Science.gov

Sample records for actual experimental results

  1. PDX experimental results

    SciTech Connect

    Meade, D.; Arunasalam, V.; Barnes, C.

    1981-01-01

    The main objectives of the Poloidal Divertor Experiment (PDX) are to: (1) determine the effectiveness of poloidal divertors in controlling impurities in high temperature plasmas, (2) use the poloidal divertor to provide clean plasmas for confinement and high beta studies, and (3) investigate the effect of cross-section shaping on plasma confinement and MHD properties. In this paper, we report the results obtained during initial divertor operation of the PDX.

  2. Are Africa's actual problems a result of overpopulation?

    PubMed

    Logie, D; Woodroffe, J

    1994-01-01

    After the lost decade of the 1980s, Africa seems to be mired in debt, ecological devastation, drought, and disease. Malnutrition claims the lives of 11,000 children each day, and exposure to disease is heightened by the fact that 2/3 of all Africans do not have access to clean water for cooking and drinking. Sub-Saharan African countries are currently spending 50% more on servicing their debt than on the health and education of their children and less now on health per capita than they did in 1980. Despite paying out more than US$ 1,300 billion between 1982 and 1990, debtor countries are now 61% more indebted than they were in 1982. The first step toward a solution is to reduce the outstanding debt burden. Debt relief initiatives have resulted in some short-term alleviation, but so far less than 3% of total African debt has been cancelled. The considerable amount of debt owed to the World Bank and International Monetary Fund, which now absorb 36% of total debt service payments, has not been addressed. Governed by immutable laws, they cannot currently forgive debt, they can only delay its repayment. A major problem with all debt reduction schemes has been that they are linked to adjustment programs. The USA's latest offer to cancel 50% of debt to the very poorest African countries is conditional on their acceptance of such programs. The second step is to make sure that adjustment programs put the needs and aspirations of the poor at the center of any planning. In the past few years, Unicef, Oxfam, Christian Aid, and other non-governmental organizations have called for such reforms. Though some change has taken place in the rhetoric of the World Bank, it is vital to maintain pressure to ensure that reforms are put into practice. PMID:12318727

  3. Are Africa's actual problems a result of overpopulation?

    PubMed

    Logie, D; Woodroffe, J

    1994-01-01

    After the lost decade of the 1980s, Africa seems to be mired in debt, ecological devastation, drought, and disease. Malnutrition claims the lives of 11,000 children each day, and exposure to disease is heightened by the fact that 2/3 of all Africans do not have access to clean water for cooking and drinking. Sub-Saharan African countries are currently spending 50% more on servicing their debt than on the health and education of their children and less now on health per capita than they did in 1980. Despite paying out more than US$ 1,300 billion between 1982 and 1990, debtor countries are now 61% more indebted than they were in 1982. The first step toward a solution is to reduce the outstanding debt burden. Debt relief initiatives have resulted in some short-term alleviation, but so far less than 3% of total African debt has been cancelled. The considerable amount of debt owed to the World Bank and International Monetary Fund, which now absorb 36% of total debt service payments, has not been addressed. Governed by immutable laws, they cannot currently forgive debt, they can only delay its repayment. A major problem with all debt reduction schemes has been that they are linked to adjustment programs. The USA's latest offer to cancel 50% of debt to the very poorest African countries is conditional on their acceptance of such programs. The second step is to make sure that adjustment programs put the needs and aspirations of the poor at the center of any planning. In the past few years, Unicef, Oxfam, Christian Aid, and other non-governmental organizations have called for such reforms. Though some change has taken place in the rhetoric of the World Bank, it is vital to maintain pressure to ensure that reforms are put into practice.

  4. CDF experimental results on diffraction

    SciTech Connect

    Gallinaro, Michele; /Rockefeller U.

    2009-04-01

    Experimental results on diffraction from the Fermilab Tevatron collider obtained by the CDF experiment are reviewed and compared. We report on the diffractive structure function obtained from dijet production in the range 0 < Q{sup 2} < 10,000 GeV{sup 2}, and on the |t| distribution in the region 0 < |t| < 1 GeV{sup 2} for both soft and hard diffractive events up to Q{sup 2} {approx} 4,500 GeV{sup 2}. Results on single diffractive W/Z production, forward jets, and central exclusive production of both dijets and diphotons are also presented.

  5. Majorana Thermosyphon Prototype Experimental Results

    SciTech Connect

    Fast, James E.; Reid, Douglas J.; Aguayo Navarrete, Estanislao

    2010-12-17

    Objective The Majorana demonstrator will operate at liquid Nitrogen temperatures to ensure optimal spectrometric performance of its High Purity Germanium (HPGe) detector modules. In order to transfer the heat load of the detector module, the Majorana demonstrator requires a cooling system that will maintain a stable liquid nitrogen temperature. This cooling system is required to transport the heat from the detector chamber outside the shield. One approach is to use the two phase liquid-gas equilibrium to ensure constant temperature. This cooling technique is used in a thermosyphon. The thermosyphon can be designed so the vaporization/condensing process transfers heat through the shield while maintaining a stable operating temperature. A prototype of such system has been built at PNNL. This document presents the experimental results of the prototype and evaluates the heat transfer performance of the system. The cool down time, temperature gradient in the thermosyphon, and heat transfer analysis are studied in this document with different heat load applied to the prototype.

  6. Pentaquarks: the latest experimental results

    SciTech Connect

    M. Battaglieri; R. De Vita; Valery Kubarovsky

    2006-01-01

    After the claim of the possible discovery of a pentaquark state, many experiments reported positive and negative results opening a discussion about the pentaquark existence. New experiments with high resolution and high statistics are needed in the reaction channels and for the kinematics of the positive results to solve the controversy. Jefferson Lab started a comprehensive program to search for pentaquark in photoproduction at threshold on proton and deuteron targets, collecting more than 10 times the existing statistics. The first experiment on the proton (g11) just finished to analyze the data, and the first results of the pentaquark search are reported here.

  7. Bridging the gap between empirical results, actual strategies, and developmental programs in soccer.

    PubMed

    Figueiredo, António J; Gonçalves, Carlos E; Tessitore, Antonio

    2014-05-01

    Being one of the most prominent globalized sports, soccer played at club, national, and continental levels has a relevant societal role. At present, the specific competencies, interests, and languages of the different actors involved in the selection, development, and support of long-lasting careers of players might limit opportunities for potential talented players. Unless the cultural environment of soccer resolves the gaps between empirical results and actual soccer strategies, scientific discussion relating to the effectiveness of talent selection and development remains limited. This commentary is intended to highlight the need for developmental programs to prepare soccer personnel for a transdisciplinary dialogue, which could foster a future development of this sport. Finally, in considering the wide soccer-related employment opportunities at local, national, and international levels, the need for a clear qualification framework is crucial. PMID:24755978

  8. Feedback Loop of Data Infilling Using Model Result of Actual Evapotranspiration from Satellites and Hydrological Model

    NASA Astrophysics Data System (ADS)

    Murdi Hartanto, Isnaeni; Alexandridis, Thomas K.; van Andel, Schalk Jan; Solomatine, Dimitri

    2014-05-01

    Using satellite data in a hydrological model has long been occurring in modelling of hydrological processes, as a source of low cost regular data. The methods range from using satellite products as direct input, model validation, and data assimilation. However, the satellite data frequently face the missing value problem, whether due to the cloud cover or the limited temporal coverage. The problem could seriously affect its usefulness in hydrological model, especially if the model uses it as direct input, so data infilling becomes one of the important parts in the whole modelling exercise. In this research, actual evapotranspiration product from satellite is directly used as input into a spatially distributed hydrological model, and validated by comparing the catchment's end discharge with measured data. The instantaneous actual evapotranspiration is estimated from MODIS satellite images using a variation of the energy balance model for land (SEBAL). The eight-day cumulative actual evapotranspiration is then obtained by a temporal integration that uses the reference evapotranspiration calculated from meteorological data [1]. However, the above method cannot fill in a cell if the cell is constantly having no-data value during the eight-day periods. The hydrological model requires full set of data without no-data cells, hence, the no-data cells in the satellite's evapotranspiration map need to be filled in. In order to fills the no-data cells, an output of hydrological model is used. The hydrological model is firstly run with reference evapotranspiration as input to calculate discharge and actual evapotranspiration. The no-data cells in the eight-day cumulative map from the satellite are then filled in with the output of the first run of hydrological model. The final data is then used as input in a hydrological model to calculate discharge, thus creating a loop. The method is applied in the case study of Rijnland, the Netherlands where in the winter, cloud cover is

  9. Forest Landowner Education Interests and Delivery Preferences: A Retrospective Look at Survey Results and Actual Participation

    ERIC Educational Resources Information Center

    Zobrist, Kevin W.; Rozance, Mary Ann

    2015-01-01

    This article presents survey data on education interests and delivery preferences of small forest landowners in Washington and compares it to actual program participation over 6 years. The survey was conducted in late 2007 to guide development and implementation of a Extension forestry program. The survey found broad interest across many topics…

  10. Numerical reconstruction of part of an actual blast-wave flow field to agree with available experimental data

    NASA Astrophysics Data System (ADS)

    Lau, S. C. M.; Gottlieb, J. J.

    1983-11-01

    A method of solution is presented and validated for the numerical reconstruction of a certain part of an actual blast-wave flow field of interest for planar, cylindrical and spherical explosions, away from the explosion source where the blast-wave has become sufficiently weak that real-gas effects are unimportant. This method involves, essentially, a trial-and-error process of constructing the best possible path of a fluid particle or equivalent piston at the upstream side of the flow field of interest such that the resulting flow field constructed numerically in front of the equivalent moving piston agrees as well as possible with all available although limited experimental data. The relatively new random-choice method was suitably modified to easily handle the numerical computations of the nonstationary flow in front of the moving piston. Finally, the present method is used to reconstruct the flow field for past TNT and ANFO explosions, for which the blast-wave amplitudes are less than about 1 MPa. These results are presented in convenient graphical and tabular form, scaled for the case of a 1-kg TNT surface explosion or its equivalent in a standard atmosphere, so that they can be utilized readily for different sized explosions at the same or other atmospheric conditions.

  11. Experimental study using infrared thermography on the convective heat transfer of a TGV brake disc in the actual environment

    NASA Astrophysics Data System (ADS)

    Siroux, Monica; Harmand, Souad; Desmet, Bernard

    2002-07-01

    We present an experimental identification of the local and mean Nusselt number from a rotating TGV brake disk model in the actual environment and exposed to an air flow parallel to the disk surface. This method is based on the use of a heated thermally thick disk combined with the technique of temperature measurement by infrared thermography. The local and mean convective heat transfer coefficient from the disk surface is identified by solving the steady state heat equation by a finite difference method using the experimental temperature distribution as boundary conditions. The experimental setup is constituted of a model disk with all the representative parts of the actual TGV brake system. The disk and its actual environment are inside a wind tunnel test section, so that the rotational disk speed and the air flow velocity can be varied. Tests were carried out for rotational speeds w between 325 and 2000 rpm (rotational Reynolds number Re between 88,500 and 545,000), and for an air flow velocity U ranging between 0 and 12 m(DOT)s-1 (air flow Reynolds number Re0 between 0 and 153,000).

  12. Experimental Results in DIS from Jefferson Laboratory

    SciTech Connect

    Sebastian Kuhn

    2009-10-01

    We are summarizing the experimental program of Jefferson Lab (Thomas Jefferson National Accelerator Facility in Newport News, VA) in deep inelastic electron scattering. We show recent results and discuss future plans for both the present 6 GeV era and the 12 GeV energy-upgraded facility.

  13. Planned versus actual outcomes as a result of animal feeding operation decisions for managing phosphorus.

    PubMed

    Cabot, Perry E; Nowak, Pete

    2005-01-01

    The paper explores how decisions made on animal feeding operations (AFOs) influence the management of manure and phosphorus. Variability among these decisions from operation to operation and from field to field can influence the validity of nutrient loss risk assessments. These assessments are based on assumptions that the decision outcomes regarding manure distribution will occur as they are planned. The discrepancy between planned versus actual outcomes in phosphorus management was explored on nine AFOs managing a contiguous set of 210 fields in south-central Wisconsin. A total of 2611 soil samples were collected and multiple interviews conducted to assign phosphorus index (PI) ratings to the fields. Spearman's rank correlation coefficients (r(S)) indicated that PI ratings were less sensitive to soil test phosphorus (STP) levels (r(S) = 0.378), universal soil loss equation (USLE) (r(S) = 0.261), ratings for chemical fertilizer application (r(S) = 0.185), and runoff class (r(S) = -0.089), and more sensitive to ratings for manure application (r(S) = 0.854). One-way ANOVA indicated that mean field STP levels were more homogenous than field PI ratings between AFOs. Kolmogorov-Smirnov (K-S) tests displayed several nonsignificant comparisons for cumulative distribution functions, S(x), of mean STP levels on AFO fields. On the other hand, the K-S tests of S(x) for PI ratings indicated that the majority of these S(x) functions were significantly different between AFOs at or greater than the 0.05 significance level. Interviews suggested multiple reasons for divergence between planned and actual outcomes in managing phosphorus, and that this divergence arises at the strategic, tactical, and operational levels of decision-making.

  14. Experimental study using infrared thermography on the convective heat transfer of a TGV brake disc in the actual environment

    NASA Astrophysics Data System (ADS)

    Siroux, Monica; Harmand, Souad; Desmet, Bernard

    2001-03-01

    Local and mean convective heat transfer from a rotating TGV brake disc model in the actual environment and submitted to an air flow parallel to the disc surface is studied experimentally in this paper. The experimental technique is based on the use of a heated thermally thick disc combined with the technique of temperature measurement by infrared thermography. The local convective heat transfer coefficient from the disc surface is identified by solving the steady state heat equation by finite difference method using the experimental temperature distribution as boundary conditions. These tests were carried out for rotational speed (omega) between 325 and 2000 rpm (rotational Reynolds number Re between 88500 and 545000) so as to obtain laminar and turbulent flow on the disc, and for air flow velocity U ranging between 0 and 12 m s-1 (air flow Reynolds number Re0 between 0 and 153000).

  15. Experimental results from the small isochronous ring

    SciTech Connect

    Eduard Pozdeyev

    2005-05-01

    The Small Isochronous Ring (SIR) is a compact, low-energy storage ring designed to investigate the beam dynamics of high-intensity isochronous cyclotrons and synchrotrons at the transition energy. The ring was developed at Michigan State University (MSU) and has been operational since December 2003. It stores 20 keV hydrogen beams with a peak current of 10-20 microamps for up to 200 turns. The transverse and longitudinal profiles of extracted bunches are measured with an accuracy of approximately 1 mm. The high accuracy of the measurements makes the experimental data attractive for validation of multi-particle space charge codes. The results obtained in the ring show a fast growth of the energy spread induced by the space charge forces. The energy spread growth is accompanied by a breakup of the beam bunches into separated clusters that are involved in the vortex motion specific to the isochronous regime. The experimental results presented in the paper show a remarkable agreement with simulations performed with the code CYCO. In this paper, we discuss specifics of space charge effects in the isochronous regime, present results of experiments in SIR, and conduct a detailed comparison of the experimental data with results of simulations.

  16. Microwave radiometry for humanitarian demining: experimental results

    NASA Astrophysics Data System (ADS)

    Johnson, Joel T.; Kim, Hyunjin; Wiggins, David R.; Cheon, Yonghun

    2002-08-01

    Previous modeling studies have indicated that a multi-frequency radiometer could prove advantageous for humanitarian demining due to the oscillatory patterns in brightness temperature versus frequency that would be observed in the presence of a sub-surface target. Initial experimental results are reported in this paper from a multi-frequency radiometer (MFRAD) system operating at 19 frequencies in the 2.1-6.5 GHz band. The basic design of MFRAD is reviewed, and the calibration and noise background removal procedures discussed. Experimental results with sub-surface metallic and styrofoam targets are then provided that demonstrate the predicted oscillatory behavior. An FFT-based detection algorithm is also described and applied to measured data. Further plans for experiments and tests with this system are also detailed.

  17. Experimental Results for Space-Wire-D

    NASA Astrophysics Data System (ADS)

    Parkes, Steve; Gibson, David; Ferrer, Albert

    2015-09-01

    SpaceWire-D is a deterministic extension to SpaceWire that uses time-division multiplexing to schedule traffic within time-slots. It allows a single SpaceWire network to be used for both time-critical avionics control applications and asynchronous payload data-handling simultaneously using existing SpaceWire technology. In this paper we describe the services of SpaceWire-D and present experimental results for each service.

  18. PDX experimental results in FY82

    SciTech Connect

    Kaye, S.M.; Bell, M.; Bol, K.; Bitter, M.; Buchenauer, D.; Budny, R.; Brau, K.; Crowley, T.; Davis, S.; Dylla, H.

    1983-08-01

    This report presents a detailed summary of the major experimental results of PDX in FY82 and represents the efforts of the entire PDX group. Topics covered include ..beta..-scaling and fishbone studies, fluctuations, disruptions, impurities and impurity transport, power handling, limiter conditioning, edge studies, plasma fueling, counter-injection, and diagnostic development. A less detailed version will appear as the FY82 PDX contribution to the PPPL Annual Report.

  19. [Formaldehyde determination in tobacco smoke--studies under experimental and actual conditions].

    PubMed

    Schaller, K H; Triebig, G; Beyer, B

    1989-11-01

    The estimation of an external exposure to formaldehyde in tobacco smoke requires a reliable analytical method. The gas chromatographic determination of formaldehyde shows in comparison to photometric methods a higher sensitivity and specificity. In the main stream smoke of various kinds of cigarettes the amount of formaldehyde vary between 3.4 micrograms to 8.8 micrograms/cigarette, this is equal to concentration between 2.3 to 6.1 ppm. In the air of lounges in hospitals formaldehyde concentrations up to 0.19 ppm can be detected after smoking of 15 cigarettes over a period of 1.5 h. In kindergartens without tobacco smoke the formaldehyde concentrations in air range from 0.005 to 0.01 ppm. The smoking of 30 cigarettes and one pipe in a non ventilated room over 1.5 h exceeded formaldehyde concentrations between 0.21 to 0.45 ppm. The concentration declines to 0.08 ppm within 2h after termination of smoking. The MAK-value of 0.5 ppm is not exceeded; in contrast to this the indoor limit of 0.1 ppm recommended by the German Bundesgesundheitsamt is exceeded in the vicinity of the smoker. The formaldehyde concentrations in tobacco smoke reported in the older literature can not be confirmed; this is due to the nonspecificity of the photometric methods. On the basis of our results can be concluded that the irritating effects of tobacco smoke to the mucous membranes are the result of the sum of irritating effects caused by several compounds and particles in the smoke and not only the impact of formaldehyde.

  20. Experimental evaluation of actual delivered dose using mega-voltage cone-beam CT and direct point dose measurement

    SciTech Connect

    Matsubara, Kana; Kohno, Ryosuke; Nishioka, Shie; Shibuya, Toshiyuki; Ariji, Takaki; Akimoto, Tetsuo; Saitoh, Hidetoshi

    2013-07-01

    Radiation therapy in patients is planned by using computed tomography (CT) images acquired before start of the treatment course. Here, tumor shrinkage or weight loss or both, which are common during the treatment course for patients with head-and-neck (H and N) cancer, causes unexpected differences from the plan, as well as dose uncertainty with the daily positional error of patients. For accurate clinical evaluation, it is essential to identify these anatomical changes and daily positional errors, as well as consequent dosimetric changes. To evaluate the actual delivered dose, the authors proposed direct dose measurement and dose calculation with mega-voltage cone-beam CT (MVCBCT). The purpose of the present study was to experimentally evaluate dose calculation by MVCBCT. Furthermore, actual delivered dose was evaluated directly with accurate phantom setup. Because MVCBCT has CT-number variation, even when the analyzed object has a uniform density, a specific and simple CT-number correction method was developed and applied for the H and N site of a RANDO phantom. Dose distributions were calculated with the corrected MVCBCT images of a cylindrical polymethyl methacrylate phantom. Treatment processes from planning to beam delivery were performed for the H and N site of the RANDO phantom. The image-guided radiation therapy procedure was utilized for the phantom setup to improve measurement reliability. The calculated dose in the RANDO phantom was compared to the measured dose obtained by metal-oxide-semiconductor field-effect transistor detectors. In the polymethyl methacrylate phantom, the calculated and measured doses agreed within about +3%. In the RANDO phantom, the dose difference was less than +5%. The calculated dose based on simulation-CT agreed with the measured dose within±3%, even in the region with a high dose gradient. The actual delivered dose was successfully determined by dose calculation with MVCBCT, and the point dose measurement with the image

  1. The Samarkand EAS installation and experimental results

    NASA Astrophysics Data System (ADS)

    Makhmudov, B. M.; Sirodzhev, N. S.; Alimov, T. A.; Aliev, N. A.; Kakhkharov, M. K.; Khamikov, N. Kh.; Vernov, S. N.; Khristiansen, G. B.

    1982-09-01

    The Samarkand University extensive-air-shower installation is briefly described, and experimental results obtained at this installation are discussed. It is shown that the spatial distribution of EAS Cerenkov emission at distances of 10-100 m from the EAS axis with respect to shape and absolute value given a purely protonic composition of the primary radiation can be made compatible with the scaling model only under the assumption of an anomalously sharp increase with energy of the cross section of the inelastic interactions of hadrons with atomic air nuclei. In addition, it is shown that the Xmax(E0) relationship (Xmax is the position of the maximum of an individual EAS) obtained at E0 exceeding 10 to the 17th eV on the basis of Yakutsk data does not contradict Samarkand data at E0 = 10 to the 16th eV.

  2. Wind Plant Capacity Credit Variations: A Comparison of Results Using Multiyear Actual and Simulated Wind-Speed Data

    SciTech Connect

    Milligan, M.

    1997-06-01

    Although it is widely recognized that variations in annual wind energy capture can be significant, it is not clear how significant this effect is on accurately calculating the capacity credit of a wind plant. An important question is raised concerning whether one year of wind data is representative of long-term patters. This report calculates the range of capacity credit measures based on 13 years of actual wind-speed data. The results are compared to those obtained with synthetic data sets that are based on one year of data. Although the use of synthetic data sets is a considerable improvement over single-estimate techniques, this report finds that the actual inter-annual variation in capacity credit is still understated by the synthetic data technique.

  3. Wind plant capacity credit variations: A comparison of results using multiyear actual and simulated wind-speed data

    SciTech Connect

    Milligan, M.R.

    1997-12-31

    Although it is widely recognized that variations in annual wind energy capture can be significant, it is not clear how significant this effect is on accurately calculating the capacity credit of a wind plant. An important question is raised concerning whether one year of wind data is representative of long-term patterns. This paper calculates the range of capacity credit measures based on 13 years of actual wind-speed data. The results are compared to those obtained with synthetic data sets that are based on one year of data. Although the use of synthetic data sets is a considerable improvement over single-estimate techniques, this paper finds that the actual inter-annual variation in capacity credit is still understated by the synthetic data technique.

  4. Wind Plant Capacity Credit Variations: A Comparison of Results Using Multiyear Actual and Simulated Wind-Speed Data

    SciTech Connect

    Milligan, Michael

    1997-06-01

    Although it is widely recognized that variations in annual wind energy capture can be significant, it is not clear how significant this effect is on accurately calculating the capacity credit of a wind plant. An important question is raised concerning whether one year of wind data is representative of long-term patterns. This paper calculates the range of capacity credit measures based on 13 years of actual wind-speed data. The results are compared to those obtained with synthetic data sets that are based on one year of data. Although the use of synthetic data sets is a considerable improvement over single-estimate techniques, this paper finds that the actual inter- annual variation in capacity credit is still understated by the synthetic data technique.

  5. Experimental Results for SimFuels

    SciTech Connect

    Buck, Edgar C.; Casella, Andrew M.; Skomurski, Frances N.; MacFarlan, Paul J.; Soderquist, Chuck Z.; Wittman, Richard S.; Mcnamara, Bruce K.

    2012-08-22

    Assessing the performance of Spent (or Used) Nuclear Fuel (UNF) in geological repository requires quantification of time-dependent phenomena that may influence its behavior on a time-scale up to millions of years. A high-level waste repository environment will be a dynamic redox system because of the time-dependent generation of radiolytic oxidants and reductants and the corrosion of Fe-bearing canister materials. One major difference between used fuel and natural analogues, including unirradiated UO2, is the intense radiolytic field. The radiation emitted by used fuel can produce radiolysis products in the presence of water vapor or a thin-film of water that may increase the waste form degradation rate and change radionuclide behavior. To study UNF, we have been working on producing synthetic UO2 ceramics, or SimFuels that can be used in testing and which will contain specific radionuclides or non-radioactive analogs so that we can test the impact of radiolysis on fuel corrosion without using actual spent fuel. Although, testing actual UNF would be ideal for understanding the long term behavior of UNF, it requires the use of hot cells and is extremely expensive. In this report, we discuss, factors influencing the preparation of SimFuels and the requirements for dopants to mimic the behavior of UNF. We have developed a reliable procedure for producing large grain UO2 at moderate temperatures. This process will be applied to a series of different formulations.

  6. Double-blind photo lineups using actual eyewitnesses: an experimental test of a sequential versus simultaneous lineup procedure.

    PubMed

    Wells, Gary L; Steblay, Nancy K; Dysart, Jennifer E

    2015-02-01

    Eyewitnesses (494) to actual crimes in 4 police jurisdictions were randomly assigned to view simultaneous or sequential photo lineups using laptop computers and double-blind administration. The sequential procedure used in the field experiment mimicked how it is conducted in actual practice (e.g., using a continuation rule, witness does not know how many photos are to be viewed, witnesses resolve any multiple identifications), which is not how most lab experiments have tested the sequential lineup. No significant differences emerged in rates of identifying lineup suspects (25% overall) but the sequential procedure produced a significantly lower rate (11%) of identifying known-innocent lineup fillers than did the simultaneous procedure (18%). The simultaneous/sequential pattern did not significantly interact with estimator variables and no lineup-position effects were observed for either the simultaneous or sequential procedures. Rates of nonidentification were not significantly different for simultaneous and sequential but nonidentifiers from the sequential procedure were more likely to use the "not sure" response option than were nonidentifiers from the simultaneous procedure. Among witnesses who made an identification, 36% (41% of simultaneous and 32% of sequential) identified a known-innocent filler rather than a suspect, indicating that eyewitness performance overall was very poor. The results suggest that the sequential procedure that is used in the field reduces the identification of known-innocent fillers, but the differences are relatively small. PMID:24933175

  7. Experimental results of the betatron sum resonance

    SciTech Connect

    Wang, Y.; Ball, M.; Brabson, B.

    1993-06-01

    The experimental observations of motion near the betatron sum resonance, {nu}{sub x} + 2{nu}{sub z} = 13, are presented. A fast quadrupole (Panofsky-style ferrite picture-frame magnet with a pulsed power supplier) producing a betatron tune shift of the order of 0.03 at rise time of 1 {mu}s was used. This quadrupole was used to produce betatron tunes which jumped past and then crossed back through a betatron sum resonance line. The beam response as function of initial betatron amplitudes were recorded turn by turn. The correlated growth of the action variables, J{sub x} and J{sub z}, was observed. The phase space plots in the resonance frame reveal the features of particle motion near the nonlinear sum resonance region.

  8. A critical review of RHIC experimental results

    NASA Astrophysics Data System (ADS)

    Trainor, Thomas A.

    2014-07-01

    The relativistic heavy-ion collider (RHIC) was constructed to achieve an asymptotic state of nuclear matter in heavy-ion collisions, a near-ideal gas of deconfined quarks and gluons denoted quark-gluon plasma or QGP. RHIC collisions are indeed very different from the hadronic processes observed at the Bevalac and AGS, but high-energy elementary-collision mechanisms are also non-hadronic. The two-component model (TCM) combines measured properties of elementary collisions with the Glauber eikonal model to provide an alternative asymptotic limit for A-A collisions. RHIC data have been interpreted to indicate formation of a strongly-coupled QGP (sQGP) or "perfect liquid". In this review, I consider the experimental evidence that seems to support such conclusions and alternative evidence that may conflict with those conclusions and suggest different interpretations.

  9. Experimental rotordynamic coefficient results for honeycomb seals

    NASA Technical Reports Server (NTRS)

    Elrod, David A.; Childs, Dara W.

    1988-01-01

    Test results (leakage and rotordynamic coefficients) are presented for seven honeycomb-stator smooth-rotor seals. Tests were carried out with air at rotor speeds up to 16,000 cpm and supply pressures up to 8.2 bars. Test results for the seven seals are compared, and the most stable configuration is identified based on the whirl frequency ratio. Results from tests of a smooth-rotor/smooth-stator seal, a teeth-on-stator labyrinth seal, and the most stable honeycomb seal are compared.

  10. The Humanoid Robot LOLA—Experimental Results

    NASA Astrophysics Data System (ADS)

    Favot, V.; Schwienbacher, M.; Buschmann, T.; Lohmeier, S.; Ulbrich, H.

    2010-09-01

    With the experience gathered during the development and construnction of the robot JOHNNIE, a new humanoid robot LOLA was built. Goal of this project is to realize a fast, human-like walking. Different aspects of this complex mechatronic system and the first experiments results are presented. The lightweight construction and the custom build multi-sensory joint drives with high torque brushless motors are introduced. The new decentralized electronic control/sensing network is also discuss as well as the simulation environment, the trajectory planning algorithm and the stabilizing walking control. Finally the first experiments result are presented.

  11. Anticipated and Actual Reactions to Receiving HIV Positive Results Through Self-Testing Among Gay and Bisexual Men

    PubMed Central

    Carballo-Diéguez, Alex; Ibitoye, Mobolaji; Frasca, Timothy; Brown, William; Balan, Iván

    2014-01-01

    We explored anticipated and actual reactions to receiving HIV positive results through self-testing with a diverse group of 84 gay and bisexual men in New York City. Grounded Theory was used to investigate these reactions in a two-phase study, one hypothetical, followed by a practical phase in which self-tests were distributed and used. Three major themes emerged when participants were asked about their anticipated reactions to an HIV positive self-test result: managing emotional distress, obtaining HIV medical care, and postponing sexual activity. When participants were asked about their anticipated reactions to a partner’s HIV positive self-test result, five themes emerged: provide emotional support; refrain from engaging in sex with casual partner; avoid high-risk sexual activity with both main and casual partners; seek medical services; and obtain a confirmatory test result. Although none of the participants tested positive, seven of their partners did. Participants provided emotional support and linked their partners to support services. The availability of HIV self-testing kits offers potential opportunities to tackle HIV infection among individuals with high-risk practices. PMID:24858480

  12. Experimental results on advanced rotary desiccant dehumidifiers

    SciTech Connect

    Bharathan, D; Parsons, J; Maclaine-cross, I

    1986-08-01

    The Solar Energy Research Institute (SERI) has developed the Cyclic Test Facility (CTF) to develop and validate analytical methods for evaluating and predicting the performance of advanced rotary dehumidifiers. This paper describes the CTF, the dehumidifiers tested at the CTF, and the analytical methods used. The results reported provide an engineering data base and a design tool for evaluating rotary dehumidifiers for desiccant cooling applications.

  13. Numerical taxonomy on data: Experimental results

    SciTech Connect

    Cohen, J.; Farach, M.

    1997-12-01

    The numerical taxonomy problems associated with most of the optimization criteria described above are NP - hard [3, 5, 1, 4]. In, the first positive result for numerical taxonomy was presented. They showed that if e is the distance to the closest tree metric under the L{sub {infinity}} norm. i.e., e = min{sub T} [L{sub {infinity}} (T-D)], then it is possible to construct a tree T such that L{sub {infinity}} (T-D) {le} 3e, that is, they gave a 3-approximation algorithm for this problem. We will refer to this algorithm as the Single Pivot (SP) heuristic.

  14. Experimental results for absolute cylindrical wavefront testing

    NASA Astrophysics Data System (ADS)

    Reardon, Patrick J.; Alatawi, Ayshah

    2014-09-01

    Applications for Cylindrical and near-cylindrical surfaces are ever-increasing. However, fabrication of high quality cylindrical surfaces is limited by the difficulty of accurate and affordable metrology. Absolute testing of such surfaces represents a challenge to the optical testing community as cylindrical reference wavefronts are difficult to produce. In this paper, preliminary results for a new method of absolute testing of cylindrical wavefronts are presented. The method is based on the merging of the random ball test method with the fiber optic reference test. The random ball test assumes a large number of interferograms of a good quality sphere with errors that are statistically distributed such that the average of the errors goes to zero. The fiber optic reference test utilizes a specially processed optical fiber to provide a clean high quality reference wave from an incident line focus from the cylindrical wave under test. By taking measurements at different rotation and translations of the fiber, an analogous procedure can be employed to determine the quality of the converging cylindrical wavefront with high accuracy. This paper presents and discusses the results of recent tests of this method using a null optic formed by a COTS cylindrical lens and a free-form polished corrector element.

  15. Experimental results on diffraction at CDF

    SciTech Connect

    Gallinaro, Michele; /Rockefeller U. /Lisbon, LIFEP

    2010-09-01

    Diffractive events are studied by means of identification of one or more rapidity gaps and/or a leading antiproton. Measurements of soft and hard diffractive processes have been performed at the Tevatron p{bar p} collider and presented. We report on the diffractive structure function obtained from dijet production in the range 0 < Q{sup 2} < 10,000 GeV{sup 2}, and on the |t| distribution in the region 0 < |t| < 1 GeV{sup 2} for both soft and hard diffractive events up to Q{sup 2} {approx} 4,500 GeV{sup 2}. Results on single diffractive W/Z production, forward jets, and central exclusive production of both dijets and Z-bosons are also presented.

  16. Evidence supporting primary prevention of cardiovascular diseases with statins: Gaps between updated clinical results and actual practice.

    PubMed

    Bruckert, Eric; Ferrières, Jean

    2014-03-01

    The use of pharmacological lipid-lowering intervention in individuals with hypercholesterolaemia and known cardiovascular disease or diabetes/chronic kidney disease is well established. Current European Society of Cardiology guidelines recommend immediate initiation of drugs in adjunct to lifestyle intervention in these patients at high or very high cardiovascular risk. In these clinical settings, statins are generally chosen as the first-choice drug intervention, in consideration of the robust evidence showing a reduction in all-cause mortality and major adverse cardiac events (MACE). In contrast, primary prevention with statins, even in the subset of patients at high-risk of cardiovascular events, is not well implemented. This might be related to a lack of public awareness regarding the actual risk associated with prolonged exposure to high concentrations of low-density lipoprotein cholesterol (LDL-C) and uncertainties in the clinical evidence coming from the earliest trials in this patient subset. However, recent observational studies suggest that lowering LDL-C earlier in life and for a longer duration can substantially decrease the burden of cardiovascular disease and mortality. Moreover, results from recent well-conducted large meta-analyses of randomized clinical trials showed that primary prevention with statins reduced all-cause mortality by 14% and MACE by > 20% - findings similar to those observed for the use of statins in secondary prevention. Recently published American Heart Association/American College of Cardiology guidelines on the treatment of blood cholesterol emphasize that primary prevention using high-dose statins in individuals with LDL-C ≥ 190 mg/dL induces a benefit in atherosclerotic cardiovascular risk reduction that clearly exceeds the potential for adverse effects. We aim in this review to discuss the new data that advocate the use of statins in primary prevention earlier and more frequently, putting the efficacy evidence into

  17. Perceived Need and Actual Usage of the Family Support Agreement in Rural China: Results from a Nationally Representative Survey

    ERIC Educational Resources Information Center

    Chou, Rita Jing-Ann

    2011-01-01

    Purpose: The Family Support Agreement (FSA) is a voluntary but legal contract between older parents and adult children on parental support in China. As the first comprehensive empirical study on the FSA, this study aims to understand the prevalence and covariates of older parents' perceived need and actual use of this agreement. Design and…

  18. Exposure to alcohol commercials in movie theaters affects actual alcohol consumption in young adult high weekly drinkers: an experimental study.

    PubMed

    Koordeman, Renske; Anschutz, Doeschka J; Engels, Rutger C M E

    2011-01-01

    The present pilot study examined the effects of alcohol commercials shown in movie theaters on the alcohol consumption of young adults who see these commercials. A two (alcohol commercials vs. nonalcohol commercials) by two (high weekly alcohol consumption vs. low weekly alcohol consumption) between-participant design was used, in which 184 young adults (age: 16-28 years) were exposed to a movie that was preceded by either alcohol commercials or nonalcohol commercials. Participants' actual alcohol consumption while watching the movie ("Watchmen") was examined. An analysis of variance (ANOVA) was conducted to examine the effects of the commercial condition on alcohol consumption. An interaction effect was found between commercial condition and weekly alcohol consumption (p < .001). Alcohol consumption among high weekly alcohol drinkers was higher in the alcohol commercial condition than in the nonalcohol commercial condition, whereas no differences were found in alcohol consumption between commercial conditions among low weekly alcohol drinkers. No gender differences were found in the association between exposure to alcohol commercials, weekly drinking, and alcohol use. Thus, exposure to alcohol commercials prior to a movie in a movie theater can directly influence alcohol consumption among high weekly alcohol consumers. PMID:21477057

  19. Exposure to alcohol commercials in movie theaters affects actual alcohol consumption in young adult high weekly drinkers: an experimental study.

    PubMed

    Koordeman, Renske; Anschutz, Doeschka J; Engels, Rutger C M E

    2011-01-01

    The present pilot study examined the effects of alcohol commercials shown in movie theaters on the alcohol consumption of young adults who see these commercials. A two (alcohol commercials vs. nonalcohol commercials) by two (high weekly alcohol consumption vs. low weekly alcohol consumption) between-participant design was used, in which 184 young adults (age: 16-28 years) were exposed to a movie that was preceded by either alcohol commercials or nonalcohol commercials. Participants' actual alcohol consumption while watching the movie ("Watchmen") was examined. An analysis of variance (ANOVA) was conducted to examine the effects of the commercial condition on alcohol consumption. An interaction effect was found between commercial condition and weekly alcohol consumption (p < .001). Alcohol consumption among high weekly alcohol drinkers was higher in the alcohol commercial condition than in the nonalcohol commercial condition, whereas no differences were found in alcohol consumption between commercial conditions among low weekly alcohol drinkers. No gender differences were found in the association between exposure to alcohol commercials, weekly drinking, and alcohol use. Thus, exposure to alcohol commercials prior to a movie in a movie theater can directly influence alcohol consumption among high weekly alcohol consumers.

  20. Experimental results for the interference between FM television signals

    NASA Technical Reports Server (NTRS)

    Groumpos, P. P.; Vernon, G. D.

    1981-01-01

    Experimental results based on subjective evaluation of picture quality of FM television systems are presented. Curves indicating the variation in protection ratio with impairment grade are provided. Such an analysis would be useful to the broadcasting satellite system designer. The experimental procedures and test conditions followed are briefly summarized. The need for a theoretical planning method is briefly discussed.

  1. Comparison of calculated and experimental results of fragmenting cylinder experiments

    SciTech Connect

    WILSON,L.T.; REEDAL,D.R.; KIPP,MARLIN E.; MARTINEZ,REINA R.; GRADY,D.E.

    2000-06-02

    The Grady-Kipp fragmentation model provides a physically based method for determining the fracture and breakup of materials under high loading rates. Recently, this model has been implemented into the CTH Shock Physics Code and has been used to simulate several published experiments. Materials studied in this paper are AerMet 100 steel and a 90% tungsten alloy. The experimental geometry consists of a right circular cylinder filled with an explosive main charge that is initiated at its center. The sudden expansion of the resulting detonation products causes fracture of the cylinder. Strain rates seen in the cylinder are on the order of 10{sup 4} s{sup {minus}1}. The average fragment sizes calculated with the Grady-Kipp fragmentation model successfully replicate the mean fragment size obtained from the experimental fragment distribution. When Poisson statistics are applied to the calculated local average fragment sizes, good correlation is also observed with the shape of the experimental cumulative fragment distribution. The experimental fragmentation results, CTH numerical simulations, and correlation of these numerical results with the experimental data are described.

  2. Comparing results from actual and virtual linear scanlines in fractured sandstones of the Marnoso-Arenacea Formation, Northern Apennines, Italy

    NASA Astrophysics Data System (ADS)

    Borsani, Angelo; Balsamo, Fabrizio; Bistacchi, Andrea; Ogata, Kei; Storti, Fabrizio; Fetter, Marcos

    2016-04-01

    Three-dimensional photogrammetric techniques arecommonly used to generate high-resolution digital outcrop models suitable to complement stratigraphic and structural field studies. This is particularly true for near vertical outcrops were direct data collection is very difficult to perform, provided that the data are reliable. To check whether fracture attribute data acquired from photogrammetric digital outcrop models can be effectively integrate field data, we performed a multisource data acquisition programme on the master joint set affecting the Langhian part of the Marnoso Arenacea Formation, a foredeep siliciclastic turbidite succession widely exposed in the external sector of the Northern Apennines. We selected an about 90 m high vertical cliff in a meander of the Santerno River, which was surveyed by both terrestrial and drone-aided photogrammetry to produce two different digital outcrop models of the same strata. Moreover, field data were collected in the same strata along river bed exposures few hundred meters upstream. Comparison of master joint attributes, namely orientation, spacing and height, collected along linear scanlines in the field and in the two digital outcrop models shows quite comparable results, particularly when FSI (Fracture Spacing Index) values are considered. Sensitivity tests of the impact of the number of data on the statistical results from photogrammetric scanlines, where hundreds of measurements can be collected along each scan line, were also performed. Our results provide further support to the effectiveness of the integration between field and photogrammetrically-obtained structural data to study fracture densities in partially accessible exposures. Given the large data numbers that can be collected in digital outcrop models, once validated in the field, photogrammetric data allow robust statistical analysis to be performed on fracture attributes.

  3. Design and experimental results for the S805 airfoil

    SciTech Connect

    Somers, D.M.

    1997-01-01

    An airfoil for horizontal-axis wind-turbine applications, the S805, has been designed and analyzed theoretically and verified experimentally in the low-turbulence wind tunnel of the Delft University of Technology Low Speed Laboratory, The Netherlands. The two primary objectives of restrained maximum lift, insensitive to roughness, and low profile drag have been achieved. The airfoil also exhibits a docile stall. Comparisons of the theoretical and experimental results show good agreement. Comparisons with other airfoils illustrate the restrained maximum lift coefficient as well as the lower profile-drag coefficients, thus confirming the achievement of the primary objectives.

  4. Design and experimental results for the S809 airfoil

    SciTech Connect

    Somers, D M

    1997-01-01

    A 21-percent-thick, laminar-flow airfoil, the S809, for horizontal-axis wind-turbine applications, has been designed and analyzed theoretically and verified experimentally in the low-turbulence wind tunnel of the Delft University of Technology Low Speed Laboratory, The Netherlands. The two primary objectives of restrained maximum lift, insensitive to roughness, and low profile drag have been achieved. The airfoil also exhibits a docile stall. Comparisons of the theoretical and experimental results show good agreement. Comparisons with other airfoils illustrate the restrained maximum lift coefficient as well as the lower profile-drag coefficients, thus confirming the achievement of the primary objectives.

  5. Experimental results for a hypersonic nozzle/afterbody flow field

    NASA Technical Reports Server (NTRS)

    Spaid, Frank W.; Keener, Earl R.; Hui, Frank C. L.

    1995-01-01

    This study was conducted to experimentally characterize the flow field created by the interaction of a single-expansion ramp-nozzle (SERN) flow with a hypersonic external stream. Data were obtained from a generic nozzle/afterbody model in the 3.5 Foot Hypersonic Wind Tunnel at the NASA Ames Research Center, in a cooperative experimental program involving Ames and McDonnell Douglas Aerospace. The model design and test planning were performed in close cooperation with members of the Ames computational fluid dynamics (CFD) team for the National Aerospace Plane (NASP) program. This paper presents experimental results consisting of oil-flow and shadow graph flow-visualization photographs, afterbody surface-pressure distributions, rake boundary-layer measurements, Preston-tube skin-friction measurements, and flow field surveys with five-hole and thermocouple probes. The probe data consist of impact pressure, flow direction, and total temperature profiles in the interaction flow field.

  6. Experimental results for correlation-based wavefront sensing

    SciTech Connect

    Poyneer, L A; Palmer, D W; LaFortune, K N; Bauman, B

    2005-07-01

    Correlation wave-front sensing can improve Adaptive Optics (AO) system performance in two keys areas. For point-source-based AO systems, Correlation is more accurate, more robust to changing conditions and provides lower noise than a centroiding algorithm. Experimental results from the Lick AO system and the SSHCL laser AO system confirm this. For remote imaging, Correlation enables the use of extended objects for wave-front sensing. Results from short horizontal-path experiments will show algorithm properties and requirements.

  7. Experimental overview of COMPASS and CLAS results on TMDs

    NASA Astrophysics Data System (ADS)

    Riedl, Caroline

    2016-03-01

    In the past years, distribution functions depending on the transverse momentum of partons in the nucleon (TMDs) have been intensely studied in spin physics. The TMDs represent one approach to disentangle the multi-dimensional structure of the nucleon. Correlations of the transverse spin of quarks with their transverse momentum can be observed by measuring spin azimuthal asymmetries. Experimental results from the COMPASS (CERN) and CLAS (Jefferson Laboratory) collaborations are presented and an outlook to upcoming measurements at these facilities is given.

  8. Conformal external radiotherapy of prostatic carcinoma: requirements and experimental results.

    PubMed

    Troccaz, J; Menguy, Y; Bolla, M; Cinquin, P; Vassal, P; Laieb, N; Desbat, L; Dusserre, A; Dal Soglio, S

    1993-11-01

    The aim of conformal radiotherapy is to deliver, with high precision, a specific dose (which may be a high dose) to a planning target volume, concurrently with irradiating as little as possible healthy tissue and organs at risk. Radiation therapy may suffer from a number of problems that result in both over- or under-sizing the irradiation fields, making over-rough simplifications of the irradiation ballistics and delivering an insufficient tumoral dose (to spare critical organs and reduce toxicity). One of these problems lies in the accurate positioning of the planning target volume with respect to the irradiation system, thence in the correct execution of the ballistics. In this paper, we describe a system aiming at achieving a higher overall accuracy in the delivery of prostatic boost for carcinoma of the prostate. The system is based on the use of ultrasonic images for measuring the actual position of the prostate just before irradiation. Since these images are registered with pre-operative (CT or MR) images, the position and orientation of the planning target volume is computed with respect to the irradiation system, and can be corrected accordingly. First experiments have been performed on dummies, and the results are discussed.

  9. Design and experimental results for the S814 airfoil

    SciTech Connect

    Somers, D.M.

    1997-01-01

    A 24-percent-thick airfoil, the S814, for the root region of a horizontal-axis wind-turbine blade has been designed and analyzed theoretically and verified experimentally in the low-turbulence wind tunnel of the Delft University of Technology Low Speed Laboratory, The Netherlands. The two primary objectives of high maximum lift, insensitive to roughness, and low profile drag have been achieved. The constraints on the pitching moment and the airfoil thickness have been satisfied. Comparisons of the theoretical and experimental results show good agreement with the exception of maximum lift which is overpredicted. Comparisons with other airfoils illustrate the higher maximum lift and the lower profile drag of the S814 airfoil, thus confirming the achievement of the objectives.

  10. On collisional disruption - Experimental results and scaling laws

    NASA Astrophysics Data System (ADS)

    Davis, D. R.; Ryan, E. V.

    1990-01-01

    Both homogeneous and inhomogeneous targets have been addressed by the present experimental consideration of the impact strengths, fragment sizes, and fragment velocities generated by cement mortar targets whose crushing strengths vary by an order of magnitude, upon impact of projectiles in the velocity range of 50-5700 m/sec. When combined with additional published data, dynamic impact strength is found to correlate with quasi-static material strengths for materials ranging in character from basalt to ice; two materials not following this trend, however, are weak mortar and clay targets. Values consistent with experimental results are obtainable with a simple scaling algorithm based on impact energy, material properties, and collisional strain rate.

  11. Experimental results: Pilot plant calcine dissolution and liquid feed stability

    SciTech Connect

    Herbst, R.S.; Fryer, D.S.; Brewer, K.N.; Johnson, C.K.; Todd, T.A.

    1995-02-01

    The dissolution of simulated Idaho Chemical Processing Plant pilot plant calcines, containing none of the radioactive actinides, lanthanides or fission products, was examined to evaluate the solubility of calcine matrix materials in acidic media. This study was a necessary precursor to dissolution and optimization experiments with actual radionuclide-containing calcines. The importance of temperature, nitric acid concentration, ratio of acid volume to calcine mass, and time on the amount, as a weight percentage of calcine dissolved, was evaluated. These parameters were studied for several representative pilot plant calcine types: (1) Run No. 74 Zirconia calcine; (2) Run No. 17 Zirconia/Sodium calcine; (3) Run No. 64 Zirconia/Sodium calcine; (3) Run No. 1027 Alumina calcine; and (4) Run No. 20 Alumina/Zirconia/Sodium calcine. Statistically designed experiments with the different pilot plant calcines indicated the effect of the studied process variables on the amount of calcine dissolved decreases in the order: Acid/Calcine Ratio > Temperature > HNO{sub 3} Concentration > Dissolution Time. The following conditions are suitable to achieve greater than 90 wt. % dissolution of most Zr, Al, or Na blend calcines: (1) Maximum nitric acid concentration of 5M; (2) Minimum acid/calcine ratio of 10 mL acid/1 gram calcine; (3) Minimum dissolution temperature of 90{degrees}C; and (4) Minimum dissolution time of 30 minutes. The formation of calcium sulphate (CaSO{sub 4}) precipitates was observed in certain dissolved calcine solutions during the dissolution experiments. Consequently, a study was initiated to evaluate if and under what conditions the resulting dissolved calcine solutions would be unstable with regards to precipitate formation. The results indicate that precipitate formation in the calcine solutions prepared under the above proposed dissolution conditions are not anticipated.

  12. Comparison of Calculated and Experimental Results for a Boiling/Condensing Experimental Facility

    SciTech Connect

    Carbajo, Juan J; McDuffee, Joel Lee; Felde, David K

    2016-01-01

    A new experimental facility for materials irradiation and testing at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) is being developed. Details of this facility have been presented before [1, 2]. A prototype of this facility, the Thermo-Syphon Test Loop (TSTL) has been built and experimental data have been obtained and analyzed [3, 4]. Pre-test calculations for this facility with the RELAP5-3D code [5] have been presented previously [6] as well as other calculations [7, 8] with the TRACE code [9]. The results of both codes were very different [7]. RELAP5-3D predicted much higher pressures and temperatures than TRACE. This paper compares calculated results with the TSTL experimental data.

  13. Comparison of computational and experimental results for a supercritical airfoil

    NASA Technical Reports Server (NTRS)

    Rivers, Melissa B.; Wahls, Richard A.

    1994-01-01

    A computational investigation was performed to study the flow over a supercritical airfoil model. Solutions were obtained for steady-state transonic flow conditions using a thin-layer Navier-Stokes flow solver. The results from this computational study were compared with time-averaged experimental data obtained over a wide Reynolds number range at transonic speeds in the Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons were made at a nominal Mach number of 0.72 and at Reynolds numbers ranging from 6 x 10(exp 6) to 35 x 10(exp 6).

  14. Experimental and simulational result multipactors in 112 MHz QWR injector

    SciTech Connect

    Xin, T.; Ben-Zvi, I.; Belomestnykh, S.; Brutus, J. C.; Skaritka, J.; Wu, Q.; Xiao, B.

    2015-05-03

    The first RF commissioning of 112 MHz QWR superconducting electron gun was done in late 2014. The coaxial Fundamental Power Coupler (FPC) and Cathode Stalk (stalk) were installed and tested for the first time. During this experiment, we observed several multipacting barriers at different gun voltage levels. The simulation work was done within the same range. The comparison between the experimental observation and the simulation results are presented in this paper. The observations during the test are consisted with the simulation predictions. We were able to overcome most of the multipacting barriers and reach 1.8 MV gun voltage under pulsed mode after several round of conditioning processes.

  15. Some results of experimental investigations of fire tornadoes

    NASA Astrophysics Data System (ADS)

    Grishin, A. M.; Reino, V. V.; Sazanovich, V. M.; Tsvyk, R. Sh.; Sherstobitov, M. V.

    2012-05-01

    Results of experimental investigations of liquid fuel combustion in the regime of a twisted jet (model of a fire tornado) are presented. To perform investigations, a stand equipped with measuring devices based on optical and thermal imaging methods has been developed and manufactured. Dependences of the geometrical characteristics, heat flux, combustion rate, and frequencies of maxima in the spectral function of the intensity fluctuations and in the centre of gravity of image of the laser beam that has passed through the tornado on the twist velocity are determined.

  16. Sheet Hydroforming Process Numerical Model Improvement Through Experimental Results Analysis

    NASA Astrophysics Data System (ADS)

    Gabriele, Papadia; Antonio, Del Prete; Alfredo, Anglani

    2010-06-01

    The increasing application of numerical simulation in metal forming field has helped engineers to solve problems one after another to manufacture a qualified formed product reducing the required time [1]. Accurate simulation results are fundamental for the tooling and the product designs. The wide application of numerical simulation is encouraging the development of highly accurate simulation procedures to meet industrial requirements. Many factors can influence the final simulation results and many studies have been carried out about materials [2], yield criteria [3] and plastic deformation [4,5], process parameters [6] and their optimization. In order to develop a reliable hydromechanical deep drawing (HDD) numerical model the authors have been worked out specific activities based on the evaluation of the effective stiffness of the blankholder structure [7]. In this paper after an appropriate tuning phase of the blankholder force distribution, the experimental activity has been taken into account to improve the accuracy of the numerical model. In the first phase, the effective capability of the blankholder structure to transfer the applied load given by hydraulic actuators to the blank has been explored. This phase ended with the definition of an appropriate subdivision of the blankholder active surface in order to take into account the effective pressure map obtained for the given loads configuration. In the second phase the numerical results obtained with the developed subdivision have been compared with the experimental data of the studied model. The numerical model has been then improved, finding the best solution for the blankholder force distribution.

  17. [Experimental Conditions and Reliability Analysis of Results of COD components].

    PubMed

    Li, Zhi-hua; Zhang, Yin; Han, Xing; Yu, Ke; Li, Ru-jia

    2015-10-01

    The present study attempts to use SF( OUR(max)/OUR(en)) instead of S(0)/X(0) as an index of optimal initial conditions for determination of COD components by means of respirometry, thereby simplifying the measuring process and the operation can be automated. Further, the ratio of COD consumed by the growth of biomass can be used for the reliability assessment of results. Experimental results show that, experimental conditions for obtaining good results as follows: (1) for samples that composed of a large amount of easily biodegradable components (e. g., synthetic wastewater made by sodium acetate), SF should be in the range of 2.8 to 5.3, and the ratio of COD consumed by growth of biomass should be less than 30%; (2) for samples that composed of both readily biodegradable and slowly biodegradable components (i. e., typical domestic wastewater), SF should be in the range of 5.8 to 6.4, and the ratio of COD consumed by growth of biomass should be less than 30%; (3) and for samples that composed of a large amount of slowly biodegradable industrial wastewater (i. e., landfill leachate), SF should be 15 or less, and the ratio of COD consumed by growth of biomass should be approximately 40%. Therefore, when respirometry is used for the determination of COD components, the optimal conditions in terms of SF increase with the complexity of carbon source.

  18. Electrical and thermal behavior of unsaturated soils: experimental results

    NASA Astrophysics Data System (ADS)

    Nouveau, Marie; Grandjean, Gilles; Leroy, Philippe; Philippe, Mickael; Hedri, Estelle; Boukcim, Hassan

    2016-05-01

    When soil is affected by a heat source, some of its properties are modified, and in particular, the electrical resistivity due to changes in water content. As a result, these changes affect the thermal properties of soil, i.e., its thermal conductivity and diffusivity. We experimentally examine the changes in electrical resistivity and thermal conductivity for four soils with different grain size distributions and clay content over a wide range of temperatures, from 20 to 100 °C. This temperature range corresponds to the thermal conditions in the vicinity of a buried high voltage cable or a geothermal system. Experiments were conducted at the field scale, at a geothermal test facility, and in the laboratory using geophysical devices and probing systems. The results show that the electrical resistivity decreases and the thermal conductivity increases with temperature up to a critical temperature depending on soil types. At this critical temperature, the air volume in the pore space increases with temperature, and the resulting electrical resistivity also increases. For higher temperatures , the thermal conductivity increases sharply with temperature up to a second temperature limit. Beyond it, the thermal conductivity drops drastically. This limit corresponds to the temperature at which most of the water evaporates from the soil pore space. Once the evaporation is completed, the thermal conductivity stabilizes. To explain these experimental results, we modeled the electrical resistivity variations with temperature and water content in the temperature range 20 - 100°C, showing that two critical temperatures influence the main processes occurring during heating at temperatures below 100 °C.

  19. Non-Shock Initiation Model for Explosive Families: Experimental Results

    NASA Astrophysics Data System (ADS)

    Anderson, M. U.; Todd, S. N.; Caipen, T. L.; Jensen, C. B.; Hughs, C. G.

    2009-12-01

    The "DaMaGe-Initiated-Reaction" (DMGIR) computational model has been developed to predict the response of high explosives to non-shock mechanical insults. The distinguishing feature of this model is the introduction of a damage variable, which relates the evolution of damage to the initiation of a reaction in the explosive, and its growth to detonation. Specifically designed experiments were used to study the initiation process of each explosive family with embedded shock sensors and optical diagnostics. The experimental portion of this model development began with a study of PBXN-5 to develop DMGIR model coefficients for the rigid plastic bonded family, followed by studies of the cast, and bulk-moldable explosive families. The experimental results show an initiation mechanism that is related to input energy and material damage, with well defined initiation thresholds for each explosive family. These initiation details will extend the predictive capability of the DMGIR model from the rigid family into the cast and bulk-moldable families.

  20. Non-shock initiation model for explosive families : experimental results.

    SciTech Connect

    Anderson, Mark U.; Jensen, Charles B.; Todd, Steven N.; Hugh, Chance G.; Caipen, Terry L.

    2010-03-01

    The 'DaMaGe-Initiated-Reaction' (DMGIR) computational model has been developed to predict the response of high explosives to non-shock mechanical insults. The distinguishing feature of this model is the introduction of a damage variable, which relates the evolution of damage to the initiation of a reaction in the explosive, and its growth to detonation. Specifically designed experiments were used to study the initiation process of each explosive family with embedded shock sensors and optical diagnostics. The experimental portion of this model development began with a study of PBXN-5 to develop DMGIR model coefficients for the rigid plastic bonded family, followed by studies of the cast, and bulk-moldable explosive families. The experimental results show an initiation mechanism that is related to input energy and material damage, with well defined initiation thresholds for each explosive family. These initiation details will extend the predictive capability of the DMGIR model from the rigid family into the cast and bulk-moldable families.

  1. Experimental results of the ATF in-line injection system

    SciTech Connect

    Wang, X.J.; Srinivasan-Rao, T.; Batchelor, K.

    1995-05-01

    The initial experimental results of the Brookhaven accelerator test facility (ATF) in-line injector is presented. The ATF in-line injector employed a full copper RF gun with a pair of solenoid magnets for emittance compensation. The maximum acceleration field of the RF gun was measured to be 130 MV/m. The electron yield from the copper cathode was maximized using p- polarized laser and the Schottky effect. The quantum efficiency under optimum conditions was measured to be 0.04%. The measured electron bunch length was less than 11 ps, which agreed with the laser pulse length measurement using a streak camera. The normalized rms. emittance for 0.25 nC charge is 0.9 {plus_minus} 0.1 mm-mrad, which is almost four times smaller than the emittance predicted by the space-charge effect for a non-emittance compensation photocathode RF gun. The normalized rms for 0.6 nC charge was measured range from 1 to 3 mm-mrad. This measurement was first experimental demonstration of emittance compensation in a high-gradient, S-band photocathode RF gun.

  2. Solving and Learning Soft Temporal Constraints: Experimental Setting and Results

    NASA Technical Reports Server (NTRS)

    Rossi, F.; Sperduti, A.; Venable, K. B.; Khatib, L.; Morris, P.; Morris, R.; Clancy, Daniel (Technical Monitor)

    2002-01-01

    Soft temporal constraints problems allow to describe in a natural way scenarios where events happen over time and preferences are associated to event distances and durations. However, sometimes such local preferences are difficult to set, and it may be easier instead to associate preferences to some complete solutions of the problem. Machine learning techniques can be useful in this respect. In this paper we describe two solvers (one more general and the other one more efficient) for tractable subclasses of soft temporal problems, and we show some experimental results. The random generator used to build the problems on which tests are performed is also described. We also compare the two solvers highlighting the tradeoff between performance and representational power. Finally, we present a learning module and we show its behavior on randomly-generated examples.

  3. Beta decay and the origins of biological chirality - Experimental results

    NASA Technical Reports Server (NTRS)

    Gidley, D. W.; Rich, A.; Van House, J.; Zitzewitz, P. W.

    1982-01-01

    Preliminary experimental results are presented of an investigation of the possible role of preferential radiolysis by electrons emitted in the beta decay of radionuclides, a parity-nonconserving process, in the universal causation of the optical activity of biological compounds. Experiments were designed to measure the asymmetry in the production of triplet positronium upon the bombardment of an amino acid powder target by a collimated beam of positrons as positron helicity or target chirality is reversed. No asymmetry down to a level of 0.0007 is found in experiments on the D and L forms of cystine and tryptophan, indicating an asymmetry in positronium formation cross section of less than 0.01, while an asymmetry of 0.0031 is found for leucine, corresponding to a formation cross section asymmetry of about 0.04

  4. Integrated radar-camera security system: experimental results

    NASA Astrophysics Data System (ADS)

    Zyczkowski, M.; Palka, N.; Trzcinski, T.; Dulski, R.; Kastek, M.; Trzaskawka, P.

    2011-06-01

    The nature of the recent military conflicts and terrorist attacks along with the necessity to protect bases, convoys and patrols have made a serious impact on the development of more effective security systems. Current widely-used perimeter protection systems with zone sensors will soon be replaced with multi-sensor systems. Multi-sensor systems can utilize day/night cameras, IR uncooled thermal cameras, and millimeter-wave radars which detect radiation reflected from targets. Ranges of detection, recognition and identification for all targets depend on the parameters of the sensors used and of the observed scene itself. In this paper two essential issues connected with multispectral systems are described. We will focus on describing the autonomous method of the system regarding object detection, tracking, identification, localization and alarm notifications. We will also present the possibility of configuring the system as a stationary, mobile or portable device as in our experimental results.

  5. Preliminary Experimental Results from a MARS Micro-CT System

    PubMed Central

    He, Peng; Yu, Hengyong; Thayer, Patrick; Jin, Xin; Xu, Qiong; Bennett, James; Tappenden, Rachael; Wei, Biao; Goldstein, Aaron; Renaud, Peter; Butler, Anthony; Butler, Phillip; Wang, Ge

    2013-01-01

    The Medipix All Resolution System (MARS) system is a commercial spectral/multi-energy micro-CT scanner designed and assembled by the MARS Bioimaging, Ltd. in New Zealand. This system utilizes the state-of-the-art Medipix photon-counting, energy-discriminating detector technology developed by a collaboration based at European Organization for Nuclear Research (CERN). In this paper, we report our preliminary experimental results using this system, including geometrical alignment, photon energy characterization, protocol optimization, and spectral image reconstruction. We produced our scan datasets with a multi-material phantom, and then applied ordered subset-simultaneous algebraic reconstruction technique (OS-SART) to reconstruct images in different energy ranges and principal component analysis (PCA) to evaluate spectral deviation between the energy ranges. PMID:22635175

  6. Physical mechanism of comet outbursts - An experimental result

    NASA Technical Reports Server (NTRS)

    Hartmann, William K.

    1993-01-01

    Attention is given to an experimental investigation of the physical mechanism of comet outbursts which is consistent with the general picture of mantle presence on comets and clarifies the relation of mantles to eruptive activity. The experiment and closeup observation of Comet P/Halley suggest a result different from most mathematical models in that the release of gas pressure does not occur only from uniform gas flow out of the entire surface. In some active comets near perihelion within a few AU of the sun, gas production rates and disturbance of the surface may be so high that the outflow is nearly continuous, with the regolith being entirely stripped away, as in many of the models. The present model provides a cyclic eruption and recharge mechanism which is lacking in most other models.

  7. Experimental results to study astrophysical plasma jets using Intense Lasers

    NASA Astrophysics Data System (ADS)

    Loupias, B.; Gregory, C. D.; Falize, E.; Waugh, J.; Seiichi, D.; Pikuz, S.; Kuramitsu, Y.; Ravasio, A.; Bouquet, S.; Michaut, C.; Barroso, P.; Rabec Le Gloahec, M.; Nazarov, W.; Takabe, H.; Sakawa, Y.; Woolsey, N.; Koenig, M.

    2009-08-01

    We present experimental results of plasma jet, interacted with an ambient medium, using intense lasers to investigate the complex features of astrophysical jets. This experiment was performed in France at the LULI facility, Ecole Polytechnique, using one long pulse laser to generate the jet and a short pulse laser to probe it by proton radiography. A foam filled cone target was used to generate high velocity plasma jet, and a gas jet nozzle produced the well known ambient medium. Using visible pyrometry and interferometry, we were able to measure the jet velocity and electronic density. We get a panel of measurements at various gas density and time delay. From these measurements, we could underline the growth of a perturbed shape of the jet interaction with the ambient medium. The reason of this last observation is still in debate and will be presented in the article.

  8. Arm-free paraplegic standing--Part II: Experimental results.

    PubMed

    Matjacić, Z; Bajd, T

    1998-06-01

    In Part I, we proposed an approach for restoring unsupported standing to thoracic-level paraplegics. The theoretical analysis and simulation of an underactuated double inverted pendulum, representing the standing subject, showed that arm-free standing might be achieved. Here in Part II, we present the mechanical apparatus which we used in our experiments and experimental results from tests of the balance-control strategy. We demonstrate that an intact and a paraplegic subject could perform quiet standing with the ankle stiffness set to 8 Nm/degree or even less (the intact subject). Both were also able to recover from disturbances, imposed by the artificial ankle joint of the apparatus. Introducing cognitive auditory feedback greatly improved the standing abilities of both subjects. PMID:9631321

  9. Selected experimental results from heavy-ion collisions at LHC

    DOE PAGES

    Singh, Ranbir; Kumar, Lokesh; Netrakanti, Pawan Kumar; Mohanty, Bedangadas

    2013-01-01

    We reviewmore » a subset of experimental results from the heavy-ion collisions at the Large Hadron Collider (LHC) facility at CERN. Excellent consistency is observed across all the experiments at the LHC (at center of mass energysNN=2.76 TeV) for the measurements such as charged particle multiplicity density, azimuthal anisotropy coefficients, and nuclear modification factor of charged hadrons. Comparison to similar measurements from the Relativistic Heavy Ion Collider (RHIC) at lower energy (sNN=200 GeV) suggests that the system formed at LHC has a higher energy density and larger system size and lives for a longer time. These measurements are compared to model calculations to obtain physical insights on the properties of matter created at the RHIC and LHC.« less

  10. Object impedance control for cooperative manipulation - Theory and experimental results

    NASA Technical Reports Server (NTRS)

    Schneider, Stanley A.; Cannon, Robert H., Jr.

    1989-01-01

    The dynamic control module being developed in the Dynamic and Strategic Control of Cooperative Manipulators (DASCCOM) project at the Stanford University Aerospace Robotics Laboratory is described. First, the cooperative manipulation problem is analyzed from a systems perspective, and the desirable features of a control system for cooperative manipulation are discussed. Next, a control policy is developed that enforces a controlled impedance not of the individual arm endpoints, but of the manipulated object itself. A parallel implementation for a multiprocessor system is presented. The controller fully compensates for the system dynamics and directly controls the object internal forces. Most importantly, it presents a simple, powerful, intuitive interface to the strategic controller. Experimental results for a dual two-link arm robotic system are presented to verify the controllers performance, for both free-motion slews and environmental contact.

  11. Object impedance control for cooperative manipulation - Theory and experimental results

    NASA Technical Reports Server (NTRS)

    Schneider, Stanley A.; Cannon, Robert H., Jr.

    1992-01-01

    This paper presents the dynamic control module of the Dynamic and Strategic Control of Cooperating Manipulators (DASCCOM) project at Stanford University's Aerospace Robotics Laboratory. First, the cooperative manipulation problem is analyzed from a systems perspective, and the desirable features of a control system for cooperative manipulation are discussed. Next, a control policy is developed that enforces a controlled impedance not of the individual arm endpoints, but of the manipulated object itself. A parallel implementation for a multiprocessor system is presented. The controller fully compensates for the system dynamics and directly controls the object internal forces. Most importantly, it presents a simple, powerful, intuitive interface to higher level strategic control modules. Experimental results from a dual two-link-arm robotic system are used to compare the object impedance controller with other strategies, both for free-motion slews and environmental contact.

