Imbalance detection in a manufacturing system: An agent-based model usage

NASA Astrophysics Data System (ADS)

Shevchuk, G. K.; Zvereva, O. M.; Medvedev, M. A.

2017-11-01

This paper delivers the results of the research work targeted at communications in a manufacturing system. A computer agent-based model which simulates manufacturing system functioning has been engineered. The system lifecycle consists of two recursively repeated stages: a communication stage and a production stage. Model data sets were estimated with the static Leontief's equilibrium equation usage. In experiments relationships between the manufacturing system lifecycle time and conditions of equilibrium violations have been identified. The research results are to be used to propose violation negative influence compensation methods.

Lifecycle Analysis of Different Motors from the Standpoint of Environmental Impact

NASA Astrophysics Data System (ADS)

Orlova, S.; Rassõlkin, A.; Kallaste, A.; Vaimann, T.; Belahcen, A.

2016-12-01

Comparative analysis is performed for different motors from the standpoint of damage inflicted by them during their lifecycle. Three types of motors have been considered: the synchronous reluctance motor, the permanent magnet assisted synchronous reluctance motor and the induction motor. The assessment of lifecycle has been made in terms of its four stages: manufacturing, distribution, use and end of life. The results show that the production costs of synchronous reluctance motor are lower compared to that of permanent magnet assisted motors, but due to their low efficiency they exert the greatest environmental impact. The main conclusion is that the assessment made at the early designing stage for the related environmental impact enables its reduction.

The biogeography of the atlantic salmon (Salmo salar) gut microbiome.

PubMed

Llewellyn, Martin S; McGinnity, Philip; Dionne, Melanie; Letourneau, Justine; Thonier, Florian; Carvalho, Gary R; Creer, Simon; Derome, Nicolas

2016-05-01

Although understood in many vertebrate systems, the natural diversity of host-associated microbiota has been little studied in teleosts. For migratory fishes, successful exploitation of multiple habitats may affect and be affected by the composition of the intestinal microbiome. We collected 96 Salmo salar from across the Atlantic encompassing both freshwater and marine phases. Dramatic differences between environmental and gut bacterial communities were observed. Furthermore, community composition was not significantly impacted by geography. Instead life-cycle stage strongly defined both the diversity and identity of microbial assemblages in the gut, with evidence for community destabilisation in migratory phases. Mycoplasmataceae phylotypes were abundantly recovered in all life-cycle stages. Patterns of Mycoplasmataceae phylotype recruitment to the intestinal microbial community among sites and life-cycle stages support a dual role for deterministic and stochastic processes in defining the composition of the S. salar gut microbiome.

The biogeography of the atlantic salmon (Salmo salar) gut microbiome

PubMed Central

Llewellyn, Martin S; McGinnity, Philip; Dionne, Melanie; Letourneau, Justine; Thonier, Florian; Carvalho, Gary R; Creer, Simon; Derome, Nicolas

2016-01-01

Although understood in many vertebrate systems, the natural diversity of host-associated microbiota has been little studied in teleosts. For migratory fishes, successful exploitation of multiple habitats may affect and be affected by the composition of the intestinal microbiome. We collected 96 Salmo salar from across the Atlantic encompassing both freshwater and marine phases. Dramatic differences between environmental and gut bacterial communities were observed. Furthermore, community composition was not significantly impacted by geography. Instead life-cycle stage strongly defined both the diversity and identity of microbial assemblages in the gut, with evidence for community destabilisation in migratory phases. Mycoplasmataceae phylotypes were abundantly recovered in all life-cycle stages. Patterns of Mycoplasmataceae phylotype recruitment to the intestinal microbial community among sites and life-cycle stages support a dual role for deterministic and stochastic processes in defining the composition of the S. salar gut microbiome. PMID:26517698

Life-history stages of natural bloom populations and the bloom dynamics of a tropical Asian ribotype of Alexandrium minutum.

PubMed

Lau, Winnie Lik Sing; Law, Ing Kuo; Liow, Guat Ru; Hii, Kieng Soon; Usup, Gires; Lim, Po Teen; Leaw, Chui Pin

2017-12-01

In 2015, a remarkably high density bloom of Alexandrium minutum occurred in Sungai Geting, a semi-enclosed lagoon situated in the northeast of Peninsular Malaysia, causing severe discoloration and contaminated the benthic clams (Polymesoda). Plankton and water samples were collected to investigate the mechanisms of bloom development of this toxic species. Analysis of bloom samples using flow cytometry indicated that the bloom was initiated by the process of active excystment, as planomycetes (>4C cells) were observed in the early stage of the bloom. Increase in planozygotes (2C cells) was evident during the middle stage of the bloom, coinciding with an abrupt decrease in salinity and increase of temperature. The bloom was sustained through the combination of binary division of vegetative cells, division of planozygotes, and cyst germination through continuous excystment. Nutrient depletion followed by precipitation subsequently caused the bloom to terminate. This study provides the first continuous record of in situ life-cycle stages of a natural bloom population of A. minutum through a complete bloom cycle. The event has provided a fundamental understanding of the pelagic life-cycle stages of this tropical dinoflagellate, and demonstrated a unique bloom development characteristic shared among toxic Alexandrium species in coastal embayments. Copyright © 2017 Elsevier B.V. All rights reserved.

Enriching step-based product information models to support product life-cycle activities

NASA Astrophysics Data System (ADS)

Sarigecili, Mehmet Ilteris

The representation and management of product information in its life-cycle requires standardized data exchange protocols. Standard for Exchange of Product Model Data (STEP) is such a standard that has been used widely by the industries. Even though STEP-based product models are well defined and syntactically correct, populating product data according to these models is not easy because they are too big and disorganized. Data exchange specifications (DEXs) and templates provide re-organized information models required in data exchange of specific activities for various businesses. DEXs show us it would be possible to organize STEP-based product models in order to support different engineering activities at various stages of product life-cycle. In this study, STEP-based models are enriched and organized to support two engineering activities: materials information declaration and tolerance analysis. Due to new environmental regulations, the substance and materials information in products have to be screened closely by manufacturing industries. This requires a fast, unambiguous and complete product information exchange between the members of a supply chain. Tolerance analysis activity, on the other hand, is used to verify the functional requirements of an assembly considering the worst case (i.e., maximum and minimum) conditions for the part/assembly dimensions. Another issue with STEP-based product models is that the semantics of product data are represented implicitly. Hence, it is difficult to interpret the semantics of data for different product life-cycle phases for various application domains. OntoSTEP, developed at NIST, provides semantically enriched product models in OWL. In this thesis, we would like to present how to interpret the GD & T specifications in STEP for tolerance analysis by utilizing OntoSTEP.

[A Medical Devices Management Information System Supporting Full Life-Cycle Process Management].

PubMed

Tang, Guoping; Hu, Liang

2015-07-01

Medical equipments are essential supplies to carry out medical work. How to ensure the safety and reliability of the medical equipments in diagnosis, and reduce procurement and maintenance costs is a topic of concern to everyone. In this paper, product lifecycle management (PLM) and enterprise resource planning (ERP) are cited to establish a lifecycle management information system. Through integrative and analysis of the various stages of the relevant data in life-cycle, it can ensure safety and reliability of medical equipments in the operation and provide the convincing data for meticulous management.

The lifecycle of e-learning course in the adaptive educational environment

NASA Astrophysics Data System (ADS)

Gustun, O. N.; Budaragin, N. V.

2017-01-01

In the article we have considered the lifecycle model of the e-learning course in the electronic educational environment. This model consists of three stages and nine phases. In order to implement the adaptive control of the learning process we have determined the actions which are necessary to undertake at different phases of the e-learning course lifecycle. The general characteristics of the SPACEL-technology is given for creating adaptive educational environments of the next generation.

Partial Life-Cycle and Acute Toxicity of Perfluoroalkyl Acids to Freshwater Mussels

EPA Science Inventory

Freshwater mussels are among the most sensitive aquatic organisms to many contaminants and have complex life-cycles that include several distinct life stages with unique contaminant exposure pathways. Standard acute (24–96 h) and chronic (28 d) toxicity tests with free larva (glo...

The Influence of Socializing Agents in the Female Sport-Participation Process.

ERIC Educational Resources Information Center

Higginson, David C.

1985-01-01

Investigated the influence of socializing agents on female athletes (N=587). Made comparisons across life-cycle states and discovered that socializing agent influences changed from being mostly parental at the under-13 life-cycle stage to mostly coach/teacher-oriented during junior and senior high school years. (BH)

The Chicago Center for Green Technology: life-cycle assessment of a brownfield redevelopment project

NASA Astrophysics Data System (ADS)

Brecheisen, Thomas; Theis, Thomas

2013-03-01

The sustainable development of brownfields reflects a fundamental, yet logical, shift in thinking and policymaking regarding pollution prevention. Life-cycle assessment (LCA) is a tool that can be used to assist in determining the conformity of brownfield development projects to the sustainability paradigm. LCA was applied to the process of a real brownfield redevelopment project, now known as the Chicago Center for Green Technology, to determine the cumulative energy required to complete the following redevelopment stages: (1) brownfield assessment and remediation, (2) building rehabilitation and site development and (3) ten years of operation. The results of the LCA have shown that operational energy is the dominant life-cycle stage after ten years of operation. The preservation and rehabilitation of the existing building, the installation of renewable energy systems (geothermal and photovoltaic) on-site and the use of more sustainable building products resulted in 72 terajoules (TJ) of avoided energy impacts, which would provide 14 years of operational energy for the site. Methodological note: data for this life-cycle assessment were obtained from project reports, construction blueprints and utility bills.

Modeling the influence of genetic and environmental variation on the expression of plant life cycles across landscapes.

PubMed

Burghardt, Liana T; Metcalf, C Jessica E; Wilczek, Amity M; Schmitt, Johanna; Donohue, Kathleen

2015-02-01

Organisms develop through multiple life stages that differ in environmental tolerances. The seasonal timing, or phenology, of life-stage transitions determines the environmental conditions to which each life stage is exposed and the length of time required to complete a generation. Both environmental and genetic factors contribute to phenological variation, yet predicting their combined effect on life cycles across a geographic range remains a challenge. We linked submodels of the plasticity of individual life stages to create an integrated model that predicts life-cycle phenology in complex environments. We parameterized the model for Arabidopsis thaliana and simulated life cycles in four locations. We compared multiple "genotypes" by varying two parameters associated with natural genetic variation in phenology: seed dormancy and floral repression. The model predicted variation in life cycles across locations that qualitatively matches observed natural phenology. Seed dormancy had larger effects on life-cycle length than floral repression, and results suggest that a genetic cline in dormancy maintains a life-cycle length of 1 year across the geographic range of this species. By integrating across life stages, this approach demonstrates how genetic variation in one transition can influence subsequent transitions and the geographic distribution of life cycles more generally.

The influence of socializing agents in the female sport-participation process.

PubMed

Higginson, D C

1985-01-01

This study investigated the influence of socializing agents on the female athletes who participated in the Empire State Games in Syracuse, New York (N = 587). When comparisons were made across life-cycle states (under-13, junior high, and senior high), it was discovered that statistically significant differences existed (p less than 0.0001). It was apparent that the socializing agent influences changed from being mostly parental at the under-13 life-cycle stage to mostly coach/teacher oriented during junior and senior high school years. No significant differences occurred across the three life-cycle stages when the following items were examined: (a) the number of sports in which the female athletes participated, (b) the number of sports learned by the female athletes, and (c) the amount of sport interest developed. It was concluded that socializing agent influences do exist, but change during different periods in the life cycle.

HIV-1 Gag as an Antiviral Target: Development of Assembly and Maturation Inhibitors.

PubMed

Spearman, Paul

2016-01-01

HIV-1 Gag is the master orchestrator of particle assembly. The central role of Gag at multiple stages of the HIV lifecycle has led to efforts to develop drugs that directly target Gag and prevent the formation and release of infectious particles. Until recently, however, only the catalytic site protease inhibitors have been available to inhibit late stages of HIV replication. This review summarizes the current state of development of antivirals that target Gag or disrupt late events in the retrovirus lifecycle such as maturation of the viral capsid. Maturation inhibitors represent an exciting new series of antiviral compounds, including those that specifically target CA-SP1 cleavage and the allosteric integrase inhibitors that inhibit maturation by a completely different mechanism. Numerous small molecules and peptides targeting CA have been studied in attempts to disrupt steps in assembly. Efforts to target CA have recently gained considerable momentum from the development of small molecules that bind CA and alter capsid stability at the post-entry stage of the lifecycle. Efforts to develop antivirals that inhibit incorporation of genomic RNA or to inhibit late budding events remain in preliminary stages of development. Overall, the development of novel antivirals targeting Gag and the late stages in HIV replication appears much closer to success than ever, with the new maturation inhibitors leading the way.

Clinical Research Informatics: Supporting the Research Study Lifecycle.

PubMed

Johnson, S B

2017-08-01

Objectives: The primary goal of this review is to summarize significant developments in the field of Clinical Research Informatics (CRI) over the years 2015-2016. The secondary goal is to contribute to a deeper understanding of CRI as a field, through the development of a strategy for searching and classifying CRI publications. Methods: A search strategy was developed to query the PubMed database, using medical subject headings to both select and exclude articles, and filtering publications by date and other characteristics. A manual review classified publications using stages in the "research study lifecycle", with key stages that include study definition, participant enrollment, data management, data analysis, and results dissemination. Results: The search strategy generated 510 publications. The manual classification identified 125 publications as relevant to CRI, which were classified into seven different stages of the research lifecycle, and one additional class that pertained to multiple stages, referring to general infrastructure or standards. Important cross-cutting themes included new applications of electronic media (Internet, social media, mobile devices), standardization of data and procedures, and increased automation through the use of data mining and big data methods. Conclusions: The review revealed increased interest and support for CRI in large-scale projects across institutions, regionally, nationally, and internationally. A search strategy based on medical subject headings can find many relevant papers, but a large number of non-relevant papers need to be detected using text words which pertain to closely related fields such as computational statistics and clinical informatics. The research lifecycle was useful as a classification scheme by highlighting the relevance to the users of clinical research informatics solutions. Georg Thieme Verlag KG Stuttgart.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pirhonen, P.

Life-cycle assessment is usually based on regular discharges that occur at a more or less constant rate. Nevertheless, the more factors that are taken into account in the LCA the better picture it gives on the environmental aspects of a product. In this study an approach to incorporate accidental releases into a products` life-cycle assessment was developed. In this approach accidental releases are divided into two categories. The first category consists of those unplanned releases which occur with a predicted level and frequency. Due to the high frequency and small release size at a time, these accidental releases can bemore » compared to continuous emissions. Their global impacts are studied in this approach. Accidental releases of the second category are sudden, unplanned releases caused by exceptional situations, e.g. technical failure, action error or disturbances in process conditions. These releases have a singular character and local impacts are typical of them. As far as the accidental releases of the second category are concerned, the approach introduced in this study results in a risk value for every stage of a life-cycle, the sum of which is a risk value for the whole life-cycle. Risk value is based on occurrence frequencies of incidents and potential environmental damage caused by releases. Risk value illustrates the level of potential damage caused by accidental releases related to the system under study and is meant to be used for comparison of these levels of two different products. It can also be used to compare the risk levels of different stages of the life-cycle. An approach was illustrated using petrol as an example product. The whole life-cycle of petrol from crude oil production to the consumption of petrol was studied.« less

Comparison of various staining methods for the detection of Cryptosporidium in cell-free culture.

PubMed

Boxell, Annika; Hijjawi, Nawal; Monis, Paul; Ryan, Una

2008-09-01

The complete development of Cryptosporidium in host cell-free medium first described in 2004, represented a significant advance that can facilitate many aspects of Cryptosporidium research. A current limitation of host cell-free cultivation is the difficulty involved in visualising the life-cycle stages as they are very small in size, morphologically difficult to identify and dispersed throughout the media. This is in contrast to conventional cell culture methods for Cryptosporidium, where it is possible to focus on the host cells and view the foci of infection on the host cells. In the present study, we compared three specific and three non-specific techniques for visualising Cryptosporidium parvum life-cycle stages in cell-free culture; antibody staining using anti-sporozoite and anti-oocyst wall antibodies (Sporo-Glo and Crypto Cel), fluorescent in-situ hybridization (FISH) using a Cryptosporidium specific rRNA oligonucleotide probe and the non-specific dyes; Texas Red, carboxyfluorescein diacetate succinimidyl ester (CFSE) and 4,6' diamino-2-phenylindole dihydrochloride (DAPI). Results revealed that a combination of Sporo-Glo and Crypto Cel staining resulted in easy and reliable identification of all life-cycle stages.

Design for life-cycle profit with simultaneous consideration of initial manufacturing and end-of-life remanufacturing

NASA Astrophysics Data System (ADS)

Kwak, Minjung; Kim, Harrison

2015-01-01

Remanufacturing is emerging as a promising solution for achieving green, profitable businesses. This article considers a manufacturer that produces new products and also remanufactured versions of the new products that become available at the end of their life cycle. For such a manufacturer, design decisions at the initial design stage determine both the current profit from manufacturing and future profit from remanufacturing. To maximize the total profit, design decisions must carefully consider both ends of product life cycle, i.e. manufacturing and end-of-life stages. This article proposes a decision-support model for the life-cycle design using mixed-integer nonlinear programming. With an aim to maximize the total life-cycle profit, the proposed model searches for an (at least locally) optimal product design (i.e. design specifications and the selling price) for the new and remanufactured products. It optimizes both the initial design and design upgrades at the end-of-life stage and also provides corresponding production strategies, including production quantities and take-back rate. The model is extended to a multi-objective model that maximizes both economic profit and environmental-impact saving. To illustrate, the developed model is demonstrated with an example of a desktop computer.

A review of endoparasitic acarines of Malaysia with special reference to novel endoparasitism of mites in amphibious sea snakes and supplementary notes on ecology of chiggers.

PubMed

Nadchatram, M

2006-06-01

Some 2,000 species of mites of the family Trombiculidae are known in the world. The 6-legged larvae are mostly ectoparasites of reptiles, birds, mammals and invertebrates. Their 8-legged active nymphs and adults are free-living predators. In the Asia-Pacific region, a few species in various genera are vectors of scrub typhus and scrub-itch. In this a paper, a very bizarre trombiculid species, Vatacarus ipoides Southcott 1957, endoparasitic in the trachea of the amphibious sea snake, Laticauda colubrina (Schenider) is re-described based mostly on new-born larvae reared in the laboratory. Life history study of the mite produced very novel and interesting results. A brief account of the life-cycle was presented at the first laboratory demonstration of the Malaysian Society of Parasitology and Tropical Medicine Meeting by Nadchatram and Audy (1965). The life history is illustrated and described here in greater detail. The active nymphal, and the akinetic teleiophane stages are bypassed, which is unusual in the life-cycle of the family Trombiculidae. Also, the larva is the only stage in the life-cycle that feeds. The sexes are predetermined in the larval neosomatic stage and give rise to small males and bigger females. Having obtained adults of the species, by rearing, it is deemed unnecessary for the original proposal by Southcott to erect a new family, Vatacaridae, because the adults share all the attributes of the family Trombiculidae. The male and female obtained through laboratory rearing are illustrated for the first time. Relationship of V. ipoides with Laticauda snakes show close host-specificity, in a group of acarines that are generally habitat-specific. Possible explanations for their association are discussed. The unusual morphology and the formation of new structures during an instar is of ontogenetic and evolutionary importance. The hypertrophic larvae are superficially vermiform, rather than typically acarine in shape. This, and other biological features, necessitated the proposal of new morphological terms, and they are discussed here.

Comparing the environmental footprints of home-care and personal-hygiene products: the relevance of different life-cycle phases.

PubMed

Koehler, Annette; Wildbolz, Caroline

2009-11-15

An in-depth life-cycle assessment of nine home-care and personal-hygiene products was conducted to determine the ecological relevance of different life-cycle phases and compare the environmental profiles of products serving equal applications. Using detailed data from industry and consumer-behavior studies a broad range of environmental impacts were analyzed to identify the main drivers in each life-cycle stage and potentials for improving the environmental footprints. Although chemical production significantly adds to environmental burdens, substantial impacts are caused in the consumer-use phase. As such, this research provides recommendations for product development, supply chain management, product policies, and consumer use. To reduce environmental burdens products should, for instance, be produced in concentrated form, while consumers should apply correct product dosages and low water temperatures during product application.

A Global Survey of ATPase Activity in Plasmodium falciparum Asexual Blood Stages and Gametocytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortega, Corrie; Frando, Andrew; Webb-Robertson, Bobbie-Jo

Effective malaria control and elimination in hyperendemic areas of the world will require treatment of disease-causing Plasmodium falciparum (Pf) blood stage infection but also blocking parasite transmission from humans to mosquito to prevent disease spread. Numerous antimalarial drugs have become ineffective due to parasite drug resistance and many currently used therapies do not kill gametocytes, highly specialized sexual parasite stages with distinct physiology that are necessary for transmission from the human host to the mosquito vector. Further confounding next generation drug development against Pf is the lack of known biochemical activity for most parasite gene products as well as themore » unknown metabolic needs of non-replicating gametocyte. Here, we take a systematic activity-based proteomics approach to survey the large and druggable ATPase family that is associated with replicating blood stage asexual parasites and transmissible gametocytes. We experimentally confirm existing annotation and predict ATPase function for 38 uncharacterized proteins. ATPase activity broadly changes during the transition from asexual schizonts to gametocytes, indicating altered metabolism and regulatory roles of ATPases specific for each lifecycle stage. By mapping the activity of ATPases associated with gametocytogenesis, we assign biochemical activity to a large number of uncharacterized proteins and identify new candidate transmission blocking targets.« less

An Alternative to Farmer Age as an Indicator of Life-Cycle Stage: The Case for a Farm Family Age Index

ERIC Educational Resources Information Center

Burton, Rob J. F.

2006-01-01

In studies of farming, the age of the principal decision-maker (PDM) has been associated with numerous farm structural and managerial features and has been widely accepted as a good indicator of the influence of life-cycle factors on decision-making. As such, it has become an important aspect of many quantitative studies of agricultural change.…

Cradle-to-gate life-cycle inventory of U.S. wood products production: CORRIM phase I and phase II products

Treesearch

Maureen E. Puettmann; Richard Bergman; Steve Hubbard; Leonard Johnson; Bruce Lippke; Elaine Oneil; Francis G. Wagner

2010-01-01

This article documents cradle-to-gate life-cycle inventories for softwood lumber, hardwood lumber, and solid-strip hardwood flooring manufacturing from the Inland Northwest and the Northeast–North Central regions of the US. Environmental impacts were measured based on emissions to air and water, solid waste, energy consumption, and resource use. The manufacturing stage...

Optimization of 2-Anilino 4-Amino Substituted Quinazolines into Potent Antimalarial Agents with Oral in Vivo Activity.

PubMed

Gilson, Paul R; Tan, Cyrus; Jarman, Kate E; Lowes, Kym N; Curtis, Joan M; Nguyen, William; Di Rago, Adrian E; Bullen, Hayley E; Prinz, Boris; Duffy, Sandra; Baell, Jonathan B; Hutton, Craig A; Jousset Subroux, Helene; Crabb, Brendan S; Avery, Vicky M; Cowman, Alan F; Sleebs, Brad E

2017-02-09

Novel antimalarial therapeutics that target multiple stages of the parasite lifecycle are urgently required to tackle the emerging problem of resistance with current drugs. Here, we describe the optimization of the 2-anilino quinazoline class as antimalarial agents. The class, identified from publicly available antimalarial screening data, was optimized to generate lead compounds that possess potent antimalarial activity against P. falciparum parasites comparable to the known antimalarials, chloroquine and mefloquine. During the optimization process, we defined the functionality necessary for activity and improved in vitro metabolism and solubility. The resultant lead compounds possess potent activity against a multidrug resistant strain of P. falciparum and arrest parasites at the ring phase of the asexual stage and also gametocytogensis. Finally, we show that the lead compounds are orally efficacious in a 4 day murine model of malaria disease burden.

Evolution of RFID Applications in Construction: A Literature Review

PubMed Central

Valero, Enrique; Adán, Antonio; Cerrada, Carlos

2015-01-01

Radio frequency identification (RFID) technology has been widely used in the field of construction during the last two decades. Basically, RFID facilitates the control on a wide variety of processes in different stages of the lifecycle of a building, from its conception to its inhabitance. The main objective of this paper is to present a review of RFID applications in the construction industry, pointing out the existing developments, limitations and gaps. The paper presents the establishment of the RFID technology in four main stages of the lifecycle of a facility: planning and design, construction and commission and operation and maintenance. Concerning this last stage, an RFID application aiming to facilitate the identification of pieces of furniture in scanned inhabited environments is presented. Conclusions and future advances are presented at the end of the paper. PMID:26151210

Product-related research: how research can contribute to successful life-cycle management.

PubMed

Sandner, Peter; Ziegelbauer, Karl

2008-05-01

Declining productivity with decreasing new molecular entity output combined with increased R&D spending is one of the key challenges for the entire pharmaceutical industry. In order to offset decreasing new molecular entity output, life-cycle management activities for established drugs become more and more important to maintain or even expand clinical indication and market opportunities. Life-cycle management covers a whole range of activities from strategic pricing to a next generation product launch. In this communication, we review how research organizations can contribute to successful life-cycle management strategies using phosphodiesterase 5 inhibitors as an example.

Full Life-Cycle Defect Management Assessment: Initial Inspection Data Collection Results and Research Questions for Further Study

NASA Technical Reports Server (NTRS)

Shull, Forrest; Feldmann, Raimund; Haingaertner, Ralf; Regardie, Myrna; Seaman, Carolyn

2007-01-01

It is often the case in software projects that when schedule and budget resources are limited, the Verification and Validation (V&V) activities suffer. Fewer V&V activities can be afforded and moreover, short-term challenges can result in V&V activities being scaled back or dropped altogether. As a result, too often the default solution is to save activities for improving software quality until too late in the life-cycle, relying on late-term code inspections followed by thorough testing activities to reduce defect counts to acceptable levels. As many project managers realize, however, this is a resource-intensive way of achieving the required quality for software. The Full Life-cycle Defect Management Assessment Initiative, funded by NASA s Office of Safety and Mission Assurance under the Software Assurance Research Program, aims to address these problems by: Improving the effectiveness of early life-cycle V&V activities to make their benefits more attractive to team leads. Specifically, we focus on software inspection, a proven method that can be applied to any software work product, long before executable code has been developed; Better communicating this effectiveness to software development teams, along with suggestions for parameters to improve in the future to increase effectiveness; Analyzing the impact of early life-cycle V&V on the effectiveness and cost required for late life-cycle V&V activities, such as testing, in order to make the tradeoffs more apparent. This white paper reports on an initial milestone in this work, the development of a preliminary model of inspection effectiveness across multiple NASA Centers. This model contributes toward reaching our project goals by: Allowing an examination of inspection parameters, across different types of projects and different work products, for an analysis of factors that impact defect detection effectiveness. Allowing a comparison of this NASA-specific model to existing recommendations in the literature regarding how to plan effective inspections. Forming a baseline model which can be extended to incorporate factors describing: the numbers and types of defects that are missed by inspections; how such defects flow downstream through software development phases; how effectively they can be caught by testing activities in the late stages of development. The model has been implemented in a prototype web-enabled decision-support tool which allows developers to enter their inspection data and receive feedback based on a comparison against the model. The tool also allows users to access reusable materials (such as checklists) from projects included in the baseline. Both the tool itself and the model underlying it will continue to be extended throughout the remainder of this initiative. As results of analyzing inspection effectiveness for defect containment are determined, they can be shared via the tool and also via updates to existing training courses on metrics and software inspections. Moreover, the tool will help satisfy key CMMI requirements for the NASA Centers, as it will enable NASA to take a global view across peer review results for various types of projects to identify systemic problems. This analysis can result in continuous improvements to the approach to verification.

Assessment Methodology for Process Validation Lifecycle Stage 3A.

PubMed

Sayeed-Desta, Naheed; Pazhayattil, Ajay Babu; Collins, Jordan; Chen, Shu; Ingram, Marzena; Spes, Jana

2017-07-01

The paper introduces evaluation methodologies and associated statistical approaches for process validation lifecycle Stage 3A. The assessment tools proposed can be applied to newly developed and launched small molecule as well as bio-pharma products, where substantial process and product knowledge has been gathered. The following elements may be included in Stage 3A: number of 3A batch determination; evaluation of critical material attributes, critical process parameters, critical quality attributes; in vivo in vitro correlation; estimation of inherent process variability (IPV) and PaCS index; process capability and quality dashboard (PCQd); and enhanced control strategy. US FDA guidance on Process Validation: General Principles and Practices, January 2011 encourages applying previous credible experience with suitably similar products and processes. A complete Stage 3A evaluation is a valuable resource for product development and future risk mitigation of similar products and processes. Elements of 3A assessment were developed to address industry and regulatory guidance requirements. The conclusions made provide sufficient information to make a scientific and risk-based decision on product robustness.

Life-cycle assessment of typical Portuguese cork oak woodlands.

PubMed

González-García, Sara; Dias, Ana Cláudia; Arroja, Luis

2013-05-01

Cork forest systems are responsible for making an important economic contribution to the Mediterranean region, especially Portugal where the cork oak woodlands or montados contain about 32% of the world's area. The environmental profile derived from reproduction cork production and extraction in two Portuguese regions (Tagus valley and Alentejo) representative of the Portuguese sector were assessed in detail using the Life-Cycle Assessment (LCA) methodology from a cradle-to-gate perspective. The production line was divided into four stages considering all the processes involved: stand establishment, stand management, cork stripping and field recovery. According to the environmental results, there were remarkable differences between the two production scenarios mainly due to the intensity and repetition of forest activities even though the cork yield was reported to be the same. The management system in the Alentejo region presented the worse environmental profile in almost all the impact categories under assessment, mainly due to the shorter cycle duration of the mechanical cleaning and pruning processes. Cork stripping was identified in both scenarios as the production stage with the highest contribution to the environmental profile due to the cleaning and pruning processes. A sensitivity assessment concerning the cork yield was performed since the average production yields in the Portuguese montados are lower than the ones used in this study. Thus, if the cork yield is reduced, the environmental profile in both scenarios gets worse since almost all the forest activities involved are the same. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluating Games-Based Learning

ERIC Educational Resources Information Center

Hainey, Thomas; Connolly, Thomas

2010-01-01

A highly important part of software engineering education is requirements collection and analysis, one of the initial stages of the Software Development Lifecycle. No other conceptual work is as difficult to rectify at a later stage or as damaging to the overall system if performed incorrectly. As software engineering is a field with a reputation…

Life-cycle energy and GHG emissions of forest biomass harvest and transport for biofuel production in Michigan

DOE PAGES

Zhang, Fengli; Johnson, Dana M.; Wang, Jinjiang

2015-04-01

High dependence on imported oil has increased U.S. strategic vulnerability and prompted more research in the area of renewable energy production. Ethanol production from renewable woody biomass, which could be a substitute for gasoline, has seen increased interest. This study analysed energy use and greenhouse gas emission impacts on the forest biomass supply chain activities within the State of Michigan. A life-cycle assessment of harvesting and transportation stages was completed utilizing peer-reviewed literature. Results for forest-delivered ethanol were compared with those for petroleum gasoline using data specific to the U.S. The analysis from a woody biomass feedstock supply perspective uncoveredmore » that ethanol production is more environmentally friendly (about 62% less greenhouse gas emissions) compared with petroleum based fossil fuel production. Sensitivity analysis was conducted with key inputs associated with harvesting and transportation operations. The results showed that research focused on improving biomass recovery efficiency and truck fuel economy further reduced GHG emissions and energy consumption.« less

Life-cycle energy and GHG emissions of forest biomass harvest and transport for biofuel production in Michigan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Fengli; Johnson, Dana M.; Wang, Jinjiang

High dependence on imported oil has increased U.S. strategic vulnerability and prompted more research in the area of renewable energy production. Ethanol production from renewable woody biomass, which could be a substitute for gasoline, has seen increased interest. This study analysed energy use and greenhouse gas emission impacts on the forest biomass supply chain activities within the State of Michigan. A life-cycle assessment of harvesting and transportation stages was completed utilizing peer-reviewed literature. Results for forest-delivered ethanol were compared with those for petroleum gasoline using data specific to the U.S. The analysis from a woody biomass feedstock supply perspective uncoveredmore » that ethanol production is more environmentally friendly (about 62% less greenhouse gas emissions) compared with petroleum based fossil fuel production. Sensitivity analysis was conducted with key inputs associated with harvesting and transportation operations. The results showed that research focused on improving biomass recovery efficiency and truck fuel economy further reduced GHG emissions and energy consumption.« less

Three-year lifecycle, large body, and very high threshold temperature in the cricket Gryllus argenteus for special adaptation to desiccation cycle in Malawi.

PubMed

Kosumi, Takuya; Takeda, Makio

2017-08-08

In temperate climates, the initiation and termination of diapause synchronize the stress-tolerant stage with the stressful season and reproduction with the non-stressful season in many insects. Synchronization is often regulated by photoperiodism.Voltinism and the ultimate size of adults are also important determinants for their lifecycle, and different diapause stages and voltinism patterns are known in crickets.Here, we investigated the life history of the African cricket Gryllus argenteus from Malawi, which is a typical arid tropical highland. The climate is characterized by alternating arid and wet seasons, each of which lasts for half a year, and where the available heat mass is much less than lowlands at the same latitude. We first measured the nymphal duration at each rearing temperature and calculated the lower developmental threshold (t 0 ) to be 20.19 °C based on Ikemoto and Takai (2000) and 19.38 °C based on a conventional line-fitting method. These values are very high relative to many other insects. The local temperature in winter does not fall below 15 °C, but this is much higher than the lethal limit. This suggested that critical stress in this locality was not coldness but low precipitation in winter. We estimated, based both on local temperature change and the Ikemoto and Takai's t 0 , that G. argenteus required 3 years to complete its lifecycle unlike wet lowland species, where univoltinism or multi-voltinism are commonplace. Photoperiodism was observed in this species, but due to a lag between annual cycles in photoperiod, temperature, and humidity, photoperiodism alone cannot atune their lifecycle with local conditions.Synchronization in this species was achieved by three different adaptations: photoperiodism, high t 0 , and large body size, which give it a long lifecycle. Although the species cannot achieve a univoltine lifecycle because of its high t 0 value, it can escape from dry season by entering diapause at moderate temperatures, probably thereby achieving adaptive synchrony of lifecycle with both favorable and unfavorable seasons. A comparison between a conventional photothermogram and a newly formulated photohydrogram or photohygrogram demonstrates that even though sufficient heat is available, scarcity of water and thus scarcity of foliage should force the cricket to maintain diapause at intermediate temperature. The results suggested that high t 0 , large body size, and multi-ennial lifecycle mutually affect each other and formulate a unique adaptation under such an extreme environment.

Three-year lifecycle, large body, and very high threshold temperature in the cricket Gryllus argenteus for special adaptation to desiccation cycle in Malawi

NASA Astrophysics Data System (ADS)

Kosumi, Takuya; Takeda, Makio

2017-10-01

In temperate climates, the initiation and termination of diapause synchronize the stress-tolerant stage with the stressful season and reproduction with the non-stressful season in many insects. Synchronization is often regulated by photoperiodism. Voltinism and the ultimate size of adults are also important determinants for their lifecycle, and different diapause stages and voltinism patterns are known in crickets. Here, we investigated the life history of the African cricket Gryllus argenteus from Malawi, which is a typical arid tropical highland. The climate is characterized by alternating arid and wet seasons, each of which lasts for half a year, and where the available heat mass is much less than lowlands at the same latitude. We first measured the nymphal duration at each rearing temperature and calculated the lower developmental threshold ( t 0) to be 20.19 °C based on Ikemoto and Takai (2000) and 19.38 °C based on a conventional line-fitting method. These values are very high relative to many other insects. The local temperature in winter does not fall below 15 °C, but this is much higher than the lethal limit. This suggested that critical stress in this locality was not coldness but low precipitation in winter. We estimated, based both on local temperature change and the Ikemoto and Takai's t 0, that G. argenteus required 3 years to complete its lifecycle unlike wet lowland species, where univoltinism or multi-voltinism are commonplace. Photoperiodism was observed in this species, but due to a lag between annual cycles in photoperiod, temperature, and humidity, photoperiodism alone cannot atune their lifecycle with local conditions. Synchronization in this species was achieved by three different adaptations: photoperiodism, high t 0, and large body size, which give it a long lifecycle. Although the species cannot achieve a univoltine lifecycle because of its high t0 value, it can escape from dry season by entering diapause at moderate temperatures, probably thereby achieving adaptive synchrony of lifecycle with both favorable and unfavorable seasons. A comparison between a conventional photothermogram and a newly formulated photohydrogram or photohygrogram demonstrates that even though sufficient heat is available, scarcity of water and thus scarcity of foliage should force the cricket to maintain diapause at intermediate temperature. The results suggested that high t 0, large body size, and multi-ennial lifecycle mutually affect each other and formulate a unique adaptation under such an extreme environment.

Telescience Resource Kit Software Lifecycle

NASA Technical Reports Server (NTRS)

Griner, Carolyn S.; Schneider, Michelle

1998-01-01

The challenge of a global operations capability led to the Telescience Resource Kit (TReK) project, an in-house software development project of the Mission Operations Laboratory (MOL) at NASA's Marshall Space Flight Center (MSFC). The TReK system is being developed as an inexpensive comprehensive personal computer- (PC-) based ground support system that can be used by payload users from their home sites to interact with their payloads on board the International Space Station (ISS). The TReK project is currently using a combination of the spiral lifecycle model and the incremental lifecycle model. As with any software development project, there are four activities that can be very time consuming: Software design and development, project documentation, testing, and umbrella activities, such as quality assurance and configuration management. In order to produce a quality product, it is critical that each of these activities receive the appropriate amount of attention. For TReK, the challenge was to lay out a lifecycle and project plan that provides full support for these activities, is flexible, provides a way to deal with changing risks, can accommodate unknowns, and can respond to changes in the environment quickly. This paper will provide an overview of the TReK lifecycle, a description of the project's environment, and a general overview of project activities.

How Work Positions Affect the Research Activity and Information Behaviour of Laboratory Scientists in the Research Lifecycle: Applying Activity Theory

ERIC Educational Resources Information Center

Kwon, Nahyun

2017-01-01

Introduction: This study was conducted to investigate the characteristics of research and information activities of laboratory scientists in different work positions throughout a research lifecycle. Activity theory was applied as the conceptual and analytical framework. Method: Taking a qualitative research approach, in-depth interviews and field…

Evaluation of Endocrine Effects in Birds: A Case for a Targeted, Life-stage and Endpoint Specific Approach

EPA Science Inventory

The EFSA "Scientific Opinion on the Science Behind the Guidance" document on risk assessment for birds and mammals has a chapter on risk assessment of substances with endocrine-disrupting properties in birds. It discusses that targeted partial life-cycle or critical life-stage te...

Functional RNA structures throughout the Hepatitis C Virus genome.

PubMed

Adams, Rebecca L; Pirakitikulr, Nathan; Pyle, Anna Marie

2017-06-01

The single-stranded Hepatitis C Virus (HCV) genome adopts a set of elaborate RNA structures that are involved in every stage of the viral lifecycle. Recent advances in chemical probing, sequencing, and structural biology have facilitated analysis of RNA folding on a genome-wide scale, revealing novel structures and networks of interactions. These studies have underscored the active role played by RNA in every function of HCV and they open the door to new types of RNA-targeted therapeutics. Copyright © 2017 Elsevier B.V. All rights reserved.

Proteomic Analysis of the Schistosoma mansoni Miracidium.

PubMed

Wang, Tianfang; Zhao, Min; Rotgans, Bronwyn A; Strong, April; Liang, Di; Ni, Guoying; Limpanont, Yanin; Ramasoota, Pongrama; McManus, Donald P; Cummins, Scott F

2016-01-01

Despite extensive control efforts, schistosomiasis continues to be a major public health problem in developing nations in the tropics and sub-tropics. The miracidium, along with the cercaria, both of which are water-borne and free-living, are the only two stages in the life-cycle of Schistosoma mansoni which are involved in host invasion. Miracidia penetrate intermediate host snails and develop into sporocysts, which lead to cercariae that can infect humans. Infection of the snail host by the miracidium represents an ideal point at which to interrupt the parasite's life-cycle. This research focuses on an analysis of the miracidium proteome, including those proteins that are secreted. We have identified a repertoire of proteins in the S. mansoni miracidium at 2 hours post-hatch, including proteases, venom allergen-like proteins, receptors and HSP70, which might play roles in snail-parasite interplay. Proteins involved in energy production and conservation were prevalent, as were proteins predicted to be associated with defence. This study also provides a strong foundation for further understanding the roles that neurohormones play in host-seeking by schistosomes, with the potential for development of novel anthelmintics that interfere with its various life-cycle stages.

Methods Used to Support a Life Cycle of Complex Engineering Products

NASA Astrophysics Data System (ADS)

Zakharova, Alexandra A.; Kolegova, Olga A.; Nekrasova, Maria E.; Eremenko, Andrey O.

2016-08-01

Management of companies involved in the design, development and operation of complex engineering products recognize the relevance of creating systems for product lifecycle management. A system of methods is proposed to support life cycles of complex engineering products, based on fuzzy set theory and hierarchical analysis. The system of methods serves to demonstrate the grounds for making strategic decisions in an environment of uncertainty, allows the use of expert knowledge, and provides interconnection of decisions at all phases of strategic management and all stages of a complex engineering product lifecycle.

Comparative life-cycle air emissions of coal, domestic natural gas, LNG, and SNG for electricity generation.

PubMed

Jaramillo, Paulina; Griffin, W Michael; Matthews, H Scott

2007-09-01

The U.S. Department of Energy (DOE) estimates that in the coming decades the United States' natural gas (NG) demand for electricity generation will increase. Estimates also suggest that NG supply will increasingly come from imported liquefied natural gas (LNG). Additional supplies of NG could come domestically from the production of synthetic natural gas (SNG) via coal gasification-methanation. The objective of this study is to compare greenhouse gas (GHG), SOx, and NOx life-cycle emissions of electricity generated with NG/LNG/SNG and coal. This life-cycle comparison of air emissions from different fuels can help us better understand the advantages and disadvantages of using coal versus globally sourced NG for electricity generation. Our estimates suggest that with the current fleet of power plants, a mix of domestic NG, LNG, and SNG would have lower GHG emissions than coal. If advanced technologies with carbon capture and sequestration (CCS) are used, however, coal and a mix of domestic NG, LNG, and SNG would have very similar life-cycle GHG emissions. For SOx and NOx we find there are significant emissions in the upstream stages of the NG/ LNG life-cycles, which contribute to a larger range in SOx and NOx emissions for NG/LNG than for coal and SNG.

Visual Analytics Tools for Sustainable Lifecycle Design: Current Status, Challenges, and Future Opportunities.

PubMed

Ramanujan, Devarajan; Bernstein, William Z; Chandrasegaran, Senthil K; Ramani, Karthik

2017-01-01

The rapid rise in technologies for data collection has created an unmatched opportunity to advance the use of data-rich tools for lifecycle decision-making. However, the usefulness of these technologies is limited by the ability to translate lifecycle data into actionable insights for human decision-makers. This is especially true in the case of sustainable lifecycle design (SLD), as the assessment of environmental impacts, and the feasibility of making corresponding design changes, often relies on human expertise and intuition. Supporting human sense-making in SLD requires the use of both data-driven and user-driven methods while exploring lifecycle data. A promising approach for combining the two is through the use of visual analytics (VA) tools. Such tools can leverage the ability of computer-based tools to gather, process, and summarize data along with the ability of human-experts to guide analyses through domain knowledge or data-driven insight. In this paper, we review previous research that has created VA tools in SLD. We also highlight existing challenges and future opportunities for such tools in different lifecycle stages-design, manufacturing, distribution & supply chain, use-phase, end-of-life, as well as life cycle assessment. Our review shows that while the number of VA tools in SLD is relatively small, researchers are increasingly focusing on the subject matter. Our review also suggests that VA tools can address existing challenges in SLD and that significant future opportunities exist.

JPL Innovation Foundry

NASA Technical Reports Server (NTRS)

Sherwood, Brent; McCleese, Daniel J.

2012-01-01

NASA supports the community of mission principal investigators by helping them ideate, mature, and propose concepts for new missions. As NASA's Federally Funded Research and Development Center (FFRDC), JPL is a primary resource for providing this service. The environmental context for the formulation lifecycle evolves continuously. Contemporary trends include: more competitors; more-complex mission ideas; scarcer formulation resources; and higher standards for technical evaluation. Derived requirements for formulation support include: stable, clear, reliable methods tailored for each stage of the formulation lifecycle; on-demand access to standout technical and programmatic subject-matter experts; optimized, outfitted facilities; smart access to learning embodied in a vast oeuvre of prior formulation work; hands-on method coaching. JPL has retooled its provision of integrated formulation lifecycle support to PIs, teams, and program offices in response to this need. This mission formulation enterprise is the JPL Innovation Foundry.

A novel multiple-stage antimalarial agent that inhibits protein synthesis.

PubMed

Baragaña, Beatriz; Hallyburton, Irene; Lee, Marcus C S; Norcross, Neil R; Grimaldi, Raffaella; Otto, Thomas D; Proto, William R; Blagborough, Andrew M; Meister, Stephan; Wirjanata, Grennady; Ruecker, Andrea; Upton, Leanna M; Abraham, Tara S; Almeida, Mariana J; Pradhan, Anupam; Porzelle, Achim; Luksch, Torsten; Martínez, María Santos; Luksch, Torsten; Bolscher, Judith M; Woodland, Andrew; Norval, Suzanne; Zuccotto, Fabio; Thomas, John; Simeons, Frederick; Stojanovski, Laste; Osuna-Cabello, Maria; Brock, Paddy M; Churcher, Tom S; Sala, Katarzyna A; Zakutansky, Sara E; Jiménez-Díaz, María Belén; Sanz, Laura Maria; Riley, Jennifer; Basak, Rajshekhar; Campbell, Michael; Avery, Vicky M; Sauerwein, Robert W; Dechering, Koen J; Noviyanti, Rintis; Campo, Brice; Frearson, Julie A; Angulo-Barturen, Iñigo; Ferrer-Bazaga, Santiago; Gamo, Francisco Javier; Wyatt, Paul G; Leroy, Didier; Siegl, Peter; Delves, Michael J; Kyle, Dennis E; Wittlin, Sergio; Marfurt, Jutta; Price, Ric N; Sinden, Robert E; Winzeler, Elizabeth A; Charman, Susan A; Bebrevska, Lidiya; Gray, David W; Campbell, Simon; Fairlamb, Alan H; Willis, Paul A; Rayner, Julian C; Fidock, David A; Read, Kevin D; Gilbert, Ian H

2015-06-18

There is an urgent need for new drugs to treat malaria, with broad therapeutic potential and novel modes of action, to widen the scope of treatment and to overcome emerging drug resistance. Here we describe the discovery of DDD107498, a compound with a potent and novel spectrum of antimalarial activity against multiple life-cycle stages of the Plasmodium parasite, with good pharmacokinetic properties and an acceptable safety profile. DDD107498 demonstrates potential to address a variety of clinical needs, including single-dose treatment, transmission blocking and chemoprotection. DDD107498 was developed from a screening programme against blood-stage malaria parasites; its molecular target has been identified as translation elongation factor 2 (eEF2), which is responsible for the GTP-dependent translocation of the ribosome along messenger RNA, and is essential for protein synthesis. This discovery of eEF2 as a viable antimalarial drug target opens up new possibilities for drug discovery.

A novel multiple-stage antimalarial agent that inhibits protein synthesis

NASA Astrophysics Data System (ADS)

Baragaña, Beatriz; Hallyburton, Irene; Lee, Marcus C. S.; Norcross, Neil R.; Grimaldi, Raffaella; Otto, Thomas D.; Proto, William R.; Blagborough, Andrew M.; Meister, Stephan; Wirjanata, Grennady; Ruecker, Andrea; Upton, Leanna M.; Abraham, Tara S.; Almeida, Mariana J.; Pradhan, Anupam; Porzelle, Achim; Martínez, María Santos; Bolscher, Judith M.; Woodland, Andrew; Norval, Suzanne; Zuccotto, Fabio; Thomas, John; Simeons, Frederick; Stojanovski, Laste; Osuna-Cabello, Maria; Brock, Paddy M.; Churcher, Tom S.; Sala, Katarzyna A.; Zakutansky, Sara E.; Jiménez-Díaz, María Belén; Sanz, Laura Maria; Riley, Jennifer; Basak, Rajshekhar; Campbell, Michael; Avery, Vicky M.; Sauerwein, Robert W.; Dechering, Koen J.; Noviyanti, Rintis; Campo, Brice; Frearson, Julie A.; Angulo-Barturen, Iñigo; Ferrer-Bazaga, Santiago; Gamo, Francisco Javier; Wyatt, Paul G.; Leroy, Didier; Siegl, Peter; Delves, Michael J.; Kyle, Dennis E.; Wittlin, Sergio; Marfurt, Jutta; Price, Ric N.; Sinden, Robert E.; Winzeler, Elizabeth A.; Charman, Susan A.; Bebrevska, Lidiya; Gray, David W.; Campbell, Simon; Fairlamb, Alan H.; Willis, Paul A.; Rayner, Julian C.; Fidock, David A.; Read, Kevin D.; Gilbert, Ian H.

2015-06-01

There is an urgent need for new drugs to treat malaria, with broad therapeutic potential and novel modes of action, to widen the scope of treatment and to overcome emerging drug resistance. Here we describe the discovery of DDD107498, a compound with a potent and novel spectrum of antimalarial activity against multiple life-cycle stages of the Plasmodium parasite, with good pharmacokinetic properties and an acceptable safety profile. DDD107498 demonstrates potential to address a variety of clinical needs, including single-dose treatment, transmission blocking and chemoprotection. DDD107498 was developed from a screening programme against blood-stage malaria parasites; its molecular target has been identified as translation elongation factor 2 (eEF2), which is responsible for the GTP-dependent translocation of the ribosome along messenger RNA, and is essential for protein synthesis. This discovery of eEF2 as a viable antimalarial drug target opens up new possibilities for drug discovery.

Evaluating Managerial Styles for System Development Life Cycle Stages to Ensure Software Project Success

ERIC Educational Resources Information Center

Kocherla, Showry

2012-01-01

Information technology (IT) projects are considered successful if they are completed on time, within budget, and within scope. Even though, the required tools and methodologies are in place, IT projects continue to fail at a higher rate. Current literature lacks explanation for success within the stages of system development life-cycle (SDLC) such…

The life history of Pleurogenoides malampuzhensis sp. nov. (Digenea: Pleurogenidae) from amphibious and aquatic hosts in Kerala, India.

PubMed

Brinesh, R; Janardanan, K P

2014-06-01

The life-cycle stages of Pleurogenoides malampuzhensis sp. nov. infecting the Indian bullfrog Hoplobatrachus tigerinus (Daudin) and the skipper frog Euphlyctis cyanophlyctis (Schneider) occurring in irrigation canals and paddy fields in Malampuzha, which forms part of the district of Palakkad, Kerala, are described. The species is described, its systematic position discussed and compared with the related species, P. gastroporus (Luhe, 1901) and P. orientalis (Srivastava, 1934). The life-cycle stages, from cercaria to egg-producing adult, were successfully established in the laboratory. Virgulate xiphidiocercariae emerged from the snail Digoniostoma pulchella (Benson). Metacercariae are found in muscle tissues of dragonfly nymphs and become infective to the frogs within 22 days. The pre-patent period is 20 days. Growth and development of both metacercariae and adults are described.

Life-cycle analysis of shale gas and natural gas.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, C.E.; Han, J.; Burnham, A.

2012-01-27

The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. Using the current state of knowledge of the recovery, processing, and distribution of shale gas and conventional natural gas, we have estimated up-to-date, life-cycle greenhouse gas emissions. In addition, we have developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps - such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings - that need to be addressed further. Our base case results showmore » that shale gas life-cycle emissions are 6% lower than those of conventional natural gas. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty regarding whether shale gas emissions are indeed lower than conventional gas emissions. This life-cycle analysis provides insight into the critical stages in the natural gas industry where emissions occur and where opportunities exist to reduce the greenhouse gas footprint of natural gas.« less

A Life-Cycle Assessment of Biofuels: Tracing Energy and Carbon through a Fuel-Production System

ERIC Educational Resources Information Center

Krauskopf, Sara

2010-01-01

A life-cycle assessment (LCA) is a tool used by engineers to make measurements of net energy, greenhouse gas production, water consumption, and other items of concern. This article describes an activity designed to walk students through the qualitative part of an LCA. It asks them to consider the life-cycle costs of ethanol production, in terms of…

Stage-specific Proteomes from Onchocerca ochengi, Sister Species of the Human River Blindness Parasite, Uncover Adaptations to a Nodular Lifestyle.

PubMed

Armstrong, Stuart D; Xia, Dong; Bah, Germanus S; Krishna, Ritesh; Ngangyung, Henrietta F; LaCourse, E James; McSorley, Henry J; Kengne-Ouafo, Jonas A; Chounna-Ndongmo, Patrick W; Wanji, Samuel; Enyong, Peter A; Taylor, David W; Blaxter, Mark L; Wastling, Jonathan M; Tanya, Vincent N; Makepeace, Benjamin L

2016-08-01

Despite 40 years of control efforts, onchocerciasis (river blindness) remains one of the most important neglected tropical diseases, with 17 million people affected. The etiological agent, Onchocerca volvulus, is a filarial nematode with a complex lifecycle involving several distinct stages in the definitive host and blackfly vector. The challenges of obtaining sufficient material have prevented high-throughput studies and the development of novel strategies for disease control and diagnosis. Here, we utilize the closest relative of O. volvulus, the bovine parasite Onchocerca ochengi, to compare stage-specific proteomes and host-parasite interactions within the secretome. We identified a total of 4260 unique O. ochengi proteins from adult males and females, infective larvae, intrauterine microfilariae, and fluid from intradermal nodules. In addition, 135 proteins were detected from the obligate Wolbachia symbiont. Observed protein families that were enriched in all whole body extracts relative to the complete search database included immunoglobulin-domain proteins, whereas redox and detoxification enzymes and proteins involved in intracellular transport displayed stage-specific overrepresentation. Unexpectedly, the larval stages exhibited enrichment for several mitochondrial-related protein families, including members of peptidase family M16 and proteins which mediate mitochondrial fission and fusion. Quantification of proteins across the lifecycle using the Hi-3 approach supported these qualitative analyses. In nodule fluid, we identified 94 O. ochengi secreted proteins, including homologs of transforming growth factor-β and a second member of a novel 6-ShK toxin domain family, which was originally described from a model filarial nematode (Litomosoides sigmodontis). Strikingly, the 498 bovine proteins identified in nodule fluid were strongly dominated by antimicrobial proteins, especially cathelicidins. This first high-throughput analysis of an Onchocerca spp. proteome across the lifecycle highlights its profound complexity and emphasizes the extremely close relationship between O. ochengi and O. volvulus The insights presented here provide new candidates for vaccine development, drug targeting and diagnostic biomarkers. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

Stage-specific Proteomes from Onchocerca ochengi, Sister Species of the Human River Blindness Parasite, Uncover Adaptations to a Nodular Lifestyle*

PubMed Central

Armstrong, Stuart D.; Xia, Dong; Bah, Germanus S.; Krishna, Ritesh; Ngangyung, Henrietta F.; LaCourse, E. James; McSorley, Henry J.; Kengne-Ouafo, Jonas A.; Chounna-Ndongmo, Patrick W.; Wanji, Samuel; Enyong, Peter A.; Taylor, David W.; Blaxter, Mark L.; Wastling, Jonathan M.; Tanya, Vincent N.; Makepeace, Benjamin L.

2016-01-01

Despite 40 years of control efforts, onchocerciasis (river blindness) remains one of the most important neglected tropical diseases, with 17 million people affected. The etiological agent, Onchocerca volvulus, is a filarial nematode with a complex lifecycle involving several distinct stages in the definitive host and blackfly vector. The challenges of obtaining sufficient material have prevented high-throughput studies and the development of novel strategies for disease control and diagnosis. Here, we utilize the closest relative of O. volvulus, the bovine parasite Onchocerca ochengi, to compare stage-specific proteomes and host-parasite interactions within the secretome. We identified a total of 4260 unique O. ochengi proteins from adult males and females, infective larvae, intrauterine microfilariae, and fluid from intradermal nodules. In addition, 135 proteins were detected from the obligate Wolbachia symbiont. Observed protein families that were enriched in all whole body extracts relative to the complete search database included immunoglobulin-domain proteins, whereas redox and detoxification enzymes and proteins involved in intracellular transport displayed stage-specific overrepresentation. Unexpectedly, the larval stages exhibited enrichment for several mitochondrial-related protein families, including members of peptidase family M16 and proteins which mediate mitochondrial fission and fusion. Quantification of proteins across the lifecycle using the Hi-3 approach supported these qualitative analyses. In nodule fluid, we identified 94 O. ochengi secreted proteins, including homologs of transforming growth factor-β and a second member of a novel 6-ShK toxin domain family, which was originally described from a model filarial nematode (Litomosoides sigmodontis). Strikingly, the 498 bovine proteins identified in nodule fluid were strongly dominated by antimicrobial proteins, especially cathelicidins. This first high-throughput analysis of an Onchocerca spp. proteome across the lifecycle highlights its profound complexity and emphasizes the extremely close relationship between O. ochengi and O. volvulus. The insights presented here provide new candidates for vaccine development, drug targeting and diagnostic biomarkers. PMID:27226403

Emiliania huxleyi endures N-limitation with an efficient metabolic budgeting and effective ATP synthesis.

PubMed

Rokitta, Sebastian D; Von Dassow, Peter; Rost, Björn; John, Uwe

2014-12-02

Global change will affect patterns of nutrient upwelling in marine environments, potentially becoming even stricter regulators of phytoplankton primary productivity. To better understand phytoplankton nutrient utilization on the subcellular basis, we assessed the transcriptomic responses of the life-cycle stages of the biogeochemically important microalgae Emiliania huxleyi to nitrogen-limitation. Cells grown in batch cultures were harvested at 'early' and 'full' nitrogen-limitation and were compared with non-limited cells. We applied microarray-based transcriptome profilings, covering ~10.000 known E. huxleyi gene models, and screened for expression patterns that indicate the subcellular responses. The diploid life-cycle stage scavenges nitrogen from external organic sources and -like diatoms- uses the ornithine-urea cycle to rapidly turn over cellular nitrogen. The haploid stage reacts similarly, although nitrogen scavenging is less pronounced and lipid oxidation is more prominent. Generally, polyamines and proline appear to constitute major organic pools that back up cellular nitrogen. Both stages induce a malate:quinone-oxidoreductase that efficiently feeds electrons into the respiratory chain and drives ATP generation with reduced respiratory carbon throughput. The use of the ornithine-urea cycle to budget the cellular nitrogen in situations of limitation resembles the responses observed earlier in diatoms. This suggests that underlying biochemical mechanisms are conserved among distant clades of marine phototrophic protists. The ornithine-urea cycle and proline oxidation appear to constitute a sensory-regulatory system that monitors and controls cellular nitrogen budgets under limitation. The similarity between the responses of the life-cycle stages, despite the usage of different genes, also indicates a strong functional consistency in the responses to nitrogen-limitation that appears to be owed to biochemical requirements. The malate:quinone-oxidoreductase is a genomic feature that appears to be absent from diatom genomes, and it is likely to strongly contribute to the uniquely high endurance of E. huxleyi under nutrient limitation.

