    2015-01-01

    Mammalian thioredoxin reductase (TR) is a pyridine disulfide oxidoreductase that uses the rare amino acid selenocysteine (Sec) in place of the more commonly used amino acid cysteine (Cys). Selenium is a Janus-faced element because it is both highly nucleophilic and highly electrophilic. Cys orthologs of Sec-containing enzymes may compensate for the absence of a Sec residue by making the active site Cys residue more (i) nucleophilic, (ii) electrophilic, or (iii) reactive by increasing both S-nucleophilicity and S-electrophilicity. It has already been shown that the Cys ortholog TR from Drosophila melanogaster (DmTR) has increased S-nucleophilicity [Gromer, S., Johansson, L., Bauer, H., Arscott, L. D., Rauch, S., Ballou, D. P., Williams, C. H., Jr., Schrimer, R. H., and Arnér, E. S (2003) Active sites of thioredoxin reductases: Why selenoproteins? Proc. Natl. Acad. Sci. U.S.A. 100, 12618–12623]. Here we present evidence that DmTR also enhances the electrophilicity of Cys490 through the use of an “electrophilic activation” mechanism. This mechanism is proposed to work by polarizing the disulfide bond that occurs between Cys489 and Cys490 in the C-terminal redox center by the placement of a positive charge near Cys489. This polarization renders the sulfur atom of Cys490 electron deficient and enhances the rate of thiol/disulfide exchange that occurs between the N- and C-terminal redox centers. Our hypothesis was developed by using a strategy of homocysteine (hCys) for Cys substitution in the Cys-Cys redox dyad of DmTR to differentiate the function of each Cys residue. The results show that hCys could substitute for Cys490 with little loss of thioredoxin reductase activity, but that substitution of hCys for Cys489 resulted in a 238-fold reduction in activity. We hypothesize that replacement of Cys489 with hCys destroys an interaction between the sulfur atom of Cys489 and His464 crucial for the proposed electrophilic activation mechanism. This electrophilic

  14. Intracellular shunting of O2− contributes to charge compensation and preservation of neutrophil respiratory burst in the absence of voltage-gated proton channel activity

    PubMed Central

    Decleva, Eva; Menegazzi, Renzo; Fasolo, Alba; Defendi, Federica; Sebastianutto, Michele; Dri, Pietro

    2013-01-01

    Proton efflux via voltage-gated proton channels (Hv1) is considered to mediate the charge compensation necessary to preserve NADPH oxidase activity during the respiratory burst. Using the Hv1 inhibitor Zn2+, we found that the PMA-induced respiratory burst of human neutrophils is inhibited when assessed as extracellular production of O2− and H2O2, in accordance with literature studies, but, surprisingly, unaffected when measured as oxygen consumption or total (extracellular plus intracellular) H2O2 production. Furthermore, we show that inhibiting Hv1 with Zn2+ results in an increased production of intracellular ROS. Similar results, i.e. decreased extracellular and increased intracellular ROS production, were obtained using a human granulocyte-like cell line with severely impaired Hv1 expression. Acidic extracellular pH, which dampens proton efflux, also augmented intracellular production of H2O2. Zinc caused an increase in the rate but not in the extent of depolarization and cytosolic acidification indicating that mechanisms other than proton efflux take part in charge compensation. Our results suggest a hitherto unpredicted mechanism of charge compensation whereby, in the absence of proton efflux, part of O2− generated within gp91phox in the plasma membrane is shunted intracellularly down electrochemical gradient to dampen excessive depolarization. This would preserve NADPH oxidase activity under conditions such as the inflammatory exudate in which the acidic pH hinders charge compensation by proton efflux. PMID:23578765

  15. Adaptive compensation of lower order thermal aberrations in concave-convex power oscillators under variable pump conditions

    NASA Astrophysics Data System (ADS)

    Jackel, Steven M.; Moshe, Inon

    2000-09-01

    A Nd:Cr:GSGG concave-convex power oscillator was developed that utilized both an adaptive mirror comprised of spherical and cylindrical optical elements together with a Faraday rotator to dynamically eliminate lower order aberrations (thermal focusing, astigmatism, and bipolar focusing). An adaptively controlled collimating lens corrected for shifts in the mode-waist position. The addition of a polarizer and a reentrant mirror totally eliminated thermal birefringence losses. The techniques developed are attractive in any solid state laser that must work under changing pump power conditions.

  16. Agent-based power sharing scheme for active hybrid power sources

    NASA Astrophysics Data System (ADS)

    Jiang, Zhenhua

    The active hybridization technique provides an effective approach to combining the best properties of a heterogeneous set of power sources to achieve higher energy density, power density and fuel efficiency. Active hybrid power sources can be used to power hybrid electric vehicles with selected combinations of internal combustion engines, fuel cells, batteries, and/or supercapacitors. They can be deployed in all-electric ships to build a distributed electric power system. They can also be used in a bulk power system to construct an autonomous distributed energy system. An important aspect in designing an active hybrid power source is to find a suitable control strategy that can manage the active power sharing and take advantage of the inherent scalability and robustness benefits of the hybrid system. This paper presents an agent-based power sharing scheme for active hybrid power sources. To demonstrate the effectiveness of the proposed agent-based power sharing scheme, simulation studies are performed for a hybrid power source that can be used in a solar car as the main propulsion power module. Simulation results clearly indicate that the agent-based control framework is effective to coordinate the various energy sources and manage the power/voltage profiles.

  17. Cystometric parameters and the activity of signaling proteins in association with the compensation or decompensation of bladder function in an animal experimental model of partial bladder outlet obstruction.

    PubMed

    Choi, Bo-Hwa; Jin, Long-Hu; Kim, Khae-Hawn; Kang, Sung-An; Kang, Ju-Hee; Yoon, Sang-Min; Park, Chang-Shin; Lee, Tack

    2013-12-01

    We conducted this study to determine whether the degree of detrusor contractility is associated with the compensation or decompensation of bladder function depending on the residual volume (RV) during the first two weeks after the onset of partial bladder outlet obstruction (BOO). Moreover, we also examined whether the degree of the phosphorylation and expression of signaling proteins [AMP-activated kinase (AMPK), extracellular signal‑regulated protein kinases 1 and 2 (ERK1/2) and protein kinase C (PKC)] is associated with the prevalence of compensation or decompensation of bladder function. Twenty-seven female Sprague-Dawley (SD) rats were randomly assigned to either the sham-operated group (n=7) or the group with partial bladder outlet obstruction (BOO) (n=20). We then measured cystometric parameters from three reproducible micturition cycles and averaged the results for a comparison between the two groups. Based on a cut-off value of a mean RV% of 25%, we subdivided our experimental animals into two subgroups: the subgroup with bladder compensation (mean RV%, <25%) and the subgroup with bladder decompensation (mean RV%, >25%). Our results indicated that the degree of detrusor overactivity (DO) was associated with the compensation or decompensation of bladder function depending on the RV during the first two weeks after the onset of BOO in an animal experimental model of partial BOO. Moreover, we also demonstrate that AMPK and ERK1/2 are involved in the compensation or decompensation of bladder function. Furthermore, our results suggest that PKC is not involved in two-phase bladder contraction. Alterations in the activities of signaling proteins, such as AMPK and ERK1/2 may prove to be helpful in the treatment of patients with voiding difficulty. PMID:24085268

  18. Estimated times to exhaustion and power outputs at the gas exchange threshold, physical working capacity at the rating of perceived exertion threshold, and respiratory compensation point.

    PubMed

    Bergstrom, Haley C; Housh, Terry J; Zuniga, Jorge M; Camic, Clayton L; Traylor, Daniel A; Schmidt, Richard J; Johnson, Glen O

    2012-10-01

    The purposes of this study were to compare the power outputs and estimated times to exhaustion (T(lim)) at the gas exchange threshold (GET), physical working capacity at the rating of perceived exertion threshold (PWC(RPE)), and respiratory compensation point (RCP). Three male and 5 female subjects (mean ± SD: age, 22.4 ± 2.8 years) performed an incremental test to exhaustion on an electronically braked cycle ergometer to determine peak oxygen consumption rate, GET, and RCP. The PWC(RPE) was determined from ratings of perceived exertion data recorded during 3 continuous workbouts to exhaustion. The estimated T(lim) values for each subject at GET, PWC(RPE), and RCP were determined from power curve analyses (T(lim) = ax(b)). The results indicated that the PWC(RPE) (176 ± 55 W) was not significantly different from RCP (181 ± 54 W); however, GET (155 ± 42 W) was significantly less than PWC(RPE) and RCP. The estimated T(lim) for the GET (26.1 ± 9.8 min) was significantly greater than PWC(RPE) (14.6 ± 5.6 min) and RCP (11.2 ± 3.1 min). The PWC(RPE) occurred at a mean power output that was 13.5% greater than the GET and, therefore, it is likely that the perception of effort is not driven by the same mechanism that underlies the GET (i.e., lactate buffering). Furthermore, the PWC(RPE) and RCP were not significantly different and, therefore, these thresholds may be associated with the same mechanisms of fatigue, such as increased levels of interstitial and (or) arterial [K⁺]. PMID:22716291

  19. 12 CFR 7.2011 - Compensation plans.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Compensation plans. 7.2011 Section 7.2011 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY BANK ACTIVITIES AND OPERATIONS Corporate Practices § 7.2011 Compensation plans. Consistent with safe and sound banking practices and the compensation provisions of 12 CFR part 30,...

  20. Active Faults and Nuclear Power Plants

    NASA Astrophysics Data System (ADS)

    Chapman, Neil; Berryman, Kelvin; Villamor, Pilar; Epstein, Woody; Cluff, Lloyd; Kawamura, Hideki

    2014-01-01

    The destruction of the Fukushima Daiichi Nuclear Power Plant (NPP) following the March 2011 Tohoku earthquake and tsunami brought into sharp focus the susceptibility of NPPs to natural hazards. This is not a new issue—seismic hazard has affected the development of plants in the United States, and volcanic hazard was among the reasons for not commissioning the Bataan NPP in the Philippines [Connor et al., 2009].

  1. Sustainable Buildings. Using Active Solar Power

    SciTech Connect

    Sharp, M. Keith; Barnett, Russell

    2015-04-20

    The objective of this project is to promote awareness and knowledge of active solar energy technologies by installing and monitoring the following demonstration systems in Kentucky: 1) Pool heating system, Churchill Park School, 2) Water heating and daylighting systems, Middletown and Aiken Road Elementary Schools, 3) Photovoltaic street light comparison, Louisville Metro, 4) up to 25 domestic water heating systems across Kentucky. These tasks will be supported by outreach activities, including a solar energy installer training workshop and a Kentucky Solar Energy Conference.

  2. Human-robot interaction: kinematics and muscle activity inside a powered compliant knee exoskeleton.

    PubMed

    Knaepen, Kristel; Beyl, Pieter; Duerinck, Saartje; Hagman, Friso; Lefeber, Dirk; Meeusen, Romain

    2014-11-01

    Until today it is not entirely clear how humans interact with automated gait rehabilitation devices and how we can, based on that interaction, maximize the effectiveness of these exoskeletons. The goal of this study was to gain knowledge on the human-robot interaction, in terms of kinematics and muscle activity, between a healthy human motor system and a powered knee exoskeleton (i.e., KNEXO). Therefore, temporal and spatial gait parameters, human joint kinematics, exoskeleton kinetics and muscle activity during four different walking trials in 10 healthy male subjects were studied. Healthy subjects can walk with KNEXO in patient-in-charge mode with some slight constraints in kinematics and muscle activity primarily due to inertia of the device. Yet, during robot-in-charge walking the muscular constraints are reversed by adding positive power to the leg swing, compensating in part this inertia. Next to that, KNEXO accurately records and replays the right knee kinematics meaning that subject-specific trajectories can be implemented as a target trajectory during assisted walking. No significant differences in the human response to the interaction with KNEXO in low and high compliant assistance could be pointed out. This is in contradiction with our hypothesis that muscle activity would decrease with increasing assistance. It seems that the differences between the parameter settings of low and high compliant control might not be sufficient to observe clear effects in healthy subjects. Moreover, we should take into account that KNEXO is a unilateral, 1 degree-of-freedom device. PMID:24846650

  3. The central power source in active galaxies

    NASA Astrophysics Data System (ADS)

    Ptak, Roger; Stoner, Ronald

    Potential sources for the central power in AGN are examined. The continuum, emission line profiles, and time variability and broad emission line region for AGN are analyzed. The supermassive black hole hypothesis, the supermassive magnetized core model of Kundt (1978), and the model of Stoner and Ptak (1984) in which the supermassive stars maintain a kind of long-term quasi-stability, but accretion is balanced by mass loss and spherical bursts rather than in jets are considered. It is argued that the hypothesis that the supermassive blackholes are the central engines for AGN is based on theoretical principles; however, AGN emission line profiles and variability suggest a spherical geometry for the observed components of these engines. Also the supermassive black hole models do not account for all the AGN observations.

  4. Discussions and Comparisons between Comprehensive Harmonic Detection and Specific Harmonic Detection in a Shunt Active Filter for Installation on a Power Distribution System

    NASA Astrophysics Data System (ADS)

    Yamashita, Hiroshi; Pichai, Jintakosonwit; Fujita, Hideaki; Akagi, Hirofumi; Shinohara, Junya

    This paper deals with harmonic voltage detection methods for a shunt active filter intended for installation on a power distribution system. The active filter acts as a resistor to damp out harmonic propagation throughout the power distribution system. However, the active filter may fall into an unstable condition, because the control system forms a complex feedback loop including harmonic detection, current control, and system impedance. Stability and harmonic-damping performance of two different harmonic detection methods, that are comprehensive harmonic detection and specific harmonic detection, are compared with each other. Moreover, a new compensation scheme for the comprehensive harmonic detection method is proposed to improve system stability.

  5. A state of reversible compensated ventricular dysfunction precedes pathological remodelling in response to cardiomyocyte-specific activity of angiotensin II type-1 receptor in mice

    PubMed Central

    Frentzou, Georgia A.; Drinkhill, Mark J.; Turner, Neil A.; Ball, Stephen G.; Ainscough, Justin F. X.

    2015-01-01

    ABSTRACT Cardiac dysfunction is commonly associated with high-blood-pressure-induced cardiomyocyte hypertrophy, in response to aberrant renin-angiotensin system (RAS) activity. Ensuing pathological remodelling promotes cardiomyocyte death and cardiac fibroblast activation, leading to cardiac fibrosis. The initiating cellular mechanisms that underlie this progressive disease are poorly understood. We previously reported a conditional mouse model in which a human angiotensin II type-I receptor transgene (HART) was expressed in differentiated cardiomyocytes after they had fully matured, but not during development. Twelve-month-old HART mice exhibited ventricular dysfunction and cardiomyocyte hypertrophy with interstitial fibrosis following full receptor stimulation, without affecting blood pressure. Here, we show that chronic HART activity in young adult mice causes ventricular dysfunction without hypertrophy, fibrosis or cardiomyocyte death. Dysfunction correlated with reduced expression of pro-hypertrophy markers and increased expression of pro-angiogenic markers in the cardiomyocytes experiencing increased receptor load. This stimulates responsive changes in closely associated non-myocyte cells, including the downregulation of pro-angiogenic genes, a dampened inflammatory response and upregulation of Tgfβ. Importantly, this state of compensated dysfunction was reversible. Furthermore, increased stimulation of the receptors on the cardiomyocytes caused a switch in the secondary response from the non-myocyte cells. Progressive cardiac remodelling was stimulated through hypertrophy and death of individual cardiomyocytes, with infiltration, proliferation and activation of fibroblast and inflammatory cells, leading to increased angiogenic and inflammatory signalling. Together, these data demonstrate that a state of pre-hypertrophic compensated dysfunction can exist in affected individuals before common markers of heart disease are detectable. The data also suggest that

  6. Compensation effects and relation between the activation energy of spin transition and the hysteresis loop width for an iron(ii) complex.

    PubMed

    Bushuev, Mark B; Pishchur, Denis P; Nikolaenkova, Elena B; Krivopalov, Viktor P

    2016-06-22

    The enthalpy-entropy compensation was observed for the cooperative → spin transition (the phase is a mononuclear complex [FeL2](BF4)2, L is 4-(3,5-dimethyl-1H-pyrazol-1-yl)-2-(pyridin-2-yl)-6-methylpyrimidine). The physical origin of this effect is the fact that the → spin transition is the first order phase transition accompanied by noticeable variations in the Tonset↑, ΔH and ΔS values. Higher ΔH and ΔS values are correlated with higher Tonset↑ values. The higher the enthalpy and entropy of the spin transition, the wider the hysteresis loop. The kinetic compensation effect, i.e. a linear relationship between ln A and Ea, was observed for the → spin transition. Moreover, an isokinetic relationship was detected in this system: the Arrhenius lines (ln k vs. 1/T) obtained from magnetochemical data for different samples of the phase undergoing the → transition show a common point of intersection (Tiso = 490 ± 2 K, ln kiso = -6.0 ± 0.2). The validity of this conclusion was confirmed by the Exner-Linert statistical method. This means that the isokinetic relationship and the kinetic compensation effect (ln A vs. Ea) in this system are true ones. The existence of a true kinetic compensation effect is supported independently by the fact that the hysteresis loop width for the cooperative spin transition ↔ increases with increasing activation barrier height. Estimating the energy of excitations for the phase with Tiso ∼ 490 K yields wavenumbers of ca. 340 cm(-1) corresponding to the frequencies of the stretching vibrations of the Fe(LS)-N bonds, i.e. the bonds directly involved in the mechanism of the spin transition. This is the first observation of the kinetic compensation effect (ln A vs. Ea) and the isokinetic relationship for a cooperative spin crossover system showing thermal hysteresis. Our results provide the first experimental evidence that the higher the activation barrier for the spin transition, the wider the hysteresis loop for a

  7. Space Power Amplification with Active Linearly Tapered Slot Antenna Array

    NASA Technical Reports Server (NTRS)

    Simons, Rainee N.; Lee, Richard Q.

    1993-01-01

    A space power amplifier composed of active linearly tapered slot antennas (LTSA's) has been demonstrated and shown to have a gain of 30 dB at 20 GHz. In each of the antenna elements, a GaAs monolithic microwave integrated circuit (MMIC) three-stage power amplifier is integrated with two LTSA's. The LTSA and the MMIC power amplifier has a gain of 11 dB and power added efficiency of 14 percent respectively. The design is suitable for constructing a large array using monolithic integration techniques.

  8. Naturally-occurring compensated insulin resistance selectively alters glucose transporters in visceral and subcutaneous adipose tissue without change in AS160 activation

    PubMed Central

    Waller, AP; Kohler, K; Burns, TA; Mudge, MC; Belknap, JK; Lacombe, VA

    2011-01-01

    Although the importance of adipose tissue (AT) glucose transport in regulating whole-body insulin sensitivity is becoming increasingly evident and insulin resistance (IR) has been widely recognized, the underlying mechanisms of IR are still not well understood. The purpose of the present study was to determine the early pathological changes in glucose transport by characterizing the alterations in glucose transporters (GLUT) in multiple visceral and subcutaneous adipose depots in a large animal model of naturally-occurring compensated IR. AT biopsies were collected from horses, which were classified as insulin-sensitive (IS) or compensated IR based on the results of an insulin-modified frequently-sampled intravenous glucose tolerance test. Protein expression of GLUT4 (major isoform) and GLUT12 (one of the most recently discovered isoforms) were measured by Western blotting in multiple AT depots, as well as AS160 (a potential key player in GLUT trafficking pathway). Using a biotinylated bis-mannose photolabeled technique, active cell surface GLUT content was quantified. Omental AT had the highest total GLUT content compared to other sites during the IS state. IR was associated with a significantly reduced total GLUT4 content in omental AT, without a change in content in other visceral or subcutaneous adipose sites. In addition, active cell surface GLUT-4, but not -12, was significantly lower in AT of IR compared to IS horses, without change in AS160 phosphorylation between groups. Our data suggest that GLUT4, but not GLUT12, is a pathogenic factor in AT during naturally-occurring compensated IR, despite normal AS160 activation. PMID:21352908

  9. On a chaotic potential at the surface of a compensated semiconductor under conditions of the self-assembly of electrically active defects

    SciTech Connect

    Bondarenko, V. B. Filimonov, A. V.

    2015-09-15

    Natural irregularities of the electric potential on the surface of a semiconductor under conditions of the partial self-assembly of electrically active defects, i.e., on the formation of donor–acceptor pairs in depletion layers, are studied. The amplitude and character of the spatial distribution of the chaotic potential on the surface of a semiconductor in the cases of localized and delocalized states are determined. The dependence of the amplitude of the chaotic potential on the degree of compensation of the semiconductor is obtained.

  10. Optical tracking telescope compensation

    NASA Technical Reports Server (NTRS)

    Gilbart, J. W.

    1973-01-01

    In order to minimize the effects of parameter variations in the dynamics of an optical tracking telescope, a model referenced parameter adaptive control system is described that - in conjunction with more traditional forms of compensation - achieves a reduction of rms pointing error by more than a factor of six. The adaptive compensation system utilizes open loop compensation, closed loop compensation, and model reference compensation to provide the precise input to force telescope axis velocity to follow the ideal velocity.

  11. Temperature-compensated crystal oscillator simulation in stress compensated cut crystal resonators

    NASA Astrophysics Data System (ADS)

    Haga, Ryo; Hayashi, Rifwa; Hanada, Yosuke; Sato, Takayuki; Watanabe, Yasuaki

    2016-07-01

    Traditional quartz crystal frequency references include a large, power-starving, oven-controlled crystal oscillator (OCXO), which base stations favor because of their excellent stability. We simulated a temperature-compensated crystal oscillator (TCXO) in the stress-compensated cut (SC-cut) resonator using the C and B mode frequencies. Power-conscious base-station manufacturers use the compensation circuit combination of TCXOs. The large frequency change in the B mode will be employed in temperature compensation for the C mode. First, we examined the circuit that could drive the C mode and B mode by simulation at the same time.

  12. Power Subsystem for Extravehicular Activities for Exploration Missions

    NASA Technical Reports Server (NTRS)

    Manzo, Michelle

    2005-01-01

    The NASA Glenn Research Center has the responsibility to develop the next generation space suit power subsystem to support the Vision for Space Exploration. Various technology challenges exist in achieving extended duration missions as envisioned for future lunar and Mars mission scenarios. This paper presents an overview of ongoing development efforts undertaken at the Glenn Research Center in support of power subsystem development for future extravehicular activity systems.

  13. A high power active circulator using GaN MMIC power amplifiers

    NASA Astrophysics Data System (ADS)

    Liming, Gu; Wenquan, Che; Huang, Fan-Hsiu; Chiu, Hsien-Chin

    2014-11-01

    This paper presents a 2.4 GHz hybrid integrated active circulator consisting of three power amplifiers and three PCB-based Wilkinson power dividers. The power amplifiers were designed and fabricated in a standard 0.35-μm AlGaN/GaN HEMT technology, and combined with three traditional power dividers on FR4 using bonding wires. Due to the isolation of power dividers, the isolation between three ports is achieved; meanwhile, due to the unidirectional characteristics of the power amplifiers, the nonreciprocal transfer characteristic of the circulator is realized. The measured insertion gain of the proposed active circulator is about 2-2.7 dB at the center frequency of 2.4 GHz, the isolation between three ports is better than 20 dB over 1.2-3.4 GHz, and the output power of the designed active circulator achieves up to 20.1-21.2 dBm at the center frequency.

  14. Polarization compensator for optical communications

    NASA Technical Reports Server (NTRS)

    Fitzmaurice, M. W.; Abshire, J. B. (Inventor)

    1976-01-01

    An optical data communication system is provided whereby two orthogonal polarization states of a light beam carrier correspond to digital states. In such a system, automatic polarization compensation is provided by applying a dither modulating voltage to a cell exhibiting the electro-optic effect. The cell controls the relative phase of electric field components of an input light beam enabling the dither frequency component of the difference of the instantaneous powers in the two polarization states to be coherently detected. A signal derived from the coherent detection process is fed back to the cell via an integrator to form polarization bias compensating servo loop ot Type 1.

  15. Optimal active power dispatch by network flow approach

    SciTech Connect

    Carvalho, M.F. ); Soares, S.; Ohishi, T. )

    1988-11-01

    In this paper the optimal active power dispatch problem is formulated as a nonlinear capacitated network flow problem with additional linear constraints. Transmission flow limits and both Kirchhoff's laws are taken into account. The problem is solved by a Generalized Upper Bounding technique that takes advantage of the network flow structure of the problem. The new approach has potential applications on power systems problems such as economic dispatch, load supplying capability, minimum load shedding, and generation-transmission reliability. The paper also reviews the use of transportation models for power system analysis. A detailed illustrative example is presented.

  16. Gamma power is phase-locked to posterior alpha activity.

    PubMed

    Osipova, Daria; Hermes, Dora; Jensen, Ole

    2008-01-01

    Neuronal oscillations in various frequency bands have been reported in numerous studies in both humans and animals. While it is obvious that these oscillations play an important role in cognitive processing, it remains unclear how oscillations in various frequency bands interact. In this study we have investigated phase to power locking in MEG activity of healthy human subjects at rest with their eyes closed. To examine cross-frequency coupling, we have computed coherence between the time course of the power in a given frequency band and the signal itself within every channel. The time-course of the power was calculated using a sliding tapered time window followed by a Fourier transform. Our findings show that high-frequency gamma power (30-70 Hz) is phase-locked to alpha oscillations (8-13 Hz) in the ongoing MEG signals. The topography of the coupling was similar to the topography of the alpha power and was strongest over occipital areas. Interestingly, gamma activity per se was not evident in the power spectra and only became detectable when studied in relation to the alpha phase. Intracranial data from an epileptic subject confirmed these findings albeit there was slowing in both the alpha and gamma band. A tentative explanation for this phenomenon is that the visual system is inhibited during most of the alpha cycle whereas a burst of gamma activity at a specific alpha phase (e.g. at troughs) reflects a window of excitability. PMID:19098986

  17. Compensation Review Analyst

    2003-06-03

    COMPERA is a decision support system designed to facilitate the compensation review process. With parameters provided by the user(s), the system generates recommendations for base increases and nonbase compensation that strives to align total compensation with performance compensation targets. The user(s) prescribe(s) compensation targets according to performance (or value of contribution) designators. These targets are presented in look-up tables, which are then used by embedded formulas in the worksheet to determine the recommended compensation formore » each individual.« less

  18. Self-compensation in semiconductors

    NASA Astrophysics Data System (ADS)

    Tsur, Y.; Riess, I.

    1999-09-01

    The problem of self-compensation of charged dopants is analyzed. Special emphasis is given to dopants in binary oxides. It is shown that one can determine the degree of self-compensation from the properties of the host material and dopant concentration alone. It is further shown that for a native p-type semiconductor, donors are compensated, mostly, by native ionic defects. On the other hand, doping with acceptors allows us to increase significantly the hole concentration, i.e., self-compensation is low under high doping levels. For a native n-type semiconductor the opposite is true, namely, extrinsic acceptors are mainly compensated by native ionic defects. It is shown that the changes in concentration of all the charged defects are simply related by a single factor, the doping factor f, or its power fk where k depends solely on the defect's charge. Quantitative calculations of f and defect concentrations are presented for Cu2O, which was used as a model material. It is found that for p-type Cu2O doping with donors results in f within the range of 1-10, depending on the dopant concentration and P(O2). This means that the hole concentration decreases and the electron concentration increases at most by a factor of 10. Therefore one does not expect to obtain a changeover from p- to n-type cuprous oxide by doping, under equilibrium conditions. Most of the donors are compensated by negative ionic defects. Self-compensation in the presence of amphoteric defects and Fermi level stabilization are discussed, using the former formalism.

  19. Negative voltage bandgap reference with multilevel curvature compensation technique

    NASA Astrophysics Data System (ADS)

    Xi, Liu; Qian, Liu; Xiaoshi, Jin; Yongrui, Zhao; Lee, Jong-Ho

    2016-05-01

    A novel high-order curvature compensation negative voltage bandgap reference (NBGR) based on a novel multilevel compensation technique is introduced. Employing an exponential curvature compensation (ECC) term with many high order terms in itself, in a lower temperature range (TR) and a multilevel curvature compensation (MLCC) term in a higher TR, a flattened and better effect of curvature compensation over the TR of 165 °C (‑40 to 125 °C) is realised. The MLCC circuit adds two convex curves by using two sub-threshold operated NMOS. The proposed NBGR implemented in the Central Semiconductor Manufacturing Corporation (CSMC) 0.5 μm BCD technology demonstrates an accurate voltage of ‑1.183 V with a temperature coefficient (TC) as low as 2.45 ppm/°C over the TR of 165 °C at a ‑5.0 V power supply; the line regulation is 3 mV/V from a ‑5 to ‑2 V supply voltage. The active area of the presented NBGR is 370 × 180 μm2. Project supported by the Fund of Liaoning Province Education Department (No. L2013045).

  20. A Short-Term Decrease in Nitrogenase Activity (C2H2 Reduction) Is Induced by Exposure of Soybean Shoots to Their CO2 Compensation Point.

    PubMed Central

    Vidal, R.; Gerbaud, A.; Vidal, D.; Drevon, J. J.

    1995-01-01

    Photosynthesis and nitrogenase acetylene-reducing activity (ARA) were measured in soybeans (Glycine max [L.] Merr.) in which the shoots were exposed for 48 h to 60 [mu]L L-1 CO2, a value corresponding to their CO2 compensation point. Six hours after the beginning of the light period at low CO2, the ARA started to decrease, reaching a rate of 50% of the control rate in 14 to 24 h and 20% of the control rate in 34 to 38 h after the beginning of the CO2 treatment. At these times, there was no net photosynthesis, and the transpiration rate was 20% lower than that in the control plants. An increase in the partial pressure of O2 around the nodules alleviated this inhibition of ARA. The maximal ARA achieved at 40 kPaO2 was 3 times higher than that at 20 kPa O2 and similar to the maximal ARA of the control plants. It was argued that the decrease in ARA of soybean exposed to the CO2 compensation point was due to a decrease in the nodule's permeability to O2 diffusion. PMID:12228555

  1. Plasma Switch for High-Power Active Pulse Compressor

    SciTech Connect

    Hirshfield, Jay L.

