Science.gov

Sample records for active thermal management

  1. Weight Optimization of Active Thermal Management Using a Novel Heat Pump

    NASA Technical Reports Server (NTRS)

    Lear, William E.; Sherif, S. A.

    2004-01-01

    Efficient lightweight power generation and thermal management are two important aspects for space applications. Weight is added to the space platforms due to the inherent weight of the onboard power generation equipment and the additional weight of the required thermal management systems. Thermal management of spacecraft relies on rejection of heat via radiation, a process that can result in large radiator mass, depending upon the heat rejection temperature. For some missions, it is advantageous to incorporate an active thermal management system, allowing the heat rejection temperature to be greater than the load temperature. This allows a reduction of radiator mass at the expense of additional system complexity. A particular type of active thermal management system is based on a thermodynamic cycle, developed by the authors, called the Solar Integrated Thermal Management and Power (SITMAP) cycle. This system has been a focus of the authors research program in the recent past (see Fig. 1). One implementation of the system requires no moving parts, which decreases the vibration level and enhances reliability. Compression of the refrigerant working fluid is accomplished in this scheme via an ejector.

  2. Electronic Equipment Thermal Management

    NASA Astrophysics Data System (ADS)

    Berger, R. L.; Jenkins, L. C.

    An assessment is made of the importance of thermal management in electronic equipment design, illustrating the ways in which CAD technology may be used to improve electronic equipment thermal management programs. Attention is given to the Electronic Equipment Thermal Management portion of the aircraft system-level Thermal Management Control (TMC) program. TMC establishes the process by which the airframe's environmental control system and the electronic equipment are integrated to optimize system reliability through life cycle cost minimization, by allocating available cooling capacity to system elements on the basis of derived benefits.

  3. [Perioperative thermal management].

    PubMed

    Bräuer, A; Perl, T; Quintel, M

    2006-12-01

    Perioperative hypothermia can influence clinical outcome negatively. It triples the incidence of adverse myocardial outcomes, significantly increases perioperative blood loss, significantly augments allogenic transfusion requirements, and increases the incidence of surgical wound infections. The major causes are redistribution of heat from the core of the body to the peripheral tissues and a negative heat balance. Adequate thermal management includes preoperative and intraoperative measures. Preoperative measures, e.g., prewarming, enhance heat content of the peripheral tissues, thereby reducing redistribution of heat from the core to the peripheral tissues after induction of anesthesia. Intraoperative measures are active skin surface warming of a large body surface area with conductive or convective warming systems. Intravenous fluids should be warmed when large volumes of more than 500-1000 ml/h are required. The body surfaces that cannot be actively warmed should be insulated. Airway humidification and conductive warming of the back are less efficient. PMID:17136375

  4. Thermal Management and Thermal Protection Systems

    NASA Technical Reports Server (NTRS)

    Hasnain, Aqib

    2016-01-01

    During my internship in the Thermal Design Branch (ES3), I contributed to two main projects: i) novel passive thermal management system for future human exploration, ii) AVCOAT undercut thermal analysis. i) As NASA prepares to further expand human and robotic presence in space, it is well known that spacecraft architectures will be challenged with unprecedented thermal environments. Future exploration activities will have the need of thermal management systems that can provide higher reliability, mass and power reduction and increased performance. In an effort to start addressing the current technical gaps the NASA Johnson Space Center Passive Thermal Discipline has engaged in technology development activities. One of these activities was done through an in-house Passive Thermal Management System (PTMS) design for a lunar lander. The proposed PTMS, functional in both microgravity and gravity environments, consists of three main components: a heat spreader, a novel hybrid wick Variable Conductance Heat Pipe (VCHP), and a radiator. The aim of this PTMS is to keep electronics on a vehicle within their temperature limits (0 and 50 C for the current design) during all mission phases including multiple lunar day/night cycles. The VCHP was tested to verify its thermal performance. I created a thermal math model using Thermal Desktop (TD) and analyzed it to predict the PTMS performance. After testing, the test data provided a means to correlate the thermal math model. This correlation took into account conduction and convection heat transfer, representing the actual benchtop test. Since this PTMS is proposed for space missions, a vacuum test will be taking place to provide confidence that the system is functional in space environments. Therefore, the model was modified to include a vacuum chamber with a liquid nitrogen shroud while taking into account conduction and radiation heat transfer. Infrared Lamps were modelled and introduced into the model to simulate the sun

  5. Metal clad active fibres for power scaling and thermal management at kW power levels.

    PubMed

    Daniel, Jae M O; Simakov, Nikita; Hemming, Alexander; Clarkson, W Andrew; Haub, John

    2016-08-01

    We present a new approach to high power fibre laser design, consisting of a polymer-free all-glass optical fibre waveguide directly overclad with a high thermal conductivity metal coating. This metal clad active fibre allows a significant reduction in thermal resistance between the active fibre and the laser heat-sink as well as a significant increase in the operating temperature range. In this paper we show the results of a detailed thermal analysis of both polymer and metal coated active fibres under thermal loads typical of kW fibre laser systems. Through several different experiments we present the first demonstration of a cladding pumped aluminium-coated fibre laser and the first demonstration of efficient operation of a cladding-pumped fibre laser at temperatures of greater than 400 °C. Finally, we highlight the versatility of this approach through operation of a passively (radiatively) cooled ytterbium fibre laser head at an output power of 405 W in a compact and ultralight package weighing less than 100 g. PMID:27505822

  6. Spacecraft Thermal Management

    NASA Technical Reports Server (NTRS)

    Hurlbert, Kathryn Miller

    2009-01-01

    In the 21st century, the National Aeronautics and Space Administration (NASA), the Russian Federal Space Agency, the National Space Agency of Ukraine, the China National Space Administration, and many other organizations representing spacefaring nations shall continue or newly implement robust space programs. Additionally, business corporations are pursuing commercialization of space for enabling space tourism and capital business ventures. Future space missions are likely to include orbiting satellites, orbiting platforms, space stations, interplanetary vehicles, planetary surface missions, and planetary research probes. Many of these missions will include humans to conduct research for scientific and terrestrial benefits and for space tourism, and this century will therefore establish a permanent human presence beyond Earth s confines. Other missions will not include humans, but will be autonomous (e.g., satellites, robotic exploration), and will also serve to support the goals of exploring space and providing benefits to Earth s populace. This section focuses on thermal management systems for human space exploration, although the guiding principles can be applied to unmanned space vehicles as well. All spacecraft require a thermal management system to maintain a tolerable thermal environment for the spacecraft crew and/or equipment. The requirements for human rating and the specified controlled temperature range (approximately 275 K - 310 K) for crewed spacecraft are unique, and key design criteria stem from overall vehicle and operational/programatic considerations. These criteria include high reliability, low mass, minimal power requirements, low development and operational costs, and high confidence for mission success and safety. This section describes the four major subsystems for crewed spacecraft thermal management systems, and design considerations for each. Additionally, some examples of specialized or advanced thermal system technologies are presented

  7. Intelligent fault management for the Space Station active thermal control system

    NASA Technical Reports Server (NTRS)

    Hill, Tim; Faltisco, Robert M.

    1992-01-01

    The Thermal Advanced Automation Project (TAAP) approach and architecture is described for automating the Space Station Freedom (SSF) Active Thermal Control System (ATCS). The baseline functionally and advanced automation techniques for Fault Detection, Isolation, and Recovery (FDIR) will be compared and contrasted. Advanced automation techniques such as rule-based systems and model-based reasoning should be utilized to efficiently control, monitor, and diagnose this extremely complex physical system. TAAP is developing advanced FDIR software for use on the SSF thermal control system. The goal of TAAP is to join Knowledge-Based System (KBS) technology, using a combination of rules and model-based reasoning, with conventional monitoring and control software in order to maximize autonomy of the ATCS. TAAP's predecessor was NASA's Thermal Expert System (TEXSYS) project which was the first large real-time expert system to use both extensive rules and model-based reasoning to control and perform FDIR on a large, complex physical system. TEXSYS showed that a method is needed for safely and inexpensively testing all possible faults of the ATCS, particularly those potentially damaging to the hardware, in order to develop a fully capable FDIR system. TAAP therefore includes the development of a high-fidelity simulation of the thermal control system. The simulation provides realistic, dynamic ATCS behavior and fault insertion capability for software testing without hardware related risks or expense. In addition, thermal engineers will gain greater confidence in the KBS FDIR software than was possible prior to this kind of simulation testing. The TAAP KBS will initially be a ground-based extension of the baseline ATCS monitoring and control software and could be migrated on-board as additional computation resources are made available.

  8. Thermally Activated Driver

    NASA Technical Reports Server (NTRS)

    Kinard, William H.; Murray, Robert C.; Walsh, Robert F.

    1987-01-01

    Space-qualified, precise, large-force, thermally activated driver (TAD) developed for use in space on astro-physics experiment to measure abundance of rare actinide-group elements in cosmic rays. Actinide cosmic rays detected using thermally activated driver as heart of event-thermometer (ET) system. Thermal expansion and contraction of silicone oil activates driver. Potential applications in fluid-control systems where precise valve controls are needed.

  9. Integrated failure detection and management for the Space Station Freedom external active thermal control system

    NASA Astrophysics Data System (ADS)

    Mesloh, Nick; Hill, Tim; Kosyk, Kathy

    This paper presents the integrated approach toward failure detection, isolation, and recovery/reconfiguration to be used for the Space Station Freedom External Active Thermal Control System (EATCS). The on-board and on-ground diagnostic capabilities of the EATCS are discussed. Time and safety critical features, as well as noncritical failures, and the detection coverage for each provided by existing capabilities are reviewed. The allocation of responsibility between on-board software and ground-based systems, to be shown during ground testing at the Johnson Space Center, is described. Failure isolation capabilities allocated to the ground include some functionality originally found on orbit but moved to the ground to reduce on-board resource requirements. Complex failures requiring the analysis of multiple external variables, such as environmental conditions, heat loads, or station attitude, are also allocated to ground personnel.

  10. Integrated failure detection and management for the Space Station Freedom external active thermal control system

    NASA Technical Reports Server (NTRS)

    Mesloh, Nick; Hill, Tim; Kosyk, Kathy

    1993-01-01

    This paper presents the integrated approach toward failure detection, isolation, and recovery/reconfiguration to be used for the Space Station Freedom External Active Thermal Control System (EATCS). The on-board and on-ground diagnostic capabilities of the EATCS are discussed. Time and safety critical features, as well as noncritical failures, and the detection coverage for each provided by existing capabilities are reviewed. The allocation of responsibility between on-board software and ground-based systems, to be shown during ground testing at the Johnson Space Center, is described. Failure isolation capabilities allocated to the ground include some functionality originally found on orbit but moved to the ground to reduce on-board resource requirements. Complex failures requiring the analysis of multiple external variables, such as environmental conditions, heat loads, or station attitude, are also allocated to ground personnel.

  11. Advanced thermal management technologies for defense electronics

    NASA Astrophysics Data System (ADS)

    Bloschock, Kristen P.; Bar-Cohen, Avram

    2012-05-01

    Thermal management technology plays a key role in the continuing miniaturization, performance improvements, and higher reliability of electronic systems. For the past decade, and particularly, the past 4 years, the Defense Advanced Research Projects Agency (DARPA) has aggressively pursued the application of micro- and nano-technology to reduce or remove thermal constraints on the performance of defense electronic systems. The DARPA Thermal Management Technologies (TMT) portfolio is comprised of five technical thrust areas: Thermal Ground Plane (TGP), Microtechnologies for Air-Cooled Exchangers (MACE), NanoThermal Interfaces (NTI), Active Cooling Modules (ACM), and Near Junction Thermal Transport (NJTT). An overview of the TMT program will be presented with emphasis on the goals and status of these efforts relative to the current State-of-the-Art. The presentation will close with future challenges and opportunities in the thermal management of defense electronics.

  12. Methods of forming thermal management systems and thermal management methods

    DOEpatents

    Gering, Kevin L.; Haefner, Daryl R.

    2012-06-05

    A thermal management system for a vehicle includes a heat exchanger having a thermal energy storage material provided therein, a first coolant loop thermally coupled to an electrochemical storage device located within the first coolant loop and to the heat exchanger, and a second coolant loop thermally coupled to the heat exchanger. The first and second coolant loops are configured to carry distinct thermal energy transfer media. The thermal management system also includes an interface configured to facilitate transfer of heat generated by an internal combustion engine to the heat exchanger via the second coolant loop in order to selectively deliver the heat to the electrochemical storage device. Thermal management methods are also provided.

  13. Thermal management systems and methods

    DOEpatents

    Gering, Kevin L.; Haefner, Daryl R.

    2006-12-12

    A thermal management system for a vehicle includes a heat exchanger having a thermal energy storage material provided therein, a first coolant loop thermally coupled to an electrochemical storage device located within the first coolant loop and to the heat exchanger, and a second coolant loop thermally coupled to the heat exchanger. The first and second coolant loops are configured to carry distinct thermal energy transfer media. The thermal management system also includes an interface configured to facilitate transfer of heat generated by an internal combustion engine to the heat exchanger via the second coolant loop in order to selectively deliver the heat to the electrochemical storage device. Thermal management methods are also provided.

  14. Nanofluids for vehicle thermal management.

    SciTech Connect

    Choi, S. U.-S.; Yu, W.; Hull, J. R.; Zhang, Z. G.; Lockwood, F. E.; Energy Technology; The Valvoline Co.

    2003-01-01

    Applying nanotechnology to thermal engineering, ANL has addressed the interesting and timely topic of nanofluids. We have developed methods for producing both oxide and metal nanofluids, studied their thermal conductivity, and obtained promising results: (1) Stable suspensions of nanoparticles can be achieved. (2) Nanofluids have significantly higher thermal conductivities than their base liquids. (3) Measured thermal conductivities of nanofluids are much greater than predicted. For these reasons, nanofluids show promise for improving the design and performance of vehicle thermal management systems. However, critical barriers to further development and application of nanofluid technology are agglomeration of nanoparticles and oxidation of metallic nanoparticles. Therefore, methods to prevent particle agglomeration and degradation are required.

  15. Active-mirror-laser-amplifier thermal management with tunable helium pressure at cryogenic temperatures.

    PubMed

    Lucianetti, Antonio; Albach, Daniel; Chanteloup, Jean-Christophe

    2011-06-20

    We illustrate the benefits of a thin, low pressure helium cell for efficient and safe heat removal in cryogenically-cooled active mirror laser amplifiers operating in the [100 J-1 kJ]/[1-10 Hz] range. A homogeneous gain medium temperature distribution averaging 160 K is obtained with a sub-mm helium-filled gap between the gain medium and a copper plate at 77 K. A significant degree of flexibility for tuning the temperature in the amplifier can be achieved by varying the pressure of the helium gas in the 10(2) to 10(5) Pa range. PMID:21716519

  16. Energy Efficient Thermal Management for Natural Gas Engine Aftertreatment via Active Flow Control

    SciTech Connect

    David K. Irick; Ke Nguyen; Vitacheslav Naoumov; Doug Ferguson

    2006-04-01

    The project is focused on the development of an energy efficient aftertreatment system capable of reducing NOx and methane by 90% from lean-burn natural gas engines by applying active exhaust flow control. Compared to conventional passive flow-through reactors, the proposed scheme cuts supplemental energy by 50%-70%. The system consists of a Lean NOx Trap (LNT) system and an oxidation catalyst. Through alternating flow control, a major amount of engine exhaust flows through a large portion of the LNT system in the absorption mode, while a small amount of exhaust goes through a small portion of the LNT system in the regeneration or desulfurization mode. By periodically reversing the exhaust gas flow through the oxidation catalyst, a higher temperature profile is maintained in the catalyst bed resulting in greater efficiency of the oxidation catalyst at lower exhaust temperatures. The project involves conceptual design, theoretical analysis, computer simulation, prototype fabrication, and empirical studies. This report details the progress during the first twelve months of the project. The primary activities have been to develop the bench flow reactor system, develop the computer simulation and modeling of the reverse-flow oxidation catalyst, install the engine into the test cell, and begin design of the LNT system.

  17. Energy Efficient Thermal Management for Natural Gas Engine Aftertreatment via Active Flow Control

    SciTech Connect

    David K. Irick; Ke Nguyen; Vitacheslav Naoumov; Doug Ferguson

    2005-04-01

    The project is focused on the development of an energy efficient aftertreatment system capable of reducing NOx and methane by 90% from lean-burn natural gas engines by applying active exhaust flow control. Compared to conventional passive flow-through reactors, the proposed scheme cuts supplemental energy by 50%-70%. The system consists of a Lean NOx Trap (LNT) system and an oxidation catalyst. Through alternating flow control, a major amount of engine exhaust flows through a large portion of the LNT system in the absorption mode, while a small amount of exhaust goes through a small portion of the LNT system in the regeneration or desulfurization mode. By periodically reversing the exhaust gas flow through the oxidation catalyst, a higher temperature profile is maintained in the catalyst bed resulting in greater efficiency of the oxidation catalyst at lower exhaust temperatures. The project involves conceptual design, theoretical analysis, computer simulation, prototype fabrication, and empirical studies. This report details the progress during the first twelve months of the project. The primary activities have been to develop the bench flow reactor system, develop the computer simulation and modeling of the reverse-flow oxidation catalyst, install the engine into the test cell, and begin design of the LNT system.

  18. ENERGY EFFICIENT THERMAL MANAGEMENT FOR NATURAL GAS ENGINE AFTERTREATMENT VIA ACTIVE FLOW CONTROL

    SciTech Connect

    David K. Irick; Ke Nguyen

    2004-04-01

    The project is focused on the development of an energy efficient aftertreatment system capable of reducing NOx and methane by 90% from lean-burn natural gas engines by applying active exhaust flow control. Compared to conventional passive flow-through reactors, the proposed scheme cuts supplemental energy by 50%-70%. The system consists of a Lean NOx Trap (LNT) system and an oxidation catalyst. Through alternating flow control, a major amount of engine exhaust flows through a large portion of the LNT system in the absorption mode, while a small amount of exhaust goes through a small portion of the LNT system in the regeneration or desulfurization mode. By periodically reversing the exhaust gas flow through the oxidation catalyst, a higher temperature profile is maintained in the catalyst bed resulting in greater efficiency of the oxidation catalyst at lower exhaust temperatures. The project involves conceptual design, theoretical analysis, computer simulation, prototype fabrication, and empirical studies. This report details the progress during the first twelve months of the project. The primary activities have been to develop the bench flow reactor system, develop the computer simulation and modeling of the reverse-flow oxidation catalyst, install the engine into the test cell, and begin design of the LNT system.

  19. Atomizer for thermal management system

    NASA Technical Reports Server (NTRS)

    Tilton, Charles L. (Inventor); Weiler, Jeff (Inventor); Palmer, Randal T. (Inventor); Appel, Philip W. (Inventor); Knight, Paul A. (Inventor)

    2008-01-01

    An atomizer for thermal management system for efficiently thermally managing one or more heat producing devices. The atomizer for thermal management system includes a housing having a coolant passage and a dispensing end, an orifice within the dispensing end, and an actuator manipulating a plunger within the housing. The plunger includes a head that is sealable within a recessed portion of the orifice to open or close the orifice. The coolant passes through the coolant passage into the orifice for spraying upon a heat producing device. The actuator may reciprocate so that the coolant spray emitted through the orifice is pulsating. The pulsing frequency may be increased to increase cooling or decreased to decrease cooling of the heat producing device.

  20. Thermal Management of Light Sources

    NASA Astrophysics Data System (ADS)

    Hartmann, J.; Völker, Stephan

    2011-01-01

    The primary task of light sources is illumination, i.e., the emission of visible radiation—light. However, depending on the generation principle, besides light, also heat will be dissipated to the surroundings. Traditional thermal light sources generate light by the electrical heating of a tungsten wire to temperatures of about 3000 K. Even at this high temperature, the majority of the emitted thermal radiation is within the long wavelength range of the spectrum, i.e., not in the visible range of the optical spectrum. Generation of light with discharge lamps is completely different and non-thermal; however, even in this case the electrodes are heated to temperatures well above 2000 K. Thus, discharge lamps also suffer from thermal problems. In the case of solid-state light sources, also non-thermal light sources, the driving electrical current causes heating of the device, for which the temperature is, or should usually be, below 420 K for proper operation. Contrary to thermal or discharge light sources, such relatively low temperatures of solid-state light sources prevent efficient cooling by thermal radiation, requiring convective or conductive cooling. However, for all mentioned light sources, the thermal management, i.e., the adjusting and maintaining of an optimum operation temperature are vital for the efficiency and lifetime of the light sources. This paper deals with the methods of generation and measurement of the thermal load in the respective light sources and discusses ways to optimize the efficiency and lifetime of such light sources. Also, some practical examples are given to emphasize the relevance of such thermal management for industry, pointing out the potential for future more energy-efficient light source concepts.

  1. Actively driven thermal radiation shield

    DOEpatents

    Madden, Norman W.; Cork, Christopher P.; Becker, John A.; Knapp, David A.

    2002-01-01

    A thermal radiation shield for cooled portable gamma-ray spectrometers. The thermal radiation shield is located intermediate the vacuum enclosure and detector enclosure, is actively driven, and is useful in reducing the heat load to mechanical cooler and additionally extends the lifetime of the mechanical cooler. The thermal shield is electrically-powered and is particularly useful for portable solid-state gamma-ray detectors or spectrometers that dramatically reduces the cooling power requirements. For example, the operating shield at 260K (40K below room temperature) will decrease the thermal radiation load to the detector by 50%, which makes possible portable battery operation for a mechanically cooled Ge spectrometer.

  2. Thermoelectric Devices Advance Thermal Management

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Thermoelectric (TE) devices heat, cool, and generate electricity when a temperature differential is provided between the two module faces. In cooperation with NASA, Chico, California-based United States Thermoelectric Consortium Inc. (USTC) built a gas emissions analyzer (GEA) for combustion research. The GEA precipitated hydrocarbon particles, preventing contamination that would hinder precise rocket fuel analysis. The USTC research and design team uses patent-pending dimple, pin-fin, microchannel and microjet structures to develop and design heat dissipation devices on the mini-scale level, which not only guarantee high performance of products, but also scale device size from 1 centimeter to 10 centimeters. USTC continues to integrate the benefits of TE devices in its current line of thermal management solutions and has found the accessibility of NASA technical research to be a valuable, sustainable resource that has continued to positively influence its product design and manufacturing

  3. Thermally activated technologies: Technology Roadmap

    SciTech Connect

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  4. Thermal energy management process experiment

    NASA Technical Reports Server (NTRS)

    Ollendorf, S.

    1984-01-01

    The thermal energy management processes experiment (TEMP) will demonstrate that through the use of two-phase flow technology, thermal systems can be significantly enhanced by increasing heat transport capabilities at reduced power consumption while operating within narrow temperature limits. It has been noted that such phenomena as excess fluid puddling, priming, stratification, and surface tension effects all tend to mask the performance of two-phase flow systems in a 1-g field. The flight experiment approach would be to attack the experiment to an appropriate mounting surface with a 15 to 20 meter effective length and provide a heat input and output station in the form of heaters and a radiator. Using environmental data, the size, location, and orientation of the experiment can be optimized. The approach would be to provide a self-contained panel and mount it to the STEP through a frame. A small electronics package would be developed to interface with the STEP avionics for command and data handling. During the flight, heaters on the evaporator will be exercised to determine performance. Flight data will be evaluated against the ground tests to determine any anomalous behavior.

  5. Understanding thermal equilibrium through activities

    NASA Astrophysics Data System (ADS)

    Pathare, Shirish; Huli, Saurabhee; Nachane, Madhura; Ladage, Savita; Pradhan, Hemachandra

    2015-03-01

    Thermal equilibrium is a basic concept in thermodynamics. In India, this concept is generally introduced at the first year of undergraduate education in physics and chemistry. In our earlier studies (Pathare and Pradhan 2011 Proc. episteme-4 Int. Conf. to Review Research on Science Technology and Mathematics Education pp 169-72) we found that students in India have a rather unsatisfactory understanding of thermal equilibrium. We have designed and developed a module of five activities, which are presented in succession to the students. These activities address the students’ alternative conceptions that underlie their lack of understanding of thermal equilibrium and aim at enhancing their understanding of the concept.

  6. Thermal start-up behaviour and thermal management of SOFC's

    NASA Astrophysics Data System (ADS)

    Apfel, H.; Rzepka, M.; Tu, H.; Stimming, U.

    Solid oxide fuel cells (SOFCs) have many attractive features for widespread applications. The high operating temperature provides a valuable heat source and in contrast to low temperature fuel cells they not only tolerate substances such as CO but can even use them as fuel. Thus, reforming of hydrocarbon fuels for SOFCs can be done without additional gas purification. As both stack and hydrocarbon reformer unit have to be operated at high temperatures (700-1000 °C), thermal management plays an important role in the successful operation of SOFC systems. As the SOFC system contains ceramic components, both large thermal gradients in the system and thermal expansion coefficient (TEC) mismatch must be avoided. Matching TECs is done by selecting the suitable materials. Avoiding high temperature gradients is done by selecting the right system design and control strategies. In order to achieve both, we have built a finite element simulation for a complete SOFC systems which allows to study system parameters both during steady operation and during transients. Examples of the thermal start-up behaviour for several system configurations are given for selected components as well as internal temperatures of the SOFC-stack during start-up. The simulation model includes also the option to simulate the effects of internal methane reformation in the SOFC stack. As the minimum operation temperature is high, cooling down of the system has to be avoided if instant operation is desired. This can be achieved either passively by selecting suitable thermal insulation materials and/or actively by adopting a strategy for maintaining the temperature.

  7. Active thermal extraction of near-field thermal radiation

    NASA Astrophysics Data System (ADS)

    Ding, D.; Kim, T.; Minnich, A. J.

    2016-02-01

    Radiative heat transport between materials supporting surface-phonon polaritons is greatly enhanced when the materials are placed at subwavelength separation as a result of the contribution of near-field surface modes. However, the enhancement is limited to small separations due to the evanescent decay of the surface waves. In this work, we propose and numerically demonstrate an active scheme to extract these modes to the far field. Our approach exploits the monochromatic nature of near-field thermal radiation to drive a transition in a laser gain medium, which, when coupled with external optical pumping, allows the resonant surface mode to be emitted into the far field. Our study demonstrates an approach to manipulate thermal radiation that could find applications in thermal management.

  8. Lighting system with thermal management system

    SciTech Connect

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Seeley, Charles Erklin; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Utturkar, Yogen Vishwas; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2015-08-25

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  9. Lighting system with thermal management system

    DOEpatents

    Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2013-05-07

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  10. Lighting system with thermal management system

    DOEpatents

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Seeley, Charles Erklin; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Utturkar, Yogen Vishwas; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2015-02-24

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  11. Student Activities. Managing Liability.

    ERIC Educational Resources Information Center

    Bennett, Barbara; And Others

    This monograph suggests ways that college or university administrations can undertake a systematic and careful review of the risks posed by students' activities. Its purpose is to provide guidance in integrating the risk management process into a school's existing approaches to managing student organizations and activities. It is noted that no…

  12. Active (air-cooled) vs. passive (phase change material) thermal management of high power lithium-ion packs: Limitation of temperature rise and uniformity of temperature distribution

    NASA Astrophysics Data System (ADS)

    Sabbah, Rami; Kizilel, R.; Selman, J. R.; Al-Hallaj, S.

    The effectiveness of passive cooling by phase change materials (PCM) is compared with that of active (forced air) cooling. Numerical simulations were performed at different discharge rates, operating temperatures and ambient temperatures of a compact Li-ion battery pack suitable for plug-in hybrid electric vehicle (PHEV) propulsion. The results were also compared with experimental results. The PCM cooling mode uses a micro-composite graphite-PCM matrix surrounding the array of cells, while the active cooling mode uses air blown through the gaps between the cells in the same array. The results show that at stressful conditions, i.e. at high discharge rates and at high operating or ambient temperatures (for example 40-45 °C), air-cooling is not a proper thermal management system to keep the temperature of the cell in the desirable operating range without expending significant fan power. On the other hand, the passive cooling system is able to meet the operating range requirements under these same stressful conditions without the need for additional fan power.

  13. Thermal management of LEDs: package to system

    NASA Astrophysics Data System (ADS)

    Arik, Mehmet; Becker, Charles A.; Weaver, Stanton E.; Petroski, James

    2004-01-01

    Light emitting diodes, LEDs, historically have been used for indicators and produced low amounts of heat. The introduction of high brightness LEDs with white light and monochromatic colors have led to a movement towards general illumination. The increased electrical currents used to drive the LEDs have focused more attention on the thermal paths in the developments of LED power packaging. The luminous efficiency of LEDs is soon expected to reach over 80 lumens/W, this is approximately 6 times the efficiency of a conventional incandescent tungsten bulb. Thermal management for the solid-state lighting applications is a key design parameter for both package and system level. Package and system level thermal management is discussed in separate sections. Effect of chip packages on junction to board thermal resistance was compared for both SiC and Sapphire chips. The higher thermal conductivity of the SiC chip provided about 2 times better thermal performance than the latter, while the under-filled Sapphire chip package can only catch the SiC chip performance. Later, system level thermal management was studied based on established numerical models for a conceptual solid-state lighting system. A conceptual LED illumination system was chosen and CFD models were created to determine the availability and limitations of passive air-cooling.

  14. Thermal energy storage chiller management

    SciTech Connect

    Williams, C.D.

    1996-11-01

    This paper addresses chiller applications that are designed to get the maximum benefit form a chiller plant every day of the year. It treats all chillers as variable-capacity devices and applies them in thermal storage system configurations that efficiently take advantage of that capability. It also recognizes that a chiller operating temperature differential is always a variable to which a chiller must always adjust. All the applications addressed vary the flow and in some situations the operating temperature differential to maximize or optimize each chiller`s capacity. It is done in such a manner that the safety and reliability of the chiller are improved rather than jeopardized.

  15. Experimental study on active cooling systems used for thermal management of high-power multichip light-emitting diodes.

    PubMed

    Kaya, Mehmet

    2014-01-01

    The objective of this study was to develop suitable cooling systems for high-power multichip LEDs. To this end, three different active cooling systems were investigated to control the heat generated by the powering of high-power multichip LEDs in two different configurations (30 and 2 × 15 W). The following cooling systems were used in the study: an integrated multi-fin heat sink design with a fan, a cooling system with a thermoelectric cooler (TEC), and a heat pipe cooling device. According to the results, all three systems were observed to be sufficient for cooling high-power LEDs. Furthermore, it was observed that the integrated multifin heat sink design with a fan was the most efficient cooling system for a 30 W high-power multichip LED. The cooling system with a TEC and 46 W input power was the most efficient cooling system for 2 × 15 W high-power multichip LEDs. PMID:25162058

  16. Experimental Study on Active Cooling Systems Used for Thermal Management of High-Power Multichip Light-Emitting Diodes

    PubMed Central

    2014-01-01

    The objective of this study was to develop suitable cooling systems for high-power multichip LEDs. To this end, three different active cooling systems were investigated to control the heat generated by the powering of high-power multichip LEDs in two different configurations (30 and 2 × 15 W). The following cooling systems were used in the study: an integrated multi-fin heat sink design with a fan, a cooling system with a thermoelectric cooler (TEC), and a heat pipe cooling device. According to the results, all three systems were observed to be sufficient for cooling high-power LEDs. Furthermore, it was observed that the integrated multifin heat sink design with a fan was the most efficient cooling system for a 30 W high-power multichip LED. The cooling system with a TEC and 46 W input power was the most efficient cooling system for 2 × 15 W high-power multichip LEDs. PMID:25162058

  17. Micro-Scale Avionics Thermal Management

    NASA Technical Reports Server (NTRS)

    Moran, Matthew E.

    2001-01-01

    Trends in the thermal management of avionics and commercial ground-based microelectronics are converging, and facing the same dilemma: a shortfall in technology to meet near-term maximum junction temperature and package power projections. Micro-scale devices hold the key to significant advances in thermal management, particularly micro-refrigerators/coolers that can drive cooling temperatures below ambient. A microelectromechanical system (MEMS) Stirling cooler is currently under development at the NASA Glenn Research Center to meet this challenge with predicted efficiencies that are an order of magnitude better than current and future thermoelectric coolers.

  18. Thermal Cameras in School Laboratory Activities

    ERIC Educational Resources Information Center

    Haglund, Jesper; Jeppsson, Fredrik; Hedberg, David; Schönborn, Konrad J.

    2015-01-01

    Thermal cameras offer real-time visual access to otherwise invisible thermal phenomena, which are conceptually demanding for learners during traditional teaching. We present three studies of students' conduction of laboratory activities that employ thermal cameras to teach challenging thermal concepts in grades 4, 7 and 10-12. Visualization of…

  19. Prolonging thermal barrier coated specimen life by thermal cycle management

    NASA Technical Reports Server (NTRS)

    Hendricks, R. C.; Mcdonald, G.; Poolos, N. P.

    1981-01-01

    Thermal barrier coatings applied to the heated side of engine components such as seals, combustor, and blades of a gas turbine offer a potential increase in efficiency through the use of higher gas temperatures or less cooling air or benefits arising from extended component life by reducing component metal temperatures. The considered investigation has the objective to show that while a thermal barrier coated (TBC) specimen can be brought to a fixed temperature using various fuel-air ratio (F/A) values, lower calculated stresses are associated with lower (F/A) values. This implies that control of (F/A) values (i.e., rates of heat input) during the starting transient and to a lesser extent during shutdown and operation, offers a potential method of improving TBC lifetime through thermal cycle management.

  20. Active Thermal Control System Development for Exploration

    NASA Technical Reports Server (NTRS)

    Westheimer, David

    2007-01-01

    All space vehicles or habitats require thermal management to maintain a safe and operational environment for both crew and hardware. Active Thermal Control Systems (ATCS) perform the functions of acquiring heat from both crew and hardware within a vehicle, transporting that heat throughout the vehicle, and finally rejecting that energy into space. Almost all of the energy used in a space vehicle eventually turns into heat, which must be rejected in order to maintain an energy balance and temperature control of the vehicle. For crewed vehicles, Active Thermal Control Systems are pumped fluid loops that are made up of components designed to perform these functions. NASA has been actively developing technologies that will enable future missions or will provide significant improvements over the state of the art technologies. These technologies have are targeted for application on the Crew Exploration Vehicle (CEV), or Orion, and a Lunar Surface Access Module (LSAM). The technologies that have been selected and are currently under development include: fluids that enable single loop ATCS architectures, a gravity insensitive vapor compression cycle heat pump, a sublimator with reduced sensitivity to feedwater contamination, an evaporative heat sink that can operate in multiple ambient pressure environments, a compact spray evaporator, and lightweight radiators that take advantage of carbon composites and advanced optical coatings.

  1. Integrated Vehicle Thermal Management for Advanced Vehicle Propulsion Technologies

    SciTech Connect

    Bennion, K.; Thornton, M.

    2010-04-01

    A critical element to the success of new propulsion technologies that enable reductions in fuel use is the integration of component thermal management technologies within a viable vehicle package. Vehicle operation requires vehicle thermal management systems capable of balancing the needs of multiple vehicle systems that may require heat for operation, require cooling to reject heat, or require operation within specified temperature ranges. As vehicle propulsion transitions away from a single form of vehicle propulsion based solely on conventional internal combustion engines (ICEs) toward a wider array of choices including more electrically dominant systems such as plug-in hybrid electric vehicles (PHEVs), new challenges arise associated with vehicle thermal management. As the number of components that require active thermal management increase, so do the costs in terms of dollars, weight, and size. Integrated vehicle thermal management is one pathway to address the cost, weight, and size challenges. The integration of the power electronics and electric machine (PEEM) thermal management with other existing vehicle systems is one path for reducing the cost of electric drive systems. This work demonstrates techniques for evaluating and quantifying the integrated transient and continuous heat loads of combined systems incorporating electric drive systems that operate primarily under transient duty cycles, but the approach can be extended to include additional steady-state duty cycles typical for designing vehicle thermal management systems of conventional vehicles. The work compares opportunities to create an integrated low temperature coolant loop combining the power electronics and electric machine with the air conditioning system in contrast to a high temperature system integrated with the ICE cooling system.

  2. Graphite Foam Heat Exchangers for Thermal Management

    SciTech Connect

    Klett, J.W.

    2004-06-07

    Improved thermal management is needed to increase the power density of electronic and more effectively cool electronic enclosures that are envisioned in future aircraft, spacecraft and surface ships. Typically, heat exchanger cores must increase in size to more effectively dissipate increased heat loads, this would be impossible in many cases, thus improved heat exchanger cores will be required. In this Phase I investigation, MRi aimed to demonstrate improved thermal management using graphite foam (Gr-foam) core heat exchangers. The proposed design was to combine Gr-foams from POCO with MRi's innovative low temperature, active metal joining process (S-Bond{trademark}) to bond Gr-foam to aluminum, copper and aluminum/SiC composite faceplates. The results were very favorable, so a Phase II SBIR with the MDA was initiated. This had primarily 5 tasks: (1) bonding, (2) thermal modeling, (3) cooling chip scale packages, (4) evaporative cooling techniques and (5) IGBT cold plate development. The bonding tests showed that the ''reflow'' technique with S-Bond{reg_sign}-220 resulted in the best and most consistent bond. Then, thermal modeling was used to design different chip scale packages and IGBT cold plates. These designs were used to fabricate many finned graphite foam heat sinks specifically for two standard type IC packages, the 423 and 478 pin chips. These results demonstrated several advantages with the foam. First, the heat sinks with the foam were lighter than the copper/aluminum sinks used as standards. The sinks for the 423 design made from foam were not as good as the standard sinks. However, the sinks made from foam for the 478 pin chips were better than the standard heat sinks used today. However, this improvement was marginal (in the 10-20% better regime). However, another important note was that the epoxy bonding technique resulted in heat sinks with similar results as that with the S-bond{reg_sign}, slightly worse than the S-bond{reg_sign}, but still

  3. Passive Thermal Management of Foil Bearings

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert J. (Inventor)

    2015-01-01

    Systems and methods for passive thermal management of foil bearing systems are disclosed herein. The flow of the hydrodynamic film across the surface of bearing compliant foils may be disrupted to provide passive cooling and to improve the performance and reliability of the foil bearing system.

  4. Advanced thermal management needs for Lunar and Mars missions

    SciTech Connect

    Klein, A.C. ); Webb, B.J. )

    1993-01-15

    Significant improvements in thermal management technologies will be required to support NASA's planned Lunar and Mars missions. The developments needed include the application of advanced materials to reduce radiator system masses, enhanced survivability, and the use of alternative working fluids. Current thermal management systems utilize one of two heat rejection alternatives; either single phase pumped loops, or two phase heat pipes constructed with thick walled metal casings. These two technologies have proven themselves to be reliable performers in the transport and rejection of waste heat from spacecraft. As thermal management needs increase with increased power consumption and activity required on spacecraft, these metal based thermal management systems will become mission limiting. Investigations into the use of light weight ceramic materials for high temperature thermal management systems have been conducted by NASA, the Department of Energy, and the Department of Defense since the early 1980s, with results showing that significant mass savings can be obtained by replacing some of the metallic functions with ceramic materials.

  5. Electric Motor Thermal Management R&D (Presentation)

    SciTech Connect

    Bennion, K.

    2014-11-01

    Thermal constraints place significant limitations on how electric motors ultimately perform. Without the ability to remove heat, the motor cannot operate without sacrificing performance, efficiency, and reliability. Finite element analysis and computational fluid dynamics modeling approaches are being increasingly utilized in the design and analysis of electric motors. As the models become more sophisticated, it is important to have detailed and accurate knowledge of both the passive thermal performance and the active cooling performance. In this work, we provide an overview of research characterizing both passive and active thermal elements related to electric motor thermal management. To better characterize the passive thermal performance, the effective thermal properties and inter-lamination thermal contact resistances were measured for different stator lamination materials. The active cooling performance of automatic transmission fluid (ATF) jets was also measured to better understand the heat transfer coefficients of ATF impinging on motor copper windings. Ford's Mercon LV was the ATF evaluated in this study. The presentation provides an overview of prior work with a focus on describing future plans for research to be performed during FY15.

  6. Active thermal control system evolution

    NASA Technical Reports Server (NTRS)

    Petete, Patricia A.; Ames, Brian E.

    1991-01-01

    The 'restructured' baseline of the Space Station Freedom (SSF) has eliminated many of the growth options for the Active Thermal Control System (ATCS). Modular addition of baseline technology to increase heat rejection will be extremely difficult. The system design and the available real estate no longer accommodate this type of growth. As the station matures during its thirty years of operation, a demand of up to 165 kW of heat rejection can be expected. The baseline configuration will be able to provide 82.5 kW at Eight Manned Crew Capability (EMCC). The growth paths necessary to reach 165 kW have been identified. Doubling the heat rejection capability of SSF will require either the modification of existing radiator wings or the attachment of growth structure to the baseline truss for growth radiator wing placement. Radiator performance can be improved by enlarging the surface area or by boosting the operating temperature with a heat pump. The optimal solution will require both modifications. The addition of growth structure would permit the addition of a parallel ATCS using baseline technology. This growth system would simplify integration. The feasibility of incorporating these growth options to improve the heat rejection capacity of SSF is under evaluation.

  7. Development and Evaluation of Active Thermal Management System for Lithium-Ion Batteries using Solid-State Thermoelectric Heat Pump and Heat Pipes with Electric Vehicular Applications

    NASA Astrophysics Data System (ADS)

    Parekh, Bhaumik Kamlesh

    Lithium-Ion batteries have become a popular choice for use in energy storage systems in electric vehicles (EV) and Hybrid electric vehicles (HEV) because of high power and high energy density. But the use of EV and HEV in all climates demands for a battery thermal management system (BTMS) since temperature effects their performance, cycle life and, safety. Hence the BTMS plays a crucial role in the performance of EV and HEV. In this paper, three thermal management systems are studied: (a) simple aluminum as heat spreader material, (b) heat pipes as heat spreader, and (c) advanced combined solid state thermoelectric heat pump (TE) and heat pipe system; these will be subsequently referred to as Design A, B and C, respectively. A detailed description of the designs and the experimental setup is presented. The experimental procedure is divided into two broad categories: Cooling mode and Warming-up mode. Cooling mode covers the conditions when a BTMS is responsible to cool the battery pack through heat dissipation and Warming-up mode covers the conditions when the BTMS is responsible to warm the battery pack in a low temperature ambient condition, maintaining a safe operating temperature of the battery pack in both modes. The experimental procedure analyzes the thermal management system by evaluating the effect of each variable like heat sink area, battery heat generation rate, cooling air temperature, air flow rate and TE power on parameters like maximum temperature of the battery pack (T max), maximum temperature difference (DeltaT) and, heat transfer through heat sink/cooling power of TE (Q c). The results show that Design C outperforms Design A and Design B in spite of design issues which reduce its efficiency, but can still be improved to achieve better performance.

  8. Advanced Devices for Cryogenic Thermal Management

    NASA Astrophysics Data System (ADS)

    Bugby, D.; Stouffer, C.; Garzon, J.; Beres, M.; Gilchrist, A.

    2006-04-01

    This paper describes six advanced cryogenic thermal management devices/subsystems developed by Swales Aerospace for ground/space-based applications of interest to NASA, DoD, and the commercial sector. The devices/subsystems described herein include the following: (a) a differential thermal expansion cryogenic thermal switch (DTE-CTSW) constructed with high purity aluminum end-pieces and an Ultem support rod for the 6 K Mid-Infrared Instrument (MIRI) on the James Webb Space Telescope (JWST) (b) a quad-redundant DTE-CTSW assembly for the 35 K science instruments (NIRCam, NIRSpec, and FGS) mounted on the JWST Integrated Science Instrument Module (ISIM) (c) a cryogenic diode heat pipe (CDHP) thermal switching system using methane as the working fluid for the 100 K CRISM hyperspectral mapping instrument on the Mars Reconnaissance Orbiter (MRO) and (d) three additional devices/subsystems developed during the AFRL-sponsored CRYOTOOL program, which include a dual DTE-CTSW/dual cryocooler test bed, a miniaturized neon cryogenic loop heat pipe (mini-CLHP), and an across gimbal cryogenic thermal transport system (GCTTS). For the first three devices/subsystems mentioned above, this paper describes key aspects of the development efforts including concept definition, design, fabrication, and testing. For the latter three, this paper provides brief overview descriptions as key details are provided in a related paper.

  9. Nanowires for thermal energy conversion and management

    NASA Astrophysics Data System (ADS)

    Chen, Renkun

    This dissertation presents the application of nanowires in two aspects of thermal energy conversion and management: (i) silicon (Si) nanowires as efficient and scalable thermoelectric materials due to the reduced thermal conductivity (k), and (ii) Si and copper (Cu) nanowire arrays for enhanced phase change heat transfer including boiling and evaporation and their applications in thermal management of microelectronics. In the first half of the thesis (chapter 2 and 3), we describe thermal and thermoelectric measurements of individual Si nanowires for studying phonon transport properties and their potential application in thermoelectrics. A theoretical model based on coherent phonon scattering was developed to explain the experiemental data, which suggests that phonon-boundary scattering is highly frequency dependent. For low frequency (long wavelength) phonons, the transport is nearly ballistic, whereas high frequency or short wavelength phonons scatter diffusively at nanowire boundary. The competition between the two phonon transmission regimes results in the unusual linear behavior of the thermal conductance of thin VLS Si nanowires at low temperature. Next, the thermal conductivity of EE Si nanowires, which have much rougher surface compared to VLS nanowires, was measured and found to be five-eight times lower than that of VLS counterparts with similar diameters. The substantial reduction in k is presumably due to the higher surface roughness, since both types of nanowires have single crystalline cores. In particular, for ˜ 50 nm EE Si nanowires etched from 0.1 O-cm B-doped p-Si <111> (˜2 x 1017 cm-3 dopant concentration), the k is around 1.6 Wm-1K-1 and the kL is ˜1.2 Wm-1 K-1 at room temperature, approaching that of amorphous Si. The single nanowire measurements show the great promise of using Si nanowire arrays as high-performance, scalable thermoelectric materials. As the second focus of the thesis (chapter 4 and 5), nanowire arrays were used for enhanced

  10. Thermal Management of Power Electronics and Electric Motors for Electric-Drive Vehicles (Presentation)

    SciTech Connect

    Narumanchi, S.

    2014-09-01

    This presentation is an overview of the power electronics and electric motor thermal management and reliability activities at NREL. The focus is on activities funded by the Department of Energy Vehicle Technologies Office Advanced Power Electronics and Electric Motors Program.

  11. Thermal management concepts for higher efficiency heavy vehicles.

    SciTech Connect

    Wambsganss, M. W.

    1999-05-19

    Thermal management is a cross-cutting technology that directly or indirectly affects engine performance, fuel economy, safety and reliability, aerodynamics, driver/passenger comfort, materials selection, emissions, maintenance, and component life. This review paper provides an assessment of thermal management for large trucks, particularly as it impacts these features. Observations arrived at from a review of the state of the art for thermal management for over-the-road trucks are highlighted and commented on. Trends in the large truck industry, pertinent engine truck design and performance objectives, and the implications of these relative to thermal management, are presented. Finally, new thermal management concepts for high efficiency vehicles are described.

  12. Nanoplasmon-enabled macroscopic thermal management

    NASA Astrophysics Data System (ADS)

    Jonsson, Gustav Edman; Miljkovic, Vladimir; Dmitriev, Alexandre

    2014-05-01

    In numerous applications of energy harvesting via transformation of light into heat the focus recently shifted towards highly absorptive nanoplasmonic materials. It is currently established that noble metals-based absorptive plasmonic platforms deliver significant light-capturing capability and can be viewed as super-absorbers of optical radiation. Naturally, approaches to the direct experimental probing of macroscopic temperature increase resulting from these absorbers are welcomed. Here we derive a general quantitative method of characterizing heat-generating properties of optically absorptive layers via macroscopic thermal imaging. We further monitor macroscopic areas that are homogeneously heated by several degrees with nanostructures that occupy a mere 8% of the surface, leaving it essentially transparent and evidencing significant heat generation capability of nanoplasmon-enabled light capture. This has a direct bearing to a large number of applications where thermal management is crucial.

  13. Nanoplasmon-enabled macroscopic thermal management

    PubMed Central

    Jonsson, Gustav Edman; Miljkovic, Vladimir; Dmitriev, Alexandre

    2014-01-01

    In numerous applications of energy harvesting via transformation of light into heat the focus recently shifted towards highly absorptive nanoplasmonic materials. It is currently established that noble metals-based absorptive plasmonic platforms deliver significant light-capturing capability and can be viewed as super-absorbers of optical radiation. Naturally, approaches to the direct experimental probing of macroscopic temperature increase resulting from these absorbers are welcomed. Here we derive a general quantitative method of characterizing heat-generating properties of optically absorptive layers via macroscopic thermal imaging. We further monitor macroscopic areas that are homogeneously heated by several degrees with nanostructures that occupy a mere 8% of the surface, leaving it essentially transparent and evidencing significant heat generation capability of nanoplasmon-enabled light capture. This has a direct bearing to a large number of applications where thermal management is crucial. PMID:24870613

  14. Stand Alone Battery Thermal Management System

    SciTech Connect

    Brodie, Brad

    2015-09-30

    The objective of this project is research, development and demonstration of innovative thermal management concepts that reduce the cell or battery weight, complexity (component count) and/or cost by at least 20%. The project addresses two issues that are common problems with current state of the art lithium ion battery packs used in vehicles; low power at cold temperatures and reduced battery life when exposed to high temperatures. Typically, battery packs are “oversized” to satisfy the two issues mentioned above. The first phase of the project was spent making a battery pack simulation model using AMEsim software. The battery pack used as a benchmark was from the Fiat 500EV. FCA and NREL provided vehicle data and cell data that allowed an accurate model to be created that matched the electrical and thermal characteristics of the actual battery pack. The second phase involved using the battery model from the first phase and evaluate different thermal management concepts. In the end, a gas injection heat pump system was chosen as the dedicated thermal system to both heat and cool the battery pack. Based on the simulation model. The heat pump system could use 50% less energy to heat the battery pack in -20°C ambient conditions, and by keeping the battery cooler at hot climates, the battery pack size could be reduced by 5% and still meet the warranty requirements. During the final phase, the actual battery pack and heat pump system were installed in a test bench at DENSO to validate the simulation results. Also during this phase, the system was moved to NREL where testing was also done to validate the results. In conclusion, the heat pump system can improve “fuel economy” (for electric vehicle) by 12% average in cold climates. Also, the battery pack size, or capacity, could be reduced 5%, or if pack size is kept constant, the pack life could be increased by two years. Finally, the total battery pack and thermal system cost could be reduced 5% only if the

  15. Understanding Thermal Equilibrium through Activities

    ERIC Educational Resources Information Center

    Pathare, Shirish; Huli, Saurabhee; Nachane, Madhura; Ladage, Savita; Pradhan, Hemachandra

    2015-01-01

    Thermal equilibrium is a basic concept in thermodynamics. In India, this concept is generally introduced at the first year of undergraduate education in physics and chemistry. In our earlier studies (Pathare and Pradhan 2011 "Proc. episteme-4 Int. Conf. to Review Research on Science Technology and Mathematics Education" pp 169-72) we…

  16. Study of thermal management for space platform applications: Unmanned modular thermal management and radiator technologies

    NASA Technical Reports Server (NTRS)

    Oren, J. A.

    1981-01-01

    Candidate techniques for thermal management of unmanned modules docked to a large 250 kW platform were evaluated. Both automatically deployed and space constructed radiator systems were studied to identify characteristics and potential problems. Radiator coating requirements and current state-of-the-art were identified. An assessment of the technology needs was made and advancements were recommended.

  17. Orbiter active thermal control system description

    NASA Technical Reports Server (NTRS)

    Laubach, G. E.

    1975-01-01

    A brief description of the Orbiter Active Thermal Control System (ATCS) including (1) major functional requirements of heat load, temperature control and heat sink utilization, (2) the overall system arrangement, and (3) detailed description of the elements of the ATCS.

  18. Temperature-gated thermal rectifier for active heat flow control.

    PubMed

    Zhu, Jia; Hippalgaonkar, Kedar; Shen, Sheng; Wang, Kevin; Abate, Yohannes; Lee, Sangwook; Wu, Junqiao; Yin, Xiaobo; Majumdar, Arun; Zhang, Xiang

    2014-08-13

    Active heat flow control is essential for broad applications of heating, cooling, and energy conversion. Like electronic devices developed for the control of electric power, it is very desirable to develop advanced all-thermal solid-state devices that actively control heat flow without consuming other forms of energy. Here we demonstrate temperature-gated thermal rectification using vanadium dioxide beams in which the environmental temperature actively modulates asymmetric heat flow. In this three terminal device, there are two switchable states, which can be regulated by global heating. In the "Rectifier" state, we observe up to 28% thermal rectification. In the "Resistor" state, the thermal rectification is significantly suppressed (<1%). To the best of our knowledge, this is the first demonstration of solid-state active-thermal devices with a large rectification in the Rectifier state. This temperature-gated rectifier can have substantial implications ranging from autonomous thermal management of heating and cooling systems to efficient thermal energy conversion and storage. PMID:25010206

  19. Space Station thermal management system development status and plans

    NASA Technical Reports Server (NTRS)

    Rankin, J. G.

    1985-01-01

    The manned Space Station, as currently designed, contains a baseline thermal management system (TMS) which uses components and subsystems never before employed in manned spacecraft. The basis for the technology used in the TMS design is the result of a long-term TMS Technology Development Plan which was initiated in 1979. Rankin and Marshall (1983) have discussed the history and progress of that plan from its beginnings to early 1983. The present paper is concerned with the status of activities conducted at the NASA Lyndon B. Johnson Space Center (JSC) under this plan since 1983, taking into account also a summary of activities planned for the next several years.

  20. Thermal management technology for hydrogen storage: Fullerene option

    SciTech Connect

    Wang, J.C.; Chen, F.C.; Murphy, R.W.

    1996-10-01

    Fullerenes are selected as the first option for investigating advanced thermal management technologies for hydrogen storage because of their potentially high volumetric and gravimetric densities. Experimental results indicate that about 6 wt% of hydrogen (corresponding to C{sub 60}H{sub 48}) can be added to and taken out of fullerenes. A model assuming thermally activated hydrogenation and dehydrogenation processes was developed to explain the experimental findings. The activation energies were estimated to be 100 and 160 kJ/mole (1.0 and 1.6 eV/H{sub 2}) for the hydrogenation and dehydrogenation processes, respectively. The difference is interpreted as the heat released during hydrogenation. There are indications that the activation energies and the heat of hydrogenation can be modified by the use of catalysts. Preliminary hydrogen storage simulations for a conceptually simple device were performed. A 1-m long hollow metal cylinder with an inner diameter of 0.02 m was assumed to be filled with fullerene powders. The results indicate that the thermal diffusivity of the fullerenes controls the hydrogenation and dehydrogenation rates. The rates can be significantly modified by changing the thermal diffusivity of the material inside the cylinder, e.g., by incorporating a metal mesh. Results from the simulation suggest that thermal management is essential for efficient hydrogen storage devices using fullerenes. While the preliminary models developed in this study explain some of the observation, more controlled experiments, rigorous model development, and physical property determinations are needed for the development of practical hydrogen storage devices. The use of catalysts to optimize the hydrogen storage characteristics of fullerenes also needs to be pursued. Future cooperative work between Oak Ridge National Laboratory (ORNL) and Material & Electrochemical Research Corporation (MER) is planned to address these needs.

  1. Thermal surveillance of active volcanoes

    NASA Technical Reports Server (NTRS)

    Friedman, J. D. (Principal Investigator)

    1973-01-01

    The author has identified the following significant results. There are three significant scientific results of the discovery of 48 pinpoint anomalies on the upper flanks of Mt. Rainier: (1) Many of these points may actually be the location of fumarolic vapor emission or warm ground considerably below the summit crater. (2) Discovery of these small anomalies required specific V/H scanner settings for precise elevation on Mt. Rainier's flank, to avoid smearing the anomalies to the point of nonrecognition. Several past missions flown to map the thermal anomalies of the summit area did not/detect the flank anomalies. (3) This illustrates the value of the aerial IR scanner as a geophysical tool suited to specific problem-oriented missions, in contrast to its more general value in a regional or reconnaissance anomaly-mapping role.

  2. Internally drained condenser for spacecraft thermal management

    NASA Technical Reports Server (NTRS)

    Valenzuela, Javier A.; Drew, Brian C.

    1989-01-01

    This paper presents the results obtained to date in a program to develop a high heat flux condenser for use in two-phase spacecraft thermal management loops. The objective is to obtain a several fold increase in condensation heat transfer coefficient over those which can be achieved with shear-controlled or capillary-wick condensers. The internally drained condenser relies on shaped fins to develop a capillary pressure gradient over the surface of the fins and drive the condensate toward narrow drainage grooves separating the fins. The condensate then flows through a drainage network embedded in the condenser walls. Heat transfer coefficients of up to 8 W/sq cm C were measured in steam, providing a heat transfer enhancement ratio greater than a factor of 8. In the paper the proof-of-concept experiments are described and simplified models to predict the performance of the internally drained condenser are presented.

  3. Aerospatiale industrial thermal plasma activities

    NASA Astrophysics Data System (ADS)

    Labrot, Maxime

    Details of nontransferred arc torches, plasma systems in industrial use and operational plasma applications are listed. A plasma application on a foundry cupola is detailed. The setting up of a plasma system is described. Research and development activities are summarized.

  4. Advanced Active Thermal Control Systems Architecture Study

    NASA Technical Reports Server (NTRS)

    Hanford, Anthony J.; Ewert, Michael K.

    1996-01-01

    The Johnson Space Center (JSC) initiated a dynamic study to determine possible improvements available through advanced technologies (not used on previous or current human vehicles), identify promising development initiatives for advanced active thermal control systems (ATCS's), and help prioritize funding and personnel distribution among many research projects by providing a common basis to compare several diverse technologies. Some technologies included were two-phase thermal control systems, light-weight radiators, phase-change thermal storage, rotary fluid coupler, and heat pumps. JSC designed the study to estimate potential benefits from these various proposed and under-development thermal control technologies for five possible human missions early in the next century. The study compared all the technologies to a baseline mission using mass as a basis. Each baseline mission assumed an internal thermal control system; an external thermal control system; and aluminum, flow-through radiators. Solar vapor compression heat pumps and light-weight radiators showed the greatest promise as general advanced thermal technologies which can be applied across a range of missions. This initial study identified several other promising ATCS technologies which offer mass savings and other savings compared to traditional thermal control systems. Because the study format compares various architectures with a commonly defined baseline, it is versatile and expandable, and is expected to be updated as needed.

  5. Thermally activated TRPV3 channels.

    PubMed

    Luo, Jialie; Hu, Hongzhen

    2014-01-01

    TRPV3 is a temperature-sensitive transient receptor potential (TRP) ion channel. The TRPV3 protein functions as a Ca(2+)-permeable nonselective cation channel with six transmembrane domains forming a tetrameric complex. TRPV3 is known to be activated by warm temperatures, synthetic small-molecule chemicals, and natural compounds from plants. Its function is regulated by a variety of physiological factors including extracellular divalent cations and acidic pH, intracellular adenosine triphosphate, membrane voltage, and arachidonic acid. TRPV3 shows a broad expression pattern in both neuronal and non-neuronal tissues including epidermal keratinocytes, epithelial cells in the gut, endothelial cells in blood vessels, and neurons in dorsal root ganglia and CNS. TRPV3 null mice exhibit abnormal hair morphogenesis and compromised skin barrier function. Recent advances suggest that TRPV3 may play critical roles in inflammatory skin disorders, itch, and pain sensation. Thus, identification of selective TRPV3 activators and inhibitors could potentially lead to beneficial pharmacological interventions in several diseases. The intent of this review is to summarize our current knowledge of the tissue expression, structure, function, and mechanisms of activation of TRPV3. PMID:25366242

  6. Intelligent Engine Systems: Thermal Management and Advanced Cooling

    NASA Technical Reports Server (NTRS)

    Bergholz, Robert

    2008-01-01

    The objective of the Advanced Turbine Cooling and Thermal Management program is to develop intelligent control and distribution methods for turbine cooling, while achieving a reduction in total cooling flow and assuring acceptable turbine component safety and reliability. The program also will develop embedded sensor technologies and cooling system models for real-time engine diagnostics and health management. Both active and passive control strategies will be investigated that include the capability of intelligent modulation of flow quantities, pressures, and temperatures both within the supply system and at the turbine component level. Thermal management system concepts were studied, with a goal of reducing HPT blade cooling air supply temperature. An assessment will be made of the use of this air by the active clearance control system as well. Turbine component cooling designs incorporating advanced, high-effectiveness cooling features, will be evaluated. Turbine cooling flow control concepts will be studied at the cooling system level and the component level. Specific cooling features or sub-elements of an advanced HPT blade cooling design will be downselected for core fabrication and casting demonstrations.

  7. Hybrid energy harvesting using active thermal backplane

    NASA Astrophysics Data System (ADS)

    Kim, Hyun-Wook; Lee, Dong-Gun

    2016-04-01

    In this study, we demonstrate the concept of a new hybrid energy harvesting system by combing solar cells with magneto-thermoelectric generator (MTG, i.e., thermal energy harvesting). The silicon solar cell can easily reach high temperature under normal operating conditions. Thus the heated solar cell becomes rapidly less efficient as the temperature of solar cell rises. To increase the efficiency of the solar cell, air or water-based cooling system is used. To surpass conventional cooling devices requiring additional power as well as large working space for air/water collectors, we develop a new technology of pairing an active thermal backplane (ATB) to solar cell. The ATB design is based on MTG technology utilizing the physics of the 2nd order phase transition of active ferromagnetic materials. The MTG is cost-effective conversion of thermal energy to electrical energy and is fundamentally different from Seebeck TEG devices. The ATB (MTG) is in addition to being an energy conversion system, a very good conveyor of heat through both conduction and convection. Therefore, the ATB can provide dual-mode for the proposed hybrid energy harvesting. One is active convective and conductive cooling for heated solar cell. Another is active thermal energy harvesting from heat of solar cell. These novel hybrid energy harvesting device have potentially simultaneous energy conversion capability of solar and thermal energy into electricity. The results presented can be used for better understanding of hybrid energy harvesting system that can be integrated into commercial applications.

  8. Active wireless temperature sensors for aerospace thermal protection systems

    NASA Astrophysics Data System (ADS)

    Milos, Frank S.; Karunaratne, K. S. G.

    2003-07-01

    Vehicle system health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles in order to reduce life-cycle costs, to increase safety margins, and to improve mission reliability. NASA Ames is leading the effort to advance inspection and health management technologies for thermal protection systems. This paper summarizes a joint effort by NASA Ames and Korteks to develop active "wireless" sensors that can be embedded in the thermal protection system to monitor subsurface temperature histories. These devices are thermocouples integrated with radio-frequency identification circuits to enable non-contact communication of temperature data through aerospace thermal protection materials. Two generations of prototype sensors are discussed. The advanced prototype collects data from three type-k thermocouples attached to a 25-mm square integrated circuit and can communicate through 7 to 10 cm thickness of thermal protection materials.

  9. Maximizing Thermal Efficiency and Optimizing Energy Management (Fact Sheet)

    SciTech Connect

    Not Available

    2012-03-01

    Researchers at the Thermal Test Facility (TTF) on the campus of the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) in Golden, Colorado, are addressing maximizing thermal efficiency and optimizing energy management through analysis of efficient heating, ventilating, and air conditioning (HVAC) strategies, automated home energy management (AHEM), and energy storage systems.

  10. Electric Motor Thermal Management R&D; NREL (National Renewable Energy Laboratory)

    SciTech Connect

    Bennion, Kevin

    2015-06-09

    Thermal constraints place significant limitations on how electric motors ultimately perform. Without the ability to remove heat, the motor cannot operate without sacrificing performance, efficiency, and reliability. Finite element analysis and computational fluid dynamics modeling approaches are being increasingly utilized in the design and analysis of electric motors. As the models become more sophisticated, it is important to have detailed and accurate knowledge of both the passive thermal performance and the active cooling performance. In this work, we provide an overview of research characterizing both passive and active thermal elements related to electric motor thermal management. To better characterize the passive thermal performance, work is being performed to measure motor material thermal properties and thermal contact resistances. The active cooling performance of automatic transmission fluid (ATF) jets is also being measured to better understand the heat transfer coefficients of ATF impinging on motor copper windings.

  11. Thermal Management Using Pulsating Jet Cooling Technology

    NASA Astrophysics Data System (ADS)

    Alimohammadi, S.; Dinneen, P.; Persoons, T.; Murray, D. B.

    2014-07-01

    The existing methods of heat removal from compact electronic devises are known to be deficient as the evolving technology demands more power density and accordingly better cooling techniques. Impinging jets can be used as a satisfactory method for thermal management of electronic devices with limited space and volume. Pulsating flows can produce an additional enhancement in heat transfer rate compared to steady flows. This article is part of a comprehensive experimental and numerical study performed on pulsating jet cooling technology. The experimental approach explores heat transfer performance of a pulsating air jet impinging onto a flat surface for nozzle-to-surface distances 1 <= H/D <= 6, Reynolds numbers 1,300 <= Re <= 2,800 pulsation frequency 2Hz <= f <= 65Hz, and Strouhal number 0.0012 <= Sr = fD/Um <= 0.084. The time-resolved velocity at the nozzle exit is measured to quantify the turbulence intensity profile. The numerical methodology is firstly validated using the experimental local Nusselt number distribution for the steady jet with the same geometry and boundary conditions. For a time-averaged Reynolds number of 6,000, the heat transfer enhancement using the pulsating jet for 9Hz <= f <= 55Hz and 0.017 <= Sr <= 0.102 and 1 <= H/D <= 6 are calculated. For the same range of Sr number, the numerical and experimental methods show consistent results.