Carbon footprint of forest and tree utilization technologies in life cycle approach

NASA Astrophysics Data System (ADS)

Polgár, András; Pécsinger, Judit

2017-04-01

In our research project a suitable method has been developed related the technological aspect of the environmental assessment of land use changes caused by climate change. We have prepared an eco-balance (environmental inventory) to the environmental effects classification in life-cycle approach in connection with the typical agricultural / forest and tree utilization technologies. The use of balances and environmental classification makes possible to compare land-use technologies and their environmental effects per common functional unit. In order to test our environmental analysis model, we carried out surveys in sample of forest stands. We set up an eco-balance of the working systems of intermediate cutting and final harvest in the stands of beech, oak, spruce, acacia, poplar and short rotation energy plantations (willow, poplar). We set up the life-cycle plan of the surveyed working systems by using the GaBi 6.0 Professional software and carried out midpoint and endpoint impact assessment. Out of the results, we applied the values of CML 2001 - Global Warming Potential (GWP 100 years) [kg CO2-Equiv.] and Eco-Indicator 99 - Human health, Climate Change [DALY]. On the basis of the values we set up a ranking of technology. By this, we received the environmental impact classification of the technologies based on carbon footprint. The working systems had the greatest impact on global warming (GWP 100 years) throughout their whole life cycle. This is explained by the amount of carbon dioxide releasing to the atmosphere resulting from the fuel of the technologies. Abiotic depletion (ADP foss) and marine aquatic ecotoxicity (MAETP) emerged also as significant impact categories. These impact categories can be explained by the share of input of fuel and lube. On the basis of the most significant environmental impact category (carbon footprint), we perform the relative life cycle contribution and ranking of each technologies. The technological life cycle stages examined in the stands are the followings: Stage 1. cleaning cutting Stage 2. selection thinning Stage 3. increment thinning Stage 4. final harvest In these priority impact categories, the life cycle contribution of technologies varied according to the life cycle stages. • The spruce stand showed the smallest contribution in the stages 1, 2, 3 alike. • After the large contribution of beech stand at the beginning (stage 1), it continues representing a moderate level in stage 2 and 3, and it shares the smallest rate in final harvest (stage 4). • The oak stand showed the largest contribution in the stages 2, 3, 4 alike. • In the case of acacia and poplar, we have got the same results as in the case of oak stands. • In the case of short rotation energy plantations (willow, poplar), we got the results typical on stage 4 of spruce stands. We can conclude, that in case of the stage of final harvest, which represents the most significant environmental impact, the ranking of working systems showes the increasing order of „energy plantations - beech - spruce - acacia - poplar - oak". The environmental assessment of technological aspects of land use and land use change represent an important added value to the climate research. Acknowledgement: This research has been supported by the Agroclimate.2 VKSZ_12-1- 2013-0034 project. Keywords: life-cycle assessment / forest utilization technology / carbon footprint / life-cycle thinking

A Science and Risk-Based Pragmatic Methodology for Blend and Content Uniformity Assessment.

PubMed

Sayeed-Desta, Naheed; Pazhayattil, Ajay Babu; Collins, Jordan; Doshi, Chetan

2018-04-01

This paper describes a pragmatic approach that can be applied in assessing powder blend and unit dosage uniformity of solid dose products at Process Design, Process Performance Qualification, and Continued/Ongoing Process Verification stages of the Process Validation lifecycle. The statistically based sampling, testing, and assessment plan was developed due to the withdrawal of the FDA draft guidance for industry "Powder Blends and Finished Dosage Units-Stratified In-Process Dosage Unit Sampling and Assessment." This paper compares the proposed Grouped Area Variance Estimate (GAVE) method with an alternate approach outlining the practicality and statistical rationalization using traditional sampling and analytical methods. The approach is designed to fit solid dose processes assuring high statistical confidence in both powder blend uniformity and dosage unit uniformity during all three stages of the lifecycle complying with ASTM standards as recommended by the US FDA.

Towards a Lifecycle Information Framework and Technology in Manufacturing.

PubMed

Hedberg, Thomas; Feeney, Allison Barnard; Helu, Moneer; Camelio, Jaime A

2017-06-01

Industry has been chasing the dream of integrating and linking data across the product lifecycle and enterprises for decades. However, industry has been challenged by the fact that the context in which data is used varies based on the function / role in the product lifecycle that is interacting with the data. Holistically, the data across the product lifecycle must be considered an unstructured data-set because multiple data repositories and domain-specific schema exist in each phase of the lifecycle. This paper explores a concept called the Lifecycle Information Framework and Technology (LIFT). LIFT is a conceptual framework for lifecycle information management and the integration of emerging and existing technologies, which together form the basis of a research agenda for dynamic information modeling in support of digital-data curation and reuse in manufacturing. This paper provides a discussion of the existing technologies and activities that the LIFT concept leverages. Also, the paper describes the motivation for applying such work to the domain of manufacturing. Then, the LIFT concept is discussed in detail, while underlying technologies are further examined and a use case is detailed. Lastly, potential impacts are explored.

The integration of the risk management process with the lifecycle of medical device software.

PubMed

Pecoraro, F; Luzi, D

2014-01-01

The application of software in the Medical Device (MD) domain has become central to the improvement of diagnoses and treatments. The new European regulations that specifically address software as an important component of MD, require complex procedures to make software compliant with safety requirements, introducing thereby new challenges in the qualification and classification of MD software as well as in the performance of risk management activities. Under this perspective, the aim of this paper is to propose an integrated framework that combines the activities to be carried out by the manufacturer to develop safe software within the development lifecycle based on the regulatory requirements reported in US and European regulations as well as in the relevant standards and guidelines. A comparative analysis was carried out to identify the main issues related to the application of the current new regulations. In addition, standards and guidelines recently released to harmonise procedures for the validation of MD software have been used to define the risk management activities to be carried out by the manufacturer during the software development process. This paper highlights the main issues related to the qualification and classification of MD software, providing an analysis of the different regulations applied in Europe and the US. A model that integrates the risk management process within the software development lifecycle has been proposed too. It is based on regulatory requirements and considers software risk analysis as a central input to be managed by the manufacturer already at the initial stages of the software design, in order to prevent MD failures. Relevant changes in the process of MD development have been introduced with the recognition of software being an important component of MDs as stated in regulations and standards. This implies the performance of highly iterative processes that have to integrate the risk management in the framework of software development. It also makes it necessary to involve both medical and software engineering competences to safeguard patient and user safety.

Training Module on the Development of Best Modeling Practices

EPA Pesticide Factsheets

This module continues the fundamental concepts outlined in the previous modules. Objectives are to identify the ‘best modeling practices’ and strategies for the Development Stage of the model life-cycle and define the steps of model development.

The activities of current antimalarial drugs on the life cycle stages of Plasmodium: a comparative study with human and rodent parasites.

PubMed

Delves, Michael; Plouffe, David; Scheurer, Christian; Meister, Stephan; Wittlin, Sergio; Winzeler, Elizabeth A; Sinden, Robert E; Leroy, Didier

2012-02-01

Malaria remains a disease of devastating global impact, killing more than 800,000 people every year-the vast majority being children under the age of 5. While effective therapies are available, if malaria is to be eradicated a broader range of small molecule therapeutics that are able to target the liver and the transmissible sexual stages are required. These new medicines are needed both to meet the challenge of malaria eradication and to circumvent resistance. Little is known about the wider stage-specific activities of current antimalarials that were primarily designed to alleviate symptoms of malaria in the blood stage. To overcome this critical gap, we developed assays to measure activity of antimalarials against all life stages of malaria parasites, using a diverse set of human and nonhuman parasite species, including male gamete production (exflagellation) in Plasmodium falciparum, ookinete development in P. berghei, oocyst development in P. berghei and P. falciparum, and the liver stage of P. yoelii. We then compared 50 current and experimental antimalarials in these assays. We show that endoperoxides such as OZ439, a stable synthetic molecule currently in clinical phase IIa trials, are strong inhibitors of gametocyte maturation/gamete formation and impact sporogony; lumefantrine impairs development in the vector; and NPC-1161B, a new 8-aminoquinoline, inhibits sporogony. These data enable objective comparisons of the strengths and weaknesses of each chemical class at targeting each stage of the lifecycle. Noting that the activities of many compounds lie within achievable blood concentrations, these results offer an invaluable guide to decisions regarding which drugs to combine in the next-generation of antimalarial drugs. This study might reveal the potential of life-cycle-wide analyses of drugs for other pathogens with complex life cycles.

Improved Predictions of the Geographic Distribution of Invasive Plants Using Climatic Niche Models.

PubMed

Ramírez-Albores, Jorge E; Bustamante, Ramiro O; Badano, Ernesto I

2016-01-01

Climatic niche models for invasive plants are usually constructed with occurrence records taken from literature and collections. Because these data neither discriminate among life-cycle stages of plants (adult or juvenile) nor the origin of individuals (naturally established or man-planted), the resulting models may mispredict the distribution ranges of these species. We propose that more accurate predictions could be obtained by modelling climatic niches with data of naturally established individuals, particularly with occurrence records of juvenile plants because this would restrict the predictions of models to those sites where climatic conditions allow the recruitment of the species. To test this proposal, we focused on the Peruvian peppertree (Schinus molle), a South American species that has largely invaded Mexico. Three climatic niche models were constructed for this species using high-resolution dataset gathered in the field. The first model included all occurrence records, irrespective of the life-cycle stage or origin of peppertrees (generalized niche model). The second model only included occurrence records of naturally established mature individuals (adult niche model), while the third model was constructed with occurrence records of naturally established juvenile plants (regeneration niche model). When models were compared, the generalized climatic niche model predicted the presence of peppertrees in sites located farther beyond the climatic thresholds that naturally established individuals can tolerate, suggesting that human activities influence the distribution of this invasive species. The adult and regeneration climatic niche models concurred in their predictions about the distribution of peppertrees, suggesting that naturally established adult trees only occur in sites where climatic conditions allow the recruitment of juvenile stages. These results support the proposal that climatic niches of invasive plants should be modelled with data of naturally established individuals because this improves the accuracy of predictions about their distribution ranges.

Improved Predictions of the Geographic Distribution of Invasive Plants Using Climatic Niche Models

PubMed Central

Ramírez-Albores, Jorge E.; Bustamante, Ramiro O.

2016-01-01

Climatic niche models for invasive plants are usually constructed with occurrence records taken from literature and collections. Because these data neither discriminate among life-cycle stages of plants (adult or juvenile) nor the origin of individuals (naturally established or man-planted), the resulting models may mispredict the distribution ranges of these species. We propose that more accurate predictions could be obtained by modelling climatic niches with data of naturally established individuals, particularly with occurrence records of juvenile plants because this would restrict the predictions of models to those sites where climatic conditions allow the recruitment of the species. To test this proposal, we focused on the Peruvian peppertree (Schinus molle), a South American species that has largely invaded Mexico. Three climatic niche models were constructed for this species using high-resolution dataset gathered in the field. The first model included all occurrence records, irrespective of the life-cycle stage or origin of peppertrees (generalized niche model). The second model only included occurrence records of naturally established mature individuals (adult niche model), while the third model was constructed with occurrence records of naturally established juvenile plants (regeneration niche model). When models were compared, the generalized climatic niche model predicted the presence of peppertrees in sites located farther beyond the climatic thresholds that naturally established individuals can tolerate, suggesting that human activities influence the distribution of this invasive species. The adult and regeneration climatic niche models concurred in their predictions about the distribution of peppertrees, suggesting that naturally established adult trees only occur in sites where climatic conditions allow the recruitment of juvenile stages. These results support the proposal that climatic niches of invasive plants should be modelled with data of naturally established individuals because this improves the accuracy of predictions about their distribution ranges. PMID:27195983

Training Module on the Evaluation of Best Modeling Practices

EPA Pesticide Factsheets

Building upon the fundamental concepts outlined in previous modules, the objectives of this module are to explore the topic of model evaluation and identify the 'best modeling practices' and strategies for the Evaluation Stage of the model life-cycle.

Lys48 ubiquitination during the intraerythrocytic cycle of the rodent malaria parasite, Plasmodium chabaudi.

PubMed

González-López, Lorena; Carballar-Lejarazú, Rebeca; Arrevillaga Boni, Gerardo; Cortés-Martínez, Leticia; Cázares-Raga, Febe Elena; Trujillo-Ocampo, Abel; Rodríguez, Mario H; James, Anthony A; Hernández-Hernández, Fidel de la Cruz

2017-01-01

Ubiquitination tags proteins for different functions within the cell. One of the most abundant and studied ubiquitin modification is the Lys48 polyubiquitin chain that modifies proteins for their destruction by proteasome. In Plasmodium is proposed that post-translational regulation is fundamental for parasite development during its complex life-cycle; thus, the objective of this work was to analyze the ubiquitination during Plasmodium chabaudi intraerythrocytic stages. Ubiquitinated proteins were detected during intraerythrocytic stages of Plasmodium chabaudi by immunofluorescent microscopy, bidimensional electrophoresis (2-DE) combined with immunoblotting and mass spectrometry. All the studied stages presented protein ubiquitination and Lys48 polyubiquitination with more abundance during the schizont stage. Three ubiquitinated proteins were identified for rings, five for trophozoites and twenty for schizonts. Only proteins detected with a specific anti- Lys48 polyubiquitin antibody were selected for Mass Spectrometry analysis and two of these identified proteins were selected in order to detect the specific amino acid residues where ubiquitin is placed. Ubiquitinated proteins during the ring and trophozoite stages were related with the invasion process and in schizont proteins were related with nucleic acid metabolism, glycolysis and protein biosynthesis. Most of the ubiquitin detection was during the schizont stage and the Lys48 polyubiquitination during this stage was related to proteins that are expected to be abundant during the trophozoite stage. The evidence that these Lys48 polyubiquitinated proteins are tagged for destruction by the proteasome complex suggests that this type of post-translational modification is important in the regulation of protein abundance during the life-cycle and may also contribute to the parasite cell-cycle progression.

Towards a Lifecycle Information Framework and Technology in Manufacturing

PubMed Central

Hedberg, Thomas; Feeney, Allison Barnard; Helu, Moneer; Camelio, Jaime A.

2016-01-01

Industry has been chasing the dream of integrating and linking data across the product lifecycle and enterprises for decades. However, industry has been challenged by the fact that the context in which data is used varies based on the function / role in the product lifecycle that is interacting with the data. Holistically, the data across the product lifecycle must be considered an unstructured data-set because multiple data repositories and domain-specific schema exist in each phase of the lifecycle. This paper explores a concept called the Lifecycle Information Framework and Technology (LIFT). LIFT is a conceptual framework for lifecycle information management and the integration of emerging and existing technologies, which together form the basis of a research agenda for dynamic information modeling in support of digital-data curation and reuse in manufacturing. This paper provides a discussion of the existing technologies and activities that the LIFT concept leverages. Also, the paper describes the motivation for applying such work to the domain of manufacturing. Then, the LIFT concept is discussed in detail, while underlying technologies are further examined and a use case is detailed. Lastly, potential impacts are explored. PMID:28265224

Assessing Marine Species Exposure to Ocean Acidification

NASA Astrophysics Data System (ADS)

Jewett, E.; Busch, S.; McElhany, P.; Gledhill, D. K.; Milke, L. M.; Wieczorek, D.

2016-02-01

Assessing the vulnerability of society to ocean acidification (OA) demands an understanding of both the sensitivity of economically important species together with an organism's exposure to potentially harmful carbonate chemistry conditions. However, research has revealed that sensitivity to OA is frequently life-stage dependent and the environmental conditions experienced by a marine organism often vary with life-stage. Enhancing the development of a National Ocean Acidification Observing Network (NOA-ON) and establishing appropriate treatment conditions for experimental studies requires careful consideration of where the vulnerable life-stages of an organism reside in space (e.g., estuary versus oceanic), depth (e.g., surface mixed layer versus benthos), and time (e.g., diel vertical migration, seasonality of the chemical environment within the context of an organism life cycle). Few studies have explicitly attempted to document carbonate chemistry dynamics specific to a given organism's life-cycle. Here we estimate carbonate dynamics in terms of aragonite saturation state range and variability within the U.S. Northeast and West Coast through the application of NOAA's NOA-ON assets mapped out with respect to the life stages of economically important species within those regions. Two economically important species will be considered for which the life-cycles are well known along with the sensitivities to OA for early life-stages: Atlantic Surf Clam in the northeast and Dungeness Crab of the northwest coast of the U.S. Other species may also be considered.

Towards clinical development of a Pfs48/45-based transmission blocking malaria vaccine.

PubMed

Theisen, Michael; Jore, Matthijs M; Sauerwein, Robert

2017-04-01

Malaria is a devastating vector-borne disease caused by the Plasmodium parasite, resulting in almost 0.5 million casualties per year. The parasite has a complex life-cycle that includes asexual replication in human red blood cells, causing symptomatic malaria, and sexual stages which are essential for the transmission to the mosquito vector. A vaccine targeting the sexual stages of the parasite and thus blocking transmission will be instrumental for the eradication of malaria. One of the leading transmission blocking vaccine candidates is the sexual stage antigen Pfs48/45. Areas covered: PubMed was searched to review the progress and future prospects for clinical development of a Pfs48/45-based subunit vaccine. We will focus on biological function, naturally acquired immunity, functional activity of specific antibodies, sequence diversity, production of recombinant protein and preclinical studies. Expert commentary: Pfs48/45 is one of the lead-candidates for a transmission blocking vaccine and should be further explored in clinical trials.

Classifying stages of cirrus life-cycle evolution

NASA Astrophysics Data System (ADS)

Urbanek, Benedikt; Groß, Silke; Schäfler, Andreas; Wirth, Martin

2018-04-01

Airborne lidar backscatter data is used to determine in- and out-of-cloud regions. Lidar measurements of water vapor together with model temperature fields are used to calculate relative humidity over ice (RHi). Based on temperature and RHi we identify different stages of cirrus evolution: homogeneous and heterogeneous freezing, depositional growth, ice sublimation and sedimentation. We will present our classification scheme and first applications on mid-latitude cirrus clouds.

Generalized fish life-cycle poplulation model and computer program

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeAngelis, D. L.; Van Winkle, W.; Christensen, S. W.

1978-03-01

A generalized fish life-cycle population model and computer program have been prepared to evaluate the long-term effect of changes in mortality in age class 0. The general question concerns what happens to a fishery when density-independent sources of mortality are introduced that act on age class 0, particularly entrainment and impingement at power plants. This paper discusses the model formulation and computer program, including sample results. The population model consists of a system of difference equations involving age-dependent fecundity and survival. The fecundity for each age class is assumed to be a function of both the fraction of females sexuallymore » mature and the weight of females as they enter each age class. Natural mortality for age classes 1 and older is assumed to be independent of population size. Fishing mortality is assumed to vary with the number and weight of fish available to the fishery. Age class 0 is divided into six life stages. The probability of survival for age class 0 is estimated considering both density-independent mortality (natural and power plant) and density-dependent mortality for each life stage. Two types of density-dependent mortality are included. These are cannibalism of each life stage by older age classes and intra-life-stage competition.« less

Making Evidence Work: A Framework for Monitoring, Tracking and Evaluating Widening Participation Activity across the Student Lifecycle

ERIC Educational Resources Information Center

Raven, Neil

2016-01-01

The need for a robust evidence base able to demonstrate the impact of widening participation activity across the student lifecycle has been emphasised in recent guidance to the higher education sector. However, with competing demands on their time this is likely to represent a challenge for practitioners. Yet, there is wide recognition of the need…

Semantic Modeling of Requirements: Leveraging Ontologies in Systems Engineering

ERIC Educational Resources Information Center

Mir, Masood Saleem

2012-01-01

The interdisciplinary nature of "Systems Engineering" (SE), having "stakeholders" from diverse domains with orthogonal facets, and need to consider all stages of "lifecycle" of system during conception, can benefit tremendously by employing "Knowledge Engineering" (KE) to achieve semantic agreement among all…

Comparative Analysis of the Secretome from a Model Filarial Nematode (Litomosoides sigmodontis) Reveals Maximal Diversity in Gravid Female Parasites*

PubMed Central

Armstrong, Stuart D.; Babayan, Simon A.; Lhermitte-Vallarino, Nathaly; Gray, Nick; Xia, Dong; Martin, Coralie; Kumar, Sujai; Taylor, David W.; Blaxter, Mark L.; Wastling, Jonathan M.; Makepeace, Benjamin L.

2014-01-01

Filarial nematodes (superfamily Filarioidea) are responsible for an annual global health burden of ∼6.3 million disability-adjusted life-years, which represents the greatest single component of morbidity attributable to helminths affecting humans. No vaccine exists for the major filarial diseases, lymphatic filariasis and onchocerciasis; in part because research on protective immunity against filariae has been constrained by the inability of the human-parasitic species to complete their lifecycles in laboratory mice. However, the rodent filaria Litomosoides sigmodontis has become a popular experimental model, as BALB/c mice are fully permissive for its development and reproduction. Here, we provide a comprehensive analysis of excretory-secretory products from L. sigmodontis across five lifecycle stages and identifications of host proteins associated with first-stage larvae (microfilariae) in the blood. Applying intensity-based quantification, we determined the abundance of 302 unique excretory-secretory proteins, of which 64.6% were present in quantifiable amounts only from gravid adult female nematodes. This lifecycle stage, together with immature microfilariae, released four proteins that have not previously been evaluated as vaccine candidates: a predicted 28.5 kDa filaria-specific protein, a zonadhesin and SCO-spondin-like protein, a vitellogenin, and a protein containing six metridin-like ShK toxin domains. Female nematodes also released two proteins derived from the obligate Wolbachia symbiont. Notably, excretory-secretory products from all parasite stages contained several uncharacterized members of the transthyretin-like protein family. Furthermore, biotin labeling revealed that redox proteins and enzymes involved in purinergic signaling were enriched on the adult nematode cuticle. Comparison of the L. sigmodontis adult secretome with that of the human-infective filarial nematode Brugia malayi (reported previously in three independent published studies) identified differences that suggest a considerable underlying diversity of potential immunomodulators. The molecules identified in L. sigmodontis excretory-secretory products show promise not only for vaccination against filarial infections, but for the amelioration of allergy and autoimmune diseases. PMID:24958169

Cathepsin Gene Family Reveals Transcriptome Patterns Related to the Infective Stages of the Salmon Louse Caligus rogercresseyi

PubMed Central

Maldonado-Aguayo, Waleska; Chávez-Mardones, Jacqueline; Gonçalves, Ana Teresa; Gallardo-Escárate, Cristian

2015-01-01

Cathepsins are proteases involved in the ability of parasites to overcome and/or modulate host defenses so as to complete their own lifecycle. However, the mechanisms underlying this ability of cathepsins are still poorly understood. One excellent model for identifying and exploring the molecular functions of cathepsins is the marine ectoparasitic copepod Caligus rogercresseyi that currently affects the Chilean salmon industry. Using high-throughput transcriptome sequencing, 56 cathepsin-like sequences were found distributed in five cysteine protease groups (B, F, L, Z, and S) as well as in an aspartic protease group (D). Ontogenic transcriptome analysis evidenced that L cathepsins were the most abundant during the lifecycle, while cathepsins B and K were mostly expressed in the larval stages and adult females, thus suggesting participation in the molting processes and embryonic development, respectively. Interestingly, a variety of cathepsins from groups Z, L, D, B, K, and S were upregulated in the infective stage of copepodid, corroborating the complexity of the processes involved in the parasitic success of this copepod. Putative functional roles of cathepsins were conjectured based on the differential expressions found and on roles previously described in other phylogenetically related species. Moreover, 140 single nucleotide polymorphisms (SNP) were identified in transcripts annotated for cysteine and aspartic proteases located into untranslated regions, or the coding region. This study reports for the first time the presence of cathepsin-like genes and differential expressions throughout a copepod lifecycle. The identification of cathepsins together with functional validations represents a valuable strategy for pinpointing target molecules that could be used in the development of new delousing drugs or vaccines against C. rogercresseyi. PMID:25923525

Cathepsin Gene Family Reveals Transcriptome Patterns Related to the Infective Stages of the Salmon Louse Caligus rogercresseyi.

PubMed

Maldonado-Aguayo, Waleska; Chávez-Mardones, Jacqueline; Gonçalves, Ana Teresa; Gallardo-Escárate, Cristian

2015-01-01

Cathepsins are proteases involved in the ability of parasites to overcome and/or modulate host defenses so as to complete their own lifecycle. However, the mechanisms underlying this ability of cathepsins are still poorly understood. One excellent model for identifying and exploring the molecular functions of cathepsins is the marine ectoparasitic copepod Caligus rogercresseyi that currently affects the Chilean salmon industry. Using high-throughput transcriptome sequencing, 56 cathepsin-like sequences were found distributed in five cysteine protease groups (B, F, L, Z, and S) as well as in an aspartic protease group (D). Ontogenic transcriptome analysis evidenced that L cathepsins were the most abundant during the lifecycle, while cathepsins B and K were mostly expressed in the larval stages and adult females, thus suggesting participation in the molting processes and embryonic development, respectively. Interestingly, a variety of cathepsins from groups Z, L, D, B, K, and S were upregulated in the infective stage of copepodid, corroborating the complexity of the processes involved in the parasitic success of this copepod. Putative functional roles of cathepsins were conjectured based on the differential expressions found and on roles previously described in other phylogenetically related species. Moreover, 140 single nucleotide polymorphisms (SNP) were identified in transcripts annotated for cysteine and aspartic proteases located into untranslated regions, or the coding region. This study reports for the first time the presence of cathepsin-like genes and differential expressions throughout a copepod lifecycle. The identification of cathepsins together with functional validations represents a valuable strategy for pinpointing target molecules that could be used in the development of new delousing drugs or vaccines against C. rogercresseyi.

Effects of rearing temperature on immune functions in sockeye salmon (Oncorhynchus nerka)

USGS Publications Warehouse

Alcorn, S.W.; Murray, A.L.; Pascho, R.J.

2002-01-01

To determine if the defences of sockeye salmon (Oncorhynchus nerka) raised in captivity are affected by the rearing temperature or their life-cycle stage, various indices of the humoral and cellular immune functions were measured in fish reared at either 8 or 12??C for their entire life-cycle. Measures of humoral immunity included the commonly used haematological parameters, as well as measurements of complement, and lysozyme activity. Cellular assays quantified the ability of macrophages from the anterior kidney to phagocytise Staphylococcus aureus cells, or the activities of certain bactericidal systems of those cells. The T-dependent antibody response to a recombinant 57 kDa protein of Renibacterium salmoninarum was used to quantify the specific immune response. Fish were sampled during the spring and fall of their second, third and fourth years, corresponding to a period that began just before smolting and ended at sexual maturation. Fish reared at 8??C tended to have a greater percentage of phagocytic kidney macrophages during the first 2 years of sampling than the fish reared at 12??C. During the last half of the study the complement activity of the fish reared at 8??C was greater than that of the 12??C fish. Conversely, a greater proportion of the blood leucocytes were lymphocytes in fish reared at 12??C compared to the fish reared at 8??C. Fish reared at 12??C also produced a greater antibody response than those reared at 8??C. Results suggested that the immune apparatus of sockeye salmon reared at 8??C relied more heavily on the non-specific immune response, while the specific immune response was used to a greater extent when the fish were reared at 12??C. Although a seasonal effect was not detected in any of the indices measured, varying effects were observed in some measurements during sexual maturation of fish in both temperature groups. At that time there were dramatic decreases in complement activity and lymphocyte numbers. This study was unique in its scope because it was the first quantitative assessment of salmon immune functions for an entire life-cycle. ?? 2002 Elsevier Science Ltd.

Method refinements for the midge life-cycle, Chironomus dilutus test

EPA Science Inventory

Larval stages of non-biting midges can be found in almost any freshwater ecosystem, and one of the commonly tested midges is Chironomus dilutus (Chironomidae, Diptera) which is used for toxicity testing and ecological risk assessment of freshwater contaminants. USEPA, ASTM, Envir...

The Psychology of Career Theory--A New Perspective?

ERIC Educational Resources Information Center

Woodd, Maureen

2000-01-01

New perspectives on human behavior have invalidated some assumptions of career theories such as personality type, career stages, and life-cycle models. Other theories, such as Driver's Objective Career Patterns, Schein's Temporal Development Model, and Nicholson's Transition Cycle, are compatible with current psychological understanding. (SK)

Best practices: Product category rule creation and use

EPA Science Inventory

Benefits of life cycle-based claims For most products, the majority of impact occurs upstream or downstream of product use . Single-stage claims for products (e.g., recycled content; energy efficient) don’t capture the relevance of that attribute in life-cycle environmental per...

The Vapor-phase Multi-stage CMD Test for Characterizing Contaminant Mass Discharge Associated with VOC Sources in the Vadose Zone: Application to Three Sites in Different Lifecycle Stages of SVE Operations

PubMed Central

Brusseau, M.L.; Mainhagu, J.; Morrison, C.; Carroll, K.C.

2015-01-01

Vapor-phase multi-stage contaminant mass discharge (CMD) tests were conducted at three field sites to measure mass discharge associated with contaminant sources located in the vadose zone. The three sites represent the three primary stages along the soil vapor extraction (SVE) operations lifecycle- pre/initial-SVE, mid-lifecycle, and near-closure. A CMD of 32 g/d was obtained for a site at which soil vapor SVE has been in operation for approximately 6 years, and for which mass removal is currently in the asymptotic stage. The contaminant removal behavior exhibited for the vapor extractions conducted at this site suggests that there is unlikely to be a significant mass of non-vapor-phase contaminant (e.g., DNAPL, sorbed phase) remaining in the advective domains, and that most remaining mass is likely located in poorly accessible domains. Given the conditions for this site, this remaining mass is hypothesized to be associated with the low-permeability (and higher water saturation) region in the vicinity of the saturated zone and capillary fringe. A CMD of 25 g/d was obtained for a site wherein SVE has been in operation for several years but concentrations and mass-removal rates are still relatively high. A CMD of 270 g/d was obtained for a site for which there were no prior SVE operations. The behavior exhibited for the vapor extractions conducted at this site suggest that non-vapor-phase contaminant mass (e.g., DNAPL) may be present in the advective domains. Hence, the asymptotic conditions observed for this site most likely derive from a combination of rate-limited mass transfer from DNAPL (and sorbed) phases present in the advective domain as well as mass residing in lower-permeability (“non-advective”) regions. The CMD values obtained from the tests were used in conjunction with a recently developed vapor-discharge tool to evaluate the impact of the measured CMDs on groundwater quality. PMID:26047819

Modelling the impact of vector control interventions on Anopheles gambiae population dynamics

PubMed Central

2011-01-01

Background Intensive anti-malaria campaigns targeting the Anopheles population have demonstrated substantial reductions in adult mosquito density. Understanding the population dynamics of Anopheles mosquitoes throughout their whole lifecycle is important to assess the likely impact of vector control interventions alone and in combination as well as to aid the design of novel interventions. Methods An ecological model of Anopheles gambiae sensu lato populations incorporating a rainfall-dependent carrying capacity and density-dependent regulation of mosquito larvae in breeding sites is developed. The model is fitted to adult mosquito catch and rainfall data from 8 villages in the Garki District of Nigeria (the 'Garki Project') using Bayesian Markov Chain Monte Carlo methods and prior estimates of parameters derived from the literature. The model is used to compare the impact of vector control interventions directed against adult mosquito stages - long-lasting insecticide treated nets (LLIN), indoor residual spraying (IRS) - and directed against aquatic mosquito stages, alone and in combination on adult mosquito density. Results A model in which density-dependent regulation occurs in the larval stages via a linear association between larval density and larval death rates provided a good fit to seasonal adult mosquito catches. The effective mosquito reproduction number in the presence of density-dependent regulation is dependent on seasonal rainfall patterns and peaks at the start of the rainy season. In addition to killing adult mosquitoes during the extrinsic incubation period, LLINs and IRS also result in less eggs being oviposited in breeding sites leading to further reductions in adult mosquito density. Combining interventions such as the application of larvicidal or pupacidal agents that target the aquatic stages of the mosquito lifecycle with LLINs or IRS can lead to substantial reductions in adult mosquito density. Conclusions Density-dependent regulation of anopheline larvae in breeding sites ensures robust, stable mosquito populations that can persist in the face of intensive vector control interventions. Selecting combinations of interventions that target different stages in the vector's lifecycle will result in maximum reductions in mosquito density. PMID:21798055

The vapor-phase multi-stage CMD test for characterizing contaminant mass discharge associated with VOC sources in the vadose zone: Application to three sites in different lifecycle stages of SVE operations.

PubMed

Brusseau, M L; Mainhagu, J; Morrison, C; Carroll, K C

2015-08-01

Vapor-phase multi-stage contaminant mass discharge (CMD) tests were conducted at three field sites to measure mass discharge associated with contaminant sources located in the vadose zone. The three sites represent the three primary stages of the soil vapor extraction (SVE) operations lifecycle-pre/initial-SVE, mid-lifecycle, and near-closure. A CMD of 32g/d was obtained for a site at which soil vapor SVE has been in operation for approximately 6years, and for which mass removal is currently in the asymptotic stage. The contaminant removal behavior exhibited for the vapor extractions conducted at this site suggests that there is unlikely to be a significant mass of non-vapor-phase contaminant (e.g., DNAPL, sorbed phase) remaining in the advective domains, and that most remaining mass is likely located in poorly accessible domains. Given the conditions for this site, this remaining mass is hypothesized to be associated with the low-permeability (and higher water saturation) region in the vicinity of the saturated zone and capillary fringe. A CMD of 25g/d was obtained for a site wherein SVE has been in operation for several years but concentrations and mass-removal rates are still relatively high. A CMD of 270g/d was obtained for a site for which there were no prior SVE operations. The behavior exhibited for the vapor extractions conducted at this site suggest that non-vapor-phase contaminant mass (e.g., DNAPL) may be present in the advective domains. Hence, the asymptotic conditions observed for this site most likely derive from a combination of rate-limited mass transfer from DNAPL (and sorbed) phases present in the advective domain as well as mass residing in lower-permeability ("non-advective") regions. The CMD values obtained from the tests were used in conjunction with a recently developed vapor-discharge tool to evaluate the impact of the measured CMDs on groundwater quality. Copyright © 2015 Elsevier B.V. All rights reserved.

Life-cycle greenhouse gas emissions of shale gas, natural gas, coal, and petroleum.

PubMed

Burnham, Andrew; Han, Jeongwoo; Clark, Corrie E; Wang, Michael; Dunn, Jennifer B; Palou-Rivera, Ignasi

2012-01-17

The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. It has been debated whether the fugitive methane emissions during natural gas production and transmission outweigh the lower carbon dioxide emissions during combustion when compared to coal and petroleum. Using the current state of knowledge of methane emissions from shale gas, conventional natural gas, coal, and petroleum, we estimated up-to-date life-cycle greenhouse gas emissions. In addition, we developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings that need to be further addressed. Our base case results show that shale gas life-cycle emissions are 6% lower than conventional natural gas, 23% lower than gasoline, and 33% lower than coal. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty whether shale gas emissions are indeed lower than conventional gas. Moreover, this life-cycle analysis, among other work in this area, provides insight on critical stages that the natural gas industry and government agencies can work together on to reduce the greenhouse gas footprint of natural gas.

Secure it now or secure it later: the benefits of addressing cyber-security from the outset

NASA Astrophysics Data System (ADS)

Olama, Mohammed M.; Nutaro, James

2013-05-01

The majority of funding for research and development (R&D) in cyber-security is focused on the end of the software lifecycle where systems have been deployed or are nearing deployment. Recruiting of cyber-security personnel is similarly focused on end-of-life expertise. By emphasizing cyber-security at these late stages, security problems are found and corrected when it is most expensive to do so, thus increasing the cost of owning and operating complex software systems. Worse, expenditures on expensive security measures often mean less money for innovative developments. These unwanted increases in cost and potential slowing of innovation are unavoidable consequences of an approach to security that finds and remediate faults after software has been implemented. We argue that software security can be improved and the total cost of a software system can be substantially reduced by an appropriate allocation of resources to the early stages of a software project. By adopting a similar allocation of R&D funds to the early stages of the software lifecycle, we propose that the costs of cyber-security can be better controlled and, consequently, the positive effects of this R&D on industry will be much more pronounced.

Stakeholder requirements for commercially successful wave energy converter farms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babarit, Aurélien; Bull, Diana; Dykes, Katherine

2017-12-01

In this study, systems engineering techniques are applied to wave energy to identify and specify stakeholders' requirements for a commercially successful wave energy farm. The focus is on the continental scale utility market. Lifecycle stages and stakeholders are identified. Stakeholders' needs across the whole lifecycle of the wave energy farm are analyzed. A list of 33 stakeholder requirements are identified and specified. This list of requirements should serve as components of a technology performance level metric that could be used by investors and funding agencies to make informed decisions when allocating resources. It is hoped that the technology performance levelmore » metric will accelerate wave energy conversion technology convergence.« less

Lifecycle Librarianship

ERIC Educational Resources Information Center

Crowley, Bill

2008-01-01

In a time when information self-service and enhanced competition have sent libraries of all types into an oftentimes desperate search for a renewed sense of purpose, a fundamentally important question takes center stage: How can libraries connect with the deepest aspirations of their service communities? This article describes a new library…

Getting more out of biomedical documents with GATE's full lifecycle open source text analytics.

PubMed

Cunningham, Hamish; Tablan, Valentin; Roberts, Angus; Bontcheva, Kalina

2013-01-01

This software article describes the GATE family of open source text analysis tools and processes. GATE is one of the most widely used systems of its type with yearly download rates of tens of thousands and many active users in both academic and industrial contexts. In this paper we report three examples of GATE-based systems operating in the life sciences and in medicine. First, in genome-wide association studies which have contributed to discovery of a head and neck cancer mutation association. Second, medical records analysis which has significantly increased the statistical power of treatment/outcome models in the UK's largest psychiatric patient cohort. Third, richer constructs in drug-related searching. We also explore the ways in which the GATE family supports the various stages of the lifecycle present in our examples. We conclude that the deployment of text mining for document abstraction or rich search and navigation is best thought of as a process, and that with the right computational tools and data collection strategies this process can be made defined and repeatable. The GATE research programme is now 20 years old and has grown from its roots as a specialist development tool for text processing to become a rather comprehensive ecosystem, bringing together software developers, language engineers and research staff from diverse fields. GATE now has a strong claim to cover a uniquely wide range of the lifecycle of text analysis systems. It forms a focal point for the integration and reuse of advances that have been made by many people (the majority outside of the authors' own group) who work in text processing for biomedicine and other areas. GATE is available online <1> under GNU open source licences and runs on all major operating systems. Support is available from an active user and developer community and also on a commercial basis.

Getting More Out of Biomedical Documents with GATE's Full Lifecycle Open Source Text Analytics

PubMed Central

Cunningham, Hamish; Tablan, Valentin; Roberts, Angus; Bontcheva, Kalina

2013-01-01

This software article describes the GATE family of open source text analysis tools and processes. GATE is one of the most widely used systems of its type with yearly download rates of tens of thousands and many active users in both academic and industrial contexts. In this paper we report three examples of GATE-based systems operating in the life sciences and in medicine. First, in genome-wide association studies which have contributed to discovery of a head and neck cancer mutation association. Second, medical records analysis which has significantly increased the statistical power of treatment/outcome models in the UK's largest psychiatric patient cohort. Third, richer constructs in drug-related searching. We also explore the ways in which the GATE family supports the various stages of the lifecycle present in our examples. We conclude that the deployment of text mining for document abstraction or rich search and navigation is best thought of as a process, and that with the right computational tools and data collection strategies this process can be made defined and repeatable. The GATE research programme is now 20 years old and has grown from its roots as a specialist development tool for text processing to become a rather comprehensive ecosystem, bringing together software developers, language engineers and research staff from diverse fields. GATE now has a strong claim to cover a uniquely wide range of the lifecycle of text analysis systems. It forms a focal point for the integration and reuse of advances that have been made by many people (the majority outside of the authors' own group) who work in text processing for biomedicine and other areas. GATE is available online <1> under GNU open source licences and runs on all major operating systems. Support is available from an active user and developer community and also on a commercial basis. PMID:23408875

ALTERATIONS IN THE ENERGY METABOLISM OF AN ESTUARINE MYSID (MYSIDOPSIS BAHIA) AS INDICATORS OF STRESS FROM CHRONIC PESTICIDE EXPOSURE

EPA Science Inventory

Various aspects of the energy metabolism of an estuarine mysid (Mysidopsis bahia) were examined for different life stages during a life-cycle exposure to the organophosphate pesticide fenthion. Dose-response relationships were developed for several metabolic rate functions (oxyge...

A SHORT-TERM REPRODUCTIVE TEST WITH THE FATHEAD MINNOW (PIMEPHALES PROMELAS)

EPA Science Inventory

Due to the time and expense associated with full life-cycle testing, most current toxicity tests with fish do not explicity consider reproductive output as an endpoint but, rather, focus on early life-stage survival and development. However, there are classes of chemicals that co...

A SHORT-TERM REPRODUCTION TEST WITH THE FATHEAD MINNOW (PIMEPHALES PROMELAS): L METHODS DESCRIPTION

EPA Science Inventory

Due to the time and expense associated with full life-cycle testing, most current toxicity tests with fish do not explicity consider reproductive output as an endpoint but, rather, focus on early life-stage survival and development. However, there are classes of chemicals that co...

DEVELOPMENT-STAGE SPECIFIC LIFE-CYCLE BIOASSAY FOR ASSESSMENT OF SEDIMENT-ASSOCIATED TOXICANT EFFECTS ON BENTHIC COPEPOD PRODUCTION. (R825279)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

By land or by stream? contribution of constrained dispersal by adult caddisflies to diversity loss from urban headwaters

EPA Science Inventory

The adult stage of streams insects is responsible for important life-cycle processes such as dispersal and reproduction, yet interactions of adult stream insects with terrestrial landscapes are rarely studied. This trend is especially problematic in urbanized landscapes where th...

DEVELOPMENTAL STAGE-SPECIFIC LIFE-CYCLE BIOASSAY FOR ASSESSMENT OF SEDIMENT-ASSOCIATED TOXICANT EFFECTS ON BENTHIC COPEPOD PRODUCTION. (R827397)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

The Lifecycle of Trust in Educational Leadership: An Ecological Perspective

ERIC Educational Resources Information Center

Kutsyuruba, Benjamin; Walker, Keith

2015-01-01

As establishing and fostering trust are imperative activities for school leaders, cognizance of the fundamental importance of trust is essential for the leader's moral agency and ethical decision-making. In this article, we use an ecological perspective to uncover the dynamics of the lifecycle of trust as evident from extant literature on…

Software Program: Software Management Guidebook

NASA Technical Reports Server (NTRS)

1996-01-01

The purpose of this NASA Software Management Guidebook is twofold. First, this document defines the core products and activities required of NASA software projects. It defines life-cycle models and activity-related methods but acknowledges that no single life-cycle model is appropriate for all NASA software projects. It also acknowledges that the appropriate method for accomplishing a required activity depends on characteristics of the software project. Second, this guidebook provides specific guidance to software project managers and team leaders in selecting appropriate life cycles and methods to develop a tailored plan for a software engineering project.

The Activities of Current Antimalarial Drugs on the Life Cycle Stages of Plasmodium: A Comparative Study with Human and Rodent Parasites

PubMed Central

Delves, Michael; Plouffe, David; Scheurer, Christian; Meister, Stephan; Wittlin, Sergio; Winzeler, Elizabeth A.; Sinden, Robert E.; Leroy, Didier

2012-01-01

Background Malaria remains a disease of devastating global impact, killing more than 800,000 people every year—the vast majority being children under the age of 5. While effective therapies are available, if malaria is to be eradicated a broader range of small molecule therapeutics that are able to target the liver and the transmissible sexual stages are required. These new medicines are needed both to meet the challenge of malaria eradication and to circumvent resistance. Methods and Findings Little is known about the wider stage-specific activities of current antimalarials that were primarily designed to alleviate symptoms of malaria in the blood stage. To overcome this critical gap, we developed assays to measure activity of antimalarials against all life stages of malaria parasites, using a diverse set of human and nonhuman parasite species, including male gamete production (exflagellation) in Plasmodium falciparum, ookinete development in P. berghei, oocyst development in P. berghei and P. falciparum, and the liver stage of P. yoelii. We then compared 50 current and experimental antimalarials in these assays. We show that endoperoxides such as OZ439, a stable synthetic molecule currently in clinical phase IIa trials, are strong inhibitors of gametocyte maturation/gamete formation and impact sporogony; lumefantrine impairs development in the vector; and NPC-1161B, a new 8-aminoquinoline, inhibits sporogony. Conclusions These data enable objective comparisons of the strengths and weaknesses of each chemical class at targeting each stage of the lifecycle. Noting that the activities of many compounds lie within achievable blood concentrations, these results offer an invaluable guide to decisions regarding which drugs to combine in the next-generation of antimalarial drugs. This study might reveal the potential of life-cycle–wide analyses of drugs for other pathogens with complex life cycles. Please see later in the article for the Editors' Summary PMID:22363211

Design and life-cycle considerations for unconventional-reservoir wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miskimins, J.L.

2009-05-15

This paper provides an overview of design and life-cycle considerations for certain unconventional-reservoir wells. An overview of unconventional-reservoir definitions is provided. Well design and life-cycle considerations are addressed from three aspects: upfront reservoir development, initial well completion, and well-life and long-term considerations. Upfront-reservoir-development issues discussed include well spacing, well orientation, reservoir stress orientations, and tubular metallurgy. Initial-well-completion issues include maximum treatment pressures and rates, treatment diversion, treatment staging, flowback and cleanup, and dewatering needs. Well-life and long-term discussions include liquid loading, corrosion, refracturing and associated fracture reorientation, and the cost of abandonment. These design considerations are evaluated with case studiesmore » for five unconventional-reservoir types: shale gas (Barnett shale), tight gas (Jonah feld), tight oil (Bakken play), coalbed methane (CBM) (San Juan basin), and tight heavy oil (Lost Hills field). In evaluating the life cycle and design of unconventional-reservoir wells, 'one size' does not fit all and valuable knowledge and a shortening of the learning curve can be achieved for new developments by studying similar, more-mature fields.« less

HANFORD RIVER PROTECTION PROJECT ENHANCED MISSION PLANNING THROUGH INNOVATIVE TOOLS LIFECYCLE COST MODELING AND AQUEOUS THERMODYNAMIC MODELING - 12134

DOE Office of Scientific and Technical Information (OSTI.GOV)

PIERSON KL; MEINERT FL

2012-01-26

Two notable modeling efforts within the Hanford Tank Waste Operations Simulator (HTWOS) are currently underway to (1) increase the robustness of the underlying chemistry approximations through the development and implementation of an aqueous thermodynamic model, and (2) add enhanced planning capabilities to the HTWOS model through development and incorporation of the lifecycle cost model (LCM). Since even seemingly small changes in apparent waste composition or treatment parameters can result in large changes in quantities of high-level waste (HLW) and low-activity waste (LAW) glass, mission duration or lifecycle cost, a solubility model that more accurately depicts the phases and concentrations ofmore » constituents in tank waste is required. The LCM enables evaluation of the interactions of proposed changes on lifecycle mission costs, which is critical for decision makers.« less

When the seasons don't fit: speedy molt as a routine carry-over cost of reproduction.

PubMed

Dietz, Maurine W; Rogers, Ken G; Piersma, Theunis

2013-01-01

The failure of animals to fit all life-cycle stages into an annual cycle could reduce the chances of successful breeding. In some cases, non-optimal strategies will be adopted in order to maintain the life-cycle within the scope of one year. We studied trade-offs made by a High Arctic migrant shorebird, the red knot Calidris canutus islandica, between reproduction and wing feather molt carried out in the non-breeding period in the Dutch Wadden Sea. We compared primary molt duration between birds undertaking the full migratory and breeding schedule with birds that forego breeding because they are young or are maintained in captivity. Molt duration was ca. 71 days in breeding adults, which was achieved by an accelerated feather replacement strategy. Second-year birds and captive adults took ca. 22% and 27% longer, respectively. Second-year birds start molt in late June, more than four weeks before captive adults, and almost seven weeks before adults that return from breeding in late July-August. Adults finish molt in October when steeply increasing thermostatic costs and reductions in food availability occur. Primary molt duration was longer in female than in male knots (all ages), which was accordance with the somewhat larger body size of females. Since fast growth leads to lower quality feathers, the speedy wing molt shown by Arctic-breeding birds may represent a time constraint that is an unavoidable and routine cost of reproduction. So far it was hypothesized that only birds over 1 kg would have difficulty fitting molt within a year. Here we show that in birds an order of magnitude smaller, temporal imperatives may impose the adoption of non-optimal life-cycle routines in the entire actively breeding population.

Multifaceted Activity of Listeriolysin O, the Cholesterol-Dependent Cytolysin of Listeria monocytogenes

PubMed Central

2014-01-01

The cholesterol-dependent cytolysins (CDCs) are a large family of pore-forming toxins that are produced by numerous Gram-positive bacterial pathogens. These toxins are released in the extracellular environment as water-soluble monomers or dimers that bind to cholesterol-rich membranes and assemble into large pore complexes. Depending upon their concentration, the nature of the host cell and membrane (cytoplasmic or intracellular) they target, the CDCs can elicit many different cellular responses. Among the CDCs, listeriolysin O (LLO), which is a major virulence factor of the facultative intracellular pathogen Listeria monocytogenes, is involved in several stages of the intracellular lifecycle of the bacterium and displays unique characteristics. It has long been known that following L. monocytogenes internalization into host cells, LLO disrupts the internalization vacuole, enabling the bacterium to replicate into the host cell cytosol. LLO is then used by cytosolic bacteria to spread from cell to cell, avoiding bacterial exposure to the extracellular environment. Although LLO is continuously produced during the intracellular lifecycle of L. monocytogenes, several processes limit its toxicity to ensure the survival of infected cells. It was previously thought that LLO activity was limited to mediating vacuolar escape during bacterial entry and cell to cell spreading. This concept has been challenged by compelling evidence suggesting that LLO secreted by extracellular L. monocytogenes perforates the host cell plasma membrane, triggering important host cell responses. This chapter provides an overview of the well-established intracellular activity of LLO and the multiple roles attributed to LLO secreted by extracellular L. monocytogenes. PMID:24798012

The United States Geological Survey Science Data Lifecycle Model

USGS Publications Warehouse

Faundeen, John L.; Burley, Thomas E.; Carlino, Jennifer A.; Govoni, David L.; Henkel, Heather S.; Holl, Sally L.; Hutchison, Vivian B.; Martín, Elizabeth; Montgomery, Ellyn T.; Ladino, Cassandra; Tessler, Steven; Zolly, Lisa S.

2014-01-01

U.S. Geological Survey (USGS) data represent corporate assets with potential value beyond any immediate research use, and therefore need to be accounted for and properly managed throughout their lifecycle. Recognizing these motives, a USGS team developed a Science Data Lifecycle Model (SDLM) as a high-level view of data—from conception through preservation and sharing—to illustrate how data management activities relate to project workflows, and to assist with understanding the expectations of proper data management. In applying the Model to research activities, USGS scientists can ensure that data products will be well-described, preserved, accessible, and fit for re-use. The Model also serves as a structure to help the USGS evaluate and improve policies and practices for managing scientific data, and to identify areas in which new tools and standards are needed.

AN INTEGRATION OF COPEPOD-BASED BAFS, LIFECYCLE TOXICITY TESTING, AND ENDOCRINE DISRUPTION METHODOLOGIES FOR RAPID POPULATION-LEVEL RISK ASSESSMENT OF PERSISTENT BIOACCUMULATIVE TOXICANTS

EPA Science Inventory

Extensive multi-generational microplate culturing (copepod hatching stage through two broods) experiments were completed with the POPs lindane, DDD and fipronil sulfide.  Identical tandem microplate experiments were run concurrently to yield sufficient copepod biomass for li...

Ocean acidification affects redox-balance and ion-homeostasis in the life-cycle stages of Emiliania huxleyi.

PubMed

Rokitta, Sebastian D; John, Uwe; Rost, Björn

2012-01-01

Ocean Acidification (OA) has been shown to affect photosynthesis and calcification in the coccolithophore Emiliania huxleyi, a cosmopolitan calcifier that significantly contributes to the regulation of the biological carbon pumps. Its non-calcifying, haploid life-cycle stage was found to be relatively unaffected by OA with respect to biomass production. Deeper insights into physiological key processes and their dependence on environmental factors are lacking, but are required to understand and possibly estimate the dynamics of carbon cycling in present and future oceans. Therefore, calcifying diploid and non-calcifying haploid cells were acclimated to present and future CO(2) partial pressures (pCO(2); 38.5 Pa vs. 101.3 Pa CO(2)) under low and high light (50 vs. 300 µmol photons m(-2) s(-1)). Comparative microarray-based transcriptome profiling was used to screen for the underlying cellular processes and allowed to follow up interpretations derived from physiological data. In the diplont, the observed increases in biomass production under OA are likely caused by stimulated production of glycoconjugates and lipids. The observed lowered calcification under OA can be attributed to impaired signal-transduction and ion-transport. The haplont utilizes distinct genes and metabolic pathways, reflecting the stage-specific usage of certain portions of the genome. With respect to functionality and energy-dependence, however, the transcriptomic OA-responses resemble those of the diplont. In both life-cycle stages, OA affects the cellular redox-state as a master regulator and thereby causes a metabolic shift from oxidative towards reductive pathways, which involves a reconstellation of carbon flux networks within and across compartments. Whereas signal transduction and ion-homeostasis appear equally OA-sensitive under both light intensities, the effects on carbon metabolism and light physiology are clearly modulated by light availability. These interactive effects can be attributed to the influence of OA and light on the redox equilibria of NAD and NADP, which function as major sensors for energization and stress. This generic mode of action of OA may therefore provoke similar cell-physiological responses in other protists.

Transcriptome profiling of the dynamic life cycle of the scypohozoan jellyfish Aurelia aurita.

PubMed

Brekhman, Vera; Malik, Assaf; Haas, Brian; Sher, Noa; Lotan, Tamar

2015-02-14

The moon jellyfish Aurelia aurita is a widespread scyphozoan species that forms large seasonal blooms. Here we provide the first comprehensive view of the entire complex life of the Aurelia Red Sea strain by employing transcriptomic profiling of each stage from planula to mature medusa. A de novo transcriptome was assembled from Illumina RNA-Seq data generated from six stages throughout the Aurelia life cycle. Transcript expression profiling yielded clusters of annotated transcripts with functions related to each specific life-cycle stage. Free-swimming planulae were found highly enriched for functions related to cilia and microtubules, and the drastic morphogenetic process undergone by the planula while establishing the future body of the polyp may be mediated by specifically expressed Wnt ligands. Specific transcripts related to sensory functions were found in the strobila and the ephyra, whereas extracellular matrix functions were enriched in the medusa due to high expression of transcripts such as collagen, fibrillin and laminin, presumably involved in mesoglea development. The CL390-like gene, suggested to act as a strobilation hormone, was also highly expressed in the advanced strobila of the Red Sea species, and in the medusa stage we identified betaine-homocysteine methyltransferase, an enzyme that may play an important part in maintaining equilibrium of the medusa's bell. Finally, we identified the transcription factors participating in the Aurelia life-cycle and found that 70% of these 487 identified transcription factors were expressed in a developmental-stage-specific manner. This study provides the first scyphozoan transcriptome covering the entire developmental trajectory of the life cycle of Aurelia. It highlights the importance of numerous stage-specific transcription factors in driving morphological and functional changes throughout this complex metamorphosis, and is expected to be a valuable resource to the community.

Strong shift from HCO3 (-) to CO 2 uptake in Emiliania huxleyi with acidification: new approach unravels acclimation versus short-term pH effects.

PubMed

Kottmeier, Dorothee M; Rokitta, Sebastian D; Tortell, Philippe D; Rost, Björn

2014-09-01

Effects of ocean acidification on Emiliania huxleyi strain RCC 1216 (calcifying, diploid life-cycle stage) and RCC 1217 (non-calcifying, haploid life-cycle stage) were investigated by measuring growth, elemental composition, and production rates under different pCO2 levels (380 and 950 μatm). In these differently acclimated cells, the photosynthetic carbon source was assessed by a (14)C disequilibrium assay, conducted over a range of ecologically relevant pH values (7.9-8.7). In agreement with previous studies, we observed decreased calcification and stimulated biomass production in diploid cells under high pCO2, but no CO2-dependent changes in biomass production for haploid cells. In both life-cycle stages, the relative contributions of CO2 and HCO3 (-) uptake depended strongly on the assay pH. At pH values ≤ 8.1, cells preferentially used CO2 (≥ 90 % CO2), whereas at pH values ≥ 8.3, cells progressively increased the fraction of HCO3 (-) uptake (~45 % CO2 at pH 8.7 in diploid cells; ~55 % CO2 at pH 8.5 in haploid cells). In contrast to the short-term effect of the assay pH, the pCO2 acclimation history had no significant effect on the carbon uptake behavior. A numerical sensitivity study confirmed that the pH-modification in the (14)C disequilibrium method yields reliable results, provided that model parameters (e.g., pH, temperature) are kept within typical measurement uncertainties. Our results demonstrate a high plasticity of E. huxleyi to rapidly adjust carbon acquisition to the external carbon supply and/or pH, and provide an explanation for the paradoxical observation of high CO2 sensitivity despite the apparently high HCO3 (-) usage seen in previous studies.

Life-cycle GHG emissions of electricity from syngas produced by pyrolyzing woody biomass

Treesearch

Hongmei Gu; Richard Bergman

2015-01-01

Low-value residues from forest restoration activities in the western United States intended to mitigate effects from wildfire, climate change, and pests and disease need a sustainable market to improve the economic viability of treatment. Converting biomass into bioenergy is a potential solution. Life-cycle assessment (LCA) as a sustainable metric tool can assess the...

CRM1 Inhibitors for Antiviral Therapy

PubMed Central

Mathew, Cynthia; Ghildyal, Reena

2017-01-01

Infectious diseases are a major global concern and despite major advancements in medical research, still cause significant morbidity and mortality. Progress in antiviral therapy is particularly hindered by appearance of mutants capable of overcoming the effects of drugs targeting viral components. Alternatively, development of drugs targeting host proteins essential for completion of viral lifecycle holds potential as a viable strategy for antiviral therapy. Nucleocytoplasmic trafficking pathways in particular are involved in several pathological conditions including cancer and viral infections, where hijacking or alteration of function of key transporter proteins, such as Chromosome Region Maintenance1 (CRM1) is observed. Overexpression of CRM1-mediated nuclear export is evident in several solid and hematological malignancies. Interestingly, CRM1-mediated nuclear export of viral components is crucial in various stages of the viral lifecycle and assembly. This review summarizes the role of CRM1 in cancer and selected viruses. Leptomycin B (LMB) is the prototypical inhibitor of CRM1 potent against various cancer cell lines overexpressing CRM1 and in limiting viral infections at nanomolar concentrations in vitro. However, the irreversible shutdown of nuclear export results in high cytotoxicity and limited efficacy in vivo. This has prompted search for synthetic and natural CRM1 inhibitors that can potentially be developed as broadly active antivirals, some of which are summarized in this review. PMID:28702009

Rural Household Demographics, Livelihoods and the Environment

PubMed Central

de Sherbinin, Alex; VanWey, Leah; McSweeney, Kendra; Aggarwal, Rimjhim; Barbieri, Alisson; Henry, Sabina; Hunter, Lori M.; Twine, Wayne

2008-01-01

This paper reviews and synthesizes findings from scholarly work on linkages among rural household demographics, livelihoods and the environment. Using the livelihood approach as an organizing framework, we examine evidence on the multiple pathways linking environmental variables and the following demographic variables: fertility, migration, morbidity and mortality, and lifecycles. Although the review draws on studies from the entire developing world, we find the majority of micro-level studies have been conducted in either marginal (mountainous or arid) or frontier environments, especially Amazonia. Though the linkages are mediated by many complex and often context-specific factors, there is strong evidence that dependence on natural resources intensifies when households lose human and social capital through adult morbidity and mortality, and qualified evidence for the influence of environmental factors on household decision-making regarding fertility and migration. Two decades of research on lifecycles and land-cover change at the farm level have yielded a number of insights about how households make use of different land-use and natural resource management strategies at different stages. A thread running throughout the review is the importance of managing risk through livelihood diversification, ensuring future income security, and culture-specific norms regarding appropriate and desirable activities and demographic responses. Recommendations for future research are provided. PMID:19190718

Trematode diversity in freshwater fishes of the Globe I: 'Old World'.

