Science.gov

Sample records for actual operating results

  1. Northrop Triga facility decommissioning plan versus actual results

    SciTech Connect

    Gardner, F.W.

    1986-01-01

    This paper compares the Triga facility decontamination and decommissioning plan to the actual results and discusses key areas where operational activities were impacted upon by the final US Nuclear Regulatory Commission (NRC)-approved decontamination and decommissioning plan. Total exposures for fuel transfer were a factor of 4 less than planned. The design of the Triga reactor components allowed the majority of the components to be unconditionally released.

  2. Experimental study on the regenerator under actual operating conditions

    NASA Astrophysics Data System (ADS)

    Nam, Kwanwoo; Jeong, Sangkwon

    2002-05-01

    An experimental apparatus was prepared to investigate thermal and hydrodynamic characteristics of the regenerator under its actual operating conditions. The apparatus included a compressor to pressurize and depressurize regenerator with various operating frequencies. Cold end of the regenerator was maintained around 100 K by means of liquid nitrogen container and heat exchanger. Instantaneous gas temperature and mass flow rate were measured at both ends of the regenerator during the whole pressure cycle. Pulsating pressure and pressure drop across the regenerator were also measured. The operating frequency of the pressure cycle was varied between 3 and 60 Hz, which are typical operating frequencies of Gifford-McMahon, pulse tube, and Stirling cryocoolers. First, friction factor for the wire screen mesh was directly determined from room temperature experiments. When the operating frequency was less than 9 Hz, the oscillating flow friction factor was nearly same as the steady flow friction factor for Reynolds number up to 100. For 60 Hz operations, the ratio of oscillating flow friction factor to steady flow one was increased as hydraulic Reynolds number became high. When the Reynolds number was 100, this ratio was about 1.6. Second, ineffectiveness of the regenerator was obtained when the cold-end was maintained around 100 K and the warm-end at 300 K to simulate the actual operating condition of the regenerator in cryocooler. Effect of the operating frequency on ineffectiveness of regenerator was discussed at low frequency range.

  3. GOSAT TANSO operation results

    NASA Astrophysics Data System (ADS)

    Nakajima, Masakatsu; Kuze, Akiihiko; Suto, Hiroshi; Shiomi, Kei

    2010-05-01

    The Greenhouse gases Observing SATellite (GOSAT) observes carbon dioxide (CO2) and methane (CH4) globally from space. It was launched on January 23, 2009 from Tanegashima Space Center. Since February 7, 2009, the Thermal And Near infrared Sensor for carbon Observation Fourier-Transform Spectrometer (TANSO-FTS) and Cloud and Aerosol Imager (TANSO-CAI) have been continuously operated. They acquire global data every three days. For the first six months after the launch, on-orbit function, performance, calibration, and validation have been checked-out. The brief summary of instrument design, pre-launch test results, observation plan (grid and sun glint observation and special target mode), onboard calibration schemes, and the initial on-orbit results of radiometric, geometric and spectroscopic performances are presented. TANSO-FTS Level 1A and 1B data processing algorithm and its updates on the ground are also presented. In addition we will show recent on orbit instrument status such as pointing accuracy, interferogram quality, and radiometric accuracy.

  4. Life extension of elevated-temperature reactors considering actual operating conditions

    SciTech Connect

    Ziada, H.H.

    1993-01-01

    Many reactors have experienced operating conditions less severe than those specified in the design. Their actual operating conditions may involve fewer or less severe transients, lower operating temperatures, or a combination of these. Thus the actual operating conditions become important considerations in efforts to extend the life of reactor components. If the number of transients experienced is fewer than the number specified in the design, the actual transients must be reconstructed to determine extended life. When operating temperature is below 800 [degrees]F, fatigue damage becomes the controlling factor in life assessment. At operating temperatures above 800 [degrees]F (e.g., breeder reactors), creep damage becomes another controlling factor because residual stresses have a longer time for relaxation, a fact that will reduce creep damage. This study presents an approach to assessing the life of breeder reactor components when the actual transients are fewer in number than those specified in the design. It also discusses the sensitivity of creep-fatigue damage in such factors when actual operating temperatures and the actual severity of transients fall below the design specifications.

  5. Life extension of elevated-temperature reactors considering actual operating conditions

    SciTech Connect

    Ziada, H.H.

    1993-01-01

    Many reactors have experienced operating conditions less severe than those specified in the design. Their actual operating conditions may involve fewer or less severe transients, lower operating temperatures, or a combination of these. Thus the actual operating conditions become important considerations in efforts to extend the life of reactor components. If the number of transients experienced is fewer than the number specified in the design, the actual transients must be reconstructed to determine extended life. When operating temperature is below 800 {degrees}F, fatigue damage becomes the controlling factor in life assessment. At operating temperatures above 800 {degrees}F (e.g., breeder reactors), creep damage becomes another controlling factor because residual stresses have a longer time for relaxation, a fact that will reduce creep damage. This study presents an approach to assessing the life of breeder reactor components when the actual transients are fewer in number than those specified in the design. It also discusses the sensitivity of creep-fatigue damage in such factors when actual operating temperatures and the actual severity of transients fall below the design specifications.

  6. Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 2

    NASA Technical Reports Server (NTRS)

    Keitz, J. F.

    1982-01-01

    The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 2 of the four major tasks included in the study. Task 2 compares various catagories of flight plans and flight tracking data produced by a simulation system developed for the Federal Aviation Administrations by SRI International. (Flight tracking data simulate actual flight tracks of all aircraft operating at a given time and provide for rerouting of flights as necessary to resolve traffic conflicts.) The comparisons of flight plans on the forecast to flight plans on the verifying analysis confirm Task 1 findings that wind speeds are generally underestimated. Comparisons involving flight tracking data indicate that actual fuel burn is always higher than planned, in either direction, and even when the same weather data set is used. Since the flight tracking model output results in more diversions than is known to be the case, it was concluded that there is an error in the flight tracking algorithm.

  7. Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning: Summary report

    NASA Technical Reports Server (NTRS)

    Keitz, J. F.

    1982-01-01

    The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This summary report discusses the results of each of the four major tasks of the study. Task 1 compared airline flight plans based on operational forecasts to plans based on the verifying analyses and found that average fuel savings of 1.2 to 2.5 percent are possible with improved forecasts. Task 2 consisted of similar comparisons but used a model developed for the FAA by SRI International that simulated the impact of ATc diversions on the flight plans. While parts of Task 2 confirm the Task I findings, inconsistency with other data and the known impact of ATC suggests that other Task 2 findings are the result of errors in the model. Task 3 compares segment weather data from operational flight plans with the weather actually observed by the aircraft and finds the average error could result in fuel burn penalties (or savings) of up to 3.6 percent for the average 8747 flight. In Task 4 an in-depth analysis of the weather forecast for the 33 days included in the study finds that significant errors exist on 15 days. Wind speeds in the area of maximum winds are underestimated by 20 to 50 kts., a finding confirmed in the other three tasks.

  8. 33 CFR 142.4 - Duties of lessees, permittees, and persons responsible for actual operations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Duties of lessees, permittees, and persons responsible for actual operations. 142.4 Section 142.4 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES...

  9. Actual evapotranspiration modeling using the operational Simplified Surface Energy Balance (SSEBop) approach

    USGS Publications Warehouse

    Savoca, Mark E.; Senay, Gabriel B.; Maupin, Molly A.; Kenny, Joan F.; Perry, Charles A.

    2013-01-01

    Remote-sensing technology and surface-energy-balance methods can provide accurate and repeatable estimates of actual evapotranspiration (ETa) when used in combination with local weather datasets over irrigated lands. Estimates of ETa may be used to provide a consistent, accurate, and efficient approach for estimating regional water withdrawals for irrigation and associated consumptive use (CU), especially in arid cropland areas that require supplemental water due to insufficient natural supplies from rainfall, soil moisture, or groundwater. ETa in these areas is considered equivalent to CU, and represents the part of applied irrigation water that is evaporated and/or transpired, and is not available for immediate reuse. A recent U.S. Geological Survey study demonstrated the application of the remote-sensing-based Simplified Surface Energy Balance (SSEB) model to estimate 10-year average ETa at 1-kilometer resolution on national and regional scales, and compared those ETa values to the U.S. Geological Survey’s National Water-Use Information Program’s 1995 county estimates of CU. The operational version of the operational SSEB (SSEBop) method is now used to construct monthly, county-level ETa maps of the conterminous United States for the years 2000, 2005, and 2010. The performance of the SSEBop was evaluated using eddy covariance flux tower datasets compiled from 2005 datasets, and the results showed a strong linear relationship in different land cover types across diverse ecosystems in the conterminous United States (correlation coefficient [r] ranging from 0.75 to 0.95). For example, r for woody savannas (0.75), grassland (0.75), forest (0.82), cropland (0.84), shrub land (0.89), and urban (0.95). A comparison of the remote-sensing SSEBop method for estimating ETa and the Hamon temperature method for estimating potential ET (ETp) also was conducted, using regressions of all available county averages of ETa for 2005 and 2010, and yielded correlations of r = 0

  10. Comparison of ASSESS neutralization module results with actual small force engagement outcomes

    SciTech Connect

    Gardner, B.H.; Snell, M.K.; Paulus, W.K. )

    1991-01-01

    The ASSESS Neutralization module (Neutralization) is part of the Analytic System and Software for Evaluation of Safeguards and Security (ASSESS), a vulnerability assessment tool. Neutralization models a fire fight between security inspectors (SIs) and adversaries. This paper reports that a comparison has been made between actual outcomes of police and small military engagements and the results predicted by the Neutralization module for similar scenarios. The results of this comparison show a surprising correlation between predicted outcomes (based on numbers of combatants, weapon types, and exposures, etc.) and the actual outcomes of the engagements analyzed. The importance of this analysis is that given the defenders have intelligence on actual adversary characteristics or are protecting against a design basis threat, defense capabilities can be evaluated before an engagement. Results could then be used to develop a favorable probability of a desired outcome. For example, law enforcement agencies are frequently able to compile the number of criminals, types of weaponry, willingness to use force, etc., from analysis of crime scenes.

  11. VGOS operations and geodetic results

    NASA Astrophysics Data System (ADS)

    Niell, A. E.; Beaudoin, C. J.

    2013-12-01

    The next generation geodetic VLBI instrument is being developed with a goal of 1 mm position uncertainty in twenty-four hours. The broadband signal chain, which is essential for obtaining the required delay accuracy from a network of relatively small antennas, has been implemented on the 12 meter antenna at Goddard Space Flight Center, Maryland, USA, and on the 18 meter Westford antenna at Haystack Observatory, Massachusetts, USA. Several observing sessions have been carried out to evaluate and demonstrate system performance as new capabilities are implemented. The first twenty-four hour session was conducted in 2013 May during which several new features of the VGOS system were demonstrated. These include automated data acquisition under Field System control, which will be essential for unattended operation. For that session more than 1100 observations were made at a rate of 48 scans per hour, a factor of three higher than for current geodetic sessions. This high density of observations is one of the main goals of the new systems and is expected to lead to better estimation of the atmosphere delays, a primary error source limiting the geodetic accuracy. To compensate for the smaller antennas needed for the high slew rates, the radio-frequency signals were recorded in four bands spanning 3.2 GHz to 8.8 GHz at a total data rate of 8 Gigabits per second. The total data volume at each site was about 40 Terabytes. Because of potential damage to the VLBI receiver from the Satellite Laser Ranging system aircraft avoidance radar at GSFC, observations within a 40 degree cone to the south of the VLBI site in the direction of the SLR were masked out. This loss of sky coverage increases the uncertainty in the site position estimate relative to that which could be made with full sky coverage. Geodetic results from this and subsequent sessions will be reported.

  12. Optimization of CCGT power plant and performance analysis using MATLAB/Simulink with actual operational data.

    PubMed

    Hasan, Naimul; Rai, Jitendra Nath; Arora, Bharat Bhushan

    2014-01-01

    In the Modern scenario, the naturally available resources for power generation are being depleted at an alarming rate; firstly due to wastage of power at consumer end, secondly due to inefficiency of various power system components. A Combined Cycle Gas Turbine (CCGT) integrates two cycles- Brayton cycle (Gas Turbine) and Rankine cycle (Steam Turbine) with the objective of increasing overall plant efficiency. This is accomplished by utilising the exhaust of Gas Turbine through a waste-heat recovery boiler to run a Steam Turbine. The efficiency of a gas turbine which ranges from 28% to 33% can hence be raised to about 60% by recovering some of the low grade thermal energy from the exhaust gas for steam turbine process. This paper is a study for the modelling of CCGT and comparing it with actual operational data. The performance model for CCGT plant was developed in MATLAB/Simulink. PMID:24936394

  13. Actual Performance Prediction of Split-type Room Air Conditioner which Considered Unsteady Operation Concerning Heat Island Problem

    NASA Astrophysics Data System (ADS)

    Shinomiya, Naruaki; Nishimura, Nobuya; Iyota, Hiroyuki; Nomura, Tomohiro

    Split type air conditioners are operated actually in the situation unlike the condition that was described in a product catalog. On the other hand, exhaust heat from air conditioner is considered as one of the causes of heat island problem in urban area, and the air conditioner performance and heat load affect exhaust heat amount. In this study, air conditioner performances in both standard summer day and severe hot day were examined by dynamic simulation which considered outdoor weather changes. As a result, actual performances of the air conditioner were demonstrated as a function of outdoor temperature, heat load and indoor temperature. The higher the outdoor temperature and heat load rise, the smaller influences of indoor temperature against COP became. In standard summer day, relative performance exceeded by 15 to 45% than that of JIS operating condition. Also, COP in severe hot day decreased about 6% at the peak time than that of standard day. As a result, the air conditioner exhaust heat during one day which was predicted by the proposed simulation model became about 16% smaller than the conventional prediction model.

  14. Analysis of Actual Operating Conditions of an Off-grid Solid Oxide Fuel Cell

    SciTech Connect

    Dennis Witmer; Thomas Johnson; Jack Schmid

    2008-12-31

    Fuel cells have been proposed as ideal replacements for other technologies in remote locations such as Rural Alaska. A number of suppliers have developed systems that might be applicable in these locations, but there are several requirements that must be met before they can be deployed: they must be able to operate on portable fuels, and be able to operate with little operator assistance for long periods of time. This project was intended to demonstrate the operation of a 5 kW fuel cell on propane at a remote site (defined as one without access to grid power, internet, or cell phone, but on the road system). A fuel cell was purchased by the National Park Service for installation in their newly constructed visitor center at Exit Glacier in the Kenai Fjords National Park. The DOE participation in this project as initially scoped was for independent verification of the operation of this demonstration. This project met with mixed success. The fuel cell has operated over 6 seasons at the facility with varying degrees of success, with one very good run of about 1049 hours late in the summer of 2006, but in general the operation has been below expectations. There have been numerous stack failures, the efficiency of electrical generation has been lower than expected, and the field support effort required has been far higher than expected. Based on the results to date, it appears that this technology has not developed to the point where demonstrations in off road sites are justified.

  15. Bridging the gap between empirical results, actual strategies, and developmental programs in soccer.

    PubMed

    Figueiredo, António J; Gonçalves, Carlos E; Tessitore, Antonio

    2014-05-01

    Being one of the most prominent globalized sports, soccer played at club, national, and continental levels has a relevant societal role. At present, the specific competencies, interests, and languages of the different actors involved in the selection, development, and support of long-lasting careers of players might limit opportunities for potential talented players. Unless the cultural environment of soccer resolves the gaps between empirical results and actual soccer strategies, scientific discussion relating to the effectiveness of talent selection and development remains limited. This commentary is intended to highlight the need for developmental programs to prepare soccer personnel for a transdisciplinary dialogue, which could foster a future development of this sport. Finally, in considering the wide soccer-related employment opportunities at local, national, and international levels, the need for a clear qualification framework is crucial. PMID:24755978

  16. Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 3

    NASA Technical Reports Server (NTRS)

    Keitz, J. F.

    1982-01-01

    The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 3 of the four major tasks included in the study. Task 3 compares flight plans developed on the Suitland forecast with actual data observed by the aircraft (and averaged over 10 degree segments). The results show that the average difference between the forecast and observed wind speed is 9 kts. without considering direction, and the average difference in the component of the forecast wind parallel to the direction of the observed wind is 13 kts. - both indicating that the Suitland forecast underestimates the wind speeds. The Root Mean Square (RMS) vector error is 30.1 kts. The average absolute difference in direction between the forecast and observed wind is 26 degrees and the temperature difference is 3 degree Centigrade. These results indicate that the forecast model as well as the verifying analysis used to develop comparison flight plans in Tasks 1 and 2 is a limiting factor and that the average potential fuel savings or penalty are up to 3.6 percent depending on the direction of flight.

  17. Actual defect observation results of an extreme-ultraviolet blank mask by coherent diffraction imaging

    NASA Astrophysics Data System (ADS)

    Harada, Tetsuo; Hashimoto, Hiraku; Amano, Tsuyoshi; Kinoshita, Hiroo; Watanabe, Takeo

    2016-03-01

    Extreme-ultraviolet (EUV) lithography poses a number of challenges, one of which is the production of a defect-free mask. To observe the defects on an EUV mask in a quantitative phase image, we have developed a microcoherent EUV scatterometry microscope. The intensity and phase images of the defects are reconstructed using ptychography. We observe four actual defects on an EUV blank mask using the microscope. The reconstructed shapes of the actual defects correspond well to those measured by atomic force microscopy (AFM). Our microscope should therefore function as an essential review tool in characterizing defects.

  18. Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 1

    NASA Technical Reports Server (NTRS)

    Keitz, J. F.

    1982-01-01

    The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 1 of the four major tasks included in the study. Task 1 compares flight plans based on forecasts with plans based on the verifying analysis from 33 days during the summer and fall of 1979. The comparisons show that: (1) potential fuel savings conservatively estimated to be between 1.2 and 2.5 percent could result from using more timely and accurate weather data in flight planning and route selection; (2) the Suitland forecast generally underestimates wind speeds; and (3) the track selection methodology of many airlines operating on the North Atlantic may not be optimum resulting in their selecting other than the optimum North Atlantic Organized Track about 50 percent of the time.

  19. Forest Landowner Education Interests and Delivery Preferences: A Retrospective Look at Survey Results and Actual Participation

    ERIC Educational Resources Information Center

    Zobrist, Kevin W.; Rozance, Mary Ann

    2015-01-01

    This article presents survey data on education interests and delivery preferences of small forest landowners in Washington and compares it to actual program participation over 6 years. The survey was conducted in late 2007 to guide development and implementation of a Extension forestry program. The survey found broad interest across many topics…

  20. Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 4

    NASA Technical Reports Server (NTRS)

    Keitz, J. F.

    1982-01-01

    The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 4 of the four major tasks included in the study. Task 4 uses flight plan segment wind and temperature differences as indicators of dates and geographic areas for which significant forecast errors may have occurred. An in-depth analysis is then conducted for the days identified. The analysis show that significant errors occur in the operational forecast on 15 of the 33 arbitrarily selected days included in the study. Wind speeds in an area of maximum winds are underestimated by at least 20 to 25 kts. on 14 of these days. The analysis also show that there is a tendency to repeat the same forecast errors from prog to prog. Also, some perceived forecast errors from the flight plan comparisons could not be verified by visual inspection of the corresponding National Meteorological Center forecast and analyses charts, and it is likely that they are the result of weather data interpolation techniques or some other data processing procedure in the airlines' flight planning systems.

  1. Selection of the most advantageous gas turbine air filtration system: Comparative study of actual operating experience

    SciTech Connect

    Gilani, S.I.; Mehr, M.Z.

    1985-01-01

    This paper discusses relative merits of three types of air filtration systems used by Sui Northern Gas Pipelines Ltd. (Pakistan), on its gas turbine compressor packages. These Filtration systems are: (i) Two stage inertial plus auto oil bath type multi-duty filters by AAF used on Saturn Mark-1 packages manufactured by Solar Turbines Inc. (ii) Three stage high efficiency barrier filters by AAF used on Centaur packages by Solar. (iii) Single stage pulse-jet self-cleaning filter by Donaldson again used on a Centaur package. The selection is primarily based in package performance data collected over a 15 month period analyzing power loss due to fouling effects and related operation and maintenance costs for the three systems. The Company's operating experience indicates that on new installations the pulse clean system offers the best advantage both in terms of filtration costs as well as availability of additional horse power when operating under moderate to severe environmental conditions.

  2. Operational actual wetland evapotranspiration estimation for the Everglades using MODIS imagery

    NASA Astrophysics Data System (ADS)

    Melesse, Assefa; Cereon, Cristobal

    2014-05-01

    Wetlands are one of the most important ecosystems with varied functions and structures. Humans have drained wetlands and altered the structure and functions of wetlands for various uses. Wetland restoration efforts require assessment of the level of ecohydrological restoration for the intended functions. Among the various indicators of success in wetland restoration, achieving the desired water level (hydrology) is the most important, faster to achieve and easier to monitor than the establishment of the hydric soils and wetland vegetation. Monitoring wetland hydrology using remote sensing based evapotranspiration (ET) is a useful tool and approach since point measurements for understanding the temporal (before and after restoration) and spatial (impacted and restored) parts of the wetland are not effective for large areas. Evapotranspiration accounts over 80% of the water budget of the wetlands necessitating the need for spatiotemporal monitoring of ET flux. A study employing remotely sensed data from Moderate Resolution Imaging Spectroradiometer (MODIS) and modeling tools was conducted for a weekly spatial estimation of Everglades ET. Weekly surface temperature data were generated from the MODIS thermal band and evaporative fraction was estimated using the simplified surface energy balance (SSEB) approach. Based on the Simple Method, potential ET (PET) was estimated. Actual weekly wetland ET was computed as the (product of the PET and evaporative fraction). The ET product will be useful information for environmental restoration and wetland hydrology managers. The on-going restoration and monitoring work in the Everglades will benefit from this product and assist in evaluating progress and success in the restoration.

  3. Actual operation and regulatory activities on steam generator replacement in Japan

    SciTech Connect

    Saeki, Hitoshi

    1997-02-01

    This paper summarizes the operating reactors in Japan, and the status of the steam generators in these plants. It reviews plans for replacement of existing steam generators, and then goes into more detail on the planning and regulatory steps which must be addressed in the process of accomplishing this maintenance. The paper also reviews the typical steps involved in the process of removal and replacement of steam generators.

  4. Actual Condition Evaluation of Cogeneration System in an Urbanized Hotel, and Study of the Optimal Operation to Minimize the CO2 Emission

    NASA Astrophysics Data System (ADS)

    Katsuta, Masafumi; Kaneko, Akira; Yamamoto, Toru

    Recently, there is an important subject to reduce of the CO2 emission discharged from a building. A cogeneration system (CGS) is one of the effective facilities to reduce of the CO2 emission, but prudent consideration is required in design and operation. Because it is necessary to be matching electric demand and heat demand in order to obtain the high efficiency. In this paper, it is evaluated the power generation efficiency and heat recovery one of CGS in the actual urbanized hotel as measurement result. In addition, the optimal operation analysis is carried out in order to minimize CO2 emission in the present facility.

  5. Operational results from the LHC luminosity monitors

    SciTech Connect

    Miyamoto, R.; Ratti, A.; Matis, H.S.; Stezelberger, T.; Turner, W.C.; Yaver, H.; Bravin, E.

    2011-03-28

    The luminosity monitors for the high luminosity regions in the LHC have been operating to monitor and optimize the luminosity since 2009. The device is a gas ionization chamber inside the neutral particle absorber 140 m from the interaction point and monitors showers produced by high energy neutral particles from the collisions. It has the ability to resolve the bunch-by-bunch luminosity as well as to survive the extreme level of radiation in the nominal LHC operation. We present operational results of the device during proton and lead ion operations in 2010 and make comparisons with measurements of experiments. The Large Hadron Collider (LHC) at CERN can accelerate proton and lead ion beams to 7 TeV and 547 TeV and produce collisions of these particles. Luminosity measures performance of the LHC and is particularly important for experiments in high luminosity interaction points (IPs), ATLAS (IP1) and CMS (IP5). To monitor and optimize the luminosities of these IPs, BRAN (Beam RAte Neutral) detectors [1, 2] have been installed and operating since the beginning of the 2009 operation [3]. A neutral particle absorber (TAN) protects the D2 separation dipole from high energy forward neutral particles produced in the collisions [4]. These neutral particles produce electromagnetic and hadronic showers inside the TAN and their energy flux is proportional to the collision rate and hence to the luminosity. The BRAN detector is an Argon gas ionization chamber installed inside the TANs on both sides of the IP1 and IP5 and monitors the relative changes in the luminosity by detecting the ionization due to these showers. When the number of collisions per bunch crossing (multiplicity) is small, the shower rate inside the TAN is also proportional to the luminosity. Hence, the detector is designed to operate by measuring either the shower rate (counting mode for low and intermediate luminosities) or the average shower flux (pulse height mode for high luminosities). The detector is

  6. Tunka-133: Results of 3 year operation

    NASA Astrophysics Data System (ADS)

    Prosin, V. V.; Berezhnev, S. F.; Budnev, N. M.; Chiavassa, A.; Chvalaev, O. A.; Gress, O. A.; Dyachok, A. N.; Epimakhov, S. N.; Karpov, N. I.; Kalmykov, N. N.; Konstantinov, E. N.; Korobchenko, A. V.; Korosteleva, E. E.; Kozhin, V. A.; Kuzmichev, L. A.; Lubsandorzhiev, B. K.; Lubsandorzhiev, N. B.; Mirgazov, R. R.; Panasyuk, M. I.; Pan'kov, L. V.; Popova, E. G.; Ptuskin, V. S.; Semeney, Yu. A.; Silaev, A. A.; Silaev, A. A.; Skurikhin, A. V.; Spiering, C.; Sveshnikova, L. G.; Yashin, I. V.; Zagorodnikov, A. V.

    2014-08-01

    The EAS Cherenkov light array Tunka-133, with ~3 km2 geometric area, is taking data since 2009. The array permits a detailed study of cosmic ray energy spectrum and mass composition in the PeV energy range. After a short description of the methods of EAS parameter reconstruction, we present the all-particle energy spectrum and results of studying CR composition, based on 3 seasons of array operation. In the last part of the paper, we discuss possible interpretations of the obtained results.

  7. Wind Plant Capacity Credit Variations: A Comparison of Results Using Multiyear Actual and Simulated Wind-Speed Data

    SciTech Connect

    Milligan, M.

    1997-06-01

    Although it is widely recognized that variations in annual wind energy capture can be significant, it is not clear how significant this effect is on accurately calculating the capacity credit of a wind plant. An important question is raised concerning whether one year of wind data is representative of long-term patters. This report calculates the range of capacity credit measures based on 13 years of actual wind-speed data. The results are compared to those obtained with synthetic data sets that are based on one year of data. Although the use of synthetic data sets is a considerable improvement over single-estimate techniques, this report finds that the actual inter-annual variation in capacity credit is still understated by the synthetic data technique.

  8. Wind plant capacity credit variations: A comparison of results using multiyear actual and simulated wind-speed data

    SciTech Connect

    Milligan, M.R.

    1997-12-31

    Although it is widely recognized that variations in annual wind energy capture can be significant, it is not clear how significant this effect is on accurately calculating the capacity credit of a wind plant. An important question is raised concerning whether one year of wind data is representative of long-term patterns. This paper calculates the range of capacity credit measures based on 13 years of actual wind-speed data. The results are compared to those obtained with synthetic data sets that are based on one year of data. Although the use of synthetic data sets is a considerable improvement over single-estimate techniques, this paper finds that the actual inter-annual variation in capacity credit is still understated by the synthetic data technique.

  9. Lessons Learned from Eight Years' Experience of Actual Operation, and Future Prospects of JMA Earthquake Early Warning System

    NASA Astrophysics Data System (ADS)

    Hoshiba, M.; Nishimae, Y.

    2015-12-01

    Since 2007, experiences of actual operation of EEW have been gained by the Japan Meteorological Agency (JMA). During this period, we have learned lessons from many M6- and M7-class earthquakes, and the Mw9.0 Tohoku earthquake. During the Mw9.0 Tohoku earthquake, JMA system functioned well: it issued a warning message more than 15 s before strong ground shaking in the Tohoku district (relatively near distance from the epicenter). However, it was not perfect: in addition to the problem of large extent of fault rupture, some false warning messages were issued due to the confusion of the system because of simultaneous multiple aftershocks which occurred at the wide rupture area. To address the problems, JMA will introduce two new methods into the operational system this year to start their tests, aiming at practical operation within a couple of years. One is Integrated Particle Filter (IPF) method, which is an integrated algorithm of multiple hypocenter determination techniques with Bayesian estimation, in which amplitude information is also used for hypocenter determination. The other is Propagation of Local Undamped Motion (PLUM) method, in which warning message is issued when strong ground shaking is detected at nearby stations around the target site (e.g., within 30 km). Here, hypocenter and magnitude are not required in PLUM. Aiming at application for several years later, we are investigating a new approach, in which current wavefield is estimated in real time, and then future wavefield is predicted time evolutionally from the current situation using physics of wave propagation. Here, hypocenter and magnitude are not necessarily required, but real-time observation of ground shaking is necessary. JMA also plans to predict long period ground motion (up to 8 s) with the EEW system for earthquake damage mitigation in high-rise buildings. Its test will start using the operational system in the near future.

  10. SOFIA tracking subsystem: results of assembly, operation, and calibration tests

    NASA Astrophysics Data System (ADS)

    Bittner, Hermann; Erdmann, Matthias; Schmolke, Juergen; Lattner, Klaus; Levin, Torsten; Erhard, Markus

    2003-02-01

    The SOFIA airborne telescope has a Tracking Subsystem for stellar acquisition, tracking, and pointing. The system has three high-performance imagers: the boresighted wide field (6 degrees FOV) and fine field imagers (70 arcminutes FOV), and the main-telescope-optics sharing focal plane imager (8 arcminutes FOV). The imagers are controlled by 3 CCD head controllers, an overall imager controller, and a tracker controller providing the tracking error signals from the objects observed by the imagers. There have been several test steps in the assembly, integration, and verification of the Tracking Subsystem. The paper presents the fully integrated system as actually built, the results of the thermal-vacuum and vibration tests of the fine field imager, the tested operational/functional S/W performance, as well as the results of the geometric and radiometric calibrations of the imagers.

  11. Operation results of the DIOS pilot plant

    SciTech Connect

    Ishikawa, Minoru

    1996-12-31

    DIOS, the Direct Iron Ore Smelting Reduction Process, is now reaching the final stage of its research and development program. The aim of the project is to establish a substitutive or a supplementary industrial iron making process for the blast furnace process. Four campaigns, from the third to sixth, of 500 t/d pilot plant testing operation were conducted in the 1994 fiscal year, from April 1994 to March 1995. Furthermore, the seventh to tenth campaigns were conducted in the 1995 fiscal year. From the sixth to tenth campaign were conducted with a smelting reduction furnace partially installed water cooled panels. Testing operations of high production rate using several kinds of coal with different volatile matter contents were carried out. A material flow has been still more improved to realize a stable coupling operation of integrated furnaces, i.e., a preheating furnace, PRF1, a prereduction furnace, PRF2 and a smelting reduction furnace, SRF. These testing operations were conducted in a joint research project of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation with a subsidy for promoting coal production and utilization technologies from the Agency of Natural Resources and Energy, MITI.

  12. Recent result of gyrotron operation in NIFS

    NASA Astrophysics Data System (ADS)

    Ito, Satoshi; Shimozuma, Takashi; Yoshimura, Yasuo; Igami, Hiroe; Takahashi, Hiromi; Nishiura, Masaki; Kobayashi, Sakuji; Mizuno, Yoshinori; Okada, Kota; Kubo, Shin

    2015-03-01

    In the last Large Helical Device (LHD) experimental campaign, a 154GHz gyrotron which had been conditioned to generate 1 MW/2 s, 0.5 MW/CW was installed for LHD experiments. Four high power gyrotrons (three-77 GHz/1~1.5 MW and one-154 GHz/1 MW) and a CW gyrotron (84 GHz/0.2 MW) are ready. Our experiment requires high energy and various injection patterns for Electron Cyclotron Resonance Heating (ECRH). Higher individual injection power and various injection patterns, we developed a power enhancement method by stepped anode acceleration voltage control and operated the gyrotron in the hard excitation region. These operations were realized by a remote controlled waveform generator. However the oscillation map of high power or long pulse operation in the hard excitation region were limited because in order to achieve the hard excitation region by the anode voltage control one must pass through the high anode current phase within a time short enough that the anode or the anode power supply is not overloaded. This limitation becomes more critical when the gyrotron beam current is increased in order to increase the output power. In the long pulse operation it was impossible to reach the hard excitation region in a low beam current (<10A).

  13. Anticipated and actual reactions to receiving HIV positive results through self-testing among gay and bisexual men.

    PubMed

    Martinez, Omar; Carballo-Diéguez, Alex; Ibitoye, Mobolaji; Frasca, Timothy; Brown, William; Balan, Iván

    2014-12-01

    We explored anticipated and actual reactions to receiving HIV positive results through self-testing with a diverse group of 84 gay and bisexual men in New York City. Grounded Theory was used to investigate these reactions in a two-phase study, one hypothetical, followed by a practical phase in which self-tests were distributed and used. Three major themes emerged when participants were asked about their anticipated reactions to an HIV positive self-test result: managing emotional distress, obtaining HIV medical care, and postponing sexual activity. When participants were asked about their anticipated reactions to a partner's HIV positive self-test result, five themes emerged: provide emotional support; refrain from engaging in sex with casual partner; avoid high-risk sexual activity with both main and casual partners; seek medical services; and obtain a confirmatory test result. Although none of the participants tested positive, seven of their partners did. Participants provided emotional support and linked their partners to support services. The availability of HIV self-testing kits offers potential opportunities to tackle HIV infection among individuals with high-risk practices. PMID:24858480

  14. Anticipated and Actual Reactions to Receiving HIV Positive Results Through Self-Testing Among Gay and Bisexual Men

    PubMed Central

    Carballo-Diéguez, Alex; Ibitoye, Mobolaji; Frasca, Timothy; Brown, William; Balan, Iván

    2014-01-01

    We explored anticipated and actual reactions to receiving HIV positive results through self-testing with a diverse group of 84 gay and bisexual men in New York City. Grounded Theory was used to investigate these reactions in a two-phase study, one hypothetical, followed by a practical phase in which self-tests were distributed and used. Three major themes emerged when participants were asked about their anticipated reactions to an HIV positive self-test result: managing emotional distress, obtaining HIV medical care, and postponing sexual activity. When participants were asked about their anticipated reactions to a partner’s HIV positive self-test result, five themes emerged: provide emotional support; refrain from engaging in sex with casual partner; avoid high-risk sexual activity with both main and casual partners; seek medical services; and obtain a confirmatory test result. Although none of the participants tested positive, seven of their partners did. Participants provided emotional support and linked their partners to support services. The availability of HIV self-testing kits offers potential opportunities to tackle HIV infection among individuals with high-risk practices. PMID:24858480

  15. Health monitoring of operational structures: Initial results

    NASA Astrophysics Data System (ADS)

    James, G.; Mayes, R.; Carne, T.; Simmermacher, T.; Goodding, J.

    Two techniques for damage localization (structural translational and rotational error checking - STRECH, and matrix completion - MAXCON) are described and applied to operational structures. The structures include a horizontal axis wind turbine (HAWT) blade undergoing a fatigue test and a highway bridge undergoing an induced damage test. STRECH is seen to provide a global damage indicator to assess the global damage state of a structure. STRECH is also seen to provide damage localization for static flexibility shapes or the first mode of simple structures. MAXCON is a robust damage localization tool using the higher order dynamics of a structure. Several options arc available to allow the procedure to be tailored to a variety of structures.

  16. Health monitoring of operational structures -- Initial results

    SciTech Connect

    James, G.; Mayes, R.; Carne, T.; Simmermacher, T.; Goodding, J.

    1995-03-01

    Two techniques for damage localization (Structural Translational and Rotational Error Checking -- STRECH and MAtriX COmpletioN -- MAXCON) are described and applied to operational structures. The structures include a Horizontal Axis Wind Turbine (HAWT) blade undergoing a fatigue test and a highway bridge undergoing an induced damage test. STRECH is seen to provide a global damage indicator to assess the global damage state of a structure. STRECH is also seen to provide damage localization for static flexibility shapes or the first mode of simple structures. MAXCON is a robust damage localization tool using the higher order dynamics of a structure. Several options arc available to allow the procedure to be tailored to a variety of structures.

  17. Safer production operations result from new technology

    SciTech Connect

    Wright, T.R. Jr.

    1982-07-01

    This article examines offshore innovations resulting from continued refinement and upgrading of earlier tools and methods, such as a subsurface safety valve with unique flapper design, a proposed platform design, an offshore traffic control system, below ocean-floor well completion, an anchor pile installation method, an underwater manifold center, and an articulated joint for gravity towers.

  18. Perceived Need and Actual Usage of the Family Support Agreement in Rural China: Results from a Nationally Representative Survey

    ERIC Educational Resources Information Center

    Chou, Rita Jing-Ann

    2011-01-01

    Purpose: The Family Support Agreement (FSA) is a voluntary but legal contract between older parents and adult children on parental support in China. As the first comprehensive empirical study on the FSA, this study aims to understand the prevalence and covariates of older parents' perceived need and actual use of this agreement. Design and…

  19. Two-D results on human operator perception

    NASA Technical Reports Server (NTRS)

    Siapkara, A. A.; Sheridan, T. B.

    1981-01-01

    The application of multidimensional scaling methodology in human factors engineering is presented. The nonorthogonality of internally perceived task variables is exhibited for first and second order plants with both dependent and independent task variables. Directions of operator preference are shown for actual performance, pilot opinion rating, and subjective measures of fatigue, adaptability, and system recognition. Improvement of performance in second order systems is exhibited by the use of bang-bang feedback information. Dissimilarity measures for system comparison are suggested in order to account for human operator rotations and subjective sense of time.

  20. Actual evapotranspiration (water use) assessment of the Colorado River Basin at the Landsat resolution using the operational simplified surface energy balance model

    USGS Publications Warehouse

    Singh, Ramesh K.; Senay, Gabriel B.; Velpuri, Naga Manohar; Bohms, Stefanie; Russell L, Scott; Verdin, James P.

    2014-01-01

    Accurately estimating consumptive water use in the Colorado River Basin (CRB) is important for assessing and managing limited water resources in the basin. Increasing water demand from various sectors may threaten long-term sustainability of the water supply in the arid southwestern United States. We have developed a first-ever basin-wide actual evapotranspiration (ETa) map of the CRB at the Landsat scale for water use assessment at the field level. We used the operational Simplified Surface Energy Balance (SSEBop) model for estimating ETa using 328 cloud-free Landsat images acquired during 2010. Our results show that cropland had the highest ETa among all land cover classes except for water. Validation using eddy covariance measured ETa showed that the SSEBop model nicely captured the variability in annual ETa with an overall R2 of 0.78 and a mean bias error of about 10%. Comparison with water balance-based ETa showed good agreement (R2 = 0.85) at the sub-basin level. Though there was good correlation (R2 = 0.79) between Moderate Resolution Imaging Spectroradiometer (MODIS)-based ETa (1 km spatial resolution) and Landsat-based ETa (30 m spatial resolution), the spatial distribution of MODIS-based ETa was not suitable for water use assessment at the field level. In contrast, Landsat-based ETa has good potential to be used at the field level for water management. With further validation using multiple years and sites, our methodology can be applied for regular production of ETa maps of larger areas such as the conterminous United States.

  1. Comparing results from actual and virtual linear scanlines in fractured sandstones of the Marnoso-Arenacea Formation, Northern Apennines, Italy

    NASA Astrophysics Data System (ADS)

    Borsani, Angelo; Balsamo, Fabrizio; Bistacchi, Andrea; Ogata, Kei; Storti, Fabrizio; Fetter, Marcos

    2016-04-01

    Three-dimensional photogrammetric techniques arecommonly used to generate high-resolution digital outcrop models suitable to complement stratigraphic and structural field studies. This is particularly true for near vertical outcrops were direct data collection is very difficult to perform, provided that the data are reliable. To check whether fracture attribute data acquired from photogrammetric digital outcrop models can be effectively integrate field data, we performed a multisource data acquisition programme on the master joint set affecting the Langhian part of the Marnoso Arenacea Formation, a foredeep siliciclastic turbidite succession widely exposed in the external sector of the Northern Apennines. We selected an about 90 m high vertical cliff in a meander of the Santerno River, which was surveyed by both terrestrial and drone-aided photogrammetry to produce two different digital outcrop models of the same strata. Moreover, field data were collected in the same strata along river bed exposures few hundred meters upstream. Comparison of master joint attributes, namely orientation, spacing and height, collected along linear scanlines in the field and in the two digital outcrop models shows quite comparable results, particularly when FSI (Fracture Spacing Index) values are considered. Sensitivity tests of the impact of the number of data on the statistical results from photogrammetric scanlines, where hundreds of measurements can be collected along each scan line, were also performed. Our results provide further support to the effectiveness of the integration between field and photogrammetrically-obtained structural data to study fracture densities in partially accessible exposures. Given the large data numbers that can be collected in digital outcrop models, once validated in the field, photogrammetric data allow robust statistical analysis to be performed on fracture attributes.

  2. Results of TMX operations: January-July 1980

    SciTech Connect

    Correll, D.L.; Drake, R.P.

    1980-09-25

    This interim report summarizes results from the Tandem Mirror Experiment (TMX) during the period January to July 1980 and describes the physics experiments, the machine operation, and the diagnostics that were added to TMX during this period. This operating period followed the initial proof-of-principle TMX experiments and predated the ongoing final experiments preceding TMX shutdown for modification to TMX Upgrade. The results described in this report include measurements of plasma parameters and plasma behavior which confirm the initial TMX results that demonstrated that the tandem mirror configuration can be generated and sustained by neutral beam injection and that the tandem mirror configuration improves confinement of magnetic mirror systems.

  3. SSPS results of test and operation, 1981-1984

    SciTech Connect

    1985-05-01

    The results of three years of testing and operation of the two dissimilar solar thermal power plants of the SSPS project are summarized. The project includes: (1) a Distributed Collector System, and (2) a Central Receiver System. Environmental conditions are presented and an economical assessment of the project is provided. (BCS)

  4. Preliminary operational results of the industrial process heat field tests

    SciTech Connect

    Kutscher, C.; Davenport, R.

    1980-04-01

    There are currently six DOE-funded solar industrial process heat (IPH) field tests which have been operational for one year or longer. These are all low temperature first generation projects which supply heat at temperatures below 100/sup 0/C - three hot water and three hot air. During the 1979 calendar year, personnel from the Solar Energy Research Institute (SERI) visited all of these sites; the performance and cost results obtained for each project and the operational problems encountered at each site are discussed.

  5. The Advanced Photon Source: Performance and results from early operation

    SciTech Connect

    Moncton, D.E.

    1997-10-01

    The Advanced Photon Source at Argonne National Laboratory is now providing researchers with extreme-brilliance undulator radiation in the hard x-ray region of the spectrum. All technical facilities and components are operational and have met design specifications. Fourteen research teams, occupying 20 sectors on the APS experiment hall floor, are currently installing beamline instrumentation or actively taking data. An overview is presented for the first operational years of the Advanced Photon Source. Emphasis is on the performance of accelerators and insertion devices, as well as early scientific results and future plans.

  6. Operating results confirm high efficiency of continuous rolling

    SciTech Connect

    Masselot, J.M.; Pradayrol, G.; Boughton, J.R.

    1995-09-01

    Started up in the middle of 1986, Sollac Sainte-Agathe`s coupled pickle line and cold rolling mill has overtaken the original capacity and quality targets. The results and how they were achieved will be presented. Attention is directed to the features of the key sections which include: pickel line entry; process (scale breaker/tension leveler, pickling tank, rinse tanks); side trimming; mill entry; rolling; and mill exit. The performance reached is the result of optimized global design and involvement of operational staff in an adapted organization. On the basis of the results already obtained, new objectives and the means for achieving them are presented.

  7. Cluster operations in support of SWARM and first results

    NASA Astrophysics Data System (ADS)

    Masson, Arnaud; Escoubet, Philippe; Laakso, Harri

    2015-04-01

    The measure of the Earth's magnetic field is perturbed by the external electric currents flowing in the magnetosphere and the ionosphere. One of the SWARM prime scientific objectives is to investigate the influence of these currents, including the ring current and field aligned currents (FAC). To help disentangle their effects, special operations have been designed and coordinated with the ESA Cluster mission. This unique constellation of four satellites enable the measure of these currents at higher altitudes better than any previous mission. The complementarity of these two missions was foreseen at the beginning of the SWARM mission design, about 10 years ago. The 2014 special operations in support of SWARM is in other words a forward-looking idea becoming reality. We will first briefly recall a few scientific highlights of the Cluster mission, related to the first measure of currents in space by a constellation of four satellites. We will then talk about the 2014 special operations designed and executed in support of SWARM. We will then present future special operations that are planned to be executed by Cluster up to 2018 in support of SWARM. Preliminary results already obtained will be also evoked.

  8. [Results of operator's work during space flight (experiment "pilot") under different work-and-rest cycles].

    PubMed

    Sal'nitskiĭ, V P; Dudukin, A V; Savchenko, É G; Stepanova, S I; Nesterov, V F; Saraev, I F

    2012-01-01

    The correlation between operator's job quality and crew work-rest cycle (WRC) aboard the International space station was studied. The experiment involved 10 Russian members of ISS missions 17-24 at the age of 35 to 51 yrs. Mission duration varied from 163 to 200 days, averaging 180 days. Each cosmonaut carried out several "pilot" test sessions. The number of sessions per mission ranged from 4 to 6. The procedure consisted of simulating manual operation of transport vehicle Soyuz on the stages of hang-up, berthing and docking with the ISS. Objective job quality parameters were accuracy of the Soyuz and ISS relative motion control and time for completion which actually characterized work rate. WRC intensity was judged by the data of monitoring at the Moscow Mission Control Center. The results lend support to the dependence of operator's efficiency on WRC. In operators aimed at the highest accuracy this dependence manifested itself in work rate parameters; work accuracy but not rate was more WRC-dependent in operators aimed at doing their job fast. In other words, WRC intensity impacted mostly those job qualities that operator considered to be of secondary importance. PMID:23402140

  9. Bacteremia during dacryocystorhinostomy: results of intra-operative blood cultures

    PubMed Central

    2014-01-01

    Background The aims of the study are to assess the prevalence of bacteremia during dacryocystorhinostomy (DCR) and to assess whether there is a need for post-operative prophylaxis. Prospective interventional study of 52 consecutive dacryocystorhinostomy performed in 50 patients over a period of 1 year from 2013 to 2014. Blood was drawn under strict aseptic conditions during two separate time points: fashioning of the nasal mucosal and creation of lacrimal sac flaps. The blood was inoculated into two blood culture bottles: the dual media as well as Columbia broth. Following withdrawal of blood, all patients received an intraoperative single dose of a cephalosporin antibiotic. Clean cases of primary acquired nasolacrimal duct obstructions (PANDO) without any sac discharge upon marsupialization (22%, 11/50) were not prescribed routine post-operative prophylaxis, whereas the remaining were prescribed oral antibiotics for 5 days. Results The mean age of patients was 41 years (range, 4–61 years). The most common diagnosis (70%, 35/50) was primary acquired nasolacrimal duct obstruction. Acute dacryocystitis was noted in 12% (6/50). External DCR was performed in 65% (34/52) and endoscopic DCR in 35% (18/52) of the cases. All the blood cultures were uniformly negative both in terms of abnormal physical changes in media as well subcultures; 22% (11/50) did not receive post-operative antibiotic prophylaxis. None of the patients developed any signs of wound infections. The anatomical and functional success rate was achieved in 98%. Conclusions This study did not find any intraoperative bacteremia during dacryocystorhinostomy and that none had wound infection irrespective of post-operative prophylaxis. PMID:25320650

  10. High Temperature Electrolysis Pressurized Experiment Design, Operation, and Results

    SciTech Connect

    J.E. O'Brien; X. Zhang; G.K. Housley; K. DeWall; L. Moore-McAteer

    2012-09-01

    A new facility has been developed at the Idaho National Laboratory for pressurized testing of solid oxide electrolysis stacks. Pressurized operation is envisioned for large-scale hydrogen production plants, yielding higher overall efficiencies when the hydrogen product is to be delivered at elevated pressure for tank storage or pipelines. Pressurized operation also supports higher mass flow rates of the process gases with smaller components. The test stand can accommodate planar cells with dimensions up to 8.5 cm x 8.5 cm and stacks of up to 25 cells. It is also suitable for testing other cell and stack geometries including tubular cells. The pressure boundary for these tests is a water-cooled spool-piece pressure vessel designed for operation up to 5 MPa. Pressurized operation of a ten-cell internally manifolded solid oxide electrolysis stack has been successfully demonstrated up 1.5 MPa. The stack is internally manifolded and operates in cross-flow with an inverted-U flow pattern. Feed-throughs for gas inlets/outlets, power, and instrumentation are all located in the bottom flange. The entire spool piece, with the exception of the bottom flange, can be lifted to allow access to the internal furnace and test fixture. Lifting is accomplished with a motorized threaded drive mechanism attached to a rigid structural frame. Stack mechanical compression is accomplished using springs that are located inside of the pressure boundary, but outside of the hot zone. Initial stack heatup and performance characterization occurs at ambient pressure followed by lowering and sealing of the pressure vessel and subsequent pressurization. Pressure equalization between the anode and cathode sides of the cells and the stack surroundings is ensured by combining all of the process gases downstream of the stack. Steady pressure is maintained by means of a backpressure regulator and a digital pressure controller. A full description of the pressurized test apparatus is provided in this

  11. Evaluation of stereoscopic video cameras synchronized with the movement of an operator's head on the teleoperation of the actual backhoe shovel

    NASA Astrophysics Data System (ADS)

    Minamoto, Masahiko; Matsunaga, Katsuya

    1999-05-01

    Operator performance while using a remote controlled backhoe shovel is described for three different stereoscopic viewing conditions: direct view, fixed stereoscopic cameras connected to a helmet mounted display (HMD), and rotating stereo camera connected and slaved to the head orientation of a free moving stereo HMD. Results showed that the head- slaved system provided the best performance.

  12. Operational Results From a High Power Alternator Test Bed

    NASA Technical Reports Server (NTRS)

    Birchenough, Arthur; Hervol, David

    2007-01-01

    The Alternator Test Unit (ATU) in the Lunar Power System Facility (LPSF) located at the NASA Glenn Research Center (GRC) in Cleveland, Ohio was used to simulate the operating conditions and evaluate the performance of the ATU and its interaction with various LPSF components in accordance with the current Fission Surface Power System (FSPS) requirements. The testing was carried out at the breadboard development level. These results successfully demonstrated excellent ATU power bus characteristics and rectified user load power quality during steady state and transient conditions. Information gained from this work could be used to assist the design and primary power quality considerations for a possible future FSPS. This paper describes the LPSF components and some preliminary test results.

  13. Operational Results of a Closed Brayton Cycle Test-Loop

    NASA Astrophysics Data System (ADS)

    Wright, Steven A.; Fuller, Robert; Lipinski, Ronald J.; Nichols, Kenneth; Brown, Nicholas

    2005-02-01

    A number of space and terrestrial power system designs plan to use nuclear reactors that are coupled to Closed-loop Brayton Cycle (CBC) systems to generate electrical power. Because very little experience exists regarding the operational behavior of these systems, Sandia National Laboratories (through its Laboratory Directed Research and Development program) is developing a closed-loop test bed that can be used to determine the operational behavior of these systems and to validate models for these systems. Sandia has contracted Barber-Nichols Corporation to design, fabricate, and assemble a Closed-loop Brayton Cycle (CBC) system. This system was developed by modifying commercially available hardware. It uses a 30 kWe Capstone C-30 gas-turbine unit (www.capstoneturbine.com) with a modified housing that permits the attachment of an electrical heater and a water cooled chiller that are connected to the turbo-machinery in a closed loop. The test-loop reuses the Capstone turbine, compressor, and alternator. The Capstone system's nominal operating point is 1150 K turbine inlet temperature at 96,000 rpm. The annular recuperator and portions of the Capstone control system (inverter) and starter system are also reused. The rotational speed of the turbo-machinery is controlled either by adjusting the alternator load by either using the electrical grid or a separate load bank. This report describes the test-loop hardware SBL-30 (Sandia Brayton Loop-30kWe). Also presented are results of early testing and modeling of the unit. The SBL-30 hardware is currently configured with a heater that is limited to 80 kWth with a maximum outlet temperature of ˜1000 K.

  14. Operational results of a Closed Brayton Cycle test-loop.

    SciTech Connect

    Fuller, Robert; Wright, Steven Alan; Nichols, Kenneth Graham.; Brown, Nicholas; Lipinski, Ronald J.

    2004-11-01

    A number of space and terrestrial power system designs plan to use nuclear reactors that are coupled to Closed-loop Brayton Cycle (CBC) systems to generate electrical power. Because very little experience exists regarding the operational behavior of these systems, Sandia National Laboratories (through its Laboratory Directed Research and Development program) is developing a closed-loop test bed that can be used to determine the operational behavior of these systems and to validate models for these systems. Sandia has contracted Barber-Nichols Corporation to design, fabricate, and assemble a Closed-loop Brayton Cycle (CBC) system. This system was developed by modifying commercially available hardware. It uses a 30 kWe Capstone C-30 gas-turbine unit (www.capstoneturbine.com) with a modified housing that permits the attachment of an electrical heater and a water cooled chiller that are connected to the turbo-machinery in a closed loop. The test-loop reuses the Capstone turbine, compressor, and alternator. The Capstone system's nominal operating point is 1150 K turbine inlet temperature at 96,000 rpm. The annular recuperator and portions of the Capstone control system (inverter) and starter system are also reused. The rotational speed of the turbo-machinery is controlled either by adjusting the alternator load by either using the electrical grid or a separate load bank. This report describes the test-loop hardware SBL-30 (Sandia Brayton Loop-30kWe). Also presented are results of early testing and modeling of the unit. The SBL-30 hardware is currently configured with a heater that is limited to 80 kW{sub th} with a maximum outlet temperature of {approx}1000 K.

  15. TASAR Certification and Operational Approval Requirements - Analyses and Results

    NASA Technical Reports Server (NTRS)

    Koczo, Stefan, Jr.

    2015-01-01

    This report documents the results of research and development work performed by Rockwell Collins in addressing the Task 1 objectives under NASA Contract NNL12AA11C. Under this contract Rockwell Collins provided analytical support to the NASA Langley Research Center (LaRC) in NASA's development of a Traffic Aware Strategic Aircrew Requests (TASAR) flight deck Electronic Flight Bag (EFB) application for technology transition into operational use. The two primary objectives of this contract were for Rockwell Collins and the University of Iowa OPL to 1) perform an implementation assessment of TASAR toward early certification and operational approval of TASAR as an EFB application (Task 1 of this contract), and 2) design, develop and conduct two Human-in-the-Loop (HITL) simulation experiments that evaluate TASAR and the associated Traffic Aware Planner (TAP) software application to determine the situational awareness and workload impacts of TASAR in the flight deck, while also assessing the level of comprehension, usefulness, and usability of the features of TAP (Task 2 of this contract). This report represents the Task 1 summary report. The Task 2 summary report is provided in [0].

  16. Ground Operations Demonstration Unit for Liquid Hydrogen Initial Test Results

    NASA Technical Reports Server (NTRS)

    Notardonato, W. U.; Johnson, W. L.; Swanger, A. M.; Tomsik, T.

    2015-01-01

    NASA operations for handling cryogens in ground support equipment have not changed substantially in 50 years, despite major technology advances in the field of cryogenics. NASA loses approximately 50% of the hydrogen purchased because of a continuous heat leak into ground and flight vessels, transient chill down of warm cryogenic equipment, liquid bleeds, and vent losses. NASA Kennedy Space Center (KSC) needs to develop energy-efficient cryogenic ground systems to minimize propellant losses, simplify operations, and reduce cost associated with hydrogen usage. The GODU LH2 project has designed, assembled, and started testing of a prototype storage and distribution system for liquid hydrogen that represents an advanced end-to-end cryogenic propellant system for a ground launch complex. The project has multiple objectives including zero loss storage and transfer, liquefaction of gaseous hydrogen, and densification of liquid hydrogen. The system is unique because it uses an integrated refrigeration and storage system (IRAS) to control the state of the fluid. This paper will present and discuss the results of the initial phase of testing of the GODU LH2 system.

  17. Ground operations demonstration unit for liquid hydrogen initial test results

    NASA Astrophysics Data System (ADS)

    Notardonato, W. U.; Johnson, W. L.; Swanger, A. M.; Tomsik, T.

    2015-12-01

    NASA operations for handling cryogens in ground support equipment have not changed substantially in 50 years, despite major technology advances in the field of cryogenics. NASA loses approximately 50% of the hydrogen purchased because of a continuous heat leak into ground and flight vessels, transient chill down of warm cryogenic equipment, liquid bleeds, and vent losses. NASA Kennedy Space Center (KSC) needs to develop energy-efficient cryogenic ground systems to minimize propellant losses, simplify operations, and reduce cost associated with hydrogen usage. The GODU LH2 project has designed, assembled, and started testing of a prototype storage and distribution system for liquid hydrogen that represents an advanced end-to-end cryogenic propellant system for a ground launch complex. The project has multiple objectives including zero loss storage and transfer, liquefaction of gaseous hydrogen, and densification of liquid hydrogen. The system is unique because it uses an integrated refrigeration and storage system (IRAS) to control the state of the fluid. This paper will present and discuss the results of the initial phase of testing of the GODU LH2 system.

  18. Results of DIII-D operation with new enabling technologies

    SciTech Connect

    Simonen, T.C.

    1997-03-01

    Recent experiments on DIII-D have been carried out to understand and explore optimized tokamak operating modes by exploiting control of the plasma current and pressure profiles using new RF current drive and divertor technology. DIII-D emphasizes plasma shape and divertor experiments using a digital plasma control system and extensive diagnostics to develop improved understanding and control of transport barriers in high performance plasmas. The emphasis of the program is to extend the duration of high performance operating modes beyond the plasma current relaxation time by using ICRF and ECH current drive. Engineering features of the new RF systems being developed for these experiments as well as new divertor results are described. DIII-D employs multi-element ICRF antennas for fast-wave electron heating and on-axis current drive and is beginning 110 GHz ECH experiments with MW-level gyrotrons for off-axis current drive. DIII-D employs active cryogenic divertor neutral particle pumping for plasma density and plasma pressure profile control. A divertor modification is now being implemented on DIII-D to pump higher triangularity plasmas and to better baffle neutral backflow from the recycling divertor region.

  19. Weather Forecasting for Ka-band Operations: Initial Study Results

    NASA Astrophysics Data System (ADS)

    Morabito, D.; Wu, L.; Slobin, S.

    2016-08-01

    As lower frequency bands (e.g., 2.3 GHz and 8.4 GHz) have become oversubscribed during the past several decades, NASA has become interested in using higher frequency bands (e.g., 26 GHz and 32 GHz) for telemetry, thus making use of the available wider bandwidth. However, these bands are more susceptible to atmospheric degradation. Currently, flight projects tend to be conservative in preparing their communications links by using worst-case or conservative assumptions. Such assumptions result in nonoptimum data return. We explore the use of weather forecasting for Goldstone and Madrid for different weather condition scenarios to determine more optimal values of atmospheric attenuation and atmospheric noise temperature for use in telecommunication link design. We find that the use of weather forecasting can provide up to 2 dB or more of increased data return when more favorable conditions are forecast. Future plans involve further developing the technique for operational scenarios with interested flight projects.

  20. FOUR YEARS OF OPERATIONS AND RESULTS WITH FORTE

    SciTech Connect

    D. ROUSSEL-DUPRE; P. KLINGNER; L. CARLSON; ET AL

    2001-06-01

    The FORTE (Fast Onboard Recording of Transient Events) satellite was launched on 29 August 1997 and has been in continuous operation since that time. FORTE was placed in a nearly circular, 825-km-altitude, 70 degrees inclination orbit by a Pegasus rocket funded by Air Force Space Test Program. The Department of Energy funded the FORTE satellite, which was designed and built at Los Alamos. FORTE's successful launch and engineered robustness were a result of several years of dedicated work by the joint Los Alamos National Laboratory/Sandia National Laboratory project team, led through mission definition, payload and satellite development, and launch by Dr. Stephen Knox. The project is now led by Dr. Abram Jacobson. FORTE carries a suite of instruments, an optical system and a rf system, for the study of lightning and anthropogenic signals. As a result of this effort, new understandings of lightning events have emerged as well as a more complete understanding of the relationship between optical and rf lightning events. This paper will provide an overview of the FORTE satellite and will discuss the on orbit performance of the subsystems.

  1. Four years of operations and results with FORTE

    SciTech Connect

    Klingner, P. L.; Carlson, L. D.; Dingler, R. D.; Esch-Mosher, D. M.; Jacobson, A. R.; Roussel-Dupre, D.

    2001-01-01

    The FORTE (Fast Onboard Recording of Transient Events) satellite was launched on 29 August 1997 and has been in continuous operation since that time. FORTE was placed in a nearly circular, 825-km-altitude, 70 degrees inclination orbit by a Pegasus rocket funded by Air Force Space Test Program. The Department of Energy funded the FORTE satellite, which was designed and built at Los Alamos. FORTE's successful launch and engineered robustness were a result of several years of dedicated work by the joint Los Alamos National Laboratory/Sandia National Laboratory project team, led through mission definition, payload and satellite development, and launch by Dr. Stephen Knox. The project is now led by Dr. Abram Jacobson. FORTE carries a suite of instruments, an optical system and a rf system, for the study of lightning and anthropogenic signals. As a result of this effort, new understandings of lightning events have emerged as well as a more complete understanding of the relationship between optical and rf lightning events. This paper will provide an overview of the FORTE satellite and will discuss the on orbit performance of the subsystems.

  2. Canister Decontamination Chamber No. 1 operability test results

    SciTech Connect

    Magoulas, V.E.

    1987-10-30

    The DWPF Canister Decontamination Chamber No. 1 (CDC) was installed at the TNX facility in October, 1986 for operability testing. Operability testing was required because this equipment is unique and is a critical part of the defense waste process. The test was successful in demonstrating the canister decontamination operation. Testing verified proper nozzle locations, frit suspension, level probe and CCTV operations. The following recommendations are based on data obtained from frit blasting 24 canisters: reduce the recirculation pump speed, to allow proper level probes operation; add an extension to the chamber rinse nozzle which allows removal of frit from the top of the upper guide rinse nozzle; increase visibility through the CCTV camera; make the CMM grapple jaw pins more compatible with the MSM; and improve canister guide capability to aid in canister loading. CDC Operability Testing was completed October, 1987. 6 refs., 11 figs., 2 tabs.

  3. Development and Preliminary Results of CTAS on Airline Operational Control Center Operations

    NASA Technical Reports Server (NTRS)

    Zelenka, Richard; Beatty, Roger; Engelland, Shawn

    2004-01-01

    Continued growth and expansion of air traffic and increased air carrier economic pressures have mandated greater flexibility and collaboration in air traffic management. The ability of airspace users to select their own routes, so called "free-flight", and to more actively manage their fleet operations for maximum economic advantage are receiving great attention. A first step toward greater airspace user and service provider collaboration is information sharing. In this work, arrival scheduling and airspace management data generated by the NASA/FAA Center/TRACON Automation System (CTAS) and used by the FAA service provider is shared with an airline with extensive operations within the CTAS operational domain. The design and development of a specialized airline CTAS "repeater" system is described, as well as some preliminary results of the impact and benefits of this information on the air carrier's operations. FAA controller per aircraft scheduling information, such as that provided by CTAS, has never before been shared in real-time with an airline. Expected airline benefits include improved fleet planning and arrival gate management, more informed "hold-go decisions, and avoidance of costly aircraft diversions to alternate airports when faced with uncertain airborne arrival delays.

  4. Development and Preliminary Results of CTAS on Airline Operational Control Center Operations

    NASA Technical Reports Server (NTRS)

    Zelenka, Richard; Beatty, Roger; Falcone, Richard; Engelland, Shawn; Tobias, Leonard (Technical Monitor)

    1998-01-01

    Continued growth and expansion of air traffic and increased air carrier economic pressures have mandated greater flexibility and collaboration in air traffic management. The ability of airspace users to select their own routes, so called "free-flight", and to more actively manage their fleet operations for maximum economic advantage are receiving great attention. A first step toward greater airspace user and service provider collaboration is information sharing. In this work, arrival scheduling and airspace management data generated by the NASA/FAA Center/TRACON Automation System (CTAS) and used by the FAA service provider is shared with an airline with extensive operations within the CTAS operational domain. The design and development of a specialized airline CTAS "repeater" system is described, as well as some preliminary results of the impact and benefits of this information on the air carrier's operations. FAA controller per aircraft scheduling information, such as that provided by CTAS, has never before been shared in real-time with an airline. Expected airline benefits include improved fleet planning and arrival gate management, more informed "hold-go" decisions, and avoidance of costly aircraft diversions to alternate airports when faced with uncertain airborne arrival delays.

  5. The ESA Scientific Exploitation of Operational Missions element, first results

    NASA Astrophysics Data System (ADS)

    Desnos, Yves-Louis; Regner, Peter; Delwart, Steven; Benveniste, Jerome; Engdahl, Marcus; Mathieu, Pierre-Philippe; Gascon, Ferran; Donlon, Craig; Davidson, Malcolm; Pinnock, Simon; Foumelis, Michael; Ramoino, Fabrizio

    2016-04-01

    SEOM is a program element within the fourth period (2013-2017) of ESA's Earth Observation Envelope Programme (http://seom.esa.int/). The prime objective is to federate, support and expand the international research community that the ERS, ENVISAT and the Envelope programmes have built up over the last 25 years. It aims to further strengthen the leadership of the European Earth Observation research community by enabling them to extensively exploit future European operational EO missions. SEOM will enable the science community to address new scientific research that are opened by free and open access to data from operational EO missions. Based on community-wide recommendations for actions on key research issues, gathered through a series of international thematic workshops and scientific user consultation meetings, a work plan is established and is approved every year by ESA Members States. During 2015 SEOM, Science users consultation workshops have been organized for Sentinel1/3/5P ( Fringe, S3 Symposium and Atmospheric science respectively) , new R&D studies for scientific exploitation of the Sentinels have been launched ( S3 for Science SAR Altimetry and Ocean Color , S2 for Science,) , open-source multi-mission scientific toolboxes have been launched (in particular the SNAP/S1-2-3 Toolbox). In addition two advanced international training courses have been organized in Europe to exploit the new S1-A and S2-A data for Land and Ocean remote sensing (over 120 participants from 25 countries) as well as activities for promoting the first scientific results ( e.g. Chili Earthquake) . In addition the First EO Open Science 2.0 was organised at ESA in October 2015 with 225 participants from 31 countries bringing together young EO scientists and data scientists. During the conference precursor activities in EO Open Science and Innovation were presented, while developing a Roadmap preparing for future ESA scientific exploitation activities. Within the conference, the first

  6. Initial results from the unipolar operation of the RHEPP module

    SciTech Connect

    Harjes, H.C.; Penn, K.J.; Reed, K.W.; McClenahan, C.R.; Laderach, G.E.; Wavrik, R.W.; Adcock, J.L.; Butler, M.E.; Mann, G.A.; Pena, G.E.; Weber, G.J.; VanDeValde, D.; Martinez, L.E.; Muirhead, D.; Kiekel, P.D.; Johnson, D.L.; Neau, E.L.

    1992-08-01

    Several potential applications such as medical waste treatment, chemical waste treatment, food treatment, and flue gas cleanup have been identified for high average power electron beam systems. The technology for such a system is being developed in the RHEPP (Repetitive High Energy Pulsed Power) project. The RHEPP module consists of a multistage magnetic pulse compressor driving a linear induction voltage adder with an e-beam diode load. It has been designed to operate continuously, delivering 350 kW of average power to the diode in 60-ns FWHM, 2.5-MV, 2.9-kJ pulses. The module is presently under construction with the first phase scheduled for completion in the summer of 1992. In the first phase, four of ten adder stages are being built so that testing can begin with a I-MV, 160-kW diode with the balance of the power from the compressor diverted to a resistive load. A description of the system and test results from the initial stages of the compressor will be presented.

  7. Initial results from the unipolar operation of the RHEPP module

    SciTech Connect

    Harjes, H.C.; Penn, K.J.; Reed, K.W.; McClenahan, C.R.; Laderach, G.E.; Wavrik, R.W.; Adcock, J.L.; Butler, M.E.; Mann, G.A.; Pena, G.E.; Weber, G.J.; VanDeValde, D.; Martinez, L.E.; Muirhead, D.; Kiekel, P.D.; Johnson, D.L.; Neau, E.L.