  12. Experimental Progress and Results of a Visible Nulling Coronagraph

    NASA Technical Reports Server (NTRS)

    Samuele, Rocco; Wallace, J. Kent; Schmidtlin, Edouard; Shao, Mike; Levine, B. Martin; Fregoso, Santos

    2007-01-01

    The crux of visible exoplanet detection is overcoming significant star-planet contrast ratios on the order of 10(exp -7) to 10(exp -10)-at very small angular separations. We are developing an interferometric nulling coronagraph designed to achieve a 10(exp -6) contrast ratio at a working science bandpass of 20% visible light. Achieving large, broadband suppression requires a pseudo-achromatic phase flip, while maintaining a strict error budget. Recent results from our nulling interferometer testbed yield contrast ratios at the 1.05x10(exp -6) level, with a 15% visible bandpass. This result is at 65% of our final bandpass requirement, although limitations of our current configuration make major hardware changes essential to broadening the bandpass. We make the argument that broadening the bandpass should not necessarily adversely affect the null depth until beyond the 20% visible light level. Using the same setup we are able to reach monochromatic null depths of 1.11x10(exp -7) (?= 638 nm)averaged over three seconds. This paper will describe our experimental approach for achieving deep broadband nulls, as well as error considerations and limitations, and the most recent results for our nulling coronagraph testbed.

  13. Internal wave emission from baroclinic jets: experimental results

    NASA Astrophysics Data System (ADS)

    Borcia, Ion D.; Rodda, Costanza; Harlander, Uwe

    2016-04-01

    Large-scale balanced flows can spontaneously radiate meso-scale inertia-gravity waves (IGWs) and are thus in fact unbalanced. While flow-dependent parameterizations for the radiation of IGWs from orographic and convective sources do exist, the situation is less developed for spontaneously emitted IGWs. Observations identify increased IGW activity in the vicinity of jet exit regions. A direct interpretation of those based on geostrophic adjustment might be tempting. However, directly applying this concept to the parameterization of spontaneous imbalance is difficult since the dynamics itself is continuously re-establishing an unbalanced flow which then sheds imbalances by GW radiation. Examining spontaneous IGW emission in the atmosphere and validating parameterization schemes confronts the scientist with particular challenges. Due to its extreme complexity, GW emission will always be embedded in the interaction of a multitude of interdependent processes, many of which are hardly detectable from analysis or campaign data. The benefits of repeated and more detailed measurements, while representing the only source of information about the real atmosphere, are limited by the non-repeatability of an atmospheric situation. The same event never occurs twice. This argues for complementary laboratory experiments, which can provide a more focused dialogue between experiment and theory. Indeed, life cycles are also examined in rotating-annulus laboratory experiments. Thus, these experiments might form a useful empirical benchmark for theoretical and modeling work that is also independent of any sort of subgrid model. In addition, the more direct correspondence between experimental and model data and the data reproducibility makes lab experiments a powerful testbed for parameterizations. Here we show first results from a small rotating annulus experiments and we will further present our new experimental facility to study wave emission from jets and fronts.

  14. Recent experimental results of KSTAR RF heating and current drive

    SciTech Connect

    Wang, S. J. Kim, J.; Jeong, J. H.; Kim, H. J.; Joung, M.; Bae, Y. S.; Kwak, J. G.

    2015-12-10

    The overview of KSTAR activities on ICRH, LHCD and ECH/CD including the last experimental results and future plan aiming for long-pulse high-beta plasma will be presented. Recently we achieved reasonable coupling of ICRF power to H-mode plasma through several efforts to increase system reliability. Power balance will be discussed on this experiment. LHCD is still struggling in the low power regime. Review of antenna spectrum for the higher coupling in H-mode plasma will be tried. ECH/CD provides 41 sec, 0.8 MW of heating power to support high-performance long-pulse discharge. Also, 170 GHz ECH system is integrated with the Plasma Control System (PCS) for the feedback controlling of NTM. Status and plan of ECH/CD will be discussed. Finally, helicon current drive is being prepared for the next stage of KSTAR operation. The hardware preparation and the calculation results of helicon current drive in KSTAR plasma will be discussed.

  15. Thermal conductivity of packed beds of refractory particles: Experimental results

    SciTech Connect

    Fedina, I.; Litovsky, E.; Shapiro, M.; Shavit, A.

    1997-08-01

    Experimental data on thermal conductivity of packed beds composed from various refractory particles (corundum, silica, magnesia, baddeleyite, yttrium oxide, spinel) obtained in the temperature range 400--2,000 K in various gases are presented. It is found that thermal conductivity of a bed composed from crushed refractory particles may change after the first and subsequent heatings. This occurs as a result of smoothing of particle surfaces and decreasing of contact heat barrier resistances between the granules. The influence of smoothing is most significant for beds composed from particles with sizes below 2 mm. In polydisperse beds, containing micrometer-size particles, sintering processes were found to occur at temperatures above 1,600 K. This led to a sharp increase of the bed thermal conductivity. In regimes where sintering did not take place, decreasing of particle size resulted in a decrease of the effective thermal conductivity. This is attributed to the increased number of contacts between the particles and the scattering of thermal radiation.

  16. Theoretical and Experimental Results Regarding LENR/CF

    SciTech Connect

    Robert W. Bass; Wm. Stan Gleeson

    2000-11-12

    We challenge the predominant view that low-energy nuclear reactions (LENRs) are prohibited by standard quantum mechanics (QM). This view, supposedly based on standard nuclear theory, need not apply in condensed-matter environments. These considerations indicate that seemingly novel experimental evidence of rapid aneutronic bulk-process transmutation, at extraordinarily low-energy levels, in a simple electrochemical reactor, can occur. This explains: (a) induced rapid decay of radioactive thorium into stable nuclides, e.g., Cu and (b) resulting, anomalous distribution of Cu isotopes. We reexamine arguments of Peebles cited as evidence that standard QM 'forbids' cold fusion (CF). We note oversimplifications in those and present an alternative, more sophisticated calculation (see Bass, Refs. 3 through 8) demonstrating that conventional wisdom about impenetrability of the 'Coulomb barrier' fails as a result of periodic-order-induced resonance. We also examine empirical evidence. In three independent tests of an LENR electrolysis cell, using different I-V-T (current/voltage/time) protocols, the percentage of radiation reduction (RR) transmutation achieved {eta}=[23{percent}, 50{percent}, 83{percent}] versus expended energy E=[0.6535, 32.5, 74.6] (Watt-hours), obtained by numerical integration of recorded product I{center_dot}V for processing time T, provides near-perfect straight-line correlation: {eta}={alpha}{center_dot}E + {eta}{sub 0}, {alpha}=0.8105, {eta}{sub 0}=22.888, (0.65 < E < 0.75).

  17. Recent experimental results of KSTAR RF heating and current drive

    NASA Astrophysics Data System (ADS)

    Wang, S. J.; Kim, J.; Jeong, J. H.; Kim, H. J.; Joung, M.; Bae, Y. S.; Kwak, J. G.

    2015-12-01

    The overview of KSTAR activities on ICRH, LHCD and ECH/CD including the last experimental results and future plan aiming for long-pulse high-beta plasma will be presented. Recently we achieved reasonable coupling of ICRF power to H-mode plasma through several efforts to increase system reliability. Power balance will be discussed on this experiment. LHCD is still struggling in the low power regime. Review of antenna spectrum for the higher coupling in H-mode plasma will be tried. ECH/CD provides 41 sec, 0.8 MW of heating power to support high-performance long-pulse discharge. Also, 170 GHz ECH system is integrated with the Plasma Control System (PCS) for the feedback controlling of NTM. Status and plan of ECH/CD will be discussed. Finally, helicon current drive is being prepared for the next stage of KSTAR operation. The hardware preparation and the calculation results of helicon current drive in KSTAR plasma will be discussed.

  18. Multi-stage apodized pupil Lyot coronagraph experimental results

    NASA Astrophysics Data System (ADS)

    Abe, L.; Venet, M.; Enya, K.; Kataza, H.; Nakagawa, T.; Tamura, M.

    2008-07-01

    Prolate (Pupil) Apodized Lyot Coronagraphs (PPALC) are known to offer optimal performances for a Lyot-type Coronagraph configuration, i.e. with an opaque occulting focal mask. One additional benefit of PPALC is its possible use in a multi-stage configuration. In theory, the coronagraphic performance can be QN, where Q is the energy rejection factor of one stage (the first one), and N the number of stages. Several ground-based telescopes are considering PPALC as an option for their high-contrast instrumentation (e.g. Gemini/GPI, EELT/EPICS, Subaru HiCIAO). Although the PPALC suffers from several limitations, several works are currently focused on fabricating entrance pupil apodizers and trying to find ways to overcome chromatism issues. In this work, we present the first experimental results from Multi-Stage PPALC (MS-PPALC) that was done in the context of the Japanese space telescope SPICA coronagraph project. Our entrance pupil apodizers use small diameter High Energy Beam Sensitive glass (HEBS-glass) from Canyon Materials Inc. The current results show modest coronagraphic performance due to uncompensated phase aberrations inherent to HEBS-glass material. In addition, and due to these uncompensated phase aberrations, the present optical configuration is an altered version of the originally planned set-up. However, we can demonstrate the validity the MS-PPALC concept and compare it to numerical simulations.

  19. Recent experimental results and future plan in KSTAR

    NASA Astrophysics Data System (ADS)

    Kwak, Jong-Gu; Lee, Sang-Gon; Bae, Young-Sun; Park, Boung-Ho; Kim, Jin-Young; KSTAR Team

    2014-10-01

    In this talk, the recent results of KSTAR will be presented focusing on extention of operational boundary in long-pulse discharges and highlights in experimental physics. H-mode discharges has been sustained longer and the operational regime of plasma parameters has been significantly extended in terms of heating power and plasma current. The long-pulse operation is in accordance with ITER requirement, i.e., in ITER similar shape, low safety factor (q95 ~ 3) and normalized beta (~2.0) with real-time control of density and power. Both ELM suppression and mitigation are discovered in wide range of RMP coil configuration and the suppression window in the edge safety factor has extended from 6.5 to 3.9 indicating the strong impact of resonant component. Beside RMP ELM suppression, it is also investigated the effect of other techniques on ELMs, such as edge heating by ECH and cooling by SMBI. Detailed evaluation of error field (EF) has been performed by 4 segment compass scan by the internal coils and the measured level of intrinsic error field is an order of magnitude lower than other tokamaks. In addition to the above topics, it is summarized the recent results on rotation & transport physics, newly installed diagnostics, MHD and fast ion activities, followed by the near future plan.

  20. Experimental Results of Hydrate Reservoir Destabilization Through Heating

    NASA Astrophysics Data System (ADS)

    Leeman, J.; Hornbach, M. J.; Elwood-Madden, M.; Phelps, T. J.; Rawn, C. J.

    2011-12-01

    Gas clathrate reservoirs have been considered as possible sources of energy, as hazards to deep water drilling operations, and as contributors to global climate change. Clathrate destabilization may occur through depressurization of the reservoir, addition of chemical inhibitors, or heating the reservoir. Meso-scale heat conduction experiments were conducted in the Seafloor Process Simulator (SPS) at Oak Ridge National Laboratory in an attempt to apply experimental constraints to purely numerical models of heat transfer within a nearly isobaric reservoir. A column of saturated sediment was place inside the pressure vessel and pressurized to conditions sufficient to form methane clathrate at seafloor temperatures, while the system remained at room temperature (298K). Once pressurized, the temperature of the vessel was then lowered to approximately 275K, forming pore filling clathrate in the sediment column. Following hydrate formation, heat was supplied to the center of the clathrate reservoir through a hot fluid heat exchanger embedded in the sediment column to dissociate the methane hydrate. Relative changes in temperature within the hydrate-sediment column were monitored with a fiber optic quasi-distributed sensing system (DSS), along with temperature and pressure within the vessel headspace. Using the DSS Plotter analysis software, it was determined that an axis-symmetric section of clathrate was dissociated around the heat exchanger. Clathrate dissociation was accompanied by a small rise in vessel headspace pressure in addition to the expected thermal expansion of the headspace gas. The quantity of heat input to the system was calculated from the drop in fluid temperature as it flowed through the heat exchanger. Increased heat input resulted in an increase in the volume of hydrate dissociated. Clathrate rapidly reformed immediately upon the removal of the heat energy. A simple numerical model has been developed to simulate the heat flow in the system. Early

  1. Experimental Results of NWCF Run H4 Calcine Dissolution Studies Performed in FY-98 and -99

    SciTech Connect

    Garn, Troy Gerry; Herbst, Ronald Scott; Batcheller, Thomas Aquinas; Sierra, Tracy Laureena

    2001-08-01

    Dissolution experiments were performed on actual samples of NWCF Run H-4 radioactive calcine in fiscal years 1998 and 1999. Run H-4 is an aluminum/sodium blend calcine. Typical dissolution data indicates that between 90-95 wt% of H-4 calcine can be dissolved using 1gram of calcine per 10 mLs of 5-8M nitric acid at boiling temperature. Two liquid raffinate solutions composed of a WM-188/aluminum nitrate blend and a WM-185/aluminum nitrate blend were converted into calcine at the NWCF. Calcine made from each blend was collected and transferred to RAL for dissolution studies. The WM-188/aluminum nitrate blend calcine was dissolved with resultant solutions used as feed material for separation treatment experimentation. The WM-185/aluminum nitrate blend calcine dissolution testing was performed to determine compositional analyses of the dissolved solution and generate UDS for solid/liquid separation experiments. Analytical fusion techniques were then used to determine compositions of the solid calcine and UDS from dissolution. The results from each of these analyses were used to calculate elemental material balances around the dissolution process, validating the experimental data. This report contains all experimental data from dissolution experiments performed using both calcine blends.

  2. Ground coupled heat-pump-system experimental results

    NASA Astrophysics Data System (ADS)

    Metz, P. D.

    1983-06-01

    Since October 1980, a small house in Upton, Long Island, New York has been heated and cooled by a liquid source heat pump using a shallow serpentine earth coil as a heat source/sink. After a brief introduction and system description, system performance data are presented, for the winter of 1981-82 and the summer of 1982, followed by a discussion of these results. The experimental test house is a 104 m(2) (1120 ft(2)) 3 bedroom ranch of energy saving construction with a heating load of 7.8 x 10 to the 6th power J/0C-day (4.1 x 10 to the 3rd power Btu/0F-day). The heat pump used during most of the period reported on here is a commercially available water to air unit sized to just meet the building design heating load with no auxiliary heat. The earth coil contains 155 m (507 ft) of nominal 1-1/2 in. medium density polyethylene pipe, and is approximately 25% ethylene glycol in water, is employed to permit subfreezing earth coil operation. Two independent data acquisition systems, a datalogger microcomputer system backed up by a Btu meter, monitor the space conditioning system performance.

  3. Experimental results of the European HELINOISE aeroacoustic rotor test

    NASA Astrophysics Data System (ADS)

    Splettstoesser, W. R.; Niesl, G.; Cenedese, F.; Nitti, F.; Papanikas, D. G.

    1995-04-01

    In a cooperative research program between eight European partners, a 40% geometrically and dynamically scaled and highly instrumented model of the ECD (formerly MBB) BO 105 helicopter main rotor was tested in the open-jet anechoic test section of the German-Dutch Wind Tunnel (DNW) in the Netherlands. The primary objectives of this experimental study were to: (1) to improve the physical unsderstanding of the impulsive rotor noise sources by correlating blade pressure and acoustic character- istics, and (2) to provide an extensive airload and acoustic database for code validation purposes. Consequently, a compressive set of simultaneous acoustic and aerodynamic blade surface pressure data as well as blade dynamic and performance data were measured for the standard rotor with rectangular blade tips. In addition, initial quantitative information of the blade-vortex miss distance during blade-vortex interaction (BVI) was obtained. This paper describes the model and summarizes the aeroacoustic key results. The blade pressure chracteristics are examined to identify with the corresponding characteristics of the radiated sound pressure fields provide improved insight into the physics of the impulsive noise mechanisms. For descent flight, the strong change of BVI noise directivity and level with descent condition is illustrated, and the importance of the blade-vortex miss distance shown.

  4. Preliminary Experimental Result of Magnetic Reconnection in Laboratory Plasma

    NASA Astrophysics Data System (ADS)

    Zhang, S. B.; Xie, J. L.; Hu, G. H.; Li, H.; Huang, G. L.; Liu, W. D.

    2011-05-01

    Magnetic reconnection is one of the most important physical processes in astrophysical plasmas. Lots of theoretical works, numerical simulations and observations have been done. Some experimental programs have been activated to investigate the basic mechanisms of magnetic reconnection. In order to investigate the electron dynamic near the electron diffusion region in magnetic reconnection process, an upgrade is accomplished in the LMP (Linear magnetic plasmas) device at University of Science and Technology of China. The magnetic field of reconnection is produced by passing two identical currents axially through two copper plates. Magnetic field and parallel electric field are measured by magnetic probes and emissive probes, respectively. The existence of a large electric field related to the reconnection process is verified. The plasma is driven by electric field and magnetic field, so the magnetic reconnection appears. The magnitude of axial current is found to scale with the number of passing particles. In the configuration of current bars, passing particles are even more and our measured axial current is about 10 A. Magnetic flux doesn't pile up because of the parameter region in our case, which is consistent with the result of numerical simulation.

  5. Experimental results on V-M type pulse tube refrigerator

    NASA Astrophysics Data System (ADS)

    Dai, Wei; Matsubara, Yoichi; Kobayashi, Hisayasu

    2002-06-01

    This article mainly introduces experimental results on a new type pulse tube refrigerator named as V-M type pulse tube refrigerator. The main difference from Stirling type or G-M type pulse tube refrigerator is that thermal compressor similar to that of a V-M cryocooler is used instead of mechanical compressor. By using temperature difference between room temperature and liquid nitrogen, pressure wave with high to low pressure ratio around 1.2 is obtained. This pressure wave is used to generate cooling effect at the cold end. With a 20 K pre-cooler, this machine reaches lowest temperature 5.25 K by using helium 4 at 0.77 Hz, 19 bar charge pressure. DC flow plays an important role in our system. It not only influences the final obtainable lowest temperature, but also is used to increase cold end cool-down speed. Total volume of the V-M type pulse tube refrigerator is around 3.3 l. However, dead volume inside rotor housing occupies about 2.8 l and can be much reduced.

  6. Acoustic analysis in Mudejar-Gothic churches: experimental results.

    PubMed

    Galindo, Miguel; Zamarreño, Teófilo; Girón, Sara

    2005-05-01

    This paper describes the preliminary results of research work in acoustics, conducted in a set of 12 Mudejar-Gothic churches in the city of Seville in the south of Spain. Despite common architectural style, the churches feature individual characteristics and have volumes ranging from 3947 to 10 708 m3. Acoustic parameters were measured in unoccupied churches according to the ISO-3382 standard. An extensive experimental study was carried out using impulse response analysis through a maximum length sequence measurement system in each church. It covered aspects such as reverberation (reverberation times, early decay times), distribution of sound levels (sound strength); early to late sound energy parameters derived from the impulse responses (center time, clarity for speech, clarity, definition, lateral energy fraction), and speech intelligibility (rapid speech transmission index), which all take both spectral and spatial distribution into account. Background noise was also measured to obtain the NR indices. The study describes the acoustic field inside each temple and establishes a discussion for each one of the acoustic descriptors mentioned by using the theoretical models available and the principles of architectural acoustics. Analysis of the quality of the spaces for music and speech is carried out according to the most widespread criteria for auditoria. PMID:15957758

  7. Acoustic analysis in Mudejar-Gothic churches: experimental results.

    PubMed

    Galindo, Miguel; Zamarreño, Teófilo; Girón, Sara

    2005-05-01

    This paper describes the preliminary results of research work in acoustics, conducted in a set of 12 Mudejar-Gothic churches in the city of Seville in the south of Spain. Despite common architectural style, the churches feature individual characteristics and have volumes ranging from 3947 to 10 708 m3. Acoustic parameters were measured in unoccupied churches according to the ISO-3382 standard. An extensive experimental study was carried out using impulse response analysis through a maximum length sequence measurement system in each church. It covered aspects such as reverberation (reverberation times, early decay times), distribution of sound levels (sound strength); early to late sound energy parameters derived from the impulse responses (center time, clarity for speech, clarity, definition, lateral energy fraction), and speech intelligibility (rapid speech transmission index), which all take both spectral and spatial distribution into account. Background noise was also measured to obtain the NR indices. The study describes the acoustic field inside each temple and establishes a discussion for each one of the acoustic descriptors mentioned by using the theoretical models available and the principles of architectural acoustics. Analysis of the quality of the spaces for music and speech is carried out according to the most widespread criteria for auditoria.

  8. Acoustic analysis in Mudejar-Gothic churches: Experimental results

    NASA Astrophysics Data System (ADS)

    Galindo, Miguel; Zamarreño, Teófilo; Girón, Sara

    2005-05-01

    This paper describes the preliminary results of research work in acoustics, conducted in a set of 12 Mudejar-Gothic churches in the city of Seville in the south of Spain. Despite common architectural style, the churches feature individual characteristics and have volumes ranging from 3947 to 10 708 m3. Acoustic parameters were measured in unoccupied churches according to the ISO-3382 standard. An extensive experimental study was carried out using impulse response analysis through a maximum length sequence measurement system in each church. It covered aspects such as reverberation (reverberation times, early decay times), distribution of sound levels (sound strength); early to late sound energy parameters derived from the impulse responses (center time, clarity for speech, clarity, definition, lateral energy fraction), and speech intelligibility (rapid speech transmission index), which all take both spectral and spatial distribution into account. Background noise was also measured to obtain the NR indices. The study describes the acoustic field inside each temple and establishes a discussion for each one of the acoustic descriptors mentioned by using the theoretical models available and the principles of architectural acoustics. Analysis of the quality of the spaces for music and speech is carried out according to the most widespread criteria for auditoria. .

  9. Laboratory simulations of lidar returns from clouds: experimental and numerical results.

    PubMed

    Zaccanti, G; Bruscaglioni, P; Gurioli, M; Sansoni, P

    1993-03-20

    The experimental results of laboratory simulations of lidar returns from clouds are presented. Measurements were carried out on laboratory-scaled cloud models by using a picosecond laser and a streak-camera system. The turbid structures simulating clouds were suspensions of polystyrene spheres in water. The geometrical situation was similar to that of an actual lidar sounding a cloud 1000 m distant and with a thickness of 300 m. Measurements were repeated for different concentrations and different sizes of spheres. The results show how the effect of multiple scattering depends on the scattering coefficient and on the phase function of the diffusers. The depolarization introduced by multiple scattering was also investigated. The results were also compared with numerical results obtained by Monte Carlo simulations. Substantially good agreement between numerical and experimental results was found. The measurements showed the adequacy of modern electro-optical systems to study the features of multiple-scattering effects on lidar echoes from atmosphere or ocean by means of experiments on well-controlled laboratory-scaled models. This adequacy provides the possibility of studying the influence of different effects in the laboratory in well-controlled situations.

  10. ICPP: Experimental Results from the Advanced Stellarator W7-AS

    NASA Astrophysics Data System (ADS)

    Jaenicke, Rolf

    2000-10-01

    As W7-AS resumes operation after almost a one year shutdown, it is opportune to review experimental results obtained until now. The most important goal as an advanced or partly optimized stellarator was to check some elements of the optimization scheme developed for the largely optimized W7-X presently being built in Greifswald in northern Germany. This optimization stratagem, which covers almost all aspects important for a fusion reactor, was implemented on W7-AS in only one key area - the reduction of Pfirsch-Schlueter currents, which is observable in the concurrent reduction of the Shafranov shift. The reduced Shafranov shift is important in high beta discharges where average beta values of 2Reduced Pfirsch-Schlueter currents also improve the neoclassical transport, which can be very large at high temperatures in 3D magnetic field configurations. It could be demonstrated that the 3D DKES code, taking into account trapped particle effects, can describe the experimental observations very well in cases where neoclassical transport dominates. Thus, predictions for W7-X, where neoclassical transport must be strongly diminished, should be reliable. Another aim of W7-X is to keep all pressure driven currents as small as possible in order not to perturb the optimized magnetic field configuration. In contrast, W7-AS also allows operation with large toroidal currents. The bootstrap current is large or tokamak-like and can be further enhanced by means of the ohmic heating transformer. Therefore, the stability behavior for finite toroidal currents in the presence of external poloidal fields has been a subject of investigation. Resumption of operation in the summer of 2000 is accompanied by two major modifications. The (previously counter) tangential neutral beam injector box has been shifted to a co-position, leading to an augmented heating efficiency at low magnetic fields and at high densities. Thus, higher beta values should be accessible, offering another chance to test

  11. Energy-resolved computed tomography: first experimental results

    NASA Astrophysics Data System (ADS)

    Shikhaliev, Polad M.

    2008-10-01

    First experimental results with energy-resolved computed tomography (CT) are reported. The contrast-to-noise ratio (CNR) in CT has been improved with x-ray energy weighting for the first time. Further, x-ray energy weighting improved the CNR in material decomposition CT when applied to CT projections prior to dual-energy subtraction. The existing CT systems use an energy (charge) integrating x-ray detector that provides a signal proportional to the energy of the x-ray photon. Thus, the x-ray photons with lower energies are scored less than those with higher energies. This underestimates contribution of lower energy photons that would provide higher contrast. The highest CNR can be achieved if the x-ray photons are scored by a factor that would increase as the x-ray energy decreases. This could be performed by detecting each x-ray photon separately and measuring its energy. The energy selective CT data could then be saved, and any weighting factor could be applied digitally to a detected x-ray photon. The CT system includes a photon counting detector with linear arrays of pixels made from cadmium zinc telluride (CZT) semiconductor. A cylindrical phantom with 10.2 cm diameter made from tissue-equivalent material was used for CT imaging. The phantom included contrast elements representing calcifications, iodine, adipose and glandular tissue. The x-ray tube voltage was 120 kVp. The energy selective CT data were acquired, and used to generate energy-weighted and material-selective CT images. The energy-weighted and material decomposition CT images were generated using a single CT scan at a fixed x-ray tube voltage. For material decomposition the x-ray spectrum was digitally spilt into low- and high-energy parts and dual-energy subtraction was applied. The x-ray energy weighting resulted in CNR improvement of calcifications and iodine by a factor of 1.40 and 1.63, respectively, as compared to conventional charge integrating CT. The x-ray energy weighting was also applied

  12. Can plumes collapse?: Experimental results and applications to Iceland.

    NASA Astrophysics Data System (ADS)

    Pears, M.; Lithgow-Bertelloni, C.

    2012-04-01

    Iceland has produced magma in a series of episodic events. From lava chemistry it has been inferred that the plume temperature decreased over the first 5 Myr by ~50°C and for the next 3 Myr following continental break up it continued to oscillate by ~25°C. Such data has been used to infer possible episodic collapse of the Iceland plume. Collapsing plumes are not common fluid dynamical features. In thermochemical plumes it is possible to achieve collapse by varying the relative buoyancy due to chemistry and due to temperature. In thermal plumes however, with a constant heat source we would expect plumes not to collapse but to not continue to rise after reaching a point of neutral buoyancy. We expect thermal plumes, like those Earth's bottom thermal boundary layer is capable of producing, to either rise to the surface or be deflected but not to collapse. We have designed an experimental setup to investigate the conditions that may lead to collapse in thermal plumes with constant heat sources. We used high-Prandtl number fluids with strongly temperature-dependent viscosities (Lyle Golden syrup and Liquidose 436) as analogues to Earth's high viscosity mantle in a cubic Plexiglas tank (26.5cm inner sides), heated by a circular 2cm diameter heater (flat with the base of the tank). We explored ΔTs between 3-60°C. The flow was visualized with shadowgraphs and an automated -3D Stereoscopic Particle Image Velocimetry (SPIV) system to measure velocities. In Lyle's Golden Syrup collapse occurred at ΔTs as high as 8°C, while in Liquidose 436 the 8°C ΔT run showed only partial collapse. The difference is not unexpected given the different physical properties. Partial collapse was seen even for ΔTs as high as 50°C. Both complete and partial collapse manifested themselves as downwelling flow in the central part of the conduit. Collapse stopped in the hotter plumes when the downwelling fluid met the hottest part of the conduit. The observed results suggest that diffusive

  13. Can plumes collapse?: Experimental results and applications to Iceland

    NASA Astrophysics Data System (ADS)

    Pears, M.; Lithgow-Bertelloni, C. R.

    2011-12-01

    Iceland has produced magma in a series of episodic events. From lava chemistry it has been inferred that the plume temperature decreased over the first 5 Myr by ~50°C and for the next 3 Myr following continental break up it continued to oscillate by ~25°C. Such data has been used to infer possible episodic collapse of the Iceland plume. Collapsing plumes are not common fluid dynamical features. In thermochemical plumes it is possible to achieve collapse by varying the relative buoyancy due to chemistry and due to temperature. In thermal plumes however, with a constant heat source we would expect plumes not to collapse but to not continue to rise after reaching a point of neutral buoyancy. We expect thermal plumes, like those Earth's bottom thermal boundary layer is capable of producing, to either rise to the surface or be deflected but not to collapse. We have designed an experimental setup to investigate the conditions that may lead to collapse in thermal plumes with constant heat sources. We used high-Prandtl number fluids with strongly temperature-dependent viscosities (Lyle Golden syrup and Liquidose 436) as analogues to Earth's high viscosity mantle in a cubic Plexiglas tank (26.5cm inner sides), heated by a circular 2cm diameter heater (flat with the base of the tank). We explored ΔTs between 3-60°C. The flow was visualized with shadowgraphs and an automated -3D Stereoscopic Particle Image Velocimetry (SPIV) system to measure velocities. In Lyle's Golden Syrup collapse occurred at ΔTs as high as 8°C, while in Liquidose 436 the 8° ΔT run showed only partial collapse. The difference is not unexpected given the different physical properties. Partial collapse was seen even for ΔTs as high as 50°C. Both complete and partial collapse manifested themselves as downwelling flow in the central part of the conduit. Collapse stopped in the hotter plumes when the downwelling fluid met the hottest part of the conduit. The observed results suggest that diffusive

  14. Experimental subarachnoid haemorrhage results in multifocal axonal injury.

    PubMed

    Kummer, Terrance T; Magnoni, Sandra; MacDonald, Christine L; Dikranian, Krikor; Milner, Eric; Sorrell, James; Conte, Valeria; Benetatos, Joey J; Zipfel, Gregory J; Brody, David L

    2015-09-01

    The great majority of acute brain injury results from trauma or from disorders of the cerebrovasculature, i.e. ischaemic stroke or haemorrhage. These injuries are characterized by an initial insult that triggers a cascade of injurious cellular processes. The nature of these processes in spontaneous intracranial haemorrhage is poorly understood. Subarachnoid haemorrhage, a particularly deadly form of intracranial haemorrhage, shares key pathophysiological features with traumatic brain injury including exposure to a sudden pressure pulse. Here we provide evidence that axonal injury, a signature characteristic of traumatic brain injury, is also a prominent feature of experimental subarachnoid haemorrhage. Using histological markers of membrane disruption and cytoskeletal injury validated in analyses of traumatic brain injury, we show that axonal injury also occurs following subarachnoid haemorrhage in an animal model. Consistent with the higher prevalence of global as opposed to focal deficits after subarachnoid haemorrhage and traumatic brain injury in humans, axonal injury in this model is observed in a multifocal pattern not limited to the immediate vicinity of the ruptured artery. Ultrastructural analysis further reveals characteristic axonal membrane and cytoskeletal changes similar to those associated with traumatic axonal injury. Diffusion tensor imaging, a translational imaging technique previously validated in traumatic axonal injury, from these same specimens demonstrates decrements in anisotropy that correlate with histological axonal injury and functional outcomes. These radiological indicators identify a fibre orientation-dependent gradient of axonal injury consistent with a barotraumatic mechanism. Although traumatic and haemorrhagic acute brain injury are generally considered separately, these data suggest that a signature pathology of traumatic brain injury-axonal injury-is also a functionally significant feature of subarachnoid haemorrhage, raising

  15. Experimental subarachnoid haemorrhage results in multifocal axonal injury

    PubMed Central

    Magnoni, Sandra; MacDonald, Christine L.; Dikranian, Krikor; Milner, Eric; Sorrell, James; Conte, Valeria; Benetatos, Joey J.; Zipfel, Gregory J.; Brody, David L.

    2015-01-01

    The great majority of acute brain injury results from trauma or from disorders of the cerebrovasculature, i.e. ischaemic stroke or haemorrhage. These injuries are characterized by an initial insult that triggers a cascade of injurious cellular processes. The nature of these processes in spontaneous intracranial haemorrhage is poorly understood. Subarachnoid haemorrhage, a particularly deadly form of intracranial haemorrhage, shares key pathophysiological features with traumatic brain injury including exposure to a sudden pressure pulse. Here we provide evidence that axonal injury, a signature characteristic of traumatic brain injury, is also a prominent feature of experimental subarachnoid haemorrhage. Using histological markers of membrane disruption and cytoskeletal injury validated in analyses of traumatic brain injury, we show that axonal injury also occurs following subarachnoid haemorrhage in an animal model. Consistent with the higher prevalence of global as opposed to focal deficits after subarachnoid haemorrhage and traumatic brain injury in humans, axonal injury in this model is observed in a multifocal pattern not limited to the immediate vicinity of the ruptured artery. Ultrastructural analysis further reveals characteristic axonal membrane and cytoskeletal changes similar to those associated with traumatic axonal injury. Diffusion tensor imaging, a translational imaging technique previously validated in traumatic axonal injury, from these same specimens demonstrates decrements in anisotropy that correlate with histological axonal injury and functional outcomes. These radiological indicators identify a fibre orientation-dependent gradient of axonal injury consistent with a barotraumatic mechanism. Although traumatic and haemorrhagic acute brain injury are generally considered separately, these data suggest that a signature pathology of traumatic brain injury—axonal injury—is also a functionally significant feature of subarachnoid haemorrhage

  16. Bolus-tracking arterial spin labelling: theoretical and experimental results

    NASA Astrophysics Data System (ADS)

    Kelly, M. E.; Blau, C. W.; Kerskens, C. M.

    2009-03-01

    Arterial spin labelling (ASL) is a magnetic resonance imaging (MRI) technique that can be used to provide a quantitative assessment of cerebral perfusion. Despite the development of a number of theoretical models to facilitate quantitative ASL, some key challenges still remain. The purpose of this study is to develop a novel quantitative ASL method based on a macroscopic model that reduces the number of variables required to describe the physiological processes involved. To this end, a novel Fokker-Planck equation consisting of stochastically varying macroscopic variables was derived from a general Langevin equation. ASL data from the rat brain was acquired using a bolus-tracking ASL protocol where a bolus of labelled spins flowing from an inversion plane in the neck into an imaging plane in the brain can be observed. Bolus durations of 1.5 s, 2.0 s and 3.0 s were used and the solution to the Fokker-Planck equation for the boundary conditions of bolus-tracking ASL was fitted to the experimental data using a least-squares fit. The mean transit time (MTT) and capillary transit time (CTT) were calculated from the first and second moments of the resultant curve respectively and the arterial transit time (ATT) was calculated by subtracting the CTT from the MTT. The average MTT, CTT and ATT values were 1.75 ± 0.22 s, 1.43 ± 0.12 s and 0.32 ± 0.04 s respectively. In conclusion, a new ASL protocol has been developed by combining the theoretical model with ASL experiments. The technique has the unique ability to provide solutions for varying bolus volumes and the generality of the new model is demonstrated by the derivation of additional solutions for the continuous and pulsed ASL (CASL and PASL) techniques.

  17. Experimental Results on Jets in pA

    NASA Astrophysics Data System (ADS)

    Appelt, Eric

    2015-04-01

    The experimentally observed reduction of jet yields in ultrarelativistic heavy ion (AA) collisions relative to proton-proton (pp) collisions is widely interpreted in terms of energy loss of a hard scattered parton traversing a quark-gluon plasma (QGP) before fragmenting into a jet of hadrons. In order to constrain proposed mechanisms of energy loss, a variety of measurements are needed that quantify both how the jet yields and jet structure are modified in the medium. However, jets may also be modified by differences in the initial state of the nucleus relative to that of the proton. The precise determination of the QGP properties relies on disentangling these additional modifications, collectively termed ``cold nuclear matter'' effects, from energy loss in the QGP. Collisions between heavy ions and protons (pA) provide a potential control environment where cold nuclear matter effects should be present, but QGP formation is generally not expected to occur. In this talk, an overview of recent jet results from proton-lead collisions produced at the LHC will be given. The yield of inclusive jets and distributions of dijet pairs are shown to be compatible with generally accepted theoretical expectations, although significant modification is observed when yields are measured from specific centrality classes of pA collision events. Some measurements of high-pT charged hadron yields suggest a larger modification in pA collisions relative to pp collisions than for inclusive jet yields. The potential implications of this difference along with other measurements relating to jet structure will be discussed.

  18. Experimental studies in explicitly paradoxical interventions: results and implications.

    PubMed

    Strong, S R

    1984-09-01

    A dozen experimental studies have assessed the effectiveness of paradoxical interventions with agoraphobia, depression, insomnia and procrastination. The studies suggest that paradoxical interventions are more effective than no treatment and placebo treatment and are as effective and, in some instances, more effective than other behavioral interventions. Several studies show that the wording of paradoxical interventions affects their impact.

  19. Alkali Metal Backup Cooling for Stirling Systems - Experimental Results

    NASA Technical Reports Server (NTRS)

    Schwendeman, Carl; Tarau, Calin; Anderson, William G.; Cornell, Peggy A.

    2013-01-01

    In a Stirling Radioisotope Power System (RPS), heat must be continuously removed from the General Purpose Heat Source (GPHS) modules to maintain the modules and surrounding insulation at acceptable temperatures. The Stirling convertor normally provides this cooling. If the Stirling convertor stops in the current system, the insulation is designed to spoil, preventing damage to the GPHS at the cost of an early termination of the mission. An alkali-metal Variable Conductance Heat Pipe (VCHP) can be used to passively allow multiple stops and restarts of the Stirling convertor. In a previous NASA SBIR Program, Advanced Cooling Technologies, Inc. (ACT) developed a series of sodium VCHPs as backup cooling systems for Stirling RPS. The operation of these VCHPs was demonstrated using Stirling heater head simulators and GPHS simulators. In the most recent effort, a sodium VCHP with a stainless steel envelope was designed, fabricated and tested at NASA Glenn Research Center (GRC) with a Stirling convertor for two concepts; one for the Advanced Stirling Radioisotope Generator (ASRG) back up cooling system and one for the Long-lived Venus Lander thermal management system. The VCHP is designed to activate and remove heat from the stopped convertor at a 19 C temperature increase from the nominal vapor temperature. The 19 C temperature increase from nominal is low enough to avoid risking standard ASRG operation and spoiling of the Multi-Layer Insulation (MLI). In addition, the same backup cooling system can be applied to the Stirling convertor used for the refrigeration system of the Long-lived Venus Lander. The VCHP will allow the refrigeration system to: 1) rest during transit at a lower temperature than nominal; 2) pre-cool the modules to an even lower temperature before the entry in Venus atmosphere; 3) work at nominal temperature on Venus surface; 4) briefly stop multiple times on the Venus surface to allow scientific measurements. This paper presents the experimental

  20. Alkali Metal Backup Cooling for Stirling Systems - Experimental Results

    NASA Technical Reports Server (NTRS)

    Schwendeman, Carl; Tarau, Calin; Anderson, William G.; Cornell, Peggy A.

    2013-01-01

    In a Stirling Radioisotope Power System (RPS), heat must be continuously removed from the General Purpose Heat Source (GPHS) modules to maintain the modules and surrounding insulation at acceptable temperatures. The Stirling convertor normally provides this cooling. If the Stirling convertor stops in the current system, the insulation is designed to spoil, preventing damage to the GPHS at the cost of an early termination of the mission. An alkali-metal Variable Conductance Heat Pipe (VCHP) can be used to passively allow multiple stops and restarts of the Stirling convertor. In a previous NASA SBIR Program, Advanced Cooling Technologies, Inc. (ACT) developed a series of sodium VCHPs as backup cooling systems for Stirling RPS. The operation of these VCHPs was demonstrated using Stirling heater head simulators and GPHS simulators. In the most recent effort, a sodium VCHP with a stainless steel envelope was designed, fabricated and tested at NASA Glenn Research Center (GRC) with a Stirling convertor for two concepts; one for the Advanced Stirling Radioisotope Generator (ASRG) back up cooling system and one for the Long-lived Venus Lander thermal management system. The VCHP is designed to activate and remove heat from the stopped convertor at a 19 degC temperature increase from the nominal vapor temperature. The 19 degC temperature increase from nominal is low enough to avoid risking standard ASRG operation and spoiling of the Multi-Layer Insulation (MLI). In addition, the same backup cooling system can be applied to the Stirling convertor used for the refrigeration system of the Long-lived Venus Lander. The VCHP will allow the refrigeration system to: 1) rest during transit at a lower temperature than nominal; 2) pre-cool the modules to an even lower temperature before the entry in Venus atmosphere; 3) work at nominal temperature on Venus surface; 4) briefly stop multiple times on the Venus surface to allow scientific measurements. This paper presents the experimental

  1. Experimental Results for an Annular Aerospike with Differential Throttling

    NASA Technical Reports Server (NTRS)

    Ruf, Joseph H.; McDaniels, David M.

    2005-01-01

    A) MSFC funded an internal study on Altitude Compensating Nozzles: 1) Develop an ACN design and performance prediction tool. 2) Design, build and test cold flow ACN nozzles. 3) An annular aerospike nozzle was designed and tested. 4) Incorporated differential throttling to assess Thrust Vector Control. B) Objective of the test hardware: 1) Provide design tool verification. 2) Provide benchmark data for CFD calculations. 3) Experimentally measure side force, or TVC, for a differentially throttled annular aerospike.

  2. CP Violation in B Meson Decays: Experimental Results

    SciTech Connect

    Lanceri, Livio; /Trieste U. /INFN, Trieste

    2005-08-30

    CP violation is intimately connected with the puzzle of matter-antimatter asymmetry and baryogenesis. In the Standard Model of particle physics, the observed CP violation phenomena are accounted for by the Cabibbo-Kobayashi-Maskawa mechanism involving a phase in the quark mixing matrix. This paper is devoted to a review of the experimental status of CP violation in the decays of B mesons.

  3. Optimal active vibration absorber: Design and experimental results

    NASA Technical Reports Server (NTRS)

    Lee-Glauser, Gina; Juang, Jer-Nan; Sulla, Jeffrey L.

    1992-01-01

    An optimal active vibration absorber can provide guaranteed closed-loop stability and control for large flexible space structures with collocated sensors/actuators. The active vibration absorber is a second-order dynamic system which is designed to suppress any unwanted structural vibration. This can be designed with minimum knowledge of the controlled system. Two methods for optimizing the active vibration absorber parameters are illustrated: minimum resonant amplitude and frequency matched active controllers. The Controls-Structures Interaction Phase-1 Evolutionary Model at NASA LaRC is used to demonstrate the effectiveness of the active vibration absorber for vibration suppression. Performance is compared numerically and experimentally using acceleration feedback.

  4. Experimental overview of Generalized Parton Distribution results from HERMES

    SciTech Connect

    Zihlmann, B.

    2009-08-04

    Over the course of more than a decade the HERMES experiment has accumulated a wealth of data with electron and positron beams on various gaseous targets from Hydrogen up to Xenon. In addition, the beams and targets can be polarized. This data set is viewed in the context of Generalized Parton Distributions, a theoretical formalism with an explicit three dimensional view of the structure of the nucleon. It provides a link between experimental observables and the total angular momentum of the quarks in the nucleon.

  5. Experimental Studies of Ion Beam Neutralization: Preliminary Results

    SciTech Connect

    Ding, N.; Polansky, J.; Downey, R.; Wang, J.

    2011-05-20

    A testing platform is designed to study ion beam neutralization in the mesothermal, collisionless region. In the experimental setup, argon neutrals were ionized in a microwave cavity and accelerated by a plasma lens system which was biased to 2500 V above the system ground. Electrons were boiled off from two hot tungsten filaments to neutralize the ion beam. The plasma is diagnosed using Langmuir probe and Faraday probe. A 3-D traversing system and a complete data acquisition loop were developed to efficiently measure 3-D beam profile. Preliminary measurements of beam profiles are presented for different operating conditions.

  6. A comparison of passive coherent beam combining architectures: experimental results

    NASA Astrophysics Data System (ADS)

    Wan, Chenhao; Tiffany, Bradley; Leger, James R.

    2012-02-01

    Modal properties of two architectures for coherent beam combining are theoretically analyzed and experimentally verified. The supermodes of a two-laser spatially filtered cavity exhibit two distinctly different types of behavior depending on the path length error. When the error is small, the two modes present different cavity loss values and can be differentiated by gain. However, cavities containing path length errors greater than a critical value produce modes with identical losses and different resonant frequencies. A diode-bar side-pumped plano-concave Nd:YAG laser cavity is built for experimental verification of the theory. Experiments have shown two distinct regions as predicted by theory. In the small path length error region, the cavity runs in one single mode; however, when the path length error goes beyond a critical value, the cavity lases in two modes simultaneously or alternates between two modal states. Detailed loss versus phase error curves are presented and compared to theory. The modal behavior in this spatial filtering architecture is quite different from that found in a superposition architecture for coherent beam combining where the fundamental mode always has smaller loss per round trip than the second mode. The modal curves for a superposition architecture are provided for comparison with those from spatial filtering.

  7. Experimental results for a microscale ethanol vapor jet ejector

    NASA Astrophysics Data System (ADS)

    Gardner, W. G.; Jaworski, J. W.; Camacho, A. P.; Protz, J. M.

    2010-04-01

    A microscale jet ejector driven by ethanol vapor is designed and tested to induce a suction draft using a supersonic converging-diverging micronozzle. A three-dimensional axisymmetric nozzle is fabricated using electro-discharge machining to produce a throat diameter of 187 µm with an expansion ratio of 3:1. The motive nozzle achieves a design mass flow efficiency of 93% compared to isentropic calculations. Two different ejector area ratios are compared using ethanol vapor and nitrogen gas separately to motivate and entrain ambient air. The experimental data indicate that the ejector can produce a sufficient suction draft to satisfy both microengine mass flow and power off-take requirements to enable its substitution for high-speed microscale pumping turbomachinery.

  8. Geoacoustic and source tracking using particle filtering: experimental results.

    PubMed

    Yardim, Caglar; Gerstoft, Peter; Hodgkiss, William S

    2010-07-01

    A particle filtering (PF) approach is presented for performing sequential geoacoustic inversion of a complex ocean acoustic environment using a moving acoustic source. This approach treats both the environmental parameters [e.g., water column sound speed profile (SSP), water depth, sediment and bottom parameters] at the source location and the source parameters (e.g., source depth, range and speed) as unknown random variables that evolve as the source moves. This allows real-time updating of the environment and accurate tracking of the moving source. As a sequential Monte Carlo technique that operates on nonlinear systems with non-Gaussian probability densities, the PF is an ideal algorithm to perform tracking of environmental and source parameters, and their uncertainties via the evolving posterior probability densities. The approach is demonstrated on both simulated data in a shallow water environment with a sloping bottom and experimental data collected during the SWellEx-96 experiment.

  9. CSI Flight Computer System and experimental test results

    NASA Technical Reports Server (NTRS)

    Sparks, Dean W., Jr.; Peri, F., Jr.; Schuler, P.

    1993-01-01

    This paper describes the CSI Computer System (CCS) and the experimental tests performed to validate its functionality. This system is comprised of two major components: the space flight qualified Excitation and Damping Subsystem (EDS) which performs controls calculations; and the Remote Interface Unit (RIU) which is used for data acquisition, transmission, and filtering. The flight-like RIU is the interface between the EDS and the sensors and actuators positioned on the particular structure under control. The EDS and RIU communicate over the MIL-STD-1553B, a space flight qualified bus. To test the CCS under realistic conditions, it was connected to the Phase-0 CSI Evolutionary Model (CEM) at NASA Langley Research Center. The following schematic shows how the CCS is connected to the CEM. Various tests were performed which validated the ability of the system to perform control/structures experiments.

  10. Ambipolar transition voltage spectroscopy: Analytical results and experimental agreement

    NASA Astrophysics Data System (ADS)

    Bâldea, Ioan

    2012-01-01

    This work emphasizes that the transition voltages Vt± for both bias polarities (V ≷ 0) should be used to properly determine the energy offset ɛ0 of the molecular orbital closest to electrodes’ Fermi level and the bias asymmetry γ in molecular junctions. Accurate analytical formulas are deduced to estimate ɛ0 and γ solely in terms of Vt±. These estimates are validated against experiments, by showing that full experimental I-V curves measured by Beebe [Phys. Rev. Lett.PRLTAO0031-900710.1103/PhysRevLett.97.026801 97, 026801 (2006)] and Tan [Appl. Phsy. Lett.APPLAB0003-695110.1063/1.3291521 96, 013110 (2010)] for both bias polarities can be excellently reproduced.

  11. EXPERIMENTAL RESULTS FROM A MICROWAVE CAVITY BEAM POSITION MONITOR.

    SciTech Connect

    BALAKIN,V.; BAZHAN,A.; LUNEV,P.; SOLYAK,N.; VOGEL,V.; ZHOGOLEV,P.; LISITSYN,A.; YAKIMENKO,V.

    1999-03-29

    Future Linear Colliders have hard requirements for the beam transverse position stability in the accelerator. A beam Position Monitor (BPM) with the resolution better than 0.1 micron in the single bunch regime is needed to control the stability of the beam position along the linac. Proposed BPM is based on the measurement of the asymmetrical mode excited by single bunch in the cavity. Four stages of signal processing (space-, time-, frequency- and phase-filtering providing the required signal-to-noise ratio) are used to obtain extremely high resolution. The measurement set-up was designed by BINP and installed at ATF/BNL to test experimentally this concept. The set-up includes three two-coordinates BPM's at the frequency of 13.566 GHz, and reference intensity/phase cavity. BPM's were mounted on support table. The two-coordinates movers allow to move and align BPM's along the straight line, using the signals from the beam. The position of each monitor is controlled by the sensors with the accuracy 0.03 micron. The information from three monitors allows to exclude angle and position jitter of the beam and measure BPM resolution. In the experiments the resolution of about 0.15 micron for 0.25 nC beam intensity was obtained, that is close to the value required.

  12. Construction of a WMR for trajectory tracking control: experimental results.

    PubMed

    Silva-Ortigoza, R; Márquez-Sánchez, C; Marcelino-Aranda, M; Marciano-Melchor, M; Silva-Ortigoza, G; Bautista-Quintero, R; Ramos-Silvestre, E R; Rivera-Díaz, J C; Muñoz-Carrillo, D

    2013-01-01

    This paper reports a solution for trajectory tracking control of a differential drive wheeled mobile robot (WMR) based on a hierarchical approach. The general design and construction of the WMR are described. The hierarchical controller proposed has two components: a high-level control and a low-level control. The high-level control law is based on an input-output linearization scheme for the robot kinematic model, which provides the desired angular velocity profiles that the WMR has to track in order to achieve the desired position (x∗, y∗) and orientation (φ∗). Then, a low-level control law, based on a proportional integral (PI) approach, is designed to control the velocity of the WMR wheels to ensure those tracking features. Regarding the trajectories, this paper provides the solution or the following cases: (1) time-varying parametric trajectories such as straight lines and parabolas and (2) smooth curves fitted by cubic splines which are generated by the desired data points {(x₁∗, y₁∗),..., (x(n)∗, y(n)∗)}. A straightforward algorithm is developed for constructing the cubic splines. Finally, this paper includes an experimental validation of the proposed technique by employing a DS1104 dSPACE electronic board along with MATLAB/Simulink software. PMID:23997679

  13. Vaporization inside a mini microfin tube: experimental results and modeling

    NASA Astrophysics Data System (ADS)

    Diani, A.; Rossetto, L.

    2015-11-01

    This paper proposes a comparison among the common R134a and the extremely low GWP refrigerant R1234yf during vaporization inside a mini microfin tube. This microfin tube has an internal diameter of 2.4 mm, it has 40 fins, with a fin height of 0.12 mm. Due to the high heat transfer coefficients shown by this tube, this technology can lead to a refrigerant charge reduction. Tests were run in the Heat Transfer in Micro Geometries Lab of the Dipartimento di Ingegneria Industriale of the Università di Padova. Mass velocities range between 375 and 940 kg m-2 s-1, heat fluxes from 10 to 50 kW m-2, vapour qualities from 0.10 to 0.99, at a saturation temperature of 30°C. The comparison among the two fluids is proposed at the same operating conditions, in order to highlight the heat transfer and pressure drop differences among the two refrigerants. In addition, two correlations are proposed to estimate the heat transfer coefficient and frictional pressure drop during refrigerant flow boiling inside mini microfin tubes. These correlations well predict the experimental values, and thus they can be used as a useful tool to design evaporators based on these mini microfin tubes.

  14. Experimental results with hydrogen fueled internal combustion engines

    NASA Technical Reports Server (NTRS)

    De Boer, P. C. T.; Mclean, W. J.; Homan, H. S.

    1975-01-01

    The paper focuses on the most important experimental findings for hydrogen-fueled internal combustion engines, with particular reference to the application of these findings to the assessment of the potential of hydrogen engines. Emphasis is on the various tradeoffs that can be made, such as between maximum efficiency, maximum power, and minimum NO emissions. The various possibilities for induction and ignition are described. Some projections are made about areas in which hydrogen engines may find their initial application and about optimum ways to design such engines. It is shown that hydrogen-fueled reciprocal internal combustion engines offer important advantages with respect to thermal efficiency and exhaust emissions. Problems arising from preignition can suitably be avoided by restricting the fuel-air equivalence ratio to values below about 0.5. The direct cylinder injection appears to be a very attractive way to operate the engine, because it combines a wide range of possible power outputs with a high thermal efficiency and very low NO emissions at part loads.

  15. Construction of a WMR for Trajectory Tracking Control: Experimental Results

    PubMed Central

    Silva-Ortigoza, R.; Márquez-Sánchez, C.; Marcelino-Aranda, M.; Marciano-Melchor, M.; Silva-Ortigoza, G.; Bautista-Quintero, R.; Ramos-Silvestre, E. R.; Rivera-Díaz, J. C.; Muñoz-Carrillo, D.

    2013-01-01

    This paper reports a solution for trajectory tracking control of a differential drive wheeled mobile robot (WMR) based on a hierarchical approach. The general design and construction of the WMR are described. The hierarchical controller proposed has two components: a high-level control and a low-level control. The high-level control law is based on an input-output linearization scheme for the robot kinematic model, which provides the desired angular velocity profiles that the WMR has to track in order to achieve the desired position (x∗, y∗) and orientation (φ∗). Then, a low-level control law, based on a proportional integral (PI) approach, is designed to control the velocity of the WMR wheels to ensure those tracking features. Regarding the trajectories, this paper provides the solution or the following cases: (1) time-varying parametric trajectories such as straight lines and parabolas and (2) smooth curves fitted by cubic splines which are generated by the desired data points {(x1∗, y1∗),..., (xn∗, yn∗)}. A straightforward algorithm is developed for constructing the cubic splines. Finally, this paper includes an experimental validation of the proposed technique by employing a DS1104 dSPACE electronic board along with MATLAB/Simulink software. PMID:23997679

  16. Waste glass corrosion modeling: Comparison with experimental results

    SciTech Connect

    Bourcier, W.L.

    1993-11-01

    A chemical model of glass corrosion will be used to predict the rates of release of radionuclides from borosilicate glass waste forms in high-level waste repositories. The model will be used both to calculate the rate of degradation of the glass, and also to predict the effects of chemical interactions between the glass and repository materials such as spent fuel, canister and container materials, backfill, cements, grouts, and others. Coupling between the degradation processes affecting all these materials is expected. Models for borosilicate glass dissolution must account for the processes of (1) kinetically-controlled network dissolution, (2) precipitation of secondary phases, (3) ion exchange, (4) rate-limiting diffusive transport of silica through a hydrous surface reaction layer, and (5) specific glass surface interactions with dissolved cations and anions. Current long-term corrosion models for borosilicate glass employ a rate equation consistent with transition state theory embodied in a geochemical reaction-path modeling program that calculates aqueous phase speciation and mineral precipitation/dissolution. These models are currently under development. Future experimental and modeling work to better quantify the rate-controlling processes and validate these models are necessary before the models can be used in repository performance assessment calculations.

  17. An experimental investigation of multi-element airfoil ice accretion and resulting performance degradation

    NASA Technical Reports Server (NTRS)

    Potapczuk, Mark G.; Berkowitz, Brian M.

    1989-01-01

    An investigation of the ice accretion pattern and performance characteristics of a multi-element airfoil was undertaken in the NASA Lewis 6- by 9-Foot Icing Research Tunnel. Several configurations of main airfoil, slat, and flaps were employed to examine the effects of ice accretion and provide further experimental information for code validation purposes. The text matrix consisted of glaze, rime, and mixed icing conditions. Airflow and icing cloud conditions were set to correspond to those typical of the operating environment anticipated tor a commercial transport vehicle. Results obtained included ice profile tracings, photographs of the ice accretions, and force balance measurements obtained both during the accretion process and in a post-accretion evaluation over a range of angles of attack. The tracings and photographs indicated significant accretions on the slat leading edge, in gaps between slat or flaps and the main wing, on the flap leading-edge surfaces, and on flap lower surfaces. Force measurments indicate the possibility of severe performance degradation, especially near C sub Lmax, for both light and heavy ice accretion and performance analysis codes presently in use. The LEWICE code was used to evaluate the ice accretion shape developed during one of the rime ice tests. The actual ice shape was then evaluated, using a Navier-Strokes code, for changes in performance characteristics. These predicted results were compared to the measured results and indicate very good agreement.

  18. Dynamic modeling and experimental results for a head tilt response.

    PubMed

    Geisinger, Dario; Ferreira, Enrique; Suarez, Alejo; Suarez, Hamlet

    2010-01-01

    The estimation of the vertical in humans is important in everyday life although the mechanisms involved are not completely understood yet. This paper presents two sets of experiments with normal subjects, using the same virtual reality setup, aiming to help in this understanding. First, a steady state experiment is presented, which is used to determine the gravitational vertical precision while the second, a dynamical transient response experiment, is used to find dynamic models of each subject response. Results show that the dynamic models are able to reproduce the results of the steady state experiment while having the benefits that a dynamic model brings to evaluate subjects performance.

  19. Joint Soviet-American experiment on hypokinesia: Experimental results

    NASA Technical Reports Server (NTRS)

    Burovskiy, N. N.

    1979-01-01

    Comprehensive results are reported from the Soviet portion of a joint Soviet-American experiment involving hypokinesia. The main emphases are on chemical analyses of blood and urine, functional tests, and examination of the cardiovascular system by electrocardiography, echocardiography, and plethysmography.

  20. The behavior of delaminations in composite materials - experimental results

    NASA Astrophysics Data System (ADS)

    Chermoshentseva, A. S.; Pokrovskiy, A. M.; Bokhoeva, L. A.

    2016-02-01

    Delamination is one of the most common failure modes of composite materials. It may occur as a consequence of imperfections in the production process or the effects of external factors during the operational life of the composite laminates, such as the impact by foreign objects. This paper presents the results of mechanical tests and the optimum degrees of filling the composite materials (CM) with hydrophobic powder (Tarkosil T-20) depending on the latter mass concentration. The results present test samples of the CM with the underlying interlayer defects. The samples were fabricated of twenty-ply pre-preg (fiberglass or carbon fiber). The industrial grade glass is T-25 (VM) specification 6-11-380-76. The composite materials have nanosized additives in structure. The volume concentration of nanopowders is varying from 0.1% to 0.5%. This kind of research has been done for the first time.

  1. Delaminations in composite plates under transverse static loads - Experimental results

    NASA Technical Reports Server (NTRS)

    Finn, Scott R.; He, Yi-Fei; Springer, George S.

    1992-01-01

    Tests were performed measuring the damage initiation loads and the locations, shapes, and sizes of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite-PEEK plates subjected to transverse static loads. The data were compared to the results of the Finn-Springer model, and good agreements were found between the measured and calculated delamination lengths and widths.

  2. Delaminations in composite plates under transverse static loads - Experimental results

    NASA Astrophysics Data System (ADS)

    Finn, Scott R.; He, Yi-Fei; Springer, George S.

    1992-11-01

    Tests were performed measuring the damage initiation loads and the locations, shapes, and sizes of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite-PEEK plates subjected to transverse static loads. The data were compared to the results of the Finn-Springer model, and good agreements were found between the measured and calculated delamination lengths and widths.

  3. Experimental test accelerator: description and results of initial experiments

    SciTech Connect

    Fessenden, T.; Birx, D.; Briggs, R.

    1980-06-02

    The ETA is a high current (10,000 Amp) linear induction accelerator that produces short (30 ns) pulses of electrons at 5 MeV twice per second or in bursts of 5 pulses separated by as little as one millisecond. At this time the machine has operated at 65% of its design current and 90% of the design voltage. This report contains a description of the accelerator and its diagnostics; the results of the initial year of operation; a comparison of design codes with experiments on beam transport; and a discussion of some of the special problems and their status.

  4. Delaminations in composite plates under transverse impact loads - Experimental results

    NASA Technical Reports Server (NTRS)

    Finn, Scott R.; He, Ye-Fei; Springer, George S.

    1993-01-01

    Tests were performed measuring the locations and geometries of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite/PEEK plates subjected to transverse impact loads. The data provide specific information on the effects of impactor velocity, impactor mass, material, thickness of back ply group, difference in fiber orientation between adjacent ply groups, plate thickness, and impactor nose radius. The data were compared to the results of the Finn-Springer model. The model was found to describe the data with reasonable accuracy.

  5. Experimental results of a propeller/wing interaction study

    NASA Technical Reports Server (NTRS)

    Johnson, Robert T.; Sullivan, John P.; Witkowski, David P.

    1991-01-01

    Steady state measurements have been performed on a propellar and a wing in a tractor configuration, to investigate the consequences of mutual interference on overall performance. For certain geometries wing lift is found to be enhanced, and wing drag to be decreased. The unsteady nature of the propeller-wing aerodynamic interaction has been studied using flow visualization. Results obtained indicate that the tip vortex is severed at the wing leading edge, the severed tip vortex filaments shear in a spanwise direction relative to one another, and these displaced filaments deform to reconnect at the trailing edge.

  6. Delaminations in composite plates under transverse impact loads - Experimental results

    NASA Astrophysics Data System (ADS)

    Finn, Scott R.; He, Ye-Fei; Springer, George S.

    Tests were performed measuring the locations and geometries of delaminations in Fiberite T300/976 graphite/epoxy, Fiberite IM7/977-2 graphite-toughened epoxy, and ICI APC-2 graphite/PEEK plates subjected to transverse impact loads. The data provide specific information on the effects of impactor velocity, impactor mass, material, thickness of back ply group, difference in fiber orientation between adjacent ply groups, plate thickness, and impactor nose radius. The data were compared to the results of the Finn-Springer model. The model was found to describe the data with reasonable accuracy.

  7. Parallel and Distributed Computational Fluid Dynamics: Experimental Results and Challenges

    NASA Technical Reports Server (NTRS)

    Djomehri, Mohammad Jahed; Biswas, R.; VanderWijngaart, R.; Yarrow, M.

    2000-01-01

    This paper describes several results of parallel and distributed computing using a large scale production flow solver program. A coarse grained parallelization based on clustering of discretization grids combined with partitioning of large grids for load balancing is presented. An assessment is given of its performance on distributed and distributed-shared memory platforms using large scale scientific problems. An experiment with this solver, adapted to a Wide Area Network execution environment is presented. We also give a comparative performance assessment of computation and communication times on both the tightly and loosely-coupled machines.

  8. Acceleration and torque feedback for robotic control - Experimental results

    NASA Technical Reports Server (NTRS)

    Mclnroy, John E.; Saridis, George N.

    1990-01-01

    Gross motion control of robotic manipulators typically requires significant on-line computations to compensate for nonlinear dynamics due to gravity, Coriolis, centripetal, and friction nonlinearities. One controller proposed by Luo and Saridis avoids these computations by feeding back joint acceleration and torque. This study implements the controller on a Puma 600 robotic manipulator. Joint acceleration measurement is obtained by measuring linear accelerations of each joint, and deriving a computationally efficient transformation from the linear measurements to the angular accelerations. Torque feedback is obtained by using the previous torque sent to the joints. The implementation has stability problems on the Puma 600 due to the extremely high gains inherent in the feedback structure. Since these high gains excite frequency modes in the Puma 600, the algorithm is modified to decrease the gain inherent in the feedback structure. The resulting compensator is stable and insensitive to high frequency unmodeled dynamics. Moreover, a second compensator is proposed which uses acceleration and torque feedback, but still allows nonlinear terms to be fed forward. Thus, by feeding the increment in the easily calculated gravity terms forward, improved responses are obtained. Both proposed compensators are implemented, and the real time results are compared to those obtained with the computed torque algorithm.

  9. Space Launch System Base Heating Test: Experimental Operations & Results

    NASA Technical Reports Server (NTRS)

    Dufrene, Aaron; Mehta, Manish; MacLean, Matthew; Seaford, Mark; Holden, Michael

    2016-01-01

    NASA's Space Launch System (SLS) uses four clustered liquid rocket engines along with two solid rocket boosters. The interaction between all six rocket exhaust plumes will produce a complex and severe thermal environment in the base of the vehicle. This work focuses on a recent 2% scale, hot-fire SLS base heating test. These base heating tests are short-duration tests executed with chamber pressures near the full-scale values with gaseous hydrogen/oxygen engines and RSRMV analogous solid propellant motors. The LENS II shock tunnel/Ludwieg tube tunnel was used at or near flight duplicated conditions up to Mach 5. Model development was based on the Space Shuttle base heating tests with several improvements including doubling of the maximum chamber pressures and duplication of freestream conditions. Test methodology and conditions are presented, and base heating results from 76 runs are reported in non-dimensional form. Regions of high heating are identified and comparisons of various configuration and conditions are highlighted. Base pressure and radiometer results are also reported.

  10. Experimental Results of Guided Wave Travel Time Tomography

    NASA Astrophysics Data System (ADS)

    Volker, Arno; Bloom, Joost

    2011-06-01

    Corrosion is one of the industries major issues regarding the integrity of assets. Currently inspections are conducted at regular intervals to ensure a sufficient integrity level of these assets. Cost reduction while maintaining a high level of reliability and safety of installations is a major challenge. The concept of predictive maintenance using permanent sensors that monitor the integrity of an installation matches very well with the objective to reduce cost while maintaining a high safety level. Guided waves are very attractive for permanent monitoring systems because they can travel over large distances and therefore provide the essential large area coverage. Making use of the dispersive behavior of the guided waves, a wall thickness map over a distance of several meters can be made using only two rings of guided wave transducers. Travel time tomography is used to translate transmission travel times into a wall thickness map. This method has been applied in the field for the first time to map the wall thickness under two clearly corroded pipe supports of a 8″ and 10″ gas pipe line. The tomographic inversion results clearly maps the corrosion under the supports. Independent reference measurements confirm the tomographic inversion results.

  11. M-I-S solar cell - Theory and experimental results

    NASA Technical Reports Server (NTRS)

    Childs, R.; Fortuna, J.; Geneczko, J.; Fonash, S. J.

    1976-01-01

    The paper presents an operating-mode analysis of an MIS solar cell and discusses the advantages which can arise as a result of the use of transport control, field shaping (increased n factor), and zero bias barrier height modification. It is noted that for an n-type semiconductor, it is relatively easy to obtain an enhanced n factor using acceptor-like states without an increase in diode saturation current, the converse being true for p-type semiconductors. Several MIS configurations are examined: an acceptor-like, localized state configuration producing field shaping and no change in diode saturation current, and acceptor-like localized configurations producing field shaping, with a decrease of diode saturation current, in one case, and an increase in the other.

  12. Experimental Results on Statistical Approaches to Page Replacement Policies

    SciTech Connect

    LEUNG,VITUS J.; IRANI,SANDY

    2000-12-08

    This paper investigates the questions of what statistical information about a memory request sequence is useful to have in making page replacement decisions: Our starting point is the Markov Request Model for page request sequences. Although the utility of modeling page request sequences by the Markov model has been recently put into doubt, we find that two previously suggested algorithms (Maximum Hitting Time and Dominating Distribution) which are based on the Markov model work well on the trace data used in this study. Interestingly, both of these algorithms perform equally well despite the fact that the theoretical results for these two algorithms differ dramatically. We then develop succinct characteristics of memory access patterns in an attempt to approximate the simpler of the two algorithms. Finally, we investigate how to collect these characteristics in an online manner in order to have a purely online algorithm.

  13. Microgravity Fluid Separation Physics: Experimental and Analytical Results

    NASA Technical Reports Server (NTRS)

    Shoemaker, J. Michael; Schrage, Dean S.

