Science.gov

Sample records for active tractor beams

  1. Tractor beams for optical micromanipulation

    NASA Astrophysics Data System (ADS)

    Yevick, Aaron; Grier, David G.

    2016-03-01

    Tractor beams are traveling waves that transport illuminated objects in the retrograde direction relative to the direction of propagation. The theory of photokinetic effects identifies design criteria for long-range general- purpose tractor beams. These criteria distinguish first-order tractor beams that couple to induced dipole moments from higher-order tractor beams that rely on coupling to higher-order multipole moments to achieve pulling. First-order tractor beams are inherently longer-ranged and operate on a wider variety of materials. We explore the physics of first-order tractor beams in the context of a family of generalized solenoidal waves.

  2. Acoustic tractor beam.

    PubMed

    Démoré, Christine E M; Dahl, Patrick M; Yang, Zhengyi; Glynne-Jones, Peter; Melzer, Andreas; Cochran, Sandy; MacDonald, Michael P; Spalding, Gabriel C

    2014-05-01

    Negative radiation forces act opposite to the direction of propagation, or net momentum, of a beam but have previously been challenging to definitively demonstrate. We report an experimental acoustic tractor beam generated by an ultrasonic array operating on macroscopic targets (>1 cm) to demonstrate the negative radiation forces and to map out regimes over which they dominate, which we compare to simulations. The result and the geometrically simple configuration show that the effect is due to nonconservative forces, produced by redirection of a momentum flux from the angled sides of a target and not by conservative forces from a potential energy gradient. Use of a simple acoustic setup provides an easily understood illustration of the negative radiation pressure concept for tractor beams and demonstrates continuous attraction towards the source, against a net momentum flux in the system. PMID:24836252

  3. Acoustic Tractor Beam

    NASA Astrophysics Data System (ADS)

    Démoré, Christine E. M.; Dahl, Patrick M.; Yang, Zhengyi; Glynne-Jones, Peter; Melzer, Andreas; Cochran, Sandy; MacDonald, Michael P.; Spalding, Gabriel C.

    2014-05-01

    Negative radiation forces act opposite to the direction of propagation, or net momentum, of a beam but have previously been challenging to definitively demonstrate. We report an experimental acoustic tractor beam generated by an ultrasonic array operating on macroscopic targets (>1 cm) to demonstrate the negative radiation forces and to map out regimes over which they dominate, which we compare to simulations. The result and the geometrically simple configuration show that the effect is due to nonconservative forces, produced by redirection of a momentum flux from the angled sides of a target and not by conservative forces from a potential energy gradient. Use of a simple acoustic setup provides an easily understood illustration of the negative radiation pressure concept for tractor beams and demonstrates continuous attraction towards the source, against a net momentum flux in the system.

  4. Dynamic acoustic tractor beams

    NASA Astrophysics Data System (ADS)

    Mitri, F. G.

    2015-03-01

    Pulling a sphere and vibrating it around an equilibrium position by amplitude-modulation in the near-field of a single finite circular piston transducer is theoretically demonstrated. Conditions are found where a fluid hexane sphere (with arbitrary radius) chosen as an example, centered on the axis of progressive propagating waves and submerged in non-viscous water, experiences an attractive (steady) force pulling it towards the transducer, as well as an oscillatory force forcing it to vibrate back-and-forth. Numerical predictions for the dynamic force illustrate the theory and suggest an innovative method in designing dynamic acoustical tractor beams.

  5. Dynamic acoustic tractor beams

    SciTech Connect

    Mitri, F. G.

    2015-03-07

    Pulling a sphere and vibrating it around an equilibrium position by amplitude-modulation in the near-field of a single finite circular piston transducer is theoretically demonstrated. Conditions are found where a fluid hexane sphere (with arbitrary radius) chosen as an example, centered on the axis of progressive propagating waves and submerged in non-viscous water, experiences an attractive (steady) force pulling it towards the transducer, as well as an oscillatory force forcing it to vibrate back-and-forth. Numerical predictions for the dynamic force illustrate the theory and suggest an innovative method in designing dynamic acoustical tractor beams.

  6. Plane waves as tractor beams

    NASA Astrophysics Data System (ADS)

    Forgács, Péter; Lukács, Árpád; Romańczukiewicz, Tomasz

    2013-12-01

    It is shown that in a large class of systems, plane waves act as tractor beams: i.e., an incident plane wave can exert a pulling force on the scatterer. The underlying physical mechanism for the pulling force is due to the sufficiently strong scattering of the incoming wave into another mode carrying more momentum, in which case excess momentum is created behind the scatterer. This tractor beam or negative radiation pressure (NRP) effect, is found to be generic in systems with multiple scattering channels. In a birefringent medium, electromagnetic plane waves incident on a thin plate exert NRP of the same order of magnitude as optical radiation pressure, while in artificial dielectrics (metamaterials), the magnitude of NRP can even be macroscopic. In two dimensions, we study various scattering situations on vortices, and NRP is shown to occur by the scattering of heavy baryons into light leptons off cosmic strings, and by neutron scattering off vortices in the XY model.

  7. Generating stable tractor beams with dielectric metasurfaces

    NASA Astrophysics Data System (ADS)

    Pfeiffer, Carl; Grbic, Anthony

    2015-03-01

    Propagation-invariant beams that pull objects towards a light source are commonly known as tractor beams. Here, an efficient, linearly polarized tractor beam with improved stability is introduced. The beam consists of a superposition of transverse-electric and transverse-magnetic polarized Bessel beams of orders m =+1 and m =-1 . It is shown that this beam can stably pull a wide range of dielectric microparticles arbitrarily long distances, independent of ambient conditions. Next, a straightforward method of generating these high-performance beams is proposed. A Si metasurface transforms an incident linearly polarized Gaussian beam into the desired tractor beam. Full-wave simulations demonstrate that it is possible for this simple geometry to pull a polystyrene sphere a distance equal to the nondiffracting range of the Bessel beam. The simplicity of the setup and the robust performance of the proposed tractor beam significantly enhance the ability to manipulate matter with light.

  8. Tractor beams in the Rayleigh limit

    NASA Astrophysics Data System (ADS)

    Yevick, Aaron; Ruffner, David B.; Grier, David G.

    2016-04-01

    A tractor beam is a traveling wave that transports illuminated objects back to its source, opposite to the wave's direction of propagation, along its entire length. The requisite retrograde force arises when an object scatters the wave's momentum density downstream into the direction of propagation and then recoils upstream by conservation of momentum. Achieving this condition imposes constraints on the structure of the wave, which we elucidate in the Rayleigh limit, when the wavelength exceeds the size of the object. Continuously propagation-invariant modes such as Bessel beams do not satisfy these conditions at dipole order in the multipole expansion and so cannot serve as general-purpose long-ranged tractor beams. Modes with discrete propagation invariance, however, can act as first-order tractor beams. We demonstrate this by introducing a class of minimal solenoidal waves together with a set of design criteria that distinguish tractor beams that pull objects from repulsor beams that push them.

  9. Making 'Tractor Beams' a Reality (Eventually)

    NASA Video Gallery

    Tractor beams -- the ability to trap and move objects using laser light -- are the stuff of science fiction, but a team of NASA scientists has won funding to study the concept for remotely capturin...

  10. Tractor beam in micro-scale

    NASA Astrophysics Data System (ADS)

    Brzobohatý, O.; Karásek, V.; Šiler, M.; Chvátal, L.; Čižmár, T.; Zemánek, P.

    2014-12-01

    Following the Keplerian idea of radiative forces one would intuitively expect that an object illuminated by sunlight radiation or a laser beam is accelerated along the direction of the photon flow. Such radiation pressure forms the basis for the concept of solar sail, or laser acceleration of micro-particles. In contrast, a hypothetical optical field known from the realm of science-fiction as the "tractor" beam attracts the matter from large distances against the beam propagation. We present a geometry of such"tractor" beam in micro-scale and experimentally demonstrate how it acts upon spherical micro-particles of various sizes or optically self-arranged structures of micro-particles.

  11. Three-dimensional analysis of optical forces generated by an active tractor beam using radial polarization.

    PubMed

    Carretero, Luis; Acebal, Pablo; Blaya, Salvador

    2014-02-10

    We theoretically study the three-dimensional behavior of nanoparticles in an active optical conveyor. To do this, we solved the Langevin equation when the forces are generated by a focusing system at the near field. Analytical expressions for the optical forces generated by the optical conveyor were obtained by solving the Richards and Wolf vectorial diffraction integrals in an approximated form when a mask of two annular pupils is illuminated by a radially polarized Hermite-Gauss beam. Trajectories, in both the transverse plane and the longitudinal direction, are analyzed showing that the behavior of the optical conveyor can be optimized by conveniently choosing the configuration of the mask of the two annular pupils (inner and outer radius of the two rings) in order to trap and transport all particles at the focal plane. PMID:24663619

  12. A long-range polarization-controlled optical tractor beam

    NASA Astrophysics Data System (ADS)

    Shvedov, Vladlen; Davoyan, Arthur R.; Hnatovsky, Cyril; Engheta, Nader; Krolikowski, Wieslaw

    2014-11-01

    The laser beam has become an indispensable tool for the controllable manipulation and transport of microscopic objects in biology, physical chemistry and condensed matter physics. In particular, ‘tractor’ laser beams can draw matter towards a laser source and perform, for instance, all-optical remote sampling. Recent advances in lightwave technology have already led to small-scale experimental demonstrations of tractor beams. However, the realization of long-range tractor beams has not gone beyond the realm of theoretical investigations. Here, we demonstrate the stable transfer of gold-coated hollow glass spheres against the power flow of a single inhomogeneously polarized laser beam over tens of centimetres. Additionally, by varying the polarization state of the beam we can stop the spheres or reverse the direction of their motion at will.

  13. Tractor Mechanics: Learning Activity Packages 1-19.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    Learning activity packages are presented for teaching tractor mechanics. The first of two sections deals with miscellaneous tasks and contains learning activity packages on cleaning the tractor and receiving new tractor parts. Section 2 is concerned with maintaining and servicing the electrical system, and it includes the following learning…

  14. Helical tractor beam: analytical solution of Rayleigh particle dynamics.

    PubMed

    Carretero, Luis; Acebal, Pablo; Garcia, Celia; Blaya, Salvador

    2015-08-10

    We analyze particle dynamics in an optical force field generated by helical tractor beams obtained by the interference of a cylindrical beam with a topological charge and a co-propagating temporally de-phased plane wave. We show that, for standard experimental conditions, it is possible to obtain analytical solutions for the trajectories of particles in such force field by using of some approximations. These solutions show that, in contrast to other tractor beams described before, the intensity becomes a key parameter for the control of particle trajectories. Therefore, by tuning the intensity value the particle can describe helical trajectories upstream and downstream, a circular trajectory in a fixed plane, or a linear displacement in the propagation direction. The approximated analytical solutions show good agreement to the corresponding numerical solutions of the exact dynamical differential equations.

  15. Helical tractor beam: analytical solution of Rayleigh particle dynamics.

    PubMed

    Carretero, Luis; Acebal, Pablo; Garcia, Celia; Blaya, Salvador

    2015-08-10

    We analyze particle dynamics in an optical force field generated by helical tractor beams obtained by the interference of a cylindrical beam with a topological charge and a co-propagating temporally de-phased plane wave. We show that, for standard experimental conditions, it is possible to obtain analytical solutions for the trajectories of particles in such force field by using of some approximations. These solutions show that, in contrast to other tractor beams described before, the intensity becomes a key parameter for the control of particle trajectories. Therefore, by tuning the intensity value the particle can describe helical trajectories upstream and downstream, a circular trajectory in a fixed plane, or a linear displacement in the propagation direction. The approximated analytical solutions show good agreement to the corresponding numerical solutions of the exact dynamical differential equations. PMID:26367905

  16. Optimized optical "tractor beam" for core-shell nanoparticles.

    PubMed

    Wang, Neng; Lu, Wanli; Ng, Jack; Lin, Zhifang

    2014-04-15

    It is known that core-shell subwavelength nanoparticles consisting of a dielectric shell and a metallic core can simultaneously support electric and magnetic dipolar resonances, which enhance forward scattering and suppress backward scattering. This creates favorable conditions for optical tractor beam applications. Using the generalized Lorenz-Mie theory and Maxwell stress tensor formulation, we demonstrate how optical pulling forces can be induced and optimized by first-order Bessel beams with appropriate polarization. The transverse stability of the core-shell nanoparticle under ambient damping is also verified by linear stability analysis and dynamical simulation. PMID:24979003

  17. Optical tractor beam with chiral light

    NASA Astrophysics Data System (ADS)

    Fernandes, David E.; Silveirinha, Mário G.

    2015-06-01

    We suggest a novel mechanism to induce the motion of a chiral material body towards an optical source with no optical traps. Our solution is based on the interference between a chiral light beam and its reflection on an opaque mirror. Surprisingly, it is theoretically shown that the electromagnetic response of the material may be tailored in such a way that independent of the specific body location with respect to the mirror, it is always pulled upstream against the photon flow associated with the incoming wave. Moreover, it is proven that by controlling the handedness of the incoming light it may be possible to harness the sign of the optical force, switching from a pulling force to a pushing force.

  18. Tractor Mechanics. Maintaining and Servicing the Engine, Learning Activity Packages 78-89; Lubricating the Tractor, Learning Activity Packages 90-94; Painting the Tractor, Learning Activity Packages 95-96.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This series of learning activity packages focuses on three areas of tractor mechanics: (1) maintaining and servicing the engine, (2) lubricating the tractor, and (3) painting the tractor. Each of the nineteen illustrated learning activity packages follows a typical format: introduction, directions, objectives, learning activities, tools and…

  19. Quantum coherent tractor beam effect for atoms trapped near a nanowaveguide.

    PubMed

    Sadgrove, Mark; Wimberger, Sandro; Nic Chormaic, Síle

    2016-01-01

    We propose several schemes to realize a tractor beam effect for ultracold atoms in the vicinity of a few-mode nanowaveguide. Atoms trapped near the waveguide are transported in a direction opposite to the guided mode propagation direction. We analyse three specific examples for ultracold (23)Na atoms trapped near a specific nanowaveguide (i.e. an optical nanofibre): (i) a conveyor belt-type tractor beam effect, (ii) an accelerator tractor beam effect, and (iii) a quantum coherent tractor beam effect, all of which can effectively pull atoms along the nanofibre toward the light source. This technique provides a new tool for controlling the motion of particles near nanowaveguides with potential applications in the study of particle transport and binding as well as atom interferometry. PMID:27440516

  20. Quantum coherent tractor beam effect for atoms trapped near a nanowaveguide

    PubMed Central

    Sadgrove, Mark; Wimberger, Sandro; Nic Chormaic, Síle

    2016-01-01

    We propose several schemes to realize a tractor beam effect for ultracold atoms in the vicinity of a few-mode nanowaveguide. Atoms trapped near the waveguide are transported in a direction opposite to the guided mode propagation direction. We analyse three specific examples for ultracold 23Na atoms trapped near a specific nanowaveguide (i.e. an optical nanofibre): (i) a conveyor belt-type tractor beam effect, (ii) an accelerator tractor beam effect, and (iii) a quantum coherent tractor beam effect, all of which can effectively pull atoms along the nanofibre toward the light source. This technique provides a new tool for controlling the motion of particles near nanowaveguides with potential applications in the study of particle transport and binding as well as atom interferometry. PMID:27440516

  1. Quantum coherent tractor beam effect for atoms trapped near a nanowaveguide.

    PubMed

    Sadgrove, Mark; Wimberger, Sandro; Nic Chormaic, Síle

    2016-07-21

    We propose several schemes to realize a tractor beam effect for ultracold atoms in the vicinity of a few-mode nanowaveguide. Atoms trapped near the waveguide are transported in a direction opposite to the guided mode propagation direction. We analyse three specific examples for ultracold (23)Na atoms trapped near a specific nanowaveguide (i.e. an optical nanofibre): (i) a conveyor belt-type tractor beam effect, (ii) an accelerator tractor beam effect, and (iii) a quantum coherent tractor beam effect, all of which can effectively pull atoms along the nanofibre toward the light source. This technique provides a new tool for controlling the motion of particles near nanowaveguides with potential applications in the study of particle transport and binding as well as atom interferometry.

  2. Quantum coherent tractor beam effect for atoms trapped near a nanowaveguide

    NASA Astrophysics Data System (ADS)

    Sadgrove, Mark; Wimberger, Sandro; Nic Chormaic, Síle

    2016-07-01

    We propose several schemes to realize a tractor beam effect for ultracold atoms in the vicinity of a few-mode nanowaveguide. Atoms trapped near the waveguide are transported in a direction opposite to the guided mode propagation direction. We analyse three specific examples for ultracold 23Na atoms trapped near a specific nanowaveguide (i.e. an optical nanofibre): (i) a conveyor belt-type tractor beam effect, (ii) an accelerator tractor beam effect, and (iii) a quantum coherent tractor beam effect, all of which can effectively pull atoms along the nanofibre toward the light source. This technique provides a new tool for controlling the motion of particles near nanowaveguides with potential applications in the study of particle transport and binding as well as atom interferometry.

  3. Off-axial acoustic radiation force of repulsor and tractor bessel beams on a sphere.

    PubMed

    Silva, Glauber T; Lopes, J Henrique; Mitri, Farid G

    2013-06-01

    Acoustic Bessel beams are known to produce an axial radiation force on a sphere centered on the beam axis (on-axial configuration) that exhibits both repulsor and tractor behaviors. The repulsor and the tractor forces are oriented along the beam's direction of propagation and opposite to it, respectively. The behavior of the acoustic radiation force generated by Bessel beams when the sphere lies outside the beam's axis (off-axial configuration) is unknown. Using the 3-D radiation force formulas given in terms of the partial wave expansion coefficients for the incident and scattered waves, both axial and transverse components of the force exerted on a silicone- oil sphere are obtained for a zero- and a first-order Bessel vortex beam. As the sphere departs from the beam's axis, the tractor force becomes weaker. Moreover, the behavior of the transverse radiation force field may vary with the sphere's size factor ka (where k is the wavenumber and a is the sphere radius). Both stable and unstable equilibrium regions around the beam's axis are found, depending on ka values. These results are particularly important for the design of acoustical tractor beam devices operating with Bessel beams. PMID:25004483

  4. Optical pulling force on a magneto-dielectric Rayleigh sphere in Bessel tractor polarized beams

    NASA Astrophysics Data System (ADS)

    Mitri, F. G.; Li, R. X.; Yang, R. P.; Guo, L. X.; Ding, C. Y.

    2016-11-01

    The optical radiation force induced by Bessel (vortex) beams on a magneto-dielectric subwavelength sphere is investigated with particular emphasis on the beam polarization and order l (or topological charge). The analysis is focused on identifying the regions and some of the conditions to achieve retrograde motion of the sphere centered on the axis of wave propagation of the incident beam, or shifted off-axially. Exact non-paraxial analytical solutions are established, and computations for linear, circular, radial, azimuthal and mixed polarizations of the individual plane wave components forming the Bessel (vortex) beams by means of the angular spectrum decomposition method (ASDM) illustrate the theory with particular emphasis on the tractor (i.e. reversal) behavior of the force. This effect results in the pulling of the magneto-dielectric sphere against the forward linear momentum density flux associated with the incoming waves. Should some conditions related to the choice of the beam parameters as well as the permittivity and permeability of the sphere be met, the optical force vanishes and reverses sign. Moreover, the beam polarization is shown to affect differently the axial negative pulling force for either the zeroth- or the first-order Bessel beam. When the sphere is centered on the beam‧s axis, the axial force component is always negative for the zeroth-order Bessel beam except for the radial and azimuthal polarization configurations. Nonetheless, for the first-order Bessel beam, the axial force is negative for the radial polarization case only. Additional tractor beam effects arise when the sphere departs from the center of the beam. It is also demonstrated that the tractor beam effect arises from the force component originating from the cross-interaction between the electric and magnetic dipoles. Potential applications are in particle manipulation, optical levitation, tractor beam tweezers, and other emergent technologies using polarized Bessel beams on

  5. Acoustical pulling force on rigid spheroids in single Bessel vortex tractor beams

    NASA Astrophysics Data System (ADS)

    Mitri, F. G.

    2015-11-01

    The theoretical formalism for acoustical Bessel vortex (helicoidal) tractor beams and results presented here are the first to demonstrate the emergence of a pulling force of attraction on non-spherical oblate and prolate rigid spheroidal particles centered on the beam's axis of wave propagation. Numerical predictions for the axial acoustic radiation force illustrate the theory with particular emphasis on the aspect ratio of the spheroid, the half-cone angle and order of the beam, as well as the dimensionless size parameter. It is demonstrated here that the Bessel vortex beam parameters may be tailored in such a way that the spheroid is pulled against the forward linear momentum density flux associated with the incoming waves. Those results potentially suggest the use of Bessel vortex beams in the development of emergent technologies for non-contact remote sampling and particle characterization.

  6. Propulsion Systems Integration for a `Tractor Beam' Mercury Lightcraft: Liftoff Engine

    NASA Astrophysics Data System (ADS)

    Myrabo, L. N.

    2003-05-01

    Described herein is the concept and propulsion systems integration for a revolutionary beam-propelled shuttle called the ``Mercury'' lightcraft - emphasizing the liftoff engine mode. This one-person, ultra-energetic vehicle is designed to ride `tractor beams' into space, transmitted from a future network of satellite solar power stations. The objective is to create a safe, very low cost (e.g., 1000X below chemical rockets) space transportation system for human life, one that is completely `green' and independent of Earth's limited fossil fuel reserves. The lightcraft's airbreathing combined-cycle engine operates in a rotary pulsed detonation mode PDE for lift-offs and landings; at hypersonic speeds it transitions into a magnetohydrodynamic (MHD) slipstream accelerator mode. For the latter, the transatmospheric flight path is momentarily transformed into an extremely long, electromagnetic ``mass-driver'' channel with an effective `fuel' specific impulse in the range of 6000 to 16,000 seconds. These future single-stage-to-orbit, highly-reusuable vehicles will ride ``Highways of Light,'' accelerating at 3 Gs into space, with their throttles just barely beyond `idle' power.

  7. Tractor Mechanics: Maintaining and Servicing the Fuel System. Learning Activity Packages 20-33.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    Learning activity packages are presented for instruction in tractor mechanics. The packages deal with the duties involved in maintaining the fuel system. The following fourteen learning activity packages are included: servicing fuel and air filters, servicing fuel tanks and lines, adjusting a carburetor, servicing a carburetor, servicing the…

  8. Tractor Mechanics. Maintaining and Servicing the Cooling System, Learning Activity Packages 34-40; Maintaining and Servicing Hydraulic Systems, Learning Activity Packages 41-48.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This series of learning activity packages focuses on two areas of tractor mechanics: (1) maintaining and servicing the cooling system and (2) maintaining and servicing hydraulic systems. Each of the fifteen illustrated learning activity packages follows a typical format: introduction, directions, objectives, learning activities, tools and…

  9. Enhanced fuel efficiency on tractor-trailers using synthetic jet-based active flow control

    NASA Astrophysics Data System (ADS)

    Amitay, Michael; Menicovich, David; Gallardo, Daniele

    2016-04-01

    The application of piezo-electrically-driven synthetic-jet-based active flow control to reduce drag on tractor-trailers was explored experimentally in wind tunnel testing as well as full-scale road tests. Aerodynamic drag accounts for more than 50% of the usable energy at highway speeds, a problem that applies primarily to trailer trucks. Therefore, a reduction in aerodynamic drag results in large saving of fuel and reduction in CO2 emissions. The active flow control technique that is being used relies on a modular system comprised of distributed, small, highly efficient actuators. These actuators, called synthetic jets, are jets that are synthesized at the edge of an orifice by a periodic motion of a piezoelectric diaphragm(s) mounted on one (or more) walls of a sealed cavity. The synthetic jet is zero net mass flux (ZNMF), but it allows momentum transfer to flow. It is typically driven near diaphragm and/or cavity resonance, and therefore, small electric input [O(10W)] is required. Another advantage of this actuator is that no plumbing is required. The system doesn't require changes to the body of the truck, can be easily reconfigured to various types of vehicles, and consumes small amounts of electrical power from the existing electrical system of the truck. Preliminary wind tunnel results showed up to 18% reduction in fuel consumption, whereas road tests also showed very promising results.

  10. Miniature Tractor Pull Helps Teach Mechanical Power Transmission.

    ERIC Educational Resources Information Center

    Waggoner, Todd C.

    1996-01-01

    A miniature tractor pull was developed as a high school activity, enabling students to assess a tractor's pulling capabilities and determine subsequent horsepower. The activity takes the textbook concept of horsepower and makes it come alive. (JOW)

  11. Active Beam Spectroscopy

    NASA Astrophysics Data System (ADS)

    von Hellermann, M. G.; Delabie, E.; Jaspers, R. J. E.; Biel, W.; Marchuk, O.; Summers, H. P.; Whiteford, A.; Giroud, C.; Hawkes, N. C.; Zastrow, K. D.

    2008-03-01

    Charge eXchange Recombination Spectroscopy (CXRS) plays a pivotal role in the diagnostics of hot fusion plasmas and is implemented currently in most of the operating devices. In the present report the main features of CXRS are summarized and supporting software packages encompassing "Spectral Analysis Code CXSFIT", "Charge Exchange Analysis Package CHEAP", and finally "Forward Prediction of Spectral Features" are described. Beam Emission Spectroscopy (BES) is proposed as indispensable cross-calibration tool for absolute local impurity density measurements and also for the continuous monitoring of the neutral beam power deposition profile. Finally, a full exploitation of the `Motional Stark Effect' pattern is proposed to deduce local pitch angles, total magnetic fields and possibly radial electric fields. For the proposed active beam spectroscopy diagnostic on ITER comprehensive performance studies have been carried out. Estimates of expected spectral signal-to-noise ratios are based on atomic modelling of neutral beam stopping and emissivities for CXRS, BES and background continuum radiation as well as extrapolations from present CXRS diagnostic systems on JET, Tore Supra, TEXTOR and ASDEX-UG. Supplementary to thermal features a further promising application of CXRS has been proposed recently for ITER, that is a study of slowing-down alpha particles in the energy range up to 2 MeV making use of the 100 keV/amu DNB (Diagnostic Neutral Beam) and the 500 keV/amu HNB (Heating Neutral Beam). Synthetic Fast Ion Slowing-Down spectra are evaluated in terms of source rates and slowing-down parameters

  12. Keys to Successful Tractor Maintenance Units.

    ERIC Educational Resources Information Center

    Doerr, William A.

    1979-01-01

    To prevent problems with teaching plans, supplement class instruction, and stimulate use of the operator's manual, the teacher can use a series of leaflets. The first leaflet describes the activities and what is expected of the tractor operator's manual. (LRA)

  13. Miniature pipe crawler tractor

    SciTech Connect

    McKay, M.D.; Anderson, M.O.; Ferrante, T.A.; Willis, W.D.

    2000-03-14

    A pipe crawler tractor may comprise a half tractor assembly having a first base drive wheel, a second base drive wheel, and a top drive wheel. The drive wheels are mounted in spaced-apart relation so that the top drive wheel is positioned between the first and second base drive wheels. The mounting arrangement is also such that the first and second base drive wheels contact the inside surface of the pipe at respective first and second positions and so that the top drive wheel contacts the inside surface of the pipe at a third position, the third position being substantially diametrically opposed to the first and second positions. A control system connected to the half tractor assembly controls the rotation of the first base wheel, the second base wheel, and the top drive wheel to move the half tractor assembly within the pipe.

  14. Miniature pipe crawler tractor

    DOEpatents

    McKay, Mark D.; Anderson, Matthew O.; Ferrante, Todd A.; Willis, W. David

    2000-01-01

    A pipe crawler tractor may comprise a half tractor assembly having a first base drive wheel, a second base drive wheel, and a top drive wheel. The drive wheels are mounted in spaced-apart relation so that the top drive wheel is positioned between the first and second base drive wheels. The mounting arrangement is also such that the first and second base drive wheels contact the inside surface of the pipe at respective first and second positions and so that the top drive wheel contacts the inside surface of the pipe at a third position, the third position being substantially diametrically opposed to the first and second positions. A control system connected to the half tractor assembly controls the rotation of the first base wheel, the second base wheel, and the top drive wheel to move the half tractor assembly within the pipe.

  15. Active beam spectroscopy for ITER

    NASA Astrophysics Data System (ADS)

    von Hellermann, M. G.; Barnsley, R.; Biel, W.; Delabie, E.; Hawkes, N.; Jaspers, R.; Johnson, D.; Klinkhamer, F.; Lischtschenko, O.; Marchuk, O.; Schunke, B.; Singh, M. J.; Snijders, B.; Summers, H. P.; Thomas, D.; Tugarinov, S.; Vasu, P.

    2010-11-01

    Since the first feasibility studies of active beam spectroscopy on ITER in 1995 the proposed diagnostic has developed into a well advanced and mature system. Substantial progress has been achieved on the physics side including comprehensive performance studies based on an advanced predictive code, which simulates active and passive features of the expected spectral ranges. The simulation has enabled detailed specifications for an optimized instrumentation and has helped to specify suitable diagnostic neutral beam parameters. Four ITER partners share presently the task of developing a suite of ITER active beam diagnostics, which make use of the two 0.5 MeV/amu 18 MW heating neutral beams and a dedicated 0.1 MeV/amu, 3.6 MW diagnostic neutral beam. The IN ITER team is responsible for the DNB development and also for beam physics related aspects of the diagnostic. The RF will be responsible for edge CXRS system covering the outer region of the plasma (1> r/ a>0.4) using an equatorial observation port, and the EU will develop the core CXRS system for the very core (0< r/ a<0.7) using a top observation port. Thus optimum radial resolution is ensured for each system with better than a/30 resolution. Finally, the US will develop a dedicated MSE system making use of the HNBs and two equatorial ports. With appropriate modification, these systems could also potentially provide information on alpha particle slowing-down features. . On the engineering side, comprehensive preparations were made involving the development of an observation periscope, a neutron labyrinth optical system and design studies for remote maintenance including the exchange of the first mirror assembly, a critical issue for the operation of the CXRS diagnostic in the harsh ITER environment. Additionally, an essential change of the orientation of the DNB injection angle and specification of suitable blanket aperture has been made to avoid trapped particle damage to the first wall.

  16. Tractor Operation and Daily Care.

    ERIC Educational Resources Information Center

    Fore, J. M.; And Others

    Written for the tractor operator, the manual describes, with the aid of colored illustrations and diagrams, the tasks involved in the proper operation and daily maintenance of tractors. It offers explanations for the desirability of the various servicing and adjustment operations, as well as guidelines for tractor operation and safety. The…

  17. Tractor & Machinery Safety. 1984 Revision.

    ERIC Educational Resources Information Center

    Montana State Office of Public Instruction, Helena. Dept. of Vocational Education Services.

    This curriculum guide is intended for use in teaching an instructional unit in tractor and machinery safety that is geared toward college freshmen. Addressed in the individual lessons of the unit are the following topics: understanding the importance of safe and efficient tractor operation, understanding the characteristics of tractors, preparing…

  18. Electrostatic Tractor Analysis for GEO Debris Remediation

    NASA Astrophysics Data System (ADS)

    Hogan, Erik A.

    The high value of operating in the geostationary ring, coupled with increasing numbers of orbital debris, highlights the need for GEO debris remediation techniques. One recent proposed technique for GEO debris mitigation is the electrostatic tractor. Here, a tug vehicle approaches a target debris object and emits a focused electron beam onto it. This results in a negative charge on the debris, and a positive charge on the tug vehicle. Due to the near proximity of the highly charged objects (20 meters or less) an attractive electrostatic force on the order of milliNewtons results. This electrostatic force is used in conjunction with low thrusting by the tug vehicle to tow the debris object into a disposal orbit 200-300 kilometers above the GEO belt. During the tugging period, the charged relative motion between tug and deputy is stabilized through a feedback control law. This is accomplished using a novel relative motion description that isolates separation distance from the relative orientation. The equations of motion for the relative motion description are derived from the Clohessy-Wiltshire equations, assuming the debris object is in a nearly circular orbit. Lyapunov stability theory is used to derive an asymptotically stable control law for the tug thrusters during the towing period. The control law requires an estimate of the electrostatic force magnitude, and the impacts of improperly modeled charging on control response are determined. If the electrostatic force is under-predicted too severely, a collision may result. A bound on the control gains is determined to prevent such a collision. Expected reorbiting performance levels achievable with the electrostatic tractor are computed. An open-loop analytical performance study is performed where variational equations are used to predict how much general orbital elements may be changed using the electrostatic tractor over one orbital period for a towed object at geosynchronous altitude. In contrast to earlier

  19. Plans for Learning Stations. Tractor Mechanics.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This shop guide gives graphic illustration of twenty-eight learning stations in a tractor mechanics shop, at each of which a specific learning activity occurs. The authors suggest that each station (most of them constructed of plywood or sheet metal and angle iron) be self-contained, having its own appropriate tools, supplies, parts, and set of…

  20. Vegetable oils for tractors

    SciTech Connect

    Moroney, M.

    1981-11-14

    Preliminary tests by the Agricultural Institute, show that tractors can be run on a 50:50 rape oil-diesel mixture or on pure rape oil. In fact, engine power actually increased slightly with the 50:50 blend but decreased fractionally with pure rape oil. Research at the North Dakota State University on using sunflower oil as an alternative to diesel fuel is also noted.

  1. Tractor Safety. Unit A-9.

    ERIC Educational Resources Information Center

    Luft, Vernon D.; Backlund, Paul

    This document is a teacher's guide for a unit in tractor and machinery safety for college freshmen. It is intended to be used for 10 hours of instruction for freshmen who are intending to work on or around machinery. Safety hazards directly and indirectly related to many types of machinery are covered in addition to tractors. The objectives of the…

  2. Tractor Mechanics. Maintaining and Servicing the Power Train, Learning Activity Packages 49-53; Maintaining and Servicing the Clutch, Learning Activity Packages 54-59; Maintaining and Servicing the Transmission and Differential, Learning Activity Packages 60-68; Maintaining and Servicing the Final Drive, Learning Activity Packages 69-77.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This series of learning activity packages focuses on four areas of tractor mechanics: (1) maintaining and servicing the power train, (2) maintaining and servicing the clutch, (3) maintaining and servicing the transmission and differential, and (4) maintaining and servicing the final drive. Each of the twenty-nine illustrated learning activity…

  3. Mission Designs for Demonstrating Gravity Tractor Asteroid Deflection

    NASA Astrophysics Data System (ADS)

    Busch, M.; Faber, N.; Eggl, S.; Morrison, D.; Clark, A.; Frost, C.; Jaroux, B. A.; Khetawat, V.

    2015-12-01

    Gravity tractor asteroid deflection relies on the gravitational attraction between the target and a nearby spacecraft; using low-thrust propulsion to change the target's trajectory slowly but continuously. Our team, based at the NASA Ames Mission Design Center, prepared designs for a Gravity Tractor Demonstration Mission (GTDM) for the European Commission's NEOShield initiative. We found five asteroids with well-known orbits and opportunities for efficient stand-alone demonstrations in the 2020s. We selected one object, 2000 FJ10, for a detailed design analysis. Our GTDM design has a 4 kW solar-electric propulsion system and launch mass of 1150 kg. For a nominal asteroid mass of 3 x 109 kg and diameter 150 m, and a hovering altitude 125 m above the asteroid's surface, GTDM would change FJ10's semi-major axis by 10 km over 2 years. To measure the deflection clearly and to permit safe hovering by the spacecraft, several months of survey and characterization are required prior to the active tractoring phase of the mission. Accurate tracking is also required after the tractoring phase, to ensure that the asteroid has indeed been deflected as intended. The GTDM design includes both spacecraft and Earth-based observations of FJ10 to verify the deflection. The estimated cost of GTDM is $280 million. Trajectory analysis for GTDM confirmed that the outcome of a deflection of any asteroid depends on when that deflection is performed. Compared to kinetic impactor deflection, the gradual deflection from a gravity tractor produces comparable results for a given total momentum transfer. However, a gravity tractor can have greater flexibility in the direction in which the target asteroid can be deflected. Asteroid deflection scenarios must be modeled carefully on a case-to-case basis. We will review implications of the results of the GTDM study to other proposed gravity tractor demonstrations, such as that included in NASA's Asteroid Redirect Mission.

  4. Tractor accidents in Swedish traffic.

    PubMed

    Pinzke, Stefan; Nilsson, Kerstin; Lundqvist, Peter

    2012-01-01

    The objective of this study is to reach a better understanding of accidents on Swedish roads involving tractors and to suggest ways of preventing them. In an earlier study we analyzed police-reported fatal accidents and accidents that led to physical injuries from 1992 to 2005. During each year of this period, tractors were involved in 128 traffic accidents on average, an average of 7 people were killed, 44 sustained serious injuries, and 143 sustained slight injuries. The number of fatalities in these tractor accidents was about 1.3% of all deaths in traffic accidents in Sweden. Cars were most often involved in the tractor accidents (58%) and 15% were single vehicle accidents. The mean age of the tractor driver involved was 39.8 years and young drivers (15-24 years) were overrepresented (30%). We are now increasing the data collected with the years 2006-2010 in order to study the changes in the number of accidents. Special attention will be given to the younger drivers and to single vehicle accidents. Based on the results we aim to develop suggestions for reducing road accidents, e.g. including measures for making farm vehicles more visible and improvement of the training provided at driving schools. PMID:22317543

  5. ROPS deficiency of gray-market tractors.

    PubMed

    Myers, M L; Purschwitz, M A

    2012-04-01

    Many used tractors that are imported from Japan are adding to the current national inventory in the U.S. and Canada of farm tractors that lack a rollover protective structure (ROPS). Gray-market tractors are built for use by the manufacturer for a certain country but are imported against the manufacture's wishes to a second country for use there, usually as a used tractor. Gray-market tractors may lack ROPS and seatbelts, depending on the date of manufacturer. The objective of this investigation is to describe the gray market for tractors imported from Japan into the U.S. and the policy implications regarding the hazards associated with these imports. Operator manuals and warning labels are typically not written in English. Foreign manufacturers that market tractors in the U.S. have established a variety of disincentives for the importation of gray-market tractors, including issuing warnings, not servicing or providing parts for these tractors, and banning their importation through actions by the U.S. International Trade Commission. Nonetheless, a U.S. market has developed that imports and provides services and parts for gray-market tractors, and some companies provide certified ROPS on the tractors that they sell. A product safety perspective and related policies are presented as an approach to ensuring that these imports are equipped with ROPS and seatbelts. PMID:22655522

  6. Impacts of tug and debris sizes on electrostatic tractor charging performance

    NASA Astrophysics Data System (ADS)

    Hogan, Erik A.; Schaub, Hanspeter

    2015-01-01

    Active debris removal techniques enable relocating noncooperative geosynchronous (GEO) debris objects into graveyard orbits. One proposed method is the electrostatic tractor concept. Here a tug vehicle approaches a target debris object and emits an electron beam onto the debris. The charging that results yields an attractive electrostatic force that is used to tow the debris object into a new orbit. In this study, the impacts of relative sizing between tug and debris on the efficacy of this charge transfer process are considered. By applying a charging model and incorporating nominal, quiet GEO space weather conditions, limitations on the size ratio that preclude charge transfer are identified for different levels of beam energy. The resulting electrostatic forces and impacts on reorbiting performance are studied. The results indicate that a larger tug vehicle will enable the tugging of a broader range of debris sizes, and that the tug size should be roughly as large as the expected debris size.

  7. Space Weather Influence on Relative Motion Control using the Touchless Electrostatic Tractor

    NASA Astrophysics Data System (ADS)

    Hogan, Erik A.; Schaub, Hanspeter

    2016-09-01

    With recent interest in the use of electrostatic forces for contactless tugging and attitude control of noncooperative objects for orbital servicing and active debris mitigation, the need for a method of remote charge control arises. In this paper, the use of a directed electron beam for remote charge control is considered in conjunction with the relative motion control. A tug vehicle emits an electron beam onto a deputy object, charging it negatively. At the same time, the tug is charged positively due to beam emission, resulting in an attractive electrostatic force. The relative position feedback control between the tug and the passive debris object is studied subject to the charging being created through an electron beam. Employing the nominal variations of the GEO space weather conditions across longitude slots, two electrostatic tugging strategies are considered. First, the electron beam current is adjusted throughout the orbit in order to maximize this resulting electrostatic force. This open-loop control strategy compensates for changes in the nominally expected local space weather environment in the GEO region to adjust for fluctuations in the local plasma return currents. Second, the performance impact of using a fixed electron beam current on the electrostatic tractor is studied if the same natural space weather variations are assumed. The fixed electron beam current shows a minor performance penalty (<5 %) while providing a much simpler implementation that does not require any knowledge of local space weather conditions.

  8. Tractor Transmissions. A Teaching Reference.

    ERIC Educational Resources Information Center

    American Association for Agricultural Engineering and Vocational Agriculture, Athens, GA.

    The manual was developed as a reference for teaching students about transmissions in farm tractors. The manual is divided into five sections: (1) transmission history, (2) gears and bearings in transmission, (3) sliding-gear transmissions, (4) planetary gearing, and (5) glossary. The working principles of the sliding-gear transmission, the most…

  9. Microhole Drilling Tractor Technology Development

    SciTech Connect

    Western Well Tool

    2007-07-09

    In an effort to increase the U.S. energy reserves and lower costs for finding and retrieving oil, the USDOE created a solicitation to encourage industry to focus on means to operate in small diameter well-Microhole. Partially in response to this solicitation and because Western Well Tool's (WWT) corporate objective to develop small diameter coiled tubing drilling tractor, WWT responded to and was awarded a contract to design, prototype, shop test, and field demonstrate a Microhole Drilling Tractor (MDT). The benefit to the oil industry and the US consumer from the project is that with the MDT's ability to facilitate Coiled Tubing drilled wells to be 1000-3000 feet longer horizontally, US brown fields can be more efficiently exploited resulting in fewer wells, less environmental impact, greater and faster oil recovery, and lower drilling costs. Shortly after award of the contract, WWT was approached by a major oil company that strongly indicated that the specified size of a tractor of 3.0 inches diameter was inappropriate and that immediate applications for a 3.38-inch diameter tractor would substantially increase the usefulness of the tool to the oil industry. Based on this along with an understanding with the oil company to use the tractor in multiple field applications, WWT applied for and was granted a no-cost change-of-scope contract amendment to design, manufacture, assemble, shop test and field demonstrate a prototype a 3.38 inch diameter MDT. Utilizing existing WWT tractor technology and conforming to an industry developed specification for the tool, the Microhole Drilling Tractor was designed. Specific features of the MDT that increase it usefulness are: (1) Operation on differential pressure of the drilling fluid, (2) On-Off Capability, (3) Patented unique gripping elements (4) High strength and flexibility, (5) Compatibility to existing Coiled Tubing drilling equipment and operations. The ability to power the MDT with drilling fluid results in a highly

  10. Conformal superalgebras via tractor calculus

    NASA Astrophysics Data System (ADS)

    Lischewski, Andree

    2015-01-01

    We use the manifestly conformally invariant description of a Lorentzian conformal structure in terms of a parabolic Cartan geometry in order to introduce a superalgebra structure on the space of twistor spinors and normal conformal vector fields formulated in purely algebraic terms on parallel sections in tractor bundles. Via a fixed metric in the conformal class, one reproduces a conformal superalgebra structure that has been considered in the literature before. The tractor approach, however, makes clear that the failure of this object to be a Lie superalgebra in certain cases is due to purely algebraic identities on the spinor module and to special properties of the conformal holonomy representation. Moreover, it naturally generalizes to higher signatures. This yields new formulas for constructing new twistor spinors and higher order normal conformal Killing forms out of existing ones, generalizing the well-known spinorial Lie derivative. Moreover, we derive restrictions on the possible dimension of the space of twistor spinors in any metric signature.

  11. Optical Pulling Force and Tractor Beams

    NASA Astrophysics Data System (ADS)

    Paul, Nayan Kumar

    Light-matter interaction has been an interesting subject of intense analytical and experimental research since the formulation of Maxwell's electromagnetic wave theory. Optical forces exerted on particles excited by incident light waves have been studied for the last few decades. The interaction of light with materials gives rise to light scattering from the particle in the form of energy. The divergence of the Maxwell stress tensor provides a good approximation of the total optical forces on a particle. The divergence of the stress tensor is mathematically equal to the time average Lorentz force since [special characters omitted]. Others have claimed that the stress tensor is "fraught with danger," but it is a matter of application. The stress tensor approach is computationally simpler since application of the divergence theorem allows for a reduction of dimension in the integration. For example, you can either integrate the force density over the volume of an object (3-D), or integrate the divergence of the stress tensor on a surface (2-D) enclosing the volume. It gives a straightforward prediction of the total optical forces on a particle, but may be challenging in the case of multiple particles or for larger particles. The Rayleigh approximation estimates the radiation pressure on small particles in the propagation direction of light, but may be inappropriate for larger particles in comparison to the wavelength of the incident light waves. Light waves exert radiation pressure on a particle and pushes it away from the light source toward the direction of propagation. It is shown that plane waves propagating in a rectangular waveguide not only push a passive particle toward the propagation direction, but also pull it toward the light source. The particle remains trapped in the transverse direction of the rectangular waveguide. The Lorentz force and the Rayleigh approximation are applied to calculate the total force on the particle. The push-pull phenomenon depends on the frequency of the incident light wave. Optical pulling of a spherical Rayleigh particle along the surface of a dielectric slab waveguide is also shown. The particle is trapped in the transverse direction near the surface of the slab and can be pushed or pulled in the longitudinal direction along the surface of the slab. The pushing and pulling forces switch near the switching frequency of the slab. The manipulation of a small particle on the surface of a material due to the control of standing waves generated on the surface is presented. Evanescent waves pull the particle toward the surface of the material and the particle is trapped by the standing waves. Two mirrors are used and the adjustments of the mirrors allows precise and arbitrary manipulation of the trapped particle on the surface of the material. The magnitude of the pulling force on the particle depends on the angle of incident of light waves.

  12. Simplified overturn stability monitoring of agricultural tractors.

    PubMed

    Nichol, C I; Sommer, H J; Murphy, D J

    2005-02-01

    Agricultural tractors are the most common source of farm work fatalities in the U.S., with overturns the most common type of incident. For the year 2001, there were 15 tractor-related fatalities in Pennsylvania, 9 of which were due to tractor rollover. A new device using low-cost sensors and microcomputers was developed around a simplified mathematical model of an agricultural tractor to inform the operator of potential tractor instability. This device communicates the current rollover potential, along with a recent history of rollover potential, to the operator of the tractor via a simple bar-graph display. The device uses a single-chip accelerometer to sense the current rollover potential and a small microprocessor to analyze the accelerometer data, compensate for variations due to temperature, and then send this information to a visual display. The use of these low-cost "off the shelf" components enabled the fabrication of a very inexpensive sensor system. Because agricultural tractors have a long service life, it was important to make the device low cost and flexible. This could enable it to be sold as an aftermarket add-on for a variety of tractor models. The device is also capable of interfacing with newer on-board tractor systems via a CAN bus to make it more attractive to tractor manufacturers who may want to incorporate this device into new models. Work is continuing on the development of an improved display to inform the tractor operator of possible instability, including display ergonomic studies, investigation of threshold levels for alerting an operator of potential instability, and investigation into audible warning signals.

  13. Active Beam Shaping System and Method Using Sequential Deformable Mirrors

    NASA Technical Reports Server (NTRS)

    Norman, Colin A. (Inventor); Pueyo, Laurent A. (Inventor)

    2015-01-01

    An active optical beam shaping system includes a first deformable mirror arranged to at least partially intercept an entrance beam of light and to provide a first reflected beam of light, a second deformable mirror arranged to at least partially intercept the first reflected beam of light from the first deformable mirror and to provide a second reflected beam of light, and a signal processing and control system configured to communicate with the first and second deformable mirrors. The first deformable mirror, the second deformable mirror and the signal processing and control system together provide a large amplitude light modulation range to provide an actively shaped optical beam.

  14. 49 CFR 523.9 - Truck tractors.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 6 2011-10-01 2011-10-01 false Truck tractors. 523.9 Section 523.9 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION... this part are considered as any truck tractor as defined in 49 CFR part 571 having a GVWR above...

  15. New method of space debris cleaning based on light negative force: tractor laser

    NASA Astrophysics Data System (ADS)

    Sun, Qiongge; Gao, Long; Li, Chen

    2016-01-01

    This paper presents a new way of space debris removal and protection, that is, using tractor laser, which based on light negative force, to achieve space debris cleaning and shielded. Tractor laser is traceable from the theory of optical tweezers, accompanied with non-diffraction beam. These kind of optical beams have the force named negative force pointing to optical source, this will bring the object along the trajectory of laser beam moving to the optical source. The negative force leads to the new method to convey and sampling the space micro-objects. In this paper, the application of tractor laser in the space debris collection and protection of 1cm is studied. The application of the several tractor beams in the space debris and sample collection is discussed. The proposed method can reduce the requirements of the laser to the satellite platform, and realize the collection of space debris, make the establishment of the space garbage station possible, and help to study the spatial non contact sample transmission and reduce the risk of space missions.

  16. Comparative analysis into the tractor-trailer braking dynamics: tractor with single axle brakes, tractor with all wheel brakes

    NASA Astrophysics Data System (ADS)

    Nastasoiu, Mircea; Ispas, Nicolae

    2014-06-01

    The paper elaborates a mathematical model in order to conduct a study into the dynamics of tractor-trailer systems during braking. The braking dynamics is analyzed by considering two versions for the braking system: 1) braking applied on the rear axle and 2) braking applied on all four wheels. In both versions the trailer is braked on all wheels. The mathematical model enables us to determine and graphically illustrate the evolution of the following parameters: braking deceleration, braking speed and the distance traveled by the tractor during braking. The mathematical model elaborated is applied on a tractor-trailer system completing transportation works.

  17. Active control of buckling of flexible beams

    NASA Technical Reports Server (NTRS)

    Baz, A.; Tampe, L.

    1989-01-01

    The feasibility of using the rapidly growing technology of the shape memory alloys actuators in actively controlling the buckling of large flexible structures is investigated. The need for such buckling control systems is becoming inevitable as the design trends of large space structures have resulted in the use of structural members that are long, slender, and very flexible. In addition, as these truss members are subjected mainly to longitudinal loading they become susceptible to structural instabilities due to buckling. Proper control of such instabilities is essential to the effective performance of the structures as stable platforms for communication and observation. Mathematical models are presented that simulate the dynamic characteristics of the shape memory actuator, the compressive structural members, and the associated active control system. A closed-loop computer-controlled system is designed, based on the developed mathematical models, and implemented to control the buckling of simple beams. The performance of the computer-controlled system is evaluated experimentally and compared with the theoretical predictions to validate the developed models. The obtained results emphasize the importance of buckling control and suggest the potential of the shape memory actuators as attractive means for controlling structural deformation in a simple and reliable way.

  18. High-speed optimal steering of a tractor-semitrailer

    NASA Astrophysics Data System (ADS)

    Cheng, Caizhen; Roebuck, Richard; Odhams, Andrew; Cebon, David

    2011-04-01

    A high-speed optimal trailer steering controller for a tractor-semitrailer is discussed. A linear model of a tractor-semitrailer with steered trailer axles is described, and an optimal trailer steering controller is introduced. A path-following controller is derived to minimise the path-tracking error in steady-state manoeuvres using active trailer steering. A roll stability controller is introduced by adding the lateral acceleration of trailer centre of gravity as another objective in the steering controller, so as to improve roll stability in transient manoeuvres. A strategy to switch between these two control modes is demonstrated. Simulation results show that the steering controller can ensure good path tracking of articulated vehicles in steady-state manoeuvres and improve roll stability significantly in transient manoeuvres, while maintaining the path-tracking deviation within an acceptable range. Tests with an experimental tractor-semitrailer equipped with a high-bandwidth active steering system validate the controller design and simulation results. The roll stability controller reduces the measured rearward amplification by 27%.

  19. Analysis of tractor-related deaths.

    PubMed

    Erkol, Zerrin; Buken, Bora; Hekimoglu, Yavuz; Erkol, Hayri; Ince, Haluk; Erzengin, Omer Utku

    2013-01-01

    The aim of the study was to evaluate the properties of tractor-related death cases and discuss the precautions in order to prevent such events. For this aim, reports made between 2006 and 2009 by the First Specialty Board of Council of Forensic Medicine (FSBCFM), Turkey, were evaluated retrospectively. Forty-one tractor-related death cases were included in this study. Thirty-five (85.4%) of the cases were male. The mean age was 42.52 ± 25.1 (with a range between 1 and 84 years old). The average time interval between the incident and death was 13.76 ± 33.53 days (range: 0-176 days) and 20 (48.8%) cases died on the incident spot or during transportation to the hospital. Among the cases, 34.1% (n = 14) were drivers, whereas 39.0% (n = 16) were passengers and the remaining were pedestrians (26.9%, n = 11). The accident was caused by the tractor rolling over in 34.1%, the victim being run over in 22.0%, and the victim falling from the tractor or trailer in 22.0% of the cases. Most of the events (56.1%) occurred on the road. In conclusion, tractors must not be used as a transportation vehicle for passengers. Periodic training of drivers can be useful for reducing tractor-related accidents. PMID:23540299

  20. Operator assessment of tractor roll angle with and without a tractor stability visual feedback device.

    PubMed

    Tillapaugh, J A; Murphy, D J; Sommer, H J; Garvey, P M

    2010-10-01

    According to a 2004 National Institute for Occupational Safety and Health (NIOSH) report, approximately 250 to 350 fatalities occur each year due to incidents involving production agriculture workers and tractors. Tractor overturns account for about 150 to 200 of these deaths. The goals of this project were to study operators' understanding of tractor roll angles and test a device to effectively deliver stability information to the tractor operator. This project required the design and construction of a full-scale tractor cab roll simulator that was used to identify lateral roll angles at which volunteer participants felt uncomfortable, as well as lateral roll angles at which they would no longer operate a tractor. In addition, the participants performed a series of tasks to test the functionality of a visual slope indicator that was designed to help them estimate slope angles. The project tested 231 tractor operators' perceptions of safe operation on side slopes and 128 participants' interactions with the visual slope indicator. Testing showed that the visual slope indicator was able to influence the angle estimations of the novice tractor operator population and helped the entire population of participants more accurately rank the simulator scenarios.

  1. Active annular-beam laser autocollimator system.

    PubMed

    Yoder, P R; Schlesinger, E R; Chickvary, J L

    1975-08-01

    An autocollimator using an axicon and a beam expander telescope to generate a 12.5-cm. o.d. annular beam of helium-neon laser light with high (25:1) diameter-to-width ratio has been developed. It is used with a two-axis, electromagnetically actuated mirror assembly to acquire automatically and maintain dynamically autocollimation from a nearby but separately mounted annular mirror. The servo system controls beam alignment even though angular vibratory motions of the annular mirror make it appear to tilt relative to the autocollimator as much as 7 mrad at frequencies below 300 Hz. This paper describes the optical system and the alignment sensing and control system.

  2. Lube rack of Automotive and Tractor Repair Shops with Warehousefield ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Lube rack of Automotive and Tractor Repair Shops with Warehouse-field Equipment Repair Shop Building's wall to the right, looking from the south - Kekaha Sugar Company, Automotive and Tractor Repair Shops, 8315 Kekaha Road, Kekaha, Kauai County, HI

  3. View of south elevation of Automotive and Tractor Repair Shops ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of south elevation of Automotive and Tractor Repair Shops with the Warehouse Fabrication Shop and Stack in the background, looking from the southwest - Kekaha Sugar Company, Automotive and Tractor Repair Shops, 8315 Kekaha Road, Kekaha, Kauai County, HI

  4. North and east elevations of tractor shed facing southwest ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    North and east elevations of tractor shed facing southwest - Norris Farm, Tractor Shed-Combine Barn, .5 mile west of County Road 857 & .25 mile east of County Road 88/1, Cheat Neck, Monongalia County, WV

  5. South and west elevations of tractor shed facing northeast ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    South and west elevations of tractor shed facing northeast - Norris Farm, Tractor Shed-Combine Barn, .5 mile west of County Road 857 & .25 mile east of County Road 88/1, Cheat Neck, Monongalia County, WV

  6. Electron beam injection during active experiments. II - Collisional effects

    NASA Technical Reports Server (NTRS)

    Winglee, R. M.

    1990-01-01

    During active beam experiments, the presence of high neutral densities at low altitudes and/or during thruster firings has been observed to modify the spacecraft charging and the properties of the beam. Two-dimensional (three-velocity) electromagnetic particle simulations with ionizing collisions incorporated are used to investigate the modification of the beam-plasma interaction as the neutral density is increased. It is shown that when the spacecraft is uniformly immersed in a neutral cloud, most of the ionization is produced by direct ionization by the beam and its secondaries, rather than via vehicle-induced or wave-induced ionization for the neutral densities considered.

  7. 30 CFR 77.409 - Shovels, draglines, and tractors.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Shovels, draglines, and tractors. 77.409... COAL MINES Safeguards for Mechanical Equipment § 77.409 Shovels, draglines, and tractors. (a) Shovels, draglines, and tractors shall not be operated in the presence of any person exposed to a hazard from...

  8. Effectiveness of the Indiana 4-H Tractor Program: Alumni Perceptions.

    ERIC Educational Resources Information Center

    Carrabba, James J., Jr.; Talbert, B. Allen; Field, William E.; Tormoehlen, Roger

    2001-01-01

    Responses from Indiana 4-H tractor driving contestants 1982-197 (n=139) showed that 74% were employed on farms; most felt the contests effectively taught tractor safety and made them generally aware of safety. However, many still engaged in risky behaviors such as not wearing seatbelts in tractors with rollover protective structures or allowing…

  9. Tractor Mechanic--Teacher's Guide. Competency Based Education Curriculum.

    ERIC Educational Resources Information Center

    McCann, Edward W.

    This teacher's guide is designed to accompany the Tractor Mechanic Competency Based Education (CBE) Curriculum (CE 022 480). The following information is included: a discussion of the uses of the Tractor Mechanic CBE curriculum; definitions of related terms; the table of contents for the Tractor Mechanic CBE curriculum; a list of competencies by…

  10. Active control of flexural vibrations in beams

    NASA Technical Reports Server (NTRS)

    Gerhold, Carl H.

    1987-01-01

    The feasibility of using piezoelectric actuators to control the flexural oscillations of large structures in space is investigated. Flexural oscillations are excited by impulsive loads. The vibratory response can degrade the pointing accuracy of cameras and antennae, and can cause high stresses at structural node points. Piezoelectric actuators have the advantage of exerting localized bending moments. In this way, vibration is controlled without exciting rigid body modes. The actuators are used in collocated sensor/driver pairs to form a feedback control system. The sensor produces a voltage that is proportional to the dynamic stress at the sensor location, and the driver produces a force that is proportional to the voltage applied to it. The analog control system amplifies and phase shifts the sensor signal to produce the voltage signal that is applied to the driver. The feedback control is demonstrated to increase the first mode damping in a cantilever beam by up to 100 percent, depending on the amplifier gain. The damping efficiency of the control system when the piezoelectrics are not optimally positioned at points of high stress in the beam is evaluated.

  11. Electron beam injection during active experiments. I - Electromagnetic wave emissions

    NASA Technical Reports Server (NTRS)

    Winglee, R. M.; Kellogg, P. J.

    1990-01-01

    The wave emissions produced in Echo 7 experiment by active injections of electron beams were investigated to determine the properties of the electromagnetic and electrostatic fields for both the field-aligned and cross-field injection in such experiments and to evaluate the sources of free energy and relative efficiencies for the generation of the VLF and HF emissions. It is shown that, for typical beam energies in active experiments, electromagnetic effects do not substantially change the bulk properties of the beam, spacecraft charging, and plasma particle acceleration. Through simulations, beam-generated whistlers; fundamental z-mode and harmonic x-mode radiation; and electrostatic electron-cyclotron, upper-hybrid, Langmuir, and lower-hybrid waves were identified. The characteristics of the observed wave spectra were found to be sensitive to both the ratio of the electron plasma frequency to the cyclotron frequency and the angle of injection relative to the magnetic field.

  12. The Tractor Electrical System. A Teaching Reference.

    ERIC Educational Resources Information Center

    American Association for Vocational Instructional Materials, Athens, GA.

