NASA Astrophysics Data System (ADS)
Siroux, Monica; Harmand, Souad; Desmet, Bernard
2001-03-01
Local and mean convective heat transfer from a rotating TGV brake disc model in the actual environment and submitted to an air flow parallel to the disc surface is studied experimentally in this paper. The experimental technique is based on the use of a heated thermally thick disc combined with the technique of temperature measurement by infrared thermography. The local convective heat transfer coefficient from the disc surface is identified by solving the steady state heat equation by finite difference method using the experimental temperature distribution as boundary conditions. These tests were carried out for rotational speed (omega) between 325 and 2000 rpm (rotational Reynolds number Re between 88500 and 545000) so as to obtain laminar and turbulent flow on the disc, and for air flow velocity U ranging between 0 and 12 m s-1 (air flow Reynolds number Re0 between 0 and 153000).
NASA Astrophysics Data System (ADS)
Siroux, Monica; Harmand, Souad; Desmet, Bernard
2002-07-01
We present an experimental identification of the local and mean Nusselt number from a rotating TGV brake disk model in the actual environment and exposed to an air flow parallel to the disk surface. This method is based on the use of a heated thermally thick disk combined with the technique of temperature measurement by infrared thermography. The local and mean convective heat transfer coefficient from the disk surface is identified by solving the steady state heat equation by a finite difference method using the experimental temperature distribution as boundary conditions. The experimental setup is constituted of a model disk with all the representative parts of the actual TGV brake system. The disk and its actual environment are inside a wind tunnel test section, so that the rotational disk speed and the air flow velocity can be varied. Tests were carried out for rotational speeds w between 325 and 2000 rpm (rotational Reynolds number Re between 88,500 and 545,000), and for an air flow velocity U ranging between 0 and 12 m(DOT)s-1 (air flow Reynolds number Re0 between 0 and 153,000).
McGuire, Joseph C.
1982-01-01
A heat transfer system for a nuclear reactor. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.
Not Available
1980-03-07
A heat transfer system for a nuclear reactor is described. Heat transfer is accomplished within a sealed vapor chamber which is substantially evacuated prior to use. A heat transfer medium, which is liquid at the design operating temperatures, transfers heat from tubes interposed in the reactor primary loop to spaced tubes connected to a steam line for power generation purposes. Heat transfer is accomplished by a two-phase liquid-vapor-liquid process as used in heat pipes. Condensible gases are removed from the vapor chamber through a vertical extension in open communication with the chamber interior.
Quenching fundamentals: Heat transfer
MacKenzie, D.S.; Totten, G.E.; Webster, G.M.
1996-12-31
Quenching is essentially a heat transfer problem. It is necessary to quench parts fast enough that adequate mechanical and corrosion properties are achieved, but not so fast that detrimental distortion and residual stresses are formed. In addition, non-uniform heat transfer across the surface of a part will produce thermal gradients which will also create distortion or residual stresses. In this paper, the role of agitation will be discussed in terms of the heat transfer coefficient. A brief review of the published heat transfer literature will be discussed in terms of the fluid flow on heat transfer coefficient, with implications on quenching.
Heat transfer in energy problems
NASA Astrophysics Data System (ADS)
Mizushina, T.; Yang, W. J.
Results of recent research are presented concerning heat transfer in energy problems, including high-temperature heat transfer, high-flux heat transfer, high-performance heat transfer, heat transfer in nonconventional energy (power and propulsion) systems, and novel heat transfer techniques. Topics discussed include studies of full-coverage film cooling, radiative properties of metals and alloys at high temperature, critical heat flux conditions in high-quality boiling systems, heat transfer characteristics of the evaporation of a liquid droplet on heated surfaces, high-performance surfaces for non-boiling heat transfer, and high performance heat transfer surfaces for boiling and condensation. Also examined are high flux heat transfer in gaseous solid suspension flow, nuclear process heat applications of high temperature heat exchange, heat transfer considerations in the use of new energy resources, and high performance mist-cooled condensers for geothermal binary cycle plants. No individual items are abstracted in this volume
NASA Technical Reports Server (NTRS)
Burbach, T.
1985-01-01
The heat transfer from hot water to a cold copper pipe in laminar and turbulent flow condition is determined. The mean flow through velocity in the pipe, relative test length and initial temperature in the vessel were varied extensively during tests. Measurements confirm Nusselt's theory for large test lengths in laminar range. A new equation is derived for heat transfer for large starting lengths which agrees satisfactorily with measurements for large starting lengths. Test results are compared with the new Prandtl equation for heat transfer and correlated well. Test material for 200- and to 400-diameter test length is represented at four different vessel temperatures.
Heat transfer fluids containing nanoparticles
Singh, Dileep; Routbort, Jules; Routbort, A.J.; Yu, Wenhua; Timofeeva, Elena; Smith, David S.; France, David M.
2016-05-17
A nanofluid of a base heat transfer fluid and a plurality of ceramic nanoparticles suspended throughout the base heat transfer fluid applicable to commercial and industrial heat transfer applications. The nanofluid is stable, non-reactive and exhibits enhanced heat transfer properties relative to the base heat transfer fluid, with only minimal increases in pumping power required relative to the base heat transfer fluid. In a particular embodiment, the plurality of ceramic nanoparticles comprise silicon carbide and the base heat transfer fluid comprises water and water and ethylene glycol mixtures.
Thermal radiation heat transfer.
NASA Technical Reports Server (NTRS)
Siegel, R.; Howell, J. R.
1972-01-01
A comprehensive discussion of heat transfer by thermal radiation is presented, including the radiative behavior of materials, radiation between surfaces, and gas radiation. Among the topics considered are property prediction by electromagnetic theory, the observed properties of solid materials, radiation in the presence of other modes of energy transfer, the equations of transfer for an absorbing-emitting gas, and radiative transfer in scattering and absorbing media. Also considered are radiation exchange between black isothermal surfaces, radiation exchange in enclosures composed of diffuse gray surfaces and in enclosures having some specularly reflecting surfaces, and radiation exchange between nondiffuse nongray surfaces. The use of the Monte Carlo technique in solving radiant-exchange problems and problems of radiative transfer through absorbing-emitting media is explained.
ERIC Educational Resources Information Center
Knapp, Henry H., III
This module on heat transfer is one of six in a series intended for use as supplements to currently available materials on solar energy and energy conservation. Together with the recommended texts and references (sources are identified), these modules provide an effective introduction to energy conservation and solar energy technologies. The…
Gambill, W.R.; Greene, N.D.
1960-08-30
A method is given for increasing burn-out heat fluxes under nucleate boiling conditions in heat exchanger tubes without incurring an increase in pumping power requirements. This increase is achieved by utilizing a spinning flow having a rotational velocity sufficient to produce a centrifugal acceleration of at least 10,000 g at the tube wall. At this acceleration the heat-transfer rate at burn out is nearly twice the rate which can be achieved in a similar tube utilizing axial flow at the same pumping power. At higher accelerations the improvement over axial flow is greater, and heat fluxes in excess of 50 x 10/sup 6/ Btu/hr/sq ft can be achieved.
Methane heat transfer investigation
NASA Technical Reports Server (NTRS)
1984-01-01
Future high chamber pressure LOX/hydrocarbon booster engines require copper base alloy main combustion chamber coolant channels similar to the SSME to provide adequate cooling and reusable engine life. Therefore, it is of vital importance to evaluate the heat transfer characteristics and coking thresholds for LNG (94% methane) cooling, with a copper base alloy material adjacent to he fuel coolant. High pressure methane cooling and coking characteristics recently evaluated at Rocketdyne using stainless steel heated tubes at methane bulk temperatures and coolant wall temperatures typical of advanced engine operation except at lower heat fluxes as limited by the tube material. As expected, there was no coking observed. However, coking evaluations need be conducted with a copper base surface exposed to the methane coolant at higher heat fluxes approaching those of future high chamber pressure engines.
Methane heat transfer investigation
NASA Technical Reports Server (NTRS)
Cook, R. T.
1984-01-01
Future high chamber pressure LOX/hydrocarbon booster engines require copper-base alloy main combustion chamber coolant channels similar to the SSME to provide adequate cooling and resuable engine life. Therefore, it is of vital importance to evaluate the heat transfer characteristics and coking thresholds for LNG (94% methane) cooling, with a copper-base alloy material adjacent to the fuel coolant. High-pressure methane cooling and coking characteristics were recently evaluated using stainless-steel heated tubes at methane bulk temperatures and coolant wall temperatures typical of advanced engine operation except at lower heat fluxes as limited by the tube material. As expected, there was no coking observed. However, coking evaluations need be conducted with a copper-base surface exposed to the methane coolant at higher heat fluxes approaching those of future high chamber pressure engines.
Basmajian, V.V.
1986-01-28
This patent describes a heat transfer apparatus which consists of: heat exchanging means for orientation in the earth below ground substantially vertically, having a hollow conduit of length from top to bottom much greater than the span across the hollow conduit orthogonal to its length with a top, bottom and an intermediate portion contiguous and communicating with the top and bottom portions for allowing thermally conductive fluid to flow freely between the top, intermediate and bottom portions for immersion in thermally conductive fluid in the region around the heat exchanging means for increasing the heat flow between the latter and earth when inserted into a substantially vertical borehole in the earth with the top portion above the bottom portion. The heat exchanger consists of heat exchanging conduit means in the intermediate portion for carrying refrigerant. The heat exchanging conduit consisting of tubes of thermally conductive material for carrying the refrigerant and extending along the length of the hollow conduit for a tube length that is less than the length of the hollow conduit. The hollow conduit is formed with port means between the top and the plurality of tubes for allowing the thermally conductive fluid to pass in a flow path embracing the tubes, the bottom portion, an outer channel around the hollow conduit and the port means.
Transferring heat during a bounce
NASA Astrophysics Data System (ADS)
Shiri, Samira; Bird, James
2015-11-01
When a hot liquid drop impacts a cold non-wetting surface, the temperature difference drives heat transfer. If the drop leaves the surface before reaching thermal equilibrium, the amount of heat transfer may depend on the contact time. Past studies exploring finite-time heat exchange with droplets focus on the Leidenfrost condition where heat transfer is regulated by a thin layer of vapor. Here, we present systematic experiments to measure the heat transferred by a bouncing droplet in non-Leidenfrost conditions. We propose a physical model of this heat transfer and compare our model to the experiments.
Heat-Transfer Coupling For Heat Pipes
NASA Technical Reports Server (NTRS)
Nesmith, Bill J.
1991-01-01
Proposed welded heat-transfer coupling joins set of heat pipes to thermoelectric converter. Design avoids difficult brazing operation. Includes pair of mating flanged cups. Upper cup integral part of housing of thermoelectric converter, while lower cup integral part of plate supporting filled heat pipes. Heat pipes prefilled. Heat of welding applied around periphery of coupling, far enough from heat pipes so it would not degrade working fluid or create excessive vapor pressure in the pipes.
Heat transfer in aeropropulsion systems
NASA Astrophysics Data System (ADS)
Simoneau, R. J.
1985-07-01
Aeropropulsion heat transfer is reviewed. A research methodology based on a growing synergism between computations and experiments is examined. The aeropropulsion heat transfer arena is identified as high Reynolds number forced convection in a highly disturbed environment subject to strong gradients, body forces, abrupt geometry changes and high three dimensionality - all in an unsteady flow field. Numerous examples based on heat transfer to the aircraft gas turbine blade are presented to illustrate the types of heat transfer problems which are generic to aeropropulsion systems. The research focus of the near future in aeropropulsion heat transfer is projected.
Heat transfer in aeropropulsion systems
NASA Technical Reports Server (NTRS)
Simoneau, R. J.
1985-01-01
Aeropropulsion heat transfer is reviewed. A research methodology based on a growing synergism between computations and experiments is examined. The aeropropulsion heat transfer arena is identified as high Reynolds number forced convection in a highly disturbed environment subject to strong gradients, body forces, abrupt geometry changes and high three dimensionality - all in an unsteady flow field. Numerous examples based on heat transfer to the aircraft gas turbine blade are presented to illustrate the types of heat transfer problems which are generic to aeropropulsion systems. The research focus of the near future in aeropropulsion heat transfer is projected.
Frank, Jeffrey I.; Rosengart, Axel J.; Kasza, Ken; Yu, Wenhua; Chien, Tai-Hsin; Franklin, Jeff
2006-10-10
Apparatuses, systems, methods, and computer code for, among other things, monitoring the health of samples such as the brain while providing local cooling or heating. A representative device is a heat transfer probe, which includes an inner channel, a tip, a concentric outer channel, a first temperature sensor, and a second temperature sensor. The inner channel is configured to transport working fluid from an inner inlet to an inner outlet. The tip is configured to receive at least a portion of the working fluid from the inner outlet. The concentric outer channel is configured to transport the working fluid from the inner outlet to an outer outlet. The first temperature sensor is coupled to the tip, and the second temperature sensor spaced apart from the first temperature sensor.
Conduction heat transfer solutions
VanSant, J.H.
1983-08-01
This text is a collection of solutions to a variety of heat conduction problems found in numerous publications, such as textbooks, handbooks, journals, reports, etc. Its purpose is to assemble these solutions into one source that can facilitate the search for a particular problem solution. Generally, it is intended to be a handbook on the subject of heat conduction. There are twelve sections of solutions which correspond with the class of problems found in each. Geometry, state, boundary conditions, and other categories are used to classify the problems. Each problem is concisely described by geometry and condition statements, and many times a descriptive sketch is also included. The introduction presents a synopsis on the theory, differential equations, and boundary conditions for conduction heat transfer. Some discussion is given on the use and interpretation of solutions. Supplementary data such as mathematical functions, convection correlations, and thermal properties are included for aiding the user in computing numerical values from the solutions. 155 figs., 92 refs., 9 tabs.
Conduction heat transfer solutions
VanSant, J.H.
1980-03-01
This text is a collection of solutions to a variety of heat conduction problems found in numerous publications, such as textbooks, handbooks, journals, reports, etc. Its purpose is to assemble these solutions into one source that can facilitate the search for a particular problem solution. Generally, it is intended to be a handbook on the subject of heat conduction. This material is useful for engineers, scientists, technologists, and designers of all disciplines, particularly those who design thermal systems or estimate temperatures and heat transfer rates in structures. More than 500 problem solutions and relevant data are tabulated for easy retrieval. There are twelve sections of solutions which correspond with the class of problems found in each. Geometry, state, boundary conditions, and other categories are used to classify the problems. A case number is assigned to each problem for cross-referencing, and also for future reference. Each problem is concisely described by geometry and condition statements, and many times a descriptive sketch is also included. At least one source reference is given so that the user can review the methods used to derive the solutions. Problem solutions are given in the form of equations, graphs, and tables of data, all of which are also identified by problem case numbers and source references.
NASA Astrophysics Data System (ADS)
Kanzaka, Mitsuo; Iwabuchi, Makio
1992-11-01
Heat transfer characteristics in heated tubes under periodically reversing flow conditions have been experimentally investigated, using a test apparatus that simulates heat exchangers for an actual Stirling engine. It is shown that the heat transfer characteristics under these conditions are greatly affected by the piston phase difference that generates the reversing flow of working fluid, and this phenomenon is peculiar to heat transfer under periodically reversing flow. The experimental correlation for the heat transfer coefficient under these conditions is obtained through the use of the working gas velocity evaluated from the Schmidt cycle model, which is one of the ideal Stirling cycles concerning the influence of the piston phase difference.
Tubing for augmented heat transfer
Yampolsky, J.S.; Pavlics, P.
1983-08-01
The objectives of the program reported were: to determine the heat transfer and friction characteristics on the outside of spiral fluted tubing in single phase flow of water, and to assess the relative cost of a heat exchanger constructed with spiral fluted tubing with one using conventional smooth tubing. An application is examined where an isolation water/water heat exchanger was used to transfer the heat from a gaseous diffusion plant to an external system for energy recovery. (LEW)
Catalytic combustion of actual low and medium heating value gases
NASA Technical Reports Server (NTRS)
Bulzan, D. L.
1982-01-01
Catalytic combustion of both low and medium heating value gases using actual coal derived gases obtained from operating gasifiers was demonstrated. A fixed bed gasifier with a complete product gas cleanup system was operated in an air blown mode to produce low heating value gas. A fluidized bed gasifier with a water quench product gas cleanup system was operated in both an air enriched and an oxygen blown mode to produce low and medium, heating value gas. Noble metal catalytic reactors were evaluated in 12 cm flow diameter test rigs on both low and medium heating value gases. Combustion efficiencies greater than 99.5% were obtained with all coal derived gaseous fuels. The NOx emissions ranged from 0.2 to 4 g NO2 kg fuel.
Fraas, A.P.; Wislicenus, G.F.
1961-07-11
A heat exchanger is adapted to unifomly cool a spherical surface. Equations for the design of a spherical heat exchanger hav~g tubes with a uniform center-to-center spining are given. The heat exchanger is illustrated in connection with a liquid-fueled reactor.
Is transferring an educational innovation actually a process of transformation?
Varpio, Lara; Bell, Robert; Hollingworth, Gary; Jalali, Alireza; Haidet, Paul; Levine, Ruth; Regehr, Glenn
2012-08-01
Recent debates question the extent to which adopting an educational innovation requires compromise between the innovation's original design and the adoption site's context. Through compromises, the innovation's fundamental principles may be transferred, transformed, or abandoned. This paper analyzes such compromises during the piloting of Team-Based Learning (TBL). We ask: When is the process of transferring an innovation actually a process of transformation? This study is an autoethnography of our research team's implementation process. Autoethnographies are personalized accounts where authors draw on their own experiences to extend understanding of a particular topic. To conduct this autoethnography, we used an in-depth, interactive interview with the piloting clinician educator. In the analysis of TBL's fundamental principles, some aspects of the principles transferred easily, while others were transformed. Analysis raised concerns that the transformations threatened the foundational principles of TBL. While an educational innovation's techniques may seem to be surface structures, they are realizations of deeper fundamental principles. The fundamental principles are themselves realizations of the innovation's foundational philosophy. When techniques and/or principles are modified to a context, it is important to analyze if the modifications continue to uphold the innovation's philosophy. PMID:21725841
NASA Astrophysics Data System (ADS)
Duan, Zhipeng; He, Boshu; Duan, Yuanyuan
2015-07-01
Modelling fluid flows past a body is a general problem in science and engineering. Historical sphere drag and heat transfer data are critically examined. The appropriate drag coefficient is proposed to replace the inertia type definition proposed by Newton. It is found that the appropriate drag coefficient is a desirable dimensionless parameter to describe fluid flow physical behavior so that fluid flow problems can be solved in the simple and intuitive manner. The appropriate drag coefficient is presented graphically, and appears more general and reasonable to reflect the fluid flow physical behavior than the traditional century old drag coefficient diagram. Here we present drag and heat transfer experimental results which indicate that there exists a relationship in nature between the sphere drag and heat transfer. The role played by the heat flux has similar nature as the drag. The appropriate drag coefficient can be related to the Nusselt number. This finding opens new possibilities in predicting heat transfer characteristics by drag data. As heat transfer for flow over a body is inherently complex, the proposed simple means may provide an insight into the mechanism of heat transfer for flow past a body.
Duan, Zhipeng; He, Boshu; Duan, Yuanyuan
2015-01-01
Modelling fluid flows past a body is a general problem in science and engineering. Historical sphere drag and heat transfer data are critically examined. The appropriate drag coefficient is proposed to replace the inertia type definition proposed by Newton. It is found that the appropriate drag coefficient is a desirable dimensionless parameter to describe fluid flow physical behavior so that fluid flow problems can be solved in the simple and intuitive manner. The appropriate drag coefficient is presented graphically, and appears more general and reasonable to reflect the fluid flow physical behavior than the traditional century old drag coefficient diagram. Here we present drag and heat transfer experimental results which indicate that there exists a relationship in nature between the sphere drag and heat transfer. The role played by the heat flux has similar nature as the drag. The appropriate drag coefficient can be related to the Nusselt number. This finding opens new possibilities in predicting heat transfer characteristics by drag data. As heat transfer for flow over a body is inherently complex, the proposed simple means may provide an insight into the mechanism of heat transfer for flow past a body. PMID:26189698
Heat transfer measurements for Stirling machine cylinders
NASA Technical Reports Server (NTRS)
Kornhauser, Alan A.; Kafka, B. C.; Finkbeiner, D. L.; Cantelmi, F. C.
1994-01-01
The primary purpose of this study was to measure the effects of inflow-produced heat turbulence on heat transfer in Stirling machine cylinders. A secondary purpose was to provide new experimental information on heat transfer in gas springs without inflow. The apparatus for the experiment consisted of a varying-volume piston-cylinder space connected to a fixed volume space by an orifice. The orifice size could be varied to adjust the level of inflow-produced turbulence, or the orifice plate could be removed completely so as to merge the two spaces into a single gas spring space. Speed, cycle mean pressure, overall volume ratio, and varying volume space clearance ratio could also be adjusted. Volume, pressure in both spaces, and local heat flux at two locations were measured. The pressure and volume measurements were used to calculate area averaged heat flux, heat transfer hysteresis loss, and other heat transfer-related effects. Experiments in the one space arrangement extended the range of previous gas spring tests to lower volume ratio and higher nondimensional speed. The tests corroborated previous results and showed that analytic models for heat transfer and loss based on volume ratio approaching 1 were valid for volume ratios ranging from 1 to 2, a range covering most gas springs in Stirling machines. Data from experiments in the two space arrangement were first analyzed based on lumping the two spaces together and examining total loss and averaged heat transfer as a function of overall nondimensional parameter. Heat transfer and loss were found to be significantly increased by inflow-produced turbulence. These increases could be modeled by appropriate adjustment of empirical coefficients in an existing semi-analytic model. An attempt was made to use an inverse, parameter optimization procedure to find the heat transfer in each of the two spaces. This procedure was successful in retrieving this information from simulated pressure-volume data with artificially
NASA Technical Reports Server (NTRS)
Widener, Edward L.
1992-01-01
The objective is to introduce some concepts of thermodynamics in existing heat-treating experiments using available items. The specific objectives are to define the thermal properties of materials and to visualize expansivity, conductivity, heat capacity, and the melting point of common metals. The experimental procedures are described.
NASA Technical Reports Server (NTRS)
Friedell, M. V.; Anderson, A. J.
1974-01-01
Thermal switch maintains temperature of planetary lander, within definite range, by transferring heat. Switch produces relatively large stroke and force, uses minimum electrical power, is lightweight, is vapor pressure actuated, and withstands sterilization temperatures without damage.
Heat transfer, diffusion, and evaporation
NASA Technical Reports Server (NTRS)
Nusselt, Wilhelm
1954-01-01
Although it has long been known that the differential equations of the heat-transfer and diffusion processes are identical, application to technical problems has only recently been made. In 1916 it was shown that the speed of oxidation of the carbon in iron ore depends upon the speed with which the oxygen of the combustion air diffuses through the core of gas surrounding the carbon surface. The identity previously referred to was then used to calculate the amount of oxygen diffusing to the carbon surface on the basis of the heat transfer between the gas stream and the carbon surface. Then in 1921, H. Thoma reversed that procedure; he used diffusion experiments to determine heat-transfer coefficients. Recently Lohrisch has extended this work by experiment. A technically very important application of the identity of heat transfer and diffusion is that of the cooling tower, since in this case both processes occur simultaneously.
Heat exchanger with heat transfer control
Wiard, M.R.
1986-11-18
This patent describes a multi-sided plate and fin type heat exchanger core in which plate elements, intermediately positioning spacer elements and fin strips are stacked in a layered assembly providing fluid passages for different fluids to flow in a segregated heat transfer relation to one another. The core is characterized in that at certain locations in a stacked assembly layers include spacer elements substantially closing all sides of the heat exchangers to define between adjacent fluid passages layers of increased heat transfer resistance. The fin strips are sheet-like elements corrugated to forms specifically identifiable in terms of fins per inch, there being fin strips in at least certain resistance layers differing in terms of fins per inch from other strips in certain resistance layers.
Microscale surface modifications for heat transfer enhancement.
Bostanci, Huseyin; Singh, Virendra; Kizito, John P; Rini, Daniel P; Seal, Sudipta; Chow, Louis C
2013-10-01
In this experimental study, two surface modification techniques were investigated for their effect on heat transfer enhancement. One of the methods employed the particle (grit) blasting to create microscale indentations, while the other used plasma spray coating to create microscale protrusions on Al 6061 (aluminum alloy 6061) samples. The test surfaces were characterized using scanning electron microscopy (SEM) and confocal scanning laser microscopy. Because of the surface modifications, the actual surface area was increased up to 2.8× compared to the projected base area, and the arithmetic mean roughness value (Ra) was determined to vary from 0.3 μm for the reference smooth surface to 19.5 μm for the modified surfaces. Selected samples with modified surfaces along with the reference smooth surface were then evaluated for their heat transfer performance in spray cooling tests. The cooling system had vapor-atomizing nozzles and used anhydrous ammonia as the coolant in order to achieve heat fluxes up to 500 W/cm(2) representing a thermal management setting for high power systems. Experimental results showed that the microscale surface modifications enhanced heat transfer coefficients up to 76% at 500 W/cm(2) compared to the smooth surface and demonstrated the benefits of these practical surface modification techniques to enhance two-phase heat transfer process. PMID:24003985
Heat transfer from oriented heat exchange areas
NASA Astrophysics Data System (ADS)
Vantuch, Martin; Huzvar, Jozef; Kapjor, Andrej
2014-03-01
This paper deals with the transfer of heat-driven heat transfer surface area in relation to the construction of the criterion equation for "n" horizontal pipe one about another. On the bases of theoretical models have been developed for calculating the thermal performance of natural convection by Churilla and Morgan, for various pipe diameters and temperatures. These models were compared with models created in CFD-Fluent Ansys the same boundary conditions. The aim of the analyse of heat and fluxional pipe fields "n" pipes one about another at natural convection is the creation of criterion equation on the basis of which the heat output of heat transfer from pipe oriented areas one above another with given spacing could be quantified. At presence a sum of criterion equations exists for simple geometrical shapes of individual oriented geometrical areas but the criterion equation which would consider interaction of fluxional field generated by free convection from multiple oriented areas is not mentioned in standardly accessible technical literature and other magazine publications.
Ethyl alcohol boiling heat transfer on multilayer meshed surfaces
NASA Astrophysics Data System (ADS)
Dåbek, Lidia; Kapjor, Andrej; Orman, Łukasz J.
2016-06-01
The paper presents the problem of heat transfer enhancement with the application of multilayer metal mesh structures during boiling of ethyl alcohol at ambient pressure. The preparation of samples involved sintering fine copper meshes with the copper base in the reduction atmosphere in order to prevent oxidation of the samples. The experiments included testing up to 4 layers of copper meshes. Significant augmentation of boiling heat transfer is possible, however, considerable number of meshes actually hinders heat transfer conditions and leads to the reduction in the heat flux transferred from the heater surface.
Nanofluid impingement jet heat transfer.
Zeitoun, Obida; Ali, Mohamed
2012-01-01
Experimental investigation to study the heat transfer between a vertical round alumina-water nanofluid jet and a horizontal circular round surface is carried out. Different jet flow rates, jet nozzle diameters, various circular disk diameters and three nanoparticles concentrations (0, 6.6 and 10%, respectively) are used. The experimental results indicate that using nanofluid as a heat transfer carrier can enhance the heat transfer process. For the same Reynolds number, the experimental data show an increase in the Nusselt numbers as the nanoparticle concentration increases. Size of heating disk diameters shows reverse effect on heat transfer. It is also found that presenting the data in terms of Reynolds number at impingement jet diameter can take into account on both effects of jet heights and nozzle diameter. Presenting the data in terms of Peclet numbers, at fixed impingement nozzle diameter, makes the data less sensitive to the percentage change of the nanoparticle concentrations. Finally, general heat transfer correlation is obtained verses Peclet numbers using nanoparticle concentrations and the nozzle diameter ratio as parameters. PMID:22340669
Nanofluid impingement jet heat transfer
2012-01-01
Experimental investigation to study the heat transfer between a vertical round alumina-water nanofluid jet and a horizontal circular round surface is carried out. Different jet flow rates, jet nozzle diameters, various circular disk diameters and three nanoparticles concentrations (0, 6.6 and 10%, respectively) are used. The experimental results indicate that using nanofluid as a heat transfer carrier can enhance the heat transfer process. For the same Reynolds number, the experimental data show an increase in the Nusselt numbers as the nanoparticle concentration increases. Size of heating disk diameters shows reverse effect on heat transfer. It is also found that presenting the data in terms of Reynolds number at impingement jet diameter can take into account on both effects of jet heights and nozzle diameter. Presenting the data in terms of Peclet numbers, at fixed impingement nozzle diameter, makes the data less sensitive to the percentage change of the nanoparticle concentrations. Finally, general heat transfer correlation is obtained verses Peclet numbers using nanoparticle concentrations and the nozzle diameter ratio as parameters. PMID:22340669
NASA Astrophysics Data System (ADS)
Chapman, K. S.; Ramadhyani, S.; Ramamurthy, H.; Viskanta, R.
1990-04-01
One and two-dimensional mathematical models have been developed to predict the steady state thermal performance and combustion characteristics of a natural gas-fired straight-through radiant tube. The effects of burner geometry, equivalence ratio, and preheat temperature and fuel firing rate on fuel burn-up have been investigated. The one-dimensional models for straight-through and single-ended recuperative radiant tubes have been validated using available experimental data. Thermal system models have been developed for the continuous and batch indirectly fired (radiant tube) furnaces to identify opportunities for fuel savings and enhanced productivity. Extensive parametric investigations were performed to examine the effects of load and refractory emissivities, load throughput rate and thickness on the thermal performance of the furnaces. Batch and continuous direct-fired furnace thermal system models were developed to analyze the effect of various design and operation parameters on the furnace thermal performance. An attempt was made to validate the batch furnace model by using experimental data from a small experimental furnace. Due to the size of the furnace, the two-dimensional heat conduction effects near the corners and edges of the furnace walls were significant. Since the effects were neglected in the system model, which is intended to simulate a large industrial furnace, the validation was unsuccessful. The parametric study consisted of examining the effect of the load and refractory emissivities and other operating and load parameters on the thermal performance of the batch and continuous furnaces.
NASA Astrophysics Data System (ADS)
Kanzaka, Mitsuo; Iwabuchi, Makio
1992-11-01
The heat transfer performance of the actual heat exchangers obtained from the experimental results of the test Stirling engine is presented. The heater for the test engine has 120 heat transfer tubes that consist of a bare-tube part and a fin-tube part. These tubes are located around the combustion chamber and heated by the combustion gas. The cooler is the shell-and-tube-type heat exchanger and is chilled by water. It is shown that the experimental results of heat transfer performance of the heater and cooler of the test Stirling engine are in good agreement with the results calculated by the correlation proposed in our previous heat transfer study under the periodically reversing flow condition. Our correlation is thus confirmed to be applicable to the evaluation of the heat transfer coefficient and the thermal design of the heat exchangers in the Stirling engine.
Sodium heat transfer system modeling
NASA Astrophysics Data System (ADS)
Baker, A. F.; Fewell, M. E.
1983-11-01
The sodium heat transfer system of the international energy agency (IEA) small solar power systems (SSPS) central receiver system (CRS), which includes the heliostat field, receiver, hot and cold storage vessels, and sodium/water steam generator was modeled. The computer code SOLTES (simulator of large thermal energy systems), was used to model this system. The results from SOLTES are compared to measured data.
Host turbine heat transfer overview
NASA Technical Reports Server (NTRS)
Rohde, J. E.
1984-01-01
Improved methods of predicting airfoil local metal temperatures require advances in the understanding of the physics and methods of analytically predicting the following four aerothermal loads: hot gas flow over airfoils, heat transfer rates on the gas-side of airfoils, cooling air flow inside airfoils, and heat transfer rates on the coolant-side of airfoils. A systematic building block research approach is being pursued to investigate these four areas of concern from both the experimental and analytical sides. Experimental approaches being pursued start with fundamental experiments using simple shapes and flat plates in wind tunnels, progress to more realistic cold and hot cascade tests using airfoils, continue to progress in large low-speed rigs and turbines and warm turbines, and finally, combine all the interactive effects in tests using real engines or real engine type turbine rigs. Analytical approaches being pursued also build from relatively simple steady two dimensional inviscid flow and boundary layer heat transfer codes to more advanced steady two and three dimensional viscous flow and heat transfer codes. These advanced codes provide more physics to model better the interactive effects and the true real-engine environment.
Enhancement of heat transfer in waste-heat heat exchangers
NASA Astrophysics Data System (ADS)
Stoeffler, R. C.
1980-07-01
The Fluidfire shallow fluidized bed heat transfer facility was modified to give increased air flow capacity and to allow testing with different distributor plates and with two stage heat exchangers. The effect of reduced distributor plate pressure loss and amount and type of bed material on the heat transfer performance of a single stage fluidized bed heat exchanger is explored. Elutriation from the bed was measured for different bed materials and distributor plates; alternate heat exchanger surfaces having different fin spacings were also tested. Two types of two stage fluidized bed heat exchangers were tested: one having a baffle (having almost no pressure loss) located between the stages and which allowed bed material to recirculate between upper and lower beds; the second having two distributor plates in series with no recirculation of the bed material.
Experimental research on heat transfer of pulsating heat pipe
NASA Astrophysics Data System (ADS)
Li, Jia; Yan, Li
2008-06-01
Experimental research was conducted to understand heat transfer characteristic of pulsating heat pipe in this paper, and the PHP is made of high quality glass capillary tube. Under different fill ratio, heat transfer rate and many other influence factors, the flow patterns were observed in the start-up, transition and stable stage. The effects of heating position on heat transfer were discussed. The experimental results indicate that no annular flow appears in top heating condition. Under different fill ratios and heat transfer rate, the flow pattern in PHP is transferred from bulk flow to semi-annular flow and annular flow, and the performance of heat transfer is improved for down heating case. The experimental results indicate that the total heat resistant of PHP is increased with fill ratio, and heat transfer rate achieves optimum at filling rate 50%. But for pulsating heat pipe with changing diameters the thermal resistance is higher than that with uniform diameters.
Heat transfer in aerospace propulsion
NASA Technical Reports Server (NTRS)
Simoneau, Robert J.; Hendricks, Robert C.; Gladden, Herbert J.
1988-01-01
Presented is an overview of heat transfer related research in support of aerospace propulsion, particularly as seen from the perspective of the NASA Lewis Research Center. Aerospace propulsion is defined to cover the full spectrum from conventional aircraft power plants through the Aerospace Plane to space propulsion. The conventional subsonic/supersonic aircraft arena, whether commercial or military, relies on the turbine engine. A key characteristic of turbine engines is that they involve fundamentally unsteady flows which must be properly treated. Space propulsion is characterized by very demanding performance requirements which frequently push systems to their limits and demand tailored designs. The hypersonic flight propulsion systems are subject to severe heat loads and the engine and airframe are truly one entity. The impact of the special demands of each of these aerospace propulsion systems on heat transfer is explored.
Heat transfer and planetary evolution
NASA Astrophysics Data System (ADS)
Tozer, D. C.
1985-06-01
The object of this account is to show how much one can interprete and predict about the present state of material forming planet size objects, despite the fact we do not and could never have the kind of exact or prior knowledge of initial conditions and in situ material behaviour that would make a formal mathematical analysis of the dynamical problems of planetary evolution an efficient or meaningful exercise The interest and usefulness of results obtained within these limitations stem from the highly non linear nature of planetary scale heat transfer problems when posed in any physically plausible form. The non linearity arising from a strongly temperature dependent rheology assumed for in situ planetary material is particularly valuable in deriving results insensitive to such uncertainties. Qualitatively, the thermal evolution of a planet is quite unlike that given by heat conduction calculation below a very superficial layer, and much unnecessary argument and confusion results from a persistent failure to recognise that fact. At depths that are no greater on average than a few tens of kilometres in the case of Earth, the temperature distribution is determined by a convective flow regime inaccessble to the laboratory experimenter and to the numerical methods regularly employed to study convective movement. A central and guiding quantitative result is the creation in homogeneous planet size objects having surface temperatures less than about half the absolute melting temperature of their material, of internal states with horizontally a veraged viscosity values ˜1021 poise. This happens in times short compared with the present Solar System age. The significance of this result for an understanding of such processes and features as isostasy, continental drift, a minimum in seismic S wave velocity in Earth's upper mantle, a uniformity of mantle viscosity values, the survival of liquid planetary cores and the differentiation of terrestrial planet material is examined
Heat transfer reviews 1976-1986
NASA Astrophysics Data System (ADS)
Eckert, Ernst Rudolf Georg; Goldstein, R. J.; Irvine, T. F., Jr.; Hartnett, J. P.
Theoretical and experimental investigations of heat-transfer phenomena are surveyed in a collection of annual review essays. The reviews were originally published in the International Journal of Heat and Mass Transfer. Cumulative author and subject indices are provided.
Deterioration in heat transfer of endothermal hydrocarbon fuel
NASA Astrophysics Data System (ADS)
Zhou, Weixing; Bao, Wen; Qin, Jiang; Qu, Yunfeng
2011-06-01
Numerical studies under supercritical pressure are carried out to study the heat transfer characteristics in a single-root coolant channel of the active regenerative cooling system of the scramjet engine, using actual physical properties of pentane. The relationships between wall temperature and inlet temperature, mass flow rate, wall heat flux, inlet pressure, as well as center stream temperature are obtained. The results suggest that the heat transfer deterioration occurs when the fuel temperature approaches the pseudo-critical temperature, and the wall temperature increases rapidly and heat transfer coefficient decreases sharply. The decrease of wall heat flux, as well as the increase of mass flow rate and inlet pressure makes the starting point of the heat transfer deterioration and the peak point of the wall temperature move backward. The wall temperature increment induced by heat transfer deterioration decreases, which could reduce the severity of the heat transfer deterioration. The relational expression of the heat transfer deterioration critical heat flux derives from the relationship of the mass flow rate and the inlet pressure.
Boiling Heat Transfer to Halogenated Hydrocarbon Refrigerants
NASA Astrophysics Data System (ADS)
Yoshida, Suguru; Fujita, Yasunobu
The current state of knowledge on heat transfer to boiling refrigerants (halogenated hydrocarbons) in a pool and flowing inside a horizontal tube is reviewed with an emphasis on information relevant to the design of refrigerant evaporators, and some recommendations are made for future research. The review covers two-phase flow pattern, heat transfer characteristics, correlation of heat transfer coefficient, influence of oil, heat transfer augmentation, boiling from tube-bundle, influence of return bend, burnout heat flux, film boiling, dryout and post-dryout heat transfer.
Is Transferring an Educational Innovation Actually a Process of Transformation?
ERIC Educational Resources Information Center
Varpio, Lara; Bell, Robert; Hollingworth, Gary; Jalali, Alireza; Haidet, Paul; Levine, Ruth; Regehr, Glenn
2012-01-01
Recent debates question the extent to which adopting an educational innovation requires compromise between the innovation's original design and the adoption site's context. Through compromises, the innovation's fundamental principles may be transferred, transformed, or abandoned. This paper analyzes such compromises during the piloting of…
Heat exchanger device and method for heat removal or transfer
Koplow, Jeffrey P.
2012-07-24
Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.
Heat exchanger device and method for heat removal or transfer
Koplow, Jeffrey P
2015-03-24
Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.
Heat exchanger device and method for heat removal or transfer
Koplow, Jeffrey P
2013-12-10
Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.
Heat exchanger device and method for heat removal or transfer
Koplow, Jeffrey P.
2015-12-08
Systems and methods for a forced-convection heat exchanger are provided. In one embodiment, heat is transferred to or from a thermal load in thermal contact with a heat conducting structure, across a narrow air gap, to a rotating heat transfer structure immersed in a surrounding medium such as air.
Heat Transfer in a Thermoacoustic Process
ERIC Educational Resources Information Center
Beke, Tamas
2012-01-01
Thermoacoustic instability is defined as the excitation of acoustic modes in chambers with heat sources due to the coupling between acoustic perturbations and unsteady heat addition. The major objective of this paper is to achieve accurate theoretical results in a thermoacoustic heat transfer process. We carry out a detailed heat transfer analysis…
Heat transfer and flow characteristics on a gas turbine shroud.
Obata, M; Kumada, M; Ijichi, N
2001-05-01
The work described in this paper is an experimental investigation of the heat transfer from the main flow to a turbine shroud surface, which may be applicable to ceramic gas turbines. Three kinds of turbine shrouds are considered with a flat surface, a taper surface and a spiral groove surface opposite to the blades in an axial flow turbine of actual turbo-charger. Heat transfer measurements were performed for the experimental conditions of a uniform heat flux or a uniform wall temperature. The effects of the inlet flow angle, rotational speed, and tip clearance on the heat transfer coefficient were clarified under on- and off-design flow conditions. The mean heat transfer coefficient was correlated to the blade Reynolds number and tip clearance, and compared with an experimental correlation and measurements of a flat surface. A comparison was also made for the measurement of static pressure distributions. PMID:11460639
Liquid metal heat transfer issues
Hoffman, H.W.; Yoder, G.L.
1984-01-01
An alkali liquid metal cooled nuclear reactor coupled with an alkali metal Rankine cycle provides a practicable option for space systems/missions requiring power in the 1 to 100 MW(e) range. Thermal issues relative to the use of alkali liquid metals for this purpose are identified as these result from the nature of the alkali metal fluid itself, from uncertainties in the available heat transfer correlations, and from design and performance requirements for system components operating in the earth orbital microgravity environment. It is noted that, while these issues require further attention to achieve optimum system performance, none are of such magnitude as to invalidate this particular space power concept.
Heat Transfer in Complex Fluids
Mehrdad Massoudi
2012-01-01
(linear) behavior for a given range of parameters or geometries; there are many empirical or semi-empirical constitutive equations suggested for these fluids. There have also been many non-linear constitutive relations which have been derived based on the techniques of continuum mechanics. The non-linearities oftentimes appear due to higher gradient terms or time derivatives. When thermal and or chemical effects are also important, the (coupled) momentum and energy equations can give rise to a variety of interesting problems, such as instability, for example the phenomenon of double-diffusive convection in a fluid layer. In Conclusion, we have studied the flow of a compressible (density gradient type) non-linear fluid down an inclined plane, subject to radiation boundary condition. The heat transfer is also considered where a source term, similar to the Arrhenius type reaction, is included. The non-dimensional forms of the equations are solved numerically and the competing effects of conduction, dissipation, heat generation and radiation are discussed. It is observed that the velocity increases rapidly in the region near the inclined surface and is slower in the region near the free surface. Since R{sub 7} is a measure of the heat generation due to chemical reaction, when the reaction is frozen (R{sub 7}=0.0) the temperature distributions would depend only on R{sub 1}, and R{sub 2}, representing the effects of the pressure force developed in the material due to the distribution, R{sub 3} and R{sub 4} viscous dissipation, R{sub 5} the normal stress coefficient, R{sub 6} the measure of the emissivity of the particles to the thermal conductivity, etc. When the flow is not frozen (RP{sub 7} > 0) the temperature inside the flow domain is much higher than those at the inclined and free surfaces. As a result, heat is transferred away from the flow toward both the inclined surface and the free surface with a rate that increases as R{sub 7} increases. For a given temperature, an
Heat transfer in serpentine flow passages with rotation
NASA Astrophysics Data System (ADS)
Mochizuki, S.; Takamura, J.; Yamawaki, S.; Yang, Wen-Jei
1992-06-01
Results are reported of an experimental study tracing heat transfer performance in a rotating serpentine flow passage of a square cross section. The test section is preceded by a hydrodynamic calming region. The test model is a blow-up (by seven times) of actual winding flow passages in rotor blades. It is concluded that the flow in the 180-deg bends exhibits strong 3D structure. The heat transfer coefficient in the bend is substantially higher than in the straight flow passages. The average heat transfer characteristics over the entire flow passage is greatly affected by flow at the 180-deg bends. Due to secondary flow induced by the Coriolis force, the heat transfer coefficient in the radially outward flow passages diminish on the leading surface, but increase on the trailing surface, with an increase in rotational speed. The trend is reversed in the radially inward flow passages.
NASA Technical Reports Server (NTRS)
Garg, Vijay K.
2001-01-01
The turbine gas path is a very complex flow field. This is due to a variety of flow and heat transfer phenomena encountered in turbine passages. This manuscript provides an overview of the current work in this field at the NASA Glenn Research Center. Also, based on the author's preference, more emphasis is on the computational work. There is much more experimental work in progress at GRC than that reported here. While much has been achieved, more needs to be done in terms of validating the predictions against experimental data. More experimental data, especially on film cooled and rough turbine blades, are required for code validation. Also, the combined film cooling and internal cooling flow computation for a real blade is yet to be performed. While most computational work to date has assumed steady state conditions, the flow is clearly unsteady due to the presence of wakes. All this points to a long road ahead. However, we are well on course.
Twin reservoir heat transfer circuit
Urch, J.F.
1986-09-23
This patent describes a heat transfer means comprising circuitry defining a closed flow path for working fluid; a primary circuit forming part of the path and having two ends at one of which the working fluid is at a high pressure and at the other of which the working fluid is at a low pressure. The circuitry defines a fluid supply reservoir and a fluid collection reservoir disposed respectively at the two ends; ejector means in the primary circuit; a drive fluid inlet, and exhaust outlet and a suction inlet provided on the ejector means. Also included are a branch circuit bridging a section of the primary circuit and an outlet end of the branch circuit connected to the suction inlet of the ejector means.
Radiative heat transfer in porous uranium dioxide
Hayes, S.L.
1992-12-01
Due to low thermal conductivity and high emissivity of UO{sub 2}, it has been suggested that radiative heat transfer may play a significant role in heat transfer through pores of UO{sub 2} fuel. This possibility was computationally investigated and contribution of radiative heat transfer within pores to overall heat transport in porous UO{sub 2} quantified. A repeating unit cell was developed to model approximately a porous UO{sub 2} fuel system, and the heat transfer through unit cells representing a wide variety of fuel conditions was calculated using a finite element computer program. Conduction through solid fuel matrix as wekk as pore gas, and radiative exchange at pore surface was incorporated. A variety of pore compositions were investigated: porosity, pore size, shape and orientation, temperature, and temperature gradient. Calculations were made in which pore surface radiation was both modeled and neglected. The difference between yielding the integral contribution of radiative heat transfer mechanism to overall heat transport. Results indicate that radiative component of heat transfer within pores is small for conditions representative of light water reactor fuel, typically less than 1% of total heat transport. It is much larger, however, for conditions present in liquid metal fast breeder reactor fuel; during restructuring of this fuel type early in life, the radiative heat transfer mode was shown to contribute as much as 10-20% of total heat transport in hottest regions of fuel.
Heat transfer coefficients for staggered arrays of short pin fins
NASA Technical Reports Server (NTRS)
Vanfossen, G. J.
1981-01-01
Short pin fins are often used to increase that heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).
Heat transfer coefficients for staggered arrays of short pin fins
NASA Technical Reports Server (NTRS)
Vanfossen, G. J.
1981-01-01
Short pin fins are often used to increase the heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).
Flow and heat transfer enhancement in tube heat exchangers
NASA Astrophysics Data System (ADS)
Sayed Ahmed, Sayed Ahmed E.; Mesalhy, Osama M.; Abdelatief, Mohamed A.
2015-11-01
The performance of heat exchangers can be improved to perform a certain heat-transfer duty by heat transfer enhancement techniques. Enhancement techniques can be divided into two categories: passive and active. Active methods require external power, such as electric or acoustic field, mechanical devices, or surface vibration, whereas passive methods do not require external power but make use of a special surface geometry or fluid additive which cause heat transfer enhancement. The majority of commercially interesting enhancement techniques are passive ones. This paper presents a review of published works on the characteristics of heat transfer and flow in finned tube heat exchangers of the existing patterns. The review considers plain, louvered, slit, wavy, annular, longitudinal, and serrated fins. This review can be indicated by the status of the research in this area which is important. The comparison of finned tubes heat exchangers shows that those with slit, plain, and wavy finned tubes have the highest values of area goodness factor while the heat exchanger with annular fin shows the lowest. A better heat transfer coefficient ha is found for a heat exchanger with louvered finned and thus should be regarded as the most efficient one, at fixed pumping power per heat transfer area. This study points out that although numerous studies have been conducted on the characteristics of flow and heat transfer in round, elliptical, and flat tubes, studies on some types of streamlined-tubes shapes are limited, especially on wing-shaped tubes (Sayed Ahmed et al. in Heat Mass Transf 50: 1091-1102, 2014; in Heat Mass Transf 51: 1001-1016, 2015). It is recommended that further detailed studies via numerical simulations and/or experimental investigations should be carried out, in the future, to put further insight to these fin designs.
"Nanotechnology Enabled Advanced Industrial Heat Transfer Fluids"
Dr. Ganesh Skandan; Dr. Amit Singhal; Mr. Kenneth Eberts; Mr. Damian Sobrevilla; Prof. Jerry Shan; Stephen Tse; Toby Rossmann
2008-06-12
ABSTRACT Nanotechnology Enabled Advanced industrial Heat Transfer Fluids” Improving the efficiency of Industrial Heat Exchangers offers a great opportunity to improve overall process efficiencies in diverse industries such as pharmaceutical, materials manufacturing and food processing. The higher efficiencies can come in part from improved heat transfer during both cooling and heating of the material being processed. Additionally, there is great interest in enhancing the performance and reducing the weight of heat exchangers used in automotives in order to increase fuel efficiency. The goal of the Phase I program was to develop nanoparticle containing heat transfer fluids (e.g., antifreeze, water, silicone and hydrocarbon-based oils) that are used in transportation and in the chemical industry for heating, cooling and recovering waste heat. Much work has been done to date at investigating the potential use of nanoparticle-enhanced thermal fluids to improve heat transfer in heat exchangers. In most cases the effect in a commercial heat transfer fluid has been marginal at best. In the Phase I work, we demonstrated that the thermal conductivity, and hence heat transfer, of a fluid containing nanoparticles can be dramatically increased when subjected to an external influence. The increase in thermal conductivity was significantly larger than what is predicted by commonly used thermal models for two-phase materials. Additionally, the surface of the nanoparticles was engineered so as to have a minimal influence on the viscosity of the fluid. As a result, a nanoparticle-laden fluid was successfully developed that can lead to enhanced heat transfer in both industrial and automotive heat exchangers
Periodic Heat Transfer at Small Pressure Fluctuations
NASA Technical Reports Server (NTRS)
Pfriem, H.
1943-01-01
The effect of cyclic gas pressure variations on the periodic heat transfer at a flat wall is theoretically analyzed and the differential equation describing the process and its solution for relatively. Small pressure fluctuations developed, thus explaining the periodic heat cycle between gas and wall surface. The processes for pure harmonic pressure and temperature oscillations, respectively, in the gas space are described by means of a constant heat transfer coefficient and the equally constant phase angle between the appearance of the maximum values of the pressure and heat flow most conveniently expressed mathematically in the form of a complex heat transfer coefficient. Any cyclic pressure oscillations, can be reduced by Fourier analysis to harmonic oscillations, which result in specific, mutual relationships of heat-transfer coefficients and phase angles for the different harmonics.
Phase Change Heat Transfer Device for Process Heat Applications
Piyush Sabharwall; Mike Patterson; Vivek Utgikar; Fred Gunnerson
2010-10-01
The next generation nuclear plant (NGNP) will most likely produce electricity and process heat, with both being considered for hydrogen production. To capture nuclear process heat, and transport it to a distant industrial facility requires a high temperature system of heat exchangers, pumps and/or compressors. The heat transfer system is particularly challenging not only due to the elevated temperatures (up to approx.1300 K) and industrial scale power transport (=50MW), but also due to a potentially large separation distance between the nuclear and industrial plants (100+m) dictated by safety and licensing mandates. The work reported here is the preliminary analysis of two-phase thermosyphon heat transfer performance with alkali metals. A thermosyphon is a thermal device for transporting heat from one point to another with quite extraordinary properties. In contrast to single-phased forced convective heat transfer via ‘pumping a fluid’, a thermosyphon (also called a wickless heat pipe) transfers heat through the vaporization/condensing process. The condensate is further returned to the hot source by gravity, i.e., without any requirement of pumps or compressors. With this mode of heat transfer, the thermosyphon has the capability to transport heat at high rates over appreciable distances, virtually isothermally and without any requirement for external pumping devices. Two-phase heat transfer by a thermosyphon has the advantage of high enthalpy transport that includes the sensible heat of the liquid, the latent heat of vaporization, and vapor superheat. In contrast, single-phase forced convection transports only the sensible heat of the fluid. Additionally, vapor-phase velocities within a thermosyphon are much greater than single-phase liquid velocities within a forced convective loop. Thermosyphon performance can be limited by the sonic limit (choking) of vapor flow and/or by condensate entrainment. Proper thermosyphon requires analysis of both.
Gopinath, A.; Sadhal, S.S.; Jones, P.D.; Seyed-Yagoobi, J.; Woodbury, K.A.
1996-12-31
In the first section on heat transfer in microgravity, the papers cover phase-change phenomena and thermocapillary flows and surface effects. In the second section, several papers cover solution methods for radiative heat transfer while the rest cover heat transfer in low-temperature environments. The last section covers papers containing valuable information for thermal contact conductance of various materials plus papers on inverse problems in heat transfer. Separate abstracts were prepared for most papers in this volume.
Heat and mass transfer considerations in advanced heat pump systems
Panchal, C.B.; Bell, K.J.
1992-01-01
Advanced heat-pump cycles are being investigated for various applications. However, the working media and associated thermal design aspects require new concepts for maintaining high thermal effectiveness and phase equilibrium for achieving maximum possible thermodynamic advantages. In the present study, the heat- and mass-transfer processes in two heat-pump systems -- those based on absorption processes, and those using refrigerant mixtures -- are analyzed. The major technical barriers for achieving the ideal performance predicted by thermodynamic analysis are identified. The analysis provides general guidelines for the development of heat- and mass-transfer equipment for advanced heat-pump systems.
Heat and mass transfer considerations in advanced heat pump systems
Panchal, C.B.; Bell, K.J.
1992-08-01
Advanced heat-pump cycles are being investigated for various applications. However, the working media and associated thermal design aspects require new concepts for maintaining high thermal effectiveness and phase equilibrium for achieving maximum possible thermodynamic advantages. In the present study, the heat- and mass-transfer processes in two heat-pump systems -- those based on absorption processes, and those using refrigerant mixtures -- are analyzed. The major technical barriers for achieving the ideal performance predicted by thermodynamic analysis are identified. The analysis provides general guidelines for the development of heat- and mass-transfer equipment for advanced heat-pump systems.