    1997-01-01

    Effective, low power, two-phase separation systems are vital for the cost-effective study and utilization of two-phase flow systems and flow physics of two-phase flows. The study of microgravity flows have the potential to reveal significant insight into the controlling mechanisms for the behavior of flows in both normal and reduced gravity environments. The microgravity environment results in a reduction in gravity induced buoyancy forces acting on the discrete phases. Thus, surface tension, viscous, and inertial forces exert an increased influence on the behavior of the flow as demonstrated by the axisymmetric flow patterns. Several space technology and operations groups have studied the flow behavior in reduced gravity since gas-liquid flows are encountered in several systems such as cabin humidity control, wastewater treatment, thermal management, and Rankine power systems.

  14. New experimental results in atlas-based brain morphometry

    NASA Astrophysics Data System (ADS)

    Gee, James C.; Fabella, Brian A.; Fernandes, Siddharth E.; Turetsky, Bruce I.; Gur, Ruben C.; Gur, Raquel E.

    1999-05-01

    In a previous meeting, we described a computational approach to MRI morphometry, in which a spatial warp mapping a reference or atlas image into anatomic alignment with the subject is first inferred. Shape differences with respect to the atlas are then studied by calculating the pointwise Jacobian determinant for the warp, which provides a measure of the change in differential volume about a point in the reference as it transforms to its corresponding position in the subject. In this paper, the method is used to analyze sex differences in the shape and size of the corpus callosum in an ongoing study of a large population of normal controls. The preliminary results of the current analysis support findings in the literature that have observed the splenium to be larger in females than in males.

  15. Experimental results on low alpha electron-storage rings

    SciTech Connect

    Robin, D.; Hama, H.; Nadji, A.

    1995-09-01

    The authors report on experiments performed in two synchrotron light sources, UVSOR and Super-ACO, where the momentum compaction factor is reduced in order to reduce the bunch length. By controlling the second-order momentum compaction factor, UVSOR and Super-ACO have managed to reduce the first-order momentum compaction factor by 100. At low current the resulting bunch lengths are less than 10 ps, a factor of 10 smaller than normal. Measurements of current dependent bunch lengthening in UVSOR are presented and the cause of the bunch lengthening is determined to be potential-well distortion. The authors also show that by operating with a negative momentum compaction factor, SuperACO has achieved shorter bunch lengthening and higher peak currents than at positive momentum compaction.

  16. Longitudinal variation of the equatorial ionosphere: Modeling and experimental results

    NASA Astrophysics Data System (ADS)

    Souza, J. R.; Asevedo, W. D.; dos Santos, P. C. P.; Petry, A.; Bailey, G. J.; Batista, I. S.; Abdu, M. A.

    2013-02-01

    We describe a new version of the Parameterized Regional Ionospheric Model (PARIM) which has been modified to include the longitudinal dependences. This model has been reconstructed using multidimensional Fourier series. To validate PARIM results, the South America maps of critical frequencies for the E (foE) and F (foF2) regions were compared with the values calculated by Sheffield Plasmasphere-Ionosphere Model (SUPIM) and IRI representations. PARIM presents very good results, the general characteristics of both regions, mainly the presence of the equatorial ionization anomaly, were well reproduced for equinoctial conditions of solar minimum and maximum. The values of foF2 and hmF2 recorded over Jicamarca (12°S; 77°W; dip lat. 1°N; mag. declination 0.3°) and sites of the conjugate point equatorial experiment (COPEX) campaign Boa Vista (2.8°N; 60.7°W; dip lat. 11.4°; mag. declination -13.1°), Cachimbo (9.5°S; 54.8°W; dip lat. -1.8°; mag. declination -15.5°), and Campo Grande (20.4°S; 54.6°W; dip lat. -11.1°; mag. declination -14.0°) have been used in this work. foF2 calculated by PARIM show good agreement with the observations, except during morning over Boa Vista and midnight-morning over Campo Grande. Some discrepancies were also found for the F-region peak height (hmF2) near the geomagnetic equator during times of F3 layer occurrences. IRI has underestimated both foF2 and hmF2 over equatorial and low latitude sectors during evening-nighttimes, except for Jicamarca where foF2 values were overestimated.

  17. The experimental results and analysis of a borehole radar prototype

    NASA Astrophysics Data System (ADS)

    Liu, Sixin; Wu, Junjun; Dong, Hang; Fu, Lei; Wang, Fei

    2012-04-01

    A prototype of borehole radar has been successfully tested in three sites for different purposes under a field condition. The objective of the prototype is providing an effective down-hole tool for detecting targets in deep boreholes situated in a relatively high conductivity area such as the metal ores. The first testing site is at a geothermal field. The fractures extending more than 20 m from the borehole are delineated by the borehole radar in the single-hole reflection mode. The second testing site is located in a jade mine for basement evaluation. The cross-hole measurement mode was used to detect the cavities made by previous unorganized mining activities. Several high-velocity anomalies were found in the velocity profile and presumably the targets of the mine shafts and tunnels. The third test site is located in a mineralized belt characterized by low resistivity less than 1000 Ohm m, the surface-borehole measurement was carried out and the data were processed with velocity tomography. The low-velocity zone corresponds to a mineralized zone from geological records. The three testing results proved the readiness of this borehole radar prototype for further deployment in more complicated and realistic field situations.

  18. Infrared thermography for CFRP inspection: computational model and experimental results

    NASA Astrophysics Data System (ADS)

    Fernandes, Henrique C.; Zhang, Hai; Morioka, Karen; Ibarra-Castanedo, Clemente; López, Fernando; Maldague, Xavier P. V.; Tarpani, José R.

    2016-05-01

    Infrared Thermography (IRT) is a well-known Non-destructive Testing (NDT) technique. In the last decades, it has been widely applied in several fields including inspection of composite materials (CM), specially the fiber-reinforced polymer matrix ones. Consequently, it is important to develop and improve efficient NDT techniques to inspect and assess the quality of CM parts in order to warranty airworthiness and, at the same time, reduce costs of airline companies. In this paper, active IRT is used to inspect carbon fiber-reinforced polymer (CFRP) at laminate with artificial inserts (built-in sample) placed on different layers prior to the manufacture. Two optical active IRT are used. The first is pulsed thermography (PT) which is the most widely utilized IRT technique. The second is a line-scan thermography (LST) technique: a dynamic technique, which can be employed for the inspection of materials by heating a component, line-by-line, while acquiring a series of thermograms with an infrared camera. It is especially suitable for inspection of large parts as well as complex shaped parts. A computational model developed using COMSOL Multiphysics® was used in order to simulate the inspections. Sequences obtained from PT and LST were processed using principal component thermography (PCT) for comparison. Results showed that it is possible to detect insertions of different sizes at different depths using both PT and LST IRT techniques.

  19. First experimental results on the IShTAR testbed

    SciTech Connect

    D’Inca, R.; Jacquot, J.; Ochoukov, R.; Morgal, I.; Fünfgelder, H.; Faugel, H.; Crombe, K.; Louche, F.; Van Eester, D.; Heuraux, S.; Devaux, S.; Moritz, J.; Faudot, E.; Noterdaeme, J.-M.

    2015-12-10

    IShTAR (Ion cyclotron Sheath Test ARrangement) is a linear magnetized plasma test facility dedicated to the investigation of RF wave/plasma interaction [1] in the Ion Cyclotron Range of Frequencies (ICRF). It provides a better accessibility for the instrumentation than tokamaks while being representative of the neighboring region of the wave emitter. It is equipped with a magnetized plasma source (1 m long, 0.4 m diameter) powered by a helical antenna up to 3 kW at 11 MHz. We present the results of the first analysis of the plasma characteristics (plasma density, electron temperature) in function of the operating parameters (injected power, neutral pressure and magnetic field) as measured with fixed and movable Langmuir probes, spectrometer and cameras. The plasma is presently produced only by the helical antenna (no ICRF). We show that the plasma exists in three regime depending on the power level: the first two ones are stable and separated by a jump in density; a first spatial profile of the plasma density has been established for these modes; The third mode is unstable, characterized by strong oscillations of the plasma tube position.

  20. Preliminary experimental results for a cryogenic brush seal configuration

    NASA Astrophysics Data System (ADS)

    Carlile, J. A.; Hendricks, R. C.; Hibbs, R. I.; McVey, S. E.; Scharrer, J. K.

    1993-06-01

    Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun porous flow equation was applied to the brush seal data. The Ergun relation, which required heuristic information to characterize the coefficients, fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the (C(sub f)A x Constant) flow and area coefficients. Reasonable agreement between prediction and data was found, as expected, but such methods are not to be construed as two-phase-flow brush seal analyses.

  1. Preliminary experimental results for a cryogenic brush seal configuration

    NASA Astrophysics Data System (ADS)

    Carlile, J. A.; Hendricks, R. C.; Hibbs, R. I.; McVey, S. E.; Scharrer, J. K.

    1993-06-01

    Preliminary fluid nitrogen flow data are reported for a five-brush, ceramic-coated-rub-runner brush seal system, where the brushes and the rub runner were placed at each end of a centrally pressurized multifunction tester ('back-to-back' set of brushes) and tested at rotor speeds of 0, 10, 18, and 22.5 krpm. After testing, both the brushes and the ceramic-coated rub runner appeared pristine. The coating withstood both the thermomechanical and dynamic loadings with minor wear track scarring. The bristle tips showed some indication of material shearing (smearing) wear. The Ergun (1952) porous flow equation was applied to the brush seal data. The Ergun relation fit the gaseous data but was in poor agreement with the fluid results. The brush seal exit conditions were two phase. Two-phase, choked-flow design charts were applied but required one data point at each rotor speed to define the flow and area coefficients. Reasonable agreement between prediction and data was found, but such methods are not to be construed as two-phase-flow brush seal analyses.

  2. Impact ejecta dynamics in an atmosphere - Experimental results and extrapolations

    NASA Technical Reports Server (NTRS)

    Schultz, P. H.; Gault, D. E.

    1982-01-01

    It is noted that the impacts of 0.635-cm aluminum projectiles at 6 km/sec into fine pumice dust, at 1 atm, generate a ball of ionized gas behind an expanding curtain of upward moving ejecta. The gas ball forms a toroid which dissolves as it is driven along the interior of the ejecta curtain, by contrast to near-surface explosions in which a fireball envelops early-time crater growth. High frame rate Schlieren photographs show that the atmosphere at the base of the ejecta curtain is initially turbulent, but later forms a vortex. These experiments suggest that although small size ejecta may be decelerated by air drag, they are not simply lofted and suspended but become incorporated in an ejecta cloud that is controlled by air flow which is produced by the response of the atmosphere to the impact. The extrapolation of these results to large body impacts on the earth suggests such contrasts with laboratory experiments as a large quantity of impact-generated vapor, the supersonic advance of the ejecta curtain, the lessened effect of air drag due to the tenuous upper atmosphere, and the role of secondary cratering.

  3. Experimental aflatoxicosis in swine: morphological and clinical pathological results.

    PubMed Central

    Miller, D M; Stuart, B P; Crowell, W A

    1981-01-01

    The morphological changes in livers of 30 feeder pigs fed diets containing corn contaminated by aflatoxins (0.0 microgram aflatoxins/g feed, 0.4 microgram aflatoxin/g feed, and 0.8 microgram aflatoxin/g feed) were compared with changes in hematology, liver specific serum enzymes, serum proteins, and lymphocyte stimulation indices. Histologically, the livers were classified into five groups. Pigs fed the 0.8 microgram/g diets had the most severe histological lesions of karyomegaly, bile ductule proliferation and hepatocellular degeneration plus elevated gamma-glutamyl transpeptidase, aspartate aminotransferase, and alkaline phosphatase. This group also had significantly lower total protein and albumin values compared to the control pigs. Variation in the severity of the histological lesions was seen in pigs fed 0.4 microgram/g diets as well as variation in lymphocyte indices, liver specific serum enzymes, and electrophoretic results in the affected pigs in that group. Images Fig. 1. Fig. 2. Fig. 3. Fig. 4. Fig. 5. PMID:7337866

  4. Experimental Results of Integrated Refrigeration and Storage System Testing

    NASA Technical Reports Server (NTRS)

    Notardonato, W. U.; Johnson, W. L.; Jumper, K.

    2009-01-01

    Launch operations engineers at the Kennedy Space Center have identified an Integrated Refrigeration and Storage system as a promising technology to reduce launch costs and enable advanced cryogenic operations. This system uses a close cycle Brayton refrigerator to remove energy from the stored cryogenic propellant. This allows for the potential of a zero loss storage and transfer system, as well and control of the state of the propellant through densification or re-liquefaction. However, the behavior of the fluid in this type of system is different than typical cryogenic behavior, and there will be a learning curve associated with its use. A 400 liter research cryostat has been designed, fabricated and delivered to KSC to test the thermo fluid behavior of liquid oxygen as energy is removed from the cryogen by a simulated DC cycle cryocooler. Results of the initial testing phase focusing on heat exchanger characterization and zero loss storage operations using liquid oxygen are presented in this paper. Future plans for testing of oxygen densification tests and oxygen liquefaction tests will also be discussed. KEYWORDS: Liquid Oxygen, Refrigeration, Storage

  5. Bridge Testing With Ground-Based Interferometric Radar: Experimental Results

    SciTech Connect

    Chiara, P.; Morelli, A.

    2010-05-28

    The research of innovative non-contact techniques aimed at the vibration measurement of civil engineering structures (also for damage detection and structural health monitoring) is continuously directed to the optimization of measures and methods. Ground-Based Radar Interferometry (GBRI) represents the more recent technique available for static and dynamic control of structures and ground movements.Dynamic testing of bridges and buildings in operational conditions are currently performed: (a) to assess the conformity of the structure to the project design at the end of construction; (b) to identify the modal parameters (i.e. natural frequencies, mode shapes and damping ratios) and to check the variation of any modal parameters over the years; (c) to evaluate the amplitude of the structural response to special load conditions (i.e. strong winds, earthquakes, heavy railway or roadway loads). If such tests are carried out by using a non-contact technique (like GBRI), the classical issues of contact sensors (like accelerometers) are easily overtaken.This paper presents and discusses the results of various tests carried out on full-scale bridges by using a Stepped Frequency-Continuous Wave radar system.

  6. EXPERIMENTAL RESULTS OF THE NEPHELINE PHASE III STUDY

    SciTech Connect

    Fox, K.; Edwards, T.

    2009-11-09

    This study is the third phase in a series of experiments designed to reduce conservatism in the model that predicts the formation of nepheline, a crystalline phase that can reduce the durability of high level waste glass. A Phase I study developed a series of glass compositions that were very durable while their nepheline discriminator values were well below the current nepheline discriminator limit of 0.62, where nepheline is predicted to crystallize upon slow cooling. A Phase II study selected glass compositions to identify any linear effects of composition on nepheline crystallization and that were restricted to regions that fell within the validation ranges of the Defense Waste Processing Facility (DWPF) Product Composition Control System (PCCS) models. However, it was not possible to identify any linear effects of composition on chemical durability performance for this set of study glasses. The results of the Phase II study alone were not sufficient to recommend modification of the current nepheline discriminator. It was recommended that the next series of experiments continue to focus not only on compositional regions where the PCCS models are considered applicable (i.e., the model validation ranges), but also be restricted to compositional regions where the only constraint limiting processing is the current nepheline discriminator. Two methods were used in selecting glasses for this Phase III nepheline study. The first was based on the relationship of the current nepheline discriminator model to the other DWPF PCCS models, and the second was based on theory of crystallization in mineral and glass melts. A series of 29 test glass compositions was selected for this study using a combination of the two approaches. The glasses were fabricated and characterized in the laboratory. After reviewing the data, the study glasses generally met the target compositions with little issue. Product Consistency Test results correlated well with the crystallization analyses in

  7. Photoacoustic contrast enhancement using selective subband imaging: experimental results

    NASA Astrophysics Data System (ADS)

    Wei, Chen-Wei; Sheu, Yae-lin; Li, Pai-Chi

    2007-02-01

    In photoacoustic imaging, the difference of optical absorption determines the contrast between two media. In this study, a contrast enhancement method based on choosing various frequency subbands for photoacoustic imaging is proposed. Typically, a laser beam irradiates a medium of interest, and the optical energy decays with different rates as the optical absorption changes. The decay profiles result in acoustic pressure waveforms to propagate with various frequency components, which cause the acoustic frequency variation. The frequency band for a medium with high absorption is found significantly up-shifted from that for a medium with one order lower absorption. Accordingly, besides the amplitude difference due to the absorption, the contrast between two media with varied absorption can be further enhanced by choosing a high frequency band of the receiving signals for imaging. This method was demonstrated by simulations and experiments. The simulation, which is based on the Beer-Lambert law, verified the appearance of frequency variation due to the disparity of absorption coefficients. The experiments were performed by using agar phantom with various concentrations of graphite to create optical absorptions with more than tens times difference. For absorbers with absorption coefficients from 2.5 cm -1 to 100 cm -1, the peak frequencies and the -6 dB bandwidths of the PA signals increase from 1.17 to 3.83 MHz and from 2.17 to 7.58 MHz, respectively. The subband image at band 7-14 MHz shows 13-25 dB intensity difference between two agars with respective absorption of 41.75 cm -1 and 5.01 cm -1, while the difference is 9-15 dB at band 0-7 MHz, thus demonstrating that the contrast can be enhanced between two media using the selective subband imaging. The potential of improving the contrast between biological tissues and contrast agent with a significant higher absorption is revealed.

  8. Impact Flash Physics: Modeling and Comparisons With Experimental Results

    NASA Astrophysics Data System (ADS)

    Rainey, E.; Stickle, A. M.; Ernst, C. M.; Schultz, P. H.; Mehta, N. L.; Brown, R. C.; Swaminathan, P. K.; Michaelis, C. H.; Erlandson, R. E.

    2015-12-01

    horizontal. High-speed radiometer measurements were made of the time-dependent impact flash at wavelengths of 350-1100 nm. We will present comparisons between these measurements and the output of APL's model. The results of this validation allow us to determine basic relationships between observed optical signatures and impact conditions.

  9. Investigation of the Actual Causes of Hip Joint Implant Loosening Classified as Aseptic--Analysis of Microbiological Culture Results and Levels of Inflammatory Markers.

    PubMed

    Strzelec-Nowak, Dagmara; Kozioł-Montewka, Maria; Niedźwiadek, Justyna; Bogut, Agnieszka; Blacha, Jan; Mazurkiewicz, Tomasz

    2015-01-01

    Loosening of the hip joint prosthesis is considered as one of the most significant postoperative complications in recent years. The laboratory diagnostic procedure used to differentiate periprosthetic infection from aseptic loosening is very difficult because of the biofilm which microorganisms form on the implant surface. The purpose of this research was to evaluate the level of concordance between clinical classification of implant loosening among 50 patients subjected to reimplantation procedure and laboratory investigation of PJI including microbiological culture results and the levels of inflammatory markers assessed in the patients' synovial fluid samples, serum, and full blood. The synovial fluid was collected for leukocyte count, differential cell count, and culture on standard media. The levels of systemic inflammation markers such as the ESR and CRP concentration were determined in serum and full blood. Tissue samples were collected for microbiological studies. Components from endoprostheses were exposed to ultrasound in a process called sonication. Among the parameters measured in serum and full blood the levels of ESR and CRP were higher in the septic group of patients. Cytologic analysis of synovial fluid was in correlation with microbiologic identification. The most frequent isolated bacteria was Staphylococcus epidermidis. Culture results from materials such as synovial fluid, sonicate and tissues are crucial to establish the infectious aetiology of the loosening. Microscopic analysis of synovial fluid represents a simple, rapid and accurate method for differentiating PJI from aseptic failure. Sonication increases detection of the infectious process, and culture results are in correlation with the cytologic analysis of synovial fluid.

  10. Investigation of the Actual Causes of Hip Joint Implant Loosening Classified as Aseptic--Analysis of Microbiological Culture Results and Levels of Inflammatory Markers.

    PubMed

    Strzelec-Nowak, Dagmara; Kozioł-Montewka, Maria; Niedźwiadek, Justyna; Bogut, Agnieszka; Blacha, Jan; Mazurkiewicz, Tomasz

    2015-01-01

    Loosening of the hip joint prosthesis is considered as one of the most significant postoperative complications in recent years. The laboratory diagnostic procedure used to differentiate periprosthetic infection from aseptic loosening is very difficult because of the biofilm which microorganisms form on the implant surface. The purpose of this research was to evaluate the level of concordance between clinical classification of implant loosening among 50 patients subjected to reimplantation procedure and laboratory investigation of PJI including microbiological culture results and the levels of inflammatory markers assessed in the patients' synovial fluid samples, serum, and full blood. The synovial fluid was collected for leukocyte count, differential cell count, and culture on standard media. The levels of systemic inflammation markers such as the ESR and CRP concentration were determined in serum and full blood. Tissue samples were collected for microbiological studies. Components from endoprostheses were exposed to ultrasound in a process called sonication. Among the parameters measured in serum and full blood the levels of ESR and CRP were higher in the septic group of patients. Cytologic analysis of synovial fluid was in correlation with microbiologic identification. The most frequent isolated bacteria was Staphylococcus epidermidis. Culture results from materials such as synovial fluid, sonicate and tissues are crucial to establish the infectious aetiology of the loosening. Microscopic analysis of synovial fluid represents a simple, rapid and accurate method for differentiating PJI from aseptic failure. Sonication increases detection of the infectious process, and culture results are in correlation with the cytologic analysis of synovial fluid. PMID:26373172

  11. Electromagnetic (EM) earthquake precursor transmission and detection regarding experimental field and laboratory results.

    NASA Astrophysics Data System (ADS)

    Jones, Kenneth B., II; Saxton, Patrick

    2016-04-01

    increased, variable geometry. The blocks were all successfully fractured with expansionary cement netting consecutive and identical EM emission results very similar to the Timpson pre-earthquake results. Cored granite made up the largest amount of rock test types, due to the large volume occurring as basement rock. EM transmission in the ELF range ascending from depth was theorized to follow paths of least resistance via faults and other fracture spaces than actual penetration through solid rock, which may attenuate both signal strength and frequency response. Fault geometry, fracture orientation/termination, and subsurface reflection may make epicenter determinations problematic; however, EM emissions will continually occur and be detectable with further signal analyses in refining epicentral locations.

  12. Form and Actuality

    NASA Astrophysics Data System (ADS)

    Bitbol, Michel

    A basic choice underlies physics. It consists of banishing actual situations from theoretical descriptions, in order to reach a universal formal construct. Actualities are then thought of as mere local appearances of a transcendent reality supposedly described by the formal construct. Despite its impressive success, this method has left major loopholes in the foundations of science. In this paper, I document two of these loopholes. One is the problem of time asymmetry in statistical thermodynamics, and the other is the measurement problem of quantum mechanics. Then, adopting a broader philosophical standpoint, I try to turn the whole picture upside down. Here, full priority is given to actuality (construed as a mode of the immanent reality self-reflectively being itself) over formal constructs. The characteristic aporias of this variety of "Copernican revolution" are discussed.

  13. Experimental and computational surface and flow-field results for an all-body hypersonic aircraft

    NASA Technical Reports Server (NTRS)

    Lockman, William K.; Lawrence, Scott L.; Cleary, Joseph W.

    1990-01-01

    The objective of the present investigation is to establish a benchmark experimental data base for a generic hypersonic vehicle shape for validation and/or calibration of advanced computational fluid dynamics computer codes. This paper includes results from the comprehensive test program conducted in the NASA/Ames 3.5-foot Hypersonic Wind Tunnel for a generic all-body hypersonic aircraft model. Experimental and computational results on flow visualization, surface pressures, surface convective heat transfer, and pitot-pressure flow-field surveys are presented. Comparisons of the experimental results with computational results from an upwind parabolized Navier-Stokes code developed at Ames demonstrate the capabilities of this code.

  14. Linguistic Theory and Actual Language.

    ERIC Educational Resources Information Center

    Segerdahl, Par

    1995-01-01

    Examines Noam Chomsky's (1957) discussion of "grammaticalness" and the role of linguistics in the "correct" way of speaking and writing. It is argued that the concern of linguistics with the tools of grammar has resulted in confusion, with the tools becoming mixed up with the actual language, thereby becoming the central element in a metaphysical…

  15. Comparison of simulated and actual wind shear radar data products

    NASA Technical Reports Server (NTRS)

    Britt, Charles L.; Crittenden, Lucille H.

    1992-01-01

    Prior to the development of the NASA experimental wind shear radar system, extensive computer simulations were conducted to determine the performance of the radar in combined weather and ground clutter environments. The simulation of the radar used analytical microburst models to determine weather returns and synthetic aperture radar (SAR) maps to determine ground clutter returns. These simulations were used to guide the development of hazard detection algorithms and to predict their performance. The structure of the radar simulation is reviewed. Actual flight data results from the Orlando and Denver tests are compared with simulated results. Areas of agreement and disagreement of actual and simulated results are shown.

  16. Experimental results from containment piping bellows subjected to severe accident conditions: Results from bellows tested in corroded conditions. Volume 2

    SciTech Connect

    Lambert, L.D.; Parks, M.B.

    1995-10-01

    Bellows are an integral part of the containment pressure boundary in nuclear power plants. They are used at piping penetrations to allow relative movement between piping and the containment wall, while minimizing the load imposed on the piping and wall. Piping bellows are primarily used in steel containments; however, they have received limited use in some concrete (reinforced and prestressed) containments. In a severe accident they may be subjected to pressure and temperature conditions that exceed the design values, along with a combination of axial and lateral deflections. A test program to determine the leak-tight capacity of containment penetration bellows is being conducted at Sandia National Laboratories under the sponsorship of the US Nuclear Regulatory Commission. Several different bellows geometries, representative of actual containment bellows, have been subjected to extreme deflections along with pressure and temperature loads. The bellows geometries and loading conditions are described along with the testing apparatus and procedures. A total of nineteen bellows have been tested. Thirteen bellows were tested in ``like-new`` condition (results reported in Volume 1), and six were tested in a corroded condition. The tests showed that bellows in ``like-new`` condition are capable of withstanding relatively large deformations, up to, or near, the point of full compression or elongation, before developing leakage, while those in a corroded condition did not perform as well, depending on the amount of corrosion. The corroded bellows test program and results are presented in this report.

  17. Experimental Results of Plasma Induced EMI Effects in a Reflector Antenna System

    NASA Astrophysics Data System (ADS)

    Bandinelli, M.; Pandolfo, L.; Sarri, A.; Fittipaldi, D. A.; Pawlak, H.; Marliani, F.

    2012-05-01

    This paper presents measurement results of the electromagnetic interference (EMI) caused by the plasma plume of ion thrusters firing through the RF beam of reflector antennas. The EMI effect consists mainly in the introduction of discrete spurious modulation products on the RF carrier thus degrading spectral purity. The measurements were carried out on a mockup which is geometrically representative of the actual SGEO spacecraft design. The mockup and the acquisition system were specifically designed to allow RF measurements inside a metallic vacuum chamber. Three ion thrusters were characterised during the test campaign: SPT-100, HEMP-T, PPS-1350.

  18. Toxicology of chemical mixtures: experimental approaches, underlying concepts, and some results.

    PubMed

    Yang, R S; Hong, H L; Boorman, G A

    1989-12-01

    The toxicology of chemical mixtures will be the toxicology of the 1990s and beyond. While this branch of toxicology most closely reflects the actual human exposure situation, there is yet no standard protocol or consensus methodology for investigating the toxicology of mixtures. Thus, in this emerging science, experimentation is required just to develop a broadly applicable evaluation system. Several examples are discussed to illustrate the different experimental designs and the concepts behind each. These include the health effects studies of Love Canal soil samples, the Lake Ontario Coho salmon, the water samples repurified from secondary sewage in the city of Denver Potable Water Reuse Demonstration Plant, and the National Toxicology Program (NTP) effort on a mixture of 25 frequently detected groundwater contaminants derived from hazardous waste disposal sites. In the last instance, an extensive research program has been ongoing for the last 2 years at the NTP, encompassing general toxicology, immunotoxicology, developmental and reproductive toxicology, biochemical toxicology, myelotoxicology, genetic toxicology, neurobehavioral toxicology, and hepato- and renal toxicology. PMID:2690403

  19. Toxicology of chemical mixtures: Experimental approaches, underlying concepts, and some results

    SciTech Connect

    Yang, R.S.; Long, H.L.; Boorman, G.A.

    1990-07-01

    The toxicology of chemical mixtures will be the toxicology of the 1990s and beyond. While this branch of toxicology most closely reflects the actual human exposure situation, as yet there is no standard protocol or consensus methodology for investigating the toxicology of mixtures. Thus, in this emerging science, experimentation is required just to develop a broadly applicable evaluation system. Several examples are discussed to illustrate the different experimental designs and the concepts behind each. These include the health effects studies of Love Canal soil samples, the Lake Ontario Coho salmon, the water samples repurified from secondary sewage in the city of Denver Potable Water Reuse Demonstration Plant, and the National Toxicology Program (NTP) effort on a mixture of 25 frequently detected groundwater contaminants derived from hazardous waste disposal sites. In the last instance, an extensive research program has been ongoing for the last two years at the NTP, encompassing general toxicology, immunotoxicology, developmental and reproductive toxicology, biochemical toxicology, myelotoxicology, genetic toxicology, neurobehavioral toxicology, and hepato- and renal toxicology.

  20. Coupled helicopter rotor/body aeromechanical stability comparison of theoretical and experimental results

    NASA Technical Reports Server (NTRS)

    Friedmann, P. P.; Venkatesan, C.

    1985-01-01

    This paper presents the results of an analytical study aimed at predicting the aeromechanical stability of a helicopter in ground resonance, with the inclusions of aerodynamic forces. The theoretical results are found to be in good agreement with the experimental results, available in the literature, indicating that the coupled rotor/fuselage system can be represented by a reasonably simple mathmatical model.

  1. Comparison of experimental coupled helicopter rotor/body stability results with a simple analytical model

    NASA Technical Reports Server (NTRS)

    Friedmann, P. P.; Venkatesan, C.

    1988-01-01

    The results of an analytical study aimed at predicting the aeromechanical stability of a helicopter in ground resonance, with the inclusion of aerodynamic forces are presented. The theoretical results are found to be in good agreement with the experimental results, available in literature, indicating that the coupled rotor/fuselage system can be represented by a reasonably simple mathematical model.

  2. Experimental study of tilting-pad journal bearings - Comparison with theoretical thermoelastohydrodynamic results

    NASA Astrophysics Data System (ADS)

    Fillon, Michel; Bligoud, Jean-Claude; Frene, Jean

    1992-07-01

    Operating characteristics of four-shoe tilting-pad journal bearings of 100 mm diameter and 70 mm length are determined on an experimental device. The load, between pad configuration, varies from 0 to 10,000 N and the rotational speed is up to 4000 rpm. Forty thermocouples are used in order to measure bearing element temperatures (babbitt, shaft, housing and oil baths). The influence of operating conditions and preload ratio on bearing performances are studied. Comparison between theoretical and experimental results is presented. The theoretical model is also performed on a large tilting-pad journal bearing which was investigated experimentally by other authors.

  3. Performance analysis of wick-assisted heat pipe solar collector and comparison with experimental results

    NASA Astrophysics Data System (ADS)

    Azad, E.

    2009-03-01

    The performance of heat pipe solar collector is investigated theoretically and experimentally. The system employs wick-assisted heat pipe for the heat transfer from the absorber (evaporator) to a heat exchanger (condenser). The heat pipe is made with a copper tube and the evaporator section is finned with aluminium plate. Theoretical model predicts the outlet water from heat exchanger, heat pipe temperature and also the thermal efficiency of solar collector. The results are compared with experimental data.

  4. The first experimental results from x-ray imaging crystal spectrometer for KSTAR

    SciTech Connect

    Lee, S. G.; Bak, J. G.; Nam, U. W.; Moon, M. K.; Shi, Y.; Bitter, M.; Hill, K.

    2010-10-15

    The x-ray imaging crystal spectrometer (XICS) for the Korea Superconducting Tokamak Advanced Research has been first applied for the experimental campaign in 2009. The XICS was designed to provide measurements of the profiles of the ion and electron temperatures from the heliumlike argon (Ar XVII) spectra. The basic functions of the XICS are properly working although some satellites lines are not well matched with the expected theoretical values. The initial experimental results from the XICS are briefly described.

  5. Psychoneuroimmunology: an interpretation of experimental and case study evidence towards a paradigm for predictable results.

    PubMed

    Kalt, H W

    2000-07-01

    This paper surveys a number of key experiments and case studies relating to psychoneuroimmunology. It finds that most techniques to influence or even direct the immune system via the mind fall into a series of theoretical categories called passive, active and targeted effects. By examining the results of experiments and studies in the light of these categories a number of important conclusions are drawn. These conclusions explain differences in experimental results, describe those variables that appear to be central to obtaining results, and describe in detail where experimentation should be concentrated to further knowledge of psychoneuroimmunology.

  6. Performance of semirigid timber frame with Lagscrewbolt connections: experimental, analytical, and numerical model results

    NASA Astrophysics Data System (ADS)

    Mori, Takuro; Nakatani, Makoto; Tesfamariam, Solomon

    2015-12-01

    This paper presents analytical and numerical models for semirigid timber frame with Lagscrewbolt (LSB) connections. A series of static and reverse cyclic experimental tests were carried out for different beam sizes (400, 500, and 600 mm depth) and column-base connections with different numbers of LSBs (4, 5, 8). For the beam-column connections, with increase in beam depth, moment resistance and stiffness values increased, and ductility factor reduced. For the column-base connection, with increase in the number of LSBs, the strength, stiffness, and ductility values increased. A material model available in OpenSees, Pinching4 hysteretic model, was calibrated for all connection test results. Finally, analytical model of the portal frame was developed and compared with the experimental test results. Overall, there was good agreement with the experimental test results, and the Pinching4 hysteretic model can readily be used for full-scale structural model.

  7. Comparison of kinetic theory predictions with experimental results for a vibrated three-dimensional granular bed

    NASA Astrophysics Data System (ADS)

    Viswanathan, H.; Wildman, R. D.; Huntley, J. M.; Martin, T. W.

    2006-11-01

    The three-dimensional conservation equations relating energy and momentum transfer in a vibrated three-dimensional granular bed have been solved numerically by the finite element method. Two closures based on granular kinetic theory were used: one, the standard Fourier law relating heat flux to temperature gradient and the other, including an additional concentration gradient term. Each prediction of the two-dimensional axisymmetric granular temperature and packing fraction fields was compared against a one-dimensional model and three-dimensional experimental results, acquired using the technique of positron emission particle tracking. Both closures resulted in solutions that were in reasonable agreement with the experimental results, but it was found that differences between the predictions of each of the closures were relatively small in comparison to the anisotropy of the experimentally determined temperature distribution.

  8. Pilot Eye Scanning under Actual Single Pilot Instrument Flight

    NASA Astrophysics Data System (ADS)

    Rinoie, Kenichi; Sunada, Yasuto

    Operations under single pilot instrument flight rules for general aviation aircraft is known to be one of the most demanding pilot tasks. Scanning numerous instruments plays a key role for perception and decision-making during flight. Flight experiments have been done by a single engine light airplane to investigate the pilot eye scanning technique for IFR flights. Comparisons between the results by an actual flight and those by a PC-based flight simulator are made. The experimental difficulties of pilot eye scanning measurements during the actual IFR flight are discussed.

  9. Armature reaction effects on a high temperature superconducting field winding of an synchronous machine: experimental results

    NASA Astrophysics Data System (ADS)

    Mijatovic, Nenad; Jensen, Bogi Bech

    2014-05-01

    This paper presents experimental results from the Superwind laboratory setup. Particular focus in the paper has been placed on describing and quantifying the influence of armature reaction on performance of the HTS filed winding. Presented experimental results have confirmed the HTS field winding sensitivity to both armature reaction intensity and angular position with respect to the HTS coils. Furthermore, the characterization of the HTS field winding has been correlated to the electromagnetic torque of the machine where the maximal Ic reduction of 21% has been observed for the maximum torque.

  10. Three-dimensional convection in horizontal cylinders - Numerical solutions and comparison with experimental and analytical results

    NASA Technical Reports Server (NTRS)

    Smutek, C.; Bontoux, P.; Roux, B.; Schiroky, G. H.; Hurford, A. C.

    1985-01-01

    The results of a three-dimensional numerical simulation of Boussinesq free convection in a horizontal differentially heated cylinder are presented. The computation was based on a Samarskii-Andreyev scheme (described by Leong, 1981) and a false-transient advancement in time, with vorticity, velocity, and temperature as dependent variables. Solutions for velocity and temperature distributions were obtained for Rayleigh numbers (based on the radius) Ra = 74-18,700, thus covering the core- and boundary-layer-driven regimes. Numerical solutions are compared with asymptotic analytical solutions and experimental data. The numerical results well represent the complex three-dimensional flows found experimentally.

  11. Preliminary Experimental Results on Controlled Cardiac Computed Tomography: A Phantom Study

    PubMed Central

    Lu, Yang; Cai, Zhijun; Wang, Ge; Zhao, Jun; Bai, Er-Wei

    2010-01-01

    In this paper, we present the preliminary experimental results on controlled cardiac computed tomography (CT), which aims to reduce the motion artifacts by means of controlling the x-ray source rotation speed. An innovative cardiac phantom enables us to perform this experiment without modifying the scanner. It is the first experiment on the cardiac CT with speed controlled x-ray source. Experimental results demonstrate that the proposed method successfully separates the phantom images at different phases (improve the temporal resolution) though controlling the x-ray speed. PMID:19696470

  12. Comparison of energy deposition calculations by the LAHET Code System with experimental results

    SciTech Connect

    Beard, C.A.; Lisowski, P.W.; Russell, G.J.; Waters, L.S.

    1993-08-01

    A comparison was performed between the energy deposition predicted by the LAHET Code System (LCS) with experimental values determined by Belyakov-Bodin et al. for 800, 1000, and 1200 MeV protons on targets composed of lead, bismuth, beryllium, carbon, and aluminum. The lead and bismuth showed agreement within approximately 10% at locations throughout the targets, and the agreement of the total energy deposited over the axial length of the targets ranged from 1% to 25%. For the lead and bismuth cases, the LCS predictions were always greater than the experimental results. For the lighter materials, the agreement at locations throughout the target only agreed within approximately 20%. No definable trend could be determined for the lighter materials since some LCS predictions were greater than the experimental results, some were less than the experimental results, and some showed very good agreement. The total energy deposited over the axial length of the targets was not compared for the lighter materials since it was not explicitly given with the experimental data.

  13. At Odds: Reconciling Experimental and Theoretical Results in High School Physics

    ERIC Educational Resources Information Center

    Gates, Joshua

    2009-01-01

    For this experiment, students are divided into 2 groups and presented with a static equilibrium force-balance problem to solve. One group works entirely experimentally and the other group theoretically, using Newton's laws. The groups present their seemingly dissimilar results and must reconcile them through discussion. (Contains 3 figures.)

  14. An outcome-based learning model to identify emerging threats : experimental and simulation results.

    SciTech Connect

    Martinez-Moyano, I. J.; Conrad, S. H.; Andersen, D. F.; Decision and Information Sciences; SNL; Univ. at Albany

    2007-01-01

    The authors present experimental and simulation results of an outcome-based learning model as it applies to the identification of emerging threats. This model integrates judgment, decision making, and learning theories to provide an integrated framework for the behavioral study of emerging threats.

  15. Photon Detection with Cooled Avalanche Photodiodes: Theory and Preliminary Experimental Results

    NASA Technical Reports Server (NTRS)

    Robinson, D. L.; Hays, D. A.

    1985-01-01

    Avalanche photodiodes (APDs) can be operated in a geiger-tube mode so that they can respond to single electron events and thus be used as photon counting detectors. Operational characteristics and theory of APDs while used in this mode are analyzed and assessed. Preliminary experimental investigation of several commercially available APDs has commenced, and initial results for dark count statistics are presented.

  16. Simulation and experimental results of kaleidoscope homogenizers for longitudinal diode pumping.

    PubMed

    Bartnicki, Eric; Bourdet, Gilbert L

    2010-03-20

    With the goal to set a homogenizer to allow coupling of a stack of diodes with a disk amplifier medium for a longitudinally pumped laser or amplifier, we report simulation and experimental results on homogenization of the light supplied by a large stack of diodes. We investigate various kaleidoscope cross-section shapes and various optical coupling configurations.

  17. Experimental results concerning global observables from the CERN SPS heavy ion program

    SciTech Connect

    Young, G.R.

    1990-06-01

    A brief overview is given of experimental results obtained during the initial operation of the heavy-ion program at the CERN SPS during the period 1986--1988. This paper confines itself to a presentation of results on so-called global observables, such as energy flow and multiplicity distributions, and on information extracted from them. Of particular interest among the latter are an estimate of the magnitude and spatial distribution of the energy density attained. 3 refs., 27 figs.

  18. Phase transition kinetics in DIET of vanadium pentoxide. I. Experimental results

    NASA Astrophysics Data System (ADS)

    Ai, R.; Fan, H.-J.; Marks, L. D.

    1993-01-01

    Experimental results of the kinetics of phase transformation in vanadium pentoxide during surface loss of oxygen from electron irradiation are described. Phase transformations under three different regimes were examined: (a) low flux; (b) intermediate flux and (c) high flux. Different phase transformation routes were observed under different fluxes. In a companion paper, numerical calculations are presented demonstrating that these results are due to a mixed interface/diffusion controlled phase transition pumped by surface oxygen loss.

  19. Applying computational methods to interpret experimental results in tribology and enantioselective catalysis

    NASA Astrophysics Data System (ADS)

    Garvey, Michael T.

    Computational methods are rapidly becoming a mainstay in the field of chemistry. Advances in computational methods (both theory and implementation), increasing availability of computational resources and the advancement of parallel computing are some of the major forces driving this trend. It is now possible to perform density functional theory (DFT) calculations with chemical accuracy for model systems that can be interrogated experimentally. This allows computational methods to supplement or complement experimental methods. There are even cases where DFT calculations can give insight into processes and interactions that cannot be interrogated directly by current experimental methods. This work presents several examples of the application of computational methods to the interpretation and analysis of experimentally obtained results. First, triobological systems were investigated primarily with full-potential linearized augmented plane wave (FLAPW) method DFT calculations. Second, small organic molecules adsorbed on Pd(111) were studied using projector-augmented wave (PAW) method DFT calculations and scanning tunneling microscopy (STM) image simulations to investigate molecular interactions involved in enantioselective heterogeneous catalysis. A method for method for calculating pressure-dependent shear properties of model boundary-layer lubricants is demonstrated. The calculated values are compared with experimentally obtained results. For the case of methyl pyruvate adsorbed on Pd(111), DFT-calculated adsorption energies and structures are used along with STM simulations to identify species observed by STM imaging. A previously unobserved enol species is discovered to be present along with the expected keto species. The information about methyl pyruvate species on Pd(111) is combined with previously published studies of S-alpha-(1-naphthyl)-ethylamine (NEA) to understand the nature of their interaction upon coadsorption on Pd(111). DFT calculated structures and

  20. Automated detection of discourse segment and experimental types from the text of cancer pathway results sections.

    PubMed

    Burns, Gully A P C; Dasigi, Pradeep; de Waard, Anita; Hovy, Eduard H

    2016-01-01

    Automated machine-reading biocuration systems typically use sentence-by-sentence information extraction to construct meaning representations for use by curators. This does not directly reflect the typical discourse structure used by scientists to construct an argument from the experimental data available within a article, and is therefore less likely to correspond to representations typically used in biomedical informatics systems (let alone to the mental models that scientists have). In this study, we develop Natural Language Processing methods to locate, extract, and classify the individual passages of text from articles' Results sections that refer to experimental data. In our domain of interest (molecular biology studies of cancer signal transduction pathways), individual articles may contain as many as 30 small-scale individual experiments describing a variety of findings, upon which authors base their overall research conclusions. Our system automatically classifies discourse segments in these texts into seven categories (fact, hypothesis, problem, goal, method, result, implication) with an F-score of 0.68. These segments describe the essential building blocks of scientific discourse to (i) provide context for each experiment, (ii) report experimental details and (iii) explain the data's meaning in context. We evaluate our system on text passages from articles that were curated in molecular biology databases (the Pathway Logic Datum repository, the Molecular Interaction MINT and INTACT databases) linking individual experiments in articles to the type of assay used (coprecipitation, phosphorylation, translocation etc.). We use supervised machine learning techniques on text passages containing unambiguous references to experiments to obtain baseline F1 scores of 0.59 for MINT, 0.71 for INTACT and 0.63 for Pathway Logic. Although preliminary, these results support the notion that targeting information extraction methods to experimental results could provide

  1. Automated detection of discourse segment and experimental types from the text of cancer pathway results sections.

    PubMed

    Burns, Gully A P C; Dasigi, Pradeep; de Waard, Anita; Hovy, Eduard H

    2016-01-01

    Automated machine-reading biocuration systems typically use sentence-by-sentence information extraction to construct meaning representations for use by curators. This does not directly reflect the typical discourse structure used by scientists to construct an argument from the experimental data available within a article, and is therefore less likely to correspond to representations typically used in biomedical informatics systems (let alone to the mental models that scientists have). In this study, we develop Natural Language Processing methods to locate, extract, and classify the individual passages of text from articles' Results sections that refer to experimental data. In our domain of interest (molecular biology studies of cancer signal transduction pathways), individual articles may contain as many as 30 small-scale individual experiments describing a variety of findings, upon which authors base their overall research conclusions. Our system automatically classifies discourse segments in these texts into seven categories (fact, hypothesis, problem, goal, method, result, implication) with an F-score of 0.68. These segments describe the essential building blocks of scientific discourse to (i) provide context for each experiment, (ii) report experimental details and (iii) explain the data's meaning in context. We evaluate our system on text passages from articles that were curated in molecular biology databases (the Pathway Logic Datum repository, the Molecular Interaction MINT and INTACT databases) linking individual experiments in articles to the type of assay used (coprecipitation, phosphorylation, translocation etc.). We use supervised machine learning techniques on text passages containing unambiguous references to experiments to obtain baseline F1 scores of 0.59 for MINT, 0.71 for INTACT and 0.63 for Pathway Logic. Although preliminary, these results support the notion that targeting information extraction methods to experimental results could provide

  2. Automated detection of discourse segment and experimental types from the text of cancer pathway results sections

    PubMed Central

    Burns, Gully A.P.C.; Dasigi, Pradeep; de Waard, Anita; Hovy, Eduard H.

    2016-01-01

    Automated machine-reading biocuration systems typically use sentence-by-sentence information extraction to construct meaning representations for use by curators. This does not directly reflect the typical discourse structure used by scientists to construct an argument from the experimental data available within a article, and is therefore less likely to correspond to representations typically used in biomedical informatics systems (let alone to the mental models that scientists have). In this study, we develop Natural Language Processing methods to locate, extract, and classify the individual passages of text from articles’ Results sections that refer to experimental data. In our domain of interest (molecular biology studies of cancer signal transduction pathways), individual articles may contain as many as 30 small-scale individual experiments describing a variety of findings, upon which authors base their overall research conclusions. Our system automatically classifies discourse segments in these texts into seven categories (fact, hypothesis, problem, goal, method, result, implication) with an F-score of 0.68. These segments describe the essential building blocks of scientific discourse to (i) provide context for each experiment, (ii) report experimental details and (iii) explain the data’s meaning in context. We evaluate our system on text passages from articles that were curated in molecular biology databases (the Pathway Logic Datum repository, the Molecular Interaction MINT and INTACT databases) linking individual experiments in articles to the type of assay used (coprecipitation, phosphorylation, translocation etc.). We use supervised machine learning techniques on text passages containing unambiguous references to experiments to obtain baseline F1 scores of 0.59 for MINT, 0.71 for INTACT and 0.63 for Pathway Logic. Although preliminary, these results support the notion that targeting information extraction methods to experimental results could provide

  3. Temperature dependence of spectral induced polarization data: experimental results and membrane polarization theory

    NASA Astrophysics Data System (ADS)

    Bairlein, Katharina; Bücker, Matthias; Hördt, Andreas; Hinze, Björn

    2016-04-01

    Spectral induced polarization measurements are affected by temperature variations due to a variety of temperature-dependent parameters that control the complex electrical conductivity. Most important is the influence of the ion mobility, which increases with increasing temperature. It is responsible for the increase of the conductivity of the fluid in the pores with temperature and influences the electrical double layer on the mineral surface. This work is based on laboratory measurements of 13 sandstone samples from different sources with different geological and petrophysical characteristics. We measured the complex impedance in a frequency range from 0.01 to 100 Hz and a temperature range from 0 to 40 °C. The main observation is a decrease of the characteristic time (defined by the inverse of the frequency, at which the phase shift is maximum) with increasing temperature. The strength of this decrease differs from one sample to another. The temperature dependence of the phase shift magnitude cannot easily be generalized, as it depends on the particular sample. The experimental findings suggest that neglecting the influence of temperature on complex conductivity may lead to significant errors when estimating hydraulic conductivity from relaxation time. We also simulate the temperature dependence with a theoretical model of membrane polarization and review some of the model properties, with an emphasis on the temperature dependence of the parameters. The model reproduces several features characterizing the measured data, including the temperature dependence of the characteristic times. Computed tomography and microscope images of the pore structure of three samples also allow us to associate differences in the geometrical parameters used in the modelling with pore scale parameters of the actual samples.

  4. Propagation effects for land mobile satellite systems: Overview of experimental and modeling results

    NASA Technical Reports Server (NTRS)

    Goldhirsh, Julius; Vogel, Wolfhard J.

    1992-01-01

    Models developed and experiments performed to characterize the propagation environment associated with land mobile communication using satellites are discussed. Experiments were carried out with transmitters on stratospheric balloons, remotely piloted aircraft, helicopters, and geostationary satellites. This text is comprised of compiled experimental results for the expressed use of communications engineers, designers of planned Land Mobile Satellite Systems (LMSS), and modelers of propagation effects. The results presented here are mostly derived from systematic studies of propagation effects for LMSS geometries in the United States associated with rural and suburban regions. Where applicable, the authors also draw liberally from the results of other related investigations in Canada, Europe, and Australia. Frequencies near 1500 MHz are emphasized to coincide with frequency bands allocated for LMSS by the International Telecommunication Union, although earlier experimental work at 870 MHz is also included.

  5. Numerical predictions and experimental results of a dry bay fire environment.

    SciTech Connect

    Suo-Anttila, Jill Marie; Gill, Walter; Black, Amalia Rebecca

    2003-11-01

    The primary objective of the Safety and Survivability of Aircraft Initiative is to improve the safety and survivability of systems by using validated computational models to predict the hazard posed by a fire. To meet this need, computational model predictions and experimental data have been obtained to provide insight into the thermal environment inside an aircraft dry bay. The calculations were performed using the Vulcan fire code, and the experiments were completed using a specially designed full-scale fixture. The focus of this report is to present comparisons of the Vulcan results with experimental data for a selected test scenario and to assess the capability of the Vulcan fire field model to accurately predict dry bay fire scenarios. Also included is an assessment of the sensitivity of the fire model predictions to boundary condition distribution and grid resolution. To facilitate the comparison with experimental results, a brief description of the dry bay fire test fixture and a detailed specification of the geometry and boundary conditions are included. Overall, the Vulcan fire field model has shown the capability to predict the thermal hazard posed by a sustained pool fire within a dry bay compartment of an aircraft; although, more extensive experimental data and rigorous comparison are required for model validation.

  6. IFNAR signaling directly modulates T lymphocyte activity, resulting in milder experimental autoimmune encephalomyelitis development.

    PubMed

    Kavrochorianou, Nadia; Evangelidou, Maria; Markogiannaki, Melina; Tovey, Michael; Thyphronitis, George; Haralambous, Sylva

    2016-01-01

    Although interferon-β is used as first-line therapy for multiple sclerosis, the cell type-specific activity of type I interferons in multiple sclerosis and its animal model, experimental autoimmune encephalomyelitis, remains obscure. In this study, we have elucidated the in vivo immunomodulatory role of type I interferon signaling in T cells during experimental autoimmune encephalomyelitis by use of a novel transgenic mouse, carrying a cd2-ifnar1 transgene on a interferon-α/β receptor 1 null genetic background, thus allowing expression of the interferon-α/β receptor 1 and hence, a functional type I interferon receptor exclusively on T cells. These transgenic mice exhibited milder experimental autoimmune encephalomyelitis with reduced T cell infiltration, demyelination, and axonal damage in the central nervous system. It is noteworthy that interferon-β administration in transgenic mice generated a more pronounced, protective effect against experimental autoimmune encephalomyelitis compared with untreated littermates. In vivo studies demonstrated that before experimental autoimmune encephalomyelitis onset, endogenous type I interferon receptor signaling in T cells led to impaired T-helper 17 responses, with a reduced fraction of CCR6(+) CD4(+) T cells in the periphery. At the acute phase, an increased proportion of interleukin-10- and interferon-γ-producing CD4(+) T cells was detected in the periphery of the transgenic mice, accompanied by up-regulation of the interferon-γ-induced gene Irgm1 in peripheral T cells. Together, these results reveal a hitherto unknown T cell-associated protective role of type I interferon in experimental autoimmune encephalomyelitis that may provide valuable clues for designing novel therapeutic strategies for multiple sclerosis.

  7. IFNAR signaling directly modulates T lymphocyte activity, resulting in milder experimental autoimmune encephalomyelitis development.

    PubMed

    Kavrochorianou, Nadia; Evangelidou, Maria; Markogiannaki, Melina; Tovey, Michael; Thyphronitis, George; Haralambous, Sylva

    2016-01-01

    Although interferon-β is used as first-line therapy for multiple sclerosis, the cell type-specific activity of type I interferons in multiple sclerosis and its animal model, experimental autoimmune encephalomyelitis, remains obscure. In this study, we have elucidated the in vivo immunomodulatory role of type I interferon signaling in T cells during experimental autoimmune encephalomyelitis by use of a novel transgenic mouse, carrying a cd2-ifnar1 transgene on a interferon-α/β receptor 1 null genetic background, thus allowing expression of the interferon-α/β receptor 1 and hence, a functional type I interferon receptor exclusively on T cells. These transgenic mice exhibited milder experimental autoimmune encephalomyelitis with reduced T cell infiltration, demyelination, and axonal damage in the central nervous system. It is noteworthy that interferon-β administration in transgenic mice generated a more pronounced, protective effect against experimental autoimmune encephalomyelitis compared with untreated littermates. In vivo studies demonstrated that before experimental autoimmune encephalomyelitis onset, endogenous type I interferon receptor signaling in T cells led to impaired T-helper 17 responses, with a reduced fraction of CCR6(+) CD4(+) T cells in the periphery. At the acute phase, an increased proportion of interleukin-10- and interferon-γ-producing CD4(+) T cells was detected in the periphery of the transgenic mice, accompanied by up-regulation of the interferon-γ-induced gene Irgm1 in peripheral T cells. Together, these results reveal a hitherto unknown T cell-associated protective role of type I interferon in experimental autoimmune encephalomyelitis that may provide valuable clues for designing novel therapeutic strategies for multiple sclerosis. PMID:26232452

  8. Microstructure-based calculations and experimental results for sound absorbing porous layers of randomly packed rigid spherical beads

    NASA Astrophysics Data System (ADS)

    Zieliński, Tomasz G.

    2014-07-01

    Acoustics of stiff porous media with open porosity can be very effectively modelled using the so-called Johnson-Champoux-Allard-Pride-Lafarge model for sound absorbing porous media with rigid frame. It is an advanced semi-phenomenological model with eight parameters, namely, the total porosity, the viscous permeability and its thermal analogue, the tortuosity, two characteristic lengths (one specific for viscous forces, the other for thermal effects), and finally, viscous and thermal tortuosities at the frequency limit of 0 Hz. Most of these parameters can be measured directly, however, to this end specific equipment is required different for various parameters. Moreover, some parameters are difficult to determine. This is one of several reasons for the so-called multiscale approach, where the parameters are computed from specific finite-element analyses based on some realistic geometric representations of the actual microstructure of porous material. Such approach is presented and validated for layers made up of loosely packed small identical rigid spheres. The sound absorption of such layers was measured experimentally in the impedance tube using the so-called two-microphone transfer function method. The layers are characterised by open porosity and semi-regular microstructure: the identical spheres are loosely packed by random pouring and mixing under the gravity force inside the impedance tubes of various size. Therefore, the regular sphere packings were used to generate Representative Volume Elements suitable for calculations at the micro-scale level. These packings involve only one, two, or four spheres so that the three-dimensional finite-element calculations specific for viscous, thermal, and tortuous effects are feasible. In the proposed geometric packings, the spheres were slightly shifted in order to achieve the correct value of total porosity which was precisely estimated for the layers tested experimentally. Finally, in this paper some results based on

  9. Analysis of very high frequency propagation in sediments: Experimental results and modeling

    NASA Astrophysics Data System (ADS)

    Brothers, Richard; Page, Sarah; Heald, Gary; Leighton, Tim; Simpson, Matt; Dix, Justin

    2002-11-01

    A current QinetiQ study is investigating the propagation of sound waves into sediment at frequencies higher than 300 kHz. Previous work has found notable discrepancies between model predictions and experimental results and comparisons are inconsistent and unreliable. This new work package investigates the development of new scattering theories for frequencies ranging from 300 kHz to 1 MHz. In particular, the application of a pseudospectral time difference approached is analyzed. The model originally developed for lower frequency applications, is set up in various geometrical scenarios and for varying very high frequencies. Results show the received simulated pulses obtained for hydrophones placed within the sediment and source colocated. Furthermore, simulations are compared in tank experimental data. The controlled tank experiments were conducted by Southampton University and data are analyzed and discussed for various conditions and frequencies.

  10. Gradual ordering in mollusk shell nacre: theoretical modeling and experimental results

    NASA Astrophysics Data System (ADS)

    Coppersmith, Susan N.

    2013-03-01

    Biominerals have attracted the attention of materials scientists, biologists, and mineralogists as well as physicists because of their remarkable mechanical properties and incompletely elucidated formation mechanisms. Nacre, or mother-of-pearl, is a layered biomineral composite that is widely studied because of its self-assembled, efficient and accurately ordered architecture results in remarkable resistance to fracture. New experimental tools enable us to obtain new information about the organization and structure of the mineral tablets in nacre. Our experimental and theoretical investigations yield strong evidence that orientational ordering of these tablets is the result of dynamical self-organization. This work was supported by NSF award CHE&DMR-0613972, DOE award DE-FG02-07ER15899, UW-Graduate School Vilas Award to P.U.P.A. Gilbert, and NSF awards DMR-0209630 and DMR-0906951 to SNC.

  11. Advanced Supersonic Nozzle Concepts: Experimental Flow Visualization Results Paired With LES

    NASA Astrophysics Data System (ADS)

    Berry, Matthew; Magstadt, Andrew; Stack, Cory; Gaitonde, Datta; Glauser, Mark; Syracuse University Team; The Ohio State University Team

    2015-11-01

    Advanced supersonic nozzle concepts are currently under investigation, utilizing multiple bypass streams and airframe integration to bolster performance and efficiency. This work focuses on the parametric study of a supersonic, multi-stream jet with aft deck. The single plane of symmetry, rectangular nozzle, displays very complex and unique flow characteristics. Flow visualization techniques in the form of PIV and schlieren capture flow features at various deck lengths and Mach numbers. LES is compared to the experimental results to both validate the computational model and identify limitations of the simulation. By comparing experimental results to LES, this study will help create a foundation of knowledge for advanced nozzle designs in future aircraft. SBIR Phase II with Spectral Energies, LLC under direction of Barry Kiel.

  12. REFLECTIONS ON MY CONTRIBUTIONS TO PARTICLE PHYSICS AND RECENT EXPERIMENTAL RESULTS FROM RHIC.

    SciTech Connect

    SAMIOS,N.P.

    2002-01-18

    My talk today will be composed of two parts. The first part will consist of a summary of some of my experimental contributions over the years. It will not be exhaustive but will highlight the findings that had relevance to the progress of our understanding of particle physics as it has evolved over the years. This section will be divided into three periods: Early, Intermediate and Late, with an in depth discussion of a few of the more significant results. The second part will consist of a discussion of the recently completed Relativistic Heavy Ion Collider (RHIC) machine at Brookhaven National Laboratory (BNL). This will encompass the parameters of the accelerator and some of the interesting and exciting early experimental results emanating from this machine.

  13. Controls-structures interaction guest investigator program: Overview and phase 1 experimental results and future plans

    NASA Technical Reports Server (NTRS)

    Smith-Taylor, Rudeen; Tanner, Sharon E.

    1993-01-01

    The NASA Controls-Structures Interaction (CSI) Guest Investigator program is described in terms of its support of the development of CSI technologies. The program is based on the introduction of CSI researchers from industry and academia to available test facilities for experimental validation of technologies and methods. Phase 1 experimental results are reviewed with attention given to their use of the Mini-MAST test facility and the facility for the Advance Control Evaluation of Structures. Experiments were conducted regarding the following topics: collocated/noncollocated controllers, nonlinear math modeling, controller design, passive/active suspension systems design, and system identification and fault isolation. The results demonstrate that significantly enhanced performance from the control techniques can be achieved by integrating knowledge of the structural dynamics under consideration into the approaches.

  14. Bistatic frequency-swept microwave imaging: Principle, methodology and experimental results

    SciTech Connect

    Dingbing Lin; Tahhsiung Chu . Electrical Engineering Dept.)

    1993-05-01

    The basic principle, methodology and experimental results of frequency-swept microwave imaging of continuous shape conducting and discrete line objects in a bistatic scattering arrangement are presented. Theoretical analysis is developed under the assumptions of plane wave illumination and physical optics approximation. The measurement system and calibration procedures are implemented based on the plane wave spectrum analysis. Images of three different types of scattering objects reconstructed from the experimental data measured in the frequency range 7.5-12.5 GHz are shown in good agreement with the scattering object geometries. The results demonstrate that the developed bistatic frequency-swept microwave imaging system has potential as a cost-effective tool for the application of remote sensing, imaging radar, and nondestructive evaluation.

  15. Absorption of Fast Waves at Moderate to High Ion Cyclotron Harmonics: Experimental Results and Theoretical Models

    NASA Astrophysics Data System (ADS)

    Pinsker, R. I.; Choi, M.; Prater, R.; Heidbrink, W. W.; Luo, Y.; Baity, F. W.; Murakami, M.; Porkolab, M.

    2006-10-01

    Strong absorption of fast Alfvén waves (FW) by ion cyclotron damping has been observed in DIII-D at the 4th and 5th harmonic of an injected beam while only weak absorption is observed at the 8th harmonic. The experimental results are compared with three different theoretical models; differences between the predictions of the models suggest the possible importance of finite-width orbit effects at high harmonics. In a linear model, it is found that damping on fast ions from neutral beam injection can be significant even at the 8th harmonic under experimentally relevant conditions. This is tested in experiments in DIII-D with FW power at 60 MHz and at 116 MHz. A novel Dα charge exchange recombination diagnostic is used to observe interaction of the FW power with beam ions. The results are compared with modeling with quasilinear and with orbit-following codes.

  16. Aircrew dosimetry by means of experimental measurements and calculations: results obtained during the year 2003.

    PubMed

    Spurný, F; Bĕgusová, M; Turek, K; Vlcek, B

    2005-01-01

    The results of measurements performed during the year 2003 onboard aircraft, mostly during regular commercial flights of the Czech Airlines (CSA) are presented. The studies were performed during more than 30 individual flights, several dosemeters and equipments were used for both neutron and non-neutron components of the onboard radiation field. CSA colleagues submitted us for all flights with navigation data necessary for the calculation of onboard aircraft crew exposure with transport codes EPCARD and CARI. Direct readings of experimental equipments were corrected on the base of the calibration in CERN high-energy radiation fields. A reasonable agreement of measured and calculated data was observed. During one of the flights, a very deep Forbush decrease occurred. The experimental results confronted with calculation permitted to obtain new view on the influence of such events on aircraft crew exposure.

  17. Experimental and husbandry procedures as potential modifiers of the results of phenotyping tests.

    PubMed

    Gerdin, Anna-Karin; Igosheva, Natalia; Roberson, Laura-Anne; Ismail, Ozama; Karp, Natasha; Sanderson, Mark; Cambridge, Emma; Shannon, Carl; Sunter, David; Ramirez-Solis, Ramiro; Bussell, James; White, Jacqueline K

    2012-07-16

    To maximize the sensitivity of detecting affects of genetic variants in mice, variables have been minimized through the use of inbred mouse lines, by eliminating infectious organisms and controlling environmental variables. However, the impact of standard animal husbandry and experimental procedures on the validity of experimental data is under appreciated. In this study we monitored the impact of these procedures by using parameters that reflect stress and physiological responses to it. Short-term measures included telemetered heart rate and systolic arterial pressure, core body temperature and blood glucose, while longer-term parameters were assessed such as body weight. Male and female C57BL6/NTac mice were subjected to a range of stressors with different perceived severities ranging from repeated blood glucose and core temperature measurement procedures, intra-peritoneal injection and overnight fasting to cage transport and cage changing.Our studies reveal that common husbandry and experimental procedures significantly influence mouse physiology and behaviour. Systolic arterial pressure, heart rate, locomotor activity, core temperature and blood glucose were elevated in response to a range of experimental procedures. Differences between sexes were evident, female mice displayed more sustained cardiovascular responses and locomotor activity than male mice. These results have important implications for the design and implementation of multiple component experiments where the lasting effects of stress from previous tests may modify the outcomes of subsequent ones. PMID:22713295

  18. Experimental and husbandry procedures as potential modifiers of the results of phenotyping tests.

    PubMed

    Gerdin, Anna-Karin; Igosheva, Natalia; Roberson, Laura-Anne; Ismail, Ozama; Karp, Natasha; Sanderson, Mark; Cambridge, Emma; Shannon, Carl; Sunter, David; Ramirez-Solis, Ramiro; Bussell, James; White, Jacqueline K

    2012-07-16

    To maximize the sensitivity of detecting affects of genetic variants in mice, variables have been minimized through the use of inbred mouse lines, by eliminating infectious organisms and controlling environmental variables. However, the impact of standard animal husbandry and experimental procedures on the validity of experimental data is under appreciated. In this study we monitored the impact of these procedures by using parameters that reflect stress and physiological responses to it. Short-term measures included telemetered heart rate and systolic arterial pressure, core body temperature and blood glucose, while longer-term parameters were assessed such as body weight. Male and female C57BL6/NTac mice were subjected to a range of stressors with different perceived severities ranging from repeated blood glucose and core temperature measurement procedures, intra-peritoneal injection and overnight fasting to cage transport and cage changing.Our studies reveal that common husbandry and experimental procedures significantly influence mouse physiology and behaviour. Systolic arterial pressure, heart rate, locomotor activity, core temperature and blood glucose were elevated in response to a range of experimental procedures. Differences between sexes were evident, female mice displayed more sustained cardiovascular responses and locomotor activity than male mice. These results have important implications for the design and implementation of multiple component experiments where the lasting effects of stress from previous tests may modify the outcomes of subsequent ones.

  19. Experimental results on combined ultraviolet-proton excitation of moon rock luminescence.

    NASA Technical Reports Server (NTRS)

    Nash, D. B.

    1973-01-01

    The experimental results reported indicate that a small synergistic effect may exist between near-UV radiation and solar-wind-energy protons in solar radiation that could slightly enhance luminescence generation on the moon's surface. The magnitude of the effect, however, is far too small to account for the apparent orders-of-magnitude discrepancy between reported telescope measurements of lunar luminescence and the limitation of lunar luminescence intensity based on lab studies of moon rocks.

  20. Experimental and theoretical results on electron emission in collisions between partially dressed ions with He targets

    NASA Astrophysics Data System (ADS)

    Monti, J. M.; Fiol, J.; Fregenal, D.; Fainstein, P. D.; Rivarola, R. D.; Wolff, W.; Horsdal, E.; Bernardi, G.; Suárez, S.

    2013-09-01

    Experimental and theoretical results for electron emission in 440 keV u-1 Li+ with He targets are presented. Theoretical cross-sections are obtained using extensions of the continuum distorted wave and the continuum distorted wave-eikonal initial state models to the case of dressed projectiles and a four-body classical trajectory Monte-Carlo. The contributions of electron emission from the different aggregates of the collision system are investigated.

  1. FIRST EXPERIMENTAL RESULTS FROM DEGAS, THE QUANTUM LIMITED BRIGHTNESS ELECTRON SOURCE

    SciTech Connect

    Zolotorev, Max S.; Commins, Eugene D.; Oneill, James; Sannibale, Fernando; Tremsin, Anton; Wan, Weishi

    2008-06-23

    The construction of DEGAS (DEGenerate Advanced Source), a proof of principle for a quantum limited brightness electron source, has been completed at the Lawrence Berkeley National Laboratory. The commissioning and the characterization of this source, designed to generate coherent single electron 'bunches' with brightness approaching the quantum limit at a repetition rate of few MHz, has been started. In this paper the first experimental results are described.

