Research on the processing technology of elongated holes based on rotary ultrasonic drilling

NASA Astrophysics Data System (ADS)

Tong, Yi; Chen, Jianhua; Sun, Lipeng; Yu, Xin; Wang, Xin

2014-08-01

The optical glass is hard, brittle and difficult to process. Based on the method of rotating ultrasonic drilling, the study of single factor on drilling elongated holes was made in optical glass. The processing equipment was DAMA ultrasonic machine, and the machining tools were electroplated with diamond. Through the detection and analysis on the processing quality and surface roughness, the process parameters (the spindle speed, amplitude, feed rate) of rotary ultrasonic drilling were researched, and the influence of processing parameters on surface roughness was obtained, which will provide reference and basis for the actual processing.

Variable current speed controller for eddy current motors

DOEpatents

Gerth, H.L.; Bailey, J.M.; Casstevens, J.M.; Dixon, J.H.; Griffith, B.O.; Igou, R.E.

1982-03-12

A speed control system for eddy current motors is provided in which the current to the motor from a constant frequency power source is varied by comparing the actual motor speed signal with a setpoint speed signal to control the motor speed according to the selected setpoint speed. A three-phase variable voltage autotransformer is provided for controlling the voltage from a three-phase power supply. A corresponding plurality of current control resistors is provided in series with each phase of the autotransformer output connected to inputs of a three-phase motor. Each resistor is connected in parallel with a set of normally closed contacts of plurality of relays which are operated by control logic. A logic circuit compares the selected speed with the actual motor speed obtained from a digital tachometer monitoring the motor spindle speed and operated the relays to add or substract resistance equally in each phase of the motor input to vary the motor current to control the motor at the selected speed.

Implementation of Speed Variation in the Structural Dynamic Assessment of Turbomachinery Flow-Path Components

NASA Technical Reports Server (NTRS)

Brown, Andrew M.; Davis, R. Benjamin; DeHaye, Michael

2013-01-01

During the design of turbomachinery flow path components, the assessment of possible structural resonant conditions is critical. Higher frequency modes of these structures are frequently found to be subject to resonance, and in these cases, design criteria require a forced response analysis of the structure with the assumption that the excitation speed exactly equals the resonant frequency. The design becomes problematic if the response analysis shows a violation of the HCF criteria. One possible solution is to perform "finite-life" analysis, where Miner's rule is used to calculate the actual life in seconds in comparison to the required life. In this situation, it is beneficial to incorporate the fact that, for a variety of turbomachinery control reasons, the speed of the rotor does not actually dwell at a single value but instead dithers about a nominal mean speed and during the time that the excitation frequency is not equal to the resonant frequency, the damage accumulated by the structure is diminished significantly. Building on previous investigations into this process, we show that a steady-state assumption of the response is extremely accurate for this typical case, resulting in the ability to quickly account for speed variation in the finite-life analysis of a component which has previously had its peak dynamic stress at resonance calculated. A technique using Monte Carlo simulation is also presented which can be used when specific speed time histories are not available. The implementation of these techniques can prove critical for successful turbopump design, as the improvement in life when speed variation is considered is shown to be greater than a factor of two

Modelling and control algorithms of the cross conveyors line with multiengine variable speed drives

NASA Astrophysics Data System (ADS)

Cheremushkina, M. S.; Baburin, S. V.

2017-02-01

The paper deals with the actual problem of developing the control algorithm that meets the technical requirements of the mine belt conveyors, and enables energy and resource savings taking into account a random sort of traffic. The most effective method of solution of these tasks is the construction of control systems with the use of variable speed drives for asynchronous motors. The authors designed the mathematical model of the system ‘variable speed multiengine drive - conveyor - control system of conveyors’ that takes into account the dynamic processes occurring in the elements of the transport system, provides an assessment of the energy efficiency of application the developed algorithms, which allows one to reduce the dynamic overload in the belt to 15-20%.

Method and system for determining induction motor speed

DOEpatents

Parlos, Alexander G.; Bharadwaj, Raj M.

2004-03-30

A non-linear, semi-parametric neural network-based adaptive filter is utilized to determine the dynamic speed of a rotating rotor within an induction motor, without the explicit use of a speed sensor, such as a tachometer, is disclosed. The neural network-based filter is developed using actual motor current measurements, voltage measurements, and nameplate information. The neural network-based adaptive filter is trained using an estimated speed calculator derived from the actual current and voltage measurements. The neural network-based adaptive filter uses voltage and current measurements to determine the instantaneous speed of a rotating rotor. The neural network-based adaptive filter also includes an on-line adaptation scheme that permits the filter to be readily adapted for new operating conditions during operations.

49 CFR 229.117 - Speed indicators.

Code of Federal Regulations, 2012 CFR

2012-10-01

... locomotive at speeds in excess of 20 miles per hour shall be equipped with a speed indicator which is— (1) Accurate within ±3 miles per hour of actual speed at speeds of 10 to 30 miles per hour and accurate within ±5 miles per hour at speeds above 30 miles per hour; and (2) Clearly readable from the engineer's...

49 CFR 229.117 - Speed indicators.

Code of Federal Regulations, 2013 CFR

2013-10-01

... locomotive at speeds in excess of 20 miles per hour shall be equipped with a speed indicator which is— (1) Accurate within ±3 miles per hour of actual speed at speeds of 10 to 30 miles per hour and accurate within ±5 miles per hour at speeds above 30 miles per hour; and (2) Clearly readable from the engineer's...

49 CFR 229.117 - Speed indicators.

Code of Federal Regulations, 2014 CFR

2014-10-01

... locomotive at speeds in excess of 20 miles per hour shall be equipped with a speed indicator which is— (1) Accurate within ±3 miles per hour of actual speed at speeds of 10 to 30 miles per hour and accurate within ±5 miles per hour at speeds above 30 miles per hour; and (2) Clearly readable from the engineer's...

Development and training of a learning expert system in an autonomous mobile robot via simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spelt, P.F.; Lyness, E.; DeSaussure, G.