Thermodynamics of Flow Boiling Heat Transfer
NASA Astrophysics Data System (ADS)
Collado, F. J.
2003-05-01
Convective boiling in sub-cooled water flowing through a heated channel is essential in many engineering applications where high heat flux needs to be accommodated. It has been customary to represent the heat transfer by the boiling curve, which shows the heat flux versus the wall-minus-saturation temperature difference. However it is a rather complicated problem, and recent revisions of two-phase flow and heat transfer note that calculated values of boiling heat transfer coefficients present many uncertainties. Quite recently, the author has shown that the average thermal gap in the heated channel (the wall temperature minus the average temperature of the coolant) was tightly connected with the thermodynamic efficiency of a theoretical reversible engine placed in this thermal gap. In this work, whereas this correlation is checked again with data taken by General Electric (task III) for water at high pressure, a possible connection between this wall efficiency and the reversible-work theorem is explored.
Droplet heat transfer and chemical reactions during direct containment heating
Baker, L. Jr.
1986-01-01
A simplified model of heat transfer and chemical reaction has been adapted to evaluate the expected behavior of droplets containing unreacted Zircaloy and stainless steel moving through the containment atmosphere during postulated accidents involving direct containment heating. The model includes internal and external diffusive resistances to reaction. The results indicate that reactions will be incomplete for many conditions characteristic of direct containment heating sequences.
Variable-Conductance Heat-Transfer Module
NASA Technical Reports Server (NTRS)
Hewitt, D. R.
1984-01-01
Working lengths of heat pipes electronically controlled. Rate of heat transfer controlled by electrical heaters shorten effective working lengths of heat pipes. Concept not limited to right circular cylindrical shape. Concept adaptable to terrestrial instruments or processes in which atmospheres or fluids must be cooled and returned to instruments or processes at fixed lower temperatures.
Estimation of radiative heat transfer using a geometric human model.
Kakuta, N; Yokoyama, S; Nakamura, M; Mabuchi, K
2001-03-01
In order to provide a detailed estimate of radiative heat transfer between a human body and its surrounding environment, we have developed a geometric model of a human form and an algorithm. The model closely resembles the actual shape of a human body and is composed of small quadrilateral surfaces. Dealing with an object or a space with an arbitrary shape, the developed algorithm can judge efficiently whether there is an obstruction between a pair of surfaces. As a result, the angle factors between a pair of surfaces that only occur during radiative heat transfer can be defined. The distribution of the radiative heat transfer rates shows the characteristics of body shape and variations in posture. PMID:11327500
Near field heat transfer in superlattices
NASA Astrophysics Data System (ADS)
Esquivel-Sirvent, Raul
2015-03-01
I present a theoretical calculation of the near field heat transfer between super lattices made of alternative layers of both metallic and semiconducting materials. The calculation of the near field transfer requires the knowledge of the reflectivities, that are obtained by calculating the surface impedance of the super lattice. Depending on the periodicity of the lattice and the dielectric function of the materials the near field heat transfer can be modulated or engineered. Additional control on the heat transfer is achieved by introducing defects in the superlattice. The results are extended to include photonic hypercrystals that effectively behave like a hyperbolic metamaterial even in the near field (1), where the tuning of the heat transfer is modified by Partial Support from DGAPA-UNAM project IN 111214.
Heat Transfer of Nanofluid in a Double Pipe Heat Exchanger
Aghayari, Reza; Maddah, Heydar; Zarei, Malihe; Dehghani, Mehdi; Kaskari Mahalle, Sahar Ghanbari
2014-01-01
This paper investigates the enhancement of heat transfer coefficient and Nusselt number of a nanofluid containing nanoparticles (γ-AL2O3) with a particle size of 20 nm and volume fraction of 0.1%–0.3% (V/V). Effects of temperature and concentration of nanoparticles on Nusselt number changes and heat transfer coefficient in a double pipe heat exchanger with counter turbulent flow are investigated. Comparison of experimental results with valid theoretical data based on semiempirical equations shows an acceptable agreement. Experimental results show a considerable increase in heat transfer coefficient and Nusselt number up to 19%–24%, respectively. Also, it has been observed that the heat transfer coefficient increases with the operating temperature and concentration of nanoparticles. PMID:27433521
NASA Technical Reports Server (NTRS)
Kirby, Mark S.; Hansman, R. John, Jr.
1988-01-01
The heat transfer behavior of accreting ice surfaces in natural (flight test) and simulated (wind tunnel) cloud icing conditions were studied. Observations of wet and dry ice growth regimes as measured by ultrasonic pulse echo techniques were made. Observed wet and dry ice growth regimes at the stagnation point of a cylinder were compared with those predicted using a quasi steady state heat balance model. A series of heat transfer coefficients were employed by the model to infer the local heat transfer behavior of the actual ice surfaces. The heat transfer in the stagnation region was generally inferred to be higher in wind tunnel icing tests than in natural flight icing conditions.
Pumped two-phase heat transfer loop
NASA Technical Reports Server (NTRS)
Edelstein, Fred
1988-01-01
A pumped loop two-phase heat transfer system, operating at a nearly constant temperature throughout, includes several independently operating grooved capillary heat exchanger plates supplied with working fluid through independent flow modulation valves connected to a liquid supply line, a vapor line for collecting vapor from the heat exchangers, a condenser between the vapor and the liquid lines, and a fluid circulating pump between the condenser and the heat exchangers.
Pumped two-phase heat transfer loop
NASA Technical Reports Server (NTRS)
Edelstein, Fred (Inventor)
1987-01-01
A pumped loop two-phase heat transfer system, operating at a nearly constant temperature throughout, includes a plurality of independently operating grooved capillary heat exchanger plates supplied with working fluid through independent flow modulation valves connected to a liquid supply line, a vapor line for collecting vapor from the heat exchangers, a condenser between the vapor and the liquid lines, and a fluid circulating pump between the condenser and the heat exchangers.
Heat transfer peculiarities in supersonic flows
NASA Astrophysics Data System (ADS)
Borovoi, V. Ia.; Brazhko, V. N.; Maikapar, G. I.; Skuratov, A. S.; Struminskaia, I. V.
1992-12-01
A method of heat transfer and gas flow investigation based on the application of thermal sensitive coatings or thermocouple sensors and various visualization techniques is described. The thermal sensitive coatings and visualization reveal heat transfer peculiarities, and the complex nature of the method contributes to understanding the processes and generalization of quantitative results. Data concerning heat transfer on the leeward side of a blunt cone in the regions of the shock-wave boundary layer and bow wave interaction, in gaps and cavities of the orbiter's thermal insulation, and in the vicinity of them, are presented.
Passive heat transfer means for nuclear reactors
Burelbach, James P.
1984-01-01
An improved passive cooling arrangement is disclosed for maintaining adjacent or related components of a nuclear reactor within specified temperature differences. Specifically, heat pipes are operatively interposed between the components, with the vaporizing section of the heat pipe proximate the hot component operable to cool it and the primary condensing section of the heat pipe proximate the other and cooler component operable to heat it. Each heat pipe further has a secondary condensing section that is located outwardly beyond the reactor confinement and in a secondary heat sink, such as air ambient the containment, that is cooler than the other reactor component. Means such as shrouding normally isolated the secondary condensing section from effective heat transfer with the heat sink, but a sensor responds to overheat conditions of the reactor to open the shrouding, which thereby increases the cooling capacity of the heat pipe. By having many such heat pipes, an emergency passive cooling system is defined that is operative without electrical power.
Determination of the heat transfer coefficients in transient heat conduction
NASA Astrophysics Data System (ADS)
Nho Hào, Dinh; Thanh, Phan Xuan; Lesnic, D.
2013-09-01
The determination of the space- or time-dependent heat transfer coefficient which links the boundary temperature to the heat flux through a third-kind Robin boundary condition in transient heat conduction is investigated. The reconstruction uses average surface temperature measurements. In both cases of the space- or time-dependent unknown heat transfer coefficient the inverse problems are nonlinear and ill posed. Least-squares penalized variational formulations are proposed and new formulae for the gradients are derived. Numerical results obtained using the nonlinear conjugate gradient method combined with a boundary element direct solver are presented and discussed.
Heat transfer behavior of molten nitrate salt
NASA Astrophysics Data System (ADS)
Das, Apurba K.; Clark, Michael M.; Teigen, Bard C.; Fiveland, Woodrow A.; Anderson, Mark H.
2016-05-01
The usage of molten nitrate salt as heat transfer fluid and thermal storage medium decouples the generation of electricity from the variable nature of the solar resource, allowing CSP plants to avoid curtailment and match production with demand. This however brings some unique challenges for the design of the molten salt central receiver (MSCR). An aspect critical to the use of molten nitrate (60wt%/40wt% - NaNO3/KNO3) salt as heat transfer fluid in the MSCR is to understand its heat transfer behavior. Alstom collaborated with the University of Wisconsin to conduct a series of experiments and experimentally determined the heat transfer coefficients of molten nitrate salt up to high Reynolds number (Re > 2.0E5) and heat flux (q″ > 1000 kW/m2), conditions heretofore not reported in the literature. A cartridge heater instrumented with thermocouples was installed inside a stainless steel pipe to form an annular test section. The test section was installed in the molten salt flow loop at the University of Wisconsin facility, and operated over a range of test conditions to determine heat transfer data that covered the expected operating regime of a practical molten salt receiver. Heat transfer data were compared to widely accepted correlations found in heat transfer literature, including that of Gnielinski. At lower Reynolds number conditions, the results from this work concurred with the molten salt heat transfer data reported in literature and followed the aforementioned correlations. However, in the region of interest for practical receiver design, the correlations did not accurately model the experimentally determined heat transfer data. Two major effects were observed: (i) all other factors remaining constant, the Nusselt numbers gradually plateaued at higher Reynolds number; and (ii) at higher Reynolds number a positive interaction of heat flux on Nusselt number was noted. These effects are definitely not modeled by the existing correlations. In this paper a new
Heat transfer near turbine nozzle endwall.
Chyu, M K
2001-05-01
This paper gives an overview and reviews recent findings concerning turbine endwall cooling in the literature. The text below begins with a brief discussion of the secondary flows and heat transfer around cascade endwall. This will be followed by a review of recent developments in cooling concepts and related heat transfer results. Key topics include: film cooling, upstream bleeding, endwall contouring, and leakage through component interfaces. PMID:11460636
Nanoparticle enhanced ionic liquid heat transfer fluids
Fox, Elise B.; Visser, Ann E.; Bridges, Nicholas J.; Gray, Joshua R.; Garcia-Diaz, Brenda L.
2014-08-12
A heat transfer fluid created from nanoparticles that are dispersed into an ionic liquid is provided. Small volumes of nanoparticles are created from e.g., metals or metal oxides and/or alloys of such materials are dispersed into ionic liquids to create a heat transfer fluid. The nanoparticles can be dispersed directly into the ionic liquid during nanoparticle formation or the nanoparticles can be formed and then, in a subsequent step, dispersed into the ionic liquid using e.g., agitation.
Three-dimensional nonsteady heat-transfer analysis of an indirect heating furnace
Ito, H.; Umeda, Y.; Nakamura, Y.; Wantanabe, T.; Mitutani, T. ); Arai, N.; Hasatani, M. )
1991-01-01
This paper reports on an accurate design method for industrial furnaces from the viewpoint of heat transfer. The authors carried out a three-dimensional nonsteady heat-transfer analysis for a practical-size heat- treatment furnace equipped with radiant heaters. The authors applied three software package programs, STREAM, MORSE, and TRUMP, for the analysis of the combined heat-transfer problems of radiation, conduction, and convection. The authors also carried out experiments of the heating of a charge consisting of packed bolts. The authors found that the air swirled inside the furnace. As for the temperature in each part in the furnace, analytical results were generally in close agreement with the experimental ones. This suggests that our analytical method is useful for a fundamental heat- transfer-based design of a practical-size industrial furnace with an actual charge such as packed bolts. As for the temperature distribution inside the bolt charge (work), the analytical results were also in close agreement with the experimental ones. Consequently, it was found that the heat transfer in the bolt charge could be described with an effective thermal conductivity.
Heat and mass transfer in materials processing
NASA Astrophysics Data System (ADS)
Tanasawa, Ichiro; Lior, Noam
Various papers on heat and mass transfer in materials processing are presented. The topics addressed include: heat transfer in plasma spraying, structure of ultrashort pulse plasma for CVD processing, heat flow and thermal contraction during plasma spray deposition, metal melting process by laser heating, improved electron beam weld design and control with beam current profile measurements, transport phenomena in laser materials processing, perspectives on integrated modeling of transport processes in semiconductor crystal growth, numerical simulation of natural convection in crystal growth in space and on the earth, conjugate heat transfer in crystal growth, effects of convection on the solidification of binary mixtures. Also discussed are: heat transfer in in-rotating-liquid-spinning process, thermal oscillations in materials processing, modeling and simulation of manufacturing processes of advanced composite materials, reaction engineering principles of combustion synthesis of advanced materials, numerical evaluation of the physical properties of magnetic fluids suitable for heat transfer control, and measurement techniques of thermophysical properties of high temperature melts. (For individual items see A93-10827 to A93-10843)
Examination of Liquid Fluoride Salt Heat Transfer
Yoder Jr, Graydon L
2014-01-01
The need for high efficiency power conversion and energy transport systems is increasing as world energy use continues to increase, petroleum supplies decrease, and global warming concerns become more prevalent. There are few heat transport fluids capable of operating above about 600oC that do not require operation at extremely high pressures. Liquid fluoride salts are an exception to that limitation. Fluoride salts have very high boiling points, can operate at high temperatures and low pressures and have very good heat transfer properties. They have been proposed as coolants for next generation fission reactor systems, as coolants for fusion reactor blankets, and as thermal storage media for solar power systems. In each case, these salts are used to either extract or deliver heat through heat exchange equipment, and in order to design this equipment, liquid salt heat transfer must be predicted. This paper discusses the heat transfer characteristics of liquid fluoride salts. Historically, heat transfer in fluoride salts has been assumed to be consistent with that of conventional fluids (air, water, etc.), and correlations used for predicting heat transfer performance of all fluoride salts have been the same or similar to those used for water conventional fluids an, water, etc). A review of existing liquid salt heat transfer data is presented, summarized, and evaluated on a consistent basis. Less than 10 experimental data sets have been found in the literature, with varying degrees of experimental detail and measured parameters provided. The data has been digitized and a limited database has been assembled and compared to existing heat transfer correlations. Results vary as well, with some data sets following traditional correlations; in others the comparisons are less conclusive. This is especially the case for less common salt/materials combinations, and suggests that additional heat transfer data may be needed when using specific salt eutectics in heat transfer
Interactive Heat Transfer Simulations for Everyone
ERIC Educational Resources Information Center
Xie, Charles
2012-01-01
Heat transfer is widely taught in secondary Earth science and physics. Researchers have identified many misconceptions related to heat and temperature. These misconceptions primarily stem from hunches developed in everyday life (though the confusions in terminology often worsen them). Interactive computer simulations that visualize thermal energy,…
Heat transfer coefficient of nanofluids in minichannel heat sink
NASA Astrophysics Data System (ADS)
Utomo, Adi T.; Zavareh, Ashkan I. T.; Poth, Heiko; Wahab, Mohd; Boonie, Mohammad; Robbins, Phillip T.; Pacek, Andrzej W.
2012-09-01
Convective heat transfer in a heat sink consisting of rectangular minichannels and cooled with alumina and titania nanofluids has been investigated experimentally and numerically. Numerical simulations were carried out in a three dimensional domain employing homogeneous mixture model with effective thermo-physical properties of nanofluids. The predictions of base temperature profiles of the heat sink cooled with both water and nanofluids agree well with the experimental data. Experimental and numerical results show that the investigated nanofluids neither exhibits unusual enhancement of heat transfer coefficient nor decreases the heat sink base temperature. Although both nanofluids showed marginal thermal conductivity enhancements, the presence of solid nanoparticles lowers the specific heat capacity of nanofluids offseting the advantage of thermal conductivity enhancement. For all investigated flow rates, the Nusselt number of both nanofluids overlaps with that of water indicating that both nanofluids behave like single-phase fluids.
Concurrent implementation of the Crank-Nicolson method for heat transfer analysis
NASA Technical Reports Server (NTRS)
Ransom, J. B.; Fulton, R. E.
1985-01-01
To exploit the significant gains in computing speed provided by Multiple Instruction Multiple Data (MIMD) computers, concurrent methods for practical problems need to be investigated and test problems implemented on actual hardware. One such problem class is heat transfer analysis which is important in many aerospace applications. This paper compares the efficiency of two alternate implementations of heat transfer analysis on an experimental MIMD computer called the Finite Element Machine (FEM). The implicit Crank-Nicolson method is used to solve concurrently the heat transfer equations by both iterative and direct methods. Comparison of actual timing results achieved for the two methods and their significance relative to more complex problems are discussed.
NASA Technical Reports Server (NTRS)
Sabin, C. M.; Poppendiek, H. F.
1971-01-01
A number of heat transfer and fluid flow mechanisms that control once-through, forced convection potassium boiling are studied analytically. The topics discussed are: (1) flow through tubes containing helical wire inserts, (2) motion of droplets entrained in vapor flow, (3) liquid phase distribution in boilers, (4) temperature distributions in boiler tube walls, (5) mechanisms of heat transfer regime change, and (6) heat transfer in boiler tubes. Whenever possible, comparisons of predicted and actual performances are made. The model work presented aids in the prediction of operating characteristics of actual boilers.
Heat Transfer to Fuel Sprays Injected into Heated Gases
NASA Technical Reports Server (NTRS)
Selden, Robert F; Spencer, Robert C
1938-01-01
This report presents the results of a study made of the influence of several variables on the pressure decrease accompanying injection of a relatively cool liquid into a heated compressed gas. Indirectly, this pressure decrease and the time rate of change of it are indicative of the total heat transferred as well as the rate of heat transfer between the gas and the injected liquid. Air, nitrogen, and carbon dioxide were used as ambient gases; diesel fuel and benzene were the injected liquids. The gas densities and gas-fuel ratios covered approximately the range used in compression-ignition engines. The gas temperatures ranged from 150 degrees c. to 350 degrees c.
Heat transfer studies. Quarterly report
Boehm, R.; Chen, Y.T.; Ma, L.
1995-04-20
Nitrogen gas has been replaced by room air in the extension of multi-phase models to sub-residual saturation experiments on drying. The TOUGH2 code has been used to simulate the same problem with the identical boundary conditions. A constant heat flux boundary condition on the heater has been performed in the repository drift experiment. The desired constant heat flux can produce a steady-state heater temperature ({approx}238{degrees}C) close to the constant heater surface temperature used before. What occurs in the air annulus and in the porous medium with the different thermal boundary conditions and water quantities is reported.
Interactive Heat Transfer Simulations for Everyone
NASA Astrophysics Data System (ADS)
Xie, Charles
2012-04-01
Heat transfer is widely taught in secondary Earth science and physics. Researchers have identified many misconceptions related to heat and temperature. These misconceptions primarily stem from hunches developed in everyday life (though the confusions in terminology often worsen them). Interactive computer simulations that visualize thermal energy, temperature distribution, and heat transfer may provide a straightforward method for teaching and learning these concepts. Through interacting with visual representations of the concepts and observing how they respond to manipulations, the misconceptions may be dispelled more effectively. This paper presents a new educational simulation tool called Energy2D developed to explore this idea.
Heat transfer characteristics for disk fans
NASA Astrophysics Data System (ADS)
Prikhodko, Yu. M.; Chekhov, V. P.; Fomichev, V. P.
2014-08-01
Multiple-disk fans belong to the class of friction machines; they can be designed in two variants: centrifugal disk fans and diametrical disk fans. Flow patterns in these two types of machines are different, and they possess different heat transfer characteristics. The paper presents results of experimental study for a centrifugal disk fan under atmospheric pressure with air taken as working gas. The radial temperature distribution for a disk was obtained at different rotation speed of the rotor and different heating of the disks. Heat transfer characteristics of a centrifugal disk fan and a diametrical disk fan were compared. The research results demonstrate a higher heat transfer efficiency for centrifugal design versus diametrical disk design.
Indirect evaporative coolers with enhanced heat transfer
Kozubal, Eric; Woods, Jason; Judkoff, Ron
2015-09-22
A separator plate assembly for use in an indirect evaporative cooler (IEC) with an air-to-air heat exchanger. The assembly includes a separator plate with a first surface defining a dry channel and a second surface defining a wet channel. The assembly includes heat transfer enhancements provided on the first surface for increasing heat transfer rates. The heat transfer enhancements may include slit fins with bodies extending outward from the first surface of separator plate or may take other forms including vortex generators, offset strip fins, and wavy fins. In slit fin implementations, the separator plate has holes proximate to each of the slit fins, and the separator plate assembly may include a sealing layer applied to the second surface of the separator plate to block air flow through the holes. The sealing layer can be a thickness of adhesive, and a layer of wicking material is applied to the adhesive.
Gau, C.; Wu, J.M.; Liang, C.Y.
1999-11-01
Experiments are performed to study the flow structure and heat transfer over a heated oscillating cylinder. Both flow visualization using a smoke wire and local heat transfer measurements around the cylinder were made. The excitation frequencies of the cylinder are selected at F{sub e}/F{sub n} = 0, 0.5, 1, 1.5, 2, 2.5, and 3. These include excitations at harmonic, subharmonic, superharmonic, and non harmonic frequencies. Synchronization of vortex shedding with the cylinder excitation occurs not only at F{sub e}/F{sub n} = 1 but also at F{sub e}/F{sub n} = 3, which can greatly enhance the heat transfer. The simultaneous enhancement of heat transfer at the stagnation point, its downstream region, and the wake region of the flow suggests that different modes of instabilities occurring in the shear layer of the near wake are actually initiated and amplified far upstream in the stagnation point, which were suppressed in the accelerated flow region and re-amplified in the decelerated flow region. As long as the dominant mode of the instability is amplified by the excitation of cylinder, enhancement of heat transfer can be obtained. During the experiments, the Reynolds numbers vary from 1,600 to 4,800, the ratios of oscillation amplitude to diameter of the cylinder from 0.064 to 0.016.
Capillary-Condenser-Pumped Heat-Transfer Loop
NASA Technical Reports Server (NTRS)
Silverstein, Calvin C.
1989-01-01
Heat being transferred supplies operating power. Capillary-condenser-pumped heat-transfer loop similar to heat pipe and to capillary-evaporator-pumped heat-transfer loop in that heat-transfer fluid pumped by evaporation and condensation of fluid at heat source and sink, respectively. Capillary condenser pump combined with capillary evaporator pump to form heat exchanger circulating heat-transfer fluids in both loops. Transport of heat more nearly isothermal. Thermal stress in loop reduced, and less external surface area needed in condenser section for rejection of heat to heat sink.
Comparative Analysis of Thermoeconomic Evaluation Criteria for an Actual Heat Engine
NASA Astrophysics Data System (ADS)
Özel, Gülcan; Açıkkalp, Emin; Savaş, Ahmet Fevzi; Yamık, Hasan
2016-07-01
In the present study, an actual heat engine is investigated by using different thermoeconomic evaluation criteria in the literature. A criteria that has not been investigated in detail is considered and it is called as ecologico-economical criteria (F_{EC}). It is the difference of power cost and exergy destruction rate cost of the system. All four criteria are applied to an irreversible Carnot heat engine, results are presented numerically and some suggestions are made.
Modeling microscale heat transfer using Calore.
Gallis, Michail A.; Rader, Daniel John; Wong, Chung-Nin Channy; Bainbridge, Bruce L.; Torczynski, John Robert; Piekos, Edward Stanley
2005-09-01
Modeling microscale heat transfer with the computational-heat-transfer code Calore is discussed. Microscale heat transfer problems differ from their macroscopic counterparts in that conductive heat transfer in both solid and gaseous materials may have important noncontinuum effects. In a solid material, three noncontinuum effects are considered: ballistic transport of phonons across a thin film, scattering of phonons from surface roughness at a gas-solid interface, and scattering of phonons from grain boundaries within the solid material. These processes are modeled for polycrystalline silicon, and the thermal-conductivity values predicted by these models are compared to experimental data. In a gaseous material, two noncontinuum effects are considered: ballistic transport of gas molecules across a thin gap and accommodation of gas molecules to solid conditions when reflecting from a solid surface. These processes are modeled for arbitrary gases by allowing the gas and solid temperatures across a gas-solid interface to differ: a finite heat transfer coefficient (contact conductance) is imposed at the gas-solid interface so that the temperature difference is proportional to the normal heat flux. In this approach, the behavior of gas in the bulk is not changed from behavior observed under macroscopic conditions. These models are implemented in Calore as user subroutines. The user subroutines reside within Sandia's Source Forge server, where they undergo version control and regression testing and are available to analysts needing these capabilities. A Calore simulation is presented that exercises these models for a heated microbeam separated from an ambient-temperature substrate by a thin gas-filled gap. Failure to use the noncontinuum heat transfer models for the solid and the gas causes the maximum temperature of the microbeam to be significantly underpredicted.
Simplified models for heat transfer in rooms
NASA Astrophysics Data System (ADS)
Graca, Guilherme C. C. Carrilho Da
Buildings protect their occupants from the outside environment. As a semi-enclosed environment, buildings tend to contain the internally generated heat and air pollutants, as well as the solar and conductive heat gains that can occur in the facade. In the warmer months of the year this generally leads to overheating, creating a need for a cooling system. Ventilation air replaces contaminated air in the building and is often used as the dominant medium for heat transfer between indoor and outdoor environments. The goal of the research presented in this thesis is to develop a better understanding of the important parameters in the performance of ventilation systems and to develop simplified convective heat transfer models. The general approach used in this study seeks to capture the dominant physical processes for these problems with first order accuracy, and develop simple models that show the correct system behavior trends. Dimensional analysis, in conjunction with simple momentum and energy conservation, scaled model experiments and numerical simulations, is used to improve airflow and heat transfer rate predictions in both single and multi room ventilation systems. This study includes the three commonly used room ventilation modes: mixing, displacement and cross-ventilation. A new modeling approach to convective heat transfer between the building and the outside is presented: the concept of equivalent room heat transfer coefficient. The new model quantifies the reduction in heat transfer between ventilation air and internal room surfaces caused by limited thermal capacity and temperature variation of the air for the three modes studied. Particular emphasis is placed on cross-ventilation, and on the development of a simple model to characterize the airflow patterns that occur in this case. The implementation of the models in a building thermal simulation software tool is presented as well as comparisons between model predictions, experimental results and complex
A heat transfer model of a horizontal ground heat exchanger
NASA Astrophysics Data System (ADS)
Mironov, R. E.; Shtern, Yu. I.; Shtern, M. Yu.; Rogachev, M. S.
2016-04-01
Ground-source heat pumps are gaining popularity in Eastern Europe, especially those which are using the horizontal ground heat exchanger (GHX). Due to the difficulty of accessing GHX after the installation, materials and the quality of the installation must satisfy the very high requirements. An inaccurate calculation of GHX can be the reason of a scarcity of heat power in a crucial moment. So far, there isn't any appropriate mathematical description of the horizontal GHX which takes into account the mutual influence of GHX pipes on each other. To solve this problem we used the temperature wave approach. As a result, a mathematical model which describes the dependence of the heat transfer rate per unit length of the horizontal GHX pipe on the thermal properties of soil, operating time of GHX and the distance between pipes was obtained. Using this model, heat transfer rates per unit length of a horizontal GHX were plotted as functions of the distance between pipes and operating time. The modeling shows that heat transfer rates decreases rapidly with the distance between pipes lower then 2 meters. After the launch of heat pump, heat power of GHX is reduced during the first 20 - 30 days and get steady after that. The obtained results correlate with experimental data. Therefore the proposed mathematical model can be used to design a horizontal GHX with the optimal characteristics, and predict its capability during operation.
Characteristics of Transient Boiling Heat Transfer
Liu, Wei; Monde, Masanori; Mitsutake, Y.
2002-07-01
In this paper, one dimensional inverse heat conduction solution is used for a measurement of pool boiling curve. The experiments are performed under atmospheric pressure for copper, brass, carbon steel and gold. Boiling curves, including unsteady transition boiling region, are found can be traced fairly well from a simple experiment system by solving inverse heat conduction solution. Boiling curves for steady heating and transient heating, for heating process and cooling process are compared. Surface behavior around CHF point, transition boiling and film-boiling regions are observed by using a high-speed camera. The results show the practicability of the inverse heat conduction solution in tracing boiling curve and thereby supply us a new way in boiling heat transfer research. (authors)
Heat transfer in pressurized circulating fluidized beds
Wirth, K.E.
1997-12-31
The wall-to-suspension heat transfer in circulating fluidized beds (CFBs) operated at almost atmospheric pressure depends on the fluid mechanics immediately near the wall and on the thermal properties of the gas used. No influence of the superficial gas velocity adjusted is present. Consequently, the wall-to-suspension heat transfer coefficient in the form of the Nusselt number can be described by the Archimedes number of the gas-solid-system and the pressure drop number. The last number relates the cross-sectional average solids concentration to the solids concentration at minimum fluidization condition. However, with pressurized CFBs an influence of the superficial gas velocity on the wall-to-suspension heat transfer can be observed. Normalizing the superficial gas velocity in the form of the particle Froude number, two cases for the heat transfer in pressurized CFBs can be detected: with small particle Froude numbers (smaller than four) the same flow behavior and consequently the same heat transfer correlation is valid as it is for CFBs operated at almost atmospheric conditions; and with high particle Froude numbers (for example higher than four) the flow behavior immediately near the heat exchanger surface (CFB wall) can change. Instead of curtains of solids falling down with almost atmospheric pressure swirls of gas and solids can occur in the vicinity of the CFB wall when the static pressure is increased. With the change of the flow pattern near the CFB wall, i.e., the heat exchanger surface, a change of the heat transfer coefficient takes place. For the same Archimedes number, i.e., the same gas-solid system, and the same pressure drop number, i.e., the same cross-sectional average solids concentration, the Nusselt number, i.e., the heat transfer coefficient, increases when the flow pattern near the CFB wall changes from the curtain-type flow to that of the swirl-type flow. From experimentally obtained data in a cold running CFB a very simple correlation was
HOST turbine heat transfer program summary
NASA Technical Reports Server (NTRS)
Gladden, Herbert J.; Simoneau, Robert J.
1988-01-01
The objectives of the HOST Turbine Heat Transfer subproject were to obtain a better understanding of the physics of the aerothermodynamic phenomena and to assess and improve the analytical methods used to predict the flow and heat transfer in high temperature gas turbines. At the time the HOST project was initiated, an across-the-board improvement in turbine design technology was needed. A building-block approach was utilized and the research ranged from the study of fundamental phenomena and modeling to experiments in simulated real engine environments. Experimental research accounted for approximately 75 percent of the funding with the remainder going to analytical efforts. A healthy government/industry/university partnership, with industry providing almost half of the research, was created to advance the turbine heat transfer design technology base.
Heat transfer on accreting ice surfaces
NASA Technical Reports Server (NTRS)
Yamaguchi, Keiko; Hansman, R. John, Jr.
1990-01-01
Based on previous observations of glaze ice accretion, a 'Multi-Zone' model with distinct zones of different surface roughness is demonstrated. The use of surface roughness in the LEWICE ice accretion prediction code is examined. It was found that roughness is used in two ways: to determine the laminar to turbulent transition location and to calculate the turbulent heat transfer coefficient. A two zone version of the Multi-Zone model is implemented in the LEWICE code, and compared with experimental heat transfer coefficient and ice accretin results. The analysis of the boundary layer transition, surface roughness, and viscous flow field effects significantly increased the accuracy in predicting heat transfer coefficients. The Multi-Zone model was found to greatly improve the ice accretion prediction for the cases compared.
Heat transfer on accreting ice surfaces
NASA Technical Reports Server (NTRS)
Yamaguchi, Keiko; Hansman, R. John, Jr.
1993-01-01
Based on previous observations of glaze ice accretion on aircraft surfaces, a multizone model with distinct zones of different surface roughness is demonstrated. The use of surface roughness in the LEWICE ice accretion prediction code is examined. It was found that roughness is used in two ways: (1) to determine the laminar to turbulent boundary-layer transition location; and (2) to calculate the convective turbulent heat-transfer coefficient. A two-zone version of the multizone model is implemented in the LEWICE code, and compared with experimental convective heat-transfer coefficient and ice accretion results. The analysis of the boundary-layer transition, surface roughness, and viscous flowfield effects significantly increased the accuracy in predicting heat-transfer coefficients. The multizone model was found to significantly improve the ice accretion prediction for the cases compared.
Self supporting heat transfer element
Story, Grosvenor Cook; Baldonado, Ray Orico
2002-01-01
The present invention provides an improved internal heat exchange element arranged so as to traverse the inside diameter of a container vessel such that it makes good mechanical contact with the interior wall of that vessel. The mechanical element is fabricated from a material having a coefficient of thermal conductivity above about 0.8 W cm.sup.-1.degree. K.sup.-1 and is designed to function as a simple spring member when that member has been cooled to reduce its diameter to just below that of a cylindrical container or vessel into which it is placed and then allowed to warm to room temperature. A particularly important application of this invention is directed to a providing a simple compartmented storage container for accommodating a hydrogen absorbing alloy.
Axial flow heat exchanger devices and methods for heat transfer using axial flow devices
Koplow, Jeffrey P.
2016-02-16
Systems and methods described herein are directed to rotary heat exchangers configured to transfer heat to a heat transfer medium flowing in substantially axial direction within the heat exchangers. Exemplary heat exchangers include a heat conducting structure which is configured to be in thermal contact with a thermal load or a thermal sink, and a heat transfer structure rotatably coupled to the heat conducting structure to form a gap region between the heat conducting structure and the heat transfer structure, the heat transfer structure being configured to rotate during operation of the device. In example devices heat may be transferred across the gap region from a heated axial flow of the heat transfer medium to a cool stationary heat conducting structure, or from a heated stationary conducting structure to a cool axial flow of the heat transfer medium.
Enhanced boiling heat transfer using radial fins
NASA Astrophysics Data System (ADS)
Razelos, P.; Das, S.; Krikkis, R. N.
2008-04-01
A numerical bifurcation analysis is carried out in order to determine the solution structure of radial fins subjected to multi-boiling heat transfer mode. One-dimensional conduction is employed throughout the thermal analysis. The fluid heat transfer coefficient is temperature dependent on the three regimes of phase-change of the fluid. Six fin profiles, defined in the text, are considered. Multiplicity structure is obtained to determine different types of bifurcation diagrams, which describe the dependence of a state variable of the system like the temperature or the heat dissipation on the fin design parameters, conduction convection parameter (CCP) or base temperature difference (Δ T). Specifically, the effects of Δ T, CCP and Biot number are analyzed. The results are presented graphically, showing the significant behavioral features of the heat rejection mechanism.
Coolant passage heat transfer with rotation
NASA Astrophysics Data System (ADS)
Hajek, T. J.; Wagner, J.; Johnson, B. V.
1986-10-01
In current and advanced gas turbine engines, increased speeds, pressures and temperatures are used to reduce specific fuel consumption and increase thrust/weight ratios. Hence, the turbine airfoils are subjected to increased heat loads escalating the cooling requirements to satisfy life goals. The efficient use of cooling air requires that the details of local geometry and flow conditions be adequately modeled to predict local heat loads and the corresponding heat transfer coefficients. The objective of this program is to develop a heat transfer and pressure drop data base, computational fluid dynamic techniques and correlations for multi-pass rotating coolant passages with and without flow turbulators. The experimental effort is focused on the simulation of configurations and conditions expected in the blades of advanced aircraft high pressure turbines. With the use of this data base, the effects of Coriolis and buoyancy forces on the coolant side flow can be included in the design of turbine blades.
Metallized Gelled Propellant Heat Transfer Tests Analyzed
NASA Technical Reports Server (NTRS)
Palaszewski, Bryan A.
1997-01-01
A series of rocket engine heat transfer experiments using metallized gelled liquid propellants was conducted at the NASA Lewis Research Center. These experiments used a small 20- to 40-lbf thrust engine composed of a modular injector, an igniter, a chamber, and a nozzle. The fuels used were traditional liquid RP-1 and gelled RP-1 with 0-, 5-, and 55-wt % loadings of aluminum particles. Gaseous oxygen was used as the oxidizer. Heat transfer measurements were made with a rocket engine calorimeter chamber and nozzle with a total of 31 cooling channels. Each channel used water flow to carry heat away from the chamber and the attached thermocouples; flow meters allowed heat flux estimates at each of the 31 stations.
Heat transfer during evaporation on a small surface (Review)
NASA Astrophysics Data System (ADS)
Tolubinskii, V. I.; Antonenko, V. A.; Kudritskii, G. R.; Ostrovskii, Iu. N.
Experimental data in the literature on the intensity of heat transfer and critical heat loads associated with the boiling of a liquid on a small surface are examined. Various methods for intensifying heat transfer are discussed. Expressions are presented for calculating heat transfer coefficients and critical heat flux densities.
Heat transfer characteristics of an emergent strand
NASA Technical Reports Server (NTRS)
Simon, W. E.; Witte, L. C.; Hedgcoxe, P. G.
1974-01-01
A mathematical model was developed to describe the heat transfer characteristics of a hot strand emerging into a surrounding coolant. A stable strand of constant efflux velocity is analyzed, with a constant (average) heat transfer coefficient on the sides and leading surface of the strand. After developing a suitable governing equation to provide an adequate description of the physical system, the dimensionless governing equation is solved with Laplace transform methods. The solution yields the temperature within the strand as a function of axial distance and time. Generalized results for a wide range of parameters are presented, and the relationship of the results and experimental observations is discussed.
Evaporative heat transfer in beds of sensible heat pellets
Arimilli, R.V.; Moy, C.A.
1989-03-01
An experimental study of boiling/evaporative heat transfer from heated spheres in vertical packed beds with downward liquid-vapor flow of Refrigerant-113 was conducted. Surface superheats of 1 to 50{degrees}C, mass flow rates of 1.7 to 5.6 Kg/min, sphere diameters of 1.59 and 2.54 cm, quality (i.e., mass fraction of vapor) of the inlet flow of 0.02 to 1.0, and two surface conditions were considered. Instrumented smooth and rough aluminum spheres were used to measure the heat transfer coefficients under steady state conditions. Heat transfer coefficients were independently determined for each sphere at three values three values of surface superheat. The quantitative results of this extensive experimental study are successfully correlated. The correlation equation for the boiling heat transfer coefficients is presented in terms of a homogeneous model. The correlation may be used in the development of numerical models to simulate the transient thermal performance of packed bed thermal energy storage unit while operating as an evaporator. The boiling of the liquid-vapor flow around the spheres in the packed bed was visually observed with a fiber-optic baroscope and recorded on a videotape. The visualization results showed qualitatively the presence of four distinct flow regimes. One of these occurs under saturated inlet conditions and are referred to as the Low-quality, Medium-quality, and High-quality Regimes. The regimes are discussed in detail in this paper.
Heat transfer mechanisms in pulsating heat-pipes with nanofluid
NASA Astrophysics Data System (ADS)
Gonzalez, Miguel; Kelly, Brian; Hayashi, Yoshikazu; Kim, Yoon Jo
2015-01-01
In this study, the effect of silver nanofluid on a pulsating heat-pipe (PHP) thermal performance was experimentally investigated to figure out how nanofluid works with PHP. A closed loop PHP was built with 3 mm diameter tubes. Thermocouples and pressure transducers were installed for fluid and surface temperature and pressure measurements. The operating temperature of the PHP varied from 30-100 °C, with power rates of 61 W and 119 W. The fill ratio of 30%, 50%, and 70% were tested. The results showed that the evaporator heat transfer performance was degraded by the addition of nanoparticles due to increased viscosity at high power rate, while the positive effects of high thermal conductivity and enhanced nucleate boiling worked better at low power rate. In the condenser section, owing to the relatively high liquid content, nanofluid more effectively improved the heat transfer performance. However, since the PHP performance was dominantly affected by evaporator heat transfer performance, the overall benefit of enhanced condenser section performance was greatly limited. It was also observed that the poor heat transfer performance with nanofluid at the evaporator section led to lower operating pressure of PHP.
Experimental determination of stator endwall heat transfer
NASA Technical Reports Server (NTRS)
Boyle, Robert J.; Russell, Louis M.
1989-01-01
Local Stanton numbers were experimentally determined for the endwall surface of a turbine vane passage. A six vane linear cascade having vanes with an axial chord of 13.81 cm was used. Results were obtained for Reynolds numbers based on inlet velocity and axial chord between 73,000 and 495,000. The test section was connected to a low pressure exhaust system. Ambient air was drawn into the test section, inlet velocity was controlled up to a maximum of 59.4 m/sec. The effect of the inlet boundary layer thickness on the endwall heat transfer was determined for a range of test section flow rates. The liquid crystal measurement technique was used to measure heat transfer. Endwall heat transfer was determined by applying electrical power to a foil heater attached to the cascade endwall. The temperature at which the liquid crystal exhibited a specific color was known from a calibration test. Lines showing this specific color were isotherms, and because of uniform heat generation they were also lines of nearly constant heat transfer. Endwall static pressures were measured, along with surveys of total pressure and flow angles at the inlet and exit of the cascade.
Experimental determination of stator endwall heat transfer
NASA Technical Reports Server (NTRS)
Boyle, Robert J.; Russell, Louis M.
1989-01-01
Local Stanton numbers were experimentally determined for the endwall surface of a turbine vane possage. A six vane linear cascade having vanes with an axial chord of 13.81 cm was used. Resutls were obtained for Reynolds numbers based on inlet velocity and axial chord between 75,000 and 495,000. The test section was connected to a low pressure exhaust system. Ambient air was drawn into the test section, inlet velocity was controlled up to a maximum of 59.4 m/sec. The effect of the inlet boundary layer thickness on the endwall heat transfer was determined for a range of test section flow rates. The liquid crystal measurement technique was used to measure heat transfer. Endwall heat transfer was determined by applying electrical power to a foil heater attached to the cascade endwall. The temperature at which the liquid crystal exhibited a specific color was known from a calibration test. Lines showing this specific color were isotherms, and because of uniform heat generation they were also lines of nearly constant heat transfer. Endwall static pressures were measured, along with surveys of total pressure and flow angles at the inlet and exit of the cascade.
Natural convective heat transfer from square cylinder
NASA Astrophysics Data System (ADS)
Novomestský, Marcel; Smatanová, Helena; Kapjor, Andrej
2016-06-01
This article is concerned with natural convective heat transfer from square cylinder mounted on a plane adiabatic base, the cylinders having an exposed cylinder surface according to different horizontal angle. The cylinder receives heat from a radiating heater which results in a buoyant flow. There are many industrial applications, including refrigeration, ventilation and the cooling of electrical components, for which the present study may be applicable
Experimental Investigations of Heat and Mass Transfer in Microchannel Heat-Transfer Elements
NASA Astrophysics Data System (ADS)
Konovalov, D. A.
2016-06-01
The present work seeks to develop and investigate experimentally microchannel heat-exchange apparatuses of two designs: with porous elements manufactured from titanium and copper, and also based on the matrix of filamentary silicon single crystals under operating conditions with high heat loads, unsteadiness, and nonlinear flow of the coolant. For experimental investigations, the authors have developed and manufactured a unique test bench allowing tests of the developed heat-transfer elements in unsteady operating regimes. The performed experimental investigations have made it possible to obtain criterial dependences of the heat-transfer coefficient on the Reynolds and Prandtl numbers and to refine the values of viscous and inertial coefficients. It has been established that microchannel heat-transfer elements based on silicon single crystals, which make it possible to remove a heat flux above 100 W/cm2, are the most efficient. For porous heat-transfer elements, the best result was attained for wedge-shaped copper samples. According to investigation results, the authors have considered the issues of optimization of thermal and hydraulic characteristics of the heat-transfer elements under study. In the work, the authors have given examples of practical use of the developed heat-transfer elements for cooling systems of radioelectronic equipment.
Experimental Investigations of Heat and Mass Transfer in Microchannel Heat-Transfer Elements
NASA Astrophysics Data System (ADS)
Konovalov, D. A.
2016-05-01
The present work seeks to develop and investigate experimentally microchannel heat-exchange apparatuses of two designs: with porous elements manufactured from titanium and copper, and also based on the matrix of filamentary silicon single crystals under operating conditions with high heat loads, unsteadiness, and nonlinear flow of the coolant. For experimental investigations, the authors have developed and manufactured a unique test bench allowing tests of the developed heat-transfer elements in unsteady operating regimes. The performed experimental investigations have made it possible to obtain criterial dependences of the heat-transfer coefficient on the Reynolds and Prandtl numbers and to refine the values of viscous and inertial coefficients. It has been established that microchannel heat-transfer elements based on silicon single crystals, which make it possible to remove a heat flux above 100 W/cm2, are the most efficient. For porous heat-transfer elements, the best result was attained for wedge-shaped copper samples. According to investigation results, the authors have considered the issues of optimization of thermal and hydraulic characteristics of the heat-transfer elements under study. In the work, the authors have given examples of practical use of the developed heat-transfer elements for cooling systems of radioelectronic equipment.
Heat flux sensors for infrared thermography in convective heat transfer.
Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso
2014-01-01
This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described. PMID:25386758
Heat Flux Sensors for Infrared Thermography in Convective Heat Transfer
Carlomagno, Giovanni Maria; de Luca, Luigi; Cardone, Gennaro; Astarita, Tommaso
2014-01-01
This paper reviews the most dependable heat flux sensors, which can be used with InfraRed (IR) thermography to measure convective heat transfer coefficient distributions, and some of their applications performed by the authors' research group at the University of Naples Federico II. After recalling the basic principles that make IR thermography work, the various heat flux sensors to be used with it are presented and discussed, describing their capability to investigate complex thermo-fluid-dynamic flows. Several applications to streams, which range from natural convection to hypersonic flows, are also described. PMID:25386758
Computational Aspects of Heat Transfer in Structures
NASA Technical Reports Server (NTRS)
Adelman, H. M. (Compiler)
1982-01-01
Techniques for the computation of heat transfer and associated phenomena in complex structures are examined with an emphasis on reentry flight vehicle structures. Analysis methods, computer programs, thermal analysis of large space structures and high speed vehicles, and the impact of computer systems are addressed.
Turbulent Heat Transfer in Ribbed Pipe Flow
NASA Astrophysics Data System (ADS)
Kang, Changwoo; Yang, Kyung-Soo
2012-11-01
From the view point of heat transfer control, surface roughness is one of the popular ways adopted for enhancing heat transfer in turbulent pipe flow. Such a surface roughness is often modeled with a rib. In the current investigation, Large Eddy Simulation has been performed for turbulent flow in a pipe with periodically-mounted ribs at Reτ=700, Pr=0.71, and p / k =2, 4, and 8. Here, p and k represent the pitch and rib height, respectively. The rib height is fixed as one tenth of the pipe radius. The profiles of mean velocity components, mean temperature, root-mean-squares (rms) of temperature fluctuation are presented at the selected streamwise locations. In comparison with the smooth-pipe case at the same Re and Pr, the effects of the ribs are clearly identified, leading to overall enhancement of turbulent heat transfer in terms of Nu. The budget of temperature variance is presented in the form of contours. The results of an Octant analysis are also given to elucidate the dominant events. Our LES results shed light on a complete understanding of the heat-transfer mechanisms in turbulent ribbed-pipe flow which has numerous applications in engineering. This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MEST) (No. 2012013019).
Heat transfer in magma in situ
Dunn, J.C.; Carrigan, C.R.; Wemple, R.P.
1983-12-16
Heat transfer rates in a basaltic magma were measured under typical magma chamber conditions and a numerical model of the experiment was used to estimate magma viscosity. The results are of value for assessing methods of thermal energy extraction from magma bodies in the upper crust as well as for modeling the evolutionary track of these systems. 13 references, 3 figures.
FED. Zoning for TRUMP Heat Transfer Code
Elrod, D.
1987-10-23
FED reduces the effort required to obtain the necessary geometric input for problems which are to be solved using the heat-transfer code, TRUMP. TRUMP calculates transient and steady-state temperature distributions in multidimensional systems. FED can properly zone any body of revolution in one, two, or three dimensions.
Heat transfer in rotating coolant channels
NASA Astrophysics Data System (ADS)
Wang, Baoguan; Zheng, Jirui; Ding, Xiaojiang
The effect of cooling channels' rotation on the local and mean heat transfer is investigated using an experimental simulation of three types of flow in rotating circular tubes: (1) flow parallel to the rotating axis, (2) radially outward flow perpendicular to the rotating axis, and (3) radially inward flow perpendicular to the rotating axis. Theoretical analysis uses the boundary layer model method, in which the flow in a tube is divided into the core and boundary layer zones with different assumptions for each zone, and the equations are solved using the momentum integration method. Experimental results were obtained using a specially designed facility incorporating all three modes of flow. The results confirm that rotation of the flow in a tube can enhance the heat transfer processes whether the flow is parallel or perpendicular to the rotating axis. The incremental increase in heat transfer rate due to rotation was found to be more pronounced at low rotational speeds than at high speeds. The variation of local heat transfer coefficients along axial direction is affected by the inlet and outlet sections and by the ratio of length to diameter.
Heat Transfer and Thermodynamics: a Compilation
NASA Technical Reports Server (NTRS)
1974-01-01
A compilation is presented for the dissemination of information on technological developments which have potential utility outside the aerospace and nuclear communities. Studies include theories and mechanical considerations in the transfer of heat and the thermodynamic properties of matter and the causes and effects of certain interactions.
Forced Convection Heat Transfer in Circular Pipes
ERIC Educational Resources Information Center
Tosun, Ismail
2007-01-01
One of the pitfalls of engineering education is to lose the physical insight of the problem while tackling the mathematical part. Forced convection heat transfer (the Graetz-Nusselt problem) certainly falls into this category. The equation of energy together with the equation of motion leads to a partial differential equation subject to various…
Information highway and numerical heat transfer
Shih, T.M.; Minkowycz, W.J.
1996-11-22
It is proposed that researchers in the numerical heat transfer community need to realize the trend of the information highway and agree to use a protocol or a module that constitutes the core of a computer program solving heat transfer problems. This will avoid duplicate programming and accelerate the technology advancement of numerical heat transfer. The module for two-dimensional incompressible Navier-Stokes flows is presented and explained. It is further demonstrated that, using this module as the foundation, the user can straightforwardly build up an entire personal computer code by inputting the data, specifying boundary conditions, and outputting the result. Other modules for slightly more complicated problems, such as transient flows with variable viscosity in irregular geometries, are also presented. Other than zoning matches for problems with multizones, the programming task for a user becomes minimal and simple: input, prescribe the boundary conditions, and output. The availability of Navier-Stokes modules is particularly helpful for less experienced numerical researchers, newcomers, and graduate students who have just entered the area of heat transfer and fluid flows.
Heat transfer in a nuclear rocket engine
Konyukhov, G.V.; Petrov, A.I.
1995-02-01
Special features of heat transfer in the reactor of a nuclear rocket engine (NRE) are dealt with. It is shown that the design of the cooling system of the NRE reactor is governed by its stability to small deviations of the parameters from the corresponding calculated values and the possibility of compensating for effects due to nonuniformities and distrubances of various types and scales.
Cooperative heat transfer and ground coupled storage system
Metz, P.D.
A cooperative heat transfer and ground coupled storage system wherein collected solar heat energy is ground stored and permitted to radiate into the adjacent ground for storage therein over an extended period of time when such heat energy is seasonally maximally available. Thereafter, when said heat energy is seasonally minimally available and has propagated through the adjacent ground a substantial distance, the stored heat energy may be retrieved by a circumferentially arranged heat transfer means having a high rate of heat transfer.
Cooperative heat transfer and ground coupled storage system
Metz, Philip D.
1982-01-01
A cooperative heat transfer and ground coupled storage system wherein collected solar heat energy is ground stored and permitted to radiate into the adjacent ground for storage therein over an extended period of time when such heat energy is seasonally maximally available. Thereafter, when said heat energy is seasonally minimally available and has propagated through the adjacent ground a substantial distance, the stored heat energy may be retrieved by a circumferentially arranged heat transfer means having a high rate of heat transfer.
Numerical Analysis of Heat Transfer During Quenching Process
NASA Astrophysics Data System (ADS)
Madireddi, Sowjanya; Krishnan, Krishnan Nambudiripad; Reddy, Ammana Satyanarayana
2016-06-01
A numerical model is developed to simulate the immersion quenching process of metals. The time of quench plays an important role if the process involves a defined step quenching schedule to obtain the desired characteristics. Lumped heat capacity analysis used for this purpose requires the value of heat transfer coefficient, whose evaluation requires large experimental data. Experimentation on a sample work piece may not represent the actual component which may vary in dimension. A Fluid-Structure interaction technique with a coupled interface between the solid (metal) and liquid (quenchant) is used for the simulations. Initial times of quenching shows boiling heat transfer phenomenon with high values of heat transfer coefficients (5000-2.5 × 105 W/m2K). Shape of the work piece with equal dimension shows less influence on the cooling rate Non-uniformity in hardness at the sharp corners can be reduced by rounding off the edges. For a square piece of 20 mm thickness, with 3 mm fillet radius, this difference is reduced by 73 %. The model can be used for any metal-quenchant combination to obtain time-temperature data without the necessity of experimentation.
Evaporative Heat Transfer Mechanisms within a Heat Melt Compactor
NASA Technical Reports Server (NTRS)
Golliher, Eric L.; Gotti, Daniel J.; Rymut, Joseph Edward; Nguyen, Brian K; Owens, Jay C.; Pace, Gregory S.; Fisher, John W.; Hong, Andrew E.
2013-01-01
This paper will discuss the status of microgravity analysis and testing for the development of a Heat Melt Compactor (HMC). Since fluids behave completely differently in microgravity, the evaporation process for the HMC is expected to be different than in 1-g. A thermal model is developed to support the design and operation of the HMC. Also, low-gravity aircraft flight data is described to assess the point at which water may be squeezed out of the HMC during microgravity operation. For optimum heat transfer operation of the HMC, the compaction process should stop prior to any water exiting the HMC, but nevertheless seek to compact as much as possible to cause high heat transfer and therefore shorter evaporation times.
BWR Core Heat Transfer Code System.