    1992-01-01

    Several potential applications such as medical waste treatment, chemical waste treatment, food treatment, and flue gas cleanup have been identified for high average power electron beam systems. The technology for such a system is being developed in the RHEPP (Repetitive High Energy Pulsed Power) project. The RHEPP module consists of a multistage magnetic pulse compressor driving a linear induction voltage adder with an e-beam diode load. It has been designed to operate continuously, delivering 350 kW of average power to the diode in 60-ns FWHM, 2.5-MV, 2.9-kJ pulses. The module is presently under construction with the first phase scheduled for completion in the summer of 1992. In the first phase, four of ten adder stages are being built so that testing can begin with a I-MV, 160-kW diode with the balance of the power from the compressor diverted to a resistive load. A description of the system and test results from the initial stages of the compressor will be presented.

  8. Enhanced vision systems: results of simulation and operational tests

    NASA Astrophysics Data System (ADS)

    Hecker, Peter; Doehler, Hans-Ullrich

    1998-07-01

    Today's aircrews have to handle more and more complex situations. Most critical tasks in the field of civil aviation are landing approaches and taxiing. Especially under bad weather conditions the crew has to handle a tremendous workload. Therefore DLR's Institute of Flight Guidance has developed a concept for an enhanced vision system (EVS), which increases performance and safety of the aircrew and provides comprehensive situational awareness. In previous contributions some elements of this concept have been presented, i.e. the 'Simulation of Imaging Radar for Obstacle Detection and Enhanced Vision' by Doehler and Bollmeyer 1996. Now the presented paper gives an overview about the DLR's enhanced vision concept and research approach, which consists of two main components: simulation and experimental evaluation. In a first step the simulational environment for enhanced vision research with a pilot-in-the-loop is introduced. An existing fixed base flight simulator is supplemented by real-time simulations of imaging sensors, i.e. imaging radar and infrared. By applying methods of data fusion an enhanced vision display is generated combining different levels of information, such as terrain model data, processed images acquired by sensors, aircraft state vectors and data transmitted via datalink. The second part of this contribution presents some experimental results. In cooperation with Daimler Benz Aerospace Sensorsystems Ulm, a test van and a test aircraft were equipped with a prototype of an imaging millimeter wave radar. This sophisticated HiVision Radar is up to now one of the most promising sensors for all weather operations. Images acquired by this sensor are shown as well as results of data fusion processes based on digital terrain models. The contribution is concluded by a short video presentation.

  9. Results of instrumental and operative implementation of T-Flap

    NASA Astrophysics Data System (ADS)

    Marcelli, M.; Madonia, A.; Piermattei, V.; Mainardi, U.

    2012-04-01

    The development of new technologies for the study of the ocean processes is one of the most innovative aspects of oceanographic research that increasingly requires a large amount of data for an integrated approach to in situ observations, forecasting models and remotely sensed data. At now the marine measurement technologies are too expensive for an extensive utilization. The T-Flap technology (Temperature-Fluorescence LAunchable Probe) meets these needs by providing low cost and user-friendly in situ measuring of physical and bio-optical variables of water bodies, as opposed to traditional methods. Many experimental laboratory tests were carried out in order to increase the instrumental sensitivity of the fluorimetric sensor for the detection of chlorophyll a concentration. To test the selected components (LEDs, diodes, filters) and their new configurations, an optical circuit has been realized consisting on three prototypes of the measuring cell. Fluorescence excitation and detection efficiency of the new electro-optical assemblages were also tested by the comparison between the voltage output signals and spectroscopic in vivo fluorescence measures both of natural seawater samples and marine cultures at different concentrations. The upgraded sensors were tested during different oceanographic surveys performed in the last years both in the Tyrrhenian Sea and Adriatic Sea. The technological achievements were applied in different operative conditions: profiler along the water column (not expendable) and stand alone (in continuous surface acquisitions along tracks, in continuous acquisition on a buoy). In this work we present the results of the latest research activities on T-Flap evolution. In addition preliminary results about new sensors currently under development are shown, such as CDOM (Cromophoric Dissolved Organic Matter) fluorimetric sensor, based on T-Flap fluorescence technology, and conductivity sensor.

  10. A good morale: The key to outstanding operation results

    SciTech Connect

    Knaisch, O.

    1996-10-01

    The key elements responsible for the success of Alouette, a greenfield aluminum smelter operating in northern Quebec, Canada, are based on the use of adaptive human resources techniques in conjunction with state-of-the-art technology and technical expertise. In effect, an open style of management has led to the development of a progressive attitude among employees.

  11. Operational results of pilot cell test with cermet inert'' anodes

    SciTech Connect

    Alcorn, T.R.; Tabereaux, A.T.; Richards, N.E. . Mfg. Technology Lab.); Windisch, C.F. Jr.; Strachan, D.M. ); Gregg, J.S.; Frederick, M.S. )

    1993-02-01

    The operational performance of a six-pack'' of cermet anodes and corrosion rates was evaluated in a six kA pilot reduction cell at Reynolds' Manufacturing Technology Laboratory. Two separate test periodswere conducted with the cermet anodes; the first period was in conjunction with the Pacific Northwest Laboratory and the second with ELTECH Research Corporation. Both tests used identical NiO-NiFe[sub 2]O[sub 4]-Cu anodes manufactured by Ceramic Magnetics, Inc.. The ELTECH testing involved the in situ coating of the anodes with cerium oxide. Primary evaluations for both test periods were conducted at target conditions of alumina saturation and 0.5 amp/cm[sup 2] anode current density. Individual anodes remained in operation for 25 days during the two and one-half month testing period. Operational difficulties developed throughout the test due to breakage of the anode conductor stems, cracking and breaking of the cermet anodes, unequal anode current distribution, and alumina muck build-up in the cell. These operational problems are discussed as well as an estimate of anode corrosion rates based on metal impurity levels in the aluminum metal pad.

  12. Operational results of pilot cell test with cermet ``inert`` anodes

    SciTech Connect

    Alcorn, T.R.; Tabereaux, A.T.; Richards, N.E.; Windisch, C.F. Jr.; Strachan, D.M.; Gregg, J.S.; Frederick, M.S.

    1993-02-01

    The operational performance of a ``six-pack`` of cermet anodes and corrosion rates was evaluated in a six kA pilot reduction cell at Reynolds` Manufacturing Technology Laboratory. Two separate test periodswere conducted with the cermet anodes; the first period was in conjunction with the Pacific Northwest Laboratory and the second with ELTECH Research Corporation. Both tests used identical NiO-NiFe{sub 2}O{sub 4}-Cu anodes manufactured by Ceramic Magnetics, Inc.. The ELTECH testing involved the in situ coating of the anodes with cerium oxide. Primary evaluations for both test periods were conducted at target conditions of alumina saturation and 0.5 amp/cm{sup 2} anode current density. Individual anodes remained in operation for 25 days during the two and one-half month testing period. Operational difficulties developed throughout the test due to breakage of the anode conductor stems, cracking and breaking of the cermet anodes, unequal anode current distribution, and alumina muck build-up in the cell. These operational problems are discussed as well as an estimate of anode corrosion rates based on metal impurity levels in the aluminum metal pad.

  13. Multi-Center Traffic Management Advisor Operational Field Test Results

    NASA Technical Reports Server (NTRS)

    Farley, Todd; Landry, Steven J.; Hoang, Ty; Nickelson, Monicarol; Levin, Kerry M.; Rowe, Dennis W.

    2005-01-01

    The Multi-Center Traffic Management Advisor (McTMA) is a research prototype system which seeks to bring time-based metering into the mainstream of air traffic control (ATC) operations. Time-based metering is an efficient alternative to traditional air traffic management techniques such as distance-based spacing (miles-in-trail spacing) and managed arrival reservoirs (airborne holding). While time-based metering has demonstrated significant benefit in terms of arrival throughput and arrival delay, its use to date has been limited to arrival operations at just nine airports nationally. Wide-scale adoption of time-based metering has been hampered, in part, by the limited scalability of metering automation. In order to realize the full spectrum of efficiency benefits possible with time-based metering, a much more modular, scalable time-based metering capability is required. With its distributed metering architecture, multi-center TMA offers such a capability.

  14. CAISI Operational Assessment (OA) data collection results. Final report

    SciTech Connect

    1997-01-31

    One of the lessons learned from Operation Desert Shield/Storm was the inability of deployed Combat Service Support (CSS) computers to exchange data effectively in a battlefield environment. The work-around solution to this previously identified problem has been to physically carry floppy disks between computers. A General Officer Steering Committee, directed by the Vice Chief of Staff of the Army, determined that immediate corrective action was necessary to ensure viability of the CSS Battlefield Mission Area. The study recommended that a three-phased system development plan address short-, mid- and long-term CSS automation communication interface requirements. In response to this study, Program Executive Office (PEO) Standard Army Management Information System (STAMIS) authorized the development of the CSS Automated Information System Interface (CAISI). Phase I (Near-Term) equipped the {open_quotes}first to fight{close_quotes} Contingency Corps units. Phase II (Mid-Term) is being fielded to the remainder of Force Package One units in the active force. Phase III (Long-Term) will equip the remaining units. CAISI is now in the early stages of Phase II fielding. Prior to full Phase II fielding, CAISI must be approved for production by a Milestone III decision authority. Part of the data that will be used in the Milestone III decision is a demonstration of the CAISI`s operational suitability, as assessed by the US Army Operational Test and Evaluation Command (OPTEC). This assessment will be performed through an Operational Assessment (OA) using data provided from previous technical testing, such as the CAISI Customer User Test (CUT), and a field training exercise conducted by units of the XVIII Airborne Corps. The field training exercise data collection took place during two events.

  15. Preliminary operational results from the Willard solar power system

    NASA Technical Reports Server (NTRS)

    Fenton, D. L.; Abernathy, G. H.; Krivokapich, G.; Ellibee, D. E.; Chilton, V.

    1980-01-01

    The solar powered system located near Willard, New Mexico, generates mechanical or electrical power at a capacity of 19 kW (25 HP). The solar collection system incorporates east/west tracking parabolic trough collectors with a total aperture area of 1275 sq m (13,720 sq ft). The hot oil type thermal energy storage is sufficient for approximately 20 hours of power system operation. The system utilizes a reaction type turbine in conjunction with an organic Rankine cycle engine. Total collector field efficiency reaches a maximum of 20 percent near the winter solstice and about 50 percent during the summer. During the month of July, 1979, the system pumped 60 percent of the 35,300 cu m (28.6 acre-feet) of water delivered. Operating efficiencies for the turbine component, organic Rankine cycle engine and the complete power system are respectively 65 to 75 percent, 12 to 15 percent and 5 to 6 percent. Significant maintenance time was expended on both the collector and power systems throughout the operational period.

  16. Preliminary operational results from the Willard solar power system

    NASA Astrophysics Data System (ADS)

    Fenton, D. L.; Abernathy, G. H.; Krivokapich, G.; Ellibee, D. E.; Chilton, V.

    1980-05-01

    The solar powered system located near Willard, New Mexico, generates mechanical or electrical power at a capacity of 19 kW (25 HP). The solar collection system incorporates east/west tracking parabolic trough collectors with a total aperture area of 1275 sq m (13,720 sq ft). The hot oil type thermal energy storage is sufficient for approximately 20 hours of power system operation. The system utilizes a reaction type turbine in conjunction with an organic Rankine cycle engine. Total collector field efficiency reaches a maximum of 20 percent near the winter solstice and about 50 percent during the summer. During the month of July, 1979, the system pumped 60 percent of the 35,300 cu m (28.6 acre-feet) of water delivered. Operating efficiencies for the turbine component, organic Rankine cycle engine and the complete power system are respectively 65 to 75 percent, 12 to 15 percent and 5 to 6 percent. Significant maintenance time was expended on both the collector and power systems throughout the operational period.

  17. [Investigation of the actual conditions of hospital nurses working on three rotating shifts: questionnaire results of shift work schedules, feelings of sleep and fatigue, and depression].

    PubMed

    Matsumoto, M; Kamata, S; Naoe, H; Mutoh, F; Chiba, S

    1996-01-01

    These studies were performed to clarify (1) the actual conditions concerning rotating shift schedules of nurses in Japanese university and college hospitals and to evaluate (2) some aspects of the physical and mental health, and (3) sleep profile of hospital nurses working on counter-clockwise shift rotation. Two questionnaire surveys and the OSA sleep inventory (OSA) were carried out. The subjects in the study (1) were a total of 80 nursing directors in university and college hospitals. The questionnaire covered 4 categories, such as the schedule most frequently adopted and reasons for using the schedule. The questionnaires were returned by 67 directors (83.8%). The subjects in the study (2) were 189 nurses working on three-shift work schedules at Asahikawa Medical College Hospital. The items in the questionnaire covered 7 categories, as follows: 1) feeling of sleep after each shift (8 items); 2) feeling of fatigue after each shift (30 items); 3) physical symptoms; 4) inter-personal problems; 5) all the items on Zung's self-rating depression scale (SDS); 6) all the items on the Horne and Ostberg morningness-eveningness questionnaire; and 7) 24 items on the Maudsley personality inventory. The questionnaires were returned by 156 nurses (82.5%), whose mean age and duration of shift-work employment were 27.2 +/- 5.1 and 5.0 +/- 4.3 years (mean +/- SD), respectively. For 152 nurses (97.4%) of those returning the questionnaire, the working schedule consisted of 2 consecutive night shifts and 2 consecutive evening shifts, following a variable number of day shifts (rapid and counterclockwise shift rotation). The subjects in the study (3) were 8 healthy nurses working on above-mentioned three rotating shifts at the psychiatric ward of Asahikawa Medical College Hospital, whose mean age was 29.4 +/- 5.8 years (mean +/- SD). All the subjects recorded their sleep-logs and underwent OSA everyday for 30 consecutive days. Of the 240 OSA data, 95 data (16 after day shift, 17 after

  18. The Houston Lightning Mapping Array: Installation, Operation, and Preliminary Results

    NASA Astrophysics Data System (ADS)

    Orville, R. E.; Cullen, M. R.; Rodeheffer, D.; Krehbiel, P. R.; Rison, W.

    2012-12-01

    The Houston Lightning Mapping Array (LMA) was established in April 2012 and is a network of twelve time-of-arrival lightning sensors operating in the VHF around Houston, Texas. The network sensors are built by New Mexico Institute of Mining and Technology. Built stand-alone units, these LMA sensors use solar panels and cellular data modems for Internet connectivity. This enables the units to be placed in strategic locations at sites to minimize noise and interference by reducing dependence on wired power or communications lines. Twelve sensors are distributed around the Houston and provide total lightning data for the fourth most populated American city. The primary research goals of the network are to investigate the structure of total lightning within thunderstorm development and to examine any potential impact of the urban environment on lightning characteristics. Furthermore, the proximity to the coast and the Gulf of Mexico presents the opportunity to examine the total lightning structure within tropical cyclones that impact the Texas coastline. The availability of real-time LMA data provides a decision support tool for advanced warning of thunderstorm development. We present efforts with the Houston/Galveston Weather Forecast Office and the Spaceflight Meteorology Group at Johnson Space Center to integrate the real-time LMA data into operational display software. The network of 12 sensors has been operating continuously since installation in mid-April with 10 sensors surrounding the Houston area plus one in College Station and one in Galveston. Analysis of recent data will investigate three-dimensional thunderstorm activity.

  19. Analysis of space tug operating techniques. Volume 2: Study results

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The design requirements for space tug systems and cost analysis of the refurbishment phases are discussed. The vehicle is an integral propulsion stage using liquid hydrogen and liquid oxygen as propellants and is capable of operating either as a fully or a partially autonomous vehicle. Structural features are an integral liquid hydrogen tank, a liquid oxygen tank, a meteoroid shield, an aft conical docking and structural support ring, and a staged combustion main engine. The vehicle is constructed of major modules for ease of maintenance. Line drawings and block diagrams are included to explain the maintenance requirements for the subsystems.

  20. Subtle lisfranc subluxation: results of operative and nonoperative treatment.

    PubMed

    Crates, John M; Barber, F Alan; Sanders, Eric J

    2015-01-01

    Subtle Lisfranc instability is typically a low-energy, twisting, axial-loading injury. The present study evaluated the operative treatment of subtle Lisfranc injuries after nonoperative failure. The data from consecutive patients with subtle Lisfranc instabilities were reviewed. Those in whom initial nonoperative treatment had failed underwent surgery. The American Orthopaedic Foot and Ankle Society (AOFAS) midfoot score was obtained initially, after nonoperative treatment, and, for those in whom nonoperative treatment had failed, after operative treatment. Of 36 patients enrolled, 16 (44.44%) were successfully treated nonoperatively, and 20 (55.56%) required surgery after nonoperative treatment had failed. Of those treated operatively, 9 (45%) were stabilized with dual screws and 11 (55%) with dual suture buttons. The mean follow-up period was 36 ± 12.2 months. The AOFAS scores significantly improved from the pre- to final post-treatment values. The overall mean pretreatment AOFAS score (62.8 ± 8.84) was significantly lower statistically than the mean overall post-treatment AOFAS score (91.3 ± 8.34; p < .0001). The mean AOFAS score before nonoperative treatment (61.9 ± 9.5) improved to a mean AOFAS score of 75.3 ± 15.8 after nonoperative treatment (p = .0029). The mean preoperative AOFAS score (63.5 ± 8.46) improved to a postoperative AOFAS score of 92.3 ± 8.43 (p < .0001). The mean AOFAS score before nonoperative treatment (61.9 ± 9.5) was not significantly different statistically from the mean preoperative AOFAS score (63.5 ± 8.46; p = .62). The mean AOFAS score after nonoperative treatment (75.3 ± 15.8) was lower than the mean postoperative AOFAS score (92.3 ± 8.43; p < .0001). Of the 9 feet stabilized with dual screws, 7 (77.78%) required screw removal during the observation period. Subtle Lisfranc injuries failing nonoperative treatment were successfully stabilized using either a dual screw or suture button technique. PMID:25746769

  1. Experimental Results from Initial Operation of Plasma Injector 1

    NASA Astrophysics Data System (ADS)

    Howard, Stephen

    2010-11-01

    General Fusion has begun operation of its first full-scale plasma injector, designed to accelerate high density spheromak plasmas into the compression chamber of a proposed MTF reactor. The geometry of Plasma Injector 1 (PI-1) is that of a two stage coaxial Marshal gun with a conical converging accelerator electrodes, similar in shape to the MARAUDER device, while pulsed power is applied in the same configuration as the RACE device. PI-1 is 5 meters in length and 1.9 m in diameter at the expansion region where a high aspect ratio (4.4) spheromak is formed with a minimum lambda of 9 m-1. The acceleration/compression stage is 4 m long and tapers to a final outer diameter of 40 cm. PI-1 is now operating at 1 MJ of total capacitor power, which will be doubled again before it reaches its design parameters. Diagnostics include 3 interferometer chords, 21 magnetic probes (2 axis poloidal/toroidal), 13 fast photodiode chords, as well as one Thomson scattering chord, a visible light survey spectrometer, and a Langmuir triple probe. Electrode voltage and current are also monitored. So far spheromaks of poloidal flux exceeding 100 mWb have been formed in the expansion region, and spheromaks of 40-50 mWb have been formed and accelerated out the end of the accelerator into a flux conserving target chamber. Expansion region densities are typically ˜5 x10^14cm-3, while conditions in the target chamber have reached ne˜10^16cm-3, and lifetimes of 300 μs.

  2. Remotely Operated Vehicles under sea ice - Experiences and results from five years of polar operations

    NASA Astrophysics Data System (ADS)

    Katlein, Christian; Arndt, Stefanie; Lange, Benjamin; Belter, Hans Jakob; Schiller, Martin; Nicolaus, Marcel

    2016-04-01

    The availability of advanced robotic technologies to the Earth Science community has largely increased in the last decade. Remotely operated vehicles (ROV) enable spatially extensive scientific investigations underneath the sea ice of the polar oceans, covering a larger range and longer diving times than divers with significantly lower risks. Here we present our experiences and scientific results acquired from ROV operations during the last five years in the Arctic and Antarctic sea ice region. Working under the sea ice means to have all obstacles and investigated objects above the vehicle, and thus changes several paradigms of ROV operations as compared to blue water applications. Observations of downwelling spectral irradiance and radiance allow a characterization of the optical properties of sea ice and the spatial variability of the energy partitioning across the atmosphere-ice-ocean boundary. Our results show that the decreasing thickness and age of the sea ice have led to a significant increase in light transmission during summer over the last three decades. Spatially extensive measurements from ROV surveys generally provide more information on the light field variability than single spot measurements. The large number of sampled ice conditions during five cruises with the German research icebreaker RV Polarstern allows for the investigations of the seasonal evolution of light transmittance. Both, measurements of hyperspectral light transmittance through sea ice, as well as classification of upward-looking camera images were used to investigate the spatial distribution of ice-algal biomass. Buoyant ice-algal aggregates were found to be positioned in the stretches of level ice, rather than pressure ridges due to a physical interaction of aggregate-buoyancy and under-ice currents. Synchronous measurements of sea ice thickness by upward looking sonar provides crucial additional information to put light-transmittance and biological observations into context

  3. Arsenic pilot plant operation and results:Weatherford, Oklahoma.

    SciTech Connect

    Aragon, Malynda Jo; Arora, H. (Narasimhan Consulting Services Inc., Phoenix, Arizona); Karori, Saqib (Narasimhan Consulting Services Inc., Phoenix, Arizona); Pathan, Sakib

    2007-05-01

    Narasimhan Consulting Services, Inc. (NCS), under a contract with the Sandia National Laboratories (SNL), designed and operated pilot scale evaluations of the adsorption and coagulation/filtration treatment technologies aimed at meeting the recently revised arsenic maximum contaminant level (MCL) for drinking water. The standard of 10 {micro}g/L (10 ppb) is effective as of January 2006. The pilot demonstration is a project of the Arsenic Water Technology Partnership program, a partnership between the American Water Works Association Research Foundation (AwwaRF), SNL and WERC (A Consortium for Environmental Education and Technology Development). The pilot evaluation was conducted at Well 30 of the City of Weatherford, OK, which supplies drinking water to a population of more than 10,400. Well water contained arsenic in the range of 16 to 29 ppb during the study. Four commercially available adsorption media were evaluated side by side for a period of three months. Both adsorption and coagulation/filtration effectively reduced arsenic from Well No.30. A preliminary economic analysis indicated that adsorption using an iron oxide media was more cost effective than the coagulation/ filtration technology.

  4. Operating experiences and test results of six cold helium compressors

    NASA Astrophysics Data System (ADS)

    Brown, D. P.; Gibbs, R. J.; Schlafke, A. P.; Sondericker, J. H.; Wu, K. C.

    Three small and three large cold helium centrifugal compressors have been operated at Brookhaven National Laboratory between 1981 and 1986. The three small cold compressors have been installed on a 1000 W refrigerator for testing a string of superconducting magnets and for R and D purposes. The three large units are components of the BNL 24.8 KW refrigerator to be used to provide cooling for the RHIC project. These compressors are used either to circulate a large amount of supercritical helium through a group of magnets or to pump on the helium bath to reduce temperature in the system. One small circulating compressor tested employs tilting-pad gas bearings and is driven by a DC motor. The two small cold vacuum pumps tested use oil bearings and are driven by oil turbines. The three large oil-bearing cold compressors are driven by DC motors through a gear box. A unique feature of the large vacuum pump is the combination of two pumps with a total of four stages on the same shaft. The adiabatic efficiencies are found to be 57% for the large vacuum pumps and close to 50% for the large circulating compressor. Good overall reliability has been experienced.

  5. Occipitocervical Fusion Surgery: Review of Operative Techniques and Results.

    PubMed

    Kukreja, Sunil; Ambekar, Sudheer; Sin, Anthony H; Nanda, Anil

    2015-09-01

    Objective Varying types of clinicoradiologic presentations at the craniovertebral junction (CVJ) influence the decision process for occipitocervical fusion (OCF) surgery. We discuss the operative techniques and decision-making process in OCF surgery based on our clinical experience and a literature review. Material and Methods A total of 49 consecutive patients who underwent OCF participated in the study. Sagittal computed tomography images were used to illustrate and measure radiologic parameters. We measured Wackenheim clivus baseline (WCB), clivus-canal angle (CCA), atlantodental distance (ADD), and Powers ratio (PR) in all the patients. Results Clinical improvement on Nurick grading was recorded in 36 patients. Patients with better preoperative status (Nurick grades 1-3) had better functional outcomes after the surgery (p = 0.077). Restoration of WCB, CCA, ADD, and PR parameters following the surgery was noted in 39.2%, 34.6%, 77.4%, and 63.3% of the patients, respectively. Complications included deep wound infections (n = 2), pseudoarthrosis (n = 2), and deaths (n = 4). Conclusion Conventional wire-based constructs are superseded by more rigid screw-based designs. Odontoidectomy is associated with a high incidence of perioperative complications. The advent of newer implants and reduction techniques around the CVJ has obviated the need for this procedure in most patients. PMID:26401473

  6. CITY OF SANTA FE V. KOMIS REVISITED: AN ANALYSIS OF THE ACTUAL IMPACTS OF CONSTRUCTION AND OPERATION OF THE SANTA FE BYPASS ON THE VALUE OF NEARBY REAL ESTATE

    SciTech Connect

    Bentz, Dr. E. J., Jr.,; Bentz, C. B.; O'Hora, T. D.; Baepler, Dr. D.

    2003-02-27

    The Santa Fe Bypass for transport of transuranic waste (TRU) to the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico has been constructed and is operational (as of 2000). This paper presents a review of actual empirical data from the sales of real estate in the Santa Fe City/County area since the filing of the City of Santa Fe v. Komis lawsuit in 1988. The data analyzed covers the time period from 1989 through the last quarter of 2001.

  7. Arsenic pilot plant operation and results : Anthony, New Mexico.

    SciTech Connect

    Aragon, Malynda Jo; Everett, Randy L.; Siegel, Malcolm Dean; Aragon, Alicia R.; Kottenstette, Richard Joseph; Holub, William E., Jr.; Wright, Jerome L.; Dwyer, Brian P.

    2007-09-01

    Sandia National Laboratories (SNL) is conducting pilot scale evaluations of the performance and cost of innovative water treatment technologies aimed at meeting the recently revised arsenic maximum contaminant level (MCL) for drinking water. The standard of 10 {micro}g/L (10 ppb) is effective as of January 2006. The pilot tests have been conducted in New Mexico where over 90 sites that exceed the new MCL have been identified by the New Mexico Environment Department. The pilot test described in this report was conducted in Anthony, New Mexico between August 2005 and December 2006 at Desert Sands Mutual Domestic Water Consumers Association (MDWCA) (Desert Sands) Well No.3. The pilot demonstrations are a part of the Arsenic Water Technology Partnership program, a partnership between the American Water Works Association Research Foundation (AwwaRF), SNL and WERC (A Consortium for Environmental Education and Technology Development). The Sandia National Laboratories pilot demonstration at the Desert Sands site obtained arsenic removal performance data for fourteen different adsorptive media under intermittent flow conditions. Well water at Desert Sands has approximately 20 ppb arsenic in the unoxidized (arsenite-As(III)) redox state with moderately high total dissolved solids (TDS), mainly due to high sulfate, chloride, and varying concentrations of iron. The water is slightly alkaline with a pH near 8. The study provides estimates of the capacity (bed volumes until breakthrough at 10 ppb arsenic) of adsorptive media in the same chlorinated water. Adsorptive media were compared side-by-side in ambient pH water with intermittent flow operation. This pilot is broken down into four phases, which occurred sequentially, however the phases overlapped in most cases.

  8. TEST RESULTS FOR FUEL-CELL OPERATION ON LANDFILL GAS

    EPA Science Inventory

    Test results from a demonstration of fuel-cell (FC) energy recovery and control of landfill gas emissions are presented. The project addressed two major issues: (i) the design, construction, and testing of a landfill-gas cleanup system; and (ii) a field test of a commercial phos...

  9. Space Launch System Base Heating Test: Experimental Operations & Results

    NASA Technical Reports Server (NTRS)

    Dufrene, Aaron; Mehta, Manish; MacLean, Matthew; Seaford, Mark; Holden, Michael

    2016-01-01

    NASA's Space Launch System (SLS) uses four clustered liquid rocket engines along with two solid rocket boosters. The interaction between all six rocket exhaust plumes will produce a complex and severe thermal environment in the base of the vehicle. This work focuses on a recent 2% scale, hot-fire SLS base heating test. These base heating tests are short-duration tests executed with chamber pressures near the full-scale values with gaseous hydrogen/oxygen engines and RSRMV analogous solid propellant motors. The LENS II shock tunnel/Ludwieg tube tunnel was used at or near flight duplicated conditions up to Mach 5. Model development was based on the Space Shuttle base heating tests with several improvements including doubling of the maximum chamber pressures and duplication of freestream conditions. Test methodology and conditions are presented, and base heating results from 76 runs are reported in non-dimensional form. Regions of high heating are identified and comparisons of various configuration and conditions are highlighted. Base pressure and radiometer results are also reported.

  10. CMS tracking performance results from early LHC operation

    SciTech Connect

    Khachatryan, Vardan; et al.

    2010-11-24

    The first LHC pp collisions at centre-of-mass energies of 0.9 and 2.36 TeV were recorded by the CMS detector in December 2009. The trajectories of charged particles produced in the collisions were reconstructed using the all-silicon Tracker and their momenta were measured in the 3.8 T axial magnetic field. Results from the Tracker commissioning are presented including studies of timing, efficiency, signal-to-noise, resolution, and ionization energy. Reconstructed tracks are used to benchmark the performance in terms of track and vertex resolutions, reconstruction of decays, estimation of ionization energy loss, as well as identification of photon conversions, nuclear interactions, and heavy-flavour decays.

  11. The PLCO Cancer Screening Trial: Background, Goals, Organization, Operations, Results.

    PubMed

    Gohagan, John K; Prorok, Philip C; Greenwald, Peter; Kramer, Barnett S

    2015-01-01

    The randomized PLCO trial was designed to answer four primary questions: does screening for these cancers using often promoted tests reduce cancer-specific mortality? Nearly 155,000 men and women were allocated to screening or usual care arms in a 1:1 ratio under a centralized, secure randomization algorithm at ten competitively selected screening centers nationwide. Screened men received PSA blood tests and digital rectal examinations. Screened women received CA125 blood tests and trans-vaginal ultrasound. Both men and women in the screened arm received anterolateral view chest x-ray and 60 cm flexible sigmoidoscopy. Blood specimens were collected at each screening visit and buccal cell DNA was collected once from the usual care participants. Histology slides were collected for cancer cases. Participants completed a baseline questionnaire covering health and risk factors and a dietary questionnaire. Data collected on standardized machine-readable forms were scanned remotely at screening and laboratory sites utilizing PLCO dedicated, NCI provided and configured computer systems for quality checks, archiving, and analysis. Comprehensive quality assurance was implemented over recruitment, consenting, randomization, screening, data management, records keeping, patient-specific screening results reporting, follow-up, and data analysis. Performance and data quality were monitored on-site and remotely by data edits, site visits, and random record audits. Specially trained and certified professionals performed screening procedures and medical record abstracting. An independent committee of medical specialists reviewed and certified case-specific cause of death. Scientific leadership was provided by NCI Project Officers, PLCO principal investigators, external consultants, and an independent data and safety monitoring board. PMID:26238115

  12. RendezVous sensor for automatic guidance of transfer vehicles to ISS concept of the operational modes depending on actual optical and geometrical-dynamical conditions

    NASA Astrophysics Data System (ADS)

    Moebius, Bettina G.; Kolk, Karl-Hermann

    2000-10-01

    Based on an ATV RendezVous Predevelopment Program initiated by ESTEC, an automatically operating Rendez Vous Sensor has been developed. The sensor--a Scanning Tele-Goniometer--shall guide docking and retreat of the European Automatic Transfer Vehicle as well as berthing and retreat of the Japanese H-II Transfer Vehicle. The sensor performance will be strongly connected with the properties of cooperative targets, consisting of an arrangement of retro reflectors mounted on ISS each.

  13. Analysis of remote operating systems for space-based servicing operations. Volume 2: Study results

    NASA Technical Reports Server (NTRS)

    1985-01-01

    The developments in automation and robotics have increased the importance of applications for space based servicing using remotely operated systems. A study on three basic remote operating systems (teleoperation, telepresence and robotics) was performed in two phases. In phase one, requirements development, which consisted of one three-month task, a group of ten missions were selected. These included the servicing of user equipment on the station and the servicing of the station itself. In phase two, concepts development, which consisted of three tasks, overall system concepts were developed for the selected missions. These concepts, which include worksite servicing equipment, a carrier system, and payload handling equipment, were evaluated relative to the configurations of the overall worksite. It is found that the robotic/teleoperator concepts are appropriate for relatively simple structured tasks, while the telepresence/teleoperator concepts are applicable for missions that are complex, unstructured tasks.

  14. An integrated system for improving design team performance and for measuring operability results

    SciTech Connect

    McCuish, J.D.; Wilson, J.L.; Hallam, J.L.

    1995-12-31

    Operability is defined as the effectiveness of the facility in performing as designed upon commissioning and is measured principally in the first 6 - 12 months of new operation. Generally in the construction and installation of production facilities, teams have had few tools or generally accepted practices for impacting the effective Operability of the facility, measuring that Operability, and linking the two. This paper describes a recent study of a significant number of projects incorporating operability results and other information gathered from world-wide subject-matter experts and the subsequent development of new tools to improve Operability performance. Presented are the data analyses methodology, results and new tools for predicting the likelihood of project operability success several years ahead of commissioning. This paper describes the Operability Toolbox method to measure and improve Operability effectiveness.

  15. Linguistic Theory and Actual Language.

    ERIC Educational Resources Information Center

    Segerdahl, Par

    1995-01-01

    Examines Noam Chomsky's (1957) discussion of "grammaticalness" and the role of linguistics in the "correct" way of speaking and writing. It is argued that the concern of linguistics with the tools of grammar has resulted in confusion, with the tools becoming mixed up with the actual language, thereby becoming the central element in a metaphysical…

  16. The Self Actualized Reader.

    ERIC Educational Resources Information Center

    Marino, Michael; Moylan, Mary Elizabeth

    A study examined the commonalities that "voracious" readers share, and how their experiences can guide parents, teachers, and librarians in assisting children to become self-actualized readers. Subjects, 25 adults ranging in age from 20 to 67 years, completed a questionnaire concerning their reading histories and habits. Respondents varied in…

  17. 49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Restrictive condition resulting from open hand... Instructions; Roadway § 236.528 Restrictive condition resulting from open hand-operated switch; requirement. When a facing point hand-operated switch is open one-fourth inch or more, a trailing point...

  18. 49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Restrictive condition resulting from open hand... Instructions; Roadway § 236.528 Restrictive condition resulting from open hand-operated switch; requirement. When a facing point hand-operated switch is open one-fourth inch or more, a trailing point...

  19. 49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Restrictive condition resulting from open hand... Instructions; Roadway § 236.528 Restrictive condition resulting from open hand-operated switch; requirement. When a facing point hand-operated switch is open one-fourth inch or more, a trailing point...

  20. 49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Restrictive condition resulting from open hand... Instructions; Roadway § 236.528 Restrictive condition resulting from open hand-operated switch; requirement. When a facing point hand-operated switch is open one-fourth inch or more, a trailing point...

  1. 49 CFR 236.528 - Restrictive condition resulting from open hand-operated switch; requirement.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Restrictive condition resulting from open hand... Instructions; Roadway § 236.528 Restrictive condition resulting from open hand-operated switch; requirement. When a facing point hand-operated switch is open one-fourth inch or more, a trailing point...

  2. 49 CFR 1560.107 - Use of watch list matching results by covered aircraft operators.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... SECURE FLIGHT PROGRAM Collection and Transmission of Secure Flight Passenger Data for Watch List Matching § 1560.107 Use of watch list matching results by covered aircraft operators. A covered aircraft operator... 49 Transportation 9 2010-10-01 2010-10-01 false Use of watch list matching results by...

  3. How People Actually Use Thermostats

    SciTech Connect

    Meier, Alan; Aragon, Cecilia; Hurwitz, Becky; Mujumdar, Dhawal; Peffer, Therese; Perry, Daniel; Pritoni, Marco

    2010-08-15

    Residential thermostats have been a key element in controlling heating and cooling systems for over sixty years. However, today's modern programmable thermostats (PTs) are complicated and difficult for users to understand, leading to errors in operation and wasted energy. Four separate tests of usability were conducted in preparation for a larger study. These tests included personal interviews, an on-line survey, photographing actual thermostat settings, and measurements of ability to accomplish four tasks related to effective use of a PT. The interviews revealed that many occupants used the PT as an on-off switch and most demonstrated little knowledge of how to operate it. The on-line survey found that 89% of the respondents rarely or never used the PT to set a weekday or weekend program. The photographic survey (in low income homes) found that only 30% of the PTs were actually programmed. In the usability test, we found that we could quantify the difference in usability of two PTs as measured in time to accomplish tasks. Users accomplished the tasks in consistently shorter times with the touchscreen unit than with buttons. None of these studies are representative of the entire population of users but, together, they illustrate the importance of improving user interfaces in PTs.

  4. The actual goals of geoethics

    NASA Astrophysics Data System (ADS)

    Nemec, Vaclav

    2014-05-01

    The most actual goals of geoethics have been formulated as results of the International Conference on Geoethics (October 2013) held at the geoethics birth-place Pribram (Czech Republic): In the sphere of education and public enlightenment an appropriate needed minimum know how of Earth sciences should be intensively promoted together with cultivating ethical way of thinking and acting for the sustainable well-being of the society. The actual activities of the Intergovernmental Panel of Climate Changes are not sustainable with the existing knowledge of the Earth sciences (as presented in the results of the 33rd and 34th International Geological Congresses). This knowledge should be incorporated into any further work of the IPCC. In the sphere of legislation in a large international co-operation following steps are needed: - to re-formulate the term of a "false alarm" and its legal consequences, - to demand very consequently the needed evaluation of existing risks, - to solve problems of rights of individuals and minorities in cases of the optimum use of mineral resources and of the optimum protection of the local population against emergency dangers and disasters; common good (well-being) must be considered as the priority when solving ethical dilemmas. The precaution principle should be applied in any decision making process. Earth scientists presenting their expert opinions are not exempted from civil, administrative or even criminal liabilities. Details must be established by national law and jurisprudence. The well known case of the L'Aquila earthquake (2009) should serve as a serious warning because of the proven misuse of geoethics for protecting top Italian seismologists responsible and sentenced for their inadequate superficial behaviour causing lot of human victims. Another recent scandal with the Himalayan fossil fraud will be also documented. A support is needed for any effort to analyze and to disclose the problems of the deformation of the contemporary

  5. Pilot Eye Scanning under Actual Single Pilot Instrument Flight

    NASA Astrophysics Data System (ADS)

    Rinoie, Kenichi; Sunada, Yasuto

    Operations under single pilot instrument flight rules for general aviation aircraft is known to be one of the most demanding pilot tasks. Scanning numerous instruments plays a key role for perception and decision-making during flight. Flight experiments have been done by a single engine light airplane to investigate the pilot eye scanning technique for IFR flights. Comparisons between the results by an actual flight and those by a PC-based flight simulator are made. The experimental difficulties of pilot eye scanning measurements during the actual IFR flight are discussed.

  6. AMICA at Dome C: results from the first year of automatic operation tests in Antarctica

    NASA Astrophysics Data System (ADS)

    Dolci, M.; Valentini, A.; Ragni, M.; Di Cianno, A.; Di Rico, G.; Straniero, O.; Romano, D.; Christille, J.-M.; Piluso, A.

    2012-09-01

    Results from the first year of AMICA operations at Dome C are presented. AMICA is an astronomical camera for imaging between 2 and 24 μm designed to work automatically at the extreme conditions of Antarctica. Except for the cryostat, AMICA devices are hosted inside a rack whose operating conditions are automatically controlled. 120 days of environmental tests data have been obtained in 2011. The data concern the operating parameters of the system. The results show an excellent performance. A quality factor is computed as a function of the external conditions and a few critical correcting actions are described.

  7. Feasibility Study of a Rotorcraft Health and Usage Monitoring System (HUMS): Results of Operator's Evaluation

    NASA Technical Reports Server (NTRS)

    Romero, Raylund; Summers, Harold; Cronkhite, James

    1996-01-01

    The objective was to evaluate the feasibility of a state-of-the-art health and usage monitoring system (HUMS) to provide monitoring of critical mechanical systems on the helicopter, including motors, drive train, engines, and life-limited components. The implementation of HUMS and cost integration with current maintenance procedures was assessed from the operator's viewpoint in order to achieve expected benefits from these systems, such as enhanced safety, reduced maintenance cost, and increased availability. An operational HUMS that was installed and operated under an independent flight trial program was used as a basis for this study. The HUMS equipment and software were commercially available. Based on the results of the feasibility study, the HUMS used in the flight trial program generally demonstrated a high level of reliability in monitoring the rotor system, engines, drive train, and life-limited components. The system acted as a sentinel to warn of impending failures. A worn tail rotor pitch bearing was detected by HUMS, which had the capability for self testing to diagnose system and sensor faults. Examples of potential payback to the operator with HUMS were identified, including reduced insurance cost through enhanced safety, lower operating costs derived from maintenance credits, increased aircraft availability, and improved operating efficiency. The interfacing of HUMS with current operational procedures was assessed to require only minimal revisions to the operator's maintenance manuals. Finally the success in realizing the potential benefits from HUMS technology was found to depend on the operator, helicopter manufacturer, regulator (FAA), and HUMS supplier working together.

  8. Moral Reasoning in Hypothetical and Actual Situations.

    ERIC Educational Resources Information Center

    Sumprer, Gerard F.; Butter, Eliot J.

    1978-01-01

    Results of this investigation suggest that moral reasoning of college students, when assessed using the DIT format, is the same whether the dilemmas involve hypothetical or actual situations. Subjects, when presented with hypothetical situations, become deeply immersed in them and respond as if they were actual participants. (Author/BEF)

  9. Study Results on Knowledge Requirements for Entry-Level Airport Operations and Management Personnel

    NASA Technical Reports Server (NTRS)

    Quilty, Stephen M.

    2005-01-01

    This paper identifies important topical knowledge areas required of individuals employed in airport operations and management positions. A total of 116 airport managers and airfield operations personnel responded to a survey that sought to identify the importance of various subject matter for entry level airport operations personnel. The results from this study add to the body of research on aviation management curriculum development and can be used to better develop university curriculum and supplemental training focused on airport management and operations. Recommendations are made for specialized airport courses within aviation management programs. Further, this study identifies for job seekers or individuals employed in entry level positions those knowledge requirements deemed important by airport managers and operations personnel at different sized airports.

  10. Results of prototype software development for automation of shuttle proximity operations

    NASA Technical Reports Server (NTRS)

    Hiers, Hal; Olszweski, Oscar

    1991-01-01

    The effort involves demonstration of expert system technology application to Shuttle rendezvous operations in a high-fidelity, real-time simulation environment. The JSC Systems Engineering Simulator (SES) served as the test bed for the demonstration. Rendezvous applications were focused on crew procedures and monitoring of sensor health and trajectory status. Proximity operations applications were focused on monitoring, crew advisory, and control of the approach trajectory. Guidance, Navigation, and Control areas of emphasis included the approach, transition and stationkeeping guidance, and laser docking sensor navigation. Operator interface displays for monitor and control functions were developed. A rule-based expert system was developed to manage the relative navigation system/sensors for nominal operations and simple failure contingencies. Testing resulted in the following findings; (1) the developed guidance is applicable for operations with LVLH stabilized targets; (2) closing rates less than 0.05 feet per second are difficult to maintain due to the Shuttle translational/rotational cross-coupling; (3) automated operations result in reduced propellant consumption and plume impingement effects on the target as compared to manual operations; and (4) braking gates are beneficial for trajectory management. A versatile guidance design was demonstrated. An accurate proximity operations sensor/navigation system to provide relative attitude information within 30 feet is required and redesign of the existing Shuttle digital autopilot should be considered to reduce the cross-coupling effects. This activity has demonstrated the feasibility of automated Shuttle proximity operations with the Space Station Freedom. Indications are that berthing operations as well as docking can be supported.

  11. Combining water budgets and IFIM results for analyzing operation alternatives at peaking projects

    SciTech Connect

    Conners, M.E.; Homa, J. Jr.; Carrington, G.

    1995-12-31

    Licensing of hydropower projects often involves evaluating and comparing several different alternatives for project operation. Projects with peaking capabilities, in particular, are frequently required to compare peaking operation with substantially different alternatives, such as continuous run-of-the-river flows. Instream flow studies are used to assess the environmental impacts of hydropower operation by modeling the amount of aquatic habitat available at various flows. It can be difficult, however, to apply instream flow models downstream of peaking operations, or to present habitat model results in a way that clearly compares operation alternatives. This paper presents a two-stage analysis that was used in the successful negotiation of a licensing settlement for Niagara Mohawk Power Corporation`s Salmon River Project in upstate New York. A water budget model based on project configuration was used to compile flow-duration curves for the project under several alternative operating rules. A spreadsheet model was developed that combines the results of instream flow habitat models with flow-duration statistics. This approach provides a clear, quantitative comparison of the effect of alternative project operations on downstream aquatic habitat.

  12. Steady-State Operation Scenario and the First Experimental Result on QUEST

    SciTech Connect

    Hanada, K; Peng, Yueng Kay Martin

    2010-01-01

    QUEST focuses on the steady state operation of the spherical tokamak by controlled PWI and electron Bernstein wave current drive. One of the main purposes of QUEST is an achievement of long duration discharge with MW-class injected power. As the result, QUEST should be operated in the challenging region on heat and particle handling. To do the particle handling, high temperature all metal wall up to 623 K and closed divertors are planned, which is to realize the steady-state operation under recycling ratio, R = 1. This is a dispensable check to DEMO, because wall pumping should be avoided as possible in the view of tritium retention. The QUEST project will be developed in increment step such as, I. low steady state operation in limiter configuration, II. low steady state operation in divertor configuration, III. relatively high steady state operation in closed divertor configuration. Phase I in the project corresponds to these two years, and final goal of phase I is to make full current drive plasma up to 20 kA. Closed divertor will be designed and tested in the Phase II. QUEST is running from Oct., 2008 and the first results are introduced.

  13. Changes in the cardiac muscle electric activity as a result of Coronary Artery Bypass Graft operation

    NASA Astrophysics Data System (ADS)

    Grajek, Magdalena; Krzyminiewski, Ryszard; Kalawski, Ryszard; Kulczak, Mariusz

    2008-01-01

    Many bioelectric signals have a complex internal structure that can be a rich source of information on the tissue or cell processes. The structure of such signals can be analysed in detail by applying digital methods of signal processing. Therefore, of substantial use in diagnosis of the coronary arterial disease is the method of digital enhancement of increasing signal resolution ECG (NURSE-ECG), permitting detection of temporary changes in the electric potentials in the cardiac muscle in the process of depolarisation. Thanks to the application of NURSE-ECG it has become possible to detect relatively small changes in the electric activity of particular fragments of the cardiac muscle undetectable by the standard ECG method, caused by ischemia, the effect of a drug or infarct. The aim of this study was to identify and analyse changes in the electric activity of the cardiac muscle as a result of the Coronary Artery Bypass Graft (CABG) operation. In this study the method of NURSE-ECG has been applied in order to identify and analyse changes in the electric activity of the cardiac muscle as a result of the CABG operation. In the study performed in cooperation of the Institute of Physics Adam Mickiewicz University and the Strus Hospital, Cardiac Surgery Ward, 37 patients with advanced coronary arterial disease were asked to participate. The patients were examined prior to the operation, on the day after the operation and two months after the operation and a year after the operation. The ECG recordings were subjected to a numerical procedure of resolution enhancement by a NURSE-ECG program to reveal the tentative changes in the electric potential of the cardiac muscle on its depolarisation. Results of the study have shown that the NURSE ECG method can be applied to monitor changes in the electric activity of the cardiac muscle occurring as a result of CABG operation. One the second day after the operation in the majority of patients (70%) a rapid decrease of the total

  14. Operational results for the experimental DOE/NASA Mod-OA wind turbine project

    NASA Technical Reports Server (NTRS)

    Shaltens, R. K.; Birchenough, A. G.

    1983-01-01

    The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

  15. FY 1993 progress report on the ANS thermal-hydraulic test loop operation and results

    SciTech Connect

    Siman-Tov, M.; Felde, D.K.; Farquharson, G.

    1994-07-01

    The Thermal-Hydraulic Test Loop (THTL) is an experimental facility constructed to support the development of the Advanced Neutron Source Reactor (ANSR) at Oak Ridge National Laboratory (ORNL). Highly subcooled heavy-water coolant flows vertically upward at a very high mass flux of almost 27 MG/m{sup 2}-s. In a parallel fuel plate configuration as in the ANSR, the flow is subject to a potential excursive static-flow instability that can very rapidly lead to flow starvation and departure from nucleate boiling (DNB) in the ``hot channel``. The current correlations and experimental data bases for flow excursion (FE) and critical heat flux (CHF) seldom evaluate the specific combination of ANSR operating parameters. The THTL facility was designed and built to provide known thermal-hydraulic (T/H) conditions for a simulated full-length coolant subchannel of the ANS reactor core, thus facilitating experimental determination of FE and CHF thermal limits under expected ANSR T/H conditions. A series of FE tests with water flowing vertically upward was completed over a nominal heat flux range of 6 to 17 MW/m{sup 2}, a mass flux range of 8 to 28 Mg/m{sup 2}-s, an exit pressure range of 1.4 to 2.1 MPa, and an inlet temperature range of 40 to 50 C. FE experiments were also conducted using as ``soft`` a system as possible to secure a true FE phenomena (actual secondary burnout). True DNB experiments under similar conditions were also conducted. To the author`s knowledge, no other FE data have been reported in the literature to date that dover such a combination of conditions of high mass flux, high heat flux, and moderately high pressure.

  16. Seeded free electron laser operating with two colors: Comments on experimental results

    NASA Astrophysics Data System (ADS)

    Carpanese, M.; Ciocci, F.; Dattoli, G.; Petralia, A.; Petrillo, V.; Torre, A.

    2016-05-01

    Free electron lasers operating with two colors are promising devices for applications. The relevant modelization has provided a good understanding of the underlying physics. In this paper we present an analysis of the experimental results obtained at SPARC_LAB concerning seeded two-colors free electron laser (FEL) operation. The use of an ad hoc developed semi-analytical model based on the small-signal FEL integral equation reproduces most of the observed phenomenology. The paper discusses the reliability of the proposed method, the range of validity and its possible improvement.

  17. High Temperature Electrolysis 4 kW Experiment Design, Operation, and Results

    SciTech Connect

    J.E. O'Brien; X. Zhang; K. DeWall; L. Moore-McAteer; G. Tao

    2012-09-01

    This report provides results of long-term stack testing completed in the new high-temperature steam electrolysis multi-kW test facility recently developed at INL. The report includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. This facility has provided a demonstration of high-temperature steam electrolysis operation at the 4 kW scale with advanced cell and stack technology. This successful large-scale demonstration of high-temperature steam electrolysis will help to advance the technology toward near-term commercialization.

  18. Screening Analysis : Volume 2, Impact Results (Columbia River System Operation Review).

    SciTech Connect

    Not Available

    1992-06-01

    Detailed results from all of the work groups are presented in this chapter. Ninety alternatives were analyzed during the screening process. Three of the alternative represent various base cases and are used for comparison purposes. The other 87 alternatives represent a wide variety of operational possibilities ranging from current operations to emphasizing a single river use to compromise operations that attempt to accommodate the multiple uses. Every possible alternative suggested during the screening phase was considered. Each alternative was given an abbreviated name, a number and assigned by ROSE to either the Corps (C) or BPA (B) for hydroregulation modeling. A list of the alternatives with its number and hydroregulation assignment is given below. The results in this chapter are presented in numerical order. The first 3 letters in the name identify which work group suggested the alternative. The format for the results includes a brief description of each alternative, a tabulation of the screening calculations organized by work group, and observations/comments on the alternative by the work groups. The description summarizes the key operational requirements for the alternative and was taken directly from the instructions given to the hydroregulation modelers.

  19. Results of Operative and Nonoperative Treatment of Rockwood Types III and V Acromioclavicular Joint Dislocation

    PubMed Central

    Joukainen, Antti; Kröger, Heikki; Niemitukia, Lea; Mäkelä, E. Antero; Väätäinen, Urho

    2014-01-01

    Background: The optimal treatment of acute, complete dislocation of the acromioclavicular joint (ACJ) is still unresolved. Purpose: To determine the difference between operative and nonoperative treatment in acute Rockwood types III and V ACJ dislocation. Study Design: Randomized controlled trial; Level of evidence, 2. Methods: In the operative treatment group, the ACJ was reduced and fixed with 2 transarticular Kirschner wires and ACJ ligament suturing. The Kirschner wires were extracted after 6 weeks. Nonoperatively treated patients received a reduction splint for 4 weeks. At the 18- to 20-year follow-up, the Constant, University of California at Los Angeles Shoulder Rating Scale (UCLA), Larsen, and Simple Shoulder Test (SST) scores were obtained, and clinical and radiographic examinations of both shoulders were performed. Results: Twenty-five of 35 potential patients were examined at the 18- to 20-year follow-up. There were 11 patients with Rockwood type III and 14 with type V dislocations. Delayed surgical treatment for ACJ was used in 2 patients during follow-up: 1 in the operatively treated group and 1 in the nonoperatively treated group. Clinically, ACJs were statistically significantly less prominent or unstable in the operative group than in the nonoperative group (normal/prominent/unstable: 9/4/3 and 0/6/3, respectively; P = .02) and in the operative type III (P = .03) but not type V dislocation groups. In operatively and nonoperatively treated patients, the mean Constant scores were 83 and 85, UCLA scores 25 and 27, Larsen scores 11 and 11, and SST scores 11 and 12 at follow-up, respectively. There were no statistically significant differences in type III and type V dislocations. In the radiographic analysis, the ACJ was wider in the nonoperative than the operative group (8.3 vs 3.4 mm; P = .004), and in the type V dislocations (nonoperative vs operative: 8.5 vs 2.4 mm; P = .007). There was no statistically significant difference between study groups in

  20. Commissioning and operational results of the 12 GeV helium compression system at Jlab

    SciTech Connect

    Knudsen, Peter N.; Ganni, Venkatarao; Dixon, Kelly D.; Norton, Robert O.; Creel, Jonathan D.

    2015-12-01

    The new compressor system at Jefferson Lab (JLab) for the 12 GeV upgrade was commissioned in the spring of 2013 and incorporates many design changes, discussed in previous publications, to improve the operational range, efficiency, reliability and maintainability as compared to previous compressor skids used for this application. The 12 GeV helium compression system has five compressors configured with four pressure levels supporting three pressure levels in the new cold box. During compressor commissioning the compressors were operated independent of the cold box over a wide range of process conditions to verify proper performance including adequate cooling and oil removal. Isothermal and volumetric efficiencies over these process conditions for several built-involume ratios were obtained. This paper will discuss the operational envelope results and the modifications/improvements incorporated into the skids.

  1. Convexity of Energy-Like Functions: Theoretical Results and Applications to Power System Operations

    SciTech Connect

    Dvijotham, Krishnamurthy; Chertkov, Michael; Low, Steven

    2015-01-22

    Power systems are undergoing unprecedented transformations with increased adoption of renewables and distributed generation, as well as the adoption of demand response programs. All of these changes, while making the grid more responsive and potentially more efficient, pose significant challenges for power systems operators. Conventional operational paradigms are no longer sufficient as the power system may no longer have big dispatchable generators with sufficient positive and negative reserves. This increases the need for tools and algorithms that can efficiently predict safe regions of operation of the power system. In this paper, we study energy functions as a tool to design algorithms for various operational problems in power systems. These have a long history in power systems and have been primarily applied to transient stability problems. In this paper, we take a new look at power systems, focusing on an aspect that has previously received little attention: Convexity. We characterize the domain of voltage magnitudes and phases within which the energy function is convex in these variables. We show that this corresponds naturally with standard operational constraints imposed in power systems. We show that power of equations can be solved using this approach, as long as the solution lies within the convexity domain. We outline various desirable properties of solutions in the convexity domain and present simple numerical illustrations supporting our results.

  2. Operation results of the first commercial PFBC plant with high temperature ceramic filters

    SciTech Connect

    Kaneko, S.; Suga, N.

    1998-07-01

    Trial operation is now successfully underway at Tomato-Atsuma Unit No. 3 of Hokkaido Electric Power Co. (HEPCO) in Japan. This newly built 85 MWe unit is an innovative PFBC plant, which is the first commercial PFBC in Japan, and equipped with full capacity ceramic filters operated at 850 C. The high temperature ceramic filter effectively removes dusts in the hot gas and the dust loading at gas turbine inlet is much less than that of two-stage cyclones, minimizing the cost and time of gas turbine maintenance. The PFBC plant is composed of a pressurized fluidized-bed boiler, cyclones, ceramic filters, a gas turbine, a steam turbine, etc. and all of the equipment were manufactured and supplied by Mitsubishi Heavy Industries, Ltd. (MHI). Joint R and D program between HEPCO and MHI started 7 years ago, based on their own private funding and without any financial supports from public sectors, studying the optimum design of the first commercial PFBC aiming at environmental and economical advantages. And now fruitful results have been achieved. The commercial operation will start in March 1998 or earlier. Several troubles had been experienced during initial trial operation stage including pressure drop increase in ceramic filters. All these problems were solved one by one by the joint efforts of HEPCO and MHO. Load rejection tests, load swing tests, and automatic power control tests were successfully done in the spring of 1997. And tests with various kinds of coals are scheduled before the commercial operation.

  3. Bariatric Surgery in University Clinic Center Tuzla - Results After 30 Operations

    PubMed Central

    Ahmetasevic, Emir; Pasic, Fuad; Beslin, Miroslav Bekavac; Ilic, Miroslav; Ahmetasevic, Dzenita; Mesic, Mirza

    2016-01-01

    Introduction: Project of Bariatric surgery in University clinic center (UCC) Tuzla has been initiated in 2009 as an idea of professor Dešo Mešić and soon after that Bariatric surgical team led by doctor Fuad Pasic has been created. Material and methods: Practical team education was realized in Croatia in hospital „Sisters of Mercy” under supervision of professor Miroslav-Bekavac Beslin. First bariatric operations in UCC Tuzla has been done in 2011 and it was biliopancreatic diversion (BPD) Scopinaro. Results and discussion: So far there has been done 30 operations and among them there have been used almost all operative modalities - restrictive, malabsorptive and combined (laparoscopic gastric banding-LAPGB, Roux-y mini gastric bypass, open and laparoscopic gastric sleeve resection, and over mentioned Scopinaro’s BPD). Beginning results are very promising according to the fact that almost all operated patients after one year stopped using antihypertensive, antidiabetic and antidepressant therapy, that average year’s weight loss is 35-100 kilograms and total satisfactions of patients after surgeries is obvious. PMID:27147808

  4. More screen operation than calling: the results of observing cyclists' behaviour while using mobile phones.

    PubMed

    de Waard, Dick; Westerhuis, Frank; Lewis-Evans, Ben

    2015-03-01

    Operating a mobile telephone while riding a bicycle is fairly common practice in the Netherlands, yet it is unknown if this use is stable or increasing. As such, whether the prevalence of mobile phone use while cycling has changed over the past five years was studied via on-road observation. In addition the impact of mobile phone use on lateral position, i.e. distance from the front wheel to the curb, was also examined to see if it compared to the results seen in previous experimental studies. Bicyclists were observed at six different locations and their behaviour was scored. It was found that compared to five years ago the use of mobile phones while cycling has changed, not in frequency, but in how cyclists were operating their phones. As found in 2008, three percent of the bicyclists were observed to be operating a phone, but a shift from calling (0.7% of cyclists observed) to operating (typing, texting, 2.3% of cyclists) was found. In 2008 nearly the complete opposite usage was observed: 2.2% of the cyclists were calling and 0.6% was texting. Another finding was that effects on lateral position were similar to those seen in experimental studies in that cyclists using a phone maintained a cycling position which was further away from the curb. It was also found that when at an intersection, cyclist's operating their phone made less head movements to the right than cyclists who were just cycling. This shift from calling to screen operation, when combined with the finding related to reduced head movements at intersections, is worrying and potentially dangerous. PMID:25590920

  5. Application of auditory signals to the operation of an agricultural vehicle: results of pilot testing.

    PubMed

    Karimi, D; Mondor, T A; Mann, D D

    2008-01-01

    The operation of agricultural vehicles is a multitask activity that requires proper distribution of attentional resources. Human factors theories suggest that proper utilization of the operator's sensory capacities under such conditions can improve the operator's performance and reduce the operator's workload. Using a tractor driving simulator, this study investigated whether auditory cues can be used to improve performance of the operator of an agricultural vehicle. Steering of a vehicle was simulated in visual mode (where driving error was shown to the subject using a lightbar) and in auditory mode (where a pair of speakers were used to convey the driving error direction and/or magnitude). A secondary task was also introduced in order to simulate the monitoring of an attached machine. This task included monitoring of two identical displays, which were placed behind the simulator, and responding to them, when needed, using a joystick. This task was also implemented in auditory mode (in which a beep signaled the subject to push the proper button when a response was needed) and in visual mode (in which there was no beep and visual, monitoring of the displays was necessary). Two levels of difficulty of the monitoring task were used. Deviation of the simulated vehicle from a desired straight line was used as the measure of performance in the steering task, and reaction time to the displays was used as the measure of performance in the monitoring task. Results of the experiments showed that steering performance was significantly better when steering was a visual task (driving errors were 40% to 60% of the driving errors in auditory mode), although subjective evaluations showed that auditory steering could be easier, depending on the implementation. Performance in the monitoring task was significantly better for auditory implementation (reaction time was approximately 6 times shorter), and this result was strongly supported by subjective ratings. The majority of the

  6. Eye Safe, Visible Wavelength Lidar Systems: Design and Operational Advances, Results and Potential

    NASA Technical Reports Server (NTRS)

    Spinhirne, James; Welton, Ellsworth J.; Berkoff, Timothy; Campbell, James

    2007-01-01

    In the early nineties the first of the eye safe visible wavelength lidar systems known now as Micro Pulse Lidar (MPL) became operational. The important advance of the design was a system that, unlike most existing lidar, operated at eye safe energy densities and could thus operate unattended for full time monitoring. Since that time there have been many dozens of these systems produced and applied for full time profiling of atmospheric cloud and aerosol structure. There is currently an observational network of MPL sites to support global climate research. In thc course of application of these instruments there have been significant improvements in the, design and performance of the systems. In the last half decade particularly there has been significant application and technical development of MPL systems. In this paper we review progress. The current MPL systems in use are all single wavelength systems designed for cloud and aerosol applications. For the cloud and aerosol applications, both lidar depolarization and multi wavelength measurements have significant applications. These can be accomplished with the MPL, approach. The main current challenge for the lidar network activity are in the area of the reliability, repeatability and efficiency of data processing. The network makes use of internet data downloads and automated processing. The heights of all cloud and aerosol layers are needed. The recent emphasis has been in operationally deriving aerosol extinction cross section. Future emphasis will include adding cirrus optical parameters. For operational effectiveness, improvements to simplify routine data signal calibration are being researched. Overall the MPL systems have proven very effective. A large data base of results from globally distributed sites can be easily accessed through the internet. Applications have included atmospheric model development. Validation of current global satellite observations of aerosol and clouds, including now orbital lidar

  7. Initial operating results of coal-fired steam generators converted to 100% refuse-derived fuel

    SciTech Connect

    Barsin, J.A. ); Graika, P.K. ); Gonyeau, J.A. ); Bloomer, T.M. )

    1988-01-01

    The conversion of Northern States Power Company's (NSP) Red Wing and Wilmarth steam generators to fire refuse-derived fuel (RDF) is discussed. The use of the existing plant with the necessary modifications to the boilers has allowed NSP to effectively incinerate the fuel as required by Washington and Ramsey Counties. This paper covers the six-month start-up of Red Wing No. 1, commencing in May 1987, and the operating results since the plant went commercial in July 1987.

  8. [RESULTS OF RESTORATIVE OPERATIONS USING MODIFIED METHOD OF FORMATION OF TEMPORARY LOOP INTESTINAL STOMAS].

    PubMed

    Pomazkin, V I

    2015-01-01

    The article estimated the results of excision of temporary loop colo- and ileostomas using method of their formation with erfixation of parietal peritoneum to aponeurosis of abdominal external oblique muscle in 18 patients. The authors concluded that the formation of temporary loop stoma with fixation of parietal peritoneum to aponeurosis had many advantages and could ter mprve he rsuls of the resoraive operation. PMID:26234072

  9. Preliminary Operational Results of the TDRSS Onboard Navigation System (TONS) for the Terra Mission

    NASA Technical Reports Server (NTRS)

    Gramling, Cheryl; Lorah, John; Santoro, Ernest; Work, Kevin; Chambers, Robert; Bauer, Frank H. (Technical Monitor)

    2000-01-01

    The Earth Observing System Terra spacecraft was launched on December 18, 1999, to provide data for the characterization of the terrestrial and oceanic surfaces, clouds, radiation, aerosols, and radiative balance. The Tracking and Data Relay Satellite System (TDRSS) Onboard Navigation System (ONS) (TONS) flying on Terra provides the spacecraft with an operational real-time navigation solution. TONS is a passive system that makes judicious use of Terra's communication and computer subsystems. An objective of the ONS developed by NASA's Goddard Space Flight Center (GSFC) Guidance, Navigation and Control Center is to provide autonomous navigation with minimal power, weight, and volume impact on the user spacecraft. TONS relies on extracting tracking measurements onboard from a TDRSS forward-link communication signal and processing these measurements in an onboard extended Kalman filter to estimate Terra's current state. Terra is the first NASA low Earth orbiting mission to fly autonomous navigation which produces accurate results. The science orbital accuracy requirements for Terra are 150 meters (m) (3sigma) per axis with a goal of 5m (1 sigma) RSS which TONS is expected to meet. The TONS solutions are telemetered in real-time to the mission scientists along with their science data for immediate processing. Once set in the operational mode, TONS eliminates the need for ground orbit determination and allows for a smooth flow from the spacecraft telemetry to planning products for the mission team. This paper will present the preliminary results of the operational TONS solution available from Terra.

  10. Experimental design, operation, and results of a 4 kW high temperature steam electrolysis experiment

    NASA Astrophysics Data System (ADS)

    Zhang, Xiaoyu; O'Brien, James E.; Tao, Greg; Zhou, Can; Housley, Gregory K.

    2015-11-01

    High temperature steam electrolysis (HTSE) is a promising technology for large-scale hydrogen production. However, research on HTSE performance above the kW level is limited. This paper presents the results of 4 kW HTSE long-term test completed in a multi-kW test facility recently developed at the Idaho National Laboratory (INL). The 4 kW HTSE unit consisted of two solid oxide electrolysis stacks electrically connected in parallel, each of which included 40 electrode-supported planar cells. A current density of 0.41 A cm-2 was used for the long-term operating at a constant current mode, resulting in a theoretical hydrogen production rate about 23 slpm. A demonstration of 830 h stable operation was achieved with a degradation rate of 3.1% per 1000 h. The paper also includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. This successful demonstration of multi-kW scale HTSE unit will help to advance the technology toward near-term commercialization.

  11. Results of the NASA Kennedy Space Center 50-MHz Doppler Radar Wind Profiler Operational Acceptance Test

    NASA Technical Reports Server (NTRS)

    Barbre', Robert E., Jr.; Decker, Ryan K.; Leahy, Frank B.; Huddleston, Lisa

    2016-01-01

    This paper presents results of the new Kennedy Space Center (KSC) 50-MHz Doppler Radar Wind Profiler (DRWP) Operational Acceptance Test (OAT). The goal of the OAT was to verify the data quality of the new DRWP against the performance of the previous DRWP in order to use wind data derived by the new DRWP for space launch vehicle operations support at the Eastern Range. The previous DRWP was used as a situational awareness asset for mission operations to identify rapid changes in the wind environment that weather balloons cannot depict. The Marshall Space Flight Center's Natural Environments Branch assessed data from the new DRWP collected during Jan-Feb 2015 against a specified set of test criteria. Data examination verified that the DRWP provides complete profiles every five minutes from 1.8-19.5 km in vertical increments of 150 m. Analysis of 49 concurrent DRWP and balloon profiles presented root mean square wind component differences around 2.0 m/s. Evaluation of the DRWP's coherence between five-minute wind pairs found the effective vertical resolution to be Nyquist-limited at 300 m for both wind components. In addition, the sensitivity to rejecting data that do not have adequate signal was quantified. This paper documents the data, quality control procedures, methodology, and results of each analysis.