1989-11-01

The Center for Engineering Systems Advanced Research (CESAR) conducts basic research in the area of intelligent machines. Recently at CESAR a learning expert system was created to operate on board an autonomous robot working at a process control panel. The authors discuss two-computer simulation system used to create, evaluate and train this learning system. The simulation system has a graphics display of the current status of the process being simulated, and the same program which does the simulating also drives the actual control panel. Simulation results were validated on the actual robot. The speed and safety values of using amore » computerized simulator to train a learning computer, and future uses of the simulation system, are discussed.« less

Matching optical flow to motor speed in virtual reality while running on a treadmill.

PubMed

Caramenti, Martina; Lafortuna, Claudio L; Mugellini, Elena; Abou Khaled, Omar; Bresciani, Jean-Pierre; Dubois, Amandine

2018-01-01

We investigated how visual and kinaesthetic/efferent information is integrated for speed perception in running. Twelve moderately trained to trained subjects ran on a treadmill at three different speeds (8, 10, 12 km/h) in front of a moving virtual scene. They were asked to match the visual speed of the scene to their running speed-i.e., treadmill's speed. For each trial, participants indicated whether the scene was moving slower or faster than they were running. Visual speed was adjusted according to their response using a staircase until the Point of Subjective Equality (PSE) was reached, i.e., until visual and running speed were perceived as equivalent. For all three running speeds, participants systematically underestimated the visual speed relative to their actual running speed. Indeed, the speed of the visual scene had to exceed the actual running speed in order to be perceived as equivalent to the treadmill speed. The underestimation of visual speed was speed-dependent, and percentage of underestimation relative to running speed ranged from 15% at 8km/h to 31% at 12km/h. We suggest that this fact should be taken into consideration to improve the design of attractive treadmill-mediated virtual environments enhancing engagement into physical activity for healthier lifestyles and disease prevention and care.

Matching optical flow to motor speed in virtual reality while running on a treadmill

PubMed Central

Lafortuna, Claudio L.; Mugellini, Elena; Abou Khaled, Omar

2018-01-01

We investigated how visual and kinaesthetic/efferent information is integrated for speed perception in running. Twelve moderately trained to trained subjects ran on a treadmill at three different speeds (8, 10, 12 km/h) in front of a moving virtual scene. They were asked to match the visual speed of the scene to their running speed–i.e., treadmill’s speed. For each trial, participants indicated whether the scene was moving slower or faster than they were running. Visual speed was adjusted according to their response using a staircase until the Point of Subjective Equality (PSE) was reached, i.e., until visual and running speed were perceived as equivalent. For all three running speeds, participants systematically underestimated the visual speed relative to their actual running speed. Indeed, the speed of the visual scene had to exceed the actual running speed in order to be perceived as equivalent to the treadmill speed. The underestimation of visual speed was speed-dependent, and percentage of underestimation relative to running speed ranged from 15% at 8km/h to 31% at 12km/h. We suggest that this fact should be taken into consideration to improve the design of attractive treadmill-mediated virtual environments enhancing engagement into physical activity for healthier lifestyles and disease prevention and care. PMID:29641564

A brief review on the recent advances in scramjet engine

NASA Astrophysics Data System (ADS)

Choubey, Gautam; Pandey, K. M.; Maji, Ambarish; Deshamukhya, Tuhin

2017-07-01

The scramjet engine is the most favourable air breathing propulsive system and suitable option for high-speed flight (Ma<4). Several scientists across the globe are continuously working on the advancement of the high-speed scramjet engine due to its implementation in the military missiles, low-cost access to space etc. The mixing phenomena associated with air and fuel is the salient feature for the effective combustion process and the fuel and air should be mixed adequately before entering into the combustor. But the key challenges associated with scramjet engine are the high speed of air inside the combustor and low residence time which actually deteriorate the combustion phenomena. That's why numerous computational, as well as experimental researches are being carried out by several researchers. The flow-field inside the scramjet engine is very complex. Hence an elaborated approach of the complicated combustion and mixing process inside the combustor is essential for the upgradation of the effective scramjet engine. This paper clearly signifies a brief review of the current development in scramjet engine.

In the year 2525, if x ray is still alive, if lithography can survive, they may find...

NASA Astrophysics Data System (ADS)

Nistler, John L.; Michael, Mark; Hause, Fred N.; Edwards, Richard D.

1998-12-01

Data and discussions will be presented on the NTRM, National Technology Roadmap, for reticles based on a Process Integration perception. Specifically two layers are considered for this paper, the gate layer which is primarily a chrome geometry mask with a lot of open glass and a local interconnect layer which is primarily a chrome plate using clear geometries. Information from other sources is used where appropriate and actual in-house data is used to illustrate specific points. Realizing that demands from different customers for specific types of features tend to drive specific mask makers and their decisions on equipment purchases and processes. We attempt to help predict where Integration approaches have either caused a lag in technology pushes or have actually speeded up certain requirements. Discussions of integration requirements, which tend to push maskmakers, will be presented. Along with typical design approaches in OPC and PSM which either will push technology or actually slow down the trend towards smaller geometries. In addition, data will be presented showing how specific stepper characteristics may actually drive the customer's criteria, thus changing the requirements from customer to customer.

Spatial 3D infrastructure: display-independent software framework, high-speed rendering electronics, and several new displays

NASA Astrophysics Data System (ADS)

Chun, Won-Suk; Napoli, Joshua; Cossairt, Oliver S.; Dorval, Rick K.; Hall, Deirdre M.; Purtell, Thomas J., II; Schooler, James F.; Banker, Yigal; Favalora, Gregg E.