    2013-11-04

    Results are presented from experiments carried out at the Naval Research Laboratory X-band magnicon facility on a two-channel X-band active RF pulse compressor that employed plasma switches. Experimental evidence is shown to validate the basic goals of the project, which include: simultaneous firing of plasma switches in both channels of the RF circuit, operation of quasi-optical 3-dB hybrid directional coupler coherent superposition of RF compressed pulses from both channels, and operation of the X-band magnicon directly in the RF pulse compressor. For incident 1.2 ?s pulses in the range 0.63 ? 1.35 MW, compressed pulses of peak powers 5.7 ? 11.3 MW were obtained, corresponding to peak power gain ratios of 8.3 ? 9.3. Insufficient bakeout and conditioning of the high-power RF circuit prevented experiments from being conducted at higher RF input power levels.

  2. Economics of static VAR compensation. Final report

    SciTech Connect

    Alvarado, F.L.; DeMarco, C.; Jung, T.H.

    1992-09-01

    This project was initiated in anticipation of widened use of static VAR (volt-ampere-reactive) compensation on US bulk-power transmission systems to increase levels of secure power transfer. Project objectives were to deten-nine power system cost savings and reliability benefits resulting from such use. System operating cost and stability probabilities were compared with and without static VAR compensation, applying simulation techniques. For the particular system model studied, there was a 21.4 percent reduction in operating costs taking into account losses added by the static VAR compensator. A procedure was developed to compare instability probabilities for various loadings and static VAR compensator sizes on a power system. For the particular system model studied, the static VAR compensator provided a significant increase in stability but over a narrow range of loading. Static VAR compensation is one of a number of promising FACTS (Flexible AC Transmission System) technologies for handling the demands of increased power transfers on power systems where transmission lines cannot be built or as a short-term altemative to building additional lines.

  3. 7 CFR 953.25 - Expenses and compensation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Expenses and compensation. 953.25 Section 953.25... SOUTHEASTERN STATES Order Regulating Handling Administrative Committee § 953.25 Expenses and compensation... powers under this subpart. In addition, they may receive reasonable compensation at a rate recommended...

  4. 7 CFR 946.30 - Expenses and compensation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Expenses and compensation. 946.30 Section 946.30... WASHINGTON Order Regulating Handling Administrative Committee § 946.30 Expenses and compensation. Committee... their powers under this subpart. In addition, they may receive reasonable compensation at a...

  5. 7 CFR 946.30 - Expenses and compensation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Expenses and compensation. 946.30 Section 946.30... WASHINGTON Order Regulating Handling Administrative Committee § 946.30 Expenses and compensation. Committee... their powers under this subpart. In addition, they may receive reasonable compensation at a...

  6. 7 CFR 946.30 - Expenses and compensation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Expenses and compensation. 946.30 Section 946.30... WASHINGTON Order Regulating Handling Administrative Committee § 946.30 Expenses and compensation. Committee... their powers under this subpart. In addition, they may receive reasonable compensation at a...

  7. 7 CFR 953.25 - Expenses and compensation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Expenses and compensation. 953.25 Section 953.25... SOUTHEASTERN STATES Order Regulating Handling Administrative Committee § 953.25 Expenses and compensation... powers under this subpart. In addition, they may receive reasonable compensation at a rate recommended...

  8. 7 CFR 946.30 - Expenses and compensation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Expenses and compensation. 946.30 Section 946.30... WASHINGTON Order Regulating Handling Administrative Committee § 946.30 Expenses and compensation. Committee... their powers under this subpart. In addition, they may receive reasonable compensation at a...

  9. 7 CFR 953.25 - Expenses and compensation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Expenses and compensation. 953.25 Section 953.25... SOUTHEASTERN STATES Order Regulating Handling Administrative Committee § 953.25 Expenses and compensation... powers under this subpart. In addition, they may receive reasonable compensation at a rate recommended...

  10. 7 CFR 953.25 - Expenses and compensation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Expenses and compensation. 953.25 Section 953.25... SOUTHEASTERN STATES Order Regulating Handling Administrative Committee § 953.25 Expenses and compensation... powers under this subpart. In addition, they may receive reasonable compensation at a rate recommended...

  11. 7 CFR 953.25 - Expenses and compensation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Expenses and compensation. 953.25 Section 953.25... SOUTHEASTERN STATES Order Regulating Handling Administrative Committee § 953.25 Expenses and compensation... powers under this subpart. In addition, they may receive reasonable compensation at a rate recommended...

  12. 7 CFR 946.30 - Expenses and compensation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Expenses and compensation. 946.30 Section 946.30... WASHINGTON Order Regulating Handling Administrative Committee § 946.30 Expenses and compensation. Committee... their powers under this subpart. In addition, they may receive reasonable compensation at a...

  13. Assessing the Relative Contributions of Active Ankle and Knee Assistance to the Walking Mechanics of Transfemoral Amputees Using a Powered Prosthesis

    PubMed Central

    Simon, Ann M.; Hargrove, Levi J.

    2016-01-01

    Powered knee-ankle prostheses are capable of providing net-positive mechanical energy to amputees. Yet, there are limitless ways to deliver this energy throughout the gait cycle. It remains largely unknown how different combinations of active knee and ankle assistance affect the walking mechanics of transfemoral amputees. This study assessed the relative contributions of stance phase knee swing initiation, increasing ankle stiffness and powered plantarflexion as three unilateral transfemoral amputees walked overground at their self-selected walking speed. Five combinations of knee and ankle conditions were evaluated regarding the kinematics and kinetics of the amputated and intact legs using repeated measures analyses of variance. We found eliminating active knee swing initiation or powered plantarflexion was linked to increased compensations of the ipsilateral hip joint during the subsequent swing phase. The elimination of knee swing initiation or powered plantarflexion also led to reduced braking ground reaction forces of the amputated and intact legs, and influenced both sagittal and frontal plane loading of the intact knee joint. Gradually increasing prosthetic ankle stiffness influenced the shape of the prosthetic ankle plantarflexion moment, more closely mirroring the intact ankle moment. Increasing ankle stiffness also corresponded to increased prosthetic ankle power generation (despite a similar maximum stiffness value across conditions) and increased braking ground reaction forces of the amputated leg. These findings further our understanding of how to deliver assistance with powered knee-ankle prostheses and the compensations that occur when specific aspects of assistance are added/removed. PMID:26807889

  14. Assessing the Relative Contributions of Active Ankle and Knee Assistance to the Walking Mechanics of Transfemoral Amputees Using a Powered Prosthesis.

    PubMed

    Ingraham, Kimberly A; Fey, Nicholas P; Simon, Ann M; Hargrove, Levi J

    2016-01-01

    Powered knee-ankle prostheses are capable of providing net-positive mechanical energy to amputees. Yet, there are limitless ways to deliver this energy throughout the gait cycle. It remains largely unknown how different combinations of active knee and ankle assistance affect the walking mechanics of transfemoral amputees. This study assessed the relative contributions of stance phase knee swing initiation, increasing ankle stiffness and powered plantarflexion as three unilateral transfemoral amputees walked overground at their self-selected walking speed. Five combinations of knee and ankle conditions were evaluated regarding the kinematics and kinetics of the amputated and intact legs using repeated measures analyses of variance. We found eliminating active knee swing initiation or powered plantarflexion was linked to increased compensations of the ipsilateral hip joint during the subsequent swing phase. The elimination of knee swing initiation or powered plantarflexion also led to reduced braking ground reaction forces of the amputated and intact legs, and influenced both sagittal and frontal plane loading of the intact knee joint. Gradually increasing prosthetic ankle stiffness influenced the shape of the prosthetic ankle plantarflexion moment, more closely mirroring the intact ankle moment. Increasing ankle stiffness also corresponded to increased prosthetic ankle power generation (despite a similar maximum stiffness value across conditions) and increased braking ground reaction forces of the amputated leg. These findings further our understanding of how to deliver assistance with powered knee-ankle prostheses and the compensations that occur when specific aspects of assistance are added/removed. PMID:26807889

  15. Sport for All? Insight into Stratification and Compensation Mechanisms of Sporting Activity in the 27 European Union Member States

    ERIC Educational Resources Information Center

    Van Tuyckom, Charlotte; Scheerder, Jeroen

    2010-01-01

    Physical activity is an important public health issue and the benefits of an active lifestyle in relation to well-being and health have been strongly emphasised in recent years in Europe, as well as in most parts of the world. However, previous research has shown that physical activity within Europe and its member states is stratified. The present…

  16. Actively mode-locked Tm(3+)-doped silica fiber laser with wavelength-tunable, high average output power.

    PubMed

    Kneis, Christian; Donelan, Brenda; Berrou, Antoine; Manek-Hönninger, Inka; Robin, Thierry; Cadier, Benoît; Eichhorn, Marc; Kieleck, Christelle

    2015-04-01

    A diode-pumped, actively mode-locked high-power thulium (Tm3+)-doped double-clad silica fiber laser is demonstrated, providing an average output power in mode-locked (continuous wave) operation of 53 W (72 W) with a slope efficiency of 34% (38%). Mode-locking in the 6th-harmonic order was obtained by an acousto-optic modulator driven at 66 MHz without dispersion compensation. The shortest measured output pulse width was 200 ps. Owing to a diffraction grating as cavity end mirror, the central wavelength could be tuned from 1.95 to 2.13 μm. The measured beam quality in mode-locked and continuous wave operation has been close to the diffraction limit. PMID:25831360

  17. Qualification of active mechanical components for nuclear power plants

    SciTech Connect

    Allen, R.D.; Mollerus, F.J.

    1983-11-01

    The Electric Power Research Institute has undertaken a study of active safety related mechanical components in domestic nuclear plants to determine what qualification information exists and to establish a plan for qualification of those components. Active safety related mechanical components are those which undergo mechanical motion to perform a safety function. The overall objective of the study is to recommend appropriate methods and realistic criteria for the environmental, seismic and dynamic qualification of active mechanical components. This paper presents the results of progress in this project through May 1983.

  18. Large active retrodirective arrays for solar power satellites

    NASA Technical Reports Server (NTRS)

    Chernoff, R.

    1978-01-01

    An active retrodirective array (ARA) transmits a beam toward the apparent source of an illuminating signal called the pilot. The array produces the RF power. Retrodirectivity is achieved by retransmitting from each element of the array a signal whose phase is the 'conjugate' of that received by the element. Application of the ARA to the solar power satellite concept has been proposed. A method of providing a reference phase is described, called 'central phasing', which eliminates the need for a rigid structure ordinarily needed in order to realize accurate retrodirectivity.

  19. Children's Compensations for Poorly Automated Reading Skills

    ERIC Educational Resources Information Center

    Walczyk, Jeffrey J.; Marsiglia, Cheryl S.; Johns, Amanda K.; Bryan, Keli S.

    2004-01-01

    The compensatory-encoding model (CEM) postulates that readers whose decoding of words or verbal working memory capacities is inefficient can compensate so that literal comprehension of text is not deleteriously affected. However, the use of compensations may draw cognitive resources away from higher level reading activities such as comprehension…

  20. 140-fs duration and 60-W peak power blue-violet optical pulses generated by a dispersion-compensated GaInN mode-locked semiconductor laser diode using a nonlinear pulse compressor.

    PubMed

    Kono, Shunsuke; Watanabe, Hideki; Koda, Rintaro; Fuutagawa, Noriyuki; Narui, Hironobu

    2015-12-14

    Blue-violet optical pulses of 140-fs duration and 60-W peak power were obtained from a dispersion-compensated GaInN mode-locked semiconductor laser diode using a nonlinear pulse compression technique. Wavelength-dependent group velocity dispersion expressed by third-order phase dispersion was applied to the optical pulses using a pulse compressor with a spatial light modulator. The obtained optical pulses had the shortest duration ever obtained for a mode-locked semiconductor laser diode using edge-emitting type devices. PMID:26698968

  1. Field Test Result of 10MVA/20MJ SMES for Load Fluctuation Compensation

    NASA Astrophysics Data System (ADS)

    Nagaya, Shigeo; Nagata, Tatsuya; Hirano, Naoki; Tamada, Tsutomu; Nijo, Yoshio; Katagiri, Toshio; Yamane, Minoru

    SMES of the10,000kW for the power control in power system has been manufactured, and connected to a real power grid. In addition, innovative basic researches, for example, low cost converter, maintenance-free cryo-coolers, inter-locks system and so on, have also been developed. The SMES was installed in the metal rolling factory with hydro power plant. Field test has been carried out for load fluctuation compensation. SMES was able to compensate for the active power according to the fluctuating load, and confirm the situation with a smooth load change of 11kV bus of hydro power stations. In this paper, field test results are presented.

  2. Enhanced light output power of InGaN-based amber LEDs by strain-compensating AlN/AlGaN barriers

    NASA Astrophysics Data System (ADS)

    Iida, Daisuke; Lu, Shen; Hirahara, Sota; Niwa, Kazumasa; Kamiyama, Satoshi; Ohkawa, Kazuhiro

    2016-08-01

    We investigated the effect of a combined AlN/Al0.03Ga0.97N barrier on InGaN-based amber light-emitting diodes (LEDs) grown by metalorganic vapor-phase epitaxy. InGaN-based multiple quantum wells with a combined AlN/Al0.03Ga0.97N barrier showed intense photoluminescence with a narrow full-width at half-maximum. The amber LEDs with a combined AlN/Al0.03Ga0.97N barrier achieved a light output power enhanced approximately 2.5-fold at 20 mA compared to that of the LED with a combined AlN/GaN barrier, owing to the reduction of defects in InGaN active layers. Thus, the efficiency of high-In-content InGaN-based LEDs can be improved in the spectrum range of amber.

  3. Compensations during Unsteady Locomotion.

    PubMed

    Qiao, Mu; Jindrich, Devin L

    2014-12-01

    Locomotion in a complex environment is often not steady, but the mechanisms used by animals to power and control unsteady locomotion (stability and maneuverability) are not well understood. We use behavioral, morphological, and impulsive perturbations to determine the compensations used during unsteady locomotion. At the level both of the whole-body and of joints, quasi-stiffness models are useful for describing adjustments to the functioning of legs and joints during maneuvers. However, alterations to the mechanics of legs and joints often are distinct for different phases of the step cycle or for specific joints. For example, negotiating steps involves independent changes of leg stiffness during compression and thrust phases of stance. Unsteady locomotion also involves parameters that are not part of the simplest reduced-parameter models of locomotion (e.g., the spring-loaded inverted pendulum) such as moments of the hip joint. Extensive coupling among translational and rotational parameters must be taken into account to stabilize locomotion or maneuver. For example, maneuvers with morphological perturbations (increased rotational inertial turns) involve changes to several aspects of movement, including the initial conditions of rotation and ground-reaction forces. Coupled changes to several parameters may be employed to control maneuvers on a trial-by-trial basis. Compensating for increased rotational inertia of the body during turns is facilitated by the opposing effects of several mechanical and behavioral parameters. However, the specific rules used by animals to control translation and rotation of the body to maintain stability or maneuver have not been fully characterized. We initiated direct-perturbation experiments to investigate the strategies used by humans to maintain stability following center-of-mass (COM) perturbations. When walking, humans showed more resistance to medio-lateral perturbations (lower COM displacement). However, when running, humans

  4. A naturally occurring nonapeptide functionally compensates for the CP1 domain of leucyl-tRNA synthetase to modulate aminoacylation activity.

    PubMed

    Tan, Min; Yan, Wei; Liu, Ru-Juan; Wang, Meng; Chen, Xin; Zhou, Xiao-Long; Wang, En-Duo

    2012-04-15

    aaRSs (aminoacyl-tRNA synthetases) establish the rules of the genetic code by catalysing the formation of aminoacyl-tRNA. The quality control for aminoacylation is achieved by editing activity, which is usually carried out by a discrete editing domain. For LeuRS (leucyl-tRNA synthetase), the CP1 (connective peptide 1) domain is the editing domain responsible for hydrolysing mischarged tRNA. The CP1 domain is universally present in LeuRSs, except MmLeuRS (Mycoplasma mobile LeuRS). The substitute of CP1 in MmLeuRS is a nonapeptide (MmLinker). In the present study, we show that the MmLinker, which is critical for the aminoacylation activity of MmLeuRS, could confer remarkable tRNA-charging activity on the inactive CP1-deleted LeuRS from Escherichia coli (EcLeuRS) and Aquifex aeolicus (AaLeuRS). Furthermore, CP1 from EcLeuRS could functionally compensate for the MmLinker and endow MmLeuRS with post-transfer editing capability. These investigations provide a mechanistic framework for the modular construction of aaRSs and their co-ordination to achieve catalytic efficiency and fidelity. These results also show that the pre-transfer editing function of LeuRS originates from its conserved synthetic domain and shed light on future study of the mechanism. PMID:22292813

  5. Temperature compensated photovoltaic array

    DOEpatents

    Mosher, Dan Michael

    1997-11-18

    A temperature compensated photovoltaic module (20) comprised of a series of solar cells (22) having a thermally activated switch (24) connected in parallel with several of the cells (22). The photovoltaic module (20) is adapted to charge conventional batteries having a temperature coefficient (TC) differing from the temperature coefficient (TC) of the module (20). The calibration temperatures of the switches (24) are chosen whereby the colder the ambient temperature for the module (20), the more switches that are on and form a closed circuit to short the associated solar cells (22). By shorting some of the solar cells (22) as the ambient temperature decreases, the battery being charged by the module (20) is not excessively overcharged at lower temperatures. PV module (20) is an integrated solution that is reliable and inexpensive.

  6. Temperature compensated photovoltaic array

    DOEpatents

    Mosher, D.M.

    1997-11-18

    A temperature compensated photovoltaic module comprises a series of solar cells having a thermally activated switch connected in parallel with several of the cells. The photovoltaic module is adapted to charge conventional batteries having a temperature coefficient differing from the temperature coefficient of the module. The calibration temperatures of the switches are chosen whereby the colder the ambient temperature for the module, the more switches that are on and form a closed circuit to short the associated solar cells. By shorting some of the solar cells as the ambient temperature decreases, the battery being charged by the module is not excessively overcharged at lower temperatures. PV module is an integrated solution that is reliable and inexpensive. 2 figs.

  7. Compensator configurations for load currents' symmetrization

    NASA Astrophysics Data System (ADS)

    Rusinaru, D.; Manescu, L. G.; Dinu, R. C.

    2016-02-01

    This paper approaches aspects regarding the mitigation effects of asymmetries in 3-phase 3-wire networks. The measure consisting in connecting of load current symmetrization devices at the load coupling point is presented. A time-variation of compensators parameters is determined as a function of the time-recorded electrical values. The general sizing principle of the load current symmetrization reactive components is based on a simple equivalent model of the unbalanced 3-phase loads. By using these compensators a certain control of the power components transits is ensured in the network. The control is based on the variations laws of the compensators parameters as functions of the recorded electrical values: [B] = [T]·[M]. The link between compensator parameters and measured values is ensured by a transformation matrix [T] for each operation conditions of the supply network. Additional conditions for improving of energy and efficiency performance of the compensator are considered: i.e. reactive power compensation. The compensator sizing algorithm was implemented into a MATLAB environment software, which generate the time-evolution of the parameters of load current symmetrization device. The input data of application takes into account time-recording of the electrical values. By using the compensator sizing software, some results were achieved for the case of a consumer connected at 20 kV busbar of a distribution substation, during 24 hours measurement session. Even the sizing of the compensators aimed some additional network operation aspects (power factor correction) correlated with the total or major load symmetrizations, the harmonics aspects of the network values were neglected.

  8. Robust springback compensation

    NASA Astrophysics Data System (ADS)

    Carleer, Bart; Grimm, Peter

    2013-12-01

    Springback simulation and springback compensation are more and more applied in productive use of die engineering. In order to successfully compensate a tool accurate springback results are needed as well as an effective compensation approach. In this paper a methodology has been introduce in order to effectively compensate tools. First step is the full process simulation meaning that not only the drawing operation will be simulated but also all secondary operations like trimming and flanging. Second will be the verification whether the process is robust meaning that it obtains repeatable results. In order to effectively compensate a minimum clamping concept will be defined. Once these preconditions are fulfilled the tools can be compensated effectively.

  9. Toxic compensation bills.

    PubMed Central

    Anderson, R C

    1985-01-01

    Congress has demonstrated interest in toxic compensation legislation, but not enough agreement to make significant progress. Advocates of reform claim that the legal system is heavily weighed against victims who seek compensation through the courts. Proposed reforms include a compensation fund and a cause of action in federal court. Critics have questioned whether these changes in the law would represent an improvement. Existing income replacement, medical cost reimbursement, and survivor insurance programs largely cover the losses of individuals with chronic disease. Thus, the need for an additional compensation is not clear. Furthermore, experience with compensation funds such as the Black Lung Fund suggests that political rather than scientific criteria may be used to determine eligibility. Finally, under the proposed financing mechanisms the compensation funds that are being debated would not increase incentives for care in the handling of hazardous wastes or toxic substances. PMID:4085440

  10. A high frequency active voltage doubler in standard CMOS using offset-controlled comparators for inductive power transmission.

    PubMed

    Lee, Hyung-Min; Ghovanloo, Maysam

    2013-06-01

    In this paper, we present a fully integrated active voltage doubler in CMOS technology using offset-controlled high speed comparators for extending the range of inductive power transmission to implantable microelectronic devices (IMD) and radio-frequency identification (RFID) tags. This active voltage doubler provides considerably higher power conversion efficiency (PCE) and lower dropout voltage compared to its passive counterpart and requires lower input voltage than active rectifiers, leading to reliable and efficient operation with weakly coupled inductive links. The offset-controlled functions in the comparators compensate for turn-on and turn-off delays to not only maximize the forward charging current to the load but also minimize the back current, optimizing PCE in the high frequency (HF) band. We fabricated the active voltage doubler in a 0.5-μm 3M2P std . CMOS process, occupying 0.144 mm(2) of chip area. With 1.46 V peak AC input at 13.56 MHz, the active voltage doubler provides 2.4 V DC output across a 1 kΩ load, achieving the highest PCE = 79% ever reported at this frequency. In addition, the built-in start-up circuit ensures a reliable operation at lower voltages. PMID:23853321

  11. A High Frequency Active Voltage Doubler in Standard CMOS Using Offset-Controlled Comparators for Inductive Power Transmission

    PubMed Central

    Lee, Hyung-Min; Ghovanloo, Maysam

    2014-01-01

    In this paper, we present a fully integrated active voltage doubler in CMOS technology using offset-controlled high speed comparators for extending the range of inductive power transmission to implantable microelectronic devices (IMD) and radio-frequency identification (RFID) tags. This active voltage doubler provides considerably higher power conversion efficiency (PCE) and lower dropout voltage compared to its passive counterpart and requires lower input voltage than active rectifiers, leading to reliable and efficient operation with weakly coupled inductive links. The offset-controlled functions in the comparators compensate for turn-on and turn-off delays to not only maximize the forward charging current to the load but also minimize the back current, optimizing PCE in the high frequency (HF) band. We fabricated the active voltage doubler in a 0.5-μm 3M2P std. CMOS process, occupying 0.144 mm2 of chip area. With 1.46 V peak AC input at 13.56 MHz, the active voltage doubler provides 2.4 V DC output across a 1 kΩ load, achieving the highest PCE = 79% ever reported at this frequency. In addition, the built-in start-up circuit ensures a reliable operation at lower voltages. PMID:23853321

  12. High power VCSEL device with periodic gain active region

    NASA Astrophysics Data System (ADS)

    Ning, Y. Q., II; Qin, L.; Sun, Y. F.; Li, T.; Cui, J. J.; Peng, B.; Liu, G. Y.; Zhang, Y.; Liu, Y.; Wang, L. J.; Cui, D. F.; Xu, Z. Y.

    2007-11-01

    High power vertical cavity surface emitting lasers with large aperture have been fabricated through improving passivation, lateral oxidation and heat dissipation techniques. Different from conventional three quantum well structure, a periodic gain active region with nine quantum wells was incorporated into the VCSEL structure, with which high efficiency and high power operation were expected. The nine quantum wells were divided into three groups with each of them located at the antinodes of the cavity to enhance the coupling between the optical field and the gain region. Large aperture and bottom-emitting configuration was used to improve the beam quality and the heat dissipation. A maximum output power of 1.4W was demonstrated at CW operation for a 400μm-diameter device. The lasing wavelength shifted to 995.5nm with a FWHM of 2nm at a current of 4.8A due to the internal heating and the absence of active water cooling. A ring-shape farfield pattern was induced by the non-homogeneous lateral current distribution in large diameter device. The light intensity at the center of the ring increased with increasing current. A symmetric round light spot at the center and single transverse mode operation with a divergence angle of 16° were observed with current beyond 4.8A.

  13. Magnetic force driven six degree-of-freedom active vibration isolation system using a phase compensated velocity sensor

    SciTech Connect

    Kim, Yongdae; Park, Kyihwan; Kim, Sangyoo

    2009-04-15

    A six-axis active vibration isolation system (AVIS) is developed using voice coil actuators. Point contact configuration is employed to have an easy assembly of eight voice coil actuators to an upper and a base plates. The velocity sensor, using an electromagnetic principle that is commonly used in the vibration control, is investigated since its phase lead characteristic causes an instability problem for a low frequency vibration. The performances of the AVIS are investigated in the frequency domain and finally validated by comparing with the passive isolation system using the atomic force microscope images.

  14. Editorial Commentary: Workers' Compensation and Hip Arthroscopy.

    PubMed

    Konyves, Arpad

    2016-04-01

    Patients with active claims for workplace injuries will benefit from treatment for femoroacetabular impingement, but improvement is not as good as in the patients with sports-related injuries. Workers' Compensation patients differ from highly motivated athletes. PMID:27039683

  15. Activation analysis of the PULSAR-II fusion power reactor

    SciTech Connect

    Khater, H.Y.

    1995-12-31

    The PULSAR-II pulsed tokamak power plant design utilizes a blanket made of the vanadium alloy, V-5Cr-5Ti, and cooled with liquid lithium. The shield is made of a mixture of the low activation austenitic steel (Tenelon) and vanadium. The blanket is assumed to be replaced every 5.6 full power years (FPY) and the shield is assumed to stay in place for 30 FPY. The activity induced in the blanket at the end of its lifetime is higher than the activity induced in the shield after 30 FPY. At shutdown, the blanket and shield activities are 2678 MCi and 1747 MCi, respectively. One year after shutdown the shield activity drops to 18 MCi compared to 84 MCi for the blanket. The total decay heat generated in the blanket at the end of its lifetime is 34.7 MW and drops to 17.6 MW within an hour. At shutdown, 25.3 MW of decay heat are generated in the shield, dropping to only 0.1 MW within the first year. One week after shutdown, the values of the integrated decay heat are 1770 GJ for the blanket and 469 GJ for the shield. The radwaste classification of the reactor structure is evaluated according to both the NRC 10CFR61 and Fetter waste disposal concentration limits. After 5.6 years of irradiation, the blanket will only qualify for Class C low level waste. After 30 years of operation, the shield will also qualify for disposal as Class C waste. Only remote maintenance will be allowed inside the containment building.

  16. Active control of the resistive wall mode with power saturation

    SciTech Connect

    Li Li; Liu Yue; Liu Yueqiang

    2012-01-15

    An analytic model of non-linear feedback stabilization of the resistive wall mode is presented. The non-linearity comes from either the current or the voltage saturation of the control coil power supply. For the so-called flux-to-current control, the current saturation of active coils always results in the loss of control. On the contrary, the flux-to-voltage control scheme tolerates certain degree of the voltage saturation. The minimal voltage limit is calculated, below which the control will be lost.

  17. Temperature-Compensating Inactive Strain Gauge

    NASA Technical Reports Server (NTRS)

    Moore, Thomas C., Sr.

    1993-01-01

    Thermal contribution to output of active gauge canceled. High-temperature strain gauges include both active gauge wires sensing strains and inactive gauge wires providing compensation for thermal contributions to gauge readings. Inactive-gauge approach to temperature compensation applicable to commercially available resistance-type strain gauges operating at temperatures up to 700 degrees F and to developmental strain gauges operating at temperatures up to 2,000 degrees F.

  18. Gmti Motion Compensation

    DOEpatents

    Doerry, Armin W.

    2004-07-20

    Movement of a GMTI radar during a coherent processing interval over which a set of radar pulses are processed may cause defocusing of a range-Doppler map in the video signal. This problem may be compensated by varying waveform or sampling parameters of each pulse to compensate for distortions caused by variations in viewing angles from the radar to the target.

  19. Compensated pulsed alternator

    DOEpatents

    Weldon, William F.; Driga, Mircea D.; Woodson, Herbert H.

    1980-01-01

    This invention relates to an electromechanical energy converter with inertial energy storage. The device, a single phase, two or multi-pole alternator with stationary field coils, and a rotating armature is provided. The rotor itself may be of laminated steel for slower pulses or for faster pulses should be nonmagnetic and electrically nonconductive in order to allow rapid penetration of the field as the armature coil rotates. The armature coil comprises a plurality of power generating conductors mounted on the rotor. The alternator may also include a stationary or counterrotating compensating coil to increase the output voltage thereof and to reduce the internal impedance of the alternator at the moment of peak outout. As the machine voltage rises sinusoidally, an external trigger switch is adapted to be closed at the appropriate time to create the desired output current from said alternator to an external load circuit, and as the output current passes through zero a self-commutating effect is provided to allow the switch to disconnect the generator from the external circuit.

  20. Worker's Compensation: Will College and University Professors Be Compensated for Mental Injuries Caused by Work-Related Stress?

    ERIC Educational Resources Information Center

    Hasty, Keith N.