  2. Optimal SNR exposure time for speckle imaging: experimental results with frequency-dependent detector noise

    NASA Astrophysics Data System (ADS)

    Tyler, David W.; Suzuki, Andrew H.; von Bokern, Mark A.; Keating, Donna D.; Roggemann, Michael C.

    1994-06-01

    We review recent arguments for using increased spectral bandwidth and exposure times to optimize the signal-to-noise ratio of speckle imaging estimators and discuss the tradeoff between camera exposure time and the number of data frames collected when observing time is fixed. We compare experimental results with a previously-derived expression for optimal exposure time and find reasonable agreement after accounting for frequency-dependent camera noise.

  3. A digital computer propulsion control facility: Description of capabilities and summary of experimental program results

    NASA Technical Reports Server (NTRS)

    Zeller, J. R.; Arpasi, D. J.; Lehtinen, B.

    1976-01-01

    Flight weight digital computers are being used today to carry out many of the propulsion system control functions previously delegated exclusively to hydromechanical controllers. An operational digital computer facility for propulsion control mode studies has been used successfully in several experimental programs. This paper describes the system and some of the results concerned with engine control, inlet control, and inlet engine integrated control. Analytical designs for the digital propulsion control modes include both classical and modern/optimal techniques.

  4. Columbus meteoroid/debris protection study - Experimental simulation techniques and results

    NASA Astrophysics Data System (ADS)

    Schneider, E.; Kitta, K.; Stilp, A.; Lambert, M.; Reimerdes, H. G.

    1992-08-01

    The methods and measurement techniques used in experimental simulations of micrometeoroid and space debris impacts with the ESA's laboratory module Columbus are described. Experiments were carried out at the two-stage light gas gun acceleration facilities of the Ernst-Mach Institute. Results are presented on simulations of normal impacts on bumper systems, oblique impacts on dual bumper systems, impacts into cooled targets, impacts into pressurized targets, and planar impacts of low-density projectiles.

  5. Estimating the hyperfine coupling parameters of the avian compass by comprehensively considering the available experimental results

    NASA Astrophysics Data System (ADS)

    Xu, Bao-Ming; Zou, Jian; Li, Jun-Gang; Shao, Bin

    2013-09-01

    Migratory birds can utilize the geomagnetic field for orientation and navigation through a widely accepted radical-pair mechanism. Although many theoretical works have been done, the available experimental results have not been fully considered, especially the temporary disorientation induced by the field which is increased by 30% of the geomagnetic field and the disorientation of the very weak resonant field of 15 nT. In this paper, we consider the monotonicity of the singlet yield angular profile as the prerequisite of direction sensitivity, and find that for some optimal values of the hyperfine coupling parameters (that is, the order of 10-7˜10-6 meV) the experimental results available so far can be satisfied. We also investigate the effects of two decoherence environments and demonstrate that, in order to satisfy the available experimental results, the decoherence rate should be lower than the recombination rate. Finally, we investigate the effects of the fluctuating magnetic noises and find that the vertical noise destroys the monotonicity of the profile completely, but the parallel noise preserves the monotonicity perfectly and even can enhance the direction sensitivity.

  6. Estimating the hyperfine coupling parameters of the avian compass by comprehensively considering the available experimental results.

    PubMed

    Xu, Bao-Ming; Zou, Jian; Li, Jun-Gang; Shao, Bin

    2013-09-01

    Migratory birds can utilize the geomagnetic field for orientation and navigation through a widely accepted radical-pair mechanism. Although many theoretical works have been done, the available experimental results have not been fully considered, especially the temporary disorientation induced by the field which is increased by 30% of the geomagnetic field and the disorientation of the very weak resonant field of 15 nT. In this paper, we consider the monotonicity of the singlet yield angular profile as the prerequisite of direction sensitivity, and find that for some optimal values of the hyperfine coupling parameters (that is, the order of 10^{-7}∼10^{-6} meV) the experimental results available so far can be satisfied. We also investigate the effects of two decoherence environments and demonstrate that, in order to satisfy the available experimental results, the decoherence rate should be lower than the recombination rate. Finally, we investigate the effects of the fluctuating magnetic noises and find that the vertical noise destroys the monotonicity of the profile completely, but the parallel noise preserves the monotonicity perfectly and even can enhance the direction sensitivity.

  7. Estimating the hyperfine coupling parameters of the avian compass by comprehensively considering the available experimental results.

    PubMed

    Xu, Bao-Ming; Zou, Jian; Li, Jun-Gang; Shao, Bin

    2013-09-01

    Migratory birds can utilize the geomagnetic field for orientation and navigation through a widely accepted radical-pair mechanism. Although many theoretical works have been done, the available experimental results have not been fully considered, especially the temporary disorientation induced by the field which is increased by 30% of the geomagnetic field and the disorientation of the very weak resonant field of 15 nT. In this paper, we consider the monotonicity of the singlet yield angular profile as the prerequisite of direction sensitivity, and find that for some optimal values of the hyperfine coupling parameters (that is, the order of 10^{-7}∼10^{-6} meV) the experimental results available so far can be satisfied. We also investigate the effects of two decoherence environments and demonstrate that, in order to satisfy the available experimental results, the decoherence rate should be lower than the recombination rate. Finally, we investigate the effects of the fluctuating magnetic noises and find that the vertical noise destroys the monotonicity of the profile completely, but the parallel noise preserves the monotonicity perfectly and even can enhance the direction sensitivity. PMID:24125290

  8. Characterisation and optimisation of flexible transfer lines for liquid helium. Part I: Experimental results

    NASA Astrophysics Data System (ADS)

    Dittmar, N.; Haberstroh, Ch.; Hesse, U.; Krzyzowski, M.

    2016-04-01

    The transfer of liquid helium (LHe) into mobile dewars or transport vessels is a common and unavoidable process at LHe decant stations. During this transfer reasonable amounts of LHe evaporate due to heat leak and pressure drop. Thus generated helium gas needs to be collected and reliquefied which requires a huge amount of electrical energy. Therefore, the design of transfer lines used at LHe decant stations has been optimised to establish a LHe transfer with minor evaporation losses which increases the overall efficiency and capacity of LHe decant stations. This paper presents the experimental results achieved during the thermohydraulic optimisation of a flexible LHe transfer line. An extensive measurement campaign with a set of dedicated transfer lines equipped with pressure and temperature sensors led to unique experimental data of this specific transfer process. The experimental results cover the heat leak, the pressure drop, the transfer rate, the outlet quality, and the cool-down and warm-up behaviour of the examined transfer lines. Based on the obtained results the design of the considered flexible transfer line has been optimised, featuring reduced heat leak and pressure drop.

  9. The 3D structure of the hadrons: recents results and experimental program at Jefferson Lab

    SciTech Connect

    Munoz Camacho, Carlos

    2014-04-01

    The understanding of Quantum Chromodynamics (QCD) at large distances still remains one of the main outstanding problems of nuclear physics. Studying the internal structure of hadrons provides a way to probe QCD in the non-perturbative domain and can help us unravel the internal structure of the most elementary blocks of matter. Jefferson Lab (JLab) has already delivered results on how elementary quarks and gluons create nucleon structure and properties. The upgrade of JLab to 12 GeV will allow the full exploration of the valence-quark structure of nucleons and the extraction of real threedimensional pictures. I will present recent results and review the future experimental program at JLab.

  10. Numerical prediction of freezing fronts in cryosurgery: comparison with experimental results.

    PubMed

    Fortin, André; Belhamadia, Youssef

    2005-08-01

    Recent developments in scientific computing now allow to consider realistic applications of numerical modelling to medicine. In this work, a numerical method is presented for the simulation of phase change occurring in cryosurgery applications. The ultimate goal of these simulations is to accurately predict the freezing front position and the thermal history inside the ice ball which is essential to determine if cancerous cells have been completely destroyed. A semi-phase field formulation including blood flow considerations is employed for the simulations. Numerical results are enhanced by the introduction of an anisotropic remeshing strategy. The numerical procedure is validated by comparing the predictions of the model with experimental results. PMID:16298846

  11. Studies of Multipactor in Dielectric-Loaded Accelerator Structures: Comparison of Simulation Results with Experimental Data

    SciTech Connect

    Sinitsyn, Oleksandr; Nusinovich, Gregory; Antonsen, Thomas Jr.

    2010-11-04

    In this paper new results of numerical studies of multipactor in dielectric-loaded accelerator structures are presented. The results are compared with experimental data obtained during recent studies of such structures performed by Argonne National Laboratory, the Naval Research Laboratory, SLAC National Accelerator Laboratory and Euclid TechLabs, LLC. Good agreement between the theory and experiment was observed for the structures with larger inner diameter, however the structures with smaller inner diameter demonstrated a discrepancy between the two. Possible reasons for such discrepancy are discussed.

  12. Direct Identification of Elastic Constants of Anisotropic Plates by Modal Analysis: Experimental Results

    NASA Astrophysics Data System (ADS)

    Grédiac, M.; Fournier, N.; Paris, P.-A.; Surrel, Y.

    1998-03-01

    The determination of the six elastic stiffnesses of thin anisotropic plates from vibration tests is usually performed with numerical procedures based on the finite element or the Rayleigh-Ritz method, which both require assumptions concerning the studied mode shapes. The present paper describes a method based on the measurement and the processing of natural frequencies as well as mode shapes of the vibrating tested plate. As a result, the unknown stiffnesses are determined directly, without any iterative calculations. The experimental aspects of the method are presently described and several results illustrate the relevance of the approach.

  13. Some experimental results on Coanda effect with application to a flying vehicle

    NASA Astrophysics Data System (ADS)

    Crivoi, O.; Doroftei, I.

    2016-08-01

    In this paper some experimental results related to the Coanda effect are presented. The idea is to use them to build and control a flying vehicle. Our experiments have been done on an laboratory testing device. From the first obtained results we have seen some advantages and disadvantages to applying Coanda effect to a flying vehicle. The advantages are: reducing the pressure near the of the convex surface, protected screw, vertical takeoff and landing. The main disadvantage is the cost of the fuselage and the extra weight that he has. Our conclusion at this time is that this technical solution can bring some benefits through a suited sizing and geometry with vehicle mass.

  14. Preliminary results of the large experimental wind turbine phase of the national wind energy program

    NASA Technical Reports Server (NTRS)

    Thomas, R. L.; Sholes, T.; Sholes, J. E.

    1975-01-01

    The preliminary results of two projects in the development phase of reliable wind turbines designed to supply cost-competitive electrical energy were discussed. An experimental 100 kW wind turbine design and its status are first reviewed. The results of two parallel design studies for determining the configurations and power levels for wind turbines with minimum energy costs are also discussed. These studies predict wind energy costs of 1.5 to 7 cents per kW-h for wind turbines produced in quantities of 100 to 1000 per year and located at sites having average winds of 12 to 18 mph.

  15. Wind Code Application to External Forebody Flowfields with Comparisons to Experimental Results

    NASA Technical Reports Server (NTRS)

    Frate, F. C.; Kim, H. D.

    2001-01-01

    The WIND Code, a general purpose Navier-Stokes solver, has been utilized to obtain supersonic external flowfield Computational Fluid Dynamics (CFD) solutions over an axisymmetric, parabolic forebody with comparisons made to wind tunnel experimental results. Various cases have been investigated at supersonic freestream conditions ranging from Mach 2.0 to 3.5, at 0 deg and 3 deg angles-of-attack, and with either a sharp-nose or blunt-nose forebody configuration. Both a turbulent (Baldwin-Lomax algebraic turbulence model) and a laminar model have been implemented in the CFD. Obtaining the solutions involved utilizing either the parabolized- or full-Navier-Stokes analyses supplied in WIND. Comparisons have been made with static pressure measurements, with boundary-layer rake and flowfield rake pitot pressure measurements, and with temperature sensitive paint experimental results. Using WIND's parabolized Navier-Stokes capability, grid sequencing, and the Baldwin-Lomax algebraic turbulence model allowed for significant reductions in computational time while still providing good agreement with experiment. Given that CFD and experiment compare well, WIND is found to be a good computational platform for solving this type of forebody problem, and the grids developed in conjunction with it will be used in the future to investigate varying freestream conditions not tested experimentally.

  16. Experimental laser anastomosis of the large bowel: conclusive results and future prospect

    NASA Astrophysics Data System (ADS)

    Kawahara, Masaki; Kuramoto, Shu; Ryan, Peter

    2003-06-01

    Completely sutureless end-to-end large bowel anastomoses were successfully performed in New Zealand white rabbits by using 1064 nm, 0.4-W power pulsating Nd:YAG laser to produce welding. Purpose: The aim of this study was to assess the results of our whole experimental data and summarize our experimental work on laser colon anastomosis. Methods: This experimental study investigated integrity of anastomosis, degree of narrowing, macroscopic appearance, microscopic findings, animal body weight change, and collagen concentration of laser colon anastomoses, compared with those of conventional sutured anastomoses up to ninety postoperative days. Results: Bursting pressures of laser anastomoses were at first low and came to be equivalent at seven days, but the laser group exhibited a consistent narrowing tendency. However, laser anastomoses demonstrated fewer and milder adhesions, and animals showed a better recovery of body weight. Histologically, laser anastomoses showed better layer-to-layer reconstitution without foreign body response and with less fibrosis. Difference in collagen concentration did not reach statistical significance. Conclusion: The technique of laser anastomosis presents a promising alternative to suturing in reconstitution of the large bowel.

  17. Respiratory rate detection algorithm based on RGB-D camera: theoretical background and experimental results

    PubMed Central

    Freddi, Alessandro; Monteriù, Andrea; Longhi, Sauro

    2014-01-01

    Both the theoretical background and the experimental results of an algorithm developed to perform human respiratory rate measurements without any physical contact are presented. Based on depth image sensing techniques, the respiratory rate is derived by measuring morphological changes of the chest wall. The algorithm identifies the human chest, computes its distance from the camera and compares this value with the instantaneous distance, discerning if it is due to the respiratory act or due to a limited movement of the person being monitored. To experimentally validate the proposed algorithm, the respiratory rate measurements coming from a spirometer were taken as a benchmark and compared with those estimated by the algorithm. Five tests were performed, with five different persons sat in front of the camera. The first test aimed to choose the suitable sampling frequency. The second test was conducted to compare the performances of the proposed system with respect to the gold standard in ideal conditions of light, orientation and clothing. The third, fourth and fifth tests evaluated the algorithm performances under different operating conditions. The experimental results showed that the system can correctly measure the respiratory rate, and it is a viable alternative to monitor the respiratory activity of a person without using invasive sensors. PMID:26609383

  18. Comparison of numerical and experimental results of the flow in the U9 Kaplan turbine model

    NASA Astrophysics Data System (ADS)

    Petit, O.; Mulu, B.; Nilsson, H.; Cervantes, M.

    2010-08-01

    The present work compares simulations made using the OpenFOAM CFD code with experimental measurements of the flow in the U9 Kaplan turbine model. Comparisons of the velocity profiles in the spiral casing and in the draft tube are presented. The U9 Kaplan turbine prototype located in Porjus and its model, located in Älvkarleby, Sweden, have curved inlet pipes that lead the flow to the spiral casing. Nowadays, this curved pipe and its effect on the flow in the turbine is not taken into account when numerical simulations are performed at design stage. To study the impact of the inlet pipe curvature on the flow in the turbine, and to get a better overview of the flow of the whole system, measurements were made on the 1:3.1 model of the U9 turbine. Previously published measurements were taken at the inlet of the spiral casing and just before the guide vanes, using the laser Doppler anemometry (LDA) technique. In the draft tube, a number of velocity profiles were measured using the LDA techniques. The present work extends the experimental investigation with a horizontal section at the inlet of the draft tube. The experimental results are used to specify the inlet boundary condition for the numerical simulations in the draft tube, and to validate the computational results in both the spiral casing and the draft tube. The numerical simulations were realized using the standard k-e model and a block-structured hexahedral wall function mesh.

  19. Comparison of simulations and experimental results from ICF implosions using capsules of varying surface roughness.

    NASA Astrophysics Data System (ADS)

    Turner, R. E.; Glebov, V.

    2005-10-01

    We have conducted a series of indirect-drive ICF implosion experiments at Omega, using capsules with deliberately roughened surfaces. The 10 atm DD fill capsules had a convergence ratio of 18, higher than previous Nova experiments [M. Marinak et al, Phys. Plasmas 3, 2070 (1996)]; the pre-heat shielded, Ge-doped CH ablators had moderately high (˜200) Raleigh-Taylor growth factors. Each capsule's surface quality was measured using atomic force microscopy. Gated x-ray imaging of the imploded core was used to assure that basic symmetry was maintained, while `best-surface' capsules were used as controls with every experimental run. Neutron yields were observed to decrease as surface roughness increased. Integrated simulations, including mix modeling, have been performed, and are compared to the experimental results. This work was performed under the auspices of the U.S. Department of Energy by the University of California, Lawrence Livermore National Laboratory under contract No. W-7405-Eng-48.

  20. Shuttle Return To Flight Experimental Results: Protuberance Effects on Boundary Layer Transition

    NASA Technical Reports Server (NTRS)

    Liechty, Derek S.; Berry, Scott A.; Horvath, Thomas J.

    2006-01-01

    The effect of isolated roughness elements on the windward boundary layer of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamic Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental effort was initiated to provide a roughness effects database for developing transition criteria to support on-orbit decisions to repair damage to the thermal protection system. Boundary layer transition results were obtained using trips of varying heights and locations along the centerline and attachment lines of 0.0075-scale models. Global heat transfer images using phosphor thermography of the Orbiter windward surface and the corresponding heating distributions were used to infer the state of the boundary layer (laminar, transitional, or turbulent). The database contained within this report will be used to formulate protuberance-induced transition correlations using predicted boundary layer edge parameters.

  1. Stimulating Contributions to Public Goods through Information Feedback: Some Experimental Results.

    PubMed

    Janssen, Marco A; Lee, Allen; Sundaram, Hari

    2016-01-01

    In traditional public good experiments participants receive an endowment from the experimenter that can be invested in a public good or kept in a private account. In this paper we present an experimental environment where participants can invest time during five days to contribute to a public good. Participants can make contributions to a linear public good by logging into a web application and performing virtual actions. We compared four treatments, with different group sizes and information of (relative) performance of other groups. We find that information feedback about performance of other groups has a small positive effect if we control for various attributes of the groups. Moreover, we find a significant effect of the contributions of others in the group in the previous day on the number of points earned in the current day. Our results confirm that people participate more when participants in their group participate more, and are influenced by information about the relative performance of other groups.

  2. LBE water interaction in sub-critical reactors: First experimental and modelling results

    NASA Astrophysics Data System (ADS)

    Ciampichetti, A.; Agostini, P.; Benamati, G.; Bandini, G.; Pellini, D.; Forgione, N.; Oriolo, F.; Ambrosini, W.

    2008-06-01

    This paper concerns the study of the phenomena involved in the interaction between LBE and pressurised water which could occur in some hypothetical accidents in accelerator driven system type reactors. The LIFUS 5 facility was designed and built at ENEA-Brasimone to reproduce this kind of interaction in a wide range of conditions. The first test of the experimental program was carried out injecting water at 70 bar and 235 °C in a reaction vessel containing LBE at 1 bar and 350 °C. A pressurisation up to 80 bar was observed in the test section during the considered transient. The SIMMER III code was used to simulate the performed test. The calculated data agree in a satisfactory way with the experimental results giving confidence in the possibility to use this code for safety analyses of heavy liquid metal cooled reactors.

  3. Stimulating Contributions to Public Goods through Information Feedback: Some Experimental Results.

    PubMed

    Janssen, Marco A; Lee, Allen; Sundaram, Hari

    2016-01-01

    In traditional public good experiments participants receive an endowment from the experimenter that can be invested in a public good or kept in a private account. In this paper we present an experimental environment where participants can invest time during five days to contribute to a public good. Participants can make contributions to a linear public good by logging into a web application and performing virtual actions. We compared four treatments, with different group sizes and information of (relative) performance of other groups. We find that information feedback about performance of other groups has a small positive effect if we control for various attributes of the groups. Moreover, we find a significant effect of the contributions of others in the group in the previous day on the number of points earned in the current day. Our results confirm that people participate more when participants in their group participate more, and are influenced by information about the relative performance of other groups. PMID:27459070

  4. Artificial cochlea and acoustic black hole travelling waves observation: Model and experimental results

    NASA Astrophysics Data System (ADS)

    Foucaud, Simon; Michon, Guilhem; Gourinat, Yves; Pelat, Adrien; Gautier, François

    2014-07-01

    An inhomogeneous fluid structure waveguide reproducing passive behaviour of the inner ear is modelled with the help of the Wentzel-Kramers-Brillouin method. A physical setup is designed and built. Experimental results are compared with a good correlation to theoretical ones. The experimental setup is a varying width plate immersed in fluid and terminated with an acoustic black hole. The varying width plate provides a spatial repartition of the vibration depending on the excitation frequency. The acoustic black hole is made by decreasing the plate's thickness with a quadratic profile and by covering this region with a thin film of viscoelastic material. Such a termination attenuates the flexural wave reflection at the end of the waveguide, turning standing waves into travelling waves.

  5. Stimulating Contributions to Public Goods through Information Feedback: Some Experimental Results

    PubMed Central

    Janssen, Marco A.; Lee, Allen; Sundaram, Hari

    2016-01-01

    In traditional public good experiments participants receive an endowment from the experimenter that can be invested in a public good or kept in a private account. In this paper we present an experimental environment where participants can invest time during five days to contribute to a public good. Participants can make contributions to a linear public good by logging into a web application and performing virtual actions. We compared four treatments, with different group sizes and information of (relative) performance of other groups. We find that information feedback about performance of other groups has a small positive effect if we control for various attributes of the groups. Moreover, we find a significant effect of the contributions of others in the group in the previous day on the number of points earned in the current day. Our results confirm that people participate more when participants in their group participate more, and are influenced by information about the relative performance of other groups. PMID:27459070

  6. Radio propagation at 900 MHz in urban areas: Models with a fixed frequency and experimental results

    NASA Astrophysics Data System (ADS)

    Olivier, P.; Tiffon, J.

    1984-09-01

    Models which describe multipath propagation are examined in order to design a 900 MHz mobile communication system adapted to urban areas. A justification of the experimental data treatment is derived from this analysis. The measurements were made at a fixed 855 MHz frequency, transmitting from three locations. The fast fluctuations of the received signals are well represented by a Rayleigh process, which means that there are practically no paths of direct transmission. The coherence length is 1 m. The statistical distribution of the average field is Gaussian and the normal deviation decreases with the distance emitter-receiver. The empiric Okumura-Hata prediction model agrees well with the experimental results, giving an average cell field decreasing with distance with a logarithmic law.

  7. Circular Samples as Objects for Magnetic Resonance Imaging - Mathematical Simulation, Experimental Results

    NASA Astrophysics Data System (ADS)

    Frollo, Ivan; Krafčík, Andrej; Andris, Peter; Přibil, Jiří; Dermek, Tomáš

    2015-12-01

    Circular samples are the frequent objects of "in-vitro" investigation using imaging method based on magnetic resonance principles. The goal of our investigation is imaging of thin planar layers without using the slide selection procedure, thus only 2D imaging or imaging of selected layers of samples in circular vessels, eppendorf tubes,.. compulsorily using procedure "slide selection". In spite of that the standard imaging methods was used, some specificity arise when mathematical modeling of these procedure is introduced. In the paper several mathematical models were presented that were compared with real experimental results. Circular magnetic samples were placed into the homogenous magnetic field of a low field imager based on nuclear magnetic resonance. For experimental verification an MRI 0.178 Tesla ESAOTE Opera imager was used.

  8. Design and Experimental Results for the S827 Airfoil; Period of Performance: 1998--1999

    SciTech Connect

    Somers, D. M.

    2005-01-01

    A 21%-thick, natural-laminar-flow airfoil, the S827, for the 75% blade radial station of 40- to 50-meter, stall-regulated, horizontal-axis wind turbines has been designed and analyzed theoretically and verified experimentally in the NASA Langley Low-Turbulence Pressure Tunnel. The primary objective of restrained maximum lift has not been achieved, although the maximum lift is relatively insensitive to roughness, which meets the design goal. The airfoil exhibits a relatively docile stall, which meets the design goal. The primary objective of low profile drag has been achieved. The constraints on the pitching moment and the airfoil thickness have been satisfied. Comparisons of the theoretical and experimental results generally show good agreement with the exception of maximum lift, which is significantly underpredicted.

  9. Design and Experimental Results for the S825 Airfoil; Period of Performance: 1998-1999

    SciTech Connect

    Somers, D. M.

    2005-01-01

    A 17%-thick, natural-laminar-flow airfoil, the S825, for the 75% blade radial station of 20- to 40-meter, variable-speed and variable-pitch (toward feather), horizontal-axis wind turbines has been designed and analyzed theoretically and verified experimentally in the NASA Langley Low-Turbulence Pressure Tunnel. The two primary objectives of high maximum lift, relatively insensitive to roughness and low-profile drag have been achieved. The airfoil exhibits a rapid, trailing-edge stall, which does not meet the design goal of a docile stall. The constraints on the pitching moment and the airfoil thickness have been satisfied. Comparisons of the theoretical and experimental results generally show good agreement.

  10. New experimental results on cosmic gravitational effects and the centenary of Einstein's equation

    NASA Astrophysics Data System (ADS)

    Unnikrishnan, C. S.

    As one celebrates the centennial triumph of the general theory of relativity (GTR), Einstein's theory of gravity, it is appropriate to review and assess the experimental foundations of the theory in the context of what we know about matter in the universe, a knowledge that did not exist when GTR was formulated. A worldview consistent with and rigorously based on experimental evidence indeed demands a paradigm change and theoretical revision. The new theory of dynamics and relativity is Cosmic Relativity, with both absolute space and absolute time of a preferred cosmic frame, and it implies a modified GTR on its new and deeper foundation. Supporting results from laboratory experiments on the relative one-way velocity of light and the direct gravitational action of the cosmic matter on dynamics are discussed, demanding a modified equation of relativistic gravitation, aptly called the Centenary Einstein's equation.

  11. Supersonic Retropropulsion Experimental Results from the NASA Ames 9- x 7-Foot Supersonic Wind Tunnel

    NASA Technical Reports Server (NTRS)

    Berry, Scott A.; Rhode, Matthew N.; Edquist, Karl T.

    2012-01-01

    Supersonic retropropulsion was experimentally examined in the Ames Research Center 9x7-Foot Supersonic Wind Tunnel at Mach 1.8 and 2.4. The experimental model, previously designed for and tested in the Langley Research Center Unitary Plan Wind Tunnel at Mach 2.4, 3.5 and 4.6, was a 5-in diameter 70-deg sphere-cone forebody with a 9.55-in long cylindrical aftbody. The forebody was designed to accommodate up to four 4:1 area ratio nozzles, one on the model centerline and the other three on the half radius spaced 120-deg apart. Surface pressure and flow visualization were the primary measurements, including high-speed data to investigate the dynamics of the interactions between the bow and nozzle shocks. Three blowing configurations were tested with thrust coefficients up to 10 and angles of attack up to 20-deg. Preliminary results and observations from the test are provided

  12. Use of dynamic theory to describe experimental results from volume holography

    NASA Technical Reports Server (NTRS)

    Magnusson, R.; Gaylord, T. K.

    1976-01-01

    The general applicability of dynamic theory to the description of the recording and readout characteristics of volume (thick) hologram gratings is indicated. In dynamic theory (as opposed to static theory), the volume nature of the thick holographic grating allows the interference of an incident light beam with its own diffracted beam inside the recording medium. This effect causes the continuous recording of another grating that alters the initial one, producing a resultant grating that is not uniform through the thickness of the recording material and a grating whose writing and reading characteristics may vary dramatically, depending on the recording material and the experimental conditions. A large number of diverse types of writing, reading, and angular-selectivity behavior have been reported. The dynamic theory of thick-hologram writing and reading is shown to predict qualitatively all of these various types of experimental behavior.

  13. Shuttle Return To Flight Experimental Results: Cavity Effects on Boundary Layer Transition

    NASA Technical Reports Server (NTRS)

    Liechty, Derek S.; Horvath, Thomas J.; Berry, Scott A.

    2006-01-01

    The effect of an isolated rectangular cavity on hypersonic boundary layer transition of the windward surface of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamics Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental study was initiated to provide a cavity effects database for developing hypersonic transition criteria to support on-orbit decisions to repair a damaged thermal protection system. Boundary layer transition results were obtained using 0.0075-scale Orbiter models with simulated tile damage (rectangular cavities) of varying length, width, and depth. The database contained within this report will be used to formulate cavity-induced transition correlations using predicted boundary layer edge parameters.

  14. Carbon sequestration via reaction with basaltic rocks: geochemical modeling and experimental results

    USGS Publications Warehouse

    Rosenbauer, Robert J.; Thomas, Burt; Bischoff, James L.; Palandri, James

    2012-01-01

    Basaltic rocks are potential repositories for sequestering carbon dioxide (CO2) because of their capacity for trapping CO2 in carbonate minerals. We carried out a series of thermodynamic equilibrium models and high pressure experiments, reacting basalt with CO2-charged fluids over a range of conditions from 50 to 200 °C at 300 bar. Results indicate basalt has a high reactivity to CO2 acidified brine. Carbon dioxide is taken up from solution at all temperatures from 50 to 200 °C, 300 bar, but the maximum extent and rate of reaction occurs at 100 °C, 300 bar. Reaction path simulations utilizing the geochemical modeling program CHILLER predicted an equilibrium carbonate alteration assemblage of calcite, magnesite, and siderite, but the only secondary carbonate identified in the experiments was a ferroan magnesite. The amount of uptake at 100 °C, 300 bar ranged from 8% by weight for a typical tholeite to 26% for a picrite. The actual amount of CO2 uptake and extent of rock alteration coincides directly with the magnesium content of the rock suggesting that overall reaction extent is controlled by bulk basalt Mg content. In terms of sequestering CO2, an average basaltic MgO content of 8% is equivalent to 2.6 × 108 metric ton CO2/km3 basalt.

  15. Inviscid Flow Field Effects: Experimental results. [optical distortions over airborne laser turrets

    NASA Technical Reports Server (NTRS)

    Otten, L. J., III; Gilbert, K. G.

    1980-01-01

    The aero-optical distortions due to invisid flow effects over airborne laser turrets is investigated. Optical path differences across laser turret apertures are estimated from two data sources. The first is a theoretical study of main flow effects for a spherical turret assembly for a Mach number (M) of 0.6. The second source is an actual wind tunnel density field measurement on a 0.3 scale laser turret/fairing assembly, with M = 0.75. A range of azimuthal angles from 0 to 90 deg was considered, while the elevation angle was always 0 deg (i.e., in the plane of the flow). The calculated optical path differences for these two markedly different geometries are of the same order. Scaling of results to sea level conditions and an aperture diameter of 50 cm indicated up to 0.0007 cm of phase variation across the aperture for certain forward look angles and a focal length of F = -11.1 km. These values are second order for a 10.6 micron system.

  16. Crystalline and Spectroscopic Experimental Study of the Dinitromesithylen (DNM) Compared with the Theoretical Results

    NASA Astrophysics Data System (ADS)

    Brihi, O.; Medjroubi, M. L.; Hamdouni, N.; Meinnel, J.; Boucekkine, A.; Boudjada, A.

    The aim by our group is to understand the behaviour of the grouping methyl starting from the study of molecules having a great symmetry. In this part of work, it is had the crystalline structure of the dinitromesitylen (DNM) who is solved starting from the diffraction of x-rays starting from a monocrystal at the ambient temperature. Parallel to the experimental study, we undertook theoretical calculations conformation of the insulated molecule of DNM by using the methods of the DFT (Density Functional Theory).Calculations of optimization of the molecular conformation of the DNM by using the chain of program GAUSSIAN03 and functional MPW1PW91, B3LYP level with the 6-311G and LANL2DZ bases gave a conformation Cs with results very close to the experiment for the lengths and the angles of bond. The computation results obtained starting from the base set (6-311G) and functional MPW1PW91 give for the conformation of Dinitromesitylen (DNM) a good agreement of about a 1.9% for the lengths of bond and 1.2% for the angles of bond compared with the results of the diffraction of x-rays. Calculations of Raman and infra-red spectroscopy undertaken starting from the results of optimization by using same functional MPW1PW91 and B3LYP and the sets of bases 6-311G LanL2DZ led to the values of frequencies very close to the experimental results.

  17. Cabauw Experimental Results from the Project for Intercomparison of Land-Surface Parameterization Schemes

    NASA Technical Reports Server (NTRS)

    Chen, Tian Hong; Henderson-Sellers, A.; Milly, P. C. D.; Pitman, A. J.; Beljaars, A. C. M.; Polcher, J.; Abramopoulos, F.; Boone, A.; Chang, S.; Chen, F.; Dai, Y.; Desborough, C. E.; Dickinson, R. E.; Duemenil, L.; Ek, M.; Garratt, J. R.; Gedney, N.; Gusev, Y. M.; Kim, J.; Koster, R.

    1997-01-01

    ). Actual runoff at the site is believed to be dominated by vertical drainage to ground water, but several schemes produced significant amounts of runoff as overland flow or interflow. There is a range across schemes of 184 mm (40% of total pore volume) in the simulated annual mean root-zone soil moisture. Unfortunately, no measurements of soil moisture were available for model evaluation. A theoretical analysis suggested that differences in boundary conditions used in various schemes are not sufficient to explain the large variance in soil moisture. However, many of the extreme values of soil moisture could be explained in terms of the particulars of experimental setup or excessive evapotranspiration.

  18. Cabauw experimental results from the Project for Intercomparison of Land-Surface Parameterization Schemes

    USGS Publications Warehouse

    Chen, T.H.; Henderson-Sellers, A.; Milly, P.C.D.; Pitman, A.J.; Beljaars, A.C.M.; Polcher, J.; Abramopoulos, F.; Boone, A.; Chang, S.; Chen, F.; Dai, Y.; Desborough, C.E.; Dickinson, R.E.; Dumenil, L.; Ek, M.; Garratt, J.R.; Gedney, N.; Gusev, Y.M.; Kim, J.; Koster, R.; Kowalczyk, E.A.; Laval, K.; Lean, J.; Lettenmaier, D.; Liang, X.; Mahfouf, Jean-Francois; Mengelkamp, H.-T.; Mitchell, Ken; Nasonova, O.N.; Noilhan, J.; Robock, A.; Rosenzweig, C.; Schaake, J.; Schlosser, C.A.; Schulz, J.-P.; Shao, Y.; Shmakin, A.B.; Verseghy, D.L.; Wetzel, P.; Wood, E.F.; Xue, Y.; Yang, Z.-L.; Zeng, Q.

    1997-01-01

    ). Actual runoff at the site is believed to be dominated by vertical drainage to groundwater, but several schemes produced significant amounts of runoff as overland flow or interflow. There is a range across schemes of 184 mm (40% of total pore volume) in the simulated annual mean root-zone soil moisture. Unfortunately, no measurements of soil moisture were available for model evaluation. A theoretical analysis suggested that differences in boundary conditions used in various schemes are not sufficient to explain the large variance in soil moisture. However, many of the extreme values of soil moisture could be explained in terms of the particulars of experimental setup or excessive evapotranspiration.

  19. OPERA, MINOS Experimental Result Prove Special and General Relativity Theories; the Principle of Lorentz Invariance Invalid

    NASA Astrophysics Data System (ADS)

    Pressler, David E.

    2012-03-01

    A great discrepancy exists - the speed of light and the neutrino speed must be identical; as indicated by supernova1987A; yet, OPERA predicts faster-than-light neutrinos. Einstein's theories are based on the invariance of the speed of light, and no privileged Galilean frame of reference exists. Both of these hypotheses are in error and must be reconciled in order to solve the dilemma. The Michelson-Morley Experiment was misinterpreted - my Neoclassical Theory postulates that BOTH mirrors of the interferometer physically and absolutely move towards its center. The result is a three-directional-Contraction, (x, y, z axis), an actual distortion of space itself; a C-Space condition. ``PRESSLER'S LAW OF C-SPACE: The speed of light, c, will always be measured the same speed in all three directions (˜300,000 km/sec), in ones own inertial reference system, and will always be measured as having a different speed in all other inertial frames which are at a different kinetic energy level or at a location with a different strength gravity field'' Thus, the faster you go, motion, or the stronger the gravity field the smaller you get in all three directions. OPERA results are explained; at the surface of Earth, the strength of gravity field is at maximum -- below the earth's surface, time and space is less distorted; therefore, time is absolutely faster accordingly. Reference OPERA's preprint: Neutrino's faster time-effect due to altitude difference; (10-13ns) x c (299792458m) = 2.9 x 10-5 m/ns x distance (730085m) + 21.8m.) This is consistent with the OPERA result.

  20. Free space optical communication flight mission: simulations and experimental results on ground level demonstrator

    NASA Astrophysics Data System (ADS)

    Mata Calvo, Ramon; Ferrero, Valter; Camatel, Stefano; Catalano, Valeria; Bonino, Luciana; Toselli, Italo

    2009-05-01

    In the context of the increasing demand in high-speed data link for scientific, planetary exploration and earth observation missions, the Italian Space Agency (ASI), involving Thales Alenia Space as prime, the Polytechnic of Turin and other Italian partners, is developing a program for feasibility demonstration of optical communication system with the goal of a prototype flight mission in the next future. We have designed and analyzed a ground level bidirectional Free Space Optical Communication (FSOC) Breadboard at 2.5Gbit/s working at 1550nm as an emulator of slant path link. The breadboard is full-working and we tested it back-toback, at 500m and 2.3km during one month. The distances were chosen in order to get an equivalent slant path cumulative turbulence in a ground level link. The measurements campaign was done during the day and the night time and under several weather conditions, from sunny, rainy or windy. So we could work under very different turbulence conditions from weak to strong turbulence. We measured the scintillation both, on-axis and off-axis by introducing known misalignments at the terminals, transmission losses at both path lengths and BER at both receivers. We present simulations results considering slant and ground level links, where we took into account the atmospheric effects; scintillation, beam spread, beam wander and fade probability, and comparing them with the ground level experimental results, we find a good agreement between them. Finally we discuss the results obtained in the experimentation and in the flight mission simulations in order to apply our experimental results in the next project phases.

  1. Retained gas sampler extractor mixing and mass transfer rate study: Experimental and simulation results

    SciTech Connect

    Recknagle, K.P.; Bates, J.M.; Shekarriz, A.

    1997-11-01

    Research staff at Pacific Northwest National Laboratory conducted experimental testing and computer simulations of the impeller-stirred Retained Gas Sampler (RGS) gas extractor system. This work was performed to verify experimentally the effectiveness of the extractor at mixing viscous fluids of both Newtonian and non-Newtonian rheology representative of Hanford single- and double-shell wastes, respectively. Developing the computational models and validating their results by comparing them with experimental results would enable simulations of the mixing process for a range of fluid properties and mixing speeds. Five tests were performed with a full-scale, optically transparent model extractor to provide the data needed to compare mixing times for fluid rheology, mixer rotational direction, and mixing speed variation. The computer model was developed and exercised to simulate the tests. The tests demonstrated that rotational direction of the pitched impeller blades was not as important as fluid rheology in determining mixing time. The Newtonian fluid required at least six hours to mix at the hot cell operating speed of 3 rpm, and the non-Newtonian fluid required at least 46 hours at 3 rpm to become significantly mixed. In the non-Newtonian fluid tests, stagnant regions within the fluid sometimes required days to be fully mixed. Higher-speed (30 rpm) testing showed that the laminar mixing time was correlated to mixing speed. The tests demonstrated that, using the RGS extractor and current procedures, complete mixing of the waste samples in the hot cell should not be expected. The computer simulation of Newtonian fluid mixing gave results comparable to the test while simulation of non-Newtonian fluid mixing would require further development. In light of the laboratory test results, detailed parametric analysis of the mixing process was not performed.

  2. Photovoltaic Grid-Connected Modeling and Characterization Based on Experimental Results

    PubMed Central

    Humada, Ali M.; Hojabri, Mojgan; Sulaiman, Mohd Herwan Bin; Hamada, Hussein M.; Ahmed, Mushtaq N.

    2016-01-01

    A grid-connected photovoltaic (PV) system operates under fluctuated weather condition has been modeled and characterized based on specific test bed. A mathematical model of a small-scale PV system has been developed mainly for residential usage, and the potential results have been simulated. The proposed PV model based on three PV parameters, which are the photocurrent, IL, the reverse diode saturation current, Io, the ideality factor of diode, n. Accuracy of the proposed model and its parameters evaluated based on different benchmarks. The results showed that the proposed model fitting the experimental results with high accuracy compare to the other models, as well as the I-V characteristic curve. The results of this study can be considered valuable in terms of the installation of a grid-connected PV system in fluctuated climatic conditions. PMID:27035575

  3. Photovoltaic Grid-Connected Modeling and Characterization Based on Experimental Results.

    PubMed

    Humada, Ali M; Hojabri, Mojgan; Sulaiman, Mohd Herwan Bin; Hamada, Hussein M; Ahmed, Mushtaq N

    2016-01-01

    A grid-connected photovoltaic (PV) system operates under fluctuated weather condition has been modeled and characterized based on specific test bed. A mathematical model of a small-scale PV system has been developed mainly for residential usage, and the potential results have been simulated. The proposed PV model based on three PV parameters, which are the photocurrent, IL, the reverse diode saturation current, Io, the ideality factor of diode, n. Accuracy of the proposed model and its parameters evaluated based on different benchmarks. The results showed that the proposed model fitting the experimental results with high accuracy compare to the other models, as well as the I-V characteristic curve. The results of this study can be considered valuable in terms of the installation of a grid-connected PV system in fluctuated climatic conditions. PMID:27035575

  4. Comparison between experimental and analytical results for seesaw energy dissipation systems using fluid viscous dampers

    NASA Astrophysics Data System (ADS)

    Kang, Jae-Do; Tagawa, Hiroshi

    2016-03-01

    This paper presents results of experimental and numerical investigations of a seesaw energy dissipation system (SEDS) using fluid viscous dampers (FVDs). To confirm the characteristics of the FVDs used in the tests, harmonic dynamic loading tests were conducted in advance of the free vibration tests and the shaking table tests. Shaking table tests were conducted to demonstrate the damping capacity of the SEDS under random excitations such as seismic waves, and the results showed SEDSs have sufficient damping capacity for reducing the seismic response of frames. Free vibration tests were conducted to confirm the reliability of simplified analysis. Time history response analyses were also conducted and the results are in close agreement with shaking table test results.

  5. Transdermal flux predictions for selected selective oestrogen receptor modulators (SERMs): comparison with experimental results.

    PubMed

    Güngör, Sevgi; Delgado-Charro, M Begoña; Masini-Etévé, Valérie; Potts, Russell O; Guy, Richard H

    2013-12-28

    The aim of this work was to evaluate the feasibility of delivering transdermally a series of highly lipophilic compounds (log P ~4-7), comprising several selective oestrogen receptor modulators and a modified testosterone (danazol). The maximum fluxes of the drugs were predicted theoretically using the modified Potts & Guy algorithm (to determine the permeability coefficient (kp) from water) and the calculated aqueous solubilities. The correction provided by Cleek & Bunge took into account the contribution of the viable epidermal barrier to the skin permeation of highly lipophilic compounds. Experimental measurements of drug fluxes from saturated hydroalcoholic solutions were determined in vitro through excised pig skin. Overall, the predicted fluxes were in good general agreement (within a factor of 10) with the experimental results. Most of the experimental fluxes were greater than those predicted theoretically suggesting that the 70:30 v/v ethanol-water vehicle employed may have had a modest skin penetration enhancement effect. This investigation shows that the transdermal fluxes of highly lipophilic compounds can be reasonably predicted from first principles provided that the viable epidermis, underlying the stratum corneum, is included as a potentially important contributor to the skin's overall barrier function. Furthermore, the absolute values of the measured fluxes, when considered in parallel with previous clinical studies, indicate that it might be feasible to topically deliver a therapeutically useful amount of some of the compounds considered to treat cancerous breast tissue. PMID:24076520

  6. Supersonic Retropropulsion Experimental Results from the NASA Langley Unitary Plan Wind Tunnel

    NASA Technical Reports Server (NTRS)

    Berry, Scott A.; Rhode, Matthew N.; Edquist, Karl T.; Player, Charles J.

    2011-01-01

    A new supersonic retropropulsion experimental effort, intended to provide code validation data, was recently completed in the Langley Research Center Unitary Plan Wind Tunnel Test Section 2 over the Mach number range from 2.4 to 4.6. The experimental model was designed using insights gained from pre-test computations, which were instrumental for sizing and refining the model to minimize tunnel wall interference and internal flow separation concerns. A 5-in diameter 70-deg sphere-cone forebody with a roughly 10-in long cylindrical aftbody was the baseline configuration selected for this study. The forebody was designed to accommodate up to four 4:1 area ratio supersonic nozzles. Primary measurements for this model were a large number of surface pressures on the forebody and aftbody. Supplemental data included high-speed Schlieren video and internal pressures and temperatures. The run matrix was developed to allow for the quantification of various sources of experimental uncertainty, such as random errors due to run-to-run variations and bias errors due to flow field or model misalignments. Preliminary results and observations from the test are presented, while detailed data and uncertainty analyses are ongoing.

  7. Recovery of yttrium from cathode ray tubes and lamps' fluorescent powders: experimental results and economic simulation.

    PubMed

    Innocenzi, V; De Michelis, I; Ferella, F; Vegliò, F

    2013-11-01

    In this paper, yttrium recovery from fluorescent powder of lamps and cathode ray tubes (CRTs) is described. The process for treating these materials includes the following: (a) acid leaching, (b) purification of the leach liquors using sodium hydroxide and sodium sulfide, (c) precipitation of yttrium using oxalic acid, and (d) calcinations of oxalates for production of yttrium oxides. Experimental results have shown that process conditions necessary to purify the solutions and recover yttrium strongly depend on composition of the leach liquor, in other words, whether the powder comes from treatment of CRTs or lamp. In the optimal experimental conditions, the recoveries of yttrium oxide are about 95%, 55%, and 65% for CRT, lamps, and CRT/lamp mixture (called MIX) powders, respectively. The lower yields obtained during treatments of MIX and lamp powders are probably due to the co-precipitation of yttrium together with other metals contained in the lamps powder only. Yttrium loss can be reduced to minimum changing the experimental conditions with respect to the case of the CRT process. In any case, the purity of final products from CRT, lamps, and MIX is greater than 95%. Moreover, the possibility to treat simultaneously both CRT and lamp powders is very important and interesting from an industrial point of view since it could be possible to run a single plant treating fluorescent powder coming from two different electronic wastes.

  8. Experimental results of the investigation of a laboratory cold seal TEC

    SciTech Connect

    Yarygin, V.I.; Mironov, V.S.; Kiryushenko, A.I.; Mikheyev, A.S.; Tulin, S.M.; Meleta, Y.A.; Yarygin, D.V.; Wolff, L.R.

    1998-07-01

    The results of experimental investigation of characteristics of a laboratory Cold Seal Thermionic Energy Converter (CS TEC) with a built-in gas regulated heat pipe are discussed. They were obtained to justify the electric-thermal-physical characteristics of a flame heated CS TEC. The CS TEC design is being developed by a joint Russian-Dutch team of researchers with support of the Netherlands Organization for Scientific Research (NWO). The concept of this flame heated Cold Seal TEC was presented in a previous publication. This paper deals with experimental data on the emission properties of electrodes and the voltage-current characteristics (JVC) of an electrically heated laboratory TEC. They were studied over a wide interval of variation in the electrode temperature and interelectrode distance. The cesium vapour working pressure in the interelectrode space was regulated both by the conventional method (using a cesium reservoir) and by means of a gas regulated cesium heat pipe. This allows one to use a rubber (viton) seal in the non-condensing gas (argon) area. The acquired experimental characteristics will allow one to identify the inner parameters at further stages of their work when testing the full-scale flame heated CS TEC.

  9. Transdermal flux predictions for selected selective oestrogen receptor modulators (SERMs): comparison with experimental results.

    PubMed

    Güngör, Sevgi; Delgado-Charro, M Begoña; Masini-Etévé, Valérie; Potts, Russell O; Guy, Richard H

    2013-12-28

    The aim of this work was to evaluate the feasibility of delivering transdermally a series of highly lipophilic compounds (log P ~4-7), comprising several selective oestrogen receptor modulators and a modified testosterone (danazol). The maximum fluxes of the drugs were predicted theoretically using the modified Potts & Guy algorithm (to determine the permeability coefficient (kp) from water) and the calculated aqueous solubilities. The correction provided by Cleek & Bunge took into account the contribution of the viable epidermal barrier to the skin permeation of highly lipophilic compounds. Experimental measurements of drug fluxes from saturated hydroalcoholic solutions were determined in vitro through excised pig skin. Overall, the predicted fluxes were in good general agreement (within a factor of 10) with the experimental results. Most of the experimental fluxes were greater than those predicted theoretically suggesting that the 70:30 v/v ethanol-water vehicle employed may have had a modest skin penetration enhancement effect. This investigation shows that the transdermal fluxes of highly lipophilic compounds can be reasonably predicted from first principles provided that the viable epidermis, underlying the stratum corneum, is included as a potentially important contributor to the skin's overall barrier function. Furthermore, the absolute values of the measured fluxes, when considered in parallel with previous clinical studies, indicate that it might be feasible to topically deliver a therapeutically useful amount of some of the compounds considered to treat cancerous breast tissue.

  10. Comparison of Computational and Experimental Microphone Array Results for an 18%-Scale Aircraft Model

    NASA Technical Reports Server (NTRS)

    Lockard, David P.; Humphreys, William M.; Khorrami, Mehdi R.; Fares, Ehab; Casalino, Damiano; Ravetta, Patricio A.

    2015-01-01

    An 18%-scale, semi-span model is used as a platform for examining the efficacy of microphone array processing using synthetic data from numerical simulations. Two hybrid RANS/LES codes coupled with Ffowcs Williams-Hawkings solvers are used to calculate 97 microphone signals at the locations of an array employed in the NASA LaRC 14x22 tunnel. Conventional, DAMAS, and CLEAN-SC array processing is applied in an identical fashion to the experimental and computational results for three different configurations involving deploying and retracting the main landing gear and a part span flap. Despite the short time records of the numerical signals, the beamform maps are able to isolate the noise sources, and the appearance of the DAMAS synthetic array maps is generally better than those from the experimental data. The experimental CLEAN-SC maps are similar in quality to those from the simulations indicating that CLEAN-SC may have less sensitivity to background noise. The spectrum obtained from DAMAS processing of synthetic array data is nearly identical to the spectrum of the center microphone of the array, indicating that for this problem array processing of synthetic data does not improve spectral comparisons with experiment. However, the beamform maps do provide an additional means of comparison that can reveal differences that cannot be ascertained from spectra alone.

  11. Effectiveness of simultaneous independent realizations at low carrier-to-noise ratio to improve heterodyne Doppler lidar performance. I. Experimental results.

    PubMed

    Guérit, Gaspard; Drobinski, Philippe; Augère, Béatrice; Flamant, Pierre H

    2002-12-20

    A 1.55-microm continuous-wave heterodyne Doppler lidar (HDL) with three receiver-detector units is used to validate experimentally the findings presented in the Guérit et al. companion paper [Appl. Opt. 41, 2232 (2002)] on the effectiveness of independent realizations to improve HDL performance (velocity or power estimates or both) at a low carrier-to-noise ratio (CNR). In fact, noise has a detrimental effect on the accumulation techniques, so in the Guérit et al. companion paper, the chances of getting "heavy" speckles in HDL signal from many receiver-detector units on a single- or several-shot basis are investigated theoretically and numerically with the Zrnic HDL model. The experimental results enable us to conclude there is a very good agreement (better than 95%) between the performance computed from actual HDL data and from the theoretical prediction.

  12. Universe Clinopyroxene barometer -recalibrations on the results of the orthopyroxene thermobarometry and experimental results and applications to the clinopyroxene geotherms

    NASA Astrophysics Data System (ADS)

    Ashchepkov, I. V.

    2009-04-01

    The internal exchange of Jd-Di components on clinopyroxene allow to calibrate the universal clinopyroxene thermobarometer (Ashchepkov, 2001; 2002; 2003) based on experimental data for different systems including peridotitic, eclogitic and igneous which are represented by the augite cumulates as well as salites from the basic granulates from low crust. The equation to the peridotitic system was calibrated on the results of the othopyroxene thermobarometry (Brey. Kohler,1990- McGregor,1974). Modifications allow receiving the better agreement with the orthopyroxene estimates and results of polymineral thermobarometry (Brey, Kohler, 1990) as well as the clinopyroxene thermobarometry (Nimis, Taylor, 2000). The following equation allows working with the peridotite of the mantle lithosphere beneath cratons (30-80) kbar. P(Ash2009)=0.32 (1-0.2*Na/Al+0.012*Fe/Na)*Kd^(3/4)*ToK/(1+Fe)-35*ln(1273/ToK)*(Al+Ti+2.5Na+1.5Fe3+)+(0.9-CaO)*10+Na20/Al2O3*ToK /200 with the second iteration P=(0.0000002* P4 +0.000002+P^3-0.0027*P^2+1.2241*P) Checking of the HP experiments (Brey et al 2008, Walter, 1998; Falloon, Green, 1989; Dasgupta et al., 2007 etc.) it show the precision close to those of the best barometers (McGregor, 1974) ~5-7 but much more wider compositional range including metasomatic associations and The equation for the Al - rich assemblages allow to obtain the pressure estimates fro the megacrystalls and Al - rich peridotitic clinopyroxenes from the mantle xenoliths carried by alkaline basalts: P(Ash2009)=0.035*Kd*ToK(1+2.44Fe)-50.2 ln(1273/ToK) (Al+Ti+Na) Together with the clinopyroxene thermometer (Nimis, Taylor, 2000) it produces the TP estimates very close to those obtained with (Brey, Kohler, 1990) and values of experiments for the melting of basalts. The meagacrystalls show the polybaric origin and their range of estimated pressure corresponds well to determined for mantle peridotites and pyroxenites. The clinopyroxene geotherms for S. Africa (Boyd, Nixon, 1974

  13. Comparison of experimental data with results of some drying models for regularly shaped products

    NASA Astrophysics Data System (ADS)

    Kaya, Ahmet; Aydın, Orhan; Dincer, Ibrahim

    2010-05-01

    This paper presents an experimental and theoretical investigation of drying of moist slab, cylinder and spherical products to study dimensionless moisture content distributions and their comparisons. Experimental study includes the measurement of the moisture content distributions of slab and cylindrical carrot, slab and cylindrical pumpkin and spherical blueberry during drying at various temperatures (e.g., 30, 40, 50 and 60°C) at specific constant velocity ( U = 1 m/s) and the relative humidity φ = 30%. In theoretical analysis, two moisture transfer models are used to determine drying process parameters (e.g., drying coefficient and lag factor) and moisture transfer parameters (e.g., moisture diffusivity and moisture transfer coefficient), and to calculate the dimensionless moisture content distributions. The calculated results are then compared with the experimental moisture data. A considerably high agreement is obtained between the calculations and experimental measurements for the cases considered. The effective diffusivity values were evaluated between 0.741 × 10-5 and 5.981 × 10-5 m2/h for slab products, 0.818 × 10-5 and 6.287 × 10-5 m2/h for cylindrical products and 1.213 × 10-7 and 7.589 × 10-7 m2/h spherical products using the Model-I and 0.316 × 10-5-5.072 × 10-5 m2/h for slab products, 0.580 × 10-5-9.587 × 10-5 m2/h for cylindrical products and 1.408 × 10-7-13.913 × 10-7 m2/h spherical products using the Model-II.

  14. SWAP Modeling Results of Monitored Soil Water Moisture Data of Irrigation Experimental Study

    NASA Astrophysics Data System (ADS)

    Zeiliger, A.; Garsia-Orenes, F.; van den Elsen, E.; Mataix-Solera, J.; Semenov, V.

    2009-04-01

    In arid and semiarid zones of the Mediterranean regions a shortage of fresh water resources constitutes some time dramatic problem. In these regions with growing population and the scarce of rainfall irregularity in time during growing season an efficient use of water irrigation became a main challenge for future extensive agriculture development. In the frame of FP6 Water-Reuse project 516731 project a special field experimentation has been carried out in Alicante Region of Spain (Location UTM X: 693.809, Y: 4.279.922, Z: 626) on a Sandy Typic Xerofkuvent (Soil Survey Staff, 1999), Calcaric Fluvisol (WRB, FAO, 1989). with aim to investigate water regime in water repellent soils under irrigation of vine Vitus Labrusca. During field experimentation from 2006 till 2008 on 9 plots, there the same regime of irrigation water application was maintained, a monitoring of weather parameters was done by automatic meteorological station as well as a monitoring of soil water moisture was done by set of data-loggers and TDR-soil moisture sensors ECO-2 installed at different depts. SWAP model was used to simulate water regime of irrigated plots. Empirical coefficients of van Genuchten-Mualem's equations were calculated by pedotransfer functions derived from HYPRES data base using measured values of bulk density, organic matter content and soil texture. Testing of validity of the use of estimated curves was done by comparison with unsaturated soil hydraulic parameters of water retention and hydraulic conductivity measured in vitro by Wind's method on soil samples. Calibration of SWAP model for each plot was done on measured soil moisture data of irrigation events by adjusting a value of saturated hydraulic coefficient. Verification of the SWAP model was done by full range of experimental data. Similarity and non-similarity of the water regime at experimental plots as well as results of verification of SWAP model were analyzed

  15. Thermal Protection System Cavity Heating for Simplified and Actual Geometries Using Computational Fluid Dynamics Simulations with Unstructured Grids

    NASA Technical Reports Server (NTRS)

    McCloud, Peter L.

    2010-01-01

    Thermal Protection System (TPS) Cavity Heating is predicted using Computational Fluid Dynamics (CFD) on unstructured grids for both simplified cavities and actual cavity geometries. Validation was performed using comparisons to wind tunnel experimental results and CFD predictions using structured grids. Full-scale predictions were made for simplified and actual geometry configurations on the Space Shuttle Orbiter in a mission support timeframe.

  16. Active vibration absorber for the CSI evolutionary model - Design and experimental results. [Controls Structures Interaction

    NASA Technical Reports Server (NTRS)

    Bruner, Anne M.; Belvin, W. Keith; Horta, Lucas G.; Juang, Jer-Nan

    1991-01-01

    The development of control of large flexible structures technology must include practical demonstrations to aid in the understanding and characterization of controlled structures in space. To support this effort, a testbed facility has been developed to study practical implementation of new control technologies under realistic conditions. The paper discusses the design of a second order, acceleration feedback controller which acts as an active vibration absorber. This controller provides guaranteed stability margins for collocated sensor/actuator pairs in the absence of sensor/actuator dynamics and computational time delay. Experimental results in the presence of these factors are presented and discussed. The robustness of this design under model uncertainty is demonstrated.

  17. Experimental code verification results for reflector antenna distortion compensation by array feeds

    NASA Technical Reports Server (NTRS)

    Zaman, A. J.; Rahmat-Samii, Y.; Woo, K.

    1992-01-01

    Electronic compensation of reflector surface distortion using array feed with individual amplitude and phase control of the array elements is becoming increasingly attractive because of the recent advances in monolithic microwave integrated circuit (MMIC) technology. An algorithm has been developed previously using the concept of focal plane conjugate field matching in the receive mode and a computer code has been generated that predicts the proper excitation coefficients for the elements of the reflector feed array to compensate the effects of reflector surface distortion. This paper presents the results of an experimental study to verify the above compensation algorithm and in general to demonstrate the effectiveness of the array feed compensation technique.

  18. Voltammetry and coulometry with immersed thin layer electrodes. Part 2: Practical considerations and experimental results

    NASA Astrophysics Data System (ADS)

    Hinman, A. S.; Pons, S.; Cassidy, J.

    1984-11-01

    We have shown that geometrical considerations in the design of immersed thin layer electrochemical cells are important in the satisfactory performance of voltammetric experiments in solutions of high specific resistivity. In this paper, practical cell design and experimental results for a variety of systems are considered. In summary, we feel that reasonable care in the design of thin layer cells leads to the quantitative use of voltammetry and coulometry in systems with high specific resistivities. In the end, the effort is not much more than that required for conventional cyclic voltammetry, whereas the advantages of analysis using thin layer techniques are greater than those in conventional voltammetry.

  19. Seeded free electron laser operating with two colors: Comments on experimental results

    NASA Astrophysics Data System (ADS)

    Carpanese, M.; Ciocci, F.; Dattoli, G.; Petralia, A.; Petrillo, V.; Torre, A.

    2016-05-01

    Free electron lasers operating with two colors are promising devices for applications. The relevant modelization has provided a good understanding of the underlying physics. In this paper we present an analysis of the experimental results obtained at SPARC_LAB concerning seeded two-colors free electron laser (FEL) operation. The use of an ad hoc developed semi-analytical model based on the small-signal FEL integral equation reproduces most of the observed phenomenology. The paper discusses the reliability of the proposed method, the range of validity and its possible improvement.

  20. Experimental and computational flow-field results for an all-body hypersonic aircraft

    NASA Technical Reports Server (NTRS)

    Cleary, Joseph W.

    1989-01-01

    A comprehensive test program is defined which is being implemented in the NASA/Ames 3.5 foot Hypersonic Wind Tunnel for obtaining data on a generic all-body hypersonic vehicle for computational fluid dynamics (CFD) code validation. Computational methods (approximate inviscid methods and an upwind parabolized Navier-Stokes code) currently being applied to the all-body model are outlined. Experimental and computational results on surface pressure distributions and Pitot-pressure surveys for the basic sharp-nose model (without control surfaces) at a free-stream Mach number of 7 are presented.

  1. Experimental results on tracking performance of the MTDD Costas loop with UQPSK signal

    NASA Technical Reports Server (NTRS)

    Park, Y. H.

    1981-01-01

    The carrier tracking performance of the breadboard Costas Loop of the Multimegabit Telemetry Demodulator Detector System was tested with unbalanced quadriphase shift keying (UQPSK) signals. An S-band UQPSK modulator was built for the tests. The experimental results are very close to the theoretical rms phase error calculations. The test and analysis show that the rms phase error for UQPSK signals is less than 5 deg at the design point if the I-to-Q channel power ratio is larger than 6 dB.

  2. Development of X-ray microcalorimeters based on SOI technology and experimental results

    NASA Astrophysics Data System (ADS)

    Szeflinski, V.; Aliane, A.; De Moro, F.; Pigot, C.; Sauvageot, J.-L.; Agnèse, P.; Gasse, A.; Ribot, H.; Gremion, E.; De La Broise, X.; Navick, X. F.

    2009-10-01

    We are developing an X-ray spectro-imaging detector at cryogenic temperature (<100 mK) for next space generation missions, using silicon technology. Each pixel of this array detector is made of a tantalum absorber bonded by indium bump hybridization, to an implanted and high-temperature diffused silicon thermistor. The thermo-mechanical link, provided by the indium bump hybridization, is being improved in terms of thermal capacitance. We present the state of development and experimental results on this new generation of X-ray microcalorimeters.

  3. Recent experimental results from a long-pulse J-band relativistic klystron amplifier developmental effort

    SciTech Connect

    Kato, K.G.; Crouch, D.D.; Sar, D.R.; Speciale, R.A.; Carlsten, B.E.; Fazio, M.V.; Haynes, W.B.; Stringfield, R.M.

    1994-12-31

    Recent experimental results, supporting simulations, and design modeling are presented from a developmental effort to a produce a long pulse ({approximately}1{mu}s) J-band (5.85-8.2 GHz) relativistic klystron amplifier (RKA) of the high current NRL genealogy. This RKA is designed to operate at approximately 6.6 GHz, with a desired RF output {approximately}700 MW. Conversion of electron beam energy to microwave energy is obtained by a mock magnetically insulated coaxial converter which, in various incarnations, can be made to be either a cavity gap extractor or an inverse cathode.

  4. Impulsivity in Multiplayer Online Battle Arena Gamers: Preliminary Results on Experimental and Self-Report Measures.

    PubMed

    Nuyens, Filip; Deleuze, Jory; Maurage, Pierre; Griffiths, Mark D; Kuss, Daria J; Billieux, Joël

    2016-06-01

    Background and aims Multiplayer Online Battle Arena (MOBA) games have become the most popular type of video games played worldwide, superseding the playing of Massively Multiplayer Online Role-Playing Games and First-Person Shooter games. However, empirical studies focusing on the use and abuse of MOBA games are still very limited, particularly regarding impulsivity, which is an indicator of addictive states but has not yet been explored in MOBA games. In this context, the objective of the present study is to explore the associations between impulsivity and symptoms of addictive use of MOBA games in a sample of highly involved League of Legends (LoL, currently the most popular MOBA game) gamers. Methods Thirty-six LoL gamers were recruited and completed both experimental (Single Key Impulsivity Paradigm) and self-reported impulsivity assessments (s-UPPS-P Impulsive Behavior Scale, Barratt Impulsiveness Scale), in addition to an assessment of problematic video game use (Problematic Online Gaming Questionnaire). Results Results showed links between impulsivity-related constructs and signs of excessive MOBA game involvement. Findings indicated that impaired ability to postpone rewards in an experimental laboratory task was strongly related to problematic patterns of MOBA game involvement. Although less consistent, several associations were also found between self-reported impulsivity traits and signs of excessive MOBA game involvement. Conclusions Despite these results are preliminary and based upon a small (self-selected) sample, the present study highlights potential psychological factors related to the addictive use of MOBA games. PMID:27156376

  5. Femtosecond laser for glaucoma treatment: the comparison between simulation and experimentation results on ocular tissue removal

    NASA Astrophysics Data System (ADS)

    Hou, Dong Xia; Ngoi, Bryan K. A.; Hoh, Sek Tien; Koh, Lee Huat K.; Deng, Yuan Zi

    2005-04-01

    In ophthalmology, the use of femtosecond lasers is receiving more attention than ever due to its extremely high intensity and ultra short pulse duration. It opens the highly beneficial possibilities for minimized side effects during surgery process, and one of the specific areas is laser surgery in glaucoma treatment. However, the sophisticated femtosecond laser-ocular tissue interaction mechanism hampers the clinical application of femtosecond laser to treat glaucoma. The potential contribution in this work lies in the fact, that this is the first time a modified moving breakdown theory is applied, which is appropriate for femtosecond time scale, to analyze femtosecond laser-ocular tissue interaction mechanism. Based on this theory, energy deposition and corresponding thermal increase are studied by both simulation and experimentation. A simulation model was developed using Matlab software, and the simulation result was validated through in-vitro laser-tissue interaction experiment using pig iris. By comparing the theoretical and experimental results, it is shown that femtosecond laser can obtain determined ocular tissue removal, and the thermal damage is evidently reduced. This result provides a promising potential for femtosecond laser in glaucoma treatment.

  6. A perspective on thermal annealing of reactor pressure vessel materials from the viewpoint of experimental results

    SciTech Connect

    Iskander, S.K.; Sokolov, M.A.; Nanstad, R.K.

    1996-04-01

    It is believed that in the next decade or so, several nuclear reactor pressure vessels (RPVs) may exceed the reference temperature limits set by the pressurized thermal shock screening criteria. One of the options to mitigate the effects of irradiation on RPVs is to thermally anneal them to restore the toughness properties that have been degraded by neutron irradiation. This paper summarizes recent experimental results from work performed at the Oak Ridge National Laboratory to study the annealing response, or ``recovery`` of several irradiated RPV steels. The fracture toughness is one of the important properties used in the evaluation of the integrity of RPVs. Optimally, the fracture toughness is measured directly by fracture toughness specimens, such as compact tension or precracked Charpy specimens, but is often inferred from the results of Charpy V-notch impact specimens. The experimental results are compared to the predictions of models for embrittlement recovery which have been developed by Eason et al. Some of the issues in annealing that still need to be resolved are discussed.

  7. Investigation of sonar transponders for offshore wind farms: modeling approach, experimental setup, and results.

    PubMed

    Fricke, Moritz B; Rolfes, Raimund

    2013-11-01

    The installation of offshore wind farms in the German Exclusive Economic Zone requires the deployment of sonar transponders to prevent collisions with submarines. The general requirements for these systems have been previously worked out by the Research Department for Underwater Acoustics and Marine Geophysics of the Bundeswehr. In this article, the major results of the research project "Investigation of Sonar Transponders for Offshore Wind Farms" are presented. For theoretical investigations a hybrid approach was implemented using the boundary element method to calculate the source directivity and a three-dimensional ray-tracing algorithm to estimate the transmission loss. The angle-dependence of the sound field as well as the weather-dependence of the transmission loss are compared to experimental results gathered at the offshore wind farm alpha ventus, located 45 km north of the island Borkum. While theoretical and experimental results are in general agreement, the implemented model slightly underestimates scattering at the rough sea surface. It is found that the source level of 200 dB re 1 μPa at 1 m is adequate to satisfy the detectability of the warning sequence at distances up to 2 NM (≈3.7 km) within a horizontal sector of ±60° if realistic assumptions about signal-processing and noise are made. An arrangement to enlarge the angular coverage is discussed. PMID:24180764

  8. Mechanisms for subcritical penetration into a sandy bottom: experimental and modeling results

    PubMed

    Maguer; Fox; Schmidt; Pouliquen; Bovio

    2000-03-01

    This paper presents preliminary results of a recent study whose overall objectives are to determine the mechanisms contributing significantly to subcritical acoustic penetration into ocean sediments, and to quantify the results for use in sonar performance prediction for the detection of buried objects. In situ acoustic measurements were performed on a sandy bottom whose geoacoustical and geomorphological properties were also measured. A parametric array mounted on a tower moving on a rail was used to insonify hydrophones located above and below the sediment interface. Data covering grazing angles both above and below the nominal critical angle and in the frequency range 2-15 kHz were acquired and processed. The results are compared to two models that account for scattering of sound at the rough water-sediment interface into the sediment. Although all possible mechanisms for subcritical penetration are not modeled, the levels predicted by both models are consistent with the levels observed in the experimental data. For the specific seafloor and experimental conditions examined, the analysis suggests that for frequencies below 5-7 kHz sound penetration into the sediment at subcritical insonification is dominated by the evanescent field, while scattering due to surface roughness is the dominant mechanism at higher frequencies.