2005-03-01

We present a software and hardware foundation to enable the rapid adoption of 3-D displays. Different 3-D displays - such as multiplanar, multiview, and electroholographic displays - naturally require different rendering methods. The adoption of these displays in the marketplace will be accelerated by a common software framework. The authors designed the SpatialGL API, a new rendering framework that unifies these display methods under one interface. SpatialGL enables complementary visualization assets to coexist through a uniform infrastructure. Also, SpatialGL supports legacy interfaces such as the OpenGL API. The authors" first implementation of SpatialGL uses multiview and multislice rendering algorithms to exploit the performance of modern graphics processing units (GPUs) to enable real-time visualization of 3-D graphics from medical imaging, oil & gas exploration, and homeland security. At the time of writing, SpatialGL runs on COTS workstations (both Windows and Linux) and on Actuality"s high-performance embedded computational engine that couples an NVIDIA GeForce 6800 Ultra GPU, an AMD Athlon 64 processor, and a proprietary, high-speed, programmable volumetric frame buffer that interfaces to a 1024 x 768 x 3 digital projector. Progress is illustrated using an off-the-shelf multiview display, Actuality"s multiplanar Perspecta Spatial 3D System, and an experimental multiview display. The experimental display is a quasi-holographic view-sequential system that generates aerial imagery measuring 30 mm x 25 mm x 25 mm, providing 198 horizontal views.

Laser-Aided Directed Energy Deposition of Steel Powder over Flat Surfaces and Edges.

PubMed

Caiazzo, Fabrizia; Alfieri, Vittorio

2018-03-16

In the framework of Additive Manufacturing of metals, Directed Energy Deposition of steel powder over flat surfaces and edges has been investigated in this paper. The aims are the repair and overhaul of actual, worn-out, high price sensitive metal components. A full-factorial experimental plan has been arranged, the results have been discussed in terms of geometry, microhardness and thermal affection as functions of the main governing parameters, laser power, scanning speed and mass flow rate; dilution and catching efficiency have been evaluated as well to compare quality and effectiveness of the process under conditions of both flat and edge depositions. Convincing results are presented to give grounds for shifting the process to actual applications: namely, no cracks or pores have been found in random cross-sections of the samples in the processing window. Interestingly an effect of the scanning conditions has been proven on the resulting hardness in the fusion zone; therefore, the mechanical characteristics are expected to depend on the processing parameters.

Laser-Aided Directed Energy Deposition of Steel Powder over Flat Surfaces and Edges

PubMed Central

2018-01-01

In the framework of Additive Manufacturing of metals, Directed Energy Deposition of steel powder over flat surfaces and edges has been investigated in this paper. The aims are the repair and overhaul of actual, worn-out, high price sensitive metal components. A full-factorial experimental plan has been arranged, the results have been discussed in terms of geometry, microhardness and thermal affection as functions of the main governing parameters, laser power, scanning speed and mass flow rate; dilution and catching efficiency have been evaluated as well to compare quality and effectiveness of the process under conditions of both flat and edge depositions. Convincing results are presented to give grounds for shifting the process to actual applications: namely, no cracks or pores have been found in random cross-sections of the samples in the processing window. Interestingly an effect of the scanning conditions has been proven on the resulting hardness in the fusion zone; therefore, the mechanical characteristics are expected to depend on the processing parameters. PMID:29547571

In Situ Monitoring of Particle Consolidation During Low Pressure Cold Spray by Ultrasonic Techniques

NASA Astrophysics Data System (ADS)

Maev, R. Gr.; Titov, S.; Leshchynsky, V.; Dzhurinskiy, D.; Lubrick, M.

2011-06-01

This study attempts to test the viability of the examination of the cold spray process using acoustic methods, specifically in situ testing during the actual spray process itself. Multiple composites studied by flat and multi-channel transducers as well as the results of actual online measurements are presented. It is shown that the final thickness as well as the dynamics of buildup can be evaluated (including plotting rates of buildup). Cross sections of the coating thickness are also easy to obtain and show true profiles of the coating. The data can also be used to generate real estimates for nozzle speed and spray diameter. Finally, comparisons of real thickness and acoustically estimated thickness show a close linear relationship. The data clearly show that online acoustic measurement is a viable method for estimating thickness buildup.

Wind speed perception and risk.

PubMed

Agdas, Duzgun; Webster, Gregory D; Masters, Forrest J

2012-01-01

How accurately do people perceive extreme wind speeds and how does that perception affect the perceived risk? Prior research on human-wind interaction has focused on comfort levels in urban settings or knock-down thresholds. No systematic experimental research has attempted to assess people's ability to estimate extreme wind speeds and perceptions of their associated risks. We exposed 76 people to 10, 20, 30, 40, 50, and 60 mph (4.5, 8.9, 13.4, 17.9, 22.3, and 26.8 m/s) winds in randomized orders and asked them to estimate wind speed and the corresponding risk they felt. Multilevel modeling showed that people were accurate at lower wind speeds but overestimated wind speeds at higher levels. Wind speed perceptions mediated the direct relationship between actual wind speeds and perceptions of risk (i.e., the greater the perceived wind speed, the greater the perceived risk). The number of tropical cyclones people had experienced moderated the strength of the actual-perceived wind speed relationship; consequently, mediation was stronger for people who had experienced fewer storms. These findings provide a clearer understanding of wind and risk perception, which can aid development of public policy solutions toward communicating the severity and risks associated with natural disasters.

15 CFR 265.12 - Speeding or reckless driving.

Code of Federal Regulations, 2014 CFR

2014-01-01

... of traffic, weather, and road surface and having regard to the actual and potential hazards existing...) of this section, the speed limit on the site is 25 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess of the speed limit. ...

15 CFR 265.12 - Speeding or reckless driving.

Code of Federal Regulations, 2012 CFR

2012-01-01

... of traffic, weather, and road surface and having regard to the actual and potential hazards existing...) of this section, the speed limit on the site is 25 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess of the speed limit. ...

15 CFR 265.12 - Speeding or reckless driving.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of traffic, weather, and road surface and having regard to the actual and potential hazards existing...) of this section, the speed limit on the site is 25 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess of the speed limit. ...

15 CFR 265.12 - Speeding or reckless driving.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of traffic, weather, and road surface and having regard to the actual and potential hazards existing...) of this section, the speed limit on the site is 25 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess of the speed limit. ...

How accurate are Omron X-HJ-304-E and Yamax SW-700/701 pedometers at different speeds and various inclinations?