  12. Electron cooling of 8-GeV antiprotons at Fermilab's Recycler: Results and operational implications

    SciTech Connect

    Prost, L.R.; Broemmelsiek, D.; Burov, Alexey V.; Carlson, K.; Gattuso, C.; Hu, M.; Kroc, T.; Leibfritz, J.; Nagaitsev, S.; Pruss, S.; Saewert, G.; Schmidt, C.W.; Shemyakin, A.; Sutherland, M.; Tupikov, V.; Warner, A.; /Fermilab

    2006-05-01

    Electron cooling of 8 GeV antiprotons at Fermilab's Recycler storage ring is now routinely used in the collider operation. It requires a 0.1-0.5 A, 4.3 MeV dc electron beam and is designed to increase the longitudinal phase-space density of the circulating antiproton beam. This paper briefly describes the characteristics of the electron beam that were achieved to successfully cool antiprotons. Then, results from various cooling force measurements along with comparison to a nonmagnetized model are presented. Finally, operational aspects of the implementation of electron cooling at the Recycler are discussed, such as adjustments to the cooling rate and the influence of the electron beam on the antiproton beam lifetime.

  13. First Operating Results of a Dynamic Gas Bearing Turbine in AN Industrial Hydrogen Liquefier

    NASA Astrophysics Data System (ADS)

    Bischoff, S.; Decker, L.

    2010-04-01

    Hydrogen has been brought into focus of industry and public since fossil fuels are depleting and costs are increasing dramatically. Beside these issues new high-tech processes in the industry are in need for hydrogen at ultra pure quality. To achieve these requirements and for efficient transportation, hydrogen is liquefied in industrial plants. Linde Gas has commissioned a new 5.5 TPD Hydrogen liquefier in Leuna, Germany, which has been engineered and supplied by Linde Kryotechnik. One of the four expansion turbines installed in the liquefaction process is equipped with dynamic gas bearings. Several design features and operational characteristics of this application will be discussed. The presentation will include results of efficiency and operational reliability that have been determined from performance tests. The advantages of the Linde dynamic gas bearing turbine for future use in hydrogen liquefaction plants will be shown.

  14. Flight results from a study of aided inertial navigation applied to landing operations

    NASA Technical Reports Server (NTRS)

    Mcgee, L. A.; Smith, G. L.; Hegarty, D. M.; Carson, T. M.; Merrick, R. B.; Schmidt, S. F.; Conrad, B.

    1973-01-01

    An evaluation is presented of the approach and landing performance of a Kalman filter aided inertial navigation system using flight data obtained from a series of approaches and landings of the CV-340 aircraft at an instrumented test area. A description of the flight test is given, in which data recorded included: (1) accelerometer signals from the platform of an INS; (2) three ranges from the Ames-Cubic Precision Ranging System; and (3) radar and barometric altimeter signals. The method of system evaluation employed was postflight processing of the recorded data using a Kalman filter which was designed for use on the XDS920 computer onboard the CV-340 aircraft. Results shown include comparisons between the trajectories as estimated by the Kalman filter aided system and as determined from cinetheodolite data. Data start initialization of the Kalman filter, operation at a practical data rate, postflight modeling of sensor errors and operation under the adverse condition of bad data are illustrated.

  15. On the use of planning models in the operating theatre: results of a survey in Flanders.

    PubMed

    Cardoen, Brecht; Demeulemeester, Erik; Van der Hoeven, Jessie

    2010-01-01

    This paper presents an overview of the operating theatre planning and scheduling practice of hospitals in Flanders (Belgium). An electronic survey was sent to 95 hospitals in which surgeries are performed, which eventually resulted in a response set of 52 hospitals (55%). The questionnaire did not only focus on issues related to the elective (inpatient and outpatient) planning and scheduling process, but also questioned how hospitals currently deal with the occurrence of non-elective surgeries (urgencies and emergencies). We indicate what goals health managers try to achieve and how this planning is established. We furthermore pay attention to some possible disruptions to the schedule and the corresponding anticipatory methods. Despite the proliferation of computerized planning and scheduling procedures proposed by the scientific community, the implementation rate of satisfying technological planning or evaluation systems still seems to be low. In order to increase the operating theatre efficiency, a closer cooperation between the academic institutions and the practitioners should be encouraged. PMID:20066673

  16. Results from Vernier Scans in RHIC from 2001/02 Au-Au and pp Operation

    NASA Astrophysics Data System (ADS)

    Drees, Angelika; Xu, Zhangbu; Zhang, Haibin

    2002-10-01

    A series of Vernier Scans (or Van-der-Meer Scans) has been performed during the Au-Au run as well as the pp run at a beam energy of 100 GeV in RHIC during the 2001/02 operation period. During a scan one beam is swept across the other in the two transverse planes while collision rates are monitored as a function of beam displacement. Scans were done at various settings of beta* and various IRs. Maximum collision rate and transverse beam profiles are derived from a Gauss fit to the scan data. This report explains the method and summarizes the data taken during this operation period. first results from the fits are shown and compared to prediction and earlier runs.

  17. FIRST OPERATING RESULTS OF A DYNAMIC GAS BEARING TURBINE IN AN INDUSTRIAL HYDROGEN LIQUEFIER

    SciTech Connect

    Bischoff, S.; Decker, L.

    2010-04-09

    Hydrogen has been brought into focus of industry and public since fossil fuels are depleting and costs are increasing dramatically. Beside these issues new high-tech processes in the industry are in need for hydrogen at ultra pure quality. To achieve these requirements and for efficient transportation, hydrogen is liquefied in industrial plants. Linde Gas has commissioned a new 5.5 TPD Hydrogen liquefier in Leuna, Germany, which has been engineered and supplied by Linde Kryotechnik. One of the four expansion turbines installed in the liquefaction process is equipped with dynamic gas bearings. Several design features and operational characteristics of this application will be discussed. The presentation will include results of efficiency and operational reliability that have been determined from performance tests. The advantages of the Linde dynamic gas bearing turbine for future use in hydrogen liquefaction plants will be shown.

  18. Midterm results after arterial switch operation for transposition of the great arteries: a single centre experience

    PubMed Central

    2012-01-01

    Background The arterial switch operation (ASO) has become the surgical approach of choice for d-transposition of the great arteries (d-TGA). There is, however an increased incidence of midterm and longterm adverse sequelae in some survivors. In order to evaluate operative risk and midterm outcome in this population, we reviewed patients who underwent ASO for TGA at our centre. Methods In this retrospective study 52 consecutive patients with TGA who underwent ASO between 04/1991 and 12/1999 were included. To analyze the predictors for mortality and adverse events (coronary stenoses, distortion of the pulmonary arteries, dilatation of the neoaortic root, and aortic regurgitation), a multivariate analysis was performed. The follow-up time was ranged from 1–10 years (mean 5 years, cumulative 260 patient-years). Results All over mortality rate was 15.4% and was only observed in the early postoperative period till 1994. The predictors for poor operative survival were low APGAR-score, older age at surgery, and necessity of associated surgical procedures. Late re-operations were necessary in 6 patients (13.6%) and included a pulmonary artery patch enlargement due to supravalvular stenosis (n = 3), coronary revascularisation due to coronary stenosis in a coronary anatomy type E, aortic valve replacement due to neoaortic valve regurgitation (n = 2), and patch-plasty of a pulmonary vein due to obstruction (n = 1). The dilatation of neoaortic root was not observed in the follow up. Conclusions ASO remains the procedure of choice for TGA with acceptable early and late outcome in terms of overall survival and freedom of reoperation. Although ASO is often complex and may be associated with morbidity, most patients survived without major complications even in a small centre. PMID:22958234

  19. Influence of existing retinal correspondence on the results of squint operations in alternating convergent strabism.

    PubMed

    Zehetmayer, M; Stangler-Zuschrott, E; Schneider, B

    1994-01-01

    In our study we examined the influence of existing retinal correspondence on the result of squint operations for alternating convergent strabism. 157 patients under 10 years of age at the time of their first or only operation were included. They were divided into groups, depending on their age at the onset of squint and subgroups according to their type of retinal correspondence. The development of distance and near deviation was investigated separately. Covariance analysis demonstrated that the preoperative sensorial state is a predictor for the motor outcome of surgery with regard to postoperative distance deviation. Statistically we found at least noticeable results (p < 0.15) in all groups of patients--for acquired esotropia a significant result (p < 0.01). With regard to the postoperative near deviation we found a significant influence of the preoperative sensorial state only in the group of patients with a late onset of squint (p = 0.05). For patients with an earlier onset (before the 30th month) of strabismus, the preoperative angle of near deviation proved to have a significant impact on the postoperative development of near deviation (p < 0.05). Sensorio-motorial adaptational phenomena in esotropia are presumed to be the major cause for this difference. PMID:7781480

  20. Design, construction, and operational results of an 800-A, 10-kV hot deck amplifier

    SciTech Connect

    Reass, W.A.

    1984-06-01

    This paper describes the electrical design, implementation, and operational results of a high fidelity (feedback regulated) 800 A, 10-kV hard tube, hot deck amplifier. The amplifier can produce any linear waveform to 800-A for 30 ms and beyond (depending on main energy storage). The present use is to drive the vertical field (VF) control windings on ZT-40M, a toroidal reversed field pinch plasma physics experiment. Although our application requires only 10 kV (8 MW) of switching, anode voltage may be as high as 40 kV (32 MW).

  1. The Dome C Gattini sky brightness cameras: results from the first year of operation

    NASA Astrophysics Data System (ADS)

    Moore, A. M.; Leslie, T.; Ashley, M. C. B.; Aristidi, E.; Bedding, T.; Briguglio, R.; Busso, M.; Candidi, M.; Cutispoto, G.; Distefano, E.; Everett, J.; Kenyon, S.; Lawrence, J.; Le Roux, B.; Luong-van, D.; Phillips, A.; Ragazzoni, R.; Sabbatini, L.; Salinari, P.; Stello, D.; Storey, J. W. V.; Taylor, M.; Tosti, G.; Travouillon, T.

    The Gattini-DomeC project, part of the IRAIT site testing campaign and ongoing since January 2006, consists of two cameras for the measurement of optical sky brightness, large area cloud cover, and auroral detection above the DomeC site, home of the French-Italian Concordia station. The cameras are transit in nature and are virtually identical except for the nature of the lenses. The cameras have operated throughout the past two Antarctic winter seasons and here we present the results obtained from the 2006 winter-time dataset of the wide field “All-sky camera".

  2. Antihepatitis C virus status in hepatocellular carcinoma and the influence on clinicopathological findings and operative results.

    PubMed

    Takeda, S; Nagafuchi, Y; Tashiro, H; Abe, Y; Fukushige, H; Komori, H; Okamoto, K; Ohsato, K; Haratake, J

    1992-11-01

    Antihepatitis C virus (HCV) status was investigated in 100 patients undergoing hepatectomy for hepatocellular carcinoma (HCC) between 1980 and 1989. The clinicopathological findings and operative results, in patients with or without HCV marker, were compared retrospectively. The positivity rate of anti-HCV was 51 per cent. In this group there was a higher mean age, fewer symptoms, raised alanine aminotransferase level, higher 15-min indocyanine green clearance rate and earlier tumour stage compared with the anti-HCV negative group. Positive tumour margins and vascular invasion were seen less frequently in the anti-HCV positive group. HCC with HCV marker showed characteristic features of chronic non-A non-B hepatitis and of HCC originating from liver cirrhosis. There was a better cumulative 1-year survival rate for anti-HCV positive patients, but 3- and 5-year survival rates after hepatectomy were similar in both groups. Although HCV-related HCC had typical features of chronic non-A non-B hepatitis and a relatively early stage of tumour, biological features and operative results were similar with or without the HCV marker. PMID:1281733

  3. Planned LMSS propagation experiment using ACTS: Preliminary antenna pointing results during mobile operations

    NASA Technical Reports Server (NTRS)

    Rowland, John R.; Goldhirsh, Julius; Vogel, Wolfhard J.; Torrence, Geoffrey W.

    1991-01-01

    An overview and a status description of the planned LMSS mobile K band experiment with ACTS is presented. As a precursor to the ACTS mobile measurements at 20.185 GHz, measurements at 19.77 GHz employing the Olympus satellite were originally planned. However, because of the demise of Olympus in June of 1991, the efforts described here are focused towards the ACTS measurements. In particular, we describe the design and testing results of a gyro controlled mobile-antenna pointing system. Preliminary pointing measurements during mobile operations indicate that the present system is suitable for measurements employing a 15 cm aperture (beamwidth at approximately 7 deg) receiving antenna operating with ACTS in the high gain transponder mode. This should enable measurements with pattern losses smaller than plus or minus 1 dB over more than 95 percent of the driving distance. Measurements with the present mount system employing a 60 cm aperture (beamwidth at approximately 1.7 deg) results in pattern losses smaller than plus or minus 3 dB for 70 percent of the driving distance. Acceptable propagation measurements may still be made with this system by employing developed software to flag out bad data points due to extreme pointing errors. The receiver system including associated computer control software has been designed and assembled. Plans are underway to integrate the antenna mount with the receiver on the University of Texas mobile receiving van and repeat the pointing tests on highways employing a recently designed radome system.

  4. Evaluating the Potential of NASA's Earth Science Research Results for Improving Future Operational Systems

    NASA Astrophysics Data System (ADS)

    Frederick, M. E.; Cox, E. L.; Friedl, L. A.

    2006-12-01

    NASA's Earth Science Theme is charged with implementing NASA Strategic Goal 3A to "study Earth from space to advance scientific understanding and meet societal needs." In the course of meeting this objective, NASA produces research results, such as scientific observatories, research models, advanced sensor and space system technology, data active archives and interoperability technology, high performance computing systems, and knowledge products. These research results have the potential to serve society beyond their intended purpose of answering pressing Earth system science questions. NASA's Applied Sciences Program systematically evaluates the potential of the portfolio of research results to serve society by conducting projects in partnership with regional/national scale operational partners with the statutory responsibility to inform decision makers. These projects address NASA's National Applications and the societal benefit areas under the IEOS and GEOSS. Prototyping methods are used in two ways in NASA's Applied Sciences Program. The first is part of the National Applications program element, referred to as Integrated Systems Solutions (ISS) projects. The approach for these projects is to use high fidelity prototypes to benchmark the assimilation of NASA research results into our partners' decision support systems. The outcome from ISS projects is a prototype system that has been rigorously tested with the partner to understand the scientific uncertainty and improved value of their modified system. In many cases, these completed prototypes are adopted or adapted for use by the operational partners. The second falls under the Crosscutting Solutions program element, referred to as Rapid Prototyping (RP) experiments. The approach for RP experiments is to use low fidelity prototypes that are low cost and quickly produced to evaluate the potential of the breadth of NASA research results to serve society. The outcome from the set of RP experiments is an

  5. Seroprevalence of Dengue Fever in US Army Special Operations Forces: Initial Results and the Way Ahead.

    PubMed

    Caci, Jennifer B; Blaylock, Jason M; De La Barrera, Rafael; Griggs, April N; Lin, Leyi; Jarman, Richard G; Thomas, Stephen J; Lyons, Arthur G

    2014-01-01

    The endemicity of dengue fever (DF) and, consequently, sequelae of DF are increasing worldwide. The increases are largely a result of widespread international travel and the increased range of the mosquito vectors. US Army Special Operations Command (USASOC) personnel are at an increased risk of exposure to dengue based on their frequent deployments to and presence in dengue endemic areas worldwide. Repeated deployments to different endemic areas can increase the risk for developing the more serious sequelae of dengue: dengue hemorrhagic fever (DHF) and dengue shock syndrome (DSS). Information about the seroprevalence rate of dengue in USASOC personnel, in particular, is lacking and is critical to assessing the risk, tailoring preventive medicine countermeasures, leveraging field diagnostics, and maintaining mission capability. In the first part of a two-part project to assess baseline seroprevalence in USASOC units, a random, unit-stratified sample of 500 anonymous serum specimens from personnel assigned to the highest-risk units in USASOC were screened for dengue using a microneutralization assay. Of the 500 specimens screened, 56 (11.2%) of 500 had neutralizing titers (NT) (MN₅₀≥10) against at least one DENV serotype. Subsequent sample titration resulted in 48 (85.7%) of 56 of the samples with NT (MN₅₀≥10) against at least one dengue serotype for an overall dengue exposure rate of 9.6% (48 of 500). The second part of the ongoing project, started in 2012, was a multicenter, serosurveillance project using predeployment and postdeployment sera collected from USASOC personnel deployed to South and Central America, Africa, and Southeast Asia. Preliminary results show a 13.2% (55 of 414) seropositivity rate. The significance of these findings as they relate to personal risk and operational impact is discussed. PMID:25344719

  6. Operation and results of the prototype KM3NeT detection unit

    NASA Astrophysics Data System (ADS)

    Biagi, Simone

    2016-07-01

    KM3NeT will be a km3-scale neutrino telescope in the Mediterranean Sea. The detector will consist of blocks of about one hundred detection units. Each detection unit will host 18 digital optical modules, connected along a 700 m-long vertical structure. Electro-optical cables allow for data transmission and power supply to the optical modules. The optical module comprises 31 photomultiplier tubes of 3'', instruments to monitor environmental variables and electronic boards to communicate onshore and operate the photomultipliers. A prototype detection unit has been deployed in May 2014 at the KM3NeT-It installation site 80 km SE offshore of Capo Passero, Sicily. This prototype allowed to test the deployment procedures, the mechanics and the electronic of the apparatus, the data taking and analysis procedures. A general description of the detector and some results of the prototype are presented. The first detection unit of the KM3NeT neutrino telescope will be deployed and become operative by the end of 2015.

  7. Operative results of keyhole supracerebellar-infratentorial approach to the pineal region.

    PubMed

    Bonney, Phillip A; Boettcher, Lillian B; Cheema, Ahmed A; Maurer, Adrian J; Sughrue, Michael E

    2015-07-01

    The supracerebellar-infratentorial approach to the pineal region is typically accomplished with a craniotomy that extends to at least the rim of the foramen magnum. Minimally invasive techniques that limit the inferior extent of the craniotomy have been described for this approach but, to our knowledge, no operative results have been published demonstrating the feasibility and safety of such techniques. We present a series of patients who underwent surgical resection of pineal region lesions using the minimally invasive method at our institution. Clinical, radiologic, and operative data were prospectively collected on patients treated for lesions of the pineal region by the senior author from January 2012 to July 2014. Seven patients were identified. The sitting position was employed in each patient. Keyhole craniotomies were limited to a maximum diameter of 2.5 cm. Adequate working corridors were attained, and in no patient was resection limited by the exposure. No neurological or systemic complications were seen in the perioperative and early follow-up periods. In this feasibility study, we demonstrate that it is not necessary to extend a craniotomy inferiorly to the rim of the foramen magnum in order to gain access to the pineal region via relaxation of the cerebellum. The same surgical goals can be safely accomplished with a smaller craniotomy. PMID:25913279

  8. Overview and Results of ISS Space Medicine Operations Team (SMOT) Activities

    NASA Technical Reports Server (NTRS)

    Johnson, H. Magee; Sargsyan, Ashot E.; Armstrong, Cheryl; McDonald, P. Vernon; Duncan, James M.; Bogomolov, V. V.

    2007-01-01

    The Space Medicine Operations Team (SMOT) was created to integrate International Space Station (ISS) Medical Operations, promote awareness of all Partners, provide emergency response capability and management, provide operational input from all Partners for medically relevant concerns, and provide a source of medical input to ISS Mission Management. The viewgraph presentation provides an overview of educational objectives, purpose, operations, products, statistics, and its use in off-nominal situations.

  9. Abstract Model of the SATS Concept of Operations: Initial Results and Recommendations

    NASA Technical Reports Server (NTRS)

    Dowek, Gilles; Munoz, Cesar; Carreno, Victor A.

    2004-01-01

    An abstract mathematical model of the concept of operations for the Small Aircraft Transportation System (SATS) is presented. The Concept of Operations consist of several procedures that describe nominal operations for SATS, Several safety properties of the system are proven using formal techniques. The final goal of the verification effort is to show that under nominal operations, aircraft are safely separated. The abstract model was written and formally verified in the Prototype Verification System (PVS).

  10. Overview of JT-60U results towards the establishment of advanced tokamak operation

    NASA Astrophysics Data System (ADS)

    Oyama, N.; JT-60 Team

    2009-10-01

    Recent JT-60U experimental results towards the establishment of advanced tokamak (AT) operation are reviewed. We focused on the further expansion of the operational regime of AT plasmas towards higher βN regime with wall stabilization. After the installation of ferritic steel tiles in 2005, the high power heating in a large plasma cross-section in which the wall stabilization is expected has been possible. In 2007, the modification of power supply of NBIs improved the flexibility of the heating profile in long-pulse plasmas. The investigation of key physics issues for the establishment of steady-state AT operation is also in progress using new diagnostics and improved heating systems. In weak magnetic shear plasma, high βN ~ 3 exceeding the ideal MHD limit without a conducting wall ( \\beta_N^{{\\scriptsize{\\mbox{no-wall}}}} ) is sustained for ~5 s (~3τR) with RWM stabilization by a toroidal rotation at the q = 2 surface. External current drivers of negative-ion based NB and lower-hybrid waves together with a large bootstrap current fraction (fBS) of 0.5 can sustain the whole plasma current of 0.8 MA for 2 s (1.5τR). In reversed magnetic shear plasma, high βN ~ 2.7 (βp ~ 2.3) exceeding \\beta_N^{{\\scriptsize{\\mbox{no-wall}}}} with qmin ~ 2.4 (q95 ~ 5.3), HH98(y,2) ~ 1.7 and fBS ~ 0.9 is obtained with wall stabilization. These plasma parameters almost satisfy the requirement of ITER steady-state scenario. In long-pulse plasmas with positive magnetic shear, a high βNHH98(y,2) of 2.6 with βN ~ 2.6 and HH98(y,2) ~ 1 is sustained for 25 s, significantly longer than the current diffusion time (~14τR) without neoclassical tearing modes (NTMs). A high G-factor, \\beta_NH_{89P}/q_{95}^{2} (a major of fusion gain), of 0.54 and a large fBS > 0.43 are suitable for ITER hybrid operation scenario. Based on the plasma for ITER hybrid operation scenario, the high βN of 2.1 with good thermal plasma confinement of HH98(y,2) > 0.85 is sustained for longer than 12 s at

  11. Smart garments for emergency operators: results of laboratory and field tests.

    PubMed

    Curone, Davide; Dudnik, Gabriela; Loriga, Giannicola; Magenes, Giovanni; Secco, Emanuele Lindo; Tognetti, Alessandro; Bonfiglio, Annalisa

    2008-01-01

    The first generation of ProeTEX prototypes has been completed at the end of August 2007. In the following period two main activities have involved the project partners. On one hand new technologies (in terms of sensors and devices) to be integrated in the next releases of prototypes have been developed; on the other hand intensive test sessions on the first prototype (both in laboratory conditions and simulating real operative scenarios) have been carried out. This paper is mainly focused on this second facet. Great efforts have been dedicated to the trials for different reasons: firstly to investigate the appropriateness and efficiency of the system in normal and harsh conditions; secondly to obtain useful indications regarding usability and efficacy by the end-users involved in the project. The results of the trials have been used to define the specifications of the second generation of prototypes, that will be released within the end of 2008. PMID:19162701

  12. Past operations, results, and prospects of future petroleum explorations in the SE Pannonian basin

    SciTech Connect

    Sarkovic, M.; Stankovic, S. )

    1991-08-01

    The long history of petroleum operations in the southeastern area of the Pannonian basin (eastern Yugoslavia) relates to successful explorations using state-of-art tools in geology, geophysics, and geochemistry, as well as in deep drilling. The paper will discuss chronologically past explorations and problems encountered in its specific stages. A comprehensive petroleum geological overview will highlight the most important features of the 30,000-km{sup 2} exploration area, including issues such as oil and gas origin, occurrence of source, reservoir, and cap rocks, hydrocarbon migration and accumulation etc. Particular attention will be devoted to the description of the applied exploration techniques and results obtained on this very interesting hydrocarbon-bearing area. Due space will be given to the application of the recent developments for assessing the potential of the deep buried, comparatively unknown targets situated in extremely complex environments under adverse temperature and pressure conditions.

  13. Defining Learning Space in a Serious Game in Terms of Operative and Resultant Actions

    NASA Technical Reports Server (NTRS)

    Martin, Michael W.; Shen, Yuzhong

    2012-01-01

    This paper explores the distinction between operative and resultant actions in games, and proposes that the learning space created by a serious game is a function of these actions. Further, it suggests a possible relationship between these actions and the forms of cognitive load imposed upon the game player. Association of specific types of cognitive load with respective forms of actions in game mechanics also presents some heuristics for integrating learning content into serious games. Research indicates that different balances of these types of actions are more suitable for novice or experienced learners. By examining these relationships, we can develop a few basic principles of game design which have an increased potential to promote positive learning outcomes.

  14. TOPEX/POSEIDON operational orbit determination results using global positioning satellites

    NASA Technical Reports Server (NTRS)

    Guinn, J.; Jee, J.; Wolff, P.; Lagattuta, F.; Drain, T.; Sierra, V.

    1994-01-01

    Results of operational orbit determination, performed as part of the TOPEX/POSEIDON (T/P) Global Positioning System (GPS) demonstration experiment, are presented in this article. Elements of this experiment include the GPS satellite constellation, the GPS demonstration receiver on board T/P, six ground GPS receivers, the GPS Data Handling Facility, and the GPS Data Processing Facility (GDPF). Carrier phase and P-code pseudorange measurements from up to 24 GPS satellites to the seven GPS receivers are processed simultaneously with the GDPF software MIRAGE to produce orbit solutions of T/P and the GPS satellites. Daily solutions yield subdecimeter radial accuracies compared to other GPS, LASER, and DORIS precision orbit solutions.

  15. An operational food warning system in Andalucía (Spain): Presentation and first successfully results

    NASA Astrophysics Data System (ADS)

    Versini, Pierre-Antoine; Corral, Carles; Sempere-Torres, Daniel; Santiago-Gahette, Antonio

    2010-05-01

    The Guadalhorce basin (3200 km2, 130000 inhabitants) is located in Andalucía (South of Spain). Historically the river represents an important risk for the city of Malaga and periodically causes floods along its course. In 2008 the regional government implemented an operational flood warning system with the aim of minimising risk to people, economic activity, and guiding water resources management. The system is oriented to provide distributed warnings based on surface rainfall accumulations and runoff forecasts (at 1 km resolution). These risk warnings are related to hazard probability expressed in terms of return periods. Rainfall accumulation maps are generated according to the following two alternatives: (1) interpolation of the measurements of a network of 40 rain gauges covering the basin, and (2) measurements of the Mijas C-band radar located at 1173 m and covering the whole basin. Radar data are processed according to a complete chain of algorithms including ground clutter elimination, rainfall type classification (convective/stratiform) and correction with a vertical profile of reflectivity. Runoff forecasts are computed with a grid-based rainfall-runoff model incorporating the SCS equations at cell scale. The routing is done with a linear diffusive wave unit hydrograph, separating the hillslope and river-channelled process. Because of the miss of the lack of hydrological records, this model was calibrated a priori on a large part of the basin area. After presenting in details the operational system, it will be illustrated through a concrete example. It has successfully performed during a recent storm (7 January 2010). During this event -the most important since the system works- over 50 mm of rainfall dropped in few hours around Malaga, which resulted in flooding of parts of the city and road submersions. First results show how the warning system performed well and was able to forecast the location and timing of flooded areas.

  16. [Total elbow arthroplasty. Indications, operative technique and results after implantation of an Acclaim elbow prosthesis].

    PubMed

    Lerch, K; Tingart, M; Trail, I; Grifka, J

    2003-08-01

    Total elbow arthroplasty has become a reliable treatment option for patients with rheumatoid arthritis as well as primary or posttraumatic arthrosis. The aim of this study is to present the indications, operative technique and results for the implantation of an Acclaim elbow prosthesis. Case reports are given to demonstrate the indications for prosthesis implantation. Furthermore, the follow-up results are reported for 65 patients after implantation of an Acclaim prosthesis. Pre- and postoperative pain were evaluated using the visual analogue scale. The pain level decreased from 8.0 to 2.3 postoperatively. After implantation of an elbow prosthesis, there was a significant improvement in the range of motion. The mean flexion increased from 103 degrees preoperatively to 140 degrees postoperatively. An increase of 10 degrees was found for both supination and pronation. Complications included temporary ulnary nerve irritation in seven patients, intraoperative fractures in four cases and postoperative elbow dislocation in one case. In conclusion, total elbow arthroplasty results in a reduction of pain and an improvement in elbow movement. However, selection of the right patient is important. Patients are advised not to lift heavy objects or to perform hard physical work. If patients' compliance can not be ensured preoperatively, no total elbow arthroplasty should be performed. PMID:12955197

  17. Realizing actual feedback control of complex network

    NASA Astrophysics Data System (ADS)

    Tu, Chengyi; Cheng, Yuhua

    2014-06-01

    In this paper, we present the concept of feedbackability and how to identify the Minimum Feedbackability Set of an arbitrary complex directed network. Furthermore, we design an estimator and a feedback controller accessing one MFS to realize actual feedback control, i.e. control the system to our desired state according to the estimated system internal state from the output of estimator. Last but not least, we perform numerical simulations of a small linear time-invariant dynamics network and a real simple food network to verify the theoretical results. The framework presented here could make an arbitrary complex directed network realize actual feedback control and deepen our understanding of complex systems.

  18. Designing and Evaluating Classroom Activities Using Remotely Operated Microbeam Instruments: Some Preliminary Results

    NASA Astrophysics Data System (ADS)

    Ryan, J. G.

    2006-12-01

    Using analytical instruments in undergraduate courses is a longstanding method for exposing students to aspects of the research process. A range of instruments (XRD, AA/ICP-OES, IC, ICP-MS; MCS, GPR etc.) have been used in geoscience courses, often with the ancillary outcome of facilitating undergraduate research projects. These activities generally involve instruments available in-house; are usually restricted to "workhorse" instruments that can tolerate use by inexperienced student users; and are focused on comparatively basic analytical tools, as the output data are often more amenable to course content and direction, but also because such tools are viewed as more appropriate to the undergraduate experience. Despite abundant research uses in the geosciences, microbeam technologies (i.e., Scanning Electron Microscope (SEM) and Electron Microprobe (EPMA)) have not been as heavily utilized in the classroom, due to the higher cost of these instruments and the relative delicacy of the hardware, which can involve multiple integrated spectrometers and imaging systems. SEM has been used on occasion as a classroom tool, at times as a lower cost stand-in for EMPA (i.e., Beane 2004), and for its high-resolution imaging capabilities. Remote instrument operation (Pratap et al. 2004) offers a means to bring advanced microbeam instruments into the classroom. We are using the remotely operable SEM and EPMA instruments at the Florida Center for Analytical Electron Microscopy (FCAEM, at FIU in Miami, FL) at the University of South Florida in Tampa, FL in introductory-level and upper level courses. Students receive instruction in microbeam analysis and the specifics of the instrument they are to use (SEM or EPMA). Instrument operation sessions occur in class, examining samples prepared by student teams as part of class projects. Assessment of effectiveness includes student impression surveys, and content-specific testing related to the activities. Early results indicate student

  19. [Radiosurgery in trigeminal neuralgia: long-term results and influence of operative nuances].

    PubMed

    Regis, J; Arkha, Y; Yomo, S; Murata, N; Roussel, P; Donnet, A; Peragut, J-C

    2009-04-01

    Stereotactic radiosurgery is an alternative to conventional surgery for the treatment of trigeminal neuralgia. To better define the safety of radiosurgery and optimal technical choices, we reviewed our patient records and the literature. A total of 334 patients presenting with trigeminal neuralgia were treated between December 1992 and September 2005. A minimum of 1 year of follow-up was available for 262 patients. The mean age was 68 years (range: 30-90); 128 patients were male and 134 female. A neurovascular conflict was clearly visualized on MRI in 167 patients. Twenty-one had a past history of multiple sclerosis and 110 had already received conventional surgical treatment for trigeminal neuralgia. The intervention consisted of gamma knife radiosurgery (GKS) to the retrogasserian cisternal portion of the Vth cranial nerve. The median maximal dose used was 85Gy (range: 70-90). Actuarial curves show a plateau at 5 years for both the risk of hypoesthesia and recurrence. At 5 years, 58% of the patients remain pain-free and 83% have no trigeminal nerve disturbance. The median delay for pain cessation was 15 days. The initial pain-relief rate was 89%. None of the complications reported for the other techniques were observed. Patient selection (typical versus atypical, age, past surgery, multiple sclerosis) and details of operative technique (maximum dose, volume of nerve treated, target location, etc.) had a major influence on the probability of pain relief and toxicity risk. The details of operative technique are turning out to have a major influence on the clinical results. In our experience, high-dose (80-90Gy) retrogasserian (7-8mm from the brainstem) GKS provides the patient with a better chance of long-term pain relief and a lower risk of trigeminal nerve functional disturbance. GKS applied to the cisternal anterior trigeminal nerve using high doses provided safe and effective treatment for trigeminal neuralgia over the long term. PMID:19339026

  20. Evaluation of operational safety at Babcock and Wilcox Plants: Volume 2, Thermal-hydraulic results

    SciTech Connect

    Wheatley, P.D.; Davis, C.B.; Callow, R.A.; Fletcher, C.D.; Dobbe, C.A.; Beelman, R.J.

    1987-11-01

    The Nuclear Regulatory Commission has initiated a research program to develop a methodology to assess the operational performance of Babcock and Wilcox plants and to apply this methodology on a trial basis. The methodology developed for analyzing Babcock and Wilcox plants integrated methods used in both thermal-hydraulics and human factors and compared results with information used in the assessment of risk. The integrated methodology involved an evaluation of a selected plant for each pressurized water reactor vendor during a limited number of transients. A plant was selected to represent each vendor, and three transients were identified for analysis. The plants were Oconee Unit 1 for Babcock and Wilcox, H.B. Robinson Unit 2 for Westinghouse, and Calvert Cliffs Unit 1 for Combustion Engineering. The three transients were a complete loss of all feedwater, a small-break loss-of-coolant accident, and a steam-generator overfill with auxiliary feedwater. Included in the integrated methodology was an assessment of the thermal-hydraulic behavior, including event timing, of the plants during the three transients. Thermal-hydraulic results are presented in this volume (Volume 2) of the report. 26 refs., 30 figs., 7 tabs.

  1. A Minimally Invasive Cox-Maze Procedure: Operative Technique and Results

    PubMed Central

    Lee, Anson M.; Clark, Kal; Bailey, Marci S.; Aziz, Abdulhameed; Schuessler, Richard B.; Damiano, Ralph J.

    2010-01-01

    Summary Objective The Cox-Maze procedure for the surgical treatment of atrial fibrillation traditionally has required a median sternotomy and cardiopulmonary bypass. This study describes a method using ablation technologies to create the full Cox-Maze lesion set through a 5–6 cm right mini-thoracotomy. Methods Twenty-two consecutive patients underwent a Cox-Maze procedure via a right mini-thoracotomy and cardiopulmonary bypass. All patients were followed prospectively with ECG and 24 hour Holter monitoring at 3, 6, and 12 months. The Cox-Maze procedure lesion set was created using bipolar radiofrequency energy and cryothermy. Results There was no operative mortality or major complications. Two patients required a permanent pacemaker. Five patients (23%) had early atrial tachyarrhythmias. At last follow-up (mean 18 ± 12 months), all of the patients (n=22) were free from atrial dysrhythmias. At 3 months (n=19), 84% of patients were off antiarrhythmic drugs. By 6 months (n=18), 94% of patients were free from AF and off antiarrhythmic medications. At 12 months (n=16), 81% of patients were free from AF and off antiarrhythmic drugs and three patients remained on warfarin for a mechanical mitral valve. Conclusions A full Cox-Maze procedure can be performed through a right mini-thoracotomy with outstanding short term results. This less invasive procedure can be offered to patients without compromising efficacy. PMID:21057605

  2. Results of non-operative management of splenic trauma and its complications in children

    PubMed Central

    Oumar, Ndour; Dominique, Forgues; Nikola, Kalfa; Pierre, Guibal Marie; Mamadou, Ndoye; Benoit, Galifer René

    2014-01-01

    Introduction: Non-operative management (NOM) of splenic trauma in children is currently the treatment of choice. Purpose: We report a series of 83 cases in order to compare our results with literature data. Patients and Methods: For this, we conducted a retrospective study of 13 years and collected 83 cases of children with splenic trauma contusion, managed at Lapeyronie Montpellier Hospital in Visceral Pediatric Surgery Department. The studied parameters were age, sex, circumstances, the blood pressure (BP), hematology, imaging, associated injuries, transfusion requirements, treatment, duration of hospital stay, physical activity restriction and evolution. Results: NOM was successful in 98.7% of cases. We noted 4 complications including 3 pseudo aneurysms (PSA) of splenic artery and 1 pseudocyst spleen with a good prognosis. There was no mortality in our series. Conclusion: NOM is the treatment of choice for splenic trauma in children with a success rate of over 90%. Complications are rare and are dominated by the PSA of splenic artery. PMID:25197192

  3. Operations

    ERIC Educational Resources Information Center

    Wilkins, Jesse L. M.; Norton, Anderson; Boyce, Steven J.

    2013-01-01

    Previous research has documented schemes and operations that undergird students' understanding of fractions. This prior research was based, in large part, on small-group teaching experiments. However, written assessments are needed in order for teachers and researchers to assess students' ways of operating on a whole-class scale. In this…

  4. Marine pollution network euromar-mermaid: Results of the experimental operation

    NASA Astrophysics Data System (ADS)

    Knauth, H.-D.; Schroeder, F.; Menzel, R.; Gebhart, E.; Marx, S.; Kohnke, D.; Holzkamm, F.; Nies, H.; Theobald, N.

    1997-09-01

    The need for automated systems to monitor chemical and biochemical variables led to the definition of the EUREKA-EUROMAR project MERMAID. It was realized by several international scientific and industrial partners. Important components were automatic nutrient analyzers and remote-controlled samplers for toxic trace substances in addition to a high-performance data management system with bi-directional telemetry units for remote-controlled network operation. These modules were implemented in the MERMAID network consisting of three sea stations, two of them set up in the Elbe estuary, and one in the Elbe-influenced coastal zone. The latter was at the same time part of the BSH-network. The data were transmitted to shore and processed at GKSS and BSH. While in the preceding project phase the marine pollution network was established and tested, the last MERMAID phase covered its experimental operation. For this purpose, different modules were installed at the three stations. They incorporated meteorological, oceanographic, physical and chemical sensors in addition to automatic analyzers for phosphate, nitrite/nitrate and ammonium as well as specialized samplers for heavy metals and organic micropollutants. Variables were determined directly either continuously by in situ sensors or at variable time intervals by remote-controlled in situ analyzers, or they were determined indirectly by samplers allowing phase-separated multiple sampling with remote or event control of the sampling frequency. In this contribution, the results of nutrient and heavy metal concentration time series measured in 1995 and 1996 are presented together with corresponding meteorological and oceanographic variables. The examples indicate that the transfer of nutrients and contaminants in the estuary and in the coastal zone is strongly influenced by different short- and long-term events, i.e. freshwater discharge rates and wind action. Additionally, in summer, chemical and biological processes

  5. Computer Programs for Library Operations; Results of a Survey Conducted Between Fall 1971 and Spring 1972.

    ERIC Educational Resources Information Center

    Liberman, Eva; And Others

    Many library operations involving large data banks lend themselves readily to computer operation. In setting up library computer programs, in changing or expanding programs, cost in programming and time delays could be substantially reduced if the programmers had access to library computer programs being used by other libraries, providing similar…

  6. Preliminary operational results of the low-temperature solar industrial process heat field tests

    SciTech Connect

    Kutscher, C.F.; Davenport, R.L.

    1980-06-01

    Six solar industrial process heat field tests have been in operation for a year or more - three are hot water systems and three are hot air systems. All are low-temperature projects (process heat at temperatures below 212/sup 0/F). Performance results gathered by each contractor's data acquisition system are presented and project costs and problems encountered are summarized. Flat-plate, evacuated-tube, and line-focus collectors are all represented in the program, with collector array areas ranging from 2500 to 21,000 ft/sup 2/. Collector array efficiencies ranged from 12% to 36% with net system efficiencies from 8% to 33%. Low efficiencies are attributable in some cases to high thermal losses and, for the two projects using air collectors, are due in part to high parasitic power consumption. Problems have included industrial effluents on collectors, glazing and absorber surface failures, excessive thermal losses, freezing and overheating, control problems, and data acquisition system failure. With design and data acquisition costs excluded costs of the projects ranged from $25/ft/sup 2/ to $87/ft/sup 2/ and $499/(MBtu/yr) to $1537/(MBtu/yr).

  7. Operation Ice Bridge overview and results from aircraft laser altimetry (Invited)

    NASA Astrophysics Data System (ADS)

    Krabill, W. B.; Thomas, R. H.; Sonntag, J. G.; Manizade, S.; Fredrick, E.; Yungel, J.

    2009-12-01

    The Arctic Ice Mapping group (Project AIM) at the NASA Goddard Space Flight Center Wallops Flight Facility has been conducting systematic topographic surveys of the Greenland Ice Sheet (GIS) since 1993, using scanning airborne laser altimeters (NASA ATM) combined with Global Positioning System (GPS) technology. In 2009, with ICESat I nearing its operational end, and a replacement not due for at least 5 years, NASA HQ decided to expand the aircraft remote sensing of ice sheets and sea ice to provide the cryospheric science community with interim data sets to monitor changes in Polar Regions. The first of these surveys took place in the spring of 2009, in which numerous segments of ICESat ground tracks in critical areas in Greenland were resurveyed along with many of the previously surveyed aircraft lines. Planned for fall 2009 is a deployment to Punta Arenas, Chile, using NASA’s DC8 long-range aircraft to survey critical sites in Antarctica. Results from these new data sets will be presented. William B. Krabill Project Scientist for Arctic Ice Mapping Cryospheric Sciences Branch, Code 614.1 NASA/GSFC/Wallops Flight Facility, Building N-159, Room E201 Wallops Island, Virginia 23337 USA Tel 757 824 1417 Fax 757 824 1036 e-mail: William.B.Krabill@nasa.gov

  8. A pilot operational flood warning system in Andalusia (Spain): presentation and first results

    NASA Astrophysics Data System (ADS)

    Versini, P.-A.; Berenguer, M.; Corral, C.; Sempere-Torres, D.; Santiago-Gahete, A.

    2011-11-01

    The Guadalhorce Basin is located in Andalusia (South of Spain). Its floods have historically represented a major hazard for the city of Málaga. In 2008 it has been decided to implement a pilot operational flood warning system (GFWS) with the aim of analyzing the capability to minimize the risk to people, and economic activity, as well as for guiding water resources management. The system is oriented to provide distributed warnings based on rainfall accumulations and discharge forecasts. Rainfall accumulation maps are generated according to the interpolation of rain gauge measurements and weather radar rainfall maps whereas discharge forecasts are computed using a distributed rainfall-runoff model. Due to the lack of flow measurements, the model was calibrated a priori in most of the basin area. The performance of the system has been tested on two recent rainfall events which caused many inundations. First results show how the GFWS performed well and was able to forecast the location and timing of flooding. It demonstrates that a simple model and a rough calibration could be enough to issue valuable warnings. Moreover, the European Flood Alert System (EFAS) forecasts have been used to prevent from the flood several days in advance. With low resolution and long anticipation, EFAS appears as a good complement tool to improve flood forecasting and compensate for the short lead times of the GFWS.

  9. Task Shifting Provision of Contraceptive Implants to Community Health Extension Workers: Results of Operations Research in Northern Nigeria

    PubMed Central

    Oguntunde, Olugbenga; Orobaton, Nosa; Otolorin, Emmanuel; Inuwa, Fatima; Alalade, Olubisi; Abegunde, Dele; Danladi, Saba’atu

    2015-01-01

    Background: Contraceptive use remains low in Nigeria, with only 11% of women reporting use of any modern method. Access to long-acting reversible contraceptives (LARCs) is constrained by a severe shortage of human resources. To assess feasibility of task shifting provision of implants, we trained community health extension workers (CHEWs) to insert and remove contraceptive implants in rural communities of Bauchi and Sokoto states in northern Nigeria. Methods: We conducted 2- to 3-week training sessions for 166 selected CHEWs from 82 facilities in Sokoto state (September 2013) and 84 health facilities in Bauchi state (December 2013). To assess feasibility of the task shifting approach, we conducted operations research using a pretest–posttest design using multiple sources of information, including surveys with 151 trained CHEWs (9% were lost to follow-up) and with 150 family planning clients; facility observations using supply checklists (N = 149); direct observation of counseling provided by CHEWs (N = 144) and of their clinical (N = 113) skills; as well as a review of service statistics (N = 151 health facilities). The endline assessment was conducted 6 months after the training in each state. Results: CHEWs inserted a total of 3,588 implants in 151 health facilities over a period of 6 months, generating 10,088 couple-years of protection (CYP). After practicing on anatomic arm models, most CHEWs achieved competency in implant insertions after insertions with 4–5 actual clients. Clinical observations revealed that CHEWs performed implant insertion tasks correctly 90% of the time or more for nearly all checklist items. The amount of information that CHEWs provided clients increased between baseline and endline, and over 95% of surveyed clients reported being satisfied with CHEWs’ services in both surveys. The study found that supervisors not only observed and corrected insertion skills, as needed, during supervisory visits but also encouraged

  10. Indicated and actual mass inventory measurements for an inverted U-tube steam generator

    SciTech Connect

    Loomis, G.G.; Plessinger, M.P.; Boucher, T.J.

    1986-01-01

    Results from an experimental investigation of actual versus indicated secondary liquid level in a steam generator at steaming conditions are presented. The experimental investigation was performed in two different small scale U-tube-in-shell steam generators at typical pressurized water reactor operating conditions (5-7 MPa; saturated) in the Semiscale facility. During steaming conditions, the indicated secondary liquid level was found to vary considerably from the actual ''bottled-up'' liquid level. These difference between indicated and actual liquid level are related to the frictional pressure drop associated with the two-phase steaming condition in the riser. Data from a series of bottle-up experiments (Simultaneously, the primary heat source and secondary feed and steam are terminated) are tabulated and the actual liquid level is correlated to the indicated liquid level.

  11. First results of operational ionospheric dynamics prediction for the Brazilian Space Weather program

    NASA Astrophysics Data System (ADS)

    Petry, Adriano; de Souza, Jonas Rodrigues; de Campos Velho, Haroldo Fraga; Pereira, André Grahl; Bailey, Graham John

    2014-07-01

    It is shown the development and preliminary results of operational ionosphere dynamics prediction system for the Brazilian Space Weather program. The system is based on the Sheffield University Plasmasphere-Ionosphere Model (SUPIM), a physics-based model computer code describing the distribution of ionization within the Earth mid to equatorial latitude ionosphere and plasmasphere, during geomagnetically quiet periods. The model outputs are given in a 2-dimensional plane aligned with Earth magnetic field lines, with fixed magnetic longitude coordinate. The code was adapted to provide the output in geographical coordinates. It was made referring to the Earth’s magnetic field as an eccentric dipole, using the approximation based on International Geomagnetic Reference Field (IGRF-11). During the system operation, several simulation runs are performed at different longitudes. The original code would not be able to run all simulations serially in reasonable time. So, a parallel version for the code was developed for enhancing the performance. After preliminary tests, it was frequently observed code instability, when negative ion temperatures or concentrations prevented the code from continuing its processing. After a detailed analysis, it was verified that most of these problems occurred due to concentration estimation of simulation points located at high altitudes, typically over 4000 km of altitude. In order to force convergence, an artificial exponential decay for ion-neutral collisional frequency was used above mentioned altitudes. This approach shown no significant difference from original code output, but improved substantially the code stability. In order to make operational system even more stable, the initial altitude and initial ion concentration values used on exponential decay equation are changed when convergence is not achieved, within pre-defined values. When all code runs end, the longitude of every point is then compared with its original reference

  12. The relationship between operative and radiographic acetabular component orientation: which factors influence resultant cup orientation?

    PubMed

    Grammatopoulos, G; Pandit, H G; da Assunção, R; McLardy-Smith, P; De Smet, K A; Gill, H S; Murray, D W

    2014-10-01

    There is great variability in acetabular component orientation following hip replacement. The aims of this study were to compare the component orientation at impaction with the orientation measured on post-operative radiographs and identify factors that influence the difference between the two. A total of 67 hip replacements (52 total hip replacements and 15 hip resurfacings) were prospectively studied. Intra-operatively, the orientation of the acetabular component after impaction relative to the operating table was measured using a validated stereo-photogrammetry protocol. Post-operatively, the radiographic orientation was measured; the mean inclination/anteversion was 43° (sd 6°)/ 19° (sd 7°). A simulated radiographic orientation was calculated based on how the orientation would have appeared had an on-table radiograph been taken intra-operatively. The mean difference between radiographic and intra-operative inclination/anteversion was 5° (sd 5°)/ -8° (sd 8°). The mean difference between simulated radiographic and intra-operative inclination/anteversion, which quantifies the effect of the different way acetabular orientation is measured, was 3°/-6° (sd 2°). The mean difference between radiographic and simulated radiographic orientation inclination/anteversion, which is a manifestation of the change in pelvic position between component impaction and radiograph, was 1°/-2° (sd 7°). This study demonstrated that in order to achieve a specific radiographic orientation target, surgeons should implant the acetabular component 5° less inclined and 8° more anteverted than their target. Great variability (2 sd about ± 15°) in the post-operative radiographic cup orientation was seen. The two equally contributing causes for this are variability in the orientation at which the cup is implanted, and the change in pelvic position between impaction and post-operative radiograph. PMID:25274911

  13. Radiation Test Results for a MEMS Microshutter Operating at 60 K

    NASA Technical Reports Server (NTRS)

    Rapchun, David A.; Buchner, Stephen; Moseley, Harvey; Meyer, Stephen E.; Ray, Knute; Tuttle, Jim; Quinn, Ed; Buchanan, Ernie; Bloom, Dave; Hait, Tom; Pearce, Mike; Beamer, A.

    2007-01-01

    MEMS. Knowledge of the above principle has raised the concern at NASA that the MSA might also exhibit degraded performance because, i) each shutter flap is a multilayer structure consisting of metallic and insulating layers and ii) the movement of the shutter flaps is partially controlled by the application of an electric field between the shutter flap and the substrate (vertical support grid). The whole mission would be compromised if radiation exposure were to prevent the shutters from opening and closing properly. energetic ionizing particles. Because it is located A unique feature of the MSA is that, as outside the spacecraft and has very little shielding, previously mentioned, it will have to operate at temperatures near 30 K. To date, there are no published reports on how very low temperatures (- 30K) affect the response of MEMS devices to total ionizing dose. Experiments on SiO2 structures at low temperatures (80 K) indicate that the electrons generated by the ionizing radiation are mobile and will move rapidly under the application of an external electric field. Holes, on the other hand, that would normally move in the opposite direction through the SiO2 via a "thermal hopping" process, are effectively immobile at low electric fields as they are trapped close to their generation sites. However, for sufficiently large electric fields (greater than 3 MV/cm) holes are able to move through the SiO2. The larger the field, the more rapidly the holes move. The separation of the electrons and holes leads to a reduced electric field within the insulating layer. To overcome this reduction in electric field, a greater external voltage will have to be applied that alters the normal operation of the device. This report presents the results of radiation testing of the MSA at 60 K. The temperature was higher than the targeted temperature because of a faulty electrical interconnect on the test board. Specifically, our goal was to determine whether the MSA would function propey

  14. Orbit Determination Issues and Results to Incorporate Optical Measurements in Conjunction Operations

    NASA Astrophysics Data System (ADS)

    Vallado, David A.; Kelso, T. S.; Agapov, Vladimir; Molotov, Igor

    2009-03-01

    Operations in geosynchronous orbit are important for many aspects of commerce. Avoiding conjunctions between an ever increasingly crowded geosynchronous environment is therefore becoming more important especially in light of the Iridium 33 - Cosmos 2251 collision. SOCRATES has processed Two-Line Element (TLE) set information for over 5 years. Unfortunately, the TLE information is of limited quality, and obtaining high quality ephemerides is difficult. A next step is to see how we can replace the TLE data for those objects for which we do not get operator data (non-participating SOCRATES-GEO oerational satellites or debris). The International Scientific Observing Network (ISON) is an excellent resource to obtain high-quality observations on satellites. The paper introduces the orbit determination, along with test cases and comparisons with known operator orbits. Finally, we discuss how these observations could be used operationally in the conjunction processing and what considerations should be taken into account.

  15. Results of multiple ligament injured knees operated by three different strategies

    PubMed Central

    Sun, Lei; Wu, Bo; Tian, Min; Luo, Yong Zhong

    2016-01-01

    Background: Multiple ligament injured knee is generally described for a scenario when at least 2 of the 4 major ligaments are ruptured. The most effective treatment for these injuries remains controversial. This study presents the clinical outcome of 3 surgical strategies based on personalized treatment. Materials and Methods: Thirty two patients with multiple ligament injured knee were treated by 3 surgical strategies in the acute phase. (1) One-stage: Twelve patients treated by repair and reconstruction of all ruptured ligaments in a single operation. (2) Staged: Eleven patients treated by repair or reconstruction of the extraarticular (EA) ligaments and then intraarticular ligaments in 2nd stage. (3) EA ligament repair: Nine patients underwent only EA ligaments repair. Results: The patients were followed up for an average of 34.7 ± 12.1 months. Significant improvements in knee stabilities (P < 0.01), Lysholm score (P < 0.01) and International Knee Documentation Committee grade (P < 0.01) were noticed in all groups. Of the 32 patients, none had gross mal alignment or gait abnormalities at the latest followup. Comparing the 3 groups, a significant difference in Lysholm score was shown between the one stage group and the EA repair group (P = 0.040); additionally, significant differences were found in 2 subscales of knee injury and osteoarthritis outcome score (P < 0.05). Conclusion: Satisfactory clinical and functional outcomes could be achieved adopting the 3 surgical strategies based on personalized treatment. However, a combination of EA repair and intraarticular repair or reconstruction might be more reasonable options for the young and active patients. PMID:26955175

  16. First Riser Logging in Scientific Ocean Drilling: Operational Planning and results/reality

    NASA Astrophysics Data System (ADS)

    Sanada, Yoshinori; Kyaw Thu, Moe; Kido, Yukari; Kawamura, Yoshihisa; Hino, Ryota; Eguchi, Nabuhisa; Toczko, Sean; Takahashi, Kyoma; 319 Science Party, Iodp

    2010-05-01

    The first wireline logging, downhole stress measurement, and two-ship walkaway VSP (Vertical Seismic Profiling) were conducted in the riser drilled hole during IODP Expedition 319 in 2009. The hole C0009 is first riser drilling hole in ODP/IODP history by JAMSTEC D/V Chikyu. The expedition 319 is one of series of NanTroSEIZE Project, which goal is to reveal earthquake mechanism in Nankai trough seismogenic zone in Japan. The hole C0009 is drilled at TD 1603.7mbsf under 2054m sea water. Sampling cores, cutting analysis, gas monitoring, wireline logging, downhole stress measurement, and two-ship walkaway VSP (Vertical Seismic Profiling) were conducted. This presentation report the operational planning, results and reality. IODP standard wireline logging items: natural gamma-ray, resistivity, density, porosity, sonic velocity, resistivity image were measured. The advantages of riser dilled hole against riserless drilled hole for wireline logging are 1) stable hole condition, 2) accurate environmental correction by controlled drilling mud, and 3) large variation of tool selection because of regular hole size instead of slimhole by conventional IODP riser drilling. A couple of new tools were used for new measurement and improvement of the data quality. The SonicScanner (trademark of Schulumberger) successfully measured compressional and share velocity in very low velocities at the soft sediment, where it has been difficult to measure them with conventional DSI tool. The stress and pore pressure in the borehole were measured with the wireline logging tool, (Schlumberger MDT). The single probe tool enable to measure temporal formation fluid pressure. The double packer tool enable to fracture test by sealing and pumping in the borehole. These in-situ measurement and stress experiment data are very important to understand physical properties and mechanism of fault zone. Super long offset walkaway VSP was conducted to reveal detail subsurface structure and velocity

  17. Overview of physics results from the conclusive operation of the National Spherical Torus Experiment

    NASA Astrophysics Data System (ADS)

    Sabbagh, S. A.; Ahn, J.-W.; Allain, J.; Andre, R.; Balbaky, A.; Bastasz, R.; Battaglia, D.; Bell, M.; Bell, R.; Beiersdorfer, P.; Belova, E.; Berkery, J.; Betti, R.; Bialek, J.; Bigelow, T.; Bitter, M.; Boedo, J.; Bonoli, P.; Boozer, A.; Bortolon, A.; Boyle, D.; Brennan, D.; Breslau, J.; Buttery, R.; Canik, J.; Caravelli, G.; Chang, C.; Crocker, N.; Darrow, D.; Davis, B.; Delgado-Aparicio, L.; Diallo, A.; Ding, S.; D'Ippolito, D.; Domier, C.; Dorland, W.; Ethier, S.; Evans, T.; Ferron, J.; Finkenthal, M.; Foley, J.; Fonck, R.; Frazin, R.; Fredrickson, E.; Fu, G.; Gates, D.; Gerhardt, S.; Glasser, A.; Gorelenkov, N.; Gray, T.; Guo, Y.; Guttenfelder, W.; Hahm, T.; Harvey, R.; Hassanein, A.; Heidbrink, W.; Hill, K.; Hirooka, Y.; Hooper, E. B.; Hosea, J.; Humphreys, D.; Indireshkumar, K.; Jaeger, F.; Jarboe, T.; Jardin, S.; Jaworski, M.; Kaita, R.; Kallman, J.; Katsuro-Hopkins, O.; Kaye, S.; Kessel, C.; Kim, J.; Kolemen, E.; Kramer, G.; Krasheninnikov, S.; Kubota, S.; Kugel, H.; La Haye, R. J.; Lao, L.; LeBlanc, B.; Lee, W.; Lee, K.; Leuer, J.; Levinton, F.; Liang, Y.; Liu, D.; Lore, J.; Luhmann, N., Jr.; Maingi, R.; Majeski, R.; Manickam, J.; Mansfield, D.; Maqueda, R.; Mazzucato, E.; McLean, A.; McCune, D.; McGeehan, B.; McKee, G.; Medley, S.; Meier, E.; Menard, J.; Menon, M.; Meyer, H.; Mikkelsen, D.; Miloshevsky, G.; Mueller, D.; Munsat, T.; Myra, J.; Nelson, B.; Nishino, N.; Nygren, R.; Ono, M.; Osborne, T.; Park, H.; Park, J.; Park, Y. S.; Paul, S.; Peebles, W.; Penaflor, B.; Perkins, R. J.; Phillips, C.; Pigarov, A.; Podesta, M.; Preinhaelter, J.; Raman, R.; Ren, Y.; Rewoldt, G.; Rognlien, T.; Ross, P.; Rowley, C.; Ruskov, E.; Russell, D.; Ruzic, D.; Ryan, P.; Schaffer, M.; Schuster, E.; Scotti, F.; Shaing, K.; Shevchenko, V.; Shinohara, K.; Sizyuk, V.; Skinner, C. H.; Smirnov, A.; Smith, D.; Snyder, P.; Solomon, W.; Sontag, A.; Soukhanovskii, V.; Stoltzfus-Dueck, T.; Stotler, D.; Stratton, B.; Stutman, D.; Takahashi, H.; Takase, Y.; Tamura, N.; Tang, X.; Taylor, G.; Taylor, C.; Tritz, K.; Tsarouhas, D.; Umansky, M.; Urban, J.; Untergberg, E.; Walker, M.; Wampler, W.; Wang, W.; Whaley, J.; White, R.; Wilgen, J.; Wilson, R.; Wong, K. L.; Wright, J.; Xia, Z.; Youchison, D.; Yu, G.; Yuh, H.; Zakharov, L.; Zemlyanov, D.; Zimmer, G.; Zweben, S. J.

    2013-10-01

    Research on the National Spherical Torus Experiment, NSTX, targets physics understanding needed for extrapolation to a steady-state ST Fusion Nuclear Science Facility, pilot plant, or DEMO. The unique ST operational space is leveraged to test physics theories for next-step tokamak operation, including ITER. Present research also examines implications for the coming device upgrade, NSTX-U. An energy confinement time, τE, scaling unified for varied wall conditions exhibits a strong improvement of BTτE with decreased electron collisionality, accentuated by lithium (Li) wall conditioning. This result is consistent with nonlinear microtearing simulations that match the experimental electron diffusivity quantitatively and predict reduced electron heat transport at lower collisionality. Beam-emission spectroscopy measurements in the steep gradient region of the pedestal indicate the poloidal correlation length of turbulence of about ten ion gyroradii increases at higher electron density gradient and lower Ti gradient, consistent with turbulence caused by trapped electron instabilities. Density fluctuations in the pedestal top region indicate ion-scale microturbulence compatible with ion temperature gradient and/or kinetic ballooning mode instabilities. Plasma characteristics change nearly continuously with increasing Li evaporation and edge localized modes (ELMs) stabilize due to edge density gradient alteration. Global mode stability studies show stabilizing resonant kinetic effects are enhanced at lower collisionality, but in stark contrast have almost no dependence on collisionality when the plasma is off-resonance. Combined resistive wall mode radial and poloidal field sensor feedback was used to control n = 1 perturbations and improve stability. The disruption probability due to unstable resistive wall modes (RWMs) was surprisingly reduced at very high βN/li > 10 consistent with low frequency magnetohydrodynamic spectroscopy measurements of mode stability. Greater

  18. First Operational Results with the SST-1 Superconducting Magnet & its Cryogenics

    NASA Astrophysics Data System (ADS)

    Pradhan, S.; Tanna, V.; Sharma, A.; Khan, Z.; Prasad, U.; Doshi, K.; Khristi, Y.; Parghi, B.; Banoudha, M.; Mahesuria, G.; Patel, R.; Panchal, P.; Panchal, R.; Tank, J.; Sonara, D.; Sharma, D.; Vora, M.; Varadarajulu, A.

    The Steady State Superconducting Tokamak (SST-1) at the Institute for Plasma Research was commissioned in 2013 with the successful experimental validations of its magnets and cryogenic systems. Subsequently, the first plasma in SST-1 has been obtained on June 20, 2013. Since then, the cryo-magnetic systems of SST-1 have been operating reliably, in successive plasma campaigns. Unlike other contemporary cable-in-conduit-conductor (CICC) based superconducting Tokamak magnets, SST-1 CICC in Toroidal Field (TF) winding packs are cooled with two phase helium from a dedicated 1.3 kW helium refrigerator liquefier plant. The TF magnets in SST-1 together with other magnets have been supporting creditable plasma operational scenarios since then, with the TF magnets being charged up to a maximum of 2.0 T on the plasma major radius so far. The vapour cooled current leads of SST-1 are also uniquely operated with cooled helium vapour all along, instead of liquid helium being stored in the lower superconducting sections. The operational experiences with SST-1 TF magnets, PF magnets, and the supporting 5 K and 80 K cryogenic systems contributing towards successful operations of SST-1 plasma experiments are elaborated in this paper.

  19. The transosseous ACL Refixation and biological Augmentation "TARBA". Preliminary Results of a new Operation Technique

    PubMed Central

    Hinterwimmer, Stefan; Achten, Manfred; Bathish, Einal

    2016-01-01

    Aims and Objectives: Differentiated gradings of anterior cruciate ligament (ACL) tear-types allow us to perform a more and more differentiated treatment of this injury. Especially in the tears close to the insertion ACL preserving techniques like "healing response" together with growth factors or synthetic augmentations of the original ACL like the "dynamic intraligamentous stabilization DIS" have increasing importance. Disadvantages of the mentioned techniques are the limited indications and the high need of material. That led us to the development of the "transosseous ACL refixation and biological augmentation TARBA", in which the original ACL is refixed to the femoral insertion and augmented with the patient’s doubled gracilis tendon. In the following we will present the first results with this technique. Materials and Methods: From 12/2013 to 02/2015 we used this technique in 56 patients (28x m, 28x f, age 30.7years). All patients had ACL tears in the proximal third close to the femoral insertion. The original ACL was fixed arthroscopically with 2 PDS fibres. Those were pulled out of the femur through a 5mm channel. The original-ACL was augmented with a doubled ipsilateral gracilis tendon. This tendon graft was pulled into the joint via another tibial 5mm channel and fixed at the femur with an endobutton and at the tibia with a cortical anchor screw. Both channels were placed exactly adjacent to the centre of the femoral and tibial anatomic insertion sites. The treatment result was controlled after 3, 6, 9 and 12 months with clinical examination and various scores (patient satisfaction, VAS, Lysholm, Tegner, Activity Rating Scale). After 6 months an instrumented stability test (Rolimeter) was performed. All patients were matched with 47 patients who had a complete ACL tear treated with 4-strand stemitendinosus tendon (control group). Results: Until now all patients with "TARBA" were satisfied with their operation. The range of motion was equal to the healthy

  20. Results of an Advanced Fan Stage Operating Over a Wide Range of Speed and Bypass Ratio. Part 1; Fan Stage Design and Experimental Results

    NASA Technical Reports Server (NTRS)

    Suder, Kenneth L.; Prahst, Patricia S.; Thorp, Scott A.

    2011-01-01

    NASA s Fundamental Aeronautics Program is investigating turbine-based combined cycle (TBCC) propulsion systems for access to space because it provides the potential for aircraft-like, space-launch operations that may significantly reduce launch costs and improve safety. To this end, National Aeronautics and Space Administration (NASA) and General Electric (GE) teamed to design a Mach 4 variable cycle turbofan/ramjet engine for access to space. To enable the wide operating range of a Mach 4+ variable cycle turbofan ramjet required the development of a unique fan stage design capable of multi-point operation to accommodate variations in bypass ratio (10 ), fan speed (7 ), inlet mass flow (3.5 ), inlet pressure (8 ), and inlet temperature (3 ). In this paper, NASA has set out to characterize a TBCC engine fan stage aerodynamic performance and stability limits over a wide operating range including power-on and hypersonic-unique "windmill" operation. Herein, we will present the fan stage design, and the experimental test results of the fan stage operating from 15 to 100 percent corrected design speed. Whereas, in the companion paper, we will provide an assessment of NASA s APNASA code s ability to predict the fan stage performance and operability over a wide range of speed and bypass ratio.

  1. Evaluation results after seven years of operation for the permanent Hellenic Seismological Network of Crete (HSNC).

    NASA Astrophysics Data System (ADS)

    Vallianatos, F.; Hloupis, G.; Papadopoulos, I.

    2012-04-01

    The Hellenic arc and the adjacent areas of the Greek mainland are the most active in western Eurasia and some of the most seismically active zones of the world. The seismicity of South Aegean is extremely high and is characterised by the frequent occurrence of large shallow and intermediate depth earthquakes. Until 2004, the installed seismological stations from several providers (NOA, GEOFON, MEDNET) provide average interstation distance around 130km resulting to catalogues with minimum magnitude of completeness (Mc) equals to 3.7. Towards to the direction of providing dense and state of the art instrumental coverage of seismicity in the South Aegean, HSNC begun its operation in 2004. Today it consists of (12) permanent seismological stations equipped with short period and broadband seismographs coupled with 3rd generation 24bit data loggers as well as from (2) accelerographs . The addition of HSNC along with combined use of all the active networks in South Aegean area (NOA, GEOFON, AUTH) decrease the average interstation distance to 60km and provide catalogues with Mc≥3.2. Data transmission and telemetry is implemented by a hybrid network consisting of dedicated wired ADSL links as well as VSAT links by using a unique private satellite hub. Real time data spread over collaborating networks (AUTH) and laboratories (Department of Earth Science - UCL) while at the same time, events are appended automatically and manually to EMSC database. Additional value to the network is provided by means of prototype systems which deployed in-situ for the purposes of: a) Acquiring aftershock data in the minimum time after main event. This is a mobile seismological network called RaDeSeis (Rapid Deployment Seismological network) which consists of a central station acting also as the central communication hub and wifi coupled mobile stations. b) The development of dedicated hardware and software solutions for rapid installation times (around 1 hour for each station) leading to

  2. SSPS-CRS first period of operation: preliminary operation results, experiences, and events. IEA Small Solar Power Systems Project SR4

    SciTech Connect

    Bucher, W.