PubMed

Scholz, Tomáš; Besprozvannykh, Vladimir V; Boutorina, Tamara E; Choudhury, Anindo; Cribb, Thomas H; Ermolenko, Alexey V; Faltýnková, Anna; Shedko, Marina B; Shimazu, Takeshi; Smit, Nico J

2016-03-01

In this paper, we review, continent by continent, the trematode fauna of freshwater fishes of the 'Old World', a vast area consisting of the Palaearctic, Ethiopian, Oriental and Australasian zoogeographical regions. Knowledge of this fauna is highly uneven and clearly incomplete for almost all regions, sometimes dramatically so. Although the biggest problem remains the completion of the 'first pass' of alpha taxonomy, there are in addition great problems relating to biogeography and elucidation of life-cycles. For the latter, molecular data, i.e. matching DNA sequences of larval stages and corresponding adults, may represent a powerful tool that should be used in future studies. Another challenging problem represents the existence of cryptic species and, in particular, considerable decrease of experts in taxonomy and life-cycles of trematodes.

Systems Engineering Model for ART Energy Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendez Cruz, Carmen Margarita; Rochau, Gary E.; Wilson, Mollye C.

The near-term objective of the EC team is to establish an operating, commercially scalable Recompression Closed Brayton Cycle (RCBC) to be constructed for the NE - STEP demonstration system (demo) with the lowest risk possible. A systems engineering approach is recommended to ensure adequate requirements gathering, documentation, and mode ling that supports technology development relevant to advanced reactors while supporting crosscut interests in potential applications. A holistic systems engineering model was designed for the ART Energy Conversion program by leveraging Concurrent Engineering, Balance Model, Simplified V Model, and Project Management principles. The resulting model supports the identification and validation ofmore » lifecycle Brayton systems requirements, and allows designers to detail system-specific components relevant to the current stage in the lifecycle, while maintaining a holistic view of all system elements.« less

Effect of tanniniferous food from Bauhinia pulchella on pasture contamination with gastrointestinal nematodes from goats.

PubMed

Lopes, Suzana G; Barros, Lilyan B G; Louvandini, Helder; Abdalla, Adibe L; Costa Junior, Livio M

2016-02-24

Tannin-rich plants have been examined as an alternative for controlling the gastrointestinal nematodes in ruminants. In vivo assays typically examine the anthelmintic activity in female fecundity and/or the adult worm burden, without considering other life-cycle stages or the impact on pasture contamination. The aim of the present study was to evaluate the anthelmintic activity of tanniniferous food from Bauhinia pulchella in goats and the potential impact on pasture contamination with the infective larval stage of gastrointestinal nematodes. Sixteen cross breed Boer goats that were naturally infected with gastrointestinal nematodes were fed tanniniferous concentrate from the leaves of B. pulchella and compared to a separate paddock of control animals without condensed tannin supplementation. A range of parasite characteristics were monitored throughout the 63 days of experimentation, including faecal egg count (FEC), egg hatching and relative numbers of hatched helminth larvae on herbage. Worm free tracer animals were used to assess the infective larval stage load of the contaminated pasture. The tanniniferous food did not reduce the combined FEC values, but egg hatching was significantly affected (p < 0.05). The pasture grazed by goats fed with tanniniferous food from B. pulchella showed reduced contamination through infective larval stages. Tracer goats maintained in paddocks grazed with animals fed with tanniniferous food had lower numbers of Trichostrongylus colubriformis than did those in the control group (86 % reduction). Condensed tannin from B. pulchella showed anthelmintic activity, affected egg viability and reduced pasture contamination, which led to the reduced infection of the animals by T. colubriformis.

Evaluation of four bed bug traps for surveillances of brown dog ticks (Acari: Ixodidae)

USDA-ARS?s Scientific Manuscript database

The brown dog tick can be a serious residential pest due to its unique ability, among ticks, to complete its lifecycle indoors. A single engorged and fertilized female tick can oviposit around 4,000 eggs, allowing indoor establishment to be rapid and easy to miss in early-stage infestations. Acari...

Ontology for Life-Cycle Modeling of Electrical Distribution Systems: Model View Definition

DTIC Science & Technology

2013-06-01

building information models ( BIM ) at the coordinated design stage of building construction. 1.3 Approach To...standard for exchanging Building Information Modeling ( BIM ) data, which defines hundreds of classes for common use in software, currently supported by...specifications, Construction Operations Building in- formation exchange (COBie), Building Information Modeling ( BIM ) 16. SECURITY CLASSIFICATION OF:

The Surface Layer Mechanical Condition and Residual Stress Forming Model in Surface Plastic Deformation Process with the Hardened Body Effect Consideration

NASA Astrophysics Data System (ADS)

Mahalov, M. S.; Blumenstein, V. Yu

2017-10-01

The mechanical condition and residual stresses (RS) research and computational algorithms creation in complex types of loading on the product lifecycle stages relevance is shown. The mechanical state and RS forming finite element model at surface plastic deformation strengthening machining, including technological inheritance effect, is presented. A model feature is the production previous stages obtained transformation properties consideration, as well as these properties evolution during metal particles displacement through the deformation space in the present loading step.

What's in a Number: How we Measure Community Engagement

NASA Astrophysics Data System (ADS)

Budden, A. E.; Aicher, R.; Butland, S.; Varga, M.

2017-12-01

The importance of community management is increasingly recognized and the role of the community manager is becoming professionalized. Yet, activities involved in community management - or community engagement - are widespread, and have typically been taken on by a variety of actors. These activities will look different depending on the type of community an individual is working with, and the maturity of the community. Regardless of the myriad of tools and practices used in community management, most community managers are seeking growth and a transition to a mature and self-sustaining community. Measuring this growth and degree of engagement can be challenging. Harder still is inferring the impact of community growth. In this paper we discuss some of the most commonly used metrics for community engagement, their advantages and limitations, and their context dependency, drawing from case studies of communities at different stages of the community life-cycle.

TRANSCRIPTIONAL INHIBITION OF INTERLEUKIN-12 PROMOTER ACTIVITY IN LEISHMANIA SPP.-INFECTED MACROPHAGES

PubMed Central

Jayakumar, Asha; Widenmaier, Robyn; Ma, Xiaojing; McDowell, Mary Ann

2009-01-01

To establish and persist within a host, Leishmania spp. parasites delay the onset of cell-mediated immunity by suppressing interleukin-12 (IL-12) production from host macrophages. Although it is established that Leishmania spp.-infected macrophages have impaired IL-12 production, the mechanisms that account for this suppression remain to be completely elucidated. Using a luciferase reporter assay assessing IL-12 transcription, we report here that Leishmania major, Leishmania donovani, and Leishmania chagasi inhibit IL-12 transcription in response to interferon-gamma, lipopolysaccharide, and CD40 ligand and that Leishmania spp. lipophosphoglycan, phosphoglycans, and major surface protein are not necessary for inhibition. In addition, all the Leishmania spp. strains and life-cycle stages tested inhibited IL-12 promoter activity. Our data further reveal that autocrine-acting host factors play no role in the inhibitory response and that phagocytosis signaling is necessary for inhibition of IL-12. PMID:18372625

Malaria invasion ligand RH5 and its prime candidacy in blood-stage malaria vaccine design

PubMed Central

Ord, Rosalynn L; Rodriguez, Marilis; Lobo, Cheryl A

2015-01-01

With drug resistance to available therapeutics continuing to develop against Plasmodium falciparum malaria, the development of an effective vaccine candidate remains a major research goal. Successful interruption of invasion of parasites into erythrocytes during the blood stage of infection will prevent the severe clinical symptoms and complications associated with malaria. Previously studied blood stage antigens have highlighted the hurdles that are inherent to this life-cycle stage, namely that highly immunogenic antigens are also globally diverse, resulting in protection only against the vaccine strain, or that naturally acquired immunity to blood stage antigens do not always correlate with actual protection. The blood stage antigen reticulocyte binding homolog RH5 is essential for parasite viability, has globally limited diversity, and is associated with protection from disease. Here we summarize available information on this invasion ligand and recent findings that highlight its candidacy for inclusion in a blood-stage malaria vaccine. PMID:25844685

Assurance specification documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 4

NASA Technical Reports Server (NTRS)

Callender, E. David; Steinbacher, Jody

1989-01-01

This is the fourth of five volumes on Information System Life-Cycle and Documentation Standards. This volume provides a well organized, easily used standard for assurance documentation for information systems and software, hardware, and operational procedures components, and related processes. The specifications are developed in conjunction with the corresponding management plans specifying the assurance activities to be performed.

Toward a Formal Model of the Design and Evolution of Software

DTIC Science & Technology

1988-12-20

should have the flezibiity to support a variety of design methodologies, be compinhenaive enough to encompass the gamut of software lifecycle...the future. It should have the flezibility to support a variety of design methodologies, be comprehensive enough to encompass the gamut of software...variety of design methodologies, be comprehensive enough to encompass the gamut of software lifecycle activities, and be precise enough to provide the

Female reproductive impacts of dietary methylmercury in yellow perch (Perca flavescens) and zebrafish (Danio rerio).

PubMed

DeBofsky, Abigail R; Klingler, Rebekah H; Mora-Zamorano, Francisco X; Walz, Marcus; Shepherd, Brian; Larson, Jeremy K; Anderson, David; Yang, Luobin; Goetz, Frederick; Basu, Niladri; Head, Jessica; Tonellato, Peter; Armstrong, Brandon M; Murphy, Cheryl; Carvan, Michael J

2018-03-01

The purpose of this study was to evaluate the effects of environmentally relevant dietary MeHg exposures on adult female yellow perch (Perca flavescens) and female zebrafish (Danio rerio) ovarian development and reproduction. Yellow perch were used in the study for their socioeconomic and ecological importance within the Great Lakes basin, and the use of zebrafish allowed for a detailed analysis of the molecular effects of MeHg following a whole life-cycle exposure. Chronic whole life dietary exposure of F 1 zebrafish to MeHg mimics realistic wildlife exposure scenarios, and the twenty-week adult yellow perch exposure (where whole life-cycle exposures are difficult) captures early seasonal ovarian development. For both species, target dietary accumulation values were achieved prior to analyses. In zebrafish, several genes involved in reproductive processes were shown to be dysregulated by RNA-sequencing and quantitative real-time polymerase chain reaction (QPCR), but no significant phenotypic changes were observed regarding ovarian staging, fecundity, or embryo mortality. Yellow perch were exposed to dietary MeHg for 12, 16, or 20 weeks. In this species, a set of eight genes were assessed by QPCR in the pituitary, liver, and ovary, and no exposure-related changes were observed. The lack of genomic resources in yellow perch hinders the characterization of subtle molecular impacts. The ovarian somatic index, circulating estradiol and testosterone, and ovarian staging were not significantly altered by MeHg exposure in yellow perch. These results suggest that environmentally relevant MeHg exposures do not drastically reduce the reproductively important endpoints in these fish, but to capture realistic exposure scenarios, whole life-cycle yellow perch exposures are needed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental impact assessment and eco-friendly decision-making in civil structures.

PubMed

Kim, Sang-Hyo; Choi, Moon-Seock; Mha, Ho-Seong; Joung, Jung-Yeun

2013-09-15

This study develops two useful procedures in performing an environmental-impact assessment. One is the advanced life-cycle assessment (LCA) method, which effectively tracks the flow of materials and considers the recycling and demolition of a civil structure. The other is an eco-friendly decision-making procedure, which may effectively apply when determining the prototype of a civil structure. The advanced LCA method differs from traditional LCA procedure, as it classifies the input material prior to the impact assessment. Classification work is performed to establish independent life-cycle stages for each material. The processes of recycling and demolition are appropriately added to the life-cycle stages. The impact assessment is performed separately for the materials, and results are aggregated at the end of the analysis. The eco-friendly decision-making procedure enables designers to choose an economical, and environmentally friendly, alternative during the planning phase of the construction project. This procedure rationally amalgamates economical value and environmental effects into a single indicator. The life cycle cost (LCC) of a structure can be analysed by using conventional LCC tools, whereas the environmental impact is estimated by LCA. The results from LCC and LCA are then integrated by using either a CO2 conversion method or an analytical hierarchy process (AHP). The CO2 conversion method presents the result as a monetary value, whereas the AHP presents the result as a non-dimensional value. A practical example using a steel box girder bridge and a pre-stressed concrete (PSC) box-girder bridge is also given in order to aid the understanding of the presented procedure. Copyright © 2013 Elsevier Ltd. All rights reserved.

Seasonal lipid dynamics of Calanus finmarchicus and C. helgolandicus in the Norwegian Sea: The role of energy for "decision making" in life-cycle events

NASA Astrophysics Data System (ADS)

Melle, W.; Broms, C.; Meier, S.; Mæhle, S.; Skern, R.

2016-02-01

Accumulation and utilization of stored lipids impact important life-cycle events of Calanus species. The con-generic copepods Calanus finmarchicus (cold-temperate) and C. helgolandicus (warm-temperate) co-occur in the Norwegian Sea, although their abundances and seasonal dynamics differ. These species also exhibit important differences regarding behaviour, fat metabolism and deposition, and diet. During one year, C. finmarchicus and C. helgolandicus were sampled at a number of stations in the Norwegian Sea in January, May and November. The samples are depth-stratified, taken down to 1500 meters depth, and have been analyzed to copepodite stages IV, V and VI males and females. The species are separated based on genetic analysis. The lipid classes (phospholipids, triacylglycerol and wax esters) composition of the different species are analysed by Folch extraction and Thin-Layer Chromatography (TLC) followed by gas chromatography analysis of fatty acids and alcohols. The species-, stage-, and depth specific lipid contents have been related to the Calanus species vertical distribution, physical environment, prey field, and invertebrate predator field. Questions that have been attempted answered: How does the lipid content affect vertical seasonal migration? How does the lipid content affect overwintering depth and duration of diapause? Can lipid content explain differences in behaviour and phenology between C. finmarchicus and C. helgolandicus? Preliminary analyses of fatty acids reveals only small differences in the diet composition of C. finmarchicus and C. helgolandicus sampled at the same location. The Calanus species are adapted to different habitats and temperature regimes. Improving our understanding of how diet and fat accumulation and utilization affects important life-cycle events will allow us to better predict how these species, and thus the herbivore community of the Norwegian Sea, will change in response to global warming.

Transition to Early Childhood Education: Parents' Use of Coping Strategies in Dealing with Children's Adjustment Difficulties in Hong Kong

ERIC Educational Resources Information Center

Lam, Mei Seung

2014-01-01

The transition from home to early childhood education can be stressful for both children and parents. How parents cope with this potentially stressful event affects both the children's adaptation and the parents' lives during the preschooler stage of the family lifecycle. This paper examines how parents respond to their children's adjustment…

Cystic pulmonary hydatidosis

PubMed Central

Sarkar, Malay; Pathania, Rajnish; Jhobta, Anupam; Thakur, Babu Ram; Chopra, Rajesh

2016-01-01

Cystic echinococcosis (CE) is a zoonotic parasitic disease caused by the larval stages of the cestode Echinococcus granulosus. Worldwide, pulmonary hydatid cyst is a significant problem medically, socially, and economically. Surgery is the definitive therapy of pulmonary hydatidosis. Benzimidazoles may be considered in patients with a surgical contraindication. This review will focus on pathogenesis, lifecycle, clinical features, and management of pulmonary hydatid disease. PMID:27051107

Evaluating the fate of mercury and other metals across the life-cycle stages from the use of FGD gypsum for wallboard production

EPA Science Inventory

In 2007, 12.3 million tons of flue gas desulfurization (FGD) gypsum was produced due to air emission controls at coal-fired power plants. With increasing use of wet scrubbers in response to more stringent air pollution control requirements, FGD gypsum production is expected to in...

Life Events, Public Policy and the Economic Vulnerability of Children and the Elderly.

ERIC Educational Resources Information Center

Burkhauser, Richard V.; Duncan, Greg J.

This report uses longitudinal data to provide a dynamic picture of the family income experiences of children and the elderly. In contrast to the image of fairly stable incomes during most life-cycle stages, findings show substantial income volatility at all points in the life span, placing substantial numbers of the population at risk of suffering…

Affordable In-Space Transportation

NASA Technical Reports Server (NTRS)

Curtis, L. A.; VanDyke, M. K.; Lajoie, R. M.; Woodcock, G. R.

1996-01-01

Current and proposed launch systems will provide access to low-Earth orbit (LEO), and destinations beyond LEO, but the cost of delivering payloads will preclude the use of these services by many users. To develop and encourage revolutionary commercial utilization of geosynchronous orbit (GEO) and to provide an affordable means to continue NASA space science and exploration missions, the transportation costs to in-space destinations must be reduced. The principal objective of this study was to conceptually define three to four promising approaches to in-space transportation for delivery of satellites and other payloads, 3,000- to 10,000-lb class, to GEO destinations. This study established a methodology for evaluating in-space transportation systems based on life-cycle cost. The reusable concepts seemed to fare better in the evaluation than expendable, since a major driver in the life-cycle cost was the stage production cost.

Plasmodium falciparum SERA5 plays a non-enzymatic role in the malarial asexual blood-stage lifecycle

PubMed Central

Stallmach, Robert; Kavishwar, Manoli; Withers-Martinez, Chrislaine; Hackett, Fiona; Collins, Christine R; Howell, Steven A; Yeoh, Sharon; Knuepfer, Ellen; Atid, Avshalom J; Holder, Anthony A; Blackman, Michael J

2015-01-01

The malaria parasite Plasmodium falciparum replicates in an intraerythrocytic parasitophorous vacuole (PV). The most abundant P. falciparum PV protein, called SERA5, is essential in blood stages and possesses a papain-like domain, prompting speculation that it functions as a proteolytic enzyme. Unusually however, SERA5 possesses a Ser residue (Ser596) at the position of the canonical catalytic Cys of papain-like proteases, and the function of SERA5 or whether it performs an enzymatic role is unknown. In this study, we failed to detect proteolytic activity associated with the Ser596-containing parasite-derived or recombinant protein. However, substitution of Ser596 with a Cys residue produced an active recombinant enzyme with characteristics of a cysteine protease, demonstrating that SERA5 can bind peptides. Using targeted homologous recombination in P. falciparum, we substituted Ser596 with Ala with no phenotypic consequences, proving that SERA5 does not perform an essential enzymatic role in the parasite. We could also replace an internal segment of SERA5 with an affinity-purification tag. In contrast, using almost identical targeting constructs, we could not truncate or C-terminally tag the SERA5 gene, or replace Ser596 with a bulky Arg residue. Our findings show that SERA5 plays an indispensable but non-enzymatic role in the P. falciparum blood-stage life cycle. PMID:25599609

Whole parasite blood stage malaria vaccines: a convergence of evidence.

PubMed

McCarthy, James S; Good, Michael F

2010-01-01

There is a growing realization of the limitations of recombinant protein-based malaria vaccines. This, coupled with a better understanding of the protective immunity to malaria, both in animal models and in naturally exposed human populations and experimentally infected volunteers, as well as the increased capacity to manipulate parasites provides new impetus to evaluate whole blood stage parasite approaches to malaria vaccine development. In this review previous studies in rodents and primates of whole killed and attenuated blood stage vaccines, and recent work on the effect of genetically attenuated parasites on immunity in rodent models of blood stage immunity are discussed. The relationship between these findings and what is now known about protective immunity in human populations, specifically against the blood stages of the parasite lifecycle is discussed and recent findings from human experimental infection are be reviewed. Finally, the prospect for and impediments to the development whole blood stage parasites are reviewed.

Awareness about taeniasis and neurocysticercosis among municipal schoolteachers in Delhi.

PubMed

Mishra, D; Kalra, V; Aggarwal, K

2007-12-01

Taenia solium is the commonest parasitic infection of CNS and an important cause of new-onset seizures and epilepsy in children and adults. Human activities impact on almost every one of the stages of the lifecycle of the worm as man is responsible for dispersion of the parasite's egg through outdoor defecation and indiscriminate disposal of feces. Health education to cause behavioral changes in these practices can therefore be an effective intervention strategy. We conducted a study to assess KAP regarding taeniasis and neurocysticercosis among municipal school teachers in Delhi. The findings are presented in this communication. The study revealed that, general information related to personal food hygiene was known to majority of the teachers but core information in the context of taeniasis/cysticercosis and seizure prevention was lacking.

Behavioral aspects of development of eating behavior and nutrition status.

PubMed

Vazir, Shahnaz

2002-05-01

Studies on the development of eating behavior in rural India indicated that mothers of young children made food choices that fit into their budgets, and were also influenced by new information. Their choices were still immersed in traditional beliefs, some of which had positive effects on nutrition. Specific childrearing behaviors influenced positive deviance in the growth and psychosocial development of infants and preschoolers. A life-cycle approach to the development of eating behavior that deciphers needs at each stage and linkages between stages is necessary. Cost-benefit needs to be considered when devising strategies for future intervention programs.

Ontogenetic changes in helminth membrane function.

PubMed

Arme, C

1988-01-01

During their life-cycle many parasites experience a wide range of environments including free living and those provided by a variety of intermediate and final hosts. The nutritional requirements of parasites are met by physiological processes adapted to exploit the physicochemical characteristics provided by different hosts. In helminth parasites these adaptations are frequently expressed on the tegumentary surface. As an example of adaptations within the Trematoda, the control of monosaccharide transport in Proterometra sp. is described. Environmental sodium, although not directly involved in the uptake process, nevertheless regulates the expression of transport capabilities. In the Cestoda, the uptake of monosaccharides and amino acids is described for Hymenolepis diminuta. The metacestode of this tapeworm inhabits the blood system of an arthropod, and the adult the gut of a mammal. There are quantitative and qualitative differences in the amino acids and monosaccharides in these two environments and these are reflected in the transport mechanisms exhibited by the two forms of the life-cycle. In Echinococcus granulosus the transfer of amino acids, sugars and macromolecules across the membranes of hydatid cysts and protoscoleces is described. The major difference between these two stages in the life-cycle relates to the ability of hydatid cysts to absorb macromolecules, whereas protoscoleces are impermeable to these compounds. The potential for future work is emphasized.

Environmental assessment of biofuel pathways in Ile de France based on ecosystem modeling.

PubMed

Gabrielle, Benoît; Gagnaire, Nathalie; Massad, Raia Silvia; Dufossé, Karine; Bessou, Cécile

2014-01-01

The objective of the work reported here was to reduce the uncertainty on the greenhouse gas balances of biofuels using agro-ecosystem modeling at a high resolution over the Ile-de-France region in Northern France. The emissions simulated during the feedstock production stage were input to a life-cycle assessment of candidate biofuel pathways: bioethanol from wheat, sugar-beet and miscanthus, and biodiesel from oilseed rape. Compared to the widely-used methodology based on fixed emission factors, ecosystem modeling lead to 55-70% lower estimates for N2O emissions, emphasizing the importance of regional factors. The life-cycle GHG emissions of first-generation biofuels were 50-70% lower than fossil-based equivalents, and 85% lower for cellulosic ethanol. When including indirect land-use change effects, GHG savings became marginal for biodiesel and wheat ethanol, but were positive due to direct effects for cellulosic ethanol. Copyright © 2013 Elsevier Ltd. All rights reserved.

Process change evaluation framework for allogeneic cell therapies: impact on drug development and commercialization.

PubMed

Hassan, Sally; Huang, Hsini; Warren, Kim; Mahdavi, Behzad; Smith, David; Jong, Simcha; Farid, Suzanne S

2016-04-01

Some allogeneic cell therapies requiring a high dose of cells for large indication groups demand a change in cell expansion technology, from planar units to microcarriers in single-use bioreactors for the market phase. The aim was to model the optimal timing for making this change. A development lifecycle cash flow framework was created to examine the implications of process changes to microcarrier cultures at different stages of a cell therapy's lifecycle. The analysis performed under assumptions used in the framework predicted that making this switch earlier in development is optimal from a total expected out-of-pocket cost perspective. From a risk-adjusted net present value view, switching at Phase I is economically competitive but a post-approval switch can offer the highest risk-adjusted net present value as the cost of switching is offset by initial market penetration with planar technologies. The framework can facilitate early decision-making during process development.

Integration and validation testing for PhEDEx, DBS and DAS with the PhEDEx LifeCycle agent

NASA Astrophysics Data System (ADS)

Boeser, C.; Chwalek, T.; Giffels, M.; Kuznetsov, V.; Wildish, T.

2014-06-01

The ever-increasing amount of data handled by the CMS dataflow and workflow management tools poses new challenges for cross-validation among different systems within CMS experiment at LHC. To approach this problem we developed an integration test suite based on the LifeCycle agent, a tool originally conceived for stress-testing new releases of PhEDEx, the CMS data-placement tool. The LifeCycle agent provides a framework for customising the test workflow in arbitrary ways, and can scale to levels of activity well beyond those seen in normal running. This means we can run realistic performance tests at scales not likely to be seen by the experiment for some years, or with custom topologies to examine particular situations that may cause concern some time in the future. The LifeCycle agent has recently been enhanced to become a general purpose integration and validation testing tool for major CMS services. It allows cross-system integration tests of all three components to be performed in controlled environments, without interfering with production services. In this paper we discuss the design and implementation of the LifeCycle agent. We describe how it is used for small-scale debugging and validation tests, and how we extend that to large-scale tests of whole groups of sub-systems. We show how the LifeCycle agent can emulate the action of operators, physicists, or software agents external to the system under test, and how it can be scaled to large and complex systems.

Recent advances in recombinant protein-based malaria vaccines.

PubMed

Draper, Simon J; Angov, Evelina; Horii, Toshihiro; Miller, Louis H; Srinivasan, Prakash; Theisen, Michael; Biswas, Sumi

2015-12-22

Plasmodium parasites are the causative agent of human malaria, and the development of a highly effective vaccine against infection, disease and transmission remains a key priority. It is widely established that multiple stages of the parasite's complex lifecycle within the human host and mosquito vector are susceptible to vaccine-induced antibodies. The mainstay approach to antibody induction by subunit vaccination has been the delivery of protein antigen formulated in adjuvant. Extensive efforts have been made in this endeavor with respect to malaria vaccine development, especially with regard to target antigen discovery, protein expression platforms, adjuvant testing, and development of soluble and virus-like particle (VLP) delivery platforms. The breadth of approaches to protein-based vaccines is continuing to expand as innovative new concepts in next-generation subunit design are explored, with the prospects for the development of a highly effective multi-component/multi-stage/multi-antigen formulation seeming ever more likely. This review will focus on recent progress in protein vaccine design, development and/or clinical testing for a number of leading malaria antigens from the sporozoite-, merozoite- and sexual-stages of the parasite's lifecycle-including PfCelTOS, PfMSP1, PfAMA1, PfRH5, PfSERA5, PfGLURP, PfMSP3, Pfs48/45 and Pfs25. Future prospects and challenges for the development, production, human delivery and assessment of protein-based malaria vaccines are discussed. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Parasites as prey in aquatic food webs: implications for predator infection and parasite transmission

USGS Publications Warehouse

Thieltges, David W.; Amundsen, Per-Arne; Hechinger, Ryan F.; Johnson, Pieter T.J.; Lafferty, Levin D.; Mouritsen, Kim N.; Preston, Daniel L.; Reise, Karsten; Zander, C. Dieter; Poulin, Robert

2013-01-01

While the recent inclusion of parasites into food-web studies has highlighted the role of parasites as consumers, there is accumulating evidence that parasites can also serve as prey for predators. Here we investigated empirical patterns of predation on parasites and their relationships with parasite transmission in eight topological food webs representing marine and freshwater ecosystems. Within each food web, we examined links in the typical predator–prey sub web as well as the predator–parasite sub web, i.e. the quadrant of the food web indicating which predators eat parasites. Most predator– parasite links represented ‘concomitant predation’ (consumption and death of a parasite along with the prey/host; 58–72%), followed by ‘trophic transmission’ (predator feeds on infected prey and becomes infected; 8–32%) and predation on free-living parasite life-cycle stages (4–30%). Parasite life-cycle stages had, on average, between 4.2 and 14.2 predators. Among the food webs, as predator richness increased, the number of links exploited by trophically transmitted parasites increased at about the same rate as did the number of links where these stages serve as prey. On the whole, our analyses suggest that predation on parasites has important consequences for both predators and parasites, and food web structure. Because our analysis is solely based on topological webs, determining the strength of these interactions is a promising avenue for future research.

5 CFR 1601.40 - Lifecycle Funds.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 5 Administrative Personnel 3 2011-01-01 2011-01-01 false Lifecycle Funds. 1601.40 Section 1601.40 Administrative Personnel FEDERAL RETIREMENT THRIFT INVESTMENT BOARD PARTICIPANTS' CHOICES OF TSP FUNDS Lifecycle Funds § 1601.40 Lifecycle Funds. The Executive Director will establish TSP Lifecycle Funds, which are...

5 CFR 1601.40 - Lifecycle Funds.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Lifecycle Funds. 1601.40 Section 1601.40 Administrative Personnel FEDERAL RETIREMENT THRIFT INVESTMENT BOARD PARTICIPANTS' CHOICES OF TSP FUNDS Lifecycle Funds § 1601.40 Lifecycle Funds. The Executive Director will establish TSP Lifecycle Funds, which are...

TWRS configuration management requirement source document

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vann, J.M.

The TWRS Configuration Management (CM) Requirement Source document prescribes CM as a basic product life-cycle function by which work and activities are conducted or accomplished. This document serves as the requirements basis for the TWRS CM program. The objective of the TWRS CM program is to establish consistency among requirements, physical/functional configuration, information, and documentation for TWRS and TWRS products, and to maintain this consistency throughout the life-cycle of TWRS and the product, particularly as changes are being made.

Multi-host model-based identification of Armillifer agkistrodontis (Pentastomida), a new zoonotic parasite from China.

PubMed

Chen, Shao-Hong; Liu, Qin; Zhang, Yong-Nian; Chen, Jia-Xu; Li, Hao; Chen, Ying; Steinmann, Peter; Zhou, Xiao-Nong

2010-04-06

Pentastomiasis is a rare parasitic infection of humans. Pentastomids are dioecious obligate parasites requiring multiple hosts to complete their lifecycle. Despite their worm-like appearance, they are commonly placed into a separate sub-class of the subphylum Crustacea, phylum Arthropoda. However, their systematic position is not uncontested and historically, they have been considered as a separate phylum. An appraisal of Armillifer agkistrodontis was performed in terms of morphology and genetic identification after its lifecycle had been established in a multi-host model, i.e., mice and rats as intermediate hosts, and snakes (Agkistrodon acutus and Python molurus) as definitive hosts. Different stages of the parasite, including eggs, larvae and adults, were isolated and examined morphologically using light and electron microscopes. Phylogenetic and cluster analysis were also undertaken, focusing on the 18S rRNA and the Cox1 gene. The time for lifecycle completion was about 14 months, including 4 months for the development of eggs to infectious larvae in the intermediate host and 10 months for infectious larvae to mature in the final host. The main morphological difference between A. armillatus and Linguatula serrata is the number of abdominal annuli. Based on the 18S rRNA sequence, the shortest hereditary distance was found between A. agkistrodontis and Raillietiella spp. The highest degree of homology in the Cox 1 nucleic acid sequences and predicted amino acid sequences was found between A. agkistrodontis and A. armillatus. This is the first time that a multi-host model of the entire lifecycle of A. agkistrodontis has been established. Morphologic and genetic analyses supported the notion that pentastomids should be placed into the phylum Arthropoda.

Life-Cycle Costs of Alternative ICBM Second Stage Designs

DTIC Science & Technology

1992-09-01

of Logistics, Air Force Institute of Technology (AU), Wright-Patterson AFB OH, 1992. 34. Horngren , Charles T. and George Foster. Cost Accounting ; A...Managerial Emphasis (Sixth Edition). Englewood Cliffs NJ: Prentice-Hall, Inc., 1987. 35. Horngren , Charles T. and George Foster. Cost Accounting ; A...our research. We would also like to thank those involved with the 1991 Small ICBM Operations and Support cost estimate. Your assistance with the O& S

Increased importance of the documented development stage in process validation.

PubMed

Mohammed-Ziegler, Ildikó; Medgyesi, Ildikó

2012-07-01

Current trends in pharmaceutical quality assurance moved when the Federal Drug Administration (FDA) of the USA published its new guideline on process validation in 2011. This guidance introduced the lifecycle approach of process validation. In this short communication some typical changes from the point of view of practice of API production are addressed in the light of inspection experiences. Some details are compared with the European regulations.

The Morningside Initiative: Collaborative Development of a Knowledge Repository to Accelerate Adoption of Clinical Decision Support

DTIC Science & Technology

2010-01-01

Comparative Effectiveness Research, or other efforts to determine best practices and to develop guidelines based on meta-analysis and evidence - based medicine . An...authoritative reviews or other evidence - based medicine sources, but they have been made unambiguous and computable – a process which sounds...best practice recommendation created through an evidence - based medicine (EBM) development process. The lifecycle envisions four stages of refinement

How warm is too warm for the life cycle of actinopterygian fishes?

PubMed Central

Motani, Ryosuke; Wainwright, Peter C.

2015-01-01

We investigated the highest constant temperature at which actinopterygian fishes can complete their lifecycles, based on an oxygen supply model for cleavage-stage eggs. This stage is one of the most heat-sensitive periods during the lifecycle, likely reflecting the exhaustion of maternally supplied heat shock proteins without new production. The model suggests that average eggs would not develop normally under a constant temperature of about 36 °C or higher. This estimate matches published empirical values derived from laboratory and field observations. Spermatogenesis is more heat sensitive than embryogenesis in fishes, so the threshold may indeed be lower, at about 35 °C, unless actinopterygian fishes evolve heat tolerance during spermatogenesis as in birds. Our model also predicts an inverse relationship between egg size and temperature, and empirical data support this prediction. Therefore, the average egg size, and hence hatching size, is expected to shrink in a greenhouse world but a feeding function prohibits the survival of very small hatchlings, posing a limit to the shrinkage. It was once suggested that a marine animal community may be sustained under temperatures up to about 38 °C, and this value is being used, for example, in paleotemperature reconstruction. A revision of the value is overdue. (199/200) PMID:26166622

Impact of hot events at different developmental stages of a moth: the closer to adult stage, the less reproductive output

PubMed Central

Zhang, Wei; Chang, Xiang-Qian; Hoffmann, AryA.; Zhang, Shu; Ma, Chun-Sen

2015-01-01

Hot days in summer (involving a few hours at particularly high temperatures) are expected to become more common under climate change. How such events at different life stages affect survival and reproduction remains unclear in most organisms. Here, we investigated how an exposure to 40 °C at different life stages in the global insect pest, Plutella xylostella, affects immediate survival, subsequent survival and reproductive output. First-instar larvae showed the lowest survival under heat stress, whereas 3rd-instar larvae were relatively heat resistant. Heat exposure at the 1st-instar or egg stage did not influence subsequent maturation success, while exposure at the 3rd-instar larval stage did have an effect. We found that heat stress at developmental stages closer to adult stage caused greater detrimental effects on reproduction than heat stress experienced at earlier life stages. The effects of hot events on insect populations can therefore depend critically on the timing of the event relative to an organism’s life-cycle. PMID:26000790

Troglitazone induces differentiation in Trypanosoma brucei

DOE Office of Scientific and Technical Information (OSTI.GOV)

Denninger, Viola; Figarella, Katherine; Schoenfeld, Caroline

2007-05-15

Trypanosoma brucei, a protozoan parasite causing sleeping sickness, is transmitted by the tsetse fly and undergoes a complex lifecycle including several defined stages within the insect vector and its mammalian host. In the latter, differentiation from the long slender to the short stumpy form is induced by a yet unknown factor of trypanosomal origin. Here we describe that some thiazolidinediones are also able to induce differentiation. In higher eukaryotes, thiazolidinediones are involved in metabolism and differentiation processes mainly by binding to the intracellular receptor peroxisome proliferator activated receptor {gamma}. Our studies focus on the effects of troglitazone on bloodstream formmore » trypanosomes. Differentiation was monitored using mitochondrial markers (membrane potential, succinate dehydrogenase activity, inhibition of oxygen uptake by KCN, amount of cytochrome transcripts), morphological changes (Transmission EM and light microscopy), and transformation experiments (loss of the Variant Surface Glycoprotein coat and increase of dihydroliponamide dehydrogenase activity). To further investigate the mechanisms responsible for these changes, microarray analyses were performed, showing an upregulation of expression site associated gene 8 (ESAG8), a potential differentiation regulator.« less

DISPOSITION PATHS FOR ROCKY FLATS GLOVEBOXES: EVALUATING OPTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lobdell, D.; Geimer, R.; Larsen, P.

2003-02-27

The Kaiser-Hill Company, LLC has the responsibility for closure activities at the Rocky Flats Environmental Technology Site (RFETS). One of the challenges faced for closure is the disposition of radiologically contaminated gloveboxes. Evaluation of the disposition options for gloveboxes included a detailed analysis of available treatment capabilities, disposal facilities, and lifecycle costs. The Kaiser-Hill Company, LLC followed several processes in determining how the gloveboxes would be managed for disposition. Currently, multiple disposition paths have been chosen to accommodate the needs of the varying styles and conditions of the gloveboxes, meet the needs of the decommissioning team, and to best managemore » lifecycle costs. Several challenges associated with developing a disposition path that addresses both the radiological and RCRA concerns as well as offering the most cost-effective solution were encountered. These challenges included meeting the radiological waste acceptance criteria of available disposal facilities, making a RCRA determination, evaluating treatment options and costs, addressing void requirements associated with disposal, and identifying packaging and transportation options. The varying disposal facility requirements affected disposition choices. Facility conditions that impacted decisions included radiological and chemical waste acceptance criteria, physical requirements, and measurement for payment options. The facility requirements also impacted onsite activities including management strategies, decontamination activities, and life-cycle cost.« less

Development of hybrid lifecycle cost estimating tool (HLCET) for manufacturing influenced design tradeoff

NASA Astrophysics Data System (ADS)

Sirirojvisuth, Apinut

In complex aerospace system design, making an effective design decision requires multidisciplinary knowledge from both product and process perspectives. Integrating manufacturing considerations into the design process is most valuable during the early design stages since designers have more freedom to integrate new ideas when changes are relatively inexpensive in terms of time and effort. Several metrics related to manufacturability are cost, time, and manufacturing readiness level (MRL). Yet, there is a lack of structured methodology that quantifies how changes in the design decisions impact these metrics. As a result, a new set of integrated cost analysis tools are proposed in this study to quantify the impacts. Equally important is the capability to integrate this new cost tool into the existing design methodologies without sacrificing agility and flexibility required during the early design phases. To demonstrate the applicability of this concept, a ModelCenter environment is used to develop software architecture that represents Integrated Product and Process Development (IPPD) methodology used in several aerospace systems designs. The environment seamlessly integrates product and process analysis tools and makes effective transition from one design phase to the other while retaining knowledge gained a priori. Then, an advanced cost estimating tool called Hybrid Lifecycle Cost Estimating Tool (HLCET), a hybrid combination of weight-, process-, and activity-based estimating techniques, is integrated with the design framework. A new weight-based lifecycle cost model is created based on Tailored Cost Model (TCM) equations [3]. This lifecycle cost tool estimates the program cost based on vehicle component weights and programmatic assumptions. Additional high fidelity cost tools like process-based and activity-based cost analysis methods can be used to modify the baseline TCM result as more knowledge is accumulated over design iterations. Therefore, with this concept, the additional manufacturing knowledge can be used to identify a more accurate lifecycle cost and facilitate higher fidelity tradeoffs during conceptual and preliminary design. Advanced Composite Cost Estimating Model (ACCEM) is employed as a process-based cost component to replace the original TCM result of the composite part production cost. The reason for the replacement is that TCM estimates production costs from part weights as a result of subtractive manufacturing of metallic origin such as casting, forging, and machining processes. A complexity factor can sometimes be adjusted to reflect different types of metal and machine settings. The TCM assumption, however, gives erroneous results when applied to additive processes like those of composite manufacturing. Another innovative aspect of this research is the introduction of a work measurement technique called Maynard Operation Sequence Technique (MOST) to be used, similarly to Activity-Based Costing (ABC) approach, to estimate manufacturing time of a part by virtue of breaking down the operations occurred during its production. ABC allows a realistic determination of cost incurred in each activity, as opposed to using a traditional method of time estimation by analogy or using response surface equations from historical process data. The MOST concept provides a tailored study of an individual process typically required for a new, innovative design. Nevertheless, the MOST idea has some challenges, one of which is its requirement to build a new process from ground up. The process development requires a Subject Matter Expertise (SME) in manufacturing method of the particular design. The SME must have also a comprehensive understanding of the MOST system so that the correct parameters are chosen. In practice, these knowledge requirements may demand people from outside of the design discipline and a priori training of MOST. To relieve the constraint, this study includes an entirely new sub-system architecture that comprises 1) a knowledge-based system to provide the required knowledge during the process selection; and 2) a new user-interface to guide the parameter selection when building the process using MOST. Also included in this study is the demonstration of how the HLCET and its constituents can be integrated with a Georgia Tech' Integrated Product and Process Development (IPPD) methodology. The applicability of this work will be shown through a complex aerospace design example to gain insights into how manufacturing knowledge helps make better design decisions during the early stages. The setup process is explained with an example of its utility demonstrated in a hypothetical fighter aircraft wing redesign. The evaluation of the system effectiveness against existing methodologies is illustrated to conclude the thesis.

Biogenesis, maintenance and dynamics of glycosomes in trypanosomatid parasites.

PubMed

Haanstra, Jurgen R; González-Marcano, Eglys B; Gualdrón-López, Melisa; Michels, Paul A M

2016-05-01

Peroxisomes of organisms belonging to the protist group Kinetoplastea, which include trypanosomatid parasites of the genera Trypanosoma and Leishmania, are unique in playing a crucial role in glycolysis and other parts of intermediary metabolism. They sequester the majority of the glycolytic enzymes and hence are called glycosomes. Their glycosomal enzyme content can vary strongly, particularly quantitatively, between different trypanosomatid species, and within each species during its life cycle. Turnover of glycosomes by autophagy of redundant ones and biogenesis of a new population of organelles play a pivotal role in the efficient adaptation of the glycosomal metabolic repertoire to the sudden, major nutritional changes encountered during the transitions in their life cycle. The overall mechanism of glycosome biogenesis is similar to that of peroxisomes in other organisms, but the homologous peroxins involved display low sequence conservation as well as variations in motifs mediating crucial protein-protein interactions in the process. The correct compartmentalisation of enzymes is essential for the regulation of the trypanosomatids' metabolism and consequently for their viability. For Trypanosoma brucei it was shown that glycosomes also play a crucial role in its life-cycle regulation: a crucial developmental control switch involves the translocation of a protein phosphatase from the cytosol into the organelles. Many glycosomal proteins are differentially phosphorylated in different life-cycle stages, possibly indicative of regulation of enzyme activities as an additional means to adapt the metabolic network to the different environmental conditions encountered. Copyright © 2015 Elsevier B.V. All rights reserved.

[Morphology of III stage larvae of Angiostrongylus cantonensis in Pomacea canaliculata].

PubMed

Zhang, Chao-Wei; Zhou, Xiao-Nong; Lv, Shan; Zhang, Yi; Liu, He-Xiang

2008-06-30

To observe the morphologic characteristics of III stage larvae of Angiostrongylus cantonensis from Pomacea canaliculata. P. canaliculata, the intermediate host snail of A. cantonensis, was infected with I stage larvae of A. cantonensis in laboratory. After 61 days, III stage larvae of A. cantonensis were harvested from snail's lungs and muscle of head-foot, followed by HE stain to observe morphological characteristics. The whole body of III stage larva was curling with obtuse head. Its pharyngeal canal extends from the buccal hole on the top of the head to the intestines at the pharyngeal intestine joint place, with apex cauda and clear anal tube. The tegument of the III stage larva was eosin-stained, with a transparent sheath outside of tegument. Some of the larvae cauda showed in circular cylinder, and some larvae presented ventral gland with two very short uterine which used to be the feature only showed in early IV stage larva. Morphologically characteristics of the III stage larvae is helpful to better understand the life-cycle and the control of A. cantonensis.

Modular Open System Architecture for Reducing Contamination Risk in the Space and Missile Defense Supply Chain

NASA Technical Reports Server (NTRS)

Seasly, Elaine

2015-01-01

To combat contamination of physical assets and provide reliable data to decision makers in the space and missile defense community, a modular open system architecture for creation of contamination models and standards is proposed. Predictive tools for quantifying the effects of contamination can be calibrated from NASA data of long-term orbiting assets. This data can then be extrapolated to missile defense predictive models. By utilizing a modular open system architecture, sensitive data can be de-coupled and protected while benefitting from open source data of calibrated models. This system architecture will include modules that will allow the designer to trade the effects of baseline performance against the lifecycle degradation due to contamination while modeling the lifecycle costs of alternative designs. In this way, each member of the supply chain becomes an informed and active participant in managing contamination risk early in the system lifecycle.

Land processes distributed active archive center product lifecycle plan

USGS Publications Warehouse

Daucsavage, John C.; Bennett, Stacie D.

2014-01-01

The U.S. Geological Survey (USGS) Earth Resources Observation and Science (EROS) Center and the National Aeronautics and Space Administration (NASA) Earth Science Data System Program worked together to establish, develop, and operate the Land Processes (LP) Distributed Active Archive Center (DAAC) to provide stewardship for NASA’s land processes science data. These data are critical science assets that serve the land processes science community with potential value beyond any immediate research use, and therefore need to be accounted for and properly managed throughout their lifecycle. A fundamental LP DAAC objective is to enable permanent preservation of these data and information products. The LP DAAC accomplishes this by bridging data producers and permanent archival resources while providing intermediate archive services for data and information products.

Bayesian assurance and sample size determination in the process validation life-cycle.

PubMed

Faya, Paul; Seaman, John W; Stamey, James D

2017-01-01

Validation of pharmaceutical manufacturing processes is a regulatory requirement and plays a key role in the assurance of drug quality, safety, and efficacy. The FDA guidance on process validation recommends a life-cycle approach which involves process design, qualification, and verification. The European Medicines Agency makes similar recommendations. The main purpose of process validation is to establish scientific evidence that a process is capable of consistently delivering a quality product. A major challenge faced by manufacturers is the determination of the number of batches to be used for the qualification stage. In this article, we present a Bayesian assurance and sample size determination approach where prior process knowledge and data are used to determine the number of batches. An example is presented in which potency uniformity data is evaluated using a process capability metric. By using the posterior predictive distribution, we simulate qualification data and make a decision on the number of batches required for a desired level of assurance.

A PLM-based automated inspection planning system for coordinate measuring machine

NASA Astrophysics Data System (ADS)

Zhao, Haibin; Wang, Junying; Wang, Boxiong; Wang, Jianmei; Chen, Huacheng

2006-11-01

With rapid progress of Product Lifecycle Management (PLM) in manufacturing industry, automatic generation of inspection planning of product and the integration with other activities in product lifecycle play important roles in quality control. But the techniques for these purposes are laggard comparing with techniques of CAD/CAM. Therefore, an automatic inspection planning system for Coordinate Measuring Machine (CMM) was developed to improve the automatization of measuring based on the integration of inspection system in PLM. Feature information representation is achieved based on a PLM canter database; measuring strategy is optimized through the integration of multi-sensors; reasonable number and distribution of inspection points are calculated and designed with the guidance of statistic theory and a synthesis distribution algorithm; a collision avoidance method is proposed to generate non-collision inspection path with high efficiency. Information mapping is performed between Neutral Interchange Files (NIFs), such as STEP, DML, DMIS, XML, etc., to realize information integration with other activities in the product lifecycle like design, manufacturing and inspection execution, etc. Simulation was carried out to demonstrate the feasibility of the proposed system. As a result, the inspection process is becoming simpler and good result can be got based on the integration in PLM.

Preliminary Study on Kano Model in the Conceptual Design Activities for Product Lifecycle Improvement

NASA Astrophysics Data System (ADS)

Fahrul Hassan, Mohd; Rahman, M. R. A.; Arifin, A. M. T.; Ismail, A. E.; Rasidi Ibrahim, M.; Zulafif Rahim, M.; Fauzi Ahmad, Md

2017-08-01

Product manufactured with short life cycle had only one major issue, it can lead to increasing volume of waste. Day by day, this untreated waste had consumed many landfill spaces, waiting for any possible alternatives. Lack of product recovery knowledge and recyclability features imprinted into product design are one of the main reason behind all this. Sustainable awareness aspect should not just be implied into people’s mind, but also onto product design. This paper presents a preliminary study on Kano model method in the conceptual design activities to improve product lifecycle. Kano model is a survey-type method, used to analyze and distinguished product qualities or features, also how the customers may have perceived them. Three important attributes of Kano model are performance, attractive and must-be. The proposed approach enables better understanding of customer requirements while providing a way for Kano model to be integrated into engineering design to improve product’s end-of-life. Further works will be continued to provide a better lifecycle option (increase percentage of reuse, remanufacture or recycle, whereby decrease percentage of waste) of a product using Kano model approach.

Satellite on-board applications of expert systems

NASA Astrophysics Data System (ADS)

Ciarlo, A.; Donzelli, P.; Katzenbelsser, R.; Moller, B. A.

The article discusses some aspects of the on-board application of expert systems (ES) in artificial satellites. The implementation of two prototypes on a dedicated AI machine are described. Consideration is given to: (1) the interrelationship between the ES and the architecture of the satellite and its impact on the mission-definition phase of the satellite life-cycle; (2) the identification of those tasks that at the current stage seem most likely to be delegated to on-board ES; and (3) the main obstacles that need to be overcome before operational use of ES on-board can take place, and particularly the matters of testing, knowledge collection, and availability of computing resources. Finally, the activities that are currently planned or that appear to be required in the near future to prepare the way for the full exploitation of this technology for satellite autonomy are briefly outlined.

Technology requirements for advanced earth-orbital transportation systems, dual-mode propulsion

NASA Technical Reports Server (NTRS)

Haefeli, R. C.; Littler, E. G.; Hurley, J. B.; Winter, M. G.

1977-01-01

The application of dual-mode propulsion concepts to fully reusable single-stage-to-orbit (SSTO) vehicles is discussed. Dual-mode propulsion uses main rocket engines that consume hydrocarbon fuels as well as liquid hydrogen fuel. Liquid oxygen is used as the oxidizer. These engine concepts were integrated into transportation vehicle designs capable of vertical takeoff, delivering a payload to earth orbit, and return to earth with a horizontal landing. Benefits of these vehicles were assessed and compared with vehicles using single-mode propulsion (liquid hydrogen and oxygen engines). Technology requirements for such advanced transportation systems were identified. Figures of merit, including life-cycle cost savings and research costs, were derived for dual-mode technology programs, and were used for assessments of potential benefits of proposed technology activities. Dual-mode propulsion concepts display potential for significant cost and performance benefits when applied to SSTO vehicles.

Geospatial Standards and the Knowledge Generation Lifescycle

NASA Technical Reports Server (NTRS)

Khalsa, Siri Jodha S.; Ramachandran, Rahul

2014-01-01

Standards play an essential role at each stage in the sequence of processes by which knowledge is generated from geoscience observations, simulations and analysis. This paper provides an introduction to the field of informatics and the knowledge generation lifecycle in the context of the geosciences. In addition we discuss how the newly formed Earth Science Informatics Technical Committee is helping to advance the application of standards and best practices to make data and data systems more usable and interoperable.

Perspectives on the design of safer nanomaterials and manufacturing processes

NASA Astrophysics Data System (ADS)

Geraci, Charles; Heidel, Donna; Sayes, Christie; Hodson, Laura; Schulte, Paul; Eastlake, Adrienne; Brenner, Sara

2015-09-01

A concerted effort is being made to insert Prevention through Design principles into discussions of sustainability, occupational safety and health, and green chemistry related to nanotechnology. Prevention through Design is a set of principles, which includes solutions to design out potential hazards in nanomanufacturing including the design of nanomaterials, and strategies to eliminate exposures and minimize risks that may be related to the manufacturing processes and equipment at various stages of the lifecycle of an engineered nanomaterial.

Canadian Consensus on Female Nutrition: Adolescence, Reproduction, Menopause, and Beyond.

PubMed

O'Connor, Deborah L; Blake, Jennifer; Bell, Rhonda; Bowen, Angela; Callum, Jeannie; Fenton, Shanna; Gray-Donald, Katherine; Rossiter, Melissa; Adamo, Kristi; Brett, Kendra; Khatri, Nasreen; Robinson, Nicole; Tumback, Lindsay; Cheung, Anthony

2016-06-01

To provide health care professionals in Canada with the basic knowledge and tools to provide nutrition guidance to women through their lifecycle. Optimal nutrition through the female lifecycle was evaluated, with specific focus on adolescence, pre-conception, pregnancy, postpartum, menopause, and beyond. The guideline begins with an overview of guidance for all women, followed by chapters that examine the evidence and provide recommendations for the promotion of healthy nutrition and body weight at each life stage. Nutrients of special concern and other considerations unique to each life stage are discussed in each chapter. Published literature, governmental and health agency reports, clinical practice guidelines, grey literature, and textbook sources were used in supporting the recommendations made in this document. The quality of evidence was rated using the criteria described in the report of the Canadian Task Force on Preventive Health Care. CHAPTER 2: GENERAL FEMALE NUTRITION: Summary Statements Recommendations CHAPTER 3: ADOLESCENCE NUTRITION: Summary Statements Recommendations CHAPTER 4: PRE-CONCEPTUAL NUTRITION: Summary Statement Recommendations CHAPTER 5: NUTRITION IN PREGNANCY: Summary Statements Recommendations CHAPTER 6: POSTPARTUM NUTRITION AND LACTATION: Summary Statements Recommendations CHAPTER 7: NUTRITION DURING MENOPAUSE AND BEYOND: Summary Statement Recommendations. Copyright © 2016 The Society of Obstetricians and Gynaecologists of Canada/La Société des obstétriciens et gynécologues du Canada. Published by Elsevier Inc. All rights reserved.

Altered expression of an RBP-associated arginine methyltransferase 7 in Leishmania major affects parasite infection.

PubMed

Ferreira, Tiago R; Alves-Ferreira, Eliza V C; Defina, Tania P A; Walrad, Pegine; Papadopoulou, Barbara; Cruz, Angela K

2014-10-08

Protein arginine methylation is a widely conserved post-translational modification performed by arginine methyltransferases (PRMTs). However, its functional role in parasitic protozoa is still under-explored. The Leishmania major genome encodes five PRMT homologs, including PRMT7. Here we show that LmjPRMT7 expression and arginine monomethylation are tightly regulated in a lifecycle stage-dependent manner. LmjPRMT7 levels are higher during the early promastigote logarithmic phase, negligible at stationary and late-stationary phases and rise once more post-differentiation to intracellular amastigotes. Immunofluorescence and co-immunoprecipitation studies demonstrate that LmjPRMT7 is a cytosolic protein associated with several RNA-binding proteins (RBPs) from which Alba20 is monomethylated only in LmjPRMT7-expressing promastigote stages. In addition, Alba20 protein levels are significantly altered in stationary promastigotes of the LmjPRMT7 knockout mutant. Considering RBPs are well-known mammalian PRMT substrates, our data suggest that arginine methylation via LmjPRMT7 may modulate RBP function during Leishmania spp. lifecycle progression. Importantly, genomic deletion of the LmjPRMT7 gene leads to an increase in parasite infectivity both in vitro and in vivo, while lesion progression is significantly reduced in LmjPRMT7-overexpressing parasites. This study is the first to describe a role of Leishmania protein arginine methylation in host-parasite interactions. © 2014 John Wiley & Sons Ltd.

Human-Centered Design Capability

NASA Technical Reports Server (NTRS)

Fitts, David J.; Howard, Robert

2009-01-01

For NASA, human-centered design (HCD) seeks opportunities to mitigate the challenges of living and working in space in order to enhance human productivity and well-being. Direct design participation during the development stage is difficult, however, during project formulation, a HCD approach can lead to better more cost-effective products. HCD can also help a program enter the development stage with a clear vision for product acquisition. HCD tools for clarifying design intent are listed. To infuse HCD into the spaceflight lifecycle the Space and Life Sciences Directorate developed the Habitability Design Center. The Center has collaborated successfully with program and project design teams and with JSC's Engineering Directorate. This presentation discusses HCD capabilities and depicts the Center's design examples and capabilities.

Commercialization, patents and moral assessment of biotechnology products.

PubMed

Hoedemaekers, R

2001-06-01

The biotechnology patent debates have revealed deep moral concerns about basic genetics research, R&D and specific biotechnological products, concerns that are seldom taken into consideration in Technology Assessment. In this paper important moral concerns are examined which appear at the various stages of development of a specific genetic product: a predictive genetic test. The purpose is to illustrate the need for a more contextual approach in technology assessment, which integrates the various forms of interaction between bio-technology and society or societal segments. Such an approach will generate greater insight in the moral issues at all stages of a product's life-cycle and this will facilitate decision-making on the 'morality' of a specific biotechnological product.

32 CFR 651.5 - Army policies.

Code of Federal Regulations, 2011 CFR

2011-07-01

... retain environmental analyses and data from requirements determination activities, and Science and... environmental analysis of acquisition life-cycle activities (including disposal). Planning to accomplish these... required, throughout the life cycle of the system. The MATDEV will coordinate with ASA (AL&T) or MACOM...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT...-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures..., including lower life-cycle costs, positive net savings, savings-to-investment ratio that is estimated to be...

77 FR 38766 - Proposed Information Collection; Comment Request; International Client Life-Cycle Multi-Purpose...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... Request; International Client Life-Cycle Multi-Purpose Forms AGENCY: International Trade Administration... aspects of an international organization's life-cycle with CS. CS is mandated by Congress to help U.S... trade events to U.S. organizations. The International Client Life-cycle Multi-Purpose Forms, previously...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT... BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures...

77 FR 38582 - Proposed Information Collection; Comment Request; Domestic Client Life-Cycle Multi-Purpose Forms

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-28

... Request; Domestic Client Life-Cycle Multi-Purpose Forms AGENCY: International Trade Administration. ACTION... life-cycle with CS. CS is mandated by Congress to help U.S. organizations, particularly small and... Client Life-cycle Multi-Purpose Forms, previously titled Export Information Services Order Forms, are...

10 CFR 435.8 - Life-cycle costing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle costing. 435.8 Section 435.8 Energy DEPARTMENT... BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures...

Alternative Fuels Data Center: Lifecycle Energy Balance

Science.gov Websites

Energy Balance to someone by E-mail Share Alternative Fuels Data Center: Lifecycle Energy Balance on Facebook Tweet about Alternative Fuels Data Center: Lifecycle Energy Balance on Twitter Bookmark Alternative Fuels Data Center: Lifecycle Energy Balance on Google Bookmark Alternative Fuels Data Center

Cybersecurity and the Medical Device Product Development Lifecycle.

PubMed

Jones, Richard W; Katzis, Konstantinos

2017-01-01

Protecting connected medical devices from evolving cyber related threats, requires a continuous lifecycle approach whereby cybersecurity is integrated within the product development lifecycle and both complements and re-enforces the safety risk management processes therein. This contribution reviews the guidance relating to medical device cybersecurity within the product development lifecycle.