  12. Thermal Management Coating As Thermal Protection System for Space Transportation System

    NASA Technical Reports Server (NTRS)

    Kaul, Raj; Stuckey, C. Irvin

    2003-01-01

    This paper presents viewgraphs on the development of a non-ablative thermal management coating used as the thermal protection system material for space shuttle rocket boosters and other launch vehicles. The topics include: 1) Coating Study; 2) Aerothermal Testing; 3) Preconditioning Environments; 4) Test Observations; 5) Lightning Strike Test Panel; 6) Test Panel After Impact Testing; 7) Thermal Testing; and 8) Mechanical Testing.

  13. Vertical integration of thermally activated heat pumps

    SciTech Connect

    Chen, F.C.

    1985-01-01

    Many thermally activated heat pump systems are being developed along technology lines, such as, engine-driven and absorption heat pumps. Their thermal performances are temperature dependent. Based on the temperature-dependent behavior of heat pump cycle performance and the energy cascading idea, the concept of vertically integrating various thermally activated heat pump technologies to maximize resources utilization is explored. Based on a preliminary analysis, it is found that integrating a desiccant dehumidification subsystem to an engine-driven heat pump could improve its cooling performance by 36% and integrating an ejector to it could improve its cooling performance by 20%. The added advantage of an ejector-coupled engine-driven heat pump is its system simplicity which should result in equipment cost savings.

  14. Spacecraft active thermal control technology status

    NASA Technical Reports Server (NTRS)

    Ellis, W. E.

    1978-01-01

    Four advanced space radiator concepts that were pursued in an integrated effort to develop multi-mission-use and low cost heat rejection systems which can overcome the limitations of current radiator systems are briefly discussed and described. Also, in order to establish a firm background to compare the advanced space radiator concepts, the Orbiter active thermal control system is also briefly described.

  15. Geothermal reservoir characterization through active thermal testing

    NASA Astrophysics Data System (ADS)

    Jung, Martin; Klepikova, Maria; Jalali, Mohammadreza; Fisch, Hansruedi; Loew, Simon; Amann, Florian

    2016-04-01

    Development and deployment of Enhanced Geothermal Systems (EGS) as renewable energy resources are part of the Swiss Energy Strategy 2050. To pioneer further EGS projects in Switzerland, a decameter-scale in-situ hydraulic stimulation and circulation (ISC) experiment has been launched at the Grimsel Test Site (GTS). The experiments are hosted in a low fracture density volume of the Grimsel granodiorite, similar to those expected at the potential enhanced geothermal system sites in the deep basement rocks of Northern Switzerland. One of the key goals of this multi-disciplinary experiment is to provide a pre- and post-stimulation characterization of the hydraulic and thermal properties of the stimulated fracture network with high resolution and to determine natural structures controlling the fluid flow and heat transport. Active thermal tests including thermal dilution tests and heat tracer tests allow for investigation of groundwater fluid flow and heat transport. Moreover, the spatial and temporal integrity of distributed temperature sensing (DTS) monitoring upgrades the potential and applicability of thermal tests in boreholes (e.g. Read et al., 2013). Here, we present active thermal test results and discuss the advantages and limitations of this method compared to classical approaches (hydraulic packer tests, solute tracer tests, flowing fluid electrical conductivity logging). The experimental tests were conducted in two boreholes intersected by a few low to moderately transmissive fault zones (fracture transmissivity of about 1E-9 m2/s - 1E-7 m2/s). Our preliminary results show that even in low-permeable environments active thermal testing may provide valuable insights into groundwater and heat transport pathways. Read T., O. Bour, V. Bense, T. Le Borgne, P. Goderniaux, M.V. Klepikova, R. Hochreutener, N. Lavenant, and V. Boschero (2013), Characterizing groundwater flow and heat transport in fractured rock using Fiber-Optic Distributed Temperature Sensing

  16. Thermally Activated Martensite: Its Relationship to Non-Thermally Activated (Athermal) Martensite

    SciTech Connect

    Laughlin, D E; Jones, N J; Schwartz, A J; Massalski, T B

    2008-10-21

    The classification of martensitic displacive transformations into athermal, isothermal or anisothermal is discussed. Athermal does not mean 'no temperature dependence' as is often thought, but is best considered to be short for the notion of no thermal activation. Processes with no thermal activation do not depend on time, as there is no need to wait for sufficient statistical fluctuations in some specific order parameter to overcome an activation barrier to initiate the process. Clearly, this kind of process contrasts with those that are thermally activated. In the literature, thermally activated martensites are usually termed isothermal martensites, suggesting a constant temperature. Actually such martensites also typically occur with continuous cooling. The important distinctive feature of these martensites is that they are thermally activated and hence are distinguishable in principle from athermal martensites. A third type of process, anisothermal, has been introduced to account for those transformations which are thought to be thermally activated but which occur on continuous cooling. They may occur so rapidly that they do not appear to have an incubation time, and hence could be mistakenly called an athermal transformation. These designations will be reviewed and discussed in terms of activation energies and kinetic processes of the various martensitic transformations.

  17. Environmental management activities

    SciTech Connect

    1997-07-01

    The Office of Environmental Management (EM) has been delegated the responsibility for the Department of Energy`s (DOE`s) cleanup of the nuclear weapons complex. The nature and magnitude of the waste management and environmental remediation problem requires the identification of technologies and scientific expertise from domestic and foreign sources. Within the United States, operational DOE facilities, as well as the decontamination and decommissioning of inactive facilities, have produced significant amounts of radioactive, hazardous, and mixed wastes. In order to ensure worker safety and the protection of the public, DOE must: (1) assess, remediate, and monitor sites and facilities; (2) store, treat, and dispose of wastes from past and current operations; and (3) develop and implement innovative technologies for environmental restoration and waste management. The EM directive necessitates looking beyond domestic capabilities to technological solutions found outside US borders. Following the collapse of the Soviet regime, formerly restricted elite Soviet scientific expertise became available to the West. EM has established a cooperative technology development program with Russian scientific institutes that meets domestic cleanup objectives by: (1) identifying and accessing Russian EM-related technologies, thereby leveraging investments and providing cost-savings; (2) improving access to technical information, scientific expertise, and technologies applicable to EM needs; and (3) increasing US private sector opportunities in Russian in EM-related areas.

  18. Cryogenic Fluid Management Technology Development for Nuclear Thermal Propulsion

    NASA Technical Reports Server (NTRS)

    Taylor, B. D.; Caffrey, J.; Hedayat, A.; Stephens, J.; Polsgrove, R.

    2015-01-01

    Cryogenic fluid management technology is critical to the success of future nuclear thermal propulsion powered vehicles and long duration missions. This paper discusses current capabilities in key technologies and their development path. The thermal environment, complicated from the radiation escaping a reactor of a nuclear thermal propulsion system, is examined and analysis presented. The technology development path required for maintaining cryogenic propellants in this environment is reviewed. This paper is intended to encourage and bring attention to the cryogenic fluid management technologies needed to enable nuclear thermal propulsion powered deep space missions.

  19. Advanced Fuel Cell System Thermal Management for NASA Exploration Missions

    NASA Technical Reports Server (NTRS)

    Burke, Kenneth A.

    2009-01-01

    The NASA Glenn Research Center is developing advanced passive thermal management technology to reduce the mass and improve the reliability of space fuel cell systems for the NASA exploration program. An analysis of a state-of-the-art fuel cell cooling systems was done to benchmark the portion of a fuel cell system s mass that is dedicated to thermal management. Additional analysis was done to determine the key performance targets of the advanced passive thermal management technology that would substantially reduce fuel cell system mass.

  20. Lunar base thermal management/power system analysis and design

    NASA Technical Reports Server (NTRS)

    Mcghee, Jerry R.

    1992-01-01

    A compilation of several lunar surface thermal management and power system studies completed under contract and IR&D is presented. The work includes analysis and preliminary design of all major components of an integrated thermal management system, including loads determination, active internal acquisition and transport equipment, external transport systems (active and passive), passive insulation, solar shielding, and a range of lunar surface radiator concepts. Several computer codes were utilized in support of this study, including RADSIM to calculate radiation exchange factors and view factors, RADIATOR (developed in-house) for heat rejection system sizing and performance analysis over a lunar day, SURPWER for power system sizing, and CRYSTORE for cryogenic system performance predictions. Although much of the work was performed in support of lunar rover studies, any or all of the results can be applied to a range of surface applications. Output data include thermal loads summaries, subsystem performance data, mass, and volume estimates (where applicable), integrated and worst-case lunar day radiator size/mass and effective sink temperatures for several concepts (shielded and unshielded), and external transport system performance estimates for both single and two-phase (heat pumped) transport loops. Several advanced radiator concepts are presented, along with brief assessments of possible system benefits and potential drawbacks. System point designs are presented for several cases, executed in support of the contract and IR&D studies, although the parametric nature of the analysis is stressed to illustrate applicability of the analysis procedure to a wide variety of lunar surface systems. The reference configuration(s) derived from the various studies will be presented along with supporting criteria. A preliminary design will also be presented for the reference basing scenario, including qualitative data regarding TPS concerns and issues.

  1. Active Wireless Temperature Sensors for Aerospace Thermal Protection Systems

    NASA Technical Reports Server (NTRS)

    Milos, Frank S.; Karunaratne, K.; Arnold, Jim (Technical Monitor)

    2002-01-01

    Health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles in order to reduce life-cycle costs, to increase safety margins, and to improve mission reliability. NASA Ames is leading the effort to advance inspection and health management technologies for thermal protection systems. This paper summarizes a joint project between NASA Ames and Korteks to develop active wireless sensors that can be embedded in the thermal protection system to monitor sub-surface temperature histories. These devices are thermocouples integrated with radio-frequency identification circuitry to enable acquisition and non-contact communication of temperature data through aerospace thermal protection materials. Two generations of prototype sensors are discussed. The advanced prototype collects data from three type-k thermocouples attached to a 2.54-cm square integrated circuit.

  2. Environmental Management vitrification activities

    SciTech Connect

    Krumrine, P.H.

    1996-05-01

    Both the Mixed Waste and Landfill Stabilization Focus Areas as part of the Office of Technology Development efforts within the Department of Energy`s (DOE) Environmental Management (EM) Division have been developing various vitrification technologies as a treatment approach for the large quantities of transuranic (TRU), TRU mixed and Mixed Low Level Wastes that are stored in either landfills or above ground storage facilities. The technologies being developed include joule heated, plasma torch, plasma arc, induction, microwave, combustion, molten metal, and in situ methods. There are related efforts going into development glass, ceramic, and slag waste form windows of opportunity for the diverse quantities of heterogeneous wastes needing treatment. These studies look at both processing parameters, and long term performance parameters as a function of composition to assure that developed technologies have the right chemistry for success.

  3. Collective behavior of thermally active colloids.

    PubMed

    Golestanian, Ramin

    2012-01-20

    Colloids with patchy metal coating under laser irradiation could act as local heat sources and generate temperature gradients that could induce self-propulsion and interactions between them. The collective behavior of a dilute solution of such thermally active particles is studied using a stochastic formulation. It is found that when the Soret coefficient is positive, the system could be described in a stationary state by the nonlinear Poisson-Boltzmann equation and could adopt density profiles with significant depletion in the middle region when confined. For colloids with a negative Soret coefficient, the system can be described as a dissipative equivalent of a gravitational system. It is shown that in this case the thermally active colloidal solution could undergo an instability at a critical laser intensity, which has similarities to a supernova explosion. PMID:22400792

  4. Collective Behavior of Thermally Active Colloids

    NASA Astrophysics Data System (ADS)

    Golestanian, Ramin

    2012-01-01

    Colloids with patchy metal coating under laser irradiation could act as local heat sources and generate temperature gradients that could induce self-propulsion and interactions between them. The collective behavior of a dilute solution of such thermally active particles is studied using a stochastic formulation. It is found that when the Soret coefficient is positive, the system could be described in a stationary state by the nonlinear Poisson-Boltzmann equation and could adopt density profiles with significant depletion in the middle region when confined. For colloids with a negative Soret coefficient, the system can be described as a dissipative equivalent of a gravitational system. It is shown that in this case the thermally active colloidal solution could undergo an instability at a critical laser intensity, which has similarities to a supernova explosion.

  5. Boron nitride nanomaterials for thermal management applications.

    PubMed

    Meziani, Mohammed J; Song, Wei-Li; Wang, Ping; Lu, Fushen; Hou, Zhiling; Anderson, Ankoma; Maimaiti, Halidan; Sun, Ya-Ping

    2015-05-18

    Hexagonal boron nitride nanosheets (BNNs) are analogous to their two-dimensional carbon counterparts in many materials properties, in particular, ultrahigh thermal conductivity, but also offer some unique attributes, including being electrically insulating, high thermal stability, chemical and oxidation resistance, low color, and high mechanical strength. Significant recent advances in the production of BNNs, understanding of their properties, and the development of polymeric nanocomposites with BNNs for thermally conductive yet electrically insulating materials and systems are highlighted herein. Major opportunities and challenges for further studies in this rapidly advancing field are also discussed. PMID:25652360

  6. Report on Toyota Prius Motor Thermal Management

    SciTech Connect

    Hsu, J.S.

    2005-02-11

    peak-torque (400-Nm) region, the efficiency goes down to the 40-50% range, and the power factor is nearly 100%. The efficiency is not a major concern at the high-torque region. The water-ethylene-glycol heat exchanger attached to the motor is small. During continuous operation, it dissipates about 76% of the total motor heat loss with 35 C coolant. The heat exchanger is less effective when the coolant temperature increases. With 75 C coolant, the heat exchanger dissipates about 38% of the motor heat. When the coolant temperature is 105 C, the heat exchanger not only stops cooling the motor but also adds heat to the large motor housing that acts as an air-cooled heat sink. From start to the base speed, 400 Nms of torque can be produced by the Prius motor with a reasonably low stator current. However, the permissible running time of the motor depends on the load drawn from the motor and the coolant temperature. In the Toyota Prius hybrid configuration, if the motor gets too hot and cannot keep running, the load can be shifted back to the engine. The motor acts to improve the system efficiency without being overly designed. A detailed thermal model was developed to help predict the temperature levels in key motor components. The model was calibrated and compared with the experimentally measured temperatures. Very good agreement was obtained between model and experiment. This model can now be used to predict the temperature of key motor components at a variety of operating conditions and to evaluate the thermal characteristics of new motor designs. It should be pointed out that a fuel-cell motor does not have an engine to fall back on to provide the needed wheel power. Therefore, the design philosophy of a fuel-cell motor is very different from that of a hybrid Prius motor. Further thermal management studies in the high-speed region of the Prius motor, fed by its inverter, are planned.

  7. Demonstration of Passive Fuel Cell Thermal Management Technology

    NASA Technical Reports Server (NTRS)

    Burke, Kenneth A.; Jakupca, Ian; Colozza, Anthony; Wynne, Robert; Miller, Michael; Meyer, Al; Smith, William

    2012-01-01

    The NASA Glenn Research Center is developing advanced passive thermal management technology to reduce the mass and improve the reliability of space fuel cell systems for the NASA Exploration program. The passive thermal management system relies on heat conduction within highly thermally conductive cooling plates to move the heat from the central portion of the cell stack out to the edges of the fuel cell stack. Using the passive approach eliminates the need for a coolant pump and other cooling loop components within the fuel cell system which reduces mass and improves overall system reliability. Previous development demonstrated the performance of suitable highly thermally conductive cooling plates and integrated heat exchanger technology to collect the heat from the cooling plates (Ref. 1). The next step in the development of this passive thermal approach was the demonstration of the control of the heat removal process and the demonstration of the passive thermal control technology in actual fuel cell stacks. Tests were run with a simulated fuel cell stack passive thermal management system outfitted with passive cooling plates, an integrated heat exchanger and two types of cooling flow control valves. The tests were run to demonstrate the controllability of the passive thermal control approach. Finally, successful demonstrations of passive thermal control technology were conducted with fuel cell stacks from two fuel cell stack vendors.

  8. Thermal Stability of Chelated Indium Activable Tracers

    SciTech Connect

    Chrysikopoulos, Costas; Kruger, Paul

    1986-01-21

    The thermal stability of indium tracer chelated with organic ligands ethylenediaminetetraacetic acid (EDTA) and nitrilotriacetic acid (NTA) was measured for reservoir temperatures of 150, 200, and 240 C. Measurements of the soluble indium concentration was made as a function of time by neutron activation analysis. From the data, approximate thermal decomposition rates were estimated. At 150 C, both chelated tracers were stable over the experimental period of 20 days. At 200 C, the InEDTA concentration remained constant for 16 days, after which the thermal decomposition occurred at a measured rate constant of k = 0.09 d{sup -1}. The thermal decomposition of InNTA at 200 C showed a first order reaction with a measured rate constant of k = 0.16 d{sup -1}. At 240 C, both indium chelated tracers showed rapid decomposition with rate constants greater than 1.8 d{sup -1}. The data indicate that for geothermal reservoir with temperatures up to about 200 C, indium chelated tracers can be used effectively for transit times of at least 20 days. These experiments were run without reservoir rock media, and do not account for concomitant loss of indium tracer by adsorption processes.

  9. Thermal analysis and management of lithium-titanate batteries

    NASA Astrophysics Data System (ADS)

    Giuliano, Michael R.; Advani, Suresh G.; Prasad, Ajay K.

    2011-08-01

    Battery electric vehicles and hybrid electric vehicles demand batteries that can store large amounts of energy in addition to accommodating large charge and discharge currents without compromising battery life. Lithium-titanate batteries have recently become an attractive option for this application. High current thresholds allow these cells to be charged quickly as well as supply the power needed to drive such vehicles. These large currents generate substantial amounts of waste heat due to loss mechanisms arising from the cell's internal chemistry and ohmic resistance. During normal vehicle operation, an active cooling system must be implemented to maintain a safe cell temperature and improve battery performance and life. This paper outlines a method to conduct thermal analysis of lithium-titanate cells under laboratory conditions. Thermochromic liquid crystals were implemented to instantaneously measure the entire surface temperature field of the cell. The resulting temperature measurements were used to evaluate the effectiveness of an active cooling system developed and tested in our laboratory for the thermal management of lithium-titanate cells.

  10. Intelligent Engine Systems: Thermal Management and Advanced Cooling

    NASA Technical Reports Server (NTRS)

    Bergholz, Robert

    2008-01-01

    The objective is to provide turbine-cooling technologies to meet Propulsion 21 goals related to engine fuel burn, emissions, safety, and reliability. Specifically, the GE Aviation (GEA) Advanced Turbine Cooling and Thermal Management program seeks to develop advanced cooling and flow distribution methods for HP turbines, while achieving a substantial reduction in total cooling flow and assuring acceptable turbine component safety and reliability. Enhanced cooling techniques, such as fluidic devices, controlled-vortex cooling, and directed impingement jets, offer the opportunity to incorporate both active and passive schemes. Coolant heat transfer enhancement also can be achieved from advanced designs that incorporate multi-disciplinary optimization of external film and internal cooling passage geometry.

  11. An engineering code to analyze hypersonic thermal management systems

    NASA Technical Reports Server (NTRS)

    Vangriethuysen, Valerie J.; Wallace, Clark E.

    1993-01-01

    Thermal loads on current and future aircraft are increasing and as a result are stressing the energy collection, control, and dissipation capabilities of current thermal management systems and technology. The thermal loads for hypersonic vehicles will be no exception. In fact, with their projected high heat loads and fluxes, hypersonic vehicles are a prime example of systems that will require thermal management systems (TMS) that have been optimized and integrated with the entire vehicle to the maximum extent possible during the initial design stages. This will not only be to meet operational requirements, but also to fulfill weight and performance constraints in order for the vehicle to takeoff and complete its mission successfully. To meet this challenge, the TMS can no longer be two or more entirely independent systems, nor can thermal management be an after thought in the design process, the typical pervasive approach in the past. Instead, a TMS that was integrated throughout the entire vehicle and subsequently optimized will be required. To accomplish this, a method that iteratively optimizes the TMS throughout the vehicle will not only be highly desirable, but advantageous in order to reduce the manhours normally required to conduct the necessary tradeoff studies and comparisons. A thermal management engineering computer code that is under development and being managed at Wright Laboratory, Wright-Patterson AFB, is discussed. The primary goal of the code is to aid in the development of a hypersonic vehicle TMS that has been optimized and integrated on a total vehicle basis.

  12. Thermal Management Tools for Propulsion System Trade Studies and Analysis

    NASA Technical Reports Server (NTRS)

    McCarthy, Kevin; Hodge, Ernie

    2011-01-01

    Energy-related subsystems in modern aircraft are more tightly coupled with less design margin. These subsystems include thermal management subsystems, vehicle electric power generation and distribution, aircraft engines, and flight control. Tighter coupling, lower design margins, and higher system complexity all make preliminary trade studies difficult. A suite of thermal management analysis tools has been developed to facilitate trade studies during preliminary design of air-vehicle propulsion systems. Simulink blocksets (from MathWorks) for developing quasi-steady-state and transient system models of aircraft thermal management systems and related energy systems have been developed. These blocksets extend the Simulink modeling environment in the thermal sciences and aircraft systems disciplines. The blocksets include blocks for modeling aircraft system heat loads, heat exchangers, pumps, reservoirs, fuel tanks, and other components at varying levels of model fidelity. The blocksets have been applied in a first-principles, physics-based modeling and simulation architecture for rapid prototyping of aircraft thermal management and related systems. They have been applied in representative modern aircraft thermal management system studies. The modeling and simulation architecture has also been used to conduct trade studies in a vehicle level model that incorporates coupling effects among the aircraft mission, engine cycle, fuel, and multi-phase heat-transfer materials.

  13. Active thermal isolation for temperature responsive sensors

    NASA Technical Reports Server (NTRS)

    Martinson, Scott D. (Inventor); Gray, David L. (Inventor); Carraway, Debra L. (Inventor); Reda, Daniel C. (Inventor)

    1994-01-01

    The detection of flow transition between laminar and turbulent flow and of shear stress or skin friction of airfoils is important in basic research for validation of airfoil theory and design. These values are conventionally measured using hot film nickel sensors deposited on a polyimide substrate. The substrate electrically insulates the sensor and underlying airfoil but is prevented from thermally isolating the sensor by thickness constraints necessary to avoid flow contamination. Proposed heating of the model surface is difficult to control, requires significant energy expenditures, and may alter the basic flow state of the airfoil. A temperature responsive sensor is located in the airflow over the specified surface of a body and is maintained at a constant temperature. An active thermal isolator is located between this temperature responsive sensor and the specific surface of the body. The total thickness of the isolator and sensor avoid any contamination of the flow. The temperature of this isolator is controlled to reduce conductive heat flow from the temperature responsive sensor to the body. This temperature control includes (1) operating the isolator at the same temperature as the constant temperature of the sensor; and (2) establishing a fixed boundary temperature which is either less than or equal to, or slightly greater than the sensor constant temperature. The present invention accordingly thermally isolates a temperature responsive sensor in an energy efficient, controllable manner while avoiding any contamination of the flow.

  14. Thermally activated conductivity in gapped bilayer graphene

    NASA Astrophysics Data System (ADS)

    Trushin, Maxim

    2012-05-01

    This is a theoretical study of electron transport in gated bilayer graphene —a novel semiconducting material with a tunable band gap. It is shown that the which-layer pseudospin coherence enhances the subgap conductivity and facilitates the thermally activated transport. The mechanism proposed can also lead to the non-monotonic conductivity vs. temperature dependence at a band gap size of the order of 10 meV. The effect can be observed in gapped bilayer graphene sandwiched in boron nitride where the electron-hole puddles and flexural phonons are strongly suppressed.

  15. Thermally activated helicity reversals of skyrmions

    NASA Astrophysics Data System (ADS)

    Yu, X. Z.; Shibata, K.; Koshibae, W.; Tokunaga, Y.; Kaneko, Y.; Nagai, T.; Kimoto, K.; Taguchi, Y.; Nagaosa, N.; Tokura, Y.

    2016-04-01

    Magnetic bubbles with winding number S =1 are topologically equivalent to skyrmions. Here we report the discovery of helicity (in-plane magnetization-swirling direction) reversal of skyrmions, while keeping their hexagonal lattice form, at above room temperature in a thin hexaferrite magnet. We have observed that the frequency of helicity reversals dramatically increases with temperature in a thermally activated manner, revealing that the generation energy of a kink-soliton pair for switching helicity on a skyrmion rapidly decreases towards the magnetic transition temperature.

  16. Active thermal isolation for temperature responsive sensors

    NASA Technical Reports Server (NTRS)

    Martinson, Scott D. (Inventor); Gray, David L. (Inventor); Carraway, Debra L. (Inventor); Reda, Daniel C. (Inventor)

    1994-01-01

    A temperature responsive sensor is located in the airflow over the specified surface of a body and is maintained at a constant temperature. An active thermal isolator is located between this temperature responsive sensor and the specified surface of the body. The temperature of this isolator is controlled to reduce conductive heat flow from the temperature responsive sensor to the body. This temperature control includes: (1) operating the isolator at the same temperature as the constant temperature of the sensor and (2) establishing a fixed boundary temperature which is either less than or equal to or slightly greater than the sensor constant temperature.

  17. High-power thermal management issues in space-based systems

    NASA Astrophysics Data System (ADS)

    Ponnappan, Rengasamy; Donovan, Brian; Chow, Louis

    2002-01-01

    There are several initiatives currently active or planned to enable future military directed energy, surveillance and communication missions. These missions require a very high level of electric power and sophisticated power conditioning systems. In almost all of these systems, there are unique thermal management requirements from electronics and payload operational considerations such as isothermality, high-heat flux, low-pressure drop, efficient fluid management and high heat transfer coefficient. The other space related requirements and issues affecting thermal management are microgravity, scalability based on weight, volume, reliability, safety, and cost considerations. In meeting these requirements for space systems, the thermal designer is faced with many technical challenges and issues. This paper describes some of these key issues and presents the need for initiating advanced developments in certain areas such as spray cooling, two-phase pumped loop and heat pump systems. In addition, it is emphasized to focus attention on extended microgravity effects of thermal systems. .

  18. HCCI engine control by thermal management

    SciTech Connect

    Martinez-Frias, J; Aceves, S M; Flowers, D; Smith, J R; Dibble, R

    2000-05-11

    This work investigates a control system for HCCI engines, where thermal energy from exhaust gas recirculation (EGR) and compression work in the supercharger are either recycled or rejected as needed. HCCI engine operation is analyzed with a detailed chemical kinetics code, HCT (Hydrodynamics, Chemistry and Transport), that has been extensively modified for application to engines. HCT is linked to an optimizer that determines the operating conditions that result in maximum brake thermal efficiency, while meeting the restrictions of low NO{sub x} and peak cylinder pressure. The results show the values of the operating conditions that yield optimum efficiency as a function of torque and RPM. For zero torque (idle), the optimizer determines operating conditions that result in minimum fuel consumption. The optimizer is also used for determining the maximum torque that can be obtained within the operating restrictions of NO{sub x} and peak cylinder pressure. The results show that a thermally controlled HCCI engine can successfully operate over a wide range of conditions at high efficiency and low emissions.

  19. Thermal Performance of a Cryogenic Fluid Management Cubesat Mission

    NASA Technical Reports Server (NTRS)

    Berg, J. J.; Oliveira, J. M.; Congiardo, J. F.; Walls, L. K.; Putman, P. T.; Haberbusch, M. S.

    2013-01-01

    Development for an in-space demonstration of a CubeS at as a Cryogenic Fluid Management (CFM) test bed is currently underway. The favorable economics of CubeSats make them appealing for technology development activity. While their size limits testing to smaller scales, many of the regimes relevant to CFM can still be achieved. The first demo flight of this concept, CryoCube®-1, will focus on oxygen liquefaction and low-gravity level sensing using Reduced Gravity CryoTracker®. An extensive thermal modeling effort has been underway to both demonstrate concept feasibility and drive the prototype design. The satellite will utilize both a sun- and earth-shield to passively cool its experimental tank below 115 K. An on-board gas generator will create high pressure gaseous oxygen, which will be throttled into a bottle in the experimental node and condensed. The resulting liquid will be used to perform various experiments related to level sensing. Modeling efforts have focused on the spacecraft thermal performance and its effects on condensation in the experimental node. Parametric analyses for both optimal and suboptimal conditions have been considered and are presented herein.

  20. Thermal management of VECSELs by front surface direct liquid cooling

    NASA Astrophysics Data System (ADS)

    Smyth, Conor J. C.; Mirkhanov, Shamil; Quarterman, Adrian H.; Wilcox, Keith G.

    2016-03-01

    Efficient thermal management is vital for VECSELs, affecting the output power and several aspects of performance of the device. Presently there exist two distinct methods of effective thermal management which both possess their merits and disadvantages. Substrate removal of the VECSEL gain chip has proved a successful method in devices emitting at a wavelength near 1μm. However for other wavelengths the substrate removal technique has proved less effective primarily due to the thermal impedance of the distributed Bragg reflectors. The second method of thermal management involves the use of crystalline heat spreaders bonded to the gain chip surface. Although this is an effective thermal management scheme, the disadvantages are additional loss and the etalon effect that filters the gain spectrum, making mode locking more difficult and normally resulting in multiple peaks in the spectrum. There are considerable disadvantages associated with both methods attributed to heatspreader cost and sample processing. It is for these reasons that a proposed alternative, front surface liquid cooling, has been investigated in this project. Direct liquid cooling involves flowing a temperature-controlled liquid over the sample's surface. In this project COMSOL was used to model surface liquid cooling of a VECSEL sample in order to investigate and compare its potential thermal management with current standard thermal management techniques. Based on modelling, experiments were carried out in order to evaluate the performance of the technique. While modelling suggests that this is potentially a mid-performance low cost alternative to existing techniques, experimental measurements to date do not reflect the performance predicted from modelling.

  1. Ocean Thermal Energy Conversion Program Management Plan

    SciTech Connect

    Combs, R E

    1980-01-01

    The Office of the Associate Laboratory Director for Energy and Environmental Technology has established the OTEC Program Management Office to be responsible for the ANL-assigned tasks of the OTEC Program under DOE's Chicago Operations and Regional Office (DOE/CORO). The ANL OTEC Program Management Plan is essentially a management-by-objective plan. The principal objective of the program is to provide lead technical support to CORO in its capacity as manager of the DOE power-system program. The Argonne OTEC Program is divided into three components: the first deals with development of heat exchangers and other components of OTEC power systems, the second with development of biofouling counter-measures and corrosion-resistant materials for these components in seawater service, and the third with environmental and climatic impacts of OTEC power-system operation. The essential points of the Management Plan are summarized, and the OTEC Program is described. The organization of the OTEC Program at ANL is described including the functions, responsibilities, and authorities of the organizational groupings. The system and policies necessary for the support and control functions within the organization are discussed. These functions cross organizational lines, in that they are common to all of the organization groups. Also included are requirements for internal and external reports.

  2. Quasi 2D Materials: Raman Nanometrology and Thermal Management Applications

    NASA Astrophysics Data System (ADS)

    Shahil, Khan Mohammad Farhan

    Quasi two-dimensional (2D) materials obtained by the "graphene-like" exfoliation attracted tremendous attention. Such materials revealed unique electronic, thermal and optical properties, which can be potentially used in electronics, thermal management and energy conversion. This dissertation research addresses two separate but synergetic problems: (i) preparation and optical characterization of quasi-2D films of the bismuth-telluride (Bi 2Te3) family of materials, which demonstrate both thermoelectric and topological insulator properties; and (ii) investigation of thermal properties of composite materials prepared with graphene and few-layer graphene (FLG). The first part of dissertation reports properties of the exfoliated few-quintuple layers of Bi2Te3, Bi2Se3 and Sb 2Te3. Both non-resonant and resonant Raman scattering spectra have been investigated. It was found that the crystal symmetry breaking in few-quintuple films results in appearance of A1u-symmetry Raman peaks, which are not active in the bulk crystals. The scattering spectra measured under the 633-nm wavelength excitation reveals a number of resonant features, which could be used for analysis of the electronic and phonon processes in these materials. The obtained results help to understand the physical mechanisms of Raman scattering in the few-quintuple-thick films and can be used for nanometrology of topological insulator films on various substrates. The second part of the dissertation is dedicated to investigation of properties of composite materials prepared with graphene and FLG. It was found that the optimized mixture of graphene and multilayer graphene---produced by the high-yield inexpensive liquid-phase-exfoliation technique---can lead to an extremely strong enhancement of the cross-plane thermal conductivity K of the composite. The "laser flash" measurements revealed a record-high enhancement of K by 2300 % in the graphene-based polymer at the filler loading fraction f =10 vol. %. It was

  3. Novel Material Systems and Methodologies for Transient Thermal Management

    NASA Technical Reports Server (NTRS)

    Oliva-Buisson, Yvette J.

    2014-01-01

    Development of multifunctional and thermally switchable systems to address reduced mass and components, and tailored for both structural and transient thermal applications. Active, passive, and novel combinations of the two functional approaches are being developed along two lines of research investigation: switchable systems and transient heat spreading. The approach is to build in thermal functionality to structural elements to lay the foundation for a revolution in the way high energy space systems are designed.

  4. Advances in photonics thermal management and packaging materials

    NASA Astrophysics Data System (ADS)

    Zweben, Carl

    2008-02-01

    Heat dissipation, thermal stresses, and cost are key packaging design issues for virtually all semiconductors, including photonic applications such as diode lasers, light-emitting diodes (LEDs), solid state lighting, photovoltaics, displays, projectors, detectors, sensors and laser weapons. Heat dissipation and thermal stresses affect performance and reliability. Copper, aluminum and conventional polymeric printed circuit boards (PCBs) have high coefficients of thermal expansion, which can cause high thermal stresses. Most traditional low-coefficient-of-thermal-expansion (CTE) materials like tungsten/copper, which date from the mid 20 th century, have thermal conductivities that are no better than those of aluminum alloys, about 200 W/m-K. There are an increasing number of low-CTE materials with thermal conductivities ranging between that of copper (400 W/m-K) and 1700 W/m-K, and many other new low-CTE materials with lower thermal conductivities. An important benefit of low-CTE materials is that they allow use of hard solders. Some advanced materials are low cost. Others have the potential to be low cost in high-volume production. High-thermal-conductivity materials enable higher power levels, potentially reducing the number of required devices. Advanced thermal materials can constrain PCB CTE and greatly increase thermal conductivity. This paper reviews traditional packaging materials and advanced thermal management materials. The latter provide the packaging engineer with a greater range of options than in the past. Topics include properties, status, applications, cost, using advanced materials to fix manufacturing problems, and future directions, including composites reinforced with carbon nanotubes and other thermally conductive materials.

  5. SOFC seal and cell thermal management

    DOEpatents

    Potnis, Shailesh Vijay; Rehg, Timothy Joseph

    2011-05-17

    The solid oxide fuel cell module includes a manifold, a plate, a cathode electrode, a fuel cell and an anode electrode. The manifold includes an air or oxygen inlet in communication with divergent passages above the periphery of the cell which combine to flow the air or oxygen radially or inwardly for reception in the center of the cathode flow field. The latter has interconnects providing circuitous cooling passages in a generally radial outward direction cooling the fuel cell and which interconnects are formed of different thermal conductivity materials for a preferential cooling.

  6. Thermal conductivity tensors of the cladding and active layers of interband cascade lasers

    NASA Astrophysics Data System (ADS)

    Zhou, Chuanle; Cui, Boya; Vurgaftman, I.; Canedy, C. L.; Kim, C. S.; Kim, M.; Bewley, W. W.; Merritt, C. D.; Abell, J.; Meyer, J. R.; Grayson, M.

    2014-12-01

    The cross-plane and in-plane thermal conductivities of the W-active stages and InAs/AlSb superlattice optical cladding layer of an interband cascade laser (ICL) were characterized for temperatures ranging from 15 K to 324 K. The in-plane thermal conductivity of the active layer is somewhat larger than the cross-plane value at temperatures above about 30 K, while the thermal conductivity tensor becomes nearly isotropic at the lowest temperatures studied. These results will improve ICL performance simulations and guide the optimization of thermal management.

  7. Miniature Loop Heat Pipe (MLHP) Thermal Management System

    NASA Technical Reports Server (NTRS)

    Ku, Jentung

    2004-01-01

    The MLHP Thermal Management System consists of a loop heat pipe (LHP) with multiple evaporators and condensers, thermal electrical coolers, and deployable radiators coated with variable emittance coatings (VECs). All components are miniaturized. It retains all the performance characteristics of state-of-the-art LHPs and offers additional advantages to enhance the functionality, versatility, and reliability of the system, including flexible locations of instruments and radiators, a single interface temperature for multiple instruments, cooling the on instruments and warming the off instruments simultaneously, improving. start-up success, maintaining a constant LHP operating temperature over a wide range of instrument powers, effecting automatic thermal switching and thermal diode actions, and reducing supplemental heater powers. It can fully achieve low mass, low power and compactness necessary for future small spacecraft. Potential applications of the MLHP thermal technology for future missions include: 1) Magnetospheric Constellation; 2) Solar Sentinels; 3) Mars Science Laboratory; 4) Mars Scouts; 5) Mars Telecom Orbiter; 6) Space Interferometry Mission; 7) Laser Interferometer Space Antenna; 8) Jupiter Icy Moon Orbiter; 9) Terrestrial Planet Finder; 10) Single Aperture Far-Infrared Observatory, and 11) Exploration Missions. The MLHP Thermal Management System combines the operating features of a variable conductance heat pipe, a thermal switch, a thermal diode, and a state-of-the-art LHP into a single integrated thermal system. It offers many advantages over conventional thermal control techniques, and can be a technology enabler for future space missions. Successful flight validation will bring the benefits of MLHP technology to the small satellite arena and will have cross-cutting applications to both Space Science and Earth Science Enterprises.

  8. Thermal-hydraulics for space power, propulsion, and thermal management system design

    SciTech Connect

    Krotiuk, W.J.

    1990-01-01

    The present volume discusses thermal-hydraulic aspects of current space projects, Space Station thermal management systems, the thermal design of the Space Station Free-Flying Platforms, the SP-100 Space Reactor Power System, advanced multi-MW space nuclear power concepts, chemical and electric propulsion systems, and such aspects of the Space Station two-phase thermal management system as its mechanical pumped loop and its capillary pumped loop's supporting technology. Also discussed are the startup thaw concept for the SP-100 Space Reactor Power System, calculational methods and experimental data for microgravity conditions, an isothermal gas-liquid flow at reduced gravity, low-gravity flow boiling, computations of Space Shuttle high pressure cryogenic turbopump ball bearing two-phase coolant flow, and reduced-gravity condensation.

  9. Thru-life impacts of driver aggression, climate, cabin thermal management, and battery thermal management on battery electric vehicle utility

    NASA Astrophysics Data System (ADS)

    Neubauer, Jeremy; Wood, Eric

    2014-08-01

    Battery electric vehicles (BEVs) offer the potential to reduce both oil imports and greenhouse gas emissions, but have a limited utility that is affected by driver aggression and effects of climate-both directly on battery temperature and indirectly through the loads of cabin and battery thermal management systems. Utility is further affected as the battery wears through life in response to travel patterns, climate, and other factors. In this paper we apply the National Renewable Energy Laboratory's Battery Lifetime Analysis and Simulation Tool for Vehicles (BLAST-V) to examine the sensitivity of BEV utility to driver aggression and climate effects over the life of the vehicle. We find the primary challenge to cold-climate BEV operation to be inefficient cabin heating systems, and to hot-climate BEV operation to be high peak on-road battery temperatures and excessive battery degradation. Active cooling systems appear necessary to manage peak battery temperatures of aggressive, hot-climate drivers, which can then be employed to maximize thru-life vehicle utility.

  10. Manatee response to boating activity in a thermal refuge

    USGS Publications Warehouse

    Buckingham, C.A.; Lefebvre, L.W.; Schaefer, J.M.; Kochman, H.I.

    1999-01-01

    Thermal refuges are important for the endangered Florida manatee (Trichechus manatus latirostris) during winter cold periods in temperate latitudes. However, little research has examined impacts on manatees from human disturbance during these critical periods. We studied the effect of recreational boating activity on manatee use of established sanctuaries in the natural thermal refuge created by warm-water springs in Kings Bay, Crystal River, Florida. We examined the relationship among manatee use of the study area and sanctuaries, temperature, and level of boating activity. Manatees continued to use the Bay regardless of the number of boats present; however, their use of sanctuaries in the southern portion of the Bay increased (P<0.001) as number of boats increased. Temperature, as expected, was inversely related to manatee use of the study area. Human activity patterns were variable, with significantly greater numbers of boats in the study area on weekends (x??=32.7, SE=2.71) than on weekdays (x??=10.7, SE=1.23). We concluded that recreational boating influenced manatee distribution, sanctuaries are important to manatees in Kings Bay, and sanctuaries are an effective management tool to reduce the impact of boating activities on manatees.

  11. Development of Passive Fuel Cell Thermal Management Heat Exchanger

    NASA Technical Reports Server (NTRS)

    Burke, Kenneth A.; Jakupca, Ian J.; Colozza, Anthony J.

    2010-01-01

    The NASA Glenn Research Center is developing advanced passive thermal management technology to reduce the mass and improve the reliability of space fuel cell systems for the NASA Exploration program. The passive thermal management system relies on heat conduction within highly thermally conductive cooling plates to move the heat from the central portion of the cell stack out to the edges of the fuel cell stack. Using the passive approach eliminates the need for a coolant pump and other cooling loop components within the fuel cell system which reduces mass and improves overall system reliability. Previous development demonstrated the performance of suitable highly thermally conductive cooling plates that could conduct the heat, provide a sufficiently uniform temperature heat sink for each cell of the fuel cell stack, and be substantially lighter than the conventional thermal management approach. Tests were run with different materials to evaluate the design approach to a heat exchanger that could interface with the edges of the passive cooling plates. Measurements were made during fuel cell operation to determine the temperature of individual cooling plates and also to determine the temperature uniformity from one cooling plate to another.

  12. Enhancing Thermal Conductivity of Hexagonal Boron Nitride Filled Thermoplastics for Thermal Interface Management

    NASA Astrophysics Data System (ADS)

    Prindl, John

    Hexagonal Boron Nitride has been shown to enhance thermal conductivity in polymer composites more so than conventional ceramic fillers. However, to see a significant increase in thermal conductivity a high loading level of the advanced ceramic is often needed which can have an adverse effect on the mechanical behavior of the composite part. Applications for thermal management using thermal interface materials (TIM) continue to grow with thermoplastic injection molded parts emerging as an area for market growth. There is a growing need for published technical data in this particular area of application. In the current study, the thermal conductivity and mechanical behavior of hexagonal Boron Nitride (hBN) loaded thermoplastic composites is investigated. The main objectives of this work is produce a novel data package which illustrates the effects of hBN, loaded at high concentrations, across several different thermoplastic resins with the ultimate goal being to find a desirable formulation for specific thermal management applications. The desired properties for such applications being high thermal conductivity and high electrical resistivity with a minimal decrease in mechanical properties. Hexagonal BN cooling filler agglomerates were compounded into polypropylene (PP), nylon-6 (PA-6), and thermoplastic elastomer (TPE) via twin-screw extruder at 3 different loading levels. Injection molded samples were produced and characterized to show varying degrees of thermal conductivity and mechanical strength. Results from this research showed that in all cases, the thermal conductivity increased with increasing levels of hBN addition. The largest increases in thermal conductivity were seen in the PA-6 and TPE systems with the possible indication of exceeding the percolation threshold in the TPE system. This is hypothesized to occur due to the preferential migration of hBN to form conduction pathways around the elastomeric domains in the TPE matrix. Though TPE produced

  13. Irrigation system management assisted by thermal imagery and spatial statistics

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Thermal imaging has the potential to assist with many aspects of irrigation management including scheduling water application, detecting leaky irrigation canals, and gauging the overall effectiveness of water distribution networks used in furrow irrigation. Many challenges exist for the use of therm...

  14. A Thermal Management of Electronics Course and Laboratory for Undergraduates

    ERIC Educational Resources Information Center

    Okamoto, Nicole; Hsu, Tai-Ran; Bash, Cullen E.

    2009-01-01

    A novel thermal management of electronics course with an associated laboratory has been developed for mechanical, electrical, and computer engineering students. The lecture topics, term project, computer modeling project, and six associated experiments that were built from scratch are described. Over half of the course lectures as well as all lab…

  15. Power Electronics Thermal Management R&D (Presentation)

    SciTech Connect

    Waye, S.

    2014-11-01

    This project will investigate and develop thermal-management strategies for wide bandgap (WBG)-based power electronics systems. Research will be carried out to deal with thermal aspects at the module- and system-level. Module-level research will focus on die- and substrate-integrated cooling strategies and heat-transfer enhancement technologies. System-level research will focus on thermal-management strategies for the entire power electronics system to enable smart packaging solutions. One challenge with WBG device-based power electronics is that although losses in the form of heat may be lower, the footprint of the components is also likely to be reduced to reduce cost, weight, and volume. Combined with higher operational temperatures, this creates higher heat fluxes which much be removed from a smaller footprint, requiring advanced cooling strategies.

  16. Ultrasonic Activation of Thermally Sensitive Liposomes

    NASA Astrophysics Data System (ADS)

    Mylonopouloua, Eleonora; Arvanitisa, Costas D.; Bazan-Peregrinoa, Miriam; Arora, Manish; Coussios, Constantin C.

    2010-03-01

    Cancerous cells are known to be more vulnerable to mild hyperthermia than healthy cells, which can survive temperatures above 43° C for brief periods of time. Currently in phase III clinical trials for liver cancer, ThermoDox® (Celsion Corporation) is a drug delivery system containing doxorubicin, a common anti-cancer agent, encapsulated within a thermally sensitive liposome designed to release its contents above 39.5° C. Activation of such an agent with the use of HIFU, which can generate localized heating non-invasively, would combine the benefits of targeted chemotherapy and hyperthermia while minimizing undesirable systemic side-effects. To that end, the resolution and reliability with which HIFU-induced hyperthermia can achieve Thermodox® release was investigated using a novel agar-based gel embedding liposomes at clinically relevant concentrations (0.02 mg/ml). The gel was exposed to 1.15 MHz HIFU (Sonic Concepts H102) using a range of clinically relevant pressure amplitudes (0-6 MPa peak rarefactional), duty cycles (10-100%) and exposure durations to identify optimal insonation conditions for complete doxorubicin release. The corresponding temperature profiles were mapped with 0.5 mm spatial resolution using an embedded needle thermocouple; drug release was quantified using fluorimetry. Complete release over the HIFU focal area was obtained for 6-s continuous wave exposure at 5.2 MPa peak rarefactional pressure, i.e. under exposure conditions for which the temperature exceeded 43° C throughout the focal volume. For a given HIFU energy input, both the final temperature reached and the rate of heating were found to affect release significantly. However, ThermoDox® release was achieved only due to thermal effects of HIFU, and not by other ultrasound effects, such as cavitation without heating, showing robustness of HIFU-induced hyperthermia as a release mechanism.

  17. Cryogenic Fluid Management Technology and Nuclear Thermal Propulsion

    NASA Technical Reports Server (NTRS)

    Taylor, Brian D.; Caffrey, Jarvis; Hedayat, Ali; Stephens, Jonathan; Polsgrove, Robert

    2016-01-01

    Cryogenic fluid management (CFM) is critical to the success of future nuclear thermal propulsion powered vehicles. While this is an issue for any propulsion system utilizing cryogenic propellants, this is made more challenging by the radiation flux produced by the reactor in a nuclear thermal rocket (NTR). Managing the cryogenic fuel to prevent propellant loss to boil off and leakage is needed to limit the required quantity of propellant to a reasonable level. Analysis shows deposition of energy into liquid hydrogen fuel tanks in the vicinity of the nuclear thermal engine. This is on top of ambient environment sources of heat. Investments in cryogenic/thermal management systems (some of which are ongoing at various organizations) are needed in parallel to nuclear thermal engine development in order to one day see the successful operation of an entire stage. High durability, low thermal conductivity insulation is one developmental need. Light weight cryocoolers capable of removing heat from large fluid volumes at temperatures as low as approx. 20 K are needed to remove heat leak from the propellant of an NTR. Valve leakage is an additional CFM issue of great importance. Leakage rates of state of the art, launch vehicle size valves (which is approximately the size valves needed for a Mars transfer vehicle) are quite high and would result in large quantities of lost propellant over a long duration mission. Additionally, the liquid acquisition system inside the propellant tank must deliver properly conditioned propellant to the feed line for successful engine operation and avoid intake of warm or gaseous propellant. Analysis of the thermal environment and the CFM technology development are discussed in the accompanying presentation.

  18. Vegetation management with fire modifies peatland soil thermal regime.

    PubMed

    Brown, Lee E; Palmer, Sheila M; Johnston, Kerrylyn; Holden, Joseph

    2015-05-01

    Vegetation removal with fire can alter the thermal regime of the land surface, leading to significant changes in biogeochemistry (e.g. carbon cycling) and soil hydrology. In the UK, large expanses of carbon-rich upland environments are managed to encourage increased abundance of red grouse (Lagopus lagopus scotica) by rotational burning of shrub vegetation. To date, though, there has not been any consideration of whether prescribed vegetation burning on peatlands modifies the thermal regime of the soil mass in the years after fire. In this study thermal regime was monitored across 12 burned peatland soil plots over an 18-month period, with the aim of (i) quantifying thermal dynamics between burned plots of different ages (from <2 to 15 + years post burning), and (ii) developing statistical models to determine the magnitude of thermal change caused by vegetation management. Compared to plots burned 15 + years previously, plots recently burned (<2-4 years) showed higher mean, maximum and range of soil temperatures, and lower minima. Statistical models (generalised least square regression) were developed to predict daily mean and maximum soil temperature in plots burned 15 + years prior to the study. These models were then applied to predict temperatures of plots burned 2, 4 and 7 years previously, with significant deviations from predicted temperatures illustrating the magnitude of burn management effects. Temperatures measured in soil plots burned <2 years previously showed significant statistical disturbances from model predictions, reaching +6.2 °C for daily mean temperatures and +19.6 °C for daily maxima. Soil temperatures in plots burnt 7 years previously were most similar to plots burned 15 + years ago indicating the potential for soil temperatures to recover as vegetation regrows. Our findings that prescribed peatland vegetation burning alters soil thermal regime should provide an impetus for further research to understand the consequences of thermal regime

  19. Thermal analysis and two-directional air flow thermal management for lithium-ion battery pack

    NASA Astrophysics Data System (ADS)

    Yu, Kuahai; Yang, Xi; Cheng, Yongzhou; Li, Changhao

    2014-12-01

    Thermal management is a routine but crucial strategy to ensure thermal stability and long-term durability of the lithium-ion batteries. An air-flow-integrated thermal management system is designed in the present study to dissipate heat generation and uniformize the distribution of temperature in the lithium-ion batteries. The system contains of two types of air ducts with independent intake channels and fans. One is to cool the batteries through the regular channel, and the other minimizes the heat accumulations in the middle pack of batteries through jet cooling. A three-dimensional anisotropic heat transfer model is developed to describe the thermal behavior of the lithium-ion batteries with the integration of heat generation theory, and validated through both simulations and experiments. Moreover, the simulations and experiments show that the maximum temperature can be decreased to 33.1 °C through the new thermal management system in comparison with 42.3 °C through the traditional ones, and temperature uniformity of the lithium-ion battery packs is enhanced, significantly.

  20. Active Extraction of Near-field Thermal Radiation

    NASA Astrophysics Data System (ADS)

    Ding, Ding; Kim, Taeyong; Minnich, Austin

    Radiative heat transport between materials supporting surface-phonon polaritons is greatly enhanced when the materials are placed at sub-wavelength separation as a result of the contribution of near-field surface modes. However, the enhancement is limited to small separations due to the evanescent decay of the surface waves. In this work, we propose and numerically demonstrate an active radiative cooling (ARC) scheme to extract these modes to the far-field. Our approach exploits the monochromatic nature of near-field thermal radiation to drive a transition in a laser gain medium, which, when coupled with external optical pumping, allows the resonant surface mode to be emitted into the far-field. We also provide further insights into our ARC scheme by applying the theoretical framework used for laser cooling of solids (LCS) to ARC. We show that LCS and ARC can be described with the same mathematical formalism by replacing the electron-phonon coupling parameter in LCS with the electron-photon coupling parameter in ARC. Using this framework, we examine the predictions of the formalism for LCS and ARC using realistic parameters and find that ARC can achieve higher efficiency and extracted power over a wide range of conditions. Our study demonstrates a new approach to manipulate near-field thermal radiation for thermal management.

  1. Parylene-based active micro space radiator with thermal contact switch

    SciTech Connect

    Ueno, Ai; Suzuki, Yuji

    2014-03-03

    Thermal management is crucial for highly functional spacecrafts exposed to large fluctuations of internal heat dissipation and/or thermal boundary conditions. Since thermal radiation is the only means for heat removal, effective control of radiation is required for advanced space missions. In the present study, a MEMS (Micro Electro Mechanical Systems) active radiator using the contact resistance change has been proposed. Unlike previous bulky thermal louvers/shutters, higher fill factor can be accomplished with an array of electrostatically driven micro diaphragms suspended with polymer tethers. With an early prototype developed with parylene MEMS technologies, radiation heat flux enhancement up to 42% has been achieved.

  2. Development of Passive Fuel Cell Thermal Management Technology

    NASA Technical Reports Server (NTRS)

    Burke, Kenneth A.; Jakupca, Ian; Colozza, Anthony

    2011-01-01

    The NASA Glenn Research Center is developing advanced passive thermal management technology to reduce the mass and improve the reliability of space fuel cell systems for the NASA exploration program. The passive thermal management system relies on heat conduction within the cooling plate to move the heat from the central portion of the cell stack out to the edges of the fuel cell stack rather than using a pumped loop cooling system to convectively remove the heat. Using the passive approach eliminates the need for a coolant pump and other cooling loop components which reduces fuel cell system mass and improves overall system reliability. Previous analysis had identified that low density, ultra-high thermal conductivity materials would be needed for the cooling plates in order to achieve the desired reductions in mass and the highly uniform thermal heat sink for each cell within a fuel cell stack. A pyrolytic graphite material was identified and fabricated into a thin plate using different methods. Also a development project with Thermacore, Inc. resulted in a planar heat pipe. Thermal conductivity tests were done using these materials. The results indicated that lightweight passive fuel cell cooling is feasible.

  3. Thermal management in inertial fusion energy slab amplifiers

    NASA Astrophysics Data System (ADS)

    Sutton, Steven B.; Albrecht, George F.

    1995-12-01

    As the technology associated with the development of solid-state drivers for inertial fusion energy (IFE) has evolved, increased emphasis has been placed on the development of an efficient approach for managing the waste heat generated in the laser media. This paper addresses the technical issues associated with the gas cooling of large aperture slabs, where the laser beam propagates through the cooling fluid. It is shown that the major consequence of proper thermal management is the introduction of simple wedge, or beam steering, into the system. Achieving proper thermal management requires careful consideration of the geometry, cooling fluid characteristics, cooling flow characteristics, as well as the thermal/mechanical/optical characteristics of the laser media. Particularly important are the effects of cooling rate variation and turbulent scattering on the system optical performance. Helium is shown to have an overwhelming advantage with respect to turbulent scattering losses. To mitigate cooling rate variations, we introduce the concept of flow conditioning. Finally, optical path length variations across the aperture are calculated. A comparison of two laser materials (S-FAP and YAG) shows the benefit of a nearly a-thermal material on optical variations in the system.

  4. An engineering code to analyze hypersonic thermal management systems

    NASA Astrophysics Data System (ADS)

    Vangriethuysen, Valerie J.; Wallace, Clark E.

    1993-11-01

    This paper will describe an effort that is underway within the Advanced Propulsion Division of the Aero Propulsion and Power Directorate at Wright Patterson AFB to develop an engineering computer code to aid in the development of hypersonic thermal management systems. The goal of the Vehicle Integrated Thermal Management Code (VITMAC), is to thermally model the entire thermal management system on an integrated basis for an entire vehicle. A further goal is for it to be a stand-alone code. In other words, to predict the aerodynamic heating on the vehicle surface during the trajectory, to the heat loads from the propulsion system, subsystems and avionics, and to the heat transfer through the structure and insulation. In addition, VITMAC will be able to model the flow of the coolant through the network. All this is to determine if the vehicle is thermally balanced and if there are any areas in risk of melting or thermal degradation. The code also has the option to accept user data for aerodynamic heating, heat loads and user-specific components. To aid the user while inputting the vehicle configuration, geometry, components, and 'plumbing' data, a graphical user interface is being incorporated within te code. This will enable the user, even those with little experience in the area, with the aid of a mouse, to literally see the network on the screen as it is being inputted. This capability will speed up the input process, particularly for complex systems, as well as aid in error detection. This paper will further discuss the architecture of VITMAC. Also discussed will be its developmental status and capabilities, computer system that supports the code, its relevancy to other types of vehicles and applications, expansion capability and future plans.

  5. Compton effect thermally activated depolarization dosimeter

    DOEpatents

    Moran, Paul R.

    1978-01-01

    A dosimetry technique for high-energy gamma radiation or X-radiation employs the Compton effect in conjunction with radiation-induced thermally activated depolarization phenomena. A dielectric material is disposed between two electrodes which are electrically short circuited to produce a dosimeter which is then exposed to the gamma or X radiation. The gamma or X-radiation impinging on the dosimeter interacts with the dielectric material directly or with the metal composing the electrode to produce Compton electrons which are emitted preferentially in the direction in which the radiation was traveling. A portion of these electrons becomes trapped in the dielectric material, consequently inducing a stable electrical polarization in the dielectric material. Subsequent heating of the exposed dosimeter to the point of onset of ionic conductivity with the electrodes still shorted through an ammeter causes the dielectric material to depolarize, and the depolarization signal so emitted can be measured and is proportional to the dose of radiation received by the dosimeter.

  6. Thermal Management Techniques for Oil-Free Turbomachinery Systems

    NASA Technical Reports Server (NTRS)

    Radil, Kevin; DellaCorte, Chris; Zeszotek, Michelle

    2006-01-01

    Tests were performed to evaluate three different methods of utilizing air to provide thermal management control for compliant journal foil air bearings. The effectiveness of the methods was based on bearing bulk temperature and axial thermal gradient reductions during air delivery. The first method utilized direct impingement of air on the inner surface of a hollow test journal during operation. The second, less indirect method achieved heat removal by blowing air inside the test journal to simulate air flowing axially through a hollow, rotating shaft. The third method emulated the most common approach to removing heat by forcing air axially through the bearing s support structure. Internal bearing temperatures were measured with three, type K thermocouples embedded in the bearing that measured general internal temperatures and axial thermal gradients. Testing was performed in a 1 atm, 260 C ambient environment with the bearing operating at 60 krpm and supporting a load of 222 N. Air volumetric flows of 0.06, 0.11, and 0.17 cubic meters per minute at approximately 150 to 200 C were used. The tests indicate that all three methods provide thermal management but at different levels of effectiveness. Axial cooling of the bearing support structure had a greater effect on bulk temperature for each air flow and demonstrated that the thermal gradients could be influenced by the directionality of the air flow. Direct air impingement on the journal's inside surface provided uniform reductions in both bulk temperature and thermal gradients. Similar to the direct method, indirect journal cooling had a uniform cooling effect on both bulk temperatures and thermal gradients but was the least effective of the three methods.

  7. Mechanics and thermal management of stretchable inorganic electronics

    PubMed Central

    Song, Jizhou; Feng, Xue; Huang, Yonggang

    2016-01-01

    Stretchable electronics enables lots of novel applications ranging from wearable electronics, curvilinear electronics to bio-integrated therapeutic devices that are not possible through conventional electronics that is rigid and flat in nature. One effective strategy to realize stretchable electronics exploits the design of inorganic semiconductor material in a stretchable format on an elastomeric substrate. In this review, we summarize the advances in mechanics and thermal management of stretchable electronics based on inorganic semiconductor materials. The mechanics and thermal models are very helpful in understanding the underlying physics associated with these systems, and they also provide design guidelines for the development of stretchable inorganic electronics. PMID:27547485

  8. Management applications for thermal IR imagery of lake processes

    NASA Technical Reports Server (NTRS)

    Whipple, J. M.; Haynes, R. B.

    1971-01-01

    A thermal infrared scanning program was conducted in the Lake Ontario Basin region in an effort to determine: (1) limonologic data that could be collected by remote sensing techniques, and (2) local interest in and routine use of such data in water management programs. Difficulties encountered in the development of an infrared survey program in New York suggest that some of the major obstacles to acceptance of remotely sensed data for routine use are factors of psychology rather than technology. Also, terminology used should suit the measurement technique in order to encourage acceptance of the surface thermal data obtained.

  9. Thermal management system options for high power space platforms

    NASA Technical Reports Server (NTRS)

    Sadunas, J. A.; Lehtinen, A.; Parish, R.

    1985-01-01

    Thermal Management System (TMS) design options for a high power (75kWe), low earth orbit, multimodule space platform were investigated. The approach taken was to establish a baseline TMS representative of current technology, and to make incremental improvements through successive subsystem trades that lead to a candidate TMS. The TMS trades included centralized and decentralized transport, single-phase and two-phase transport, alternate working fluids, liquid loop and heat pipe radiators, deployed fixed, body mounted and steerable radiators, and thermal storage. The subsystem options were evaluated against criteria such as weight, TMS power requirement, reliability, system isothermality penalty, and growth potential.

  10. Diamond/aluminium nitride composites for efficient thermal management applications

    SciTech Connect

    Cervenka, J.; Dontschuk, N.; Prawer, S.; Ladouceur, F.; Duvall, S. G.

    2012-07-30

    Synthetic diamond/AlN composite materials have been fabricated by a combination of microwave plasma-assisted chemical vapor deposition and molecular beam epitaxy. These wide band gap semiconductor heterojunctions show promises for many applications, including thermal management, deep ultraviolet light emitting devices, and high power and high temperature electronics. Here, we report results of an interface study of polycrystalline diamond layers grown on single crystal AlN(0001). High resolution transmission microscopy revealed atomically sharp interfaces between diamond and AlN. Temperature dependent Raman spectroscopy measurements showed reduced thermal resistance on diamond-coated AlN substrates compared to uncoated AlN at temperatures above 330 K.

  11. Diamond/aluminium nitride composites for efficient thermal management applications

    NASA Astrophysics Data System (ADS)

    Cervenka, J.; Dontschuk, N.; Ladouceur, F.; Duvall, S. G.; Prawer, S.

    2012-07-01

    Synthetic diamond/AlN composite materials have been fabricated by a combination of microwave plasma-assisted chemical vapor deposition and molecular beam epitaxy. These wide band gap semiconductor heterojunctions show promises for many applications, including thermal management, deep ultraviolet light emitting devices, and high power and high temperature electronics. Here, we report results of an interface study of polycrystalline diamond layers grown on single crystal AlN(0001). High resolution transmission microscopy revealed atomically sharp interfaces between diamond and AlN. Temperature dependent Raman spectroscopy measurements showed reduced thermal resistance on diamond-coated AlN substrates compared to uncoated AlN at temperatures above 330 K.

  12. Thermal and non-thermal fluctuations in active polar gels.

    PubMed

    Basu, A; Joanny, J F; Jülicher, F; Prost, J

    2008-10-01

    We discuss general features of noise and fluctuations in active polar gels close to and away from equilibrium. We use the single-component hydrodynamic theory of active polar gels built by Kruse and coworkers to describe the cytoskeleton in cells. Close to equilibrium, we calculate the response function of the gel to external fields and introduce Langevin forces in the constitutive equations with correlation functions respecting the fluctuation-dissipation theorem. We then discuss the breakage of the fluctuation-dissipation theorem due to an external field such as the activity of the motors. Active gels away from equilibrium are considered at the scaling level. As an example of application of the theory, we calculate the density correlation function (the dynamic structure factor) of a compressible active polar gel and discuss possible instabilities. PMID:18791871

  13. Process management using component thermal-hydraulic function classes

    DOEpatents

    Morman, J.A.; Wei, T.Y.C.; Reifman, J.

    1999-07-27

    A process management expert system where following malfunctioning of a component, such as a pump, for determining system realignment procedures such as for by-passing the malfunctioning component with on-line speeds to maintain operation of the process at full or partial capacity or to provide safe shut down of the system while isolating the malfunctioning component. The expert system uses thermal-hydraulic function classes at the component level for analyzing unanticipated as well as anticipated component malfunctions to provide recommended sequences of operator actions. Each component is classified according to its thermal-hydraulic function, and the generic and component-specific characteristics for that function. Using the diagnosis of the malfunctioning component and its thermal hydraulic class, the expert system analysis is carried out using generic thermal-hydraulic first principles. One aspect of the invention employs a qualitative physics-based forward search directed primarily downstream from the malfunctioning component in combination with a subsequent backward search directed primarily upstream from the serviced component. Generic classes of components are defined in the knowledge base according to the three thermal-hydraulic functions of mass, momentum and energy transfer and are used to determine possible realignment of component configurations in response to thermal-hydraulic function imbalance caused by the malfunctioning component. Each realignment to a new configuration produces the accompanying sequence of recommended operator actions. All possible new configurations are examined and a prioritized list of acceptable solutions is produced. 5 figs.