    The fundamental principles underlying the application of electricity to tractors and farm equipment are presented. An understanding of the material in the basic manual will enable the service man to understand better the service procedures covered in service manuals on electrical equipment. Topics dealt with are fundamentals of electricity,…

  13. Tractor Trailer Driver's Training Programs. Performance Report.

    ERIC Educational Resources Information Center

    New Hampshire Vocational Technical Coll., Nashua.

    This document describes a project to develop a 320-hour tractor trailer driver training program and a 20-hour commercial driver licensing upgrade training program. Of 34 graduates from the training program, 28 secured employment in the trucking industry. From August 1989 to June 1990, 725 students were trained in the upgrade training program with…

  14. Polyhedron tracking and gravity tractor asteroid deflection

    NASA Astrophysics Data System (ADS)

    Ummen, N.; Lappas, V.

    2014-11-01

    In the wake of the Chelyabinsk airburst, the defense against hazardous asteroids is becoming a topic of high interest. This work improves the gravity tractor asteroid deflection approach by tracking realistic small body shapes with tilted ion engines. An algorithm for polyhedron tracking was evaluated in a fictitious impact scenario. The simulations suggest a capability increase up to 38.2% with such improved tilting strategies. The long- and short-term effects within polyhedron tracking are illustrated. In particular, the orbital reorientation effect is influential when realistic asteroid shapes and rotations are accounted for. Also analyzed is the subject of altitude profiles, a way to tailor the gravity tractor performance, and to achieve a steering ability within the B-plane. A novel analytical solution for the classic gravity tractor is derived. It removes the simulation need for classic tractor designs to obtain comparable two body model Δv figures. This paper corroborates that the asteroid shape can be exploited for maximum performance. Even a single engine tilt adjustment at the beginning of deflection operations yields more deflection than a fixed preset tilt.

  15. Extra-safe tractor-trailer coupling

    NASA Technical Reports Server (NTRS)

    Albrecht, W. P.; Sparks, R. H.

    1979-01-01

    Built-in safety mechanism for tractor-trailer "fifth-wheel" coupling keeps rig together in case kingpin failure. Modified coupling utilizes all standard components, such as two wear plates, kingpin, and kingpin latch. It is modified by adding semicircular lip to top wear plate, matching semicircular slot to bottom wear plate, and two latching stop mechanisms.

  16. V-TECS Guide for Tractor Mechanic.

    ERIC Educational Resources Information Center

    Benson, Robert T.

    This guide contains a course outline for a tractor mechanic course. The outline is organized by 15 duties: performing general skills and maintaining and servicing storage battery, ignition circuit, the cooling system, the charging circuit, the starting circuit, gasoline fuel system, diesel fuel system, basic engine, lubrication system, clutches,…

  17. Tractor Mechanic Check Sheets for Modules.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    Forms for student self-checks and the instructor's final checklist (student evaluation) are provided for use with thirty-three learning modules on maintaining and servicing fuel and electrical systems in tractor mechanics. The student self-check asks the students questions about their understanding of the modules' content. The instructor's…

  18. Vibration control of flexible beams using an active hinge

    NASA Technical Reports Server (NTRS)

    Cudney, H. H., Jr.; Inman, D. J.; Horner, G. C.

    1985-01-01

    The use of an active hinge to attenuate the transverse vibrations of a flexible beam is examined. A slender aluminum beam is suspended vertically, cantilevered at the top. An active hinge is placed at the node of the second vibration mode. The active hinge consists of a torque motor, strain gauge, and tachometer. A control law is implemented using both beam-bending strain and the relative angular velocity measured at this hinge, thereby configuring the hinge to act as an active damper. Results from implementing this control law show little improvement in the first mode damping ratio, 130 percent increase in the second mode damping ratio, and 180 percent increase in the third mode damping ratio. The merits of using a motor with a gearbox are discussed.

  19. Application of activity pencil beam algorithm using measured distribution data of positron emitter nuclei for therapeutic SOBP proton beam

    SciTech Connect

    Miyatake, Aya; Nishio, Teiji

    2013-09-15

    Purpose: Recently, much research on imaging the clinical proton-irradiated volume using positron emitter nuclei based on target nuclear fragment reaction has been carried out. The purpose of this study is to develop an activity pencil beam (APB) algorithm for a simulation system for proton-activated positron-emitting imaging in clinical proton therapy using spread-out Bragg peak (SOBP) beams.Methods: The target nuclei of activity distribution calculations are {sup 12}C nuclei, {sup 16}O nuclei, and {sup 40}Ca nuclei, which are the main elements in a human body. Depth activity distributions with SOBP beam irradiations were obtained from the material information of ridge filter (RF) and depth activity distributions of compounds of the three target nuclei measured by BOLPs-RGp (beam ON-LINE PET system mounted on a rotating gantry port) with mono-energetic Bragg peak (MONO) beam irradiations. The calculated data of depth activity distributions with SOBP beam irradiations were sorted in terms of kind of nucleus, energy of proton beam, SOBP width, and thickness of fine degrader (FD), which were verified. The calculated depth activity distributions with SOBP beam irradiations were compared with the measured ones. APB kernels were made from the calculated depth activity distributions with SOBP beam irradiations to construct a simulation system using the APB algorithm for SOBP beams.Results: The depth activity distributions were prepared using the material information of RF and the measured depth activity distributions with MONO beam irradiations for clinical therapy using SOBP beams. With the SOBP width widening, the distal fall-offs of depth activity distributions and the difference from the depth dose distributions were large. The shapes of the calculated depth activity distributions nearly agreed with those of the measured ones upon comparison between the two. The APB kernels of SOBP beams were prepared by making use of the data on depth activity distributions with SOBP

  20. Electron-beam activated GaAs-switches

    SciTech Connect

    Kirkman, G.; Hur, J.; Jiang, B.; Reinhardt, N.; Allen, R.J.; Schoenbach, K.H.

    1994-12-31

    Electron-beam excitation allows the authors to modulate the conductance of wide-gap semi-insulating semiconductors over a wide range and to use them as variable resistors and as high power switches. The penetration depth of electrons, the electron range, was computed by means of a Monte-Carlo code. For electron energies of 30 keV, it is approximately 2 micrometers. In order to activate the switch material over a larger depth, the switch material, semi-insulating GaAs, was doped over a thickness corresponding to the electron range with zinc, which form shallow acceptors in GaAs. The Zn layers serves as an efficient source of cathodoluminescence, transforming the electron energy into photon energy and therefore converting the electron-beam activated switch into a photoconductive one. Experiments with 2 mm semi-insulating GaAs-switches with p-doped cathode layer have been performed where the electron beam was injected through one of the metal contacts which were placed on either face of the GaAs wafer. The 500 ns electron beam has electron energies of up to 30 keV and current densities of several A/cm{sup 2}. The results show that electron-beam controlled GaAs switches can be safely operated at switch voltages of several kV`s and current densities of 50 A/cm{sup 2} with low energy electron-beams as control elements.

  1. Activation of cells using femtosecond laser beam (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Batabyal, Subrata; Satpathy, Sarmishtha; Kim, Young-tae; Mohanty, Samarendra K.

    2016-03-01

    Study of communication in cellular systems requires precise activation of targeted cell(s) in the network. In contrast to chemical, electrical, thermal, mechanical stimulation, optical stimulation is non-invasive and is better suited for stimulation of targeted cells. As compared to visible lasers, the near infrared (NIR) microsecond/nanosecond pulsed laser beams are being used as preferred stimulation tool as they provide higher penetration depth in tissues. Femotosecond (FS) laser beams in NIR are also being used for direct and indirect (i.e. via two-photon optogenetics) stimulation of cells. Here, we present a comparative evaluation of efficacy of NIR FS laser beam for direct (no optogenetic sensitization) and 2ph optogenetic stimulation of cells. Further, for the first time, we demonstrate the use of blue (~450 nm, obtained by second harmonic generation) FS laser beam for stimulation of cells with and without Channelrhodopisn-2 (ChR2) expression. Comparative analysis of photocurrent generated by blue FS laser beam and continuous wave blue light for optogenetics stimulation of ChR2 transfected HEK cells will be presented. The use of ultrafast laser micro-beam for focal, non-contact, and repeated stimulation of single cells in a cellular circuitry allowed us to study the communication between different cell types.

  2. The development of enabling technologies for producing active interrogation beams

    SciTech Connect

    Kwan, Thomas J. T.; Morgado, Richard E.; Wang, Tai-Sen F.; Vodolaga, B.; Terekhin, V.; Onischenko, L. M.; Vorozhtsov, S. B.; Samsonov, E. V.; Vorozhtsov, A. S.; Alenitsky, Yu. G.; Perpelkin, E. E.; Glazov, A. A.; Novikov, D. L.; Parkhomchuk, V.; Reva, V.; Vostrikov, V.; Mashinin, V. A.; Fedotov, S. N.; Minayev, S. A.

    2010-10-15

    A U.S./Russian collaboration of accelerator scientists was directed to the development of high averaged-current ({approx}1 mA) and high-quality (emittance {approx}15 {pi}mm mrad; energy spread {approx}0.1%) 1.75 MeV proton beams to produce active interrogation beams that could be applied to counterterrorism. Several accelerator technologies were investigated. These included an electrostatic tandem accelerator of novel design, a compact cyclotron, and a storage ring with energy compensation and electron cooling. Production targets capable of withstanding the beam power levels were designed, fabricated, and tested. The cyclotron/storage-ring system was theoretically studied and computationally designed, and the electrostatic vacuum tandem accelerator at BINP was demonstrated for its potential in active interrogation of explosives and special nuclear materials.

  3. The development of enabling technologies for producing active interrogation beams.

    PubMed

    Kwan, Thomas J T; Morgado, Richard E; Wang, Tai-Sen F; Vodolaga, B; Terekhin, V; Onischenko, L M; Vorozhtsov, S B; Samsonov, E V; Vorozhtsov, A S; Alenitsky, Yu G; Perpelkin, E E; Glazov, A A; Novikov, D L; Parkhomchuk, V; Reva, V; Vostrikov, V; Mashinin, V A; Fedotov, S N; Minayev, S A

    2010-10-01

    A U.S./Russian collaboration of accelerator scientists was directed to the development of high averaged-current (∼1 mA) and high-quality (emittance ∼15 πmm mrad; energy spread ∼0.1%) 1.75 MeV proton beams to produce active interrogation beams that could be applied to counterterrorism. Several accelerator technologies were investigated. These included an electrostatic tandem accelerator of novel design, a compact cyclotron, and a storage ring with energy compensation and electron cooling. Production targets capable of withstanding the beam power levels were designed, fabricated, and tested. The cyclotron/storage-ring system was theoretically studied and computationally designed, and the electrostatic vacuum tandem accelerator at BINP was demonstrated for its potential in active interrogation of explosives and special nuclear materials.

  4. Active local volume displacement cancellation of a vibrating baffled beam

    NASA Astrophysics Data System (ADS)

    Zahui, Marcellin

    An active noise control apparatus is developed. The device reduces the sound radiated from a vibrating clamped beam. The attenuation of the sound field is obtained through minimization of local volume displacements of the vibrating beam. Two single- input/single-output cancellation devices are used. Each device employs a motion sensor and an acoustic actuator. The actuator is a loudspeaker equipped with a pressure sensor to detect its volume displacement. The motion sensor signal is related to the local volume displacement of the structure which is then reduced by a loudspeaker driven with an equal but opposing volume displacement. The volume displacement sensors are developed and fabricated using Polyvinylidene Fluoride (PVDF). They measure the local volume displacements of the vibrating beam. The pressure sensor is mounted in the loudspeaker enclosure. It provides the feedback signal for the loudspeaker volume displacement control. Previous work showed the successful implementation of this technique for uniformly vibrating radiators. This thesis presents the development of this technique for the reduction of sound radiated from a vibrating beam. First, a numerical local volume displacement cancellation experiment is performed using several loudspeakers, each canceling the volume displacement of a section of the beam. The finite element method is used to calculate the velocity distribution of the vibrating beam. A discretized form of the Rayleigh integral is then used to find the sound pressure and the sound power radiated before and after cancellation. Second, the numerical results are verified by laboratory experiments using a beam divided into two sections. Two motion sensors for the beam and one pressure sensor for each loudspeaker are fabricated and thoroughly checked. The cancellation experiment is then performed on a broadband random noise using two independent Proportional-Derivative (PD) controllers.

  5. Adoption of rollover protective structures (ROPS) on U.S. farm tractors by state: 1993-1995, 2001, and 2004.

    PubMed

    Hard, D L; Myers, J R

    2011-04-01

    This research compares state-level rollover protective structure (ROPS) prevalence rates from the early and mid-1990s to those observed in the years 2001 and 2004. In addition, state-level ROPS prevalence rates are compared to state-level tractor overturn fatality rates. Tractor data for 1993-1995 and for 2001 and 2004 for all tractors and ROPS-equipped tractors in use on U.S. farms were derived from surveys conducted for NIOSH by the USDA-NASS. Changes in ROPS prevalence rates at the state level between the two time periods were assessed using a two-sample paired t-test with unequal sample sizes. Poisson regression was used to assess the association between ROPS prevalence rates and tractor overturn fatality rates at the state level. Overall, 49 of the 50 states had an observed increase in the percentage of farm tractors equipped with ROPS from 1993-1995 to 2001 and 2004. This increase was statistically significant for 34 states. Large shifts in ROPS prevalence were found within individual states and in clusters of states. These include a major increase in the southeastern U.S. and some western states. However, a core of states in the northeast (many of them in or near the Appalachian Mountains) through the upper midwest remain in the bottom quartile for ROPS prevalence. For the years 1992 through 2004, the highest fatality rates were observed in many of the same states that were identified previously as having persistently low ROPS prevalence rates. There is a clear relationship between low state-level ROPS prevalence rates and high state-specific tractor overturn fatality rates. While progress has been made in increasing the percentage of ROPS-equipped farm tractors, it is projected that ROPS prevalence rates will not reach a protective level nationally until after 2015. Regionally, the northeast and midwest will not reach protective levels of ROPS-equipped tractors until after 2020. Based on the adoption rates observed, tractor overturn rates will likely

  6. Drug use by tractor-trailer drivers.

    PubMed

    Lund, A K; Preusser, D F; Blomberg, R D; Williams, A F

    1988-05-01

    Blood or urine samples or both were obtained from 317 of 359 randomly selected tractor-trailer drivers asked to participate in a driver health survey conducted at a truck weighing station on Interstate 40 in Tennessee. Altogether, 29% of the drivers had evidence of alcohol, marijuana, cocaine, prescription or nonprescription stimulants, or some combination of these, in either blood or urine. Cannabinoids were found in 15% of the drivers' blood or urine; nonprescription stimulants such as phenylpropanolamine were found in 12%; prescription stimulants such as amphetamine were found in 5%; cocaine metabolites were found in 2%; and alcohol was found in less than 1%. These results provide the first objective information about the use of potentially abusive drugs by tractor-trailer drivers. The extent of driver impairment attributable to the observed drugs is uncertain because of the complex relationship between performance and drug concentrations.

  7. Farm Tractor Tune-Up and Service Specifications.

    ERIC Educational Resources Information Center

    Bryant, J. G.; And Others

    Tune-up and service specifications for 10 major tractor manufacturers are presented in the handbook. In addition, the following tables are included: (1) spark plug heat-range comparisons, (2) freezing protection, (3) pressures for farm tractor tires, (4) use of calcium chloride for liquid weighting, (5) comparisons of American Petroleum Institute…

  8. Agricultural Tractor Safety on Public Roads and Farms.

    ERIC Educational Resources Information Center

    Department of Transportation, Washington, DC.

    This study investigated the extent, causes, and means of preventing agricultural tractor accidents. The report includes an estimate of annual tractor-related deaths, an identification of the primary causes of such accidents with consideration of the major hazards causing death or injury, and recommendations or means for preventing the occurrence…

  9. MTR MAIN FLOOR. MTR TRACTOR IS IN CENTER OF VIEW ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    MTR MAIN FLOOR. MTR TRACTOR IS IN CENTER OF VIEW AMIDST AN ACCUMULATION OF CLUTTER ON THE FLOOR. TRACTOR HAD ATTACHMENTS IN FRONT TO FACILITATE MOVING OF COFFINS. INL NEGATIVE NO. 56-3027. Jack L. Anderson, Photographer, 9/17/1956 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

  10. Development of a small high-thrust tractor rocket motor

    SciTech Connect

    Carr, C.E.; Oberlander, W.F.

    1986-01-01

    This paper summarizes the parachute extraction tractor rocket motor design and test efforts conducted during the Sandia ASW/SOW development program. The prime contractor was Sandia National Laboratories, Albuquerque, New Mexico; the tractor rocket motor subcontractor was Morton Thiokol, Inc., Elkton, Maryland.

  11. Perceptions of tilt angles of an agricultural tractor.

    PubMed

    Görücü, Serap; Cavallo, Eugenio; Murphy, Dennis

    2014-01-01

    A tractor stability simulator has been developed to help study tractor operators' perceptions of angles when the simulator is tilted to the side. The simulator is a trailer-mounted tractor cab equipped with hydraulic lift that can tilt the tractor cabin up to 30 degrees. This paper summarizes data from 82 participants who sat in the simulator while it was tilted. Demographic variables, estimates of tilt angles, and measured tilt angles were collected. The effects of age, gender, tractor driving experience, and frequency of operation on the estimated and measured tilt angles were analyzed. The results showed that about 50% of the participants reported estimations of side tilt angles within ±5 degrees of the actual angles, and nearly the same percentage overestimated the actual side tilt angles. Only a small percentage underestimated the angles. Older, more experienced, and male participants set higher limits on the actual angle at which they felt uncomfortable and would not drive. PMID:24417527

  12. Enhanced Gravity Tractor Technique for Planetary Defense

    NASA Technical Reports Server (NTRS)

    Mazanek, Daniel D.; Reeves, David M.; Hopkins, Joshua B.; Wade, Darren W.; Tantardini, Marco; Shen, Haijun

    2015-01-01

    Given sufficient warning time, Earth-impacting asteroids and comets can be deflected with a variety of different "slow push/pull" techniques. The gravity tractor is one technique that uses the gravitational attraction of a rendezvous spacecraft to the impactor and a low-thrust, high-efficiency propulsion system to provide a gradual velocity change and alter its trajectory. An innovation to this technique, known as the Enhanced Gravity Tractor (EGT), uses mass collected in-situ to augment the mass of the spacecraft, thereby greatly increasing the gravitational force between the objects. The collected material can be a single boulder, multiple boulders, regolith or a combination of different sources. The collected mass would likely range from tens to hundreds of metric tons depending on the size of the impactor and warning time available. Depending on the propulsion system's capability and the mass collected, the EGT approach can reduce the deflection times by a factor of 10 to 50 or more, thus reducing the deflection times of several decades to years or less and overcoming the main criticism of the traditional gravity tractor approach. Additionally, multiple spacecraft can orbit the target in formation to provide the necessary velocity change and further reduce the time needed by the EGT technique to divert hazardous asteroids and comets. The robotic segment of NASA's Asteroid Redirect Mission (ARM) will collect a multi-ton boulder from the surface of a large Near-Earth Asteroid (NEA) and will provide the first ever demonstration of the EGT technique and validate one method of collecting in-situ mass on an asteroid of hazardous size.

  13. 78 FR 51724 - California State Motor Vehicle Pollution Control Standards; Tractor-Trailer Greenhouse Gas...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-21

    ... AGENCY California State Motor Vehicle Pollution Control Standards; Tractor-Trailer Greenhouse Gas...: The California Air Resources Board (CARB) has notified EPA that it has adopted a tractor-trailer... new and in-use tractors that haul such trailers on California highways (HD Tractor-Trailer...

  14. Passive and active plasma deceleration for the compact disposal of electron beams

    SciTech Connect

    Bonatto, A.; Schroeder, C. B.; Vay, J.-L.; Geddes, C. G. R.; Benedetti, C.; Esarey, E.; Leemans, W. P.

    2015-08-15

    Plasma-based decelerating schemes are investigated as compact alternatives for the disposal of high-energy beams (beam dumps). Analytical solutions for the energy loss of electron beams propagating in passive and active (laser-driven) schemes are derived. These solutions, along with numerical modeling, are used to investigate the evolution of the electron distribution, including energy chirp and total beam energy. In the active beam dump scheme, a laser-driver allows a more homogeneous beam energy extraction and drastically reduces the energy chirp observed in the passive scheme. These concepts could benefit applications requiring overall compactness, such as transportable light sources, or facilities operating at high beam power.

  15. Farming tractor fatalities in Virginia: an 11-year retrospective review.

    PubMed

    Fulcher, James; Noller, Anna; Kay, Deborah

    2012-12-01

    This retrospective case review examines farm tractor-related deaths in the Commonwealth of Virginia for an 11-year period, from 1997 to 2007. This study compares decedent's demographic information, toxicology results, and medical histories.A vast majority of farm tractor-related deaths were male (98%) and white (91%). The average age was 60 years with most deaths occurring between the ages of 40 and 80 years. Ethanol use was observed in 9% of all cases with 7% of cases being more than 0.08% wt/vol ethanol, which is the legal limit in Virginia to operate a motor vehicle.The more mountainous, Western District Office of the Chief Medical Examiner composed 60% of total cases with 43% of these western cases related to tractor use on a natural slope or incline. The deaths in other districts were all less than 13% natural slope or incline related, reflecting the topography of these areas.These findings confirm much of what observation would suggest; accidents with farming tractors typically involve older white men. Operating a tractor on steep inclines is dangerous as many tractors do not have adequate rollover protection. The use of ethanol is dangerous when using any heavy equipment.This study provides an initial look at tractor-related deaths in Virginia, and more research is needed in this area to improve safety mechanisms on this machinery.

  16. A simple method to improve autonomous GPS positioning for tractors.

    PubMed

    Gomez-Gil, Jaime; Alonso-Garcia, Sergio; Gómez-Gil, Francisco Javier; Stombaugh, Tim

    2011-01-01

    Error is always present in the GPS guidance of a tractor along a desired trajectory. One way to reduce GPS guidance error is by improving the tractor positioning. The most commonly used ways to do this are either by employing more precise GPS receivers and differential corrections or by employing GPS together with some other local positioning systems such as electronic compasses or Inertial Navigation Systems (INS). However, both are complex and expensive solutions. In contrast, this article presents a simple and low cost method to improve tractor positioning when only a GPS receiver is used as the positioning sensor. The method is based on placing the GPS receiver ahead of the tractor, and on applying kinematic laws of tractor movement, or a geometric approximation, to obtain the midpoint position and orientation of the tractor rear axle more precisely. This precision improvement is produced by the fusion of the GPS data with tractor kinematic control laws. Our results reveal that the proposed method effectively reduces the guidance GPS error along a straight trajectory.

  17. A mathematical equation for quantifying control functionality in agricultural tractors.

    PubMed

    Drakopoulos, D; Mann, D D

    2008-10-01

    The overall accessibility of controls is one of the most important issues to consider when designing a control layout. Well-arranged controls, whose operational characteristics are based on both design guidelines and on human factors considerations, allow the operator to efficiently interact with the system in question. The objective of this article is to introduce a numerical index, referred to as the "index of functionality", capable of comparing, on a mathematical basis, different control arrangements in agricultural tractors. The model is based on information that has been gleaned from the published literature, with input from both professional ergonomists and experienced agricultural tractor operators. The numerical index may take any value between 0 and +1, with +1 being defined as an optimum value in terms of the functionality of a workstation. Data were collected from six old (pre-1982) and six modern (post-2003) tractor workstations to determine whether the model would recognize improvements that have occurred in the ergonomic design of tractor control layouts over the past 20 years. An average score of 0.19 +/- 0.07 was calculated for the pre-1982 tractor workstations. By contrast, an average score of 0.63 +/- 0.10 was calculated for the post-2003 tractor workstations. A number of limitations have been identified with the current model; despite these limitations, the index of functionality clearly recognized the ergonomic improvements in tractor workstations that have occurred over the past 20 years. PMID:19044167

  18. A Simple Method to Improve Autonomous GPS Positioning for Tractors

    PubMed Central

    Gomez-Gil, Jaime; Alonso-Garcia, Sergio; Gómez-Gil, Francisco Javier; Stombaugh, Tim

    2011-01-01

    Error is always present in the GPS guidance of a tractor along a desired trajectory. One way to reduce GPS guidance error is by improving the tractor positioning. The most commonly used ways to do this are either by employing more precise GPS receivers and differential corrections or by employing GPS together with some other local positioning systems such as electronic compasses or Inertial Navigation Systems (INS). However, both are complex and expensive solutions. In contrast, this article presents a simple and low cost method to improve tractor positioning when only a GPS receiver is used as the positioning sensor. The method is based on placing the GPS receiver ahead of the tractor, and on applying kinematic laws of tractor movement, or a geometric approximation, to obtain the midpoint position and orientation of the tractor rear axle more precisely. This precision improvement is produced by the fusion of the GPS data with tractor kinematic control laws. Our results reveal that the proposed method effectively reduces the guidance GPS error along a straight trajectory. PMID:22163917

  19. Active retrodirective arrays for SPS beam pointing. [phase conjugation

    NASA Technical Reports Server (NTRS)

    Chernoff, R.

    1980-01-01

    The basic requirement of the SPS beam pointing system is that it deliver a certain amount of S-band (lambda = 12.5 cm) power to a 9.6 km diameter receiving rectenna on the ground. The power is transmitted from a 1.0 km diameter antenna array on the SPS, which is, for a rectenna at about plus or minus 40 deg. latitude, some 37.5x10 to the 6th power km distant. At the present time ARA's appear to be the best bet to realize this very stringent beam pointing requirement. An active retrodirective array (ARA) transmits a beam towards the apparent source of an illuminating signal called the pilot. The array produces, not merely reflects, RF power. Retrodirectivity is achieved by retransmitting from each element of the array a signal whose phase is the "conjugate" of that received by the element. Phase conjugate circuits and pointing errors in ARA's are described. Results obtained using a 2-element X-band ARA and an 8-element S-band ARA are included.

  20. Narrow-track wheeled agricultural tractor parameter variation.

    PubMed

    Guzzomi, A; Rondelli, V

    2013-10-01

    Despite a general consensus among farmers, manufacturers, and researchers that wheeled agricultural tractor design has changed over time, there is little published evidence. There is debate as to whether the standardized rollover protective structure (ROPS) energy and force requirements, based on a tractor reference mass and pertaining to studies conducted more than 40 years ago, are appropriate for modern tractors. This article investigated the physical parameters of 326 modern narrow-track tractors, measured according to OECD Code 6 over 16 years (1993 to 2008 inclusive): 252 (-77%) were fixed-chassis tractors and 74 (-23%) were articulated. To understand the significance of design changes, the data were analyzed with respect to time and as a function of tractor mass. Articulated and fixed-chassis data were treated separately. The time data allowed qualitative analysis, while the mass data allowed quantitative analysis. The parameters show some changes over time and clearly indicate differences between articulated and fixed-chassis types. The parameter changes, along with the differences between types, may have important safety ramifications for ROPS energy absorption requirements, and these aspects are discussed. Regression lines with R2 values were fitted to the mass-related data for fixed-chassis and articulated tractors to determine the suitability of fit. The mass relations also displayed differences between fixed-chassis and articulated tractors. Thus, the most significant recommendation from this study is that the standardized testing procedure for narrow-track wheeled agricultural tractor category should be split into two groups: fixed-chassis and articulated. PMID:24673034

  1. Risk analysis of tractor overturns on catfish farms.

    PubMed

    Stephens, Walter B; Ibendahl, Gregory A; Myers, Melvin L; Cole, Henry P

    2010-10-01

    Fatal and nonfatal injuries occur on catfish farms as a result of tractor overturns, but these injuries can be greatly mitigated when a tractor is equipped with a rollover protective structure (ROPS) and seatbelt. This study analyzed the proportion of tractors on catfish farms in Mississippi not equipped with ROPS and the cost of retrofitting those tractors with a ROPS and seatbelt as compared to the expected benefits gained from adding the protection. To determine if farmers have the financial incentive to retrofit older tractors, a net present value framework was used because the expected benefits occur over a number of years. The ROPS retrofit is a one-time cost that occurs immediately, and thus the present value does not need to be calculated, i.e., time period 0. According to this study adding ROPS will provide a net benefit of $22,877 in the event of an overturn. When dealing with small farms (<125 acres) where an average tractor is used for approximately twice as many hours compared to an average tractor on large farms, the extra hours worked by a single tractor resulted in total benefits of retrofitting ROPS of $9.45 per year, whereas for large farms the net benefit is $4.70 (=125 acres). Given that the least expensive retrofit is $147, it would take 15.5 years of tractor use on the small farms for the expected benefits to outweigh the cost. Given the large range of costs that could occur due to an overturn, there could be a significant premium for not having ROPS protection. In other words, there likely is a smaller range of costs from an overturn with ROPS than without ROPS because ROPS reduces the more serious incidents. PMID:20954036

  2. DETAIL VIEW OF STEAM TRACTOR "OLD DINAH," LOOKING NORTHWEST. THIS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW OF STEAM TRACTOR "OLD DINAH," LOOKING NORTHWEST. THIS STEAM TRACTOR WAS USED TO REPLACE THE HORSE WAGON TRAINS THAT CARRIED SUPPLIES AND CRUDE OIL THE 26 MILES FROM BEATTY, NEVADA TO KEANE WONDER. THE TRACTOR ONLY MADE ONE RUN IN 1909 BEFORE THE BOILER EXPLODED ENROUTE, AND IT WAS ABANDONED THERE ON THE TRAIL TODAY IT STANDS ON DISPLAY AT THE FURNACE CREEK RANCH IN DEATH VALLEY NATIONAL PARK, AS SEEN IN THE PHOTOGRAPH. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

  3. VIEW OF STACK WITH AUTOMOBILE AND TRACTOR REPAIR SHOP TO ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF STACK WITH AUTOMOBILE AND TRACTOR REPAIR SHOP TO THE FAR RIGHT. WAREHOUSE WITH ITS RIDGELINE ROTARY VENTS TO RIGHT OF STACK. VIEW FROM THE WEST - Kekaha Sugar Company, Sugar Mill Building, 8315 Kekaha Road, Kekaha, Kauai County, HI

  4. Environmental perspective facing south showing chicken house, tractor shed, and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Environmental perspective facing south showing chicken house, tractor shed, and homestead - Norris Farm, .5 mile west of County Road 857 & .25 mile east of County Road 88/1, Cheat Neck, Monongalia County, WV

  5. [Ergonomic evaluation of assembly line of tractors].

    PubMed

    Dellera, L; Buratti, G

    2012-01-01

    In the assembly lines in the engineering sector, ever more guided by the theories of lean production, is increasingly important ergonomic factor working conditions to preserve the health of workers and ensuring the performance. This analysis has focused on the study of biomechanical and postural stress of work tasks of an assembly line of the tractor, characterized by different weights and volumes from that of the car. Comparison with the technical standard of EN 1005-4 has allowed the identification as the machining assembly of small components result in conditions of acceptability, while most of the other processes aren't reliable. The emergence of these problems pushed to find several ergonomic solutions including the development of a special reclining seat to enable a proper posture during the working. PMID:23405593

  6. Schedule tightness among tractor-trailer drivers.

    PubMed

    Beilock, Richard

    2003-06-01

    The extent to which schedules are sufficiently tight to encourage violations of Hours-of-Service Regulations, speed limits, or both was investigated through a survey of over 1,600 tractor-trailer drivers. The focus was on drivers with refrigerated trailers. The results indicate high incidence levels of tight schedules. For example, assuming average speed limits of 65 mph, 24% had violation-inducing schedules with regard to the movement they were making at the time of the interviews. Incorporating information about previous driving, the incidence of violation-inducing schedules rose to 40%. Comparison with an earlier study suggests that, despite increases in speed limits which would tend to loosen schedules, schedules have become tighter over the past decade. The implications of these findings for reforms of Hours-of-Service Regulations are briefly discussed.

  7. Laser beam active brazing of metal ceramic joints

    NASA Astrophysics Data System (ADS)

    Haferkamp, Heinz; Bach, Friedrich W.; von Alvensleben, Ferdinand; Kreutzburg, K.

    1996-04-01

    The use of engineering ceramics is becoming more and more important. Reasons for this are the specific properties of these materials, such as high strength, corrosion resistance and wear resistance. To apply the advantages of ceramics, joining techniques of metal ceramic parts are required. In this paper, joining of metal ceramic joints by laser beam brazing is presented. This joining technique is characterized by local heat input, and the minimal thermal stress of the brazed components. During the investigations, an Nd:YAG laser and a vacuum chamber were applied. The advantages of Nd:YAG lasers are the simple mechanical construction, and laser beam guidance via quartz glass fibers, which leads to high handling flexibility. In addition, most of the materials show a high absorption rate for this kind of radiation. As materials, ceramic Al2O3 with a purity of 99.4% and metals such as X5CrNi189 and Fe54Ni29Co17 were used. As a filler material, commercially available silver and silver- copper brazes with chemically active elements like titanium were employed. During this study, the brazing wetting behavior and the formation of diffusion layers in dependence on processing parameters were investigated. The results have shown that high brazing qualities can be achieved by means of the laser beam brazing process. Crack-free joining of metal ceramic parts is currently only possible by the use of metals such as Fe54Ni29Co17 because of its low thermal expansion coefficient, which reduces thermal stresses within the joining zone.

  8. Linear analysis of active-medium two-beam accelerator

    NASA Astrophysics Data System (ADS)

    Voin, Miron; Schächter, Levi

    2015-07-01

    We present detailed development of the linear theory of wakefield amplification by active medium and its possible application to a two-beam accelerator (TBA) is discussed. A relativistic train of triggering microbunches traveling along a vacuum channel in an active medium confined by a cylindrical waveguide excites Cherenkov wake in the medium. The wake is a superposition of azimuthally symmetric transverse magnetic modes propagating along a confining waveguide, with a phase velocity equal to the velocity of the triggering bunches. The structure may be designed in such a way that the frequency of one of the modes is close to active-medium resonant frequency, resulting in amplification of the former and domination of a single mode far behind the trigger bunches. Another electron bunch placed in proper phase with the amplified wakefield may be accelerated by the latter. Importantly, the energy for acceleration is provided by the active medium and not the drive bunch as in a traditional TBA. Based on a simplified model, we analyze extensively the impact of various parameters on the wakefield amplification process.

  9. Active vibration control of a free-free beam by using a tendon mechanism

    NASA Astrophysics Data System (ADS)

    Tani, Junji; Ueda, Hiroki

    This paper is concerned with an active vibration control of a free-free beam. The beam is reduced to a finite-degree-of-freedom system by the modal analysis, in which the mode function is derived from the transfer matrix method. A control force is produced by a pair of tendons and a DC servo motor attached to the beam. The state of the beam is presumed by the minimum order state observer and the control force is determined by the digital optimum regulator theory. It is found that the active tendon control method is effective to suppress the vibration of the free-free beam.

  10. The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

    PubMed Central

    Gomez-Gil, Jaime; Gomez-Gil, Francisco Javier; Martin-de-Leon, Rebeca

    2014-01-01

    Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i) lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii) lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii) in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv) vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations. PMID:25340448

  11. The influence of tractor-seat height above the ground on lateral vibrations.

    PubMed

    Gomez-Gil, Jaime; Gomez-Gil, Francisco Javier; Martin-de-Leon, Rebeca

    2014-01-01

    Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i) lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii) lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii) in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv) vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations. PMID:25340448

  12. Treatment of industrial effluents using electron beam accelerator and adsorption with activated carbon: a comparative study

    NASA Astrophysics Data System (ADS)

    de Oliveira Sampa, Maria Helena; Rela, Paulo Roberto; Casas, Alexandre Las; Mori, Manoel Nunes; Duarte, Celina Lopes

    2004-09-01

    This paper presents preliminary results of a study that compares the use of electron beam processing and activated carbon adsorption to clean up a standardized organic aqueous solution and a real industrial effluent. The electron beam treatment was performed in a batch system using the IPEN's Electron Beam Accelerators from Radiation Dynamics Inc., Dynamitron 37.5 kW. The granular activated carbon removal treatment was performed using charcoal made from wood "pinus". If the adequate irradiation dose is delivered to the organic pollutant, it is possible to conclude for the studied compounds that the Electron Beam Process is similar to the activated carbon process in organic removal efficiency.

  13. Ensuring Machine and Tractor Aggregates Operability

    NASA Astrophysics Data System (ADS)

    Redreev, G. V.

    2016-08-01

    the operability of the machine and tractor aggregates is ensured by processes which occur in machine units and considered as technical systems. In order to develop theoretical understanding of the processes in technical systems as the basis and purpose of the repairserving actions, the author's concept is presented which relies on on the basic concepts of "processes in technical systems", "maintenance and repair of performers", "maintenance and repair of technology" "objectives of the maintenance and repair". Analysis of the basic concepts of "processes in technical systems" made possible to distinguishing four types of relations: of order, stipulation, exactingness, and non-contradiction. It is shown that the implementation of maintenance and repair of technology should be conducted according to the assessment of the effectiveness of processes in technical systems, revealed in complex diagnosis. The perfection of the design of the machine in terms of its technical operation can be estimated according to the degree of consistency of processes in technical systems, purposes of maintenance and repair. In order to increase the efficiency of the lubrication system,the modernised design of the centrifugal oil filter with permanent control of its cleaning power is offered, which allows changing the technology of the maintenance of engine lubrication system by separating the operations of crankcase oil replacement and the rotor filter cleaning.

  14. Working group report on beam plasmas, electronic propulsion, and active experiments using beams

    NASA Technical Reports Server (NTRS)

    Dawson, J. M.; Eastman, T.; Gabriel, S.; Hawkins, J.; Matossian, J.; Raitt, J.; Reeves, G.; Sasaki, S.; Szuszczewicz, E.; Winkler, J. R.

    1986-01-01

    The JPL Workshop addressed a number of plasma issues that bear on advanced spaceborne technology for the years 2000 and beyond. Primary interest was on the permanently manned space station with a focus on identifying environmentally related issues requiring early clarification by spaceborne plasma experimentation. The Beams Working Group focused on environmentally related threats that platform operations could have on the conduct and integrity of spaceborne beam experiments and vice versa. Considerations were to include particle beams and plumes. For purposes of definition it was agreed that the term particle beams described a directed flow of charged or neutral particles allowing single-particle trajectories to represent the characteristics of the beam and its propagation. On the other hand, the word plume was adopted to describe a multidimensional flow (or expansion) of a plasma or neutral gas cloud. Within the framework of these definitions, experiment categories included: (1) Neutral- and charged-particle beam propagation, with considerations extending to high powers and currents. (2) Evolution and dynamics of naturally occurring and man-made plasma and neutral gas clouds. In both categories, scientific interest focused on interactions with the ambient geoplasma and the evolution of particle densities, energy distribution functions, waves, and fields.

  15. 49 CFR 393.61 - Truck and truck tractor window construction.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in...

  16. 49 CFR 393.61 - Truck and truck tractor window construction.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 5 2011-10-01 2011-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in...

  17. 49 CFR 393.61 - Truck and truck tractor window construction.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 5 2012-10-01 2012-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in...

  18. 49 CFR 393.61 - Truck and truck tractor window construction.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 5 2014-10-01 2014-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in...

  19. 49 CFR 393.61 - Truck and truck tractor window construction.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 5 2013-10-01 2013-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in...

  20. 75 FR 2153 - Certificate of Alternative Compliance for the Tractor Tug FORTE

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ... SECURITY Coast Guard Certificate of Alternative Compliance for the Tractor Tug FORTE AGENCY: Coast Guard... was issued for the tractor tug FORTE as required by 33 U.S.C. 1605(c) and 33 CFR 81.18. DATES: The... Purpose The tractor tug FORTE will be used for offshore supply operations. The horizontal distance...

  1. 4-H Tractor Operator Program Teaches Employability Skills and Safety to Youth

    ERIC Educational Resources Information Center

    Barrett, Debra K.

    2013-01-01

    For Michigan State University Extension, the Berrien County 4-H Tractor Operator Program has provided tractor safety education to teens for over 30 years. The certification training satisfies current requirements for operation of a 20 PTO HP or greater agricultural tractor by 14- and 15-year-old youth employed on property "not" owned,…

  2. Energetic Beam Processing of Silicon to Engineer Optoelectronically Active Defects

    NASA Astrophysics Data System (ADS)

    Recht, Daniel

    This thesis explores ways to use ion implantation and nanosecond pulsed laser melting, both energetic beam techniques, to engineer defects in silicon. These defects are chosen to facilitate the use of silicon in optoelectronic applications for which its indirect bandgap is not ideal. Chapter 2 develops a kinetic model for the use of point defects as luminescence centers for light-emitting diodes and demonstrates an experimental procedure capable of high-throughput screening of the electroluminescent properties of such defects. Chapter 3 discusses the dramatic change in optical absorption observed in silicon highly supersaturated (i.e., hyperdoped) with the chalcogens sulfur, selenium, and tellurium and reports the first measurements of the optical absorption of such materials for photon energies greater than the bandgap of silicon. Chapter 3 examines the use of silicon hyperdoped with chalcogens in light detectors and concludes that while these devices display strong internal gain that is coupled to a particular type of surface defect, hyperdoping with chalcogens does not lead directly to measurable sub-bandgap photoconductivity. Chapter 4 considers the potential for Silicon to serve as the active material in an intermediate-band solar cell and reports experimental progress on two proposed approaches for hyperdoping silicon for this application. The main results of this chapter are the use of native-oxide etching to control the surface evaporation rate of sulfur from silicon and the first synthesis of monocrystalline silicon hyperdoped with gold.

  3. Creating a National Coalition to Address Tractor Overturn Fatalities.

    PubMed

    Tinc, P J; Ayers, P D; May, J J; Purschwitz, M A; Sorensen, J A

    2015-04-01

    Tractor overturns continue to be the leading cause of death on U.S. farms. While rollover protective structures (ROPS) are effective in preventing these fatalities, they are underutilized due to a number of barriers. Past programs in the U.S. and abroad have targeted this area of agricultural safety; however, a national program is not yet in place for U.S. farmers. This study seeks to build a national partnership to address tractor overturn fatalities by increasing the number of tractors with ROPS. A diverse, multisector steering committee has been organized and is working together using Whole System in a Room methods. This method brings together partners from nine stakeholder groups to identify and commit to a collaborative solution to the issue. PMID:26204786

  4. Tractor controls actuating force limits for Indian operators.

    PubMed

    Mehta, C R; Pandey, M M; Tiwari, P S; Gite, L P; Khadatkar, Abhijit

    2011-01-01

    In four-wheel tractors, proper design of controls is important for comfortable and safe operation of the tractor. The design involves location and dimensions of controls as well as strength limits for operating these controls. The present study was aimed to quantify human strength for operation of tractor controls and to recommend the maximum control actuating forces for normal operation of tractors based on strength capability of 3,423 Indian male agricultural workers. The 5th percentile values of strength parameters i.e. leg strength sitting (left and right), foot strength sitting (right), torque strength (both hands) sitting, push strength (left hand and right hand) sitting and pull strength (left hand and right hand) sitting of agricultural workers collected using a strength measurement set-up were taken into consideration for the study. It was recommended that the maximum actuating forces for normal operation of frequently operated brake and clutch pedals of tractors should not exceed 260 N and 125 N based on 5th percentile values of right and left leg strength of male agricultural workers, respectively. The maximum actuating force required in steering wheel operation should not exceed 51 N based on 5th percentile value of torque strength (both hands) sitting of workers. The maximum actuating forces required for operating frequently operated levers viz. gear selection, speed selection, hydraulic control and hand throttle of Indian tractors should not exceed 46 N, 46 N, 25 N and 25 N, respectively. It may be concluded that the maximum actuating force limits as given in Bureau of Indian Standards IS 10703 are very high as compared to the findings of the study based on strength data of Indian male operators, which highlight the need to revise the standard. PMID:21697615

  5. Status of LHC crab activity simulations and beam studies

    SciTech Connect

    Calaga,R.; Assman, R.; Barranco, J.; Barranco, J.; Calaga, R.; Caspers, F.; Ciapala, E.; De-Maria, R.; Koutchouk, J. P.; Linnecar, T.; Metral, E.; Morita, A.; Solyak, N.; Sun, Y.; Tomas, R.; Tuckmantel, J.; Weiler, T.; Zimmermann, F.

    2009-05-04

    The LHC crab cavity program is advancing rapidly towards a first prototype which is anticipated to be tested during the early stages of the LHC phase I upgrade and commissioning. The general project status and some aspects related to crab optics, collimation, aperture constraints, impedances, noise effects. beam transparency and machine protection critical for a safe and robust operation of LHC beams with crab cavities are addressed here.

  6. Mission Concepts and Operations for Asteroid Mitigation Involving Multiple Gravity Tractors

    NASA Technical Reports Server (NTRS)

    Foster, Cyrus; Bellerose, Julie; Jaroux, Belgacem; Mauro, David

    2012-01-01

    The gravity tractor concept is a proposed method to deflect an imminent asteroid impact through gravitational tugging over a time scale of years. In this study, we present mission scenarios and operational considerations for asteroid mitigation efforts involving multiple gravity tractors. We quantify the deflection performance improvement provided by a multiple gravity tractor campaign and assess its sensitivity to staggered launches. We next explore several proximity operation strategies to accommodate multiple gravity tractors at a single asteroid including formation-flying and mechanically-docked configurations. Finally, we utilize 99942 Apophis as an illustrative example to assess the performance of a multiple gravity tractor campaign.

  7. The rod of Aesculapios: John Haygarth (1740-1827) and Perkins' metallic tractors.

    PubMed

    Booth, Christopher

    2005-08-01

    James Gillray's cartoon Metallic Tractors, published in 1801, portrays Benjamin Perkins treating a boil on the nose of an alcoholic John Bull with a pair of metallic tractors. The tractors had been invented by his father, Elisha Perkins of Connecticut, and were supposed to relieve pain and other symptoms through the agency of animal magnetism. The tractors were revealed as nothing more than an expensive sham by Dr John Haygarth in Bath, who showed that wooden tractors were equally effective. Thus, he was one of the first to use a placebo in a single-blind clinical trial.

  8. A spatial cluster analysis of tractor overturns in Kentucky from 1960 to 2002

    USGS Publications Warehouse

    Saman, D.M.; Cole, H.P.; Odoi, A.; Myers, M.L.; Carey, D.I.; Westneat, S.C.

    2012-01-01

    Background: Agricultural tractor overturns without rollover protective structures are the leading cause of farm fatalities in the United States. To our knowledge, no studies have incorporated the spatial scan statistic in identifying high-risk areas for tractor overturns. The aim of this study was to determine whether tractor overturns cluster in certain parts of Kentucky and identify factors associated with tractor overturns. Methods: A spatial statistical analysis using Kulldorff's spatial scan statistic was performed to identify county clusters at greatest risk for tractor overturns. A regression analysis was then performed to identify factors associated with tractor overturns. Results: The spatial analysis revealed a cluster of higher than expected tractor overturns in four counties in northern Kentucky (RR = 2.55) and 10 counties in eastern Kentucky (RR = 1.97). Higher rates of tractor overturns were associated with steeper average percent slope of pasture land by county (p = 0.0002) and a greater percent of total tractors with less than 40 horsepower by county (p<0.0001). Conclusions: This study reveals that geographic hotspots of tractor overturns exist in Kentucky and identifies factors associated with overturns. This study provides policymakers a guide to targeted county-level interventions (e.g., roll-over protective structures promotion interventions) with the intention of reducing tractor overturns in the highest risk counties in Kentucky. ?? 2012 Saman et al.

  9. Actively triggered 4d cone-beam CT acquisition

    SciTech Connect

    Fast, Martin F.; Wisotzky, Eric; Oelfke, Uwe; Nill, Simeon

    2013-09-15

    Purpose: 4d cone-beam computed tomography (CBCT) scans are usually reconstructed by extracting the motion information from the 2d projections or an external surrogate signal, and binning the individual projections into multiple respiratory phases. In this “after-the-fact” binning approach, however, projections are unevenly distributed over respiratory phases resulting in inefficient utilization of imaging dose. To avoid excess dose in certain respiratory phases, and poor image quality due to a lack of projections in others, the authors have developed a novel 4d CBCT acquisition framework which actively triggers 2d projections based on the forward-predicted position of the tumor.Methods: The forward-prediction of the tumor position was independently established using either (i) an electromagnetic (EM) tracking system based on implanted EM-transponders which act as a surrogate for the tumor position, or (ii) an external motion sensor measuring the chest-wall displacement and correlating this external motion to the phase-shifted diaphragm motion derived from the acquired images. In order to avoid EM-induced artifacts in the imaging detector, the authors devised a simple but effective “Faraday” shielding cage. The authors demonstrated the feasibility of their acquisition strategy by scanning an anthropomorphic lung phantom moving on 1d or 2d sinusoidal trajectories.Results: With both tumor position devices, the authors were able to acquire 4d CBCTs free of motion blurring. For scans based on the EM tracking system, reconstruction artifacts stemming from the presence of the EM-array and the EM-transponders were greatly reduced using newly developed correction algorithms. By tuning the imaging frequency independently for each respiratory phase prior to acquisition, it was possible to harmonize the number of projections over respiratory phases. Depending on the breathing period (3.5 or 5 s) and the gantry rotation time (4 or 5 min), between ∼90 and 145

  10. 40 CFR 1037.630 - Special purpose tractors.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Special purpose tractors. 1037.630 Section 1037.630 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW HEAVY-DUTY MOTOR VEHICLES Special Compliance Provisions §...

  11. 40 CFR 1037.630 - Special purpose tractors.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... under § 1037.135: “THIS VEHICLE WAS CERTIFIED AS A VOCATIONAL TRACTOR UNDER 40 CFR 1037.630.”. (4) You... § 1037.631 and using an engine certified to the standards of 40 CFR part 1036 are deemed to fully conform... Section 1037.630 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

  12. 40 CFR 1037.630 - Special purpose tractors.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... under § 1037.135: “THIS VEHICLE WAS CERTIFIED AS A VOCATIONAL TRACTOR UNDER 40 CFR 1037.630.”. (4) You... § 1037.631 and using an engine certified to the standards of 40 CFR part 1036 are deemed to fully conform... Section 1037.630 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

  13. Math on the Job. Tractor-Trailer Driver.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. National Center for Research in Vocational Education.

    This booklet is intended to help mainstreamed mentally retarded, emotionally disturbed, or learning disabled high school students acquire a basic understanding of the responsibilities and working conditions of tractor-trailer drivers and to practice basic math skills necessary in the occupation. The first section provides a brief introduction to…

  14. Tractor Mechanic--Student Material. Competency Based Education Curriculum.

    ERIC Educational Resources Information Center

    McCann, Edward W.

    Developed to assist vocational agricultural mechanics students in learning to be tractor mechanics, this curriculum guide contains all the student competency sheets which comprise this competency-based curriculum. These competency sheets are categorized under sixteen instructional units. The first two units cover employment opportunities and…

  15. Plasma effects of active ion beam injections in the ionosphere at rocket altitudes

    NASA Technical Reports Server (NTRS)

    Arnoldy, R. L.; Cahill, L. J., Jr.; Kintner, P. M.; Moore, T. E.; Pollock, C. J.

    1992-01-01

    Data from ARCS rocket ion beam injection experiments are primarily discussed. There are three results from this series of active experiments that are of particular interest in space plasma physics. These are the transverse acceleration of ambient ions in the large beam volume, the scattering of beam ions near the release payload, and the possible acceleration of electrons very close to the plasma generator which produce intense high frequency waves. The ability of 100 ma ion beam injections into the upper E and F regions of the ionosphere to produce these phenomena appear to be related solely to the process by which the plasma release payload and the ion beam are neutralized. Since the electrons in the plasma release do not convect with the plasma ions, the neutralization of both the payload and beam must be accomplished by large field-aligned currents (milliamperes/square meter) which are very unstable to wave growth of various modes.

  16. Active fault tolerant control of a flexible beam

    NASA Astrophysics Data System (ADS)

    Bai, Yuanqiang; Grigoriadis, Karolos M.; Song, Gangbing

    2007-04-01

    This paper presents the development and application of an H∞ fault detection and isolation (FDI) filter and fault tolerant controller (FTC) for smart structures. A linear matrix inequality (LMI) formulation is obtained to design the full order robust H∞ filter to estimate the faulty input signals. A fault tolerant H∞ controller is designed for the combined system of plant and filter which minimizes the control objective selected in the presence of disturbances and faults. A cantilevered flexible beam bonded with piezoceramic smart materials, in particular the PZT (Lead Zirconate Titanate), in the form of a patch is used in the validation of the FDI filter and FTC controller design. These PZT patches are surface-bonded on the beam and perform as actuators and sensors. A real-time data acquisition and control system is used to record the experimental data and to implement the designed FDI filter and FTC. To assist the control system design, system identification is conducted for the first mode of the smart structural system. The state space model from system identification is used for the H∞ FDI filter design. The controller was designed based on minimization of the control effort and displacement of the beam. The residuals obtained from the filter through experiments clearly identify the fault signals. The experimental results of the proposed FTC controller show its e effectiveness for the vibration suppression of the beam for the faulty system when the piezoceramic actuator has a partial failure.

  17. Operators' perception of comfort in two tractor cabs.

    PubMed

    Ferrari, E; Cavallo, E

    2013-01-01

    Workspace characteristics affect the perceived comfort level of the operator and uncomfortable working conditions have been found to have a negative impact on productivity and safety. The comfort of the operator is increasingly recognized by manufacturers as a product's added value. Comfort can positively distinguish a product and increase its competitiveness. The concept of comfort is controversial, and a clear operational definition is missing. Nevertheless, it is widely accepted that comfort is a subjective phenomenon that can be evaluated by the final users. In this study, comfort aspects of the tractor workspace interior (i.e., the cab) were investigated. Users with various levels of expertise and two medium-power utility tractors of different brands were used in a 2 x 2 mixed-factorial experimental design. Participants were involved in a dynamic assessment of the cabs, and their opinions about the different workspaces were collected through a questionnaire. Additionally, objective measurements were taken on both tractors, and subjective data were compared with objective data. Results indicate significant differences in terms of the ease of locating and operating the controls (i.e., rear-mounted three-point linkage, hydraulic system, and power take-off), the ease of starting the tractor, the ease exiting the cab, the required level of concentration in executing the tasks, the adequacy of lateral visibility from the driving station, and the level of noise at the operator's position. This article provides guidance for improving the comfort of tractor workspace interiors. Agricultural machinery manufactures would benefit from research results, differentiating themselves from competitors. PMID:23600166

  18. Test for the integrity of environmental tractor cab filtration systems.

    PubMed

    Moyer, Ernest S; Heitbrink, William A; Jensen, Paul A

    2005-10-01

    Cab filtration systems can be used to protect vehicle operators from hazardous air contaminants. In a cab filtration system, a fan draws air through filters and pressurizes the cab with this filtered air. This article describes the application of a low-cost, optical particle counter to evaluate the performance of tractor cab filtration systems. The tractors were equipped with environmental enclosures to protect the operators from pesticide exposures that occur during air blast spraying in orchards. Prior to testing, all environmental tractor cabs underwent a complete maintenance overhaul followed by a careful inspection by the manufacturer's field representative. As part of this maintenance effort, 13 tractors with cab filtration systems were tested in an enclosure. A Met One model 227B two-channel optical particle counter was used to measure the aerosol concentration outside and inside the cab. Ambient aerosol and/or aerosol generated by burning incense sticks were used to challenge the stationary cab filtration system in an enclosure. The ratio of the outside to inside concentration (Co/Ci) is the exposure reduction attained by the cab system. Alternatively, the inside concentration divided by the outside concentration times 100 (Ci/Co x 100) gives the percent penetration. All 13 tractors were tested for leak sites. Leak sites were identified and sealed. This process was repeated until each cab showed an exposure reduction ratio Co/Ci of at least 50 (aerosol penetration into the cab Ci/Co x 100 was less than 2%) at the 0.3-0.5 microm particle size interval.

  19. Operators' perception of comfort in two tractor cabs.

    PubMed

    Ferrari, E; Cavallo, E

    2013-01-01

    Workspace characteristics affect the perceived comfort level of the operator and uncomfortable working conditions have been found to have a negative impact on productivity and safety. The comfort of the operator is increasingly recognized by manufacturers as a product's added value. Comfort can positively distinguish a product and increase its competitiveness. The concept of comfort is controversial, and a clear operational definition is missing. Nevertheless, it is widely accepted that comfort is a subjective phenomenon that can be evaluated by the final users. In this study, comfort aspects of the tractor workspace interior (i.e., the cab) were investigated. Users with various levels of expertise and two medium-power utility tractors of different brands were used in a 2 x 2 mixed-factorial experimental design. Participants were involved in a dynamic assessment of the cabs, and their opinions about the different workspaces were collected through a questionnaire. Additionally, objective measurements were taken on both tractors, and subjective data were compared with objective data. Results indicate significant differences in terms of the ease of locating and operating the controls (i.e., rear-mounted three-point linkage, hydraulic system, and power take-off), the ease of starting the tractor, the ease exiting the cab, the required level of concentration in executing the tasks, the adequacy of lateral visibility from the driving station, and the level of noise at the operator's position. This article provides guidance for improving the comfort of tractor workspace interiors. Agricultural machinery manufactures would benefit from research results, differentiating themselves from competitors.

  20. A mask for high-intensity heavy-ion beams in the MAYA active target

    NASA Astrophysics Data System (ADS)

    Rodríguez-Tajes, C.; Pancin, J.; Damoy, S.; Roger, T.; Babo, M.; Caamaño, M.; Farget, F.; Grinyer, G. F.; Jacquot, B.; Pérez-Loureiro, D.; Ramos, D.; Suzuki, D.

    2014-12-01

    The use of high-intensity and/or heavy-ion beams in active targets and time-projection chambers is often limited by the strong ionization produced by the beam. Besides the difficulties associated with the saturation of the detector and electronics, beam-related signals may hide the physical events of interest or reduce the detector performance. In addition, space-charge effects may deteriorate the homogeneity of the electric drift field and distort the subsequent reconstruction of particle trajectories. In anticipation of future projects involving such conditions, a dedicated beam mask has been developed and tested in the MAYA active target. Experimental results with a 136Xe beam are presented.

  1. Safety status of farm tractors that operate on public highways in four rural Kentucky counties.

    PubMed

    Cole, H P; Piercy, L R; Heinz, K L; Westneat, S C; Arrowsmith, H E; Raymond, K M

    2009-07-01

    Kentucky FFA students inspected 153 farm tractors for safety features that prevent operator injuries during tractor overturns, highway collisions, runovers, and power take-off (PTO) entanglements. Tractor mean age was 23.6 years (SD = 20.9). Rollover protective structures (ROPS) were present on 50.66% of tractors, but only 33.33% of these had functional seatbelts. Loose and damaged seats were found on 30.46% of tractors. In 38.99% of cases, tractor rear-wheel fenders exposed operators to moving tractor tires, and 48.67% of tractors had dangerously worn or damaged tires. Tractors with a narrow front-end stance comprised 16.11% of the total. Only 53.06% of the tractors had starters with secure hard cover by-pass starting shields that fully covered the starter terminals, and 37.37% had fully exposed terminals with no cover. PTO master shields with all parts present and undamaged were present on only 29.27% of the tractors, and in 39.02% of cases the entire shield was missing. Only 44.67% of the tractors had properly mounted and fully functional mounting and dismounting access steps and handholds. SMV emblems were missing on 53.64% of tractors and in the proper place and condition in only 25.83% of cases. Tractors with properly mounted and fully functional head and tail lights comprised 40.94% of the sample, and tractors with no functional lights comprised 24.16%. Properly mounted, clean, and functional rearview mirrors were present on only 19.87% of the tractors, and 69.54% had no rearview mirrors. The project increased farming and non-farming students' awareness of tractor safety issues, provided empirical data about the safety status of a sample of tractors that frequently travel public highways in four rural Kentucky farming counties, and promoted dialog about these issues with adult farmers and other community members with whom the students interacted. PMID:19728545

  2. Microwave and Beam Activation of Nanostructured Catalysts for Environmentally Friendly, Energy Efficient Heavy Crude Oil Processing

    SciTech Connect

    2009-03-01

    This factsheet describes a study whose goal is initial evaluation and development of energy efficient processes which take advantage of the benefits offered by nanostructured catalysts which can be activated by microwave, RF, or radiation beams.