    1991-01-01

    The extent to which college faculty may recover compensation for debilitating mental illness resulting from stressful work-related activities is discussed. General requirements for worker's compensation claims, compensability of stress-related mental and physical illnesses, applicability of these standards to college faculty, and the current state…

  1. Observational signatures of galactic winds powered by active galactic nuclei

    NASA Astrophysics Data System (ADS)

    Nims, Jesse; Quataert, Eliot; Faucher-Giguère, Claude-André

    2015-03-01

    We predict the observational signatures of galaxy scale outflows powered by active galactic nuclei (AGN). Most of the emission is produced by the forward shock driven into the ambient interstellar medium (ISM) rather than by the reverse shock. AGN-powered galactic winds with energetics suggested by phenomenological feedback arguments should produce spatially extended ˜1-10 keV X-ray emission ˜ 1041-44 erg s- 1, significantly in excess of the spatially extended X-ray emission associated with normal star-forming galaxies. The presence of such emission is a direct test of whether AGN outflows significantly interact with the ISM of their host galaxy. We further show that even radio-quiet quasars should have a radio luminosity comparable to or in excess of the far-infrared-radio correlation of normal star-forming galaxies. This radio emission directly constrains the total kinetic energy flux in AGN-powered galactic winds. Radio emission from AGN wind shocks can also explain the recently highlighted correlations between radio luminosity and the kinematics of AGN narrow-line regions in radio-quiet quasars.

  2. Development of Shunt-Type Three-Phase Active Power Filter with Novel Adaptive Control for Wind Generators

    PubMed Central

    Chen, Ming-Hung

    2015-01-01

    This paper proposes a new adaptive filter for wind generators that combines instantaneous reactive power compensation technology and current prediction controller, and therefore this system is characterized by low harmonic distortion, high power factor, and small DC-link voltage variations during load disturbances. The performance of the system was first simulated using MATLAB/Simulink, and the possibility of an adaptive digital low-pass filter eliminating current harmonics was confirmed in steady and transient states. Subsequently, a digital signal processor was used to implement an active power filter. The experimental results indicate, that for the rated operation of 2 kVA, the system has a total harmonic distortion of current less than 5.0% and a power factor of 1.0 on the utility side. Thus, the transient performance of the adaptive filter is superior to the traditional digital low-pass filter and is more economical because of its short computation time compared with other types of adaptive filters. PMID:26451391

  3. Development of Shunt-Type Three-Phase Active Power Filter with Novel Adaptive Control for Wind Generators.

    PubMed

    Chen, Ming-Hung

    2015-01-01

    This paper proposes a new adaptive filter for wind generators that combines instantaneous reactive power compensation technology and current prediction controller, and therefore this system is characterized by low harmonic distortion, high power factor, and small DC-link voltage variations during load disturbances. The performance of the system was first simulated using MATLAB/Simulink, and the possibility of an adaptive digital low-pass filter eliminating current harmonics was confirmed in steady and transient states. Subsequently, a digital signal processor was used to implement an active power filter. The experimental results indicate, that for the rated operation of 2 kVA, the system has a total harmonic distortion of current less than 5.0% and a power factor of 1.0 on the utility side. Thus, the transient performance of the adaptive filter is superior to the traditional digital low-pass filter and is more economical because of its short computation time compared with other types of adaptive filters. PMID:26451391

  4. Metal clad active fibres for power scaling and thermal management at kW power levels.

    PubMed

    Daniel, Jae M O; Simakov, Nikita; Hemming, Alexander; Clarkson, W Andrew; Haub, John

    2016-08-01

    We present a new approach to high power fibre laser design, consisting of a polymer-free all-glass optical fibre waveguide directly overclad with a high thermal conductivity metal coating. This metal clad active fibre allows a significant reduction in thermal resistance between the active fibre and the laser heat-sink as well as a significant increase in the operating temperature range. In this paper we show the results of a detailed thermal analysis of both polymer and metal coated active fibres under thermal loads typical of kW fibre laser systems. Through several different experiments we present the first demonstration of a cladding pumped aluminium-coated fibre laser and the first demonstration of efficient operation of a cladding-pumped fibre laser at temperatures of greater than 400 °C. Finally, we highlight the versatility of this approach through operation of a passively (radiatively) cooled ytterbium fibre laser head at an output power of 405 W in a compact and ultralight package weighing less than 100 g. PMID:27505822

  5. Compensated High Temperature Strain Gage

    NASA Technical Reports Server (NTRS)

    1994-01-01

    A device for measuring strain in substrates at high temperatures in which the thermally induced apparent strain is nulled is described. Two gages are used, one active gage and one compensating gage. Both gages are placed on the substrate to be gaged; the active gage is attached such that it responds to mechanical and thermally induced apparent strain while the compensating gage is attached such that it does not respond to mechanical strain and and measures only thermally induced apparent strain. A thermal blanket is placed over the two gages to maintain the gages at the same temperature. The two gages are wired as adjacent arms of a wheatstone bridge which nulls the thermally induced apparent strain giving a true reading of the mechanical strain in the substrate.

  6. 1.6  MW peak power, 90  ps all-solid-state laser from an aberration self-compensated double-passing end-pumped Nd:YVO4 rod amplifier.

    PubMed

    Wang, Chunhua; Liu, Chong; Shen, Lifeng; Zhao, Zhiliang; Liu, Bin; Jiang, Hongbo

    2016-03-20

    In this paper a delicately designed double-passing end-pumped Nd:YVO4 rod amplifier is reported that produces 10.2 W average laser output when seeded by a 6 mW Nd:YVO4 microchip laser at a repetition rate of 70 kHz with pulse duration of 90 ps. A pulse peak power of ∼1.6  MW and pulse energy of ∼143  μJ is achieved. The beam quality is well preserved by a double-passing configuration for spherical-aberration compensation. The laser-beam size in the amplifier is optimized to prevent the unwanted damage from the high pulse peak-power density. This study provides a simple and robust picosecond all-solid-state master oscillator power amplifier system with both high peak power and high beam quality, which shows great potential in the micromachining. PMID:27140580

  7. Low-power MOEMS components for active optical systems

    NASA Astrophysics Data System (ADS)

    Castracane, James; Yan, Dong; Madison, Seth; Xu, Bai

    2004-01-01

    The eventual, widespread insertion of Micro-Opto-Electro-Mechanical Systems (MOEMS) into the marketplace rests fundamentally on the ability to produce viable components that maximize optical performance while minimizing power consumption and size. In addition, the incorporation of optical reconfigurability into custom MOEMS devices offers an extra degree of freedom not possible with conventional components. Active control of surface topology allows for one component to perform multiple functions thus reducing cost and complexity. This paper will focus on the current status of the MOEMS research program at the University at Albany Institute for Materials" (UAIM) NanoFab 200 with several examples described to illustrate component and system development. In particular, among the MOEMS research portfolio at UAIM, the development of selected MOEMS-based, active optics will be discussed. This active control of diffraction and reflection forms the basis for the utility of such devices. Leveraging the extensive research expertise on the patented MEMS Compound Grating (MCG), emphasis will be placed on the extension of the approach to novel designs, materials and fabrication methods to yield low power, high performance prototypes. The main focus of this paper is on the development of a polymer version (including sacrificial layer, in some designs) of the MCG which allows for ease of fabrication and a reduced electrostatic actuation voltage. Following a system design effort, several generations of the component were fabricated to optimize the process flow. Component metrology, electromechanical characterization and initial results of optical tests will be reported. A second example presented is the design and prototype fabrication of a spring micrograting using a customized SOI process. This highly flexible component builds on the MCG concept and yields an order of magnitude reduction in actuation voltage. These examples will be presented against a backdrop of the broad UAIM

  8. Turbulence compensation: an overview

    NASA Astrophysics Data System (ADS)

    van Eekeren, Adam W. M.; Schutte, Klamer; Dijk, Judith; Schwering, Piet B. W.; van Iersel, Miranda; Doelman, Niek J.

    2012-06-01

    In general, long range visual detection, recognition and identification are hampered by turbulence caused by atmospheric conditions. Much research has been devoted to the field of turbulence compensation. One of the main advantages of turbulence compensation is that it enables visual identification over larger distances. In many (military) scenarios this is of crucial importance. In this paper we give an overview of several software and hardware approaches to compensate for the visual artifacts caused by turbulence. These approaches are very diverse and range from the use of dedicated hardware, such as adaptive optics, to the use of software methods, such as deconvolution and lucky imaging. For each approach the pros and cons are given and it is indicated for which scenario this approach is useful. In more detail we describe the turbulence compensation methods TNO has developed in the last years and place them in the context of the different turbulence compensation approaches and TNO's turbulence compensation roadmap. Furthermore we look forward and indicate the upcoming challenges in the field of turbulence compensation.

  9. Comparative study of reference currents and DC bus voltage control for Three-Phase Four-Wire Four-Leg SAPF to compensate harmonics and reactive power with 3D SVM.

    PubMed

    Chebabhi, A; Fellah, M K; Kessal, A; Benkhoris, M F

    2015-07-01

    In this paper the performances of three reference currents and DC bus voltage control techniques for Three-Phase Four-Wire Four-Leg SAPF are compared for balanced and unbalanced load conditions. The main goals are to minimize the harmonics, reduce the magnitude of neutral current, eliminate the zero-sequence current components caused by single-phase nonlinear loads and compensate the reactive power, and on the other hand improve performances such as robustness, stabilization, trajectory pursuit, and reduce time response. The three techniques are analyzed mathematically and simulation results are compared. The techniques considered for comparative study are the PI Control, Sliding Mode Control and the Backstepping Control. Synchronous reference frame theory (SRF) in the dqo-axes is used to generate the reference currents, of the inverter. PMID:25704056

  10. The Suppression of Star Formation by Powerful Active Galactic Nuclei

    NASA Technical Reports Server (NTRS)

    Dwek, E.

    2012-01-01

    The old, red stars that constitute the bulges of galaxies, and the massive black holes at their centres, are the relics of a period in cosmic history when galaxies formed stars at remarkable rates and active galactic nuclei (AGN) shone brightly as a result of accretion onto black holes. It is widely suspected, but unproved, that the tight corre1ation between the mass of the black hole and the mas. of the stellar bulge results from the AGN quenching the surrounding star formation as it approaches its peak luminosity. X-rays trace emission from AGN unambiguously, whereas powerful star-forming ga1axies are usually dust-obscured and are brightest at infrared and submillimeter wavelengths. Here we report submillimetre and X-ray observations that show that rapid star formation was common in the host galaxies of AGN when the Universe was 2-6 billion years old, but that the most vigorous star formation is not observed around black holes above an X-ray luminosity of 10(exp 44) ergs per second. This suppression of star formation in the host galaxy of a powerful AGN is a key prediction of models in which the AGN drives an outflow, expe11ing the interstellar medium of its host and transforming the galaxy's properties in a brief period of cosmic time.

  11. The suppression of star formation by powerful active galactic nuclei.

    PubMed

    Page, M J; Symeonidis, M; Vieira, J D; Altieri, B; Amblard, A; Arumugam, V; Aussel, H; Babbedge, T; Blain, A; Bock, J; Boselli, A; Buat, V; Castro-Rodríguez, N; Cava, A; Chanial, P; Clements, D L; Conley, A; Conversi, L; Cooray, A; Dowell, C D; Dubois, E N; Dunlop, J S; Dwek, E; Dye, S; Eales, S; Elbaz, D; Farrah, D; Fox, M; Franceschini, A; Gear, W; Glenn, J; Griffin, M; Halpern, M; Hatziminaoglou, E; Ibar, E; Isaak, K; Ivison, R J; Lagache, G; Levenson, L; Lu, N; Madden, S; Maffei, B; Mainetti, G; Marchetti, L; Nguyen, H T; O'Halloran, B; Oliver, S J; Omont, A; Panuzzo, P; Papageorgiou, A; Pearson, C P; Pérez-Fournon, I; Pohlen, M; Rawlings, J I; Rigopoulou, D; Riguccini, L; Rizzo, D; Rodighiero, G; Roseboom, I G; Rowan-Robinson, M; Sánchez Portal, M; Schulz, B; Scott, D; Seymour, N; Shupe, D L; Smith, A J; Stevens, J A; Trichas, M; Tugwell, K E; Vaccari, M; Valtchanov, I; Viero, M; Vigroux, L; Wang, L; Ward, R; Wright, G; Xu, C K; Zemcov, M

    2012-05-10

    The old, red stars that constitute the bulges of galaxies, and the massive black holes at their centres, are the relics of a period in cosmic history when galaxies formed stars at remarkable rates and active galactic nuclei (AGN) shone brightly as a result of accretion onto black holes. It is widely suspected, but unproved, that the tight correlation between the mass of the black hole and the mass of the stellar bulge results from the AGN quenching the surrounding star formation as it approaches its peak luminosity. X-rays trace emission from AGN unambiguously, whereas powerful star-forming galaxies are usually dust-obscured and are brightest at infrared and submillimetre wavelengths. Here we report submillimetre and X-ray observations that show that rapid star formation was common in the host galaxies of AGN when the Universe was 2-6 billion years old, but that the most vigorous star formation is not observed around black holes above an X-ray luminosity of 10(44) ergs per second. This suppression of star formation in the host galaxy of a powerful AGN is a key prediction of models in which the AGN drives an outflow, expelling the interstellar medium of its host and transforming the galaxy's properties in a brief period of cosmic time. PMID:22575961

  12. Voltage and Current Unbalance Compensation Using a STATCOM

    SciTech Connect

    Xu, Yan; Tolbert, Leon M; Kueck, John D; Rizy, D Tom

    2010-01-01

    A three-phase insulated gate bipolar transistor (IGBT)-based static var compensator (STATCOM) is used for voltage and/or current unbalance compensation. An instantaneous power theory is adopted for real-time calculation and control. Three control schemes, current control, voltage control, and integrated control are proposed to compensate the unbalance of current, voltage, or both. The compensation results of the different control schemes in unbalance cases (load unbalance or voltage source unbalance) are compared and analyzed. The simulation and experimental results show that the control schemes can compensate the unbalance in load current or in the voltage source. Different compensation objectives can be achieved, i.e., balanced and unity power factor source current, balanced and regulated voltage, or both, by choosing appropriate control schemes.

  13. 12 CFR 150.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 1 2013-01-01 2013-01-01 false May I earn compensation for acting in a... TREASURY FIDUCIARY POWERS OF FEDERAL SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 150.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  14. 12 CFR 550.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 6 2014-01-01 2012-01-01 true May I earn compensation for acting in a... THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  15. 12 CFR 550.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 5 2010-01-01 2010-01-01 false May I earn compensation for acting in a... THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  16. 12 CFR 550.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 6 2012-01-01 2012-01-01 false May I earn compensation for acting in a... THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  17. 12 CFR 150.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 1 2012-01-01 2012-01-01 false May I earn compensation for acting in a... TREASURY FIDUCIARY POWERS OF FEDERAL SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 150.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  18. 12 CFR 150.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 1 2014-01-01 2014-01-01 false May I earn compensation for acting in a... TREASURY FIDUCIARY POWERS OF FEDERAL SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 150.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  19. 12 CFR 550.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 5 2011-01-01 2011-01-01 false May I earn compensation for acting in a... THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  20. 12 CFR 550.380 - May I earn compensation for acting in a fiduciary capacity?

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 6 2013-01-01 2012-01-01 true May I earn compensation for acting in a... THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.380 May I earn compensation for acting in a fiduciary capacity? If the amount...

  1. ACTS Rain Fade Compensation

    NASA Technical Reports Server (NTRS)

    Coney, Thom A.

    1996-01-01

    Performance status of the Adaptive Rain Fade Compensation includes: (1) The rain fade protocol is functional detecting fades, providing an additional 10 dB of margin and seamless transitions to and from coded operation; (2) The stabilization of the link margins and the optimization of rain fade decision thresholds has resulted in improved BER performance; (3) Characterization of the fade compensation algorithm is ongoing.

  2. Error-Compensated Telescope

    NASA Technical Reports Server (NTRS)

    Meinel, Aden B.; Meinel, Marjorie P.; Stacy, John E.

    1989-01-01

    Proposed reflecting telescope includes large, low-precision primary mirror stage and small, precise correcting mirror. Correcting mirror machined under computer control to compensate for error in primary mirror. Correcting mirror machined by diamond cutting tool. Computer analyzes interferometric measurements of primary mirror to determine shape of surface of correcting mirror needed to compensate for errors in wave front reflected from primary mirror and commands position and movement of cutting tool accordingly.

  3. Workers' Compensation and Teacher Stress.

    ERIC Educational Resources Information Center

    Nisbet, Michael K.

    1999-01-01

    Examines the Workers' Compensation system and teacher stress to determine if a burned-out teacher should be eligible for Workers' Compensation benefits. Concludes that although most states do not allow Workers' Compensation benefits to burned-out teachers, compensation should be granted because the injuries are real and work-related. (Contains 48…

  4. HUBBLE CAPTURES AN EXTRAORDINARY AND POWERFUL ACTIVE GALAXY

    NASA Technical Reports Server (NTRS)

    2002-01-01

    Resembling a swirling witch's cauldron of glowing vapors, the black hole-powered core of a nearby active galaxy appears in this colorful NASA Hubble Space Telescope image. The galaxy lies 13 million light-years away in the southern constellation Circinus. This galaxy is designated a type 2 Seyfert, a class of mostly spiral galaxies that have compact centers and are believed to contain massive black holes. Seyfert galaxies are themselves part of a larger class of objects called Active Galactic Nuclei or AGN. AGN have the ability to remove gas from the centers of their galaxies by blowing it out into space at phenomenal speeds. Astronomers studying the Circinus galaxy are seeing evidence of a powerful AGN at the center of this galaxy as well. Much of the gas in the disk of the Circinus spiral is concentrated in two specific rings -- a larger one of diameter 1,300 light-years, which has already been observed by ground-based telescopes, and a previously unseen ring of diameter 260 light-years. In the Hubble image, the smaller inner ring is located on the inside of the green disk. The larger outer ring extends off the image and is in the plane of the galaxy's disk. Both rings are home to large amounts of gas and dust as well as areas of major 'starburst' activity, where new stars are rapidly forming on timescales of 40 - 150 million years, much shorter than the age of the entire galaxy. At the center of the starburst rings is the Seyfert nucleus, the believed signature of a supermassive black hole that is accreting surrounding gas and dust. The black hole and its accretion disk are expelling gas out of the galaxy's disk and into its halo (the region above and below the disk). The detailed structure of this gas is seen as magenta-colored streamers extending towards the top of the image. In the center of the galaxy and within the inner starburst ring is a V-shaped structure of gas. The structure appears whitish-pink in this composite image, made up of four filters. Two

  5. Beyond negligence: avoidability and medical injury compensation.

    PubMed

    Kachalia, Allen B; Mello, Michelle M; Brennan, Troyen A; Studdert, David M

    2008-01-01

    Disenchantment with the tort system and negligence standard in the United States is fueling interest in alternate compensation systems for medical injury. One possibility is experimentation with administrative "health courts," through which specialized adjudicators would utilize neutral experts to render compensability determinations. Compensation would be based not on negligence, but rather on a broader avoidable medical injury (avoidability) standard. Although considerable interest in health courts exists, stakeholders frequently express uncertainty about the meaning and operation of an avoidability standard. Three nations-Sweden, Denmark, and New Zealand-have long operated administrative schemes. We conducted interviews with administrators and stakeholders in these systems. Our goal was to garner lessons on how to operate a health court, and specifically, how to develop and apply alternate compensation criteria such as avoidability. This article reports our findings on the origins and operations of the systems, the evolution of their compensation criteria, and how these criteria are actually applied. We found that all three systems had their primary genesis in ensuring compensation for the injured, as opposed to sanctioning providers. All have abandoned the negligence standard. The Nordic systems use an avoidability standard, principally defined as injury that would not occur in the hands of the best practitioner. Their experience demonstrates that this definition is feasible to apply. New Zealand's recent move to a no-fault system sheds light on the benefits and drawbacks of a variety of compensation standards. Key lessons for successfully applying an alternate standard, such as avoidability, include a strict adherence to national precedent, the use of neutral and experienced experts, and a block on routine transfer of information from compensation investigations to disciplinary authorities. Importantly, all three nations are harnessing their systems' power to

  6. 76 FR 60132 - Proposed Information Collection (Application for Dependency and Indemnity Compensation by Parent...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-28

    ...), (Including Accrued Benefits and Death Compensation)) Activity: Comment Request AGENCY: Veterans Benefits... needed to determine a claimant's eligibility for dependency and indemnity compensation, death... Compensation by Parent(s), (Including Accrued Benefits and Death Compensation), VA Form 21-535. OMB...

  7. A home-baked temperature-compensated integrated light sensor on silicon

    NASA Astrophysics Data System (ADS)

    Gourdeas, Leon; James, Daniel A.; Davey, Neil P.

    2004-03-01

    Integrated smart sensors are quickly becoming an industry norm and often require multi-stage, multi-skilled design. This paper describes the fabrication of a temperature compensated light sensor using only a basic fabrication laboratory. A complete description of how to build the sensing elements, support electronics and communications is described and test results are presented. The construction of a light sensor using a shottkey barrier diode between the nickel and n-type silicon has been previously described by the authors. In this two such sensors are used as active and passive sensor elements to compensate for temperature effects. The outputs from each are differentially amplified, conditioned and buffered using an LM324 die to provide a temperature compensated output. Further reduction in size is possible when the temperature sensors are mounted front to back on a single silicon substrate and coupled directly to the LM324 die. External communications are only power, ground and an analogue signal.

  8. 97. Photocopied August 1978. COMPENSATING GATES SITE, SEPTEMBER 7, 1915, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    97. Photocopied August 1978. COMPENSATING GATES SITE, SEPTEMBER 7, 1915, LOOKING NORTH AT EAST END. THIS PHOTO GIVES A GOOD VIEW OF THE CONSTRUCTION OF THE COFFER DAM AS WELL AS THE COMPLETED PIERS OF THE COMPENSATING GATES PRIOR TO THE INSTALLATION OF THE SUPER-STRUCTURE. (627) - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

  9. Compensation in Higher Education. ERIC/Higher Education Research Currents.

    ERIC Educational Resources Information Center

    Trivett, David A.

    Compensation in higher education is an inclusive term, since all the benefits associated with teaching, research, work with people, and work with knowledge might be included. But in terms of purchasing power it appears that compensation for work in higher education has lost ground against inflation. In contrast, wage and salary earners in many…

  10. 18 CFR 367.29 - Compensation for use of capital.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... capital. 367.29 Section 367.29 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... ACT General Instructions § 367.29 Compensation for use of capital. A servicing transaction is deemed... allocation of expenses plus reasonable compensation for necessary capital procured through the issuance...

  11. Powerful Low-Frequency Vibrators for Active Seismology

    SciTech Connect

    Alekseev, A.S.; Chichinin, I.S.; Korneev, V.A.

    2003-12-01

    In the past two decades, active seismology studies in Russia have made use of powerful (40- and 100-ton) low-frequency vibrators. These sources create a force amplitude of up to 100 tons and function in the 1.5 3, 3 6, and 5 10 Hz frequency bands. The mobile versions of the vibrator have a force amplitude of 40 tons and a 6 12 Hz frequency band. Recording distances for the 100-ton vibrator are as large as 350 km, enabling the refracted waves to penetrate down to 50 km depths. Vibrator operation sessions are highly repeatable, having distinct summer or winter spectral patterns. A long profile of seismic records allows estimation of fault zone depths using changes in recorded spectra. Other applications include deep seismic profiling, seismic hazard mapping, structural testing, stress-induced anisotropy studies, seismic station calibration, and large-structure integrity testing. The theoretical description of the low-frequency vibrator is given in the appendices, which contain numerical examples.

  12. Catalytic combustion of dry carbon monoxide by external power activation

    NASA Astrophysics Data System (ADS)

    Treviño, C.; Prince, J. C.

    2000-03-01

    The catalytic combustion of dry carbon monoxide and air in a planar stagnation-point flow over a platinum foil with external power is studied in this paper. The reduced heterogeneous kinetics are modelled with the dissociative adsorption of the molecular oxygen and the non-dissociative adsorption of CO, together with a surface reaction of the Langmuir-Hinshelwood type and the desorption reaction of the adsorbed product, CO 2(s). The resulting governing equations have been numerically integrated and the whole S-shaped response curve has been obtained as a function of the mixture initial concentration. The critical conditions for the catalytic ignition and extinction are deduced using high activation energy asymptotics of the desorption kinetics of the most efficient adsorbed reactant, CO(s). We obtained a very good agreement between the numerical and asymptotic results for the ignition and extinction conditions. In general, the ignition process can be well modelled without reactant consumption, while extinction occurs in the partial diffusion-controlled regime, with a finite non-zero concentration of carbon monoxide close to the plate.

  13. Active compensation of aperture discontinuities for WFIRST-AFTA: analytical and numerical comparison of propagation methods and preliminary results with a WFIRST-AFTA-like pupil

    NASA Astrophysics Data System (ADS)

    Mazoyer, Johan; Pueyo, Laurent; Norman, Colin; N'Diaye, Mamadou; van der Marel, Roeland P.; Soummer, Rémi

    2016-03-01

    The new frontier in the quest for the highest contrast levels in the focal plane of a coronagraph is now the correction of the large diffraction artifacts introduced at the science camera by apertures of increasing complexity. Indeed, the future generation of space- and ground-based coronagraphic instruments will be mounted on on-axis and/or segmented telescopes; the design of coronagraphic instruments for such observatories is currently a domain undergoing rapid progress. One approach consists of using two sequential deformable mirrors (DMs) to correct for aberrations introduced by secondary mirror structures and segmentation of the primary mirror. The coronagraph for the WFIRST-AFTA mission will be the first of such instruments in space with a two-DM wavefront control system. Regardless of the control algorithm for these multiple DMs, they will have to rely on quick and accurate simulation of the propagation effects introduced by the out-of-pupil surface. In the first part of this paper, we present the analytical description of the different approximations to simulate these propagation effects. In Appendix A, we prove analytically that in the special case of surfaces inducing a converging beam, the Fresnel method yields high fidelity for simulations of these effects. We provide numerical simulations showing this effect. In the second part, we use these tools in the framework of the active compensation of aperture discontinuities (ACAD) technique applied to pupil geometries similar to WFIRST-AFTA. We present these simulations in the context of the optical layout of the high-contrast imager for complex aperture telescopes, which will test ACAD on a optical bench. The results of this analysis show that using the ACAD method, an apodized pupil Lyot coronagraph, and the performance of our current DMs, we are able to obtain, in numerical simulations, a dark hole with a WFIRST-AFTA-like. Our numerical simulation shows that we can obtain contrast better than 2×10-9 in

  14. Power budget considerations for optically activated conventional sensors and actuators

    NASA Astrophysics Data System (ADS)

    Liu, Kexing

    1991-02-01

    Optically powered conventional instrumentation with optical fiber links that combine the advantages of a familiar technology and of fiber optics is described. A number of examples are given of the development of pneumatic pressure sensors and actuators with reduced power consumption that are operated by optical power and incorporated with fiber-optic links. Their performance and power budget are discussed. They are particularly applicable to transmissions through regions having high EM interference, high EM pulses, and explosive, radiative, or corrosive hazards, such as in nuclear power plants, process plants, aircraft, or spacecraft. These low-optical-power transmission and operation characteristics will help to meet safety requirements and to reduce the system cost.

  15. Compilation of Trade Studies for the Constellation Program Extravehicular Activity Spacesuit Power System

    NASA Technical Reports Server (NTRS)

    Fincannon, James

    2009-01-01

    This compilation of trade studies performed from 2005 to 2006 addressed a number of power system design issues for the Constellation Program Extravehicular Activity Spacesuit. Spacesuits were required for spacewalks and in-space activities as well as lunar and Mars surface operations. The trades documented here considered whether solar power was feasible for spacesuits, whether spacesuit power generation should be a distributed or a centralized function, whether self-powered in-space spacesuits were better than umbilically powered ones, and whether the suit power system should be recharged in place or replaced.

  16. Fast Responding Voltage Regulator and Dynamic VAR Compensator

    SciTech Connect

    Divan, Deepak; Moghe, Rohit; Tholomier, Damien

    2014-12-31

    The objectives of this project were to develop a dynamic VAR compensator (DVC) for voltage regulation through VAR support to demonstrate the ability to achieve greater levels of voltage control on electricity distribution networks, and faster response compared to existing grid technology. The goal of the project was to develop a prototype Fast Dynamic VAR Compensator (Fast DVC) hardware device, and this was achieved. In addition to developing the dynamic VAR compensator device, Varentec in partnership with researchers at North Carolina State University (NCSU) successfully met the objectives to model the potential positive impact of such DVCs on representative power networks. This modeling activity validated the ability of distributed dynamic VAR compensators to provide fast voltage regulation and reactive power control required to respond to grid disturbances under high penetration of fluctuating and intermittent distributed energy resources (DERs) through extensive simulation studies. Specifically the following tasks were set to be accomplished: 1) Development of dynamic VAR compensator to support dynamic voltage variations on the grid through VAR control 2) Extensive testing of the DVC in the lab environment 3) Present the operational DVC device to the DOE at Varentec’s lab 4) Formulation of a detailed specification sheet, unit assembly document, test setup document, unit bring-up plan, and test plan 5) Extensive simulations of the DVC in a system with high PV penetration. Understanding the operation with many DVC on a single distribution system 6) Creation and submittal of quarterly and final reports conveying the design documents, unit performance data, modeling simulation charts and diagrams, and summary explanations of the satisfaction of program goals. This report details the various efforts that led to the development of the Fast DVC as well as the modeling & simulation results. The report begins with the introduction in Section II which outlines the

  17. 36 CFR 1211.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... RULES NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities... basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results in the...

  18. 22 CFR 146.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Compensation. 146.515 Section 146.515 Foreign Relations DEPARTMENT OF STATE CIVIL RIGHTS NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities...

  19. 31 CFR 28.515 - Compensation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... a rate less than that paid to employees of the opposite sex for equal work on jobs the performance... SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities Prohibited § 28.515 Compensation....

  20. 36 CFR 1211.515 - Compensation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... RULES NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities... basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results in the...