  14. Process management using component thermal-hydraulic function classes

    DOEpatents

    Morman, James A.; Wei, Thomas Y. C.; Reifman, Jaques

    1999-01-01

    A process management expert system where following malfunctioning of a component, such as a pump, for determining system realignment procedures such as for by-passing the malfunctioning component with on-line speeds to maintain operation of the process at full or partial capacity or to provide safe shut down of the system while isolating the malfunctioning component. The expert system uses thermal-hydraulic function classes at the component level for analyzing unanticipated as well as anticipated component malfunctions to provide recommended sequences of operator actions. Each component is classified according to its thermal-hydraulic function, and the generic and component-specific characteristics for that function. Using the diagnosis of the malfunctioning component and its thermal hydraulic class, the expert system analysis is carried out using generic thermal-hydraulic first principles. One aspect of the invention employs a qualitative physics-based forward search directed primarily downstream from the malfunctioning component in combination with a subsequent backward search directed primarily upstream from the serviced component. Generic classes of components are defined in the knowledge base according to the three thermal-hydraulic functions of mass, momentum and energy transfer and are used to determine possible realignment of component configurations in response to thermal-hydraulic function imbalance caused by the malfunctioning component. Each realignment to a new configuration produces the accompanying sequence of recommended operator actions. All possible new configurations are examined and a prioritized list of acceptable solutions is produced.

  15. Microgravity fluid management in two-phase thermal systems

    NASA Technical Reports Server (NTRS)

    Parish, Richard C.

    1987-01-01

    Initial studies have indicated that in comparison to an all liquid single phase system, a two-phase liquid/vapor thermal control system requires significantly lower pumping power, demonstrates more isothermal control characteristics, and allows greater operational flexibility in heat load placement. As a function of JSC's Work Package responsibility for thermal management of space station equipment external to the pressurized modules, prototype development programs were initiated on the Two-Phase Thermal Bus System (TBS) and the Space Erectable Radiator System (SERS). JSC currently has several programs underway to enhance the understanding of two-phase fluid flow characteristics. The objective of one of these programs (sponsored by the Microgravity Science and Applications Division at NASA-Headquarters) is to design, fabricate, and fly a two-phase flow regime mapping experiment in the Shuttle vehicle mid-deck. Another program, sponsored by OAST, involves the testing of a two-phase thermal transport loop aboard the KC-135 reduced gravity aircraft to identify system implications of pressure drop variation as a function of the flow quality and flow regime present in a representative thermal system.

  16. Process management using component thermal-hydraulic function classes

    SciTech Connect

    Morman, James A.; Wei, Thomas Y.C.; Reifman, Jaques

    1997-12-01

    A process management expert system for a nuclear, chemical or other process is effective following malfunctioning of a component, such as a pump, for determining system realignment procedures such as for by-passing the malfunctioning component with on-line speeds to maintain operation of the process at full or partial capacity or to provide safe shut down of the system while isolating the malfunctioning component. The expert system uses thermal-hydraulic function classes at the component level for analyzing unanticipated as well as anticipated component malfunctions to provide recommended sequences of operator actions. Each component is classified according to its thermal-hydraulic function, and the generic and component-specific characteristics for that function. Using the diagnosis of the malfunctioning component and its thermal hydraulic class, the expert system analysis is carried out using generic thermal-hydraulic first principles. One aspect of the invention employs a qualitative physics-based forward search directed primarily downstream from the malfunctioning component in combination with a subsequent backward search directed primarily upstream from the serviced component. Generic classes of components are defined in the knowledge base according to the three thermal-hydraulic functions of mass, momentum and energy transfer and are used to determine possible realignment of component configurations in response to thermal-hydraulic function imbalance caused by the malfunctioning component. The search process is based upon mass, momentum and energy conservation principles so that qualitative thermal-hydraulic fundamental principles are satisfied for new system configurations. Each realignment to a new configuration produces the accompanying sequence of recommended operator actions. All possible new configurations are examined and a prioritized list of acceptable solutions is produced.

  17. From Concept-to-Flight: An Active Active Fluid Loop Based Thermal Control System for Mars Science Laboratory Rover

    NASA Technical Reports Server (NTRS)

    Birur, Gajanana C.; Bhandari, Pradeep; Bame, David; Karlmann, Paul; Mastropietro, A. J.; Liu, Yuanming; Miller, Jennifer; Pauken, Michael; Lyra, Jacqueline

    2012-01-01

    The Mars Science Laboratory (MSL) rover, Curiosity, which was launched on November 26, 2011, incorporates a novel active thermal control system to keep the sensitive electronics and science instruments at safe operating and survival temperatures. While the diurnal temperature variations on the Mars surface range from -120 C to +30 C, the sensitive equipment are kept within -40 C to +50 C. The active thermal control system is based on a single-phase mechanically pumped fluid loop (MPFL) system which removes or recovers excess waste heat and manages it to maintain the sensitive equipment inside the rover at safe temperatures. This paper will describe the entire process of developing this active thermal control system for the MSL rover from concept to flight implementation. The development of the rover thermal control system during its architecture, design, fabrication, integration, testing, and launch is described.

  18. PREFACE: Eurotherm Seminar 102: Thermal Management of Electronic Systems

    NASA Astrophysics Data System (ADS)

    Punch, J.; Walsh, E.

    2014-07-01

    About EUROTHERM The aim of the EUROTHERM Committee (www.eurothermcommittee.eu) is to promote and foster European cooperation in Thermal Sciences and Heat Transfer by gathering together scientists and engineers working in specialized areas. The Committee consists of members representing and appointed by national bodies in the EU countries. The current President of EUROTHERM is Professor Anton van Steenhoven from the University of Eindhoven (The Netherlands). The Committee organizes and coordinates European scientific events such as the EUROTHERM Seminars (about 4 per year) and the European Thermal Sciences Conference (every 4 years). About EUROTHERM Seminar 102 (www.eurothermseminar102.com) This seminar, part of the long-running series of European seminars on the thermal sciences, took place in June 2014 at the University of Limerick in Limerick, Ireland. The seminar addressed the topic of 'Thermal Management of Electronic Systems', a critical contemporary application area which represents a vibrant challenge for practitioners of the thermal sciences. We convey special thanks to the reviewers who have evaluated these papers. We also thank the scientific committee, consisting of internationally recognized experts. Their role has been to manage the evaluation of abstracts and the papers selection process as co-coordinators for specific topics. This seminar was hosted by the Stokes Institute at the University of Limerick. It could not have been organized without the efficient help of our administrators and technicians for IT support. This volume of Journal of Physics: Conference Series includes 27 articles presented at the seminar. Dr. Jeff Punch, Chair Stokes Institute, University of Limerick, Limerick, Ireland Email: jeff.punch@ul.ie Prof. Edmond Walsh, Co-Chair Associate Professor, Osney Laboratories, Department of Engineering Science, University of Oxford, UK Email: edmond.walsh@bnc.ox.ac.uk

  19. A review of thermal performance improving methods of lithium ion battery: Electrode modification and thermal management system

    NASA Astrophysics Data System (ADS)

    Zhao, Rui; Zhang, Sijie; Liu, Jie; Gu, Junjie

    2015-12-01

    Lithium ion (Li-ion) battery has emerged as an important power source for portable devices and electric vehicles due to its superiority over other energy storage technologies. A mild temperature variation as well as a proper operating temperature range are essential for a Li-ion battery to perform soundly and have a long service life. In this review paper, the heat generation and dissipation of Li-ion battery are firstly analyzed based on the energy conservation equations, followed by an examination of the hazardous effects of an above normal operating temperature. Then, advanced techniques in respect of electrode modification and systematic battery thermal management are inspected in detail as solutions in terms of reducing internal heat production and accelerating external heat dissipation, respectively. Specifically, variable parameters like electrode thickness and particle size of active material, along with optimization methods such as coating, doping, and adding conductive media are discussed in the electrode modification section, while the current development in air cooling, liquid cooling, heat pipe cooling, and phase change material cooling systems are reviewed in the thermal management part as different ways to improve the thermal performance of Li-ion batteries.

  20. Heat balance and thermal management of the TMT Observatory

    NASA Astrophysics Data System (ADS)

    Thompson, Hugh; Vogiatzis, Konstantinos

    2014-08-01

    An extensive campaign of aero-thermal modeling of the Thirty Meter Telescope (TMT) has been carried out and presented in other papers. This paper presents a summary view of overall heat balance of the TMT observatory. A key component of this heat balance that can be managed is the internal sources of heat dissipation to the ambient air inside the enclosure. An engineering budget for both daytime and nighttime sources is presented. This budget is used to ensure that the overall effects on daytime cooling and nighttime seeing are tracked and fall within the modeled results that demonstrate that the observatory meets its performance requirements. In the daytime heat fluxes from air-conditioning, solar loading, infiltration, and deliberate venting through the enclosure top vent are included along with equipment heat sources. In the nighttime convective heat fluxes through the open aperture and vent doors, as well as radiation to the sky are tracked along with the nighttime residual heat dissipations after cooling from equipment in the observatory. The diurnal variation of thermal inertia of large masses, such as the telescope structure, is also included. Model results as well as the overall heat balance and thermal management strategy of the observatory are presented.

  1. Cryogenic Thermal Management Advances during the CRYOTOOL Program

    NASA Astrophysics Data System (ADS)

    Bugby, D.; Stouffer, C.; Garzon, J.; Beres, M.; Gilchrist, A.; Roberts, T.; Davis, T.

    2006-04-01

    This paper describes the cryogenic thermal management advances made during the AFRL-sponsored CRYOTOOL program. Advances occurred as a result of conducting four technology development tasks: (1) development of a differential thermal expansion cryogenic thermal switch (DTE-CTSW) made with high purity Al end-pieces and an Ultem support rod; (2) carrying out of a dual DTE-CTSW/dual cryocooler performance test to quantify CTSW benefits in a redundant cryocooler system; (3) development of a miniaturized cryogenic loop heat pipe (mini-CLHP) that combines flex link, conduction bar, and CTSW functionalities; and (4) development of an across-gimbal cryogenic thermal transport system (GCTTS) with large diameter transport line coils for optics cooling. The results are as follows. The DTE-CTSW achieved an ON conductance of 2-3.6 W/K (from 35-90 K) and an OFF resistance of 1100-2300 K/W (300-230 K warm end). The redundant cryocooler test showed modest parasitic heat leak savings when dual DTE-CTSWs were used versus when they were not used. The mini-CLHP, using neon as the working fluid, transported 2.5 W at 35 K, achieved an OFF resistance of 1555 K/W, and had cross/axial flexibilities of 100-450 N/m. Lastly, GCTTS, using nitrogen as the working fluid, transported 20 W at 100 K in a flat configuration. Additional work is needed to verify GCTTS operation in an elevated orientation.

  2. Joining and Integration of Advanced Carbon-Carbon Composites to Metallic Systems for Thermal Management Applications

    NASA Technical Reports Server (NTRS)

    Singh, M.; Asthana, R.

    2008-01-01

    Recent research and development activities in joining and integration of carbon-carbon (C/C) composites to metals such as Ti and Cu-clad-Mo for thermal management applications are presented with focus on advanced brazing techniques. A wide variety of carbon-carbon composites with CVI and resin-derived matrices were joined to Ti and Cu-clad Mo using a number of active braze alloys. The brazed joints revealed good interfacial bonding, preferential precipitation of active elements (e.g., Ti) at the composite/braze interface. Extensive braze penetration of the inter-fiber channels in the CVI C/C composites was observed. The chemical and thermomechanical compatibility between C/C and metals at elevated temperatures is assessed. The role of residual stresses and thermal conduction in brazed C/C joints is discussed. Theoretical predictions of the effective thermal resistance suggest that composite-to-metal brazed joints may be promising for lightweight thermal management applications.

  3. Annual Report: Turbine Thermal Management (30 September 2013)

    SciTech Connect

    Alvin, Mary Anne; Richards, George

    2014-04-10

    The FY13 NETL-RUA Turbine Thermal Management effort supported the Department of Energy’s (DOE) Hydrogen Turbine Program through conduct of novel, fundamental, basic, and applied research in the areas of aerothermal heat transfer, coatings development, and secondary flow control. This research project utilized the extensive expertise and facilities readily available at NETL and the participating universities. The research approach included explorative studies based on scaled models and prototype coupon tests conducted under realistic high-temperature, pressurized, turbine operating conditions. This research is expected to render measurable outcomes that will meet DOE’s advanced turbine development goals of a 3- to 5-point increase in power island efficiency and a 30 percent power increase above the hydrogen-fired combined cycle baseline. In addition, knowledge gained from this project will further advance the aerothermal cooling and TBC technologies in the general turbine community. This project has been structured to address: • Development and design of aerothermal and materials concepts in FY12-13. • Design and manufacturing of these advanced concepts in FY13. • Bench-scale/proof-of-concept testing of these concepts in FY13-14 and beyond. In addition to a Project Management task, the Turbine Thermal Management project consists of four tasks that focus on a critical technology development in the areas of heat transfer, materials development, and secondary flow control. These include: • Aerothermal and Heat Transfer • Coatings and Materials Development • Design Integration and Testing • Secondary Flow Rotating Rig.

  4. A new active thermal neutron detector.

    PubMed

    Bedogni, R; Bortot, D; Pola, A; Introini, M V; Gentile, A; Esposito, A; Gómez-Ros, J M; Palomba, M; Grossi, A

    2014-10-01

    This communication presents the main results about the design and in-house fabrication of a new solid-state neutron detector, which produces a DC output signal proportional to the thermal neutron fluence rate. The detector has been developed within the framework of the 3-y project NESCOFI@BTF of INFN (CSN V). Due to its sensitivity, photon rejection, low cost and minimum size, this device is suited to be used in moderator-based spectrometers. PMID:24345462

  5. A miniature shock-activated thermal battery for munitions applications

    SciTech Connect

    Guidotti, R.A.; Kirby, D.L.; Reinhardt, F.W.

    1998-04-01

    The feasibility of a small, fast-rise thermal battery for non-spinning munitions applications was examined by studying the response of conventional thermal cells to impact (mechanical) energy to simulate a setback environment. This is an extension of earlier work that demonstrated that shock activation could be used to produce power from a conventional thermal-battery cell. The results of tests with both single and multiple cells are presented, along with data for a 5-cell miniature (5-mm diameter) thermal battery. The issues needing to be resolved before such a device can become a commercial reality are also discussed.

  6. Study of thermal management for space platform applications

    NASA Technical Reports Server (NTRS)

    Oren, J. A.

    1980-01-01

    Techniques for the management of the thermal energy of large space platforms using many hundreds of kilowatts over a 10 year life span were evaluated. Concepts for heat rejection, heat transport within the vehicle, and interfacing were analyzed and compared. The heat rejection systems were parametrically weight optimized over conditions for heat pipe and pumped fluid approaches. Two approaches to achieve reliability were compared for: performance, weight, volume, projected area, reliability, cost, and operational characteristics. Technology needs are assessed and technology advancement recommendations are made.

  7. Thermometry and thermal management of carbon nanotube circuits

    SciTech Connect

    Mayle, Scott; Gupta, Tanuj; Davis, Sam; Chandrasekhar, Venkat; Shafraniuk, Serhii

    2015-05-21

    Monitoring of the intrinsic temperature and the thermal management is discussed for the carbon nanotube nano-circuits. The experimental results concerning fabricating and testing of a thermometer able to monitor the intrinsic temperature on nanoscale are reported. We also suggest a model which describes a bi-metal multilayer system able to filter the heat flow, based on separating the electron and phonon components one from another. The bi-metal multilayer structure minimizes the phonon component of the heat flow, while retaining the electronic part. The method allows one to improve the overall performance of the electronic nano-circuits due to minimizing the energy dissipation.

  8. SSTAC/ARTS review of the draft Integrated Technology Plan (ITP). Volume 3: Space power and thermal management

    NASA Technical Reports Server (NTRS)

    1991-01-01

    Viewgraphs of briefings from the SSTAC/ARTS review of the draft integrated technology plan on thermal power and thermal management are presented. Topics covered include: space energy conversion research and technology; space photovoltaic energy conversion; chemical energy conversion and storage; thermal energy conversion; power management; thermal management; space nuclear power; high capacity power; surface power and thermal management; space platforms power and thermal management; and project SELENE.

  9. SSTAC/ARTS review of the draft Integrated Technology Plan (ITP). Volume 3: Space power and thermal management

    SciTech Connect

    Not Available

    1991-06-01

    Viewgraphs of briefings from the SSTAC/ARTS review of the draft integrated technology plan on thermal power and thermal management are presented. Topics covered include: space energy conversion research and technology; space photovoltaic energy conversion; chemical energy conversion and storage; thermal energy conversion; power management; thermal management; space nuclear power; high capacity power; surface power and thermal management; space platforms power and thermal management; and project SELENE.

  10. Thermal activation in a two-dimensional potential

    SciTech Connect

    Han, S.; Lapointe, J.; Lukens, J.E. )

    1989-10-16

    Measurements have been made of the transition rates between fluxoid states of a system with two Josephson junctions having two macroscopic degrees of freedom. The data, taken over a temperature range of 0.85 to 4.41 K, are in excellent agreement with the predictions for thermally activated transitions. No evidence is seen for recently reported apparent rate suppression below that predicted for thermal activation.

  11. Data base management systems activities

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The Data Management System-1100 is designed to operate in conjunction with the UNIVAC 1100 Series Operating System on any 1100 Series computer. DMS-1100 is divided into the following four major software components: (1) Data Definition Languages (DDL); (2) Data Management Routine (DMR); (3) Data Manipulation Languages (DML); and (4) Data Base Utilities (DBU). These software components are described in detail.

  12. Micro- and Nano-Scale Electrically Driven Two-Phase Thermal Management

    NASA Technical Reports Server (NTRS)

    Didion, Jeffrey R.

    2016-01-01

    This presentation discusses ground based proof of concept hardware under development at NASA GSFC to address high heat flux thermal management in silicon substrates. The goal is to develop proof of concept hardware for space flight validation. The space flight hardware will provide gravity insensitive thermal management for electronics applications such as transmit receive modules that are severely limited by thermal concerns.

  13. Successful thermal management of a totally implantable ventricular assist system.

    PubMed

    Tasai, K; Takatani, S; Orime, Y; Damm, G; Ohara, Y; Naito, K; Makinouchi, K; Mizuguchi, K; Matsuda, Y; Shimono, T

    1994-01-01

    Thermal management of the implantable ventricular assist system (VAS) is important not only from the pathophysiological point of view but also from the standpoint of system endurance. The heat distribution within the Baylor VAS was measured using different motor housing materials and environmental conditions. The temperature of the circulating water in the mock loop was set at 37 degrees and 42 degrees C. A polycarbonate motor housing was not a suitable material because of the high temperature development in the actuation system. An anodized aluminum housing demonstrated excellent heat conductivity. The surface temperature of this motor housing was 41.6 degrees C when immersed in circulating water at 42 degrees C. Heat conduction from the motor to the circulating blood revealed an effective thermal path. In the worst case, the heat flux of the motor to the circulating blood revealed an effective thermal path. In the worst case, the heat flux of the motor housing was calculated to be less than 0.062 W/cm2--an acceptable level for the surrounding tissues. PMID:8141658

  14. Utilizing Radioisotope Power System Waste Heat for Spacecraft Thermal Management

    NASA Technical Reports Server (NTRS)

    Pantano, David R.; Dottore, Frank; Tobery, E. Wayne; Geng, Steven M.; Schreiber, Jeffrey G.; Palko, Joseph L.

    2005-01-01

    An advantage of using a Radioisotope Power System (RPS) for deep space or planetary surface missions is the readily available waste heat, which can be used for a number of beneficial purposes including: maintaining electronic components within a controlled temperature range, warming propulsion tanks and mobility actuators, and maintaining liquid propellants above their freezing temperature. Previous missions using Radioisotope Thermoelectric Generators (RTGs) dissipated large quantities of waste heat due to the low efficiency of the thermoelectric conversion technology. The next generation RPSs, such as the 110-Watt Stirling Radioisotope Generator (SRG110) will have higher conversion efficiencies, thereby rejecting less waste heat at a lower temperature and may require alternate approaches to transferring waste heat to the spacecraft. RTGs, with efficiencies of 6 to 7 percent, reject their waste heat at the relatively high heat rejection temperature of 200 C. This is an advantage when rejecting heat to space; however, transferring heat to the internal spacecraft components requires a large and heavy radiator heat exchanger. At the same time, sensitive spacecraft instruments must be shielded from the thermal radiation of the RTG. The SRG110, with an efficiency around 22 percent and 50 C nominal housing surface temperature, can readily transfer the available waste heat directly via heat pipes, thermal straps, or fluid loops. The lower temperatures associated with the SRG110 avoid the chances of overheating other scientific components, eliminating the need for thermal shields. This provides the spacecraft designers more flexibility when locating the generator for a specific mission. A common misconception with high-efficiency systems is that there is not enough waste heat for spacecraft thermal management. This paper will dispel this misconception and investigate the use of a high-efficiency SRG110 for spacecraft thermal management and outline potential methods of

  15. Thermal management in high average power pulsed compression systems

    SciTech Connect

    Wavrik, R.W.; Reed, K.W.; Harjes, H.C.; Weber, G.J.; Butler, M.; Penn, K.J.; Neau, E.L.

    1992-08-01

    High average power repetitively pulsed compression systems offer a potential source of electron beams which may be applied to sterilization of wastes, treatment of food products, and other environmental and consumer applications. At Sandia National Laboratory, the Repetitive High Energy Pulsed Power (RHEPP) program is developing a 7 stage magnetic pulse compressor driving a linear induction voltage adder with an electron beam diode load. The RHEPP machine is being design to deliver 350 kW of average power to the diode in 60 ns FWHM, 2.5 MV, 3 kJ pulses at a repetition rate of 120 Hz. In addition to the electrical design considerations, the repetition rate requires thermal management of the electrical losses. Steady state temperatures must be kept below the material degradation temperatures to maximize reliability and component life. The optimum design is a trade off between thermal management, maximizing overall electrical performance of the system, reliability, and cost effectiveness. Cooling requirements and configurations were developed for each of the subsystems of RHEPP. Finite element models that combine fluid flow and heat transfer were used to screen design concepts. The analysis includes one, two, and three dimensional heat transfer using surface heat transfer coefficients and boundary layer models. Experiments were conducted to verify the models as well as to evaluate cooling channel fabrication materials and techniques in Metglas wound cores. 10 refs.

  16. Thermal management in high average power pulsed compression systems

    SciTech Connect

    Wavrik, R.W.; Reed, K.W.; Harjes, H.C.; Weber, G.J.; Butler, M.; Penn, K.J.; Neau, E.L.

    1992-01-01

    High average power repetitively pulsed compression systems offer a potential source of electron beams which may be applied to sterilization of wastes, treatment of food products, and other environmental and consumer applications. At Sandia National Laboratory, the Repetitive High Energy Pulsed Power (RHEPP) program is developing a 7 stage magnetic pulse compressor driving a linear induction voltage adder with an electron beam diode load. The RHEPP machine is being design to deliver 350 kW of average power to the diode in 60 ns FWHM, 2.5 MV, 3 kJ pulses at a repetition rate of 120 Hz. In addition to the electrical design considerations, the repetition rate requires thermal management of the electrical losses. Steady state temperatures must be kept below the material degradation temperatures to maximize reliability and component life. The optimum design is a trade off between thermal management, maximizing overall electrical performance of the system, reliability, and cost effectiveness. Cooling requirements and configurations were developed for each of the subsystems of RHEPP. Finite element models that combine fluid flow and heat transfer were used to screen design concepts. The analysis includes one, two, and three dimensional heat transfer using surface heat transfer coefficients and boundary layer models. Experiments were conducted to verify the models as well as to evaluate cooling channel fabrication materials and techniques in Metglas wound cores. 10 refs.

  17. Thermal management of the adsorption-based vessel for hydrogeneous gas storage

    NASA Astrophysics Data System (ADS)

    Vasiliev, L. L.; Kanonchik, L. E.; Babenko, V. A.

    2012-09-01

    Thermal management is a design bottleneck in the creation of rational gas storage sorption systems. Inefficient heat transfer in a sorption bed is connected with a relatively low thermal conductivity (0.1-0.5 W/(mṡK)) and an appreciable sorption heat of activated gas storage materials. This work is devoted to the development of a thermally regulated onboard system of hydrogenous gas (methane and hydrogen) storage with the use of novel carbon sorbents. A hydrogenous gas storage system based on combined gas adsorption and compression at moderate pressures (3-6 MPa) and low temperatures (from the temperature of liquid nitrogen of about 77 K to a temperature of 273 K) is suggested.

  18. Transition temperature range of thermally activated nickel-titanium archwires

    PubMed Central

    SPINI, Tatiana Sobottka; VALARELLI, Fabrício Pinelli; CANÇADO, Rodrigo Hermont; de FREITAS, Karina Maria Salvatore; VILLARINHO, Denis Jardim

    2014-01-01

    Objectives The shape memory resulting from the superelasticity and thermoelastic effect is the main characteristic of thermally activated NiTi archwires and is closely related to the transition temperature range (TTR). The aim of this study was to evaluate the TTR of thermally activated NiTi archwires commercially available. Material and Methods Seven different brands of 0.019"x0.025" thermally activated nickel-titanium archwires were tested as received by differential scanning calorimetry (DSC) over the temperature range from -100°C to 150°C at 10°C/min. Results All thermally activated NiTi archwires analyzed presented stage transformation during thermal scanning with final austenitic temperature (Af) ranging from 20.39°C to 45.42°C. Three brands of NiTi archwires presented Af close to the room temperature and, this way, do not present properties of shape memory and pseudoelasticity that are desirable in clinical applications. Conclusions The thermally activated NiTi archwires present great variability in the TTR and the elastic parameters of each NiTi archwire should be provided by the manufacturers, to allow achievement of the best clinical performance possible. PMID:24676581

  19. Loss of Shallow Geothermal Resources in Urban Environment Due to the Absence of Thermal Management Policies

    NASA Astrophysics Data System (ADS)

    García-Gil, A.; Vázquez-Suñé, E.; Sánchez-Navarro, J. A.

    2014-12-01

    Shallow geothermal energy resources are of interest worldwide for the development of strategies against climate change. The current regulative framework for the sustainable implementation of the technologies exploiting this resources is facing several barriers. In the case of groundwater heat pumps, the thermal interference between exploitations may be endangering their feasibility in urban environments. Uncertainty in prediction of the sustainability of shallow geothermal energy development in urban groundwater bodies stems from the absence of a scientific-based legal regulatory framework which protects stakeholders from thermal interferences between existent exploitations systems. The present work consists of a numerical study aimed at understanding and predicting the thermal interference between groundwater heat pumps where several induced heat plumes in an urban ground water body coalesce, thus generating a heat island effect. A transient groundwater flow and heat transport model was developed to reproduce complex high-resolution data obtained from local monitoring specifically designed to control the aquifer respond to geothermal exploitation. The model aims to reproduce the groundwater flow and heat transport processes in a shallow alluvial aquifer exploited by 27 groundwater heat pumps and influenced by a river-aquifer relationship dominated by flood events mainly occurring in winter when the surface temperature is between 3 and 10 ºC. The results from the simulations have quantified the time-space thermal interference between exploitation systems and the consequences of river-aquifer thermal exchange. The results obtained showed the complexity of thermal management of the aquifer due to the transient activity of exploitations over space and time. With the actual exploitation regime of shallow geothermal resources in the investigated area the model predicts a temperature rising tendency in the production wells until 2019 which can compromise the coefficient

  20. Utilizing Radioisotope Power System Waste Heat for Spacecraft Thermal Management

    NASA Technical Reports Server (NTRS)

    Pantano, David R.; Dottore, Frank; Geng, Steven M.; Schrieber, Jeffrey G.; Tobery, E. Wayne; Palko, Joseph L.

    2005-01-01

    One of the advantages of using a Radioisotope Power System (RPS) for deep space or planetary surface missions is the readily available waste heat, which can be used to maintain electronic components within a controlled temperature range, to warm propulsion tanks and mobility actuators, and to gasify liquid propellants. Previous missions using Radioisotope Thermoelectric Generators (RTGs) dissipated a very large quantity of waste heat due to the relatively low efficiency of the thermoelectric conversion technology. The next generation RPSs, such as the 110-watt Stirling Radioisotope Generator (SRG110) will have much higher conversion efficiencies than their predecessors and therefore may require alternate approaches to transferring waste heat to the spacecraft. RTGs, with efficiencies of approx. 6 to 7% and 200 C housing surface temperatures, would need to use large and heavy radiator heat exchangers to transfer the waste heat to the internal spacecraft components. At the same time, sensitive spacecraft instruments must be shielded from the thermal radiation by using the heat exchangers or additional shields. The SRG110, with an efficiency around 22% and 50 C nominal housing surface temperature, can use the available waste heat more efficiently by more direct heat transfer methods such as heat pipes, thermal straps, or fluid loops. The lower temperatures allow the SRG110 much more flexibility to the spacecraft designers in configuring the generator without concern of overheating nearby scientific instruments, thereby eliminating the need for thermal shields. This paper will investigate using a high efficiency SRG110 for spacecraft thermal management and outline potential methods in several conceptual missions (Lunar Rover, Mars Rover, and Titan Lander) to illustrate the advantages with regard to ease of assembly, less complex interfaces, and overall mass savings.

  1. Thermally Activated Desiccant Technology for Heat Recovery and Comfort

    SciTech Connect

    Jalalzadeh, A. A.

    2005-11-01

    Desiccant cooling is an important part of the diverse portfolio of Thermally Activated Technologies (TAT) designed for conversion of heat for the purpose of indoor air quality control. Thermally activated desiccant cooling incorporates a desiccant material that undergoes a cyclic process involving direct dehumidification of moist air and thermal regeneration. Desiccants fall into two categories: liquid and solid desiccants. Regardless of the type, solid or liquid, the governing principles of desiccant dehumidification systems are the same. In the dehumidification process, the vapor pressure of the moist air is higher than that of the desiccant, leading to transfer of moisture from the air to the desiccant material. By heating the desiccant, the vapor pressure differential is reversed in the regeneration process that drives the moisture from the desiccant. Figure 1 illustrates a rotary solid-desiccant dehumidifier. A burner or a thermally compatible source of waste heat can provide the required heat for regeneration.

  2. Integrated Vehicle Thermal Management - Combining Fluid Loops in Electric Drive Vehicles (Presentation)

    SciTech Connect

    Rugh, J. P.

    2013-07-01

    Plug-in hybrid electric vehicles and electric vehicles have increased vehicle thermal management complexity, using separate coolant loop for advanced power electronics and electric motors. Additional thermal components result in higher costs. Multiple cooling loops lead to reduced range due to increased weight. Energy is required to meet thermal requirements. This presentation for the 2013 Annual Merit Review discusses integrated vehicle thermal management by combining fluid loops in electric drive vehicles.

  3. Thermal management of masks for deep x-ray lithography.

    SciTech Connect

    Khounsary, A.; Chojnowski, D.; Mancini, D.C.; Lai, B.; Dejus, R.

    1997-11-18

    This paper addresses some options and techniques in the thermal management of masks used in deep x-ray lithography. The x-ray masks are thin plates made of low-atomic-number materials on which a patterned thin film of a high-atomic-number metal has been deposited. When they are exposed to an x-ray beam, part of the radiation is transmitted to replicate the pattern on a downstream photoresist, and the remainder is absorbed in the mask in the form of heat. This heat load can cause deformation of the mask and thus image distortion in the lithography process. The mask geometry considered in the present study is 100 mm x 100 mm in area, and about 0.1 to 2 mm thick. The incident radiation is a bending magnet x-ray beam having a footprint of 60 mm x 4 mm at the mask. The mask is scanned vertically about {+-} 30 mm so that a 60 mm x 60 mm area is exposed. the maximum absorbed heat load in the mask is 80 W, which is significantly greater than a few watts encountered in previous systems. In this paper, cooling techniques, substrate material selection, transient and steady state thermal and structural behavior, and other thermo-mechanical aspects of mask design are discussed. It is shown that, while diamond and graphite remain attractive candidates, at present beryllium is a more suitable material for this purpose and, when properly cooled, can provide the necessary dimensional tolerance.

  4. A Novel Silicon Micromachined Integrated MCM Thermal Management System

    NASA Technical Reports Server (NTRS)

    Kazmierczak, M. J.; Henderson, H. T.; Gerner, F. M.

    1999-01-01

    This research concerned the development of a novel porous wick, fabricated totally out of silicon, using state-of-the-art MEMS technology. A comprehensive summary of results, as well as additional fabrication details, can be found in the following three documents located in the attached Appendices: A) Selected pages and excerpts from Year 2 progress report of the principal NASA Grant awarded from NASA Lewis Research Center, Grant Number NAG3-1706 entitled "A Novel Silicon Nficromachined Integrated MCM Thermal Management System" submitted to NASA LRC on 4/4/98. B) Selected viewgraphs from the joint NASA, TEES, and UC meeting held at the University of Cincinnati on April 24, 1998. C) Pre-print of the paper entitled "Coherent Macro Porous Silicon as a Wick Structure in an Integrated Nficrofluidic Two-Phase Cooling System" to be presented September 20-25, 1998 at the SPIE conference held in Santa Clara, Ca. To summarize,. nearly all of the proposed work was successfully accomplished (albeit a 3-month time extension was required), proving that micromachining can indeed be used to fabricate porous silicon wick structures with precise hole sizes and patterning control, thus permitting a substantial improvement in future wick designs. In addition, the appropriate range of thermal conductivities of the porous samples were theoretically predicted (see Appendix A). Although not part of the scope of work, the permeability of the test samples were measured (see results sections of Appendices B and C).

  5. Thermal management of closed computer modules utilizing high density circuitry. [in Airborne Information Management System

    NASA Technical Reports Server (NTRS)

    Hoadley, A. W.; Porter, A. J.

    1990-01-01

    This paper presents data on a preliminary analysis of the thermal dynamic characteristics of the Airborne Information Management System (AIMS), which is a continuing design project at NASA Dryden. The analysis established the methods which will be applied to the actual AIMS boards as they become available. The paper also describes the AIMS liquid cooling system design and presents a thermodynamic computer model of the AIMS cooling system, together with an experimental validation of this model.

  6. Cryogenic Fluid Management Technology Development for Nuclear Thermal Propulsion

    NASA Technical Reports Server (NTRS)

    Taylor, Brian; Caffrey, Jarvis; Hedayat, Ali; Stephens, Jonathan; Polsgrove, Robert

    2015-01-01

    The purpose of this paper is to investigate, facilitate a discussion and determine a path forward for technology development of cryogenic fluid management technology that is necessary for long duration deep space missions utilizing nuclear thermal propulsion systems. There are a number of challenges in managing cryogenic liquids that must be addressed before long durations missions into deep space, such as a trip to Mars can be successful. The leakage rate of hydrogen from pressure vessels, seals, lines and valves is a critical factor that must be controlled and minimized. For long duration missions, hydrogen leakage amounts to large increases in hydrogen and therefore vehicle mass. The size of a deep space vehicle, such as a mars transfer vehicle, must be kept small to control cost and the logistics of a multi launch, assembled in orbit vehicle. The boil off control of the cryogenic fluid is an additional obstacle to long duration missions. The boil off caused by heat absorption results in the growth of the propellant needs of the vehicle and therefore vehicle mass. This is a significant problem for a vehicle using nuclear (fission) propulsion systems. Radiation from the engines deposits large quantities of heat into the cryogenic fluid, greatly increasing boil off beyond that caused by environmental heat leakage. Addressing and resolving these challenges is critical to successful long duration space exploration. This paper discusses the state of the technology needed to address these challenges and discuss the path forward needed in technology development.

  7. Human suspicious activity recognition in thermal infrared video

    NASA Astrophysics Data System (ADS)

    Hossen, Jakir; Jacobs, Eddie; Chowdhury, Fahmida K.

    2014-10-01

    Detecting suspicious behaviors is important for surveillance and monitoring systems. In this paper, we investigate suspicious activity detection in thermal infrared imagery, where human motion can be easily detected from the background regardless of the lighting conditions and colors of the human clothing and surfaces. We use locally adaptive regression kernels (LARK) as patch descriptors, which capture the underlying local structure of the data exceedingly well, even in the presence of significant distortions. Patch descriptors are generated for each query patch and for each database patch. A statistical approach is used to match the query activity with the database to make the decision of suspicious activity. Human activity videos in different condition such as, walking, running, carrying a gun, crawling, and carrying backpack in different terrains were acquired using thermal infrared camera. These videos are used for training and performance evaluation of the algorithm. Experimental results show that the proposed approach achieves good performance in suspicious activity recognition.

  8. Active Thermal Extraction and Temperature Sensing of Near-field Thermal Radiation

    PubMed Central

    Ding, D.; Kim, T.; Minnich, A. J.

    2016-01-01

    Recently, we proposed an active thermal extraction (ATX) scheme that enables thermally populated surface phonon polaritons to escape into the far-field. The concept is based on a fluorescence upconversion process that also occurs in laser cooling of solids (LCS). Here, we present a generalized analysis of our scheme using the theoretical framework for LCS. We show that both LCS and ATX can be described with the same mathematical formalism by replacing the electron-phonon coupling parameter in LCS with the electron-photon coupling parameter in ATX. Using this framework, we compare the ideal efficiency and power extracted for the two schemes and examine the parasitic loss mechanisms. This work advances the application of ATX to manipulate near-field thermal radiation for applications such as temperature sensing and active radiative cooling. PMID:27595609

  9. Active Thermal Extraction and Temperature Sensing of Near-field Thermal Radiation.

    PubMed

    Ding, D; Kim, T; Minnich, A J

    2016-01-01

    Recently, we proposed an active thermal extraction (ATX) scheme that enables thermally populated surface phonon polaritons to escape into the far-field. The concept is based on a fluorescence upconversion process that also occurs in laser cooling of solids (LCS). Here, we present a generalized analysis of our scheme using the theoretical framework for LCS. We show that both LCS and ATX can be described with the same mathematical formalism by replacing the electron-phonon coupling parameter in LCS with the electron-photon coupling parameter in ATX. Using this framework, we compare the ideal efficiency and power extracted for the two schemes and examine the parasitic loss mechanisms. This work advances the application of ATX to manipulate near-field thermal radiation for applications such as temperature sensing and active radiative cooling. PMID:27595609

  10. Computational thermal, chemical, fluid, and solid mechanics for geosystems management.

    SciTech Connect

    Davison, Scott; Alger, Nicholas; Turner, Daniel Zack; Subia, Samuel Ramirez; Carnes, Brian; Martinez, Mario J.; Notz, Patrick K.; Klise, Katherine A.; Stone, Charles Michael; Field, Richard V., Jr.; Newell, Pania; Jove-Colon, Carlos F.; Red-Horse, John Robert; Bishop, Joseph E.; Dewers, Thomas A.; Hopkins, Polly L.; Mesh, Mikhail; Bean, James E.; Moffat, Harry K.; Yoon, Hongkyu

    2011-09-01

    This document summarizes research performed under the SNL LDRD entitled - Computational Mechanics for Geosystems Management to Support the Energy and Natural Resources Mission. The main accomplishment was development of a foundational SNL capability for computational thermal, chemical, fluid, and solid mechanics analysis of geosystems. The code was developed within the SNL Sierra software system. This report summarizes the capabilities of the simulation code and the supporting research and development conducted under this LDRD. The main goal of this project was the development of a foundational capability for coupled thermal, hydrological, mechanical, chemical (THMC) simulation of heterogeneous geosystems utilizing massively parallel processing. To solve these complex issues, this project integrated research in numerical mathematics and algorithms for chemically reactive multiphase systems with computer science research in adaptive coupled solution control and framework architecture. This report summarizes and demonstrates the capabilities that were developed together with the supporting research underlying the models. Key accomplishments are: (1) General capability for modeling nonisothermal, multiphase, multicomponent flow in heterogeneous porous geologic materials; (2) General capability to model multiphase reactive transport of species in heterogeneous porous media; (3) Constitutive models for describing real, general geomaterials under multiphase conditions utilizing laboratory data; (4) General capability to couple nonisothermal reactive flow with geomechanics (THMC); (5) Phase behavior thermodynamics for the CO2-H2O-NaCl system. General implementation enables modeling of other fluid mixtures. Adaptive look-up tables enable thermodynamic capability to other simulators; (6) Capability for statistical modeling of heterogeneity in geologic materials; and (7) Simulator utilizes unstructured grids on parallel processing computers.

  11. Thermally activated delayed fluorescence with circularly polarized luminescence characteristics.

    PubMed

    Imagawa, Takuro; Hirata, Shuzo; Totani, Kenro; Watanabe, Toshiyuki; Vacha, Martin

    2015-09-01

    A metal-free aromatic compound with a chiral carbon sandwiched between a donor moiety and an acceptor moiety was designed. Under thermally activated delayed fluorescence, the compound displayed a photoluminescence quantum yield of 26%, and showed circularly polarized luminescence with a dissymmetry factor of 10(-3). PMID:26207648

  12. Active shape control of composite structures under thermal loading

    NASA Astrophysics Data System (ADS)

    Binette, P.; Dano, M.-L.; Gendron, G.

    2009-02-01

    Maintaining the shape of high-precision structures such as space antennas and optical mirrors is still a challenging issue for designers. These structures are subjected to varying temperature conditions which often introduce thermal distortions. The development of smart materials offers great potential to correct the shape and to minimize the surface error. In this study, shape control of a composite structure under thermal loading using piezocomposites is investigated. The composite structure is made of a foam core and two carbon-epoxy face sheets. Macro-fiber composite (MFC™) patches are bonded on one side of the structure. The structure is subjected to a through-the-thickness temperature gradient which induces thermal distortion, essentially in the form of bending. The objective is to apply electric potential to the MFC™ actuators such that the deflection can be minimized. Finite-element analyses are conducted using the commercial software ABAQUS. Experiments are performed to study thermally induced distortion, piezoelectric actuation, and compensation of thermal distortion using MFC™ actuators. Numerical and experimental results are compared. A control loop based on strain measurements is used to actively control the structure. The results show that MFC™ actuators can compensate thermal distortion at all times, and that this is an efficient methodology.

  13. THERMAL IMAGING OF ACTIVE MAGNETIC REGERNERATOR MCE MATERIALS DURING OPERATION

    SciTech Connect

    Shassere, Benjamin; West, David L; Abdelaziz, Omar; Evans III, Boyd Mccutchen

    2012-01-01

    An active magnetic regenerator (AMR) prototype was constructed that incorporates a Gd sheet into the regenerator wall to enable visualization of the system s thermal transients. In this experiment, the thermal conditions inside the AMR are observed under a variety of operating conditions. An infrared (IR) camera is employed to visualize the thermal transients within the AMR. The IR camera is used to visually and quantitatively evaluate the temperature difference and thus giving means to calculate the performance of the system under the various operating conditions. Thermal imaging results are presented for two differing experimental test runs. Real time imaging of the thermal state of the AMR has been conducted while operating the system over a range of conditions. A 1 Tesla twin-coil electromagnet (situated on a C frame base) is used for this experiment such that all components are stationary during testing. A modular, linear reciprocating system has been realized in which the effects of regenerator porosity and utilization factor can be investigated. To evaluate the performance variation in porosity and utilization factor the AMR housing was constructed such that the plate spacing of the Gd sheets may be varied. Each Gd sheet has dimensions of 38 mm wide and 66 mm long with a thickness of 1 mm and the regenerator can hold a maximum of 29 plates with a spacing of 0.25 mm. Quantitative and thermal imaging results are presented for several regenerator configurations.

  14. Experimental performances of a battery thermal management system using a phase change material

    NASA Astrophysics Data System (ADS)

    Hémery, Charles-Victor; Pra, Franck; Robin, Jean-François; Marty, Philippe

    2014-12-01

    Li-ion batteries are leading candidates for mobility because electric vehicles (EV) are an environmentally friendly mean of transport. With age, Li-ion cells show a more resistive behavior leading to extra heat generation. Another kind of problem called thermal runway arises when the cell is too hot, what happens in case of overcharge or short circuit. In order to evaluate the effect of these defects at the whole battery scale, an air-cooled battery module was built and tested, using electrical heaters instead of real cells for safety reasons. A battery thermal management system based on a phase change material is developed in that study. This passive system is coupled with an active liquid cooling system in order to initialize the battery temperature at the melting of the PCM. This initialization, or PCM solidification, can be performed during a charge for example, in other words when the energy from the network is available.

  15. A Novel Silicon Micromachined Integrated MCM Thermal Management System

    NASA Technical Reports Server (NTRS)

    Kazmierczak, M. J.; Henderson, H. T.; Gerner, F. M.

    1997-01-01

    "Micromachining" is a chemical means of etching three-dimensional structures, typically in single- crystalline silicon. These techniques are leading toward what is coming to be referred to as MEMS (Micro Electro Mechanical Systems), where in addition to the ordinary two-dimensional (planar) microelectronics, it is possible to build three-dimensional n-ticromotors, electrically- actuated raicrovalves, hydraulic systems and much more on the same microchip. These techniques become possible because of differential etching rates of various crystallographic planes and materials used for semiconductor n-ticrofabfication. The University of Cincinnati group in collaboration with Karl Baker at NASA Lewis were the first to form micro heat pipes in silicon by the above techniques. Current work now in progress using MEMS technology is now directed towards the development of the next generation in MCM (Multi Chip Module) packaging. Here we propose to develop a complete electronic thermal management system which will allow densifica6on in chip stacking by perhaps two orders of magnitude. Furthermore the proposed technique will allow ordinary conu-nercial integrated chips to be utilized. Basically, the new technique involves etching square holes into a silicon substrate and then inserting and bonding commercially available integrated chips into these holes. For example, over a 100 1/4 in. by 1 /4 in. integrated chips can be placed on a 4 in. by 4 in. silicon substrate to form a Multi-Chip Module (MCM). Placing these MCM's in-line within an integrated rack then allows for three-diniensional stacking. Increased miniaturization of microelectronic circuits will lead to very high local heat fluxes. A high performance thermal management system will be specifically designed to remove the generated energy. More specifically, a compact heat exchanger with milli / microchannels will be developed and tested to remove the heat through the back side of this MCM assembly for moderate and high

  16. Active Thermal Control Experiments for LISA Ground Verification Testing

    NASA Astrophysics Data System (ADS)

    Higuchi, Sei; DeBra, Daniel B.

    2006-11-01

    The primary mission goal of LISA is detecting gravitational waves. LISA uses laser metrology to measure the distance between proof masses in three identical spacecrafts. The total acceleration disturbance to each proof mass is required to be below 3 × 10-15 m/s2√Hz . Optical path length variations on each optical bench must be kept below 40 pm/√Hz over 1 Hz to 0.1 mHz. Thermal variations due to, for example, solar radiation or temperature gradients across the proof mass housing will distort the spacecraft causing changes in the mass attraction and sensor location. We have developed a thermal control system developed for the LISA gravitational reference sensor (GRS) ground verification testing which provides thermal stability better than 1 mK/√Hz to f < 1 mHz and which by extension is suitable for in-flight thermal control for the LISA spacecraft to compensate solar irradiation. Thermally stable environment is very demanded for LISA performance verification. In a lab environment specifications can be met with considerable amount of insulation and thermal mass. For spacecraft, the very limited thermal mass calls for an active control system which can meet disturbance rejection and stability requirements simultaneously in the presence of long time delay. A simple proportional plus integral control law presently provides approximately 1 mK/√Hz of thermal stability for over 80 hours. Continuing development of a model predictive feed-forward algorithm will extend performance to below 1 mK/√Hz at f < 1 mHz and lower.

  17. Increases and fluctuations in thermal activity at Mount Wrangell, Alaska

    SciTech Connect

    Motyka, R.J.

    1983-01-01

    The objectives of this study were to document and interpret changes in thermal activity at two of three craters located on the rim of the ice-filled summit caldera of Mount Wrangell, an active glacier-clad shield volcano in south-central Alaska. The technique of glacier calorimetry was developed, through which changes in the volume of glacier ice in the craters and caldera were measured and related to changes in heat flow. Chemical analysis of gases and acid-thermal waters provided information on the underlying heat source. In 1965, thermal activity began increasing at both the North and West Craters. During the ensuing years, heat flow increased significantly at the North Crater, although in a highly fluctuating manner, while gradually declining at the West Crater. Pulses in heat flow at the North Crater occurred in 1966-68 and 1972-74, with both pulses followed by a four year decline in activity. Increases in heat flow began again in 1978-79 and have continued unabated through the summer of 1983. Over 80% of the 4.4 x 10/sup 7/m/sup 3/ ice volume within the crater in 1966 was melted by 1982, and the meltwaters have drained or evaporated from the crater. The subsequent rapid development of numerous fumaroles, the large dry-gas proportion of SO/sub 2/ (27%), and the inferred presence of gaseous HCl indicate that a shallow degassing magma body is the source of heat driving the thermal system. Seismically induced fracturing above the magma body is hypothesized to explain the initial increases in thermal activity.

  18. Thermal management for heavy vehicles (Class 7-8 trucks)

    SciTech Connect

    Wambsganss, M.W.

    2000-04-03

    Thermal management is a crosscutting technology that has an important effect on fuel economy and emissions, as well as on reliability and safety, of heavy-duty trucks. Trends toward higher-horsepower engines, along with new technologies for reducing emissions, are substantially increasing heat-rejection requirements. For example, exhaust gas recirculation (EGR), which is probably the most popular near-term strategy for reducing NO{sub x} emissions, is expected to add 20 to 50% to coolant heat-rejection requirements. There is also a need to package more cooling in a smaller space without increasing costs. These new demands have created a need for new and innovative technologies and concepts that will require research and development, which, due to its long-term and high-risk nature, would benefit from government funding. This document outlines a research program that was recommended by representatives of truck manufacturers, engine manufacturers, equipment suppliers, universities, and national laboratories. Their input was obtained through personal interviews and a plenary workshop that was sponsored by the DOE Office of Heavy Vehicle Technologies and held at Argonne National Laboratory on October 19--20, 1999. Major research areas that received a strong endorsement by industry and that are appropriate for government funding were identified and included in the following six tasks: (1) Program management/coordination and benefits/cost analyses; (2) Advanced-concept development; (3) Advanced heat exchangers and heat-transfer fluids; (4) Simulation-code development; (5) Sensors and control components development; and (6) Concept/demonstration truck sponsorship.

  19. An active thermal control surfaces experiment. [spacecraft temperature determination

    NASA Technical Reports Server (NTRS)

    Wilkes, D. R.; Brown, M. J.

    1979-01-01

    An active flight experiment is described that has the objectives to determine the effects of the low earth natural environment and the Shuttle induced environment on selected thermal control and optical surfaces. The optical and thermal properties of test samples will be measured in-situ using an integrating sphere reflectrometer and using calorimetric methods. This experiment has been selected for the Long Duration Exposure Facility (LDEF) flight which will be carried to orbit by the NASA Space Shuttle. The LDEF will remain in orbit to be picked up by a later Shuttle mission and returned for postflight evaluation.

  20. Pharmacological activities in thermal proteins: relationships in molecular evolution

    NASA Technical Reports Server (NTRS)

    Fox, S. W.; Hefti, F.; Hartikka, J.; Junard, E.; Przybylski, A. T.; Vaughan, G.

    1987-01-01

    The model of protobiological events that has been presented in these pages has increasing relevance to pharmacological research. The thermal proteins that function as key substances in the proteinoid theory have recently been found to prolong the survival of rat forebrain neurons in culture and to stimulate the growth of neurites. A search for such activity in thermal proteins added to cultures of modern neurons was suggested by the fact that some of the microspheres assembled from proteinoids rich in hydrophobic amino acids themselves generate fibrous outgrowths.

  1. Thermal management of electronic packages for space applications

    SciTech Connect

    Shukla, K.N.; Chacko, M.J.; Mani, L. )

    1990-01-01

    This paper describes the state of the art for thermal mathematical modeling of electronic packages during transient operation. The methods for calculating thermal contact conductance, view factors, and heat transfer coefficients are reviewed, and an algorithm for computer software is provided. Monte Carlo treatment of the data uncertainties is explained. The computer algorithm uniquely incorporates the subroutines for calculating the thermal contact conductance, absorption factor, and statistical representation of the thermal parameters for Monte Carlo analysis.

  2. Assessment of thermal analysis software for the DOE Office of Civilian Radioactive Waste Management

    SciTech Connect

    Williams, P.T.; Graham, R.F.; Lagerberg, G.N.; Chung, T.C.

    1989-07-01

    This assessment uses several recent assessments and the more general code compilations that have been completed to produce a list of 116 codes that can be used for thermal analysis. This list is then compared with criteria prepared especially for the Department of Energy Office of Civilian Radioactive Waste Management (DOE/OCRWM). Based on these criteria, fifteen codes are narrowed to three primary codes and four secondary codes for use by the OCRWM thermal analyst. The analyst is cautioned that since no single code is sufficient for all applications, a code must be selected based upon the predominate heat transfer mode of the problem to be solved, but the codes suggested in this report have been used successfully for a range of OCRWM applications. The report concludes with a series of recommendations for additional work of which the major points include the following: The codes suggested by this report must be benchmarked with the existing US and international problems and validated when possible; An interactive code selection tool could be developed or, perhaps even more useful, a users group could be supported to ensure the proper selection of thermal codes and dissemination of information on the latest version; The status of the 116 codes identified by this report should be verified, and methods for maintaining the still active codes must be established; and special capabilities of each code in phase change, convection and radiation should be improved to better enable the thermal analyst to model OCRWM applications. 37 refs., 3 figs., 12 tabs.

  3. Thermal management of long-length HTS cable systems

    SciTech Connect

    Demko, Jonathan A; Hassenzahl, William V

    2011-01-01

    Projections of electric power production suggest a major shift to renewables, such as wind and solar, which will be in remote locations where massive quantities of power are available. One solution for transmitting this power over long distances to load centers is direct current (dc), high temperature superconducting (HTS) cables. Electric transmission via dc cables promises to be effective because of the low-loss, highcurrent- carrying capability of HTS wire at cryogenic temperatures. However, the thermal management system for the cable must be carefully designed to achieve reliable and energyefficient operation. Here we extend the analysis of a superconducting dc cable concept proposed by the Electric Power Research Institute (EPRI), which has one stream of liquid nitrogen flowing in a cryogenic enclosure that includes the power cable, and a separate return tube for the nitrogen. Refrigeration stations positioned every 10 to 20 km cool both nitrogen streams. Both go and return lines are contained in a single vacuum/cryogenic envelope. Other coolants, including gaseous helium and gaseous hydrogen, could provide potential advantages, though they bring some technical challenges to the operation of long-length HTS dc cable systems. A discussion of the heat produced in superconducting cables and a system to remove the heat are discussed. Also, an analysis of the use of various cryogenic fluids in long-distance HTS power cables is presented.

  4. Analysis and optimization of hybrid electric vehicle thermal management systems

    NASA Astrophysics Data System (ADS)

    Hamut, H. S.; Dincer, I.; Naterer, G. F.

    2014-02-01

    In this study, the thermal management system of a hybrid electric vehicle is optimized using single and multi-objective evolutionary algorithms in order to maximize the exergy efficiency and minimize the cost and environmental impact of the system. The objective functions are defined and decision variables, along with their respective system constraints, are selected for the analysis. In the multi-objective optimization, a Pareto frontier is obtained and a single desirable optimal solution is selected based on LINMAP decision-making process. The corresponding solutions are compared against the exergetic, exergoeconomic and exergoenvironmental single objective optimization results. The results show that the exergy efficiency, total cost rate and environmental impact rate for the baseline system are determined to be 0.29, ¢28 h-1 and 77.3 mPts h-1 respectively. Moreover, based on the exergoeconomic optimization, 14% higher exergy efficiency and 5% lower cost can be achieved, compared to baseline parameters at an expense of a 14% increase in the environmental impact. Based on the exergoenvironmental optimization, a 13% higher exergy efficiency and 5% lower environmental impact can be achieved at the expense of a 27% increase in the total cost.

  5. Thermal management of advanced fuel cell power systems

    NASA Technical Reports Server (NTRS)

    Vanderborgh, N. E.; Hedstrom, J.; Huff, J.

    1990-01-01

    It is shown that fuel cell devices are particularly attractive for the high-efficiency, high-reliability space hardware necessary to support upcoming space missions. These low-temperature hydrogen-oxygen systems necessarily operate with two-phase water. In either PEMFCs (proton exchange membrane fuel cells) or AFCs (alkaline fuel cells), engineering design must be critically focused on both stack temperature control and on the relative humidity control necessary to sustain appropriate conductivity within the ionic conductor. Water must also be removed promptly from the hardware. Present designs for AFC space hardware accomplish thermal management through two coupled cooling loops, both driven by a heat transfer fluid, and involve a recirculation fan to remove water and heat from the stack. There appears to be a certain advantage in using product water for these purposes within PEM hardware, because in that case a single fluid can serve both to control stack temperature, operating simultaneously as a heat transfer medium and through evaporation, and to provide the gas-phase moisture levels necessary to set the ionic conductor at appropriate performance levels. Moreover, the humidification cooling process automatically follows current loads. This design may remove the necessity for recirculation gas fans, thus demonstrating the long-term reliability essential for future space power hardware.

  6. A flow boiling microchannel thermosyphon for fuel cell thermal management

    NASA Astrophysics Data System (ADS)

    Garrity, Patrick Thomas

    To provide a high power density thermal management system for proton exchange membrane (PEM) fuel cell applications, a passively driven thermal management system was assembled to operate in a closed loop two-phase thermosyphon. The system has two major components; a microchannel evaporator plate and a condenser. The microchannel evaporator plate was fabricated with 56 square channels that have a 1 mm x 1 mm cross section and are 115 mm long. Experiments were conducted with a liquid cooled condenser with heat flux as the control variable. Measurements of mass flow rate, temperature field, and pressure drop have been made for the thermosyphon loop. A model is developed to predict the system characteristics such as the temperature and pressure fields, flow rate, flow regime, heat transfer coefficient, and maximum heat flux. When the system is subjected to a heat load that exceeds the maximum heat flux, an unstable flow regime is observed that causes flow reversal and eventual dryout near the evaporator plate wall. This undesirable phenomenon is modeled based on a quasi-steady state assumption, and the model is capable of predicting the heat flux at the onset of instability for quasi-steady two-phase flow. Another focus of this work is the performance of the condenser portion of the loop, which will be air cooled in practice. The aim is to reduce air side thermal resistance and increase the condenser performance, which is accomplished with extended surfaces. A testing facility is assembled to observe the air side heat transfer performance of three aluminum foam samples and three modified carbon foam samples, used as extended surfaces. The aluminum foam samples have a bulk density of 216 kilograms per cubic meter with pore sizes of 0.5, 1, and 2 mm. The modified carbon foam samples have bulk densities of 284, 317, and 400 kilograms per cubic meter and machined flow passages of 3.2 mm. in diameter. Each sample is observed under forced convection with air velocity as the

  7. Electrochemical-thermal modeling and microscale phase change for passive internal thermal management of lithium ion batteries.

    SciTech Connect

    Fuller, Thomas F.; Bandhauer, Todd; Garimella, Srinivas

    2012-01-01

    A fully coupled electrochemical and thermal model for lithium-ion batteries is developed to investigate the impact of different thermal management strategies on battery performance. In contrast to previous modeling efforts focused either exclusively on particle electrochemistry on the one hand or overall vehicle simulations on the other, the present work predicts local electrochemical reaction rates using temperature-dependent data on commercially available batteries designed for high rates (C/LiFePO{sub 4}) in a computationally efficient manner. Simulation results show that conventional external cooling systems for these batteries, which have a low composite thermal conductivity ({approx}1 W/m-K), cause either large temperature rises or internal temperature gradients. Thus, a novel, passive internal cooling system that uses heat removal through liquid-vapor phase change is developed. Although there have been prior investigations of phase change at the microscales, fluid flow at the conditions expected here is not well understood. A first-principles based cooling system performance model is developed and validated experimentally, and is integrated into the coupled electrochemical-thermal model for assessment of performance improvement relative to conventional thermal management strategies. The proposed cooling system passively removes heat almost isothermally with negligible thermal resistances between the heat source and cooling fluid. Thus, the minimization of peak temperatures and gradients within batteries allow increased power and energy densities unencumbered by thermal limitations.

  8. Evaluation of active thermal control options for Space Station

    NASA Technical Reports Server (NTRS)

    Schuster, J. R.; Gruszczynski, M. J.; Owen, J. W.

    1986-01-01

    An analysis of various Space Station (MSS) active thermal control systems options under consideration because of their potential low weight, efficiency and reliability is reported. The study addressed ordinary and diode-action body mounted radiators, thermal storage, the area and pumping power requirements for single-phase cooling of cold plates, and single-phase and two-phase active cooling loops. The base configuration considered was a core MSS formed by four habitable modules on which are mounted heat pipe radiators articulated to be always edge-on to the sun. A simulation was performed which accounted for the available heat sinks, several thermal loads and the heat rejection capability. No benefits were found with diode-action radiators if the solar absorption is 0.1 or less, although diode-action heat pipes will maintain a higher level of performance in the presence of coating degradation. Thermal storage becomes important only with radiator coating degradation. Water can be up to three times as efficient as Freon as a heat transfer medium. Finally, single-phase cooling offers a lower system mass than two-phase cooling if varying temperature heat loads can be accommodated.

  9. An Environmental Management Model of Thermal Waters in Entre Ríos Province, Argentina

    NASA Astrophysics Data System (ADS)

    Pablo, Mársico Daniel; Luís, Díaz Eduardo; Ivana, Zecca; Oscar, Dallacosta; Antonio, Paz-González

    2015-04-01

    Deep exploratory drillings, i.e. those with more than 500 meters depth, have been performed in the Entre Ríos province, Argentina, in order to ascertain the presence of thermal water. Drilling began in 1994, and until now there have been 18 polls with very variable results in terms of mineralization, resource flow, and temperature. The aim of this study was to present a management model, which should allow operators of thermal complexes to further develop procedures for safeguarding the biodiversity of the ecosystems involved, both during exploration and exploitation activities. The environmental management Plan proposed is constituted by a set of technical procedures that are formulated and should be performed during the stages of exploration and exploitation of the resource, and consists of: environmental monitoring, environmental audit, public information and contingency programs. This Plan describes the measures and proposals aimed at protecting environmental quality in the area of influence of a thermal complex project, ensuring that its execution remains environmentally responsibly, and allowing implementation of specific actions to prevent or correct environmental impacts, as predicted in the evaluation of the Environmental Program. The audit of environmental impact includes and takes into account natural factors, such as water, soil, atmosphere, flora and fauna, and also cultural factors. The technical audit Plan was prepared in order to get a systematic structure and organization of the verification process, and also with regard to document the degree of implementation of the proposed mitigation measures. Finally, an environmental contingency program was implemented, and its objective was to consider the safeguarding of life and its natural environment. Thus, a guide has been developed with the main actions to be taken on a contingency, since forecast increases the efficiency of the response. The methodology developed here was adopted as the procedure

  10. Automotive Underhood Thermal Management Analysis Using 3-D Coupled Thermal-Hydrodynamic Computer Models: Thermal Radiation Modeling

    SciTech Connect

    Pannala, S; D'Azevedo, E; Zacharia, T

    2002-02-26

    The goal of the radiation modeling effort was to develop and implement a radiation algorithm that is fast and accurate for the underhood environment. As part of this CRADA, a net-radiation model was chosen to simulate radiative heat transfer in an underhood of a car. The assumptions (diffuse-gray and uniform radiative properties in each element) reduce the problem tremendously and all the view factors for radiation thermal calculations can be calculated once and for all at the beginning of the simulation. The cost for online integration of heat exchanges due to radiation is found to be less than 15% of the baseline CHAD code and thus very manageable. The off-line view factor calculation is constructed to be very modular and has been completely integrated to read CHAD grid files and the output from this code can be read into the latest version of CHAD. Further integration has to be performed to accomplish the same with STAR-CD. The main outcome of this effort is to obtain a highly scalable and portable simulation capability to model view factors for underhood environment (for e.g. a view factor calculation which took 14 hours on a single processor only took 14 minutes on 64 processors). The code has also been validated using a simple test case where analytical solutions are available. This simulation capability gives underhood designers in the automotive companies the ability to account for thermal radiation - which usually is critical in the underhood environment and also turns out to be one of the most computationally expensive components of underhood simulations. This report starts off with the original work plan as elucidated in the proposal in section B. This is followed by Technical work plan to accomplish the goals of the project in section C. In section D, background to the current work is provided with references to the previous efforts this project leverages on. The results are discussed in section 1E. This report ends with conclusions and future scope of

  11. NREL Works to Increase Electric Vehicle Efficiency Through Enhanced Thermal Management (Fact Sheet)

    SciTech Connect

    Not Available

    2014-06-01

    Researchers at NREL are providing new insight into how heating and cooling systems affect the distance that electric vehicles can travel on a single charge. Electric vehicle range can be reduced by as much as 68% per charge because of climate-control demands. NREL engineers are investigating opportunities to change this dynamic and increase driving range by improving vehicle thermal management. NREL experts are collaborating with automotive industry partners to investigate promising thermal management technologies and strategies, including zone-based cabin temperature controls, advanced heating and air conditioning controls, seat-based climate controls, vehicle thermal preconditioning, and thermal load reduction technologies.