PubMed

Wallmann-Sperlich, B; Froboese, I; Reed, J L; Mathes, S; Sperlich, B

2015-01-01

The purpose of this study was to investigate step count and energy expenditure accuracy of the piezoelectric Omron (Walking Style X-HJ-304-E) and spring-levered Yamax (Digi-Walker-SW-700/701) pedometers at different speeds and various inclinations. Thirty subjects (15 females, aged: 24 ± 3 years) completed eleven 5-min trials at different treadmill speeds and inclinations (3.24 km∙h⁻¹ [inclination: 0, 9, 20%], 4.68 km∙h⁻¹ [0, 9, 20%], 6.48 km∙h⁻¹ [0, 9%], 9 km∙h⁻¹ [0%], 10.8 km∙h⁻¹ [0%], 12.6 km∙h⁻¹ [0%]). During each trial, an investigator recorded actual steps with a hand tally counter. Actual energy expenditure was measured using a portable indirect calorimeter. The Omron pedometer revealed high step count accuracy for all speeds and inclinations when worn on the hip or a backpack (Mean % of actual steps: 99.6%; Range: 95.8-101.3%). The Yamax pedometer revealed high step count accuracy (Mean % of actual steps: 99.8%; Range: 96.2-103.3%) when worn on the left hip at 6.48-12.6 km∙h⁻¹ (0%), 4.68 km∙h⁻¹ (9%, 20%), 6.48 km∙h⁻¹ (9%) and on the right hip at 10.8 km∙h⁻¹ (0%) and 6.48 km∙h⁻¹ (9%). The accuracy of the Omron and Yamax determined energy expenditure was poor (57.9-59.7%) when compared to indirect calorimetry. The Omron pedometer provides accurate step counts when worn on the hip and backpack at all tested speeds and inclinations. We therefore suggest an accurate application of this device for walking, hiking and running at moderate speeds. Both pedometers underestimated energy expenditure.

New VASCAR-plus timing mechanism test results

DOT National Transportation Integrated Search

1993-04-01

In a previous study (Analysis of VASCAR, DOT HS 807-748, May 1993), it was found that the VASCAR-plus timing mechanism was biased against the speed limit violator. The VASCAR speed reading was higher than the actual speed. At that time, it was sugges...

32 CFR 263.6 - Speeding or reckless driving.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., weather, and road surface and having regard to the actual and potential hazards existing. (b) Except when a special hazard exists that requires lower speed, the speed limit on the site is 15 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess...

32 CFR 263.6 - Speeding or reckless driving.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., weather, and road surface and having regard to the actual and potential hazards existing. (b) Except when a special hazard exists that requires lower speed, the speed limit on the site is 15 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess...

32 CFR 263.6 - Speeding or reckless driving.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., weather, and road surface and having regard to the actual and potential hazards existing. (b) Except when a special hazard exists that requires lower speed, the speed limit on the site is 15 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess...

32 CFR 263.6 - Speeding or reckless driving.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., weather, and road surface and having regard to the actual and potential hazards existing. (b) Except when a special hazard exists that requires lower speed, the speed limit on the site is 15 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess...

32 CFR 263.6 - Speeding or reckless driving.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., weather, and road surface and having regard to the actual and potential hazards existing. (b) Except when a special hazard exists that requires lower speed, the speed limit on the site is 15 m.p.h., unless another speed limit has been duly posted, and no person shall drive a motor vehicle on the site in excess...

High speed machining of space shuttle external tank liquid hydrogen barrel panel

NASA Technical Reports Server (NTRS)

Hankins, J. D.

1983-01-01

Actual and projected optimum High Speed Machining data for producing shuttle external tank liquid hydrogen barrel panels of aluminum alloy 2219-T87 are reported. The data included various machining parameters; e.g., spindle speeds, cutting speed, table feed, chip load, metal removal rate, horsepower, cutting efficiency, cutter wear (lack of) and chip removal methods.

High speed machining of space shuttle external tank liquid hydrogen barrel panel

NASA Astrophysics Data System (ADS)

Hankins, J. D.

1983-11-01

Actual and projected optimum High Speed Machining data for producing shuttle external tank liquid hydrogen barrel panels of aluminum alloy 2219-T87 are reported. The data included various machining parameters; e.g., spindle speeds, cutting speed, table feed, chip load, metal removal rate, horsepower, cutting efficiency, cutter wear (lack of) and chip removal methods.

Research on Correlation between Vehicle Cycle and Engine Cycle in Heavy-duty commercial vehicle

NASA Astrophysics Data System (ADS)

lin, Chen; Zhong, Wang; Shuai, Liu

2017-12-01

In order to study the correlation between vehicle cycle and engine cycle in heavy commercial vehicles, the conversion model of vehicle cycle to engine cycle is constructed based on the vehicle power system theory and shift strategy, which considers the verification on diesel truck. The results show that the model has high rationality and reliability in engine operation. In the acceleration process of high speed, the difference of model gear selection leads to the actual deviation. Compared with the drum test, the engine speed distribution obtained by the model deviates to right, which fits to the lower grade. The grade selection has high influence on the model.

Accuracy and high-speed technique for autoprocessing of Young's fringes

NASA Astrophysics Data System (ADS)

Chen, Wenyi; Tan, Yushan

1991-12-01

In this paper, an accurate and high-speed method for auto-processing of Young's fringes is proposed. A group of 1-D sampled intensity values along three or more different directions are taken from Young's fringes, and the fringe spacings of each direction are obtained by 1-D FFT respectively. Two directions that have smaller fringe spacing are selected from all directions. The accurate fringe spacings along these two directions are obtained by using orthogonal coherent phase detection technique (OCPD). The actual spacing and angle of Young's fringes, therefore, can be calculated. In this paper, the principle of OCPD is introduced in detail. The accuracy of the method is evaluated theoretically and experimentally.

In-line and Real-time Monitoring of Resonant Acoustic Mixing by Near-infrared Spectroscopy Combined with Chemometric Technology for Process Analytical Technology Applications in Pharmaceutical Powder Blending Systems.