1999-04-27
Version 00 MOXY is used for the thermal analysis of a planar section of a boiling water reactor (BWR) fuel element during a loss-of-coolant accident (LOCA). The code emplyoys models that describe heat transfer by conduction, convection, and thermal radiation, and heat generation by metal-water reaction and fission product decay. Models are included for considering fuel-rod swelling and rupture, energy transport across the fuel-to-cladding gap, and the thermal response of the canister. MOXY requires thatmore » time-dependent data during the blowdown process for the power normalized to the steady-state power, for the heat-transfer coefficient, and for the fluid temperature be provided as input. Internal models provide these parameters during the heatup and emergency cooling phases.« less
Advanced Heat Transfer and Thermal Storage Fluids
Moens, L.; Blake, D.
2005-01-01
The design of the next generation solar parabolic trough systems for power production will require the development of new thermal energy storage options with improved economics or operational characteristics. Current heat-transfer fluids such as VP-1?, which consists of a eutectic mixture of biphenyl and diphenyl oxide, allow a maximum operating temperature of ca. 300 C, a limit above which the vapor pressure would become too high and would require pressure-rated tanks. The use of VP-1? also suffers from a freezing point around 13 C that requires heating during cold periods. One of the goals for future trough systems is the use of heat-transfer fluids that can act as thermal storage media and that allow operating temperatures around 425 C combined with lower limits around 0 C. This paper presents an outline of our latest approach toward the development of such thermal storage fluids.
Numerical Modeling of Ablation Heat Transfer
NASA Technical Reports Server (NTRS)
Ewing, Mark E.; Laker, Travis S.; Walker, David T.
2013-01-01
A unique numerical method has been developed for solving one-dimensional ablation heat transfer problems. This paper provides a comprehensive description of the method, along with detailed derivations of the governing equations. This methodology supports solutions for traditional ablation modeling including such effects as heat transfer, material decomposition, pyrolysis gas permeation and heat exchange, and thermochemical surface erosion. The numerical scheme utilizes a control-volume approach with a variable grid to account for surface movement. This method directly supports implementation of nontraditional models such as material swelling and mechanical erosion, extending capabilities for modeling complex ablation phenomena. Verifications of the numerical implementation are provided using analytical solutions, code comparisons, and the method of manufactured solutions. These verifications are used to demonstrate solution accuracy and proper error convergence rates. A simple demonstration of a mechanical erosion (spallation) model is also provided to illustrate the unique capabilities of the method.
Heat transfer in bioengineering and medicine
Chato, J.C.; Diller, T.E.; Diller, K.R.; Roemer, R.B.
1987-01-01
This book contains the following papers: New ideas in heat transfer for agricultural animals; Issues in heat transfer and tumor blood flow in localized hyperthermia treatments of cancer; Ultrasound enhances adriamycin toxicity in vitro; Scanned, focused ultrasound hyperthermia treatment of brain tumors; Mathematical prediction and phantom studies of the clinical target ''hot spot'' using a three applicator phased array system (TRIPAS); Development of an endoscopic RF hyperthermia system for deep tumor therapy; Simultaneous measurement of intrinsic and effective thermal conductivity; Determination of the transport of thermal energy by conduction in perfused tissue; A whole body thermal model of man with a realistic circulatory system; and Canine muscle blood flow changes in response to initial heating rates.
Nonlinear Heat Transfer 2d Structure
1987-09-01
DOT-BPMD is a general-purpose, finite-element, heat-transfer program used to predict thermal environments. The code considers linear and nonlinear transient or steady-state heat conduction in two-dimensional planar or axisymmetric representations of structures. Capabilities are provided for modeling anisotropic heterogeneous materials with temperature-dependent thermal properties and time-dependent temperature, heat flux, convection and radiation boundary conditions, together with time-dependent internal heat generation. DOT-BPMD may be used in the evaluation of steady-state geothermal gradients as well as in themore » transient heat conduction analysis of repository and waste package subsystems. Strengths of DOT-BPMD include its ability to account for a wide range of possible boundary conditions, nonlinear material properties, and its efficient equation solution algorithm. Limitations include the lack of a three-dimensional analysis capability, no radiative or convective internal heat transfer, and the need to maintain a constant time-step in each program execution.« less
Heat transfer in GTA welding arcs
NASA Astrophysics Data System (ADS)
Huft, Nathan J.
Heat transfer characteristics of Gas Tungsten Arc Welding (GTAW) arcs with arc currents of 50 to 125 A and arc lengths of 3 to 11 mm were measured experimentally through wet calorimetry. The data collected were used to calculate how much heat reported to the cathode and anode and how much was lost from the arc column. A Visual Basic for Applications (VBA) macro was written to further analyze the data and account for Joule heating within the electrodes and radiation and convection losses from the arc, providing a detailed account of how heat was generated and dissipated within the system. These values were then used to calculate arc efficiencies, arc column voltages, and anode and cathode fall voltages. Trends were noted for variances in the arc column voltage, power dissipated from the arc column, and the total power dissipated by the system with changing arc length. Trends for variances in the anode and cathode fall voltages, total power dissipated, Joule heating within the torches and electrodes with changing arc current were also noted. In addition, the power distribution between the anode and cathode for each combination of arc length and arc current was examined. Keywords: Gas Tungsten Arc Welding, GTAW, anode fall, cathode fall, heat transfer, wet calorimetry
Comparison of actual and predicted energy savings in Minnesota gas-heated single-family homes
Hirst, E.; Goeltz, R.
1984-03-01
Data available from a recent evaluation of a home energy audit program in Minnesota are sufficient to allow analysis of the actual energy savings achieved in audited homes and of the relationship between actual and predicted savings. The program, operated by Northern States Power in much of the southern half of the state, is part of Minnesota's version of the federal Residential Conservation Service. NSP conducted almost 12 thousand RCS audits between April 1981 (when the progam began) and the end of 1982. The data analyzed here, available for 346 homes that obtained an NSP energy audit, include monthly natural gas bills from October 1980 through April 1983; heating degree day data matched to the gas bills; energy audit reports; and information on household demographics, structure characteristics, and recent conservation actions from mail and telephone surveys. The actual reduction in weather-adjusted natural gas use between years 1 and 3 averaged 19 MBtu across these homes (11% of preprogram consumption); the median value of the saving was 16 MBtu/year. The variation in actual saving is quite large: gas consumption increased in almost 20% of the homes, while gas consumption decreased by more than 50 MBtu/year in more than 10% of the homes. These households reported an average expenditure of almost $1600 for the retrofit measures installed in their homes; the variation in retrofit cost, while large, was not as great as the variation in actual natural gas savings.
NASA Astrophysics Data System (ADS)
Grabenstein, V.; Kabelac, S.
2012-11-01
Plate heat exchanger (PHE) are today widely used in industrial heat transfer applications due to their good thermal performance, modest space requirement, easy accessibility to all areas and their lower capital and operating costs as compared to shell-and-tube heat exchangers. Although authoritative models for the design of PHE used as condensers are missing, the number of applications where a PHE is operating as a condenser increases. On the way to a reliable model based on physical approaches for the prediction of heat transfer and pressure drop during the condensation process inside a PHE, the flow and heat interactions as well as their dependence on the geometrical parameters of the corrugated plates and the operating conditions must be studied in detail. In this work the stepwise procedure for the fundamental construction of such a model is described. An experimental setup was built to analyze the characteristics of the two-phase-flow in PHE. A single gap, consisting of two transparent corrugated plates, was tested with a two-phase flow of air/water and also with boiling refrigerant R365mfc. Flow pattern maps were constructed for plates with corrugation angles of 27 and 63 degrees relative to the direction of flow. Investigations of the local heat transfer coefficients and the pressure drop were done with the same plates. The measurement of the local heat transfer coefficients was carried out by the use of the "Temperature Oscillation InfraRed Thermography" (TOIRT) method. Based on these results three main flow patterns are defined: film flow, bubbly flow and slug flow. For each of the three flow patterns an own model for the heat transfer and pressure drop mechanism are developed and the heat transfer coefficient and the friction factor is calculated with different equations depending on the actual steam quality, mass flow and geometrical parameters by means of a flow pattern map. The theory of the flow pattern based prediction models is proved with own
Analysis of a heat transfer device for measuring film coefficients
NASA Technical Reports Server (NTRS)
Medrow, R. A.; Johnson, R. L.; Loomis, W. R.; Wedeven, L. D.
1975-01-01
A heat transfer device consisting of a heated rotating cylinder in a bath was analyzed for its effectiveness to determine heat transfer coefficient of fluids. A time dependent analysis shows that the performance is insensitive to the value of heat transfer coefficient with the given rig configuration.
Transient Heat Transfer in TCAP Coils
Steimke, J.L.
1999-03-09
The Thermal Cycling Absorption Process (TCAP) is used to separate isotopes of hydrogen. TCAP involves passing a stream of mixed hydrogen isotopes through palladium deposited on kieselguhr (Pd/k) while cycling the temperature of the Pd/k. Kieselguhr is a silica mineral also called diatomite. To aid in the design of a full scale facility, the Thermal Fluids Laboratory was used by the Chemical and Hydrogen Technology Section to compare the heat transfer properties of three different configurations of stainless steel coils containing kieselguhr and helium. Testing of coils containing Pd/k and hydrogen isotopes would have been more prototypical but would have been too expensive. Three stainless steel coils filled with kieselguhr were tested; one made from 2.0 inch diameter tubing, one made from 2.0 inch diameter tubing with foam copper embedded in the kieselguhr and one made from 1.25 inch diameter tubing. It was known prior to testing that increasing the tubing diameter from 1.25 inch to 2.0 inch would slow the rate of temperature change. The primary purpose of the testing was to measure to what extent the presence of copper foam in a 2.0" tubing coil would compensate for the effect of larger diameter. Each coil was connected to a pressure gage and the coil was evacuated and backfilled with helium gas. Helium was used instead of a mixture of hydrogen isotopes for reasons of safety. Each coil was quickly immersed in a stirred bath of ethylene glycol at a temperature of approximately 100 degrees Celsius. The coil pressure increased, reflecting the increase in average temperature of its contents. The pressure transient was recored as a function of time after immersion. Because of the actual process will use Pd/k instead of kieselguhr, additional tests were run to determine the differences in thermal properties between the two materials. The method was to position a thermocouple at the center of a hollow sphere and pack the sphere with Pd/k. The sphere was sealed, quickly
Transient Heat Transfer in TCAP Coils
Steimke, J.L.
1999-03-09
The Thermal Cycling Absorption Process (TCAP) is used to separate isotopes of hydrogen. TCAP involves passing a stream of mixed hydrogen isotopes through palladium deposited on kieselguhr (Pd/k) while cycling the temperature of the Pd/k. Kieselguhr is a silica mineral also called diatomite. To aid in the design of a full scale facility, the Thermal Fluids Laboratory was used by the Chemical and Hydrogen Technology Section to compare the heat transfer properties of three different configurations of stainless steel coils containing kieselguhr and helium. Testing of coils containing Pd/k and hydrogen isotopes would have been more prototypical but would have been too expensive. Three stainless steel coils filled with kieselguhr were tested; one made from 2.0 inch diameter tubing, one made from 2.0 inch diameter tubing with foam copper embedded in the kieselguhr and one made from 1.25 inch diameter tubing. It was known prior to testing that increasing the tubing diameter from 1.25 inch to 2.0 inch would slow the rate of temperature change. The primary purpose of the testing was to measure to what extent the presence of copper foam in a 2.0 tubing coil would compensate for the effect of larger diameter. Each coil was connected to a pressure gage and the coil was evacuated and backfilled with helium gas. Helium was used instead of a mixture of hydrogen isotopes for reasons of safety. Each coil was quickly immersed in a stirred bath of ethylene glycol at a temperature of approximately 100 degrees Celsius. The coil pressure increased, reflecting the increase in average temperature of its contents. The pressure transient was recored as a function of time after immersion. Because of the actual process will use Pd/k instead of kieselguhr, additional tests were run to determine the differences in thermal properties between the two materials. The method was to position a thermocouple at the center of a hollow sphere and pack the sphere with Pd/k. The sphere was sealed, quickly
Heterogeneous nanofluids: natural convection heat transfer enhancement
2011-01-01
Convective heat transfer using different nanofluid types is investigated. The domain is differentially heated and nanofluids are treated as heterogeneous mixtures with weak solutal diffusivity and possible Soret separation. Owing to the pronounced Soret effect of these materials in combination with a considerable solutal expansion, the resulting solutal buoyancy forces could be significant and interact with the initial thermal convection. A modified formulation taking into account the thermal conductivity, viscosity versus nanofluids type and concentration and the spatial heterogeneous concentration induced by the Soret effect is presented. The obtained results, by solving numerically the full governing equations, are found to be in good agreement with the developed solution based on the scale analysis approach. The resulting convective flows are found to be dependent on the local particle concentration φ and the corresponding solutal to thermal buoyancy ratio N. The induced nanofluid heterogeneity showed a significant heat transfer modification. The heat transfer in natural convection increases with nanoparticle concentration but remains less than the enhancement previously underlined in forced convection case. PMID:21711755
Heterogeneous nanofluids: natural convection heat transfer enhancement.
Oueslati, Fakhreddine Segni; Bennacer, Rachid
2011-01-01
Convective heat transfer using different nanofluid types is investigated. The domain is differentially heated and nanofluids are treated as heterogeneous mixtures with weak solutal diffusivity and possible Soret separation. Owing to the pronounced Soret effect of these materials in combination with a considerable solutal expansion, the resulting solutal buoyancy forces could be significant and interact with the initial thermal convection. A modified formulation taking into account the thermal conductivity, viscosity versus nanofluids type and concentration and the spatial heterogeneous concentration induced by the Soret effect is presented. The obtained results, by solving numerically the full governing equations, are found to be in good agreement with the developed solution based on the scale analysis approach. The resulting convective flows are found to be dependent on the local particle concentration φ and the corresponding solutal to thermal buoyancy ratio N. The induced nanofluid heterogeneity showed a significant heat transfer modification. The heat transfer in natural convection increases with nanoparticle concentration but remains less than the enhancement previously underlined in forced convection case. PMID:21711755
Heterogeneous nanofluids: natural convection heat transfer enhancement
NASA Astrophysics Data System (ADS)
Oueslati, Fakhreddine Segni; Bennacer, Rachid
2011-12-01
Convective heat transfer using different nanofluid types is investigated. The domain is differentially heated and nanofluids are treated as heterogeneous mixtures with weak solutal diffusivity and possible Soret separation. Owing to the pronounced Soret effect of these materials in combination with a considerable solutal expansion, the resulting solutal buoyancy forces could be significant and interact with the initial thermal convection. A modified formulation taking into account the thermal conductivity, viscosity versus nanofluids type and concentration and the spatial heterogeneous concentration induced by the Soret effect is presented. The obtained results, by solving numerically the full governing equations, are found to be in good agreement with the developed solution based on the scale analysis approach. The resulting convective flows are found to be dependent on the local particle concentration φ and the corresponding solutal to thermal buoyancy ratio N. The induced nanofluid heterogeneity showed a significant heat transfer modification. The heat transfer in natural convection increases with nanoparticle concentration but remains less than the enhancement previously underlined in forced convection case.
Unsteady heat transfer during subcooled film boiling
NASA Astrophysics Data System (ADS)
Yagov, V. V.; Zabirov, A. R.; Lexin, M. A.
2015-11-01
Cooling of high-temperature bodies in subcooled liquid is of importance for quenching technologies and also for understanding the processes initiating vapor explosion. An analysis of the available experimental information shows that the mechanisms governing heat transfer in these processes are interpreted ambiguously; a more clear-cut definition of the Leidenfrost temperature notion is required. The results of experimental observations (Hewitt, Kenning, and previous investigations performed by the authors of this article) allow us to draw a conclusion that there exists a special mode of intense heat transfer during film boil- ing of highly subcooled liquid. For revealing regularities and mechanisms governing intense transfer of energy in this process, specialists of Moscow Power Engineering Institute's (MPEI) Department of Engineering Thermal Physics conduct systematic works aimed at investigating the cooling of high-temperature balls made of different metals in water with a temperature ranging from 20 to 100°C. It has been determined that the field of temperatures that takes place in balls with a diameter of more than 30 mm in intense cooling modes loses its spherical symmetry. An approximate procedure for solving the inverse thermal conductivity problem for calculating the heat flux density on the ball surface is developed. During film boiling, in which the ball surface temperature is well above the critical level for water, and in which liquid cannot come in direct contact with the wall, the calculated heat fluxes reach 3-7 MW/m2.
Acquisition systems for heat transfer measurement
De Witt, R.J.
1983-01-01
Practical heat transfer data acquisition systems are normally characterized by the need for high-resolution, low-drift, low-speed recording devices. Analog devices such as strip chart or circular recorders and FM analog magnetic tape have excellent resolution and work well when data will be presented in temperature versus time format only and need not be processed further. Digital systems are more complex and require an understanding of the following components: digitizing devices, interface bus types, processor requirements, and software design. This paper discusses all the above components of analog and digital data acquisition, as they are used in current practice. Additional information on thermocouple system analysis will aid the user in developing accurate heat transfer measuring systems.
Modeling heat transfer within porous multiconstituent materials
NASA Astrophysics Data System (ADS)
Niezgoda, Mathieu; Rochais, Denis; Enguehard, Franck; Rousseau, Benoit; Echegut, Patrick
2012-06-01
The purpose of our work has been to determine the effective thermal properties of materials considered heterogeneous at the microscale but which are regarded as homogenous in the macroscale environment in which they are used. We have developed a calculation code that renders it possible to simulate thermal experiments over complex multiconstituent materials from their numerical microstructural morphology obtained by volume segmentation through tomography. This modeling relies on the transient solving of the coupled conductive and radiative heat transfer in these voxelized structures.
Heat and mass transfer in materials processing
Tanasawa, I. . Inst. of Industrial Science); Lior, N. . Dept. of Mechanical Engineering and Applied Mechanics)
1992-01-01
This book contains forty papers presented at the seminar. The papers are representative of the seminar's scope, and include plasma spraying, laser and electron beam processing, crystal growth, solidification, steel processing, casting and molding, and papermaking, as well as fundamental heat transfer issues and physical properties underlying all of the above. The seminar emphasized thorough discussion of the presentations and of the subfields. Brief summaries of the discussions are presented in the rapporteurs' reports.
Radiation heat transfer shapefactors for combustion systems
NASA Technical Reports Server (NTRS)
Emery, A. F.; Johansson, O.; Abrous, A.
1987-01-01
The computation of radiation heat transfer through absorbing media is commonly done through the zoning method which relies upon values of the geometric mean transmittance and absorptance. The computation of these values is difficult and expensive, particularly if many spectral bands are used. This paper describes the extension of a scan line algorithm, based upon surface-surface radiation, to the computation of surface-gas and gas-gas radiation transmittances.
Heat Transfer in a Superelliptic Transition Duct
NASA Technical Reports Server (NTRS)
Poinsatte, Philip; Thurman, Douglas; Hippensteele, Steven
2008-01-01
Local heat transfer measurements were experimentally mapped using a transient liquid-crystal heat transfer technique on the surface of a circular-to-rectangular transition duct. The transition duct had a length-to-diameter ratio of 1.5 and an exit-plane aspect ratio of 3. The crosssectional geometry was defined by the equation of a superellipse. The cross-sectional area was the same at the inlet and exit but varied up to 15 percent higher through the transition. The duct was preheated to a uniform temperature (nominally 64 C) before allowing room temperature air to be suddenly drawn through it. As the surface cooled, the resulting isothermal contours on the duct surface were revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record was made of the surface temperature and time data for all points on the duct surfaces during each test. Using this surface temperature-time data together with the temperature of the air flowing through the model and the initial temperature of the model wall, the heat transfer coefficient was calculated by employing the classic one-dimensional, semi-infinite wall heat transfer conduction model. Test results are reported for inlet diameter-based Reynolds numbers ranging from 0.4x106 to 2.4x106 and two grid-generated freestream turbulence intensities of about 1 percent, which is typical of wind tunnels, and up to 16 percent, which may be more typical of real engine conditions.
Coolant passage heat transfer with rotation
NASA Astrophysics Data System (ADS)
Hajek, T. J.; Higgins, A. W.
1985-10-01
The objective is to develop a heat transfer and pressure drop data base, computational fluid dynamic techniques, and correlations for multi-pass rotating coolant passages with and without flow turbulators. The experimental effort is focused on the simulation of configurations and conditions expected in the blades of advanced aircraft high pressure turbines. With the use of this data base, the effects of Coriolis and buoyancy forces on the coolant side flow can be included in the design of turbine blades.
Low-melting point heat transfer fluid
Cordaro, Joseph Gabriel; Bradshaw, Robert W.
2010-11-09
A low-melting point, heat transfer fluid made of a mixture of five inorganic salts including about 29.1-33.5 mol % LiNO.sub.3, 0-3.9 mol % NaNO.sub.3, 2.4-8.2 mol % KNO.sub.3, 18.6-19.9 mol % NaNO.sub.2, and 40-45.6 mol % KNO.sub.2. These compositions can have liquidus temperatures below 80.degree. C. for some compositions.
Combustion and heat transfer in porous media
Sathe, S.B.; Peck, R.E.; Tong, T.W.
1990-06-01
The objective of the present study is to generate fundamental knowledge about heat transfer and combustion in porous radiant burners (PRBs) in order to improve their performance. A theoretical heat transfer and combustion model is developed to study the characteristics of PRBs. The model accounts for non-local thermal equilibrium between the solid and gas phases. The solid is assumed to absorb, emit and scatter radiant energy. Combustion is modeled as a one-step global reaction. It is revealed that the flame speed inside the porous medium is enhanced compared to the adiabatic flame speeds due to the higher conductivity of the solid compared to the gas as well as due to radiative preheating of the reactants. The effects of the properties of the porous material on the flame speeds, radiative outputs and efficiencies were investigated. To improve the radiative output from the burner, it is desirable that the porous layer has an optical thickness of about ten. The radiative output and the efficiency is higher for lower scattering albedo. The heat transfer coupling between the solid and gas phases should be high enough to ensure local thermal equilibrium, by choosing a fine porous matrix. Higher solid phase conduction enhances the flame speed and the radiative output. Experiments are performed on a ceramic foam to verify the theoretical findings. The existence of the two stability regions was verified experimentally.
Parallel and vector computation in heat transfer
Georgiadis, J.G. ); Murthy, J.Y. )
1990-01-01
This collection of manuscripts complements a number of other volumes related to engineering numerical analysis in general; it also gives a preview of the potential contribution of vector and parallel computing to heat transfer. Contributions have been made from the fields of heat transfer, computational fluid mechanics or physics, and from researchers in industry or in academia. This work serves to indicate that new or modified numerical algorithms have to be developed depending on the hardware used (as the long titles of most of the papers in this volume imply). This volume contains six examples of numerical simulation on parallel and vector computers that demonstrate the competitiveness of the novel methodologies. A common thread through all the manuscripts is that they address problems involving irregular geometries or complex physics, or both. Comparative studies of the performance of certain algorithms on various computers are also presented. Most machines used in this work belong to the coarse- to medium-grain group (consisting of a few to a hundred processors) with architectures of the multiple-instruction-stream-multiple- data-stream (MIMD) type. Some of the machines used have both parallel and vector processors, while parallel computations are certainly emphasized. We hope that this work will contribute to the increasing involvement of heat transfer specialists with parallel computation.
Enhanced condensation heat transfer with wettability patterning
NASA Astrophysics Data System (ADS)
Sinha Mahapatra, Pallab; Ghosh, Aritra; Ganguly, Ranjan; Megaridis, Constantine
2015-11-01
Condensation of water vapor on metal surfaces is useful for many engineering applications. A facile and scalable method is proposed for removing condensate from a vertical plate during dropwise condensation (DWC) in the presence of non-condensable gases (NCG). We use wettability-patterned superhydrophilic tracks (filmwise condensing domains) on a mirror-finish (hydrophilic) aluminum surface that promotes DWC. Tapered, horizontal ``collection'' tracks are laid to create a Laplace pressure driven flow, which collects condensate from the mirror-finish domains and sends it to vertical ``drainage tracks'' for gravity-induced shedding. An optimal design is achieved by changing the fractional area of superhydrophilic tracks with respect to the overall plate surface, and augmenting capillary-driven condensate-drainage by adjusting the track spatial layout. The design facilitates pump-less condensate drainage and enhances DWC heat transfer on the mirror-finish regions. The study highlights the relative influences of the promoting and retarding effects of dropwise and filmwise condensation zones on the overall heat transfer improvement on the substrate. The study demonstrated ~ 34% heat transfer improvement on Aluminum surface for the optimized design.
Pressure loss and heat transfer in a toothed finned heat transfer medium
NASA Astrophysics Data System (ADS)
Ebeling, W. D.; Leidinger, B. J. G.
Thermohydraulic investigation was carried out in a special toothed-finned geometry, which was provided for increasing heat transfer in an evaporator cooler. The evaporator cooler has applications in space navigation. The toothed-finned heat carrier was used in a counter current, with a view to simplifying the heat transfer coefficient evaluation, from the temperature and volume flows measured. Test results obtained confirmed the suitability of this test arrangement. Relationships were derived from test results, for the pressure loss coefficient and the Nusselt number, with regard to the Reynolds number for this determined finned geometry.
Visualization study on pool boiling heat transfer
NASA Astrophysics Data System (ADS)
Kamei, Shuya; Hirata, Masaru
1991-04-01
The visualized boiling phenomena were observed by means of high speed photographic shadowgraphy using a rotating prism camera (nac HIGH SPEED CAMERA model-16HD) with the speed of about 3500 frames per second. The photographs show that pool boiling heat transfer phenomena are varied for the boiling curve based on the experiments. Experiments have been carried out to investigate pool boiling heat transfer phenomena on a horizontal thin filament in subcooled and saturated distilled water. The experiments were performed for atmospheric pressure,for filament diameters of about 0.3 mm, for region of natural convection to film boiling. The color-film made by high speed movie camera are converted to high speed color video-tape. It is convenient to edit and show the tape for visualization with teaching the students. The high speed color video showed that the successive motion and shape of bubbles during their process of detachment varied with increasing heat flux on the heated surface of a filament. From these results, it was confirmed that the high speed phenomena of boiling by the slow motion video pictures could be estimated clearly.
An experimental study of the flow and heat transfer between enhanced heat transfer plates for PHEs
Li, Xiao-wei; Meng, Ji-an; Li, Zhi-xin
2010-11-15
The flow and heat transfer between inclined discrete rib plates for plate heat exchangers have been experimentally studied. Dye injection method is used to visualize the flow structures. The visualization results show that front vortex, rear vortex and main vortex are formed between the plates. The rib parameter influence is also studied using visualization method. The pressure drop and heat transfer between the inclined discrete rib plates as well as that between inclined continuous rib plates and smooth plates are also measured. The measured results show that the inclined discrete rib plate can enhanced heat transfer 20-25% at the same pumping power compared with the commonly used inclined continuous rib plates. (author)
Heat transfer characteristics of tube bundles during boiling in vacuum
NASA Astrophysics Data System (ADS)
Slesarenko, V. N.; Zakharov, G. A.
1992-06-01
Heat transfer during boiling in vacuum was compared experimentally for single tubes, rows of tube, and tube bundles to analyze characteristic properties of vaporization under such conditions. Relations for calculating heat transfer coefficients are proposed.
Thermal Storage and Advanced Heat Transfer Fluids (Fact Sheet)
Not Available
2010-08-01
Fact sheet describing NREL CSP Program capabilities in the area of thermal storage and advanced heat transfer fluids: measuring thermophysical properties, measuring fluid flow and heat transfer, and simulating flow of thermal energy and fluid.
Measuring Furnace/Sample Heat-Transfer Coefficients
NASA Technical Reports Server (NTRS)
Rosch, William R.; Fripp, Archibald L., Jr.; Debnam, William J., Jr.; Woodell, Glenn A.
1993-01-01
Complicated, inexact calculations now unnecessary. Device called HTX used to simulate and measure transfer of heat between directional-solidification crystal-growth furnace and ampoule containing sample of crystalline to be grown. Yields measurement data used to calculate heat-transfer coefficients directly, without need for assumptions or prior knowledge of physical properties of furnace, furnace gas, or specimen. Determines not only total heat-transfer coefficients but also coefficients of transfer of heat in different modes.
Heat Transfer Through Turbulent Friction Layers
NASA Technical Reports Server (NTRS)
Reichardt, H.
1943-01-01
The "general Prandtl number" Pr(exp 1) - A(sub q)/A Pr, aside from the Reynolds number determines the ratio of turbulent to molecular heat transfer, and the temperature distribution in turbulent friction layers. A(sub q) = exchange coefficient for heat; A = exchange coefficient for momentum transfer. A formula is derived from the equation defining the general Prandtl number which describes the temperature as a function of the velocity. For fully developed thermal boundary layers all questions relating to heat transfer to and from incompressible fluids can be treated in a simple manner if the ratio of the turbulent shear stress to the total stress T(sub t)/T in the layers near the wall is known, and if the A(sub q)/A can be regarded as independent of the distance from the wall. The velocity distribution across a flat smooth channel and deep into the laminar sublayer was measured for isothermal flow to establish the shear stress ratio T(sub t)/T and to extend the universal wall friction law. The values of T(sub t)/T which resulted from these measurements can be approximately represented by a linear function of the velocity in the laminar-turbulent transition zone. The effect of the temperature relationship of the material values on the flow near the wall is briefly analyzed. It was found that the velocity at the laminar boundary (in contrast to the thickness of the laminar layer) is approximately independent of the temperature distribution. The temperature gradient at the wall and the distribution of temperature and heat flow in the turbulent friction layers were calculated on the basis of the data under two equations. The derived formulas and the figures reveal the effects of the Prandtl number, the Reynolds number, the exchange quantities and the temperature relationship of the material values.
Enhancement of heat and mass transfer by cavitation
NASA Astrophysics Data System (ADS)
Zhang, Y. N.; Zhang, Y. N.; Du, X. Z.; Xian, H. Z.
2015-01-01
In this paper, a brief summary of effects of cavitation on the heat and mass transfer are given. The fundamental studies of cavitation bubbles, including its nonlinearity, rectified heat and mass diffusion, are initially introduced. Then selected topics of cavitation enhanced heat and mass transfer were discussed in details including whales stranding caused by active sonar activity, pool boiling heat transfer, oscillating heat pipe and high intensity focused ultrasound treatment.
Heat Transfer in Glass, Aluminum, and Plastic Beverage Bottles
ERIC Educational Resources Information Center
Clark, William M.; Shevlin, Ryan C.; Soffen, Tanya S.
2010-01-01
This paper addresses a controversy regarding the effect of bottle material on the thermal performance of beverage bottles. Experiments and calculations that verify or refute advertising claims and represent an interesting way to teach heat transfer fundamentals are described. Heat transfer coefficients and the resistance to heat transfer offered…
Film-Cooling Heat-Transfer Measurements Using Liquid Crystals
NASA Technical Reports Server (NTRS)
Hippensteele, Steven A.
1997-01-01
The following topics are discussed: (1) The Transient Liquid-Crystal Heat-Transfer Technique; (2) 2-D Film-Cooling Heat-Transfer on an AlliedSignal Vane; and (3) Effects of Tab Vortex Generators on Surface Heat Transfer. Downstream of a Jet in Crossflow.
Low heat transfer oxidizer heat exchanger design and analysis
NASA Technical Reports Server (NTRS)
Kanic, P. G.; Kmiec, T. D.; Peckham, R. J.
1987-01-01
The RL10-IIB engine, a derivative of the RLIO, is capable of multi-mode thrust operation. This engine operates at two low thrust levels: tank head idle (THI), which is approximately 1 to 2 percent of full thrust, and pumped idle (PI), which is 10 percent of full thrust. Operation at THI provides vehicle propellant settling thrust and efficient engine thermal conditioning; PI operation provides vehicle tank pre-pressurization and maneuver thrust for log-g deployment. Stable combustion of the RL10-IIB engine at THI and PI thrust levels can be accomplished by providing gaseous oxygen at the propellant injector. Using gaseous hydrogen from the thrust chamber jacket as an energy source, a heat exchanger can be used to vaporize liquid oxygen without creating flow instability. This report summarizes the design and analysis of a United Aircraft Products (UAP) low-rate heat transfer heat exchanger concept for the RL10-IIB rocket engine. The design represents a second iteration of the RL10-IIB heat exchanger investigation program. The design and analysis of the first heat exchanger effort is presented in more detail in NASA CR-174857. Testing of the previous design is detailed in NASA CR-179487.
D0 Silicon Upgrade: 3 Chip Ladder Heat Transfer
Ratzmann, Paul; /Fermilab
1994-09-19
The Silicon Mechanical group has submitted a 3 chip ladder drawing to the Fermilab Analysis Group (Zhijing Tang) to determine the temperature distribution in the ladder during detector operation. Heat transfer by convection and radiation is assumed negligible and two dimensional PEA conduction solutions were performed. The heat flux at the SVX IT chip region is assumed to be 8.359 mW/mm{sup 2} which corresponds to roughly 0.48 W per SVX II chip. The heat flux in the region of the transceiver is assumed 8.801 mW/mm{sup 2}, corresponding to 1.6 W in this region. Total heat load of the 3 chip ladder is assumed to be 3.04 W. The 3 chip ladder submitted for analysis is shown in the figure below. The multichip module (MCM) is mounted on beryllium plate which serves to carry the heat load of the chips and the transceiver to the cooling channel. Adhesive thermal conductivity is 1.6 W/m-K, based on the published value of the selected adhesive. Actual measurements of thermally conductive adhesives indicate that the assumed 1.6 W/m-K is high. Experience gained in measuring adhesive thermal conductivity indicates 0.9-1.2 W/m-K as a more reasonable number to use. The effect of the uncertainty of the adhesive thermal conductivity on silicon temperature is discussed.
Heat transfer model for quenching by submerging
NASA Astrophysics Data System (ADS)
Passarella, D. N.; Varas, F.; Martín, E. B.
2011-05-01
In quenching by submerging the workpiece is cooled due to vaporization, convective flow and interaction of both mechanisms. The dynamics of these phenomena is very complex and the corresponding heat fluxes are strongly dependent on local flow variables such as velocity of fluid and vapor fraction. This local dependence may produce very different cooling rates along the piece, responsible for inappropriate metallurgical transformations, variability of material properties and residual stresses. In order to obtain an accurate description of cooling during quenching, a mathematical model of heat transfer is presented here. The model is based on the drift-flux mixture-model for multiphase flows, including an equation of conservation of energy for the liquid phase and specific boundary conditions that account for evaporation and presence of vapor phase on the surface of the piece. The model was implemented on Comsol Multiphysics software. Generation of appropriate initial and boundary conditions, as well as numerical resolution details, is briefly discussed. To test the model, a simple flow condition was analyzed. The effect of vapor fraction on heat transfer is assessed. The presence of the typical vapor blanket and its collapse can be recovered by the model, and its effect on the cooling rates on different parts of the piece is analyzed. Comparisons between numerical results and data from literature are made.
Thermochromic liquid crystals in heat transfer research
NASA Astrophysics Data System (ADS)
Stasiek, Jan A.; Kowalewski, Tomasz A.
2002-06-01
In recent years Thermochromic Liquid Crystals (TLC) have been successfully used in non-intrusive heat transfer and fluid mechanics studies. Thin coatings of TLC's at surfaces is utilized to obtain detailed heat transfer data of steady or transient process. Application of TLC tracers allows instantaneous measurement of the temperature and velocity fields for two-dimensional cross-section of flow. Computerized flow visualization techniques allow automatic quantification of temperature of the analyzed surface or the visualized flow cross-section. Here we describe our experience in applying the method to selected problems studied in our laboratory. They include modeling flow configurations in the differentially heated inclined cavity with vertical temperature gradient simulating up-slope flow as well as thermal convection under freezing surface. The main aim of these experimental models is to generate reliable experimental database on velocity and temperature fields for specific flow. The methods are based on computerized true-color analysis of digital images for temperature measurements and modified Particle Image Velocimetry and Thermometry (PIVT) used to obtain the flow field velocity.
Laminar heat transfer in annular sector ducts
Soliman, H.M. )
1987-02-01
The continuing interest in compact heat exchangeers has created the need for friction factor and Nusselt number data for different passage shapes. It has long been recognized that circular tube results are generally not applicable to noncircular passages even when the hydraulic diameter is used as the characteristic dimension. Hence, design data should be generated for each passage individually, and a good source of such information is Shah and London. One duct geometry for which complete design information does not appear to be available in the open literature is that of annular sector ducts. Such configuration is encountered in multipassage internally finned tubes and many other compact het exchanger applications. The fluid flow problem for this configuration has been solved by Sparrow et al., and more recently by Niida. However, to the beest of the author's knowledge, the heat transfer results are not available yet. The purpose of this note is to summarize the analysis and results of fluid flow and heat transfer in annular sector ducts.
Heat transfer in circulating fluidized bed combustor
Bucak, O.; Dogan, O.M.; Uysal, B.Z.
1999-07-01
The importance of fluidized bed combustion in utilizing the energy of especially low quality coals is widely accepted. Among various fluidized bed combustion technologies, circulating fluidized beds are preferred as a result of the efforts to get higher combustion efficiencies. The aim of the present research was to investigate the applicability of this technology to Turkish lignites. To achieve this object a 6.5 m tall pilot circulating fluidized bed combustor with 155 mm diameter and all the auxiliary equipment were designed, constructed and tested using Seyitomer lignite of 0.9--2.38 mm in size. Heat transfer from the bed to the water cooling jackets was examined to recover the combustion energy. The inside heat transfer coefficient was determined to be around 121 W/m{sup 2} K for the suspension density of 20--55 kg/m{sup 3}. The agreement of the experimental findings with theoretical estimations was also checked. Furthermore, the thermal efficiency of the system for the heat recovered was found to be 63%.
Heat transfer to a supercritical hydrocarbon fuel with endothermic reaction.
Yu, W.; France, D. M.; Wambsganss, M. W.; Energy Technology; Univ. of Illinois at Chicago
2000-01-01
Supercritical fuel reforming is being studied as a technology for reducing emissions of industrial gas turbine engines. In this study, experiments were performed in a 2.67-mm-inside-diameter stainless steel tube with a heated length of 0.610 m for the purpose of investigating the characteristics of supercritical heat transfer with endothermic fuel reforming. Thermocouples were positioned along the tube both in the fluid stream and on the heated wall for local heat transfer measurements. Both heat transfer coefficients and endotherms were calculated from the measured results. State-of-the-art correlations for heat transfer were evaluated, and a correlation for supercritical heat transfer to hydrocarbon fuel has been developed. The results provide a basis for supercritical fuel heat-exchanger/reactor design and its practical applications, in an area that has received relatively little attention in the engineering literature, viz., supercritical forced convection heat transfer with endothermic chemical reaction.
Meaningful wind chill indicators derived from heat transfer principles.
Brauner, N; Shacham, M
1995-08-01
The wind chill index (WCI) and the more widely used wind chill equivalent temperature represent an attempt to combine several weather-related variables (temperature, wind velocity and solar radiation) into a single index which can indicate human comfort. Since its introduction in 1945, the WCI has been criticized mainly on the ground that the underlying model does not comply with modern heat transfer theory. In spite of that, the WCI, "calibrated" to human comfort, has proven to be successful in predicting discomfort and tolerance of man to the cold. Nevertheless, neither the WCI nor the wind chill equivalent temperature can be actually measured and, therefore, without the additional 'calibration' they are meaningless. In this study we have shown that the WCI represents the instantaneous rate of heat loss from bare skin at the moment of exposure to the cold, and as such, it correlates reasonably well with measurable variables that represent a feeling of cold. Two new wind chill indicators have been introduced: exposed skin temperature and maximum exposure time. These indicators yield more information than the WCI provides, are measurable, have physical meaning and are based on established heat transfer principles. PMID:7558408
Meaningful wind chill indicators derived from heat transfer principles
NASA Astrophysics Data System (ADS)
Brauner, Neima; Shacham, M.
1995-03-01
The wind chill index (WCI) and the more widely used wind chill equivalent temperature represent an attempt to combine several weather-related variables (temperature, wind velocity and solar radiation) into a single index which can indicate human comfort. Since its introduction in 1945, the WCI has been criticized mainly on the ground that the underlying model does not comply with modern heat transfer theory. In spite of that, the WCI, “calibrated” to human comfort, has proven to be successful in predicting discomfort and tolerance of man to the cold. Nevertheless, neither the WCI nor the wind chill equivalent temperature can be actually measured and, therefore, without the additional ‘calibration’ they are meaningless. In this study we have shown that the WCI represents the instantaneous rate of heat loss from bare skin at the moment of exposure to the cold, and as such, it correlates reasonably well with measurable variables that represent a feeling of cold. Two new wind chill indicators have been introduced: exposed skin temperature and maximum exposure time. These indicators yield more information than the WCI provides, are measurable, have physical meaning and are based on established heat transfer principles.
Advances in refrigeration and heat transfer engineering
Bansal, Pradeep; Cremaschi, Prof. Lorenzo
2015-05-13
This special edition of Science and Technology for the Built Environment (STBE) presents selected high quality papers that were presented at the 15th International Refrigeration and Air Conditioning Conference held at Purdue University during July 14-17 2014. All papers went through the additional review before being finally accepted for publication in this special issue of Science and Technology and the Built Environment. Altogether 20 papers made to this special issue that cover a wide range of topics, including advancements in alternative refrigerants, heat exchangers/heat transfer, nano-fluids, systems design and optimization and modeling approaches. Although CO2 may perhaps have been themore » most researched and popular refrigerant in the past decade, R32 is being seriously considered lately as an alternative and environmentally friendly refrigerant for small systems due to its low Global Warming Potential (GWP).« less
USINT. Heat and Mass Transfer In Concrete
Eyberger, L.R.
1989-12-01
USINT was developed to model the thermal response of concrete to very high heating rates such as might occur from sodium spills on concrete surfaces in a breeder reactor. The major phenomena treated are conductive energy transport; chemical decomposition of concrete; and two-phase, three-component heat and mass transfer of the decomposition products: steam, liquid water, and carbon dioxide. The USINT model provides for porosity to increase as water and carbon-dioxide are formed from the concrete. The concrete is treated generally as divided into two basic regions, wet and dry. In the wet region, steam, carbon-dioxide, and liquid water may co-exist, but in the dry region, there is no liquid water. There is also the possibility of a third region in which there is only liquid water and no gases.
USINT. Heat and Mass Transfer in Concrete
Beck, J.V.; Knight, R.L.
1989-12-01
USINT was developed to model the thermal response of concrete to very high heating rates such as might occur from sodium spills on concrete surfaces in a breeder reactor. The major phenomena treated are conductive energy transport; chemical decomposition of concrete; and two-phase, three-component heat and mass transfer of the decomposition products: steam, liquid water, and carbon dioxide. The USINT model provides for porosity to increase as water and carbon-dioxide are formed from the concrete. The concrete is treated generally as divided into two basic regions, wet and dry. In the wet region, steam, carbon-dioxide, and liquid water may co-exist, but in the dry region, there is no liquid water. There is also the possibility of a third region in which there is only liquid water and no gases.
3-D Finite Element Heat Transfer
1992-02-01
TOPAZ3D is a three-dimensional implicit finite element computer code for heat transfer analysis. TOPAZ3D can be used to solve for the steady-state or transient temperature field on three-dimensional geometries. Material properties may be temperature-dependent and either isotropic or orthotropic. A variety of time-dependent and temperature-dependent boundary conditions can be specified including temperature, flux, convection, and radiation. By implementing the user subroutine feature, users can model chemical reaction kinetics and allow for any type of functionalmore » representation of boundary conditions and internal heat generation. TOPAZ3D can solve problems of diffuse and specular band radiation in an enclosure coupled with conduction in the material surrounding the enclosure. Additional features include thermal contact resistance across an interface, bulk fluids, phase change, and energy balances.« less
Advances in refrigeration and heat transfer engineering
Bansal, Pradeep; Cremaschi, Prof. Lorenzo
2015-05-13
This special edition of Science and Technology for the Built Environment (STBE) presents selected high quality papers that were presented at the 15th International Refrigeration and Air Conditioning Conference held at Purdue University during July 14-17 2014. All papers went through the additional review before being finally accepted for publication in this special issue of Science and Technology and the Built Environment. Altogether 20 papers made to this special issue that cover a wide range of topics, including advancements in alternative refrigerants, heat exchangers/heat transfer, nano-fluids, systems design and optimization and modeling approaches. Although CO_{2} may perhaps have been the most researched and popular refrigerant in the past decade, R32 is being seriously considered lately as an alternative and environmentally friendly refrigerant for small systems due to its low Global Warming Potential (GWP).
Heat transfer augmentation in nanofluids via nanofins.
Vadasz, Peter
2011-01-01
Theoretical results derived in this article are combined with experimental data to conclude that, while there is no improvement in the effective thermal conductivity of nanofluids beyond the Maxwell's effective medium theory (J.C. Maxwell, Treatise on Electricity and Magnetism, 1891), there is substantial heat transfer augmentation via nanofins. The latter are formed as attachments on the hot wire surface by yet an unknown mechanism, which could be related to electrophoresis, but there is no conclusive evidence yet to prove this proposed mechanism. PMID:21711695
Heat transfer augmentation in nanofluids via nanofins
2011-01-01
Theoretical results derived in this article are combined with experimental data to conclude that, while there is no improvement in the effective thermal conductivity of nanofluids beyond the Maxwell's effective medium theory (J.C. Maxwell, Treatise on Electricity and Magnetism, 1891), there is substantial heat transfer augmentation via nanofins. The latter are formed as attachments on the hot wire surface by yet an unknown mechanism, which could be related to electrophoresis, but there is no conclusive evidence yet to prove this proposed mechanism. PMID:21711695
Solar Pond Fluid Dynamics and Heat Transfer
NASA Technical Reports Server (NTRS)
Jones, G. F.
1984-01-01
The primary objective of the solar pond research was to obtain an indepth understanding of solar pond fluid dynamics and heat transfer. The key product was the development of a validated one-dimensional computer model with the capability to accurately predict time-dependent solar pond temperature, salinities, and interface motions. Laboratory scale flow visualization experiments were conducted to better understand layer motion. Two laboratory small-scale ponds and a large-scale outdoor solar pond were designed and built to provide quantitative data. This data provided a basis for validating the model and enhancing the understanding of pond dynamic behavior.
Porous media heat transfer for injection molding
Beer, Neil Reginald
2016-05-31
The cooling of injection molded plastic is targeted. Coolant flows into a porous medium disposed within an injection molding component via a porous medium inlet. The porous medium is thermally coupled to a mold cavity configured to receive injected liquid plastic. The porous medium beneficially allows for an increased rate of heat transfer from the injected liquid plastic to the coolant and provides additional structural support over a hollow cooling well. When the temperature of the injected liquid plastic falls below a solidifying temperature threshold, the molded component is ejected and collected.
Flow and heat transfer in a curved channel
NASA Technical Reports Server (NTRS)
Brinich, P. F.; Graham, R. W.
1977-01-01
Flow and heat transfer in a curved channel of aspect ratio 6 and inner- to outer-wall radius ratio 0.96 were studied. Secondary currents and large longitudinal vortices were found. The heat-transfer rates of the outer and inner walls were independently controlled to maintain a constant wall temperature. Heating the inner wall increased the pressure drop along the channel length, whereas heating the outer wall had little effect. Outer-wall heat transfer was as much as 40 percent greater than the straight-channel correlation, and inner-wall heat transfer was 22 percent greater than the straight-channel correlation.
Heat transfer analysis in rotating sphericall shells
NASA Astrophysics Data System (ADS)
Cabello, Ares; Avila, Ruben
2015-11-01
The study of flow patterns within rotating spherical annular geometries with natural convection, is essential to understand the internal dynamics of the planets. We investigate the convective flows and the heat transfer rate in an spherical gap in which a temperature difference between the inner sphere and the outer sphere is present. A self gravity field which varies as a function of 1 /rn (where r is the radial position and the integer exponent n has the values 2,3,4,5) is assumed. The Boussinesq fluid equations are solved by using a spectral element method (SEM). To avoid the singularity at the poles, the cubed-sphere algorithm is used to generate the spherical mesh. Heat fluxes at the surface of both spheres are analyzed. We find, for several Ekman and Rayleigh numbers, that there exists a high correlation between the azimuthal motion of both the Busse cells and the zones where the maximum surface heat fluxes occur. The azimuthal position, as a function of time, of the maximum heat flux zones (which are located symmetrically with respect to the equator), allows to speculate on the nature of the phenomena occurring (in geological times) on the surface of the terrestrial planets. Thanks to DGAPA-PAPIIT project: IN117314-3.
Thermodynamics of flame impingement heat transfer
NASA Astrophysics Data System (ADS)
Som, S. K.; Agrawal, G. K.; Chakraborty, Suman
2007-08-01
A theoretical model for entropy generation and utilization of work potential (exergy) in flame impingement (both premixed and diffusion) heat transfer has been developed in this article, to offer physical insights on the optimal operational regimes, depicting high values of the surface heat flux with minimal exergy destruction, within the practical constraints. The irreversibility components due to different physical processes have been evaluated from a general entropy transport equation. The velocity, temperature, and species concentration fields required for the solution of entropy transport equation have been determined from the numerical computation of flow-field in the flame. Global two-step chemical kinetics has been considered with methane (CH4) and air as fuel and oxidizer, respectively. The results have been predicted in terms of average nondimensional heat flux, expressed as Nusselt number at the target plate, the irreversibility components, and second law efficiency, as functions of the pertinent input parameters such as the jet Reynolds number and the ratio of plate separation distance to nozzle diameter (H /d). The average Nusselt number has been found to increase with an increase in jet Reynolds number and a decrease in H /d ratio, up to a value of 8. The dominant source of thermodynamic irreversibility in a premixed flame has been attributed to the thermal energy exchange whereas, in a diffusion flame, the same has been attributed to an uncontrolled exchange of electrons accompanying the reactive kinetics. The second law efficiency has been found to increase with an increase in jet Reynolds number and an increase in the H /d ratio, up to a value of 20. Values of the jet Reynolds number greater than 10 000 and H /d ratio in the tune of 15 have been observed to pertain to the regime of optimum flame impingement heat transfer, consistent with the energy and exergy balance constraints.
Measurement of local connective heat transfer coefficients of four ice accretion shapes
NASA Technical Reports Server (NTRS)
Smith, M. E.; Armilli, R. V.; Keshock, E. G.
1984-01-01
In the analytical study of ice accretions that form on aerodynamic surfaces (airfoils, engine inlets, etc.) it is often necessary to be able to calculate convective heat transfer rates. In order to do this, local convective heat transfer coefficients for the ice accretion shapes must be known. In the past, coefficients obtained for circular cylinders were used as an approximation to the actual coefficients since no better information existed. The purpose of this experimental study was to provide local convective heat transfer coefficients for four shapes that represent ice accretions. The shapes were tested with smooth and rough surfaces. The experimental method chosen was the thin-skin heat rate technique. Using this method local Nusselt numbers were determined for the ice shapes. In general it was found that the convective heat transfer was higher in regions where the model's surfaces were convex and lower in regions where the model's surfaces were concave. The effect of roughness was to increase the heat transfer in the high heat transfer regions by approximately 100% while little change was apparent in the low heat transfer regions.
NASA Technical Reports Server (NTRS)
McCloud, Peter L.
2010-01-01
Thermal Protection System (TPS) Cavity Heating is predicted using Computational Fluid Dynamics (CFD) on unstructured grids for both simplified cavities and actual cavity geometries. Validation was performed using comparisons to wind tunnel experimental results and CFD predictions using structured grids. Full-scale predictions were made for simplified and actual geometry configurations on the Space Shuttle Orbiter in a mission support timeframe.
Nanoscale heat transfer and phase transformation surrounding intensely heated nanoparticles
NASA Astrophysics Data System (ADS)
Sasikumar, Kiran
Over the last decade there has been significant ongoing research to use nanoparticles for hyperthermia-based destruction of cancer cells. In this regard, the investigation of highly non-equilibrium thermal systems created by ultrafast laser excitation is a particularly challenging and important aspect of nanoscale heat transfer. It has been observed experimentally that noble metal nanoparticles, illuminated by radiation at the plasmon resonance wavelength, can act as localized heat sources at nanometer-length scales. Achieving biological response by delivering heat via nanoscale heat sources has also been demonstrated. However, an understanding of the thermal transport at these scales and associated phase transformations is lacking. A striking observation made in several laser-heating experiments is that embedded metal nanoparticles heated to extreme temperatures may even melt without an associated boiling of the surrounding fluid. This unusual phase stability is not well understood and designing experiments to understand the physics of this phenomenon is a challenging task. In this thesis, we will resort to molecular dynamics (MD) simulations, which offer a powerful tool to investigate this phenomenon, without assumptions underlying continuum-level model formulations. We present the results from a series of steady state and transient non-equilibrium MD simulations performed on an intensely heated nanoparticle immersed in a model liquid. For small nanoparticles (1-10 nm in diameter) we observe a stable liquid phase near the nanoparticle surface, which can be at a temperature well above the boiling point. Furthermore, we report the existence of a critical nanoparticle size (4 nm in diameter) below which we do not observe formation of vapor even when local fluid temperatures exceed the critical temperature. Instead, we report the existence of a stable fluid region with a density much larger than that of the vapor phase. We explain this stability in terms of the
Heat Transfer Phenomena in Supercritical Water Nuclear Reactors
Mark H. Anderson; MichaelL. Corradini; Riccardo Bonazza; Jeremy R. Licht
2007-10-03
A supercritical water heat transfer facility has been built at the University of Wisconsin to study heat transfer in ancircular and square annular flow channel. A series of integral heat transfer measurements has been carried out over a wide range of heat flux, mas velocity and bulk water temperatures at a pressure of 25 MPa. The circular annular test section geometry is a 1.07 cm diameter heater rod within a 4.29 diameter flow channel.
Heat Transfer in High Temperature Multilayer Insulation
NASA Technical Reports Server (NTRS)
Daryabeigi, Kamran; Miller, Steve D.; Cunnington, George R.