    1984-05-01

    Some lessons learned from operating the SSPS-CRS plant for over one and a half years are presented and major results from the evaluation of plant performance data are provided. Meteorological conditions at the site during the period of operation are described, including insolation, wind, temperatures, precipitation, and a thunderstorm. The performance of the heliostat field system, receiver, sodium heat transfer system, and power conversion system is discussed, and results are given of heliostat flux measurements, receiver efficiencies and losses, sodium heat transfer system losses, heat transfer system performance and efficiency. (LEW)

  3. Operation of a computer aided drafting system: improvements, results and hopes

    SciTech Connect

    Millaud, J.; Goulding, F.; Salz, P.; Shimada, K.

    1983-10-01

    A two workstation Computer Aided Drafting system has been in operation since September 1982 at the Lawrence Berkeley Laboratory, Department of Instrument Science and Engineering. Improvements made to the original hardware and software configuration are described. Benefits from this installation are reported and future developments are outlined.

  4. Form and Function: The Impact of Query Term and Operator Usage on Web Search Results.

    ERIC Educational Resources Information Center

    Lucas, Wendy; Topi, Heikki

    2002-01-01

    Describes a study of college students that investigated Web-based search engine queries and compared relevancy ratings with expert-formulated queries. Considers the number of subject terms used and the use of Boolean operators and discuses the need for designing search engine interfaces that provide greater support in term selection and operator…

  5. Results from VIRTIS on board Venus Express after the end of the mission operations

    NASA Astrophysics Data System (ADS)

    Piccioni, G.; Drossart, P.; VIRTIS Venus Express team

    After more than 8 years since the orbit insertion, the Venus Express mission is now at its end of mission operations. VIRTIS aboard the Venus Express spacecraft has addressed a significant amount of scientific results from the surface up to the upper atmosphere, in terms of mapping, composition, structure and dynamics. The VIRTIS instrument consists of two channels: VIRTIS-M, an imaging spectrometer with moderate spectral resolution in the range from 0.25 to 5.2 mu m and VIRTIS-H, a high spectral resolution spectrometer in the range from 2 to 5 mu m co-aligned with the field of view of –M \\citep{Piccioni2007a,Drossart2007a}. The resolution of VIRTIS-M is 2 nm from 0.25 to 1 mu m, and 10 nm from 1 to 5.2 mu m. The resolution of VIRTIS-H is about 2 nm. The atmosphere above the clouds has been observed both on day and night sides, in solar reflection and thermal emission in nadir geometry \\citep{Ignatiev2009, Cottini2012, Peralta2012, Peralta2009}. Limb observations provided O2\\citep{Piccioni2009, Garcia2009a, Gerard2013, Migliorini2013a, Gerard2008, Gerard2009}, OH \\citep{Piccioni2008,Gerard2010,Soret2010,Soret2012}, NO \\citep{Garcia2009b}, CO2 \\citep{Drossart2007b,Lopez-Valverde2011} and CO \\citep{Gilli2009,Gilli2015,Gilli2011} emissions, through nightglow and fluorescence observations. Spectroscopy of the 4-5 mu m range gave access to the cloud structure in the 60-95 km altitude levels \\citep{Irwin2008a,Grassi2014, Grassi2008,Grassi2010,Luz2011}. The deeper atmospheric windows, limited by CO2 and H2O bands were accessible only in thermal emission on the night side. The sounded levels at 1.7 and 2.3 mu m were limited respectively to 30-20 km altitude \\citep{Barstow2012,Bezard2009,Marcq2008a,Satoh2009,Tsang2009, Tsang2010,Tsang2008,Wilson2008,Wilson2009}, while at shorter wavelengths (1.18, 1.10, 1.01, 0.9 and 0.85 mu m), the hot surface of Venus was seen through the scattering clouds \\citep{Mueller2009,Helbert2008,Arnold2008a,Smrekar2010,Mueller2012

  6. Report of results of benchmarking survey of central heating operations at NASA centers and various corporations

    NASA Astrophysics Data System (ADS)

    Hoffman, Thomas R.

    1995-08-01

    In recent years, Total Quality Management has swept across the country. Many companies and the Government have started looking at every aspect on how business is done and how money is spent. The idea or goal is to provide a service that is better, faster and cheaper. The first step in this process is to document or measure the process or operation as it stands now. For Lewis Research Center, this report is the first step in the analysis of heating plant operations. This report establishes the original benchmark that can be referred to in the future. The report also provides a comparison to other organization's heating plants to help in the brainstorming of new ideas. The next step is to propose and implement changes that would meet the goals as mentioned above. After the changes have been implemented the measuring process starts over again. This provides for a continuous improvement process.

  7. Report of results of benchmarking survey of central heating operations at NASA centers and various corporations

    NASA Technical Reports Server (NTRS)

    Hoffman, Thomas R.

    1995-01-01

    In recent years, Total Quality Management has swept across the country. Many companies and the Government have started looking at every aspect on how business is done and how money is spent. The idea or goal is to provide a service that is better, faster and cheaper. The first step in this process is to document or measure the process or operation as it stands now. For Lewis Research Center, this report is the first step in the analysis of heating plant operations. This report establishes the original benchmark that can be referred to in the future. The report also provides a comparison to other organization's heating plants to help in the brainstorming of new ideas. The next step is to propose and implement changes that would meet the goals as mentioned above. After the changes have been implemented the measuring process starts over again. This provides for a continuous improvement process.

  8. Underground operation of the ICARUS T600 LAr-TPC: first results

    NASA Astrophysics Data System (ADS)

    Rubbia, C.; Antonello, M.; Aprili, P.; Baibussinov, B.; Baldo Ceolin, M.; Barzè, L.; Benetti, P.; Calligarich, E.; Canci, N.; Carbonara, F.; Cavanna, F.; Centro, S.; Cesana, A.; Cieslik, K.; Cline, D. B.; Cocco, A. G.; Dabrowska, A.; Dequal, D.; Dermenev, A.; Dolfini, R.; Farnese, C.; Fava, A.; Ferrari, A.; Fiorillo, G.; Gibin, D.; Gigli Berzolari, A.; Gninenko, S.; Golan, T.; Guglielmi, A.; Haranczyk, M.; Holeczek, J.; Karbowniczek, P.; Kirsanov, M.; Kisiel, J.; Kochanek, I.; Lagoda, J.; Lantz, M.; Mania, S.; Mannocchi, G.; Mauri, F.; Menegolli, A.; Meng, G.; Montanari, C.; Muraro, S.; Otwinowski, S.; Palamara, O.; Palczewski, T. J.; Periale, L.; Piazzoli, A.; Picchi, P.; Pietropaolo, F.; Plonski, P.; Prata, M.; Przewlocki, P.; Rappoldi, A.; Raselli, G. L.; Rossella, M.; Sala, P.; Scantamburlo, E.; Scaramelli, A.; Segreto, E.; Sergiampietri, F.; Sobczyk, J.; Stefan, D.; Stepaniak, J.; Sulej, R.; Szarska, M.; Terrani, M.; Varanini, F.; Ventura, S.; Vignoli, C.; Wachala, T.; Wang, H.; Yang, X.; Zalewska, A.; Zaremba, K.; Zmuda, J.

    2011-07-01

    Important open questions are still present in fundamental Physics and Cosmology, like the nature of Dark Matter, the matter-antimatter asymmetry and the validity of the Standard Model of particle interactions. Addressing these questions requires a new generation of massive particle detectors to explore the subatomic and astrophysical worlds. ICARUS T600 is the first large mass (760 tons) example of a new generation of detectors able to combine the imaging capabilities of the old famous ``bubble chamber'' with the excellent energy measurement of huge electronic detectors. ICARUS T600 now operates at the Gran Sasso underground laboratory and is used to study cosmic rays, neutrino oscillations and the proton decay. The potential for doing physics of this novel telescope is presented through a few examples of neutrino interactions reconstructed with unprecedented detail. Detector design and early operation are also reported.

  9. Empirical correlation of residual gamma radiation resulting from operation of the Health Physics Research Reactor

    SciTech Connect

    Chou, T.L.; Ragan, G.E.; Sims, C.S.

    1985-04-01

    An empirical equation has been developed which gives gamma dose equivalent rate as a function of time, distance, and fission yield after a pulsed operation of Oak Ridge National Laboratory's (ORNL) unshielded Health Physics Research Reactor (HPRR). A related expression which is applicable to steady-state reactor operation has been mathematically derived from the aforementioned empirical equation. The two relations can be used to predict the gamma dose equivalent rate to within 25% for times between 1 minute and 90 minutes after reactor shutdown. Similar agreement is expected for up to several days. In most cases the relations are expected to overestimate the gamma dose equivalent rate. 5 refs., 4 figs., 1 tab.

  10. Multi-mode spectrographs for small telescopes: design, operation, performances and results

    NASA Astrophysics Data System (ADS)

    Munari, U.; Valisa, P.

    2014-03-01

    We present three generations (Mark.I, II and III) of spectrographs we put into operation with ANS Collaboration 0.61m, 0.70m and 0.84m telescopes. These spectrographs are of the Multi-Mode type, allowing for rapid interchange between Echelle high dispersion and two separate single dispersion modes (low and medium resolution). All three modes are long-slit, rotate to any angle (including parallactic compensation for atmospheric dispersion), allow to select among different comparison lamps, and are auto-guided by TV imaging the slit, which is continuously adjustable in width and by a step decker in height. The latest Mark.III model adds many new features including remote operation, spatial splitting of order overlap in single dispersion modes, interchange between prism and grating cross-dispersion in the Echelle mode, spectropolarimetry, a coronagraphic mode and direct filtered imaging without removing the spectrograph from the Cassegrain focus.

  11. Initial results from the operation of village hybrid systems in Chile

    SciTech Connect

    Holz, R.; Baring-Gould, E.I.; Corbus, D.

    1997-08-01

    The government of Chile has undertaken a rural electrification program to electrify 75% of the population by the year 2000. Renewable energy is considered within this program, and its application facilitated through a technical cooperation agreement between Chile`s national energy commission (CNE) and the U.S. Department of Energy. In order to introduce isolated mini-grid hybrid wind-energy systems into Chile, three pilot projects were implemented in Region IX. The goal of the pilot systems is to establish renewables as a viable option for rural electrification in the Chilean context. In this paper we report on the first six months of three pilot projects. Presented as background information are brief descriptions of the power systems, data acquisition systems, and the operation and maintenance (O&M) protocols. Analyses of loads, component performance, system operation, and balance of payments for O&M are the primary points presented. Important lessons learned and future plans are also discussed.

  12. Initial results from the operation of two argon ion generators in the auroral ionosphere

    NASA Technical Reports Server (NTRS)

    Erlandson, R. E.; Cahill, L. J., Jr.; Pollock, C. J.; Arnoldy, R. L.; Scales, W. A.

    1987-01-01

    Two argon ion generators have been lofted by sounding rockets in order to investigate ion beam dynamics and beam effects on the ionosphere, and auroral electrodynamics during rocket passage over auroral arcs. The ion generators were on a subpayload that was separated from the main payload early in the flight. The main payload conducted the diagnostic measurements during ion beam operations. Evidence of heating of the ionosphere around the subpayload during each ion beam emission is noted.

  13. CERN’s Linac4 H{sup −} sources: Status and operational results

    SciTech Connect

    Lettry, J. Aguglia, D.; Andersson, P.; Bertolo, S.; Butterworth, A.; Coutron, Y.; Dallocchio, A.; David, N.; Chaudet, E.; Fink, D.; Gil-Flores, J.; Garlasche, M.; Grudiev, A.; Guida, R.; Hansen, J.; Haase, M.; Jones, A.; Koszar, I.; Machado, C.; Mastrostefano, C.; and others

    2015-04-08

    Two volume sources equipped with DESY and CERN plasma generators and a low voltage electron dump were operated at 45 kV in the Linac4 tunnel and on a dedicated test stand. These volume sources delivered approximately 20 mA and ensured the commissioning of the Radio Frequency Quadrupole accelerator and of the first section of the Drift Tube Linac. CERN’s prototype of a cesiated surface source equipped with this electron dump was operated continuously from November 2013 to April 2014 on the ion source test stand and is being commissioned in the Linac4 tunnel. Before cesiation, the prototype conditioned in volume mode provided up to 30 mA H{sup −} beam. Short cesiations, of the order of 10 mg effectively reduced the intensity of co-extracted electrons down to 2 - 8 times the H{sup −} current; this cesiated surface operation mode delivered up to 60 mA H{sup −} beam. An H{sup −} beam of the order of 40 mA was sustained up to four weeks operation with 500 μs pulses at 1.2s spacing. A new extraction was designed to match these beam properties. A copy of BNL’s magnetron produced at CERN was tested at BNL and delivered at 40 kV H{sup −} beam exceeding Linac4’s nominal intensity of 80 mA. In this contribution, the performances, dynamic response to cesiation, stability and availability of these prototypes are described. The needed optimization of the emittance of H{sup −} beam above 40 mA is presented, which requires an evolution of the front end that encompasses implementation of a large ceramic insulator.

  14. Development of a hydro kinetic river turbine with simulation and operational measurement results in comparison

    NASA Astrophysics Data System (ADS)

    Ruopp, A.; Ruprecht, A.; Riedelbauch, S.; Arnaud, G.; Hamad, I.

    2014-03-01

    The development of a hydro-kinetic prototype was shown including the compound structure, guide vanes, runner blades and a draft tube section with a steeply sloping, short spoiler. The design process of the hydrodynamic layout was split into three major steps. First the compound and the draft tube section was designed and the best operating point was identified using porous media as replacement for the guide vane and runner section (step one). The best operating point and the volume flux as well as the pressure drop was identified and used for the design of the guide vane section and the runner section. Both were designed and simulated independently (step two). In step three, all parts were merged in stationary simulation runs detecting peak power and operational bandwidth. In addition, the full scale demonstrator was installed in August 2010 and measured in the St. Lawrence River in Quebec supporting the average inflow velocity using ADCP (Acoustic Doppler Current Profiler) and the generator power output over the variable rotational speed. Simulation data and measurements are in good agreement. Thus, the presented approach is a suitable way in designing a hydro kinetic turbine.

  15. Simulated Rotor Wake Interactions Resulting from Civil Tiltrotor Aircraft Operations Near Vertiport Terminals

    NASA Technical Reports Server (NTRS)

    Young, Larry A.; Rajagopalan, Ganesh

    2013-01-01

    A mid-fidelity computational fluid dynamics tool called RotCFD - specifically developed to aid in rotorcraft conceptual design efforts - has been applied to the study of rotor wake interactions of civil tiltrotor aircraft in the immediate vicinity of vertiport/airport ground infrastructure. This issue has grown in importance as previous NASA studies have suggested that civil tiltrotor aircraft can potentially have a significant impact on commercial transport aviation. Current NASA reference designs for such civil tiltrotor aircraft are focused on a size category of 90-120 passengers. Notional concepts of operations include simultaneous non-interfering flight into and out of congested airports having vertiports, that is, prepared VTOL takeoff and landing zones, or underutilized short runways for STOL operation. Such large gross-weight vehicles will be generating very high induced velocities. Inevitably, the interaction of the rotor wake with ground infrastructure such as terminals/jetways must be considered both from an operational as well as design perspective.

  16. What Happened at Hawthorne?: New evidence suggests the Hawthorne effect resulted from operant reinforcement contingencies.

    PubMed

    Parsons, H M

    1974-03-01

    The Hawthorne effect in experimental research is the unwanted effect of the experimental operations themselves. Following the Hawthorne studies, various explanations have been proposed to account for rising rates of production. Although in the Relay Assembly Test Room experiment the experimental operations may have produced other extraneous variables, a reexamination based on new and neglected evidence has yielded a new interpretation. The new variable, made more plausible because research in other contexts has shown it to have similar effects, is a combination of information feedback and financial reward. It is an example of the control of behavior by its consequences. Although several approaches may be taken to explain the effects of response-consequence contingencies, I have favored operant conditioning because it seems to account for progressive increases in response rate-the Hawthorne phenomenon. Generalizing from the particular situation at Hawthorne, I would define the Hawthorne effect as the confounding that occurs if experimenters fail to realize how the consequences of subjects' performance affect what subjects do. But the Hawthorne effect need not be viewed solely as a problem in conducting experiments. The phenomenon that created it should be studied in its own right, as Sommer (67) suggested with a different phenomenon in mind. The study of response-consequence contingencies might well be extended to the examination of motivation in industrial workers. PMID:17756742

  17. Optical computed tomography utilizing a rotating mirror and Fresnel lenses: operating principles and preliminary results

    NASA Astrophysics Data System (ADS)

    Xu, Y.; Wuu, Cheng-Shie

    2013-02-01

    the phantom positioning between the reference scan and the actual scan is demonstrated to be essential. The fast scanner is shown to be able to scan gel phantoms with a wider field of view (5 mm from the edge of the scanned dosimeters) and at a speed 10 to 20 times faster than the OCTOPUS™ scanner. A large uncertainty of 5% (defined as the ratio of the standard deviation to the mean) is typically observed in the reconstructed images, owing to the inaccuracy in the phantom positioning process. Methods for further improvement of the accuracy of the in-house modified OCTOPUS™-10× scanner are discussed.

  18. Concept of operation and preliminary experimental results of the DRDC through-wall SAR system

    NASA Astrophysics Data System (ADS)

    Sévigny, Pascale; DiFilippo, David J.; Laneve, Tony; Chan, Brigitte; Fournier, Jonathan; Roy, Simon; Ricard, Benoît; Maheux, Jean

    2010-04-01

    Mapping the interior of buildings is of great interest to military forces operating in an urban battlefield. Throughwall radars have the potential of mapping interior room layout, including the location of walls, doors and furniture. They could provide information on the in-wall structure, and detect objects of interest concealed in buildings, such as persons and arms caches. We are proposing to provide further context to the end user by fusing the radar data with LIDAR (Light Detection and Ranging) images of the building exterior. In this paper, we present our system concept of operation, which involves a vehicle driven along a path in front of a building of interest. The vehicle is equipped with both radar and LIDAR systems, as well as a motion compensation unit. We describe our ultra wideband through-wall L-band radar system which uses stretch processing techniques to obtain high range resolution, and synthetic aperture radar (SAR) techniques to achieve good azimuth resolution. We demonstrate its current 2-D capabilities with experimental data, and discuss the current progress in using array processing in elevation to provide a 3-D image. Finally, we show preliminary data fusion of SAR and LIDAR data.

  19. Preliminary results of geothermal desalting operations at the East Mesa test site Imperial Valley, California

    NASA Technical Reports Server (NTRS)

    Suemoto, S. H.; Mathias, K. E.

    1974-01-01

    The Bureau of Reclamation has erected at its Geothermal Resource Development site two experimental test vehicles for the purpose of desalting hot fluids of geothermal origin. Both plants have as a feed source geothermal well Mesa 6-1 drilled to a total depth of 8,030 feet and having a bottom hole temperature of 400 F. Formation fluid collected at the surface contained 24,800 mg/1 total dissolved solids. The dissolved solids consist mainly of sodium chloride. A multistage distillation (3-stage) plant has been operated intermittently for one year with no operational problems. Functioning at steady-state conditions with a liquid feed rate of 70 g/m and a temperature of 221 F, the final brine blowdown temperature was 169 F. Product water was produced at a rate of about 2 g/m; average total dissolved solids content of the product was 170 mg/1. A product quality of 27.5 mg/1 at a pH of 9.5 was produced from the first stage.

  20. Building upon the Electronic Geophysical Year (eGY) Experience: Transitioning Research Results to Operations (Invited)

    NASA Astrophysics Data System (ADS)

    Baker, D.

    2009-12-01

    The past 15 years have seen the development of many cost effective ways to acquire, store, and exchange data. We have the potential to expand the exchange of data by allowing working scientists and operational agencies to access and manipulate information and models from large interdisciplinary centers as well as from small, previously isolated, research groups. The key to this technology requires adoption of community-developed standards for data storage and description to form an ''Informatics Commons.'' Scientific societies currently promote the establishment of a system of Virtual Observatories. The Electronic Geophysical Year (eGY) concept (2007-2008) embraced all available and upcoming geophysical data (e.g., atmospheric, geomagnetic, ionospheric, magnetospheric, etc.) and advocated organizing them into a series of virtual geophysical observatories deployed in cyberspace. This concept allows access to all available data through the Internet and World Wide Web, taking advantage of existing networking hardware and software technologies (e.g., Internet, XML, Service-Oriented Architectures, Semantic Web, etc.). The eGY provided an international focus for a resolve to address the issues of data release, data discovery, and data preservation. This effort can help revolutionize the transition of basic research to a state of operational readiness.

  1. Wind tunnel results of advanced high speed propellers in the takeoff, climb, and landing operating regimes

    NASA Technical Reports Server (NTRS)

    Stefko, G. L.; Jeracki, R. J.

    1985-01-01

    Low speed wind tunnel performance tests of two advanced propellers were completed. The 62.2 cm diameter adjustable pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds in the 10 by 10 ft Supersonic Wind Tunnel. Both models had eight blades and a cruise design point operating condition of 0.80 Mach number, 10.668 km S.A. altitude, 243.8 m/s tip speed and a high power loading of 301 kW sq m. No adverse or unusual low speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propellers. The 45 deg swept propeller efficiency exceeded the straight blade efficiency by 4 to 5 percent. Typical net efficiencies of the straight and 45 deg swept propeller at a Mach 0.20 takeoff condition were 50.2 and 54.9 percent respectively. At a Mach 0.34 climb condition, the efficiencies were 53.7 and 59.1 percent. Reverse thrust data indicates that these propellers are capable of producing more reverse thrust at Mach 0.20 than a high bypass turbofan engine at Mach 0.20.

  2. Wind tunnel results of advanced high speed propellers in the takeoff, climb and landing operating regimes

    NASA Technical Reports Server (NTRS)

    Stefko, G. L.; Jeracki, R. J.

    1985-01-01

    Low speed wind tunnel performance tests of two advanced propellers were completed. The 62.2 cm diameter adjustable pitch models were tested at Mach numbers typical of takeoff, initial climbout, and landing speeds in the 10 by 10 ft Supersonic Wind Tunnel. Both models had eight blades and a cruise design point operating condition of 0.80 Mach number, 10.668 km S.A. altitude, 243.8 m/s tip speed and a high power loading of 301 kW sq m. No adverse or unusual low speed operating conditions were found during the test with either the straight blade SR-2 or the 45 deg swept SR-3 propellers. The 45 deg swept propeller efficiency exceeded the straight blade efficiency by 4 to 5%. Typical net efficiencies of the straight and 45 deg swept propeller at a Mach 0.20 takeoff condition were 50.2 and 54.9% respectively. At a Mach 0.34 climb condition, the efficiencies were 53.7 and 59.1%. Reverse thrust data indicates that these propellers are capable of producing more reverse thrust at Mach 0.20 than a high bypass turbofan engine at Mach 0.20.

  3. Optical computed tomography utilizing a rotating mirror and Fresnel lenses: operating principles and preliminary results.

    PubMed

    Xu, Y; Wuu, Cheng-Shie

    2013-02-01

    -millimeter accuracy of the phantom positioning between the reference scan and the actual scan is demonstrated to be essential. The fast scanner is shown to be able to scan gel phantoms with a wider field of view (5 mm from the edge of the scanned dosimeters) and at a speed 10 to 20 times faster than the OCTOPUS™ scanner. A large uncertainty of 5% (defined as the ratio of the standard deviation to the mean) is typically observed in the reconstructed images, owing to the inaccuracy in the phantom positioning process. Methods for further improvement of the accuracy of the in-house modified OCTOPUS™-10× scanner are discussed. PMID:23302492

  4. Results from the Operational Testing of the Eaton Smart Grid Capable Electric Vehicle Supply Equipment

    SciTech Connect

    Bennett, Brion

    2014-10-01

    The Idaho National Laboratory conducted testing and analysis of the Eaton smart grid capable electric vehicle supply equipment (EVSE), which was a deliverable from Eaton for the U.S. Department of Energy FOA-554. The Idaho National Laboratory has extensive knowledge and experience in testing advanced conductive and wireless charging systems though INL’s support of the U.S. Department of Energy’s Advanced Vehicle Testing Activity. This document details the findings from the EVSE operational testing conducted at the Idaho National Laboratory on the Eaton smart grid capable EVSE. The testing conducted on the EVSE included energy efficiency testing, SAE J1772 functionality testing, abnormal conditions testing, and charging of a plug-in vehicle.

  5. Recent results from operation of the ANTARES deep-sea neutrino telescope

    NASA Astrophysics Data System (ADS)

    Hallewell, G. D.

    2014-12-01

    The ANTARES neutrino telescope is currently the largest operating water Cherenkov detector and the largest neutrino detector in the Northern hemisphere. It comprises 885 optical modules distributed on 12 detection lines anchored at a depth of 2.5 km in the Mediterranean Sea near Toulon, France; at a latitude that accesses a large part of the Galactic Plane, including the Galactic Centre. Its main scientific target is the detection of multi-TeV neutrinos predicted in charged cosmic particle acceleration mechanisms. In addition, ANTARES has developed a range of multi-messenger search strategies to look for correlations with optical counterparts and other cosmic messengers including γ-rays and charged cosmic rays. Other topics of investigation include the search for neutrinos from dark matter annihilation, searches for exotic particles and the measurement of neutrino oscillations. Details of the telescope are discussed together with examples of recently-conducted searches.

  6. High performance RO membranes for desalination and wastewater reclamation and their operation results.

    PubMed

    Henmi, M; Fusaoka, Y; Tomioka, H; Kurihara, M

    2010-01-01

    Reverse osmosis (RO) membrane is one of the most powerful tools for solving the global water crisis, and is used in a variety of water treatment scenes such as drinking water purification, waste-water treatment, boiler feed water production, ultra pure water production for semiconductor industry, etc. The desired performance of RO membrane varies according to quality of feed water being treated, and Toray has been developing RO membranes with suitable characteristic for each operating condition. RO membranes for seawater desalination and wastewater reclamation are especially regarded as most promising targets. Recently, high boron removal and energy saving RO membrane for seawater desalination and low fouling RO membrane for wastewater reclamation have been developed. In this paper, the prospect of attaining these renovative RO membrane, and furthermore, job references will be discussed. PMID:21045342

  7. Results from Operational Testing of the Siemens Smart Grid-Capable Electric Vehicle Supply Equipment

    SciTech Connect

    Bennett, Brion

    2015-05-01

    The Idaho National Laboratory conducted testing and analysis of the Siemens smart grid capable electric vehicle supply equipment (EVSE), which was a deliverable from Siemens for the U.S. Department of Energy FOA-554. The Idaho National Laboratory has extensive knowledge and experience in testing advanced conductive and wireless charging systems though INL’s support of the U.S. Department of Energy’s Advanced Vehicle Testing Activity. This document details the findings from the EVSE operational testing conducted at the Idaho National Laboratory on the Siemens smart grid capable EVSE. The testing conducted on the EVSE included energy efficiency testing, SAE J1772 functionality testing, abnormal conditions testing, and charging of a plug-in vehicle.

  8. 17 CFR 229.303 - (Item 303) Management's discussion and analysis of financial condition and results of operations.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Regulation S-X (17 CFR 210), a management's discussion and analysis of the financial condition and results of... discussion and analysis of financial condition and results of operations. 229.303 Section 229.303 Commodity... 1975-REGULATION S-K Financial Information § 229.303 (Item 303) Management's discussion and analysis...

  9. Requirements for long-life operation of inert gas hollow cathodes - Preliminary results

    NASA Technical Reports Server (NTRS)

    Verhey, Timothy R.; Macrae, Gregory S.

    1990-01-01

    An experimental investigation was initiated to establish conditioning procedures for reliable hollow cathode operation via the characterization of critical parameters in a representative cathode test facility. From vacuum pumpdown rates, it was found that approximately 1.5 hours were required to achieve pressure levels within 5 percent of the lowest attainable pressure for this facility, depending on the purge conditions. The facility atmosphere was determined by a residual gas analyzer to be composed of primarily air and water vapor. The effects of vacuum pumping and inert gas purging were evaluated. A maximum effective leakage rate of 2.0 x 10 (exp -3) sccm was observed and its probable causes were examined. An extended test of a 0.64 cm diameter Mo-Re hollow cathode was successfully completed. This test ran for 504 hours at an emission current of 23.0 amperes and a xenon flow rate of 6.1 sccm. Discharge voltage rose continuously from 15 to 21 volts over the course of the test. The temperature of the cathode body during the test was relatively stable at 1160 C. Post-test examination revealed ion-bombardment texturing of the orifice plate to be the only detectable sign of wear on the hollow cathode.

  10. Lake Eĺ gygytgyn Drilling under way: State of the operation and first results

    NASA Astrophysics Data System (ADS)

    Melles, M.; Brigham-Grette, J.; Minyuk, P.; Koeberl, C.; Scientific Party, EĺGygytgyn

    2009-04-01

    Lake Eĺgygytgyn, located in central Chukotka, NE Siberia, was formed 3.6 million years ago by a meteorite impact and has never been glaciated or desiccated. This makes Lake Eĺgygytgyn a unique target of an interdisciplinary, multi-national drilling campaign, which currently is carried out as part of the International Continental Drilling Program (ICDP). Drilling operations started in Nov./Dec. 2008, when a 142 m long sediment core was retrieved from the permafrost deposits in the western lake catchment by the local drilling company Chaun Mine Geological Company (CGE). The core penetrated coarse-grained, ice-rich alluvial sediments with variable contents of fine-grained material. It will be investigated for the environmental history, including potential lake-level changes, and the permafrost characteristics, in order to learn more about the influences of catchment changes on the lake sedimentation. Besides, the hole was permanently instrumented for future ground temperature monitoring as part of the Global Terrestrial Network for Permafrost (www.gtnp.org/index_e.html). The major drilling effort will commence in Febr. 2009, when two sites in the central part of Lake Eĺgygytgyn shall be drilled down to 630 m below the lake floor. Drilling will be carried out by DOSECC, using a new GLAD 800 system that will be operated from an enclosed platform on the lake ice. Drilling objectives include replicate overlapping cores from the up to 420 m thick lake sediment fill. The cores promise to yield the longest, most continuous record of climate change in the terrestrial Arctic, extending back one million years prior to the intensification of the Northern Hemisphere Glaciation at the Pliocene/Pleistocene boundary, thus offering unique insight into the climatic and environmental history of the Arctic and its comparison with records from lower latitude marine and terrestrial sites to better understand hemispheric and global climate change. Coring shall be continued up to 300 m

  11. FY 1995 progress report on the ANS thermal-hydraulic test loop operation and results

    SciTech Connect

    Siman-Tov, M.; Felde, D.K.; Farquharson, G.; McDuffee, J.L.; McFee, M.T.; Ruggles, A.E.; Wendel, M.W.; Yoder, G.L.

    1997-07-01

    The Thermal-Hydraulic Test Loop (THTL) is an experimental facility constructed to support the development of the Advanced Neutron Source Reactor (ANSR) at Oak Ridge National Laboratory (ORNL). The THTL facility was designed and built to provide known thermal-hydraulic (T/H) conditions for a simulated full-length coolant subchannel of the ANS reactor core, thus facilitating experimental determination of FE and CHF thermal limits under expected ANSR T/H conditions. Special consideration was given to allow operation of the system in a stiff mode (constant flow) and in a soft mode (constant pressure drop) for proper implementation of true FE and DNB experiments. The facility is also designed to examine other T/H phenomena, including onset of incipient boiling (IB), single-phase heat transfer coefficients and friction factors, and two-phase heat transfer and pressure drop characteristics. Tests will also be conducted that are representative of decay heat levels at both high pressure and low pressure as well as other quasi-equilibrium conditions encountered during transient scenarios. A total of 22 FE tests and 2 CHF tests were performed during FY 1994 and FY 1995 with water flowing vertically upward. Comparison of these data as well as extensive data from other investigators led to a proposed modification to the Saha and Zuber correlation for onset of significant void (OSV), applied to FE prediction. The modification takes into account a demonstrated dependence of the OSV or FE thermal limits on subcooling levels, especially in the low subcooling regime.

  12. Facebook as a Library Tool: Perceived vs. Actual Use

    ERIC Educational Resources Information Center

    Jacobson, Terra B.

    2011-01-01

    As Facebook has come to dominate the social networking site arena, more libraries have created their own library pages on Facebook to create library awareness and to function as a marketing tool. This paper examines reported versus actual use of Facebook in libraries to identify discrepancies between intended goals and actual use. The results of a…

  13. Perceived and Actual Student Support Needs in Distance Education.

    ERIC Educational Resources Information Center

    Visser, Lya; Visser, Yusra Laila

    2000-01-01

    This study sought to determine the academic, affective, and administrative support expectations of distance education students, and to compare actual expectations of distance education students with the instructor's perceptions of such expectations. Results demonstrated divergence between perceived and actual expectations of student support in…

  14. Self-Actualization Effects Of A Marathon Growth Group

    ERIC Educational Resources Information Center

    Jones, Dorothy S.; Medvene, Arnold M.

    1975-01-01

    This study examined the effects of a marathon group experience on university student's level of self-actualization two days and six weeks after the experience. Gains in self-actualization as a result of marathon group participation depended upon an individual's level of ego strength upon entering the group. (Author)

  15. Operations analysis, study 2.6. Volume 2: Analysis results. [space transportation system

    NASA Technical Reports Server (NTRS)

    Wolfe, R. R.

    1973-01-01

    Results are presented of the assessment of the space transportation system as it applies to future space program planning. Comparisons are given between space servicing and ground refurbishment of payloads. Mission characterization, logistic vehicle options, and payload design options are also discussed.

  16. How Often Do Subscores Have Added Value? Results from Operational and Simulated Data

    ERIC Educational Resources Information Center

    Sinharay, Sandip

    2010-01-01

    Recently, there has been an increasing level of interest in subscores for their potential diagnostic value. Haberman suggested a method based on classical test theory to determine whether subscores have added value over total scores. In this article I first provide a rich collection of results regarding when subscores were found to have added…

  17. Improving Program Results through the Use of Predictive Operational Performance Indicators: A Canadian Case Study

    ERIC Educational Resources Information Center

    Barrados, Maria; Blain, J. S.

    2013-01-01

    In Canada, in-depth evaluations of federal programs are intended to occur every 5 years. As such, evaluation is a periodic retrospective (lag) indicator examining results achieved versus program objectives. In a Canadian context, stand-alone evaluations have proved challenging to implement, time consuming, and not well adapted to annual management…

  18. PFBC plant operations

    SciTech Connect

    Kinsinger, F.L. )

    1992-01-01

    By operating a fluidized bed at elevated pressures, known as pressurized fluidized bed combustion (PFBC), advantages can be gained over atmospheric fluidized bed technology. Operating the process at elevated pressures allows electrical production from both the steam and the gas cycles which results in higher plant efficiencies. Additional benefits of operating at elevated pressures include the further reduction of emissions and the reduction in the physical size of the power plant. This paper describes the operation of a PFBC plant and its application at the Tidd clean coal demonstration project. Actual operating experience will be presented.

  19. GeMS/GSAOI: from commissioning to operations and science results

    NASA Astrophysics Data System (ADS)

    Carrasco, E. R.; Neichel, B.; Rigaut, F.; Winge, C.; Vidal, F.; Pessev, P.; Serio, A.; Arriagada, G.; Rambold, W.; Luhrs, J.; Boccas, M.; Dorgeville, C.; Fesquet, V.; Lopez, A.; Trujillo, C.; Galvez, R.; Gausachs, G.; Araujo, C.; Vucina, T.; Montes, V.; Urrutia, C.; Moreno, C.; Marchant, C.; Collao, F.; Diggs, S.; Collao, F.; Trancho, G.; Bec, M.

    2014-10-01

    The Gemini Multi-conjugate Adaptive Optics System (GeMS) and the Gemini South Adaptive Optics Imager (GSAOI) are unique and complex facility Gemini instruments. GeMS/GSAOI provide a uniform, diffraction limited image quality at near-infrared (NIR) wavelengths over a field of view of 85" x 85" on the sky. The GeMS/GSAOI commissioning started at the beginning of 2011. After ˜ 2 years of dedicated work and more than 90 nights of on-sky commissioning, at the end of 2012 GeMS/GSAOI started to produce the first science results. In this presentation we describe in details the system performance, on-sky efficiency and present the scientific results produced by GeMS/GSAOI during the system verification process.

  20. Results and conclusions: perception sensor study for high speed autonomous operations

    NASA Astrophysics Data System (ADS)

    Schneider, Anne; LaCelle, Zachary; Lacaze, Alberto; Murphy, Karl; Close, Ryan

    2016-05-01

    Previous research has presented work on sensor requirements, specifications, and testing, to evaluate the feasibility of increasing autonomous vehicle system speeds. Discussions included the theoretical background for determining sensor requirements, and the basic test setup and evaluation criteria for comparing existing and prototype sensor designs. This paper will present and discuss the continuation of this work. In particular, this paper will focus on analyzing the problem via a real-world comparison of various sensor technology testing results, as opposed to previous work that utilized more of a theoretical approach. LADAR/LIDAR, radar, visual, and infrared sensors are considered in this research. Results are evaluated against the theoretical, desired perception specifications. Conclusions for utilizing a suite of perception sensors, to achieve the goal of doubling ground vehicle speeds, is also discussed.

  1. Results of JET operation with continuous carbon and beryllium X-point target plates

    NASA Astrophysics Data System (ADS)

    Lowry, C. G.; Ady, W. N.; Campbell, D. J.; Carman, P.; Clement, S.; Deksnis, E. B.; Gondhalekar, A.; Harbour, P. J.; Horton, L.; Janeschitz, G.; Lesourd, M.; Lingertat, J.; Pick, M. A.; Saibene, G.; Summers, D. D. R.; Thomas, P. R.

    1992-12-01

    The 1991/92 JET experimental campaign assessed the performance of three different toroidally continuous X-point target plates. The main differences were in the tile material, beryllium and carbon, and the presence of exposed edges. These three configurations have been tested up to power levels in excess of 22 MW and with gas fuelling at the X-point and in the midplane. With the beryllium a radiating divertor was achieved by puffing deuterium into the X-point region, while rapid ELMs resulted from deuterium puffing on the carbon target. The investigation into the importance of small edges, up to 1.5 mm, yielded some interesting results. Although the surface temperature rise was substantially reduced by eliminating exposed tile edges, the onset of the carbon bloom was not delayed by a similar amount. In this paper a model is presented which can explain this and other features of the bloom.

  2. Operation result of 40kW class MCFC pilot plant

    SciTech Connect

    Saitoh, H.; Hatori, S.; Hosaka, M.; Uematsu, H.

    1996-12-31

    Ishikawajima-Harima Heavy Industries Co., Ltd. developed unique Molten Carbonate Fuel Cell (MCFC) system based on our original concept. To demonstrate the possibility of this system, based on MCFC technology of consigned research from New Energy and Industrial Technology Development Organization (NEDO) in Japan, we designed 40kW class MCFC pilot plant which had all equipments required as a power plant and constructed in our TO-2 Technical Center. This paper presents the test results of the plant.

  3. [Radioimmunologic determination of plasmatic triiodothyronine. Verification of operative parameters; 1st clinical results].

    PubMed

    Dotti, C

    1975-06-01

    The experimental determination of the operative parameters of two radioimmunoassay (RIA) systems for the determination of triiodothyronine (T3) level directly in serum is described. The two systems differ both for the agents blocking the aspecific T3-serum protein bindings (sulphonic acid, 8-aniline, 1-Naphtalene in borate buffer: bor-ANS-RIA and Merthiolate in phosphate buffer: PO4-Merth-RIA) and for the methods adopted for compensating the aspecific serum interferences (T3,4 free serum for bor-ANS-RIA and Human Serum Albumine HSA 8% for PO4-Merth-RIA. The tracers are T3-I125 (spec. act. 500 Ci/g for bor-ANS-RIA and 1000 Ci/g for PO4-Merth-RIA). The antisera have been raised in rabbit (T3-bovine SA conjugate for bor-ANS-RIA and T3-HSA conjugate for PO4-Merth-RIA). The incubation conditions are 2degreesC X 24 h for bor-ANS-RIA and room temp. X 2 h for PO4-Merth-RIA. For both systems, the Bound-Free (B-F) separations are carried out by charcoal-dextrane adsorption, 4 mg/tube, 10 min contact. Indicatively, the lowest detection limits of the two systems are about 8 pg T3 for ANS and about 6 pg T3 for Merth. Evidence of parallelism and even superimposition is provided for both assays between the dose-response curve and the serum dilution curve. The calibration curves of the employed antisera are reported (final titres: 1/1000 for ANS and 1/2500 for Merth). 4 different incubation conditions for ANS and 2 for Merth are described and the reasons of choice of the mentioned conditions statistically elucidated. Acceptable statistical comparison between "sample-blank" and the "blank" of the diluents of the employed standard preparations are presented and discussed. F-countings vs. B-countings functions are reported (regression line -- equations: F = 0.93 B + 0.07, n = 15, r = 0.993 for ANS and F = 0.95 B -- 0.02, n = 14, r = 0.992 for Merth) demonstrating the possibility of alternative countings. The recovery regression lines (found f vs. expected e) have equations: f = 1

  4. Results.

    ERIC Educational Resources Information Center

    Zemsky, Robert; Shaman, Susan; Shapiro, Daniel B.

    2001-01-01

    Describes the Collegiate Results Instrument (CRI), which measures a range of collegiate outcomes for alumni 6 years after graduation. The CRI was designed to target alumni from institutions across market segments and assess their values, abilities, work skills, occupations, and pursuit of lifelong learning. (EV)

  5. The Floating Potential Probe (FPP) for ISS: Operations and Initial Results

    NASA Technical Reports Server (NTRS)

    Ferguson, Dale C.; Hillard, G. Barry; Morton, Thomas L.

    2001-01-01

    In this paper we report early results from the Floating Potential Probe (FPP) recently installed on the International Space Station (ISS). The data show that FPP properly measures the electrical potential of ISS structure with respect to the plasma it is flying through. FPP Langmuir probe data seem to give accurate measurements of the ambient plasma density, and are generally consistent with the IRI-90 model. FPP data are used to judge the performance of the ISS Plasma Contacting Units (PCUs), and to evaluate the extent of ISS charging in the absence of the PCUs.

  6. [Grafting of preserved homogenous cancellous bone. Results of 90 operations (author's transl)].

    PubMed

    Ackermann, W; Taillard, W

    1977-10-01

    Description of a simple technique for the removal of homogeneous cancellous bone from heads of femur removed during replacement of the hip-joint. The material has been preserved for one year at -20 degrees C and can be used after simple washing. Results in 89 grafts are analysed: They all took perfectly at the site of grafting. There was no rejection, no local or general allergy. Risk of infection was not increased. The technique is simple and useful where much cancellous bone is needed. PMID:337707

  7. First trial results of ATES: Advanced telerobotic system for underwater complex operations

    SciTech Connect

    Brambilla, M.; Maddalena, D.; McCavanagh, G.

    1995-12-31

    This paper describes the purposes, the technical approaches, and the first trials results of the ATES system. This R and D project aims at the improvement and the adaptation of innovative robotic technologies and the integration of these technologies with an industrial ROV to set up an advanced underwater telerobot capable of efficiently replacing divers in performing a large spread of complex tasks related to the offshore industry, such as construction support, platform maintenance, subsea plant servicing, etc. The key robotic technologies considered are: supervisory control, scene reconstruction and telepresence. The supervisory control includes also the manipulator force control while the scene reconstruction techniques based on computer vision are able to compensate for the ROV motion during manipulation. To evaluate the technical and economical validity of the system, extensive trials have been carried out, where typical submerged scenario comprising a real node and a well head mock-up has been used. This paper reports the first results of this trial activity demonstrating the improvements in complex task execution and accuracy and the feasibility of such tasks even with a loose docking. The tests are still going in protected water using a work ROV.

  8. Orbit and attitude determination results during launch support operations for SBS-5

    NASA Technical Reports Server (NTRS)

    Hartman, K. R.; Iano, P. J.

    1989-01-01

    Presented are orbit and attitude determination results from the launch of Satellite Business Systems (SBS)-5 satellite on September 8, 1988 by Arianespace. SBS-5 is a (HS-376) spin stabilized spacecraft. The launch vehicle injected the spacecraft into a low inclination transfer orbit. Apogee motor firing (AMF) attitude was achieved with trim maneuvers. An apogee kick motor placed the spacecraft into drift orbit. Postburn, reorientation and spindown maneuvers were performed during the next 25 hours. The spacecraft was on-station 19 days later. The orbit and attitude were determined by both an extended Kalman filter and a weighted least squares batch processor. Although the orbit inclination was low and the launch was near equinox, post-AMF analysis indicated an attitude declination error of 0.034 deg., resulting in a saving of 8.5 pounds of fuel. The AMF velocity error was 0.4 percent below nominal. The post-AMF drift rate was determined with the filter only 2.5 hours after motor firing. The filter was used to monitor and retarget the reorientation to orbit normal in real time.

  9. Performance and operating results from the demonstration of advanced combustion techniques for wall-fired boilers

    SciTech Connect

    Sorge, J.N.; Baldwin, A.L.

    1993-11-01

    This paper discusses the technical progress of a US Department of Energy Innovative Clean Coal Technology project demonstrating advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The primary objective of the demonstration is to determine the long-term performance of advanced overfire air and low NO{sub x} burners applied in a stepwise fashion to a 500 MW boiler. A 50 percent NO{sub x} reduction target has been established for the project. The focus of this paper is to present the effects of excess oxygen level and burner settings on NO{sub x} emissions and unburned carbon levels and recent results from the phase of the project when low NO{sub x} burners were used in conjunction with advanced overfire air.

  10. Principles of operation and first clinical results using the picosecond IR laser

    NASA Astrophysics Data System (ADS)

    Bille, Josef F.; Klancnik, Edward G.; Niemz, M. H.

    1992-08-01

    A laser system is described that offers manifold applications in ophthalmic surgery. The Nd:YLF solid-state laser emits at a wavelength of 1.053 micrometers . With pulse durations of 40 psec less energy is required to obtain optical breakdown compared to nanosecond lasers. The lower pulse energy allows a substantial confinement of the laser-tissue interaction. With a highly sophisticated delivery system eye movements can be tracked during surgery and a precise placement of the laser focus can be achieved. The high transmission coefficient of ocular structures for wavelengths around 1 micrometers enables the Nd:YLF laser to perform several internal eye surgeries such as cataract fragmentation, intrastromal refractive surgery, internal sclerostomy, or iridotomy. First clinical results of some of these procedures are summarized.

  11. Damping measurements from an operating wind turbine: Preliminary results and procedures

    SciTech Connect

    James, G.H.; Carne, T.G.

    1992-12-31

    The Natural Excitation Technique (NEXT) extracts modal parameters from structures undergoing some natural excitation in which no measure of the excitation force is available. Preliminary damping results are presented for the first blade flatwise modes of the Sandia/DOE 34-m Test Bed (a Vertical Axis Wind Turbine) as a function of both wind speed and tip speed ratio. The current data set is to sparse to show a trend between damping and wind speed, however a trend of higher damping for higher tip speed ratio is apparent. An estimate of the uncertainty of the data is provided. Several improvements to NEXT have been added and are discussed in this paper. These improvements include: the use of a single software environment, the addition of the complex mode indicator function, the partial removal of harmonics, time and frequency domain cross-correlation function calculation, windowing, variable ensemble size capability, filtering and data decimation, and visual convergence checking.

  12. Damping measurements from an operating wind turbine: Preliminary results and procedures

    SciTech Connect

    James, G.H.; Carne, T.G.

    1992-01-01

    The Natural Excitation Technique (NEXT) extracts modal parameters from structures undergoing some natural excitation in which no measure of the excitation force is available. Preliminary damping results are presented for the first blade flatwise modes of the Sandia/DOE 34-m Test Bed (a Vertical Axis Wind Turbine) as a function of both wind speed and tip speed ratio. The current data set is to sparse to show a trend between damping and wind speed, however a trend of higher damping for higher tip speed ratio is apparent. An estimate of the uncertainty of the data is provided. Several improvements to NEXT have been added and are discussed in this paper. These improvements include: the use of a single software environment, the addition of the complex mode indicator function, the partial removal of harmonics, time and frequency domain cross-correlation function calculation, windowing, variable ensemble size capability, filtering and data decimation, and visual convergence checking.

  13. Overview of Results from the Cassini Magnetospheric Imaging Instrument (MIMI) During the First Year of Operations

    NASA Technical Reports Server (NTRS)

    Krimigis, S. M.; Mitchell, D. G.; Hamilton, D. C.; Krupp, N.; Livi, S.; Roelof, E. C.; Dandouras, J.; Mauk, B. H.; Brandt, J. P.; Paranicas, C.

    2005-01-01

    The MIMI investigation comprises three sensors covering the indicated energy ranges: the Ion and Neutral Camera (INCA) -- 7 keV/nuc 3 Mev) and protons (1.6 < E < 160 Mev) from the back end of the dual field-of-view telescope. The Saturn observation sequences began in January, 2004 and culminated in Saturn Orbit Insertion on July 1, 2004. The MIMI sensors observed substantial activity in interplanetary space for several months prior to SOI, including several interplanetary shocks associated with corotating interaction regions, numerous increases most likely originating from particle streams in the vicinity of the Saturnian bow shock and energetic neutral atoms (ENA) emanating from Saturn s magnetosphere. Results following SOI revealed: a dynamical magnetosphere with a day-night asymmetry and an 11-hour periodicity; several water-product ions (O+, OH+, H2O+), but little N+; inferred quantities of neutral gas sufficient to cause major losses in the trapped ions and electrons in the middle and inner magnetosphere; a Titan exosphere that is a copious source of ENA; INCA imaging through ENA has also revealed a previously unknown radiation belt residing inward of the D-ring that is most likely the result of double charge-exchange between the main radiation belt and the upper layers of Saturn s exosphere. Finally, there is ample evidence for the presence of substorm-like injections of plasma that subsequently corotates for a number of days before dissipating on the night-side magnetotail. The observations will be presented and discussed in the context of current theoretical models.

  14. Greenhouse gases observation from space -initial operation and calibration results of TANSO on GOSAT- (Invited)

    NASA Astrophysics Data System (ADS)

    Kuze, A.; Shiomi, K.; Suto, H.; Nakajima, M.

    2009-12-01

    The Greenhouse gases Observing SATellite (GOSAT) observes carbon dioxide (CO2) and methane (CH4) globally from space. It is a joint project of Japan Aerospace Exploration Agency (JAXA), Ministry of the Environment (MOE) and National Institute for Environmental Studies (NIES). GOSAT was launched on January 23, 2009 from Tanegashima Space Center and placed in a 666 km sun-synchronous orbit of 12:48 local time, with an inclination angle of 98 deg. There are two instruments: the Thermal And Near infrared Sensor for carbon Observation Fourier-Transform Spectrometer (TANSO-FTS) detects gas absorption spectra of Short Wave InfraRed (SWIR) reflected on the earth's surface as well as of Thermal InfraRed (TIR) radiated from the ground and the atmosphere. TANSO-FTS is capable of detecting wide spectral coverage; three narrow bands (0.76, 1.6, and 2μm) and a wide band (5.5-14.3 μm) with 0.27 cm-1 spectral resolution. The TANSO Cloud and Aerosol Imager (TANSO-CAI) is a radiometer of ultraviolet (UV), visible, and SWIR to detect cloud and aerosol interference. TANSO-FTS and CAI acquire global data every three days. For the first six months after the launch, on-orbit function, performance, calibration, and validation have been checked-out. The presentation includes instrument design, pre-launch test results, observation plan, onboard calibration schemes, and the initial on-orbit results of radiometric, geometric and spectroscopic performances. The data processing on the ground is also presented.

  15. First Look at Landsat-7 Mission Performance: Technical and Operational Results to Date

    NASA Technical Reports Server (NTRS)

    Williams, Darrel L.; Irons, James R.; Barker, John L.; Markham, Brian; Pedelty, Jeffrey A.

    1999-01-01

    A primary goal of the current Landsat-7 mission, launched on April 15, 1999, is to acquire and refresh on a seasonal basis, calibrated ata sets of multispectral digital imagery of the landmass of the Earth The Enhanced Thematic Mapper Plus (ETM+) imager flown on Landsat-7 provides ground spatial resolutions in the panchromatic, reflective and emissive bands of 15, 30 and 60 meters, respectively, for a nominal scene 183 km wide by 170 km long. This mission not only builds on the invaluable 27-year continuous archive of thematic images of the Earth provided by previous Landsat satellites, it also inaugurates a new era of robust data acquisition with an emphasis on global change science. The newly developed Long Term Acquisition Plan (LTAP) is being used to optimize the systematic collection of data from all parts of the globe, populating the U.S.-held archive at the USGS EROS Data Center (EDC) with over 90,000 Landsat scene per year . An additional 73,000 Images are expected to be acquired each year by several international ground stations, for a total downlink of Landsat7 data in excess of 100 terabytes per year. Nearly 20,000 scan of Landsat-7 ETM+ data have already been acquired in the first 100 days of the mission. Early results derived from assessments of the ETM+ instrument, the spacecraft, and the ground processing systems indicate that the image quality is outstanding, clearly the best ever provided by any Landsat mission. Sensor radiometric background stability after the first 100 days in orbit is approximately 0.1 percent. Stability of the Full Aperture Solar Calibrator is approximately 0.3 percent, and mid-scale per pixel noise is approximately 0.6 percent. A ground processing system has been implemented at EDC which is capable of capturing, processing and archiving 250 Landsat scenes 9 per day, and delivering 100 scene products to seems each day. The cost of a systematically-processed Level 1 product has been dropped dramatically to $600, end there is no

  16. 26 CFR 1.66-4 - Request for relief from the Federal income tax liability resulting from the operation of...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 26 Internal Revenue 2 2012-04-01 2012-04-01 false Request for relief from the Federal income tax liability resulting from the operation of community property law. 1.66-4 Section 1.66-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Definition of Gross...

  17. 26 CFR 1.66-4 - Request for relief from the Federal income tax liability resulting from the operation of...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 26 Internal Revenue 2 2014-04-01 2014-04-01 false Request for relief from the Federal income tax liability resulting from the operation of community property law. 1.66-4 Section 1.66-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Definition of Gross...

  18. 26 CFR 1.66-4 - Request for relief from the Federal income tax liability resulting from the operation of...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 2 2011-04-01 2011-04-01 false Request for relief from the Federal income tax liability resulting from the operation of community property law. 1.66-4 Section 1.66-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Definition of Gross...

  19. Development of a wind energy converter and investigation of its operational function. Part 4: Test setup and results of measurement

    NASA Astrophysics Data System (ADS)

    Armbrust, S.; Molly, J. P.

    1982-12-01

    Measurements made during test operations at the MODA.10 plant as well as at a 25 years old 6 kW wind energy converter are presented. The test arrangements, measurement results of both wind energy converters, and the experience gained are described.

  20. Results of Scoping Tests Examining the Effects of Gilsulate, Aluminum Silicate and Defoamers on the Operation of Conductivity Level Probes

    SciTech Connect

    Swingle, R.F.

    1999-02-17

    Scoping tests have been completed examining the effects of Gilsulate, sodium aluminum silicate, and some organic materials on the operation of tank level conductivity probes. This report documents the results of scoping studies completed to examine the effect of those materials on conductivity probes.

  1. OzDES multifibre spectroscopy for the Dark Energy Survey: First-year operation and results

    SciTech Connect

    Yuan, Fang

    2015-07-29

    The Australian Dark Energy Survey (OzDES) is a five-year, 100-night, spectroscopic survey on the Anglo-Australian Telescope, whose primary aim is to measure redshifts of approximately 2500 Type Ia supernovae host galaxies over the redshift range 0.1 < z < 1.2, and derive reverberation-mapped black hole masses for approximately 500 active galactic nuclei and quasars over 0.3 < z < 4.5. This treasure trove of data forms a major part of the spectroscopic follow-up for the Dark Energy Survey for which we are also targeting cluster galaxies, radio galaxies, strong lenses, and unidentified transients, as well as measuring luminous red galaxies and emission line galaxies to help calibrate photometric redshifts. Here, we present an overview of the OzDES programme and our first-year results. Between 2012 December and 2013 December, we observed over 10 000 objects and measured more than 6 000 redshifts. Our strategy of retargeting faint objects across many observing runs has allowed us to measure redshifts for galaxies as faint as mr = 25 mag. We outline our target selection and observing strategy, quantify the redshift success rate for different types of targets, and discuss the implications for our main science goals. In conclusion, we highlight a few interesting objects as examples of the fortuitous yet not totally unexpected discoveries that can come from such a large spectroscopic survey.

  2. OzDES multifibre spectroscopy for the Dark Energy Survey: First-year operation and results

    DOE PAGESBeta

    Yuan, Fang

    2015-07-29

    The Australian Dark Energy Survey (OzDES) is a five-year, 100-night, spectroscopic survey on the Anglo-Australian Telescope, whose primary aim is to measure redshifts of approximately 2500 Type Ia supernovae host galaxies over the redshift range 0.1 < z < 1.2, and derive reverberation-mapped black hole masses for approximately 500 active galactic nuclei and quasars over 0.3 < z < 4.5. This treasure trove of data forms a major part of the spectroscopic follow-up for the Dark Energy Survey for which we are also targeting cluster galaxies, radio galaxies, strong lenses, and unidentified transients, as well as measuring luminous red galaxiesmore » and emission line galaxies to help calibrate photometric redshifts. Here, we present an overview of the OzDES programme and our first-year results. Between 2012 December and 2013 December, we observed over 10 000 objects and measured more than 6 000 redshifts. Our strategy of retargeting faint objects across many observing runs has allowed us to measure redshifts for galaxies as faint as mr = 25 mag. We outline our target selection and observing strategy, quantify the redshift success rate for different types of targets, and discuss the implications for our main science goals. In conclusion, we highlight a few interesting objects as examples of the fortuitous yet not totally unexpected discoveries that can come from such a large spectroscopic survey.« less

  3. OzDES multifibre spectroscopy for the Dark Energy Survey: first-year operation and results

    NASA Astrophysics Data System (ADS)

    Yuan, Fang; Lidman, C.; Davis, T. M.; Childress, M.; Abdalla, F. B.; Banerji, M.; Buckley-Geer, E.; Carnero Rosell, A.; Carollo, D.; Castander, F. J.; D'Andrea, C. B.; Diehl, H. T.; Cunha, C. E.; Foley, R. J.; Frieman, J.; Glazebrook, K.; Gschwend, J.; Hinton, S.; Jouvel, S.; Kessler, R.; Kim, A. G.; King, A. L.; Kuehn, K.; Kuhlmann, S.; Lewis, G. F.; Lin, H.; Martini, P.; McMahon, R. G.; Mould, J.; Nichol, R. C.; Norris, R. P.; O'Neill, C. R.; Ostrovski, F.; Papadopoulos, A.; Parkinson, D.; Reed, S.; Romer, A. K.; Rooney, P. J.; Rozo, E.; Rykoff, E. S.; Sako, M.; Scalzo, R.; Schmidt, B. P.; Scolnic, D.; Seymour, N.; Sharp, R.; Sobreira, F.; Sullivan, M.; Thomas, R. C.; Tucker, D.; Uddin, S. A.; Wechsler, R. H.; Wester, W.; Wilcox, H.; Zhang, B.; Abbott, T.; Allam, S.; Bauer, A. H.; Benoit-Lévy, A.; Bertin, E.; Brooks, D.; Burke, D. L.; Carrasco Kind, M.; Covarrubias, R.; Crocce, M.; da Costa, L. N.; DePoy, D. L.; Desai, S.; Doel, P.; Eifler, T. F.; Evrard, A. E.; Fausti Neto, A.; Flaugher, B.; Fosalba, P.; Gaztanaga, E.; Gerdes, D.; Gruen, D.; Gruendl, R. A.; Honscheid, K.; James, D.; Kuropatkin, N.; Lahav, O.; Li, T. S.; Maia, M. A. G.; Makler, M.; Marshall, J.; Miller, C. J.; Miquel, R.; Ogando, R.; Plazas, A. A.; Roodman, A.; Sanchez, E.; Scarpine, V.; Schubnell, M.; Sevilla-Noarbe, I.; Smith, R. C.; Soares-Santos, M.; Suchyta, E.; Swanson, M. E. C.; Tarle, G.; Thaler, J.; Walker, A. R.

    2015-09-01

    The Australian Dark Energy Survey (OzDES) is a five-year, 100-night, spectroscopic survey on the Anglo-Australian Telescope, whose primary aim is to measure redshifts of approximately 2500 Type Ia supernovae host galaxies over the redshift range 0.1 < z < 1.2, and derive reverberation-mapped black hole masses for approximately 500 active galactic nuclei and quasars over 0.3 < z < 4.5. This treasure trove of data forms a major part of the spectroscopic follow-up for the Dark Energy Survey for which we are also targeting cluster galaxies, radio galaxies, strong lenses, and unidentified transients, as well as measuring luminous red galaxies and emission line galaxies to help calibrate photometric redshifts. Here, we present an overview of the OzDES programme and our first-year results. Between 2012 December and 2013 December, we observed over 10 000 objects and measured more than 6 000 redshifts. Our strategy of retargeting faint objects across many observing runs has allowed us to measure redshifts for galaxies as faint as mr = 25 mag. We outline our target selection and observing strategy, quantify the redshift success rate for different types of targets, and discuss the implications for our main science goals. Finally, we highlight a few interesting objects as examples of the fortuitous yet not totally unexpected discoveries that can come from such a large spectroscopic survey.

  4. From design through operations-Results from new construction performance contract and beyond

    SciTech Connect

    Motegi, Naoya; Piette, Mary Ann; Wentworth, Scott

    2002-05-17

    As part of the High Performance Commercial Building Systems program, LBNL has been working with the City of Oakland to understand the ongoing performance of the Oakland Administration Buildings. The primary objective of this research is to understand the performance targets and ongoing performance of two buildings that were the subject of a new construction performance contract. Secondary objectives include examining the building performance information systems developed as part of the new construction performance contract and evaluating the role of the energy management and control system (EMCS) as a data acquisition tool to provide recommendations for future new construction projects. We examine the results of the performance contract in detail, and provide additional performance metrics that go beyond what was required in the performance contract. We found that the energy cost intensities (ECI) linked to the project ranged from $1.08/ft{sup 2} to $1.44/ft{sup 2}. Changes in floor area, energy costs, rate schedules, and energy use complicate the evaluation of the performance because of the lack of tracking of underlying data and assumptions. Overall, Oakland has two large office buildings with relatively low-energy use (50 kBtu/ft{sup 2}-yr site electricity and gas use). We compare this energy-use intensity with a number of related benchmarks. Additional end-use, HVAC performance, and diagnostics data are discussed.

  5. The fallacy of coverage: uncovering disparities to improve immunization rates through evidence. Results from the Canadian International Immunization Initiative Phase 2 - Operational Research Grants.

    PubMed

    Mhatre, Sharmila L; Schryer-Roy, Anne-Marie

    2009-01-01

    Immunization can and does save lives. However, the presence of vaccines does not easily translate into every child being vaccinated, and this is what the studies in this journal supplement reveal. From South Asia to West Africa,the evidence presented here reveals what we are calling the fallacy of coverage, going beyond uncovering the real vaccination rates to providing evidence on the reasons for the lack of effective coverage.The evidence for the fallacy of coverage is part of an operational research program entitled the Canadian International Immunization Initiative Phase 2 (CIII2). Through a competitive peer review process, six research grants were awarded to increase access to and enhance immunization services. This journal supplement provides a forum for the presentation of the results of five of the six studies.The story of the fallacy of coverage is made up of five theme areas of evidence - timeliness of immunization, social and gender inequities, vaccine efficacy, understanding demand side issues to tailor interventions, and national data sets masking actual district level coverage rates - that reveal the discrepancies in immunization coverage rates and the reasons behind these discrepancies. As part of the story, and to turn around the fallacy of coverage, the studies also provide proof of effective and locally relevant solutions.Policies and funding, while keeping an eye on future diseases, clearly need to maintain and increase support to address existing vaccine-preventable diseases to increase coverage such that by 2015 we can achieve 90% national vaccination coverage and reach the MDG of reducing mortality rates among children under five by two-thirds.The results from the operational research grants of the CIII2 offer some answers on how to reach this goal by demonstrating how locally generated evidence can inform immunization strategies to ensure that children who need to get vaccinated will get vaccinated, and vaccinated on time. PMID:19828053

  6. Operational TanDEM-X DEM calibration and first validation results

    NASA Astrophysics Data System (ADS)

    Gruber, Astrid; Wessel, Birgit; Huber, Martin; Roth, Achim

    2012-09-01

    In June 2010, the German TanDEM-X satellite was launched. Together with its twin satellite TerraSAR-X it flies in a close formation enabling single-pass SAR interferometry. The primary goal of the TanDEM-X mission is the derivation of a global digital elevation model (DEM) with unprecedented global accuracies of 10 m in absolute and 2 m in relative height. A significant calibration effort is required to achieve this high quality world-wide. In spite of an intensive instrument calibration and a highly accurate orbit and baseline determination, some systematic height errors like offsets and tilts in the order of some meters remain in the interferometric DEMs and have to be determined and removed during the TanDEM-X DEM calibration. The objective of this article is the presentation of an approach for the estimation of correction parameters for remaining systematic height errors applicable to interferometric height models. The approach is based on a least-squares block adjustment using the elevation of ICESat GLA 14 data as ground control points and connecting points of adjacent, overlapping DEMs as tie-points. In the first part its implementation in DLR's ground segment is outlined. In the second part the approach is applied and validated for two of the first TanDEM-X DEM test sites. Therefore, independent reference data, in particular high resolution reference DEMs and GPS tracks, are used. The results show that the absolute height errors of the TanDEM-X DEM are small in these cases, mostly in the order of 1-2 m. An additional benefit of the proposed block adjustment method is that it improves the relative accuracy of adjacent DEMs.

  7. Results of a survey of natural gas transmission companies operating continuous emission monitoring systems. Topical report, January-June 1994

    SciTech Connect

    1994-10-01

    A summary is presented to the results of a survey of continuous emission monitoring (CEM) systems operating on reciprocating engines and turbines of gas transmission companies. For this survey, three natural gas transmission companies were visited. Information on various aspects of CEM systems within the industry was gathered. It included characteristics of emission sources with emission reduction techniques where applied; CEM system outdoor shelters; monitoring techniques; costs; installation and startup; personnel training; operations and maintenance; performance evaluations and quality assurance; and data acquisition systems. The survey finds that the industry`s experience with CEM systems remains limited. Some recommendations are presented for the future, when the use of CEM systems may increase.

  8. Experimental design, operation, and results of a 4 kW high temperature steam electrolysis experiment

    SciTech Connect

    Zhang, Xiaoyu; O'Brien, James E.; Tao, Greg; Zhou, Can; Housley, Gregory K.

    2015-08-06

    High temperature steam electrolysis (HTSE) is a promising technology for large-scale hydrogen production. However, research on HTSE performance above the kW level is limited. This paper presents the results of 4 kW HTSE long-term test completed in a multi-kW test facility recently developed at the Idaho National Laboratory (INL). The 4 kW HTSE unit included two solid oxide electrolysis stacks operating in parallel, each of which included 40 electrode-supported planar cells. A current density of 0.41 A/cm2 was used for the long-term operation, resulting in a hydrogen production rate about 25 slpm. A demonstration of 920 hours stable operation was achieved. The paper also includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. As a result, this successful demonstration of multi-kW scale HTSE unit will help to advance the technology toward near-term commercialization.

  9. Experimental design, operation, and results of a 4 kW high temperature steam electrolysis experiment

    DOE PAGESBeta

    Zhang, Xiaoyu; O'Brien, James E.; Tao, Greg; Zhou, Can; Housley, Gregory K.

    2015-08-06

    High temperature steam electrolysis (HTSE) is a promising technology for large-scale hydrogen production. However, research on HTSE performance above the kW level is limited. This paper presents the results of 4 kW HTSE long-term test completed in a multi-kW test facility recently developed at the Idaho National Laboratory (INL). The 4 kW HTSE unit included two solid oxide electrolysis stacks operating in parallel, each of which included 40 electrode-supported planar cells. A current density of 0.41 A/cm2 was used for the long-term operation, resulting in a hydrogen production rate about 25 slpm. A demonstration of 920 hours stable operation wasmore » achieved. The paper also includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. As a result, this successful demonstration of multi-kW scale HTSE unit will help to advance the technology toward near-term commercialization.« less

  10. Results of Continuous Load Cell Monitoring Field Trial for UF6 Withdrawals at an Operating Industrial Plant

    SciTech Connect

    Krichinsky, Alan M; Bell, Lisa S; Conchewski, Curtis A; Peters, Benjamin R; Pickett, Chris A; Richardson, Dave; Rowe, Nathan C; Younkin, James R

    2010-01-01

    Continuous load cell monitoring (CLCM) has been implemented and tested for use as a safeguards tool during a 2009 field trial in an operating UF6 transfer facility. The transfer facility is part of the Portsmouth Gaseous Diffusion Plant in Piketon, Ohio, operated by the United States Enrichment Corporation. During the field trial, two process scales for UF{sub 6} cylinders were continuously monitored for a 6-month period as cylinders were being filled. The collected CLCM data were used in testing an event processor serving as a filter for highlighting measurements representing significant operational activities that are important in verifying declared operations. The collection of CLCM data, coupled with rules-based event processing, can provide inspectors with knowledge of a facility's feed and withdrawal activities occurring between site visits. Such process knowledge promises to enhance the effectiveness of safeguards by enabling inspectors to quantitatively compare declared activities directly with process measurements. Selected results of the field trial and event processing will be presented in the context of their value to an independent inspector and a facility operator.