Identification and characterisation of the ecdysone biosynthetic genes neverland, disembodied and shade in the salmon louse Lepeophtheirus salmonis (Copepoda, Caligidae)

PubMed Central

Kongshaug, Heidi; Horsberg, Tor Einar; Male, Rune; Nilsen, Frank; Dalvin, Sussie

2018-01-01

The salmon louse is a marine ectoparasitic copepod on salmonid fishes. Its lifecycle consists of eight developmental stages, each separated by a molt. In crustaceans and insects, molting and reproduction is controlled by circulating steroid hormones such as 20-hydroxyecdysone. Steroid hormones are synthesized from cholesterol through catalytic reactions involving a 7,8-dehydrogenase Neverland and several cytochrome P450 genes collectively called the Halloween genes. In this study, we have isolated and identified orthologs of neverland, disembodied and shade in the salmon louse (Lepeophtheirus salmonis) genome. Tissue-specific expression analysis show that the genes are expressed in intestine and reproductive tissue. In addition, levels of the steroid hormones ecdysone, 20-hydroxyecdysone and ponasterone A were measured during the reproductive stage of adult females and in early life stages. PMID:29401467

The Air-Carbon-Water Synergies and Trade-Offs in China's Natural Gas Industry

NASA Astrophysics Data System (ADS)

Qin, Yue

China's coal-dominated energy structure is partly responsible for its domestic air pollution, local water stress, and the global climate change. Primarily to tackle the haze issue, China has been actively promoting a nationwide coal to natural gas end-use switch. My dissertation focuses on evaluating the air quality, carbon, and water impacts and their interactions in China's natural gas industry. Chapter 2 assesses the lifecycle climate performance of China's shale gas in comparison to coal based on stage-level energy consumption and methane leakage rates. I find the mean lifecycle carbon footprint of shale gas is about 30-50% lower than that of coal under both 20 year and 100 year global warming potentials (GWP20 and GWP100). However, primarily due to large uncertainties in methane leakage, the lifecycle carbon footprint of shale gas in China could be 15-60% higher than that of coal across sectors under GWP20. Chapter 3 evaluates the air quality, human health, and the climate impacts of China's coal-based synthetic natural gas (SNG) development. Based on earlier 2020 SNG production targets, I conduct an integrated assessment to identify production technologies and end-use applications that will bring as large air quality and health benefits as possible while keeping carbon penalties as small as possible. I find that, due to inefficient and uncontrolled coal combustion in households, allocating currently available SNG to the residential sector proves to be the best SNG allocation option. Chapter 4 compares the air quality, carbon, and water impacts of China's six major gas sources under three end-use substitution scenarios, which are focused on maximizing air pollutant emission reductions, CO 2 emission reductions, and water stress index (WSI)-weighted water consumption reductions, respectively. I find striking national air-carbon/water trade-offs due to SNG, which also significantly increases water demands and carbon emissions in regions already suffering from severe water stress and having the largest per capita carbon footprint. Gas sources other than SNG may bring national air-carbon-water co-benefits. However, end-use deployment can cause enormous variations in air quality, carbon, and water impacts, with notable air-carbon synergies but air-water trade-offs.

Estimating net changes in life-cycle emissions from adoption of emerging civil infrastructure technologies.

PubMed

Amponsah, Isaac; Harrison, Kenneth W; Rizos, Dimitris C; Ziehl, Paul H

2008-01-01

There is a net emissions change when adopting new materials for use in civil infrastructure design. To evaluate the total net emissions change, one must consider changes in manufacture and associated life-cycle emissions, as well as changes in the quantity of material required. In addition, in principle one should also consider any differences in costs of the two designs because cost savings can be applied to other economic activities with associated environmental impacts. In this paper, a method is presented that combines these considerations to permit an evaluation of the net change in emissions when considering the adoption of emerging technologies/materials for civil infrastructure. The method factors in data on differences between a standard and new material for civil infrastructure, material requirements as specified in designs using both materials, and price information. The life-cycle assessment approach known as economic input-output life-cycle assessment (EIO-LCA) is utilized. A brief background on EIO-LCA is provided because its use is central to the method. The methodology is demonstrated with analysis of a switch from carbon steel to high-performance steel in military bridge design. The results are compared with a simplistic analysis that accounts for the weight reduction afforded by use of the high-performance steel but assuming no differences in manufacture.

UCT943, a next generation Plasmodium falciparum PI4K inhibitor preclinical candidate for the treatment of malaria.

PubMed

Brunschwig, Christel; Lawrence, Nina; Taylor, Dale; Abay, Efrem; Njoroge, Mathew; Basarab, Gregory S; Le Manach, Claire; Paquet, Tanya; Gonzàlez Cabrera, Diego; Nchinda, Aloysius T; de Kock, Carmen; Wiesner, Lubbe; Denti, Paolo; Waterson, David; Blasco, Benjamin; Leroy, Didier; Witty, Michael J; Donini, Cristina; Duffy, James; Wittlin, Sergio; White, Karen L; Charman, Susan A; Jiménez-Díaz, Maria Belén; Angulo-Barturen, Iñigo; Herreros, Esperanza; Gamo, Francisco Javier; Rochford, Rosemary; Mancama, Dalu; Coetzer, Theresa L; van der Watt, Mariëtte E; Reader, Janette; Birkholtz, Lyn-Marie; Marsh, Kennan C; Solapure, Suresh M; Vanaerschot, Manu; Fidock, David A; Fish, Paul V; Siegl, Peter; Smith, Dennis A; Wirjanata, Grennady; Noviyanti, Rintis; Price, Ric N; Marfurt, Jutta; Silue, Kigbafori D; Street, Leslie J; Chibale, Kelly

2018-06-25

The 2-aminopyridine MMV048 was the first drug candidate inhibiting Plasmodium phosphatidylinositol 4-kinase (PI4K), a novel drug target for malaria, to enter clinical development. In an effort to identify the next generation of PI4K inhibitors, the series was optimized to improve properties such as solubility and antiplasmodial potency across the parasite lifecycle, leading to the 2-aminopyrazine UCT943. The compound displayed higher asexual blood stage, transmission-blocking, and liver stage activity than MMV048 and was more potent against resistant P. falciparum and P. vivax clinical isolates. Excellent in vitro antiplasmodial activity translated into high efficacy in P. berghei and humanized P. falciparum NOD- scid IL-2Rγ null mouse models. The high passive permeability and high aqueous solubility of UCT943, combined with low to moderate in vitro intrinsic clearance, resulted in sustained exposure and high bioavailability in preclinical species. In addition, the predicted human dose for a curative single administration using monkey and dog pharmacokinetics was low, ranging from 50 to 80 mg. As a next generation Plasmodium PI4K inhibitor, the combined preclinical data suggest that UCT943 has the potential to form part of a single-exposure radical cure and prophylaxis (SERCaP) to treat, prevent and block the transmission of malaria. Copyright © 2018 American Society for Microbiology.

32 CFR Appendix to Part 162 - Reporting Procedures

Code of Federal Regulations, 2014 CFR

2014-07-01

... generated. e. Projected Life-Cycle Savings. For each PIF project provide the estimated amount of savings the project is projected to earn over the project's economic life. f. Projected Life-Cycle Cost Avoidance. For... Projected Life-Cycle Savings. e. Total Projected Life-Cycle Cost Avoidance. 3. CSI. Each DoD Component that...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life... choose to use any of four methods, including lower life-cycle costs, positive net savings, savings-to...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures set out in subpart A...

10 CFR 433.8 - Life-cycle costing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle costing. 433.8 Section 433.8 Energy DEPARTMENT... FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.8 Life-cycle costing. Each Federal agency shall determine life-cycle cost-effectiveness by using the procedures set out in subpart A...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...) ENERGY STAR qualified and FEMP designated products may be assumed to be life-cycle cost-effective. (b) In...

10 CFR 436.42 - Evaluation of Life-Cycle Cost Effectiveness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the life-cycle cost analysis method in part 436, subpart A, of title 10 of the Code of Federal... 10 Energy 3 2011-01-01 2011-01-01 false Evaluation of Life-Cycle Cost Effectiveness. 436.42... PROGRAMS Agency Procurement of Energy Efficient Products § 436.42 Evaluation of Life-Cycle Cost...

Processes affecting altitudinal distribution of invasive Ageratina adenophora in western Himalaya: The role of local adaptation and the importance of different life-cycle stages

PubMed Central

Kühn, Ingolf; Ahmad, Mustaqeem; Michalski, Stefan; Auge, Harald

2017-01-01

The spread of invasive plants along elevational gradients is considered a threat to fragile mountain ecosystems, but it can also provide the opportunity to better understand some of the basic processes driving the success of invasive species. Ageratina adenophora (Asteraceae) is an invasive plant of global importance and has a broad distribution along elevational gradients in the Western Himalayas. Our study aimed at understanding the role of evolutionary processes (e.g. local adaptation and clinal differentiation) and different life history stages in shaping the distribution pattern of the invasive plant along an elevational gradient in the Western Himalaya. We carried out extensive distributional surveys, established a reciprocal transplant experiment with common gardens at three elevational levels, and measured a suite of traits related to germination, growth, reproduction and phenology. Our results showed a lack of local adaptation, and we did not find any evidence for clinal differentiation in any measured trait except a rather weak signal for plant height. We found that seed germination was the crucial life-cycle transition in determining the lower range limit while winter mortality of plants shaped the upper range limit in our study area, thus explaining the hump shaped distribution pattern. Differences in trait values between gardens for most traits indicated a high degree of phenotypic plasticity. Possible causes such as apomixis, seed dispersal among sites, and pre-adaptation might have confounded evolutionary processes to act upon. Our results suggest that the success and spread of Ageratina adenophora are dependent on different life history stages at different elevations that are controlled by abiotic conditions. PMID:29125852

Processes affecting altitudinal distribution of invasive Ageratina adenophora in western Himalaya: The role of local adaptation and the importance of different life-cycle stages.

PubMed

Datta, Arunava; Kühn, Ingolf; Ahmad, Mustaqeem; Michalski, Stefan; Auge, Harald

2017-01-01

The spread of invasive plants along elevational gradients is considered a threat to fragile mountain ecosystems, but it can also provide the opportunity to better understand some of the basic processes driving the success of invasive species. Ageratina adenophora (Asteraceae) is an invasive plant of global importance and has a broad distribution along elevational gradients in the Western Himalayas. Our study aimed at understanding the role of evolutionary processes (e.g. local adaptation and clinal differentiation) and different life history stages in shaping the distribution pattern of the invasive plant along an elevational gradient in the Western Himalaya. We carried out extensive distributional surveys, established a reciprocal transplant experiment with common gardens at three elevational levels, and measured a suite of traits related to germination, growth, reproduction and phenology. Our results showed a lack of local adaptation, and we did not find any evidence for clinal differentiation in any measured trait except a rather weak signal for plant height. We found that seed germination was the crucial life-cycle transition in determining the lower range limit while winter mortality of plants shaped the upper range limit in our study area, thus explaining the hump shaped distribution pattern. Differences in trait values between gardens for most traits indicated a high degree of phenotypic plasticity. Possible causes such as apomixis, seed dispersal among sites, and pre-adaptation might have confounded evolutionary processes to act upon. Our results suggest that the success and spread of Ageratina adenophora are dependent on different life history stages at different elevations that are controlled by abiotic conditions.

Wind turbine blade waste in 2050.

PubMed

Liu, Pu; Barlow, Claire Y

2017-04-01

Wind energy has developed rapidly over the last two decades to become one of the most promising and economically viable sources of renewable energy. Although wind energy is claimed to provide clean renewable energy without any emissions during operation, but it is only one side of the coin. The blades, one of the most important components in the wind turbines, made with composite, are currently regarded as unrecyclable. With the first wave of early commercial wind turbine installations now approaching their end of life, the problem of blade disposal is just beginning to emerge as a significant factor for the future. This paper is aimed at discovering the magnitude of the wind turbine blade waste problem, looking not only at disposal but at all stages of a blade's lifecycle. The first stage of the research, the subject of this paper, is to accurately estimate present and future wind turbine blade waste inventory using the most recent and most accurate data available. The result will provide a solid reference point to help the industry and policy makers to understand the size of potential environmental problem and to help to manage it better. This study starts by estimating the annual blade material usage with wind energy installed capacity and average blade weight. The effect of other waste contributing factors in the full lifecycle of wind turbine blades is then included, using industrial data from the manufacturing, testing and in-service stages. The research indicates that there will be 43 million tonnes of blade waste worldwide by 2050 with China possessing 40% of the waste, Europe 25%, the United States 16% and the rest of the world 19%. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Life-cycle assessment of transportation biofuels from hydrothermal liquefaction of forest residues in British Columbia.

PubMed

Nie, Yuhao; Bi, Xiaotao

2018-01-01

Biofuels from hydrothermal liquefaction (HTL) of abundantly available forest residues in British Columbia (BC) can potentially make great contributions to reduce the greenhouse gas (GHG) emissions from the transportation sector. A life-cycle assessment was conducted to quantify the GHG emissions of a hypothetic 100 million liters per year HTL biofuel system in the Coast Region of BC. Three scenarios were defined and investigated, namely, supply of bulky forest residues for conversion in a central integrated refinery (Fr-CIR), HTL of forest residues to bio-oil in distributed biorefineries and subsequent upgrading in a central oil refinery (Bo-DBR), and densification of forest residues in distributed pellet plants and conversion in a central integrated refinery (Wp-CIR). The life-cycle GHG emissions of HTL biofuels is 20.5, 17.0, and 19.5 g CO 2 -eq/MJ for Fr-CIR, Bo-DBR, and Wp-CIR scenarios, respectively, corresponding to 78-82% reduction compared with petroleum fuels. The conversion stage dominates the total GHG emissions, making up more than 50%. The process emitting most GHGs over the life cycle of HTL biofuels is HTL buffer production. Transportation emission, accounting for 25% of Fr-CIR, can be lowered by 83% if forest residues are converted to bio-oil before transportation. When the credit from biochar applied for soil amendment is considered, a further reduction of 6.8 g CO 2 -eq/MJ can be achieved. Converting forest residues to bio-oil and wood pellets before transportation can significantly lower the transportation emission and contribute to a considerable reduction of the life-cycle GHG emissions. Process performance parameters (e.g., HTL energy requirement and biofuel yield) and the location specific parameter (e.g., electricity mix) have significant influence on the GHG emissions of HTL biofuels. Besides, the recycling of the HTL buffer needs to be investigated to further improve the environmental performance of HTL biofuels.

Multi-objective optimization integrated with life cycle assessment for rainwater harvesting systems

NASA Astrophysics Data System (ADS)

Li, Yi; Huang, Youyi; Ye, Quanliang; Zhang, Wenlong; Meng, Fangang; Zhang, Shanxue

2018-03-01

The major limitation of optimization models applied previously for rainwater harvesting (RWH) systems is the systematic evaluation of environmental and human health impacts across all the lifecycle stages. This study integrated life cycle assessment (LCA) into a multi-objective optimization model to optimize the construction areas of green rooftops, porous pavements and green lands in Beijing of China, considering the trade-offs among 24 h-interval RWH volume (QR), stormwater runoff volume control ratio (R), economic cost (EC), and environmental impacts (EI). Eleven life cycle impact indicators were assessed with a functional unit of 10,000 m2 of RWH construction areas. The LCA results showed that green lands performed the smallest lifecycle impacts of all assessment indicators, in contrast, porous pavements showed the largest impact values except Abiotic Depletion Potential (ADP) elements. Based on the standardization results, ADP fossil was chosen as the representative indicator for the calculation of EI objective in multi-objective optimization model due to its largest value in all RWH systems lifecycle. The optimization results for QR, R, EC and EI were 238.80 million m3, 78.5%, 66.68 billion RMB Yuan, and 1.05E + 16 MJ, respectively. After the construction of optimal RWH system, 14.7% of annual domestic water consumption and 78.5% of maximum daily rainfall would be supplied and controlled in Beijing, respectively, which would make a great contribution to reduce the stress of water scarcity and water logging problems. Green lands have been the first choice for RWH in Beijing according to the capacity of rainwater harvesting and less environmental and human impacts. Porous pavements played a good role in water logging alleviation (R for 67.5%), however, did not show a large construction result in this study due to the huge ADP fossil across the lifecycle. Sensitivity analysis revealed the daily maximum precipitation to be key factor for the robustness of the results for three RWH systems construction in this study.

Differential gene transcription across the life cycle in Daphnia magna using a new all genome custom-made microarray.

PubMed

Campos, Bruno; Fletcher, Danielle; Piña, Benjamín; Tauler, Romà; Barata, Carlos

2018-05-18

Unravelling the link between genes and environment across the life cycle is a challenging goal that requires model organisms with well-characterized life-cycles, ecological interactions in nature, tractability in the laboratory, and available genomic tools. Very few well-studied invertebrate model species meet these requirements, being the waterflea Daphnia magna one of them. Here we report a full genome transcription profiling of D. magna during its life-cycle. The study was performed using a new microarray platform designed from the complete set of gene models representing the whole transcribed genome of D. magna. Up to 93% of the existing 41,317 D. magna gene models showed differential transcription patterns across the developmental stages of D. magna, 59% of which were functionally annotated. Embryos showed the highest number of unique transcribed genes, mainly related to DNA, RNA, and ribosome biogenesis, likely related to cellular proliferation and morphogenesis of the several body organs. Adult females showed an enrichment of transcripts for genes involved in reproductive processes. These female-specific transcripts were essentially absent in males, whose transcriptome was enriched in specific genes of male sexual differentiation genes, like doublesex. Our results define major characteristics of transcriptional programs involved in the life-cycle, differentiate males and females, and show that large scale gene-transcription data collected in whole animals can be used to identify genes involved in specific biological and biochemical processes.

First in vitro cycle of the chicken mite, Dermanyssus gallinae (DeGeer 1778), utilizing an artificial feeding device.

PubMed

Bruneau, A; Dernburg, A; Chauve, C; Zenner, L

2001-12-01

The red poultry mite, Dermanyssus gallinae, is one of the most economically deleterious ecto-parasites of layer hens worldwide. D. gallinae is difficult to eliminate from infested poultry farms, and even to study, because it resides on the host only during the bloodmeal at night, and hides in the crevices of poultry houses during the day. Here, the life-cycle of D. gallinae was reproduced entirely in vitro. Mites were incubated in a glass pipette at 30 degrees C, 60-95 degrees relative humidity and total darkness. A feeding apparatus, composed of a membrane, reservoir and blood was fitted on the pipette during bloodmeals. We tested feeding rates on blood mixed with 1 of 3 anti-coagulants (EDTA, heparin and trisodium citrate) at different concentrations, and biological and artificial membranes. The best engorgement and survival rates for all 3 haematophagous life-stages of the parasite were observed in 1-day-old chick membranes and heparinized (0.02 mmo/ml) blood. We then describe the steps in developing a complete self-sustaining in vitro life-cycle. A colony of mites was maintained in vitro for 7 generations. Losses in the first generation were heavy, but survival had multiplied 5-fold by the fifth generation. We hypothesize that heavy mortality rates during the first life-cycle correspond to selective pressure: only the mites which fed and survived in vitro were able to reproduce.

FDA 2011 process validation guidance: lifecycle compliance model.

PubMed

Campbell, Cliff

2014-01-01

This article has been written as a contribution to the industry's efforts in migrating from a document-driven to a data-driven compliance mindset. A combination of target product profile, control engineering, and general sum principle techniques is presented as the basis of a simple but scalable lifecycle compliance model in support of modernized process validation. Unit operations and significant variables occupy pole position within the model, documentation requirements being treated as a derivative or consequence of the modeling process. The quality system is repositioned as a subordinate of system quality, this being defined as the integral of related "system qualities". The article represents a structured interpretation of the U.S. Food and Drug Administration's 2011 Guidance for Industry on Process Validation and is based on the author's educational background and his manufacturing/consulting experience in the validation field. The U.S. Food and Drug Administration's Guidance for Industry on Process Validation (2011) provides a wide-ranging and rigorous outline of compliant drug manufacturing requirements relative to its 20(th) century predecessor (1987). Its declared focus is patient safety, and it identifies three inter-related (and obvious) stages of the compliance lifecycle. Firstly, processes must be designed, both from a technical and quality perspective. Secondly, processes must be qualified, providing evidence that the manufacturing facility is fully "roadworthy" and fit for its intended purpose. Thirdly, processes must be verified, meaning that commercial batches must be monitored to ensure that processes remain in a state of control throughout their lifetime.

Microfluidics for Drug Discovery and Development: From Target Selection to Product Lifecycle Management

PubMed Central

Kang, Lifeng; Chung, Bong Geun; Langer, Robert; Khademhosseini, Ali

2009-01-01

Microfluidic technologies’ ability to miniaturize assays and increase experimental throughput have generated significant interest in the drug discovery and development domain. These characteristics make microfluidic systems a potentially valuable tool for many drug discovery and development applications. Here, we review the recent advances of microfluidic devices for drug discovery and development and highlight their applications in different stages of the process, including target selection, lead identification, preclinical tests, clinical trials, chemical synthesis, formulations studies, and product management. PMID:18190858

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Life-cycle cost methodology. 455.64 Section 455.64 Energy..., Hospitals, Units of Local Government, and Public Care Institutions § 455.64 Life-cycle cost methodology. (a) The life-cycle cost methodology under § 455.63(b) of this part is a systematic comparison of the...

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Life-cycle cost methodology. 455.64 Section 455.64 Energy..., Hospitals, Units of Local Government, and Public Care Institutions § 455.64 Life-cycle cost methodology. (a) The life-cycle cost methodology under § 455.63(b) of this part is a systematic comparison of the...

UTILITY OF A FULL LIFE-CYCLE COPEPOD BIOASSAY APPROACH FOR ASSESSMENT OF SEDIMENT-ASSOCIATED CONTAMINANT MIXTURES. (R825279)

EPA Science Inventory

Abstract

We compared a 21 day full life-cycle bioassay with an existing 14 day partial life-cycle bioassay for two species of meiobenthic copepods, Microarthridion littorale and Amphiascus tenuiremis. We hypothesized that full life-cycle tests would bette...

POEMS: A Case Study of an Italian Wine-Producing Firm

NASA Astrophysics Data System (ADS)

Ardente, Fulvio; Beccali, Giorgio; Cellura, Maurizio; Marvuglia, Antonino

2006-09-01

Over the last decade, researchers paid much attention to concepts such as Design for Environment, Extended Producer Responsibility, Responsible Chain Management, and Eco-design. Many management tools and standards (such as EMAS, ISO 14001, LCA, EPD, Ecolabel) have been developed to support companies in the evaluation and management of their environmental performance and to pursue continual environmental improvement. The more recent development of the aforesaid fields looks at interorganizational environmental management. Such an approach can complement the more traditional intraorganizational corporate environmental management approaches and tools. A typical example of this new trend is the Product Oriented Environmental Management System (POEMS), which represents the natural evolution of the above-mentioned tools, combining the features of EMS, EPD and Ecolabel. Although the structure of the POEMS is still not standardized, many experimental applications have yet been carried out in Europe. In developing a POEMS, a company needs to determine all of the environmental impacts caused at all life-cycle stages of the product and, ideally, to reduce all of them through a continual commitment. The aim of the present study was to perform a survey of the developed POEMS models and to analyze their peculiarities and drawbacks in the application to Small and Medium Enterprises. A case study regarding an Italian winery company is presented. The study analyzes the structure and the activities of the examined firm, in order to estimate direct and indirect environmental impacts following a life-cycle approach. The chosen functional unit is a 0.75-L bottle of red wine. The article also suggests some solutions to improve the environmental performances of the firm’s products.

POEMS: a case study of an Italian wine-producing firm.

PubMed

Ardente, Fulvio; Beccali, Giorgio; Cellura, Maurizio; Marvuglia, Antonino

2006-09-01

Over the last decade, researchers paid much attention to concepts such as Design for Environment, Extended Producer Responsibility, Responsible Chain Management, and Eco-design. Many management tools and standards (such as EMAS, ISO 14001, LCA, EPD, Ecolabel) have been developed to support companies in the evaluation and management of their environmental performance and to pursue continual environmental improvement. The more recent development of the aforesaid fields looks at interorganizational environmental management. Such an approach can complement the more traditional intraorganizational corporate environmental management approaches and tools. A typical example of this new trend is the Product Oriented Environmental Management System (POEMS), which represents the natural evolution of the above-mentioned tools, combining the features of EMS, EPD and Ecolabel. Although the structure of the POEMS is still not standardized, many experimental applications have yet been carried out in Europe. In developing a POEMS, a company needs to determine all of the environmental impacts caused at all life-cycle stages of the product and, ideally, to reduce all of them through a continual commitment. The aim of the present study was to perform a survey of the developed POEMS models and to analyze their peculiarities and drawbacks in the application to Small and Medium Enterprises. A case study regarding an Italian winery company is presented. The study analyzes the structure and the activities of the examined firm, in order to estimate direct and indirect environmental impacts following a life-cycle approach. The chosen functional unit is a 0.75-L bottle of red wine. The article also suggests some solutions to improve the environmental performances of the firm's products.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldsmith, John E. M.; Brennan, James S.; Brubaker, Erik

A wide range of NSC (Neutron Scatter Camera) activities were conducted under this lifecycle plan. This document outlines the highlights of those activities, broadly characterized as system improvements, laboratory measurements, and deployments, and presents sample results in these areas. Additional information can be found in the documents that reside in WebPMIS.

Life-Cycle Traits of Paraleucilla magna, a Calcareous Sponge Invasive in a Coastal Mediterranean Basin

PubMed Central

Longo, Caterina; Pontassuglia, Carmen; Corriero, Giuseppe; Gaino, Elda

2012-01-01

The calcareous sponge Paraleucilla magna, originally observed along the Brazilian coast (Atlantic Ocean), is the only allochthonous invasive species of Porifera reported in the Mediterranean Sea. A 1-year investigation of the population dynamics and life-cycle of this exotic species in the Mar Piccolo di Taranto (southern Italy, central Mediterranean Sea) has provided a good opportunity to test how environmental variations can influence its life-cycle and to ascertain what strategy can be adopted to successfully colonize a new environment. In the Mar Piccolo di Taranto, P. magna exhibits marked temporal changes in biomass. The studied specimens reproduce almost all year round, showing a seasonal pattern that peaks during warm months. This prolonged sexual activity allows P. magna to continuously produce young specimens, with repeated recruitment events taking place throughout the year, thus offsetting the seasonal mortality of adult specimens. This r-strategy enables the non-indigenous sponge to achieve a high degree of maintenance over relatively long periods (ten years at least). PMID:22905128

Mealworms in the Classroom.

ERIC Educational Resources Information Center

McGlathery, Glenn

1989-01-01

Describes a lesson in which the life-cycle of an insect is studied. Provides information on the purchase and care of the animal and directions for student observations. Questions and activities are included. (RT)

Understanding future emissions from low-carbon power systems by integration of life-cycle assessment and integrated energy modelling

NASA Astrophysics Data System (ADS)

Pehl, Michaja; Arvesen, Anders; Humpenöder, Florian; Popp, Alexander; Hertwich, Edgar G.; Luderer, Gunnar

2017-12-01

Both fossil-fuel and non-fossil-fuel power technologies induce life-cycle greenhouse gas emissions, mainly due to their embodied energy requirements for construction and operation, and upstream CH4 emissions. Here, we integrate prospective life-cycle assessment with global integrated energy-economy-land-use-climate modelling to explore life-cycle emissions of future low-carbon power supply systems and implications for technology choice. Future per-unit life-cycle emissions differ substantially across technologies. For a climate protection scenario, we project life-cycle emissions from fossil fuel carbon capture and sequestration plants of 78-110 gCO2eq kWh-1, compared with 3.5-12 gCO2eq kWh-1 for nuclear, wind and solar power for 2050. Life-cycle emissions from hydropower and bioenergy are substantial (˜100 gCO2eq kWh-1), but highly uncertain. We find that cumulative emissions attributable to upscaling low-carbon power other than hydropower are small compared with direct sectoral fossil fuel emissions and the total carbon budget. Fully considering life-cycle greenhouse gas emissions has only modest effects on the scale and structure of power production in cost-optimal mitigation scenarios.

Overview of the TriBITS Lifecycle Model: Lean/Agile Software Lifecycle Model for Research-based Computational Science and Engineering Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, Roscoe A; Heroux, Dr. Michael A; Willenbring, James

2012-01-01

Software lifecycles are becoming an increasingly important issue for computational science & engineering (CSE) software. The process by which a piece of CSE software begins life as a set of research requirements and then matures into a trusted high-quality capability is both commonplace and extremely challenging. Although an implicit lifecycle is obviously being used in any effort, the challenges of this process--respecting the competing needs of research vs. production--cannot be overstated. Here we describe a proposal for a well-defined software lifecycle process based on modern Lean/Agile software engineering principles. What we propose is appropriate for many CSE software projects thatmore » are initially heavily focused on research but also are expected to eventually produce usable high-quality capabilities. The model is related to TriBITS, a build, integration and testing system, which serves as a strong foundation for this lifecycle model, and aspects of this lifecycle model are ingrained in the TriBITS system. Indeed this lifecycle process, if followed, will enable large-scale sustainable integration of many complex CSE software efforts across several institutions.« less

A putative homologue of CDC20/CDH1 in the malaria parasite is essential for male gamete development.

PubMed

Guttery, David S; Ferguson, David J P; Poulin, Benoit; Xu, Zhengyao; Straschil, Ursula; Klop, Onny; Solyakov, Lev; Sandrini, Sara M; Brady, Declan; Nieduszynski, Conrad A; Janse, Chris J; Holder, Anthony A; Tobin, Andrew B; Tewari, Rita

2012-02-01

Cell-cycle progression is governed by a series of essential regulatory proteins. Two major regulators are cell-division cycle protein 20 (CDC20) and its homologue, CDC20 homologue 1 (CDH1), which activate the anaphase-promoting complex/cyclosome (APC/C) in mitosis, and facilitate degradation of mitotic APC/C substrates. The malaria parasite, Plasmodium, is a haploid organism which, during its life-cycle undergoes two stages of mitosis; one associated with asexual multiplication and the other with male gametogenesis. Cell-cycle regulation and DNA replication in Plasmodium was recently shown to be dependent on the activity of a number of protein kinases. However, the function of cell division cycle proteins that are also involved in this process, such as CDC20 and CDH1 is totally unknown. Here we examine the role of a putative CDC20/CDH1 in the rodent malaria Plasmodium berghei (Pb) using reverse genetics. Phylogenetic analysis identified a single putative Plasmodium CDC20/CDH1 homologue (termed CDC20 for simplicity) suggesting that Plasmodium APC/C has only one regulator. In our genetic approach to delete the endogenous cdc20 gene of P. berghei, we demonstrate that PbCDC20 plays a vital role in male gametogenesis, but is not essential for mitosis in the asexual blood stage. Furthermore, qRT-PCR analysis in parasite lines with deletions of two kinase genes involved in male sexual development (map2 and cdpk4), showed a significant increase in cdc20 transcription in activated gametocytes. DNA replication and ultra structural analyses of cdc20 and map2 mutants showed similar blockage of nuclear division at the nuclear spindle/kinetochore stage. CDC20 was phosphorylated in asexual and sexual stages, but the level of modification was higher in activated gametocytes and ookinetes. Changes in global protein phosphorylation patterns in the Δcdc20 mutant parasites were largely different from those observed in the Δmap2 mutant. This suggests that CDC20 and MAP2 are both likely to play independent but vital roles in male gametogenesis.

A Putative Homologue of CDC20/CDH1 in the Malaria Parasite Is Essential for Male Gamete Development

PubMed Central

Guttery, David S.; Ferguson, David J. P.; Poulin, Benoit; Xu, Zhengyao; Straschil, Ursula; Klop, Onny; Solyakov, Lev; Sandrini, Sara M.; Brady, Declan; Nieduszynski, Conrad A.; Janse, Chris J.; Holder, Anthony A.; Tobin, Andrew B.; Tewari, Rita

2012-01-01

Cell-cycle progression is governed by a series of essential regulatory proteins. Two major regulators are cell-division cycle protein 20 (CDC20) and its homologue, CDC20 homologue 1 (CDH1), which activate the anaphase-promoting complex/cyclosome (APC/C) in mitosis, and facilitate degradation of mitotic APC/C substrates. The malaria parasite, Plasmodium, is a haploid organism which, during its life-cycle undergoes two stages of mitosis; one associated with asexual multiplication and the other with male gametogenesis. Cell-cycle regulation and DNA replication in Plasmodium was recently shown to be dependent on the activity of a number of protein kinases. However, the function of cell division cycle proteins that are also involved in this process, such as CDC20 and CDH1 is totally unknown. Here we examine the role of a putative CDC20/CDH1 in the rodent malaria Plasmodium berghei (Pb) using reverse genetics. Phylogenetic analysis identified a single putative Plasmodium CDC20/CDH1 homologue (termed CDC20 for simplicity) suggesting that Plasmodium APC/C has only one regulator. In our genetic approach to delete the endogenous cdc20 gene of P. berghei, we demonstrate that PbCDC20 plays a vital role in male gametogenesis, but is not essential for mitosis in the asexual blood stage. Furthermore, qRT-PCR analysis in parasite lines with deletions of two kinase genes involved in male sexual development (map2 and cdpk4), showed a significant increase in cdc20 transcription in activated gametocytes. DNA replication and ultra structural analyses of cdc20 and map2 mutants showed similar blockage of nuclear division at the nuclear spindle/kinetochore stage. CDC20 was phosphorylated in asexual and sexual stages, but the level of modification was higher in activated gametocytes and ookinetes. Changes in global protein phosphorylation patterns in the Δcdc20 mutant parasites were largely different from those observed in the Δmap2 mutant. This suggests that CDC20 and MAP2 are both likely to play independent but vital roles in male gametogenesis. PMID:22383885

The influences of the recycle process on the bacterial community in a pilot scale microalgae raceway pond.

PubMed

Erkelens, Mason; Ball, Andrew S; Lewis, David M

2014-04-01

The use of recycled media has been shown to be a necessary step within the lifecycle of microalgal biofuels for economic sustainability and reducing the water footprint. However the impact of the harvesting of microalgae on the bacterial load of the recycled water has yet to be investigated. Within this study PCR-DGGE and real-time PCR was used to evaluate the bacterial community dynamics within the recycled water following harvest and concentration steps for a pilot scale open pond system (120,000L), which was developed for the production of green crude oil from Tetraselmis sp. in hyper saline water. Two stages were used in the harvesting; Stage 1 electroflocculation, and Stage 2 centrifugation. Electroflocculation was shown to have little effect on the bacterial cell concentration. In contrast bacterial diversity and cell concentration within the centrifugation step was greatly reduced. Copyright © 2014 Elsevier Ltd. All rights reserved.

Novel interactions between the HTLV antisense proteins HBZ and APH-2 and the NFAR protein family: Implications for the HTLV lifecycles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murphy, Jane; Hall, William W.; Ratner, Lee

The human T-cell leukaemia virus type 1 and type 2 (HTLV-1/HTLV-2) antisense proteins HBZ and APH-2 play key roles in the HTLV lifecycles and persistence in the host. Nuclear Factors Associated with double-stranded RNA (NFAR) proteins NF90/110 function in the lifecycles of several viruses and participate in host innate immunity against infection and oncogenesis. Using GST pulldown and co-immunoprecipitation assays we demonstrate specific novel interactions between HBZ/APH-2 and NF90/110 and characterised the protein domains involved. Moreover we show that NF90/110 significantly enhance Tax mediated LTR activation, an effect that was abolished by HBZ but enhanced by APH-2. Additionally we foundmore » that HBZ and APH-2 modulate the promoter activity of survivin and are capable of antagonising NF110-mediated survivin activation. Thus interactions between HTLV antisense proteins and the NFAR protein family have an overall positive impact on HTLV infection. Hence NFARs may represent potential therapeutic targets in HTLV infected cells. - Highlights: • This study demonstrates for the first time interactions between NF90/110 and the HTLV antisense proteins HBZ and APH-2. • We show that NF90/110 significantly enhance LTR activation by the HTLV Tax protein, an effect that is abolished by HBZ but enhanced by APH-2. • The study shows that even though the HTLV antisense proteins activate survivin expression they antagonize the ability of NF90/110 to do so. • Overall we found that NF90/110 positively regulate HTLV infection and as such might represent a therapeutic target in infected cells.« less

TriBITS lifecycle model. Version 1.0, a lean/agile software lifecycle model for research-based computational science and engineering and applied mathematical software.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willenbring, James M.; Bartlett, Roscoe Ainsworth; Heroux, Michael Allen

2012-01-01

Software lifecycles are becoming an increasingly important issue for computational science and engineering (CSE) software. The process by which a piece of CSE software begins life as a set of research requirements and then matures into a trusted high-quality capability is both commonplace and extremely challenging. Although an implicit lifecycle is obviously being used in any effort, the challenges of this process - respecting the competing needs of research vs. production - cannot be overstated. Here we describe a proposal for a well-defined software lifecycle process based on modern Lean/Agile software engineering principles. What we propose is appropriate for manymore » CSE software projects that are initially heavily focused on research but also are expected to eventually produce usable high-quality capabilities. The model is related to TriBITS, a build, integration and testing system, which serves as a strong foundation for this lifecycle model, and aspects of this lifecycle model are ingrained in the TriBITS system. Here, we advocate three to four phases or maturity levels that address the appropriate handling of many issues associated with the transition from research to production software. The goals of this lifecycle model are to better communicate maturity levels with customers and to help to identify and promote Software Engineering (SE) practices that will help to improve productivity and produce better software. An important collection of software in this domain is Trilinos, which is used as the motivation and the initial target for this lifecycle model. However, many other related and similar CSE (and non-CSE) software projects can also make good use of this lifecycle model, especially those that use the TriBITS system. Indeed this lifecycle process, if followed, will enable large-scale sustainable integration of many complex CSE software efforts across several institutions.« less

Converging on the optimal attainment of requirements

NASA Technical Reports Server (NTRS)

Feather, M. S.; Menzies, T.

2002-01-01

Planning for the optimal attainment of requirements is an important early lifecycle activity. However, such planning is difficult when dealing with competing requirements, limited resources, and the incompleteness of information available at requirements time.

SSMiles.

ERIC Educational Resources Information Center

Tracy, Dyanne M., Ed.

1993-01-01

Presents five integrated mathematics and science lessons in which students investigate the characteristics, behavior, lifecycles, and motion of mealworms and the feasibility of raising mealworms for profit. Purpose, time, materials needed, procedures, and extensions for each activity are provided. (MDH)

The evolutionary ecology of complex lifecycle parasites: linking phenomena with mechanisms

PubMed Central

Auld, S KJR; Tinsley, M C

2015-01-01

Many parasitic infections, including those of humans, are caused by complex lifecycle parasites (CLPs): parasites that sequentially infect different hosts over the course of their lifecycle. CLPs come from a wide range of taxonomic groups—from single-celled bacteria to multicellular flatworms—yet share many common features in their life histories. Theory tells us when CLPs should be favoured by selection, but more empirical studies are required in order to quantify the costs and benefits of having a complex lifecycle, especially in parasites that facultatively vary their lifecycle complexity. In this article, we identify ecological conditions that favour CLPs over their simple lifecycle counterparts and highlight how a complex lifecycle can alter transmission rate and trade-offs between growth and reproduction. We show that CLPs participate in dynamic host–parasite coevolution, as more mobile hosts can fuel CLP adaptation to less mobile hosts. Then, we argue that a more general understanding of the evolutionary ecology of CLPs is essential for the development of effective frameworks to manage the many diseases they cause. More research is needed identifying the genetics of infection mechanisms used by CLPs, particularly into the role of gene duplication and neofunctionalisation in lifecycle evolution. We propose that testing for signatures of selection in infection genes will reveal much about how and when complex lifecycles evolved, and will help quantify complex patterns of coevolution between CLPs and their various hosts. Finally, we emphasise four key areas where new research approaches will provide fertile opportunities to advance this field. PMID:25227255

Scheduling structural health monitoring activities for optimizing life-cycle costs and reliability of wind turbines

NASA Astrophysics Data System (ADS)

Hanish Nithin, Anu; Omenzetter, Piotr

2017-04-01

Optimization of the life-cycle costs and reliability of offshore wind turbines (OWTs) is an area of immense interest due to the widespread increase in wind power generation across the world. Most of the existing studies have used structural reliability and the Bayesian pre-posterior analysis for optimization. This paper proposes an extension to the previous approaches in a framework for probabilistic optimization of the total life-cycle costs and reliability of OWTs by combining the elements of structural reliability/risk analysis (SRA), the Bayesian pre-posterior analysis with optimization through a genetic algorithm (GA). The SRA techniques are adopted to compute the probabilities of damage occurrence and failure associated with the deterioration model. The probabilities are used in the decision tree and are updated using the Bayesian analysis. The output of this framework would determine the optimal structural health monitoring and maintenance schedules to be implemented during the life span of OWTs while maintaining a trade-off between the life-cycle costs and risk of the structural failure. Numerical illustrations with a generic deterioration model for one monitoring exercise in the life cycle of a system are demonstrated. Two case scenarios, namely to build initially an expensive and robust or a cheaper but more quickly deteriorating structures and to adopt expensive monitoring system, are presented to aid in the decision-making process.

Hot forming and quenching pilot process development for low cost and low environmental impact manufacturing.

NASA Astrophysics Data System (ADS)

Hall, Roger W.; Foster, Alistair; Herrmann Praturlon, Anja

2017-09-01

The Hot Forming and in-tool Quenching (HFQ®) process is a proven technique to enable complex shaped stampings to be manufactured from high strength aluminium. Its widespread uptake for high volume production will be maximised if it is able to wholly amortise the additional investment cost of this process compared to conventional deep drawing techniques. This paper discusses the use of three techniques to guide some of the development decisions taken during upscaling of the HFQ® process. Modelling of Process timing, Cost and Life-cycle impact were found to be effective tools to identify where development budget could be focused in order to be able to manufacture low cost panels of different sizes from many different alloys in a sustainable way. The results confirm that raw material cost, panel trimming, and artificial ageing were some of the highest contributing factors to final component cost. Additionally, heat treatment and lubricant removal stages played a significant role in the overall life-cycle assessment of the final products. These findings confirmed development priorities as novel furnace design, fast artificial ageing and low-cost alloy development.

Life-cycle assessment of municipal solid waste management alternatives with consideration of uncertainty: SIWMS development and application.

PubMed

Hanandeh, Ali El; El-Zein, Abbas

2010-05-01

This paper describes the development and application of the Stochastic Integrated Waste Management Simulator (SIWMS) model. SIWMS provides a detailed view of the environmental impacts and associated costs of municipal solid waste (MSW) management alternatives under conditions of uncertainty. The model follows a life-cycle inventory approach extended with compensatory systems to provide more equitable bases for comparing different alternatives. Economic performance is measured by the net present value. The model is verified against four publicly available models under deterministic conditions and then used to study the impact of uncertainty on Sydney's MSW management 'best practices'. Uncertainty has a significant effect on all impact categories. The greatest effect is observed in the global warming category where a reversal of impact direction is predicted. The reliability of the system is most sensitive to uncertainties in the waste processing and disposal. The results highlight the importance of incorporating uncertainty at all stages to better understand the behaviour of the MSW system. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

[The Role and Function of Informatics Nurses in Information Technology Decision-Making].

PubMed

Lee, Tso-Ying

2017-08-01

The medical environment has changed greatly with the coming of the information age, and, increasingly, the operating procedures for medical services have been altered in keeping with the trend toward mobile, paperless services. Informatization has the potential to improve the working efficiency of medical personnel, enhance patient care safety, and give medical organizations a positive image. Informatics nurses play an important role in the decision-making processes that accompany informatization. As one of the decision-making links in the information technology lifecycle, this role affects the success of the development and operation of information systems. The present paper examines the functions and professional knowledge that informatics nurses must possess during the technology lifecycle, the four stages of which include: planning, analysis, design/development/revision, and implementation/assessment/support/maintenance. The present paper further examines the decision-making shortcomings and errors that an informatics nurses may make during the decision-making process. We hope that this paper will serve as an effective and useful reference for informatics nurses during the informatization decision-making process.

Molecular analyses reveal high species diversity of trematodes in a sub-Arctic lake

USGS Publications Warehouse

Soldánová, Miroslava; Georgieva, Simona; Roháčováa, Jana; Knudsen, Rune; Kuhn, Jesper A.; Henriksen, Eirik H.; Siwertsson, Anna; Shaw, Jenny C.; Kuris, Armand M.; Amundsen, Per-Arne; Scholz, Tomáš; Lafferty, Kevin D.; Kostadinova, Aneta

2017-01-01

To identify trematode diversity and life-cycles in the sub-Arctic Lake Takvatn, Norway, we characterised 120 trematode isolates from mollusc first intermediate hosts, metacercariae from second intermediate host fishes and invertebrates, and adults from fish and invertebrate definitive hosts, using molecular techniques. Phylogenies based on nuclear and/or mtDNA revealed high species richness (24 species or species-level genetic lineages), and uncovered trematode diversity (16 putative new species) from five families typical in lake ecosystems (Allocreadiidae, Diplostomidae, Plagiorchiidae, Schistosomatidae and Strigeidae). Sampling potential invertebrate hosts allowed matching of sequence data for different stages, thus achieving molecular elucidation of trematode life-cycles and exploration of host-parasite interactions. Phylogenetic analyses also helped identify three major mollusc intermediate hosts (Radix balthica, Pisidium casertanum and Sphaerium sp.) in the lake. Our findings increase the known trematode diversity at the sub-Arctic Lake Takvatn, showing that digenean diversity is high in this otherwise depauperate sub-Arctic freshwater ecosystem, and indicating that sub-Arctic and Arctic ecosystems may be characterised by unique trematode assemblages.

Novel approaches to flavivirus drug discovery.

PubMed

Botting, Carolyn; Kuhn, Richard J

2012-05-01

The members of the family Flaviviridae, including West Nile virus, yellow fever virus and dengue virus, are important human pathogens that are expanding their impact around the globe. The four serotypes of dengue infect 50-100 million people each year, yet the only clinical treatment is supportive care to reduce symptoms. Drugs that employ novel inhibition mechanisms and targets are urgently needed to combat the growing incidence of dengue worldwide. The authors discuss recently discovered flavivirus inhibitors with a focus on antivirals targeting non-enzymatic proteins of the dengue virus lifecycle. Specifically, the authors discuss the flaviviruses, the need for novel inhibitors and the criteria for successful antiviral drug development. Current literature describing new advances in antiviral therapy at each stage of the flavivirus lifecycle (entry, endosomal escape, viral RNA processing and replication, assembly and immune evasion) are evaluated and summarized. Overall, the prognosis of flavivirus antiviral drug development is positive: new effective compounds have been discovered and studied. However, repurposing existing compounds and a greater translation to the clinical setting are recommended in order to combat the growing threat of flaviviruses.

The Development of using the digital projection method to measure the contact angle of ball screw

NASA Astrophysics Data System (ADS)

Chen, Chun-Jen; Jywe, Wenyuh; Liu, Yu-Chun; Jwo, Hsin-Hong

The ball screw frequently used to drive or translate the parts on the precision machine, such as machine tool and motorized stage. Therefore they were most frequently used on the precision machine, semiconductor equipment, medical instrument and aero industry. The main parts of ball screw are screw, ball and nut. The contact angle between the screw, ball and nut will affect the performance (include loading and noise) and lifecycle of a ball screw. If the actual contact angle and the designed contact angle are not the same, the friction between the ball, screw and nut will increase and it will result in the thermal increase and lifecycle decrease. This paper combines the traditional profile projector and commercial digital camera to build an imaging based and noncontact measurements system. It can implement the contact angle measurement quickly and accurately. Three different pitch angles of ball screws were completed tests in this paper. The angle resolution of this measurement system is about 0.001 degree and its accuracy is about 0.05 degree.

The circle of life: A cross-cultural comparison of children's attribution of life-cycle traits.

PubMed

Burdett, Emily R R; Barrett, Justin L

2016-06-01

Do children attribute mortality and other life-cycle traits to all minded beings? The present study examined whether culture influences young children's ability to conceptualize and differentiate human beings from supernatural beings (such as God) in terms of life-cycle traits. Three-to-5-year-old Israeli and British children were questioned whether their mother, a friend, and God would be subject to various life-cycle processes: Birth, death, ageing, existence/longevity, and parentage. Children did not anthropomorphize but differentiated among human and supernatural beings, attributing life-cycle traits to humans, but not to God. Although 3-year-olds differentiated significantly among agents, 5-year-olds attributed correct life-cycle traits more consistently than younger children. The results also indicated some cross-cultural variation in these attributions. Implications for biological conceptual development are discussed. © 2015 The British Psychological Society.

Idea Paper: The Lifecycle of Software for Scientific Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubey, Anshu; McInnes, Lois C.

The software lifecycle is a well researched topic that has produced many models to meet the needs of different types of software projects. However, one class of projects, software development for scientific computing, has received relatively little attention from lifecycle researchers. In particular, software for end-to-end computations for obtaining scientific results has received few lifecycle proposals and no formalization of a development model. An examination of development approaches employed by the teams implementing large multicomponent codes reveals a great deal of similarity in their strategies. This idea paper formalizes these related approaches into a lifecycle model for end-to-end scientific applicationmore » software, featuring loose coupling between submodels for development of infrastructure and scientific capability. We also invite input from stakeholders to converge on a model that captures the complexity of this development processes and provides needed lifecycle guidance to the scientific software community.« less

Study on Information Management for the Conservation of Traditional Chinese Architectural Heritage - 3d Modelling and Metadata Representation

NASA Astrophysics Data System (ADS)

Yen, Y. N.; Weng, K. H.; Huang, H. Y.

2013-07-01

After over 30 years of practise and development, Taiwan's architectural conservation field is moving rapidly into digitalization and its applications. Compared to modern buildings, traditional Chinese architecture has considerably more complex elements and forms. To document and digitize these unique heritages in their conservation lifecycle is a new and important issue. This article takes the caisson ceiling of the Taipei Confucius Temple, octagonal with 333 elements in 8 types, as a case study for digitization practise. The application of metadata representation and 3D modelling are the two key issues to discuss. Both Revit and SketchUp were appliedin this research to compare its effectiveness to metadata representation. Due to limitation of the Revit database, the final 3D models wasbuilt with SketchUp. The research found that, firstly, cultural heritage databasesmustconvey that while many elements are similar in appearance, they are unique in value; although 3D simulations help the general understanding of architectural heritage, software such as Revit and SketchUp, at this stage, could onlybe used tomodel basic visual representations, and is ineffective indocumenting additional critical data ofindividually unique elements. Secondly, when establishing conservation lifecycle information for application in management systems, a full and detailed presentation of the metadata must also be implemented; the existing applications of BIM in managing conservation lifecycles are still insufficient. Results of the research recommends SketchUp as a tool for present modelling needs, and BIM for sharing data between users, but the implementation of metadata representation is of the utmost importance.

A major cathepsin B protease from the liver fluke Fasciola hepatica has atypical active site features and a potential role in the digestive tract of newly excysted juvenile parasites

PubMed Central

Beckham, Simone A.; Piedrafita, David; Phillips, Carolyn I.; Samarawickrema, Nirma; Law, Ruby H.P.; Smooker, Peter M.; Quinsey, Noelene S.; Irving, James A.; Greenwood, Deanne; Verhelst, Steven H. L.; Bogyo, Matthew; Turk, Boris; Coetzer, Theresa H.; Wijeyewickrema, Lakshmi C.; Spithill, Terry W.; Pike, Robert N.

2012-01-01

The newly excysted juvenile (NEJ) stage of the Fasciola hepatica lifecycle occurs just prior to invasion into the wall of the gut of the host, rendering it an important target for drug development. The cathepsin B enzymes from NEJ flukes have recently been demonstrated to be crucial to invasion and migration by the parasite. Here we characterize one of the cathepsin B enzymes (recombinant FhcatB1) from NEJ flukes. FhcatB1 has biochemical properties distinct from mammalian cathepsin B enzymes, with an atypical preference for Ile over Leu or Arg residues at the P2 substrate position and an inability to act as an exopeptidase. FhcatB1 was active across a broad pH range (optimal activity at pH 5.5–7.0) and resistant to inhibition by cystatin family inhibitors from sheep and humans, suggesting that this enzyme would be able to function in extracellular environments in its mammalian hosts. It appears, however, that the FhcatB1 protease functions largely as a digestive enzyme in the gut of the parasite, due to the localization of a specific, fluorescently labeled inhibitor with an Ile at the P2 position. Molecular modelling and dynamics were used to predict the basis for the unusual substrate specificity: a P2 Ile residue positions the substrate optimally for interaction with catalytic residues of the enzyme, and the enzyme lacks an occluding loop His residue crucial for exopeptidase activity. The unique features of the enzyme, particularly with regard to its specificity and likely importance to a vital stage of the parasite’s life cycle, make it an excellent target for therapeutic inhibitors or vaccination. PMID:19401154

Materials Lifecycle and Environmental Consideration at NASA

NASA Technical Reports Server (NTRS)

Clark-Ingram, Marceia

2010-01-01

The aerospace community faces tremendous challenges with continued availability of existing material supply chains during the lifecycle of a program. Many obsolescence drivers affect the availability of materials: environmental safety ahd health regulations, vendor and supply economics, market sector demands,and natural disasters. Materials selection has become increasingly more critical when designing aerospace hardware. NASA and DoD conducted a workshop with subject matter experts to discuss issues and define solutions for materials selections during the lifecycle phases of a product/system/component. The three primary lifecycle phases were: Conceptualization/Design, Production & Sustainment, and End of life / Reclamation. Materials obsolescence and pollution prevention considerations were explored for the aforementioned lifecycle phases. The recommended solutions from the workshop are being presented.

Multiscale design and life-cycle based sustainability assessment of polymer nanocomposite coatings

NASA Astrophysics Data System (ADS)

Uttarwar, Rohan G.

In recent years, nanocoatings with exceptionally improved and new performance properties have found numerous applications in the automotive, aerospace, ship-making, chemical, electronics, steel, construction, and many other industries. Especially the formulations providing multiple functionalities to cured paint films are believed to dominate the coatings market in the near future. It has shifted the focus of research towards building sustainable coating recipes which can deliver multiple functionalities through applied films. The challenge to this exciting area of research arrives from the insufficient knowledge about structure-property correlations of nanocoating materials and their design complexity. Experimental efforts have been successful in developing certain types of nanopaints exhibiting improved properties. However, multifunctional nanopaint design optimality is extremely difficult to address if not impossible solely through experiments. In addition to this, the environmental implications and societal risks associated with this growing field of nanotechnology raise several questions related to its sustainable development. This research focuses on the study of a multiscale sustainable nanocoating design which can have the application from novel function envisioning and idea refinement point of view, to knowledge discovery and design solution derivation, and further to performance testing in industrial applications. The nanocoating design is studied using computational simulations of nano- to macro- scale models and sustainability assessment study over the life-cycle. Computational simulations aim at integrating top-down, goals/means, inductive systems engineering and bottom-up, cause and effect, deductive systems engineering approaches for material development. The in-silico paint resin system is a water-dispersible acrylic polymer with hydrophilic nanoparticles incorporated into it. The nano-scale atomistic and micro-scale coarse-grained (CG) level simulations are performed using molecular dynamics methodology to study several structural and morphological features such as effect of polymer molecular weight, polydispersity, rheology, nanoparticle volume fraction, size, shape and chemical nature on the bulk mechanical and self-cleaning properties of the coating film. At macro-scale, a paint spray system which is used for automotive coating application is studied by using CFD-based simulation methodology to generate crucial information about the effects of nanocoating technology on environmental emissions and coating film quality. The cradle-to-grave life-cycle based sustainability assessment study address all the critical issues related to economic benefits, environmental implications and societal effects of nanocoating technology through case studies of automotive coating systems. It is accomplished by identifying crucial correlations among measurable parameters at different stages and developing sustainability indicator matrices for analysis of each stage of life-cycle. The findings from the research can have great potential to draft useful conclusions in favor of future development of coating systems with novel functionalities and improved sustainability.

A Two-Stage-to-Orbit Spaceplane Concept With Growth Potential

NASA Technical Reports Server (NTRS)

Mehta, Unmeel B.; Bowles, Jeffrey V.

2001-01-01

A two-stage-to-orbit (TSTO) spaceplane concept developed in 1993 is revisited, and new information is provided to assist in the development of the next-generation space transportation vehicles. The design philosophy, TSTO spaceplane concept, and the design method are briefly described. A trade study between cold and hot structures leads to the choice of cold structures with external thermal protection systems. The optimal Mach number for staging the second stage of the TSTO spaceplane (with air-breathing propulsion on the first stage) is 10, based on life-cycle cost analysis. The performance and specification of a prototype/experimental (P/X) TSTO spaceplane with a turbo/ram/scramjet propulsion system and built-in growth potential are presented and discussed. The internal rate of return on investment is the highest for the proposed TSTO spaceplane, vis-A-vis a single-stage-to-orbit (SSTO) rocket vehicle and a TSTO spaceplane without built-in growth. Additional growth potentials for the proposed spaceplane are suggested. This spaceplane can substantially decrease access-to-space cost and risk, and increase safety and reliability in the near term It can be a serious candidate for the next-generation space transportation system.

Building Maintenance and Repair Data for Life-Cycle Cost Analyses: Electrical Systems.

DTIC Science & Technology

1991-05-01

Repair Data for Life-Cycle Cost Analyses: Electrical Systems by Edgar S. Neely Robert D. Neathammer James R. Stirn Robert P. Winkler This research...systems have been developed to assist planners in preparing DD Form 1391 documentation, designers in life-cycle cost component selection, and maintainers...Maintenance and Repair Data for Life-Cycle Cost Analyses: RDTE dated 1980 Electrical Systems REIMB 1984 - 1989 6. AUTH4OR(S) Edgar S. Neely, Robert D

Real options and asset valuation in competitive energy markets

NASA Astrophysics Data System (ADS)

Oduntan, Adekunle Richard

The focus of this work is to develop a robust valuation framework for physical power assets operating in competitive markets such as peaking or mid-merit thermal power plants and baseload power plants. The goal is to develop a modeling framework that can be adapted to different energy assets with different types of operating flexibilities and technical constraints and which can be employed for various purposes such as capital budgeting, business planning, risk management and strategic bidding planning among others. The valuation framework must also be able to capture the reality of power market rules and opportunities, as well as technical constraints of different assets. The modeling framework developed conceptualizes operating flexibilities of power assets as "switching options' whereby the asset operator decides at every decision point whether to switch from one operating mode to another mutually exclusive mode, within the limits of the equipment constraints of the asset. As a current decision to switch operating modes may affect future operating flexibilities of the asset and hence cash flows, a dynamic optimization framework is employed. The developed framework accounts for the uncertain nature of key value drivers by representing them with appropriate stochastic processes. Specifically, the framework developed conceptualizes the operation of a power asset as a multi-stage decision making problem where the operator has to make a decision at every stage to alter operating mode given currently available information about key value drivers. The problem is then solved dynamically by decomposing it into a series of two-stage sub-problems according to Bellman's optimality principle. The solution algorithm employed is the Least Squares Monte Carlo (LSM) method. The developed valuation framework was adapted for a gas-fired thermal power plant, a peaking hydroelectric power plant and a baseload power plant. This work built on previously published real options valuation methodologies for gas-fired thermal power plants by factoring in uncertainty from gas supply/consumption imbalance which is usually faced by gas-fired power generators. This source of uncertainty arises because of mismatch between natural gas and electricity wholesale markets. Natural gas markets in North America operate on a day-ahead basis while power plants are dispatched in real time. Inability of a power generator to match its gas supply and consumption in real time, leading to unauthorized gas over-run or under-run, attracts penalty charges from the gas supplier to the extent that the generator can not manage the imbalance through other means. By considering an illustrative power plant operating in Ontario, we show effects of gas-imbalance on dispatch strategies on a daily cycling operation basis and the resulting impact on net revenue. Similarly, we employ the developed valuation framework to value a peaking hydroelectric power plant. This application also builds on previous real options valuation work for peaking hydroelectric power plants by considering their operations in a joint energy and ancillary services market. Specifically, the valuation model is developed to capture the value of a peaking power plant whose owner has the flexibility to participate in a joint operating reserve market and an energy market, which is currently the case in the Ontario wholesale power market. The model factors in water inflow uncertainty into the reservoir forebay of a hydroelectric facility and also considers uncertain energy and operating reserve prices. The switching options considered include (i) a joint energy and operating reserve bid (ii) an energy only bid and (iii) a do nothing (idle) strategy. Being an energy limited power plant, by doing nothing at a decision interval, the power asset operator is able to timeshift scarce water for use at a future period when market situations are expected to be better. Finally, the developed valuation framework was employed to optimize life-cycle management decisions of a baseload power plant, such as a nuclear power plant. Given uncertainty of long-term value drivers, including power prices, equipment performance and the relationship between current life cycle spending and future equipment degradation, optimization is carried out with the objective of minimizing overall life-cycle related costs. These life-cycle costs include (i) lost revenue during planned and unplanned outages, (ii) potential costs of future equipment degradation due to inadequate preventative maintenance, and (iii) the direct costs of implementing the life-cycle projects. The switching options in this context include the option to shutdown the power plant in order to execute a given preventative maintenance and inspection project and the option to keep the option "alive" by choosing to delay a planned life-cycle activity.