  9. Investigation of sonar transponders for offshore wind farms: modeling approach, experimental setup, and results.

    PubMed

    Fricke, Moritz B; Rolfes, Raimund

    2013-11-01

    The installation of offshore wind farms in the German Exclusive Economic Zone requires the deployment of sonar transponders to prevent collisions with submarines. The general requirements for these systems have been previously worked out by the Research Department for Underwater Acoustics and Marine Geophysics of the Bundeswehr. In this article, the major results of the research project "Investigation of Sonar Transponders for Offshore Wind Farms" are presented. For theoretical investigations a hybrid approach was implemented using the boundary element method to calculate the source directivity and a three-dimensional ray-tracing algorithm to estimate the transmission loss. The angle-dependence of the sound field as well as the weather-dependence of the transmission loss are compared to experimental results gathered at the offshore wind farm alpha ventus, located 45 km north of the island Borkum. While theoretical and experimental results are in general agreement, the implemented model slightly underestimates scattering at the rough sea surface. It is found that the source level of 200 dB re 1 μPa at 1 m is adequate to satisfy the detectability of the warning sequence at distances up to 2 NM (≈3.7 km) within a horizontal sector of ±60° if realistic assumptions about signal-processing and noise are made. An arrangement to enlarge the angular coverage is discussed.

  10. Impulsivity in Multiplayer Online Battle Arena Gamers: Preliminary Results on Experimental and Self-Report Measures.

    PubMed

    Nuyens, Filip; Deleuze, Jory; Maurage, Pierre; Griffiths, Mark D; Kuss, Daria J; Billieux, Joël

    2016-06-01

    Background and aims Multiplayer Online Battle Arena (MOBA) games have become the most popular type of video games played worldwide, superseding the playing of Massively Multiplayer Online Role-Playing Games and First-Person Shooter games. However, empirical studies focusing on the use and abuse of MOBA games are still very limited, particularly regarding impulsivity, which is an indicator of addictive states but has not yet been explored in MOBA games. In this context, the objective of the present study is to explore the associations between impulsivity and symptoms of addictive use of MOBA games in a sample of highly involved League of Legends (LoL, currently the most popular MOBA game) gamers. Methods Thirty-six LoL gamers were recruited and completed both experimental (Single Key Impulsivity Paradigm) and self-reported impulsivity assessments (s-UPPS-P Impulsive Behavior Scale, Barratt Impulsiveness Scale), in addition to an assessment of problematic video game use (Problematic Online Gaming Questionnaire). Results Results showed links between impulsivity-related constructs and signs of excessive MOBA game involvement. Findings indicated that impaired ability to postpone rewards in an experimental laboratory task was strongly related to problematic patterns of MOBA game involvement. Although less consistent, several associations were also found between self-reported impulsivity traits and signs of excessive MOBA game involvement. Conclusions Despite these results are preliminary and based upon a small (self-selected) sample, the present study highlights potential psychological factors related to the addictive use of MOBA games.

  11. A Comparison of Experimental and Theoretical Results for Labyrinth Gas Seals. Ph.D. Thesis

    NASA Technical Reports Server (NTRS)

    Scharrer, Joseph Kirk

    1987-01-01

    The basic equations are derived for a two control volume model for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent and isoenergetic. The wall friction factors are determined using the Blasius formula. Jet flow theory is used for the calculation of the recirculation velocity in the cavity. Linearized zeroth and first order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth order pressure distribution is found by satisfying the leakage equation. The circumferential velocity distribution is determined by satisfying the momentum equations. The first order equations are solved by a separation of variable solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to experimental test results.

  12. Heavy vehicle suspension parameters identification and estimation of vertical forces: experimental results

    NASA Astrophysics Data System (ADS)

    Imine, H.; Madani, T.

    2015-02-01

    The aim of the present work is to estimate the vertical forces of heavy vehicle and identify the unknown dynamic parameters using sliding mode observer approach. This observation needs a good knowledge of dynamic parameters such as damping coefficient, spring stiffness, etc. In this paper, suspension stiffness and unsprung masses have been identified. Experimental results carried out on an instrumented tractor have been presented in order to show the quality of the state observation, parameters identification and force estimation. These estimation results are then compared to the measured one coming from the sensors installed in the tractor. Many scenarios have been tested. In this paper, the results coming from zigzag test have been shown and commented.

  13. Experimental results for a two-dimensional supersonic inlet used as a thrust deflecting nozzle

    NASA Technical Reports Server (NTRS)

    Johns, Albert L.; Burstadt, Paul L.

    1984-01-01

    Nearly all supersonic V/STOL aircraft concepts are dependent on the thrust deflecting capability of a nozzle. In one unique concept, referred to as the reverse flow dual fan, not only is there a thrust deflecting nozzle for the fan and core engine exit flow, but because of the way the propulsion system operates during vertical takeoff and landing, the supersonic inlet is also used as a thrust deflecting nozzle. This paper presents results of an experimental study to evaluate the performance of a supersonic inlet used as a thrust deflecting nozzle for this reverse flow dual fan concept. Results are presented in terms of nozzle thrust coefficient and thrust vector angle for a number of inlet/nozzle configurations. Flow visualization and nozzle exit flow survey results are also shown.

  14. Response of solid state track recorders to neutrons. I. Experimental results

    NASA Astrophysics Data System (ADS)

    Haque, A. U.; Besant, C. B.; Hooton, B. W.

    1982-06-01

    Experimental results are presented from a detailed study of CA80-15, Makrofol KG and CR-39 SSTRs for fast neutron measurements in the presence of a high flux of γ-rays. For a fission neutron source, the efficiency in CA80-15 is ˜ 1.4 × 10 - tracks per neutron. These results are in agreement to within ± 15% of the theoretical results. Proton, alpha and recoil particle response characteristics of CR-39 SSTR have also been investigated, showing its excellent proton energy resolution. The large energy range for proton registration and smooth surface of excellent optical quality suggest CR-39 as a suitable material for fast neutron dosimetry using recoil proton tracks.

  15. Soil clean up by venting: comparison between modelling and experimental VOC removal results.

    PubMed

    Brusturean, G A; Todinca, T; Perju, D; Carré, J; Bourgois, J

    2007-10-01

    Many investigations into specific or accidental pollution relate to hydrocarbons of oil origin: fuels (gasoline or gas oil), fuel oil and lubricants. Pollution by petroleum products is a source of volatile organic compounds in soil. Therefore, laboratory column venting experiments were completed in order to investigate the removal of a pure compound (toluene) and a mixture of two (toluene and n-heptane) and five (toluene, n-heptane, ethylbenzene, m-xylene and p-xylene) compounds. The choice of the compounds, as well as their proportion in the mixture was made on the basis of the real fuel composition. The objective of this study is a comparison between the experimental volatile organic compounds removal results and the predicted values of a simple classical analytical mathematical model that enables the modelling of the venting process. The proposed model for the contaminants transport describes the removal of organic compounds from soil, the contaminants being distributed among four phases: vapour, nonaqueous liquid phase, aqueous and "solid" phase; local phases equilibrium and ideal behaviour of all four phases were found to be accurate enough to describe the interphase mass transfer. The testing of the mathematical model accuracy has been done by using the following performance criteria: dynamic absolute error, average error, model accuracy and correlation coefficient. The reasonable agreement between the predicted and the experimental results as well as the values of the performance criteria prove that the mathematical model is suitable to describe the removal of volatile organic compounds pollutants by venting in the range of experimental conditions used in the pilot plant. PMID:17970522

  16. Fuel-rich, catalytic reaction experimental results. [fuel development for high-speed civil transport aircraft

    NASA Technical Reports Server (NTRS)

    Rollbuhler, Jim

    1991-01-01

    Future aeropropulsion gas turbine combustion requirements call for operating at very high inlet temperatures, pressures, and large temperature rises. At the same time, the combustion process is to have minimum pollution effects on the environment. Aircraft gas turbine engines utilize liquid hydrocarbon fuels which are difficult to uniformly atomize and mix with combustion air. An approach for minimizing fuel related problems is to transform the liquid fuel into gaseous form prior to the completion of the combustion process. Experimentally obtained results are presented for vaporizing and partially oxidizing a liquid hydrocarbon fuel into burnable gaseous components. The presented experimental data show that 1200 to 1300 K reaction product gas, rich in hydrogen, carbon monoxide, and light-end hydrocarbons, is formed when flowing 0.3 to 0.6 fuel to air mixes through a catalyst reactor. The reaction temperatures are kept low enough that nitrogen oxides and carbon particles (soot) do not form. Results are reported for tests using different catalyst types and configurations, mass flowrates, input temperatures, and fuel to air ratios.

  17. Comparison of experimental and analytical results for free vibration of laminated composite plates

    SciTech Connect

    Maryuama, Koichi; Narita, Yoshihiro; Ichinomiya, Osamu

    1995-11-01

    Fibrous composite materials are being increasingly employed in high performance structures, including pressured vessel and piping applications. These materials are usually used in the form of laminated flat or curved plates, and the understanding of natural frequencies and the corresponding mode shapes is essential to a reliable structural design. Although many references have been published on analytical study of laminated composite plates, a limited number of experimental studies have appeared for dealing with vibration characteristics of the plates. This paper presents both experimental and analytical results for the problems. In the experiment, the holographic interferometry is used to measure the resonant frequencies and corresponding mode shapes of six-layered CFRP (carbon fiber reinforced plastic) composite plates. The material constants of a lamina are calculated from fiber and matrix material constants by using some different composite rules. With the calculated constants, the natural frequencies of the laminated CFRP plates are theoretically determined by the Ritz method. From the comparison of two sets of the results, the effect of choosing different composite rules is discussed in the vibration study of laminated composite plates.

  18. Epistemology and expectations survey about experimental physics: Development and initial results

    NASA Astrophysics Data System (ADS)

    Zwickl, Benjamin M.; Hirokawa, Takako; Finkelstein, Noah; Lewandowski, H. J.

    2014-06-01

    In response to national calls to better align physics laboratory courses with the way physicists engage in research, we have developed an epistemology and expectations survey to assess how students perceive the nature of physics experiments in the contexts of laboratory courses and the professional research laboratory. The Colorado Learning Attitudes about Science Survey for Experimental Physics (E-CLASS) evaluates students' epistemology at the beginning and end of a semester. Students respond to paired questions about how they personally perceive doing experiments in laboratory courses and how they perceive an experimental physicist might respond regarding their research. Also, at the end of the semester, the E-CLASS assesses a third dimension of laboratory instruction, students' reflections on their course's expectations for earning a good grade. By basing survey statements on widely embraced learning goals and common critiques of teaching labs, the E-CLASS serves as an assessment tool for lab courses across the undergraduate curriculum and as a tool for physics education research. We present the development, evidence of validation, and initial formative assessment results from a sample that includes 45 classes at 20 institutions. We also discuss feedback from instructors and reflect on the challenges of large-scale online administration and distribution of results.

  19. Transport of fluorobenzoate tracers in a vegetated hydrologic control volume: 1. Experimental results

    NASA Astrophysics Data System (ADS)

    Queloz, Pierre; Bertuzzo, Enrico; Carraro, Luca; Botter, Gianluca; Miglietta, Franco; Rao, P. S. C.; Rinaldo, Andrea

    2015-04-01

    This paper reports about the experimental evidence collected on the transport of five fluorobenzoate tracers injected under controlled conditions in a vegetated hydrologic volume, a large lysimeter (fitted with load cells, sampling ports, and an underground chamber) where two willows prompting large evapotranspiration fluxes had been grown. The relevance of the study lies in the direct and indirect measures of the ways in which hydrologic fluxes, in this case, evapotranspiration from the upper surface and discharge from the bottom drainage, sample water and solutes in storage at different times under variable hydrologic forcings. Methods involve the accurate control of hydrologic inputs and outputs and a large number of suitable chemical analyses of water samples in discharge waters. Mass extraction from biomass has also been performed ex post. The results of the 2 year long experiment established that our initial premises on the tracers' behavior, known to be sorption-free under saturated conditions which we verified in column leaching tests, were unsuitable as large differences in mass recovery appeared. Issues on reactivity thus arose and were addressed in the paper, in this case attributed to microbial degradation and solute plant uptake. Our results suggest previously unknown features of fluorobenzoate compounds as hydrologic tracers, potentially interesting for catchment studies owing to their suitability for distinguishable multiple injections, and an outlook on direct experimental closures of mass balance in hydrologic transport volumes involving fluxes that are likely to sample differently stored water and solutes.

  20. Experimental Impeller Fragmentation of Iliocaval Thrombosis Under Tulip Filter Protection: Preliminary Results

    SciTech Connect

    Schmitz-Rode, Thomas; Vorwerk, Dierk; Schuermann, Karl; Guenther, Rolf W.

    1996-04-15

    Purpose: To assess the efficacy of catheter fragmentation of massive caval thrombosis and of filter protection against procedure-related pulmonary embolism. Methods: In 10 sheep, a self-expanding tulip-shaped filter made from Wallstent mesh (diameter 25 mm) was introduced from the right jugular approach into the proximal inferior vena cava. Experimentally induced massive iliocaval thrombosis was fragmented by an impeller catheter (expanded diameter 14 mm), which was advanced coaxially through the sheath of the expanded filter. Post-procedural cavography and pulmonary angiography were performed to document the extent of caval recanalization and pulmonary embolism. Results: In all cases, impeller fragmentation cleared the inferior vena cava and the iliac veins of thrombi completely. Fragments washed downstream were trapped in the filter. In two of the first cases, parts of the clots caused pulmonary embolism before the filter was in place. Further events were avoided by a modification of the experimental setup. Except for some small peripheral perfusion defects in two cases, pulmonary angiograms did not show any incidence of pulmonary embolism. Conclusion: Our preliminary results suggest that impeller fragmentation of iliocaval thrombi under tulip filter protection is effective and does not cause significant pulmonary embolism.

  1. Thermal conductivity of silicic tuffs: predictive formalism and comparison with preliminary experimental results

    SciTech Connect

    Lappin, A. R.

    1980-07-01

    Performance of both near- and far-field thermomechanical calculations to assess the feasibility of waste disposal in silicic tuffs requires a formalism for predicting thermal conductivity of a broad range of tuffs. This report summarizes the available thermal conductivity data for silicate phases that occur in tuffs and describes several grain-density and conductivity trends which may be expected to result from post-emplacement alteration. A bounding curve is drawn that predicts the minimum theoretical matrix (zero-porosity) conductivity for most tuffs as a function of grain density. Comparison of experimental results with this curve shows that experimental conductivities are consistently lower at any given grain density. Use of the lowered bounding curve and an effective gas conductivity of 0.12 W/m{sup 0}C allows conservative prediction of conductivity for a broad range of tuff types. For the samples measured here, use of the predictive curve allows estimation of conductivity to within 15% or better, with one exception. Application and possible improvement of the formalism are also discussed.

  2. Low pollution combustor designs for CTOL engines - Results of the Experimental Clean Combustor Program

    NASA Technical Reports Server (NTRS)

    Roberts, R.; Peduzzi, A.; Niedzwiecki, R. W.

    1976-01-01

    The NASA/Pratt & Whitney Aircraft Experimental Clean Combustor Program is a multi-year, major contract effort. Primary program objectives are the generation of combustor technology for development of advanced commercial CTOL engines with lower exhaust emissions than current aircraft and demonstration of this technology in a full-scale JT9D engine in 1976. This paper describes the pollution and performance goals, Phase I and II test results, and the Phase III combustor hardware, pollution sampling techniques, and test plans. Best results were obtained with the Vorbix concept which employs multiple burning zones and improved fuel preparation and distribution. Substantial reductions were achieved in all pollutant categories, meeting the 1979 EPA standards for NOx, THC, and smoke when extrapolated to JT9D cycle conditions. The Vorbix concept additionally demonstrated the capability for acceptable altitude relight and did not appear to have unsolvable durability or exit temperature distribution problems.

  3. Non-Shock Initiation of the Plastic Bonded Explosive PBXN-5: Experimental Results

    NASA Astrophysics Data System (ADS)

    Lappo, K. N.; Todd, S. N.; Anderson, M. U.; Vogler, T. J.

    2007-12-01

    The plastic bonded explosive PBXN-5 was studied under impulsive loading experiments to relate impact-induced mechanical damage to the onset of, and the extent of reaction produced. A small diameter projectile generated shock and release conditions at the impact interface, on the microsecond time scale during the initial portion of the impulsive loading. These shock and release wave interactions generate significant damage, resulting in a porous, powder compaction-type initiation behavior. Experimental measurements show an energy threshold for initiation of reaction which relates to impact-induced kinetic energy. These results are implemented in the model development and validation phases of the damage-induced reaction (DMGIR) model, which is used to simulate impact scenarios of explosives, explosive components, and explosive systems.

  4. Experimental results for improving the matrix condition using a hybrid optical system.

    PubMed

    Klapp, Iftach; Mendlovic, David

    2012-03-01

    We present preliminary experimental results for implementing the "blurred trajectories" method on three parallel optics (PO) systems. The "main" system and "auxiliary" optics were simple laboratory graded lenses attached to an iris diaphragm. When applying the blurred trajectories method we first show an improvement in the matrix condition, as the matrix condition number decreased in a range of factors of 3 to 418 relative to the main system. Following that, image restoration by weak regularization was performed so that the system matrix condition dominated the restoration process. It was shown that the restoration results of the PO are better than those of the main system and the auxiliary optics separately. In addition, the quality of the restoration follows the system's matrix condition. The improvement in the matrix condition achieved by the PO system improved the immunity to detection noise. Finally, a comparison to Wiener filtering restoration shows that it is also generally inferior to the proposed method.

  5. Experimental and raytrace results for throat-to-throat compound parabolic concentrators

    SciTech Connect

    Leviton, D.B.; Leitch, J.W.

    1986-08-15

    Compound parabolic concentrators are nonimaging cone-shaped optics with useful angular transmission characteristics. Two cones used throat-to-throat accept radiant flux within one well-defined acceptance angle and redistribute it into another. If the entrance cone is fed with Lambertian flux, the exit cone produces a beam whose half-angle is the exit cone's acceptance angle and whose cross section shows uniform irradiance from near the exit mouth to infinity. (The pair is a beam angle transformer.) We discuss the design of one pair of cones, an experiment to map the irradiance of the emergent beam, and a raytracing program which models the cones fed by Lambertian flux. Experimental results compare favorably with raytrace results.

  6. Experimental results on the design for the APS PID global orbit control system.

    SciTech Connect

    Chung, Y.; Kirchman, J. A.

    1997-12-05

    The Advanced Photon Source third generation synchrotrons light source needs a stabilized particle beam position to produce high brightness and low emittance radiation. Global orbit correction control is introduced and is utilized to satisfy the demanding needs of the accelerator. This paper presents the experimental results for determining an effective and optimal controller to meet the global orbit correction requirements. These requirements include frequency/time domain demands consisting of vibrational noise attenuation, limiting of controller gains for stability and improving the system time response. Experiments were conducted with a digital signal processor implementing various PID sets to make comparisons between simulations and experiments. Measurements at these PID sets supported the results of software simulation.

  7. Survey of Experimental Results in High-Contrast Imaging for Future Exoplanet Missions

    NASA Technical Reports Server (NTRS)

    Lawson, P. R.; Belikov, R.; Cash, W.; Clampin, M.; Glassman, T.; Guyon, O.; Kasdin, N. J.; Kern, B. D.; Lyon, R.; Mawet, D.; Moody, D.; Samuele, R.; Serabyn, E.; Sirbu, D.; Trauger, J.

    2013-01-01

    We present and compare experimental results in high contrast imaging representing the state of the art in coronagraph and starshade technology. These experiments have been undertaken with the goal of demonstrating the capability of detecting Earth-like planets around nearby Sun-like stars. The contrast of an Earth seen in reflected light around a Sun-like star would be about 1.2 x 10(exp -10). Several of the current candidate technologies now yield raw contrasts of 1.0 x 10(exp -9) or better, and so should enable the detection of Earths, assuming a gain in sensitivity in post-processing of a factor of 10. We present results of coronagraph and starshade experiments conducted at visible and infrared wavelengths. Cross-sections of dark fields are directly compared as a function of field angle and bandwidth. The strength and differences of the techniques are compared.

  8. Preliminary results of the large experimental wind turbine phase of the national wind energy program

    NASA Technical Reports Server (NTRS)

    Thomas, R. L.; Sholes, J. E.

    1975-01-01

    A major phase of the wind energy program is the development of reliable wind turbines for supplying cost-competitive electrical energy. This paper discusses the preliminary results of two projects in this phase of the program. First an experimental 100 kW wind turbine design and its status are reviewed. Also discussed are the results of two parallel design studies for determining the configurations and power levels for wind turbines with minimum energy costs. These studies show wind energy costs of 7 to 1.5 c/kWH for wind turbines produced in quantities of 100 to 1000 a year and located at sites having average winds of 12 to 18 mph.

  9. The Langley Research Center CSI phase-0 evolutionary model testbed-design and experimental results

    NASA Technical Reports Server (NTRS)

    Belvin, W. K.; Horta, Lucas G.; Elliott, K. B.

    1991-01-01

    A testbed for the development of Controls Structures Interaction (CSI) technology is described. The design philosophy, capabilities, and early experimental results are presented to introduce some of the ongoing CSI research at NASA-Langley. The testbed, referred to as the Phase 0 version of the CSI Evolutionary model (CEM), is the first stage of model complexity designed to show the benefits of CSI technology and to identify weaknesses in current capabilities. Early closed loop test results have shown non-model based controllers can provide an order of magnitude increase in damping in the first few flexible vibration modes. Model based controllers for higher performance will need to be robust to model uncertainty as verified by System ID tests. Data are presented that show finite element model predictions of frequency differ from those obtained from tests. Plans are also presented for evolution of the CEM to study integrated controller and structure design as well as multiple payload dynamics.

  10. An Experimental Investigation of the Droplet Deformation Process Resulting from Binary Collisions of a Viscous Fluid

    NASA Astrophysics Data System (ADS)

    Willis, Keeney; Orme, Melissa

    1997-11-01

    An experimental investigation of the collisional dynamics of equal sized drops of a viscous, silicone based oil, DC 200, has been conducted for head-on impacts in a vacuum. Results show that the range of droplet Weber numbers necessary to describe the boundaries between permanent coalescence and what has been previously described as reflexive separation, is several orders of magnitude higher than has been reported in studies involving water and hydrocarbon fuel droplets. Energy dissipation during the deformation process has been measured, and the results show a wide discrepancy with available theory. Detailed observations of the post-impact deformation process reveals that in this case, the formation of multiple drops is due solely to the growth of Rayleigh instabilities on the extended fluid ligament.

  11. Comparison of results of experimental research with numerical calculations of a model one-sided seal

    NASA Astrophysics Data System (ADS)

    Joachimiak, Damian; Krzyślak, Piotr

    2015-06-01

    Paper presents the results of experimental and numerical research of a model segment of a labyrinth seal for a different wear level. The analysis covers the extent of leakage and distribution of static pressure in the seal chambers and the planes upstream and downstream of the segment. The measurement data have been compared with the results of numerical calculations obtained using commercial software. Based on the flow conditions occurring in the area subjected to calculations, the size of the mesh defined by parameter y+ has been analyzed and the selection of the turbulence model has been described. The numerical calculations were based on the measurable thermodynamic parameters in the seal segments of steam turbines. The work contains a comparison of the mass flow and distribution of static pressure in the seal chambers obtained during the measurement and calculated numerically in a model segment of the seal of different level of wear.

  12. Experimental and raytrace results for throat-to-throat compound parabolic concentrators

    NASA Technical Reports Server (NTRS)

    Leviton, D. B.; Leitch, J. W.

    1986-01-01

    Compound parabolic concentrators are nonimaging cone-shaped optics with useful angular transmission characteristics. Two cones used throat-to-throat accept radiant flux within one well-defined acceptance angle and redistribute it into another. If the entrance cone is fed with Lambertian flux, the exit cone produces a beam whose half-angle is the exit cone's acceptance angle and whose cross section shows uniform irradiance from near the exit mouth to infinity. (The pair is a beam angle transformer). The design of one pair of cones is discussed, also an experiment to map the irradiance of the emergent beam, and a raytracing program which models the cones fed by Lambertian flux. Experimental results compare favorably with raytrace results.

  13. Experimental Results for a Flapped Natural-laminar-flow Airfoil with High Lift/drag Ratio

    NASA Technical Reports Server (NTRS)

    Mcghee, R. J.; Viken, J. K.; Pfenninger, W.; Beasley, W. D.; Harvey, W. D.

    1984-01-01

    Experimental results have been obtained for a flapped natural-laminar-flow airfoil, NLF(1)-0414F, in the Langley Low-Turbulence Pressure Tunnel. The tests were conducted over a Mach number range from 0.05 to 0.40 and a chord Reynolds number range from about 3.0 x 10(6) to 22.0 x 10(6). The airfoil was designed for 0.70 chord laminar flow on both surfaces at a lift coefficient of 0.40, a Reynolds number of 10.0 x 10(6), and a Mach number of 0.40. A 0.125 chord simple flap was incorporated in the design to increase the low-drag, lift-coefficient range. Results were also obtained for a 0.20 chord split-flap deflected 60 deg.

  14. Heat Transfer Enhancement for Finned-Tube Heat Exchangers with Vortex Generators: Experimental and Numerical Results

    SciTech Connect

    O'Brien, James Edward; Sohal, Manohar Singh; Huff, George Albert

    2002-08-01

    A combined experimental and numerical investigation is under way to investigate heat transfer enhancement techniques that may be applicable to large-scale air-cooled condensers such as those used in geothermal power applications. The research is focused on whether air-side heat transfer can be improved through the use of finsurface vortex generators (winglets,) while maintaining low heat exchanger pressure drop. A transient heat transfer visualization and measurement technique has been employed in order to obtain detailed distributions of local heat transfer coefficients on model fin surfaces. Pressure drop measurements have also been acquired in a separate multiple-tube row apparatus. In addition, numerical modeling techniques have been developed to allow prediction of local and average heat transfer for these low-Reynolds-number flows with and without winglets. Representative experimental and numerical results presented in this paper reveal quantitative details of local fin-surface heat transfer in the vicinity of a circular tube with a single delta winglet pair downstream of the cylinder. The winglets were triangular (delta) with a 1:2 height/length aspect ratio and a height equal to 90% of the channel height. Overall mean fin-surface Nusselt-number results indicate a significant level of heat transfer enhancement (average enhancement ratio 35%) associated with the deployment of the winglets with oval tubes. Pressure drop measurements have also been obtained for a variety of tube and winglet configurations using a single-channel flow apparatus that includes four tube rows in a staggered array. Comparisons of heat transfer and pressure drop results for the elliptical tube versus a circular tube with and without winglets are provided. Heat transfer and pressure-drop results have been obtained for flow Reynolds numbers based on channel height and mean flow velocity ranging from 700 to 6500.

  15. Recovery of yttrium from cathode ray tubes and lamps’ fluorescent powders: experimental results and economic simulation

    SciTech Connect

    Innocenzi, V. De Michelis, I.; Ferella, F.; Vegliò, F.

    2013-11-15

    Highlights: • Fluorescent powder of lamps. • Fluorescent powder of cathode ray rubes. • Recovery of yttrium from fluorescent powders. • Economic simulation for the processes to recover yttrium from WEEE. - Abstract: In this paper, yttrium recovery from fluorescent powder of lamps and cathode ray tubes (CRTs) is described. The process for treating these materials includes the following: (a) acid leaching, (b) purification of the leach liquors using sodium hydroxide and sodium sulfide, (c) precipitation of yttrium using oxalic acid, and (d) calcinations of oxalates for production of yttrium oxides. Experimental results have shown that process conditions necessary to purify the solutions and recover yttrium strongly depend on composition of the leach liquor, in other words, whether the powder comes from treatment of CRTs or lamp. In the optimal experimental conditions, the recoveries of yttrium oxide are about 95%, 55%, and 65% for CRT, lamps, and CRT/lamp mixture (called MIX) powders, respectively. The lower yields obtained during treatments of MIX and lamp powders are probably due to the co-precipitation of yttrium together with other metals contained in the lamps powder only. Yttrium loss can be reduced to minimum changing the experimental conditions with respect to the case of the CRT process. In any case, the purity of final products from CRT, lamps, and MIX is greater than 95%. Moreover, the possibility to treat simultaneously both CRT and lamp powders is very important and interesting from an industrial point of view since it could be possible to run a single plant treating fluorescent powder coming from two different electronic wastes.

  16. Thermodiffusion in concentrated ferrofluids: Experimental and numerical results on magnetic thermodiffusion

    NASA Astrophysics Data System (ADS)

    Sprenger, Lisa; Lange, Adrian; Odenbach, Stefan

    2014-02-01

    Ferrofluids consist of magnetic nanoparticles dispersed in a carrier liquid. Their strong thermodiffusive behaviour, characterised by the Soret coefficient, coupled with the dependency of the fluid's parameters on magnetic fields is dealt with in this work. It is known from former experimental investigations on the one hand that the Soret coefficient itself is magnetic field dependent and on the other hand that the accuracy of the coefficient's experimental determination highly depends on the volume concentration of the fluid. The thermally driven separation of particles and carrier liquid is carried out with a concentrated ferrofluid (φ = 0.087) in a horizontal thermodiffusion cell and is compared to equally detected former measurement data. The temperature gradient (1 K/mm) is applied perpendicular to the separation layer. The magnetic field is either applied parallel or perpendicular to the temperature difference. For three different magnetic field strengths (40 kA/m, 100 kA/m, 320 kA/m) the diffusive separation is detected. It reveals a sign change of the Soret coefficient with rising field strength for both field directions which stands for a change in the direction of motion of the particles. This behaviour contradicts former experimental results with a dilute magnetic fluid, in which a change in the coefficient's sign could only be detected for the parallel setup. An anisotropic behaviour in the current data is measured referring to the intensity of the separation being more intense in the perpendicular position of the magnetic field: ST‖ = -0.152 K-1 and ST⊥ = -0.257 K-1 at H = 320 kA/m. The ferrofluiddynamics-theory (FFD-theory) describes the thermodiffusive processes thermodynamically and a numerical simulation of the fluid's separation depending on the two transport parameters ξ‖ and ξ⊥ used within the FFD-theory can be implemented. In the case of a parallel aligned magnetic field, the parameter can be determined to ξ‖ = {2.8; 9.1; 11.2}

  17. Experimental and numerical results on the fluid flow driven by a traveling magnetic field

    NASA Astrophysics Data System (ADS)

    Lantzsch, R.; Galindo, V.; Grants, I.; Zhang, C.; Pätzold, O.; Gerbeth, G.; Stelter, M.

    2007-07-01

    A traveling magnetic field (TMF) driven flow and its transition from a laminar to a time-dependent flow is studied by means of ultrasonic Doppler velocimetry and numerical simulations. The experimental setup comprises a cylindrical cavity containing the electrically conducting model fluid GaInSn and a system of six equidistant coils, which are fed by an out-of-phase current to create an up- or downward directed TMF. Hence, a Lorentz force is induced in the melt which leads to meridional flow patterns. For numerical simulations commercial codes (Opera/Fidap) and a spectral code are used. The characteristic parameters of the magnetohydrodynamic model system are chosen close to the conditions used for vertical gradient freeze (VGF) crystal growth. The axisymmetric basic flow and its dependence on the dimensionless shielding parameter S are examined. It is shown that, for S>10, the flow velocity decreases significantly, whereas almost no influence is found for a smaller shielding parameter. The critical Reynolds number for the onset of instability is found in the range of 300-450. Good agreement between experimental results and the numerical simulations is achieved.

  18. A review of thin layer drying of foods: theory, modeling, and experimental results.

    PubMed

    Erbay, Zafer; Icier, Filiz

    2010-05-01

    Drying is a complicated process with simultaneous heat and mass transfer, and food drying is especially very complex because of the differential structure of products. In practice, a food dryer is considerably more complex than a device that merely removes moisture, and effective models are necessary for process design, optimization, energy integration, and control. Although modeling studies in food drying are important, there is no theoretical model which neither is practical nor can it unify the calculations. Therefore the experimental studies prevent their importance in drying and thin layer drying equations are important tools in mathematical modeling of food drying. They are practical and give sufficiently good results. In this study first, the theory of drying was given briefly. Next, general modeling approaches for food drying were explained. Then, commonly used or newly developed thin layer drying equations were shown, and determination of the appropriate model was explained. Afterwards, effective moisture diffusivity and activation energy calculations were expressed. Finally, experimental studies conducted in the last 10 years were reviewed, tabulated, and discussed. It is expected that this comprehensive study will be beneficial to those involved or interested in modeling, design, optimization, and analysis of food drying. PMID:20373189

  19. Experimental results and modeling tests of an adsorptive air-conditioning unit

    SciTech Connect

    Guilleminot, J.J.; Poyelle, F.; Meunier, F.

    1998-10-01

    Experimental tests have been performed on a zeolite-water adsorptive system suitable for air conditioning and consisting of two adsorbers filled with a consolidated composite made of zeolite mixed with a highly conductive matrix. This paper describes the experimental results of such a heat pump unit operating with a heat and mass recovery cycle. An important enhancement of the specific cooling power (SCP) has been achieved. At evaporating temperature T = 4 C, mass transfer resistance controls the process and limits the expected COP. Tests carried out at higher evaporating pressure make it possible to achieve the predicted COP and SCP. A predictive model developed and validated elsewhere in order to describe the temperature evolution of components and the heat and mass transfer in the adsorbers explains the mass transfer resistance in the adsorbent. Last, a new highly conductive adsorbent composite with good mass transfer properties is developed. The model is used to predict the performances of this new material. Very good SCP and COP can be achieved.

  20. Structural and vibrational study of graphene oxide via coronene based models: theoretical and experimental results

    NASA Astrophysics Data System (ADS)

    Almeida de Mendonça, João Paulo; Henrique de Lima, Alessandro; Amaral Junqueira, Georgia Maria; Gianini Quirino, Welber; Legnani, Cristiano; Oliveira Maciel, Indhira; Sato, Fernando

    2016-05-01

    We use the Coronene (C24H12), a simple and finite molecule, to make a model to study the spectroscopic and structural alterations generated by oxygenated groups in graphene oxide (GO). Based on the Lerf-Klinowski model, we chose the hydroxyl [OH-], the carboxyl [COOH-] and the epoxy [the ring C2O inside the molecule] as our radicals of interest and study their collective and isolated effects. We perform geometry optimization, vibrational IR (via AM1 and DFT-B3LYP) and Raman spectra (via DFT-B3LYP) of a series of functionalized coronene molecules. As results, we obtain some useful data for the analysis of IR and Raman spectra of GO, which facilitate the understanding and identification of the peaks found in the experiment. Finally, we suggest a new model to study GO, producing an accurate signature when compared to our experimental data. Such molecule shows in more details of the structural effects caused by functionalization when compared to experimental data.

  1. Experimental Estimation Of Energy Damping During Free Rocking Of Unreinforced Masonry Walls. First Results

    SciTech Connect

    Sorrentino, Luigi; Masiani, Renato; Benedetti, Stefano

    2008-07-08

    This paper presents an ongoing experimental program on unreinforced masonry walls undergoing free rocking. Aim of the laboratory campaign is the estimation of kinetic energy damping exhibited by walls released with non-zero initial conditions of motion. Such energy damping is necessary for dynamic modelling of unreinforced masonry local mechanisms. After a brief review of the literature on this topic, the main features of the laboratory tests are presented. The program involves the experimental investigation of several parameters: 1) unit material (brick or tuff), 2) wall aspect ratio (ranging between 14.5 and 7.1), 3) restraint condition (two-sided or one-sided rocking), and 4) depth of the contact surface between facade and transverse walls (one-sided rocking only). All walls are single wythe and the mortar is pozzuolanic. The campaign is still in progress. However, it is possible to present the results on most of the mechanical properties of mortar and bricks. Moreover, a few time histories are reported, already indicating the need to correct some of the assumptions frequent in the literature.

  2. Alfven Wave Generation by a Rotating Magnetic Field Source: Theory, Modeling and Experimental Results

    NASA Astrophysics Data System (ADS)

    Sharma, A. S.; Karavaev, A. V.; Gumerov, N.; Shao, X.; Papadopoulos, K.; Gekelman, W.; Wang, Y.; Vincena, S.; Pribyl, P.

    2010-11-01

    Recent experiments conducted in the Large Plasma Device (LAPD) located at UCLA demonstrated efficient excitation of whistler and shear Alfven waves by a Rotating Magnetic Field (RMF) source. We present analytical theory, computational modeling and experimental results of the shear Alfven wave excitation by RMF source created by a phased orthogonal two-loop antenna in a plasma. An analytical theory and simulations using a three-dimensional cold two-fluid model of Alfven wave excitation were developed and compared with experiments. These comparisons show good agreement on linear shear Alfven wave properties, namely, spatio-temporal wave structure, dispersion relation, and the dependence of wave magnitude on the wave frequency. From the simulations it was found that the energy of the Alfven wave generated by the rotating magnetic field source is distributed among the kinetic energies of ions and electrons and the electromagnetic energy of the wave. The wave magnetic field power calculated from the experimental data and using a fluid model agrees within ˜1 percent. The RMF source is thus very efficient in generating shear Alfven waves. Work supported by ONR MURI grant.

  3. Alfven Wave Generation by a Rotating Magnetic Field Source: Theory, Modeling and Experimental Results

    NASA Astrophysics Data System (ADS)

    Shao, X.; Karavaev, A. V.; Gumerov, N.; Sharma, A. S.; Papadopoulos, K.; Gekelman, W. N.; Wang, Y.; Vincena, S. T.; Pribyl, P.

    2010-12-01

    Recent experiments conducted in the Large Plasma Device (LAPD) located at UCLA demonstrated efficient excitation of whistler and shear Alfven waves by a Rotating Magnetic Field (RMF) source. We present analytical theory, computational modeling and experimental results of the shear Alfven wave excitation by RMF source created by a phased orthogonal two-loop antenna in a plasma. An analytical theory and simulations using a three-dimensional cold two-fluid model of Alfven wave excitation were developed and compared with experiments. These comparisons show good agreement on linear shear Alfven wave properties, namely, spatio-temporal wave structure, dispersion relation, and the dependence of wave magnitude on the wave frequency. From the simulations it was found that the energy of the Alfven wave generated by the rotating magnetic field source is distributed among the kinetic energies of ions and electrons and the electromagnetic energy of the wave. The wave magnetic field power calculated from the experimental data and using a fluid model agrees within 1 percent. The RMF source is thus very efficient in generating shear Alfven waves. Work supported by ONR MURI grant.

  4. Preliminary results of the LLNL airborne experimental test-bed SAR system

    SciTech Connect

    Miller, M.G.; Mullenhoff, C.J.; Kiefer, R.D.; Brase, J.M.; Wieting, M.G.; Berry, G.L.; Jones, H.E.

    1996-01-16

    The Imaging and Detection Program (IDP) within Laser Programs at Lawrence Livermore National Laboratory (LLNL) in cooperation with the Hughes Aircraft Company has developed a versatile, high performance, airborne experimental test-bed (AETB) capability. The test-bed has been developed for a wide range of research and development experimental applications including radar and radiometry plus, with additional aircraft modifications, optical systems. The airborne test-bed capability has been developed within a Douglas EA-3B Skywarrior jet aircraft provided and flown by Hughes Aircraft Company. The current test-bed payload consists of an X-band radar system, a high-speed data acquisition, and a real-time processing capability. The medium power radar system is configured to operate in a high resolution, synthetic aperture radar (SAR) mode and is highly configurable in terms of waveforrns, PRF, bandwidth, etc. Antennas are mounted on a 2-axis gimbal in the belly radome of the aircraft which provides pointing and stabilization. Aircraft position and antenna attitude are derived from a dedicated navigational system and provided to the real-time SAR image processor for instant image reconstruction and analysis. This paper presents a further description of the test-bed and payload subsystems plus preliminary results of SAR imagery.

  5. Experimental muscle pain results in reorganization of coordination among trapezius muscle subdivisions during repetitive shoulder flexion.

    PubMed

    Falla, Deborah; Farina, Dario; Graven-Nielsen, Thomas

    2007-04-01

    The aim of the study was to examine the effect of experimental unilateral upper trapezius muscle pain on the relative activation of trapezius muscle subdivisions bilaterally during repetitive movement of the upper limb. Surface EMG signals were detected from nine healthy subjects from the upper, middle and lower divisions of trapezius during a repetitive bilateral shoulder flexion task. Measurements were performed before and after injection of 0.5 ml hypertonic (pain condition) and isotonic (control) saline into the upper division of the right trapezius muscle in two experimental sessions. On the painful side, upper trapezius showed decreased EMG amplitude (average rectified value, ARV) and lower trapezius increased ARV throughout the entire task following the injection of hypertonic saline (40.0 +/- 22.2 vs. 26.0 +/- 17.4 microV, and 12.5 +/- 7.6 vs. 25.6 +/- 14.8 microV, respectively, at the beginning of the contraction). On the side contralateral to pain, greater estimates of ARV were identified for the upper division of trapezius as the task progressed (37.4 +/- 20.2 vs. 52.7 +/- 28.4 microV, at the end of the contraction). Muscle fiber conduction velocity did not change with pain in all three divisions of the right trapezius muscle. The results suggest that local elicitation of nociceptive afferents in the upper division of the trapezius induces reorganization in the coordinated activity of the three subdivisions of the trapezius in repetitive dynamic tasks.

  6. Comparison between Theoretical Calculation and Experimental Results of Excitation Functions for Production of Relevant Biomedical Radionuclides

    SciTech Connect

    Menapace, E.; Birattari, C.; Bonardi, M.L.; Groppi, F.; Morzenti, S.; Zona, C.

    2005-05-24

    The radionuclide production for biomedical applications has been brought up in the years, as a special nuclear application, at INFN LASA Laboratory, particularly in co-operation with the JRC-Ispra of EC. Mainly scientific aspects concerning radiation detection and the relevant instruments, the measurements of excitation functions of the involved nuclear reactions, the requested radiochemistry studies and further applications have been investigated. On the side of the nuclear data evaluations, based on nuclear model calculations and critically selected experimental data, the appropriate competence has been developed at ENEA Division for Advanced Physics Technologies. A series of high specific activity accelerator-produced radionuclides in no-carrier-added (NCA) form, for uses in metabolic radiotherapy and for PET radiodiagnostics, are investigated. In this work, last revised measurements and model calculations are reviewed for excitation functions of natZn(d,X)64Cu, 66Ga reactions, referring to irradiation experiments at K=38 variable energy Cyclotron of JRC-Ispra. Concerning the reaction data for producing 186gRe and 211At/211gPo (including significant emission spectra) and 210At, most recent and critically selected experimental results are considered and discussed in comparison with model calculations paying special care to pre-equilibrium effects estimate and to the appropriate overall parameterization. Model calculations are presented for 226Ra(p,2n)225Ac reaction, according to the working program of the ongoing IAEA CRP on the matter.

  7. A new optical system for the determination of deformations and strains: calibration characteristics and experimental results.

    PubMed

    Derwin, K A; Soslowsky, L J; Green, W D; Elder, S H

    1994-10-01

    Many types of optical strain measurement systems have been used for the determination of deformations and strains in soft biological tissues. The purpose of this investigation is to report a new optical strain measurement system developed in our laboratory which offers distinct advantages over systems developed in the past. Our optical strain system has demonstrated excellent performance in calibration and experimental tests. Calibration tests illustrate the system's accuracy to 0.05% strain at 3.52% strain and 0.18% strain at 11.74% strain. Further, this system can measure strains to within 2% measurement error for strains in a 0-11.74% range when 100 microns increments of motion are used for calibration. The resolution of our system appears to be at least as good as the linear micrometer (2 microns) used as a calibrating standard. Errors in strain measurement due to whole specimen rotation or translation are quantified. Rotations about an in-plane axis perpendicular to the direction of strain and translations in/out of the plane of focus result in the largest sources of error. Finally, in an in vitro biomechanical study of the rabbit Achilles tendon, experimental failure strains are 4.3 +/- 0.9% using this system. PMID:7962015

  8. Numerical and experimental study of local heat transfer enhancement in helically coiled pipes. Preliminary results.

    NASA Astrophysics Data System (ADS)

    Bozzoli, F.; Cattani, L.; Rainieri, S.; Zachár, A.

    2015-11-01

    In the last years, the attention of heat transfer equipments manufacturers turned toward helically coiled-tube heat exchangers, especially with regards to applications for viscous and/or particulate products. The recent progress achieved in numerical simulation motivated many research groups to develop numerical models for this kind of apparatuses. These models, intended both to improve the knowledge of the fundamental heat transfer mechanisms in curved geometries and to support the industrial design of this kind of apparatuses, are usually validated throughout the comparison with either theoretical or experimental evidences by considering average heat transfer performances. However, this approach doesn't guarantee that the validated models are able to reproduce local effects in details, which are so important in this kind of non-standard geometries. In the present paper a numerical model of convective heat transfer in coiled tubes for laminar flow regime was formulated and discussed. Its goodness was checked throughout the comparison with the latest experimental outcomes of Bozzoli et al. [1] in terms of convective heat flux distribution along the boundary of the duct, by ensuring the effectiveness of the model also in the description of local behaviours. Although the present paper reports only preliminary results of this simulation/validation process, it could be of interest for the research community because it proposes a novel approach that could be useful to validate many numerical models for nonstandard geometries.

  9. Fate and Transport of Graphene Oxide in Granular Porous Media: Experimental Results and Modeling

    NASA Astrophysics Data System (ADS)

    Gao, Bin

    2014-05-01

    Although graphene oxide (GO) has been used in many applications to improve human life quality, its environmental fate and behavior are still largely unknown. In this work, a range of laboratory experiments were conducted to explore the aggregation, deposition, and transport mechanisms of GO nano-sheets in porous media under various conditions. Stability experimental data showed that both cation valence and pH showed significant effect on the aggregation of GO sheets. The measured critical coagulation concentrations were in good agreement with the predictions of the extended Schulze-Hardy rule. Sand column experimental results indicated that deposition and transport of GO in porous media were strongly dependent on solution ionic strength. Particularly, GO showed high mobility under low ionic strength conditions in both saturated and unsaturated columns. Increasing ionic strength dramatically increased the retention of GO in porous media, mainly through secondary-minimum deposition. Recovery rates of GO in unsaturated sand columns were lower than that in saturated columns under the same ionic strength conditions, suggesting moisture content also played an important role in the retention of GO in porous media. Findings from the bubble column experiments showed that the GO did not attach to the air-water interface, which is consistent with the XDLVO predictions. Additional retention mechanisms, such as film straining, thus could be responsible to the reduced mobility of GO in unsaturated porous media. The breakthrough curves of GO in saturated and unsaturated columns could be accurately simulated by an advection-dispersion-reaction model.

  10. Drying in porous media with gravity-stabilized fronts: experimental results.

    PubMed

    Yiotis, A G; Salin, D; Tajer, E S; Yortsos, Y C

    2012-08-01

    In a recent paper [Yiotis et al., Phys. Rev. E 85, 046308 (2012)] we developed a model for the drying of porous media in the presence of gravity. It incorporated effects of corner film flow, internal and external mass transfer, and the effect of gravity. Analytical results were derived when gravity opposes drying and hence leads to a stable percolation drying front. In this paper, we test the theory using laboratory experiments. A series of isothermal drying experiments in glass bead packings saturated with volatile hydrocarbons is conducted. The transparent glass cells containing the packing allow for the visual monitoring of the phase distribution patterns below the surface, including the formation of liquid films, as the gaseous phase invades the pore space, and for the control of the thickness of the diffusive mass boundary layer over the packing. The experimental results agree very well with theory, provided that the latter is generalized to account for the effects of corner roundness in the film region (which was neglected in the theoretical part). We demonstrate the existence of an early constant rate period (CRP), which lasts as long as the films saturate the surface of the packing, and of a subsequent falling rate period (FRP), which begins practically after the detachment of the film tips from the external surface. During the CRP, the process is controlled by diffusion within the stagnant gaseous phase in the upper part of the cells, yielding a Stefan tube problem solution. During the FRP, the process is controlled by diffusion within the packing, with a drying rate inversely proportional to the observed position of the film tips in the cell. Theoretical and experimental results compare favorably for a specific value of the roundness of the films, which is found to be constant and equal to 0.2 for various conditions, and verify the theoretical dependence on the capillary Ca(f), Bond Bo, and Sherwood Sh numbers.

  11. Experimental Results from the Thermal Energy Storage-1 (TES-1) Flight Experiment

    NASA Technical Reports Server (NTRS)

    Wald, Lawrence W.; Tolbert, Carol; Jacqmin, David

    1995-01-01

    The Thermal Energy Storage-1 (TES-1) is a flight experiment that flew on the Space Shuttle Columbia (STS-62), in March 1994, as part of the OAST-2 mission. TES-1 is the first experiment in a four experiment suite designed to provide data for understanding the long duration microgravity behavior of thermal energy storage fluoride salts that undergo repeated melting and freezing. Such data have never been obtained before and have direct application for the development of space-based solar dynamic (SD) power systems. These power systems will store solar energy in a thermal energy salt such as lithium fluoride or calcium fluoride. The stored energy is extracted during the shade portion of the orbit. This enables the solar dynamic power system to provide constant electrical power over the entire orbit. Analytical computer codes have been developed for predicting performance of a spaced-based solar dynamic power system. Experimental verification of the analytical predictions is needed prior to using the analytical results for future space power design applications. The four TES flight experiments will be used to obtain the needed experimental data. This paper will focus on the flight results from the first experiment, TES-1, in comparison to the predicted results from the Thermal Energy Storage Simulation (TESSIM) analytical computer code. The TES-1 conceptual development, hardware design, final development, and system verification testing were accomplished at the NASA lewis Research Center (LeRC). TES-1 was developed under the In-Space Technology Experiment Program (IN-STEP), which sponsors NASA, industry, and university flight experiments designed to enable and enhance space flight technology. The IN-STEP Program is sponsored by the Office of Space Access and Technology (OSAT).

  12. Smectite clays in Mars soil - Evidence for their presence and role in Viking biology experimental results

    NASA Technical Reports Server (NTRS)

    Banin, A.; Rishpon, J.

    1979-01-01

    Evidence for the presence of smectite clays in Martian soils is reviewed and results of experiments with certain active clays simulating the Viking biology experiments are reported. Analyses of Martian soil composition by means of X-ray fluorescence spectrometry and dust storm spectroscopy and Martian geological history strongly suggest the presence of a mixture of weathered ferro-silicate minerals, mainly nontronite and montmorillonite, accompanied by soluble sulphate salts, as major constituents. Samples of montmorillonite and nontronite incubated with (C-14)-formate or the radioactive nutrient medium solution used in the Viking Labeled Release experiment, were found to produce patterns of release of radioactive gas very similar to those observed in the Viking experiments, indicating the iron-catalyzed decomposition of formate as the reaction responsible for the Viking results. The experimental results of Hubbard (1979) simulating the results of the Viking Pyrolytic Release experiment using iron montmorillonites are pointed out, and it is concluded that many of the results of the Viking biology experiments can be explained in terms of the surface activity of smectite clays in catalysis and adsorption.

  13. Results of Experiments on Convective Precipitation Enhancement in the Camaguey Experimental Area, Cuba.

    NASA Astrophysics Data System (ADS)

    Koloskov, Boris; Zimin, Boris; Beliaev, Vitaly; Seregin, Yury; Chernikov, Albert; Petrov, Victor; Valdés, Mario; Martínez, Daniel; Pérez, Carlos A.; Puente, Guillermo

    1996-09-01

    Experiments on randomized seeding of individual convective clouds and cloud clusters were conducted in the Camaguey experimental area, Cuba, from 1985 through 1990 in order to elucidate whether cold-cloud dynamic seeding can be used to augment convective rainfall. An information measuring system was set up, and primary tools included three instrumented aircraft (AN-26, AN-12 CYCLONE, IL-14), MRL-5 and ARS-3 radars, a system for radiosounding, two special rain gauge networks, and surface weather stations.A total of 232 randomized experiments were carried out during this experimentation period, and 117 individual clouds and 115 cloud clusters were studied during 136 `go' days. Pyrotechnic flares containing silver iodide were ejected in a selected cloud when the seeder aircraft was flying through its top. The seeding effects were monitored by the MRL-5 radar, which was equipped with an automated system for digital processing of data.A total of 46 convective clouds, 29 seeded and 17 nonseeded, were studied during an exploratory experiment in 1985. Analyses of the radar properties of seeded and nonseeded clouds have indicated that the response of convective clouds to AgI seeding is dependent on their type, and the treatment within the range of cloud tops from 6 to 8 km—that is, at top temperatures between 10° and 20°C, is found to increase their maximum height by 13% and the lifetime by 30%, and to enhance rainfall.A confirmatory phase of the experiment in the Camaguey experimental area was conducted during 1986 90. A total of 46 individual convective clouds, 24 seeded and 22 nonseeded, were identified, and their properties were determined using three-dimensional radar data. The results have shown that the AgI seeding of growing clouds with top temperatures over the range from 10° to 20°C increases their lifetime by 24%, maximum height by 9%, area by 64%, and rain volume by 120%, as compared to unseeded clouds. The lifetime, area, and rainfall results are

  14. Experimental results of fingerprint comparison validity and reliability: A review and critical analysis.

    PubMed

    Haber, Ralph Norman; Haber, Lyn

    2014-09-01

    Our purpose in this article is to determine whether the results of the published experiments on the accuracy and reliability of fingerprint comparison can be generalized to fingerprint laboratory casework, and/or to document the error rate of the Analysis-Comparison-Evaluation (ACE) method. We review the existing 13 published experiments on fingerprint comparison accuracy and reliability. These studies comprise the entire corpus of experimental research published on the accuracy of fingerprint comparisons since criminal courts first admitted forensic fingerprint evidence about 120years ago. We start with the two studies by Ulery, Hicklin, Buscaglia and Roberts (2011, 2012), because they are recent, large, designed specifically to provide estimates of the accuracy and reliability of fingerprint comparisons, and to respond to the criticisms cited in the National Academy of Sciences Report (2009). Following the two Ulery et al. studies, we review and evaluate the other eleven experiments, considering problems that are unique to each. We then evaluate the 13 experiments for the problems common to all or most of them, especially with respect to the generalizability of their results to laboratory casework. Overall, we conclude that the experimental designs employed deviated from casework procedures in critical ways that preclude generalization of the results to casework. The experiments asked examiner-subjects to carry out their comparisons using different responses from those employed in casework; the experiments presented the comparisons in formats that differed from casework; the experiments enlisted highly trained examiners as experimental subjects rather than subjects drawn randomly from among all fingerprint examiners; the experiments did not use fingerprint test items known to be comparable in type and especially in difficulty to those encountered in casework; and the experiments did not require examiners to use the ACE method, nor was that method defined

  15. Implementation and experimental results of 4D tumor tracking using robotic couch

    PubMed Central

    Buzurovic, I.; Yu, Y.; Werner-Wasik, M.; Biswas, T.; Anne, P. R.; Dicker, A. P.; Podder, T. K.

    2012-01-01

    Purpose: This study presents the implementation and experimental results of a novel technique for 4D tumor tracking using a commercially available and commonly used treatment couch and evaluates the tumor tracking accuracy in clinical settings. Methods: Commercially available couch is capable of positioning the patient accurately; however, currently there is no provision for compensating physiological movement using the treatment couch in real-time. In this paper, a real-time couch tracking control technique is presented together with experimental results in tumor motion compensation in four dimensions (superior-inferior, lateral, anterior-posterior, and time). To implement real-time couch motion for tracking, a novel control system for the treatment couch was developed. The primary functional requirements for this novel technique were: (a) the treatment couch should maintain all previous/normal features for patient setup and positioning, (b) the new control system should be used as a parallel system when tumor tracking would be deployed, and (c) tracking could be performed in a single direction and/or concurrently in all three directions of the couch motion (longitudinal, lateral, and vertical). To the authors’ best knowledge, the implementation of such technique to a regular treatment couch for tumor tracking has not been reported so far. To evaluate the performance of the tracking couch, we investigated the mechanical characteristics of the system such as system positioning resolution, repeatability, accuracy, and tracking performance. Performance of the tracking system was evaluated using dosimetric test as an endpoint. To investigate the accuracy of real-time tracking in the clinical setting, the existing clinical treatment couch was replaced with our experimental couch and the linear accelerator was used to deliver 3D conformal radiation therapy (3D-CRT) and intensity modulated radiation therapy (IMRT) treatment plans with and without tracking. The results

  16. Indicated and actual mass inventory measurements for an inverted U-tube steam generator

    SciTech Connect

    Loomis, G.G.; Plessinger, M.P.; Boucher, T.J.

    1986-01-01

    Results from an experimental investigation of actual versus indicated secondary liquid level in a steam generator at steaming conditions are presented. The experimental investigation was performed in two different small scale U-tube-in-shell steam generators at typical pressurized water reactor operating conditions (5-7 MPa; saturated) in the Semiscale facility. During steaming conditions, the indicated secondary liquid level was found to vary considerably from the actual ''bottled-up'' liquid level. These difference between indicated and actual liquid level are related to the frictional pressure drop associated with the two-phase steaming condition in the riser. Data from a series of bottle-up experiments (Simultaneously, the primary heat source and secondary feed and steam are terminated) are tabulated and the actual liquid level is correlated to the indicated liquid level.

  17. Model On DROID Response With Imperfect Trapping Tested On Experimental Results

    NASA Astrophysics Data System (ADS)

    Hijmering, R. A.; Kozorezov, A. G.; Verhoeve, P.; Martin, D. D. E.; Wigmore, J. K.; Venn, R.

    2009-12-01

    The DROID (Distributed Read-Out Imaging Detector) is being developed to overcome the limitation in sensitive area with the use of single STJ's (Superconducting Tunnel Junctions). The DROID configuration allows the reconstruction of the position of the photon absorption and therefore it can replace a number of single STJ's in a detector array. We present a 2D model which describes the response of DROIDs with partial trapping in the STJs. The model describes diffusion of quasiparticles (qps) and imperfect confinement via exchange of qps between the absorber and STJ. It incorporates possible diffusion mismatch between absorber and STJ, possible asymmetry between the STJs as well as between the base and top electrodes of the STJs, and photon absorption in the absorber or base or top film of the STJ. Dedicated experiments have been conducted to test the different aspects of the model. We find a good agreement between the model and experimental results.

  18. Inlet Flow Test Calibration for a Small Axial Compressor Facility. Part 1: Design and Experimental Results

    NASA Technical Reports Server (NTRS)

    Miller, D. P.; Prahst, P. S.

    1994-01-01

    An axial compressor test rig has been designed for the operation of small turbomachines. The inlet region consisted of a long flowpath region with two series of support struts and a flapped inlet guide vane. A flow test was run to calibrate and determine the source and magnitudes of the loss mechanisms in the inlet for a highly loaded two-stage axial compressor test. Several flow conditions and IGV angle settings were established in which detailed surveys were completed. Boundary layer bleed was also provided along the casing of the inlet behind the support struts and ahead of the IGV. A detailed discussion of the flowpath design along with a summary of the experimental results are provided in Part 1.

  19. An aerodynamic analysis of the autogiro rotor with a comparison between calculated and experimental results

    NASA Technical Reports Server (NTRS)

    Wheatley, John B

    1935-01-01

    This report presents an extension of the autogiro theory of Glauert and Lock in which the influence of a pitch varying with the blade radius is evaluated and methods of approximating the effect of blade tip losses and the influence of reversed velocities on the retreating blades are developed. A comparison of calculated and experimental results showed that most of the rotor characteristics could be calculated with reasonable accuracy, and that the type of induced flow assumed has a secondary effect upon the net rotor forces, although the flapping motion is influenced appreciably. An approximate evaluation of the effect of parasite drag on the rotor blades established the importance of including this factor in the analysis.

  20. Some experimental results on the L-star instability of metallized composite propellants. [combustion instability

    NASA Technical Reports Server (NTRS)

    Kumar, R. N.

    1975-01-01

    Experimental results are reported on the L-star instability characteristics of three AP/composite propellants. The metal content of the propellants is 2, 16, and 16%. Chuffing, bulk mode oscillations, and time-independent combustion are observed with all three of these propellants. The stability boundary, defined as the boundary between time-independent and unstable combustion, is found to be well defined for two of the propellants in agreement with recognized trends available in the literature on other propellants. The frequency of bulk mode oscillations is presented as a function of the chamber characteristic length. One of the propellants tested has shown bulk mode instability at as high a pressure as 217 psia.

  1. Noise characteristics of upper surface blown configurations. Experimental program and results

    NASA Technical Reports Server (NTRS)

    Brown, W. H.; Searle, N.; Blakney, D. F.; Pennock, A. P.; Gibson, J. S.

    1977-01-01

    An experimental data base was developed from the model upper surface blowing (USB) propulsive lift system hardware. While the emphasis was on far field noise data, a considerable amount of relevant flow field data were also obtained. The data were derived from experiments in four different facilities resulting in: (1) small scale static flow field data; (2) small scale static noise data; (3) small scale simulated forward speed noise and load data; and (4) limited larger-scale static noise flow field and load data. All of the small scale tests used the same USB flap parts. Operational and geometrical variables covered in the test program included jet velocity, nozzle shape, nozzle area, nozzle impingement angle, nozzle vertical and horizontal location, flap length, flap deflection angle, and flap radius of curvature.

  2. Physical model and experimental results of cathode erosion related to power supply ripple

    NASA Technical Reports Server (NTRS)

    Harris, W. J.; O'Hair, E. A.; Hatfield, L. L.; Kristiansen, M.

    1992-01-01

    This paper discusses the physical effects of power supply ripple on cathode erosion and cathode arc attachment in a water-cooled, 30 kW nitrogen arcjet. Experimental results are presented for 2 percent thoriated tungsten, which show that the long-term cathode erosion rate is a decreasing function of current ripple over the range 1-13 percent. Above this range, the cathode discharge becomes unstable, and the erosion rate rapidly increases. A qualitative model of this effect is given in terms of a magnetically induced radial motion of the arc column, and an overall increase in the cathode spot radius due to the higher peak current associated with higher ripple. The most important effect of power supply ripple is therefore shown to be its ability to collectively drive the cathode attachment away from the cathode center. This leads to an increase in the cathode attachment area, and a subsequent decrease in the cathode erosion rate.

  3. Experimental results of active control on a large structure to suppress vibration

    NASA Technical Reports Server (NTRS)

    Dunn, H. J.

    1991-01-01

    Three design methods, Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR), H-infinity, and mu-synthesis, are used to obtain compensators for suppressing the vibrations of a 10-bay vertical truss structure, a component typical of what may be used to build a large space structure. For the design process the plant dynamic characteristics of the structure were determined experimentally using an identification method. The resulting compensators were implemented on a digital computer and tested for their ability to suppress the first bending mode response of the 10-bay vertical truss. Time histories of the measured motion are presented, and modal damping obtained during the experiments are compared with analytical predictions. The advantages and disadvantages of using the various design methods are discussed.

  4. Preliminary Results on the Experimental Investigation of the Structure Functions of Bound Nucleons

    SciTech Connect

    Bodek, Arie

    2015-09-01

    We present preliminary results on an experimental study of the nuclear modification of the longitudinal (σL) and transverse (σT) structure functions of nucleons bound in nuclear targets. The origin of these modifications (commonly referred as as the EMC effect) is not fully understood. Our measurements of R= σLT for nuclei (RA) and for deuterium (RD) indicate that nuclear modifications of the structure functions of bound nucleons are different for the longitudinal and transverse structure functions, and that contrary to expectation from several theoretical models, RA < RD.

  5. Simulation and experimental results of optical and thermal modeling of gold nanoshells.

    PubMed

    Ghazanfari, Lida; Khosroshahi, Mohammad E

    2014-09-01

    This paper proposes a generalized method for optical and thermal modeling of synthesized magneto-optical nanoshells (MNSs) for biomedical applications. Superparamagnetic magnetite nanoparticles with diameter of 9.5 ± 1.4 nm are fabricated using co-precipitation method and subsequently covered by a thin layer of gold to obtain 15.8 ± 3.5 nm MNSs. In this paper, simulations and detailed analysis are carried out for different nanoshell geometry to achieve a maximum heat power. Structural, magnetic and optical properties of MNSs are assessed using vibrating sample magnetometer (VSM), X-ray diffraction (XRD), UV-VIS spectrophotometer, dynamic light scattering (DLS), and transmission electron microscope (TEM). Magnetic saturation of synthesized magnetite nanoparticles are reduced from 46.94 to 11.98 emu/g after coating with gold. The performance of the proposed optical-thermal modeling technique is verified by simulation and experimental results. PMID:25063109

  6. Study of a vibrating plate: comparison between experimental (ESPI) and analytical results

    NASA Astrophysics Data System (ADS)

    Romero, G.; Alvarez, L.; Alanís, E.; Nallim, L.; Grossi, R.

    2003-07-01

    Real-time electronic speckle pattern interferometry (ESPI) was used for tuning and visualization of natural frequencies of a trapezoidal plate. The plate was excited to resonant vibration by a sinusoidal acoustical source, which provided a continuous range of audio frequencies. Fringe patterns produced during the time-average recording of the vibrating plate—corresponding to several resonant frequencies—were registered. From these interferograms, calculations of vibrational amplitudes by means of zero-order Bessel functions were performed in some particular cases. The system was also studied analytically. The analytical approach developed is based on the Rayleigh-Ritz method and on the use of non-orthogonal right triangular co-ordinates. The deflection of the plate is approximated by a set of beam characteristic orthogonal polynomials generated by using the Gram-Schmidt procedure. A high degree of correlation between computational analysis and experimental results was observed.

  7. Active vibration absorber for CSI evolutionary model: Design and experimental results

    NASA Technical Reports Server (NTRS)

    Bruner, Anne M.; Belvin, W. Keith; Horta, Lucas G.; Juang, Jer-Nan

    1991-01-01

    The development of control of large flexible structures technology must include practical demonstration to aid in the understanding and characterization of controlled structures in space. To support this effort, a testbed facility was developed to study practical implementation of new control technologies under realistic conditions. The design is discussed of a second order, acceleration feedback controller which acts as an active vibration absorber. This controller provides guaranteed stability margins for collocated sensor/actuator pairs in the absence of sensor/actuator dynamics and computational time delay. The primary performance objective considered is damping augmentation of the first nine structural modes. Comparison of experimental and predicted closed loop damping is presented, including test and simulation time histories for open and closed loop cases. Although the simulation and test results are not in full agreement, robustness of this design under model uncertainty is demonstrated. The basic advantage of this second order controller design is that the stability of the controller is model independent.

  8. Pore-pressure influence in the poroelastic behavior of rocks: Experimental studies and results

    SciTech Connect

    Laurent, J.; Bouteca, M.J.; Sarda, J.P.; Bary, D. )

    1993-06-01

    The influence of pore pressure on the elastic strain of rocks is basic to reservoir compaction and subsidence problems and in reservoir engineering and environment studies. Biot's coefficient is an important parameter used to determine the influence of pore pressure on rock deformation. This paper presents measurements of Biot's coefficient on limestone samples and interprets these measurements. The coefficients used in poroelastic studies first are defined as Biot's coefficient and compressibility coefficients proposed by Zimmerman. Then, the experimental apparatus and procedures used to measure these coefficients are described. Finally, the results, which confirm the theoretical framework of poroelasticity, are presented and discussed. The compressibility coefficients and Biot's coefficient increase with porosity according to a law that is formally similar to a Hashin-Shtrickman's type law. For porosities in the 4.5% to 23% range, Biot's coefficient increases from 0.34 to 0.83.

  9. Experimental and computer simulation results of the spot welding process using SORPAS software

    NASA Astrophysics Data System (ADS)

    Al-Jader, M. A.; Cullen, J. D.; Athi, N.; Al-Shamma'a, A. I.