2007-01-01
High temperature multilayer insulations have been investigated as an effective component of thermal-protection systems for atmospheric re-entry of reusable launch vehicles. Heat transfer in multilayer insulations consisting of thin, gold-coated, ceramic reflective foils and Saffil(TradeMark) fibrous insulation spacers was studied both numerically and experimentally. A finite volume numerical thermal model using combined conduction (gaseous and solid) and radiation in porous media was developed. A two-flux model with anisotropic scattering was used for radiation heat transfer in the fibrous insulation spacers between the reflective foils. The thermal model was validated by comparison with effective thermal conductivity measurements in an apparatus based on ASTM standard C201. Measurements were performed at environmental pressures in the range from 1x10(exp -4) to 760 torr over the temperature range from 300 to 1300 K. Four multilayer samples with nominal densities of 48 kg/cu m were tested. The first sample was 13.3 mm thick and had four evenly spaced reflective foils. The other three samples were 26.6 mm thick and utilized either one, two, or four reflective foils, located near the hot boundary with nominal foil spacing of 1.7 mm. The validated thermal model was then used to study relevant design parameters, such as reflective foil spacing and location in the stack-up and coating of one or both sides of foils.
Nucleation and Heat Transfer in Liquid Nitrogen
NASA Astrophysics Data System (ADS)
Roth, Eric Warner
1993-01-01
With the advent of the new high Tc superconductors as well as the increasing use of cryo-cooled conventional electronics, liquid nitrogen will be one of the preferred cryogens used to cool these materials. Consequently, a more thorough understanding of the heat transfer characteristics of liquid nitrogen is required. In these investigations the transient heating characteristics of liquid nitrogen to states of nucleate and film boiling under different liquid flow conditions are examined. Using a metal hot wire/plate technique, it is verified that there is a premature transition to film boiling in the transient case at power levels as much as 30 percent lower than under steady state nucleate boiling conditions. It is also shown that the premature transition can be reduced or eliminated depending on the flow velocity. The second part of this research analyses the nucleation (boiling) process from a dynamical systems point of view. By observing how the boiling system variables evolve and fluctuate over time, it is hoped that physical insight and predictive information can be gained. One goal is to discover some indicator or signature in the data that anticipates the transition from nucleate boiling to film boiling. Some of the important variables that make up the boiling system are the temperature of the heater and the heat flux through the heater surface into the liquid nitrogen. The result, gained by plotting the system's trajectory in the heat flux-temperature plane, is that on average the system follows a counterclockwise trajectory. A physical model is constructed that explains this behavior. Also, as the applied heater power approaches levels at which the transition to film is known to occur, the area per unit time swept out in the heat flux-temperature plane is seen to reach a maximum. This could be of practical interest as the threshold to film boiling can be anticipated and possibly prevented.
Wei, Wenjian; Ding, Guoliang; Hu, Haitao; Wang, Kaijian
2007-10-15
The predictive ability of the available state-of-the-art heat transfer correlations of refrigerant-oil mixture is evaluated with the present experiment data of small tubes with inside diameter of 6.34 mm and 2.50 mm. Most of these correlations can be used to predict the heat transfer coefficient of 6.34 mm tube, but none of them can predict heat transfer coefficient of 2.50 mm tube satisfactorily. A new correlation of two-phase heat transfer multiplier with local properties of refrigerant-oil mixture is developed. This correlation approaches the actual physical mechanism of flow boiling heat transfer of refrigerant-oil mixture and can reflect the actual co-existing conditions of refrigerant and lubricant oil. More than 90% of the experiment data of both test tubes have less than {+-}20% deviation from the prediction values of the new correlations. (author)
A convective and radiative heat transfer analysis for the FIRE II forebody
NASA Technical Reports Server (NTRS)
Greendyke, Robert B.; Hartung, Lin C.
1993-01-01
A Navier-Stokes flowfield solution method (LAURA code) using finite-rate chemistry and two-temperature thermal nonequilibrium was used in combination with two nonequilibrium radiative heat transfer codes to calculate heating for the FIRE II vehicle. An axisymmetric model of the actual body shape was used. One radiative heating code (NEQAIR) was used in uncoupled fashion with the flowfield solver's energy equations, while the other code (LORAN) was used in both coupled and uncoupled variations. Several trajectory points ranging from highly nonequilibrium flow to near-equilibrium flow were used for a study of both convective and radiative heating over the vehicle. Considerable variation in radiative heating was seen at the extremes, while agreement was good in the intermediate trajectory points. Total heat transfer calculations gave good comparison until the peak heating trajectory points were encountered, and returned to good agreement for the last two equilibrium points.
Transient critical heat flux and blowdown heat-transfer studies
Leung, J.C.
1980-05-01
Objective of this study is to give a best-estimate prediction of transient critical heat flux (CHF) during reactor transients and hypothetical accidents. To accomplish this task, a predictional method has been developed. Basically it involves the thermal-hydraulic calculation of the heated core with boundary conditions supplied from experimental measurements. CHF predictions were based on the instantaneous ''local-conditions'' hypothesis, and eight correlations (consisting of round-tube, rod-bundle, and transient correlations) were tested against most recent blowdown heat-transfer test data obtained in major US facilities. The prediction results are summarized in a table in which both CISE and Biasi correlations are found to be capable of predicting the early CHF of approx. 1 s. The Griffith-Zuber correlation is credited for its prediction of the delay CHF that occurs in a more tranquil state with slowly decaying mass velocity. In many instances, the early CHF can be well correlated by the x = 1.0 criterion; this is certainly indicative of an annular-flow dryout-type crisis. The delay CHF occurred at near or above 80% void fraction, and the success of the modified Zuber pool-boiling correlation suggests that this CHF is caused by flooding and pool-boiling type hydrodynamic crisis.
Inelastic Heat Transfer in Molecular Quantum Dots
NASA Astrophysics Data System (ADS)
Dyrkacz, Joanna; Walczak, Kamil
We examine electronic heat conduction via molecular complexes in the presence of local electron-phonon coupling effects. In off-resonance transport regime, even weak electron-phonon interactions lead to phonon-mediated changes of transport characteristics. In the nearly resonance conditions, the strong electron-phonon coupling reduces the height of the main conductance peak, generating additional satellites (phonon sidebands) in transport characteristics and shifting molecular energy spectrum via reorganization (polaron) energy. In the past, it was shown that inclusion of electron-phonon coupling effects into computational scheme reduces discrepancy between theoretical results and experimental data. The aim of this project is to study electron-phonon coupling effects on electronic heat transfer at molecular level. For that purpose, we use non-perturbative computational scheme based on inelastic version of Landauer formula, where the Green's functions technique combined with polaron transformation was used to calculate multi-channel transmission probability function, while accessibility of individual conduction channels is governed by Boltzmann statistics. Our analysis is based on the hypothesis that the dynamics created by electron-phonon interaction onto the molecular quantum dot asymmetrically connected to two thermal reservoirs will lead to thermal rectification effect. Our results will be discussed in a few aspects: electron-phonon coupling strength, phonon dispersion relationship, and heat fluxes generated by temperature difference as well as bias voltage.
Boiling local heat transfer enhancement in minichannels using nanofluids
2013-01-01
This paper reports an experimental study on nanofluid convective boiling heat transfer in parallel rectangular minichannels of 800 μm hydraulic diameter. Experiments are conducted with pure water and silver nanoparticles suspended in water base fluid. Two small volume fractions of silver nanoparticles suspended in water are tested: 0.000237% and 0.000475%. The experimental results show that the local heat transfer coefficient, local heat flux, and local wall temperature are affected by silver nanoparticle concentration in water base fluid. In addition, different correlations established for boiling flow heat transfer in minichannels or macrochannels are evaluated. It is found that the correlation of Kandlikar and Balasubramanian is the closest to the water boiling heat transfer results. The boiling local heat transfer enhancement by adding silver nanoparticles in base fluid is not uniform along the channel flow. Better performances and highest effect of nanoparticle concentration on the heat transfer are obtained at the minichannels entrance. PMID:23506445
Heat transfer assembly for a fluorescent lamp and fixture
Siminovitch, Michael J.; Rubenstein, Francis M.; Whitman, Richard E.
1992-01-01
In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure.
Heat transfer assembly for a fluorescent lamp and fixture
Siminovitch, M.J.; Rubenstein, F.M.; Whitman, R.E.
1992-12-29
In a lighting fixture including a lamp and a housing, a heat transfer structure is disclosed for reducing the minimum lamp wall temperature of a fluorescent light bulb. The heat transfer structure, constructed of thermally conductive material, extends from inside the housing to outside the housing, transferring heat energy generated from a fluorescent light bulb to outside the housing where the heat energy is dissipated to the ambient air outside the housing. Also disclosed is a method for reducing minimum lamp wall temperatures. Further disclosed is an improved lighting fixture including a lamp, a housing and the aforementioned heat transfer structure. 11 figs.
Study and Analysis of Heat Transfer Limitation of Separated Heat Pipe
NASA Astrophysics Data System (ADS)
Mou, Qizheng; Mou, Kai
2002-01-01
satellite and spacecraft. evaporator, heat isolation and condenser along the axial direction. The working fluid absorbs heat and evaporates in evaporator, and then the vapor flows to condenser and gives out heat. The condensed liquid is pumped to evaporator by wick. By the circulation, the heat can by transferred continuously. heat pipe as follow: - Vapor-liquid two phase flow inside pipe; - The manner of latent heat to transfer heat; - Automatic circulation by working fluid flowing - A certain extent of vacuum. and the traditional heat pipe, that is, the vapor fluid and liquid fluid flow along the same direction. So it is obviously that the separated heat pipe has special internal heat transfer characteristic and crisis. This paper has regard for the heat transfer crisis of the separated heat pipe, and meanwhile relevant calculation and analysis have been done. 1. FLOW TYPE OF THE WORKING FLUID IN SEPARATED HEAT PIPE 2. HEAT TRANSFER CRISIS IN THE EVAPORATOR 3. CARRYING PHENOMENON INSIDE SEPARATED HEAT PIPE 4. THE STAGNANT FLOW PHENOMENON AND THE BACKWARD FLOW PHENOMENON IN EVAPORATOR CONCLUSION transfer limitation of location burn-out, and the heat transfer limitation of flow unconventionality in erective pipe. The carrying phenomenon can occurs not only in evaporator but also in condenser of separated heat pipe. It is in the evaporator that should take place the heat transfer limitation of liquid film dry-out at first. Then with the increasing of heat flux, the heat transfer limitation of location burn-out would happen. In order to avoid the heat transfer limitation of flow unconventionality in erective pipe, the length and diameter of the outflow tube and inflow tube must be reasonably calculated to control the flow velocity of the working fluid inside pipe. Key words:Separated Heat PipeHeat Transfer LimitationDry-OutCarryingStagnancy
46 CFR 153.430 - Heat transfer systems; general.
Code of Federal Regulations, 2010 CFR
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... transfer rate....
46 CFR 153.430 - Heat transfer systems; general.
Code of Federal Regulations, 2014 CFR
2014-10-01
... 46 Shipping 5 2014-10-01 2014-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... transfer rate....
46 CFR 153.430 - Heat transfer systems; general.
Code of Federal Regulations, 2011 CFR
2011-10-01
... 46 Shipping 5 2011-10-01 2011-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... transfer rate....
46 CFR 153.430 - Heat transfer systems; general.
Code of Federal Regulations, 2012 CFR
2012-10-01
... 46 Shipping 5 2012-10-01 2012-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... transfer rate....
7 CFR 3201.54 - Heat transfer fluids.
Code of Federal Regulations, 2014 CFR
2014-01-01
... 7 Agriculture 15 2014-01-01 2014-01-01 false Heat transfer fluids. 3201.54 Section 3201.54... Designated Items § 3201.54 Heat transfer fluids. (a) Definition. Products with high thermal capacities used... transfer fluids. By that date, Federal agencies that have the responsibility for drafting or...
The heat transfer of cooling fins on moving air
NASA Technical Reports Server (NTRS)
Doetsch, Hans
1935-01-01
The present report is a comparison of the experimentally defined temperature and heat output of cooling fins in the air stream with theory. The agreement is close on the basis of a mean coefficient of heat transfer with respect to the total surface. A relationship is established between the mean coefficient of heat transfer, the dimensions of the fin arrangement, and the air velocity.
Heat transfer and fluid friction in bundles of twisted tubes
NASA Astrophysics Data System (ADS)
Dzyubenko, B. V.; Dreitser, G. A.
1986-06-01
The results of heat-transfer and friction studies in bundles of twisted tubes and rods with spiral wire-wrap spacers are analyzed, and recommendations are given for calculating the heat-transfer coefficient in heat exchangers using twisted tubes.
46 CFR 153.430 - Heat transfer systems; general.
Code of Federal Regulations, 2013 CFR
2013-10-01
... 46 Shipping 5 2013-10-01 2013-10-01 false Heat transfer systems; general. 153.430 Section 153.430... Temperature Control Systems § 153.430 Heat transfer systems; general. Each cargo cooling system required by... separated from all other cooling and heating systems; and (c) Allow manual regulation of the system's...
Heat Transfer Study for HTS Power Transfer Cables
NASA Technical Reports Server (NTRS)
Augustynowicz, S.; Fesmire, J.
2002-01-01
Thermal losses are a key factor in the successful application of high temperature superconducting (HTS) power cables. Existing concepts and prototypes rely on the use of multilayer insulation (MLI) systems that are subject to large variations in actual performance. The small space available for the thermal insulation materials makes the application even more difficult because of bending considerations, mechanical loading, and the arrangement between the inner and outer piping. Each of these mechanical variables affects the heat leak rate. These factors of bending and spacing are examined in this study. Furthermore, a maintenance-free insulation system (high vacuum level for 20 years or longer) is a practical requirement. A thermal insulation system simulating a section of a flexible FITS power cable was constructed for test and evaluation on a research cryostat. This paper gives experimental data for the comparison of ideal MLI, MLI on rigid piping, and MLI between flexible piping. A section of insulated flexible piping was tested under cryogenic vacuum conditions including simulated bending and spacers.
Understanding fast heat transfer in the shallow subsurface
NASA Astrophysics Data System (ADS)
Rutten, Martine; Steele-Dunne, Susan; Judge, Jasmeet; van de Giesen, Nick
2010-05-01
Understanding the temperature profile of the shallow subsurface is of great importance for interpreting remote sensing observations and modeling land-atmosphere interaction. Remote sensing observations are translated to surface characteristics, such as vegetation and soil moisture, using radiative transfer schemes that are sensitive to skin temperature estimation. The surface temperature is also a key variable in the heat partitioning of net radiation into sensible, latent and soil heat flux at the interface between land and atmosphere. The temperature profile of the soil is determined by the processes of radiative, convective and conductive heat transfer. Whereas radiative and convective heat transfer are dominant at the soil-air interface, heat transfer within the soil is typically assumed to be governed by conduction and as such is described with a diffusion model. The thermal diffusivity of the soil depends mainly on mineral composition and moisture content and is described in many empirical models. Using temperature data from experiments conducted in Florida (MicroWex 2) and the Netherlands (Monster), we show that diffusion cannot describe heat transfer within approximately the upper ten centimeters of the soil. The heat transfer is significantly faster than would be predicted with a diffusion equation. Diffusivity values, estimated using an inversion approach to the diffusion equation, fall outside the physically reasonable range, which is defined by available soil diffusivity models. The extent of this strongly thermally active layer depends on vegetation conditions, and possibly moisture conditions. We investigate mechanisms that may explain the fast heat transfer in the shallow subsurface. Possible mechanisms include heat transfer by convective heat transfer processes such as latent heat formation and heat transfer due to water percolation. We estimated the size of the heat sink-source at depth and compared these to observations of latent heat and
Heat-transfer simulation in a furnace for steam reformer
Kudo, K.; Taniguchi, H.; Guo, K. . Faculty of Engineering); Katayama, T.; Nagata, T. )
1991-01-01
This paper discusses three-dimensional combined radiative and convective heat-transfer process in a furnace for LPG reforming which is simulated by introducing the radiosity concept into the radiative heat ray method for accurate radiative heat-transfer analysis. Together with an analysis of the chemical reaction in the reactor tubes of the furnace, the heat-transfer simulation gives the three-dimensional profile of the combustion gas temperature in the furnace, the tube-surface heat-flux distribution and the composition of the product gas obtained from the forming. The results obtained are as follows: increasing the jet angle of the heating burner raises the gas temperature and the tube surface heat flux near the burner entrance; the flame shape is the most important factor for deciding the heat flux distribution of the tube surface because the heat transferred by flame radiation is much more than they by convection of the combustion gas.
Turbine disk cavity aerodynamics and heat transfer
NASA Astrophysics Data System (ADS)
Johnson, B. V.; Daniels, W. A.
1992-07-01
Experiments were conducted to define the nature of the aerodynamics and heat transfer for the flow within the disk cavities and blade attachments of a large-scale model, simulating the Space Shuttle Main Engine (SSME) turbopump drive turbines. These experiments of the aerodynamic driving mechanisms explored the following: (1) flow between the main gas path and the disk cavities; (2) coolant flow injected into the disk cavities; (3) coolant density; (4) leakage flows through the seal between blades; and (5) the role that each of these various flows has in determining the adiabatic recovery temperature at all of the critical locations within the cavities. The model and the test apparatus provide close geometrical and aerodynamic simulation of all the two-stage cavity flow regions for the SSME High Pressure Fuel Turbopump and the ability to simulate the sources and sinks for each cavity flow.
Heat and mass transfer in flames
NASA Technical Reports Server (NTRS)
Faeth, G. M.
1986-01-01
Heat- and mass-transfer processes in turbulent diffusion flames are discussed, considering turbulent mixing and the structure of single-phase flames, drop processes in spray flames, and nonluminous and luminous flame radiation. Interactions between turbulence and other phenomena are emphasized, concentrating on past work of the author and his associates. The conserved-scalar formalism, along with the laminar-flamelet approximation, is shown to provide reasonable estimates of the structure of gas flames, with modest levels of empiricism. Extending this approach to spray flames has highlighted the importance of drop/turbulence interactions; e.g., turbulent dispersion of drops, modification of turbulence by drops, etc. Stochastic methods being developed to treat these phenomena are yielding encouraging results.
Submersible pumping system with heat transfer mechanism
Hunt, Daniel Francis Alan; Prenger, F. Coyne; Hill, Dallas D; Jankowski, Todd Andrew
2014-04-15
A submersible pumping system for downhole use in extracting fluids containing hydrocarbons from a well. In one embodiment, the pumping system comprises a rotary induction motor, a motor casing, one or more pump stages, and a cooling system. The rotary induction motor rotates a shaft about a longitudinal axis of rotation. The motor casing houses the rotary induction motor such that the rotary induction motor is held in fluid isolation from the fluid being extracted. The pump stages are attached to the shaft outside of the motor casing, and are configured to impart fluid being extracted from the well with an increased pressure. The cooling system is disposed at least partially within the motor casing, and transfers heat generated by operation of the rotary induction motor out of the motor casing.
HEAT TRANSFER AND TRITIUM PRODUCING SYSTEM
Johnson, E.F.
1962-06-01
This invention related to a circulating lithium-containing blanket system in a neution source hav'ing a magnetic field associated therewith. The blanket serves simultaneously and efficiently as a heat transfer mediunm and as a source of tritium. The blanket is composed of a lithium-6-enriched fused salt selected from the group consisting of lithium nitrite, lithium nitrate, a mixture of said salts, a mixture of each of said salts with lithium oxide, and a mixture of said salts with each other and with lithium oxide. The moderator, which is contained within the blanket in a separate conduit, can be water. A stellarator is one of the neutron sources which can be used in this invention. (AEC)
Low-melting point heat transfer fluid
Cordaro, Joseph G.; Bradshaw, Robert W.
2011-04-12
A low-melting point, heat transfer fluid comprising a mixture of LiNO.sub.3, NaNO.sub.3, KNO.sub.3, NaNO.sub.2 and KNO.sub.2 salts where the Li, Na and K cations are present in amounts of about 20-33.5 mol % Li, about 18.6-40 mol % Na, and about 40-50.3 mol % K and where the nitrate and nitrite anions are present in amounts of about 36-50 mol % NO.sub.3, and about 50-62.5 mol % NO.sub.2. These compositions can have liquidus temperatures between 70.degree. C. and 80.degree. C. for some compositions.
Investigation of heat transfer in porous duct
NASA Astrophysics Data System (ADS)
Athani, Abdulgaphur; Khan, T. M. Yunus
2016-05-01
Investigation of heat transfer in a square porous duct is carried out. The porous medium is sandwiched between inner and outer surface of a square duct. The flow is assumed to follow the Darcy law. The governing momentum and energy equations are non-dimensionalised and then converted to algebraic form of equations using finite element method. Galerkin method is used to transform the partial differential equations into simpler algebraic equations then solved in a iterative manner to arrive at the solution. The results are presented with respect to various geometric and physical parameters such as depth of porous medium, Rayleigh number etc. It is found that the isotherms and the streamlines take symmetrical position along the vertical central line of square duct. The isotherms are penetrated into deeper area at upper half of duct as compared to lower half.
Nanofluids for heat transfer : an engineering approach.
Timofeeva, E. V.; Yu, W.; France, D. M.; Singh, D.; Routbort, J. L.
2011-02-28
An overview of systematic studies that address the complexity of nanofluid systems and advance the understanding of nanoscale contributions to viscosity, thermal conductivity, and cooling efficiency of nanofluids is presented. A nanoparticle suspension is considered as a three-phase system including the solid phase (nanoparticles), the liquid phase (fluid media), and the interfacial phase, which contributes significantly to the system properties because of its extremely high surface-to-volume ratio in nanofluids. The systems engineering approach was applied to nanofluid design resulting in a detailed assessment of various parameters in the multivariable nanofluid systems. The relative importance of nanofluid parameters for heat transfer evaluated in this article allows engineering nanofluids with desired set of properties.
Interface elements for heat transfer analysis
NASA Astrophysics Data System (ADS)
Mason, W. E.
1984-08-01
Interface elements are desirable in finite element heat transfer analyses in situations where dissimilar meshes are to be joined or where contact resistances occur between various parts of a body. In stress codes, such elements are often termed master/slave. A general algorithm for interface elements will be described. The algorithm allows development of interface elements for both two- and three-dimensional applications. Surfaces in contact are automatically determined so that a minimum of input data is required. In addition, the algorithm allows for compatibility in thermal stress calculations with mechanical codes which have sliding interface capabilities. Implementation of the algorithm into the TACO codes will be discussed and examples will be given.
Personalized recommendation based on heat bidirectional transfer
NASA Astrophysics Data System (ADS)
Ma, Wenping; Feng, Xiang; Wang, Shanfeng; Gong, Maoguo
2016-02-01
Personalized recommendation has become an increasing popular research topic, which aims to find future likes and interests based on users' past preferences. Traditional recommendation algorithms pay more attention to forecast accuracy by calculating first-order relevance, while ignore the importance of diversity and novelty that provide comfortable experiences for customers. There are some levels of contradictions between these three metrics, so an algorithm based on bidirectional transfer is proposed in this paper to solve this dilemma. In this paper, we agree that an object that is associated with history records or has been purchased by similar users should be introduced to the specified user and recommendation approach based on heat bidirectional transfer is proposed. Compared with the state-of-the-art approaches based on bipartite network, experiments on two benchmark data sets, Movielens and Netflix, demonstrate that our algorithm has better performance on accuracy, diversity and novelty. Moreover, this method does better in exploiting long-tail commodities and cold-start problem.
Convective heat transfer for fluids passing through aluminum foams
NASA Astrophysics Data System (ADS)
Dyga, Roman; Troniewski, Leon
2015-03-01
This paper analyses the experimental findings within heat transfer when heating up air, water and oil streams which are passed through a duct with internal structural packing elements in the form of metal foams. Three types of aluminum foams with different cell sizes, porosity specifications and thermal conductivities were used in the study. The test data were collected and they made it possible to establish the effect of the foam geometry, properties of fluids and flow hydrodynamic conditions on the convective heat transfer process from the heating surface to the fluid flowing by (wetting) that surface. The foam was found to be involved in heat transfer to a limited extent only. Heat is predominantly transferred directly from the duct wall to a fluid, and intensity of convective heat transfer is controlled by the wall effects. The influence of foam structural parameters, like cell size and/or porosity, becomes more clearly apparent under laminar flow conditions.
NASA Astrophysics Data System (ADS)
Kılıç, Bayram; İpek, Osman
2016-06-01
In this study, heat transfer rate and effectiveness of corrugated plate heat exchangers having different chevron angles were investigated experimentally. Chevron angles of plate heat exchangers are β = 30° and β = 60°. For this purpose, experimentally heating system used plate heat exchanger was designed and constructed. Thermodynamic analysis of corrugated plate heat exchangers having different chevron angles were carried out. The heat transfer rate and effectiveness values are calculated. The experimental results are shown that heat transfer rate and effectiveness values for β = 60° is higher than that of the other. Obtained experimental results were graphically presented.
Turbine stage aerodynamics and heat transfer prediction
NASA Technical Reports Server (NTRS)
Griffin, Lisa W.; Mcconnaughey, H. V.
1989-01-01
A numerical study of the aerodynamic and thermal environment associated with axial turbine stages is presented. Computations were performed using a modification of the unsteady NASA Ames viscous code, ROTOR1, and an improved version of the NASA Lewis steady inviscid cascade system MERIDL-TSONIC coupled with boundary layer codes BLAYER and STAN5. Two different turbine stages were analyzed: the first stage of the United Technologies Research Center Large Scale Rotating Rig (LSRR) and the first stage of the Space Shuttle Main Engine (SSME) high pressure fuel turbopump turbine. The time-averaged airfoil midspan pressure and heat transfer profiles were predicted for numerous thermal boundary conditions including adiabatic wall, prescribed surface temperature, and prescribed heat flux. Computed solutions are compared with each other and with experimental data in the case of the LSRR calculations. Modified ROTOR1 predictions of unsteady pressure envelopes and instantaneous contour plots are also presented for the SSME geometry. Relative merits of the two computational approaches are discussed.
TACO: a finite element heat transfer code
Mason, W.E. Jr.
1980-02-01
TACO is a two-dimensional implicit finite element code for heat transfer analysis. It can perform both linear and nonlinear analyses and can be used to solve either transient or steady state problems. Either plane or axisymmetric geometries can be analyzed. TACO has the capability to handle time or temperature dependent material properties and materials may be either isotropic or orthotropic. A variety of time and temperature dependent loadings and boundary conditions are available including temperature, flux, convection, and radiation boundary conditions and internal heat generation. Additionally, TACO has some specialized features such as internal surface conditions (e.g., contact resistance), bulk nodes, enclosure radiation with view factor calculations, and chemical reactive kinetics. A user subprogram feature allows for any type of functional representation of any independent variable. A bandwidth and profile minimization option is also available in the code. Graphical representation of data generated by TACO is provided by a companion post-processor named POSTACO. The theory on which TACO is based is outlined, the capabilities of the code are explained, the input data required to perform an analysis with TACO are described. Some simple examples are provided to illustrate the use of the code.
NASA Technical Reports Server (NTRS)
Fink, Richard
2015-01-01
The increasing use of power electronics, such as high-current semiconductor devices and modules, within space vehicles is driving the need to develop specialty thermal management materials in both the packaging of these discrete devices and the packaging of modules consisting of these device arrays. Developed by Applied Nanotech, Inc. (ANI), CarbAl heat transfer material is uniquely characterized by its low density, high thermal diffusivity, and high thermal conductivity. Its coefficient of thermal expansion (CTE) is similar to most power electronic materials, making it an effective base plate substrate for state-of-the-art silicon carbide (SiC) super junction transistors. The material currently is being used to optimize hybrid vehicle inverter packaging. Adapting CarbAl-based substrates to space applications was a major focus of the SBIR project work. In Phase I, ANI completed modeling and experimentation to validate its deployment in a space environment. Key parameters related to cryogenic temperature scaling of CTE, thermal conductivity, and mechanical strength. In Phase II, the company concentrated on improving heat sinks and thermally conductive circuit boards for power electronic applications.
Sensitivity Analysis of the Gap Heat Transfer Model in BISON.
Swiler, Laura Painton; Schmidt, Rodney C.; Williamson, Richard; Perez, Danielle
2014-10-01
This report summarizes the result of a NEAMS project focused on sensitivity analysis of the heat transfer model in the gap between the fuel rod and the cladding used in the BISON fuel performance code of Idaho National Laboratory. Using the gap heat transfer models in BISON, the sensitivity of the modeling parameters and the associated responses is investigated. The study results in a quantitative assessment of the role of various parameters in the analysis of gap heat transfer in nuclear fuel.
Heat Transfer in Regions of Separated and Reattached Flows
NASA Technical Reports Server (NTRS)
Crawford, Davis H; Rumsey, Charles B
1957-01-01
Past experimental work has indicated that separated flow can greatly increase the heat transfer to a surface; whereas, some theoretical studies have indicated a possible decrease. Recent investigations have helped to clarify the effects of separation on heat transfer and have indicated a method of reducing separation. This paper considers the results of some of these investigations and shows the heat transfer in regions of separation and reattachment for a few specific shapes. These results show that the heat transfer in a separated region is strongly affected by the extent of separation, the location of the reattachment point, and the location of transition along the separated boundary.
Nonlinear Transient Problems Using Structure Compatible Heat Transfer Code
NASA Technical Reports Server (NTRS)
Hou, Gene
2000-01-01
The report documents the recent effort to enhance a transient linear heat transfer code so as to solve nonlinear problems. The linear heat transfer code was originally developed by Dr. Kim Bey of NASA Largely and called the Structure-Compatible Heat Transfer (SCHT) code. The report includes four parts. The first part outlines the formulation of the heat transfer problem of concern. The second and the third parts give detailed procedures to construct the nonlinear finite element equations and the required Jacobian matrices for the nonlinear iterative method, Newton-Raphson method. The final part summarizes the results of the numerical experiments on the newly enhanced SCHT code.
Heat transfer coefficient in serpentine coolant passage for CCDTL
Leslie, P.; Wood, R.; Sigler, F.; Shapiro, A.; Rendon, A.
1998-12-31
A series of heat transfer experiments were conducted to refine the cooling passage design in the drift tubes of a coupled cavity drift tube linac (CCDTL). The experimental data were then compared to numerical models to derive relationships between heat transfer rates, Reynold`s number, and Prandtl number, over a range of flow rates. Data reduction consisted of axisymmetric finite element modeling where the heat transfer coefficients were modified to match the experimental data. Unfortunately, the derived relationship is valid only for this specific geometry of the test drift tube. Fortunately, the heat transfer rates were much better (approximately 2.5 times) than expected.
Heat Transfer Variation on Protuberances and Surface Roughness Elements
NASA Technical Reports Server (NTRS)
Henry, Robert C.; Hansman, R. John, Jr.; Breuer, Kenneth S.
1995-01-01
In order to determine the effect of surface irregularities on local convective heat transfer, the variation in heat transfer coefficients on small (2-6 mm diam) hemispherical roughness elements on a flat plate has been studied in a wind funnel using IR techniques. Heat transfer enhancement was observed to vary over the roughness elements with the maximum heat transfer on the upstream face. This heat transfer enhancement increased strongly with roughness size and velocity when there was a laminar boundary layer on the plate. For a turbulent boundary layer, the heat transfer enhancement was relatively constant with velocity, but did increase with element size. When multiple roughness elements were studied, no influence of adjacent roughness elements on heat transfer was observed if the roughness separation was greater than approximately one roughness element radius. As roughness separation was reduced, less variation in heat transfer was observed on the downstream elements. Implications of the observed roughness enhanced heat transfer on ice accretion modeling are discussed.
Heat transfer coefficients for drying in pulsating flows
Fraenkel, S.L.
1998-05-01
Pulsating flows generated by a Rijke type combustor are studied for drying of grains and food particles. It is assumed that the velocity fluctuations are the main factor in the enhancement of the drying process. The heat transfer coefficients for drying in vibrating beds are utilized to estimate the heat transfer coefficients of fixed beds in pulsating and permeating flows and are compared to the steady flow heat transfer coefficients obtained for solid porous bodies, after perturbing the main flow. The cases considered are compared to the convective heat transfer coefficients employed in non-pulsating drying.
Boiling heat transfer of refrigerant R-21 in upward flow in plate-fin heat exchanger
NASA Astrophysics Data System (ADS)
Kuznetsov, V. V.; Shamirzaev, A. S.
2015-11-01
The article presents the results of experimental investigation of boiling heat transfer of refrigerant R-21 in upward flow in a vertical plate-fin heat exchanger with transverse size of the channels that is smaller than the capillary constant. The heat transfer coefficients obtained in ranges of small mass velocities and low heat fluxes, which are typical of the industry, have been poorly studied yet. The characteristic patterns of the upward liquid-vapor flow in the heat exchanger channels and the regions of their existence are detected. The obtained data show a weak dependence of heat transfer coefficient on equilibrium vapor quality, mass flow rate, and heat flux density and do not correspond to calculations by the known heat transfer models. A possible reason for this behavior is a decisive influence of evaporation of thin liquid films on the heat transfer at low heat flux.
Analysis for radiative heat transfer in a circulating fluidized bed
Steward, F.R.; Couturier, M.F.; Poolpol, S.
1995-12-31
The radiative heat transfer from the particles within a circulating fluidized bed has been determined for a number of different assumptions. Based on temperature profiles measured in an operating circulating fluidized bed burning coal, a procedure for predicting the radiative transfer from the solid particles to a cold wall is recommended. The radiative transfer from the solid particles to a cold wall makes up approximately 50% of the total heat transfer to the wall in a circulating fluidized bed combustor.
Inter-phase heat transfer and energy coupling in turbulent dispersed multiphase flows
NASA Astrophysics Data System (ADS)
Ling, Y.; Balachandar, S.; Parmar, M.
2016-03-01
The present paper addresses important fundamental issues of inter-phase heat transfer and energy coupling in turbulent dispersed multiphase flows through scaling analysis. In typical point-particle or two-fluid approaches, the fluid motion and convective heat transfer at the particle scale are not resolved and the momentum and energy coupling between fluid and particles are provided by proper closure models. By examining the kinetic energy transfer due to the coupling forces from the macroscale to microscale fluid motion, closure models are obtained for the contributions of the coupling forces to the energy coupling. Due to the inviscid origin of the added-mass force, its contribution to the microscale kinetic energy does not contribute to dissipative transfer to fluid internal energy as was done by the quasi-steady force. Time scale analysis shows that when the particle is larger than a critical diameter, the diffusive-unsteady kernel decays at a time scale that is smaller than the Kolmogorov time scale. As a result, the computationally costly Basset-like integral form of diffusive-unsteady heat transfer can be simplified to a non-integral form. Conventionally, the fluid-to-particle volumetric heat capacity ratio is used to evaluate the relative importance of the unsteady heat transfer to the energy balance of the particles. Therefore, for gas-particle flows, where the fluid-to-particle volumetric heat capacity ratio is small, unsteady heat transfer is usually ignored. However, the present scaling analysis shows that for small fluid-to-particle volumetric heat capacity ratio, the importance of the unsteady heat transfer actually depends on the ratio between the particle size and the Kolmogorov scale. Furthermore, the particle mass loading multiplied by the heat capacity ratio is usually used to estimate the importance of the thermal two-way coupling effect. Through scaling argument, improved estimates are established for the energy coupling parameters of each
Banerjee, S.; Hassan, Y.A.
1995-09-01
Condensation in the presence of noncondensible gases plays an important role in the nuclear industry. The RELAP5/MOD3 thermal hydraulic code was used to study the ability of the code to predict this phenomenon. Two separate effects experiments were simulated using this code. These were the Massachusetts Institute of Technology`s (MIT) Pressurizer Experiment, the MIT Single Tube Experiment. A new iterative approach to calculate the interface temperature and the degraded heat transfer coefficient was developed and implemented in the RELAP5/MOD3 thermal hydraulic code. This model employs the heat transfer simultaneously. This model was found to perform much better than the reduction factor approach. The calculations using the new model were found to be in much better agreement with the experimental values.
Neutron behavior, reactor control, and reactor heat transfer. Volume four
Not Available
1986-01-01
Volume four covers neutron behavior (neutron absorption, how big are nuclei, neutron slowing down, neutron losses, the self-sustaining reactor), reactor control (what is controlled in a reactor, controlling neutron population, is it easy to control a reactor, range of reactor control, what happens when the fuel burns up, controlling a PWR, controlling a BWR, inherent safety of reactors), and reactor heat transfer (heat generation in a nuclear reactor, how is heat removed from a reactor core, heat transfer rate, heat transfer properties of the reactor coolant).
Methods for calculating conjugate problems of heat transfer
NASA Astrophysics Data System (ADS)
Kalinin, E. K.; Dreitser, G. A.; Kostiuk, V. V.; Berlin, I. I.
Methods are examined for calculating various conjugate problems of heat transfer in channels and closed vessels in cases of single-phase and two-phase flow in steady and unsteady conditions. The single-phase-flow studies involve the investigation of gaseous and liquid heat-carriers in pipes, annular and plane channels, and pipe bundles in cases of cooling and heating. General relationships are presented for heat transfer in cases of film, transition, and nucleate boiling, as well as for boiling crises. Attention is given to methods for analyzing the filling and cooling of conduits and tanks by cryogenic liquids; and ways to intensify heat transfer in these conditions are examined.
ERIC Educational Resources Information Center
Schaefle, Scott; Smaby, Marlowe H.; Packman, Jill; Maddux, Cleborne D.
2007-01-01
The purposes of the present study were to determine if (a) students trained to demonstrate specific skills learn these skills and transfer them to actual counseling sessions; (b) mastery of counseling skills differs by students' adherence to one of four general counseling theories; (c) mastery of counseling skills is related to counseling goal…
Sandwich heating film boiling heat transfer research in narrow rectangle channel
NASA Astrophysics Data System (ADS)
Wang, Z. H.; Ni, M. J.
2010-03-01
The narrow rectangle channel heat transfer technique is a new developing heat transfer technique in recent years. In the narrow rectangle channel, film boiling is an important two-phase flow heat transfer process in many engineering application, including steam generator, nuclear reactor and engineering metallurgy. As the temperature of droplet, steam and wall are decided by forced convection heat transfer between the steam and the wall, the droplet and the wall, the steam and the droplet and radiation heat transfer process, which makes heat transfer mechanism of film boiling be difficultly interpretative. Film boiling in narrow rectangle channel is analyzed in the paper, investigating the influence of all kinds of heat transfer processes on film boiling. A rectangle channel film boiling model has been built up using thermodynamic non-equilibrium model.
Heat transfer modelling of spherical particles subject to heating in a fluidized bed
Dincer, I.; Kilic, Y.A.; Kahveci, N.
1996-09-01
This paper presents an analytical model for analyzing transient heat transfer between a brick particle and air flow during heating in a fluidized bed combustor. Both experimental and theoretical studies were carried out. The experimental investigation provided the temperature distributions at the centers of the spherical particles during heating. These data were presented in the dimensionless form and were compared with the results of the present analytical model. The theoretical investigation included two cases: e.g. Case 1 considered that the surface heat transfer coefficient is only the convection heat transfer coefficient; Case 2 also considered that the surface heat transfer coefficient is the sum of the convection and radiation heat transfer coefficients. Better agreement was found between the experimental data and the theoretical Case 2. The results of this study show that there is a dominant effect of the radiation heat transfer on the temperature distribution.
Wake Modes and Heat Transfer from Rotationally Oscillating Cylinder
NASA Astrophysics Data System (ADS)
Sellappan, Prabu; Pottebaum, Tait
2012-11-01
Wake formation is an important problem in engineering due to its effect on phenomena such as vortex induced vibrations and heat transfer. While prior work has focused on the wake formation due to vortex shedding from stationary and oscillating cylinders, limited information is available on the relationship between wake modes and heat transfer from rotationally oscillating cylinders. Experiments were carried out at Re=150 and 750, using an electrically heated cylinder, in a water tunnel for oscillation frequencies from 0.67 to 3.5 times the natural shedding frequency and peak-to-peak oscillation amplitudes up to 320. DPIV was used to identify and map wake modes to various regions of the parameter space. Temperature data from a thermocouple embedded in the cylinder was used to calculate heat transfer rates. Correlation between heat transfer enhancement and certain wake mode regions were observed in the parameter space. The relationship between wake formation and heat transfer enhancement will be described.
Heat transfer research on supercritical water flow upward in tube
Li, H. B.; Yang, J.; Gu, H. Y.; Zhao, M.; Lu, D. H.; Zhang, J. M.; Wang, F.; Zhang, Y.
2012-07-01
The experimental research of heat transfer on supercritical water has been carried out on the supercritical water multipurpose test loop with a 7.6 mm upright tube. The experimental data of heat transfer is obtained. The experimental results of thermal-hydraulic parameters on flow and heat transfer of supercritical water show that: Heat transfer enhancement occurs when the fluid temperature reaches pseudo-critical point with low mass flow velocity, and peters out when the mass flow velocity increases. The heat transfer coefficient and Nusselt number decrease with the heat flux or system pressure increases, and increase with the increasing of mass flow velocity. The wall temperature increases when the mass flow velocity decreases or the system pressure increases. (authors)
Generator-absorber-heat exchange heat transfer apparatus and method and use thereof in a heat pump
Phillips, Benjamin A.; Zawacki, Thomas S.
1996-12-03
Numerous embodiments and related methods for generator-absorber heat exchange (GAX) are disclosed, particularly for absorption heat pump systems. Such embodiments and related methods use the working solution of the absorption system for the heat transfer medium. A combination of weak and rich liquor working solution is used as the heat transfer medium.
Generator-absorber-heat exchange heat transfer apparatus and method and use thereof in a heat pump
Phillips, Benjamin A.; Zawacki, Thomas S.; Marsala, Joseph
1994-11-29
Numerous embodiments and related methods for generator-absorber heat exchange (GAX) are disclosed, particularly for absorption heat pump systems. Such embodiments and related methods use the working solution of the absorption system for the heat transfer medium.
Investigation of heat transfer with film cooling to a flat plate in a shock tube
NASA Astrophysics Data System (ADS)
Jurgelewicz, Scott A.
1989-12-01
The heat transfer occurring through turbulent boundary layers in modern gas turbines is not well understood. The heat transferred to a flat plate though a turbulent boundary layer presents many similarities without the complex flow patterns. The gas used in this study was air. The flow behind a passing shock wave in a shock tube was used to simulate the high temperature ratio flows found in gas turbines. Highly responsive heat flux gages were used to measure the temperature history of a flat plate exposed to the flow. High speed digital recorders were used to sample and store the information. Heat transfer rates were determined from temperature history using a computer program and a quadrature method. The temperature history was numerically averaged to filter out noise effects before it was used to calculate the heat flux. It was found that low shock Mach numbers produced measured heat flux rates that were predictable by theory. At higher Mach numbers the rounded leading edge of the plate produced reflections that increased the measured heat flux as the Mach number increased; but theory, dependent on incident shock Mach number, underpredicted these actual values. Film cooling flows were then studied under the same flow conditions. Ratios of heat transfer coefficients with blowing ratios of approximately two to three produced the best agreement with correlations. The effects of free stream turbulence on the heat flux with film cooling were also briefly studied.
The heat transfer coefficients of the heating surface of 300 MWe CFB boiler
NASA Astrophysics Data System (ADS)
Wu, Haibo; Zhang, Man; Lu, Qinggang; Sun, Yunkai
2012-08-01
A study of the heat transfer about the heating surface of three commercial 300 MWe CFB boilers was conducted in this work. The heat transfer coefficients of the platen heating surface, the external heat exchanger (EHE) and cyclone separator were calculated according to the relative operation data at different boiler loads. Moreover, the heat transfer coefficient of the waterwall was calculated by heat balance of the hot circuit of the CFB boiler. With the boiler capacity increasing, the heat transfer coefficients of these heating surface increases, and the heat transfer coefficient of the water wall is higher than that of the platen heating surface. The heat transfer coefficient of the EHE is the highest in high boiler load, the heat transfer coefficient of the cyclone separator is the lowest. Because the fired coal is different from the design coal in No.1 boiler, the ash content of the fired coal is much lower than that of the design coal. The heat transfer coefficients which calculated with the operation data are lower than the previous design value and that is the reason why the bed temperature is rather high during the boiler operation in No.1 boiler.
Double tube heat exchanger with novel enhancement: part II—single phase convective heat transfer
NASA Astrophysics Data System (ADS)
Tiruselvam, R.; Chin, W. M.; Raghavan, Vijay R.
2012-08-01
The study is conducted to evaluate the heat transfer characteristics of two new and versatile enhancement configurations in a double tube heat exchanger annulus. The novelty is that they are usable in single phase forced convection, evaporation and condensation. Heat transfer coefficients are determined by the Wilson Plot technique in laminar and turbulent flow and correlations are proposed for Nusselt numbers. Comparisons are then made between heat transfer and flow friction.
A structured surface for high performance evaporative heat transfer
NASA Technical Reports Server (NTRS)
Saaski, E. W.; Hamasaki, R. H.
1977-01-01
An evaporative surface is described for heat pipes and other two-phase heat transfer applications that consists of a hybrid composition of V-grooves and capillary wicking. Characteristics of the surface include both a high heat transfer coefficient and high heat flux capability relative to conventional open faced screw thread surfaces. With a groove density of 12.6/cm and ammonia working fluid, heat transfer coefficients in the range of 1 to 2 W/sq cm K have been measured, along with maximum heat flux densities in excess of 20 W/sq cm. A peak heat transfer coefficient in excess of 2.3 W/sq cm K at 20 W/sq cm was measured with a 37.8/cm hybrid surface.
Study of a high performance evaporative heat transfer surface
NASA Technical Reports Server (NTRS)
Saaski, E. W.; Hamasaki, R. H.
1977-01-01
An evaporative surface is described for heat pipes and other two-phase heat transfer applications that consists of a hybrid composition of V-grooves and capillary wicking. Characteristics of the surface include both a high heat transfer coefficient and high heat flux capability relative to conventional open-faced screw thread surfaces. With a groove density of 12.6 cm/1 and ammonia working fluid, heat transfer coefficients in the range of 1 to 2 W/sq cm have been measured along with maximum heat flux densities in excess of 20 W/sq cm. A peak heat transfer coefficient in excess of 2.3 W/sq cm was measured with a 37.8 cm/1 hybrid surface.
Capillary Pumped Heat Transfer (CHT) Experiment
NASA Technical Reports Server (NTRS)
Hallinan, Kevin P.; Allen, J. S.
1998-01-01
The operation of Capillary Pumped Loops (CPL's) in low gravity has generally been unable to match ground-based performance. The reason for this poorer performance has been elusive. In order to investigate the behavior of a CPL in low-gravity, an idealized, glass CPL experiment was constructed. This experiment, known as the Capillary-driven Heat Transfer (CHT) experiment, was flown on board the Space Shuttle Columbia in July 1997 during the Microgravity Science Laboratory mission. During the conduct of the CHT experiment an unexpected failure mode was observed. This failure mode was a result of liquid collecting and then eventually bridging the vapor return line. With the vapor return line blocked, the condensate was unable to return to the evaporator and dry-out subsequently followed. The mechanism for this collection and bridging has been associated with long wavelength instabilities of the liquid film forming in the vapor return line. Analysis has shown that vapor line blockage in present generation CPL devices is inevitable. Additionally, previous low-gravity CPL tests have reported the presence of relatively low frequency pressure oscillations during erratic system performance. Analysis reveals that these pressure oscillations are in part a result of long wavelength instabilities present in the evaporator pores, which likewise lead to liquid bridging and vapor entrapment in the porous media. Subsequent evaporation to the trapped vapor increases the vapor pressure. Eventually the vapor pressure causes ejection of the bridged liquid. Recoil stresses depress the meniscus, the vapor pressure rapidly increases, and the heated surface cools. The process then repeats with regularity.
Experimental analysis of heat transfer mechanism in MCFC
Sugiura, K.; Naruse, I.; Ohtake, K.
1998-07-01
Characteristics of heat transfer in Molten Carbonate Fuel Cells(MCFC) installed with offset-type fins are studied by using a fuel cell model consisting of electrodes, a perforated plate and a corrugated current collector. In this study the effect of several kinds of reacting gas on heat transfer characteristics is elucidated by measuring gas and surface temperatures, gas species composition, cell components and vertical heat flux. As a result, Wieting's equation to evaluate heat transfer characteristics in heat exchangers is not appropriate to the MCFC since Reynolds number in operating the MCFC is far less than the applicable range of the equation. Most of the vertical heat flux is controlled by heat conduction in the cell components. The convective heat transfer coefficient depends on kinds of gas species rather than the gas flow rate. Thermal properties affect the convective heat transfer coefficient. Especially, the vertical heat flux increases with an increase of H{sub 2} concentration. The obtained fundamental results can elucidate phenomena of heat transfer in practical MCFC appropriately.
Heat transfer of suspended carbon nanotube yarn to gases
NASA Astrophysics Data System (ADS)
Wada, Yukiko; Kita, Koji; Takei, Kuniharu; Arie, Takayuki; Akita, Seiji
2016-08-01
We investigate the pressure dependence of heat transfer to ambient gases for a suspended carbon nanotube yarn. The heat transport of the yarn including the heat exchange with surrounding gases is investigated using a simple one-dimensional heat transport model under Joule heating of the yarn. It is revealed that the effective diameter of the yarn for heat exchange is much smaller than the geometrical diameter of the yarn. This smaller effective diameter for heat exchange should contribute to realizing higher sensitivity and sensing over a wider range of pressures for heat-exchange-type vacuum gauges and flow sensors.
Dual circuit embossed sheet heat transfer panel
Morgan, Grover D.
1984-01-01
A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.
Dual circuit embossed sheet heat transfer panel
Morgan, G.D.
1984-02-21
A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet. 6 figs.
Investigation of heat transfer efficiency in coplanar channels
NASA Astrophysics Data System (ADS)
Pelevin, F. V.; Yaroslavtsev, N. L.; Vikulin, A. V.; Orlin, S. A.; Ponomarev, A. V.
2015-03-01
Achieving more efficient heat transfer in heat-transfer devices is a topical problem. Heat transfer and pressure drop in paths containing coplanar channels of different shapes are experimentally studied in this work. It is found that the mutual crossing angles of coplanar channels, finning ratio, and the dimensions of coplanar channels are the main parameters influencing heat transfer enhancement. The best effect from using coplanar channels is achieved at the values of Reynolds number Re = 103-104. The coefficient of heat transfer in coplanar channels can be increased by a factor of 3-10 as compared with that for a smooth channel. The pressure drop coefficient ξ increases with increasing the total mutual channel crossing angle. It is found that heat transfer in flat paths with coplanar channels becomes less efficient with decreasing the coplanar channel's equivalent hydraulic diameter to 0.5-1.0 mm, whereas more efficient heat transfer is obtained by fitting these channels with flow microturbulizers. It is shown that increasing the finning height in cylindrical paths with coplanar channels has no effect on vortex formation in them; however, it results in a higher finning ratio, due to which more efficient heat transfer is obtained
7 CFR 3201.54 - Heat transfer fluids.
Code of Federal Regulations, 2013 CFR
2013-01-01
... Designated Items § 3201.54 Heat transfer fluids. (a) Definition. Products with high thermal capacities used... for use in HVAC applications, internal combustion engines, personal cooling devices, thermal energy... 7 Agriculture 15 2013-01-01 2013-01-01 false Heat transfer fluids. 3201.54 Section...
7 CFR 3201.54 - Heat transfer fluids.
Code of Federal Regulations, 2012 CFR
2012-01-01
... Designated Items § 3201.54 Heat transfer fluids. (a) Definition. Products with high thermal capacities used... for use in HVAC applications, internal combustion engines, personal cooling devices, thermal energy... 7 Agriculture 15 2012-01-01 2012-01-01 false Heat transfer fluids. 3201.54 Section...
7 CFR 2902.54 - Heat transfer fluids.
Code of Federal Regulations, 2011 CFR
2011-01-01
... Items § 2902.54 Heat transfer fluids. (a) Definition. Products with high thermal capacities used to... HVAC applications, internal combustion engines, personal cooling devices, thermal energy storage, or... 7 Agriculture 15 2011-01-01 2011-01-01 false Heat transfer fluids. 2902.54 Section...
Improving Heat Transfer Performance of Printed Circuit Boards
NASA Technical Reports Server (NTRS)
Schatzel, Donald V.
2009-01-01
This paper will explore the ability of printed circuit boards laminated with a Carbon Core Laminate to transfer heat vs. standard printed circuit boards that use only thick layers of copper. The paper will compare the differences in heat transfer performance of printed circuit boards with and without CCL.
Heat transfer in banks of tubes in crossflow
Zukauskas, A.; Ulinskas, R.
1988-01-01
This volume examines heat transfer, resistance, and characteristics of flow across banks of smooth, rough, and finned tubes over a wide range of parameters. The studies comprising the work are complemented by additional material on local and average heat transfer for in-line and staggered banks of tubes, and determination of optimal pitch, roughness parameters, finning, and effectiveness.
Mixed convection heat transfer in concave and convex channels
Moukalled, F.; Doughan, A.; Acharya, S.
1997-07-01
Mixed convection heat transfer studies in the literature have been primarily confined to pipe and rectangular channel geometry's. In some applications, however, heat transfer in curved channels may be of interest (e.g., nozzle and diffuser shaped passages in HVAC systems, fume hoods, chimneys, bell-shaped or dome-shaped chemical reactors, etc.). A numerical investigation of laminar mixed convection heat transfer of air in concave and convex channels is presented. Six different channel aspects ratios (R/L = 1.04, 1.25, 2.5, 5, 10, and {infinity}) and five different values of Gr/Re{sup 2} (Gr/Re{sup 2} = 0, 0.1, 1, 3, 5) are considered. Results are displayed in terms of streamline and isotherm plots, velocity and temperature profiles, and local and average Nusselt number estimates. Numerical predictions reveal that compared to straight channels of equal height, concave channels of low aspect ratio have lower heat transfer at relatively low values of Gr/Re{sup 2} and higher heat transfer at high values of Gr/Re{sup 2}. When compared to straight channels of equal heated length, concave channels are always found to have lower heat transfer and for all values of Gr/Re{sup 2}. On the other hand, predictions for convex channels revealed enhancement in heat transfer compared to straight channels of equal height and/or equal heated length for all values of Gr/Re{sup 2}.
Micro-scale drop dynamics for heat transfer enhancement
NASA Astrophysics Data System (ADS)
Francois, Marianne; Shyy, Wei
2002-05-01
With rapid advances in micro-device fabrication, computational techniques, and diagnostic tools, there is a significant interest in applying micro-scale fluid dynamics and heat transfer to flow control, flight vehicle protection, and thermal management. Utilizing energy transfer associated with phase change, multiphase systems offer many new opportunities. To elucidate the main scientific issues and technical implications, recent research addressing the interplay between capillarity, moving boundaries, fluid dynamics, heat transfer, and phase change of micro-scale multiphase systems is reviewed. The parametric variations in contact angle, surface tension, impact velocity, and liquid viscosity related to drop impingement and heat transfer are discussed.