  11. Application of fuzzy logic-neural network based reinforcement learning to proximity and docking operations: Attitude control results

    NASA Technical Reports Server (NTRS)

    Jani, Yashvant

    1992-01-01

    As part of the RICIS activity, the reinforcement learning techniques developed at Ames Research Center are being applied to proximity and docking operations using the Shuttle and Solar Max satellite simulation. This activity is carried out in the software technology laboratory utilizing the Orbital Operations Simulator (OOS). This report is deliverable D2 Altitude Control Results and provides the status of the project after four months of activities and outlines the future plans. In section 2 we describe the Fuzzy-Learner system for the attitude control functions. In section 3, we provide the description of test cases and results in a chronological order. In section 4, we have summarized our results and conclusions. Our future plans and recommendations are provided in section 5.

  12. Improved PFB operations: 400-hour turbine test results. [coal combustion products and hot corrosion in gas turbines

    NASA Technical Reports Server (NTRS)

    Rollbuhler, R. J.; Benford, S. M.; Zellars, G. R.

    1980-01-01

    A pressurized fluidized bed (PFB) coal-burning reactor was used to provide hot effluent gases for operation of a small gas turbine. Preliminary tests determined the optimum operating conditions that would result in minimum bed particle carryover in the combustion gases. Solids were removed from the gases before they could be transported into the test turbine by use of a modified two stage cyclone separator. Design changes and refined operation procedures resulted in a significant decrease in particle carryover, from 2800 to 93 ppm (1.5 to 0.05 grains/std cu ft), with minimal drop in gas temperature and pressure. The achievement of stable burn conditions and low solids loadings made possible a 400 hr test of small superalloy rotor, 15 cm (6 in.) in diameter, operating in the effluent. Blades removed and examined metallographically after 200 hr exhibited accelerated oxidation over most of the blade surface, with subsurface alumina penetration to 20 micron m. After 400 hours, average erosion loss was about 25 micron m (1 mil). Sulfide particles, indicating hot corrosion, were present in depletion zones, and their presence corresponded in general to the areas of adherent solids deposit. Sulfidation appears to be a materials problem equal in importance to erosion.

  13. Actualities and Perspectives in Neurosurgery

    PubMed Central

    Iencean, SM; Brehar, FM

    2008-01-01

    In the field of neurosurgery, like in other surgical specialties, the last decades have brought major achievements. The series of revolutionary discoveries has started during the last century in the fifties, with stereotactic radiosurgery, then continued with the implementation of operative microscope (during the seventies), the endovascular embolisation in the nineties and finally with the major improvement in robotic neurosurgery and molecular neurosurgery at the beginning of this century. The major innovation has been brought not only in the field of therapeutical measures but also in the field of neuro– imaging. Thus, the modern MRI with more than 3 Tesla, can reveal to the neurosurgeon the most intimate structures of the nervous system. Several important areas in neurosurgery like: vascular neurosurgery, functional neurosurgery and brain tumors pathology, benefit from the modern technology and from the latest discoveries from genetic and molecular biology. In conclusion, summarizing the discoveries of the last decade, we emphasize that the related areas like genetics, molecular biology, computer technology become more and more important in the future progress of the neurosurgery. PMID:20108475

  14. Fault diagnosis using a diagnostic shell and its verification results by connecting to an operator training simulator

    SciTech Connect

    Kobayashi, T.; Moridera, D.; Komai, K.; Fukui, S.; Matsumoto, K.

    1995-02-01

    This paper describes a fault diagnostic system using a diagnostic shell, MELDASH, and results that confirm its effectiveness. The diagnostic shell that reflects and makes use of the nature of model-based diagnosis is developed to overcome the drawbacks of methods that depend on operator knowledge. A high-performance fault diagnostic system is constructed simply by adding an application model to the diagnostic shell. A prototype system is verified by connecting it to an operator training simulator. It is able to make a proper diagnosis in 79 difficult fault cases. Verification results shows that the prototype system has sufficient accuracy. The authors confirm the effectiveness of this fault diagnostic method for future energy management systems.

  15. Extra-articular scapular fractures: comparison of theoretical and actual treatment

    PubMed Central

    Brandsema, Berdien; Neuhaus, Valentin; Gradl, Gertraud

    2015-01-01

    Background Discrete radiographic thresholds of scapular fracture deformity proposed as a guide for when to utilize operative treatment are a matter of debate. The purpose of the present study was to determine how many patients would have received operative treatment according to these criteria and how many actually received operative treatment. Methods Three hundred and thirty patients with an extra-articular fracture of the scapula at two level 1 trauma centers were retrospectively analyzed. Glenopolar angle, translation, angulation and medial/lateral displacement were measured on computed tomogaphy scans or radiographs to determine the theoretical operative treatment recommendation according to Cole’s criteria. Results Sixty-two patients (19%) had one or more radiographic indications for operative treatment, half of them had more than 20 mm of lateral displacement, and one fourth of them had substantial translation. No patients had operative treatment of the scapular body. Two patients had operative treatment of an acromion fracture, neither of which met radiographic criteria for surgery. Conclusions At least in our centres, there is a striking discrepancy between theoretical and actual recommendations for surgery. There is clearly a need for more research to determine whether patients are being undertreated or whether the guidelines are too stringent. PMID:27582994

  16. Flight Deck Surface Trajectory-based Operations (STBO): Results of Piloted Simulations and Implications for Concepts of Operation (ConOps)

    NASA Technical Reports Server (NTRS)

    Foyle, David C.; Hooey, Becky L.; Bakowski, Deborah L.

    2013-01-01

    The results offour piloted medium-fidelity simulations investigating flight deck surface trajectory-based operations (STBO) will be reviewed. In these flight deck STBO simulations, commercial transport pilots were given taxi clearances with time and/or speed components and required to taxi to the departing runway or an intermediate traffic intersection. Under a variety of concept of operations (ConOps) and flight deck information conditions, pilots' ability to taxi in compliance with the required time of arrival (RTA) at the designated airport location was measured. ConOps and flight deck information conditions explored included: Availability of taxi clearance speed and elapsed time information; Intermediate RTAs at intermediate time constraint points (e.g., intersection traffic flow points); STBO taxi clearances via ATC voice speed commands or datal ink; and, Availability of flight deck display algorithms to reduce STBO RTA error. Flight Deck Implications. Pilot RTA conformance for STBO clearances, in the form of ATC taxi clearances with associated speed requirements, was found to be relatively poor, unless the pilot is required to follow a precise speed and acceleration/deceleration profile. However, following such a precise speed profile results in inordinate head-down tracking of current ground speed, leading to potentially unsafe operations. Mitigating these results, and providing good taxi RTA performance without the associated safety issues, is a flight deck avionics or electronic flight bag (EFB) solution. Such a solution enables pilots to meet the taxi route RTA without moment-by-moment tracking of ground speed. An avionics or EFB "error-nulling" algorithm allows the pilot to view the STBO information when the pilot determines it is necessary and when workload alloys, thus enabling the pilot to spread his/her attention appropriately and strategically on aircraft separation airport navigation, and the many other flight deck tasks concurrently required

  17. Requirements for Computer Based-Procedures for Nuclear Power Plant Field Operators Results from a Qualitative Study

    SciTech Connect

    Katya Le Blanc; Johanna Oxstrand

    2012-05-01

    Although computer-based procedures (CBPs) have been investigated as a way to enhance operator performance on procedural tasks in the nuclear industry for almost thirty years, they are not currently widely deployed at United States utilities. One of the barriers to the wide scale deployment of CBPs is the lack of operational experience with CBPs that could serve as a sound basis for justifying the use of CBPs for nuclear utilities. Utilities are hesitant to adopt CBPs because of concern over potential costs of implementation, and concern over regulatory approval. Regulators require a sound technical basis for the use of any procedure at the utilities; without operating experience to support the use CBPs, it is difficult to establish such a technical basis. In an effort to begin the process of developing a technical basis for CBPs, researchers at Idaho National Laboratory are partnering with industry to explore CBPs with the objective of defining requirements for CBPs and developing an industry-wide vision and path forward for the use of CBPs. This paper describes the results from a qualitative study aimed at defining requirements for CBPs to be used by field operators and maintenance technicians.

  18. Design, operational experiences and beam results obtained with the SNS H- ion source and LEBT at Berkeley Lab

    SciTech Connect

    Keller, R.; Thomae, R.; Stockli, M.; Welton, R.

    2002-04-15

    The ion source and Low-Energy Transport (LEBT) system that will provide H{sup -} ion beams to the Spallation Neutron Source (SNS)** Front End and the accelerator chain have been developed into a mature unit that fully satisfies the operational requirements through the commissioning and early operating phases of SNS. Compared to the early R&D version, many features of the ion source have been improved, and reliable operation at 6% duty factor has been achieved producing beam currents in the 35-mA range and above. LEBT operation proved that the purely electrostatic focusing principle is well suited to inject the ion beam into the RFQ accelerator, including the steering and pre-chopping functions. This paper will discuss the latest design features of the ion source and LEBT, give performance data for the integrated system, and report on commissioning results obtained with the SNS RFQ and Medium-Energy Beam Transport (MEBT) system. Prospects for further improvements will be outlined in concluding remarks.

  19. Experiment Description and Results for Arrival Operations Using Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR)

    NASA Technical Reports Server (NTRS)

    Baxley, Brian T.; Murdoch, Jennifer L.; Swieringa, Kurt A.; Barmore, Bryan E.; Capron, William R.; Hubbs, Clay E.; Shay, Richard F.; Abbott, Terence S.

    2013-01-01

    The predicted increase in the number of commercial aircraft operations creates a need for improved operational efficiency. Two areas believed to offer increases in aircraft efficiency are optimized profile descents and dependent parallel runway operations. Using Flight deck Interval Management (FIM) software and procedures during these operations, flight crews can achieve by the runway threshold an interval assigned by air traffic control (ATC) behind the preceding aircraft that maximizes runway throughput while minimizing additional fuel consumption and pilot workload. This document describes an experiment where 24 pilots flew arrivals into the Dallas Fort-Worth terminal environment using one of three simulators at NASA?s Langley Research Center. Results indicate that pilots delivered their aircraft to the runway threshold within +/- 3.5 seconds of their assigned time interval, and reported low workload levels. In general, pilots found the FIM concept, procedures, speeds, and interface acceptable. Analysis of the time error and FIM speed changes as a function of arrival stream position suggest the spacing algorithm generates stable behavior while in the presence of continuous (wind) or impulse (offset) error. Concerns reported included multiple speed changes within a short time period, and an airspeed increase followed shortly by an airspeed decrease.

  20. North Carolina’s Operation Medicine Drop: Results From One of the Nation’s Largest Drug Disposal Programs

    PubMed Central

    Fleming, Eleanor; Proescholdbell, Scott; Sachdeva, Nidhi; Alexandridis, Apostolos A.; Margolis, Lewis; Ransdell, Kelly

    2016-01-01

    INTRODUCTION In 2013, a total of 1,085 North Carolina residents died due to unintentional poisoning; 91% of these deaths were attributed to medications or drugs (over-the-counter, prescription, or illicit). Proper disposal of unused, unneeded, and/or expired medications is an essential part of preventing these unintentional deaths, as well as averting the other adverse consequences of these drugs on the environment and population health. METHODS Operation Medicine Drop is a medication take-back program coordinated by Safe Kids North Carolina, a county-level, coalition-based injury prevention organization. The Operation Medicine Drop program and event registration system were used to review and validate the number of events, the counties where the events were held, and the number of unit doses (pills) collected from March 2010 to June 2014. SAS version 9.4 was used to generate basic counts and frequencies of events and doses, and ArcGIS version 10.0 was used to create the map. RESULTS From March 2010 to June 2014, Operation Medicine Drop held 1,395 events with 245 different participating law enforcement agencies in 91 counties in North Carolina, and it collected 69.6 million unit doses of medication. More than 60 local Safe Kids North Carolina community coalitions had participated as of June 2014. Every year, Operation Medicine Drop has witnessed increases in events, participating agencies, participating counties, and the number of doses collected. CONCLUSION Operation Medicine Drop is an excellent example of a successful and ongoing collaboration to improve public health. Medication take-back programs may play an important role in preventing future overdose deaths in North Carolina. PMID:26763245

  1. Analysis of post-operative pain patterns following total lumbar disc replacement: results from fluoroscopically guided spine infiltrations

    PubMed Central

    Korge, Andreas; Grochulla, Frank; Mehren, Christoph

    2007-01-01

    Although a variety of biomechanical laboratory investigations and radiological studies have highlighted the potential problems associated with total lumbar disc replacement (TDR), no previous study has performed a systematic clinical failure analysis. The aim of this study was to identify the post-operative pain sources, establish the incidence of post-operative pain patterns and investigate the effect on post-operative outcome with the help of fluoroscopically guided spine infiltrations in patients from an ongoing prospective study with ProDisc II. Patients who reported unsatisfactory results at any of the FU-examinations received fluoroscopically guided spine infiltrations as part of a semi-invasive diagnostic and conservative treatment program. Pain sources were identified in patients with reproducible (≥2×) significant (50–75%) or highly significant (75–100%) pain relief. Results were correlated with outcome parameters visual analogue scale (VAS), Oswestry disability index (ODI) and the subjective patient satisfaction rate. From a total of 175 operated patients with a mean follow-up (FU) of 29.3 months (range 12.2–74.9 months), n = 342 infiltrations were performed in n = 58 patients (33.1%) overall. Facet joint pain, predominantly at the index level (86.4%), was identified in n = 22 patients (12.6%). The sacroiliac joint was a similarly frequent cause of post-operative pain (n = 21, 12.0%). Pain from both structures influenced all outcome parameters negatively (P < 0.05). Patients with an early onset of pain (≤6 months) were 2–5× higher at risk of developing persisting complaints and unsatisfactory outcome at later FU-stages in comparison to the entire study cohort (P < 0.05). The level of TDR significantly influenced post-operative outcome. Best results were achieved for the TDRs above the lumbosacral junction at L4/5 (incidence of posterior joint pain 14.8%). Inferior outcome and a significantly higher incidence of posterior joint

  2. Analysis of post-operative pain patterns following total lumbar disc replacement: results from fluoroscopically guided spine infiltrations.

    PubMed

    Siepe, Christoph J; Korge, Andreas; Grochulla, Frank; Mehren, Christoph; Mayer, H Michael

    2008-01-01

    Although a variety of biomechanical laboratory investigations and radiological studies have highlighted the potential problems associated with total lumbar disc replacement (TDR), no previous study has performed a systematic clinical failure analysis. The aim of this study was to identify the post-operative pain sources, establish the incidence of post-operative pain patterns and investigate the effect on post-operative outcome with the help of fluoroscopically guided spine infiltrations in patients from an ongoing prospective study with ProDisc II. Patients who reported unsatisfactory results at any of the FU-examinations received fluoroscopically guided spine infiltrations as part of a semi-invasive diagnostic and conservative treatment program. Pain sources were identified in patients with reproducible (> or =2x) significant (50-75%) or highly significant (75-100%) pain relief. Results were correlated with outcome parameters visual analogue scale (VAS), Oswestry disability index (ODI) and the subjective patient satisfaction rate. From a total of 175 operated patients with a mean follow-up (FU) of 29.3 months (range 12.2-74.9 months), n = 342 infiltrations were performed in n = 58 patients (33.1%) overall. Facet joint pain, predominantly at the index level (86.4%), was identified in n = 22 patients (12.6%). The sacroiliac joint was a similarly frequent cause of post-operative pain (n = 21, 12.0%). Pain from both structures influenced all outcome parameters negatively (P < 0.05). Patients with an early onset of pain (< or =6 months) were 2-5x higher at risk of developing persisting complaints and unsatisfactory outcome at later FU-stages in comparison to the entire study cohort (P < 0.05). The level of TDR significantly influenced post-operative outcome. Best results were achieved for the TDRs above the lumbosacral junction at L4/5 (incidence of posterior joint pain 14.8%). Inferior outcome and a significantly higher incidence of posterior joint pain were observed

  3. The LANDSAT system operated in Brazil by CNPq/INPE - results obtained in the area of mapping and future perspectives

    NASA Technical Reports Server (NTRS)

    Dejesusparada, N. (Principal Investigator); Barbosa, M. N.

    1981-01-01

    The LANDSAT system, operated in the country by CNPg/INPE since 1973, systematically acquires, produces, and distributes both multispectral and panchromatic images obtained through remote sensing satellites to thousands of researchers and technicians involved in the natural resources survey. To cooperate in the solution of national problems, CNPq/INPE is developing efforts in the area of manipulation of those images with the objective of making them useful as planimetric bases for the simple revision of already published maps or for its utilization as basic material in regions not yet reliability mapped. The results obtained from performed tests are presented and the existing limitations are discussed. The new system purchased to handle data from the next series of LANDSAT as well as from MAPSAT and SPOT which will be in operation within the 80's decade, and are designed not only for natural resources survey but also for the solution of cartographic problems.

  4. Boehmite Actual Waste Dissolutions Studies

    SciTech Connect

    Snow, Lanee A.; Lumetta, Gregg J.; Fiskum, Sandra K.; Peterson, Reid A.

    2008-07-15

    The U.S. Department of Energy plans to vitrify approximately 60,000 metric tons of high-level waste (HLW) sludge from underground storage tanks at the Hanford Nuclear Reservation. To reduce the volume of HLW requiring treatment, a goal has been set to remove a significant quantity of the aluminum, which comprises nearly 70 percent of the sludge. Aluminum is found in the form of gibbsite, sodium aluminate and boehmite. Gibbsite and sodium aluminate can be easily dissolved by washing the waste stream with caustic. Boehmite, which comprises nearly half of the total aluminum, is more resistant to caustic dissolution and requires higher treatment temperatures and hydroxide concentrations. Samples were taken from four Hanford tanks and homogenized in order to give a sample that is representative of REDOX (Reduction Oxidation process for Pu recovery) sludge solids. Bench scale testing was performed on the homogenized waste to study the dissolution of boehmite. Dissolution was studied at three different hydroxide concentrations, with each concentration being run at three different temperatures. Samples were taken periodically over the 170 hour runs in order to determine leaching kinetics. Results of the dissolution studies and implications for the proposed processing of these wastes will be discussed.

  5. 40 CFR 63.5335 - How do I determine the actual HAP loss?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (CONTINUED) National Emission Standards for Hazardous Air Pollutants for Leather Finishing Operations... information and procedures you must use to determine the actual HAP loss from your leather finishing operation. By the fifteenth of each month, you must determine the actual HAP loss in pounds from your...

  6. STEAM REFORMING TECHNOLOGY DEMONSTRATION FOR THE DESTRUCTION OF ORGANICS ON ACTUAL DOE SAVANNAH RIVER SITE TANK 48H WASTE 9138

    SciTech Connect

    Burket, P

    2009-02-24

    This paper describes the design of the Bench-scale Steam Reformer (BSR); a processing unit for demonstrating steam reforming technology on actual radioactive waste [1]. It describes the operating conditions of the unit used for processing a sample of Savannah River Site (SRS) Tank 48H waste. Finally, it compares the results from processing the actual waste in the BSR to processing simulant waste in the BSR to processing simulant waste in a large pilot scale unit, the Fluidized Bed Steam Reformer (FBSR), operated at Hazen Research Inc. in Golden, CO. The purpose of this work was to prove that the actual waste reacted in the same manner as the simulant waste in order to validate the work performed in the pilot scale unit which could only use simulant waste.

  7. Implementation and Operational Research: Expedited Results Delivery Systems Using GPRS Technology Significantly Reduce Early Infant Diagnosis Test Turnaround Times.

    PubMed

    Deo, Sarang; Crea, Lindy; Quevedo, Jorge; Lehe, Jonathan; Vojnov, Lara; Peter, Trevor; Jani, Ilesh

    2015-09-01

    The objective of this study was to quantify the impact of a new technology to communicate the results of an infant HIV diagnostic test on test turnaround time and to quantify the association between late delivery of test results and patient loss to follow-up. We used data collected during a pilot implementation of Global Package Radio Service (GPRS) printers for communicating results in the early infant diagnosis program in Mozambique from 2008 through 2010. Our dataset comprised 1757 patient records, of which 767 were from before implementation and 990 from after implementation of expedited results delivery system. We used multivariate logistic regression model to determine the association between late result delivery (more than 30 days between sample collection and result delivery to the health facility) and the probability of result collection by the infant's caregiver. We used a sample selection model to determine the association between late result delivery to the facility and further delay in collection of results by the caregiver. The mean test turnaround time reduced from 68.13 to 41.05 days post-expedited results delivery system. Caregivers collected only 665 (37.8%) of the 1757 results. After controlling for confounders, the late delivery of results was associated with a reduction of approximately 18% (0.44 vs. 0.36; P < 0.01) in the probability of results collected by the caregivers (odds ratio = 0.67, P < 0.05). Late delivery of results was also associated with a further average increase in 20.91 days of delay in collection of results (P < 0.01). Early infant diagnosis program managers should further evaluate the cost-effectiveness of operational interventions (eg, GPRS printers) that reduce delays. PMID:26068719

  8. Factors Related to Self-Actualization.

    ERIC Educational Resources Information Center

    Hogan, H. Wayne; McWilliams, Jettie M.

    1978-01-01

    Provides data to further support the notions that females score higher in self-actualization measures and that self-actualization scores correlate inversely to the degree of undesirability individuals assign to their heights and weights. Finds that, contrary to predictions, greater androgyny was related to lower, not higher, self-actualization…

  9. [Clinical results of the treatment of chronic hematogenous osteomyelitis of the femur by operation. A series of 165 cases].

    PubMed

    Ziani, F; Daoud, A; Martini, M

    1992-01-01

    Between 1968 and 1987 the authors treated 165 cases of chronic haematogenous osteomyelitis of the femur by operation. The procedure used combined decompression, sequestrectomy and saucerization in 161 cases, and sequestrectomy alone in 4. Chemotherapy was used in association for between 10 and 60 days. Eleven patients, thought to be healed, were lost to follow-up after 4 months. The remainder were reviewed for between 4 and 252 months, 124 for more than one year. After the first operation 105 lesions (64%) healed completely, while 60 (36%) relapsed. Of these, 48 were treated by further operation and 12 by drainage of the abscess. Nine patients relapsed twice and there were 3 or more relapses in a further 9. When last seen, 147 lesions were healed and 18 had a permanent sinus. Special features in relation to the femur are discussed, including destructive lesions of the knee and hip joints, the high incidence of stiffness of the knee even in the absence of radiographic evidence of destruction (48.5%), and the danger of injuries to the femoral vessels when using an approach through a medial sinus. The frequency of occurrence of lesions on both medial and posterior aspects of the femur has led the authors to recommend definitive surgical approaches, especially the true postero-lateral and antero-medial routes. Unsatisfactory results after operation may be due to the difficulty in performing sequestrectomy in deep and extensive lesions, problems in undertaking adequate saucerization and the lack of muscle to fill the residual cavity. PMID:1428315

  10. Results of the Updated NASA Kennedy Space Center 50-MHz Doppler Radar Wind Profiler Operational Acceptance Test

    NASA Technical Reports Server (NTRS)

    Barbre', Robert E., Jr.; Deker, Ryan K.; Leahy, Frank B.; Huddleston, Lisa

    2016-01-01

    We present here the methodology and results of the Operational Acceptance Test (OAT) performed on the new Kennedy Space Center (KSC) 50-MHz Doppler Radar Wind Profiler (DRWP). On day-of-launch (DOL), space launch vehicle operators have used data from the DRWP to invalidate winds in prelaunch loads and trajectory assessments due to the DRWP's capability to quickly identify changes in the wind profile within a rapidly-changing wind environment. The previous DRWP has been replaced with a completely new system, which needs to undergo certification testing before being accepted for use in range operations. The new DRWP replaces the previous three-beam system made of coaxial cables and a copper wire ground plane with a four-beam system that uses Yagi antennae with enhanced beam steering capability. In addition, the new system contains updated user interface software while maintaining the same general capability as the previous system. The new DRWP continues to use the Median Filter First Guess (MFFG) algorithm to generate a wind profile from Doppler spectra at each range gate. DeTect (2015) contains further details on the upgrade. The OAT is a short-term test designed so that end users can utilize the new DRWP in a similar manner to the previous DRWP during mission operations at the Eastern Range in the midst of a long-term certification process. This paper describes the Marshall Space Flight Center Natural Environments Branch's (MSFC NE's) analyses to verify the quality and accuracy of the DRWP's meteorological data output as compared to the previous DRWP. Ultimately, each launch vehicle program has the responsibility to certify the system for their own use.

  11. Results of an Advanced Fan Stage Operating Over a Wide Range of Speed and Bypass Ratio. Part 2; Comparison of CFD and Experimental Results

    NASA Technical Reports Server (NTRS)

    Celestina, Mark L.; Suder, Kenneth L.; Kulkarni, Sameer

    2010-01-01

    NASA and GE teamed to design and build a 57 percent engine scaled fan stage for a Mach 4 variable cycle turbofan/ramjet engine for access to space with multipoint operations. This fan stage was tested in NASA's transonic compressor facility. The objectives of this test were to assess the aerodynamic and aero mechanic performance and operability characteristics of the fan stage over the entire range of engine operation including: 1) sea level static take-off; 2) transition over large swings in fan bypass ratio; 3) transition from turbofan to ramjet; and 4) fan wind-milling operation at high Mach flight conditions. This paper will focus on an assessment of APNASA, a multistage turbomachinery analysis code developed by NASA, to predict the fan stage performance and operability over a wide range of speeds (37 to 100 percent) and bypass ratios.

  12. Life Test Results for Water Heat Pipes Operating at 200 °C to 300 °C

    NASA Astrophysics Data System (ADS)

    Rosenfeld, John H.; Gernert, Nelson J.

    2008-01-01

    For lunar or planetary bases to be viable, a robust electric generating system will be required for powering the habitat. Water heat pipes offer an attractive solution for lunar base heat rejection, and would serve as a qualification for them on other long duration missions. Successful operation near the upper end of water operating range is a requirement for the application. Results are reported for life tests on water heat pipes that were operated at various temperatures between 200 °C and 300 °C. Tests were conducted on twenty three gravity-assisted water heat pipes. Eleven titanium/water heat pipes and ten Monel/water heat pipes were tested at temperatures above 200 °C. Two cupronickel heat pipes were also assembled and tested. Titanium alloys tested included CP-2 titanium, as well as two beta-titanium alloys, namely 15-3 and Nitinol alloys. Some of the titanium alloy life tests used wicks fabricated from CP-2 titanium screen or porous felt. Monel alloys tested included 400 and K-500 alloys. Some of the Monel heat pipes contained copper/nickel wicks that were fabricated by brazing nickel-plated copper felt metal wicks. Although most of the envelope/material combinations exhibit favorable results at 200 °C, some of the combinations failed at higher temperatures. Causes of failure included stress-creep of envelopes and corrosion at axial or end cap welds. This information represents a significant advance in selection of materials for 200 °C to 300 °C water heat pipes. Life testing work is being continued.

  13. Automatic robotic arm operations and sampling in near zero gravity environment - functional tests results from Phobos-Grunt mission

    NASA Astrophysics Data System (ADS)

    Kozlova, Tatiana; Karol Seweryn, D..; Grygorczuk, Jerzy; Kozlov, Oleg

    The sample return missions have made a very significant progress to understanding of geology, the extra-terrestrial materials, processes occurring on surface and subsurface level, as well as of interactions between such materials and mechanisms operating there. The various sample return missions in the past (e.g. Apollo missions, Luna missions, Hayabusa mission) have provided scientists with samples of extra-terrestrial materials allowing to discover answers to critical scientific questions concerning the origin and evolution of the Solar System. Several new missions are currently planned: sample return missions, e.g Russian Luna-28, ESA Phootprint and MarcoPolo-R as well as both robotic and manned exploration missions to the Moon and Mars. One of the key challenges in such missions is the reliable sampling process which can be achieved by using many different techniques, e.g. static excavating technique (scoop), core drilling, sampling using dynamic mechanisms (penetrators), brushes and pneumatic systems. The effectiveness of any sampling strategy depends on many factors, including the required sample size, the mechanical and chemical soil properties (cohesive, hard or porous regolith, stones), the environment conditions (gravity, temperature, pressure, radiation). Many sampling mechanism have been studied, designed and built in the past, two techniques to collect regolith samples were chosen for the Phobos-Grunt mission. The proposed system consisted of a robotic arm with a 1,2m reach beyond the lander (IKI RAN); a tubular sampling device designed for collecting both regolith and small rock fragments (IKI RAN); the CHOMIK device (CBK PAN) - the low velocity penetrator with a single-sample container for collecting samples from the rocky surface. The functional tests were essential step in robotic arm, sampling device and CHOMIK device development process in the frame of Phobos-Grunt mission. Three major results were achieved: (i) operation scenario for autonomous

  14. Application of fuzzy logic-neural network based reinforcement learning to proximity and docking operations: Translational controller results

    NASA Technical Reports Server (NTRS)

    Jani, Yashvant

    1992-01-01

    The reinforcement learning techniques developed at Ames Research Center are being applied to proximity and docking operations using the Shuttle and Solar Maximum Mission (SMM) satellite simulation. In utilizing these fuzzy learning techniques, we also use the Approximate Reasoning based Intelligent Control (ARIC) architecture, and so we use two terms interchangeable to imply the same. This activity is carried out in the Software Technology Laboratory utilizing the Orbital Operations Simulator (OOS). This report is the deliverable D3 in our project activity and provides the test results of the fuzzy learning translational controller. This report is organized in six sections. Based on our experience and analysis with the attitude controller, we have modified the basic configuration of the reinforcement learning algorithm in ARIC as described in section 2. The shuttle translational controller and its implementation in fuzzy learning architecture is described in section 3. Two test cases that we have performed are described in section 4. Our results and conclusions are discussed in section 5, and section 6 provides future plans and summary for the project.

  15. Operational results of the spallation neutron source (SNS) polyphase converter-modulator for the 140 KV klystron RF system

    SciTech Connect

    Reass, W. A.; Doss, James D.; Gribble, R. F.; Lynch, M. T.; Rees, D. E.; Tallerico, P. J.; Borovina, D. L.

    2001-01-01

    This paper describes the first operational results of the 140 kV, 1 MW average, 11 MW peak, zero-voltageswitching, 20 kHz polyphase bridge, boost converter-modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2100 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three 'H-Bridge' Insulated Gate Bipolar Transistor (IGBT) switching networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. Pulse-Width Modulation (PWM) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt peaking is used on the transformer secondary to boost output voltage and resonate transformer leakage inductance. With the appropriate transformer leakage inductance and peaking capacitance, zero-voltage-switching of the IGBT's is attained, minimizing switching losses. Reviews of these design parameters and an examination of the first operational results will be performed.

  16. OPERATIONAL RESULTS OF THE SPALLATION NEUTRON SOURCE (SNS) POLYPHASE CONVERTER-MODULATOR FOR THE 140 KV KLYSTRON RF SYSTEMS

    SciTech Connect

    W.A. REASS; J.D. DOSS; ET AL

    2001-06-01

    This paper describes the first operational results of the 140 kV, 1 MW average, 11 MW peak, zero-voltage-switching, 20 kHz polyphase bridge, boost converter-modulator for klystron pulse application. The DC-DC converter derives the buss voltages from a standard 13.8 kV to 2100 Y substation cast-core transformer. Energy storage and filtering is provided by self-clearing metallized hazy polypropylene traction capacitors. Three ''H-Bridge'' Insulated Gate Bipolar Transistor (IGBT) switching networks are used to generate the polyphase 20 kHz transformer primary drive waveforms. The 20 kHz drive waveforms are chirped the appropriate duration to generate the desired klystron pulse width. Pulse-Width Modulation (PWM) of the individual 20 kHz pulses is utilized to provide regulated output waveforms with adaptive feedforward and feedback techniques. The boost transformer design utilizes amorphous nanocrystalline material that provides the required low core loss at design flux levels and switching frequencies. Resonant shunt peaking is used on the transformer secondary to boost output voltage and resonate transformer leakage inductance. With the appropriate transformer leakage inductance and peaking capacitance, zero-voltage-switching of the IGBT's is attained, minimizing switching losses. Reviews of these design parameters and an examination of the first operational results will be performed.

  17. Results of scoping tests for open-cycle OTEC (Ocean Thermal Energy Conversion) components operating with seawater

    NASA Astrophysics Data System (ADS)

    Zangrando, F.; Bharathan, D.; Green, H. J.; Link, H. F.; Parsons, B. K.; Parsons, J. M.; Pesaran, A. A.; Panchal, C. B.

    1990-09-01

    This report presents comprehensive documentation of the experimental research conducted on open-cycle ocean thermal energy conversion (OC-OTEC) components operating with seawater as a working fluid. The results of this research are presented in the context of previous analysis and fresh-water testing; they provide a basis for understanding and predicting with confidence the performance of all components of an OC-OTEC system except the turbine. Seawater tests have confirmed the results that were obtained in fresh-water tests and predicted by the analytical models of the components. A sound technical basis has been established for the design of larger systems in which net power will be produced for the first time from OC-OTEC technology. Design and operation of a complete OC-OTEC system that produces power will provide sufficient confidence to warrant complete transfer of OC-OTEC technology to the private sector. Each components performance is described in a separate chapter written by the principal investigator responsible for technical aspects of the specific tests. Chapters have been indexed separately for inclusion on the data base.

  18. Results of scoping tests for open-cycle OTEC (ocean thermal energy conversion) components operating with seawater

    SciTech Connect

    Zangrando, F; Bharathan, D; Green, H J; Link, H F; Parsons, B K; Parsons, J M; Pesaran, A A; Panchal, C B

    1990-09-01

    This report presents comprehensive documentation of the experimental research conducted on open-cycle ocean thermal energy conversion (OC-OTEC) components operating with seawater as a working fluid. The results of this research are presented in the context of previous analysis and fresh-water testing; they provide a basis for understanding and predicting with confidence the performance of all components of an OC-OTEC system except the turbine. Seawater tests have confirmed the results that were obtained in fresh-water tests and predicted by the analytical models of the components. A sound technical basis has been established for the design of larger systems in which net power will be produced for the first time from OC-OTEC technology. Design and operation of a complete OC-OTEC system that produces power will provide sufficient confidence to warrant complete transfer of OC-OTEC technology to the private sector. Each components performance is described in a separate chapter written by the principal investigator responsible for technical aspects of the specific tests. Chapters have been indexed separately for inclusion on the data base.

  19. The effect of quality management practices on operational and business results in the petroleum industry in Iran

    NASA Astrophysics Data System (ADS)

    Mellat Parast, Mahour

    The trend toward globalization has challenged management thinking, organizational practices, and the ways companies interact with their customers and suppliers as well as with other segments of society. One such practice, Total Quality Management (TQM), has emerged as a management paradigm for enhancing organizational performance and profitability, to the extent that it has been regarded as "the second industrial revolution" (Kanji, 1990). Despite extensive research in quality management, little empirical research has been done on this in an international context, especially in the Middle East. This study attempts to investigate: (1) the relationship among quality management constructs based on the Malcolm Baldrige National Quality Award; and (2) the effect of quality management practices on operational and business results in the petroleum industry. A validated and reliable survey instrument was used for the study to collect data from 31 project managers/consultants in the petroleum industry in Iran. The results of the correlation analysis show that top management support is the major driver of quality management, which significantly correlates with other quality management practices. It was also found that customer orientation is not significantly correlated with external quality results (profitability). A regression analysis indicated top management support, employee training, and employee involvement as the three statistically significant variables in explaining the variability in internal quality results. Furthermore, it was found that internal quality results was statistically significant in explaining the variability of external quality results.

  20. Impacts of Large Amounts of Wind Power on Design and Operation of Power Systems; Results of IEA Collaboration

    SciTech Connect

    Parsons, B.; Ela, E.; Holttinen, H.; Meibom, P.; Orths, A.; O'Malley, M.; Ummels, B. C.; Tande, J.; Estanqueiro, A.; Gomez, E.; Smith, J. C.

    2008-06-01

    There are a multitude of studies completed and ongoing related to the cost of wind integration. However, the results are not easy to compare. An international forum for exchange of knowledge of power system impacts of wind power has been formed under the IEA Implementing Agreement on Wind Energy. IEA WIND R&D Task 25 on “Design and Operation of Power Systems with Large Amounts of Wind Power” produced a state-of-the-art report in October 2007, where the most relevant wind-power grid integration studies were analyzed, especially regarding methodologies and input data. This paper summarizes the results from 18 case studies, with discussion on differences in methodology as well as issues that have been identified to impact the cost of wind integration.

  1. Fuel Property, Emission Test, and Operability Results from a Fleet of Class 6 Vehicles Operating on Gas-to-Liquid Fuel and Catalyzed Diesel Particle Filters

    SciTech Connect

    Alleman, T. L.; Eudy, L.; Miyasato, M.; Oshinuga, A.; Allison, S.; Corcoran, T.; Chatterjee, S.; Jacobs, T.; Cherrillo, R. A.; Clark, R.; Virrels, I.; Nine, R.; Wayne, S.; Lansing, R.

    2005-11-01

    A fleet of six 2001 International Class 6 trucks operating in southern California was selected for an operability and emissions study using gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (CDPF). Three vehicles were fueled with CARB specification diesel fuel and no emission control devices (current technology), and three vehicles were fueled with GTL fuel and retrofit with Johnson Matthey's CCRT diesel particulate filter. No engine modifications were made.

  2. Does the number of veins ligated during varicococele surgery influence post-operative semen and hormone results?

    PubMed

    Majzoub, A; Elbardisi, H; Arafa, M; Agarwal, A; Al Said, S; Al Rumaihi, K

    2016-09-01

    Varicocele is a well-established cause of male subfertility, which is directly proportional to its clinical grade. Although newer ultrasonic grading systems have taken into account the existence of pampiniform venous plexi, little is known about the clinical significance of the number of veins ligated during surgery. Very few undersized studies reported an influence which triggered the need to evaluate such association. This is a retrospective study of 378 patients who underwent left microsurgical subinguinal varicocoelectomy. Semen analyses and blood hormone studies performed pre-operatively were compared to those executed 6 months after surgery. Patients were divided into abnormal semen and normal semen groups based on their initial semen results. They were also subdivided according to the number of veins ligated intraoperatively into three groups: <5, 5-10, and >10 veins. Sperm count, total motility, and progressive motility were significantly increased in 62, 60.3, and 53.3% of patients post-operatively (p = 0.001), respectively. No significant differences in hormone levels were detected overall. Of the 378 patients, 332 had an abnormal semen analysis, while the remaining 46 patients had a normal result. Sperm count, total motility, and progressive motility significantly increased after varicocoelectomy in patients with an abnormal initial semen analysis (p = 0.001). In 48.7% of patients, 5-10 veins were ligated during surgery, whereas 28.3% had >10 and 23% had <5 ligated veins. No statistically significant differences were noted in the initial or the follow-up results among the number of vein subgroups. Varicocele ligation improves patients' fertility potential. This improvement, however, is not influenced by the number of veins ligated intraoperatively. Clinical grading maintains its superiority in the evaluation of varicocele patients. PMID:27317389

  3. Liver resection for colorectal liver metastases with peri-operative chemotherapy: oncological results of R1 resections

    PubMed Central

    Eveno, Clarisse; Karoui, Mehdi; Gayat, Etienne; Luciani, Alain; Auriault, Marie-Luce; Kluger, Michael D; Baumgaertner, Isabelle; Baranes, Laurence; Laurent, Alexis; Tayar, Claude; Azoulay, Daniel; Cherqui, Daniel

    2013-01-01

    Background Retrospective analysis of outcomes of R0 (negative margin) versus R1 (positive margin) liver resections for colorectal metastases (CLM) in the context of peri-operative chemotherapy. Methods All CLM resections between 2000 and 2006 were reviewed. Exclusion criteria included: macroscopically incomplete (R2) resections, the use of local treatment modalities, the presence of extra-hepatic disease and no peri-operative chemotherapy. R0/R1 status was based on pathological examination. Results Of 86 eligible patients, 63 (73%) had R0 and 23 (27%) had R1 resections. The two groups were comparable for the number, size of metastases and type of hepatectomy. The R1 group had more bilobar CLM (52% versus 24%, P = 0.018). The median follow-up was 3.1 years. Five-year overall and disease-free survival were 54% and 21% for the R0 group and 49% and 22% for the R1 group (P = 0.55 and P = 0.39, respectively). An intra-hepatic recurrence was more frequent in the R1 group (52% versus 27%, P = 0.02) and occurred more frequently at the surgical margin (22% versus 3%, P = 0.01). Discussion R1 resections were associated with a higher risk of intra-hepatic and surgical margin recurrence but did not negatively impact survival suggesting that in the era of efficient chemotherapy, the risk of an R1 resection should not be considered as a contraindication to surgery. PMID:23458567

  4. Comparison of simulated and actual wind shear radar data products

    NASA Technical Reports Server (NTRS)

    Britt, Charles L.; Crittenden, Lucille H.

    1992-01-01

    Prior to the development of the NASA experimental wind shear radar system, extensive computer simulations were conducted to determine the performance of the radar in combined weather and ground clutter environments. The simulation of the radar used analytical microburst models to determine weather returns and synthetic aperture radar (SAR) maps to determine ground clutter returns. These simulations were used to guide the development of hazard detection algorithms and to predict their performance. The structure of the radar simulation is reviewed. Actual flight data results from the Orlando and Denver tests are compared with simulated results. Areas of agreement and disagreement of actual and simulated results are shown.

  5. The operation results with the modified charging equipment and ignition furnace at Kwangyang No. 2 sinter plant

    SciTech Connect

    Lee, K.J.; Pi, Y.J.; Kim, J.R.; Lee, J.N.

    1996-12-31

    There will be another blast furnace, the production capacity of which is 3.0 million tonnes per year in 1999 and mini mill plant, the production capacity of which is 1.8 million tonnes per year in 1996 at Kwangyang Works. Therefore, the coke oven gas and burnt lime will be deficient and more sinter will be needed. To meet with these situations, the authors modified the charging equipment and ignition furnace at Kwangyang No. 2 sinter plant in April 1995. After the modification of the charging equipment and ignition furnace, the consumption of burnt lime and coke oven gas could be decreased and the sinter productivity increased in spite of the reduction of burnt lime consumption. This report describes the operation results with the modification of the charging equipment and ignition furnace in No. 2 sinter plant Kwangyang works.

  6. Results from the second year of operation of the Federal Methanol Fleet at Oak Ridge National Laboratory

    SciTech Connect

    West, B.H.; McGill ); Hillis, S.L. )

    1990-09-01

    The Oak Ridge National Laboratory has completed its second year of operation of ten vehicles for the Federal Methanol Fleet Project; five of the vehicles are fueled with methanol. Over 56,000 miles were accumulated on the vehicles in the second year bringing the total to over 152,000 miles. Energy consumption for the methanol cars was slightly higher than that of the gasoline cars again this year, most likely as a result of shorter average trip lengths for the methanol gas. Iron and lead have accumulated at greater rates in the lubricating oil of the methanol cars. Driver's ratings of vehicles reflected some dissatisfaction with the cold-weather performance of the methanol cars, but the cars have no special provisions for cold weather starting, and the fuel vapor pressure has not been tailored to the season as at other test sites. Otherwise, drivers' opinions of the methanol cars have been favorable. 13 refs., 4 figs., 10 tabs.

  7. Research on an expert system for database operation of simulation-emulation math models. Volume 1, Phase 1: Results

    NASA Technical Reports Server (NTRS)

    Kawamura, K.; Beale, G. O.; Schaffer, J. D.; Hsieh, B. J.; Padalkar, S.; Rodriguez-Moscoso, J. J.

    1985-01-01

    The results of the first phase of Research on an Expert System for Database Operation of Simulation/Emulation Math Models, is described. Techniques from artificial intelligence (AI) were to bear on task domains of interest to NASA Marshall Space Flight Center. One such domain is simulation of spacecraft attitude control systems. Two related software systems were developed to and delivered to NASA. One was a generic simulation model for spacecraft attitude control, written in FORTRAN. The second was an expert system which understands the usage of a class of spacecraft attitude control simulation software and can assist the user in running the software. This NASA Expert Simulation System (NESS), written in LISP, contains general knowledge about digital simulation, specific knowledge about the simulation software, and self knowledge.

  8. A framework for the assessment and analysis of multi-hazards induced risk resulting from space vehicles operations

    NASA Astrophysics Data System (ADS)

    Sala-Diakanda, Serge N.

    2007-12-01

    With the foreseeable increase in traffic frequency to and from orbit, the safe operation of current and future space vehicles at designated spaceports has become a serious concern. Due to their high explosive energy potential, operating those launch vehicles presents a real risk to: (1) the spaceport infrastructure and personnel, (2) the communities surrounding the spaceport and (3) the flying aircrafts whose routes could be relatively close to spaceport launch and reentry routes. Several computer models aimed at modeling the effects of the different hazards generated by the breakup of such vehicles (e.g., fragmentation of debris, release of toxic gases, propagation of blast waves, etc.) have been developed, and are used to assist in Go-No Go launch decisions. They can simulate a total failure scenario of the vehicle and, estimate a number of casualties to be expected as a result of such failure. However, as all of these models---which can be very elaborate and complex---consider only one specific explosion hazard in their simulations, the decision of whether or not a launch should occur is currently based on the evaluation of several estimates of an expected number of casualties. As such, current practices ignore the complex, nonlinear interactions between the different hazards as well as the interdependencies between the estimates. In this study, we developed a new framework which makes use of information fusion theory, hazards' dispersion modeling and, geographical statistical analysis and visualization capabilities of geographical information systems to assess the risk generated by the operation of space launch vehicles. A new risk metric, which effectively addresses the lack of a common risk metric with current methods, is also proposed. A case study, based on a proposed spaceport in the state of Oklahoma showed that the estimates we generate through our framework consistently outperform estimates provided by any individual hazard, or by the independent

  9. In-orbit test result of an operational optical intersatellite link between ARTEMIS and SPOT4, SILEX

    NASA Astrophysics Data System (ADS)

    Tolker-Nielsen, Toni; Oppenhauser, Gotthard

    2002-04-01

    The Semi conductor Inter satellite Link EXperiment, SILEX, consists of two terminals, one terminal embarked on the French LEO observation satellite SPOT4 and one terminal embarked on ESA's GEO telecommunication satellite ARTEMIS. The objective of SILEX is to perform optical communication experiments in orbit and on an operational basis transmit SPOT4 Earth observation data to ARTEMIS, which will relay the data to ground via its Ka band feeder link. SPOT4 was successfully launched on 22nd March 1998. The ARTEMIS launch on 12th July 2001 left ARTEMIS in an orbit with too low apogee, necessitating orbit raising to a circular parking orbit, altitude 31000 km, using a large fraction of the chemical propellant on board. The remaining 5000 km to GEO stationary orbit will be achieved using the low thrust innovative electric propulsion system necessitating specific attitude control software. The final orbit raising will last about 6 months and the expected lifetime of ARTEMIS after station acquisition is 5 years. While waiting for the establishment of the new attitude control software and the beginning of the final orbit raising maneuvers a test program has been undertaken to characterize the performances of the SILEX system. Testing was performed every fifth day when ARTEMIS was visible over Europe. The test program involves Optical Ground Station acquisition and tracking, inter-satellite link acquisition and tracking, bit error rate measurements and transmission of Earth observation data. The paper reports on results of the in orbit testing, giving comparisons with predictions. The conclusion of the test program is that the SILEX system has excellent performances qualifying the system for operational use by SPOTIMAGE in parallel with a detailed technological experimentation program involving the two SILEX terminals, ESA's optical ground station on Tenerife, and also NASDA's OICETS, once ARTEMIS has acquired its final orbital position.

  10. PRA in Design: Increasing Confidence in Pre-Operational Assessments of Risks (Results of a Joint NASA/NRC Workshop)

    NASA Technical Reports Server (NTRS)

    Youngblood, Robert; Dezfuli, Homayoon; Siu, Nathan

    2010-01-01

    In late 2009, the National Aeronautics and Space Administration (NASA) and the U.S. Nuclear Regulatory Commission (NRC) jointly organized a workshop to discuss technical issues associated with application of risk assessments to early phases of system design. The workshop, which was coordinated by the Idaho National Laboratory, involved invited presentations from a number of PRA experts in the aerospace and nuclear fields and subsequent discussion to address the following questions: (a) What technical issues limit decision-makers' confidence in PRA results, especially at a pre-operational phase of the system life cycle? (b) What is being done to address these issues'? (c) What more can be done ? The workshop resulted in participant observations and suggestions on several technical issues, including the pursuit of non-traditional approaches to risk assessment and the verification and validation of risk models. The workshop participants also identified several important non-technical issues, including risk communication with decision makers, and the integration of PRA into the overall design process.

  11. Laparoscopic sleeve gastrectomy for morbid obesity with intra-operative endoscopic guidance. Immediate peri-operative and 1-year results after 25 patients.

    PubMed

    Diamantis, T; Alexandrou, A; Pikoulis, E; Diamantis, D; Griniatsos, J; Felekouras, E; Papalambros, E

    2010-08-01

    Laparoscopic sleeve gastrectomy (LSG) represents a promising alternative option for the surgical treatment of morbid obesity. Its standard technique includes the longitudinal division of the stomach along a bougie of varying diameter. We report in this retrospective study our experience with LSG being performed with the use of intra-operative endoscopy instead of the bougie. Twenty-five consecutive patients (18 women, seven men) with a mean age of 40.2 years and mean body weight of 152.1 kg were submitted to LSG with intra-operative endoscopy in our hospital. The mean preoperative BMI was 53.5 kg/m(2). There were no conversions. Mean operative time was 117.5 min. There was no morbidity or mortality. The mean loss of excess body weight (EBW) at 3 months post-op was 19 +/- 1.8 kg, at 6 months was 28.6 +/- 4.5 kg, and at 1 year post-op was 48.9 +/- 3.7 kg (min 11-max 92). In other words the patients had lost 30 +/- 5%, 45 +/- 7.7%, and 60.8 +/- 4.3% of their EBW, respectively. The mean excess body weight loss at the day of the last visit to our outpatient clinic was 52.3 +/- 4.3 kg which corresponded to 66.4 +/- 4.3% of the total excess weight. LSG with intra-operative endoscopic guidance is a safe and efficient alternative method to treat morbid obesity and is a viable option for surgical units familiar with endoscopic techniques. PMID:20464526

  12. Experimental philosophy of actual and counterfactual free will intuitions.

    PubMed

    Feltz, Adam

    2015-11-01

    Five experiments suggested that everyday free will and moral responsibility judgments about some hypothetical thought examples differed from free will and moral responsibility judgments about the actual world. Experiment 1 (N=106) showed that free will intuitions about the actual world measured by the FAD-Plus poorly predicted free will intuitions about a hypothetical person performing a determined action (r=.13). Experiments 2-5 replicated this result and found the relations between actual free will judgments and free will judgments about hypothetical determined or fated actions (rs=.22-.35) were much smaller than the differences between them (ηp(2)=.2-.55). These results put some pressure on theoretical accounts of everyday intuitions about freedom and moral responsibility. PMID:26126174

  13. Results of toxicity tests and chemical analyses conducted on sediments collected from the TNX Outfall Delta Operable Unit, July 1999

    SciTech Connect

    Specht, W.L.

    2000-02-11

    In order to provide unit specific toxicity data that will be used to address critical uncertainty in the ecological risk assessment (ERA) for the TNX Outfall Delta Operable Unit (TNXOD OU), sediments were collected from eight locations in the Inner Swamp portion of the operable unit and two unit specific background locations. These samples were analyzed for total mercury, total uranium, and sediment toxicity.

  14. Functional brain imaging using near-infrared spectroscopy during actual driving on an expressway

    PubMed Central

    Yoshino, Kayoko; Oka, Noriyuki; Yamamoto, Kouji; Takahashi, Hideki; Kato, Toshinori

    2013-01-01

    The prefrontal cortex is considered to have a significant effect on driving behavior, but little is known about prefrontal cortex function in actual road driving. Driving simulation experiments are not the same, because the subject is in a stationary state, and the results may be different. Functional near-infrared spectroscopy (fNIRS) is advantageous in that it can measure cerebral hemodynamic responses in a person driving an actual vehicle. We mounted fNIRS equipment in a vehicle to evaluate brain functions related to various actual driving operations while the subjects drove on a section of an expressway that was not yet open to the public. Measurements were recorded while parked, and during acceleration, constant velocity driving (CVD), deceleration, and U-turns, in the daytime and at night. Changes in cerebral oxygen exchange (ΔCOE) and cerebral blood volume were calculated and imaged for each part of the task. Responses from the prefrontal cortex and the parietal cortex were highly reproducible in the daytime and nighttime experiments. Significant increases in ΔCOE were observed in the frontal eye field (FEF), which has not been mentioned much in previous simulation experiments. In particular, significant activation was detected during acceleration in the right FEF, and during deceleration in the left FEF. Weaker responses during CVD suggest that FEF function was increased during changes in vehicle speed. As the FEF contributes to control of eye movement in three-dimensional space, FEF activation may be important in actual road driving. fNIRS is a powerful technique for investigating brain activation outdoors, and it proved to be sufficiently robust for use in an actual highway driving experiment in the field of intelligent transport systems (ITS). PMID:24399949

  15. Improved operating scenarios of the DIII-D tokamak as a result of the addition of UNIX computer systems

    SciTech Connect

    Henline, P.A.

    1995-10-01

    The increased use of UNIX based computer systems for machine control, data handling and analysis has greatly enhanced the operating scenarios and operating efficiency of the DRI-D tokamak. This paper will describe some of these UNIX systems and their specific uses. These include the plasma control system, the electron cyclotron heating control system, the analysis of electron temperature and density measurements and the general data acquisition system (which is collecting over 130 Mbytes of data). The speed and total capability of these systems has dramatically affected the ability to operate DIII-D. The improved operating scenarios include better plasma shape control due to the more thorough MHD calculations done between shots and the new ability to see the time dependence of profile data as it relates across different spatial locations in the tokamak. Other analysis which engenders improved operating abilities will be described.

  16. Column densities resulting from shuttle sublimator/evaporator operation. [optical density of nozzle flow containing water vapor

    NASA Technical Reports Server (NTRS)

    Naumann, R. J.

    1973-01-01

    The proposed disposal of H2O from the shuttle fuel cell operation by ejecting it in vapor form through a supersonic nozzle at the rate of 100 lb/day has been investigated from the point of view of the possible interference to astronomical experiments. If the nozzle is located at the tail and directed along the shuttle longitudinal axis, the resulting column density will be less than 10 to th 12th power molecules/sq cm at viewing angles larger than 48 deg above the longitudinal axis. The molecules in the trail will diffuse rapidly. The column density contribution from molecules expelled on the previous orbit is 1.3 x 10 to the 8th power molecules/sq cm. This contribution diminishes by the inverse square root of the number of orbits since the molecules were expelled. The molecular backscatter from atmospheric molecules is also calculated. If the plume is directed into the flight path, the column density along a perpendicular is found to be 1.5 x 10 to the 11th power molecules/sq cm. The return flux is estimated to be of the order of 10 to the 12th power molecules/sq cm/sec at the stagnation point. With reasonable care in design of experiments to protect them from the backscatter flux of water molecules, the expulsion of 100 lb/day does not appear to create an insurmountable difficulty for the shuttle experiments.

  17. Offsite radiation doses from Hanford Operations for the years 1983 through 1987: A comparison of results calculated by two methods

    SciTech Connect

    Soldat, J.K.

    1989-10-01

    This report compares the results of the calculation of potential radiation doses to the public by two different environmental dosimetric systems for the years 1983 through 1987. Both systems project the environmental movement of radionuclides released with effluents from Hanford operations; their concentrations in air, water, and foods; the intake of radionuclides by ingestion and inhalation; and, finally, the potential radiation doses from radionuclides deposited in the body and from external sources. The first system, in use for the past decade at Hanford, calculates radiation doses in terms of 50-year cumulative dose equivalents to body organs and to the whole body, based on the methodology defined in ICRP Publication 2. This system uses a suite of three computer codes: PABLM, DACRIN, and KRONIC. In the new system, 50-year committed doses are calculated in accordance with the recommendations of the ICRP Publications 26 and 30, which were adopted by the US Department of Energy (DOE) in 1985. This new system calculates dose equivalent (DE) to individual organs and effective dose equivalent (EDE). The EDE is a risk-weighted DE that is designed to be an indicator of the potential health effects arising from the radiation dose. 16 refs., 1 fig., 38 tabs.

  18. RF Design and Operating Results for a New 201.25 MHz RF Power Amplifier for LANSCE

    SciTech Connect

    Lyles, John T.; Baca, David M.; Bratton, Ray E.; Brennan, Nicholas W.; Bultman, Nathan K.; Chen, Zukun; Davis, Jerry L.; Naranjo, Angela C.; Rees, Daniel E.; Sandoval, Gilbert M. Jr.; Summers, Richard D.

    2011-01-01

    A prototype VHF RF Final Power Amplifier (FPA) for Los Alamos Neutron Science Center (LANSCE) has been designed, fabricated, and tested. The cavity amplifier has met the goals of generating 2.5 MW peak and 260 kW of average power, at an elevation of 2.1 km. It was designed to use a Thales TH628 Diacrode{sup R}, a state-of-art tetrode power tube that is double-ended, providing roughly twice the power of a conventional tetrode. The amplifier is designed with tunable input and output transmission line cavity circuits, a grid decoupling circuit, an adjustable output coupler, TE mode suppressors, blocking, bypassing and decoupling capacitors, and a cooling system. The tube is connected in a full wavelength output circuit, with the lower main tuner situated 3/4{lambda} from the central electron beam region in the tube and the upper slave tuner 1/4{lambda} from the same point. We summarize the design processes and features of the FPA along with significant test results. A pair of production amplifiers are planned to be power-combined and installed at the LANSCE DTL to return operation to full beam duty factor.

  19. Near-term Horizontal Launch for Flexible Operations: Results of the DARPA/NASA Horizontal Launch Study

    NASA Technical Reports Server (NTRS)

    Bartolotta, Paul A.; Wilhite, Alan W.; Schaffer, Mark G.; Huebner, Lawrence D.; Voland, Randall T.; Voracek, David F.

    2012-01-01

    Horizontal launch has been investigated for 60 years by over 130 different studies. During this time only one concept, Pegasus, has ever been in operation. The attractiveness of horizontal launch is the capability to provide a "mobile launch pad" that can use existing aircraft runways, cruise above weather, loiter for mission instructions, and provide precise placement for orbital intercept, rendezvous, or reconnaissance. A jointly sponsored study by DARPA and NASA, completed in 2011, explored the trade space of horizontal launch system concepts which included an exhaustive literature review of the past 70 years. The Horizontal Launch Study identified potential near- and mid-term concepts capable of delivering 15,000 lb payloads to a 28.5 due East inclination, 100 nautical-mile low-Earth orbit. Results are presented for a range of near-term system concepts selected for their availability and relatively low design, development, test, and evaluation (DDT&E) costs. This study identified a viable low-cost development path forward to make a robust and resilient horizontal launch capability a reality.

  20. Actual preoperative fasting time in Brazilian hospitals: the BIGFAST multicenter study

    PubMed Central

    de Aguilar-Nascimento, José E; de Almeida Dias, Ana L; Dock-Nascimento, Diana B; Correia, Maria Isabel TD; Campos, Antonio CL; Portari-Filho, Pedro Eder; Oliveira, Sergio S

    2014-01-01

    Background Prolonged fasting increases organic response to trauma. This multicenter study investigated the gap between the prescribed and the actual preoperative fasting times in Brazilian hospitals and factors associated with this gap. Methods Patients (18–90-years-old) who underwent elective operations between August 2011 and September 2012 were included in the study. The actual and prescribed times for fasting were collected and correlated with sex, age, surgical disease (malignancies or benign disease), operation type, American Society of Anesthesiologists score, type of hospital (public or private), and nutritional status. Results A total of 3,715 patients (58.1% females) with a median age of 49 (18–94) years from 16 Brazilian hospitals entered the study. The median (range) preoperative fasting time was 12 (2–216) hours, and fasting time was longer (P<0.001) in hospitals using a traditional fasting protocol (13 [6–216] hours) than in others that had adopted new guidelines (8 [2–48] hours). Almost 80% (n=2,962) of the patients were operated on after 8 or more hours of fasting and 46.2% (n=1,718) after more than 12 hours. Prolonged fasting was not associated with physical score, age, sex, type of surgery, or type of hospital. Patients operated on due to a benign disease had an extended duration of preoperative fasting. Conclusion Actual preoperative fasting time is significantly longer than prescribed fasting time in Brazilian hospitals. Most of these hospitals still adopt traditional rather than modern fasting guidelines. All patients are at risk of long periods of fasting, especially those in hospitals that follow traditional practices. PMID:24627636

  1. Motor-operated gearbox efficiency

    SciTech Connect

    DeWall, K.G.; Watkins, J.C.; Bramwell, D.; Weidenhamer, G.H.

    1996-12-01

    Researchers at the Idaho National Engineering Laboratory recently conducted tests investigating the operating efficiency of the power train (gearbox) in motor-operators typically used in nuclear power plants to power motor-operated valves. Actual efficiency ratios were determined from in-line measurements of electric motor torque (input to the operator gearbox) and valve stem torque (output from the gearbox) while the operators were subjected to gradually increasing loads until the electric motor stalled. The testing included parametric studies under reduced voltage and elevated temperature conditions. As part of the analysis of the results, the authors compared efficiency values determined from testing to the values published by the operator manufacturer and typically used by the industry in calculations for estimating motor-operator capabilities. The operators they tested under load ran at efficiencies lower than the running efficiency (typically 50%) published by the operator manufacturer.

  2. Motor-operator gearbox efficiency

    SciTech Connect

    DeWall, K.G.; Watkins, J.C.; Bramwell, D.

    1996-06-01

    Researchers at the Idaho National Engineering Laboratory recently conducted tests investigating the operating efficiency of the power train (gearbox) in motor-operators typically used in nuclear power plants to power motor-operated valves. Actual efficiency ratios were determined from in-line measurements of electric motor torque (input to the operator gearbox) and valve stem torque (output from the gearbox) while the operators were subjected to gradually increasing loads until the electric motor stalled. The testing included parametric studies under reduced voltage and elevated temperature conditions. As part of the analysis of the results, we compared efficiency values determined from testing to the values published by the operator manufacturer and typically used by the industry in calculations for estimating motor-operator capabilities. The operators we tested under load ran at efficiencies lower than the running efficiency (typically 50%) published by the operator manufacturer.

  3. Investigating the discrepancy between the predicted and actual energy performance of buildings

    NASA Astrophysics Data System (ADS)

    Demanuele, Christine

    The threat of climate change has increased the demand for energy efficiency in buildings, with various stakeholders requesting more accurate predictions of energy consumption, and energy consultants coming under increased pressure to guarantee the energy performance of buildings. This study aims to investigate the factors causing the discrepancy which currently exists between the predicted and actual energy performance of buildings, which will lead to a deeper understanding of this discrepancy and, ultimately, more accurate energy predictions. As part of this study, a non-domestic building in London was modelled and monitored, so as to identify the main contributors to the discrepancy between the predicted and actual energy consumption. In addition, sensitivity analysis was carried out on a number of input variables to establish the set of influential parameters, and to determine whether using such techniques would successfully predict the range in which building energy consumption is likely to fall. The results show that the uncertainty calculated from differential sensitivity analysis encompasses the actual energy performance of the building. The most variable and influential parameters are those which are controlled by occupants, therefore it is paramount that management and occupants are well-informed about the building operation for energy targets to be achieved. Although the sensitivity analysis methods employed are impractical for commercial use, it is possible to develop simpler methods, encompassing all stages of building design and operation, which would decrease the discrepancy between the actual and predicted energy performance of buildings. Such techniques would be invaluable to energy consultants, for whom the cost resting on uncertainties in predictions is substantial due to more demanding clients and fines liable to be paid if energy predictions go wrong. A better understanding of the discrepancy, together with more accurate predictions, would

  4. What Does the Force Concept Inventory Actually Measure?

    ERIC Educational Resources Information Center

    Huffman, Douglas; Heller, Patricia

    1995-01-01

    The Force Concept Inventory (FCI) is a 29-question, multiple-choice test designed to assess students' Newtonian and non-Newtonian conceptions of force. Presents an analysis of FCI results as one way to determine what the inventory actually measures. (LZ)

  5. 50 CFR 253.16 - Actual cost.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 50 Wildlife and Fisheries 9 2011-10-01 2011-10-01 false Actual cost. 253.16 Section 253.16 Wildlife and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE AID TO FISHERIES FISHERIES ASSISTANCE PROGRAMS Fisheries Finance Program §...

  6. 50 CFR 253.16 - Actual cost.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 50 Wildlife and Fisheries 11 2013-10-01 2013-10-01 false Actual cost. 253.16 Section 253.16 Wildlife and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE AID TO FISHERIES FISHERIES ASSISTANCE PROGRAMS Fisheries Finance Program §...

  7. Humanistic Education and Self-Actualization Theory.

    ERIC Educational Resources Information Center

    Farmer, Rod

    1984-01-01

    Stresses the need for theoretical justification for the development of humanistic education programs in today's schools. Explores Abraham Maslow's hierarchy of needs and theory of self-actualization. Argues that Maslow's theory may be the best available for educators concerned with educating the whole child. (JHZ)

  8. Children's Rights and Self-Actualization Theory.

    ERIC Educational Resources Information Center

    Farmer, Rod

    1982-01-01

    Educators need to seriously reflect upon the concept of children's rights. Though the idea of children's rights has been debated numerous times, the idea remains vague and shapeless; however, Maslow's theory of self-actualization can provide the children's rights idea with a needed theoretical framework. (Author)

  9. Culture Studies and Self-Actualization Theory.

    ERIC Educational Resources Information Center

    Farmer, Rod

    1983-01-01

    True citizenship education is impossible unless students develop the habit of intelligently evaluating cultures. Abraham Maslow's theory of self-actualization, a theory of innate human needs and of human motivation, is a nonethnocentric tool which can be used by teachers and students to help them understand other cultures. (SR)

  10. Group Counseling for Self-Actualization.

    ERIC Educational Resources Information Center

    Streich, William H.; Keeler, Douglas J.

    Self-concept, creativity, growth orientation, an integrated value system, and receptiveness to new experiences are considered to be crucial variables to the self-actualization process. A regular, year-long group counseling program was conducted with 85 randomly selected gifted secondary students in the Farmington, Connecticut Public Schools. A…

  11. Racial Discrimination in Occupations: Perceived and Actual.

    ERIC Educational Resources Information Center

    Turner, Castellano B.; Turner, Barbara F.

    The relationship between the actual representation of Blacks in certain occupations and individual perceptions of the occupational opportunity structure were examined. A scale which rated the degree of perceived discrimination against Blacks in 21 occupations was administered to 75 black male, 70 black female, 1,429 white male and 1,457 white…

  12. Developing Human Resources through Actualizing Human Potential

    ERIC Educational Resources Information Center

    Clarken, Rodney H.