PubMed

Tanaka, Ryoma; Takahashi, Naoyuki; Nakamura, Yasuaki; Hattori, Yusuke; Ashizawa, Kazuhide; Otsuka, Makoto

2017-01-01

Resonant acoustic ® mixing (RAM) technology is a system that performs high-speed mixing by vibration through the control of acceleration and frequency. In recent years, real-time process monitoring and prediction has become of increasing interest, and process analytical technology (PAT) systems will be increasingly introduced into actual manufacturing processes. This study examined the application of PAT with the combination of RAM, near-infrared spectroscopy, and chemometric technology as a set of PAT tools for introduction into actual pharmaceutical powder blending processes. Content uniformity was based on a robust partial least squares regression (PLSR) model constructed to manage the RAM configuration parameters and the changing concentration of the components. As a result, real-time monitoring may be possible and could be successfully demonstrated for in-line real-time prediction of active pharmaceutical ingredients and other additives using chemometric technology. This system is expected to be applicable to the RAM method for the risk management of quality.

Experimental study of icing accretion on a rotating conical spinner

NASA Astrophysics Data System (ADS)

Chen, Ningli; Ji, Honghu; Hu, Yaping; Wang, Jian; Cao, Guangzhou

2015-12-01

A reduced scale experiment has been conducted to investigate the icing accretion procedure on a rotating spinner of 60° cone angle. The experiment was carried out in a small scale ice wind tunnel with three different rotating speeds of the spinner. The experimental conditions were determined from the actual icing condition of the spinner of a turbofan engine by using the similarity theory, which considers the rotating effects. The ice thickness on the spinner was got from the image taken by the high speed camera, by image processing. The results of this investigation show that under the experimental condition, ice on the spinner's tip of three different rotating speeds are all glaze ice and about the same thick. However, on the downstream surface of the spinner, ice shape on the rotating spinner is different from that on the stationary spinner. It is uneven glaze ice on the stationary spinner while it is `particle ice' when the rotating speed is 8240 rpm and it is `needle ice' when the rotating speed is 15,200 rpm. The experiment also reveals that when the rotating speed is higher, the ice layer is thicker.

Real-time simulation clock

NASA Technical Reports Server (NTRS)

Bennington, Donald R. (Inventor); Crawford, Daniel J. (Inventor)

1990-01-01

The invention is a clock for synchronizing operations within a high-speed, distributed data processing network. The clock is actually a distributed system comprising a central clock and multiple site clock interface units (SCIUs) which are connected by means of a fiber optic star network and which operate under control of separate clock software. The presently preferred embodiment is a part of the flight simulation system now in current use at the NASA Langley Research Center.

Slot angle detecting method for fiber fixed chip

NASA Astrophysics Data System (ADS)

Zhang, Jiaquan; Wang, Jiliang; Zhou, Chaochao

2018-04-01

The slot angle of fiber fixed chip has a significant impact on performance of photoelectric devices. In order to solve the actual engineering problem, this paper put forward a detecting method based on imaging processing. Because the images have very low contrast that is hardly segmented, so this paper proposes imaging segment methods based on edge character. Then get fixed chip edge line slope k2 and calculate the fiber fixed slot line slope k1, which can be used calculating the slot angle. Lastly, test the repeatability and accuracy of system, which show that this method has very fast operation speed and good robustness. Clearly, it is also satisfied to the actual demand of fiber fixed chip slot angle detection.

Vehicle longitudinal velocity estimation during the braking process using unknown input Kalman filter

NASA Astrophysics Data System (ADS)

Moaveni, Bijan; Khosravi Roqaye Abad, Mahdi; Nasiri, Sayyad

2015-10-01

In this paper, vehicle longitudinal velocity during the braking process is estimated by measuring the wheels speed. Here, a new algorithm based on the unknown input Kalman filter is developed to estimate the vehicle longitudinal velocity with a minimum mean square error and without using the value of braking torque in the estimation procedure. The stability and convergence of the filter are analysed and proved. Effectiveness of the method is shown by designing a real experiment and comparing the estimation result with actual longitudinal velocity computing from a three-axis accelerometer output.

A Pause-then-Cancel model of stopping: evidence from basal ganglia neurophysiology.

PubMed

Schmidt, Robert; Berke, Joshua D

2017-04-19

Many studies have implicated the basal ganglia in the suppression of action impulses ('stopping'). Here, we discuss recent neurophysiological evidence that distinct hypothesized processes involved in action preparation and cancellation can be mapped onto distinct basal ganglia cell types and pathways. We examine how movement-related activity in the striatum is related to a 'Go' process and how going may be modulated by brief epochs of beta oscillations. We then describe how, rather than a unitary 'Stop' process, there appear to be separate, complementary 'Pause' and 'Cancel' mechanisms. We discuss the implications of these stopping subprocesses for the interpretation of the stop-signal reaction time-in particular, some activity that seems too slow to causally contribute to stopping when assuming a single Stop processes may actually be fast enough under a Pause-then-Cancel model. Finally, we suggest that combining complementary neural mechanisms that emphasize speed or accuracy respectively may serve more generally to optimize speed-accuracy trade-offs.This article is part of the themed issue 'Movement suppression: brain mechanisms for stopping and stillness'. © 2017 The Author(s).

Accuracy of visual estimates of joint angle and angular velocity using criterion movements.

PubMed

Morrison, Craig S; Knudson, Duane; Clayburn, Colby; Haywood, Philip

2005-06-01

A descriptive study to document undergraduate physical education majors' (22.8 +/- 2.4 yr. old) estimates of sagittal plane elbow angle and angular velocity of elbow flexion visually was performed. 42 subjects rated videotape replays of 30 movements organized into three speeds of movement and two criterion elbow angles. Video images of the movements were analyzed with Peak Motus to measure actual values of elbow angles and peak angular velocity. Of the subjects 85.7% had speed ratings significantly correlated with true peak elbow angular velocity in all three angular velocity conditions. Few (16.7%) subjects' ratings of elbow angle correlated significantly with actual angles. Analysis of the subjects with good ratings showed the accuracy of visual ratings was significantly related to speed, with decreasing accuracy for slower speeds of movement. The use of criterion movements did not improve the small percentage of novice observers who could accurately estimate body angles during movement.