Proceedings of the 33rd national heat transfer conference NHTC'99
Jensen, M.K.; Di Marzo, M.
1999-07-01
The papers in this conference were divided into the following sections: Radiation Heat Transfer in Fires; Computational Fluid Dynamics Methods in Two-Phase Flow; Heat Transfer in Microchannels; Thin Film Heat Transfer; Thermal Design of Electronics; Enhanced Heat Transfer I; Porous Media Convection; Contact Resistance Heat Transfer; Materials Processing in Solidification and Crystal Growth; Fundamentals of Combustion; Challenging Modeling Aspects of Radiative Transfer; Fundamentals of Microscale Transport; Laser Processing and Diagnostics for Manufacturing and Materials Processing; Experimental Studies of Multiphase Flow; Enhanced Heat Transfer II; Heat and Mass Transfer in Porous Media; Heat Transfer in Turbomachinery and Gas Turbine Systems; Conduction Heat Transfer; General Papers; Open Forum on Combustion; Combustion and Instrumentation and Diagnostics I; Radiative Heat Transfer and Interactions in Participating and Nonparticipating Media; Applications of Computational Heat Transfer; Heat Transfer and Fluid Aspects of Heat Exchangers; Two-Phase Flow and Heat Transfer Phenomena; Fundamentals of Natural and Mixed Convection Heat Transfer I; Fundamental of Natural and Mixed Convection Heat Transfer II; Combustion and Instrumentation and Diagnostics II; Computational Methods for Multidimensional Radiative Transfer; Process Heat Transfer; Advances in Computational Heat and Mass Transfer; Numerical Methods for Porous Media; Transport Phenomena in Manufacturing and Materials Processing; Practical Combustion; Melting and Solidification Heat Transfer; Transients in Dynamics of Two-Phase Flow; Basic Aspects of Two-Phase Flow; Turbulent Heat Transfer; Convective Heat Transfer in Electronics; Thermal Problems in Radioactive and Mixed Waste Management; and Transport Phenomena in Oscillatory Flows. Separate abstracts were prepared for most papers in this conference.
Flow and heat transfer characteristics of orthogonally rotating channel
NASA Astrophysics Data System (ADS)
Tamura, Hiroshi; Ishigaki, Hiroshi
1991-12-01
Numerical analysis was conducted to predict the centripetal buoyant effect on flow and heat transfer characteristics in a channel rotating about a perpendicular axis. The conditions were assumed to be laminar, fully developed, and uniform heat flux. Calculation were conducted both for radially outward flow from the rotating axis and radially inward flow. The calculated results indicated that for radially outward flow buoyancy decreases the suction side friction and heat transfer while increasing pressure side friction and heat transfer. This trends were reversed for radially inward flow.
Laminar flow heat transfer downstream from U-bends
NASA Astrophysics Data System (ADS)
Abdelmessih, Amanie Nassif
1987-05-01
The laminar flow heat transfer downstream from the unheated, vertical bends in horizontal U-tubes with electrically heated straight tube sections was investigated. For each test section, local axial and peripheral wall temperatures were measured and the local peripheral heat transfer coefficients at the various locations were calculated. The investigation permitted a better understanding of the interaction of the primary, secondary and tertiary flow patterns, i.e., the combination of forced and natural convection with the centrifugal effects. Also, a correlation was developed, which predicts the heat transfer coefficient downstream from an unheated U-bend, and which can be extended to straight tubes.
Experimental study of heat transfer to falling liquid films
NASA Astrophysics Data System (ADS)
Fagerholm, N. E.; Kivioja, K.; Ghazanfari, A. R.; Jaervinen, E.
1985-12-01
This project was initiated in order to obtain more knowledge about thermal design of falling film heat exchangers and to find methods to improve heat transfer in film flow. A short literature survey of film flow characteristics and heat transfer is presented. An experimental apparatus designed and built for studying falling film evaporation is described. The first experiments were made with smooth Cu tube 25/22 mm and refrigerant R114 as evaporating liquid. A significant amount of droplet entrainment was observed during the tests. The measured average heat transfer coefficient varied from 1000 to 1800 W/m K when Re=1300 to 11000 respectively and when the transfer mode is surface evaporation. This could be predicted accurately with the experimental correlation of Chun and Seban. When nucleate boiling is dominant the heat transfer could be predicted well with pool boiling correlation of VDI-84.
Measurement of airfoil heat transfer coefficients on a turbine stage
NASA Astrophysics Data System (ADS)
Dring, Robert P.; Blair, Michael F.; Joslyn, H. David
1986-10-01
The Primary basis for heat transfer analysis of turbine airfoils is experimental data obtained in linear cascades. These data were very valuable in identifying the major heat transfer and fluid flow features of a turbine airfoil. The first program objective is to obtain a detailed set of heat transfer coefficients along the midspan of a stator and a rotor in a rotating turbine stage. The data are to be compared to some standard analysis of blade boundary layer heat transfer which is in use today. A second program objective is to obtain a detailed set of heat transfer coefficients along the midspan of a stator located in the wake of an upstream turbine stage.
Quantitative Global Heat Transfer in a Mach-6 Quiet Tunnel
NASA Technical Reports Server (NTRS)
Sullivan, John P.; Schneider, Steven P.; Liu, Tianshu; Rubal, Justin; Ward, Chris; Dussling, Joseph; Rice, Cody; Foley, Ryan; Cai, Zeimin; Wang, Bo; Woodiga, Sudesh
2012-01-01
This project developed quantitative methods for obtaining heat transfer from temperature sensitive paint (TSP) measurements in the Mach-6 quiet tunnel at Purdue, which is a Ludwieg tube with a downstream valve, moderately-short flow duration and low levels of heat transfer. Previous difficulties with inferring heat transfer from TSP in the Mach-6 quiet tunnel were traced to (1) the large transient heat transfer that occurs during the unusually long tunnel startup and shutdown, (2) the non-uniform thickness of the insulating coating, (3) inconsistencies and imperfections in the painting process and (4) the low levels of heat transfer observed on slender models at typical stagnation temperatures near 430K. Repeated measurements were conducted on 7 degree-half-angle sharp circular cones at zero angle of attack in order to evaluate the techniques, isolate the problems and identify solutions. An attempt at developing a two-color TSP method is also summarized.
Heat transfer between immiscible liquids enhanced by gas bubbling
NASA Astrophysics Data System (ADS)
Greene, G. A.; Schwarz, C. E.; Klages, J.; Klein, J.
1982-08-01
The phenomena of core-concrete interactions impact upon containment integrity of light water reactors (LWR) following postulated complete meltdown of the core by containment pressurization, production of combustible gases, and basemat penetration. Experiments were performed with nonreactor materials to investigate one aspect of this problem, heat transfer between overlying immiscible liquids whose interface is disturbed by a transverse non-condensable gas flux emanating from below. Hydrodynamic studies were performed to test a criterion for onset of entrainment due to bubbling through the interface and subsequent heat transfer studies were performed to assess the effect of bubbling on interfacial heat transfer rates, both with and without bubble induced entrainment. Non entraining interfacial heat transfer data with mercury-water/oil fluid pairs were observed to be bounded from below within a factor of two to three by the Szekeley surface renewal heat transfer model.
A review of NASA combustor and turbine heat transfer research
NASA Technical Reports Server (NTRS)
Rudey, R. A.; Graham, R. W.
1984-01-01
The thermal design of the combustor and turbine of a gas turbine engine poses a number of difficult heat transfer problems. The importance of improved prediction techniques becomes more critical in anticipation of future generations of gas turbine engines which will operate at higher cycle pressure and temperatures. Research which addresses many of the complex heat transfer processes holds promise for yielding significant improvements in prediction of metal temperatures. Such research involves several kinds of program including: (1) basic experiments which delineate the fundamental flow and heat transfer phenomena that occur in the hot sections of the gas turbine but at low enthalpy conditions; (2) analytical modeling of these flow and heat transfer phenomena which results from the physical insights gained in experimental research; and (3) verification of advanced prediction techniques in facilities which operate near the real engine thermodynamic conditions. In this paper, key elements of the NASA program which involves turbine and combustor heat transfer research will be described and discussed.
Heat transfer to air from a yawed cylinder
NASA Astrophysics Data System (ADS)
Kraabel, J. S.; McKillop, A. A.; Baughn, J. W.
1982-03-01
An experimental study designed to investigate heat transfer to air from a yawed cylinder is described. Measurements were made at Reynolds numbers of 34,000 and 106,000, and yaws varied from cross flow (beta = 0 deg) to 60 deg. The independence principle is found to be valid for heat transfer at the stagnation line and in the laminar boundary layer. Although this principle would not be expected to extend to the wake, the local heat transfer to the wake is not greatly affected by yaw for beta not greater than 40 deg. The heat transfer results can be explained in terms of a secondary vortex located downstream of an initial separation point and followed by a primary eddy. For high yaws and high normal Reynolds numbers, the heat transfer is similar to that which occurs in cross flow approaching critical flow.
Boyer, B.D.; Parlatan, Y.; Slovik, G.C.
1995-09-01
RELAP5 MOD3.1.1 is being used to simulate Loss of Coolant Accidents (LOCA) for the Simplified Boiling Water Reactor (SBWR) being proposed by General Electric (GE). One of the major components associated with the SBWR is the Passive Containment Cooling System (PCCS) which provides the long-term heat sink to reject decay heat. The RELAP5 MOD3.1.1 code is being assessed for its ability to represent accurately the PCCS. Data from the Phase 1, Step 1 Heat Transfer Tests performed at Toshiba`s Gravity-Driven Integral Full-Height Test for Passive Heat Removal (GIRAFFE) facility will be used for assessing the ability of RELAP5 to model condensation in the presence of noncondensables. The RELAP5 MOD3.1.1 condensation model uses the University of California at Berkeley (UCB) correlation developed by Vierow and Schrock. The RELAP5 code uses this heat transfer coefficient with the gas velocity effect multiplier being limited to 2. This heat transfer option was used to analyze the condensation heat transfer in the GIRAFFE PCCS heat exchanger tubes in the Phase 1, Step 1 Heat Transfer Tests which were at a pressure of 3 bar and had a range of nitrogen partial pressure fractions from 0.0 to 0.10. The results of a set of RELAP5 calculations at these conditions were compared with the GIRAFFE data. The effects of PCCS cell noding on the heat transfer process were also studied. The UCB correlation, as implemented in RELAP5, predicted the heat transfer to {plus_minus}5% of the data with a three--node model. The three-node model has a large cell in the entrance region which smeared out the entrance effects on the heat transfer, which tend to overpredict the condensation. Hence, the UCB correlation predicts condensation heat transfer correlation implemented in the code must be removed to allow for accurate calculations with smaller cell sizes.
Conjugate heat transfer with the entropic lattice Boltzmann method
NASA Astrophysics Data System (ADS)
Pareschi, G.; Frapolli, N.; Chikatamarla, S. S.; Karlin, I. V.
2016-07-01
A conjugate heat-transfer model is presented based on the two-population entropic lattice Boltzmann method. The present approach relies on the extension of Grad's boundary conditions to the two-population model for thermal flows, as well as on the appropriate exact conjugate heat-transfer condition imposed at the fluid-solid interface. The simplicity and efficiency of the lattice Boltzmann method (LBM), and in particular of the entropic multirelaxation LBM, are retained in the present approach, thus enabling simulations of turbulent high Reynolds number flows and complex wall boundaries. The model is validated by means of two-dimensional parametric studies of various setups, including pure solid conduction, conjugate heat transfer with a backward-facing step flow, and conjugate heat transfer with the flow past a circular heated cylinder. Further validations are performed in three dimensions for the case of a turbulent flow around a heated mounted cube.
Conjugate heat transfer with the entropic lattice Boltzmann method.
Pareschi, G; Frapolli, N; Chikatamarla, S S; Karlin, I V
2016-07-01
A conjugate heat-transfer model is presented based on the two-population entropic lattice Boltzmann method. The present approach relies on the extension of Grad's boundary conditions to the two-population model for thermal flows, as well as on the appropriate exact conjugate heat-transfer condition imposed at the fluid-solid interface. The simplicity and efficiency of the lattice Boltzmann method (LBM), and in particular of the entropic multirelaxation LBM, are retained in the present approach, thus enabling simulations of turbulent high Reynolds number flows and complex wall boundaries. The model is validated by means of two-dimensional parametric studies of various setups, including pure solid conduction, conjugate heat transfer with a backward-facing step flow, and conjugate heat transfer with the flow past a circular heated cylinder. Further validations are performed in three dimensions for the case of a turbulent flow around a heated mounted cube. PMID:27575234
Heat-Transfer Head For Stirling-Cycle Machine
NASA Technical Reports Server (NTRS)
Emigh, Stuart G.; Lehmann, Gregory A.; Noble, Jack E.
1995-01-01
New common heat-transfer head for two cylinders of opposed-cylinder Stirling-cycle machine performs function formerly performed by two heat acceptors-one for each cycle. Simplifies structure of machine and increases efficiency of operation by reducing resistance to flow of working gas and/or increasing transfer of heat to or from working gas during flow between compression and expansion spaces of machine.
Laser Measurement Of Convective-Heat-Transfer Coefficient
NASA Technical Reports Server (NTRS)
Porro, A. Robert; Hingst, Warren R.; Chriss, Randall M.; Seablom, Kirk D.; Keith, Theo G., Jr.
1994-01-01
Coefficient of convective transfer of heat at spot on surface of wind-tunnel model computed from measurements acquired by developmental laser-induced-heat-flux technique. Enables non-intrusive measurements of convective-heat-transfer coefficients at many points across surfaces of models in complicated, three-dimensional, high-speed flows. Measurement spot scanned across surface of model. Apparatus includes argon-ion laser, attenuator/beam splitter electronic shutter infrared camera, and subsystem.
CFD Extraction of Heat Transfer Coefficient in Cryogenic Propellant Tanks
NASA Technical Reports Server (NTRS)
Yang, H. Q.; West, Jeff
2015-01-01
Current reduced-order thermal model for cryogenic propellant tanks is based on correlations built for flat plates collected in the 1950's. The use of these correlations suffers from inaccurate geometry representation; inaccurate gravity orientation; ambiguous length scale; and lack of detailed validation. This study uses first-principles based CFD methodology to compute heat transfer from the tank wall to the cryogenic fluids and extracts and correlates the equivalent heat transfer coefficient to support reduced-order thermal model. The CFD tool was first validated against available experimental data and commonly used correlations for natural convection along a vertically heated wall. Good agreements between the present prediction and experimental data have been found for flows in laminar as well turbulent regimes. The convective heat transfer between the tank wall and cryogenic propellant, and that between the tank wall and ullage gas were then simulated. The results showed that the commonly used heat transfer correlations for either vertical or horizontal plate over-predict heat transfer rate for the cryogenic tank, in some cases by as much as one order of magnitude. A characteristic length scale has been defined that can correlate all heat transfer coefficients for different fill levels into a single curve. This curve can be used for the reduced-order heat transfer model analysis.
Two-Dimensional Heat Transfer in a Heterogeneous Fracture Network
NASA Astrophysics Data System (ADS)
Gisladottir, V. R.; Roubinet, D.; Tartakovsky, D. M.
2015-12-01
Geothermal energy harvesting requires extraction and injection of geothermal fluid. Doing so in an optimal way requires a quantitative understanding of site-specific heat transfer between geothermal fluid and the ambient rock. We develop a heat transfer particle-tracking approach to model that interaction. Fracture-network models of heat transfer in fractured rock explicitly account for the presence of individual fractures, ambient rock matrix, and fracture-matrix interfaces. Computational domains of such models span the meter scale, whereas fracture apertures are on the millimeter scale. The computations needed to model these multi-scale phenomenon can be prohibitively expensive, even for methods using nonuniform meshes. Our approach appreciably decreases the computational costs. Current particle-tracking methods usually assume both infinite matrix and one-dimensional (1D) heat transfer in the matrix blocks. They rely on 1D analytical solutions for heat transfer in a single fracture, which can lead to large predictive errors. Our two-dimensional (2D) heat transfer simulation algorithm is mesh-free and takes into account both longitudinal and transversal heat conduction in the matrix. It uses a probabilistic model to transfer particle to the appropriate neighboring fracture unless it returns to the fracture of origin or remains in the matrix. We use this approach to look at the impact of a fracture-network topology (e.g. the importance of smaller scale fractures), as well as the matrix block distribution on the heat transport in heterogeneous fractured rocks.
Enhanced two phase flow in heat transfer systems
Tegrotenhuis, Ward E; Humble, Paul H; Lavender, Curt A; Caldwell, Dustin D
2013-12-03
A family of structures and designs for use in devices such as heat exchangers so as to allow for enhanced performance in heat exchangers smaller and lighter weight than other existing devices. These structures provide flow paths for liquid and vapor and are generally open. In some embodiments of the invention, these structures can also provide secondary heat transfer as well. In an evaporate heat exchanger, the inclusion of these structures and devices enhance the heat transfer coefficient of the evaporation phase change process with comparable or lower pressure drop.
Flow characteristics and heat transfer in wavy walled channels
NASA Astrophysics Data System (ADS)
Mills, Zachary; Shah, Tapan; Monts, Vontravis; Warey, Alok; Balestrino, Sandro; Alexeev, Alexander
2013-11-01
Using lattice Boltzmann simulations, we investigated the effects of wavy channel geometry on the flow and heat transfer within a parallel plate heat exchanger. We observed three distinct flow regimes that include steady flow with and without recirculation and unsteady time-periodic flow. We determined the critical Reynolds numbers at which the flow transitions between different flow regimes. To validate our computational results, we compared the simulated flow structures with the structures observed in a flowing soap film. Furthermore, we examine the effects of the wavy channel geometry on the heat transfer. We find that the unsteady flow regime drastically enhances the rate of heat transfer and show that heat exchangers with wavy walls outperform currently used heat exchangers with similar volume and power characteristics. Results from our study point to a simple and efficient method for increasing performance in compact heat exchangers.
Droplet Evaporator For High-Capacity Heat Transfer
NASA Technical Reports Server (NTRS)
Valenzuela, Javier A.
1993-01-01
Proposed heat-exchange scheme boosts heat transfer per unit area. Key component is generator that fires uniform size droplets of subcooled liquid at hot plate. On impact, droplets spread out and evaporate almost instantly, removing heat from plate. In practice, many generator nozzles arrayed over evaporator plate.
An assessment on convective and radiative heat transfer modelling in tubular solid oxide fuel cells
NASA Astrophysics Data System (ADS)
Sánchez, D.; Muñoz, A.; Sánchez, T.
Four models of convective and radiative heat transfer inside tubular solid oxide fuel cells are presented in this paper, all of them applicable to multidimensional simulations. The work is aimed at assessing if it is necessary to use a very detailed and complicated model to simulate heat transfer inside this kind of device and, for those cases when simple models can be used, the errors are estimated and compared to those of the more complex models. For the convective heat transfer, two models are presented. One of them accounts for the variation of film coefficient as a function of local temperature and composition. This model gives a local value for the heat transfer coefficients and establishes the thermal entry length. The second model employs an average value of the transfer coefficient, which is applied to the whole length of the duct being studied. It is concluded that, unless there is a need to calculate local temperatures, a simple model can be used to evaluate the global performance of the cell with satisfactory accuracy. For the radiation heat transfer, two models are presented again. One of them considers radial radiation exclusively and, thus, radiative exchange between adjacent cells is neglected. On the other hand, the second model accounts for radiation in all directions but increases substantially the complexity of the problem. For this case, it is concluded that deviations between both models are higher than for convection. Actually, using a simple model can lead to a not negligible underestimation of the temperature of the cell.
Numerical Simulation of Flow Instability and Heat Transfer
NASA Astrophysics Data System (ADS)
Dou, Hua-Shu; Jiang, Gang
2014-11-01
This paper numerically investigates the physical mechanism of flow instability and heat transfer of natural convection in a cavity with thin fin(s). The left and the right walls of the cavity are differentially heated. The cavity is given an initial temperature, and the thin fin(s) is fixed on the hot wall in order to control the heat transfer. The finite volume method with the SIMPLE scheme is used to simulate the flow. Distributions of the temperature, the pressure, the velocity and the total pressure are achieved. Then, the energy gradient method is employed to study the physical mechanism of flow instability and the effect of the thin fin(s) on heat transfer. Based on the energy gradient method, the energy gradient function K represents the characteristic of flow instability. It is observed from the simulation results that the positions where instabilities take place in the temperature contours accord well with those of higher K value, which demonstrates that the energy gradient method reveals the physical mechanism of flow instability. Furthermore, the effect of the fin length, the fin position, the fin number, and Ra on heat transfer is also investigated. It is found that the effect of the fin length on heat transfer is negligible when Ra is relatively high. When there is only one fin, the most efficient heat transfer rate is achieved as the fin is fixed at the middle height of the cavity. The fin blocks heat transfer with a relatively small Ra, but the fin enhances heat transfer with a relatively large Ra. The fin(s) enhances heat transfer gradually with the increase of Ra under the influence of the thin fin(s). Finally, it is observed that both Kmax and Ra can reveal the physical mechanism of natural convection from different approaches.
Effects of Nonequilibrium at Edge of Boundary Layer on Convective Heat Transfer to a Blunt Body
NASA Technical Reports Server (NTRS)
Goekcen, Tahir; Edwards, Thomas A. (Technical Monitor)
1996-01-01
This investigation is a continuation of a previous study on nonequilibrium convective heat transfer to a blunt body. In the previous study, for relatively high Reynolds number flows, it was found that: nonequilibrium convective heat transfer to a blunt body is not strongly dependent on freestream parameters, provided that the thermochemical equilibrium is reached at the edge of boundary layer; and successful testing of convective heat transfer in an arc-jet environment is possible by duplicating the surface pressure and total enthalpy. The nonequilibrium convective heat transfer computations are validated against the results of Fay and Riddell/Goulard theory. Present work investigates low Reynolds number conditions which are typical in an actual arc-jet flow environment. One expects that there will be departures from the Fay and Riddell/Goulard result since certain assumptions of the classical theory are not satisfied. These departures are of interest because the Fay and Riddell/Goulard formulas are extensively used in arc-jet testing (e.g., to determine the enthalpy of the flow and the catalytic efficiency of heat shield materials). For practical sizes of test materials, density of the test flow (and Reynolds number) in an arc-jet is such that thermochemical equilibrium may not be reached at the edge of boundary layer. For blunt body flows of nitrogen and air, computations will be presented to show the effects of thermochemical nonequilibrium at the boundary layer edge on nonequilibrium heat transfer.
An experimental study of turbine vane heat transfer with leading edge and downstream film cooling
NASA Technical Reports Server (NTRS)
Nirmalan, V.; Hylton, L. D.
1989-01-01
This paper presents the effects of downstream film cooling, with and without leading edge showerhead film cooling, on turbine-vane external heat transfer. Steady-state experimental measurements were made in a three-vane linear two-dimensional cascade. The principal independent parameters were maintained over ranges consistent with actual engine conditions. The test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. The data obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The downstream film cooling process was shown to be a complex interaction of two competing mechanisms. The thermal dilution effect, associated with the injection of relatively cold fluid, results in a decrease in the heat transfer to the airfoil. Conversely, the turbulence augmentation, produced by the injection process, results in increased heat transfer to the airfoil.
An experimental study of turbine vane heat transfer with leading edge and downstream film cooling
NASA Astrophysics Data System (ADS)
Nirmalan, V.; Hylton, L. D.
1989-06-01
This paper presents the effects of downstream film cooling, with and without leading edge showerhead film cooling, on turbine-vane external heat transfer. Steady-state experimental measurements were made in a three-vane linear two-dimensional cascade. The principal independent parameters were maintained over ranges consistent with actual engine conditions. The test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. The data obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The downstream film cooling process was shown to be a complex interaction of two competing mechanisms. The thermal dilution effect, associated with the injection of relatively cold fluid, results in a decrease in the heat transfer to the airfoil. Conversely, the turbulence augmentation, produced by the injection process, results in increased heat transfer to the airfoil.
Radiation Heat Transfer Procedures for Space-Related Applications
NASA Technical Reports Server (NTRS)
Chai, John C.
2000-01-01
Over the last contract year, a numerical procedure for combined conduction-radiation heat transfer using unstructured grids has been developed. As a result of this research, one paper has been published in the Numerical Heat Transfer Journal. One paper has been accepted for presentation at the International Center for Heat and Mass Transfer's International Symposium on Computational Heat Transfer to be held in Australia next year. A journal paper is under review by my NASA's contact. A conference paper for the ASME National Heat Transfer conference is under preparation. In summary, a total of four (4) papers (two journal and two conference) have been published, accepted or are under preparation. There are two (2) to three (3) more papers to be written for the project. In addition to the above publications, one book chapter, one journal paper and six conference papers have been published as a result of this project. Over the last contract year, the research project resulted in one Ph.D. thesis and partially supported another Ph.D. student. My NASA contact and myself have formulated radiation heat transfer procedures for materials with different indices of refraction and for combined conduction-radiation heat transfer. We are trying to find other applications for the procedures developed under this grant.
Conjugate Compressible Fluid Flow and Heat Transfer in Ducts
NASA Technical Reports Server (NTRS)
Cross, M. F.
2011-01-01
A computational approach to modeling transient, compressible fluid flow with heat transfer in long, narrow ducts is presented. The primary application of the model is for analyzing fluid flow and heat transfer in solid propellant rocket motor nozzle joints during motor start-up, but the approach is relevant to a wide range of analyses involving rapid pressurization and filling of ducts. Fluid flow is modeled through solution of the spatially one-dimensional, transient Euler equations. Source terms are included in the governing equations to account for the effects of wall friction and heat transfer. The equation solver is fully-implicit, thus providing greater flexibility than an explicit solver. This approach allows for resolution of pressure wave effects on the flow as well as for fast calculation of the steady-state solution when a quasi-steady approach is sufficient. Solution of the one-dimensional Euler equations with source terms significantly reduces computational run times compared to general purpose computational fluid dynamics packages solving the Navier-Stokes equations with resolved boundary layers. In addition, conjugate heat transfer is more readily implemented using the approach described in this paper than with most general purpose computational fluid dynamics packages. The compressible flow code has been integrated with a transient heat transfer solver to analyze heat transfer between the fluid and surrounding structure. Conjugate fluid flow and heat transfer solutions are presented. The author is unaware of any previous work available in the open literature which uses the same approach described in this paper.
Radiative heat transfer in the extreme near field.
Kim, Kyeongtae; Song, Bai; Fernández-Hurtado, Víctor; Lee, Woochul; Jeong, Wonho; Cui, Longji; Thompson, Dakotah; Feist, Johannes; Reid, M T Homer; García-Vidal, Francisco J; Cuevas, Juan Carlos; Meyhofer, Edgar; Reddy, Pramod
2015-12-17
Radiative transfer of energy at the nanometre length scale is of great importance to a variety of technologies including heat-assisted magnetic recording, near-field thermophotovoltaics and lithography. Although experimental advances have enabled elucidation of near-field radiative heat transfer in gaps as small as 20-30 nanometres (refs 4-6), quantitative analysis in the extreme near field (less than 10 nanometres) has been greatly limited by experimental challenges. Moreover, the results of pioneering measurements differed from theoretical predictions by orders of magnitude. Here we use custom-fabricated scanning probes with embedded thermocouples, in conjunction with new microdevices capable of periodic temperature modulation, to measure radiative heat transfer down to gaps as small as two nanometres. For our experiments we deposited suitably chosen metal or dielectric layers on the scanning probes and microdevices, enabling direct study of extreme near-field radiation between silica-silica, silicon nitride-silicon nitride and gold-gold surfaces to reveal marked, gap-size-dependent enhancements of radiative heat transfer. Furthermore, our state-of-the-art calculations of radiative heat transfer, performed within the theoretical framework of fluctuational electrodynamics, are in excellent agreement with our experimental results, providing unambiguous evidence that confirms the validity of this theory for modelling radiative heat transfer in gaps as small as a few nanometres. This work lays the foundations required for the rational design of novel technologies that leverage nanoscale radiative heat transfer. PMID:26641312
Flow and heat transfer of petal shaped double tube
NASA Astrophysics Data System (ADS)
Shakouchi, Toshihiko; Kawashima, Yuki; Tsujimoto, Koichi; Ando, Toshitake
2014-06-01
In this study, the flow and heat transfer characteristics of petal-shaped double tube with 6 petals are examined experimentally for a compact heat exchanger. As results, the heat transfer rate, Q, of the 6 petal shaped double tube (6-p tube) is much larger than that, Qp, of conventional circular double tube in all Reynolds number Rein,h (where, the reference length is hydraulic diameter) ranges. For example, at Rein,h =(0.5～1.0)× 104 it is about 4 times of Qp. The heat transfer enhancement of 6-p tube is by the increase of heat transfer area, wetting perimeter, and a highly fluctuating flow, and Q of the 6-p tube can be expressed by Q [kW/m] = 0.54Rein,h + 2245.
Radiative heat transfer in low-dimensional systems -- microscopic mode
NASA Astrophysics Data System (ADS)
Woods, Lilia; Phan, Anh; Drosdoff, David
2013-03-01
Radiative heat transfer between objects can increase dramatically at sub-wavelength scales. Exploring ways to modulate such transport between nano-systems is a key issue from fundamental and applied points of view. We advance the theoretical understanding of radiative heat transfer between nano-objects by introducing a microscopic model, which takes into account the individual atoms and their atomic polarizabilities. This approach is especially useful to investigate nano-objects with various geometries and give a detailed description of the heat transfer distribution. We employ this model to study the heat exchange in graphene nanoribbon/substrate systems. Our results for the distance separations, substrates, and presence of extended or localized defects enable making predictions for tailoring the radiative heat transfer at the nanoscale. Financial support from the Department of Energy under Contract No. DE-FG02-06ER46297 is acknowledged.
NASA Astrophysics Data System (ADS)
Shinomiya, Naruaki; Nishimura, Nobuya; Iyota, Hiroyuki; Nomura, Tomohiro
Split type air conditioners are operated actually in the situation unlike the condition that was described in a product catalog. On the other hand, exhaust heat from air conditioner is considered as one of the causes of heat island problem in urban area, and the air conditioner performance and heat load affect exhaust heat amount. In this study, air conditioner performances in both standard summer day and severe hot day were examined by dynamic simulation which considered outdoor weather changes. As a result, actual performances of the air conditioner were demonstrated as a function of outdoor temperature, heat load and indoor temperature. The higher the outdoor temperature and heat load rise, the smaller influences of indoor temperature against COP became. In standard summer day, relative performance exceeded by 15 to 45% than that of JIS operating condition. Also, COP in severe hot day decreased about 6% at the peak time than that of standard day. As a result, the air conditioner exhaust heat during one day which was predicted by the proposed simulation model became about 16% smaller than the conventional prediction model.
Heat transfer with very high free-stream turbulence and heat transfer with streamwise vortices
NASA Technical Reports Server (NTRS)
Moffat, Robert J.; Maciejewski, Paul; Eaton, John K.; Pauley, Wayne
1987-01-01
Two experimental programs related to augmentation of heat transfer by complex flow characteristics are reviewed. The first program deals with very high turbulence (up to 63 percent) which was shown to result in Stanton numbers as much as five times the expected values. Results from a number of trials show that fixing the free stream velocity, x-Reynolds number, turbulence intensity and integral length scale does not fix the Stanton number. Two such cases were found in which the Stanton number of one was 40 percent larger than the other. Mean velocity and mean temperature profiles are presented, as well as profiles of turbulence intensity within the boundary layer. The second program deals with vortices originating at bluff bodies and traveling downstream embedded in the wall boundary layer. Velocity vector maps from the boundary layers and distributions of Stanton number on the wall are presented for three types of bodies: square, cylindrical and teardrop. The heat transfer and velocity maps do not show evidence of the expected horseshoe vortices but, instead, show a strong common flow up vortex pair. The fluid mechanic mechanism responsible for this secondary flow field has not yet been identified.
Wall-to-suspension heat transfer in circulating fluidized beds
Wirth, K.E.
1995-12-31
The wall-to-suspension heat transfer in circulating fluidized beds depends on the fluid mechanics immediately near the wall and on the thermal properties of the gas used. Experimental investigations of circulating fluidized beds of low dimensionless pressure gradients with different solid particles like bronze, glass and polystyrene at ambient temperatures showed no influence of the conductivity and the heat capacity of the solids on the heat transfer coefficient. Consequently the heat transfer coefficient in the form of the dimensionless Nusselt number can be described by the dimensionless numbers which characterize the gas-solid-flow near the wall. These numbers are the Archimedes number and the pressure drop-number. The last number relates the cross-sectional average solids concentration to the solids concentration at minimum fluidization condition. With the aid of a model of segregated vertical gas-solid flow, the flow pattern in the wall region can be calculated and thus the wall heat transfer which depends only on heat conduction in the gas and on the convective heat transfer by the gas. With elevated suspension temperatures, radiation contributes additionally to the heat transfer. When the solids concentration is low, the effect of the radiation on the heat transfer is high. Increasing solids concentration results in a decrease of the radiation effect due to the wall being shielded from the radiation of the hot particles in the core region by the cold solids clusters moving down the wall. A simple correlation is presented for calculating the wall-to-suspension heat transfer in circulating fluidized beds.
Air-side flow and heat transfer in compact heat exchangers: A discussion of enhancement mechanisms
Jacobi, A.M.; Shah, R.K.
1998-10-01
The behavior of air flows in complex heat exchanger passages is reviewed with a focus on the heat transfer effects of boundary-layer development, turbulence, spanwise and streamwise vortices, and wake management. Each of these flow features is discussed for the plain, wavy, and interrupted passages found in contemporary compact heat exchanger designs. Results from the literature are used to help explain the role of these mechanisms in heat transfer enhancement strategies.
A review on boiling heat transfer enhancement with nanofluids
2011-01-01
There has been increasing interest of late in nanofluid boiling and its use in heat transfer enhancement. This article covers recent advances in the last decade by researchers in both pool boiling and convective boiling applications, with nanofluids as the working fluid. The available data in the literature is reviewed in terms of enhancements, and degradations in the nucleate boiling heat transfer and critical heat flux. Conflicting data have been presented in the literature on the effect that nanofluids have on the boiling heat-transfer coefficient; however, almost all researchers have noted an enhancement in the critical heat flux during nanofluid boiling. Several researchers have observed nanoparticle deposition at the heater surface, which they have related back to the critical heat flux enhancement. PMID:21711794
Determination of the heat transfer coefficients in porous media
Kim, L.V.
1994-06-01
The process of transpiration cooling is considered. Methods are suggested for estimating the volumetric coefficient of heat transfer with the use of a two-temperature model and the surface heat transfer coefficient at entry into a porous wall. The development of new technology under conditions of increasing heat loads puts the search for effective methods of heat transfer enhancement in the forefront of theoretical investigations. One of the promising trends in the solution of this problem is the use of porous materials (PM) in the elements of power units. For thermal protection against convective or radiative heat fluxes, the method of transpiration cooling is successfully used. The mechanism operative in the thermal protection involves the injection of a coolant through a porous medium to produce a screen over the contour of a body in a flow for removing heat energy from the skeleton of the porous material.
A review on boiling heat transfer enhancement with nanofluids.
Barber, Jacqueline; Brutin, David; Tadrist, Lounes
2011-01-01
There has been increasing interest of late in nanofluid boiling and its use in heat transfer enhancement. This article covers recent advances in the last decade by researchers in both pool boiling and convective boiling applications, with nanofluids as the working fluid. The available data in the literature is reviewed in terms of enhancements, and degradations in the nucleate boiling heat transfer and critical heat flux. Conflicting data have been presented in the literature on the effect that nanofluids have on the boiling heat-transfer coefficient; however, almost all researchers have noted an enhancement in the critical heat flux during nanofluid boiling. Several researchers have observed nanoparticle deposition at the heater surface, which they have related back to the critical heat flux enhancement. PMID:21711794
A Compact Remote Heat Transfer Device for Space Cryocoolers
NASA Astrophysics Data System (ADS)
Yan, T.; Zhao, Y.; Liang, T.
In this paper a compact remote heat transfer device (CRHD) for cryocoolers is proposed. This device is especially attractive in cases where cryocoolers are not easy to set near the heat source, generally the infrared sensor. The CRHD is designed on basis of the concept of loop heat pipes, while the primary evaporator is located near the cryocooler cold head and a simple tube-in-tube secondary evaporator is remotely located and thermally connected with the heat source for cooling. With such a device a cooling power of 1 W is achieved across a heat transfer distance of about 2 m. The major problem of this device is the low heat transfer efficiency (1 W of net cooling power at the cost of about 7 W of cooling power from the cryocooler), and in the future a secondary wicked evaporator will be used instead of the tube-in-tube evaporator in order to improve the efficiency.
Intensification of heat transfer by changing the burner nozzle
NASA Astrophysics Data System (ADS)
DzurÅák, Róbert; Kizek, Ján; Jablonský, Gustáv
2016-06-01
Thermal aggregates are using burner which burns combustible mixture with an oxidizing agent, by adjustment of the burner nozzle we can achieve better conditions of combustion to intensify heat transfer at furnace space. The aim of the present paper was using a computer program Ansys Workbench to create a computer simulation which analyzes the impact of the nozzle on the shape of a flame thereby intensifies heat transfer in rotary drum furnaces and radiation heat transfer from the flue gas into the furnace space. Article contains analysis of the geometry of the burner for achieving temperature field in a rotary drum furnace using oxy-combustion and the practical results of computer simulations
Radiation heat transfer in two-phase media
Adzerikho, K.S.
1988-05-01
The state of the art of approximate and numerical methods of the theory of radiation heat transfer is analyzed. The principles for producing engineering methods of computing the radiation heat-transfer characteristics in power plants are examined. These principles include: the integration of the transport equation, computing the radiation heat transfer in nonisothermal two-phase media bounded by emitting and reflecting surfaces, the thermal efficiency of screens as a function of the optical properties of the boundary surfaces and the furnace medium, the scattering processes, temperature distribution, and a program NOTAK in the FORTRAN-IV language.
Design code verification of external heat transfer coefficients
NASA Astrophysics Data System (ADS)
Soechting, F. O.; Sharma, O. P.
1988-07-01
A comparative study is conducted for measured and predicted heat-transfer coefficients of air-cooled turbine blade airfoils. A modified version of the STAN-5 boundary layer code was used to obtain analytical predictions of the heat transfer levels for the cascade test conditions. A two-dimensional cascade test was conducted at engine-level Mach number and Reynolds number distributions in order to obtain baseline data that can be used with engine data in order to quantify the effects of environmental conditions on heat transfer levels and distributions.
Turbulent flow and heat transfer in rotating channels and tubes
NASA Astrophysics Data System (ADS)
Mitiakov, V. Y.; Petropavlovskii, R. R.; Ris, V. V.; Smirnov, E. M.; Smirnov, S. A.
This document is a reduction of the author's experimental results on turbulent flow characteristics and heat transfer in rotating channels whose axes are parallel to the plane of rotation. Substantial dissimilarities of longitudinal velocity field profile and pulsational characteristics are caused by effects of stabilization and destabilization and secondary flow production. Local heat transfer coefficients vary over the perimeter of the tube section connecting detected flow peculiarities. It is shown that the increase in rotational intensity caused an increase in the relative dissimilarity of the local heat transfer coefficients and increased their mean value.
Transfer heat in a resin sheath
Wharry, S.R. Jr.
1996-02-01
As a material of construction for heat exchangers, fluoropolymers offer a combination of low cost and performance that is difficult for other materials to match. Durable, pliable, and less brittle than glass and graphite, fluoropolymers are generally specified over those materials in heat exchangers. Fluoropolymers have also displaced certain metals, depending on their susceptibility to corrosion from aggressive chemicals. Since making their debut in shell-and-tube models more than 30 years ago, fluoropolymers have also found their way into other configurations, namely reactor coils and immersion coils. Although fluoropolymer exchangers have proven their worth, there are still obstacles to overcome. One is the bias that exists toward process equipment that is made of plastic or other synthetic resins, particularly in high-heat environments. Secondly, there is the assumption that because fluoropolymers are inherently poor conductors of heat, they are odd candidates for heat exchangers. The paper discusses the advantages of fluoropolymer use in heat exchangers.
Nanoscale heat transfer in the head-disk interface for heat assisted magnetic recording
NASA Astrophysics Data System (ADS)
Wu, Haoyu; Xiong, Shaomin; Canchi, Sripathi; Schreck, Erhard; Bogy, David
2016-02-01
Laser heating has been introduced in heat-assisted magnetic recording in order to reduce the magnetic coercivity and enable data writing. However, the heat flow inside a couple of nanometers head-disk gap is still not well understood. An experimental stage was built for studying heat transfer in the head-disk interface (HDI) and the heat-induced instability of the HDI. A laser heating system is included to produce a heated spot on the disk at the position of the slider. A floating air bearing slider is implemented in the stage for sensing the temperature change of the slider due to the heat transfer from the disk by the use of an embedded contact sensor, and the gap between the two surfaces is controlled by the use of a thermal fly-height control actuator. By using this system, we explore the dependency of the heat transfer on the gap spacing as well as the disk temperature.
Many-body radiative heat transfer theory.
Ben-Abdallah, Philippe; Biehs, Svend-Age; Joulain, Karl
2011-09-01
In this Letter, an N-body theory for the radiative heat exchange in thermally nonequilibrated discrete systems of finite size objects is presented. We report strong exaltation effects of heat flux which can be explained only by taking into account the presence of many-body interactions. Our theory extends the standard Polder and van Hove stochastic formalism used to evaluate heat exchanges between two objects isolated from their environment to a collection of objects in mutual interaction. It gives a natural theoretical framework to investigate the photon heat transport properties of complex systems at the mesoscopic scale. PMID:22026672
Heat transfer through an extended surface containing He II
Van Sciver, S.W.
1999-02-01
A semi-analytic solution for the heat transfer process between a He II pressurized bath and a saturated tube-type heat exchanger is presented. The problem is modeled with an extended surface heat transfer formulation analogous to that in conventional conduction. The process is governed by Kapitza conductance and counterflow within the bulk fluid in the tube. The resulting nonlinear differential equation may be integrated for the special case of constant properties, yielding a simple solution applicable to design and analysis of practical heat exchangers.
Fourier analysis of conductive heat transfer for glazed roofing materials
Roslan, Nurhana Lyana; Bahaman, Nurfaradila; Almanan, Raja Noorliyana Raja; Ismail, Razidah; Zakaria, Nor Zaini
2014-07-10
For low-rise buildings, roof is the most exposed surface to solar radiation. The main mode of heat transfer from outdoor via the roof is conduction. The rate of heat transfer and the thermal impact is dependent on the thermophysical properties of roofing materials. Thus, it is important to analyze the heat distribution for the various types of roofing materials. The objectives of this paper are to obtain the Fourier series for the conductive heat transfer for two types of glazed roofing materials, namely polycarbonate and polyfilled, and also to determine the relationship between the ambient temperature and the conductive heat transfer for these materials. Ambient and surface temperature data were collected from an empirical field investigation in the campus of Universiti Teknologi MARA Shah Alam. The roofing materials were installed on free-standing structures in natural ventilation. Since the temperature data are generally periodic, Fourier series and numerical harmonic analysis are applied. Based on the 24-point harmonic analysis, the eleventh order harmonics is found to generate an adequate Fourier series expansion for both glazed roofing materials. In addition, there exists a linear relationship between the ambient temperature and the conductive heat transfer for both glazed roofing materials. Based on the gradient of the graphs, lower heat transfer is indicated through polyfilled. Thus polyfilled would have a lower thermal impact compared to polycarbonate.
Wake-induced unsteady stagnation-region heat transfer measurements
Magari, P.J.; LaGraff, L.E. . Dept. of Mechanical and Aerospace Engineering)
1994-01-01
An experimental investigation of wake-induced unsteady heat transfer in the stagnation region of a cylinder was conducted. The objective of the study was to create a quasi-steady representation of the stator/rotor interaction in a gas turbine using two stationary cylinders in crossflow. In this simulation, a larger cylinder, representing the leading-edge region of a rotor blade, was immersed in the wake of a smaller cylinder, representing the trailing-edge region of a stator vane. Time-averaged and time-resolved heat transfer results were obtained over a wide range of Reynolds number at two Mach number: one incompressible and one transonic. The tests were conducted at Reynolds numbers, Mach numbers, and gas-to-wall temperature ratios characteristic of turbine engine conditions in an isentropic compression-heated transient wind tunnel (LICH tube). The augmentation of the heat transfer in the stagnation region due to wake unsteadiness was documented by comparison with isolated cylinder tests. It was found that the time-averaged heat transfer rate at the stagnation line, expressed in terms of the Frossling number (Nu/[radical]RE), reached a maximum independent of the Reynolds number. The power spectra and cross-correlation of the heat transfer signals in the stagnation region revealed the importance of large vortical structures shed from upstream wake generator. These structures caused large positive and negative excursions about the mean heat transfer rate in the stagnation region.
Fourier analysis of conductive heat transfer for glazed roofing materials
NASA Astrophysics Data System (ADS)
Roslan, Nurhana Lyana; Bahaman, Nurfaradila; Almanan, Raja Noorliyana Raja; Ismail, Razidah; Zakaria, Nor Zaini
2014-07-01
For low-rise buildings, roof is the most exposed surface to solar radiation. The main mode of heat transfer from outdoor via the roof is conduction. The rate of heat transfer and the thermal impact is dependent on the thermophysical properties of roofing materials. Thus, it is important to analyze the heat distribution for the various types of roofing materials. The objectives of this paper are to obtain the Fourier series for the conductive heat transfer for two types of glazed roofing materials, namely polycarbonate and polyfilled, and also to determine the relationship between the ambient temperature and the conductive heat transfer for these materials. Ambient and surface temperature data were collected from an empirical field investigation in the campus of Universiti Teknologi MARA Shah Alam. The roofing materials were installed on free-standing structures in natural ventilation. Since the temperature data are generally periodic, Fourier series and numerical harmonic analysis are applied. Based on the 24-point harmonic analysis, the eleventh order harmonics is found to generate an adequate Fourier series expansion for both glazed roofing materials. In addition, there exists a linear relationship between the ambient temperature and the conductive heat transfer for both glazed roofing materials. Based on the gradient of the graphs, lower heat transfer is indicated through polyfilled. Thus polyfilled would have a lower thermal impact compared to polycarbonate.
Percolation induced heat transfer in deep unsaturated zones
Lu, N.; LeCain, G.D.
2003-01-01
Subsurface temperature data from a borehole located in a desert wash were measured and used to delineate the conductive and advective heat transfer regimes, and to estimate the percolation quantity associated with the 1997-1998 El Ni??no precipitation. In an arid environment, conductive heat transfer dominates the variation of shallow subsurface temperature most of the time, except during sporadic precipitation periods. The subsurface time-varying temperature due to conductive heat transfer is highly correlated with the surface atmospheric temperature variation, whereas temperature variation due to advective heat transfer is strongly correlated with precipitation events. The advective heat transfer associated with precipitation and infiltration is the focus of this paper. Disruptions of the subsurface conductive temperature regime, associated with the 1997-1998 El Ni??no precipitation, were detected and used to quantify the percolation quantity. Modeling synthesis using a one-dimensional coupled heat and unsaturated flow model indicated that a percolation per unit area of 0.7 to 1.3 m height of water in two weeks during February 1998 was responsible for the observed temperature deviations down to a depth of 35.2 m. The reported study demonstrated quantitatively, for the first time, that the near surface temperature variation due to advective heat transfer can be significant at a depth greater than 10 m in unsaturated soils and can be used to infer the percolation amount in thick unsaturated soils.
Heat Transfer of Airfoils and Plates
NASA Technical Reports Server (NTRS)
Seibert, Otto
1943-01-01
The few available test data on the heat dissipation of wholly or partly heated airfoil models are compared with the corresponding data for the flat plate as obtained by an extension of Prandtl's momentum theory, with differentiation between laminar and turbulent boundary layer and transitional region between both, the extent and appearance of which depend upon certain critical factors. The satisfactory agreement obtained justifies far-reaching conclusions in respect to other profile forms and arrangements of heated surface areas. The temperature relationship of the material quantities in its effect on the heat dissipation is discussed as far as is possible at tk.e present state of research, and it is shown that the profile drag of heated wing surfaces can increase or decrease with the temperature increase depending upon the momentarily existent structure of the boundary layer.
Nonlinear aspects of high heat flux nucleate boiling heat transfer. Part 1, Formulation
Sadasivan, P.; Unal, C.; Nelson, R.
1994-04-01
This paper outlines the essential details of the formulation and numerical implementation of a model used to study nonlinear aspects of the macrolayer-controlled heat transfer process associated with high heat flux nucleate boiling and the critical heat flux. The model addresses the three-dimensional transient conduction heat transfer process within the problem domain comprised of the macrolayer and heater. Heat dissipation from the heater is modeled as the sum of transient transport into the macrolayer, and the heat loss resulting from evaporation of menisci associated with vapor stems.
Kaji, N. ); Mori, Y.H. ); Tochitani, Y. )
1988-08-01
The heat transfer enhancement caused by the application of a low-frequency (1 {approximately} 16 Hz) alternating field having the sinusoidal waveform has been studied experimentally with water drops in a medium of silicone oil. The heat transfer coefficients has been found to peak at three particular frequencies. The data newly obtained with the sinusoidal waveform are compared with earlier results obained with electric fields having other waveforms. The waveform and the frequency that yield the largest enhancement of heat transfer are sought.
Measurement of heat transfer coefficients by nuclear magnetic resonance.
Gultekin, David H; Gore, John C
2008-11-01
We demonstrate an experimental method for the measurement of heat transfer coefficient for a fluid system by magnetic resonance imaging. In this method, the temporal variation of thermally induced nuclear shielding is monitored and the average heat transfer coefficient is measured as a function of fluid velocity. We examine the cases of natural convection and forced convection at fluid velocity up to 0.8 m s(-1). These cases correspond to low dimensionless Biot (Bi) number where the heat transfer is limited by thermal convection. We demonstrate the NMR method for two simple geometries, a cylinder and a sphere, to experimentally determine the heat transfer coefficient (h) in two NMR imaging and spectroscopy systems through measuring three NMR parameters, the chemical shift, magnetization and spin self diffusion coefficient. PMID:18524523
The measurement of capsule heat transfer gaps using neutron radiography.
NASA Technical Reports Server (NTRS)
Thaler, L. A.
1971-01-01
The use of neutron radiographs to determine dimensional changes of heat transfer gaps in cylindrical nuclear fueled capsules is described. A method was developed which involves scanning a very fine grained neutron radiograph negative with a recording microdensitometer. The output of the densitometer is recorded on graph paper and the heat transfer gap is plotted as a well-defined optical density change. Calibration of the recording microdensitometer ratio arms permits measurements to be made of the heat transfer optical density change from the microdensitometer trace. Total heat transfer gaps, measured by this method, agree with the physical measurements within plus or minus 0.005 cm over a range of gaps from 0.061 to 0.178 cm.
Volume-energy parameters for heat transfer to supercritical fluids
NASA Technical Reports Server (NTRS)
Kumakawa, A.; Niino, M.; Hendricks, R. C.; Giarratano, P. J.; Arp, V. D.
1986-01-01
Reduced Nusselt numbers of supercritical fluids from different sources were grouped by several volume-energy parameters. A modified bulk expansion parameter was introduced based on a comparative analysis of data scatter. Heat transfer experiments on liquefied methane were conducted under near-critical conditions in order to confirm the usefulness of the parameters. It was experimentally revealed that heat transfer characteristics of near-critical methane are similar to those of hydrogen. It was shown that the modified bulk expansion parameter and the Gibbs-energy parameter grouped the heat transfer data of hydrogen, oxygen and methane including the present data on near-critical methane. It was also indicated that the effects of surface roughness on heat transfer were very important in grouping the data of high Reynolds numbers.
Wind heat transfer coefficient in solar collectors in outdoor conditions
Kumar, Suresh; Mullick, S.C.
2010-06-15
Knowledge of wind heat transfer coefficient, h{sub w}, is required for estimation of upward losses from the outer surface of flat plate solar collectors/solar cookers. In present study, an attempt has been made to estimate the wind induced convective heat transfer coefficient by employing unglazed test plate (of size about 0.9 m square) in outdoor conditions. Experiments, for measurement of h{sub w}, have been conducted on rooftop of a building in the Institute campus in summer season for 2 years. The estimated wind heat transfer coefficient has been correlated against wind speed by linear regression and power regression. Experimental values of wind heat transfer coefficient estimated in present work have been compared with studies of other researchers after normalizing for plate length. (author)
Heat Transfer at Supercritical Pressures and the Onset of Deterioration
Kirillov, Pavel L.; Grabezhnaya, Vera A.
2006-07-01
The comparison of the data on heat transfer at supercritical pressures (SCP) demonstrates that they have a considerable spread, which shows a complex nature of the process and a probable inaccuracy in the methods of data processing caused by a sharp change in thermophysical properties near the pseudo-critical point. The recent experimental data at SCP for upward flow of water are compared with some correlations applicable to engineering analysis. The correlations for the onset of heat transfer deterioration against the experimental data were analyzed. The heat transfer deterioration in this data was far from test section inlet The generalization of data on the onset of heat transfer deterioration for various coolants (water, CO{sub 2}, R12) was proposed. (authors)
Navier-Stokes analysis of turbine blade heat transfer
NASA Technical Reports Server (NTRS)
Boyle, R. J.
1990-01-01
Comparisons with experimental heat transfer and surface pressures were made for seven turbine vane and blade geometries using a quasi-three-dimensional thin-layer Navier-Stokes analysis. Comparisons are made for cases with both separated and unseparated flow over a range of Reynolds numbers and freestream turbulence intensities. The analysis used a modified Baldwin-Lomax turbulent eddy viscosity mode. Modifications were made to account for the effects of: (1) freestream turbulence on both transition and leading edge heat transfer; (2) strong favorable pressure gradients on relaminarization; and (3) variable turbulent Prandtl number heat transfer. In addition, the effect of heat transfer on the near wall model of Deissler is compared with the Van Driest model.