  1. 31 CFR 28.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... a rate less than that paid to employees of the opposite sex for equal work on jobs the performance... SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or Activities Prohibited § 28.515 Compensation....

  2. Large Capacity SMES for Voltage Dip Compensation

    NASA Astrophysics Data System (ADS)

    Iwatani, Yu; Saito, Fusao; Ito, Toshinobu; Shimada, Mamoru; Ishida, Satoshi; Shimanuki, Yoshio

    Voltage dips of power grids due to thunderbolts, snow damage, and so on, cause serious damage to production lines of precision instruments, for example, semiconductors. In recent years, in order to solve this problem, uninterruptible power supply systems (UPS) are used. UPS, however, has small capacity, so a great number of UPS are needed in large factories. Therefore, we have manufactured the superconducting magnetic energy storage (SMES) system for voltage dip compensation able to protect loads with large capacity collectively. SMES has advantages such as space conservation, long lifetime and others. In field tests, cooperating with CHUBU Electric Power Co., Inc. we proved that SMES is valuable for compensating voltage dips. Since 2007, 10MVA SMES improved from field test machines has been running in a domestic liquid crystal display plant, and in 2008, it protected plant loads from a number of voltage dips. In this paper, we report the action principle and components of the improved SMES for voltage dip compensation, and examples of waveforms when 10MVA SMES compensated voltage dips.

  3. Modeling of power and energy transduction of embedded piezoelectric wafer active sensors for structural health monitoring

    NASA Astrophysics Data System (ADS)

    Lin, Bin; Giurgiutiu, Victor

    2010-04-01

    This paper presents a systematic investigation of power and energy transduction in piezoelectric wafer active sensors (PWAS) for structural health monitoring (SHM). After a literature review of the state of the art, the paper develops a simplified pitch-catch model of power and energy transduction of PWAS attached to structure. The model assumptions include: (a) 1-D axial and flexural wave propagation; (b) ideal bonding (pin-force) connection between PWAS and structure; (c) ideal excitation source at the transmitter PWAS and fully-resistive external load at the receiver PWAS. Frequency response functions are developed for voltage, current, complex power, active power, etc. First, we examined PWAS transmitter and determined the active power, reactive power, power rating of electrical requirement under harmonic voltage excitation. It was found that the reactive power is dominant and defines the power requirement for power supply / amplifier for PWAS applications. The electrical and mechanical power analysis at the PWAS structure interface indicates all the active electrical power provides the mechanical power at the interface. This provides the power and energy for the axial and flexural waves power and energy that propagate into the structure. The sum of forward and backward wave power equals the mechanical power PWAS applied to the structure. The parametric study of PWAS transmitter size shows the proper size and excitation frequency selection based on the tuning effects. Second, we studied the PWAS receiver structural interface acoustic and electrical energy transduction. The parametric study of receiver size, receiver impedance and external electrical load gives the PWAS design guideline for PWAS sensing and power harvesting applications. Finally we considered the power flow for a complete pitch-catch setup. In pitch-catch mode, the power flows from electrical source into piezoelectric power at the transmitter; the piezoelectric conduction converts the electrical

  4. Backlash compensator mechanism

    DOEpatents

    Chrislock, Jerry L.

    1979-01-01

    Mechanism which compensates for backlash error in a lead screw position indicator by decoupling the indicator shaft from the lead screw when reversing rotation. The position indicator then displays correct information regardless of the direction of rotation of the lead screw.

  5. Teacher Compensation and Organization.

    ERIC Educational Resources Information Center

    Kelley, Carolyn

    1997-01-01

    Examines changes in the conceptualization of schooling over time from an organizational perspective. Explores how compensation systems might be better designed to match alternative organizational designs, considering scientific management, effective schools, content-driven schooling, and high standards/high involvement schools as organizational…

  6. The Compensation Question

    ERIC Educational Resources Information Center

    Richwine, Jason; Biggs, Andrew; Mishel, Lawrence; Roy, Joydeep

    2012-01-01

    Over the past few years, as cash-strapped states and school districts have faced tough budget decisions, spending on teacher compensation has come under the microscope. The underlying question is whether, when you take everything into account, today's teachers are fairly paid, underpaid, or overpaid. In this forum, two pairs of respected…

  7. Instantaneous Active and Nonactive Power Control of Distributed Energy Resources with Current Limiter

    SciTech Connect

    Xu, Yan; Li, Huijuan; Rizy, D Tom; Li, Fangxing; Kueck, John D

    2010-01-01

    Abstract -- Distributed energy resources (DER) with a power electronics inverter interface can provide both active power and nonactive power simultaneously and independently. A decoupled control algorithm of active power and nonactive power is developed based on the instantaneous active power and nonactive power theory. A current limiter is combined to the control algorithm, and it ensures that the inverter is not overloaded. During the normal system operation, the active power has higher priority over the nonactive power so that the energy from a DER can be fully transferred to the grid. Within the inverter s capability, nonactive power is provided to the grid as required. With this control algorithm, the inverter s capabilities are taken full advantage at all times, both in terms of functionality as well as making use of its full KVA rating. Through the algorithm, the inverter s active power and nonactive power are controlled directly, simultaneously, and independently. Several experimental results fully demonstrate the validity and effectiveness of this new control algorithm. As evidenced by the fast dynamic response that results, a DER system with the control algorithm can provide full services to the grid in both steady state and during transient events.

  8. Active high-power RF switch and pulse compression system

    DOEpatents

    Tantawi, Sami G.; Ruth, Ronald D.; Zolotorev, Max

    1998-01-01

    A high-power RF switching device employs a semiconductor wafer positioned in the third port of a three-port RF device. A controllable source of directed energy, such as a suitable laser or electron beam, is aimed at the semiconductor material. When the source is turned on, the energy incident on the wafer induces an electron-hole plasma layer on the wafer, changing the wafer's dielectric constant, turning the third port into a termination for incident RF signals, and. causing all incident RF signals to be reflected from the surface of the wafer. The propagation constant of RF signals through port 3, therefore, can be changed by controlling the beam. By making the RF coupling to the third port as small as necessary, one can reduce the peak electric field on the unexcited silicon surface for any level of input power from port 1, thereby reducing risk of damaging the wafer by RF with high peak power. The switch is useful to the construction of an improved pulse compression system to boost the peak power of microwave tubes driving linear accelerators. In this application, the high-power RF switch is placed at the coupling iris between the charging waveguide and the resonant storage line of a pulse compression system. This optically controlled high power RF pulse compression system can handle hundreds of Megawatts of power at X-band.

  9. Isostatic compensation of equatorial highlands on Venus

    NASA Technical Reports Server (NTRS)

    Kucinskas, Algis B.; Turcotte, Donald L.

    1994-01-01

    Spherical harmonic models for Venus' global topography and gravity incorporating Magellan data are used to test isostatic compensation models in five 30 deg x 30 deg regions representative of the main classes of equatorial highlands. The power spectral density for the harmonic models obeys a power-law scaling with spectral slope Beta approximately 2 (Brown noise) for the topography and Beta approximately 3 (Kaula's law) for the geoid, similar to what is observed for Earth. The Venus topography spectrum has lower amplitudes than Earth's which reflects the dominant lowland topography on Venus. Observed degree geoid to topography ratios (GTRs) on Venus are significantly smaller than degree GTRs for uncompensated topography, indicative of substantial compensation. Assuming a global Airy compensation, most of the topography is compensated at depths greater than 100 km, suggesting a thick lithosphere on Venus. For each region considered we obtain a regional degree of compensation C from a linear regression of Bouguer anomaly versus Bouguer gravity data. Geoid anomaly (N) versus topography variation (h) data for each sample were compared, in the least-squares sense, to theoretical correlations for Pratt, Airy, and thermal thinning isostasy models yielding regional GTR, zero-elevation crustal thickness (H), and zero elevation thermal lithosphere thickness (y(sub L(sub 0)), respectively. We find the regional compensation to be substantial (C approximately 52-80%), and the h, N data correlations in the chosen areas can be explained by isostasy models applicable on the Earth and involving variations in crustal thickness (Airy) and/or lithospheric (thermal thinning) thickness. However, a thick crust and lithosphere (y(sub L(sub 0)) approximately 300 km) must be assumed for Venus.

  10. Intracellular shunting of O{sub 2}{sup −} contributes to charge compensation and preservation of neutrophil respiratory burst in the absence of voltage-gated proton channel activity

    SciTech Connect

    Decleva, Eva; Menegazzi, Renzo; Fasolo, Alba; Defendi, Federica

    2013-07-15

    Proton efflux via voltage-gated proton channels (Hv1) is considered to mediate the charge compensation necessary to preserve NADPH oxidase activity during the respiratory burst. Using the Hv1 inhibitor Zn{sup 2+}, we found that the PMA-induced respiratory burst of human neutrophils is inhibited when assessed as extracellular production of O{sub 2}{sup −} and H{sub 2}O{sub 2}, in accordance with literature studies, but, surprisingly, unaffected when measured as oxygen consumption or total (extracellular plus intracellular) H{sub 2}O{sub 2} production. Furthermore, we show that inhibiting Hv1 with Zn{sup 2+} results in an increased production of intracellular ROS. Similar results, i.e. decreased extracellular and increased intracellular ROS production, were obtained using a human granulocyte-like cell line with severely impaired Hv1 expression. Acidic extracellular pH, which dampens proton efflux, also augmented intracellular production of H{sub 2}O{sub 2}. Zinc caused an increase in the rate but not in the extent of depolarization and cytosolic acidification indicating that mechanisms other than proton efflux take part in charge compensation. Our results suggest a hitherto unpredicted mechanism of charge compensation whereby, in the absence of proton efflux, part of O{sub 2}{sup −} generated within gp91{sup phox} in the plasma membrane is shunted intracellularly down electrochemical gradient to dampen excessive depolarization. This would preserve NADPH oxidase activity under conditions such as the inflammatory exudate in which the acidic pH hinders charge compensation by proton efflux. Highlights: • Neutrophils’ respiratory burst is not inhibited by the H{sup +} channel inhibitor Zn{sup 2+}. • Intracellular production of O{sub 2}{sup −} and H{sub 2}O{sub 2} is increased in the presence of Zn{sup 2+}. • Intracellular H{sub 2}O{sub 2} production is increased in H{sup +} channels knock-down cells. • Zn{sup 2+} increases the rate but not the extent of

  11. Impaired voluntary neuromuscular activation limits muscle power in mobility-limited older adults

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Background. Age-related alterations of neuromuscular activation may contribute to deficits in muscle power and mobility function. This study assesses whether impaired activation of the agonist quadriceps and antagonist hamstrings, including amplitude- and velocity-dependent characteristics of activa...

  12. AUV-portable temperature-compensating fiber optic hydrophone

    NASA Astrophysics Data System (ADS)

    Saxena, Indu Fiesler; Guzman, Narciso; Hui, Kaleonui J.; Pflanze, Stephen

    2011-06-01

    Passive acoustic monitoring hydrophones with low power consumption for autonomous underwater vehicles (AUVs) are desirable for long term unmanned monitoring of ocean acoustics including marine mammal acoustics as well as those due to human activity. Fiber-optic hydrophones offer wider bandwidth and high sensitivity alternatives to conventional piezoelectric transducer (PZT) devices. Deployment on board AUVs requires operation under a wide range of temperature and pressure conditions that change with depth and location, hence, maintaining the sensitivity and reliability over the operating range is crucial. A read-out mechanism for a resonant hydrophone using a fiber Bragg grating (FBG) transducer is described. The read-out uses a temperature tuned DFB laser diode to compensate for FBG changes with temperature and depth, enabling operation over a wide temperature range. Its compact footprint and battery-powered readout system operation enables portability on AUVs.

  13. Active impedance matching of complex structural systems

    NASA Technical Reports Server (NTRS)

    Macmartin, Douglas G.; Miller, David W.; Hall, Steven R.

    1991-01-01

    Viewgraphs on active impedance matching of complex structural systems are presented. Topics covered include: traveling wave model; dereverberated mobility model; computation of dereverberated mobility; control problem: optimal impedance matching; H2 optimal solution; statistical energy analysis (SEA) solution; experimental transfer functions; interferometer actuator and sensor locations; active strut configurations; power dual variables; dereverberation of complex structure; dereverberated transfer function; compensators; and relative power flow.

  14. Initial Activation and Operation of the Power Conditioning System for the National Ignition Facility

    SciTech Connect

    Newton, M A; Kamm, R E; Fulkerson, E S; Hulsey, S D; Lao, N; Parrish, G L; Pendleton, D L; Petersen, D E; Polk, M; Tuck, J M; Ullery, G T; Moore, W B

    2003-08-20

    The NIF Power Conditioning System (PCS) resides in four Capacitor Bays, supplying energy to the Master and Power Amplifiers which reside in the two adjacent laser bays. Each capacitor bay will initially house 48 individual power conditioning modules, shown in Figure 2, with space reserved for expansion to 54 modules. The National Ignition Facility (NIF) Power Conditioning System (PCS) is a modular capacitive energy storage system that will be capable of storing nearly 400 MJ of electrical energy and delivering that energy to the nearly 8000 flashlamps in the NIF laser. The first sixteen modules of the power conditioning system have been built, tested and installed. Activation of the first nine power conditioning modules has been completed and commissioning of the first ''bundle'' of laser beamlines has begun. This paper will provide an overview of the power conditioning system design and describe the status and results of initial testing and activation of the first ''bundle'' of power conditioning modules.

  15. 18 CFR 367.29 - Compensation for use of capital.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Compensation for use of capital. 367.29 Section 367.29 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... POWER ACT AND NATURAL GAS ACT UNIFORM SYSTEM OF ACCOUNTS FOR CENTRALIZED SERVICE COMPANIES SUBJECT...

  16. 18 CFR 367.29 - Compensation for use of capital.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Compensation for use of capital. 367.29 Section 367.29 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... POWER ACT AND NATURAL GAS ACT UNIFORM SYSTEM OF ACCOUNTS FOR CENTRALIZED SERVICE COMPANIES SUBJECT...

  17. 18 CFR 367.29 - Compensation for use of capital.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Compensation for use of capital. 367.29 Section 367.29 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... POWER ACT AND NATURAL GAS ACT UNIFORM SYSTEM OF ACCOUNTS FOR CENTRALIZED SERVICE COMPANIES SUBJECT...

  18. 18 CFR 367.29 - Compensation for use of capital.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Compensation for use of capital. 367.29 Section 367.29 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY... POWER ACT AND NATURAL GAS ACT UNIFORM SYSTEM OF ACCOUNTS FOR CENTRALIZED SERVICE COMPANIES SUBJECT...

  19. Perfect Optical Compensator With 1:1 Shutter Ratio Used For High Speed Camera

    NASA Astrophysics Data System (ADS)

    Zhihong, Rong

    1983-03-01

    An optical compensator used for high speed camera is described. The method of compensation, the analysis of the imaging quality and the result of experiment are introduced. The compensator consists of pairs of parallel mirrors. It can perform perfect compensation even at 1:1 shutter ratio. Using this compensator a high speed camera can be operated with no shutter and can obtain the same image sharpness as that of the intermittent camera. The advantages of this compensator are summarized as follows: . While compensating, the aberration correction of the objective would not be damaged. . There is no displacement and defocussing between the scanning image and the film in frame center during compensation. Increasing the exposure angle doesn't reduce the resolving power. . The compensator can also be used in the projector in place of the intermittent mechanism to practise continuous (non-intermittent) projection without shutter.

  20. ERC product improvement activities for direct fuel cell power plants

    SciTech Connect

    Maru, H.C.; Farooque, M.; Bentley, C.

    1995-12-01

    This program is designed to advance the carbonate fuel cell technology from the current power plant demonstration status to the commercial design in an approximately five-year period. The specific objectives which will allow attainment of the overall program goal are: (1) Define market-responsive power plant requirements and specifications, (2) Establish the design for a multifuel, low-cost, modular, market-responsive power plant, (3) Resolve power plant manufacturing issues and define the design for the commercial manufacturing facility, (4) Define the stack and BOP equipment packaging arrangement and define module designs, (5) Acquire capability to support developmental testing of stacks and BOP equipment as required to prepare for commercial design, and (6) Resolve stack and BOP equipment technology issues and design, build, and field test a modular commercial prototype power plant to demonstrate readiness for commercial entry. A seven-task program, dedicated to attaining objective(s) in the areas noted above, was initiated in December 1994. Accomplishments of the first six months are discussed in this paper.

  1. ERC product improvement activities for direct fuel cell power plants

    SciTech Connect

    Bentley, C.; Carlson, G.; Doyon, J.

    1995-08-01

    This program is designed to advance the carbonate fuel cell technology from the current power plant demonstration status to the commercial design in an approximately five-year period. The specific objectives which will allow attainment of the overall program goal are: (1) Define market-responsive power plant requirements and specifications, (2) Establish the design for a multifuel, low-cost, modular, market-responsive power plant, (3) Resolve power plant manufacturing issues and define the design for the commercial manufacturing facility, (4) Define the stack and BOP equipment packaging arrangement and define module designs, (5) Acquire capability to support developmental testing of stacks and BOP equipment as required to prepare for commercial design, and (6) Resolve stack and BOP equipment technology issues and design, build, and field test a modular commercial prototype power plant to demonstrate readiness for commercial entry. A seven-task program, dedicated to attaining objective(s) in the areas noted above, was initiated in December 1994. Accomplishments of the first six months are discussed in this paper.

  2. Deferred Compensation Becomes More Common

    ERIC Educational Resources Information Center

    June, Audrey Williams

    2006-01-01

    A key part of the compensation package for some college and university presidents is money that they do not receive in their paychecks. Formally known as deferred compensation, such payments can take many forms, including supplemental retirement pay, severance pay, or even bonuses. With large institutions leading the way, deferred compensation has…

  3. The Federal Employees' Compensation Act.

    ERIC Educational Resources Information Center

    Nordlund, Willis J.

    1991-01-01

    The 1916 Federal Employees' Compensation Act is still the focal point around which the federal workers compensation program works today. The program has gone through many changes on its way to becoming a modern means of compensating workers for job-related injury, disease, and death. (Author)

  4. CGI delay compensation

    NASA Technical Reports Server (NTRS)

    Mcfarland, Richard E.

    1986-01-01

    Computer-generated graphics in real-time helicopter simulation produces objectionable scene-presentation time delays. In the flight simulation laboratory at Ames Research Center, it has been determined that these delays have an adverse influence on pilot performance during aggressive tasks such as nap-of-the-earth (NOE) maneuvers. Using contemporary equipment, computer-generated image (CGI) time delays are an unavoidable consequence of the operations required for scene generation. However, providing that magnitide distortions at higher frequencies are tolerable, delay compensation is possible over a restricted frequency range. This range, assumed to have an upper limit of perhaps 10 or 15 rad/sec, conforms approximately to the bandwidth associated with helicopter handling qualities research. A compensation algorithm is introduced here and evaluated in terms of tradeoffs in frequency responses. The algorithm has a discrete basis and accommodates both a large, constant transport delay interval and a periodic delay interval, as associated with asynchronous operations.

  5. Ground difference compensating system

    DOEpatents

    Johnson, Kris W.; Akasam, Sivaprasad

    2005-10-25

    A method of ground level compensation includes measuring a voltage of at least one signal with respect to a primary ground potential and measuring, with respect to the primary ground potential, a voltage level associated with a secondary ground potential. A difference between the voltage level associated with the secondary ground potential and an expected value is calculated. The measured voltage of the at least one signal is adjusted by an amount corresponding to the calculated difference.

  6. Fibre-coupled multiphoton microscope with adaptive motion compensation

    PubMed Central

    Sherlock, Ben; Warren, Sean; Stone, James; Neil, Mark; Paterson, Carl; Knight, Jonathan; French, Paul; Dunsby, Chris

    2015-01-01

    To address the challenge of sample motion during in vivo imaging, we present a fibre-coupled multiphoton microscope with active axial motion compensation. The position of the sample surface is measured using optical coherence tomography and fed back to a piezo actuator that adjusts the axial location of the objective to compensate for sample motion. We characterise the system’s performance and demonstrate that it can compensate for axial sample velocities up to 700 µm/s. Finally we illustrate the impact of motion compensation when imaging multiphoton excited autofluorescence in ex vivo mouse skin. PMID:26137387

  7. Unified active and reactive power modulation of HVDC transmission systems

    NASA Astrophysics Data System (ADS)

    Grund, C. E.; Pohl, R. V.

    1981-11-01

    The power modulation of a high voltage direct current (HVDC) system for stabilization of an ac/dc network was investigated. It was found that simultaneous modulation of both dc current and voltage was more effective than just current modulation by itself, since the dc voltage modulation could be used to minimize the reactive power changes resulting from a change of the dc current. This helps stabilize the ac busbar voltages at the converters, which reduces undesirable load flow changes to voltage dependent ac loads, thus improving the effectiveness of the dc power modulation. This unified modulation control concept was evaluated by means of digital computer studies as well as a special purpose HVDC simulator. Several combined ac/dc power transmission systems were synthesized for testing of different modulation controller concepts. An optimum controller design incorporating a linear quadratic control algorithm with full state feedback was first studied. This provided a basis for comparison of suboptimal controller designs utilizing reduced state feedback and a Kalman filter state reconstruction technique.

  8. Favorite Lesson Plans: Powerful Standards-Based Activities.

    ERIC Educational Resources Information Center

    Wilen, William W., Ed.

    This collection of lesson plans helps social studies teachers and teacher educators implement the various national and state standards in their classrooms. The collection illustrates how classroom implementation can be achieved through the application of the powerful teaching and learning principles devised by National Council for the Social…

  9. 12 CFR 550.390 - May my officer or employee retain compensation for acting as a co-fiduciary?

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 5 2010-01-01 2010-01-01 false May my officer or employee retain compensation..., DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.390 May my officer or employee retain compensation for acting as a...

  10. 12 CFR 550.390 - May my officer or employee retain compensation for acting as a co-fiduciary?

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 6 2013-01-01 2012-01-01 true May my officer or employee retain compensation..., DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.390 May my officer or employee retain compensation for acting as a...

  11. 12 CFR 550.390 - May my officer or employee retain compensation for acting as a co-fiduciary?

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 6 2014-01-01 2012-01-01 true May my officer or employee retain compensation..., DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.390 May my officer or employee retain compensation for acting as a...

  12. 12 CFR 550.390 - May my officer or employee retain compensation for acting as a co-fiduciary?

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 5 2011-01-01 2011-01-01 false May my officer or employee retain compensation..., DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.390 May my officer or employee retain compensation for acting as a...

  13. 12 CFR 550.390 - May my officer or employee retain compensation for acting as a co-fiduciary?

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 6 2012-01-01 2012-01-01 false May my officer or employee retain compensation..., DEPARTMENT OF THE TREASURY FIDUCIARY POWERS OF SAVINGS ASSOCIATIONS Exercising Fiduciary Powers Compensation, Gifts, and Bequests § 550.390 May my officer or employee retain compensation for acting as a...

  14. 29 CFR 36.515 - Compensation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or... that, on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results...

  15. Compensation of Certified Health Education Specialists

    ERIC Educational Resources Information Center

    Bonaguro, John; White, John; Duncan, David F.; Nicholson, Thomas; Smith, Becky J.

    2009-01-01

    Health education moved toward professionalization with the establishment, in 1988, of the National Commission for Health Education Credentialing, Inc. Today, there are approximately 8,000 active holders of the CHES credential. This article examines the compensation levels of CHES recipients in relation to their current position, employment setting…

  16. 29 CFR 36.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or... that, on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results...

  17. 29 CFR 36.515 - Compensation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Secretary of Labor NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or... that, on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results...

  18. 10 CFR 5.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... REGULATORY COMMISSION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or..., on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results in...

  19. 38 CFR 23.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Compensation. 23.515 Section 23.515 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED) NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex...

  20. 45 CFR 2555.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 4 2011-10-01 2011-10-01 false Compensation. 2555.515 Section 2555.515 Public Welfare Regulations Relating to Public Welfare (Continued) CORPORATION FOR NATIONAL AND COMMUNITY SERVICE NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of...

  1. 40 CFR 5.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Compensation. 5.515 Section 5.515 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs...

  2. 22 CFR 229.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Compensation. 229.515 Section 229.515 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or...

  3. 15 CFR 8a.515 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Compensation. 8a.515 Section 8a.515 Commerce and Foreign Trade Office of the Secretary of Commerce NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs...

  4. 34 CFR 106.54 - Compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 34 Education 1 2011-07-01 2011-07-01 false Compensation. 106.54 Section 106.54 Education Regulations of the Offices of the Department of Education OFFICE FOR CIVIL RIGHTS, DEPARTMENT OF EDUCATION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex...

  5. 10 CFR 5.515 - Compensation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATORY COMMISSION NONDISCRIMINATION ON THE BASIS OF SEX IN EDUCATION PROGRAMS OR ACTIVITIES RECEIVING FEDERAL FINANCIAL ASSISTANCE Discrimination on the Basis of Sex in Employment in Education Programs or..., on the basis of sex: (a) Makes distinctions in rates of pay or other compensation; (b) Results in...

  6. Diderot Reconsidered: Visual Impairment and Auditory Compensation.

    ERIC Educational Resources Information Center

    Miller, L.

    1992-01-01

    This paper reviews two models for auditory compensation attending visual loss--structural and strategic. The paper concludes that it is not clear to what extent differences in auditory processing represent variations in underlying capacity, the development of strategies, attentional activation, or multiple factors. Previous dismissals of…

  7. Forest Ecosystem Services and Eco-Compensation Mechanisms in China

    NASA Astrophysics Data System (ADS)

    Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

    2011-12-01

    Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

  8. Forest ecosystem services and eco-compensation mechanisms in China.

    PubMed

    Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

    2011-12-01

    Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence. PMID:21882001

  9. The impact of materials selection on long-term activation in fusion power plants

    NASA Astrophysics Data System (ADS)

    Taylor, N. P.; Forty, C. B. A.; Petti, D. A.; McCarthy, K. A.

    2000-12-01

    Neutron-induced transmutation of materials in a D-T fusion power plant will give rise to the potential for long-term activation. To ensure that the attractive safety and environmental characteristics of fusion power are not degraded, careful design choices are necessary. An aim of optimising power plant design must be to minimise both the level of activation and the total volume of active material that might ultimately be categorised as waste requiring disposal. Materials selection is central to this optimisation. In this paper we assess the influence of materials choices for a power plant on the waste volume and the potential to clear (i.e. remove from regulatory control) and recycle material. Although the use of low activation materials in regions of high neutron flux is an important part of the strategy to minimise the level of activation, different choices may result from a strategy aimed at minimising the volume of active waste.

  10. Cooperative Control of Active Power Filters in Power Systems without Mutual Communication

    DOE PAGESBeta

    Tlustý, Josef; Škramlík, Jiří; Švec, Jan; Valouch, Viktor

    2010-01-01

    The procedure for calculating controller parameters of the APFs implemented into a multibus industrial power system for harmonic voltage mitigation is presented. The node-voltage-detection control strategy is applied and the basic controller parameters are found under the condition that the demanded THD factors at the buses where the APFs are placed will be obtained. A cooperative control of several APFs without mutual communication is proposed, simulated, and experimentally verified. By tuning the controller gains without considering the power circuit parameters, all APFs used tend to share harmonic load currents approximately equally regardless of the operation modes of the nonlinear loadsmore » in different parts of the power system.« less

  11. Temperature compensation and entrainment in circadian rhythms

    NASA Astrophysics Data System (ADS)

    Bodenstein, C.; Heiland, I.; Schuster, S.

    2012-06-01

    To anticipate daily variations in the environment and coordinate biological activities into a daily cycle many organisms possess a circadian clock. In the absence of external time cues the circadian rhythm persists with a period of approximately 24 h. The clock phase can be shifted by single pulses of light, darkness, chemicals, or temperature and this allows entrainment of the clock to exactly 24 h by cycles of these zeitgebers. On the other hand, the period of the circadian rhythm is kept relatively constant within a physiological range of constant temperatures, which means that the oscillator is temperature compensated. The mechanisms behind temperature compensation and temperature entrainment are not fully understood, neither biochemically nor mathematically. Here, we theoretically investigate the interplay of temperature compensation and entrainment in general oscillatory systems. We first give an analytical treatment for small temperature shifts and derive that every temperature-compensated oscillator is entrainable to external small-amplitude temperature cycles. Temperature compensation ensures that this entrainment region is always centered at the endogenous period regardless of possible seasonal temperature differences. Moreover, for small temperature cycles the entrainment region of the oscillator is potentially larger for rectangular pulses. For large temperature shifts we numerically analyze different circadian clock models proposed in the literature with respect to these properties. We observe that for such large temperature shifts sinusoidal or gradual temperature cycles allow a larger entrainment region than rectangular cycles.

  12. Natural Killer Cell Sensing of Infected Cells Compensates for MyD88 Deficiency but Not IFN-I Activity in Resistance to Mouse Cytomegalovirus.