  3. SU-E-J-49: Distal Edge Activity Fall Off Of Proton Therapy Beams

    SciTech Connect

    Elmekawy, A; Ewell, L; Butuceanu, C; Zhu, L

    2014-06-01

    Purpose: To characterize and quantify the distal edge activity fall off, created in a phantom by a proton therapy beam Method and Materials: A 30x30x10cm polymethylmethacrylate phantom was irradiated with a proton therapy beam using different ranges and beams. The irradiation volume is approximated by a right circular cylinder of diameter 7.6cm and varying lengths. After irradiation, the phantom was scanned via a Philips Gemini Big Bore™ PET-CT for isotope activation. Varian Eclipse™ treatment planning system as well as ImageJ™ were used to analyze the resulting PET and CT scans. The region of activity within the phantom was longitudinally measured as a function of PET slice number. Dose estimations were made via Monte Carlo (GATE) simulation. Results: For both the spread out Bragg peak (SOBP) and the mono-energetic pristine Bragg peak proton beams, the proximal activation rise was steep: average slope −0.735 (average intensity/slice number) ± 0.091 (standard deviation) for the pristine beams and −1.149 ± 0.117 for the SOBP beams. In contrast, the distal fall offs were dissimilar. The distal fall off in activity for the pristine beams was fit well by a linear curve: R{sup 2} (Pierson Product) was 0.9968, 0.9955 and 0.9909 for the 13.5, 17.0 and 21.0cm range beams respectively. The good fit allows for a slope comparison between the different ranges. The slope varied as a function of range from 1.021 for the 13.5cm beam to 0.8407 (average intensity/slice number) for the 21.0cm beam. This dependence can be characterized: −0.0234(average intensity/slice number/cm range). For the SOBP beams, the slopes were significantly less and were also less linear: average slope 0.2628 ± 0.0474, average R{sup 2}=0.9236. Conclusion: The distal activation fall off edge for pristine proton beams was linear and steep. The corresponding quantities for SOBP beams were shallower and less linear. Philips has provided support for this work.

  4. Electron-beam activated thermal sputtering of thermoelectric materials

    SciTech Connect

    Wu Jinsong; Dravid, Vinayak P.; He Jiaqing; Han, Mi-Kyung; Sootsman, Joseph R.; Girard, Steven; Arachchige, Indika U.; Kanatzidis, Mercouri G.

    2011-08-15

    Thermoelectricity and Seebeck effect have long been observed and validated in bulk materials. With the development of advanced tools of materials characterization, here we report the first observation of such an effect in the nanometer scale: in situ directional sputtering of several thermoelectric materials inside electron microscopes. The temperature gradient introduced by the electron beam creates a voltage-drop across the samples, which enhances spontaneous sputtering of specimen ions. The sputtering occurs along a preferential direction determined by the direction of the temperature gradient. A large number of nanoparticles form and accumulate away from the beam location as a result. The sputtering and re-crystallization are found to occur at temperatures far below the melting points of bulk materials. The sputtering occurs even when a liquid nitrogen cooling holder is used to keep the overall temperature at -170 deg. C. This unique phenomenon that occurred in the nanometer scale may provide useful clues to understanding the mechanism of thermoelectric effect.

  5. Electron-beam activated thermal sputtering of thermoelectric materials.

    SciTech Connect

    Wu, J.; He, J.; Han, M-K.; Sootsman, J. R.; Girard, S.; Arachchige, I. U.; Kanatzidis, M. G.; Dravid, V. P.

    2011-08-01

    Thermoelectricity and Seebeck effect have long been observed and validated in bulk materials. With the development of advanced tools of materials characterization, here we report the first observation of such an effect in the nanometer scale: in situ directional sputtering of several thermoelectric materials inside electron microscopes. The temperature gradient introduced by the electron beam creates a voltage-drop across the samples, which enhances spontaneous sputtering of specimen ions. The sputtering occurs along a preferential direction determined by the direction of the temperature gradient. A large number of nanoparticles form and accumulate away from the beam location as a result. The sputtering and re-crystallization are found to occur at temperatures far below the melting points of bulk materials. The sputtering occurs even when a liquid nitrogen cooling holder is used to keep the overall temperature at -170 C. This unique phenomenon that occurred in the nanometer scale may provide useful clues to understanding the mechanism of thermoelectric effect.

  6. Personal noise exposures of operators of agricultural tractors.

    PubMed

    Aybek, Ali; Kamer, H Atil; Arslan, Selçuk

    2010-03-01

    Approximately one million agricultural tractors are used in Turkey for crop production and about one-third of the population lives in rural areas. The objectives of this study were to determine sound pressure levels, A-weighted sound pressure levels, and the permissible exposure time for tractors without cabins, field-installed cabins, and original cabins at ear level of agricultural tractor operators for following machines: plows, cultivators, top soil cultivators, rotary tillers, tool combinations (harrow+roller), mechanical drills, pneumatic drills, chemical applicators, fertilizer applicators, drum mowers, balers, and forage harvesters. Variance analyses showed that type of operation, type of cabins, and operation x cabin interactions were statistically significant (P<0.01) both for sound pressure levels and equivalent (A-weighted) sound pressure levels. The use of original cabins had a greater effect in decreasing average sound pressures and resulted in more efficient noise insulation, especially at higher center frequencies compared to field-installed cabins whereas field-installed cabins proved to be more favorable compared to tractors without cabins. Sound pressure levels at 4000Hz center frequency was reduced 2-13dB and 4-18dB by using a field-installed cabin and an original cabin, respectively. The measured A-weighted equivalent sound pressure levels were compared to the threshold limit level, and was concluded that depending on the cabin types used, the operators could usually work from 4 to 6h a day without suffering from noise induced inconveniences while 2-3h is permissible for plowing and forage harvesting on tractors without cabins. Due to timeliness considerations in agricultural machine operations, a farmer would not be willing to interrupt the operation based on permissible exposure time set by the standards. Based on the findings of this study, particularly an original cabin is recommended to reduce machine-induced noise below the danger limit

  7. Linear tractor dry coal extrusion pump

    SciTech Connect

    Sprouse, Kenneth M.; Matthews, David R.

    2011-10-18

    A pump for transporting particulate material includes an inlet, an outlet, a passageway, a first and second load beam, a first and second scraper seal, and a first and second drive assembly. The inlet introduces the particulate material into the passageway and the outlet expels the particulate material from the passageway. The passageway is defined by a first belt assembly and a second belt assembly that are opposed to each other. The first and second load beams are positioned within the first belt assembly and the second belt assembly, respectively. The first scraper seal and a second scraper seal are positioned proximate the passageway and the outlet. The first drive assembly is positioned within an interior section of the first belt assembly and drives the first belt assembly and the second drive assembly is positioned within an interior section of the second belt assembly and drives the second belt assembly.

  8. Linear tractor dry coal extrusion pump

    DOEpatents

    Sprouse, Kenneth M.; Matthews, David R.

    2008-06-17

    A pump for transporting particulate material includes an inlet, an outlet, a passageway, a first and second load beam, a first and second scraper seal, and a first and second drive assembly. The inlet introduces the particulate material into the passageway and the outlet expels the particulate material from the passageway. The passageway is defined by a first belt assembly and a second belt assembly that are opposed to each other. The first and second load beams are positioned within the first belt assembly and the second belt assembly, respectively. The first scraper seal and a second scraper seal are positioned proximate the passageway and the outlet. The first drive assembly is positioned within an interior section of the first belt assembly and drives the first belt assembly and the second drive assembly is positioned within an interior section of the second belt assembly and drives the second belt assembly.

  9. Active Plasma Lensing for Relativistic Laser-Plasma-Accelerated Electron Beams.

    PubMed

    van Tilborg, J; Steinke, S; Geddes, C G R; Matlis, N H; Shaw, B H; Gonsalves, A J; Huijts, J V; Nakamura, K; Daniels, J; Schroeder, C B; Benedetti, C; Esarey, E; Bulanov, S S; Bobrova, N A; Sasorov, P V; Leemans, W P

    2015-10-30

    Compact, tunable, radially symmetric focusing of electrons is critical to laser-plasma accelerator (LPA) applications. Experiments are presented demonstrating the use of a discharge-capillary active plasma lens to focus 100-MeV-level LPA beams. The lens can provide tunable field gradients in excess of 3000 T/m, enabling cm-scale focal lengths for GeV-level beam energies and allowing LPA-based electron beams and light sources to maintain their compact footprint. For a range of lens strengths, excellent agreement with simulation was obtained. PMID:26565471

  10. Active Plasma Lensing for Relativistic Laser-Plasma-Accelerated Electron Beams

    NASA Astrophysics Data System (ADS)

    van Tilborg, J.; Steinke, S.; Geddes, C. G. R.; Matlis, N. H.; Shaw, B. H.; Gonsalves, A. J.; Huijts, J. V.; Nakamura, K.; Daniels, J.; Schroeder, C. B.; Benedetti, C.; Esarey, E.; Bulanov, S. S.; Bobrova, N. A.; Sasorov, P. V.; Leemans, W. P.

    2015-10-01

    Compact, tunable, radially symmetric focusing of electrons is critical to laser-plasma accelerator (LPA) applications. Experiments are presented demonstrating the use of a discharge-capillary active plasma lens to focus 100-MeV-level LPA beams. The lens can provide tunable field gradients in excess of 3000 T /m , enabling cm-scale focal lengths for GeV-level beam energies and allowing LPA-based electron beams and light sources to maintain their compact footprint. For a range of lens strengths, excellent agreement with simulation was obtained.

  11. Pre-turbocharger alcohol fumigation in a diesel tractor

    SciTech Connect

    Sullivan, N.W.; Bashford, L.L.

    1981-01-01

    An M and W alcohol Conversion kit was installed on an AC 7040 turbocharged diesel tractor. The unit was dynamometer tested with 100 proof and 185 proof ethanol. This system injects alcohol into the intake air stream and permits reduction of diesel fuel-consumption by 10-15 percent. Turbocharger blade wear, as well as other problems with the system, are presented. 8 refs.

  12. Application of a passive/active autoparametric cantilever beam absorber with PZT actuator for Duffing systems

    NASA Astrophysics Data System (ADS)

    Silva-Navarro, G.; Abundis-Fong, H. F.; Vazquez-Gonzalez, B.

    2013-04-01

    An experimental investigation is carried out on a cantilever-type passive/active autoparametric vibration absorber, with a PZT patch actuator, to be used in a primary damped Duffing system. The primary system consists of a mass, viscous damping and a cubic stiffness provided by a soft helical spring, over which is mounted a cantilever beam with a PZT patch actuator actively controlled to attenuate harmonic and resonant excitation forces. With the PZT actuator on the cantilever beam absorber, cemented to the base of the beam, the auto-parametric vibration absorber is made active, thus enabling the possibility to control the effective stiffness and damping associated to the passive absorber and, as a consequence, the implementation of an active vibration control scheme able to preserve, as possible, the autoparametric interaction as well as to compensate varying excitation frequencies and parametric uncertainty. This active vibration absorber employs feedback information from a high resolution optical encoder on the primary Duffing system and an accelerometer on the tip beam absorber, a strain gage on the base of the beam, feedforward information from the excitation force and on-line computations from the nonlinear approximate frequency response, parameterized in terms of a proportional gain provided by a voltage input to the PZT actuator, thus modifying the closed-loop dynamic stiffness and providing a mechanism to asymptotically track an optimal, robust and stable attenuation solution on the primary Duffing system. Experimental results are included to describe the dynamic and robust performance of the overall closed-loop system.

  13. Anti-angiogenic activity in metastasis of human breast cancer cells irradiated by a proton beam

    NASA Astrophysics Data System (ADS)

    Lee, Kyu-Shik; Shin, Jin-Sun; Nam, Kyung-Soo; Shon, Yun-Hee

    2012-07-01

    Angiogenesis is an essential process of metastasis in human breast cancer. We investigated the effects of proton beam irradiation on angiogenic enzyme activities and their expressions in MCF-7 human breast cancer cells. The regulation of angiogenic regulating factors, of transforming growth factor- β (TGF- β) and of vesicular endothelial growth factor (VEGF) expression in breast cancer cells irradiated with a proton beam was studied. Aromatase activity and mRNA expression, which is correlated with metastasis, were significantly decreased by irradiation with a proton beam in a dose-dependent manner. TGF- β and VEGF transcriptions were also diminished by proton beam irradiation. In contrast, transcription of tissue inhibitors of matrix metalloproteinases (TIMPs), also known as biological inhibitors of matrix metalloproteinases (MMPs), was dose-dependently enhanced. Furthermore, an increase in the expression of TIMPs caused th MMP-9 activity to be diminished and the MMP-9 and the MMP-2 expressions to be decreased. These results suggest that inhibition of angiogenesis by proton beam irradiation in breast cancer cells is closely related to inhibitions of aromatase activity and transcription and to down-regulation of TGF- β and VEGF transcription.

  14. Beams, brightness, and background: Using active spectroscopy techniques for precision measurements in fusion plasma research

    SciTech Connect

    Thomas, Dan M.

    2012-05-15

    The use of an injected neutral beam-either a dedicated diagnostic beam or the main heating beams-to localize and enhance plasma spectroscopic measurements can be exploited for a number of key physics issues in magnetic confinement fusion research, yielding detailed profile information on thermal and fast ion parameters, the radial electric field, plasma current density, and turbulent transport. The ability to make these measurements has played a significant role in much of our recent progress in the scientific understanding of fusion plasmas. The measurements can utilize emission from excited state transitions either from plasma ions or from the beam atoms themselves. The primary requirement is that the beam 'probe' interacts with the plasma in a known fashion. Advantages of active spectroscopy include high spatial resolution due to the enhanced localization of the emission and the use of appropriate imaging optics, background rejection through the appropriate modulation and timing of the beam and emission collection/detection system, and the ability of the beam to populate emitter states that are either nonexistent or too dim to utilize effectively in the case of standard or passive spectroscopy. In addition, some active techniques offer the diagnostician unique information because of the specific quantum physics responsible for the emission. This paper will describe the general principles behind a successful active spectroscopic measurement, emphasize specific techniques that facilitate the measurements and include several successful examples of their implementation, briefly touching on some of the more important physics results. It concludes with a few remarks about the relevance and requirements of active spectroscopic techniques for future burning plasma experiments.

  15. Induction of antioxidant enzyme activity and lipid peroxidation level in ion-beam-bombarded rice seeds

    NASA Astrophysics Data System (ADS)

    Semsang, Nuananong; Yu, LiangDeng

    2013-07-01

    Low-energy ion beam bombardment has been used to mutate a wide variety of plant species. To explore the indirect effects of low-energy ion beam on biological damage due to the free radical production in plant cells, the increase in antioxidant enzyme activities and lipid peroxidation level was investigated in ion-bombarded rice seeds. Local rice seeds were bombarded with nitrogen or argon ion beams at energies of 29-60 keV and ion fluences of 1 × 1016 ions cm-2. The activities of the antioxidant enzymes; superoxide dismutase (SOD), catalase (CAT), ascorbate peroxidase (APX), dehydroascorbate reductase (DHAR), glutathione reductase (GR), glutathione S-transferase (GST) and lipid peroxidation level were assayed in the germinated rice seeds after ion bombardment. The results showed most of the enzyme activities and lipid peroxidation levels in both the argon and nitrogen bombarded samples were higher than those in the natural control. N-ion bombardment could induce higher levels of antioxidant enzyme activities in the rice samples than the Ar-ion bombardment. Additional effects due to the vacuum condition were found to affect activities of some antioxidant enzymes and lipid peroxidation level. This study demonstrates that ion beam bombardment and vacuum condition could induce the antioxidant enzyme activity and lipid peroxidation level which might be due to free radical production in the bombarded rice seeds.

  16. 29 CFR 1928.52 - Protective frames for wheel-type agricultural tractors-test procedures and performance requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CFR 1928.51. (b) Types of tests. All protective frames for wheel-type agricultural tractors shall be... load is applied. (ii) The following definitions shall apply: W = Tractor weight (see 29 CFR 1928.51(a... conditions shall be met: (A) The protective frame and tractor shall be tested at the weight defined by 29...

  17. Surface diffusion activation energy determination using ion beam microtexturing

    NASA Technical Reports Server (NTRS)

    Rossnagel, S. M.; Robinson, R. S.

    1982-01-01

    The activation energy for impurity atom (adatom) surface diffusion can be determined from the temperature dependence of the spacing of sputter cones. These cones are formed on the surface during sputtering while simultaneously adding impurities. The impurities form clusters by means of surface diffusion, and these clusters in turn initiate cone formation. Values are given for the surface diffusion activation energies for various materials on polycrystalline Cu, Al, Pb, Au, and Ni. The values for different impurity species on each of these substrates are approximately independent of impurity species within the experimental uncertainty, suggesting the absence of strong chemical bonding effects on the diffusion.

  18. A Tractor or an Automobile? A 1920s Farm Family Faces a Decision.

    ERIC Educational Resources Information Center

    Kunze, Joel P.

    1991-01-01

    Outlines a lesson plan in which students role play a 1920s farm family deciding whether to buy an automobile or a tractor. Other students act as automobile and tractor sales groups. Explains how the lesson illuminates relationships between technological advance and social history. Includes handouts identifying benefits of purchasing cars or…

  19. Active terahertz beam steering by photo-generated graded index gratings in thin semiconductor films.

    PubMed

    Steinbusch, T P; Tyagi, H K; Schaafsma, M C; Georgiou, G; Gómez Rivas, J

    2014-11-01

    We demonstrate active beam steering of terahertz radiation using a photo-excited thin layer of gallium arsenide. A constant gradient of phase discontinuity along the interface is introduced by an spatially inhomogeneous density of free charge carriers that are photo-generated in the GaAs with an optical pump. The optical pump has been spatially modulated to form the shape of a planar blazed grating. The phase gradient leads to an asymmetry between the +1 and -1 transmission diffracted orders of more than a factor two. Optimization of the grating structure can lead to an asymmetry of more than one order of magnitude. Similar to metasurfaces made of plasmonic antennas, the photo-generated grating is a planar structure that can achieve large beam steering efficiency. Moreover, the photo-generation of such structures provides a platform for active THz beam steering. PMID:25401807

  20. Design and implementation of a GPS guidance system for agricultural tractors using augmented reality technology.

    PubMed

    Santana-Fernández, Javier; Gómez-Gil, Jaime; del-Pozo-San-Cirilo, Laura

    2010-01-01

    Current commercial tractor guidance systems present to the driver information to perform agricultural tasks in the best way. This information generally includes a treated zones map referenced to the tractor's position. Unlike actual guidance systems where the tractor driver must mentally associate treated zone maps and the plot layout, this paper presents a guidance system that using Augmented Reality (AR) technology, allows the tractor driver to see the real plot though eye monitor glasses with the treated zones in a different color. The paper includes a description of the system hardware and software, a real test done with image captures seen by the tractor driver, and a discussion predicting that the historical evolution of guidance systems could involve the use of AR technology in the agricultural guidance and monitoring systems.

  1. On the optimum ride control of a stochastic model of a tractor-semitrailer vehicle

    NASA Astrophysics Data System (ADS)

    ElMadany, M. M.; Samaha, M. E.

    1992-07-01

    A systematic approach based on stochastic optimal control and estimation theories for the optimal design of active suspension systems for a tractor-semitrailer vehicle is presented. The vehicle-road system dynamics combined with the human perception of random vibrations are cast in the standard linear quadratic Gaussian format. The time delays of the stochastic excitation process of the multi-axled vehicle are represented by a first order Padé approximation. The optimal controller/observer is derived which minimizes the mean-squared values of performance variables reflecting the human comfort, cargo safety, suspension working space, roadholding ability and control forces. The advantages of optimally controlled suspension systems over their passive counterparts are indicated.

  2. Attosecond beamline with actively stabilized and spatially separated beam paths.

    PubMed

    Huppert, M; Jordan, I; Wörner, H J

    2015-12-01

    We describe a versatile and compact beamline for attosecond spectroscopy. The setup consists of a high-order harmonic source followed by a delay line that spatially separates and then recombines the extreme-ultraviolet (XUV) and residual infrared (IR) pulses. The beamline introduces a controlled and actively stabilized delay between the XUV and IR pulses on the attosecond time scale. A new active-stabilization scheme combining a helium-neon-laser and a white-light interferometer minimizes fluctuations and allows to control delays accurately (26 as rms during 1.5 h) over long time scales. The high-order-harmonic-generation region is imaged via optical systems, independently for XUV and IR, into an interaction volume to perform pump-probe experiments. As a consequence of the spatial separation, the pulses can be independently manipulated in intensity, polarization, and frequency content. The beamline can be combined with a variety of detectors for measuring attosecond dynamics in gases, liquids, and solids.

  3. Attosecond beamline with actively stabilized and spatially separated beam paths

    NASA Astrophysics Data System (ADS)

    Huppert, M.; Jordan, I.; Wörner, H. J.

    2015-12-01

    We describe a versatile and compact beamline for attosecond spectroscopy. The setup consists of a high-order harmonic source followed by a delay line that spatially separates and then recombines the extreme-ultraviolet (XUV) and residual infrared (IR) pulses. The beamline introduces a controlled and actively stabilized delay between the XUV and IR pulses on the attosecond time scale. A new active-stabilization scheme combining a helium-neon-laser and a white-light interferometer minimizes fluctuations and allows to control delays accurately (26 as rms during 1.5 h) over long time scales. The high-order-harmonic-generation region is imaged via optical systems, independently for XUV and IR, into an interaction volume to perform pump-probe experiments. As a consequence of the spatial separation, the pulses can be independently manipulated in intensity, polarization, and frequency content. The beamline can be combined with a variety of detectors for measuring attosecond dynamics in gases, liquids, and solids.

  4. Attosecond beamline with actively stabilized and spatially separated beam paths.

    PubMed

    Huppert, M; Jordan, I; Wörner, H J

    2015-12-01

    We describe a versatile and compact beamline for attosecond spectroscopy. The setup consists of a high-order harmonic source followed by a delay line that spatially separates and then recombines the extreme-ultraviolet (XUV) and residual infrared (IR) pulses. The beamline introduces a controlled and actively stabilized delay between the XUV and IR pulses on the attosecond time scale. A new active-stabilization scheme combining a helium-neon-laser and a white-light interferometer minimizes fluctuations and allows to control delays accurately (26 as rms during 1.5 h) over long time scales. The high-order-harmonic-generation region is imaged via optical systems, independently for XUV and IR, into an interaction volume to perform pump-probe experiments. As a consequence of the spatial separation, the pulses can be independently manipulated in intensity, polarization, and frequency content. The beamline can be combined with a variety of detectors for measuring attosecond dynamics in gases, liquids, and solids. PMID:26724005

  5. Hours of service violations among tractor-trailer drivers.

    PubMed

    Hertz, R P

    1991-02-01

    Federal regulation limits interstate truck drivers to 10 hours of driving after an 8-hour off-duty period. The need for enforcing these limits is supported by research showing that long driving hours is a risk factor for tractor-trailer crashes. To estimate the percentage of hours of service violators among long-haul tractor-trailer drivers, truck drivers were interviewed at an inspection site in Spokane, Washington and later observed arriving at inspection sites in either Moorhead or Worthington, Minnesota (approximately 1,200 miles). The sample used for the calculation of violators consisted of truckers driving alone who reportedly did not plan to make an interim pickup or delivery stop prior to arrival in Minnesota. The percentages of drivers violating the hours of service rules by more than one hour at average trip speeds ranging from 35 mph to 65 mph are presented. Assuming that the drivers averaged 40 mph over the complete course of the trip segment, including stopped time, 90% were in violation by more than one hour. Assuming that they averaged 50 mph, 51% were in violation by more than one hour. These speed assumptions are based on findings in the current study that team drivers averaged 38 mph, fleet managers' reports of scheduling single drivers at trip speeds of 45 mph to 47 mph, and reports in the literature that loaded tractor-trailers average 41 mph over flat terrain. Although the true percentage cannot be determined without knowing actual trip speeds, the estimated range of violators at probable speeds of 40 mph and 50 mph points to a substantial problem.

  6. Defective equipment and tractor-trailer crash involvement.

    PubMed

    Jones, I S; Stein, H S

    1989-10-01

    The role of defective equipment in large truck crashes on interstate highways in Washington State was investigated using a case-control study design. For each large truck involved in a crash, three trucks were randomly selected from the traffic stream at the same time and place as the crash, but one week later both crash and comparison trucks were inspected by Commercial Vehicle Enforcement officers of the Washington State Patrol. The effects of truck equipment condition, truck operating characteristics (carrier type, carrier operation, and truck load), and driver characteristics (driver age, hours of driving) on crash involvement were analyzed by comparing their relative frequency among crash-involved and comparison sample tractor-trailers. A logistic regression model was used to estimate the adjusted odds ratio for each factor. Overall, 77% of tractor-trailers in crashes and 66% of those not involved in crashes had defective equipment warranting a citation. Forty-one percent in crashes had defective equipment warranting taking the truck out of service, and 31% not in crashes had these defects. Brake defects were the most common type and were found in 56% of tractor-trailers in crashes; steering equipment defects were found in 21%. The relative risk of crash involvement for trucks with brake defects was about one and one-half times that for trucks without brake defects. For trucks with steering defects, the relative risk of crash involvement was at least twice that for trucks with steering defects, the relative risk of crash involvement was at least twice that for trucks without defects, and the risk increased substantially for trucks with out-of-service steering defects.

  7. Engineering catalytic activity via ion beam bombardment of catalyst supports for vertically aligned carbon nanotube growth

    DOE PAGES

    Islam, A. E.; Zakharov, D.; Stach, E. A.; Nikoleav, P.; Amama, P. B.; Sargent, G.; Saber, S.; Huffman, D.; Erford, M.; Semiatin, S. L.; et al

    2015-09-16

    Carbon nanotube growth depends on the catalytic activity of metal nanoparticles on alumina or silica supports. The control on catalytic activity is generally achieved by variations in water concentration, carbon feed, and sample placement on a few types of alumina or silica catalyst supports obtained via thin film deposition. We have recently expanded the choice of catalyst supports by engineering inactive substrates like c-cut sapphire via ion beam bombardment. The deterministic control on the structure and chemistry of catalyst supports obtained by tuning the degree of beam-induced damage have enabled better regulation of the activity of Fe catalysts only inmore » the ion beam bombarded areas and hence enabled controllable super growth of carbon nanotubes. A wide range of surface characterization techniques were used to monitor the catalytically active surface engineered via ion beam bombardment. The proposed method offers a versatile way to control carbon nanotube growth in patterned areas and also enhances the current understanding of the growth process. As a result, with the right choice of water concentration, carbon feed and sample placement, engineered catalyst supports may extend the carbon nanotube growth yield to a level that is even higher than the ones reported here, and thus offers promising applications of carbon nanotubes in electronics, heat exchanger, and energy storage.« less

  8. Engineering catalytic activity via ion beam bombardment of catalyst supports for vertically aligned carbon nanotube growth

    SciTech Connect

    Islam, A. E.; Zakharov, D.; Stach, E. A.; Nikoleav, P.; Amama, P. B.; Sargent, G.; Saber, S.; Huffman, D.; Erford, M.; Semiatin, S. L.; Maruyama, B.

    2015-09-16

    Carbon nanotube growth depends on the catalytic activity of metal nanoparticles on alumina or silica supports. The control on catalytic activity is generally achieved by variations in water concentration, carbon feed, and sample placement on a few types of alumina or silica catalyst supports obtained via thin film deposition. We have recently expanded the choice of catalyst supports by engineering inactive substrates like c-cut sapphire via ion beam bombardment. The deterministic control on the structure and chemistry of catalyst supports obtained by tuning the degree of beam-induced damage have enabled better regulation of the activity of Fe catalysts only in the ion beam bombarded areas and hence enabled controllable super growth of carbon nanotubes. A wide range of surface characterization techniques were used to monitor the catalytically active surface engineered via ion beam bombardment. The proposed method offers a versatile way to control carbon nanotube growth in patterned areas and also enhances the current understanding of the growth process. As a result, with the right choice of water concentration, carbon feed and sample placement, engineered catalyst supports may extend the carbon nanotube growth yield to a level that is even higher than the ones reported here, and thus offers promising applications of carbon nanotubes in electronics, heat exchanger, and energy storage.

  9. Preliminary results, obtained by using a proton beam, for an active scanning system to installed on the KHIMA

    NASA Astrophysics Data System (ADS)

    Kim, Chang Hyeuk; Lee, Hwa-Ryun; Jang, Sea Duk; Kim, Hyunyong; Hahn, Garam; Kim, Jeong Hwan; Jang, Hong Suk; Park, Dong Wook; Hwang, Won Taek; Yang, Tae-Keun

    2015-08-01

    The active scanning technique is a pencil beam delivery method in particle therapy. The active scanning beam delivery system consists of a beam scanner, beam monitor, energy modulator, and related programs, such as the irradiation control and planning programs. A proposed prototype active scanning system was designed and installed on MC-50 at the Korea Institute of Radiological and Medical Science (KIRAMS) with a 45-MeV proton beam. The laminated magnetic yoke of the scanning magnet supported fast ramping. The beam intensity and the beam profile monitors were designed for measuring the beam's properties. Both the range shifter and the ridge filter modulate the incoming beam energy. The LabVIEW®-based beam-irradiation-control program operates the system in a sequential operation manner for use with the MC-50 cyclotron. In addition, an in-housecoded irradiation-planning program generates an optimal irradiation path. A scanning experiment was successfully completed to print the logo of the Korea Heavy Ion Medical Accelerator (KHIMA) on GaF film. Moreover, the beam's position accuracy was measured as 0.62 mm in the x-direction and as 0.83 mm in the y-direction.

  10. Proposed new reactor-activated positron source for intense slow e + beam production

    NASA Astrophysics Data System (ADS)

    Skalsey, M.; Van House, J.

    1988-03-01

    A novel method is suggested for producing a new positron (e +) emitting isotope in a nuclear reactor with application to slow e + beams. The initial radiated sample is 124Xe which is transformed to 126I by two neutron absorptions and an intermediate decay. Over 25 Ci of positrons with a specific activity of 25 {Ci}/{gm} can be produced by this technique, allowing the generation of a slow e + beam of over 4 × 10 7{e +}/{cm 2} -s. As discussed in the conclusion, specific activities approaching 200 {Ci}/{gm} should be for activation cells are presented, one with Xe in the gas phase, the other with solid Xe. Both designs allow the easy separation of the 126I from other contaminants, permitting the production of a pure, high specific activity source.

  11. Active and passive compensation of APPLE II-introduced multipole errors through beam-based measurement

    NASA Astrophysics Data System (ADS)

    Chung, Ting-Yi; Huang, Szu-Jung; Fu, Huang-Wen; Chang, Ho-Ping; Chang, Cheng-Hsiang; Hwang, Ching-Shiang

    2016-08-01

    The effect of an APPLE II-type elliptically polarized undulator (EPU) on the beam dynamics were investigated using active and passive methods. To reduce the tune shift and improve the injection efficiency, dynamic multipole errors were compensated using L-shaped iron shims, which resulted in stable top-up operation for a minimum gap. The skew quadrupole error was compensated using a multipole corrector, which was located downstream of the EPU for minimizing betatron coupling, and it ensured the enhancement of the synchrotron radiation brightness. The investigation methods, a numerical simulation algorithm, a multipole error correction method, and the beam-based measurement results are discussed.

  12. Development of CNS Active Target for Deuteron Induced Reactions with High Intensity Exotic Beam

    NASA Astrophysics Data System (ADS)

    Ota, Shinsuke; Tokieda, H.; Lee, C. S.; Kojima, R.; Watanabe, Y. N.; Corsi, A.; Dozono, M.; Gibelin, J.; Hashimoto, T.; Kawabata, T.; Kawase, S.; Kubono, S.; Kubota, Y.; Maeda, Y.; Matsubara, H.; Matsuda, Y.; Michimasa, S.; Nakao, T.; Nishi, T.; Obertelli, A.; Otsu, H.; Santamaria, C.; Sasano, M.; Takaki, M.; Tanaka, Y.; Leung, T.; Uesaka, T.; Yako, K.; Yamaguchi, H.; Zenihiro, J.; Takada, E.

    An active target system called CAT, has been developed aiming at the measurement of deuteron induced reactions with high intensity beams in inverse kinematics. The CAT consists of a time projection chamber using THGEM and an array of Si detectors or NaI scintilators. The effective gain for the recoil particle is deisgned to be 5 - 10 × 103, while one for the beam is reduced by 102 using mesh grid to match the amplified signal to the dynamic range same as the one for recoil particle. The structure of CAT and the effect of the mesh grid are reported.

  13. Observations of the plasma environment during an active ionospheric ion beam injection experiment

    NASA Technical Reports Server (NTRS)

    Arnoldy, R. L.; Pollock, C. J.; Cahill, L. J., Jr.; Erlandson, R. E.; Kintner, P. M.

    1990-01-01

    Several sounding rocket flights have been used to clarify the electrodynamics of neutral beam releases of Ar ions in the upper ionosphere, by varying the Ar's point of release with respect to the diagnostic payload. A volume of 10-m radius centered on the Ar release payload is measured for broadband wave activity; the superthermal neutralizing beam electrons become magnetized in this volume for across-field plasma releases, and ambient electrons are accelerated to energies of several hundred eV. This is speculated to be due to wave turbulence rather than payload-neutralization.

  14. Activities on heavy ion inertial fusion and beam-driven high energy density science in Japan

    NASA Astrophysics Data System (ADS)

    Horioka, K.; Kawamura, T.; Nakajima, M.; Kondo, K.; Ogawa, M.; Oguri, Y.; Hasegawa, J.; Kawata, S.; Kikuchi, T.; Sasaki, T.; Murakami, M.; Takayama, K.

    2009-07-01

    Recent research activities in Japan relevant to heavy ion fusion (HIF) are presented. During the past two years, significant progress in HIF and high energy density (HED) physics research has been made by a number of research groups in universities and accelerator facilities. Evolutions in phase space during the longitudinal compression of intense beams were investigated at UU-NUT-TIT. Beam-plasma interaction experiments and related theoretical studies are in progress at RLNR-TIT. In the study, shock-heated hydrogen was used for the interaction experiments as a well-defined non-ideal-plasma target. In the beam-plasma interaction experiments, a special emphasis is placed on an evaluation of non-linear effects on the stopping power in a beam-heated plasma target. A direct-indirect hybrid scheme of a beam-driven ICF target has been proposed and discussed at UU. In the same group, a method for controlling the Rayleigh-Taylor instability in imploding fuel target has been proposed using oscillating heavy ion beams (HIBs). Core dynamics of the impact ignition has been investigated both experimentally and numerically at ILE—Osaka. Dense plasmas driven by intense ion beams and/or a pulse powered device, were evaluated by a group of DES-TIT, concerning the researches on HED and warm dense matter (WDM) physics. A quasi-statically tamped target was proposed to make a well-defined, warm dense state for equation-of-state (EOS) studies based on ion accelerators. The potentiality of the new facility planned at KEK was evaluated by a collaborating group of TIT-UU-KEK, which can extend the parameter regime for laboratory experiments to study the properties of matter under extreme conditions. A possible method to make a high-pressure condition for study of the planetary science was discussed as a short-term subject of intense HIBs.

  15. Fragmentation of positively-charged biological ions activated with a beam of high-energy cations.

    PubMed

    Chingin, Konstantin; Makarov, Alexander; Denisov, Eduard; Rebrov, Oleksii; Zubarev, Roman A

    2014-01-01

    First results are reported on the fragmentation of multiply protonated polypeptide ions produced in electrospray ionization mass spectrometry (ESI-MS) with a beam of high-energy cations as a source of activation. The ion beam is generated with a microwave plasma gun installed on a benchtop Q Exactive mass spectrometer. Precursor polypeptide ions are activated when trapped inside the collision cell of the instrument (HCD cell), and product species are detected in the Orbitrap analyzer. Upon exposure to the beam of air plasma cations (∼100 μA, 5 s), model precursor species such as multiply protonated angiotensin I and ubiquitin dissociated across a variety of pathways. Those pathways include the cleavages of C-CO, C-N as well as N-Cα backbone bonds, accordingly manifested as b/y, a, and c/z fragment ion series in tandem mass spectra. The fragmentation pattern observed includes characteristic fragments of collision-induced dissociation (CID) (b/y/a fragments) as well as electron capture/transfer dissociation (ECD, ETD) (c/z fragments), suggesting substantial contribution of both vibrational and electronic excitation in our experiments. Besides backbone cleavages, notable amounts of nondissociated precursor species were observed with reduced net charge, formed via electron or proton transfer between the colliding partners. Peaks corresponding to increased charge states of the precursor ions were also detected, which is the major distinctive feature of ion beam activation.

  16. Active control of the forced and transient response of a finite beam. M.S. Thesis

    NASA Technical Reports Server (NTRS)

    Post, John T.

    1990-01-01

    Structural vibrations from a point force are modelled on a finite beam. This research explores the theoretical limit on controlling beam vibrations utilizing another point source as an active controller. Three different types of excitation are considered, harmonic, random, and transient. For harmonic excitation, control over the entire beam length is possible only when the excitation frequency is near a resonant frequency of the beam. Control over a subregion may be obtained even between resonant frequencies at the cost of increasing the vibration outside of the control region. For random excitation, integrating the expected value of the displacement squared over the required interval, is shown to yield the identical cost function as obtained by integrating the cost function for harmonic excitation over all excitation frequencies. As a result, it is always possible to reduce the cost function for random excitation whether controlling the entire beam or just a subregion, without ever increasing the vibration outside the region in which control is desired. The last type of excitation considered is a single, transient pulse. The form of the controller is specified as either one or two delayed pulses, thus constraining the controller to be casual. The best possible control is examined while varying the region of control and the controller location. It is found that control is always possible using either one or two control pulses.

  17. Retrofitting tractors with rollover protective structures: perspective of equipment dealers.

    PubMed

    Tonelli, S M; Donham, K J; Leedom-Larson, K; Sanderson, W; Purschwitz, M

    2009-10-01

    This study was one of a cluster of studies that originated via requests for proposals from the NIOSH National Agricultural Tractor Safety Initiative. The present study design consisted of several steps: (1) formation of an advisory group, (2) development and testing of a standard paper self-responding survey instrument, (3) sample selection of farm equipment dealers, (4) administration of the survey, (5) assessment and analysis of the survey, and (6) in-person response panel of dealers (n = 80) to review results of the questionnaire for further definition and sharpening of the recommendations from the survey. A key finding is that most dealers do not currently sell or install ROPS retrofit kits. Barriers cited by dealers included (1) actual or perceived lack of farmer demand, (2) injury liability, (3) expensive freight for ordering ROPS, (4) lack of dealer awareness of the magnitude of deaths from tractor overturns and the high life-protective factor of ROPS, and (5) difficulty and incursion of non-recoverable expenses in locating and obtaining specific ROPS. Despite not currently selling or installing ROPS, dealers responded favorably about their future potential role in ROPS promotion and sales. Dealers were willing to further promote, sell, and install ROPS if there was demand from farmers. Recommendations include establishing a ROPS "clearing house" that dealers could contact to facilitate locating and obtaining ROPS orders from customers. Additional recommendations include education and social marketing targeting farm machinery dealers as well farmers, manufacturers, and policy makers. PMID:19967910

  18. Optical Forces in Complex Beams of Light

    NASA Astrophysics Data System (ADS)

    Ruffner, David B.

    Light possesses no mass but can transfer momentum to matter and thus can exert forces. This thesis explores these optical forces, focusing on two surprising discoveries: optical forces arising from the spin angular momentum of light and beams of light that can pull, as well as push. In the first case, we have shown that non-uniform beams of light can exert a force proportional to the curl of the spin angular momentum density. To show this we have developed a framework for understanding optical momentum in terms of experimental parameters. This framework makes clear that the curl of the spin angular momentum density contributes to the optical linear momentum. Surprisingly, we find that this contribution does not lead to spin-dependent optical forces at the electric dipole level. Experimentally, however, we find that spin-dependent optical forces do indeed act on isotropic microspheres in focused circularly-polarized beams of light. Theoretically, we confirm that spin-dependent forces appear at higher order in multipole scattering, which qualitatively explains the experimental results. Using the same theoretical framework, we show that beams of light can act as tractor beams that pull illuminated objects upstream against the direction of propagation. We demonstrate this extraordinary effect experimentally with optical conveyor beams. These experiments demonstrate long-range bidirectional transport of colloidal microparticles along propagation invariant beams of light. They show moreover that optical conveyors can move multiple particles simultaneously due to the self-healing properties of these modes of light. Not only do optical conveyors constitute practical realizations of tractor beams, but they also act as stronger traps than conventional optical traps and are less sensitive to particle composition. Axial interference endows optical conveyors with these superb trapping properties, which in turn gives them greater range than conventional optical traps. Our work

  19. Active Control of the Forced and Transient Response of a Finite Beam. M.S. Thesis

    NASA Technical Reports Server (NTRS)

    Post, John Theodore

    1989-01-01

    When studying structural vibrations resulting from a concentrated source, many structures may be modelled as a finite beam excited by a point source. The theoretical limit on cancelling the resulting beam vibrations by utilizing another point source as an active controller is explored. Three different types of excitation are considered, harmonic, random, and transient. In each case, a cost function is defined and minimized for numerous parameter variations. For the case of harmonic excitation, the cost function is obtained by integrating the mean squared displacement over a region of the beam in which control is desired. A controller is then found to minimize this cost function in the control interval. The control interval and controller location are continuously varied for several frequencies of excitation. The results show that control over the entire beam length is possible only when the excitation frequency is near a resonant frequency of the beam, but control over a subregion may be obtained even between resonant frequencies at the cost of increasing the vibration outside of the control region. For random excitation, the cost function is realized by integrating the expected value of the displacement squared over the interval of the beam in which control is desired. This is shown to yield the identical cost function as obtained by integrating the cost function for harmonic excitation over all excitation frequencies. As a result, it is always possible to reduce the cost function for random excitation whether controlling the entire beam or just a subregion, without ever increasing the vibration outside the region in which control is desired. The last type of excitation considered is a single, transient pulse. A cost function representative of the beam vibration is obtained by integrating the transient displacement squared over a region of the beam and over all time. The form of the controller is chosen a priori as either one or two delayed pulses. Delays

  20. Coherent beam combining of pulsed fibre amplifiers with active phase control

    SciTech Connect

    Wang, X L; Zhou, Pu; Ma, Y X; Ma, H T; Xu, X J; Liu, Z J; Zhao, Y J

    2011-12-31

    Coherent beam combining of pulsed fibre lasers is a promising method for power scaling while simultaneously maintaining good beam quality. We propose and demonstrate a scalable architecture for coherent beam combining of all-fibre pulsed amplifiers with active phase control using the stochastic parallel gradient descent (SPGD) algorithm. A low-pass filter is introduced to eliminate the fluctuation of the metric function caused by pulsed lasers and to extract the exact phase noise signal. Active control is thereby based on the SPGD algorithm, resulting in stable coherent beam combining at the receiving plane even in a turbulent environment. Experimental results show that the fringe visibility of the long exposure pattern increases from 0 to 0.4, and the power encircled in the main-lobe increases by 1.6 times when the system evolves from the open-loop phase-locking scheme to the closed-loop scheme. This architecture can be easily scaled up to a higher power by increasing the number of amplifying channels and the power of a single amplifier.

  1. Action Learning: a new method to increase tractor rollover protective structure (ROPS) adoption.

    PubMed

    Biddle, Elyce Anne; Keane, Paul R

    2012-01-01

    Action Learning is a problem-solving process that is used in various industries to address difficult problems. This project applied Action Learning to a leading problem in agricultural safety. Tractor overturns are the leading cause of fatal injury to farmworkers. This cause of injury is preventable using rollover protective structures (ROPS), protective equipment that functions as a roll bar structure to protect the operator in the event of an overturn. For agricultural tractors manufactured after 1976 and employee operated, Occupational Safety and Health Administration (OSHA) regulation requires employers to equip them with ROPS and seat belts. By the mid-1980s, US tractor manufacturers began adding ROPS on all farm tractors over 20 horsepower sold in the United States (http://www.nasdonline.org/document/113/d001656/rollover-protection-for-farm-tractor-operators.html). However, many older tractors remain in use without ROPS, putting tractor operators at continued risk for traumatic injury and fatality. For many older tractor models ROPS are available for retrofit, but for a variety of reasons, tractor owners have not chosen to retrofit those ROPS. The National Institute for Occupational Safety and Health (NIOSH) attempted various means to ameliorate this occupational safety risk, including the manufacture of a low-cost ROPS for self-assembly. Other approaches address barriers to adoption. An Action Learning approach to increasing adoption of ROPS was followed in Virginia and New York, with mixed results. Virginia took action to increase the manufacturing and adoption of ROPS, but New York saw problems that would be insurmountable. Increased focus on team composition might be needed to establish effective Action Learning teams to address this problem. PMID:22994641

  2. Action Learning: A New Method to Increase Tractor Rollover Protective Structure (ROPS) Adoption

    PubMed Central

    Biddle, Elyce Anne; Keane, Paul R.

    2016-01-01

    Action Learning is a problem-solving process that is used in various industries to address difficult problems. This project applied Action Learning to a leading problem in agricultural safety. Tractor overturns are the leading cause of fatal injury to farmworkers. This cause of injury is preventable using rollover protective structures (ROPS), protective equipment that functions as a roll bar structure to protect the operator in the event of an overturn. For agricultural tractors manufactured after 1976 and employee operated, Occupational Safety and Health Administration (OSHA) regulation requires employers to equip them with ROPS and seat belts. By the mid-1980s, US tractor manufacturers began adding ROPS on all farm tractors over 20 horsepower sold in the United States (http://www.nasdonline.org/document/113/d001656/rollover-protection-for-farm-tractor-operators.html). However, many older tractors remain in use without ROPS, putting tractor operators at continued risk for traumatic injury and fatality. For many older tractor models ROPS are available for retrofit, but for a variety of reasons, tractor owners have not chosen to retrofit those ROPS. The National Institute for Occupational Safety and Health (NIOSH) attempted various means to ameliorate this occupational safety risk, including the manufacture of a low-cost ROPS for self-assembly. Other approaches address barriers to adoption. An Action Learning approach to increasing adoption of ROPS was followed in Virginia and New York, with mixed results. Virginia took action to increase the manufacturing and adoption of ROPS, but New York saw problems that would be insurmountable. Increased focus on team composition might be needed to establish effective Action Learning teams to address this problem. PMID:22994641

  3. Actively mode-locked all fiber laser with cylindrical vector beam output.

    PubMed

    Zhou, Yong; Wang, Anting; Gu, Chun; Sun, Biao; Xu, Lixin; Li, Feng; Chung, Dick; Zhan, Qiwen

    2016-02-01

    We demonstrated an all fiber actively mode-locked laser that emits a cylindrical vector beam. An intra-cavity few-mode fiber Bragg grating inscribed in a short section of four-mode fiber is employed to provide mode selection and spectrum filtering functions. Mode coupling is achieved by offset splicing between the single-mode fiber and the four-mode fiber in the laser cavity. A LiNbO3 Mach-Zehnder modulator is used to achieve active mode-locking in the laser. The laser operates at 1547 nm with 30 dB spectrum width of 0.2 nm. The mode-locked pulses have a duration of 2 ns and repetition of 12.06 MHz. Through adjusting the polarization state in the laser cavity, both radially and azimuthally polarized beams have been obtained with high mode purity.

  4. Actively mode-locked all fiber laser with cylindrical vector beam output.

    PubMed

    Zhou, Yong; Wang, Anting; Gu, Chun; Sun, Biao; Xu, Lixin; Li, Feng; Chung, Dick; Zhan, Qiwen

    2016-02-01

    We demonstrated an all fiber actively mode-locked laser that emits a cylindrical vector beam. An intra-cavity few-mode fiber Bragg grating inscribed in a short section of four-mode fiber is employed to provide mode selection and spectrum filtering functions. Mode coupling is achieved by offset splicing between the single-mode fiber and the four-mode fiber in the laser cavity. A LiNbO3 Mach-Zehnder modulator is used to achieve active mode-locking in the laser. The laser operates at 1547 nm with 30 dB spectrum width of 0.2 nm. The mode-locked pulses have a duration of 2 ns and repetition of 12.06 MHz. Through adjusting the polarization state in the laser cavity, both radially and azimuthally polarized beams have been obtained with high mode purity. PMID:26907420

  5. All fiber actively mode-locked fiber laser emitting cylindrical vector beam

    NASA Astrophysics Data System (ADS)

    Zhou, Yong; Wang, Anting; Gu, Chun; Xu, Lixin; Zhan, Qiwen

    2015-08-01

    We demonstrated an all fiber actively mode-locked laser emitting cylindrical vector beam. A few-mode fiber Bragg grating is adopted to achieve mode selecting and spectrum filtering. An offset splicing of single-mode fiber with fourmode fiber is utilized as a mode coupler in the laser cavity. A LiNbO3 Mach-Zehnder modulator is used to achieve active mode locking in the laser. The laser operates at 1547nm with 30 dB spectrum width of 0.3nm. The emitted modelocked pulses have a duration of 1ns and repetition of 12.06MHz. Both radially and azimuthally polarized beams have been obtained with very good modal symmetry by adjusting the polarization in the laser cavity.

  6. A new single crystal diamond dosimeter for small beam: comparison with different commercial active detectors.

    PubMed

    Marsolat, F; Tromson, D; Tranchant, N; Pomorski, M; Le Roy, M; Donois, M; Moignau, F; Ostrowsky, A; De Carlan, L; Bassinet, C; Huet, C; Derreumaux, S; Chea, M; Cristina, K; Boisserie, G; Bergonzo, P

    2013-11-01

    Recent developments of new therapy techniques using small photon beams, such as stereotactic radiotherapy, require suitable detectors to determine the delivered dose with a high accuracy. The dosimeter has to be as close as possible to tissue equivalence and to exhibit a small detection volume compared to the size of the irradiation field, because of the lack of lateral electronic equilibrium in small beam. Characteristics of single crystal diamond (tissue equivalent material Z = 6, high density) make it an ideal candidate to fulfil most of small beam dosimetry requirements. A commercially available Element Six electronic grade synthetic diamond was used to develop a single crystal diamond dosimeter (SCDDo) with a small detection volume (0.165 mm(3)). Long term stability was studied by irradiating the SCDDo in a (60)Co beam over 14 h. A good stability (deviation less than ± 0.1%) was observed. Repeatability, dose linearity, dose rate dependence and energy dependence were studied in a 10 × 10 cm(2) beam produced by a Varian Clinac 2100 C linear accelerator. SCDDo lateral dose profile, depth dose curve and output factor (OF) measurements were performed for small photon beams with a micro multileaf collimator m3 (BrainLab) attached to the linac. This study is focused on the comparison of SCDDo measurements to those obtained with different commercially available active detectors: an unshielded silicon diode (PTW 60017), a shielded silicon diode (Sun Nuclear EDGE), a PinPoint ionization chamber (PTW 31014) and two natural diamond detectors (PTW 60003). SCDDo presents an excellent spatial resolution for dose profile measurements, due to its small detection volume. Low energy dependence (variation of 1.2% between 6 and 18 MV photon beam) and low dose rate dependence of the SCDDo (variation of 1% between 0.53 and 2.64 Gy min(-1)) are obtained, explaining the good agreement between the SCDDo and the efficient unshielded diode (PTW 60017) in depth dose curve

  7. Modeling activities on the negative-ion-based Neutral Beam Injectors of the Large Helical Device

    SciTech Connect

    Agostinetti, P.; Antoni, V.; Chitarin, G.; Pilan, N.; Serianni, G.; Veltri, P.; Cavenago, M.; Nakano, H.; Takeiri, Y.; Tsumori, K.

    2011-09-26

    At the National Institute for Fusion Science (NIFS) large-scaled negative ion sources have been widely used for the Neutral Beam Injectors (NBIs) mounted on the Large Helical Device (LHD), which is the world-largest superconducting helical system. These injectors have achieved outstanding performances in terms of beam energy, negative-ion current and optics, and represent a reference for the development of heating and current drive NBIs for ITER.In the framework of the support activities for the ITER NBIs, the PRIMA test facility, which includes a RF-drive ion source with 100 keV accelerator (SPIDER) and a complete 1 MeV Neutral Beam system (MITICA) is under construction at Consorzio RFX in Padova.An experimental validation of the codes has been undertaken in order to prove the accuracy of the simulations and the soundness of the SPIDER and MITICA design. To this purpose, the whole set of codes have been applied to the LHD NBIs in a joint activity between Consorzio RFX and NIFS, with the goal of comparing and benchmarking the codes with the experimental data. A description of these modeling activities and a discussion of the main results obtained are reported in this paper.

  8. Performance of a lead-scintillation-fiber calorimeter designed as an active beam shield for the VENUS detector

    NASA Astrophysics Data System (ADS)

    Takasaki, Fumihiko; Utsumi, M.; Fukui, T.; Narita, Y.; Hosoda, N.; Hirose, T.; Chiba, M.

    1992-11-01

    We made a cylindrical calorimeter which consisted of plastic scintillating fibers and lead. This calorimeter was designed to serve as an active beam shield for the VENUS detector [1] at the TRISTAN electron-positron collider [2]. This device has been successfully used as a beam background shield and as a luminosity monitor of the VENUS detector.

  9. Effect of Road Adhesion Coefficient on Tractor-Semitrailer Cornering Braking Stability

    NASA Astrophysics Data System (ADS)

    Wang, Wei; Li, Chen; Tang, Geteng; Wang, Cheng

    A dynamic model of tractor-semitrailer cornering braking was established in this paper, and the accuracy of the model was verified by real vehicle test. By model simulation of the cornering braking process, different road adhesion coefficient such as 0.15, 0.3, 0.45, 0.6, 0.75 was chosen to analyzed the changing curve of braking distance, articulation angle, yaw rate and lateral acceleration when initial speed of tractor-semitrailer was 30km h. The result showed that the peak values of articulation angle, yaw rate and lateral acceleration gotten by simulation were the largest. On the road of road adhesion coefficient 0.15, distance of tractor-semitrailer cornering braking was the longest. On the road of road adhesion coefficient 0.75, distance of tractor-semitrailer cornering braking was the shortest and the peak values of articulation angle, yaw rate and lateral acceleration were small relatively.

  10. Design and Implementation of a GPS Guidance System for Agricultural Tractors Using Augmented Reality Technology

    PubMed Central

    Santana-Fernández, Javier; Gómez-Gil, Jaime; del-Pozo-San-Cirilo, Laura

    2010-01-01

    Current commercial tractor guidance systems present to the driver information to perform agricultural tasks in the best way. This information generally includes a treated zones map referenced to the tractor’s position. Unlike actual guidance systems where the tractor driver must mentally associate treated zone maps and the plot layout, this paper presents a guidance system that using Augmented Reality (AR) technology, allows the tractor driver to see the real plot though eye monitor glasses with the treated zones in a different color. The paper includes a description of the system hardware and software, a real test done with image captures seen by the tractor driver, and a discussion predicting that the historical evolution of guidance systems could involve the use of AR technology in the agricultural guidance and monitoring systems. PMID:22163479

  11. Summary of NREL's Recent Class 8 Tractor Trailer Platooning Testing (Presentation)

    SciTech Connect

    Lammert, M.; Kelly, K.; Walkowicz, K.

    2014-08-01

    This presentation summarizes NREL's recent class 8 tractor trailer platooning testing, including analysis of SAE J1321 Type II fuel consumption testing, fuel consumption improvement, fuel economy and platooning position accuracy.

  12. The smooth (tractor) operator: insights of knowledge engineering.

    PubMed

    Cullen, Ralph H; Smarr, Cory-Ann; Serrano-Baquero, Daniel; McBride, Sara E; Beer, Jenay M; Rogers, Wendy A

    2012-11-01

    The design of and training for complex systems requires in-depth understanding of task demands imposed on users. In this project, we used the knowledge engineering approach (Bowles et al., 2004) to assess the task of mowing in a citrus grove. Knowledge engineering is divided into four phases: (1) Establish goals. We defined specific goals based on the stakeholders involved. The main goal was to identify operator demands to support improvement of the system. (2) Create a working model of the system. We reviewed product literature, analyzed the system, and conducted expert interviews. (3) Extract knowledge. We interviewed tractor operators to understand their knowledge base. (4) Structure knowledge. We analyzed and organized operator knowledge to inform project goals. We categorized the information and developed diagrams to display the knowledge effectively. This project illustrates the benefits of knowledge engineering as a qualitative research method to inform technology design and training.

  13. The Tractor: Probabilistic astronomical source detection and measurement

    NASA Astrophysics Data System (ADS)

    Lang, Dustin; Hogg, David W.; Mykytyn, David

    2016-04-01

    The Tractor optimizes or samples from models of astronomical objects. The approach is generative: given astronomical sources and a description of the image properties, the code produces pixel-space estimates or predictions of what will be observed in the images. This estimate can be used to produce a likelihood for the observed data given the model: assuming the model space actually includes the truth (it doesn’t, in detail), then if we had the optimal model parameters, the predicted image would differ from the actually observed image only by noise. Given a noise model of the instrument and assuming pixelwise independent noise, the log-likelihood is the negative chi-squared difference: (image - model) / noise.

  14. Using LNG as a Fuel in Heavy-Duty Tractors

    SciTech Connect

    Liquid Carbonic, Inc. and Trucking Research Institute

    1999-08-09

    Recognizing the lack of operational data on alternative fuel heavy-truck trucks, NREL contracted with the Trucking Research Institute (TRI) in 1994 to obtain a cooperative agreement with Liquid Carbonic. The purpose of this agreement was to (1) purchase and operate liquid natural gas- (LNG-) powered heavy-duty tractor-trailers with prototype Detroit Diesel Corporation (DDC) Series 60 natural gas (S60G) engines in over-the-road commercial service applications; and (2) collect and provide operational data to DDC to facilitate the on-road prototype development of the engine and to NREL for the Alternative Fuels Data Center. The vehicles operated from August 1994 through April of 1997 and led to a commercially available, emissions-certified S60G in 1998. This report briefly documents the engine development, the operational characteristics of LNG, and the lessons learned during the project.

  15. Soil compaction and structural morphology under tractor wheelings

    NASA Astrophysics Data System (ADS)

    Shanahan, Peter; Quinton, John; Binley, Andrew; Silgram, Martyn

    2010-05-01

    Compaction of cultivated soils is a major problem for agriculture in terms of yield decline and sustainable soil resource management. Tramline wheelings exacerbate runoff and increase erosion from arable land. The UK Department for Environment, Food and Rural Affairs (Defra) LINK Project - a joint venture between agri-business, land managers and research groups - is currently evaluating a number of methods for alleviating compaction in tractor wheelings across a range of soil types in England. Using innovative applications of agri-geophysics (e.g. ground penetrating radar, electrical resistivity, acoustics and x-ray tomography), this current project aims to determine relationships between properties derived from geophysical methods (e.g. soil moisture, porosity), soil compaction and structural morphology. Such relationships are important for a clearer understanding of hydrological and biogeochemical processes in compacted soils, to address land management practices and develop cost-effective mitigation measures. Our poster will present some early results of this study.

  16. An investigation of drag reduction for tractor trailer vehicles

    NASA Technical Reports Server (NTRS)

    Muirhead, V. U.

    1978-01-01

    Force and moment data were obtained from a one-twenty-fifth scale wind tunnel model of a cab-over-engine tractor trailer combination. The tests define the aerodynamic characteristics of the baseline (unmodified) vehicle and several modified configurations. The primary modifications consist of: (1) greatly increased forebody corner radii, (2) a smooth fairing over the cab-to-trailer gap, (3) a smoothed underbody, and (4) rear streamlining (boattailing)of the trailer. Tests were conducted for yaw angles from 0 deg to 30 deg. The reduction in drag, relative to the baseline, obtained by combining the modifications are compared for the zero yaw condition with full scale coast down drag results for similar configurations. The drag reductions obtained from the model and full scale tests are in good agreement.