  12. YoeB toxin is activated during thermal stress.

    PubMed

    Janssen, Brian D; Garza-Sánchez, Fernando; Hayes, Christopher S

    2015-08-01

    Type II toxin-antitoxin (TA) modules are thought to mediate stress-responses by temporarily suppressing protein synthesis while cells redirect transcription to adapt to environmental change. Here, we show that YoeB, a ribosome-dependent mRNase toxin, is activated in Escherichia coli cells grown at elevated temperatures. YoeB activation is dependent on Lon protease, suggesting that thermal stress promotes increased degradation of the YefM antitoxin. Though YefM is efficiently degraded in response to Lon overproduction, we find that Lon antigen levels do not increase during heat shock, indicating that another mechanism accounts for temperature-induced YefM proteolysis. These observations suggest that YefM/YoeB functions in adaptation to temperature stress. However, this response is distinct from previously described models of TA function. First, YoeB mRNase activity is maintained over several hours of culture at 42°C, indicating that thermal activation is not transient. Moreover, heat-activated YoeB does not induce growth arrest nor does it suppress global protein synthesis. In fact, E. coli cells proliferate more rapidly at elevated temperatures and instantaneously accelerate their growth rate in response to acute heat shock. We propose that heat-activated YoeB may serve a quality control function, facilitating the recycling of stalled translation complexes through ribosome rescue pathways. PMID:26147890

  13. YoeB toxin is activated during thermal stress

    PubMed Central

    Janssen, Brian D; Garza-Sánchez, Fernando; Hayes, Christopher S

    2015-01-01

    Type II toxin-antitoxin (TA) modules are thought to mediate stress-responses by temporarily suppressing protein synthesis while cells redirect transcription to adapt to environmental change. Here, we show that YoeB, a ribosome-dependent mRNase toxin, is activated in Escherichia coli cells grown at elevated temperatures. YoeB activation is dependent on Lon protease, suggesting that thermal stress promotes increased degradation of the YefM antitoxin. Though YefM is efficiently degraded in response to Lon overproduction, we find that Lon antigen levels do not increase during heat shock, indicating that another mechanism accounts for temperature-induced YefM proteolysis. These observations suggest that YefM/YoeB functions in adaptation to temperature stress. However, this response is distinct from previously described models of TA function. First, YoeB mRNase activity is maintained over several hours of culture at 42°C, indicating that thermal activation is not transient. Moreover, heat-activated YoeB does not induce growth arrest nor does it suppress global protein synthesis. In fact, E. coli cells proliferate more rapidly at elevated temperatures and instantaneously accelerate their growth rate in response to acute heat shock. We propose that heat-activated YoeB may serve a quality control function, facilitating the recycling of stalled translation complexes through ribosome rescue pathways. PMID:26147890

  14. Preoptic activation and connectivity during thermal sweating in humans

    PubMed Central

    Farrell, Michael J; Trevaks, David; McAllen, Robin M

    2014-01-01

    Animal studies have identified the preoptic area as the key thermoregulatory region of the brain but no comparable information exists in humans. We used fMRI to study the preoptic area of human volunteers. Subjects lay in a 3T MRI scanner and were subjected to whole body heating by a water-perfused suit, to a level that resulted in a low rate of discrete sweating events (measured by finger skin resistance). Control scans were taken under thermoneutral conditions in another group. A discrete cluster of voxels in the preoptic area showed activity that was significantly correlated with thermal sweating events. We then used this cluster as a seed to investigate whether other brain areas had activity correlated with its signal, and whether that correlation depended on thermal state. Several brain regions including the dorsal cingulate cortex, anterior insula and midbrain showed ongoing activity that was correlated with that of the preoptic seed more strongly during heating than during thermoneutrality. These data provide the first imaging evidence for a thermoregulatory role of the human preoptic area. They further suggest that during thermal stress, the preoptic area communicates to several other brain regions with known relevance to the control of autonomic effectors.

  15. The Thermal Activity of Normal and Malignant Tissues

    PubMed Central

    Cheng, Li-Yao

    1998-01-01

    The usefulness of metabolic heat measurements in quantifying the response of a solid tumour to anticancer treatment was evaluated. The heat production characteristic of malignant tissues, as measured from human stomach, breast and liver cancer samples, was observed to be inconsistent, and its value could be higher or lower than that of its normal tissue of origin. The various thermal activity responses of an experimental rat hepatoma to hepatic artery ligation, cryotherapy, intra-arterial (i.a) Adriamycin (2.4 mg/ kg), i.a. Norcantharidin (0.5 mg/kg) were next studied. The tumour/liver (T/L) ratio of untreated tumour-bearing rats was 0.83 but this fell to a minimum at 24 h in both the hepatic artery ligation and the cryosurgery groups. In these two groups marked fluctuations in the heat production of normal liver occurred with poor recovery of the T/ L ratio even at 2--3 weeks. In the Adriamycin group, the T/L ratio dropped to a minimum at 5 days, and in the Norcantharidin group, at 3 days. Minimal disturbances in the thermal activity of liver tissue occured in these two chemotherapy groups and the T/L ratio recovered by 3 weeks. Norcantharidin appeared as efficacious as Adriamycin in the treatment of hepatoma when evaluated in terms of thermal activity. PMID:9893237

  16. Thermal management in heavy vehicles : a review identifying issues and research requirements.

    SciTech Connect

    Wambsganss, M. W.

    1999-01-15

    Thermal management in heavy vehicles is cross-cutting because it directly or indirectly affects engine performance, fuel economy, safety and reliability, engine/component life, driver comfort, materials selection, emissions, maintenance, and aerodynamics. It follows that thermal management is critical to the design of large (class 6-8) trucks, especially in optimizing for energy efficiency and emissions reduction. Heat rejection requirements are expected to increase, and it is industry's goal to develop new, innovative, high-performance cooling systems that occupy less space and are lightweight and cost-competitive. The state of the art in heavy vehicle thermal management is reviewed, and issues and research areas are identified.

  17. Thermally activated breakdown in a simple polymer model.

    PubMed

    Fugmann, S; Sokolov, I M

    2010-03-01

    We consider the thermally activated fragmentation of a homopolymer chain. In our simple model the dynamics of the intact chain is a Rouse one until a bond breaks and bond breakdown is considered as a first passage problem over a barrier to an absorbing boundary. Using the framework of the Wilemski-Fixman approximation we calculate activation times of individual bonds for free and grafted chains. We show that these times crucially depend on the length of the chain and the location of the bond yielding a minimum at the free chain ends. Theoretical findings are qualitatively confirmed by Brownian dynamics simulations. PMID:20365762

  18. United States Department of Energy Thermally Activated Heat Pump Program

    SciTech Connect

    Fiskum, R.J.; Adcock, P.W.; DeVault, R.C.

    1996-06-01

    The US Department of Energy (DOE) is working with partners from the gas heating and cooling industry to improve energy efficiency using advance absorption technologies, to eliminate chlorofluorocarbons (CFCs) and hydrochlorofluorocarbons (HCFCs), to reduce global warming through more efficient combustion of natural gas, and to impact electric peak demand of air conditioning. To assist industry in developing these gas heating and cooling absorption technologies, the US DOE sponsors the Thermally Activated Heat Pump Program. It is divided into five key activities, addressing residential gas absorption heat pumps, large commercial chillers, advanced absorption fluids, computer-aided design, and advanced ``Hi-Cool`` heat pumps.

  19. Measuring thermal budgets of active volcanoes by satellite remote sensing

    NASA Technical Reports Server (NTRS)

    Glaze, L.; Francis, P. W.; Rothery, D. A.

    1989-01-01

    Thematic Mapper measurements of the total radiant energy flux Q at Lascar volcano in north Chile for December 1984 are reported. The results are consistent with the earlier suggestion that a lava lake is the source of a reported thermal budget anomaly, and with values for 1985-1986 that are much lower, suggesting that fumarolic activity was then a more likely heat source. The results show that satellite remote sensing may be used to monitor the activity of a volcano quantitatively, in a way not possible by conventional ground studies, and may provide a method for predicting eruptions.

  20. An Integrated Approach to Thermal Management of International Space Station Logistics Flights, Improving the Efficiency

    NASA Technical Reports Server (NTRS)

    Holladay, Jon; Day, Greg; Roberts, Barry; Leahy, Frank

    2003-01-01

    The efficiency of re-useable aerospace systems requires a focus on the total operations process rather than just orbital performance. For the Multi-Purpose Logistics Module this activity included special attention to terrestrial conditions both pre-launch and post-landing and how they inter-relate to the mission profile. Several of the efficiencies implemented for the MPLM Mission Engineering were NASA firsts and all served to improve the overall operations activities. This paper will provide an explanation of how various issues were addressed and the resulting solutions. Topics range from statistical analysis of over 30 years of atmospheric data at the launch and landing site to a new approach for operations with the Shuttle Carrier Aircraft. In each situation the goal was to "tune" the thermal management of the overall flight system for minimizing requirement risk while optimizing power and energy performance.

  1. Thermal constraints on activity scheduling and habitat choice in baboons.

    PubMed

    Hill, Russell A

    2006-02-01

    The importance of thermoregulation as a constraint on behavior has received comparatively little attention in relation to other ecological factors. Despite this, a number of studies suggested that high temperature may represent an important ecological constraint. This paper examines the impact of temperature on activity scheduling in a troop of chacma baboons (Papio hamadryas ursinus) at De Hoop Nature Reserve, South Africa. Once the daily, seasonal, and individual effects were controlled for, the "perceived environmental temperature" (PET), which accounts for the relative contributions of solar radiation, wind speed, and humidity on shade temperature, was a significant constraint on behavior. With high PET, feeding declines, and there is an increase in grooming and particularly resting behavior. Baboons thus engage in more sedentary behaviors as temperature increases, with significantly higher levels of resting and grooming when temperature exceeds the approximate thermal neutral zone for baboons. Seeking shade is an important behavioral response to thermal stress, and PET was a significant determinant of whether an animal was in shade while engaged in either resting or grooming behavior. Furthermore, the proportion of time spent in shade increased across air temperatures that were below, within, and above the thermal neutral zone for baboons. Finally, since resting and grooming are conducted preferentially in certain habitat types, thermoregulatory considerations also impact on patterns of habitat choice and day-journey routes. This suggests that the thermal environment is an ecological variable that should be given greater consideration in future studies of primate behavior. PMID:16323181

  2. Chronic Fatigue Syndrome (CFS): Managing Activities and Exercise

    MedlinePlus

    ... Fatigue Syndrome (CFS) Share Compartir Managing Activities and Exercise On this Page Avoiding Extremes Developing an Activity ... recent manageable level of activity. Strength and Conditioning Exercises Strength and conditioning exercises are an important component ...

  3. Correcting Thermal Deformations in an Active Composite Reflector

    NASA Technical Reports Server (NTRS)

    Bradford, Samuel C.; Agnes, Gregory S.; Wilkie, William K.

    2011-01-01

    Large, high-precision composite reflectors for future space missions are costly to manufacture, and heavy. An active composite reflector capable of adjusting shape in situ to maintain required tolerances can be lighter and cheaper to manufacture. An active composite reflector testbed was developed that uses an array of piezoelectric composite actuators embedded in the back face sheet of a 0.8-m reflector panel. Each individually addressable actuator can be commanded from 500 to +1,500 V, and the flatness of the panel can be controlled to tolerances of 100 nm. Measuring the surface flatness at this resolution required the use of a speckle holography interferometer system in the Precision Environmental Test Enclosure (PETE) at JPL. The existing testbed combines the PETE for test environment stability, the speckle holography system for measuring out-of-plane deformations, the active panel including an array of individually addressable actuators, a FLIR thermal camera to measure thermal profiles across the reflector, and a heat source. Use of an array of flat piezoelectric actuators to correct thermal deformations is a promising new application for these actuators, as is the use of this actuator technology for surface flatness and wavefront control. An isogrid of these actuators is moving one step closer to a fully active face sheet, with the significant advantage of ease in manufacturing. No extensive rib structure or other actuation backing structure is required, as these actuators can be applied directly to an easy-to-manufacture flat surface. Any mission with a surface flatness requirement for a panel or reflector structure could adopt this actuator array concept to create lighter structures and enable improved performance on orbit. The thermal environment on orbit tends to include variations in temperature during shadowing or changes in angle. Because of this, a purely passive system is not an effective way to maintain flatness at the scale of microns over several

  4. Thermal management of space-based, high-power solid-state RF amplifiers. Final report

    SciTech Connect

    Rose, M.F.; Chow, L.C.; Johnson, J.H.

    1990-08-01

    The advanced weapons concepts envisioned by the SDIO employed a wide array of highly energetic devices, which due to inefficiencies, generate large quantities of waste heat. Power and thermal management are integrally related. In the vacuum of space, disposing of waste energy is a major problem which can contribute as much as 50% to the overall spacecraft mass and volume. The problem becomes more acute as the temperature at which the energy must be rejected is lowered. In an earlier study, thermal management issues associated with megawatt class RF microwave tubes were explored to determine if there were simple, approximately mass neutral schemes which might be adapted to dispose of the waste energy generated within a tube collector operating in space. The assumptions for that study were: (1) Tubes were in the megawatt class-70% efficient for single simple collector and 90% efficient for depressed collectors, (2) On-board, super critical hydrogen was available at a pressure of 35 bars and a temperature of 35 K. (3) The largest single event run time was 500 seconds. (4) The device would be dormant for long periods of time, be required to become active in tens of seconds followed by long periods of dormancy. (5) The only allowable effluent is hydrogen. (6) System impact must be minimal.

  5. Final Report: Development of a Thermal and Water Management System for PEM Fuel Cell

    SciTech Connect

    Zia Mirza, Program Manager

    2011-12-06

    This final program report is prepared to provide the status of program activities performed over the period of 9 years to develop a thermal and water management (TWM) system for an 80-kW PEM fuel cell power system. The technical information and data collected during this period are presented in chronological order by each calendar year. Balance of plant (BOP) components of a PEM fuel cell automotive system represents a significant portion of total cost based on the 2008 study by TIAX LLC, Cambridge, MA. The objectives of this TWM program were two-fold. The first objective was to develop an advanced cooling system (efficient radiator) to meet the fuel cell cooling requirements. The heat generated by the fuel cell stack is a low-quality heat (small difference between fuel cell stack operating temperature and ambient air temperature) that needs to be dissipated to the ambient air. To minimize size, weight, and cost of the radiator, advanced fin configurations were evaluated. The second objective was to evaluate air humidification systems which can meet the fuel cell stack inlet air humidity requirements. The moisture from the fuel cell outlet air is transferred to inlet air, thus eliminating the need for an outside water source. Two types of humidification devices were down-selected: one based on membrane and the other based on rotating enthalpy wheel. The sub-scale units for both of these devices have been successfully tested by the suppliers. This project addresses System Thermal and Water Management.

  6. Note: A simple model for thermal management in solenoids

    SciTech Connect

    McIntosh, E. M. Ellis, J.

    2013-11-15

    We describe a model of the dynamical temperature evolution in a solenoid winding. A simple finite element analysis is calibrated by accurately measuring the thermally induced resistance change of the solenoid, thus obviating the need for accurate knowledge of the mean thermal conductivity of the windings. The model predicts quasi thermal runaway for relatively modest current increases from the normal operating conditions. We demonstrate the application of this model to determine the maximum current that can be safely applied to solenoids used for helium spin-echo measurements.

  7. Printable, flexible and stretchable diamond for thermal management

    DOEpatents

    Rogers, John A; Kim, Tae Ho; Choi, Won Mook; Kim, Dae Hyeong; Meitl, Matthew; Menard, Etienne; Carlisle, John

    2013-06-25

    Various heat-sinked components and methods of making heat-sinked components are disclosed where diamond in thermal contact with one or more heat-generating components are capable of dissipating heat, thereby providing thermally-regulated components. Thermally conductive diamond is provided in patterns capable of providing efficient and maximum heat transfer away from components that may be susceptible to damage by elevated temperatures. The devices and methods are used to cool flexible electronics, integrated circuits and other complex electronics that tend to generate significant heat. Also provided are methods of making printable diamond patterns that can be used in a range of devices and device components.

  8. Optically active surfaces formed by ion implantation and thermal treatment

    SciTech Connect

    Gea, L.A.; Boatner, L.A.; Evans, H.M.; Zuhr, R.

    1996-08-01

    Embedded VO{sub 2} precipitates have been formed in single-crystal sapphire by the ion co-implantation of vanadium and oxygen and subsequent thermal annealing. The embedded VO{sub 2} particles have been shown to exhibit an optical switching behavior that is comparable to that of continuous thin films. In this work, the mechanisms of formation of these optically active particles are investigated. It is shown that precipitation of the vanadium dioxide phase is favored when the thermal treatment is performed on an ion-damaged but still crystalline (rather than amorphized) Al{sub 2}O{sub 3} substrate. The best optical switching behavior is observed in this case, and this behavior is apparently correlated with a more-favorable dispersion of VO{sub 2} small particles inside the matrix.

  9. Thermally activated retainer means utilizing shape memory alloy

    NASA Technical Reports Server (NTRS)

    Grimaldi, Margaret E. (Inventor); Hartz, Leslie S. (Inventor)

    1993-01-01

    A retainer member suitable for retaining a gap filler placed in gaps between adjacent tile members is presented. One edge of the retainer member may be attached to the gap filler and another edge may be provided with a plurality of tab members which in an intermediate position do not interfere with placement or removal of the gap filler between tile members. The retainer member may be fabricated from a shape memory alloy which when heated to a specified memory temperature will thermally activate the tab members to predetermined memory positions engaging the tile members to retain the gap filler in the gap. This invention has particular application to the thermal tiles on space vehicles such as the Space Shuttle Orbiter.

  10. Bonding and Integration of C-C Composite to Cu-Clad-Molybdenum for Thermal Management Applications

    NASA Technical Reports Server (NTRS)

    Asthana, R.; Singh, M.; Shpargel, T.P.

    2008-01-01

    Two- and three-dimensional carbon-carbon composites with either resin-derived matrix or CVI matrix were joined to Cu-clad-Mo using active Ag-Cu braze alloys for thermal management applications. The joint microstructure and composition were examined using Field-Emission Scanning Electron Microscopy and Energy-Dispersive Spectroscopy, and the joint hardness was characterized using the Knoop microhardness testing. Observations on the infiltration of the composite with molten braze, dissolution of metal substrate, and solute segregation at the C-C surface have been discussed. The thermal response of the integrated assembly is also briefly discussed.

  11. Managerial activities and skills of nurse managers: an exploratory study.

    PubMed

    Lin, Li-Min; Wu, Jen-Her; White, Louis P

    2005-01-01

    In this study, the authors used the activity competency model (Wu, Chen, and Lin 2004) to investigate the perceived importance of managerial activities and skills required of three levels of nurse managers. They identify the portfolio of the management activities and the needed skills at each management level. The results of this study provide guidelines for management development programs, training, and career planning for nurse managers, and can also serve as guidelines for recruiting and selecting effective nurse managers. PMID:16190515

  12. A system for measuring thermal activation energy levels in silicon by thermally stimulated capacitance

    NASA Technical Reports Server (NTRS)

    Cockrum, R. H.

    1982-01-01

    One method being used to determine energy level(s) and electrical activity of impurities in silicon is described. The method is called capacitance transient spectroscopy (CTS). It can be classified into three basic categories: the thermally stimulated capacitance method, the voltage-stimulated capacitance method, and the light-stimulated capacitance method; the first two categories are discussed. From the total change in capacitance and the time constant of the capacitance response, emission rates, energy levels, and trap concentrations can be determined. A major advantage of using CTS is its ability to detect the presence of electrically active impurities that are invisible to other techniques, such as Zeeman effect atomic absorption, and the ability to detect more than one electrically active impurity in a sample. Examples of detection of majority and minority carrier traps from gold donor and acceptor centers in silicon using the capacitance transient spectrometer are given to illustrate the method and its sensitivity.

  13. Electric Motor Thermal Management for Electric Traction Drives (Presentation)

    SciTech Connect

    Bennion, K.; Cousineau, J.; Moreno, G.

    2014-09-01

    Thermal constraints place significant limitations on how electric motors ultimately perform. Finite element analysis and computational fluid dynamics modeling approaches are being increasingly utilized in the design and analysis of electric motors. As the models become more sophisticated, it is important to have detailed and accurate knowledge of material thermal properties and convective heat transfer coefficients. In this work, the thermal properties and inter-lamination thermal contact resistances were measured for different stator lamination materials. Also, convective heat transfer coefficients of automatic transmission fluid (ATF) jets were measured to better understand the heat transfer of ATF impinging on motor copper windings. Experiments were carried out at various ATF temperatures and jet velocities to quantify the influence of these parameters on heat transfer coefficients.

  14. Advanced thermal energy management: A thermal test bed and heat pipe simulation

    NASA Technical Reports Server (NTRS)

    Barile, Ronald G.

    1986-01-01

    Work initiated on a common-module thermal test simulation was continued, and a second project on heat pipe simulation was begun. The test bed, constructed from surplus Skylab equipment, was modeled and solved for various thermal load and flow conditions. Low thermal load caused the radiator fluid, Coolanol 25, to thicken due to its temperature avoided by using a regenerator-heat-exchanger. Other possible solutions modeled include a radiator heater and shunting heat from the central thermal bus to the radiator. Also, module air temperature can become excessive with high avionics load. A second preoject concerning advanced heat pipe concepts was initiated. A program was written which calculates fluid physical properties, liquid and vapor pressure in the evaporator and condenser, fluid flow rates, and thermal flux. The program is directed to evaluating newer heat pipe wicks and geometries, especially water in an artery surrounded by six vapor channels. Effects of temperature, groove and slot dimensions, and wick properties are reported.

  15. Lighting system with thermal management system having point contact synthetic jets

    DOEpatents

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Sharma, Rajdeep

    2013-12-10

    Lighting system having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  16. Lighting system with thermal management system having point contact synthetic jets

    DOEpatents

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Sharma, Rajdeep

    2016-08-23

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  17. Lighting system with thermal management system having point contact synthetic jets

    DOEpatents

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr, Charles Franklin; Sharma, Rajdeep

    2016-08-30

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  18. Analysis of DOE international environmental management activities

    SciTech Connect

    Ragaini, R.C.

    1995-09-01

    The Department of Energy`s (DOE) Strategic Plan (April 1994) states that DOE`s long-term vision includes world leadership in environmental restoration and waste management activities. The activities of the DOE Office of Environmental Management (EM) can play a key role in DOE`s goals of maintaining U.S. global competitiveness and ensuring the continuation of a world class science and technology community. DOE`s interest in attaining these goals stems partly from its participation in organizations like the Trade Policy Coordinating Committee (TPCC), with its National Environmental Export Promotion Strategy, which seeks to strengthen U.S. competitiveness and the building of public-private partnerships as part of U.S. industrial policy. The International Interactions Field Office task will build a communication network which will facilitate the efficient and effective communication between DOE Headquarters, Field Offices, and contractors. Under this network, Headquarters will provide the Field Offices with information on the Administration`s policies and activities (such as the DOE Strategic Plan), interagency activities, as well as relevant information from other field offices. Lawrence Livermore National Laboratory (LLNL) will, in turn, provide Headquarters with information on various international activities which, when appropriate, will be included in reports to groups like the TPCC and the EM Focus Areas. This task provides for the collection, review, and analysis of information on the more significant international environmental restoration and waste management initiatives and activities which have been used or are being considered at LLNL. Information gathering will focus on efforts and accomplishments in meeting the challenges of providing timely and cost effective cleanup of its environmentally damaged sites and facilities, especially through international technical exchanges and/or the implementation of foreign-development technologies.

  19. Smart Building: Decision Making Architecture for Thermal Energy Management

    PubMed Central

    Hernández Uribe, Oscar; San Martin, Juan Pablo; Garcia-Alegre, María C.; Santos, Matilde; Guinea, Domingo

    2015-01-01

    Smart applications of the Internet of Things are improving the performance of buildings, reducing energy demand. Local and smart networks, soft computing methodologies, machine intelligence algorithms and pervasive sensors are some of the basics of energy optimization strategies developed for the benefit of environmental sustainability and user comfort. This work presents a distributed sensor-processor-communication decision-making architecture to improve the acquisition, storage and transfer of thermal energy in buildings. The developed system is implemented in a near Zero-Energy Building (nZEB) prototype equipped with a built-in thermal solar collector, where optical properties are analysed; a low enthalpy geothermal accumulation system, segmented in different temperature zones; and an envelope that includes a dynamic thermal barrier. An intelligent control of this dynamic thermal barrier is applied to reduce the thermal energy demand (heating and cooling) caused by daily and seasonal weather variations. Simulations and experimental results are presented to highlight the nZEB thermal energy reduction. PMID:26528978

  20. Smart Building: Decision Making Architecture for Thermal Energy Management.

    PubMed

    Uribe, Oscar Hernández; Martin, Juan Pablo San; Garcia-Alegre, María C; Santos, Matilde; Guinea, Domingo

    2015-01-01

    Smart applications of the Internet of Things are improving the performance of buildings, reducing energy demand. Local and smart networks, soft computing methodologies, machine intelligence algorithms and pervasive sensors are some of the basics of energy optimization strategies developed for the benefit of environmental sustainability and user comfort. This work presents a distributed sensor-processor-communication decision-making architecture to improve the acquisition, storage and transfer of thermal energy in buildings. The developed system is implemented in a near Zero-Energy Building (nZEB) prototype equipped with a built-in thermal solar collector, where optical properties are analysed; a low enthalpy geothermal accumulation system, segmented in different temperature zones; and an envelope that includes a dynamic thermal barrier. An intelligent control of this dynamic thermal barrier is applied to reduce the thermal energy demand (heating and cooling) caused by daily and seasonal weather variations. Simulations and experimental results are presented to highlight the nZEB thermal energy reduction. PMID:26528978

  1. Evaluation of thermal and moisture management properties on knitted fabrics and comparison with a physiological model in warm conditions.

    PubMed

    Bedek, Gauthier; Salaün, Fabien; Martinkovska, Zuzana; Devaux, Eric; Dupont, Daniel

    2011-11-01

    This study reports on an experimental investigation of physical properties on the textile thermal comfort. Textile properties, such as thickness, relative porosity, air permeability, moisture regain, thermal conductivity, drying time and water-vapour transmission rate have been considered and correlated to the thermal and vapour resistance, permeability index, thermal effusivity and moisture management capability in order to determine the overall comfort performance of underwear fabrics. The results suggested that the fibre type, together with moisture regain and knitted structure characteristics appeared to affect some comfort-related properties of the fabrics. Additionally, thermal sensations, temperature and skin wetness predicted by Caseto® software for three distinct activity levels were investigated. Results show that the data obtained from this model in transient state are correlated to the thermal conductivity for the temperature and to Ret, moisture regain and drying time for the skin wetness. This provides potential information to determine the end uses of these fabrics according to the selected activity level. PMID:21277564

  2. Thermally activated depinning motion of contact lines in pseudopartial wetting.

    PubMed

    Du, Lingguo; Bodiguel, Hugues; Colin, Annie

    2014-07-01

    We investigate pressure-driven motion of liquid-liquid menisci in circular tubes, for systems in pseudopartial wetting conditions. The originality of this type of wetting lies in the coexistence of a macroscopic contact angle with a wetting liquid film covering the solid surface. Focusing on small capillary numbers, we report observations of an apparent contact angle hysteresis at first sight similar to the standard partial wetting case. However, this apparent hysteresis exhibits original features. We observe very long transient regimes before steady state, up to several hundreds of seconds. Furthermore, in steady state, the velocities are nonzero, meaning that the contact line is not strongly pinned to the surface defects, but are very small. The velocity of the contact line tends to vanish near the equilibrium contact angle. These observations are consistent with the thermally activated depinning theory that has been proposed to describe partial wetting systems on disordered substrates and suggest that a single physical mechanism controls both the hysteresis (or the pinning) and the motion of the contact line. The proposed analysis leads to the conclusion that the depinning activated energy is lower with pseudopartial wetting systems than with partial wetting ones, allowing the direct observation of the thermally activated motion of the contact line. PMID:25122310

  3. Thermal Performance of Orion Active Thermal Control System With Seven-Panel Reduced-Curvature Radiator

    NASA Technical Reports Server (NTRS)

    Wang, Xiao-Yen J.; Yuko, James R.

    2010-01-01

    The active thermal control system (ATCS) of the crew exploration vehicle (Orion) uses radiator panels with fluid loops as the primary system to reject heat from spacecraft. The Lockheed Martin (LM) baseline Orion ATCS uses eight-panel radiator coated with silver Teflon coating (STC) for International Space Station (ISS) missions, and uses seven-panel radiator coated with AZ 93 white paint for lunar missions. As an option to increase the radiator area with minimal impact on other component locations and interfaces, the reduced-curvature (RC) radiator concept was introduced and investigated here for the thermal perspective. Each RC radiator panel has 15 percent more area than each Lockheed Martin (LM) baseline radiator panel. The objective was to determine if the RC seven-panel radiator concept could be used in the ATCS for both ISS and lunar missions. Three radiator configurations the LM baseline, an RC seven-panel radiator with STC, and an RC seven-panel radiator with AZ 93 coating were considered in the ATCS for ISS missions. Two radiator configurations the LM baseline and an RC seven-panel radiator with AZ 93 coating were considered in the ATCS for lunar missions. A Simulink/MATLAB model of the ATCS was used to compute the ATCS performance. Some major hot phases on the thermal timeline were selected because of concern about the large amount of water sublimated for thermal topping. It was concluded that an ATCS with an RC seven-panel radiator could be used for both ISS and lunar missions, but with two different coatings STC for ISS missions and AZ 93 for lunar missions to provide performance similar to or better than that of the LM baseline ATCS.

  4. Micromagnetic simulations of thermally activated magnetization reversal of nanoscale magnets

    NASA Astrophysics Data System (ADS)

    Brown, Gregory; Novotny, M. A.; Rikvold, Per Arne

    2000-05-01

    Numerical integration of a stochastic Landau-Lifshitz-Gilbert equation is used to study dynamic processes in single-domain nanoscale magnets at nonzero temperatures. Special attention is given to including thermal fluctuations as a Langevin term, and the fast multipole method is used to calculate dipole-dipole interactions. It is feasible to simulate these dynamics on the nanosecond time scale for spatial discretizations that involve on the order of 104 nodes using a desktop workstation. The nanoscale magnets considered here are single pillars with large aspect ratio. Hysteresis-loop simulations are employed to study the stable and metastable configurations of the magnetization. Each pillar has magnetic end caps. In a time-dependent field the magnetization of the pillars is observed to reverse via nucleation, propagation, and coalescence of the end caps. In particular, the end caps propagate into the magnet and meet near the middle. A relatively long-lived defect is formed when end caps with opposite vorticity meet. Fluctuations are more important in the reversal of the magnetization for fields weaker than the zero-temperature coercive field, where the reversal is thermally activated. In this case, the process must be described by its statistical properties, such as the distribution of switching times, averaged over a large number of independent thermal histories.

  5. Evaluating Three Active Thermal Architectures for Exploration Missions

    NASA Technical Reports Server (NTRS)

    Cross, Cynthia D.; Hong, Andrew E.; Sheth, Rubik B.; Navarro, Moses; Marett, Susan J.

    2012-01-01

    Mass and cost are typically the two biggest challenges facing space craft designers. Active thermal control systems for crewed space-craft are typically among the more massive and costly systems on the vehicle. A study was completed evaluating three different thermal control system architectures to evaluate overall performance, mass and cost for a typical exploration mission profile. The architectures that were evaluated were 1 - a two-loop system using an internal liquid loop interfacing with an external liquid loop and flow loop with flow through radiators; 2 - a-single loop architecture with flow through radiators utilizing a regenerative heat exchanger and heater; and 3 - a single-loop architecture with heat pipe radiators. Environmental conditions, calculated for a given lunar exploration mission, and mission heat load profiles, generated based on previous Orion time lines, were evalauated through the phases of the on orbit mission. Performance for each of the architectures was evaluated along with the resultant mass of each system. Recommendations include adding a thermal topping system to lunar missions due to the extreme hot environments encountered in near-lunar approaches.

  6. A precision, thermally-activated driver for space application

    NASA Technical Reports Server (NTRS)

    Murray, Robert C.; Walsh, Robert F.; Kinard, William H.

    1986-01-01

    A space qualified, precision, large force, thermally-activated driver that has been developed jointly by the NASA Langley Research Center and PRC Kentron is described. The driver consists of a sealed hydraulic cylinder containing a metal bellows, a bellows plug, a coil spring, a spring retainer, and output shaft, a shaft guide, and a quantity of silicone oil. Temperature changes cause the silicone oil to expand or contract thus contracting or expanding the bellows/spring assembly thereby extending or retracting the output shaft.

  7. Compensation for thermally induced birefringence in polycrystalline ceramic active elements

    SciTech Connect

    Kagan, M A; Khazanov, E A

    2003-10-31

    Polycrystalline ceramics differ significantly from single crystals in that the crystallographic axes (and hence of the axes of thermally induced birefringence) are oriented randomly in each granule of the ceramic. The quaternion formalism is employed to calculate the depolarisation in the ceramics and the efficiency of its compensation. The obtained analytic expressions are in good agreement with the numerical relations. It is shown that the larger the ratio of the sample length to the granule size, the closer the properties of the ceramics to those of a single crystal with the [111] orientation (in particular, the uncompensated depolarisation is inversely proportional to this ratio). (active media)

  8. Porous materials for thermal management under extreme conditions.

    PubMed

    Clyne, T W; Golosnoy, I O; Tan, J C; Markaki, A E

    2006-01-15

    A brief analysis is presented of how heat transfer takes place in porous materials of various types. The emphasis is on materials able to withstand extremes of temperature, gas pressure, irradiation, etc. i.e. metals and ceramics, rather than polymers. A primary aim is commonly to maximize either the thermal resistance (i.e. provide insulation) or the rate of thermal equilibration between the material and a fluid passing through it (i.e. to facilitate heat exchange). The main structural characteristics concern porosity (void content), anisotropy, pore connectivity and scale. The effect of scale is complex, since the permeability decreases as the structure is refined, but the interfacial area for fluid-solid heat exchange is, thereby, raised. The durability of the pore structure may also be an issue, with a possible disadvantage of finer scale structures being poor microstructural stability under service conditions. Finally, good mechanical properties may be required, since the development of thermal gradients, high fluid fluxes, etc. can generate substantial levels of stress. There are, thus, some complex interplays between service conditions, pore architecture/scale, fluid permeation characteristics, convective heat flow, thermal conduction and radiative heat transfer. Such interplays are illustrated with reference to three examples: (i) a thermal barrier coating in a gas turbine engine; (ii) a Space Shuttle tile; and (iii) a Stirling engine heat exchanger. Highly porous, permeable materials are often made by bonding fibres together into a network structure and much of the analysis presented here is oriented towards such materials. PMID:18272456

  9. Thermal Neutron Imaging in an Active Interrogation Environment

    SciTech Connect

    Vanier, Peter E.; Forman, Leon; Norman, Daren R.

    2009-03-10

    We have developed a thermal-neutron coded-aperture imager that reveals the locations of hydrogenous materials from which thermal neutrons are being emitted. This imaging detector can be combined with an accelerator to form an active interrogation system in which fast neutrons are produced in a heavy metal target by means of excitation by high energy photons. The photo-induced neutrons can be either prompt or delayed, depending on whether neutron-emitting fission products are generated. Provided that there are hydrogenous materials close to the target, some of the photo-induced neutrons slow down and emerge from the surface at thermal energies. These neutrons can be used to create images that show the location and shape of the thermalizing materials. Analysis of the temporal response of the neutron flux provides information about delayed neutrons from induced fission if there are fissionable materials in the target. The combination of imaging and time-of-flight discrimination helps to improve the signal-to-background ratio. It is also possible to interrogate the target with neutrons, for example using a D-T generator. In this case, an image can be obtained from hydrogenous material in a target without the presence of heavy metal. In addition, if fissionable material is present in the target, probing with fast neutrons can stimulate delayed neutrons from fission, and the imager can detect and locate the object of interest, using appropriate time gating. Operation of this sensitive detection equipment in the vicinity of an accelerator presents a number of challenges, because the accelerator emits electromagnetic interference as well as stray ionizing radiation, which can mask the signals of interest.

  10. Thermal neutron imaging in an active interrogation environment

    SciTech Connect

    Vanier,P.E.; Forman, L., and Norman, D.R.

    2009-03-10

    We have developed a thermal-neutron coded-aperture imager that reveals the locations of hydrogenous materials from which thermal neutrons are being emitted. This imaging detector can be combined with an accelerator to form an active interrogation system in which fast neutrons are produced in a heavy metal target by means of xcitation by high energy photons. The photo-induced neutrons can be either prompt or delayed, depending on whether neutronemitting fission products are generated. Provided that there are hydrogenous materials close to the target, some of the photo-induced neutrons slow down and emerge from the surface at thermal energies. These neutrons can be used to create images that show the location and shape of the thermalizing materials. Analysis of the temporal response of the neutron flux provides information about delayed neutrons from induced fission if there are fissionable materials in the target. The combination of imaging and time-of-flight discrimination helps to improve the signal-to-background ratio. It is also possible to interrogate the target with neutrons, for example using a D-T generator. In this case, an image can be obtained from hydrogenous material in a target without the presence of heavy metal. In addition, if fissionable material is present in the target, probing with fast neutrons can stimulate delayed neutrons from fission, and the imager can detect and locate the object of interest, using appropriate time gating. Operation of this sensitive detection equipment in the vicinity of an accelerator presents a number of challenges, because the accelerator emits electromagnetic interference as well as stray ionizing radiation, which can mask the signals of interest.

  11. Brazing of Carbon Carbon Composites to Cu-clad Molybdenum for Thermal Management Applications

    NASA Technical Reports Server (NTRS)

    Singh, M.; Asthana, R.; Shpargel, T> P.

    2007-01-01

    Advanced carbon carbon composites were joined to copper-clad molybdenum (Cu/Mo) using four active metal brazes containing Ti (Cu ABA, Cusin-1 ABA, Ticuni, and Ticusil) for potential use in thermal management applications. The brazed joints were characterized using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and Knoop microhardness measurements across the joint region. Metallurgically sound C-C/Cu/Mo joints, devoid of interfacial cracks formed in all cases. The joint interfaces were preferentially enriched in Ti, with Cu ABA joints exhibiting the largest interfacial Ti concentrations. The microhardness measurements revealed hardness gradients across the joint region, with a peak hardness of 300-350 KHN in Cusin-1 ABA and Ticusil joints and 200-250 KHN in Cu ABA and Ticuni joints, respectively.

  12. Tools for Designing Thermal Management of Batteries in Electric Drive Vehicles (Presentation)

    SciTech Connect

    Pesaran, A.; Keyser, M.; Kim, G. H.; Santhanagopalan, S.; Smith, K.

    2013-02-01

    Temperature has a significant impact on life, performance, and safety of lithium-ion battery technology, which is expected to be the energy storage of choice for electric drive vehicles (xEVs). High temperatures degrade Li-ion cells faster while low temperatures reduce power and energy capabilities that could have cost, reliability, range, or drivability implications. Thermal management of battery packs in xEVs is essential to keep the cells in the desired temperature range and also reduce cell-to-cell temperature variations, both of which impact life and performance. The value that the battery thermal management system provides in reducing battery life and improving performance outweighs its additional cost and complexity. Tools that are essential for thermal management of batteries are infrared thermal imaging, isothermal calorimetry, thermal conductivity meter and computer-aided thermal analysis design software. This presentation provides details of these tools that NREL has used and we believe are needed to design right-sized battery thermal management systems.

  13. Method and apparatus for thermal management of vehicle exhaust systems

    DOEpatents

    Benson, David K.; Potter, Thomas F.

    1995-01-01

    A catalytic converter is surrounded by variable conductance insulation for maintaining the operating temperature of the catalytic converter at an optimum level, for inhibiting heat loss when raising catalytic converter temperature to light-off temperature, for storing excess heat to maintain or accelerate reaching light-off temperature, and for conducting excess heat away from the catalytic converter after reaching light-off temperature. The variable conductance insulation includes vacuum gas control and metal-to-metal thermal shunt mechanisms. Radial and axial shielding inhibits radiation and convection heat loss. Thermal storage media includes phase change material, and heat exchanger chambers and fluids carry heat to and from the catalytic converter.

  14. 77 FR 31615 - Improving Mail Management Policies, Procedures, and Activities

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-29

    ... ADMINISTRATION Improving Mail Management Policies, Procedures, and Activities AGENCY: Office of Governmentwide... Services Administration (GSA) has issued Federal Management Regulation (FMR) Bulletin G-03 which provides guidance to Executive Branch agencies for improving mail management policies, procedures, and...

  15. Decision Support for Active Water Management (Invited)

    NASA Astrophysics Data System (ADS)

    Maidment, D. R.; Salas, F.; Minsker, B. S.

    2013-12-01

    Active water management refers to real-time adjustment of water management decisions based on observation and modeling of current water conditions. A case study is presented of a decision-support system for active water management in the San Antonio and Guadalupe basins using web services and cloud computing to create at the University of Texas a repository of observations, forecasts and model simulations from federal, state and regional water agencies and academia. Each day, National Weather Service river flow forecasts at 47 points in the basin are densified to create corresponding flows in 5500 river reaches using the RAPID river flow model operated in "Model as a Service" mode at the University of Illinois. These flows are adjusted by using the "Declarations of Intent" to pump water compiled by the Texas Commission for Environmental Quality which is the WaterMaster for all surface water withdrawals in the basin. The results are viewed through web maps that convey both maps of the spatial pattern of flow at a particular point in time, and charts of time series of flows at particular points in space.

  16. Thermal behaviour of arsenic trioxide adsorbed on activated carbon.

    PubMed

    Cuypers, Frederic; De Dobbelaere, Christopher; Hardy, An; Van Bael, Marlies K; Helsen, Lieve

    2009-07-30

    The thermal stability and desorption of arsenic trioxide (As(2)O(3)) adsorbed on activated carbon (AC) was investigated as this phenomenon is expected to influence the arsenic release during low temperature pyrolysis of chromated copper arsenate (CCA) wood waste. Firstly, a thermogravimetric (TG) experiment with arsenolite, an allotropic form of As(2)O(3), was performed. The sample starts to sublime at temperatures lower than 200 degrees C with a sublimation peak temperature of 271 degrees C. Subsequently, TG experiments with samples of As(2)O(3) adsorbed on AC revealed that only very little (max. 6+/-3 wt%) As(2)O(3) was volatilized at temperatures below 280 degrees C, while still 41.6 (+/-5)wt% of the original arsenic concentration was retained at 440 degrees C and 28.5 (+/-3)wt% at 600 degrees C. The major arsenic volatilization occurred between 300 degrees C and 500 degrees C. The kinetic parameters of desorption, activation energy of desorption (E(d)) and pre-exponential factor (A), were determined by fitting an Arrhenius model to the experimental data, resulting in E(d)=69 kJ/mol, A=1.21 x 10(4)s(-1). It can be concluded that the adsorption of As(2)O(3) on AC can contribute to the thermal stabilisation of As(2)O(3). Consequently, during low temperature pyrolysis of CCA wood arsenic release may be prevented by adsorption of As(2)O(3) on the coal-type product formed during the thermal decomposition of the wood. PMID:19136209

  17. Power Electronics Thermal Management R&D; NREL (National Renewable Energy Laboratory)

    SciTech Connect

    Waye, Scot

    2015-06-10

    Presentation containing an update for the Power Electronics Thermal Management project in the Electric Drive Train task funded by the Vehicle Technology Office of DOE. This presentation outlines the purpose, plan, and results of research thus far for cooling and material selection strategies to manage heat in power electronic assemblies such as inverters, converters, and chargers.

  18. Magnetization Reversal and Thermal Activation in Co/Pt Multilayers

    NASA Astrophysics Data System (ADS)

    Meldrim, J. Mark; Kirby, Roger; Sellmyer, David

    2000-03-01

    Co/Pt multilayers not only display interesting intrinsic magnetic properties such as perpendicular anisotropy but also have technological applications. As grain sizes become smaller and smaller, the role of thermal activation becomes important in understanding magnetization reversal [1,2]. We have prepared [Co 3 Å/Pt 9 Å] x N thin films where N ranges from 6 to 24 by DC magnetron sputtering at various Ar pressures. As the sputtering gas pressure is changed, we find the lateral grain size changes from 20 nm to 45 nm. At the same time, the hysteresis loops become less square and the coercivity increases from a few hundred Oe to above 5 kOe. Activation volumes were determined for the samples both by the field sweep rate method and viscosity measurements. These results will be discussed in terms of simple models of thermally assisted magnetization reversal. This work is supported by NFS grant DMR 9623992 and CMRA. [1] J. S. Shen, R. D. Kirby, K. Wierman, Z. S. Shan, and D. J. Sellmyer, J. App. Phys. 73, 6418 (1993). [2] X. Chen and M. H. Kryder. J. App. Phys. 85, 5006 (1999).

  19. Allosterism and Structure in Thermally Activated Transient Receptor Potential Channels.

    PubMed

    Diaz-Franulic, Ignacio; Poblete, Horacio; Miño-Galaz, Germán; González, Carlos; Latorre, Ramón

    2016-07-01

    The molecular sensors that mediate temperature changes in living organisms are a large family of proteins known as thermosensitive transient receptor potential (TRP) ion channels. These membrane proteins are polymodal receptors that can be activated by cold or hot temperatures, depending on the channel subtype, voltage, and ligands. The stimuli sensors are allosterically coupled to a pore domain, increasing the probability of finding the channel in its ion conductive conformation. In this review we first discuss the allosteric coupling between the temperature and voltage sensor modules and the pore domain, and then discuss the thermodynamic foundations of thermo-TRP channel activation. We provide a structural overview of the molecular determinants of temperature sensing. We also posit an anisotropic thermal diffusion model that may explain the large temperature sensitivity of TRP channels. Additionally, we examine the effect of several ligands on TRP channel function and the evidence regarding their mechanisms of action. PMID:27297398

  20. Management of patients with active caries.

    PubMed

    Milgrom, Peter

    2014-07-01

    This paper reports on a mechanism to manage caries as a disease and to medically intervene in the disease process to halt progression. The goal of this paper is to provide this alternative to a surgical-only approach. The management of caries begins with assessing lesion activity and the potential for arrest. This requires a clinical and radiological assessment and evaluation of risk. Hopeless teeth are extracted and large cavities filled to reduce infection. Risk reduction strategies are employed so efforts to arrest lesions can be successful. Teeth with lesions in the enamel or outer third of the dentin should be sealed, not restored, as restorations can weaken teeth and can be traumatic to pulps. PMID:25076627

  1. High conductivity, low cost aluminum composite for thermal management

    SciTech Connect

    Sommer, J.L.

    1997-04-01

    In order to produce an inexpensive packaging material that exhibits high thermal conductivity and low CTE, Technical Research Associates, Inc. (TRA) has shown in Phase I the feasibility of incorporating natural flake graphite in an aluminum matrix. TRA has developed a proprietary coating technique where graphite flakes have been coated with a thin layer of molybdenum/molybdenum carbide (approximately 0.2 microns). This barrier coating can protect the graphite flake from chemical reaction and high temperature degradation in molten aluminum silicon alloys. Methods to successfully vacuum infiltrate coated flake with molten aluminum alloys were developed. The resulted metal matrix composites exhibited lower CTE than aluminum metal. The CTE of the composites were significantly lower than aluminum and its alloys. The CTE can potentially be tailored for specific applications. The in plane thermal conductivity was higher than the aluminum matrix alloy. The thermal conductivity and CTE of the composite may be significantly improved by improving the bond strength of the molybdenum coating on the graphite flake. The flake can potentially be incorporated in the molten aluminum and pressure die cast to align the flakes within the aluminum matrix. By preferentially aligning high conductivity graphite flakes within a plane or direction, the thermal conductivity of the resulting composite will be above pure aluminum in the alignment direction.

  2. Thermal shell fragment craniofacial injury: biophysics, pathophysiology, and management.

    PubMed

    Shuker, Sabri T

    2015-01-01

    This article aims to bring attention to unique risks and burns by thermal shell fragment craniofacial soft tissue injury. Hot shrapnel may inflict burns to major vessel walls and lead to life-threatening hemorrhaging or death, which adds a new challenge for craniofacial surgeons. Morbidity of thermal deep tissue may lead to deep tissue necrosis and infection.Thermal energy (TE) physics, biophysics, and pathophysiological effects relate directly to the amount of heat generated from shell casing detonation, which transfers to skin, deep tissue, as well as brain and leads to life-threatening burning of organs; this is different from shrapnel kinetic energy injury.The unprecedented increase in using a large range of explosives and high-heat thermobaric weapons contributes to the superfluous and unnecessary suffering caused by thermal injury wounds.Surgeons and medics should recognize that a surprising amount of TE can be found in an explosion or detonation of a steel-encased explosive, resulting in TEs ranging from 400 F up to 1000 F. PMID:25534053

  3. Interpretation of Thermal Infrared Imagery for Irrigation Water Resource Management.

    ERIC Educational Resources Information Center

    Nellis, M. Duane

    1985-01-01

    Water resources play a major role in the character of agricultural development in the arid western United States. This case study shows how thermal infrared imagery, which is sensitive to radiant or heat energy, can be used to interpret crop moisture content and associated stress in irrigated areas. (RM)

  4. Thermal imaging of Erta 'Ale active lava lake (Ethiopia)

    NASA Astrophysics Data System (ADS)

    Spampinato, L.; Oppenheimer, C.; Calvari, S.; Cannata, A.; Montalto, P.

    2009-04-01

    Active lava lakes represent the uppermost portion of a volume of convective magma exposed to the atmosphere, and provide open windows on magma dynamics within shallow reservoirs. Erta ‘Ale volcano located within the Danakil Depression in Ethiopia, hosts one of the few permanent convecting lava lakes, active at least since the last century. We report here the main features of Erta ‘Ale lake surface investigated using a hand-held infrared thermal camera between 11 and 12 November 2006. In both days, the lake surface was mainly characterized by efficient magma circulation reflecting in the formation of well-marked incandescent cracks and wide crust plates. These crossed the lake from the upwelling to the downwelling margin with mean speeds ranging between 0.01 and 0.15 m s-1. Hot spots opened eventually in the middle of crust plates and/or along cracks. These produced explosive activity lasting commonly between ~10 and 200 sec. Apparent temperatures at cracks ranged between ~700 and 1070˚C, and between ~300 and 500˚C at crust plates. Radiant power output of the lake varied between ~45 and 76 MW according to the superficial activity and continuous resurfacing of the lake. Time series analysis of the radiant power output data reveals cyclicity with a period of ~10 min. The combination of visual and thermal observations with apparent mean temperatures and convection rates allows us to interpret these signals as the periodic release of hot overpressured gas bubbles at the lake surface.

  5. Design for manufacturability production management activity report

    NASA Astrophysics Data System (ADS)

    Miyazaki, Norihiko; Sato, T.; Honma, M.; Yoshioka, N.; Hosono, K.; Onodera, T.; Itoh, H.; Suzuki, H.; Uga, T.; Kadota, K.; Iriki, N.

    2006-05-01

    Design For Manufacturability Production Management (DFM-PM) Subcommittee has been started in succession to Reticle Management Subcommittee (RMS) in Semiconductor Manufacturing Technology Committee for Japan (SMTCJ) from 2005. Our activity focuses on the SoC (System On Chip) Business, and it pursues the improvement of communication in manufacturing technique. The first theme of activity is the investigation and examination of the new trends about production (manufacturer) technology and related information, and proposals of business solution. The second theme is the standardization activity about manufacture technology and the cooperation with related semiconductors' organizations. And the third theme is holding workshop and support for promotion and spread of the standardization technology throughout semiconductor companies. We expand a range of scope from design technology to wafer pattern reliability and we will propose the competition domain, the collaboration area and the standardization technology on DFM. Furthermore, we will be able to make up a SoC business model as the 45nm node technology beyond manufacturing platform in cooperating with the design information and the production information by utilizing EDA technology.

  6. Thermal management of power sources for mobile electronic devices based on micro-SOFC

    NASA Astrophysics Data System (ADS)

    Murayama, S.; Iguchi, F.; Shimizu, M.; Yugami, H.

    2014-11-01

    Small power sources based on micro-SOFC for mobile electronic devices required two conditions, i,e, thermally compatibility and thermally self-sustain, because of high operating temperature over 300 oC. Moreover, high energy efficiency was also required. It meant that this system should be designed considering thermal management. In this study, we developed micro-SOFC packages which have three functions, thermal insulation, thermal recovery, and self-heating. Heat conduction analysis based on finite element method, and thermochemical calculation revealed that vacuum thermal insulation was effective for size reduction and gas-liquid heat exchanger could reduce the temperature of outer surface. We fabricated the package with three functions for proof of concept and evaluated. As a result, it was suggested that developed package could satisfy both two requirements with high efficiency.

  7. Firearm suppressor having enhanced thermal management for rapid heat dissipation

    DOEpatents

    Moss, William C.; Anderson, Andrew T.

    2014-08-19

    A suppressor is disclosed for use with a weapon having a barrel through which a bullet is fired. The suppressor has an inner portion having a bore extending coaxially therethrough. The inner portion is adapted to be secured to a distal end of the barrel. A plurality of axial flow segments project radially from the inner portion and form axial flow paths through which expanding propellant gasses discharged from the barrel flow through. The axial flow segments have radially extending wall portions that define sections which may be filled with thermally conductive material, which in one example is a thermally conductive foam. The conductive foam helps to dissipate heat deposited within the suppressor during firing of the weapon.

  8. Method and apparatus for thermal management of vehicle exhaust systems

    DOEpatents

    Benson, D.K.; Potter, T.F.

    1995-12-26

    A catalytic converter is surrounded by variable conductance insulation for maintaining the operating temperature of the catalytic converter at an optimum level, for inhibiting heat loss when raising catalytic converter temperature to light-off temperature, for storing excess heat to maintain or accelerate reaching light-off temperature, and for conducting excess heat away from the catalytic converter after reaching light-off temperature. The variable conductance insulation includes vacuum gas control and metal-to-metal thermal shunt mechanisms. Radial and axial shielding inhibits radiation and convection heat loss. Thermal storage media includes phase change material, and heat exchanger chambers and fluids carry heat to and from the catalytic converter. 7 figs.

  9. H2S mediated thermal and photochemical methane activation

    PubMed Central

    Baltrusaitis, Jonas; de Graaf, Coen; Broer, Ria; Patterson, Eric

    2013-01-01

    Sustainable, low temperature methods of natural gas activation are critical in addressing current and foreseeable energy and hydrocarbon feedstock needs. Large portions of natural gas resources are still too expensive to process due to their high content of hydrogen sulfide gas (H2S) in mixture with methane, CH4, altogether deemed as sub-quality or “sour” gas. We propose a unique method for activating this “sour” gas to form a mixture of sulfur-containing hydrocarbon intermediates, CH3SH and CH3SCH3, and an energy carrier, such as H2. For this purpose, we computationally investigated H2S mediated methane activation to form a reactive CH3SH species via direct photolysis of sub-quality natural gas. Photoexcitation of hydrogen sulfide in the CH4+H2S complex results in a barrier-less relaxation via a conical intersection to form a ground state CH3SH+H2 complex. The resulting CH3SH can further be heterogeneously coupled over acidic catalysts to form higher hydrocarbons while the H2 can be used as a fuel. This process is very different from a conventional thermal or radical-based processes and can be driven photolytically at low temperatures, with enhanced controllability over the process conditions currently used in industrial oxidative natural gas activation. Finally, the proposed process is CO2 neutral, as opposed to the currently industrially used methane steam reforming (SMR). PMID:24150813

  10. Tables for simplifying calculations of activities produced by thermal neutrons

    USGS Publications Warehouse

    Senftle, F.E.; Champion, W.R.

    1954-01-01

    The method of calculation described is useful for the types of work of which examples are given. It is also useful in making rapid comparison of the activities that might be expected from several different elements. For instance, suppose it is desired to know which of the three elements, cobalt, nickel, or vanadium is, under similar conditions, activated to the greatest extent by thermal neutrons. If reference is made to a cross-section table only, the values may be misleading unless properly interpreted by a suitable comparison of half-lives and abundances. In this table all the variables have been combined and the desired information can be obtained directly from the values of A 3??, the activity produced per gram per second of irradiation, under the stated conditions. Hence, it is easily seen that, under similar circumstances of irradiation, vanadium is most easily activated even though the cross section of one of the cobalt isotopes is nearly five times that of vanadium and the cross section of one of the nickel isotopes is three times that of vanadium. ?? 1954 Societa?? Italiana di Fisica.

  11. Thermal Management Design for the X-33 Lifting Body

    NASA Technical Reports Server (NTRS)

    Bouslog, S.; Mammano, J.; Strauss, B.

    1998-01-01

    The X-33 Advantage Technology Demonstrator offers a rare and exciting opportunity in Thermal Protection System development. The experimental program incorporates the latest design innovation in re-useable, low life cycle cost, and highly dependable Thermal Protection materials and constructions into both ground based and flight test vehicle validations. The unique attributes of the X-33 demonstrator for design application validation for the full scale Reusable Launch Vehicle, (RLV), are represented by both the configuration of the stand-off aeroshell, and the extreme exposures of sub-orbital hypersonic re-entry simulation. There are several challenges of producing a sub-orbital prototype demonstrator of Single Stage to Orbit/Reusable Launch Vehicle (SSTO/RLV) operations. An aggressive schedule with budgetary constraints precludes the opportunity for an extensive verification and qualification program of vehicle flight hardware. However, taking advantage of off the shelf components with proven technologies reduces some of the requirements for additional testing. The effects of scale on thermal heating rates must also be taken into account during trajectory design and analysis. Described in this document are the unique Thermal Protection System (TPS) design opportunities that are available with the lifting body configuration of the X-33. The two principal objectives for the TPS are to shield the primary airframe structure from excessive thermal loads and to provide an aerodynamic mold line surface. With the relatively benign aeroheating capability of the lifting body, an integrated stand-off aeroshell design with minimal weight and reduced procurement and operational costs is allowed. This paper summarizes the design objectives of the X-33 TPS, the flight test requirements driven configuration, and design benefits. Comparisons are made of the X-33 flight profiles and Space Shuttle Orbiter, and lifting body Reusable Launch Vehicle aerothermal environments. The X-33

  12. Thermal tracking in mobile robots for leak inspection activities.

    PubMed

    Ibarguren, Aitor; Molina, Jorge; Susperregi, Loreto; Maurtua, Iñaki

    2013-01-01

    Maintenance tasks are crucial for all kind of industries, especially in extensive industrial plants, like solar thermal power plants. The incorporation of robots is a key issue for automating inspection activities, as it will allow a constant and regular control over the whole plant. This paper presents an autonomous robotic system to perform pipeline inspection for early detection and prevention of leakages in thermal power plants, based on the work developed within the MAINBOT (http://www.mainbot.eu) European project. Based on the information provided by a thermographic camera, the system is able to detect leakages in the collectors and pipelines. Beside the leakage detection algorithms, the system includes a particle filter-based tracking algorithm to keep the target in the field of view of the camera and to avoid the irregularities of the terrain while the robot patrols the plant. The information provided by the particle filter is further used to command a robot arm, which handles the camera and ensures that the target is always within the image. The obtained results show the suitability of the proposed approach, adding a tracking algorithm to improve the performance of the leakage detection system. PMID:24113684

  13. Thermally activated diffusion of magnesium from bioapatite crystals

    NASA Astrophysics Data System (ADS)

    Danil'Chenko, S. N.; Kulik, A. N.; Pavlenko, P. A.; Kalinichenko, T. G.; Bugai, A. N.; Chemeris, I. I.; Sukhodub, L. F.

    2006-05-01

    We have attempted to use heat treatment followed by ultrasonic treatment to separate the apatite from the non-apatite components of bone mineral in samples from different animals. The Mg content and the Ca/P ratio in the temperature range 560°C-720°C in the samples before and after ultrasonic treatment were determined by electron-probe x-ray microanalysis. Furthermore, we used atomic absorption spectrometry to measure the Mg content in powdered bone samples only after annealing and in distilled water, which was the “sonication” medium. We obtained evidence for thermally activated transition of Mg from a structurally bound state to a labile state at 680°C-720°C. At the same temperature, the Ca-deficient apatite is transformed to stoichiometric apatite. The data presented are evidence that crystals of Ca-deficient bioapatite are surrounded by Ca-enriched surface layers. As a result of thermal transformations at 680°C-720°C, all the Mg in the biomineral is found in the non-apatite environment surrounding the crystals and is removed by ultrasonic treatment, while the surface-localized Ca penetrates into the apatite lattice, restoring its stoichiometry.

  14. Thermally activated charge transport in microbial protein nanowires

    PubMed Central

    Lampa-Pastirk, Sanela; Veazey, Joshua P.; Walsh, Kathleen A.; Feliciano, Gustavo T.; Steidl, Rebecca J.; Tessmer, Stuart H.; Reguera, Gemma

    2016-01-01

    The bacterium Geobacter sulfurreducens requires the expression of conductive protein filaments or pili to respire extracellular electron acceptors such as iron oxides and uranium and to wire electroactive biofilms, but the contribution of the protein fiber to charge transport has remained elusive. Here we demonstrate efficient long-range charge transport along individual pili purified free of metal and redox organic cofactors at rates high enough to satisfy the respiratory rates of the cell. Carrier characteristics were within the orders reported for organic semiconductors (mobility) and inorganic nanowires (concentration), and resistivity was within the lower ranges reported for moderately doped silicon nanowires. However, the pilus conductance and the carrier mobility decreased when one of the tyrosines of the predicted axial multistep hopping path was replaced with an alanine. Furthermore, low temperature scanning tunneling microscopy demonstrated the thermal dependence of the differential conductance at the low voltages that operate in biological systems. The results thus provide evidence for thermally activated multistep hopping as the mechanism that allows Geobacter pili to function as protein nanowires between the cell and extracellular electron acceptors. PMID:27009596

  15. A militarily fielded thermal neutron activation sensor for landmine detection

    NASA Astrophysics Data System (ADS)

    Clifford, E. T. H.; McFee, J. E.; Ing, H.; Andrews, H. R.; Tennant, D.; Harper, E.; Faust, A. A.

    2007-08-01

    The Canadian Department of National Defence has developed a teleoperated, vehicle-mounted, multi-sensor system to detect anti-tank landmines on roads and tracks in peacekeeping operations. A key part of the system is a thermal neutron activation (TNA) sensor which is placed above a suspect location to within a 30 cm radius and confirms the presence of explosives via detection of the 10.835 MeV gamma ray associated with thermal neutron capture on 14N. The TNA uses a 100 μg252Cf neutron source surrounded by four 7.62 cm×7.62 cm NaI(Tl) detectors. The system, consisting of the TNA sensor head, including source, detectors and shielding, the high-rate, fast pulse processing electronics and the data processing methodology are described. Results of experiments to characterize detection performance are also described. The experiments have shown that anti-tank mines buried 10 cm or less can be detected in roughly a minute or less, but deeper mines and mines significantly displaced horizontally take considerably longer time. Mines as deep as 30 cm can be detected for long count times (1000 s). Four TNA detectors are now in service with the Canadian Forces as part of the four multi-sensor systems, making it the first militarily fielded TNA sensor and the first militarily fielded confirmation sensor for landmines. The ability to function well in adverse climatic conditions has been demonstrated, both in trials and operations.

  16. Thermally activated charge transport in microbial protein nanowires.

    PubMed

    Lampa-Pastirk, Sanela; Veazey, Joshua P; Walsh, Kathleen A; Feliciano, Gustavo T; Steidl, Rebecca J; Tessmer, Stuart H; Reguera, Gemma

    2016-01-01

    The bacterium Geobacter sulfurreducens requires the expression of conductive protein filaments or pili to respire extracellular electron acceptors such as iron oxides and uranium and to wire electroactive biofilms, but the contribution of the protein fiber to charge transport has remained elusive. Here we demonstrate efficient long-range charge transport along individual pili purified free of metal and redox organic cofactors at rates high enough to satisfy the respiratory rates of the cell. Carrier characteristics were within the orders reported for organic semiconductors (mobility) and inorganic nanowires (concentration), and resistivity was within the lower ranges reported for moderately doped silicon nanowires. However, the pilus conductance and the carrier mobility decreased when one of the tyrosines of the predicted axial multistep hopping path was replaced with an alanine. Furthermore, low temperature scanning tunneling microscopy demonstrated the thermal dependence of the differential conductance at the low voltages that operate in biological systems. The results thus provide evidence for thermally activated multistep hopping as the mechanism that allows Geobacter pili to function as protein nanowires between the cell and extracellular electron acceptors. PMID:27009596

  17. Thermal Tracking in Mobile Robots for Leak Inspection Activities

    PubMed Central

    Ibarguren, Aitor; Molina, Jorge; Susperregi, Loreto; Maurtua, Iñaki

    2013-01-01

    Maintenance tasks are crucial for all kind of industries, especially in extensive industrial plants, like solar thermal power plants. The incorporation of robots is a key issue for automating inspection activities, as it will allow a constant and regular control over the whole plant. This paper presents an autonomous robotic system to perform pipeline inspection for early detection and prevention of leakages in thermal power plants, based on the work developed within the MAINBOT (http://www.mainbot.eu) European project. Based on the information provided by a thermographic camera, the system is able to detect leakages in the collectors and pipelines. Beside the leakage detection algorithms, the system includes a particle filter-based tracking algorithm to keep the target in the field of view of the camera and to avoid the irregularities of the terrain while the robot patrols the plant. The information provided by the particle filter is further used to command a robot arm, which handles the camera and ensures that the target is always within the image. The obtained results show the suitability of the proposed approach, adding a tracking algorithm to improve the performance of the leakage detection system. PMID:24113684

  18. A study of thermally activated delayed fluorescence in C 60

    NASA Astrophysics Data System (ADS)

    Salazar, Filipa A.; Fedorov, Aleksandre; Berberan-Santos, Mário N.

    1997-06-01

    The existence of thermally activated delayed fluorescence in C 60 is demonstrated by the study of the temperature dependence (291-353 K) of the fluorescence intensity of C 60 degassed solutions. The determined singlet-triplet energy gap, 35 ± 2 kJ/mol, agrees with the value calculated from previously reported fluorescence and low temperature phosphorescence spectra for this molecule (35 kJ/mol). The estimated quantum yield of triplet formation, 0.8 ± 0.1, agrees with previous determinations. The fluorescence lifetime of C 60, also measured, τ = 1.1 ns, does not change appreciably with excitation wavelength, degassing nor with temperature, in the range 243-343 K.