    2012-01-01

    The key to human resource development is in actualizing individual and collective thinking, feeling and choosing potentials related to our minds, hearts and wills respectively. These capacities and faculties must be balanced and regulated according to the standards of truth, love and justice for individual, community and institutional development,…

  13. Potential use of pyrite cinders as raw material in cement production: results of industrial scale trial operations.

    PubMed

    Alp, I; Deveci, H; Yazici, E Y; Türk, T; Süngün, Y H

    2009-07-15

    Pyrite cinders, which are the waste products of sulphuric acid manufacturing plants, contain hazardous heavy metals with potential environmental risks for disposal. In this study, the potential use of pyrite cinders (PyCs) as iron source in the production of Portland cement clinker was demonstrated at the industrial scale. The chemical and mineralogical analyses of the PyC sample used in this study have revealed that it is essentially a suitable raw material for use as iron source since it contains >87% Fe(2)O(3) mainly in the form of hematite (Fe(2)O(3)) and magnetite (Fe(3)O(4)). The samples of the clinkers produced from PyC in the industrial scale trial operation of 6 months were tested for the conformity of their chemical composition and the physico-mechanical performance of the resultant cement products. The data were compared with the clinker products of the iron ore, which is used as the raw material for the production Portland cement clinker in the plant. The chemical compositions of all the clinker products of PyC appeared to conform to those of the iron ore clinker, and hence, a Portland cement clinker. The mechanical performance of the mortars prepared from the PyC clinker was found to be consistent with those of the industrial cements e.g. CEM I type cements. It can be inferred from the leachability tests (TCLP and SPLP) that PyC could be a potential source of heavy metal pollution while the mortar samples obtained from the PyC clinkers present no environmental problems. These findings suggest that the waste pyrite cinders can be readily used as iron source for the production of Portland cement. The availability of PyC in large quantities at low cost provides further significant benefits for the management/environmental practices of these wastes and for the reduction of mining and processing costs of cement raw materials. PMID:19100685

  14. A rail system for circular synthetic aperture sonar imaging and acoustic target strength measurements: Design/operation/preliminary results

    NASA Astrophysics Data System (ADS)

    Kennedy, J. L.; Marston, T. M.; Lee, K.; Lopes, J. L.; Lim, R.

    2014-01-01

    A 22 m diameter circular rail, outfitted with a mobile sonar tower trolley, was designed, fabricated, instrumented with underwater acoustic transducers, and assembled on a 1.5 m thick sand layer at the bottom of a large freshwater pool to carry out sonar design and target scattering response studies. The mobile sonar tower translates along the rail via a drive motor controlled by customized LabVIEW software. The rail system is modular and assembly consists of separately deploying eight circular arc sections, measuring a nominal center radius of 11 m and 8.64 m arc length each, and having divers connect them together in the underwater environment. The system enables full scale measurements on targets of interest with 0.1° angular resolution over a complete 360° aperture, without disrupting target setup, and affording a level of control over target environment conditions and noise sources unachievable in standard field measurements. In recent use, the mobile cart carrying an instrumented sonar tower was translated along the rail in 720 equal position increments and acoustic backscatter data were acquired at each position. In addition, this system can accommodate both broadband monostatic and bistatic scattering measurements on targets of interest, allowing capture of target signature phenomena under diverse configurations to address current scientific and technical issues encountered in mine countermeasure and unexploded ordnance applications. In the work discussed here, the circular rail apparatus is used for acoustic backscatter testing, but this system also has the capacity to facilitate the acquisition of magnetic and optical sensor data from targets of interest. A brief description of the system design and operation will be presented along with preliminary processed results for data acquired from acoustic measurements conducted at the Naval Surface Warfare Center, Panama City Division Test Pond Facility. [Work Supported by the U.S. Office of Naval Research and

  15. A rail system for circular synthetic aperture sonar imaging and acoustic target strength measurements: design/operation/preliminary results.

    PubMed

    Kennedy, J L; Marston, T M; Lee, K; Lopes, J L; Lim, R

    2014-01-01

    A 22 m diameter circular rail, outfitted with a mobile sonar tower trolley, was designed, fabricated, instrumented with underwater acoustic transducers, and assembled on a 1.5 m thick sand layer at the bottom of a large freshwater pool to carry out sonar design and target scattering response studies. The mobile sonar tower translates along the rail via a drive motor controlled by customized LabVIEW software. The rail system is modular and assembly consists of separately deploying eight circular arc sections, measuring a nominal center radius of 11 m and 8.64 m arc length each, and having divers connect them together in the underwater environment. The system enables full scale measurements on targets of interest with 0.1° angular resolution over a complete 360° aperture, without disrupting target setup, and affording a level of control over target environment conditions and noise sources unachievable in standard field measurements. In recent use, the mobile cart carrying an instrumented sonar tower was translated along the rail in 720 equal position increments and acoustic backscatter data were acquired at each position. In addition, this system can accommodate both broadband monostatic and bistatic scattering measurements on targets of interest, allowing capture of target signature phenomena under diverse configurations to address current scientific and technical issues encountered in mine countermeasure and unexploded ordnance applications. In the work discussed here, the circular rail apparatus is used for acoustic backscatter testing, but this system also has the capacity to facilitate the acquisition of magnetic and optical sensor data from targets of interest. A brief description of the system design and operation will be presented along with preliminary processed results for data acquired from acoustic measurements conducted at the Naval Surface Warfare Center, Panama City Division Test Pond Facility. [Work Supported by the U.S. Office of Naval Research and

  16. Whiteheadian Actual Entitities and String Theory

    NASA Astrophysics Data System (ADS)

    Bracken, Joseph A.

    2012-06-01

    In the philosophy of Alfred North Whitehead, the ultimate units of reality are actual entities, momentary self-constituting subjects of experience which are too small to be sensibly perceived. Their combination into "societies" with a "common element of form" produces the organisms and inanimate things of ordinary sense experience. According to the proponents of string theory, tiny vibrating strings are the ultimate constituents of physical reality which in harmonious combination yield perceptible entities at the macroscopic level of physical reality. Given that the number of Whiteheadian actual entities and of individual strings within string theory are beyond reckoning at any given moment, could they be two ways to describe the same non-verifiable foundational reality? For example, if one could establish that the "superject" or objective pattern of self- constitution of an actual entity vibrates at a specific frequency, its affinity with the individual strings of string theory would be striking. Likewise, if one were to claim that the size and complexity of Whiteheadian 'societies" require different space-time parameters for the dynamic interrelationship of constituent actual entities, would that at least partially account for the assumption of 10 or even 26 instead of just 3 dimensions within string theory? The overall conclusion of this article is that, if a suitably revised understanding of Whiteheadian metaphysics were seen as compatible with the philosophical implications of string theory, their combination into a single world view would strengthen the plausibility of both schemes taken separately. Key words: actual entities, subject/superjects, vibrating strings, structured fields of activity, multi-dimensional physical reality.

  17. Catalytic combustion of actual low and medium heating value gases

    NASA Technical Reports Server (NTRS)

    Bulzan, D. L.

    1982-01-01

    Catalytic combustion of both low and medium heating value gases using actual coal derived gases obtained from operating gasifiers was demonstrated. A fixed bed gasifier with a complete product gas cleanup system was operated in an air blown mode to produce low heating value gas. A fluidized bed gasifier with a water quench product gas cleanup system was operated in both an air enriched and an oxygen blown mode to produce low and medium, heating value gas. Noble metal catalytic reactors were evaluated in 12 cm flow diameter test rigs on both low and medium heating value gases. Combustion efficiencies greater than 99.5% were obtained with all coal derived gaseous fuels. The NOx emissions ranged from 0.2 to 4 g NO2 kg fuel.

  18. The nonrelativistic limit of (central-extended) Poincare group and some consequences for quantum actualization

    SciTech Connect

    Ardenghi, Juan S.; Castagnino, M.; Campoamor-Stursberg, R.

    2009-10-15

    The nonrelativistic limit of the centrally extended Poincare group is considered and their consequences in the modal Hamiltonian interpretation of quantum mechanics are discussed [O. Lombardi and M. Castagnino, Stud. Hist. Philos. Mod. Phys 39, 380 (2008); J. Phys, Conf. Ser. 128, 012014 (2008)]. Through the assumption that in quantum field theory the Casimir operators of the Poincare group actualize, the nonrelativistic limit of the latter group yields to the actualization of the Casimir operators of the Galilei group, which is in agreement with the actualization rule of previous versions of modal Hamiltonian interpretation [Ardenghi et al., Found. Phys. (submitted)].

  19. Research on an expert system for database operation of simulation-emulation math models. Volume 2, Phase 1: Results

    NASA Technical Reports Server (NTRS)

    Kawamura, K.; Beale, G. O.; Schaffer, J. D.; Hsieh, B. J.; Padalkar, S.; Rodriguez-Moscoso, J. J.

    1985-01-01

    A reference manual is provided for NESS, a simulation expert system. This manual gives user information regarding starting and operating NASA expert simulation system (NESS). This expert system provides an intelligent interface to a generic simulation program for spacecraft attitude control problems. A menu of the functions the system can perform is provided. Control repeated returns to this menu after executing each user request.

  20. The Actual Apollo 13 Prime Crew

    NASA Technical Reports Server (NTRS)

    1970-01-01

    The actual Apollo 13 lunar landing mission prime crew from left to right are: Commander, James A. Lovell Jr., Command Module pilot, John L. Swigert Jr.and Lunar Module pilot, Fred W. Haise Jr. The original Command Module pilot for this mission was Thomas 'Ken' Mattingly Jr. but due to exposure to German measles he was replaced by his backup, Command Module pilot, John L. 'Jack' Swigert Jr.

  1. [On vibration hazards of chipping-hammer operators in an iron foundry. Part 2. Results of the hygienic control].

    PubMed

    Harada, N; Matsumoto, T; Yamada, S; Kobayashi, F

    1982-01-01

    We previously reported that the working and health conditions of vibrating tool operators in an iron foundry were investigated in 1975 and vibration hazards were observed to occur frequently in workers operating chipping-hammers powered by compressed air. After that, we instituted medical treatment for the afflicted workers and improvement of working conditions in the foundry, and have performed annual medical examinations for four years. In this paper, the course of hygienic control and the change in the medical findings of twenty-four chipping-hammer operators are reported. 1. The following measures were taken to improve the working conditions of chipping-hammer operators and therapy for patients (Table 1): (1) The operating time of vibrating tools, including chipping-hammer, was limited to two hours per day. The casting process was improved to diminish the flashes that are the objects of chipping-hammer operation. For the purpose of reducing the vibration transmitted to the operator, a servo-arm that has a servomechanism for the chipping-hammer was developed and introduced. (2) Infrared lamps in the foundry and air curtains at the doorway were installed for keeping the chipping-hammer operating area warm. A warm room was set up in the foundry for providing warmth during rest periods and protective clothing against the cold was provided. (3) Workers who displayed health disturbances by medical examinations were treated during the cold season from November to April by periodic visits to the clinic or extended hospitalization, or transferred to job without vibration exposure, according to their stage of disease. Preventive treatment with vasodilator and bubble bath was performed in winter for the chipping-hammer operators. 2. In order to estimate the effect of these countermeasures, annual medical examinations were conducted in March 1975, March 1976, April 1977 and March 1978. Such subjective symptoms as Raynaud's phenomenon, finger numbness, finger listlessness

  2. Long-term effects of dredging operations program. Effects of sediment organic-matter composition on bioaccumulation of sediment organic contaminants: Interim results. Final report

    SciTech Connect

    Brannon, J.M.; Price, C.B.; Reilly, F.J.; Pennington, J.C.; McFarland, V.A.

    1991-06-01

    The relationship of sediment-bound polychlorinated biphenyl (PCB) 153 and fluoranthene to bioaccumulation by worms and clams and the relationship of sediment-bound PCB 153 and fluoranthene to concentrations in the interstitial water were examined. Bioaccumulation by both worms and clams was observed in all sediments. Apparent preference factor (APF) values showed that steady state was reached between sediment-bound contaminants and organism lipid pools. The APF values of organisms were close to the theoretical value for both contaminants in all sediments. These results showed that sediment total organic carbon (TOC) in conjunction with octanol water partition coefficients of nonpolar organic contaminants is a viable approach for predicting bioaccumulation of such compounds by infaunal organisms. Actual concentrations of contaminants in interstitial water were either overestimated or underestimated by the relationship between TOC and humic + fulvic acid organic matter fractions and sediment contaminant concentrations. Prediction of interstitial water concentrations was not as successful as use of APFs. The lack of agreement between predicted and actual interstitial water results was due to factors such as the presence of interstitial water contaminants bounds to microparticulates and dissolved organic material and the kind of organic material in the sediment.

  3. NASA Desert RATS 2010: Preliminary Results for Science Operations Conducted in the San Francisco Volcanic Field, Arizona

    NASA Technical Reports Server (NTRS)

    Gruener, J. E.; Lofgren, G. E.; Bluethmann, W. J.; Bell, E. R.

    2011-01-01

    The National Aeronautics and Space Administration (NASA) is working with international partners to develop the space architectures and mission plans necessary for human spaceflight beyond earth orbit. These mission plans include the exploration of planetary surfaces with significant gravity fields. The Apollo missions to the Moon demonstrated conclusively that surface mobility is a key asset that improves the efficiency of human explorers on a planetary surface. NASA's Desert Research and Technology Studies (Desert RATS) is a multi-year series tests of hardware and operations carried out annually in the high desert of Arizona. Conducted since 1998, these activities are designed to exercise planetary surface hardware and operations in relatively harsh climatic conditions where long-distance, multi-day roving is achievable

  4. [Operation to promote use of long-lasting insecticidal nets (LLIN) in French Guiana in 2006: design, implementation and results].

    PubMed

    Mansotte, F; Ravachol, F; Carlisi, R; Caudal, J; Pinchon, S; Maison, D

    2010-06-01

    In 2006, the Regional Health Office (DSDS) in French Guiana undertook a major operation involving importation and distribution of long-lasting insecticide treated nets (LLIN/ITN). In collaboration with the WHO, a Vietnamese manufacturer of LLINs suited to the requirements of French Guiana was sourced. With the help of a dynamic local importer and dealer, a sales network was developed through chemist shops located all over French Guiana. This network provided wide coverage since these outlets can be found in all large communities. The selling price ranged from 15 to 23 euros depending on the model, i.e., hammock or bed size. In addition, LLINs were distributed within the framework of two special programs. First they are given to women giving birth in French Guiana and undergoing medical surveillance as part of the Mother and Child Protection program by public healthcare system. Second they are distributed in case of natural disaster or other events that could lead to an increased risk of vector-borne outbreaks. Thanks to this operation, a total of 13,882 LLINs were delivered in French Guiana from July 2006 to December 2008. This milestone operation in the fight against malaria was made possible thanks to funding granted on a one-time basis after the outbreak of dengue in 2005-2006. The structure of this operation and its survival will depend on the continued goodwill and determination of a small group of local partners who created this successful distribution campaign with no specific guidance or program from the national authorities. PMID:20734592

  5. An insight into actual energy use and its drivers in high-performance buildings

    SciTech Connect

    Li, Cheng; Hong, Tianzhen; Yan, Da

    2014-07-12

    Using portfolio analysis and individual detailed case studies, we studied the energy performance and drivers of energy use in 51 high-performance office buildings in the U.S., Europe, China, and other parts of Asia. Portfolio analyses revealed that actual site energy use intensity (EUI) of the study buildings varied by a factor of as much as 11, indicating significant variation in real energy use in HPBs worldwide. Nearly half of the buildings did not meet the American Society of Heating, Refrigerating, and Air Conditioning Engineers (ASHRAE) Standard 90.1-2004 energy target, raising questions about whether a building’s certification as high performing accurately indicates that a building is energy efficient and suggesting that improvement in the design and operation of HPBs is needed to realize their energy-saving potential. We studied the influence of climate, building size, and building technologies on building energy performance and found that although all are important, none are decisive factors in building energy use. EUIs were widely scattered in all climate zones. There was a trend toward low energy use in small buildings, but the correlation was not absolute; some small HPBs exhibited high energy use, and some large HPBs exhibited low energy use. We were unable to identify a set of efficient technologies that correlated directly to low EUIs. In two case studies, we investigated the influence of occupant behavior as well as operation and maintenance on energy performance and found that both play significant roles in realizing energy savings. We conclude that no single factor determines the actual energy performance of HPBs, and adding multiple efficient technologies does not necessarily improve building energy performance; therefore, an integrated design approach that takes account of climate, technology, occupant behavior, and operations and maintenance practices should be implemented to maximize energy savings in HPBs. As a result, these findings are

  6. An insight into actual energy use and its drivers in high-performance buildings

    DOE PAGESBeta

    Li, Cheng; Hong, Tianzhen; Yan, Da

    2014-07-12

    Using portfolio analysis and individual detailed case studies, we studied the energy performance and drivers of energy use in 51 high-performance office buildings in the U.S., Europe, China, and other parts of Asia. Portfolio analyses revealed that actual site energy use intensity (EUI) of the study buildings varied by a factor of as much as 11, indicating significant variation in real energy use in HPBs worldwide. Nearly half of the buildings did not meet the American Society of Heating, Refrigerating, and Air Conditioning Engineers (ASHRAE) Standard 90.1-2004 energy target, raising questions about whether a building’s certification as high performing accuratelymore » indicates that a building is energy efficient and suggesting that improvement in the design and operation of HPBs is needed to realize their energy-saving potential. We studied the influence of climate, building size, and building technologies on building energy performance and found that although all are important, none are decisive factors in building energy use. EUIs were widely scattered in all climate zones. There was a trend toward low energy use in small buildings, but the correlation was not absolute; some small HPBs exhibited high energy use, and some large HPBs exhibited low energy use. We were unable to identify a set of efficient technologies that correlated directly to low EUIs. In two case studies, we investigated the influence of occupant behavior as well as operation and maintenance on energy performance and found that both play significant roles in realizing energy savings. We conclude that no single factor determines the actual energy performance of HPBs, and adding multiple efficient technologies does not necessarily improve building energy performance; therefore, an integrated design approach that takes account of climate, technology, occupant behavior, and operations and maintenance practices should be implemented to maximize energy savings in HPBs. As a result, these

  7. Operational results of shaft repair by installing stave type cooler at Kimitsu Nos. 3 and 4 blast furnaces

    SciTech Connect

    Oda, Hiroshi; Amano, Shigeru; Sakamoto, Aiichiro; Anzai, Osamu; Nakagome, Michiru; Kuze, Toshisuke; Imuta, Akira

    1997-12-31

    Nos. 3 and 4 blast furnaces in Nippon Steel Corporation Kimitsu Works were both initially fitted with cooling plate systems. With the aging of each furnace, the damage to their respective inner-shaft profiles had become serious. Thus, in order to prevent operational change and prolong the furnace life, the inner-shaft profile of each furnace was repaired by replacing the former cooling plate system with the stave type cooler during the two-week-shutdowns. With this repair, stability of burden descent and gas flow near the wall part of the furnace have been achieved. Thus the prolongation of the furnace life is naturally expected.

  8. Operating cost model for local service airlines

    NASA Technical Reports Server (NTRS)

    Anderson, J. L.; Andrastek, D. A.

    1976-01-01

    Several mathematical models now exist which determine the operating economics for a United States trunk airline. These models are valuable in assessing the impact of new aircraft into an airline's fleet. The use of a trunk airline cost model for the local service airline does not result in representative operating costs. A new model is presented which is representative of the operating conditions and resultant costs for the local service airline. The calculated annual direct and indirect operating costs for two multiequipment airlines are compared with their actual operating experience.

  9. Air resistance measurements on actual airplane parts

    NASA Technical Reports Server (NTRS)

    Weiselsberger, C

    1923-01-01

    For the calculation of the parasite resistance of an airplane, a knowledge of the resistance of the individual structural and accessory parts is necessary. The most reliable basis for this is given by tests with actual airplane parts at airspeeds which occur in practice. The data given here relate to the landing gear of a Siemanms-Schuckert DI airplane; the landing gear of a 'Luftfahrzeug-Gesellschaft' airplane (type Roland Dlla); landing gear of a 'Flugzeugbau Friedrichshafen' G airplane; a machine gun, and the exhaust manifold of a 269 HP engine.

  10. Evaluating the improvements of the BOLAM meteorological model operational at ISPRA: A case study approach - preliminary results

    NASA Astrophysics Data System (ADS)

    Mariani, S.; Casaioli, M.; Lastoria, B.; Accadia, C.; Flavoni, S.

    2009-04-01

    The Institute for Environmental Protection and Research - ISPRA (former Agency for Environmental Protection and Technical Services - APAT) runs operationally since 2000 an integrated meteo-marine forecasting chain, named the Hydro-Meteo-Marine Forecasting System (Sistema Idro-Meteo-Mare - SIMM), formed by a cascade of four numerical models, telescoping from the Mediterranean basin to the Venice Lagoon, and initialized by means of analyses and forecasts from the European Centre for Medium-Range Weather Forecasts (ECMWF). The operational integrated system consists of a meteorological model, the parallel verision of BOlogna Limited Area Model (BOLAM), coupled over the Mediterranean sea with a WAve Model (WAM), a high-resolution shallow-water model of the Adriatic and Ionian Sea, namely the Princeton Ocean Model (POM), and a finite-element version of the same model (VL-FEM) on the Venice Lagoon, aimed to forecast the acqua alta events. Recently, the physically based, fully distributed, rainfall-runoff TOPographic Kinematic APproximation and Integration (TOPKAPI) model has been integrated into the system, coupled to BOLAM, over two river basins, located in the central and northeastern part of Italy, respectively. However, at the present time, this latter part of the forecasting chain is not operational and it is used in a research configuration. BOLAM was originally implemented in 2000 onto the Quadrics parallel supercomputer (and for this reason referred to as QBOLAM, as well) and only at the end of 2006 it was ported (together with the other operational marine models of the forecasting chain) onto the Silicon Graphics Inc. (SGI) Altix 8-processor machine. In particular, due to the Quadrics implementation, the Kuo scheme was formerly implemented into QBOLAM for the cumulus convection parameterization. On the contrary, when porting SIMM onto the Altix Linux cluster, it was achievable to implement into QBOLAM the more advanced convection parameterization by Kain and

  11. Structural Analysis Results of Thermal, Operating and Seismic Analysis for Hanford Single-Shell Tank Integrity - 12261

    SciTech Connect

    Pilli, Siva P.; Rinker, Michael W.

    2012-07-01

    Since Hanford's 149 Single-Shell Tanks (SSTs) are well beyond their design life, the U.S. Department of Energy has commissioned a state of the art engineering analysis to assess the structural integrity of the tanks to ensure that they are fit for service during the cleanup and closure phase. The structural integrity analysis has several challenging factors. There are four different tank sizes in various configurations that require analysis. Within each tank type there are different waste level and temperature histories, soil overburden depths, tank floor arrangements, riser sizes and locations, and other on-tank structures that need to be addressed. Furthermore, soil properties vary throughout the tank farms. This paper describes the structural integrity analysis that was performed for the SSTs using finite element models that incorporate the detailed design features of each tank type. The analysis was performed with two different models: an ANSYS static model for the Thermal and Operating Loads Analysis, and an ANSYS dynamic model for the seismic analysis. The TOLA analyses simulate the waste level and thermal history and it included a matrix of analysis cases that bounded the material property uncertainties. The TOLA also predicts the occurrence of concrete thermal degradations and cracking, reinforcement yielding, and soil plasticity. The seismic analysis matrix included uncertainty in waste properties, waste height and the soil modulus. In seismic analysis the tank concrete was modeled as a linear elastic material that was adjusted for the present day degraded conditions. Also, the soil was treated as a linear elastic material while special modeling techniques were used to avoid soil arching and achieve proper soil pressure on the tank walls. Seismic time histories in both the horizontal and vertical directions were applied to the seismic model. Structural demands from both Thermal and Operating Loads Analysis and seismic models were extracted in the form of

  12. Results from the Operational Testing of the General Electric Smart Grid Capable Electric Vehicle Supply Equipment (EVSE)

    SciTech Connect

    Richard Barney Carlson; Don Scoffield; Brion Bennett

    2013-12-01

    The Idaho National Laboratory conducted testing and analysis of the General Electric (GE) smart grid capable electric vehicle supply equipment (EVSE), which was a deliverable from GE for the U.S. Department of Energy FOA-554. The Idaho National Laboratory has extensive knowledge and experience in testing advanced conductive and wireless charging systems though INL’s support of the U.S. Department of Energy’s Advanced Vehicle Testing Activity. This document details the findings from the EVSE operational testing conducted at the Idaho National Laboratory on the GE smart grid capable EVSE. The testing conducted on the EVSE included energy efficiency testing, SAE J1772 functionality testing, abnormal conditions testing, and charging of a plug-in vehicle.

  13. Commissioning and operational results of helium refrigeration system at JLab for the 12GeV upgrade

    SciTech Connect

    Knudsen, Peter N.; Ganni, Venkatarao; Dixon, Kelly D.; Norton, Robert O.; Creel, Jonathan D.

    2015-12-01

    The new 4.5 K refrigerator system at the Jefferson Lab (JLab) Central Helium Liquefier (CHL-2) for the 12 GeV upgrade was commissioned in late spring of 2013, following the commissioning of the new compressor system, and has been supporting 12 GeV LINAC commissioning since that time. Six design modes were tested during commissioning, consisting of a maximum capacity, nominal capacity, maximum liquefaction, maximum refrigeration, maximum fill and a stand-by/reduced load condition. The maximum capacity was designed to support a 238 g/s, 30 K and 1.16 bar cold compressor return flow, a 15 g/s, 4.5 K liquefaction load and a 12.6 kW, 35-55 K shield load. The other modes were selected to ensure proper component sizing and selection to allow the cold box to operate over a wide range of conditions and capacities. The cold box system is comprised of two physically independent cold boxes with interconnecting transfer-lines. The outside (upper) 300-60 K vertical cold box has no turbines and incorporates a liquid nitrogen pre-cooler and 80-K beds. The inside (lower) 60-4.5 K horizontal cold box houses seven turbines that are configured in four expansion stages including one Joule-Thompson expander and a 20-K bed. The helium compression system has five compressors to support three pressure levels in the cold box. This paper will summarize the analysis of the test data obtained over the wide range of operating conditions and capacities which were tested.

  14. First Dark Matter Search Results from a 4-kg CF$_3$I Bubble Chamber Operated in a Deep Underground Site

    SciTech Connect

    Behnke, E.; Behnke, J.; Brice, S.J.; Broemmelsiek, D.; Collar, J.I.; Conner, A.; Cooper, P.S.; Crisler, M.; Dahl, C.E.; Fustin, D.; Grace, E.; /Indiana U., South Bend /Fermilab

    2012-04-01

    New data are reported from the operation of a 4.0 kg CF{sub 3}I bubble chamber in the 6800 foot deep SNOLAB underground laboratory. The effectiveness of ultrasound analysis in discriminating alpha decay background events from single nuclear recoils has been confirmed, with a lower bound of >99.3% rejection of alpha decay events. Twenty single nuclear recoil event candidates and three multiple bubble events were observed during a total exposure of 553 kg-days distributed over three different bubble nucleation thresholds. The effective exposure for single bubble recoil-like events was 437.4 kg-days. A neutron background internal to the apparatus, of known origin, is estimated to account for five single nuclear recoil events and is consistent with the observed rate of multiple bubble events. This observation provides world best direct detection constraints on WIMP-proton spin-dependent scattering for WIMP masses >20 GeV/c{sup 2} and demonstrates significant sensitivity for spin-independent interactions.

  15. Heat transfer results and operational characteristics of the NASA Lewis Research Center Hot Section Cascade Test Facility

    NASA Technical Reports Server (NTRS)

    Gladden, H. J.; Yeh, F. C.; Fronek, D. L.

    1985-01-01

    The NASA Lewis Research Center gas turbine hot section test facility has been developed to provide a real-engine environment with well known boundary conditions for the aerothermal performance evaluation/verification of computer design codes. The initial aerothermal research data obtained are presented and the operational characteristics of the facility are discussed. This facility is capable of testing at temperatures and pressures up to 1600 K and 18 atm which corresponds to a vane exit Reynolds number range of 0.5x10(6) to 2.5x10(6) based on vane chord. The component cooling air temperature can be independently modulated between 330 and 700 K providing gas-to-coolant temperature ratios similar to current engine application. Research instrumentation of the test components provide conventional pressure and temperature measurements as well as metal temperatures measured by IR-photography. The primary data acquisition mode is steady state through a 704 channel multiplexer/digitizer. The test facility was configured as an annular cascade of full coverage filmcooled vanes for the initial series of research tests.

  16. First dark matter search results from a 4-kg CF3I bubble chamber operated in a deep underground site

    NASA Astrophysics Data System (ADS)

    Behnke, E.; Behnke, J.; Brice, S. J.; Broemmelsiek, D.; Collar, J. I.; Conner, A.; Cooper, P. S.; Crisler, M.; Dahl, C. E.; Fustin, D.; Grace, E.; Hall, J.; Hu, M.; Levine, I.; Lippincott, W. H.; Moan, T.; Nania, T.; Ramberg, E.; Robinson, A. E.; Sonnenschein, A.; Szydagis, M.; Vázquez-Jáuregui, E.

    2012-09-01

    New data are reported from the operation of a 4.0-kg CF3I bubble chamber in the 6800-foot-deep SNOLAB underground laboratory. The effectiveness of ultrasound analysis in discriminating alpha-decay background events from single nuclear recoils has been confirmed, with a lower bound of >99.3% rejection of alpha-decay events. Twenty single nuclear recoil event candidates and three multiple bubble events were observed during a total exposure of 553 kg-days distributed over three different bubble nucleation thresholds. The effective exposure for single bubble recoil-like events was 437.4 kg-days. A neutron background internal to the apparatus, of known origin, is estimated to account for five single nuclear recoil events and is consistent with the observed rate of multiple bubble events. The remaining excess of single bubble events exhibits characteristics indicating the presence of an additional background. These data provide new direct detection constraints on WIMP-proton spin-dependent scattering for WIMP masses >20GeV/c2 and demonstrate significant sensitivity for spin-independent interactions.

  17. 7 CFR 1437.101 - Actual production history.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Actual production history. 1437.101 Section 1437.101... Determining Yield Coverage Using Actual Production History § 1437.101 Actual production history. Actual production history (APH) is the unit's record of crop yield by crop year for the APH base period. The...

  18. 7 CFR 1437.101 - Actual production history.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Actual production history. 1437.101 Section 1437.101... Determining Yield Coverage Using Actual Production History § 1437.101 Actual production history. Actual production history (APH) is the unit's record of crop yield by crop year for the APH base period. The...

  19. 7 CFR 1437.101 - Actual production history.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Actual production history. 1437.101 Section 1437.101... Determining Yield Coverage Using Actual Production History § 1437.101 Actual production history. Actual production history (APH) is the unit's record of crop yield by crop year for the APH base period. The...

  20. 7 CFR 1437.101 - Actual production history.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false Actual production history. 1437.101 Section 1437.101... Determining Yield Coverage Using Actual Production History § 1437.101 Actual production history. Actual production history (APH) is the unit's record of crop yield by crop year for the APH base period. The...

  1. 7 CFR 1437.101 - Actual production history.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Actual production history. 1437.101 Section 1437.101... Determining Yield Coverage Using Actual Production History § 1437.101 Actual production history. Actual production history (APH) is the unit's record of crop yield by crop year for the APH base period. The...

  2. Actual curriculum development practices instrument: Testing for factorial validity

    NASA Astrophysics Data System (ADS)

    Foi, Liew Yon; Bakar, Kamariah Abu; Hamzah, Mohd Sahandri Gani; Alwi, Nor Hayati

    2014-09-01

    The Actual Curriculum Development Practices Instrument (ACDP-I) was developed and the factorial validity of the ACDP-I was tested (n = 107) using exploratory factor analysis procedures in the earlier work of [1]. Despite the ACDP-I appears to be content and construct valid instrument with very high internal reliability qualities for using in Malaysia, the accumulated evidences are still needed to provide a sound scientific basis for the proposed score interpretations. Therefore, the present study addresses this concern by utilising the confirmatory factor analysis to further confirm the theoretical structure of the variable Actual Curriculum Development Practices (ACDP) and enrich the psychometrical properties of ACDP-I. Results of this study have practical implication to both researchers and educators whose concerns focus on teachers' classroom practices and the instrument development and validation process.

  3. Sonic boom results for a nominal mission 3B. Space Shuttle engineering and operations support, engineering systems analysis

    NASA Technical Reports Server (NTRS)

    1975-01-01

    The results obtained in the analysis of the effects of sonic boom overpressures at ground level for a nominal Mission 3B with the current baseline guidance are reported. These results are in the form of ground level overpressures generated along the groundtrack out to lateral cutoff from Mach 3.0-1.10 at 0.10 (tenth) Mach intervals. Preliminary trajectory constraints which will reduce excess sonic boom overpressures to approximately 2.0 PSF are included.

  4. The actual status of Astronomy in Moldova

    NASA Astrophysics Data System (ADS)

    Gaina, A.

    The astronomical research in the Republic of Moldova after Nicolae Donitch (Donici)(1874-1956(?)) were renewed in 1957, when a satellites observations station was open in Chisinau. Fotometric observations and rotations of first Soviet artificial satellites were investigated under a program SPIN put in action by the Academy of Sciences of former Socialist Countries. The works were conducted by Assoc. prof. Dr. V. Grigorevskij, which conducted also research in variable stars. Later, at the beginning of 60-th, an astronomical Observatory at the Chisinau State University named after Lenin (actually: the State University of Moldova), placed in Lozovo-Ciuciuleni villages was open, which were coordinated by Odessa State University (Prof. V.P. Tsesevich) and the Astrosovet of the USSR. Two main groups worked in this area: first conducted by V. Grigorevskij (till 1971) and second conducted by L.I. Shakun (till 1988), both graduated from Odessa State University. Besides this research areas another astronomical observations were made: Comets observations, astroclimate and atmospheric optics in collaboration with the Institute of the Atmospheric optics of the Siberian branch of the USSR (V. Chernobai, I. Nacu, C. Usov and A.F. Poiata). Comets observations were also made since 1988 by D. I. Gorodetskij which came to Chisinau from Alma-Ata and collaborated with Ukrainean astronomers conducted by K.I. Churyumov. Another part of space research was made at the State University of Tiraspol since the beggining of 70-th by a group of teaching staff of the Tiraspol State Pedagogical University: M.D. Polanuer, V.S. Sholokhov. No a collaboration between Moldovan astronomers and Transdniestrian ones actually exist due to War in Transdniestria in 1992. An important area of research concerned the Radiophysics of the Ionosphere, which was conducted in Beltsy at the Beltsy State Pedagogical Institute by a group of teaching staff of the University since the beginning of 70-th: N. D. Filip, E

  5. What Galvanic Vestibular Stimulation Actually Activates

    PubMed Central

    Curthoys, Ian S.; MacDougall, Hamish Gavin

    2012-01-01

    In a recent paper in Frontiers Cohen et al. (2012) asked “What does galvanic vestibular stimulation actually activate?” and concluded that galvanic vestibular stimulation (GVS) causes predominantly otolithic behavioral responses. In this Perspective paper we show that such a conclusion does not follow from the evidence. The evidence from neurophysiology is very clear: galvanic stimulation activates primary otolithic neurons as well as primary semicircular canal neurons (Kim and Curthoys, 2004). Irregular neurons are activated at lower currents. The answer to what behavior is activated depends on what is measured and how it is measured, including not just technical details, such as the frame rate of video, but the exact experimental context in which the measurement took place (visual fixation vs total darkness). Both canal and otolith dependent responses are activated by GVS. PMID:22833733

  6. MODIS Solar Diffuser: Modelled and Actual Performance

    NASA Technical Reports Server (NTRS)

    Waluschka, Eugene; Xiong, Xiao-Xiong; Esposito, Joe; Wang, Xin-Dong; Krebs, Carolyn (Technical Monitor)

    2001-01-01

    The Moderate Resolution Imaging Spectroradiometer (MODIS) instrument's solar diffuser is used in its radiometric calibration for the reflective solar bands (VIS, NTR, and SWIR) ranging from 0.41 to 2.1 micron. The sun illuminates the solar diffuser either directly or through a attenuation screen. The attenuation screen consists of a regular array of pin holes. The attenuated illumination pattern on the solar diffuser is not uniform, but consists of a multitude of pin-hole images of the sun. This non-uniform illumination produces small, but noticeable radiometric effects. A description of the computer model used to simulate the effects of the attenuation screen is given and the predictions of the model are compared with actual, on-orbit, calibration measurements.

  7. 30 CFR 206.180 - How do I determine an actual processing allowance?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) When MMS conducts reviews and audits, we will examine whether the contract reflects more than the...-contract situation are subject to monitoring, review, audit, and adjustment. You must submit the actual... processing plant. (i) Allowable operating expenses include operations supervision and engineering,...

  8. The Operational MODIS Cloud Optical and Microphysical Property Product: Overview of the Collection 6 Algorithm and Preliminary Results

    NASA Technical Reports Server (NTRS)

    Platnick, Steven; King, Michael D.; Wind, Galina; Amarasinghe, Nandana; Marchant, Benjamin; Arnold, G. Thomas

    2012-01-01

    Operational Moderate Resolution Imaging Spectroradiometer (MODIS) retrievals of cloud optical and microphysical properties (part of the archived products MOD06 and MYD06, for MODIS Terra and Aqua, respectively) are currently being reprocessed along with other MODIS Atmosphere Team products. The latest "Collection 6" processing stream, which is expected to begin production by summer 2012, includes updates to the previous cloud retrieval algorithm along with new capabilities. The 1 km retrievals, based on well-known solar reflectance techniques, include cloud optical thickness, effective particle radius, and water path, as well as thermodynamic phase derived from a combination of solar and infrared tests. Being both global and of high spatial resolution requires an algorithm that is computationally efficient and can perform over all surface types. Collection 6 additions and enhancements include: (i) absolute effective particle radius retrievals derived separately from the 1.6 and 3.7 !-lm bands (instead of differences relative to the standard 2.1 !-lm retrieval), (ii) comprehensive look-up tables for cloud reflectance and emissivity (no asymptotic theory) with a wind-speed interpolated Cox-Munk BRDF for ocean surfaces, (iii) retrievals for both liquid water and ice phases for each pixel, and a subsequent determination of the phase based, in part, on effective radius retrieval outcomes for the two phases, (iv) new ice cloud radiative models using roughened particles with a specified habit, (v) updated spatially-complete global spectral surface albedo maps derived from MODIS Collection 5, (vi) enhanced pixel-level uncertainty calculations incorporating additional radiative error sources including the MODIS L1 B uncertainty index for assessing band and scene-dependent radiometric uncertainties, (v) and use of a new 1 km cloud top pressure/temperature algorithm (also part of MOD06) for atmospheric corrections and low cloud non-unity emissivity temperature adjustments.

  9. Cryogenic Absorption Cells Operating Inside a Bruker IFS-125HR: First Results for 13CH4 at 7 Micrometers

    NASA Technical Reports Server (NTRS)

    Sung, K.; Mantz, A. W.; Smith, M. A. H.; Brown, L. R.; Crawford, T. J.; Devi, V. M.; Benner, D. C.

    2010-01-01

    New absorption cells designed specifically to achieve stable temperatures down to 66 K inside the sample compartment of an evacuated Bruker IFS-125HR Fourier transform spectrometer (FTS) were developed at Connecticut College and tested at the Jet Propulsion Laboratory (JPL). The temperature stabilized cryogenic cells with path lengths of 24.29 and 20.38 cm were constructed of oxygen free high conductivity (OFHC) copper and fitted with wedged ZnSe windows using vacuum tight indium seals. In operation, the temperature-controlled cooling by a closed-cycle helium refrigerator achieved stability of 0.01 K. The unwanted absorption features arising from cryodeposits on the cell windows at low temperatures were eliminated by building an internal vacuum shroud box around the cell which significantly minimized the growth of cryodeposits. The effects of vibrations from the closed-cycle helium refrigerator on the FTS spectra were characterized. Using this set up, several high-resolution spectra of methane isotopologues broadened with nitrogen were recorded in the 1200-1800 per centimeter spectral region at various sample temperatures between 79.5 and 296 K. Such data are needed to characterize the temperature dependence of spectral line shapes at low temperatures for remote sensing of outer planets and their moons. Initial analysis of a limited number of spectra in the region of the R(2) manifold of the v4 fundamental band of 13CH4 indicated that an empirical power law used for the temperature dependence of the N2-broadened line widths would fail to fit the observed data in the entire temperature range from 80 to 296 K; instead, it follows a temperature-dependence similar to that reported by Mondelain et al. [17,18]. The initial test was very successful proving that a high precision Fourier transform spectrometer with a completely evacuated optical path can be configured for spectroscopic studies at low temperatures relevant to the planetary atmospheres.

  10. 17 CFR 229.303 - (Item 303) Management's discussion and analysis of financial condition and results of operations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Regulation S-X (17 CFR 210), a management's discussion and analysis of the financial condition and results of... is not excluded from the initial recognition and measurement provisions of FIN 45 pursuant to... or credit risk support to, or engages in leasing, hedging or research and development services...

  11. NHEXAS PHASE I MARYLAND STUDY--STANDARD OPERATING PROCEDURE FOR LAB RESULTS DATA ENTRY AND PREPARATION (D03)

    EPA Science Inventory

    The purpose of this SOP is to describe how lab results are organized and processed into the official database known as the Complete Dataset (CDS); to describe the structure and creation of the Analysis-ready Dataset (ADS); and to describe the structure and process of creating the...

  12. FIRST RESULTS FROM OPERATIONAL TESTING OF THE U.S. EPA MODELS-3 COMMUNITY MULTISCALE MODEL FOR AIR QUALITY (CMAQ)

    EPA Science Inventory

    The Models 3 / Community Multiscale Model for Air Quality (CMAQ) has been designed for one-atmosphere assessments for multiple pollutants including ozone (O3), particulate matter (PM10, PM2.5), and acid / nutrient deposition. In this paper we report initial results of our evalu...

  13. Tutorial on Actual Space Environmental Hazards For Space Systems (Invited)

    NASA Astrophysics Data System (ADS)

    Mazur, J. E.; Fennell, J. F.; Guild, T. B.; O'Brien, T. P.

    2013-12-01

    It has become common in the space science community to conduct research on diverse physical phenomena because they are thought to contribute to space weather. However, satellites contend with only three primary environmental hazards: single event effects, vehicle charging, and total dose, and not every physical phenomenon that occurs in space contributes in substantial ways to create these hazards. One consequence of the mismatch between actual threats and all-encompassing research is the often-described gap between research and operations; another is the creation of forecasts that provide no actionable information for design engineers or spacecraft operators. An example of the latter is the physics of magnetic field emergence on the Sun; the phenomenon is relevant to the formation and launch of coronal mass ejections and is also causally related to the solar energetic particles that may get accelerated in the interplanetary shock. Unfortunately for the research community, the engineering community mitigates the space weather threat (single-event effects from heavy ions above ~50 MeV/nucleon) with a worst-case specification of the environment and not with a prediction. Worst-case definition requires data mining of past events, while predictions involve large-scale systems science from the Sun to the Earth that is compelling for scientists and their funding agencies but not actionable for design or for most operations. Differing priorities among different space-faring organizations only compounds the confusion over what science research is relevant. Solar particle impacts to human crew arise mainly from the total ionizing dose from the solar protons, so the priority for prediction in the human spaceflight community is therefore much different than in the unmanned satellite community, while both communities refer to the fundamental phenomenon as space weather. Our goal in this paper is the presentation of a brief tutorial on the primary space environmental phenomena

  14. Monoclonal antibody panels for acute leukemia and myelodysplastic syndrome diagnosis. Results of a co-operative quality control group.

    PubMed

    Basso, G; Bernasconi, P; Chianese, R; Crovetti, G; Garbaccio, G; Iavarone, A; Pautasso, M; Santagostino, A; Stacchini, A

    2001-01-01

    The need for standardization criteria and result reproducibility in immunophenotyping hematological diseases has increased along with their clinical importance. Our group "Policentric Study Group on Immunological Markers", is composed of 40 laboratories. Its aim, over recent years, has been to find a standardized way of immunophenotypic analysis applicable to various hematological diseases. The objective of this study is to contribute to the debate concerning standardization of monoclonal antibody panels and immunophenotypic analysis procedures in acute leukemia (AL) and myelodysplastic syndrome (MDS), with the following targets: to improve interlaboratory reproducibility of the immunophenotyping data, and interpretative results; to study, with improved feasibility, correlation between immunophenotype and clinical or biological findings on a large number of AL and MDS cases; to verify the utility of the proposed monoclonal antibody panels for proper AL and MDS classification, and to detect minimal residual disease. In the field of AL and MDS our experience is based on about 1800 and 700 cases respectively analyzed over the last five years. Starting from these experiences and data of the literature we have elaborated the proposed panels of monoclonal antibodies and the methods of analysis. We have suggested a standardized immunophenotypic approach to study AL and MDS. In particular our work has focused on the gating strategy. This aims at drawing a gate of analysis having high purity and recovery, and on the choice of monoclonal antibody combinations for multiparametric analysis, particularly the normal antigen expression on each step of lineage differentiation or their clinically relevant aberrant expressions. A standardized criteria has become a necessary starting point in any kind of analytical process. In the field of acute leukemias and myelodysplastic syndromes the work of this polycentric group has focused on the pre-analytical and analytical steps to be

  15. PRA In Design: Increasing Confidence in Pre-operational Assessments of Risks (Results of a Joint NASA/ NRC Workshop)

    SciTech Connect

    Robert Youngblood

    2010-06-01

    In late 2009, the National Aeronautics and Space Administration (NASA) and the U.S. Nuclear Regulatory Commission (NRC) jointly organized a workshop to discuss technical issues associated with application of risk assessments to early phases of system design. The workshop, which was coordinated by the Idaho National Laboratory, involved invited presentations from a number of PRA experts in the aerospace and nuclear fields and subsequent discussion to address the following questions: (a) What technical issues limit decision-makers’ confidence in PRA results, especially at a preoperational phase of the system life cycle? (b) What is being done to address these issues? (c) What more can be done? The workshop resulted in participant observations and suggestions on several technical issues, including the pursuit of non-traditional approaches to risk assessment and the verification and validation of risk models. The workshop participants also identified several important non-technical issues, including risk communication with decision makers, and the integration of PRA into the overall design process.

  16. Caustic-Side Solvent Extraction: Prediction of Cesium Extraction for Actual Wastes and Actual Waste Simulants

    SciTech Connect

    Delmau, L.H.; Haverlock, T.J.; Sloop, F.V., Jr.; Moyer, B.A.

    2003-02-01

    This report presents the work that followed the CSSX model development completed in FY2002. The developed cesium and potassium extraction model was based on extraction data obtained from simple aqueous media. It was tested to ensure the validity of the prediction for the cesium extraction from actual waste. Compositions of the actual tank waste were obtained from the Savannah River Site personnel and were used to prepare defined simulants and to predict cesium distribution ratios using the model. It was therefore possible to compare the cesium distribution ratios obtained from the actual waste, the simulant, and the predicted values. It was determined that the predicted values agree with the measured values for the simulants. Predicted values also agreed, with three exceptions, with measured values for the tank wastes. Discrepancies were attributed in part to the uncertainty in the cation/anion balance in the actual waste composition, but likely more so to the uncertainty in the potassium concentration in the waste, given the demonstrated large competing effect of this metal on cesium extraction. It was demonstrated that the upper limit for the potassium concentration in the feed ought to not exceed 0.05 M in order to maintain suitable cesium distribution ratios.

  17. Ten Year Operating Test Results and Post-Test Analysis of a 1/10 Segment Stirling Sodium Heat Pipe, Phase III

    NASA Technical Reports Server (NTRS)

    Rosenfeld, John, H; Minnerly, Kenneth, G; Dyson, Christopher, M.

    2012-01-01

    High-temperature heat pipes are being evaluated for use in energy conversion applications such as fuel cells, gas turbine re-combustors, Stirling cycle heat sources; and with the resurgence of space nuclear power both as reactor heat removal elements and as radiator elements. Long operating life and reliable performance are critical requirements for these applications. Accordingly, long-term materials compatibility is being evaluated through the use of high-temperature life test heat pipes. Thermacore, Inc., has carried out a sodium heat pipe 10-year life test to establish long-term operating reliability. Sodium heat pipes have demonstrated favorable materials compatibility and heat transport characteristics at high operating temperatures in air over long time periods. A representative one-tenth segment Stirling Space Power Converter heat pipe with an Inconel 718 envelope and a stainless steel screen wick has operated for over 87,000 hr (10 yr) at nearly 700 C. These life test results have demonstrated the potential for high-temperature heat pipes to serve as reliable energy conversion system components for power applications that require long operating lifetime with high reliability. Detailed design specifications, operating history, and post-test analysis of the heat pipe and sodium working fluid are described.

  18. Numerical study of the SSME nozzle flow fields during transient operations: A comparison of the animated results with test

    NASA Astrophysics Data System (ADS)

    Wang, Ten-See; Dumas, Catherine

    1993-07-01

    A computational fluid dynamics (CFD) model has been applied to study the transient flow phenomena of the nozzle and exhaust plume of the Space Shuttle Main Engine (SSME), fired at sea level. The CFD model is a time accurate, pressure based, reactive flow solver. A six-species hydrogen/oxygen equilibrium chemistry is used to describe the chemical-thermodynamics. An adaptive upwinding scheme is employed for the spatial discretization, and a predictor, multiple corrector method is used for the temporal solution. Both engine start-up and shut-down processes were simulated. The elapse time is approximately five seconds for both cases. The computed results were animated and compared with the test. The images for the animation were created with PLOT3D and FAST and then animated with ABEKAS. The hysteresis effects, and the issues of free-shock separation, restricted-shock separation and the end-effects were addressed.

  19. Numerical study of the SSME nozzle flow fields during transient operations: A comparison of the animated results with test

    NASA Technical Reports Server (NTRS)

    Wang, Ten-See; Dumas, Catherine

    1993-01-01

    A computational fluid dynamics (CFD) model has been applied to study the transient flow phenomena of the nozzle and exhaust plume of the Space Shuttle Main Engine (SSME), fired at sea level. The CFD model is a time accurate, pressure based, reactive flow solver. A six-species hydrogen/oxygen equilibrium chemistry is used to describe the chemical-thermodynamics. An adaptive upwinding scheme is employed for the spatial discretization, and a predictor, multiple corrector method is used for the temporal solution. Both engine start-up and shut-down processes were simulated. The elapse time is approximately five seconds for both cases. The computed results were animated and compared with the test. The images for the animation were created with PLOT3D and FAST and then animated with ABEKAS. The hysteresis effects, and the issues of free-shock separation, restricted-shock separation and the end-effects were addressed.

  20. Measurements of Humidity in the Atmosphere and Validation Experiments (MOHAVE)-2009: overview of campaign operations and results

    NASA Astrophysics Data System (ADS)

    Leblanc, T.; Walsh, T. D.; McDermid, I. S.; Toon, G. C.; Blavier, J.-F.; Haines, B.; Read, W. G.; Herman, B.; Fetzer, E.; Sander, S.; Pongetti, T.; Whiteman, D. N.; McGee, T. G.; Twigg, L.; Sumnicht, G.; Venable, D.; Calhoun, M.; Dirisu, A.; Hurst, D.; Jordan, A.; Hall, E.; Miloshevich, L.; Vömel, H.; Straub, C.; Kampfer, N.; Nedoluha, G. E.; Gomez, R. M.; Holub, K.; Gutman, S.; Braun, J.; Vanhove, T.; Stiller, G.; Hauchecorne, A.

    2011-05-01

    The Measurements of Humidity in the Atmosphere and Validation Experiment (MOHAVE) 2009 campaign took place on 11-27 October 2009 at the JPL Table Mountain Facility in California (TMF). The main objectives of the campaign were to (1) validate the water vapor measurements of several instruments, including, three Raman lidars, two microwave radiometers, two Fourier-Transform spectrometers, and two GPS receivers (column water), (2) cover water vapor measurements from the ground to the mesopause without gaps, and (3) study upper tropospheric humidity variability at timescales varying from a few minutes to several days. A total of 58 radiosondes and 20 Frost-Point hygrometer sondes were launched. Two types of radiosondes were used during the campaign. Non negligible differences in the readings between the two radiosonde types used (Vaisala RS92 and InterMet iMet-1) made a small, but measurable impact on the derivation of water vapor mixing ratio by the Frost-Point hygrometers. As observed in previous campaigns, the RS92 humidity measurements remained within 5 % of the Frost-point in the lower and mid-troposphere, but were too dry in the upper troposphere. Over 270 h of water vapor measurements from three Raman lidars (JPL and GSFC) were compared to RS92, CFH, and NOAA-FPH. The JPL lidar profiles reached 20 km when integrated all night, and 15 km when integrated for 1 h. Excellent agreement between this lidar and the frost-point hygrometers was found throughout the measurement range, with only a 3 % (0.3 ppmv) mean wet bias for the lidar in the upper troposphere and lower stratosphere (UTLS). The other two lidars provided satisfactory results in the lower and mid-troposphere (2-5 % wet bias over the range 3-10 km), but suffered from contamination by fluorescence (wet bias ranging from 5 to 50 % between 10 km and 15 km), preventing their use as an independent measurement in the UTLS. The comparison between all available stratospheric sounders allowed to identify only the

  1. Measurements of Humidity in the Atmosphere and Validation Experiments (MOHAVE)-2009: overview of campaign operations and results

    NASA Astrophysics Data System (ADS)

    Leblanc, T.; Walsh, T. D.; McDermid, I. S.; Toon, G. C.; Blavier, J.-F.; Haines, B.; Read, W. G.; Herman, B.; Fetzer, E.; Sander, S.; Pongetti, T.; Whiteman, D. N.; McGee, T. G.; Twigg, L.; Sumnicht, G.; Venable, D.; Calhoun, M.; Dirisu, A.; Hurst, D.; Jordan, A.; Hall, E.; Miloshevich, L.; Vömel, H.; Straub, C.; Kampfer, N.; Nedoluha, G. E.; Gomez, R. M.; Holub, K.; Gutman, S.; Braun, J.; Vanhove, T.; Stiller, G.; Hauchecorne, A.

    2011-12-01

    The Measurements of Humidity in the Atmosphere and Validation Experiment (MOHAVE) 2009 campaign took place on 11-27 October 2009 at the JPL Table Mountain Facility in California (TMF). The main objectives of the campaign were to (1) validate the water vapor measurements of several instruments, including, three Raman lidars, two microwave radiometers, two Fourier-Transform spectrometers, and two GPS receivers (column water), (2) cover water vapor measurements from the ground to the mesopause without gaps, and (3) study upper tropospheric humidity variability at timescales varying from a few minutes to several days. A total of 58 radiosondes and 20 Frost-Point hygrometer sondes were launched. Two types of radiosondes were used during the campaign. Non negligible differences in the readings between the two radiosonde types used (Vaisala RS92 and InterMet iMet-1) made a small, but measurable impact on the derivation of water vapor mixing ratio by the Frost-Point hygrometers. As observed in previous campaigns, the RS92 humidity measurements remained within 5% of the Frost-point in the lower and mid-troposphere, but were too dry in the upper troposphere. Over 270 h of water vapor measurements from three Raman lidars (JPL and GSFC) were compared to RS92, CFH, and NOAA-FPH. The JPL lidar profiles reached 20 km when integrated all night, and 15 km when integrated for 1 h. Excellent agreement between this lidar and the frost-point hygrometers was found throughout the measurement range, with only a 3% (0.3 ppmv) mean wet bias for the lidar in the upper troposphere and lower stratosphere (UTLS). The other two lidars provided satisfactory results in the lower and mid-troposphere (2-5% wet bias over the range 3-10 km), but suffered from contamination by fluorescence (wet bias ranging from 5 to 50% between 10 km and 15 km), preventing their use as an independent measurement in the UTLS. The comparison between all available stratospheric sounders allowed to identify only the

  2. Pre-operative diclofenac HPβCD for pain control of needle biopsy in musculoskeletal neoplasm: preliminary results

    PubMed Central

    D’Arienzo, Antonio; Beltrami, Giovanni; Mancini, Daniele; Scoccianti, Guido; Cuomo, Pierluigi; Muratori, Francesco; Matera, Davide; Ippolito, Massimiliano; Mondanelli, Nicola; Frenos, Filippo; Totti, Francesca; Capanna, Rodolfo

    2015-01-01

    Summary Needle biopsy is the main standard method used for diagnosis of musculoskeletal tumors of the limbs and superficial trunk. Pain control during this procedure is through the use of Local Anaestetic (L.A.). In order to achieve a complete pain control in our cases, recently we started using diclofenac HPβCD 50 mg via s.c. preoperativly. We present the clinical results of a non-randomized study of two eterogeneous groups of patients: “Experimental” Group (1): diclofenac HPβCD 50 mg via s.c. one hour before surgical procedure, local anesthesia and ev. diclofenac HPβCD 50 mg via s.c. 12 hours postoperative; “Conventional” Group (2): local anesthesia and ev. postoperative tramadol 100 mg via oral for pain control. In October 2014, at the Department of Orthopedic Oncology and Reconstructive Surgery of Florence, 37 musculoskeletal biopsies for a bone or a soft tissue lesion were performed. Exclusion criteria for this study were: known allergies to lidocaine, diclofenac, tramadol; known gastric or duodenal ulcers; known gastrointestinal bleed or perforation; refusal of the patients to collaborate. For one or more of these reasons, 6 patients were excluded from this study. In the Group 1, 10 patients (59%) referred no pain during the surgical procedure (8/14 biopsies on soft tissue and 2/3 on bone). In 5 cases (29%) no exacerbation of previous chronic pain, and in 2 cases (12%) a progression of local pain after biopsy (average 1 points higher in the VAS). In Group 2, only 6 patients (42%) did not have any pain during the procedure, 4 (29%) no exacerbation of previous chronic pain and 4 (29%) a progression of local pain (average 2 points higher in the VAS). Despite similar results in both Groups, Group 1 seemed to have a mild better control of perioperative pain. The use of diclofenac HPβCD 50 mg preoperative seems to be a rational approach for minimizing perioperative pain and the preliminary data of our study seem encouraging. Obviously many bias are

  3. Benchmarks for Operative Outcomes of Robotic and Open Radical Prostatectomy: Results from the Health Professionals Follow-up Study

    PubMed Central

    Alemozaffar, Mehrdad; Sanda, Martin; Yecies, Derek; Mucci, Lorelei A.; Stampfer, Meir J.; Kenfield, Stacey A.

    2014-01-01

    Background Robot-assisted laparoscopic radical prostatectomy (RALP) has become increasingly common; however, there have been no nationwide, population-based, non–claims-based studies to evaluate differences in outcomes between RALP and open radical retropubic prostatectomy (RRP). Objective To determine surgical, oncologic, and health-related quality of life (HRQOL) outcomes following RALP and RRP in a nationwide cohort. Design, setting, and participants We identified 903 men in the Health Professionals Follow-up Study diagnosed with prostate cancer between 2000 and 2010 who underwent radical prostatectomy using RALP (n = 282) or RRP (n = 621) as primary treatment. Intervention Radical prostatectomy. Outcome measurements and statistical analysis We compared patients undergoing RALP or RRP across a range of perioperative, oncologic, and HRQOL outcomes. Results and limitations Use of RALP increased during the study period, constituting 85.2% of study subjects in 2009, up from 4.5% in 2003. Patients undergoing RALP compared to RRP were less likely to have a lymph node dissection (51.5% vs 85.4%; p < 0.0001), had less blood loss (207.4 ml vs 852.3 ml; p < 0.0001), were less likely to receive blood transfusions (4.3% vs 30.3%; p < 0.0001), and had shorter hospital stays (1.8 d vs 2.9 d; p < 0.0001). Surgical, oncologic, and HRQOL outcomes did not differ significantly among the groups. In multivariate logistic regression models, there were no significant differences in 3- or 5-yr recurrence-free survival comparing RALP versus RRP (hazard ratios: 0.98 [95% confidence interval (CI), 0.46–2.08] and 0.75 [95% CI, 0.18–3.11], respectively). Conclusions In a nationwide cohort of patients undergoing surgical treatment for prostate cancer, RALP was associated with shorter hospital stay, and lower blood loss and transfusion rates than RRP. Surgical oncologic and HRQOL outcomes were similar between groups. Patient summary We studied men throughout the United States with

  4. Operational results of the 13 kW/50 m sup 3 solar-driven cold store in Khartoum, The Sudan

    SciTech Connect

    Sloetjes, W.; Haverhals, J.; Kerkdijk, K. ); Ahmed, I.O.; Saber, H.; Eldin, S.S. ); Porsius, R.; Stolk, A. ); Karib, A.E.; Yousif, K. ); Hassan, H.W. )

    1988-01-01

    Experimental test results on a 13-kW solar-driven absorption refrigerator, located at Khartoum, The Sudan, are presented. Design considerations and cost aspects of the solar-driven refrigerator are given as well. The test shows that the solar-driven refrigerator performed satisfactorily during nine months of operation. However, continued tests have to show the ultimate system performance.

  5. 26 CFR 1.66-3 - Denial of the Federal income tax benefits resulting from the operation of community property law...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... resulting from the operation of community property law where spouse not notified. 1.66-3 Section 1.66-3 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED... 2002, the IRS audits both H and W. The Internal Revenue Service (IRS) may raise section 66(b) as to...

  6. Results of in-flight operation of scientific payload on micro-satellite “Kolibri-2000”

    NASA Astrophysics Data System (ADS)

    Klimov, Stanislav I.; Afanasyev, Yuri V.; Eismont, Natan A.; Grachev, Egor A.; Grigoryan, Oleg R.; Grushin, Valery A.; Lysakov, Dmitri S.; Nozdrachev, Mikhail N.

    2005-01-01

    The realization of Russian-Australian scientific—educational micro-satellite "Kolibri-2000" (weight of 20.5 kg, http://www.kolibri2000.ru 20 March, 2002), delivered into an orbit by "Progress M1-7", was the first item in the Program of Scientific—Educational Micro-Satellite (PSEMS' 2002-2007, http://iki.cosmos.ru/kollibri/mission1_e.htm) and designate the starting point of a series at perspective scientific—educational micro-satellites (SEMS, http://www.energia.ru/english/energia/sci-education/microsat/microsat-02.html). In the "Kolibri-2000" project, several schools equipped by School Center of Reception of the Information (SCRI), participated, including Russian schools (Obninsk http://ftschool.obninsk.org) and two Australian schools in Sydney, Knox Grammar School ( www.knox.nsw.edu.au) and Ravenswood School for Girls ( www.ravenswood.nsw.edu.au). The results of the "Kolibri-2000" first measurements on the orbit near the International Space Station will be submitted in this paper which include the ionosphere reaction during the April 2002 events, and address as understanding of the coupling and feedback in the Sun-Earth interaction.

  7. Estimation of the Risks of Collision or Strike to Freshwater Aquatic Organisms Resulting from Operation of Instream Hydrokinetic Turbines

    SciTech Connect

    Schweizer, Peter E; Cada, Glenn F; Bevelhimer, Mark S

    2010-05-01

    Hydrokinetic energy technologies have been proposed as renewable, environmentally preferable alternatives to fossil fuels for generation of electricity. Hydrokinetic technologies harness the energy of water in motion, either from waves, tides or from river currents. For energy capture from free-flowing rivers, arrays of rotating devices are most commonly proposed. The placement of hydrokinetic devices in large rivers is expected to increase the underwater structural complexity of river landscapes. Moore and Gregory (1988) found that structural complexity increased local fish populations because fish and other aquatic biota are attracted to structural complexity that provides microhabitats with steep flow velocity gradients (Liao 2007). However, hydrokinetic devices have mechanical parts, blades, wings or bars that move through the water column, posing a potential strike or collision risk to fish and other aquatic biota. Furthermore, in a setting with arrays of hydrokinetic turbines the cumulative effects of multiple encounters may increase the risk of strike. Submerged structures associated with a hydrokinetic (HK) project present a collision risk to aquatic organisms and diving birds (Cada et al. 2007). Collision is physical contact between a device or its pressure field and an organism that may result in an injury to that organism (Wilson et al. 2007). Collisions can occur between animals and fixed submerged structures, mooring equipment, horizontal or vertical axis turbine rotors, and structures that, by their individual design or in combination, may form traps. This report defines strike as a special case of collision where a moving part, such as a rotor blade of a HK turbine intercepts the path of an organism of interest, resulting in physical contact with the organism. The severity of a strike incidence may range from minor physical contact with no adverse effects to the organism to severe strike resulting in injury or death of the organism. Harmful effects

  8. Identification of human operator performance models utilizing time series analysis

    NASA Technical Reports Server (NTRS)

    Holden, F. M.; Shinners, S. M.

    1973-01-01

    The results of an effort performed by Sperry Systems Management Division for AMRL in applying time series analysis as a tool for modeling the human operator are presented. This technique is utilized for determining the variation of the human transfer function under various levels of stress. The human operator's model is determined based on actual input and output data from a tracking experiment.

  9. A Researcher's Dilemma: A Comparison of Estimated versus Actual College G.P.A.

    ERIC Educational Resources Information Center

    Herman, William E.; Nelson, Gena C.

    2009-01-01

    This study compared college student reported grade point averages (GPA) with actual GPA as recorded at the Registrar's Office to determine the accuracy of student reported GPA. Results indicated that, on average, students reported slightly higher GPA than their actual GPA. Additionally, females were virtually as accurate as males and students with…

  10. Evaluating Empathy in Interviewing: Comparing Self-Report with Actual Behavior.

    ERIC Educational Resources Information Center

    Tamburrino, Marijo B.; And Others

    1993-01-01

    A study compared medical students' self-assessments of patient interview behavior with external ratings of actual interviews. Focus was on behaviors reflecting empathy. Results suggest the self-report questionnaire is not an adequate measure of actual interviewing skills. (MSE)

  11. Correlates of Counselor Self-Actualization and Client-Perceived Facilitativeness

    ERIC Educational Resources Information Center

    Selfridge, Fred F.; Vander Kolk, Charles

    1976-01-01

    Client ratings of the abilities of 33 school counselors to communicate the core facilitative conditions of empathy, regard, congruence, and trust are compared to the counselors' scores on a measure of self-actualization. Results support the contention that there exists a strong relationship between self-actualization and counselor effectiveness as…

  12. Response to actual and simulated recordings of conventional takeoff and landing jet aircraft

    NASA Technical Reports Server (NTRS)

    Mabry, J. E.; Sullivan, B. M.

    1978-01-01

    Comparability between noise characteristics of synthesized recordings of aircraft in flight and actual recordings were investigated. Although the synthesized recordings were more smoothly time-varying than the actual recordings and the synthesizer could not produce a comb-filter effect that was present in the actual recordings, results supported the conclusion that annoyance response is comparable to the synthesized and actual recordings. A correction for duration markedly improved the validity of engineering calculation procedures designed to measure noise annoyance. Results led to the conclusion that the magnitude estimation psychophysical method was a highly reliable approach for evaluating engineering calculation procedures designed to measure noise annoyance. For repeated presentations of pairs of actual recordings, differences between judgment results for identical signals ranged from 0.0 to 0.5 db.

  13. Consequences of Predicted or Actual Asteroid Impacts

    NASA Astrophysics Data System (ADS)

    Chapman, C. R.

    2003-12-01

    Earth impact by an asteroid could have enormous physical and environmental consequences. Impactors larger than 2 km diameter could be so destructive as to threaten civilization. Since such events greatly exceed any other natural or man-made catastrophe, much extrapolation is necessary just to understand environmental implications (e.g. sudden global cooling, tsunami magnitude, toxic effects). Responses of vital elements of the ecosystem (e.g. agriculture) and of human society to such an impact are conjectural. For instance, response to the Blackout of 2003 was restrained, but response to 9/11 terrorism was arguably exaggerated and dysfunctional; would society be fragile or robust in the face of global catastrophe? Even small impacts, or predictions of impacts (accurate or faulty), could generate disproportionate responses, especially if news media reports are hyped or inaccurate or if responsible entities (e.g. military organizations in regions of conflict) are inadequately aware of the phenomenology of small impacts. Asteroid impact is the one geophysical hazard of high potential consequence with which we, fortunately, have essentially no historical experience. It is thus important that decision makers familiarize themselves with the hazard and that society (perhaps using a formal procedure, like a National Academy of Sciences study) evaluate the priority of addressing the hazard by (a) further telescopic searches for dangerous but still-undiscovered asteroids and (b) development of mitigation strategies (including deflection of an oncoming asteroid and on- Earth civil defense). I exemplify these issues by discussing several representative cases that span the range of parameters. Many of the specific physical consequences of impact involve effects like those of other geophysical disasters (flood, fire, earthquake, etc.), but the psychological and sociological aspects of predicted and actual impacts are distinctive. Standard economic cost/benefit analyses may not

  14. Time experiences, self-actualizing values, and creativity.

    PubMed

    Yonge, G D

    1975-12-01

    The Personal Orientation Inventory (POI), the Inventory of Temporal Experiences (ITE), and the Adjective Check List (ACL) were administered to 80 subjects. Sixteen scores were derived from the POI, 4 from the ITE and a Creativity score for the ACL. The resulting intercorrelations were interpreted in the light of the theories of Maslow and Hugenholtz which postulate a convergence of self-actualization, creativity, and certain experiences of time. The present study presents some evidence for the expected convergence and contributes to the construct validity of several of the variables studied. PMID:1202191

  15. Power Delivery from an Actual Thermoelectric Generation System

    NASA Astrophysics Data System (ADS)

    Kaibe, Hiromasa; Kajihara, Takeshi; Nagano, Kouji; Makino, Kazuya; Hachiuma, Hirokuni; Natsuume, Daisuke

    2014-06-01

    Similar to photovoltaic (PV) and fuel cells, thermoelectric generators (TEGs) supply direct-current (DC) power, essentially requiring DC/alternating current (AC) conversion for delivery as electricity into the grid network. Use of PVs is already well established through power conditioning systems (PCSs) that enable DC/AC conversion with maximum-power-point tracking, which enables commercial use by customers. From the economic, legal, and regulatory perspectives, a commercial PCS for PVs should also be available for TEGs, preferably as is or with just simple adjustment. Herein, we report use of a PV PCS with an actual TEG. The results are analyzed, and proper application for TEGs is proposed.