  17. Prevalence of drug use in commercial tractor-trailer drivers.

    PubMed

    Couper, Fiona J; Pemberton, Melissa; Jarvis, Anjanette; Hughes, Marty; Logan, Barry K

    2002-05-01

    An enforcement emphasis project, "Operation Trucker Check," was established in order to determine the extent to which commercial tractor-trailer drivers were operating their vehicles while impaired by drugs. A total of 1079 drivers and their vehicles were assessed for driver and equipment violations, and drivers additionally underwent preliminary field sobriety tests conducted by drug recognition expert (DRE) officers. Anonymous urine specimens for drug analysis were requested, and 822 urine specimens were obtained in total. Compliance with the drug-testing portion was voluntary, and there was a 19% refusal rate. Overall, 21% of the urine specimens tested positive for either illicit, prescription, and/or over-the-counter drugs, and 7% tested positive for more than one drug. Excluding caffeine and nicotine, the largest number of positive findings (9.5%) were for CNS stimulants, such as methamphetamine, amphetamine, phentermine, ephedrine/pseudoephedrine, and cocaine. The second most frequently encountered drug class were the cannabinoids, with 4.3% of drivers testing positive for marijuana metabolites. Only 11 drivers (1.3%) were positive for alcohol. Sixteen truck drivers (1.6%) were charged with driving under the influence of drugs after a full DRE evaluation was conducted. The results indicate that in spite of comprehensive drug testing in the trucking industry, some tractor-trailer drivers are continuing to take illicit and other drugs with the potential of having a negative effect on their driving ability. On the other hand, only a few drivers were, in fact, deemed to be under the influence of drugs at the time of driving when evaluated by DRE officers.

  18. Prevalence of drug use in commercial tractor-trailer drivers.

    PubMed

    Couper, Fiona J; Pemberton, Melissa; Jarvis, Anjanette; Hughes, Marty; Logan, Barry K

    2002-05-01

    An enforcement emphasis project, "Operation Trucker Check," was established in order to determine the extent to which commercial tractor-trailer drivers were operating their vehicles while impaired by drugs. A total of 1079 drivers and their vehicles were assessed for driver and equipment violations, and drivers additionally underwent preliminary field sobriety tests conducted by drug recognition expert (DRE) officers. Anonymous urine specimens for drug analysis were requested, and 822 urine specimens were obtained in total. Compliance with the drug-testing portion was voluntary, and there was a 19% refusal rate. Overall, 21% of the urine specimens tested positive for either illicit, prescription, and/or over-the-counter drugs, and 7% tested positive for more than one drug. Excluding caffeine and nicotine, the largest number of positive findings (9.5%) were for CNS stimulants, such as methamphetamine, amphetamine, phentermine, ephedrine/pseudoephedrine, and cocaine. The second most frequently encountered drug class were the cannabinoids, with 4.3% of drivers testing positive for marijuana metabolites. Only 11 drivers (1.3%) were positive for alcohol. Sixteen truck drivers (1.6%) were charged with driving under the influence of drugs after a full DRE evaluation was conducted. The results indicate that in spite of comprehensive drug testing in the trucking industry, some tractor-trailer drivers are continuing to take illicit and other drugs with the potential of having a negative effect on their driving ability. On the other hand, only a few drivers were, in fact, deemed to be under the influence of drugs at the time of driving when evaluated by DRE officers. PMID:12051337

  19. Pilot experiments for the International Thermonuclear Experimental Reactor active beam spectroscopy diagnostic

    NASA Astrophysics Data System (ADS)

    Hellermann, M. von; Bock, M. de; Jaspers, R.; Jakubowska, K.; Barnsley, R.; Giroud, C.; Hawkes, N. C.; Zastrow, K. D.; Lotte, P.; Giannella, R.; Malaquias, A.; Rachlew, E.; Tugarinov, S.; Krasilnikov, A.; Litnovsky, A.; Philipps, V.; Wienhold, P.; Oelhafen, P.; Temmerman, G. De; Shmaenok, L.

    2004-10-01

    Supporting pilot experiments and activities which are currently considered or already performed for the development of the International Thermonuclear Experiment Reactor active beam spectroscopy diagnostic are addressed in this article. Four key issues are presented including optimization of spectral instrumentation, feasibility of a motional Stark effect (MSE) evaluation based on line ratios, "first-mirror" test-bed experiments at the tokamak TEXTOR, and finally the role of integrated data analysis for the conceptual layout of the change exchange recombination spectroscopy and MSE diagnostic.

  20. Exposure to audible and infrasonic noise by modern agricultural tractors operators.

    PubMed

    Bilski, Bartosz

    2013-03-01

    The wheeled agricultural tractor is one of the most prominent sources of noise in agriculture. This paper presents the assessment of the operator's exposure to audible and infrasonic noise in 32 selected modern wheeled agricultural tractors designed and produced by world-renowned companies in normal working conditions. The tractors have been in use for no longer than 4 years, with rated power of 51 kW to up to 228 kW (as per 97/68 EC). Audible and infrasonic noise level measurements and occupational exposure analysis to noise were performed according to ISO 9612:2009 (strategy 1 - task-based measurements). The measurements were made in different typical work conditions inside and outside of tractors cabs. The results indicated that exposure levels to noise perceived by the operators (L(ex,Te) between 62,3 and 84,7 dB-A) and can make a small risk of potential adversely effects on hearing during tasks performed inside the closed cab. It should be remarked that uncertainty interval is wider and in in some conditions can occur transgression of audible noise occupational exposure limits. The measured audible noise levels can potentially develop the non-auditory effects. Analysed tractors emit considerable infrasonic noise levels that tend to exceed the occupational exposure limits (both inside and outside the driver's cab). The levels of infrasound: 83,8-111,4 dB-G. All tractors introduced for sale should be subjected to tests in terms of infrasonic noise levels. The applicable standards for low frequency noise and its measurement methods for vehicles, including agricultural tractors, should be scientifically revised. In the last years there has been a noticeable technical progress in reduction of audible noise exposure at the tractors operators workplaces with simultaneously lack of important works for limitation of exposure to infrasound. Author discuss possible health and ergonomic consequencies of such exposure. PMID:22877701

  1. Investigation of Tractor Base Bleeding for Heavy Vehicle Aerodynamic Drag Reduction

    SciTech Connect

    Ortega, J; Salari, K; Storms, B

    2007-10-25

    One of the main contributors to the aerodynamic drag of a heavy vehicle is tractor-trailer gap drag, which arises when the vehicle operates within a crosswind. Under this operating condition, freestream flow is entrained into the tractor-trailer gap, imparting a momentum exchange to the vehicle and subsequently increasing the aerodynamic drag. While a number of add-on devices, including side extenders, splitter plates, vortex stabilizers, and gap sealers, have been previously tested to alleviate this source of drag, side extenders remain the primary add-on device of choice for reducing tractor-trailer gap drag. However, side extenders are not without maintenance and operational issues. When a heavy vehicle pivots sharply with respect to the trailer, as can occur during loading or unloading operations, the side extenders can become crushed against the trailer. Consequently, fleet operators are forced to incur additional costs to cover the repair or replacement of the damaged side extenders. This issue can be overcome by either shortening the side extenders or by devising an alternative drag reduction concept that can perform just as effectively as side extenders. To explore such a concept, we investigate tractor base bleeding as a means of reducing gap drag. Wind tunnel measurements are made on a 1:20 scale heavy vehicle model at a vehicle width-based Reynolds number of 420,000. The tractor bleeding flow, which is delivered through a porous material embedded within the tractor base, is introduced into the tractor-trailer gap at bleeding coefficients ranging from 0.0-0.018. To determine the performance of tractor base bleeding under more realistic operating conditions, computational fluid dynamics simulations are performed on a full-scale heavy vehicle within a crosswind for bleeding coefficients ranging from 0.0-0.13.

  2. Exposure to audible and infrasonic noise by modern agricultural tractors operators.

    PubMed

    Bilski, Bartosz

    2013-03-01

    The wheeled agricultural tractor is one of the most prominent sources of noise in agriculture. This paper presents the assessment of the operator's exposure to audible and infrasonic noise in 32 selected modern wheeled agricultural tractors designed and produced by world-renowned companies in normal working conditions. The tractors have been in use for no longer than 4 years, with rated power of 51 kW to up to 228 kW (as per 97/68 EC). Audible and infrasonic noise level measurements and occupational exposure analysis to noise were performed according to ISO 9612:2009 (strategy 1 - task-based measurements). The measurements were made in different typical work conditions inside and outside of tractors cabs. The results indicated that exposure levels to noise perceived by the operators (L(ex,Te) between 62,3 and 84,7 dB-A) and can make a small risk of potential adversely effects on hearing during tasks performed inside the closed cab. It should be remarked that uncertainty interval is wider and in in some conditions can occur transgression of audible noise occupational exposure limits. The measured audible noise levels can potentially develop the non-auditory effects. Analysed tractors emit considerable infrasonic noise levels that tend to exceed the occupational exposure limits (both inside and outside the driver's cab). The levels of infrasound: 83,8-111,4 dB-G. All tractors introduced for sale should be subjected to tests in terms of infrasonic noise levels. The applicable standards for low frequency noise and its measurement methods for vehicles, including agricultural tractors, should be scientifically revised. In the last years there has been a noticeable technical progress in reduction of audible noise exposure at the tractors operators workplaces with simultaneously lack of important works for limitation of exposure to infrasound. Author discuss possible health and ergonomic consequencies of such exposure.

  3. An Active Target-Time Projection Chamber (AT-TPC) for reaccelerated beams

    NASA Astrophysics Data System (ADS)

    Beceiro-Novo, Saul; Ahn, T.; Abu-Nimeh, F.; Bazin, D.; Bradt, J.; Chajecki, Z.; Fritsch, A.; Kohley, Z.; Kolata, J. J.; Lynch, W.; Mittig, W.; Suzuki, D.; Usher, N.

    2014-09-01

    Reaccelerated radioactive beams near the Coulomb barrier, which will soon be available from the ReA3 accelerator at NSCL, will open up new opportunities for the study of nuclear structure near the driplines. Since these beams can only be produced at modest intensities, efficient techniques must be used for measurement. The Active Target- Time Projection Chamber (AT-TPC), which was developed at MSU, solves this problem by providing the increased luminosity of a thick target while maintaining a good energy resolution by tracking the reaction vertex over an essentially 4 π solid angle. The AT-TPC and similar detectors allow us to take full advantage of the radioactive ion beams at present and future nuclear physics facilities to explore the frontier of rare isotopes where much of the spectroscopic information is unknown. We used a prototype of the AT-TPC to study resonances in light nuclei, and some illustrative results will be shown. The AT-TPC technology will be presented together with new experimental results and the commissioning of the detector and its 10240 electronic channels. Reaccelerated radioactive beams near the Coulomb barrier, which will soon be available from the ReA3 accelerator at NSCL, will open up new opportunities for the study of nuclear structure near the driplines. Since these beams can only be produced at modest intensities, efficient techniques must be used for measurement. The Active Target- Time Projection Chamber (AT-TPC), which was developed at MSU, solves this problem by providing the increased luminosity of a thick target while maintaining a good energy resolution by tracking the reaction vertex over an essentially 4 π solid angle. The AT-TPC and similar detectors allow us to take full advantage of the radioactive ion beams at present and future nuclear physics facilities to explore the frontier of rare isotopes where much of the spectroscopic information is unknown. We used a prototype of the AT-TPC to study resonances in light nuclei

  4. Active Nozzle Control and Integrated Design Optimization of a Beam Subject to Fluid-Dynamic Forces

    NASA Astrophysics Data System (ADS)

    Borglund, D.

    1999-02-01

    Active nozzle control is used to improve the stability of a beam subject to forces induced by fluid flow through attached pipes. The control system has a significant effect on the structural stability, making both flutter and divergence type of instabilities possible. The stability analysis is carried out using a state-variable approach based on a finite element formulation of the structural dynamics. The simultaneous design of the control system and the beam shape minimizing structural mass is performed using numerical optimization. The inclusion of the control system in the optimization gives a considerable reduction of the structural mass but results in an optimal design which is very sensitive to imperfections. Using a simple model of the control system uncertainties, a more robust design is obtained by solving a modified optimization problem. Throughout the study, the theoretical findings are verified by experiments.

  5. Semi-active damping strategy for beams system with pneumatically controlled granular structure

    NASA Astrophysics Data System (ADS)

    Bajkowski, Jacek M.; Dyniewicz, Bartłomiej; Bajer, Czesław I.

    2016-03-01

    The paper deals with a control method for semi-active damping of a double beam system with a smart granular structure placed in a thin silicone envelope. The damping properties of the system are controlled pneumatically, by subjecting the granular material to underpressure at particular moments. A mathematical model of the layered beam with a granular damping structure is represented by the two degrees of freedom, modified Kelvin-Voigt model of two masses, a spring with controllable stiffness, and a viscous damper with a variable damping coefficient. The optimal control problem is posed, using the concept of switching of the parameters to increase the efficiency of suppressing the displacement's amplitude. The resulting control strategy was verified experimentally for free vibrations of a cantilever system. The research proved that the appropriate, periodic switching of the properties of the considered structure enables reducing the vibration more effectively than if the material is treated passively.

  6. Field Tests of a Tractor Rollover Detection and Emergency Notification System.

    PubMed

    Liu, B; Koc, A B

    2015-04-01

    The objective of this research was to assess the feasibility of a rollover detection and emergency notification system for farm tractors using field tests. The emergency notification system was developed based on a tractor stability model and implemented on a mobile electronic device with the iOS operating system. A complementary filter was implemented to combine the data from the accelerometer and gyroscope sensors to improve their accuracies in calculating the roll and pitch angles and the roll and pitch rates. The system estimates a stability index value during tractor operation, displays feedback messages when the stability index is lower than a preset threshold value, and transmits emergency notification messages when an overturn happens. Ten tractor rollover tests were conducted on a field track. The developed system successfully monitored the stability of the tractor during all of the tests. The iOS application was able to detect rollover accidents and transmit emergency notifications in the form of a phone call and email when an accident was detected. The system can be a useful tool for training and education in safe tractor operation. The system also has potential for stability monitoring and emergency notification of other on-road and off-road motorized vehicles. PMID:26204787

  7. The Social Marketing of Safety Behaviors: A Quasi–Randomized Controlled Trial of Tractor Retrofitting Incentives

    PubMed Central

    Jenkins, Paul L.; Emmelin, Maria; Stenlund, Hans; Weinehall, Lars; Earle-Richardson, Giulia B.; May, John J.

    2011-01-01

    Objectives. We assessed the effect of social marketing incentives on dispositions toward retrofitting and retrofitting behavior among farmers whose tractors lacked rollover protective structures. Methods. From 2006 to 2007, we conducted a quasi–randomized controlled trial with 391 farm owners in New York and Pennsylvania surveyed before and after exposure to 1 of 3 tractor retrofitting incentive combinations. These combinations were offered in 3 trial regions; region 1 received rebates; region 2 received rebates, messages, and promotion and was considered the social marketing region; and region 3 received messages and promotion. A fourth region served as a control. Results. The social marketing region generated the greatest increases in readiness to retrofit, intentions to retrofit, and message recall. In addition, postintervention stage of change, intentions, attitudes, subjective norms, and perceived behavioral control levels were higher among farmers who had retrofitted tractors. Conclusions. Our results showed that a social marketing approach (financial incentives, tailored messages, and promotion) had the greatest influence on message recall, readiness to retrofit tractors, and intentions to retrofit tractors and that behavioral measures were fairly good predictors of tractor retrofitting behaviors. PMID:21330581

  8. Anthropometric criteria for the design of tractor cabs and protection frames.

    PubMed

    Hsiao, H; Whitestone, J; Bradtmiller, B; Whisler, R; Zwiener, J; Lafferty, C; Kau, T-Y; Gross, M

    2005-03-15

    Improved human-tractor interface designs, such as well-accommodated operator enclosures (i.e. cabs and protection frames) can enhance operator productivity, comfort and safety. This study investigated farm-worker anthropometry and determined the critical anthropometric measures and 3-D feature envelopes of body landmarks for the design of tractor operator enclosures. One hundred agriculture workers participated in the study. Their body size and shape information was registered, using a 3-D full-body laser scanner. Knee height (sitting) and another eight parameters were found to affect the cab-enclosure accommodation rating and multiple anthropometric dimensions interactively affected the steering wheel and gear-handle impediment. A principal component analysis has identified 15 representative human body models for digitally assessing tractor-cab accommodation. A set of centroid coordinates of 34 body landmarks and the 95% confidence semi-axis-length for each landmark location were developed to guide tractor designers in their placement of tractor control components in order to best accommodate the user population. Finally, the vertical clearance (90 cm) for agriculture tractor enclosure in the current SAE International J2194 standard appeared to be too short as compared to the 99th percentile sitting height of male farm workers in this study (100.6 cm) and in the 1994 National Health and Nutrition Examination Survey III database (99.9 cm) and of the male civilian population in the 2002 Civilian American and European Surface Anthropometric Resource database (100.4 cm). PMID:15804844

  9. Implementing a National Tractor Safety Program: Using "Whole System in a Room" to Mobilize Partners and Implement Solutions.

    PubMed

    Tinc, Pamela J; Ayers, Paul; May, John J; Purschwitz, Mark A; Park, Samantha; Bayes, Barbara; Sorensen, Julie

    2016-01-01

    Fatalities due to tractor overturns have long plagued the U.S. farm community. Constituting 20% of agricultural fatalities, tractor overturns contribute significantly to high rates of fatal injuries. In the past, many efforts have been directed toward reducing tractor overturns, with one successful US-based program offering rebates to farmers who retrofit their tractors with rollover protective structures (ROPS). In an effort to expand the program, the National Tractor Safety Coalition was formed. This coalition hosted a "Whole System in the Room" workshop to bring 50 stakeholders together. During this workshop, participants worked together to identify a common vision for the future of tractor safety and ROPS programs and commit to action. At the close of the workshop, coalition members set out to begin work on 100 short- and long-term commitments to begin implementing a National ROPS Rebate Program. PMID:26788905

  10. Wakefields Generated by Electron Beams Passing through a Waveguide Loaded with an Active Medium

    SciTech Connect

    Tyukhtin, Andrey; Kanareykin, Alexei; Schoessow, Paul

    2006-11-27

    The wakefields of a relativistic electron beam passing through a waveguide loaded with an active medium with weak resonant dispersion have been considered. For the calculations in this paper the parameters of the medium are those of a solution of fullerene (C60) in a nematic liquid crystal that exhibits activity in the X-band. It was shown that several of the TM accelerating modes can be amplified for the geometries under consideration; structures in which higher order modes are amplified exhibit essential advantages as PASERs. In particular, the amplification of the highest mode occurs in a structure loaded with a rather thick active medium layer that maximizes the energy stored by the active medium.

  11. Experimental studies on active vibration control of a smart composite beam using a PID controller

    NASA Astrophysics Data System (ADS)

    Jovanović, Miroslav M.; Simonović, Aleksandar M.; Zorić, Nemanja D.; Lukić, Nebojša S.; Stupar, Slobodan N.; Ilić, Slobodan S.

    2013-11-01

    This paper presents experimental verification of the active vibration control of a smart cantilever composite beam using a PID controller. In order to prevent negative occurrences in the derivative and integral terms in a PID controller, first-order low-pass filters are implemented in the derivative action and in the feedback of the integral action. The proposed application setup consists of a composite cantilever beam with a fiber-reinforced piezoelectric actuator and strain gage sensors. The beam is modeled using a finite element method based on third-order shear deformation theory. The experiment considers vibration control under periodic excitation and an initial static deflection. A control algorithm was implemented on a PIC32MX440F256H microcontroller. Experimental results corresponding to the proposed PID controller are compared with corresponding results using proportional (P) control, proportional-integral (PI) control and proportional-derivative (PD) control. Experimental results indicate that the proposed PID controller provides 8.93% more damping compared to a PD controller, 14.41% more damping compared to a PI controller and 19.04% more damping compared to a P controller in the case of vibration under periodic excitation. In the case of free vibration control, the proposed PID controller shows better performance (settling time 1.2 s) compared to the PD controller (settling time 1.5 s) and PI controller (settling time 2.5 s).

  12. Improvement of chaperone activity of 2-Cys peroxiredoxin using electron beam

    NASA Astrophysics Data System (ADS)

    Hong, Sung Hyun; An, Byung Chull; Lee, Seung Sik; Lee, Jae Taek; Cho, Jae-Hyun; Jung, Hyun Suk; Chung, Byung Yeoup

    2012-08-01

    The peroxiredoxin protein expressed in Pseudomonas aeruginosa PAO1 (PaPrx) is a typical 2-cysteine peroxiredoxin that has dual functions as both a thioredoxin-dependent peroxidase and molecular chaperone. As the function of PaPrx is regulated by its structural status, in the present study, we examined the effects of electron beam radiation on the structural modifications of PaPrx, as well as changes to PaPrx peroxidase and chaperone functions. It was found that the chaperone activity of PaPrx was increased approximately 3- to 4-fold at 2 kGy when compared to non-irradiated PaPrx, while its peroxidase activity decreased. This corresponded to a shift from the low molecular weight PaPrx species that acts as a peroxidase to the high molecular weight complex that functions as a chaperone, as detected using polyacrylamide gel electrophoresis. We also investigated the influence of the electron beam on physical protein properties such as hydrophobicity and secondary structure. The exposure of the PaPrx hydrophobic domains in response to irradiation reached a peak at 2 kGy and then decreased in a dose-dependent manner at higher doses. In addition, the exposure of β-sheet and random coil elements on the surface of PaPrx was significantly increased following irradiation with an electron beam, whereas exposure of α-helix and turn elements was decreased. These results suggest that irradiated PaPrx may be a potential candidate for use in bio-engineering systems and various industrial applications, due to its enhanced chaperone activity.

  13. Evaluation of uncertainty in experimental active buckling control of a slender beam-column with disturbance forces using Weibull analysis

    NASA Astrophysics Data System (ADS)

    Enss, Georg C.; Platz, Roland

    2016-10-01

    Buckling of slender load-bearing beam-columns is a crucial failure scenario in light-weight structures as it may result in the collapse of the entire structure. If axial load and load capacity are unknown, stability becomes uncertain. To compensate this uncertainty, the authors successfully developed and evaluated an approach for active buckling control for a slender beam-column, clamped at the base and pinned at the upper end. Active lateral forces are applied with two piezoelectric stack actuators in opposing directions near the beam-column' clamped base to prevent buckling. A Linear Quadratic Regulator is designed and implemented on the experimental demonstrator and statistical tests are conducted to prove effectivity of the active approach. The load capacity of the beam-column could be increased by 40% and scatter of buckling occurrences for increasing axial loads is reduced. Weibull analysis is used to evaluate the increase of the load capacity and its related uncertainty compensation.

  14. Crystallographic dependence of photocatalytic activity of WO3 thin films prepared by molecular beam epitaxy.

    PubMed

    Li, Guoqiang; Varga, Tamas; Yan, Pengfei; Wang, Zhiguo; Wang, Chongmin; Chambers, Scott A; Du, Yingge

    2015-06-21

    We investigated the impact of crystallographic orientation on the photocatalytic activity of single crystalline WO3 thin films prepared by molecular beam epitaxy on the photodegradation of rhodamine B (RhB). A clear effect is observed, with (111) being the most reactive surface, followed by (110) and (001). Photoreactivity is directly correlated with the surface free energy determined by density functional theory calculations. The RhB photodegradation mechanism is found to involve hydroxyl radicals in solution formed from photo-generated holes and differs from previous studies performed on nanoparticles and composites.

  15. Role of activated chemisorption in gas-mediated electron beam induced deposition.

    PubMed

    Bishop, James; Lobo, Charlene J; Martin, Aiden; Ford, Mike; Phillips, Matthew; Toth, Milos

    2012-10-01

    Models of adsorbate dissociation by energetic electrons are generalized to account for activated sticking and chemisorption, and used to simulate the rate kinetics of electron beam induced chemical vapor deposition (EBID). The model predicts a novel temperature dependence caused by thermal transitions from physisorbed to chemisorbed states that govern adsorbate coverage and EBID rates at elevated temperatures. We verify these results by experiments that also show how EBID can be used to deposit high purity materials and characterize the rates and energy barriers that govern adsorption.

  16. How to produce high specific activity tin-117m using alpha particle beam.

    PubMed

    Duchemin, C; Essayan, M; Guertin, A; Haddad, F; Michel, N; Métivier, V

    2016-09-01

    Tin-117m is an interesting radionuclide for both diagnosis and therapy, thanks to the gamma-ray and electron emissions, respectively, resulting from its decay to tin-117g. The high specific activity of tin-117m is required in many medical applications, and it can be obtained using a high energy alpha particle beam and a cadmium target. The experiments performed at the ARRONAX cyclotron (Nantes, France) using an alpha particle beam delivered at 67.4MeV provide a measurement of the excitation function of the Cd-nat(α,x)Sn-117m reaction and the produced contaminants. The Cd-116(α,3n)Sn-117m production cross section has been deduced from these experimental results using natural cadmium. Both production yield and specific activity as a function of the projectile energy have been calculated. These informations help to optimize the irradiation conditions to produce tin-117m with the required specific activity using α particles with a cadmium target.

  17. Active control of a flexible smart beam using a system identification technique based on ARMAX

    NASA Astrophysics Data System (ADS)

    Bu, Xiongzhu; Ye, Lin; Su, Zhongqing; Wang, Chunhui

    2003-10-01

    A study on active vibration suppression for a flexible structural beam via a system identification approach was experimentally performed. The beam, incorporating a pair of piezoceramic transducers as actuators and a set of surface-bonded strain gauges as sensors, was evaluated. The relationship between the input control voltage applied on the actuators and the consequently induced strain, measured by the sensor, was then derived. An active control system, considering both the actuators and sensor, was configured using the ARMAX (auto-regressive moving average exogenous) model. A continuous signal with step waveform was selected as the input excitation. A digital-signal-processor-based real-time adaptive vibration control algorithm, supported by Agilent® E1415A, SCPs 1511 and SCPs 1532, was developed, and an algorithm was established using a pole placement control method, so as to achieve the desired closed-loop control. The effectiveness of the ARMAX model was examined by comparing it with the ARX (auto-regression with extra inputs) model. The results show good performance of the ARMAX model for system identification purposes and excellent effectiveness for active structural vibration control.

  18. Frequency and severity of injuries to operators during overturns of farm tractors.

    PubMed

    Cole, H P; Myers, M L; Westneat, S C

    2006-05-01

    Previous estimates of operator death from farm tractor overturn events range from 0.03 to 0.68. This study provided population-based estimates of the denominator of total farm tractor overturns and the frequency of six classes of overturn injury outcomes for tractors with and without rollover protective structures (ROPS). A 40-item telephone survey collected information from a random sample of 6,063 (8.0%) Kentucky farms about each farm's most recent overturn. A total of 551 (9.1%) farms reported overturns, and 5,512 (90.1%) reported no overturns. Injury outcomes for 443 overturns of non-ROPS tractors and 89 ROPS tractors were distributed as follows: no or minor injury (non-ROPS: 70.43%; ROPS: 82.02%), outpatient treatment (non-ROPS: 21.90%; ROPS: 9.00%), hospital admission (non-ROPS: 15.35%; ROPS: 3.37%), temporary disability (non-ROPS: 13.54%; ROPS: 14.61%), permanent disability (non-ROPS: 3.16%; ROPS: 0.00%), and death (non-ROPS: 5.42%; ROPS: 1.12%). (Percents total to more than 100 because some operators treated as outpatients were subsequently hospitalized, disabled, or died.) The observed 0.054 probability of death from overturn of non-ROPS tractors in this sample was corrected for the proportion of farms that went out of business prior to the survey and thus were excluded from the sampling frame. The adjusted 0.08 probability of death from overturn of a non-ROPS tractor is five times smaller than the NIOSH estimate of 0.40. The discrepancy lies in the much larger denominator of all non-fatal and fatal overturns than assumed previously. PMID:16724789

  19. Heavy and Overweight Vehicle Brake Testing: Five-Axle Combination Tractor-Flatbed Final Report

    SciTech Connect

    Lascurain, Mary Beth; Capps, Gary J; Franzese, Oscar

    2013-10-01

    The Federal Motor Carrier Safety Administration, in coordination with the Federal Highway Administration, sponsored the Heavy and Overweight Vehicle Brake Testing (HOVBT) program in order to provide information about the effect of gross vehicle weight (GVW) on braking performance. Because the Federal Motor Carrier Safety Regulations limit the number of braking system defects that may exist for a vehicle to be allowed to operate on the roadways, the examination of the effect of brake defects on brake performance for increased loads is also relevant. The HOVBT program seeks to provide relevant information to policy makers responsible for establishing load limits, beginning with providing test data for a combination tractor/trailer. This testing was conducted on a five-axle combination vehicle with tractor brakes meeting the Reduced Stopping Distance requirement rulemaking. This report provides a summary of the testing activities, the results of various analyses of the data, and recommendations for future research. Following a complete brake rebuild, instrumentation, and brake burnish, stopping tests were performed from 20 and 40 mph with various brake application pressures (15 psi, 25 psi, 35 psi, 45 psi, 55 psi, and full system pressure). These tests were conducted for various brake conditions at the following GVWs: 60,000, 80,000, 91,000, 97,000, 106,000, and 116,000 lb. The 80,000-lb GVWs included both balanced and unbalanced loads. The condition of the braking system was also varied. To introduce these defects, brakes (none, forward drive axle, or rear trailer axle) were made inoperative. In addition to the stopping tests, performance-based brake tests were conducted for the various loading and brake conditions. Analysis of the stopping test data showed the stopping distance to increase with load (as expected) and also showed that more braking force was generated by the drive axle brakes than the trailer axle brakes. The constant-pressure stopping test data

  20. Effect of N+ Beam Exposure on Superoxide Dismutase and Catalase Activities and Induction of Mn-SOD in Deinococcus Radiodurans

    NASA Astrophysics Data System (ADS)

    Song, Dao-jun; Chen, Ruo-lei; Shao, Chun-lin; Wu, Li-jun; Yu, Zeng-liang

    2000-10-01

    Though bacteria of the radiation-resistant Deinococcus radiodurans have a high resistance to the lethal and mutagenic effects of many DNA-damaging agents, the mechanisms involved in the response of these bacteria to oxidative stress are poorly understood. In this report, the superoxide dismutase (SOD) and catalase (CAT) activities produced by these bacteria were measured, and the change of SOD and CAT activities by 20 keV N+ beam exposure was examined. Their activities were increased by N+ beam exposure from 8×1014 ions/cm2 to 6×1015 ions/cm2. The treatment of H2O2 and [CHCl3 +CH3CH2OH] and the measurement of absorption spectrum showed that the increase in SOD activity was resulted from inducible activities of Mn-SOD in D. radiodurans AS1.633 by N+ beam exposure. These results suggested that this bacteria possess inducible defense mechanisms against the deleterious effects of oxidization.

  1. Semi-active control of a sandwich beam partially filled with magnetorheological elastomer

    NASA Astrophysics Data System (ADS)

    Dyniewicz, Bartłomiej; Bajkowski, Jacek M.; Bajer, Czesław I.

    2015-08-01

    The paper deals with the semi-active control of vibrations of structural elements. Elastomer composites with ferromagnetic particles that act as magnetorheological fluids are used. The damping coefficient and the shear modulus of the elastomer increases when it is exposed to an electro-magnetic field. The control of this process in time allows us to reduce vibrations more effectively than if the elastomer is permanently exposed to a magnetic field. First the analytical solution for the vibrations of a sandwich beam filled with an elastomer is given. Then the control problem is defined and applied to the analytical formula. The numerical solution of the minimization problem results in a periodic, perfectly rectangular control function if free vibrations are considered. Such a temporarily acting magnetic field is more efficient than a constantly acting one. The surplus reaches 20-50% or more, depending on the filling ratio of the elastomer. The resulting control was verified experimentally in the vibrations of a cantilever sandwich beam. The proposed semi-active control can be directly applied to engineering vibrating structural elements, for example helicopter rotors, aircraft wings, pads under machines, and vehicles.

  2. Active suppression of a beam under a moving mass using a pointwise fiber Bragg grating displacement sensing system.

    PubMed

    Chuang, Kuo-Chih; Ma, Chien-Ching; Wu, Rong-Hua

    2012-10-01

    This paper investigates active vibration control of a beam under a moving mass using a pointwise fiber Bragg grating (FBG) displacement sensing system. Dynamic responses of the proposed FBG displacement sensor are demodulated with an FBG filter and verified with measurement results obtained from a noncontact fiber-optic displacement sensor. System identification of the beam is first performed with a piezoceramic actuator and positive position feedback (PPF) controllers are designed based on the identified results. Then, transient responses of the beam under a moving mass with different moving conditions are measured using the FBG displacement sensor. A high-speed camera is used to detect the speed of the moving mass for further discussions about its influence on the transient response. Finally, active vibration control of the beam under the moving mass is performed and fast Fourier transform (FFT) as well as short-time Fourier transform (STFT) are employed to demonstrate control performances. For the case in which a rolling steel ball is directed from a slide to the beam to generate the moving mass, reductions of the vibration up to 50% and 60% are achieved in the frequency domain for the first and second modes of the beam, respectively. Based on the control experiments on the smallscale beam, results in this work show that the proposed FBG displacement sensing system can be used in research on the moving mass problem. PMID:23143564

  3. Investigations of electron helicity in optically active molecules using polarized beams of electrons and positrons

    NASA Technical Reports Server (NTRS)

    Gidley, D. W.; Rich, A.; Van House, J. C.; Zitzewitz, P. W.

    1981-01-01

    A positronium-formation experiment with a high sensitivity to a possible relation between the helicity of beta particles emitted in nuclear beta decay and the optical asymmetry of biological molecules is presented. The experiment is based on a mechanism in which the electrons in optically active molecules possess a helicity of less than 0.001, too weak to detect in radiolysis experiments, the sign of which depends on the chirality of the isomer. A helicity-dependent asymmetry is sought in the formation of the triplet ground state of positronium when a low-energy beam of polarized positrons of reversible helicity interacts with an optically active substance coating a channel electron multiplier. Asymmetries between positronium decays observed at positive and negative helicities for the same substance can thus be determined with a sensitivity of 0.0001, which represents a factor of 100 improvement over previous positronium experiments.

  4. RANS simulations of a simplified tractor/trailer geometry.

    SciTech Connect

    Roy, Christopher John; McWherter-Payne, Mary Anna; Salari, Kambiz; Payne, Jeffrey L.

    2003-07-01

    Steady-state Reynolds-averaged Navier-Stokes (RANS) simulations are presented for the three-dimensional flow over a simplified tractor/trailer geometry at zero degrees yaw angle. The simulations are conducted using a multi-block, structured computational fluid dynamics (CFD) code. The turbulence closure model employed is the two-equation Menter k-{omega} model. The discretization error is estimated by employing two grid levels: a fine mesh of 20 million cells and a coarser mesh of 2.5 million cells. Simulation results are compared to experimental data obtained at the NASA-Ames 7 x 10 ft wind tunnel. Quantities compared include vehicle drag, surface pressures, and time-averaged velocities in the trailer near wake. The results indicate that the RANS approach is able to accurately predict the surface pressure on the vehicle, with the exception of the base region. The pressure predictions in the base region are poor due to the inability of the RANS model to accurately capture the near-wake vortical structure. However, the gross pressure levels in the base region are in reasonable agreement with experiment, and thus the overall vehicle drag is well predicted.

  5. A Kalman filter implementation for precision improvement in low-cost GPS positioning of tractors.

    PubMed

    Gomez-Gil, Jaime; Ruiz-Gonzalez, Ruben; Alonso-Garcia, Sergio; Gomez-Gil, Francisco Javier

    2013-01-01

    Low-cost GPS receivers provide geodetic positioning information using the NMEA protocol, usually with eight digits for latitude and nine digits for longitude. When these geodetic coordinates are converted into Cartesian coordinates, the positions fit in a quantization grid of some decimeters in size, the dimensions of which vary depending on the point of the terrestrial surface. The aim of this study is to reduce the quantization errors of some low-cost GPS receivers by using a Kalman filter. Kinematic tractor model equations were employed to particularize the filter, which was tuned by applying Monte Carlo techniques to eighteen straight trajectories, to select the covariance matrices that produced the lowest Root Mean Square Error in these trajectories. Filter performance was tested by using straight tractor paths, which were either simulated or real trajectories acquired by a GPS receiver. The results show that the filter can reduce the quantization error in distance by around 43%. Moreover, it reduces the standard deviation of the heading by 75%. Data suggest that the proposed filter can satisfactorily preprocess the low-cost GPS receiver data when used in an assistance guidance GPS system for tractors. It could also be useful to smooth tractor GPS trajectories that are sharpened when the tractor moves over rough terrain. PMID:24217355

  6. A Kalman Filter Implementation for Precision Improvement in Low-Cost GPS Positioning of Tractors

    PubMed Central

    Gomez-Gil, Jaime; Ruiz-Gonzalez, Ruben; Alonso-Garcia, Sergio; Gomez-Gil, Francisco Javier

    2013-01-01

    Low-cost GPS receivers provide geodetic positioning information using the NMEA protocol, usually with eight digits for latitude and nine digits for longitude. When these geodetic coordinates are converted into Cartesian coordinates, the positions fit in a quantization grid of some decimeters in size, the dimensions of which vary depending on the point of the terrestrial surface. The aim of this study is to reduce the quantization errors of some low-cost GPS receivers by using a Kalman filter. Kinematic tractor model equations were employed to particularize the filter, which was tuned by applying Monte Carlo techniques to eighteen straight trajectories, to select the covariance matrices that produced the lowest Root Mean Square Error in these trajectories. Filter performance was tested by using straight tractor paths, which were either simulated or real trajectories acquired by a GPS receiver. The results show that the filter can reduce the quantization error in distance by around 43%. Moreover, it reduces the standard deviation of the heading by 75%. Data suggest that the proposed filter can satisfactorily preprocess the low-cost GPS receiver data when used in an assistance guidance GPS system for tractors. It could also be useful to smooth tractor GPS trajectories that are sharpened when the tractor moves over rough terrain. PMID:24217355

  7. Complementing computationally predicted regulatory sites in Tractor_DB using a pattern matching approach.

    PubMed

    Guía, Marylens Hernández; Pérez, Abel González; Angarica, Vladimir Espinosa; Vasconcelos, Ana T; Collado-Vides, Julio

    2005-01-01

    Prokaryotic genomes annotation has focused on genes location and function. The lack of regulatory information has limited the knowledge on cellular transcriptional regulatory networks. However, as more phylogenetically close genomes are sequenced and annotated, the implementation of phylogenetic footprinting strategies for the recognition of regulators and their regulons becomes more important. In this paper we describe a comparative genomics approach to the prediction of new gamma-proteobacterial regulon members. We take advantage of the phylogenetic proximity of Escherichia coli and other 16 organisms of this subdivision and the intensive search of the space sequence provided by a pattern-matching strategy. Using this approach we complement predictions of regulatory sites made using statistical models currently stored in Tractor_DB, and increase the number of transcriptional regulators with predicted binding sites up to 86. All these computational predictions may be reached at Tractor_DB (www.bioinfo.cu/Tractor_DB, www.tractor.lncc.br, www.ccg.unam.mx/Computational_Genomics/tractorDB/). We also take a first step in this paper towards the assessment of the conservation of the architecture of the regulatory network in the gamma-proteobacteria through evaluating the conservation of the overall connectivity of the network. PMID:15972018

  8. A Kinematically Beamed, Low Energy Pulsed Neutron Source for Active Interrogation

    SciTech Connect

    Dietrich, D; Hagmann, C; Kerr, P; Nakae, L; Rowland, M; Snyderman, N; Stoeffl, W; Hamm, R

    2004-10-07

    We are developing a new active interrogation system based on a kinematically focused low energy neutron beam. The key idea is that one of the defining characteristics of SNM (Special Nuclear Materials) is the ability for low energy or thermal neutrons to induce fission. Thus by using low energy neutrons for the interrogation source we can accomplish three goals, (1) Energy discrimination allows us to measure the prompt fast fission neutrons produced while the interrogation beam is on; (2) Neutrons with an energy of approximately 60 to 100 keV do not fission 238U and Thorium, but penetrate bulk material nearly as far as high energy neutrons do and (3) below about 100keV neutrons lose their energy by kinematical collisions rather than via the nuclear (n,2n) or (n,n') processes thus further simplifying the prompt neutron induced background. 60 keV neutrons create a low radiation dose and readily thermal capture in normal materials, thus providing a clean spectroscopic signature of the intervening materials. The kinematically beamed source also eliminates the need for heavy backward and sideway neutron shielding. We have designed and built a very compact pulsed neutron source, based on an RFQ proton accelerator and a lithium target. We are developing fast neutron detectors that are nearly insensitive to the ever-present thermal neutron and neutron capture induced gamma ray background. The detection of only a few high energy fission neutrons in time correlation with the linac pulse will be a clear indication of the presence of SNM.

  9. 29 CFR 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002 as appropriate. A ROPS used on track-type tractors shall meet the test and performance requirements of 29 CFR... seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. (ii)...

  10. 29 CFR 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002 as appropriate. A ROPS used on track-type tractors shall meet the test and performance requirements of 29 CFR..., vineyards or hop yards where the vertical clearance requirements would substantially interfere with...

  11. Beam diagnostics

    SciTech Connect

    Bogaty, J.; Clifft, B.E.; Zinkann, G.P.; Pardo, R.C.

    1995-08-01

    The ECR-PII injector beam line is operated at a fixed ion velocity. The platform high voltage is chosen so that all ions have a velocity of 0.0085c at the PII entrance. If a previous tune configuration for the linac is to be used, the beam arrival time must be matched to the previous tune as well. A nondestructive beam-phase pickup detector was developed and installed at the entrance to the PII linac. This device provides continuous phase and beam current information and allows quick optimization of the beam injected into PII. Bunches traverse a short tubular electrode thereby inducing displacement currents. These currents are brought outside the vacuum interface where a lumped inductance resonates electrode capacitance at one of the bunching harmonic frequencies. This configuration yields a basic sensitivity of a few hundred millivolts signal per microampere of beam current. Beam-induced radiofrequency signals are summed against an offset frequency generated by our master oscillator. The resulting kilohertz difference frequency conveys beam intensity and bunch phase information which is sent to separate processing channels. One channel utilizes a phase locked loop which stabilizes phase readings if beam is unstable. The other channel uses a linear full wave active rectifier circuit which converts kilohertz sine wave signal amplitude to a D.C. voltage representing beam current. A prototype set of electronics is now in use with the detector and we began to use the system in operation to set the arrival beam phase. A permanent version of the electronics system for the phase detector is now under construction. Additional nondestructive beam intensity and phase monitors at the {open_quotes}Booster{close_quotes} and {open_quotes}ATLAS{close_quotes} linac sections are planned as well as on some of the high-energy beam lines. Such a monitor will be particularly useful for FMA experiments where the primary beam hits one of the electric deflector plates.

  12. 100 s extraction of negative ion beams by using actively temperature-controlled plasma grid

    SciTech Connect

    Kojima, A. Hanada, M.; Yoshida, M.; Tobari, H.; Kashiwagi, M.; Umeda, N.; Watanabe, K.; Grisham, L. R.

    2014-02-15

    Long pulse beam extraction with a current density of 120 A/m{sup 2} for 100 s has been achieved with a newly developed plasma grid (PG) for the JT-60SA negative ion source which is designed to produce high power and long pulse beams with a negative ion current of 130 A/m{sup 2} (22 A) and a pulse length of 100 s. The PG temperature is regulated by fluorinated fluids in order to keep the high PG temperature for the cesium-seeded negative ion production. The time constant for temperature controllability of the PG was measured to be below 10 s, which was mainly determined by the heat transfer coefficient of the fluorinated fluid. The measured decay time of the negative ion current extracted from the actively temperature-controlled PG was 430 s which was sufficient for the JT-60SA requirement, and much longer than that by inertial-cooling PG of 60 s. Obtained results of the long pulse capability are utilized to design the full size PG for the JT-60SA negative ion source.

  13. Power beam technology at Los Alamos/A review of research and development activities

    SciTech Connect

    Casey, H.

    1990-01-01

    This document discusses techniques and research programs in power beam welding at Los Alamos National Laboratories. Specific areas discussed are in plasma welding, electron beam welding and laser welding. 11 refs., 9 figs. (FSD)

  14. Tractor-trailer driver fatality: the role of nonconsecutive rest in a sleeper berth.

    PubMed

    Hertz, R P

    1988-12-01

    Federal regulation allows truck drivers to use sleeper berths to accumulate eight hours of off-duty rest in two separate periods. Because sleep disruption may cause fatigue and deterioration of performance, a study was conducted to evaluate the association between sleeper-berth use in two periods and tractor-trailer driver fatality. Using Bureau of Motor Carrier Safety Reports, crashes that resulted in tractor-trailer driver fatality were compared with property damage crashes. After adjusting for confounding variables by logistic regression, tractor-trailer driver fatality was found to be significantly associated with sleeper-berth use in two shifts (odds ratio = 3.05). Statistically significant but weaker associations were found between driver fatality and rural district, night driving, gross vehicle weight of 72,000 pounds or more, single-vehicle collision, intercity trip, and employment on an occasional basis.

  15. A Study of the Effect of Preschool Children's Participation in Sensorimotor Activities on Their Understanding of the Mechanical Equilibrium of a Balance Beam

    ERIC Educational Resources Information Center

    Hadzigeorgiou, Yannis; Anastasiou, Leonidas; Konsolas, Manos; Prevezanou, Barbara

    2009-01-01

    The purpose of this study was to investigate whether participation in sensorimotor activities by preschool children involving their own bodily balance while walking on a beam over the floor has an effect on their understanding of the mechanical equilibrium of a balance beam. The balance beam consisted of a horizontal stick balancing around its…

  16. Prompt gamma activation analysis of boron in reference materials using diffracted polychromatic neutron beam

    NASA Astrophysics Data System (ADS)

    Byun, S. H.; Sun, G. M.; Choi, H. D.

    2004-01-01

    Boron concentrations were analyzed for standard reference materials by prompt gamma activation analysis (PGAA). The measurements were performed at the SNU-KAERI PGAA facility installed at Hanaro, the research reactor of Korea Atomic Energy Research Institute (KAERI). The facility uses a diffracted polychromatic beam with a neutron flux of 7.9 × 10 7 n/cm 2 s. Elemental sensitivity for boron was calibrated from the prompt gamma-ray spectra of boric acid samples containing 2-45 μg boron. The sensitivity of 2131 cps/mg-B was obtained from the linearity of the boron peak count rate versus the boron mass. The detection limit for boron was estimated to be 67 ng from an empty sample bag spectrum for a counting time of 10,000 s. The measured boron concentrations for standard reference materials showed good consistency with the certified or information values.

  17. Ion Beam Deflection (AKA Push-Me/Pull-You)

    NASA Technical Reports Server (NTRS)

    Brophy, John

    2013-01-01

    The Ion Beam Deflection provides the following potential advantages over other asteroid deflection systems. Like the gravity tractor, it doesn't require despinning of the asteroid. Unlike the gravity tractor, it provides a significantly higher coupling force that is independent of the asteroid size. The concept could be tested as part of the baseline Asteroid Redirect Robotic Mission. The thrust and total impulse are entirely within the design of the SEP vehicle. The total impulse is potentially competitive with kinetic impactors and eliminates the need for a second rendezvous spacecraft.?Gridded ion thrusters provide beam divergence angles of a few degrees enabling long stand-off distances from the asteroid. Mitigating control issues. Minimizing back-sputter contamination risks

  18. Design of active temperature compensated composite free-free beam MEMS resonators in a standard process

    NASA Astrophysics Data System (ADS)

    Xereas, George; Chodavarapu, Vamsy P.

    2014-03-01

    Frequency references are used in almost every modern electronic device including mobile phones, personal computers, and scientific and medical instrumentation. With modern consumer mobile devices imposing stringent requirements of low cost, low complexity, compact system integration and low power consumption, there has been significant interest to develop batch-manufactured MEMS resonators. An important challenge for MEMS resonators is to match the frequency and temperature stability of quartz resonators. We present 1MHz and 20MHz temperature compensated Free-Free beam MEMS resonators developed using PolyMUMPS, which is a commercial multi-user process available from MEMSCAP. We introduce a novel temperature compensation technique that enables high frequency stability over a wide temperature range. We used three strategies: passive compensation by using a structural gold (Au) layer on the resonator, active compensation through using a heater element, and a Free-Free beam design that minimizes the effects of thermal mismatch between the vibrating structure and the substrate. Detailed electro-mechanical simulations were performed to evaluate the frequency response and Quality Factor (Q). Specifically, for the 20MHz device, a Q of 10,000 was obtained for the passive compensated design. Finite Element Modeling (FEM) simulations were used to evaluate the Temperature Coefficient of frequency (TCf) of the resonators between -50°C and 125°C which yielded +0.638 ppm/°C for the active compensated, compared to -1.66 ppm/°C for the passively compensated design and -8.48 ppm/°C for uncompensated design for the 20MHz device. Electro-thermo-mechanical simulations showed that the heater element was capable of increasing the temperature of the resonators by approximately 53°C with an applied voltage of 10V and power consumption of 8.42 mW.

  19. Towing Asteroids with Gravity Tractors Enhanced by Tethers and Solar Sails

    NASA Technical Reports Server (NTRS)

    Shen, Haijun; Roithmayr, Carlos M.

    2015-01-01

    Material collected from an asteroid's surface can be used to increase gravitational attraction between the asteroid and a Gravity Tractor (GT); the spacecraft therefore operates more effectively and is referred to as an Enhanced Gravity Tractor (EGT). The use of tethers and solar sails to further improve effectiveness and simplify operations is investigated. By employing a tether, the asteroidal material can be placed close to the asteroid while the spacecraft is stationed farther away, resulting in a better safety margin and improved thruster efficiency. A solar sail on a spacecraft can naturally provide radial offset and inter-spacecraft separation required for multiple EGTs.

  20. A three body dynamic simulation of a seated tractor rocket escape system for the Space Shuttle

    NASA Technical Reports Server (NTRS)

    Ondler, R. M.

    1989-01-01

    In the tractor-rocket seated-extraction candidate system for Space Shuttle Orbiter crew escape, the crewmember is pulled from his seat and away from the Orbiter via an elastic pendant, using a system of rails to guide the extraction trajectory through an opening on the window frame for flight deck crew and through the side hatch for the middeck crew. A three-body simulation has been developed to model the flight-mechanics aspects of the concept, where the three bodies are the astronaut (six DOF), the tractor rocket (six DOF), and the Shuttle Orbiter (three DOF); attention is given to crewmembers' clearance of the Orbiter structure and engine plumes.

  1. Biological effects of passive versus active scanning proton beams on human lung epithelial cells.

    PubMed

    Gridley, Daila S; Pecaut, Michael J; Mao, Xiao W; Wroe, Andrew J; Luo-Owen, Xian

    2015-02-01

    The goal was to characterize differences in cell response after exposure to active beam scanning (ABS) protons compared to a passive delivery system. Human lung epithelial (HLE) cells were evaluated at various locations along the proton depth dose profile. The dose delivered at the Bragg peak position was essentially identical (∼4 Gy) with the two techniques, but depth dose data showed that ABS resulted in lower doses at entry and more rapid drop-off after the peak. Average dose rates for the passive and ABS beams were 1.1 Gy/min and 5.1 Gy/min, respectively; instantaneous dose rates were 19.2 Gy/min and 2,300 Gy/min (to a 0.5 × 0.5 mm(2) voxel). Analysis of DNA synthesis was based on (3)H-TdR incorporation. Quantitative real-time polymerase chain reaction (RT-PCR) was done to determine expression of genes related to p53 signaling and DNA damage; a total of 152 genes were assessed. Spectral karyotyping and analyses of the Golgi apparatus and cytokines produced by the HLE cells were also performed. At or near the Bragg peak position, ABS protons resulted in a greater decrease in DNA synthesis compared to passively delivered protons. Genes with >2-fold change (P < 0.05 vs. 0 Gy) after passive proton irradiation at one or more locations within the Bragg curve were BTG2, CDKN1A, IFNB1 and SIAH1. In contrast, many more genes had >2-fold difference with ABS protons: BRCA1, BRCA2, CDC25A, CDC25C, CCNB2, CDK1, DMC1, DNMT1, E2F1, EXO1, FEN1, GADD45A, GTSE1, IL-6, JUN, KRAS, MDM4, PRC1, PTTG1, RAD51, RPA1, TNF, WT1, XRCC2, XRCC3 and XRCC6BP1. Spectral karyotyping revealed numerous differences in chromosomal abnormalities between the two delivery systems, especially at or near the Bragg peak. Percentage of cells staining for the Golgi apparatus was low after exposure to passive and active proton beams. Studies such as this are needed to ensure patient safety and make modifications in ABS delivery, if necessary.

  2. Evaluation of Corrosion Failure in Tractor-Trailer Brake System

    SciTech Connect

    Wilson, DF

    2002-10-22

    As reported to ORNL, concomitant with the introduction of different deicing and anti-icing compounds, there was an increase in the brake failure rate of tractor-trailer trucks. A forensic evaluation of a failed brake system was performed. Optical and scanning electron microscopic evaluation showed corrosion to be mostly confined to the brake table/lining interface. The corrosion is non-uniform as is to be expected for plain carbon steel in chloride environments. This initial analysis found no evidence for the chlorides of calcium and magnesium, which are the newly introduced deicing and antiicing compounds and are less soluble in water than the identified chlorides of sodium and potassium, in the scale. The result could be as a result of non-exposure of the examined brake table to calcium and magnesium chloride. The mechanisms for the increased failure rate are postulated as being an increased rate of corrosion due to positive shifts in the corrosion potential, and an increased amount of corrosion due to an increased ''time of wetness'' that results from the presence of hygroscopic salts. Laboratory scale evaluation of the corrosion of plain carbon steel in simulated deicing and anti-icing solutions need to be performed to determine corrosion rates and morphological development of corrosion product, to compare laboratory data to in-service data, and to rank economically feasible replacement materials for low carbon steel. In addition, the mechanical behavior of the lining attached to the brake shoe table needs to be assessed. It is opined that an appropriate adjustment of materials could easily allow for a doubling of a brake table/lining lifetime. Suggestions for additional work, to clarify the mechanisms of rust jacking and to develop possible solutions, are described.

  3. Progress toward a microsecond duration, repetitive, intense-ion beam for active spectroscopic measurements on ITER

    SciTech Connect

    Davis, H.A.; Bartsch, R.R.; Barnes, C.W.

    1996-06-01

    The authors describe the design of an intense, pulsed, repetitive, neutral beam based on magnetically insulated diode technology for injection into ITER for spectroscopic measurements of thermalizing alpha particle and thermal helium density profiles, ion temperature, plasma rotation, and low Z impurity concentrations in the confinement region. The beam is being developed to enhance low signal-to-noise ratios expected with conventional steady-state ion beams because of severe beam attenuation and intense bremstrahlung emission. A 5 GW (e.g., 100 keV, 50 kA) one-microsecond-duration beam would increase the signal by 10{sup 3} compared to a conventional 5 MW beam with signal-to-noise ratios comparable to those from a chopped conventional beam in one second.

  4. A practical fan-beam design and reconstruction algorithm for Active and Passive Computed Tomography of radioactive waste barrels

    NASA Astrophysics Data System (ADS)

    Roy, Tushar; More, M. R.; Ratheesh, Jilju; Sinha, Amar

    2015-09-01

    Active and Passive CT (A&PCT) of waste barrels is mostly carried out in parallel beam configuration due to its relative ease of implementation. This necessitates either using a single detector-source pair and translating the barrel or using multiple detector-source pairs for increasing the scanning speed. Additionally, because the use of bulky HPGe detectors may limit the number of detectors used in both active and passive modes, we propose to use 1″×1″ LaBr3(Ce) scintillators. This paper describes a practical fan-beam reconstruction for A&PCT imaging of waste barrels. A fan beam system model has been computed analytically and reconstruction done using MLEM algorithm. The results are compared with analytical reconstruction.

  5. 78 FR 7394 - Foreign-Trade Zone 41-Milwaukee, WI; Notification of Proposed Production Activity; CNH America...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-01

    ... Foreign-Trade Zones Board Foreign-Trade Zone 41--Milwaukee, WI; Notification of Proposed Production... Milwaukee, grantee of FTZ 41, submitted a notification of proposed production activity on behalf of CNH... are used for the production of tractors and tractor/combine components. Pursuant to 15 CFR...

  6. A History of the Caterpillar Tractor Company's Use of Motion Pictures.

    ERIC Educational Resources Information Center

    Veeder, Gerry A.

    Film historians have tended to overlook the industrial film even though it has been widely used as a sales tool since early in this century. The Caterpillar Tractor Company was one of the first to adopt this medium as a means of demonstrating what its machines could do in a variety of situations. While other types of films have been made by…

  7. The Development of Procedural Knowledge in Adults Engaged in a Tractor-Trailer Task.

    ERIC Educational Resources Information Center

    Moses, Nelson

    1994-01-01

    Studied development of procedural knowledge in 14 adults, aged 18 to 35 years, engaged in a novel task using a toy tractor-trailer rig. Results revealed three phases of development in subjects' knowledge of steering procedures and the rig's movement patterns, and their use of feedback information. Subjects also manifested different levels of…

  8. GASOLINE TRACTOR ENGINE SYSTEMS. AGRICULTURAL MACHINERY--SERVICE OCCUPATIONS, MODULE NUMBER 14.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center for Vocational and Technical Education.

    ONE OF A SERIES DESIGNED TO HELP TEACHERS PREPARE POSTSECONDARY STUDENTS FOR AGRICULTURAL MACHINERY SERVICE OCCUPATIONS AS PARTS MEN, MECHANICS, MECHANIC'S HELPERS, AND SERVICE SUPERVISORS, THIS GUIDE AIMS TO DEVELOP STUDENT UNDERSTANDING OF THE OPERATION, COMPONENTS, AND FUNCTIONS OF VARIOUS GASOLINE TRACTOR ENGINE SYSTEMS. IT WAS DEVELOPED BY A…

  9. 49 CFR 399.207 - Truck and truck-tractor access requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or... equipped on each side of the vehicle where a seat is located, with a sufficient number of steps and... vehicle at unladen weight. (2) Distance between steps. The distance between steps, up to and including...

  10. 49 CFR 399.207 - Truck and truck-tractor access requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or... equipped on each side of the vehicle where a seat is located, with a sufficient number of steps and... vehicle at unladen weight. (2) Distance between steps. The distance between steps, up to and including...

  11. Analysis of bifurcation and stability for a tractor semi-trailer in planar motion

    NASA Astrophysics Data System (ADS)

    Ding, Nenggen; Shi, Xiaobo; Zhang, Yipeng; Chen, Wen

    2014-12-01

    This paper is intended for bifurcation analysis of a nonlinear tractor semi-trailer vehicle model in planar motion and for investigating its stability under constant running conditions. Bifurcation analysis shows that bifurcation diagrams of a tractor semi-trailer are quite different from those of a single-unit vehicle. Some instability phenomena of the vehicle system such as jackknifing, sideslip, and spinning are explained by correlating them with the behaviour in the neighbourhood of unstable fixed points based on analysis of eigenvectors, phase trajectories, and status of lateral tyre force saturation. It is also found that yaw planar instability of a tractor semi-trailer is caused by lateral tyre force saturation of the tractor's rear axles and/or the trailer's axles. Moreover, the stability region in the state space is demarcated, and a stability index for evaluating size of the stability region in a feasible domain is proposed. Yaw stability under constant driving conditions is analysed by using the proposed stability index.

  12. Vocational Agriculture Training Program: Safe Tractor and Farm Machinery Operation. Special Paper No. 8. Second Revision.

    ERIC Educational Resources Information Center

    Bobbitt, Frank; Doss, Howard

    The publication was prepared for the United States Office of Education for use by teachers who direct agricultural training programs in safe tractor operation and safe farm machinery operation that comply with the United States Department of Labor regulations on hazardous occupations in agriculture. Upon successful completion of these training…

  13. Self-Pacing a Gross Motor Skills Course: Crawler Tractor Operator, MOS 62E20.

    ERIC Educational Resources Information Center

    Brennan, Mark F.; Taylor, John E.