Visualization of electrolyte filling process and influence of vacuum during filling for hard case prismatic lithium ion cells by neutron imaging to optimize the production process

NASA Astrophysics Data System (ADS)

Weydanz, W. J.; Reisenweber, H.; Gottschalk, A.; Schulz, M.; Knoche, T.; Reinhart, G.; Masuch, M.; Franke, J.; Gilles, R.

2018-03-01

The process of filling electrolyte into lithium ion cells is time consuming and critical to the overall battery quality. However, this process is not well understood. This is partially due to the fact, that it is hard to observe it in situ. A powerful tool for visualization of the process is neutron imaging. The filling and wetting process of the electrode stack can be clearly visualized in situ without destruction of the actual cell. The wetting of certain areas inside the electrode stack can clearly be seen when using this technique. Results showed that wetting of the electrode stack takes place in a mostly isotropic manner from the outside towards a center point of the cell at very similar speed. When the electrolyte reaches the center point, the wetting process can be considered complete. The electrode wetting is a slow but rather steady process for hard case prismatic cells. It starts with a certain speed, which is reduced over the progress of the wetting. Vacuum can assist the process and accelerate it by about a factor of two as was experimentally shown. This gives a considerable time and cost advantage for designing the production process for large-scale battery cell production.

Fabrication process analysis and experimental verification for aluminum bipolar plates in fuel cells by vacuum die-casting

NASA Astrophysics Data System (ADS)

Jin, Chul Kyu; Kang, Chung Gil

2011-10-01

There are various methods for the fabrication of bipolar plates, but these are still limited to machining and stamping processes. High-pressure die casting (HPDC) is an ideal process for the manufacture of bipolar plates This study aims to investigate the formability of bipolar plates for polymer electrolyte membrane fuel cells (PEMFCs) fabricated by vacuum HPDC of an Al-Mg alloy (ALDC6). The cavity of the mold consisted of a thin-walled plate (200 mm × 200 mm × 0.8 mm) with a layer of serpentine channel (50 mm × 50 mm). The location and direction of the channel in the final mold design was determined by computational simulation (MAGMA soft). In addition, simulation results for different conditions of plunger stroke control were compared to those from actual die-casting experiments. Under a vacuum pressure of 35 kPa and for injection speeds of 0.3 and 2.5 m s-1 in the low and high speed regions, respectively, the samples had few casting defects. In addition, the hardness was higher and porosity in microstructure was less than those of the samples made under other injection speed conditions. In case of thin-walled plates, vacuum die casting is beneficial in terms of formability compared to conventional die casting.

The development speed paradox: can increasing development speed reduce R&D productivity?

PubMed

Lendrem, Dennis W; Lendrem, B Clare

2014-03-01

In the 1990s the pharmaceutical industry sought to increase R&D productivity by shifting development tasks into parallel to reduce development cycle times and increase development speed. This paper presents a simple model demonstrating that, when attrition rates are high as in pharmaceutical development, such development speed initiatives can increase the expected time for the first successful molecule to complete development. Increasing the development speed of successful molecules could actually reduce R&D productivity - the development speed paradox. Copyright © 2013 Elsevier Ltd. All rights reserved.

Parameters optimization of laser brazing in crimping butt using Taguchi and BPNN-GA

NASA Astrophysics Data System (ADS)

Rong, Youmin; Zhang, Zhen; Zhang, Guojun; Yue, Chen; Gu, Yafei; Huang, Yu; Wang, Chunming; Shao, Xinyu

2015-04-01

The laser brazing (LB) is widely used in the automotive industry due to the advantages of high speed, small heat affected zone, high quality of welding seam, and low heat input. Welding parameters play a significant role in determining the bead geometry and hence quality of the weld joint. This paper addresses the optimization of the seam shape in LB process with welding crimping butt of 0.8 mm thickness using back propagation neural network (BPNN) and genetic algorithm (GA). A 3-factor, 5-level welding experiment is conducted by Taguchi L25 orthogonal array through the statistical design method. Then, the input parameters are considered here including welding speed, wire speed rate, and gap with 5 levels. The output results are efficient connection length of left side and right side, top width (WT) and bottom width (WB) of the weld bead. The experiment results are embed into the BPNN network to establish relationship between the input and output variables. The predicted results of the BPNN are fed to GA algorithm that optimizes the process parameters subjected to the objectives. Then, the effects of welding speed (WS), wire feed rate (WF), and gap (GAP) on the sum values of bead geometry is discussed. Eventually, the confirmation experiments are carried out to demonstrate the optimal values were effective and reliable. On the whole, the proposed hybrid method, BPNN-GA, can be used to guide the actual work and improve the efficiency and stability of LB process.

Fast and Famous: Looking for the Fastest Speed at Which a Face Can be Recognized

PubMed Central

Barragan-Jason, Gladys; Besson, Gabriel; Ceccaldi, Mathieu; Barbeau, Emmanuel J.

2012-01-01

Face recognition is supposed to be fast. However, the actual speed at which faces can be recognized remains unknown. To address this issue, we report two experiments run with speed constraints. In both experiments, famous faces had to be recognized among unknown ones using a large set of stimuli to prevent pre-activation of features which would speed up recognition. In the first experiment (31 participants), recognition of famous faces was investigated using a rapid go/no-go task. In the second experiment, 101 participants performed a highly time constrained recognition task using the Speed and Accuracy Boosting procedure. Results indicate that the fastest speed at which a face can be recognized is around 360–390 ms. Such latencies are about 100 ms longer than the latencies recorded in similar tasks in which subjects have to detect faces among other stimuli. We discuss which model of activation of the visual ventral stream could account for such latencies. These latencies are not consistent with a purely feed-forward pass of activity throughout the visual ventral stream. An alternative is that face recognition relies on the core network underlying face processing identified in fMRI studies (OFA, FFA, and pSTS) and reentrant loops to refine face representation. However, the model of activation favored is that of an activation of the whole visual ventral stream up to anterior areas, such as the perirhinal cortex, combined with parallel and feed-back processes. Further studies are needed to assess which of these three models of activation can best account for face recognition. PMID:23460051

14 CFR 91.611 - Authorization for ferry flight with one engine inoperative.

Code of Federal Regulations, 2010 CFR

2010-01-01

... chapter but with— (i) The actual steady gradient of the final takeoff climb requirement not less than 1.2... less than the two-engine inoperative trim speed for the actual steady gradient of the final takeoff...