Enhancement of laminar convective heat transfer using microparticle suspensions
NASA Astrophysics Data System (ADS)
Zhu, Jiu Yang; Tang, Shiyang; Yi, Pyshar; Baum, Thomas; Khoshmanesh, Khashayar; Ghorbani, Kamran
2016-04-01
This paper investigates the enhancement of convective heat transfer within a sub-millimetre diameter copper tube using Al2O3, Co3O4 and CuO microparticle suspensions. Experiments are conducted at different particle concentrations of 1.0, 2.0 and 5.0 wt% and at various flow rates ranging from 250 to 1000 µl/min. Both experimental measurements and numerical analyses are employed to obtain the convective heat transfer coefficient. The results indicate a significant enhancement in convective heat transfer coefficient due to the implementation of microparticle suspensions. For the case of Al2O3 microparticle suspension with 5.0 wt% concentration, a 20.3 % enhancement in convective heat transfer coefficient is obtained over deionised water. This is comparable to the case of Al2O3 nanofluid at the same concentration. Hence, there is a potential for the microparticle suspensions to be used for cooling of compact integrated systems.
Prediction of Unshsrouded Rotor Blade Tip Heat Transfer
NASA Technical Reports Server (NTRS)
Ameri, A. A.; Steinthorsson, E.
1994-01-01
The rate of heat transfer on the tip of a turbine rotor blade and on the blade surface in the vicinity of the tip, was successfully predicted. The computations were performed with a multiblock computer code which solves the Reynolds Averaged Navier-Stokes equations using an efficient multigrid method. The case considered for the present calculations was the Space Shuttle Main Engine (SSME) high pressure fuel side turbine. The predictions of the blade tip heat transfer agreed reasonably well with the experimental measurements using the present level of grid refinement. On the tip surface, regions with high rate of heat transfer was found to exist close to the pressure side and suction side edges. Enhancement of the heat transfer was also observed on the blade surface near the tip. Further comparison of the predictions was performed with results obtained from correlations based on fully developed channel flow.
Heat transfer characteristics of the metal hydride vessel based on the plate-fin type heat exchanger
NASA Astrophysics Data System (ADS)
Oi, Tsutomu; Maki, Kohei; Sakaki, Yoshinori
Heat transfer characteristics of the metal hydride vessel based on the plate-fin type heat exchanger were investigated. Metal hydride beds were filled with AB 2 type hydrogen-storage alloy's particles, Ti 0.42Zr 0.58Cr 0.78Fe 0.57Ni 0.2Mn 0.39Cu 0.03, with a storage capacity of 0.92 wt.%. Heat transfer model in the metal hydride bed based on the heat transfer mechanism for packed bed proposed by Kunii and co-workers is presented. The time-dependent hydrogen absorption/desorption rate and pressure in the metal hydride vessel calculated by the model were compared with the experimental results. During the hydriding, calculated hydrogen absorption rates agreed with measured ones. Calculated thermal equilibrium hydrogen pressures were slightly lower than the measured hydrogen pressures at the inlet of metal hydride vessel. Taking account of the pressure gradient between the inlet of metal hydride vessel and the metal hydride bed, it is considered that this discrepancy is reasonable. During the dehydriding, there were big differences between the calculated hydrogen desorption rates and measured ones. As calculated hydrogen desorption rates were lower than measured ones, there were big differences between the calculated thermal equilibrium hydrogen pressures and the measured hydrogen pressures at the inlet of metal hydride vessel. It is considered that those differences are due to the differences of the heat transfer characteristics such as thermal conductivity of metal hydride particles and porosity between the assumed and actual ones. It is important to obtain the heat transfer characteristics such as thermal conductivity of metal hydride particles and porosity both during the hydriding and dehydriding to design a metal hydride vessel.
Boyer, B.D.; Parlatan, Y.; Slovik, G.C.; Rohatgi, U.S.
1995-09-01
RELAP5 MOD3.1.1 is being used to simulate Loss of Coolant Accidents (LOCA) for the Simplified Boiling Water Reactor (SBWR) being proposed by General Electric (GE). One of the major components associated with the SBWR is the Passive Containment Cooling System (PCCS) which provides the long-term heat sink to reject decay heat. The RELAP5 MOD3.1.1 code is being assessed for its ability to represent accurately the PCCS. Data from the Phase 1, Step 1 Heat Transfer Tests performed at Toshiba`s Gravity-Driven Integral Full-Height Test for Passive Heat Removal (GIRAFFE) facility will be used for assessing the ability of RELAP5 to model condensation in the presence of noncondensables. The RELAP5 MOD3.1.1 condensation model uses the University of California at Berkeley (UCB) correlation developed by Vierow and Schrock. The RELAP5 code uses this heat transfer coefficient with the gas velocity effect multiplier being limited to 2. This heat transfer option was used to analyze the condensation heat transfer in the GIRAFFE PCCS heat exchanger tubes in the Phase 1, Step 1 Heat Transfer Tests which were at a pressure of 3 bar and had a range of nitrogen partial pressure fractions from 0.0 to 0.10. The results of a set of RELAP5 calculations al these conditions were compared with the GIRAFFE data. The effects of PCCS cell nodings on the heat transfer process were also studied. The UCB correlation, as implemented in RELAP5, predicted the heat transfer to {+-}5% of the data with a three-node model. The three-node model has a large cell in the entrance region which smeared out the entrance effects on the heat transfer, which tend to overpredict the condensation. Hence, the UCB correlation predicts condensation heat transfer in the presence of noncondensable gases with only a coarse mesh. The cell length term in the condensation heat transfer correlation implemented in the code must be removed to allow for accurate calculations with smaller cell sizes.
Particle-water heat transfer during explosive volcanic eruptions
NASA Astrophysics Data System (ADS)
Woodcock, D. C.; Gilbert, J. S.; Lane, S. J.
2012-10-01
Thermal interaction between volcanic particles and water during explosive eruptions has been quantified using a numerical heat transfer model for spherical particles. The model couples intraparticle conduction with heat transfer from the particle surface by boiling water in order to explore heat loss with time for a range of particle diameters. The results are combined with estimates of particle settling times to provide insight into heat removal during eruption from samples of volcanic particles produced by explosive eruption. Heat removal is restricted by resistance to heat transfer from the volcanic particles with intraparticle thermal conduction important for large particles and surface cooling by boiling dominating for small particles. In most cases, volcanic particles approach thermal equilibrium with the surrounding fluid during an explosive eruption. Application of the results to a sample from the Gjálp 1996, Iceland eruption indicates that, relative to 0○C, 70-80% of the heat is transferred from the particles to boiling water during the settling time before burial in the stratigraphic succession. The implication is that, for subglacial explosive eruptions, much of the heat content of the magma is coupled into melting ice extremely rapidly. If all particles of the Gjálp 1996 deposit were cooled to the local boiling point by the end of the eruption then approximately 78% of the initial heat content was removed from the erupting magma during the eruption. This is consistent with calorimetric calculations based on volumes of ice melted during and after the eruption.
Heat transfer intensification by increasing vapor flow rate in flat heat pipes
NASA Astrophysics Data System (ADS)
Sprinceana, Silviu; Mihai, Ioan; Beniuga, Marius; Suciu, Cornel
2015-02-01
Flat heat pipes have various technical applications, one of the most important being the cooling of electronic components[9]. Their continuous development is due to the fact that these devices permit heat transfer without external energetic contribution. The practical exploitation of flat heat pipes however is limited by the fact that dissipated power can only reach a few hundred watts. The present paper aims to advance a new method for the intensification of convective heat transfer. A centrifugal mini impeller, driven by a turntable which incorporates four permanent magnets was designed. These magnets are put in motion by another rotor, which in its turn includes two permanent magnets and is driven by a mini electrical motor. Rotation of the centrifugal blades generates speed and pressure increase of the cooling agent brought to vapor state within the flat micro heat pipe. It's well known that the liquid suffers biphasic transformations during heat transfer inside the heat pipe. Over the hotspot (the heat source being the electronic component) generated at one end of the heat pipe, convective heat transfer occurs, leading to sudden vaporization of the liquid. Pressures generated by newly formed vapors push them towards the opposite end of the flat heat pipe, where a finned mini heat sink is usually placed. The mini-heat exchanger is air-cooled, thus creating a cold spot, where vapors condensate. The proposed method contributes to vapor flow intensification by increasing their transport speed and thus leading to more intense cooling of the heat pipe.
Mesoscopic near-field radiative heat transfer at low temperatures
NASA Astrophysics Data System (ADS)
Maasilta, Ilari; Geng, Zhuoran; Chaudhuri, Saumyadip; Koppinen, Panu
2015-03-01
Near-field radiative heat transfer has mostly been discussed at room temperatures and/or macroscopic scale geometries. Here, we discuss our recent theoretical and experimental advances in understanding near-field transfer at ultra-low temperatures below 1K. As the thermal wavelengths increase with lowering temperature, we show that with sensitive tunnel junction bolometers it is possible to study near-field transfer up to distances ~ 10 μm currently, even though the power levels are low. In addition, these type of experiments correspond to the extreme near-field limit, as the near-field region starts at ~ mm distances at 0.1 K, and could have theoretical power enhancement factors of the order of 1010. Preliminary results on heat transfer between two parallel metallic wires are presented. We also comment on possible areas were such heat transfer might be relevant, such as densely packed arrays of low-temperature detectors.
Comparison of Methods for Calculating Radiative Heat Transfer
Schock, Alfred; Abbate, M J
2012-01-19
Various approximations for calculating radioactive heat transfer between parallel surfaces are evaluated. This is done by applying the approximations based on total emissivities to a special case of known spectral emissivities, for which exact heat transfer calculations are possible. Comparison of results indicates that the best approximation is obtained by basing the emissivity of the receiving surface primarily on the temperature of the emitter. A specific model is shown to give excellent agreement over a very wide range of values.
Enhanced heat transfer in partially-saturated hydrothermal systems
Bixler, N.E.; Carrigan, C.R.
1986-01-01
The role of capillarity is potentially important for determining heat transfer in hydrothermal regions. Capillarity allows mixing of phases in liquid/vapor systems and results in enhanced two-phase convection. Comparisons involving a numerical model with capillarity and analytical models without indicate that heat transfer can be enhanced by about an order of magnitude. Whether capillarity can be important for a particular hydrothermal region will depend on the nature of mineral precipitation as well as pore and fracture size distributions.
Heat transfer from fail-safe magnetorheological fluid dampers
NASA Astrophysics Data System (ADS)
Dogruoz, M. Baris; Gordaninejad, Faramarz; Wang, Eric L.; Stipanovich, Arthur J.
2001-07-01
This study focuses on an experimental study of heat transfer from magneto-rheological fluid (MRF) dampers. Two semi- active automotive size MRF dampers, one with fins and the other without fins, were constructed and tested. The experimental results were compared with those of a previously developed theoretical model. It is demonstrate that especially at high peak velocities, the temperature rise is significant and heat transfer from these devices can be enhanced considerably by utilizing fins.
One dimensional lunar ash flow with and without heat transfer
NASA Technical Reports Server (NTRS)
Pai, S. I.; Hsieh, T.
1971-01-01
The characteristics of lunar ash flow are discussed in terms of the two phase flow theory of a mixture of a gas and small solid particles. A model is developed to present the fundamental equations and boundary conditions. Numerical solutions for special ash flow with and without heat transfer are presented. In the case of lunar ash flow with small initial velocity, the effect of the heat transfer makes the whole layer of ash flow more compacted together than the corresponding isothermal case.
Advanced turbine cooling, heat transfer, and aerodynamic studies
Je-Chin Han; Schobeiri, M.T.
1995-10-01
The contractual work is in three parts: Part I - Effect of rotation on enhanced cooling passage heat transfer, Part II - Effect on Thermal Barrier Coating (TBC) spallation on surface heat transfer, and Part III - Effect of surface roughness and trailing edge ejection on turbine efficiency under unsteady flow conditions. Each section of this paper has been divided into three parts to individually accommodate each part. Part III is further divided into Parts IIIa and IIIb.
High-Power Liquid-Metal Heat-Transfer Loop
NASA Technical Reports Server (NTRS)
Bhandari, Pradeep; Fujita, Toshio
1991-01-01
Proposed closed-loop system for transfer of thermal power operates at relatively high differential pressure between vapor and liquid phases of liquid-metal working fluid. Resembles "capillary-pumped" liquid-metal heat-transfer loop except electric field across permselective barrier of beta alumina keeps liquid and vapor separate at heat-input end. Increases output thermal power, contains no moving parts, highly reliable and well suited to long-term unattended operation.
A Comparative Study of Heat Transfer in Metallic Materials
NASA Astrophysics Data System (ADS)
Pǎucǎ, Adina; Hepuţ, Teodor; Pinca-Bretotean, Camelia; Stoica, Diana
2011-09-01
Rolling of metallic materials with heat transfer occurs as a result of interaction between the workpiece and the rolling cylinders incandescent. Heat transferred by diffusion into the cylinders generates variable temperature fields. These fields produce variable temperature thermal stress in each rotation cycle of rolling cylinders. This paper aims at mathematical modeling of variable temperature fields, using Matlab. These diagrams obtained are compared with those obtained following experimental study of the thermal lamination cylinders for 5 states isochronous temperature.
Boiling heat transfer on meshed surfaces of different aperture
NASA Astrophysics Data System (ADS)
Orman, Łukasz J.
2014-08-01
The paper presents the results of investigations of the impact of mesh aperture on boiling heat transfer. The tests have been performed for distilled water and ethyl alcohol at ambient pressure. It was observed that the meshed surfaces performed much better than the smooth reference surface and that meshes of smaller aperture provided better results. The obtained results have been compared with selected models of boiling heat transfer from literature.
Code for Multiblock CFD and Heat-Transfer Computations
NASA Technical Reports Server (NTRS)
Fabian, John C.; Heidmann, James D.; Lucci, Barbara L.; Ameri, Ali A.; Rigby, David L.; Steinthorsson, Erlendur
2006-01-01
The NASA Glenn Research Center General Multi-Block Navier-Stokes Convective Heat Transfer Code, Glenn-HT, has been used extensively to predict heat transfer and fluid flow for a variety of steady gas turbine engine problems. Recently, the Glenn-HT code has been completely rewritten in Fortran 90/95, a more object-oriented language that allows programmers to create code that is more modular and makes more efficient use of data structures. The new implementation takes full advantage of the capabilities of the Fortran 90/95 programming language. As a result, the Glenn-HT code now provides dynamic memory allocation, modular design, and unsteady flow capability. This allows for the heat-transfer analysis of a full turbine stage. The code has been demonstrated for an unsteady inflow condition, and gridding efforts have been initiated for a full turbine stage unsteady calculation. This analysis will be the first to simultaneously include the effects of rotation, blade interaction, film cooling, and tip clearance with recessed tip on turbine heat transfer and cooling performance. Future plans call for the application of the new Glenn-HT code to a range of gas turbine engine problems of current interest to the heat-transfer community. The new unsteady flow capability will allow researchers to predict the effect of unsteady flow phenomena upon the convective heat transfer of turbine blades and vanes. Work will also continue on the development of conjugate heat-transfer capability in the code, where simultaneous solution of convective and conductive heat-transfer domains is accomplished. Finally, advanced turbulence and fluid flow models and automatic gridding techniques are being developed that will be applied to the Glenn-HT code and solution process.
Application of ray tracing in radiation heat transfer
NASA Technical Reports Server (NTRS)
Baumeister, Joseph F.
1993-01-01
This collection of presentation figures displays the capabilities of ray tracing for radiation propagation calculations as compared to an analytical approach. The goal is to introduce the terminology and solution process used in ray tracing, and provide insight into radiation heat transfer principles and analysis tools. A thermal analysis working environment is introduced that solves demanding radiation heat transfer problems based on ray tracing. This information may serve as a reference for designing and building ones own analysis environment.
Effect of radiation heat transfer on thermal diffusivity measurements
NASA Astrophysics Data System (ADS)
Araki, N.
1990-03-01
Experimental data on thermal conductivity and thermal diffusivity of a semitransparent material generally include an error due to the radiation heat transfer. This error varies in accordance with the experimental conditions such as the temperature level of the sample and the measuring method. In this paper, research on the influence of radiation heat transfer on thermal diffusivity are reviewed, and as an example, the method to correct the radiation component in the apparent thermal diffusivity measured by the stepwise heating technique is presented. The transient heat transfer by simultaneous thermal conduction and radiation in a semitransparent material is analyzed when the front surface is subjected to stepwise heating. The apparent thermal diffusivity, which includes the radiation component, is calculated for various parameters.
Heat Transfer to Longitudinal Laminar Flow Between Cylinders
NASA Technical Reports Server (NTRS)
Sparrow, Ephraim M.; Loeffler, Albert L. Jr.; Hubbard, H. A.
1960-01-01
Consideration is given to the fully developed heat transfer characteristics for longitudinal laminar flow between cylinders arranged in an equilateral triangular array. The analysis is carried out for the condition of uniform heat transfer per unit length. Solutions are obtained for the temperature distribution, and from these, Nusselt numbers are derived for a wide range of spacing-to-diameter ratios. It is found that as the spacing ratio increases, so also does the wall-to-bulk temperature difference for a fixed heat transfer per unit length. Corresponding to a uniform surface temperature around the circumference of a cylinder, the circumferential variation of the local heat flux is computed. For spacing ratios of 1.5 - 2.0 and greater, uniform peripheral wall temperature and uniform peripheral heat flux are simultaneously achieved. A simplified analysis which neglects circumferential variations is also carried out, and the results are compared with those from the more exact formulation.
Numerical Modeling of Conjugate Heat Transfer in Fluid Network
NASA Technical Reports Server (NTRS)
Majumdar, Alok
2004-01-01
Fluid network modeling with conjugate heat transfer has many applications in Aerospace engineering. In modeling unsteady flow with heat transfer, it is important to know the variation of wall temperature in time and space to calculate heat transfer between solid to fluid. Since wall temperature is a function of flow, a coupled analysis of temperature of solid and fluid is necessary. In cryogenic applications, modeling of conjugate heat transfer is of great importance to correctly predict boil-off rate in propellant tanks and chill down of transfer lines. In TFAWS 2003, the present author delivered a paper to describe a general-purpose computer program, GFSSP (Generalized Fluid System Simulation Program). GFSSP calculates flow distribution in complex flow circuit for compressible/incompressible, with or without heat transfer or phase change in all real fluids or mixtures. The flow circuit constitutes of fluid nodes and branches. The mass, energy and specie conservation equations are solved at the nodes where as momentum conservation equations are solved at the branches. The proposed paper describes the extension of GFSSP to model conjugate heat transfer. The network also includes solid nodes and conductors in addition to fluid nodes and branches. The energy conservation equations for solid nodes solves to determine the temperatures of the solid nodes simultaneously with all conservation equations governing fluid flow. The numerical scheme accounts for conduction, convection and radiation heat transfer. The paper will also describe the applications of the code to predict chill down of cryogenic transfer line and boil-off rate of cryogenic propellant storage tank.
Experimental and numerical investigation of HyperVapotron heat transfer
NASA Astrophysics Data System (ADS)
Wang, Weihua; Deng, Haifei; Huang, Shenghong; Chu, Delin; Yang, Bin; Mei, Luoqin; Pan, Baoguo
2014-12-01
The divertor first wall and neutral beam injection (NBI) components of tokamak devices require high heat flux removal up to 20-30 MW m-2 for future fusion reactors. The water cooled HyperVapotron (HV) structure, which relies on internal grooves or fins and boiling heat transfer to maximize the heat transfer capability, is the most promising candidate. The HV devices, that are able to transfer large amounts of heat (1-20 MW m-2) efficiently, have therefore been developed specifically for this application. Until recently, there have been few attempts to observe the detailed bubble characteristics and vortex evolvement of coolant flowing inside their various parts and understand of the internal two-phase complex heat transfer mechanism behind the vapotron effect. This research builds the experimental facilities of HyperVapotron Loop-I (HVL-I) and Pressure Water HyperVapotron Loop-II (PWHL-II) to implement the subcooled boiling principle experiment in terms of typical flow parameters, geometrical parameters of test section and surface heat flux, which are similar to those of the ITER-like first wall and NBI components (EAST and MAST). The multiphase flow and heat transfer phenomena on the surface of grooves and triangular fins when the subcooled water flowed through were observed and measured with the planar laser induced fluorescence (PLIF) and high-speed photography (HSP) techniques. Particle image velocimetry (PIV) was selected to reveal vortex formation, the flow structure that promotes the vapotron effect during subcooled boiling. The coolant flow data for contributing to the understanding of the vapotron phenomenon and the assessment of how the design and operational conditions that might affect the thermal performance of the devices were collected and analysed. The subcooled flow boiling model and methods of HV heat transfer adopted in the considered computational fluid dynamics (CFD) code were evaluated by comparing the calculated wall temperatures with the
Thin film instabilities on heated substrates: conjugate heat transfer
NASA Astrophysics Data System (ADS)
Dallaston, Michael; Tseluiko, Dmitri; Kalliadasis, Serafim
2015-11-01
Heat transported from a surface by a thin coating film of liquid is greatly affected by instabilities on the free surface of the film. If the solid substrate is heated above the ambient temperature, the hydrodynamic instability of the flow at sufficiently large Reynolds number is exacerbated by Marangoni stresses that result due to the temperature gradient in the fluid. Most studies of this phenomenon assume constant temperature or heat flux at the wall. Here we discuss the less-studied but more realistic situation in which the heat flow within the liquid film is coupled to conduction within the solid substrate, which has a complicated effect on the stability of the free surface. Analytical progress is made possible by linear stability analysis and low-dimensional nonlinear evolution equations derived using a weighted residual method.
Revealing the complex conduction heat transfer mechanism of nanofluids.
Sergis, A; Hardalupas, Y
2015-12-01
Nanofluids are two-phase mixtures consisting of small percentages of nanoparticles (sub 1-10 %vol) inside a carrier fluid. The typical size of nanoparticles is less than 100 nm. These fluids have been exhibiting experimentally a significant increase of thermal performance compared to the corresponding carrier fluids, which cannot be explained using the classical thermodynamic theory. This study deciphers the thermal heat transfer mechanism for the conductive heat transfer mode via a molecular dynamics simulation code. The current findings are the first of their kind and conflict with the proposed theories for heat transfer propagation through micron-sized slurries and pure matter. The authors provide evidence of a complex new type of heat transfer mechanism, which explains the observed abnormal heat transfer augmentation. The new mechanism appears to unite a number of popular speculations for the thermal heat transfer mechanism employed by nanofluids as predicted by the majority of the researchers of the field into a single one. The constituents of the increased diffusivity of the nanoparticle can be attributed to mismatching of the local temperature profiles between parts of the surface of the solid and the fluid resulting in increased local thermophoretic effects. These effects affect the region surrounding the solid manifesting interfacial layer phenomena (Kapitza resistance). In this region, the activity of the fluid and the interactions between the fluid and the nanoparticle are elevated. Isotropic increased nanoparticle mobility is manifested as enhanced Brownian motion and diffusion effects. PMID:26058515
Revealing the complex conduction heat transfer mechanism of nanofluids
NASA Astrophysics Data System (ADS)
Sergis, A.; Hardalupas, Y.
2015-06-01
Nanofluids are two-phase mixtures consisting of small percentages of nanoparticles (sub 1-10 %vol) inside a carrier fluid. The typical size of nanoparticles is less than 100 nm. These fluids have been exhibiting experimentally a significant increase of thermal performance compared to the corresponding carrier fluids, which cannot be explained using the classical thermodynamic theory. This study deciphers the thermal heat transfer mechanism for the conductive heat transfer mode via a molecular dynamics simulation code. The current findings are the first of their kind and conflict with the proposed theories for heat transfer propagation through micron-sized slurries and pure matter. The authors provide evidence of a complex new type of heat transfer mechanism, which explains the observed abnormal heat transfer augmentation. The new mechanism appears to unite a number of popular speculations for the thermal heat transfer mechanism employed by nanofluids as predicted by the majority of the researchers of the field into a single one. The constituents of the increased diffusivity of the nanoparticle can be attributed to mismatching of the local temperature profiles between parts of the surface of the solid and the fluid resulting in increased local thermophoretic effects. These effects affect the region surrounding the solid manifesting interfacial layer phenomena (Kapitza resistance). In this region, the activity of the fluid and the interactions between the fluid and the nanoparticle are elevated. Isotropic increased nanoparticle mobility is manifested as enhanced Brownian motion and diffusion effects
Unsteady heat transfer measurements on a rotating gas turbine blade
NASA Astrophysics Data System (ADS)
Hilditch, M. A.; Ainsworth, R. W.
1990-06-01
This paper presents heat transfer measurements made on the rotor blade of a full-stage model turbine operating at engine representative conditions. The measurement technique of mounting thin film heat transfer gauges on enamel-coated turbine blades enables the heat transfer rate to be measured across a frequency range of dc to 100 KHz. A calibration experiment in which the gauge is pulsed with a laser beam is described in detail. The results are compared with data from a previous 2D simulation of wake-passing flow in the midheight section of the same blade. The mean heat transfer rate recorded in the two experiments shows reasonable agreement. Fluctuations in the unsteady heat transfer signal at nozzle-guide-vane passing frequency are seen at the same locations in data from both experiments. The magnitude of the fluctuations seen on the rotor are much smaller than those recorded in the 2D simulation. Frequency spectra and correlation analysis of heat transfer traces recorded on the rotor are also presented.
Heat Transfer Modeling for Rigid High-Temperature Fibrous Insulation
NASA Technical Reports Server (NTRS)
Daryabeigi, Kamran; Cunnington, George R.; Knutson, Jeffrey R.
2012-01-01
Combined radiation and conduction heat transfer through a high-temperature, high-porosity, rigid multiple-fiber fibrous insulation was modeled using a thermal model previously used to model heat transfer in flexible single-fiber fibrous insulation. The rigid insulation studied was alumina enhanced thermal barrier (AETB) at densities between 130 and 260 kilograms per cubic meter. The model consists of using the diffusion approximation for radiation heat transfer, a semi-empirical solid conduction model, and a standard gas conduction model. The relevant parameters needed for the heat transfer model were estimated from steady-state thermal measurements in nitrogen gas at various temperatures and environmental pressures. The heat transfer modeling methodology was evaluated by comparison with standard thermal conductivity measurements, and steady-state thermal measurements in helium and carbon dioxide gases. The heat transfer model is applicable over the temperature range of 300 to 1360 K, pressure range of 0.133 to 101.3 x 10(exp 3) Pa, and over the insulation density range of 130 to 260 kilograms per cubic meter in various gaseous environments.
High Reynolds Number and Turbulence Effects on Turbine Heat Transfer
NASA Technical Reports Server (NTRS)
Yeh, Frederick C.; Hippensteele, Steven A.; vanFossen, G. James; Poinsatte, Philip E.; Ameri, Ali
1994-01-01
Experimental data on pressure distribution and heat transfer on a turbine airfoil were obtained over a range of Reynolds numbers from 0.75 to 7.0 x 10(exp 6) and a range of turbulence intensities from 1.8 to about 15%. The purpose of this study was to obtain fundamental heat transfer and pressure distribution data over a wide range of high Reynolds numbers and to extend the heat transfer data base to include the range or Reynolds numbers encountered in the Space Shuttle main engine turbopump turbines. The results of this study indicated that Reynolds number and turbulence intensity have a large effect on both the transition from laminar to turbulent flow and the resulting heat transfer. For a given turbulence intensity, heat transfer for all Reynolds numbers at the leading edge can generally be correlated with the Frossling number developed for lower Reynolds numbers. For a given turbulence intensity, heat transfer for the airfoil surfaces downstream of the leading edge can be approximately correlated with a dimensionless parameter. Comparisons of the experimental results were also made with a numerical solution from a two-dimensional Navier-Stokes code.
Spinodal turbulence enhances heat transfer in micro devices
NASA Astrophysics Data System (ADS)
Farisé, Stefano; Poesio, Pietro; Beretta, Gian Paolo
2012-11-01
We experimentally prove the possibility of using spinodal mixtures to increase heat transfer in micro devices as a consequence of an evenly distributed micro agitation, which increases the effective diffusivity. Despite the Re -number is as low as 5, turbulence-like mixing can be achieved by mass transfer effects. A mixture of acetone-hexadecane is quenched in a micro heat exchanger to induce spinodal decomposition. The heat transfer rate is enhanced by self-induced convective motion (spinodal turbulence) because the drops of one phase move against each others under the influence of non-equilibrium capillary forces, Korteweg stresses,which are sustained by the free energy liberated during phase separation. The heat transfer is increased up to the 200% and the effect become larger as the bulk Re decreses, while no dramatic increase in the pressure drop is observed. We built two different experimental set-ups: in the first we measure the heat transfer with a feedback method and in the second we measure the pressure drop and we visualize the induced convection. High-speed camera visualization,pressure drop and temperature measurements allow a complete characterization of the phenomenon, with a special attention to the quantification of the heat transfer coefficent enhancement.
Literature survey of heat transfer enhancement techniques in refrigeration applications
Jensen, M.K.; Shome, B.
1994-05-01
A survey has been performed of the technical and patent literature on enhanced heat transfer of refrigerants in pool boiling, forced convection evaporation, and condensation. Extensive bibliographies of the technical literature and patents are given. Many passive and active techniques were examined for pure refrigerants, refrigerant-oil mixtures, and refrigerant mixtures. The citations were categorized according to enhancement technique, heat transfer mode, and tube or shell side focus. The effects of the enhancement techniques relative to smooth and/or pure refrigerants were illustrated through the discussion of selected papers. Patented enhancement techniques also are discussed. Enhanced heat transfer has demonstrated significant improvements in performance in many refrigerant applications. However, refrigerant mixtures and refrigerant-oil mixtures have not been studied extensively; no research has been performed with enhanced refrigerant mixtures with oil. Most studies have been of the parametric type; there has been inadequate examination of the fundamental processes governing enhanced refrigerant heat transfer, but some modeling is being done and correlations developed. It is clear that an enhancement technique must be optimized for the refrigerant and operating condition. Fundamental processes governing the heat transfer must be examined if models for enhancement techniques are to be developed; these models could provide the method to optimize a surface. Refrigerant mixtures, with and without oil present, must be studied with enhancement devices; there is too little known to be able to estimate the effects of mixtures (particularly NARMs) with enhanced heat transfer. Other conclusions and recommendations are offered.
Sliding bubble dynamics and the effects on surface heat transfer
NASA Astrophysics Data System (ADS)
Donnelly, B.; Robinson, A. J.; Delauré, Y. M. C.; Murray, D. B.
2012-11-01
An investigation into the effects of a single sliding air bubble on heat transfer from a submerged, inclined surface has been undertaken. Existing literature has shown that both vapour and gas bubbles can increase heat transfer rates from adjacent heated surfaces. However, the mechanisms involved are complex and dynamic and in some cases poorly understood. The present study utilises high speed, high resolution, infrared thermography and video photography to measure two dimensional surface heat transfer and three dimensional bubble position and shape. This provides a unique insight into the complex interactions at the heated surface. Bubbles of volume 0.05, 0.1, 0.2 and 0.4 ml were released onto a surface inclined at 30 degrees to horizontal. Results confirmed that sliding bubbles can enhance heat transfer rates up to a factor of 9 and further insight was gained about the mechanisms behind this phenomenon. The enhancement effects were observed over large areas and persisted for a long duration with the bubble exhibiting complex shape and path oscillations. It is believed that the periodic wake structure present behind the sliding bubble affects the bubble motion and is responsible for the heat transfer effects observed. The nature of this wake is proposed to be that of a chain of horseshoe vortices.
Heat Transfer and Flow Structure Evaluation of a Synthetic Jet Emanating from a Planar Heat Sink
NASA Astrophysics Data System (ADS)
Manning, Paul; Persoons, Tim; Murray, Darina
2014-07-01
Direct impinging synthetic jets are a proven method for heat transfer enhancement, and have been subject to extensive research. However, despite the vast amount of research into direct synthetic jet impingement, there has been little research investigating the effects of a synthetic jet emanating from a heated surface, this forms the basis of the current research investigation. Both single and multiple orifices are integrated into a planar heat sink forming a synthetic jet, thus allowing the heat transfer enhancement and flow structures to be assessed. The heat transfer analysis highlighted that the multiple orifice synthetic jet resulted in the greatest heat transfer enhancements. The flow structures responsible for these enhancements were identified using a combination of flow visualisation, thermal imaging and thermal boundary layer analysis. The flow structure analysis identified that the synthetic jets decreased the thermal boundary layer thickness resulting in a more effective convective heat transfer process. Flow visualisation revealed entrainment of local air adjacent to the heated surface; this occurred from vortex roll-up at the surface of the heat sink and from the highly sheared jet flow. Furthermore, a secondary entrainment was identified which created a surface impingement effect. It is proposed that all three flow features enhance the heat transfer characteristics of the system.
NASA Astrophysics Data System (ADS)
Wang, Yiping; Li, Shuai; Yang, Xue; Deng, Yadong; Su, Chuqi
2016-03-01
For vehicle thermoelectric exhaust energy recovery, the temperature difference between the heat exchanger and the coolant has a strong influence on the electric power generation, and ribs are often employed to enhance the heat transfer of the heat exchanger. However, the introduction of ribs will result in a large unwanted pressure drop in the exhaust system which is unfavorable for the engine's efficiency. Therefore, how to enhance the heat transfer and control the pressure drop in the exhaust system is quite important for thermoelectric generators (TEG). In the current study, a symmetrical arrangement of dimpled surfaces staggered in the upper and lower surfaces of the heat exchanger was proposed to augment heat transfer rates with minimal pressure drop penalties. The turbulent flow characteristics and heat transfer performance of turbulent flow over the dimpled surface in a flat heat exchanger was investigated by numerical simulation and temperature measurements. The heat transfer capacity in terms of Nusselt number and the pressure loss in terms of Fanning friction factors of the exchanger were compared with those of the flat plate. The pressure loss and heat transfer characteristics of dimples with a depth-to-diameter ratio ( h/D) at 0.2 were investigated. Finally, a quite good heat transfer performance with minimal pressure drop heat exchanger in a vehicle TEG was obtained. And based on the area-averaged surface temperature of the heat exchanger and the Seeback effect, the power generation can be improved by about 15% at Re = 25,000 compared to a heat exchanger with a flat surface.
Rocket engine heat transfer and material technology for commercial applications
NASA Technical Reports Server (NTRS)
Hiltabiddle, J.; Campbell, J.
1974-01-01
Liquid fueled rocket engine combustion, heat transfer, and material technology have been utilized in the design and development of compact combustion and heat exchange equipment intended for application in the commercial field. An initial application of the concepts to the design of a compact steam generator to be utilized by electrical utilities for the production of peaking power is described.
Instabilities encountered during heat transfer to a supercritical fluid
NASA Technical Reports Server (NTRS)
Cornelius, A. J.
1969-01-01
Investigation was made of the unstable behavior of a heat-transfer loop operating at a supercritical pressure. Natural convection operation of the loop, with observations on acoustic and slow oscillatory behavior, was emphasized during testing. The basic cause of both types of behavior appeared to originate in the heated boundary layer.
Heat Transfer from Finned Metal Cylinders in an Air Stream
NASA Technical Reports Server (NTRS)
Biermann, Arnold, E; Pinkel, Benjamin
1935-01-01
This report presents the results of tests made to supply design information for the construction of metal fins for the cooling of heated cylindrical surfaces by an air stream. A method is given for determining fin dimensions for a maximum heat transfer with the expenditure of a given amount of material for a variety of conditions of air flow and metals.
Thin-film gage measures low heat-transfer rates
NASA Technical Reports Server (NTRS)
Spitzer, C. R.
1966-01-01
Low heat-transfer gage facilitates determination of the transition between laminar and turbulent conditions, in the boundary layer surrounding slender and moderately slender cones under test in a hypersonic blowdown helium tunnel. The gage consists of a thin layer of vacuum-evaporated platinum on a heat resistant glass substrate contoured to fit model surfaces.
Students' Misconceptions about Heat Transfer Mechanisms and Elementary Kinetic Theory
ERIC Educational Resources Information Center
Pathare, S. R.; Pradhan, H. C.
2010-01-01
Heat and thermodynamics is a conceptually rich area of undergraduate physics. In the Indian context in particular there has been little work done in this area from the point of view of misconceptions. This prompted us to undertake a study in this area. We present a study of students' misconceptions about heat transfer mechanisms, i.e. conduction,…
NASA Astrophysics Data System (ADS)
Piasecka, Magdalena; Strąk, Kinga
2016-03-01
The aim of the paper is to estimate effect of the heating surface enhancement on FC-72 flow boiling heat transfer for a vertical minichannel 1.7 mm deep, 24 mm wide and 360 mm long. Two types of enhanced heating surfaces were used: one with minicavities distributed unevenly, and the other with capillary metal fibrous structure. It was to measure temperature field on the plain side of the heating surface by means of the infrared thermography and to observe the two-phase flow patterns on the enhanced foil side. The paper analyses mainly the impact of the microstructured heating surface on the heat transfer coefficient. The results are presented as heat transfer coefficient dependences on the distance along the minichannel length. The data obtained using two types of enhanced heating surfaces in experiments was compared with the data when smooth foil as the heating surface was used. The highest local values of heat transfer coefficient were obtained using enhanced foil with minicavities - in comparison to other cases. Local values of heat transfer coefficient received for capillary fibrous structure were the lowest, even compared with data obtained for smooth foil. Probably this porous structure caused local flow disturbances.
The transference of heat from a hot plate to an air stream
NASA Technical Reports Server (NTRS)
Elias, Franz
1931-01-01
The object of the present study was to define experimentally the field of temperature and velocity in a heated flat plate when exposed to an air stream whose direction is parallel to it, then calculate therefrom the heat transference and the friction past the flat plate, and lastly, compare the test data with the mathematical theory. To ensure comparable results, we were to actually obtain or else approximate: a) two-dimensional flow; b) constant plate temperature in the direction of the stream. To approximate the flow in two dimensions, we chose a relatively wide plate and measured the velocity and temperature in the median plane.
Boiling Heat Transfer Experiments by using Transparent Heated Microtube
NASA Astrophysics Data System (ADS)
Huang, Shih-Che; Kawanami, Osamu; Kawakami, Kazunari; Honda, Itsuro; Kawashima, Yousuke; Ohta, Haruhiko
For detailed study of the relationship between boiling bubble behavior and inner wall temperature during flow boiling in microtubes, a transparent heated microtube, whose inner wall was coated with a thin gold film, was employed. Boiling behavior could be observed clearly, and the inner wall temperature of the tube was measured simultaneously with direct heating of the film. Ionized water was used as a test fluid. The experimental conditions were as follows: tube diameter, 1 mm; inlet liquid subcooling, 10 K; mass velocity, 100 kg/m2s and heat flux, up to 469 kW/m2 in the open system. As a result, the frequencies of fluctuation of the inner wall temperature and flow rate were divided into four regions. In addition, the fluctuation range of flow rate increased with increasing heat flux however, this fluctuation decreased drastically for heat flux over 212 kW/m2. The fluctuation of void fraction coincided with that of inner wall temperature.
Cho, D.H.; Page, R.J.; Hurtault, D.; Abdulla, S.; Liu, X.; Anderson, M.H.; Bonazza, R.; Corradini, M.
2002-02-26
Experiments on direct-contact heat exchange between molten metal and water for steam production were conducted. These experiments involved the injection of water into molten lead-bismuth eutectic for heat transfer measurements in a 1-D geometry. Based on the initial results of the experiments, the effects of the water flow rate and the molten metal superheat (temperature difference between molten metal and saturated water) on the volumetric heat transfer coefficient were discussed.
The influence of oil on nucleate pool boiling heat transfer
NASA Astrophysics Data System (ADS)
Spindler, Klaus; Hahne, Erich
2009-05-01
The influence of various oil contents in R134a is investigated for nucleate pool boiling on copper tubes either sandblasted or with enhanced heating surfaces (GEWA-B tube). Polyolester oils (POE) (Reniso Triton) with medium viscosity 55 cSt (SE55) and high viscosity 170 cSt (SE170) were used. Heat transfer coefficients were obtained for boiling temperatures between -28.6 and +20.1°C. The oil content varied from 0 to 5% mass fraction. For the sandblasted tube and the SE55 oil the heat transfer coefficients for the refrigerant/oil-mixture can be higher or lower than those for the pure refrigerant, depending on oil mass fraction, boiling temperature and heat flux. In some cases the highest heat transfer coefficients were obtained at a mass fraction of 3%. For the 170 cSt oil there is a clear decrease in heat transfer for all variations except for a heat flux 4,000 W/m2 and -10.1°C at 0.5% oil content. The heat transfer coefficients are compared to those in the literature for a smooth stainless steel tube and a platinum wire. For the enhanced tube and 55 cSt oil the heat transfer coefficients are clearly below those for pure refrigerant in all cases. The experimental results for the sandblasted tube are compared with the correlation by Jensen and Jackman. The calculated values are within +20 and -40% for the medium viscosity oil and between +50% and -40% for the high viscosity oil. A correlation for predicting oil-degradation effects on enhanced surfaces does not exist.
NASA Technical Reports Server (NTRS)
Nealy, D. A.; Mihelc, M. S.; Hylton, L. D.; Gladden, H. J.
1983-01-01
The results of an experimental study of aerodynamic (surface velocity) and heat transfer distributions over the surfaces of two different, highly loaded, low-solidity contemporary turbine vane designs are presented. The aerodynamic configurations of the two vanes were carefully selected to emphasize fundamental differences in the character of the solution surface pressure distributions and the consequent effect on surface heat transfer distributions. The experimental measurements were made in moderate-temperature, three-vane cascades under steady-state conditions. The principal independent parameters (Mach number, Reynolds number, turbulence intensity, and wall-to-gas temperature ratio) were varied over ranges consistent with actual engine operation, and the heat matrix was structured to provide an assessment of the independent influence of each parameter. These measurements are intended to serve as verification data for a parallel analytical code development effort. The results of this parallel effort are briefly reviewed, and the principal conclusions to date are summarized.
Evaluation of Heat Transfer Augmentation in a Nanofluid-Cooled Microchannel Heat Sink
NASA Astrophysics Data System (ADS)
Abbassi, Hessamoddin; Aghanajafi, Cyrus
2006-12-01
Present investigation deals with appraising heat transfer enhancement of single phase microchannel heat sink (MCHS) by ultra fine Cu particle incorporation in base coolant fluid. The particle diameter is of nanometer size and base fluid in combination of nanoparticles is called nanofluid. Governing equations for fluid flow and heat transfer are based on well established "porous medium model" and accordingly, modified Darcy equation and two-equation model are employed. Appropriate equations for both fluid flow and heat transfer are derived and cast into dimensionless form. Velocity profile is obtained analytically and in order to solve conjugate heat transfer problem a combined analytical-numerical approach is employed. For heat transfer analysis, thermal dispersion model is adopted and latest proposed model for effective thermal conductivity - which considers the salient effect of interfacial shells between particles and base fluid - is integrated into model. The effects of dispersed particles concentration, thermal dispersion coefficient and Reynolds number are investigated on thermal fields and on thermal performance of MCHS. Additionally, the impact of turbulent heat transfer on heat transfer enhancement is considered.
Forced Convection Heat Transfer of Liquid Hydrogen Through a 200-mm Long Heated Tube
NASA Astrophysics Data System (ADS)
Tatsumoto, Hideki; Shirai, Yasuyuki; Shiotsu, Masahiro; Hata, Koichi; Naruo, Yoshihiro; Kobayashi, Hiroaki; Inatani, Yoshifumi; Kinoshita, Katsuhiro
The heat transfer from the inner side of a vertically- mounted heated tube with a length of 200.0 mm and a diameter of 6.0 mm to a forced flow of liquid hydrogen was measured for wide ranges of flow rate and liquid temperature. The non-boiling heat transfer coefficients agreed well with the Dittus -Boelter equation. The heat fluxes at departure from nucleate boiling (DNB) were higher for higher flow velocities and greater subcooling. The effect of the tube length on the DNB heat flux was clarified through comparison with our previous data. It was confirmed that the experimental data agreed well with the authors' DNB correlation.
Fiebig, M.; Chen, Y.; Grosse-Gorgemann, A.; Mitra, N.K.
1995-08-01
Numerical investigations of three-dimensional flow and heat transfer in a finned tube with punched longitudinal vortex generators (LVG`s) are carried out for Reynolds number of 250 and 300. Air with a Prandtl number of 0.7 is used as the fluid. The flow is both thermally and hydrodynamically developing. The LVG is a delta winglet pair (DWP) punched out of the fin and is located directly behind the tube, symmetrically separated by one tube diameter. The DWP generates longitudinal vortices in the wake of the tube, defers flow separation on the tube, deflects the main stream into the tube wake, and strong reduces the ``dead water zone.`` Heat transfer reversal is avoided by the DWP. Comparison of the span-averaged Nusselt numbers for the fin with and without DWP shows significant local heat transfer enhancement of several hundred percent in the tube wake. For Re = 300 and Fi = 200 the global heat transfer augmentation by a DWP, which amounts to only 2.5% of the fin area, is 31%.
Finite Element Heat & Mass Transfer Code
1996-10-10
FEHM is a numerical simulation code for subsurface transport processes. It models 3-D, time-dependent, multiphase, multicomponent, non-isothermal, reactive flow through porous and fractured media. It can accurately represent complex 3-D geologic media and structures and their effects on subsurface flow and transport. Its capabilities include flow of gas, water, and heat; flow of air, water, and heat; multiple chemically reactive and sorbing tracers; finite element/finite volume formulation; coupled stress module; saturated and unsaturated media; andmore » double porosity and double porosity/double permeability capabilities.« less
Heat transfer in serpentine passages with turbulence promoters
NASA Technical Reports Server (NTRS)
Boyle, R. J.
1984-01-01
Local heat transfer rates and overall pressure losses were determined for serpentine passages of square cross section. The flow entered an inlet leg, turned 180 deg and then passed through an outlet leg. Results were obtained for a passage with smooth walls for three different bend geometries and the effect of turbulence promoters was investigated. Turbulence promoters between 0.6 and 15% of the passage height were tested. Local heat transfer rates are determined from thermocouple measurements on a thin electrically heated Inconel foil and pressure drop is measured along the flow path.
Heat transfer to a silicon carbide/water nanofluid.
Yu, W.; France , D. M.; Smith, D. S.; Singh, D.; Timofeeva, E. V.; Routbort, J. L.; Univ. of Illinois at Chicago
2009-07-01
Heat transfer experiments were performed with a water-based nanofluid containing 170-nm silicon carbide particles at a 3.7% volume concentration and having potential commercial viability. Heat transfer coefficients for the nanofluid are presented for Reynolds numbers ranging from 3300 to 13,000 and are compared to the base fluid water on the bases of constant Reynolds number, constant velocity, and constant pumping power. Results were also compared to predictions from standard liquid correlations and a recently altered nanofluid correlation. The slip mechanisms of Brownian diffusion and thermophoresis postulated in the altered correlation were investigated in a series of heating and cooling experiments.
Heat Transfer Over the Circumference of a Heated Cylinder in Transverse Flow
NASA Technical Reports Server (NTRS)
Schmidt, Ernst; Wenner, Karl
1943-01-01
A method for recording the local heat-transfer coefficients on bodies in flow was developed. The cylinder surface was kept at constant temperature by the condensation of vapor except for a narrow strip which is heated separately to the same temperature by electricity. The heat-transfer coefficient at each point was determined from the electric heat output and the temperature increase. The distribution of the heat transfer along the circumference of cylinders was recorded over a range of Reynolds numbers of from 5000 to 426,000. The pressure distribution was measured at the same time. At Reynolds numbers up to around 100,000 high maximums of the heat transfer occurred in the forward stagnation point at and on the rear side at 180C, while at around 80 the heat-transfer coefficient on both sides of the cylinder behind the forward stagnation point manifested distinct minimums. Two other maximums occurred at around 115 C behind the forward stagnation point between 170,000 and 426,000. At 426,000 the heat transfer at the location of those maximums was almost twice as great as in the forward stagnation point, and the rear half of the cylinder diffused about 60 percent of the entire heat, The tests are compared with the results of other experimental and theoretical investigations.
Heat and mass transfer performances on plate fin and tube heat exchangers with dehumidification
Seshimo, Y.; Ogawa, K.; Marumoto, K.; Fujii, M. )
1990-09-01
The authors discuss how they conducted an experimental study on the air side performance of a single-row plate fin and tube heat exchanger in moist air where mass transfer exist under a relatively low driving potential. The results are as follows: The heat transfer with dehumidification is about 20% greater than that with only sensible heat transfer. Also the air side pressure drop is about 30-40% greater. The reason, as clarified by visual observations, comes from the condensate effect. To study how the condensate film affects performance, the presence of the stagnant condensate in the heat exchanger was modeled as an apparent change of the heat exchanger geometry, and the equivalent thickness of the condensate film was calculated from the increase in the air side pressure drop. As a result, if the presence of condensate in the heat exchanger is considered, then the heat transfer with dehumidification can be treated in the same way as with only sensible heat transfer. The analogy between heat and mass transfer does not strictly hold, the experimental results being closed to the Lewis Law.
A Conceptual Change Model for Teaching Heat Energy, Heat Transfer and Insulation
ERIC Educational Resources Information Center
Lee, C. K.
2014-01-01
This study examines the existing knowledge that pre-service elementary teachers (PSETs) have regarding heat energy, heat transfer and insulation. The PSETs' knowledge of heat energy was initially assessed by using an activity: determining which container would be best to keep hot water warm for the longest period of time. Results showed that…
Fernando Ascencio Cendejas; Jesus Rivera Rodriguez
1994-01-20
Disposal of hot separated brine by means of reinjection within the limits of the geothermal reservoir is, at present, a problem that remains to be solved. Possible thermal, as well as chemical contamination of the resources present key questions that have to be appropiately answered before a reinjection project is actually implemented in the field. This paper focusses on the basic heat-transfer process that takes place when a relatively cold brine is injected back into the naturally fractured hot geothermal reservoir after steam has been separated at the surface. The mathematical description of this process considers that rock matrix blocks behaves as uniformly distributed heat sources, meanwhile heat transfer between matrix blocks and the fluid contained in the fractures takes place under pseudo-steady state conditions with the main temperature drop occurring in the rock-matrix blocks interphase. Analytical solutions describing the thermal front speed of propagation are presented. Discussion on the effect of several variables affecting the thermal front speed of propagation is included, stressing the importance that a proper “in-situ” determination of the effective heat transfer area at the rock-fluid interphase has on the whole process. Solutions are also presented as a type-curve that can be practically used to estimate useful parameters involved in heat transfer phenomena during cold fluid reinjection in naturally fractured geothermal systems.
Radiant heat transfer from storage casks to the environment
Carlson, R W; Hovingh, J; Thomas, G R
1999-05-10
A spent fuel storage cask must efficiently transfer the heat released by the fuel assemblies through the cask walls to the environment. This heat must be transferred through passive means, limiting the energy transfer mechanisms from the cask to natural convection and radiation heat transfer.. Natural convection is essentially independent of the characteristics of the array of casks, provided there is space between casks to permit a convection loop. Radiation heat transfer, however, depends on the geometric arrangement of the array of casks because the peripheral casks will shadow the interior casks and restrict radiant heat transfer from all casks to the environment. The shadowing of one cask by its neighbors is determined by a view factor that represents the fraction of radiant energy that leaves the surface of a cask and reaches the environment. This paper addresses the evaluation of the view factor between a centrally located spent fuel storage cask and the environment. By combining analytic expressions for the view factor of (1) infinitely long cylinders and (2) finite cylinders with a length-to-diameter ratio of 2 to represent spent fuel storage casks, the view factor can be evaluated for any practical array of spent fuel storage casks.
Heat Transfer Enhancement in Separated and Vortex Flows
Richard J. Goldstein
2004-05-27
This document summarizes the research performance done at the Heat Transfer Laboratory of the University of Minnesota on heat transfer and energy separation in separated and vortex flow supported by DOE in the period September 1, 1998--August 31, 2003. Unsteady and complicated flow structures in separated or vortex flows are the main reason for a poor understanding of heat transfer under such conditions. The research from the University of Minnesota focused on the following important aspects of understanding such flows: (1) Heat/mass transfer from a circular cylinder; (2) study of energy separation and heat transfer in free jet flows and shear layers; and (3) study of energy separation on the surface and in the wake of a cylinder in crossflow. The current study used three different experimental setups to accomplish these goals. A wind tunnel and a liquid tunnel using water and mixtures of ethylene glycol and water, is used for the study of prandtl number effect with uniform heat flux from the circular cylinder. A high velocity air jet is used to study energy separation in free jets. A high speed wind tunnel, same as used for the first part, is utilized for energy separation effects on the surface and in the wake of the circular cylinder. The final outcome of this study is a substantial advancement in this research area.
Ultrasonic Heat Transfer Enhancement Using a Horn-Type Transducer
NASA Astrophysics Data System (ADS)
Nomura, Shinfuku; Yamamoto, Akira; Murakami, Koichi
2002-05-01
The purpose of this study is to clarify experimentally the influence of streaming induced by ultrasonic vibration on heat transfer using a horn-type ultrasonic vibrator. A horn tip of 6 mm diameter and 60.7 kHz resonant frequency was used as the ultrasonic transducer. Heat transfer experiments for a downward-facing horizontal heating surface with ultrasonic vibration from below were carried out in a natural convection region. The acoustic jet in the water from the horn tip of the transducer regarded as a nozzle exit was induced by this transducer, and as a result, up to a ten-fold increase in heat transfer coefficient was obtained by application of 20 W in both tap water and degassed water. It was found that the mechanism of heat transfer enhancement by ultrasonic vibration in tap water can be classified into four categories. In degassed water, heat transfer enhancement is influenced not by the acoustic jet, but by small-scale perturbations by cavitation microjets.
Stagnation region heat transfer augmentation at very high turbulence levels
Kingery, Joseph E.; Ames, Forrest E.