    2009-07-01

    The highly competitive nature of the automotive industry drives demand for improvements and increased precision engineering in resistance spot welding. Currently there are about 4300 weld points on the average steel vehicle. Current industrial monitoring systems check the quality of the nugget after processing 15 cars, once every two weeks. The nuggets are examined off line using a destructive process, which takes approximately 10 days to complete causing a long delay in the production process. This paper presents a simulation of the spot welding growth curves, along with a comparison to growth curves performed on an industrial spot welding machine. The correlation of experimental results shows that SORPAS simulations can be used as an off line measurement to reduce factory energy usage. The first section in your paper

  10. Collision induced dissociation study of azobenzene and its derivatives: computational and experimental results

    NASA Astrophysics Data System (ADS)

    Rezaee, Mohammadreza; Compton, Robert

    2015-03-01

    Experimental and computational investigation have been performed in order to study the bond dissociation energy of azobenzene and its derivatives using collision induced dissociation method as well as other energy and structural characteristics. The results have been verified by comparing with results obtained from computational quantum chemistry. We used different density functional methods as well as the Möller-Plesset perturbation theory and the coupled cluster methods to explore geometric, electronic and the spectral properties of the sample molecules. Geometries were calculated and optimized using the 6-311 + + G(2d,2p) basis set and the B3LYP level of theory and these optimized structures have been subjected to the frequency calculations to obtain thermochemical properties by means of different density functional, Möller-Plesset, and coupled cluster theories to obtain a high accuracy estimation of the bond dissociation energy value. The results from experiments and the results obtained from computational thermochemistry are in close agreement. Physics and Astronomy Department

  11. Motion effects on an IFR hovering task: Analytical predictions and experimental results

    NASA Technical Reports Server (NTRS)

    Ringland, R. F.; Stapleford, R. L.; Magdaleno, R. E.

    1971-01-01

    An analytical pilot model incorporating the effects of motion cues and display scanning and sampling is tested by comparing predictions against experimental results on a moving base simulator. The simulated task is that of precision hovering of a VTOL having varying amounts of rate damping, and using separated instrument displays. Motion cue effects are investigated by running the experiment under fixed and moving base conditions, the latter in two modes; full motion, and angular motion only. Display scanning behavior is measured on some of the runs. The results of the program show that performance is best with angular motion only, most probably because a g-vector tilt cue is available to the pilot in this motion condition. This provides an attitude indication even when not visually fixating the attitude display. Vestibular threshold effects are also present in the results because of the display scaling used to permit hovering position control within the motion simulator limits; no washouts are used in the simulator drive signals. The IFR nature of the task results in large decrements in pilot opinion and performance relative to VFR conditions because of the scanning workload. Measurements of scanning behavior are sensitive to motion conditions and show more attention to attitude control under fixed base conditions.

  12. Preliminary experimental results on studying possibility of variable mass liner (VML) formation

    SciTech Connect

    1995-12-31

    The main objective of the present experiment was to study the formation process and initial stage of acceleration of a variable-mass plasma liner (VML). The method is based on magnetic acceleration of a liner with the mass reduced during such acceleration. The experiment was carried out on February 16 at VNIIEF. This report describes the results of measurements obtained in the experiment and preliminary analysis of the results characterizing operation of the test facility main units: helical EMG; 5-module disk EMG 400 mm in diameter (DEMG); ponderomotive unit (PU) with a cylindric condensed liner and a special tooth-cutoff. The first part of the report presents measurement results obtained on the VNIIEF`s diagnostic equipment that are compared with those obtained by American specialists on their diagnostic equipment. Information submitted by American specialists is included in part 2 of this report. The second part of the report presents preliminary computational-theoretic analysis of the main measured results describing operation of DEMG TL system in the experiment; experimental data are compared with theoretical ones obtained before and after the experiment. But more emphasis is placed on the data preliminary analysis indicating that in the experiment a variable mass liner is formed (VML or plasma bubble).

  13. Experimental results on the dissociation of molecular iodine in the presence of singlet oxygen molecules

    NASA Astrophysics Data System (ADS)

    Zagidullin, M. V.; Khvatov, N. A.; Malyshev, M. S.; Svistun, M. I.

    2016-08-01

    The experimental results on the dissociation of iodine molecules in the presence of single oxygen molecules under a widerange variation of the oxygen-iodine composition are presented. The rate constants are determined as 4.3 × 10-17 cm3 s-1 for the reaction O2(1Δ) + O2(1Δ) → O2(1Σ) + O2(3Σ) (reaction 1), 2.8 × 10-13 cm3 s-1 for the reaction O2(1Δ) + I(2P1/2) → O2(1Σ) + I(2P3/2) (4) and 8.3 × 10-11 cm3 s-1 for the reaction O2(1Σ) + I2 → O2(3Σ) + 2I (2). The analysis of the experimental results shows that for different compositions of the active medium of the oxygen-iodine laser the iodine dissociation occurs via the chain of reactions 1, 2, O2(1Δ) + I(2P3/2) → O2(3Σ) + I(2P1/2), 4 and in the cascade process I2 + I(2P1/2) → I2(u) + I(2P3/2), I2(u) + O2(1Δ) → 2I + O2(3Σ). For typical active medium compositions of the supersonic chemical oxygen-iodine laser, the contributions of each of the mechanisms to the dissociation are comparable. The experiments carried out did not reveal any contribution from the vibrationally excited oxygen molecules to the iodine dissociation. Thus, the performed experiments and the conclusions drawn from them completely confirm the mechanism of iodine dissociation, proposed earlier.

  14. Experimental results on the dissociation of molecular iodine in the presence of singlet oxygen molecules

    NASA Astrophysics Data System (ADS)

    Zagidullin, M. V.; Khvatov, N. A.; Malyshev, M. S.; Svistun, M. I.

    2016-08-01

    The experimental results on the dissociation of iodine molecules in the presence of single oxygen molecules under a widerange variation of the oxygen–iodine composition are presented. The rate constants are determined as 4.3 × 10-17 cm3 s-1 for the reaction O2(1Δ) + O2(1Δ) → O2(1Σ) + O2(3Σ) (reaction 1), 2.8 × 10-13 cm3 s-1 for the reaction O2(1Δ) + I(2P1/2) → O2(1Σ) + I(2P3/2) (4) and 8.3 × 10-11 cm3 s-1 for the reaction O2(1Σ) + I2 → O2(3Σ) + 2I (2). The analysis of the experimental results shows that for different compositions of the active medium of the oxygen–iodine laser the iodine dissociation occurs via the chain of reactions 1, 2, O2(1Δ) + I(2P3/2) → O2(3Σ) + I(2P1/2), 4 and in the cascade process I2 + I(2P1/2) → I2(u) + I(2P3/2), I2(u) + O2(1Δ) → 2I + O2(3Σ). For typical active medium compositions of the supersonic chemical oxygen–iodine laser, the contributions of each of the mechanisms to the dissociation are comparable. The experiments carried out did not reveal any contribution from the vibrationally excited oxygen molecules to the iodine dissociation. Thus, the performed experiments and the conclusions drawn from them completely confirm the mechanism of iodine dissociation, proposed earlier.

  15. Ultrafast solvation dynamics in water: Isotope effects and comparison with experimental results

    NASA Astrophysics Data System (ADS)

    Nandi, Nilashis; Roy, Srabani; Bagchi, Biman

    1995-01-01

    A detailed theoretical study of solvation dynamics in water is presented. The motivation of the present study comes from the recent experimental observation that the dynamics of solvation of an ion in water is ultrafast and the solvation time correlation function decays with a time constant of about 55 fs. The slower decay in the long time can be described by a sum of two exponentials with time constants equal to 126 and 880 fs. The molecular theory (developed earlier) predicts a time constant equal to 52 fs for the initial Gaussian decay and time constants equal to 134 and 886 fs for the two exponential components at the long time. This nearly perfect agreement is obtained by using the most detailed dynamical information available in the literature. The present study emphasizes the importance of the intermolecular vibrational band originating from the O...O stretching mode of the O-H...O units in the initial dynamics and raises several interesting questions regarding the nature of the decay of this mode. We have also studied the effects of isotope substitution on solvation dynamics. It is predicted that a significant isotope effect may be observed in the long time. The experimental results have also been compared with the prediction of the dynamic mean spherical approximation (DMSA); the agreement is not satisfactory at the long time. It is further found that the molecular theory and the DMSA lead to virtually identical results if the translational modes of the solvent molecules are neglected in the former. DMSA has also been used to investigate the dynamics of solvation of a dipolar solute in water. It is found that the dynamics of dipolar solvation exhibit features rather different from those of ion solvation.

  16. Theoretical versus experimental results for the rotordynamic coefficients of eccentric, smooth, gas annular seal annular gas seals

    NASA Technical Reports Server (NTRS)

    Childs, Dara W.; Alexander, Chis

    1994-01-01

    This viewgraph presentation presents the following results: (1) The analytical results overpredict the experimental results for the direct stiffness values and incorrectly predict increasing stiffness with decreasing pressure ratios. (2) Theory correctly predicts increasing cross-coupled stiffness, K(sub YX), with increasing eccentricity and inlet preswirl. (3) Direct damping, C(sub XX), underpredicts the experimental results, but the analytical results do correctly show that damping increases with increasing eccentricity. (4) The whirl frequency values predicted by theory are insensitive to changes in the static eccentricity ratio. Although these values match perfectly with the experimental results at 16,000 rpm, the results at the lower speed do not correspond. (5) Theoretical and experimental mass flow rates match at 5000 rpm, but at 16,000 rpm the theoretical results overpredict the experimental mass flow rates. (6) Theory correctly shows the linear pressure profiles and the associated entrance losses with the specified rotor positions.

  17. Shuttle Damage/Repair from the Perspective of Hypersonic Boundary Layer Transition - Experimental Results

    NASA Technical Reports Server (NTRS)

    Horvath, Thomas J.; Berry, Scott A.; Merski, N. Ronald; Berger, Karen T.; Buck, Gregory M.; Liechty, Derek S.; Schneider, Steven P.

    2006-01-01

    An overview is provided of the experimental wind tunnel program conducted at the NASA Langley Research Center Aerothermodynamics Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for Return-to-Flight. The effect of an isolated protuberance and an isolated rectangular cavity on hypersonic boundary layer transition onset on the windward surface of the Shuttle Orbiter has been experimentally characterized. These experimental studies were initiated to provide a protuberance and cavity effects database for developing hypersonic transition criteria to support on-orbit disposition of thermal protection system damage or repair. In addition, a synergistic experimental investigation was undertaken to assess the impact of an isolated mass-flow entrainment source (simulating pyrolysis/outgassing from a proposed tile repair material) on boundary layer transition. A brief review of the relevant literature regarding hypersonic boundary layer transition induced from cavities and localized mass addition from ablation is presented. Boundary layer transition results were obtained using 0.0075-scale Orbiter models with simulated tile damage (rectangular cavities) of varying length, width, and depth and simulated tile damage or repair (protuberances) of varying height. Cavity and mass addition effects were assessed at a fixed location (x/L = 0.3) along the model centerline in a region of near zero pressure gradient. Cavity length-to-depth ratio was systematically varied from 2.5 to 17.7 and length-to-width ratio of 1 to 8.5. Cavity depth-to-local boundary layer thickness ranged from 0.5 to 4.8. Protuberances were located at several sites along the centerline and port/starboard attachment lines along the chine and wing leading edge. Protuberance height-to-boundary layer thickness was varied from approximately 0.2 to 1.1. Global heat transfer images and heating distributions of the Orbiter windward surface using phosphor thermography were used to infer the

  18. [METHODOLOGICAL APPROACHES TO THE CALCULATION OF ACTUAL AND PREVENTED AS A RESULT OF CONTROL AND SUPERVISORY ACTIVITIES, MEDICAL-DEMOGRAPHIC AND ECONOMIC LOSSES, ASSOCIATED WITH THE NEGATIVE IMPACT OF ENVIRONMENTAL FACTORS].

    PubMed

    Popova, A Yu; Zaytseva, N V; May, I V; Kir'yanov, D A

    2015-01-01

    In the article there are reported the methodological approaches to the calculation of actual and avoided as a result of control and supervisory activities of economic losses caused by mortality, morbidity and disability in the population, associated with the negative impact of environmental factors. There is suggested a consistent solution of the chain of problems: the establishment of cause-and-effect relationships between indices of the health status and indices of the quality of the environment; indices of the quality of the environment and indices of the control and supervision activity of organs and institutions of Federal Service for Surveillance on Consumer Rights Protection and Human Wellbeing calculation of the cases of violations of health prevented as a result of the activity ofthe service; evaluation of their economic equivalents. Approbation of approaches on the example of the Russian Federation allowed to establish that as a result of the activity of organs and institutions of Federal Service for Surveillance on Consumer Rights Protection and Human Wellbeing in 2013, a positive trend was observed on 51 indices of quality of the habitat environment, there were prevented about 160 thousands of deaths and more than 2 million cases of disease that would be held in conditions of the lack of adequate control and surveillance measures in the field of sanitary and epidemiological welfare of the population. Loss prevention of gross domestic product (GDP) amounted to more than 120 billion rubles, Tax shortfalls in the federal budget--about 25.7 billion rubles. With taking into account the costs of the federal budgetfor the activities of the Federal Service for Surveillance on Consumer Rights Protection and Human Wellbeing in 2013 in part to ensure sanitary epidemiological surveillance in the amount of 11.386 billion rubles there was prevented loss of GDP of 10.56 rubles per 1 rub. of the cost of the federal budget and there was warned the shortfall of taxes to

  19. Comparison Between Numerical and Experimental Results on Mechanical Stirrer and Bubbling in a Cylindrical Tank - 13047

    SciTech Connect

    Lima da Silva, M.; Sauvage, E.; Brun, P.; Gagnoud, A.; Fautrelle, Y.; Riva, R.

    2013-07-01

    The process of vitrification in a cold crucible heated by direct induction is used in the fusion of oxides. Its feature is the production of high-purity materials. The high-level of purity of the molten is achieved because this melting technique excludes the contamination of the charge by the crucible. The aim of the present paper is to analyze the hydrodynamic of the vitrification process by direct induction, with the focus in the effects associated with the interaction between the mechanical stirrer and bubbling. Considering the complexity of the analyzed system and the goal of the present work, we simplified the system by not taking into account the thermal and electromagnetic phenomena. Based in the concept of hydraulic similitude, we performed an experimental study and a numerical modeling of the simplified model. The results of these two studies were compared and showed a good agreement. The results presented in this paper in conjunction with the previous work contribute to a better understanding of the hydrodynamics effects resulting from the interaction between the mechanical stirrer and air bubbling in the cold crucible heated by direct induction. Further works will take into account thermal and electromagnetic phenomena in the presence of mechanical stirrer and air bubbling. (authors)

  20. Optimal placement of piezoelectric plates for active vibration control of gas turbine blades: experimental results

    NASA Astrophysics Data System (ADS)

    Botta, F.; Marx, N.; Gentili, S.; Schwingshackl, C. W.; Di Mare, L.; Cerri, G.; Dini, D.

    2012-04-01

    It is well known that the gas turbine blade vibrations can give rise to catastrophic failures and a reduction of the blades life because of fatigue related phenomena[1]-[3] . In last two decades, the adoption of piezoelectric elements, has received considerable attention by many researcher for its potential applicability to different areas of mechanical, aerospace, aeronautical and civil engineering. Recently, a number of studies of blades vibration control via piezoelectric plates and patches have been reported[4]-[6] . It was reported that the use of piezoelectric elements can be very effective in actively controlling vibrations. In one of their previous contributions[7] , the authors of the present manuscript studied a model to control the blade vibrations by piezoelectric elements and validated their results using a multi-physics finite elements package (COMSOL) and results from the literature. An optimal placement method of piezoelectric plate has been developed and applied to different loading scenarios for realistic configurations encountered in gas turbine blades. It has been demonstrated that the optimal placement depends on the spectrum of the load, so that segmented piezoelectric patches have been considered and, for different loads, an optimal combination of sequential and/or parallel actuation and control of the segments has been studied. In this paper, an experimental investigation carried out by the authors using a simplified beam configuration is reported and discussed. The test results obtained by the investigators are then compared with the numerical predictions [7] .

  1. Initial Diagnostics and First Experimental Results of the Pulsed High Density (PHD) FRC Experiment*

    NASA Astrophysics Data System (ADS)

    Gota, Hiroshi

    2005-10-01

    The source region for the Pulsed High Density Experiment (PHDX) has been constructed, and Field-Reversed Configuration (FRC) plasmas are being produced. The several diagnostic systems include and axial array of 20 pairs of magnetic probes and flux loops, and a 64 channel array optical measurement system for visible bremstrahlung tomography. The tomographic system will be capable of reconstructing the plasma shape and mode structure, and will incorporate information from end-on imaging for improved resolution. This array consists of collimator, optical fiber, optical filter (λ=520 nm, FWHM= 1 to 10 nm), and Photomultiplier Tube (PMT). The tomographic system and magnetic loop array will be used to investigate the equilibrium and tilt stability of FRCs at high s/E (>3) where s is the ion collisionless skin depth and E is the plasma elongation. The separatrix radius (rs) of FRC plasma is determined by the excluded flux measurement, and it is found that rs=0.04-0.05 m (rs/rw=0.16-0.2) just after the RMF current drive start-up. The time sequence of separatrix shape relatively agrees with the result of that estimated from the line-integrated radiation intensity at different axial positions. We will present the result of both simulation and experimental results from measured FRC plasmas as well as future plans. *Research funded by the DOE Office of Fusion Energy Sciences

  2. A stereo triangulation system for structural identification: Analytical and experimental results

    NASA Technical Reports Server (NTRS)

    Junkins, J. L.; James, G. H., III; Pollock, T. C.; Rahman, Z. H.

    1988-01-01

    , and have established conclusively the feasibility and desirability of this approach. We discuss, in summary, recent advances in analog and digital video processing methodology, actuation methods, and bring them to bear on the structural identification problem. We include a brief discussion of our experimental hardware and some recent experimental results which support the practical feasibility of this structural vibration sensing approach.

  3. Responses of Tundra Ecosystems to Environmental Change: Observational and Experimental Results

    NASA Astrophysics Data System (ADS)

    Henry, G. H.

    2004-05-01

    Evidence of environmental changes due to human-enhanced climate warming continues to accumulate from polar regions. Responses in tundra and taiga ecosystems to climate changes have been variable because of the wide range in process response rates, from metabolic processes to adjustments in ecosystem carbon balance, and the variability in environmental settings across local to regional scales. For example, strong increases in rates of plant growth and changes in species composition and abundance have been observed in parts of the Low Arctic, but very little change has been measured in high arctic tundra. A dramatic increase in the cover of deciduous shrubs in areas of the western North American Arctic is predicted to result in positive feedbacks to soil temperature, through increased surface roughness and snow depth, and to atmospheric heating by reducing albedo. Increased shrub cover has also been found in long-term experimental warming studies conducted throughout the tundra biome as part of the International Tundra Experiment (ITEX). Warming is also affecting the carbon balance of tundra and taiga, which hold 25% of the soil carbon of global terrestrial ecosystems. However, trajectories of these changes are largely unknown for most northern systems, and differ because of initial conditions of the carbon and nutrient economy. Over the longer-term, the positive increases in plant growth may be constrained by negative feedbacks to nutrient cycling, as increases in C:N ratios of plant litter slow the release of nitrogen to soils. However, nitrogen availability has been shown to increase in response to short-term warming. In this presentation, I will review the responses of tundra ecosystems to climate variability and change, both through observational and experimental studies.

  4. Preliminary Experimental Results on the Technique of Artificial River Replenishment to Mitigate Sediment Loss Downstream Dams

    NASA Astrophysics Data System (ADS)

    Franca, M. J.; Battisacco, E.; Schleiss, A. J.

    2014-12-01

    The transport of sediments by water throughout the river basins, from the steep slopes of the upstream regions to the sea level, is recognizable important to keep the natural conditions of rivers with a role on their ecology processes. Over the last decades, a reduction on the supply of sand and gravel has been observed downstream dams existing in several alpine rivers. Many studies highlight that the presence of a dam strongly modifies the river behavior in the downstream reach, in terms of morphology and hydrodynamics, with consequences on local ecology. Sediment deficit, bed armoring, river incision and bank instability are the main effects which affect negatively the aquatic habitats and the water quality. One of the proposed techniques to solve the problem of sediment deficit downstream dams, already adopted in few Japanese and German rivers although on an unsatisfactory fashion, is the artificial replenishment of these. Generally, it was verified that the erosion of the replenishments was not satisfactory and the transport rate was not enough to move the sediments to sufficient downstream distances. In order to improve and to provide an engineering answer to make this technique more applicable, a series of laboratory tests are ran as preparatory study to understand the hydrodynamics of the river flow when the replenishment technique is applied. Erodible volumes, with different lengths and submergence conditions, reproducing sediment replenishments volumes, are positioned along a channel bank. Different geometrical combinations of erodible sediment volumes are tested as well on the experimental flume. The first results of the experimental research, concerning erosion time evolution, the influence of discharge and the distance travelled by the eroded sediments, will be presented and discussed.

  5. Synthesizing large-scale pyroclastic flows: Experimental design, scaling, and first results from PELE

    NASA Astrophysics Data System (ADS)

    Lube, G.; Breard, E. C. P.; Cronin, S. J.; Jones, J.

    2015-03-01

    Pyroclastic flow eruption large-scale experiment (PELE) is a large-scale facility for experimental studies of pyroclastic density currents (PDCs). It is used to generate high-energy currents involving 500-6500 m3 natural volcanic material and air that achieve velocities of 7-30 m s-1, flow thicknesses of 2-4.5 m, and runouts of >35 m. The experimental PDCs are synthesized by a controlled "eruption column collapse" of ash-lapilli suspensions onto an instrumented channel. The first set of experiments are documented here and used to elucidate the main flow regimes that influence PDC dynamic structure. Four phases are identified: (1) mixture acceleration during eruption column collapse, (2) column-slope impact, (3) PDC generation, and (4) ash cloud diffusion. The currents produced are fully turbulent flows and scale well to natural PDCs including small to large scales of turbulent transport. PELE is capable of generating short, pulsed, and sustained currents over periods of several tens of seconds, and dilute surge-like PDCs through to highly concentrated pyroclastic flow-like currents. The surge-like variants develop a basal <0.05 m thick regime of saltating/rolling particles and shifting sand waves, capped by a 2.5-4.5 m thick, turbulent suspension that grades upward to lower particle concentrations. Resulting deposits include stratified dunes, wavy and planar laminated beds, and thin ash cloud fall layers. Concentrated currents segregate into a dense basal underflow of <0.6 m thickness that remains aerated. This is capped by an upper ash cloud surge (1.5-3 m thick) with 100 to 10-4 vol % particles. Their deposits include stratified, massive, normally and reversely graded beds, lobate fronts, and laterally extensive veneer facies beyond channel margins.

  6. Beryllium metal I. experimental results on acute oral toxicity, local skin and eye effects, and genotoxicity.

    PubMed

    Strupp, Christian

    2011-01-01

    The toxicity of soluble metal compounds is often different from that of the parent metal. Since no reliable data on acute toxicity, local effects, and mutagenicity of beryllium metal have ever been generated, beryllium metal powder was tested according to the respective Organisation for Economical Co-Operation and Development (OECD) guidelines. Acute oral toxicity of beryllium metal was investigated in rats and local effects on skin and eye in rabbits. Skin-sensitizing properties were investigated in guinea pigs (maximization method). Basic knowledge about systemic bioavailability is important for the design of genotoxicity tests on poorly soluble substances. Therefore, it was necessary to experimentally compare the capacities of beryllium chloride and beryllium metal to form ions under simulated human lung conditions. Solubility of beryllium metal in artificial lung fluid was low, while solubility in artificial lysosomal fluid was moderate. Beryllium chloride dissolution kinetics were largely different, and thus, metal extracts were used in the in vitro genotoxicity tests. Genotoxicity was investigated in vitro in a bacterial reverse mutagenicity assay, a mammalian cell gene mutation assay, a mammalian cell chromosome aberration assay, and an unscheduled DNA synthesis (UDS) assay. In addition, cell transformation was tested in a Syrian hamster embryo cell assay, and potential inhibition of DNA repair was tested by modification of the UDS assay. Beryllium metal was found not to be mutagenic or clastogenic based on the experimental in vitro results. Furthermore, treatment with beryllium metal extracts did not induce DNA repair synthesis, indicative of no DNA-damaging potential of beryllium metal. A cell-transforming potential and a tendency to inhibit DNA repair when the cell is severely damaged by an external stimulus were observed. Beryllium metal was also found not to be a skin or eye irritant, not to be a skin sensitizer, and not to have relevant acute oral

  7. Beryllium Metal I. Experimental Results on Acute Oral Toxicity, Local Skin and Eye Effects, and Genotoxicity

    PubMed Central

    Strupp, Christian

    2011-01-01

    The toxicity of soluble metal compounds is often different from that of the parent metal. Since no reliable data on acute toxicity, local effects, and mutagenicity of beryllium metal have ever been generated, beryllium metal powder was tested according to the respective Organisation for Economical Co-Operation and Development (OECD) guidelines. Acute oral toxicity of beryllium metal was investigated in rats and local effects on skin and eye in rabbits. Skin-sensitizing properties were investigated in guinea pigs (maximization method). Basic knowledge about systemic bioavailability is important for the design of genotoxicity tests on poorly soluble substances. Therefore, it was necessary to experimentally compare the capacities of beryllium chloride and beryllium metal to form ions under simulated human lung conditions. Solubility of beryllium metal in artificial lung fluid was low, while solubility in artificial lysosomal fluid was moderate. Beryllium chloride dissolution kinetics were largely different, and thus, metal extracts were used in the in vitro genotoxicity tests. Genotoxicity was investigated in vitro in a bacterial reverse mutagenicity assay, a mammalian cell gene mutation assay, a mammalian cell chromosome aberration assay, and an unscheduled DNA synthesis (UDS) assay. In addition, cell transformation was tested in a Syrian hamster embryo cell assay, and potential inhibition of DNA repair was tested by modification of the UDS assay. Beryllium metal was found not to be mutagenic or clastogenic based on the experimental in vitro results. Furthermore, treatment with beryllium metal extracts did not induce DNA repair synthesis, indicative of no DNA-damaging potential of beryllium metal. A cell-transforming potential and a tendency to inhibit DNA repair when the cell is severely damaged by an external stimulus were observed. Beryllium metal was also found not to be a skin or eye irritant, not to be a skin sensitizer, and not to have relevant acute oral

  8. Soft material adhesion characterization for in vivo locomotion of robotic capsule endoscopes: Experimental and modeling results.

    PubMed

    Kern, Madalyn D; Ortega Alcaide, Joan; Rentschler, Mark E

    2014-11-01

    The objective of this work is to validate an experimental method and nondimensional model for characterizing the normal adhesive response between a polyvinyl chloride based synthetic biological tissue substrate and a flat, cylindrical probe with a smooth polydimethylsiloxane (PDMS) surface. The adhesion response is a critical mobility design parameter of a Robotic Capsule Endoscope (RCE) using PDMS treads to provide mobility to travel through the gastrointestinal tract for diagnostic purposes. Three RCE design characteristics were chosen as input parameters for the normal adhesion testing: pre-load, dwell time and separation rate. These parameters relate to the RCE׳s cross sectional dimension, tread length, and tread speed, respectively. An inscribed central composite design (CCD) prescribed 34 different parameter configurations to be tested. The experimental adhesion response curves were nondimensionalized by the maximum stress and total displacement values for each test configuration and a mean nondimensional curve was defined with a maximum relative error of 5.6%. A mathematical model describing the adhesion behavior as a function of the maximum stress and total displacement was developed and verified. A nonlinear regression analysis was done on the maximum stress and total displacement parameters and equations were defined as a function of the RCE design parameters. The nondimensional adhesion model is able to predict the adhesion curve response of any test configuration with a mean R(2) value of 0.995. Eight additional CCD studies were performed to obtain a qualitative understanding of the impact of tread contact area and synthetic material substrate stiffness on the adhesion response. These results suggest that the nondimensionalization technique for analyzing the adhesion data is sufficient for all values of probe radius and substrate stiffness within the bounds tested. This method can now be used for RCE tread design optimization given a set of

  9. Phase-space analysis and experimental results for secondary focusing at X-ray beamlines

    SciTech Connect

    Huang, Rong; Meron, Mati; Kujala, Naresh; Barrea, Raul A.

    2011-11-17

    Micro-focusing optical devices at synchrotron beamlines usually have a limited acceptance, but more flux can be intercepted if such optics are used to focus secondary sources created by the primary optics. Flux throughput can be maximized by placing the secondary focusing optics close to or exactly at the secondary source position. However, standard methods of beamline optics analysis, such as the lens equation or matching the mirror surface to an ellipse, work poorly when the source-to-optics distance is very short. In this paper the general characteristics of the focusing of beams with Gaussian profiles by a 'thin lens' are analysed under the paraxial approximation in phase space, concluding that the focusing of a beam with a short source-to-optics distance is distinct from imaging the source; slope errors are successfully included in all the formulas so that they can be used to calculate beamline focusing with good accuracy. A method is also introduced to use the thin-lens result to analyse the micro-focusing produced by an elliptically bent trapezoid-shaped Kirkpatrick-Baez mirror. The results of this analysis are in good agreement with ray-tracing simulations and are confirmed by the experimental results of the secondary focusing at the 18-ID Bio-CAT beamline (at the APS). The result of secondary focusing carried out at 18-ID using a single-bounce capillary can also be explained using this phase-space analysis. A discussion of the secondary focusing results is presented at the end of this paper.

  10. The Las Cruces Trench Site: Characterization, Experimental Results, and One-Dimensional Flow Predictions

    NASA Astrophysics Data System (ADS)

    Wierenga, P. J.; Hills, R. G.; Hudson, D. B.

    1991-10-01

    A comprehensive field trench study was conducted in a semiarid area of southern New Mexico to provide data to test deterministic and stochastic models of vadose zone flow and transport. A 4 m by 9 m area was irrigated with water containing a tracer using a carefully controlled drip irrigation system. The area was heavily instrumented with tensiometers and neutron probe access tubes to monitor water movement and with suction tubes to monitor solute transport. Approximately 600 disturbed and 600 core samples of soil were taken to support deterministic and stochastic characterization of the soil water hydraulic parameters. The core sample-based saturated hydraulic conductivities ranged from 1.4 to 6731 cm/d with a mean of 533 cm/d and a standard deviation of 647 cm/d, indicating significant spatial variability. However, visual observation of the wetting front on the trench wall shows no indication of preferential flow or water flow through visible root channels and cracks. The tensiometer readings and the neutron probe measurements also suggest that the wetting front moves in a fairly homogeneous fashion despite the significant spatial variability of the saturated hydraulic conductivity. In addition to the description of the experiment and the presentation of the experimental results, predictions of simple one-dimensional uniform and layered soil deterministic models for infiltration are presented and compared to field observations. These models are presented here to provide a base case against which more sophisticated deterministic and stochastic models can be compared in the future. The results indicate that the simple models give adequate predictions of the overall movement of the wetting front through the soil during infiltration. However, the models give poor predictions of point values for water content due to the spatial variability of the soil. Comparisons between the one-dimensional infiltration model predictions and field observations show that the use of

  11. Experimental demonstration of quantitation errors in MR spectroscopy resulting from saturation corrections under changing conditions

    NASA Astrophysics Data System (ADS)

    Galbán, Craig J.; Ellis, Scott J.; Spencer, Richard G. S.

    2003-04-01

    Metabolite concentration measurements in in vivo NMR are generally performed under partially saturated conditions, with correction for partial saturation performed after data collection using a measured saturation factor. Here, we present an experimental test of the hypothesis that quantitation errors can occur due to application of such saturation factor corrections in changing systems. Thus, this extends our previous theoretical work on quantitation errors due to varying saturation factors. We obtained results for two systems frequently studied by 31P NMR, the ischemic rat heart and the electrically stimulated rat gastrocnemius muscle. The results are interpreted in light of previous theoretical work which defined the degree of saturation occurring in a one-pulse experiment for a system with given spin-lattice relaxation times, T1s, equilibrium magnetizations, M0s, and reaction rates. We found that (i) the assumption of constancy of saturation factors leads to quantitation errors on the order of 40% in inorganic phosphate; (ii) the dominant contributor to the quantitation errors in inorganic phosphate is most likely changes in T1; (iii) T1 and M0 changes between control and intervention periods, and chemical exchange contribute to different extents to quantitation errors in phosphocreatine and γ-ATP; (iv) relatively small increases in interpulse delay substantially decreased quantitation errors for metabolites in ischemic rat hearts; (v) random error due to finite SNR led to approximately 4% error in quantitation, and hence was a substantially smaller contributor than were changes in saturation factors.

  12. Uranium speciation in moorland river water samples: a comparison of experimental results and computer model predictions.

    PubMed

    Unsworth, Emily R; Jones, Phil; Cook, Jennifer M; Hill, Steve J

    2005-06-01

    An on-line method has been developed for separating inorganic and organic bound uranium species present in river water samples. The method utilised a small chelating resin (Hyphan) column incorporated into the sample introduction manifold of an ICP-MS instrument. The method was evaluated for samples from rivers on Dartmoor (Devon, UK), an area of granite overlain with peat bogs. The results indicate that organic-uranium species form a major proportion (80%) of the total dissolved uranium present. Further work with synthetic water samples indicated that the level of dissolved organic carbon played a greater role in determining the level of organic-uranium species than did sample pH. Computer models for the water samples were constructed using the WHAM program (incorporating uranium data from the Nuclear Energy Agency Thermochemical Database project) in order to predict the levels of organic-uranium species that would form. By varying the proportion of humic and fulvic acids used in the humic component, predictions within 10% of the experimental results were obtained. The program did exhibit a low bias at higher pH values (7.5) and low organic carbon concentrations (0.5 microg ml(-1)), but under the natural conditions prevalent in the Dartmoor water samples, the model predictions were successful.

  13. Using the Viking biology experimental results to obtain chemical information about Martian regolith

    NASA Technical Reports Server (NTRS)

    Plumb, Robert C.

    1992-01-01

    Although initially formulated as biology experiments, most of the results produced by the Viking Labeled Release (LR), Gas Exchange (GEX), and Pyrolytic Release (PR) experiments have been reproduced by chemical means. The experiments do not need more study as 'biological' phenomena, but they do deserve much more careful consideration from a chemical viewpoint. They are the only 'wet-chemical' experiments that scientists have performed on another planet, but they have not found very general use as sources of scientific information. There is a large set of potentially useful chemical observations, e.g., the three resolvable and precisely measured kinetic components of the release of C-14-labeled gases, the thermal sensitivity and magnitudes of the oxidation reaction(s) of the LR experiments, the kinetics and magnitude of the O2 and CO2 release of the GEX experiments, the thermal sensitivity of the GEX results, the differences between the thermal sensitivity of the GEX and the thermal sensitivity of the LR responses, and the kinetics and magnitudes of the LR successive injection reabsorption effect. It should be possible to test many chemical aspects of hypothetical martian phenomena in experiments using the biology experimental configurations and derive much valuable information by comparisons with the Viking observations.

  14. Gas breakdown in the TCABR Tokamak: Model, simulation and experimental results

    NASA Astrophysics Data System (ADS)

    Fonseca, Antonio M. M.; da Silva, Ruy P.; Galvão, Ricardo M. O.; Kuznetzov, Yuri; Nascimento, I. C.; Sanada, Edson K.

    2001-04-01

    In this work, a study is presented on the hydrogen breakdown in the TCABR Tokamak. A breakdown model has been used that permitted the delimitation of the breakdown region in that machine. In the model, we considered the ionization and losses of charged particles. The losses considered were the drift due to the curvature and the gradient of the toroidal field, the existence of spurious fields and due to the delay of the electric field. Using the parameters of TCABR, four curves involving the electric toroidal field and the filling pressure were obtained. These curves defined the hydrogen breakdown area for the TCABR. The results obtained with the model were compared with the experimental results. It was verified that, for the TCABR, breakdown occurs for pressures ranging from 9.10-6 to 3.10-4 mbar and electric fields ranging from 2 to 10 V/m. The ratio electric field/pressure, in the breakdown region, varies from 3.107 to 5.108Vm-1 bar-1.

  15. Elasto- and electro-capillary instabilities of a nematic-isotropic interface: Experimental results.

    PubMed

    Oswald, P

    2010-09-01

    Recently, we have shown the existence of an electro-capillary instability of a nematic-isotropic interface stabilized by a temperature gradient (P. Oswald, EPL 90, 16005 (2010)). This instability results from a competition between the destabilizing action of the electric Maxwell stress and the stabilizing action of the thermal and capillary forces. The control parameters are the temperature gradient G , the applied voltage V and the thickness h of the nematic layer. In this paper, we present new experimental results on this instability in both the linear and nonlinear regimes. In particular, very rich phase diagrams are mapped out in the (h, V) plane for three different values of G . The divergence of the growth time close to the onset of instability is also studied in detail. In addition, we show the existence at low voltages of another instability of the de Gennes type, where the elastic Ericksen stress is responsible for the destabilization. In this case, a hill-and-valley structure or a square array of umbilics develop at the interface depending on the values of h , V and G . PMID:20924636

  16. Experimental Results for Temporally Overlapping Pulses from Quantel EverGreen 200 Laser

    NASA Technical Reports Server (NTRS)

    Watkins, A. Neal

    2013-01-01

    This report will detail the experimental results and observations obtained while investigating the feasibility of temporally overlapping the two laser pulses from a Quantel EverGreen 200 Laser. This laser was specifically designed for Particle Imaging Velocimetry (PIV) applications and operate by emitting two 532 nm laser pulses that are seperated by an adjustable finite time (typically on the order of ten to hundreds of microseconds). However, the use of this model laser has found recent application for Pressure Sensitive Paint (PSP) testing, especially for rotorcraft research. For this testing, it is desired to only use one laser pulse. While this is easily done by only firing one of the laser heads, more excitation energy could conceivably be had if both laser heads are fired with zero pulse separation. In addition, recently large field-of-view PIV measurements have become possible and need ever increasing laser power to illuminate the larger areas. For this work, two different methods of timing the laser are investigated using both a traditional power meter to monitor laser power as well as a fast photodiode to determine pulse separation. The results are presented here as well as some simple implications for PIV experiments using these methods.

  17. [Acoustic and optical perceptual disorders in depressive diseases--an overview of results from experimental studies].

    PubMed

    Kallert, T W

    1996-01-01

    This literature review concentrates on a disregarded part of depressive disorders' symptomatology (especially concerning present-day classifications of mental disorders) that can be approached with a great number of experimental procedures. From the acoustical field the following findings are demonstrated and discussed: elevated click thresholds in auditory signal detection, changed ear asymmetry in dichotic click detection and differences in dichotic listening asymmetries according to symptomatology. The most important results from the so far investigated optical perceptual disturbances in depressive disorders are: breakdown of perceptual defence in the form of greater access to emotionally unpleasant stimuli referring to the tachistoscopic recognition of neutral/unpleasant words, impairments at near-distance assessments, disturbances in recognition and discrimination of facial emotions-especially concerning the perception of emotional chimeric faces. Interpretational attempts for these acoustical and optical disturbances of perception reach from developmental psychology to biological psychiatry. Changes in hemisphere functions hold the dominating position in this discussion. Up to now it remains open to what extent the reported results correlate with the clinical phenomenology of depressive disorders, of what diagnostic specifity they are and if the can be viewed with sufficient reliability as state marker and indicators for theraopeutical effects.

  18. Quantitative Assessment of the CCMC's Experimental Real-time SWMF-Geospace Results

    NASA Astrophysics Data System (ADS)

    Liemohn, Michael; Ganushkina, Natalia; De Zeeuw, Darren; Welling, Daniel; Toth, Gabor; Ilie, Raluca; Gombosi, Tamas; van der Holst, Bart; Kuznetsova, Maria; Maddox, Marlo; Rastaetter, Lutz

    2016-04-01

    Experimental real-time simulations of the Space Weather Modeling Framework (SWMF) are conducted at the Community Coordinated Modeling Center (CCMC), with results available there (http://ccmc.gsfc.nasa.gov/realtime.php), through the CCMC Integrated Space Weather Analysis (iSWA) site (http://iswa.ccmc.gsfc.nasa.gov/IswaSystemWebApp/), and the Michigan SWMF site (http://csem.engin.umich.edu/realtime). Presently, two configurations of the SWMF are running in real time at CCMC, both focusing on the geospace modules, using the BATS-R-US magnetohydrodynamic model, the Ridley Ionosphere Model, and with and without the Rice Convection Model for inner magnetospheric drift physics. While both have been running for several years, nearly continuous results are available since July 2015. Dst from the model output is compared against the Kyoto real-time Dst, in particular the daily minimum value of Dst to quantify the ability of the model to capture storms. Contingency tables are presented, showing that the run with the inner magnetosphere model is much better at reproducing storm-time values. For disturbances with a minimum Dst lower than -50 nT, this version yields a probability of event detection of 0.86 and a Heidke Skill Score of 0.60. In the other version of the SWMF, without the inner magnetospheric module included, the modeled Dst never dropped below -50 nT during the examined epoch.

  19. Secondary emission from dust grains with a surface layer: comparison between experimental and model results

    NASA Astrophysics Data System (ADS)

    Richterová, I.; Pavlů, J.; Němeček, Z.; Šafránková, J.; Žilavý, P.

    2006-01-01

    The motion, coalescence, and other processes in dust clouds are determined by the dust charge. Since dust grains in the space are bombarded by energetic electrons, the secondary emission is an important process contributing to their charge. It is generally expected that the secondary emission yield is related to surface properties of the bombarded body. However, it is well known that secondary emission from small bodies is determined not only by their composition but an effect of dimension can be very important when the penetration depth of primary electrons is comparable with the grain size. It implies that the secondary emission yield can be influenced by the substrate material if the surface layer is thin enough. We have developed a simple Monte Carlo model of secondary emission that was successfully applied on the dust stimulants from glass and melamine formaldehyde (MF) resin and matched very well experimental results. In order to check the influence of surface layers, we have modified the model for spheres covered by a layer with different material properties. The results of model simulations are compared with measurements on MF spheres covered by a nickel layer.

  20. Synthesis of Experimental and Model Results From The Esquif Project Over The Paris Area

    NASA Astrophysics Data System (ADS)

    Menut, L.; Esquif Team

    The ESQUIF research project follows mainly two goals: (i) To built a complete database of observations related to pollutants as all other parameters linked to the origin of this regional Paris area pollution, (ii) To improve our knowledge on regional atmospheric pollution events, focusing on the Paris area ("Ile de France", a zone of 150x150km, centered on the Paris city). The experimental part of the project (1998- 2000) is now over and the database freely available. The project now turns to improve and validate existing models dedicated to pollution analysis, scenarii and forecasting. From the whole set of studied topics, we will focus on some results: 1. The importance of the local "Paris area" emissions on the photochemical pollution, compared to long-range transport of polluted air mass, for which the source may be external to the studied area. A contrario the impact of parisian sources on the neigh- bouring areas and the potential extent of this influence (study of the parisian "plume"). 2. The sensitivity of photooxidant concentrations to the meteorology (local and synop- tic) and to emissions of primary pollutants by the way of modelling: it includes direct, adjoint and Monte-Carlo methodologies. 3. Some preliminary results on urban aerosols, estimated from numerous measure- ments during summer 2000. It includes the radiative impact of aerosols and cloudiness on photooxidant pollution. 4. A coupled approach, using chemistry-transport model and aircraft data, is presented for surface emissions optimization.

  1. A comparison of experimental results of soot production in laminar premixed flames

    NASA Astrophysics Data System (ADS)

    Caetano, Nattan R.; Soares, Diego; Nunes, Roger P.; Pereira, Fernando M.; Smith Schneider, Paulo; Vielmo, Horácio A.; van der Laan, Flávio Tadeu

    2015-05-01

    Soot emission has been the focus of numerous studies due to the numerous applications in industry, as well as the harmful effects caused to the environment. Thus, the purpose of this work is to analyze the soot formation in a flat flame burner using premixed compressed natural gas and air, where these quasi-adiabatic flames have one-dimensional characteristics. The measurements were performed applying the light extinction technique. The air/fuel equivalence ratiowas varied to assess the soot volume fractions for different flame configurations. Soot production along the flamewas also analyzed by measurements at different heights in relation to the burner surface. Results indicate that soot volume fraction increases with the equivalence ratio. The higher regions of the flamewere analyzed in order to map the soot distribution on these flames. The results are incorporated into the experimental database for measurement techniques calibration and for computational models validation of soot formation in methane premixed laminar flames, where the equivalence ratio ranging from 1.5 up to 8.

  2. Preliminary experimental results of tungsten wire-array Z-pinches on primary test stand

    SciTech Connect

    Huang, Xian-Bin; Zhou, Shao-Tong; Dan, Jia-Kun; Ren, Xiao-Dong Wang, Kun-Lun; Zhang, Si-Qun; Li, Jing; Xu, Qiang; Cai, Hong-Chun; Duan, Shu-Chao; Ouyang, Kai; Chen, Guang-Hua; Ji, Ce; Wei, Bing; Feng, Shu-Ping; Wang, Meng; Xie, Wei-Ping; Deng, Jian-Jun; Zhou, Xiu-Wen; Yang, Yi

    2015-07-15

    The Primary Test Stand (PTS) developed at the China Academy of Engineering Physics is a 20 TW pulsed power driver, which can deliver a ∼10 MA, 70 ns rise-time (10%–90%) current to a short-circuit load and has important applications in Z-pinch driven inertial confinement fusion and high energy density physics. Preliminary results of tungsten wire-array Z-pinch experiments on PTS are presented. The load geometries investigated include 15-mm-tall cylindrical single and nested arrays with diameter ranging from 13 mm to 30 mm, consisting of 132–300 tungsten wires with 5–10 μm in diameter. Multiple diagnostics were fielded to characterize the x-ray radiation from wire-array Z pinches. The x-ray peak power (∼50 TW) and total radiated energy (∼500 kJ) were obtained from a single 20-mm-diam array with 80-ns stagnation time. The highest x-ray peak power up to 80 TW with 2.4 ns FWHM was achieved by using a nested array with 20-mm outer diameter, and the total x-ray energy from the nested array is comparable to that of single array. Implosion velocity estimated from the time-resolved image measurement exceeds 30 cm/μs. The detailed experimental results and other findings are presented and discussed.

  3. Thermodiffusion in concentrated ferrofluids: Experimental and numerical results on magnetic thermodiffusion

    SciTech Connect

    Sprenger, Lisa Lange, Adrian; Odenbach, Stefan

    2014-02-15

    Ferrofluids consist of magnetic nanoparticles dispersed in a carrier liquid. Their strong thermodiffusive behaviour, characterised by the Soret coefficient, coupled with the dependency of the fluid's parameters on magnetic fields is dealt with in this work. It is known from former experimental investigations on the one hand that the Soret coefficient itself is magnetic field dependent and on the other hand that the accuracy of the coefficient's experimental determination highly depends on the volume concentration of the fluid. The thermally driven separation of particles and carrier liquid is carried out with a concentrated ferrofluid (φ = 0.087) in a horizontal thermodiffusion cell and is compared to equally detected former measurement data. The temperature gradient (1 K/mm) is applied perpendicular to the separation layer. The magnetic field is either applied parallel or perpendicular to the temperature difference. For three different magnetic field strengths (40 kA/m, 100 kA/m, 320 kA/m) the diffusive separation is detected. It reveals a sign change of the Soret coefficient with rising field strength for both field directions which stands for a change in the direction of motion of the particles. This behaviour contradicts former experimental results with a dilute magnetic fluid, in which a change in the coefficient's sign could only be detected for the parallel setup. An anisotropic behaviour in the current data is measured referring to the intensity of the separation being more intense in the perpendicular position of the magnetic field: S{sub T‖} = −0.152 K{sup −1} and S{sub T⊥} = −0.257 K{sup −1} at H = 320 kA/m. The ferrofluiddynamics-theory (FFD-theory) describes the thermodiffusive processes thermodynamically and a numerical simulation of the fluid's separation depending on the two transport parameters ξ{sub ‖} and ξ{sub ⊥} used within the FFD-theory can be implemented. In the case of a parallel aligned magnetic field, the parameter can

  4. COMPARISON OF EXPERIMENTAL RESULTS TO CFD MODELS FOR BLENDING IN A TANK USING DUAL OPPOSING JETS

    SciTech Connect

    Leishear, R.

    2011-08-07

    Research has been completed in a pilot scale, eight foot diameter tank to investigate blending, using a pump with dual opposing jets. The jets re-circulate fluids in the tank to promote blending when fluids are added to the tank. Different jet diameters and different horizontal and vertical orientations of the jets were investigated. In all, eighty five tests were performed both in a tank without internal obstructions and a tank with vertical obstructions similar to a tube bank in a heat exchanger. These obstructions provided scale models of several miles of two inch diameter, serpentine, vertical cooling coils below the liquid surface for a full scale, 1.3 million gallon, liquid radioactive waste storage tank. Two types of tests were performed. One type of test used a tracer fluid, which was homogeneously blended into solution. Data were statistically evaluated to determine blending times for solutions of different density and viscosity, and the blending times were successfully compared to computational fluid dynamics (CFD) models. The other type of test blended solutions of different viscosity. For example, in one test a half tank of water was added to a half tank of a more viscous, concentrated salt solution. In this case, the fluid mechanics of the blending process was noted to significantly change due to stratification of fluids. CFD models for stratification were not investigated. This paper is the fourth in a series of papers resulting from this research (Leishear, et.al. [1- 4]), and this paper documents final test results, statistical analysis of the data, a comparison of experimental results to CFD models, and scale-up of the results to a full scale tank.

  5. Modal characterization of the ASCIE segmented optics testbed: New algorithms and experimental results

    NASA Technical Reports Server (NTRS)

    Carrier, Alain C.; Aubrun, Jean-Noel

    1993-01-01

    New frequency response measurement procedures, on-line modal tuning techniques, and off-line modal identification algorithms are developed and applied to the modal identification of the Advanced Structures/Controls Integrated Experiment (ASCIE), a generic segmented optics telescope test-bed representative of future complex space structures. The frequency response measurement procedure uses all the actuators simultaneously to excite the structure and all the sensors to measure the structural response so that all the transfer functions are measured simultaneously. Structural responses to sinusoidal excitations are measured and analyzed to calculate spectral responses. The spectral responses in turn are analyzed as the spectral data become available and, which is new, the results are used to maintain high quality measurements. Data acquisition, processing, and checking procedures are fully automated. As the acquisition of the frequency response progresses, an on-line algorithm keeps track of the actuator force distribution that maximizes the structural response to automatically tune to a structural mode when approaching a resonant frequency. This tuning is insensitive to delays, ill-conditioning, and nonproportional damping. Experimental results show that is useful for modal surveys even in high modal density regions. For thorough modeling, a constructive procedure is proposed to identify the dynamics of a complex system from its frequency response with the minimization of a least-squares cost function as a desirable objective. This procedure relies on off-line modal separation algorithms to extract modal information and on least-squares parameter subset optimization to combine the modal results and globally fit the modal parameters to the measured data. The modal separation algorithms resolved modal density of 5 modes/Hz in the ASCIE experiment. They promise to be useful in many challenging applications.

  6. Cessation of environmentally-assisted cracking in a low-alloy steel: Experimental results

    SciTech Connect

    Li, Y.Y.

    1997-01-01

    The presence of dissolved metallurgical sulfides in pressure vessel and piping steels has been linked to Environmentally-Assisted Cracking (EAC), a phenomenon observed in laboratory tests that results in fatigue crack growth rates as high as 100 times that in air. Previous experimental and analytical work based on diffusion as the mass transport process has shown that surface cracks that are initially clean of sulfides will not initiate EAC in most applications. This is because the average crack tip velocity would not be sufficiently high to expose enough metallurgical sulfides per unit time and produce the sulfide concentration required for EAC. However, there is a potential concern for the case of a relatively large embedded crack breaking through to the wetted surface. Such a crack would not be initially clean of sulfides, and EAC could initiate. This paper presents the results of a series of experiments conducted on two heats of an EAC susceptible, high-sulfur, low-alloy steel in 243{degrees}C low-oxygen water to further study the phenomenon of EAC persistence at low crack tip velocities. A load cycle profile that incorporated a significant load dwell period at minimum load was used. In one experiment, the fatigue cycling history was such that relatively high crack tip velocities at the start of the experiment produced a persistent case of EAC even when crack tip velocities were later reduced to levels below the EAC initiation velocity. The other series of experiments used initial crack tip velocities that were much lower and probably more realistic. Air precracking of the compact tension specimens produced an initial inventory of undissolved sulfides on the crack flanks that directly simulates the array of sulfides expected from the breakthrough of an embedded crack. In all cases, results showed EAC ceased after several hundred hours of cycling.

  7. Experimental Results from the Thermal Energy Storage-2 (TES-2) Flight Experiment

    NASA Technical Reports Server (NTRS)

    Tolbert, Carol

    2000-01-01

    Thermal Energy Storage-2 (TES-2) is a flight experiment that flew on the Space Shuttle Endeavour (STS-72), in January 1996. TES-2 originally flew with TES-1 as part of the OAST-2 Hitchhiker payload on the Space Shuttle Columbia (STS-62) in early 1994. The two experiments, TES-1 and TES-2 were identical except for the fluoride salts to be characterized. TES-1 provided data on lithium fluoride (LiF), TES-2 provided data on a fluoride eutectic (LiF/CaF2). Each experiment was a complex autonomous payload in a Get-Away-Special payload canister. TES-1 operated flawlessly for 22 hr. Results were reported in a paper entitled, Effect of Microgravity on Materials Undergoing Melting and Freezing-The TES Experiment, by David Namkoong et al. A software failure in TES-2 caused its shutdown after 4 sec of operation. TES-1 and 2 were the first experiments in a four experiment suite designed to provide data for understanding the long duration microgravity behavior of thermal energy storage salts that undergo repeated melting and freezing. Such data have never been obtained before and have direct application for the development of space-based solar dynamic (SD) power systems. These power systems will store energy in a thermal energy salt such as lithium fluoride or a eutectic of lithium fluoride/calcium difluoride. The stored energy is extracted during the shade portion of the orbit. This enables the solar dynamic power system to provide constant electrical power over the entire orbit. Analytical computer codes were developed for predicting performance of a space-based solar dynamic power system. Experimental verification of the analytical predictions were needed prior to using the analytical results for future space power design applications. The four TES flight experiments were to be used to obtain the needed experimental data. This paper will address the flight results from the first and second experiments, TES-1 and 2, in comparison to the predicted results from the Thermal

  8. First Experimental Results Using Sparse Aperture Mask for Low Order Wavefront Sensing

    NASA Astrophysics Data System (ADS)

    Subedi, Hari; Zimmerman, Neil T.; Kasdin, N. Jeremy; Eldorado Riggs, A. J.

    2016-01-01

    We can determine the existence of life outside of earth by analyzing the spectra of exoplanets. Such direct imaging will provide the capability to thoroughly characterize an exoplanet's atmosphere. Direct imaging of exoplanets, however, has many technical challenges and difficulties: scattering and diffraction of light and the large difference in contrast, which is the ratio of brightness between the bright star and the dimmer planet. A coronagraph is an optical device that manipulates the diffraction of starlight and creates a region of high contrast (dark hole) where the dimmer planets can be seen. While in principle the level of contrast required for direct imaging of exoplanets can be achieved by stellar coronagraphic imaging, the resulting dark hole is highly sensitive to phase aberrations. In order to effectively suppress starlight for exoplanet imaging applications, low-order wavefront aberrations entering a coronagraph such as tip-tilt, defocus and coma must be determined and compensated for. A sparse-aperture mask (SAM) can be integrated in the telescopic imaging system to make precise estimate of low-order wavefront aberrations. In this technique, the starlight rejected by the coronagraph's focal plane stop is collimated to a relay pupil, where the mask forms an interference fringe pattern on a detector and the phase aberrations are inferred from this fringe pattern. At Princeton's High Contrast Imaging Lab (HCIL), we have numerically proved this concept and we are currently working on verifying it experimentally.

  9. Experimental Results From Stitched Composite Multi-Bay Fuselage Panels Tested Under Uni-Axial Compression

    NASA Technical Reports Server (NTRS)

    Baker, Donald J.

    2004-01-01

    The experimental results from two stitched VARTM composite panels tested under uni-axial compression loading are presented. The curved panels are divided by frames and stringers into five or six bays with a column of three bays along the compressive loading direction. The frames are supported at the ends to resist out-of-plane translation. Back-to-back strain gages are used to record the strain and displacement transducers were used to record the out-of-plane displacements. In addition a full-field measurement technique that utilizes a camera-based-stero-vision system was used to record displacements. The panels were loaded in increments to determine the first bay to buckle. Loading was discontinued at limit load and the panels were removed from the test machine for impact testing. After impacting at 20 ft-lbs to 25 ft-lbs of energy with a spherical indenter, the panels were loaded in compression until failure. Impact testing reduced the axial stiffness 4 percent and less than 1 percent. Postbuckled axial panel stiffness was 52 percent and 70 percent of the pre-buckled stiffness.

  10. Colloid filtration in surface dense vegetation: experimental results and theoretical predictions.

    PubMed

    Wu, Lei; Muñoz-Carpena, Rafael; Gao, Bin; Yang, Wen; Pachepsky, Yakov A

    2014-04-01

    Understanding colloid and colloid-facilitated contaminant transport in overland flow through dense vegetation is important to protect water quality in the environment, especially for water bodies receiving agricultural and urban runoff. In previous studies, a single-stem efficiency theory for rigid and clean stem systems was developed to predict colloid filtration by plant stems of vegetation in laminar overland flow. Hence, in order to improve the accuracy of the single-stem efficiency theory to real dense vegetation system, we incorporated the effect of natural organic matter (NOM) on the filtration of colloids by stems. Laboratory dense vegetation flow chamber experiments and model simulations were used to determine the kinetic deposition (filtration) rate of colloids under various conditions. The results show that, in addition to flow hydrodynamics and solution chemistry, steric repulsion afforded by NOM layer on the plants stem surface also plays a significant role in controlling colloid deposition on vegetation in overland flow. For the first time, a refined single-stem efficiency theory with considerations of the NOM effect is developed that describes the experimental data with good accuracy. This theory can be used to not only help construct and refine mathematical models of colloid transport in real vegetation systems in overland flow, but also inform the development of theories of colloid deposition on NOM-coated surfaces in natural, engineered, and biomedical systems.

  11. The dependence of ultrasonic backscatter on trabecular thickness in human calcaneus: theoretical and experimental results.

    PubMed

    Wear, Keith A; Laib, Andres

    2003-08-01

    Trabecular thickness within cancellous bone is an important determinant of osteoporotic fracture risk. Noninvasive assessment of trabecular thickness potentially could yield useful diagnostic information. Faran's theory of elastic scattering from a cylindrical object immersed in a fluid has been used to predict the dependence of ultrasonic backscatter on trabecular thickness. The theory predicts that, in the range of morphological and material properties expected for trabecular bone, the backscatter coefficient at 500 kHz should be approximately proportional to trabecular thickness to the power of 2.9. Experimental measurements of backscatter coefficient were performed on 43 human calcaneus samples in vitro. Mean trabecular thicknesses on the 43 samples were assessed using micro computed tomography (CT). A power law fit to the data showed that the backscatter coefficient empirically varied as trabecular thickness to the 2.8 power. The 95% confidence interval for this exponent was 1.7 to 3.9. The square of the correlation coefficient for the linear regression to the log transformed data was 0.40. This suggests that 40% of variations in backscatter may be attributed to variations in trabecular thickness. These results reinforce previous studies that offered validation for the Faran cylinder model for prediction of scattering properties of cancellous bone, and provide added evidence for the potential diagnostic utility of the backscatter measurement. PMID:12952089

  12. Development, calibration and experimental results obtained with an innovative calorimeter (CALMOS) for nuclear heating measurements

    SciTech Connect

    Carcreff, H.; Cloute-Cazalaa, V.; Salmon, L.

    2011-07-01

    Nuclear heating inside an MTR reactor has to be known in order to be able to control samples temperature during irradiation experiments. An R and D program has been carried out at CEA to design a new type of in-core calorimetric system. This new development, started in 2002, has for main objective to manufacture a calorimeter suitable to monitoring nuclear heating inside the 70 MWth OSIRIS material testing reactor operated by CEA's Nuclear Energy Div. at the Saclay research center. An innovative calorimetric probe, associated to a specific handling system, has been designed to provide access to measurements both along the fissile height and on the upper part of the core, where nuclear heating still remains high. Two mock-ups of the probe were manufactured and tested in 2005 and 2009 in ex-core area of OSIRIS reactor for process validation, while a displacement system has been especially studied to move the probe along a given axial measurement range. This paper deals with the development, tests on preliminary mock-ups and the finalization of the probe. Main modeling and experimental results are presented. Moreover, alternative methods to calibration for nuclear heating rate measurements which are now possible with this new calorimeter are presented and discussed. (authors)

  13. Development, calibration, and experimental results obtained with an innovative calorimeter (CALMOS) for nuclear heating measurements

    SciTech Connect

    Carcreff, Hubert; Cloute-Cazalaa, Veronique; Salmon, Laurent

    2012-08-15

    Nuclear heating inside an MTR reactor has to be known in order to be able to control samples temperature during irradiation experiments. An R and D program has been carried out at CEA to design a new type of in-core calorimetric system. This new development, started in 2002, has for main objective to manufacture a calorimeter suitable to monitoring nuclear heating inside the 70 MWth OSIRIS material testing reactor operated by CEA's Nuclear Energy Division at the Saclay research center. An innovative calorimetric probe, associated to a specific handling system, has been designed to provide access to measurements both along the fissile height and on the upper part of the core, where nuclear heating still remains high. Two mock-ups of the probe were manufactured and tested in 2005 and 2009 in ex-core area of OSIRIS reactor for process validation, while a displacement system has been especially studied to move the probe along a given axial measurement range. This paper deals with the development, tests on preliminary mock-ups and the finalization of the probe. Main modeling and experimental results are presented. Moreover, alternative methods to calibration for nuclear heating rate measurements which are now possible with this new calorimeter are presented and discussed. (authors)

  14. Active behavior of abdominal wall muscles: Experimental results and numerical model formulation.

    PubMed

    Grasa, J; Sierra, M; Lauzeral, N; Muñoz, M J; Miana-Mena, F J; Calvo, B

    2016-08-01

    In the present study a computational finite element technique is proposed to simulate the mechanical response of muscles in the abdominal wall. This technique considers the active behavior of the tissue taking into account both collagen and muscle fiber directions. In an attempt to obtain the computational response as close as possible to real muscles, the parameters needed to adjust the mathematical formulation were determined from in vitro experimental tests. Experiments were conducted on male New Zealand White rabbits (2047±34g) and the active properties of three different muscles: Rectus Abdominis, External Oblique and multi-layered samples formed by three muscles (External Oblique, Internal Oblique, and Transversus Abdominis) were characterized. The parameters obtained for each muscle were incorporated into a finite strain formulation to simulate active behavior of muscles incorporating the anisotropy of the tissue. The results show the potential of the model to predict the anisotropic behavior of the tissue associated to fibers and how this influences on the strain, stress and generated force during an isometric contraction. PMID:27111629

  15. Colloid filtration in surface dense vegetation: experimental results and theoretical predictions.

    PubMed

    Wu, Lei; Muñoz-Carpena, Rafael; Gao, Bin; Yang, Wen; Pachepsky, Yakov A

    2014-04-01

    Understanding colloid and colloid-facilitated contaminant transport in overland flow through dense vegetation is important to protect water quality in the environment, especially for water bodies receiving agricultural and urban runoff. In previous studies, a single-stem efficiency theory for rigid and clean stem systems was developed to predict colloid filtration by plant stems of vegetation in laminar overland flow. Hence, in order to improve the accuracy of the single-stem efficiency theory to real dense vegetation system, we incorporated the effect of natural organic matter (NOM) on the filtration of colloids by stems. Laboratory dense vegetation flow chamber experiments and model simulations were used to determine the kinetic deposition (filtration) rate of colloids under various conditions. The results show that, in addition to flow hydrodynamics and solution chemistry, steric repulsion afforded by NOM layer on the plants stem surface also plays a significant role in controlling colloid deposition on vegetation in overland flow. For the first time, a refined single-stem efficiency theory with considerations of the NOM effect is developed that describes the experimental data with good accuracy. This theory can be used to not only help construct and refine mathematical models of colloid transport in real vegetation systems in overland flow, but also inform the development of theories of colloid deposition on NOM-coated surfaces in natural, engineered, and biomedical systems. PMID:24597773

  16. Experimental Results of High Pressure and High Strain Rate Tantalum Flow Stress on Omega and NIF

    NASA Astrophysics Data System (ADS)

    Park, Hye-Sook; Arsenlis, A.; Barton, N.; Benedetti, L.; Huntington, C.; McNaney, J.; Orlikowski, D.; Prisbrey, S.; Remington, B.; Rudd, R.; Swift, D.; Weber, S.; Wehrenberg, C.; Comley, A.

    2015-11-01

    Understanding the high pressure, high strain rate plastic deformation dynamics of materials is an area of research of high interest to planetary formation dynamics, meteor impact dynamics, and inertial confinement fusion designs. Developing predictive theoretical and computational descriptions of such systems, however, has been a difficult undertaking. We have performed many experiments on Omega, LCLS and NIF to test Ta strength models at high pressures (~ up to 4 Mbar), high strain rates (~ 107 s-1) and high strains (>30%) under ramped compression conditions using Rayleigh-Taylor and Richtmyer-Meshkov instability properties. These experiments use plasma drive to ramp compress the sample to higher pressure without shock-melting. We also studied lattice level strength mechanisms under shocked compression using a diffraction-based technique. Our studies show that the strength mechanisms from macro to micro scales are different from the traditional strength model predictions and that they are loading path dependent. We will report the experimental results. Work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under contract DE-AC52-07NA273.

  17. Experimental Results of Site Calibration and Sensitivity Measurements in OTR for UWB Systems

    NASA Astrophysics Data System (ADS)

    Viswanadham, Chandana; Rao, P. Mallikrajuna

    2016-08-01

    System calibration and parameter accuracy measurement of electronic support measures (ESM) systems is a major activity, carried out by electronic warfare (EW) engineers. These activities are very critical and needs good understanding in the field of microwaves, antennas, wave propagation, digital and communication domains. EW systems are broad band, built with state-of-the art electronic hardware, installed on different varieties of military platforms to guard country's security from time to time. EW systems operate in wide frequency ranges, typically in the order of thousands of MHz, hence these are ultra wide band (UWB) systems. Few calibration activities are carried within the system and in the test sites, to meet the accuracies of final specifications. After calibration, parameters are measured for their accuracies either in feed mode by injecting the RF signals into the front end or in radiation mode by transmitting the RF signals on to system antenna. To carry out these activities in radiation mode, a calibrated open test range (OTR) is necessary in the frequency band of interest. Thus site calibration of OTR is necessary to be carried out before taking up system calibration and parameter measurements. This paper presents the experimental results of OTR site calibration and sensitivity measurements of UWB systems in radiation mode.

  18. Control of vibrations for a parallel manipulator with flexible links — concepts and experimental results

    NASA Astrophysics Data System (ADS)

    Morlock, M.; Burkhardt, M.; Seifried, R.

    2016-09-01

    A comprehensive control approach is presented to reduce the vibrations of a parallel manipulator with a kinematic loop and two flexible links whereof the longer one can show significant oscillations. The control objectives are end-effector trajectory tracking and active vibration control. The system is modeled as a flexible multibody system and exact feedforward control based on the full dynamic flexible multibody system is applied to improve the end-effector trajectory tracking performance. Furthermore, the effect of different position control concepts for the two linear drives, such as gain scheduling for the utilized cascade control and a model based friction compensation, on the movers themselves as well as on the end-effector are discussed, which can be conflicting. Experimental results are presented illustrating the achievable accuracy of the end-effector tracking for different trajectories while showing significant error reductions for a feedforward control based on an elastic model in contrast to a rigid one. Finally, a model based curvature controller is utilized which actively controls the occurring oscillations of the parallel manipulator. Here, a proportional controller as well as a linear-quadratic regulator are applied and the impact of an additional curvature control on the end-effector tracking performance is investigated.

  19. Diffusion and defect reactions between donors, C, and vacancies in Ge. I. Experimental results

    NASA Astrophysics Data System (ADS)

    Brotzmann, S.; Bracht, H.; Hansen, J. Lundsgaard; Larsen, A. Nylandsted; Simoen, E.; Haller, E. E.; Christensen, J. S.; Werner, P.