  16. Interferometric measurement of actual oblique astigmatism of ophthalmic lenses

    NASA Astrophysics Data System (ADS)

    Wihardjo, Erning

    1995-03-01

    A technique for measuring oblique astigmatism error of ophthalmic lenses is described. The technique is based on a Mach-Zehnder interferometer, which allows us to simulate the actual conditions of the eye. The effects of the lens power, the pupilary aperture size and the viewing distance in calculating a projected pupil zone on the lens are discussed. The projected pupil size on the lens affects the measurement result of the oblique astigmatism error. Conversion of the interferogram to astigmatism error in diopters is given.

  17. Application of fuzzy logic-neural network based reinforcement learning to proximity and docking operations: Special approach/docking testcase results

    NASA Technical Reports Server (NTRS)

    Jani, Yashvant

    1993-01-01

    As part of the RICIS project, the reinforcement learning techniques developed at Ames Research Center are being applied to proximity and docking operations using the Shuttle and Solar Maximum Mission (SMM) satellite simulation. In utilizing these fuzzy learning techniques, we use the Approximate Reasoning based Intelligent Control (ARIC) architecture, and so we use these two terms interchangeably to imply the same. This activity is carried out in the Software Technology Laboratory utilizing the Orbital Operations Simulator (OOS) and programming/testing support from other contractor personnel. This report is the final deliverable D4 in our milestones and project activity. It provides the test results for the special testcase of approach/docking scenario for the shuttle and SMM satellite. Based on our experience and analysis with the attitude and translational controllers, we have modified the basic configuration of the reinforcement learning algorithm in ARIC. The shuttle translational controller and its implementation in ARIC is described in our deliverable D3. In order to simulate the final approach and docking operations, we have set-up this special testcase as described in section 2. The ARIC performance results for these operations are discussed in section 3 and conclusions are provided in section 4 along with the summary for the project.

  18. Results Of Routine Strip Effluent Hold Tank And Decontaminated Salt Solution Hold Tank Samples From Modular Caustic-Side Solvent Extraction Unit During Macrobatch 5 Operations

    SciTech Connect

    Peters, T. B.; Fondeur, F. F.

    2013-04-30

    Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the ''microbatches'' of Integrated Salt Disposition Project (ISDP) Salt Batch (''Macrobatch'') 5 have been analyzed for {sup 238}Pu, {sup 90}Sr, {sup 137}Cs, and by Inductively Coupled Plasma Emission Spectroscopy (ICPES). The results indicate good decontamination performance within process design expectations. While the data set is sparse, the results of this set and the previous set of results for Macrobatch 4 samples indicate generally consistent operations. The DSSHT samples show continued presence of titanium, likely from leaching of the monosodium titanate in the Actinide Removal process (ARP).

  19. Evaluation of potential severe accidents during low power and shutdown operations at Grand Gulf, Unit 1: Summary of results. Volume 1

    SciTech Connect

    Whitehead, D.W.; Staple, B.D.; Daniel, S.L.

    1995-07-01

    During 1989 the Nuclear Regulatory Commission (NRC) initiated an extensive program to examine the potential risks during low power and shutdown operations. Two plants, Surry and Grand Gulf, were selected as the plants to be studied by Brookhaven National Laboratory (Surry) and Sandia National Laboratories (Grand Gulf). This report documents the work performed during the analysis of the Grand Gulf plant. A phased approach was used for the overall study. In Phase 1, the objectives were to identify potential vulnerable plant configurations, to characterize (on a high, medium, or low basis) the potential core damage accident scenario frequencies and risks, and to provide a foundation for a detailed Phase 2 analysis. It was in Phase 1 that the concept of plant operational states (POSs) was developed to allow the analysts to better represent the plant as it transitions from power operation to nonpower operation than was possible with the traditional technical specification divisions of modes of operation. This phase consisted of a coarse screening analysis performed for all POSs, including seismic and internal fire and flood for some POSs. In Phase 2, POS 5 (approximately cold shutdown as defined by Grand Gulf Technical Specifications) during a refueling outage was selected as the plant configuration to be analyzed based on the results of the Phase 1 study. The scope of the Level 1 study includes plant damage state analysis and uncertainty analysis and is documented in a multi-volume NUREG/CR report (i.e., NUREG/CR-6143). The internal events analysis is documented in Volume 2. Internal fire and internal flood analyses are documented in Volumes 3 and 4, respectively. A separate study on seismic analysis, documented in Volume 5, was performed for the NRC by Future Resources Associates, Inc. The Level 2/3 study of the traditional internal events is documented in Volume 6, and a summary of the results for all analyses is documented in Volume 1.

  20. A model-based approach to adjust microwave observations for operational applications: results of a campaign at Munich Airport in winter 2011/2012

    NASA Astrophysics Data System (ADS)

    Güldner, J.

    2013-10-01

    In the frame of the project "LuFo iPort VIS" which focuses on the implementation of a site-specific visibility forecast, a field campaign was organised to offer detailed information to a numerical fog model. As part of additional observing activities, a 22-channel microwave radiometer profiler (MWRP) was operating at the Munich Airport site in Germany from October 2011 to February 2012 in order to provide vertical temperature and humidity profiles as well as cloud liquid water information. Independently from the model-related aims of the campaign, the MWRP observations were used to study their capabilities to work in operational meteorological networks. Over the past decade a growing quantity of MWRP has been introduced and a user community (MWRnet) was established to encourage activities directed at the set up of an operational network. On that account, the comparability of observations from different network sites plays a fundamental role for any applications in climatology and numerical weather forecast. In practice, however, systematic temperature and humidity differences (bias) between MWRP retrievals and co-located radiosonde profiles were observed and reported by several authors. This bias can be caused by instrumental offsets and by the absorption model used in the retrieval algorithms as well as by applying a non-representative training data set. At the Lindenberg observatory, besides a neural network provided by the manufacturer, a measurement-based regression method was developed to reduce the bias. These regression operators are calculated on the basis of coincident radiosonde observations and MWRP brightness temperature (TB) measurements. However, MWRP applications in a network require comparable results at just any site, even if no radiosondes are available. The motivation of this work is directed to a verification of the suitability of the operational local forecast model COSMO-EU of the Deutscher Wetterdienst (DWD) for the calculation of model

  1. Intra-operative ultrasound hand-held strain imaging for the visualization of ablations produced in the liver with a toroidal HIFU transducer: first in vivo results

    PubMed Central

    Chenot, Jérémy; Melodelima, David; N'Djin, William Apoutou; Souchon, Rémi; Rivoire, Michel; Chapelon, Jean-Yves

    2010-01-01

    The use of hand-held ultrasound strain imaging for intra-operative real-time visualization of HIFU ablations produced in the liver by a toroidal transducer was investigated. A linear 12 MHz ultrasound imaging probe was used to obtain radiofrequency signals. Using a fast cross-correlation algorithm, strain images were calculated and displayed at 60 frames/s, allowing the use of hand-held strain imaging intra-operatively. Fourteen HIFU lesions were produced in 4 pigs. Intra-operative strain imaging of HIFU ablations in the liver was feasible owing to the high frame rate. The correlation between dimensions measured on gross pathology and dimensions measured on B-mode images and on strain images were R = 0.72 and R = 0.94 respectively. The contrast between ablated and non-ablated tissue was significantly higher (p<0.05) in the strain images (22 dB) than in the B-mode images (9 dB). Strain images allowed equivalent or improved definition of ablated regions when compared with B-mode images. Real-time intra-operative hand-held strain imaging seems to be a promising complement to conventional B-Mode imaging for the guidance of HIFU ablations produced in the liver during an open procedure. These results support that hand-held strain imaging outperforms conventional B-mode ultrasound and could potentially be used for assessment of thermal therapies. PMID:20479514

  2. Moving-bed gasification - combined-cycle control study. Volume 1: results and conclusions, Case 1 - air-blown dry-ash operation. Final report

    SciTech Connect

    Ahner, D.J.; Brower, A.S.; Dawes, M.H.; Patel, A.S.

    1981-03-01

    A simulation study has been conducted to investigate the inherent process dynamics and required control strategies for an integrated coal gasification/combined cycle (GCC) power plant to operate successfully under load-changing conditions to meet power system requirements. The simulated GCC plant configuration is similar to the flowsheet developed in earlier EPRI economic studies (RP239), based on an air-blown, dry-ash, moving-bed gasifier of the Lurgi-type. A following GCC plant control study will be based on a Lurgi-type gasifier modified for oxygen-blown, slagging operations such as that being developed by British Gas Corporation. A large ditial computer simulation model of the GCC plant operating on a large utility power system network was developed to examine alternate plant control strategies. Gas turbine-lead and gasifier-lead control modes were evaluated with respect to power system requirements for daily load following, tie-line flow regulation with thermal backup, and frequency regulation. Inherent features of the gasifier led to unique process dynamics for the GCC plant. Sizeable transients were observed during load-changing operations, both in the fuel process and the steam system. However, the plant compensated effectively for such transients with a modified gas turbine-lead control strategy, by making use of fast-responding gas turbine controls and the large inherent volume of the fuel process. The results verify the capability of the GCC plant to operate with the fuel process closely integrated with the combined cycle plant under rapidly changing conditions. Furthermore, a GCC plant control strategy was developed which can successfully meet power sytem requirements within fuel system limitations, allowing an overall plant response rate of four (4) percent per minute.

  3. Operation of lumbar zygoapophyseal joint cysts using a full-endoscopic interlaminar and transforaminal approach: prospective 2-year results of 74 patients.

    PubMed

    Komp, Martin; Hahn, Patrick; Ozdemir, Semih; Merk, Harry; Kasch, Richard; Godolias, Georgios; Ruetten, Sebastian

    2014-12-01

    In appropriate situations, extensive decompression with laminectomy often continues to be described as the method of choice for operations involving lumbar zygoapophyseal joint (z-joint) cysts. Tissue-sparing procedures are nevertheless becoming more common. Endoscopic techniques have become the standard procedures in many areas because of the advantages they offer in terms of surgical technique and in rehabilitation. One key aspect in spinal surgery was the development of instruments for sufficient bone resection carried out under continuous visual control. This enabled endoscopes to be used when operating on z-joint cysts. The objective of this prospective study was to examine the technical possibilities for the full-endoscopic interlaminar and transforaminal technique in lumbar z-joint cysts. A total of 74 patients were followed up for 2 years. The results show that 85% of the patients no longer have any leg pain or that the pain had been almost completely eliminated, and 11 % experience occasional pain. The complication rate was low. The full-endoscopic techniques brought advantages in the following areas: operation, complications, traumatization, and rehabilitation. The recorded results show that full-endoscopic resection of a z-joint cyst using an interlaminar and transforaminal approach provides an adequate and safe supplement, and is an alternative to conventional procedures when the indication criteria are fulfilled. It also offers the advantages of a minimally invasive intervention. PMID:24667524

  4. Operational results of a low NO{sub x} burner retrofit on a 780 net MW{sub e} PC-fired utility boiler

    SciTech Connect

    Bryk, S.A.; Cioffi, P.L.; Tucker, T.J.; Mellody, J.G.; Hooks, M.E.

    1995-12-31

    The primary objective of this project was to comply with state and federal clean air regulations while maintaining operational flexibility and control. This objective was accomplished with the installation of DRB-XCL{reg_sign} burners with a separated overfire air system. The DRB-XCL{reg_sign} burners can consistently achieve 0.5 lbs/10{sup 6} Btu NO{sub x} or less. Even lower NO{sub x} levels can be achieved with the new equipment. However, increased carbon levels affecting stack opacity prevent long-term operation at this level with the existing scrubbing equipment. Final test results indicated that the project goals were met with some exceeded. The results of this project pointed out the numerous interactions of all of the interrelated complex systems in today`s state-of-the-art power plants. The increase in unburned carbon levels affected the wet scrubber and impacted stack plume color. Being one indicator of inefficiency, this item is currently being reviewed to take advantage of further improving operating efficiency. Mechanical reliability of the Babcock & Wilcox DRB-XCL{reg_sign} burner has been good and it is estimated that long-term maintenance costs will be low. Close cooperation between Ohio Edison and B&W contributed positively to the success of this project.

  5. Results evaluation of the use of intra‐articular sodium hyaluronate in the post‐operative knee arthroscopy☆☆☆

    PubMed Central

    de Paula Pereira Junior, Ayrton; Fasolin, Ricardo Pozzi; Sossa, Felipe Ayusso Correa; de Almeida Lira Neto, Ozorio; Navarro, Marcelo Schmidt; Milani, Antonio

    2014-01-01

    Objective to evaluate the efficacy of hyaluronic acid in the post‐operative of knee arthroscopy. Methods we have evaluated 49 patients undergoing arthroscopic procedure with the use of intra‐articular hyaluronic acid (Group 1) and 49 patients undergoing arthroscopic procedure without the use of hyaluronic acid (Group 2). Patients were evaluated based on the Visual Analogue Scale, household analgesia, assessment of the Range of Motion with a goniometer, and the Lysholm questionnaire. Results there were no substantial adverse effects on either group. Conclusion the use of hyaluronic acid in the post‐operative of knee arthroscopy is justified due/because it leads to a decrease in pain in the early stage, enabling faster recovery of the patient. PMID:26229770

  6. An end-to-end approach to the EUCLID NISP on-board pre-processing operations: tests and latest results

    NASA Astrophysics Data System (ADS)

    Bonoli, Carlotta; Bortoletto, Favio; D'Alessandro, Maurizio; Corcione, Leonardo; Ligori, Sebastiano; Nicastro, Luciano; Trifoglio, Massimo; Valenziano, Luca; Zerbi, Filippo M.; Crouzet, Pierre-Elie; Jung, Andreas

    2012-09-01

    NISP is the near IR spectrophotometer instrument part of the Cosmic Vision Euclid mission. In this paper we describe an end-to-end simulation scheme developed in the framework of the NISP design study to cover the expected focal-plane on-board pre-processing operations. Non-destructive detector readouts are simulated for a number of different readout strategies, taking into account scientific and calibration observations; resulting frames are passed through a series of steps emulating the foreseen on-board pipeline, then compressed to give the final result. In order to verify final frame quality and resulting computational and memory load, we tested this architecture on a number of hardware platforms similar to those possible for the final NISP computing unit. Here we give the results of the latest tests. This paper mainly reports the technical status at the end of the Definition Phase and it is presented on behalf of the Euclid Consortium.

  7. 40 CFR 63.5335 - How do I determine the actual HAP loss?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... process operation type. (2) Chemical Inventory Mass Balance. Determine the actual monthly HAP loss from... month, and business purchasing records to indicate additions to the inventory of chemical supplies. The... chemical inventory from the beginning of the month chemical inventory and adding the quantities of...

  8. 40 CFR 63.5335 - How do I determine the actual HAP loss?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... operation type. (2) Chemical Inventory Mass Balance. Determine the actual monthly HAP loss from your..., and business purchasing records to indicate additions to the inventory of chemical supplies. The net... chemical inventory from the beginning of the month chemical inventory and adding the quantities of...

  9. California Charter Oversight: Key Elements and Actual Costs. CRB 12-001

    ERIC Educational Resources Information Center

    Blanton, Rebecca E.

    2012-01-01

    This study was mandated by SB537 (Simitian, Chapter 650, Stats. of 2007, codified at Ed. Code Section 47613), which requires the California Research Bureau (CRB) to prepare and submit to the Legislature a report on the key elements and actual costs of charter school oversight. Charter schools are public schools that are operated by entities other…

  10. 40 CFR 63.5335 - How do I determine the actual HAP loss?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... process operation type. (2) Chemical Inventory Mass Balance. Determine the actual monthly HAP loss from... month, and business purchasing records to indicate additions to the inventory of chemical supplies. The... chemical inventory from the beginning of the month chemical inventory and adding the quantities of...

  11. The Conceptual Evolution of Actual Mathematical Infinity.

    ERIC Educational Resources Information Center

    Moreno A., Luis E.; Waldegg, Guillermina

    1991-01-01

    Analyzed are the different stages in the conceptual evolution of infinity as developed historically through the work of Bolzano and Cantor. Results of a study of 18 to 20 year old's concept of infinity prior to instruction produced aspects of the passage between conceptual levels of infinity. (MDH)

  12. What Writing Represents What Scientists Actually Do?

    ERIC Educational Resources Information Center

    Robertson, Bill

    2005-01-01

    Often the writing that students in elementary school do in connection with science is their final report of a science fair project. They diligently file a report in the form of the scientific method--introduction, hypothesis, materials, procedure, results, and conclusion. This form of science writing persists through college courses in science,…

  13. Compact group actions on C*-algebras: classification, non-classifiability, and crossed products and rigidity results for Lp-operator algebras

    NASA Astrophysics Data System (ADS)

    Gardella, Emilio Eusebio

    This dissertation is concerned with representations of locally compact groups on different classes of Banach spaces. The first part of this work considers representations of compact groups by automorphisms of C*-algebras, also known as group actions on C*-algebras. The actions we study enjoy a freeness-type of property, namely finite Rokhlin dimension. We investigate the structure of their crossed products, mainly in relation to their classifiability, and compare the notion of finite Rokhlin dimension with other existing notions of noncommutative freeness. In the case of Rokhlin dimension zero, also known as the Rokhlin property, we prove a number of classification theorems for these actions. Also, in this case, much more can be said about the structure of the crossed products. In the last chapter of this part, we explore the extent to which actions with Rokhlin dimension one can be classified. Our results show that even for Z2-actions on O2, their classification is not Borel, and hence it is intractable. The second part of the present dissertation focuses on isometric representations of groups on Lp-spaces. For p=2, these are the unitary representations on Hilbert spaces. We study the Lp-analogs of the full and reduced group C*-algebras, particularly in connection to their rigidity. One of the main results of this work asserts that for p different from 2, the isometric isomorphism type of the reduced group L p-operator algebra recovers the group. Our study of group algebras acting on Lp-spaces has also led us to answer a 20-year-old question of Le Merdy and Junge: for p different from 2, the class of Banach algebras that can be represented on an Lp-space is not closed under quotients. We moreover study representations of groupoids, which are a generalization of groups where multiplication is not always defined. The algebras associated to these objects provide new examples of Lp-operator algebras and recover some previously existing ones. Groupoid L p-operator

  14. Radiation Monitoring Results from the First Year of Operation of a Unique Ambulance-based Computed Tomography Unit for the Improved Diagnosis and Treatment of Stroke Patients.

    PubMed

    Gutiérrez, Janet M; Emery, Robert J; Parker, Stephanie A; Jackson, Kamilah; Grotta, James C

    2016-05-01

    When a blood clot blocks the blood supply to the brain or when a blood vessel bursts, resulting in brain cell death, the medical condition is referred to as a "stroke." Stroke is a main cause of death worldwide and is a common cause of disability. A common form of stroke, called ischemic stroke, is when blood flow to the brain is decreased. Clinical research has revealed that treatment within the very first hours of symptom onset is key for ischemic stroke with recanalization of occluded arteries by thrombolysis with alteplase. Computed tomography (CT) is one of the diagnostic tools used to determine if this treatment path is appropriate. To determine if health outcomes of possible stroke patients can be improved by decreasing the time from symptom presentation to treatment, the first mobile stroke ambulance unit in the United States was deployed by The University of Texas Health Science Center at Houston (UTHealth) in 2014, equipped with a computed tomography imaging system. The mobile stroke unit shortens the time to treatment for stroke patients by allowing pre-hospital treatment. Having completed its first year of operation, radiation-monitoring data describing the doses delivered to various entities have been characterized. The CT operator's cumulative deep dose equivalent for 1 y of operation was 1.14 mSv resulting from the care of 106 patients. Area monitors were deployed and measurements performed demonstrating that general public doses did not exceed 0.02 mSv h or 1.0 mSv year. PMID:27023154

  15. METHODS AND RESULTS OF RECONSTRUCTION OF NOBLE GAS RELEASES FROM THE STACKS OF THE MAYAK PA GRAPHITE REACTORS OVER THE WHOLE PERIOD OF THEIR OPERATION

    SciTech Connect

    Glagolenko, Y. V.; Drozhko, Evgeniy G.; Mokrov, Y.; Pyatin, N. P.; Rovny, Sergey I.; Anspaugh, L. R.; Napier, Bruce A.

    2008-06-01

    Brief analysis of design features and operational modes of Mayak PA industrial graphite-uranium reactors (PUGRs) is given. The above mentioned Mayak PA PUGRs determined the rates of releases of radioactive noble gases (RNG) from activation (41Ar) and fission (isotopes of Krypton and Xenon) through the vent stack of the reactor. Information is given on methods and results of experimental determination of RNG atmospheric releases for the period starting from 1965 till PUGRs decommissioning in 1987-1990. A calculation method for reconstruction of radioactive noble gas releases is proposed and justified. The results of reconstruction are given. It is shown that maximum rates of RNG releases from PUGRs high stacks were observed in the 1950s, when ordinary atmospheric air was used as a cover gas for the reactor graphite stacks and gas purification systems (flow-type gas holders) had not been installed yet.

  16. Neuromuscular adaptation to actual and simulated weightlessness

    NASA Technical Reports Server (NTRS)

    Edgerton, V. R.; Roy, R. R.

    1994-01-01

    The chronic "unloading" of the neuromuscular system during spaceflight has detrimental functional and morphological effects. Changes in the metabolic and mechanical properties of the musculature can be attributed largely to the loss of muscle protein and the alteration in the relative proportion of the proteins in skeletal muscle, particularly in the muscles that have an antigravity function under normal loading conditions. These adaptations could result in decrements in the performance of routine or specialized motor tasks, both of which may be critical for survival in an altered gravitational field, i.e., during spaceflight and during return to 1 G. For example, the loss in extensor muscle mass requires a higher percentage of recruitment of the motor pools for any specific motor task. Thus, a faster rate of fatigue will occur in the activated muscles. These consequences emphasize the importance of developing techniques for minimizing muscle loss during spaceflight, at least in preparation for the return to 1 G after spaceflight. New insights into the complexity and the interactive elements that contribute to the neuromuscular adaptations to space have been gained from studies of the role of exercise and/or growth factors as countermeasures of atrophy. The present chapter illustrates the inevitable interactive effects of neural and muscular systems in adapting to space. It also describes the considerable progress that has been made toward the goal of minimizing the functional impact of the stimuli that induce the neuromuscular adaptations to space.

  17. The hotelling principle and in-ground values of oil reserves: Why the principle over-predicts actual values

    SciTech Connect

    McDonald, S.L.

    1994-12-31

    Two articles previously published in this Journal reported that the valuation version of the Hotelling Principle over-predicts in-ground values of oil and gas reserves by a factor of approximately two. This paper shows these results are to be expected once it is understood that: (1) the Principle assumes individual operators have the effective freedom to schedule extraction rates so as to make net prices rise at the rate of discount, regardless of the course of gross (wellhead) prices; and (2) the long-prevailing system of regulating oil well spacing and extraction rates in the United States and Canada, designed to deal with the common pool problem, effectively denies operators that freedom. The discrepancy between actual in-ground values and those predicted by the Hotelling Principle suggests the benefits to be had by substituting compulsory reservoir unitization cum manager freedom for the current system of regulation.10 refs., 1 tab., 1 fig.

  18. Actual Versus Predicted Cardiovascular Demands in Submaximal Cycle Ergometer Testing

    PubMed Central

    HOEHN, AMANDA M.; MULLENBACH, MEGAN J.; FOUNTAINE, CHARLES J.

    2015-01-01

    The Astrand-Rhyming cycle ergometer test (ARCET) is a commonly administered submaximal test for estimating aerobic capacity. Whereas typically utilized in clinical populations, the validity of the ARCET to predict VO2max in a non-clinical population, especially female, is less clear. Therefore, the purpose of this study was to determine the accuracy of the ARCET in a sample of healthy and physically active college students. Subjects (13 females, 10 males) performed a maximal cycle ergometer test to volitional exhaustion to determine VO2max. At least 48 hours later, subjects performed the ARCET protocol. Predicted VO2max was calculated following the ARCET format using the age corrected factor. There was no significant difference (p=.045) between actual (41.0±7.97 ml/kg/min) and predicted VO2max (40.3±7.58 ml/kg/min). When split for gender there was a significant difference between actual and predicted VO2 for males, (45.1±7.74 vs. 42.7±8.26 ml/kg/min, p=0.029) but no significant difference observed for females, (37.9±6.9 vs. 38.5±6.77 ml/kg/min, p=0.675). The correlation between actual and predicted VO2 was r=0.84, p<0.001 with an SEE= 4.3 ml/kg/min. When split for gender, the correlation for males was r=0.94, p<0.001, SEE=2.72 ml/kg/min; for females, r=0.74, p=0.004, SEE=4.67 ml/kg/min. The results of this study indicate that the ARCET accurately estimated VO2max in a healthy college population of both male and female subjects. Implications of this study suggest the ARCET can be used to assess aerobic capacity in both fitness and clinical settings where measurement via open-circuit spirometry is either unavailable or impractical. PMID:27182410

  19. Gauging triple stores with actual biological data

    PubMed Central

    2012-01-01

    Background Semantic Web technologies have been developed to overcome the limitations of the current Web and conventional data integration solutions. The Semantic Web is expected to link all the data present on the Internet instead of linking just documents. One of the foundations of the Semantic Web technologies is the knowledge representation language Resource Description Framework (RDF). Knowledge expressed in RDF is typically stored in so-called triple stores (also known as RDF stores), from which it can be retrieved with SPARQL, a language designed for querying RDF-based models. The Semantic Web technologies should allow federated queries over multiple triple stores. In this paper we compare the efficiency of a set of biologically relevant queries as applied to a number of different triple store implementations. Results Previously we developed a library of queries to guide the use of our knowledge base Cell Cycle Ontology implemented as a triple store. We have now compared the performance of these queries on five non-commercial triple stores: OpenLink Virtuoso (Open-Source Edition), Jena SDB, Jena TDB, SwiftOWLIM and 4Store. We examined three performance aspects: the data uploading time, the query execution time and the scalability. The queries we had chosen addressed diverse ontological or biological questions, and we found that individual store performance was quite query-specific. We identified three groups of queries displaying similar behaviour across the different stores: 1) relatively short response time queries, 2) moderate response time queries and 3) relatively long response time queries. SwiftOWLIM proved to be a winner in the first group, 4Store in the second one and Virtuoso in the third one. Conclusions Our analysis showed that some queries behaved idiosyncratically, in a triple store specific manner, mainly with SwiftOWLIM and 4Store. Virtuoso, as expected, displayed a very balanced performance - its load time and its response time for all the

  20. Isolating the actual signal of paleointensity?

    NASA Astrophysics Data System (ADS)

    Valet, J. M.; Moreno, E.; Bassinot, F.; Herrero-Bervera, E.

    2011-12-01

    Signals of relative and absolute paleointensity suffer inaccuracies and contaminations that must be considered to improve our knowledge of the field variations. Climatically related changes in rock magnetic parameters are frequently suspected of influencing the signal of relative paleointensity extrated from marine sediments. High resolution measurements of climatic and magnetic parameters have been performed on two cores from the eastern China Sea and the western Caroline Basin. On both cores, magnetic parameters show a strong imprint of climatic changes but the absence of relationship between the inclination and the bulk density indicates that the directional changes do not depend on lithology. All normalization parameters yielded similar estimates of relative paleointensity (RPI), but we have noticed the persistence of climatic components in the signal. Principal Component Analysis (PCA) applied to different parameters related to climate, lithology and paleointensity has allowed to extract a "clean" magnetic signal that we refer as "principal component of paleointensity (PCP)" which is in better agreement with the Sint-2000 composite curve and provides a reliable record of relative paleointensity. The presence of climatic frequencies in RPIs most likely reflects the influence of lithology on the response of magnetization to field intensity. We suggest that PCA analysis can be very useful to approach these problems. Not only can the calculation separate overlapping climatic and magnetic signals, but it indicates what confidence should be given to the data. Incidentally, the present results emphasize the importance of carrying out detailed paleoclimatic analyses along with paleointensity studies. Many approaches have been proposed during the past 20 years for experiments of absolute paleointensity in order to reduce the duration of the experiments and increase the number of field determinations. However, this is frequently obtained to the detriment of the accuracy

  1. The use of macrophyte-based systems for phosphorus removal: an overview of 25 years of research and operational results in Florida.

    PubMed

    DeBusk, T A; Dierber, F E; Reddy, K R

    2001-01-01

    Phosphorus (P) removal from wastewaters and surface runoff using macrophyte-based systems (MBS) has been a topic of great interest in Florida for over 25 years. During this period, P removal by both treatment wetlands and floating aquatic macrophyte systems has been evaluated from both a research and operational standpoint. Several factors have contributed to the increased focus on the use of MBS for P removal. First, there exist no conventional technologies that can cost-effectively achieve the low outflow P concentrations required to protect the integrity of Florida's relatively pristine surface waters. Second, because MBSs typically provide some water storage, they can accommodate the wide ranges of flows typical for runoff sources such as agricultural drainage waters. Finally, many regions in Florida have sufficient area for deployment of the relatively land-intensive MBS technologies. The first P removal work in Florida was initiated in the mid-1970s, and involved pilot-scale research on domestic wastewater treatment by natural wetlands. Parallel studies were performed with managed (periodically harvested) floating plant systems (i.e., Eichhornia crassipes) for tertiary treatment. Since that time, the range of operational systems that have been deployed include emergent macrophyte-based and forested wetlands, managed floating plant systems, and submerged macrophyte-based systems. Waters treated by MBS include domestic effluents, agricultural runoff and eutrophic lake waters. Phosphorus removal targets for MBS in Florida have been as low as 10 microg/L. In this paper, we summarize research and operational results for MBS in Florida over the past 25 years. PMID:11804124

  2. Prospective controlled vagotomy trial for duodenal ulcer: primary results, sequelae, acid secretion, and recurrence rates two to five years after operation.

    PubMed Central

    Christiansen, J; Jensen, H E; Ejby-Poulsen, P; Bardram, L; Henriksen, F W

    1981-01-01

    In a prospective, controlled clinical trial, vagotomies for duodenal, pyloric, and prepyloric ulcers were performed on 259 patients. Eighty-three patients were randomly selected for truncal vagotomy and drainage (TV + D), 93 patients were randomly selected for selective gastric vagotomy and drainage (SV + D) and 83 patients were randomly selected for parietal cell vagotomy without drainage (PCV). This interim report deals with the primary results, reduction in acid secretion, sequelae, and recurrence rates two to five years after the operation. One patient died after the operation. Postoperative complications were evenly distributed between the three operations. No differences in spontaneous acid secretion (BAO), peak acid output after pentagastrin stimulation (PAOP), or peak acid output after insulin stimulation (PAOI) were found. Patients with recurrent ulcers ahd smaller reductions in BAO than patients without ulcer recurrences, although not significantly. Patients with ulcer recurrences after TV + D had, in contrast to ulcer recurrences after SV + D and PCV, a significantly smaller reduction in PAOP than patients without recurrences. The overall recurrence rate was 13%: 10% after TV + D, 14% after SV + D and 16% after PCV. The risk of ulcer recurrence within the first three years, calculated by an actuarial method, was found to be significantly higher after PCV (0.52% per month) than after TV + D (0.32% per month), but not different from SV + D (0.42% per month). In contrast to TV + D and SV + D, no recurrences after PCV occurred after three years--25% of the patients were followed for five years. It is concluded that the trial, at present, does not point to any evident superiority of PCV. PMID:7006528

  3. 26 CFR 1.953-2 - Actual United States risks.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ..., and water damage risks incurred when property is actually located in the United States and marine... 26 Internal Revenue 10 2014-04-01 2013-04-01 true Actual United States risks. 1.953-2 Section 1... coverage as “.825% plus .3% fire, etc. risks plus .12% water risks = 1.245%”, a reasonable basis exists...

  4. Self-actualization: Its Use and Misuse in Teacher Education.

    ERIC Educational Resources Information Center

    Ivie, Stanley D.

    1982-01-01

    The writings of Abraham Maslow are analyzed to determine the meaning of the psychological term "self-actualization." After pointing out that self-actualization is a rare quality and that it has little to do with formal education, the author concludes that the concept has little practical relevance for teacher education. (PP)

  5. The Self-Actualization of Polk Community College Students.

    ERIC Educational Resources Information Center

    Pearsall, Howard E.; Thompson, Paul V., Jr.

    This article investigates the concept of self-actualization introduced by Abraham Maslow (1954). A summary of Maslow's Needs Hierarchy, along with a description of the characteristics of the self-actualized person, is presented. An analysis of humanistic education reveals it has much to offer as a means of promoting the principles of…

  6. From Self-Awareness to Self-Actualization

    ERIC Educational Resources Information Center

    Cangemi, Joseph P.; Englander, Meryl R.

    1974-01-01

    Highest priority of education is to help students utilize as much of their talent as is possible. Third Force psychologists would interpret this as becoming self-actualized. Self-awareness is required for psychological growth. Without self-awareness there can be no growth, no mental hygiene, and no self-actualization. (Author)

  7. 12 CFR 1806.203 - Selection Process, actual award amounts.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Selection Process, actual award amounts. 1806... OF THE TREASURY BANK ENTERPRISE AWARD PROGRAM Awards § 1806.203 Selection Process, actual award... round: (1) To select Applicants not previously selected, using the calculation and selection...

  8. Self-Actualization and the Effective Social Studies Teacher.

    ERIC Educational Resources Information Center

    Farmer, Rodney B.

    1980-01-01

    Discusses a study undertaken to investigate the relationship between social studies teachers' degrees of self-actualization and their teacher effectiveness. Investigates validity of using Maslow's theory of self-actualization as a way of identifying the effective social studies teacher personality. (Author/DB)

  9. Gebrauchstexte im Fremdsprachenunterricht ("Actual" Texts in Foreign Language Teaching)

    ERIC Educational Resources Information Center

    Ziegesar, Detlef von

    1976-01-01

    Presents for analysis actual texts and texts specially written for teaching, arriving at a basis for a typology of actual texts. Defines teaching aims using such texts, and develops, from a TV program, a teaching unit used in a Karlsruhe school. (Text is in German.) (IFS/WGA)

  10. Self-Actualizing Men and Women: A Comparison Study.

    ERIC Educational Resources Information Center

    Hall, Eleanor G.; Hansen, Jan B.

    1997-01-01

    The self-actualization of 167 women who lived in the Martha Cook (MC) dormitory of the University of Michigan (1950-1970) was compared to that of a group of Ivy League men researched in another study. In addition, two groups of MC women were compared to each other to identify differences which might explain why some self-actualized while other did…

  11. SELF-ACTUALIZATION AND THE UTILIZATION OF TALENT.

    ERIC Educational Resources Information Center

    FRENCH, JOHN R.P.; MILLER, DANIEL R.

    THIS STUDY ATTEMPTED (1) TO DEVELOP A THEORY OF THE CAUSES AND CONSEQUENCES OF SELF-ACTUALIZATION AS RELATED TO THE UTILIZATION OF TALENT, (2) TO FIT THE THEORY TO EXISTING DATA, AND (3) TO PLAN ONE OR MORE RESEARCH PROJECTS TO TEST THE THEORY. TWO ARTICLES ON IDENTITY AND MOTIVATION AND SELF-ACTUALIZATION AND SELF-IDENTITY THEORY REPORTED THE…

  12. 26 CFR 1.962-3 - Treatment of actual distributions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 26 Internal Revenue 10 2013-04-01 2013-04-01 false Treatment of actual distributions. 1.962-3... TAX (CONTINUED) INCOME TAXES (CONTINUED) Controlled Foreign Corporations § 1.962-3 Treatment of actual... a foreign corporation. (ii) Treatment of section 962 earnings and profits under § 1.959-3....

  13. School Guidance Counselors' Perceptions of Actual and Preferred Job Duties

    ERIC Educational Resources Information Center

    Edwards, John Dexter

    2010-01-01

    The purpose of this study was to provide process data for school counselors, administrators, and the public, regarding school counselors' actual roles within the guidance counselor preferred job duties and actual job duties. In addition, factors including National Certification or no National Certification, years of counseling experience, and…

  14. [The information of the schizophrenic patient: actuality].

    PubMed

    Palazzolo, J; Brousse, G; Favre, P; Llorca, P-M

    2005-01-01

    forward to her visits. Case managers help negotiate compliance to medication, housing, meaningful activity, substance abuse, poverty, isolation, and everything else living in the community can throw at you. Without a spouse you tend to spend a lot of time alone. One of the main reasons Marie-Claude and I moved in with each other was that neither of us was enjoying living alone. It was very romantic at first but now we are just friends who see less and less of each other. I suspect schizophrenia interferes with the quality and depth of relationships you have with other people. Amongst the people I know, schizophrenia has meant a pretty solitary life of poverty. I have a lot of acquaintances, and colleagues, but few close friends when not at work. Over the last ten years of living with schizophrenia on medication it is celibacy that has hurt the most. It saps the life out of you, your self confidence, your self esteem. In some Scandinavian countries and Holland disabled people are allowed monthly visits by state approved sex workers. To me that is only common sense. To live without sex is unnatural and can only cause emotional suffering. We don't recognize the importance of quality sexual experience in keeping people healthy and happy in France. That doesn't mean it isn't I have a pretty high profile in my community through the meaningful activity I do. From having a half dozen names and faces to remember, I now have what seems like hundreds. I have a lot of trouble remembering people's names and faces. I am still meeting new people but I'm rarely invited to socialize with any after work. They have families, full time jobs, kids, cars, cottages, etc. My life at home is pretty solitary. It's a nuisance to travel across the city to visit people. There are few people that I share a similar background with. Since people with schizophrenia tend to have trouble learning new things, and change very little as a result, we tend to have trouble making new friends. People with

  15. RESULTS OF ROUTINE STRIP EFFLUENT HOLD TANK AND DECONTAMINATED SALT SOLUTION HOLD TANK SAMPLES FROM MODULAR CAUSTIC-SIDE SOLVENT EXTRACTION UNIT DURING MACROBATCH 3 OPERATIONS

    SciTech Connect

    Peters, T.; Fink, S.

    2011-06-10

    Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the 'microbatches' of Integrated Salt Disposition Project (ISDP) Salt Batch ('Macrobatch') 3 have been analyzed for {sup 238}Pu, {sup 90}Sr, {sup 137}Cs, and by Inductively Coupled Plasma Emission Spectroscopy (ICPES). The results indicate good decontamination performance within process design expectations. While the data set is sparse, the results of this set and the previous set of results for Macrobatch 3 samples indicate consistent operations. However, the Decontamination Factors for plutonium and strontium removal have declined in Macrobatch 3, compared to Macrobatch 2. This may be due to the differences in the Pu concentration or the bulk chemical concentrations in the feed material. SRNL is considering the possible reasons for this decline. The DSSHT samples show continued presence of titanium, likely from leaching of the monosodium titanate in ARP. During operation of the ISDP, quantities of salt waste are processed through the Actinide Removal Process (ARP) and MCU in batches of {approx}3800 gallons. Monosodium titanate (MST) is used in ARP to adsorb actinides and strontium from the salt waste and the waste slurry is then filtered prior to sending the clarified salt solution to MCU. The MCU uses solvent extraction technology to extract cesium from salt waste and concentrate cesium in an acidic aqueous stream (Strip Effluent - SE), leaving a decontaminated caustic salt aqueous stream (Decontaminated Salt Solution - DSS). Sampling occurs in the Decontaminated Salt Solution Hold Tank (DSSHT) and Strip Effluent Hold Tank (SEHT) in the MCU process. The MCU sample plan requires that batches be sampled and analyzed for plutonium and strontium content by Savannah River National Lab (SRNL) to determine MST effectiveness. The cesium measurement is used to monitor cesium removal effectiveness and the inductively coupled plasma emission spectroscopy (ICPES) is

  16. Kidney Shear Wave Speed Values in Subjects with and without Renal Pathology and Inter-Operator Reproducibility of Acoustic Radiation Force Impulse Elastography (ARFI) - Preliminary Results

    PubMed Central

    Bob, Flaviu; Bota, Simona; Sporea, Ioan; Sirli, Roxana; Petrica, Ligia; Schiller, Adalbert

    2014-01-01

    Aim to assess the inter-operator reproducibility of kidney shear wave speed, evaluated by means of Acoustic Radiation Force Impulse (ARFI) elastography, and the factors which influence it. Methods Our prospective pilot study included 107 subjects with or without kidney pathology in which kidney shear wave speed was evaluated by means of ARFI elastography. Intraclass correlation coefficient (ICC) was used to assess ARFI elastography reproducibility. Results A strong agreement was obtained between kidney shear wave speed measurements obtained by the two operators: ICC = 0.71 (right kidney) and 0.69 (left kidney). Smaller ICCs were obtained in “healthy subjects”, as compared to patients with kidney diseases (0.68 vs. 0.75), in women as compared with men (0.59 vs. 0.78), in subjects younger than 50 years as compared with those aged at least 50 years (0.63 vs. 0.71), in obese as compared with normal weight and overweight subjects (0.36 vs. 0.66 and 0.78) and in case of measurements depth <4 cm or >6 cm as compared with those performed at a depth of 4–6 cm from the skin (0.32 and 0.60 vs. 0.81). Conclusion ARFI elastography is a reproducible method for kidney shear wave speed assessment. PMID:25426849

  17. Operational comparison of bubble (super heated drop) dosimetry results with routine albedo thermoluminescent dosimetry for a selected group of Pu-238 workers at Los Alamos National Laboratory

    SciTech Connect

    Romero, L.L.; Hoffman, J.M.; Foltyn, E.M.; Buhl, T.E.

    1999-03-01

    This paper is an operational study that compares the use of albedo thermoluminescent dosimeters with bubble dosimeters to determine whether bubble dosimeters do provide a useful daily ALARA tool that can yield measurements close to the dose-of-record. A group of workers at the Los Alamos National Laboratory (LANL) working on the Radioactive Thermoelectric Generators (RTG) for the NASA Cassini space mission wore both bubble dosimeters and albedo dosimeters over a period from 1993 through 1996. The bubble dosimeters were issued and read on a daily basis and the data were used as an ALARA tool. The personnel albedo dosimeter was processed on monthly basis and used as the dose-of-record. The results of this study indicated that cumulative bubble dosimetry results agreed with whole-body albedo dosimetry results within about 37% on average. However it was observed that there is a significant variability of the results on an individual basis both month-to-month and from one individual to another.

  18. Direct liquefaction of biomass: Results from operation of continuous bench scale unit in liquefaction of water slurries of Douglas fir wood

    NASA Astrophysics Data System (ADS)

    Schaleger, L. L.; Figueroa, C.; Davis, H. G.

    1982-05-01

    A continuous liquefaction unit (CLU) is discussed. The operation was single pass, feeding water slurries of prehydrolyzed Douglas fir wood (LBL process). Significant differences from results with the oil slurry, high oil, and water recycle process (PERC process) were found. The LBL process, at practicable temperatures and residence times, makes somewhat less wood oil and considerably more water-soluble product than does PERC. Consumption of carbon monoxide in LBL, other than by water gas shift reaction, is minimal, as opposed to several tenths of a mole per 100 grams of wood in PERC. Replacement of carbon monoxide with hydrogen as reactant gas makes little or no difference in yield distribution or product analysis. Progress in characterizing the oil and water-soluble product, the overall stoichiometry of the LBL and PERC processes, and the role of formate ion are described.

  19. Solar engineering - 1981; Proceedings of the Third Annual Conference on Systems Simulation, Economic Analysis/Solar Heating and Cooling Operational Results, Reno, NV, April 27-May 1, 1981

    NASA Astrophysics Data System (ADS)

    Reid, R. L.; Murphy, L. M.; Ward, D. S.

    Progress made toward the commercialization of solar energy technologies as of 1981 is assessed, and attention is given to the future uses and impacts of solar energy. Attention is given to the results of several years of monitoring and modifying solar heating and cooling on residential and commercial structures. Solar system simulation and analysis methods are reviewed, covering the performance and operations of passive and active systems, thermosyphon systems, heat pumps and phase change systems. Simulations of system components are discussed, as are means to validate existing computer simulation codes, particularly the TRNSYS program. Control systems and logic for collector systems are explored, including analyses of building loads and climates, and numerical models of the economics of solar heating systems are presented. Performance simulations and economic analyses are also outlined for wind and photovoltaic systems, and for industrial solar heating systems. Finally, fundamental studies of corrosion, steam flow, wind loading, and scaling in solar systems are described.

  20. Analysis of Non-Standard Lightning Impulse Voltage for Actual Substation and Generation Circuit

    NASA Astrophysics Data System (ADS)

    Okabe, Shigemitsu; Koutou, Masanori; Yuasa, Sadayuki; Suzuki, Toshiyuki; Rokunohe, Toshiaki; Yamagiwa, Tokio

    Evaluation of lightning surge waveforms that actually enter into substations is important when investigating the test voltage of electric power equipment. The standard lightning impulse waveform (1.2/50μs) is used for factory tests. However, the actual lightning surge waveforms in actual substations are complex waveforms in which various different oscillations are superimposed. Investigation of insulation characteristics of equipment against the complex waveforms and the standard one has significant importance. We analyzed these waveforms entering actual substations with respect to the insulation characteristics of gas insulated switchigear (GIS). From the results, we defined four types of non-standard lightning impulse waveforms. Then non-standard lightning impulse voltage is generated by an equipment circuit which is consisted of an impulse generator (IG), R, L and C is analyzed with EMTP. Voltage time characteristics were evaluated from the obtained impulse voltages.

  1. Correlation between erythropoietic activity and body growth rate in hypertransfused polycythemic growing rats as the result of an erythropoietin-dependent operating mechanism

    SciTech Connect

    Bozzini, C.E.; Alippi, R.M.; Barcelo, A.C.; Caro, J.

    1989-02-01

    The established relationship between erythropoietic activity and body growth rate in the polycythemic growing rat could be the result of either an erythropoietin (EPO)-dependent or an EPO-independent operating mechanism. The present study was thus undertaken to elucidate the nature of the aforementioned mechanism by assessing the ratio between plasma immunoreactive EPO (iEPO) concentration and erythropoietic activity in young hypertransfused rats for different body growth rates. Red blood cell (RBC)-59Fe uptake was about 75% in 21-day-old rats; it rapidly decreased with time when the animals were placed on a protein-free diet, approaching a level of about 1% by the 10th day of protein starvation. Over the same period plasma iEPO decreased from 55 mU/ml to 7 mU/ml. Body growth rate was 0. Following this ''protein depletion period'' the rats received diets containing different amounts of casein (''protein repletion period'') added isocalorically to the protein-free diet to elicit a rise in body growth rate. Statistically significant relationships (p less than 0.001) were found between dietary casein concentration and body growth rate (r = 0.991), dietary casein concentration and RBC-59Fe uptake (r = 0.991), dietary casein concentration and plasma iEPO level (r = 0.992), body growth rate and RBC-59Fe (r = 0.986), and body growth rate and plasma iEPO level (r = 0.994) in hypertransfused polycythemic rats during the protein repletion period. These findings suggest that the correlation between erythropoietic activity and growth rate in the growing rat is the result of an erythropoietin-dependent operating mechanism, which appears to be independent of the ratio tissue oxygen supply/tissue oxygen demand.

  2. Road map to scaling-up: translating operations research study’s results into actions for expanding medical abortion services in rural health facilities in Nepal

    PubMed Central

    2014-01-01

    Background Identifying unsafe abortion among the major causes of maternal deaths and respecting the rights to health of women, in 2002, the Nepali parliament liberalized abortion up to 12 weeks of pregnancy on request. However, enhancing women’s awareness on and access to safe and legal abortion services, particularly in rural areas, remains a challenge in Nepal despite a decade of the initiation of safe abortion services. Methods Between January 2011 and December 2012, an operations research study was carried out using quasi-experimental design to determine the effectiveness of engaging female community health volunteers, auxiliary nurse midwives, and nurses to provide medical abortion services from outreach health facilities to increase the accessibility and acceptability of women to medical abortion. This paper describes key components of the operations research study, key research findings, and follow-up actions that contributed to create a conducive environment and evidence in scaling up medical abortion services in rural areas of Nepal. Results It was found that careful planning and implementation, continuous advocacy, and engagement of key stakeholders, including key government officials, from the planning stage of study is not only crucial for successful completion of the project but also instrumental for translating research results into action and policy change. While challenges remained at different levels, medical abortion services delivered by nurses and auxiliary nurse midwives working at rural outreach health facilities without oversight of physicians was perceived to be accessible, effective, and of good quality by the service providers and the women who received medical abortion services from these rural health facilities. Conclusions This research provided further evidence and a road-map for expanding medical abortion services to rural areas by mid-level service providers in minimum clinical settings without the oversight of physicians, thus

  3. Feasibility and Operational Performance of Tuberculosis Detection by Loop-Mediated Isothermal Amplification Platform in Decentralized Settings: Results from a Multicenter Study.

    PubMed

    Gray, Christen M; Katamba, Achilles; Narang, Pratibha; Giraldo, Jorge; Zamudio, Carlos; Joloba, Moses; Narang, Rahul; Paramasivan, C N; Hillemann, Doris; Nabeta, Pamela; Amisano, Danielle; Alland, David; Cobelens, Frank; Boehme, Catharina C

    2016-08-01

    Currently available nucleic acid amplification platforms for tuberculosis (TB) detection are not designed to be simple or inexpensive enough to implement in decentralized settings in countries with a high burden of disease. The loop-mediated isothermal amplification platform (LAMP) may change this. We conducted a study in adults with symptoms suggestive of TB in India, Uganda, and Peru to establish the feasibility of using TB-LAMP (Eiken Chemical Co.) in microscopy laboratories compared with using smear microscopy against a reference standard of solid and liquid cultures. Operational characteristics were evaluated as well. A total of 1,777 participants met the eligibility criteria and were included for analysis. Overall, TB-LAMP sensitivities among culture-positive samples were 97.2% (243/250; 95% confidence interval [CI], 94.3% to 98.2%) and 62.0% (88/142; 95% CI, 53.5% to 70.0%) for smear-positive and smear-negative TB, respectively, but varied widely by country and operator. Specificities ranged from 94.5% (446/472; 95% CI, 92.0% to 96.4%) to 98.0% (350/357; 95% CI, 96.0% to 99.2%) by country. A root cause analysis identified high temperatures, high humidity, and/or low reaction volumes as possible causes for false-positive results, as they may result in nonspecific amplification. The study was repeated in India with training focused on vulnerable steps and an updated protocol; 580 participants were included for analysis. Specificity in the repeat trial was 96.6% (515/533; 95% CI, 94.7% to 97.9%). To achieve acceptable performance of LAMP at the microscopy center level, significant training and infrastructure requirements are necessary. PMID:27194691

  4. The Partition Intervalometer: A Programmable Underwater Timer for Marking Accumulated Sediment Profiles Collected in Anderson Sediment Traps: Development, Operation, Testing Procedures, and Field Results

    USGS Publications Warehouse

    Rendigs, Richard R.; Anderson, Roger Y.; Xu, Jingping; Davis, Raymond E.; Bergeron, Emile M.

    2009-01-01

    This manual illustrates the development of a programmable instrument designed to deploy a series of wafer-shaped discs (partitions) into the collection tube of a sediment trap in various aquatic environments. These hydrodynamically shaped discs are deployed at discrete time intervals from the Intervalometer and provide markers that delineate time intervals within the sediments that accumulate in the collection tube. The timer and mechanical system are lodged in an air-filled, water-tight pressure housing that is vertically hung within the confines of a cone-shaped sediment trap. The instrumentation has been operationally pressure tested to an equivalent water depth of approximately 1 km. Flaws discovered during extensive laboratory and pressure testing resulted in the implementation of several mechanical modifications (such as a redesign of the rotor and the discs) that improved the operation of the rotor assembly as well as the release of discs through the end cap. These results also identified a preferred azimuth placement of the rotor disc relative to the drop hole of the end cap. In the initial field trial, five sediment traps and coupled Intervalometers were attached to moored arrays and deployed at two sites off the coast of Southern California for approximately 8 months. Each of the instruments released 18 discs at the programmed 10 day intervals, except one unit, which experienced a malfunction after approximately 4 months. Most of the discs oriented in a near-horizontal position upon the surface of the sediment in the collection tubes. Sampling of the sediments for geochemical analyses was improved by these clearly defined markers, which indicated the changes in the flux and nature of sediments accumulated during the deployment period of each sediment trap.

  5. HIV Testing among Patients with Presumptive Tuberculosis: How Do We Implement in a Routine Programmatic Setting? Results of a Large Operational Research from India

    PubMed Central

    Kumar, Ajay MV; Gupta, Devesh; Kumar, Ashok; Gupta, R. S.; Kanchar, Avinash; Rao, Raghuram; Shastri, Suresh; Suryakanth, MD; Rangaraju, Chethana; Naik, Balaji; Guddemane, Deepak K.; Bhat, Prashant; Nair, Achuthan Sreenivas; Harries, Anthony David; Dewan, Puneet

    2016-01-01

    Background In March 2012, World Health Organization recommended that HIV testing should be offered to all patients with presumptive TB (previously called TB suspects). How this is best implemented and monitored in routine health care settings in India was not known. An operational research was conducted in Karnataka State (South India, population 64 million, accounts for 10% of India’s HIV burden), to test processes and learn results and challenges of screening presumptive TB patients for HIV within routine health care settings. Methods In this cross-sectional study conducted between January-March 2012, all presumptive TB patients attending public sector sputum microscopy centres state-wide were offered HIV testing by the laboratory technician, and referred to the nearest public sector HIV counselling and testing services, usually within the same facility. The HIV status of the patients was recorded in the routine TB laboratory form and TB laboratory register. The laboratory register was compiled to obtain the number of presumptive TB patients whose HIV status was ascertained, and the number found HIV positive. Aggregate data on reasons for non-testing were compiled at district level. Results Overall, 115,308 patients with presumptive TB were examined for sputum smear microscopy at 645 microscopy centres state-wide. Of these, HIV status was ascertained for 62,847(55%) among whom 7,559(12%) were HIV-positive, and of these, 3,034(40%) were newly diagnosed. Reasons for non-testing were reported for 37,700(72%) of the 52,461 patients without HIV testing; non-availability of testing services at site of sputum collection was cited by health staff in 54% of respondents. Only 4% of patients opted out of HIV testing. Conclusion Offering HIV testing routinely to presumptive TB patients detected large numbers of previously-undetected instances of HIV infection. Several operational challenges were noted which provide useful lessons for improving uptake of HIV testing in this

  6. Comparison of actual and predicted energy savings in Minnesota gas-heated single-family homes

    SciTech Connect

    Hirst, E.; Goeltz, R.

    1984-03-01

    Data available from a recent evaluation of a home energy audit program in Minnesota are sufficient to allow analysis of the actual energy savings achieved in audited homes and of the relationship between actual and predicted savings. The program, operated by Northern States Power in much of the southern half of the state, is part of Minnesota's version of the federal Residential Conservation Service. NSP conducted almost 12 thousand RCS audits between April 1981 (when the progam began) and the end of 1982. The data analyzed here, available for 346 homes that obtained an NSP energy audit, include monthly natural gas bills from October 1980 through April 1983; heating degree day data matched to the gas bills; energy audit reports; and information on household demographics, structure characteristics, and recent conservation actions from mail and telephone surveys. The actual reduction in weather-adjusted natural gas use between years 1 and 3 averaged 19 MBtu across these homes (11% of preprogram consumption); the median value of the saving was 16 MBtu/year. The variation in actual saving is quite large: gas consumption increased in almost 20% of the homes, while gas consumption decreased by more than 50 MBtu/year in more than 10% of the homes. These households reported an average expenditure of almost $1600 for the retrofit measures installed in their homes; the variation in retrofit cost, while large, was not as great as the variation in actual natural gas savings.

  7. Clinical learning environments (actual and expected): perceptions of Iran University of Medical Sciences nursing students

    PubMed Central

    Bigdeli, Shoaleh; Pakpour, Vahid; Aalaa, Maryam; Shekarabi, Robabeh; Sanjari, Mahnaz; Haghani, Hamid; Mehrdad, Neda

    2015-01-01

    Background: Educational clinical environment has an important role in nursing students' learning. Any difference between actual and expected clinical environment will decrease nursing students’ interest in clinical environments and has a negative correlation with their clinical performance. Methods: This descriptive cross-sectional study is an attempt to compare nursing students' perception of the actual and expected status of clinical environments in medical-surgical wards. Participants of the study were 127 bachelor nursing students of Iran University of Medical Sciences in the internship period. Data gathering instruments were a demographic questionnaire (including sex, age, and grade point average), and the Clinical Learning Environment Inventory (CLEI) originally developed by Professor Chan (2001), in which its modified Farsi version (Actual and Preferred forms) consisting 42 items, 6 scales and 7 items per scale was used. Descriptive and inferential statistics (t-test, paired t-test, ANOVA) were used for data analysis through SPSS version 16. Results: The results indicated that there were significant differences between the preferred and actual form in all six scales. In other word, comparing with the actual form, the mean scores of all items in the preferred form were higher. The maximum mean difference was in innovation and the highest mean difference was in involvement scale. Conclusion: It is concluded that nursing students do not have a positive perception of their actual clinical teaching environment and this perception is significantly different from their perception of their expected environment. PMID:26034726

  8. The Relationship between Barriers to Birth Control Use and Actual Birth Control Use among Mexican-American Adolescents.

    ERIC Educational Resources Information Center

    Pesa, Jacqueline A.; Mathews, Jeff

    2000-01-01

    Examines the relationship between barriers to using birth control and actual use of birth control among Mexican American adolescents (N=26,666). Results show that nonusers had significantly higher barrier scores compared with users of birth control. These results indicate that attitudes toward birth control are associated with actual birth control…

  9. The FAST-T approach for operational, real time, short term hydrological forecasting: Results from the Betania Hydropower Reservoir case study

    NASA Astrophysics Data System (ADS)

    Domínguez, Efraín; Angarita, Hector; Rosmann, Thomas; Mendez, Zulma; Angulo, Gustavo

    2013-04-01

    A viable quantitative hydrological forecasting service is a combination of technological elements, personnel and knowledge, working together to establish a stable operational cycle of forecasts emission, dissemination and assimilation; hence, the process for establishing such system usually requires significant resources and time to reach an adequate development and integration in order to produce forecasts with acceptable levels of performance. Here are presented the results of this process for the recently implemented Operational Forecast Service for the Betania's Hydropower Reservoir - or SPHEB, located at the Upper-Magdalena River Basin (Colombia). The current scope of the SPHEB includes forecasting of water levels and discharge for the three main streams affluent to the reservoir, for lead times between +1 to +57 hours, and +1 to +10 days. The core of the SPHEB is the Flexible, Adaptive, Simple and Transient Time forecasting approach, namely FAST-T. This comprises of a set of data structures, mathematical kernel, distributed computing and network infrastructure designed to provide seamless real-time operational forecast and automatic model adjustment in case of failures in data transmission or assimilation. Among FAST-T main features are: an autonomous evaluation and detection of the most relevant information for the later configuration of forecasting models; an adaptively linearized mathematical kernel, the optimal adaptive linear combination or OALC, which provides a computationally simple and efficient algorithm for real-time applications; and finally, a meta-model catalog, containing prioritized forecast models at given stream conditions. The SPHEB is at present feed by the fraction of hydrological monitoring network installed at the basin that has telemetric capabilities via NOAA-GOES satellites (8 stages, approximately 47%) with data availability of about a 90% at one hour intervals. However, there is a dense network of 'conventional' hydro

  10. Correlation of free-response and receiver-operating-characteristic area-under-the-curve estimates: Results from independently conducted FROC/ROC studies in mammography

    PubMed Central

    Zanca, Federica; Hillis, Stephen L.; Claus, Filip; Van Ongeval, Chantal; Celis, Valerie; Provoost, Veerle; Yoon, Hong-Jun; Bosmans, Hilde

    2012-01-01

    Purpose: From independently conducted free-response receiver operating characteristic (FROC) and receiver operating characteristic (ROC) experiments, to study fixed-reader associations between three estimators: the area under the alternative FROC (AFROC) curve computed from FROC data, the area under the ROC curve computed from FROC highest rating data, and the area under the ROC curve computed from confidence-of-disease ratings. Methods: Two hundred mammograms, 100 of which were abnormal, were processed by two image-processing algorithms and interpreted by four radiologists under the FROC paradigm. From the FROC data, inferred-ROC data were derived, using the highest rating assumption. Eighteen months afterwards, the images were interpreted by the same radiologists under the conventional ROC paradigm; conventional-ROC data (in contrast to inferred-ROC data) were obtained. FROC and ROC (inferred, conventional) data were analyzed using the nonparametric area-under-the-curve (AUC), (AFROC and ROC curve, respectively). Pearson correlation was used to quantify the degree of association between the modality-specific AUC indices and standard errors were computed using the bootstrap-after-bootstrap method. The magnitude of the correlations was assessed by comparison with computed Obuchowski-Rockette fixed reader correlations. Results: Average Pearson correlations (with 95% confidence intervals in square brackets) were: Corr(FROC, inferred ROC) = 0.76[0.64, 0.84] > Corr(inferred ROC, conventional ROC) = 0.40[0.18, 0.58] > Corr (FROC, conventional ROC) = 0.32[0.16, 0.46]. Conclusions: Correlation between FROC and inferred-ROC data AUC estimates was high. Correlation between inferred- and conventional-ROC AUC was similar to the correlation between two modalities for a single reader using one estimation method, suggesting that the highest rating assumption might be questionable. PMID:23039631

  11. Hand-held echocardiography in the setting of pre-operative cardiac evaluation of patients undergoing non-cardiac surgery: results from a randomized pilot study.

    PubMed

    Cavallari, Ilaria; Mega, Simona; Goffredo, Costanza; Patti, Giuseppe; Chello, Massimo; Di Sciascio, Germano

    2015-06-01

    Transthoracic echocardiography is not a routine test in the pre-operative cardiac evaluation of patients undergoing non-cardiac surgery but may be considered in those with known heart failure and valvular heart disease or complaining cardiac symptoms. In this setting, hand-held echocardiography (HHE) could find a potential application as an alternative to standard echocardiography in selected patients; however, its utility in this context has not been investigated. The aim of this pilot study was to evaluate the conclusiveness of HHE compared to standard echocardiography in this subset of patients. 100 patients scheduled for non-cardiac surgery were randomized to receive a standard exam with a Philips Ie33 or a bedside evaluation with a pocket-size imaging device (Opti-Go, Philips Medical System). The primary endpoint was the percentage of satisfactory diagnosis at the end of the examination referred as conclusiveness. Secondary endpoints were the mean duration time and the mean waiting time to perform the exams. No significant difference in terms of conclusiveness between HHE and standard echo was found (86 vs 96%; P = 0.08). Mean duration time of the examinations was 6.1 ± 1.2 min with HHE and 13.1 ± 2.6 min with standard echocardiography (P < 0.001). HHE resulted in a consistent save of waiting time because it was performed the same day of clinical evaluation whereas patients waited 10.1 ± 6.1 days for a standard echocardiography (P < 0.001). This study suggests the potential role of HHE for pre-operative evaluation of selected patients undergoing non-cardiac surgery, since it provided similar information but it was faster and earlier performed compared to standard echocardiography. PMID:25985940

  12. Airborne investigation of bathymetric sills in Godthåbsfjord, Greenland - results from IcePOD and Operation IceBridge

    NASA Astrophysics Data System (ADS)

    Tinto, K. J.; Zappa, C. J.; Bell, R. E.; Frearson, N.; Cochran, J. R.; Boghosian, A.; Porter, D. F.

    2013-12-01

    The bathymetry of Greenlandic fjords is an important boundary condition for understanding circulation within the fjord. This in turn is crucial to the understanding of ocean-ice interactions at the margins of the Greenland ice sheet. Marine-based surveys have identified sills at the heads of many of these fjords, and demonstrated their importance to the circulation patterns within the fjords themselves. The inaccessibility of much of the Greenland fjord system leaves many regions poorly surveyed, with important data gaps remaining in the interior of the fjords. Airborne surveys provide a valuable platform for the study of fjord dynamics by offering wide coverage and the ability to survey otherwise inaccessible regions of fjords. In this study we combine results from Operation IceBridge gravity surveys with visible and infrared imagery from the IcePOD project to investigate circulation, transport, and mixing in Godthåbsfjord, Greenland, at the calving front of Kangiata Nunâta Sermia. The bathymetry of this fjord has been well mapped, but information is sparse from the inner 13 km where the fjord is filled with icebergs. Gravity data show a 4 mGal positive anomaly 10 km from the calving front. Models constrained by the gravity anomaly over a known sill further up the fjord give this newly identified sill a predicted depth of approximately 100 m. IcePOD is a multi-instrument pod flown on an LC130 operated by the New York Air National Guard. During test flights in the summer of 2013 multiple passes were made of the inner, iceberg-filled part of Godthåbsfjord with both visible and infra-red cameras. Here we compare the movement of ice within the fjord with modelled bathymetry from IceBridge to investigate the circulation of the inner part of the fjord.

  13. Correlation of free-response and receiver-operating-characteristic area-under-the-curve estimates: Results from independently conducted FROC/ROC studies in mammography

    SciTech Connect

    Zanca, Federica; Hillis, Stephen L.; Claus, Filip; Van Ongeval, Chantal; Celis, Valerie; Provoost, Veerle; Yoon, Hong-Jun; Bosmans, Hilde

    2012-10-15

    Purpose: From independently conducted free-response receiver operating characteristic (FROC) and receiver operating characteristic (ROC) experiments, to study fixed-reader associations between three estimators: the area under the alternative FROC (AFROC) curve computed from FROC data, the area under the ROC curve computed from FROC highest rating data, and the area under the ROC curve computed from confidence-of-disease ratings. Methods: Two hundred mammograms, 100 of which were abnormal, were processed by two image-processing algorithms and interpreted by four radiologists under the FROC paradigm. From the FROC data, inferred-ROC data were derived, using the highest rating assumption. Eighteen months afterwards, the images were interpreted by the same radiologists under the conventional ROC paradigm; conventional-ROC data (in contrast to inferred-ROC data) were obtained. FROC and ROC (inferred, conventional) data were analyzed using the nonparametric area-under-the-curve (AUC), (AFROC and ROC curve, respectively). Pearson correlation was used to quantify the degree of association between the modality-specific AUC indices and standard errors were computed using the bootstrap-after-bootstrap method. The magnitude of the correlations was assessed by comparison with computed Obuchowski-Rockette fixed reader correlations. Results: Average Pearson correlations (with 95% confidence intervals in square brackets) were: Corr(FROC, inferred ROC) = 0.76[0.64, 0.84] > Corr(inferred ROC, conventional ROC) = 0.40[0.18, 0.58] > Corr (FROC, conventional ROC) = 0.32[0.16, 0.46]. Conclusions: Correlation between FROC and inferred-ROC data AUC estimates was high. Correlation between inferred- and conventional-ROC AUC was similar to the correlation between two modalities for a single reader using one estimation method, suggesting that the highest rating assumption might be questionable.

  14. RESULTS FROM ANALYSIS OF THE FIRST AND SECOND STRIP EFFLUENT COALESCER ELEMENTS FROM RADIOACTIVE OPERATIONS OF THE MODULAR CAUSTIC-SIDE SOLVENT EXTRACTION UNIT

    SciTech Connect

    Peters, T.; Fondeur, F.; Fink, S.