2016-08-01
Current land-based gas turbines are growing in size producing higher approach flow Reynolds numbers at the leading edge of turbine nozzles. These vanes are subjected to high intensity large scale turbulence. This present paper reports on the research which significantly expands the parameter range for stagnation region heat transfer augmenta-tion due to high intensity turbulence. Heat transfer measurements were acquired over two constant heat flux test surfaces with large diameter leading edges (10.16 cm and 40.64 cm). The test surfaces were placed downstream from a new high intensity (17.4%) mock combustor and tested over an eight to one range inmore » approach flow Reynolds number for each test surface. Stagnation region heat transfer augmentation for the smaller (ReD = 15,625–125,000) and larger (ReD = 62,500–500,000) leading edge regions ranged from 45% to 81% and 80% to 136%, respectively. Furthermore, these data also include heat transfer distributions over the full test surface compared with the earlier data acquired at six additional inlet turbulence conditions. These surfaces exhibit continued but more moderate acceleration downstream from the stagnation regions and these data are expected to be useful in testing bypass transition predictive approaches. This database will be useful to gas turbine heat transfer design engineers. [DOI: 10.1115/1.4032677]« less
Turbulent heat transfer prediction method for application to scramjet engines
NASA Technical Reports Server (NTRS)
Pinckney, S. Z.
1974-01-01
An integral method for predicting boundary layer development in turbulent flow regions on two-dimensional or axisymmetric bodies was developed. The method has the capability of approximating nonequilibrium velocity profiles as well as the local surface friction in the presence of a pressure gradient. An approach was developed for the problem of predicting the heat transfer in a turbulent boundary layer in the presence of a high pressure gradient. The solution was derived with particular emphasis on its applicability to supersonic combustion; thus, the effects of real gas flows were included. The resulting integrodifferential boundary layer method permits the estimation of cooling reguirements for scramjet engines. Theoretical heat transfer results are compared with experimental combustor and noncombustor heat transfer data. The heat transfer method was used in the development of engine design concepts which will produce an engine with reduced cooling requirements. The Langley scramjet engine module was designed by utilizing these design concepts and this engine design is discussed along with its corresponding cooling requirements. The heat transfer method was also used to develop a combustor cooling correlation for a combustor whose local properties are computed one dimensionally by assuming a linear area variation and a given heat release schedule.
He II heat transfer through superconducting cables electrical insulation
NASA Astrophysics Data System (ADS)
Baudouy, B.; François, M. X.; Juster, F.-P.; Meuris, C.
2000-02-01
For NbTi magnets cooled by superfluid helium (He II), the most severe heat barrier comes from the electrical insulation of the cables. Tests on electrical multi-layer insulations, made of Kapton ®, dry fiber and epoxy resin impregnated fiberglass tapes, indicate that heat transfer is influenced by He II contained in the insulation. Electrical insulation can be considered as a composite material made of a solid matrix with a complicated helium channels network. For several insulations, this network is characterized by steady-state heat transfer experiment through an elementary insulation pattern. Measurements in Landau regime for low temperature difference (10 -5-10 -3 K) and in Gorter-Mellink (GM) regime for higher temperature differences permit to determine an equivalent He II channel cross-section (10 -6 m 2) with an equivalent channel thickness (25 μm). We use the assumptions that He II heat transfer through the channels network and conduction in the insulation are decoupled and that the channels length is determined from the insulation overlap. It is observed that He II heat transfer is competing with conduction in the insulation. Furthermore, the measurements reveal an anomaly of heat transfer in the vicinity of the λ temperature which is associated to the phenomenon of λ-point depression.
Numerical computations of natural convection heat transfer in irregular geometries
NASA Astrophysics Data System (ADS)
Glakpe, E. K.
1987-01-01
This report explains the determination of buoyancy driven flow characteristics and heat transfer in enclosures of complex geometrical shapes. Applications of buoyancy driven flows can be found in solar collector devices, energy conservation technologies, cooling of micro-electronic chips, and nuclear reactor spent fuel shipping configurations. The problem is further complicated when three dimensional effects, non-Boussinesq effects, turbulence, and heat transfer by radiation are accounted for in the overall balance of energy transfer. This study developed a capability to model and predict the heat transfer and flow characteristics in shipping cask configurations involving light water and fast reactor fuel assemblies. We explored the complex flow phenomena involved in these configurations to develop numerical prediction capabilities to obtain data for the design and/or thermal analysis of such shipping casks.
O'Brien, James Edward; Sohal, Manohar Singh; Huff, George Albert
2002-08-01
A combined experimental and numerical investigation is under way to investigate heat transfer enhancement techniques that may be applicable to large-scale air-cooled condensers such as those used in geothermal power applications. The research is focused on whether air-side heat transfer can be improved through the use of finsurface vortex generators (winglets,) while maintaining low heat exchanger pressure drop. A transient heat transfer visualization and measurement technique has been employed in order to obtain detailed distributions of local heat transfer coefficients on model fin surfaces. Pressure drop measurements have also been acquired in a separate multiple-tube row apparatus. In addition, numerical modeling techniques have been developed to allow prediction of local and average heat transfer for these low-Reynolds-number flows with and without winglets. Representative experimental and numerical results presented in this paper reveal quantitative details of local fin-surface heat transfer in the vicinity of a circular tube with a single delta winglet pair downstream of the cylinder. The winglets were triangular (delta) with a 1:2 height/length aspect ratio and a height equal to 90% of the channel height. Overall mean fin-surface Nusselt-number results indicate a significant level of heat transfer enhancement (average enhancement ratio 35%) associated with the deployment of the winglets with oval tubes. Pressure drop measurements have also been obtained for a variety of tube and winglet configurations using a single-channel flow apparatus that includes four tube rows in a staggered array. Comparisons of heat transfer and pressure drop results for the elliptical tube versus a circular tube with and without winglets are provided. Heat transfer and pressure-drop results have been obtained for flow Reynolds numbers based on channel height and mean flow velocity ranging from 700 to 6500.
Heat transfer from cylinders in subsonic slip flows
NASA Technical Reports Server (NTRS)
Nagabushana, K. A.; Stainback, P. C.
1992-01-01
The heat transfer in heated wires was measured using a constant temperature anemometer over a Mach number range from 0.05 to 0.4 and pressures from 0.5 to 8.0 atmospheres. The total temperature ranged from 80 to 120 F and the wire diameters were 0.00015, 0.00032, and 0.00050 inch. The heat transfer data is presented in the form of a corrected Nusselt number. Based on suggested criteria, much of the data was obtained in the slip flow regime. Therefore, the data is compared with data having comparable flow conditions. The possible application of the heat transfer data to hot wire anemometry is discussed. To this end, the sensitivity of the wires to velocity, density, and total temperature is computed and compared using two different types of correlations.
Effect of boiling surface vibration on heat transfer
NASA Astrophysics Data System (ADS)
Alangar, Sathyabhama
2016-03-01
Experimental investigation of effect of forced vertical surface vibration on nucleate pool boiling heat transfer of saturated water at atmospheric pressure is presented in this paper. Vertical vibration was induced externally to the circular copper test surface on which boiling took place, using a vibration exciter. Frequency was varied in the range 0-25 Hz and amplitude of vibration was varied in the range 0-5 mm. Boiling takes place at much lower superheats for the same heat flux, slope of boiling curve decreases remarkably, when the surface is given external excitation. High frequency and high amplitude oscillations lead to more intensive heat transfer. There are some combinations of frequency and vibration amplitude, which cause up to two times increase in heat transfer coefficients.
Forced flow heat transfer of supercritical hydrogen for superconductor cooling
NASA Astrophysics Data System (ADS)
Shiotsu, M.; Shirai, Y.; Tatsumoto, H.; Hata, K.; Kobayashi, H.; Naruo, Y.; Inatani, H.
2014-01-01
Heat transfer from inner side of a vertical tube to forced flow of hydrogen was measured at the pressure of 1.5 MPa. The test tubes were made of stainless steel 316L with the inner diameters from 3 mm to 9 mm and lengths from 100 mm to 250 mm. Heat transfer curves were obtained by gradually increasing the heating current to the test tube and raising the surface temperature up to around 200 K. Inlet fluid temperature and flow velocity were varied from 21 to 30 K and 0.5 to 12 m/s, respectively. Effects of inlet temperature, flow velocity and tube dimension were clearly observed. The heat transfer curve for each flow velocity consists of a lower temperature region with a higher gradient and higher temperature region with a lower gradient. The experimental results were compared with the authors' correlation presented formerly. It was confirmed that this correlation can describe the experimental results obtained here.
Numerical simulation of transitional flows with heat transfer
NASA Astrophysics Data System (ADS)
Kožíšek, Martin; Příhoda, Jaromír; Fürst, Jiří; Straka, Petr
2016-06-01
The contribution deals with simulation of internal flows with the laminar/turbulent transition and heat transfer. The numerical modeling of incompressible flow on a heated flat plate was carried out partly by the k-kL-ω model of Walters and Cokljat [1] and partly by the algebraic transition model of Straka and Příhoda [2] connected with the EARSM turbulence model of Hellsten [3]. Transition models were tested by means of the skin friction and the Stanton number distribution. Used models of turbulent heat transfer were compared with the simplest model based on the constant turbulent Prandtl number. The k-kL-ω model is applied for the simulation of compressible flow through the VKI turbine blade cascade with heat transfer.
Advanced two-phase heat transfer systems
NASA Technical Reports Server (NTRS)
Swanson, Theodore D.
1992-01-01
Future large spacecraft, such as the Earth Observing System (EOS) platforms, will require a significantly more capable thermal control system than is possible with current 'passive' technology. Temperatures must be controlled much more tightly over a larger surface area. Numerous heat load sources will often be located inside the body of the spacecraft without a good view to space. Power levels and flux densities may be higher than can be accommodated with traditional technology. Integration and ground testing will almost certainly be much more difficult with such larger, more complex spacecraft. For these and similar reasons, the Goddard Space Flight Center (GSFC) has been developing a new, more capable thermal control technology called capillary pumped loops (CPL's). CPL's represent an evolutionary improvement over heat pipes; they can transport much greater quantities of heat over much longer distances and can serve numerous heat load sources. In addition, CPL's can be fabricated into large cold plates that can be held to tight thermal gradients. Development of this technology began in the early 1980's and is now reaching maturity. CPL's have recently been baselined for the EOS-AM platform (1997 launch) and the COMET spacecraft (1992 launch). This presentation describes this new technology and its applications. Most of the viewgraphs are self descriptive. For those that are less clear additional comments are provided.
Fluid dynamics at transition regions of enhanced heat transfer channels
NASA Astrophysics Data System (ADS)
Case, Jennifer C.; Pohlman, Nicholas A.
2012-11-01
Helical wire coil inserts are used to enhance heat transfer in high heat flux cooling channels. Past research using temperature probes has sufficiently proven that wire coils increase heat transfer by factors of three to five through the disruption of the boundary layer in the channels. The coils are passive devices that are inexpensive to manufacture and easily integrate into existing heat exchangers given the limited pressure drop they produce. Most of the fluid mechanics research in flow over helical coils has focused on the dynamics and vortex structure in fully developed regions rather than the short transition region where the enhanced heat transfer is often expected. Understanding how the development of the flow occurs over the axial length of the cooling channel will determine minimum dimensions necessary for enhanced heat transfer. Results of particle-shadow velocimetry (PSV) measurements report on the flow velocities and turbulence that occurs in the transition regions at the beginning of wire coil inserts. The ability to relate parameters such as flow rate, wire diameter, coil pitch, and the total tube length will increase fundamental knowledge and will allow for more efficient heat exchanger designs. Funding provided by NIU's Undergraduate Special Opportunities in Artistry & Research grant program.
Visualization of heat transfer for impinging swirl flow
Bakirci, K.; Bilen, K.
2007-10-15
The objective of the experimental study was to visualize the temperature distribution and evaluate heat transfer rate on the impingement surface kept at a constant wall temperature boundary condition for the swirling (SIJ), multi-channel (MCIJ) and conventional impinging jet (CIJ) using liquid crystal technique. The swirling jet assembly consisted of a housing tube and a solid swirl generator insert which had four narrow slots machined on its surface. The swirl angle, {theta}, was set as 0 , 22.5 , 41 , 50 to change the direction and strength of the swirl in the air flow exiting the housing tube. The local Nusselt numbers of the MCIJ ({theta} = 0 ) were generally much higher than those of CIJ and SIJs. As the swirl angle increased, the radial uniformity of the heat transfer was seen compared to MCIJ and SIJ; the best results were for {theta} = 50 and the jet-to-surface distance of H/D = 14. The location of the distance of the maximum heat transfer for the swirl angles of {theta} = 41 and 50 was shifted away from the stagnation point in a radial distance of nearly r/D = 2.5. Increasing Reynolds number for same swirler angle increased the heat transfer rate on the entire surface, and increased saddle shape heat transfer distribution on the surface, but had no significant effect on the position of the individual impingement regions, but increased saddle shape heat transfer distribution on the surface. The lower Reynolds number (Re = 10 000) and the highest H/D = 14 gave much more uniform local and average heat transfer distribution on the surface, but decreased their values on the entire surface. (author)
Combined heat and mass transfer in absorption processes
Grossman, G.
1982-01-01
The approach to theoretical analysis of the combined heat and mass transfer process taking place in absorption systems is described. The two tranfer phenomena are strongly coupled here. The purpose of the analysis is to relate, quantitatively, the heat and mass transfer coefficients to the physical properties of the working fluids and to the geometry of the system. The preferred configuration is that of a falling film of liquid on a metallic surface which serves to transfer heat from the absorbent in contact with the vapor of the absorbate. The model developed may be solved for laminar, turbulent, or transition flow regimes. The results of the solution describe the development of the thermal and concentration boundary layers and the variation of the temperatures, concentrations, and heat and mass fluxes. These quantities in their normalized, dimensionless form depend on two characteristic parameters of the system: the Lewis number Le and the dimensionless heat of absorption lambda. The length in the direction of flow is normalized with respect to the Peclet number and the film thickness. Heat and mass transfer coefficients for the system were calculated. The Sherwood number for mass transfer from the vapor-liquid interface to the bulk of the film reaches a constant value of 3.63 with fully developed boundary layers for both the adiabatic and constant temperature wall. The Nusselt number for heat transfer from the interface to the bulk reaches under the same conditions values of 3.63 and 2.67 for the adiabatic and constant temperature wall, respectively. The Nusselt number for heat tranfer from the bulk to the wall reaches 1.60.
Particle shape effect on heat transfer performance in an oscillating heat pipe
2011-01-01
The effect of alumina nanoparticles on the heat transfer performance of an oscillating heat pipe (OHP) was investigated experimentally. A binary mixture of ethylene glycol (EG) and deionized water (50/50 by volume) was used as the base fluid for the OHP. Four types of nanoparticles with shapes of platelet, blade, cylinder, and brick were studied, respectively. Experimental results show that the alumina nanoparticles added in the OHP significantly affect the heat transfer performance and it depends on the particle shape and volume fraction. When the OHP was charged with EG and cylinder-like alumina nanoparticles, the OHP can achieve the best heat transfer performance among four types of particles investigated herein. In addition, even though previous research found that these alumina nanofluids were not beneficial in laminar or turbulent flow mode, they can enhance the heat transfer performance of an OHP. PMID:21711830
NASA Astrophysics Data System (ADS)
Calisir, Tamer; Baskaya, Senol; Onur Yazar, Hakan; Yucedag, Sinan
2015-05-01
In this study the heat output of a panel-convector-convector-panel radiator (PCCP) under controlled laboratory conditions under Turkish household and especially Ankara conditions was investigated experimentally. In this sense, investigations were performed for different heating water mass flow rates, water inlet temperatures and radiator inlet and outlet connection positions, which are most commonly used in Turkey. An experimental setup was built for this purpose in a test room where temperature was controlled and held constant during the experiments. Inlet and outlet water temperatures and mass flow rates were measured and heat output of the radiator was calculated. Infrared thermal camera visualizations of the steel panel radiator front surface were also performed.
An investigation of heat pipe meniscus heat transfer
NASA Technical Reports Server (NTRS)
Saaski, E. W.; Franklin, J. L.; Mccreight, C. R.
1978-01-01
The use of grooved evaporator surfaces in heat pipes has increased in popularity in the past few years primarily due to the reproducibility achievable with grooved walls and the relatively low costs of the threading or extrusion processes involved in their production. The present study combines both analyses and experiments on square groove geometries, with special emphasis on overcoming the limitations of earlier analyses with finite-difference methods and groove-fillet hydrodynamic simplifications. The groove fillet, which has in previous analyses been assumed constant in radius of curvature, is permitted to change in thickness and curvature consistent with hydrodynamics and heat loss from the groove. A model is developed for accurate determination of the effect of constriction resistance on groove performance. The grooved-surface tests to be conducted are briefly described which will provide data under closely controlled operation to allow comparison and verification of the analyses.
Base fluid in improving heat transfer for EV car battery
NASA Astrophysics Data System (ADS)
Bin-Abdun, Nazih A.; Razlan, Zuradzman M.; Shahriman, A. B.; Wan, Khairunizam; Hazry, D.; Ahmed, S. Faiz; Adnan, Nazrul H.; Heng, R.; Kamarudin, H.; Zunaidi, I.
2015-05-01
This study examined the effects of base fluid (as coolants) channeling inside the heat exchanger in the process of the increase in thermal conductivity between EV car battery and the heat exchanger. The analysis showed that secondary cooling system by means of water has advantages in improving the heat transfer process and reducing the electric power loss on the form of thermal energy from batteries. This leads to the increase in the efficiency of the EV car battery, hence also positively reflecting the performance of the EV car. The present work, analysis is performed to assess the design and use of heat exchanger in increasing the performance efficiency of the EV car battery. This provides a preface to the use this design for nano-fluids which increase and improve from heat transfer.
Heat transfer measurements and CFD simulations of an impinging jet
NASA Astrophysics Data System (ADS)
Petera, Karel; Dostál, Martin
2016-03-01
Heat transport in impinging jets makes a part of many experimental and numerical studies because some similarities can be identified between a pure impingement jet and industrial processes like, for example, the heat transfer at the bottom of an agitated vessel. In this paper, experimental results based on measuring the response to heat flux oscillations applied to the heat transfer surface are compared with CFD simulations. The computational cost of a LES-based approach is usually too high therefore a comparison with less computationally expensive RANS-based turbulence models is made in this paper and a possible improvement of implementing an anisotropic explicit algebraic model for the turbulent heat flux model is evaluated.
NASA Technical Reports Server (NTRS)
Morris, J. F. (Inventor)
1985-01-01
This invention is directed to transferring heat from an extremely high temperature source to an electrically isolated lower temperature receiver. The invention is particularly concerned with supplying thermal power to a thermionic converter from a nuclear reactor with electric isolation. Heat from a high temperature heat pipe is transferred through a vacuum or a gap filled with electrically nonconducting gas to a cooler heat pipe. If the receiver requires gratr thermal power density, geometries are used with larger heat pipe areas for transmitting and receiving energy than the area for conducting the heat to the thermionic converter. In this way the heat pipe capability for increasing thermal power densities compensates for the comparative low thermal power densities through the electrically nonconducting gap between the two heat pipes.
Heat transfer by fluids in granulite metamorphism
NASA Technical Reports Server (NTRS)
Morgan, Paul; Ashwal, Lewis D.
1988-01-01
The thermal role of fluids in granulite metamorphism was presented. It was shown that for granulites to be formed in the middle crust, heat must be advected by either magma or by volatile fluids, such as water or CO2. Models of channelized fluid flow indicate that there is little thermal difference between channelized and pervasive fluid flow, for the same total fluid flux, unless the channel spacing is of the same order or greater than the thickness of the layer through which the fluids flow. The volumes of volatile fluids required are very large and are only likely to be found associated with dehydration of a subducting slab, if volatile fluids are the sole heat source for granulite metamorphism.
Stagnation Region Heat Transfer Augmentation at Very High Turbulence Levels
Ames, Forrest; Kingery, Joseph E.
2015-06-17
A database for stagnation region heat transfer has been extended to include heat transfer measurements acquired downstream from a new high intensity turbulence generator. This work was motivated by gas turbine industry heat transfer designers who deal with heat transfer environments with increasing Reynolds numbers and very high turbulence levels. The new mock aero-combustor turbulence generator produces turbulence levels which average 17.4%, which is 37% higher than the older turbulence generator. The increased level of turbulence is caused by the reduced contraction ratio from the liner to the exit. Heat transfer measurements were acquired on two large cylindrical leading edge test surfaces having a four to one range in leading edge diameter (40.64 cm and 10.16 cm). Gandvarapu and Ames [1] previously acquired heat transfer measurements for six turbulence conditions including three grid conditions, two lower turbulence aero-combustor conditions, and a low turbulence condition. The data are documented and tabulated for an eight to one range in Reynolds numbers for each test surface with Reynolds numbers ranging from 62,500 to 500,000 for the large leading edge and 15,625 to 125,000 for the smaller leading edge. The data show augmentation levels of up to 136% in the stagnation region for the large leading edge. This heat transfer rate is an increase over the previous aero-combustor turbulence generator which had augmentation levels up to 110%. Note, the rate of increase in heat transfer augmentation decreases for the large cylindrical leading edge inferring only a limited level of turbulence intensification in the stagnation region. The smaller cylindrical leading edge shows more consistency with earlier stagnation region heat transfer results correlated on the TRL (Turbulence, Reynolds number, Length scale) parameter. The downstream regions of both test surfaces continue to accelerate the flow but at a much lower rate than the leading edge. Bypass transition occurs
NASA Astrophysics Data System (ADS)
Shah, R. K.
1989-06-01
Various papers on numerical heat transfer using PCs and supercomputing are presented. Individual topics addressed include: a generalized program for computing two-dimensional boundary layers on a PC, microcomputer software for heat transfer education, PC-based adaptive irregular triangular grid generation for transient diffusion problems, numerical studies of convective heat transfer in an inclined semiannular enclosure, capabilities of PCs for numerical convective heat transfer, one-dimensional analysis of plane and radial thin film flows including solid-body rotation, and analysis of the transient compressible vapor flow in heat pipes. Also considered are: transient combined mixed convection and radiation from a straight vertical fin, finite element method for fluid flow and heat transfer on a PC, use of finite elements and PCs in teaching heat transfer, application of supercomputers to computational heat transfer, heat transfer to a thin liquid film with a free surface, numerical simulation of internal supersonic flow, and numerical prediction of vortex shedding behind a square cylinder.
Generator-absorber-heat exchange heat transfer apparatus and method and use thereof in a heat pump
Phillips, Benjamin A.; Zawacki, Thomas S.
1998-07-21
Numerous embodiments and related methods for generator-absorber heat exchange (GAX) are disclosed, particularly for absorption heat pump systems. Such embodiments and related methods use, as the heat transfer medium, the working fluid of the absorption system taken from the generator at a location where the working fluid has a rich liquor concentration.
Generator-absorber-heat exchange heat transfer apparatus and method and use thereof in a heat pump
Phillips, B.A.; Zawacki, T.S.
1998-07-21
Numerous embodiments and related methods for generator-absorber heat exchange (GAX) are disclosed, particularly for absorption heat pump systems. Such embodiments and related methods use, as the heat transfer medium, the working fluid of the absorption system taken from the generator at a location where the working fluid has a rich liquor concentration. 5 figs.
Heat transfer in rotating serpentine passages with smooth walls
NASA Technical Reports Server (NTRS)
Wagner, J. H.; Johnson, B. V.; Kopper, F. C.
1990-01-01
Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi-pass, smooth-wall heat transfer model with both radially inward and outward flow. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages (coolant-to-wall temperature ratio, Rossby number, Reynolds number and radius-to-passage hydraulic diameter ratio). These four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. It was found that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs and that the effect of rotation on the heat transfer coefficients was markedly different depending on the flow direction. Local heat transfer coefficients were found to decrease by as much as 60 percent and increase by 250 percent from no rotation levels. Comparisons with a pioneering stationary vertical tube buoyancy experiment showed reasonably good agreement. Correlation of the data is achieved employing dimensionless parameters derived from the governing flow equations.
Heat transfer from cylinders having closely spaced fins
NASA Technical Reports Server (NTRS)
Biermann, Arnold E
1937-01-01
The heat-transfer coefficients have been determined for five steel cylinders having fins 1.22 inches wide and the spacing between the fins ranging from 0.022 to 0.131 inch. The cylinders were tested with and without baffles in a wind tunnel; they were also tested enclosed in jackets with the cooling air supplied by a blower. A maximum heat transfer was reached at a fin space of about 0.45 inch for the cylinders tested with each of the three methods of cooling investigated. The rise in temperature of the air passing between the fins and the change in flow pattern were found to be important factors limiting the heat transfer that may be obtained by decreasing the fin space. The use of baffles for directing the air around the cylinders with closely spaced fins proved very effective in increasing the over-all heat-transfer coefficient, provided that the spacing was not appreciably less than that for maximum heat transfer.
Gravity and Heater Size Effects on Pool Boiling Heat Transfer
NASA Technical Reports Server (NTRS)
Kim, Jungho; Raj, Rishi
2014-01-01
The current work is based on observations of boiling heat transfer over a continuous range of gravity levels between 0g to 1.8g and varying heater sizes with a fluorinert as the test liquid (FC-72/n-perfluorohexane). Variable gravity pool boiling heat transfer measurements over a wide range of gravity levels were made during parabolic flight campaigns as well as onboard the International Space Station. For large heaters and-or higher gravity conditions, buoyancy dominated boiling and heat transfer results were heater size independent. The power law coefficient for gravity in the heat transfer equation was found to be a function of wall temperature under these conditions. Under low gravity conditions and-or for smaller heaters, surface tension forces dominated and heat transfer results were heater size dependent. A pool boiling regime map differentiating buoyancy and surface tension dominated regimes was developed along with a unified framework that allowed for scaling of pool boiling over a wide range of gravity levels and heater sizes. The scaling laws developed in this study are expected to allow performance quantification of phase change based technologies under variable gravity environments eventually leading to their implementation in space based applications.
Heat transfer in rotating serpentine passages with smooth walls
NASA Astrophysics Data System (ADS)
Wagner, J. H.; Johnson, B. V.; Kopper, F. C.
1990-06-01
Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multi-pass, smooth-wall heat transfer model with both radially inward and outward flow. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages (coolant-to-wall temperature ratio, Rossby number, Reynolds number and radius-to-passage hydraulic diameter ratio). These four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. It was found that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs and that the effect of rotation on the heat transfer coefficients was markedly different depending on the flow direction. Local heat transfer coefficients were found to decrease by as much as 60 percent and increase by 250 percent from no rotation levels. Comparisons with a pioneering stationary vertical tube buoyancy experiment showed reasonably good agreement. Correlation of the data is achieved employing dimensionless parameters derived from the governing flow equations.
Effects of Freestream Turbulence on Turbine Blade Heat Transfer
NASA Technical Reports Server (NTRS)
Boyle, Robert J.; Giel, Paul W.; Ames, Forrest E.
2004-01-01
Experiments have shown that moderate turbulence levels can nearly double turbine blade stagnation region heat transfer. Data have also shown that heat transfer is strongly affected by the scale of turbulence as well as its level. In addition to the stagnation region, turbulence is often seen to increase pressure surface heat transfer. This is especially evident at low to moderate Reynolds numbers. Vane and rotor stagnation region, and vane pressure surface heat transfer augmentation is often seen in a pre-transition environment. Accurate predictions of transition and relaminarization are critical to accurately predicting blade surface heat transfer. An approach is described which incorporates the effects of both turbulence level and scale into a CFD analysis. The model is derived from experimental data for cylindrical and elliptical leadng edges. Results using this model are compared to experimental data for both vane and rotor geometries. The comparisons are made to illustrate that using a model which includes the effects of turbulence length scale improves agreement with data, and to illustrate where improvements in the modeling are needed.
On heat transfer at microscale with implications for microactuator design
NASA Astrophysics Data System (ADS)
Ozsun, Ozgur; Alaca, B. Erdem; Yalcinkaya, Arda D.; Yilmaz, Mehmet; Zervas, Michalis; Leblebici, Yusuf
2009-04-01
The dominance of conduction and the negligible effect of gravity, and hence free convection, are verified in the case of microscale heat sources surrounded by air at atmospheric pressure. A list of temperature-dependent heat transfer coefficients is provided. In contrast to previous approaches based on free convection, supplied coefficients converge with increasing temperature. Instead of creating a new external function for the definition of boundary conditions via conductive heat transfer, convective thin film coefficients already embedded in commercial finite element software are utilized under a constant heat flux condition. This facilitates direct implementation of coefficients, i.e. the list supplied in this work can directly be plugged into commercial software. Finally, the following four-step methodology is proposed for modeling: (i) determination of the thermal time constant of a specific microactuator, (ii) determination of the boundary layer size corresponding to this time constant, (iii) extraction of the appropriate heat transfer coefficients from a list provided and (iv) application of these coefficients as boundary conditions in thermomechanical finite element simulations. An experimental procedure is established for the determination of the thermal time constant, the first step of the proposed methodology. Based on conduction, the proposed method provides a physically sound solution to heat transfer issues encountered in the modeling of thermal microactuators.
Heat transfer in rocket engine combustion chambers and nozzles
NASA Astrophysics Data System (ADS)
Anderson, P. G.; Cheng, G. C.; Farmer, R. C.
1993-07-01
Complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analyses verified with appropriate test data. Finally, the component analyses will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Since test data from the NLS development program are not available, new validation heat transfer data have been sought. Suitable data were obtained from a Rocketdyne test program on a model hydrocarbon/oxygen engine. Simulations of these test data will be presented. Recent interest in the hybrid motor have established the need for analyses of ablating solid fuels in the combustion chamber. Analysis of a simplified hybrid motor will also be presented.
Heat transfer in rocket engine combustion chambers and nozzles
NASA Astrophysics Data System (ADS)
Anderson, P. G.; Chen, Y. S.; Farmer, R. C.
1992-07-01
The complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analysis verified with appropriate test data. Finally, the component analysis will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Film cooling simulations of film coolant flows typical of the subscale Space Transportation Main Engine (STME) being experimentally studied by Pratt and Whitney have been made, and these results will be presented. Other film coolant experiments have also been simulated to verify the CFD heat transfer model being developed. The status of the study and its relevance as a new design tool are covered. Information is given in viewgraph form.
Heat transfer in rocket engine combustion chambers and nozzles
NASA Technical Reports Server (NTRS)
Anderson, P. G.; Chen, Y. S.; Farmer, R. C.
1992-01-01
The complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analysis verified with appropriate test data. Finally, the component analysis will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Film cooling simulations of film coolant flows typical of the subscale Space Transportation Main Engine (STME) being experimentally studied by Pratt and Whitney have been made, and these results will be presented. Other film coolant experiments have also been simulated to verify the CFD heat transfer model being developed. The status of the study and its relevance as a new design tool are covered. Information is given in viewgraph form.
Heat transfer in rocket engine combustion chambers and nozzles
NASA Technical Reports Server (NTRS)
Anderson, P. G.; Cheng, G. C.; Farmer, R. C.
1993-01-01
Complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analyses verified with appropriate test data. Finally, the component analyses will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Since test data from the NLS development program are not available, new validation heat transfer data have been sought. Suitable data were obtained from a Rocketdyne test program on a model hydrocarbon/oxygen engine. Simulations of these test data will be presented. Recent interest in the hybrid motor have established the need for analyses of ablating solid fuels in the combustion chamber. Analysis of a simplified hybrid motor will also be presented.
Analysis of heat transfer during quenching of a gear blank
Aceves, S M; Sahai, V
1999-03-01
This paper presents experimental and numerical results for the quench of a gear blank in agitated and stagnant oil. Heat transfer within the gear blank is analyzed with a whole domain-optimizer technique inverse solution method, to calculate the time history at every point in the gear blank. The development of this procedure represents the first stage in an overall analysis of the quench process that will later include material phase transformations and deformation. The paper presents ten variations in setting up the inverse problem, to analyze which combination of independent variables and decision variables results in the best match between experimental and numerical results. The results indicate that dividing the boundary of the gear blank into four zones and assigning a fixed heat transfer coefficient or heat flux to each zone yields an average RMS error (average difference between experimental and numerical results) of the order of 40 K. This error can be reduced by either increasing the number of zones, by reducing the number of thermocouples being matched, or by allowing the heat transfer or heat flux to vary within the zones. Of these possibilities, variation of heat transfer within the zones gives the best improvement in the quality of the match for the amount of extra effort required to run the problem.
Preflight reentry heat transfer analysis of Space Shuttle
NASA Technical Reports Server (NTRS)
Ko, W. L.; Quinn, R. D.; Gong, L.; Schuster, L. S.; Gonzales, D.
1981-01-01
Preflight predictions of the structural temperature distributions during entry are compared with data from the initial Shuttle flight. Finite element thermal analysis programming was used to model the heat flow on Shuttle structures and actual gas properties of air were employed in the analyses of aerodynamic heating. Laminar, separated, and turbulent heat fluxes were calculated for varying locations on the craft using velocity-attitude and angle-of-attack projections taken from the nominal STS-1 trajectory. Temperature time histories of the first flight are compared with laminar and turbulent flow assumptions and an unpredicted rapid cooling 1800 sec into entry is credited to inaccurate assumptions of structural heat dissipative properties or flow conditions in that time phase of the flight; additional discrepancies in descriptions of heating of the upper fuselage are attributed to a lack of knowledge of the complex flow patterns existing over that area of the Shuttle body.
Implant Fixture Heat Transfer During Abutment Preparation.
Aleisa, Khalil; Alkeraidis, Abdullah; Al-Dwairi, Ziad Nawaf; Altahawi, Hamdi; Lynch, Edward
2015-06-01
The purpose of the study was to evaluate the effect of water flow rate on the heat transmission in implants during abutment preparation using a diamond bur in a high-speed dental turbine. Titanium-alloy abutments (n = 32) were connected to a titanium-alloy implant embedded in an acrylic resin within a water bath at a controlled temperature of 37°C. The specimens were equally distributed into 2 groups (16 each) according to the water flow rate used during the preparation phase. Group 1 had a water flow rate of 24 mL/min, and group 2 had a water flow rate of 40 mL/min. Each abutment was prepared in the axial plane for 1 minute and in the occlusal plane for 1 minute with a coarse tapered diamond bur using a high-speed dental handpiece. Thermocouples embedded at the cervix of the implant surface were used to record the temperature of heat transmission from the abutment preparation. Heat generation was measured at 3 distinct times (immediately and 30 seconds and 60 seconds after the end of preparation). Statistical analyses were carried out using 2-way analysis of variance and the Student t test. Water flow rates (24 mL vs 40 mL) and time interval had no statistically significant effect on the implant's temperature change during the abutment preparation stage (P = .431 and P = .064, respectively). Increasing the water flow rate from 24 to 40 mL/min had no influence on the temperature of the implant fixture recorded during preparation of the abutment. PMID:23713452
Heat transfer and core neutronics considerations of the heat pipe cooled thermionic reactor
NASA Astrophysics Data System (ADS)
Determan, W. R.; Lewis, Brian
The authors summarize the results of detailed neutronic and thermal-hydraulic evaluations of the heat pipe cooled thermionic (HPTI) reactor design, identify its key design attributes, and quantify its performance characteristics. The HPTI core uses modular, liquid-metal core heat transfer assemblies to replace the liquid-metal heat transport loop employed by in-core thermionic reactor designs of the past. The nuclear fuel, power conversion, heat transport, and heat rejection functions are all combined into a single modular unit. The reactor/converter assembly uses UN fuel pins to obtain a critical core configuration with in-core safety rods and reflector controls added to complete the subassembly. By thermally bonding the core heat transfer assemblies during the reactor core is coupled neutronically, thermally, and electrically into a modular assembly of individual power sources with cross-tied architecture. A forward-facing heat pipe radiator assembly extends from the reactor head in the shape of a frustum of a cone on the opposite side of the power system from the payload. Important virtues of the concept are the absence of any single-point failures and the ability of the core to effectively transfer the TFE waste heat load laterally to other in-core heat transfer assemblies in the event of multiple failures in either in-core and radiator heat pipes.
Heat transfer and core neutronics considerations of the heat pipe cooled thermionic reactor
NASA Technical Reports Server (NTRS)
Determan, W. R.; Lewis, Brian
1991-01-01
The authors summarize the results of detailed neutronic and thermal-hydraulic evaluations of the heat pipe cooled thermionic (HPTI) reactor design, identify its key design attributes, and quantify its performance characteristics. The HPTI core uses modular, liquid-metal core heat transfer assemblies to replace the liquid-metal heat transport loop employed by in-core thermionic reactor designs of the past. The nuclear fuel, power conversion, heat transport, and heat rejection functions are all combined into a single modular unit. The reactor/converter assembly uses UN fuel pins to obtain a critical core configuration with in-core safety rods and reflector controls added to complete the subassembly. By thermally bonding the core heat transfer assemblies during the reactor core is coupled neutronically, thermally, and electrically into a modular assembly of individual power sources with cross-tied architecture. A forward-facing heat pipe radiator assembly extends from the reactor head in the shape of a frustum of a cone on the opposite side of the power system from the payload. Important virtues of the concept are the absence of any single-point failures and the ability of the core to effectively transfer the TFE waste heat load laterally to other in-core heat transfer assemblies in the event of multiple failures in either in-core and radiator heat pipes.
Radiative heat transfer in coal furnaces
Ahluwalia, R.K.; Im, K.H.
1992-01-01
A hybrid technique has been developed to solve three-dimensional spectral radiation transport equations for absorbing, emitting and anisotropically scattering media. An optimal mix of computational speed and accuracy is obtained by combining the discrete ordinate method (S{sub 4}), modified differential approximation (MDA) and P{sub 1} approximation for use in different range of optical thicknesses. The technique is used in conjunction with a char burnout model and spectroscopic data for H{sub 2}O, CO{sub 2}, CO, char, soot and ash to determine the influence of ash composition, ash content and coal preparation on furnace heat absorption.
Radiative heat transfer in coal furnaces
Ahluwalia, R.K.; Im, K.H.
1992-09-01
A hybrid technique has been developed to solve three-dimensional spectral radiation transport equations for absorbing, emitting and anisotropically scattering media. An optimal mix of computational speed and accuracy is obtained by combining the discrete ordinate method (S{sub 4}), modified differential approximation (MDA) and P{sub 1} approximation for use in different range of optical thicknesses. The technique is used in conjunction with a char burnout model and spectroscopic data for H{sub 2}O, CO{sub 2}, CO, char, soot and ash to determine the influence of ash composition, ash content and coal preparation on furnace heat absorption.
Heat transfer and friction correlations for wavy plate fin-and-tube heat exchangers
Kim, N.H.; Youn, J.H.; Webb, R.L.
1996-12-31
This paper deals with heat exchangers having plate fins of herringbone wave configuration. Correlations are developed to predict the air-side heat transfer coefficient and friction factor as a function of flow conditions and geometric variables of the heat exchanger. Correlations are provided for both staggered and in-line arrays of circular tubes. A multiple regression technique was used to correlate 41 wavy fin geometries by Beecher and Fagan (1987), Wang et al. (1995) and Beecher (1968). For the staggered layout, 92% of the heat transfer data are correlated within {+-}10%, and 91% of the friction data are correlated within {+-}15%.
Boiling Heat Transfer in High Temperature Generator of Absorption Chiller/Heater
NASA Astrophysics Data System (ADS)
Furukawa, Masahiro; Enomoto, Eiichi; Sekoguchi, Kotohiko
Heat transfer performance of forced convective boiling in high temperature generator was experimentally studied using an actual absorption chiller/heater. Measurements were made at six locations, three different levels on a couple of laterally separated lines, for the fluid rising along the rear wall of the high temperature generator furnace. Fluids tested were water and lithium bromide aqueous solution. System pressures were maintained at 96 and 24 kPa, and firing rates were changed from 100 to 40 % of the full load of the machine. Through the experiments, thermodynamic states of both of the fluids were in subcooled region at the lower and middle locations and in saturated region at the upper location. It can be suggested that saturated boiling occurs at comparatively narrow area, located at the upper zone of heat transfer surface of the generator, while forced convective heat transfer and subcooled boiling appear at the remaining broad area. Enhancement of heat transfer due to saturated boiling was not pronounced for lithium bromide aqueous solution than for water.
The effects of leading edge and downstream film cooling on turbine vane heat transfer
NASA Technical Reports Server (NTRS)
Hylton, L. D.; Nirmalan, V.; Sultanian, B. K.; Kaufman, R. M.
1988-01-01
The progress under contract NAS3-24619 toward the goal of establishing a relevant data base for use in improving the predictive design capabilities for external heat transfer to turbine vanes, including the effect of downstream film cooling with and without leading edge showerhead film cooling. Experimental measurements were made in a two-dimensional cascade previously used to obtain vane surface heat transfer distributions on nonfilm cooled airfoils under contract NAS3-22761 and leading edge showerhead film cooled airfoils under contract NAS3-23695. The principal independent parameters (Mach number, Reynolds number, turbulence, wall-to-gas temperature ratio, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio) were maintained over ranges consistent with actual engine conditions and the test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. Data provide a data base for downstream film cooled turbine vanes and extends the data bases generated in the two previous studies. The vane external heat transfer obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The data obtained and presented illustrate the interaction of the variables and should provide the airfoil designer and computational analyst the information required to improve heat transfer design capabilities for film cooled turbine airfoils.
Numerical prediction of radiation heat transfer in optoelectronics hermetic packaging process
NASA Astrophysics Data System (ADS)
Saha, Chinmoy P.; Zhang, Daming; Liu, Sheng
2005-03-01
Hermetic packaging of the high-speed optoelectronics devices is important not only for robustness but also to protect the device from adverse operational environments and ensure reliable communications. We have developed a complete hermetic packaging assembly process for a photonic Mini-DIL module of 10.0Gbps type. We have developed and simulated the step by step fluxless reflow soldering process (pick and place) of the whole mini-module package and finally, the hermetic sealing by Finite Element Analysis (FEA) simulation. A commercially available, general purpose, finite element program - ABAQUS has been used along with Altair HyperWorks as pre and post processor for this numerical simulation. The actual 3-D model has been simplified to the 2-D model for the hermetic sealing, radiation heat transfer prediction to reduce computational complicacy. During the sealing process at a high temperature, there is a possibility of considerable heat transfer from the module top sealing cap to the high temperature susceptible LD (Laser Diode). In the event of a critical temperature the LD may suffer malfunction and eventual destruction. Radiation along with the conduction heat transfer mechanism has been modeled for this sealing to predict the temperature variation as a result of heat transfer from wledspots to the LD. Various issues with cavity radiations such as, effect of radiation view factor, surface blocking and surface emissivity have been considered and results discussed. The convection mechanism has been neglected considering the hermeticity of the sealing.
The effects of leading edge and downstream film cooling on turbine vane heat transfer
NASA Astrophysics Data System (ADS)
Hylton, L. D.; Nirmalan, V.; Sultanian, B. K.; Kaufman, R. M.
1988-11-01
The progress under contract NAS3-24619 toward the goal of establishing a relevant data base for use in improving the predictive design capabilities for external heat transfer to turbine vanes, including the effect of downstream film cooling with and without leading edge showerhead film cooling. Experimental measurements were made in a two-dimensional cascade previously used to obtain vane surface heat transfer distributions on nonfilm cooled airfoils under contract NAS3-22761 and leading edge showerhead film cooled airfoils under contract NAS3-23695. The principal independent parameters (Mach number, Reynolds number, turbulence, wall-to-gas temperature ratio, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio) were maintained over ranges consistent with actual engine conditions and the test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. Data provide a data base for downstream film cooled turbine vanes and extends the data bases generated in the two previous studies. The vane external heat transfer obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The data obtained and presented illustrate the interaction of the variables and should provide the airfoil designer and computational analyst the information required to improve heat transfer design capabilities for film cooled turbine airfoils.
Heat Transfer Measurements on Surfaces with Natural Ice Castings and Modeled Roughness
NASA Technical Reports Server (NTRS)
Breuer, Kenneth S.; Torres, Benjamin E.; Orr, D. J.; Hansman, R. John
1997-01-01
An experimental method is described to measure and compare the convective heat transfer coefficient of natural and simulated ice accretion roughness and to provide a rational means for determining accretion-related enhanced heat transfer coefficients. The natural ice accretion roughness was a sample casting made from accretions at the NASA Lewis Icing Research Tunnel (IRT). One of these castings was modeled using a Spectral Estimation Technique (SET) to produce three roughness elements patterns that simulate the actual accretion. All four samples were tested in a flat-plate boundary layer at angle of attack in a "dry" wind tunnel test. The convective heat transfer coefficient was measured using infrared thermography. It is shown that, dispite some problems in the current data set, the method does show considerable promise in determining roughness-induced heat transfer coefficients, and that, in addition to the roughness height and spacing in the flow direction, the concentration and spacing of elements in the spanwise direction are important parameters.
Heat Transfer Enhancement for Finned-tube Heat Exchangers with Winglets
O'Brien, James Edward; Sohal, Manohar Singh
2000-11-01
This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with a circular tube and/or a delta-winglet pair. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficient distributions were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over an airflow rate ranging from 1.51 x 10-3 to 14.0 x 10-3 kg/s. These flow rates correspond to a duct-height Reynolds number range of 670 – 6300 with a duct height of 1.106 cm and a duct width-toheight ratio, W/H, of 11.25. The test cylinder was sized such that the diameter-to-duct height ratio, D/H is 5. Results presented in this paper reveal visual and quantitative details of local fin-surface heat transfer distributions in the vicinity of a circular tube, a delta-winglet pair, and a combination of a circular tube and a delta-winglet pair. Comparisons of local and average heat transfer distributions for the circular tube with and without winglets are provided. Overall mean finsurface Nusselt-number results indicate a significant level of heat transfer enhancement associated with the deployment of the winglets with the circular cylinder. At the lowest Reynolds numbers (which correspond to the laminar operating conditions of existing geothermal air-cooled condensers), the enhancement level is nearly a factor of two. At higher Reynolds numbers, the enhancement level is close to 50%.
Heat transfer and flow visualization of swirling impinging jets
Huang, L.; El-Genk, M.S.
1996-12-31
The heat transfer performance of swirling impinging jets was experimentally investigated, and the flow fields were visualized for a jet diameter, d{sub j} = 12.7 mm and swirl angles, {theta} = 15{degree}, 30{degree}, and 45{degree}. Other experimental parameters included Reynolds number, Re = 3,620--17,600, vertical jet spacing, h = 12.7--76.2 mm, and radial distance from the stagnation point, r = 0--65 mm. The results showed significant enhancement in the heat transfer coefficient, both with respect to radial uniformity and local values, compared to a circular straight impinging jet of the same dimensions at the same test conditions. The flow field visualizations confirmed the measured enhancement in the heat transfer coefficient for the swirling jets as well as the radial distribution of local Nusselt number.
Reflective Coating on Fibrous Insulation for Reduced Heat Transfer
NASA Technical Reports Server (NTRS)
Hass, Derek D.; Prasad, B. Durga; Glass, David E.; Wiedemann, Karl E.
1997-01-01
Radiative heat transfer through fibrous insulation used in thermal protection systems (TPS) is significant at high temperatures (1200 C). Decreasing the radiative heat transfer through the fibrous insulation can thus have a major impact on the insulating ability of the TPS. Reflective coatings applied directly to the individual fibers in fibrous insulation should decrease the radiative heat transfer leading to an insulation with decreased effective thermal conductivity. Coatings with high infrared reflectance have been developed using sol-gel techniques. Using this technique, uniform coatings can be applied to fibrous insulation without an appreciable increase in insulation weight or density. Scanning electron microscopy, Fourier Transform infrared spectroscopy, and ellipsometry have been performed to evaluate coating performance.
Convective heat transfer around vertical jet fires: an experimental study.
Kozanoglu, Bulent; Zárate, Luis; Gómez-Mares, Mercedes; Casal, Joaquim
2011-12-15
The convection heat transfer phenomenon in vertical jet fires was experimentally analyzed. In these experiments, turbulent propane flames were generated in subsonic as well as sonic regimes. The experimental data demonstrated that the rate of convection heat transfer increases by increasing the length of the flame. Assuming the solid flame model, the convection heat transfer coefficient was calculated. Two equations in terms of adimensional numbers were developed. It was found out that the Nusselt number attains greater values for higher values of the Rayleigh and Reynolds numbers. On the other hand, the Froude number was analyzed only for the subsonic flames where the Nusselt number grows by this number and the diameter of the orifice. PMID:21962859
Sensitivity Equation Derivation for Transient Heat Transfer Problems
NASA Technical Reports Server (NTRS)
Hou, Gene; Chien, Ta-Cheng; Sheen, Jeenson
2004-01-01
The focus of the paper is on the derivation of sensitivity equations for transient heat transfer problems modeled by different discretization processes. Two examples will be used in this study to facilitate the discussion. The first example is a coupled, transient heat transfer problem that simulates the press molding process in fabrication of composite laminates. These state equations are discretized into standard h-version finite elements and solved by a multiple step, predictor-corrector scheme. The sensitivity analysis results based upon the direct and adjoint variable approaches will be presented. The second example is a nonlinear transient heat transfer problem solved by a p-version time-discontinuous Galerkin's Method. The resulting matrix equation of the state equation is simply in the form of Ax = b, representing a single step, time marching scheme. A direct differentiation approach will be used to compute the thermal sensitivities of a sample 2D problem.
Nuclear reactor fuel element having improved heat transfer
Garnier, J.E.; Begej, S.; Williford, R.E.; Christensen, J.A.
1982-03-03
A nuclear reactor fuel element having improved heat transfer between fuel material and cladding is described. The element consists of an outer cladding tube divided into an upper fuel section containing a central core of fissionable or mixed fissionable and fertile fuel material, slightly smaller in diameter than the inner surface of the cladding tube and a small lower accumulator section, the cladding tube being which is filled with a low molecular weight gas to transfer heat from fuel material to cladding during irradiation. A plurality of essentially vertical grooves in the fuel section extend downward and communicate with the accumulator section. The radial depth of the grooves is sufficient to provide a thermal gradient between the hot fuel surface and the relatively cooler cladding surface to allow thermal segregation to take place between the low molecular weight heat transfer gas and high molecular weight fission product gases produced by the fuel material during irradiation.
Effects of wake passing on stagnation region heat transfer
NASA Astrophysics Data System (ADS)
O'Brien, J. E.
In the present experimental study, an annular-flow wind tunnel fitted with a spoked-wheel wake generator was used to ascertain both time-averaged and time-resolved effects of wake passing in a cylinder stagnation region; the cylindrical spokes generated wakes simulating those of a turbine inlet guide vanes. The time-averaged heat transfer results obtained indicate an asymmetric heat-transfer coefficient distribution about the stagnation line, with higher heat-transfer coefficients on the side corresponding to the suction side of the turbine blade. Spectra of the hot-film records indicate that vortex-shedding is a major contributor to the unsteady buffeting of the test-cylinder boundary layer at circumferential stations located at both + and -60 deg from the stagnation line, despite making only a minor contribution to the stagnation line itself.
Review of experimental investigations of liquid-metal heat transfer
NASA Technical Reports Server (NTRS)
Lubarsky, Bernard; Kaufman, Samuel J
1956-01-01
Experimental data of various investigators of liquid-metal heat-transfer characteristics were reevaluated using as consistent assumptions and methods as possible and then compared with each other and with theoretical results. The reevaluated data for both local fully developed and average Nusselt numbers in the turbulent flow region were found still to have considerable spread, with the bulk of the data being lower than predicted by existing analysis. An equation based on empirical grounds which represents most of the fully developed heat-transfer data is nu = 0.625 pe(0.4) where nu represents the Nusselt number and pe the Peclet number. The theoretical prediction of the heat transfer in the entrance region was found to give lower values, in most cases, than those found in the experimental work.
Convective heat transfer to low-temperature fluids
NASA Technical Reports Server (NTRS)
Graham, R. W.; Hendricks, R. C.; Simoneau, R. J.
1974-01-01
Research into forced and natural convection processes in low-temperature (cryogenic) fluids is reviewed with primary emphasis on forced convection. Boundaries of the near-critical region are defined, fluid properties near the critical state are discussed, and heat-transfer processes around the critical point are described. The thermodynamics of the critical point is analyzed together with transport properties of a near-critical fluid, and the quantum states of low-temperature molecular hydrogen (para and ortho) are discussed. Experimental work on heat transfer in free, natural, and forced convection systems is briefly summarized. Graham's (1969) penetration model for near-critical fluids is outlined, near-critical heat transfer is discussed in relation to conventional geometric effects, and the effects of curvature on the properties of near-critical hydrogen are noted. Theoretical considerations in free and forced convection are examined.
Measurement of airfoil heat transfer coefficients on a turbine stage
NASA Astrophysics Data System (ADS)
Dring, Robert P.; Blair, Michael F.; Joslyn, H. David
1987-10-01
A combined experimental and analytical program was conducted to examine the impact of a number of variables on the midspan heat transfer coefficients of the three airfoil rows in a one and one-half stage large scale turbine model. Variables included stator/rotor axial spacing, Reynolds number, turbine inlet turbulence, flow coefficient, relevant stator 1/stator 2 circumferential position, and rotation. Heat transfer data were acquired on the suction and pressure surfaces of the three airfoils. High density data were also acquired in the leading edge stagnation regions. Extensive documentation of the steady and unsteady aerodynamics was acquired. Finally, heat transfer data were compared with both a steady and an unsteady boundary layer analysis.
Convective heat transfer with film cooling around a rotor blade
NASA Astrophysics Data System (ADS)
Arts, T.
This paper deals with an experimental convective heat transfer investigation around a high pressure gas turbine film cooled rotor blade. The measurements were performed in the von Karman Institute short duration isentropic light piston compression tube facility allowing a correct simulation of Mach and Reynolds number as well as free stream to wall and free stream to coolant temperature ratios. The airfoil was mounted in a linear stationary cascade environment and heat transfer measurements were obtained by using platinum thin film gages painted on a blade made of machinable glass ceramic. The coolant flow was ejected simultaneously through the leading edge (3 rows of holes), the suction side (2 rows of holes), and the pressure side (1 row of holes). The coolant hydrodynamic behavior is described and the effects of overall coolant to free stream mass weight ratio, coolant to free stream temperature ratio, and free stream turbulence intensity on the convective heat transfer distribution are successively described.
Stagnation Point Heat Transfer with Gas Injection Cooling
NASA Technical Reports Server (NTRS)
Vancrayenest, B.; Tran, M. D.; Fletcher, D. G.
2005-01-01
The present paper deals with an experimental study of the stagnation-point heat transfer to a cooled copper surface with gas injection under subsonic conditions. Test were made with a probe that combined a steady-state water-cooled calorimeter that allows the capability to study convective blockage and to perform heat transfer measurements in presence of gas injection in the stagnation region. The copper probe was pierced by 52 holes, representing 2.4% of the total probe surface. The 1.2 MW high enthalpy plasma wind tunnel was operated at anode powers between 130 and 230 kW and a static pressures from 35 hPa up to 200 hPa. Air, carbon dioxide and argon were injected in the mass flow range 0-0.4 g/s in the boundary layer developed around the 50 mm diameter probe. The measured stagnation-point heat transfer rates are reported and discussed.