Walking Speed Influences the Effects of Implicit Visual Feedback Distortion on Modulation of Gait Symmetry

PubMed Central

Maestas, Gabrielle; Hu, Jiyao; Trevino, Jessica; Chunduru, Pranathi; Kim, Seung-Jae; Lee, Hyunglae

2018-01-01

The use of visual feedback in gait rehabilitation has been suggested to promote recovery of locomotor function by incorporating interactive visual components. Our prior work demonstrated that visual feedback distortion of changes in step length symmetry entails an implicit or unconscious adaptive process in the subjects’ spatial gait patterns. We investigated whether the effect of the implicit visual feedback distortion would persist at three different walking speeds (slow, self-preferred and fast speeds) and how different walking speeds would affect the amount of adaption. In the visual feedback distortion paradigm, visual vertical bars portraying subjects’ step lengths were distorted so that subjects perceived their step lengths to be asymmetric during testing. Measuring the adjustments in step length during the experiment showed that healthy subjects made spontaneous modulations away from actual symmetry in response to the implicit visual distortion, no matter the walking speed. In all walking scenarios, the effects of implicit distortion became more significant at higher distortion levels. In addition, the amount of adaptation induced by the visual distortion was significantly greater during walking at preferred or slow speed than at the fast speed. These findings indicate that although a link exists between supraspinal function through visual system and human locomotion, sensory feedback control for locomotion is speed-dependent. Ultimately, our results support the concept that implicit visual feedback can act as a dominant form of feedback in gait modulation, regardless of speed. PMID:29632481

Design of a High Speed Data Capture Device for a Coherent Radar Application

DTIC Science & Technology

2006-11-01

of the RGASM is discussed, then the primary differences between coherent and non-coherent processing are compared. A basic digital receiver is then...IPP. 19 In-Phase Data Transfer Quadrature Data Transfer Label: Fuction : IQ-Sel Signifies whether data present on the bus is In-Phase or Quadrature...430S_IIZ _ l -.. t....!.... Label: Fuction : ADRS 16-bit address bus value DATA Actual 16-bit value of the data on the bus BUSEN* Bus enable READY* Bus

Laser Engineered Net Shape (LENS) Technology for the Repair of Ni-Base Superalloy Turbine Components

NASA Astrophysics Data System (ADS)

Liu, Dejian; Lippold, John C.; Li, Jia; Rohklin, Stan R.; Vollbrecht, Justin; Grylls, Richard

2014-09-01

The capability of the laser engineered net shape (LENS) process was evaluated for the repair of casting defects and improperly machined holes in gas turbine engine components. Various repair geometries, including indentations, grooves, and through-holes, were used to simulate the actual repair of casting defects and holes in two materials: Alloy 718 and Waspaloy. The influence of LENS parameters, including laser energy density, laser scanning speed, and deposition pattern, on the repair of these defects and holes was studied. Laser surface remelting of the substrate prior to repair was used to remove machining defects and prevent heat-affected zone (HAZ) liquation cracking. Ultrasonic nondestructive evaluation techniques were used as a possible approach for detecting lack-of-fusion in repairs. Overall, Alloy 718 exhibited excellent repair weldability, with essentially no defects except for some minor porosity in repairs representative of deep through-holes and simulated large area casting defects. In contrast, cracking was initially observed during simulated repair of Waspaloy. Both solidification cracking and HAZ liquation cracking were observed in the repairs, especially under conditions of high heat input (high laser power and/or low scanning speed). For Waspaloy, the degree of cracking was significantly reduced and, in most cases, completely eliminated by the combination of low laser energy density and relatively high laser scanning speeds. It was found that through-hole repairs of Waspaloy made using a fine powder size exhibited excellent repair weldability and were crack-free relative to repairs using coarser powder. Simulated deep (7.4 mm) blind-hole repairs, representative of an actual Waspaloy combustor case, were successfully produced by the combination use of fine powder and relatively high laser scanning speeds.

Motor vehicle speeds on Connecticut highways

DOT National Transportation Integrated Search

1936-01-01

The research study described in the following pages was undertaken to determine the actual speed of vehicles on Connecticut Highways. It was made in connection with a general survey of highway traffic in the State, carried on jointly by the United St...

Development of a Computing Cluster At the University of Richmond

NASA Astrophysics Data System (ADS)

Carbonneau, J.; Gilfoyle, G. P.; Bunn, E. F.

2010-11-01

The University of Richmond has developed a computing cluster to support the massive simulation and data analysis requirements for programs in intermediate-energy nuclear physics, and cosmology. It is a 20-node, 240-core system running Red Hat Enterprise Linux 5. We have built and installed the physics software packages (Geant4, gemc, MADmap...) and developed shell and Perl scripts for running those programs on the remote nodes. The system has a theoretical processing peak of about 2500 GFLOPS. Testing with the High Performance Linpack (HPL) benchmarking program (one of the standard benchmarks used by the TOP500 list of fastest supercomputers) resulted in speeds of over 900 GFLOPS. The difference between the maximum and measured speeds is due to limitations in the communication speed among the nodes; creating a bottleneck for large memory problems. As HPL sends data between nodes, the gigabit Ethernet connection cannot keep up with the processing power. We will show how both the theoretical and actual performance of the cluster compares with other current and past clusters, as well as the cost per GFLOP. We will also examine the scaling of the performance when distributed to increasing numbers of nodes.

Innovations in using virtual reality to study how children cross streets in traffic: evidence for evasive action skills.