    As part of the Army's emphasis on performance-oriented instruction in training centers, a study was conducted to determine the feasibility of using self-paced instruction in a gross motor skills course. The Crawler Tractor Operator Course, a seven-week heavy equipment course conducted at Fort Leonard Wood, Missouri was selected for the study…

  14. Purposeful Co-Curricular Activities Designed to Increase Engagement: A Practice Brief Based on BEAMS Project Outcomes

    ERIC Educational Resources Information Center

    Hazeur, Camille

    2008-01-01

    One of a series highlighting key practices undertaken by some of the many successful BEAMS (Building Engagement and Attainment for Minority Students) schools during the project's five years of data collection and action plan implementation, this practice brief demonstrates how emphasis on co-curricular activities can ultimately result in increased…

  15. Evaluation of a tractor cab using real-time aerosol counting instrumentation.

    PubMed

    Hall, Ronald M; Heitbrink, William A; Reed, Laurence D

    2002-01-01

    Aerosol instrumentation was used to evaluate air infiltration into tractor cabs that are used to protect the agricultural worker during pesticide applications. Preliminary surveys were conducted on three different manufactured agriculture enclosures. The results of these preliminary surveys indicated that aerosols are entering the cab through leak sources or are being generated inside the cab. These results identified the need for in-depth field evaluations of tractor cabs to identify any leak sources. To evaluate the ability of tractor cabs to reduce operator air contaminant exposure, field evaluations were conducted on two tractor cabs. Specifically, we evaluated: 1) the particle size distribution and the effectiveness of the filter system; and 2) air infiltration into the cab. These evaluations were also conducted to demonstrate the ease and practicality of using optical particle counters to evaluate the ability of cabin filtration systems. Pesticide particle size distribution during an air blast spray operation was also evaluated during the study. The field tests were conducted on a John Deere 7000 series tractor cab (tractor manufacturer's cab) and a Nelson spraycab (retrofit cab). Both cabs were equipped with high efficiency particulate air (HEPA) filter media which were assumed to be 99.97 percent efficient at removing the test aerosol, atmospheric condensation nuclei. Thus, the major source of aerosols inside the cab was assumed to be leakage around filters at the seals. Using a portable dust monitor (PDM), the ratio of the outside to inside aerosol measurements was used to calculate a cab protection factor. During the evaluations, one PDM was placed inside the tractor cab (near the tractor operator) and one PDM was placed outside (near the air intake) to count particles. During the evaluations, the instruments were switched to prevent instrument bias from affecting the findings. The ratio of the two measurements (i.e., protection factor = outside

  16. Optimizing 50kV hydrogen diagnostic neutral beam performance for active spectroscopy in MST

    NASA Astrophysics Data System (ADS)

    Feng, X.; Boguski, J.; Craig, D.; den Hartog, D. J.; Munaretto, S.; Nornberg, M. D.; Olivia, S.

    2015-11-01

    The 50 kV hydrogen diagnostic neutral beam on MST provides local measurements of impurity ion emission through charge exchange recombination spectroscopy (CHERS) and of core-localized magnetic field through the motional Stark effect (MSE). The beam, which was designed to provide 5A of neutral current at 50 kV to meet these needs, is currently on a test stand to accommodate diagnosis, in order to increase the reliability of beam formation, sustain a steady current of 5 amps for 20ms, and optimize the primary energy fraction. The reliability of arc formation was increased from 40% to 80% success rate with increase of cathode gas pressure from 150kPa to 200kPa, and the stability of the arc current is improved with a decrease of the insulation magnetic field. A calorimeter with 5 thermocouples is installed to measure the horizontal and vertical beam profiles as well as beam divergence. Beam energy components are quantified through Doppler-shift spectroscopy. Preliminary simulation results of the beam using the ALCBEAM code as well as a description of how changes to the beam performance can affect CHERS and MSE measurements are presented. This work is supported by the U.S. DOE.

  17. High active nitrogen flux growth of GaN by plasma assisted molecular beam epitaxy

    SciTech Connect

    McSkimming, Brian M. Speck, James S.; Chaix, Catherine

    2015-09-15

    In the present study, the authors report on a modified Riber radio frequency (RF) nitrogen plasma source that provides active nitrogen fluxes more than 30 times higher than those commonly used for plasma assisted molecular beam epitaxy (PAMBE) growth of gallium nitride (GaN) and thus a significantly higher growth rate than has been previously reported. GaN films were grown using N{sub 2} gas flow rates between 5 and 25 sccm while varying the plasma source's RF forward power from 200 to 600 W. The highest growth rate, and therefore the highest active nitrogen flux, achieved was ∼7.6 μm/h. For optimized growth conditions, the surfaces displayed a clear step-terrace structure with an average RMS roughness (3 × 3 μm) on the order of 1 nm. Secondary ion mass spectroscopy impurity analysis demonstrates oxygen and hydrogen incorporation of 1 × 10{sup 16} and ∼5 × 10{sup 17}, respectively. In addition, the authors have achieved PAMBE growth of GaN at a substrate temperature more than 150 °C greater than our standard Ga rich GaN growth regime and ∼100 °C greater than any previously reported PAMBE growth of GaN. This growth temperature corresponds to GaN decomposition in vacuum of more than 20 nm/min; a regime previously unattainable with conventional nitrogen plasma sources. Arrhenius analysis of the decomposition rate shows that samples with a flux ratio below stoichiometry have an activation energy greater than decomposition of GaN in vacuum while samples grown at or above stoichiometry have decreased activation energy. The activation energy of decomposition for GaN in vacuum was previously determined to be ∼3.1 eV. For a Ga/N flux ratio of ∼1.5, this activation energy was found to be ∼2.8 eV, while for a Ga/N flux ratio of ∼0.5, it was found to be ∼7.9 eV.

  18. Active H ∞ control of the vibration of an axially moving cantilever beam by magnetic force

    NASA Astrophysics Data System (ADS)

    Wang, Liang; Chen, Huai-hai; He, Xu-dong

    2011-11-01

    An H ∞ method for the vibration control of an iron cantilever beam with axial velocity using the noncontact force by permanent magnets is proposed in the paper. The transverse vibration equation of the axially moving cantilever beam with a tip mass is derived by D'Alembert's principle and then updated by experiments. An experimental platform and a magnetic control system are introduced. The properties of the force between the magnet and the beam have been determined by theoretic analysis and tests. The H ∞ control strategy for the suppression of the beam transverse vibration by initial deformation excitations is put forward. The control method can be used for the beam with constant length or varying length. Numerical simulation and actual experiments are implemented. The results show that the control method is effective and the simulations fit well with the experiments.

  19. Vibration energy absorption in the whole-body system of a tractor operator.

    PubMed

    Szczepaniak, Jan; Tanaś, Wojciech; Kromulski, Jacek

    2014-01-01

    Many people are exposed to whole-body vibration (WBV) in their occupational lives, especially drivers of vehicles such as tractor and trucks. The main categories of effects from WBV are perception degraded comfort interference with activities-impaired health and occurrence of motion sickness. Absorbed power is defined as the power dissipated in a mechanical system as a result of an applied force. The vibration-induced injuries or disorders in a substructure of the human system are primarily associated with the vibration power absorption distributed in that substructure. The vibration power absorbed by the exposed body is a measure that combines both the vibration hazard and the biodynamic response of the body. The article presents measurement method for determining vibration power dissipated in the human whole body system called Vibration Energy Absorption (VEA). The vibration power is calculated from the real part of the force-velocity cross-spectrum. The absorbed power in the frequency domain can be obtained from the cross-spectrum of the force and velocity. In the context of the vibration energy transferred to a seated human body, the real component reflects the energy dissipated in the biological structure per unit of time, whereas the imaginary component reflects the energy stored/released by the system. The seated human is modeled as a series/parallel 4-DOF dynamic models. After introduction of the excitation, the response in particular segments of the model can be analyzed. As an example, the vibration power dissipated in an operator has been determined as a function of the agricultural combination operating speed 1.39 - 4.16 ms(-1). PMID:24959797

  20. An admittance function of active piezoelectric elements bonded on a cracked beam

    NASA Astrophysics Data System (ADS)

    Kuang, You-Di; Li, Guo-Qing; Chen, Chuan-Yao

    2006-11-01

    The electric admittance function of the piezoelectric patches bonded on a beam with an open crack is presented, for the purpose of theoretically evaluating the health conditions of the cracked beam. At first, a sandwich beam with two layers of piezoelectric actuators is regarded as a piezoelectric bimorph, and the dynamics of the bimorph is represented by a 5×5 piezoelectric impedance matrix. Secondly, the dynamics of the elastic beam is also represented by a 4×4 impedance matrix, which is a degenerative form of piezoelectric impedance. Thirdly, the open crack is modeled as rotational massless spring and an expression of the equivalent stiffness is adopted, then the spring is used to connect the adjacent elastic beam segments. Furthermore, the cracked beam is represented by three elastic beam segments and one piezoelectric bimorph segment together with one spring. The admittance function of the piezoelectric elements is obtained by solving the linear impedance equations considering the mechanical-electric boundary conditions and the continuum conditions between the beam segments and the spring. Lastly, the effects of the crack depth and location on the admittance are examined in two numeric examples. It is found that the frequency changes and the admittance amplitude changes of the beam due to the crack can be predicted by the piezoelectric admittance function, and the modal frequencies calculated by the proposed method are accord with the results obtained by experiments and other methods. The possible application of the admittance function to detect the crack on the beam is discussed at the end of the paper as well.

  1. Controlling Vector Bessel Beams with Metasurfaces

    NASA Astrophysics Data System (ADS)

    Pfeiffer, Carl; Grbic, Anthony

    2014-10-01

    Unprecedented control of an electromagnetic wave front is demonstrated with reflectionless metasurfaces that can manipulate vector Bessel beams: cylindrical vector beams with a Bessel profile. First, two metasurfaces are developed to convert linearly and circularly polarized Gaussian beams into vector Bessel beams. Each unit cell of the metasurfaces provides polarization and phase control with high efficiency. Next, the reciprocal process is demonstrated: an incident radially polarized Bessel beam is transformed into collimated, linearly and circularly polarized beams. In this configuration, a planar Bessel beam launcher is integrated with a collimating metasurface lens to realize a low-profile lens-antenna. The lens-antenna achieves a high directivity (exceeding 20 dB) with a subwavelength overall thickness. Finally, a metasurface providing isotropic polarization rotation is used to transform a radially polarized Bessel beam into an azimuthally polarized Bessel beam. This work demonstrates that metasurfaces can be used to generate arbitrary combinations of radial and azimuthal polarizations for applications such as focus shaping or generating tractor beams.

  2. The U.S. Department of Labor's Tractor and Machinery Certification Program: management styles and perceptions held by community stakeholders and instructors.

    PubMed

    Jepsen, S D

    2012-07-01

    A mixed-mode, descriptive study was conducted on the U.S. Department of Labor's (DOL) Tractor and Machinery Certification Program. Legislated by the Fair Labors Standards Act, the Hazardous Occupations Order in Agriculture (HOOA) was enacted in 1968 as a public policy measure to reduce the number of injuries to youth on farms. An educational exemption allows youth 14 and 15 years of age to work for hire after they successfully complete a training program. In the 40+ years since the legislation went into effect prescribing such training exemptions, deficiencies and variations have occurred in the quality of the educational program and the system by which agencies certify young people. To gain a better understanding of the DOL Tractor and Machinery Certification program, community stakeholders were asked to identify management practices, curriculum resources, and perceptions of the DOL program. The study design used qualitative data from 49 agricultural representatives participating in regional focus groups and quantitative data from 330 community instructors responding to an electronic-formatted questionnaire (representing a 70.7% response rate) in an effort to answer the question: "What is the current status of the DOL Tractor and Machinery Certification program in the United States?" The findings revealed that 55.2% of the instructors taught a qualifying DOL program. Of these, the certification was administered through an Extension or 4-H program (68.7%), an agricultural education program (24.7%), or as a combination of Extension and agricultural education (6.0%). Course instructors believed the training was beneficial to students and had opportunity to attract more students than currently enrolled These instructors placed a higher value on standardized teaching materials than on standardized testing procedures; they also supported the need for additional teaching aids, which included hands-on activities, videotapes, student workbooks, and DVDs. Study participants

  3. Active buckling control of an imperfect beam-column with circular cross-section using piezo-elastic supports and integral LQR control

    NASA Astrophysics Data System (ADS)

    Schaeffner, Maximilian; Platz, Roland

    2016-09-01

    For slender beam-columns loaded by axial compressive forces, active buckling control provides a possibility to increase the maximum bearable axial load above that of a purely passive structure. In this paper, the potential of active buckling control of an imperfect beam-column with circular cross-section using piezo-elastic supports is investigated numerically. Imperfections are given by an initial deformation of the beam-column caused by a constant imperfection force. With the piezo-elastic supports, active bending moments in arbitrary directions orthogonal to the beam-column's longitudinal axis can be applied at both beam- column's ends. The imperfect beam-column is loaded by a gradually increasing axial compressive force resulting in a lateral deformation of the beam-column. First, a finite element model of the imperfect structure for numerical simulation of the active buckling control is presented. Second, an integral linear-quadratic regulator (LQR) that compensates the deformation via the piezo-elastic supports is derived for a reduced modal model of the ideal beam-column. With the proposed active buckling control it is possible to stabilize the imperfect beam-column in arbitrary lateral direction for axial loads above the theoretical critical buckling load and the maximum bearable load of the passive structure.

  4. Apparatus and process for active pulse intensity control of laser beam

    DOEpatents

    Wilcox, Russell B.

    1992-01-01

    An optically controlled laser pulse energy control apparatus and process is disclosed wherein variations in the energy of a portion of the laser beam are used to vary the resistance of a photodetector such as a photoresistor through which a control voltage is fed to a light intensity controlling device through which a second portion of the laser beam passes. Light attenuation means are provided to vary the intensity of the laser light used to control the resistance of the photodetector. An optical delay path is provided through which the second portion of the beam travels before reaching the light intensity controlling device. The control voltage is supplied by a variable power supply. The apparatus may be tuned to properly attenuate the laser beam passing through the intensity controlling device by adjusting the power supply, the optical delay path, or the light attenuating means.

  5. Effect of using GPS autosteer guidance systems on the eye-glance behavior and posture of tractor operators.

    PubMed

    Karimi, D; Henry, J; Mann, D D

    2012-10-01

    Tractor operators are prone to neck and back discomfort and disorders. It is well known that awkward posture is a major contributor to this problem. Previous studies have investigated the prevalence of awkward posture and the resulting discomfort and disorders among tractor operators. They have also suggested various ways to mitigate this problem. With the introduction of new autosteer guidance systems, the tractor operator is relieved from the task of steering the tractor for most of the time during field work. Therefore, it is expected that the operator's posture will change. The goal of this study was to investigate the changes in the eye-glance behavior and posture of tractor operators as a result of using autosteer guidance systems. An eye-tracking system and a camcorder were used to record the eye-glance behavior and posture of 13 tractor operators as they performed seeding operations. The experiment with each operator consisted of two sessions. In one session, the operator used an autosteer system, while in the other session the operator steered the tractor manually. Analysis of the data showed that the eye-glance behavior and posture of the operators were significantly different between the autosteer and manual steering sessions. With the autosteer system, the operators spent less time in an awkward posture, and they changed their posture less frequently. However, even with the autosteer system, the operators spent 1/3 of their time in an awkward posture. Subjective feedback from the operators indicated that more than half of them experienced back or neck/shoulder discomfort during or after seeding. It is essential that the recommendations of the previous studies, such as using large rear-view mirrors or a rotating tractor seat, be evaluated when the operator is using an autosteer system. Other tools, such as video cameras that show the attached equipment, should also be tested to evaluate their effectiveness in reducing the operator's exposure to awkward

  6. a Decade of Improvement in Whole-Body Vibration and Low Back Pain for Freight Container Tractor Drivers

    NASA Astrophysics Data System (ADS)

    Nishiyama, K.; Taoda, K.; Kitahara, T.

    1998-08-01

    The authors' study in 1983 revealed that the whole-body vibration of the tractor units of freight containers was most hazardous in the back-to-chest directions (x-axis). The allowable exposure time was considerably shorter than that for heavy duty trucks. The low back pain (LBP) among the drivers seemed to be due to the long working hours and the ergonomically unsound tractor design, as well as the vibration. A preventative measure was the introduction of a tractor cab suspended by an air spring instead of a steel spring. In 1992, a follow-up field study was conducted. A personal vibration exposure meter developed by us measured the whole-body vibration on eight tractors. Eighty-nine triplets matched with the age and the years of driving tractors answered a questionnaire evaluation of the ergonomics of their tractor units.The comparison of the newest steel suspension vehicles to the old ones produced by the same motor company revealed that in thex-axis the vibration level had decreased by as much as 4 to 9 dB. Some tractors showed an increase in vibration in the buttocks-to-head direction (z-axis). However, such adverse changes seemed not to affect evaluations according to the fatigue-decreased proficiency boundary (FDP) and the exposure limit (EL) recommended in ISO 2631-1978. The present models, regardless of the type of suspension, changed the direction of the most hazardous vibration from thex-axis to thez-axis. However, the effect of the air-suspension was not so remarkable as expected. Among 40% of drivers seemed to exceed the FDP boundary during a day.The questionnaire study showed an improvement in the ergonomic evaluation of the tractors. The air suspension models seemed to induce less LBP than the steel suspension models.

  7. Effect of using GPS autosteer guidance systems on the eye-glance behavior and posture of tractor operators.

    PubMed

    Karimi, D; Henry, J; Mann, D D

    2012-10-01

    Tractor operators are prone to neck and back discomfort and disorders. It is well known that awkward posture is a major contributor to this problem. Previous studies have investigated the prevalence of awkward posture and the resulting discomfort and disorders among tractor operators. They have also suggested various ways to mitigate this problem. With the introduction of new autosteer guidance systems, the tractor operator is relieved from the task of steering the tractor for most of the time during field work. Therefore, it is expected that the operator's posture will change. The goal of this study was to investigate the changes in the eye-glance behavior and posture of tractor operators as a result of using autosteer guidance systems. An eye-tracking system and a camcorder were used to record the eye-glance behavior and posture of 13 tractor operators as they performed seeding operations. The experiment with each operator consisted of two sessions. In one session, the operator used an autosteer system, while in the other session the operator steered the tractor manually. Analysis of the data showed that the eye-glance behavior and posture of the operators were significantly different between the autosteer and manual steering sessions. With the autosteer system, the operators spent less time in an awkward posture, and they changed their posture less frequently. However, even with the autosteer system, the operators spent 1/3 of their time in an awkward posture. Subjective feedback from the operators indicated that more than half of them experienced back or neck/shoulder discomfort during or after seeding. It is essential that the recommendations of the previous studies, such as using large rear-view mirrors or a rotating tractor seat, be evaluated when the operator is using an autosteer system. Other tools, such as video cameras that show the attached equipment, should also be tested to evaluate their effectiveness in reducing the operator's exposure to awkward

  8. Wind-drag estimation in a traffic accident involving a motor scooter and a tractor-trailer.

    PubMed

    Park, Chan-Seong; Jeon, Seung-Won; Lee, Kyu-Jung; Kim, Jun-Suk; Oh, Jae-Geun; Park, Jong-Chan; Lee, Hong-Seok; Choi, Young-Shik

    2012-07-01

    This case report describes a noncontact traffic accident involving a motor scooter and a tractor-trailer with a focus on the wind-drag effect. We used load cells to measure the drag force acting on a substantially similar motor scooter when a substantially similar tractor-trailer passes by it, taking into consideration various speeds of the tractor-trailer and distances between the two vehicles. A three-dimensional steady-state flow analysis was also performed by using the CFX program for computational fluid dynamics to examine the streamlines and the pressure distribution around the tractor-trailer at various speeds. From the experiment, for a separation distance of 1.0 m (3.28 ft) and a speed of 90 km/h (55.9 mph), the maximum resultant drag force is 124.5 N (28 lb); this constitutes a degree of force that could abruptly disrupt the stability in maneuvering by an operator who is unaware of the approaching tractor-trailer. In addition, a single equation that relates the tractor-trailer speed to the drag force that acts on the motor scooter was derived on the basis of the Reynolds number (Re) and the wind-drag coefficient (C(d)): C(d) = 1.298 × 10(-7) Re.

  9. Quality and accuracy of cone beam computed tomography gated by active breathing control

    SciTech Connect

    Thompson, Bria P.; Hugo, Geoffrey D.

    2008-12-15

    The purpose of this study was to evaluate the quality and accuracy of cone beam computed tomography (CBCT) gated by active breathing control (ABC), which may be useful for image guidance in the presence of respiration. Comparisons were made between conventional ABC-CBCT (stop and go), fast ABC-CBCT (a method to speed up the acquisition by slowing the gantry instead of stopping during free breathing), and free breathing respiration correlated CBCT. Image quality was assessed in phantom. Accuracy of reconstructed voxel intensity, uniformity, and root mean square error were evaluated. Registration accuracy (bony and soft tissue) was quantified with both an anthropomorphic and a quality assurance phantom. Gantry angle accuracy was measured with respect to gantry speed modulation. Conventional ABC-CBCT scan time ranged from 2.3 to 5.8 min. Fast ABC-CBCT scan time ranged from 1.4 to 1.8 min, and respiratory correlated CBCT scans took 2.1 min to complete. Voxel intensity value for ABC gated scans was accurate relative to a normal clinical scan with all projections. Uniformity and root mean square error performance degraded as the number of projections used in the reconstruction of the fast ABC-CBCT scans decreased (shortest breath hold, longest free breathing segment). Registration accuracy for small, large, and rotational corrections was within 1 mm and 1 degree sign . Gantry angle accuracy was within 1 degree sign for all scans. For high-contrast targets, performance for image-guidance purposes was similar for fast and conventional ABC-CBCT scans and respiration correlated CBCT.

  10. Fusion studies with low-intensity radioactive ion beams using an active-target time projection chamber

    NASA Astrophysics Data System (ADS)

    Kolata, J. J.; Howard, A. M.; Mittig, W.; Ahn, T.; Bazin, D.; Becchetti, F. D.; Beceiro-Novo, S.; Chajecki, Z.; Febbrarro, M.; Fritsch, A.; Lynch, W. G.; Roberts, A.; Shore, A.; Torres-Isea, R. O.

    2016-09-01

    The total fusion excitation function for 10Be+40Ar has been measured over the center-of-momentum (c.m.) energy range from 12 to 24 MeV using a time-projection chamber (TPC). The main purpose of this experiment, which was carried out in a single run of duration 90 h using a ≈100 particle per second (pps) 10Be beam, was to demonstrate the capability of an active-target TPC to determine fusion excitation functions for extremely weak radioactive ion beams. Cross sections as low as 12 mb were measured with acceptable (50%) statistical accuracy. It also proved to be possible to separate events in which charged particles were emitted from the fusion residue from those in which only neutrons were evaporated. The method permits simultaneous measurement of incomplete fusion, break-up, scattering, and transfer reactions, and therefore fully exploits the opportunities presented by the very exotic beams that will be available from the new generation of radioactive beam facilities.

  11. Pulsed and monoenergetic beams for neutron cross-section measurements using activation and scattering techniques at Triangle Universities Nuclear Laboratory

    NASA Astrophysics Data System (ADS)

    Hutcheson, A.; Angell, C. T.; Becker, J. A.; Boswell, M.; Crowell, A. S.; Dashdorj, D.; Fallin, B.; Fotiades, N.; Howell, C. R.; Karwowski, H. J.; Kelley, J. H.; Kiser, M.; Macri, R. A.; Nelson, R. O.; Pedroni, R. S.; Tonchev, A. P.; Tornow, W.; Vieira, D. J.; Weisel, G. J.; Wilhelmy, J. B.

    2007-08-01

    In support of the Stewardship Science Academic Alliances initiative, an experimental program has been developed at Triangle Universities Nuclear Laboratory (TUNL) to measure (n,xn) cross-sections with both in-beam and activation techniques with the goal of improving the partial cross-section database for the NNSA Stockpile Stewardship Program. First experimental efforts include excitation function measurements on 235,238U and 241Am using pulsed and monoenergetic neutron beams with En = 5-15 MeV. Neutron-induced partial cross-sections were measured by detecting prompt γ rays from the residual nuclei using various combinations of clover and planar HPGe detectors in the TUNL shielded neutron source area. Complimentary activation measurements using DC neutron beams have also been performed in open geometry in our second target area. The neutron-induced activities were measured in the TUNL low-background counting area. In this presentation, we include detailed information about the irradiation procedures and facilities and preliminary data on first measurements using this capability.

  12. Quantifying driver's field-of-view in tractors: methodology and case study.

    PubMed

    Gilad, Issachar; Byran, Eyal

    2015-01-01

    When driving a car, the visual awareness is important for operating and controlling the vehicle. When operating a tractor, it is even more complex. This is because the driving is always accompanied with another task (e.g., plough) that demands constant changes of body postures, to achieve the needed Field-of-View (FoV). Therefore, the cockpit must be well designed to provide best FoV. Today, the driver's FoV is analyzed mostly by computer simulations of a cockpit model and a Digital Human Model (DHM) positioned inside. The outcome is an 'Eye view' that displays what the DHM 'sees'. This paper suggests a new approach that adds quantitative information to the current display; presented on three tractor models as case studies. Based on the results, the design can be modified. This may assist the engineer, to analyze, compare and improve the design, for better addressing the driver needs. PMID:26327259

  13. Co-Simulation Research of the Mechanical-Hydraulic-Control Coupling System of ITER Tractor

    NASA Astrophysics Data System (ADS)

    Yang, Xiuqing; Luo, Minzhou; Mei, Tao; Yao, Damao

    2009-06-01

    The virtual prototyping models of the mechanical, hydraulic and control system of the ITER tractor were built with CATIA, ADAMS and MATLAB/Simulink respectively according to its heavy load and high precision characteristics, and the data transfer between the different models was accomplished by the integration interface between different software. Consequently the virtual experimental platform for the multi-disciplinary co-simulation was established. A co-simulation study of the mechanical-hydraulic-control coupling system of the ITER tractor was carried out. The synchronization servo control of parallel hydraulic cylinders was implemented, and the tracking control of the preconcerted trajectory of the hydraulic cylinders was realized on the established experimental platform. This paper presents the optimization design and technology rebuilding for the complicated coupling system with its theoretic foundation and co-simulation virtual experimental platform.

  14. Heat-treatment by using induction heating on the Minsk Tractor Plant

    SciTech Connect

    Kosmovich, L.S.; Baranov, V.S.; Koshelenkov, K.N.; Fel'dman, L.Ya.

    1988-01-01

    The Minsk Tractor Plant uses a technique for hardening preceded by induction heating for more than 50% of its heat-treated parts made from 45, 40Kh, 38KhGs, and 33KhS steels. The majority of parts undergo heat-treatment on the machining lines. This method made it possible to develop and put into service an automatic device for strainless hardening of strips in the forced conditions. Improving and introducing this new technological process, equipment, and fittings for heat treatment by induction heating was found to increase the life of the tractor parts, reduce labor costs for their manufacture as well as increase savings in electricity and rolled materials.

  15. A compact neutron beam generator system designed for prompt gamma nuclear activation analysis.

    PubMed

    Ghassoun, J; Mostacci, D

    2011-08-01

    In this work a compact system was designed for bulk sample analysis using the technique of PGNAA. The system consists of (252)Cf fission neutron source, a moderator/reflector/filter assembly, and a suitable enclosure to delimit the resulting neutron beam. The moderator/reflector/filter arrangement has been optimised to maximise the thermal neutron component useful for samples analysis with a suitably low level of beam contamination. The neutron beam delivered by this compact system is used to irradiate the sample and the prompt gamma rays produced by neutron reactions within the sample elements are detected by appropriate gamma rays detector. Neutron and gamma rays transport calculations have been performed using the Monte Carlo N-Particle transport code (MCNP5).

  16. Tractor tire aspect ratio effects on soil bulk density and cone index

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A 580/70R38 tractor drive tire with an aspect ratio of 0.756 and a 650/75R32 tire with an aspect ratio of 0.804 were operated at two dynamic loads and two inflation pressures on a sandy loam and a clay loam with loose soil above a hardpan. Soil bulk density and cone index were measured just above t...

  17. Coca-Cola Refreshments Class 8 Diesel Electric Hybrid Tractor Evaluation: 13-Month Final Report

    SciTech Connect

    Walkowicz, K.; Lammert, M.; Curran, P.

    2012-08-01

    This 13-month evaluation used five Kenworth T370 hybrid tractors and five Freightliner M2106 standard diesel tractors at a Coca Cola Refreshments facility in Miami, Florida. The primary objective was to evaluate the fuel economy, emissions, and operational field performance of hybrid electric vehicles when compared to similar-use conventional diesel vehicles. A random dispatch system ensures the vehicles are used in a similar manner. GPS logging, fueling, and maintenance records and laboratory dynamometer testing are used to evaluate the performance of these hybrid tractors. Both groups drive similar duty cycles with similar kinetic intensity (0.95 vs. 0.69), average speed (20.6 vs. 24.3 mph), and stops per mile (1.9 vs. 1.5). The study demonstrated the hybrid group had a 13.7% fuel economy improvement over the diesel group. Laboratory fuel economy and field fuel economy study showed similar trends along the range of KI and stops per mile. Hybrid maintenance costs were 51% lower per mile; hybrid fuel costs per mile were 12% less than for the diesels; and hybrid vehicle total cost of operation per mile was 24% less than the cost of operation for the diesel group.

  18. Aerodynamic performance of a drag reduction device on a full-scale tractor/trailer

    NASA Astrophysics Data System (ADS)

    Lanser, Wendy R.; Ross, James C.; Kaufman, Andrew E.

    1991-09-01

    The effectiveness of an aerodynamic boattail on a tractor/trailer road vehicle was measured in the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Results are examined for the tractor/trailer with and without the drag reduction device. Pressure measurements and flow visualization show that the aerodynamic boattail traps a vortex or eddy in the corner formed between the device and the rear corner of the trailer. This recirculating flow turns the flow inward as it separates from the edges of the base of the trailer. This modified flow behavior increases the pressure acting over the base area of the truck, thereby reducing the net aerodynamic drag of the vehicle. Drag measurements and pressure distributions in the region of the boattail device are presented for selected configurations. The optimum configuration reduces the overall drag of the tractor/trailer combination by about 10 percent at a zero yaw angle. Unsteady pressure measurements do not indicate strong vortex shedding, although the addition of the boattail plates increases high frequency content of the fluctuating pressure.

  19. Aerodynamic performance of a drag reduction device on a full-scale tractor/trailer

    NASA Technical Reports Server (NTRS)

    Lanser, Wendy R.; Ross, James C.; Kaufman, Andrew E.

    1991-01-01

    The effectiveness of an aerodynamic boattail on a tractor/trailer road vehicle was measured in the NASA Ames Research Center 80- by 120-Foot Wind Tunnel. Results are examined for the tractor/trailer with and without the drag reduction device. Pressure measurements and flow visualization show that the aerodynamic boattail traps a vortex or eddy in the corner formed between the device and the rear corner of the trailer. This recirculating flow turns the flow inward as it separates from the edges of the base of the trailer. This modified flow behavior increases the pressure acting over the base area of the truck, thereby reducing the net aerodynamic drag of the vehicle. Drag measurements and pressure distributions in the region of the boattail device are presented for selected configurations. The optimum configuration reduces the overall drag of the tractor/trailer combination by about 10 percent at a zero yaw angle. Unsteady pressure measurements do not indicate strong vortex shedding, although the addition of the boattail plates increases high frequency content of the fluctuating pressure.

  20. Active retroreflector with in situ beam analysis to measure the rotational orientation in conjunction with a laser tracker

    NASA Astrophysics Data System (ADS)

    Hofherr, O.; Wachten, C.; Müller, C.; Reinecke, H.

    2013-04-01

    High precision optical non-contact position measurement is a key technology in modern engineering. Laser trackers (LT) can determine accurately x-y-z coordinates of passive retroreflectors. Next-generation systems answer the additional need to measure an object`s rotational orientation (pitch, yaw, roll). These devices are based either on photogrammetry or on enhanced retroreflectors. However, photogrammetry relies on costly camera systems and time-consuming image processing. Enhanced retroreflectors analyze the LT`s beam but are restricted in roll angle measurements. In the past we have presented a new method [1][2] to measure all six degrees of freedom in conjunction with a LT. Now we dramatically optimized the method and designed a new prototype, e.g. taking into consideration optical alignment, reduced power loss, highly optimized measuring signals and higher resolution. A method is described that allows compensating the influence of the LT's beam offset during tracking the active retroreflector. We prove the functionality of the active retroreflector with the LT and, furthermore, demonstrate the capability of the system to characterize the tracking behavior of a LT. The measurement range for the incident laser beam is +/-12° with a resolution of 0.6".

  1. The Prototype Active-Target Time-Projection Chamber used with TwinSol radioactive-ion beams

    NASA Astrophysics Data System (ADS)

    Ahn, T.; Bardayan, D. W.; Bazin, D.; Beceiro Novo, S.; Becchetti, F. D.; Bradt, J.; Brodeur, M.; Carpenter, L.; Chajecki, Z.; Cortesi, M.; Fritsch, A.; Hall, M. R.; Hall, O.; Jensen, L.; Kolata, J. J.; Lynch, W.; Mittig, W.; O'Malley, P.; Suzuki, D.

    2016-06-01

    The study of low-energy reactions with radioactive-ion beams has been greatly enhanced by the recent use of active-target detectors, which have high efficiency and low thresholds to detect low-energy charged-particle decays. Both of these features have been used in experiments with the Prototype Active-Target Time-Projection Chamber to study α -cluster structure in unstable nuclei and 3-body charged-particle decays after implantation. Predicted α -cluster structures in 14 C were probed using resonant α scattering and the nature of the 3- α breakup of the 02+ Hoyle state in 12 C after the beta decay of 12 N and 12 B was studied. These experiments used in-flight radioactive-ion beams that were produced using the dual superconducting solenoid magnets TwinSol at the University of Notre Dame. Preliminary results from these experiments as well as the development of future radioactive beams to be used in conjunction with the PAT-TPC are presented.

  2. Crossed Molecular Beam Studies and Dynamics of Decomposition of Chemically Activated Radicals

    DOE R&D Accomplishments Database

    Lee, Y. T.

    1973-09-01

    The power of the crossed molecular beams method in the investigation of the dynamics of chemical reactions lies mainly in the direct observation of the consequences of single collisions of well controlled reactant molecules. The primary experimental observations which provide information on reaction dynamics are the measurements of angular and velocity distributions of reaction products.

  3. Modeling energy transport in a cantilevered Euler-Bernoulli beam actively vibrating in Newtonian fluid

    NASA Astrophysics Data System (ADS)

    Faria, Cassio T.; Inman, Daniel J.

    2014-04-01

    When a mechanical and/or structural component is immersed in a fluid and it vibrates, the reasonable assumption is that part of the energy is transmitted to the adjacent media. For some engineering applications the energy transport between these two domains, i.e., structure and fluid, plays a central role. The work presented in this paper is focused on discussing the energy transport in beam-like structures as they can be used to represent flexible swimmers (fish-like pulsating mechanisms) in their simplest form. In order to expose the role of each of the fluid and beam properties effecting the energy transfer process, a simplified analytical fluid-structure interaction (FSI) model is derived. After analysis of the resulting coupled-systems' damping coefficient, a new energy transport component is added to the initial Euler-Bernoulli beam equation; a term associated with diffusion (fluid viscosity). In addition our modeling results in an added mass term, a characteristic consistent with previous literature. While deriving the model, an important assumption is made: beam mode shapes are not significantly affected by the domains' interaction. This hypothesis is experimentally tested in two different fluid media and confirmed to be reasonable for the first three vibration mode shapes.

  4. Pulsed supersonic molecular beam for characterization of chemically active metal-organic complexes at surfaces

    NASA Astrophysics Data System (ADS)

    Lear, Amanda M.

    Metal-organic coordination networks (MOCNs) at surfaces consist of a complex of organic ligands bound to an atomic metal center. The MOCNs, when chosen appropriately, can form highly-ordered arrays at surfaces. Ultra-high vacuum surface studies allow control of surface composition and provide 2D growth restrictions, which lead to under-coordinated metal centers. These systems provide an opportunity to tailor the chemical function of the metal centers due to the steric restrictions imposed by the surface. Tuning the adsorption/desorption energy at a metal center and developing a cooperative environment for catalysis are the key scientific questions that motivate the construction of a molecular beam surface analysis system. Characterization of the created systems can be performed utilizing a pulsed supersonic molecular beam (PSMB) in unison with a quadrupole mass spectrometer. A PSMB allows for the highly controlled delivery of reactants with well-defined energy to a given platform making it possible to elucidate detailed chemical tuning information. In this thesis, a summary of prior theoretical molecular beam derivations is provided. Design considerations and an overview of the construction procedure for the current molecular beam apparatus, including initial characterization experiments, are presented. By impinging an Ar beam on a Ag(111) surface, the location of the specular angle (˜65°) and rough sample perimeter coordinates were determined. Additionally, surface analysis experiments, mainly Auger Electron Spectroscopy (AES), were performed to investigate the oxidation of epitaxial graphene on the SiC(0001) surface utilizing an oxygen cracking method. The AES experiments are described in detail and highlight the challenges that were faced when several different graphene samples were used for the oxygen adsorption/desorption experiments.

  5. Active Position Control of a Flexible Smart Beam Using Internal Model Control

    NASA Astrophysics Data System (ADS)

    LEE, Y.-S.; ELLIOTT, S. J.

    2001-05-01

    The problem of controlling the position at the tip of a flexible cantilever beam to follow a command signal is considered, by using a pair of piezoelectric actuators at the clamped end. The beam is lightly damped and so the natural transient response is rather long, and also since the sensor and actuator are not collocated, the plant response is non-minimum phase. Two control strategies were investigated. The first involved conventional PID control in which the feedback gains were adjusted to give the fastest closed-loop response to a step input. The second control strategy was based on an internal model control (IMC) architecture. The control filter in the IMC controller was a digital FIR device designed to minimize the expectation of the mean square tracking error. In practice, such smart beams could be exposed to temperature fluctuations and changes in geometry. The effect of these variations on the stability was studied and it is shown that the need for robustness to such variations leads to a limitation in the performance of an IMC controller. The improvement in the stability robustness by incorporating control effort weighting into the cost function being minimized was investigated, as was the incorporation of modelling delay in the design of the IMC control filter. The IMC controller designed for the beam was found to have much reduced settling times to a step input compared with those of the PID controller while maintaining good robustness to changes in temperature. However, the extremely low damping of the experimental beam made it difficult to implement an accurate plant model in practice.

  6. Beam-Beam Interactions

    SciTech Connect

    Sramek, Christopher

    2003-09-05

    At the interaction point of a particle accelerator, various phenomena occur which are known as beam-beam effects. Incident bunches of electrons (or positrons) experience strong electromagnetic fields from the opposing bunches, which leads to electron deflection, beamstrahlung and the creation of electron/positron pairs and hadrons due to two-photon exchange. In addition, the beams experience a ''pinch effect'' which focuses each beam and results in either a reduction or expansion of their vertical size. Finally, if a beam's disruption parameter is too large, the beam can develop a sinusoidal distortion, or two-stream (kink) instability. This project simulated and studied these effects as they relate to luminosity, deflection angles and energy loss in order to optimize beam parameters for the Next Linear Collider (NLC). Using the simulation program Guinea-Pig, luminosity, deflection angle and beam energy data was acquired for different levels of beam offset and distortion. Standard deflection curves and luminosity plots agreed with theoretical models but also made clear the difficulties of e-e- feedback. Simulations emphasizing kink instability in modulated and straight beam collisions followed qualitative behavioral predictions and roughly fit recent analytic calculations. Finally, a study of e-e- collisions under design constraints for the NLC provided new estimates of how luminosity, beamstrahlung energy loss, upsilon parameter and deflection curve width scale with beam spotsizes.

  7. Active space debris charging for contactless electrostatic disposal maneuvers

    NASA Astrophysics Data System (ADS)

    Schaub, Hanspeter; Sternovsky, Zoltán

    2014-01-01

    The remote charging of a passive object using an electron beam enables touchless re-orbiting of large space debris from geosynchronous orbit (GEO) using electrostatic forces. The advantage of this method is that it can operate with a separation distance of multiple craft radii, thus reducing the risk of collision. The charging of the tug-debris system to high potentials is achieved by active charge transfer using a directed electron beam. Optimal potential distributions using isolated- and coupled-sphere models are discussed. A simple charging model takes into account the primary electron beam current, ultra-violet radiation induced photoelectron emission, collection of plasma particles, secondary electron emission and the recapture of emitted particles. The results show that through active charging in a GEO space environment high potentials can be both achieved and maintained with about a 75% transfer efficiency. Further, the maximum electrostatic tractor force is shown to be insensitive to beam current levels. This latter later result is important when considering debris with unknown properties.

  8. Proton beam simulation with MCNPX/CINDER'90: Germanium metal activation estimates below 30MeV relevant to the bulk production of arsenic radioisotopes.

    PubMed

    Fassbender, M; Taylor, W; Vieira, D; Nortier, M; Bach, H; John, K

    2012-01-01

    Germanium metal targets encapsulated in Nb shells were irradiated in a proton beam. Proton and secondary neutron beam fluences as well as radionuclide activity formation were modeled using MCNPX in combination with CINDER90. Targets were chemically processed using distillation and anion exchange. Good agreement between the measured radiochemical yields and MCNPX/CINDER90 estimates was observed. A target of pentavalent (73,74)As radioarsenic for neutron activation studies was prepared.

  9. Proton beam simulation with MCNPX/CINDER'90: Germanium metal activation estimates below 30MeV relevant to the bulk production of arsenic radioisotopes.

    PubMed

    Fassbender, M; Taylor, W; Vieira, D; Nortier, M; Bach, H; John, K

    2012-01-01

    Germanium metal targets encapsulated in Nb shells were irradiated in a proton beam. Proton and secondary neutron beam fluences as well as radionuclide activity formation were modeled using MCNPX in combination with CINDER90. Targets were chemically processed using distillation and anion exchange. Good agreement between the measured radiochemical yields and MCNPX/CINDER90 estimates was observed. A target of pentavalent (73,74)As radioarsenic for neutron activation studies was prepared. PMID:21890369

  10. BEAM-BEAM 2003 SUMMARY.

    SciTech Connect

    FISCHER,W.SEN,T.

    2003-05-19

    This paper summarizes the presentations and discussions of the Beam-Beam'03 workshop, held in Montauk, Long Island, from May 19 to 23, 2003. Presentations and discussions focused on halo generation from beam-beam interactions; beam-beam limits, especially coherent limits and their effects on existing and future hadron colliders; beam-beam compensation techniques, particularly for long-range interactions; and beam-beam study tools in theory, simulation, and experiment.

  11. Range degradation and distal edge behavior of proton radiotherapy beams using 11C activation and Monte Carlo simulation

    NASA Astrophysics Data System (ADS)

    Elmekawy, Ahmed Farouk

    The distal edge of therapeutic proton radiation beams was investigated by different methods. Proton beams produced at the Hampton University Proton Therapy Institute (HUPTI) were used to irradiate a Polymethylmethacrylate (PMMA) phantom for three different ranges (13.5, 17.0 and 21.0 cm) to investigate the distal slope dependence of the Bragg peak. The activation of 11 C was studied by scanning the phantom less than 10 minutes post-irradiation with a Philips Big Bore Gemini(c) PET/CT. The DICOM images were imported into the Varian Eclipse(c) Treatment Planning System (TPS) for analysis and then analyzed by ImageJ(c) . The distal slope ranged from ?0.1671 +/- 0.0036 to -0.1986 +/- 0.0052 (pixel intensity/slice number) for ranges 13.5 to 21.0 cm respectively. A realistic description of the setup was modeled using the GATE 7.0 Monte Carlo simulation tool and compared to the experiment data. The results show the distal slope ranged from -0.1158+/-0.0133 to -0.0787+/-0.002 (Gy/mm). Additionally, low activity, 11C were simulated to study the 11C reconstructed half-life dependence versus the initial activity for six ranges chosen around the previous activation study. The results of the expected/nominal half-life vs. activity ranged from -5 x 10-4 +/- 2.8104 x 10-4 to 1.6 x 10-3 +/- 9.44 x 10-4 (%diff./Bq). The comparison between two experiments with proton beams on a PMMA phantom and multi-layer ion chamber, and two GATE simulations of a proton beam incident on a water phantom and 11C PET study show that: (i) the distal fall-off variation of the steepness of the slopes are found to be similar thus validating the sensitivity of the PET technique to the range degradation and (ii) the average of the super-ratios difference between all studies observed is primarily due to the difference in the dose deposited in the media.

  12. The flow in the gap of a tractor-trailer in the presence of a side wind

    NASA Astrophysics Data System (ADS)

    Hammache, Mustapha; Browand, Fred

    2000-11-01

    The aerodynamic performance of large trucks is greatly influenced by the gap between tractor and trailer and by the presence of a side wind. The present work examines these effects by using a baseline geometry consisting of a 1/15th scale model of an integrated tractor-trailer truck called the Ground Transportation System (GTS). The experiments are conducted in a wind tunnel at a free-stream velocity of 20 m/s, which corresponds to a Reynolds number of approximately 260,000 based on the square-root of the truck’s frontal area. The tractor-trailer is yawed at various angles with respect to the free-stream and the drag and side forces on the tractor and the trailer are measured (separately) as a function of gap spacing and yaw angle. The flow in the gap region is measured with the particle image velocimetry (PIV) technique. The data shows that the lowest drag is achieved at zero gap and no side wind. At small but finite yaw angles, there exists a critical gap spacing at which the flow undergoes a transition that causes a sharp rise in the drag on both tractor and trailer. Different flow states can be established and significant hysteresis effects are observed as the critical gap is approached from higher versus lower values of the gap spacing.

  13. Runaway electron generation as possible trigger for enhancement of magnetohydrodynamic plasma activity and fast changes in runaway beam behavior

    SciTech Connect

    Pankratov, I. M. E-mail: rjzhou@ipp.ac.cn; Zhou, R. J. E-mail: rjzhou@ipp.ac.cn; Hu, L. Q.

    2015-07-15

    Peculiar phenomena were observed during experiments with runaway electrons: rapid changes in the synchrotron spot and its intensity that coincided with stepwise increases in the electron cyclotron emission (ECE) signal (cyclotron radiation of suprathermal electrons). These phenomena were initially observed in TEXTOR (Tokamak Experiment for Technology Oriented Research), where these events only occurred in the current decay phase or in discharges with thin stable runaway beams at a q = 1 drift surface. These rapid changes in the synchrotron spot were interpreted by the TEXTOR team as a fast pitch angle scattering event. Recently, similar rapid changes in the synchrotron spot and its intensity that coincided with stepwise increases in the non-thermal ECE signal were observed in the EAST (Experimental Advanced Superconducting Tokamak) runaway discharge. Runaway electrons were located around the q = 2 rational magnetic surface (ring-like runaway electron beam). During the EAST runaway discharge, stepwise ECE signal increases coincided with enhanced magnetohydrodynamic (MHD) activity. This behavior was peculiar to this shot. In this paper, we show that these non-thermal ECE step-like jumps were related to the abrupt growth of suprathermal electrons induced by bursting electric fields at reconnection events during this MHD plasma activity. Enhancement of the secondary runaway electron generation also occurred simultaneously. Local changes in the current-density gradient appeared because of local enhancement of the runaway electron generation process. These current-density gradient changes are considered to be a possible trigger for enhancement of the MHD plasma activity and the rapid changes in runaway beam behavior.

  14. Electronically controlled optical beam-steering by an active phased array of metallic nanoantennas.

    PubMed

    DeRose, C T; Kekatpure, R D; Trotter, D C; Starbuck, A; Wendt, J R; Yaacobi, A; Watts, M R; Chettiar, U; Engheta, N; Davids, P S

    2013-02-25

    An optical phased array of nanoantenna fabricated in a CMOS compatible silicon photonics process is presented. The optical phased array is fed by low loss silicon waveguides with integrated ohmic thermo-optic phase shifters capable of 2π phase shift with ∼ 15 mW of applied electrical power. By controlling the electrical power to the individual integrated phase shifters fixed wavelength steering of the beam emitted normal to the surface of the wafer of 8° is demonstrated for 1 × 8 phased arrays with periods of both 6 and 9 μm. PMID:23482053

  15. Effect of chlorine activation treatment on electron beam induced current signal distribution of cadmium telluride thin film solar cells

    NASA Astrophysics Data System (ADS)

    Zywitzki, Olaf; Modes, Thomas; Morgner, Henry; Metzner, Christoph; Siepchen, Bastian; Späth, Bettina; Drost, Christian; Krishnakumar, Velappan; Frauenstein, Sven

    2013-10-01

    We have investigated CdTe thin film solar cells without activation treatment and with CdCl2 activation treatment at temperatures between 370 and 430 °C using a constant activation time of 25 min. For this purpose, CdS/CdTe layers were deposited by closed-space-sublimation on FTO coated float glass. The solar cells were characterized by measurements of the JV characteristics and quantum efficiencies. In addition, ion polished cross sections of the solar cells were prepared for high-resolution FE-SEM imaging of the microstructure and the simultaneous registration of electron beam induced current (EBIC) signal distribution. By measurement of the EBIC signal distribution, it can be shown that without activation treatment the CdTe grain boundaries itself and grain boundary near regions exhibit no EBIC signal, whereas centres of some singular grains already show a distinct EBIC signal. In contrast, after the chlorine activation treatment, the grain boundary near regions exhibit a significant higher EBIC signal than the centre of the grains. The results can be discussed as a direct evidence for defect passivation of grain boundary near regions by the chlorine activation treatment. At activation temperature of 430 °C, additionally, a significant grain growth and agglomeration of the CdS layer can be recognized, which is linked with the formation of voids within the CdS layer and a deterioration of pn junction properties.

  16. Estimating car driver injury severity in car/tractor-trailer collisions.

    PubMed

    Shao, S P

    1987-06-01

    This paper analyzes road accidents between passenger cars and tractor-trailer rigs occurring in the greater Baltimore-Washington D.C. metropolitan area during the period 1983-84. During this time interval, approximately 1700 such collisions occurred on major highways in the state of Maryland. Traffic accident data is factor analyzed for underlying dimensions related to this accident type. A subsequent prediction analysis is made in order to discern whether injury severity estimations can be made using driver, vehicle, and environmental characteristic variables.

  17. Determination of influence factors and accident rates for the Armored Tractor/Safe Secure Trailer

    SciTech Connect

    Phillips, J.S.; Clauss, D.B.; Blower, D.F.

    1994-04-01

    Operating environments, such as road type, road location, and time of day, play an important role in the observed accident rates of heavy trucks used in general commerce. These same factors influence the accident rate of the Armored Tractor/Safe Secure Trailer (AT/SST) used by the Department of Energy to transport hazardous cargos within the continental United States. This report discusses the development of accident rate influence factors. These factors, based on heavy trucks used in general commerce, are used to modify the observed overall AT/SST accident rate to account for the different operating environments.

  18. The analysis of work-related injuries in a tractor factory.

    PubMed

    Nikoli, N; Mavrić, T

    1994-05-01

    An analysis of work-related injuries and absenteeism was carried out in a steel production and tractor manufacturing factory from 1982 to 1986. During that period there were 1152 injuries and 16,798 working days lost. Foundry workers were the most frequently injured; fists and fingers were the most frequently affected parts of the body. The number of injuries at work as well as the number of lost working days were highly influenced by the low socio-economic position of workers and by a general recession.

  19. Structural dynamics modeling and testing of the Department of Energy tractor/trailer combination

    SciTech Connect

    Field, R.V. Jr.; Hurtado, J.E.; Carne, T.G.; Dohrmann, C.R.

    1996-12-31

    This study presents a combined analytical and experimental effort to characterize and improve the ride quality of the Department of Energy tractor/trailer combination. The focus is to augment the experimental test results with the use of a high quality computer model. The discussion includes an overview of the finite element model of the vehicle and experimental modal test results. System identification techniques are employed to update the mathematical model. The validated model is then used to illustrate the benefits of incorporating two major design changes, namely the switch from a separate cab/sleeper configuration to an integrated cab, and the use of a cab suspension system.

  20. Defect study in molecular beam epitaxy-grown HgCdTe films with activated and unactivated arsenic

    SciTech Connect

    Izhnin, I. I.; Dvoretsky, S. A.; Mikhailov, N. N.; Varavin, V. S.; Mynbaev, K. D.; Fitsych, O. I.; Pociask-Bialy, M.; Sheregii, E.; Voitsekhovskii, A. V.

    2014-04-28

    A defect study was performed on molecular beam epitaxy-grown HgCdTe films in situ doped with arsenic. Doping was performed from either effusion cell or cracker cell, and studied were both as-grown samples and samples subjected to arsenic activation annealing. Electrical properties of the films were investigated with the use of ion milling as a means of “stirring” defects in the material. As a result of the study, it was confirmed that the most efficient incorporation of electrically active arsenic occurs at the cracking zone temperature of 700 °C. Interaction between arsenic and tellurium during the growth was observed and is discussed in the paper.

  1. Increased proapoptotic activity of electron beam irradiated doxorubicin and epirubicin in multidrug-resistant human leukemic cells.

    PubMed

    Paszel-Jaworska, A; Totoń, E; Dettlaff, K; Kaczmarek, A; Bednarski, W; Oszczapowicz, I; Jelińska, A; Rybczyńska, M

    2016-10-25

    This study evaluated the effect of electron beam irradiation on the cytotoxic activity of anthracycline antibiotics such as doxorubicin (DOX), epirubicin (EPI), and dunorubicin (DAU) in human acute lymphoblastic leukemia cell line CCRF-CEM and its multidrug-resistant variant CCRF-VCR1000 cell line characterized by the overexpression of ABCB1 gene. Drugs were irradiated at doses of 10 and 25 kGy. Data from EPR studies proved that the highest concentration of free radicals was found in DOX and that the number of stable free radicals is always greater after irradiation. In in vitro studies, a higher cytotoxic activity of irradiated DOX and EPI in multidrug-resistant CCRF-VCR1000 cells was observed. This tendency was maintained during the storage at 4 °C for 90 days. Changes in CCRF-CEM cells' viability were not dependent on the irradiation status and its dose and were only drug-concentration dependent in all measurement time points. It was proved that increased potency of 25 kGy e-beam irradiated drugs results from their enhanced proapoptotic activity. Apoptotic cell death observed in CCRF-VCR1000 cells treated with irradiated drugs was caspase-8, -9, and -3 dependent and related to the increased Bax/Bcl-2 ratio. No significant differences in the effects of irradiated and non-irradiated drugs on p53 and NFκB transcription factor level and their translocation to the nucleus were noted. Increased activity of the irradiated drugs was not dependent on ABCB1 level.

  2. Fast crystallization of amorphous Gd{sub 2}Zr{sub 2}O{sub 7} induced by thermally activated electron-beam irradiation

    SciTech Connect

    Huang, Zhangyi; Qi, Jianqi Zhou, Li; Feng, Zhao; Yu, Xiaohe; Gong, Yichao; Yang, Mao; Wei, Nian; Shi, Qiwu; Lu, Tiecheng

    2015-12-07

    We investigate the ionization and displacement effects of an electron-beam (e-beam) on amorphous Gd{sub 2}Zr{sub 2}O{sub 7} synthesized by the co-precipitation and calcination methods. The as-received amorphous specimens were irradiated under electron beams at different energies (80 keV, 120 keV, and 2 MeV) and then characterized by X-ray diffraction and transmission electron microscopy. A metastable fluorite phase was observed in nanocrystalline Gd{sub 2}Zr{sub 2}O{sub 7} and is proposed to arise from the relatively lower surface and interface energy compared with the pyrochlore phase. Fast crystallization could be induced by 120 keV e-beam irradiation (beam current = 0.47 mA/cm{sup 2}). The crystallization occurred on the nanoscale upon ionization irradiation at 400 °C after a dose of less than 10{sup 17} electrons/cm{sup 2}. Under e-beam irradiation, the activation energy for the grain growth process was approximately 10 kJ/mol, but the activation energy was 135 kJ/mol by calcination in a furnace. The thermally activated ionization process was considered the fast crystallization mechanism.

  3. Reduction of aerodynamic drag and fuel consumption for tractor-trailer vehicles

    NASA Technical Reports Server (NTRS)

    Muirhead, V. U.; Saltzman, E. J.

    1979-01-01

    Wind-tunnel tests were performed on a scale model of a cab-over-engine tractor-trailer vehicle and several modifications of the model. Results from two of the model configurations were compared with full-scale drag data obtained from similar configurations during coast-down tests. Reductions in fuel consumption derived from these tests are presented in terms of fuel quantity and dollar savings per vehicle year, based on an annual driving distance of 160,900 km (100,000 mi.). The projected savings varied from 13,001 (3435) to 25,848 (6829) liters (gallons) per year which translated to economic savings from $3435 to about $6829 per vehicle year for an operating speed of 88.5 km/h (55 mph) and wind speeds near the national average of 15.3 km/h (9.5 mph). The estimated cumulative fuel savings for the entire U.S. fleet of cab-over-engine tractor, van-type trailer combinations ranged from 4.18 million kl (26.3 million bbl) per year for a low-drag configuration to approximately twice that amount for a more advanced configuration.

  4. Development and implementation of thermal signature testing protocol of auxiliary power unit (APU) and diesel tractor

    NASA Astrophysics Data System (ADS)

    Jenkins, Chelsea L.; Bourne, Stefanie M.; Rowley, Matthew J.; Miles, Jonathan J.

    2004-04-01

    Thermal signature may be one of the defining factors in determining the applicability of fuel cell auxiliary power unit (APU) technology in military applications. Thermal characterization is important for military applications given that identification and detection may be accomplished through observation of its thermal signature. The operating modes and power takeoff operations of a vehicle will likely determine the thermal profile. The objective of our study was to develop and implement a protocol for quantifying the thermal characteristics of a methanol fuel cell and an idling tractor engine under representative characteristic operations. APU thermal characteristics are a special case for which standardized testing procedures do not presently exist. A customized testing protocol was developed and applied that is specific to an APU-equipped vehicle. Initial testing was conducted on the methanol APU-equipped Freightliner tractor using a high-performance radiometric infrared system. The APU profile calls for a series of infrared images to be collected at three different viewing angles and two different elevations under various loads. The diesel engine was studied in a similar fashion using seven different viewing angles and two different elevations. Raw data collected according to the newly developed methodology provided the opportunity for computer analysis and thermal profiling of both the fuel cell and the diesel engine.

  5. Preventing tractor rollover fatalities: performance of the NIOSH autoROPS.

    PubMed

    Powers, J R; Harris, J R; Etherton, J R; Ronaghi, M; Snyder, K A; Lutz, T J; Newbraugh, B H

    2001-09-01

    Approximately 132 agricultural tractor overturn fatalities occur per year. The use of rollover protective structures (ROPS), along with seat belts, is the best known method for preventing these fatalities. One impediment to ROPS use, however, is low clearance situations, such as orchards and animal confinement buildings. To address the need for ROPS that are easily adapted to low clearance situations, the Division of Safety Research, National Institute for Occupational Safety and Health (NIOSH), developed an automatically deploying, telescoping ROPS (Auto-ROPS). The NIOSH AutoROPS consists of two subsystems. The first is a retractable ROPS that is normally latched in its lowered position for day-to-day use. The second subsystem is a sensor that monitors the operating angle of the tractor. Ifa rollover condition is detected by the sensor, the retracted ROPS will deploy and lock in the full upright position before ground contact. Static load testing and field upset tests of the NIOSH AutoROPS have been conducted in accordance with SAE standard J2194. Additionally, timed trials of the AutoROPS deployment mechanism were completed. The design of the retractable ROPS and sensor, as well as the results of the different testing phases are discussed.

  6. Fishbone activity in experimental advanced superconducting tokamak neutral beam injection plasma

    SciTech Connect

    Xu, Liqing; Zhang, Jizong; Chen, Kaiyun E-mail: lqhu@ipp.cas.cn; Hu, Liqun E-mail: lqhu@ipp.cas.cn; Li, Erzhong; Lin, Shiyao; Shi, Tonghui; Duan, Yanmin; Zhu, Yubao

    2015-12-15

    Repetitive fishbones near the trapped ion procession frequency were observed for the first time in the neutral beam injection high confinement plasmas in Experimental Advanced Superconducting Tokamak (EAST) tokamak, and diagnosed using a solid-state neutral particle analyzer based on a compact silicon photodiode together with an upgraded high spatial-temporal-resolution multi-arrays soft X-ray (SX) system. This 1/1 typical internal kink mode propagates in the ion-diamagnetism direction with a rotation speed faster than the bulk plasma in the plasma frame. From the SX measurements, this mode frequency is typical of chirping down and the energetic particle effect related to the twisting mode structure. This ion fishbone was found able to trigger a multiple core sawtooth crashes with edge-2/1 sideband modes, as well as to lead to a transition from fishbone to long lived saturated kink mode to fishbone. Furthermore, using SX tomography, a correlation between mode amplitude and mode frequency was found. Finally, a phenomenological prey–predator model was found to reproduce the fishbone nonlinear process well.