  19. Mechanism of intersystem crossing of thermally activated delayed fluorescence molecules.

    PubMed

    Ogiwara, Toshinari; Wakikawa, Yusuke; Ikoma, Tadaaki

    2015-04-01

    The spin sublevel dynamics of the excited triplet state in thermally activated delayed fluorescence (TADF) molecules have not been investigated for high-intensity organic light-emitting diode materials. Understanding the mechanism for intersystem crossing (ISC) is thus important for designing novel TADF materials. We report the first study on the ISC dynamics of the lowest excited triplet state from the lowest excited singlet state with charge-transfer (CT) character of TADF molecules with different external quantum efficiencies (EQEs) using time-resolved electron paramagnetic resonance methods. Analysis of the observed spin polarization indicates a strong correlation of the EQE with the population rate due to ISC induced by hyperfine coupling with the magnetic nuclei. It is concluded that molecules with high EQE have an extremely small energy gap between the (1)CT and (3)CT states, which allows an additional ISC channel due to the hyperfine interactions. PMID:25774790

  20. Highly efficient blue electroluminescence based on thermally activated delayed fluorescence.

    PubMed

    Hirata, Shuzo; Sakai, Yumi; Masui, Kensuke; Tanaka, Hiroyuki; Lee, Sae Youn; Nomura, Hiroko; Nakamura, Nozomi; Yasumatsu, Mao; Nakanotani, Hajime; Zhang, Qisheng; Shizu, Katsuyuki; Miyazaki, Hiroshi; Adachi, Chihaya

    2015-03-01

    Organic compounds that exhibit highly efficient, stable blue emission are required to realize inexpensive organic light-emitting diodes for future displays and lighting applications. Here, we define the design rules for increasing the electroluminescence efficiency of blue-emitting organic molecules that exhibit thermally activated delayed fluorescence. We show that a large delocalization of the highest occupied molecular orbital and lowest unoccupied molecular orbital in these charge-transfer compounds enhances the rate of radiative decay considerably by inducing a large oscillator strength even when there is a small overlap between the two wavefunctions. A compound based on our design principles exhibited a high rate of fluorescence decay and efficient up-conversion of triplet excitons into singlet excited states, leading to both photoluminescence and internal electroluminescence quantum yields of nearly 100%. PMID:25485987

  1. Highly efficient blue electroluminescence based on thermally activated delayed fluorescence

    NASA Astrophysics Data System (ADS)

    Hirata, Shuzo; Sakai, Yumi; Masui, Kensuke; Tanaka, Hiroyuki; Lee, Sae Youn; Nomura, Hiroko; Nakamura, Nozomi; Yasumatsu, Mao; Nakanotani, Hajime; Zhang, Qisheng; Shizu, Katsuyuki; Miyazaki, Hiroshi; Adachi, Chihaya

    2015-03-01

    Organic compounds that exhibit highly efficient, stable blue emission are required to realize inexpensive organic light-emitting diodes for future displays and lighting applications. Here, we define the design rules for increasing the electroluminescence efficiency of blue-emitting organic molecules that exhibit thermally activated delayed fluorescence. We show that a large delocalization of the highest occupied molecular orbital and lowest unoccupied molecular orbital in these charge-transfer compounds enhances the rate of radiative decay considerably by inducing a large oscillator strength even when there is a small overlap between the two wavefunctions. A compound based on our design principles exhibited a high rate of fluorescence decay and efficient up-conversion of triplet excitons into singlet excited states, leading to both photoluminescence and internal electroluminescence quantum yields of nearly 100%.

  2. Reducing cold-start emissions by catalytic converter thermal management

    SciTech Connect

    Burch, S D; Potter, T F; Keyser, M A; Brady, M J; Michaels, K F

    1995-01-01

    Vacuum insulation and phase-change thermal storage have been used to enhance the heat retention of a prototype catalytic converter. Storing heat in the converter between trips allows exhaust gases to be converted more quickly, significantly reducing cold-start emissions. Using a small metal hydride, the thermal conductance of the vacuum insulation can be varied continuously between 0.49 and 27 W/m{sup 2}K (R-12 to R-0.2 insulation) to prevent overheating of the catalyst. A prototype was installed in a Dodge Neon with a 2.0-liter engine. Following a standard preconditioning and a 23-hour cold soak, an FTP (Federal Test Procedure) emissions test was performed. Although exhaust temperatures during the preconditioning were not hot enough to melt the phase-change material, the vacuum insulation performed well, resulting in a converter temperature of 146{degrees}C after the 23-hour cold soak at 27{degrees}C. Compared to the same converter at ambient conditions, overall emissions of CO and HC were reduced by 52 % and 29 %, to 0.27 and 0.037 g/mile, respectively. The maximum converter temperature during the FTP cycle was 720{degrees}C. This limited testing was performed with a nearly-fresh palladium-only catalyst, but demonstrates the potential of this vacuum insulation approach for emissions reduction and thermal control. Further testing is ongoing. An initial assessment of several production issues is made, including high-volume fabrication challenges, durability, and cost.

  3. Catalysis alkene and arene hydrogenation by thermally activated silica

    SciTech Connect

    Rajagopal, V.; Guthrie, R.D.; Davis, B.H.

    1995-12-31

    Bittner, Bockrath and Solar have reported that thermal activation of fumed silica at 320{degrees}C under argon flow introduces catalytic activity for the reactions H{sub 2} + D{sub 2} {yields} 2 HD and D{sub 2} + CH{sub 2}=CH{sub 2} {yields} CH{sub 2}DCH{sub 2}D {yields} CD{sub 3}CD{sub 3}. Using the Bittner catalyst in a glass-walled, tube reactor we hydrogenate bulk samples of alkenes and arenes using D{sub 2} at pressures of 10-14 MPa and >300{degrees}C. Activation is required. Compounds hydrogenated include, stilbene, nonene, anthracene and diphenylacetylene. The aromatic rings of naphthalene, biphenyl and bibenzyl are partially hydrogenated on prolonged treatment at 350{degrees}C. At threshold temperature for the hydrogenation of diphenylacetylene, the less-stable cis-stilbene is formed faster than it proceeds to the predominantly transequilibrium mixture. Surface OH groups on the silica undergo complete equilibration to OD under our reaction conditions. However, only a barely-measurable trace of D-atom addition occurs when D{sub 2}-equilibrated silica is heated with stilbene after D{sub 2} removal.

  4. Thermal management during anaesthesia and thermoregulation standards for the prevention of inadvertent perioperative hypothermia.

    PubMed

    Torossian, Alexander

    2008-12-01

    Incidence of inadvertent perioperative hypothermia is still high, and thus thermoregulatory standards are warranted. This review summarizes current evidence of thermal management during anaesthesia, referring to recognized clinical queries (temperature measurement, definition of hypothermia, risk factors, warming methods, implementation strategies). Body temperature is a vital sign, and 37 degrees C is the mean core temperature of a healthy human. Systematic review shows that for non-invasive temperature monitoring the oral route is the most reliable; infrared ear temperature measurement is inaccurate. Intraoperatively, acceptable semi-invasive temperature monitoring sites are the nasopharynx, oesophagus and urinary bladder. Clinically relevant hypothermia starts at 36 degrees C with regard to major adverse outcomes (increased infectious complications, morbid cardiac events, coagulation disorders, prolonged length of hospital stay, and increased costs). Skin surface warming for 20 min immediately before anaesthesia (pre-warming) minimizes initial redistribution hypothermia. Intraoperatively, active warming should be applied when anaesthesia time is > 60 min. Effective methods of active warming are forced-air warming or conductive warming, provided that enough skin surface is available. Infusion fluid warming, increasing the operating room temperature, and warming of irrigation fluids are adjunctive therapies. The patient's body temperature should be above 36 degrees C before induction of anaesthesia, and should be measured continuously throughout surgery. Active warming should be applied intraoperatively. Postoperative patient temperature and outcomes should be evaluated. PMID:19137809

  5. Electrically Driven Single Phase Thermal Management: STP-H5 EHD Experiment

    NASA Technical Reports Server (NTRS)

    Didion, Jeffrey R.

    2016-01-01

    The Electrically Driven Single Phase Thermal Management: STP-H5 iEHDS Experiment is a technology demonstration of prototype proof of concept hardware to establish the feasilibilty and long term operation of this hardware. This is a structural thermal plate that will operate continuous as part of the STP-H5 ISEM experiment for up to 18 months. This presentation discusses the design, fabrication and environmental operational paramertes of the experiment hardware.

  6. Thermal Interface Materials Selection and Application Guidelines: In Perspective of Xilinx Virtex-5QV Thermal Management

    NASA Technical Reports Server (NTRS)

    Suh, Jong-ook; Dillon, R. Peter; Tseng, Stephen

    2015-01-01

    The heat from high-power microdevices for space, such as Xilinx Virtex 4 and 5 (V4 and V5), has to be removed mainly through conduction in the space vacuum environment. The class-Y type packages are designed to remove the heat from the top of the package, and the most effective method to remove heat from the class-Y type packages is to attach a heat transfer device on the lid of the package and to transfer the heat to frame or chassis. When a heat transfer device is attached to the package lid, the surfaces roughness of the package lid and the heat transfer device reduces the effective contact area between the two. The reduced contact area results in increased thermal contact resistance, and a thermal interface material is required to reduce the thermal contact resistance by filling in the gap between the surfaces of the package lid and the heat transfer device. The current report describes JPL's FY14 NEPP task study on property requirements of TIM and impact of TIM properties on the packaging reliability. The current task also developed appratuses to investigate the performances of TIMs in the actual mission environment.

  7. Atom interferometry in space: Thermal management and magnetic shielding

    SciTech Connect

    Milke, Alexander; Kubelka-Lange, André; Gürlebeck, Norman Rievers, Benny; Herrmann, Sven; Schuldt, Thilo; Braxmaier, Claus

    2014-08-15

    Atom interferometry is an exciting tool to probe fundamental physics. It is considered especially apt to test the universality of free fall by using two different sorts of atoms. The increasing sensitivity required for this kind of experiment sets severe requirements on its environments, instrument control, and systematic effects. This can partially be mitigated by going to space as was proposed, for example, in the Spacetime Explorer and Quantum Equivalence Principle Space Test (STE-QUEST) mission. However, the requirements on the instrument are still very challenging. For example, the specifications of the STE-QUEST mission imply that the Feshbach coils of the atom interferometer are allowed to change their radius only by about 260 nm or 2.6 × 10{sup −4} % due to thermal expansion although they consume an average power of 22 W. Also Earth's magnetic field has to be suppressed by a factor of 10{sup 5}. We show in this article that with the right design such thermal and magnetic requirements can indeed be met and that these are not an impediment for the exciting physics possible with atom interferometers in space.

  8. Atom interferometry in space: thermal management and magnetic shielding.

    PubMed

    Milke, Alexander; Kubelka-Lange, André; Gürlebeck, Norman; Rievers, Benny; Herrmann, Sven; Schuldt, Thilo; Braxmaier, Claus

    2014-08-01

    Atom interferometry is an exciting tool to probe fundamental physics. It is considered especially apt to test the universality of free fall by using two different sorts of atoms. The increasing sensitivity required for this kind of experiment sets severe requirements on its environments, instrument control, and systematic effects. This can partially be mitigated by going to space as was proposed, for example, in the Spacetime Explorer and Quantum Equivalence Principle Space Test (STE-QUEST) mission. However, the requirements on the instrument are still very challenging. For example, the specifications of the STE-QUEST mission imply that the Feshbach coils of the atom interferometer are allowed to change their radius only by about 260 nm or 2.6 × 10(-4) % due to thermal expansion although they consume an average power of 22 W. Also Earth's magnetic field has to be suppressed by a factor of 10(5). We show in this article that with the right design such thermal and magnetic requirements can indeed be met and that these are not an impediment for the exciting physics possible with atom interferometers in space. PMID:25173244

  9. Atom interferometry in space: Thermal management and magnetic shielding

    NASA Astrophysics Data System (ADS)

    Milke, Alexander; Kubelka-Lange, André; Gürlebeck, Norman; Rievers, Benny; Herrmann, Sven; Schuldt, Thilo; Braxmaier, Claus

    2014-08-01

    Atom interferometry is an exciting tool to probe fundamental physics. It is considered especially apt to test the universality of free fall by using two different sorts of atoms. The increasing sensitivity required for this kind of experiment sets severe requirements on its environments, instrument control, and systematic effects. This can partially be mitigated by going to space as was proposed, for example, in the Spacetime Explorer and Quantum Equivalence Principle Space Test (STE-QUEST) mission. However, the requirements on the instrument are still very challenging. For example, the specifications of the STE-QUEST mission imply that the Feshbach coils of the atom interferometer are allowed to change their radius only by about 260 nm or 2.6 × 10-4 % due to thermal expansion although they consume an average power of 22 W. Also Earth's magnetic field has to be suppressed by a factor of 105. We show in this article that with the right design such thermal and magnetic requirements can indeed be met and that these are not an impediment for the exciting physics possible with atom interferometers in space.

  10. Corrugated paraffin nanocomposite films as large stroke thermal actuators and self-activating thermal interfaces.

    PubMed

    Copic, Davor; Hart, A John

    2015-04-22

    High performance active materials are of rapidly growing interest for applications including soft robotics, microfluidic systems, and morphing composites. In particular, paraffin wax has been used to actuate miniature pumps, solenoid valves, and composite fibers, yet its deployment is typically limited by the need for external volume constraint. We demonstrate that compact, high-performance paraffin actuators can be made by confining paraffin within vertically aligned carbon nanotube (CNT) films. This large-stroke vertical actuation is enabled by strong capillary interaction between paraffin and CNTs and by engineering the CNT morphology by mechanical compression before capillary-driven infiltration of the molten paraffin. The maximum actuation strain of the corrugated CNT-paraffin films (∼0.02-0.2) is comparable to natural muscle, yet the maximum stress is limited to ∼10 kPa by collapse of the CNT network. We also show how a CNT-paraffin film can serve as a self-activating thermal interface that closes a gap when it is heated. These new CNT-paraffin film actuators could be produced by large-area CNT growth, infiltration, and lamination methods, and are attractive for use in miniature systems due to their self-contained design. PMID:25822633

  11. Improvement of thermal management in the composite Yb:YAG/YAG thin-disk laser

    NASA Astrophysics Data System (ADS)

    Kuznetsov, I. I.; Mukhin, I. B.; Palashov, O. V.

    2016-04-01

    To improve the thermal management in the composite Yb:YAG/YAG thin-disk laser a new design of laser head is developed. Thermal-induced phase distortions, small signal gain and lasing in the upgraded laser head are investigated and compared with previously published results. A substantial decrease of the thermal lens optical power and phase aberrations and increase of the laser slope efficiency are observed. A continuous-wave laser with 440 W average power and 44% slope efficiency is constructed.

  12. TOPAZ II System Thermal Management During Prelaunch and Orbital Insertion

    NASA Astrophysics Data System (ADS)

    Ogloblin, Boris; Nikitin, Vladimir; Luppov, Alexi; Kirillov, E. Ya.; Bocharov, Anatoly; Polansky, Gary; Reynolds, Edward

    1994-07-01

    For space nuclear power systems that use liquid metal coolants, it is important to prevent the coolant from freezing prior to the start-up of the reactor in space. For the original mission of the Topaz II, this would be achieved with a combination of (1) prelaunch electric heating of the liquid metal combined with coolant circulation, (2) a thermal cover to reduce the heat loss during the orbital insertion mission phase and (3) periodic circulation of the coolant during the orbital insertion mission phase to transfer heat from the warmer structures of the reactor to those most prone to freezing. Because the currently proposed Topaz II mission differs significantly from the original mission this scheme was re-evaluated. For the new mission the prelaunch heating could be simplified by merely circulating 300 K air over the reactor system and eliminating power to the electric heaters and the electromagnetic pump through the onboard detachable connector.

  13. Experimental study of an air-cooled thermal management system for high capacity lithium-titanate batteries

    NASA Astrophysics Data System (ADS)

    Giuliano, Michael R.; Prasad, Ajay K.; Advani, Suresh G.

    2012-10-01

    Lithium-titanate batteries have become an attractive option for battery electric vehicles and hybrid electric vehicles. In order to maintain safe operating temperatures, these batteries must be actively cooled during operation. Liquid-cooled systems typically employed for this purpose are inefficient due to the parasitic power consumed by the on-board chiller unit and the coolant pump. A more efficient option would be to circulate ambient air through the battery bank and directly reject the heat to the ambient. We designed and fabricated such an air-cooled thermal management system employing metal-foam based heat exchanger plates for sufficient heat removal capacity. Experiments were conducted with Altairnano's 50 Ah cells over a range of charge-discharge cycle currents at two air flow rates. It was found that an airflow of 1100 mls-1 per cell restricts the temperature rise of the coolant air to less than 10 °C over ambient even for 200 A charge-discharge cycles. Furthermore, it was shown that the power required to drive the air through the heat exchanger was less than a conventional liquid-cooled thermal management system. The results indicate that air-cooled systems can be an effective and efficient method for the thermal management of automotive battery packs.

  14. GRID based Thermal Images Processing for volcanic activity monitoring

    NASA Astrophysics Data System (ADS)

    Mangiagli, S.; Coco, S.; Drago, L.; Laudani, A.,; Lodato, L.; Pollicino, G.; Torrisi, O.

    2009-04-01

    Since 2001, the Catania Section of the National Institute of Geophysics and Volcanology (INGV) has been running the video stations recording the volcanic activity of Mount Etna, Stromboli and the Fossa Crater of Vulcano island. The video signals of 11 video cameras (seven operating in the visible band and four in infrared) are sent in real time to INGV Control Centre where they are visualized on monitors and archived on a dedicated NAS storage. The video surveillance of the Sicilian volcanoes, situated near to densely populated areas, helps the volcanologists providing the Civil Protection authorities with updates in real time on the on-going volcanic activity. In particular, five video cameras are operating on Mt. Etna and they record the volcano from the south and east sides 24 hours a day. During emergencies, mobile video stations may also be used to better film the most important phases of the activity. Single shots are published on the Catania Section intranet and internet websites. On June 2006 a A 40 thermal camera was installed in Vulcano La Fossa Crater. The location was in the internal and opposite crater flank (S1), 400 m distant from the fumarole field. The first two-year of data on temperature distribution frequency were recorded with this new methodology of acquisition, and automatically elaborated by software at INGV Catania Section. In fact a dedicated software developed in IDL, denominated Volcano Thermo Analysis (VTA), was appositely developed in order to extract a set of important features, able to characterize with a good approssimation the volcanic activity. In particular the program first load and opportunely convert the thermal images, then according to the Region Of Interest (ROI) and the temperature ranges defined by the user provide to automatic spatial and statistic analysis. In addition the VTA is able to analysis all the temporal series of images available in order to achieve the time-event analysis and the dynamic of the volcanic

  15. A latchable thermally activated phase change actuator for microfluidic systems

    NASA Astrophysics Data System (ADS)

    Richter, Christiane; Sachsenheimer, Kai; Rapp, Bastian E.

    2016-03-01

    Complex microfluidic systems often require a high number of individually controllable active components like valves and pumps. In this paper we present the development and optimization of a latchable thermally controlled phase change actuator which uses a solid/liquid phase transition of a phase change medium and the displacement of the liquid phase change medium to change and stabilize the two states of the actuator. Because the phase change is triggered by heat produced with ohmic resistors the used control signal is an electrical signal. In contrast to pneumatically activated membrane valves this concept allows the individual control of several dozen actuators with only two external pressure lines. Within this paper we show the general working principle of the actuator and demonstrate its general function and the scalability of the concept at an example of four actuators. Additionally we present the complete results of our studies to optimize the response behavior of the actuator - the influence of the heating power as well as the used phase change medium on melting and solidifying times.

  16. Feasibility of culvert IED detection using thermal neutron activation

    NASA Astrophysics Data System (ADS)

    Faust, Anthony A.; McFee, John E.; Clifford, Edward T. H.; Andrews, Hugh Robert; Mosquera, Cristian; Roberts, William C.

    2012-06-01

    Bulk explosives hidden in culverts pose a serious threat to the Canadian and allied armies. Culverts provide an opportunity to conceal insurgent activity, avoid the need for detectable surface disturbances, and limit the applicability of conventional sub-surface sensing techniques. Further, in spite of the large masses of explosives that can be employed, the large sensor{target separation makes detection of the bulk explosive content challeng- ing. Defence R&D Canada { Sueld and Bubble Technology Industries have been developing thermal neutron activation (TNA) sensors for detection of buried bulk explosives for over 15 years. The next generation TNA sensor, known as TNA2, incorporates a number of improvements that allow for increased sensor-to-target dis- tances, making it potentially feasible to detect large improvised explosive devices (IEDs) in culverts using TNA. Experiments to determine the ability of TNA2 to detect improvised explosive devices in culverts are described, and the resulting signal levels observed for relevant quantities of explosives are presented. Observations conrm that bulk explosives detection using TNA against a culvert-IED is possible, with large charges posing a detection challenge at least as dicult as that of a deeply buried anti-tank landmine. Because of the prototype nature of the TNA sensor used, it is not yet possible to make denitive statements about the absolute sensitivity or detection time. Further investigation is warranted.

  17. Synthesis, thermal stability, and photocatalytic activity of nanocrystalline titanium carbide

    SciTech Connect

    Chen, Youjian; Zhang, Hong; Ma, DeKun; Ma, Jianhua; Ye, Hongnan; Qian, Gaojin; Ye, Yi

    2011-11-15

    Highlights: {yields} The synthesized temperature is lower than some conventional methods. {yields} These raw materials are safe; all manipulations are rather safe and convenient. {yields} The product exhibits photocatalytic activity in degradation of Rhodamine-B. -- Abstract: Titanium carbide (TiC) was prepared via one simple route by the reaction of metallic magnesium powders with titanium dioxide (TiO{sub 2}) and potassium acetate (CH{sub 3}COOK) in an autoclave at 600 {sup o}C and 8 h. Phase structure and morphology were characterized by X-ray powder diffraction (XRD) and Scanning electron microscopy (SEM). The results indicated that the product was cubic TiC, which consisted of particles with an average size of about 100 nm in diameter. The product was also studied by the thermogravimetric analysis (TGA) and its photocatalysis. It had good thermal stability and oxidation resistance below 350 {sup o}C in air. In addition, we discovered that the cubic TiC powders exhibited photocatalytic activity in degradation of Rhodamine-B (RhB) under 500 W mercury lamp light irradiation.

  18. Thermally activated delayed fluorescence materials towards the breakthrough of organoelectronics.

    PubMed

    Tao, Ye; Yuan, Kai; Chen, Ting; Xu, Peng; Li, Huanhuan; Chen, Runfeng; Zheng, Chao; Zhang, Lei; Huang, Wei

    2014-12-17

    The design and characterization of thermally activated delayed fluorescence (TADF) materials for optoelectronic applications represents an active area of recent research in organoelectronics. Noble metal-free TADF molecules offer unique optical and electronic properties arising from the efficient transition and interconversion between the lowest singlet (S1 ) and triplet (T1 ) excited states. Their ability to harvest triplet excitons for fluorescence through facilitated reverse intersystem crossing (T1 →S1 ) could directly impact their properties and performances, which is attractive for a wide variety of low-cost optoelectronic devices. TADF-based organic light-emitting diodes, oxygen, and temperature sensors show significantly upgraded device performances that are comparable to the ones of traditional rare-metal complexes. Here we present an overview of the quick development in TADF mechanisms, materials, and applications. Fundamental principles on design strategies of TADF materials and the common relationship between the molecular structures and optoelectronic properties for diverse research topics and a survey of recent progress in the development of TADF materials, with a particular emphasis on their different types of metal-organic complexes, D-A molecules, and fullerenes, are highlighted. The success in the breakthrough of the theoretical and technical challenges that arise in developing high-performance TADF materials may pave the way to shape the future of organoelectronics. PMID:25230116

  19. Towards AlN optical cladding layers for thermal management in hybrid lasers

    NASA Astrophysics Data System (ADS)

    Mathews, Ian; Lei, Shenghui; Nolan, Kevin; Levaufre, Guillaume; Shen, Alexandre; Duan, Guang-Hua; Corbett, Brian; Enright, Ryan

    2015-06-01

    Aluminium Nitride (AlN) is proposed as a dual function optical cladding and thermal spreading layer for hybrid ridge lasers, replacing current benzocyclobutene (BCB) encapsulation. A high thermal conductivity material placed in intimate contact with the Multi-Quantum Well active region of the laser allows rapid heat removal at source but places a number of constraints on material selection. AlN is considered the most suitable due to its high thermal conductivity when deposited at low deposition temperatures, similar co-efficient of thermal expansion to InP, its suitable refractive index and its dielectric nature. We have previously simulated the possible reduction in the thermal resistance of a hybrid ridge laser by replacing the BCB cladding material with a material of higher thermal conductivity of up to 319 W/mK. Towards this goal, we demonstrate AlN thin-films deposited by reactive DC magnetron sputtering on InP.

  20. Improved thermal neutron activation sensor for detection of bulk explosives

    NASA Astrophysics Data System (ADS)

    McFee, John E.; Faust, Anthony A.; Andrews, H. Robert; Clifford, Edward T. H.; Mosquera, Cristian M.

    2012-06-01

    Defence R&D Canada - Suffield and Bubble Technology Industries have been developing thermal neutron activation (TNA) sensors for detection of buried bulk explosives since 1994. First generation sensors, employing an isotopic source and NaI(Tl) gamma ray detectors, were deployed by Canadian Forces in 2002 as confirmation sensors on the ILDS teleoperated, vehicle-mounted, multi-sensor anti-tank landmine detection systems. The first generation TNA could detect anti-tank mines buried 10 cm or less in no more than a minute, but deeper mines and those significantly displaced horizontally required considerably longer times. Mines as deep as 30 cm could be detected with long counting times (1000 s). The second generation TNA detector is being developed with a number of improvements aimed at increasing sensitivity and facilitating ease of operation. Among these are an electronic neutron generator to increase sensitivity for deeper and horizontally displaced explosives; LaBr3(Ce) scintillators, to improve time response and energy resolution; improved thermal and electronic stability; improved sensor head geometry to minimize spatial response nonuniformity; and more robust data processing. This improved sensitivity can translate to either decreased counting times, decreased minimum detectable explosive quantities, increased maximum sensor-to-target displacement, or a trade off among all three. Experiments to characterize the performance of the latest generation TNA in detecting buried landmines and IEDs hidden in culverts were conducted during 2011. This paper describes the second generation system. The experimental setup and methodology are detailed and preliminary comparisons between the performance of first and second generation systems are presented.

  1. Shuttle active thermal control system development testing. Volume 1: Overall summary

    NASA Technical Reports Server (NTRS)

    Howell, H. R.

    1974-01-01

    A summary is given of a series of thermal vacuum tests designed to support the development of the orbiter active thermal control system (ATCS) and included testing of a wide heat load range modular radiator system (MRS) configured to the March 1973 orbiter baseline system, a candidate weight reducing radiator/water cooling system, and a smaller radiator system with a high performance radiator coating. The tests verified the performance of the baseline system and obtained detailed design information for application of a wide heat load range modular radiator system to the orbiter. The two candidate ATCS weight reducing designs have undergone extensive concept verification testing and their system operating characteristics have been determined in sufficient detail for application to the orbiter. Design information has been obtained for an integrated radiator/water cooling system that provides for vehicle heat rejection as well as water management of the excess fuel cell water. Processing techniques have been developed and verified for the application of a high performance thermal control coating to large radiator areas subjected to a temperature range of -280 F to +160 F.

  2. Implementation of Active Thermal Control (ATC) for the Soil Moisture Active and Passive (SMAP) Radiometer

    NASA Technical Reports Server (NTRS)

    Mikhaylov, Rebecca; Kwack, Eug; French, Richard; Dawson, Douglas; Hoffman, Pamela

    2014-01-01

    NASA's Earth Observing Soil Moisture Active and Passive (SMAP) Mission is scheduled to launch in November 2014 into a 685 kilometer near-polar, sun-synchronous orbit. SMAP will provide comprehensive global mapping measurements of soil moisture and freeze/thaw state in order to enhance understanding of the processes that link the water, energy, and carbon cycles. The primary objectives of SMAP are to improve worldwide weather and flood forecasting, enhance climate prediction, and refine drought and agriculture monitoring during its three year mission. The SMAP instrument architecture incorporates an L-band radar and an L-band radiometer which share a common feed horn and parabolic mesh reflector. The instrument rotates about the nadir axis at approximately 15 revolutions per minute, thereby providing a conically scanning wide swath antenna beam that is capable of achieving global coverage within three days. In order to make the necessary precise surface emission measurements from space, the electronics and hardware associated with the radiometer must meet tight short-term (instantaneous and orbital) and long-term (monthly and mission) thermal stabilities. Maintaining these tight thermal stabilities is quite challenging because the sensitive electronics are located on a fast spinning platform that can either be in full sunlight or total eclipse, thus exposing them to a highly transient environment. A passive design approach was first adopted early in the design cycle as a low-cost solution. With careful thermal design efforts to cocoon and protect all sensitive components, all stability requirements were met passively. Active thermal control (ATC) was later added after the instrument Preliminary Design Review (PDR) to mitigate the threat of undetected gain glitches, not for thermal-stability reasons. Gain glitches are common problems with radiometers during missions, and one simple way to avoid gain glitches is to use the in-flight set point programmability that ATC

  3. Fuel Cell Thermal Management Through Conductive Cooling Plates

    NASA Technical Reports Server (NTRS)

    Colozza, Anthony J.; Burke, Kenneth A.

    2008-01-01

    An analysis was performed to evaluate the concept of utilizing conductive cooling plates to remove heat from a fuel cell stack, as opposed to a conventional internal cooling loop. The potential advantages of this type of cooling system are reduced stack complexity and weight and increased reliability through the reduction of the number of internal fluid seals. The conductive cooling plates would extract heat from the stack transferring it to an external coolant loop. The analysis was performed to determine the required thickness of these plates. The analysis was based on an energy balance between the thermal energy produced within the stack and the heat removal from the cooling plates. To accomplish the energy balance, the heat flow into and along the plates to the cooling fluid was modeled. Results were generated for various numbers of cells being cooled by a single cooling plate. The results provided cooling plate thickness, mass, and operating temperature of the plates. It was determined that utilizing high-conductivity pyrolitic graphite cooling plates can provide a specific cooling capacity (W/kg) equivalent to or potentially greater than a conventional internal cooling loop system.

  4. Modeling thermal management of lithium-ion PNGV batteries

    NASA Astrophysics Data System (ADS)

    Nelson, Paul; Dees, Dennis; Amine, Khalil; Henriksen, Gary

    Batteries were designed with the aid of a computer modeling program to study the requirements of the thermal control system for meeting the goals set by the Partnership for a New Generation of Vehicles (PNGV). The battery designs were based upon the lithium-ion cell composition designated Gen-2 in the US Department of Energy Advanced Technology Development Program. The worst-case cooling requirement that would occur during prolonged aggressive driving was estimated to be 250 W or about 5 W per cell for a 48-cell battery. Rapid heating of the battery from a very low startup temperature is more difficult than cooling during driving. A dielectric transformer fluid is superior to air for both heating and cooling the battery. A dedicated refrigeration system for cooling the battery coolant would be helpful in maintaining low temperature during driving. The use of ample insulation would effectively slow the battery temperature rise when parking the vehicle in warm weather. Operating the battery at 10 °C during the first several years when the battery has excess power would extend the battery life.

  5. Thermo-mechanical properties of carbon nanotubes and applications in thermal management

    NASA Astrophysics Data System (ADS)

    Nguyen, Manh Hong; Thang Bui, Hung; Trinh Pham, Van; Phan, Ngoc Hong; Nguyen, Tuan Hong; Chuc Nguyen, Van; Quang Le, Dinh; Khoi Phan, Hong; Phan, Ngoc Minh

    2016-06-01

    Thanks to their very high thermal conductivity, high Young’s modulus and unique tensile strength, carbon nanotubes (CNTs) have become one of the most suitable nano additives for heat conductive materials. In this work, we present results obtained for the synthesis of heat conductive materials containing CNT based thermal greases, nanoliquids and lubricating oils. These synthesized heat conductive materials were applied to thermal management for high power electronic devices (CPUs, LEDs) and internal combustion engines. The simulation and experimental results on thermal greases for an Intel Pentium IV processor showed that the thermal conductivity of greases increases 1.4 times and the saturation temperature of the CPU decreased by 5 °C by using thermal grease containing 2 wt% CNTs. Nanoliquids containing CNT based distilled water/ethylene glycol were successfully applied in heat dissipation for an Intel Core i5 processor and a 450 W floodlight LED. The experimental results showed that the saturation temperature of the Intel Core i5 processor and the 450 W floodlight LED decreased by about 6 °C and 3.5 °C, respectively, when using nanoliquids containing 1 g l‑1 of CNTs. The CNTs were also effectively utilized additive materials for the synthesis of lubricating oils to improve the thermal conductivity, heat dissipation efficiency and performance efficiency of engines. The experimental results show that the thermal conductivity of lubricating oils increased by 12.5%, the engine saved 15% fuel consumption, and the longevity of the lubricating oil increased up to 20 000 km by using 0.1% vol. CNTs in the lubricating oils. All above results have confirmed the tremendous application potential of heat conductive materials containing CNTs in thermal management for high power electronic devices, internal combustion engines and other high power apparatus.

  6. Fuel injector utilizing non-thermal plasma activation

    SciTech Connect

    Coates, Don M.; Rosocha, Louis A.

    2009-12-01

    A non-thermal plasma assisted combustion fuel injector that uses an inner and outer electrode to create an electric field from a high voltage power supply. A dielectric material is operatively disposed between the two electrodes to prevent arcing and to promote the formation of a non-thermal plasma. A fuel injector, which converts a liquid fuel into a dispersed mist, vapor, or aerosolized fuel, injects into the non-thermal plasma generating energetic electrons and other highly reactive chemical species.

  7. New latent heat storage system with nanoparticles for thermal management of electric vehicles

    NASA Astrophysics Data System (ADS)

    Javani, N.; Dincer, I.; Naterer, G. F.

    2014-12-01

    In this paper, a new passive thermal management system for electric vehicles is developed. A latent heat thermal energy storage with nanoparticles is designed and optimized. A genetic algorithm method is employed to minimize the length of the heat exchanger tubes. The results show that even the optimum length of a shell and tube heat exchanger becomes too large to be employed in a vehicle. This is mainly due to the very low thermal conductivity of phase change material (PCM) which fills the shell side of the heat exchanger. A carbon nanotube (CNT) and PCM mixture is then studied where the probability of nanotubes in a series configuration is defined as a deterministic design parameter. Various heat transfer rates, ranging from 300 W to 600 W, are utilized to optimize battery cooling options in the heat exchanger. The optimization results show that smaller tube diameters minimize the heat exchanger length. Furthermore, finned tubes lead to a higher heat exchanger length due to more heat transfer resistance. By increasing the CNT concentration, the optimum length of the heat exchanger decreases and makes the improved thermal management system a more efficient and competitive with air and liquid thermal management systems.

  8. Graphene-Based Hybrid Composites for Efficient Thermal Management of Electronic Devices.

    PubMed

    Shtein, Michael; Nadiv, Roey; Buzaglo, Matat; Regev, Oren

    2015-10-28

    Thermal management has become a critical aspect in next-generation miniaturized electronic devices. Efficient heat dissipation reduces their operating temperatures and insures optimal performance, service life, and efficacy. Shielding against shocks, vibrations, and moisture is also imperative when the electronic circuits are located outdoors. Potting (or encapsulating) them in polymer-based composites with enhanced thermal conductivity (TC) may provide a solution for both thermal management and shielding challenges. In the current study, graphene is employed as a filler to fabricate composites with isotropic ultrahigh TC (>12 W m(-1) K(-1)) and good mechanical properties (>30 MPa flexural and compressive strength). To avoid short-circuiting the electronic assemblies, a dispersion of secondary ceramic-based filler reduces the electrical conductivity and synergistically enhances the TC of composites. When utilized as potting materials, these novel hybrid composites effectively dissipate the heat from electronic devices; their operating temperatures decrease from 110 to 37 °C, and their effective thermal resistances are drastically reduced, by up to 90%. The simple filler dispersion method and the precise manipulation of the composite transport properties via hybrid filling offer a universal approach to the large-scale production of novel materials for thermal management and other applications. PMID:26445279

  9. Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

    NASA Technical Reports Server (NTRS)

    Emrich, William J., Jr.

    2014-01-01

    Over the past year the Nuclear Thermal Rocket Element Environmental Simulator (NTREES) has been undergoing a significant upgrade beyond its initial configuration. The NTREES facility is designed to perform realistic non-nuclear testing of nuclear thermal rocket (NTR) fuel elements and fuel materials. Although the NTREES facility cannot mimic the neutron and gamma environment of an operating NTR, it can simulate the thermal hydraulic environment within an NTR fuel element to provide critical information on material performance and compatibility. The first phase of the upgrade activities which was completed in 2012 in part consisted of an extensive modification to the hydrogen system to permit computer controlled operations outside the building through the use of pneumatically operated variable position valves. This setup also allows the hydrogen flow rate to be increased to over 200 g/sec and reduced the operation complexity of the system. The second stage of modifications to NTREES which has just been completed expands the capabilities of the facility significantly. In particular, the previous 50 kW induction power supply has been replaced with a 1.2 MW unit which should allow more prototypical fuel element temperatures to be reached. The water cooling system was also upgraded to so as to be capable of removing 100% of the heat generated during. This new setup required that the NTREES vessel be raised onto a platform along with most of its associated gas and vent lines. In this arrangement, the induction heater and water systems are now located underneath the platform. In this new configuration, the 1.2 MW NTREES induction heater will be capable of testing fuel elements and fuel materials in flowing hydrogen at pressures up to 1000 psi at temperatures up to and beyond 3000 K and at near-prototypic reactor channel power densities. NTREES is also capable of testing potential fuel elements with a variety of propellants, including hydrogen with additives to inhibit

  10. Potential and challenges in use of thermal imaging for humid region irrigation system management

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Thermal imaging has shown potential to assist with many aspects of irrigation management including scheduling water application, detecting leaky irrigation canals, and gauging the overall effectiveness of water distribution networks used in furrow irrigation. Many challenges exist for the use of the...

  11. DEMONSTRATION BULLETIN: X*TRAX MODEL 200 THERMAL DESORPTION SYSTEMS - CHEMICAL WASTE MANAGEMENT, INC.

    EPA Science Inventory

    The X*TRAX™ Mode! 200 Thermal Desorption System developed by Chemical Waste Management, Inc. (CWM), is a low-temperature process designed to separate organic contaminants from soils, sludges, and other solid media. The X*TRAX™ Model 200 is fully transportable and consists of thre...

  12. Thermal Management of Batteries in Advanced Vehicles Using Phase-Change Materials (Presentation)

    SciTech Connect

    Kim, G.-H.; Gonder, J.; Lustbader, J.; Pesaran, A.

    2007-12-01

    This Powerpoint presentation examines battery thermal management using PCM and concludes excellent performance in limiting peak temperatures at short period extensive battery use; although, vehicle designers will need to weigh the potential increase in mass and cost associated with adding PCM against the anticipated benefits.

  13. The thermal origin of spontaneous activity in the Limulus photoreceptor

    PubMed Central

    Srebro, Richard; Behbehani, Mahmood

    1972-01-01

    1. Discrete depolarizations of the photoreceptor cell membrane called discrete waves occur spontaneously and in response to illumination in the eye of the horseshoe crab, Limulus. Each light induced discrete wave is caused by the absorption of a single photon. 2. The frequencies of spontaneous and light induced discrete waves were studied at different temperatures from 0 to 25° C using a new method of counting them to avoid errors due to their temporal overlap. 3. The frequency of spontaneous discrete waves followed the Arrhenius relationship with activation energy equal to 48·6 kcal. 4. The frequency of the discrete waves caused by a fixed level of steady illumination was not significantly changed when the temperature of the cell was changed. 5. The relationship of the frequency of spontaneous discrete waves to temperature was compared to a prediction based on the relationship of the quantum relative spectral sensitivity of the Limulus eye to the temperature of the eye. The prediction was in good agreement with observation and suggests that spontaneous discrete waves result from thermally induced cis to trans isomerizations of visual pigment molecules. PMID:5071400

  14. Characterization of AN Actively Cooled Metal Foil Thermal Radiation Shield

    NASA Astrophysics Data System (ADS)

    Feller, J. R.; Kashani, A.; Helvensteijn, B. P. M.; Salerno, L. J.

    2010-04-01

    Zero boil-off (ZBO) or reduced boil-off (RBO) systems that involve active cooling of large cryogenic propellant tanks will most likely be required for future space exploration missions. For liquid oxygen or methane, such systems could be implemented using existing high technology readiness level (TRL) cryocoolers. However, for liquid hydrogen temperatures (˜20 K) no such coolers exist. In order to partially circumvent this technology gap, the concept of broad area cooling (BAC) has been developed, whereby a low mass thermal radiation shield could be maintained at temperatures around 100 K by steady circulation of cold pressurized gas through a network of narrow tubes. By this method it is possible to dramatically reduce the radiative heat leak to the 20 K tank. A series of experiments, designed to investigate the heat transfer capabilities of BAC systems, have been conducted at NASA Ames Research Center (ARC). Results of the final experiment in this series, investigating heat transfer from a metal foil film to a distributed cooling line, are presented here.

  15. CHARACTERIZATION OF AN ACTIVELY COOLED METAL FOIL THERMAL RADIATION SHIELD

    SciTech Connect

    Feller, J. R.; Salerno, L. J.; Kashani, A.; Helvensteijn, B. P. M.

    2010-04-09

    Zero boil-off (ZBO) or reduced boil-off (RBO) systems that involve active cooling of large cryogenic propellant tanks will most likely be required for future space exploration missions. For liquid oxygen or methane, such systems could be implemented using existing high technology readiness level (TRL) cryocoolers. However, for liquid hydrogen temperatures (approx20 K) no such coolers exist. In order to partially circumvent this technology gap, the concept of broad area cooling (BAC) has been developed, whereby a low mass thermal radiation shield could be maintained at temperatures around 100 K by steady circulation of cold pressurized gas through a network of narrow tubes. By this method it is possible to dramatically reduce the radiative heat leak to the 20 K tank. A series of experiments, designed to investigate the heat transfer capabilities of BAC systems, have been conducted at NASA Ames Research Center (ARC). Results of the final experiment in this series, investigating heat transfer from a metal foil film to a distributed cooling line, are presented here.

  16. Ultrasound assisted, thermally activated persulfate oxidation of coal tar DNAPLs.

    PubMed

    Peng, Libin; Wang, Li; Hu, Xingting; Wu, Peihui; Wang, Xueqing; Huang, Chumei; Wang, Xiangyang; Deng, Dayi

    2016-11-15

    The feasibility of ultrasound assisted, thermally activated persulfate for effective oxidation of twenty 2-6 ringed coal tar PAHs in a biphasic tar/water system and a triphasic tar/soil/water system were investigated and established. The results indicate that ultrasonic assistance, persulfate and elevated reaction temperature are all required to achieve effective oxidation of coal tar PAHs, while the heating needed can be provided by ultrasonic induced heating as well. Further kinetic analysis reveals that the oxidation of individual PAH in the biphasic tar/water system follows the first-order kinetics, and individual PAH oxidation rate is primary determined by the mass transfer coefficients, tar/water interfacial areas, the aqueous solubility of individual PAH and its concentration in coal tar. Based on the kinetic analysis and experimental results, the contributions of ultrasound, persulfate and elevated reaction temperature to PAHs oxidation were characterized, and the effects of ultrasonic intensity and oxidant dosage on PAHs oxidation efficiency were investigated. In addition, the results indicate that individual PAH degradability is closely related to its reactivity as well, and the high reactivity of 4-6 ringed PAHs substantially improves their degradability. PMID:27450342

  17. Thermal activation of superheated lipid-coated perfluorocarbon drops.

    PubMed

    Mountford, Paul A; Thomas, Alec N; Borden, Mark A

    2015-04-28

    This study explored the thermal conditions necessary for the vaporization of superheated perfluorocarbon nanodrops. Droplets C3F8 and C4F10 coated with a homologous series of saturated diacylphosphatidylcholines were formed by condensation of 4 μm diameter microbubbles. These drops were stable at room temperature and atmospheric pressure, but they vaporized back into microbubbles at higher temperatures. The vaporization transition was measured as a function of temperature by laser light extinction. We found that C3F8 and C4F10 drops experienced 90% vaporization at 40 and 75 °C, respectively, near the theoretical superheat limits (80-90% of the critical temperature). We therefore conclude that the metastabilty of these phase-change agents arises not from the droplet Laplace pressure altering the boiling point, as previously reported, but from the metastability of the pure superheated fluid to homogeneous nucleation. The rate of C4F10 drop vaporization was quantified at temperatures ranging from 55 to 75 °C, and an apparent activation energy barrier was calculated from an Arrhenius plot. Interestingly, the activation energy increased linearly with acyl chain length from C14 to C20, indicating that lipid interchain cohesion plays an important role in suppressing the vaporization rate. The vaporized drops (microbubbles) were found to be unstable to dissolution at high temperatures, particularly for C14 and C16. However, proper choice of the fluorocarbon and lipid species provided a nanoemulsion that could undergo at least ten reversible condensation/vaporization cycles. The vaporization properties presented in this study may facilitate the engineering of tunable phase-shift particles for diagnostic imaging, targeted drug delivery, tissue ablation, and other applications. PMID:25853278

  18. Thermal Protection System Imagery Inspection Management System -TIIMS

    NASA Technical Reports Server (NTRS)

    Goza, Sharon; Melendrez, David L.; Henningan, Marsha; LaBasse, Daniel; Smith, Daniel J.

    2011-01-01

    TIIMS is used during the inspection phases of every mission to provide quick visual feedback, detailed inspection data, and determination to the mission management team. This system consists of a visual Web page interface, an SQL database, and a graphical image generator. These combine to allow a user to ascertain quickly the status of the inspection process, and current determination of any problem zones. The TIIMS system allows inspection engineers to enter their determinations into a database and to link pertinent images and video to those database entries. The database then assigns criteria to each zone and tile, and via query, sends the information to a graphical image generation program. Using the official TIPS database tile positions and sizes, the graphical image generation program creates images of the current status of the orbiter, coloring zones, and tiles based on a predefined key code. These images are then displayed on a Web page using customized JAVA scripts to display the appropriate zone of the orbiter based on the location of the user's cursor. The close-up graphic and database entry for that particular zone can then be seen by selecting the zone. This page contains links into the database to access the images used by the inspection engineer when they make the determination entered into the database. Status for the inspection zones changes as determinations are refined and shown by the appropriate color code.

  19. Active Dust Mitigation Technology for Thermal Radiators for Lunar Exploration

    NASA Technical Reports Server (NTRS)

    Calle, C. I.; Buhler, C. R.; Hogue, M. D.; Johansen, M. R.; Hopkins, J. W.; Holloway, N. M. H.; Connell, J. W.; Chen, A.; Irwin, S. A.; Case, S. O.; VanSuetendael, N. J.; Snyder, S. J.; Clements, J. S.

    2010-01-01

    Dust accumulation on thermal radiator surfaces planned for lunar exploration will significantly reduce their efficiency. Evidence from the Apollo missions shows that an insulating layer of dust accumulated on radiator surfaces could not be removed and caused serious thermal control problems. Temperatures measured at different locations in the magnetometer on Apollo 12 were 38 C warmer than expected due to lunar dust accumulation. In this paper, we report on the application of the Electrodynamic Dust Shield (EDS) technology being developed in our NASA laboratory and applied to thermal radiator surfaces. The EDS uses electrostatic and dielectrophoretic forces generated by a grid of electrodes running a 2 micro A electric current to remove dust particles from surfaces. Working prototypes of EDS systems on solar panels and on thermal radiators have been successfully developed and tested at vacuum with clearing efficiencies above 92%. For this work EDS prototypes on flexible and rigid thermal radiators were developed and tested at vacuum.

  20. High diversity stabilizes the thermal resilience of pollinator communities in intensively managed grasslands.

    PubMed

    Kühsel, Sara; Blüthgen, Nico

    2015-01-01

    The resilience of ecosystems depends on the diversity of species and their specific responses to environmental variation. Here we show that the diversity of climatic responses across species contributes to a higher projected resilience of species-rich pollinator communities in real-world ecosystems despite land-use intensification. We determined the thermal niche of 511 pollinator species (flies, bees, beetles and butterflies) in 40 grasslands. Species in intensively used grasslands have broader thermal niches and are also more complementary in their thermal optima. The observed increase in thermal resilience with land-use intensification is mainly driven by the dominant flies that prefer cooler temperatures and compensate for losses of other taxa. Temperature explained 84% of the variation in pollinator activity across species and sites. Given the key role of temperature, quantifying the diversity of thermal responses within functional groups is a promising approach to assess the vulnerability of ecosystems to land-use intensification and climate change. PMID:26258282

  1. High diversity stabilizes the thermal resilience of pollinator communities in intensively managed grasslands

    PubMed Central

    Kühsel, Sara; Blüthgen, Nico

    2015-01-01

    The resilience of ecosystems depends on the diversity of species and their specific responses to environmental variation. Here we show that the diversity of climatic responses across species contributes to a higher projected resilience of species-rich pollinator communities in real-world ecosystems despite land-use intensification. We determined the thermal niche of 511 pollinator species (flies, bees, beetles and butterflies) in 40 grasslands. Species in intensively used grasslands have broader thermal niches and are also more complementary in their thermal optima. The observed increase in thermal resilience with land-use intensification is mainly driven by the dominant flies that prefer cooler temperatures and compensate for losses of other taxa. Temperature explained 84% of the variation in pollinator activity across species and sites. Given the key role of temperature, quantifying the diversity of thermal responses within functional groups is a promising approach to assess the vulnerability of ecosystems to land-use intensification and climate change. PMID:26258282

  2. Self-adaptive thermal management - the fundamentals and applications in Li-polymer batteries

    NASA Astrophysics Data System (ADS)

    Geng, Xiaobao

    The thermal management systems for electronic devices and their power sources are facing increasing challenge to accommodate the ever-changing environmental and operational conditions. The conventional thermal management systems, with a predominant focus on cooling, are often not sufficient in those cases. In addition, to support miniaturization, complex systems and broader applications (e.g., space and military), the thermal management system often needs to be compatible with smaller device and their fabrication processes, dissipate heat efficiently for localized heat spot, and meet the requirement of light weight and low power consumption. In order to address such issues, a self-adaptive thermal switch array (TSA) is proposed based on microelectromechanical systems (MEMS) technology which has the capability automatically change its thermal conductance according to the environmental and operational conditions. This TSA was actuated by low melting alloy (LMA) with neither control unit nor parasitic energy consumption. The idea has been first demonstrated by a prototype device with the stabilization temperatures under various power inputs investigated both experimentally and theoretically. When the power input was changed from 3.8W to 5.8W, the stabilization temperature of the device was increased only by 2.5°C due to the stabilization effect of TSA. The experimental data were found in good agreement with their theoretical value. Based on the theoretical model, two types of TSA, namely high-on and low-off, were further developed to increase on-state thermal conductance and decrease off-state thermal conductance, respectively. Compared with the low-off TSA, the high-on TSA can more efficiently cool the devices and stabilize their temperature at a value closer to the melting point of LMA even under higher power inputs. On the other hand, the startup time and energy consumption were significantly reduced with the low-off TSA design due to the enhanced off

  3. Tracheostomy in the management of patients with thermal injuries

    PubMed Central

    Mourelo, Mónica; Galeiras, Rita; Pértega, Sonia; Freire, David; López, Eugenia; Broullón, Javier; Campos, Eva

    2015-01-01

    Objective: To assess the use and clinical impact of tracheostomy in burn patients. Summary Background Data: The role of tracheostomy in the management of burn patients is controversial, with only a few recent studies conducted in this population. Methods: Retrospective study of all adult burn patients who underwent a tracheostomy in a Burns Unit between 1995 and 2013. These were compared with a control group (1:1) who underwent orotracheal intubation. Hospital records were reviewed to obtain demographic and clinical information, including those related to respiratory support and tracheostomy. The McNemar's Chi-square and Signed-Rank Tests were used to study differences in morbimortality between both groups. Results: A total of n = 20 patients underwent tracheostomy (0.9% of admissions, 56.0 ± 19.5 years, 60.0% women). The most common indication was long-term ventilation (75%), 24.6 ± 19.7 days after admission. Thirteen patients were successfully decannulated with a fatal complication observed in one case. Patients in the tracheostomy group were found to require longer-term mechanical ventilation (43.2 vs. 20.4 days; P = 0.004), with no differences in respiratory infection rates (30.0% vs. 31.6%; P = 0.687) or mortality (30.0% vs. 42.1%; P = 0.500). Ventilator weaning times (15.7 vs. 3.3 days; P = 0.001) and hospital stays (99.1 vs. 53.1 days; P = 0.030) were longer in the tracheostomy group, with no differences in duration of sedation. Conclusions: Tracheostomy may be a safe procedure in burn patients and is not associated with higher rates of mortality or respiratory infection. Tracheostomy patients showed longer mechanical ventilation times and higher morbidity, probably not attributable to tracheostomy. PMID:26321803

  4. Idaho Senior Center Activities, Activity Participation Level, and Managers' Perceptions of Activity Success.

    ERIC Educational Resources Information Center

    Girvan, James T.; Harris, Frances

    A survey completed by managers of 77 senior centers in Idaho revealed that meals, blood pressure screening, and games and trips were the most successful activities offered. Alzheimer's support groups, library books for loan, and exercise classes were the least successful. Possible reasons for the success or failure of these activities were…

  5. Advanced deposition model for thermal activated chemical vapor deposition

    NASA Astrophysics Data System (ADS)

    Cai, Dang

    Thermal Activated Chemical Vapor Deposition (TACVD) is defined as the formation of a stable solid product on a heated substrate surface from chemical reactions and/or dissociation of gaseous reactants in an activated environment. It has become an essential process for producing solid film, bulk material, coating, fibers, powders and monolithic components. Global market of CVD products has reached multi billions dollars for each year. In the recent years CVD process has been extensively used to manufacture semiconductors and other electronic components such as polysilicon, AlN and GaN. Extensive research effort has been directed to improve deposition quality and throughput. To obtain fast and high quality deposition, operational conditions such as temperature, pressure, fluid velocity and species concentration and geometry conditions such as source-substrate distance need to be well controlled in a CVD system. This thesis will focus on design of CVD processes through understanding the transport and reaction phenomena in the growth reactor. Since the in situ monitor is almost impossible for CVD reactor, many industrial resources have been expended to determine the optimum design by semi-empirical methods and trial-and-error procedures. This approach has allowed the achievement of improvements in the deposition sequence, but begins to show its limitations, as this method cannot always fulfill the more and more stringent specifications of the industry. To resolve this problem, numerical simulation is widely used in studying the growth techniques. The difficulty of numerical simulation of TACVD crystal growth process lies in the simulation of gas phase and surface reactions, especially the latter one, due to the fact that very limited kinetic information is available in the open literature. In this thesis, an advanced deposition model was developed to study the multi-component fluid flow, homogeneous gas phase reactions inside the reactor chamber, heterogeneous surface

  6. Biocompatible circuit-breaker chip for thermal management of biomedical microsystems

    NASA Astrophysics Data System (ADS)

    Luo, Yi; Dahmardeh, Masoud; Takahata, Kenichi

    2015-05-01

    This paper presents a thermoresponsive micro circuit breaker for biomedical applications specifically targeted at electronic intelligent implants. The circuit breaker is micromachined to have a shape-memory-alloy cantilever actuator as a normally closed temperature-sensitive switch to protect the device of interest from overheating, a critical safety feature for smart implants including those that are electrothermally driven with wireless micro heaters. The device is fabricated in a size of 1.5  ×  2.0  ×  0.46 mm3 using biocompatible materials and a chip-based titanium package, exhibiting a nominal cold-state resistance of 14 Ω. The breaker rapidly enters the full open condition when the chip temperature exceeds 63 °C, temporarily breaking the circuit of interest to lower its temperature until chip temperature drops to 51 °C, at which the breaker closes the circuit to allow current to flow through it again, physically limiting the maximum temperature of the circuit. This functionality is tested in combination with a wireless resonant heater powered by radio-frequency electromagnetic radiation, demonstrating self-regulation of heater temperature. The developed circuit-breaker chip operates in a fully passive manner that removes the need for active sensor and circuitry to achieve temperature regulation in a target device, contributing to the miniaturization of biomedical microsystems including electronic smart implants where thermal management is essential.

  7. Fighting Fire with Fire: Modeling the Datacenter-Scale Effects of Targeted Superlattice Thermal Management

    SciTech Connect

    Biswas, S; Tiwari, M; Theogarajan, L; Sherwood, T P; Chong, F T

    2010-11-11

    Local thermal hot-spots in microprocessors lead to worst case provisioning of global cooling resources, especially in large-scale systems. However, efficiency of cooling solutions degrade non-linearly with supply temperature, resulting in high power consumption and cost in cooling - 50 {approx} 100% of IT power. Recent advances in active cooling techniques have shown on-chip thermoelectric coolers (TECs) to be very efficient at selectively eliminating small hot-spots, where applying current to a superlattice film deposited between silicon and the heat spreader results in a Peltier effect that spreads the heat and lowers the temperature of the hot-spot significantly to improve chip reliability. In this paper, we propose that hot-spot mitigation using thermoelectric coolers can be used as a power management mechanism to allow global coolers to be provisioned for a better worst case temperature leading to substantial savings in cooling power. In order to quantify the potential power savings from using TECs in data center servers, we present a detailed power model that integrates on-chip dynamic and leakage power sources, heat diffusion through the entire chip, TEC and global cooler efficiencies, and all their mutual interactions. Our multiscale analysis shows that, for a typical data center, TECs allow global coolers to operate at higher temperatures without degrading chip lifetime, and thus save {approx}27% cooling power on average while providing the same processor reliability as a data center running at 288K.

  8. Thermal neutron activation system for confirmatory nonmetallic land mine detection

    NASA Astrophysics Data System (ADS)

    McFee, John E.; Cousins, Thomas; Jones, Trevor; Brisson, Jean R.; Jamieson, Terry; Waller, Ed; LeMay, Francois; Ing, Harry; Clifford, Edward T. H.; Selkirk, Barkley

    1998-09-01

    To detect and locate buried landmines, the Canadian Department of National Defence (DND) is developing a teleoperated, vehicle-mounted, multisensor system called ILDP. In operation, a suite of 4 detectors scan ahead of the vehicle. Their outputs are combined through data fusion to indicate the possibility of a mine at a particular location, within a 30 cm radius. A thermal neutron activation (TNA) sensor, mounted behind the vehicle, is used to confirm the presence of explosives via detection of the 10.83 MeV gamma-ray associated with neutron capture on 14N. The TNA system developed for this uses a 100 microgram 252Cf neutron source surrounded by four 7.62 cm X 7.62 cm NaI(Tl) detectors. A combination of the use of state-of-the art radiation transport codes for design, judicious choice of specialized shielding materials and development of high-rate, fast pulse processing electronics has led to a system which can; (1) confirm the presence of all surface-laid or shallowly-buried anti-tank mines in a few seconds to a minute (depending on mass of explosive) (2) confirm the presence of anti-tank mines down to 20 cm depth in less than 5 minutes. (3) confirm the presence of large (greater than 100 g Nitrogen) anti-personnel mines in less than five minutes (4) operate in adverse climatic conditions. These results have been verified in field trials using the prototype sensor. Work is now ongoing to miniaturize the electronics, make the system robust and easy to use and investigate the use of an electronic neutron generator expected to enter service by the year 2000.

  9. Methane storage in flexible metal-organic frameworks with intrinsic thermal management.

    PubMed

    Mason, Jarad A; Oktawiec, Julia; Taylor, Mercedes K; Hudson, Matthew R; Rodriguez, Julien; Bachman, Jonathan E; Gonzalez, Miguel I; Cervellino, Antonio; Guagliardi, Antonietta; Brown, Craig M; Llewellyn, Philip L; Masciocchi, Norberto; Long, Jeffrey R

    2015-11-19

    As a cleaner, cheaper, and more globally evenly distributed fuel, natural gas has considerable environmental, economic, and political advantages over petroleum as a source of energy for the transportation sector. Despite these benefits, its low volumetric energy density at ambient temperature and pressure presents substantial challenges, particularly for light-duty vehicles with little space available for on-board fuel storage. Adsorbed natural gas systems have the potential to store high densities of methane (CH4, the principal component of natural gas) within a porous material at ambient temperature and moderate pressures. Although activated carbons, zeolites, and metal-organic frameworks have been investigated extensively for CH4 storage, there are practical challenges involved in designing systems with high capacities and in managing the thermal fluctuations associated with adsorbing and desorbing gas from the adsorbent. Here, we use a reversible phase transition in a metal-organic framework to maximize the deliverable capacity of CH4 while also providing internal heat management during adsorption and desorption. In particular, the flexible compounds Fe(bdp) and Co(bdp) (bdp(2-) = 1,4-benzenedipyrazolate) are shown to undergo a structural phase transition in response to specific CH4 pressures, resulting in adsorption and desorption isotherms that feature a sharp 'step'. Such behaviour enables greater storage capacities than have been achieved for classical adsorbents, while also reducing the amount of heat released during adsorption and the impact of cooling during desorption. The pressure and energy associated with the phase transition can be tuned either chemically or by application of mechanical pressure. PMID:26503057

  10. Methane storage in flexible metal-organic frameworks with intrinsic thermal management

    NASA Astrophysics Data System (ADS)

    Mason, Jarad A.; Oktawiec, Julia; Taylor, Mercedes K.; Hudson, Matthew R.; Rodriguez, Julien; Bachman, Jonathan E.; Gonzalez, Miguel I.; Cervellino, Antonio; Guagliardi, Antonietta; Brown, Craig M.; Llewellyn, Philip L.; Masciocchi, Norberto; Long, Jeffrey R.

    2015-11-01

    As a cleaner, cheaper, and more globally evenly distributed fuel, natural gas has considerable environmental, economic, and political advantages over petroleum as a source of energy for the transportation sector. Despite these benefits, its low volumetric energy density at ambient temperature and pressure presents substantial challenges, particularly for light-duty vehicles with little space available for on-board fuel storage. Adsorbed natural gas systems have the potential to store high densities of methane (CH4, the principal component of natural gas) within a porous material at ambient temperature and moderate pressures. Although activated carbons, zeolites, and metal-organic frameworks have been investigated extensively for CH4 storage, there are practical challenges involved in designing systems with high capacities and in managing the thermal fluctuations associated with adsorbing and desorbing gas from the adsorbent. Here, we use a reversible phase transition in a metal-organic framework to maximize the deliverable capacity of CH4 while also providing internal heat management during adsorption and desorption. In particular, the flexible compounds Fe(bdp) and Co(bdp) (bdp2- = 1,4-benzenedipyrazolate) are shown to undergo a structural phase transition in response to specific CH4 pressures, resulting in adsorption and desorption isotherms that feature a sharp ‘step’. Such behaviour enables greater storage capacities than have been achieved for classical adsorbents, while also reducing the amount of heat released during adsorption and the impact of cooling during desorption. The pressure and energy associated with the phase transition can be tuned either chemically or by application of mechanical pressure.

  11. Graphene quilts for thermal management of high-power GaN transistors.

    PubMed

    Yan, Zhong; Liu, Guanxiong; Khan, Javed M; Balandin, Alexander A

    2012-01-01

    Self-heating is a severe problem for high-power gallium nitride (GaN) electronic and optoelectronic devices. Various thermal management solutions, for example, flip-chip bonding or composite substrates, have been attempted. However, temperature rise due to dissipated heat still limits applications of the nitride-based technology. Here we show that thermal management of GaN transistors can be substantially improved via introduction of alternative heat-escaping channels implemented with few-layer graphene-an excellent heat conductor. The graphene-graphite quilts were formed on top of AlGaN/GaN transistors on SiC substrates. Using micro-Raman spectroscopy for in situ monitoring we demonstrated that temperature of the hotspots can be lowered by ∼20 °C in transistors operating at ∼13 W mm(-1), which corresponds to an order-of-magnitude increase in the device lifetime. The simulations indicate that graphene quilts perform even better in GaN devices on sapphire substrates. The proposed local heat spreading with materials that preserve their thermal properties at nanometre scale represents a transformative change in thermal management. PMID:22569371

  12. Thermal Analysis of ISS Service Module Active TCS

    NASA Technical Reports Server (NTRS)

    Altov, Vladimir V.; Zaletaev, Sergey V.; Belyavskiy, Evgeniy P.

    2000-01-01

    ISS Service Module mission must begin in July 2000. The verification of design thermal requirements is mostly due to thermal analysis. The thermal analysis is enough difficult problem because of large number of ISS configurations that had to be investigated and various orbital environments. Besides the ISS structure has articulating parts such as solar arrays and radiators. The presence of articulating parts greatly increases computation times and requires accurate approach to organization of calculations. The varying geometry needs us to calculate the view factors several times during the orbit, while in static geometry case we need do it only once. In this paper we consider the thermal mathematical model of SM that includes the TCS and construction thermal models and discuss the results of calculations for ISS configurations 1R and 9Al. The analysis is based on solving the nodal heat balance equations for ISS structure by Kutta-Merson method and analytical solutions of heat transfer equations for TCS units. The computations were performed using thermal software TERM [1,2] that will be briefly described.

  13. Thermal management for a Mach 5 cruise aircraft using endothermic fuel

    NASA Technical Reports Server (NTRS)

    Petley, Dennis H.; Jones, Stuart C.

    1990-01-01

    The present thermal management system for a carrier-based Mach 5 cruise-capable aircraft whose propulsion system does not entail cryogenic fuels is predicated on the use of the catalytic endothermic reaction of a petroleum-derived hydrocarbon fuel as the heat sink for engine cooling. The insulation of engine flowpath surfaces reduces cooling requirements. The primary elements of this closed-cycle cooling system are a fuel preheater, a catalytic fuel reactor, and engine wall-cooling panels; a silicone-based liquid polymer is used as the coolant. Structural, weight, and thermal analysis results are presented for each of the primary components.