Gas flow environment and heat transfer nonrotating 3D program
NASA Technical Reports Server (NTRS)
Schulz, R. J.
1982-01-01
A complete set of benchmark quality data for the flow and heat transfer within a large rectangular turning duct is provided. These data are to be used to evaluate, and verify, three-dimensional internal viscous flow models and computational codes. The analytical contract objective is to select a computational code and define the capabilities of this code to predict the experimental results obtained. Details of the proper code operation will be defined and improvements to the code modeling capabilities will be formulated. Internal flow in a large rectangular cross-sectioned 90 deg. bend turning duct was studied. The duct construction was designed to allow detailed measurements to be made for the following three duct wall conditions: (1) an isothermal wall with isothermal flow; (2) an adiabatic wall with convective heat transfer by mixing between an unheated surrounding flow; and (3) an isothermal wall with heat transfer from a uniformly hot inlet flow.
Forced convection heat transfer to air/water vapor mixtures
NASA Technical Reports Server (NTRS)
Richards, D. R.; Florschuetz, L. W.
1986-01-01
Heat transfer coefficients were measured using both dry air and air/water vapor mixtures in the same forced convection cooling test rig (jet array impingement configurations) with mass ratios of water vapor to air up to 0.23. The primary objective was to verify by direct experiment that selected existing methods for evaluation of viscosity and thermal conductivity of air/water vapor mixtures could be used with confidence to predict heat transfer coefficients for such mixtures using as a basis heat transfer data for dry air only. The property evaluation methods deemed most appropriate require as a basis a measured property value at one mixture composition in addition to the property values for the pure components.
46 CFR 153.436 - Heat transfer fluids: compatibility with cargo.
Code of Federal Regulations, 2012 CFR
2012-10-01
... 46 Shipping 5 2012-10-01 2012-10-01 false Heat transfer fluids: compatibility with cargo. 153.436... Equipment Cargo Temperature Control Systems § 153.436 Heat transfer fluids: compatibility with cargo. A heat transfer fluid separated from the cargo by only one wall (for example, the heat transfer fluid in a...
46 CFR 153.436 - Heat transfer fluids: compatibility with cargo.
Code of Federal Regulations, 2011 CFR
2011-10-01
... 46 Shipping 5 2011-10-01 2011-10-01 false Heat transfer fluids: compatibility with cargo. 153.436... Equipment Cargo Temperature Control Systems § 153.436 Heat transfer fluids: compatibility with cargo. A heat transfer fluid separated from the cargo by only one wall (for example, the heat transfer fluid in a...
46 CFR 153.436 - Heat transfer fluids: compatibility with cargo.
Code of Federal Regulations, 2014 CFR
2014-10-01
... 46 Shipping 5 2014-10-01 2014-10-01 false Heat transfer fluids: compatibility with cargo. 153.436... Equipment Cargo Temperature Control Systems § 153.436 Heat transfer fluids: compatibility with cargo. A heat transfer fluid separated from the cargo by only one wall (for example, the heat transfer fluid in a...
46 CFR 153.436 - Heat transfer fluids: compatibility with cargo.
Code of Federal Regulations, 2010 CFR
2010-10-01
... 46 Shipping 5 2010-10-01 2010-10-01 false Heat transfer fluids: compatibility with cargo. 153.436... Equipment Cargo Temperature Control Systems § 153.436 Heat transfer fluids: compatibility with cargo. A heat transfer fluid separated from the cargo by only one wall (for example, the heat transfer fluid in a...
46 CFR 153.436 - Heat transfer fluids: compatibility with cargo.
Code of Federal Regulations, 2013 CFR
2013-10-01
... 46 Shipping 5 2013-10-01 2013-10-01 false Heat transfer fluids: compatibility with cargo. 153.436... Equipment Cargo Temperature Control Systems § 153.436 Heat transfer fluids: compatibility with cargo. A heat transfer fluid separated from the cargo by only one wall (for example, the heat transfer fluid in a...
Thermocapillary effects on the heat transfer effectiveness of a heated, curved meniscus
Pratt, D.M.; Hallinan, K.P.; Chang, W.S.
1997-07-01
An investigation of thermocapillary effects on a heated meniscus formed by a volatile liquid in a vertical capillary tube has been conducted. This investigation is primarily experimental although analysis is presented to gain insights into the experimental results. The work was motivated by the importance of the evaporation process from porous or grooved media that are integral to the operation of capillary-driven heat transport devices such as heat pipes and capillary-driven loops. The research addressed the heat transfer characteristics of a capillary pore system. It was shown that the heat transfer effectiveness of the evaporating meniscus was reduced due to interfacial thermocapillary stresses. The effect of thermocapillary stresses on the heat transfer characteristics on single capillary pore heat transfer devices is shown to be a function of the non-dimensional thermocapillary stress (Marangoni number). This was demonstrated for different capillary pore sizes and working fluid conditions. Results include data for inside diameters of 0.5, 1, and 2 mm and liquid subcoolings of 18, 10, and 0 C. For large pores, it was shown that the heat transfer is controlled by convection.
Cho, Y.I.; Lorsch, H.G.
1991-03-31
The feasibility of adding phase change materials (PCMS) and surfactants to the heat transfer fluids in district cooling systems was investigated. It increases the thermal capacity of the heat transfer fluid and therefore decreases the volume that needs to be pumped. It also increases the heat transfer rate, resulting in smaller heat exchangers. The thermal behavior of two potential PCMS, hexadecane and tetradecane paraffin wax, was experimentally evaluated. The heat of fusion of these materials is approximately 60% of that of ice. They exhibit no supercooling and are stable under repeated thermal cycling. While test results for laboratory grade materials showed good agreement with data in the literature, both melting point and heat of fusion for commercial grade hexadecane were found to be considerably lower than literature values. PCM/water mixtures were tested in a laboratory-scale test loop to determine heat transfer and flow resistance properties. For 10% and 25% PCM/water slurries, the heat transfer enhancement was found to be approximately 18 and 30 percent above the value for water, respectively. Within the turbulent region, there is only a minor pumping penalty from the addition of up to 25% PCM to the water. Research is continuing on these fluids in order to determine their behavior in large-size loops and to arrive at optimum formulations.
A laser-induced heat flux technique for convective heat transfer measurements in high speed flows
NASA Technical Reports Server (NTRS)
Porro, A. R.; Keith, T. G., Jr.; Hingst, W. R.
1991-01-01
A technique is developed to measure the local convective heat transfer coefficient on a model surface in a supersonic flow field. The technique uses a laser to apply a discrete local heat flux at the model test surface, and an infrared camera system determines the local temperature distribution due to the heating. From this temperature distribution and an analysis of the heating process, a local convective heat transfer coefficient is determined. The technique was used to measure the local surface convective heat transfer coefficient distribution on a flat plate at nominal Mach numbers of 2.5, 3.0, 3.5, and 4.0. The flat plate boundary layer initially was laminar and became transitional in the measurement region. The experimentally determined convective heat transfer coefficients were generally higher than the theoretical predictions for flat plate laminar boundary layers. However, the results indicate that this nonintrusive optical measurement technique has the potential to measure surface convective heat transfer coefficients in high-speed flowfields.
A laser-induced heat flux technique for convective heat transfer measurements in high speed flows
NASA Technical Reports Server (NTRS)
Porro, A. R.; Keith, T. G., Jr.; Hingst, W. R.
1991-01-01
A technique is developed to measure the local convective heat transfer coefficient on a model surface in a supersonic flow field. The technique uses a laser to apply a discrete local heat flux at the model test surface, and an infrared camera system determines the local temperature distribution due to the heating. From this temperature distribution and an analysis of the heating process, a local convective heat transfer coefficient is determined. The technique was used to measure the local surface convective heat transfer coefficient distribution on a flat plate at nominal Mach numbers of 2.5, 3.0, 3.5, and 4.0. The flat plate boundary layer initially was laminar and became transitional in the measurement region. The experimentally determined convective heat transfer coefficients were generally higher than the theoretical predictions for flat plate laminar boundary layers. However, the results indicate that this nonintrusive optical measurement technique has the potential to measure surface convective heat transfer coefficients in high speed flow fields.
NASA Astrophysics Data System (ADS)
Taler, Dawid
2012-09-01
This paper presents a numerical method for determining heat transfer coefficients in cross-flow heat exchangers with extended heat exchange surfaces. Coefficients in the correlations defining heat transfer on the liquid- and air-side were determined using a nonlinear regression method. Correlation coefficients were determined from the condition that the sum of squared liquid and air temperature differences at the heat exchanger outlet, obtained by measurements and those calculated, achieved minimum. Minimum of the sum of the squares was found using the Levenberg-Marquardt method. The uncertainty in estimated parameters was determined using the error propagation rule by Gauss. The outlet temperature of the liquid and air leaving the heat exchanger was calculated using the analytical model of the heat exchanger.
Low heat transfer, high strength window materials
Berlad, Abraham L.; Salzano, Francis J.; Batey, John E.
1978-01-01
A multi-pane window with improved insulating qualities; comprising a plurality of transparent or translucent panes held in an essentially parallel, spaced-apart relationship by a frame. Between at least one pair of panes is a convection defeating means comprising an array of parallel slats or cells so designed as to prevent convection currents from developing in the space between the two panes. The convection defeating structures may have reflective surfaces so as to improve the collection and transmittance of the incident radiant energy. These same means may be used to control (increase or decrease) the transmittance of solar energy as well as to decouple the radiative transfer between the interior surfaces of the transparent panes.
Artamonova, Irena I; Lappi, Tanya; Zudina, Liudmila; Mushegian, Arcady R
2015-07-01
Assessment of phylogenetic positions of predicted gene and protein sequences is a routine step in any genome project, useful for validating the species' taxonomic position and for evaluating hypotheses about genome evolution and function. Several recent eukaryotic genome projects have reported multiple gene sequences that were much more similar to homologues in bacteria than to any eukaryotic sequence. In the spirit of the times, horizontal gene transfer from bacteria to eukaryotes has been invoked in some of these cases. Here, we show, using comparative sequence analysis, that some of those bacteria-like genes indeed appear likely to have been horizontally transferred from bacteria to eukaryotes. In other cases, however, the evidence strongly indicates that the eukaryotic DNA sequenced in the genome project contains a sample of non-integrated DNA from the actual bacteria, possibly providing a window into the host microbiome. Recent literature suggests also that common reagents, kits and laboratory equipment may be systematically contaminated with bacterial DNA, which appears to be sampled by metagenome projects non-specifically. We review several bioinformatic criteria that help to distinguish putative horizontal gene transfers from the admixture of genes from autonomously replicating bacteria in their hosts' genome databases or from the reagent contamination. PMID:25919787
Effect of radiator position and mass flux on the dryer room heat transfer rate
NASA Astrophysics Data System (ADS)
Mirmanto, M.; Sulistyowati, E. D.; Okariawan, I. D. K.
A room radiator as usually used in cold countries, is actually able to be used as a heat source to dry goods, especially in the rainy season where the sun seldom shines due to much rain and cloud. Experiments to investigate effects of radiator position and mass flux on heat transfer rate were performed. This study is to determine the best position of the radiator and the optimum mass flux. The radiator used was a finned radiator made of copper pipes and aluminum fins with an overall dimension of 220 mm × 50 mm × 310 mm. The prototype room was constructed using plywood and wood frame with an overall size of 1000 mm × 1000 mm × 1000 mm. The working fluid was heated water flowing inside the radiator and air circulating naturally inside the prototype room. The nominal mass fluxes employed were 800, 900 and 1000 kg/m2 s. The water was kept at 80 °C at the radiator entrance, while the initial air temperature inside the prototype room was 30 °C. Three positions of the radiator were examined. The results show that the effect of the mass flux on the forced and free convection heat transfer rate is insignificant but the radiator position strongly affects the heat transfer rate for both forced and free convection.
Options: the JADE reactor and heat transfer by heat pipes
Simpson, J.E.; Massey, J.V.
1981-08-10
The JADE reactor is a new Lawrence Livermore National Laboratory (LLNL) concept which maintains advantages of liquid metal walls and addresses some of their problems. The concept envisions a porous medium, called the jade, of specific geometry lining the reactor cavity. The jade is designed to convert the kinetic energy of the fluid to thermal energy before it reaches the first wall. Finally, its particular geometric shape is used to minimize reaction forces on the first wall due to blow-off caused by soft x-rays and debris, to provide empty spaces for fluid expansion after neutron energy deposition where droplets collide with droplets cancelling their kinetic energies, and to provide large surface areas for rapid condensation of vapor. LLNL also suggested that heat pipes might be used to eliminate portions of the primary or secondary coolant loops, thereby reducing pumping requirements found in current reactor designs.
Heat transfer in vertically aligned phase change energy storage systems
El-Dessouky, H.T.; Bouhamra, W.S.; Ettouney, H.M.; Akbar, M.
1999-05-01
Convection effects on heat transfer are analyzed in low temperature and vertically aligned phase change energy storage systems. This is performed by detailed temperature measurements in the phase change material (PCM) in eighteen locations forming a grid of six radial and three axial positions. The system constitutes a double pipe configuration, where commercial grade paraffin wax is stored in the annular space between the two pipes and water flows inside the inner pipe. Vertical alignment of the system allowed for reverse of the flow direction of the heat transfer fluid (HTF), which is water. Therefore, the PCM is heated from the bottom for HTF flow from bottom to top and from the top as the HTF flow direction is reversed. For the former case, natural convection affects the melting process. Collected data are used to study variations in the transient temperature distribution at axial and radial positions as well as for the two-dimensional temperature field. The data are used to calculate the PCM heat transfer coefficient and to develop correlations for the melting Fourier number. Results indicate that the PCM heat transfer coefficient is higher for the case of PCM heating from bottom to top. Nusselt number correlations are developed as a function of Rayleigh, Stefan, and Fourier numbers for the HTF flow from bottom to top and as a function of Stefan and Fourier numbers for HTF flow from top to bottom. The enhancement ratio for heat transfer caused by natural convection increases and then levels off as the inlet temperature of the HTF is increased.
Multidimensional mechanistic modeling of interfacial heat and mass transfer
Shaver, D. R.; Antal, S. P.; Podowski, M. Z.
2012-07-01
A combined theoretical and computational study in modeling multidimensional, diabatic vapor/liquid flows is presented. Models have been developed governing kinematic aspects of multiphase flow as well as interfacial mass and heat transfer for flows of condensable gas (vapor) and liquids. The modeling formulation is based on the Reynolds averaged Navier-Stokes (RANS) type multi-field approach which utilizes a complete set of conservation equations for each fluid component 1. The modeled interfacial interactions include energy, mass, and momentum transfer. Emphasis in the model development work has been placed on the mechanisms governing coupled interfacial heat and mass transfer between the liquid and vapor fields (condensation and/or boiling). A method for tracking changes in bubble size is presented and tested. Locally based models of multidimensional effects have been analyzed, including distributions of fluid temperatures and volume fractions. The overall model accounts for both kinematic and thermodynamic nonequilibrium between the component fluids including superheated vapor. The model has been implemented in the NPHASE-CMFD computer code. Results from the kinematic model are compared to experimental data and good agreement is demonstrated. The heat and mass transfer model is parametrically tested to show the multidimensional effects on the rate of heat and mass transfer. These effects are explained in terms of local characteristics of the two-phase flow. The model is applied to a scenario of saturated vapor injected into a subcooled flow through a heated, porous wall. This provides a reasonable approximation to subcooled boiling. The results are found to be dependent on the partitioning of the wall heat flux between direct liquid heating and vapor generation. However, the observed dependencies are explained and the modeling is considered consistent. (authors)
Heat Transfer in High-Temperature Fibrous Insulation
NASA Technical Reports Server (NTRS)
Daryabeigi, Kamran
2002-01-01
The combined radiation/conduction heat transfer in high-porosity, high-temperature fibrous insulations was investigated experimentally and numerically. The effective thermal conductivity of fibrous insulation samples was measured over the temperature range of 300-1300 K and environmental pressure range of 1.33 x 10(exp -5)-101.32 kPa. The fibrous insulation samples tested had nominal densities of 24, 48, and 72 kilograms per cubic meter and thicknesses of 13.3, 26.6 and 39.9 millimeters. Seven samples were tested such that the applied heat flux vector was aligned with local gravity vector to eliminate natural convection as a mode of heat transfer. Two samples were tested with reverse orientation to investigate natural convection effects. It was determined that for the fibrous insulation densities and thicknesses investigated no heat transfer takes place through natural convection. A finite volume numerical model was developed to solve the governing combined radiation and conduction heat transfer equations. Various methods of modeling the gas/solid conduction interaction in fibrous insulations were investigated. The radiation heat transfer was modeled using the modified two-flux approximation assuming anisotropic scattering and gray medium. A genetic-algorithm based parameter estimation technique was utilized with this model to determine the relevant radiative properties of the fibrous insulation over the temperature range of 300-1300 K. The parameter estimation was performed by least square minimization of the difference between measured and predicted values of effective thermal conductivity at a density of 24 kilograms per cubic meters and at nominal pressures of 1.33 x 10(exp -4) and 99.98 kPa. The numerical model was validated by comparison with steady-state effective thermal conductivity measurements at other densities and pressures. The numerical model was also validated by comparison with a transient thermal test simulating reentry aerodynamic heating
A numerical study of vorticity-enhanced heat transfer
NASA Astrophysics Data System (ADS)
Wang, Xiaolin; Alben, Silas
2012-11-01
The Glezer lab at Georgia Tech has found that vorticity produced by vibrated reeds can improve heat transfer in electronic hardware. Vortices enhance forced convection by boundary layer separation and thermal mixing in the bulk flow. In this work, we simulate the heat transfer process in a 3-dimensional plate-fin heat sink. We propose a simplified model by considering flow and temperature in a 2-D channel, and extend the model to the third dimension using a 1-D heat fin model. We simulate periodically steady-state solutions. We determine how the global Nusselt number is increased, depending on the vortices' strengths and spacings, in the parameter space of Reynolds and Peclet numbers. We find a surprising spatial oscillation of the local Nusselt number due to the vortices. Support from NSF-DMS grant 1022619 is acknowledged.
Transient heat transfer program for glovebox process vessels
Preuss, D.E.; Frigo, A.A.; Bailey, J.L.
1997-09-01
A software program has been developed at Argonne National Laboratory to aid in designing process vessels to be used in gloveboxes. The Transient Heat Transfer Program for Glovebox Process Vessels provides engineers with a method of analyzing the heat transfer characteristics of vessels during heating and cooling of metals, salts, and other materials. The user need only provide information on the components and geometry of the vessel and a few operating conditions. The program approximates the changes in the internal vessel temperature over a number of time steps. This temperature information can then be used to estimate parameters that are needed in the vessel design. These parameters include insulation thickness, amount of heat shielding, and heater size. This software has been designed for ease of use. A background in the thermal sciences is not necessary to use it.
Heat transfer characteristics of the fluidized bed through the annulus
NASA Astrophysics Data System (ADS)
Shedid, Mohamed H.; Hassan, M. A. M.
2015-11-01
The annular fluidized bed can be regarded as a promising technique for waste heat recovery applications. This study investigates on the determination of steady state values of the average heat transfer on the surface of the inner tube under different operating conditions that include: (1) input heat flux ranging from 557 to 1671 W/m2, (2) superficial air velocity ranging between 0.12 and 0.36 m/s, (3) initial bed height ranging from 25 to 55 cm, (4) ratio of the inner to the outer diameters ranging from 1/6 to 1/2 and Kaolin particle diameters ranging between 282 and 550 µm. The average values of the heat transfer coefficient along the inner tube (consisting of the fluidized and free board sections) are also deduced. An empirical correlation for calculating the Nusselt number is obtained for the given parameters and ranges.
Local jet impingement boiling heat transfer with R113
NASA Astrophysics Data System (ADS)
Zhou, D. W.; Ma, C. F.
An experimental study was performed to characterize the boiling heat transfer of impinging circular submerged jets on simulated microelectronic chips with a nominal area of 5 mm × 5 mm. The heat transfer modes included natural convection, partially developed nucleate boiling, fully developed nucleate boiling and critical heat flux. The study included the effects of jet parameters and fluid subcooling on the nucleate boiling. The results showed that the nucleate boiling data varied only with fluid subcooling regardless of jet parameters and that both the pool and impingement nucleate boiling curves at the same subcooling condition were well correlated. The high heat flux portions of the boiling curves with jet exit velocities greater than 10 m/s were corrected for the elevated saturation temperature. A new expression was developed with an interpolation method to construct the partially developed nucleate boiling curve.
Enhancement and Suppression of Heat Transfer by MHD Turbulence
NASA Astrophysics Data System (ADS)
Lazarian, A.
2006-07-01
We study the effect of turbulence on heat transfer within magnetized plasmas for energy injection velocities both larger and smaller than the Alfvén speed. We find that in the latter regime the heat transfer is partially suppressed, while in the former regime the effects of turbulence depend on the intensity of driving. In fact, the scale lA at which the turbulent velocity is equal to the Alfvén velocity is an important new parameter. When the electron mean free path λ is larger than lA, the stronger the turbulence, the lower the thermal conductivity by electrons. The turbulent motions, however, induce their own advective heat transport, which, for the parameters of intracluster medium, provides effective heat diffusivity that exceeds the classical Spitzer value.
NASA Astrophysics Data System (ADS)
Zipf, Verena; Willert, Daniel; Neuhäuser, Anton
2016-05-01
An innovative active latent heat storage concept was invented and developed at Fraunhofer ISE. It uses a screw heat exchanger (SHE) for the phase change during the transport of a phase change material (PCM) from a cold to a hot tank or vice versa. This separates heat transfer and storage tank in comparison to existing concepts. A test rig has been built in order to investigate the heat transfer coefficients of the SHE during melting and crystallization of the PCM. The knowledge of these characteristics is crucial in order to assess the performance of the latent heat storage in a thermal system. The test rig contains a double shafted SHE, which is heated or cooled with thermal oil. The overall heat transfer coefficient U and the convective heat transfer coefficient on the PCM side hPCM both for charging and discharging have been calculated based on the measured data. For charging, the overall heat transfer coefficient in the tested SHE was Uch = 308 W/m2K and for discharging Udis = 210 W/m2K. Based on the values for hPCM the overall heat transfer coefficients for a larger SHE with steam as heat transfer fluid and an optimized geometry were calculated with Uch = 320 W/m2K for charging and Udis = 243 W/m2K for discharging. For pressures as high as p = 100 bar, an SHE concept has been developed, which uses an organic fluid inside the flight of the SHE as working media. With this concept, the SHE can also be deployed for very high pressure, e.g. as storage in solar thermal power plants.
Measurement of capsule heat transfer gaps using neutron radiography
NASA Technical Reports Server (NTRS)
Thaler, L. A.
1974-01-01
A technique is described for measuring heat transfer gaps from neutron radiographs. The method involves scanning the radiograph negative with a recording microdensitometer to obtain a trace of the optical density variation across the diameter of the capsule. The optical density change representing the gap is measured from the microdensitometer trace and related to the physical measurement. Heat transfer gaps from 0.061 to 0.178 cm have been determined by this technique and agree with preassembly physical measurements to plus or minus 0.005 cm.
Radiative heat transfer in 2D Dirac materials
Rodriguez-López, Pablo; Tse, Wang -Kong; Dalvit, Diego A. R.
2015-05-12
We compute the radiative heat transfer between two sheets of 2D Dirac materials, including topological Chern insulators and graphene, within the framework of the local approximation for the optical response of these materials. In this approximation, which neglects spatial dispersion, we derive both numerically and analytically the short-distance asymptotic of the near-field heat transfer in these systems, and show that it scales as the inverse of the distance between the two sheets. In conclusion, we discuss the limitations to the validity of this scaling law imposed by spatial dispersion in 2D Dirac materials.
Stagnation-point heat transfer correlation for ionized gases
NASA Technical Reports Server (NTRS)
Bade, W. L.
1975-01-01
Based on previous laminar boundary-layer solutions for argon, xenon, nitrogen, and air, it is shown that the effect of gas ionization on stagnation-point heat transfer can be correlated with the variation of the frozen Prandtl number across the boundary layer. A formula is obtained for stagnation-point heat transfer in a noble gas and is shown to be valid from the low-temperature range to the region of strong ionization. It is concluded that the considered effect can be well correlated by the 0.7 power of the Prandtl-number ratio across the boundary layer.
Heat transfer effects during cold dense gas dispersion
NASA Astrophysics Data System (ADS)
Andreiev, G.; Neff, D. E.; Meroney, R. N.
1983-11-01
Wind tunnel concentration data were obtained for continuous area releases of isothermal, cold N2, cold CO2 and cold CH4 clouds. Wind tunnel results were compared to field test results and to a computer model simulation. Heat transfer and humidity effects on model concentration distributions were significant for methane plumes when surface Richardson numbers, Ri, were large (i.e., low wind speed and high boiloff rates conditions). At field scales heat transfer and humidity still play a role in the dispersion of methane spill cases, but plume dilution and lift off are not as exaggerated as for the model cases.
Predicted Turbine Heat Transfer for a Range of Test Conditions
NASA Technical Reports Server (NTRS)
Boyle, R. J.; Lucci, B. L.
1996-01-01
Comparisons are shown between predictions and experimental data for blade and endwall heat transfer. The comparisons of computational domain parisons are given for both vane and rotor geometries over an extensive range of Reynolds and Mach numbers. Comparisons are made with experimental data from a variety of sources. A number of turbulence models are available for predicting blade surface heat transfer, as well as aerodynamic performance. The results of an investigation to determine the turbulence model which gives the best agreement with experimental data over a wide range of test conditions are presented.
Heat transfer education : Keeping it relevant and vibrant.
Khounsary, A. M.
1998-08-14
The motivation for a fresh look at heat transfer education, both in content and in methodology, is generated by a number of trends in engineering practice. These include the increasing demand for engineers with interdisciplinary skills, rapid integration of technology, emergence of computerized and interactive problem-solving tools, shortening time of concept-to-market, availability of new technologies, and an increasing number of new or redesigned products and processes in which heat transfer plays a part. Examination of heat transfer education in this context can be aided by considering the changes, both qualitatively and quantitatively, in the student, educator, and researcher populations, employment opportunities, in the needs of corporations, government, industry, and universities, and in the relevant technical problems and issues of the day. Such an overview provides the necessary background for charting a response to the difficult question of how to maintain excellence and continuity in heat transfer education in the face of rapid, widespread, and complex changes. The present paper addresses how to make heat transfer education more relevant and stimulating. This paper represents a written summary of a 1996 panel discussion at the 1996 International Mechanical Engineering Conference and Exhibition (IMECE) of the American Society of Mechanical Engineers (ASME) in Atlanta, Georgia, on ''Heat Transfer Education: Keeping it Relevant and Vibrant,'' with significant expansion and amplification by the authors and the panelists in the 1997-98 period. The consensus of the participants is that the steps necessary to ensure the desired outcome in heat transfer education should include: (1) a better understanding of the interaction between the student, course content, and market needs; (2) an appreciation of the need in multidisciplinary industrial environments for engineers trained with a broad background: (3) a revision of the introductory heat transfer course to
Simulation of turbulent heat transfer in a rotating duct
NASA Astrophysics Data System (ADS)
Dutta, Sandip; Andrews, Malcolm J.; Han, Je-Chin
1995-04-01
The turbulent heat transfer in a rotating duct is simulated using a modified k-epsilon model. The standard k-epsilon model which includes the Coriolis and rotational buoyancy effects in the momentum equations was not used due to the fact that there are no corresponding terms in the k and epsilon transport equations. The modified model on the other hand adds turbulence production and dissipation from the Coriolis and buoyancy effects. The results show that these modifications are necessary to obtain reasonable predictions or rotational heat transfer effects in the cooling channels of a turbine blade.
Computation of Radiation Heat Transfer in Aeroengine Combustors
NASA Technical Reports Server (NTRS)
Patankar, S. V.
1996-01-01
In this report the highlights of the research completed for the NASA are summarized. This research has been completed in the form of two Ph.D. theses by Chai (1994) and Parthasarathy (1996). Readers are referred to these theses for a complete details of the work and lists of references. In the following sections, first objectives of this research are introduced, then the finite-volume method for radiation heat transfer is described, and finally computations of radiative heat transfer in non-gray participating media is presented.
Heat Transfer from a Horizontal Cylinder Rotating in Oil
NASA Technical Reports Server (NTRS)
Seban, R. A.; Johnson, H. A.
1959-01-01
Measurements of the heat transfer from a horizontal cylinder rotating about its axis have been made with oil as the surrounding fluid to provide an addition to the heat-transfer results for this system heretofore available only for air. The results embrace a Prandtl number range from about 130 to 660, with Reynolds numbers up to 3 x 10(exp 4), and show an increasing dependence of free-convection heat transfer on rotation as the Prandtl number is increased by reducing the oil temperature. Some correlation of this effect, which agrees with the prior results for air, has been achieved. At higher rotative speeds the flow becomes turbulent, the free- convection effect vanishes, and the results with oil can be correlated generally with those for air and with mass-transfer results for even higher Prandtl numbers. For this system, however, the analogy calculations which have successfully related the heat transfer to the friction for pipe flows at high Prandtl numbers fail.
Electrical control and enhancement of boiling heat transfer during quenching
NASA Astrophysics Data System (ADS)
Shahriari, Arjang; Hermes, Mark; Bahadur, Vaibhav
2016-02-01
Heat transfer associated with boiling degrades at elevated temperatures due to the formation of an insulating vapor layer at the solid-liquid interface (Leidenfrost effect). Interfacial electrowetting (EW) fields can disrupt this vapor layer to promote liquid-surface wetting. We experimentally analyze EW-induced disruption of the vapor layer and measure the resulting enhanced cooling during the process of quenching. Imaging is employed to visualize the fluid-surface interactions and understand boiling patterns in the presence of an electrical voltage. It is seen that EW fields fundamentally change the boiling pattern, wherein a stable vapor layer is replaced by intermittent wetting of the surface. Heat conduction across the vapor gap is thus replaced with transient convection. This fundamental switch in the heat transfer mode significantly accelerates cooling during quenching. An order of magnitude increase in the cooling rate is observed, with the heat transfer seen approaching saturation at higher voltages. An analytical model is developed to extract voltage dependent heat transfer rates from the measured cooling curve. The results show that electric fields can alter and tune the traditional cooling curve. Overall, this study presents an ultralow power consumption concept to control the mechanical properties and metallurgy, by electrically tuning the cooling rate during quenching.
Combined heat and mass transfer device for improving separation process
Tran, Thanh Nhon
1999-01-01
A two-phase small channel heat exchange matrix simultaneously provides for heat transfer and mass transfer between the liquid and vapor phases of a multi-component mixture at a single, predetermined location within a separation column, significantly improving the thermodynamic efficiency of the separation process. The small channel heat exchange matrix is composed of a series of channels having a hydraulic diameter no greater than 5.0 millimeters for conducting a two-phase coolant. In operation, the matrix provides the liquid-vapor contacting surfaces within the separation column, such that heat and mass are transferred simultaneously between the liquid and vapor phases. The two-phase coolant allows for a uniform heat transfer coefficient to be maintained along the length of the channels and across the surface of the matrix. Preferably, a perforated, concave sheet connects each channel to an adjacent channel to facilitate the flow of the liquid and vapor phases within the column and to increase the liquid-vapor contacting surface area.
Combined heat and mass transfer device for improving separation process
Tran, T.N.
1999-08-24
A two-phase small channel heat exchange matrix simultaneously provides for heat transfer and mass transfer between the liquid and vapor phases of a multi-component mixture at a single, predetermined location within a separation column, significantly improving the thermodynamic efficiency of the separation process. The small channel heat exchange matrix is composed of a series of channels having a hydraulic diameter no greater than 5.0 millimeters for conducting a two-phase coolant. In operation, the matrix provides the liquid-vapor contacting surfaces within the separation column, such that heat and mass are transferred simultaneously between the liquid and vapor phases. The two-phase coolant allows for a uniform heat transfer coefficient to be maintained along the length of the channels and across the surface of the matrix. Preferably, a perforated, concave sheet connects each channel to an adjacent channel to facilitate the flow of the liquid and vapor phases within the column and to increase the liquid-vapor contacting surface area. 12 figs.
Enhanced boiling heat transfer in horizontal test bundles
Trewin, R.R.; Jensen, M.K.; Bergles, A.E.
1994-08-01
Two-phase flow boiling from bundles of horizontal tubes with smooth and enhanced surfaces has been investigated. Experiments were conducted in pure refrigerant R-113, pure R-11, and mixtures of R-11 and R-113 of approximately 25, 50, and 75% of R-113 by mass. Tests were conducted in two staggered tube bundles consisting of fifteen rows and five columns laid out in equilateral triangular arrays with pitch-to-diameter ratios of 1.17 and 1.5. The enhanced surfaces tested included a knurled surface (Wolverine`s Turbo-B) and a porous surface (Linde`s High Flux). Pool boiling tests were conducted for each surface so that reference values of the heat transfer coefficient could be obtained. Boiling heat transfer experiments in the tube bundles were conducted at pressures of 2 and 6 bar, heat flux values from 5 to 80 kW/m{sup 2}s, and qualities from 0% to 80%, Values of the heat transfer coefficients for the enhanced surfaces were significantly larger than for the smooth tubes and were comparable to the values obtained in pool boiling. It was found that the performance of the enhanced tubes could be predicted using the pool boiling results. The degradation in the smooth tube heat transfer coefficients obtained in fluid mixtures was found to depend on the difference between the molar concentration in the liquid and vapor.
The heat transfer characteristics of lightning return stroke channel
NASA Astrophysics Data System (ADS)
Dong, Caixia; Yuan, Ping; Cen, Jianyong; Wang, Xuejuan; Mu, Yali
2016-09-01
Based on the time-resolved spectra of lightning return stroke processes, the evolutional characteristics of thermal conductivity and thermal diffusivity of the discharge channels are discussed. The distribution of temperature along the radial direction of channels at the peak current stage of return stroke is also investigated, and then the heat transferring characteristics along radial direction of the channels are analyzed. The results show that a temperature gradient along radial direction of lightning channel is formed due to the outward heat transfer. The closer the distance is to the current core channel, the greater the temperature gradient is and the more heat is transferred along the radial direction of the channel. The heat transferring in per unit length of the channel and per unit time is in the order of 104 J/m ṡ s at the initial moment of lightning return stroke. After the peak current, the channel temperature decreases slowly and the heat transport coefficients vary as a monotonically decreasing function.
Improved boundary layer heat transfer calculations near a stagnation point
NASA Technical Reports Server (NTRS)
Ahn, Kyung Hwan
1990-01-01
A thermal design of a solar receiver has been developed for the solutions of problems involving phase-change thermal energy storage and natural convection loss. Two dimensional axisymmetrical solidification and melting of materials contained between two concentric cylinders of finite length has been studied for thermal energy storage analysis. For calculation of free convection loss inside receiver cavity, two dimensional axisymmetrical, laminar, transient free convection including radiation effects has been studied using integral/finite difference method. Finite difference equations are derived for the above analysis subject to constant or variable material properties, initial conditions, and boundary conditions. The validity of the analyses has been substantiated by comparing results of the present general method with available analytic solutions or numerical results reported in the literature. Both explicit and implicit schemes are tested in phase change analysis with different number of nodes ranging from 4 to 18. The above numerical methods have been applied to the existing solar receiver analyzing computer code as additional subroutines. The results were computed for one of the proposed Brayton cycle solar receiver models running under the actual environmental conditions. Effect of thermal energy storage on the thermal behavior of the receiver has been estimated. Due to the thermal energy storage, about 65% reduction on working gas outlet temperature fluctuation has been obtained; however, maximum temperature of thermal energy storage containment has been increased about 18%. Also, effect of natural convection inside a receiver cavity on the receiver heat transfer has been analyzed. The finding indicated that thermal stratification occurs during the sun time resulting in higher receiver temperatures at the outlet section of the gas tube, and lower temperatures at the inlet section of the gas tube when compared with the results with no natural convection. Due
Heat-transfer tests of aqueous ethylene glycol solutions in an electrically heated tube
NASA Technical Reports Server (NTRS)
Bernardo, Everett; Eian, Carroll S
1945-01-01
As part of an investigation of the cooling characteristics of liquid-cooled engines, tests were conducted with an electrically heated single-tube heat exchanger to determine the heat-transfer characteristics of an-e-2 ethylene glycol and other ethylene glycol-water mixtures. Similar tests were conducted with water and commercial butanol (n-butyl alcohol) for check purposes. The results of tests conducted at an approximately constant liquid-flow rate of 0.67 pound per second (Reynolds number, 14,500 to 112,500) indicate that at an average liquid temperature 200 degrees f, the heat-transfer coefficients obtained using water, nominal (by volume) 30 percent-70 percent and 70 percent-30 percent glycol-water mixtures are approximately 3.8, 2.8, and 1.4 times higher, respectively, than the heat-transfer coefficients obtained using an-e-2 ethylene glycol.
Theory of heat transfer and hydraulic resistance of oil radiators
NASA Technical Reports Server (NTRS)
Mariamov, N B
1942-01-01
In the present report the coefficients of heat transfer and hydraulic resistance are theoretically obtained for the case of laminar flow of a heated viscous liquid in a narrow rectangular channel. The results obtained are applied to the computation of oil radiators, which to a first approximation may be considered as made up of a system of such channels. In conclusion, a comparison is given of the theoretical with the experimental results obtained from tests on airplane oil radiators.
Phonon-assisted heat transfer between vacuum-separated surfaces
NASA Astrophysics Data System (ADS)
Pendry, J. B.; Sasihithlu, K.; Craster, R. V.
2016-08-01
With increasing interest in nanotechnology, the question arises of how heat is exchanged between materials separated by only a few nanometers of vacuum. Here, we present calculations of the contribution of phonons to heat transfer mediated by van der Waals forces and compare the results to other mechanisms such as coupling through near field fluctuations. Our results show a more dramatic decay with separation than previous work.
Characterization of heat transfer in nutrient materials, part 2
NASA Technical Reports Server (NTRS)
Cox, J. E.; Bannerot, R. B.; Chen, C. K.; Witte, L. C.
1973-01-01
A thermal model is analyzed that takes into account phase changes in the nutrient material. The behavior of fluids in low gravity environments is discussed along with low gravity heat transfer. Thermal contact resistance in the Skylab food heater is analyzed. The original model is modified to include: equivalent conductance due to radiation, radial equivalent conductance, wall equivalent conductance, and equivalent heat capacity. A constant wall-temperature model is presented.
Heat transfer simulation in a helically coiled tube steam generator
NASA Astrophysics Data System (ADS)
Hassanzadeh, Bazargan; Keshavarz, Ali; Ebrahimi, Masood
2014-01-01
A symmetric helically coiled tube steam generator that operates by methane has been simulated analytically and numerically. In the analytical method, the furnace has been divided into five zones. The numerical method computes the total heat absorbed in the furnace, while the existing analytical methods compute only the radiation heat transfer. In addition, according to the numerical results, a correlation is proposed for the Nusselt number in the furnace.
Bell, J H; Hand, L A
2005-04-21
The growth rate of a crystal in a supersaturated solution is limited by both reaction kinetics and the local concentration of solute. If the local mass transfer coefficient is too low, concentration of solute at the crystal-solution interface will drop below saturation, leading to a defect in the growing crystal. Here, mass transfer coefficients are calculated for a rotating crystal growing in a supersaturated solution of potassium diphosphate (KDP) in water. Since mass transfer is difficult to measure directly, the heat transfer coefficient of a scale model crystal in water is measured using temperature-sensitive paint (TSP). To the authors' knowledge this is the first use of TSP to measure temperatures in water. The corresponding mass transfer coefficient is then calculated using the Chilton- Colburn analogy. Measurements were made for three crystal sizes at two running conditions each. Running conditions include periodic reversals of rotation direction. Heat transfer coefficients were found to vary significantly both across the crystal faces and over the course of a rotation cycle, but not from one face to another. Mean heat transfer coefficients increased with both crystal size and rotation rate. Computed mass transfer coefficients were broadly in line with expectations from the full-scale crystal growth experiments. Additional experiments show that continuous rotation of the crystal results in about a 30% lower heat transfer compared to rotation with periodic reversals. The continuous rotation case also shows a periodic variation in heat transfer coefficient of about 15%, with a period about 1/20th of the rotation rate.
Overall Heat and Mass Transfer Coefficient of Water Vapor Adsorption
NASA Astrophysics Data System (ADS)
Hamamoto, Yoshinori; Mori, Hideo; Godo, Masazumi; Miura, Kunio; Watanabe, Yutaka; Ishizawa, Toshihiko; Takatsuka, Takeshi
A fundamental investigation was performed to develop a compact and simple desiccant ventilation unit which is one of the main components of a novel energy saving air-conditioning system. Water vapor in the air is adsorbed and/or desorbed to be controlled the humidity of supply air through a unit of an adsorbent packed bed. A numerical simulation helps to understand the phenomena of heat and mass transfer in the bed. Overall transfer coefficients of them as properties for the simulation were estimated by performing both experiment and calculation. It was clarified that the transient overall equivalent heat and mass transfer does not strongly depend on the air flow rate through the packed bed, the averaged equivalent mass transfer is governed by surface and pore diffusion in a particle of adsorbent at low flow rate. Moreover, the coefficient during the adsorption process is slightly larger than desorption. An equation of the overall mass transfer coefficient is derived. It shows five times as large as the value estimated by experiment. Therefore, the correlation and fitting parameters are presented for prediction of the overall heat and mass transfer coefficients. The estimation accuracy was improved.
Two Heat-Transfer Improvements for Gas Liquefiers
NASA Technical Reports Server (NTRS)
Martin, Jerry L.
2005-01-01
Two improvements in heat-transfer design have been investigated with a view toward increasing the efficiency of refrigerators used to liquefy gases. The improvements could contribute to the development of relatively inexpensive, portable oxygen liquefiers for medical use. A description of the heat-transfer problem in a pulse-tube refrigerator is prerequisite to a meaningful description of the first improvement. In a pulse-tube refrigerator in particular, one of in-line configuration heat must be rejected from two locations: an aftercooler (where most of the heat is rejected) and a warm heat exchanger (where a small fraction of the total input power must be rejected as heat). Rejection of heat from the warm heat exchanger can be problematic because this heat exchanger is usually inside a vacuum vessel. When an acoustic-inertance tube is used to provide a phase shift needed in the pulse-tube cooling cycle, another problem arises: Inasmuch as the acoustic power in the acoustic-inertance tube is dissipated over the entire length of the tube, the gas in the tube must be warmer than the warm heat exchanger in order to reject heat at the warm heat exchanger. This is disadvantageous because the increase in viscosity with temperature causes an undesired increase in dissipation of acoustic energy and an undesired decrease in the achievable phase shift. Consequently, the overall performance of the pulse-tube refrigerator decreases with increasing temperature in the acoustic-inertance tube. In the first improvement, the acoustic-inertance tube is made to serve as the warm heat exchanger and to operate in an approximately isothermal condition at a lower temperature, thereby increasing the achievable phase shift and the overall performance of the refrigerator. This is accomplished by placing the acoustic-inertance tube inside another tube and pumping a cooling fluid (e.g., water) in the annular space between the tubes. Another benefit of this improvement is added flexibility of
Heat Transfer Capacity of Lotus-Type Porous Copper Heat Sink
NASA Astrophysics Data System (ADS)
Chiba, Hiroshi; Ogushi, Tetsuro; Nakajima, Hideo; Ikeda, Teruyuki
Lotus-type porous copper is a form of copper that includes many straight pores, which are produced by the precipitation of supersaturated gas dissolved in the molten metal during solidification. The lotus-type porous copper is attractive as a heat sink because a higher heat transfer capacity is obtained as the pore diameter decreases. We investigate a fin model for predicting the heat transfer capacity of the lotus-type porous copper. Its heat transfer capacity is verified to be predictable via the straight fin model, in which heat conduction in the porous metal and the heat transfer to the fluid in the pores are taken into consideration by comparison with a numerical analysis. We both experimentally and analytically determine the heat transfer capacities of three types of heat sink: with conventional groove fins, with groove fins that have a smaller fin gap (micro-channels) and with lotus-type porous copper fins. The conventional groove fins have a fin gap of 3mm and a fin thickness of 1mm, the micro-channels have a fin gap of 0.5mm and a fin thickness of 0.5mm, and the lotus-type porous copper fins have pores with a diameter of 0.3mm and a porosity of 0.39. The lotus-type porous copper fins were found to have a heat transfer capacity 4 times greater than the conventional groove fins and 1.3 times greater than the micro-channel heat sink under the same pumping power.
Nanofluid Flow and Heat Transfer in Channel Entrance Region
NASA Astrophysics Data System (ADS)
Liu, Joseph T. C.; Puliti, Gianluca
2014-11-01
The present work uses the continuum description of nanofluid flow to study the flow, heat and mass transfer in the entrance and developing region of channels or tubes, where the viscous and heat conduction layers are thin and the heat transfer is much more intense than fully developed flow. Instead of supplementing the formulation with thermodynamic properties based on mixture calculations, use is made of recent molecular dynamical computations of such properties, specifically, the density and heat capacity of gold-water nanofluids. The more general formulation results, within the Rayleigh-Stokes (plug flow) approximation and perturbation for small volume fraction, show that the nanofluid density-heat capacity has an enormous effect in the inertia mechanism in causing the nanofluid temperature profile to steepen. The nanofluid thermal conductivity though has an explicit enhancement of the surface heat transfer rate has the almost hidden effect of stretching the nanofluid temperature profile thus giving the opposite effect of enhancement. Quantitative results for Gold-Water nanofluid is presented.
Numerical prediction of turbulent oscillating flow and associated heat transfer
NASA Astrophysics Data System (ADS)
Koehler, W. J.; Patankar, S. V.; Ibele, W. E.
1991-08-01
A crucial point for further development of engines is the optimization of its heat exchangers which operate under oscillatory flow conditions. It has been found that the most important thermodynamic uncertainties in the Stirling engine designs for space power are in the heat transfer between gas and metal in all engine components and in the pressure drop across the heat exchanger components. So far, performance codes cannot predict the power output of a Stirling engine reasonably enough if used for a wide variety of engines. Thus, there is a strong need for better performance codes. However, a performance code is not concerned with the details of the flow. This information must be provided externally. While analytical relationships exist for laminar oscillating flow, there has been hardly any information about transitional and turbulent oscillating flow, which could be introduced into the performance codes. In 1986, a survey by Seume and Simon revealed that most Stirling engine heat exchangers operate in the transitional and turbulent regime. Consequently, research has since focused on the unresolved issue of transitional and turbulent oscillating flow and heat transfer. Since 1988, the University of Minnesota oscillating flow facility has obtained experimental data about transitional and turbulent oscillating flow. However, since the experiments in this field are extremely difficult, lengthy, and expensive, it is advantageous to numerically simulate the flow and heat transfer accurately from first principles. Work done at the University of Minnesota on the development of such a numerical simulation is summarized.
Numerical prediction of turbulent oscillating flow and associated heat transfer
NASA Technical Reports Server (NTRS)
Koehler, W. J.; Patankar, S. V.; Ibele, W. E.
1991-01-01
A crucial point for further development of engines is the optimization of its heat exchangers which operate under oscillatory flow conditions. It has been found that the most important thermodynamic uncertainties in the Stirling engine designs for space power are in the heat transfer between gas and metal in all engine components and in the pressure drop across the heat exchanger components. So far, performance codes cannot predict the power output of a Stirling engine reasonably enough if used for a wide variety of engines. Thus, there is a strong need for better performance codes. However, a performance code is not concerned with the details of the flow. This information must be provided externally. While analytical relationships exist for laminar oscillating flow, there has been hardly any information about transitional and turbulent oscillating flow, which could be introduced into the performance codes. In 1986, a survey by Seume and Simon revealed that most Stirling engine heat exchangers operate in the transitional and turbulent regime. Consequently, research has since focused on the unresolved issue of transitional and turbulent oscillating flow and heat transfer. Since 1988, the University of Minnesota oscillating flow facility has obtained experimental data about transitional and turbulent oscillating flow. However, since the experiments in this field are extremely difficult, lengthy, and expensive, it is advantageous to numerically simulate the flow and heat transfer accurately from first principles. Work done at the University of Minnesota on the development of such a numerical simulation is summarized.
Heat transfer of ascending cryomagma on Europa
NASA Astrophysics Data System (ADS)
Quick, Lynnae C.; Marsh, Bruce D.
2016-06-01
Jupiter's moon Europa has a relatively young surface (60-90 Myr on average), which may be due in part to cryovolcanic processes. Current models for both effusive and explosive cryovolcanism on Europa may be expanded and enhanced by linking the potential for cryovolcanism at the surface to subsurface cryomagmatism. The success of cryomagma transport through Europa's crust depends critically on the rate of ascent relative to the rate of solidification. The final transport distance of cryomagma is thus governed by initial melt volume, ascent rate, overall ascent distance, transport mechanism (i.e., diapirism, diking, or ascent in cylindrical conduits), and melt temperature and composition. The last two factors are especially critical in determining the budget of expendable energy before complete solidification. Here we use these factors as constraints to explore conditions under which cryomagma may arrive at Europa's surface to facilitate cryovolcanism. We find that 1-5 km radius warm ice diapirs ascending from the base of a 10 km thick stagnant lid can reach the shallow subsurface in a partially molten state. Cryomagma transport may be further facilitated if diapirs travel along pre-heated ascent paths. Under certain conditions, cryolava transported from 10 km depths in tabular dikes or pipe-like conduits may reach the surface at temperatures exceeding 250 K. Ascent rates for these geometries may be high enough that isothermal transport is approached. Cryomagmas containing significant amounts of low eutectic impurities can also be delivered to Europa's surface by propagating dikes or pipe-like conduits.
Wildemeersch, S; Jamin, P; Orban, P; Hermans, T; Klepikova, M; Nguyen, F; Brouyère, S; Dassargues, A
2014-11-15
Geothermal energy systems, closed or open, are increasingly considered for heating and/or cooling buildings. The efficiency of such systems depends on the thermal properties of the subsurface. Therefore, feasibility and impact studies performed prior to their installation should include a field characterization of thermal properties and a heat transfer model using parameter values measured in situ. However, there is a lack of in situ experiments and methodology for performing such a field characterization, especially for open systems. This study presents an in situ experiment designed for estimating heat transfer parameters in shallow alluvial aquifers with focus on the specific heat capacity. This experiment consists in simultaneously injecting hot water and a chemical tracer into the aquifer and monitoring the evolution of groundwater temperature and concentration in the recovery well (and possibly in other piezometers located down gradient). Temperature and concentrations are then used for estimating the specific heat capacity. The first method for estimating this parameter is based on a modeling in series of the chemical tracer and temperature breakthrough curves at the recovery well. The second method is based on an energy balance. The values of specific heat capacity estimated for both methods (2.30 and 2.54MJ/m(3)/K) for the experimental site in the alluvial aquifer of the Meuse River (Belgium) are almost identical and consistent with values found in the literature. Temperature breakthrough curves in other piezometers are not required for estimating the specific heat capacity. However, they highlight that heat transfer in the alluvial aquifer of the Meuse River is complex and contrasted with different dominant process depending on the depth leading to significant vertical heat exchange between upper and lower part of the aquifer. Furthermore, these temperature breakthrough curves could be included in the calibration of a complex heat transfer model for
Numerical Analysis of Heat Transfer Characteristics in Microwave Heating of Magnetic Dielectrics
NASA Astrophysics Data System (ADS)
Peng, Zhiwei; Hwang, Jiann-Yang; Park, Chong-Lyuck; Kim, Byoung-Gon; Onyedika, Gerald
2012-03-01
A numerical simulation of heat transfer during the microwave heating process of magnetite, which is a two-dimensional (2-D) magnetic dielectric, subjected to heat conduction, convection, and radiation was performed. The heat transfer process was modeled using an explicit finite-difference approach, and the temperature profiles for different heating parameters were generated through developing a code in Mathematica 7.0 (Wolfram Research, Inc., Champaign, IL). The temperature in the sample increases rapidly in 1 minute and nonuniform temperature distribution inside the object is observed. An obvious temperature hot spot is formed in the corner of the predicted temperature profile initially, which shifts to the center of the object as heating power increases. Microwave heating at 915 MHz exhibits better heating uniformity than 2450 MHz mainly because of the larger microwave penetration depth. It is also observed that the heating homogeneity in the object can be improved by reducing the dimension of object. The effects of heating time, microwave power, microwave frequency, and object dimension need to be considered to obtain high heating performance and avoid/minimize thermal runaway resulting from temperature nonuniformity in large-scale microwave heating.
ERIC Educational Resources Information Center
Rojas-Trigos, J. B.; Bermejo-Arenas, J. A.; Marin, E.
2012-01-01
In this paper, some heat transfer characteristics through a sample that is uniformly heated on one of its surfaces by a power density modulated by a periodical square wave are discussed. The solution of this problem has two contributions, comprising a transient term and an oscillatory term, superposed to it. The analytical solution is compared to…
Heat transfer analysis of the passive residual heat removal system in ROSA/AP600 experiments
Yonomoto, Taisuke; Kukita, Yutaka; Schultz, R.R.
1998-10-01
The passive residual heat removal (PRHR) system in the Westinghouse AP600 advanced passive reactor design is a natural-circulation-driven heat exchanger cooled by the water in the in-containment refueling water storage tank (IRWST). During the experiments, which simulated small-break loss-of-coolant accidents in the AP600 reactor using the ROSA-V Large-Scale Test Facility (LSTF), the PRHR system heat removal rates well exceeded the core decay power soon after the actuation of the PRHR. This resulted in continuous cooldown and depressurization of the primary side. The PRHR heat transfer performance in these experiments was analyzed by applying heat transfer correlations available in literature to the PRHR heat exchanger tube bundle. Also, the three-dimensional natural circulation in the IRWST was simulated numerically using the FLUENT code. The total heat transfer rate of the PRHR was predicted within 5% of the measured value. The fluid temperature distribution in the IRWST was also predicted well except that the elevation of the thermally stratified region was underpredicted. The calculated flow pattern in the IRWST suggests that the atypical IRWST geometry in the LSTF may have affected the PRHR heat transfer performance during the experiments only a little.