    2011-06-28

    The coalescer elements for the Strip Effluent (SE) acid within the Modular Caustic-Side Solvent Extraction Unit (MCU) experienced elevated differential pressure drop during radioactive operations. Following the end of operations for the first Macrobatch campaign and soon after start of the second Macrobatch campaign, personnel removed the coalescer media and provided to Savannah River National Laboratory (SRNL) for diagnostic investigation of the causes of reduced flow. This report summarizes those studies. Two Strip Effluent (SE) coalescers were delivered to the Savannah River National Laboratory (SRNL). One was removed from the Modular Caustic-Side Solvent Extraction Unit (MCU) between processing of Macrobatch 1 and 2 (coalescer 'Alpha'), and the second was removed from MCU after processing of {approx}24,000 gallons of salt solution (coalescer 'Beta'). Both coalescers underwent the same general strip acid flush program to reduce the dose and were delivered to SRNL for analysis of potential occluding solids. Analysis of Coalescer Alpha indicates the presence of aluminum hydroxide solids and aluminosilicate solids, while analysis of Coalescer Beta indicates the presence of aluminum hydroxide solids, but no aluminosilicates. Leaching studies on sections of both coalescers were performed. The results indicate that the coalescers had different amounts of solids present on them at the time of removal. Finally, samples of free liquids retrieved from both coalescers indicate no excessive amounts of CSSX solvent present. Given the strip acid flushing that occurred in the SE coalescers, the solids we detected on the coalescers are probably indicative of a larger quantity of these solids present before the strip acid flushing. Under this scenario, the excessive pressure drops are due to the solids and not from organic fouling.

  15. Results of the clean-up operation to reduce pollution on flooded agricultural fields after the red mud spill in Hungary.

    PubMed

    Uzinger, Nikolett; Anton, Áron Dániel; Ötvös, Károly; Tamás, Péter; Anton, Attila

    2015-07-01

    In Hungary, the dam of a red mud reservoir breached shortly after noon on October 4, 2010. Approximately 0.7-1 million m(3) highly alkaline red mud with very low dry matter content flowed into the Torna Creek and the surrounding area, covering 1017 ha of agricultural land. Results of the risk assessment of the accident indicated that the red mud should be removed from the surface of fields where it formed a continuous layer of more than 5 cm. After the removal, samples were taken manually from depths of 0.0-0.2 m and 0.2-0.4 m in a sampling grid and background samples unaffected by red mud from the depth of 0.0-0.3 m. Total element contents (Ag, As, Ba, Cd, Co, Cr, Cu, Hg, Mo, Ni, Pb, Sn, Zn, and Na) and pH values were measured, and the results were analysed using correlation analysis and the Kruskal-Wallis probe. Dependence of the measured variables from elevation above sea level was studied using a 10 m by 10 m digital elevation model. Only ∼6.5% of the flooded area was temporarily designated as unsuitable for the production of food and fodder crops. In summary, the clean-up operation can be said to have been a success. PMID:25647492

  16. Stereotactic body radiation therapy (SBRT) for lung malignancies: preliminary toxicity results using a flattening filter-free linear accelerator operating at 2400 monitor units per minute

    PubMed Central

    2013-01-01

    Background Flattening filter-free (FFF) linear accelerators (linacs) are capable of delivering dose rates more than 4-times higher than conventional linacs during SBRT treatments, causing some to speculate whether the higher dose rate leads to increased toxicity owing to radiobiological dose rate effects. Despite wide clinical use of this emerging technology, clinical toxicity data for FFF SBRT are lacking. In this retrospective study, we report the acute and late toxicities observed in our lung radiosurgery experience using a FFF linac operating at 2400 MU/min. Methods We reviewed all flattening filter-free (FFF) lung SBRT cases treated at our institution from August 2010 through July 2012. Patients were eligible for inclusion if they had at least one clinical assessment at least 30 days following SBRT. Pulmonary, cardiac, dermatologic, neurologic, and gastrointestinal treatment related toxicities were scored according to CTCAE version 4.0. Toxicity observed within 90 days of SBRT was categorized as acute, whereas toxicity observed more than 90 days from SBRT was categorized as late. Factors thought to influence risk of toxicity were examined to assess relationship to grade > =2 toxicity. Results Sixty-four patients with >30 day follow up were eligible for inclusion. All patients were treated using 10 MV unflattened photons beams with intensity modulated radiation therapy (IMRT) inverse planning. Median SBRT dose was 48 Gy in 4 fractions (range: 30–60 Gy in 3–5 fractions). Six patients (9%) experienced > = grade 2 acute pulmonary toxicity; no non-pulmonary acute toxicities were observed. In a subset of 49 patients with greater than 90 day follow up (median 11.5 months), 11 pulmonary and three nerve related grade > =2 late toxicities were recorded. Pulmonary toxicities comprised six grade 2, three grade 3, and one each grade 4 and 5 events. Nerve related events were rare and included two cases of grade 2 chest wall pain and one grade 3

  17. The CheMin XRD on the Mars Science Laboratory Rover Curiosity: Construction, Operation, and Quantitative Mineralogical Results from the Surface of Mars

    NASA Technical Reports Server (NTRS)

    Blake, David F.

    2015-01-01

    The Mars Science Laboratory mission was launched from Cape Canaveral, Florida on Nov. 26, 2011 and landed in Gale crater, Mars on Aug. 6, 2012. MSL's mission is to identify and characterize ancient "habitable" environments on Mars. MSL's precision landing system placed the Curiosity rover within 2 km of the center of its 20 X 6 km landing ellipse, next to Gale's central mound, a 5,000 meter high pile of laminated sediment which may contain 1 billion years of Mars history. Curiosity carries with it a full suite of analytical instruments, including the CheMin X-ray diffractometer, the first XRD flown in space. CheMin is essentially a transmission X-ray pinhole camera. A fine-focus Co source and collimator transmits a 50µm beam through a powdered sample held between X-ray transparent plastic windows. The sample holder is shaken by a piezoelectric actuator such that the powder flows like a liquid, each grain passing in random orientation through the beam over time. Forward-diffracted and fluoresced X-ray photons from the sample are detected by an X-ray sensitive Charge Coupled Device (CCD) operated in single photon counting mode. When operated in this way, both the x,y position and the energy of each photon are detected. The resulting energy-selected Co Kalpha Debye-Scherrer pattern is used to determine the identities and amounts of minerals present via Rietveld refinement, and a histogram of all X-ray events constitutes an X-ray fluorescence analysis of the sample.The key role that definitive mineralogy plays in understanding the Martian surface is a consequence of the fact that minerals are thermodynamic phases, having known and specific ranges of temperature, pressure and composition within which they are stable. More than simple compositional analysis, definitive mineralogical analysis can provide information about pressure/temperature conditions of formation, past climate, water activity and the like. Definitive mineralogical analyses are necessary to establish

  18. Safety of patients--actual problem of modern medicine (review).

    PubMed

    Tsintsadze, Neriman; Samnidze, L; Beridze, T; Tsintsadze, M; Tsintsadze, Nino

    2011-09-01

    Safety of patients is actual problem of up-to-date medicine. The current successful treatment of various sicknesses is achieved by implementation in clinical practice such medical preparations (medications), which are characterized with the high therapeutic activity, low toxicity and prolonged effects. In spite of evidence of the pharmacotherapeutical advances, the frequency of complications after medication has grown - that is why the safety of patients is the acute actual problem of medicine and ecological state of human population today. PMID:22156680

  19. Choice of surgical access for retroperitoneoscopic ureterolithotomy according to the results of 3D reconstruction of operational zone agreed with the patient: initial experience

    PubMed Central

    Bashirov, Valerii I.; Furman, Yakov A.; Rozhentsov, Alexey A.; Yeruslanov, Ruslan V.; Kudryavtsev, Alexandr A.

    2013-01-01

    Introduction For the procedure retroperitoneoscopic ureterolithotomy, the problems of access choice and thus visualization with utilizing minimally invasive surgical access (either with gasless single port method or gas insufflation) are solved. The decisions are based on the method of presurgery planning, grounded on matching the patient with a 3D model of the zone of surgical interest reconstructed according to the results of tomographic examination. Material and methods We used a hardware–software complex (HSC) for virtual modeling of the surgery zone and choosing the optimum points for minimally invasive surgical access. The HSC was recruited to choose optimum surgical access, realize presurgery planning, and estimation of the safety of the way of access chosen. The original method of matching the system of coordinates of a virtual model with the patient was offered. Results 12 patients with the calculus in the upper part of ureter averaging 11.5 (9–14) mm in size underwent gasless retroperitoneoscopic ureterolithotomy with use of the HSC. Mean age of the patients was 36.4 (25–49) years old. The surgeries lasted an average of 35.5 (25–40) minutes. Blood loss was averaged at 55.0 (30–90) ml. Healing by first intention was registered with all the patients. The mean hospitalization time was 6.0 (4–7) days. There were neither any complications nor difficulties, nor conversions from incorrectly chosen surgical access. Conclusions The choice of the optimum surgical access according to the results of a virtual 3D model of the operation zone, matching the system of coordinates of the model with patient concurrence, and presurgery planning, was effective in cases of gasless single port and with gas insufflation retroperitoneoscopic ureterolithotomy. PMID:24757541

  20. Implementation of conduct of operations at Paducah uranium hexafluoride (UF{sub 6}) sampling and transfer facility

    SciTech Connect

    Penrod, S.R.

    1991-12-31

    This paper describes the initial planning and actual field activities associated with the implementation of {open_quotes}Conduct of Operations{close_quotes}. Conduct of Operations is an operating philosophy that was developed through the Institute of Nuclear Power Operations (INPO). Conduct of Operations covers many operating practices and is intended to provide formality and discipline to all aspects of plant operation. The implementation of these operating principles at the UF{sub 6} Sampling and Transfer Facility resulted in significant improvements in facility operations.

  1. Implementation of conduct of operations at Paducah uranium hexafluoride (UF{sub 6}) sampling and transfer facility

    SciTech Connect

    Penrod, S.R.

    1991-12-31

    This paper describes the initial planning and actual field activities associated with the implementation of {open_quotes}Conduct of Operations{close_quotes}, Conduct of Operations is an operating philosophy that was developed through the Institute of Nuclear Power Operations (INPO). Conduct of Operations covers many operating practices and is intended to provide formality and discipline to all aspects of plant operation. The implementation of these operating principles at the UF{sub 6} Sampling and Transfer Facility resulted in significant improvements in facility operations.

  2. Long-term results for the uncemented Zweymuller/Alloclassic hip endoprosthesis. A 15-year minimum follow-up of 320 hip operations.

    PubMed

    Suckel, Andreas; Geiger, Friedrich; Kinzl, Lothar; Wulker, Nikolaus; Garbrecht, Manfred

    2009-09-01

    A follow-up study of 15 (15-17) years of 320 consecutive Zweymuller total hip arthroplasties is presented. Age at surgery was 67 (29-99) years. A total of 164 (51.3%) patients had died. Clinical and radiological examinations were available for 97 (30.3%), phone interviews and radiological examinations for 4 (1.3%) hips, and phone follow-ups for 49 (15.3%). There were 6 (1.9%) patients who were lost to follow-up. The Harris Hip Score results in a median value of 88. According to the Kaplan-Meier method, a survival rate of the cup/inlay of 98% (95% confidence interval, 95%-99%) after 17 years was achieved. For the stem/head, the survival rate was 98% (95% confidence interval, 94%-99%). In 95.2% of patients, no operative revision was required. The rate of aseptic loosening was 2% for the acetabular and 1% for the femoral component. PMID:18789635

  3. Anterior callosal section is useful for the removal of large tumors invading the dorsal part of the anterior third ventricle: operative technique and results.

    PubMed

    Shiramizu, Hideki; Hori, Tomokatsu; Matsuo, Seigo; Niimura, Kaku; Yoshimoto, Haruko; Ishida, Atsushi; Asakuno, Keizoh; Yuzawa, Miki; Moriyama, Takashi

    2013-07-01

    Large tumors invading the dorsal part of the anterior third ventricle are difficult to manage. The anterior transcallosal approach is usually used to manage these tumors. In our clinic, anterior callosal section was combined with the anterior interhemispheric (AIH) translamina terminalis approach for these tumors with excellent results. The AIH approach is useful for removing tumors in and around the anterior part of the third ventricle. However, AIH alone is insufficient for large tumors invading the dorsal part of the anterior third ventricle. In such situations, simple anterior callosal section enables the neurosurgeon to extirpate the caudal part of the tumors deeply hidden from operative field, sparing the foramen of Monro, fornix, etc. We treated four large tumors (malignant teratoma, recurrent chordoid glioma, recurrent papillary tumor of pineal region occupying the third ventricle, and paraventricular meningioma) without major complications. The malignant teratoma case exhibited no recurrence with >10 years follow-up. The chordoid glioma and papillary tumor of pineal region were totally removed. The meningioma was subtotally removed except only a small tumor around the bilateral anterior cerebral artery. This simple technique is a new way to manage difficult large lesions in and around the third ventricle. PMID:23568695

  4. Influence of binder properties, method of addition, powder type and operating conditions on fluid-bed melt granulation and resulting tablet properties.

    PubMed

    Abberger, T

    2001-12-01

    The aim of the study was to investigate melt granulation in a laboratory scale fluid-bed granulator with respect to granule growth, granule properties and resulting tablet properties. The parameters investigated were method of addition of PEG (spray-on or addition as flakes), binder concentration, PEG type (3000, 4000 and 6000, sprayed-on), size (PEG 4000, added as three different sized flakes), powder type (two different sized lactose types and corn starch) and operating conditions (volume air flow and heating temperature). Addition of binder as flakes led to layering as a growth mechanism when the size of the flakes was high. Coalescence occurred when the size was low. Coalescence also occurred when spraying was the method of addition. Due to the greater viscosity of the PEG 6000 melt it produced bigger granules than 3000 or 4000. The influence of volume air flow was moderate and the influence of heating temperature in the range of 70-90 degrees C was very low with both methods of addition. The disintegration time of tablets from granules where PEG was added as flakes was shorter than from granules where PEG was sprayed-on. The latter method of binder addition led to tablets which did not disintegrate but eroded. This was apparently caused by formation of a binder matrix, which could not be destroyed by the disintegrant. PMID:11802658

  5. Layout and results from the initial operation of the high-resolution x-ray imaging crystal spectrometer on the Large Helical Device

    SciTech Connect

    Pablant, N. A.; Bitter, M.; Delgado-Aparicio, L.; Hill, K. W.; Lazerson, S.; Roquemore, A. L.; Gates, D.; Monticello, D.; Nielson, H.; Reiman, A.; Goto, M.; Morita, S.; Yamada, H.; Reinke, M.; Rice, J. E.

    2012-08-15

    First results of ion and electron temperature profile measurements from the x-ray imaging crystal spectrometer (XICS) diagnostic on the Large Helical Device (LHD) are presented. This diagnostic system has been operational since the beginning of the 2011 LHD experimental campaign and is the first application of the XICS diagnostic technique to helical plasma geometry. The XICS diagnostic provides measurements of ion and electron temperature profiles in LHD with a spatial resolution of 2 cm and a maximum time resolution of 5 ms (typically 20 ms). Ion temperature profiles from the XICS diagnostic are possible under conditions where charge exchange recombination spectroscopy (CXRS) is not possible (high density) or is perturbative to the plasma (low density or radio frequency heated plasmas). Measurements are made by using a spherically bent crystal to provide a spectrally resolved 1D image of the plasma from line integrated emission of helium-like Ar{sup 16+}. The final hardware design and configuration are detailed along with the calibration procedures. Line-integrated ion and electron temperature measurements are presented, and the measurement accuracy is discussed. Finally central temperature measurements from the XICS system are compared to measurements from the Thomson scattering and CXRS systems, showing excellent agreement.

  6. Long-term results of post-operative radiation therapy following mastectomy with or without chemotherapy in Stage I--III breast cancer

    SciTech Connect

    Uematsu, Minoru; Bornstein, B.A.; Recht, A.; Abner, A.; Silver, B. ); Come, S.E. Harvard Medical School, Boston, MA ); Shulman, L.N. Harvard Medical School, Boston, MA ); Harris, J.R.

    1993-04-02

    The purpose of this work was to determine the risk of local-regional failure following post-mastectomy radiotherapy and the incidence of complications associated with such treatment. The authors retrospectively analyzed the results in 309 patients with Stage I--III invasive breast cancer treated with post-mastectomy radiation therapy between 1975 and 1985. The median radiotherapy dose was 45 Gy in 1.8 to 2.25 Gy fractions. One hundred forty-seven (48%) of the patients received adjuvant systemic chemotherapy with 115 (78%) of these receiving a CMF-based or doxorubicin-containing regime. The median follow-up time of surviving patients was 130 months (range, 28 to 191 months) after mastectomy. Seventeen patients (6%) developed a local-regional failure at an interval of 4 to 87 months after radiotherapy. Moderate or severe complications related to radiotherapy and requiring treatment were uncommon. Symptomatic radiation pneumonitis occurred in four patients (1.3%), arm edema in 18 (5.8%), and brachial plexopathy in 2 (0.6%). The authors conclude that post-operative radiotherapy is a safe and effective means of reducing local-regional failure following mastectomy. The efficacy of post-mastectomy radiotherapy in improving survival should be addressed in new large randomized controlled studies. 33 refs., 1 fig., 3 tabs.

  7. Changes in waste stabilisation pond performance resulting from the retrofit of activated sludge treatment upstream: part II--Management and operating issues.

    PubMed

    Sweeney, D G; O'Brien, M J; Cromar, N J; Fallowfield, H J

    2005-01-01

    Bolivar Wastewater Treatment Plant (WWTP) was originally commissioned with trickling filter secondary treatment, followed by waste stabilisation pond (WSP) treatment and marine discharge. In 1999, a dissolved air flotation/filtration (DAFF) plant was commissioned to treat a portion of the WSP effluent for horticultural reuse. In 2001, the trickling filters were replaced with activated sludge treatment. A shift in WSP ecology became evident soon after this time, characterised by a statistically significant reduction in algal counts in the pond effluent, and increased variability in algal counts and occasional population crashes in the ponds. While the photosynthetic capacity of the WSPs has been reduced, the concomitant reduction in organic loading has meant that the WSPs have not become overloaded. As a result of the improvement in water quality leaving the ponds, significant cost savings and improved product water quality have been realised in the subsequent DAFF treatment stage. A number of operating issues have arisen from the change, however, including the re-emergence of a midge fly nuisance at the site. Control of midge flies using chemical spraying has negated the cost savings realised in the DAFF treatment stage. While biomanipulation of the WSP may provide a less aggressive method of midge control, this case demonstrates the difficulty of predicting in advance all ramifications of a retrospective process change. PMID:16114659

  8. Actual Versus Estimated Utility Factor of a Large Set of Privately Owned Chevrolet Volts

    SciTech Connect

    John Smart; Thomas Bradley; Stephen Schey

    2014-04-01

    In order to determine the overall fuel economy of a plug-in hybrid electric vehicle (PHEV), the amount of operation in charge depleting (CD) versus charge sustaining modes must be determined. Mode of operation is predominantly dependent on customer usage of the vehicle and is therefore highly variable. The utility factor (UF) concept was developed to quantify the distance a group of vehicles has traveled or may travel in CD mode. SAE J2841 presents a UF calculation method based on data collected from travel surveys of conventional vehicles. UF estimates have been used in a variety of areas, including the calculation of window sticker fuel economy, policy decisions, and vehicle design determination. The EV Project, a plug-in electric vehicle charging infrastructure demonstration being conducted across the United States, provides the opportunity to determine the real-world UF of a large group of privately owned Chevrolet Volt extended range electric vehicles. Using data collected from Volts enrolled in The EV Project, this paper compares the real-world UF of two groups of Chevrolet Volts to estimated UF's based on J2841. The actual observed fleet utility factors (FUF) for the MY2011/2012 and MY2013 Volt groups studied were observed to be 72% and 74%, respectively. Using the EPA CD ranges, the method prescribed by J2841 estimates a FUF of 65% and 68% for the MY2011/2012 and MY2013 Volt groups, respectively. Volt drivers achieved higher percentages of distance traveled in EV mode for two reasons. First, they had fewer long-distance travel days than drivers in the national travel survey referenced by J2841. Second, they charged more frequently than the J2841 assumption of once per day - drivers of Volts in this study averaged over 1.4 charging events per day. Although actual CD range varied widely as driving conditions varied, the average CD ranges for the two Volt groups studied matched the EPA CD range estimates, so CD range variation did not affect FUF results.

  9. A comprehensive approach to actual polychlorinated biphenyls environmental contamination.

    PubMed

    Risso, F; Magherini, A; Ottonelli, M; Magi, E; Lottici, S; Maggiolo, S; Garbarino, M; Narizzano, R

    2016-05-01

    Worldwide polychlorinated biphenyls (PCBs) pollution is due to complex mixtures with high number of congeners, making the determination of total PCBs in the environment an open challenge. Because the bulk of PCBs production was made of Aroclor mixtures, this analysis is usually faced by the empirical mixture identification via visual inspection of the chromatogram. However, the identification reliability is questionable, as patterns in real samples are strongly affected by the frequent occurrence of more than one mixture. Our approach is based on the determination of a limited number of congeners chosen to enable objective criteria for Aroclor identification, summing up the advantages of congener-specific analysis with the ones of total PCBs determination. A quantitative relationship is established between congeners and any single mixture, or mixtures combination, leading to the identification of the actual contamination composition. The approach, due to its generality, allows the use of different sets of congeners and any technical mixture, including the non-Aroclor ones. The results confirm that PCB environmental pollution in northern Italy is based on Aroclor. Our methodology represents an important tool to understand the source and fate of the PCBs contamination. PMID:26805927

  10. Assessing daily actual evapotranspiration through energy balance: an experiment to evaluate the selfpreservation hypothesis with acquisition time

    NASA Astrophysics Data System (ADS)

    Maltese, A.; Capodici, F.; Ciraolo, G.; La Loggia, G.; Rallo, G.

    2013-10-01

    An operational use of the actual evapotranspiration estimates requires the integration from instantaneous to daily values. This can commonly be achieved under the hypothesis of daytime self-preservation of the evaporative fraction. In this study, it has been evaluated the effect of this assumption on the assessment of daily evapotranspiration from proximity sensing images acquired at hourly intervals over a homogeneous olive groove. Results have been validated by comparison with observations made by a micrometeorological (EC-flux tower) and an eco-physiological (sap flux) sensor. SEBAL model has been applied to thermal and multispectral images acquired during a clear day on August 2009 trough a FLIR A320G thermal camera and a Tetracam MCA II multispectral camera, installed on a tethered helium balloon. Thermal and multispectral images were characterized by very high spatial resolution. This experiment aims to analyze two effects: 1) the consistency of the self-preservation hypothesis for daily estimates of the actual evapotranspiration from hourly assessments at different times of the day; 2) the effects of the spatial resolution on the performances of the energy balance model. To evaluate the effects of the spatial resolution, semi-hourly observations made by a flux tower and sap-flow measures were compared to the evapotranspiration estimates performed using downscaled images at resolutions close to canopy sizes (2, 5 and 10 m). Results show that the best estimates are obtained with a spatial resolution comparable to the average size of the canopy with images taken approximately at 10 UTC.

  11. An Analysis of the Actual Processes of Physicists' Research and the Implications for Teaching Scientific Inquiry in School

    ERIC Educational Resources Information Center

    Park, Jongwon; Jang, Kyoung-Ae; Kim, Ikgyun

    2009-01-01

    Investigation of scientists' actual processes of conducting research can provide us with more realistic aspects of scientific inquiry. This study was performed to identify three aspects of scientists' actual research: their motivations for scientific inquiry, the scientific inquiry skills they used, and the main types of results obtained from…

  12. Thermal Protection System Cavity Heating for Simplified and Actual Geometries Using Computational Fluid Dynamics Simulations with Unstructured Grids

    NASA Technical Reports Server (NTRS)

    McCloud, Peter L.

    2010-01-01

    Thermal Protection System (TPS) Cavity Heating is predicted using Computational Fluid Dynamics (CFD) on unstructured grids for both simplified cavities and actual cavity geometries. Validation was performed using comparisons to wind tunnel experimental results and CFD predictions using structured grids. Full-scale predictions were made for simplified and actual geometry configurations on the Space Shuttle Orbiter in a mission support timeframe.

  13. Initial Results Using a Depolarization and Backscatter Unattended Lidar (DABUL2) System Operating at the University of Maryland Baltimore County (UMBC)

    NASA Astrophysics Data System (ADS)

    Berkoff, T.; Rogers, R.; McCann, K.; Evans, K.; McMillan, W.; Hoff, R.; Alvarez, R.; Richter, R.; Intrieri, J.; Eberhard, W.

    2006-05-01

    In early 2005, the University of Maryland at Baltimore County Atmospheric Physics Group (http://alg.umbc.edu) took possession of a Depolarization and Backscatter Unattended Lidar (DABUL2) system. This instrument is the second version of this style lidar developed by National Oceanic and Atmospheric Administration (NOAA) Earth System Research Laboratory (ESRL). Over the past 10 years, the original NOAA DABUL lidar has collected data from a variety of locations all over the world from the Western Pacific tropics to the Arctic Ocean. This type of system is capable of continuous, unattended profiling of cloud and aerosol layers throughout the troposphere and into the lower stratosphere. The DABUL2 lidar consists of a pulsed laser source emitting at a wavelength of 532 nm, that is expanded to a 35 cm diameter beam before exiting the instrument. The large diameter beam maximizes eye-safety, resulting in a power density less than commercially available laser pointers and making the system more practical for unattended operations. Adequate signal-to-noise performance is achieved using a receiver with a narrow field- of-view (FOV), 0.4 nm bandpass filtering, and a high laser pulse repetition rate (2 kHz) to maximize signal averaging for a given time interval. Backscatter polarization properties are obtained by pulse-to-pulse alternating the polarization state of the outgoing laser beam with a Pockels cell and synchronously detecting the range-gated backscatter intensity from the atmosphere. The first measurements obtained at UMBC with the DABUL2 system occurred during spring of 2005. Data were recorded over several days during a variety of cloud and no-cloud conditions, both during day and nighttime background levels. Time coincident lidar data were also compared to a Micro-Pulse Lidar (MPL) system operating 40 km to the southwest, at the NASA Goddard Space Flight Center. The MPL system did not have depolarization capability, but provided elastic scattering measurements

  14. Wide Angle Imaging Lidar (WAIL): Theory of Operation and Results from Cross-Platform Validation at the ARM Southern Great Plains Site

    NASA Astrophysics Data System (ADS)

    Polonsky, I. N.; Davis, A. B.; Love, S. P.

    2004-05-01

    WAIL was designed to determine physical and geometrical characteristics of optically thick clouds using the off-beam component of the lidar return that can be accurately modeled within the 3D photon diffusion approximation. The theory shows that the WAIL signal depends not only on the cloud optical characteristics (phase function, extinction and scattering coefficients) but also on the outer thickness of the cloud layer. This makes it possible to estimate the mean optical and geometrical thicknesses of the cloud. The comparison with Monte Carlo simulation demonstrates the high accuracy of the diffusion approximation for moderately to very dense clouds. During operation WAIL is able to collect a complete data set from a cloud every few minutes, with averaging over horizontal scale of a kilometer or so. In order to validate WAIL's ability to deliver cloud properties, the LANL instrument was deployed as a part of the THickness from Off-beam Returns (THOR) validation IOP. The goal was to probe clouds above the SGP CART site at night in March 2002 from below (WAIL and ARM instruments) and from NASA's P3 aircraft (carrying THOR, the GSFC counterpart of WAIL) flying above the clouds. The permanent cloud instruments we used to compare with the results obtained from WAIL were ARM's laser ceilometer, micro-pulse lidar (MPL), millimeter-wavelength cloud radar (MMCR), and micro-wave radiometer (MWR). The comparison shows that, in spite of an unusually low cloud ceiling, an unfavorable observation condition for WAIL's present configuration, cloud properties obtained from the new instrument are in good agreement with their counterparts obtained by other instruments. So WAIL can duplicate, at least for single-layer clouds, the cloud products of the MWR and MMCR together. But WAIL does this with green laser light, which is far more representative than microwaves of photon transport processes at work in the climate system.

  15. Estimation of Regional-Scale Actual Evapotranspiration in Okayama prefecture in Japan using Complementary Relationship

    NASA Astrophysics Data System (ADS)

    Moroizumi, T.; Yamamoto, M.; Miura, T.

    2008-12-01

    It is important to estimate accurately a water balance in watershed for proposing a reuse of water resources and a proper settlement of water utilization. Evapotranspiration (ET) is an important factor of water balance. Therefore, it is needed to estimate accurately the actual ET. The objective of this study is to estimate accurately monthly actual ET in Yoshii, Asahi, and Takahashi River watersheds in Okayama prefecture from 1999 to 2000. The monthly actual ET was calculated by a Morton and a modified Brutsaert and Stricker (B&S) method, using Automated Meteorological Data Acquisition Systems (AMeDAS) in the basin. The actual ET was estimated using land covers which were classified in 11 categories. The land covers includes the effects of albedo. The actual ET was related to the elevation at each AMeDAS station. Using this relationship, the actual ET at the 1 or 5 km grid-interval mesh in the basin was calculated, and finally, the distribution of actual ET was mapped. The monthly ET estimated by the modified B&S method were smaller than that by Morton method which showed a same tendency as the Penman potential ET (PET). The annual values of Morton"fs ET, modified B&S"fs ET, and PET were estimated as 796, 645, and 800 mm, respectively. The ET by the modified B&S was larger in hilly and mountainous areas than in settlement or city. In general, it was a reasonable result because city or settlement areas were covered with concrete and asphalt and the ET was controlled.

  16. Establishing seasonal chronicles of actual evapotranspiration under sloping conditions

    NASA Astrophysics Data System (ADS)

    Zitouna Chebbi, R.; Prévot, L.; Jacob, F.; Voltz, M.

    2012-04-01

    Estimation of daily and seasonal actual evapotranspiration (ETa) is strongly needed for hydrological and agricultural purposes. Although the eddy covariance method is well suited for such estimation of land surface fluxes, this method suffers from limitations when establishing long time series. Missing data are often encountered, resulting from bad meteorological conditions, rejection by quality control tests, power failures… Numerous gap fill techniques have been proposed in the literature but there applicability in sloping conditions is not well known. In order to estimate ETa over long periods (agricultural cycle) on crops cultivated in sloping areas, a pluri-annual experiment was conducted in the Kamech catchment, located in North-eastern Tunisia. This Mediterranean site is characterized by a large heterogeneity in topography, soils and crops. Land surface fluxes were measured using eddy covariance systems. Measurements were collected on the two opposite sides of the Kamech V-shaped catchment, within small fields having slopes steeper than 5%. During three different years, four crops were studied: durum wheat, oat, fava bean and pasture. The topography of the catchment and the wind regime induced upslope and downslope flows over the study fields. In this study, we showed that gap filling of the turbulent fluxes (sensible and latent heat) can be obtained through linear regressions against net radiation. To account for the effect of the topography, linear regressions were calibrated by distinguishing upslope and downslope flows. This significantly improved the quality of the reconstructed data over 30 minute intervals. This gap filling technique also improved the energy balance closure at the daily time scale. As a result, seasonal chronicles of daily ETa throughout the growth cycle of the study crops in the Kamech watershed were established, thus providing useful information about the water use of annual crops in a semi-arid rainfed and hilly area.

  17. Experimental investigation of panel radiator heat output enhancement for efficient thermal use under actual operating conditions

    NASA Astrophysics Data System (ADS)

    Calisir, Tamer; Baskaya, Senol; Onur Yazar, Hakan; Yucedag, Sinan

    2015-05-01

    In this study the heat output of a panel-convector-convector-panel radiator (PCCP) under controlled laboratory conditions under Turkish household and especially Ankara conditions was investigated experimentally. In this sense, investigations were performed for different heating water mass flow rates, water inlet temperatures and radiator inlet and outlet connection positions, which are most commonly used in Turkey. An experimental setup was built for this purpose in a test room where temperature was controlled and held constant during the experiments. Inlet and outlet water temperatures and mass flow rates were measured and heat output of the radiator was calculated. Infrared thermal camera visualizations of the steel panel radiator front surface were also performed.

  18. Task Technical and Quality Assurance Plan for Determining Uranium and Plutonium Solubility in Actual Tank Waste Supernates

    SciTech Connect

    King, William D.

    2005-06-28

    Savannah River Site tank waste supernates contain small quantities of dissolved uranium and plutonium. Due to the large volume of supernates, significant quantities of dissolved uranium and plutonium are managed as part of waste transfers, evaporation and pretreatment at the Savannah River Site in tank farm operations, the Actinide Removal Project (ARP), and the Salt Waste Processing Facility (SWPF). Previous SRNL studies have investigated the effect of temperature and major supernate components on the solubility of uranium and plutonium. Based on these studies, equations were developed for the prediction of U and Pu solubility in tank waste supernates. The majority of the previous tests were conducted with simulated waste solutions. The current testing is intended to determine solubility in actual tank waste samples (as-received, diluted, and combinations of tank samples) as a function of composition and temperature. Results will be used to validate and build on the existing solubility equations.

  19. Sustainable Power Generation in Continuous Flow Microbial Fuel Cell Treating Actual Wastewater: Influence of Biocatalyst Type on Electricity Production

    PubMed Central

    Ismail, Zainab Z.; Jaeel, Ali Jwied

    2013-01-01

    Microbial fuel cells (MFCs) have the potential to simultaneously treat wastewater for reuse and to generate electricity. This study mainly considers the performance of an upflow dual-chambered MFC continuously fueled with actual domestic wastewater and alternatively biocatalyzed with aerobic activated sludge and strain of Bacillus Subtilis. The behavior of MFCs during initial biofilm growth and characterization of anodic biofilm were studied. After 45 days of continuous operation, the biofilms on the anodic electrode were well developed. The performance of MFCs was mainly evaluated in terms of COD reductions and electrical power output. Results revealed that the COD removal efficiency was 84% and 90% and the stabilized power outputs were clearly observed achieving a maximum value of 120 and 270 mW/m2 obtained for MFCs inoculated with mixed cultures and Bacillus Subtilis strain, respectively. PMID:24453893

  20. Innovation Teams: Operating Principles.

    ERIC Educational Resources Information Center

    Thomas, George B.; Jones, James M.

    This examination of the operation of teams in the Pilot Communities Program is chiefly historical in character. Based on intensive examination of proposals, evaluation studies, reports, memoranda, and interviews with personnel involved in the program, it was written by two university professors who had not been involved in the actual program. The…

  1. A Flawed Argument Against Actual Infinity in Physics

    NASA Astrophysics Data System (ADS)

    Perez Laraudogoitia, Jon

    2010-12-01

    In “Nonconservation of Energy and loss of Determinism II. Colliding with an Open Set” (2010) Atkinson and Johnson argue in favour of the idea that an actual infinity should be excluded from physics, at least in the sense that physical systems involving an actual infinity of component elements should not be admitted. In this paper I show that the argument Atkinson and Johnson use is erroneous and that an analysis of the situation considered by them is possible without requiring any type of rejection of the idea of infinity.

  2. Treatability studies of actual listed waste sludges from the Oak Ridge Reservation (ORR)

    SciTech Connect

    Jantzen, C.M.; Peeler, D.K.; Gilliam, T.M.; Bleier, A.; Spence, R.D.

    1996-05-06

    Oak Ridge National Laboratory (ORNL) and Savannah River Technology Center (SRTC) are investigating vitrification for various low-level and mixed wastes on the Oak Ridge Reservation (ORR). Treatability studies have included surrogate waste formulations at the laboratory-, pilot-, and field-scales and actual waste testing at the laboratory- and pilot-scales. The initial waste to be processing through SRTC`s Transportable Vitrification System (TVS) is the K-1407-B and K-1407-C (B/C) Pond sludge waste which is a RCRA F-listed waste. The B/C ponds at the ORR K-25 site were used as holding and settling ponds for various waste water treatment streams. Laboratory-, pilot-, and field- scale ``proof-of-principle`` demonstrations are providing needed operating parameters for the planned field-scale demonstration with actual B/C Pond sludge waste at ORR. This report discusses the applied systems approach to optimize glass compositions for this particular waste stream through laboratory-, pilot-, and field-scale studies with surrogate and actual B/C waste. These glass compositions will maximize glass durability and waste loading while optimizing melt properties which affect melter operation, such as melt viscosity and melter refractory corrosion. Maximum waste loadings minimize storage volume of the final waste form translating into considerable cost savings.

  3. Operator interface for vehicles

    DOEpatents

    Bissontz, Jay E

    2015-03-10

    A control interface for drivetrain braking provided by a regenerative brake and a non-regenerative brake is implemented using a combination of switches and graphic interface elements. The control interface comprises a control system for allocating drivetrain braking effort between the regenerative brake and the non-regenerative brake, a first operator actuated control for enabling operation of the drivetrain braking, and a second operator actuated control for selecting a target braking effort for drivetrain braking. A graphic display displays to an operator the selected target braking effort and can be used to further display actual braking effort achieved by drivetrain braking.

  4. Are presolar dust grains from novae actually from supernovae?

    NASA Astrophysics Data System (ADS)

    Nittler, L. R.; Hoppe, P.

    2005-05-01

    Meteorites contain presolar stardust grains that formed in prior generations of stars and exhibit large isotopic anomalies reflecting the nuclear processes that occurred in their individual parent stars. RGB and AGB stars and supernovae are well established as sources of many of these grains. Novae have been proposed as sources for a few SiC and graphite grains with low 12}C/{13C and 14}N/{15N ratios and unusual Si isotopic ratios (Amari et al., ApJ, 551, 1065). We have found three SiC grains from the Murchison meteorite with C and N isotopic ratios similar to the previously-reported putative nova grains. However, the isotopic signatures of Si, Ca, Al and Ti in one of the grains (334-2) clearly indicate a supernova origin, especially excess 28Si correlated with excess 44Ca. The latter signature is attributable to in situ decay of (half-life=50yr) 44Ti. Another 13C- and 15N-rich grain (151-4) has a large 47Ti enrichment. This signature is not expected for nova nucleosynthesis. Thus, the new isotopic data raise the possibility that the grains previously reported to have formed in novae actually formed in supernovae, and that novae have not left a record in the presolar grain populations that have been so far studied. Moreover, the results in grain 334-2 indicate that supernovae contain regions highly enriched in both 13C and 15N. This is not predicted by current models but may bear on the cosmic origin of 15N. This work was funded in part by NASA.

  5. Beaked Whales Respond to Simulated and Actual Navy Sonar

    PubMed Central

    Tyack, Peter L.; Zimmer, Walter M. X.; Moretti, David; Southall, Brandon L.; Claridge, Diane E.; Durban, John W.; Clark, Christopher W.; D'Amico, Angela; DiMarzio, Nancy; Jarvis, Susan; McCarthy, Elena; Morrissey, Ronald; Ward, Jessica; Boyd, Ian L.

    2011-01-01

    Beaked whales have mass stranded during some naval sonar exercises, but the cause is unknown. They are difficult to sight but can reliably be detected by listening for echolocation clicks produced during deep foraging dives. Listening for these clicks, we documented Blainville's beaked whales, Mesoplodon densirostris, in a naval underwater range where sonars are in regular use near Andros Island, Bahamas. An array of bottom-mounted hydrophones can detect beaked whales when they click anywhere within the range. We used two complementary methods to investigate behavioral responses of beaked whales to sonar: an opportunistic approach that monitored whale responses to multi-day naval exercises involving tactical mid-frequency sonars, and an experimental approach using playbacks of simulated sonar and control sounds to whales tagged with a device that records sound, movement, and orientation. Here we show that in both exposure conditions beaked whales stopped echolocating during deep foraging dives and moved away. During actual sonar exercises, beaked whales were primarily detected near the periphery of the range, on average 16 km away from the sonar transmissions. Once the exercise stopped, beaked whales gradually filled in the center of the range over 2–3 days. A satellite tagged whale moved outside the range during an exercise, returning over 2–3 days post-exercise. The experimental approach used tags to measure acoustic exposure and behavioral reactions of beaked whales to one controlled exposure each of simulated military sonar, killer whale calls, and band-limited noise. The beaked whales reacted to these three sound playbacks at sound pressure levels below 142 dB re 1 µPa by stopping echolocation followed by unusually long and slow ascents from their foraging dives. The combined results indicate similar disruption of foraging behavior and avoidance by beaked whales in the two different contexts, at exposures well below those used by regulators to define

  6. Comparison of Projections to Actual Performance in the DOE-EPRI Wind Turbine Verification Program

    SciTech Connect

    Rhoads, H.; VandenBosche, J.; McCoy, T.; Compton, A.; Smith, B.

    2000-09-11

    As part of the US Department of Energy/Electric Power Research Institute (DOE-EPRI) Wind Turbine Verification Program (TVP), Global Energy Concepts (GEC) worked with participating utilities to develop a set of performance projections for their projects based on historical site atmospheric conditions, turbine performance data, operation and maintenance (O and M) strategies, and assumptions about various energy losses. After a preliminary operation period at each project, GEC compared the actual performance to projections and evaluated the accuracy of the data and assumptions that formed the performance projections. This paper presents a comparison of 1999 power output, turbine availability, and other performance characteristics to the projections for TVP projects in Texas, Vermont, Iowa, Nebraska, Wisconsin, and Alaska. Factors that were overestimated or underestimated are quantified. Actual wind speeds are compared to projections based on long-term historical measurements. Turbine power curve measurements are compared with data provided by the manufacturers, and loss assumptions are evaluated for accuracy. Overall, the projects performed well, particularly new commercial turbines in the first few years of operation. However, some sites experienced below average wind resources and greater than expected losses. The TVP project owners successfully developed and constructed wind power plants that are now in full commercial operation, serving a total of approximately 12,000 households.

  7. 14 CFR 380.33a - Operator's option plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... of the actual dates or cities is at the charter operator's option. (e) Charter operators and their... operator's option plan contracts of the actual dates or cities, as applicable, as required by contracts. ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Operator's option plan. 380.33a Section...

  8. Actualizing Concepts in Home Management: Proceedings of a National Conference.

    ERIC Educational Resources Information Center

    American Home Economics Association, Washington, DC.

    The booklet prints the following papers delivered at a national conference: Actualizing Concepts in Home Management: Decision Making, Dorothy Z. Price; Innovations in Teaching: Ergonomics, Fern E. Hunt; Relevant Concepts of Home Management: Innovations in Teaching, Kay P. Edwards; Standards in a Managerial Context, Florence S. Walker; Organizing:…

  9. 26 CFR 513.8 - Addressee not actual owner.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... CONVENTIONS IRELAND Withholding of Tax § 513.8 Addressee not actual owner. (a) If any person with an address in Ireland who receives a dividend from a United States corporation with respect to which United... such reduced rate of 15 percent, such recipient in Ireland will withhold an additional amount of...

  10. Remote sensing estimates of actual evapotranspiration in an irrigation district

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Accurate estimates of the spatial distribution of actual evapotranspiration (AET) are useful in hydrology, but can be difficult to obtain. Remote sensing provides a potential capability for routinely monitoring AET by combining remotely sensed surface temperature and vegetation cover observations w...

  11. Self Actualization of Females in an Experimental Orientation Program

    ERIC Educational Resources Information Center

    Vander Wilt, Robert B.; Klocke, Ronald A.

    1971-01-01

    An alternative to the traditional orientation program was developed that forced students to consider their physical and psychological outer limits. Students were confronted in a new and unique way that contributed to the self actualization process of the female portion of the group. (Author/BY)

  12. Actual Leisure Participation of Norwegian Adolescents with Down Syndrome

    ERIC Educational Resources Information Center

    Dolva, Anne-Stine; Kleiven, Jo; Kollstad, Marit

    2014-01-01

    This article reports the actual participation in leisure activities by a sample of Norwegian adolescents with Down syndrome aged 14. Representing a first generation to grow up in a relatively inclusive context, they live with their families, attend mainstream schools, and are part of common community life. Leisure information was obtained in…

  13. Research into Students' Perceptions of Preferred and Actual Learning Environment.

    ERIC Educational Resources Information Center

    Hattie, John A.; And Others

    Measures of both preferred and actual classroom and school environment were administered to 1,675 secondary school students in New South Wales (Australia). Shortened versions of the My Class Inventory, Classroom Environment Scale, and Individualized Classroom Environment Questionnaire, as well as the Quality of School Life questionnaire were…

  14. MLCMS Actual Use, Perceived Use, and Experiences of Use

    ERIC Educational Resources Information Center

    Asiimwe, Edgar Napoleon; Grönlund, Åke

    2015-01-01

    Mobile learning involves use of mobile devices to participate in learning activities. Most e-learning activities are available to participants through learning systems such as learning content management systems (LCMS). Due to certain challenges, LCMS are not equally accessible on all mobile devices. This study investigates actual use, perceived…

  15. 40 CFR 74.22 - Actual SO2 emissions rate.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....6 for natural gas For other fuels, the combustion source must specify the SO2 emissions factor. (c... (CONTINUED) SULFUR DIOXIDE OPT-INS Allowance Calculations for Combustion Sources § 74.22 Actual SO2 emissions rate. (a) Data requirements. The designated representative of a combustion source shall submit...

  16. Progressive Digressions: Home Schooling for Self-Actualization.

    ERIC Educational Resources Information Center

    Rivero, Lisa

    2002-01-01

    Maslow's (1971) theory of primary creativeness is used as the basis for a self-actualization model of education. Examples of how to use the model in creative homeschooling are provided. Key elements include digressive and immersion learning, self-directed learning, and the integration of work and play. Teaching suggestions are provided. (Contains…

  17. A Taxometric Analysis of Actual Internet Sports Gambling Behavior

    ERIC Educational Resources Information Center

    Braverman, Julia; LaBrie, Richard A.; Shaffer, Howard J.

    2011-01-01

    This article presents findings from the first taxometric study of actual gambling behavior to determine whether we can represent the characteristics of extreme gambling as qualitatively distinct (i.e., taxonic) or as a point along a dimension. We analyzed the bets made during a 24-month study period by the 4,595 most involved gamblers among a…

  18. Influence of System Operation Method on CO2 Emissions of PV/Solar Heat/Cogeneration System

    NASA Astrophysics Data System (ADS)

    Oke, Shinichiro; Kemmoku, Yoshishige; Takikawa, Hirofumi; Sakakibara, Tateki

    A PV/solar heat/cogeneration system is assumed to be installed in a hotel. The system is operated with various operation methods: CO2 minimum operation, fees minimum operation, seasonal operation, daytime operation and heat demand following operation. Of these five operations, the former two are virtual operations that are operated with the dynamic programming method, and the latter three are actual operations. Computer simulation is implemented using hourly data of solar radiation intensity, atmospheric temperature, electric, cooling, heating and hot water supply demands for one year, and the life-cycle CO2 emission and the total cost are calculated for every operations. The calculation results show that the virtual two and the actual three operations reduce the life-cycle CO2 emission by 21% and 13% compared with the conventional system, respectively. In regard to both the CO2 emission and the cost, there is no significant difference between the virtual two operation methods or among actual three operation methods.

  19. Resolving Off-Nominal Situations in Schedule-Based Terminal Area Operations: Results from a Human-in-the-Loop Simulation

    NASA Technical Reports Server (NTRS)

    Mercer, Joey; Callantine, Todd; Martin, Lynne

    2012-01-01

    A recent human-in-the-loop simulation in the Airspace Operations Laboratory (AOL) at NASA's Ames Research Center investigated the robustness of Controller-Managed Spacing (CMS) operations. CMS refers to AOL-developed controller tools and procedures for enabling arrivals to conduct efficient Optimized Profile Descents with sustained high throughput. The simulation provided a rich data set for examining how a traffic management supervisor and terminal-area controller participants used the CMS tools and coordinated to respond to off-nominal events. This paper proposes quantitative measures for characterizing the participants responses. Case studies of go-around events, replicated during the simulation, provide insights into the strategies employed and the role the CMS tools played in supporting them.

  20. Operating experience with the natural bridges national monument photovoltaic power system

    SciTech Connect

    Solman, F. J.; Grossman, B. L.

    1981-01-01

    The 100-kW photovoltaic power system at Natural Bridges National Monument in southwestern Utah has been in operation since May 1980. A comparison of system simulation with actual operation has been performed, good agreement has been found, and results are presented. In addition, conservation measures and their benefits are described. Operating experience with the system is presented, including measured component performance of the arrays, batteries, inverters, and system overhead loads.

  1. Do Open Geodata Actually have the Quality they Declare? the Case Study of Milan, Italy

    NASA Astrophysics Data System (ADS)

    Brovelli, M. A.; Minghini, M.; Molinari, M. E.; Molteni, M.

    2016-06-01

    In the past number of years there has been an amazing flourishing of spatial data products released with open licenses. Researchers and professionals are extensively exploiting open geodata for many applications, which, in turn, include decision-making results and other (derived) geospatial datasets among their outputs. Despite the traditional availability of metadata, a question arises about the actual quality of open geodata, as their declared quality is typically given for granted without any systematic assessment. The present work investigates the case study of Milan Municipality (Northern Italy). A wide set of open geodata are available for this area which are released by national, regional and local authoritative entities. A comprehensive cataloguing operation is first performed, with 1061 geospatial open datasets from Italian providers found which highly differ in terms of license, format, scale, content, and release date. Among the many quality parameters for geospatial data, the work focuses on positional accuracy. An example of positional accuracy assessment is described for an openly-licensed orthophoto through comparison with the official, up-to-date, and large-scale vector cartography of Milan. The comparison is run according to the guidelines provided by ISO and shows that the positional accuracy declared by the orthophoto provider does not correspond to the reality. Similar results are found from analyses on other datasets (not presented here). Implications are twofold: raising the awareness on the risks of using open geodata by taking their quality for granted; and highlighting the need for open geodata providers to introduce or refine mechanisms for data quality control.

  2. Removal efficiency of pharmaceuticals and personal care products with varying wastewater treatment processes and operating conditions - conception of a database and first results.

    PubMed

    Miège, C; Choubert, J M; Ribeiro, L; Eusèbe, M; Coquery, M

    2008-01-01

    We created a database in order to quantitatively assess the occurrence and removal efficiency of PPCPs in WWTPs. From 113 scientific publications, we compiled 5887 data on the concentrations and loads of PPCPs in WWTP influents and effluents, and on their removal efficiency. The first outputs of our database include: (1) a list of the most frequently studied molecules, their frequency of detection, their mean concentration and removal in liquid influent and effluent; (2) a comparison of the removal efficiency for different WWTP processes; (3) a study of the influence of the operating conditions (sludge and hydraulic retention times). PMID:18192740

  3. Testing two temporal upscaling schemes for the estimation of the time variability of the actual evapotranspiration

    NASA Astrophysics Data System (ADS)

    Maltese, A.; Capodici, F.; Ciraolo, G.; La Loggia, G.

    2015-10-01

    Temporal availability of grapes actual evapotranspiration is an emerging issue since vineyards farms are more and more converted from rainfed to irrigated agricultural systems. The manuscript aims to verify the accuracy of the actual evapotranspiration retrieval coupling a single source energy balance approach and two different temporal upscaling schemes. The first scheme tests the temporal upscaling of the main input variables, namely the NDVI, albedo and LST; the second scheme tests the temporal upscaling of the energy balance output, the actual evapotranspiration. The temporal upscaling schemes were implemented on: i) airborne remote sensing data acquired monthly during a whole irrigation season over a Sicilian vineyard; ii) low resolution MODIS products released daily or weekly; iii) meteorological data acquired by standard gauge stations. Daily MODIS LST products (MOD11A1) were disaggregated using the DisTrad model, 8-days black and white sky albedo products (MCD43A) allowed modeling the total albedo, and 8-days NDVI products (MOD13Q1) were modeled using the Fisher approach. Results were validated both in time and space. The temporal validation was carried out using the actual evapotranspiration measured in situ using data collected by a flux tower through the eddy covariance technique. The spatial validation involved airborne images acquired at different times from June to September 2008. Results aim to test whether the upscaling of the energy balance input or output data performed better.

  4. Using Quasi-Horizontal Alignment in the absence of the actual alignment.

    PubMed

    Banihashemi, Mohamadreza

    2016-10-01

    Horizontal alignment is a major roadway characteristic used in safety and operational evaluations of many facility types. The Highway Safety Manual (HSM) uses this characteristic in crash prediction models for rural two-lane highways, freeway segments, and freeway ramps/C-D roads. Traffic simulation models use this characteristic in their processes on almost all types of facilities. However, a good portion of roadway databases do not include horizontal alignment data; instead, many contain point coordinate data along the roadways. SHRP 2 Roadway Information Database (RID) is a good example of this type of data. Only about 5% of this geodatabase contains alignment information and for the rest, point data can easily be produced. Even though the point data can be used to extract actual horizontal alignment data but, extracting horizontal alignment is a cumbersome and costly process, especially for a database of miles and miles of highways. This research introduces a so called "Quasi-Horizontal Alignment" that can be produced easily and automatically from point coordinate data and can be used in the safety and operational evaluations of highways. SHRP 2 RID for rural two-lane highways in Washington State is used in this study. This paper presents a process through which Quasi-Horizontal Alignments are produced from point coordinates along highways by using spreadsheet software such as MS EXCEL. It is shown that the safety and operational evaluations of the highways with Quasi-Horizontal Alignments are almost identical to the ones with the actual alignments. In the absence of actual alignment the Quasi-Horizontal Alignment can easily be produced from any type of databases that contain highway coordinates such geodatabases and digital maps. PMID:27391796

  5. FRACTIONAL CRYSTALLIZATION FLOWSHEET TESTS WITH ACTUAL TANK WASTE

    SciTech Connect

    HERTING, D.L.

    2006-10-18

    Laboratory-scale flowsheet tests of the fractional crystallization process were conducted with actual tank waste samples in a hot cell at the 222-S Laboratory. The process is designed to separate medium-curie liquid waste into a low-curie stream for feeding to supplemental treatment and a high-curie stream for double-shell tank storage. Separations criteria (for Cs-137 sulfate, and sodium) were exceeded in all three of the flowsheet tests that were performed.

  6. FRACTIONAL CRYSTALLIZATION FLOWSHEET TESTS WITH ACTUAL TANK WASTE

    SciTech Connect

    HERTING, D.L.

    2007-04-13

    Laboratory-scale flowsheet tests of the fractional crystallization process were conducted with actual tank waste samples in a hot cell at the 2224 Laboratory. The process is designed to separate medium-curie liquid waste into a low-curie stream for feeding to supplemental treatment and a high-curie stream for double-shell tank storage. Separations criteria (for Cesium-137 sulfate and sodium) were exceeded in all three of the flowsheet tests that were performed.

  7. 63. VIEW OF AUTOTRANSFERS. THE ACTUAL AUTOTRANSFERS ARE ENCLOSED IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    63. VIEW OF AUTOTRANSFERS. THE ACTUAL AUTOTRANSFERS ARE ENCLOSED IN THE OIL FILLED CYLINDERS ON THE RIGHT OF THE PHOTOGRAPH. THESE ELECTRICAL DEVICES BOOSTED THE GENERATOR OUTPUT OF 11,000 VOLTS TO 22,000 VOLTS PRIOR TO TRANSMISSION OUT TO THE MAIN FEEDER LINES. A SPARE INNER UNIT IS CONTAINED IN THE METAL BOX AT THE LEFT OF THE PHOTOGRAPH. - New York, New Haven & Hartford Railroad, Cos Cob Power Plant, Sound Shore Drive, Greenwich, Fairfield County, CT

  8. Perceived accessibility versus actual physical accessibility of healthcare facilities.

    PubMed

    Sanchez, J; Byfield, G; Brown, T T; LaFavor, K; Murphy, D; Laud, P

    2000-01-01

    This study addressed how healthcare clinics perceive themselves in regard to accessibility for persons with spinal cord injuries (SCI). All 40 of the clinics surveyed reported that they were wheelchair accessible; however, there was significant variability in the number of sites that actually met the guidelines of the Americans with Disability Act. In general, a person using a wheelchair could enter the building, the examination room, and the bathroom. The majority of sites did not have an examination table that could be lowered to wheelchair level. Most reported limited experience in working with persons with (SCI), yet they claimed to be able to assist with difficult transfers. Only one site knew about autonomic dysreflexia. Problems of accessibility appeared to be seriously compounded by the clinics' perception of how they met physical accessibility guidelines without consideration of the actual needs of persons with SCI. This study addressed the perception of accessibility as reported by clinic managers versus actual accessibility in healthcare clinics in a Midwestern metropolitan area for persons using wheelchairs. PMID:10754921

  9. The actual citation impact of European oncological research.

    PubMed

    López-Illescas, Carmen; de Moya-Anegón, Félix; Moed, Henk F

    2008-01-01

    This study provides an overview of the research performance of major European countries in the field Oncology, the most important journals in which they published their research articles, and the most important academic institutions publishing them. The analysis was based on Thomson Scientific's Web of Science (WoS) and calculated bibliometric indicators of publication activity and actual citation impact. Studying the time period 2000-2006, it gives an update of earlier studies, but at the same time it expands their methodologies, using a broader definition of the field, calculating indicators of actual citation impact, and analysing new and policy relevant aspects. Findings suggest that the emergence of Asian countries in the field Oncology has displaced European articles more strongly than articles from the USA; that oncologists who have published their articles in important, more general journals or in journals covering other specialties, rather than in their own specialist journals, have generated a relatively high actual citation impact; and that universities from Germany, and--to a lesser extent--those from Italy, the Netherlands, UK, and Sweden, dominate a ranking of European universities based on number of articles in oncology. The outcomes illustrate that different bibliometric methodologies may lead to different outcomes, and that outcomes should be interpreted with care. PMID:18039565

  10. Positioning the actual interference fringe pattern on the tooth flank in measuring gear tooth flanks by laser interferometry

    NASA Astrophysics Data System (ADS)

    Fang, Suping; Wang, Leijie; Liu, Shiqiao; Komori, Masaharu; Kubo, Aizoh

    2011-05-01

    In measuring form deviation of gear tooth flanks by laser interferometry, the collected interference fringe pattern (IFP) is badly distorted, in the case of shape, relative to the actual tooth flank. Meanwhile, a clear and definite mapping relationship between the collected IFP and the actual tooth flank is indispensable for both transforming phase differences into deviation values and positioning the measurement result on the actual tooth flank. In order to solve these problems, this paper proposes a method using the simulation tooth image as a bridge connecting the actual tooth flank and the collected IFP. The mapping relationship between the simulation tooth image and the actual tooth flank has been obtained by ray tracing methods [Fang et al., Appl. Opt. 49(33), 6409-6415 (2010)]. This paper mainly discusses how to build the relationship between the simulation tooth image and the collected IFP by using a matching algorithm of two characteristic point sets. With the combination of the two above-mentioned assistant mapping relationships, the mapping relationship between the collected IFP and the actual tooth flank can be built; the collected IFP can be positioned on the actual tooth flank. Finally, the proposed method is employed in a measurement of the form deviation of a gear tooth flank and the result proves the feasibility of the proposed method.

  11. Designers' and users' roles in participatory design: What is actually co-designed by participants?

    PubMed

    Barcellini, Flore; Prost, Lorène; Cerf, Marianne

    2015-09-01

    This research deals with an analysis of forms of participation in a participatory design (PD) process of a software that assesses the sustainability of agricultural cropping systems. We explore the actual forms of participation of designers and users by adapting an Actual Role Analysis in Design approach (Barcellini et al., 2013) to capture the levels of abstraction (conceptual, functional and operational) of participants' discussions. We show that: (1) the process does not only concern the design of the artifact itself, but also the design of the concept of sustainability; (2) all participants (users & designers) have a role in co-designing the concept (in our case, sustainability); (3) some roles and profiles are key to this co-design. We discuss our contributions to both the research and the practices of participatory design. These contributions deal with the production of a method and related knowledge about actual activities in participatory design situations. They may support the development of relevant training programs regarding participatory situations, or be reflexive activities that can help those who are involved in designing and leading in participatory situations, to make improvements. PMID:25959315

  12. Laboratory stabilization/solidification of surrogate and actual mixed-waste sludge in glass and grout

    SciTech Connect

    Spence, R.D.; Gilliam, T.M.; Mattus, C.H.; Mattus, A.J.

    1998-03-03

    Grouting and vitrification are currently the most likely stabilization/solidification technologies for mixed wastes. Grouting has been used to stabilize and solidify hazardous and low-level waste for decades. Vitrification has long been developed as a high-level-waste alternative and has been under development recently as an alternative treatment technology for low-level mixed waste. Laboratory testing has been performed to develop grout and vitrification formulas for mixed-waste sludges currently stored in underground tanks at Oak Ridge National Laboratory (ORNL) and to compare these waste forms. Envelopes, or operating windows, for both grout and soda-lime-silica glass formulations for a surrogate sludge were developed. One formulation within each envelope was selected for testing the sensitivity of performance to variations ({+-}10 wt%) in the waste form composition and variations in the surrogate sludge composition over the range previously characterized in the sludges. In addition, one sludge sample of an actual mixed-waste tank was obtained, a surrogate was developed for this sludge sample, and grout and glass samples were prepared and tested in the laboratory using both surrogate and the actual sludge. The sensitivity testing of a surrogate tank sludge in selected glass and grout formulations is discussed in this paper, along with the hot-cell testing of an actual tank sludge sample.

  13. Urban rail transit projects: Forecast versus actual ridership and costs. Final report

    SciTech Connect

    Pickrell, D.H.

    1989-10-01

    Substantial errors in forecasting ridership and costs for the ten rail transit projects reviewed in the report put forth the possibility that more accurate forecasts would have led decision-makers to select projects other than those reviewed. The study examines the accuracy of forecasts prepared for ten major capital improvement projects in nine urban areas during 1971-1987. Each project includes construction of a fixed transit guideway: Rapid Rail or Metrorail (Washington DC, Atlanta, Baltimore, Miami); Light Rail Transit (Buffalo, Pittsburgh, Portland, Sacramento); and Downtown Peoplemover (Miami and Detroit). The study examines why actual costs and ridership differed so markedly from their forecast values. It focuses on the accuracy of projections made available to local decision-makers at the time when the choice among alternative projects was actually made. The study compares forecast and actual values for four types of measures: ridership, capital costs and financing, operating and maintenance costs, and cost-effectiveness. The report is organized into 6 chapters, numerous tables, and an appendix that documents the sources of all data appearing in the tables presented in the report.

  14. Blade-to-coolant heat-transfer results and operating data from a natural-convection water-cooled single-stage turbine

    NASA Technical Reports Server (NTRS)

    Diaguila, Anthony J; Freche, John C

    1951-01-01

    Blade-to-coolant heat-transfer data and operating data were obtained with a natural-convection water-cooled turbine over range of turbine speeds and inlet-gas temperatures. The convective coefficients were correlated by the general relation for natural-convection heat transfer. The turbine data were displaced from a theoretical equation for natural convection heat transfer in the turbulent region and from natural-convection data obtained with vertical cylinders and plates; possible disruption of natural convection circulation within the blade coolant passages was thus indicated. Comparison of non dimensional temperature-ratio parameters for the blade leading edge, midchord, and trailing edge indicated that the blade cooling effectiveness is greatest at the midchord and least at the trailing edge.

  15. Prediction of ground vibrations resulting from the blasting operations in an open-pit mine by adaptive neuro-fuzzy inference system

    NASA Astrophysics Data System (ADS)

    Iphar, Melih; Yavuz, Mahmut; Ak, Hakan

    2008-11-01

    The aim of this study is to predict the peak particle velocity (PPV) values from both presently constructed simple regression model and fuzzy-based model. For this purpose, vibrations induced by bench blasting operations were measured in an open-pit mine operated by the most important magnesite producing company (MAS) in Turkey. After gathering the ordered pairs of distance and PPV values, the site-specific parameters were determined using traditional regression method. Also, an attempt has been made to investigate the applicability of a relatively new soft computing method called as the adaptive neuro-fuzzy inference system (ANFIS) to predict PPV. To achieve this objective, data obtained from the blasting measurements were evaluated by constructing an ANFIS-based prediction model. The distance from the blasting site to the monitoring stations and the charge weight per delay were selected as the input parameters of the constructed model, the output parameter being the PPV. Valid for the site, the PPV prediction capability of the constructed ANFIS-based model has proved to be successful in terms of statistical performance indices such as variance account for (VAF), root mean square error (RMSE), standard error of estimation, and correlation between predicted and measured PPV values. Also, using these statistical performance indices, a prediction performance comparison has been made between the presently constructed ANFIS-based model and the classical regression-based prediction method, which has been widely used in the literature. Although the prediction performance of the regression-based model was high, the comparison has indicated that the proposed ANFIS-based model exhibited better prediction performance than the classical regression-based model.

  16. Consumer choice: Linking consumer intentions to actual purchase of GM labeled food products.

    PubMed

    Sleenhoff, Susanne; Osseweijer, Patricia

    2013-01-01

    With a mandatory labeling scheme for GM food in Europe since 2004 measuring actual consumer choice in practice has become possible. Anticipating Europeans negative attitude toward GM food, the labeling was enforced to allow consumers to make an informed choice. We studied consumers actual purchase behavior of GM food products and compared this with their attitude and behavioral intention for buying GM food. We found that despite a majority of consumers voicing a negative attitude toward GM food over 50% of our European respondents stated that they did not actively avoid the purchase of GM food and 6% actually purchased one of the few available GM labeled food products in the period between September 2006 and October 2007. Our results imply that a voiced negative attitude of consumers in responses to questionnaires about their intentions is not a reliable guide for what they actually do in supermarkets. We conclude that the assumption of a negative attitude with regard to GM food is at least in part construed. PMID:24051512

  17. Actual versus perceived peer sexual risk behavior in online youth social networks.

    PubMed

    Black, Sandra R; Schmiege, Sarah; Bull, Sheana

    2013-09-01

    Perception of peer behaviors is an important predictor of actual risk behaviors among youth. However, we lack understanding of peer influence through social media and of actual and perceived peer behavior concordance. The purpose of this research is to document the relationship between individual perception of and actual peer sexual risk behavior using online social networks. The data are a result of a secondary analysis of baseline self-reported and peer-reported sexual risk behavior from a cluster randomized trial including 1,029 persons from 162 virtual networks. Individuals (seeds) recruited up to three friends who then recruited additional friends, extending three waves from the seed. ANOVA models compared network means of actual participant behavior across categories of perceived behavior. Concordance varied between reported and perceived behavior, with higher concordance between perceived and reported condom use, multiple partners, concurrent partners, sexual pressure, and drug and alcohol use during sex. Individuals significantly over-reported risk and under-reported protective peer behaviors related to sex. PMID:24073183

  18. Generalized Weierstrass-Mandelbrot Function Model for Actual Stocks Markets Indexes with Nonlinear Characteristics

    NASA Astrophysics Data System (ADS)

    Zhang, L.; Yu, C.; Sun, J. Q.

    2015-03-01

    It is difficult to simulate the dynamical behavior of actual financial markets indexes effectively, especially when they have nonlinear characteristics. So it is significant to propose a mathematical model with these characteristics. In this paper, we investigate a generalized Weierstrass-Mandelbrot function (WMF) model with two nonlinear characteristics: fractal dimension D where 2 > D > 1.5 and Hurst exponent (H) where 1 > H > 0.5 firstly. And then we study the dynamical behavior of H for WMF as D and the spectrum of the time series γ change in three-dimensional space, respectively. Because WMF and the actual stock market indexes have two common features: fractal behavior using fractal dimension and long memory effect by Hurst exponent, we study the relationship between WMF and the actual stock market indexes. We choose a random value of γ and fixed value of D for WMF to simulate the S&P 500 indexes at different time ranges. As shown in the simulation results of three-dimensional space, we find that γ is important in WMF model and different γ may have the same effect for the nonlinearity of WMF. Then we calculate the skewness and kurtosis of actual Daily S&P 500 index in different time ranges which can be used to choose the value of γ. Based on these results, we choose appropriate γ, D and initial value into WMF to simulate Daily S&P 500 indexes. Using the fit line method in two-dimensional space for the simulated values, we find that the generalized WMF model is effective for simulating different actual stock market indexes in different time ranges. It may be useful for understanding the dynamical behavior of many different financial markets.

  19. Control of the growth of Microthrix parvicelle by using an aerobic selector--results of pilot and full scale plant operation.

    PubMed

    Lebek, M; Rosenwinkel, K H

    2002-01-01

    A two-stage wastewater treatment plant experiences bulking sludge problems in winter, correlating with Microthixparvicella abundance. Pilot and full-scale studies of the use of an aerobic selector to control M. parvicella had little success, probably resulting from long chain fatty acid retention in foam at the tank surface. Initial pilot studies with reduced foam retention showed better results. PMID:12216674

  20. Operating experience review of an INL gas monitoring system

    SciTech Connect

    Cadwallader, Lee C.; DeWall, K. G.; Herring, J. S.

    2015-03-12

    This article describes the operations of several types of gas monitors in use at the Idaho National Laboratory (INL) High Temperature Electrolysis Experiment (HTE) laboratory. The gases monitored in the lab room are hydrogen, carbon monoxide, carbon dioxide, and oxygen. The operating time, calibration, and both actual and unwanted alarms are described. The calibration session time durations are described. In addition, some simple calculations are given to estimate the reliability of these monitors and the results are compared to operating experiences of other types of monitors.