  7. Fishbone activity in experimental advanced superconducting tokamak neutral beam injection plasma

    NASA Astrophysics Data System (ADS)

    Xu, Liqing; Zhang, Jizong; Chen, Kaiyun; Hu, Liqun; Li, Erzhong; Lin, Shiyao; Shi, Tonghui; Duan, Yanmin; Zhu, Yubao

    2015-12-01

    Repetitive fishbones near the trapped ion procession frequency were observed for the first time in the neutral beam injection high confinement plasmas in Experimental Advanced Superconducting Tokamak (EAST) tokamak, and diagnosed using a solid-state neutral particle analyzer based on a compact silicon photodiode together with an upgraded high spatial-temporal-resolution multi-arrays soft X-ray (SX) system. This 1/1 typical internal kink mode propagates in the ion-diamagnetism direction with a rotation speed faster than the bulk plasma in the plasma frame. From the SX measurements, this mode frequency is typical of chirping down and the energetic particle effect related to the twisting mode structure. This ion fishbone was found able to trigger a multiple core sawtooth crashes with edge-2/1 sideband modes, as well as to lead to a transition from fishbone to long lived saturated kink mode to fishbone. Furthermore, using SX tomography, a correlation between mode amplitude and mode frequency was found. Finally, a phenomenological prey-predator model was found to reproduce the fishbone nonlinear process well.

  8. Comparison of short-lived medical isotopes activation by laser thin target induced protons and conventional cyclotron proton beams

    NASA Astrophysics Data System (ADS)

    Murray, Joseph; Dudnikova, Galina; Liu, Tung-Chang; Papadopoulos, Dennis; Sagdeev, Roald; Su, J. J.; UMD MicroPET Team

    2014-10-01

    Production diagnostic or therapeutic nuclear medicines are either by nuclear reactors or by ion accelerators. In general, diagnostic nuclear radioisotopes have a very short half-life varying from tens of minutes for PET tracers and few hours for SPECT tracers. Thus supplies of PET and SPECT radiotracers are limited by regional production facilities. For example 18F-fluorodeoxyglucose (FDG) is the most desired tracer for positron emission tomography because its 110 minutes half-life is sufficient long for transport from production facilities to nearby users. From nuclear activation to completing image taking must be done within 4 hours. Decentralized production of diagnostic radioisotopes will be idea to make high specific activity radiotracers available to researches and clinicians. 11 C, 13 N, 15 O and 18 F can be produced in the energy range from 10-20 MeV by protons. Protons of energies up to tens of MeV generated by intense laser interacting with hydrogen containing targets have been demonstrated by many groups in the past decade. We use 2D PIC code for proton acceleration, Geant4 Monte Carlo code for nuclei activation to compare the yields and specific activities of short-lived isotopes produced by cyclotron proton beams and laser driven protons.

  9. Hybrid Control of an Euler-Bernoulli Beam Using Direct Velocity Feedback and Wave-Filter-Based Active Wave Control

    NASA Astrophysics Data System (ADS)

    Iwamoto, Hiroyuki; Tanaka, Nobuo; Hill, Simon G.

    Active wave control strategy enables the inactivation of vibration mode, which is valid for suppressing the vibration of a distributed parameter structure. However, when active wave control is applied, new vibration modes are produced in the uncontrolled region. To overcome this problem, this paper proposes a novel control strategy based on a hybrid combination of direct velocity feedback (DVFB) and active wave control. The two control methods have complementary qualities; DVFB is for improving the stability, and active wave control is for its unique control effects. First, a transfer matrix method in the Laplace domain is introduced to describe wave propagation phenomena of an Euler-Bernoulli beam. Then the wave filtering method which uses point sensors is presented. Based on the filtering method, the characteristic equation and control laws of the reflected wave absorbing control are derived. Next, the independence of the two control methods in the proposed hybrid control system is investigated by a numerical simulation. This is followed by the discussion of the stability problem of the hybrid control system via a Nyquist diagram method and three types of root loci. Finally, the control effects of the proposed control system are presented, demonstrating the validity of the proposed method.

  10. Stable transmission of slow highly charged ions through tapered glass capillary with active discharging method for sub-micron sized beams

    NASA Astrophysics Data System (ADS)

    Ikeda, Tokihiro; Kojima, Takao M.; Natsume, Yoshio; Kimura, Jun; Abe, Tomoko

    2016-09-01

    Stable transmission of a sub-μm-sized Ar8+ beam of 64-104-keV energy through glass tandem optics was achieved. The optics consisted of a 4-electrode tapered capillary and a sub-μm-sized tapered capillary tip, arranged in series. To actively discharge the capillary, and thus obtain stable transmission, an electrode was applied with a mechanical relay closing at a 0.01-0.1 Hz frequency. Transmitted beams were observed for tip outlets' diameters of 0.75 and 2.0 μm. When only a 4-electrode capillary was used, a beam density enhancement with a multiplicity of 14 times of the input beam density was achieved. A transmission efficiency up to 70% was observed with good reproducibility when the electrodes were biased with appropriate voltages.

  11. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW HEAVY-DUTY MOTOR VEHICLES Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Exhaust emission standards for CO2...

  12. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW HEAVY-DUTY MOTOR VEHICLES Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Exhaust emission standards for CO2...

  13. 40 CFR 1037.106 - Exhaust emission standards for CO2 for tractors above 26,000 pounds GVWR.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW HEAVY-DUTY MOTOR VEHICLES Emission Standards and Related Requirements § 1037.106 Exhaust emission standards for CO2 for tractors... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Exhaust emission standards for CO2...

  14. A powered roller/crimper for walk-behind tractors to terminate cover crops in conservation agriculture

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Roller/crimper implements have been used in large conservation farming systems to terminate cover crops near maturity and flatten them down to create a mulch through which cash crops can be planted directly into the cover residue. On small farms, tractors are usually small and less powerful relative...

  15. 29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... in 29 CFR 1928.51(a); (B) The following provisions address soil bank test conditions. (1) The test... specified in 29 CFR 1928.51. (b) Types of tests. All protective enclosures for wheel-type agricultural... following definitions shall apply: W = Tractor weight (see 29 CFR 1928.51(a)) in lb (W ′ in kg); E...

  16. 29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the weight defined in 29 CFR 1928.51(a); (B) The following provisions address soil bank test... specified in 29 CFR 1928.51. (b) Types of tests. All protective enclosures for wheel-type agricultural... following definitions shall apply: W = Tractor weight (see 29 CFR 1928.51(a)) in lb (W″ in kg); E...

  17. 29 CFR 1928.53 - Protective enclosures for wheel-type agricultural tractors-test procedures and performance...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... in 29 CFR 1928.51(a); (B) The following provisions address soil bank test conditions. (1) The test... specified in 29 CFR 1928.51. (b) Types of tests. All protective enclosures for wheel-type agricultural... following definitions shall apply: W = Tractor weight (see 29 CFR 1928.51(a)) in lb (W ′ in kg); E...

  18. 29 CFR 1928.52 - Protective frames for wheel-type agricultural tractors-test procedures and performance requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CFR 1928.51. (b) Types of tests. All protective frames for wheel-type agricultural tractors shall be... frame for compliance with the performance requirements of this standard. (2) Field-upset test. A field.... (vii) Rear input energy tests (static, dynamic, or field-upset) need not be performed on frames...

  19. 29 CFR 1928.52 - Protective frames for wheel-type agricultural tractors-test procedures and performance requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CFR 1928.51. (b) Types of tests. All protective frames for wheel-type agricultural tractors shall be... frame for compliance with the performance requirements of this standard. (2) Field-upset test. A field.... (vii) Rear input energy tests (static, dynamic, or field-upset) need not be performed on frames...

  20. 29 CFR 1926.1003 - Overhead protection for operators of agricultural and industrial tractors used in construction.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    .... The provisions of 29 CFR 1926.1001 for rubber-tired dozers and rubber-tired loaders may be used...) Purpose. When overhead protection is provided on wheel-type agricultural and industrial tractors, the... accidental upset. (2) Applicability. This standard applies to wheel-type agricultural and industrial...

  1. 29 CFR 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... STANDARDS FOR AGRICULTURE Roll-Over Protective Structures § 1928.51 Roll-over protective structures (ROPS..., designed to furnish the power to pull, carry, propel, or drive implements that are designed for agriculture... tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002...

  2. 29 CFR 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... STANDARDS FOR AGRICULTURE Roll-Over Protective Structures § 1928.51 Roll-over protective structures (ROPS..., designed to furnish the power to pull, carry, propel, or drive implements that are designed for agriculture... tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002...

  3. 29 CFR 1928.51 - Roll-over protective structures (ROPS) for tractors used in agricultural operations.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... STANDARDS FOR AGRICULTURE Roll-Over Protective Structures § 1928.51 Roll-over protective structures (ROPS..., designed to furnish the power to pull, carry, propel, or drive implements that are designed for agriculture... tractors shall meet the test and performance requirements of 29 CFR 1928.52, 1928.53, or 1926.1002...

  4. Optically active vacancies in GaN grown on Si substrates probed using a monoenergetic positron beam

    SciTech Connect

    Uedono, Akira Zhang, Yang; Yoshihara, Nakaaki; Fujishima, Tatsuya; Palacios, Tomás; Cao, Yu; Laboutin, Oleg; Johnson, Wayne; Ishibashi, Shoji; Sumiya, Masatomo

    2014-02-24

    Native defects in GaN layers grown on Si substrates by metal organic chemical vapor deposition have been studied using a monoenergetic positron beam. Measurements of Doppler broadening spectra of the annihilation radiation for GaN layers showed that optically active vacancy-type defects were formed in the layers. Charge transition of the defects due to electron capture was found to occur when the layers were irradiated by photons with energy above 2.71 eV. The concentration of such defects increased after 600–800 °C annealing, but the defects have not been annealed out even at 1000 °C. They were identified as Ga-vacancy-type defects, such as complexes between Ga vacancies and carbon impurities, and the relationship between their charge transition and optical properties were discussed.

  5. Active beam position stabilization of pulsed lasers for long-distance ion profile diagnostics at the Spallation Neutron Source (SNS).

    PubMed

    Hardin, Robert A; Liu, Yun; Long, Cary; Aleksandrov, Alexander; Blokland, Willem

    2011-02-14

    A high peak-power Q-switched laser has been used to monitor the ion beam profiles in the superconducting linac at the Spallation Neutron Source (SNS). The laser beam suffers from position drift due to movement, vibration, or thermal effects on the optical components in the 250-meter long laser beam transport line. We have designed, bench-tested, and implemented a beam position stabilization system by using an Ethernet CMOS camera, computer image processing and analysis, and a piezo-driven mirror platform. The system can respond at frequencies up to 30 Hz with a high position detection accuracy. With the beam stabilization system, we have achieved a laser beam pointing stability within a range of 2 μrad (horizontal) to 4 μrad (vertical), corresponding to beam drifts of only 0.5 mm × 1 mm at the furthest measurement station located 250 meters away from the light source.

  6. Active beam position stabilization of pulsed lasers for long-distance ion profile diagnostics at the Spallation Neutron Source (SNS)

    SciTech Connect

    Hardin, Robert A; Liu, Yun; Long, Cary D; Aleksandrov, Alexander V; Blokland, Willem

    2011-01-01

    A high peak-power Q-switched laser has been used to monitor the ion beam profiles in the superconducting linac at the Spallation Neutron Source (SNS). The laser beam suffers from position drift due to movement, vibration, or thermal effects on the optical components in the 250-meter long laser beam transport line. We have designed, bench-tested, and implemented a beam position stabilization system by using an Ethernet CMOS camera, computer image processing and analysis, and a piezo-driven mirror platform. The system can respond at frequencies up to 30 Hz with a high position detection accuracy. With the beam stabilization system, we have achieved a laser beam pointing stability within a range of 2 rad (horizontal) to 4 rad (vertical), corresponding to beam drifts of only 0.5 mm 1 mm at the furthest measurement station located 250 meters away from the light source.

  7. Active Interrogation of Sensitive Nuclear Material Using Laser Driven Neutron Beams

    SciTech Connect

    Favalli, Andrea; Roth, Markus

    2015-05-01

    An investigation of the viability of a laser-driven neutron source for active interrogation is reported. The need is for a fast, movable, operationally safe neutron source which is energy tunable and has high-intensity, directional neutron production. Reasons for the choice of neutrons and lasers are set forth. Results from the interrogation of an enriched U sample are shown.

  8. An active alignment method for post launch co-alignment of laser beam combiner systems

    NASA Technical Reports Server (NTRS)

    Yu, A. W.; Green, J. W.; Maynard, W. L.; Minott, P. O.; Krainak, M. A.

    1992-01-01

    A laser transmitter for high bandwidth geosynchronous satellite communications is described. High optical power is achieved by combining semiconductor laser diodes. An active alignment scheme is proposed for achieving the +/- 20 microrad post launch multiple laser angular co-alignment requirement.

  9. Geant4 simulation for a study of a possible use of carbon ion pencil beams for the treatment of ocular melanomas with the active scanning system at CNAO

    NASA Astrophysics Data System (ADS)

    Farina, E.; Piersimoni, P.; Riccardi, C.; Rimoldi, A.; Tamborini, A.; Ciocca, M.

    2015-12-01

    The aim of this work was to study a possible use of carbon ion pencil beams (delivered with active scanning modality) for the treatment of ocular melanomas at the Centro Nazionale di Adroterapia Oncologica (CNAO). The promising aspect of carbon ions radiotherapy for the treatment of this disease lies in its superior relative radio-biological effectiveness (RBE). The Monte Carlo (MC) Geant4 10.00 toolkit was used to simulate the complete CNAO extraction beamline, with the active and passive components along it. A human eye modeled detector, including a realistic target tumor volume, was used as target. Cross check with previous studies at CNAO using protons allowed comparisons on possible benefits on using such a technique with respect to proton beams. Experimental data on proton and carbon ion beams transverse distributions were used to validate the simulation.

  10. Development of in-series piezoelectric bimorph bending beam actuators for active flow control applications

    NASA Astrophysics Data System (ADS)

    Chan, Wilfred K.; Clingman, Dan J.; Amitay, Michael

    2016-04-01

    Piezoelectric materials have long been used for active flow control purposes in aerospace applications to increase the effectiveness of aerodynamic surfaces on aircraft, wind turbines, and more. Piezoelectric actuators are an appropriate choice due to their low mass, small dimensions, simplistic design, and frequency response. This investigation involves the development of piezoceramic-based actuators with two bimorphs placed in series. Here, the main desired characteristic was the achievable displacement amplitude at specific driving voltages and frequencies. A parametric study was performed, in which actuators with varying dimensions were fabricated and tested. These devices were actuated with a sinusoidal waveform, resulting in an oscillating platform on which to mount active flow control devices, such as dynamic vortex generators. The main quantification method consisted of driving these devices with different voltages and frequencies to determine their free displacement, blocking force, and frequency response. It was found that resonance frequency increased with shorter and thicker actuators, while free displacement increased with longer and thinner actuators. Integration of the devices into active flow control test modules is noted. In addition to physical testing, a quasi-static analytical model was developed and compared with experimental data, which showed close correlation for both free displacement and blocking force.

  11. Incorporation and Activation of Arsenic Dopant in Single-Crystal CdTe Grown on Si by Molecular Beam Epitaxy

    NASA Astrophysics Data System (ADS)

    Park, J. H.; Farrell, S.; Kodama, R.; Blissett, C.; Wang, X.; Colegrove, E.; Metzger, W. K.; Gessert, T. A.; Sivananthan, S.

    2014-08-01

    We report the use of molecular beam epitaxy to achieve p-type doping of CdTe grown on Si(211) substrates, by use of an arsenic cracker and post-growth annealing. A high hole density in CdTe is crucial for high efficiency II-VI-based solar cells. We measured the density of As in single-crystal CdTe by secondary ion mass spectroscopy; this showed that high As incorporation is achieved at low growth temperatures. Progressively higher incorporation was observed during low-temperature growth, presumably because of degradation of crystal quality with incorporation of As at such defect sites as dislocations and defect complexes. After As activation annealing under Hg overpressure, hole concentrations were obtained from Hall measurements. The highest doping level was ˜2.3 × 1016 cm-3, and near-1016 cm-3 doping was readily reproduced. The activation efficiency was ˜50%, but further optimization of the growth and annealing conditions is likely to improve this value.

  12. Quantitative Estimate of the Relation Between Rolling Resistance on Fuel Consumption of Class 8 Tractor Trailers Using Both New and Retreaded Tires (SAE Paper 2014-01-2425)

    EPA Science Inventory

    Road tests of class 8 tractor trailers were conducted by the US Environmental Protection Agency on new and retreaded tires of varying rolling resistance in order to provide estimates of the quantitative relationship between rolling resistance and fuel consumption.

  13. Activation caused by proton beam losses in Accelerator Production of Tritium LINAC

    SciTech Connect

    Beard, C.A.; Eaton, S.L.; Daemen, L.L.; Waters, L.S.; Wilson, W.B.

    1996-03-01

    A variety of accelerator designs are being considered for the Accelerator Production of Tritium (APT) project at Alamos National Laboratory. Because activation of the structural components of the accelerator is considered a major radiation protection issue, we have developed a computational methodology to estimate quantitatively radionuclide inventories and gamma dose rates resulting from accelerator operation. The work presented here illustrates the use of our computational methodology by focusing on the 20 and 100 MeV sections of the Bridge-Coupled Drift Tube LINAC (BCDTL), and the 100 and 1000 MeV sections of the Coupled Cavity LINAC (CCL).

  14. Intelligent controller for backing up a tractor-trailer truck using state transition table

    NASA Astrophysics Data System (ADS)

    Enab, Yehia M.

    1997-09-01

    The paper introduces a technique for constructing a look-up table that contains information about selected points in the state space of the nonlinear process to be controlled. The new states to which a specific state point transfers when the process is issued different control commands are registered. The controller designed to make use of the table depends on the heuristic assumption that the behavior of the process at a specific state space point is similar to its behavior at a nearby point provided that the process is issued a similar control command at each state. The table design aspects for reducing the storage requirements and minimizing the computational effort for producing control decisions are investigated. The applicability of the controller is tested for the tractor-trailer truck steering problem backing up at a constant speed. The truck backs up in an environment that contains obstacles to be avoided. Computer simulation of the truck and its controller has demonstrated workability.

  15. Aerodynamic drag reduction apparatus for gap-divided bluff bodies such as tractor-trailers

    DOEpatents

    Ortega, Jason M.; Salari, Kambiz

    2006-07-11

    An apparatus for reducing the aerodynamic drag of a bluff-bodied vehicle such as a tractor-trailer in a flowstream, the bluff-bodied vehicle of a type having a leading portion, a trailing portion connected to the leading portion, and a gap between the leading and trailing portions defining a recirculation zone. The apparatus is preferably a baffle assembly, such as a vertical panel, adapted to span a width of the gap between the leading and trailing portions so as to impede cross-flow through the gap, with the span of the baffle assembly automatically adjusting for variations in the gap width when the leading and trailing portions pivot relative to each other.

  16. A statistical description of the types and severities of accidents involving tractor semi-trailers

    SciTech Connect

    Clauss, D.B.; Wilson, R.K.; Blower, D.F.; Campbell, K.L.

    1994-06-01

    This report provides a statistical description of the types and severities of tractor semi-trailer accidents involving at least one fatality. The data were developed for use in risk assessments of hazardous materials transportation. Several accident databases were reviewed to determine their suitability to the task. The TIFA (Trucks Involved in Fatal Accidents) database created at the University of Michigan Transportation Research Institute was extensively utilized. Supplementary data on collision and fire severity, which was not available in the TIFA database, were obtained by reviewing police reports for selected TIFA accidents. The results are described in terms of frequencies of different accident types and cumulative distribution functions for the peak contact velocity, rollover skid distance, fire temperature, fire size, fire separation, and fire duration.

  17. Computational Flow Modeling of a Simplified Integrated Tractor-Trailer Geometry

    SciTech Connect

    Salari, K; McWherter-Payne, M

    2003-09-15

    For several years, Sandia National Laboratories and Lawrence Livermore National Laboratory have been part of a consortium funded by the Department of Energy to improve fuel efficiency of heavy vehicles such as Class 8 trucks through aerodynamic drag reduction. The objective of this work is to demonstrate the feasibility of using the steady Reynolds-Averaged Navier-Stokes (RANS) approach to predict the flow field around heavy vehicles, with special emphasis on the base region of the trailer, and to compute the aerodynamic forces. In particular, Sandia's computational fluid dynamics code, SACCARA, was used to simulate the flow on a simplified model of a tractor-trailer vehicle. The results are presented and compared with NASA Ames experimental data to assess the predictive capability of RANS to model the flow field and predict the aerodynamic forces.

  18. Computational flow modeling of a simplified integrated tractor-trailer geometry.

    SciTech Connect

    McWherter-Payne, Mary Anna; Salari, Kambiz

    2003-09-01

    For several years, Sandia National Laboratories and Lawrence Livermore National Laboratory have been part of a consortium funded by the Department of Energy to improve fuel efficiency of heavy vehicles such as Class 8 trucks through aerodynamic drag reduction. The objective of this work is to demonstrate the feasibility of using the steady Reynolds-Averaged Navier-Stokes (RANS) approach to predict the flow field around heavy vehicles, with special emphasis on the base region of the trailer, and to compute the aerodynamic forces. In particular, Sandia's computational fluid dynamics code, SACCARA, was used to simulate the flow on a simplified model of a tractor-trailer vehicle. The results are presented and compared with NASA Ames experimental data to assess the predictive capability of RANS to model the flow field and predict the aerodynamic forces.

  19. The Effect of Propellers and Nacelles on the Landing Speeds of Tractor Monoplanes

    NASA Technical Reports Server (NTRS)

    Windler, Ray

    1932-01-01

    This paper reports wind-tunnel tests giving the lift coefficients of large-scale wing-nacelle combinations both with and without the propeller. The tests were made to show the effect of nacelles, and idling and stopped propellers on the landing speeds of tractor monoplanes. Four types of nacelles with various cowlings were used in numerous positions with respect to both a Clark Y and a thick airfoil. The effect of both the idling and stopped propeller on lift, and consequently on landing speed, was negligible. A nacelle with exposed engine cylinders when placed directly in front of an airfoil caused a slight reduction in lift, consequently an increase in landing speed, over the condition with the wing alone. With this exception no appreciable effect on landing speed was indicated for any of the other combinations.

  20. Steering a Tractor by Means of an EMG-Based Human-Machine Interface

    PubMed Central

    Gomez-Gil, Jaime; San-Jose-Gonzalez, Israel; Nicolas-Alonso, Luis Fernando; Alonso-Garcia, Sergio

    2011-01-01

    An electromiographic (EMG)-based human-machine interface (HMI) is a communication pathway between a human and a machine that operates by means of the acquisition and processing of EMG signals. This article explores the use of EMG-based HMIs in the steering of farm tractors. An EPOC, a low-cost human-computer interface (HCI) from the Emotiv Company, was employed. This device, by means of 14 saline sensors, measures and processes EMG and electroencephalographic (EEG) signals from the scalp of the driver. In our tests, the HMI took into account only the detection of four trained muscular events on the driver’s scalp: eyes looking to the right and jaw opened, eyes looking to the right and jaw closed, eyes looking to the left and jaw opened, and eyes looking to the left and jaw closed. The EMG-based HMI guidance was compared with manual guidance and with autonomous GPS guidance. A driver tested these three guidance systems along three different trajectories: a straight line, a step, and a circumference. The accuracy of the EMG-based HMI guidance was lower than the accuracy obtained by manual guidance, which was lower in turn than the accuracy obtained by the autonomous GPS guidance; the computed standard deviations of error to the desired trajectory in the straight line were 16 cm, 9 cm, and 4 cm, respectively. Since the standard deviation between the manual guidance and the EMG-based HMI guidance differed only 7 cm, and this difference is not relevant in agricultural steering, it can be concluded that it is possible to steer a tractor by an EMG-based HMI with almost the same accuracy as with manual steering. PMID:22164006

  1. Long hours and fatigue: a survey of tractor-trailer drivers.

    PubMed

    Braver, E R; Preusser, C W; Preusser, D F; Baum, H M; Beilock, R; Ulmer, R

    1992-01-01

    Fatigue and long driving hours have been implicated as risk factors in truck crashes. Under federal regulations, commercial drivers are permitted to drive no more than 10 hours before having an 8-hour break and cannot work more than 70 hours over an 8-day period. Several studies have suggested that violations of these rules are common. A survey of long haul tractor-trailer drivers was conducted to estimate what proportion of drivers report that they regularly violate the hours-of-service rules and to identify the drivers most likely to commit hours-of-service violations. During December 1990 through April 1991, a total of 1,249 drivers were interviewed at truck safety inspection stations, truck stops, and agricultural inspection stations in Connecticut, Florida, Oklahoma, and Oregon. In each state, interviews were conducted during varying periods of the day over the course of seven days at inspection stations. Overall, 89 percent of eligible drivers asked for interviews participated in the survey. According to self-reports, almost three-fourths of the respondents violate hours-of-service rules. About two-thirds of the drivers reported that they routinely drive or work more than the weekly maximum. A primary impetus for violating rules appears to be economic factors, including tight delivery schedules and low payment rates. Many other driver, job, and vehicle characteristics were significantly associated with being an hours-of-service violator. The high prevalence of hours-of-service violations among tractor-trailer drivers is a problem in need of urgent attention. Potential measures to reduce the prevalence of rules violations include more enforcement directed toward carriers, wider use of electronic recorders, and increasing the number of rest areas.

  2. Steering a tractor by means of an EMG-based human-machine interface.

    PubMed

    Gomez-Gil, Jaime; San-Jose-Gonzalez, Israel; Nicolas-Alonso, Luis Fernando; Alonso-Garcia, Sergio

    2011-01-01

    An electromiographic (EMG)-based human-machine interface (HMI) is a communication pathway between a human and a machine that operates by means of the acquisition and processing of EMG signals. This article explores the use of EMG-based HMIs in the steering of farm tractors. An EPOC, a low-cost human-computer interface (HCI) from the Emotiv Company, was employed. This device, by means of 14 saline sensors, measures and processes EMG and electroencephalographic (EEG) signals from the scalp of the driver. In our tests, the HMI took into account only the detection of four trained muscular events on the driver's scalp: eyes looking to the right and jaw opened, eyes looking to the right and jaw closed, eyes looking to the left and jaw opened, and eyes looking to the left and jaw closed. The EMG-based HMI guidance was compared with manual guidance and with autonomous GPS guidance. A driver tested these three guidance systems along three different trajectories: a straight line, a step, and a circumference. The accuracy of the EMG-based HMI guidance was lower than the accuracy obtained by manual guidance, which was lower in turn than the accuracy obtained by the autonomous GPS guidance; the computed standard deviations of error to the desired trajectory in the straight line were 16 cm, 9 cm, and 4 cm, respectively. Since the standard deviation between the manual guidance and the EMG-based HMI guidance differed only 7 cm, and this difference is not relevant in agricultural steering, it can be concluded that it is possible to steer a tractor by an EMG-based HMI with almost the same accuracy as with manual steering.

  3. Active control for vibration suppression in a flexible beam using a modal domain optical fiber sensor

    NASA Technical Reports Server (NTRS)

    Cox, D. E.; Lindner, D. K.

    1991-01-01

    An account is given of the use of a modal-domain (MD) fiber-optic sensor as an active control system component for vibration suppression, whose output is proportional to the integral of the axial strain along the optical fiber. When an MD sensor is attached to, or embedded in, a flexible structure, it senses the strain in the structure along its gage length. On the basis of the present integration of the sensor model into a flexible-structure model, it becomes possible to design a control system with a dynamic compensator which adds damping to the low-order modes of the flexible structure. This modeling procedure has been experimentally validated.

  4. A Demonstration Project in New York and Virginia: Retrofitting Cost-Effective Roll-over Protective Structures (CROPS) on Tractors.

    PubMed

    Hard, D L; McKenzie, E A; Cantis, D; May, J; Sorensen, J; Bayes, B; Madden, E; Wyckoff, S; Stone, B; Maass, J

    2015-07-01

    The NIOSH cost-effective roll-over protective structure (CROPS) demonstration project sought to determine whether three prototype roll-over protective structures (ROPS) designed to be retrofitted on Ford 8N, Ford 3000, Ford 4000, and Massey Ferguson 135 tractors could be installed in the field and whether they would be acceptable by the intended end users (farmers). There were a total of 50 CROPS. demonstrators (25 in New York and 25 in Virginia), with 45 observers attending the New York CROPS demonstrations and 36 observers attending the Virginia CROPS demonstrations, for a total of 70 participants in New York and 61 in Virginia. The oldest retrofitted tractors were 77 to 62 years old, while the newest retrofitted tractors were 40 to 37 years old. The most frequently retrofitted tractor in the CROPS demonstration project was a Ford 3000 series tractor (n = 19; 38%), followed by Ford 4000 (n = 11; 22%), Massey Ferguson 135 (n = 11; 22%), and Ford 8N (n = 9; 18%). A major issue of CROPS retrofitting was the rear wheel fenders. The effort involved in disassembling the fenders (removing the old bolts was often faster by cutting them with a torch), modifying the fender mounting brackets, and then reinstalling the fenders with the CROPS generally required the most time. In addition, various other semi-permanent equipment attachments, such as front-end loaders, required additional time and effort to fit with the CROPS. Demonstrators were asked to rank the reasons why they had not retrofitted their tractors with ROPS until they had enrolled in the CROPS demonstration program. ROPS "cost too much" was ranked as the primary reason for participants in both states (80% for New York and 88% for Virginia). The second highest ranked reasons were "ROPS wasn't available" for Virginia (80%) and "hassle to find ROPS" for New York (69%). The third highest ranked reasons were "not enough time to find ROPS" for New York (67%) and "hassle to find ROPS" for Virginia (79%). All

  5. A Demonstration Project in New York and Virginia: Retrofitting Cost-Effective Roll-over Protective Structures (CROPS) on Tractors

    PubMed Central

    Hard, David L.; McKenzie, E. A.; Cantis, Douglas; May, John; Sorensen, Julie; Bayes, Barbara; Madden, Erin; Wyckoff, Sherry; Stone, Bruce; Maass, Jimmy

    2015-01-01

    The NIOSH cost-effective roll-over protective structure (CROPS) demonstration project sought to determine whether three prototype roll-over protective structures (ROPS) designed to be retrofitted on Ford 8N, Ford 3000, Ford 4000, and Massey Ferguson 135 tractors could be installed in the field and whether they would be acceptable by the intended end users (farmers). There were a total of 50 CROPS demonstrators (25 in New York and 25 in Virginia), with 45 observers attending the New York CROPS demonstrations and 36 observers attending the Virginia CROPS demonstrations, for a total of 70 participants in New York and 61 in Virginia. The oldest retrofitted tractors were 77 to 62 years old, while the newest retrofitted tractors were 40 to 37 years old. The most frequently retrofitted tractor in the CROPS demonstration project was a Ford 3000 series tractor (n = 19; 38%), followed by Ford 4000 (n = 11; 22%), Massey Ferguson 135 (n = 11; 22%), and Ford 8N (n = 9; 18%). A major issue of CROPS retrofitting was the rear wheel fenders. The effort involved in disassembling the fenders (removing the old bolts was often faster by cutting them with a torch), modifying the fender mounting brackets, and then reinstalling the fenders with the CROPS generally required the most time. In addition, various other semi-permanent equipment attachments, such as front-end loaders, required additional time and effort to fit with the CROPS. Demonstrators were asked to rank the reasons why they had not retrofitted their tractors with ROPS until they had enrolled in the CROPS demonstration program. ROPS “cost too much” was ranked as the primary reason for participants in both states (80% for New York and 88% for Virginia). The second highest ranked reasons were “ROPS wasn’t available” for Virginia (80%) and “hassle to find ROPS” for New York (69%). The third highest ranked reasons were “not enough time to find ROPS” for New York (67%) and “hassle to find ROPS” for Virginia

  6. Proton beam simulation with MCNPX: Gallium metal activation estimates below 30 MeV relevant to the bulk production of 68Ge and 65Zn

    NASA Astrophysics Data System (ADS)

    Fassbender, M.; Arzumanov, A.; Jamriska, D. J.; Lyssukhin, S. N.; Trellue, H.; Waters, L. S.

    2007-08-01

    Several gallium metal targets containing Ga metal encapsulated in Nb shells were irradiated in a 30 MeV cyclotron beam. Proton and secondary neutron beam fluences as well as radionuclide activity formation were modeled using MCNP-X in combination with CINDER90. Targets were chemically processed using two anion exchange steps. Good agreement between measured radiochemical yields and MCNPX/CINDER estimates was observed. The separation principle introduced in this work was utilized for a small 68Ge/Ga generator column for 68Ga labeling purposes.

  7. Approximating ambient D-region electron densities using dual-beam HF heating experiments at the high-frequency Active Auroral Research Program (HAARP)

    NASA Astrophysics Data System (ADS)

    Agrawal, Divya

    Dual-beam ELF/VLF wave generation experiments performed at the High-frequency Active Auroral Research Program (HAARP) HF transmitter in Gakona, Alaska are critically compared with the predictions of a newly developed ionospheric high frequency (HF) heating model that accounts for the simultaneous propagation and absorption of multiple HF beams. The dual-beam HF heating experiments presented herein consist of two HF beams transmitting simultaneously: one amplitude modulated (AM) HF beam modulates the conductivity of the lower ionosphere in the extremely low frequency (ELF, 30 Hz to 3 kHz) and/or very low frequency (VLF, 3 kHz to 30 kHz) band while a second HF beam broadcasts a continuous waveform (CW) signal, modifying the efficiency of ELF/VLF conductivity modulation and thereby the efficiency of ELF/VLF wave generation. Ground-based experimental observations are used together with the predictions of the theoretical model to identify the property of the received ELF/VLF wave that is most sensitive to the effects of multi-beam HF heating, and that property is determined to be the ELF/VLF signal magnitude. The dependence of the generated ELF/VLF wave magnitude on several HF transmission parameters (HF power, HF frequency, and modulation waveform) is then experimentally measured and analyzed within the context of the multi-beam HF heating model. For all cases studied, the received ELF/VLF wave magnitude as a function of transmission parameter is analyzed to identify the dependence on the ambient D-region electron density (Ne) and/or electron temperature ( Te), in turn identifying the HF transmission parameters that provide significant independent information regarding the ambient conditions of the D-region ionosphere. A theoretical analysis is performed to determine the conditions under which the effects of Ne and Te can be decoupled, and the results of this analysis are applied to identify an electron density profile that can reproduce the unusually high level of ELF

  8. An overview of the facilities, activities, and developments at the University of North Texas Ion Beam Modification and Analysis Laboratory (IBMAL)

    SciTech Connect

    Rout, Bibhudutta; Dhoubhadel, Mangal S.; Poudel, Prakash R.; Kummari, Venkata C.; Pandey, Bimal; Deoli, Naresh T.; Lakshantha, Wickramaarachchige J.; Mulware, Stephen J.; Baxley, Jacob; Manuel, Jack E.; Pacheco, Jose L.; Szilasi, Szabolcs; Weathers, Duncan L.; Reinert, Tilo; Glass, Gary A.; Duggan, Jerry L.; McDaniel, Floyd D.

    2013-07-03

    The Ion Beam Modification and Analysis Laboratory (IBMAL) at the University of North Texas includes several accelerator facilities with capabilities of producing a variety of ion beams from tens of keV to several MeV in energy. The four accelerators are used for research, graduate and undergraduate education, and industrial applications. The NEC 3MV Pelletron tandem accelerator has three ion sources for negative ions: He Alphatross and two different SNICS-type sputter ion sources. Presently, the tandem accelerator has four high-energy beam transport lines and one low-energy beam transport line directly taken from the negative ion sources for different research experiments. For the low-energy beam line, the ion energy can be varied from {approx}20 to 80 keV for ion implantation/modification of materials. The four post-acceleration beam lines include a heavy-ion nuclear microprobe; multi-purpose PIXE, RBS, ERD, NRA, and broad-beam single-event upset; high-energy ion implantation line; and trace-element accelerator mass spectrometry. The NEC 3MV single-ended Pelletron accelerator has an RF ion source mainly for hydrogen, helium and heavier inert gases. We recently installed a capacitive liner to the terminal potential stabilization system for high terminal voltage stability and high-resolution microprobe analysis. The accelerator serves a beam line for standard RBS and RBS/C. Another beamline for high energy focused ion beam application using a magnetic quadrupole lens system is currently under construction. This beam line will also serve for developmental work on an electrostatic lens system. The third accelerator is a 200 kV Cockcroft-Walton accelerator with an RF ion source. The fourth accelerator is a 2.5 MV Van de Graaff accelerator, which was in operation for last several decades is currently planned to be used mainly for educational purpose. Research projects that will be briefly discussed include materials synthesis/modification for photonic, electronic, and

  9. SU-D-BRF-01: Applications of Photonuclear Activation of Biological Tissues in Clinical High-Energy X-Ray Beams

    SciTech Connect

    Veltchev, I; Fourkal, E; Ma, C

    2014-06-01

    Purpose: The commercial availability of high-energy accelerators opens new therapeutic opportunities for X-rays with energies in excess of 15MV. Three clinical beams (Varian 18MV, Elekta SL25, and Top Grade LA45) were compared by the production of photo-activated positron emitters in five types of biological tissues. Methods: The activation studies were performed using FLUKA2011 Monte Carlo suite with beam models designed for the three accelerators. Absolute activity density (Bq/ml) distribution in space was obtained from this study. Additionally, the temporal evolution of all activated species was monitored for cooling times up to 30 minutes. Results: The relative activation contrast of tissue pairs was evaluated for 2Gy of dose at 10cm depth for five tissues (normal, hypoxic, adipose, bone, and lung). In bone the sort-lived isotopes O-15 and P-30 dominated the activity at the early cooling stages. In all tissues 15 minutes post-irradiation the C-11 activity became dominant. Tissues with higher carbon-to-oxygen ratio in their elemental composition became clearly visible in a PET scan at longer cooling times. Radiation treatment of a lung tumor with a hypoxic core was simulated in an anthropomorphic phantom using the LA45 beam model. Increase in the PET counts by more than 50% was measured in the hypoxic volume 15 minutes post-irradiation, demonstrating the benefits of the relative activation contrast concept. Conclusion: LA45 beam is found to produce measurable activation distribution for 2Gy of dose, suitable for tissue type discrimination studies. Maximum activation contrast of 1.7 between hypoxic and normal tissues was measured in a simulated treatment. The absolute activity density values obtained from these Monte Carlo studies suggest that the window of opportunity for a PET scan exists up to 60 minutes after 2Gy of dose is deposited by 45MV X-ray beam. Lung-to-tissue activation contrast can be explored for treatment QA purposes as well.

  10. Transparent and electrically conductive GaSb/Si direct wafer bonding at low temperatures by argon-beam surface activation

    NASA Astrophysics Data System (ADS)

    Predan, F.; Reinwand, D.; Klinger, V.; Dimroth, F.

    2015-10-01

    Direct wafer bonds of the material system n-GaSb/n-Si have been achieved by means of a low-temperature direct wafer bonding process, enabling an optical transparency of the bonds along with a high electrical conductivity of the boundary layer. In the used technique, the surfaces are activated by sputter-etching with an argon fast-atom-beam (FAB) and bonded in ultra-high vacuum. The bonds were annealed at temperatures between 300 and 400 °C, followed by an optical, mechanical and electrical characterization of the interface. Additionally, the influence of the sputtering on the surface topography of the GaSb was explicitly investigated. Fully bonded wafer pairs with high bonding strengths were found, as no blade could be inserted into the bonds without destroying the samples. The interfacial resistivities of the bonded wafers were significantly reduced by optimizing the process parameters, by which Ohmic interfacial resistivities of less than 5 mΩ cm2 were reached reproducibly. These promising results make the monolithic integration of GaSb on Si attractive for various applications.

  11. Active fiber-based retroreflector providing phase-retracing anti-parallel laser beams for precision spectroscopy.

    PubMed

    Beyer, A; Maisenbacher, L; Matveev, A; Pohl, R; Khabarova, K; Chang, Y; Grinin, A; Lamour, T; Shi, T; Yost, D C; Udem, Th; Hänsch, T W; Kolachevsky, N

    2016-07-25

    We present an active fiber-based retroreflector providing high quality phase-retracing anti-parallel Gaussian laser beams for precision spectroscopy of Doppler sensitive transitions. Our design is well-suited for a number of applications where implementing optical cavities is technically challenging and corner cubes fail to match the demanded requirements, most importantly retracing wavefronts and preservation of the laser polarization. To illustrate the performance of the system, we use it for spectroscopy of the 2S-4P transition in atomic hydrogen and demonstrate an average suppression of the first order Doppler shift to 4 parts in 106 of the full collinear shift. This high degree of cancellation combined with our cryogenic source of hydrogen atoms in the metastable 2S state is sufficient to enable determinations of the Rydberg constant and the proton charge radius with competitive uncertainties. Advantages over the usual Doppler cancellation based on corner cube type retroreflectors are discussed as well as an alternative method using a high finesse cavity. PMID:27464193

  12. A Study of The Effect of Preschool Children's Participation in Sensorimotor Activities on Their Understanding of the Mechanical Equilibrium of a Balance Beam

    NASA Astrophysics Data System (ADS)

    Hadzigeorgiou, Yannis; Anastasiou, Leonidas; Konsolas, Manos; Prevezanou, Barbara

    2009-01-01

    The purpose of this study was to investigate whether participation in sensorimotor activities by preschool children involving their own bodily balance while walking on a beam over the floor has an effect on their understanding of the mechanical equilibrium of a balance beam. The balance beam consisted of a horizontal stick balancing around its center of mass (middle point), while carrying equal-weight objects on either side of it. The study utilized a two-group design, and was conducted in three phases (pre-test, treatment and post-test). The results of the study provide evidence that there was such an effect, since the children (who participated in the sensorimotor activities) could select out of a number of objects those two with the same weight regardless of their shape, size or colour, in order to balance the stick. This effect also can be seen when a comparison is made with a second group of children, which had previously participated in a hands-on activity regarding the equilibrium of a similar balance beam, and which (children), therefore, had a definite advantage over the other children who had participated in the sensorimotor activity. A Chi Square Test showed no significant differences between the two groups on both an immediate and a delayed post-test, while the McNemar Test for the Significance of Change showed a statistically significant difference (that is, a negative change in performance between the first and the second post-test) only within the hands-on group. This difference represents evidence that the children from the sensorimotor group remembered better the rule they were applying (i.e., selecting equal-weight objects) in order to balance the beam.

  13. Calibration and algorithm development for estimation of nitrogen in wheat crop using tractor mounted N-sensor.

    PubMed

    Singh, Manjeet; Kumar, Rajneesh; Sharma, Ankit; Singh, Bhupinder; Thind, S K

    2015-01-01

    The experiment was planned to investigate the tractor mounted N-sensor (Make Yara International) to predict nitrogen (N) for wheat crop under different nitrogen levels. It was observed that, for tractor mounted N-sensor, spectrometers can scan about 32% of total area of crop under consideration. An algorithm was developed using a linear relationship between sensor sufficiency index (SIsensor) and SISPAD to calculate the N app as a function of SISPAD. There was a strong correlation among sensor attributes (sensor value, sensor biomass, and sensor NDVI) and different N-levels. It was concluded that tillering stage is most prominent stage to predict crop yield as compared to the other stages by using sensor attributes. The algorithms developed for tillering and booting stages are useful for the prediction of N-application rates for wheat crop. N-application rates predicted by algorithm developed and sensor value were almost the same for plots with different levels of N applied. PMID:25811039

  14. Calibration and Algorithm Development for Estimation of Nitrogen in Wheat Crop Using Tractor Mounted N-Sensor

    PubMed Central

    Singh, Manjeet; Kumar, Rajneesh; Sharma, Ankit; Singh, Bhupinder; Thind, S. K.

    2015-01-01

    The experiment was planned to investigate the tractor mounted N-sensor (Make Yara International) to predict nitrogen (N) for wheat crop under different nitrogen levels. It was observed that, for tractor mounted N-sensor, spectrometers can scan about 32% of total area of crop under consideration. An algorithm was developed using a linear relationship between sensor sufficiency index (SIsensor) and SISPAD to calculate the Napp as a function of SISPAD. There was a strong correlation among sensor attributes (sensor value, sensor biomass, and sensor NDVI) and different N-levels. It was concluded that tillering stage is most prominent stage to predict crop yield as compared to the other stages by using sensor attributes. The algorithms developed for tillering and booting stages are useful for the prediction of N-application rates for wheat crop. N-application rates predicted by algorithm developed and sensor value were almost the same for plots with different levels of N applied. PMID:25811039

  15. Experimental verification of proton beam monitoring in a human body by use of activity image of positron-emitting nuclei generated by nuclear fragmentation reaction.

    PubMed

    Nishio, Teiji; Miyatake, Aya; Inoue, Kazumasa; Gomi-Miyagishi, Tomoko; Kohno, Ryosuke; Kameoka, Satoru; Nakagawa, Keiichi; Ogino, Takashi

    2008-01-01

    Proton therapy is a form of radiotherapy that enables concentration of dose on a tumor by use of a scanned or modulated Bragg peak. Therefore, it is very important to evaluate the proton-irradiated volume accurately. The proton-irradiated volume can be confirmed by detection of pair-annihilation gamma rays from positron-emitting nuclei generated by the nuclear fragmentation reaction of the incident protons on target nuclei using a PET apparatus. The activity of the positron-emitting nuclei generated in a patient was measured with a PET-CT apparatus after proton beam irradiation of the patient. Activity measurement was performed in patients with tumors of the brain, head and neck, liver, lungs, and sacrum. The 3-D PET image obtained on the CT image showed the visual correspondence with the irradiation area of the proton beam. Moreover, it was confirmed that there were differences in the strength of activity from the PET-CT images obtained at each irradiation site. The values of activity obtained from both measurement and calculation based on the reaction cross section were compared, and it was confirmed that the intensity and the distribution of the activity changed with the start time of the PET imaging after proton beam irradiation. The clinical use of this information about the positron-emitting nuclei will be important for promoting proton treatment with higher accuracy in the future.

  16. Tractor-trailer crashes in Indiana: a case-control study of the role of truck configuration.

    PubMed

    Braver, E R; Zador, P L; Thum, D; Mitter, E L; Baum, H M; Vilardo, F J

    1997-01-01

    Studies of the crash experience of tractors pulling multiple trailers have reached different conclusions concerning the relationship of truck configuration to crash risk. A previous case-control study found a significant increase in crash risk for double-trailer trucks in the state of Washington. The present case-control study was done of tractor-trailers crashing on Indiana interstates during November 1989-March 1991. Controls were obtained for 25% of the crash sites and were all tractor-trailers passing the crash sites during a traffic observation session one to four weeks following a crash on the same day of the week for 30 minutes at the same time of day. Logistic regression identified day of week, time of day, urban/rural area, and specific highway as significant predictors of controls' truck configuration. This model was applied to the cases to estimate the expected number of double-trailer cases. For all crashes combined, no increased crash risk was observed for doubles (Standardized Crash Ratio (SCR) = 83). Doubles were significantly underinvolved in multiple-vehicle crashes (SCR = 74), crashes on dry roads (SCR = 61), and crashes on wet (other than snow, ice, or slush) roads (SCR = 54). Doubles were significantly overinvolved in crashes on roads with snow, ice, or slush (SCR = 153). Because truck configuration was highly associated with driver age and work operation attributes among trucks in crashes, the absence of control data on these potential confounders precluded definitive assessment of the intrinsic risk of multiple versus single-trailer vehicles.

  17. Control over the morphology of AlN during molecular beam epitaxy with the plasma activation of nitrogen on Si (111) substrates

    SciTech Connect

    Mizerov, A. M. Kladko, P. N.; Nikitina, E. V.; Egorov, A. Yu.

    2015-02-15

    The results of studies of the growth kinetics of AlN layers during molecular beam epitaxy with the plasma activation of nitrogen using Si (111) substrates are presented. The possibility of the growth of individual AlN/Si (111) nanocolumns using growth conditions with enrichment of the surface with metal near the formation mode of Al drops, at a substrate temperature close to maximal, during molecular beam epitaxy with the plasma activation of nitrogen (T{sub s} ≈ 850°C) is shown. The possibility of growing smooth AlN layers on a nanocolumnar AlN/Si (111) buffer with the use of T{sub s} ≈ 750°C and growth conditions providing enrichment with metal is shown.

  18. Test, Evaluation, and Demonstration of Practical Devices/Systems to Reduce Aerodynamic Drag of Tractor/Semitrailer Combination Unit Trucks

    SciTech Connect

    Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond

    2007-04-30

    Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their effect on

  19. An investigation of drag reduction for tractor trailer vehicles with air deflector and boattail. Final report

    SciTech Connect

    Muirhead, V.U.

    1981-01-01

    A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a trailer model. The physical variables included: a cab mounted wind deflector, boattail on trailer, flow vanes on trailer front, forced transition on trailer, and decreased gap between tractor and trailer. Tests were conducted at yaw angles (relative wind angles) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.58 x 10 to the 5th power 6.12 x 10 to the 5th power based upon the equivalent diameter of the vehicles. The wind deflector on top of the cab produced a calculated reduction in fuel consumption of about 5 percent of the aerodynamic portion of the fuel budget for a wind speed of 15.3 km/hr (9.5 mph) over a wind angle range of 0 deg to 180 deg and for a vehicle speed of 88.5 km/hr (55 mph). The boattail produced a calculated 7 percent to 8 percent reduction in fuel consumption under the same conditions. The decrease in gap reduced the calculated fuel consumption by about 5 percent of the aerodynamic portion of the fuel budget.

  20. Reverse propagation and negative angular momentum density flux of an optical nondiffracting nonparaxial fractional Bessel vortex beam of progressive waves.

    PubMed

    Mitri, F G

    2016-09-01

    Energy and angular momentum flux density characteristics of an optical nondiffracting nonparaxial vector Bessel vortex beam of fractional order are examined based on the dual-field method for the generation of symmetric electric and magnetic fields. Should some conditions determined by the polarization state, the half-cone angle as well as the beam-order (or topological charge) be met, the axial energy and angular momentum flux densities vanish (representing Poynting singularities), before they become negative. These negative counterintuitive properties suggest retrograde (negative) propagation as well as a rotation reversal of the angular momentum with respect to the beam handedness. These characteristics of nondiffracting nonparaxial Bessel fractional vortex beams of progressive waves open new capabilities in optical tractor beam tweezers, optical spanners, invisibility cloaks, optically engineered metamaterials, and other applications. PMID:27607486

  1. Reverse propagation and negative angular momentum density flux of an optical nondiffracting nonparaxial fractional Bessel vortex beam of progressive waves.

    PubMed

    Mitri, F G

    2016-09-01

    Energy and angular momentum flux density characteristics of an optical nondiffracting nonparaxial vector Bessel vortex beam of fractional order are examined based on the dual-field method for the generation of symmetric electric and magnetic fields. Should some conditions determined by the polarization state, the half-cone angle as well as the beam-order (or topological charge) be met, the axial energy and angular momentum flux densities vanish (representing Poynting singularities), before they become negative. These negative counterintuitive properties suggest retrograde (negative) propagation as well as a rotation reversal of the angular momentum with respect to the beam handedness. These characteristics of nondiffracting nonparaxial Bessel fractional vortex beams of progressive waves open new capabilities in optical tractor beam tweezers, optical spanners, invisibility cloaks, optically engineered metamaterials, and other applications.

  2. Effects of prenatal irradiation with accelerated heavy-ion beams on postnatal development in rats: III. Testicular development and breeding activity

    NASA Astrophysics Data System (ADS)

    Wang, B.; Murakami, M.; Eguchi-Kasai, K.; Nojima, K.; Shang, Y.; Tanaka, K.; Watanabe, K.; Fujita, K.; Moreno, S. G.; Coffigny, H.; Hayata, I.

    With a significant increase in human activities dealing with space missions, potential teratogenic effects on the mammalian reproductive system from prenatal exposure to space radiation have become a hot topic that needs to be addressed. However, even for the ground experiments, such effects from exposure to high LET ionizing radiation are not as well studied as those for low LET ionizing radiations such as X-rays. Using the Heavy-Ion Medical Accelerator in Chiba (HIMAC) and Wistar rats, effects on gonads in prenatal male fetuses, on postnatal testicular development and on breeding activity of male offspring were studied following exposure of the pregnant animals to either accelerated carbon-ion beams with a LET value of about 13 keV/μm or neon-ion beams with a LET value of about 30 keV/μm at a dose range from 0.1 to 2.0 Gy on gestation day 15. The effects of X-rays at 200 kVp estimated for the same biological end points were studied for comparison. A significantly dose-dependent increase of apoptosis in gonocytes appeared 6 h after irradiations with a dose of 0.5 Gy or more. Measured delayed testis descent and malformed testicular seminiferous tubules were observed to be significantly different from the control animals at a dose of 0.5 Gy. These effects are observed to be dose- and LET-dependent. Markedly reduced testicular weight and testicular weight to body weight ratio were scored at postnatal day 30 even in the offspring that were prenatally irradiated with neon-ions at a dose of 0.1 Gy. A dose of 0.5 Gy from neon-ion beams induced a marked decrease in breeding activity in the prenatally irradiated male rats, while for the carbon-ion beams or X-rays, the significantly reduced breeding activity was observed only when the prenatal dose was at 1.0 Gy or more. These findings indicated that prenatal irradiations with heavy-ion beams on gestation day 15 generally induced markedly detrimental effects on prenatal gonads, postnatal testicular development and male

  3. Neutral particle beam intensity controller

    DOEpatents

    Dagenhart, William K.

    1986-01-01

    A neutral beam intensity controller is provided for a neutral beam generator in which a neutral beam is established by accelerating ions from an ion source into a gas neutralizer. An amplitude modulated, rotating magnetic field is applied to the accelerated ion beam in the gas neutralizer to defocus the resultant neutral beam in a controlled manner to achieve intensity control of the neutral beam along the beam axis at constant beam energy. The rotating magnetic field alters the orbits of ions in the gas neutralizer before they are neutralized, thereby controlling the fraction of neutral particles transmitted out of the neutralizer along the central beam axis to a fusion device or the like. The altered path or defocused neutral particles are sprayed onto an actively cooled beam dump disposed perpendicular to the neutral beam axis and having a central open for passage of the focused beam at the central axis of the beamline. Virtually zero therough 100% intensity control is achieved by varying the magnetic field strength without altering the ion source beam intensity or its species yield.

  4. Effect of E-beam treatment on the chemistry and on the antioxidant activity of lycopene from dry tomato peel and tomato powder.

    PubMed

    Gámez, M Carmen; Calvo, Marta M; Selgas, M Dolores; García, M Luisa; Erler, Katrin; Böhm, Volker; Catalano, Assunta; Simone, Rossella; Palozza, Paola

    2014-02-19

    Tomato powder (TP) and dry tomato peel (DTP) have been previously used in our laboratory as a source of lycopene to manufacture meat products ready-to-eat (RTE) submitted to E-beam irradiation with good technological and sensory results. Present work describes the studies performed in order to investigate the effect of radiation on chemical changes and antioxidant properties of lycopene. DTP and TP were irradiated (4 kGy). Changes on lycopene were analyzed by HPLC; inhibition of reactive oxygen species (ROS), possible modulation of mitogen-activated protein kinases (MAPK) cascade, nuclear factor κ-light-chain-enhancer of activated B cells (NP-κB) activation and expression of proteins involved in oxidation stress were analyzed in RAT-1 fibroblasts cell culture. Radiation reduced the content of all-E-lycopene and increased (Z)-lycopene, lycopene isomerization, and degradation being higher in DTP than in TP. E-Beam treatment increased the antioxidant ability of both DTP and TP in inhibiting spontaneous and H2O2-induced oxidative stress in cultured fibroblasts. Antioxidant activity was higher in DTP than in TP samples.

  5. Effect of E-beam treatment on the chemistry and on the antioxidant activity of lycopene from dry tomato peel and tomato powder.

    PubMed

    Gámez, M Carmen; Calvo, Marta M; Selgas, M Dolores; García, M Luisa; Erler, Katrin; Böhm, Volker; Catalano, Assunta; Simone, Rossella; Palozza, Paola

    2014-02-19

    Tomato powder (TP) and dry tomato peel (DTP) have been previously used in our laboratory as a source of lycopene to manufacture meat products ready-to-eat (RTE) submitted to E-beam irradiation with good technological and sensory results. Present work describes the studies performed in order to investigate the effect of radiation on chemical changes and antioxidant properties of lycopene. DTP and TP were irradiated (4 kGy). Changes on lycopene were analyzed by HPLC; inhibition of reactive oxygen species (ROS), possible modulation of mitogen-activated protein kinases (MAPK) cascade, nuclear factor κ-light-chain-enhancer of activated B cells (NP-κB) activation and expression of proteins involved in oxidation stress were analyzed in RAT-1 fibroblasts cell culture. Radiation reduced the content of all-E-lycopene and increased (Z)-lycopene, lycopene isomerization, and degradation being higher in DTP than in TP. E-Beam treatment increased the antioxidant ability of both DTP and TP in inhibiting spontaneous and H2O2-induced oxidative stress in cultured fibroblasts. Antioxidant activity was higher in DTP than in TP samples. PMID:24475969

  6. Aerodynamic drag reduction tests on a full-scale tractor-trailer combination with several add-on devices

    NASA Technical Reports Server (NTRS)

    Montoya, L. C.; Steers, L. L.

    1974-01-01

    Aerodynamic drag tests were performed on a conventional cab-over-engine tractor with a 45-foot trailer and five commercially available or potentially available add-on devices using the coast-down method. The tests ranged in velocity from approximately 30 miles per hour to 65 miles per hour and included some flow visualization. A smooth, level runway at Edwards Air Force Base was used for the tests, and deceleration measurements were taken with both accelerometers and stopwatches. An evaluation of the drag reduction results obtained with each of the five add-on devices is presented.

  7. A numerical study of scale effects on performance of a tractor type podded propeller

    NASA Astrophysics Data System (ADS)

    Choi, Jung-Kyu; Park, Hyoung-Gil; Kim, Hyoung-Tae

    2014-06-01

    In this study, the scale effect on the performance of the podded propeller of tractor type is investigated. Turbulent flow computations are carried out for Reynolds numbers increasing progressively from model scale to full scale using the CFD analysis. The result of the flow calculation for model scale Reynolds numbers agrees well with that of the experiment of a large cavitation tunnel. The existing numerical analysis indicates that the performance of the podded propeller blades is mainly influenced by the advance coefficient and relatively little by the Reynolds number. However, the drag of pod housing with propeller in operation is different from that of pod housing without propeller due to the acceleration and swirl of propeller slipstream which is altered by propeller loading as well as the pressure recovery and friction according to Reynolds number, which suggests that the pod housing drag under the condition of propeller in operation is the key factor of the scale effect on the performance between model and full scale podded propellers. The so called `drag ratio', which is the ratio of pod housing drag to total thrust of podded propeller, increases as the advance coefficient increases due to accelerated flow in the slipstream of the podded propeller. However, the increasing rate of the drag ratio reduces continuously as the Reynolds number increases from model to full scale progressively. The contribution of hydrodynamic forces, which acts on the parts composed of the pod housing with propeller operating in various loading conditions, to the thrust and the torque of the total propeller unit are presented for a range of Reynolds numbers from model to full scales.

  8. NEW ACTIVE MEDIA AND ELEMENTS OF LASER SYSTEMS: Simulation of Fresnel diffraction of output beams of unstable resonators

    NASA Astrophysics Data System (ADS)

    Cherepenin, N. D.; Usanov, Yu Ya

    1987-11-01

    The solution is given of the problem of diffraction of a spherical wave by an aperture in the form of a doubly connected region with a rectangular or circular contour, followed by the propagation of this wave across an optical system characterized by an arbitrary ray matrix. The exact expression is obtained for the Fresnel-Kirchhoff integral in terms of Fresnel integrals or Lommel functions of two variables. An investigation is made of the evolution of the effective beam width when its effective length and the shape of the aperture altered. A simple method is proposed for applying this solution in approximate simulation of the distribution of the field in laser output beams generated in unstable optical resonators.