  14. Design and simulation of a lithium-ion battery with a phase change material thermal management system for an electric scooter

    NASA Astrophysics Data System (ADS)

    Khateeb, Siddique A.; Farid, Mohammed M.; Selman, J. Robert; Al-Hallaj, Said

    A lithium-ion battery employing a novel phase change material (PCM) thermal management system was designed for an electric scooter. Passive thermal management systems using PCM can control the temperature excursions and maintain temperature uniformity in Li-ion batteries without the use of active cooling components such as a fan, a blower or a pump found in air/liquid-cooling systems. Hence, the advantages of a compact, lightweight, and energy efficient system can be achieved with this novel form of thermal management system. Simulation results are shown for a Li-ion battery sub-module consisting of nine 18650 Li-ion cells surrounded by PCM with a melting point between 41 and 44 °C. The use of aluminum foam within the PCM and fins attached to the battery module were studied to overcome the low thermal conductivity of the PCM and the low natural convection heat transfer coefficient. The comparative results of the PCM performance in the presence of Al-foam and Al-fins are shown. The battery module is also simulated for summer and winter conditions. The effect of air-cooling on the Li-ion battery was also studied. These simulation results demonstrate the successful use of the PCM as a potential candidate for thermal management solution in electric scooter applications and therefore for other electric vehicle applications.

  15. A New Activity-Based Financial Cost Management Method

    NASA Astrophysics Data System (ADS)

    Qingge, Zhang

    The standard activity-based financial cost management model is a new model of financial cost management, which is on the basis of the standard cost system and the activity-based cost and integrates the advantages of the two. It is a new model of financial cost management with more accurate and more adequate cost information by taking the R&D expenses as the accounting starting point and after-sale service expenses as the terminal point and covering the whole producing and operating process and the whole activities chain and value chain aiming at serving the internal management and decision.

  16. Active management of food allergy: an emerging concept.

    PubMed

    Anagnostou, Katherine; Stiefel, Gary; Brough, Helen; du Toit, George; Lack, Gideon; Fox, Adam T

    2015-04-01

    IgE-mediated food allergies are common and currently there is no cure. Traditionally, management has relied upon patient education, food avoidance and the provision of an emergency medication plan. Despite this, food allergy can significantly impact on quality of life. Therefore, in recent years, evolving research has explored alternative management strategies. A more active approach to management is being adopted, which includes early introduction of potentially allergenic foods, anticipatory testing, active monitoring, desensitisation to food allergens and active risk management. This review will discuss these areas in turn. PMID:25378378

  17. The multi-thermal emission in solar active regions

    NASA Astrophysics Data System (ADS)

    Del Zanna, G.

    2013-10-01

    We present simultaneous SDO AIA and Hinode EIS observations of the hot cores of active regions (ARs) and assess the dominant contributions to the AIA EUV bands. This is an extension of our previous work. We find good agreement between SDO AIA, EVE and EIS observations, using our new EIS calibration and the latest EVE v.3 data. We find that all the AIA bands are multi-thermal, with the exception of the 171 and 335 Å, and provide ways to roughly estimate the main contributions directly from the AIA data. We present and discuss new atomic data for the AIA bands, showing that they are now sufficiently complete to obtain temperature information in the cores of ARs, with the exception of the 211 Å band. We found that the newly identified Fe xiv 93.61 Å line is the dominant contribution to the 94 Å band, whenever Fe xviii is not present. Three methods to estimate the Fe xviii emission in this band are presented, two using EIS and one directly from the AIA data. Fe xviii emission is often present in the cores of ARs, but we found cases where it is formed at 3 MK and not 7 MK, the temperature of peak ion abundance in equilibrium. The best EIS lines for elemental abundance determination and differential emission measure (DEM) analysis are discussed. A new set of abundances for many elements are obtained from EIS observations of hot 3 MK loops. The abundances of the elements with low first ionisation potential (FIP), relative to those of the high-FIP elements, are found to be enhanced by about a factor of three, compared to the photospheric values. A measurement of the path length implies that the absolute abundances of the low-FIP elements are higher than the photospheric values by at least a factor of three. We present a new DEM method customised for the AIA bands, to study the thermal structure of ARs at 1'' resolution. This was tested on a few ARs, including one observed during the Hi-C rocket flight. We found excellent agreement between predicted and observed AIA

  18. Boundary Creek Thermal areas of Yellowstone National Park I: thermal activity and geologic setting

    SciTech Connect

    Hutchinson, R.A.

    1980-09-01

    Proposed geothermal leasing in the Island Park Geothermal Area (IPGA) in national forest and public lands adjacent to Yellowstone National Park has called attention to the moderate to high temperature springs of the Boundary Creek Thermal Areas. Up until late 1977 no description or geochemical inventory studies had been conducted in these areas. The thermal springs are scattered in four major groups along the Boundary Creek drainage with three to six km. of the IPGA - park border. Observations and analyses of physical and chemical indicators suggest that the source is under the Madison Plateau and that the waters are generally similar in the lower three thermal units. These hot springs should be monitored so as to provide early warning of change in the event that geothermal development in the IPGA causes withdrawal of groundwater from Yellow Stone National Park.

  19. Thermal management system and method for a solid-state energy storing device

    DOEpatents

    Rouillard, Roger; Domroese, Michael K.; Gauthier, Michel; Hoffman, Joseph A.; Lindeman, David D.; Noel, Joseph-Robert-Gaetan; Radewald, Vern E.; Ranger, Michel; Rouillard, Jean; Shiota, Toshimi; St-Germain, Philippe; Sudano, Anthony; Trice, Jennifer L.; Turgeon, Thomas A.

    2000-01-01

    An improved electrochemical energy storing device includes a number of thin-film electrochemical cells which are maintained in a state of compression through use of an internal or an external pressure apparatus. A thermal conductor, which is connected to at least one of the positive or negative contacts of each electrochemical cell, conducts current into and out of the electrochemical cells and also conducts thermal energy between the electrochemical cells and thermally conductive material disposed on a wall structure adjacent the conductors. The wall structure includes electrically resistive material, such as an anodized coating or a thin film of plastic. The thermal conductors are fabricated to include a spring mechanism which expands and contacts to maintain mechanical contact between the electrochemical cells and the thermally conductive material in the presence of relative movement between the electrochemical cells and the wall structure. An active cooling apparatus may be employed external to a hermetically sealed housing containing the electrochemical cells to enhance the transfer of thermal energy into and out of the electrochemical cells. An integrated interconnect board may be disposed within the housing onto which a number of electrical and electro-mechanical components are mounted. Heat generated by the components is conducted from the interconnect board to the housing using the thermal conductors.

  20. US - Former Soviet Union environmental management activities

    SciTech Connect

    1995-09-01

    The Office of Environmental Management (EM) has been delegated the responsibility for US DOE`s cleanup of nuclear weapons complex. The nature and the magnitude of the waste management and environmental remediation problem requires the identification of technologies and scientific expertise from domestic and foreign sources. This booklet makes comparisons and describes coordinated projects and workshops between the USA and the former Soviet Union.

  1. Assessment of increased thermal activity at Mount Baker, Washington, March 1975-March 1976

    USGS Publications Warehouse

    Frank, David; Meier, Mark Frederick; Swanson, Donald A.; with contributions by Babcock, James W.; Fretwell, Marvin O.; Malone, Stephen D.; Rosenfeld, Charles L.; Shreve, Ronald L.; Wilcox, Ray E.

    1977-01-01

    for smaller avalanches and mudflows. An earthquake, steam explosion, or eruption could provide a suitable trigger to initiate movement. Although such triggering events were possible before 1975, the probability might have been as much as 10 times greater in 1975 because of the increased thermal activity. The threat of avalanches and mudflows on Boulder Creek valley and Baker Lake prompted the closure by management agencies of the Boulder Creek drainage and of Baker Lake and its shoreline in the summer of 1975. Additionally, Baker Lake was kept below full pool at a level calculated to prevent overtopping of Upper Baker Dam by waves which could result from a worst-case avalanche. In 1975 an interdisciplinary program of seismic, tilt, gravity, gas, hydrologic, petrologic, thermal infrared, and photographic studies by Federal and university scientists was initiated to evaluate the impact of the current thermal activity and to monitor changes that might indicate an impending eruption. By March 1976 only one small earth- quake had been identified beneath Mount Baker. Tilt and gravity changes have been observed but cannot be attributed solely to volcanic causes. The data available thus far provide no evidence of an impending eruption, but they cannot be fully interpreted without many additional geophysical and geochemical measurements, as it is not yet possible to clearly distinguish volcanic effects from non- volcanic background effects. Inasmuch as current activity continues unchanged - without steam explosions, eruptions, or frequent or large earthquakes - the probability of a suitable trigger for large avalanches and mudflows should decrease and should approach that of a more average year. Such an average year would have a hazard probability at least as great as that which existed before 1975, although that level of hazard was not recognized at the time by the public or by administrative agencies. The potential hazard and the uncertainties of future activ

  2. Thermal Management of Power Semiconductor Packages - Matching Cooling Technologies with Packaging Technologies (Presentation)

    SciTech Connect

    Bennion, K.; Moreno, G.

    2010-04-27

    Heat removal for power semiconductor devices is critical for robust operation. Because there are different packaging options, different thermal management technologies, and a range of applications, there is a need for a methodology to match cooling technologies and package configurations to target applications. To meet this need, a methodology was developed to compare the sensitivity of cooling technologies on the overall package thermal performance over a range of power semiconductor packaging configurations. The results provide insight into the trade-offs associated with cooling technologies and package configurations. The approach provides a method for comparing new developments in power semiconductor packages and identifying potential thermal control technologies for the package. The results can help users select the appropriate combination of packaging configuration and cooling technology for the desired application.

  3. A Thermal Management Systems Model for the NASA GTX RBCC Concept

    NASA Technical Reports Server (NTRS)

    Traci, Richard M.; Farr, John L., Jr.; Laganelli, Tony; Walker, James (Technical Monitor)

    2002-01-01

    The Vehicle Integrated Thermal Management Analysis Code (VITMAC) was further developed to aid the analysis, design, and optimization of propellant and thermal management concepts for advanced propulsion systems. The computational tool is based on engineering level principles and models. A graphical user interface (GUI) provides a simple and straightforward method to assess and evaluate multiple concepts before undertaking more rigorous analysis of candidate systems. The tool incorporates the Chemical Equilibrium and Applications (CEA) program and the RJPA code to permit heat transfer analysis of both rocket and air breathing propulsion systems. Key parts of the code have been validated with experimental data. The tool was specifically tailored to analyze rocket-based combined-cycle (RBCC) propulsion systems being considered for space transportation applications. This report describes the computational tool and its development and verification for NASA GTX RBCC propulsion system applications.

  4. Topology, Design, Analysis, and Thermal Management of Power Electronics for Hybrid Electric Vehicle Applications

    SciTech Connect

    Mi, C.; Peng, F. Z.; Kelly, K. J.; O'Keefe, M.; Hassani, V.

    2008-01-01

    Power electronics circuits play an important role in the success of electric, hybrid and fuel cell vehicles. Typical power electronics circuits in hybrid vehicles include electric motor drive circuits and DC/DC converter circuits. Conventional circuit topologies, such as buck converters, voltage source inverters and bidirectional boost converters are challenged by system cost, efficiency, controllability, thermal management, voltage and current capability, and packaging issues. Novel topologies, such as isolated bidirectional DC/DC converters, multilevel converters, and Z-source inverters, offer potential improvement to hybrid vehicle system performance, extended controllability and power capabilities. This paper gives an overview of the topologies, design, and thermal management, and control of power electronics circuits in hybrid vehicle applications.

  5. Active cooling-based surface confinement system for thermal soil treatment

    DOEpatents

    Aines, Roger D.; Newmark, Robin L.

    1997-01-01

    A thermal barrier is disclosed for surface confinement with active cooling to control subsurface pressures during thermal remediation of shallow (5-20 feet) underground contaminants. If steam injection is used for underground heating, the actively cooled thermal barrier allows the steam to be injected into soil at pressures much higher (20-60 psi) than the confining strength of the soil, while preventing steam breakthrough. The rising steam is condensed to liquid water at the thermal barrier-ground surface interface. The rapid temperature drop forced by the thermal barrier drops the subsurface pressure to below atmospheric pressure. The steam and contaminant vapors are contained by the thermal blanket, which can be made of a variety of materials such as steel plates, concrete slabs, membranes, fabric bags, or rubber bladders.

  6. Efficient thermal image segmentation through integration of nonlinear enhancement with unsupervised active contour model

    NASA Astrophysics Data System (ADS)

    Albalooshi, Fatema A.; Krieger, Evan; Sidike, Paheding; Asari, Vijayan K.

    2015-03-01

    Thermal images are exploited in many areas of pattern recognition applications. Infrared thermal image segmentation can be used for object detection by extracting regions of abnormal temperatures. However, the lack of texture and color information, low signal-to-noise ratio, and blurring effect of thermal images make segmenting infrared heat patterns a challenging task. Furthermore, many segmentation methods that are used in visible imagery may not be suitable for segmenting thermal imagery mainly due to their dissimilar intensity distributions. Thus, a new method is proposed to improve the performance of image segmentation in thermal imagery. The proposed scheme efficiently utilizes nonlinear intensity enhancement technique and Unsupervised Active Contour Models (UACM). The nonlinear intensity enhancement improves visual quality by combining dynamic range compression and contrast enhancement, while the UACM incorporates active contour evolutional function and neural networks. The algorithm is tested on segmenting different objects in thermal images and it is observed that the nonlinear enhancement has significantly improved the segmentation performance.

  7. Active cooling-based surface confinement system for thermal soil treatment

    DOEpatents

    Aines, R.D.; Newmark, R.L.

    1997-10-28

    A thermal barrier is disclosed for surface confinement with active cooling to control subsurface pressures during thermal remediation of shallow (5-20 feet) underground contaminants. If steam injection is used for underground heating, the actively cooled thermal barrier allows the steam to be injected into soil at pressures much higher (20-60 psi) than the confining strength of the soil, while preventing steam breakthrough. The rising steam is condensed to liquid water at the thermal barrier-ground surface interface. The rapid temperature drop forced by the thermal barrier drops the subsurface pressure to below atmospheric pressure. The steam and contaminant vapors are contained by the thermal blanket, which can be made of a variety of materials such as steel plates, concrete slabs, membranes, fabric bags, or rubber bladders. 1 fig.

  8. Understanding support mediated activity by investigating highly active, thermally stable, silica supported gold catalysts

    SciTech Connect

    Veith, Gabriel M; Lupini, Andrew R; Rashkeev, Sergey; Pennycook, Stephen J; Schwartz, Viviane; Mullins, David R; Dudney, Nancy J

    2009-01-01

    2.5 nm gold nanoparticles were grown on a fumed silica support using the physical vapor deposition technique magnetron sputtering. Combining electron microscopy, extended X-ray absorption fine structure (EXAFS) spectroscopy, and catalytic studies revealed that the silica supported gold catalysts are thermally stable when annealed in an oxygen containing environment up to at least 500oC. This surprising stability is attributed to the absence of residual halide impurities and a strong bond between gold and defects at the silica surface (2.7 - 3.8 eV), as estimated from density functional theory (DFT) calculations. The Au/SiO2 catalysts are slightly less active for CO oxidation than the prototypical Au/TiO2 catalysts, however they can be regenerated far more easily, fully recovering the activity of a freshly prepared catalyst after deactivation.

  9. Electrochemical-Thermal Modeling and Microscale Phase Change for Passive Internal Thermal Management of Lithium Ion Batteries

    NASA Astrophysics Data System (ADS)

    Bandhauer, Todd Matthew

    In the current investigation, a fully coupled electrochemical and thermal model for lithium-ion batteries is developed to investigate the effects of different thermal management strategies on battery performance. This work represents the first ever study of these coupled electrochemical-thermal phenomena in batteries from the electrochemical heat generation all the way to the dynamic heat removal in actual hybrid electric vehicles (HEV) drive cycles. In addition, a novel, passive internal cooling system that uses heat removal through liquid-vapor phase change is developed. The proposed cooling system passively removes heat almost isothermally with negligible thermal resistances between the heat source and cooling fluid, thereby allowing battery performance to improve unimpeded by thermal limitations. For the battery model, local electrochemical reaction rates are predicted using temperature-dependent data on a commercially available battery designed for high rates (C/LiFePO4) in a computationally efficient manner. Data were collected on this small battery (˜1 Ah) over a wide range of temperatures (10°C to 60°C), depths of discharge (0.15 Ah < DOD < 0.95 Ah), and rates (-5 A to 5 A) using two separate test facilities to maintain sufficient temperature fidelity and to discern the relative influence of reversible and irreversible heating. The results show that total volumetric heat generation is a primarily a function of current and DOD, and secondarily a function of temperature. The results also show that reversible heating is significant compared to irreversible heating, with a minimum of 7.5% of the total heat generation attributable to reversible heating at 5 A and 15°C. Additional tests show that these constant current data can be used to simulate the response of the battery to dynamic loading, which serves as the basis for the electrochemical-thermal model development. This model is then used to compare the effects of external and internal cooling on battery

  10. Air Force space power and thermal management technology - Requirements for the early 21st century

    NASA Astrophysics Data System (ADS)

    Herrera, Ernest D.; Kuck, Inara

    Typical projections for military space power and thermal management technologies have posited requirements for high powered and highly survivable systems. Recent changes in defense needs, however, will require spacecraft that are smaller, lower powered, less survivable, and highly proliferated. Technologies will be developed to provide low cost, ultra-light, high power density, 'smart' conventional power systems. Compact nuclear power systems will also be developed to meet higher power needs.

  11. Quarterly Briefing Book on Environmental and Waste Management Activities

    SciTech Connect

    Brown, M.C.

    1991-06-01

    The purpose of the Quarterly Briefing Book on Environmental and Waste Management Activities is to provide managers and senior staff at the US Department of Energy-Richland Operations Office and its contractors with timely and concise information on Hanford Site environmental and waste management activities. Each edition updates the information on the topics in the previous edition, deletes those determined not to be of current interest, and adds new topics to keep up to date with changing environmental and waste management requirements and issues. Section A covers current waste management and environmental restoration issues. In Section B are writeups on national or site-wide environmental and waste management topics. Section C has writeups on program- and waste-specific environmental and waste management topics. Section D provides information on waste sites and inventories on the site. 15 figs., 4 tabs.

  12. All-Solid-State Electrochromic Variable Emittance Coatings for Thermal Management in Space

    NASA Astrophysics Data System (ADS)

    Kislov, Nikolai; Groger, Howard; Ponnappan, Rengasamy

    2003-01-01

    The results presented in this article demonstrate the feasibility of ``all-solid-state'' inorganic electrochromic (EC) variable emittance coatings (VEC) for thermal management in space. VECs were built on glass substrates, flexible polyimide (Kapton™) films, and on high resistance silicon wafers. The best VECs were found to modulate mid-infrared emittance from 0.15 to 0.46 on a Kapton film and from 0.24 to 0.48 on a silicon wafer that performs the dual role as both infrared window and substrate. The results of thermal estimations for a two-dimensional plate showed that EC systems with emittance modulation ratio ɛhigh/Vegr low = 3 can be practically used to advantage in providing enhanced thermal control for lightweight structures in space. In addition, EC variable solar reflectance coatings (VSRCs) were built on polyethylene terephthalate (PET) film. The average reflection of the VSRC in a visual spectral range was 63% in the bleached condition and 20% in the colored condition. Thermal analysis shows that a combination of VECs and VSRCs described in this work provides an enhanced range of thermal control for satellites and small space vehicles in the space environment.

  13. Thermal management in MoS2 based integrated device using near-field radiation

    NASA Astrophysics Data System (ADS)

    Peng, Jiebin; Zhang, Gang; Li, Baowen

    2015-09-01

    Recently, wafer-scale growth of monolayer MoS2 films with spatial homogeneity is realized on SiO2 substrate. Together with the latest reported high mobility, MoS2 based integrated electronic devices are expected to be fabricated in the near future. Owing to the low lattice thermal conductivity in monolayer MoS2, and the increased transistor density accompanied with the increased power density, heat dissipation will become a crucial issue for these integrated devices. In this letter, using the formalism of fluctuation electrodynamics, we explored the near-field radiative heat transfer from a monolayer MoS2 to graphene. We demonstrate that in resonance, the maximum heat transfer via near-field radiation between MoS2 and graphene can be ten times higher than the in-plane lattice thermal conduction for MoS2 sheet. Therefore, an efficient thermal management strategy for MoS2 integrated device is proposed: Graphene sheet is brought into close proximity, 10-20 nm from MoS2 device; heat energy transfer from MoS2 to graphene via near-field radiation; this amount of heat energy then be conducted to contact due to ultra-high lattice thermal conductivity of graphene. Our work sheds light for developing cooling strategy for nano devices constructing with low thermal conductivity materials.

  14. Thermal management in MoS{sub 2} based integrated device using near-field radiation

    SciTech Connect

    Peng, Jiebin; Zhang, Gang; Li, Baowen

    2015-09-28

    Recently, wafer-scale growth of monolayer MoS{sub 2} films with spatial homogeneity is realized on SiO{sub 2} substrate. Together with the latest reported high mobility, MoS{sub 2} based integrated electronic devices are expected to be fabricated in the near future. Owing to the low lattice thermal conductivity in monolayer MoS{sub 2}, and the increased transistor density accompanied with the increased power density, heat dissipation will become a crucial issue for these integrated devices. In this letter, using the formalism of fluctuation electrodynamics, we explored the near-field radiative heat transfer from a monolayer MoS{sub 2} to graphene. We demonstrate that in resonance, the maximum heat transfer via near-field radiation between MoS{sub 2} and graphene can be ten times higher than the in-plane lattice thermal conduction for MoS{sub 2} sheet. Therefore, an efficient thermal management strategy for MoS{sub 2} integrated device is proposed: Graphene sheet is brought into close proximity, 10–20 nm from MoS{sub 2} device; heat energy transfer from MoS{sub 2} to graphene via near-field radiation; this amount of heat energy then be conducted to contact due to ultra-high lattice thermal conductivity of graphene. Our work sheds light for developing cooling strategy for nano devices constructing with low thermal conductivity materials.

  15. International Project Management Committee: Overview and Activities

    NASA Technical Reports Server (NTRS)

    Hoffman, Edward

    2010-01-01

    This slide presentation discusses the purpose and composition of the International Project Management Committee (IMPC). The IMPC was established by members of 15 space agencies, companies and professional organizations. The goal of the committee is to establish a means to share experiences and best practices with space project/program management practitioners at the global level. The space agencies that are involved are: AEB, DLR, ESA, ISRO, JAXA, KARI, and NASA. The industrial and professional organizational members are Comau, COSPAR, PMI, and Thales Alenia Space.

  16. Effect of thermal activation energy on dislocation emission from an elliptically blunted crack tip

    NASA Astrophysics Data System (ADS)

    Zeng, Xin; Fang, Qi-Hong; Liu, You-Wen

    2014-08-01

    Thermal activation processes are of fundamental importance for the understanding and modeling the strength of structural materials. In this paper, the effect of thermal activation energy on dislocation emission from an elliptically blunted crack tip is researched. Critical stress intensity factors are calculated for an edge dislocation emission from an elliptically blunted crack under mode I and mode II loading conditions at high temperature. The results show that the impact of thermal activation processes is remarkable, the value of the critical stress intensity factor for dislocation emission decreases at high temperature, which means the applied loads for dislocation emission will decrease with increment of temperature.

  17. Impact of active material surface area on thermal stability of LiCoO2 cathode

    NASA Astrophysics Data System (ADS)

    Geder, Jan; Hoster, Harry E.; Jossen, Andreas; Garche, Jürgen; Yu, Denis Y. W.

    2014-07-01

    Thermal stability of charged LiCoO2 cathodes with various surface areas of active material is investigated in order to quantify the effect of LiCoO2 surface area on thermal stability of cathode. Thermogravimetric analyses and calorimetry have been conducted on charged cathodes with different active material surface areas. Besides reduced thermal stability, high surface area also changes the active material decomposition reaction and induces side reactions with additives. Thermal analyses of LiCoO2 delithiated chemically without any additives or with a single additive have been conducted to elaborate the effect of particle size on side reactions. Stability of cathode-electrolyte system has been investigated by accelerating rate calorimetry (ARC). Arrhenius activation energy of cathode decomposition has been calculated as function of conversion at different surface area of active material.

  18. Description of data base management systems activities

    NASA Technical Reports Server (NTRS)

    1983-01-01

    One of the major responsibilities of the JPL Computing and Information Services Office is to develop and maintain a JPL plan for providing computing services to the JPL management and administrative community that will lead to improved productivity. The CISO plan to accomplish this objective has been titled 'Management and Administrative Support Systems' (MASS). The MASS plan is based on the continued use of JPL's IBM 3032 Computer system for administrative computing and for the MASS functions. The current candidate administrative Data Base Management Systems required to support the MASS include ADABASE, Cullinane IDMS and TOTAL. Previous uses of administrative Data Base Systems have been applied to specific local functions rather than in a centralized manner with elements common to the many user groups. Limited capacity data base systems have been installed in microprocessor based office automation systems in a few Project and Management Offices using Ashton-Tate dBASE II. These experiences plus some other localized in house DBMS uses have provided an excellent background for developing user and system requirements for a single DBMS to support the MASS program.

  19. Active control of primary mirror of an orbiting telescope with thermal excitation

    NASA Technical Reports Server (NTRS)

    Hill, J. L.; Youngblood, J. N.

    1973-01-01

    The results of a study of the feasibility of an active method of surface error control using thermal elements are presented. It is shown that the control effort of the thermal elements is sufficient for the purpose, and that such benefits as low cost, low weight, and high reliability may be achieved in conjunction with a significant reduction in the mirror surface error figure.

  20. Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

    NASA Technical Reports Server (NTRS)

    Emrich, William J. Jr.; Moran, Robert P.; Pearson, J. Boise

    2012-01-01

    To support the on-going nuclear thermal propulsion effort, a state-of-the-art non nuclear experimental test setup has been constructed to evaluate the performance characteristics of candidate fuel element materials and geometries in representative environments. The facility to perform this testing is referred to as the Nuclear Thermal Rocket Element Environment Simulator (NTREES). This device can simulate the environmental conditions (minus the radiation) to which nuclear rocket fuel components will be subjected during reactor operation. Test articles mounted in the simulator are inductively heated in such a manner so as to accurately reproduce the temperatures and heat fluxes which would normally occur as a result of nuclear fission and would be exposed to flowing hydrogen. Initial testing of a somewhat prototypical fuel element has been successfully performed in NTREES and the facility has now been shutdown to allow for an extensive reconfiguration of the facility which will result in a significant upgrade in its capabilities

  1. Application of thermal analysis techniques in activated carbon production

    USGS Publications Warehouse

    Donnals, G.L.; DeBarr, J.A.; Rostam-Abadi, M.; Lizzio, A.A.; Brady, T.A.

    1996-01-01

    Thermal analysis techniques have been used at the ISGS as an aid in the development and characterization of carbon adsorbents. Promising adsorbents from fly ash, tires, and Illinois coals have been produced for various applications. Process conditions determined in the preparation of gram quantities of carbons were used as guides in the preparation of larger samples. TG techniques developed to characterize the carbon adsorbents included the measurement of the kinetics of SO2 adsorption, the performance of rapid proximate analyses, and the determination of equilibrium methane adsorption capacities. Thermal regeneration of carbons was assessed by TG to predict the life cycle of carbon adsorbents in different applications. TPD was used to determine the nature of surface functional groups and their effect on a carbon's adsorption properties.

  2. Thermally-Activated Metal-to-Glass Bonding

    NASA Technical Reports Server (NTRS)

    Gallagher, B. D.

    1986-01-01

    Hermetic seals formed easily by use of metallo-organic film. Metallo-organic film thermally bonded to glass and soldered or welded to form hermetic seal. Film applied as ink consisting of silver neodecanoate in xylene. Relative amounts of ingredients selected to obtain desired viscosity. Material applied by printing or even by scribing with pen. Sealing technique useful in making solar-cell modules, microelectronic packages, and other hermetic silicon devices.

  3. Flightweight radiantly and actively cooled panel: Thermal and structural performance

    NASA Technical Reports Server (NTRS)

    Shore, C. P.; Nowak, R. J.; Kelly, H. N.

    1982-01-01

    A 2- by 4-ft flightweight panel was subjected to thermal/structural tests representative of design flight conditions for a Mach 6.7 transport and to off-design conditions simulating flight maneuvers and cooling system failures. The panel utilized Rene 41 heat shields backed by a thin layer of insulation to radiate away most of the 12 Btu/ft2-sec incident heating. A solution of ethylene glycol in water circulating through tubes in an aluminum-honeycomb-sandwich panel absorbed the remainder of the incident heating (0.8 Btu/sq ft-sec). The panel successfully withstood (1) 46.7 hr of radiant heating which included 53 thermal cycles and 5000 cycles of uniaxial inplane loading of + or - 1200 lfb/in; (2) simulated 2g-maneuver heating conditions and simulated cooling system failures without excessive temperatures on the structural panel; and (3) the extensive thermal/structural tests and the aerothermal tests reported in NASA TP-1595 without significant damage to the structural panel, coolant leaks, or hot-gas ingress to the structural panel.

  4. Heat transfer and thermal management of electric vehicle batteries with phase change materials

    NASA Astrophysics Data System (ADS)

    Ramandi, M. Y.; Dincer, I.; Naterer, G. F.

    2011-07-01

    This paper examines a passive thermal management system for electric vehicle batteries, consisting of encapsulated phase change material (PCM) which melts during a process to absorb the heat generated by a battery. A new configuration for the thermal management system, using double series PCM shells, is analyzed with finite volume simulations. A combination of computational fluid dynamics (CFD) and second law analysis is used to evaluate and compare the new system against the single PCM shells. Using a finite volume method, heat transfer in the battery pack is examined and the results are used to analyse the exergy losses. The simulations provide design guidelines for the thermal management system to minimize the size and cost of the system. The thermal conductivity and melting temperature are studied as two important parameters in the configuration of the shells. Heat transfer from the surroundings to the PCM shell in a non-insulated case is found to be infeasible. For a single PCM system, the exergy efficiency is below 50%. For the second case for other combinations, the exergy efficiencies ranged from 30-40%. The second shell content did not have significant influence on the exergy efficiencies. The double PCM shell system showed higher exergy efficiencies than the single PCM shell system (except a case for type PCM-1). With respect to the reference environment, it is found that in all cases the exergy efficiencies decreased, when the dead-state temperatures rises, and the destroyed exergy content increases gradually. For the double shell systems for all dead-state temperatures, the efficiencies were very similar. Except for a dead-state temperature of 302 K, with the other temperatures, the exergy efficiencies for different combinations are well over 50%. The range of exergy efficiencies vary widely between 15 and 85% for a single shell system, and between 30-80% for double shell systems.

  5. Enhanced active aluminum content and thermal behaviour of nano-aluminum particles passivated during synthesis using thermal plasma route

    NASA Astrophysics Data System (ADS)

    Mathe, Vikas L.; Varma, Vijay; Raut, Suyog; Nandi, Amiya Kumar; Pant, Arti; Prasanth, Hima; Pandey, R. K.; Bhoraskar, Sudha V.; Das, Asoka K.

    2016-04-01

    Here, we report synthesis and in situ passivation of aluminum nanoparticles using thermal plasma reactor. Both air and palmitc acid passivation was carried out during the synthesis in the thermal plasma reactor. The passivated nanoparticles have been characterized for their structural and morphological properties using X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. In order to understand nature of passivation vibrational spectroscopic analysis have been carried out. The enhancement in active aluminum content and shelf life for a palmitic acid passivated nano-aluminum particles in comparison to the air passivated samples and commercially available nano Al powder (ALEX) has been observed. Thermo-gravimetric analysis was used to estimate active aluminum content of all the samples under investigation. In addition cerimetric back titration method was also used to estimate AAC and the shelf life of passivated aluminum particles. Structural, microstructural and thermogravomateric analysis of four year aged passivated sample also depicts effectiveness of palmitic acid passivation.

  6. Firefighter feedback during active cooling: a useful tool for heat stress management?

    PubMed

    Savage, Robbie J; Lord, Cara; Larsen, Brianna L; Knight, Teagan L; Langridge, Peter D; Aisbett, Brad

    2014-12-01

    Monitoring an individual's thermic state in the workplace requires reliable feedback of their core temperature. However, core temperature measurement technology is expensive, invasive and often impractical in operational environments, warranting investigation of surrogate measures which could be used to predict core temperature. This study examines an alternative measure of an individual's thermic state, thermal sensation, which presents a more manageable and practical solution for Australian firefighters operating on the fireground. Across three environmental conditions (cold, warm, hot & humid), 49 Australian volunteer firefighters performed a 20-min fire suppression activity, immediately followed by 20 min of active cooling using hand and forearm immersion techniques. Core temperature (Tc) and thermal sensation (TS) were measured across the rehabilitation period at five minute intervals. Despite the decline in Tc and TS throughout the rehabilitation period, there was little similarity in the magnitude or rate of decline between each measure in any of the ambient conditions. Moderate to strong correlations existed between Tc and TS in the cool (0.41, p<0.05) and hot & humid (0.57, p<0.05) conditions, however this was resultant in strong correlation during the earlier stages of rehabilitation (first five minutes), which were not evident in the latter stages. Linear regression revealed TS to be a poor predictor of Tc in all conditions (SEE=0.45-0.54°C) with a strong trend for TS to over-predict Tc (77-80% of the time). There is minimal evidence to suggest that ratings of thermal sensation, which represent a psychophysical assessment of an individual's thermal comfort, are an accurate reflection of the response of an individual's core temperature. Ratings of thermal sensation can be highly variable amongst individuals, likely moderated by local skin temperature. In account of these findings, fire managers require a more reliable source of information to guide

  7. Multiple objective optimization for active sensor management

    NASA Astrophysics Data System (ADS)

    Page, Scott F.; Dolia, Alexander N.; Harris, Chris J.; White, Neil M.

    2005-03-01

    The performance of a multi-sensor data fusion system is inherently constrained by the configuration of the given sensor suite. Intelligent or adaptive control of sensor resources has been shown to offer improved fusion performance in many applications. Common approaches to sensor management select sensor observation tasks that are optimal in terms of a measure of information. However, optimising for information alone is inherently sub-optimal as it does not take account of any other system requirements such as stealth or sensor power conservation. We discuss the issues relating to developing a suite of performance metrics for optimising multi-sensor systems and propose some candidate metrics. In addition it may not always be necessary to maximize information gain, in some cases small increases in information gain may take place at the cost of large sensor resource requirements. Additionally, the problems of sensor tasking and placement are usually treated separately, leading to a lack of coherency between sensor management frameworks. We propose a novel approach based on a high level decentralized information-theoretic sensor management architecture that unifies the processes of sensor tasking and sensor placement into a single framework. Sensors are controlled using a minimax multiple objective optimisation approach in order to address probability of target detection, sensor power consumption, and sensor survivability whilst maintaining a target estimation covariance threshold. We demonstrate the potential of the approach through simulation of a multi-sensor, target tracking scenario and compare the results with a single objective information based approach.

  8. Interpreting Low Spatial Resolution Thermal Data from Active Volcanoes on Io and the Earth

    NASA Technical Reports Server (NTRS)

    Keszthelyi, L.; Harris, A. J. L.; Flynn, L.; Davies, A. G.; McEwen, A.

    2001-01-01

    The style of volcanism was successfully determined at a number of active volcanoes on Io and the Earth using the same techniques to interpret thermal remote sensing data. Additional information is contained in the original extended abstract.

  9. The thermal tolerance of crayfish could be estimated from respiratory electron transport system activity.

    PubMed

    Simčič, Tatjana; Pajk, Franja; Jaklič, Martina; Brancelj, Anton; Vrezec, Al

    2014-04-01

    Whether electron transport system (ETS) activity could be used as an estimator of crayfish thermal tolerance has been investigated experimentally. Food consumption rate, respiration rates in the air and water, the difference between energy consumption and respiration costs at a given temperature ('potential growth scope', PGS), and ETS activity of Orconectes limosus and Pacifastacus leniusculus were determined over a temperature range of 5-30°C. All concerned parameters were found to be temperature dependent. The significant correlation between ETS activity and PGS indicates that they respond similarly to temperature change. The regression analysis of ETS activity as an estimator of thermal tolerance at the mitochondrial level and PGS as an indicator of thermal tolerance at the organismic level showed the shift of optimum temperature ranges of ETS activity to the right for 2° in O. limosus and for 3° in P. leniusculus. Thus, lower estimated temperature optima and temperatures of optimum ranges of PGS compared to ETS activity could indicate higher thermal sensitivity at the organismic level than at a lower level of complexity (i.e. at the mitochondrial level). The response of ETS activity to temperature change, especially at lower and higher temperatures, indicates differences in the characteristics of the ETSs in O. limosus and P. leniusculus. O. limosus is less sensitive to high temperature. The significant correlation between PGS and ETS activity supports our assumption that ETS activity could be used for the rapid estimation of thermal tolerance in crayfish species. PMID:24679968

  10. Recent National Solar Thermal Test Facility activities, in partnership with industry

    NASA Astrophysics Data System (ADS)

    Ghanbari, Cherly; Cameron, Christopher P.; Ralph, Mark E.; Pacheco, James E.; Rawlinson, K. Scott; Evans, Lindsey R.

    The National Solar Thermal Test Facility (NSTTF) at Sandia National Laboratories in Albuquerque, New Mexico, USA conducts testing of solar thermal components and systems, funded primarily by the US Department of Energy. Activities are conducted in support of Central Receiver Technology, Distributed Receiver Technology and Design Assistance projects. All activities are performed in support of various cost-shared government/industry joint ventures and, on a design assistance basis, in support of a number of other industry partners.

  11. Thermal Technology Development Activities at the Goddard Space Flight Center - 2001

    NASA Technical Reports Server (NTRS)

    Butler, Dan

    2002-01-01

    This presentation provides an overview of thermal technology development activities carried out at NASA's Goddard Space Flight Center during 2001. Specific topics covered include: two-phase systems (heat pipes, capillary pumped loops, vapor compression systems and phase change materials), variable emittance systems, advanced coatings, high conductivity materials and electrohydrodynamic (EHD) thermal coatings. The application of these activities to specific space missions is also discussed.

  12. Recent National Solar Thermal Test Facility activities, in partnership with industry

    SciTech Connect

    Ghanbari, C.; Cameron, C.P.; Ralph, M.E.; Pacheco, J.E.; Rawlinson, K.S.; Evans, L.R.

    1994-10-01

    The National Solar Thermal Test Facility (NSTTF) at Sandia National Laboratories in Albuquerque, New Mexico, USA conducts testing of solar thermal components and systems, funded primarily by the US Department of Energy. Activities are conducted in support of Central Receiver Technology, Distributed Receiver Technology and Design Assistance projects. All activities are performed in support of various cost-shared government/industry joint ventures and, on a design assistance basis, in support of a number of other industry partners.

  13. Highly Efficient, Simplified, Solution-Processed Thermally Activated Delayed-Fluorescence Organic Light-Emitting Diodes.

    PubMed

    Kim, Young-Hoon; Wolf, Christoph; Cho, Himchan; Jeong, Su-Hun; Lee, Tae-Woo

    2016-01-27

    Highly efficient, simplified, solution-processed thermally activated delayed-fluorescence organic light-emitting diodes can be realized by using pure-organic thermally activated delayed fluorescence emitters and a multifunctional buffer hole-injection layer, in which high EQE (≈24%) and current efficiency (≈73 cd A(-1) ) are demonstrated. High-efficiency fluorescence red-emitting and blue-emitting devices can also be fabricated in this manner. PMID:26619309

  14. US EPA’s Watershed Management Research Activities

    EPA Science Inventory

    The U.S. Environmental Protection Agency’s Urban Watershed Management Branch (UWMB) is responsible for developing and demonstrating methods to manage the risk to public health, property and the environment from wet-weather flows (WWF) in urban watersheds. The activities are prim...

  15. Guide to good practices for line and training manager activities

    SciTech Connect

    1998-06-01

    The purpose of this guide is to provide direction for line and training managers in carrying out their responsibilities for training and qualifying personnel and to verify that existing training activities are effective.

  16. NASA's New Thermal Management Systems Roadmap; Whats in it, What it Means

    NASA Technical Reports Server (NTRS)

    Swanson, Ted

    2016-01-01

    In July of 2015 NASA publically released a new set of Technology Area Roadmaps that will be used to help guide future NASA-funded technology development efforts. One of these was the Thermal Management Systems Roadmap, often identified as TA14. This Roadmap identifies the time sequencing and interdependencies of high priority, advanced thermal control technology for the next 5 to 20 years. Available funding limits the development of new technology. The Roadmaps are the first step in the process of prioritizing HQ-supported technology funding. The 2015 Roadmaps are focused on planned mission architectures and needs, as identified in the NRC-led science Decadals and HEOMD's Design Reference Missions. Additionally, the 2015 Roadmaps focus on "applied " R&D as opposed to more basic research. The NASA Mission Directorates were all closely involved in development of 2015 Roadmaps, and an extensive external review was also conducted. This talk will discuss the Technology Roadmaps in general, and then focus on the specific technologies identified for TA 14, Thermal Management Systems.

  17. Multifunctional Nanofluids with 2D Nanosheets for thermal management and tribological applications

    NASA Astrophysics Data System (ADS)

    Taha Tijerina, Jose Jaime

    Conventional heat-transfer fluids such as water, ethylene glycol, standard oils and other lubricants are typically low-efficiency heat-transfer fluids. Thermal management plays a critical factor in many applications where these fluids can be used, such as in motors/engines, solar cells, biopharmaceuticals, fuel cells, high voltage power transmission systems, micro/nanoelectronics mechanical systems (MEMS/NEMS), and nuclear cooling among others. These insulating fluids require superb filler dispersion, high thermal conduction, and for certain applications as in electrical/electronic devices also electrical insulation. The miniaturization and high efficiency of electrical/electronic devices in these fields demand successful heat management and energy-efficient fluid-based heat-transfer systems. Recent advances in layered materials enable large scale synthesis of various two-dimensional (2D) structures. Some of these 2D materials are good choices as nanofillers in heat transfer fluids; mainly due to their inherent high thermal conductivity (TC) and high surface area available for thermal energy transport. Among various 2D-nanostructures, hexagonal boron nitride (h-BN) and graphene (G) exhibit versatile properties such as outstanding TC, excellent mechanical stability, and remarkable chemical inertness. The following research, even though investigate various conventional fluids, will focus on dielectric insulating nanofluids (mineral oil -- MO) with significant thermal performance. It is presented the plan for synthesis and characterization of stable high-thermal conductivity nanofluids using 2D-nanostructures of h-BN, which will be further incorporated at diverse filler concentrations to conventional fluids for cooling applications, without compromising its electrical insulating property. For comparison, properties of h-BN based fluids are compared with conductive fillers such as graphene; where graphene has similar crystal structure of h-BN and also has similar bulk

  18. Nonexercise activity thermogenesis in obesity management.

    PubMed

    Villablanca, Pedro A; Alegria, Jorge R; Mookadam, Farouk; Holmes, David R; Wright, R Scott; Levine, James A

    2015-04-01

    Obesity is linked to cardiovascular disease. The global increase in sedentary lifestyle is an important factor contributing to the rising prevalence of the obesity epidemic. Traditionally, counseling has focused on moderate- to vigorous-intensity exercise, with disappointing results. Nonexercise activity thermogenesis (NEAT) is an important component of daily energy expenditure. It represents the common daily activities, such as fidgeting, walking, and standing. These high-effect NEAT movements could result in up to an extra 2000 kcal of expenditure per day beyond the basal metabolic rate, depending on body weight and level of activity. Implementing NEAT during leisure-time and occupational activities could be essential to maintaining a negative energy balance. NEAT can be applied by being upright, ambulating, and redesigning workplace and leisure-time environments to promote NEAT. The benefits of NEAT include not only the extra calories expended but also the reduced occurrence of the metabolic syndrome, cardiovascular events, and all-cause mortality. We believe that to overcome the obesity epidemic and its adverse cardiovascular consequences, NEAT should be part of the current medical recommendations. The content of this review is based on a literature search of PubMed and the Google search engine between January 1, 1960, and October 1, 2014, using the search terms physical activity, obesity, energy expenditure, nonexercise activity thermogenesis, and NEAT. PMID:25841254

  19. Biomedical Applications of Thermally Activated Shape Memory Polymers

    SciTech Connect

    Small IV, W; Singhal, P; Wilson, T S; Maitland, D J

    2009-04-10

    Shape memory polymers (SMPs) are smart materials that can remember a primary shape and can return to this primary shape from a deformed secondary shape when given an appropriate stimulus. This property allows them to be delivered in a compact form via minimally invasive surgeries in humans, and deployed to achieve complex final shapes. Here we review the various biomedical applications of SMPs and the challenges they face with respect to actuation and biocompatibility. While shape memory behavior has been demonstrated with heat, light and chemical environment, here we focus our discussion on thermally stimulated SMPs.

  20. Biomedical applications of thermally activated shape memory polymers†

    PubMed Central

    Small, Ward; Singhal, Pooja; Wilson, Thomas S.

    2011-01-01

    Shape memory polymers (SMPs) are smart materials that can remember a primary shape and can return to this primary shape from a deformed secondary shape when given an appropriate stimulus. This property allows them to be delivered in a compact form via minimally invasive surgeries in humans, and deployed to achieve complex final shapes. Here we review the various biomedical applications of SMPs and the challenges they face with respect to actuation and biocompatibility. While shape memory behavior has been demonstrated with heat, light and chemical environment, here we focus our discussion on thermally stimulated SMPs. PMID:21258605

  1. The Solar Thermal Design Assistance Center report of its activities and accomplishments in Fiscal Year 1993

    SciTech Connect

    Menicucci, D.F.

    1994-03-01

    The Solar Thermal Design Assistance Center (STDAC) at Sandia National Laboratories is a resource provided by the US Department of Energy`s Solar Thermal Program. Its major objectives are to accelerate the use of solar thermal systems through (a) direct technical assistance to users, (b) cooperative test, evaluation, and development efforts with private industry, and (c) educational outreach activities. This report outlines the major activities and accomplishments of the STDAC in Fiscal Year 1993. The report also contains a comprehensive list of persons who contacted the STDAC by telephone for information or technical consulting.

  2. The thermal hysteresis activity of the type I antifreeze protein: A statistical mechanics model

    NASA Astrophysics Data System (ADS)

    Li, Li-Fen; Liang, X. X.; Li, Q. Z.

    2009-04-01

    Based on the adsorption-inhibition theory, a statistical mechanics model is proposed to investigate the thermal hysteresis activity of the type I antifreeze protein. The thermal hysteresis activity is evaluated by determining the AFP molecule coverage rate on the ice surface and the Gibbs function of the system. As examples, the calculated results for the thermal hysteresis temperatures of AFP9, HPLC-6(TTTT) and AAAA2kE as functions of the concentration of the AFP solution are obtained and discussed. The theoretical results are in agreement with the experimental data.

  3. Langevin simulation of thermally activated magnetization reversal in nanoscale pillars

    SciTech Connect

    Brown, Gregory; Novotny, M. A.; Rikvold, Per Arne

    2001-10-01

    Numerical solutions of the Landau-Lifshitz-Gilbert micromagnetic model incorporating thermal fluctuations and dipole-dipole interactions (calculated by the fast multipole method) are presented for systems composed of nanoscale iron pillars of dimension 9nm x 9nm x 150nm. Hysteresis loops generated under sinusoidally varying fields are obtained, while the coercive field is estimated to be 1979{+-}14 Oe using linear field sweeps at T=0 K. Thermal effects are essential to the relaxation of magnetization trapped in a metastable orientation, such as happens after a rapid reversal of an external magnetic field less than the coercive value. The distribution of switching times is compared to a simple analytic theory that describes reversal with nucleation at the ends of the nanomagnets. Results are also presented for arrays of nanomagnets oriented perpendicular to a flat substrate. Even at a separation of 300 nm, where the field from neighboring pillars is only {approx}1 Oe, the interactions have a significant effect on the switching of the magnets.

  4. Simulation of passive thermal management system for lithium-ion battery packs

    NASA Astrophysics Data System (ADS)

    Mills, Andrew; Al-Hallaj, Said

    A passive thermal management system that uses a phase change material (PCM) is designed and simulated for a lithium-ion (Li-ion) laptop battery pack. The problem of low thermal conductivity of the PCM was significantly improved by impregnating an expanded graphite (EG) matrix with the PCM. The heat generation rate for a commercial 186502.2 Ah Li-ion battery was experimentally measured for various constant power discharges. Simulation of the battery pack, composed of six Li-ion batteries, shows that safe operation of the battery pack during the most extreme case requires the volume of the battery pack be almost doubled to fit sufficient PCM in the pack. Improving the properties of the PCM composite have the potential to significantly reduce the volume increase in comparison to the original battery pack volume.

  5. On-chip thermal management of hotspots using a perspiration nanopatch

    NASA Astrophysics Data System (ADS)

    Narayanan, Shankar; Fedorov, Andrei G.; Joshi, Yogendra K.

    2010-07-01

    A cooling mechanism based on evaporation from thin liquid films is utilized for thermal management of hotspots combining efficient heat and mass transfer techniques. Dissipation of large heat fluxes from small form-factor areas is made possible by minimizing the thermal resistance across the evaporating liquid film. This is achieved by maintaining a very thin film (~15 µm) of coolant by capillary confinement using a nano-porous membrane (~10 µm). At the same time, evaporation is promoted by using jet impingement of dry air on the membrane. Based on these underlying ideas, a MEMS device called a 'perspiration nanopatch' is presented. The design and fabrication process of this micro-fluidic device is described along with experimental performance characterization under different operating conditions. Dissipation of heat fluxes in excess of 600 W cm-2 is demonstrated with heat transfer coefficients approaching 0.1 MW m-2 K-1 for surface temperatures well below the saturation temperature of the working fluid.

  6. Temperature distribution in a layer of an active thermal insulation system heated by a gas burner

    SciTech Connect

    Maruyama, Shigenao . Inst. of Fluid Science); Shimizu, Naotaka . Dept. of Mechanical Engineering)

    1993-12-01

    The temperature distribution in a layer of an active thermal insulation system was measured. A semitransparent porous layer was heated by a gas burner, and air was injected from the back face of the layer. The temperature in the layer was measured by thermocouples. The temperature distributions were compared with numerical solutions. The thermal penetration depth of the active thermal insulation layer with gas injection can be reduced to 3 mm. When the surface temperature of a conventional insulation layer without gas injection reached 1,500 K, the temperature at the back surface of a 10-mm-thick layer reached 600 K. The transient temperature of the active thermal insulation reached a steady state very quickly compared with that of the conventional insulation. These characteristics agreed qualitatively with the numerical solutions.

  7. Influence of Sulfur Fertilization on the Antioxidant Activities of Onion Juices Prepared by Thermal Treatment.

    PubMed

    Koh, Eunmi; Surh, Jeonghee

    2016-06-01

    Two onions (Sulfur-1 and Sulfur-4) cultivated with different sulfur applications were thermally processed to elucidate the effects of heat treatment on browning index and antioxidant activity. Sulfur-4 onion had higher sulfur content compared with the Sulfur-1 onion. After thermal processing, browning intensity was different between the two onions juices, with lower values observed for Sulfur-4 onion juice. This suggests that sulfur inhibits the Maillard browning reaction. The total reducing capacity of the juices increased at higher thermal processing temperatures; however, it was also lower in the Sulfur-4 onion juice. This suggests that the heat treatment of onions enhanced their antioxidant activity, but the effect was offset in the Sulfur-4 onion juice presumably due to higher sulfur content. This study indicates that sulfur, a core element for the functionality of onions, can decrease the antioxidant activity of thermally processed onions because of its potential as a Maillard reaction inhibitor. PMID:27390734

  8. Influence of Sulfur Fertilization on the Antioxidant Activities of Onion Juices Prepared by Thermal Treatment

    PubMed Central

    Koh, Eunmi; Surh, Jeonghee

    2016-01-01

    Two onions (Sulfur-1 and Sulfur-4) cultivated with different sulfur applications were thermally processed to elucidate the effects of heat treatment on browning index and antioxidant activity. Sulfur-4 onion had higher sulfur content compared with the Sulfur-1 onion. After thermal processing, browning intensity was different between the two onions juices, with lower values observed for Sulfur-4 onion juice. This suggests that sulfur inhibits the Maillard browning reaction. The total reducing capacity of the juices increased at higher thermal processing temperatures; however, it was also lower in the Sulfur-4 onion juice. This suggests that the heat treatment of onions enhanced their antioxidant activity, but the effect was offset in the Sulfur-4 onion juice presumably due to higher sulfur content. This study indicates that sulfur, a core element for the functionality of onions, can decrease the antioxidant activity of thermally processed onions because of its potential as a Maillard reaction inhibitor. PMID:27390734

  9. Description of data base management activities

    NASA Technical Reports Server (NTRS)

    1983-01-01

    ARC's current and future data processing needs have been identified and defined. Requirements for improved data processing capabilities are listed: (1) Centralized control of system data files. Establish a DBA/data base administrator position with responsibility for management of the Centers numerous data bases; (2) Programmer tools to improve efficiency of performance; (3) Direct and timely access to information. Presently, the user submits query requests to the data processing department where they are prioritized with other queries and then batch processed using a report generator; (4) On line data entry. With the merger of the Dryden facility with ARC on line data entry, edit and updates have become mandatory for timely operation and reporting. A DBMS software package was purchased to meet the above requirements.

  10. Modeling and Simulation of Phonon Transport at the Nanoscale for Optimum Thermal Management

    NASA Astrophysics Data System (ADS)

    Mao, Rui

    Recent progress in nanostructured materials synthesis and device fabrication technology has brought the need for thermal analysis and power management to the forefront. In this thesis, we investigate the phonon transport in the nanoscale through theoretical modeling and simulation for the optimum thermal management. Due to the superior electrical and thermal properties of graphene, the thermal transport of graphene/dielectric contact is first studied to provide better a understanding of phonon interactions and heat dissipation at nanoscale graphene interfaces. Using calculations from first principles and the Landauer approach for phonon transport, we calculated the Kapitza resistance in selected multilayer graphene/dielectric heterojunctions (hexagonal BN and wurtzite SiC) and demonstrate (i) the resistance variability (˜50--700x10 -10 m2K/W) induced by vertical coupling, dimensionality, and atomistic structure of the system and (ii) the ability of understanding the intensity of the thermal transmittance in terms of the phonon distribution at the interface. As a natural extension, thermal properties in the metal/graphene (Gr) systems are analyzed by using an atomistic phonon transport model based on Landauer formalism and first-principles calculations. The specific structures under investigation include chemisorbed Ni(111)/Gr, physisorbed Cu(111)/Gr and Au(111)/Gr, as well as Pd(111)/Gr with intermediate characteristics. Calculated results illustrate a strong dependence of thermal transfer on the details of interfacial microstructures. In particular, it is shown that the chemisorbed case provides a generally smaller interfacial thermal resistance than the physisorbed one due to the stronger bonding. However, our calculation also indicates that the weakly chemisorbed interface of Pd/Gr may be an exception, with the largest thermal resistance among the considered. Further examination of the electrostatic potential and interatomic force constants reveals that the

  11. Physicochemical and porosity characteristics of thermally regenerated activated carbon polluted with biological activated carbon process.

    PubMed

    Dong, Lihua; Liu, Wenjun; Jiang, Renfu; Wang, Zhansheng

    2014-11-01

    The characteristics of thermally regenerated activated carbon (AC) polluted with biological activated carbon (BAC) process were investigated. The results showed that the true micropore and sub-micropore volume, pH value, bulk density, and hardness of regenerated AC decreased compared to the virgin AC, but the total pore volume increased. XPS analysis displayed that the ash contents of Al, Si, and Ca in the regenerated AC respectively increased by 3.83%, 2.62% and 1.8%. FTIR spectrum showed that the surface functional groups of virgin and regenerated AC did not change significantly. Pore size distributions indicated that the AC regeneration process resulted in the decrease of micropore and macropore (D>10 μm) volume and the increase of mesopore and macropore (0.1 μm

  12. Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

    NASA Technical Reports Server (NTRS)

    Emrich, William

    2013-01-01

    A key technology element in Nuclear Thermal Propulsion is the development of fuel materials and components which can withstand extremely high temperatures while being exposed to flowing hydrogen. NTREES provides a cost effective method for rapidly screening of candidate fuel components with regard to their viability for use in NTR systems. The NTREES is designed to mimic the conditions (minus the radiation) to which nuclear rocket fuel elements and other components would be subjected to during reactor operation. The NTREES consists of a water cooled ASME code stamped pressure vessel and its associated control hardware and instrumentation coupled with inductive heaters to simulate the heat provided by the fission process. The NTREES has been designed to safely allow hydrogen gas to be injected into internal flow passages of an inductively heated test article mounted in the chamber.

  13. Thermal energy storage

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The planning and implementation of activities associated with lead center management role and the technical accomplishments pertaining to high temperature thermal energy storage subsystems are described. Major elements reported are: (1) program definition and assessment; (2) research and technology development; (3) industrial storage applications; (4) solar thermal power storage applications; and (5) building heating and cooling applications.

  14. Analysis of Sensory/Active Piezoelectric Composite Structures in Thermal Environments

    NASA Technical Reports Server (NTRS)

    Lee, Ho-Jun; Saravanos, Dimitris A.

    1996-01-01

    Although there has been extensive development of analytical methods for modeling the behavior of piezoelectric structures, only a limited amount of research has been performed concerning the implications of thermal effects on both the active and sensory response of smart structures. Thermal effects become important when the piezoelectric structure has to operate in either extremely hot or cold temperature environments. Consequently, the purpose of this paper is to extend the previously developed discrete layer formulation of Saravanos and Heyliger to account for the coupled mechanical, electrical, and thermal response in modern smart composite beams. The mechanics accounts for thermal effects which may arise in the elastic and piezoelectric media at the material level through the constitutive equations. The displacements, electric potentials, and temperatures are introduced as state variables, allowing them to be modeled as variable fields through the laminate thickness. This unified representation leads to an inherent capability to model both the active compensation of thermal distortions in smart structures and the resultant sensory voltage when thermal loads are applied. The corresponding finite element formulation is developed and numerical results demonstrate the ability to model both the active and sensory modes of composite beams with heterogeneous plies with attached piezoelectric layers under thermal loadings.

  15. Coupled Thermal and Water Management in Polymer-Electrolyte FuelCells

    SciTech Connect

    Weber, Adam Z.; Newman, John

    2006-11-01

    Thermal and water management are intricately coupled in polymer-electrolyte fuel cells. In this paper, we simulate fuel-cell performance and account for nonisothermal phenomena. The transport of water due to a temperature gradient and its associated effects on performance are described, with the increase of reactant dilution by the water-vapor partial pressure being the most dominant. In addition, simulations are undergone to find the optimum operating temperature and maximum power density as a function of external heat-transfer coefficient. The shape of the optimization curves and the magnitudes of the nonisothermal phenomena are also detailed and explained.

  16. Thermal Management Solutions Using Electron Tunneling Through a Nano-Scale Vacuum Gap

    NASA Astrophysics Data System (ADS)

    Magdych, Jim; Cox, Isaiah W.

    2004-02-01

    Requirements for cooling and power consumption in space platforms are subject to significantly greater constraints than the requirements for terrestrial applications. Existing cooling systems incorporate various mechanisms including thermoelectric (Peltier) cooling elements, radiative cooling, and phase-change compressor-based systems. This paper outlines an alternative mechanism currently in development called ``thermotunneling''. This mechanism exploits electron tunneling across a vacuum gap of ~10nm to effect a temperature differential with high efficiency. When complete, these devices (``Cool Chips'') are expected to offer a compact, lightweight, low maintenance and highly efficient (in excess of 50% of Carnot Efficiency) thermal management solution ideally suited for the needs of aerospace applications.

  17. Managing the Mars Science Laboratory Thermal Vacuum Test for Safety and Success

    NASA Technical Reports Server (NTRS)

    Evans, Jordan P.

    2010-01-01

    The Mars Science Laboratory is a NASA/JPL mission to send the next generation of rover to Mars. Originally slated for launch in 2009, development problems led to a delay in the project until the next launch opportunity in 2011. Amidst the delay process, the Launch/Cruise Solar Thermal Vacuum Test was undertaken as risk reduction for the project. With varying maturity and capabilities of the flight and ground systems, undertaking the test in a safe manner presented many challenges. This paper describes the technical and management challenges and the actions undertaken that led to the ultimate safe and successful execution of the test.

  18. Active listening: The key of successful communication in hospital managers

    PubMed Central

    Jahromi, Vahid Kohpeima; Tabatabaee, Seyed Saeed; Abdar, Zahra Esmaeili; Rajabi, Mahboobeh

    2016-01-01

    Introduction One of the important causes of medical errors and unintentional harm to patients is ineffective communication. The important part of this skill, in case it has been forgotten, is listening. The objective of this study was to determine whether managers in hospitals listen actively. Methods This study was conducted between May and June 2014 among three levels of managers at teaching hospitals in Kerman, Iran. Active Listening skill among hospital managers was measured by self-made Active Listening Skill Scale (ALSS), which consists of the key elements of active listening and has five subscales, i.e., Avoiding Interruption, Maintaining Interest, Postponing Evaluation, Organizing Information, and Showing Interest. The data were analyzed by IBM-SPSS software, version 20, and the Pearson product-moment correlation coefficient, the chi-squared test, and multiple linear regressions. Results The mean score of active listening in hospital managers was 2.32 out of 3.The highest score (2.27) was obtained by the first-level managers, and the top managers got the lowest score (2.16). Hospital mangers were best in showing interest and worst in avoiding interruptions. The area of employment was a significant predictor of avoiding interruption and the managers’ gender was a strong predictor of skill in maintaining interest (p < 0.05). The type of management and education can predict postponing evaluation, and the length of employment can predict showing interest (p < 0.05). Conclusion There is a necessity for the development of strategies to create more awareness among the hospital managers concerning their active listening skills. PMID:27123221

  19. Activity-Based Costing: A Cost Management Tool.

    ERIC Educational Resources Information Center

    Turk, Frederick J.

    1993-01-01

    In college and university administration, overhead costs are often charged to programs indiscriminately, whereas the support activities that underlie those costs remain unanalyzed. It is time for institutions to decrease ineffective use of resources. Activity-based management attributes costs more accurately and can improve efficiency. (MSE)

  20. Intrauterine resuscitation: active management of fetal distress.

    PubMed

    Thurlow, J A; Kinsella, S M

    2002-04-01

    Acute fetal distress in labour is a condition of progressive fetal asphyxia with hypoxia and acidosis. It is usually diagnosed by finding characteristic features in the fetal heart rate pattern, wherever possible supported by fetal scalp pH measurement. Intrauterine resuscitation consists of applying specific measures with the aim of increasing oxygen delivery to the placenta and umbilical blood flow, in order to reverse hypoxia and acidosis. These measures include initial left lateral recumbent positioning followed by right lateral or knee-elbow if necessary, rapid intravenous infusion of a litre of non-glucose crystalloid, maternal oxygen administration at the highest practical inspired percentage, inhibition of uterine contractions usually with subcutaneous or intravenous terbutaline 250 microg, and intra-amniotic infusion of warmed crystalloid solution. Specific manoeuvres for umbilical cord prolapse are also described. Intrauterine resuscitation may be used as part of the obstetric management of labour, while preparing for caesarean delivery for fetal distress, or at the time of establishment of regional analgesia during labour in the compromised fetus. The principles may also be applied during inter-hospital transfers of sick or labouring parturients. PMID:15321562

  1. Using Sales Management Students to Manage Professional Selling Students in an Innovative Active Learning Project

    ERIC Educational Resources Information Center

    Young, Joyce A.; Hawes, Jon M.

    2013-01-01

    This paper describes an application of active learning within two different courses: professional selling and sales management. Students assumed the roles of sales representatives and sales managers for an actual fund-raiser--a golf outing--sponsored by a student chapter of the American Marketing Association. The sales project encompassed an…

  2. Removal of daytime thermal deformations in the GBT active surface via out-of-focus holography

    NASA Astrophysics Data System (ADS)

    Hunter, T. R.; Mello, M.; Nikolic, B.; Mason, B. S.; Schwab, F. R.; Ghigo, F. D.; Dicker, S. R.

    2009-01-01

    The 100-m diameter Green Bank Telescope (GBT) was built with an active surface of 2209 actuators in order to achieve and maintain an accurate paraboloidal shape. While much of the large-scale gravitational deformation of the surface can be described by a finite element model, a significant uncompensated gravitational deformation exists. In recent years, the elevation-dependence of this residual deformation has been successfully measured during benign nighttime conditions using the out-of-focus (OOF) holography technique (Nikolic et al, 2007, A&A 465, 685). Parametrized by a set of Zernike polynomials, the OOF model correction was implemented into the active surface and has been applied during all high frequency observations since Fall 2006, yielding a consistent gain curve that is constant with elevation. However, large-scale thermal deformation of the surface has remained a problem for daytime high-frequency observations. OOF holography maps taken throughout a clear winter day indicate that surface deformations become significant whenever the Sun is above 10 degrees elevation, but that they change slowly while tracking a single source. In this paper, we describe a further improvement to the GBT active surface that allows an observer to measure and compensate for the thermal surface deformation using the OOF technique. In order to support high-frequency observers, "AutoOOF" is a new GBT Astrid procedure that acquires a quick set of in-focus and out-of-focus on-the-fly continuum maps on a quasar using the currently active receiver. Upon completion of the maps, the data analysis software is launched automatically which produces and displays the surface map along with a set of Zernike coefficients. These coefficients are then sent to the active surface manager which combines them with the existing gravitational Zernike terms and FEM in order to compute the total active surface correction. The end-to-end functionality has been tested on the sky at Q-Band and Ka

  3. Thermal biology, population fluctuations and implications of temperature extremes for the management of two globally significant insect pests.