Bus Lifecycle Cost Model for Federal Land Management Agencies.

DOT National Transportation Integrated Search

2011-09-30

The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

A 20 Year Lifecycle Study for Launch Facilities at the Kennedy Space Center

NASA Technical Reports Server (NTRS)

Kolody, Mark R.; Li. Wenyan; Hintze, Paul E.; Calle, Luz-Marina

2009-01-01

The lifecycle cost analysis was based on corrosion costs for the Kennedy Space Center's Launch Complexes and Mobile Launch Platforms. The first step in the study involved identifying the relevant assets that would be included. Secondly, the identification and collection of the corrosion control cost data for the selected assets was completed. Corrosion control costs were separated into four categories. The sources of cost included the NASA labor for civil servant personnel directly involved in overseeing and managing corrosion control of the assets, United Space Alliance (USA) contractual requirements for performing planned corrosion control tasks, USA performance of unplanned corrosion control tasks, and Testing and Development. Corrosion control operations performed under USA contractual requirements were the most significant contributors to the total cost of corrosion. The operations include the inspection of the pad, routine maintenance of the pad, medium and large scale blasting and repainting activities, and the repair and replacement of structural metal elements. Cost data was collected from the years between 2001 and 2007. These costs were then extrapolated to future years to calculate the 20 year lifecycle costs.

The use of advanced mass spectrometry to dissect the life-cycle of photosystem II

DOE PAGES

Weisz, Daniel A.; Gross, Michael L.; Pakrasi, Himadri B.

2016-05-10

Photosystem II (PSII) is a photosynthetic membrane-protein complex that undergoes an intricate, tightly regulated cycle of assembly, damage, and repair. The available crystal structures of cyanobacterial PSII are an essential foundation for understanding PSII function, but nonetheless provide a snapshot only of the active complex. To study aspects of the entire PSII life-cycle, mass spectrometry (MS) has emerged as a powerful tool that can be used in conjunction with biochemical techniques. In this article, we present the MS-based approaches that are used to study PSII composition, dynamics, and structure, and review the information about the PSII life-cycle that has beenmore » gained by these methods. This information includes the composition of PSII subcomplexes, discovery of accessory PSII proteins, identification of post-translational modifications and quantification of their changes under various conditions, determination of the binding site of proteins not observed in PSII crystal structures, conformational changes that underlie PSII functions, and identification of water and oxygen channels within PSII. Lastly, we conclude with an outlook for the opportunity of future MS contributions to PSII research.« less

An atypical proprotein convertase in Giardia lamblia differentiation.

PubMed

Davids, B J; Gilbert, M A; Liu, Q; Reiner, D S; Smith, A J; Lauwaet, T; Lee, C; McArthur, A G; Gillin, F D

2011-02-01

Proteolytic activity is important in the lifecycles of parasites and their interactions with hosts. Cysteine proteases have been best studied in Giardia, but other protease classes have been implicated in growth and/or differentiation. In this study, we employed bioinformatics to reveal the complete set of putative proteases in the Giardia genome. We identified 73 peptidase homologs distributed over 5 catalytic classes in the genome. Serial analysis of gene expression of the G. lamblia lifecycle found thirteen protease genes with significant transcriptional variation over the lifecycle, with only one serine protease transcript upregulated late in encystation. The translated gene sequence of this encystation-specific transcript was most similar to eukaryotic subtilisin-like proprotein convertases (SPC), although the typical catalytic triad was not identified. Epitope-tagged gSPC protein expressed in Giardia under its own promoter was upregulated during encystation with highest expression in cysts and it localized to encystation-specific secretory vesicles (ESV). Total gSPC from encysting cells produced proteolysis in gelatin gels that co-migrated with the epitope-tagged protease in immunoblots. Immuno-purified gSPC also had gelatinase activity. To test whether endogenous gSPC activity is involved in differentiation, trophozoites and cysts were exposed to the specific serine proteinase inhibitor 4-(2-aminoethyl)-benzenesulfonyl fluoride hydrochloride (AEBSF). After 21 h encystation, a significant decrease in ESV was observed with 1mM AEBSF and by 42 h the number of cysts was significantly reduced, but trophozoite growth was not inhibited. Concurrently, levels of cyst wall proteins 1 and 2, and AU1-tagged gSPC protein itself were decreased. Excystation of G. muris cysts was also significantly reduced in the presence of AEBSF. These results support the idea that serine protease activity is essential for Giardia encystation and excystation. Copyright © 2010 Elsevier B.V. All rights reserved.

An Atypical Proprotein Convertase in Giardia lamblia Differentiation

PubMed Central

Davids, B. J.; Gilbert, M. A.; Liu, Q.; Reiner, D. S.; Smith, A. J.; Lauwaet, T.; Lee, C.; McArthur, A. G.; Gillin, F. D.

2010-01-01

Proteolytic activity is important in the lifecycles of parasites and their interactions with hosts. Cysteine proteases have been best studied in Giardia, but other protease classes have been implicated in growth and/or differentiation. In this study, we employed bioinformatics to reveal the complete set of putative proteases in the Giardia genome. We identified 73 peptidase homologues distributed over 5 catalytic classes in the genome. Serial analysis of gene expression of the G. lamblia lifecycle found thirteen protease genes with significant transcriptional variation over the lifecycle, with only one serine protease transcript upregulated late in encystation. The translated gene sequence of this encystation-specific transcript was most similar to eukaryotic subtilisin-like proprotein convertases (SPC), although the typical catalytic triad was not identified. Epitope-tagged gSPC protein expressed in Giardia under its own promoter was upregulated during encystation with highest expression in cysts and it localized to encystation-specific secretory vesicles (ESV). Total gSPC from encysting cells produced proteolysis in gelatin gels that co-migrated with the epitope-tagged protease in immunoblots. Immuno-purified gSPC also had gelatinase activity. To test whether endogenous gSPC activity is involved in differentiation, trophozoites and cysts were exposed to the specific serine proteinase inhibitor 4-(2-Aminoethyl)-benzenesulfonyl fluoride hydrochloride (AEBSF). After 21 h encystation, a significant decrease in ESV was observed with 1 mM AEBSF and by 42 h the number of cysts was significantly reduced, but trophozoite growth was not inhibited. Concurrently, levels of cyst wall proteins 1 and 2, and AU1-tagged gSPC protein itself were decreased. Excystation of G. muris cysts was also significantly reduced in the presence of AEBSF. These results support the idea that serine protease activity is essential for Giardia encystation and excystation. PMID:21075147

Depsides: Lichen Metabolites Active against Hepatitis C Virus

PubMed Central

Vu, Thi Huyen; Le Lamer, Anne-Cécile; Lalli, Claudia; Boustie, Joël; Samson, Michel

2015-01-01

A thorough phytochemical study of Stereocaulon evolutum was conducted, for the isolation of structurally related atranorin derivatives. Indeed, pilot experiments suggested that atranorin (1), the main metabolite of this lichen, would interfere with the lifecycle of hepatitis C virus (HCV). Eight compounds, including one reported for the first time (2), were isolated and characterized. Two analogs (5, 6) were also synthesized, to enlarge the panel of atranorin-related structures. Most of these compounds were active against HCV, with a half-maximal inhibitory concentration of about 10 to 70 µM, with depsides more potent than monoaromatic phenols. The most effective inhibitors (1, 5 and 6) were then added at different steps of the HCV lifecycle. Interestingly, atranorin (1), bearing an aldehyde function at C-3, inhibited only viral entry, whereas the synthetic compounds 5 and 6, bearing a hydroxymethyl and a methyl function, respectively, at C-3 interfered with viral replication. PMID:25793970

Strategic balance of drug lifecycle management options differs between domestic and foreign companies in Japan.

PubMed

Yamanaka, Takayuki; Kano, Shingo

2016-01-01

Drug approvals and patent protections are critical in drug lifecycle management (LCM) in order to maximize drug discovery investment returns. We analyzed drug LCM activities implemented by 10 top companies in Japan, focusing on drug approvals and patent term extensions. Foreign companies acquired numerous drug approvals primarily for new molecular entities (NMEs), while Japanese companies mainly obtained approvals for improved drugs including new indications, and intensively extended patent terms. Furthermore, we discovered three factors likely responsible for differences in drug LCM strategies of Japanese and foreign companies: research and development capacities for drugs, drug lags of foreign-origin NMEs, and cooperation between Research and Development Departments and Intellectual Property Departments.

Select pyrimidinones inhibit the propagation of the malarial parasite, Plasmodium falciparum

PubMed Central

Chiang, Annette N.; Valderramos, Juan-Carlos; Balachandran, Raghavan; Chovatiya, Raj J.; Mead, Brian P.; Schneider, Corinne; Bell, Samantha L.; Klein, Michael G.; Huryn, Donna M.; Chen, Xiaojiang S.; Day, Billy W.; Fidock, David A.; Wipf, Peter; Brodsky, Jeffrey L.

2009-01-01

Plasmodium falciparum, the Apicomplexan parasite that is responsible for the most lethal forms of human malaria, is exposed to radically different environments and stress factors during its complex lifecycle. In any organism, Hsp70 chaperones are typically associated with tolerance to stress. We therefore reasoned that inhibition of P. falciparum Hsp70 chaperones would adversely affect parasite homeostasis. To test this hypothesis, we measured whether pyrimidinone-amides, a new class of Hsp70 modulators, could inhibit the replication of the pathogenic P. falciparum stages in human red blood cells. Nine compounds with IC50 values from 30 nM to 1.6 μM were identified. Each compound also altered the ATPase activity of purified P. falciparum Hsp70 in single-turnover assays, although higher concentrations of agents were required than was necessary to inhibit P. falciparum replication. Varying effects of these compounds on Hsp70s from other organisms were also observed. Together, our data indicate that pyrimidinone-amides constitute a novel class of anti-malarial agents. PMID:19195901

Fate-Regulating Circuits in Viruses: From Discovery to New Therapy Targets

PubMed Central

Pai, Anand; Weinberger, Leor S.

2018-01-01

Current antivirals effectively target diverse viruses at various stages of their viral lifecycles. Nevertheless, curative therapy has remained elusive for important pathogens (e.g., HIV-1 and herpesviruses), in large part due to viral latency and the evolution of resistance to existing therapies. Here, we review the discovery of viral ‘master’ circuits: virus-encoded auto-regulatory gene networks that can autonomously control viral expression programs (i.e., between active, latent, and abortive fates). These circuits offer a potential new class of antivirals that could lead to intrinsic combination-antiviral therapies within a single molecule—evolutionary escape from such circuit ‘disruptors’ would require simultaneous evolution of both the cis regulatory element (e.g., the DNA-binding site) and the trans element (e.g., the transcription factor) for the circuit’s function to be recapitulated. We review the architectures of these fate-regulating master circuits in HIV-1 and the human herpesvirus cytomegalovirus (CMV) along with potential circuit-disruption strategies that may ultimately enable escape-resistant antiviral therapies. PMID:28800289

An exchange format for use-cases of hospital information systems.

PubMed

Masuda, G; Sakamoto, N; Sakai, R; Yamamoto, R

2001-01-01

Object-oriented software development is a powerful methodology for development of large hospital information systems. We think use-case driven approach is particularly useful for the development. In the use-cases driven approach, use-cases are documented at the first stage in the software development process and they are used through the whole steps in a variety of ways. Therefore, it is important to exchange and share the use-cases and make effective use of them through the overall lifecycle of a development process. In this paper, we propose a method of sharing and exchanging use-case models between applications, developers, and projects. We design an XML based exchange format for use-cases. We then discuss an application of the exchange format to support several software development activities. We preliminarily implemented a support system for object-oriented analysis based on the exchange format. The result shows that using the structural and semantic information in the exchange format enables the support system to assist the object-oriented analysis successfully.

Information system life-cycle and documentation standards, volume 1

NASA Technical Reports Server (NTRS)

Callender, E. David; Steinbacher, Jody

1989-01-01

The Software Management and Assurance Program (SMAP) Information System Life-Cycle and Documentation Standards Document describes the Version 4 standard information system life-cycle in terms of processes, products, and reviews. The description of the products includes detailed documentation standards. The standards in this document set can be applied to the life-cycle, i.e., to each phase in the system's development, and to the documentation of all NASA information systems. This provides consistency across the agency as well as visibility into the completeness of the information recorded. An information system is software-intensive, but consists of any combination of software, hardware, and operational procedures required to process, store, or transmit data. This document defines a standard life-cycle model and content for associated documentation.

Reducing Life-Cycle Costs.

ERIC Educational Resources Information Center

Roodvoets, David L.

2003-01-01

Presents factors to consider when determining roofing life-cycle costs, explaining that costs do not tell the whole story; discussing components that should go into the decision (cost, maintenance, energy use, and environmental costs); and concluding that important elements in reducing life-cycle costs include energy savings through increased…

From the Cradle to the Grave.

ERIC Educational Resources Information Center

Hill, Jim, Ed.

1994-01-01

Examines the emerging discipline known as life-cycle assessment (LCA) used to evaluate the true environmental impacts of products, materials, or activities from the time raw materials leave the earth until those materials return to their final resting place. (LZ)

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE BGU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyrotechnic (PEP) materials of interest to the U.S. Department of Defense (DoD)...

Model-based optimal design of active cool thermal energy storage for maximal life-cycle cost saving from demand management in commercial buildings

DOE PAGES

Cui, Borui; Gao, Dian-ce; Xiao, Fu; ...

2016-12-23

This article provides a method in comprehensive evaluation of cost-saving potential of active cool thermal energy storage (CTES) integrated with HVAC system for demand management in non-residential building. The active storage is beneficial by shifting peak demand for peak load management (PLM) as well as providing longer duration and larger capacity of demand response (DR). In this research, a model-based optimal design method using genetic algorithm is developed to optimize the capacity of active CTES aiming for maximizing the life-cycle cost saving concerning capital cost associated with storage capacity as well as incentives from both fast DR and PLM. Inmore » the method, the active CTES operates under a fast DR control strategy during DR events while under the storage-priority operation mode to shift peak demand during normal days. The optimal storage capacities, maximum annual net cost saving and corresponding power reduction set-points during DR event are obtained by using the proposed optimal design method. Lastly, this research provides guidance in comprehensive evaluation of cost-saving potential of CTES integrated with HVAC system for building demand management including both fast DR and PLM.« less

Model-based optimal design of active cool thermal energy storage for maximal life-cycle cost saving from demand management in commercial buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Borui; Gao, Dian-ce; Xiao, Fu

This article provides a method in comprehensive evaluation of cost-saving potential of active cool thermal energy storage (CTES) integrated with HVAC system for demand management in non-residential building. The active storage is beneficial by shifting peak demand for peak load management (PLM) as well as providing longer duration and larger capacity of demand response (DR). In this research, a model-based optimal design method using genetic algorithm is developed to optimize the capacity of active CTES aiming for maximizing the life-cycle cost saving concerning capital cost associated with storage capacity as well as incentives from both fast DR and PLM. Inmore » the method, the active CTES operates under a fast DR control strategy during DR events while under the storage-priority operation mode to shift peak demand during normal days. The optimal storage capacities, maximum annual net cost saving and corresponding power reduction set-points during DR event are obtained by using the proposed optimal design method. Lastly, this research provides guidance in comprehensive evaluation of cost-saving potential of CTES integrated with HVAC system for building demand management including both fast DR and PLM.« less

Lifecycle greenhouse gas emissions of coal, conventional and unconventional natural gas for electricity generation

EPA Science Inventory

An analysis of the lifecycle greenhouse gas (GHG) emissions associated with natural gas use recently published by Howarth et al. (2011) stated that use of natural gas produced from shale formations via hydraulic fracturing would generate greater lifecycle GHG emissions than petro...

LIFE-CYCLE IMPACT ASSESSMENT DEMONSTRATION FOR THE GBU-24

EPA Science Inventory

The primary goal of this project was to develop and demonstrate a life-cycle impact assessment (LCIA) approach using existing life-cycle inventory (LCI) data on one of the propellants, energetics, and pyro-technic (PEP) materials of interest to the U.S. Department of Defense (DoD...

Life-cycle energy and emissions inventories for motorcycles, diesel automobiles, school buses, electric buses, Chicago rail, and New York City rail

DOT National Transportation Integrated Search

2009-05-01

The development of life-cycle energy and emissions factors for passenger transportation modes : is critical for understanding the total environmental costs of travel. Previous life-cycle studies : have focused on the automobile given its dominating s...

Enterprise Information Lifecycle Management

DTIC Science & Technology

2011-01-01

Public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing...regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to Washington...Need for Information Lifecycle Management .......................................................... 6 3.3 Challenges of Information Lifecycle

Knowledge based system verification and validation as related to automation of space station subsystems: Rationale for a knowledge based system lifecycle

NASA Technical Reports Server (NTRS)

Richardson, Keith; Wong, Carla

1988-01-01

The role of verification and validation (V and V) in software has been to support and strengthen the software lifecycle and to ensure that the resultant code meets the standards of the requirements documents. Knowledge Based System (KBS) V and V should serve the same role, but the KBS lifecycle is ill-defined. The rationale of a simple form of the KBS lifecycle is presented, including accommodation to certain critical KBS differences from software development.

Psychological drivers in doping: The life-cycle model of performance enhancement

PubMed Central

Petróczi, Andrea; Aidman, Eugene

2008-01-01

Background Performance enhancement (PE) is a natural and essential ingredient of competitive sport. Except for nutritional supplement contamination, accidental use of doping is highly unlikely. It requires deliberation, planning and commitment; and is influenced by a host of protective and risk factors. Hypothesis In the course of their career, athletes constantly set goals and make choices regarding the way these goals can be achieved. The cycle of choice – goal commitment – execution – feedback on goal attainment – goal evaluation/adjustment has numerous exit points, each providing an opportunity for behaviour change, which may or may not be related to the use of prohibited methods. The interplay between facilitating and inhibiting systemic and personality factors, constantly influenced by situational factors could result in an outcome vector of 'doping attitudes', which combines with subjective norms to influence intentions to choose prohibited PE methods. These influences also vary from one stage of athlete development to the next, making some athletes more vulnerable to engaging in doping practices than others, and more vulnerable at certain time periods – and not others. Testing the hypothesis Model-testing requires a series of carefully planned and coordinated studies. Correlational studies can establish relationships where the directionality is not-known or not important. Experimental studies with the manipulation of doping expectancies and risk factors can be used to demonstrate causality and evaluate potential intervention strategies. The final model can be tested via a behavioural simulation, with outcomes compared to those expected from literature precedence or used as a simulated computer game for empirical data collection. Implications A hypothesized life-cycle model of PE identifies vulnerability factors across the stages of athlete development with the view of informing the design of anti-doping assessment and intervention. The model suggests that, instead of focusing on the actual engagement in prohibited PE practices, deterrence strategies are likely to be more effective if they target the influencing factors at the appropriate stage and identify groups of athletes and their respective career stages, which pose particular risks of engagement in doping practices. This enables a more effective intervention approach by targeting specific risk factors and expectancies. PMID:18331645

Development of a conceptual framework of holistic risk assessment - Landfill as a particular type of contaminated land.

PubMed

Butt, T E; Javadi, A A; Nunns, M A; Beal, C D

2016-11-01

Landfills can be regarded as a particular type of contaminated land that has a potential to directly and indirectly pollute all of the four main spheres of the environment which are the lithosphere, atmosphere, hydrosphere and eventually adversely impact the biosphere. Therefore, environmental risk assessment of a landfill has to be more integrated and holistic by virtue of its nature of being a multidimensional pollutant source. Despite this, although various risk assessment approaches have been adopted for landfill waste disposal sites, there are still wide-ranging knowledge gaps and limitations which need to be addressed. One important knowledge gap and limitation of current risk assessment approaches is the inability to fully identify, categorise and aggregate all individual risks from all combinations of hazards, pathways and targets/receptors (e.g. water, air, soil and biota) in connection to a certain landfill leachate and yet at any stage of the landfill cycle. So such an approach is required that could not only integrate all possible characteristics of varying scenarios but also contain the ability to establish an overall risk picture, irrespective of the lifecycle stage of the landfill (e.g. planning stage/pre-operation, in-operation or post-operation/closed). One such approach to address the wide-breadth of landfill impact risks is by developing a more holistic risk assessment methodology, whose conceptual framework is presented in this paper for landfill leachate in a whole-system format. This conceptual framework does not only draw together various constituting factors and sub-factors of risk assessment in a logical sequence and categorical order, but also indicates the "what, why, when and how" outputs of and inputs to these factors and sub-factors can be useful. The framework is designed to identify and quantify a range of risks associated with all stages of the landfill lifecycle, and yet in a more streamlined, logical, categorical and integrated format, offering a more standardised and unified whole-system approach. Copyright © 2016. Published by Elsevier B.V.

Analysis of the Lifecycle of Mechanical Engineering Products

NASA Astrophysics Data System (ADS)

Gubaydulina, R. H.; Gruby, S. V.; Davlatov, G. D.

2016-08-01

Principal phases of the lifecycle of mechanical engineering products are analyzed in the paper. The authors have developed methods and procedures to improve designing, manufacturing, operating and recycling of the machine. It has been revealed that economic lifecycle of the product is a base for appropriate organization of mechanical engineering production. This lifecycle is calculated as a minimal sum total of consumer and producer costs. The machine construction and its manufacturing technology are interrelated through a maximal possible company profit. The products are to be recycled by their producer. Recycling should be considered as a feedback phase, necessary to make the whole lifecycle of the product a constantly functioning self-organizing system. The principles, outlined in this paper can be used as fundamentals to develop an automated PLM-system.

Evaluation of life-cycle air emission factors of freight transportation.

PubMed

Facanha, Cristiano; Horvath, Arpad

2007-10-15

Life-cycle air emission factors associated with road, rail, and air transportation of freight in the United States are analyzed. All life-cycle phases of vehicles, infrastructure, and fuels are accounted for in a hybrid life-cycle assessment (LCA). It includes not only fuel combustion, but also emissions from vehicle manufacturing, maintenance, and end of life, infrastructure construction, operation, maintenance, and end of life, and petroleum exploration, refining, and fuel distribution. Results indicate that total life-cycle emissions of freight transportation modes are underestimated if only tailpipe emissions are accounted for. In the case of CO2 and NOx, tailpipe emissions underestimate total emissions by up to 38%, depending on the mode. Total life-cycle emissions of CO and SO2 are up to seven times higher than tailpipe emissions. Sensitivity analysis considers the effects of vehicle type, geography, and mode efficiency on the final results. Policy implications of this analysis are also discussed. For example, while it is widely assumed that currently proposed regulations will result in substantial reductions in emissions, we find that this is true for NOx, emissions, because fuel combustion is the main cause, and to a lesser extent for SO2, but not for PM10 emissions, which are significantly affected by the other life-cycle phases.

Flowering Locus C (FLC) Is a Potential Major Regulator of Glucosinolate Content across Developmental Stages of Aethionema arabicum (Brassicaceae)

PubMed Central

Mohammadin, Setareh; Nguyen, Thu-Phuong; van Weij, Marco S.; Reichelt, Michael; Schranz, Michael E.

2017-01-01

The biochemical defense of plants can change during their life-cycle and impact herbivore feeding and plant fitness. The annual species Aethionema arabicum is part of the sister clade to all other Brassicaceae. Hence, it holds a phylogenetically important position for studying crucifer trait evolution. Glucosinolates (GS) are essentially Brassicales-specific metabolites involved in plant defense. Using two Ae. arabicum accessions (TUR and CYP) we identify substantial differences in glucosinolate profiles and quantities between lines, tissues and developmental stages. We find tissue specific side-chain modifications in aliphatic GS: methylthioalkyl in leaves, methylsulfinylalkyl in fruits, and methylsulfonylalkyl in seeds. We also find large differences in absolute glucosinolate content between the two accessions (up to 10-fold in fruits) that suggest a regulatory factor is involved that is not part of the quintessential glucosinolate biosynthetic pathway. Consistent with this hypothesis, we identified a single major multi-trait quantitative trait locus controlling total GS concentration across tissues in a recombinant inbred line population derived from TUR and CYP. With fine-mapping, we narrowed the interval to a 58 kb region containing 15 genes, but lacking any known GS biosynthetic genes. The interval contains homologs of both the sulfate transporter SULTR2;1 and FLOWERING LOCUS C. Both loci have diverse functions controlling plant physiological and developmental processes and thus are potential candidates regulating glucosinolate variation across the life-cycle of Aethionema. Future work will investigate changes in gene expression of the candidates genes, the effects of GS variation on insect herbivores and the trade-offs between defense and reproduction. PMID:28603537

Image quality specification and maintenance for airborne SAR

NASA Astrophysics Data System (ADS)

Clinard, Mark S.

2004-08-01

Specification, verification, and maintenance of image quality over the lifecycle of an operational airborne SAR begin with the specification for the system itself. Verification of image quality-oriented specification compliance can be enhanced by including a specification requirement that a vendor provide appropriate imagery at the various phases of the system life cycle. The nature and content of the imagery appropriate for each stage of the process depends on the nature of the test, the economics of collection, and the availability of techniques to extract the desired information from the data. At the earliest lifecycle stages, Concept and Technology Development (CTD) and System Development and Demonstration (SDD), the test set could include simulated imagery to demonstrate the mathematical and engineering concepts being implemented thus allowing demonstration of compliance, in part, through simulation. For Initial Operational Test and Evaluation (IOT&E), imagery collected from precisely instrumented test ranges and targets of opportunity consisting of a priori or a posteriori ground-truthed cultural and natural features are of value to the analysis of product quality compliance. Regular monitoring of image quality is possible using operational imagery and automated metrics; more precise measurements can be performed with imagery of instrumented scenes, when available. A survey of image quality measurement techniques is presented along with a discussion of the challenges of managing an airborne SAR program with the scarce resources of time, money, and ground-truthed data. Recommendations are provided that should allow an improvement in the product quality specification and maintenance process with a minimal increase in resource demands on the customer, the vendor, the operational personnel, and the asset itself.

Flowering Locus C (FLC) Is a Potential Major Regulator of Glucosinolate Content across Developmental Stages of Aethionema arabicum (Brassicaceae).

PubMed

Mohammadin, Setareh; Nguyen, Thu-Phuong; van Weij, Marco S; Reichelt, Michael; Schranz, Michael E

2017-01-01

The biochemical defense of plants can change during their life-cycle and impact herbivore feeding and plant fitness. The annual species Aethionema arabicum is part of the sister clade to all other Brassicaceae. Hence, it holds a phylogenetically important position for studying crucifer trait evolution. Glucosinolates (GS) are essentially Brassicales-specific metabolites involved in plant defense. Using two Ae. arabicum accessions (TUR and CYP) we identify substantial differences in glucosinolate profiles and quantities between lines, tissues and developmental stages. We find tissue specific side-chain modifications in aliphatic GS: methylthioalkyl in leaves, methylsulfinylalkyl in fruits, and methylsulfonylalkyl in seeds. We also find large differences in absolute glucosinolate content between the two accessions (up to 10-fold in fruits) that suggest a regulatory factor is involved that is not part of the quintessential glucosinolate biosynthetic pathway. Consistent with this hypothesis, we identified a single major multi-trait quantitative trait locus controlling total GS concentration across tissues in a recombinant inbred line population derived from TUR and CYP. With fine-mapping, we narrowed the interval to a 58 kb region containing 15 genes, but lacking any known GS biosynthetic genes. The interval contains homologs of both the sulfate transporter SULTR2;1 and FLOWERING LOCUS C . Both loci have diverse functions controlling plant physiological and developmental processes and thus are potential candidates regulating glucosinolate variation across the life-cycle of Aethionema . Future work will investigate changes in gene expression of the candidates genes, the effects of GS variation on insect herbivores and the trade-offs between defense and reproduction.

Development of chronic tests for endocrine active chemicals. Part 1. An extended fish early-life stage test for oestrogenic active chemicals in the fathead minnow (Pimephales promelas).

PubMed

Panter, G H; Hutchinson, T H; Hurd, K S; Bamforth, J; Stanley, R D; Duffell, S; Hargreaves, A; Gimeno, S; Tyler, C R

2006-05-10

An extended early-life stage test (based on OECD test guideline 210) was developed to allow the evaluation of a weak environmental oestrogen, 4-tert-pentyphenol (4TPP), on sexual differentiation and gonadal development. Fathead minnow (Pimephales promelas) embryos were exposed to three concentrations of 4TPP (56, 180 and 560 microg l(-1)) in a flow-through system, at 25+/-1 degrees C, for <107 days post-hatch (dph). In addition, some embryos were exposed to 180 microg 4TPPl(-1) until 30 or 60 dph, after which they were exposed to dilution water only until 107 dph. At 30, 60 and 107 dph fish were evaluated for growth and gonadal development (via histology), and at 107 dph fish were also evaluated for secondary sexual characteristics (SSC), gonadosomatic index (GSI) and plasma vitellogenin (VTG). There were no effects of 4TPP on hatching success or survival, however, there was a delay in the time taken for embryos to hatch (560 microg 4TPPl(-1)). No treatment-related effects were observed on fish growth, with the exception of at 107 dph when the condition factor in female fish was reduced in all 4TPP continuous exposure treatments. Plasma VTG was only elevated in female fish exposed to 180 microg 4TPPl(-1) and inhibition of gonadal growth (GSI) occurred only in females exposed to 560 microg 4TPPl(-1). Histological examination of the gonads revealed delays and disruption in male sexual differentiation and development (180 microg 4TPPl(-1)) and no testicular tissue was observed in any fish exposed to 560 microg 4TPPl(-1). Mixed gonads (predominately testes with a scattering of primary oocytes) were present in fish exposed to all doses of 180 microg 4TPPl(-1) at 107 dph. Feminisation of the reproductive ducts (formation of an ovarian like cavity) occurred in the testis of all males exposed to 180 microg l(-1), regardless of length of 4TPP exposure. Results indicate that the period of 30-60 dph appears to be the sensitive window for disruption of formation of the reproductive duct and this effect is not reversible when the fish are transferred to dilution water. The data also show that this integrative test is suitable for the detection of a weak environmental oestrogen and comparisons of these results with that of a fish full life-cycle, in medaka, indicate that this test could be a suitable surrogate for a fish full life-cycle.

USER'S GUIDE FOR THE MUNICIPAL SOLID WASTE LIFE-CYCLE DATABASE

EPA Science Inventory

The report describes how to use the municipal solid waste (MSW) life cycle database, a software application with Microsoft Access interfaces, that provides environmental data for energy production, materials production, and MSW management activities and equipment. The basic datab...

Biodiesel Research : Alternative Fuels & Life-Cycle Engineering Program : November 29, 2006 to November 28, 2011

DOT National Transportation Integrated Search

2011-12-20

The primary objective of this project is to develop multiple simulation Testbeds/transportation models to evaluate the impacts of DMA connected vehicle applications and the active and dynamic transportation management (ATDM) strategies. The outputs (...

Analysis of Life-Cycle Costs and Market Applications of Flywheel Energy-Storage Transit Vehicles

DOT National Transportation Integrated Search

1979-07-01

The Urban Mass Transportation Administration (UMTA) has recently completed the Phase I activities of its Flywheel Energy Storage Program involving an analysis of the operational requirements and the conceptual design of flywheel energy storage vehicl...

Complete mitochondrial genomes and nuclear ribosomal RNA operons of two species of Diplostomum (Platyhelminthes: Trematoda): a molecular resource for taxonomy and molecular epidemiology of important fish pathogens.

PubMed

Brabec, Jan; Kostadinova, Aneta; Scholz, Tomáš; Littlewood, D Timothy J

2015-06-19

The genus Diplostomum (Platyhelminthes: Trematoda: Diplostomidae) is a diverse group of freshwater parasites with complex life-cycles and global distribution. The larval stages are important pathogens causing eye fluke disease implicated in substantial impacts on natural fish populations and losses in aquaculture. However, the problematic species delimitation and difficulties in the identification of larval stages hamper the assessment of the distributional and host ranges of Diplostomum spp. and their transmission ecology. Total genomic DNA was isolated from adult worms and shotgun sequenced using Illumina MiSeq technology. Mitochondrial (mt) genomes and nuclear ribosomal RNA (rRNA) operons were assembled using established bioinformatic tools and fully annotated. Mt protein-coding genes and nuclear rRNA genes were subjected to phylogenetic analysis by maximum likelihood and the resulting topologies compared. We characterised novel complete mt genomes and nuclear rRNA operons of two closely related species, Diplostomum spathaceum and D. pseudospathaceum. Comparative mt genome assessment revealed that the cox1 gene and its 'barcode' region used for molecular identification are the most conserved regions; instead, nad4 and nad5 genes were identified as most promising molecular diagnostic markers. Using the novel data, we provide the first genome wide estimation of the phylogenetic relationships of the order Diplostomida, one of the two fundamental lineages of the Digenea. Analyses of the mitogenomic data invariably recovered the Diplostomidae as a sister lineage of the order Plagiorchiida rather than as a basal lineage of the Diplostomida as inferred in rDNA phylogenies; this was concordant with the mt gene order of Diplostomum spp. exhibiting closer match to the conserved gene order of the Plagiorchiida. Complete sequences of the mt genome and rRNA operon of two species of Diplostomum provide a valuable resource for novel genetic markers for species delineation and large-scale molecular epidemiology and disease ecology studies based on the most accessible life-cycle stages of eye flukes.

Identification of in vivo regulators of the Vibrio cholerae xds gene using a high-throughput genetic selection

PubMed Central

McDonough, EmilyKate; Lazinski, David W.; Camilli, Andrew

2014-01-01

Summary Vibrio cholerae, the causative agent of cholera, remains a threat to public health in areas with inadequate sanitation. As a waterborne pathogen, V. cholerae moves between two dissimilar environments, aquatic reservoirs and the intestinal tract of humans. Accordingly, this pathogen undergoes adaptive shifts in gene expression throughout the different stages of its lifecycle. One particular gene, xds, encodes a secreted exonuclease that was previously identified as being induced during infection. Here we sought to identify regulators responsible for the in vivo-specific induction of xds. A transcriptional fusion of xds to two consecutive antibiotic resistance genes was used to select transposon mutants that had inserted within or adjacent to regulatory genes and thereby caused increased expression of the xds fusion under non-inducing conditions. Large pools of selected insertion sites were sequenced in a high throughput manner using Tn-seq to identify potential mechanisms of xds regulation. Our selection identified the two-component system PhoB/R as the dominant activator of xds expression. In vitro validation confirmed that PhoB, a protein which is only active during phosphate limitation, was responsible for xds activation. Using xds expression as a biosensor of the extracellular phosphate level, we observed that the mouse small intestine is a phosphate-limited environment. PMID:24673931

Use of a continuous culture fermentation system to investigate the effect of GanedenBC30 (Bacillus coagulans GBI-30, 6086) supplementation on pathogen survival in the human gut microbiota.

PubMed

Honda, Harue; Gibson, Glenn R; Farmer, Sean; Keller, David; McCartney, Anne L

2011-02-01

Single-stage continuous fermentation systems were employed to examine the effects of GanedenBC(30) supplementation on the human gastrointestinal microbiota in relation to pathogen challenge in vitro. Denaturing gradient gel electrophoresis analysis demonstrated that GanedenBC(30) supplementation modified the microbial profiles in the fermentation systems compared with controls, with profiles clustering according to treatment. Overall, GanedenBC(30) supplementation did not elicit major changes in bacterial population counts in vitro, although notably higher Bcoa191 counts were seen following probiotic supplementation (compared to the controls). Pathogen challenge did not elicit significant modification of the microbial counts in vitro, although notably higher Clit135 counts were seen in the control system post-Clostridium difficile challenge than in the corresponding GanedenBC(30)-supplemented systems. Sporulation appears to be associated with the anti-microbial activity of GanedenBC(30), suggesting that a bi-modal lifecycle of GanedenBC(30)in vivo may lead to anti-microbial activity in distal regions of the gastrointestinal tract. Copyright © 2011 Elsevier Ltd. All rights reserved.

Managing Errors to Reduce Accidents in High Consequence Networked Information Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ganter, J.H.

1999-02-01

Computers have always helped to amplify and propagate errors made by people. The emergence of Networked Information Systems (NISs), which allow people and systems to quickly interact worldwide, has made understanding and minimizing human error more critical. This paper applies concepts from system safety to analyze how hazards (from hackers to power disruptions) penetrate NIS defenses (e.g., firewalls and operating systems) to cause accidents. Such events usually result from both active, easily identified failures and more subtle latent conditions that have resided in the system for long periods. Both active failures and latent conditions result from human errors. We classifymore » these into several types (slips, lapses, mistakes, etc.) and provide NIS examples of how they occur. Next we examine error minimization throughout the NIS lifecycle, from design through operation to reengineering. At each stage, steps can be taken to minimize the occurrence and effects of human errors. These include defensive design philosophies, architectural patterns to guide developers, and collaborative design that incorporates operational experiences and surprises into design efforts. We conclude by looking at three aspects of NISs that will cause continuing challenges in error and accident management: immaturity of the industry, limited risk perception, and resource tradeoffs.« less

Life-cycle analysis of bio-based aviation fuels.

PubMed

Han, Jeongwoo; Elgowainy, Amgad; Cai, Hao; Wang, Michael Q

2013-12-01

Well-to-wake (WTWa) analysis of bio-based aviation fuels, including hydroprocessed renewable jet (HRJ) from various oil seeds, Fischer-Tropsch jet (FTJ) from corn-stover and co-feeding of coal and corn-stover, and pyrolysis jet from corn stover, is conducted and compared with petroleum jet. WTWa GHG emission reductions relative to petroleum jet can be 41-63% for HRJ, 68-76% for pyrolysis jet and 89% for FTJ from corn stover. The HRJ production stage dominates WTWa GHG emissions from HRJ pathways. The differences in GHG emissions from HRJ production stage among considered feedstocks are much smaller than those from fertilizer use and N2O emissions related to feedstock collection stage. Sensitivity analyses on FTJ production from coal and corn-stover are also conducted, showing the importance of biomass share in the feedstock, carbon capture and sequestration options, and overall efficiency. For both HRJ and FTJ, co-product handling methods have significant impacts on WTWa results. Copyright © 2013 Elsevier Ltd. All rights reserved.

Competitive Strategies of States: A Life-Cycle Perspective. EQW Working Papers.

ERIC Educational Resources Information Center

Flynn, Patricia M.

This paper demonstrates that production life-cycle models provide a conceptual framework to analyze systematically the interrelationships between industrial and technological change and human resources. Section II presents the life-cycle model, focusing on its implications for the types and level of employment and skill requirements in an area.…

Life Cycle of Tropical Convection and Anvil in Observations and Models

NASA Astrophysics Data System (ADS)

McFarlane, S. A.; Hagos, S. M.; Comstock, J. M.

2011-12-01

Tropical convective clouds are important elements of the hydrological cycle and produce extensive cirrus anvils that strongly affect the tropical radiative energy balance. To improve simulations of the global water and energy cycles and accurately predict both precipitation and cloud radiative feedbacks, models need to realistically simulate the lifecycle of tropical convection, including the formation and radiative properties of ice anvil clouds. By combining remote sensing datasets from precipitation and cloud radars at the Atmospheric Radiation Measurement (ARM) Darwin site with geostationary satellite data, we can develop observational understanding of the lifetime of convective systems and the links between the properties of convective systems and their associated anvil clouds. The relationships between convection and anvil in model simulations can then be compared to those seen in the observations to identify areas for improvement in the model simulations. We identify and track tropical convective systems in the Tropical Western Pacific using geostationary satellite observations. We present statistics of the tropical convective systems including size, age, and intensity and classify the lifecycle stage of each system as developing, mature, or dissipating. For systems that cross over the ARM Darwin site, information on convective intensity and anvil properties are obtained from the C-Pol precipitation radar and MMCR cloud radar, respectively, and are examined as a function of the system lifecycle. Initial results from applying the convective identification and tracking algorithm to a tropical simulation from the Weather Research and Forecasting (WRF) model run show that the model produces reasonable overall statistics of convective systems, but details of the life cycle (such as diurnal cycle, system tracks) differ from the observations. Further work will focus on the role of atmospheric temperature and moisture profiles in the model's convective life cycle.

Impact of tool wear on cross wedge rolling process stability and on product quality

NASA Astrophysics Data System (ADS)

Gutierrez, Catalina; Langlois, Laurent; Baudouin, Cyrille; Bigot, Régis; Fremeaux, Eric

2017-10-01

Cross wedge rolling (CWR) is a metal forming process used in the automotive industry. One of its applications is in the manufacturing process of connecting rods. CWR transforms a cylindrical billet into a complex axisymmetrical shape with an accurate distribution of material. This preform is forged into shape in a forging die. In order to improve CWR tool lifecycle and product quality it is essential to understand tool wear evolution and the physical phenomena that change on the CWR process due to the resulting geometry of the tool when undergoing tool wear. In order to understand CWR tool wear behavior, numerical simulations are necessary. Nevertheless, if the simulations are performed with the CAD geometry of the tool, results are limited. To solve this difficulty, two numerical simulations with FORGE® were performed using the real geometry of the tools (both up and lower roll) at two different states: (1) before starting lifecycle and (2) end of lifecycle. The tools were 3D measured with ATOS triple scan by GOM® using optical 3D measuring techniques. The result was a high-resolution point cloud of the entire geometry of the tool. Each 3D point cloud was digitalized and converted into a STL format. The geometry of the tools in a STL format was input for the 3D simulations. Both simulations were compared. Defects of products obtained in simulation were compared to main defects of products found industrially. Two main defects are: (a) surface defects on the preform that are not fixed in the die forging operation; and (b) Preform bent (no longer straight), with two possible impacts: on the one hand that the robot cannot grab it to take it to the forging stage; on the other hand, an unfilled section in the forging operation.

An XML-Based Manipulation and Query Language for Rule-Based Information

NASA Astrophysics Data System (ADS)

Mansour, Essam; Höpfner, Hagen

Rules are utilized to assist in the monitoring process that is required in activities, such as disease management and customer relationship management. These rules are specified according to the application best practices. Most of research efforts emphasize on the specification and execution of these rules. Few research efforts focus on managing these rules as one object that has a management life-cycle. This paper presents our manipulation and query language that is developed to facilitate the maintenance of this object during its life-cycle and to query the information contained in this object. This language is based on an XML-based model. Furthermore, we evaluate the model and language using a prototype system applied to a clinical case study.

Cost Model Comparison: A Study of Internally and Commercially Developed Cost Models in Use by NASA

NASA Technical Reports Server (NTRS)

Gupta, Garima

2011-01-01

NASA makes use of numerous cost models to accurately estimate the cost of various components of a mission - hardware, software, mission/ground operations - during the different stages of a mission's lifecycle. The purpose of this project was to survey these models and determine in which respects they are similar and in which they are different. The initial survey included a study of the cost drivers for each model, the form of each model (linear/exponential/other CER, range/point output, capable of risk/sensitivity analysis), and for what types of missions and for what phases of a mission lifecycle each model is capable of estimating cost. The models taken into consideration consisted of both those that were developed by NASA and those that were commercially developed: GSECT, NAFCOM, SCAT, QuickCost, PRICE, and SEER. Once the initial survey was completed, the next step in the project was to compare the cost models' capabilities in terms of Work Breakdown Structure (WBS) elements. This final comparison was then portrayed in a visual manner with Venn diagrams. All of the materials produced in the process of this study were then posted on the Ground Segment Team (GST) Wiki.

Integrating legal liabilities in nanomanufacturing risk management.

PubMed

Mohan, Mayank; Trump, Benjamin D; Bates, Matthew E; Monica, John C; Linkov, Igor

2012-08-07

Among other things, the wide-scale development and use of nanomaterials is expected to produce costly regulatory and civil liabilities for nanomanufacturers due to lingering uncertainties, unanticipated effects, and potential toxicity. The life-cycle environmental, health, and safety (EHS) risks of nanomaterials are currently being studied, but the corresponding legal risks have not been systematically addressed. With the aid of a systematic approach that holistically evaluates and accounts for uncertainties about the inherent properties of nanomaterials, it is possible to provide an order of magnitude estimate of liability risks from regulatory and litigious sources based on current knowledge. In this work, we present a conceptual framework for integrating estimated legal liabilities with EHS risks across nanomaterial life-cycle stages using empirical knowledge in the field, scientific and legal judgment, probabilistic risk assessment, and multicriteria decision analysis. Such estimates will provide investors and operators with a basis to compare different technologies and practices and will also inform regulatory and legislative bodies in determining standards that balance risks with technical advancement. We illustrate the framework through the hypothetical case of a manufacturer of nanoscale titanium dioxide and use the resulting expected legal costs to evaluate alternative risk-management actions.

Chronic effects of low-level mercury and cadmium to goldfish (Carassius Auratus)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westerman, A.G.

1984-01-01

During this five and one half year investigation, experiments were performed to determine the effects of nanogram levels of cadmium and mercury on reproductive performance, growth, and tissue residues of goldfish. In addition, embryo-larval bioassays were conducted on these metals to compare the effects of a short-term exposure to a sensitive life-cycle stage (i.e., eggs and larvae) with a sustained exposure to a relatively insensitive life-cycle period (i.e., adult). Reproduction was blocked by the long-term exposure to 0.25 ..mu..g/l mercury and 0.27 ..mu..g/l cadmium. Over the 1972 days, the control fish spawned on eleven occasions, but the experimentals failed tomore » spawn. The metal-induced reproductive impairment continued in the experimentals even after six months in clean water. Growth of the populations exposed to mercury and cadmium was significantly less than that of the control population (P < 0.001). The mercury, cadmium and control populations grew by 229%, 232% and 353%, respectively. Mercury and cadmium continuously accumulated in fish tissues over the entire 1789 days of whole body exposure. Despite exposure to mercury as inorganic metal, organomercury also accumula« less

Gate-to-gate Life-Cycle Inventory of Hardboard Production in North America

Treesearch

Richard Bergman

2014-01-01

Whole-building life-cycle assessments (LCAs) populated by life-cycle inventory (LCI) data are incorporated into environmental footprint software tools for establishing green building certification by building professionals and code. However, LCI data on some wood building products are still needed to help fill gaps in the data and thus provide a more complete picture...

Reusability Studies for Ares I and Ares V Propulsion

NASA Technical Reports Server (NTRS)

Williams, Thomas J.; Priskos, Alex S.; Schorr, Andrew A.; Barrett, Gregory

2008-01-01

With a mission to continue to support the goals of the International Space Station (ISS) and explore beyond Earth orbit, the United States National Aeronautics and Space Administration (NASA) is in the process of launching an entirely new space exploration initiative, the Constellation Program. Even as the Space Shuttle moves toward its final voyage, Constellation is building from nearly half a century of NASA spaceflight experience, and technological advances, including the legacy of Shuttle and earlier programs such as Apollo and the Saturn V rocket. Out of Constellation will come two new launch vehicles: the Ares I crew launch vehicle and the Ares V cargo launch vehicle. With the initial goal to seamlessly continue where the Space Shuttle leaves off, Ares will firstly service the Space Station. Ultimately, however, the intent is to push further: to establish an outpost on the Moon, and then to explore other destinations. With significant experience and a strong foundation in aerospace, NASA is now progressing toward the final design of the First Stage propulsion system for the Ares I. The new launch vehicle design will considerably increase safety and reliability, reduce the cost of accessing space, and provide a viable growth path for human space exploration. To achieve these goals, NASA is taking advantage of Space Shuttle hardware, safety, reliability, and experience. With efforts to minimize technical risk and life-cycle costs, the First Stage office is again pulling from NASA's strong legacy in aerospace exploration and development, most specifically the Space Shuttle Program. Trade studies have been conducted to evaluate lifecycle costs, expendability, and risk reduction. While many first stage features have already been determined, these trade studies are helping to resolve the operational requisites and configuration of the first stage element. This paper first presents an overview of the Ares missions and the genesis of the Ares vehicle design. It then looks at one of the most important trade studies to date, the "Ares I First Stage Expendability Trade Study." The purpose of this study was to determine the utility of flying the first stage as an expendable booster rather than making it reusable. To lower the study complexity, four operational scenarios (or cases) were defined. This assessment then included an evaluation of the development, reliability, performance, and transition impacts associated with an expendable solution. The paper looks at these scenarios from the perspectives of cost, reliability, and performance. The presentation provides an overview of the paper.

Reusability Studies for Ares I and Ares V Propulsion

NASA Technical Reports Server (NTRS)

Williams, Thomas J.; Priskos, Alex S.; Schorr, Andrew A.; Barrett, Greg

2008-01-01

With a mission to continue to support the goals of the International Space Station (ISS) and explore beyond Earth orbit, the United States National Aeronautics and Space Administration (NASA) is in the process of launching an entirely new space exploration initiative, the Constellation Program. Even as the Space Shuttle moves toward its final voyage, Constellation is building from nearly half a century of NASA spaceflight experience, and technological advances, including the legacy of Shuttle and earlier programs such as Apollo and the Saturn V rocket. Out of Constellation will come two new launch vehicles: the Ares I crew launch vehicle and the Ares V cargo launch vehicle. With the initial goal to seamlessly continue where the Space Shuttle leaves off, Ares will firstly service the Space Station. Ultimately, however, the intent is to push further: to establish an outpost on the Moon, and then to explore other destinations. With significant experience and a strong foundation in aerospace, NASA is now progressing toward the final design of the First Stage propulsion system for the Ares I. The new launch vehicle design will considerably increase safety and reliability, reduce the cost of accessing space, and provide a viable growth path for human space exploration. To achieve these goals, NASA is taking advantage of Space Shuttle hardware, safety, reliability, and experience. With efforts to minimize technical risk and life-cycle costs, the First Stage office is again pulling from NASA s strong legacy in aerospace exploration and development, most specifically the Space Shuttle Program. Trade studies have been conducted to evaluate life-cycle costs, expendability, and risk reduction. While many first stage features have already been determined, these trade studies are helping to resolve the operational requisites and configuration of the first stage element. This paper first presents an overview of the Ares missions and the genesis of the Ares vehicle design. It then looks at one of the most important trade studies to date, the "Ares I First Stage Expendability Trade Study." The purpose of this study was to determine the utility of flying the first stage as an expendable booster rather than making it reusable. To lower the study complexity, four operational scenarios (or cases) were defined. This assessment then included an evaluation of the development, reliability, performance, and transition impacts associated with an expendable solution. This paper looks at these scenarios from the perspectives of cost, reliability, and performance.

PRODUCT LIFE-CYCLE ASSESSMENT: INVENTORY GUIDELINES AND PRINCIPLES

EPA Science Inventory

The Life Cycle Assessment (LCA) can be used as an objective technical tool to evaluate the environmental consequences of a product, process, or activity holistically, across its entire life cycle. omplete LCA can be viewed as consisting of three complementary components (1) the i...

The Lifecycle of Bayesian Network Models Developed for Multi-Source Signature Assessment of Nuclear Programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gastelum, Zoe N.; White, Amanda M.; Whitney, Paul D.

2013-06-04

The Multi-Source Signatures for Nuclear Programs project, part of Pacific Northwest National Laboratory’s (PNNL) Signature Discovery Initiative, seeks to computationally capture expert assessment of multi-type information such as text, sensor output, imagery, or audio/video files, to assess nuclear activities through a series of Bayesian network (BN) models. These models incorporate knowledge from a diverse range of information sources in order to help assess a country’s nuclear activities. The models span engineering topic areas, state-level indicators, and facility-specific characteristics. To illustrate the development, calibration, and use of BN models for multi-source assessment, we present a model that predicts a country’s likelihoodmore » to participate in the international nuclear nonproliferation regime. We validate this model by examining the extent to which the model assists non-experts arrive at conclusions similar to those provided by nuclear proliferation experts. We also describe the PNNL-developed software used throughout the lifecycle of the Bayesian network model development.« less

Life-cycle inventory of hardwood lumber manufacturing in the Northeastern and North Central United States.

Treesearch

Richard Bergman; Scott A. Bowe

2007-01-01

The goal of this study was to find the environmental impact of hardwood lumber production through a gate-to-gate Life-Cycle Inventory (LCI) on hardwood sawmills in the northeast and northcentral (NE/NC) United States. Primary mill data was collected per CORRIM Research Guidelines (CORRIM 2001). Lifecycle analysis is beyond the scope of the study.

Life-Cycle Thinking in Inquiry-Based Sustainability Education--Effects on Students' Attitudes towards Chemistry and Environmental Literacy

ERIC Educational Resources Information Center

Juntunen, Marianne; Aksela, Maija

2013-01-01

The aim of the present study is to improve the quality of students' environmental literacy and sustainability education in chemistry teaching by combining the socio-scientific issue of life-cycle thinking with inquiry-based learning approaches. This case study presents results from an inquiry-based life-cycle thinking project: an interdisciplinary…

Life-cycle assessment of redwood decking in the United States with a comparison to three other decking materials

Treesearch

R. Bergman; H. Sup-Han; E. Oneil; I. Eastin

2013-01-01

The goal of the study was to conduct a life-cycle inventory (LCI) of California redwood (Sequoia sempervirens) decking that would quantify the critical environmental impacts of decking from cradle to grave. Using that LCI data, a life-cycle assessment (LCA) was produced for redwood decking. The results were used to compare the environmental footprint...

Product Lifecycle Management Architecture: A Model Based Systems Engineering Analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noonan, Nicholas James

2015-07-01

This report is an analysis of the Product Lifecycle Management (PLM) program. The analysis is centered on a need statement generated by a Nuclear Weapons (NW) customer. The need statement captured in this report creates an opportunity for the PLM to provide a robust service as a solution. Lifecycles for both the NW and PLM are analyzed using Model Based System Engineering (MBSE).

Building Information Modeling (BIM) Primer. Report 1: Facility Life-Cycle Process and Technology Innovation

DTIC Science & Technology

2012-08-01

Building Information Modeling ( BIM ) Primer Report 1: Facility Life-cycle Process and Technology Innovation In fo...is unlimited. ERDC/ITL TR-12-2 August 2012 Building Information Modeling ( BIM ) Primer Report 1: Facility Life-cycle Process and Technology...and to enhance the quality of projects through the design, construction, and handover phases. Building Information Modeling ( BIM ) is a

The lifespan and life-cycle of self-help groups: a retrospective study of groups in Nottingham, UK.

PubMed

Chaudhary, Sarah; Avis, Mark; Munn-Giddings, Carol

2010-07-01

This article is based on an analysis of a practice database held by Self Help Nottingham, an organisation that supports local self-help groups. The database contains details of 936 groups that closed between 1982 and 2007. The aim of the study is to provide qualitative and descriptive quantitative information about the life-cycles of self-help groups, the problems that they face throughout their existence and the likelihood of different problems leading to their closure. The database was not collated for research purposes and so we restrict our discussion of the findings to identification of broad patterns regarding the birth and closure rates of different types of group and questions for future research. Comparisons were made between groups that addressed different types of problem, groups with different memberships and groups that had reached different stages in their existence. There was reasonable consistency in the survival rates of different types of group with physical health groups being the most likely to reach maturity followed by mental health and lastly social issue groups. Survival rates for groups that serve different membership populations were reasonably constant although there were some anomalies. There were high levels of consistency regarding the reasons for closure for groups closing at different stages of maturity. The most commonly cited reasons among all groups were the withdrawal of a 'key' member and a decline in membership. The article suggests that some of the assumptions and prescriptions within the existing literature need to be considered in light of more detailed empirical evidence, and it raises questions about the theoretical understanding of self-help groups.

Cooperative vaccinia infection demonstrated at the single-cell level using FluidFM.

PubMed

Stiefel, Philipp; Schmidt, Florian I; Dörig, Pablo; Behr, Pascal; Zambelli, Tomaso; Vorholt, Julia A; Mercer, Jason

2012-08-08

The mechanisms used by viruses to enter and replicate within host cells are subjects of intense investigation. These studies are ultimately aimed at development of new drugs that interfere with these processes. Virus entry and infection are generally monitored by dispensing bulk virus suspensions on layers of cells without accounting for the fate of each virion. Here, we take advantage of the recently developed FluidFM to deposit single vaccinia virions onto individual cells in a controlled manner. While the majority of virions were blocked prior to early gene expression, infection of individual cells increased in a nondeterministic fashion with respect to the number of viruses placed. Microscopic analyses of several stages of the virus lifecycle indicated that this was the result of cooperativity between virions during early stages of infection. These findings highlight the importance of performing controlled virus infection experiments at the single cell level.

Ontology for Life-Cycle Modeling of Water Distribution Systems: Model View Definition

DTIC Science & Technology

2013-06-01

Research and Development Center, Construction Engineering Research Laboratory (ERDC-CERL) to develop a life-cycle building model have resulted in the...Laboratory (ERDC-CERL) to develop a life-cycle building model have resulted in the definition of a “core” building information model that contains...developed experimental BIM models us- ing commercial off-the-shelf (COTS) software. Those models represent three types of typical low-rise Army

Policy implications of uncertainty in modeled life-cycle greenhouse gas emissions of biofuels.

PubMed

Mullins, Kimberley A; Griffin, W Michael; Matthews, H Scott

2011-01-01

Biofuels have received legislative support recently in California's Low-Carbon Fuel Standard and the Federal Energy Independence and Security Act. Both present new fuel types, but neither provides methodological guidelines for dealing with the inherent uncertainty in evaluating their potential life-cycle greenhouse gas emissions. Emissions reductions are based on point estimates only. This work demonstrates the use of Monte Carlo simulation to estimate life-cycle emissions distributions from ethanol and butanol from corn or switchgrass. Life-cycle emissions distributions for each feedstock and fuel pairing modeled span an order of magnitude or more. Using a streamlined life-cycle assessment, corn ethanol emissions range from 50 to 250 g CO(2)e/MJ, for example, and each feedstock-fuel pathway studied shows some probability of greater emissions than a distribution for gasoline. Potential GHG emissions reductions from displacing fossil fuels with biofuels are difficult to forecast given this high degree of uncertainty in life-cycle emissions. This uncertainty is driven by the importance and uncertainty of indirect land use change emissions. Incorporating uncertainty in the decision making process can illuminate the risks of policy failure (e.g., increased emissions), and a calculated risk of failure due to uncertainty can be used to inform more appropriate reduction targets in future biofuel policies.