    PubMed

    Cocita, Clément; Guiton, Rachel; Bessou, Gilles; Chasson, Lionel; Boyron, Marilyn; Crozat, Karine; Dalod, Marc

    2015-05-01

    In mice, plasmacytoid dendritic cells (pDC) and natural killer (NK) cells both contribute to resistance to systemic infections with herpes viruses including mouse Cytomegalovirus (MCMV). pDCs are the major source of type I IFN (IFN-I) during MCMV infection. This response requires pDC-intrinsic MyD88-dependent signaling by Toll-Like Receptors 7 and 9. Provided that they express appropriate recognition receptors such as Ly49H, NK cells can directly sense and kill MCMV-infected cells. The loss of any one of these responses increases susceptibility to infection. However, the relative importance of these antiviral immune responses and how they are related remain unclear. In humans, while IFN-I responses are essential, MyD88 is dispensable for antiviral immunity. Hence, a higher redundancy has been proposed in the mechanisms promoting protective immune responses against systemic infections by herpes viruses during natural infections in humans. It has been assumed, but not proven, that mice fail to mount protective MyD88-independent IFN-I responses. In humans, the mechanism that compensates MyD88 deficiency has not been elucidated. To address these issues, we compared resistance to MCMV infection and immune responses between mouse strains deficient for MyD88, the IFN-I receptor and/or Ly49H. We show that selective depletion of pDC or genetic deficiencies for MyD88 or TLR9 drastically decreased production of IFN-I, but not the protective antiviral responses. Moreover, MyD88, but not IFN-I receptor, deficiency could largely be compensated by Ly49H-mediated antiviral NK cell responses. Thus, contrary to the current dogma but consistent with the situation in humans, we conclude that, in mice, in our experimental settings, MyD88 is redundant for IFN-I responses and overall defense against a systemic herpes virus infection. Moreover, we identified direct NK cell sensing of infected cells as one mechanism able to compensate for MyD88 deficiency in mice. Similar mechanisms likely

  13. Austin, Texas: An Educator/Business Collaboration in Support of Teacher Compensation Reform. Teacher Compensation and Teacher Quality: Policy Brief

    ERIC Educational Resources Information Center

    Committee for Economic Development, 2013

    2013-01-01

    In its 2009 report "Teacher Compensation and Teacher Quality," the Committee for Economic Development urged business leaders to be active participants in school district deliberations about teacher compensation policies. The Committee for Economic Development (CED) noted that "business leaders can make the case to the public that current policies…

  14. Entrainment in solution of an oscillating NADH oxidase activity from the bovine milk fat globule membrane with a temperature-compensated period length suggestive of an ultradian time-keeping (clock) function

    NASA Technical Reports Server (NTRS)

    Morre, D. James; Lawler, Juliana; Wang, Sui; Keenan, Thomas W.; Morre, Dorothy M.

    2002-01-01

    Entrainment in solution of an oscillating activity with a temperature compensated period of 24 min is described for a NADH oxidase (NOX) activity of the bovine milk fat globule membrane, a derivative of the mammary epithelial cell plasma membrane. The period of 24 min remained unchanged at 17 degrees C, 27 degrees C and 37 degrees C whereas the amplitude approximately doubled with each 10 degree C rise in temperature (Q(10)congruent with 2). The periodicity was observed with both intact milk fat globule membranes and with detergent-solubilized membranes, demonstrating that the oscillations did not require an association with membranes. The periodicity was not the result of instrument variation or of chemical interactions among reactants in solution. Preparations with different periodicities entrained (autosynchronized) when mixed. Upon mixing, the preparations exhibited two oscillatory patterns but eventually a single pattern representing the mean of the farthest separated maxima of the two preparations analyzed separately emerged. The cell surface NOX protein is the first reported example of an entrainable biochemical entity with a temperature-compensated periodicity potentially capable of functioning as an ultradian or circadian clock driver.

  15. The calcium release-activated calcium channel Orai1 represents a crucial component in hypertrophic compensation and the development of dilated cardiomyopathy.

    PubMed

    Horton, Jaime S; Buckley, Cadie L; Alvarez, Ernest M; Schorlemmer, Anita; Stokes, Alexander J

    2014-01-01

    As exceptionally calcium selective store-operated channels, Orai channels play a prominent role in cellular calcium signaling. While most studied in the immune system, we are beginning to recognize that Orai1 provides unique calcium signaling pathways in numerous tissue contexts. To assess the involvement of Orai1 in cardiac hypertrophy we used transverse aortic constriction to model pressure overload cardiac hypertrophy and heart failure in Orai1 deficient mice. We demonstrate that Orai1 deficient mice have significantly decreased survival in this pressure overload model. Transthoracic echocardiography reveals that Orai1 deficient mice develop rapid dilated cardiomyopathy, with greater loss of function, and histological and molecular data indicate that this pathology is associated with significant apoptosis, but not major differences in cellular hypertrophy, fibrosis, and some major hypertrophic makers. Orai1 represents a crucial calcium entry mechanism in the compensation of the heart to pressure overload over-load, and the development of dilated cardiomyopathy. PMID:24135962

  16. The calcium release-activated calcium channel Orai1 represents a crucial component in hypertrophic compensation and the development of dilated cardiomyopathy

    PubMed Central

    Horton, Jaime S; Buckley, Cadie L; Alvarez, Ernest M; Schorlemmer, Anita; Stokes, Alexander J

    2014-01-01

    As exceptionally calcium selective store-operated channels, Orai channels play a prominent role in cellular calcium signaling. While most studied in the immune system, we are beginning to recognize that Orai1 provides unique calcium signaling pathways in numerous tissue contexts. To assess the involvement of Orai1 in cardiac hypertrophy we used transverse aortic constriction to model pressure overload cardiac hypertrophy and heart failure in Orai1 deficient mice. We demonstrate that Orai1 deficient mice have significantly decreased survival in this pressure overload model. Transthoracic echocardiography reveals that Orai1 deficient mice develop rapid dilated cardiomyopathy, with greater loss of function, and histological and molecular data indicate that this pathology is associated with significant apoptosis, but not major differences in cellular hypertrophy, fibrosis, and some major hypertrophic makers. Orai1 represents a crucial calcium entry mechanism in the compensation of the heart to pressure overload over-load, and the development of dilated cardiomyopathy. PMID:24135962

  17. Laboratory atmospheric compensation experiment

    NASA Astrophysics Data System (ADS)

    Drutman, C.; Moran, James P.; Faria-e-Maia, Francisco; Hyman, Howard; Russell, Jeffrey A.

    1993-06-01

    This paper describes an in-house experiment that was performed at the Avco Research Labs/Textron to test a proprietary atmospheric phase compensation algorithm. Since the laser energies of interest were small enough that thermal blooming was not an issue, it was only necessary to simulate the effect of atmospheric turbulence. This was achieved by fabricating phase screens that mimicked Kolmogorov phase statistics. A simulated atmosphere was constructed from these phase screens and the phase at the simulated ground was measured with a digital heterodyne interferometer. The result of this effort was an initial verification of our proprietary algorithm two years before the field experiment.

  18. Power-gated 32 bit microprocessor with a power controller circuit activated by deep-sleep-mode instruction achieving ultra-low power operation

    NASA Astrophysics Data System (ADS)

    Koike, Hiroki; Ohsawa, Takashi; Miura, Sadahiko; Honjo, Hiroaki; Ikeda, Shoji; Hanyu, Takahiro; Ohno, Hideo; Endoh, Tetsuo

    2015-04-01

    A spintronic-based power-gated micro-processing unit (MPU) is proposed. It includes a power control circuit activated by the newly supported power-off instruction for the deep-sleep mode. These means enable the power-off procedure for the MPU to be executed appropriately. A test chip was designed and fabricated using 90 nm CMOS and an additional 100 nm MTJ process; it was successfully operated. The guideline of the energy reduction effects for this MPU was presented, using the estimation based on the measurement results of the test chip. The result shows that a large operation energy reduction of 1/28 can be achieved when the operation duty is 10%, under the condition of a sufficient number of idle clock cycles.

  19. Operation of the power information center: Performance of secretariat functions and information exchange activities in the advanced power field of the interagency advanced power group

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Highlights of activities conducted during the reporting period to facilitate the exchange of technical information among scientists and engineers both within the federal government and within industry are cited. Interagency Advanced Power Group meetings and special efforts, project briefs, and organization development are considered.

  20. Smart Moves: Powering up the Brain with Physical Activity

    ERIC Educational Resources Information Center

    Conyers, Marcus; Wilson, Donna

    2015-01-01

    The Common Core State Standards emphasize higher-order thinking, problem solving, and the creation, retention, and application of knowledge. Achieving these standards creates greater cognitive demands on students. Recent research suggests that active play and regular exercise have a positive effect on brain regions associated with executive…

  1. Radiation-induced attenuation self-compensating effect in super-fluorescent fiber source

    NASA Astrophysics Data System (ADS)

    Yang, Yuan-Hong; Suo, Xin-Xin; Yang, Wei

    2014-09-01

    The compact super-fluorescent fiber source (SFS) output spectra variations at different pump currents and under different dose of gamma-ray radiation were measured and compared respectively. The radiation-induced attenuation (RIA) self-compensating effect in SFS based on photo-bleaching was found and the general mathematic model of SFS output spectra variations was made. The radiation-induced background attenuation (RIBA) at the pump wavelength was identified to be the main cause of the total output power and spectra variations and the variations can then be compensated by active control of the pump power to enhance the self-compensating effect. With closed-loop feedback control of pump current, double-pass backward (DPB) configuration and spectrum re-shaping technology, an SFS prototype was made and tested. The mean-wavelength stability of about 87.4 ppm and output power instability of less than 5% were achieved under up to 200 krad (Si) gamma-ray irradiation.

  2. "Power, Regulation and Physically Active Identities": The Experiences of Rural and Regional Living Adolescent Girls

    ERIC Educational Resources Information Center

    Casey, M.; Mooney, A.; Smyth, J.; Payne, W.

    2016-01-01

    Drawing on interpretations of Foucault's techniques of power, we explored the discourses and power relations operative between groups of girls that appeared to influence their participation in Physical Education (PE) and outside of school in sport and physical activity (PA) in rural and regional communities. Interviews and focus groups were…

  3. Machine Shop I. Learning Activity Packets (LAPs). Section D--Power Saws and Drilling Machines.

    ERIC Educational Resources Information Center

    Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

    This document contains two learning activity packets (LAPs) for the "power saws and drilling machines" instructional area of a Machine Shop I course. The two LAPs cover the following topics: power saws and drill press. Each LAP contains a cover sheet that describes its purpose, an introduction, and the tasks included in the LAP; learning steps…

  4. Extrathermodynamics: Varieties of Compensation Effect.

    PubMed

    Khakhel', Oleg A; Romashko, Tamila P

    2016-03-31

    There are several types of the ΔH compensation. Along with well-known phenomenon of the ΔH - ΔS compensation, two more types of the ΔH - (ΔS + RΔ ln Ω) compensation are observed in some series of systems. The nature of these phenomena is connected with the behavior of phase volume of systems, Ω. The role of other thermodynamic parameters, which describe series in manifestation of this or that types of the ΔH compensation, is shown in light of molecular statistical mechanics. PMID:26949977

  5. 78 FR 8493 - Foreign-Trade Zone 45-Portland, OR; Notification of Proposed Production Activity; SoloPower Inc...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-06

    ... Activity; SoloPower Inc. (Thin Film Photovoltaic Solar Panels); Portland, OR SoloPower Inc. (SoloPower) has... January 28, 2013. The SoloPower facility is located within Site 1 of FTZ 45. The facility is used for the production of thin film photovoltaic solar panels. Pursuant to 15 CFR 400.14(b), FTZ activity would...

  6. Radio-frequency spectroscopy of the active fiber heating under condition of high-power lasing generation.

    PubMed

    Ryabushkin, O A; Shaidullin, R I; Zaytsev, I A

    2015-05-01

    A novel method for the precise temperature measurement of active fibers in high-power fiber lasers and amplifiers is introduced. This method allows the determination of active fiber longitudinal temperature distribution at different optical pump powers. PMID:25927761

  7. Rain compensation algorithm for ACTS mobile terminal

    NASA Technical Reports Server (NTRS)

    Levitt, Barry K.

    1992-01-01

    The initial advanced communication technology satellite (ACTS) mobile terminal (AMT) demonstrations will involve two-way communications between the high-bit-rate link evaluation terminal (HBR-LET), which is a fixed terminal (FT), and a van-housed mobile terminal (MT). The HBR-LET has the capability of adjusting its transmitted uplink power over an approximately 10-dB range to compensate for forward uplink rain attenuation. However, because of size and weight limitations, the MT cannot use power control as a rain compensation technique. Consequently, the AMT rain compensation algorithm (RCA) is based on a formula for varying the transmitted data rate in either direction to maintain link performance within acceptable limits. The objective of the AMT RCA is to ensure reliable operation in both the forward and return directions despite the possibility of uplink or downlink fading due to rain events in the vicinity of the FT or MT. In particular, the RCA must maintain at least a 3-dB link margin at the highest possible transmission rate (AMT can operate at 9.6, 4.8, or 2.4 kb/s) permitted by the prevailing channel conditions. The 3-dB minimum link margin is a system design safety factor to accommodate conceivable implementation losses.

  8. Summing pressure compensation control

    SciTech Connect

    Myers, H.A.

    1988-04-26

    This patent describes a summing pressure compensator control for hydraulic loads with at least one of the hydraulic loads being a variable displacement motor having servo means for controlling the displacement thereof, first hydraulic means responsive to the supply of fluid to the variable displacement motor to provide a first pressure signal, second hydraulic means responsive to the supply of fluid to a second hydraulic load to provide a second pressure signal, summing means for receiving the first and second pressure signals and providing a control signal proportional to the sum of the first and second pressure signals, the control signal being applied to the servo means to increase the displacement of the variable displacement motor.

  9. Compensating for thalamocortical synaptic loss in Alzheimer's disease

    PubMed Central

    Abuhassan, Kamal; Coyle, Damien; Maguire, Liam

    2014-01-01

    The study presents a thalamocortical network model which oscillates within the alpha frequency band (8–13 Hz) as recorded in the wakeful relaxed state with closed eyes to study the neural causes of abnormal oscillatory activity in Alzheimer's disease (AD). Incorporated within the model are various types of cortical excitatory and inhibitory neurons, recurrently connected to thalamic and reticular thalamic regions with the ratios and distances derived from the mammalian thalamocortical system. The model is utilized to study the impacts of four types of connectivity loss on the model's spectral dynamics. The study focuses on investigating degeneration of corticocortical, thalamocortical, corticothalamic, and corticoreticular couplings, with an emphasis on the influence of each modeled case on the spectral output of the model. Synaptic compensation has been included in each model to examine the interplay between synaptic deletion and compensation mechanisms, and the oscillatory activity of the network. The results of power spectra and event related desynchronization/synchronization (ERD/S) analyses show that the dynamics of the thalamic and cortical oscillations are significantly influenced by corticocortical synaptic loss. Interestingly, the patterns of changes in thalamic spectral activity are correlated with those in the cortical model. Similarly, the thalamic oscillatory activity is diminished after partial corticothalamic denervation. The results suggest that thalamic atrophy is a secondary pathology to cortical shrinkage in Alzheimer's disease. In addition, this study finds that the inhibition from neurons in the thalamic reticular nucleus (RTN) to thalamic relay (TCR) neurons plays a key role in regulating thalamic oscillations; disinhibition disrupts thalamic oscillatory activity even though TCR neurons are more depolarized after being released from RTN inhibition. This study provides information that can be explored experimentally to further our

  10. Implementation of FFT Algorithm using DSP TMS320F28335 for Shunt Active Power Filter

    NASA Astrophysics Data System (ADS)

    Patel, Pinkal Jashvantbhai; Patel, Rajesh M.; Patel, Vinod

    2016-07-01

    This work presents simulation, analysis and experimental verification of Fast Fourier Transform (FFT) algorithm for shunt active power filter based on three-level inverter. Different types of filters can be used for elimination of harmonics in the power system. In this work, FFT algorithm for reference current generation is discussed. FFT control algorithm is verified using PSIM simulation results with DLL block and C-code. Simulation results are compared with experimental results for FFT algorithm using DSP TMS320F28335 for shunt active power filter application.

  11. 77 FR 326 - Agency Information Collection (Application for Dependency and Indemnity Compensation By Parent(s...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-04

    ...), (Including Accrued Benefits and Death Compensation)): Activity Under OMB Review AGENCY: Veterans Benefits... Dependency and Indemnity Compensation by Parent(s), (Including Accrued Benefits and Death Compensation), VA... collection. Abstract: Surviving parent(s) of veterans whose death was service connected complete VA Form...

  12. Quasi-optical solid-state power combining for millimeter-wave active seeker applications

    NASA Astrophysics Data System (ADS)

    Halladay, R. H.; Terrill, S. D.; Bowling, D. R.; Gagnon, D. R.

    1992-05-01

    Consideration is given to quasi-optical power combining techniques, state-of-the-art demonstrated performance, and system issues as they apply to endoatmospheric homing seeker insertion. Quasi-optical power combining is based on combining microwave and millimeter-wave solid-state device power in space through the use of antennas and lenses. It is concluded that quasi-optical power combining meets the severe electrical requirements and packaging constraints of active MMW seekers for endoatmospheric hit-to-kill missiles. The approach provides the possibility of wafer-scale integration of major components for low cost production and offers high reliability. Critical issues include thermal loading and system integration, which must be resolved before the quasi-optical power combining technology will be applied to an active MMW seeker.

  13. Quasi-optical solid-state power combining for millimeter-wave active seeker applications

    SciTech Connect

    Halladay, R.H.; Terrill, S.D.; Bowling, D.R.; Gagnon, D.R. U.S. Navy, Naval Air Warfare Center, China Lake, CA )

    1992-05-01

    Consideration is given to quasi-optical power combining techniques, state-of-the-art demonstrated performance, and system issues as they apply to endoatmospheric homing seeker insertion. Quasi-optical power combining is based on combining microwave and millimeter-wave solid-state device power in space through the use of antennas and lenses. It is concluded that quasi-optical power combining meets the severe electrical requirements and packaging constraints of active MMW seekers for endoatmospheric hit-to-kill missiles. The approach provides the possibility of wafer-scale integration of major components for low cost production and offers high reliability. Critical issues include thermal loading and system integration, which must be resolved before the quasi-optical power combining technology will be applied to an active MMW seeker. 18 refs.

  14. Load positioning system with gravity compensation

    NASA Technical Reports Server (NTRS)

    Hollow, R. H.

    1984-01-01

    A load positioning system with gravity compensation has a servomotor, position sensing feedback potentiometer and velocity sensing tachometer in a conventional closed loop servo arrangement to cause a lead screw and a ball nut to vertically position a load. Gravity compensating components comprise the DC motor, gears, which couple torque from the motor to the lead screw, and constant current power supply. The constant weight of the load applied to the lead screw via the ball nut tend to cause the lead screw to rotate, the constant torque of which is opposed by the constant torque produced by the motor when fed from the constant current source. The constant current is preset as required by the potentiometer to effect equilibration of the load which thereby enables the positioning servomotor to see the load as weightless under both static and dynamic conditions. Positioning acceleration and velocity performance are therefore symmetrical.

  15. Manufacture of magnetically active fiber-reinforced composites for use in power generation

    NASA Astrophysics Data System (ADS)

    Etches, Julie; Bond, Ian; Mellor, Phil

    2004-07-01

    A major issue yet to be resolved for embedding sensors, actuators and microelectromechanical systems (MEMS) in 'smart' structures is that of providing power. Work is ongoing in the field with examples of micro battery technology, use of solar power and micro fuel cells. The work presented here considers a technology to enable the development of integrated power generation and actuation. Magnetic fibre reinforced composite material has been developed which utilises hollow glass fibres filled with active magnetic material. The resulting material maintains structural integrity as well as providing a possible means of electrical power generation from a dynamically loaded structure. The hollow glass fibres were manufactured in-house using a bespoke fibre drawing facility. Hard magnetic powder materials were introduced into the hollow fibre cores to provide an active electromagnetic function. This paper will discuss the manufacture, characterization and optimisation of active magnetic fibre reinforced composite materials.

  16. An embryonic myosin converter domain influences Drosophila indirect flight muscle stretch activation, power generation and flight

    PubMed Central

    Wang, Qian; Newhard, Christopher S.; Ramanath, Seemanti; Sheppard, Debra; Swank, Douglas M.

    2014-01-01

    Stretch activation (SA) is critical to the flight ability of insects powered by asynchronous, indirect flight muscles (IFMs). An essential muscle protein component for SA and power generation is myosin. Which structural domains of myosin are significant for setting SA properties and power generation levels is poorly understood. We made use of the transgenic techniques and unique single muscle myosin heavy chain gene of Drosophila to test the influence of the myosin converter domain on IFM SA and power generation. Replacing the endogenous converter with an embryonic version decreased SA tension and the rate of SA tension generation. The alterations in SA properties and myosin kinetics from the converter exchange caused power generation to drop to 10% of control fiber power when the optimal conditions for control fibers – 1% muscle length (ML) amplitude and 150 Hz oscillation frequency – were applied to fibers expressing the embryonic converter (IFI-EC). Optimizing conditions for IFI-EC fiber power production, by doubling ML amplitude and decreasing oscillation frequency by 60%, improved power output to 60% of optimized control fiber power. IFI-EC flies altered their aerodynamic flight characteristics to better match optimal fiber power generation conditions as wing beat frequency decreased and wing stroke amplitude increased. This enabled flight in spite of the drastic changes to fiber mechanical performance. PMID:24115062

  17. Primary-care physician compensation.

    PubMed

    Olson, Arik

    2012-01-01

    This article reviews existing models of physician compensation and presents information about current compensation patterns for primary-care physicians in the United States. Theories of work motivation are reviewed where they have relevance to the desired outcome of satisfied, productive physicians whose skills and expertise are retained in the workforce. Healthcare reforms that purport to bring accountability for healthcare quality and value-rather than simply volume-bring opportunities to redesign primary-care physician compensation and may allow for new compensation methodologies that increase job satisfaction. Physicians are increasingly shunning the responsibility of private practice and choosing to work as employees of a larger organization, often a hospital. Employers of physicians are seeking compensation models that reward both productivity and value. PMID:22786738

  18. 38 CFR 3.4 - Compensation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2013-07-01 2013-07-01 false Compensation. 3.4 Section 3.4 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation General § 3.4 Compensation. (a) Compensation. This term means a monthly payment made by...

  19. A Curriculum Activities Guide to Electric Power Generation and the Environment.

    ERIC Educational Resources Information Center

    Tully, Randolph R., Jr., Ed.

    This guide was developed by teachers involved in a workshop on "Electric Power Generation and the Environment." Activity topics are: (1) Energy and the Consumer; (2) Energy and Water Pollution; and (3) Energy and Air Pollution. Within these topics, the activities are classified as awareness level, transitional level, or operational level. Each…

  20. A performance comparison of static VAr compensator based on Goertzel and FFT algorithm and experimental validation.

    PubMed

    Kececioglu, O Fatih; Gani, Ahmet; Sekkeli, Mustafa

    2016-01-01

    The main objective of the present paper is to introduce a new approach for measuring and calculation of fundamental power components in the case of various distorted waveforms including those containing harmonics. The parameters of active, reactive, apparent power and power factor, are measured and calculated by using Goertzel algorithm instead of fast Fourier transformation which is commonly used. The main advantage of utilizing Goertzel algorithm is to minimize computational load and trigonometric equations. The parameters measured in the new technique are applied to a fixed capacitor-thyristor controlled reactor based static VAr compensation system to achieve accurate power factor correction for the first time. This study is implemented both simulation and experimentally. PMID:27047717

  1. The effects of bicycle frame geometry on muscle activation and power during a wingate anaerobic test.

    PubMed

    Ricard, Mark D; Hills-Meyer, Patrick; Miller, Michael G; Michael, Timothy J

    2006-01-01

    The purpose of this study was to compare the effects of bicycle seat tube angles (STA) of (72° and 82°) on power production and EMG of the vastus laeralis (VL), vastus medialis (VM), semimembranous (SM), biceps femoris (BF) during a Wingate test (WAT). Twelve experienced cyclists performed a WAT at each STA. Repeated measures ANOVA was used to identify differences in muscular activation by STA. EMG variables were normalized to isometric maximum voluntary contraction (MVC). Paired t-tests were used to test the effects of STA on: peak power, average power, minimum power and percent power drop. Results indicated BF activation was significantly lower at STA 82° (482.9 ± 166.6 %MVC·s) compared to STA 72° (712.6 ± 265.6 %MVC·s). There were no differences in the power variables between STAs. The primary finding was that increasing the STA from 72° to 82° enabled triathletes' to maintain power production, while significantly reducing the muscular activation of the biceps femoris muscle. Key PointsRoad cyclists claim that bicycle seat tube angles between 72° and 76° are most effective for optimal performance in racing.Triathletes typically use seat tube angles greater than 76°. It is thought that a seat tube angle greater than 76° facilitates a smoother bike to run transition in the triathlon.Increasing the seat tube angle from 72 to 82 enabled triathletes' to maintain power production, while significantly reducing the muscular activation of the biceps femoris muscle.Reduced hamstring muscular activation in the triathlon frame (82 seat tube angle) may serve to reduce hamstring tightness following the bike phase of the triathlon, allowing the runner to use a longer stride length. PMID:24198678

  2. [Vestibular compensation studies]. [Vestibular Compensation and Morphological Studies

    NASA Technical Reports Server (NTRS)

    Perachio, Adrian A. (Principal Investigator)

    1996-01-01

    The following topics are reported: neurophysiological studies on MVN neurons during vestibular compensation; effects of spinal cord lesions on VNC neurons during compensation; a closed-loop vestibular compensation model for horizontally canal-related MVN neurons; spatiotemporal convergence in VNC neurons; contributions of irregularly firing vestibular afferents to linear and angular VOR's; application to flight studies; metabolic measures in vestibular neurons; immediate early gene expression following vestibular stimulation; morphological studies on primary afferents, central vestibular pathways, vestibular efferent projection to the vestibular end organs, and three-dimensional morphometry and imaging.

  3. Convection Compensated Electrophoretic NMR

    NASA Astrophysics Data System (ADS)

    He, Qiuhong; Wei, Zhaohui

    2001-06-01

    A novel method of convection compensated ENMR (CC-ENMR) has been developed to detect electrophoretic motion of ionic species in the presence of bulk solution convection. This was accomplished using a gradient moment nulling technique to remove spectral artifacts from heat-induced convection and using the polarity switch of the applied electric field to retain spin phase modulations due to electrophoretic flow. Experiments were carried out with a mixture of 100 mM L-aspartic acid and 100 mM 4,9-dioxa-1,12-dodecanediamine to demonstrate this new method of ENMR. CC-ENMR enhances our previously developed capillary array ENMR (CA-ENMR) in solving the convection problem. The combined CA- and CC-ENMR approach strengthens the potential of multidimensional ENMR in simultaneous structural determination of coexisting proteins and protein conformations in biological buffer solutions of high ionic strength. Structural mapping of interacting proteins during biochemical reactions becomes possible in the future using ENMR techniques, which may have a profound impact on the understanding of biological events, including protein folding, genetic control, and signal transduction in general.

  4. Dynamic compensation in the central Pacific Ocean

    NASA Technical Reports Server (NTRS)

    Hinojosa, Juan Homero; Marsh, Bruce D.

    1988-01-01

    The intermediate-wavelength geoid (lambda similar to 2000 km) and sea-floor topography fields in the central Pacific Ocean were studied in terms of static and dynamic compensation models. Topographic features on the sea-floor with lambda less than 1000 km were found to be compensated both regionally, by the elastic strength of the lithosphere, and locally, by displacing mantle material to reach isostatic adjustment. The larger-scale sea-floor topography and the corresponding geoid anomalies with lambda similar to 2000 km cannot be explained by either local or regional compensation. The topography and the resulting geoid anomaly at this wavelength were modeled by considering the dynamic effects arising from viscous stresses in a layer of fluid with a highly temperature-dependent viscosity for the cases of: (1) surface cooling, and (2) basal heating. In this model, the mechanical properties of the elastic part of the lithosphere were taken into account by considering an activation energy of about 520 kJ/mol in the Arrhenius law for the viscosity. Numerical predictions of the topography, total geoid anomaly, and admittance were obtained, and the results show that the thermal perturbation in the layer, which accounts for the mass deficit, must be located close to the surface to compensate the gravitational effect of the surface deformation. For the case of basal heating, the temperature dependence of viscosity results in a separation of the upper, quasi-rigid lid from the lower mobile fluid, hence inhibiting the development of a compensating thermal perturbation at shallow depths. The results clearly rule out small-scale, upper-mantle convection as the source of these anomalies. Instead, the geophysical observables can be well explained by a shallow, transient thermal perturbation.

  5. Tritium activities in Canada supporting CANDU{sup R} nuclear power reactors

    SciTech Connect

    Miller, J. M.

    2008-07-15

    An overview of the various Canadian tritium research and operational activities supporting the development, refurbishment and operation of CANDU{sup R} nuclear power reactors is presented. These activities encompass tritium health and safety, tritium in the environment, tritium interaction with materials, and tritium processing, and relate to both supporting R and D advances as well as operational best practices. The collective results of these activities contribute to our goals of improving worker and public safety, and operational efficiency. (authors)

  6. Single Phase Passive Rectification Versus Active Rectification Applied to High Power Stirling Engines

    NASA Technical Reports Server (NTRS)

    Santiago, Walter; Birchenough, Arthur G.

    2006-01-01

    Stirling engine converters are being considered as potential candidates for high power energy conversion systems required by future NASA explorations missions. These types of engines typically contain two major moving parts, the displacer and the piston, in which a linear alternator is attached to the piston to produce a single phase sinusoidal waveform at a specific electric frequency. Since all Stirling engines perform at low electrical frequencies (less or equal to 100 Hz), space explorations missions that will employ these engines will be required to use DC power management and distribution (PMAD) system instead of an AC PMAD system to save on space and weight. Therefore, to supply such DC power an AC to DC converter is connected to the Stirling engine. There are two types of AC to DC converters that can be employed, a passive full bridge diode rectifier and an active switching full bridge rectifier. Due to the inherent line inductance of the Stirling Engine-Linear Alternator (SE-LA), their sinusoidal voltage and current will be phase shifted producing a power factor below 1. In order to keep power the factor close to unity, both AC to DC converters topologies will implement power factor correction. This paper discusses these power factor correction methods as well as their impact on overall mass for exploration applications. Simulation results on both AC to DC converters topologies with power factor correction as a function of output power and SE-LA line inductance impedance are presented and compared.

  7. An overview of turbulence compensation

    NASA Astrophysics Data System (ADS)

    Schutte, Klamer; van Eekeren, Adam W. M.; Dijk, Judith; Schwering, Piet B. W.; van Iersel, Miranda; Doelman, Niek J.