    PubMed

    Nyamukondiwa, Casper; Weldon, Christopher W; Chown, Steven L; le Roux, Peter C; Terblanche, John S

    2013-12-01

    The link between environmental temperature, physiological processes and population fluctuations is a significant aspect of insect pest management. Here, we explore how thermal biology affects the population abundance of two globally significant pest fruit fly species, Ceratitis capitata (medfly) and C. rosa (Natal fruit fly), including irradiated individuals and those expressing a temperature sensitive lethal (tsl) mutation that are used in the sterile insect technique. Results show that upper and lower lethal temperatures are seldom encountered at the field sites, while critical minimum temperatures for activity and lower developmental thresholds are crossed more frequently. Estimates of abundance revealed that C. capitata are active year-round, but abundance declines markedly during winter. Temporal autocorrelation of average fortnightly trap captures and of development time, estimated from an integrated model to calculate available degree days, show similar seasonal lags suggesting that population increases in early spring occur after sufficient degree-days have accumulated. By contrast, population collapses coincide tightly with increasing frequency of low temperature events that fall below critical minimum temperatures for activity. Individuals of C. capitata expressing the tsl mutation show greater critical thermal maxima and greater longevity under field conditions than reference individuals. Taken together, this evidence suggests that low temperatures limit populations in the Western Cape, South Africa and likely do so elsewhere. Increasing temperature extremes and warming climates generally may extend the season over which these species are active, and could increase abundance. The sterile insect technique may prove profitable as climates change given that laboratory-reared tsl flies have an advantage under warmer conditions. PMID:24080125

  4. Thermal Decomposition of Benzyl Radical via Multiple Active Pathways

    NASA Astrophysics Data System (ADS)

    Buckingham, Grant; Robichaud, David; Ormond, Thomas; Nimlos, Mark R.; Daily, John W.; Ellison, Barney

    2014-06-01

    The thermal decomposition of benzyl radical (C6H5CH2) has been investigated using a combination infrared absorption spectroscopy in a neon matrix and 118.2 (10.487 eV) photoionization mass spectrometry. Both techniques are coupled with a heated tubular reactor to allow temperature control over the decomposition to indicate relative barrier heights of fragmentation pathways. Three possible chemical mechanisms have been considered. 1) Ring expansion to cycloheptatrienyl radical (C7H7) with subsequent breakdown to HCCH and C5H5, 2) isomerization to the substituted five-membered ring fulvenallene (C5H4=C=CH2), which is of interest to kinetic theorists and finally 3) hydrogen shift to form methyl-substituted phenyl radical, which can then form ortho-benzyne, diacetylene and other fragments. Benzyl radical is generated from two precursors, C6H5CH2CH3 and C6H5CH2Br, and both lead to the appearance of HCCH and C5H5. At slightly hotter temperatures peaks are observed at m/z 90, presumed to be C5H4=C=CH2, and 89, potentially the substituted propargyl C5H4=C=CH. Additionally, decomposition of isotopically substituted parent molecules C6H5CD2CD3 and C6D5CH2CH3 indicates C7H7 as an intermediate due to H/D ratios in fragment molecules.

  5. Distribution of Thermally Activated Plastic Events in a Flowing Glass

    NASA Astrophysics Data System (ADS)

    Rodney, David; Schuh, Christopher

    2009-06-01

    The potential energy landscape of a flowing metallic glass is revealed using the activation-relaxation technique. For a two-dimensional Lennard-Jones system initially deformed into a steady-state condition through quasistatic shear, the distribution of activation energies is shown to contain a large fraction of low-energy barriers, consistent with a highly nonequilibrium flow state. The distribution of plastic strains has a fundamentally different shape than that obtained during quasistatic simulations, exhibiting a peak at finite strain and, after elastic unloading, a nonzero mean plastic strain that evidences a polarization of the flow state. No significant correlation is found between the activation energy of a plastic event and its associated plastic strain.

  6. Thermal Inactivation of Newcastle Disease Virus I. Coupled Inactivation Rates of Hemagglutinating and Neuraminidase Activities

    PubMed Central

    Pierce, John S.; Haywood, A. M.

    1973-01-01

    The thermal stability of Newcastle disease virus has been characterized in terms of the rate constants for inactivation of hemagglutinating activity (HA), neuraminidase activity (NA), and infectivity. Inactivation of HA results in the concomitant loss of NA. Infectivity, however, is much more thermolabile. Disintegration of the virus particle is not responsible for the identical rate constants for inactivation of HA and NA, nor is their parallel inactivation uncoupled in envelope fragments produced by pretreating the virus with phospholipase-C. The data indicate that a common envelope factor(s) can influence the thermal stability of both activities. PMID:4734647

  7. [Active career management needed for female doctors].

    PubMed

    Maas, Angela H E M; ter Braak, Edith W M T; Verbon, Annelies

    2015-01-01

    For more than 15 years two-thirds of medical students have been women. Despite this, they represent a minority (16-25 %) of professors in academic medicine. There is still a major gender gap to the disadvantage of women in leading positions in academia, with women earning only 80% of the salary of their male counterparts and fewer opportunities for scientific grants. Recent studies have shown that career ambition among men and women in medicine is comparable. However, successful women more often doubt their own achievements than men do. This is known as the 'imposter phenomenon' and acts as a barrier to career progression. Female leadership should be more actively promoted and encouraged to establish the diversity and creativity that we need in our current healthcare system. PMID:26959735

  8. Design and testing of a high power spacecraft thermal management system

    NASA Technical Reports Server (NTRS)

    Mccabe, Michael E., Jr.; Ku, Jentung; Benner, Steve

    1988-01-01

    The design and test results are presented of an ammonia hybrid capillary pumped loop thermal control system which could be used for heat acquisition and transport on future large space platforms and attached payloads, such as those associated with the NASA Space Station. The High Power Spacecraft Thermal Management System (HPSTM) can operate as either a passive, capillary pumped two phase thermal control system, or, when additional pressure head is required, as a mechanically pumped loop. Testing has shown that in the capillary mode, the HPSTM evaporators can acquire a total heat load of between 600 W and 24 kW, transported over 10 meters, at a maximum heat flux density of 4.3 W/sq cm. With the mechanical pump circulating the ammonia, a heat acquisition potential of 52 kW was demonstrated for 15 minutes without an evaporator failure. These results represent a significant improvement over the maximum transport capability previously displayed in other capillary systems. The HPSTM system still retains the proven capillary capabilities of heat load sharing and flow control between evaporator plates, rapid power cycling, and nonuniform heating in both the capillary and hybrid operating modes.

  9. CAE for thermal management of aerospace electronic boards using the BETAsoft program

    NASA Technical Reports Server (NTRS)

    Bobish, Kimberly

    1995-01-01

    Aerospace electronic boards require special attention to thermal management due to constraints such as their need to be light, small, and maintain high power densities. Also, cooling is mainly through conductive and radiative modes with minor or negligible convective cooling. Due to these particular requirements, thermal design has become an integrated part of the electronic design process in order to avoid expensive repeat prototyping and to ensure high reliability. To achieve high speed simulations, the BETAsoft code uses semi-empirical formulations and an advanced finite difference scheme that incorporates local adaptive grids. Detailed conduction, convection and radiation heat transfer is considered. Various benchmark verifications of the software simulation compared to infrared images typically prove to be within 10% of each other. The thermal analysis of a sample avionic card in a natural convection environment is shown. Then, the individual effects of attaching metal screws to the casing, increasing radiative emissivities of the casing, increasing the conductance of the wedge lock, adding an aluminum core to the board, adding metal strips in board layers, inserting conduction pads under components, and adding heat sinks to components are demonstrated.

  10. A nonventing cooling system for space environment extravehicular activity, using radiation and regenerable thermal storage

    NASA Technical Reports Server (NTRS)

    Bayes, Stephen A.; Trevino, Luis A.; Dinsmore, Craig E.

    1988-01-01

    This paper outlines the selection, design, and testing of a prototype nonventing regenerable astronaut cooling system for extravehicular activity space suit applications, for mission durations of four hours or greater. The selected system consists of the following key elements: a radiator assembly which serves as the exterior shell of the portable life support subsystem backpack; a layer of phase change thermal storage material, n-hexadecane paraffin, which acts as a regenerable thermal capacitor; a thermoelectric heat pump; and an automatic temperature control system. The capability for regeneration of thermal storage capacity with and without the aid of electric power is provided.

  11. Novel thermal management system design methodology for power lithium-ion battery

    NASA Astrophysics Data System (ADS)

    Nieto, Nerea; Díaz, Luis; Gastelurrutia, Jon; Blanco, Francisco; Ramos, Juan Carlos; Rivas, Alejandro

    2014-12-01

    Battery packs conformed by large format lithium-ion cells are increasingly being adopted in hybrid and pure electric vehicles in order to use the energy more efficiently and for a better environmental performance. Safety and cycle life are two of the main concerns regarding this technology, which are closely related to the cell's operating behavior and temperature asymmetries in the system. Therefore, the temperature of the cells in battery packs needs to be controlled by thermal management systems (TMSs). In the present paper an improved design methodology for developing TMSs is proposed. This methodology involves the development of different mathematical models for heat generation, transmission, and dissipation and their coupling and integration in the battery pack product design methodology in order to improve the overall safety and performance. The methodology is validated by comparing simulation results with laboratory measurements on a single module of the battery pack designed at IK4-IKERLAN for a traction application. The maximum difference between model predictions and experimental temperature data is 2 °C. The models developed have shown potential for use in battery thermal management studies for EV/HEV applications since they allow for scalability with accuracy and reasonable simulation time.

  12. Characterization of an Active Thermal Erosion Site, Caribou Creek, Alaska

    NASA Astrophysics Data System (ADS)

    Busey, R.; Bolton, W. R.; Cherry, J. E.; Hinzman, L. D.

    2013-12-01

    The goal of this project is to estimate volume loss of soil over time from this site, provide parameterizations on erodibility of ice rich permafrost and serve as a baseline for future landscape evolution simulations. Located in the zone of discontinuous permafrost, the interior region of Alaska (USA) is home to a large quantity of warm, unstable permafrost that is both high in ice content and has soil temperatures near the freezing point. Much of this permafrost maintains a frozen state despite the general warming air temperature trend in the region due to the presence of a thick insulating organic mat and a dense root network in the upper sub-surface of the soil column. At a rapidly evolving thermo-erosion site, located within the Caribou-Poker Creeks Research Watershed (part of the Bonanza Creek LTER) near Chatanika, Alaska (N65.140, W147.570), the protective organic layer and associated plants were disturbed by an adjacent traditional use trail and the shifting of a groundwater spring. These triggers have led to rapid geomorphological change on the landscape as the soil thaws and sediment is transported into the creek at the valley bottom. Since 2006 (approximately the time of initiation), the thermal erosion has grown to 170 meters length, 3 meters max depth, and 15 meters maximum width. This research combines several data sets: DGPS survey, imagery from an extremely low altitude pole-based remote sensing (3 to 5 meters above ground level), and imagery from an Unmanned Aerial System (UAS) at about 60m altitude.

  13. Self-healing polymers and composites based on thermal activation

    NASA Astrophysics Data System (ADS)

    Wang, Ying; Bolanos, Ed; Wudl, Fred; Hahn, Thomas; Kwok, Nathan

    2007-04-01

    Structural polymer composites are susceptible to premature failure in the form of microcracks in the matrix. Although benign initially when they form, these matrix cracks tend to coalesce and lead in service to critical damage modes such as ply delamination. The matrix cracks are difficult to detect and almost impossible to repair because they form inside the composite laminate. Therefore, polymers with self-healing capability would provide a promising potential to minimize maintenance costs while extending the service lifetime of composite structures. In this paper we report on a group of polymers and their composites which exhibit mendable property upon heating. The failure and healing mechanisms of the polymers involve Diels-Alder (DA) and retro-Diels-Alder (RDA) reactions on the polymer back-bone chain, which are thermally reversible reactions requiring no catalyst. The polymers exhibited good healing property in bulk form. Composite panels were prepared by sandwiching the monomers between carbon fiber fabric layers and cured in autoclave. Microcracks were induced on the resin-rich surface of composite with Instron machine at room temperature by holding at 1% strain for 1 min. The healing ability of the composite was also demonstrated by the disappearance of microcracks after heating. In addition to the self-healing ability, the polymers and composites also exhibited shape memory property. These unique properties may provide the material multi-functional applications. Resistance heating of traditional composites and its applicability in self-healing composites is also studied to lay groundwork for a fully integrated self-healing composite.

  14. Passive and active adaptive management: Approaches and an example

    USGS Publications Warehouse

    Williams, B.K.

    2011-01-01

    Adaptive management is a framework for resource conservation that promotes iterative learning-based decision making. Yet there remains considerable confusion about what adaptive management entails, and how to actually make resource decisions adaptively. A key but somewhat ambiguous distinction in adaptive management is between active and passive forms of adaptive decision making. The objective of this paper is to illustrate some approaches to active and passive adaptive management with a simple example involving the drawdown of water impoundments on a wildlife refuge. The approaches are illustrated for the drawdown example, and contrasted in terms of objectives, costs, and potential learning rates. Some key challenges to the actual practice of AM are discussed, and tradeoffs between implementation costs and long-term benefits are highlighted. ?? 2010 Elsevier Ltd.

  15. Conjugation of type I antifreeze protein to polyallylamine increases thermal hysteresis activity.

    PubMed

    Can, Ozge; Holland, Nolan B

    2011-10-19

    Antifreeze proteins (AFPs) are ice binding proteins found in some plants, insects, and Antarctic fish allowing them to survive at subzero temperatures by inhibiting ice crystal growth. The interaction of AFPs with ice crystals results in a difference between the freezing and melting temperatures, termed thermal hysteresis, which is the most common measure of AFP activity. Creating antifreeze protein constructs that reduce the concentration of protein needed to observe thermal hysteresis activities would be beneficial for diverse applications including cold storage of cells or tissues, ice slurries used in refrigeration systems, and food storage. We demonstrate that conjugating multiple type I AFPs to a polyallylamine chain increases thermal hysteresis activity compared to the original protein. The reaction product is approximately twice as active when compared to the same concentration of free proteins, yielding 0.5 °C thermal hysteresis activity at 0.3 mM protein concentration. More impressively, the amount of protein required to achieve a thermal hysteresis of 0.3 °C is about 100 times lower when conjugated to the polymer (3 μM) compared to free protein (300 μM). Ice crystal morphologies observed in the presence of the reaction product are comparable to those of the protein used in the conjugation reaction. PMID:21905742

  16. Degradation of carbon tetrachloride in aqueous solution in the thermally activated persulfate system.

    PubMed

    Xu, Minhui; Gu, Xiaogang; Lu, Shuguang; Qiu, Zhaofu; Sui, Qian; Miao, Zhouwei; Zang, Xueke; Wu, Xiaoliang

    2015-04-01

    Thermal activation of persulfate (PS) has been identified to be effective in the destruction of organic pollutants. The feasibility of carbon tetrachloride (CT) degradation in the thermally activated PS system was evaluated. The experimental results showed that CT could be readily degraded at 50 °C with a PS concentration of 0.5M, and CT degradation and PS consumption followed the pseudo-first order kinetic model. Superoxide radical anion (O2(*-)) was the predominant radical species responsible for CT degradation and the split of CCl was proposed as the possible reaction pathways for CT degradation. The process of CT degradation was accelerated by higher PS dose and lower initial CT concentration. No obvious effect of the initial pH on the degradation of CT was observed in the thermally activated PS system. Cl(*-), HCO3(*-), and humic acid (HA) had negative effects on CT degradation. In addition, the degradation of CT in the thermally activated PS system could be significantly promoted by the solvents addition to the solution. In conclusion, the thermally activated PS process is a promising option in in-situ chemical oxidation/reduction remediation for degrading highly oxidized organic contaminants such as CT that is widely detected in contaminated sites. PMID:25544995

  17. Changes in thermal activity in the Rotorua geothermal field

    SciTech Connect

    Cody, A.D. ); Lumb, J.T. )

    1992-04-01

    During a period when geothermal fluid was being withdrawn for energy use at an increasing rate, the level of natural hydrothermal activity in the Rotorua geothermal field declined in an all-time low in the mid 1980s. total heatflow from a major hot-spring area fell by almost 50 percent, springs ceased their flow, and geysers displayed abnormal behavior consistent with a low aquifer pressure. since the enforced closure of bores within 1.5 km of Pohutu Geyser, sings of recovery, including a return to normal behavior of Pohutu and Waikorohihi Geysers, a resumption of activity at Kereru Geyser, and an increase in water flow from some springs are presented in this paper.

  18. Mechanisms and Management of Stress Fractures in Physically Active Persons

    PubMed Central

    Romani, William A.; Gieck, Joe H.; Perrin, David H.; Saliba, Ethan N.; Kahler, David M.

    2002-01-01

    Objective: To describe the anatomy of bone and the physiology of bone remodeling as a basis for the proper management of stress fractures in physically active people. Data Sources: We searched PubMed for the years 1965 through 2000 using the key words stress fracture, bone remodeling, epidemiology, and rehabilitation. Data Synthesis: Bone undergoes a normal remodeling process in physically active persons. Increased stress leads to an acceleration of this remodeling process, a subsequent weakening of bone, and a higher susceptibility to stress fracture. When a stress fracture is suspected, appropriate management of the injury should begin immediately. Effective management includes a cyclic process of activity and rest that is based on the remodeling process of bone. Conclusions/Recommendations: Bone continuously remodels itself to withstand the stresses involved with physical activity. Stress fractures occur as the result of increased remodeling and a subsequent weakening of the outer surface ofthe bone. Once a stress fracture is suspected, a cyclic management program that incorporates the physiology of bone remodeling should be initiated. The cyclic program should allow the physically active person to remove the source of the stress to the bone, maintain fitness, promote a safe return to activity, and permit the bone to heal properly. PMID:16558676

  19. Optimal allocation of thermodynamic irreversibility for the integrated design of propulsion and thermal management systems

    NASA Astrophysics Data System (ADS)

    Maser, Adam Charles

    More electric aircraft systems, high power avionics, and a reduction in heat sink capacity have placed a larger emphasis on correctly satisfying aircraft thermal management requirements during conceptual design. Thermal management systems must be capable of dealing with these rising heat loads, while simultaneously meeting mission performance. Since all subsystem power and cooling requirements are ultimately traced back to the engine, the growing interactions between the propulsion and thermal management systems are becoming more significant. As a result, it is necessary to consider their integrated performance during the conceptual design of the aircraft gas turbine engine cycle to ensure that thermal requirements are met. This can be accomplished by using thermodynamic subsystem modeling and simulation while conducting the necessary design trades to establish the engine cycle. However, this approach also poses technical challenges associated with the existence of elaborate aircraft subsystem interactions. This research addresses these challenges through the creation of a parsimonious, transparent thermodynamic model of propulsion and thermal management systems performance with a focus on capturing the physics that have the largest impact on propulsion design choices. This modeling environment, known as Cycle Refinement for Aircraft Thermodynamically Optimized Subsystems (CRATOS), is capable of operating in on-design (parametric) and off-design (performance) modes and includes a system-level solver to enforce design constraints. A key aspect of this approach is the incorporation of physics-based formulations involving the concurrent usage of the first and second laws of thermodynamics, which are necessary to achieve a clearer view of the component-level losses across the propulsion and thermal management systems. This is facilitated by the direct prediction of the exergy destruction distribution throughout the system and the resulting quantification of available

  20. Active Layer Thermal Response to Stream Water Temperatures

    NASA Astrophysics Data System (ADS)

    Cozzetto, K.; McKnight, D.

    2004-12-01

    The hyporheic zone is comprised of sediments below and adjacent to a stream through which stream water flows in and out. In polar regions, the shape, dimensions, physical and chemical characteristics of this zone are affected by the seasonal freezing and thawing of the active layer. One factor that may influence the active layer temperature regime is stream water temperature, both its absolute value and cyclic variations in its value. Many of the glacial meltwater streams in Taylor Valley in the McMurdo Dry Valleys of Antarctica, exhibit daily temperature patterns with lows of 0 or 1° C and highs of 10 or, on occasion, 15° C. Because the viscosity of water decreases significantly with increasing temperature, these daily maxima may increase infiltration and the exchange of water and heat between the stream and the hyporheic zone. To investigate the influence of stream water temperature and flow paths on the active layer temperature regime and vice versa, two conservative tracer injection experiments were conducted. Both took place in the same 200-meter reach, which was instrumented with temperature and conductivity probes. Both also took place at the same time of day during which the stream reaches its temperature maximum. However, in one experiment snow from a nearby patch was added to the stream to suppress the temperature maximum by 3° C from 10 to 7° C. The temperature data show that the snow addition slowed the rate of hyporheic zone warming and suppressed temperature increases in the hyporheic zone by 1-3° C when compared with the non-perturbation experiment. The electrical conductivity data indicate that during the snow addition experiment, the stream neither gained nor lost water while during the non-perturbation experiment, the stream lost water. These results suggest that the stream water cooling decreased infiltration and heat transfer into the hyporheic zone.

  1. Characteristics of Trailer Thermal Environment during Commercial Swine Transport Managed under U.S. Industry Guidelines

    PubMed Central

    Xiong, Yijie; Green, Angela; Gates, Richard S.

    2015-01-01

    Simple Summary Temperature and thermal conditions of the interior of a swine trailer during transport were monitored over a broad range of outdoor conditions (34 trips total) managed according to industry best practice (Transport Quality Assurance (TQA) guidelines (NPB, 2008)). For the outdoor temperature range of 5 °C (40 °F) to 27 °C (80 °F), generally acceptable trailer thermal conditions were observed according to the TQA. Beyond this outdoor temperature range, undesirable conditions within the trailer were prevalent. Areas for potential improvement in transport management were identified. Stops resulted in rapid increases in temperature, which could be beneficial during cooler outdoor temperatures, but detrimental for warmer outdoor temperatures. Abstract Transport is a critical factor in modern pork production and can seriously affect swine welfare. While previous research has explored thermal conditions during transport, the impact of extreme weather conditions on the trailer thermal environment under industry practices has not been well documented; and the critical factors impacting microclimate are not well understood. To assess the trailer microclimate during transport events, an instrumentation system was designed and installed at the central ceiling level, pig level and floor-level in each of six zones inside a commercial swine trailer. Transport environmental data from 34 monitoring trips (approximately 1–4 h in duration each) were collected from May, 2012, to February, 2013, with trailer management corresponding to the National Pork Board Transport Quality Assurance (TQA) guidelines in 31 of these trips. According to the TQA guidelines, for outdoor temperature ranging from 5 °C (40 °F) to 27 °C (80 °F), acceptable thermal conditions were observed based on the criteria that no more than 10% of the trip duration was above 35 °C (95 °F) or below 0 °C (32 °F). Recommended bedding, boarding and water application were sufficient in this range

  2. WAX ActiveLibrary: a tool to manage information overload.

    PubMed

    Hanka, R; O'Brien, C; Heathfield, H; Buchan, I E

    1999-11-01

    WAX Active-Library (Cambridge Centre for Clinical Informatics) is a knowledge management system that seeks to support doctors' decision making through the provision of electronic books containing a wide range of clinical knowledge and locally based information. WAX has been piloted in several regions in the United Kingdom and formally evaluated in 17 GP surgeries based in Cambridgeshire. The evaluation has provided evidence that WAX Active-Library significantly improves GPs' access to relevant information sources and by increasing appropriate patient management and referrals this might also lead to an improvement in clinical outcomes. PMID:10662094

  3. Chemical and thermal modulation of molecular motor activities

    NASA Astrophysics Data System (ADS)

    Hong, Weili

    Molecular motors of kinesin and dynein families are responsible for various intracellular activities, from long distance movement of organelles, vesicles, protein complexes, and mRNAs to powering mitotic processes. They can take nanometer steps using chemical energy from the hydrolysis of ATP (adenosine triphosphate), and their dysfunction is involved in many neurodegenerative diseases that require long distance transport of cargos. Here I report on the study of the properties of molecular motors at a single-molecule level using optical trappings. I first studied the inhibition properties of kinesin motors by marine natural compound adociasulfates. I showed that adociasulfates compete with microtubules for binding to kinesins and thus inhibit kinesins' activity. Although adociasulfates are a strong inhibitor for all kinesin members, they show a much higher inhibition effect for conventional kinesins than for mitotic kinesins. Thus adociasulfates can be used to specifically inhibit conventional kinesins. By comparing the inhibition of kinesins by two structurally similar adociasulfates, one can see that the negatively charged sulfate residue of adociasulfates can be replaced by other negative residues and thus make it possible for adociasulfate-derived compounds to be more cell permeable. Kinesins and dyneins move cargos towards opposite directions along a microtubule. Cargos with both kinesins and dyneins attached often move bidirectionally due to undergoing a tug-of-war between the oppositely moving kinesin and dynein motors. Here I studied the effect of temperature on microtubule-based kinesin and dynein motor transport. While kinesins' and dyneins' velocities are closely matched above 15 °C, below this temperature the dyneins' velocity decreases much faster than the kinesins'. The kinesins' and dyneins' forces do not measurably change with temperature. The results suggest that temperature has significant effects on bidirectional transport and can be used to

  4. Thermal Characterization of PZT Ceramics Obtained by Mechanically Activated Mixed Oxides Using Different Pb Sources

    NASA Astrophysics Data System (ADS)

    Rivera-Ruedas, G.; Ramírez-López, L. M.; Sánchez de Jesús, F.; Bolarín-Miró, A.; Muñoz-Saldaña, J.; Yáñez-Limón, J. M.

    2012-12-01

    In this study, three sets of PZT samples with compositions 57/43 and 55/45 (rhombohedral phase), 53/47 and 51/49 (tetragonal phase) prepared by mechanochemical activation of powder mixtures (during 4 h of milling) and thermal treatment (sintered at 1200 °C for 4 h) were thermally characterized. The three sets of compositions were prepared using different Pb sources (A-PbO, B-PbO2, and C-Pb3O4). The thermal characterization of sintered samples was carried out by photoacoustic spectroscopy and differential scanning calorimetry, to obtain the thermal diffusivity and specific heat ( c p ). The DSC thermograms also allowed the determination of the Curie temperature, and the thermal conductivity was calculated combining the results of the thermal diffusivity, specific heat, and density. The samples obtained with Pb3O4 showed a theoretical density higher than 95 %, whereas those obtained from PbO2 precursors showed a lower densification rate (around 89 %). The samples obtained with Pb3O4 with compositions 53/47 and 51/49 also showed the highest values of thermal diffusivity (7.3 ± 0.4) × 10-7m2· s-1 and (6.6 ± 0.3) × 10-7m2· s-1, respectively.

  5. Inter/intra granular exchange and thermal activation in nanoscale granular magnetic materials

    NASA Astrophysics Data System (ADS)

    Morrison, C.; Saharan, L.; Hrkac, G.; Schrefl, T.; Ikeda, Y.; Takano, K.; Miles, J. J.; Thomson, T.

    2011-09-01

    We explain the effect of inter/intra granular exchange coupling and thermal activation on the switching behavior of nano-scale granular magnetic materials. For an ideal, non-interacting granular system, the minimum switching field occurs at 45° from the easy axis of the grains. We show through simulation and measurements, using a CoCrPt oxide-segregated granular film as a model system, that there is a clear shift in the angle of applied field at which the minimum switching field occurs. This arises solely due to incoherent reversal induced by inter-granular exchange coupling or incoherency within larger grains, rather than thermal activation.

  6. Thermally activated delayed fluorescence evidence in non-bonding transition electron donor-acceptor molecules

    NASA Astrophysics Data System (ADS)

    Marghad, Ikbal; Clochard, M. C.; Ollier, N.; Wade, Travis L.; Aymes-Chodur, C.; Renaud, C.; Zissis, G.

    2015-09-01

    The exhibition of thermally activated delayed fluorescence on triazine derivative by the introduction of a nonbonding part is demonstrated. Two molecules containing triazine core as acceptor and carbazole part as donor has been synthesized and characterized. One of these molecules bears an additional nonbonding part by the means of a phenoxy group. The results indicated that the molecule bearing the nonbonding molecular part (phenoxy) exhibit thermally activated delayed fluorescence while not on molecule free of non-bonding group. The results are supported by, photoluminescence, spectral analysis time-resolved fluorescence and time-dependent density functional estimation

  7. Method to Increase Performance of Foil Bearings Through Passive Thermal Management

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert

    2013-01-01

    This invention is a new approach to designing foil bearings to increase their load capacity and improve their reliability through passive thermal management. In the present case, the bearing is designed in such a way as to prevent the carryover of lubricant from the exit of one sector to the inlet of the ensuing sector of the foil bearing. When such passive thermal management techniques are used, bearing load capacity is improved by multiples, and reliability is enhanced when compared to current foil bearings. This concept has recently been tested and validated, and shows that load capacity performance of foil bearings can be improved by a factor of two at relatively low speeds with potentially greater relative improvements at higher speeds. Such improvements in performance with respect to speed are typical of foil bearings. Additionally, operation of these newly conceived bearings shows much more reliability and repeatable performance. This trait can be exploited in machine design to enhance safety, reliability, and overall performance. Finally, lower frictional torque has been demonstrated when operating at lower (non-load capacity) loads, thus providing another improvement above the current state of the art. The objective of the invention is to incorporate features into a foil bearing that both enhance passive thermal management and temperature control, while at the same time improve the hydrodynamic (load capacity) performance of the foil bearing. Foil bearings are unique antifriction devices that can utilize the working fluid of a machine as a lubricant (typically air for turbines and motors, liquids for pumps), and as a coolant to remove excess energy due to frictional heating. The current state of the art of foil bearings utilizes forced cooling of the bearing and shaft, which represents poor efficiency and poor reliability. This invention embodies features that utilize the bearing geometry in such a manner as to both support load and provide an inherent and

  8. Integrated Modeling Activities for the James Webb Space Telescope: Structural-Thermal-Optical Analysis

    NASA Technical Reports Server (NTRS)

    Johnston, John D.; Howard, Joseph M.; Mosier, Gary E.; Parrish, Keith A.; McGinnis, Mark A.; Bluth, Marcel; Kim, Kevin; Ha, Kong Q.

    2004-01-01

    The James Web Space Telescope (JWST) is a large, infrared-optimized space telescope scheduled for launch in 2011. This is a continuation of a series of papers on modeling activities for JWST. The structural-thermal-optical, often referred to as STOP, analysis process is used to predict the effect of thermal distortion on optical performance. The benchmark STOP analysis for JWST assesses the effect of an observatory slew on wavefront error. Temperatures predicted using geometric and thermal math models are mapped to a structural finite element model in order to predict thermally induced deformations. Motions and deformations at optical surfaces are then input to optical models, and optical performance is predicted using either an optical ray trace or a linear optical analysis tool. In addition to baseline performance predictions, a process for performing sensitivity studies to assess modeling uncertainties is described.

  9. Efficient Management of Complex Striped Files in Active Storage

    SciTech Connect

    Piernas Canovas, Juan; Nieplocha, Jaroslaw

    2008-08-25

    Active Storage provides an opportunity for reducing the band- width requirements between the storage and compute elements of cur- rent supercomputing systems, and leveraging the processing power of the storage nodes used by some modern file systems. To achieve both objec- tives, Active Storage allows certain processing tasks to be performed directly on the storage nodes, near the data they manage. However, Active Storage must also support key requirements of scientific applications. In particular, Active Storage must be able to support striped files and files with complex formats (e.g., netCDF). In this paper, we describe how these important requirements can be addressed. The experimental results on a Lustre file system not only show that our proposal can re- duce the network traffic to near zero and scale the performance with the number of storage nodes, but also that it provides an efficient treatment of striped files and can manage files with complex data structures.

  10. Assessment and Accommodation of Thermal Expansion of the Internal Active Thermal Control System Coolant During Launch to On-Orbit Activation of International Space Station Elements

    NASA Technical Reports Server (NTRS)

    Edwards, J. Darryl; Ungar, Eugene K.; Holt, James M.; Turner, Larry D. (Technical Monitor)

    2001-01-01

    The International Space Station (ISS) employs an Internal Active Thermal Control System (IATCS) comprised of several single-phase water coolant loops. These coolant loops are distributed throughout the ISS pressurized elements. The primary element coolant loops (i.e., US Laboratory module) contain a fluid accumulator to accommodate thermal expansion of the system. Other element coolant loops are parasitic (i.e., Airlock), have no accumulator, and require an alternative approach to insure that the system Maximum Design Pressure (MDP) is not exceeded during the Launch to Activation phase. During this time the element loop is a stand alone closed individual system. The solution approach for accommodating thermal expansion was affected by interactions of system components and their particular limitations. The mathematical solution approach was challenged by the presence of certain unknown or not readily obtainable physical and thermodynamic characteristics of some system components and processes. The purpose of this paper is to provide a brief description of a few of the solutions that evolved over time, a novel mathematical solution to eliminate some of the unknowns or derive the unknowns experimentally, and the testing and methods undertaken.

  11. Assessment and Accommodation of Thermal Expansion of the Internal Active Thermal Control System Coolant During Launch to On-Orbit Activation of International Space Station Elements

    NASA Technical Reports Server (NTRS)

    Edwards, Darryl; Ungar, Eugene K.; Holt, James M.

    2002-01-01

    The International Space Station (ISS) employs an Internal Active Thermal Control System (IATCS) comprised of several single-phase water coolant loops. These coolant loops are distributed throughout the ISS pressurized elements. The primary element coolant loops (i.e. U.S. Laboratory module) contain a fluid accumulator to accomodate thermal expansion of the system. Other element coolant loops are parasitic (i.e. Airlock), have no accumulator, and require an alternative approach to insure that the system maximum design pressure (MDP) is not exceeded during the Launch to Activation (LTA) phase. During this time the element loops is a stand alone closed system. The solution approach for accomodating thermal expansion was affected by interactions of system components and their particular limitations. The mathematical solution approach was challenged by the presence of certain unknown or not readily obtainable physical and thermodynamic characteristics of some system components and processes. The purpose of this paper is to provide a brief description of a few of the solutions that evolved over time, a novel mathematical solution to eliminate some of the unknowns or derive the unknowns experimentally, and the testing and methods undertaken.

  12. ISS Internal Active Thermal Control System (IATCS) Coolant Remediation Project

    NASA Technical Reports Server (NTRS)

    Morrison, Russell H.; Holt, Mike

    2005-01-01

    The IATCS coolant has experienced a number of anomalies in the time since the US Lab was first activated on Flight 5A in February 2001. These have included: 1) a decrease in coolant pH, 2) increases in inorganic carbon, 3) a reduction in phosphate buffer concentration, 4) an increase in dissolved nickel and precipitation of nickel salts, and 5) increases in microbial concentration. These anomalies represent some risk to the system, have been implicated in some hardware failures and are suspect in others. The ISS program has conducted extensive investigations of the causes and effects of these anomalies and has developed a comprehensive program to remediate the coolant chemistry of the on-orbit system as well as provide a robust and compatible coolant solution for the hardware yet to be delivered. The remediation steps include changes in the coolant chemistry specification, development of a suite of new antimicrobial additives, and development of devices for the removal of nickel and phosphate ions from the coolant. This paper presents an overview of the anomalies, their known and suspected system effects, their causes, and the actions being taken to remediate the coolant.

  13. Thermally activated persulfate oxidation regeneration of NOM- and MTBE- spent granular activated carbon

    EPA Science Inventory

    Chemical oxidation is a developing technology used to regenerate contaminant-spent GAC. Chemical regeneration of GAC represents a viable option to thermal regeneration methods that are energy intensive resulting in significant consumption of fossil fuels and production of greenho...

  14. ACTIVE MEDIA: Nonlinear thermally induced distortions of a laser beam in a cryogenic disk amplifier

    NASA Astrophysics Data System (ADS)

    Vyatkin, A. G.; Khazanov, Efim A.

    2009-09-01

    Taking into account the temperature dependences of the heat conductivity, the refractive index, and the thermal expansion coefficient, we calculated the temperature, elastic stresses, a thermally induced lens and depolarisation of a beam in a cryogenic disk amplifier (an Yb:YAG disk placed between a copper cylinder and a sapphire disk cooled by liquid nitrogen). When the active element (the thickness is 0.6 mm, the orientation is [001], the atomic concentration of Yb is 10%) is pumped by radiation from a diode laser (the beam diameter is 6 mm), the temperature does not exceed 140 K for the heat release power of 100 W. In this case, elastic stresses in the active element are six times lower than the maximum permissible value. The focal distance of the thermally induced lens is 5.5 m and the depolarisation rate is 0.038% per two passes through the active element. Although the heat conductivity of the active element rapidly decreases with temperature, the thermal load can be increased by 1.5-2 times when the dimensions of the active element remain constant.

  15. Activity and stability of the oxygen evolution reaction on electrodeposited Ru and its thermal oxides

    NASA Astrophysics Data System (ADS)

    Kim, Jin Yeong; Choi, Jihui; Kim, Ho Young; Hwang, Eunkyoung; Kim, Hyoung-Juhn; Ahn, Sang Hyun; Kim, Soo-Kil

    2015-12-01

    The activity and stability of Ru metal and its thermal oxide films for the oxygen evolution reaction (OER) were investigated. The metallic Ru films were prepared by electrodeposition on a Ti substrate and then thermally oxidized at various temperatures under atmospheric conditions. During long-term operation of the OER with cyclic voltammetry (CV) in H2SO4 electrolyte, changes in the properties of the Ru and its thermal oxides were monitored in terms of their morphology, crystal structure, and electronic structure. In the initial stages of the OER, all of the Ru thermal oxide films underwent an activation process that was related to the continuous removal of low-activity Ru oxides from the surface. With further cycling, the OER activity decreased. The rate of decrease was different for each Ru film and was related to the annealing temperatures. Monitoring of material properties indicates that the amount of stable anhydrous RuO2 is important for OER stability because it prevents both the severe dissolution of metallic Ru beneath the oxide surface and the formation of a less active hydrous RuO2 at the surface.

  16. Development of high flux thermal neutron generator for neutron activation analysis

    NASA Astrophysics Data System (ADS)

    Vainionpaa, Jaakko H.; Chen, Allan X.; Piestrup, Melvin A.; Gary, Charles K.; Jones, Glenn; Pantell, Richard H.

    2015-05-01

    The new model DD110MB neutron generator from Adelphi Technology produces thermal (<0.5 eV) neutron flux that is normally achieved in a nuclear reactor or larger accelerator based systems. Thermal neutron fluxes of 3-5 · 107 n/cm2/s are measured. This flux is achieved using four ion beams arranged concentrically around a target chamber containing a compact moderator with a central sample cylinder. Fast neutron yield of ∼2 · 1010 n/s is created at the titanium surface of the target chamber. The thickness and material of the moderator is selected to maximize the thermal neutron flux at the center. The 2.5 MeV neutrons are quickly thermalized to energies below 0.5 eV and concentrated at the sample cylinder. The maximum flux of thermal neutrons at the target is achieved when approximately half of the neutrons at the sample area are thermalized. In this paper we present simulation results used to characterize performance of the neutron generator. The neutron flux can be used for neutron activation analysis (NAA) prompt gamma neutron activation analysis (PGNAA) for determining the concentrations of elements in many materials. Another envisioned use of the generator is production of radioactive isotopes. DD110MB is small enough for modest-sized laboratories and universities. Compared to nuclear reactors the DD110MB produces comparable thermal flux but provides reduced administrative and safety requirements and it can be run in pulsed mode, which is beneficial in many neutron activation techniques.

  17. Draft position paper on knowledge management in space activities

    NASA Technical Reports Server (NTRS)

    Holm, Jeanne; Moura, Denis

    2003-01-01

    As other fields of industry, space activities are facing the challenge of Knowledge Management and the International Academy of Astronautics decided to settle in 2002 a Study Group to analyse the problem and issue general guidelines. This communication presents the draft position paper of this group in view to be discussed during the 2003 IAF Congress.

  18. Moodog: Tracking Student Activity in Online Course Management Systems

    ERIC Educational Resources Information Center

    Zhang, Hangjin; Almeroth, Kevin

    2010-01-01

    Many universities are currently using Course Management Systems (CMSes) to conduct online learning, for example, by distributing course materials or submitting homework assignments. However, most CMSes do not include comprehensive activity tracking and analysis capabilities. This paper describes a method to track students' online learning…

  19. Management of Hypertension: Adapting New Guidelines for Active Patients.

    ERIC Educational Resources Information Center

    Tanji, Jeffrey L.; Batt, Mark E.

    1995-01-01

    Discusses recent guidelines on hypertension from the National Heart, Lung, and Blood Institute and details the latest management protocols for patients with high blood pressure. The article helps physicians interpret the guidelines for treating active patients, highlighting diagnosis, step care revision, pharmacology, and sports participation…

  20. Building automation: Photovoltaic assisted thermal comfort management system for energy saving

    NASA Astrophysics Data System (ADS)

    Reyasudin Basir Khan, M.; Jidin, Razali; Pasupuleti, Jagadeesh; Azwa Shaaya, Sharifah

    2013-06-01

    Building automation plays an important key role in the means to reduce building energy consumption and to provide comfort for building occupants. It is often that air conditioning system operating features ignored in building automation which can result in thermal discomfort among building occupants. Most automation system for building is expensive and incurs high maintenance cost. Such system also does not support electricity demand side management system such as load shifting. This paper discusses on centralized monitoring system for room temperature and photovoltaic (PV) output for feasibility study of PV assisted air conditioning system in small office buildings. The architecture of the system consists of PV modules and sensor nodes located at each room. Wireless sensor network technology (WSN) been used for data transmission. The data from temperature sensors and PV modules transmitted to the host personal computer (PC) wirelessly using Zigbee modules. Microcontroller based USB data acquisition device used to receive data from sensor nodes and displays the data on PC.

  1. Metal foam heat exchangers for thermal management of fuel cell systems

    NASA Astrophysics Data System (ADS)

    Odabaee, M.; Hooman, K.

    2012-05-01

    The present study explores the possibility of using metal foams for thermal management of fuel cells so that air-cooled fuel cell stacks can be commercialized as replacements for currently-available water-cooled counterparts. Experimental studies have been conducted to examine the heat transfer enhancement from a thin metal foam layer sandwiched between two bipolar plates of a cell. To do this, effects of the key parameters including the free stream velocity and characteristics of metal foam such as porosity, permeability, and form drag coefficient on heat and fluid flow are investigated. The improvements as a result of the application of metal foam layers on fuel cell systems efficiency have been analyzed and discussed. Non-optimized results have shown that to remove the same amount of generated heat, the air-cooled fuel cell systems using aluminum foams require half of the pumping power compared to water-cooled fuel cell systems.

  2. Numerical Study of Flow Augmented Thermal Management for Entry and Re-Entry Environments

    NASA Technical Reports Server (NTRS)

    Cheng, Gary C.; Neroorkar, Kshitij D.; Chen, Yen-Sen; Wang, Ten-See; Daso, Endwell O.

    2007-01-01

    The use of a flow augmented thermal management system for entry and re-entr environments is one method for reducing heat and drag loads. This concept relies on jet penetration from supersonic and hypersonic counterflowing jets that could significantly weaken and disperse the shock-wave system of the spacecraft flow field. The objective of this research effort is to conduct parametric studies of the supersonic flow over a 2.6% scale model of the Apollo capsule, with and without the counterflowing jet, using time-accurate and steady-state computational fluid dynamics simulations. The numerical studies, including different freestream Mach number angle of attack counterflowing jet mass flow rate, and nozzle configurations, were performed to examine their effect on the drag and beat loads and to explore the counternowing jet condition. The numerical results were compared with the test data obtained from transonic blow-down wind-tunnel experiments conducted independently at NASA MSFC.

  3. Modelling of transient two-phase heat transfer for spacecraft thermal management

    NASA Technical Reports Server (NTRS)

    Shyy, W.

    1994-01-01

    A computational method for predicting the two-phase transient fluid flow and heat transfer characteristics within a reservoir of the capillary-pumped-loop, intended to be used for spacecraft thermal management, has been developed. The model is based on the enthalpy formulation in an axisymmetric configuration. The reservoir operates under a constant thermodynamic pressure by allowing mass exchange between the reservoir and the outside loop. Both 1 g and 0 g environments have been considered to assess the effects of gravity on the reservoir performance. Depending on the gravity level, the power input and the reservoir orientation, three different convection modes have been identified, namely, the thermocapillary mode, the buoyancy mode, and the rapid-expansion mode (caused by interface movement). The impact of these modes on the performance of the reservoir and the associated physical phenomena have been discussed.

  4. Development of relative thermal stress index (RTSI) for Monitoring and Management of Dry Deciduous Ecosystem

    NASA Astrophysics Data System (ADS)

    Gupta, R. K.; Vijayan, D.

    Gir wildlife sanctuary located between 20 r 57 to 21 r 20 N and 70 r 28 to 71 r 13 E is the last home of Asiatic lions Its biodiversity comprises of 450 recorded flowering plant species 32 species of mammals 26 species of reptiles about 300 species of birds and more than 2000 species of insects As per 1995 census it has 304 lions and 268 leopards The movement of wildlife to thermally comfortable zones to reduce stress conditions forces the changes in management plan with reference to change in localized water demand This necessitates the use of space based thermal data available from AVHRR MODIS etc to monitor temperature of Gir-ecosystem for meso-scale level operational utility As the time scale of the variability of NDVI parameter is much higher than that for lower boundary temperature LBT the dense patch in riverine forest having highest NDVI value would not experience change in its vigour with the change in the season NDVI value of such patch would be near invariant over the year and temperature of this pixel could serve as reference temperature for developing the concept of relative thermal stress index RTSI which is defined as RTSI T p -T r T max -T r wherein T r T max and T p refer to LBT over the maximum NDVI reference point maximum LBT observed in the Gir ecosystem and the temperature of the pixel in the image respectively RTSI images were computed from AVHRR images for post-monsoon leaf-shedded and summer seasons Scatter plot between RTSI and NDVI for summer seasons

  5. Managing Risk for Thermal Vacuum Testing of the International Space Station Radiators

    NASA Technical Reports Server (NTRS)

    Carek, Jerry A.; Beach, Duane E.; Remp, Kerry L.

    2000-01-01

    The International Space Station (ISS) is designed with large deployable radiator panels that are used to reject waste heat from the habitation modules. Qualification testing of the Heat Rejection System (HRS) radiators was performed using qualification hardware only. As a result of those tests, over 30 design changes were made to the actual flight hardware. Consequently, a system level test of the flight hardware was needed to validate its performance in the final configuration. A full thermal vacuum test was performed on the flight hardware in order to demonstrate its ability to deploy on-orbit. Since there is an increased level of risk associated with testing flight hardware, because of cost and schedule limitations, special risk mitigation procedures were developed and implemented for the test program, This paper introduces the Continuous Risk Management process that was utilized for the ISS HRS test program. Testing was performed in the Space Power Facility at the NASA Glenn Research Center, Plum Brook Station located in Sandusky, Ohio. The radiator system was installed in the 100-foot diameter by 122-foot tall vacuum chamber on a special deployment track. Radiator deployments were performed at several thermal conditions similar to those expected on-orbit using both the primary deployment mechanism and the back-up deployment mechanism. The tests were highly successful and were completed without incident.

  6. An experimental study of lithium ion battery thermal management using flexible hydrogel films

    NASA Astrophysics Data System (ADS)

    Zhao, Rui; Zhang, Sijie; Gu, Junjie; Liu, Jie; Carkner, Steve; Lanoue, Eric

    2014-06-01

    Many portable devices such as soldier carrying devices are powered by low-weight but high-capacity lithium ion (Li-ion) batteries. An effective battery thermal management (BTM) system is required to keep the batteries operating within a desirable temperature range with minimal variations, and thus to guarantee their high efficiency, long lifetime and great safety. However, the rigorous constraints imposed by the budgets in weight and volume for this specific application eliminate the possible consideration of many existing classical cooling approaches and make the development of BTM system very challenging in this field. In this paper, a flexible hydrogel-based BTM system is developed to address this challenge. The proposed BTM system is based on cost-effective sodium polyacrylate and can be arbitrarily shaped and conveniently packed to accommodate any Li-ion stacks. This BTM system is tested through a series of high-intensity discharge and abnormal heat release processes, and its performance is compared with three classical BTM systems. The test results demonstrate that the proposed low-cost, space-saving, and contour-adaptable BTM system is a very economic and efficient approach in handling the thermal surge of Li-ion batteries.

  7. Relation between Thermal and Magnetic Properties of Active Regions as a Probe of Coronal Heating Mechanisms

    NASA Astrophysics Data System (ADS)

    Yashiro, Seiji; Shibata, Kazunari

    2001-03-01

    We study the relation between thermal and magnetic properties of active regions in the corona observed with the soft X-ray telescope aboard Yohkoh. We derive the mean temperature and pressure of 64 mature active regions using the filter ratio technique, and examine the relationship of region size with temperature and pressure. We find that the temperature T of active regions increases with increasing region size L as T~L0.28, while the pressure P slightly decreases with the region size as P~L-0.16. We confirm the scaling law T~(PL)1/3 for mature active regions found by R. Rosner, W. H. Tucker, & G. S. Vaiana. We examined the magnetic properties of active regions by analyzing 31 active regions observed with the Solar and Heliospheric Observatory/Michelson Doppler Imager and find the following empirical scaling law between thermal and magnetic properties,Uth~Φ1.33,P~B0.78,where Uth, Φ, and B are the total thermal energy content, total magnetic flux, and average magnetic flux density of active regions, respectively. The former is consistent with the results of L. Golub et al., but the latter is not. Implications of our findings for coronal heating mechanisms are discussed.

  8. Thermally Activated Delayed Fluorescence in Polymers: A New Route toward Highly Efficient Solution Processable OLEDs.

    PubMed

    Nikolaenko, Andrey E; Cass, Michael; Bourcet, Florence; Mohamad, David; Roberts, Matthew

    2015-11-25

    Efficient intermonomer thermally activated delayed fluorescence is demonstrated for the first time, opening a new route to achieving high-efficiency solution processable polymer light-emitting device materials. External quantum efficiency (EQE) of up to 10% is achieved in a simple fully solution-processed device structure, and routes for further EQE improvement identified. PMID:26457683

  9. Design strategy for 25% external quantum efficiency in green and blue thermally activated delayed fluorescent devices.

    PubMed

    Lee, Dong Ryun; Kim, Mounggon; Jeon, Sang Kyu; Hwang, Seok-Ho; Lee, Chil Won; Lee, Jun Yeob

    2015-10-21

    Carbazole- and triazine-derived thermally activated delayed fluorescent (TADF) emitters, with three donor units and an even distribution of the highest occupied molecular orbital, achieve high external quantum efficiencies of above 25% in blue and green TADF devices. PMID:26308481

  10. Benzofurocarbazole and benzothienocarbazole as donors for improved quantum efficiency in blue thermally activated delayed fluorescent devices.

    PubMed

    Lee, Dong Ryun; Hwang, Seok-Ho; Jeon, Sang Kyu; Lee, Chil Won; Lee, Jun Yeob

    2015-05-11

    Benzofurocarbazole and benzothienocarbazole were used as electron donors of thermally activated delayed fluorescence (TADF) emitters and the performances of the TADF devices were examined. The benzofurocarbazole and benzothienocarbazole donor moieties were better than carbazole as the electron donors of the TADF emitters. PMID:25869643

  11. Active mode calibration of the combined thermal epithermal neutron (CTEN) system

    SciTech Connect

    Veilleux, J. M.

    2001-01-01

    The Combined Thermal Epithermal Neutron (CTEN) system was developed by the Los Alamos National Laboratory to perform active and passive neutron interrogation of waste. The higher energy epithermal neutrons are able to penetrate further into the matrix and active material, thus reducing matrix attenuation and self-shielding effects compared to a thermal neutron pulse alone. The developmental unit was installed in 2001 at the Los Alamos Non-Destructive Assay (NDA) facility to characterize waste for the TRU Waste Characterization Project (TWCP). This paper summarizes the active mode certification results. National Institute of Standards and Technology (NIST) traceable standards were used to determine the system response as a function of mass. Finally, NIST-traceable verification standards were used to verify the calibration in the range 30 milligrams to 25 g of weapons grade plutonium although self-shielding limits the upper active interrogation to 10 g.

  12. An integrated model of the Space Station Freedom active thermal control system

    NASA Technical Reports Server (NTRS)

    Tandler, John J.; Bilardo, Vincent J., Jr.

    1989-01-01

    A flexible, generic model of the Space Station Freedom active thermal control system has been developed which is designed to analyze dynamic interactions of the major subsystems of the ATCS. Models are described for the components of the central thermal bus, the radiator external thermal environment, and the internal thermal control system. Two programs are described which facilitate the development of the integrated ATCS model. The first, SIMRAD, simplifies an external thermal environment model given a desired level of accuracy in integrated model performance. The model reduction technique is shown to reduce model execution time significantly while maintaining the desired accuracy. The second, GENFLU, generates SINDA/FLUINT input code for the evaporator and load interface models and automates the integration of load submodels. The component submodels and integration techniques were used to create an integrated model of the thermal control system for an early assembly flight configuration. The results demonstrate the utility of the integrated model in studying dynamic interactions of the ATCS subsystems.

  13. A novel active suppression technology against thermal drift for ultra-precision spherical capacitive sensors

    NASA Astrophysics Data System (ADS)

    Cui, Junning; Lu, Yesheng; Sun, Tao; Ou, Yaodong

    2015-02-01

    In order to solve the problem of thermal drift and further improve the performance for sensors with extreme demand for precision, based on analysis of shortcomings of existing compensation methods and characteristics of thermal drift, a novel active suppression technology against thermal drift is proposed. Considering the change of properties of reference elements in sensors caused by temperature variation is the most major factor that introduces thermal drift error, a special thermal structure is designed to provide a small environmental chamber with sub-structure design of high performance heat isolation, heat conduction and homogenization of temperature, and the temperature in the environmental chamber is controlled with high precision based on bilateral temperature adjusting with thermo electronic cooler (TEC) devices, and a compound control algorithm of Bang-Bang and anti-windup PID. Experimental results with an ultra-precision spherical capacitive sensor show thermal drift error is significantly eliminated and the precision of the sensor can reach the level of several resolutions.

  14. Moderate Thermal Stress Causes Active and Immediate Expulsion of Photosynthetically Damaged Zooxanthellae (Symbiodinium) from Corals

    PubMed Central

    Fujise, Lisa; Yamashita, Hiroshi; Suzuki, Go; Sasaki, Kengo; Liao, Lawrence M.; Koike, Kazuhiko

    2014-01-01

    The foundation of coral reef biology is the symbiosis between corals and zooxanthellae (dinoflagellate genus Symbiodinium). Recently, coral bleaching, which often results in mass mortality of corals and the collapse of coral reef ecosystems, has become an important issue around the world as coral reefs decrease in number year after year. To understand the mechanisms underlying coral bleaching, we maintained two species of scleractinian corals (Acroporidae) in aquaria under non-thermal stress (27°C) and moderate thermal stress conditions (30°C), and we compared the numbers and conditions of the expelled Symbiodinium from these corals. Under non-thermal stress conditions corals actively expel a degraded form of Symbiodinium, which are thought to be digested by their host coral. This response was also observed at 30°C. However, while the expulsion rates of Symbiodinium cells remained constant, the proportion of degraded cells significantly increased at 30°C. This result indicates that corals more actively digest and expel damaged Symbiodinium under thermal stress conditions, likely as a mechanism for coping with environmental change. However, the increase in digested Symbiodinium expulsion under thermal stress may not fully keep up with accumulation of the damaged cells. There are more photosynthetically damaged Symbiodinium upon prolonged exposure to thermal stress, and corals release them without digestion to prevent their accumulation. This response may be an adaptive strategy to moderate stress to ensure survival, but the accumulation of damaged Symbiodinium, which causes subsequent coral deterioration, may occur when the response cannot cope with the magnitude or duration of environmental stress, and this might be a possible mechanism underlying coral bleaching during prolonged moderate thermal stress. PMID:25493938

  15. Characteristics of Trailer Thermal Environment during Commercial Swine Transport Managed under U.S. Industry Guidelines.

    PubMed

    Xiong, Yijie; Green, Angela; Gates, Richard S

    2015-01-01

    Transport is a critical factor in modern pork production and can seriously affect swine welfare. While previous research has explored thermal conditions during transport, the impact of extreme weather conditions on the trailer thermal environment under industry practices has not been well documented; and the critical factors impacting microclimate are not well understood. To assess the trailer microclimate during transport events, an instrumentation system was designed and installed at the central ceiling level, pig level and floor-level in each of six zones inside a commercial swine trailer. Transport environmental data from 34 monitoring trips (approximately 1-4 h in duration each) were collected from May, 2012, to February, 2013, with trailer management corresponding to the National Pork Board Transport Quality Assurance (TQA) guidelines in 31 of these trips. According to the TQA guidelines, for outdoor temperature ranging from 5 °C (40 °F) to 27 °C (80 °F), acceptable thermal conditions were observed based on the criteria that no more than 10% of the trip duration was above 35 °C (95 °F) or below 0 °C (32 °F). Recommended bedding, boarding and water application were sufficient in this range. Measurements support relaxing boarding guidelines for moderate outdoor conditions, as this did not result in less desirable conditions. Pigs experienced extended undesirable thermal conditions for outdoor temperatures above 27 °C (80 °F) or below 5 °C (40 °F), meriting a recommendation for further assessment of bedding, boarding and water application guidelines for extreme outdoor temperatures. An Emergency Livestock Weather Safety Index (LWSI) condition was observed inside the trailer when outdoor temperature exceeded 10 °C (50 °F); although the validity of LWSI to indicate heat stress for pigs during transport is not well established. Extreme pig surface temperatures in the rear and middle zones of the trailer were more frequently experienced than in the

  16. Micro/Nano-Scale Phase Change Systems for Thermal Management and Solar Energy Conversion Applications

    NASA Astrophysics Data System (ADS)

    Coso, Dusan

    The first part of the dissertation presents a study that implements micro and nano scale engineered surfaces for enhancement of evaporation and boiling phase change heat transfer in both capillary wick structures and pool boiling systems. Capillary wicking surfaces are integral components of heat pipes and vapor chamber thermal spreaders often used for thermal management of microelectronic devices. In addition, pool boiling systems can be encountered in immersion cooling systems which are becoming more commonly investigated for thermal management applications of microelectronic devices and even data centers. The latent heat associated with the change of state from liquid to vapor, and the small temperature differences required to drive this process yield great heat transfer characteristics. Additionally, since no external energy is required to drive the phase change process, these systems are great for portable devices and favorable for reduction of cost and energy consumption over alternate thermal management technologies. Most state of the art capillary wicks used in these devices are typically constructed from sintered copper media. These porous structures yield high surface areas of thin liquid film where evaporation occurs, thus promoting phase change heat transfer. However, thermal interfaces at particle point contacts formed during the sintering process and complex liquid/vapor flow within these wick structures yield high thermal and liquid flow resistances and limit the maximum heat flux they can dissipate. In capillary wicks the maximum heat flux is typically governed by the capillary or boiling limits and engineering surfaces that delay these limitations and yield structures with large surface areas of thin liquid film where phase change heat transfer is promoted is highly desired. In this study, biporous media consisting of microscale pin fins separated by microchannels are examined as candidate structures for the evaporator wick of a vapor chamber heat

  17. Novel polymer composite having diamond particles and boron nitride platelets for thermal management of electric vehicle motors

    NASA Astrophysics Data System (ADS)

    Nakajima, Anri; Shoji, Atsushi; Yonemori, Kei; Seo, Nobuhide

    2016-02-01

    Thermal conductivities of silicone matrix polymers including fillers of diamond particles and/or hexagonal boron nitride (h-BN) platelets were systematically investigated in an attempt to find a thermal interface material (TIM) having high isotropic thermal conductivity and high electrical insulating ability to enable efficient heat dissipation from the motor coil ends of electric vehicles. The TIM with mixed fillers of diamond particles and h-BN platelets had a maximum thermal conductivity of 6.1 W m-1 K-1 that was almost isotropic. This is the highest value among the thermal conductivities of TIMs with silicone matrix polymer reported to date. The mechanism behind the thermal conductivity of the TIMs was also examined from the viewpoint of the change in the number of thermally conductive networks and/or a decrease in the thermal resistivity of junctions of neighboring diamond particles through the incorporation of h-BN platelets. The TIMs developed in this study will make it possible to manage the heat of electric motors and will help to popularize electric vehicles.

  18. SECONDARY WASTE MANAGEMENT STRATEGY FOR EARLY LOW ACTIVITY WASTE TREATMENT

    SciTech Connect

    TW, CRAWFORD

    2008-07-17

    This study evaluates parameters relevant to River Protection Project secondary waste streams generated during Early Low Activity Waste operations and recommends a strategy for secondary waste management that considers groundwater impact, cost, and programmatic risk. The recommended strategy for managing River Protection Project secondary waste is focused on improvements in the Effiuent Treatment Facility. Baseline plans to build a Solidification Treatment Unit adjacent to Effluent Treatment Facility should be enhanced to improve solid waste performance and mitigate corrosion of tanks and piping supporting the Effiuent Treatment Facility evaporator. This approach provides a life-cycle benefit to solid waste performance and reduction of groundwater contaminants.

  19. Integrated thermal and energy management of plug-in hybrid electric vehicles

    NASA Astrophysics Data System (ADS)

    Shams-Zahraei, Mojtaba; Kouzani, Abbas Z.; Kutter, Steffen; Bäker, Bernard

    2012-10-01

    In plug-in hybrid electric vehicles (PHEVs), the engine temperature declines due to reduced engine load and extended engine off period. It is proven that the engine efficiency and emissions depend on the engine temperature. Also, temperature influences the vehicle air-conditioner and the cabin heater loads. Particularly, while the engine is cold, the power demand of the cabin heater needs to be provided by the batteries instead of the waste heat of engine coolant. The existing energy management strategies (EMS) of PHEVs focus on the improvement of fuel efficiency based on hot engine characteristics neglecting the effect of temperature on the engine performance and the vehicle power demand. This paper presents a new EMS incorporating an engine thermal management method which derives the global optimal battery charge depletion trajectories. A dynamic programming-based algorithm is developed to enforce the charge depletion boundaries, while optimizing a fuel consumption cost function by controlling the engine power. The optimal control problem formulates the cost function based on two state variables: battery charge and engine internal temperature. Simulation results demonstrate that temperature and the cabin heater/air-conditioner power demand can significantly influence the optimal solution for the EMS, and accordingly fuel efficiency and emissions of PHEVs.

  20. From Ultrafine Thiolate-Capped Copper Nanoclusters toward Copper Sulfide Nanodiscs: A Thermally Activated Evolution Route

    SciTech Connect

    Mott, Derrick; Yin, Jun; Engelhard, Mark H.; Loukrakpam, Rameshwori; Chang, Paul; Miller, George; Bae, In-Tae; Das, N. C.; Wang, Chong M.; Luo, Jin; Zhong, Chuan-Jian

    2010-01-12

    In this report we show that the size, shape, and composition of pre-synthesized metal nanoparticles can be engineered through exploiting concurrent interparticle coalescence and interfacial copper-thiolate cleavage under a thermally-activated evolution process. This concept is demonstrated by thermally-activated processing of ultrafine (~0.5 nm) copper nanoparticles encapsulated with thiolate monolayer (Cun(SR)m) toward copper sulfide nanodiscs with controllable sizes and shapes. It involved a thermally-activated coalescence of Cun(SR)m nanoclusters accompanied by interfacial Cu-S cleavage towards the formation of Cu2S nanocrystals with well-defined nanodisc shapes with an average diameter and thickness ranging from 10.7 ±1.4 nm and 5.5 ±0.5 nm (aspect ratio ~2) to 31.2 ±4.3 nm and 3.9 ±0.4 nm (aspect ratio ~7) depending on the thermal processing parameters. These nanodiscs are stable and display remarkable ordering upon self-assembly. The abilities to create the ultrafine copper nanoclusters and to enable them to undergo a thermally-activated coalescence and a concurrent Cu-S bond cleavage toward the formation of Cu2S nanodiscs is entirely new. The viability of fine tuning the size and shape of the Cu2S nanocrystals by controlling the relative binding strength of thiolates, the C-S cleavage reactivity, and the interparticle coalescence activity, and their potential applications in electronic, sensing and photochemical devices are also discussed.

  1. A theoretical and computational study of lithium-ion battery thermal management for electric vehicles using heat pipes

    NASA Astrophysics Data System (ADS)

    Greco, Angelo; Cao, Dongpu; Jiang, Xi; Yang, Hong

    2014-07-01

    A simplified one-dimensional transient computational model of a prismatic lithium-ion battery cell is developed using thermal circuit approach in conjunction with the thermal model of the heat pipe. The proposed model is compared to an analytical solution based on variable separation as well as three-dimensional (3D) computational fluid dynamics (CFD) simulations. The three approaches, i.e. the 1D computational model, analytical solution, and 3D CFD simulations, yielded nearly identical results for the thermal behaviours. Therefore the 1D model is considered to be sufficient to predict the temperature distribution of lithium-ion battery thermal management using heat pipes. Moreover, a maximum temperature of 27.6 °C was predicted for the design of the heat pipe setup in a distributed configuration, while a maximum temperature of 51.5 °C was predicted when forced convection was applied to the same configuration. The higher surface contact of the heat pipes allows a better cooling management compared to forced convection cooling. Accordingly, heat pipes can be used to achieve effective thermal management of a battery pack with confined surface areas.