  9. A novel approach to prepare optically active ion doped luminescent materials via electron beam evaporation into ionic liquids

    SciTech Connect

    Richter, K.; Lorbeer, C.; Mudring, A. -V.

    2014-11-10

    A novel approach to prepare luminescent materials via electron-beam evaporation into ionic liquids is presented which even allows doping of host lattices with ions that have a strong size mismatch. Thus, to prove this, MgF2 nanoparticles doped with Eu3+ were fabricated. The obtained nanoparticles featured an unusually high luminescence lifetime and the obtained material showed a high potential for application.

  10. A novel approach to prepare optically active ion doped luminescent materials via electron beam evaporation into ionic liquids

    DOE PAGES

    Richter, K.; Lorbeer, C.; Mudring, A. -V.

    2014-11-10

    A novel approach to prepare luminescent materials via electron-beam evaporation into ionic liquids is presented which even allows doping of host lattices with ions that have a strong size mismatch. Thus, to prove this, MgF2 nanoparticles doped with Eu3+ were fabricated. The obtained nanoparticles featured an unusually high luminescence lifetime and the obtained material showed a high potential for application.

  11. Features of molecular beam epitaxy of the GaN (0001) and GaN (0001-bar) layers with the use of different methods of activation of nitrogen

    SciTech Connect

    Mizerov, A. M. Jmerik, V. N.; Kaibyshev, V. K.; Komissarova, T. A.; Masalov, S. A.; Ivanov, S. V.

    2009-08-15

    The results of comparative studies of the growth kinetics of the GaN layers of different polarity during ammonia molecular beam epitaxy and plasma-assisted molecular beam epitaxy (PA MBE) of nitrogen with the use of sapphire substrates and GaN(0001-bar)/c-Al{sub 2}O{sub 3} templates grown by gas-phase epitaxy from metalorganic compounds are presented. The possibility is shown of obtaining the GaN layers with an atomically smooth surface during molecular beam epitaxy with plasma activation of nitrogen. For this purpose, it is suggested to carry out the growth in conditions enriched with metal near the mode of formation of the Ga drops at a temperature close to the decomposition temperature of GaN (TS {approx} 760 deg. C). The conclusion is made that an increase in the growth temperature positively affects the structural, optical, and electrical properties of the GaN (0001-bar) layers. A high quality of the GaN (0001) films grown by the PA MBE method at a low temperature of {approx}700 deg. C on the GaN/c-Al{sub 2}O{sub 3} templates is shown.

  12. Diagnostic beam absorber in Mu2e beam line

    SciTech Connect

    Rakhno, Igor; /Fermilab

    2011-03-01

    Star density, hadron flux, and residual dose distributions are calculated around the {mu}2e diagnostic beam absorber. Corresponding surface and ground water activation, and air activation are presented as well.

  13. Production of medical radioisotopes with high specific activity in photonuclear reactions with γ-beams of high intensity and large brilliance

    NASA Astrophysics Data System (ADS)

    Habs, D.; Köster, U.

    2011-05-01

    We study the production of radioisotopes for nuclear medicine in ( γ, xn+ yp) photonuclear reactions or ( γ, γ') photoexcitation reactions with high-flux [(1013-1015) γ/s], small diameter ˜(100 μm)2 and small bandwidth (Δ E/ E≈10-3-10-4) γ beams produced by Compton back-scattering of laser light from relativistic brilliant electron beams. We compare them to (ion, xn+ yp) reactions with (ion = p,d, α) from particle accelerators like cyclotrons and (n, γ) or (n,f) reactions from nuclear reactors. For photonuclear reactions with a narrow γ-beam the energy deposition in the target can be managed by using a stack of thin target foils or wires, hence avoiding direct stopping of the Compton and pair electrons (positrons). However, for ions with a strong atomic stopping only a fraction of less than 10-2 leads to nuclear reactions resulting in a target heating, which is at least 105 times larger per produced radioactive ion and often limits the achievable activity. In photonuclear reactions the well defined initial excitation energy of the compound nucleus leads to a small number of reaction channels and enables new combinations of target isotope and final radioisotope. The narrow bandwidth γ excitation may make use of the fine structure of the Pygmy Dipole Resonance (PDR) or fluctuations in γ-width leading to increased cross sections. Within a rather short period compared to the isotopic half-life, a target area of the order of (100 μm)2 can be highly transmuted, resulting in a very high specific activity. ( γ, γ') isomer production via specially selected γ cascades allows to produce high specific activity in multiple excitations, where no back-pumping of the isomer to the ground state occurs. We discuss in detail many specific radioisotopes for diagnostics and therapy applications. Photonuclear reactions with γ-beams allow to produce certain radioisotopes, e.g. 47Sc, 44Ti, 67Cu, 103Pd, 117 m Sn, 169Er, 195 m Pt or 225Ac, with higher specific activity

  14. Development of activity pencil beam algorithm using measured distribution data of positron emitter nuclei generated by proton irradiation of targets containing {sup 12}C, {sup 16}O, and {sup 40}Ca nuclei in preparation of clinical application

    SciTech Connect

    Miyatake, Aya; Nishio, Teiji; Ogino, Takashi

    2011-10-15

    Purpose: The purpose of this study is to develop a new calculation algorithm that is satisfactory in terms of the requirements for both accuracy and calculation time for a simulation of imaging of the proton-irradiated volume in a patient body in clinical proton therapy. Methods: The activity pencil beam algorithm (APB algorithm), which is a new technique to apply the pencil beam algorithm generally used for proton dose calculations in proton therapy to the calculation of activity distributions, was developed as a calculation algorithm of the activity distributions formed by positron emitter nuclei generated from target nuclear fragment reactions. In the APB algorithm, activity distributions are calculated using an activity pencil beam kernel. In addition, the activity pencil beam kernel is constructed using measured activity distributions in the depth direction and calculations in the lateral direction. {sup 12}C, {sup 16}O, and {sup 40}Ca nuclei were determined as the major target nuclei that constitute a human body that are of relevance for calculation of activity distributions. In this study, ''virtual positron emitter nuclei'' was defined as the integral yield of various positron emitter nuclei generated from each target nucleus by target nuclear fragment reactions with irradiated proton beam. Compounds, namely, polyethylene, water (including some gelatin) and calcium oxide, which contain plenty of the target nuclei, were irradiated using a proton beam. In addition, depth activity distributions of virtual positron emitter nuclei generated in each compound from target nuclear fragment reactions were measured using a beam ON-LINE PET system mounted a rotating gantry port (BOLPs-RGp). The measured activity distributions depend on depth or, in other words, energy. The irradiated proton beam energies were 138, 179, and 223 MeV, and measurement time was about 5 h until the measured activity reached the background level. Furthermore, the activity pencil beam data

  15. Introduction to Ion Beam Therapy

    SciTech Connect

    Martisikova, Maria

    2010-01-05

    Presently, ion beam therapy reaches an increasing interest within the field of radiation therapy, which is caused by the promising clinical results obtained in the last decades. Ion beams enable higher dose conformation to the tumor and increased sparing of the surrounding tissue in comparison to the standard therapy using high energy photons. Heavy ions, like carbon, offer in addition increased biological effectiveness, which makes them suitable for treatment of radioresistant tumors. This contribution gives an overview over the physical and biological properties of ion beams. Common fundamental principles of ion beam therapy are summarized and differences between standard therapy with high energy photons, proton and carbon ion therapy are discussed. The technologies used for the beam production and delivery are introduced, with emphasis to the differences between passive and active beam delivery systems. The last part concentrates on the quality assurance in ion therapy. Specialties of dosimetry in medical ion beams are discussed.

  16. Beam tuning

    SciTech Connect

    Pardo, R.C.; Zinkann, G.P.

    1995-08-01

    A program for configuring the linac, based on previously run configurations for any desired beam was used during the past year. This program uses only a small number of empirical tunes to scale resonator fields to properly accelerate a beam with a different charge-to-mass (q/A) ratio from the original tune configuration. The program worked very well for the PII linac section where we can easily match a new beam`s arrival phase and velocity to the tuned value. It was also fairly successful for the Booster and ATLAS sections of the linac, but not as successful as for the PII linac. Most of the problems are associated with setting the beam arrival time correctly for each major linac section. This problem is being addressed with the development of the capacitive pickup beam phase monitor discussed above. During the next year we expect to improve our ability to quickly configure the linac for new beams and reduce the time required for linac tuning. Already the time required for linac tuning as a percentage of research hours has decreased from 22% in FY 1993 to 15% in the first quarter of FY 1995.

  17. Activity of antibodies against Salmonella dublin, Toxoplasma gondii, or Actinobacillus pleuropneumoniae in sera after treatment with electron beam irradiation or binary ethylenimine.

    PubMed Central

    Kyvsgaard, N C; Lind, P; Preuss, T; Kamstrup, S; Lei, J C; Bøgh, H O; Nansen, P

    1996-01-01

    Viral contamination of biological material may constitute a risk when samples are exchanged between countries, and it may be necessary to subject the material to an inactivation treatment. The present study investigated possible adverse effects on antibody activity subsequent to either electron beam irradiation or binary ethylenimine (BEI) treatment. The treatments were performed with sera obtained from pigs or cattle. For each treatment level, the posttreatment activity was plotted against the pretreatment activity, and regression analyses were carried out. The slope of the regression line was used as an estimate for the relative posttreatment activity. For a Toxoplasma gondii indirect enzyme-linked immunosorbent assay (ELISA) and agglutination assay as well as for a Salmonella dublin indirect ELISA, the posttreatment activity was more than 89% of the pretreatment activity when the samples were irradiated in the frozen state (on dry ice) with up to 46. kGy or when they were treated with 5 or 10 mM BEI for up to 48 h. The samples were more sensitive to irradiation in the liquid state. Thus, samples irradiated with 22.6 kGy retained 98% of their activity in the indirect ELISA when they were irradiated in the frozen state on dry ice but only 35% of their activity when they were irradiated in the liquid state at 0 degrees C. The patterns seen in an S. dublin blocking ELISA and an Actinobacillus pleuropneumoniae complement fixation assay differed in that samples with a low level of pretreatment activity were subject to a relatively greater decrease in activity than samples with a high level of pretreatment activity. The complement fixation assay was particularly sensitive to irradiation of serum. It is concluded that serum samples retain sufficient activity by both methods of virus inactivation, especially when used in indirect ELISA or in the T. gondii agglutination assay. PMID:8914750

  18. Energy release, beam attenuation radiation damage, gas production and accumulation of long-lived activity in Pb, Pb-Bi and Hg targets

    SciTech Connect

    Shubin, Yu.N.

    1996-06-01

    The calculation and analysis of the nuclei concentrations and long-lived residual radioactivity accumulated in Pb, Pb-Bi and Hg targets irradiated by 800 MeV, 30 mA proton beam have been performed. The dominating components to the total radioactivity of radionuclides resulting from fission and spallation reactions and radiative capture by both target nuclei and accumulated radioactive nuclei for various irradiation and cooling times were analyzed. The estimations of spectral component contributions of neutron and proton fluxes to the accumulated activity were carried out. The contributions of fission products to the targets activity and partial activities of main long-lived fission products to the targets activity and partial activities of main long-lived fission products were evaluated. The accumulation of Po isotopes due to reactions induced by secondary alpha-particles were found to be important for the Pb target as compared with two-step radiative capture. The production of Tritium in the targets and its contribution to the total targets activity was considered in detail. It is found that total activities of both targets are close to one another.

  19. Tests of Nacelle-Propeller Combinations in Various Positions with Reference to Wings V : Clark Y Biplane Cellule - NACA Cowled Nacelle - Tractor Propeller

    NASA Technical Reports Server (NTRS)

    Valentine, E Floyd

    1935-01-01

    This report is the fifth of a series giving the results obtained from wind tunnel tests on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. This report gives results of tests of an NACA cowled air-cooled engine nacelle with tractor propeller located in 12 positions with reference to a Clark Y biplane cellule.

  20. Tractor-Maintenance: Operation & Daily Care [and] Servicing Air Cleaner & Lubrication. Student Materials. V. A. III. [V-C-1 through V-C-4].

    ERIC Educational Resources Information Center

    Texas A and M Univ., College Station. Vocational Instructional Services.

    Designed for use by students in vocational agricultural classes, this manual deals with tractor maintenance. Operation and daily care are the topics of the first section. Safety is also covered. In the final part of the manual, servicing the air cleaner and lubricating the engine are discussed. Both sections conclude with a quiz. (PLB)

  1. Modeling and stabilization results for a charge or current-actuated active constrained layer (ACL) beam model with the electrostatic assumption

    NASA Astrophysics Data System (ADS)

    Özer, Ahmet Özkan

    2016-04-01

    An infinite dimensional model for a three-layer active constrained layer (ACL) beam model, consisting of a piezoelectric elastic layer at the top and an elastic host layer at the bottom constraining a viscoelastic layer in the middle, is obtained for clamped-free boundary conditions by using a thorough variational approach. The Rao-Nakra thin compliant layer approximation is adopted to model the sandwich structure, and the electrostatic approach (magnetic effects are ignored) is assumed for the piezoelectric layer. Instead of the voltage actuation of the piezoelectric layer, the piezoelectric layer is proposed to be activated by a charge (or current) source. We show that, the closed-loop system with all mechanical feedback is shown to be uniformly exponentially stable. Our result is the outcome of the compact perturbation argument and a unique continuation result for the spectral problem which relies on the multipliers method. Finally, the modeling methodology of the paper is generalized to the multilayer ACL beams, and the uniform exponential stabilizability result is established analogously.

  2. Beam-beam deflection and signature curves for elliptic beams

    SciTech Connect

    Ziemann, V.

    1990-10-22

    In this note we will present closed expressions for the beam-beam deflection angle for arbitrary elliptic beams including tilt. From these expressions signature curves, i.e., systematic deviations from the round beam deflection curve due to ellipticity or tilt are derived. In the course of the presentation we will prove that it is generally impossible to infer individual beam sizes from beam-beam deflection scans. 3 refs., 2 figs.

  3. Edible flowers of Viola tricolor L. as a new functional food: antioxidant activity, individual phenolics and effects of gamma and electron-beam irradiation.

    PubMed

    Koike, Amanda; Barreira, João C M; Barros, Lillian; Santos-Buelga, Celestino; Villavicencio, Anna L C H; Ferreira, Isabel C F R

    2015-07-15

    Edible flowers are used in food preparations, being also recognized for their beneficial effects on human health. Nevertheless, these species are highly perishable, and irradiation treatment might be applied to ensure food quality and increase their shelf life. Viola tricolor L. is a typical edible flower, with multiple applications and biological properties, mainly provided by the flavonoid content. In the present work, the phenolic compounds were analyzed by HPLC-DAD-ESI/MS, and the antioxidant activity was evaluated using biochemical assays. Linear discriminant analyses (LDA) were performed in order to compare the results obtained with flowers submitted to different irradiation doses and technologies (cobalt-60 and electron-beam). In general, irradiated samples (mostly with 1 kGy) showed the highest phenolic content and antioxidant activity. Furthermore, the significant differences observed in the LDA allow determination of which dose and/or technology is suitable to obtain flowers with higher antioxidant potential.

  4. A new experiment to investigate the origin of optical activity using a low energy positron beam of controlled helicity. [molecular biology

    NASA Technical Reports Server (NTRS)

    Gidley, D. W.; Rich, A.; Van House, J. C.; Zitzewitz, P. W.

    1981-01-01

    Previous experiments undertaken in search of a correlation between the origin of optical activity in biological molecules and the helicity of beta particles emitted in nuclear beta decay have not provided any useful results. A description is presented of an experiment in which a low energy polarized positron beam of controlled helicity interacts with an optically active material to form positronium in vacuum. Advantages of the current study compared to the previous experiments are mainly related to a much greater sensitivity. Initially, it will be possible to detect a helicity-dependent asymmetry in triplet positronium formation of 1 part in 10,000. Improvements to better than 1 part in 100,000 should be attainable.

  5. A method for measuring tissue-equivalent dose using a pin diode and activation foil in epithermal neutron beams with EN < 100 keV.

    PubMed

    Carolan, Martin G; Rosenfeld, Anatoly B

    2006-01-01

    Silicon (Si) pin diodes can be used for neutron dosimetry by observing the change in forward bias voltage caused by neutron induced displacement damage in the diode junction. Pin diode energy response depends on Si displacement damage KERMA (K(Si)). It is hypothesised that tissue-equivalent (TE) neutron dose could be expressed as a linear combination of K(Si) and foil activation terms. Monte Carlo simulations (MCNP) of parallel monoenergetic neutron beams incident on a cylindrical TE phantom were used to calculate TE dose, K(Si) and Au, Cu and Mn foil activations along the central axis of the phantom. For spectra with neutron energies <100 keV, it is possible to estimate the TE kerma based on silicon damage kerma and Cu or Mn foil measurements. More accurate estimates are possible for spectra where the maximum neutron energy does not exceed 30 keV. PMID:16644975

  6. Method of achieving ultra-wideband true-time-delay beam steering for active electronically scanned arrays

    DOEpatents

    Loui, Hung; Brock, Billy C.

    2016-10-25

    The various embodiments presented herein relate to beam steering an array antenna by modifying intermediate frequency (IF) waveforms prior to conversion to RF signals. For each channel, a direct digital synthesis (DDS) component can be utilized to generate a waveform or modify amplitude, timing and phase of a waveform relative to another waveform, whereby the generation/modification can be performed prior to the IF input port of a mixer on each channel. A local oscillator (LO) signal can be utilized to commonly drive each of the mixers. After conversion at the RF output port of each of the mixers, each RF signal can be transmitted by a respective antenna element in the antenna array. Initiation of transmission of each RF signal can be performed simultaneously at each antenna. The process can be reversed during receive whereby timing, amplitude, and phase of the received can be modified digitally post ADC conversion.

  7. Caution -- Beam Crossing Ahead

    SciTech Connect

    Barat, Kenneth L.

    2008-04-02

    There are times when a laser beam needs to cross between tables or even go from one room to another. This presents an interesting traffic-flow and safety challenge to both the laser safety officer and laser user. Fortunately it is a challenge that has several solutions But the simplest solution may not be the best one. For example, the simplest way to get a beam from one optical table to another is just to put a sturdy tube around it. That's a permanent solution, and it completely contains the laser beam. While this is laser safe, there can be egress issues if it blocks a walkway. One comment this author often hears is, 'We can just duck under the tube.' The fire marshal, as well as the laser safety officer, might have issues with this. Especially in the case of a darkened lab, a blocked walkway can present a hazard of its own. One good solution is to transport the beam from Point A to Point B through a fiberoptic cable, when that is possible. One should easily be able to run the fiber up and over any walkway or down through a conduit on the floor. An important concern often overlooked with fibers is a label at the termination end indicating disconnection may expose one to laser radiation. Suppose there's an experiment that is usually confined to a single optical table, but sometimes needs to expand to a second table. It's inconvenient to install a permanent tube between the tables, so some sort of temporary arrangement is desirable. I have often seen people casually lay a beam tube across support arms, and remove it when it's not needed. The problem with this approach is that there's no mechanism to prevent the beam from crossing if somebody's forgotten the tube, or if the tube gets knocked out of place. A better solution is a mechanism that only allows the beam to cross when the beam protection is in place. A swing shutter, or a guillotine and swing arm, are examples (Figures 1 and 2). Another alternative is a sensor, maybe a little microswitch, that activates a

  8. Charge-exchange measurements of MHD activity during neutral beam injection in the Princeton Large Torus and the Poloidal Divertor Experiment

    SciTech Connect

    Goldston, R.J.; Kaita, R.; Beiersdorfer, P.; Gammel, G.; Herndon, D.L.; McCune, D.C.; Meyerhofer, D.D.

    1986-07-01

    The horizontally scanning, multiangle charge-exchange analyzers on the Princeton Large Torus (PLT) and the Poloidal Divertor Experiment (PDX) were used to study the effects of MHD activity on the background ion distribution function and on the beam ion slowing-down process during high-power neutral injection. Sawtooth oscillations were observed in the fast ion flux on PLT and PDX, and measurements with neutral beams providing local neutral density enhancement indicate that ions are transported radially when these events occur. With near-perpendicular injection in PDX, at the lower toroidal fields necessary to maximize beta, rapid, repetitive bursts of greatly enhanced charge-exchange flux were observed. These are associated with the ''fishbone'' MHD instability, and a substantial depletion of the perpendicular slowing-down spectrum below the injection energy was seen. A simple phenomenological model for this loss mechanism was developed, and its use in simulation codes has been successful in providing good agreement with the data. The behavior and characteristics of this model are well matched by the direct theoretical calculations.

  9. Beam loss

    NASA Astrophysics Data System (ADS)

    VanGinneken, A.; Edwards, D.; Harrison, M.

    1989-04-01

    This paper presents results from simulations of beam losses during the operation of a superconducting accelerator. The calculations use a combination of hadron/electromagnetic cascade plus elastic scattering codes with accelerator tracking routines. These calculations have been used in conjunction with the design of the Fermilab Tevatron. First accelerator geometry is described. The rest of the paper discusses a detailed attempt to simulate a fast extraction cycle, essentially in chronological order. Beginning with an unperturbed beam, the simulation generates proton phase-space distributions incident on the electrostatic septum. These interact either elastically or inelastically with the septum wires, and the products of these interactions are traced through the machine. Where these leave the accelerator, energy deposition levels in the magnets are calculated together with the projected response of the beam-loss monitors in this region. Finally, results of the calculation are compared with experimental data. (AIP)

  10. Reduced Pressure Electron Beam Welding Evaluation Activities on a Ni-Cr-Mo Alloy for Nuclear Waste Packages

    SciTech Connect

    Wong, F; Punshon, C; Dorsch, T; Fielding, P; Richard, D; Yang, N; Hill, M; DeWald, A; Rebak, R; Day, S; Wong, L; Torres, S; McGregor, M; Hackel, L; Chen, H-L; Rankin, J

    2003-09-11

    The current waste package design for the proposed repository at Yucca Mountain Nevada, USA, employs gas tungsten arc welding (GTAW) in fabricating the waste packages. While GTAW is widely used in industry for many applications, it requires multiple weld passes. By comparison, single-pass welding methods inherently use lower heat input than multi-pass welding methods which results in lower levels of weld distortion and also narrower regions of residual stresses at the weld TWI Ltd. has developed a Reduced Pressure Electron Beam (RPEB) welding process which allows EB welding in a reduced pressure environment ({le} 1 mbar). As it is a single-pass welding technique, use of RPEB welding could (1) achieve a comparable or better materials performance and (2) lead to potential cost savings in the waste package manufacturing as compared to GTAW. Results will be presented on the initial evaluation of the RPEB welding on a Ni-Cr-Mo alloy (a candidate alloy for the Yucca Mountain waste packages) in the areas of (a) design and manufacturing simplifications, (b) material performance and (c) weld reliability.

  11. GPU accelerated fully space and time resolved numerical simulations of self-focusing laser beams in SBS-active media

    SciTech Connect

    Mauger, Sarah; Colin de Verdière, Guillaume; Bergé, Luc; Skupin, Stefan

    2013-02-15

    A computer cluster equipped with Graphics Processing Units (GPUs) is used for simulating nonlinear optical wave packets undergoing Kerr self-focusing and stimulated Brillouin scattering in fused silica. We first recall the model equations in full (3+1) dimensions. These consist of two coupled nonlinear Schrödinger equations for counterpropagating optical beams closed with a source equation for light-induced acoustic waves seeded by thermal noise. Compared with simulations on a conventional cluster of Central Processing Units (CPUs), GPU-based computations allow us to use a significant (16 times) larger number of mesh points within similar computation times. Reciprocally, simulations employing the same number of mesh points are between 3 and 20 times faster on GPUs than on the same number of classical CPUs. Performance speedups close to 45 are reported for isolated functions evaluating, e.g., the optical nonlinearities. Since the field intensities may reach the ionization threshold of silica, the action of a defocusing electron plasma is also addressed.

  12. Characterisation of optimal human driver model and stability of a tractor-semitrailer vehicle system with time delay

    NASA Astrophysics Data System (ADS)

    Liu, Zhaoheng

    2007-07-01

    In this paper, a vehicle/driver close-loop system is studied in order to characterise the inherent model parameters of an optimal human controller for a regulation task (e.g. stabilisation after a wind gust) in articulated vehicle motions. The tractor-semitrailer vehicle model consists of two articulated rigid bodies moving on a horizontal plane with a constant forward speed. The driver establishes his steering control through a time-delayed feedback from current vehicle states with respect to the desired motion. Identification of driver model parameters is achieved through an optimal control approach. The stability of the delayed dynamical system is also studied using a numerical method by computing the eigenvalues near the imaginary axis.

  13. Relative safety of traditional agricultural tractor power take-off (PTO) drivelines compared to fluid power--a review.

    PubMed

    Thomas, R S; Buckmaster, D R

    2003-08-01

    Nearly all tractor PTO arrangements used today consist of a rotating mechanical shaft with two or more universal joints and splined couplings. Although this method of power transfer has been the standard for decades, it continues to be a hazard to farm workers. Commonly, PTO accidents involve the snagging of clothes, resulting in the victim being rapidly and violently drawn into (and around) the rotating shaft. Entanglement injuries are both common and severe in the agricultural workforce, with poor shielding maintenance as a contributing factor. If PTO loads were driven with fluid power, this entanglement hazard would be eliminated. With high-pressure injection injury being the principal hazard, the fluid power alternative appears to pose a lower risk in terms of both frequency of occurrence and severity of injury. PMID:12970954

  14. Interplay between cellular activity and three-dimensional scaffold-cell constructs with different foam structure processed by electron beam melting.

    PubMed

    Nune, Krishna C; Misra, R Devesh K; Gaytan, Sara M; Murr, Lawrence E

    2015-05-01

    The cellular activity, biological response, and consequent integration of scaffold-cell construct in the physiological system are governed by the ability of cells to adhere, proliferate, and biomineralize. In this regard, we combine cellular biology and materials science and engineering to fundamentally elucidate the interplay between cellular activity and interconnected three-dimensional foamed architecture obtained by a novel process of electron beam melting and computational tools. Furthermore, the organization of key proteins, notably, actin, vinclulin, and fibronectin, involved in cellular activity and biological functions and relationship with the structure was explored. The interconnected foamed structure with ligaments was favorable to cellular activity that includes cell attachment, proliferation, and differentiation. The primary rationale for favorable modulation of cellular functions is that the foamed structure provided a channel for migration and communication between cells leading to highly mineralized extracellular matrix (ECM) by the differentiating osteoblasts. The filopodial interaction amongst cells on the ligaments was a governing factor in the secretion of ECM, with consequent influence on maturation and mineralization.

  15. An approach for modeling the influence of wheel tractor loads and vibration frequencies on soil compaction

    NASA Astrophysics Data System (ADS)

    Verotti, M.; Servadio, P.; Belfiore, N. P.; Bergonzoli, S.

    2012-04-01

    Both soil compaction and ground vibration are forms of environmental degradation that may be understood in the context of the vehicle-soil interaction process considered (Hildebrand et al., 2008). The transit of tractors on agricultural soil is often the main cause of soil compaction increasing. As known, this can be a serious problems for tillage and sowing and therefore the influence of all the affecting factors have been extensively studied in the last decades in order to understand their impact on the biosystem. There are factors related to the climate, namely to the rainfalls and temperature, and many others. Hence, it is not simple to figure out a complete model for predicting an index of compaction, for a given situation. Soil compaction models are important tools for controlling soil compaction due to agricultural field traffic and they are potentially useful technique to provide information concerning correct soil management. By means of such models, strategies and recommendations for prevention of soil compaction may be developed and specific advice may be given to farmers and advisers. In order to predict field wheeled and tracked vehicle performance, some empirical methods, used for off-road vehicle, were applied by Servadio (2010) on agricultural soil. The empirical indexes included, besides the soil strength, the load carried by the tire or track, some technical characteristics of the tire or track of the vehicle (tire or track width, tire or track wheel diameter, unloaded tire section height, number of wheel station in one track, tire deflection, total length of the belt track, the track pitch) as well as the vehicle passes. They have been validated with the tests results of agricultural vehicles over a range of soil in central Italy. Among the parameters which affect soil compaction, the water content of the soil, the axle load and number of vehicle passes proved to be the most important ones. The present paper concerns mainly vehicle

  16. Center for Beam Physics, 1992

    SciTech Connect

    Not Available

    1993-06-01

    This report contains the following information on the center for beam physics: Facilities; Organizational Chart; Roster; Profiles of Staff; Affiliates; Center Publications (1991--1993); and 1992 Summary of Activities.

  17. The Fermilab neutrino beam program

    SciTech Connect

    Rameika, Regina A.; /Fermilab

    2007-01-01

    This talk presents an overview of the Fermilab Neutrino Beam Program. Results from completed experiments as well as the status and outlook for current experiments is given. Emphasis is given to current activities towards planning for a future program.

  18. 100-MeV proton beam intensity measurement by Au activation analysis using 197Au(p, pn)196Au and 197Au(p, p3n)194Au reactions

    NASA Astrophysics Data System (ADS)

    Mokhtari Oranj, Leila; Jung, Nam-Suk; Oh, Joo-Hee; Lee, Hee-Seock

    2016-05-01

    The proton beam intensity of a 100-MeV proton linac at the Korea Multi-purpose Accelerator Complex (KOMAC) was measured by an Au activation analysis using 197Au(p, pn)196Au and 197Au(p, p3n)194Au reactions to determine the accuracy and precision of beam intensity measurement using Gafchromic film dosimetry method. The target, irradiated by 100-MeV protons, was arranged in a stack consisting of Au, Al foils and Pb plates. The yields of produced radio-nuclei in Au foils were obtained by gamma-ray spectroscopy. The FLUKA code was employed to calculate the energy spectrum of protons onto the front surface of Au foils located at three different depth points of the target and also to investigate the condition of incident beam on the target. A good agreement was found between the beam intensity measurements using the activation analysis method at three different depth points of the target. An excellent agreement was also observed between the beam intensity measurements using the Au activation analysis method and the dosimetry method using Gafchromic film.

  19. Tests of Nacelle-Propeller Combinations in Various Positions with Reference to Wings III : Clark Y Wing - Various Radial-engine Cowlings - Tractor Propeller

    NASA Technical Reports Server (NTRS)

    Wood, Donald H

    1933-01-01

    This report is the third of a series giving the results obtained in the 20-foot wind tunnel on the interference drag, and propulsive efficiency of nacelle-propeller-wing combinations. The first report gave the results of the tests of an NACA cowled air-cooled engine nacelle with tractor propeller located in 21 positions with reference to a thick wing. The second report gave the results for several engine cowlings and nacelles with tractor propeller located in four positions with reference to same wing. The present report gives results of tests of the same nacelles and cowlings in the same positions with reference to a smaller wing of Clark y section. The lift, drag, and propulsive efficiency were determined at several angles of attack for each cowling and in each nacelle location.

  20. External Beam Therapy (EBT)

    MedlinePlus

    ... Physician Resources Professions Site Index A-Z External Beam Therapy (EBT) External beam therapy (EBT) is a ... follow-up should I expect? What is external beam therapy and how is it used? External beam ...

  1. TPX/TFTR Neutral Beam energy absorbers

    SciTech Connect

    Dahlgren, F.; Wright, K.; Kamperschroer, J.; Grisham, L.; Lontai, L.; Peters, C.; VonHalle, A.

    1993-11-01

    The present beam energy absorbing surfaces on the TFTR Neutral Beams such as Ion Dumps, Calorimeters, beam defining apertures, and scrapers, are simple water cooled copper plates which wee designed to absorb (via their thermal inertia) the incident beam power for two seconds with a five minute coal down interval between pulses. These components are not capable of absorbing the anticipated beam power loading for 1000 second TPX pulses and will have to be replaced with an actively cooled design. While several actively cooled energy absorbing designs were considered,, the hypervapotron elements currently being used on the JET beamlines were chosen due to their lower cooling water demands and reliable performance on JET.

  2. CEBAF beam loss accounting

    SciTech Connect

    Ursic, R.; Mahoney, K.; Hovater, C.; Hutton, A.; Sinclair, C.

    1995-12-31

    This paper describes the design and implementation of a beam loss accounting system for the CEBAF electron accelerator. This system samples the beam curent throughout the beam path and measures the beam current accurately. Personnel Safety and Machine Protection systems use this system to turn off the beam when hazardous beam losses occur.

  3. Health risk evaluation of whole-body vibration by ISO 2631-5 and ISO 2631-1 for operators of agricultural tractors and recreational vehicles.

    PubMed

    Park, Min-Soo; Fukuda, Takabumi; Kim, Tae-Gu; Maeda, Setsuo

    2013-01-01

    This paper presents experimental research evaluation of the vibration exposure for the health risk prediction during vehicle operation. The vibration measurements were carried out on a recreational vehicle and two types of agricultural tractors. The vibration levels were measured for different surfaces and vehicle speed conditions. Based on the analysis of the results in the small agricultural tractor operated in the workplace (frameworks), Sed exceeded 0.80 MPa by ISO2631-5:2004, and Av exceeded 0.89 m/s(2) by ISO2631-1:1997. That means that operators driving small agricultural tractors more than 8 h a day have a high probability of adverse health effects. However, the exposure value for the recreational vehicle had Sed < 0.5 MPa by ISO2631-5:2004 and Av < 0.5 m/s(2) by ISO2631-1:1997 on highways and local roads. That means Recreational Vehicle operators driving more than 8 h a day, have a low probability of adverse health effects. Also, for the recreational vehicle, vibration was taken at different speeds (40-60 km/h, 80 km/h, 100-120 km/h). However, the speed change did not appear to affect the vibration dose variation while driving a vehicle on the highway and road. Finally, the health effect index of ISO2631-5:2004 are almost the same as assessment of health effect by ISO2631-1:1997. PMID:23558167

  4. Health risk evaluation of whole-body vibration by ISO 2631-5 and ISO 2631-1 for operators of agricultural tractors and recreational vehicles.

    PubMed

    Park, Min-Soo; Fukuda, Takabumi; Kim, Tae-Gu; Maeda, Setsuo

    2013-01-01

    This paper presents experimental research evaluation of the vibration exposure for the health risk prediction during vehicle operation. The vibration measurements were carried out on a recreational vehicle and two types of agricultural tractors. The vibration levels were measured for different surfaces and vehicle speed conditions. Based on the analysis of the results in the small agricultural tractor operated in the workplace (frameworks), Sed exceeded 0.80 MPa by ISO2631-5:2004, and Av exceeded 0.89 m/s(2) by ISO2631-1:1997. That means that operators driving small agricultural tractors more than 8 h a day have a high probability of adverse health effects. However, the exposure value for the recreational vehicle had Sed < 0.5 MPa by ISO2631-5:2004 and Av < 0.5 m/s(2) by ISO2631-1:1997 on highways and local roads. That means Recreational Vehicle operators driving more than 8 h a day, have a low probability of adverse health effects. Also, for the recreational vehicle, vibration was taken at different speeds (40-60 km/h, 80 km/h, 100-120 km/h). However, the speed change did not appear to affect the vibration dose variation while driving a vehicle on the highway and road. Finally, the health effect index of ISO2631-5:2004 are almost the same as assessment of health effect by ISO2631-1:1997.

  5. EVALUATION OF THE EFFECTIVENESS OF TRUCK EFFICIENCY TECHNOLOGIES IN CLASS 8 TRACTOR-TRAILERS BASED ON A TRACTIVE ENERGY ANALYSIS USING MEASURED DRIVE CYCLE DATA

    SciTech Connect

    LaClair, Tim J; Gao, Zhiming; Fu, Joshua S.; Calcagno, Jimmy; Yun, Jeongran

    2014-01-01

    Quantifying the fuel savings that can be achieved from different truck fuel efficiency technologies for a fleet s specific usage allows the fleet to select the combination of technologies that will yield the greatest operational efficiency and profitability. This paper presents an analysis of vehicle usage in a commercial vehicle fleet and an assessment of advanced efficiency technologies using an analysis of measured drive cycle data for a class 8 regional commercial shipping fleet. Drive cycle measurements during a period of a full year from six tractor-trailers in normal operations in a less-than-truckload (LTL) carrier were analyzed to develop a characteristic drive cycle that is highly representative of the fleet s usage. The vehicle mass was also estimated to account for the variation of loads that the fleet experienced. The drive cycle and mass data were analyzed using a tractive energy analysis to quantify the fuel efficiency and CO2 emissions benefits that can be achieved on class 8 tractor-trailers when using advanced efficiency technologies, either individually or in combination. Although differences exist among class 8 tractor-trailer fleets, this study provides valuable insight into the energy and emissions reduction potential that various technologies can bring in this important trucking application.

  6. Toward automated beam optics control

    SciTech Connect

    Silbar, R.R.; Schultz, D.E.

    1987-01-01

    We have begun a program aiming toward automatic control of charged-particle beam optics using artificial intelligence programming techniques. In developing our prototype, we are working with LISP machines and the KEE expert system shell. Our first goal was to develop a ''mouseable'' representation of a typical beam line. This responds actively to changes entered from the mouse or keyboard, giving an updated display of the beam line itself, its optical properties, and the instrumentation and control devices as seen by the operater. We have incorporated TRANSPORT, written in Fortran but running as a callable procedure in the LISP environment, for simulation of the beam-line optics. This paper describes the experience gained in meeting our first goal and discusses plans to extend the work so that it is usable, in realtime, on an operating beam line. 11 refs.

  7. Beam halo studies in LEHIPA DTL

    NASA Astrophysics Data System (ADS)

    Roy, S.; Pande, R.; Rao, S. V. L. S.; Krishnagopal, S.; Singh, P.

    2015-11-01

    The Low Energy High Intensity Proton Accelerator (LEHIPA) project at Bhabha Atomic Research Centre (BARC) consists of a 20 MeV, 30 mA proton linac. The accelerator comprises of a 3 MeV Radio Frequency Quadrupole (RFQ) and a 20 MeV Drift Tube Linac (DTL). In such high intensity accelerators, beam halos are of concern as they not only cause an increase in emittance, but also lead to beam loss and radio activation. We have studied the effect of beam mismatch at the DTL input on halo formation and propagation. The particle core model is used to excite the three envelope eigen modes; the quadrupole mode, the fast mode and the slow mode by giving input beam mismatch. These modes get damped as the beam progresses through the DTL. The damping mechanism is clearly Landau damping and leads to increase in rms emittance of the beam. The evolution of these modes and the corresponding increase in beam emittance and maximum beam extent, as the beam propagates through the DTL, has been studied for different space charge tunes. The halo parameter based on the definition of Allen and Wangler has been calculated. It is seen that beam halos are very important for LEHIPA DTL, even at 20 MeV and leads to emittance and beam size increase and also to beam loss in some cases. The longitudinal halo is present even without mismatch and transverse halos arise in the presence of beam mismatch.

  8. Beam geometry selection using sequential beam addition

    SciTech Connect

    Popple, Richard A. Brezovich, Ivan A.; Fiveash, John B.

    2014-05-15

    Purpose: The selection of optimal beam geometry has been of interest since the inception of conformal radiotherapy. The authors report on sequential beam addition, a simple beam geometry selection method, for intensity modulated radiation therapy. Methods: The sequential beam addition algorithm (SBA) requires definition of an objective function (score) and a set of candidate beam geometries (pool). In the first iteration, the optimal score is determined for each beam in the pool and the beam with the best score selected. In the next iteration, the optimal score is calculated for each beam remaining in the pool combined with the beam selected in the first iteration, and the best scoring beam is selected. The process is repeated until the desired number of beams is reached. The authors selected three treatment sites, breast, lung, and brain, and determined beam arrangements for up to 11 beams from a pool comprised of 25 equiangular transverse beams. For the brain, arrangements were additionally selected from a pool of 22 noncoplanar beams. Scores were determined for geometries comprised equiangular transverse beams (EQA), as well as two tangential beams for the breast case. Results: In all cases, SBA resulted in scores superior to EQA. The breast case had the strongest dependence on beam geometry, for which only the 7-beam EQA geometry had a score better than the two tangential beams, whereas all SBA geometries with more than two beams were superior. In the lung case, EQA and SBA scores monotonically improved with increasing number of beams; however, SBA required fewer beams to achieve scores equivalent to EQA. For the brain case, SBA with a coplanar pool was equivalent to EQA, while the noncoplanar pool resulted in slightly better scores; however, the dose-volume histograms demonstrated that the differences were not clinically significant. Conclusions: For situations in which beam geometry has a significant effect on the objective function, SBA can identify

  9. Beam-Bem interactions

    SciTech Connect

    Kim, Hyung Jin; /Fermilab

    2011-12-01

    In high energy storage-ring colliders, the nonlinear effect arising from beam-beam interactions is a major source that leads to the emittance growth, the reduction of beam life time, and limits the collider luminosity. In this paper, two models of beam-beam interactions are introduced, which are weak-strong and strong-strong beam-beam interactions. In addition, space-charge model is introduced.

  10. The interaction of C60 on Si(111) 7x7 studied by Supersonic Molecular Beams: interplay between precursor kinetic energy and substrate temperature in surface activated processes.

    NASA Astrophysics Data System (ADS)

    Aversa, Lucrezia; Taioli, Simone; Nardi, Marco; Tatti, Roberta; Verucchi, Roberto; Iannotta, Salvatore

    2015-06-01

    Buckminsterfullerene (C60) is a molecule fully formed of carbon that can be used, owing to its electronic and mechanical properties, as “clean” precursor for the growth of carbon-based materials, ranging from ?-conjugated systems (graphenes) to synthesized species, e.g. carbides such as silicon carbide (SiC). To this goal, C60 cage rupture is the main physical process that triggers material growth. Cage breaking can be obtained either thermally by heating up the substrate to high temperatures (630°C), after C60 physisorption, or kinetically by using Supersonic Molecular Beam Epitaxy (SuMBE) techniques. In this work, aiming at demonstrating the growth of SiC thin films by C60 supersonic beams, we present the experimental investigation of C60 impacts on Si(111) 7x7 kept at 500°C for translational kinetic energies ranging from 18 to 30 eV. The attained kinetically activated synthesis of SiC submonolayer films is probed by in-situ surface electron spectroscopies (XPS and UPS). Furthermore, in these experimental conditions the C60-Si(111) 7×7 collision has been studied by computer simulations based on a tight-binding approximation to Density Functional Theory, DFT. Our theoretical and experimental findings point towards a kinetically driven growth of SiC on Si, where C60 precursor kinetic energy plays a crucial role, while temperature is relevant only after cage rupture to enhance Si and carbon reactivity. In particular, we observe a counterintuitive effect in which for low kinetic energy (below 22 eV), C60 bounces back without breaking more effectively at high temperature due to energy transfer from excited phonons. At higher kinetic energy (22 < K < 30 eV), for which cage rupture occurs, temperature enhances reactivity without playing a major role in the cage break. These results are in good agreement with ab-initio molecular dynamics simulations. SuMBE is thus a technique able to drive materials growth at low temperature regime.

  11. Adenovirus-mediated FIR demonstrated TP53-independent cell-killing effect and enhanced antitumor activity of carbon-ion beams.

    PubMed

    Kano, M; Matsushita, K; Rahmutulla, B; Yamada, S; Shimada, H; Kubo, S; Hiwasa, T; Matsubara, H; Nomura, F

    2016-01-01

    Combination therapy of carbon-ion beam with the far upstream element-binding protein (FBP)-interacting repressor, FIR, which interferes with DNA damage repair proteins, was proposed as an approach for esophageal cancer treatment with low side effects regardless of TP53 status. In vivo therapeutic antitumor efficacy of replication-defective adenovirus (E1 and E3 deleted adenovirus serotype 5) encoding human FIR cDNA (Ad-FIR) was demonstrated in the tumor xenograft model of human esophageal squamous cancer cells, TE-2. Bleomycin (BLM) is an anticancer agent that introduces DNA breaks. The authors reported that Ad-FIR involved in the BLM-induced DNA damage repair response and thus applicable for other DNA damaging agents. To examine the effect of Ad-FIR on DNA damage repair, BLM, X-ray and carbon-ion irradiation were used as DNA damaging agents. The biological effects of high linear energy transfer (LET) radiotherapy used with carbon-ion irradiation are more expansive than low-LET conventional radiotherapy, such as X-rays or γ rays. High LET radiotherapy is suitable for the local control of tumors because of its high relative biological effectiveness. Ad-FIR enhanced BLM-induced DNA damage indicated by γH2AX in vitro. BLM treatment increased endogenous nuclear FIR expression in TE-2 cells, and P27Kip1 expression was suppressed by TP53 siRNA and BLM treatment. Further, Ad-FIRΔexon2, a dominant-negative form of FIR that lacks exon2 transcriptional repression domain, decreased Ku86 expression. The combination of Ad-FIR and BLM in TP53 siRNA increased DNA damage. Additionally, Ad-FIR showed synergistic cell toxicity with X-ray in vitro and significantly increased the antitumor efficacy of carbon-ion irradiation in the xenograft mouse model of TE-2 cells (P=0.03, Mann-Whitney's U-test) and was synergistic with the sensitization enhancement ratio (SER) value of 1.15. Therefore, Ad-FIR increased the cell-killing activity of the carbon-ion beam that avoids late

  12. Neutral Beam Ion Confinement in NSTX

    SciTech Connect

    D.S. Darrow; E.D. Fredrickson; S.M. Kaye; S.S. Medley; and A.L. Roquemore

    2001-07-24

    Neutral-beam (NB) heating in the National Spherical Torus Experiment (NSTX) began in September 2000 using up to 5 MW of 80 keV deuterium (D) beams. An initial assessment of beam ion confinement has been made using neutron detectors, a neutral particle analyzer (NPA), and a Faraday cup beam ion loss probe. Preliminary neutron results indicate that confinement may be roughly classical in quiescent discharges, but the probe measurements do not match a classical loss model. MHD activity, especially reconnection events (REs) causes substantial disturbance of the beam ion population.

  13. New multi-beam bathymetric map of the Ionian Sea (Central Mediterranean): Evidence for active sedimentary and morpho-tectonic processes along the Africa-Eurasia plate boundary

    NASA Astrophysics Data System (ADS)

    Gutscher, M. A.; Kopp, H.; Krastel, S.; Bohrmann, G.; Garlan, T.; Zaragosi, S.; Klaucke, I.; Wintersteller, P.; Loubrieu, B.; Le Faou, Y.; San Pedro, L.; Dominguez, S.; Rovere, M.; Mercier De Lepinay, B. F.

    2015-12-01

    A combined dataset of multi-beam bathymetry, based on 5 recent marine geophysical surveys since 2010 as well as a compilation of earlier surveys, now spans the vast majority of the Ionian Sea and the active margin of East Sicily and Calabria. (The new surveys are: R/V Meteor cruise 86, 2010 PI - S. Krastel; MocoSed R/V PourquoiPas 2012 PI - T. Garlan; Circee R/V Suroit 2013 PI - M.-A. Gutscher; R/V Meteor cruise 111, 2014 PI's - H. Kopp, M.-A. Gutscher; R/V Meteor cruise 112, 2014 PI - G. Bohrmann). This new compilation of mostly unpublished bathymetric data is presented as a 2 arc-sec (60m) grid and reveals fine-scale structures on the seafloor in unprecedented detail. These include the deeply incised Malta-Hyblean Escarpment, numerous submarine canyons, broad regions of relatively flat seafloor dominated by fields of sediment waves, the gently undulating anticlinal fold-and-thrust belts of two accretionary wedge complexes related to the Hellenic subduction (W Mediterranean ridge) and to the Calabrian arc. These accretionary wedges intersect and overlap and define two of the three sides of the triangular Ionian abyssal plain. The internal structure of these morpho-tectonic provinces as well as the transition zones between them is also imaged by high-resolution 72-channel seismic reflection profiles. Together these data offer new insights into the interaction and competition between active sedimentary and tectonic processes shaping this part of the Central Mediterranean. Acknowledgment: The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 603839 (Project ASTARTE - Assessment, Strategy and Risk Reduction for Tsunamis in Europe).

  14. An investigation of drag reduction for tractor trailer vehicles with air deflector and boattail. [wind tunnel tests

    NASA Technical Reports Server (NTRS)

    Muirhead, V. U.

    1981-01-01

    A wind tunnel investigation was conducted to determine the influence of several physical variables on the aerodynamic drag of a trailer model. The physical variables included: a cab mounted wind deflector, boattail on trailer, flow vanes on trailer front, forced transition on trailer, and decreased gap between tractor and trailer. Tests were conducted at yaw angles (relative wind angles) of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 3.58 x 10 to the 5th power 6.12 x 10 to the 5th power based upon the equivalent diameter of the vehicles. The wind deflector on top of the cab produced a calculated reduction in fuel consumption of about 5 percent of the aerodynamic portion of the fuel budget for a wind speed of 15.3 km/hr (9.5 mph) over a wind angle range of 0 deg to 180 deg and for a vehicle speed of 88.5 km/hr (55 mph). The boattail produced a calculated 7 percent to 8 percent reduction in fuel consumption under the same conditions. The decrease in gap reduced the calculated fuel consumption by about 5 percent of the aerodynamic portion of the fuel budget.

  15. Simple beam profile monitor

    SciTech Connect

    Gelbart, W.; Johnson, R. R.; Abeysekera, B.

    2012-12-19

    An inexpensive beam profile monitor is based on the well proven rotating wire method. The monitor can display beam position and shape in real time for particle beams of most energies and beam currents up to 200{mu}A. Beam shape, position cross-section and other parameters are displayed on a computer screen.

  16. Intense low energy positron beams

    SciTech Connect

    Lynn, K.G.; Jacobsen, F.M.

    1993-12-31

    Intense positron beams are under development or being considered at several laboratories. Already today a few accelerator based high intensity, low brightness e{sup +} beams exist producing of the order of 10{sup 8} {minus} 10{sup 9} e{sup +}/sec. Several laboratories are aiming at high intensity, high brightness e{sup +} beams with intensities greater than 10{sup 9} e{sup +}/sec and current densities of the order of 10{sup 13} {minus} 10{sup 14} e{sup +} sec{sup {minus}} {sup 1}cm{sup {minus}2}. Intense e{sup +} beams can be realized in two ways (or in a combination thereof) either through a development of more efficient B{sup +} moderators or by increasing the available activity of B{sup +} particles. In this review we shall mainly concentrate on the latter approach. In atomic physics the main trust for these developments is to be able to measure differential and high energy cross-sections in e{sup +} collisions with atoms and molecules. Within solid state physics high intensity, high brightness e{sup +} beams are in demand in areas such as the re-emission e{sup +} microscope, two dimensional angular correlation of annihilation radiation, low energy e{sup +} diffraction and other fields. Intense e{sup +} beams are also important for the development of positronium beams, as well as exotic experiments such as Bose condensation and Ps liquid studies.

  17. Laser beam monitoring system

    DOEpatents

    Weil, Bradley S.; Wetherington, Jr., Grady R.

    1985-01-01

    Laser beam monitoring systems include laser-transparent plates set at an angle to the laser beam passing therethrough and light sensor for detecting light reflected from an object on which the laser beam impinges.

  18. Relativistic electron beam generator

    DOEpatents

    Mooney, L.J.; Hyatt, H.M.

    1975-11-11

    A relativistic electron beam generator for laser media excitation is described. The device employs a diode type relativistic electron beam source having a cathode shape which provides a rectangular output beam with uniform current density.

  19. A new, simple and precise method for measuring cyclotron proton beam energies using the activity vs. depth profile of zinc-65 in a thick target of stacked copper foils.

    PubMed

    Asad, A H; Chan, S; Cryer, D; Burrage, J W; Siddiqui, S A; Price, R I

    2015-11-01

    The proton beam energy of an isochronous 18MeV cyclotron was determined using a novel version of the stacked copper-foils technique. This simple method used stacked foils of natural copper forming 'thick' targets to produce Zn radioisotopes by the well-documented (p,x) monitor-reactions. Primary beam energy was calculated using the (65)Zn activity vs. depth profile in the target, with the results obtained using (62)Zn and (63)Zn (as comparators) in close agreement. Results from separate measurements using foil thicknesses of 100, 75, 50 or 25µm to form the stacks also concurred closely. Energy was determined by iterative least-squares comparison of the normalized measured activity profile in a target-stack with the equivalent calculated normalized profile, using 'energy' as the regression variable. The technique exploits the uniqueness of the shape of the activity vs. depth profile of the monitor isotope in the target stack for a specified incident energy. The energy using (65)Zn activity profiles and 50-μm foils alone was 18.03±0.02 [SD] MeV (95%CI=17.98-18.08), and 18.06±0.12MeV (95%CI=18.02-18.10; NS) when combining results from all isotopes and foil thicknesses. When the beam energy was re-measured using (65)Zn and 50-μm foils only, following a major upgrade of the ion sources and nonmagnetic beam controls the results were 18.11±0.05MeV (95%CI=18.00-18.23; NS compared with 'before'). Since measurement of only one Zn monitor isotope is required to determine the normalized activity profile this indirect yet precise technique does not require a direct beam-current measurement or a gamma-spectroscopy efficiency calibrated with standard sources, though a characteristic photopeak must be identified. It has some advantages over published methods using the ratio of cross sections of monitor reactions, including the ability to determine energies across a broader range and without need for customized beam degraders. PMID:26226219

  20. Beam imaging sensor

    DOEpatents

    McAninch, Michael D.; Root, Jeffrey J.

    2016-07-05

    The present invention relates generally to the field of sensors for beam imaging and, in particular, to a new and useful beam imaging sensor for use in determining, for example, the power density distribution of a beam including, but not limited to, an electron beam or an ion beam. In one embodiment, the beam imaging sensor of the present invention comprises, among other items, a circumferential slit that is either circular, elliptical or polygonal in nature.

  1. NK Muon Beam

    SciTech Connect

    Koizumi, G.

    1988-09-28

    The NK Muon Beam will be a modified version of the existing NT beam line. The decision to employ a modified version of the NT beam line was made based on considerations of cost and availability of the beam line. Preliminary studies considered use of other beam lines, e.g., the NW beam line, and even of moving the bubble chamber with its superconducting coils but were rejected for reasons such as cost, personnel limitations, and potential conflicts with other users.

  2. Tunable beam displacer

    SciTech Connect

    Salazar-Serrano, Luis José; Valencia, Alejandra; Torres, Juan P.

    2015-03-15

    We report the implementation of a tunable beam displacer, composed of a polarizing beam splitter (PBS) and two mirrors, that divides an initially polarized beam into two parallel beams whose separation can be continuously tuned. The two output beams are linearly polarized with either vertical or horizontal polarization and no optical path difference is introduced between them. The wavelength dependence of the device as well as the maximum separation between the beams achievable is limited mainly by the PBS characteristics.

  3. BEAM INSTRUMENTATION FOR HIGH POWER HADRON BEAMS

    SciTech Connect

    Aleksandrov, Alexander V

    2013-01-01

    This presentation will describe developments in the beam diagnostics which support the understanding and operation of high power hadron accelerators. These include the measurement of large dynamic range transverse and longitudinal beam profiles, beam loss detection, and non-interceptive diagnostics.

  4. Propagation-invariant beams with quantum pendulum spectra: from Bessel beams to Gaussian beam-beams.

    PubMed

    Dennis, Mark R; Ring, James D

    2013-09-01

    We describe a new class of propagation-invariant light beams with Fourier transform given by an eigenfunction of the quantum mechanical pendulum. These beams, whose spectra (restricted to a circle) are doubly periodic Mathieu functions in azimuth, depend on a field strength parameter. When the parameter is zero, pendulum beams are Bessel beams, and as the parameter approaches infinity, they resemble transversely propagating one-dimensional Gaussian wave packets (Gaussian beam-beams). Pendulum beams are the eigenfunctions of an operator that interpolates between the squared angular momentum operator and the linear momentum operator. The analysis reveals connections with Mathieu beams, and insight into the paraxial approximation.

  5. Narrative text analysis of accident reports with tractors, self-propelled harvesting machinery and materials handling machinery in Austrian agriculture from 2008 to 2010 - a comparison.

    PubMed

    Mayrhofer, Hannes; Quendler, Elisabeth; Boxberger, Josef

    2014-01-01

    The aim of this study was the identification of accident scenarios and causes by analysing existing accident reports of recognized agricultural occupational accidents with tractors, self-propelled harvesting machinery and materials handling machinery from 2008 to 2010. As a result of a literature-based evaluation of past accident analyses, the narrative text analysis was chosen as an appropriate method. A narrative analysis of the text fields of accident reports that farmers used to report accidents to insurers was conducted to obtain detailed information about the scenarios and causes of accidents. This narrative analysis of reports was made the first time and yielded first insights for identifying antecedents of accidents and potential opportunities for technical based intervention. A literature and internet search was done to discuss and confirm the findings. The narrative text analysis showed that in more than one third of the accidents with tractors and materials handling machinery the vehicle rolled or tipped over. The most relevant accident scenarios with harvesting machinery were being trapped and falling down. The direct comparison of the analysed machinery categories showed that more than 10% of the accidents in each category were caused by technical faults, slippery or muddy terrain and incorrect or inappropriate operation of the vehicle. Accidents with tractors, harvesting machinery and materials handling machinery showed similarities in terms of causes, circumstances and consequences. Certain technical and communicative measures for accident prevention could be used for all three machinery categories. Nevertheless, some individual solutions for accident prevention, which suit each specific machine type, would be necessary.

  6. Development of a Short-Duration Drive Cycle to Represent Long-Term Measured Drive Cycle Data: Evaluation of Truck Efficiency Technologies in Class 8 Tractor Trailers

    SciTech Connect

    LaClair, Tim; Gao, Zhiming; Fu, Joshua; Calcagno, Jimmy; Yun, Jeongran

    2014-12-01

    Quantifying the fuel savings and emissions reductions that can be achieved from truck fuel efficiency technologies for a fleet's specific usage allows the fleet to select a combination of technologies that will yield the greatest operational efficiency and profitability. An accurate characterization of usage for the fleet is critical for such an evaluation; however, short-term measured drive cycle data do not generally reflect overall usage very effectively. This study presents a detailed analysis of vehicle usage in a commercial vehicle fleet and demonstrates the development of a short-duration synthetic drive cycle with measured drive cycle data collected over an extended period of time. The approach matched statistical measures of the vehicle speed with acceleration history and integrated measured grade data to develop a compressed drive cycle that accurately represents total usage. Drive cycle measurements obtained during a full year from six tractor trailers in normal operations in a less-than-truckload carrier were analyzed to develop a synthetic drive cycle. The vehicle mass was also estimated to account for the variation of loads that the fleet experienced. These drive cycle and mass data were analyzed with a tractive energy analysis to quantify the benefits in terms of fuel efficiency and reduced carbon dioxide emissions that can be achieved on Class 8 tractor trailers by using advanced efficiency technologies, either individually or in combination. Although differences exist between Class 8 tractor trailer fleets, this study provides valuable insight into the energy and emissions reduction potential that various technologies can bring in this important trucking application. Finally, the methodology employed for generating the synthetic drive cycle serves as a rigorous approach to develop an accurate usage characterization that can be used to effectively compress large quantities of drive cycle data.

  7. Development of a Short-Duration Drive Cycle to Represent Long-Term Measured Drive Cycle Data: Evaluation of Truck Efficiency Technologies in Class 8 Tractor Trailers

    DOE PAGES

    LaClair, Tim; Gao, Zhiming; Fu, Joshua; Calcagno, Jimmy; Yun, Jeongran

    2014-12-01

    Quantifying the fuel savings and emissions reductions that can be achieved from truck fuel efficiency technologies for a fleet's specific usage allows the fleet to select a combination of technologies that will yield the greatest operational efficiency and profitability. An accurate characterization of usage for the fleet is critical for such an evaluation; however, short-term measured drive cycle data do not generally reflect overall usage very effectively. This study presents a detailed analysis of vehicle usage in a commercial vehicle fleet and demonstrates the development of a short-duration synthetic drive cycle with measured drive cycle data collected over an extendedmore » period of time. The approach matched statistical measures of the vehicle speed with acceleration history and integrated measured grade data to develop a compressed drive cycle that accurately represents total usage. Drive cycle measurements obtained during a full year from six tractor trailers in normal operations in a less-than-truckload carrier were analyzed to develop a synthetic drive cycle. The vehicle mass was also estimated to account for the variation of loads that the fleet experienced. These drive cycle and mass data were analyzed with a tractive energy analysis to quantify the benefits in terms of fuel efficiency and reduced carbon dioxide emissions that can be achieved on Class 8 tractor trailers by using advanced efficiency technologies, either individually or in combination. Although differences exist between Class 8 tractor trailer fleets, this study provides valuable insight into the energy and emissions reduction potential that various technologies can bring in this important trucking application. Finally, the methodology employed for generating the synthetic drive cycle serves as a rigorous approach to develop an accurate usage characterization that can be used to effectively compress large quantities of drive cycle data.« less

  8. Wind-Tunnel Tests of Several Model Tractor-Propeller and Pusher-Propeller Wing Extension-Shaft Arrangements, Special Report

    NASA Technical Reports Server (NTRS)

    Harmon, Hubert N.