    2008-06-01

    The diffusion of self-atoms and n -type dopants such as phosphorus, arsenic, and antimony in germanium was studied by means of isotopically controlled multilayer structures doped with carbon. The diffusion profiles reveal an aggregation of the dopants within the carbon-doped layers and a retarded penetration depth compared to dopant diffusion in high-purity natural Ge. Dopant aggregation and diffusion retardation are strongest for Sb and similar for P and As. In addition, the shape of the dopant profiles changes for dopant concentrations in the range of 1020cm-3 mainly due to the formation of dopant-vacancy complexes, which is more significant at high concentrations. Accurate modeling of the simultaneous self-diffusion and dopant diffusion is achieved on the basis of the vacancy mechanism and additional reactions that take into account the formation of neutral carbon-vacancy-dopant and neutral dopant-vacancy complexes. The stability of these complexes is compared to theoretical calculations published recently and to additional calculations presented in Part II. The overall consistency between the experimental and theoretical results supports the stabilization of donor-vacancy complexes in Ge by the presence of carbon and the dopant deactivation via the formation of dopant-vacancy and carbon-vacancy-dopant complexes.

  20. Non-Shock Initiation Model for Plastic Bonded Explosive PBXN-5 and Cast Explosive: Experimental Results

    NASA Astrophysics Data System (ADS)

    Anderson, Mark; Todd, Steven; Caipen, Terry; Jensen, Charlie; Hughs, Chance

    2009-06-01

    A damage initiated reaction (DMGIR) computational model is being developed for the CTH shock physics code to predict the response of an explosive to non-shock mechanical insults. The distinguishing feature of this model is the introduction of a damage variable, which relates the evolution of damage to the initiation of reaction in the explosive, and its growth to detonation. The DMGIR model is a complement to the History Variable Reactive Burn (HVRB) model embedded in the current CTH code. Specifically designed experiments are supporting the development, implementation, and validation of the DMGIR numerical approach. PBXN-5 was the initial explosive material used experimentally to develop the DMGIR model. This explosive represents a family of plastically bonded explosives with good mechanical strength and rigid body properties. The model has been extended to cast explosives represented by Composition B. Furthermore, the DMGIR model will extended to predict results of non-shock mechanical insults for moldable plastic explosives such as C4 and PrimaSheet.

  1. Optimal piezoelectric beam shape for single and broadband vibration energy harvesting: Modeling, simulation and experimental results

    NASA Astrophysics Data System (ADS)

    Muthalif, Asan G. A.; Nordin, N. H. Diyana

    2015-03-01

    Harvesting energy from the surroundings has become a new trend in saving our environment. Among the established ones are solar panels, wind turbines and hydroelectric generators which have successfully grown in meeting the world's energy demand. However, for low powered electronic devices; especially when being placed in a remote area, micro scale energy harvesting is preferable. One of the popular methods is via vibration energy scavenging which converts mechanical energy (from vibration) to electrical energy by the effect of coupling between mechanical variables and electric or magnetic fields. As the voltage generated greatly depends on the geometry and size of the piezoelectric material, there is a need to define an optimum shape and configuration of the piezoelectric energy scavenger. In this research, mathematical derivations for unimorph piezoelectric energy harvester are presented. Simulation is done using MATLAB and COMSOL Multiphysics software to study the effect of varying the length and shape of the beam to the generated voltage. Experimental results comparing triangular and rectangular shaped piezoelectric beam are also presented.

  2. Active behavior of abdominal wall muscles: Experimental results and numerical model formulation.

    PubMed

    Grasa, J; Sierra, M; Lauzeral, N; Muñoz, M J; Miana-Mena, F J; Calvo, B

    2016-08-01

    In the present study a computational finite element technique is proposed to simulate the mechanical response of muscles in the abdominal wall. This technique considers the active behavior of the tissue taking into account both collagen and muscle fiber directions. In an attempt to obtain the computational response as close as possible to real muscles, the parameters needed to adjust the mathematical formulation were determined from in vitro experimental tests. Experiments were conducted on male New Zealand White rabbits (2047±34g) and the active properties of three different muscles: Rectus Abdominis, External Oblique and multi-layered samples formed by three muscles (External Oblique, Internal Oblique, and Transversus Abdominis) were characterized. The parameters obtained for each muscle were incorporated into a finite strain formulation to simulate active behavior of muscles incorporating the anisotropy of the tissue. The results show the potential of the model to predict the anisotropic behavior of the tissue associated to fibers and how this influences on the strain, stress and generated force during an isometric contraction.

  3. Two-dimensional discrete element models of debris avalanches: Parameterization and the reproducibility of experimental results

    NASA Astrophysics Data System (ADS)

    Banton, J.; Villard, P.; Jongmans, D.; Scavia, C.

    2009-11-01

    Application of the discrete element method (DEM) to model avalanches of granular materials requires determining the correct geometric and rheological parameters for and between the particles as well as for the basal surface. The use of spherical (circular in 2-D) particles enhances particle rolling, yielding excessive runout values. The solution usually adopted to correct this effect is to introduce a drag force which artificially slows down the particle velocities. The aim of this study is to test the capability of the DEM to simulate well-controlled unsteady channelized granular flows, considering the measured properties of the particles and of the basal surface which naturally contribute to dissipate energy. We first performed a parametrical analysis on a simple 2-D model in order to estimate the influence of particle shape, friction parameters, and restitution coefficients on the dynamics of the flow and on the deposit geometry. We then simulated three channelized laboratory experiments performed with two materials and two bed linings. Using the geometrical layout and the values of the mechanical parameters provided by the authors, we obtained a remarkable agreement between the observed and 2-D simulated deposit shapes for the three experiments. Also, the computed mass evolution with time was very consistent with the experimental snapshots in all cases. These results highlight the capability of the DEM technique for modeling avalanche of granular material when the particle shape as well as the friction and restitution coefficients are properly considered.

  4. Experimental results obtained with the positron-annihilation- radiation telescope of the Toulouse-Argonne collaboration

    SciTech Connect

    Naya, J.E.; von Ballmoos, P.; Albernhe, F.; Vedrenne, G.; Smither, R.K.; Faiz, M.; Fernandez, P.B.; Graber, T.

    1995-10-01

    We present laboratory measurements obtained with a ground-based prototype of a focusing positron-annihilation-radiation telescope developed by the Toulouse-Argonne collaboration. This balloon-borne telescope has been designed to collect 511-keV photons with an extremely low instrumental background. The telescope features a Laue diffraction lens and a detector module containing a small array of germanium detectors. It will provide a combination of high spatial and energy resolution (15 arc sec and 2 keV, respectively) with a sensitivity of {approximately}3{times}10{sup {minus}5} photons cm{sup {minus}2}s{sup {minus}1}. These features will allow us to resolve a possible narrow 511-keV line both energetically and spatially within a Galactic center ``microquasar`` or in other broad-class annihilators. The ground-based prototype consists of a crystal lens holding small cubes of diffracting germanium crystals and a 3{times}3 germanium array that detects the concentrated beam in the focal plane. Measured performances of the instrument at different line energies (511 keV and 662 keV) are presented and compared with Monte-Carlo simulations. The advantages of a 3{times}3 Ge-detector array with respect to a standard-monoblock detector have been confirmed. The results obtained in the laboratory have strengthened interest in a crystal-diffraction telescope, offering new perspectives for die future of experimental gamma-ray astronomy.

  5. MHD activity in the ISX-B tokamak: experimental results and theoretical interpretation

    SciTech Connect

    Carreras, B.A.; Dunlap, J.L.; Bell, J.D.; Charlton, L.A.; Cooper, W.A.; Dory, R.A.; Hender, T.C.; Hicks, H.R.; Holmes, J.A.; Lynch, V.E.

    1982-01-01

    The observed spectrum of MHD fluctuations in the ISX-B tokamak is clearly dominated by the n=1 mode when the q=1 surface is in the plasma. This fact agrees well with theoretical predictions based on 3-D resistive MHD calculations. They show that the (m=1; n=1) mode is then the dominant instability. It drives other n=1 modes through toroidal coupling and n>1 modes through nonlinear couplings. These theoretically predicted mode structures have been compared in detail with the experimentally measured wave forms (using arrays of soft x-ray detectors). The agreement is excellent. More detailed comparisons between theory and experiment have required careful reconstructions of the ISX-B equilibria. The equilibria so constructed have permitted a precise evaluation of the ideal MHD stability properties of ISX-B. The present results indicate that the high ..beta.. ISX-B equilibria are marginally stable to finite eta ideal MHD modes. The resistive MHD calculations also show that at finite ..beta.. there are unstable resistive pressure driven modes.

  6. Experimental results performed in the framework of the HIPER European Project

    NASA Astrophysics Data System (ADS)

    Batani, D.; Koenig, M.; Baton, S.; Perez, F.; Gizzi, L. A.; Koester, P.; Labate, L.; Honrubia, J.; Debayle, A.; Santos, J.; Schurtz, G.; Hulin, S.; Ribeyre, X.; Fourment, C.; Nicolai, P.; Vauzour, B.; Gremillet, L.; Nazarov, W.; Pasley, J.; Tallents, G.; Richetta, M.; Lancaster, K.; Spindloe, Ch.; Tolley, M.; Neely, D.; Norreys, P.; Kozlova, M.; Nejdl, J.; Rus, B.; Antonelli, L.; Morace, A.; Volpe, L.,; Davies, J.; Wolowski, J.; Badziak, J.

    2011-06-01

    This paper presents the goals and some of the results of experiments conducted within the Working Package 10 (Fusion Experimental Programme) of the HiPER Project. These experiments concern the study of the physics connected to "Advanced Ignition Schemes", i.e. the Fast Ignition and the Shock Ignition Approaches to Inertial Fusion. Such schemes are aimed at achieving a higher gain, as compared to the classical approach which is used in NIF, as required for future reactors, and making fusion possible with smaller facilities. In particular, a series of experiments related to Fast Ignition were performed at the RAL (UK) and LULI, France) Laboratories and were addressed to study the propagation of fast electrons (created by a short-pulse ultra-high-intensity beam) in compressed matter, created either by cylindrical implosions or by compression of planar targets by (planar) laser-driven shock waves. A more recent experiment was performed at PALS and investigated the laser-plasma coupling in the 1016 W/cm2 intensity regime of interest for Shock Ignition.

  7. Design and experimental results for a compact laser printer optical system with MEMS scanning mirror

    NASA Astrophysics Data System (ADS)

    Suzuki, Takatoshi; Seki, Daisuke; Fujii, Shuichi; Mukai, Yukihiro

    2010-02-01

    There are many features expected by printer users, which include high resolution, low price, compact size, color, high speed printing and so on. Laser printers generally utilize a polygon mirror as a reflector in their optical configurations, but the usual size of the polygon mirror prevents laser scanning unit from being made much smaller. We have been conducting research on techniques which can contribute to reducing the optical unit size. Although oscillating mirror made with MEMS technology enables the system to be compact, it requires a sophisticated optical design having an increased number of constraints due to the change in angular velocity which varies depending on the orientation of the mirror, while the polygon mirror allows the scanning with constant speed. Using a small MEMS mirror is one of the critical issues concerning the reduction of cost. We have successfully resolved all the challenges listed above by using high-precision free-form optical surfaces and an optical layout making efficient use of 3D space. Our techniques can make the unit size much smaller and reduce the price. The optical path is designed to have a ray passing through a lens twice. We report both theoretical and experimental results for this system.

  8. A new mechanical device for circular compression anastomosis. Preliminary results of animal and clinical experimentation.

    PubMed Central

    Rosati, R; Rebuffat, C; Pezzuoli, G

    1988-01-01

    The authors report the preliminary results obtained in animal and clinical experimentation of a new mechanical device for circular anastomosis which they have developed. It is a gun that places an apparatus consisting of three polypropylene rings that, through the compression among them of the severed edges of the bowel, realize a sutureless anastomosis and are spontaneously evacuated. Fifty-eight colonic anastomoses were performed in dogs with this device; 23 stapled colonic anastomoses were also executed concurrently. Forty-four animals underwent a relaparotomy to remove the colonic specimen containing the anastomoses. Bursting pressure and the histologic features of the anastomoses were evaluated at different time intervals after operation. A good healing of all compression anastomoses was observed, thereby allowing them to initiate the experience in humans. Thirteen anastomoses (6 colorectal extraperitoneal, 1 colorectal intraperitoneal, 5 colocolonic, 1 ileorectal) were performed at the 1st Surgical Department, Milan University. One subclinical leakage (7.7%) spontaneously healed in a few days. No stenoses were observed. Images Fig. 1. Fig. 2., Fig. 4., Fig. 6. Fig. 3., Fig. 5., Fig. 7. Fig. 8. Fig. 9. PMID:3345111

  9. CZT detectors used in different irradiation geometries: Simulations and experimental results

    SciTech Connect

    Fritz, Shannon G.; Shikhaliev, Polad M.

    2009-04-15

    The purpose of this work was to evaluate potential advantages and limitations of CZT detectors used in surface-on, edge-on, and tilted angle irradiation geometries. Simulations and experimental investigations of the energy spectrum measured by a CZT detector have been performed using different irradiation geometries of the CZT. Experiments were performed using a CZT detector with 10x10 mm{sup 2} size and 3 mm thickness. The detector was irradiated with collimated photon beams from Am-241 (59.5 keV) and Co-57 (122 keV). The edge-scan method was used to measure the detector response function in edge-on illumination mode. The tilted angle mode was investigated with the radiation beam directed to the detector surface at angles of 90 degree sign , 15 degree sign , and 10 degree sign . The Hecht formalism was used to simulate theoretical energy spectra. The parameters used for simulations were matched to experiment to compare experimental and theoretical results. The tilted angle CZT detector suppressed the tailing of the spectrum and provided an increase in peak-to-total ratio from 38% at 90 degree sign to 83% at 10 degree sign tilt angle for 122 keV radiation. The corresponding increase for 59 keV radiation was from 60% at 90 degree sign to 85% at 10 degree sign tilt angle. The edge-on CZT detector provided high energy resolution when the beam thickness was much smaller than the thickness of CZT. The FWHM resolution in edge-on illumination mode was 4.2% for 122 keV beam with 0.3 mm thickness, and rapidly deteriorated when the thickness of the beam was increased. The energy resolution of surface-on geometry suffered from strong tailing effect at photon energies higher than 60 keV. It is concluded that tilted angle CZT provides high energy resolution but it is limited to a 1D linear array configuration. The surface-on CZT provides 2D pixel arrays but suffers from tailing effect and charge build up. The edge-on CZT is considered suboptimal as it requires small beam

  10. Wageningen Urban Rainfall Experiment 2014 (WURex14): Experimental Setup and First Results

    NASA Astrophysics Data System (ADS)

    Uijlenhoet, R.; Overeem, A.; Leijnse, H.; Hazenberg, P.

    2014-12-01

    the atmosphere. Approximately halfway along the link path a rain gauge from the KNMI operational network is located. Finally, data is available from several commercial microwave links in the vicinity of the experimental setup, as well as from the KNMI weather radars. We report on the first results from this experiment, collected during the Summer and Fall of 2014.

  11. A comparison of experimental and theoretical results for rotordynamic coefficients of four annular gas seals

    NASA Technical Reports Server (NTRS)

    Childs, D. W.; Nelson, C. C.; Elrod, D.; Nicks, C.

    1985-01-01

    The test facility and initial test program developed to experimentally measure the fluid forces induced by annular gas seals is described. A comparison of theoretically predicted and experimentally obtained data for smooth and honeycomb seals is provided. And a comparison of experimental data from the tests of three smooth-rotor/smooth-stator seals is provided. The leakage of the working fluid through the seal, the pressure gradient along the seal length, entrance pressure-loss data, and rotordynamic coefficients provide a basis for comparison. A short discussion on seal theory is included, and various rotordynamic coefficient identification schemes are described.

  12. NASA/Pratt and Whitney experimental clean combustor program: Engine test results

    NASA Technical Reports Server (NTRS)

    Roberts, R.; Fiorentino, A. J.; Greene, W.

    1977-01-01

    A two-stage vorbix (vortex burning and mixing) combustor and associated fuel system components were successfully tested in an experimental JT9D engine at steady-state and transient operating conditions, using ASTM Jet-A fuel. Full-scale JT9D experimental engine tests were conducted in a phase three aircraft experimental clean combustor program. The low-pollution combustor, fuel system, and fuel control concepts were derived from phase one and phase two programs in which several combustor concepts were evaluated, refined, and optimized in a component test rig. Significant pollution reductions were achieved with the combustor which meets the performance, operating, and installation requirements of the engine.

  13. Nitrogen-broadened lineshapes in the oxygen A-band: Experimental results and theoretical calculations

    NASA Astrophysics Data System (ADS)

    Predoi-Cross, Adriana; Holladay, Christopher; Heung, Henry; Bouanich, Jean-Pierre; Mellau, Georg Ch.; Keller, Reimund; Hurtmans, Daniel R.

    2008-09-01

    We report measurements for N 2-broadening, pressure-shift and line mixing coefficients for 55 oxygen transitions in the A-band retrieved using a multispectrum fitting technique. Nineteen laboratory absorption spectra were recorded at 0.02 cm -1 resolution using a multi-pass absorption cell with path length of 1636.9 cm and the IFS 120 Fourier transform spectrometer located at Justus-Liebig-University in Giessen, Germany. The total sample pressures ranged from 8.8 to 3004.5 Torr with oxygen volume mixing ratios in nitrogen ranging between 0.057 and 0.62. An Exponential Power Gap (EPG) scaling law was used to calculate the N 2-broadening and N 2-line mixing coefficients. The line broadening and shift coefficients for the A-band of oxygen self-perturbed and perturbed by N 2 are modeled using semiclassical calculations based on the Robert-Bonamy formalism and two intermolecular potentials. These potentials involve electrostatic contributions including the hexadecapole moment of the molecules and (a) a simple dispersion contribution with one adjustable parameter to fit the broadening coefficients or (b) the atom-atom Lennard-Jones model without such adjustable parameters. The first potential leads to very weak broadening coefficients for high J transitions whereas the second potential gives much more improved results at medium and large J values, in reasonable agreement with the experimental data. For the line shifts which mainly arise in our calculation from the electronic state dependence of the isotropic potential, their general trends with increasing J values can be well predicted, especially from the first potential. From the theoretical results, we have derived air-broadening and air-induced shift coefficients with an agreement comparable to that obtained for O 2-O 2 and O 2-N 2.

  14. First Experimental Results from the EU 2 MW Coaxial Cavity Iter Gyrotron Prototype

    NASA Astrophysics Data System (ADS)

    Goodman, T. P.; Alberti, S.; Droz, E.; Fasel, D.; Hogge, J. P.; Jawla, S.; Porte, L.; Siravo, U.; Tran, M. Q.; Albajar, F.; Bonicelli, T.; Benin, P.; Bethuys, S.; Lievin, C.; Cirant, S.; Dumbrajs, O.; Gantenbein, G.; Illy, S.; Jin, J.; Kern, S.; Piosczyk, B.; Rzesnicki, T.; Thumm, M.

    2009-04-01

    The EU is working towards providing 2 MW, coaxial-cavity, CW, 170 GHz gyrotrons for ITER. Their design is based on results from an experimental pre-prototype tube in operation at FZK for several years, having a pulse length of several milliseconds. The first industrial prototype tube is designed for CW operation, but, in a first phase, will be tested out to 1s at the European Gyrotron Test Facility in Lausanne, Switzerland as part of a phased testing/development program (1 s, 60 s, CW). It is known that RF beam profile shaping, stray radiation handling, and collector cooling at these high power levels are three issues for the gyrotron, The gyrotron, magnet and body power supply have been delivered and successfully installed at the test stand, hosted by the CRPP. The main high voltage power supply delivery is delayed, so one of the power supplies dedicated to 3 of 9 gyrotrons in the TCV EC system is being used as a backup power source (all 3 TCV power sources can be interfaced with the test stand). Cathode conditioning began in November 2007 followed by collector conditioning in December. Parasitic low frequency oscillations have not hindered operation, and the tests have progressed to conditioning out to 0.14 s pulses by March 2008. During this period, the perfomance concerning microwave generation has been characterised and the RF beam profile has been measured at several planes to allow reconstruction of the phase and amplitude profile at the gyrotron window and to provide the necessary information permitting proper alignment of the compact RF loads prior to pulse extension. The power will be measured, according to the pulse length, using either a very-short pulse (<0.01 s) load on loan from FZK, or short-pulse (<0.2 s) or long-pulse (CW), spherical, calorimetric loads developped as part of this program by CNR. This paper presents the preliminary results of these operations.

  15. Initial Experimental Results of a Laboratory Mini-Magnetosphere for Astronaut Protection

    NASA Astrophysics Data System (ADS)

    Bamford, R. A.; Bingham, R.; Gibson, K.; Thornton, A.; Bradford, J.; Hapgood, M.; Gargate, L.; Silva, L.; Norberg, C.; Todd, T.; Wilson, H.; Stamper, R.

    2007-12-01

    Radiation is a major scientific and technological challenge for manned missions to Mars. With an interplanetary flight time of months to years there is a high probability of Solar Energetic Particle events during the flight. Radiation damage to human tissue could result in acute sickness or death of the occupants of an unprotected spacecraft. Thus there is much interest in techniques to mitigate the effects of these events and of the exposure to cosmic rays. The experimental and modelling work presented here concerns one of several innovative "Active Shield" solutions being proposed [1]. The idea of generating an artificial magnetosphere to recreate the protective shield of the Earth's magnetic field for space craft travelling to the Moon or Mars was considered seriously in the 1960's during the Apollo era. With most of the space agencies around the world setting their sights returning to the Moon and then on to Mars, the idea of some sort of active field solution is experiencing a resurgence. Results from the laboratory experiment to determine the effectiveness of a mini-magnetosphere barrier to be able to expel a flowing energetic "solar wind" plasma will be presented. This is compared to a 3D hybrid simulation code that has been successfully compared to other astrophysical situations e.g. AMPTE artificial comet releases [2]. The experiment and modelling comparisons will demonstrate the scalability between the laboratory and astrophysical scale. [1] Adams, J.H. et al., "Revolutionary Concepts of Radiation Shielding for Human Exploration of Space", NASA/TM- 2005-213688, March 2005. [2] Gargate, L.; Bingham, R.; Fonseca, R. A.; Silva, L. O., "dHybrid: A massively parallel code for hybrid simulations of space plasmas", Computer Physics Communications, Volume 176, Issue 6, Pages 419-425, 15 March 2007, doi:10.1016/j.cpc.2006.11.013

  16. Experimental investigations of the use of an erbium:YAG laser on temporomandibular joint (TMJ) structures: first experimental results

    NASA Astrophysics Data System (ADS)

    Nuebler-Moritz, Michael; Niederdellmann, Herbert; Hering, Peter; Deuerling, Christian; Dammer, Ralf; Behr, M.

    1995-04-01

    The following paper introduces the results of an interdisciplinary research project. With the aid of photomacroscopic examination, light and scanning electron microscope investigations, changes to temporomandibular joint structures were detected in vitro after irradiation with an Erbium:YAG laser system. The solid-state Erbium:YAG laser, operating at a wavelength of 2.94 micrometers was used in the normal- spiking mode. The free-running laser beam was focussed onto freshly excised porcine tissue samples using a 108-mm sapphire lens. In this study the output was generally pulsed at a repetition rate of 4 Hz, with a pulse duration varying from 120 microsecond(s) to 500 microsecond(s) . Between 50 mJ and 500 mJ per pulse were applied to create pinpoint lesions. The optimum average energy density and pulse duration of the Erbium:YAG laser radiation for the purpose of TMJ-surgery (as far as it concerns meniscus and articulating facets) - which means efficient etch rate and minimal adjacent injury - seems to be about 24-42 J/cm2 and 120 microsecond(s) -240 microsecond(s) , respectively.

  17. Data processing and display of laser Doppler experimental results, volume 1

    NASA Technical Reports Server (NTRS)

    Ashmore, B. R.; Kimura, A.; Skeith, R. W.

    1976-01-01

    Contract activities performed in developing a laser Doppler system for detecting, tracking, and measuring aircraft wake vortices are summarized. The computer program for processing and displaying the Dust Devil experimental data is presented. Program listings are included in the appendix.

  18. Prediction of sonic boom from experimental near-field overpressure data. Volume 1: Method and results

    NASA Technical Reports Server (NTRS)

    Glatt, C. R.; Hague, D. S.; Reiners, S. J.

    1975-01-01

    A computerized procedure for predicting sonic boom from experimental near-field overpressure data has been developed. The procedure extrapolates near-field pressure signatures for a specified flight condition to the ground by the Thomas method. Near-field pressure signatures are interpolated from a data base of experimental pressure signatures. The program is an independently operated ODIN (Optimal Design Integration) program which obtains flight path information from other ODIN programs or from input.

  19. Evaluating Impacts of CO2 Gas Intrusion Into a Confined Sandstone aquifer: Experimental Results

    SciTech Connect

    Qafoku, Nikolla; Lawter, Amanda R.; Shao, Hongbo; Wang, Guohui; Brown, Christopher F.

    2014-12-31

    Deep subsurface storage and sequestration of CO2 has been identified as a potential mitigation technique for rising atmospheric CO2 concentrations. Sequestered CO2 represents a potential risk to overlying aquifers if the CO2 leaks from the deep storage reservoir. Experimental and modeling work is required to evaluate potential risks to groundwater quality and develop a systematic understanding of how CO2 leakage may cause important changes in aquifer chemistry and mineralogy by promoting dissolution/precipitation, adsorption/desorption, and redox reactions. Sediments from the High Plains aquifer in Kansas, United States, were used in this investigation, which is part of the National Risk Assessment Partnership Program sponsored by the US Department of Energy. This aquifer was selected to be representative of consolidated sand and gravel/sandstone aquifers overlying potential CO2 sequestration repositories within the continental US. In this paper, we present results from batch experiments conducted at room temperature and atmospheric pressure with four High Plains aquifer sediments. Batch experiments simulate sudden, fast, and short-lived releases of the CO2 gas as would occur in the case of well failure during injection. Time-dependent release of major, minor, and trace elements were determined by analyzing the contacting solutions. Characterization studies demonstrated that the High Plains aquifer sediments were abundant in quartz and feldspars, and contained about 15 to 20 wt% montmorillonite and up to 5 wt% micas. Some of the High Plains aquifer sediments contained no calcite, while others had up to about 7 wt% calcite. The strong acid extraction tests confirmed that in addition to the usual elements present in most soils, rocks, and sediments, the High Plains aquifer sediments had appreciable amounts of As, Cd, Pb, Cu, and occasionally Zn, which potentially may be mobilized from the solid to the aqueous phase during or after exposure to CO2. However, the

  20. Effect of Hydrodynamics on Particle Transport in Saturated Fractures: Experimental and Simulation Results

    NASA Astrophysics Data System (ADS)

    Cianflone, S.; Lakhian, V.; Dickson, S. E.

    2014-12-01

    experimental results. These results suggest that local hydrodynamics are important in defining the transport of particles through a fracture. We plan to discuss further applications, general statistics, and particle retention in fractures due to hydrodynamics and ultimately the role of fracture geometry in particle transport.

  1. Evaluating Impacts of CO2 Gas Intrusion Into a Confined Sandstone aquifer: Experimental Results

    DOE PAGES

    Qafoku, Nikolla; Lawter, Amanda R.; Shao, Hongbo; Wang, Guohui; Brown, Christopher F.

    2014-12-31

    Deep subsurface storage and sequestration of CO2 has been identified as a potential mitigation technique for rising atmospheric CO2 concentrations. Sequestered CO2 represents a potential risk to overlying aquifers if the CO2 leaks from the deep storage reservoir. Experimental and modeling work is required to evaluate potential risks to groundwater quality and develop a systematic understanding of how CO2 leakage may cause important changes in aquifer chemistry and mineralogy by promoting dissolution/precipitation, adsorption/desorption, and redox reactions. Sediments from the High Plains aquifer in Kansas, United States, were used in this investigation, which is part of the National Risk Assessment Partnershipmore » Program sponsored by the US Department of Energy. This aquifer was selected to be representative of consolidated sand and gravel/sandstone aquifers overlying potential CO2 sequestration repositories within the continental US. In this paper, we present results from batch experiments conducted at room temperature and atmospheric pressure with four High Plains aquifer sediments. Batch experiments simulate sudden, fast, and short-lived releases of the CO2 gas as would occur in the case of well failure during injection. Time-dependent release of major, minor, and trace elements were determined by analyzing the contacting solutions. Characterization studies demonstrated that the High Plains aquifer sediments were abundant in quartz and feldspars, and contained about 15 to 20 wt% montmorillonite and up to 5 wt% micas. Some of the High Plains aquifer sediments contained no calcite, while others had up to about 7 wt% calcite. The strong acid extraction tests confirmed that in addition to the usual elements present in most soils, rocks, and sediments, the High Plains aquifer sediments had appreciable amounts of As, Cd, Pb, Cu, and occasionally Zn, which potentially may be mobilized from the solid to the aqueous phase during or after exposure to CO2. However

  2. Hazards by shock waves during explosive eruptions: preliminary results of experimental investigations.

    NASA Astrophysics Data System (ADS)

    Scolamacchia, Teresa; Alatorre Ibarguengoïtia, Miguel; Spieler, Oliver; Dingwell, Donald B.

    2010-05-01

    velocities (205 to 257 m/s) were obtained for smaller grain-sizes, in a range of fine lapilli-medium ash (2.8 to 177 μm). Lower velocities, 40 m/s to 85 m/s, were attained by medium (8 mm) and fine lapilli (4 mm), respectively. These values seem not directly related to the the material composition. Impacts craters on steel plates were experimentally obtained, but we did not observe a modification of the steel inner structure, as observed in the original impacted pole. These results are in agreement with impacts occurred at low particle velocities, typical for gravity driven currents, as those reached in these experiments. We observed a great reduction in grain-size of samples recovered after all experiments with respect to the original material. Such evidence coud be due not only to the disruption of grains when impacting the metal plate, but also to processes stricly related to shock wave propagation and gas expansion. These preliminary results need to be further investigated.

  3. Experimental study of the tritium distribution in the effluents resulting from the sodium hydrolysis

    SciTech Connect

    Chassery, A.; Lorcet, H.; Godlewski, J; Liger, K.; Latge, C.; Joulia, X.

    2015-03-15

    Within the framework of the dismantling of fast breeder reactors in France several processes are under investigation regarding sodium disposal. One of them, called ELA (radioactive sodium waste treatment process), is based on the implementation of the sodium-water reaction, in a controlled and progressive way, to remove residual sodium. This sodium contains impurities such as sodium hydride, sodium oxide and tritiated sodium hydride. The hydrolysis of these various chemical species leads to the production of a liquid effluent, mainly composed of an aqueous solution of sodium hydroxide, and a gaseous effluent, mainly composed of nitrogen (inert gas), hydrogen and steam. The tritium is distributed between these effluents, and, within the gaseous effluent, according to its forms HT and HTO (tritiated water). HTO being 10,000 times more radio-toxic than HT, a precise knowledge of the mechanisms governing the phase distribution of tritium is necessary. This paper presents the first experimental results from a parametric study on the tritium distribution between the various effluents generated during hydrolysis operations. A series of experiments have been performed in order to study the influence of water flow rate, argon flow rate, initial mass and specific activity of the hydrolyzed sodium sample. An important influence of the total tritium concentration in the hydrolyzed sample has been highlighted. As for the phenomena suspected to be responsible for the phase change of tritiated water, in the studied range of parameters, vaporization induced by the heat of reactions seems to be dominant over the evaporation induced by the inert gas flow rate.

  4. Effects of Added Rigid Vegetation on the Bar Formation: Results from Full-scale Experimental

    NASA Astrophysics Data System (ADS)

    Peng, K. Y.; Chen, S. C.; An, H. P.

    2015-12-01

    River corridors were characterized by island and floodplain development driven by the inter-play of flows, sediments and vegetation. This study used a natural stream as an experimental site with the site was 60m long by 30m wide, which was in downstream of Landao Creek, Huisun forest, Taiwan. The field experiment was designed to investigate the effects of river processes on bar, and the effects vegetation dynamics had on bar formation, which cause by upstream dam broke. To analysis how vegetation impact on bar-form and bar-stabilization, we used wood piles (4.4×4.4×80cm) as natural rigid vegetation, which inserted into the bar upstream. In the field site, we chose 6 site to set wood piles, each site was designed 4 row and were total 11 piles within, which set at in-row and in- line spacing of 50×20cm. According to the results, two primary phase of forming bar in the fluvial processes were discussed. First, in the flood period, presence of piles could trap large gravel in the front and turn the gravel into deposition. When the deposition gradually accreted, the front of deposition would induce flow to divide, let flow disperse into two branches around the deposition; some coarser particles rather are transported along the bar surface with momentum of flow movement and deposited at the top of bar, than are transported along the diversion channel around the bar (the median grain size of bar top were coarser 50% than before). Second, in the flood recession period, bar quickly accreted portions of passing bed load sheets and grew laterally and in the headward direction. Phenomenon showed that the composition of grain size were decreasing in the headward direction, which flow entrained were getting smaller with flood recession (the median grain size between top and the front of bar differed 30%).

  5. Linking experimental results, biological networks and sequence analysis methods using Ontologies and Generalised Data Structures.

    PubMed

    Koehler, Jacob; Rawlings, Chris; Verrier, Paul; Mitchell, Rowan; Skusa, Andre; Ruegg, Alexander; Philippi, Stephan

    2005-01-01

    The structure of a closely integrated data warehouse is described that is designed to link different types and varying numbers of biological networks, sequence analysis methods and experimental results such as those coming from microarrays. The data schema is inspired by a combination of graph based methods and generalised data structures and makes use of ontologies and meta-data. The core idea is to consider and store biological networks as graphs, and to use generalised data structures (GDS) for the storage of further relevant information. This is possible because many biological networks can be stored as graphs: protein interactions, signal transduction networks, metabolic pathways, gene regulatory networks etc. Nodes in biological graphs represent entities such as promoters, proteins, genes and transcripts whereas the edges of such graphs specify how the nodes are related. The semantics of the nodes and edges are defined using ontologies of node and relation types. Besides generic attributes that most biological entities possess (name, attribute description), further information is stored using generalised data structures. By directly linking to underlying sequences (exons, introns, promoters, amino acid sequences) in a systematic way, close interoperability to sequence analysis methods can be achieved. This approach allows us to store, query and update a wide variety of biological information in a way that is semantically compact without requiring changes at the database schema level when new kinds of biological information is added. We describe how this datawarehouse is being implemented by extending the text-mining framework ONDEX to link, support and complement different bioinformatics applications and research activities such as microarray analysis, sequence analysis and modelling/simulation of biological systems. The system is developed under the GPL license and can be downloaded from http://sourceforge.net/projects/ondex/

  6. Bispecific-antibody-mediated targeting of radiolabeled bivalent haptens: theoretical, experimental and clinical results.

    PubMed

    Le Doussal, J M; Barbet, J; Delaage, M

    1992-01-01

    Chemically conjugated bispecific (anti-cell surface antigen, anti-hapten) Fab'-Fab antibodies (Bs-MAbs) have been used to target 125I-, 111In- and 99mTc-labeled haptens to cell sub-sets. In vitro, bivalent haptens were found to bind more strongly than their monovalent analogs to the Bs-MAbs bound to ("ordered" on) the cell surface, or than to free ("disordered") Bs-MAbs: they are selective for cell-bound Bs-MAbs. In tumor-grafted nude mice models, the sequential injections of microgram amounts of Bs-MAb, and 1 day later, of microC amounts of bivalent haptens permits to sharply delineate small tumors (using a gamma camera), hours after injection. Further, the isotope biodistribution was found to be at least 3 times more selective for the tumor than that obtained with directly labeled anti-CEA F(ab)'2 or with monovalent haptens. This better in vivo selectivity of the 2-step targeting of bivalent haptens was also demonstrated in a pharmacokinetic study using therapeutic amounts of reagents. In primary-colon-carcinoma patients, a similar comparative immunoscintigraphy study confirmed the better selectivity of bivalent hapten targeting over direct targeting, on the basis of image quality and ex vivo tissue counting. In patients with medullary carcinoma of the thyroid, bivalent hapten targeting allowed us to confirm tumor extension and to find occult lesions. Interestingly, radio-immunoguided surgery was necessary to resect these small lesions. These experimental results, together with technological and theoretical considerations, suggest that Bs-MAb-mediated targeting of isotopes (or other agents) is one of the major ways to increase the clinical performance of MAb-based targeting diagnostic and therapeutic tools.

  7. Chaotic scattering in an open vase-shaped cavity: Topological, numerical, and experimental results

    NASA Astrophysics Data System (ADS)

    Novick, Jaison Allen

    point to each "detector point". We then construct the wave function directly from these classical trajectories using the two-dimensional WKB approximation. The wave function is Fourier Transformed using a Fast Fourier Transform algorithm resulting in a spectrum in which each peak corresponds to an interpolated trajectory. Our predictions are based on an imagined experiment that uses microwave propagation within an electromagnetic waveguide. Such an experiment exploits the fact that under suitable conditions both Maxwell's Equations and the Schrodinger Equation can be reduced to the Helmholtz Equation. Therefore, our predictions, while compared to the electromagnetic experiment, contain information about the quantum system. Identifying peaks in the transmission spectrum with chaotic trajectories will allow for an additional experimental verification of the intermediate recursive structure. Finally, we summarize our results and discuss possible extensions of this project.

  8. Modeling the Fracturing of Rock by Fluid Injection - Comparison of Numerical and Experimental Results

    NASA Astrophysics Data System (ADS)

    Heinze, Thomas; Galvan, Boris; Miller, Stephen

    2013-04-01

    Fluid-rock interactions are mechanically fundamental to many earth processes, including fault zones and hydrothermal/volcanic systems, and to future green energy solutions such as enhanced geothermal systems and carbon capture and storage (CCS). Modeling these processes is challenging because of the strong coupling between rock fracture evolution and the consequent large changes in the hydraulic properties of the system. In this talk, we present results of a numerical model that includes poro-elastic plastic rheology (with hardening, softening, and damage), and coupled to a non-linear diffusion model for fluid pressure propagation and two-phase fluid flow. Our plane strain model is based on the poro- elastic plastic behavior of porous rock and is advanced with hardening, softening and damage using the Mohr- Coulomb failure criteria. The effective stress model of Biot (1944) is used for coupling the pore pressure and the rock behavior. Frictional hardening and cohesion softening are introduced following Vermeer and de Borst (1984) with the angle of internal friction and the cohesion as functions of the principal strain rates. The scalar damage coefficient is assumed to be a linear function of the hardening parameter. Fluid injection is modeled as a two phase mixture of water and air using the Richards equation. The theoretical model is solved using finite differences on a staggered grid. The model is benchmarked with experiments on the laboratory scale in which fluid is injected from below in a critically-stressed, dry sandstone (Stanchits et al. 2011). We simulate three experiments, a) the failure a dry specimen due to biaxial compressive loading, b) the propagation a of low pressure fluid front induced from the bottom in a critically stressed specimen, and c) the failure of a critically stressed specimen due to a high pressure fluid intrusion. Comparison of model results with the fluid injection experiments shows that the model captures most of the experimental

  9. Sodium laser guide star system at Lawrence Livermore National Laboratory: System description and experimental results

    SciTech Connect

    Avicola, K.; Brase, J.; Morris, J.

    1994-03-02

    The architecture and major system components of the sodium-layer kw guide star system at LLNL will be described, and experimental results reported. The subsystems include the laser system, the beam delivery system including a pulse stretcher and beam pointing control, the beam director, and the telescope with its adaptive-optics package. The laser system is one developed for the Atomic Vapor Laser Isotope Separation (AVLIS) Program. This laser system can be configured in various ways in support of the AVLIS program objectives, and was made available to the guide star program at intermittent times on a non-interference basis. The first light transmitted into the sky was in July of 1992, at a power level of 1. 1 kW. The laser pulse width is about 32 ns, and the pulse repetition rate was 26 kHz for the 1. 1 kW configuration and 13 kHz for a 400 W configuration. The laser linewidth is tailored to match the sodium D{sub 2} absorption line, and the laser system has active control of beam pointing and wavefront quality. Because of the short pulse length the sodium transition is saturated and the laser power is not efficiently utilized. For this reason a pulse stretcher was developed, and the results of this effort will be reported. The beam is delivered via an evacuated pipe from the laser building to the guide star site, a distance of about 100 meters, and then launched vertically. A beam director provides the means to track the sky in the full AO system, but was not used in the experiments reported here. The return signal is collected by a 1/2 meter telescope with the AO package. This telescope is located 5 meters from the km launch tube. Smaller packages for photometry, wavefront measurement, and spot image and motion analysis have been used. Although the unavailability of the AVLIS laser precluded a full AO system demonstration, data supporting feasibility and providing input to the system design for a Lick Observatory AO system was obtained.

  10. Chlorine Stable Isotope Composition of Altered Oceanic Crust: Empirical and Experimental Results

    NASA Astrophysics Data System (ADS)

    Barnes, J.; Gardner, J. E.

    2010-12-01

    be ~ +2-3‰ heavier than those in which Cl bonds with 1+ cations (Schauble et al., 2003). These calculations have led to the hypothesis that silicates should have higher 37Cl/35Cl ratios than co-existing brines at room temperature (Schauble et al., 2003). Preliminary Cl isotope fractionation experiments between pargasitic amphibole and either seawater or brine (25 wt% NaCl solution) were run in cold-seal pressure vessels at 600°C and 500 bars. Preliminary results suggest that Δ37Clpargasite-Cl(aq) is within analytical error of the theoretically predicted fractionation factor, as well as measured δ37Cl values of AOC samples. Further work is planned to investigate the role of fluid-rock ratio and amphibole composition. Additional experimental data may allow us to infer the fluid-rock ratio and temperature during hydration of natural samples and to unravel the fluid histories recorded in the alteration minerals.

  11. Experimental determination of the solubility of iridium in silicate melts: Preliminary results

    NASA Technical Reports Server (NTRS)

    Borisov, Alexander; Dingwell, Donald B.; Oneill, Hugh ST.C.; Palme, Herbert

    1992-01-01

    Little is known of the geochemical behavior of iridium. Normally this element is taken to be chalcophile and/or siderophile so that during planetary differentiation processes, e.g., core formation, iridium is extracted from silicate phases into metallic phases. Experimental determination of the metal/silicate partition coefficient of iridium is difficult simply because it is so large. Also there are no data on the solubility behavior of iridium in silicate melts. With information on the solubility of iridium in silicate melts it is possible, in combination with experimental data for Fe-Ir alloys, to calculate the partition coefficient between a metallic phase and a silicate melt.

  12. Understanding how hydrodynamics affects particle transport in saturated fractures using modelling and experimental results

    NASA Astrophysics Data System (ADS)

    Cianflone, S.; Lakhian, V.; Dickson, S. E.

    2013-12-01

    poly(methyl methacrylate), thus creating a pseudo-2D fracture. Namely, the 2D fracture (x-y coordinates) is cut into the plastic using a laser printer, thus the z-coordinate is constant to a depth of 2.3 mm. Experiments using Acid Yellow 17, as a tracer, as well as fluorescent microspheres (42.5 nm and 525 nm, non-carboxylated to minimize attachment/detachment) will be performed in order to compare simulations and experimental results. Concentrations of the microspheres and tracer were measured at the effluent end of the fracture where the end cap housed an LED (400-470 nm) and an optical fibre attached to a spectrophotometer. Simulations suggest that in fractures where eddies occur, there is retention of smaller particles only when there is sufficient diffusion and a slow enough fluid velocity to allow them to enter the eddy. Otherwise, the particles exit the fracture earlier than typically expected when considering particle size exclusion and average fluid velocity. Further modelling results suggest that using bulk measurements (eg. mean aperture, mean fluid velocity, and measures of fracture roughness) to predict the resultant particulate outflow in a saturated fracture is difficult. We plan to include visualization experiments in order to draw further comparisons to the modelling results.

  13. The actual goals of geoethics

    NASA Astrophysics Data System (ADS)

    Nemec, Vaclav

    2014-05-01

    The most actual goals of geoethics have been formulated as results of the International Conference on Geoethics (October 2013) held at the geoethics birth-place Pribram (Czech Republic): In the sphere of education and public enlightenment an appropriate needed minimum know how of Earth sciences should be intensively promoted together with cultivating ethical way of thinking and acting for the sustainable well-being of the society. The actual activities of the Intergovernmental Panel of Climate Changes are not sustainable with the existing knowledge of the Earth sciences (as presented in the results of the 33rd and 34th International Geological Congresses). This knowledge should be incorporated into any further work of the IPCC. In the sphere of legislation in a large international co-operation following steps are needed: - to re-formulate the term of a "false alarm" and its legal consequences, - to demand very consequently the needed evaluation of existing risks, - to solve problems of rights of individuals and minorities in cases of the optimum use of mineral resources and of the optimum protection of the local population against emergency dangers and disasters; common good (well-being) must be considered as the priority when solving ethical dilemmas. The precaution principle should be applied in any decision making process. Earth scientists presenting their expert opinions are not exempted from civil, administrative or even criminal liabilities. Details must be established by national law and jurisprudence. The well known case of the L'Aquila earthquake (2009) should serve as a serious warning because of the proven misuse of geoethics for protecting top Italian seismologists responsible and sentenced for their inadequate superficial behaviour causing lot of human victims. Another recent scandal with the Himalayan fossil fraud will be also documented. A support is needed for any effort to analyze and to disclose the problems of the deformation of the contemporary

  14. A Two-Year Report on the Experimental Freshman Year Program. Chapter IV, Results.

    ERIC Educational Resources Information Center

    Kibler, Robert J., Ed.

    Chapter IV describes the interim findings of an experimental program for underachieving high school graduates during their freshman year at Southern Illinois University. The statistically analyzed data are presented and discussed under four headings--(1) Subjects' occupation or whereabouts in the year following their participation in the program,…

  15. Multiple Measures of Juvenile Drug Court Effectiveness: Results of a Quasi-Experimental Design

    ERIC Educational Resources Information Center

    Rodriguez, Nancy; Webb, Vincent J.

    2004-01-01

    Prior studies of juvenile drug courts have been constrained by small samples, inadequate comparison groups, or limited outcome measures. The authors report on a 3-year evaluation that examines the impact of juvenile drug court participation on recidivism and drug use. A quasi-experimental design is used to compare juveniles assigned to drug court…

  16. Comparison of Breast Health Teaching Methods for Adolescent Females: Results of a Quasi-Experimental Study

    ERIC Educational Resources Information Center

    Evans, Retta R.; Horton, Jacqueline A.; Ahmad, Wajih A.; Davies, Susan L.; Snyder, Scott W.; Macrina, David M.

    2013-01-01

    Purpose: A breast health educational program was administered in two public high school settings in north Alabama to subjects enrolled in health related courses. The purpose of this quasi-experimental study was to determine if teaching breast health with or without interactive learning would affect the breast health knowledge and beliefs of…

  17. OVERVIEW OF RECENT EXPERIMENTAL RESULTS FROM THE DIII-D ADVANCED TOKAMAK PROGRAM

    SciTech Connect

    BURRELL,KH

    2002-11-01

    OAK A271 OVERVIEW OF RECENT EXPERIMENTAL RESULTS FROM THE DIII-D ADVANCED TOKAMAK PROGRAM. The DIII-D research program is developing the scientific basis for advanced tokamak (AT) modes of operation in order to enhance the attractiveness of the tokamak as an energy producing system. Since the last International Atomic Energy Agency (IAEA) meeting, the authors have made significant progress in developing the building blocks needed for AT operation: (1) the authors have doubled the magnetohydrodynamic (MHD) stable tokamak operating space through rotational stabilization of the resistive wall mode; (2) using this rotational stabilization, they have achieved {beta}{sub N}H{sub 89} {le} 10 for 4 {tau}{sub E} limited by the neoclassical tearing mode; (3) using real-time feedback of the electron cyclotron current drive (ECCD) location, they have stabilized the (m,n) = (3,2) neoclassical tearing mode and then increased {beta}{sub T} by 60%; (4) they have produced ECCD stabilization of the (2,1) neoclassical tearing mode in initial experiments; (5) they have made the first integrated AT demonstration discharges with current profile control using ECCD; (6) ECCD and electron cyclotron heating (ECH) have been used to control the pressure profile in high performance plasmas; and (7) they have demonstrated stationary tokamak operation for 6.5 s (36 {tau}{sub E}) at the same fusion gain parameter of {beta}{sub N}H{sub 89}/q{sub 95}{sup 2} {approx} 0.4 as ITER but at much higher q{sub 95} = 4.2. They have developed general improvements applicable to conventional and advanced tokamak operating modes: (1) they have an existence proof of a mode of tokamak operation, quiescent H-mode, which has no pulsed, ELM heat load to the divertor and which can run for long periods of time (3.8 s or 25 {tau}{sub E}) with constant density and constant radiation power; (2) they have demonstrated real-time disruption detection and mitigation for vertical disruption events using high pressure gas jet

  18. Robotic Exploration and Science in Pits and Caves: Results from Three Years and Counting of Analog Field Experimentation

    NASA Astrophysics Data System (ADS)

    Wong, U. Y.; Whittaker, W. L.

    2015-10-01

    Robots are poised to access, investigate, and model planetary caves. We present the results of a multi-year campaign to develop robotic technologies for this domain, anchored by the most comprehensive analog field experimentation to date.

  19. Experimental warming delays autumn senescence in a boreal spruce bog: Initial results from the SPRUCE experiment

    NASA Astrophysics Data System (ADS)

    Richardson, Andrew; Furze, Morgan; Aubrecht, Donald; Milliman, Thomas; Nettles, Robert; Krassovski, Misha; Hanson, Paul

    2016-04-01

    Phenology is considered one of the most robust indicators of the biological impacts of global change. In temperate and boreal regions, long-term data show that rising temperatures are advancing spring onset (e.g. budburst and flowering) and delaying autumn senescence (e.g. leaf coloration and leaf fall) in a wide range of ecosystems. While warm and cold temperatures, day length and insolation, precipitation and water availability, and other factors, have all been shown to influence plant phenology, the future response of phenology to rising temperatures and elevated CO2 still remains highly uncertain because of the challenges associated with conducting realistic manipulative experiments to simulate future environmental conditions. At the SPRUCE (Spruce and Peatland Responses Under Climatic and Environmental Change) experiment in the north-central United States, experimental temperature (0 to +9° C above ambient) and CO2 (ambient and elevated) treatments are being applied to mature, and intact, Picea mariana-Sphagnum spp. bog communities in their native habitat through the use of ten large (approximately 12 m wide, 10 m high) open-topped enclosures. We are tracking vegetation green-up and senescence in these chambers, at both the individual and whole-community level, using repeat digital photography. Within each chamber, digital camera images are recorded every 30 minutes and uploaded to the PhenoCam (http://phenocam.sr.unh.edu) project web page, where they are displayed in near-real-time. Image processing is conducted nightly to extract quantitative measures of canopy color, which we characterize using Gcc, the green chromatic coordinate. Data from a camera mounted outside the chambers (since November 2014) indicate strong seasonal variation in Gcc for both evergreen shrubs and trees. Shrub Gcc rises steeply in May and June, and declines steeply in September and October. By comparison, tree Gcc rises gradually from March through June, and declines gradually from

  20. Realizing actual feedback control of complex network

    NASA Astrophysics Data System (ADS)

    Tu, Chengyi; Cheng, Yuhua

    2014-06-01

    In this paper, we present the concept of feedbackability and how to identify the Minimum Feedbackability Set of an arbitrary complex directed network. Furthermore, we design an estimator and a feedback controller accessing one MFS to realize actual feedback control, i.e. control the system to our desired state according to the estimated system internal state from the output of estimator. Last but not least, we perform numerical simulations of a small linear time-invariant dynamics network and a real simple food network to verify the theoretical results. The framework presented here could make an arbitrary complex directed network realize actual feedback control and deepen our understanding of complex systems.

  1. El Observatorio Gemini - Status actual

    NASA Astrophysics Data System (ADS)

    Levato, H.

    Se hace una breve descripción de la situación actual del Observatorio Gemini y de las últimas decisiones del Board para incrementar la eficiencia operativa. Se hace también una breve referencia al uso argentino del observatorio.

  2. Rb-Sr, K-Ar and fission track ages for granites from Penang Island, West Malaysia: an interpretation model for Rb-Sr whole-rock and for actual and experimental mica data

    NASA Astrophysics Data System (ADS)

    Kwan, T. S.; Krähenbühl, R.; Jager, E.

    1992-09-01

    Penang Island represents the northwestern extension of the western magmatic belt of Peninsular Malaysia. Thirty-one samples of highly evolved biotite-and biotite-muscovite granites were used in an integrated study to unravel the complex magmatic, tectonic and cooling histories of these rocks. Highly distorted Rb-Sr whole-rock age patterns are evident. These are attributed to the partial post-magmatic Sr homogenization within the granite batholith which led to the rotation of isochrons towards younger ages and higher (87/86)Sr intercepts. The recognition of this mechanism allowed the establishment of a new Rb-Sr interpretation model. The intrusion ages of the granites can be extrapolated based on the evolutionary trend of the initial (87/86)Sr. Including the data of Bignell and Snelling, three episodes of granite emplacement at 307±8 Ma, 251±7 Ma and 211±2 Ma are suggested for Penang and the NW Main Range. The late-Triassic intrusive induced a hydrothermal conductive convection system which affected all the granites. It is considered to be responsible for the Rb-Sr whole-rock age distortion, the Rb-Sr and K-Ar biotite age resetting and the textural and mineralogical changes in the granites. The duration of the hydrothermal convections, deduced from the Rb-Sr whole rock ages, is about 6 Ma and 20 Ma in the northern and southern parts of Penang respectively. Fast regional cooling to 350±50°C within a time span of 1 3 Ma is recognized for the late-Triassic Feringgi intrusive from the mica ages, followed by a generally slow cooling rate of about 1°C/Ma. Fission track ages, in addition, indicate blockwise uplift along the N-S and NW-SE tending faults, thus resulting in the exposure of deeper crustal levels in southern and eastern Penang. A change in the tensional regime since Oligocene/Miocene, accompanied by a southwest tilting of the island, is indicated by the fission track apatite ages. Variable sometimes younger K-Ar, respectively Rb-Sr biotite ages mainly

  3. Cold Climate Foundation Retrofit Experimental Hygrothermal Performance. Cloquet Residential Research Facility Laboratory Results

    SciTech Connect

    Goldberg, Louise F.; Harmon, Anna C.

    2015-04-09

    This project was funded jointly by the National Renewable Energy Laboratory (NREL) and Oak Ridge National Laboratory (ORNL). ORNL focused on developing a full basement wall system experimental database to enable others to validate hygrothermal simulation codes. NREL focused on testing the moisture durability of practical basement wall interior insulation retrofit solutions for cold climates. The project has produced a physically credible and reliable long-term hygrothermal performance database for retrofit foundation wall insulation systems in zone 6 and 7 climates that are fully compliant with the performance criteria in the 2009 Minnesota Energy Code. These data currently span the period from November 10, 2012 through May 31, 2014 and are anticipated to be extended through November 2014. The experimental data were configured into a standard format that can be published online and that is compatible with standard commercially available spreadsheet and database software.

  4. Experimental and computational results for 5 degree blunt cones with shock generators at high velocity

    NASA Technical Reports Server (NTRS)

    Strawa, A. W.; Molvik, G. A.; Yates, L. A.; Cornelison, C.

    1989-01-01

    Experiments and computations have been performed under laminar conditions in air on 5-deg blunt cones at velocities of 5 km/s and 6 km/s and at Reynolds numbers of 100,000 and 1 million. The computations were performed using ideal-, equilibrium- and nonequilibrium-chemistry models for air. At the conditions of the tests, the aerodynamic coefficients are sensitive to the real-gas effects present, and both experimental and computational aerodynamic coefficients show real-gas and nonlinear effects. The nonequilibrium computations show that a large amount of oxygen is dissociated in the blunt nose region of the flow and much of the oxygen remains dissociated over the entire length of the body, providing an insight into the source of the observed effects in the aerodynamic coefficients. The experimental and computational shock-shapes are in good agreement.

  5. Experimental results of water film formation on various fuel forms from a fire suppression system

    SciTech Connect

    Ross, R.H.; Davis, J.R.

    1993-12-31

    The purpose of the study was to determine the thickness and coverage of water film formations on various materials during fire sprinkler deluge. An exhaustive literature search revealed that no applicable research data exists that governs water film formations from fire protection systems. Therefore, a controlled, infield, mockup was created to predict the thickness and coverage of water film on fissile material forms. This paper discusses the background, experimental procedure and the characterization of these water films.

  6. Preliminary experimental results of gas recycling subsystems except carbon dioxide concentration

    NASA Astrophysics Data System (ADS)

    Otsuji, K.; Sawada, T.; Satoh, S.; Kanda, S.; Matsumura, H.; Kondo, S.; Otsubo, K.

    Oxygen concentration and separation is an essential factor for air recycling in a CELSS. Furthermore, if the value of the plant assimilatory quotient is not coincident with that of the animal respiratory quotient, the recovery of O2 from the concentrated CO2 through chemical methods will become necessary to balance the gas contents in a CELSS. Therefore, oxygen concentration and separation equipment using Salcomine and O2 recovery equipment, such as Sabatier and Bosch reactors, were experimentally developed and tested.

  7. Experimental results from RO-PRO: a next generation system for low-energy desalination.

    PubMed

    Achilli, Andrea; Prante, Jeri L; Hancock, Nathan T; Maxwell, Eric B; Childress, Amy E

    2014-06-01

    A pilot system was designed and constructed to evaluate reverse osmosis (RO) energy reduction that can be achieved using pressure-retarded osmosis (PRO). The RO-PRO experimental system is the first known system to utilize energy from a volume of water transferred from atmospheric pressure to elevated pressure across a semipermeable membrane to prepressurize RO feedwater. In other words, the system demonstrated that pressure could be exchanged between PRO and RO subsystems. Additionally, the first experimental power density data for a RO-PRO system is now available. Average experimental power densities for the RO-PRO system ranged from 1.1 to 2.3 W/m2. This is higher than previous river-to-sea PRO pilot systems (1.5 W/m2) and closer to the goal of 5 W/m2 that would make PRO an economically feasible technology. Furthermore, isolated PRO system testing was performed to evaluate PRO element performance with higher cross-flow velocities and power densities exceeding 8 W/m2 were achieved with a 28 g/L NaCl draw solution. From this empirical data, inferences for future system performance can be drawn that indicate future RO-PRO systems may reduce the specific energy requirements for desalination by ∼1 kWh/m3.

  8. Boundary conditions for creeping flow along periodic or random rough surfaces : experimental and theoretical results

    NASA Astrophysics Data System (ADS)

    Lecoq, Nicolas

    2012-12-01

    Hydrodynamic interactions between particles and walls are relevant for the open problem of specifying boundary conditions for suspension flows. The Reynolds number around a small particle close to a wall is usually low and creeping flow equations apply. From the solution of these equations, the drag coefficient on a sphere becomes infinite when the gap between the sphere and a smooth wall vanishes, so that contact may not occur. Physically, the drag is finite because of various reasons, one of them being the particle and wall roughness. Then, for vanishing gap, even though some layers of fluid molecules may be left between the particle and wall roughness peaks, it may conventionally be said that contact occurs. In this paper, we are considering the example of a smooth sphere moving towards a rough wall. The roughness considered here consist of random rough planes or parallel periodic wedges, the characteristic length of which is small compared with the sphere radius. This problem is considered both experimentally and theoretically. The motion of a millimetre size bead settling towards a corrugated horizontal wall in a viscous oil is measured with laser interferometry giving an accuracy on the displacement of 0.2μm. Several random rough planes and wedge shaped walls were used, with various wavelengths and wedge angles. From the results, it is observed that the velocity of the sphere is, except for small gaps, similar to that towards a smooth plane that is shifted down from the top of corrugations. For the periodic wedges, the creeping flow is calculated as a series in the slope of the roughness grooves. The convergence of the series for the shift distance in term of the slope is accelerated by use of Euler transformation and of the existence of a limit for large slope. The cases of a flow along and across the grooves are considered separately. The shift is larger in the former case. Slightly flattened tops of the wedges used in experiments are also considered in

  9. OVERVIEW OF RECENT EXPERIMENTAL RESULTS FROM THE DIII-D ADVANCED TOKAMAK PROGRAM

    SciTech Connect

    BURRELL,HK

    2002-11-01

    OAK A271 OVERVIEW OF RECENT EXPERIMENTAL RESULTS FROM THE DIII-D ADVANCED TOKAMAK PROGRAM. The DIII-D research program is developing the scientific basis for advanced tokamak (AT) modes of operation in order to enhance the attractiveness of the tokamak as an energy producing system. Since the last International Atomic Energy Agency (IAEA) meeting, they have made significant progress in developing the building blocks needed for AT operation: (1) they have doubled the magnetohydrodynamic (MHD) stable tokamak operating space through rotational stabilization of the resistive wall mode; (2) using this rotational stabilization, they have achieved {beta}{sub N}H{sub 89} {ge} 10 for 4 {tau}{sub E} limited by the neoclassical tearing mode; (3) using real-time feedback of the electron cyclotron current drive (ECCD) location, they have stabilized the (m,n) = (3,2) neoclassical tearing mode and then increased {beta}{sub T} by 60%; (4) they have produced ECCD stabilization of the (2,1) neoclassical tearing mode in initial experiments; (5) they have made the first integrated AT demonstration discharges with current profile control using ECCD; (6) ECCD and electron cyclotron heating (ECH) have been used to control the pressure profile in high performance plasmas; and (7) they have demonstrated stationary tokamak operation for 6.5 s (36 {tau}{sub E}) at the same fusion gain parameter of {beta}{sub N}H{sub 89}/q{sub 95}{sup 2} {approx} 0.4 as ITER but at much higher q{sub 95} = 4.2. The authors have developed general improvements applicable to conventional and advanced tokamak operating modes: (1) they have an existence proof of a mode of tokamak operation, quiescent H-mode, which has no pulsed, ELM heat load to the divertor and which can run for long periods of time (3.8 s or 25 {tau}{sub E}) with constant density and constant radiated power; (2) they have demonstrated real-time disruption detection and mitigation for vertical disruption events using high pressure gas jet

  10. Experimental segregation of iron-nickel metal, iron-sulfide, and olivine in a thermal gradient: Preliminary results

    NASA Technical Reports Server (NTRS)

    Jurewicz, Stephen R.; Jones, J. H.

    1993-01-01

    Speculation about the possible mechanisms for core formation in small asteroids raises more questions than answers. Petrologic evidence from iron meteorites, pallasites, and astronomical observations of M asteroids suggests that many small bodies were capable of core formation. Recent work by Taylor reviews the geochemical evidence and examines the possible physical/mechanical constraints on segregation processes. Taylor's evaluation suggests that extensive silicate partial melting (preferably 50 vol. percent or greater) is required before metal can segregate from the surrounding silicate and form a metal core. The arguments for large degrees of silicate partial melting are two-fold: (1) elemental trends in iron meteorites require that the metal was at is liquidus; and (2) experimental observations of metal/sulfide inclusions in partially molten silicate meteorites show that the metal/sulfide tends to form spherules in the liquid silicate due to surface tension effects. Taylor points out that for these metal spherules to sink through a silicate mush, high degrees of silicate partial melting are required to lower the silicate yield strength. Although some qualitative experimental data exists, little is actually known about the behavior of metals and liquid sulfides dispersed in silicate systems. In addition, we have been impressed with the ability of cumulative olivine to expel trapped liquid when placed in a thermal gradient. Consequently, we undertook to accomplish the following: (1) experimentally evaluate the potential for metal/sulfide/silicate segregation in a thermal gradient; and (2) obtain quantitative data of the wetting parameters of metal-sulfide melts among silicate grains.

  11. Charging characteristics of materials: Comparison of experimental results with simple analytical models

    NASA Technical Reports Server (NTRS)

    Purvis, C. K.; Stevens, N. J.; Oglebay, J. C.

    1977-01-01

    An understanding of the behavior of materials, of dielectrics in particular, under charged particle bombardment is essential to the prediction and prevention of the adverse effects of spacecraft charging. A one-dimensional model for charging of samples in a test facility was used in conjunction with experimental data taken to develop "material charging characteristics" for silvered Teflon. These characteristics were then used in a one-dimensional model for charging in space to examine expected response. Relative charging rates as well as relative charging levels for silvered Teflon and metal are discussed.

  12. Homogenizing a Nickel-Based Superalloy: Thermodynamic and Kinetic Simulation and Experimental Results

    SciTech Connect

    Paul D. Jablonski; Christopher J. Cowen

    2009-03-01

    If the chemical inhomogeneity profile is known a priori, kinetic modeling software such as diffusion-controlled transformations (DICTRA) can be used to model the homogenization kinetics of an alloy. In this study, the Scheil module within the Thermo-Calc software was used to predict the as-cast segregation present within the Ni-based superalloy Nimonic 105. The segregation profiles were read into DICTRA to refine the homogenization heat treatment of this alloy. The thermodynamic and kinetic modeling of the computationally predicted heat treatment and microstructure, and subsequent experimental verification on a real casting of Nimonic 105, are presented.

  13. Literature review and experimental results for a cylinder with perforations and protrusions at high Reynolds numbers

    NASA Technical Reports Server (NTRS)

    Jones, G. S.; Horvath, T. J.; Stainback, P. C.; Beasley, W. D.; Mcghee, R. J.

    1987-01-01

    The NASA Langley Low Turbulence Pressure Tunnel has been used to conduct an experimental study of the flow around a series of circular cylinders; the models used consisted of a baseline, smooth cylinder together with a cylinder that could be reconfigured with six different arrangements of two types of surface irregularity. Mean lift and drag forces were measured on all seven model configurations, and correlations were made between unsteady pressure in the wake region and fluctuating lift forces, in order to identify coherent structures.

  14. Nanoparticle detection limits of TNO's Rapid Nano: modeling and experimental results

    NASA Astrophysics Data System (ADS)

    van der Walle, Peter; Kumar, Pragati; Ityaksov, Dmitry; Versulis, Richard; Maas, Diederik J.; Kievit, Olaf; Janssen, Jochem; van der Donck, Jacques C. J.

    2012-11-01

    TNO has developed the Rapid Nano scanner to detect nanoparticles on EUVL mask blanks. This scanner was designed to be used in particle qualifications of EUV reticle handling equipment. In this paper we present an end-to-end model of the Rapid Nano detection process. All important design parameters concerning illumination, detection and noise are included in the model. The prediction from the model matches the performance that was experimentally determined (59 nm LSE). The model will be used to design and predict the performance of future generations of particle scanners.

  15. Preliminary experimental results of gas recycling subsystems except carbon dioxide concentration

    NASA Technical Reports Server (NTRS)

    Otsuji, K.; Sawada, T.; Satoh, S.; Kanda, S.; Matsumura, H.; Kondo, S.; Otsubo, K.

    1987-01-01

    Oxygen concentration and separation is an essential factor for air recycling in a controlled ecological life support system (CELSS). Furthermore, if the value of the plant assimilatory quotient is not coincident with that of the animal respiratory quotient, the recovery of oxygen from the concentrated CO2 through chemical methods will become necessary to balance the gas contents in a CELSS. Therefore, oxygen concentration and separation equipment using Salcomine and O2 recovery equipment, such as Sabatier and Bosch reactors, were experimentally developed and tested.

  16. Results of experimental tests and calibrations of the surface neutron moisture measurement probe

    SciTech Connect

    Watson, W.T.; Bussell, J.H., Westinghouse Hanford

    1996-08-13

    The surface neutron moisture probe has been tested both to demonstrate that is is able to operate in the expected in-tank temperature and gamma-ray fields and to provide detector responses to known moisture concentration materials. The probe will properly function in a simultaneous high temperature (80 degrees C) and high gamma radiation field (210 rad/hr)environment. Comparisons between computer model predicted and experimentally measured detector responses to changes in moisture provide a basis for the probe calibration to in-tank moisture concentrations.

  17. Experimental and computational surface and flow-field results for an all-body hypersonic aircraft

    NASA Technical Reports Server (NTRS)

    Lockman, William K.; Lawrence, Scott L.; Cleary, Joseph W.

    1990-01-01

    Personnel from NASA Ames Research Center presented a paper on establishing a benchmark experimental data base for generic hypersonic vehicle shape for validation and/or calibration of advanced computational fluid dynamics computer codes. The need for this capability is based on a requirement for extensive hypersonic data to fully validate CFD codes to be used for NASP and other hypersonic vehicles. The use of wind tunnel models in the Ames 3.5-ft Hypersonic Wind Tunnel to obtain pertinent surface and flow-field data over a broad range of test conditions is described.

  18. Experimental studies on benzene carcinogenicity at the Bologna Institute of Oncology: current results and ongoing research.

    PubMed

    Maltoni, C; Conti, B; Cotti, G; Belpoggi, F

    1985-01-01

    In 1977 Maltoni and Scarnato were the first to demonstrate that benzene is an experimental carcinogen in rats. With that and other experiments, Maltoni et al have shown that benzene administered by ingestion (stomach tube) or inhalation is a multipotential carcinogen in rats (of two different strains) and mice and produces a variety of tumors, namely: Zymbal gland carcinomas, oral and nasal cavity carcinomas, skin carcinomas, acanthomas, dysplasias and carcinomas of forestomach, mammary malignant tumors, hepatomas, liver angiosarcomas, hemolymphoreticular neoplasias, and pulmonary tumors. The incidence of Zymbal gland carcinomas and carcinomas of the oral and nasal cavities is affected by the length of treatment by inhalation and by the age of animals. However, the available epidemiological and experimental data at present do not provide precise information on the risk of doses around or below 10 ppm. Long-term carcinogenicity bioassays at 50, 25, 10, 5 and 1 ppm may be helpful for scientific risk assessment. In addition, these experiments have shown that toluene, xylene, and ethylbenzene, at high concentrations, cause an increase in the number of total malignant tumors.