Enzymes involved in plastid-targeted phosphatidic acid synthesis are essential for Plasmodium yoelii liver stage development

PubMed Central

Lindner, Scott E.; Sartain, Mark J.; Hayes, Kiera; Harupa, Anke; Moritz, Robert L.; Kappe, Stefan H. I.; Vaughan, Ashley M.

2014-01-01

SUMMARY Malaria parasites scavenge nutrients from their host but also harbor enzymatic pathways for de novo macromolecule synthesis. One such pathway is apicoplast-targeted type II fatty acid synthesis, which is essential for late liver stage development in rodent malaria. It is likely that fatty acids synthesized in the apicoplast are ultimately incorporated into membrane phospholipids necessary for exoerythrocytic merozoite formation. We hypothesized that these synthesized fatty acids are being utilized for apicoplast-targeted phosphatidic acid synthesis, the phospholipid precursor. Phosphatidic acid is typically synthesized in a three-step reaction utilizing three enzymes: glycerol 3-phosphate dehydrogenase, glycerol 3-phosphate acyltransferase and lysophosphatidic acid acyltransferase. The Plasmodium genome is predicted to harbor genes for both apicoplast- and cytosol/endoplasmic reticulum-targeted phosphatidic synthesis. Our research shows that apicoplast-targeted P. yoelii glycerol 3-phosphate dehydrogenase and glycerol 3-phosphate acyltransferase are expressed only during liver stage development and deletion of the encoding genes resulted in late liver stage growth arrest and lack of merozoite differentiation. However, the predicted apicoplast-targeted lysophosphatidic acid acyltransferase gene was refractory to deletion and was expressed solely in the endoplasmic reticulum throughout the parasite lifecycle. Our results suggest that P. yoelii has an incomplete apicoplast-targeted phosphatidic acid synthesis pathway that is essential for liver stage maturation. PMID:24330260

A RabGAP Regulates Life-Cycle Duration via Trimeric G-protein Cascades in Dictyostelium discoideum

PubMed Central

Kuwayama, Hidekazu; Miyanaga, Yukihiro; Urushihara, Hideko; Ueda, Masahiro

2013-01-01

Background The life-cycle of cellular slime molds comprises chronobiologically regulated processes. During the growth phase, the amoeboid cells proliferate at a definite rate. Upon starvation, they synthesize cAMP as both first and second messengers in signalling pathways and form aggregates, migrating slugs, and fruiting bodies, consisting of spores and stalk cells, within 24 h. In Dictyostelium discoideum, because most growth-specific events cease during development, proliferative and heterochronic mutations are not considered to be interrelated and no genetic factor governing the entire life-cycle duration has ever been identified. Methodology/Principal Findings Using yeast 2-hybrid library screening, we isolated a Dictyostelium discoideum RabGAP, Dd Rbg-3, as a candidate molecule by which the Dictyostelium Gα2 subunit directs its effects. Rab GTPase-activating protein, RabGAP, acts as a negative regulator of Rab small GTPases, which orchestrate the intracellular membrane trafficking involved in cell proliferation. Deletion mutants of Dd rbg-3 exhibited an increased growth rate and a shortened developmental period, while an overexpression mutant demonstrated the opposite effects. We also show that Dd Rbg-3 interacts with 2 Gα subunits in an activity-dependent manner in vitro. Furthermore, both human and Caenorhabditis elegans rbg-3 homologs complemented the Dd rbg-3–deletion phenotype in D. discoideum, indicating that similar pathways may be generally conserved in multicellular organisms. Conclusions/Significance Our findings suggest that Dd Rbg-3 acts as a key element regulating the duration of D. discoideum life-span potentially via trimeric G-protein cascades. PMID:24349132

Oh, Miss Jones! Where Did You Get That Beautiful Butterfly?

ERIC Educational Resources Information Center

Goldhaber, Jeanne

1998-01-01

Uses four children's explanations to illustrate their use of assimilation and inference in a butterfly life-cycle activity. Describes how interviewing young children about their understanding, and recording and reflecting upon their answers, can allow teachers to better understand how students process information and construct knowledge, and…

Articulating the Resources for Business Process Analysis and Design

ERIC Educational Resources Information Center

Jin, Yulong

2012-01-01

Effective process analysis and modeling are important phases of the business process management lifecycle. When many activities and multiple resources are involved, it is very difficult to build a correct business process specification. This dissertation provides a resource perspective of business processes. It aims at a better process analysis…

77 FR 50719 - Agency Information Collection Activities: Proposed Collection; Comments Requested: Community...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-22

... System (GMS) ACTION: 30-Day Notice of Information Collection Under Review. The Department of Justice (DOJ... (1121-0243). (2) The Title of the Form/Collection: Community Partnership Grants Management System (GMS... system and award management system. GMS provides automated support throughout the award lifecycle. GMS...

Determination of metabolic resistance mechanisms in pyrethroid-resistant and fipronil-tolerant brown dog ticks

USDA-ARS?s Scientific Manuscript database

Rhipicephalus sanguineus (Latreille) (Ixodida: Ixodidae) is a three-host dog tick found worldwide that is able to complete its’ entire lifecycle indoors. Options for the management of R. sanguineus are limited and its’ control relies largely on only a few acaricidal active ingredients. Previous stud...

Environmental aging alters AI(OH)3 coating of TiO2 nanoparticles enhancing their photocatalytic and phototoxicity activities

EPA Science Inventory

It is important to evaluate the potential effects of engineered nanomaterials (ENM) across the lifecycle of nanomaterial-enabled products including transformations in the environment that mayeither gain or lose functional properties. For example, uncoated titanium dioxide (Ti02)...

Data Preservation, Information Preservation, and Lifecyle of Information Management at NASA GES DISC

NASA Technical Reports Server (NTRS)

Khayat, Mo; Kempler, Steve; Deshong, Barbara; Johnson, James; Gerasimov, Irina; Esfandiari, Ed; Berganski, Michael; Wei, Jennifer

2014-01-01

Data lifecycle management awareness is common today; planners are more likely to consider lifecycle issues at mission start. NASA remote sensing missions are typically subject to life cycle management plans of the Distributed Active Archive Center (DAAC), and NASA invests in these national centers for the long-term safeguarding and benefit of future generations. As stewards of older missions, it is incumbent upon us to ensure that a comprehensive enough set of information is being preserved to prevent the risk for information loss. This risk is greater when the original data experts have moved on or are no longer available. Preservation of items like documentation related to processing algorithms, pre-flight calibration data, or input-output configuration parameters used in product generation, are examples of digital artifacts that are sometimes not fully preserved. This is the grey area of information preservation; the importance of these items is not always clear and requires careful consideration. Missing important metadata about intermediate steps used to derive a product could lead to serious challenges in the reproducibility of results or conclusions. Organizations are rapidly recognizing that the focus of life-cycle preservation needs to be enlarged from the strict raw data to the more encompassing arena of information lifecycle management. By understanding what constitutes information, and the complexities involved, we are better equipped to deliver longer lasting value about the original data and derived knowledge (information) from them. The NASA Earth Science Data Preservation Content Specification is an attempt to define the content necessary for long-term preservation. It requires new lifecycle infrastructure approach along with content repositories to accommodate artifacts other than just raw data. The NASA Goddard Earth Sciences Data and Information Services Center (GES DISC) setup an open-source Preservation System capable of long-term archive of digital content to augment its raw data holding. This repository is being used for such missions as HIRDLS, UARS, TOMS, OMI, among others. We will provide a status of this implementation; report on challenges, lessons learned, and detail our plans for future evolution to include other missions and services.

Data Preservation, Information Preservation, and life-cyle of information management at NASA GES DISC

NASA Astrophysics Data System (ADS)

Khayat, M. G.; Deshong, B.; Esfandiari, A. E.; Gerasimov, I. V.; Johnson, J. E.; Kempler, S. J.; Wei, J. C.

2014-12-01

Data lifecycle management awareness is common today; planners are more likely to consider lifecycle issues at mission start. NASA remote sensing missions are typically subject to life cycle management plans of the Distributed Active Archive Center (DAAC), and NASA invests in these national centers for the long-term safeguarding and benefit of future generations. As stewards of older missions, it is incumbent upon us to ensure that a comprehensive enough set of information is being preserved to prevent the risk for "information loss". This risk is greater when the original data experts have moved on or are no longer available. Preservation of items like documentation related to processing algorithms, pre-flight calibration data, or input/output configuration parameters used in product generation, are examples of digital artifacts that are sometimes not fully preserved. This is the grey area of "information preservation"; the importance of these items is not always clear and requires careful consideration. Missing important "metadata" about intermediate steps used to derive a product could lead to serious challenges in the reproducibility of results or conclusions.Organizations are rapidly recognizing that the focus of life-cycle preservation needs to be enlarged from the strict raw data to the more encompassing arena of "information lifecycle management". By understanding what constitutes information, and the complexities involved, we are better equipped to deliver longer lasting value about the original data and derived knowledge (information) from them. The "NASA Earth Science Data Preservation Content Specification" is an attempt to define the content necessary for long-term preservation. It requires new lifecycle infrastructure approach along with content repositories to accommodate artifacts other than just raw data. The NASA Goddard Earth Sciences Data and Information Services Center (GES DISC) setup an open-source Preservation System capable of long-term archive of digital content to augment its raw data holding. This repository is being used for such missions as HIRDLS, UARS, TOMS, OMI, among others. We will provide a status of this implementation; report on challenges, lessons learned, and detail our plans for future evolution to include other missions and services.

Ligand binding assays in the 21st century laboratory: recommendations for characterization and supply of critical reagents.

PubMed

O'Hara, Denise M; Theobald, Valerie; Egan, Adrienne Clements; Usansky, Joel; Krishna, Murli; TerWee, Julie; Maia, Mauricio; Spriggs, Frank P; Kenney, John; Safavi, Afshin; Keefe, Jeannine

2012-06-01

Critical reagents are essential components of ligand binding assays (LBAs) and are utilized throughout the process of drug discovery, development, and post-marketing monitoring. Successful lifecycle management of LBA critical reagents minimizes assay performance problems caused by declining reagent activity and can mitigate the risk of delays during preclinical and clinical studies. Proactive reagent management assures adequate supply. It also assures that the quality of critical reagents is appropriate and consistent for the intended LBA use throughout all stages of the drug development process. This manuscript summarizes the key considerations for the generation, production, characterization, qualification, documentation, and management of critical reagents in LBAs, with recommendations for antibodies (monoclonal and polyclonal), engineered proteins, peptides, and their conjugates. Recommendations are given for each reagent type on basic and optional characterization profiles, expiration dates and storage temperatures, and investment in a knowledge database system. These recommendations represent a consensus among the authors and should be used to assist bioanalytical laboratories in the implementation of a best practices program for critical reagent life cycle management.

Planning factors for developing an enterprise-wide picture archiving and communication system maintenance program.

PubMed

Staley, S; Romlein, J; Chacko, A K; Wider, R

2000-05-01

Picture archiving and communication system (PACS) maintenance on an individual site basis has historically been a complex and costly challenge. With the advent of enterprise-wide PACS projects such as the Virtual Radiology Environment (VRE) project, the challenge of a maintenance program with even more complexities has presented itself. The approach of the project management team for the VRE project is not one of reactive maintenance, but one of highly proactive planning and negotiations, in hopes of capitalizing on the economies of scale of an enterprise-wide PACS maintenance program. A proactive maintenance program is one aspect of life-cycle management. As with any capital acquisition, life-cycle management may be used to manage the specific project aspects related to PACS. The purpose of an enterprise-wide warranty and maintenance life-cycle management approach is to maintain PACS at its maximum operational efficiency and utilization levels through a flexible, shared, yet symbiotic relationship between local, regional, and vendor resources. These goals include providing maximum operational performance levels on a local, regional, and enterprise basis, while maintaining acceptable costs and resource utilization levels. This goal must be achieved without negatively impacting point of care activities, regardless of changes to the clinical business environment.

Updated estimation of energy efficiencies of U.S. petroleum refineries.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palou-Rivera, I.; Wang, M. Q.

2010-12-08

Evaluation of life-cycle (or well-to-wheels, WTW) energy and emission impacts of vehicle/fuel systems requires energy use (or energy efficiencies) of energy processing or conversion activities. In most such studies, petroleum fuels are included. Thus, determination of energy efficiencies of petroleum refineries becomes a necessary step for life-cycle analyses of vehicle/fuel systems. Petroleum refinery energy efficiencies can then be used to determine the total amount of process energy use for refinery operation. Furthermore, since refineries produce multiple products, allocation of energy use and emissions associated with petroleum refineries to various petroleum products is needed for WTW analysis of individual fuels suchmore » as gasoline and diesel. In particular, GREET, the life-cycle model developed at Argonne National Laboratory with DOE sponsorship, compares energy use and emissions of various transportation fuels including gasoline and diesel. Energy use in petroleum refineries is key components of well-to-pump (WTP) energy use and emissions of gasoline and diesel. In GREET, petroleum refinery overall energy efficiencies are used to determine petroleum product specific energy efficiencies. Argonne has developed petroleum refining efficiencies from LP simulations of petroleum refineries and EIA survey data of petroleum refineries up to 2006 (see Wang, 2008). This memo documents Argonne's most recent update of petroleum refining efficiencies.« less

Prophage-Encoded Staphylococcal Enterotoxin A: Regulation of Production in Staphylococcus aureus Strains Representing Different Sea Regions

PubMed Central

Zeaki, Nikoleta; Budi Susilo, Yusak; Pregiel, Anna; Rådström, Peter; Schelin, Jenny

2015-01-01

The present study investigates the nature of the link between the staphylococcal enterotoxin A (SEA) gene and the lifecycle of Siphoviridae bacteriophages, including the origin of strain variation regarding SEA production after prophage induction. Five strains representing three different genetic lines of the sea region were studied under optimal and prophage-induced growth conditions and the Siphoviridae lifecycle was followed through the phage replicative form copies and transcripts of the lysogenic repressor, cro. The role of SOS response on prophage induction was addressed through recA transcription in a recA-disruption mutant. Prophage induction was found to increase the abundance of the phage replicative form, the sea gene copies and transcripts and enhance SEA production. Sequence analysis of the sea regions revealed that observed strain variances were related to strain capacity for prophage induction, rather than sequence differences in the sea region. The impact of SOS response activation on the phage lifecycle was demonstrated by the absence of phage replicative form copies in the recA-disruption mutant after prophage induction. From this study it emerges that all aspects of SEA-producing strain, the Siphoviridae phage and the food environment must be considered when evaluating SEA-related hazards. PMID:26690218

Cradle-to-gate life-cycle assessment of laminated veneer lumber produced in the southeast region of the United States

Treesearch

Richard D. Bergman; Sevda Alanya-Rosenbaum

2017-01-01

The goal of the present study was to develop life-cycle impact assessment (LCIA) data associated with gate-to-gate laminated veneer lumber (LVL) production in the southeast (SE) region of the U.S. with the ultimate aim of constructing an updated cradle-to-gate mill output life-cycle assessment (LCA). The authors collected primary (survey) mill data from LVL production...

Ontology for Life-Cycle Modeling of Water Distribution Systems: Application of Model View Definition Attributes

DTIC Science & Technology

2013-06-01

ER D C/ CE RL C R- 13 -5 Ontology for Life-Cycle Modeling of Water Distribution Systems : Application of Model View Definition...2013 Ontology for Life-Cycle Modeling of Water Distribution Systems : Application of Model View Definition Attributes Kristine K. Fallon, Robert A...interior plumbing systems and the information exchange requirements for every participant in the design. The findings were used to develop an

A Holistic Approach to Systems Development

NASA Technical Reports Server (NTRS)

Wong, Douglas T.

2008-01-01

Introduces a Holistic and Iterative Design Process. Continuous process but can be loosely divided into four stages. More effort spent early on in the design. Human-centered and Multidisciplinary. Emphasis on Life-Cycle Cost. Extensive use of modeling, simulation, mockups, human subjects, and proven technologies. Human-centered design doesn t mean the human factors discipline is the most important Disciplines should be involved in the design: Subsystem vendors, configuration management, operations research, manufacturing engineering, simulation/modeling, cost engineering, hardware engineering, software engineering, test and evaluation, human factors, electromagnetic compatibility, integrated logistics support, reliability/maintainability/availability, safety engineering, test equipment, training systems, design-to-cost, life cycle cost, application engineering etc. 9

Sourcing Lifecycle for Software as a Service (SAAS)

NASA Astrophysics Data System (ADS)

Santy; Sikkel, K.

2014-03-01

In recent years, Software as a Service (SaaS) has changed from curiosity caused concept to an accepted well known concept. A key advantage of this model is that, by cautious engineering, it is possible to influence economy of scale to decrease total cost of ownership compared to on-premises solutions. By using the guideline elaborated in this paper, companies which has interest in implementing SaaS will be led throughout the entire implementation cycle starting before the company decides to implement SaaS until the stage when the company decides to shift from SaaS model to another model or when they shift to another SaaS company

A life cycle model of public policy issues in health care: the importance of strategic issues management.

PubMed

Rakich, J S; Feit, M D

2001-01-01

Public policy affects health and social services organizations. Senior management has a responsibility to prevent inappropriate demands of stakeholders from predominating and to influence the outcome of public policy to the benefit of their organization through the strategic issues management process. This article presents a public policy issue life cycle model, life-cycle stages and suggested strategies, paths issues can take in the life cycle, and factors that affect issue paths. An understanding of these dynamics can aid senior managers in shaping and changing public policy issues and lessening external environment threats to their organization.

Identification of in vivo regulators of the Vibrio cholerae xds gene using a high-throughput genetic selection.

PubMed

McDonough, Emilykate; Lazinski, David W; Camilli, Andrew

2014-04-01

Vibrio cholerae, the causative agent of cholera, remains a threat to public health in areas with inadequate sanitation. As a waterborne pathogen, V. cholerae moves between two dissimilar environments, aquatic reservoirs and the intestinal tract of humans. Accordingly, this pathogen undergoes adaptive shifts in gene expression throughout the different stages of its lifecycle. One particular gene, xds, encodes a secreted exonuclease that was previously identified as being induced during infection. Here we sought to identify regulators responsible for the in vivo-specific induction of xds. A transcriptional fusion of xds to two consecutive antibiotic resistance genes was used to select transposon mutants that had inserted within or adjacent to regulatory genes and thereby caused increased expression of the xds fusion under non-inducing conditions. Large pools of selected insertion sites were sequenced in a high throughput manner using Tn-seq to identify potential mechanisms of xds regulation. Our selection identified the two-component system PhoB/R as the dominant activator of xds expression. In vitro validation confirmed that PhoB, a protein which is only active during phosphate limitation, was responsible for xds activation. Using xds expression as a biosensor of the extracellular phosphate level, we observed that the mouse small intestine is a phosphate-limited environment. © 2014 John Wiley & Sons Ltd.

Promoting Model-based Definition to Establish a Complete Product Definition

PubMed Central

Ruemler, Shawn P.; Zimmerman, Kyle E.; Hartman, Nathan W.; Hedberg, Thomas; Feeny, Allison Barnard

2016-01-01

The manufacturing industry is evolving and starting to use 3D models as the central knowledge artifact for product data and product definition, or what is known as Model-based Definition (MBD). The Model-based Enterprise (MBE) uses MBD as a way to transition away from using traditional paper-based drawings and documentation. As MBD grows in popularity, it is imperative to understand what information is needed in the transition from drawings to models so that models represent all the relevant information needed for processes to continue efficiently. Finding this information can help define what data is common amongst different models in different stages of the lifecycle, which could help establish a Common Information Model. The Common Information Model is a source that contains common information from domain specific elements amongst different aspects of the lifecycle. To help establish this Common Information Model, information about how models are used in industry within different workflows needs to be understood. To retrieve this information, a survey mechanism was administered to industry professionals from various sectors. Based on the results of the survey a Common Information Model could not be established. However, the results gave great insight that will help in further investigation of the Common Information Model. PMID:28070155

Margalef's mandala and phytoplankton bloom strategies

NASA Astrophysics Data System (ADS)

Wyatt, Timothy

2014-03-01

Margalef's mandala maps phytoplankton species into a phase space defined by turbulence (A) and nutrient concentrations (Ni); these are the hard axes. The permutations of high and low A and high and low Ni divide the space into four domains. Soft axes indicate some ecological dynamics. A main sequence shows the normal course of phytoplankton succession; the r-K axis of MacArthur and Wilson runs parallel to it. An alternative successional sequence leads to the low A-high Ni domain into which many red tide species are mapped. Astronomical and biological time are implicit. A mathematical transformation of the mandala (rotation) links it to the classical bloom models of Sverdrup (time) and Kierstead and Slobodkin (space). Both rarity and the propensity to form red tides are considered to be species characters, meaning that maximum population abundance can be a target of natural selection. Equally, both the unpredictable appearance of bloom species and their short-lived appearances may be species characters. There may be a correlation too between these features and long-lived dormant stages in the life-cycle; then the vegetative planktonic phase is the 'weak link' in the life-cycle. Red tides are thus due to species which have evolved suites of traits which result in specific demographic strategies.

Sustainable Materials Management (SMM) WasteWise Data

EPA Pesticide Factsheets

EPA??s WasteWise encourages organizations and businesses to achieve sustainability in their practices and reduce select industrial wastes. WasteWise is part of EPA??s sustainable materials management efforts, which promote the use and reuse of materials more productively over their entire lifecycles. All U.S. businesses, governments and nonprofit organizations can join WasteWise as a partner, endorser or both. Current participants range from small local governments and nonprofit organizations to large multinational corporations. Partners demonstrate how they reduce waste, practice environmental stewardship and incorporate sustainable materials management into their waste-handling processes. Endorsers promote enrollment in WasteWise as part of a comprehensive approach to help their stakeholders realize the economic benefits to reducing waste. WasteWise helps organizations reduce their impact on global climate change through waste reduction. Every stage of a product's life cycle??extraction, manufacturing, distribution, use and disposal??indirectly or directly contributes to the concentration of greenhouse gases (GHGs) in the atmosphere and affects the global climate. WasteWise is part of EPA's larger SMM program (https://www.epa.gov/smm). Sustainable Materials Management (SMM) is a systemic approach to using and reusing materials more productively over their entire lifecycles. It represents a change in how our society thinks about the use of natural resources

Dynamical Influence and Operational Impacts of an Extreme Mediterranean Cold Surge

DTIC Science & Technology

2013-06-01

over 45 cm of snowfall in Souda Bay, Crete, which significantly impacted operations at Naval Support Activity Souda Bay. The extratropical wave...cold surge event and its dependence on the upstream synoptic scale events. 14. SUBJECT TERMS Extratropical Cyclone, Souda Bay...Activity Souda Bay. The extratropical wave associated with the cold surge could be classified as a classic life-cycle 1 wave break. The wave-breaking

A Cost-Reduction Strategy for Weapon System Acquisition

DTIC Science & Technology

1990-12-01

quantities, manufacturing processes, and test and evaluation are made. As a result, by milestone I, approximately 60% of the life-cycle costs are already...Assess the results from the potential SDIO application of the CRS and 5 consider further development and testing of the strategy. - Consider a policy that...eliminating activities must be carefully weighed. For example, extensive testing and I program reviews are typically classified as non-value added activities

Risk management in the North sea offshore industry: History, status and challenges

NASA Astrophysics Data System (ADS)

Smith, E. J.

1995-10-01

There have been major changes in the UK and Norwegian offshore safety regimes in the last decade. On the basis of accumulated experience (including some major accidents), there has been a move away from a rigid, prescriptive approach to setting safety standards; it is now recognised that a more flexible, "goal-setting" approach is more suited to achieving cost-effective solutions to offshore safety. In order to adapt to this approach, offshore operators are increasingly using Quantitative Risk Assessment (QRA) techniques as part of their risk management programmes. Structured risk assessment can be used at all stages of a project life-cycle. In the design stages (concept and detailed design), these techniques are valuable tools in ensuring that money is wisely spent on safety-related systems. In the operational stage, QRA can aid the development of procedures. High quality Safety Management Systems (SMSs), covering issues such as training, inspection, and emergency planning, are crucial to maintain "asdesigned" levels of safety and reliability. Audits of SMSs should be carried out all through the operational phase to ensure that risky conditions do not accumulate.

Landscape ecological security response to land use change in the tidal flat reclamation zone, China.

PubMed

Zhang, Runsen; Pu, Lijie; Li, Jianguo; Zhang, Jing; Xu, Yan

2016-01-01

As coastal development becomes a national strategy in Eastern China, land use and landscape patterns have been affected by reclamation projects. In this study, taking Rudong County, China as a typical area, we analyzed land use change and its landscape ecological security responses in the tidal flat reclamation zone. The results show that land use change in the tidal flat reclamation zone is characterized by the replacement of natural tidal flat with agricultural and construction land, which has also led to a big change in landscape patterns. We built a landscape ecological security evaluation system, which consists of landscape interference degree and landscape fragile degree, and then calculated the landscape ecological security change in the tidal flat reclamation zone from 1990 to 2008 to depict the life cycle in tidal flat reclamation. Landscape ecological security exhibited a W-shaped periodicity, including the juvenile stage, growth stage, and maturation stage. Life-cycle analysis demonstrates that 37 years is required for the land use system to transform from a natural ecosystem to an artificial ecosystem in the tidal flat reclamation zone.

Model Based Definition

NASA Technical Reports Server (NTRS)

Rowe, Sidney E.

2010-01-01

In September 2007, the Engineering Directorate at the Marshall Space Flight Center (MSFC) created the Design System Focus Team (DSFT). MSFC was responsible for the in-house design and development of the Ares 1 Upper Stage and the Engineering Directorate was preparing to deploy a new electronic Configuration Management and Data Management System with the Design Data Management System (DDMS) based upon a Commercial Off The Shelf (COTS) Product Data Management (PDM) System. The DSFT was to establish standardized CAD practices and a new data life cycle for design data. Of special interest here, the design teams were to implement Model Based Definition (MBD) in support of the Upper Stage manufacturing contract. It is noted that this MBD does use partially dimensioned drawings for auxiliary information to the model. The design data lifecycle implemented several new release states to be used prior to formal release that allowed the models to move through a flow of progressive maturity. The DSFT identified some 17 Lessons Learned as outcomes of the standards development, pathfinder deployments and initial application to the Upper Stage design completion. Some of the high value examples are reviewed.

AESA diagnostics in operational environments

NASA Astrophysics Data System (ADS)

Hull, W. P.

The author discusses some possible solutions to ASEA (active electronically scanned array) diagnostics in the operational environment using built-in testing (BIT), which can play a key role in reducing life-cycle cost if accurately implemented. He notes that it is highly desirable to detect and correct in the operational environment all degradation that impairs mission performance. This degradation must be detected with low false alarm rate and the appropriate action initiated consistent with low life-cycle cost. Mutual coupling is considered as a BIT signal injection method and is shown to have potential. However, the limits of the diagnostic capability using this method clearly depend on its stability and on the level of multipath for a specific application. BIT using mutual coupling may need to be supplemented on the ground by an externally mounted passive antenna that interfaces with onboard avionics.

Nurturing the brain nutritionally and emotionally from before conception to late adolescence.

PubMed

House, Simon H

2007-01-01

Sound nurture requires skills concerning nutrition and emotions, skills that are particularly important in key stages relating to brain development. We are recognizing more clearly the way that serious changes from our hunter-gatherer waterside lifestyle are affecting both our diet and our emotional relationships: first the changes a few hundred generations ago in the agricultural revolution: and more recently in the industrial revolution. These effects have been aggravated in the last century by excessively profit-driven intensive farming, and recently by intensive food-marketing--particularly to children. People are gradually becoming aware how very susceptible is the most vulnerable stage of the lifecycle, the reproductive phase. From long before fertilization and conception, parental nutrition affects a person's development and health for life. Controlled trials show marked effects of nurture on the brain's subsequent acuity. Brain structure throughout development has become visible through modern scans, and also brain activity and mental response. The neural tube, forming at around 3 weeks, if undernourished may be inadequately sealed and demarcated, leading to incomplete interconnection between brain regions. Results vary, but can emanate as: autism or attention-deficit/hyperactivity-disorder (AD/HD); difficulty with relationships and social sense; poor self-control, with risk of violence. Evidence indicates that over 80% of current reproductive hazards, including infertility and malformations, might be prevented purely by sound all-round nurture. Between the embryonic stage and adulthood the brain makes several developmental spurts. Particularly during these spurts, sound nutrition and activity help the brain reach its full genetic potential for capacity, acuity, and connections between regions. From the beginning, hormones and nutrients, or their deficits, are setting gene-switches for life. Good bonding and feeding sets gene-switches positively; shock, stress or poor nutrition, negatively. Forceps delivery combined with serious early separation, correlates with over 4 times the risk of criminal violence by the age of 18. So disruptions of nurture set at risk not only body and brain but a person's very spirituality. Understanding of the biochemistry and epigenetics highlights our urgent need to learn from our evolutionary ways, not only of childbearing, but of a physically active life nourished by foods from the water and the wild.

401(k) plan asset allocation, account balances, and loan activity in 2008.

PubMed

VanDerhei, Jack; Holden, Sarah; Alonso, Luis

2009-10-01

Because 401(k) balances can fluctuate with market returns from year to year, meaningful analysis of 401(k) plans must examine how participants' accounts have performed over the long term. Looking at consistent participants in the EBRI/ICI 401(k) database over the five-year period from 2003 to 2008 (which included one of the worst bear markets for stocks since the Great Depression), the study found: After rising in 2003 and for the next four consecutive years, the average 401(k) retirement account fell 24.3 percent in 2008. The average 401(k) account balance moved up and down with stock market performance, but over the entire five-year time period increased at an average annual growth rate of 7.2 percent, attaining $86,513 at year-end 2008. The median (mid-point) 401(k) account balance increased at an average annual growth rate of 11.4 percent over the 2003-2008 period to $43,700 at year-end 2008. THE BULK OF 401(K) ASSETS CONTINUED TO BE INVESTED IN STOCKS. On average, at year-end 2008, 56 percent of 401(k) participants' assets were invested in equity securities through equity funds, the equity portion of balanced funds, and company stock. Forty-one percent was in fixed-income securities such as stable-value investments and bond and money market funds. THREE-QUARTERS OF 401(K) PLANS INCLUDED LIFECYCLE FUNDS IN THEIR INVESTMENT LINEUP AT YEAR-END 2008. At year-end 2008, nearly 7 percent of the assets in the EBRI/ICI 401(k) database were invested in lifecycle funds and 31 percent of 401(k) participants held lifecycle funds. Also known as "target-date" funds, they are designed to simplify investing and automate account rebalancing. NEW EMPLOYEES CONTINUED TO USE BALANCED FUNDS, INCLUDING LIFECYCLE FUNDS. Across all age groups, more new or recent hires invested their 401(k) assets in balanced funds, including lifecycle funds. At year-end 2008, 36 percent of the account balances of recently hired participants in their 20s were invested in balanced funds, compared with 28 percent in 2007, and about 7 percent in 1998. At year-end 2008, almost 23 percent of the account balances of recently hired participants in their 20s were invested in lifecycle funds, compared with almost 19 percent at year-end 2007. 401(K) PARTICIPANTS CONTINUED TO SEEK DIVERSIFICATION OF THEIR INVESTMENTS. The share of 401(k) accounts invested in company stock continued to shrink, falling by nearly 1 percentage point (to 9.7 percent) in 2008. That continued a steady decline that started in 1999. Recently hired 401(k) participants contributed to this trend: they were less likely to hold employer stock. PARTICIPANTS' 401(K) LOAN ACTIVITY WAS STABLE. In 2008, 18 percent of all 401(k) participants eligible for loans had a loan outstanding against their 401(k) account, the same percentage as at year-end 2007 and year-end 2006. Loans outstanding amounted to 16 percent of the remaining account balance, on average, at year-end 2008; this is similar to the year-end 2002 level.

EPO Program and Product Evaluation Throughout the Development Lifecycle

NASA Astrophysics Data System (ADS)

Kaiser, C.; Butcher, G. J.

2013-12-01

Evaluation of successful education and public outreach (EPO) programs and products is becoming increasingly important for the continued development of such efforts. This presentation will detail the tools and techniques used to evaluate two EPO efforts- 1) NASA's REEL Science Communications Contest and Video Production Workshop, and 2) the 'Sensors, Circuits, and Satellites' product. A primary challenge with evaluating any EPO product geared towards children and students is the limitation on collecting information from minors. With regards to the REEL Science Contest, over 120 students participated in producing and entering 48 contest entries but because of the Office of Budget and Management (OBM) regulations that restrict collecting feedback from more than nine individuals, we were only able to collect evaluation data from a small subset of this group. The five winning students who participated in the final workshop took part in the evaluation. The benefit of a small group size is that it allowed for more in-depth one-on-one interviews with each student. The feedback collected from this evaluation offered valuable insight into what worked well along with areas of improvement for futures contests and workshops. The REEL Science video contest had another evaluation opportunity since NASA scientists, communications experts, and producers also participated in the program and worked directly with the students. A survey was administered for this audience in an effort to gauge the perceived value and success of the program from the perspective of the originating institution. We found that if a program is well received, the program is more likely to receive future support. Additionally, this component of the program evaluation provided useful feedback and lessons learned to help optimize the role of the internal audience for similar programs in the future. Implementing formative evaluation is key to developing a successful EPO product development. Collecting data at key stages during development allows for modifications and improvements to the product before time and money have been wasted going down the wrong path. Depending on the product and the stage of development, there are several evaluation tools to employ: surveys, observations, expert analysis, heuristic evaluations, feedback forms, diary studies, use case testing and interviews. In the case of developing the 'Sensors, Circuits, and Satellites' product, surveys were collected from teachers and students who participated in the lesson or activity. Audio recordings were also made of the teachers as they completed each activity to collect direct quotes, questions, concerns, and feedback. Facilitators completed feedback forms to capture quotes and observations of the students working through the activities and engaging with the product. All of these data provided valuable insight into the participants' experiences and effectiveness of the product. A complement of tools and techniques is the best approach to evaluating EPO products and programs. These will vary based on application, but can easily be implemented at key points in the development lifecycle to produce feedback and data used to assess and meet EPO goals and objectives.

77 FR 65665 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-30

...: International Trade Administration. Title: International Client Life-cycle Multi-Purpose Forms. OMB Control... of an international client's life-cycle with CS, involves merging with other information collections...

Engineering Knowledge for Assistive Living

NASA Astrophysics Data System (ADS)

Chen, Liming; Nugent, Chris

This paper introduces a knowledge based approach to assistive living in smart homes. It proposes a system architecture that makes use of knowledge in the lifecycle of assistive living. The paper describes ontology based knowledge engineering practices and discusses mechanisms for exploiting knowledge for activity recognition and assistance. It presents system implementation and experiments, and discusses initial results.

New Roles for New Times: Digital Curation for Preservation

ERIC Educational Resources Information Center

Walters, Tyler; Skinner, Katherine

2011-01-01

Digital curation refers to the actions people take to maintain and add value to digital information over its lifecycle, including the processes used when creating digital content. Digital preservation focuses on the "series of managed activities necessary to ensure continued access to digital materials for as long as necessary." In this…

Body composition throughout the lifecycle: The role of dairy foods

USDA-ARS?s Scientific Manuscript database

There is an ongoing concern about the degree of obesity world-wide and the implications for health outcomes. Body mass index (BMI) is used as the measure for the classification of overweight and obesity. However, this index does not represent actual body fat levels or the amount of active lean bod...

THE EMERGING FOCUS ON LIFE-CYCLE ASSESSMENT IN THE U. S. ENVIRONMENTAL PROTECTION AGENCY

EPA Science Inventory

EPA has been actively engaged in LCA research since 1990 to help advance the methodology and application of life cycle thinking in decision-making. Across the Agency consideration of the life cycle concept is increasing in the development of policies and programs. A major force i...

Effects of methyltestosterone, letrozole, triphenyltin and fenarimol on histology of reproductive organs of the copepod Acartia tonsa.

PubMed

Watermann, Burkard T; Albanis, Triantafyllos A; Dagnac, Thierry; Gnass, Katarina; Ole Kusk, K; Sakkas, Vasilios A; Wollenberger, Leah

2013-07-01

The marine calanoid copepod Acartia tonsa was exposed to methyltestosterone (MET, 1.6-126 μg L(-1)), letrozole (LET, 10-1000 μg L(-1)), triphenyltin chloride (TPT, 0.0014-0.0088 μg L(-1) TPT-Sn) and fenarimol (FEN, 2.8-105 μg L(-1)) for 21 d covering a full life-cycle. All four compounds investigated are known to act as androgens in vertebrates. The digestive tract, musculature, nervous system, reproductive organs, gonad and accessory sexual glands were examined by light microscopy after routine staining and immune-labelling for detection of apoptosis and determination of proliferation activities. MET induced an inhibition of oogenesis, oocyte maturation and yolk formation, respectively, which was most pronounced at the lowest concentrations tested. In LET exposed males, spermatogenesis was enhanced with very prominent gamete stages; in some stages apoptosis occurred. The spermatophore was hypertrophied and displayed deformations. In females, LET induced a disorder of oogenesis and disturbances in yolk synthesis. TPT stimulated the male reproductive system at 0.0014 and 0.0035 μg TPT-SnL(-1), whereas inhibiting effects were observed in the female gonad at 0.0088 μg TPT-SnL(-1). In FEN exposed females proliferation of gametes was reduced and yolk formation showed irregular features at 2.8-105 μgL(-1). In FEN exposed males an elevated proliferation activity was observed. No pathological alterations in other organ systems, e.g. the digestive tract including the hindgut acting as respiratory organ, the nervous system, or the musculature were seen. This indicates that the effects on gonads might be caused rather by disturbance of endocrine signalling or interference with hormone metabolism than by general toxicity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Life-cycle energy impacts for adapting an urban water supply system to droughts.

PubMed

Lam, Ka Leung; Stokes-Draut, Jennifer R; Horvath, Arpad; Lane, Joe L; Kenway, Steven J; Lant, Paul A

2017-12-15

In recent years, cities in some water stressed regions have explored alternative water sources such as seawater desalination and potable water recycling in spite of concerns over increasing energy consumption. In this study, we evaluate the current and future life-cycle energy impacts of four alternative water supply strategies introduced during a decade-long drought in South East Queensland (SEQ), Australia. These strategies were: seawater desalination, indirect potable water recycling, network integration, and rainwater tanks. Our work highlights the energy burden of alternative water supply strategies which added approximately 24% life-cycle energy use to the existing supply system (with surface water sources) in SEQ even for a current post-drought low utilisation status. Over half of this additional life-cycle energy use was from the centralised alternative supply strategies. Rainwater tanks contributed an estimated 3% to regional water supply, but added over 10% life-cycle energy use to the existing system. In the future scenario analysis, we compare the life-cycle energy use between "Normal", "Dry", "High water demand" and "Design capacity" scenarios. In the "Normal" scenario, a long-term low utilisation of the desalination system and the water recycling system has greatly reduced the energy burden of these centralised strategies to only 13%. In contrast, higher utilisation in the unlikely "Dry" and "Design capacity" scenarios add 86% and 140% to life-cycle energy use of the existing system respectively. In the "High water demand" scenario, a 20% increase in per capita water use over 20 years "consumes" more energy than is used by the four alternative strategies in the "Normal" scenario. This research provides insight for developing more realistic long-term scenarios to evaluate and compare life-cycle energy impacts of drought-adaptation infrastructure and regional decentralised water sources. Scenario building for life-cycle assessments of water supply systems should consider i) climate variability and, therefore, infrastructure utilisation rate, ii) potential under-utilisation for both installed centralised and decentralised sources, and iii) the potential energy penalty for operating infrastructure well below its design capacity (e.g., the operational energy intensity of the desalination system is three times higher at low utilisation rates). This study illustrates that evaluating the life-cycle energy use and intensity of these type of supply sources without considering their realistic long-term operating scenario(s) can potentially distort and overemphasise their energy implications. To other water stressed regions, this work shows that managing long-term water demand is also important, in addition to acknowledging the energy-intensive nature of some alternative water sources. Copyright © 2017 Elsevier Ltd. All rights reserved.

Small-molecule histone methyltransferase inhibitors display rapid antimalarial activity against all blood stage forms in Plasmodium falciparum

PubMed Central

Malmquist, Nicholas A.; Moss, Thomas A.; Mecheri, Salah; Scherf, Artur; Fuchter, Matthew J.

2012-01-01

Epigenetic factors such as histone methylation control the developmental progression of malaria parasites during the complex life cycle in the human host. We investigated Plasmodium falciparum histone lysine methyltransferases as a potential target class for the development of novel antimalarials. We synthesized a compound library based upon a known specific inhibitor (BIX-01294) of the human G9a histone methyltransferase. Two compounds, BIX-01294 and its derivative TM2-115, inhibited P. falciparum 3D7 parasites in culture with IC50 values of ∼100 nM, values at least 22-fold more potent than their apparent IC50 toward two human cell lines and one mouse cell line. These compounds irreversibly arrested parasite growth at all stages of the intraerythrocytic life cycle. Decrease in parasite viability (>40%) was seen after a 3-h incubation with 1 µM BIX-01294 and resulted in complete parasite killing after a 12-h incubation. Additionally, mice with patent Plasmodium berghei ANKA strain infection treated with a single dose (40 mg/kg) of TM2-115 had 18-fold reduced parasitemia the following day. Importantly, treatment of P. falciparum parasites in culture with BIX-01294 or TM2-115 resulted in significant reductions in histone H3K4me3 levels in a concentration-dependent and exposure time-dependent manner. Together, these results suggest that BIX-01294 and TM2-115 inhibit malaria parasite histone methyltransferases, resulting in rapid and irreversible parasite death. Our data position histone lysine methyltransferases as a previously unrecognized target class, and BIX-01294 as a promising lead compound, in a presently unexploited avenue for antimalarial drug discovery targeting multiple life-cycle stages. PMID:23011794

Exploring business process modelling paradigms and design-time to run-time transitions

NASA Astrophysics Data System (ADS)

Caron, Filip; Vanthienen, Jan

2016-09-01

The business process management literature describes a multitude of approaches (e.g. imperative, declarative or event-driven) that each result in a different mix of process flexibility, compliance, effectiveness and efficiency. Although the use of a single approach over the process lifecycle is often assumed, transitions between approaches at different phases in the process lifecycle may also be considered. This article explores several business process strategies by analysing the approaches at different phases in the process lifecycle as well as the various transitions.

Life-cycle environmental performance of renewable building materials in the context of residential construction : phase II research report : an extension to the 2005 phase I research report. Module N, Life-cycle inventory of manufacturing prefinished engineered wood flooring in the eastern United States

Treesearch

Richard D. Bergman; Scott A. Bowe

2011-01-01

This study summarizes the environmental performance of prefinished engineered wood flooring using life-cycle inventory (LCI) analysis. Using primary mill data gathered from manufacturers in the eastern United States and applying the methods found in Consortium for Research on Renewable Industrial Materials (CORRIM) Research Guidelines and International Organization of...

An Agile Systems Engineering Process: The Missing Link?

DTIC Science & Technology

2011-05-01

has a num- ber of standards available such as ISO 12207 , ISO 9001 and the Capability Maturity Model Integrated (CMMI®) [24,25,26]. The CMMI was a...addressing activities throughout the products lifecycle [24]. ISO 12207 “contains processes, activities and tasks that are to be applied during...the acquisition of a system that contains software” [26]. A limitation identified within ISO 12207 is that it does not specify details on how to

A dynamic population model to investigate effects of climate and climate-independent factors on the lifecycle of the tick Amblyomma americanum (Acari: Ixodidae)

USGS Publications Warehouse

Ludwig, Antoinette; Ginsberg, Howard; Hickling, Graham J.; Ogden, Nicholas H.

2016-01-01

The lone star tick, Amblyomma americanum, is a disease vector of significance for human and animal health throughout much of the eastern United States. To model the potential effects of climate change on this tick, a better understanding is needed of the relative roles of temperature-dependent and temperature-independent (day-length-dependent behavioral or morphogenetic diapause) processes acting on the tick lifecycle. In this study, we explored the roles of these processes by simulating seasonal activity patterns using models with site-specific temperature and day-length-dependent processes. We first modeled the transitions from engorged larvae to feeding nymphs, engorged nymphs to feeding adults, and engorged adult females to feeding larvae. The simulated seasonal patterns were compared against field observations at three locations in United States. Simulations suggested that 1) during the larva-to-nymph transition, some larvae undergo no diapause while others undergo morphogenetic diapause of engorged larvae; 2) molted adults undergo behavioral diapause during the transition from nymph-to-adult; and 3) there is no diapause during the adult-to-larva transition. A model constructed to simulate the full lifecycle of A. americanum successfully predicted observed tick activity at the three U.S. study locations. Some differences between observed and simulated seasonality patterns were observed, however, identifying the need for research to refine some model parameters. In simulations run using temperature data for Montreal, deterministic die-out of A. americanum populations did not occur, suggesting the possibility that current climate in parts of southern Canada is suitable for survival and reproduction of this tick.

A Dynamic Population Model to Investigate Effects of Climate and Climate-Independent Factors on the Lifecycle of Amblyomma americanum (Acari: Ixodidae).

PubMed

Ludwig, Antoinette; Ginsberg, Howard S; Hickling, Graham J; Ogden, Nicholas H

2016-01-01

The lone star tick, Amblyomma americanum, is a disease vector of significance for human and animal health throughout much of the eastern United States. To model the potential effects of climate change on this tick, a better understanding is needed of the relative roles of temperature-dependent and temperature-independent (day-length-dependent behavioral or morphogenetic diapause) processes acting on the tick lifecycle. In this study, we explored the roles of these processes by simulating seasonal activity patterns using models with site-specific temperature and day-length-dependent processes. We first modeled the transitions from engorged larvae to feeding nymphs, engorged nymphs to feeding adults, and engorged adult females to feeding larvae. The simulated seasonal patterns were compared against field observations at three locations in United States. Simulations suggested that 1) during the larva-to-nymph transition, some larvae undergo no diapause while others undergo morphogenetic diapause of engorged larvae; 2) molted adults undergo behavioral diapause during the transition from nymph-to-adult; and 3) there is no diapause during the adult-to-larva transition. A model constructed to simulate the full lifecycle of A. americanum successfully predicted observed tick activity at the three U.S. study locations. Some differences between observed and simulated seasonality patterns were observed, however, identifying the need for research to refine some model parameters. In simulations run using temperature data for Montreal, deterministic die-out of A. americanum populations did not occur, suggesting the possibility that current climate in parts of southern Canada is suitable for survival and reproduction of this tick. © Crown copyright 2015.

49 CFR 236.917 - Retention of records.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-Based Signal and Train Control Systems § 236.917 Retention of records. (a) What life-cycle and...: (i) For the life-cycle of the product, adequate documentation to demonstrate that the PSP meets the...

49 CFR 236.917 - Retention of records.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-Based Signal and Train Control Systems § 236.917 Retention of records. (a) What life-cycle and...: (i) For the life-cycle of the product, adequate documentation to demonstrate that the PSP meets the...

Life-cycle assessment of Nebraska bridges.

DOT National Transportation Integrated Search

2013-05-01

Life-cycle cost analysis (LCCA) is a necessary component in bridge management systems (BMSs) for : assessing investment decisions and identifying the most cost-effective improvement alternatives. The : LCCA helps to identify the lowest cost alternati...

Life-cycle costing: Practical considerations

NASA Technical Reports Server (NTRS)

Eisenberger, I.; Lorden, G.

1977-01-01

The history and methodology of life-cycle costing are presented and analyzed, contrasting the potential benefits of the technique with the difficulties of its application. Examples and a short survey of the literature are given.

A Collaborative Approach to Lifecycle Management: An Engineering Perspective

NASA Technical Reports Server (NTRS)

Cooper, L. P.; Spellman, K.

1998-01-01

In this paper, we will discuss how the partnership formed between the engineering and archival disciplines at the Jet Propulsion Laboratory (JPL) is working to improve lifecycle management for all users.

Simplified Life-Cycle Cost Estimation

NASA Technical Reports Server (NTRS)

Remer, D. S.; Lorden, G.; Eisenberger, I.

1983-01-01

Simple method for life-cycle cost (LCC) estimation avoids pitfalls inherent in formulations requiring separate estimates of inflation and interest rates. Method depends for validity observation that interest and inflation rates closely track each other.

Planning for Cost Effectiveness.

ERIC Educational Resources Information Center

Schlaebitz, William D.

1984-01-01

A heat pump life-cycle cost analysis is used to explain the technique. Items suggested for the life-cycle analysis approach include lighting, longer-life batteries, site maintenance, and retaining experts to inspect specific building components. (MLF)

Productive Lifecycle of Human Papillomaviruses that Depends Upon Squamous Epithelial Differentiation

PubMed Central

Kajitani, Naoko; Satsuka, Ayano; Kawate, Akifumi; Sakai, Hiroyuki

2012-01-01

Human papillomaviruses (HPVs) target the stratified epidermis, and can causes diseases ranging from benign condylomas to malignant tumors. Infections of HPVs in the genital tract are among the most common sexually transmitted diseases, and a major risk factor for cervical cancer. The virus targets epithelial cells in the basal layer of the epithelium, while progeny virions egress from terminally differentiated cells in the cornified layer, the surface layer of the epithelium. In infected basal cells, the virus maintains its genomic DNA at low-copy numbers, at which the viral productive lifecycle cannot proceed. Progression of the productive lifecycle requires differentiation of the host cell, indicating that there is tight crosstalk between viral replication and host differentiation programs. In this review, we discuss the regulation of the HPV lifecycle controlled by the differentiation program of the host cells. PMID:22536200

Consideration of black carbon and primary organic carbon emissions in life-cycle analysis of Greenhouse gas emissions of vehicle systems and fuels.

PubMed

Cai, Hao; Wang, Michael Q

2014-10-21

The climate impact assessment of vehicle/fuel systems may be incomplete without considering short-lived climate forcers of black carbon (BC) and primary organic carbon (POC). We quantified life-cycle BC and POC emissions of a large variety of vehicle/fuel systems with an expanded Greenhouse gases, Regulated Emissions, and Energy use in Transportation model developed at Argonne National Laboratory. Life-cycle BC and POC emissions have small impacts on life-cycle greenhouse gas (GHG) emissions of gasoline, diesel, and other fuel vehicles, but would add 34, 16, and 16 g CO2 equivalent (CO2e)/mile, or 125, 56, and 56 g CO2e/mile with the 100 or 20 year Global Warming Potentials of BC and POC emissions, respectively, for vehicles fueled with corn stover-, willow tree-, and Brazilian sugarcane-derived ethanol, mostly due to BC- and POC-intensive biomass-fired boilers in cellulosic and sugarcane ethanol plants for steam and electricity production, biomass open burning in sugarcane fields, and diesel-powered agricultural equipment for biomass feedstock production/harvest. As a result, life-cycle GHG emission reduction potentials of these ethanol types, though still significant, are reduced from those without considering BC and POC emissions. These findings, together with a newly expanded GREET version, help quantify the previously unknown impacts of BC and POC emissions on life-cycle GHG emissions of U.S. vehicle/fuel systems.

A Circadian Clock Gene, Cry, Affects Heart Morphogenesis and Function in Drosophila as Revealed by Optical Coherence Microscopy

PubMed Central

Zeng, Xianxu; Tate, Rebecca E.; McKee, Mary L.; Capen, Diane E.; Zhang, Zhan; Tanzi, Rudolph E.; Zhou, Chao

2015-01-01

Circadian rhythms are endogenous, entrainable oscillations of physical, mental and behavioural processes in response to local environmental cues such as daylight, which are present in the living beings, including humans. Circadian rhythms have been related to cardiovascular function and pathology. However, the role that circadian clock genes play in heart development and function in a whole animal in vivo are poorly understood. The Drosophila cryptochrome (dCry) is a circadian clock gene that encodes a major component of the circadian clock negative feedback loop. Compared to the embryonic stage, the relative expression levels of dCry showed a significant increase (>100-fold) in Drosophila during the pupa and adult stages. In this study, we utilized an ultrahigh resolution optical coherence microscopy (OCM) system to perform non-invasive and longitudinal analysis of functional and morphological changes in the Drosophila heart throughout its post-embryonic lifecycle for the first time. The Drosophila heart exhibited major morphological and functional alterations during its development. Notably, heart rate (HR) and cardiac activity period (CAP) of Drosophila showed significant variations during the pupa stage, when heart remodeling took place. From the M-mode (2D + time) OCM images, cardiac structural and functional parameters of Drosophila at different developmental stages were quantitatively determined. In order to study the functional role of dCry on Drosophila heart development, we silenced dCry by RNAi in the Drosophila heart and mesoderm, and quantitatively measured heart morphology and function in those flies throughout its development. Silencing of dCry resulted in slower HR, reduced CAP, smaller heart chamber size, pupal lethality and disrupted posterior segmentation that was related to increased expression of a posterior compartment protein, wingless. Collectively, our studies provided novel evidence that the circadian clock gene, dCry, plays an essential role in heart morphogenesis and function. PMID:26348211

Life-cycle and growth-phase-dependent regulation of the ubiquitin genes of Trypanosoma cruzi.

PubMed

Manning-Cela, Rebeca; Jaishankar, Sobha; Swindle, John

2006-07-01

Trypanosoma cruzi, the causative agent of Chagas disease, exhibits a complex life cycle that is accompanied by the stage-specific gene expression. At the molecular level, very little is known about gene regulation in trypanosomes. Complex gene organizations coupled with polycistronic transcription units make the analysis of regulated gene expression difficult in trypanosomes. The ubiquitin genes of T. cruzi are a good example of this complexity. They are organized as a single cluster containing five ubiquitin fusion (FUS) and five polyubiquitin (PUB) genes that are polycistronically transcribed but expressed differently in response to developmental and environmental changes. Gene replacements were used to study FUS and PUB gene expression at different stages of growth and at different points in the life cycle of T. cruzi. Based on the levels of reporter gene expression, it was determined that FUS1 expression was downregulated as the parasites approached stationary phase, whereas PUB12.5 polyubiquitin gene expression increased. Conversely, FUS1 expression increases when epimastigotes and amastigotes differentiate into trypomastigotes, whereas the expression of PUB12.5 decreases when epimastigotes differentiate into amastigotes and trypomastigotes. Although the level of CAT activity in logarithmic growing epimastigotes is six- to seven-fold higher when the gene was expressed from the FUS1 locus than when expressed from the PUB12.5 locus, the rate of transcription from the two loci was the same implying that post-transcriptional mechanisms play a dominant role in the regulation of gene expression.

Phylogenetic analysis with multiple markers indicates repeated loss of the adult medusa stage in Campanulariidae (Hydrozoa, Cnidaria).

PubMed

Govindarajan, Annette F; Boero, Ferdinando; Halanych, Kenneth M

2006-03-01

The Campanulariidae is a group of leptomedusan hydroids (Hydrozoa, Cnidaria) that exhibit a diverse array of life cycles ranging from species with a free medusa stage to those with a reduced or absent medusa stage. Perhaps the best-known member of the taxon is Obelia which is often used as a textbook model of hydrozoan life history. However, Obelia medusae have several unique features leading to a hypothesis that Obelia arose, in a saltational fashion, from an ancestor that lacked a medusa, possibly representing an example of a rare evolutionary reversal. To address the evolution of adult sexual stages in Campanulariidae, a molecular phylogenetic approach was employed using two nuclear (18S rDNA and calmodulin) and two mitochondrial (16S rDNA and cytochrome c oxidase subunit I) genes. Prior to the main analysis, we conducted a preliminary analysis of leptomedusan taxa which suggests that Campanulariidae as presently considered needs to be redefined. Campanulariid analyses are consistent with morphological understanding in that three major clades are recovered. However, several recognized genera are not monophyletic calling into question some "diagnostic" features. Furthermore, ancestral states were reconstructed using parsimony, and a sensitivity analysis was conducted to investigate possible evolutionary transitions in life-history stages. The results indicate that life-cycle transitions have occurred multiple times, and that Obelia might be derived from an ancestor with Clytia-like features.

Analysis of the Seismic Performance of Isolated Buildings according to Life-Cycle Cost

PubMed Central

Dang, Yu; Han, Jian-ping; Li, Yong-tao

2015-01-01

This paper proposes an indicator of seismic performance based on life-cycle cost of a building. It is expressed as a ratio of lifetime damage loss to life-cycle cost and determines the seismic performance of isolated buildings. Major factors are considered, including uncertainty in hazard demand and structural capacity, initial costs, and expected loss during earthquakes. Thus, a high indicator value indicates poor building seismic performance. Moreover, random vibration analysis is conducted to measure structural reliability and evaluate the expected loss and life-cycle cost of isolated buildings. The expected loss of an actual, seven-story isolated hospital building is only 37% of that of a fixed-base building. Furthermore, the indicator of the structural seismic performance of the isolated building is much lower in value than that of the structural seismic performance of the fixed-base building. Therefore, isolated buildings are safer and less risky than fixed-base buildings. The indicator based on life-cycle cost assists owners and engineers in making investment decisions in consideration of structural design, construction, and expected loss. It also helps optimize the balance between building reliability and building investment. PMID:25653677

Analysis of the seismic performance of isolated buildings according to life-cycle cost.

PubMed

Dang, Yu; Han, Jian-Ping; Li, Yong-Tao

2015-01-01

This paper proposes an indicator of seismic performance based on life-cycle cost of a building. It is expressed as a ratio of lifetime damage loss to life-cycle cost and determines the seismic performance of isolated buildings. Major factors are considered, including uncertainty in hazard demand and structural capacity, initial costs, and expected loss during earthquakes. Thus, a high indicator value indicates poor building seismic performance. Moreover, random vibration analysis is conducted to measure structural reliability and evaluate the expected loss and life-cycle cost of isolated buildings. The expected loss of an actual, seven-story isolated hospital building is only 37% of that of a fixed-base building. Furthermore, the indicator of the structural seismic performance of the isolated building is much lower in value than that of the structural seismic performance of the fixed-base building. Therefore, isolated buildings are safer and less risky than fixed-base buildings. The indicator based on life-cycle cost assists owners and engineers in making investment decisions in consideration of structural design, construction, and expected loss. It also helps optimize the balance between building reliability and building investment.