    2012-09-01

    In general, long range visual detection, recognition and identification are hampered by turbulence caused by atmospheric conditions. Much research has been devoted to the field of turbulence compensation. One of the main advantages of turbulence compensation is that it enables visual identification over larger distances. In many (military) scenarios this is of crucial importance. In this paper we give an overview of several software and hardware approaches to compensate for the visual artifacts caused by turbulence. These approaches are very diverse and range from the use of dedicated hardware, such as adaptive optics, to the use of software methods, such as deconvolution and lucky imaging. For each approach the pros and cons are given and it is indicated for which type of scenario this approach is useful. In more detail we describe the turbulence compensation methods TNO has developed in the last years and place them in the context of the different turbulence compensation approaches and TNO's turbulence compensation roadmap. Furthermore we look forward and indicate the upcoming challenges in the field of turbulence compensation.

  8. Design and real time implementation of fuzzy switched controller for single phase active power filter.

    PubMed

    Afghoul, Hamza; Krim, Fateh; Chikouche, Djamel; Beddar, Antar

    2015-09-01

    This paper proposes a novel fuzzy switched controller (FSC) integrated in direct current control (DCC) algorithm for single phase active power filter (SPAPF). The controller under study consists of conventional PI controller, fractional order PI controller (FO-PI) and fuzzy decision maker (FDM) that switches between them using reduced fuzzy logic control. The proposed controller offers short response time with low damping and deals efficiently with the external disturbances while preserving the robustness properties. To fulfill the requirements of power quality, unity power factor and harmonics limitations in active power filtering an experimental test bench has been built using dSPACE 1104 to demonstrate the feasibility and effectiveness of the proposed controller. The obtained results present high performance in steady and transient states. PMID:26233491

  9. An energy harvesting system for passively generating power from human activities

    NASA Astrophysics Data System (ADS)

    Rao, Yuan; Cheng, Shuo; Arnold, David P.

    2013-11-01

    This paper presents a complete, self-contained energy harvesting system composed of a magnetic energy harvester, an input-powered interface circuit and a rechargeable battery. The system converts motion from daily human activities such as walking, jogging, and cycling into usable electrical energy. By using an input-powered interface circuit, the system requires no external power supplies and features zero standby power when the input motion is too small for successful energy reclamation. When attached to a person's ankle during walking, the 100 cm3 system prototype is shown to charge a 3.7 V, 65 mAh lithium-ion polymer battery at an average power of 300 µW. The design and testing of the system under other operating conditions are presented herein.

  10. Activities in support of continuing the service of nuclear power plant concrete structures

    SciTech Connect

    Naus, Dan J

    2012-01-01

    In general, nuclear power plant concrete structure s performance has been very good; however, aging of concrete structures occurs with the passage of time that can potentially result in degradation if is effects are not controlled. Safety-related nuclear power plant concrete structures are described. In-service inspection and testing requirements in the U.S. are summarized. The interaction of the license renewal process and concrete structures is noted. A summary of operating experience related to aging of nuclear power plant concrete structures is provided. Several candidate areas are identified where additional research would be beneficial for aging management of nuclear power plant concrete structures. Finally, an update on recent activities at Oak Ridge National Laboratory related to aging management of nuclear power plant concrete structures is provided.

  11. Reduction in Power Consumption for Full-Color Active Matrix Organic Light-Emitting Devices

    NASA Astrophysics Data System (ADS)

    Kanno, Hiroshi; Hamada, Yuji; Nishimura, Kazuki; Okumoto, Kenji; Saito, Nobuo; Mameno, Kazunobu; Shibata, Kenichi

    2006-09-01

    The active matrix organic light-emitting diode (AMOLED) is expected to serve as next generation flat panels display with the outstanding features of wide viewing angle, vivid images, and quick response. For practical use of full-color AMOLEDs in mobile devices, it is essential to reduce the power consumption, which is generally higher than that of liquid crystal displays (LCDs). For this aim, a red, green, blue, and white (RGBW) pixel format combined with an RGB color filter array (RGBW format) with a common white emission layer (EML) has been developed. We find that the RGBW format can successfully reduce the power consumption of a full-color AMOLED by nearly half that of a conventionally filtered RGB pixel format. This improved power consumption is almost equal to the power consumption of a same-sized LCD. The RGBW format is a promising technique for the further reduction of the power consumption of a full-color AMOLED.

  12. Auditory Power-Law Activation Avalanches Exhibit a Fundamental Computational Ground State.

    PubMed

    Stoop, Ruedi; Gomez, Florian

    2016-07-15

    The cochlea provides a biological information-processing paradigm that we are only beginning to understand in its full complexity. Our work reveals an interacting network of strongly nonlinear dynamical nodes, on which even a simple sound input triggers subnetworks of activated elements that follow power-law size statistics ("avalanches"). From dynamical systems theory, power-law size distributions relate to a fundamental ground state of biological information processing. Learning destroys these power laws. These results strongly modify the models of mammalian sound processing and provide a novel methodological perspective for understanding how the brain processes information. PMID:27472144

  13. Auditory Power-Law Activation Avalanches Exhibit a Fundamental Computational Ground State

    NASA Astrophysics Data System (ADS)

    Stoop, Ruedi; Gomez, Florian

    2016-07-01

    The cochlea provides a biological information-processing paradigm that we are only beginning to understand in its full complexity. Our work reveals an interacting network of strongly nonlinear dynamical nodes, on which even a simple sound input triggers subnetworks of activated elements that follow power-law size statistics ("avalanches"). From dynamical systems theory, power-law size distributions relate to a fundamental ground state of biological information processing. Learning destroys these power laws. These results strongly modify the models of mammalian sound processing and provide a novel methodological perspective for understanding how the brain processes information.

  14. On the origin of power-law X-ray spectra of active galactic nuclei

    NASA Technical Reports Server (NTRS)

    Schlosman, I.; Shaham, J.; Shaviv, G.

    1984-01-01

    In the present analytical model for a power law X-ray continuum production in active galactic nuclei, the dissipation of turbulent energy flux above the accretion disk forms an optically thin transition layer with an inverted temperature gradient. The emitted thermal radiation has a power law spectrum in the 0.1-100 keV range, with a photon energy spectral index gamma of about 0.4-1.0. Thermal X-ray contribution from the layer is 5-10 percent of the total disk luminosity. The gamma value of 0.75 is suggested as a 'natural' power law index for Seyfert galaxies and QSOs.

  15. 33 CFR 136.113 - Other compensation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS... claimant must include an accounting, including the source and value, of all other compensation...

  16. Industrial Power Factor Analysis Guidebook.

    SciTech Connect

    Electrotek Concepts.

    1995-03-01

    Power factor is a way of measuring the percentage of reactive power in an electrical system. Reactive power represents wasted energy--electricity that does no useful work because the electrical current is out of phase with the voltage. Reactive power is used by inductive loads (such as, motors, transformers, fluorescent lights, arc welders and induction furnaces) to sustain their magnetic fields. Electric systems with many motors exhibit low power factors, increased conductor and transformer losses, and lower voltages. Utilities must supply both active and reactive power and compensate for these losses. Power factor can be improved by the addition of shunt capacitors. Capacitors act in opposition to inductive loads, thereby minimizing the reactive power required to serve them. In raising the power factor, shunt capacitors release energy to the system, reduce system losses, and ultimately decrease power costs. Improving system power factor can reduce reactive and active power losses for both industry and utilities through the addition of shunt capacitors. This Guide Book gives electric utility technical staff, industrial end-users, consultants and BPA employees a step-by-step method for evaluating the cost effectiveness of installing power factor correction capacitors in an industrial plant.

  17. NADH oxidase activity (NOX) and enlargement of HeLa cells oscillate with two different temperature-compensated period lengths of 22 and 24 minutes corresponding to different NOX forms

    NASA Technical Reports Server (NTRS)

    Wang, S.; Pogue, R.; Morre, D. M.; Morre, D. J.

    2001-01-01

    NOX proteins are cell surface-associated and growth-related hydroquinone (NADH) oxidases with protein disulfide-thiol interchange activity. A defining characteristic of NOX proteins is that the two enzymatic activities alternate to generate a regular period length of about 24 min. HeLa cells exhibit at least two forms of NOX. One is tumor-associated (tNOX) and is inhibited by putative quinone site inhibitors (e.g., capsaicin or the antitumor sulfonylurea, LY181984). Another is constitutive (CNOX) and refractory to inhibition. The periodic alternation of activities and drug sensitivity of the NADH oxidase activity observed with intact HeLa cells was retained in isolated plasma membranes and with the solubilized and partially purified enzyme. At least two activities were present. One had a period length of 24 min and the other had a period length of 22 min. The lengths of both the 22 and the 24 min periods were temperature compensated (approximately the same when measured at 17, 27 or 37 degrees C) whereas the rate of NADH oxidation approximately doubled with each 10 degrees C rise in temperature. The rate of increase in cell area of HeLa cells when measured by video-enhanced light microscopy also exhibited a complex period of oscillations reflective of both 22 and 24 min period lengths. The findings demonstrate the presence of a novel oscillating NOX activity at the surface of cancer cells with a period length of 22 min in addition to the constitutive NOX of non-cancer cells and tissues with a period length of 24 min.

  18. 31 CFR 30.16 - Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? 30... FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.16 Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? (a) The Office...

  19. 31 CFR 30.16 - Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? 30... FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.16 Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? (a) The Office...

  20. 31 CFR 30.16 - Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? 30... FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.16 Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? (a) The Office...

  1. 31 CFR 30.16 - Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? 30... FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.16 Q-16: What is the Office of the Special Master for TARP Executive Compensation, and what are its powers, duties and responsibilities? (a) The Office...

  2. Self Organization in Compensated Semiconductors

    NASA Astrophysics Data System (ADS)

    Berezin, Alexander A.

    2004-03-01

    In partially compensated semiconductor (PCS) Fermi level is pinned to donor sub-band. Due to positional randomness and almost isoenergetic hoppings, donor-spanned electronic subsystem in PCS forms fluid-like highly mobile collective state. This makes PCS playground for pattern formation, self-organization, complexity emergence, electronic neural networks, and perhaps even for origins of life, bioevolution and consciousness. Through effects of impact and/or Auger ionization of donor sites, whole PCS may collapse (spinodal decomposition) into microblocks potentially capable of replication and protobiological activity (DNA analogue). Electronic screening effects may act in RNA fashion by introducing additional length scale(s) to system. Spontaneous quantum computing on charged/neutral sites becomes potential generator of informationally loaded microstructures akin to "Carl Sagan Effect" (hidden messages in Pi in his "Contact") or informational self-organization of "Library of Babel" of J.L. Borges. Even general relativity effects at Planck scale (R.Penrose) may affect the dynamics through (e.g.) isotopic variations of atomic mass and local density (A.A.Berezin, 1992). Thus, PCS can serve as toy model (experimental and computational) at interface of physics and life sciences.

  3. Temperature-compensating dc restorer

    NASA Technical Reports Server (NTRS)

    Thomas, H. M.

    1980-01-01

    Circuit provides stable references restoration in addition to temperature compensation. Possible TV monitor applications include traffic and security surveillance systems, where cameras are subject to environmental extremes, as in unheated warehouses or outdoors.

  4. Measurement of Carbon Dioxide Compensation Points of Freshwater Algae 1

    PubMed Central

    Birmingham, Brendan C.; Colman, Brian

    1979-01-01

    A technique is described for the measurement of total dissolved inorganic carbon by acid release as CO2 followed by its conversion to methane and detection by flame ionization in a modified gas chromatograph. This method was used to determine the dissolved inorganic carbon concentration reached at compensation point when algae were allowed to photosynthesize in a closed system in a buffer at known pH, and the CO2 compensation point was calculated from this concentration. The CO2 compensation points of 16 freshwater algae were measured at acid and alkaline pH in air-saturated medium: at acid pH the CO2 compensation points ranged from 4.8 to 41.5 microliters per liter while at alkaline pH they ranged from 0.2 to 7.2 microliters per liter. Removal of O2 from the medium caused a slight lowering of compensation point at acid pH but had little effect at alkaline pH. These low, O2-insensitive compensation points are characteristic of C4 plants. It is suggested that these low CO2 compensation points are maintained by an active bicarbonate uptake by algae especially at alkaline pH. PMID:16661077

  5. THE EFFECT OF POWERED ACTIVATED CARBON IN A PETROLEUM REFINERY ACTIVATED SLUDGE TREATMENT SYSTEM

    EPA Science Inventory

    The purpose of this research program was to determine the effect of the addition of powdered activated carbon (PAC) to refinery activated sludge systems. Bench-scale and full-scale tests were performed. A wide range of PAC concentrations and sludge ages were evaluated. Bench-scal...

  6. Motion compensation for brain PET imaging using wireless MR active markers in simultaneous PET-MR: phantom and non-human primate studies

    PubMed Central

    Huang, Chuan; Ackerman, Jerome L.; Petibon, Yoann; Normandin, Marc D.; Brady, Thomas J.; El Fakhri, Georges; Ouyang, Jinsong

    2014-01-01

    Brain PET scanning plays an important role in the diagnosis, prognostication and monitoring of many brain diseases. Motion artifacts from head motion are one of the major hurdles in brain PET. In this work, we propose to use wireless MR active markers to track head motion in real time during a simultaneous PET-MR brain scan and incorporate the motion measured by the markers in the listmode PET reconstruction. Several wireless MR active markers and a dedicated fast MR tracking pulse sequence module were built. Data were acquired on an ACR Flangeless PET phantom with multiple spheres and a non-human primate with and without motion. Motions of the phantom and monkey’s head were measured with the wireless markers using a dedicated MR tracking sequence module. The motion PET data were reconstructed using list-mode reconstruction with and without motion correction. Static reference was used as gold standard for quantitative analysis. The motion artifacts, which were prominent on the images without motion correction, were eliminated by the wireless marker based motion correction in both the phantom and monkey experiments. Quantitative analysis was performed on the phantom motion data from 24 independent noise realizations. The reduction of bias of sphere-to-background PET contrast by active marker based motion correction ranges from 26% to 64% and 17% to 25% for hot (i.e., radioactive) and cold (i.e., non-radioactive) spheres, respectively. The motion correction improved the channelized Hotelling observer signal-to-noise ratio of the spheres by 1.2 to 6.9 depending on their locations and sizes. The proposed wireless MR active marker based motion correction technique removes the motion artifacts in the reconstructed PET images and yields accurate quantitative values. PMID:24418501

  7. Motion compensation for brain PET imaging using wireless MR active markers in simultaneous PET-MR: phantom and non-human primate studies.

    PubMed

    Huang, Chuan; Ackerman, Jerome L; Petibon, Yoann; Normandin, Marc D; Brady, Thomas J; El Fakhri, Georges; Ouyang, Jinsong

    2014-05-01

    Brain PET scanning plays an important role in the diagnosis, prognostication and monitoring of many brain diseases. Motion artifacts from head motion are one of the major hurdles in brain PET. In this work, we propose to use wireless MR active markers to track head motion in real time during a simultaneous PET-MR brain scan and incorporate the motion measured by the markers in the listmode PET reconstruction. Several wireless MR active markers and a dedicated fast MR tracking pulse sequence module were built. Data were acquired on an ACR Flangeless PET phantom with multiple spheres and a non-human primate with and without motion. Motions of the phantom and monkey's head were measured with the wireless markers using a dedicated MR tracking sequence module. The motion PET data were reconstructed using list-mode reconstruction with and without motion correction. Static reference was used as gold standard for quantitative analysis. The motion artifacts, which were prominent on the images without motion correction, were eliminated by the wireless marker based motion correction in both the phantom and monkey experiments. Quantitative analysis was performed on the phantom motion data from 24 independent noise realizations. The reduction of bias of sphere-to-background PET contrast by active marker based motion correction ranges from 26% to 64% and 17% to 25% for hot (i.e., radioactive) and cold (i.e., non-radioactive) spheres, respectively. The motion correction improved the channelized Hotelling observer signal-to-noise ratio of the spheres by 1.2 to 6.9 depending on their locations and sizes. The proposed wireless MR active marker based motion correction technique removes the motion artifacts in the reconstructed PET images and yields accurate quantitative values. PMID:24418501

  8. Fast Power Line Detection and Localization Using Steerable Filter for Active Uav Guidance

    NASA Astrophysics Data System (ADS)

    Liu, Y.; Mejias, L.; Li, Z.

    2012-08-01

    In this paper we present a fast power line detection and localisation algorithm as well as propose a high-level guidance architecture for active vision-based Unmanned Aerial Vehicle (UAV) guidance. The detection stage is based on steerable filters for edge ridge detection, followed by a line fitting algorithm to refine candidate power lines in images. The guidance architecture assumes an UAV with an onboard Gimbal camera. We first control the position of the Gimbal such that the power line is in the field of view of the camera. Then its pose is used to generate the appropriate control commands such that the aircraft moves and flies above the lines. We present initial experimental results for the detection stage which shows that the proposed algorithm outperforms two state-of-the-art line detection algorithms for power line detection from aerial imagery.

  9. Comparison of bidirectional power electronics with unidirectional topologies using active discharging circuits for feeding DEAP transducer

    NASA Astrophysics Data System (ADS)

    Hoffstadt, Thorben; Maas, Jürgen

    2015-04-01

    To enable a continuous operation of a DEAP transducer, the feeding power electronics must provide the capability to charge and discharge the transducer to enable a continuous voltage adjustment. While in case of energy harvesting applications a bidirectional power electronics is mandatory, for actuator applications also unidirectional power electronics with active discharging circuits can be used. Thus, in this contribution a bidirectional flyback-converter is compared to a unidirectional with different discharging circuits. For this purpose, the design of a resistive and an inductive-resistive discharging circuit is proposed, that are connected in parallel to the DEAP and activated when required. Modulation schemes for both discharging circuits are derived that enable a continuous voltage control. Based on realized prototypes of the investigated topologies the different converters are finally compared to each other.

  10. Power spectral analysis of autonomic nervous activity in spontaneously hypertensive rats.

    PubMed

    Ju, K; Kubo, T

    1997-01-01

    We studied power spectral analysis of heart rate variability (HRV) in control spontaneously hypertensive rats (SHR) and tourmaline hydroxyl negative ion-treated SHR groups. The power spectrum of HRV in SHR groups was composed of two frequency components; low frequency (LF, 0.005 approximately 1.0 Hz) and high frequency (HF, 1.0 approximately 2.0 Hz) components. The low frequency power (LFP) of HRV spectrum, which indicates sympathetic nervous activity, in negative air ion-treated SHR group was significantly (p < 0.01) smaller than in control SHR group. And also we obtained that the high frequency power (HFP) showing parasympathetic nervous activity in negative air ion-treated SHR group was significantly (p < 0.01) higher than in control SHR group. It could be concluded that hydroxyl negative air ions generated by tourmaline ionizer system decreased the elevated blood pressure, and control the sympathetic nervous activity and the parasympathetic nervous activity in SHR having the elevated blood pressure. PMID:9731382

  11. Power Perceptions and Negotiations in a Cross-National Email Writing Activity

    ERIC Educational Resources Information Center

    Liu, Yichun

    2011-01-01

    The present study investigates EFL students' perceptions of power differentials and their negotiation strategies when communicating with native English-speaking students via emails. The study involved 28 Taiwanese and American undergraduates who participated in a semester-long cross-national email writing activity. Findings show that students in…

  12. Star Power: Providing for the Gifted & Talented. Module 5. Enrichment Activities for the Gifted/Talented.

    ERIC Educational Resources Information Center

    Mallis, Jackie; Gilman, Sharlene

    The document presents Module 5, enrichment activities for the gifted/talented, of the Star Power modules developed for school personnel who have an interest in or a need to explore the area of gifted and talented education. It is explained in an introductory section that the modules can be used for independent study, for small group interaction,…

  13. T & I--Electricity. Power. Kit No. 52. Instructor's Manual [and] Student Learning Activity Guide.

    ERIC Educational Resources Information Center

    Jones, Phillip

    An instructor's manual and student activity guide on electrical power are provided in this set of prevocational education materials which focuses on the vocational area of trade and industry. (This set of materials is one of ninety-two prevocational education sets arranged around a cluster of seven vocational offerings: agriculture, home…

  14. T & I, Power Mechanics. Kit No. 35. Instructor's Manual [and] Student Learning Activity Guide.

    ERIC Educational Resources Information Center

    Underwood, Earl

    An instructor's manual and student activity guide on power mechanics are provided in this set of prevocational education materials which focuses on the vocational area of trade and industry. (This set of materials is one of ninety-two prevocational education sets arranged around a cluster of seven vocational offerings: agriculture, home economics,…

  15. X-Chromosome dosage compensation.

    PubMed

    Meyer, Barbara J

    2005-01-01

    In mammals, flies, and worms, sex is determined by distinctive regulatory mechanisms that cause males (XO or XY) and females (XX) to differ in their dose of X chromosomes. In each species, an essential X chromosome-wide process called dosage compensation ensures that somatic cells of either sex express equal levels of X-linked gene products. The strategies used to achieve dosage compensation are diverse, but in all cases, specialized complexes are targeted specifically to the X chromosome(s) of only one sex to regulate transcript levels. In C. elegans, this sex-specific targeting of the dosage compensation complex (DCC) is controlled by the same developmental signal that establishes sex, the ratio of X chromosomes to sets of autosomes (X:A signal). Molecular components of this chromosome counting process have been defined. Following a common step of regulation, sex determination and dosage compensation are controlled by distinct genetic pathways. C. elegans dosage compensation is implemented by a protein complex that binds both X chromosomes of hermaphrodites to reduce transcript levels by one-half. The dosage compensation complex resembles the conserved 13S condensin complex required for both mitotic and meiotic chromosome resolution and condensation, implying the recruitment of ancient proteins to the new task of regulating gene expression. Within each C. elegans somatic cell, one of the DCC components also participates in the separate mitotic/meiotic condensin complex. Other DCC components play pivotal roles in regulating the number and distribution of crossovers during meiosis. The strategy by which C. elegans X chromosomes attract the condensin-like DCC is known. Small, well-dispersed X-recognition elements act as entry sites to recruit the dosage compensation complex and to nucleate spreading of the complex to X regions that lack recruitment sites. In this manner, a repressed chromatin state is spread in cis over short or long distances, thus establishing the

  16. 29 CFR 525.6 - Compensable time.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 3 2013-07-01 2013-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those...

  17. 29 CFR 525.6 - Compensable time.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those...

  18. 48 CFR 752.7007 - Personnel compensation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Personnel compensation... Personnel compensation. The following clause shall be used in all USAID cost-reimbursement contracts. Personnel Compensation (JUL 2007) (a) Direct compensation of the Contractor's personnel will be...

  19. 38 CFR 3.459 - Death compensation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Death compensation. 3.459 Section 3.459 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.459 Death compensation. (a)...

  20. 29 CFR 525.6 - Compensable time.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 3 2011-07-01 2011-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those...

  1. 38 CFR 3.459 - Death compensation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2014-07-01 2014-07-01 false Death compensation. 3.459 Section 3.459 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.459 Death compensation. (a)...

  2. 38 CFR 3.459 - Death compensation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2013-07-01 2013-07-01 false Death compensation. 3.459 Section 3.459 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.459 Death compensation. (a)...

  3. 38 CFR 3.459 - Death compensation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2012-07-01 2012-07-01 false Death compensation. 3.459 Section 3.459 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.459 Death compensation. (a)...

  4. 38 CFR 3.459 - Death compensation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2011-07-01 2011-07-01 false Death compensation. 3.459 Section 3.459 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.459 Death compensation. (a)...

  5. 48 CFR 970.2270 - Unemployment compensation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to...

  6. 48 CFR 970.2270 - Unemployment compensation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to...

  7. 48 CFR 970.2270 - Unemployment compensation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to...

  8. 48 CFR 970.2270 - Unemployment compensation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to...

  9. 48 CFR 970.2270 - Unemployment compensation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to...

  10. 29 CFR 525.6 - Compensable time.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 3 2012-07-01 2012-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those...

  11. 29 CFR 525.6 - Compensable time.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 3 2014-07-01 2014-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those...

  12. Targeted impairment of thymidine kinase 2 expression in cells induces mitochondrial DNA depletion and reveals molecular mechanisms of compensation of mitochondrial respiratory activity

    SciTech Connect

    Villarroya, Joan; Lara, Mari-Carmen; Dorado, Beatriz; Garrido, Marta; Garcia-Arumi, Elena; Meseguer, Anna; Hirano, Michio; Vila, Maya R.

    2011-04-08

    Highlights: {yields} We impaired TK2 expression in Ost TK1{sup -} cells via siRNA-mediated interference (TK2{sup -}). {yields} TK2 impairment caused severe mitochondrial DNA (mtDNA) depletion in quiescent cells. {yields} Despite mtDNA depletion, TK2{sup -} cells show high cytochrome oxidase activity. {yields} Depletion of mtDNA occurs without imbalance in the mitochondrial dNTP pool. {yields} Nuclear-encoded ENT1, DNA-pol {gamma}, TFAM and TP gene expression is lowered in TK2{sup -} cells. -- Abstract: The mitochondrial DNA (mtDNA) depletion syndrome comprises a clinically heterogeneous group of diseases characterized by reductions of the mtDNA abundance, without associated point mutations or rearrangements. We have developed the first in vitro model to study of mtDNA depletion due to reduced mitochondrial thymidine kinase 2 gene (TK2) expression in order to understand the molecular mechanisms involved in mtDNA depletion syndrome due to TK2 mutations. Small interfering RNA targeting TK2 mRNA was used to decrease TK2 expression in Ost TK1{sup -} cells, a cell line devoid of endogenous thymidine kinase 1 (TK1). Stable TK2-deficient cell lines showed a reduction of TK2 levels close to 80%. In quiescent conditions, TK2-deficient cells showed severe mtDNA depletion, also close to 80% the control levels. However, TK2-deficient clones showed increased cytochrome c oxidase activity, higher cytochrome c oxidase subunit I transcript levels and higher subunit II protein expression respect to control cells. No alterations of the deoxynucleotide pools were found, whereas a reduction in the expression of genes involved in nucleoside/nucleotide homeostasis (human equilibrative nucleoside transporter 1, thymidine phosphorylase) and mtDNA maintenance (DNA-polymerase {gamma}, mitochondrial transcription factor A) was observed. Our findings highlight the importance of cellular compensatory mechanisms that enhance the expression of respiratory components to ensure respiratory activity

  13. 96. Photocopied August 1978. COMPENSATING WORKS SITE (GATES 1316) WITH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    96. Photocopied August 1978. COMPENSATING WORKS SITE (GATES 13-16) WITH COFFER DAM IN PLACE AND WORK SITE BEING PUMPED DRY FOR FOUNDATION WORK, JUNE 5, 1915. (596) - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

  14. A Novel Control algorithm based DSTATCOM for Load Compensation

    NASA Astrophysics Data System (ADS)

    R, Sreejith; Pindoriya, Naran M.; Srinivasan, Babji

    2015-11-01

    Distribution Static Compensator (DSTATCOM) has been used as a custom power device for voltage regulation and load compensation in the distribution system. Controlling the switching angle has been the biggest challenge in DSTATCOM. Till date, Proportional Integral (PI) controller is widely used in practice for load compensation due to its simplicity and ability. However, PI Controller fails to perform satisfactorily under parameters variations, nonlinearities, etc. making it very challenging to arrive at best/optimal tuning values for different operating conditions. Fuzzy logic and neural network based controllers require extensive training and perform better under limited perturbations. Model predictive control (MPC) is a powerful control strategy, used in the petrochemical industry and its application has been spread to different fields. MPC can handle various constraints, incorporate system nonlinearities and utilizes the multivariate/univariate model information to provide an optimal control strategy. Though it finds its application extensively in chemical engineering, its utility in power systems is limited due to the high computational effort which is incompatible with the high sampling frequency in these systems. In this paper, we propose a DSTATCOM based on Finite Control Set Model Predictive Control (FCS-MPC) with Instantaneous Symmetrical Component Theory (ISCT) based reference current extraction is proposed for load compensation and Unity Power Factor (UPF) action in current control mode. The proposed controller performance is evaluated for a 3 phase, 3 wire, 415 V, 50 Hz distribution system in MATLAB Simulink which demonstrates its applicability in real life situations.

  15. Surgical compensation of presbyopia with corneal inlays.

    PubMed

    Konstantopoulos, Aris; Mehta, Jodhbir S

    2015-05-01

    Presbyopia, the physiological change in near vision that develops with ageing, gradually affects individuals older than 40 years and is a growing cause of visual disability due to ageing demographics of the global population. The routine use of computers and 'smartphones', combined with the affluence of the 'baby boomers' generation has set high standards for near vision correction. Corneal inlays are a relatively new treatment modality that is effective at compensating for presbyopia. The dimensions of these devices vary from 2 to 3.8 mm in diameter and 5 to 32 μm in thickness. They are implanted in the anterior corneal stroma of the non-dominant eye, most commonly, in a femtosecond laser created corneal pocket. They improve near vision by increasing the depth of focus, creating a hyper-prolate region of increased central cornea power or providing a refractive add power. This article reviews the literature on the efficacy and safety of corneal inlays. PMID:25652889

  16. Aeroballistic analyses for the Atmospheric Compensation Experiment

    SciTech Connect

    Millard, W.A.

    1986-01-01

    The Atmospheric Compensation Experiment (ACE) involved illuminating a sounding rocket payload with a low power laser from the Air Force Maui Optical Site (AMOS), Mt. Haleakala, HI. This experiment, sponsored by DARPA and SDIO, included four launches of Terrier Malemute II rocket vehicles from the Kauai Test Facility during the period July through Dec., 1985. The purpose of ACE was to demonstrate an adaptive optics technology that allowed the efficient transfer of power from the laser to the space target. This paper discusses the rationale used in selecting the launch site and the requirements for the carrier rocket system. Each payload carried a light detector array along its longitudinal axis, and it was necessary that this array be oriented perpendicular to the line of sight from AMOS to the payload. The design requirements for the payload attitude control system to satisfy this requirement are presented. Flight test results from the four tests showing flight performance and payload pointing data are included.