  19. Transmission and phase balancing of alternating phase-shifting masks (5x): theoretical and experimental results

    NASA Astrophysics Data System (ADS)

    Griesinger, Uwe A.; Pforr, Rainer; Knobloch, Juergen; Friedrich, Christoph M.

    1999-12-01

    Dual trench alternating phase shifting masks with an optimized value of the so-called shallow trench depth represents an interesting approach to overcome aerial image imbalances. In order to get a better understanding of the possibilities and limits of this approach, especially for 5X reduction, theoretical and experimental investigations were accomplished. In this paper experimental data obtained from 5X dual trench type alternating PSMs, using DUV-lithography are introduced and compared with 3D-mask simulations. The masks were fabricated with different etch depths and contain parts of typical DRAM patterns. Besides the transmission balancing also the phase balancing has an important influence on the effective process window of an alternating PSM. The effective phase error can be measured with an AIMS-system (MSM100). The comparison with simulated data allows the determination of the phase error. In a second step the influence of different balancing methods on phase and transmission were investigated with the TEMPEST mask simulator for unpolarized light. The optimization of the balancing with respect to the CD-bias, undercut and etch depth will be shown and a first approach of a sensitivity analysis will be presented.

  20. Cold Climate Foundation Retrofit Experimental Hygrothermal Performance: Cloquet Residential Research Facility Laboratory Results

    SciTech Connect

    Goldberg, Louise F.; Harmon, Anna C.

    2015-04-01

    Thermal and moisture problems in existing basements create a unique challenge because the exterior face of the wall is not easily or inexpensively accessible. This approach addresses thermal and moisture management from the interior face of the wall without disturbing the exterior soil and landscaping. the interior and exterior environments. This approach has the potential for improving durability, comfort, and indoor air quality. This project was funded jointly by the National Renewable Energy Laboratory (NREL) and Oak Ridge National Laboratory (ORNL). ORNL focused on developing a full basement wall system experimental database to enable others to validate hygrothermal simulation codes. NREL focused on testing the moisture durability of practical basement wall interior insulation retrofit solutions for cold climates. The project has produced a physically credible and reliable long-term hygrothermal performance database for retrofit foundation wall insulation systems in zone 6 and 7 climates that are fully compliant with the performance criteria in the 2009 Minnesota Energy Code. The experimental data were configured into a standard format that can be published online and that is compatible with standard commercially available spreadsheet and database software.

  1. Adaptive wave field synthesis for active sound field reproduction: experimental results.

    PubMed

    Gauthier, Philippe-Aubert; Berry, Alain

    2008-04-01

    Sound field reproduction has applications in music reproduction, spatial audio, sound environment reproduction, and experimental acoustics. Sound field reproduction can be used to artificially reproduce the spatial character of natural hearing. The objective is then to reproduce a sound field in a real reproduction environment. Wave field synthesis (WFS) is a known open-loop technology which assumes that the reproduction environment is anechoic. The room response thus reduces the quality of the physical sound field reproduction by WFS. In recent research papers, adaptive wave field synthesis (AWFS) was defined as a potential solution to compensate for these quality reductions from which WFS objective performance suffers. In this paper, AWFS is experimentally investigated as an active sound field reproduction system with a limited number of reproduction error sensors to compensate for the response of the listening environment. Two digital signal processing algorithms for AWFS are used for comparison purposes, one of which is based on independent radiation mode control. AWFS performed propagating sound field reproduction better than WFS in three tested reproduction spaces (hemianechoic chamber, standard laboratory space, and reverberation chamber). PMID:18397007

  2. Fuel performance under normal PWR conditions: A review of relevant experimental results and models

    NASA Astrophysics Data System (ADS)

    Charles, M.; Lemaignan, C.

    1992-06-01

    Experiments conducted at Grenoble (CEA/DRN) over the past 20 years in the field of nuclear fuel behaviour are reviewed. Of particular concern is the need to achieve a comprehensive understanding of and subsequently overcome the limitations associated with high burnup and load-following conditions (pellet-cladding interaction (PCI), fission gas release (FGR), water-side corrosion). A general view is given of the organization of research work as well as some experimental details (irradiation, postirradiation examination — PIE). Based on various experimental programmes (Cyrano, Medicis, Anemone, Furet, Tango, Contact, Cansar, Hatac, Flog, Decor), the main contributions of the thermomechanical behaviour of a PWR fuel rod are described: thermal conductivity, in-pile densification, swelling, fission gas release in steady state and moderate transient conditions, gap thermal conductance, formation of primary and secondary ridges under PCI conditions. Specific programmes (Gdgrif, Thermox, Grimox) are devoted to the behaviour of particular fuels (gadolinia-bearing fuel, MOX fuel). Moreover, microstructure-based studies have been undertaken on fission gas release (fine analysis of the bubble population inside irradiated fuel samples), and on cladding behaviour (PCI related studies on stress-corrosion cracking (SCO, irradiation effects on zircaloy microstructure).

  3. Direct Numerical Simulation of Liquid Nozzle Spray with Comparison to Shadowgraphy and X-Ray Computed Tomography Experimental Results

    NASA Astrophysics Data System (ADS)

    van Poppel, Bret; Owkes, Mark; Nelson, Thomas; Lee, Zachary; Sowell, Tyler; Benson, Michael; Vasquez Guzman, Pablo; Fahrig, Rebecca; Eaton, John; Kurman, Matthew; Kweon, Chol-Bum; Bravo, Luis

    2014-11-01

    In this work, we present high-fidelity Computational Fluid Dynamics (CFD) results of liquid fuel injection from a pressure-swirl atomizer and compare the simulations to experimental results obtained using both shadowgraphy and phase-averaged X-ray computed tomography (CT) scans. The CFD and experimental results focus on the dense near-nozzle region to identify the dominant mechanisms of breakup during primary atomization. Simulations are performed using the NGA code of Desjardins et al (JCP 227 (2008)) and employ the volume of fluid (VOF) method proposed by Owkes and Desjardins (JCP 270 (2013)), a second order accurate, un-split, conservative, three-dimensional VOF scheme providing second order density fluxes and capable of robust and accurate high density ratio simulations. Qualitative features and quantitative statistics are assessed and compared for the simulation and experimental results, including the onset of atomization, spray cone angle, and drop size and distribution.

  4. Electroluminescence yield for {lambda} > 165 nm in neon-xenon mixtures: Experimental results

    SciTech Connect

    Borges, F.I.G.M.; Santos, J.M.F. dos; Conde, C.A.N.; Kubota, S.

    1996-12-31

    The electroluminescence yield for {lambda} > 165 am in different neon-xenon mixtures is studied as a function of the reduced electric field. These studies were performed using a uniform-field gas proportional scintillation counter. The experimental values obtained for the scintillation and ionization thresholds decrease from approximately 1 and 6 Vcm{sup -1} torr{sup -1} for 100% xenon, to about 0.5 and 3.8 Vcm{sup -1} torr{sup -1} for 20% xenon, to 0.4 and 2.8 Vcm{sup -1} torr{sup -1} for 10% xenon and to 0.3 and 2.2 Vcm{sup -1} torr{sup -1} for 5% xenon. Detector energy resolutions for the Al K line (1.5 keV) are 15% for 20% xenon, 19% for 10% xenon and 22% for 5% xenon.

  5. Experimental results in eddy current nondestructive testing based on superconductive and conventional electromagnetic probes

    SciTech Connect

    Valentino, M.; Ruosi, A.; Pepe, G.; Mollo, V.; D`Alto, R.; Peluso, G.

    1999-04-20

    This paper deals with the electromagnetic nondestructive testing performed by SQUID magnetometry on stratified aluminum alloy plates as those commonly encountered in the aircraft industry. The anomalous magnetic fields generated by flaws wit h known electromagnetic characteristics have been modeled by a three-dimensional specific code based on a finite element formulation. The numerical solution has correctly predicted the shape of the complicated magnetic field response due to the defect. Once accuracy and reliability of experimental data taken by superconductive probe have been tested, a benchmark-like problem has been faced. Measurements performed by conventional probes like fluxgate and inductive coil have been compared with the ones taken by innovative device based on superconductive materials.

  6. Beta decay and the origin of biologial chirality - New experimental results

    NASA Technical Reports Server (NTRS)

    Van House, J.; Rich, A.; Zitzewitz, P. W.

    1984-01-01

    The hypothetical connection developed by Vester and Ulbricht (1959), between the handedness of beta particles in radioactive decay and the (L) sign of biologial chirality is investigated in a radiolysis experiment. The experiment measured the predicted asymmetry in the formation triplet or 'ortho-' positronium (oPs) in amino acid enantiomers by low energy positrons under conditions of helicity reversal. The positrons were focused on amino acid powder samples. By measuring the time between positron arrival and emission of gamma rays, long-lived oPs were separated from other species. It is found that the asymmetry in leucine (0.8 x 10 to the -4th) is consistent with the theoretical prediction of 10 to the -6th. Neither the experimental limits nor the theoretical estimates are found to rule out a mechanism like that described by Vester and Ulbricht as the cause of the sign of the observed chiral polarization.

  7. Experimental and computational ice shapes and resulting drag increase for a NACA 0012 airfoil

    NASA Technical Reports Server (NTRS)

    Shin, Jaiwon; Bond, Thomas H.

    1992-01-01

    Tests were conducted in the Icing Research Tunnel (IRT) at the NASA Lewis Research Center to document the repeatability of the ice shape over the range of temperatures varying from -15 F to 28 F. Measurements of drag increase due to the ice accretion were also made. The ice shape and drag coefficient data, with varying total temperatures at two different airspeeds, were compared with the computational predictions. The calculations were made with the 2D LEWICE/IBL code which is a combined code of LEWICE and the interactive boundary layer method developed for iced airfoils. Comparisons show good agreement with the experimental data in ice shapes. The calculations show the ability of the code to predict drag increases as the ice shape changes from a rime shape to a glaze shape.

  8. Experimental and computational ice shapes and resulting drag increase for a NACA 0012 airfoil

    NASA Technical Reports Server (NTRS)

    Shin, Jaiwon; Bond, Thomas H.

    1992-01-01

    Tests were conducted in the Icing Research Tunnel (IRT) at LeRC to document the repeatability of the ice shape over the range of temperatures varying from -15 to 28 F. Measurements of drag increase due to the ice accretion were also made. The ice shape and drag coefficient data, with varying total temperatures at two different airspeeds, were compared with the computational predictions. The calculations were made with the 2D LEWICE/IBL code which is a combined code of LEWICE and the interactive boundary layer method developed for iced airfoils. Comparisons show good agreement with the experimental data in ice shapes. The calculations show the ability of the code to predict drag increases as the ice shape changes from a rime shape to a glaze shape.

  9. Hyperfine-structure studies of Nb ii: Experimental and relativistic configuration-interaction results

    NASA Astrophysics Data System (ADS)

    Young, L.; Hasegawa, S.; Kurtz, C.; Datta, Debasis; Beck, Donald R.

    1995-05-01

    We report an experimental and theoretical study of the hyperfine structure (hfs) in various metastable states in 93Nb ii. Hyperfine structures of five levels in Nb ii have been measured using a combination of the laser-rf double resonance and laser-induced fluorescence methods in a collinear laser-ion-beam geometry. Theoretically, for J=2, a multireference calculation of energies and hfs based on a relativistic configuration-interaction methodology of the lowest ten levels in the (4d+5s)4 manifold is reported. The average energy error is 450 cm-1. Many of the hyperfine constants show large changes from the Dirac-Fock values and the magnetic dipole constant has a 4% accuracy for the one J=2 level measured. We have also identified all the core-valence and core-core effects that dominate the energy differences and hfs.

  10. First results from solid state neutral particle analyzer on experimental advanced superconducting tokamak

    NASA Astrophysics Data System (ADS)

    Zhang, J. Z.; Zhu, Y. B.; Zhao, J. L.; Wan, B. N.; Li, J. G.; Heidbrink, W. W.

    2016-11-01

    Full function integrated, compact solid state neutral particle analyzers (ssNPA) based on absolute extreme ultraviolet silicon photodiode have been successfully implemented on the experimental advanced superconducting tokamak to measure energetic particle. The ssNPA system has been operated in advanced current mode with fast temporal and spatial resolution capabilities, with both active and passive charge exchange measurements. It is found that the ssNPA flux signals are increased substantially with neutral beam injection (NBI). The horizontal active array responds to modulated NBI beam promptly, while weaker change is presented on passive array. Compared to near-perpendicular beam, near-tangential beam brings more passive ssNPA flux and a broader profile, while no clear difference is observed on active ssNPA flux and its profile. Significantly enhanced intensities on some ssNPA channels have been observed during ion cyclotron resonant heating.

  11. Importance of dose-rate and cell proliferation in the evaluation of biological experimental results

    NASA Technical Reports Server (NTRS)

    Curtis, S. B.

    1994-01-01

    The nuclei of cells within the bodies of astronauts traveling on extended missions outside the geomagnetosphere will experience single traversals of particles with high Linear Energy Transfer (LET) (e.g., one iron ion per one hundred years, on average) superimposed on a background of tracks with low LET (approximately one proton every two to three days, and one helium ion per month). In addition, some cell populations within the body will be proliferating, thus possibly providing increasing numbers of cells with 'initiated' targets for subsequent radiation hits. These temporal characteristics are not generally reproduced in laboratory experimental protocols. Implications of the differences in the temporal patterns of radiation delivery between conventionally designed radiation biology experiments and the pattern to be experienced in space are examined and the importance of dose-rate and cell proliferation are pointed out in the context of radiation risk assessment on long mission in space.

  12. Statistics is not enough: revisiting Ronald A. Fisher's critique (1936) of Mendel's experimental results (1866).

    PubMed

    Pilpel, Avital

    2007-09-01

    This paper is concerned with the role of rational belief change theory in the philosophical understanding of experimental error. Today, philosophers seek insight about error in the investigation of specific experiments, rather than in general theories. Nevertheless, rational belief change theory adds to our understanding of just such cases: R. A. Fisher's criticism of Mendel's experiments being a case in point. After an historical introduction, the main part of this paper investigates Fisher's paper from the point of view of rational belief change theory: what changes of belief about Mendel's experiment does Fisher go through and with what justification. It leads to surprising insights about what Fisher had done right and wrong, and, more generally, about the limits of statistical methods in detecting error.

  13. Importance of dose-rate and cell proliferation in the evaluation of biological experimental results.

    PubMed

    Curtis, S B

    1994-01-01

    The nuclei of cells within the bodies of astronauts traveling on extended missions outside the geomagnetosphere will experience single traversals of particles with high LET (e.g., one iron ion per one hundred years, on average) superimposed on a background of tracks with low LET (approximately one proton every two to three days, and one helium ion per month). In addition, some cell populations within the body will be proliferating, thus possibly providing increasing numbers of cells with "initiated" targets for subsequent radiation hits. These temporal characteristics are not generally reproduced in laboratory experimental protocols. Implications of the differences in the temporal patterns of radiation delivery between conventionally designed radiation biology experiments and the pattern to be experienced in space are examined and the importance of dose-rate and cell proliferation are pointed out in the context of radiation risk assessment on long missions in space. PMID:11538040

  14. Validation data for photochemical mechanisms: experimental results. Interim report, April 1986-December 1987

    SciTech Connect

    Sexton, K.G.; Arnold, J.R.; Jeffries, H.E.; Kale, T.L.; Kamens, R.M.

    1988-11-01

    The smog-chamber facility of the University of North Carolina (UNC) was used to provide experimental data for the EPA and atmospheric model developers for testing and validating kinetic mechanisms of photochemical smog formation. In the study, 71 dual experiments were performed using NOx and various hydrocarbons and hydrocarbon mixtures. Experiments were also conducted to better understand and characterize (1) the chamber when operated dynamically to simulate continuous emissions and dilution, and (2) the solar radiation inside the smog chamber. The chamber experiments described in the report were added to the existing UNC data base for model testing, bringing the total number of dual experiments in the data base to 417. The data base is available on an ANSI-formatted magnetic tape.

  15. Phase shifts in the EXAFS of crystalline iron-experimental results and theoretical calculations

    NASA Astrophysics Data System (ADS)

    Zschech, E.; Rennert, P.

    1989-10-01

    For crystalline iron, it has been shown that the approximation of the spherical photoelectron wave by a plane wave causes systematic errors. Shell-dependent energy shifts E0 up to 10 eV are necessary to correct these errors of the plane-wave SSCA (small-scattering-centre approximation). An analytical expression E0( R) is given which can be used as preinformation in the analysis of an experimental EXAFS spectrum. Consequently, the great number of free parameters, especially the "dummy" energy zeros for different coordination shells at a distance R, can be reduced drastically. Furthermore, two approximations within the curved-wave theory, MSSCA (modified small-scattering-centre approximation) and RAME (reduced angular momentum expansion), that partially correct the systematic E0 errors are proposed.

  16. Investigation of superelastic electron scattering by laser-excited Ba - Experimental procedures and results

    NASA Technical Reports Server (NTRS)

    Register, D. F.; Trajmar, S.; Fineman, M. A.; Poe, R. T.; Csanak, G.; Jensen, S. W.

    1983-01-01

    Differential (in angle) electron scattering experiments on laser-excited Ba-138 1P were carried out at 30- and 100-eV impact energies. The laser light was linearly polarized and located in the scattering plane. The superelastic scattering signal was measured as a function of polarization direction of the laser light with respect to the scattering plane. It was found at low electron scattering angles that the superelastic scattering signal was asymmetric to reflection of the polarization vector with respect to the scattering plane. This is in contradiction with theoretical predictions. An attempt was made to pinpoint the reason for this observation, and a detailed investigation of the influence of experimental conditions on the superelastic scattering was undertaken. No explanation for the asymmetry has as yet been found.

  17. The experimental results of a self tuning adaptive controller using online frequency identification. [for Galileo spacecraft

    NASA Technical Reports Server (NTRS)

    Chiang, W.-W.; Cannon, R. H., Jr.

    1985-01-01

    A fourth-order laboratory dynamic system featuring very low structural damping and a noncolocated actuator-sensor pair has been used to test a novel real-time adaptive controller, implemented in a minicomputer, which consists of a state estimator, a set of state feedback gains, and a frequency-locked loop for real-time parameter identification. The adaptation algorithm employed can correct controller error and stabilize the system for more than 50 percent variation in the plant's natural frequency, compared with a 10 percent stability margin in frequency variation for a fixed gain controller having the same performance as the nominal plant condition. The very rapid convergence achievable by this adaptive system is demonstrated experimentally, and proven with simple, root-locus methods.

  18. [Ex-vivo expansion of cornea stem cells. Experimental principles and initial clinical results].

    PubMed

    Meller, D; Kruse, F

    2001-09-01

    The ocular surface epithelium is composed of conjunctiva, limbus and cornea. These three compartments and an stable preocular tear film are crucial factors determining ocular surface health. Stem cells of the corneal epithelium are exclusively located at the limbus. Limbal stem cells are the ultimate source of regeneration of the entire corneal epithelium and in a variety of ocular surface diseases limbal stem cell deficiency has been observed to be a characteristic feature. Therefore renewal of the limbal stem cell population using different surgical techniques has been described as the only possible therapeutic strategy. Recent advancements in cell biology have enabled the development of new models of tissue engineering as a tool for tissue replacement. The aim of this review is to summarize recently reported clinical and experimental studies showing new developments in tissue engineering for the reconstitution of the ocular surface epithelium. PMID:11594220

  19. Performance of the Argonne Wakefield Accelerator Facility and initial experimental results

    SciTech Connect

    Gai, W.; Conde, M.; Cox, G.; Konecny, R.; Power, J.; Schoessow, P.; Simpson, J.; Barov, N.

    1996-10-01

    The Argonne Wakefield Accelerator facility has begun its experimental program. It is designed to address advanced acceleration research requiring very short, intense electron bunches. It incorporates two photocathode based electron sources. One produces up to 100 nC, multi-kiloamp `drive` bunches which are used to excite wakefields in dielectric loaded structures and in plasma. The second source produces much lower intensity `witness` pulses which are used to probe the fields produced by the drive. The drive and witness pulses can be precisely timed as well as laterally positioned with respect to each other. This paper discusses commissioning, initial experiments, and outline plans for a proposed 1 GeV demonstration accelerator.

  20. Experimental results from a DC photocathode electron gun for an IR FEL

    SciTech Connect

    Kehne, D.; Engwall, D.; Legg, R.; Shinn, M.

    1997-10-01

    A 350 keV DC photocathode gun capable of delivering the high-brightness CW electron beam necessary for Jefferson Lab`s infrared free-electron laser is described. The gun is to be used with a superconducting radiofrequency linac operating at 1.497 GHz and is mode-locked to the 40th subharmonic of the fundamental using a Nd:YLF drive laser. The gun provides 20--25 ps bunches at up to 135 pC/bunch. Experimental measurements of transverse and longitudinal beam properties are presented. Transverse emittance is measured using a slit-wire scanner emittance meter, and energy spread is measured using the slit and a spectrometer magnet. Longitudinal emittance is measured using a combination of sampling aperture, kicker cavity, slit and spectrometer. Measurements for bunch charges of 135 pC are described and compared with simulations.

  1. Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

    SciTech Connect

    Zhang, Jinsuo

    2008-01-01

    Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

  2. Binding of small basic peptides to membranes containing acidic lipids: theoretical models and experimental results.

    PubMed Central

    Ben-Tal, N; Honig, B; Peitzsch, R M; Denisov, G; McLaughlin, S

    1996-01-01

    We measured directly the binding of Lys3, Lys5, and Lys7 to vesicles containing acidic phospholipids. When the vesicles contain 33% acidic lipids and the aqueous solution contains 100 mM monovalent salt, the standard Gibbs free energy for the binding of these peptides is 3, 5, and 7 kcal/mol, respectively. The binding energies decrease as the mol% of acidic lipids in the membrane decreases and/or as the salt concentration increases. Several lines of evidence suggest that these hydrophilic peptides do not penetrate the polar headgroup region of the membrane and that the binding is mainly due to electrostatic interactions. To calculate the binding energies from classical electrostatics, we applied the nonlinear Poisson-Boltzmann equation to atomic models of the phospholipid bilayers and the basic peptides in aqueous solution. The electrostatic free energy of interaction, which arises from both a long-range coulombic attraction between the positively charged peptide and the negatively charged lipid bilayer, and a short-range Born or image charge repulsion, is a minimum when approximately 2.5 A (i.e., one layer of water) exists between the van der Waals surfaces of the peptide and the lipid bilayer. The calculated molar association constants, K, agree well with the measured values: K is typically about 10-fold smaller than the experimental value (i.e., a difference of about 1.5 kcal/mol in the free energy of binding). The predicted dependence of K (or the binding free energies) on the ionic strength of the solution, the mol% of acidic lipids in the membrane, and the number of basic residues in the peptide agree very well with the experimental measurements. These calculations are relevant to the membrane binding of a number of important proteins that contain clusters of basic residues. Images FIGURE 2 FIGURE 3 PMID:8842196

  3. Presentation of clinical laboratory results: an experimental comparison of four visualization techniques

    PubMed Central

    Torsvik, Torbjørn; Lillebo, Børge; Mikkelsen, Gustav

    2013-01-01

    Objective To evaluate how clinical chemistry test results were assessed by volunteers when presented with four different visualization techniques. Materials and methods A total of 20 medical students reviewed quantitative test results from 4 patients using 4 different visualization techniques in a balanced, crossover experiment. The laboratory data represented relevant patient categories, including simple, emergency, chronic and complex patients. Participants answered questions about trend, overall levels and covariation of test results. Answers and assessment times were recorded and participants were interviewed on their preference of visualization technique. Results Assessment of results and the time used varied between visualization techniques. With sparklines and relative multigraphs participants made faster assessments. With relative multigraphs participants identified more covarying test results. With absolute multigraphs participants found more trends. With sparklines participants more often assessed laboratory results to be within reference ranges. Different visualization techniques were preferred for the four different patient categories. No participant preferred absolute multigraphs for any patient. Discussion Assessments of clinical chemistry test results were influenced by how they were presented. Importantly though, this association depended on the complexity of the result sets, and none of the visualization techniques appeared to be ideal in all settings. Conclusions Sparklines and relative multigraphs seem to be favorable techniques for presenting complex long-term clinical chemistry test results, while tables seem to suffice for simpler result sets. PMID:23043123

  4. Micronozzles: 3D numerical structural and gas dynamics modeling, fabrication, and preliminary experimental results

    NASA Astrophysics Data System (ADS)

    Borovkov, Alexei I.; Pyatishev, Evgenij N.; Lurie, Mihail S.; Korshunov, Andrey V.; Akulshin, Y. D.; Dolganov, A. G.; Sabadash, V. O.

    2000-02-01

    The tiny engines, founded on the principle of reactive thrust, are one of most perspective actuators developed by modern micromechanics. These engines can be applied for such apparent problems, as orientation and stabilization of small space objects, but also as local or distributed reactive thrust of new phylum of aerospace objects, for control of boundary layer of flying objects and in series of converting power devices of different purposes. Distinctive features of jet tiny engines are profitability (very large thrust-to-weight ratio) and high (milliseconds) response, which makes them to irreplaceable elements in control systems and, specially, in distributed power generations. These features are provided the minimum sizes, high pressure in working chambers and hypersonic velocity of propulsive jet. Topologically micronozzles are designed as the flat batch devices (3 layers as minimum). The lower and upper layers make flat walls of the nozzle and mainly influence on strength properties of the device. The mean layer reshapes geometry and determines gas dynamic characteristic of the nozzle. A special problem is the opening-up of the combustion-mixture, which is not esteemed in this work. It is necessary to allow for effect of considerable local stresses arising at the expense of static and dynamic loading at design of the jet tiny engines. Thermal gas dynamic processes in the chamber and nozzle determine the values and nature of these stresses, which are hardly studied for the microdevices. The priority is mathematical and experimental simulation of these processes. The most suitable object for initial phase of experimental simulation is the 'cold' engine. The demanded chamber static pressure is formed by external compressed air. In Laboratory of Microtechnology and MicroElectroMechanical Systems a number of such tiny engines with different shapes of the chamber's and the nozzles' surfaces were designed, made and tested. The engines were produced from photosensing

  5. Micronozzles: 3D numerical structural and gas dynamics modeling, fabrication, and preliminary experimental results

    NASA Astrophysics Data System (ADS)

    Borovkov, Alexei I.; Pyatishev, Evgenij N.; Lurie, Mihail S.; Korshunov, Andrey V.; Akulshin, Y. D.; Dolganov, A. G.; Sabadash, V. O.

    2001-02-01

    The tiny engines, founded on the principle of reactive thrust, are one of most perspective actuators developed by modern micromechanics. These engines can be applied for such apparent problems, as orientation and stabilization of small space objects, but also as local or distributed reactive thrust of new phylum of aerospace objects, for control of boundary layer of flying objects and in series of converting power devices of different purposes. Distinctive features of jet tiny engines are profitability (very large thrust-to-weight ratio) and high (milliseconds) response, which makes them to irreplaceable elements in control systems and, specially, in distributed power generations. These features are provided the minimum sizes, high pressure in working chambers and hypersonic velocity of propulsive jet. Topologically micronozzles are designed as the flat batch devices (3 layers as minimum). The lower and upper layers make flat walls of the nozzle and mainly influence on strength properties of the device. The mean layer reshapes geometry and determines gas dynamic characteristic of the nozzle. A special problem is the opening-up of the combustion-mixture, which is not esteemed in this work. It is necessary to allow for effect of considerable local stresses arising at the expense of static and dynamic loading at design of the jet tiny engines. Thermal gas dynamic processes in the chamber and nozzle determine the values and nature of these stresses, which are hardly studied for the microdevices. The priority is mathematical and experimental simulation of these processes. The most suitable object for initial phase of experimental simulation is the 'cold' engine. The demanded chamber static pressure is formed by external compressed air. In Laboratory of Microtechnology and MicroElectroMechanical Systems a number of such tiny engines with different shapes of the chamber's and the nozzles' surfaces were designed, made and tested. The engines were produced from photosensing

  6. Experimental results of a new system using microwaves for vision correction

    NASA Astrophysics Data System (ADS)

    Ryan, Thomas P.; Pertaub, Radha; Meyers, Steven R.; Dresher, Russell P.; Scharf, Ronald

    2009-02-01

    Technology is in development to correct vision without the use of lasers or cutting of the eye. Many current technologies used to reshape the cornea are invasive, in that either RF needles are placed into the cornea or a flap is cut and then a laser used to ablate the cornea in the optical zone. Keraflex, a therapeutic microwave treatment, is a noninvasive, non-incisional refractive surgery procedure capable of treating myopia (nearsightedness). The goal is to create a predictable refractive change in the optical zone, while preserving the epithelium and deeper structures of the eye. A further goal is to avoid incisions and damage to the epithelium which both require a post-treatment healing period. Experimental work with fresh porcine eyes examined the following variables: duration of the RF pulse, RF power level, coolant amount and timing, electrode spacing, applanation force against the eye, initial eye temperature, and age of eye. We measured curvature changes of the eye with topography, Scheimpflug, Wavefront aberrometry or other means to characterize diopter change as an important endpoint. Other assessment includes evaluation of a fine white ring seen in the cornea following treatment. Dose studies have been done to correlate the treated region with energy delivered. The timing and dosing of energy and cooling were investigated to achieve the target diopter change in vision.

  7. Sound absorption of porous substrates covered by foliage: experimental results and numerical predictions.

    PubMed

    Ding, Lei; Van Renterghem, Timothy; Botteldooren, Dick; Horoshenkov, Kirill; Khan, Amir

    2013-12-01

    The influence of loose plant leaves on the acoustic absorption of a porous substrate is experimentally and numerically studied. Such systems are typical in vegetative walls, where the substrate has strong acoustical absorbing properties. Both experiments in an impedance tube and theoretical predictions show that when a leaf is placed in front of such a porous substrate, its absorption characteristics markedly change (for normal incident sound). Typically, there is an unaffected change in the low frequency absorption coefficient (below 250 Hz), an increase in the middle frequency absorption coefficient (500-2000 Hz) and a decrease in the absorption at higher frequencies. The influence of leaves becomes most pronounced when the substrate has a low mass density. A combination of the Biot's elastic frame porous model, viscous damping in the leaf boundary layers and plate vibration theory is implemented via a finite-difference time-domain model, which is able to predict accurately the absorption spectrum of a leaf above a porous substrate system. The change in the absorption spectrum caused by the leaf vibration can be modeled reasonably well assuming the leaf and porous substrate properties are uniform.

  8. Modeling and experimental results for condensing supercritical CO2 power cycles.

    SciTech Connect

    Wright, Steven Alan; Conboy, Thomas M.; Radel, Ross F.; Rochau, Gary Eugene

    2011-01-01

    This Sandia supported research project evaluated the potential improvement that 'condensing' supercritical carbon dioxide (S-CO{sub 2}) power cycles can have on the efficiency of Light Water Reactors (LWR). The analytical portion of research project identified that a S-CO{sub 2} 'condensing' re-compression power cycle with multiple stages of reheat can increase LWR power conversion efficiency from 33-34% to 37-39%. The experimental portion of the project used Sandia's S-CO{sub 2} research loop to show that the as designed radial compressor could 'pump' liquid CO{sub 2} and that the gas-cooler's could 'condense' CO{sub 2} even though both of these S-CO{sub 2} components were designed to operate on vapor phase S-CO{sub 2} near the critical point. There is potentially very high value to this research as it opens the possibility of increasing LWR power cycle efficiency, above the 33-34% range, while lowering the capital cost of the power plant because of the small size of the S-CO{sub 2} power system. In addition it provides a way to incrementally build advanced LWRs that are optimally designed to couple to S-CO{sub 2} power conversion systems to increase the power cycle efficiency to near 40%.

  9. James Webb Space Telescope optical simulation testbed III: first experimental results with linear-control alignment

    NASA Astrophysics Data System (ADS)

    Egron, Sylvain; Lajoie, Charles-Philippe; Leboulleux, Lucie; N'Diaye, Mamadou; Pueyo, Laurent; Choquet, Élodie; Perrin, Marshall D.; Ygouf, Marie; Michau, Vincent; Bonnefois, Aurélie; Fusco, Thierry; Escolle, Clément; Ferrari, Marc; Hugot, Emmanuel; Soummer, Rémi

    2016-07-01

    The James Webb Space Telescope (JWST) Optical Simulation Testbed (JOST) is a tabletop experiment designed to study wavefront sensing and control for a segmented space telescope, including both commissioning and maintenance activities. JOST is complementary to existing testbeds for JWST (e.g. the Ball Aerospace Testbed Telescope TBT) given its compact scale and flexibility, ease of use, and colocation at the JWST Science and Operations Center. The design of JOST reproduces the physics of JWST's three-mirror anastigmat (TMA) using three custom aspheric lenses. It provides similar quality image as JWST (80% Strehl ratio) over a field equivalent to a NIRCam module, but at 633 nm. An Iris AO segmented mirror stands for the segmented primary mirror of JWST. Actuators allow us to control (1) the 18 segments of the segmented mirror in piston, tip, tilt and (2) the second lens, which stands for the secondary mirror, in tip, tilt and x, y, z positions. We present the full linear control alignment infrastructure developed for JOST, with an emphasis on multi-field wavefront sensing and control. Our implementation of the Wavefront Sensing (WFS) algorithms using phase diversity is experimentally tested. The wavefront control (WFC) algorithms, which rely on a linear model for optical aberrations induced by small misalignments of the three lenses, are tested and validated on simulations.

  10. Experimental Results of Underwater Cooperative Source Localization Using a Single Acoustic Vector Sensor

    PubMed Central

    Felisberto, Paulo; Rodriguez, Orlando; Santos, Paulo; Ey, Emanuel; Jesus, Sérgio M.

    2013-01-01

    This paper aims at estimating the azimuth, range and depth of a cooperative broadband acoustic source with a single vector sensor in a multipath underwater environment, where the received signal is assumed to be a linear combination of echoes of the source emitted waveform. A vector sensor is a device that measures the scalar acoustic pressure field and the vectorial acoustic particle velocity field at a single location in space. The amplitudes of the echoes in the vector sensor components allow one to determine their azimuth and elevation. Assuming that the environmental conditions of the channel are known, source range and depth are obtained from the estimates of elevation and relative time delays of the different echoes using a ray-based backpropagation algorithm. The proposed method is tested using simulated data and is further applied to experimental data from the Makai'05 experiment, where 8–14 kHz chirp signals were acquired by a vector sensor array. It is shown that for short ranges, the position of the source is estimated in agreement with the geometry of the experiment. The method is low computational demanding, thus well-suited to be used in mobile and light platforms, where space and power requirements are limited. PMID:23857257

  11. Experimental Results in Support of Simulating Progressive Crush in Carbon-Fiber Textile Composites

    SciTech Connect

    DeTeresa, S J; Allison, L M; Cunningham, B J; Freeman, DC; Saculla, M D; Sanchez, R J; Winchester, S W

    2001-04-02

    This report summarizes the findings of an experimental program conducted to support the modeling of the crush behavior of triaxial braid carbon fiber composites. The matrix material as well as braided panels and tubes were characterized in order to determine material properties, to assess failure modes, and to provide a test bed for new analytical and numerical tools developed specifically for braided composites. The matrix material selected by the ACC was an epoxy vinyl ester (Ashland Hetron 922). Tensile tests were used to compare two formulations-one used by the ACC and one recommended by the resin supplier. The latter was a faster reacting system and gelled in one-third the time of the ACC formulation. Both formulations had an average elongation at failure that was only half of the resin supplier's reported value. Only one specimen of each type came close to the reported elongation value and it was shown that failure invariably initiated at both surface and internal defects. Overall, the tensile properties of the two formulations were nearly identical, but those of the ACC system were more consistent. The properties of the ACC matrix formulation were measured in tension, shear, and compression and the average properties obtained in these tests are summarized.

  12. Experimental cavity pressure measurements at subsonic and transonic speeds. Static-pressure results

    NASA Technical Reports Server (NTRS)

    Plentovich, E. B.; Stallings, Robert L., Jr.; Tracy, M. B.

    1993-01-01

    An experimental investigation was conducted to determine cavity flow-characteristics at subsonic and transonic speeds. A rectangular box cavity was tested in the Langley 8-Foot Transonic Pressure Tunnel at Mach numbers from 0.20 to 0.95 at a unit Reynolds number of approximately 3 x 10(exp 6) per foot. The boundary layer approaching the cavity was turbulent. Cavities were tested over a range of length-to-depth ratios (l/h) of 1 to 17.5 for cavity width-to-depth ratios of 1, 4, 8, and 16. Fluctuating- and static-pressure data in the cavity were obtained; however, only static-pressure data is analyzed. The boundaries between the flow regimes based on cavity length-to-depth ratio were determined. The change to transitional flow from open flow occurs at l/h at approximately 6-8 however, the change from transitional- to closed-cavity flow occurred over a wide range of l/h and was dependent on Mach number and cavity configuration. The change from closed to open flow as found to occur gradually. The effect of changing cavity dimensions showed that if the vlaue of l/h was kept fixed but the cavity width was decreased or cavity height was increased, the cavity pressure distribution tended more toward a more closed flow distribution.

  13. Concept of operation and preliminary experimental results of the DRDC through-wall SAR system

    NASA Astrophysics Data System (ADS)

    Sévigny, Pascale; DiFilippo, David J.; Laneve, Tony; Chan, Brigitte; Fournier, Jonathan; Roy, Simon; Ricard, Benoît; Maheux, Jean

    2010-04-01

    Mapping the interior of buildings is of great interest to military forces operating in an urban battlefield. Throughwall radars have the potential of mapping interior room layout, including the location of walls, doors and furniture. They could provide information on the in-wall structure, and detect objects of interest concealed in buildings, such as persons and arms caches. We are proposing to provide further context to the end user by fusing the radar data with LIDAR (Light Detection and Ranging) images of the building exterior. In this paper, we present our system concept of operation, which involves a vehicle driven along a path in front of a building of interest. The vehicle is equipped with both radar and LIDAR systems, as well as a motion compensation unit. We describe our ultra wideband through-wall L-band radar system which uses stretch processing techniques to obtain high range resolution, and synthetic aperture radar (SAR) techniques to achieve good azimuth resolution. We demonstrate its current 2-D capabilities with experimental data, and discuss the current progress in using array processing in elevation to provide a 3-D image. Finally, we show preliminary data fusion of SAR and LIDAR data.

  14. Some experimental and theoretical results on the anodic patterns in plasma discharge

    SciTech Connect

    Gurlui, S.; Agop, M.; Strat, M.; Strat, Georgeta; Bacaita, Simona; Cerepaniuc, Adina

    2006-06-15

    The dynamics of an interface plasma-plasma self-structured as a double anodic layer using the fractal space-time theory is established. So, for the fractal dimension D=2, the Schroedinger 'fluid' is obtained as an irrotational movement of a Navier-Stokes fluid with an imaginary viscosity coefficient. In the deterministic case, the anodic double layer is described by a set of diffusion-reaction equations, a situation in which the equal diffusion curves are of the Koch-type and the self-structuring is given by means of the coherence of the electron-ion pairs. In the nondeterministic case, the anodic double layer is described by a set of time-dependent Schroedinger-type equations and the self-structuring is given by means of the negative differential resistance and the pulsation-potential linear dependence. Through the spontaneous symmetry breaking the Langmuir's relations, the distributions of the potential field and charge densities have been obtained. The model was verified by means of our experimental data too.

  15. Preliminary results of experimental measurements to determine microparticle charge in a complex plasma

    NASA Astrophysics Data System (ADS)

    Gillman, Eric; Amatucci, Bill

    2015-09-01

    Microparticles in a dusty plasma typically collect many of the more mobile electrons as they charge up and therefore typically attain a net negative potential. The charge on these microparticles is typically estimated by calculating the charge on a spherical capacitor at the floating potential or by making measurements of particles levitating in the plasma sheath. However, secondary processes can alter the charging process and are significantly altered in the plasma sheath. Currently there is no reliable method to measure microparticle surface charge in the bulk region of complex or dusty plasmas. A novel, non-invasive, experimental method of measuring the charging of microparticles in the bulk region of a plasma will be presented. Ions impinging directly upon the microparticle surface and interacting electrostatically with the charged microparticle, known as collisional and electrostatic Coulomb ion drag, respectively, slows particle acceleration due to gravity as the particle falls through a plasma discharge. Since ion and neutral drag are commonly the dominant forces on microparticles in complex plasmas, the reduced acceleration is measured without a plasma to determine the neutral drag. By repeating the measurement with a plasma and subtracting the neutral drag, the ion drag is obtained. The microparticle net charge is then ascertained from the ion drag on isolated grains falling through a plasma discharge. This work was supported by the Naval Research Laboratory Base Program.

  16. Nonconventional control of the flexible pole-cart balancing problem: Experimental results.

    PubMed

    Dadios, E P; Williams, D J

    1998-01-01

    Emerging techniques of intelligent or learning control seem attractive for applications in manufacturing and robotics. It is however important to understand the capabilities of such control systems. In the past the inverted pendulum has been used as a test case, however, this problem is not sufficiently testing. This research therefore concentrates on the control of the inverted pendulum with additional degrees of freedom as a testing demonstrator problem for learning control system experimentation. A flexible pole is used in place of a rigid one. The transverse displacement of the flexible pole has distributed elasticity and therefore infinite degrees of freedom. The dynamics of this new system are more complex as the system needs additional parameters to be defined due to the pole's elastic deflection. This problem also has many of the significant features associated with flexible robots with lightweight links as applied in manufacturing. Novel neural network and fuzzy control systems are presented that control such a system in real time in one of its modes of vibration. A fuzzy-genetic approach is also demonstrated that allows the creation of fuzzy control systems without the use of extensive knowledge.

  17. Theoretical investigation of second hyperpolarizability of trans-polyacetylene: Comparison between experimental and theoretical results for small oligomers

    NASA Astrophysics Data System (ADS)

    Andrade, Ageo Meier de; Inacio, Patrícia Loren; Camilo, Alexandre

    2015-12-01

    The development of new conductive polymers nowadays is one of the most important technological areas in materials design. Computational investigation of desired properties in conductive polymers could save financial resources and time, but it is important to choose the methodology that produces good results comparing to experimental results. To verify the prediction of second hyperpolarizability (γ) in oligomers of Trans-Polyacetylene (TPA) by theoretical calculations, a series of semi-empirical, Hartree-Fock (HF), and Density Functional Theory (DFT) calculations were performed and analysed through linear fitting statistical analysis to investigate the accuracy of such theoretical predictions in comparison to the experimental ones. The results showed that HF and DFT methodologies do not describe γ with good accuracy, but the use of diffuse and polarizability functions in HF methodology provided better results than 3-21G and 6-31G functions. It was concluded that RM1 methodology better agrees with γ experimental results for TPA oligomers, and linear fitting statistical analysis is a useful tool to compare experimental and theoretical results.

  18. Subliminal psychodynamic activation: updated comprehensive list of experimental results and comments on previous lists.

    PubMed

    Fudin, R; Benjamin, C

    1992-06-01

    A comprehensive list of results from visual subliminal psychodynamic activation experiments is presented. This list includes results reported since the publication of the last comprehensive list by Weinberger and Hardaway in 1990 and several results not found on that list. On the present list, SPA results are categorized according to criteria that we contend are more objective than those used previously. In contrast to conclusions drawn from previous lists prepared by Silverman in 1980 and 1983, by Weinberger and Hardaway in 1990, and by Weinberger and Silverman in 1987, the present list indicates that the results of a majority of experiments do not clearly support hypotheses tested by the subliminal psychodynamic activation method. Aspects of Hardaway's meta-analyses from 1987 and 1990 for major areas of research on subliminal psychodynamic activation are discussed in terms of suggestions for further research. PMID:1608734

  19. Macrophage activation associated with chronic murine cytomegalovirus infection results in more severe experimental choroidal neovascularization.

    PubMed

    Cousins, Scott W; Espinosa-Heidmann, Diego G; Miller, Daniel M; Pereira-Simon, Simone; Hernandez, Eleut P; Chien, Hsin; Meier-Jewett, Courtney; Dix, Richard D

    2012-01-01

    The neovascular (wet) form of age-related macular degeneration (AMD) leads to vision loss due to choroidal neovascularization (CNV). Since macrophages are important in CNV development, and cytomegalovirus (CMV)-specific IgG serum titers in patients with wet AMD are elevated, we hypothesized that chronic CMV infection contributes to wet AMD, possibly by pro-angiogenic macrophage activation. This hypothesis was tested using an established mouse model of experimental CNV. At 6 days, 6 weeks, or 12 weeks after infection with murine CMV (MCMV), laser-induced CNV was performed, and CNV severity was determined 4 weeks later by analysis of choroidal flatmounts. Although all MCMV-infected mice exhibited more severe CNV when compared with control mice, the most severe CNV developed in mice with chronic infection, a time when MCMV-specific gene sequences could not be detected within choroidal tissues. Splenic macrophages collected from mice with chronic MCMV infection, however, expressed significantly greater levels of TNF-α, COX-2, MMP-9, and, most significantly, VEGF transcripts by quantitative RT-PCR assay when compared to splenic macrophages from control mice. Direct MCMV infection of monolayers of IC-21 mouse macrophages confirmed significant stimulation of VEGF mRNA and VEGF protein as determined by quantitative RT-PCR assay, ELISA, and immunostaining. Stimulation of VEGF production in vivo and in vitro was sensitive to the antiviral ganciclovir. These studies suggest that chronic CMV infection may serve as a heretofore unrecognized risk factor in the pathogenesis of wet AMD. One mechanism by which chronic CMV infection might promote increased CNV severity is via stimulation of macrophages to make pro-angiogenic factors (VEGF), an outcome that requires active virus replication. PMID:22570607

  20. Macrophage Activation Associated with Chronic Murine Cytomegalovirus Infection Results in More Severe Experimental Choroidal Neovascularization

    PubMed Central

    Cousins, Scott W.; Espinosa-Heidmann, Diego G.; Miller, Daniel M.; Pereira-Simon, Simone; Hernandez, Eleut P.; Chien, Hsin; Meier-Jewett, Courtney; Dix, Richard D.

    2012-01-01

    The neovascular (wet) form of age-related macular degeneration (AMD) leads to vision loss due to choroidal neovascularization (CNV). Since macrophages are important in CNV development, and cytomegalovirus (CMV)-specific IgG serum titers in patients with wet AMD are elevated, we hypothesized that chronic CMV infection contributes to wet AMD, possibly by pro-angiogenic macrophage activation. This hypothesis was tested using an established mouse model of experimental CNV. At 6 days, 6 weeks, or 12 weeks after infection with murine CMV (MCMV), laser-induced CNV was performed, and CNV severity was determined 4 weeks later by analysis of choroidal flatmounts. Although all MCMV-infected mice exhibited more severe CNV when compared with control mice, the most severe CNV developed in mice with chronic infection, a time when MCMV-specific gene sequences could not be detected within choroidal tissues. Splenic macrophages collected from mice with chronic MCMV infection, however, expressed significantly greater levels of TNF-α, COX-2, MMP-9, and, most significantly, VEGF transcripts by quantitative RT-PCR assay when compared to splenic macrophages from control mice. Direct MCMV infection of monolayers of IC-21 mouse macrophages confirmed significant stimulation of VEGF mRNA and VEGF protein as determined by quantitative RT-PCR assay, ELISA, and immunostaining. Stimulation of VEGF production in vivo and in vitro was sensitive to the antiviral ganciclovir. These studies suggest that chronic CMV infection may serve as a heretofore unrecognized risk factor in the pathogenesis of wet AMD. One mechanism by which chronic CMV infection might promote increased CNV severity is via stimulation of macrophages to make pro-angiogenic factors (VEGF), an outcome that requires active virus replication. PMID:22570607

  1. CO2 utilization and storage in shale gas reservoirs: Experimental results and economic impacts

    DOE PAGES

    Schaef, Herbert T.; Davidson, Casie L.; Owen, Antionette Toni; Miller, Quin R. S.; Loring, John S.; Thompson, Christopher J.; Bacon, Diana H.; Glezakou, Vassiliki Alexandra; McGrail, B. Peter

    2014-12-31

    Natural gas is considered a cleaner and lower-emission fuel than coal, and its high abundance from advanced drilling techniques has positioned natural gas as a major alternative energy source for the U.S. However, each ton of CO2 emitted from any type of fossil fuel combustion will continue to increase global atmospheric concentrations. One unique approach to reducing anthropogenic CO2 emissions involves coupling CO2 based enhanced gas recovery (EGR) operations in depleted shale gas reservoirs with long-term CO2 storage operations. In this paper, we report unique findings about the interactions between important shale minerals and sorbing gases (CH4 and CO2) andmore » associated economic consequences. Where enhanced condensation of CO2 followed by desorption on clay surface is observed under supercritical conditions, a linear sorption profile emerges for CH4. Volumetric changes to montmorillonites occur during exposure to CO2. Theory-based simulations identify interactions with interlayer cations as energetically favorable for CO2 intercalation. Thus, experimental evidence suggests CH4 does not occupy the interlayer and has only the propensity for surface adsorption. Mixed CH4:CO2 gas systems, where CH4 concentrations prevail, indicate preferential CO2 sorption as determined by in situ infrared spectroscopy and X-ray diffraction techniques. Collectively, these laboratory studies combined with a cost-based economic analysis provide a basis for identifying favorable CO2-EOR opportunities in previously fractured shale gas reservoirs approaching final stages of primary gas production. Moreover, utilization of site-specific laboratory measurements in reservoir simulators provides insight into optimum injection strategies for maximizing CH4/CO2 exchange rates to obtain peak natural gas production.« less

  2. Performances and first experimental results of BACH, the beamline for dichroism and scattering experiments at ELETTRA

    SciTech Connect

    Zangrando, M.; Zacchigna, M.; Bondino, F.; Finazzi, M.; Pardini, T.; Plate, M.; Rochow, R.; Cocco, D.; Parmigiani, F.

    2004-05-12

    BACH, the new soft x-ray beamline for polarization dependent experiments at the Italian synchrotron radiation facility ELETTRA, has been commissioned, characterized and opened to external users. Based on two APPLE II undulators, it covers an energy range between 35 eV and 1600 eV with the control of the light polarization. The monochromator works either in high resolution or high flux mode. Resolving powers of 16000 at 50 eV, 12000 at 90 eV, more than 12000 at 400 eV, 15000 at 534 eV and 6600 at 867 eV have been achieved with the three high resolution gratings. The resolving powers of the high flux grating, which covers the 290 - 1600 eV range, have been measured reaching 7000 at 400 eV and 2200 at 867 eV. The fluxes, in the high resolution mode, range between 4{center_dot}1011 photons/s at 125 eV and 2{center_dot}1010 photons/s at about 1100 eV. Using the high flux grating with the best resolution achievable 1.7{center_dot}1011 photons/s impinge on the sample at 900 eV. Two branches are installed after the monochromator allowing the set-up of two different experimental stations. One of them, besides several facilities for surface preparation and analysis, hosts a compact inelastic soft x-ray spectrometer (ComIXS) dedicated to x-ray emission experiments exploiting the small spot (10 {mu}m in the vertical direction) on the sample. The other branch hosts a liquid helium cryostat equipped with a superconducting coil to perform absorption and transmission experiments with temperatures down to 2 K and magnetic field up to {+-}7 T.

  3. Hidden modes in open disordered media: analytical, numerical, and experimental results

    NASA Astrophysics Data System (ADS)

    Bliokh, Yury P.; Freilikher, Valentin; Shi, Z.; Genack, A. Z.; Nori, Franco

    2015-11-01

    We explore numerically, analytically, and experimentally the relationship between quasi-normal modes (QNMs) and transmission resonance (TR) peaks in the transmission spectrum of one-dimensional (1D) and quasi-1D open disordered systems. It is shown that for weak disorder there exist two types of the eigenstates: ordinary QNMs which are associated with a TR, and hidden QNMs which do not exhibit peaks in transmission or within the sample. The distinctive feature of the hidden modes is that unlike ordinary ones, their lifetimes remain constant in a wide range of the strength of disorder. In this range, the averaged ratio of the number of transmission peaks {N}{{res}} to the number of QNMs {N}{{mod}}, {N}{{res}}/{N}{{mod}}, is insensitive to the type and degree of disorder and is close to the value \\sqrt{2/5}, which we derive analytically in the weak-scattering approximation. The physical nature of the hidden modes is illustrated in simple examples with a few scatterers. The analogy between ordinary and hidden QNMs and the segregation of superradiant states and trapped modes is discussed. When the coupling to the environment is tuned by an external edge reflectors, the superradiance transition is reproduced. Hidden modes have been also found in microwave measurements in quasi-1D open disordered samples. The microwave measurements and modal analysis of transmission in the crossover to localization in quasi-1D systems give a ratio of {N}{{res}}/{N}{{mod}} close to \\sqrt{2/5}. In diffusive quasi-1D samples, however, {N}{{res}}/{N}{{mod}} falls as the effective number of transmission eigenchannels M increases. Once {N}{{mod}} is divided by M, however, the ratio {N}{{res}}/{N}{{mod}} is close to the ratio found in 1D.

  4. Optimum iodine concentration of contrast material through microcatheters: hydrodynamic analysis of experimental results.

    PubMed

    Yamauchi, Teiyu; Furui, Shigeru; Harasawa, Arimi; Ishimura, Makoto; Imai, Tatsuhiko; Hayashi, Toshimitsu

    2002-07-21

    It is important to increase the iodine delivery rate (I), that is the iodine concentration of the contrast material (C) x the flow rate of the contrast material (Q), through a catheter to obtain high quality arteriograms. The iodine delivery rate varies depending on the iodine concentration of the contrast material. The purpose of this study is to estimate the optimum iodine concentration (Copt) of contrast material (i.e. the iodine concentration at which I becomes maximum) through a microcatheter of a given length (L), inner diameter (D) and injection pressure (P). Iohexol, ioversol and iopamidol of 11-12 iodine concentrations (140-350, 160-350 or 160-370 mg cm(-3)) at 37 degrees C are used. I and Reynolds number (Re) of the flow of each contrast material through four microcatheters (0.49-0.68 mm in inner diameter, 1000-1500 mm in length) at injection pressures of 1.38, 2.76, 4.14 and 5.52 x 10(6) Pa (200, 400, 600 and 800 pounds per square inch) are obtained experimentally. The relationships between I and C and between I and Re are examined for each catheter and injection pressure. Copt is 160-280 mg cm(-3) for iohexol, 180-280 mg cm(-3) for ioversol and 200-300 mg cm(-3) for iopamidol. I becomes maximum when Re approximates the critical Reynolds number (Re approximately 2300). Utilizing this principle, we can estimate Copt and its flow rate through a microcatheter of a given L, D and P.

  5. Optimum iodine concentration of contrast material through microcatheters: hydrodynamic analysis of experimental results

    NASA Astrophysics Data System (ADS)

    Yamauchi, Teiyu; Furui, Shigeru; Harasawa, Arimi; Ishimura, Makoto; Imai, Tatsuhiko; Hayashi, Toshimitsu

    2002-07-01

    It is important to increase the iodine delivery rate (I), that is the iodine concentration of the contrast material (C) × the flow rate of the contrast material (Q), through a catheter to obtain high quality arteriograms. The iodine delivery rate varies depending on the iodine concentration of the contrast material. The purpose of this study is to estimate the optimum iodine concentration (Copt) of contrast material (i.e. the iodine concentration at which I becomes maximum) through a microcatheter of a given length (L), inner diameter (D) and injection pressure (P). Iohexol, ioversol and iopamidol of 11-12 iodine concentrations (140-350, 160-350 or 160-370 mg cm-3) at 37 °C are used. I and Reynolds number (Re) of the flow of each contrast material through four microcatheters (0.49-0.68 mm in inner diameter, 1000-1500 mm in length) at injection pressures of 1.38, 2.76, 4.14 and 5.52 × 106 Pa (200, 400, 600 and 800 pounds per square inch) are obtained experimentally. The relationships between I and C and between I and Re are examined for each catheter and injection pressure. Copt is 160-280 mg cm-3 for iohexol, 180-280 mg cm-3 for ioversol and 200-300 mg cm-3 for iopamidol. I becomes maximum when Re approximates the critical Reynolds number (Re ≃ 2300). Utilizing this principle, we can estimate Copt and its flow rate through a microcatheter of a given L, D and P.

  6. From the experimental simulation to integrated non-destructive analysis by means of optical and infrared techniques: results compared

    NASA Astrophysics Data System (ADS)

    Sfarra, S.; Ibarra-Castanedo, C.; Lambiase, F.; Paoletti, D.; Di Ilio, A.; Maldague, X.

    2012-11-01

    In this work the possibility of modeling manufacturing ceramic products is analyzed through the application of transient thermography, holographic interferometry and digital speckle photography, in order to identify the subsurface defects characteristics. This integrated method could be used to understand the nature of heterogeneous materials (such as plastic, sponge simulating a void, wood, aluminum) potentially contained within ceramic materials, as well as to predict crack formation due to them. The paper presents the analysis of green ceramic tile containing defects of different types and sizes located at different depths. The finite element method is used for solving the problem of transient heat transfer occurring in experimental conditions. Unknown parameters of the numerical model (such as convective heat transfer coefficients and sample surface emissivity) were adjusted to obtain numerical simulation results as close as possible to those obtained experimentally. Similarities and differences between experimental and simulated data are analyzed and discussed. Possibilities for improving the results and further developments are proposed.

  7. Bulk Modulus of Sc2O3: Ab initio Calculations and Experimental Results

    SciTech Connect

    S Barzilai; I Halvey; O Yeheskel

    2011-12-31

    The bulk modulus of scandia is evaluated by ab initio calculation, based on density functional theory, and compared with bulk modulus measurement on nearly fully dense scandia and with the value attained from the equation of state based on diamond anvil cell measurements. The current results are in the upper range of the bulk moduli results in the literature. The scatter in the literature results might be explained by the differences in the specific volumes of the measured and calculated cases. For the specific volume of 59.65{+-}0.07 {angstrom}{sup 3} the average measured isothermal bulk modulus of scandia from the present study and recent literature results is 188{+-}10 GPa.

  8. Investigations of a Combustor Using a 9-Point Swirl-Venturi Fuel Injector: Recent Experimental Results

    NASA Technical Reports Server (NTRS)

    Hicks, Yolanda R.; Heath, Christopher M.; Anderson, Robert C.; Tacina, Kathleen M.

    2012-01-01

    This paper explores recent results obtained during testing in an optically-accessible, JP8-fueled, flame tube combustor using baseline Lean Direct Injection (LDI) research hardware. The baseline LDI geometry has nine fuel/air mixers arranged in a 3 x 3 array. Results from this nine-element array include images of fuel and OH speciation via Planar Laser-Induced Fluorescence (PLIF), which describe fuel spray pattern and reaction zones. Preliminary combustion temperatures derived from Stokes/Anti-Stokes Spontaneous Raman Spectroscopy are also presented. Other results using chemiluminescence from major combustion radicals such as CH* and C2* serve to identify the primary reaction zone, while OH PLIF shows the extent of reaction further downstream. Air and fuel velocities and fuel drop size results are also reported.

  9. Clinical pathology results from cranes with experimental West Nile Virus infection

    USGS Publications Warehouse

    Olsen, Glenn H.

    2011-01-01

    Sandhill cranes (Grus canadensis) were vaccinated for and then challenged with West Nile virus. Resulting titers demonstrated protection in the vaccinated-challenged cranes as compared to the unvaccinated-challenged cranes. Clinical pathology results showed challenged cranes, whether vaccinated or not, had a decrease in their hematocrits and an elevation of 2.5-fold in their white blood cell counts as compared to unchallenged control sandhill cranes. No differences were apparent in the differential counts of heterophils and lymphocytes.

  10. Analysis of the Learjet 35/36 Wing and Correlation with Experimental Results

    NASA Technical Reports Server (NTRS)

    Abla, M. H.; Boroughs, R. R.; Cook, E. L.

    1976-01-01

    Two NASTRAN models of the Gates Learjet Corporation Model 35/36 Wing were developed. The models and the problems encountered in their development are discussed. A skin buckling analysis used for the ultimate loading conditions is presented. A discussion of the static tests and the correlation of the static test with the NASTRAN results and the results of a supplementary semimonocoque beam analysis are also included.

  11. How People Actually Use Thermostats

    SciTech Connect

    Meier, Alan; Aragon, Cecilia; Hurwitz, Becky; Mujumdar, Dhawal; Peffer, Therese; Perry, Daniel; Pritoni, Marco

    2010-08-15

    Residential thermostats have been a key element in controlling heating and cooling systems for over sixty years. However, today's modern programmable thermostats (PTs) are complicated and difficult for users to understand, leading to errors in operation and wasted energy. Four separate tests of usability were conducted in preparation for a larger study. These tests included personal interviews, an on-line survey, photographing actual thermostat settings, and measurements of ability to accomplish four tasks related to effective use of a PT. The interviews revealed that many occupants used the PT as an on-off switch and most demonstrated little knowledge of how to operate it. The on-line survey found that 89% of the respondents rarely or never used the PT to set a weekday or weekend program. The photographic survey (in low income homes) found that only 30% of the PTs were actually programmed. In the usability test, we found that we could quantify the difference in usability of two PTs as measured in time to accomplish tasks. Users accomplished the tasks in consistently shorter times with the touchscreen unit than with buttons. None of these studies are representative of the entire population of users but, together, they illustrate the importance of improving user interfaces in PTs.

  12. Experimental results of tests to investigate the effects of hole diameter resulting from bottom head failure on Direct Containment Heating (DCH) in the Surtsey Test Facility

    SciTech Connect

    Allen, M.D.; Pilch, M.; Griffith, R.O. ); Nichols, R.T. )

    1992-03-01

    The WC-1 and WC-3 experiments were conducted using a dry, 1:10 linear scale model of the Zion reactor cavity to obtain baseline data for comparison to future experiments that will have water in the cavity. WC-1 and WC-3 were performed with similar initial conditions except for the exit hole between the melt generator and the scaled model of the reactor cavity. For both experiments the molten core debris was simulated by a thermitically generated melt formed from 50 kg of iron oxide/aluminum/chromium powders. After the thermite was ignited in WC-1, the melt was forcibly ejected by 374 moles of slightly superheated steam at an initial driving pressure of 4.6 MPa through an exit hole with an actual diameter of 4.14 cm into the scaled model of the reactor cavity. In WC-3, the molten thermite was ejected by 300 moles of slightly superheated steam at an initial driving pressure of 3.8 MPa through an exit hole with an actual diameter of 10.1 cm into the scaled model of the reactor cavity. Because of the larger exit hole diameter, WC-3 had a shorter blowdown time than WC-1, 0.8's compared to 3.0's. WC-3 also had a higher debris velocity than WC-1, 54 m/s compared to 17.5 m/s. Posttest sieve analysis of debris recovered from the Surtsey vessel gave identical results in WC-1 and WC-3 for the sieve mass median particle diameter, i.e. 1.45 mm. The total mass ejected into the Surtsey vessel in WC-3 was 45.0 kg compared to 47.9 kg in WC-1. The peak pressure increase in Surtsey due to the high-pressure melt ejection (HPME) was 0.275 MPa in WC-3 and 0.272 in WC-1. Steam/metal reactions produced 181 moles of of hydrogen in WC-3 and 145 moles of hydrogen in WC-1.

  13. Mechanism of amorphous silica particles precipitation: simulation approach compared to experimental results

    NASA Astrophysics Data System (ADS)

    Noguera, Claudine; Fritz, Bertrand; Clement, Alain

    2015-04-01

    Despite its importance in numerous industrial and natural processes, many unsolved questions remain regarding the mechanism of silica precipitation in aqueous solutions: order of the reaction, role of silica oligomers, existence of an induction time and characteristics of the particle population. Beyond empirical approaches used in the past, we demonstrate that the classical nucleation theory associated to a size dependent growth law, as embedded in the NANOKIN code (1-3), allows a quantitative description of precipitation occurring under largely different experimental conditions : preexisting initial supersaturation in a large domain of temperature (5-150°C) and chemical composition (4), supersaturation reached by neutralization of a high pH silica solution (5) or by fast cooling (6). In that way, the mechanism of silica precipitation can be unraveled. We are able to discard the hypothesis of an induction time as an explanation for the plateaus observed in the saturation curves in these experiments. We challenge the role of oligomer incorporation at the growth stage to account for the observed rate laws and we stress the difference between the order of the growth law and the order of the total reaction rate. We also demonstrate that the characteristics of the particle population are strongly dependent on the way supersaturation is reached (7). Such a microscopic approach thus proves to be well suited to elucidate the mechanism of nanoparticle formation in natural and industrial contexts, involving silica, but also other mineral phases produced as nanoparticles (8). (1) Noguera C., Fritz B., Clément A. and Barronet A., J. Cryst. Growth, 2006, 297, 180. (2) Noguera C., Fritz B., Clément A. and Barronet A., J. Cryst. Growth, 2006, 297, 187. (3) Fritz B., Clément A., Amal Y. and Noguera C., Geochim. Cosmochim. Acta, 2009, 73, 1340. (4) Rothbaum, H.P. and Rohde A.G., J. Colloid Interf. Sci., 1979,71, 533. (5) Tobler D.J., Shaw S. and Benning L.G., Geochim

  14. An iwatsubo-based solution for labyrinth seals - comparison with experimental results

    NASA Technical Reports Server (NTRS)

    Childs, D. W.; Scharrer, J. K.

    1984-01-01

    The basic equations are derived for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equation. The first-order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to published test results.

  15. Experimental and calculational results from the Spent Fuel Test-Climax

    SciTech Connect

    Patrick, W.C.; Ramspott, L.D.; Ballou, L.B.

    1982-10-14

    The Spent Fuel Test-Climax (SFT-C) is being conducted under the technical direction of the Lawrence Livermore National Laboratory for the US Department of Energy. The SFT-C is located 420 m below surface in the Climax placed in test storage in April and May 1980. At the same time, 6 electrical elevated-temperature phase of the test. Data related to heat transfer, thermomechanical response, radiation dose, and radiation damage have been collected and are presented here, as appropriate, with calculational results. In general, measured and calculated results compare well.

  16. Experimental results supporting the determination of service quality objectives for DBS systems

    NASA Technical Reports Server (NTRS)

    Chouinard, G.; Whyte, W. A., Jr.; Goldberg, A. A.; Jones, B. L.

    1985-01-01

    A summary of the results of a joint United States and Canadian program on subjective measurements of the picture degradation caused by noise and interference on an NTSC encoded color television signal is given in this paper. The effects of system noise, cochannel and adjacent channel interference, and both single entry and aggregate as well as a combination of these types of interference were subjectively evaluated by expert and nonexpert viewers under reference conditions. These results were used to develop the rationale used at RARC '83 to establish the service quality objective for planning the DBS service for the American continents.

  17. Experimental results on QCD (Quantum Chromodynamics) from e/sup +/e/sup -/ annihilation

    SciTech Connect

    de Boer, W.

    1987-09-01

    A review is given on QCD results from studying e/sup +/e/sup -/ annihilation with the PEP and PETRA storage rings with special emphasis on jet physics and the determination of the strong coupling constant ..cap alpha../sub s/. 92 refs., 28 figs., 3 tabs.

  18. Proton-proton bremsstrahlung calculation: Comparison with recent high-precision experimental results

    SciTech Connect

    Li Yi; Liou, M.K.; Schreiber, W.M.

    2005-08-01

    Proton-proton bremsstrahlung cross sections and analyzing powers have been calculated at 190 MeV by using a one-boson-exchange model. The results are compared with the recently published high-precision Kernfysisch-Versneller-Instituut (KVI) data. Satisfactory agreement between theory and experiment has been found.

  19. Hypersonic research engine/aerothermodynamic integration model, experimental results. Volume 2: Mach 6 performance

    NASA Technical Reports Server (NTRS)

    Andrews, E. H., Jr.; Mackley, E. A.

    1976-01-01

    Computer program performance results of a Mach 6 hypersonic research engine during supersonic and subsonic combustion modes were presented. The combustion mode transition was successfully performed, exit surveys made, and effects of altitude, angle of attack, and inlet spike position were determined during these tests.

  20. Results from an Experimental Study about Reinforcements Employed in Early Training

    ERIC Educational Resources Information Center

    Aparicio, Maria Teresa Sanz

    2004-01-01

    The Down's syndrome population presents a social quotient higher than its intelligence quotient, the main characteristic of its personality and because of the pronounced hypotony suffered by them, principally in the first years of life. This report shows the results of a study carried out about differential acquisitions of two groups of trisomy-21…