Life-cycle environmental inventory of passenger transportation modes in the United States

NASA Astrophysics Data System (ADS)

Chester, Mikhail Vin

To appropriately mitigate environmental impacts from transportation, it is necessary for decision makers to consider the life-cycle energy consumption and emissions associated with each mode. A life-cycle energy, greenhouse gas, and criteria air pollutant emissions inventory is created for the passenger transportation modes of automobiles, urban buses, heavy rail transit, light rail transit, and aircraft in the U.S. Each mode's inventory includes an assessment of vehicles, infrastructure, and fuel components. For each component, analysis is performed for material extraction through use and maintenance in both direct and indirect (supply chain) processes. For each mode's life-cycle components, energy inputs and emission outputs are determined. Energy inputs include electricity and petroleum-based fuels. Emission outputs include greenhouse gases (CO2, CH4, and N2O) and criteria pollutants (CO, SO2, NOx , VOCs, and PM). The inputs and outputs are normalized by vehicle lifetime, vehicle mile traveled, and passenger mile traveled. A consistent system boundary is applied to all modal inventories which captures the entire life-cycle, except for end-of-life. For each modal life-cycle component, both direct and indirect processes are included if possible. A hybrid life-cycle assessment approach is used to estimate the components in the inventories. We find that life-cycle energy inputs and emission outputs increase significantly compared to the vehicle operational phase. Life-cycle energy consumption is 39-56% larger than vehicle operation for autos, 38% for buses, 93-160% for rail, and 19-24% for air systems per passenger mile traveled. Life-cycle greenhouse gas emissions are 47-65% larger than vehicle operation for autos, 43% for buses, 39-150% for rail, and 24-31% for air systems per passenger mile traveled. The energy and greenhouse gas increases are primarily due to vehicle manufacturing and maintenance, infrastructure construction, and fuel production. For criteria air pollutants, life-cycle components often dominate total emissions and can be a magnitude larger than operational counterparts. Per passenger mile traveled, total SO2 emissions (between 350 and 460 mg) are 19-27 times larger than operational emissions as a result of electricity generation in vehicle manufacturing, infrastructure construction, and fuel production. NOx emissions increase 50-73% for automobiles, 24% for buses, 13-1300% for rail, and 19-24% for aircraft. Non-tailpipe VOCs are 27-40% of total automobile, 71-95% of rail, and 51-81% of air total emissions. Infrastructure and parking construction are major components of total PM10 emissions resulting in total emissions over three times larger than operational emissions for autos and even larger for many rail systems and aircraft (the major contributor being emissions from hot-mix asphalt plants and concrete production). Infrastructure construction and operation as well as vehicle manufacturing increase total CO emissions by 5-17 times from tailpipe performance for rail and 3-9 times for air. A case study comparing the environmental performance of metropolitan regions is presented as an application of the inventory results. The San Francisco Bay Area, Chicago, and New York City are evaluated capturing passenger transportation life-cycle energy inputs and greenhouse gas and criteria air pollutant emissions. The regions are compared between off-peak and peak travel as well as personal and public transit. Additionally, healthcare externalities are computed from vehicle emissions. It is estimated that life-cycle energy varies from 6.3 MJ/PMT in the Bay Area to 5.7 MJ/PMT in Chicago and 5.3 MJ/PMT in New York for an average trip. Life-cycle GHG emissions range from 480 g CO2e/PMT in the Bay Area to 440 g CO2e/PMT for Chicago and 410 g CO 2e/PMT in New York. CAP emissions vary depending on the pollutant with differences as large as 25% between regions. Life-cycle CAP emissions are between 11% and 380% larger than their operational counterparts. Peak travel, with typical higher riderships, does not necessarily environmentally outperform off-peak travel due to the large share of auto PMT and less than ideal operating conditions during congestion. The social costs of travel range from ¢51 (in ¢2007) per auto passenger per trip during peak in New York to ¢6 per public transit passenger per trip during peak hours in the Bay Area and New York. Average personal transit costs are around ¢30 while public transit ranges from ¢28 to ¢41. (Abstract shortened by UMI.)

Using SCOR as a Supply Chain Management Framework for Government Agency Contract Requirements

NASA Technical Reports Server (NTRS)

Paxton, Joseph; Tucker, Brian

2010-01-01

This paper will present a model that uses the Supply-Chain Operations Reference (SCOR) model as a foundation for a framework to illustrate the information needed throughout a product lifecycle to support a healthy supply chain management function and the subsequent contract requirements to enable it. It will also show where in the supply chain the information must be extracted. The ongoing case study used to exemplify the model is NASA's (National Aeronautics and Space Administration) Ares I program for human spaceflight. Effective supply chain management and contract requirements are ongoing opportunities for continuous improvement within government agencies, specifically development of systems for human spaceflight operations. Multiple reports from the Government Accountability Office (GAO) reinforce this importance. The SCOR model is a framework for describing a supply chain with process building blocks and business activities. It provides a set of metrics for measuring supply chain performance and best practices for continuously improving. This paper expands the application of the SCOR to also provide the framework for defining information needed from different levels of the supply chain and at different phases of the lifecycle. These needs can be incorporated into contracts to enable more effective supply chain management. Depending on the phase of the lifecycle, effective supply chain management will require involvement from different levels of the organization and different levels of the supply chain.

77 FR 59373 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-27

...: International Trade Administration. Title: Domestic Client Life-cycle Multi-Purpose Forms. OMB Control Number... customized for each CS client, and will cover all aspects of a client's life-cycle with CS, involves merging...

Life-cycle management: a long-term challenge.

PubMed

Newman, Chris

2003-04-01

With some electronics components being withdrawn after only two years, life-cycle management is becoming a key strategic issue for users and manufacturers of electromedical equipment. This article describes some approaches to tackling the challenge.

Increasing transcriptome response of serpins during the ontogenetic stages in the salmon louse Caligus rogercresseyi (Copepoda: Caligidae).

PubMed

Maldonado-Aguayo, W; Gallardo-Escárate, C

2014-06-01

Serine protease inhibitors, or serpins, target serine proteases, and are important regulators of intra- and extracellular proteolysis. For parasite survival, parasite-derived protease inhibitors have been suggested to play essential roles in evading the host's immune system and protecting against exogenous host proteases. The aim of this work was to identify serpins via high throughput transcriptome sequencing and elucidate their potential functions during the lifecycle of the salmon louse Caligus rogercresseyi. Eleven putative, partial serpin sequences in the C. rogercresseyi transcriptome were identified and denoted as Cr-serpins 1 to 11. Comparative analysis of the deduced serpin-like amino acid sequences revealed a highly conserved reactive center loop region. Interestingly, P1 residues suggest putative functions involved with the trypsin/subtilisin, elastase, or subtilisin inhibitors, which evidenced increasing gene expression profiles from the copepodid to adult stage in C. rogercresseyi. Concerning this, Cr-serpin 10 was mainly expressed in the copepodid stage, while Cr-serpins 3, 4, 5, and 11 were mostly expressed in chalimus and adult stages. These results suggest that serpins could be involved in evading the immune response of the host fish. The identification of these serpins furthers the understanding of the immune system in this important ectoparasite species. Copyright © 2014 Elsevier B.V. All rights reserved.

Design Knowledge Management System (DKMS) Beta Test Report

DTIC Science & Technology

1992-11-01

design process. These problems, which include knowledge representation, constraint propagation, model design, and information integration, are...effective delivery of life-cycle engineering knowledge assistance and information to the design/engineering activities. It does not matter whether these...platfomi. 4. Reuse - existing data, information , and knowledge can be reused. 5. Remote Execution -- automatically handles remote execution without

Dataset Lifecycle Policy

NASA Technical Reports Server (NTRS)

Armstrong, Edward; Tauer, Eric

2013-01-01

The presentation focused on describing a new dataset lifecycle policy that the NASA Physical Oceanography DAAC (PO.DAAC) has implemented for its new and current datasets to foster improved stewardship and consistency across its archive. The overarching goal is to implement this dataset lifecycle policy for all new GHRSST GDS2 datasets and bridge the mission statements from the GHRSST Project Office and PO.DAAC to provide the best quality SST data in a cost-effective, efficient manner, preserving its integrity so that it will be available and usable to a wide audience.

Are the Performance Based Logistics Prophets Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based Logistics

DTIC Science & Technology

2013-10-01

Based Logistics Prophets Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based...Using Science or Alchemy to Create Life-Cycle Affordability? Using Theory to Predict the Efficacy of Performance Based Logistics 5a. CONTRACT NUMBER 5b...Are the PBL Prophets Using Science or Alchemy to Create Life Cycle Affordability? 328Defense ARJ, October 2013, Vol. 20 No. 3 : 325–348 Defense

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module C, Life-cycle inventory of hardwood lumber manufacturing in the Northeast and North Central United States.

Treesearch

Richard Bergman; Scott A. Bowe

2008-01-01

The goal of this study was to find the environmental impact of hardwood lumber production through a gate-to-gate Life-Cycle Inventory (LCI) on hardwood sawmills in the northeast and northcentral (NE/NC) United States. Primary mill data was collected per CORRIM Research Guidelines (CORRIM 2001). Life-cycle analysis is beyond the scope of the study.

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module L, Life-cycle inventory of hardwood lumber manufacturing in the Southeastern United States.

Treesearch

Richard D. Bergman; Scott A. Bowe

2010-01-01

The goal of this study was to gain an understanding of the environmental impact of hardwood lumber production through a gate-to-gate life-cycle inventory (LCI) of hardwood sawmills in the Southeastern United States (SE). Primary mill data were collected per Consortium on Research for Renewable Industrial Materials (CORRIM) Research Guidelines. Life-cycle impact...

A re-assessment of species diversity within the 'revolutum' group of Echinostoma Rudolphi, 1809 (Digenea: Echinostomatidae) in Europe.

PubMed

Faltýnková, Anna; Georgieva, Simona; Soldánová, Miroslava; Kostadinova, Aneta

2015-01-01

Species of Echinostoma Rudolphi, 1809 (Digenea: Echinostomatidae) belonging to the 'revolutum' species complex were re-examined based on material gathered in an extensive sampling programme in eight countries in Europe. The morphology of the life-cycle stages was studied in naturally and experimentally infected snail and bird hosts. A review, with an updated synonymy, is presented for six European species, including one new to science, i.e. Echinostoma revolutum (Frölich, 1802) (sensu stricto) (type-species), E. bolschewense (Kotova, 1939), E. miyagawai Ishii, 1932, E. nasincovae n. sp., E. paraulum Dietz, 1909 and Echinostoma sp. IG), and keys to the identification of their cercariae and adults are provided.

The telerobot workstation testbed for the shuttle aft flight deck: A project plan for integrating human factors into system design

NASA Technical Reports Server (NTRS)

Sauerwein, Timothy

1989-01-01

The human factors design process in developing a shuttle orbiter aft flight deck workstation testbed is described. In developing an operator workstation to control various laboratory telerobots, strong elements of human factors engineering and ergonomics are integrated into the design process. The integration of human factors is performed by incorporating user feedback at key stages in the project life-cycle. An operator centered design approach helps insure the system users are working with the system designer in the design and operation of the system. The design methodology is presented along with the results of the design and the solutions regarding human factors design principles.

Costs and benefits of future heavy Space Freighters

NASA Astrophysics Data System (ADS)

Arend, H.

1987-10-01

A class of two-stage reusable ballistic Space Freighters with nominal launch masses of 7000 metric tons for transport of heavy payloads into low earth orbits is investigated in this paper with spcial regard to vehicle cost efficiency. A life-cycle cost analysis shows that Space Freighters with a conventional aluminum structure offer significantly lower specific transportation costs than today's systems for large payload markets and high launch rates. Advanced structural materials and thermal protection systems offer further important reductions not only with regard to vehicle mass but also with respect to specific transportation cost. A phased introduction of these technologies is cost efficient for larger programs with more than 100 vehicles.

Analysis of alternatives for immobilized low activity waste disposal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burbank, D.A.

This report presents a study of alternative disposal system architectures and implementation strategies to provide onsite near-surface disposal capacity to receive the immobilized low-activity waste produced by the private vendors. The analysis shows that a flexible unit strategy that provides a suite of design solutions tailored to the characteristics of the immobilized low-activity waste will provide a disposal system that best meets the program goals of reducing the environmental, health, and safety impacts; meeting the schedule milestones; and minimizing the life-cycle cost of the program.

Determining system boundaries on commercial broiler chicken production system using ISO 14040/14044 guideline: A case Study

NASA Astrophysics Data System (ADS)

Sidek, ‘A. A.; Suffian, S. A.; Al-Hazza, M. H. F.; Yusof, H. M.

2018-01-01

The demand of poultry product in Malaysia market shows an escalation throughout the year and expected to increase in the future. The expansion of poultry production has led to environmental concern in relation to their operational impact to environmentAt present, assessment of waste management of poultry production in Malaysia is lacking. A case study research was conducted in a commercial broiler farm to identify and assess the system boundaries in the lifecycle supply chain of broiler chicken production using ISO 14040/44 guidelines. ISO 14040/44 standard includes Life Cycle Assessment (LCA) framework guidelines to evaluate environmental influence associated with a product/process throughout its life span. All attributes associated with broiler operation is defined and the system boundaries is determined to identify possible inputs and outputs in the case study. This paper discuss the initial stage in the LCA process, which set the context of the research and prepare for the stage of Life Cycle Inventory.

Genetic investigation of tricarboxylic acid metabolism during the Plasmodium falciparum life cycle.

PubMed

Ke, Hangjun; Lewis, Ian A; Morrisey, Joanne M; McLean, Kyle J; Ganesan, Suresh M; Painter, Heather J; Mather, Michael W; Jacobs-Lorena, Marcelo; Llinás, Manuel; Vaidya, Akhil B

2015-04-07

New antimalarial drugs are urgently needed to control drug-resistant forms of the malaria parasite Plasmodium falciparum. Mitochondrial electron transport is the target of both existing and new antimalarials. Herein, we describe 11 genetic knockout (KO) lines that delete six of the eight mitochondrial tricarboxylic acid (TCA) cycle enzymes. Although all TCA KOs grew normally in asexual blood stages, these metabolic deficiencies halted life-cycle progression in later stages. Specifically, aconitase KO parasites arrested as late gametocytes, whereas α-ketoglutarate-dehydrogenase-deficient parasites failed to develop oocysts in the mosquitoes. Mass spectrometry analysis of (13)C-isotope-labeled TCA mutant parasites showed that P. falciparum has significant flexibility in TCA metabolism. This flexibility manifested itself through changes in pathway fluxes and through altered exchange of substrates between cytosolic and mitochondrial pools. Our findings suggest that mitochondrial metabolic plasticity is essential for parasite development. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Reducing impacts from ammunitions: A comparative life-cycle assessment of four types of 9mm ammunitions.

PubMed

Ferreira, Carlos; Ribeiro, José; Almada, Sara; Rotariu, Traian; Freire, Fausto

2016-10-01

Increase of environmental awareness of the population has pressured research activities in the defence area to cover environment and toxicity issues, where have been considered appropriate manners to reduce the environmental and toxicological impacts of ammunition. One of the adopted approaches to achieve such goal involves the replacement of lead and other heavy metals by alternative materials. However, the consequences of using alternative materials in ammunitions manufacturing are uncertain for the other life-cycle phases and trade-offs can occur. The present paper describes the potential benefits from the replacement of lead in the primer and in the projectile of a 9mm calibre ammunition. For that purpose, it is assessed and compared the environmental and toxicological impacts associated with the life-cycle of four ammunitions: combination of two types of projectiles (steel jacket and lead core; copper and nylon composite) with two types of primers (lead primer; non-lead primer). In addition, some potential improvements for the environmental performance of small calibre ammunition are also presented. To assess the impacts two Life-Cycle Impact Assessment methods are applied: CML for six environmental categories and USEtox to three toxicity categories. Results showed that the conclusion drawn for environmental and toxicological impact categories are distinct. In fact, ammunition production phase presents higher impacts for the environmental categories, whilst the operation phase has a higher impact to the toxicity categories. The substitution of lead in the primer and in the projectile provides a suitable alternative from a toxicology perspective; however, the composite projectile still presents some environmental concerns. The conclusions drawn are important for the procurement (and design) of environmental responsible ammunitions, in order to avoid (or decrease) the impacts for their manufacture and the effects on human health (e.g. shooters) and ecosystems near shooting ranges or hunting areas. Copyright © 2016 Elsevier B.V. All rights reserved.

Design and analysis of aluminum/air battery system for electric vehicles

NASA Astrophysics Data System (ADS)

Yang, Shaohua; Knickle, Harold

Aluminum (Al)/air batteries have the potential to be used to produce power to operate cars and other vehicles. These batteries might be important on a long-term interim basis as the world passes through the transition from gasoline cars to hydrogen fuel cell cars. The Al/air battery system can generate enough energy and power for driving ranges and acceleration similar to gasoline powered cars. From our design analysis, it can be seen that the cost of aluminum as an anode can be as low as US 1.1/kg as long as the reaction product is recycled. The total fuel efficiency during the cycle process in Al/air electric vehicles (EVs) can be 15% (present stage) or 20% (projected) comparable to that of internal combustion engine vehicles (ICEs) (13%). The design battery energy density is 1300 Wh/kg (present) or 2000 Wh/kg (projected). The cost of battery system chosen to evaluate is US 30/kW (present) or US$ 29/kW (projected). Al/air EVs life-cycle analysis was conducted and compared to lead/acid and nickel metal hydride (NiMH) EVs. Only the Al/air EVs can be projected to have a travel range comparable to ICEs. From this analysis, Al/air EVs are the most promising candidates compared to ICEs in terms of travel range, purchase price, fuel cost, and life-cycle cost.

Design of intelligent composites with life-cycle health management capabilities

NASA Astrophysics Data System (ADS)

Rosania, Colleen L.; Larrosa, Cecilia C.; Chang, Fu-Kuo

2015-03-01

Use of carbon fiber reinforced polymers (CFRPs) presents challenges because of their complex manufacturing processes and different damage mechanics in relation to legacy metal materials. New monitoring methods for manufacturing, quality verification, damage estimation, and prognosis are needed to use CFRPs safely and efficiently. This work evaluates the development of intelligent composite materials using integrated piezoelectric sensors to monitor the material during cure and throughout service life. These sensors are used to propagate ultrasonic waves through the structure for health monitoring. During manufacturing, data is collected at different stages during the cure cycle, detecting the changing material properties during cure and verifying quality and degree of cure. The same sensors can then be used with previously developed techniques to perform damage detection, such as impact detection and matrix crack density estimation. Real-time damage estimation can be combined with prognostic models to predict future propagation of damage in the material. In this work experimental results will be presented from composite coupons with embedded piezoelectric sensors. Cure monitoring and damage detection results derived from analysis of the ultrasonic sensor signal will be shown. Sensitive signal parameters to the different stimuli in both the time and frequency domains will be explored for this analysis. From these results, use of the same sensor networks from manufacturing throughout the life of the composite material will demonstrate the full life-cycle monitoring capability of these intelligent materials.

Antiviral Effects of ABMA against Herpes Simplex Virus Type 2 In Vitro and In Vivo

PubMed Central

Dai, Wenwen; Wu, Yu; Bi, Jinpeng; Wang, Shuai; Li, Fang; Kong, Wei; Cintrat, Jean-Christophe; Gao, Feng; Su, Weiheng; Jiang, Chunlai

2018-01-01

Herpes simplex virus type 2 (HSV-2) is the causative pathogen of genital herpes and is closely associated with the occurrence of cervical cancer and human immunodeficiency virus (HIV) infection. The absence of an effective vaccine and the emergence of drug resistance to commonly used nucleoside analogs emphasize the urgent need for alternative antivirals against HSV-2. Recently, ABMA [1-adamantyl (5-bromo-2-methoxybenzyl) amine] has been demonstrated to be an inhibitor of several pathogens exploiting host-vesicle transport, which also participates in the HSV-2 lifecycle. Here, we showed that ABMA inhibited HSV-2-induced cytopathic effects and plaque formation with 50% effective concentrations of 1.66 and 1.08 μM, respectively. We also preliminarily demonstrated in a time of compound addition assay that ABMA exerted a dual antiviral mechanism by impairing virus entry, as well as the late stages of the HSV-2 lifecycle. Furthermore, in vivo studies showed that ABMA protected BALB/c mice from intravaginal HSV-2 challenge with an improved survival rate of 50% at 5 mg/kg (8.33% for the untreated virus infected control). Consequently, our study has identified ABMA as an effective inhibitor of HSV-2, both in vitro and in vivo, for the first time and presents an alternative to nucleoside analogs for HSV-2 infection treatment. PMID:29522484

Syk inhibitors interfere with erythrocyte membrane modification during P falciparum growth and suppress parasite egress.

PubMed

Pantaleo, Antonella; Kesely, Kristina R; Pau, Maria Carmina; Tsamesidis, Ioannis; Schwarzer, Evelin; Skorokhod, Oleksii A; Chien, Huynh D; Ponzi, Marta; Bertuccini, Lucia; Low, Philip S; Turrini, Francesco M

2017-08-24

Band 3 (also known as the anion exchanger, SLCA1, AE1) constitutes the major attachment site of the spectrin-based cytoskeleton to the erythrocyte's lipid bilayer and thereby contributes critically to the stability of the red cell membrane. During the intraerythrocytic stage of Plasmodium falciparum 's lifecycle, band 3 becomes tyrosine phosphorylated in response to oxidative stress, leading to a decrease in its affinity for the spectrin/actin cytoskeleton and causing global membrane destabilization. Because this membrane weakening is hypothesized to facilitate parasite egress and the consequent dissemination of released merozoites throughout the bloodstream, we decided to explore which tyrosine kinase inhibitors might block the kinase-induced membrane destabilization. We demonstrate here that multiple Syk kinase inhibitors both prevent parasite-induced band 3 tyrosine phosphorylation and inhibit parasite-promoted membrane destabilization. We also show that the same Syk kinase inhibitors suppress merozoite egress near the end of the parasite's intraerythrocytic lifecycle. Because the entrapped merozoites die when prevented from escaping their host erythrocytes and because some Syk inhibitors have displayed long-term safety in human clinical trials, we suggest Syk kinase inhibitors constitute a promising class of antimalarial drugs that can suppress parasitemia by inhibiting a host target that cannot be mutated by the parasite to evolve drug resistance. © 2017 by The American Society of Hematology.

Greenhouse gas emissions of alternative pavement designs: framework development and illustrative application.

PubMed

Liu, Xiaoyu; Cui, Qingbin; Schwartz, Charles

2014-01-01

Pavement rehabilitation is carbon intensive and the choice of pavement type is a critical factor in controlling greenhouse gas (GHG) emissions. The existing body of knowledge is not able to support decision-making on pavement choice due to a lack of consensus on the system boundaries, the functional units and the estimation periods. Excessive data requirements further inhibit the generalization of the existing methodologies for design evaluation at the early planning stage. This study proposes a practical life-cycle GHG estimation approach, which is arguably effective to benchmark pavement emissions given project bid tabulation. A set of case studies conducted for this study suggest that recycled asphalt pavement (e.g., foam stabilized base (FSB), and warm mix asphalt (WMA)) would prevent up to 50% of GHGs from the initial construction phase. However, from a life-cycle perspective, pavement emissions are dictated largely by the traffic characteristics and the analysis period for the use phase. The benefits from using recycled materials (e.g., FSB) are likely to diminish if the recycled products do not perform as well as those properly proportioned with less recycled materials, or if the recycled materials are locally unavailable. When the AADT reaches 10,000, use phase releases more than 97% of the life cycle emissions and the emissions difference among alternative designs will be within 1%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Applying GIS and high performance agent-based simulation for managing an Old World Screwworm fly invasion of Australia.

PubMed

Welch, M C; Kwan, P W; Sajeev, A S M

2014-10-01

Agent-based modelling has proven to be a promising approach for developing rich simulations for complex phenomena that provide decision support functions across a broad range of areas including biological, social and agricultural sciences. This paper demonstrates how high performance computing technologies, namely General-Purpose Computing on Graphics Processing Units (GPGPU), and commercial Geographic Information Systems (GIS) can be applied to develop a national scale, agent-based simulation of an incursion of Old World Screwworm fly (OWS fly) into the Australian mainland. The development of this simulation model leverages the combination of massively data-parallel processing capabilities supported by NVidia's Compute Unified Device Architecture (CUDA) and the advanced spatial visualisation capabilities of GIS. These technologies have enabled the implementation of an individual-based, stochastic lifecycle and dispersal algorithm for the OWS fly invasion. The simulation model draws upon a wide range of biological data as input to stochastically determine the reproduction and survival of the OWS fly through the different stages of its lifecycle and dispersal of gravid females. Through this model, a highly efficient computational platform has been developed for studying the effectiveness of control and mitigation strategies and their associated economic impact on livestock industries can be materialised. Copyright © 2014 International Atomic Energy Agency 2014. Published by Elsevier B.V. All rights reserved.

Product Lifecycle Management and Sustainable Space Exploration

NASA Technical Reports Server (NTRS)

Caruso, Pamela W.; Dumbacher, Daniel L.; Grieves, Michael

2011-01-01

This slide presentation reviews the use of product lifecycle management (PLM) in the general aerospace industry, its use and development at NASA and at Marshall Space Flight Center, and how the use of PLM can lead to sustainable space exploration.

Temperature fine-tunes Mediterranean Arabidopsis thaliana life-cycle phenology geographically.

PubMed

Marcer, A; Vidigal, D S; James, P M A; Fortin, M-J; Méndez-Vigo, B; Hilhorst, H W M; Bentsink, L; Alonso-Blanco, C; Picó, F X

2018-01-01

To understand how adaptive evolution in life-cycle phenology operates in plants, we need to unravel the effects of geographic variation in putative agents of natural selection on life-cycle phenology by considering all key developmental transitions and their co-variation patterns. We address this goal by quantifying the temperature-driven and geographically varying relationship between seed dormancy and flowering time in the annual Arabidopsis thaliana across the Iberian Peninsula. We used data on genetic variation in two major life-cycle traits, seed dormancy (DSDS50) and flowering time (FT), in a collection of 300 A. thaliana accessions from the Iberian Peninsula. The geographically varying relationship between life-cycle traits and minimum temperature, a major driver of variation in DSDS50 and FT, was explored with geographically weighted regressions (GWR). The environmentally varying correlation between DSDS50 and FT was analysed by means of sliding window analysis across a minimum temperature gradient. Maximum local adjustments between minimum temperature and life-cycle traits were obtained in the southwest Iberian Peninsula, an area with the highest minimum temperatures. In contrast, in off-southwest locations, the effects of minimum temperature on DSDS50 were rather constant across the region, whereas those of minimum temperature on FT were more variable, with peaks of strong local adjustments of GWR models in central and northwest Spain. Sliding window analysis identified a minimum temperature turning point in the relationship between DSDS50 and FT around a minimum temperature of 7.2 °C. Above this minimum temperature turning point, the variation in the FT/DSDS50 ratio became rapidly constrained and the negative correlation between FT and DSDS50 did not increase any further with increasing minimum temperatures. The southwest Iberian Peninsula emerges as an area where variation in life-cycle phenology appears to be restricted by the duration and severity of the hot summer drought. The temperature-driven varying relationship between DSDS50 and FT detected environmental boundaries for the co-evolution between FT and DSDS50 in A. thaliana. In the context of global warming, we conclude that A. thaliana phenology from the southwest Iberian Peninsula, determined by early flowering and deep seed dormancy, might become the most common life-cycle phenotype for this annual plant in the region. © 2017 German Botanical Society and The Royal Botanical Society of the Netherlands.

Current Strategies for Inhibition of Chikungunya Infection.

PubMed

Subudhi, Bharat Bhusan; Chattopadhyay, Soma; Mishra, Priyadarsee; Kumar, Abhishek

2018-05-03

Increasing incidences of Chikungunya virus (CHIKV) infection and co-infections with Dengue/Zika virus have highlighted the urgency for CHIKV management. Failure in developing effective vaccines or specific antivirals has fuelled further research. This review discusses updated strategies of CHIKV inhibition and provides possible future directions. In addition, it analyzes advances in CHIKV lifecycle, drug-target development, and potential hits obtained by in silico and experimental methods. Molecules identified with anti-CHIKV properties using traditional/rational drug design and their potential to succeed in subsequent stages of drug development have also been discussed. Possibilities of repurposing existing drugs based on their in vitro findings have also been elucidated. Probable modes of interference of these compounds at various stages of infection, including entry and replication, have been highlighted. The use of host factors as targets to identify antivirals against CHIKV has been addressed. While most of the earlier antivirals were effective in the early phases of the CHIKV life cycle, this review is also focused on drug candidates that are effective at multiple stages of its life cycle. Since most of these antivirals require validation in preclinical and clinical models, the challenges regarding this have been discussed and will provide critical information for further research.

Current Strategies for Inhibition of Chikungunya Infection

PubMed Central

Subudhi, Bharat Bhusan; Chattopadhyay, Soma; Mishra, Priyadarsee

2018-01-01

Increasing incidences of Chikungunya virus (CHIKV) infection and co-infections with Dengue/Zika virus have highlighted the urgency for CHIKV management. Failure in developing effective vaccines or specific antivirals has fuelled further research. This review discusses updated strategies of CHIKV inhibition and provides possible future directions. In addition, it analyzes advances in CHIKV lifecycle, drug-target development, and potential hits obtained by in silico and experimental methods. Molecules identified with anti-CHIKV properties using traditional/rational drug design and their potential to succeed in subsequent stages of drug development have also been discussed. Possibilities of repurposing existing drugs based on their in vitro findings have also been elucidated. Probable modes of interference of these compounds at various stages of infection, including entry and replication, have been highlighted. The use of host factors as targets to identify antivirals against CHIKV has been addressed. While most of the earlier antivirals were effective in the early phases of the CHIKV life cycle, this review is also focused on drug candidates that are effective at multiple stages of its life cycle. Since most of these antivirals require validation in preclinical and clinical models, the challenges regarding this have been discussed and will provide critical information for further research. PMID:29751486

An Index of Longitudinal Hydrologic Connectivity to Evaluate Effects of Water Abstraction on Streams Dominated by Migratory Shrimps

NASA Astrophysics Data System (ADS)

Crook, K. E.; Pringle, C. M.; Freeman, M. C.; Scatena, F. N.

2005-05-01

Massive water withdrawals from streams draining the Caribbean National Forest (CNF), Puerto Rico, are threatening their biotic integrity. Migratory tropical shrimps are ideal indicator species to measure water withdrawal effects on riverine connectivity and biointegrity because: (1) their migratory range encompasses the stream network from estuaries to headwater streams; (2) they represent greater than 90% of biomass in streams draining the CNF; and (3) they facilitate important in-stream ecological processes. We developed an index to evaluate individual and cumulative effects of water intakes on each stage of the shrimp's life-cycle. Effect of water withdrawal on longitudinal connectivity was evaluated by combining effects of water withdrawal on larval and juvenile shrimps. Larvae require downstream transport to the estuary for advancement to the next life-stage, and juveniles similarly require access to headwater streams. Therefore, these two life-stages represent the bi-directional connectivity of streams from headwaters to estuaries. Seventeen water intakes were evaluated in and around the CNF. Larger intakes cause a greater decrease in connectivity than smaller intakes; however, several small, high elevation intakes had very low connectivity. Also, intakes with alternative designs, such as a French drain, have reduced effects on connectivity.

A Sensitivity Analysis of the Rigid Pavement Life-Cycle Cost Analysis Program

DOT National Transportation Integrated Search

2000-12-01

Original Report Date: September 1999. This report describes the sensitivity analysis performed on the Rigid Pavement Life-Cycle Cost Analysis program, a computer program developed by the Center for Transportation Research for the Texas Department of ...

Life-cycle economics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lunde, P.J.

1982-09-01

In a continuation of previous economic analyses, life-cycle economics of solar projects are discussed using the concept of net present value (NPV) or net worth. The discount rate is defined and illustrated and a life-cycle analysis is worked out based on no down payment and a 25-year loan. The advantages of rising NPV are discussed and illustrated using an energy conserving $100 storm window as an example. Real payback period is discussed and it is concluded that NPV is the only valid method for the evaluation of an investment. Return on investment is cited as a satisfactory alternative method. (MJJ)

Infrastructure and automobile shifts: positioning transit to reduce life-cycle environmental impacts for urban sustainability goals

NASA Astrophysics Data System (ADS)

Chester, Mikhail; Pincetl, Stephanie; Elizabeth, Zoe; Eisenstein, William; Matute, Juan

2013-03-01

Public transportation systems are often part of strategies to reduce urban environmental impacts from passenger transportation, yet comprehensive energy and environmental life-cycle measures, including upfront infrastructure effects and indirect and supply chain processes, are rarely considered. Using the new bus rapid transit and light rail lines in Los Angeles, near-term and long-term life-cycle impact assessments are developed, including consideration of reduced automobile travel. Energy consumption and emissions of greenhouse gases and criteria pollutants are assessed, as well the potential for smog and respiratory impacts. Results show that life-cycle infrastructure, vehicle, and energy production components significantly increase the footprint of each mode (by 48-100% for energy and greenhouse gases, and up to 6200% for environmental impacts), and emerging technologies and renewable electricity standards will significantly reduce impacts. Life-cycle results are identified as either local (in Los Angeles) or remote, and show how the decision to build and operate a transit system in a city produces environmental impacts far outside of geopolitical boundaries. Ensuring shifts of between 20-30% of transit riders from automobiles will result in passenger transportation greenhouse gas reductions for the city, and the larger the shift, the quicker the payback, which should be considered for time-specific environmental goals.

Life-Cycle Costing of Food Waste Management in Denmark: Importance of Indirect Effects.

PubMed

Martinez-Sanchez, Veronica; Tonini, Davide; Møller, Flemming; Astrup, Thomas Fruergaard

2016-04-19

Prevention has been suggested as the preferred food waste management solution compared to alternatives such as conversion to animal fodder or to energy. In this study we used societal life-cycle costing, as a welfare economic assessment, and environmental life-cycle costing, as a financial assessment combined with life-cycle assessment, to evaluate food waste management. Both life-cycle costing assessments included direct and indirect effects. The latter are related to income effects, accounting for the marginal consumption induced when alternative scenarios lead to different household expenses, and the land-use-changes effect, associated with food production. The results highlighted that prevention, while providing the highest welfare gains as more services/goods could be consumed with the same income, could also incur the highest environmental impacts if the monetary savings from unpurchased food commodities were spent on goods/services with a more environmentally damaging production than that of the (prevented) food. This was not the case when savings were used, e.g., for health care, education, and insurances. This study demonstrates that income effects, although uncertain, should be included whenever alternative scenarios incur different financial costs. Furthermore, it highlights that food prevention measures should not only demote the purchase of unconsumed food but also promote a low-impact use of the savings generated.

The economic value of innovative treatments over the product life cycle: the case of targeted trastuzumab therapy for breast cancer.

PubMed

Garrison, Louis P; Veenstra, David L

2009-01-01

Pharmacoeconomic analyses typically project the expected cost-effectiveness of a new product for a specific indication. This analysis develops a dynamic life-cycle model to conduct a multi-indication evaluation using the case of trastuzumab licensed in the United States for both early-stage and metastatic (or late-stage) human epidermal growth factor receptor 2 (HER2)-positive breast cancer therapy (early breast cancer [EBC]; metastatic breast cancer [MBC]), approved in 2006 and 1998, respectively. This dynamic model combined information on expected incremental cost-utility ratios for specific indications with an epidemiologically based projection of utilization by indication over the product life cycle-from 1998 to 2016. Net economic value was estimated as the cumulative quality-adjusted life years (QALYs) gained over the life cycle multiplied by a societal valuation of health gains ($/QALY) minus cumulative net direct treatment costs. Sensitivity analyses were performed under a range of assumptions. We projected that the annual number of EBC patients receiving trastuzumab will be more than three times that of MBC by 2016, in part because adjuvant treatment reduces the future incidence of MBC. Over this life cycle, the estimated overall incremental cost-effectiveness ratio (ICER) was $35,590/QALY with a total of 432,547 discounted QALYs gained. Under sensitivity analyses, the overall ICER varied from $21,000 to $53,000/QALY, and the projected net economic value resulting from trastuzumab treatment ranged from $6.2 billion to $49.5 billion. Average ICERs for multi-indication compounds can increase or decrease over the product life cycle. In this example, the projected overall life-cycle ICER for trastuzumab was less than one half of that in the initial indication. This dynamic perspective-versus the usual static one-highlights the interdependence of drug development decisions and investment incentives, raising important reimbursement policy issues.

A life-cycle model for wave-dominated tidal inlets along passive margin coasts of North America

NASA Astrophysics Data System (ADS)

Seminack, Christopher T.; McBride, Randolph A.

2018-03-01

A regional overview of 107 wave-dominated tidal inlets along the U.S. Atlantic coast, U.S. Gulf of Mexico coast, and Canadian Gulf of St. Lawrence coast yielded a generalized wave-dominated tidal inlet life-cycle model that recognized the rotational nature of tidal inlets. Tidal inlets are influenced by concurrently acting processes transpiring over two timescales: short-term, event-driven processes and long-term, evolutionary processes. Wave-dominated tidal inlets are classified into three rotational categories based on net longshore sediment transport direction and rotation direction along the landward (back-barrier) portion of the inlet channel: downdrift channel rotation, updrift channel rotation, or little-to-no channel rotation. Lateral shifting of the flood-tidal delta depocenter in response to available estuarine accommodation space appears to control inlet channel rotation. Flood-tidal delta deposits fill accommodation space locally within the estuary (i.e., creating bathymetric highs), causing the tidal-inlet channel to rotate. External influences, such as fluvial discharge, pre-existing back-barrier channels, and impeding salt marsh will also influence inlet-channel rotation. Storm events may rejuvenate the tidal inlet by scouring sediment within the flood-tidal delta, increasing local accommodation space. Wave-dominated tidal inlets are generally unstable and tend to open, concurrently migrate laterally and rotate, infill, and close. Channel rotation is a primary reason for wave-dominated tidal inlet closure. During rotation, the inlet channel lengthens and hydraulic efficiency decreases, thus causing tidal prism to decrease. Tidal prism, estuarine accommodation space, and sediment supply to the flood-tidal delta are the primary variables responsible for tidal inlet rotation. Stability of wave-dominated tidal inlets is further explained by: stability (S) = tidal prism (Ω) + estuarine accommodation space (V) - volume of annual sediment supply (Mt). Rotating wave-dominated tidal inlets follow a six-stage evolutionary model; whereas wave-dominated tidal inlets that exhibit little-to-no rotation follow a five-stage evolutionary model.

Bipartite life cycle of coral reef fishes promotes increasing shape disparity of the head skeleton during ontogeny: an example from damselfishes (Pomacentridae)

PubMed Central

2011-01-01

Background Quantitative studies of the variation of disparity during ontogeny exhibited by the radiation of coral reef fishes are lacking. Such studies dealing with the variation of disparity, i.e. the diversity of organic form, over ontogeny could be a first step in detecting evolutionary mechanisms in these fishes. The damselfishes (Pomacentridae) have a bipartite life-cycle, as do the majority of demersal coral reef fishes. During their pelagic dispersion phase, all larvae feed on planktonic prey. On the other hand, juveniles and adults associated with the coral reef environment show a higher diversity of diets. Using geometric morphometrics, we study the ontogenetic dynamic of shape disparity of different head skeletal units (neurocranium, suspensorium and opercle, mandible and premaxilla) in this fish family. We expected that larvae of different species might be relatively similar in shapes. Alternatively, specialization may become notable even in the juvenile and adult phase. Results The disparity levels increase significantly throughout ontogeny for each skeletal unit. At settlement, all larval shapes are already species-specific. Damselfishes show high levels of ontogenetic allometry during their post-settlement growth. The divergence of allometric patterns largely explains the changes in patterns and levels of shape disparity over ontogeny. The rate of shape change and the length of ontogenetic trajectories seem to be less variable among species. We also show that the high levels of shape disparity at the adult stage are correlated to a higher level of ecological and functional diversity in this stage. Conclusion Diversification throughout ontogeny of damselfishes results from the interaction among several developmental novelties enhancing disparity. The bipartite life-cycle of damselfishes exemplifies a case where the variation of environmental factors, i.e. the transition from the more homogeneous oceanic environment to the coral reef offering a wide range of feeding habits, promotes increasing shape disparity of the head skeleton over the ontogeny of fishes. PMID:21450094

Software And Systems Engineering Risk Management

DTIC Science & Technology

2010-04-01

RSKM 2004 COSO Enterprise RSKM Framework 2006 ISO/IEC 16085 Risk Management Process 2008 ISO/IEC 12207 Software Lifecycle Processes 2009 ISO/IEC...1 Software And Systems Engineering Risk Management John Walz VP Technical and Conferences Activities, IEEE Computer Society Vice-Chair Planning...Software & Systems Engineering Standards Committee, IEEE Computer Society US TAG to ISO TMB Risk Management Working Group Systems and Software

Title TBA: Revising the Abstract Submission Process.

PubMed

Tibon, Roni; Open Science Committee, Cbu; Henson, Richard

2018-04-01

Academic conferences are among the most prolific scientific activities, yet the current abstract submission and review process has serious limitations. We propose a revised process that would address these limitations, achieve some of the aims of Open Science, and stimulate discussion throughout the entire lifecycle of the scientific work. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Functional and Behavioral Product Information Representation and Consistency Validation for Collaboration in Product Lifecycle Activities

ERIC Educational Resources Information Center

Baysal, Mehmet Murat

2012-01-01

Information models that represent the function, assembly and behavior of artifacts are critical in the conceptual development of a product and its evaluation. Much research has been conducted in this area; however, existing models do not relate function, behavior and structure in a comprehensive and consistent way. In this work, NIST's Core…

"Where did my data layer come from?" The semantics of data release

NASA Astrophysics Data System (ADS)

Leadbetter, Adam; Buck, Justin

2015-04-01

In his lecture, "Theory of Creative Fitting" (Margullis, Corner & Holt, 2006), Ian McHarg introduced his vision for cross-disciplinary data and information sharing networks with the end goal of producing detailed overlay maps for the purposes of ecological architectural planning. Within McHarg's networks, experts in various fields, such as hydrology or surface geology, would provide data layers to the final overlay map with full provenance, such that the users of the overlay maps would know the originator of the data, the "value systems" by which the data were created and could place their trust in the outcomes. In the light of McHarg's statements and in order to allow the encoding of value systems in a cyber-GIS, analyses of: data quality (Giarlo, 2013); data publication networks (Reinsfelder, 2012); trust in collaborative research networks (Leadbetter, 2015); and the metaphors of data publication, data release and data ecosystems (Parsons & Fox, 2013) have been synthesised into a logical model of the data release lifecycle. This model concerns the actors in the data release process; the data-information-knowledge ecosystem through the various stages of the data release process and the impact of data release on perceptions of trust through the data release lifecycle. The data-information-knowledge ecosystem described how the collection of data can be presented in new ways to form information products, and how these information products can inform conversations amongst information-consumers who integrate the information into new knowledge. The actors concerned in the process comprise: researchers data publishers academic publishers & academic administrators Finally, the lifecycle of data release involves the initial release of a data-layer, possibly with a Persistent Identifier (PID) more generic than a Digital Object Identifier (DOI). A data description paper can be written about the dataset, which then necessitates the assignment of a DOI to the datasets; the DOI can be seen as an indicator of trust through "benevolence". A technical document citing the dataset may then be informed by the dataset release or the dataset description paper. These citations may show the "competence" (in terms of a trust model) of the original datasets, and the dataset description papers or other technical articles show the integrity of the dataset. The synthesised logical model has been represented in freely available ontologies, such that data layers can be annotated with metadata about their provenance and stage within the data release lifecycle before incorporation into a cyber-GIS, in which distributed data providers provide for a collaborative research environment. References Giarlo, M. (2013). Academic libraries as data quality hubs. Journal of Librarianship and Scholarly Communication 1(3): eP1059. doi: 10.7710/2162-3309.1059 Leadbetter, A. (2015). Examining trust in collaborative research networks. In P. Diviacco, P. Fox, C. Pshenichny, and A. Leadbetter (Eds.) Collaborative Knowledge in Scientific Research Networks, Hershey, PA: IGI Global. doi: 10.4018/978-1-4666-6567-5.ch002 Margulis, L., Corner, J. and Hawthorne, B. (Editors), 2006. Ian McHarg: conversations with students. Dwelling with nature. New York, NY: Princeton Architectural Press. Parsons, M., and Fox, P. (2013). Is data publication the right metaphor? Data Science Journal 12, 32-46. doi:10.2481/dsj.WDS-042 Reinsfelder, T. (2012). Open access publishing practices in a complex environment: conditions, barriers and bases of power. Journal of Librarianship and Scholarly Communication 1(1): eP1029. doi: 10.7710/2162-3309.1029

The SnSAG merozoite surface antigens of Sarcocystis neurona are expressed differentially during the bradyzoite and sporozoite life cycle stages.

PubMed

Gautam, A; Dubey, J P; Saville, W J; Howe, D K

2011-12-29

Sarcocystis neurona is a two-host coccidian parasite whose complex life cycle progresses through multiple developmental stages differing at morphological and molecular levels. The S. neurona merozoite surface is covered by multiple, related glycosylphosphatidylinositol-linked proteins, which are orthologous to the surface antigen (SAG)/SAG1-related sequence (SRS) gene family of Toxoplasma gondii. Expression of the SAG/SRS proteins in T. gondii and another related parasite Neospora caninum is life-cycle stage specific and seems necessary for parasite transmission and persistence of infection. In the present study, the expression of S. neurona merozoite surface antigens (SnSAGs) was evaluated in the sporozoite and bradyzoite stages. Western blot analysis was used to compare SnSAG expression in merozoites versus sporozoites, while immunocytochemistry was performed to examine expression of the SnSAGs in merozoites versus bradyzoites. These analyses revealed that SnSAG2, SnSAG3 and SnSAG4 are expressed in sporozoites, while SnSAG5 was appeared to be downregulated in this life cycle stage. In S. neurona bradyzoites, it was found that SnSAG2, SnSAG3, SnSAG4 and SnSAG5 were either absent or expression was greatly reduced. As shown for T. gondii, stage-specific expression of the SnSAGs may be important for the parasite to progress through its developmental stages and complete its life cycle successfully. Thus, it is possible that the SAG switching mechanism by these parasites could be exploited as a point of intervention. As well, the alterations in surface antigen expression during different life cycle stages may need to be considered when designing prospective approaches for protective vaccination. Copyright © 2011 Elsevier B.V. All rights reserved.

Geohazard assessment lifecycle for a natural gas pipeline project

NASA Astrophysics Data System (ADS)

Lekkakis, D.; Boone, M. D.; Strassburger, E.; Li, Z.; Duffy, W. P.

2015-09-01

This paper is a walkthrough of the geohazard risk assessment performed for the Front End Engineering Design (FEED) of a planned large-diameter natural gas pipeline, extending from Eastern Europe to Western Asia for a total length of approximately 1,850 km. The geohazards discussed herein include liquefaction-induced pipe buoyancy, cyclic softening, lateral spreading, slope instability, groundwater rise-induced pipe buoyancy, and karst. The geohazard risk assessment lifecycle was comprised of 4 stages: initially a desktop study was carried out to describe the geologic setting along the alignment and to conduct a preliminary assessment of the geohazards. The development of a comprehensive Digital Terrain Model topography and aerial photography data were fundamental in this process. Subsequently, field geohazard mapping was conducted with the deployment of 8 teams of geoprofessionals, to investigate the proposed major reroutes and delve into areas of poor or questionable data. During the third stage, a geotechnical subsurface site investigation was then executed based on the results of the above study and mapping efforts in order to obtain sufficient data tailored for risk quantification. Lastly, all gathered and processed information was overlain into a Geographical Information database towards a final determination of the critical reaches of the pipeline alignment. Input from Subject Matter Experts (SME) in the fields of landslides, karst and fluvial geomorphology was incorporated during the second and fourth stages of the assessment. Their experience in that particular geographical region was key to making appropriate decisions based on engineering judgment. As the design evolved through the above stages, the pipeline corridor was narrowed from a 2-km wide corridor, to a 500-m corridor and finally to a fixed alignment. Where the geohazard risk was high, rerouting of the pipeline was generally selected as a mitigation measure. In some cases of high uncertainty in the assessment, further exploration was proposed. In cases where rerouting was constrained, mitigation via structural measures was proposed. This paper further discusses the cost, schedule and resource challenges of planning and executing such a large-scale geotechnical investigation, the interfaces between the various disciplines involved during the assessment, the innovative tools employed for the field mapping, the classifications developed for mapping landslides, karst geology, and trench excavatability, determining liquefaction stretches and the process for the site localization of the Above Ground Installations (AGI). It finally discusses the objectives of the FEED study in terms of providing a route, a ± 20% project cost estimate and a schedule, and the additional engineering work foreseen to take place in the detailed engineering phase of the project.

Flap flexibility amongst plasmepsins I, II, III, IV, and V: Sequence, structural, and molecular dynamics analyses.

PubMed

McGillewie, Lara; Soliman, Mahmoud E

2015-09-01

Herein, for the first time, we comparatively report the opening and closing of apo plasmepsin I - V. Plasmepsins belong the aspartic protease family of enzymes, and are expressed during the various stages of the P. falciparum lifecycle, the species responsible for the most lethal and virulent malaria to infect humans. Plasmepsin I, II, IV and HAP degrade hemoglobin from infected red blood cells, whereas plasmepsin V transport proteins crucial to the survival of the malaria parasite across the endoplasmic reticulum. Flap-structures covering the active site of aspartic proteases (such as HIV protease) are crucial to the conformational flexibility and dynamics of the protein, and ultimately control the binding landscape. The flap-structure in plasmepsins is made up of a flip tip in the N-terminal lying perpendicular to the active site, adjacent to the flexible loop region in the C-terminal. Using molecular dynamics, we propose three parameters to better describe the opening and closing of the flap-structure in apo plasmepsins. Namely, the distance, d1, between the flap tip and the flexible region; the dihedral angle, ϕ, to account for the twisting motion; and the TriCα angle, θ1. Simulations have shown that as the flap-structure twists, the flap and flexible region move apart opening the active site, or move toward each other closing the active site. The data from our study indicate that of all the plasmepsins investigated in the present study, Plm IV and V display the highest conformational flexibility and are more dynamic structures versus Plm I, II, and HAP. © 2015 Wiley Periodicals, Inc.

The antimalarial drug primaquine targets Fe-S cluster proteins and yeast respiratory growth.

PubMed

Lalève, Anaïs; Vallières, Cindy; Golinelli-Cohen, Marie-Pierre; Bouton, Cécile; Song, Zehua; Pawlik, Grzegorz; Tindall, Sarah M; Avery, Simon V; Clain, Jérôme; Meunier, Brigitte

2016-04-01

Malaria is a major health burden in tropical and subtropical countries. The antimalarial drug primaquine is extremely useful for killing the transmissible gametocyte forms of Plasmodium falciparum and the hepatic quiescent forms of P. vivax. Yet its mechanism of action is still poorly understood. In this study, we used the yeast Saccharomyces cerevisiae model to help uncover the mode of action of primaquine. We found that the growth inhibitory effect of primaquine was restricted to cells that relied on respiratory function to proliferate and that deletion of SOD2 encoding the mitochondrial superoxide dismutase severely increased its effect, which can be countered by the overexpression of AIM32 and MCR1 encoding mitochondrial enzymes involved in the response to oxidative stress. This indicated that ROS produced by respiratory activity had a key role in primaquine-induced growth defect. We observed that Δsod2 cells treated with primaquine displayed a severely decreased activity of aconitase that contains a Fe-S cluster notoriously sensitive to oxidative damage. We also showed that in vitro exposure to primaquine impaired the activity of purified aconitase and accelerated the turnover of the Fe-S cluster of the essential protein Rli1. It is suggested that ROS-labile Fe-S groups are the primary targets of primaquine. Aconitase activity is known to be essential at certain life-cycle stages of the malaria parasite. Thus primaquine-induced damage of its labile Fe-S cluster - and of other ROS-sensitive enzymes - could inhibit parasite development. Copyright © 2015. Published by Elsevier B.V.

Cloning of peroxisome proliferators activated receptors in the cobia (Rachycentron canadum) and their expression at different life-cycle stages under cage aquaculture.

PubMed

Tsai, Mei-Ling; Chen, Houng-Yung; Tseng, Mei-Cheuh; Chang, Rey-Chang

2008-12-01

We present the cDNA sequences and tissue mRNA expression of peroxisome proliferator-activated receptor (PPAR) alpha, beta and gamma isotypes in the cobia (Rachycentron canadum), a warm water pelagic fish that is becoming a fish of choice for offshore cage farming. RT-PCR and real-time PCR showed that PPARalpha mRNA predominated in red muscle, heart and liver whereas PPARbeta was expressed mainly in liver and pyloric caeca. In contrast, PPARgamma transcripts were detected in all of the tissues examined, with the highest level occurring in visceral fat depot. Our 52-wk time-series investigation showed that while the mRNA expression of PPARgamma in the cobia was positively (P < 0.05) related to its body lipid deposition, a negative (P < 0.05) relationship was found between PPARalpha expression in the liver and body lipid deposition. There was a significant increase in body lipid deposition and hepatic PPARgamma expression as the fish grew. The hepatic PPARgamma expression could be a sufficient parameter describing the bodily expression of PPARgamma because of its positive correlation with PPARgamma expressions in all other tissues. These results showed that PPARgamma and alpha played a pivotal role in the control of lipid metabolic and storage functions in the liver, muscle and visceral fat depot of the cobia.

Disrupting effects of antibiotic sulfathiazole on developmental process during sensitive life-cycle stage of Chironomus riparius.

PubMed

Park, Kiyun; Kwak, Ihn-Sil

2018-01-01

Antibiotics in the environment are a concern due to their potential to harm humans and interrupt ecosystems. Sulfathiazole (STZ), a sulfonamide antibiotic, is commonly used in aquaculture and is typically found in aquatic ecosystems. We evaluated the ecological risk of STZ by examining biological, molecular and biochemical response in Chironomus riparius. Samples were exposed to STZ for 12, 24 and 96 h, and effects of STZ were evaluated at the molecular level by analyzing changes in gene expression related to the endocrine system, cellular stress response and enzyme activity of genes on antioxidant and detoxification pathways. STZ exposure induced significant effects on survival, growth and sex ratio of emergent adults and mouthpart deformity in C. riparius. STZ caused concentration and time-dependent toxicity in most of the selected biomarkers. STZ exposure leads to significant heat-shock response of protein genes (HSP70, HSP40, HSP90 and HSP27) and to disruption by up-regulating selected genes, including the ecdysone receptor gene, estrogen-related receptors, ultraspiracle and E74 early ecdysone-responsive gene. Furthermore, STZ induced alteration of enzyme activities on antioxidant and detoxification responses (catalase, superoxide dismutase, glutathione peroxidase and peroxidase) in C. riparius. By inducing oxidative stress, antibiotic STZ disturbs the endocrine system and produces adverse effects in growth processes of invertebrates. Copyright © 2017 Elsevier Ltd. All rights reserved.

14 CFR 170.23 - LORAN-C establishment criteria.

Code of Federal Regulations, 2012 CFR

2012-01-01

... ratio of the present value of the LORAN-C life-cycle benefits (PVB) to the present value of LORAN-C life-cycle costs (PVC): PVB/PVC ≥ 1.0 (c) The criteria do not cover all situations that may arise and are not...

14 CFR 170.23 - LORAN-C establishment criteria.

Code of Federal Regulations, 2013 CFR

2013-01-01

... ratio of the present value of the LORAN-C life-cycle benefits (PVB) to the present value of LORAN-C life-cycle costs (PVC): PVB/PVC ≥ 1.0 (c) The criteria do not cover all situations that may arise and are not...

Ferry Lifecycle Cost Model for Federal Land Management Agencies : User's Guide.

DOT National Transportation Integrated Search

2011-09-30

The Ferry Lifecycle Cost Model (model) is a spreadsheet-based sketch planning tool that estimates capital, operating, and total cost for various vessels that could be used to provide ferry service on a particular route given known service parameters....

Case study for implementing RECIPPE as a quality control in construction projects.

DOT National Transportation Integrated Search

2008-04-01

The quality of construction is a very important factor in the life-cycle performance of flexible pavements. This is particularly true of the individual characteristics of construction and their relative effect on life-cycle performance of the pavemen...

Eric Tan | NREL

Science.gov Websites

-economic analysis Sustainability and life-cycle analysis (SimaPro, Greenhouse Gases, Regulated Emissions Laboratory Technical Report (2015) "Techno-economic Analysis of Corn and Corn Stover n-Butanol -economic Analysis and Life-cycle Assessment of Cellulosic iso-Butanol and Comparison with Cellulosic

Using Model-Based System Engineering to Provide Artifacts for NASA Project Life-Cycle and Technical Reviews Presentation

NASA Technical Reports Server (NTRS)

Parrott, Edith L.; Weiland, Karen J.

2017-01-01

This is the presentation for the AIAA Space conference in September 2017. It highlights key information from Using Model-Based Systems Engineering to Provide Artifacts for NASA Project Life-cycle and Technical Reviews paper.

Comparative Lifecycle Energy Analysis: Theory and Practice.

ERIC Educational Resources Information Center

Morris, Jeffrey; Canzoneri, Diana

1992-01-01

Explores the position that more energy is conserved through recycling secondary materials than is generated from municipal solid waste incineration. Discusses one component of a lifecycle analysis--a comparison of energy requirements for manufacturing competing products. Includes methodological issues, energy cost estimates, and difficulties…

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2010 CFR

2010-10-01

... delivered to DoD that will enhance logistics, contracting, and financial business transactions supporting... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide...

Incorporating exposure science into life-cycle assessment

EPA Science Inventory

Life-cycle assessment (LCA) is used to estimate the potential for environmental damage that may be caused by a product or process, ideally before the product or process begins. LCA includes all of the steps from extracting natural resources through manufacturing through product u...

Energy-Efficient Routes for the Production of Gasoline from Biogas and Pyrolysis Oil-Process Design and Life-Cycle Assessment.

PubMed

Sundaram, Smitha; Kolb, Gunther; Hessel, Volker; Wang, Qi

2017-03-29

Two novel routes for the production of gasoline from pyrolysis oil (from timber pine) and biogas (from ley grass) are simulated, followed by a cradle-to-gate life-cycle assessment of the two production routes. The main aim of this work is to conduct a holistic evaluation of the proposed routes and benchmark them against the conventional route of producing gasoline from natural gas. A previously commercialized method of synthesizing gasoline involves conversion of natural gas to syngas, which is further converted to methanol, and then as a last step, the methanol is converted to gasoline. In the new proposed routes, the syngas production step is different; syngas is produced from a mixture of pyrolysis oil and biogas in the following two ways: (i) autothermal reforming of pyrolysis oil and biogas, in which there are two reactions in one reactor (ATR) and (ii) steam reforming of pyrolysis oil and catalytic partial oxidation of biogas, in which there are separated but thermally coupled reactions and reactors (CR). The other two steps to produce methanol from syngas, and gasoline from methanol, remain the same. The purpose of this simulation is to have an ex-ante comparison of the performance of the new routes against a reference, in terms of energy and sustainability. Thus, at this stage of simulations, nonrigorous, equilibrium-based models have been used for reactors, which will give the best case conversions for each step. For the conventional production route, conversion and yield data available in the literature have been used, wherever available.The results of the process design showed that the second method (separate, but thermally coupled reforming) has a carbon efficiency of 0.53, compared to the conventional route (0.48), as well as the first route (0.40). The life-cycle assessment results revealed that the newly proposed processes have a clear advantage over the conventional process in some categories, particularly the global warming potential and primary energy demand; but there are also some in which the conventional route fares better, such as the human toxicity potential and the categories related to land-use change such as biotic production potential and the groundwater resistance indicator. The results confirmed that even though using biomass such as timber pine as raw material does result in reduced greenhouse gas emissions, the activities associated with biomass, such as cultivation and harvesting, contribute to the environmental footprint, particularly the land use change categories. This gives an impetus to investigate the potential of agricultural, forest, or even food waste, which would be likely to have a substantially lower impact on the environment. Moreover, it could be seen that the source of electricity used in the process has a major impact on the environmental performance.

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

48 CFR 211.274-1 - General.

Code of Federal Regulations, 2013 CFR

2013-10-01

... on leading practices and embraces open standards, DoD can— (a) Achieve lower life-cycle cost of item management and improve life-cycle property management; (b) Improve operational readiness; (c) Provide reliable accountability of property and asset visibility throughout the life cycle; and (d) Reduce the...

Overview of Design, Lifecycle, and Safety for Computer-Based Systems

NASA Technical Reports Server (NTRS)

Torres-Pomales, Wilfredo

2015-01-01

This document describes the need and justification for the development of a design guide for safety-relevant computer-based systems. This document also makes a contribution toward the design guide by presenting an overview of computer-based systems design, lifecycle, and safety.

Enabling Smart Manufacturing Research and Development using a Product Lifecycle Test Bed.