  2. Thermal analysis on grad-doped active-mirror Yb:YAG ceramic lasers

    NASA Astrophysics Data System (ADS)

    Cheng, Xiaojin; Wang, Jianlei; Jiang, Benxue

    2015-11-01

    Heat conduction, temperature distribution, thermal stress, and thermally induced refractive index of a diode-pumped active-mirror grad-doped Yb:YAG ceramic laser are analyzed and compared to a uniform-doped Yb:YAG ceramic laser. It is found that a rationally designed grad-doped Yb:YAG ceramic has a smaller temperature gradient than a uniform-doped Yb:YAG ceramic with the same absorption pump power, which results in higher output energy in the grad-doped Yb:YAG ceramic laser.

  3. Measurements of Non-thermal Line Widths in Solar Active Regions

    NASA Astrophysics Data System (ADS)

    Brooks, David H.; Warren, Harry P.

    2016-03-01

    Spectral line widths are often observed to be larger than can be accounted for by thermal and instrumental broadening alone. This excess broadening is a key observational constraint for both nanoflare and wave dissipation models of coronal heating. Here we present a survey of non-thermal velocities measured in the high temperature loops (1-4 MK) often found in the cores of solar active regions. This survey of Hinode Extreme Ultraviolet Imaging Spectrometer (EIS) observations covers 15 non-flaring active regions that span a wide range of solar conditions. We find relatively small non-thermal velocities, with a mean value of 17.6 ± 5.3 km s-1, and no significant trend with temperature or active region magnetic flux. These measurements appear to be inconsistent with those expected from reconnection jets in the corona, chromospheric evaporation induced by coronal nanoflares, and Alfvén wave turbulence models. Furthermore, because the observed non-thermal widths are generally small, such measurements are difficult and susceptible to systematic effects.

  4. Thermally treated wine retains vasodilatory activity in rat and guinea pig aorta.

    PubMed

    Mudnić, Ivana; Budimir, Danijela; Jajić, Ivan; Boban, Nataša; Sutlović, Davorka; Jerončić, Ana; Boban, Mladen

    2011-06-01

    In contrast to the intact wine, cardiovascular effects of the thermally treated wine have not been studied, despite widespread habits of cooking with wine and consumption of mulled wine. Vasodilatory effects of the red wine heated at 75 and 125°C were examined in the isolated rat and guinea pig aorta and compared with the intact and wine dealcoholized without thermal stress. Samples were analyzed for their phenolic content, antioxidant capacity, resveratrol and ethanol contents. Heating-induced degradation of individual phenolic fraction was observed only in the samples treated at 125°C, although total phenolic concentration and related antioxidant activity increased in the thermally treated samples due to the reduction in their volume. All wine samples regardless of treatment caused similar maximal relaxation in both species, but the response was stronger in aortas from guinea pigs. At the lowest concentrations up to 1‰, dealcoholized wine produced vasodilation greater than that produced by intact wine and wines treated at 75 and 125°C, which showed similar vasodilating activity at all concentrations. Our results indicate that wine thermally treated under heating conditions applicable to the preparation of a mulled wine and cooking with wine largely retains vasodilatory activity in vitro despite significant heat-induced changes in its composition. PMID:21423027

  5. Optical analysis and thermal management of 2-cell strings linear concentrating photovoltaic system

    NASA Astrophysics Data System (ADS)

    Reddy, K. S.; Kamnapure, Nikhilesh R.

    2015-09-01

    This paper presents the optical and thermal analyses for a linear concentrating photovoltaic/thermal collector under different operating conditions. Linear concentrating photovoltaic system (CPV) consists of a highly reflective mirror, a receiver and semi-dual axis tracking mechanism. The CPV receiver embodies two strings of triple-junction cells (100 cells in each string) adhered to a mild steel circular tube mounted at the focal length of trough. This system provides 560 W of electricity and 1580 W of heat which needs to be dissipated by active cooling. The Al2O3/Water nanofluid is used as heat transfer fluid (HTF) flowing through circular receiver for CPV cells cooling. Optical analysis of linear CPV system with 3.35 m2 aperture and geometric concentration ratio (CR) of 35 is carried out using Advanced System Analysis Program (ASAP) an optical simulation tool. Non-uniform intensity distribution model of solar disk is used to model the sun in ASAP. The impact of random errors including slope error (σslope), tracking error (σtrack) and apparent change in sun's width (σsun) on optical performance of collector is shown. The result from the optical simulations shows the optical efficiency (ηo) of 88.32% for 2-cell string CPV concentrator. Thermal analysis of CPV receiver is carried out with conjugate heat transfer modeling in ANSYS FLUENT-14. Numerical simulations of Al2O3/Water nanofluid turbulent forced convection are performed for various parameters such as nanoparticle volume fraction (φ), Reynolds number (Re). The addition of the nanoparticle in water enhances the heat transfer in the ranges of 3.28% - 35.6% for φ = 1% - 6%. Numerical results are compared with literature data which shows the reasonable agreement.

  6. Thermally activated switching of perpendicular magnet by spin-orbit spin torque

    SciTech Connect

    Lee, Ki-Seung; Lee, Seo-Won; Min, Byoung-Chul; Lee, Kyung-Jin

    2014-02-17

    We theoretically investigate the threshold current for thermally activated switching of a perpendicular magnet by spin-orbit spin torque. Based on the Fokker-Planck equation, we obtain an analytic expression of the switching current, in agreement with numerical result. We find that thermal energy barrier exhibits a quasi-linear dependence on the current, resulting in an almost linear dependence of switching current on the log-scaled current pulse-width even below 10 ns. This is in stark contrast to standard spin torque switching, where thermal energy barrier has a quadratic dependence on the current and the switching current rapidly increases at short pulses. Our results will serve as a guideline to design and interpret switching experiments based on spin-orbit spin torque.

  7. Thermal hydrolysis of waste activated sludge at Hengelo Wastewater Treatment Plant, the Netherlands.

    PubMed

    Oosterhuis, Mathijs; Ringoot, Davy; Hendriks, Alexander; Roeleveld, Paul

    2014-01-01

    The thermal hydrolysis process (THP) is a sludge treatment technique which affects anaerobic biodegradability, viscosity and dewaterability of waste activated sludge (WAS). In 2011 a THP-pilot plant was operated, connected to laboratory-scale digesters, at the water board Regge en Dinkel and in cooperation with Cambi A.S. and MWH Global. Thermal hydrolysis of WAS resulted in a 62% greater volatile solids (VS) reduction compared to non-hydrolysed sludge. Furthermore, the pilot digesters could be operated at a 2.3 times higher solids loading rate compared to conventional sludge digesters. By application of thermal sludge hydrolysis, the overall efficiency of the sludge treatment process can be improved. PMID:25026572

  8. Thermally activated phase slips in superfluid spin transport in magnetic wires

    NASA Astrophysics Data System (ADS)

    Kim, Se Kwon; Takei, So; Tserkovnyak, Yaroslav

    2016-01-01

    We theoretically study thermally activated phase slips in superfluid spin transport in easy-plane magnetic wires within the stochastic Landau-Lifshitz-Gilbert phenomenology, which runs parallel to the Langer-Ambegaokar-McCumber-Halperin theory for thermal resistances in superconducting wires. To that end, we start by obtaining the exact solutions for free-energy minima and saddle points. We provide an analytical expression for the phase-slip rate in the zero spin-current limit, which involves a detailed analysis of spin fluctuations at the extrema of the free energy. An experimental setup for a magnetoelectric circuit is proposed, in which thermal phase slips can be inferred by measuring nonlocal magnetoresistance.

  9. Optically Detected Magnetic Resonance and Thermal Activation Spectroscopy Study of Organic Semiconductors

    SciTech Connect

    Chang-Hwan Kim

    2003-12-12

    Organic electronic materials are a new class of emerging materials. Organic light emitting devices (OLEDs) are the most promising candidates for future flat panel display technologies. The photophysical characterization is the basic research step one must follow to understand this new class of materials and devices. The light emission properties are closely related to the transport properties of these materials. The objective of this dissertation is to probe the relation between transport and photophysical properties of organic semiconductors. The transport characteristics were evaluated by using thermally stimulated current and thermally stimulated luminescence techniques. The photoluminescence detected magnetic resonance and photoluminescence quantum yield studies provide valuable photophysical information on this class of materials. OLEDs are already in the market. However, detailed studies on the degradation mechanisms are still lacking. Since both optically detected magnetic resonance and thermal activation spectroscopy probe long-lived defect-related states in organic semiconductors, the combined study generates new insight on the OLED operation and degradation mechanisms.

  10. An active thermography approach for thermal and electrical characterization of thermoelectric materials

    NASA Astrophysics Data System (ADS)

    Streza, M.; Longuemart, S.; Guilmeau, E.; Strzalkowski, K.; Touati, K.; Depriester, M.; Maignan, A.; Sahraoui, A. Hadj

    2016-07-01

    The enhancement of figure of merit (ZT) of thermoelectrics is becoming extremely important for an efficient conversion of thermal energy into electrical energy. In this respect, reliable measurements of thermal and electrical parameters are of paramount importance in order to characterize thermoelectric materials in terms of their efficiency. In this work, a combined theoretical-experimental active thermography approach is presented. The method consists of selecting the right sequential interdependence between the excitation frequency and the sampling rate of the infrared camera, by computing a temporal Fourier analysis of each pixel of the recorded IR image. The method is validated by using a reference sample which is then applied to a recent synthesized titanium trisulphide thermoelectric material (TiS3). By combining AC and steady-state experiments, one can obtain information on both thermal and electrical parameters of TE materials (namely thermal diffusivity, Seebeck coefficient). The thermal diffusivity and thermal conductivity of TiS3 are also measured using photothermal radiometry technique (PTR) and the resulting values of these parameters are α  =  9.7*10‑7 m2 s‑1 and k  =  2.2 W m‑1 K, respectively. The results obtained with the two techniques are in good agreement. In the case of TE materials, the main benefit of the proposed method is related to its non-contact nature and the possibility of obtaining the electric potential and temperature at the same probes. The Seebeck coefficient obtained by active IR thermography (S  =  ‑554 μV K‑1) is consistent with the one obtained using an ULVAC-ZEM3 system (S  =  ‑570 μV K‑1). For a large number of users of thermographic cameras, which are not equipped with a lock-in thermography module, the present approach provides an affordable and cheaper solution.

  11. Briefing book on environmental and waste management activities

    SciTech Connect

    Quayle, T.A.

    1993-04-01

    The purpose of the Briefing Book is to provide current information on Environmental Restoration and Waste Management Activities at the Hanford Site. Each edition updates the information in the previous edition by deleting those sections determined not to be of current interest and adding new topics to keep up to date with the changing requirements and issues. This edition covers the period from October 15, 1992 through April 15, 1993.

  12. United States-Russia: Environmental management activities, Summer 1998

    SciTech Connect

    1998-09-01

    A Joint Coordinating Committee for Environmental Restoration and Waste Management (JCCEM) was formed between the US and Russia. This report describes the areas of research being studied under JCCEM, namely: Efficient separations; Contaminant transport and site characterization; Mixed wastes; High level waste tank remediation; Transuranic stabilization; Decontamination and decommissioning; and Emergency response. Other sections describe: Administrative framework for cooperation; Scientist exchange; Future actions; Non-JCCEM DOE-Russian activities; and JCCEM publications.

  13. Thermal management of quantum cascade lasers in an individually addressable monolithic array architecture

    NASA Astrophysics Data System (ADS)

    Missaggia, Leo; Wang, Christine; Connors, Michael; Saar, Brian; Sanchez-Rubio, Antonio; Creedon, Kevin; Turner, George; Herzog, William

    2016-03-01

    There are a number of military and commercial applications for high-power laser systems in the mid-to-long-infrared wavelength range. By virtue of their demonstrated watt-level performance and wavelength diversity, quantum cascade laser (QCL) and amplifier devices are an excellent choice of emitter for those applications. To realize the power levels of interest, beam combining of arrays of these emitters is required and as a result, array technology must be developed. With this in mind, packaging and thermal management strategies were developed to facilitate the demonstration of a monolithic QCL array operating under CW conditions. Thermal models were constructed and simulations performed to determine the effect of parameters such as array-element ridge width and pitch on gain region temperature rise. The results of the simulations were considered in determining an appropriate QCL array configuration. State-of-the-art micro-impingement cooling along with an electrical distribution scheme comprised of AlN multi-layer technology were integrated into the design. The design of the module allows for individual electrical addressability of the array elements, a method of phase control demonstrated previously for coherent beam combining of diode arrays, along with access to both front and rear facets. Hence, both laser and single-pass amplifier arrays can be accommodated. A module was realized containing a 5 mm cavity length monolithic QCL array comprised of 7 elements on 450 m pitch. An output power of 3.16 W was demonstrated under CW conditions at an emission wavelength of 9μm.

  14. Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district

    SciTech Connect

    Di Maria, Francesco; Micale, Caterina; Morettini, Emanuela; Sisani, Luciano; Damiano, Roberto

    2015-10-15

    Highlights: • LCA analysis of two option for residual waste management. • Exploitation of mechanical physical sorting facility for extracting recyclable from RMSW. • Processing the mechanically sorted organic fraction in bioreactor landfill. • Sensitivity analysis demonstrate high influence for impact assessment of substitution ratio for recycle materials. - Abstract: Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes.

  15. Experimental investigation on the thermal performance of heat storage walls coupled with active solar systems

    NASA Astrophysics Data System (ADS)

    Zhao, Chunyu; You, Shijun; Zhu, Chunying; Yu, Wei

    2016-02-01

    This paper presents an experimental investigation of the performance of a system combining a low-temperature water wall radiant heating system and phase change energy storage technology with an active solar system. This system uses a thermal storage wall that is designed with multilayer thermal storage plates. The heat storage material is expanded graphite that absorbs a mixture of capric acid and lauric acid. An experiment is performed to study the actual effect. The following are studied under winter conditions: (1) the temperature of the radiation wall surface, (2) the melting status of the thermal storage material in the internal plate, (3) the density of the heat flux, and (4) the temperature distribution of the indoor space. The results reveal that the room temperature is controlled between 16 and 20 °C, and the thermal storage wall meets the heating and temperature requirements. The following are also studied under summer conditions: (1) the internal relationship between the indoor temperature distribution and the heat transfer within the regenerative plates during the day and (2) the relationship between the outlet air temperature and inlet air temperature in the thermal storage wall in cooling mode at night. The results indicate that the indoor temperature is approximately 27 °C, which satisfies the summer air-conditioning requirements.

  16. The production of activated carbon using the equipment of thermal power plants and heating plants

    NASA Astrophysics Data System (ADS)

    Osintsev, K. V.; Osintsev, V. V.; Dzhundubaev, A. K.; Kim, S. P.; Al'musin, G. T.; Akbaev, T. A.; Bogatkin, V. I.

    2013-08-01

    The production technology of activated carbon using the conventional equipment of the thermal power stations and boiler houses is proposed. The obtained product is directed into the systems of chemical water preparation and water drain of enterprises. The production cycle is invariable when producing the activated carbon by the proposed technology. The fuel consumption and heat losses are considerably reduced when implementing this technology compared with the known analogs of the carbon sorbent. The production efficiency increases if small dust particles are preliminary separated and coal is activated in narrow ranges of fraction sizes.

  17. Weight Management for Athletes and Active Individuals: A Brief Review.

    PubMed

    Manore, Melinda M

    2015-11-01

    Weight management for athletes and active individuals is unique because of their high daily energy expenditure; thus, the emphasis is usually placed on changing the diet side of the energy balance equation. When dieting for weight loss, active individuals also want to preserve lean tissue, which means that energy restriction cannot be too severe or lean tissue is lost. First, this brief review addresses the issues of weight management in athletes and active individuals and factors to consider when determining a weight-loss goal. Second, the concept of dynamic energy balance is reviewed, including two mathematical models developed to improve weight-loss predictions based on changes in diet and exercise. These models are now available on the Internet. Finally, dietary strategies for weight loss/maintenance that can be successfully used with active individuals are given. Emphasis is placed on teaching the benefits of consuming a low-ED diet (e.g., high-fiber, high-water, low-fat foods), which allows for the consumption of a greater volume of food to increase satiety while reducing energy intake. Health professionals and sport dietitians need to understand dynamic energy balance and be prepared with effective and evidence-based dietary approaches to help athletes and active individuals achieve their body-weight goals. PMID:26553496

  18. Effect of fee-for-service air-conditioning management in balancing thermal comfort and energy usage

    NASA Astrophysics Data System (ADS)

    Chen, Chen-Peng; Hwang, Ruey-Lung; Shih, Wen-Mei

    2014-02-01

    Balancing thermal comfort with the requirement of energy conservation presents a challenge in hot and humid areas where air-conditioning (AC) is frequently used in cooling indoor air. A field survey was conducted in Taiwan to demonstrate the adaptive behaviors of occupants in relation to the use of fans and AC in a school building employing mixed-mode ventilation where AC use was managed under a fee-for-service mechanism. The patterns of using windows, fans, and AC as well as the perceptions of students toward the thermal environment were examined. The results of thermal perception evaluation in relation to the indoor thermal conditions were compared to the levels of thermal comfort predicted by the adaptive models described in the American Society of Heating, Refrigerating, and Air-Conditioning Engineers Standard 55 and EN 15251 and to that of a local model for evaluating thermal adaption in naturally ventilated buildings. A thermal comfort-driven adaptive behavior model was established to illustrate the probability of fans/AC use at specific temperature and compared to the temperature threshold approach to illustrate the potential energy saving the fee-for-service mechanism provided. The findings of this study may be applied as a reference for regulating the operation of AC in school buildings of subtropical regions.

  19. Effect of fee-for-service air-conditioning management in balancing thermal comfort and energy usage.

    PubMed

    Chen, Chen-Peng; Hwang, Ruey-Lung; Shih, Wen-Mei

    2014-11-01

    Balancing thermal comfort with the requirement of energy conservation presents a challenge in hot and humid areas where air-conditioning (AC) is frequently used in cooling indoor air. A field survey was conducted in Taiwan to demonstrate the adaptive behaviors of occupants in relation to the use of fans and AC in a school building employing mixed-mode ventilation where AC use was managed under a fee-for-service mechanism. The patterns of using windows, fans, and AC as well as the perceptions of students toward the thermal environment were examined. The results of thermal perception evaluation in relation to the indoor thermal conditions were compared to the levels of thermal comfort predicted by the adaptive models described in the American Society of Heating, Refrigerating, and Air-Conditioning Engineers Standard 55 and EN 15251 and to that of a local model for evaluating thermal adaption in naturally ventilated buildings. A thermal comfort-driven adaptive behavior model was established to illustrate the probability of fans/AC use at specific temperature and compared to the temperature threshold approach to illustrate the potential energy saving the fee-for-service mechanism provided. The findings of this study may be applied as a reference for regulating the operation of AC in school buildings of subtropical regions. PMID:24510118

  20. Quantifying stream thermal regimes at management-pertinent scales: combining thermal infrared and stationary stream temperature data in a novel modeling framework.

    USGS Publications Warehouse

    Vatland, Shane J.; Gresswell, Robert E.; Poole, Geoffrey C.

    2015-01-01

    Accurately quantifying stream thermal regimes can be challenging because stream temperatures are often spatially and temporally heterogeneous. In this study, we present a novel modeling framework that combines stream temperature data sets that are continuous in either space or time. Specifically, we merged the fine spatial resolution of thermal infrared (TIR) imagery with hourly data from 10 stationary temperature loggers in a 100 km portion of the Big Hole River, MT, USA. This combination allowed us to estimate summer thermal conditions at a relatively fine spatial resolution (every 100 m of stream length) over a large extent of stream (100 km of stream) during during the warmest part of the summer. Rigorous evaluation, including internal validation, external validation with spatially continuous instream temperature measurements collected from a Langrangian frame of reference, and sensitivity analyses, suggests the model was capable of accurately estimating longitudinal patterns in summer stream temperatures for this system Results revealed considerable spatial and temporal heterogeneity in summer stream temperatures and highlighted the value of assessing thermal regimes at relatively fine spatial and temporal scales. Preserving spatial and temporal variability and structure in abiotic stream data provides a critical foundation for understanding the dynamic, multiscale habitat needs of mobile stream organisms. Similarly, enhanced understanding of spatial and temporal variation in dynamic water quality attributes, including temporal sequence and spatial arrangement, can guide strategic placement of monitoring equipment that will subsequently capture variation in environmental conditions directly pertinent to research and management objectives.

  1. The Physical Mechanism for Retinal Discrete Dark Noise: Thermal Activation or Cellular Ultraweak Photon Emission?

    PubMed Central

    Salari, Vahid; Scholkmann, Felix; Bokkon, Istvan; Shahbazi, Farhad; Tuszynski, Jack

    2016-01-01

    For several decades the physical mechanism underlying discrete dark noise of photoreceptors in the eye has remained highly controversial and poorly understood. It is known that the Arrhenius equation, which is based on the Boltzmann distribution for thermal activation, can model only a part (e.g. half of the activation energy) of the retinal dark noise experimentally observed for vertebrate rod and cone pigments. Using the Hinshelwood distribution instead of the Boltzmann distribution in the Arrhenius equation has been proposed as a solution to the problem. Here, we show that the using the Hinshelwood distribution does not solve the problem completely. As the discrete components of noise are indistinguishable in shape and duration from those produced by real photon induced photo-isomerization, the retinal discrete dark noise is most likely due to ‘internal photons’ inside cells and not due to thermal activation of visual pigments. Indeed, all living cells exhibit spontaneous ultraweak photon emission (UPE), mainly in the optical wavelength range, i.e., 350–700 nm. We show here that the retinal discrete dark noise has a similar rate as UPE and therefore dark noise is most likely due to spontaneous cellular UPE and not due to thermal activation. PMID:26950936

  2. Effect of behavioral strategies and activity on thermal comfort of the elderly

    SciTech Connect

    Cena, K.M.; Spotila, J.R.; Ryan, E.B.

    1988-01-01

    A field survey indicated that 101 elderly subjects (mean age 73.4 years) of good health living independently in Hamilton, Ontario, maintained comfort in winter 1985-1986 with a constant mean clothing insulation of 0.8 clo and mean indoor air and operative temperatures at 21,2/degree/C (70.2 F) and 21.5/degree/C (70.7 F), respectively. The subjects scored 83.5 on the Self-Evaluation of Life Function (SELF) scale. Mean activity level at rest was 1.5 met and during periods of light exercise (walking at 1.3 mph, 2 km hr -1) and light domestic household work was 1.9 met. The subjects mean thermal comfort vote at rest was -0.1, very close to a thermal sensation of neutrality (0.0 on a scale from -3 tp +3). This agrees with corresponding measurement (mean of -0.2) of Predicted Mean Vote (PMV) performed with a thermal comfort meter based on the Fanger Comfort Equation. Their thermal comfort vote and PMV during the two periods of increased activity were the same, 0.03. 20 refs., 6 figs., 4 tabs.

  3. Volcanic activity and satellite-detected thermal anomalies at Central American volcanoes

    NASA Technical Reports Server (NTRS)

    Stoiber, R. E. (Principal Investigator); Rose, W. I., Jr.

    1973-01-01

    The author has identified the following significant results. A large nuee ardente eruption occurred at Santiaguito volcano, within the test area on 16 September 1973. Through a system of local observers, the eruption has been described, reported to the international scientific community, extent of affected area mapped, and the new ash sampled. A more extensive report on this event will be prepared. The eruption is an excellent example of the kind of volcanic situation in which satellite thermal imagery might be useful. The Santiaguito dome is a complex mass with a whole series of historically active vents. It's location makes access difficult, yet its activity is of great concern to large agricultural populations who live downslope. Santiaguito has produced a number of large eruptions with little apparent warning. In the earlier ground survey large thermal anomalies were identified at Santiaguito. There is no way of knowing whether satellite monitoring could have detected changes in thermal anomaly patterns related to this recent event, but the position of thermal anomalies on Santiaguito and any changes in their character would be relevant information.

  4. Colloidal particle adsorption at liquid interfaces: capillary driven dynamics and thermally activated kinetics.

    PubMed

    Rahmani, Amir M; Wang, Anna; Manoharan, Vinothan N; Colosqui, Carlos E

    2016-08-14

    The adsorption of single colloidal microparticles (0.5-1 μm radius) at a water-oil interface has been recently studied experimentally using digital holographic microscopy [Kaz et al., Nat. Mater., 2012, 11, 138-142]. An initially fast adsorption dynamics driven by capillary forces is followed by an unexpectedly slow relaxation to equilibrium that is logarithmic in time and can span hours or days. The slow relaxation kinetics has been attributed to the presence of surface "defects" with nanoscale dimensions (1-5 nm) that induce multiple metastable configurations of the contact line perimeter. A kinetic model considering thermally activated transitions between such metastable configurations has been proposed [Colosqui et al., Phys. Rev. Lett., 2013, 111, 028302] to predict both the relaxation rate and the crossover point to the slow logarithmic regime. However, the adsorption dynamics observed experimentally before the crossover point has remained unstudied. In this work, we propose a Langevin model that is able to describe the entire adsorption process of single colloidal particles by considering metastable states produced by surface defects and thermal motion of the particle and liquid interface. Invoking the fluctuation dissipation theorem, we introduce a drag term that considers significant dissipative forces induced by thermal fluctuations of the liquid interface. Langevin dynamics simulations based on the proposed adsorption model yield close agreement with experimental observations for different microparticles, capturing the crossover from (fast) capillary driven dynamics to (slow) thermally activated kinetics. PMID:27373956

  5. First 3D thermal mapping of an active volcano using an advanced photogrammetric method

    NASA Astrophysics Data System (ADS)

    Antoine, Raphael; Baratoux, David; Lacogne, Julien; Lopez, Teodolina; Fauchard, Cyrille; Bretar, Frédéric; Arab-Sedze, Mélanie; Staudacher, Thomas; Jacquemoud, Stéphane; Pierrot-Deseilligny, Marc

    2014-05-01

    to extract 3D informations from thermal images taken from different positions. This paper presents the first 3D thermal map of an active volcano (Piton de la Fournaise, La Réunion Island) directly generated from 70 thermal images (so-called "stereothermogrammetric" DEM). The data were obtained above Dolomieu caldera by helicopter just before sunrise, during a clear weather in 2008. They were obtained before the eruptive events occurring within the Dolomieu caldera. We used a 28 mm focal FLIR Thermacam PM695 lent by the Piton de la Fournaise Observatory. The thermal images were acquired automatically every 30 seconds with the helicopter flying around the caldera at low altitude (less than 100 m height above the caldera). This survey led to the acquisition of images with a ground pixel size in the range of 1-3 m. A particular attention has been brought to the obtaining of a high overlap percentage (80 percents) for the localization of the maximum tie points on the image. Finally, the acquisition of 70 images allowed the generation of a 3D thermal model of the caldera containing more than 500000 points. i.e. 1 point each 2 m², considering a surface of 106 m² for the Dolomieu caldera. This model is then compared with a DEM recently obtained with the LIDAR method after the eruptive events occurring within Dolomieu. The comparison of these independent methods leads to the validation of the stereothermogrammetric method. It allows the quantification of the thickness of the lava flows within the Dolomieu collapse in 2008 and 2009, i.e. approximately 80 meters, as estimated by previous studies from field observations.

  6. IAEA Activities in the Area of Safety Analysis and Accident Management

    SciTech Connect

    Lee, S.; El-Shanawany, M.

    2006-07-01

    Safety analysis is a means of demonstrating how critical safety functions, the integrity of barriers against the release of radioactive materials, and various other safety requirements are fulfilled for a broad range of operating conditions and initiating events. Accordingly, performing safety analysis for a nuclear power plant is one of the most important safety principles. Thermal-hydraulic computer codes are extensively used worldwide for safety analysis by utilities, regulatory authorities, power plant designers and vendors, nuclear fuel companies, research organizations, and technical support organizations. Safety analysis methodology and computer codes have seen a significant development over the last two decades. This fact is also reflected in the work of the International Atomic Energy Agency (IAEA) that aims at increasing the quality and international harmonization of the approaches used in safety analysis. The paper provides an overview of activities and of examples of results obtained recently or planned in the near future in the IAEA's Division of Nuclear Installation Safety in the field of safety analysis for both design basis accidents and beyond design basis accidents as well as accident management. In this paper, specific technical guidance on the safety assessments in the IAEA Safety Standards such as safety analysis methodologies, probabilistic safety assessment, and development of accident management programmes are described. Future trends and related activities in safety analysis and accident management are also introduced. (authors)

  7. Technique for Configuring an Actively Cooled Thermal Shield in a Flight System

    NASA Technical Reports Server (NTRS)

    Barkfknecht, Peter; Mustafi, Shuvo

    2011-01-01

    Broad area cooling shields are a mass-efficient alternative to conductively cooled thermal radiation shielding. The shield would actively intercept a large portion of incident thermal radiation and transport the heat away using cryogenic helium gas. The design concept consists of a conductive and conformable surface that maximizes heat transfer and formability. Broad Area Cooled (BAC) shields could potentially provide considerable mass savings for spaceflight applications by eliminating the need for a rigid thermal radiation shield for cryogen tanks. The BAC consists of a network of capillary tubes that are thermally connected to a conductive shield material. Chilled helium gas is circulated through the network and transports unwanted heat away from the cryogen tanks. The cryogenic helium gas is pumped and chilled simultaneously using a specialized pulse-tube cryocooler, which further improves the mass efficiency of the system. By reducing the thermal environment temperature from 300 to 100 K, the radiative heat load on a cryogen tank could be reduced by an order of magnitude. For a cryogenic liquid propellant scenario of oxygen and hydrogen, the boiloff of hydrogen would be significantly reduced and completely eliminated for oxygen. A major challenge in implementing this technology on large tanks is that the BAC system must be easily scalable from lab demonstrations to full-scale missions. Also, the BAC shield must be conformable to complex shapes like spheres without losing the ability to maintain constant temperature throughout. The initial design maximizes thermal conductivity between the capillary tube and the conductive radiation shielding by using thin, corrugated aluminum foil with the tube running transverse to the folds. This configuration has the added benefit of enabling the foil to stretch and contract longitudinally. This allows the BAC to conform to the complex curvature of a cryogen tank, which is key to its success. To demonstrate a BAC shield

  8. Evaluation of heat sink materials for thermal management of lithium batteries

    NASA Technical Reports Server (NTRS)

    Dimpault-Darcy, E. C.; Miller, K.

    1988-01-01

    Aluminum, neopentyl glycol (NPG), and resins FT and KT are evaluated theoretically and experimentally as heat sink materials for lithium battery packs. The thermal performances of the two resins are compared in a thermal vacuum experiment. As solutions to the sublimation property were not immediately apparent, a theoretical comparison of the thermal performance of NPG versus KT, Al, and no material, is presented.

  9. Carbon sink activity and GHG budget of managed European grasslands

    NASA Astrophysics Data System (ADS)

    Klumpp, Katja; Herfurth, Damien; Soussana, Jean-Francois; Fluxnet Grassland Pi's, European

    2013-04-01

    In agriculture, a large proportion (89%) of greenhouse gas (GHG) emission saving potential may be achieved by means of soil C sequestration. Recent demonstrations of carbon sink activities of European ecosystemes, however, often questioned the existence of C storing grasslands, as though a net sink of C was observed, uncertainty surrounding this estimate was larger than the sink itself (Janssens et al., 2003, Schulze et al., 2009. Then again, some of these estimates were based on a small number of measurements, and on models. Not surprising, there is still, a paucity of studies demonstrating the existence of grassland systems, where C sequestration would exceed (in CO2 equivalents) methane emissions from the enteric fermentation of ruminants and nitrous oxide emissions from managed soils. Grasslands are heavily relied upon for food and forage production. A key component of the carbon sink activity in grasslands is thus the impact of changes in management practices or effects of past and recent management, such as intensification as well as climate (and -variation). We analysed data (i.e. flux, ecological, management and soil organic carbon) from a network of European grassland flux observation sites (36). These sites covered different types and intensities of management, and offered the opportunity to understand grassland carbon cycling and trade-offs between C sinks and CH4 and N2O emissions. For some sites, the assessment of carbon sink activities were compared using two methods; repeated soil inventory and determination of the ecosystem C budget by continuous measurement of CO2 exchange in combination with quantification of other C imports and exports (net C storage, NCS). In general grassland, were a potential sink of C with 60±12 g C /m2.yr (median; min -456; max 645). Grazed sites had a higher NCS compared to cut sites (median 99 vs 67 g C /m2.yr), while permanent grassland sites tended to have a lower NCS compared to temporary sown grasslands (median 64 vs

  10. Thermal Management Optimization of a Thermoelectric-Integrated Methanol Evaporator Using a Compact CFD Modeling Approach

    NASA Astrophysics Data System (ADS)

    Gao, Xin; Chen, Min; Snyder, G. Jeffrey; Andreasen, Søren Juhl; Kær, Søren Knudsen

    2013-07-01

    To better manage the magnitude and direction of the heat flux in an exchanger-based methanol evaporator of a fuel cell system, thermoelectric (TE) modules can be deployed as TE heat flux regulators (TERs). The performance of the TE-integrated evaporator is strongly influenced by its heat exchange structure. The structure transfers the fuel cell exhaust heat to the evaporation chamber to evaporate the methanol, where TE modules are installed in between to facilitate the heat regulation. In this work, firstly, a numerical study is conducted to determine the working currents and working modes of the TERs under the system working condition fluctuations and during the system cold start. A three-dimensional evaporator model is generated in ANSYS FLUENT® by combining a compact TE model with various heat exchange structure geometries. The compact TE model can dramatically improve the computational efficiency, and uses a different material property acquisition method based on module manufacturers' datasheets. Secondly, a simulation study is carried out on the novel evaporator to minimize its thermal resistance and to assess the evaporator pressure drop. The factors studied include the type of fins in the heat exchange structure, the thickness of the fins, the axial conduction penalty, etc. Results show that the TE-integrated evaporator can work more efficiently and smoothly during both load fluctuations and system cold start, offering superior performance.

  11. Design manual for two-phase components of spacecraft thermal management systems

    NASA Astrophysics Data System (ADS)

    Crowley, Christopher J.; Izenson, Michael G.; Barry, James J.; Martin, Jerry L.; Ent, Rebecca S.

    1992-09-01

    This design manual presents methods to design and model the performance of key two-phase components in thermal management systems for spacecraft. Components for both capillary- and mechanically-pumped loops are modeled including: forced-convection evaporators; droplet evaporators; two-phase transport lines, fittings, and tees; shear condensers; capillary condensers; and mechanical pumps. Heat pipe condensers are also included. The methods can be used for component design and sizing, analysis of component performance in system or component development tests, development and evaluation of analytical models for key phenomena, and integration with transient codes for system analysis. This manual describes in detail the analysis methods which have been used to produce software for component design. The software and methods are validated against experimental data whenever such data are available. When possible, simple design maps are presented for initial scoping calculations for sizing two-phase components. The basic analytical approach for these design methods is mechanistic, so that the mathematical models for component behavior are based upon the fundamental physics. Thus, the methods include inherent scaling with gravity, physical size, and fluid properties. This approach allows the models to be easily upgraded as new experimental data become available and includes the ability to assess the analytical uncertainty in design calculations.

  12. CO2 evaporative cooling: The future for tracking detector thermal management

    NASA Astrophysics Data System (ADS)

    Tropea, P.; Daguin, J.; Petagna, P.; Postema, H.; Verlaat, B.; Zwalinski, L.

    2016-07-01

    In the last few years, CO2 evaporative cooling has been one of the favourite technologies chosen for the thermal management of tracking detectors at LHC. ATLAS Insertable B-Layer and CMS Pixel phase 1 upgrade have adopted it and their systems are now operational or under commissioning. The CERN PH-DT team is now merging the lessons learnt on these two systems in order to prepare the design and construction of the cooling systems for the new Upstream Tracker and the Velo upgrade in LHCb, due by 2018. Meanwhile, the preliminary design of the ATLAS and CMS full tracker upgrades is started, and both concepts heavily rely on CO2 evaporative cooling. This paper highlights the performances of the systems now in operation and the challenges to overcome in order to scale them up to the requirements of the future generations of trackers. In particular, it focuses on the conceptual design of a new cooling system suited for the large phase 2 upgrade programmes, which will be validated with the construction of a common prototype in the next years.

  13. The Chevron Foil Thrust Bearing: Improved Performance Through Passive Thermal Management and Effective Lubricant Mixing

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert

    2013-01-01

    An improved foil thrust bearing is described that eliminates or reduces the need for forced cooling of the bearing foils while at the same time improves the load capacity of the bearing, enhances damping, provides overload tolerance, and eliminates the high speed load capacity drop-off that plagues the current state of the art. The performance improvement demonstrated by the chevron foil thrust bearing stems from a novel trailing edge shape that splays the hot lubricant in the thin film radially, thus preventing hot lubricant carry-over into the ensuing bearing sector. Additionally, the chevron shaped trailing edge induces vortical mixing of the hot lubricant with the gas that is naturally resident within the inter-pad region of a foil thrust bearing. The elimination of hot gas carry-over in combination with the enhanced mixing has enabled a completely passive thermally managed foil bearing design. Laboratory testing at NASA has confirmed the original analysis and reduced this concept to practice.

  14. Control of ammonia air pollution through the management of thermal processes in cowsheds.

    PubMed

    Bleizgys, Rolandas; Bagdoniene, Indre

    2016-10-15

    Experimental researches performed in manufacturing cowsheds have demonstrated a variation of ammonia concentration and the factors influencing this most during different periods of the year. The process of ammonia evaporation from manure is influenced by many varying and interrelated factors with temperature and the intensity of air ventilation being the most critical ones. The influence of these factors on the process of ammonia evaporation was established by laboratory researches. An increase in temperature results in an exponential increase in ammonia emission, whereas the dependence of the emission on the air velocity is best expressed by a second degree polynomial. The results obtained may be used as a forecast of the ammonia emissions from cowsheds during different periods of the year. Intensive ventilation is required for the removal of excess moisture from the housing, and this limits the possibilities to reduce ammonia emissions by controlling the intensity of ventilation. A reduction in the amount of ventilation is only recommended if the air quality indices meet the requirements applied to the housing. Better opportunities to reduce ammonia emissions are provided through management of the thermal processes in a cowshed. If the average annual air temperature (11.3°C) is reduced by one degree in a cubicle housing cowshed, the ammonia emissions will decrease by 10%. PMID:27350091

  15. Research of surface activating influence on formation of adhesion between gas-thermal coating and steel substrate

    NASA Astrophysics Data System (ADS)

    Kovalevskaya, Z.; Klimenov, V.; Zaitsev, K.

    2015-09-01

    Estimation of influence of physical and thermal activating on adhesion between steel substrates and thermal coatings has been performed. The substrates with surfaces obtained by and ultrasonic surface plastic deformation were used. To evaluate physical activating, preheating of the substrates to 600°C was performed. To evaluate the effect of thermal activating, the substrate surfaces after interfacial detachment were examined. Bonded areas on the substrate surfaces were measured by means of optical profilometry. The experiments have shown that surface physical activating is the main factor in formation of the adhesive bond between the coating and the substrate processed with the proposed methods.

  16. Blue thermally activated delayed fluorescence materials based on bis(phenylsulfonyl)benzene derivatives.

    PubMed

    Liu, Ming; Seino, Yuki; Chen, Dongcheng; Inomata, Susumu; Su, Shi-Jian; Sasabe, Hisahiro; Kido, Junji

    2015-11-25

    Two blue thermally activated delayed fluorescence molecules based on bis(phenylsulfonyl)benzene with very small singlet-triplet splitting energy were designed and synthesized by combining 3,6-di-tert-butylcarbazole with 1,4-bis(phenylsulfonyl)benzene and 1,3-bis(phenylsulfonyl)benzene, and a maximum external quantum efficiency of 11.7% was achieved for an electroluminescent device. PMID:26405720

  17. Increased water activity reduces the thermal resistance of Salmonella enterica in peanut butter.

    PubMed

    He, Yingshu; Li, Ye; Salazar, Joelle K; Yang, Jingyun; Tortorello, Mary Lou; Zhang, Wei

    2013-08-01

    Increased water activity in peanut butter significantly (P < 0.05) reduced the heat resistance of desiccation-stressed Salmonella enterica serotypes treated at 90 °C. The difference in thermal resistance was less notable when strains were treated at 126 °C. Using scanning electron microscopy, we observed minor morphological changes of S. enterica cells resulting from desiccation and rehydration processes in peanut oil. PMID:23728806

  18. Thermally Activated Delayed Fluorescence Polymers for Efficient Solution-Processed Organic Light-Emitting Diodes.

    PubMed

    Lee, Sae Youn; Yasuda, Takuma; Komiyama, Hideaki; Lee, Jiyoung; Adachi, Chihaya

    2016-06-01

    Thermally activated delayed fluorescence (TADF) π-conjugated polymers are developed for solution-processed TADF-OLEDs. Benzophenone-based alternating donor-acceptor structures contribute to the small ∆EST , enabling efficient exciton-harvesting through TADF. Solution-processed OLEDs using the TADF polymers as emitters can achieve high maximum external electroluminescence efficiencies of up to 9.3%. PMID:27001891

  19. Evolution of thermal response properties in a cold-activated TRP channel.

    PubMed

    Myers, Benjamin R; Sigal, Yaron M; Julius, David

    2009-01-01

    Animals sense changes in ambient temperature irrespective of whether core body temperature is internally maintained (homeotherms) or subject to environmental variation (poikilotherms). Here we show that a cold-sensitive ion channel, TRPM8, displays dramatically different thermal activation ranges in frogs versus mammals or birds, consistent with variations in these species' cutaneous and core body temperatures. Thus, somatosensory receptors are not static through evolution, but show functional diversity reflecting the characteristics of an organism's ecological niche. PMID:19492038

  20. The design of dual emitting cores for green thermally activated delayed fluorescent materials.

    PubMed

    Cho, Yong Joo; Jeon, Sang Kyu; Chin, Byung Doo; Yu, Eunsun; Lee, Jun Yeob

    2015-04-20

    Dual emitting cores for thermally activated delayed fluorescent (TADF) emitters were developed. Relative to the corresponding TADF emitter with a single emitting core the TADF emitter with a dual emitting core, 3,3',5,5'-tetra(carbazol-9-yl)-[1,1'-biphenyl]-2,2',6,6'-tetracarbonitrile, showed enhanced light absorption accompanied by a high photoluminescence quantum yield. The quantum and power efficiencies of the TADF devices were enhanced by the dual emitting cores. PMID:25727757

  1. ION TEMPERATURE AND NON-THERMAL VELOCITY IN A SOLAR ACTIVE REGION: USING EMISSION LINES OF DIFFERENT ATOMIC SPECIES

    SciTech Connect

    Imada, S.; Hara, H.; Watanabe, T.

    2009-11-10

    We have studied the characteristics of the ion thermal temperature and non-thermal velocity in an active region observed by the EUV Imaging Spectrometer onboard Hinode. We used two emission lines of different atomic species (Fe XVI 262.98 A and S XIII 256.69 A) to distinguish the ion thermal velocity from the observed full width at half-maximum. We assumed that the sources of the two emission lines are the same thermal temperature. We also assumed that they have the same non-thermal velocity. With these assumptions, we could obtain the ion thermal temperature, after noting that M{sub sulfur} approx 0.6M{sub iron}. We have carried out the ion thermal temperature analysis in the active region where the photon counts are sufficient (>4500). What we found is as follows: (1) the common ion thermal temperatures obtained by Fe XVI and S XIII are approx2.5 MK, (2) the typical non-thermal velocities are approx13 km s{sup -1}, (3) the highest non-thermal velocities (>20 km s{sup -1}) are preferentially observed between the bright points in Fe XVI, while (4) the hottest material (>3 MK) is observed relatively inside the bright points compared with the highest non-thermal velocity region.

  2. Investigations on Repository Near-Field Thermal Modeling - Repository Science/Thermal Load Management & Design Concepts (M41UF033302)

    SciTech Connect

    Sutton, M; Blink, J A; Fratoni, M; Greenberg, H R; Ross, A D

    2011-07-15

    The various layers of material from the waste package (such as components of the engineered barrier system and the host rock surface) to a given distance within the rock wall at a given distance can be described as concentric circles with varying thermal properties (see Figure 5.1-1). The selected model approach examines the contributions of the waste package, axial waste package neighbors and lateral neighboring emplacement drifts (see Section 5.2.1 and Appendix H, Section 2). In clay and deep borehole media, the peak temperature is driven by the central waste package whereas, in granite and salt, the contribution to the temperature rise by adjacent (lateral) waste packages in drift or emplacement borehole lines is dominant at the time of the peak temperature. Mathematical models generated using Mathcad software provide insight into the effects of changing waste package spacing for six waste forms, namely UOX, MOX, co-extraction, new extraction, E-Chem ceramic and E-Chem metal in four different geologic media (granite, clay, salt and deep borehole). Each scenario includes thermal conductivity and diffusivity for each layer between the waste package and the host rock, dimensions of representative repository designs (such as waste package spacing, drift or emplacement borehole spacing, waste package dimensions and layer thickness), and decay heat curves generated from knowledge of the contents of a given waste form after 10, 50, 100 and 200 years of surface storage. Key results generated for each scenario include rock temperature at a given time calculated at a given radius from the central waste package (Section 5.2.1 and Appendix H, Section 3), the corresponding temperature at the interface of the waste package and EBS material, and at each EBS layer in between (Section 5.2.2 and Appendix H, Section 4). This information is vital to understand the implications of repository design (waste package capacity, surface storage time, waste package spacing, and emplacement

  3. Orion Active Thermal Control System Dynamic Modeling Using Simulink/MATLAB

    NASA Technical Reports Server (NTRS)

    Wang, Xiao-Yen J.; Yuko, James

    2010-01-01

    This paper presents dynamic modeling of the crew exploration vehicle (Orion) active thermal control system (ATCS) using Simulink (Simulink, developed by The MathWorks). The model includes major components in ATCS, such as heat exchangers and radiator panels. The mathematical models of the heat exchanger and radiator are described first. Four different orbits were used to validate the radiator model. The current model results were compared with an independent Thermal Desktop (TD) (Thermal Desktop, PC/CAD-based thermal model builder, developed in Cullimore & Ring (C&R) Technologies) model results and showed good agreement for all orbits. In addition, the Orion ATCS performance was presented for three orbits and the current model results were compared with three sets of solutions- FloCAD (FloCAD, PC/CAD-based thermal/fluid model builder, developed in C&R Technologies) model results, SINDA/FLUINT (SINDA/FLUINT, a generalized thermal/fluid network-style solver ) model results, and independent Simulink model results. For each case, the fluid temperatures at every component on both the crew module and service module sides were plotted and compared. The overall agreement is reasonable for all orbits, with similar behavior and trends for the system. Some discrepancies exist because the control algorithm might vary from model to model. Finally, the ATCS performance for a 45-hr nominal mission timeline was simulated to demonstrate the capability of the model. The results show that the ATCS performs as expected and approximately 2.3 lb water was consumed in the sublimator within the 45 hr timeline before Orion docked at the International Space Station.

  4. 78 FR 21118 - Agency Information Collection Activities; Submission to the Office of Management and Budget for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-09

    ... Agency Information Collection Activities; Submission to the Office of Management and Budget for Review... includes all schools that are not supported primarily by public funds, that provide classroom instruction... Management Services, Office of Management. BILLING CODE 4000-01-P...

  5. Reportable Nuclide Criteria for ORNL Radioactive Waste Management Activities - 13005

    SciTech Connect

    McDowell, Kip; Forrester, Tim; Saunders, Mark

    2013-07-01

    The U.S. Department of Energy's Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee generates numerous radioactive waste streams. Many of those streams contain a large number of radionuclides with an extremely broad range of concentrations. To feasibly manage the radionuclide information, ORNL developed reportable nuclide criteria to distinguish between those nuclides in a waste stream that require waste tracking versus those nuclides of such minimal activity that do not require tracking. The criteria include tracking thresholds drawn from ORNL onsite management requirements, transportation requirements, and relevant treatment and disposal facility acceptance criteria. As a management practice, ORNL maintains waste tracking on a nuclide in a specific waste stream if it exceeds any of the reportable nuclide criteria. Nuclides in a specific waste stream that screen out as non-reportable under all these criteria may be dropped from ORNL waste tracking. The benefit of these criteria is to ensure that nuclides in a waste stream with activities which meaningfully affect safety and compliance are tracked, while documenting the basis for removing certain isotopes from further consideration. (authors)

  6. Reportable Nuclide Criteria for ORNL Waste Management Activities - 13005

    SciTech Connect

    McDowell, Kip; Forrester, Tim; Saunders, Mark Edward

    2013-01-01

    The U.S. Department of Energy's Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee generates numerous radioactive waste streams. Many of those streams contain a large number of radionuclides with an extremely broad range of concentrations. To feasibly manage the radionuclide information, ORNL developed a reportable nuclide criteria to distinguish between those nuclides in a waste stream that require waste tracking versus those nuclides of such minimal activity that do not require tracking. The criteria include tracking thresholds drawn from ORNL onsite management requirements, transportation requirements, and relevant treatment and disposal facility acceptance criteria. As a management practice, ORNL maintains waste tracking on a nuclide in a specific waste stream if it exceeds any of the reportable nuclide criteria. Nuclides in a specific waste stream that screen out as non-reportable under all these criteria may be dropped from ORNL waste tracking. The benefit of this criteria is to ensure that nuclides in a waste stream with activities which meaningfully affect safety and compliance are tracked, while documenting the basis for removing certain isotopes from further consideration.

  7. Detectability of thermal signatures associated with active formation of 'chaos terrain' on Europa

    NASA Astrophysics Data System (ADS)

    Abramov, Oleg; Rathbun, Julie A.; Schmidt, Britney E.; Spencer, John R.

    2013-12-01

    A recent study by Schmidt et al. (2011) suggests that Thera Macula, one of the "chaos regions" on Europa, may be actively forming over a large liquid water lens. Such a process could conceivably produce a thermal anomaly detectable by a future Europa orbiter or flyby mission, allowing for a direct verification of this finding. Here, we present a set of models that quantitatively assess the surface and subsurface temperatures associated with an actively resurfacing chaos region using constraints from Thera Macula. The results of this numerical study suggest that the surface temperature over an active chaos region can be as high as ˜200 K. However, low-resolution Galileo Photo-Polarimeter Radiometer (PPR) observations indicate temperatures below 120 K over Thera Macula. This suggests that Thera Macula is not currently active unless an insulating layer of at least a few centimeters in thickness is present, or activity is confined to small regions, reducing the overall intensity of the thermal signature. Alternatively, Thera may have been cooling for at least 10-100 yr and still contain a subsurface lake, which can take ˜300,000 yr to crystallize. According to the present study, a more sensitive instrument capable of detecting anomalies ˜5 K above ambient could detect activity at Thera Macula even if an insulating layer of ˜50 cm is present.

  8. Thermally Reduced Graphene Oxide Electrochemically Activated by Bis-Spiro Quaternary Alkyl Ammonium for Capacitors.

    PubMed

    He, Tieshi; Meng, Xiangling; Nie, Junping; Tong, Yujin; Cai, Kedi

    2016-06-01

    Thermally reduced graphene oxide (RGO) electrochemically activated by a quaternary alkyl ammonium-based organic electrolytes/activated carbon (AC) electrode asymmetric capacitor is proposed. The electrochemical activation process includes adsorption of anions into the pores of AC in the positive electrode and the interlayer intercalation of cations into RGO in the negative electrode under high potential (4.0 V). The EA process of RGO by quaternary alkyl ammonium was investigated by X-ray diffraction and electrochemical measurements, and the effects of cation size and structure were extensively evaluated. Intercalation by quaternary alkyl ammonium demonstrates a small degree of expansion of the whole crystal lattice (d002) and a large degree of expansion of the partial crystal lattice (d002) of RGO. RGO electrochemically activated by bis-spiro quaternary alkyl ammonium in propylene carbonate/AC asymmetric capacitor exhibits good activated efficiency, high specific capacity, and stable cyclability. PMID:27180820

  9. Activation energy of negative fixed charges in thermal ALD Al2O3

    NASA Astrophysics Data System (ADS)

    Kühnhold-Pospischil, S.; Saint-Cast, P.; Richter, A.; Hofmann, M.

    2016-08-01

    A study of the thermally activated negative fixed charges Qtot and the interface trap densities Dit at the interface between Si and thermal atomic-layer-deposited amorphous Al2O3 layers is presented. The thermal activation of Qtot and Dit was conducted at annealing temperatures between 220 °C and 500 °C for durations between 3 s and 38 h. The temperature-induced differences in Qtot and Dit were measured using the characterization method called corona oxide characterization of semiconductors. Their time dependency were fitted using stretched exponential functions, yielding activation energies of EA = (2.2 ± 0.2) eV and EA = (2.3 ± 0.7) eV for Qtot and Dit, respectively. For annealing temperatures from 350 °C to 500 °C, the changes in Qtot and Dit were similar for both p- and n-type doped Si samples. In contrast, at 220 °C the charging process was enhanced for p-type samples. Based on the observations described in this contribution, a charging model leading to Qtot based on an electron hopping process between the silicon and Al2O3 through defects is proposed.

  10. Transient Thermal State of an Active Braille Matrix with Incorporated Thermal Actuators by Means of Finite Element Method

    ERIC Educational Resources Information Center

    Alutei, Alexandra-Maria; Szelitzky, Emoke; Mandru, Dan

    2013-01-01

    In this article the authors present the transient thermal analysis for a developed thermal linear actuator based on wax paraffin used to drive the cells of a Braille device. A numerical investigation of transient heat transfer phenomenon during paraffin melting and solidification in an encapsulated recipient has been carried out using the ANSYS…

  11. Activity Management System user reference manual. Revision 1

    SciTech Connect

    Gates, T.A.; Burdick, M.B.

    1994-09-22

    The Activity Management System (AMS) was developed in response to the need for a simple-to-use, low-cost, user interface system for collecting and logging Hanford Waste Vitrification Plant Project (HWVP) activities. This system needed to run on user workstations and provide common user access to a database stored on a local network file server. Most important, users wanted a system that provided a management tool that supported their individual process for completing activities. Existing system treated the performer as a tool of the system. All AMS data is maintained in encrypted format. Users can feel confident that any activities they have entered into the database are private and that, as the originator, they retain sole control over who can see them. Once entered into the AMS database, the activities cannot be accessed by anyone other than the originator, the designated agent, or by authorized viewers who have been explicitly granted the right to look at specific activities by the originator. This user guide is intended to assist new AMS users in learning how to use the application and, after the initial learning process, will serve as an ongoing reference for experienced users in performing infrequently used functions. Online help screens provide reference to some of the key information in this manual. Additional help screens, encompassing all the applicable material in this manual, will be incorporated into future AMS revisions. A third, and most important, source of help is the AMS administrator(s). This guide describes the initial production version of AMS, which has been designated Revision 1.0.

  12. Management and climate contributions to satellite-derived active fire trends in the contiguous United States

    NASA Astrophysics Data System (ADS)

    Lin, Hsiao-Wen; McCarty, Jessica L.; Wang, Dongdong; Rogers, Brendan M.; Morton, Douglas C.; Collatz, G. James; Jin, Yufang; Randerson, James T.

    2014-04-01

    Fires in croplands, plantations, and rangelands contribute significantly to fire emissions in the United States, yet are often overshadowed by wildland fires in efforts to develop inventories or estimate responses to climate change. Here we quantified decadal trends, interannual variability, and seasonality of Terra Moderate Resolution Imaging Spectroradiometer (MODIS) observations of active fires (thermal anomalies) as a function of management type in the contiguous U.S. during 2001-2010. We used the Monitoring Trends in Burn Severity database to identify active fires within the perimeter of large wildland fires and land cover maps to identify active fires in croplands. A third class of fires defined as prescribed/other included all residual satellite active fire detections. Large wildland fires were the most variable of all three fire types and had no significant annual trend in the contiguous U.S. during 2001-2010. Active fires in croplands, in contrast, increased at a rate of 3.4% per year. Cropland and prescribed/other fire types combined were responsible for 77% of the total active fire detections within the U.S and were most abundant in the south and southeast. In the west, cropland active fires decreased at a rate of 5.9% per year, likely in response to intensive air quality policies. Potential evaporation was a dominant regulator of the interannual variability of large wildland fires, but had a weaker influence on the other two fire types. Our analysis suggests it may be possible to modify landscape fire emissions within the U.S. by influencing the way fires are used in managed ecosystems.

  13. Management and climate contributions to satellite-derived active fire trends in the contiguous United States

    PubMed Central

    Lin, Hsiao-Wen; McCarty, Jessica L; Wang, Dongdong; Rogers, Brendan M; Morton, Douglas C; Collatz, G James; Jin, Yufang; Randerson, James T

    2014-01-01

    Fires in croplands, plantations, and rangelands contribute significantly to fire emissions in the United States, yet are often overshadowed by wildland fires in efforts to develop inventories or estimate responses to climate change. Here we quantified decadal trends, interannual variability, and seasonality of Terra Moderate Resolution Imaging Spectroradiometer (MODIS) observations of active fires (thermal anomalies) as a function of management type in the contiguous U.S. during 2001–2010. We used the Monitoring Trends in Burn Severity database to identify active fires within the perimeter of large wildland fires and land cover maps to identify active fires in croplands. A third class of fires defined as prescribed/other included all residual satellite active fire detections. Large wildland fires were the most variable of all three fire types and had no significant annual trend in the contiguous U.S. during 2001–2010. Active fires in croplands, in contrast, increased at a rate of 3.4% per year. Cropland and prescribed/other fire types combined were responsible for 77% of the total active fire detections within the U.S and were most abundant in the south and southeast. In the west, cropland active fires decreased at a rate of 5.9% per year, likely in response to intensive air quality policies. Potential evaporation was a dominant regulator of the interannual variability of large wildland fires, but had a weaker influence on the other two fire types. Our analysis suggests it may be possible to modify landscape fire emissions within the U.S. by influencing the way fires are used in managed ecosystems. Key Points Wildland, cropland, and prescribed fires had different trends and patterns Sensitivity to climate varied with fire type Intensity of air quality regulation influenced cropland burning trends PMID:26213662

  14. Time series analysis of thermal variation on Italian volcanic active areas by using IR satellite data

    NASA Astrophysics Data System (ADS)

    Silvestri, M.; Buongiorno, M. F.; Pieri, D. C.

    2014-12-01

    To monitoring of active volcanoes the systematic acquisition of medium/high resolution thermal data and the subsequent analysis of time series may improve the capability to detect small surface temperature variation related to changes in volcanic activity level and contribute to the early warning systems. Examples on the processing of long time series based EO data of Mt Etna activity and Phlegraean Fields observation by using remote sensing techniques and at different spatial resolution data (ASTER - 90mt, AVHRR -1km, MODIS-1km, MSG SEVIRI-3km) are showed. The use of TIR sensors with high spatial resolution offers the possibility to obtain detailed information on the areas where there are significant changes, detecting variation in fumaroles fields and summit craters before eruptions. Thanks to ASTER thermal infrared (TIR, 5 bands) regions of the electromagnetic spectrum we have obtained the surface temperature map on the volcano area. For this study we have considered the ASTER's night observations that show well defined episodes of increasing thermal emission of crater thanks to a more uniform background temperature. Two different procedures are shown, both using the TIR high spatial resolution data: for Phlegraean Fields (active but quiescent volcano) the analysis of time series of surface temperature which may improve the capability to detect small surface temperature variation related to changes in volcanic activity level; for Mt. Etna (active volcano) a semi-automatic procedure which extract the summit area radiance values with the goal of detecting variation related to eruptive events. The advantage of direct download of EO data by means INGV antennas even though low spatial resolution offers the possibility of a systematic data processing having a daily updating of information for prompt response and hazard mitigation. At the same time the comparison of surface temperature retrievals at different scale is an important issue for future satellite sensors.

  15. Waste management activities and carbon emissions in Africa

    SciTech Connect

    Couth, R.; Trois, C.

    2011-01-15

    This paper summarizes research into waste management activities and carbon emissions from territories in sub-Saharan Africa with the main objective of quantifying emission reductions (ERs) that can be gained through viable improvements to waste management in Africa. It demonstrates that data on waste and carbon emissions is poor and generally inadequate for prediction models. The paper shows that the amount of waste produced and its composition are linked to national Gross Domestic Product (GDP). Waste production per person is around half that in developed countries with a mean around 230 kg/hd/yr. Sub-Saharan territories produce waste with a biogenic carbon content of around 56% (+/-25%), which is approximately 40% greater than developed countries. This waste is disposed in uncontrolled dumps that produce large amounts of methane gas. Greenhouse gas (GHG) emissions from waste will rise with increasing urbanization and can only be controlled through funding mechanisms from developed countries.

  16. Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district.

    PubMed

    Di Maria, Francesco; Micale, Caterina; Morettini, Emanuela; Sisani, Luciano; Damiano, Roberto

    2015-10-01

    Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes. PMID:26184897

  17. Activation of thermal denudation under recent climatic fluctuations, Central Yamal, Russia

    NASA Astrophysics Data System (ADS)

    Khomutov, Artem; Dvornikov, Yury; Gubarkov, Anatoly; Mullanurov, Damir

    2016-04-01

    Climatic fluctuations over the past few years significantly affected the increase of cryogenic processes activity in the tundra zone of the Yamal Peninsula. On Central Yamal a large-scale cryogenic landsliding was observed in 1989, while cryogenic earth flows were actively developing since 2012 through tabular ground ice thawing. As a result, thermocirques form on lakeshores. Key area (research station "Vaskiny Dachi" on the Se-Yakha and the Mordy-Yakha interfluve) during the period from 1989 to 2012 was characterized by a local occurrence of thermal denudation. By 2010, remote sensing data showed that this process in the study area was usually inactive and thermocirques looked stabilized, overgrown by vegetation. Extremely warm summer of 2012 resulted in formation of new thermal denudation features, such as cryogenic translational landslides, cryogenic earth flows and furthermore, thermocirques, complex landforms resulting from ice wedges and tabular ground ice thaw. The 2012 warm season was characterized by a deeper active layer: at the end of the warm period deeper by 15% than the average for the 1993-2011. Observed were indications of a high pore pressure in the active layer: effuse of liquefied clay in the tension cracks on many slopes. By 2013, according to the field and remote sensing data, there were more than 90 active thermal denudation landforms from 66 to 25000 sq.m in size on the territory of 345 sq.km. Thus, at the present in the tundra of the Yamal Peninsula the predominance of the processes associated with tabular ground ice thawing (cryogenic earth flows) over the processes associated with the ice formation at the bottom of the active layer (cryogenic translational landslides) is observed. It is caused by both a periodic deepening of the active layer, and consecutive increase of ground temperature. Activation of thermal denudation observed on the Yamal Peninsula last years is associated with extremely warm spring and summer of 2012. By the end of

  18. Competition between thermally activated and tip-induced hopping of indium atoms on Si(100)

    NASA Astrophysics Data System (ADS)

    Setvín, Martin; Javorský, Jakub; Majzik, Zsolt; Sobotík, Pavel; Kocán, Pavel; Ošt'Ádal, Ivan

    2012-02-01

    The adsorption and dynamics of single indium atoms on a Si(100) surface were studied by means of scanning tunneling microscopy in a temperature range from 30 to 130 K. Single In adatoms are strongly influenced by a tip-surface interaction which is proportional to the tunneling current. The surface hopping of the In adatoms was recorded and conditions minimizing the tip-surface interaction were investigated. The activation energies and frequency prefactors for thermally activated hopping were calculated from a temperature dependence of lifetimes of In adatoms in adsorption positions.

  19. Pollution effects on fisheries — potential management activities

    NASA Astrophysics Data System (ADS)

    Sindermann, C. J.

    1980-03-01

    Management of ocean pollution must be based on the best available scientific information, with adequate consideration of economic, social, and political realities. Unfortunately, the best available scientific information about pollution effects on fisheries is often fragmentary, and often conjectural; therefore a primary concern of management should be a critical review and assessment of available factual information about effects of pollutants on fish and shellfish stocks. A major problem in any such review and assessment is the separation of pollutant effects from the effects of all the other environmental factors that influence survival and well-being of marine animals. Data from long-term monitoring of resource abundance, and from monitoring of all determinant environmental variables, will be required for analyses that lead to resolution of the problem. Information must also be acquired about fluxes of contaminants through resource-related ecosystems, and about contaminant effects on resource species as demonstrated in field and laboratory experiments. Other possible management activities include: (1) encouragement of continued efforts to document clearly the localized and general effects of pollution on living resources; (2) continued pressure to identify and use reliable biological indicators of environmental degradation (indicators of choice at present are: unusually high levels of genetic and other anomalies in the earliest life history stages; presence of pollution-associated disease signs, particularly fin erosion and ulcers, in fish; and biochemical/physiological changes); and (3) major efforts to reduce inputs of pollutants clearly demonstrated to be harmful to living resources, from point sources as well as ocean dumping. Such pollution management activities, based on continuous efforts in stock assessment, environmental assessment, and experimental studies, can help to insure that rational decisions will be made about uses and abuses of coastal

  20. Finger heat flux/temperature as an indicator of thermal imbalance with application for extravehicular activity

    NASA Astrophysics Data System (ADS)

    Koscheyev, Victor S.; Leon, Gloria R.; Coca, Aitor

    2005-11-01

    The designation of a simple, non-invasive, and highly precise method to monitor the thermal status of astronauts is important to enhance safety during extravehicular activities (EVA) and onboard emergencies. Finger temperature ( Tfing), finger heat flux, and indices of core temperature ( Tc) [rectal ( Tre), ear canal ( Tec)] were assessed in 3 studies involving different patterns of heat removal/insertion from/to the body by a multi-compartment liquid cooling/warming garment (LCWG). Under both uniform and nonuniform temperature conditions on the body surface, Tfing and finger heat flux were highly correlated with garment heat flux, and also highly correlated with each other. Tc responses did not adequately reflect changes in thermal balance during the ongoing process of heat insertion/removal from the body. Overall, Tfing/finger heat flux adequately reflected the initial destabilization of thermal balance, and therefore appears to have significant potential as a useful index for monitoring and maintaining thermal balance and comfort in extreme conditions in space as well as on Earth.