  17. Compensation, radiographic changes, and survival in applicants for asbestosis compensation.

    PubMed Central

    Cookson, W O; Musk, A W; Glancy, J J; de Klerk, N H; Yin, R; Mele, R; Carr, N G; Armstrong, B K; Hobbs, M S

    1985-01-01

    The survival of 354 claimants for compensation for pulmonary asbestosis among former workers of the Wittenoom crocidolite mine and mill in Western Australia has been examined. There were 118 deaths up to December 1982. The median time between start of work and claim for compensation was 17 years. The standardised mortality ratio (SMR) for deaths from all causes was 2.65 (p less than 0.0001). The SMR for pneumoconiosis was 177.2 (p less than 0.0001), bronchitis and emphysema 2.6 (p = 0.04), tuberculosis 44.6 (p less than 0.0001), respiratory cancer (including five deaths from malignant pleural mesothelioma) 6.4 (p less than 0.0001), gastrointestinal cancer 1.6 (p = 0.22), all other cancers 1.6 (p = 0.17), heart disease 1.4 (p = 0.07), and all other causes 2.18 (p = 0.004). Plain chest radiographs taken within two years of claiming compensation were found for 238 subjects and were categorised independently by two observers according to the International Labour Organisation criteria without knowledge of exposure or compensation details. Profusion of radiographic opacities, age at claiming compensation, work in the Wittenoom mill, and degree of disability awarded by the pneumoconiosis medical board were significant predictors of survival, but total estimated exposure to asbestos was not. Radiographic profusion and degree of disability were, however, predictable by total exposure. The median survival from claim for compensation was 17 years in subjects with ILO category 1 pneumoconiosis, 12 years in category 2, and three years in category 3. PMID:2990524

  18. Flexible OFDM-based access systems with intrinsic function of chromatic dispersion compensation

    NASA Astrophysics Data System (ADS)

    Konishi, Tsuyoshi; Murakawa, Takuya; Nagashima, Tomotaka; Hasegawa, Makoto; Shimizu, Satoshi; Hattori, Kuninori; Okuno, Masayuki; Mino, Shinji; Himeno, Akira; Uenohara, Hiroyuki; Wada, Naoya; Cincotti, Gabriella

    2015-12-01

    Cost-effective and tunable chromatic dispersion compensation in a fiber link are still an open issue in metro and access networks to cope with increasing costs and power consumption. Intrinsic chromatic dispersion compensation functionality of optical fractional orthogonal frequency division multiplexing is discussed and experimentally demonstrated using dispersion-tunable transmitter and receiver based on wavelength selective switching devices.

  19. The production of activated carbon using the equipment of thermal power plants and heating plants

    NASA Astrophysics Data System (ADS)

    Osintsev, K. V.; Osintsev, V. V.; Dzhundubaev, A. K.; Kim, S. P.; Al'musin, G. T.; Akbaev, T. A.; Bogatkin, V. I.

    2013-08-01

    The production technology of activated carbon using the conventional equipment of the thermal power stations and boiler houses is proposed. The obtained product is directed into the systems of chemical water preparation and water drain of enterprises. The production cycle is invariable when producing the activated carbon by the proposed technology. The fuel consumption and heat losses are considerably reduced when implementing this technology compared with the known analogs of the carbon sorbent. The production efficiency increases if small dust particles are preliminary separated and coal is activated in narrow ranges of fraction sizes.

  20. Active energy harvesting from microbial fuel cells at the maximum power point without using resistors.

    PubMed

    Wang, Heming; Park, Jae-Do; Ren, Zhiyong

    2012-05-01

    Microbial fuel cell (MFC) technology offers a sustainable approach to harvest electricity from biodegradable materials. Energy production from MFCs has been demonstrated using external resistors or charge pumps, but such methods can only dissipate energy through heat or receive electrons passively from the MFC without any controllability. This study developed a new approach and system that can actively extract energy from MFC reactors at any operating point without using any resistors, especially at the peak power point to maximize energy production. Results show that power harvesting from a recirculating-flow MFC can be well maintained by the maximum power point circuit (MPPC) at its peak power point, while a charge pump was not able to change operating point due to current limitation. Within 18-h test, the energy gained from the MPPC was 76.8 J, 76 times higher than the charge pump (1.0 J) that was commonly used in MFC studies. Both conditions resulted in similar organic removal, but the Coulombic efficiency obtained from the MPPC was 21 times higher than that of the charge pump. Different numbers of capacitors could be used in the MPPC for various energy storage requirements and power supply, and the energy conversion efficiency of the MPPC was further characterized to identify key factors for system improvement. This active energy harvesting approach provides a new perspective for energy harvesting that can maximize MFC energy generation and system controllability. PMID:22486712

  1. EMITTANCE COMPENSATION FOR MAGNETIZED BEAMS

    SciTech Connect

    KEWISCH,J.; CHANG, X.

    2007-06-25

    Emittance compensation is a well established technique for minimizing the emittance of an electron beam from a RF photo-cathode gun. Longitudinal slices of a bunch have a small emittance, but due to the longitudinal charge distribution of the bunch and time dependent RF fields they are not focused in the same way, so that the direction of their phase ellipses diverges in phase space and the projected emittance is much larger. Emittance compensation reverses the divergence. At the location where the slopes of the phase ellipses coincide the beam is accelerated, so that the space charge forces are reduced. A recipe for emittance compensation is given in. For magnetized beams (where the angular momentum is non-zero) such emittance compensation is not sufficient because variations in the slice radius lead to variations in the angular speed and therefore to an increase of emittance in the rotating game. We describe a method and tools for a compensation that includes the beam magnetization.

  2. Transcriptional activation of antioxidants may compensate for selenoprotein deficiencies in Amblyomma maculatum (Acari: Ixodidae) injected with selK- or selM-dsRNA

    PubMed Central

    Adamson, Steven; Browning, Rebecca; Singh, Parul; Nobles, Sarah; Villarreal, Ashley; Karim, Shahid

    2014-01-01

    The Gulf-Coast tick, Amblyomma maculatum, possesses an elaborate set of selenoprotein, which prevent the deleterious effects from oxidative stress that occur during feeding. In the current work, we examined the role of Selenoprotein K (SelK) and Selenoprotein M (SelM) in feeding A. maculatum by bioinformatics, transcriptional gene expression, RNA interference and antioxidant assays. The transcriptional expression of SelK does not vary significantly in salivary glands or midguts throughout the blood meal. However, there is a 58-fold increase in transcript levels of SelM in tick midguts. Ticks injected with selK-dsRNA or selM-dsRNA did not reveal any observable differences in egg viability but oviposition was reduced. Surprisingly, salivary antioxidant activity was higher in selenoprotein knockouts compared to controls, which is likely due to compensatory transcriptional expression of genes involved in combating reactive oxygen species. In fact, RT-qPCR data suggest the transcriptional expression of catalase increased in ticks injected with selM-dsRNA. Additionally, the transcriptional expression of selN decreased ~90% in both SelK/SelM knockdowns. PMID:24698418

  3. Multipolar, time-dynamical model for the loss compensation and lasing of a spherical plasmonic nanoparticle spaser immersed in an active gain medium.

    PubMed

    Veltri, Alessandro; Chipouline, Arkadi; Aradian, Ashod

    2016-01-01

    The plasmonic response of a metal nanoparticle in the presence of surrounding gain elements is studied, using a space and time-dependent model, which integrates a quantum formalism to describe the gain and a classical treatment for the metal. Our model fully takes into account the influence of the system geometry (nanosphere) and offers for the first time, the possibility to describe the temporal evolution of the fields and the coupling among the multipolar modes of the particle. We calculate the lasing threshold value for all multipoles of the spaser, and demonstrate that the dipolar one is lowest. The onset of the lasing instability, in the linear regime, is then studied both with and without external field forcing. We also study the behaviour of the system below the lasing threshold, with the external field, demonstrating the existence of an amplification regime where the nanoparticle's plasmon is strongly enhanced as the threshold is approached. Finally, a qualitative discussion is provided on later, non-linear stages of the dynamics and the approach to the steady-state of the spaser; in particular, it is shown that, for the considered geometry, the spasing is necessarily multi-modal and multipolar modes are always activated. PMID:27625072

  4. An embryonic myosin isoform enables stretch activation and cyclical power in Drosophila jump muscle.

    PubMed

    Zhao, Cuiping; Swank, Douglas M

    2013-06-18

    The mechanism behind stretch activation (SA), a mechanical property that increases muscle force and oscillatory power generation, is not known. We used Drosophila transgenic techniques and our new muscle preparation, the jump muscle, to determine if myosin heavy chain isoforms influence the magnitude and rate of SA force generation. We found that Drosophila jump muscles show very low SA force and cannot produce positive power under oscillatory conditions at pCa 5.0. However, we transformed the jump muscle to be moderately stretch-activatable by replacing its myosin isoform with an embryonic isoform (EMB). Expressing EMB, jump muscle SA force increased by 163% and it generated net positive power. The rate of SA force development decreased by 58% with EMB expression. Power generation is Pi dependent as >4 mM Pi was required for positive power from EMB. Pi increased EMB SA force, but not wild-type SA force. Our data suggest that when muscle expressing EMB is stretched, EMB is more easily driven backward to a weakly bound state than wild-type jump muscle. This increases the number of myosin heads available to rapidly bind to actin and contribute to SA force generation. We conclude that myosin heavy chain isoforms influence both SA kinetics and SA force, which can determine if a muscle is capable of generating oscillatory power at a fixed calcium concentration. PMID:23790374

  5. Pitching-motion-activated flapping foil near solid walls for power extraction: A numerical investigation

    NASA Astrophysics Data System (ADS)

    Wu, J.; Qiu, Y. L.; Shu, C.; Zhao, N.

    2014-08-01

    A numerical investigation on the power extraction of a pitching-motion-activated flapping foil near solid walls is performed by using an immersed boundary-lattice Boltzmann method in this study. The flapping motions of the foil include a forced pitching component and an induced plunging component. The foil is placed either near a solid wall or between two parallel plane walls. Compared to previous work on the flapping foil for power extraction, the effect of the walls is first considered in this work. At a Reynolds number of 1100 and with the position of the foil pitching axis at third chord, the influences of the mechanical parameters (such as damping coefficient and spring constant) of the foil, the amplitude and frequency of the pitching motion and the clearance between the foil pitching axis and the wall on the power extraction performance of the flapping foil are systematically evaluated. Compared to the situation of free stream, the power extraction performance of the foil near the wall is improved. For given amplitude and frequency, as the clearance decreases the net power extraction efficiency improves. Moreover, as the foil is placed near one wall, there is a transverse shift to the plunging motion that consequently weakens the improvement of net power extraction efficiency. In contrast, the shift can be significantly eliminated as the foil is placed between two walls, which can further improve the net power extraction efficiency. In addition, it is found that the efficiency improvement is essentially from the increased power extraction, which is due to the generation of high lift force.

  6. Active photonic sensor communication cable for field application of optical data and power transmission

    NASA Astrophysics Data System (ADS)

    Suthau, Eike; Rieske, Ralf; Zerna, Thomas

    2014-10-01

    Omitting electrically conducting wires for sensor communication and power supply promises protection for sensor systems and monitored structures against lightning or high voltages, prevention of explosion hazards, and reduction of susceptibility to tampering. The ability to photonically power remote systems opens up the full range of electrical sensors. Power-over-fiber is an attractive option in electromagnetically sensitive environments, particularly for longterm, maintenance-free applications. It can deliver uninterrupted power sufficient for elaborate sensors, data processing or even actuators alongside continuous high speed data communication for remote sensor application. This paper proposes an active photonic sensor communication system, which combines the advantages of optical data links in terms of immunity to electromagnetic interference (EMI), high bandwidth, hardiness against tampering or eavesdropping, and low cable weight with the robustness one has come to expect from industrial or military electrical connectors. An application specific integrated circuit (ASIC) is presented that implements a closed-loop regulation of the sensor power supply to guarantee continuous, reliable data communications while maintaining a highly efficient, adaptive sensor supply scheme. It is demonstrated that the resulting novel photonic sensor communication cable can handle sensors and actuators differing orders of magnitude with respect to power consumption. The miniaturization of the electro-optical converters and driving electronics is as important to the presented development as the energy efficiency of the detached, optically powered sensor node. For this reason, a novel photonic packaging technology based on wafer-level assembly of the laser power converters by means of passive alignment will be disclosed in this paper.

  7. Compensation for electrical converter nonlinearities

    SciTech Connect

    Perisic, Milun; Ransom, Ray M; Kajouke, Lateef A

    2013-11-19

    Systems and methods are provided for delivering energy from an input interface to an output interface. An electrical system includes an input interface, an output interface, an energy conversion module between the input interface and the output interface, an inductive element between the input interface and the energy conversion module, and a control module. The control module determines a compensated duty cycle control value for operating the energy conversion module to produce a desired voltage at the output interface and operates the energy conversion module to deliver energy to the output interface with a duty cycle that is influenced by the compensated duty cycle control value. The compensated duty cycle control value is influenced by the current through the inductive element and accounts for voltage across the switching elements of the energy conversion module.

  8. Compensation and Recovery From Injury

    PubMed Central

    Beals, Rodney K.

    1984-01-01

    Workers' compensation laws influence recovery from injury. They affect the “cause” of disease, access to care, diagnostic evaluation, treatment, response to treatment and residual disability. Paradoxically, financial compensation may discourage return to work, the appeal process may increase disability, an open claim may inhibit return to work and recovering patients may be unable to return to work. Physicians may help improve the prospects of returning patients to work by providing care that is medical, caring and independent. It is essential that the treatment of back pain be based on the known natural history and on the understanding that the management of acute pain differs from that of chronic pain. Increased awareness of the factors controlling return to work should motivate legislative bodies, labor and industry to alter those features of the compensation system that interfere with the return to work of injured workers. PMID:6233794

  9. Activation characteristics of a solid breeder blanket for a fusion power demonstration reactor

    NASA Astrophysics Data System (ADS)

    Fischer, Ulrich; Tsige-Tamirat, Haileyesus

    2002-12-01

    Activation characteristics have been assessed for a helium cooled solid breeder blanket on the basis of three-dimensional activation calculations for a 2200 MW fusion power demonstration reactor. FISPACT inventory calculations were performed for the beryllium neutron multiplier, the Li 4SiO 4 breeder ceramics and the Eurofer low activation steel. Neutron flux spectra distributions were provided by a previous MCNP calculation. Detailed spatial distributions have been obtained for the nuclide inventories and related quantities such as activity, decay heat and contact dose rate. These data are available form the authors upon request. On the basis of the calculated contact gamma dose rates, the waste quality was assessed with regard to a possible re-use of the activated materials following the remote or the hands-on handling recycling options.

  10. A Powerful CRISPR/Cas9-Based Method for Targeted Transcriptional Activation.

    PubMed

    Katayama, Shota; Moriguchi, Tetsuo; Ohtsu, Naoki; Kondo, Toru

    2016-05-23

    Targeted transcriptional activation of endogenous genes is important for understanding physiological transcriptional networks, synthesizing genetic circuits, and inducing cellular phenotype changes. The CRISPR/Cas9 system has great potential to achieve this purpose, however, it has not yet been successfully used to efficiently activate endogenous genes and induce changes in cellular phenotype. A powerful method for transcriptional activation by using CRISPR/Cas9 was developed. Replacement of a methylated promoter with an unmethylated one by CRISPR/Cas9 was sufficient to activate the expression of the neural cell gene OLIG2 and the embryonic stem cell gene NANOG in HEK293T cells. Moreover, CRISPR/Cas9-based OLIG2 activation induced the embryonic carcinoma cell line NTERA-2 to express the neuronal marker βIII-tubulin. PMID:27079176

  11. Network compensation for missing sensors

    NASA Technical Reports Server (NTRS)

    Ahumada, Albert J., Jr.; Mulligan, Jeffrey B.

    1991-01-01

    A network learning translation invariance algorithm to compute interpolation functions is presented. This algorithm with one fixed receptive field can construct a linear transformation compensating for gain changes, sensor position jitter, and sensor loss when there are enough remaining sensors to adequately sample the input images. However, when the images are undersampled and complete compensation is not possible, the algorithm need to be modified. For moderate sensor losses, the algorithm works if the transformation weight adjustment is restricted to the weights to output units affected by the loss.

  12. Neutron activation analysis of thermal power plant ash and surrounding area soils.

    PubMed

    Al-Masri, M S; Haddad, Kh; Alsomel, N; Sarhil, A

    2015-08-01

    Elemental concentrations of As, Cd, Co, Cr, Fe, Hg, Mo, Ni, Se, and Zn have been determined in fly and bottom ash collected from Syrian power plants fired by heavy oil and natural gas using instrumental neutron activation analysis. The results showed that all elements were more concentrated in fly ash than in the fly ash; there was a clear increasing trend of the elemental concentrations in the fly ash along the flue gas pathway. The annual emission of elements was estimated. Elemental concentrations were higher inside the campus area than in surrounding areas, and the lowest values were found in natural-gas-fired power plant. In addition, the levels have decreased as the distance from power plant campus increases. However, the levels in the surrounding villages were within the Syrian standard for agriculture soil. PMID:26220782

  13. Inspection of surveillance activities and administrative leave policy at Bonneville Power Administration, Portland, Oregon

    SciTech Connect

    Not Available

    1994-04-01

    The authors conducted an inspection of surveillance activities and administrative leave policy at the Bonneville Power Administration, Portland, Oregon. The purpose of their inspection was to determine if a covert video surveillance operation conducted at Bonneville Power Administration was consistent with Department of Energy policies and procedures and other applicable regulations and procedures, and to determine if administrative leave policies and procedures used at Bonneville Power Administration in a specific instance were consistent with Department of Energy requirements and the Code of Federal Regulations. This inspection focused on a specific incident that occurred in 1989 on the 5th floor of the BPA Headquarters Building located in Portland, Oregon. The incident involved the soiling of an employee`s personal property with what appeared to be urine.

  14. Active local oscillator power stabilization for a hot electron bolometer heterodyne receiver

    NASA Astrophysics Data System (ADS)

    Hayton, D. J.; Gao, J. R.; Kooi, J. W.; Ren, Y.; Zhang, W.; de Lange, G.

    2012-09-01

    We report on the application of a new technique for actively stabilizing the power of a far infrared gas laser as the local oscillator (LO) in a superconducting hot electron bolometer (HEB) heterodyne receiver system at 2.5 THz. The technique utilizes PID feedback control of the local oscillator intensity by means of a voice-coil based swing arm actuator placed in the beam path. The HEB itself is used as a direct detector to measure incident LO power whilst simultaneously continuing to function as heterodyne mixer. Results presented here demonstrate a factor of 50 improvement in the measured total power and spectroscopic Allan variance time. Allan times of 30 seconds and 25 seconds respectively are shown for large and small area HEB's with a measured effective noise fluctuation bandwidth of 12 MHz. The technique is versatile and can be applied to any LO source and at any LO frequency.

  15. Transmutation and activation analysis for divertor materials in a HCLL-type fusion power reactor

    NASA Astrophysics Data System (ADS)

    Fischer, U.; Pereslavtsev, P.; Möslang, A.; Rieth, M.

    2009-04-01

    The activation and transmutation of tungsten and tantalum as plasma facing materials was assessed for a helium cooled divertor irradiated in a typical fusion power reactor based on the use of Helium-cooled Lithium Lead (HCLL) blankets. 3D activation calculations were performed by applying a programme system linking the Monte Carlo transport code MCNP and the fusion inventory code FISPACT through an appropriate interface. Special attention was given to the proper treatment of the resonance shielding of tungsten and tantalum by using reaction rates provided directly by MCNP on the basis of continuous energy activation cross-section data. It was shown that the long-term activation behaviour is dominated by activation products of the assumed tramp material while the short-term behaviour is due to the activation of the stable Ta and W isotopes. The recycling limit for remote handling of 100 mSv/h can be achieved after decay times of 10 and 50 years for Ta and W, respectively. The elemental transmutation rates of Ta and W were shown to be on a moderate level for the HCLL-type fusion power reactor.

  16. More rain compensation results

    NASA Technical Reports Server (NTRS)

    Sworder, D. D.; Vojak, R.

    1992-01-01

    To reduce the impact of rain-induced attenuation in the 20/30 GHz band, the attenuation at a specified signal frequency must be estimated and extrapolated forward in time on the basis of a noisy beacon measurement. Several studies have used model based procedures for solving this problem in statistical inference. Perhaps the most widely used model-based paradigm leads to the Kalman filter and its lineal variants. In this formulation, the dynamic features of the attenuation are represented by a state process (x(sub t)). The observation process (y(sub t)) is derived from beacon measurements. Some ideas relating to the signal processing problems related to uplink power control are presented. It is shown that some easily implemented algorithms hold promise for use in estimating rain induced fades. The algorithms were applied to actual data generated at the Virginia Polytechnic Institute and State University (VPI) test facility. Because only one such event was studied, it is not clear that the algorithms will have the same effectiveness when a wide range of events are studied.

  17. Solutions for stability and astigmatism in high power laser resonators

    NASA Astrophysics Data System (ADS)

    Narro, R.; Arronte, M.; de Posada, E.; Ponce, L.; Rodríguez, E.

    2009-09-01

    A method is proposed for the design of fundamental mode high power resonators, with joined stability zones. A parameter is created which gives the minimum length a laser resonator should have while having at the same time the broadest stabilities zones. For multimode and large mode volume resonators, a configuration is introduced for maximizing the laser overall efficiency due to the compensation of the astigmatism induced by the flash lamp pumping heating. The later configuration proposes a dual-active medium resonator, with 90 degree rotation around the optical axis between the astigmatic thermal lenses of the mediums. The reliability of this configuration is corroborated experimentally using a Nd:YAG dual-active medium resonator. It is found that in the pumping power range where the astigmatism compensation is possible, the overall efficiency is constant, even when increasing the excitation power with the consequent increase of the thermal lens dioptric power.

  18. Atmospheric Compensation for Uplink Arrays via Radiometry

    NASA Technical Reports Server (NTRS)

    Nessel, James A.; Acosta, Roberto J.

    2010-01-01

    Uplink arrays for communications applications are gaining increased visibility within the NASA and military community due to the enhanced flexibility and reliability they provide. When compared with the conventional large, single aperture antennas currently comprising the Deep Space Network (DSN), for example, smaller aperture antenna arrays have the benefits of providing fault tolerance (reduced single-point failure), reduced maintenance cost, and enhanced capabilities such as electronic beam-steering and multi-beam operation. However, signal combining of antenna array elements spaced many wavelengths apart becomes problematic due to the inherent instability of earth's turbulent atmosphere, particularly at the frequencies of interest to the DSN (i.e., Ka-band). Degradation in the power combining of the individual elements comprising the array arises due to uncorrelated phase errors introduced as the signals propagate through the troposphere. It is well known that the fundamental source of this error is due to the inhomogeneous distribution of water vapor in the atmosphere [1]. Several techniques have been proposed to circumvent this issue, including the use of phase calibration towers and a moon bounce to generate a feedback loop which would provide a means of intermittent calibration of the system phase errors (thermal drifts, atmosphere) [2,3]. However, these techniques require repositioning of the antenna elements to perform this operation which ultimately results in reduced system availability. And, though they are sufficient for compensating for slow varying phase drifts, they are insufficient to compensate for faster varying phase errors, such as those introduced by the atmosphere. In this paper, preliminary radiometry and interferometry measurements collected by the NASA Glenn Research Center are analyzed and indicate that the use of optimized water vapor radiometers as a feedback system in a communications platform could provide the necessary atmospheric

  19. Performance Prediction of Active Piezo Fiber Rackets in Terms of Tennis Power

    NASA Astrophysics Data System (ADS)

    Kawazoe, Yoshihiko; Takeda, Yukihiro; Nakagawa, Masamichi

    Several former top players sent a letter to the International Tennis Federation (ITF) encouraging the governing body to revisit the question of rackets. In the letter, the players wrote that racket technology has led to major changes in how the game is played at the top level. This paper investigated the physical properties of a new type of racket with active piezoelectric fibers appeared recently in the market, and predicted the various factors associated with the frontal impact, such as impact force, contact time, deformation of ball and strings, and also estimated the racket performance such as the coefficient of restitution, the rebound power coefficient, the post-impact ball velocity and the sweet areas relevant to the power in tennis. It is based on the experimental identification of the dynamics of the ball-racket-arm system and the approximate nonlinear impact analysis with a simple swing model. The predicted results with forehand stroke model can explain the difference in mechanism of performance between the new type racket with active piezoelectric fibers and the conventional passive representative rackets. It showed that this new type racket provides higher coefficient of restitution on the whole area of string face and also gives larger rebound power coefficients particularly at the topside and bigger powers on the whole area of string face but the difference was not so large. It seems that the racket-related improvements in play are relatively small and the players themselves continue to improve, accordingly there is a gap between a perception and reality.

  20. [From medical complication to compensation for the prejudice].

    PubMed

    Trouiller, P; Lopard, E; Mantz, J; Farman, T

    2012-01-01

    Claims in anesthesia and intensive care remains high, despite the reduction of morbidity and mortality associated with this activity. The absence of a national register makes it difficult to quantify. The Medical Committee of MACSF-Sou Medical Group, professional liability insurer of more than half of French physicians, provided us support. The amount of compensation paid is growing and the scope of compensated damage is expanded by the Dintilhac mission. The Act of March 4, 2002 has fully confirmed the principle of medical liability for misconduct. Generally, compensation for bodily injury is based on the demonstration of a causal link between a wrongful event and injury. The proof of fault lies with the applicant. Information accountable to patients and nosocomial infection are a particular setting. The Act of March 4, 2002 has also defined the concept of therapeutic risk. With the establishment of the Regional Commissions of Conciliation and Compensation (RCCI) and the National Office for Compensation of Medical Accident (Oniam), it is now possible for a patient to be compensated for an injury resulting from an accident Medical non-offending, while acknowledging the lack of accountability of the practitioner. The expertise conducted by an RCCI is adversarial. For the practitioner called to the cause, it is important to prepare for both substance and form, with the assistance of the medical board's insurance company. PMID:22763310

  1. Impact of Inertial Training on Strength and Power Performance in Young Active Men.

    PubMed

    Naczk, Mariusz; Naczk, Alicja; Brzenczek-Owczarzak, Wioletta; Arlet, Jarosław; Adach, Zdzisław

    2016-08-01

    Naczk, M, Naczk, A, Brzenczek-Owczarzak, W, Arlet, J, and Adach, Z. Impact of inertial training on strength and power performance in young active men. J Strength Cond Res 30(8): 2107-2113, 2016-This study evaluated how 5 weeks of inertial training using 2 different loads influenced strength and power performance. Fifty-eight male physical education students were randomly divided into training and control groups. The 2 training groups (T0 and T10) performed inertial training 3 times per week for 5 weeks using the new Inertial Training and Measurement System (ITMS). Each training session included 3 exercise sets involving the knee extensors muscles. The T0 group used only the mass of the ITMS flywheel (19.4 kg), whereas the T10 group had an additional 10 kg on the flywheel. Before and after training, we evaluated maximum force and power of knee extensors muscles, countermovement jump (CMJ), squat jump (SJ), maximal power output achieved during ergometer test PVT, electromyography of quadriceps, and muscle mass. In T0 and T10, respectively, ITMS training induced significant increases in muscle force (25.2 and 23.3%), muscle power (33.2 and 27%), CMJ (3.8 and 6.7%), SJ (2.2 and 6.1%), PVT (8 and 7.4%), and muscle mass (9.8 and 15%). The changes did not significantly differ between T0 and T10. A 16% significant increase of electromyography amplitude (quadriceps muscle) was noted only in T0. The novel ITMS training method is effective for improving muscular strength and power. Improvements in PVT, CMJ, and SJ indicate that the increased strength and power elicited by ITMS training can translate to improvements in sport performance. The ITMS training can also be useful for building muscle mass. PMID:27457914

  2. High-temperature optically activated GaAs power switching for aircraft digital electronic control

    NASA Technical Reports Server (NTRS)

    Berak, J. M.; Grantham, D. H.; Swindal, J. L.; Black, J. F.; Allen, L. B.

    1983-01-01

    Gallium arsenide high-temperature devices were fabricated and assembled into an optically activated pulse-width-modulated power control for a torque motor typical of the kinds used in jet engine actuators. A bipolar heterojunction phototransistor with gallium aluminum arsenide emitter/window, a gallium arsenide junction field-effect power transistor and a gallium arsenide transient protection diode were designed and fabricated. A high-temperature fiber optic/phototransistor coupling scheme was implemented. The devices assembled into the demonstrator were successfully tested at 250 C, proving the feasibility of actuator-located switching of control power using optical signals transmitted by fibers. Assessments of the efficiency and technical merits were made for extension of this high-temperature technology to local conversion of optical power to electrical power and its control at levels useful for driving actuators. Optical power sources included in the comparisons were an infrared light-emitting diode, an injection laser diode, tungsten-halogen lamps and arc lamps. Optical-to-electrical power conversion was limited to photovoltaics located at the actuator. Impedance matching of the photovoltaic array to the load was considered over the full temperature range, -55 C to 260 C. Loss of photovoltaic efficiency at higher temperatures was taken into account. Serious losses in efficiency are: (1) in the optical source and the cooling which they may require in the assumed 125 C ambient, (2) in the decreased conversion efficiency of the gallium arsenide photovoltaic at 260 C, and (3) in impedance matching. Practical systems require improvements in these areas.

  3. Combining Droop Curve Concepts with Control Systems for Wind Turbine Active Power Control: Preprint

    SciTech Connect

    Buckspan, A.; Aho, J.; Pao, L.; Fleming, P.; Jeong, Y.