PubMed

Helu, Moneer; Hedberg, Thomas

2015-01-01

Smart manufacturing technologies require a cyber-physical infrastructure to collect and analyze data and information across the manufacturing enterprise. This paper describes a concept for a product lifecycle test bed built on a cyber-physical infrastructure that enables smart manufacturing research and development. The test bed consists of a Computer-Aided Technologies (CAx) Lab and a Manufacturing Lab that interface through the product model creating a "digital thread" of information across the product lifecycle. The proposed structure and architecture of the test bed is presented, which highlights the challenges and requirements of implementing a cyber-physical infrastructure for manufacturing. The novel integration of systems across the product lifecycle also helps identify the technologies and standards needed to enable interoperability between design, fabrication, and inspection. Potential research opportunities enabled by the test bed are also discussed, such as providing publicly accessible CAx and manufacturing reference data, virtual factory data, and a representative industrial environment for creating, prototyping, and validating smart manufacturing technologies.

Comparing Life-Cycle Costs of ESPCs and Appropriations-Funded Energy Projects: An Update to the 2002 Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shonder, John A; Hughes, Patrick; Atkin, Erica

2006-11-01

A study was sponsored by FEMP in 2001 - 2002 to develop methods to compare life-cycle costs of federal energy conservation projects carried out through energy savings performance contracts (ESPCs) and projects that are directly funded by appropriations. The study described in this report follows up on the original work, taking advantage of new pricing data on equipment and on $500 million worth of Super ESPC projects awarded since the end of FY 2001. The methods developed to compare life-cycle costs of ESPCs and directly funded energy projects are based on the following tasks: (1) Verify the parity of equipmentmore » prices in ESPC vs. directly funded projects; (2) Develop a representative energy conservation project; (3) Determine representative cycle times for both ESPCs and appropriations-funded projects; (4) Model the representative energy project implemented through an ESPC and through appropriations funding; and (5) Calculate the life-cycle costs for each project.« less

Enabling Smart Manufacturing Research and Development using a Product Lifecycle Test Bed

PubMed Central

Helu, Moneer; Hedberg, Thomas

2017-01-01

Smart manufacturing technologies require a cyber-physical infrastructure to collect and analyze data and information across the manufacturing enterprise. This paper describes a concept for a product lifecycle test bed built on a cyber-physical infrastructure that enables smart manufacturing research and development. The test bed consists of a Computer-Aided Technologies (CAx) Lab and a Manufacturing Lab that interface through the product model creating a “digital thread” of information across the product lifecycle. The proposed structure and architecture of the test bed is presented, which highlights the challenges and requirements of implementing a cyber-physical infrastructure for manufacturing. The novel integration of systems across the product lifecycle also helps identify the technologies and standards needed to enable interoperability between design, fabrication, and inspection. Potential research opportunities enabled by the test bed are also discussed, such as providing publicly accessible CAx and manufacturing reference data, virtual factory data, and a representative industrial environment for creating, prototyping, and validating smart manufacturing technologies. PMID:28664167

A comparison between the multimedia fate and exposure models CalTOX and uniform system for evaluation of substances adapted for life-cycle assessment based on the population intake fraction of toxic pollutants.

PubMed

Huijbregts, Mark A J; Geelen, Loes M J; Hertwich, Edgar G; McKone, Thomas E; van de Meent, Dik

2005-02-01

In life-cycle assessment (LCA) and comparative risk assessment, potential human exposure to toxic pollutants can be expressed as the population intake fraction (iF), which represents the fraction of the quantity emitted that enters the human population. To assess the influence of model differences in the calculation of the population iF ingestion and inhalation iFs of 365 substances emitted to air, freshwater, and soil were calculated with two commonly applied multimedia fate and exposure models, CalTOX and the uniform system for evaluation of substances adapted for life-cycle assessment (USES-LCA). The model comparison showed that differences in the iFs due to model choices were the lowest after emission to air and the highest after emission to soil. Inhalation iFs were more sensitive to model differences compared to ingestion iFs. The choice for a continental seawater compartment, vertical stratification of the soil compartment, rain and no-rain scenarios, and drinking water purification mainly clarify the relevant model differences found in population iFs. Furthermore, pH correction of chemical properties and aerosol-associated deposition on plants appeared to be important for dissociative organics and metals emitted to air, respectively. Finally, it was found that quantitative structure-activity relationship estimates for superhydrophobics may introduce considerable uncertainty in the calculation of population intake fractions.

Second NASA Technical Interchange Meeting (TIM): Advanced Technology Lifecycle Analysis System (ATLAS) Technology Tool Box (TTB)

NASA Technical Reports Server (NTRS)

ONeil, D. A.; Mankins, J. C.; Christensen, C. B.; Gresham, E. C.

2005-01-01

The Advanced Technology Lifecycle Analysis System (ATLAS), a spreadsheet analysis tool suite, applies parametric equations for sizing and lifecycle cost estimation. Performance, operation, and programmatic data used by the equations come from a Technology Tool Box (TTB) database. In this second TTB Technical Interchange Meeting (TIM), technologists, system model developers, and architecture analysts discussed methods for modeling technology decisions in spreadsheet models, identified specific technology parameters, and defined detailed development requirements. This Conference Publication captures the consensus of the discussions and provides narrative explanations of the tool suite, the database, and applications of ATLAS within NASA s changing environment.

Comparative Proteomic Analysis of Hymenolepis diminuta Cysticercoid and Adult Stages

PubMed Central

Sulima, Anna; Savijoki, Kirsi; Bień, Justyna; Näreaho, Anu; Sałamatin, Rusłan; Conn, David Bruce; Młocicki, Daniel

2018-01-01

Cestodiases are common parasitic diseases of animals and humans. As cestodes have complex lifecycles, hexacanth larvae, metacestodes (including cysticercoids), and adults produce proteins allowing them to establish invasion and to survive in the hostile environment of the host. Hymenolepis diminuta is the most commonly used model cestode in experimental parasitology. The aims of the present study were to perform a comparative proteomic analysis of two consecutive developmental stages of H. diminuta (cysticercoid and adult) and to distinguish proteins which might be characteristic for each of the stages from those shared by both stages. Somatic proteins of H. diminuta were isolated from 6-week-old cysticercoids and adult tapeworms. Cysticercoids were obtained from experimentally infected beetles, Tenebrio molitor, whereas adult worms were collected from experimentally infected rats. Proteins were separated by GeLC-MS/MS (one dimensional gel electrophoresis coupled with liquid chromatography and tandem mass spectrometry). Additionally protein samples were digested in-liquid and identified by LC-MS/MS. The identified proteins were classified according to molecular function, cellular components and biological processes. Our study showed a number of differences and similarities in the protein profiles of cysticercoids and adults; 233 cysticercoid and 182 adult proteins were identified. From these proteins, 131 were present only in the cysticercoid and 80 only in the adult stage samples. Both developmental stages shared 102 proteins; among which six represented immunomodulators and one is a potential drug target. In-liquid digestion and LC-MS/MS complemented and confirmed some of the GeLC-MS/MS identifications. Possible roles and functions of proteins identified with both proteomic approaches are discussed. PMID:29379475

Making Use of a Decade of Widely Varying Historical Data: SARP Project - "Full Life-Cycle Defect Management"

NASA Technical Reports Server (NTRS)

Shull, Forrest; Godfrey, Sally; Bechtel, Andre; Feldmann, Raimund L.; Regardie, Myrna; Seaman, Carolyn

2008-01-01

A viewgraph presentation describing the NASA Software Assurance Research Program (SARP) project, with a focus on full life-cycle defect management, is provided. The topics include: defect classification, data set and algorithm mapping, inspection guidelines, and tool support.

LED street lighting evaluation -- phase II : LED specification and life-cycle cost analysis.

DOT National Transportation Integrated Search

2015-01-01

Phase II of this study focused on developing a draft specification for LED luminaires to be used by IDOT : and a life-cycle cost analysis (LCCA) tool for solid state lighting technologies. The team also researched the : latest developments related to...

Streamline Your Project: A Lifecycle Model.

ERIC Educational Resources Information Center

Viren, John

2000-01-01

Discusses one approach to project organization providing a baseline lifecycle model for multimedia/CBT development. This variation of the standard four-phase model of Analysis, Design, Development, and Implementation includes a Pre-Analysis phase, called Definition, and a Post-Implementation phase, known as Maintenance. Each phase is described.…

The Process of Life Cycle Cost Analysis: Projecting Economic Consequences of Design Decisions

ERIC Educational Resources Information Center

AIA Journal, 1976

1976-01-01

Life-cycle cost analysis deals with both present and future costs and attempts to relate the two as a basis for making decisions. This article lays the groundwork for a better understanding of the techniques of life-cycle cost analysis. (Author/MLF)

Determination of the appropriate use of pavement surface history in the KDOT life-cycle analysis process.

DOT National Transportation Integrated Search

2008-09-01

The primary objective of this study was to evaluate KDOTs pavement surfacing history and recommend : whether or not the departments life-cycle cost analysis (LCCA) procedure should include a surfacing history : component, and, if so, how the LC...

Interrogating alkyl and arylalkylpolyamino (bis)urea and (bis)thiourea isosteres as potent antimalarial chemotypes against multiple lifecycle forms of Plasmodium falciparum parasites.

PubMed

Verlinden, Bianca K; de Beer, Marna; Pachaiyappan, Boobalan; Besaans, Ethan; Andayi, Warren A; Reader, Janette; Niemand, Jandeli; van Biljon, Riette; Guy, Kiplin; Egan, Timothy; Woster, Patrick M; Birkholtz, Lyn-Marie

2015-08-15

A new series of potent potent aryl/alkylated (bis)urea- and (bis)thiourea polyamine analogues were synthesized and evaluated in vitro for their antiplasmodial activity. Altering the carbon backbone and terminal substituents increased the potency of analogues in the compound library 3-fold, with the most active compounds, 15 and 16, showing half-maximal inhibitory concentrations (IC50 values) of 28 and 30 nM, respectively, against various Plasmodium falciparum parasite strains without any cross-resistance. In vitro evaluation of the cytotoxicity of these analogues revealed marked selectivity towards targeting malaria parasites compared to mammalian HepG2 cells (>5000-fold lower IC50 against the parasite). Preliminary biological evaluation of the polyamine analogue antiplasmodial phenotype revealed that (bis)urea compounds target parasite asexual proliferation, whereas (bis)thiourea compounds of the same series have the unique ability to block transmissible gametocyte forms of the parasite, indicating pluripharmacology against proliferative and non-proliferative forms of the parasite. In this manuscript, we describe these results and postulate a refined structure-activity relationship (SAR) model for antiplasmodial polyamine analogues. The terminally aryl/alkylated (bis)urea- and (bis)thiourea-polyamine analogues featuring a 3-5-3 or 3-6-3 carbon backbone represent a structurally novel and distinct class of potential antiplasmodials with activities in the low nanomolar range, and high selectivity against various lifecycle forms of P. falciparum parasites. Copyright © 2015 Elsevier Ltd. All rights reserved.

Life-cycle effects of single-walled carbon nanotubes (SWNTs) on an estuarine meiobenthic copepod.

PubMed

Templeton, Ryan C; Ferguson, P Lee; Washburn, Kate M; Scrivens, Wally A; Chandler, G Thomas

2006-12-01

Single-walled carbon nanotubes (SWNT) are finding increasing use in consumer electronics and structural composites. These nanomaterials and their manufacturing byproducts may eventually reach estuarine systems through wastewater discharge. The acute and chronic toxicity of SWNTs were evaluated using full life-cycle bioassays with the estuarine copepod Amphiascus tenuiremis (ASTM method E-2317-04). A synchronous cohort of naupliar larvae was assayed by culturing individual larvae to adulthood in individual 96-well microplate wells amended with SWNTs in seawater. Copepods were exposed to "as prepared" (AP) SWNTs, electrophoretically purified SWNTs, or a fluorescent fraction of nanocarbon synthetic byproducts. Copepods ingesting purified SWNTs showed no significant effects on mortality, development, and reproduction across exposures (p < 0.05). In contrast, exposure to the more complex AP-SWNT mixture significantly increased life-cycle mortality, reduced fertilization rates, and reduced molting success in the highest exposure (10 mg x L(-1)) (p < 0.05). Exposure to small fluorescent nanocarbon byproducts caused significantly increased life-cycle mortality at 10 mg x L(-1) (p < 0.05). The fluorescent nanocarbon fraction also caused significant reduction in life-cycle molting success for all exposures (p < 0.05). These results suggest size-dependent toxicity of SWNT-based nanomaterials, with the smallest synthetic byproduct fractions causing increased mortality and delayed copepod development over the concentration ranges tested.

System Evaluation and Life-Cycle Cost Analysis of a Commercial-Scale High-Temperature Electrolysis Hydrogen Production Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwin A. Harvego; James E. O'Brien; Michael G. McKellar

2012-11-01

Results of a system evaluation and lifecycle cost analysis are presented for a commercial-scale high-temperature electrolysis (HTE) central hydrogen production plant. The plant design relies on grid electricity to power the electrolysis process and system components, and industrial natural gas to provide process heat. The HYSYS process analysis software was used to evaluate the reference central plant design capable of producing 50,000 kg/day of hydrogen. The HYSYS software performs mass and energy balances across all components to allow optimization of the design using a detailed process flow sheet and realistic operating conditions specified by the analyst. The lifecycle cost analysismore » was performed using the H2A analysis methodology developed by the Department of Energy (DOE) Hydrogen Program. This methodology utilizes Microsoft Excel spreadsheet analysis tools that require detailed plant performance information (obtained from HYSYS), along with financial and cost information to calculate lifecycle costs. The results of the lifecycle analyses indicate that for a 10% internal rate of return, a large central commercial-scale hydrogen production plant can produce 50,000 kg/day of hydrogen at an average cost of $2.68/kg. When the cost of carbon sequestration is taken into account, the average cost of hydrogen production increases by $0.40/kg to $3.08/kg.« less

The cytotoxic effect of Elephantopus scaber Linn extract against breast cancer (T47D) cells

NASA Astrophysics Data System (ADS)

Sulistyani, N.; Nurkhasanah

2017-11-01

Breast cancer is one of the main cause of death. Elephantopus scaber Linn (ES) which has been used as a traditional medicine contains an antitumor compounds. This study aimed to explore the active fraction from ethanolic extract of ES as anticancer and to determine its inhibition effect on the cell proliferation cycle of breast cancer (T47D) cells. The ES leaf was macerated with ethanol and then evaporated to get the concentrated extract. The extract was fractionated using petroleum ether, chloroform, and methanol respectively. The cytotoxic activity of each fraction was carried out with MTT method, and the inhibition of cell cycle test were observed by flowcytometry method. The result showed that ES and the fractions have cytotoxic activity against T47D cell lines with IC50 values of extract, petroleum ether, chloroform, and methanol fractions were 58.36±2.38, 132.17±9.69, 7.08±2.11, and 572.89±69.23 µg/mL. The inhibition effect of ethanol extract on the lifecycle of cells was occured in sub G1 phase. There was no prolonging of G1, S, G2/M and polyploidy phase of T47D cell lines. The chloroform fraction of ES is the most cytotoxic fraction against T47D cells without prolonging the cell lifecycle.

A comparative life-cycle assessment of briquetting logging residues and lumber manufacturing coproducts in western United States

Treesearch

Sevda Alanya-Rosenbaum; Richard D. Bergman; Indroneil Ganguly; Francesca Pierobon

2018-01-01

Timber harvest activities in the western United States have resulted in large volumes of low- to no-value logging (forest) residues. Alternatives to pile-and-burning are needed to best utilize this material and to mitigate the resultant environmental impacts. Briquetting (densifying) forest residues near-woods is one such option and is the focus of this study. This...

Environmental Assessment of the General Plan and Maintenance of Patrick Air Force Base, Florida

DTIC Science & Technology

2012-07-17

water consumption . Per the National Energy Conservation Policy Act, sustainable design principles and life-cycle cost- effective technologies will...attached EA concluded that no significant adverse effects will result. No significant adverse cumulative impacts will result from activities associated...resources will be considered an adverse effect , however, sufficient documentation had been received for Facilities 1322, 1327, 1330, 1425, 1432, 1437 and

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weisz, Daniel A.; Gross, Michael L.; Pakrasi, Himadri B.

Photosystem II (PSII) is a photosynthetic membrane-protein complex that undergoes an intricate, tightly regulated cycle of assembly, damage, and repair. The available crystal structures of cyanobacterial PSII are an essential foundation for understanding PSII function, but nonetheless provide a snapshot only of the active complex. To study aspects of the entire PSII life-cycle, mass spectrometry (MS) has emerged as a powerful tool that can be used in conjunction with biochemical techniques. In this article, we present the MS-based approaches that are used to study PSII composition, dynamics, and structure, and review the information about the PSII life-cycle that has beenmore » gained by these methods. This information includes the composition of PSII subcomplexes, discovery of accessory PSII proteins, identification of post-translational modifications and quantification of their changes under various conditions, determination of the binding site of proteins not observed in PSII crystal structures, conformational changes that underlie PSII functions, and identification of water and oxygen channels within PSII. Lastly, we conclude with an outlook for the opportunity of future MS contributions to PSII research.« less

Design Methods and Practices for Fault Prevention and Management in Spacecraft

NASA Technical Reports Server (NTRS)

Tumer, Irem Y.

2005-01-01

Integrated Systems Health Management (ISHM) is intended to become a critical capability for all space, lunar and planetary exploration vehicles and systems at NASA. Monitoring and managing the health state of diverse components, subsystems, and systems is a difficult task that will become more challenging when implemented for long-term, evolving deployments. A key technical challenge will be to ensure that the ISHM technologies are reliable, effective, and low cost, resulting in turn in safe, reliable, and affordable missions. To ensure safety and reliability, ISHM functionality, decisions and knowledge have to be incorporated into the product lifecycle as early as possible, and ISHM must be considered as an essential element of models developed and used in various stages during system design. During early stage design, many decisions and tasks are still open, including sensor and measurement point selection, modeling and model-checking, diagnosis, signature and data fusion schemes, presenting the best opportunity to catch and prevent potential failures and anomalies in a cost-effective way. Using appropriate formal methods during early design, the design teams can systematically explore risks without committing to design decisions too early. However, the nature of ISHM knowledge and data is detailed, relying on high-fidelity, detailed models, whereas the earlier stages of the product lifecycle utilize low-fidelity, high-level models of systems and their functionality. We currently lack the tools and processes necessary for integrating ISHM into the vehicle system/subsystem design. As a result, most existing ISHM-like technologies are retrofits that were done after the system design was completed. It is very expensive, and sometimes futile, to retrofit a system health management capability into existing systems. Last-minute retrofits result in unreliable systems, ineffective solutions, and excessive costs (e.g., Space Shuttle TPS monitoring which was considered only after 110 flights and the Columbia disaster). High false alarm or false negative rates due to substandard implementations hurt the credibility of the ISHM discipline. This paper presents an overview of the current state of ISHM design,and a review of formal design methods to make recommendations about possible approaches to enable the ISHM capabilities to be designed-in at the system-level, from the very beginning of the vehicle design process.

How can mortality increase population size? A test of two mechanistic hypotheses.

PubMed

McIntire, Kristina M; Juliano, Steven A

2018-05-03

Overcompensation occurs when added mortality increases survival to the next life-cycle stage. Overcompensation can contribute to the Hydra Effect, wherein added mortality increases equilibrium population size. One hypothesis for overcompensation is that added mortality eases density-dependence, increasing survival to adulthood ("temporal separation of mortality and density dependence"). Mortality early in the life cycle is therefore predicted to cause overcompensation, whereas mortality later in the life cycle is not. Another hypothesis for overcompensation is that threat of mortality (e.g., from predation) causes behavioral changes that reduce overexploitation of resources, allowing resource recovery, and increasing production of adults ("prudent resource exploitation"). Behaviorally active predation cues alone are therefore predicted to cause overcompensation. We tested these predictions in two experiments with larvae of two species of Aedes. As predicted, early mortality yielded greater production of adults, and of adult females, and greater estimated rate of population increase than did later mortality. Addition of water-borne predation cues usually reduced browsing on surfaces in late-stage larvae, but contrary to prediction, resulted in neither significantly greater production of adult mosquitoes nor significantly greater estimated rate of increase. Thus we have strong evidence that timing of mortality contributes to overcompensation and the Hydra effect in mosquitoes. Evidence that predation cues alone can result in overcompensation via prudent resource exploitation is lacking. We expect the overcompensation in response to early mortality will be common in organisms with complex life cycles, density dependence among juveniles, and developmental control of populations. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Optogenetic pacing in Drosophila models (Conference Presentation)

NASA Astrophysics Data System (ADS)

Wu, Penghe; Li, Airong; Men, Jing; Tans, Rudolph E.; Zhou, Chao

2017-02-01

The Drosophila melanogaster shares many similarities with vertebrates in heart development. Comparison of heart structural and functional characteristic between male and female Drosophila melanogaster at different developmental stages is helpful to understand heart morphogenesis and function for different genders. And also, it opens up the possibility to uncover the role of sex-related genes in heart development. In this longitudinal study, we cultured and tracked dozens of individually labeled flies throughout their lifecycle. The heart characteristic was measured at different developmental stages during culturing. The gender of each individual fly was determined by adult stage so that the collected data of early stages could be classified to male or female group. We adapted a high-speed optical coherence microscopy (OCM) system with axial and transverse resolution of 2um and 4um, respectively, to perform non-invasive M-mode imaging at a frame rate of 132Hz in Drosophila heart at third instar larva, early pupa and adult stage. Based on those GPU processed M-mode OCM images, we segmented the fly heart region and then quantified the cardiac structural and functional parameters such as heart rate, heart chamber size and so on. Despite large variances of wild type Drosophila in terms of some cardiac characteristic, our results suggest that the heart rate is lower for male flies than for female flies, especially at third instar larva stage. The end diastolic area (EDA) and end systolic area (ESA) of the heart are both slightly larger in female flies than in male flies at larva and adult stage. In summary, we showed gender differences of wild type drosophila in heart functional and structural characteristic.

Development of a Methodology for Successful Multigeneration Life-Cycle Testing of the Estuarine Sheepshead Minnow, Cyprinodon variegatus.

EPA Science Inventory

Sustainability of wildlife populations exposed to endocrine disrupting chemicals in natural water bodies has sparked sufficient concern that the U.S.EPA is developing methods for multiple generation exposures of fishes. Established testing methods and the short life-cycle of the ...

A Comparative Analysis of Life-Cycle Assessment Tools for End-of-Life Materials Management Systems

EPA Science Inventory

We identified and evaluated five life-cycle assessment tools that community decision makers can use to assess the environmental and economic impacts of end-of-life (EOL) materials management options. The tools evaluated in this report are waste reduction mode (WARM), municipal s...

E-Learning Quality Assurance: A Process-Oriented Lifecycle Model

ERIC Educational Resources Information Center

Abdous, M'hammed

2009-01-01

Purpose: The purpose of this paper is to propose a process-oriented lifecycle model for ensuring quality in e-learning development and delivery. As a dynamic and iterative process, quality assurance (QA) is intertwined with the e-learning development process. Design/methodology/approach: After reviewing the existing literature, particularly…

Teaching Green Engineering: The Case of Ethanol Lifecycle Analysis

ERIC Educational Resources Information Center

Vallero, Daniel A.; Braiser, Chris

2008-01-01

Lifecycle assessment (LCA) is a valuable tool in teaching green engineering and has been used to assess biofuels, including ethanol. An undergraduate engineering course at Duke University has integrated LCA with other interactive teaching techniques to enhance awareness and to inform engineering decision making related to societal issues, such as…

The Lifecycle of a South African Non-governmental Organisation: Primary Science Programme, 1983-1999.

ERIC Educational Resources Information Center

Harvey, Stephen; Peacock, Alan

2001-01-01

Traces the lifecycle of the Primary Science Programme (PSP), 1983-99, a representative South African nongovernmental organization. Shows how the social and economic environment shaped PSP development and demise. Highlights tensions between quality versus quantity, subject versus holistic focus, and participatory versus authoritarian management…

Product Lifecycle Management and the Quest for Sustainable Space Exploration Solutions

NASA Technical Reports Server (NTRS)

Caruso, Pamela W.; Dumbacher, Daniel L.

2010-01-01

Product Lifecycle Management (PLM) is an outcome of lean thinking to eliminate waste and increase productivity. PLM is inextricably tied to the systems engineering business philosophy, coupled with a methodology by which personnel, processes and practices, and information technology combine to form an architecture platform for product design, development, manufacturing, operations, and decommissioning. In this model, which is being implemented by the Engineering Directorate at the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center, total lifecycle costs are important variables for critical decisionmaking. With the ultimate goal to deliver quality products that meet or exceed requirements on time and within budget, PLM is a powerful tool to shape everything from engineering trade studies and testing goals, to integrated vehicle operations and retirement scenarios. This paper will demonstrate how the Engineering Directorate is implementing PLM as part of an overall strategy to deliver safe, reliable, and affordable space exploration solutions. It has been 30 years since the United States fielded the Space Shuttle. The next generation space transportation system requires a paradigm shift such that digital tools and knowledge management, which are central elements of PLM, are used consistently to maximum effect. The outcome is a better use of scarce resources, along with more focus on stakeholder and customer requirements, as a new portfolio of enabling tools becomes second nature to the workforce. This paper will use the design and manufacturing processes, which have transitioned to digital-based activities, to show how PLM supports the comprehensive systems engineering and integration function. It also will go through a launch countdown scenario where an anomaly is detected to show how the virtual vehicle created from paperless processes will help solve technical challenges and improve the likelihood of launching on schedule, with less hands-on labor needed for processing and troubleshooting. Sustainable space exploration solutions demand that all lifecycle phases be optimized. Adopting PLM, which has been used by the automotive industry for many years, for aerospace applications provides a foundation for strong, disciplined systems engineering and accountable return on investment by making lifecycle considerations variables in an iterative decision-making process. This paper combines the perspectives of the founding father of PLM, along with the experience of Engineering leaders who are implementing these processes and practices real-time. As the nation moves from an industrial-based society to one where information is a valued commodity, future NASA programs and projects will benefit from the experience being gained today for the exploration missions of tomorrow.

The use of smart technologies in enabling construction components reuse: A viable method or a problem creating solution?

PubMed

Iacovidou, Eleni; Purnell, Phil; Lim, Ming K

2018-06-15

The exploitation of Radio Frequency Identification (RFID) for tracking and archiving the properties of structural construction components could be a potentially innovative disruption for the construction sector. This is because RFID can stimulate the reuse of construction components and reduce their wastage, hence addressing sustainability issues in the construction sector. To test the plausibility of that idea, this study explores the potential pre-conditions for RFID to facilitate construction components reuse, and develops a guidance for promoting their redistribution back to the supply chain. It also looks at how integrating RFID with Building Information Modelling (BIM) can possibly be a valuable extension of its capabilities, providing the opportunity for tracked components to be incorporated into new structures in an informed, sound way. A preliminary assessment of the strengths, weaknesses, opportunities and threats of the RFID technology is presented in order to depict its current and future potential in promoting construction components' sustainable lifecycle management, while emphasis has been laid on capturing their technical, environmental, economic and social value. Findings suggest that the collection of the right amount of information at the design-construction-deconstruction-reuse-disposal stage is crucial for RFID to become a successful innovation in the construction sector. Although a number of limitations related to the technical operability and recycling of RFID tags seem to currently hinder its uptake for structural components' lifecycle management, future technological innovations could provide solutions that would enable it to become a mainstream practice. Taken together these proposals advocate that the use of RFID and its integration with BIM can create the right environment for the development of new business models focused on sustainable resource management. These models may then unlock multiple values that are otherwise dissipated in the system. If the rapid technological development of RFID capability can be allied to policy interventions that control and manage its uptake along the supply chain, the sustainable lifecycle management of construction components could be radically enhanced. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Stand-alone flat-plate photovoltaic power systems: System sizing and life-cycle costing methodology for Federal agencies

NASA Technical Reports Server (NTRS)

Borden, C. S.; Volkmer, K.; Cochrane, E. H.; Lawson, A. C.

1984-01-01

A simple methodology to estimate photovoltaic system size and life-cycle costs in stand-alone applications is presented. It is designed to assist engineers at Government agencies in determining the feasibility of using small stand-alone photovoltaic systems to supply ac or dc power to the load. Photovoltaic system design considerations are presented as well as the equations for sizing the flat-plate array and the battery storage to meet the required load. Cost effectiveness of a candidate photovoltaic system is based on comparison with the life-cycle cost of alternative systems. Examples of alternative systems addressed are batteries, diesel generators, the utility grid, and other renewable energy systems.

The research and realization of digital management platform for ultra-precision optical elements within life-cycle

NASA Astrophysics Data System (ADS)

Wang, Juan; Wang, Jian; Li, Lijuan; Zhou, Kun

2014-08-01

In order to solve the information fusion, process integration, collaborative design and manufacturing for ultra-precision optical elements within life-cycle management, this paper presents a digital management platform which is based on product data and business processes by adopting the modern manufacturing technique, information technique and modern management technique. The architecture and system integration of the digital management platform are discussed in this paper. The digital management platform can realize information sharing and interaction for information-flow, control-flow and value-stream from user's needs to offline in life-cycle, and it can also enhance process control, collaborative research and service ability of ultra-precision optical elements.

Life-Cycle Assessment of a Distributed-Scale Thermochemical Bioenergy Conversion System

Treesearch

Hongmei Gu; Richard Bergman

2016-01-01

Expanding bioenergy production from woody biomass has the potential to decrease net greenhouse gas (GHG) emissions and improve the energy security of the United States. Science-based and internationally accepted life-cycle assessment (LCA) is an effective tool for policy makers to make scientifically informed decisions on expanding renewable energy production from...

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2013 CFR

2013-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2012 CFR

2012-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

10 CFR 455.63 - Cost-effectiveness testing.

Code of Federal Regulations, 2014 CFR

2014-01-01

... measure to be determined by life-cycle cost analysis or if the applicant requests such an analysis. (1) A life-cycle cost analysis, showing a savings-to-investment ratio greater than or equal to one over the useful life of the energy conservation measure or 15 years, whichever is less, shall be conducted in...

Effects of Louisiana crude oil on the sheepshead minnow (Cyprinodon variegatus) during a life-cycle exposure to laboratory oiled sediment

EPA Science Inventory

Determining the long-term effects of crude oil exposure is critical for ascertaining population-level ecological risks of spill events. A 19-week complete life-cycle experiment was conducted with the estuarine sheepshead minnow (Cyprinodon variegatus) exposed to reference (uncont...

Environmental impact of producing hardwood lumber using life-cycle inventory

Treesearch

Richard D. Bergman; S.A. Bowe

2007-01-01

Using sustainable building materials is gaining a significant presence in the United States therefore proving sustainability claims are becoming increasingly more important. Showing wood products as green building materials is vital for the long-term productivity of the wood building industry. This study examined hardwood lumber manufacturing using Life-Cycle Inventory...

Making Use of a Decade of Widely Varying Historical Data: SARP Project "Full Life-cycle Defect Management"

NASA Technical Reports Server (NTRS)

Shull, Forrest; Bechtel, Andre; Feldmann, Raimund L.; Regardie, Myrna; Seaman, Carolyn

2008-01-01

This viewgraph presentation addresses the question of inspection and verification and validation (V&V) effectiveness of developing computer systems. A specific question is the relation between V&V effectiveness in the early lifecycle of development and the later testing of the developed system.

Obtaining Life-Cycle Cost-Effective Facilities in the Department of Defense

DTIC Science & Technology

2013-01-01

8 Step 3: Regional, Service- Level , and OSD Project Ranking...13 2.3. Actors and Barriers to Life-Cycle Cost-Effective Facilities in the Regional, Service- Level , and OSD Project Ranking...Congressional authorization and appropriation OMB evaluation Regional, service- level , and OSD project ranking Economic analysis and DD form 1391 completed

Life-Cycle Analysis and Inquiry-Based Learning in Chemistry Teaching

ERIC Educational Resources Information Center

Juntunen, Marianne; Aksela, Maija

2013-01-01

The purpose of this design research is to improve the quality of environmental literacy and sustainability education in chemistry teaching through combining a socio-scientific issue, life-cycle analysis (LCA), with inquiry-based learning (IBL). This first phase of the cyclic design research involved 20 inservice trained chemistry teachers from…

Life-cycle inventory of manufacturing hardwood lumber in Southeastern US

Treesearch

Richard D. Bergman; Scott A. Bowe

2012-01-01

Environmental impacts associated with the building industry have become of increasing importance. Materials and energy consumed during manufacture of building materials such as lumber affect a building’s environmental performance. This study determined environmental impacts of manufacturing hardwood lumber in the southeastern US using the life-cycle inventory method....

An Exploratory Study Of Lead Recovery In Lead-Acid Battery Lifecycle In US Market: An Evidence-Based Approach

EPA Science Inventory

Background: This research examines lead recovery and recycling in lead-acid batteries (LAB) which account for 88% of US lead consumption. We explore strategies to maximize lead recovery and recycling in the LAB lifecycle. Currently, there is limited information on recycling ra...

A Family Life-Cycle Approach to the Socioeconomic Attainment of Working Women.

ERIC Educational Resources Information Center

Hanson, Sandra L.

1983-01-01

Examined married women's (N=453) social and economic labor market attainments from a family life-cycle perspective using a longitudinal study. Findings suggest that the effects of early family experiences on attainment are larger and more permanent than those of later family experiences and actually increase over time. (Author/JAC)

Life-Cycle Inventory Analysis of Manufacturing Redwood Decking

Treesearch

Richard D. Bergman; Han-Sup Han; Elaine Oneil; Ivan L. Eastin

2012-01-01

Green building has become increasingly important. Therefore, consumers and builders often take into account the environmental attributes of a building material. This study determined the environmental attributes associated with manufacturing 38-mm × 138-mm (nominal 2 × 6) redwood decking in northern California using the life-cycle inventory method. Primary data...

LIFE-CYCLE EVALUATION OF GREENHOUSE GAS EMISSIONS FROM MUNICIPAL SOLID WASTE MANAGEMENT IN THE UNITED STATES

EPA Science Inventory

The paper discusses a life-cycle evaluation of greenhouse gas (GHG) emissions from municipal soild waste (MSW) management in the U.S. (NOTE: Using integrated waste management, recycling/composting, waste-to-energy, and better control of landfill gas, communities across the U.S. a...

Developing Second Graders' Creativity through Literacy-Science Integrated Lessons on Lifecycles

ERIC Educational Resources Information Center

Webb, Angela Naomi; Rule, Audrey C.

2012-01-01

Young children need to develop creative problem-solving skills to ensure success in an uncertain future workplace. Although most teachers recognize the importance of creativity, they do not always know how integrate it with content learning. This repeated measures study on animal and plant lifecycles examined student learning of vocabulary and…

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2012 CFR

2012-01-01

...-investment ratio is the ratio of the present value of net cost savings attributable to an energy conservation measure to the present value of the net increase in investment, maintenance and operating, and replacement... present value. The format for displaying life-cycle costs shall be a savings-to-investment ratio. (b) An...

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-investment ratio is the ratio of the present value of net cost savings attributable to an energy conservation measure to the present value of the net increase in investment, maintenance and operating, and replacement... present value. The format for displaying life-cycle costs shall be a savings-to-investment ratio. (b) An...

10 CFR 455.64 - Life-cycle cost methodology.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-investment ratio is the ratio of the present value of net cost savings attributable to an energy conservation measure to the present value of the net increase in investment, maintenance and operating, and replacement... present value. The format for displaying life-cycle costs shall be a savings-to-investment ratio. (b) An...

A quantitative risk model for early lifecycle decision making

NASA Technical Reports Server (NTRS)

Feather, M. S.; Cornford, S. L.; Dunphy, J.; Hicks, K.

2002-01-01

Decisions made in the earliest phases of system development have the most leverage to influence the success of the entire development effort, and yet must be made when information is incomplete and uncertain. We have developed a scalable cost-benefit model to support this critical phase of early-lifecycle decision-making.

[Update on the epidemiology of hydatidosis. Hydatid echinococci: species; life cycles; epidemiologic consequences].

PubMed

Euzéby, J

1990-05-01

Human hydatidosis results from infestation by two species of Echinococcus. (1) E. vogeli, the life-cycle of which occurs in amazonian forests and involves wild canidae and cuniculidae. (2) E. granulosus, which includes two geographical groups: (a) Northern group, with two sub-species E. g borelis and E. g. canadensis, the life-cycle of which is sylvatic and that are agents of a pulmonary hydatidosis which may affect Man. (b) "European" (actually cosmopolitan) form, with two sub-species: (1) E. q. equinus (equine strain) occurring between dogs and horses and unable to infect Man; (2) E. g. granulosus, with several strains and clones according to the species of their intermediate hosts and which are the agents of synanthropic or sylvatic life-cycles. Man may enter into some of these life cycles, but not into all of them: ovine strains, chiefly, but pig and camel strains also, have a zoonotic incidence. From these data, the author emphasizes the epidemiological features of human hydatidosis, which over-runs the classical rural one, resulting from the drog-sheep life-cycle.

Product Lifecycle Management and the Quest for Sustainable Space Exploration Solutions

NASA Technical Reports Server (NTRS)

Caruso, Pamela W.; Dumbacher, Daniel L.; Grieves, Michael

2011-01-01

Product Lifecycle Management (PLM) is an outcome of lean thinking to eliminate waste and increase productivity. PLM is inextricably tied to the systems engineering business philosophy, coupled with a methodology by which personnel, processes and practices, and information technology combine to form an architecture platform for product design, development, manufacturing, operations, and decommissioning. In this model, which is being implemented by the Marshall Space Flight Center (MSFC) Engineering Directorate, total lifecycle costs are important variables for critical decision-making. With the ultimate goal to deliver quality products that meet or exceed requirements on time and within budget, PLM is a powerful concept to shape everything from engineering trade studies and testing goals, to integrated vehicle operations and retirement scenarios. This briefing will demonstrate how the MSFC Engineering Directorate is implementing PLM as part of an overall strategy to deliver safe, reliable, and affordable space exploration solutions and how that strategy aligns with the Agency and Center systems engineering policies and processes. Sustainable space exploration solutions demand that all lifecycle phases be optimized, and engineering the next generation space transportation system requires a paradigm shift such that digital tools and knowledge management, which are central elements of PLM, are used consistently to maximum effect. Adopting PLM, which has been used by the aerospace and automotive industry for many years, for spacecraft applications provides a foundation for strong, disciplined systems engineering and accountable return on investment. PLM enables better solutions using fewer resources by making lifecycle considerations in an integrative decision-making process.

Downside Risk Optimization of the Thrift Savings Plan Lifecycle Fund Portfolios

DTIC Science & Technology

2010-03-01

ETF funds follow indices like the TSP individual funds but are valued by investors due to their “ stock -like” features and low administrative costs...investors worldwide. According to US News and World Report, actively managed stock funds lost nearly 41% on average in 2008 (Mardquardt, 2009...TSP funds: the Government Securities Investment (G) Fund, Fixed Income Index Investment (F) Fund, Common Stock Index Investment (C) Fund, Small

Community composition, diversity, and metabolism of intestinal microbiota in cultivated European eel (Anguilla anguilla).

PubMed

Huang, Wei; Cheng, Zhiqiang; Lei, Shaonan; Liu, Lanying; Lv, Xin; Chen, Lihua; Wu, Miaohong; Wang, Chao; Tian, Baoyu; Song, Yongkang

2018-05-01

The intestinal tract, which harbours tremendous numbers of bacteria, plays a pivotal role in the digestion and absorption of nutrients. Here, high-throughput sequencing technology was used to determine the community composition and complexity of the intestinal microbiota in cultivated European eels during three stages of their lifecycle, after which the metabolic potentials of their intestinal microbial communities were assessed. The results demonstrated that European eel intestinal microbiota were dominated by bacteria in the phyla Proteobacteria and Fusobacteria. Statistical analyses revealed that the three cultured European eel life stages (elver, yellow eel, and silver eel) shared core microbiota dominated by Aeromonas. Phylogenetic Investigation of Communities by Reconstruction of Unobserved States (PICRUSt) predictions of metagenome function revealed that the European eel intestinal microbiota might play significant roles in host nutrient metabolism. Biolog AN MicroPlate™ analysis and extracellular enzyme assays of culturable intestinal bacteria showed that the intestinal microbiota have a marked advantage in the metabolism of starch, which is the main carbohydrate component in European eel formulated feed. Understanding the ecology and functions of the intestinal microbiota during different developmental stages will help us improve the effects of fish-based bacteria on the composition and metabolic capacity of nutrients in European eels.

Strong Delayed Interactive Effects of Metal Exposure and Warming: Latitude-Dependent Synergisms Persist Across Metamorphosis.

PubMed

Debecker, Sara; Dinh, Khuong V; Stoks, Robby

2017-02-21

As contaminants are often more toxic at higher temperatures, predicting their impact under global warming remains a key challenge for ecological risk assessment. Ignoring delayed effects, synergistic interactions between contaminants and warming, and differences in sensitivity across species' ranges could lead to an important underestimation of the risks. We addressed all three mechanisms by studying effects of larval exposure to zinc and warming before, during, and after metamorphosis in Ischnura elegans damselflies from high- and low-latitude populations. By integrating these mechanisms into a single study, we could identify two novel patterns. First, during exposure zinc did not affect survival, whereas it induced mild to moderate postexposure mortality in the larval stage and at metamorphosis, and very strongly reduced adult lifespan. This severe delayed effect across metamorphosis was especially remarkable in high-latitude animals, as they appeared almost insensitive to zinc during the larval stage. Second, the well-known synergism between metals and warming was manifested not only during the larval stage but also after metamorphosis, yet notably only in low-latitude damselflies. These results highlight that a more complete life-cycle approach that incorporates the possibility of delayed interactions between contaminants and warming in a geographical context is crucial for a more realistic risk assessment in a warming world.

Insulation Cork Boards-Environmental Life Cycle Assessment of an Organic Construction Material.

PubMed

Silvestre, José D; Pargana, Nuno; de Brito, Jorge; Pinheiro, Manuel D; Durão, Vera

2016-05-20

Envelope insulation is a relevant technical solution to cut energy consumption and reduce environmental impacts in buildings. Insulation Cork Boards (ICB) are a natural thermal insulation material whose production promotes the recycling of agricultural waste. The aim of this paper is to determine and evaluate the environmental impacts of the production, use, and end-of-life processing of ICB. A "cradle-to-cradle" environmental Life Cycle Assessment (LCA) was performed according to International LCA standards and the European standards on the environmental evaluation of buildings. These results were based on site-specific data and resulted from a consistent methodology, fully described in the paper for each life cycle stage: Cork oak tree growth, ICB production, and end-of-life processing-modeling of the carbon flows ( i.e. , uptakes and emissions), including sensitivity analysis of this procedure; at the production stage-the modeling of energy processes and a sensitivity analysis of the allocation procedures; during building operation-the expected service life of ICB; an analysis concerning the need to consider the thermal diffusivity of ICB in the comparison of the performance of insulation materials. This paper presents the up-to-date "cradle-to-cradle" environmental performance of ICB for the environmental categories and life-cycle stages defined in European standards.

Bumblebee family lineage survival is enhanced in high-quality landscapes.

PubMed

Carvell, Claire; Bourke, Andrew F G; Dreier, Stephanie; Freeman, Stephen N; Hulmes, Sarah; Jordan, William C; Redhead, John W; Sumner, Seirian; Wang, Jinliang; Heard, Matthew S

2017-03-23

Insect pollinators such as bumblebees (Bombus spp.) are in global decline. A major cause of this decline is habitat loss due to agricultural intensification. A range of global and national initiatives aimed at restoring pollinator habitats and populations have been developed. However, the success of these initiatives depends critically upon understanding how landscape change affects key population-level parameters, such as survival between lifecycle stages, in target species. This knowledge is lacking for bumblebees, because of the difficulty of systematically finding and monitoring colonies in the wild. We used a combination of habitat manipulation, land-use and habitat surveys, molecular genetics and demographic and spatial modelling to analyse between-year survival of family lineages in field populations of three bumblebee species. Here we show that the survival of family lineages from the summer worker to the spring queen stage in the following year increases significantly with the proportion of high-value foraging habitat, including spring floral resources, within 250-1,000 m of the natal colony. This provides evidence for a positive impact of habitat quality on survival and persistence between successive colony cycle stages in bumblebee populations. These findings also support the idea that conservation interventions that increase floral resources at a landscape scale and throughout the season have positive effects on wild pollinators in agricultural landscapes.

Life Cycle Assessment of Wall Systems

NASA Astrophysics Data System (ADS)

Ramachandran, Sriranjani

Natural resource depletion and environmental degradation are the stark realities of the times we live in. As awareness about these issues increases globally, industries and businesses are becoming interested in understanding and minimizing the ecological footprints of their activities. Evaluating the environmental impacts of products and processes has become a key issue, and the first step towards addressing and eventually curbing climate change. Additionally, companies are finding it beneficial and are interested in going beyond compliance using pollution prevention strategies and environmental management systems to improve their environmental performance. Life-cycle Assessment (LCA) is an evaluative method to assess the environmental impacts associated with a products' life-cycle from cradle-to-grave (i.e. from raw material extraction through to material processing, manufacturing, distribution, use, repair and maintenance, and finally, disposal or recycling). This study focuses on evaluating building envelopes on the basis of their life-cycle analysis. In order to facilitate this analysis, a small-scale office building, the University Services Building (USB), with a built-up area of 148,101 ft2 situated on ASU campus in Tempe, Arizona was studied. The building's exterior envelope is the highlight of this study. The current exterior envelope is made of tilt-up concrete construction, a type of construction in which the concrete elements are constructed horizontally and tilted up, after they are cured, using cranes and are braced until other structural elements are secured. This building envelope is compared to five other building envelope systems (i.e. concrete block, insulated concrete form, cast-in-place concrete, steel studs and curtain wall constructions) evaluating them on the basis of least environmental impact. The research methodology involved developing energy models, simulating them and generating changes in energy consumption due to the above mentioned envelope types. Energy consumption data, along with various other details, such as building floor area, areas of walls, columns, beams etc. and their material types were imported into Life-Cycle Assessment software called ATHENA impact estimator for buildings. Using this four-stepped LCA methodology, the results showed that the Steel Stud envelope performed the best and less environmental impact compared to other envelope types. This research methodology can be applied to other building typologies.

Caribbean small-island tourism styles and sustainable strategies

NASA Astrophysics Data System (ADS)

de Albuquerque, Klaus; McElroy, Jerome L.

1992-09-01

This article focuses on developing a sustainable tourism in small Caribbean islands, defined here as those that have populations of fewer than 500,000. Such islands share a very fragile ecology and a high dependence on tourism. They differ in their degree of tourist penetration and visitor density and the related degree of environmental degradation. To explain the link between tourism intensity and ecological vulnerability, the so-called “destination life-cycle model” is presented. This suggests that islands pass through three primary stages of tourist development low-density exploration, rapid growth and consolidation, and high-density maturation involving the substitution of man-made for natural attractions. A broad empirical test of the model is performed through a quantitative examination of the tourism characteristics and visitor densities of a cross section of 23 small Caribbean islands. The three basic stages or tourism styles are identified: low-impact emerging areas, high-density mass-market mature destinations, and rapidly growing intermediate islands in between. Some broad strategies consistent with the systems framework for a sustainable tourism with moderate densitites are briefly explored.

Comparative transcriptome analysis of second- and third-generation merozoites of Eimeria necatrix.

PubMed

Su, Shijie; Hou, Zhaofeng; Liu, Dandan; Jia, Chuanli; Wang, Lele; Xu, Jinjun; Tao, Jianping

2017-08-16

Eimeria is a common genus of apicomplexan parasites that infect diverse vertebrates, most notably poultry, causing serious disease and economic losses. Eimeria species have complex life-cycles consisting of three developmental stages. However, the molecular basis of the Eimeria reproductive mode switch remains an enigma. Total RNA extracted from second- (MZ-2) and third-generation merozoites (MZ-3) of Eimeria necatrix was subjected to transcriptome analysis using RNA sequencing (RNA-seq) followed by qRT-PCR validation. A total of 6977 and 6901 unigenes were obtained from MZ-2 and MZ-3, respectively. Approximately 2053 genes were differentially expressed genes (DEGs) between MZ-2 and MZ-3. Compared with MZ-2, 837 genes were upregulated and 1216 genes were downregulated in MZ-3. Approximately 95 genes in MZ-2 and 48 genes in MZ-3 were further identified to have stage-specific expression. Gene ontology category and KEGG analysis suggested that 216 upregulated genes in MZ-2 were annotated by 70 GO assignments, 242 upregulated genes were associated with 188 signal pathways, while 321 upregulated genes in MZ-3 were annotated by 56 GO assignments, 322 upregulated genes were associated with 168 signal pathways. The molecular functions of upregulated genes in MZ-2 were mainly enriched for protein degradation and amino acid metabolism. The molecular functions of upregulated genes in MZ-3 were mainly enriched for transcriptional activity, cell proliferation and cell differentiation. To the best of our knowledge, this is the first RNA-seq data study of the MZ-2 and MZ-3 stages of E. necatrix; it demonstrates a high number of differentially expressed genes between the MZ-2 and MZ-3 of E. necatrix. This study forms a basis for deciphering the molecular mechanisms underlying the shift from the second to third generation schizogony in Eimeria. It also provides valuable resources for future studies on Eimeria, and provides insight into the understanding of reproductive mode plasticity in different Eimeria species.

The Lifecycle of NASA's Earth Science Enterprise Data Resources

NASA Technical Reports Server (NTRS)

McDonald, Kenneth R.; McKinney, Richard A.; Smith, Timothy B.; Rank, Robert

2004-01-01

A major endeavor of NASA's Earth Science Enterprise (ESE) is to acquire, process, archive and distribute data from Earth observing satellites in support of a broad set of science research and applications in the U. S. and abroad. NASA policy directives specifically call for the agency to collect, announce, disseminate and archive all scientific and technical data resulting from NASA and NASA-funded research. During the active life of the satellite missions, while the data products are being created, validated and refined, a number of NASA organizations have the responsibility for data and information system functions. Following the completion of the missions, the responsibility for the long-term stewardship of the ocean and atmospheric, and land process data products transitions to the National Oceanic and Atmospheric Administration (NOAA) and the U.S. Geological Survey (USGS), respectively. Ensuring that long-term satellite data be preserved to support global climate change studies and other research topics and applications presents some major challenges to NASA and its partners. Over the last several years, with the launch and operation of the EOS satellites and the acquisition and production of an unprecedented volume of Earth science data, the importance of addressing these challenges has been elevated. The lifecycle of NASA's Earth science data has been the subject of several agency and interagency studies and reports and has implications and effects on agency charters, policies and budgets and on their data system's requirements, implementation plans and schedules. While much remains to be done, considerable progress has been made in understanding and addressing the data lifecycle issues.

Management plan documentation standard and Data Item Descriptions (DID). Volume of the information system life-cycle and documentation standards, volume 2

NASA Technical Reports Server (NTRS)

Callender, E. David; Steinbacher, Jody

1989-01-01

This is the second of five volumes of the Information System Life-Cycle and Documentation Standards. This volume provides a well-organized, easily used standard for management plans used in acquiring, assuring, and developing information systems and software, hardware, and operational procedures components, and related processes.

Governance of extended lifecycle in large-scale eHealth initiatives: analyzing variability of enterprise architecture elements.

PubMed

Mykkänen, Juha; Virkanen, Hannu; Tuomainen, Mika

2013-01-01

The governance of large eHealth initiatives requires traceability of many requirements and design decisions. We provide a model which we use to conceptually analyze variability of several enterprise architecture (EA) elements throughout the extended lifecycle of development goals using interrelated projects related to the national ePrescription in Finland.

Environmental impact of manufacturing softwood lumber in northeastern and north central United States

Treesearch

Richard D. Bergman; Scott A. Bowe

2010-01-01

Finding the environmental impact of building materials is becoming increasingly more important because of public environmental awareness. Accurate and precise life-cycle inventory data on wood products are needed to meet this demand. This study examined softwood lumber manufacturing in the northeastern and north central US using life-cycle inventory methods. Material...

14 CFR 170.23 - LORAN-C establishment criteria.

Code of Federal Regulations, 2011 CFR

2011-01-01

... ratio of the present value of the LORAN-C life-cycle benefits (PVB) to the present value of LORAN-C life-cycle costs (PVC): PVB/PVC ≥ 1.0 (c) The criteria do not cover all situations that may arise and are not... acceptable for instrument flight rules operations as a result of an airport airspace analysis conducted in...

Defining and Applying Limits for Test and Flight Through the Project Lifecycle GSFC Standard. [Scope: Non-Cryogenic Systems Tested in Vacuum

NASA Technical Reports Server (NTRS)

Mosier, Carol

2015-01-01

The presentation will be given at the Annual Thermal Fluids Analysis Workshop (TFAWS 2015, NCTS 21070-15) hosted by the Goddard SpaceFlight Center (GSFC) Thermal Engineering Branch (Code 545). The powerpoint presentation details the process of defining limits throughout the lifecycle of a flight project.

Life-Cycle inventory/impact Assessment in the context of Chemical Risk Assessment: An Informatics-driven Scoping Review

EPA Science Inventory

One of the goals of Life-Cycle Assessment (LCA) is to compare the full range of environmental effects assignable to products and services in order to improve processes, support policy and provide a sound “systems-thinking” basis for decision support. How in fact LCA can be incorp...

DDP - a tool for life-cycle risk management

NASA Technical Reports Server (NTRS)

Cornford, S. L.; Feather, M. S.; Hicks, K. A.

2001-01-01

At JPL we have developed, and implemented, a process for achieving life-cycle risk management. This process has been embodied in a software tool and is called Defect Detection and Prevention (DDP). The DDP process can be succinctly stated as: determine where we want to be, what could get in the way and how we will get there.

Making the Mark: The Role of Adenosine Modifications in the Lifecycle of RNA Viruses

PubMed Central

Gonzales-van Horn, Sarah R.; Sarnow, Peter

2017-01-01

Summary Viral epitranscriptomics is a newly emerging field that has identified unique roles for RNA modifications in modulating lifecycles of RNA viruses. Despite the observation of a handful of modified viral RNAs five decades ago, very little was known about how these modifications regulate viral lifecycles, until recently. Here we review the pro- and anti-viral effects of methyl-6-adenosine in distinct viral life cycles, the role of 2′ O-methyl modifications in RNA stability and innate immune sensing, and functions of adenosine to inosine modifications in retroviral life cycles. With roles for over 100 modifications in RNA still unknown, this is a rapidly emerging field that is destined to suggest novel antiviral therapies. PMID:28618265

Benefit-Risk Analysis for Decision-Making: An Approach.

PubMed

Raju, G K; Gurumurthi, K; Domike, R

2016-12-01

The analysis of benefit and risk is an important aspect of decision-making throughout the drug lifecycle. In this work, the use of a benefit-risk analysis approach to support decision-making was explored. The proposed approach builds on the qualitative US Food and Drug Administration (FDA) approach to include a more explicit analysis based on international standards and guidance that enables aggregation and comparison of benefit and risk on a common basis and a lifecycle focus. The approach is demonstrated on six decisions over the lifecycle (e.g., accelerated approval, withdrawal, and traditional approval) using two case studies: natalizumab for multiple sclerosis (MS) and bedaquiline for multidrug-resistant tuberculosis (MDR-TB). © 2016 American Society for Clinical Pharmacology and Therapeutics.

Solutions to health care waste: life-cycle thinking and "green" purchasing.

PubMed

Kaiser, B; Eagan, P D; Shaner, H

2001-03-01

Health care waste treatment is linked to bioaccumulative toxic substances, such as mercury and dioxins, which suggests the need for a new approach to product selection. To address environmental issues proactively, all stages of the product life cycle should be considered during material selection. The purchasing mechanism is a promising channel for action that can be used to promote the use of environmentally preferable products in the health care industry; health care facilities can improve environmental performance and still decrease costs. Tools that focus on environmentally preferable purchasing are now emerging for the health care industry. These tools can help hospitals select products that create the least amount of environmental pollution. Environmental performance should be incorporated into the evolving definition of quality for health care.

The life-cycle of Emiliania huxleyi: A brief review and a study of relative ploidy levels analysed by flow cytometry

NASA Astrophysics Data System (ADS)

Green, J. C.; Course, P. A.; Tarran, G. A.

1996-10-01

Emiliania huxleyi exists in several principal forms including the familiar coccolith-bearing C-cell, non-motile naked N-cells, and scale-bearing swarmers (S-cells), but the relationships between these cells are unclear. Flow cytometric analyses have been undertaken on whole cells using fluorochrome staining of the DNA in order to determine the relative DNA content and the relative GC content of the S- and C-cells of selected clones. Results showed that the DNA complement of the S-cells was half that of the C-cells and the two cell types are, therefore, haploid and diploid relative to each other. The S-cells may, therefore, represent a gametic stage, though processes such as sexual fusion and meiosis have not been observed.

Quantitative Evaluation of Heavy Duty Machine Tools Remanufacturing Based on Modified Catastrophe Progression Method

NASA Astrophysics Data System (ADS)

shunhe, Li; jianhua, Rao; lin, Gui; weimin, Zhang; degang, Liu

2017-11-01

The result of remanufacturing evaluation is the basis for judging whether the heavy duty machine tool can remanufacture in the EOL stage of the machine tool lifecycle management.The objectivity and accuracy of evaluation is the key to the evaluation method.In this paper, the catastrophe progression method is introduced into the quantitative evaluation of heavy duty machine tools’ remanufacturing,and the results are modified by the comprehensive adjustment method,which makes the evaluation results accord with the standard of human conventional thinking.Using the catastrophe progression method to establish the heavy duty machine tools’ quantitative evaluation model,to evaluate the retired TK6916 type CNC floor milling-boring machine’s remanufacturing.The evaluation process is simple,high quantification,the result is objective.

Expanding lean thinking to the product and process design and development within the framework of sustainability

NASA Astrophysics Data System (ADS)

Sorli, M.; Sopelana, A.; Salgado, M.; Pelaez, G.; Ares, E.

2012-04-01

Companies require tools to change towards a new way of developing and producing innovative products to be manufactured considering the economic, social and environmental impact along the product life cycle. Based on translating Lean principles in Product Development (PD) from the design stage and, along the entire product life cycle, it is aimed to address both sustainability and environmental issues. The drivers of sustainable culture within a lean PD have been identified and a baseline for future research on the development of appropriate tools and techniques has been provided. This research provide industry with a framework which balance environmental and sustainable factors with lean principles to be considered and incorporated from the beginning of product design and development covering the entire product lifecycle.

"Birds of passage" or "career" women? Thoughts on the life cycle of the eighteenth-century European servant.

PubMed

Simonton, Deborah

2011-01-01

Frequently eighteenth-century service is described as a life-cycle stage used to build up the financial wherewithal to set up house. As such it was central to the way youth or girlhood was traversed, and studies of adolescent years rightly emphasise the importance of service. However, this narrative, while largely accurate, is also problematic. What happened when service did not end with marriage, or when a woman remained single well into adulthood? In practice, servants were found among both the married and single, and among the young and the old. Concentrating on the eighteenth century, and incorporating material from Nordic Europe, this article teases out some of the nuances in the context and experience of service that partially disrupt the established narrative.

Point clouds in BIM

NASA Astrophysics Data System (ADS)

Antova, Gergana; Kunchev, Ivan; Mickrenska-Cherneva, Christina

2016-10-01

The representation of physical buildings in Building Information Models (BIM) has been a subject of research since four decades in the fields of Construction Informatics and GeoInformatics. The early digital representations of buildings mainly appeared as 3D drawings constructed by CAD software, and the 3D representation of the buildings was only geometric, while semantics and topology were out of modelling focus. On the other hand, less detailed building representations, with often focus on ‘outside’ representations were also found in form of 2D /2,5D GeoInformation models. Point clouds from 3D laser scanning data give a full and exact representation of the building geometry. The article presents different aspects and the benefits of using point clouds in BIM in the different stages of a lifecycle of a building.