    1941-01-01

    Tests were made in the 20-foot propeller-research tunnel to investigate the possibility of obtaining increased net efficiencies of propeller-nacelle units by enclosing the engines in the wings and by using extension shafts. A wing of 5-foot chord was fitted with a propeller drive assembly providing for several axial locations of tractor propellers and pusher propellers. A three-blade 4-foot propeller and a three-blade 3 1/2-foot propeller of special design were tested in this wing with spinners and fairings ranging in diameter from 6 to 16 inches. A 16-inch NACA cowling was tested for comparative purposes. Two types of cuffs were also employed. It was found that the net efficiency of a conventional round-shank propeller mounted on an extension shaft in front of or behind a wing increased with an increase in the diameter of the spinner and the shaft housing within the scope of the tests. The largest spinner used had a diameter that might favorably compare with that of a radial engine cowling. The efficiencies for the pusher position appeared to be more critically affected by spinner size than those for the tractor position. The spinners with large diameters for the pusher position resulted in a higher efficiency than those for the corresponding tractor arrangements; the reverse was true for the small spinners. The use of propeller cuffs in combination with a spinner of small diameter generally resulted in net efficiencies that were comparable with those found for the large-spinner combinations.

  9. Negative optical spin torque wrench of a non-diffracting non-paraxial fractional Bessel vortex beam

    NASA Astrophysics Data System (ADS)

    Mitri, F. G.

    2016-10-01

    An absorptive Rayleigh dielectric sphere in a non-diffracting non-paraxial fractional Bessel vortex beam experiences a spin torque. The axial and transverse radiation spin torque components are evaluated in the dipole approximation using the radiative correction of the electric field. Particular emphasis is given on the polarization as well as changing the topological charge α and the half-cone angle of the beam. When α is zero, the axial spin torque component vanishes. However, when α becomes a real positive number, the vortex beam induces left-handed (negative) axial spin torque as the sphere shifts off-axially from the center of the beam. The results show that a non-diffracting non-paraxial fractional Bessel vortex beam is capable of inducing a spin reversal of an absorptive Rayleigh sphere placed arbitrarily in its path. Potential applications are yet to be explored in particle manipulation, rotation in optical tweezers, optical tractor beams, and the design of optically-engineered metamaterials to name a few areas.

  10. An Analysis of Once-per-revolution Oscillating Aerodynamic Thrust Loads on Single-Rotation Propellers on Tractor Airplanes at Zero Yaw

    NASA Technical Reports Server (NTRS)

    Rogallo, Vernon L; Yaggy, Paul F; Mccloud, John L , III

    1956-01-01

    A simplified procedure is shown for calculating the once-per-revolution oscillating aerodynamic thrust loads on propellers of tractor airplanes at zero yaw. The only flow field information required for the application of the procedure is a knowledge of the upflow angles at the horizontal center line of the propeller disk. Methods are presented whereby these angles may be computed without recourse to experimental survey of the flow field. The loads computed by the simplified procedure are compared with those computed by a more rigorous method and the procedure is applied to several airplane configurations which are believed typical of current designs. The results are generally satisfactory.

  11. Prediction of the effects of propeller operation on the static longitudinal stability of single-engine tractor monoplanes with flaps retracted

    NASA Technical Reports Server (NTRS)

    Weil, Joseph; Sleeman, William C , Jr

    1949-01-01

    The effects of propeller operation on the static longitudinal stability of single-engine tractor monoplanes are analyzed, and a simple method is presented for computing power-on pitching-moment curves for flap-retracted flight conditions. The methods evolved are based on the results of powered-model wind-tunnel investigations of 28 model configurations. Correlation curves are presented from which the effects of power on the downwash over the tail and the stabilizer effectiveness can be rapidly predicted. The procedures developed enable prediction of power-on longitudinal stability characteristics that are generally in very good agreement with experiment.

  12. Antenna Beam Coverage Concepts

    NASA Technical Reports Server (NTRS)

    Estabrook, Polly; Motamedi, Masoud

    1990-01-01

    The strawman Personal Access Satellite System (PASS) design calls for the use of a CONUS beam for transmission between the supplier and the satellite and for fixed beams for transmission between the basic personal terminal and the satellite. The satellite uses a 3 m main reflector for transmission at 20 GHz and a 2 m main reflector for reception at 30 GHz. There are several types of spot beams under consideration for the PASS system besides fixed beams. The beam pattern of a CONUS coverage switched beam is shown along with that of a scanning beam. A switched beam refers to one in which the signal from the satellite is connected alternatively to various feed horns. Scanning beams are taken to mean beams whose footprints are moved between contiguous regions in the beam's coverage area. The advantages and disadvantages of switched and/or scanning beams relative to fixed beams. The consequences of using switched/scanning in lieu of fixed beams in the PASS design and attempts are made to evaluate the listed advantages and disadvantages. Two uses of switched/scanning beams are examined. To illustrate the implications of switched beams use on PASS system design, operation at two beam scan rates is explored.

  13. Multi-Frequency Microwaves Plasma Production for Active Profile Control of Ion Beams on a Large Bore ECR Ion Source with Permanent Magnets

    SciTech Connect

    Sakamoto, Naoki; Kato, Yushi; Kiriyama, Ryutaro; Takenaka, Tomoya; Sato, Fuminobu; Iida, Toshiyuki

    2011-01-07

    A new concept on magnetic field of plasma production and confinement by using permanent magnets, i.e. cylindrically comb-shaped magnets, has been proposed to enhance efficiency of an electron cyclotron resonance (ECR) plasma for broad and dense ion beam source under the low pressure and also the low microwave power. The resonance zones corresponding to the fundamental ECR for 2.45 GHz and 11-13 GHz frequency are constructed at different positions. The profiles of the plasma parameters in the ECR ion source are different from each frequency of microwave. Large bore extractor is set at the opposite side against the microwave feeds. It is found that differences of their profiles also appear at those of ion beam profiles. We conducted to launch simultaneously multiplex frequency microwaves controlled individually, and tried to control the profiles of the plasma parameters and then those of extracted ion beam.

  14. Ultrahigh B doping ({<=}10{sup 22} cm{sup -3}) during Si(001) gas-source molecular-beam epitaxy: B incorporation, electrical activation, and hole transport

    SciTech Connect

    Glass, G.; Kim, H.; Desjardins, P.; Taylor, N.; Spila, T.; Lu, Q.; Greene, J. E.

    2000-03-15

    Si(001) layers doped with B concentrations C{sub B} between 1x10{sup 17} and 1.2x10{sup 22} cm{sup -3} (24 at %) were grown on Si(001)2x1 at temperatures T{sub s}=500-850 degree sign C by gas-source molecular-beam epitaxy from Si{sub 2}H{sub 6} and B{sub 2}H{sub 6}. C{sub B} increases linearly with the incident precursor flux ratio J{sub B{sub 2}}{sub H{sub 6}}/J{sub Si{sub 2}}{sub H{sub 6}} and B is incorporated into substitutional electrically active sites at concentrations up to C{sub B}{sup *}(T{sub s}) which, for T{sub s}=600 degree sign C, is 2.5x10{sup 20} cm{sup -3}. At higher B concentrations, C{sub B} increases faster than J{sub B{sub 2}}{sub H{sub 6}}/J{sub Si{sub 2}}{sub H{sub 6}} and there is a large and discontinuous decrease in the activated fraction of incorporated B. However, the total activated B concentration continues to increase and reaches a value of N{sub B}=1.3x10{sup 21} cm{sup -3} with C{sub B}=1.2x10{sup 22} cm{sup -3}. High-resolution x-ray diffraction (HR-XRD) and reciprocal space mapping measurements show that all films, irrespective of C{sub B} and T{sub s}, are fully strained. No B precipitates or misfit dislocations were detected by HR-XRD or transmission electron microscopy. The lattice constant in the film growth direction a{sub (perpendicular} {sub sign)} decreases linearly with increasing C{sub B} up to the limit of full electrical activation and continues to decrease, but nonlinearly, with C{sub B}>C{sub B}{sup *}. Room-temperature resistivity and conductivity mobility values are in good agreement with theoretical values for B concentrations up to C{sub B}=2.5x10{sup 20} and 2x10{sup 21} cm{sup -3}, respectively. All results can be explained on the basis of a model which accounts for strong B surface segregation to the second-layer with a saturation coverage {theta}{sub B,sat} of 0.5 ML (corresponding to C{sub B}=C{sub B}{sup *}). At higher C{sub B} (i.e., {theta}{sub B}>{theta}{sub B,sat}), B accumulates in the upper layer as

  15. Telecommunication using muon beams

    DOEpatents

    Arnold, Richard C.

    1976-01-01

    Telecommunication is effected by generating a beam of mu mesons or muons, varying a property of the beam at a modulating rate to generate a modulated beam of muons, and detecting the information in the modulated beam at a remote location.

  16. Results on intense beam focusing and neutralization from the neutralized beam experiment

    SciTech Connect

    Roy, P.K.; Yu, S.S.; Eylon, S.; Henestroza, E.; Anders, A.; Bieniosek, F.M.; Greenway, W.G.; Logan, B.G.; Waldron, W.L.; Vanecek, D.L.; Welch, D.R.; Rose, D.V.; Davidson, R.C.; Efthimion, P.C.; Gilson, E.P.; Sefkow, A.B.; Sharp, W.M.

    2003-10-31

    We have demonstrated experimental techniques to provide active neutralization for space-charge dominated beams as well as to prevent uncontrolled ion beam neutralization by stray electrons. Neutralization is provided by a localized plasma injected from a cathode arc source. Unwanted secondary electrons produced at the wall by halo particle impact are suppressed using a radial mesh liner that is positively biased inside a beam drift tube. We present measurements of current transmission, beam spot size as a function of axial position, beam energy and plasma source conditions. Detailed comparisons with theory are also presented.

  17. Parabolic scaling beams.

    PubMed

    Gao, Nan; Xie, Changqing

    2014-06-15

    We generalize the concept of diffraction free beams to parabolic scaling beams (PSBs), whose normalized intensity scales parabolically during propagation. These beams are nondiffracting in the circular parabolic coordinate systems, and all the diffraction free beams of Durnin's type have counterparts as PSBs. Parabolic scaling Bessel beams with Gaussian apodization are investigated in detail, their nonparaxial extrapolations are derived, and experimental results agree well with theoretical predictions.

  18. Automated beam builder

    NASA Technical Reports Server (NTRS)

    Muench, W. K.

    1980-01-01

    Requirements for the space fabrication of large space structures are considered with emphasis on the design, development, manufacture, and testing of a machine which automatically produces a basic building block aluminum beam. Particular problems discussed include those associated with beam cap forming; brace storage, dispensing, and transporting; beam component fastening; and beam cut-off. Various critical process tests conducted to develop technology for a machine to produce composite beams are also discussed.

  19. SUMMARY OF BEAM BEAM OBSERVATIONS DURING STORES IN RHIC.

    SciTech Connect

    FISCHER,W.

    2003-05-19

    During stores, the beam-beam interaction has a significant impact on the beam and luminosity lifetimes in RHIC. This was observed in heavy ion, and even more pronounced in proton collisions. Observations include measurements of beam-beam induced tune shifts, lifetime and emittance growth measurements with and without beam-beam interaction, and background rates as a function of tunes. In addition, RHIC is currently the only hadron collider in which strong-strong beam-beam effects can be seen. Coherent beam-beam modes were observed, and suppressed by tune changes. In this article we summarize the most important beam-beam observations made during stores so far.

  20. A Summary of the Experimental Results for a Generic Tractor-Trailer in the Ames Research Center 7- by 10-Foot and 12-Foot Wind Tunnels

    NASA Technical Reports Server (NTRS)

    Storms, Bruce L.; Satran, Dale R.; Heineck, James T.; Walker, Stephen M.

    2006-01-01

    Experimental measurements of a generic tractor-trailer were obtained in two wind tunnels at Ames Research Center. After a preliminary study at atmospheric conditions in the 7- by 10-Foot Wind Tunnel, additional testing was conducted at Reynolds numbers corresponding to full-scale highway speeds in the 12-Foot Pressure Wind Tunnel. To facilitate computational modeling, the 1:8-scale geometry, designated the Generic Conventional Model, included a simplified underbody and omitted many small-scale details. The measurements included overall and component forces and moments, static and dynamic surface pressures, and three-component particle image velocimetry. This summary report highlights the effects of numerous drag reduction concepts and provides details of the model installation in both wind tunnels. To provide a basis for comparison, the wind-averaged drag coefficient was tabulated for all configurations tested. Relative to the baseline configuration representative of a modern class-8 tractor-trailer, the most effective concepts were the trailer base flaps and trailer belly box providing a drag-coefficient reduction of 0.0855 and 0.0494, respectively. Trailer side skirts were less effective yielding a drag reduction of 0.0260. The database of this experimental effort is publicly available for further analysis.

  1. Tevatron beam-beam compensation project progress

    SciTech Connect

    Shiltsev, V.; Zhang, X.L.; Kuznetsov, G.; Pfeffer, H.; Saewert, G.; Zimmermann, F.; Tiunov, M.; Bishofberger, K.; Bogdanov, I.; Kashtanov, E.; Kozub, S.; Sytnik, V.; Tkachenko, L.; /Serpukhov, IHEP

    2005-05-01

    In this paper, we report the progress of the Tevatron Beam-Beam Compensation (BBC) project [1]. Electron beam induced proton and antiproton tuneshifts have been reported in [2], suppression of an antiproton emittance growth has been observed, too [1]. Currently, the first electron lens (TEL1) is in operational use as the Tevatron DC beam cleaner. We have made a lot of the upgrades to improve its stability [3]. The 2nd Tevatron electron lens (TEL2) is under the final phase of development and preparation for installation in the Tevatron.

  2. Electron beam diagnostic for profiling high power beams

    DOEpatents

    Elmer, John W.; Palmer, Todd A.; Teruya, Alan T.

    2008-03-25

    A system for characterizing high power electron beams at power levels of 10 kW and above is described. This system is comprised of a slit disk assembly having a multitude of radial slits, a conducting disk with the same number of radial slits located below the slit disk assembly, a Faraday cup assembly located below the conducting disk, and a start-stop target located proximate the slit disk assembly. In order to keep the system from over-heating during use, a heat sink is placed in close proximity to the components discussed above, and an active cooling system, using water, for example, can be integrated into the heat sink. During use, the high power beam is initially directed onto a start-stop target and after reaching its full power is translated around the slit disk assembly, wherein the beam enters the radial slits and the conducting disk radial slits and is detected at the Faraday cup assembly. A trigger probe assembly can also be integrated into the system in order to aid in the determination of the proper orientation of the beam during reconstruction. After passing over each of the slits, the beam is then rapidly translated back to the start-stop target to minimize the amount of time that the high power beam comes in contact with the slit disk assembly. The data obtained by the system is then transferred into a computer system, where a computer tomography algorithm is used to reconstruct the power density distribution of the beam.

  3. ION BEAM COLLIMATOR

    DOEpatents

    Langsdorf, A.S. Jr.

    1957-11-26

    A device is described for defining a beam of high energy particles wherein the means for defining the beam in the horizontal and vertical dimension are separately adjustable and the defining members are internally cooled. In general, the device comprises a mounting block having a central opening through which the beam is projected, means for rotatably supporting two pairs of beam- forming members, passages in each member for the flow of coolant; the beam- forming members being insulated from each other and the block, and each having an end projecting into the opening. The beam-forming members are adjustable and may be cooperatively positioned to define the beam passing between the end of the members. To assist in projecting and defining the beam, the member ends have individual means connected thereto for indicating the amount of charge collected thereon due to beam interception.

  4. An MCNPX accelerator beam source

    SciTech Connect

    Durkee, Joe W.; Elson, Jay S.; Jason, Andrew; Johns, Russell C.; Waters, Laurie S.

    2009-06-04

    MCNPX is a powerful Monte Carlo code that can be used to conduct sophisticated radiation-transport simulations involving complex physics and geometry. Although MCNPX possesses a wide assortment of standardized modeling tools, there are instances in which a user's needs can eclipse existing code capabilities. Fortunately, although it may not be widely known, MCNPX can accommodate many customization needs. In this article, we demonstrate source-customization capability for a new SOURCE subroutine as part of our development to enable simulations involving accelerator beams for active-interrogation studies. Simulation results for a muon beam are presented to illustrate the new accelerator-source capability.

  5. Beam position monitor

    DOEpatents

    Alkire, Randy W.; Rosenbaum, Gerold; Evans, Gwyndaf

    2003-07-22

    An apparatus for determining the position of an x-ray beam relative to a desired beam axis. Where the apparatus is positioned along the beam path so that a thin metal foil target intersects the x-ray beam generating fluorescent radiation. A PIN diode array is positioned so that a portion of the fluorescent radiation is intercepted by the array resulting in an a series of electrical signals from the PIN diodes making up the array. The signals are then analyzed and the position of the x-ray beam is determined relative to the desired beam path.

  6. Pyramid beam splitter

    DOEpatents

    McKeown, Mark H.; Beason, Steven C.; Fairer, George

    1992-01-01

    The apparatus of the present invention provides means for obtaining accurate, dependable, measurement of bearings and directions for geologic mapping in subterranean shafts, such as, for example, nuclear waste storage investigations. In operation, a laser beam is projected along a reference bearing. A pyramid is mounted such that the laser beam is parallel to the pyramid axis and can impinge on the apex of the pyramid thus splitting the beam several ways into several beams at right angles to each other and at right angles to the reference beam. The pyramid is also translatable and rotatable in a plane perpendicular to the reference beam.

  7. A study of the structural activation caused by proton beam loss in the {open_quotes}accelerator production of tritium{close_quotes} LINAC

    SciTech Connect

    Daemen, L.L.; Beard, C.A.; Eaton, S.L.; Waters, L.S.; Wilson, W.B.

    1997-01-01

    The Accelerator Production of Tritium (APT) project at Los Alamos National Laboratory makes use of a high power linear proton accelerator to produce neutrons via spallation reactions m a heavy metal target. The fast spallation neutrons are moderated by a heavy water blanket, and used to produce tritium by means of the reaction: {sup 3}He(n,p)T, APT 1993. Various accelerator designs are currently under consideration. At the time when this study was performed, the project called for a 1 GeV proton linear accelerator with a beam current of 200 mA, i.e., a proton beam power of 200 MW. Given the high power at which the APT accelerator is expected to operate, as well as the heavy maintenance that is likely to be required to keep it operating, it is essential to consider health physics issues at an early stage of the design.

  8. Tumortherapy with ion beams

    NASA Astrophysics Data System (ADS)

    Kraft, G.; Heary Ion Therapy Collaboration

    2000-11-01

    Beams of heavy-charged particles like protons or carbon ions represent the optimum tool for the treatment of deep-seated inoperable tumors: in contrast to the conventionally used photons the dose increases along with the penetration depth through the body, culminating in a sharp maximum at the end of the particle range. In order to achieve a precisely conform irradiation of the selected target volume, this maximum can be shifted in depth by energy variation and distributed laterally through magnetic deflection of the particle beam. Because carbon ions have a lateral scattering of only about 1 mm at 10 cm depth they offer the most conform irradiation. In addition to this excellent physical selectivity the biological efficiency concerning cell killing increases towards the end of the carbon ions' range. Therefore, the increase in dose is potentiated by an increase in biological efficiency. Finally, the stopping of the carbon ions can be monitored by tracing a small amount of β + active 10C and 11C ions which are produced in nuclear reactions with atoms of the penetrated tissue. This β + distribution can be visualized by applying PET-techniques, thus allowing a good control of the beam distribution. At GSI Darmstadt a heavy-ion therapy unit has been designed and constructed in collaboration with the Radiological Clinic and the DKFZ Heidelberg and the FZR Dresden. The layout of this facility as well as the treatment of now more than 30 patients will be reported on. The proposal for the layout of a dedicated medical facility at Heidelberg will be presented

  9. Test of electron beam technology on Savannah River Laboratory low-activity aqueous waste for destruction of benzene, benzene derivatives, and bacteria

    SciTech Connect

    Dougal, R.A.

    1993-08-01

    High energy radiation was studied as a means for destroying hazardous organic chemical wastes. Tests were conducted at bench scale with a {sup 60}Co source, and at full scale (387 l/min) with a 1.5 MV electron beam source. Bench scale tests for both benzene and phenol included 32 permutations of water quality factors. For some water qualities, as much as 99.99% of benzene or 90% of phenol were removed by 775 krads of {sup 60}Co irradiation. Full scale testing for destruction of benzene in a simulated waste-water mix showed loss of 97% of benzene following an 800 krad dose and 88% following a 500 krad dose. At these loss rates, approximately 5 Mrad of electron beam irradiation is required to reduce concentrations from 100 g/l to drinking water quality (5 {mu}g/l). Since many waste streams are also inhabited by bacterial populations which may affect filtering operations, the effect of irradiation on those populations was also studied. {sup 60}Co and electron beam irradiation were both lethal to the bacteria studied at irradiation levels far lower than were necessary to remove organic contaminants.

  10. Design of a new sensor for determination of the effects of tractor field usage in southern Spain: soil sinkage and alterations in the cone index and dry bulk density.

    PubMed

    Valera, Diego L; Gil, Jesús; Agüera, Juan

    2012-01-01

    Variations in sinkage and cone index are of crucial importance when planning fieldwork, and for determining the trafficability of farm machinery. Many studies have highlighted the link between higher values of these parameters and dramatic decreases in crop yield. Variations in the dry bulk density and cone index of clayey soil in Southern Spain were measured following each of five successive passes over the same land with the three types of tractor most widely used in the area (tracked, two-wheel drive and four-wheel drive). In addition, sinkage (rut depth) of the running gear was measured using a laser microrelief profile meter. This device, which integrates three sensors, was specifically designed for these experiments, as was an electrical penetrometer to determine the cone index, and both instruments proved reliable and accurate in the field. The main goal of this study was to design, manufacture and test these new devices. The first pass caused most soil alteration when compared to successive passes for all types of tractor tested and soil conditions prevailing during the tests. (Heavier) four-wheel drive tractors were found to cause greater soil damage (sinkage, cone index and dry bulk density) than two-wheel drive and track tractors. There was no statistically significant difference between the two latter types. The greatest alterations were recorded in the top 10 cm of the soil. The results show that soil compaction should be avoided as much as possible. This can be achieved by ensuring that tractors always travel along the same tracks, especially in the wet season. At present these aspects are not considered by farmers in this area. PMID:23202006

  11. Design of a New Sensor for Determination of the Effects of Tractor Field Usage in Southern Spain: Soil Sinkage and Alterations in the Cone Index and Dry Bulk Density

    PubMed Central

    Valera, Diego L.; Gil, Jesús; Agüera, Juan

    2012-01-01

    Variations in sinkage and cone index are of crucial importance when planning fieldwork, and for determining the trafficability of farm machinery. Many studies have highlighted the link between higher values of these parameters and dramatic decreases in crop yield. Variations in the dry bulk density and cone index of clayey soil in Southern Spain were measured following each of five successive passes over the same land with the three types of tractor most widely used in the area (tracked, two-wheel drive and four-wheel drive). In addition, sinkage (rut depth) of the running gear was measured using a laser microrelief profile meter. This device, which integrates three sensors, was specifically designed for these experiments, as was an electrical penetrometer to determine the cone index, and both instruments proved reliable and accurate in the field. The main goal of this study was to design, manufacture and test these new devices. The first pass caused most soil alteration when compared to successive passes for all types of tractor tested and soil conditions prevailing during the tests. (Heavier) four-wheel drive tractors were found to cause greater soil damage (sinkage, cone index and dry bulk density) than two-wheel drive and track tractors. There was no statistically significant difference between the two latter types. The greatest alterations were recorded in the top 10 cm of the soil. The results show that soil compaction should be avoided as much as possible. This can be achieved by ensuring that tractors always travel along the same tracks, especially in the wet season. At present these aspects are not considered by farmers in this area. PMID:23202006

  12. Successful Beam-Beam Tuneshift Compensation

    SciTech Connect

    Bishofberger, Kip Aaron

    2005-01-01

    The performance of synchrotron colliders has been limited by the beam-beam limit, a maximum tuneshift that colliding bunches could sustain. Due to bunch-to-bunch tune variation and intra-bunch tune spread, larger tuneshifts produce severe emittance growth. Breaking through this constraint has been viewed as impossible for several decades. This dissertation introduces the physics of ultra-relativistic synchrotrons and low-energy electron beams, with emphasis placed on the limits of the Tevatron and the needs of a tuneshift-compensation device. A detailed analysis of the Tevatron Electron Lens (TEL) is given, comparing theoretical models to experimental data whenever possible. Finally, results of Tevatron operations with inclusion of the TEL are presented and analyzed. It is shown that the TEL provides a way to shatter the previously inescapable beam-beam limit.

  13. BEAMS3D Neutral Beam Injection Model

    SciTech Connect

    Lazerson, Samuel

    2014-04-14

    With the advent of applied 3D fi elds in Tokamaks and modern high performance stellarators, a need has arisen to address non-axisymmetric effects on neutral beam heating and fueling. We report on the development of a fully 3D neutral beam injection (NBI) model, BEAMS3D, which addresses this need by coupling 3D equilibria to a guiding center code capable of modeling neutral and charged particle trajectories across the separatrix and into the plasma core. Ionization, neutralization, charge-exchange, viscous velocity reduction, and pitch angle scattering are modeled with the ADAS atomic physics database [1]. Benchmark calculations are presented to validate the collisionless particle orbits, neutral beam injection model, frictional drag, and pitch angle scattering effects. A calculation of neutral beam heating in the NCSX device is performed, highlighting the capability of the code to handle 3D magnetic fields.

  14. Anomalous beam diffusion near beam-beam synchrobetatron resonances

    NASA Astrophysics Data System (ADS)

    Sen, Tanaji

    2012-10-01

    The diffusion process near low order synchrobetatron resonances driven by beam-beam interactions at a crossing angle is investigated. Macroscopic observables such as beam emittance, lifetime, and beam profiles are calculated. These are followed with detailed studies of microscopic quantities such as the evolution of the variance at several transverse amplitudes and single particle probability distribution functions. We present evidence to show that the observed diffusion is anomalous and the dynamics follows a non-Markovian continuous time random walk process. We derive a modified master equation to replace the Chapman-Kolmogorov equation in action-angle space and a fractional diffusion equation to describe the density evolution for this class of processes.

  15. The 50 MeV Beam Test Facility at LBL

    SciTech Connect

    Leemans, W.; Behrsing, G.; Kim, K.J.; Krupnick, J.; Matuk, C.; Selph, F.; Chattopadhyay, S.

    1993-05-01

    A new beam line, expected to be built by September 1993, will transport the 50 MeV electron beam from the ALS LINAC into an experimental area to support various R&D activities in the Center for Beam Physics at LBL. A variety of experiments are planned involving the interaction of such a relativistic electron beam with plasmas (plasma focusing), laser beams (generation of femtosecond X-ray pulses) and electromagnetic cavities (Crab cavities etc....). The beam line is designed using the measured emittance and Twiss parameters of the ALS linac. It accommodates the different requirements of the various experiments on the electron beam properties (charge, energy, pulse length) and on the handling of the beam before and after the interaction point. Special attention has also been given to incorporate diagnostics for measuring the beam properties (such as the electron energy, bunch length and charge) needed in the interpretation of the experiments.

  16. High energy beam lines

    NASA Astrophysics Data System (ADS)

    Marchetto, M.; Laxdal, R. E.

    2014-01-01

    The ISAC post accelerator comprises an RFQ, DTL and SC-linac. The high energy beam lines connect the linear accelerators as well as deliver the accelerated beams to two different experimental areas. The medium energy beam transport (MEBT) line connects the RFQ to the DTL. The high energy beam transport (HEBT) line connects the DTL to the ISAC-I experimental stations (DRAGON, TUDA-I, GPS). The DTL to superconducting beam (DSB) transport line connects the ISAC-I and ISAC-II linacs. The superconducting energy beam transport (SEBT) line connects the SC linac to the ISAC-II experimental station (TUDA-II, HERACLES, TIGRESS, EMMA and GPS). All these lines have the function of transporting and matching the beams to the downstream sections by manipulating the transverse and longitudinal phase space. They also contain diagnostic devices to measure the beam properties.

  17. Electron Beam Freeform Fabrication

    NASA Video Gallery

    Electron Beam Freeform Fabrication (EBF3) is a process by which NASA hopes to build metal parts in zero gravity environments. It's a layer-additive process that uses an electron beam and a solid wi...

  18. Intra-beam scattering

    NASA Astrophysics Data System (ADS)

    Piwinski, A.

    Intra-beam scattering is analysed and the rise times or damping times of the beam dimensions are derived. The theoretical results are compared with experimental values obtained on the CERN AA and SPS machines.

  19. Laser-Beam Separator

    NASA Technical Reports Server (NTRS)

    Mcdermid, I. S.

    1984-01-01

    Train of prisms and optical stop separate fundamental beam of laser from second and higher order harmonics of beam produced in certain crystals and by stimulated Raman scattering in gases and liquids.

  20. Electron beam focusing system

    SciTech Connect

    Dikansky, N.; Nagaitsev, S.; Parkhomchuk, V.

    1997-09-01

    The high energy electron cooling requires a very cold electron beam. Thus, the electron beam focusing system is very important for the performance of electron cooling. A system with and without longitudinal magnetic field is presented for discussion. Interaction of electron beam with the vacuum chamber as well as with the background ions and stored antiprotons can cause the coherent electron beam instabilities. Focusing system requirements needed to suppress these instabilities are presented.

  1. Beam Dynamics for ARIA

    SciTech Connect

    Ekdahl, Carl August Jr.

    2014-10-14

    Beam dynamics issues are assessed for a new linear induction electron accelerator being designed for flash radiography of large explosively driven hydrodynamic experiments. Special attention is paid to equilibrium beam transport, possible emittance growth, and beam stability. It is concluded that a radiographic quality beam will be produced possible if engineering standards and construction details are equivalent to those on the present radiography accelerators at Los Alamos.

  2. PARTICLE BEAM TRACKING CIRCUIT

    DOEpatents

    Anderson, O.A.

    1959-05-01

    >A particle-beam tracking and correcting circuit is described. Beam induction electrodes are placed on either side of the beam, and potentials induced by the beam are compared in a voltage comparator or discriminator. This comparison produces an error signal which modifies the fm curve at the voltage applied to the drift tube, thereby returning the orbit to the preferred position. The arrangement serves also to synchronize accelerating frequency and magnetic field growth. (T.R.H.)

  3. Confinement of bunched beams

    NASA Astrophysics Data System (ADS)

    Hess, Mark; Chen, Chiping

    2001-05-01

    The non-relativistic motion is analyzed for a highly bunched beam propagating through a perfectly conducting cylindrical pipe confined radially by a constant magnetic field parallel to the conductor axis, using a Green's function technique and Hamiltonian dynamics analysis. It is shown that for the confinement of beams with the same charge per unit length, the maximum value of the effective self-field parameter for a highly bunched beam is significantly lower than the Brillouin density limit for an unbunched beam.

  4. Relativistic-beam Pickup Test Facility

    SciTech Connect

    Kramer, S.L.; Simpson, J.; Konecny, R.; Suddeth, D.

    1983-01-01

    The electrical response of pickups and cavities to charged particle beams has been an area of considerable activity and concern for accelerator systems. With the advent of stochastic beam cooling, the position and frequency response of beam pickups has become a crucial parameter in determining the performance of these systems. The most frequently used method for measuring and calibrating beam pickups has been the use of current carrying wires to simulate relativistic beams. This method has sometimes led to incorrect predictions of the pickup response to particle beams. The reasons for the differences are not always obvious but could arise from: (1) wires are incapable of exciting or permitting many of the modes that beams excite or (2) the interaction of the wire with large arrays of pickups produce results which are not easily predicted. At Argonne these deficiencies are resolved by calibrating pickups with a relativistic electron beam. This facility is being used extensively by several groups to measure beam pickup devices and is the primary calibration facility for pickups to be used in the FNAL TEV-I Antiproton Source.

  5. Study of beam-beam effects in eRHIC

    SciTech Connect

    Hao, Y.; Litvinenko, V.; Ptitsyn, V.

    2010-05-23

    Beam-beam effects in eRHIC have a number of unique features, which distinguish them from both hadron and lepton colliders. Due to beam-beam interaction, both electron and hadron beams would suffer quality degradation or beam loss from without proper treatments. Those features need novel study and dedicate countermeasures. We study the beam dynamics and resulting luminosity of the characteristics, including mismatch, disruption and pinch effects on electron beam, in additional to their consequences on the opposing beam as a wake field and other incoherent effects of hadron beam. We also carry out countermeasures to prevent beam quality degrade and coherent instability.

  6. Dual beam optical interferometer

    NASA Technical Reports Server (NTRS)

    Gutierrez, Roman C. (Inventor)

    2003-01-01

    A dual beam interferometer device is disclosed that enables moving an optics module in a direction, which changes the path lengths of two beams of light. The two beams reflect off a surface of an object and generate different speckle patterns detected by an element, such as a camera. The camera detects a characteristic of the surface.

  7. ATA beam director experiment

    SciTech Connect

    Lee, E.P.; Younger, F.C.; Cruz, G.E.; Nolting, E.

    1986-06-23

    This report describes beam director elements for an experiment at the Advanced Test Accelerator. The elements described include a vernier magnet for beam aiming, an achromat magnet, and an isolation system for the beam interface. These components are built at small scale for concept testing. (JDH)

  8. Cooling of stored beams

    SciTech Connect

    Mills, F.E.

    1986-10-15

    Beam cooling methods developed for the accumulation of antiprotons are being employed to assist in the performance of experiments in Nuclear and Particle Physics with ion beams stored in storage rings. The physics of beam cooling, and the ranges of utility of stochastic and electron cooling are discussed in this paper.

  9. Beam injection into RHIC

    SciTech Connect

    Fischer, W.; Hahn, H.; MacKay, W.W.; Satogata, T.; Tsoupas, N.; Zhang, W.

    1997-07-01

    During the RHIC sextant test in January 1997 beam was injected into a sixth of one of the rings for the first time. The authors describe the injection zone and its bottlenecks. They report on the commissioning of the injection system, on beam based measurements of the kickers and the application program to steer the beam.

  10. Electron beam device

    DOEpatents

    Beckner, E.H.; Clauser, M.J.

    1975-08-12

    This patent pertains to an electron beam device in which a hollow target is symmetrically irradiated by a high energy, pulsed electron beam about its periphery and wherein the outer portion of the target has a thickness slightly greater than required to absorb the electron beam pulse energy. (auth)

  11. Ionized cluster beam deposition

    NASA Astrophysics Data System (ADS)

    Kirkpatrick, A. R.

    1983-11-01

    Ionized Cluster Beam (ICB) deposition, a new technique originated by Takagi of Kyoto University in Japan, offers a number of unique capabilities for thin film metallization as well as for deposition of active semiconductor materials. ICB allows average energy per deposited atom to be controlled and involves impact kinetics which result in high diffusion energies of atoms on the growth surface. To a greater degree than in other techniques, ICB involves quantitative process parameters which can be utilized to strongly control the characteristics of films being deposited. In the ICB deposition process, material to be deposited is vaporized into a vacuum chamber from a confinement crucible at high temperature. Crucible nozzle configuration and operating temperature are such that emerging vapor undergoes supercondensation following adiabatic expansion through the nozzle.

  12. Ionized cluster beam deposition

    NASA Technical Reports Server (NTRS)

    Kirkpatrick, A. R.

    1983-01-01

    Ionized Cluster Beam (ICB) deposition, a new technique originated by Takagi of Kyoto University in Japan, offers a number of unique capabilities for thin film metallization as well as for deposition of active semiconductor materials. ICB allows average energy per deposited atom to be controlled and involves impact kinetics which result in high diffusion energies of atoms on the growth surface. To a greater degree than in other techniques, ICB involves quantitative process parameters which can be utilized to strongly control the characteristics of films being deposited. In the ICB deposition process, material to be deposited is vaporized into a vacuum chamber from a confinement crucible at high temperature. Crucible nozzle configuration and operating temperature are such that emerging vapor undergoes supercondensation following adiabatic expansion through the nozzle.

  13. BEAM CONTROL PROBE

    DOEpatents

    Chesterman, A.W.

    1959-03-17

    A probe is described for intercepting a desired portion of a beam of charged particles and for indicating the spatial disposition of the beam. The disclosed probe assembly includes a pair of pivotally mounted vanes moveable into a single plane with adjacent edges joining and a calibrated mechanical arrangement for pivoting the vancs apart. When the probe is disposed in the path of a charged particle beam, the vanes may be adjusted according to the beam current received in each vane to ascertain the dimension of the beam.

  14. Beams for kaon research

    SciTech Connect

    Pile, P.H.

    1985-01-01

    A proposed 1-2 GeV/c kaon beam line for BNL, designed to deliver momentum analyzed negative kaon beams with intensities above 10/sup 6/ per spill, is discussed. The beam intensity is expected to be about an order of magnitude greater than presently available and it is expected to be a clean beam with no more than 1:1 (..pi../sup -/,..mu../sup -/,e/sup -/)/K/sup -/. The beam line will allow a detailed investigation of strangeness -2 systems as well as continued investigations of strangeness -1 systems.

  15. Neutral beam monitoring

    DOEpatents

    Fink, Joel H.

    1981-08-18

    Method and apparatus for monitoring characteristics of a high energy neutral beam. A neutral beam is generated by passing accelerated ions through a walled cell containing a low energy neutral gas, such that charge exchange neutralizes the high energy ion beam. The neutral beam is monitored by detecting the current flowing through the cell wall produced by low energy ions which drift to the wall after the charge exchange. By segmenting the wall into radial and longitudinal segments various beam conditions are further identified.

  16. Isotope separation using tuned laser and electron beam

    NASA Technical Reports Server (NTRS)

    Trajmar, Sandor (Inventor)

    1987-01-01

    The apparatus comprises means for producing an atomic beam containing the isotope of interest and other isotopes. Means are provided for producing a magnetic field traversing the path of the atomic beam of an intensity sufficient to broaden the energy domain of the various individual magnetic sublevels of the isotope of interest and having the atomic beam passing therethrough. A laser beam is produced of a frequency and polarization selected to maximize the activation of only individual magnetic sublevels of the isotope of interest with the portion of its broadened energy domain most removed from other isotopes with the stream. The laser beam is directed so as to strike the atomic beam within the magnetic field and traverse the path of the atomic beam whereby only the isotope of interest is activated by the laser beam. The apparatus further includes means for producing a collimated and high intensity beam of electrons of narrow energy distribution within the magnetic field which is aimed so as to strike the atomic beam while the atomic beam is simultaneously struck by the laser beam and at an energy level selected to ionize the activated isotope of interest but not ground state species included therewith. Deflection means are disposed in the usual manner to collect the ions.

  17. Dosimetric accuracy of a treatment planning system for actively scanned proton beams and small target volumes: Monte Carlo and experimental validation

    NASA Astrophysics Data System (ADS)

    Magro, G.; Molinelli, S.; Mairani, A.; Mirandola, A.; Panizza, D.; Russo, S.; Ferrari, A.; Valvo, F.; Fossati, P.; Ciocca, M.

    2015-09-01

    This study was performed to evaluate the accuracy of a commercial treatment planning system (TPS), in optimising proton pencil beam dose distributions for small targets of different sizes (5-30 mm side) located at increasing depths in water. The TPS analytical algorithm was benchmarked against experimental data and the FLUKA Monte Carlo (MC) code, previously validated for the selected beam-line. We tested the Siemens syngo® TPS plan optimisation module for water cubes fixing the configurable parameters at clinical standards, with homogeneous target coverage to a 2 Gy (RBE) dose prescription as unique goal. Plans were delivered and the dose at each volume centre was measured in water with a calibrated PTW Advanced Markus® chamber. An EBT3® film was also positioned at the phantom entrance window for the acquisition of 2D dose maps. Discrepancies between TPS calculated and MC simulated values were mainly due to the different lateral spread modeling and resulted in being related to the field-to-spot size ratio. The accuracy of the TPS was proved to be clinically acceptable in all cases but very small and shallow volumes. In this contest, the use of MC to validate TPS results proved to be a reliable procedure for pre-treatment plan verification.

  18. Dosimetric accuracy of a treatment planning system for actively scanned proton beams and small target volumes: Monte Carlo and experimental validation.

    PubMed

    Magro, G; Molinelli, S; Mairani, A; Mirandola, A; Panizza, D; Russo, S; Ferrari, A; Valvo, F; Fossati, P; Ciocca, M

    2015-09-01

    This study was performed to evaluate the accuracy of a commercial treatment planning system (TPS), in optimising proton pencil beam dose distributions for small targets of different sizes (5-30 mm side) located at increasing depths in water. The TPS analytical algorithm was benchmarked against experimental data and the FLUKA Monte Carlo (MC) code, previously validated for the selected beam-line. We tested the Siemens syngo(®) TPS plan optimisation module for water cubes fixing the configurable parameters at clinical standards, with homogeneous target coverage to a 2 Gy (RBE) dose prescription as unique goal. Plans were delivered and the dose at each volume centre was measured in water with a calibrated PTW Advanced Markus(®) chamber. An EBT3(®) film was also positioned at the phantom entrance window for the acquisition of 2D dose maps. Discrepancies between TPS calculated and MC simulated values were mainly due to the different lateral spread modeling and resulted in being related to the field-to-spot size ratio. The accuracy of the TPS was proved to be clinically acceptable in all cases but very small and shallow volumes. In this contest, the use of MC to validate TPS results proved to be a reliable procedure for pre-treatment plan verification.

  19. Power beaming: Mission enabling for lunar exploration

    SciTech Connect

    Bamberger, J.A.

    1992-01-01

    This paper explores several beam power concepts proposed for powering either lunar base or rover vehicles. At present, power requirements to support lunar exploration activity are met by integral self-contained power system designs. To provide requisite energy flexibility for human expansion into space, an innovative approach to replace on-board self-contained power systems is needed. Power beaming provides an alternative approach to supplying power that would ensure increased mission flexibility while reducing total mass launched into space. Providing power to the moon presents significant design challenges because of the duration of the lunar night. Power beaming provides an alternative to solar photovoltaic systems coupled with battery storage, radioisotope thermoelectric generation, and surface nuclear power. The Synthesis Group describes power beaming as a technology supporting lunar exploration. In this analysis beam power designs are compared to conventional power generation methods.

  20. Tunable beam steering enabled by graphene metamaterials.

    PubMed

    Orazbayev, B; Beruete, M; Khromova, I

    2016-04-18

    We demonstrate tunable mid-infrared (MIR) beam steering devices based on multilayer graphene-dielectric metamaterials. The effective refractive index of such metamaterials can be manipulated by changing the chemical potential of each graphene layer. This can arbitrarily tailor the spatial distribution of the phase of the transmitted beam, providing mechanisms for active beam steering. Three different beam steerer (BS) designs are discussed: a graded-index (GRIN) graphene-based metamaterial block, an array of metallic waveguides filled with graphene-dielectric metamaterial and an array of planar waveguides created in a graphene-dielectric metamaterial block with a specific spatial profile of graphene sheets doping. The performances of the BSs are numerically analyzed, showing the tunability of the proposed designs for a wide range of output angles (up to approximately 70°). The proposed graphene-based tunable beam steering can be used in tunable transmitter/receiver modules for infrared imaging and sensing.

  1. New applications of ORNL neutral beam injectors

    SciTech Connect

    Tsai, C. C.; Peng, Yueng Kay Martin

    1998-01-01

    The injection of energetic hydrogen and deuterium atoms has been used to heat plasmas in various fusion experimental devices including tokamaks, mirrors, and stellarators. The neutral beam injection is a proven plasma heating technique for increasing plasma densities, temperatures, and pressures. For this fusion endeavor, scientists at Oak Ridge National Laboratory (ORNL) have developed multimegawatt neutral beam injectors. Various ORNL injectors have been used for studying properties of beam-heated plasmas in Oak Ridge Tokamak (ORMAK), Impurity Study Experiment-B (ISX-B), Advanced Toroidal Facility (ATF), Princeton Large Torus (PLT), and Princeton Divertor Experiment (PDX) in the United States and in Small Tight Aspect Ratio Tokamak (START) in the United Kingdom. By using a 30-cm and 100-A ion source, each ORNL neutral beam injector is capable of injecting >1.5 MW of hydrogen atoms at 50-keV for a pulse length up to 0.5 s. For increasing plasma densities and raising plasma temperatures in START, one such injector was installed and commissioned during 1995. The initial goal was to provide an injected neutral beam power of more than 0.5 MW at a beam energy of 40 keV for 20 ms. Addition of a getter pump has allowed the beam power to be raised to 1 MW at 33 keV. Recent experiments have demonstrated that neutral beam heating can play a big role in raising plasma pressures to a record volume-average beta value over 30%. ORNL neutral beam injectors have been approved for plasma heating experiments on both the TJ-II stellarator at CIEMAT, Spain, and the Mega-Amp Spherical Tokamak (MAST) at Culham Science Centre (Culham). Two proven ORNL NE injectors are being installed at the TJ-II facility. Additional ORNL beam equipment is being used to implement two 5-s NE injectors at the MAST facility. In this paper, we report and discuss the progress and plans for these neutral beam activities.

  2. Initial alignment method for free space optics laser beam

    NASA Astrophysics Data System (ADS)

    Shimada, Yuta; Tashiro, Yuki; Izumi, Kiyotaka; Yoshida, Koichi; Tsujimura, Takeshi

    2016-08-01

    The authors have newly proposed and constructed an active free space optics transmission system. It is equipped with a motor driven laser emitting mechanism and positioning photodiodes, and it transmits a collimated thin laser beam and accurately steers the laser beam direction. It is necessary to introduce the laser beam within sensible range of the receiver in advance of laser beam tracking control. This paper studies an estimation method of laser reaching point for initial laser beam alignment. Distributed photodiodes detect laser luminescence at respective position, and the optical axis of laser beam is analytically presumed based on the Gaussian beam optics. Computer simulation evaluates the accuracy of the proposed estimation methods, and results disclose that the methods help us to guide the laser beam to a distant receiver.

  3. AGS slow extracted beam improvement

    SciTech Connect

    Marneris, I.; Danowski, G.; Sandberg, J.; Soukas, A.

    1997-07-01

    The Brookhaven AGS is a strong focusing accelerator which is used to accelerate protons and various heavy ion species to an equivalent proton energy of 29 GeV. Since the late 1960`s it has been serving high energy physics (HEP - proton beam) users of both slow and fast extracted beams. The AGS fixed target program presently uses primary proton and heavy ion beams (HIP) in slowly extracted fashion over spill lengths of 1.5 to 4.0 seconds. Extraction is accomplished by flattoping the main and extraction magnets and exciting a third integer resonance in the AGS. Over the long spill times, control of the subharmonic amplitude components up to a frequency of 1 kilohertz is very crucial. One of the most critical contributions to spill modulation is due to the AGS MMPS. An active filter was developed to reduce these frequencies and it`s operation is described in a previous paper. However there are still frequency components in the 60-720 Hz sub-harmonic ripple range, modulating the spill structure due to extraction power supplies and any remaining structures on the AGS MMPS. A recent scheme is being developed to use the existing tune-trim control horizontal quadrupole magnets and power supply to further reduce these troublesome noise sources. Feedback from an external beam sensor and overcoming the limitations of the quadrupole system by lead/lag compensation techniques will be described.

  4. Particle beam injection system

    DOEpatents

    Jassby, Daniel L.; Kulsrud, Russell M.

    1977-01-01

    This invention provides a poloidal divertor for stacking counterstreaming ion beams to provide high intensity colliding beams. To this end, method and apparatus are provided that inject high energy, high velocity, ordered, atomic deuterium and tritium beams into a lower energy, toroidal, thermal equilibrium, neutral, target plasma column that is magnetically confined along an endless magnetic axis in a strong restoring force magnetic field having helical field lines to produce counterstreaming deuteron and triton beams that are received bent, stacked and transported along the endless axis, while a poloidal divertor removes thermal ions and electrons all along the axis to increase the density of the counterstreaming ion beams and the reaction products resulting therefrom. By balancing the stacking and removal, colliding, strong focused particle beams, reaction products and reactions are produced that convert one form of energy into another form of energy.

  5. Photonic crystal beam splitters.

    PubMed

    Chen, Chii-Chang; Chien, Hung-Da; Luan, Pi-Gang

    2004-11-20

    This work studies two-dimensional photonic crystal beam splitters with two input ports and two output ports. The beam splitter structure consists of two orthogonally crossed line defects and one point defect in square-lattice photonic crystals. The point defect is positioned at the intersection of the line defects to divide the input power into output ports. If the position and the size of the point defect are varied, the power of two output ports can be identical. The beam splitters can be used in photonic crystal Mach-Zehnder interferometers or switches. The simulation results show that a large bandwidth of the extinction ratio larger than 20 dB can be obtained while two beams are interfered in the beam splitters. This enables photonic crystal beam splitters to be used in fiber optic communication systems.

  6. Craft Stick Beams

    NASA Technical Reports Server (NTRS)

    Karplus, Alan K.

    1996-01-01

    The objective of this exercise is to provide a phenomenological 'hands-on' experience that shows how geometry can affect the load carrying capacity of a material used in construction, how different materials have different failure characteristics, and how construction affects the performance of a composite material. This will be accomplished by building beams of a single material and composite beams of a mixture of materials (popsicle sticks, fiberboard sheets, and tongue depressors); testing these layered beams to determine how and where they fail; and based on the failure analysis, designing a layered beam that will fail in a predicted manner. The students will learn the effects of lamination, adhesion, and geometry in layered beam construction on beam strength and failure location.

  7. KEKB beam instrumentation systems

    NASA Astrophysics Data System (ADS)

    Arinaga, M.; Flanagan, J.; Hiramatsu, S.; Ieiri, T.; Ikeda, H.; Ishii, H.; Kikutani, E.; Mimashi, T.; Mitsuhashi, T.; Mizuno, H.; Mori, K.; Tejima, M.; Tobiyama, M.

    2003-02-01

    For the stable high-luminosity operation and luminosity increase, the electron and positron storage rings of the KEK B-Factory (KEKB) is equipped with various beam instrumentations, which have been working well since the start of the commissioning in December, 1998. Details and performance of the beam-position monitor system based on the spectrum analysis using DSPs, the turn-by-turn BPM with four-dimensional function available for measurements of the individual bunch position, phase and intensity, the parametric beam-DCCTs designed so as to avoid the magnetic-core-selection problems for the parametric flux modulation, the bunch-by-bunch feedback system indispensable to suppress the strong multibunch instabilities in KEKB, the various optical beam diagnostic systems, such as synchrotron radiation interferometers for precise beam-size measurement, the tune meters, the bunch length monitors and the beam-loss monitors are described. Delicate machine tuning of KEKB is strongly supported by these instrumentations.

  8. Photon beam studies of magnetic materials

    NASA Astrophysics Data System (ADS)

    Lovesey, S. W.

    1994-06-01

    The past decade has seen a surge of activity in the use of photon beam techniques to study magnetic properties of materials. By and large, in this period the experimental work has been accomplished with beams produced by electron synchrotron facilities. To date, it is fair to say that the surge of activity is underpinned by improvements in instrument performance, enjoyed at synchrotron sources, rather than outstanding intellectual advances. In consequence, improvements in the intensity at the sample, and the provision of good beams of polarized photons, which enable polarization induced discrimination effects to be exploited as a means of increasing the signal-to-noise, are particularly significant in the use for magnetic studies of photon beam techniques.

  9. Hyperon beam physics

    SciTech Connect

    Cooper, P.S.

    1996-03-01

    This report reviews the present status and recent results in hyperon physics concentrating on results from high energy hyperon beam experiments performed at Fermilab over the past several years. The report focuses on hyperon production polarization, precision hyperon magnetic moment measurements and radiative decay studies. Modern charged hyperon beam experiments are characterized by {approx}100m long apparatus and hyperon beams with {gamma}{sub Y}{approx}100 and hyperon fluxes in the 1-100 kHz range.

  10. Resolving Two Beams in Beam Splitters with a Beam Position Monitor

    NASA Astrophysics Data System (ADS)

    Kurennoy, Sergey

    2002-04-01

    The beam transport system for the Advanced Hydrotest Facility (AHF) anticipates multiple beam splitters. Monitoring two transversely separated beams in a common beam pipe in the splitter sections imposes certain requirements on beam diagnostics for these sections. We explore a two-beam system in a generic beam monitor and study the feasibility of resolving the transverse positions of the two beams with one diagnostics device. Effects of unequal beam currents and of finite transverse sizes of the beams are explored analytically for both the ultra relativistic case and the long-wavelength limit.

  11. (Pulsed electron beam precharger)

    SciTech Connect

    Finney, W.C.; Shelton, W.N.

    1990-01-01

    This report discusses the following topics on electron beam guns: Precharger Modification; Installation of Charge vs. Radius Apparatus; High Concentration Aerosol Generation; and Data Acquisition and Analysis System.

  12. Power beaming options

    NASA Technical Reports Server (NTRS)

    Rather, John D. G.

    1989-01-01

    Some large scale power beaming applications are proposed for the purpose of stimulating research. The first proposal is for a combination of large phased arrays on the ground near power stations and passive reflectors in geostationary orbit. The systems would beam excess electrical power in microwave form to areas in need of electrical power. Another proposal is to build solar arrays in deserts and beam the energy around the world. Another proposal is to use lasers to beam energy from earth to orbiting spacecraft.

  13. ALEX neutral beam probe

    SciTech Connect

    Pourrezaei, K.

    1982-01-01

    A neutral beam probe capable of measuring plasma space potential in a fully 3-dimensional magnetic field geometry has been developed. This neutral beam was successfully used to measure an arc target plasma contained within the ALEX baseball magnetic coil. A computer simulation of the experiment was performed to refine the experimental design and to develop a numerical model for scaling the ALEX neutral beam probe to other cases of fully 3-dimensional magnetic field. Based on this scaling a 30 to 50 keV neutral cesium beam probe capable of measuring space potential in the thermal barrier region of TMX Upgrade was designed.

  14. Broad beam ion implanter

    DOEpatents

    Leung, K.N.

    1996-10-08

    An ion implantation device for creating a large diameter, homogeneous, ion beam is described, as well as a method for creating same, wherein the device is characterized by extraction of a diverging ion beam and its conversion by ion beam optics to an essentially parallel ion beam. The device comprises a plasma or ion source, an anode and exit aperture, an extraction electrode, a divergence-limiting electrode and an acceleration electrode, as well as the means for connecting a voltage supply to the electrodes. 6 figs.

  15. Broad beam ion implanter

    DOEpatents

    Leung, Ka-Ngo

    1996-01-01

    An ion implantation device for creating a large diameter, homogeneous, ion beam is described, as well as a method for creating same, wherein the device is characterized by extraction of a diverging ion beam and its conversion by ion beam optics to an essentially parallel ion beam. The device comprises a plasma or ion source, an anode and exit aperture, an extraction electrode, a divergence-limiting electrode and an acceleration electrode, as well as the means for connecting a voltage supply to the electrodes.

  16. Magnetic beam position monitor

    SciTech Connect

    Varfolomeev, A.A.; Ivanchenkov, S.N.; Khlebnikov, A.S.

    1995-12-31

    Many nondestructive beam position monitors are known. However, these devices can not be used for DC particle beam diagnostics. We investigated a method of beam diagnostics applicable for the operative control of DC high power e-beam inside closed waveguide. A design of the detector for determination of{open_quote} center of mass {close_quote} position of DC particle beam was developed. It was shown that the monitor can be used as a nondestructive method for the beam position control in resonators. Magnetic field of the particle beam outside a resonator is used. The detector consists of the steel yokes and magnetic field sensors. The sensors measure magnetic fluxes in the steel yokes fixed outside the resonator. When the particle beam changes its position, these magnetic fluxes also change. Beam displacement sensitivity of the monitor depends on the steel yoke dimensions. The detector sensitivity is equal to 1 Gauss/mm for the conditions adequate to the FOM-FEM project.

  17. Long-Range Beam-Beam Compensation in RHIC

    SciTech Connect

    Kim, Hyung Jin; Sen, Tanaji; Fischer, Wolfram; /Brookhaven

    2010-05-01

    In order to avoid the effects of long-range beam-beam interactions which produce beam blow-up and deteriorate beam life time, a compensation scheme with current carrying wires has been proposed. Two long-range beam-beam compensators were installed in RHIC rings in 2006. The effects of the compensators have been experimentally investigated. An indication was observed that the compensators are beneficial to beam life time in measurements performed in RHIC during 2009. In this paper, we report the effects of wire compensator on beam loss and emittance for proton-proton beams at collision energy.

  18. Computational challenges for beam-beam simulation for RHIC

    SciTech Connect

    Luo, Y.; Fischer, W.

    2010-10-01

    In this article we will review the computational challenges in the beam-beam simulation for the polarized proton run of the Relativistic Heavy Ion Collider (RHIC). The difficulties in our multi-particle and million turn tracking to calculate the proton beam lifetime and proton beam emittance growth due to head-on beam-beam interaction and head-on beam-beam compensation are presented and discussed. Solutions to obtain meaningful physics results from these trackings are proposed and tested. In the end we will present the progress in the benchmarking of the RHIC operational proton beam lifetime.

  19. BEAM SIMULATIONS USING VIRTUAL DIAGNOSTICS FOR THE DRIVER LINAC

    SciTech Connect

    R. C. York; X. Wu; Q. Zhao

    2011-12-21

    End-to-end beam simulations for the driver linac have shown that the design meets the necessary performance requirements including having adequate transverse and longitudinal acceptances. However, to achieve reliable operational performance, the development of appropriate beam diagnostic systems and control room procedures are crucial. With limited R&D funding, beam simulations provide a cost effective tool to evaluate candidate beam diagnostic systems and to provide a critical basis for developing early commissioning and later operational activities. We propose to perform beam dynamic studies and engineering analyses to define the requisite diagnostic systems of the driver linac and through simulation to develop and test commissioning and operational procedures.

  20. Electron beam curing of polymer matrix composites

    SciTech Connect

    Janke, C.J.; Wheeler, D.; Saunders, C.

    1998-01-08

    The purpose of the CRADA was to conduct research and development activities to better understand and utilize the electron beam PMC curing technology. This technology will be used to replace or supplement existing PMC thermal curing processes in Department of Energy (DOE) Defense Programs (DP) projects and American aircraft and aerospace industries. This effort involved Lockheed Martin Energy Systems, Inc./Lockheed Martin Energy Research Corp. (Contractor), Sandia National Laboratories, and ten industrial Participants including four major aircraft and aerospace companies, three advanced materials companies, and three electron beam processing organizations. The technical objective of the CRADA was to synthesize and/or modify high performance, electron beam curable materials that meet specific end-use application requirements. There were six tasks in this CRADA including: Electron beam materials development; Electron beam database development; Economic analysis; Low-cost Electron Beam tooling development; Electron beam curing systems integration; and Demonstration articles/prototype structures development. The contractor managed, participated and integrated all the tasks, and optimized the project efforts through the coordination, exchange, and dissemination of information to the project participants. Members of the Contractor team were also the principal inventors on several electron beam related patents and a 1997 R and D 100 Award winner on Electron-Beam-Curable Cationic Epoxy Resins. The CRADA achieved a major breakthrough for the composites industry by having successfully developed high-performance electron beam curable cationic epoxy resins for use in composites, adhesives, tooling compounds, potting compounds, syntactic foams, etc. UCB Chemicals, the world`s largest supplier of radiation-curable polymers, has acquired a license to produce and sell these resins worldwide.