    2012-06-01

    Wind energy is becoming a larger portion of the global energy portfolio and wind penetration has increased dramatically in certain regions of the world. This increasing wind penetration has driven the need for wind turbines to provide active power control (APC) services to the local utility grid, as wind turbines do not intrinsically provide frequency regulation services that are common with traditional generators. It is common for large scale wind turbines to be decoupled from the utility grid via power electronics, which allows the turbine to synthesize APC commands via control of the generator torque and blade pitch commands. Consequently, the APC services provided by a wind turbine can be more flexible than those provided by conventional generators. This paper focuses on the development and implementation of both static and dynamic droop curves to measure grid frequency and output delta power reference signals to a novel power set point tracking control system. The combined droop curve and power tracking controller is simulated and comparisons are made between simulations using various droop curve parameters and stochastic wind conditions. The tradeoffs involved with aggressive response to frequency events are analyzed. At the turbine level, simulations are performed to analyze induced structural loads. At the grid level, simulations test a wind plant's response to a dip in grid frequency.

  4. Active Vibration Control for Helicopter Interior Noise Reduction Using Power Minimization

    NASA Technical Reports Server (NTRS)

    Mendoza, J.; Chevva, K.; Sun, F.; Blanc, A.; Kim, S. B.

    2014-01-01

    This report describes work performed by United Technologies Research Center (UTRC) for NASA Langley Research Center (LaRC) under Contract NNL11AA06C. The objective of this program is to develop technology to reduce helicopter interior noise resulting from multiple gear meshing frequencies. A novel active vibration control approach called Minimum Actuation Power (MAP) is developed. MAP is an optimal control strategy that minimizes the total input power into a structure by monitoring and varying the input power of controlling sources. MAP control was implemented without explicit knowledge of the phasing and magnitude of the excitation sources by driving the real part of the input power from the controlling sources to zero. It is shown that this occurs when the total mechanical input power from the excitation and controlling sources is a minimum. MAP theory is developed for multiple excitation sources with arbitrary relative phasing for single or multiple discrete frequencies and controlled by a single or multiple controlling sources. Simulations and experimental results demonstrate the feasibility of MAP for structural vibration reduction of a realistic rotorcraft interior structure. MAP control resulted in significant average global vibration reduction of a single frequency and multiple frequency excitations with one controlling actuator. Simulations also demonstrate the potential effectiveness of the observed vibration reductions on interior radiated noise.

  5. New Ideas in Educational Compensation.

    ERIC Educational Resources Information Center

    Rhodes, Eric; Kaplan, Harold

    This report suggests some possibilities open to school boards for improving compensation methods and presents some new avenues of exploration and study for boards wishing to pursue such possibilities. Subjects covered in the report include (1) the concept of accountability, (2) differentiated staffing, (3) merit pay plans, (4) performance…

  6. Can Education Compensate for Society?

    ERIC Educational Resources Information Center

    Pring, Richard

    2011-01-01

    The extent to which education can compensate for social disadvantage is a matter of political controversy, especially in the context of policies for social mobility. On the one hand, to blame poor achievement on social class or poverty was seen to dodge the professional responsibility of teachers. On the other, the strong correlation between…

  7. Concealing compensation from the IRS.

    PubMed

    Burda, D; Greene, J

    1991-01-28

    Tougher reporting requirements from the Internal Revenue Service are prompting some not-for-profit hospitals to seek ways to hide compensation arrangements from the public and the media. Critics believe those tactics could get hospitals in hot water with the law, especially now that the IRS has launched a new, aggressive auditing offensive. PMID:10108763

  8. Merit Compensation and Higher Education.

    ERIC Educational Resources Information Center

    Counelis, James Steve

    The concept of merit compensation is clarified from both administrative and faculty perspectives, and the conceptual sources of the controversy surrounding "merit" are addressed. Using the lexical tradition of the verb "to merit," four distinct semantic components are identified: to earn, to deserve, to value or give preference, and to obtain…

  9. 78 FR 28441 - Executive Compensation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-14

    ... level or range of compensation. \\11\\ For example, the financial crisis of 2008 caused Congress to enact...-- Interim Final Rule with Request for Comments, 73 FR 53356 (September 16, 2008), with Correcting Amendments at 73 FR 54309 (September 19, 2008) and 73 FR 54673 (September 23, 2008), codified at 12 CFR...

  10. Clarification of Workmen's Compensation Insurance.

    ERIC Educational Resources Information Center

    Shapley, Allen E.

    This document attempts to answer questions resulting from the 1972 Michigan Supreme Court Ruling relative to agricultural employees under the Workmen's Compensation Act (WCA). The sections of this paper outline a history of the WCA; employers covered; definition of "regularly employ"; clarification of "thirteen weeks"; employees (minors, partners,…

  11. CFO compensation reaches record levels.

    PubMed

    2001-06-01

    HFMA's 2001 CFO compensation survey finds that CFOs of hospitals and health systems are receiving higher compensation today than ever before. The current average compensation of $127,00--15.5 percent higher than was reported in a similar survey conducted in 1999--is the highest ever recorded by HFMA. Moreover, comparison of the 2001 findings with results of previous surveys shows that the earnings gains for CFOs over the past two years are stronger than they have been at many times in recent history. Factors that were found to influence CFO compensation in 2001 are location, years of service, number of employees reporting to the CFO, supervisory responsibility at the system versus hospital level, experience, and gender. Significant findings of the survey were that the average earnings of CFOs in urban areas are nearly twice those of CFOs in rural areas and that the average difference between earnings of male and female CFOs narrowed from $45,100 in 1999 to $36,800 in 2001. PMID:11407122

  12. Management Compensation: A Progress Report.

    ERIC Educational Resources Information Center

    Ramstad, Bill; And Others

    This examination of the current status of compensation for community college management and administrative personnel first summarizes the findings of a study conducted by Howard R. Bowen, which determined that, compared to business executives in comparable jobs within organizations of similar sizes, academic administrators were indeed underpaid.…

  13. Synchrony - Cyberknife Respiratory Compensation Technology

    SciTech Connect

    Ozhasoglu, Cihat Saw, Cheng B.; Chen Hungcheng; Burton, Steven; Komanduri, Krishna; Yue, Ning J.; Huq, Saiful M.; Heron, Dwight E.

    2008-07-01

    Studies of organs in the thorax and abdomen have shown that these organs can move as much as 40 mm due to respiratory motion. Without compensation for this motion during the course of external beam radiation therapy, the dose coverage to target may be compromised. On the other hand, if compensation of this motion is by expansion of the margin around the target, a significant volume of normal tissue may be unnecessarily irradiated. In hypofractionated regimens, the issue of respiratory compensation becomes an important factor and is critical in single-fraction extracranial radiosurgery applications. CyberKnife is an image-guided radiosurgery system that consists of a 6-MV LINAC mounted to a robotic arm coupled through a control loop to a digital diagnostic x-ray imaging system. The robotic arm can point the beam anywhere in space with 6 degrees of freedom, without being constrained to a conventional isocenter. The CyberKnife has been recently upgraded with a real-time respiratory tracking and compensation system called Synchrony. Using external markers in conjunction with diagnostic x-ray images, Synchrony helps guide the robotic arm to move the radiation beam in real time such that the beam always remains aligned with the target. With the aid of Synchrony, the tumor motion can be tracked in three-dimensional space, and the motion-induced dosimetric change to target can be minimized with a limited margin. The working principles, advantages, limitations, and our clinical experience with this new technology will be discussed.

  14. Compensation for oil pollution damage

    NASA Astrophysics Data System (ADS)

    Matugina, E. G.; Glyzina, T. S.; Kolbysheva, Yu V.; Klyuchnikov, A. S.; Vusovich, O. V.

    2015-11-01

    The commitment of national industries to traditional energy sources, as well as constantly growing energy demand combined with adverse environmental impact of petroleum production and transportation urge to establish and maintain an appropriate legal and administrative framework for oil pollution damage compensation. The article considers management strategies for petroleum companies that embrace not only production benefits but also environmental issues.

  15. Strategic Design of Teacher Compensation

    ERIC Educational Resources Information Center

    Shields, Regis

    2012-01-01

    Spurred by the national focus on revitalizing the teacher evaluation and support/development process, as well as the current economic downturn, many school districts are reviewing how teachers are compensated. While a few courageous districts have completely upended current structures, most districts are undertaking changes that leave the most…

  16. Annual Pay and Compensation Report.

    ERIC Educational Resources Information Center

    Vocino, Joe

    2003-01-01

    Presents results of the 2002 Human Resource Management Compensation Survey (n=1,084) indicating that salaries for training and development professionals increased only 1.8 percent over 2001. Tables depict salaries at various levels, by geographic area, and by industry. (JOW)

  17. Altitude Compensating Nozzle Concepts Evaluation

    NASA Technical Reports Server (NTRS)

    Soni, Bharat

    2000-01-01

    This report contains the summary of work accomplished during summer of 2000 by Mr. Chad Hammons, undergraduate senior student, Mississippi State University/ERC in support of NASA/MSFC mission pertinent to Altitude compensating nozzle concepts evaluations. In particular, the development of automatic grid generator applicable in conducting sensitivity analysis involving Aerospike engine is described.

  18. How to Treat Compensated Absences.

    ERIC Educational Resources Information Center

    Lewandowski, Raymond J.

    1986-01-01

    Discusses compensated absences such as future vacation, sick leave, and other absences that must be recognized for accounting and financial reporting purposes. Explains Governmental Accounting Standards Board distinctions between governmental and proprietary fund models. School districts and municipalities must now account for compensated…

  19. The Role of Power Doppler Ultrasonography as Disease Activity Marker in Rheumatoid Arthritis

    PubMed Central

    Bhasin, Shaloo; Cheung, Peter P.

    2015-01-01

    Structural damage in rheumatoid arthritis (RA) occurs early if inflammation is not treated promptly. Treatment targeted to reduce inflammation, in particular, that of synovial inflammation in the joints (synovitis), has been recommended as standard treat-to-target recommendations by rheumatologists. The goal is to achieve disease remission (i.e., no disease activity). Several accepted remission criteria have not always equated to the complete absence of true inflammation. Over the last decade, musculoskeletal ultrasonography has been demonstrated to detect subclinical synovitis not appreciated by routine clinical or laboratory assessments, with the Power Doppler modality allowing clinicians to more readily appreciate true inflammation. Thus, targeting therapy to Power Doppler activity may provide superior outcomes compared with treating to clinical targets alone, making it an attractive marker of disease activity in RA. However, more validation on its true benefits such as its benefits to patients in regard to patient related outcomes and issues with standardized training in acquisition and interpretation of power Doppler findings are required. PMID:26063952

  20. Passive and Active Protective Clothing against High-Power Laser Radiation

    NASA Astrophysics Data System (ADS)

    Hennigs, C.; Hustedt, M.; Kaierle, S.; Wenzel, D.; Markstein, S.; Hutter, A.

    The main objective of the work described in this paper was the development of passive and active protective clothing for the protection of the human skin against accidental laser irradiation and of active protective curtains. Here, the passive systems consist of functional multi-layer textiles, providing a high level of passive laser resistance. In addition, the active functional multi-layer textiles incorporate sensors that detect laser exposure and are, by means of a safety control, able to deactivate the laser beam automatically.Due to the lack of regulations for testing and qualifying textiles to be used as laser PPE, test methods were defined and validated. Additionally, corresponding testing set-ups were developed.Finally, the gap with respect to standardization was bridged by the definition of a test procedure and the requirements with respect to laser PPE.The developments were demonstrated by a set of tailored functional passive and active laser-protective clothing prototypes (gloves, jackets, aprons, trousers) and active curtains as well as by a prototype testing rig, providing the possibility to perform the specified low-power and high-power textile test procedure.

  1. Input filter compensation for switching regulators

    NASA Technical Reports Server (NTRS)

    Kelkar, S. S.; Lee, F. C.

    1983-01-01

    A novel input filter compensation scheme for a buck regulator that eliminates the interaction between the input filter output impedance and the regulator control loop is presented. The scheme is implemented using a feedforward loop that senses the input filter state variables and uses this information to modulate the duty cycle signal. The feedforward design process presented is seen to be straightforward and the feedforward easy to implement. Extensive experimental data supported by analytical results show that significant performance improvement is achieved with the use of feedforward in the following performance categories: loop stability, audiosusceptibility, output impedance and transient response. The use of feedforward results in isolating the switching regulator from its power source thus eliminating all interaction between the regulator and equipment upstream. In addition the use of feedforward removes some of the input filter design constraints and makes the input filter design process simpler thus making it possible to optimize the input filter. The concept of feedforward compensation can also be extended to other types of switching regulators.

  2. Ion Behavior in an Electrically Compensated Ion Cyclotron Resonance Trap

    PubMed Central

    Brustkern, Adam M.; Rempel, Don L.; Gross, Michael L.

    2010-01-01

    We recently described a new electrically compensated trap in FT ion cyclotron resonance mass spectrometry and developed a means of tuning traps of this general design. Here, we describe a continuation of that research by comparing the ion transient lifetimes and the resulting mass resolving powers and signal-to-noise (S/N) ratios that are achievable in the compensated vs. uncompensated modes of this trap. Transient lifetimes are ten times longer under the same conditions of pressure, providing improved mass resolving power and S/N ratios. The mass resolving power as a function of m/z is linear (log-log plot) and nearly equal to the theoretical maximum. Importantly, the ion cyclotron frequency as a function of ion number decreases linearly in accord with theory, unlike its behavior in the uncompensated mode. This linearity should lead to better control in mass calibration and increased mass accuracy than achievable in the uncompensated mode. PMID:21499521

  3. The physics of power systems operation

    NASA Astrophysics Data System (ADS)

    Ohler, C.

    2015-08-01

    The article explains the operation of power systems from the point of view of physics. Physicists imagine things, rather than in terms of impedances and circuits, in terms of fields and energy conversions. The account is concrete and simple. The use of alternating current entails the issue of reactive power. Reactive power consists of energy that oscillates between electrical and magnetic fields, it flows on top of the active power which carries the useful energy. The control of active and reactive power is essential for the power system's reliable operation. The frequency of a power system is the same everywhere. The stability of the frequency indicates that generation and demand of active power are equal, a decline in frequency indicates a lack of generation relative to the demand. Adapting the electrical power injected into the system is the way of frequency control. Because of the parasitic inductances and capacitances of overhead lines, cables, and transformers, the voltage at different locations of the power system depends on the load. The voltage is regulated by the combined action of generator excitation, transformer tap changers and series compensation in order to provide consumers with a stable voltage supply. The integration of solar cells and wind turbines into the power system poses some challenges. But the power system is able to accommodate large amounts of fluctuating renewable power generation if the right complementary measures are taken.

  4. Workers' Compensation and return-to-work in low back pain.

    PubMed

    Gallagher, R M; Williams, R A; Skelly, J; Haugh, L D; Rauh, V; Milhous, R; Frymoyer, J

    1995-05-01

    The relationship of Workers' Compensation and litigation to low back pain (LBP) outcome is not established in the literature. Our study investigated the characteristics of disabled persons applying for Worker's Compensation or employing a lawyer, the factors predicting receipt of compensation, and the effects of compensation and litigation on employment outcome. One hundred sixty-nine unemployed persons with LBP were assessed by medical history, physical exam, biomechanical testing, psychiatric interview, and MMPI. Subjects were asked whether they had applied for compensation, received it, or had employed a lawyer. Six months later, subjects were asked about their employment and compensation status. Neither compensation status nor involvement of a lawyer significantly improved prediction of employment status 6 months later. Receipt of compensation predicted better outcome in those at risk for poor outcome due to external locus of control. Factors predicting failure to obtain compensation over 6 months, having applied, include education, spinal flexion, ability to do daily activities and affective inhibition. Neurological dysfunction did not predict receipt of compensation in univariate or multivariate analyses; emotional distress reduced the probability of receiving compensation, after controlling for severity of spinal dysfunction. Receipt of compensation and use of a lawyer did not reduce the probability of RTW in disabled persons in the present sample, but increased the likelihood of return to work for groups of individuals at higher risk such as those with external locus of control. Although compensation is awarded on the basis of physical evaluation under the present system, the present findings suggest that the likelihood of receiving compensation is also significantly determined by level of emotional distress. PMID:7659441

  5. Dynamic Simulation of EAF on RTDS for Compensation Sizing

    NASA Astrophysics Data System (ADS)

    Meera, K. S.

    2016-06-01

    Large sized electric arc furnaces (EAF) causes power quality problems such as flicker, harmonics etc. due to their unbalanced and non-linear behavior characteristics. The rapid swings in real and reactive power of such non-linear loads causes fast repetitive voltage variations with appreciable voltage distortion caused by harmonics and unbalance. Some form of reactive compensation is usually adopted to limit the disturbances caused by EAF in electric power system, in particular the flicker. This paper highlights the results of a case study, where the arc furnace is modelled using statistical dynamic model of the furnace using real time digital simulator which allows more real time simulations tests to be conducted in a shorter time and also provides a more detailed power system representation for the tests. The investigation of the simulation study results showed that static VAR compensators can be successfully used for reduction of flicker levels, compensation of reactive power and for the regulation of voltage levels in the EAF plant under study.

  6. Effects of submaximal activation on the determinants of power of chemically skinned rat soleus fibres.

    PubMed

    Gilliver, S F; Degens, H; Rittweger, J; Jones, D A

    2011-02-01

    Reducing the activating calcium concentration with skinned fibres is known to decrease isometric force and maximal shortening velocity, both of which will reduce the peak power. However, power is also a function of the curvature of the force-velocity relationship, and there is limited information on how changes in activating calcium affect this important property of muscle fibres. Force-velocity relationships of permeabilized single type I fibres from rat soleus muscle were determined using isotonic contractions at 15°C with both maximal (pCa 4.5) and submaximal activation (pCa 5.6). The rate of tension redevelopment (k(tr)), which provides a measure of sum of the apparent rate constants for cross-bridge attachment and detachment (f(app) + g(app)) following a rapid release and restretch, was also measured. Compared with pCa 4.5, specific tension (P(o)) at pCa 5.6 declined by 22 ± 8% (mean ± s.d.) and the maximal velocity of shortening (V(max)) fell by 44 ± 7%, but curvature of the force-velocity relationship (a/P(o)) rose by 47 ± 31%, indicating a less concave relationship. The value of k(tr) declined by 23 ± 7%. The change in a/P(o) reduced the impact of changes in P(o) and V(max) on peak power by approximately 25%. Fitting the data to Huxley's model of cross-bridge action suggests that lower activating calcium decreased both the rate constant for cross-bridge attachment (f) and that for detachment of negatively strained cross-bridges (g(2)). The fact that V(max) (and thus g(2)) changed to a greater extent than k(tr) (f(app) + g(app)) is the reason that reduced activation results in a reduction in curvature of the force-velocity relationship. PMID:20889604

  7. A new balancing three level three dimensional space vector modulation strategy for three level neutral point clamped four leg inverter based shunt active power filter controlling by nonlinear back stepping controllers.

    PubMed

    Chebabhi, Ali; Fellah, Mohammed Karim; Kessal, Abdelhalim; Benkhoris, Mohamed F

    2016-07-01

    In this paper is proposed a new balancing three-level three dimensional space vector modulation (B3L-3DSVM) strategy which uses a redundant voltage vectors to realize precise control and high-performance for a three phase three-level four-leg neutral point clamped (NPC) inverter based Shunt Active Power Filter (SAPF) for eliminate the source currents harmonics, reduce the magnitude of neutral wire current (eliminate the zero-sequence current produced by single-phase nonlinear loads), and to compensate the reactive power in the three-phase four-wire electrical networks. This strategy is proposed in order to gate switching pulses generation, dc bus voltage capacitors balancing (conserve equal voltage of the two dc bus capacitors), and to switching frequency reduced and fixed of inverter switches in same times. A Nonlinear Back Stepping Controllers (NBSC) are used for regulated the dc bus voltage capacitors and the SAPF injected currents to robustness, stabilizing the system and to improve the response and to eliminate the overshoot and undershoot of traditional PI (Proportional-Integral). Conventional three-level three dimensional space vector modulation (C3L-3DSVM) and B3L-3DSVM are calculated and compared in terms of error between the two dc bus voltage capacitors, SAPF output voltages and THDv, THDi of source currents, magnitude of source neutral wire current, and the reactive power compensation under unbalanced single phase nonlinear loads. The success, robustness, and the effectiveness of the proposed control strategies are demonstrated through simulation using Sim Power Systems and S-Function of MATLAB/SIMULINK. PMID:27018144

  8. Adaptive filter design based on the LMS algorithm for delay elimination in TCR/FC compensators.

    PubMed

    Hooshmand, Rahmat Allah; Torabian Esfahani, Mahdi

    2011-04-01

    Thyristor controlled reactor with fixed capacitor (TCR/FC) compensators have the capability of compensating reactive power and improving power quality phenomena. Delay in the response of such compensators degrades their performance. In this paper, a new method based on adaptive filters (AF) is proposed in order to eliminate delay and increase the response of the TCR compensator. The algorithm designed for the adaptive filters is performed based on the least mean square (LMS) algorithm. In this design, instead of fixed capacitors, band-pass LC filters are used. To evaluate the filter, a TCR/FC compensator was used for nonlinear and time varying loads of electric arc furnaces (EAFs). These loads caused occurrence of power quality phenomena in the supplying system, such as voltage fluctuation and flicker, odd and even harmonics and unbalancing in voltage and current. The above design was implemented in a realistic system model of a steel complex. The simulation results show that applying the proposed control in the TCR/FC compensator efficiently eliminated delay in the response and improved the performance of the compensator in the power system. PMID:21193194

  9. The effect of precision and power grips on activations in human auditory cortex.

    PubMed

    Wikman, Patrik A; Vainio, Lari; Rinne, Teemu

    2015-01-01

    The neuroanatomical pathways interconnecting auditory and motor cortices play a key role in current models of human auditory cortex (AC). Evidently, auditory-motor interaction is important in speech and music production, but the significance of these cortical pathways in other auditory processing is not well known. We investigated the general effects of motor responding on AC activations to sounds during auditory and visual tasks (motor regions were not imaged). During all task blocks, subjects detected targets in the designated modality, reported the relative number of targets at the end of the block, and ignored the stimuli presented in the opposite modality. In each block, they were also instructed to respond to targets either using a precision grip, power grip, or to give no overt target responses. We found that motor responding strongly modulated AC activations. First, during both visual and auditory tasks, activations in widespread regions of AC decreased when subjects made precision and power grip responses to targets. Second, activations in AC were modulated by grip type during the auditory but not during the visual task. Further, the motor effects were distinct from the present strong attention-related modulations in AC. These results are consistent with the idea that operations in AC are shaped by its connections with motor cortical regions. PMID:26528121

  10. The effect of precision and power grips on activations in human auditory cortex

    PubMed Central

    Wikman, Patrik A.; Vainio, Lari; Rinne, Teemu

    2015-01-01

    The neuroanatomical pathways interconnecting auditory and motor cortices play a key role in current models of human auditory cortex (AC). Evidently, auditory-motor interaction is important in speech and music production, but the significance of these cortical pathways in other auditory processing is not well known. We investigated the general effects of motor responding on AC activations to sounds during auditory and visual tasks (motor regions were not imaged). During all task blocks, subjects detected targets in the designated modality, reported the relative number of targets at the end of the block, and ignored the stimuli presented in the opposite modality. In each block, they were also instructed to respond to targets either using a precision grip, power grip, or to give no overt target responses. We found that motor responding strongly modulated AC activations. First, during both visual and auditory tasks, activations in widespread regions of AC decreased when subjects made precision and power grip responses to targets. Second, activations in AC were modulated by grip type during the auditory but not during the visual task. Further, the motor effects were distinct from the present strong attention-related modulations in AC. These results are consistent with the idea that operations in AC are shaped by its connections with motor cortical regions. PMID:26528121

  11. Object individuation and compensation in healthy aging.

    PubMed

    Pagano, Silvia; Fait, Elisa; Brignani, Debora; Mazza, Veronica

    2016-04-01

    Theories on neural compensation suggest that aged participants overactivate the brain areas involved in a task to compensate for the age-related decline. In this electrophysiological study, we investigated the temporal locus of neural overactivation in aging during multiple target processing. We measured performance and three event-related brain potential responses (N1, N2pc, and contralateral delay activity) in young and old adults, while they enumerated a variable number (1-4) of targets presented in an easy (distractor absent) or difficult (distractor present) condition. The main results indicated that although N2pc (∼200 ms) increased in amplitude in the distractor-present condition in the young group, no modulation occurred for the old group. Old participants were associated with larger N2pc amplitudes than young participants in the distractor-absent condition, where both groups had comparable levels of accuracy. These effects were not present for N1 and contralateral delay activity. Overall, the data suggest that in enumeration, aging is associated with compensatory effects that rely on the selection mechanism responsible for target individuation. PMID:26973114

  12. The discrete-time compensated Kalman filter

    NASA Technical Reports Server (NTRS)

    Lee, W. H.; Athans, M.

    1978-01-01

    A suboptimal dynamic compensator to be used in conjunction with the ordinary discrete time Kalman filter was derived. The resultant compensated Kalman Filter has the property that steady state bias estimation errors, resulting from modelling errors, were eliminated.

  13. Temperature compensation for miniaturized magnetic sector

    NASA Technical Reports Server (NTRS)

    Sinha, Mahadeva P. (Inventor)

    2002-01-01

    Temperature compensation for a magnetic sector used in mass spectrometry. A high temperature dependant magnetic sector is used. This magnetic sector is compensated by a magnetic shunt that has opposite temperature characteristics to those of the magnet.

  14. 75 FR 22679 - Sound Incentive Compensation Guidance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-29

    ... incentive compensation practices in the banking industry by providing a common prudential foundation for incentive compensation arrangements across banking organizations and promoting the overall movement of the industry towards better practices. Supervisory action could play a critical role in addressing...

  15. 75 FR 76079 - Sound Incentive Compensation Guidance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-07

    ... incentive compensation practices in the banking industry by providing a common prudential foundation for incentive compensation arrangements across banking organizations and promoting the overall movement of the industry towards better practices. Supervisory action could play a critical role in addressing...

  16. 75 FR 53023 - Sound Incentive Compensation Guidance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-30

    ... incentive compensation practices in the banking industry by providing a common prudential foundation for incentive compensation arrangements across banking organizations and promoting the overall movement of the industry towards better practices. Supervisory action could play a critical role in addressing...

  17. Illumination control apparatus for compensating solar light

    NASA Technical Reports Server (NTRS)

    Owens, L. J. (Inventor)

    1978-01-01

    An illumination control apparatus is presented for supplementing light from solar radiation with light from an artificial light source to compensate for periods of insufficient levels of solar light. The apparatus maintains a desired illumination level within an interior space comprising an artificial light source connected to an electrical power source with a switch means for selectively energizing said light source. An actuator means for controlling the on-off operation of the switch means is connected to a light sensor which responses to the illumination level of the interior space. A limit switch carried adjacent to the actuator limits the movement of the actuator within a predetermined range so as to prevent further movement thereof during detection of erroneous illumination conditions.

  18. Transparent Stretchable Self-Powered Patchable Sensor Platform with Ultrasensitive Recognition of Human Activities.

    PubMed

    Hwang, Byeong-Ung; Lee, Ju-Hyuck; Trung, Tran Quang; Roh, Eun; Kim, Do-Il; Kim, Sang-Woo; Lee, Nae-Eung

    2015-09-22

    Monitoring of human activities can provide clinically relevant information pertaining to disease diagnostics, preventive medicine, care for patients with chronic diseases, rehabilitation, and prosthetics. The recognition of strains on human skin, induced by subtle movements of muscles in the internal organs, such as the esophagus and trachea, and the motion of joints, was demonstrated using a self-powered patchable strain sensor platform, composed on multifunctional nanocomposites of low-density silver nanowires with a conductive elastomer of poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/polyurethane, with high sensitivity, stretchability, and optical transparency. The ultra-low-power consumption of the sensor, integrated with both a supercapacitor and a triboelectric nanogenerator into a single transparent stretchable platform based on the same nanocomposites, results in a self-powered monitoring system for skin strain. The capability of the sensor to recognize a wide range of strain on skin has the potential for use in new areas of invisible stretchable electronics for human monitoring. A new type of transparent, stretchable, and ultrasensitive strain sensor based on a AgNW/PEDOT:PSS/PU nanocomposite was developed. The concept of a self-powered patchable sensor system integrated with a supercapacitor and a triboelectric nanogenerator that can be used universally as an autonomous invisible sensor system was used to detect the wide range of strain on human skin. PMID:26277994

  19. Fission-activated laser as primary power for CW laser propulsion

    SciTech Connect

    Monroe, D.K.

    1994-12-31

    Recent advances in the development of reactor-pumped lasers (RPL`s) have stimulated renewed interest in the concept of laser-powered propulsion. This paper surveys a number of laser propulsion concepts and identifies the one that is most promising from the standpoint of practicality. It is proposed that a ground-based FALCON (Fission-Activated Laser CONcept) RPL can provide primary power for this launch vehicle design. The laser-vehicle system could launch small payloads into low-earth orbit (LEO) with high repetition rates and at low costs per kilogram. For the favored design, thruster efficiencies are currently estimated to be about 500%, with 800% being seen as a potentially realizable goal after further design refinements. Laser launch system simulations indicate that, with a buy-in laser power of 10 MW, it will be possible to obtain specific impulses in the range of 600 to 800 seconds and payload-to-power ratios of 1 to 3 kg/MW.

  20. Harmonic and power factor correction by means of active line conditioners with adaptive estimation control

    SciTech Connect

    Ashton, R.W.

    1991-01-01

    Due to the proliferation of power electronic devices in recent years, the amount of harmonic current injected into power systems is on the increase causing undesirable voltage waveform distortion. A new type of versatile Active Power Line Conditioner able to supply a DC load while generating useful harmonics which help reduce the voltage distortion at the connected bus was designed, built and analyzed. The optimum design was obtained by means of an economic study that considers the power loss, the cost of an RFI filter and the effect of the switching rate. An adaptive methodology, requiring only knowledge of the bus voltage distortion, was developed and applied to adjust the amplitudes and phase angles of the injected harmonic currents. This novel approach is based on reducing the voltage Total Harmonic Distortion by minimizing the individual harmonic voltages in an error signal using a gradient method. Through successive adjustments, the difference between the actual bus voltage and the desired bus voltage is minimized. The proposed method can be successfully applied in low and medium voltage networks with multiple nonlinear loads scattered among linear loads.