PubMed

Morrongiello, Barbara A; Corbett, Michael; Milanovic, Melissa; Pyne, Sarah; Vierich, Robin

2015-08-01

Children in middle childhood are at an increased risk for injury in pedestrian environments. This study examined whether they are capable of showing evasive action (ie, adjusting crossing speed) to avoid injury when crossing streets. The study used a fully immersive virtual reality (VR) system interfaced with a three-dimensional movement measurement system so that the actual crossing behaviour of 7-10-year-old children under different traffic conditions could be precisely measured. Relating outcomes to that which would have been obtained based on using the approach of estimating walking speed and assuming a constant speed provided insights into the realised benefits of the current movement monitoring VR system. Controlling for age and sex, children showed evasive action, crossing more quickly as traffic conditions became more risky. Using an average and assuming a constant walking speed underestimated actual walking speed, failing to capture evasive action and leading to overestimation of children being hit compared with the actual incidence of hits. VR technology is a valuable tool for assessing child pedestrian behaviour. However, systems need to allow the child to cross the street so their level of pedestrian skill is appropriately measured. The current findings provide the first evidence that children are capable of implementing evasive action in reaction to risky traffic conditions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Simulation of a master-slave event set processor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Comfort, J.C.

1984-03-01

Event set manipulation may consume a considerable amount of the computation time spent in performing a discrete-event simulation. One way of minimizing this time is to allow event set processing to proceed in parallel with the remainder of the simulation computation. The paper describes a multiprocessor simulation computer, in which all non-event set processing is performed by the principal processor (called the host). Event set processing is coordinated by a front end processor (the master) and actually performed by several other functionally identical processors (the slaves). A trace-driven simulation program modeling this system was constructed, and was run with tracemore » output taken from two different simulation programs. Output from this simulation suggests that a significant reduction in run time may be realized by this approach. Sensitivity analysis was performed on the significant parameters to the system (number of slave processors, relative processor speeds, and interprocessor communication times). A comparison between actual and simulation run times for a one-processor system was used to assist in the validation of the simulation. 7 references.« less

Reducing The Risk Of Fires In Conveyor Transport

NASA Astrophysics Data System (ADS)

Cheremushkina, M. S.; Poddubniy, D. A.

2017-01-01

The paper deals with the actual problem of increasing the safety of operation of belt conveyors in mines. Was developed the control algorithm that meets the technical requirements of the mine belt conveyors, reduces the risk of fires of conveyors belt, and enables energy and resource savings taking into account random sort of traffic. The most effective method of decision such tasks is the construction of control systems with the use of variable speed drives for asynchronous motors. Was designed the mathematical model of the system "variable speed multiengine drive - conveyor - control system of conveyors", that takes into account the dynamic processes occurring in the elements of the transport system, provides an assessment of the energy efficiency of application the developed algorithms, which allows to reduce the dynamic overload in the belt to (15-20)%.

Simplifying and speeding the management of intra-node cache coherence

DOEpatents

Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton on Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Phillip [Cortlandt Manor, NY; Hoenicke, Dirk [Ossining, NY; Ohmacht, Martin [Yorktown Heights, NY

2012-04-17

A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an area of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.

Accuracy of 2 activity monitors in detecting steps in people with stroke and traumatic brain injury.

PubMed

Fulk, George D; Combs, Stephanie A; Danks, Kelly A; Nirider, Coby D; Raja, Bhavana; Reisman, Darcy S

2014-02-01

Advances in sensor technologies and signal processing techniques provide a method to accurately measure walking activity in the home and community. Activity monitors geared toward consumer or patient use may be an alternative to more expensive monitors designed for research to measure stepping activity. The objective of this study was to examine the accuracy of 2 consumer/patient activity monitors, the Fitbit Ultra and the Nike+ Fuelband, in identifying stepping activity in people with stroke and traumatic brain injury (TBI). Secondarily, the study sought to compare the accuracy of these 2 activity monitors with that of the StepWatch Activity Monitor (SAM) and a pedometer, the Yamax Digi-Walker SW-701 pedometer (YDWP). A cross-sectional design was used for this study. People with chronic stroke and TBI wore the 4 activity monitors while they performed the Two-Minute Walk Test (2MWT), during which they were videotaped. Activity monitor estimated steps taken were compared with actual steps taken counted from videotape. Accuracy and agreement between activity monitor estimated steps and actual steps were examined using intraclass correlation coefficients (ICC [2,1]) and the Bland-Altman method. The SAM demonstrated the greatest accuracy (ICC [2,1]=.97, mean difference between actual steps and SAM estimated steps=4.7 steps) followed by the Fitbit Ultra (ICC [2,1]=.73, mean difference between actual steps and Fitbit Ultra estimated steps=-9.7 steps), the YDWP (ICC [2,1]=.42, mean difference between actual steps and YDWP estimated steps=-28.8 steps), and the Nike+ Fuelband (ICC [2,1]=.20, mean difference between actual steps and Nike+ Fuelband estimated steps=-66.2 steps). Walking activity was measured over a short distance in a closed environment, and participants were high functioning ambulators, with a mean gait speed of 0.93 m/s. The Fitbit Ultra may be a low-cost alternative to measure the stepping activity in level, predictable environments of people with stroke and TBI who can walk at speeds ≥0.58 m/s.

Two-stage light-gas magnetoplasma accelerator for hypervelocity impact simulation

NASA Astrophysics Data System (ADS)

Khramtsov, P. P.; Vasetskij, V. A.; Makhnach, A. I.; Grishenko, V. M.; Chernik, M. Yu; Shikh, I. A.; Doroshko, M. V.

2016-11-01

The development of macroparticles acceleration methods for high-speed impact simulation in a laboratory is an actual problem due to increasing of space flights duration and necessity of providing adequate spacecraft protection against micrometeoroid and space debris impacts. This paper presents results of experimental study of a two-stage light- gas magnetoplasma launcher for acceleration of a macroparticle, in which a coaxial plasma accelerator creates a shock wave in a high-pressure channel filled with light gas. Graphite and steel spheres with diameter of 2.5-4 mm were used as a projectile and were accelerated to the speed of 0.8-4.8 km/s. A launching of particle occurred in vacuum. For projectile velocity control the speed measuring method was developed. The error of this metod does not exceed 5%. The process of projectile flight from the barrel and the process of a particle collision with a target were registered by use of high-speed camera. The results of projectile collision with elements of meteoroid shielding are presented. In order to increase the projectile velocity, the high-pressure channel should be filled with hydrogen. However, we used helium in our experiments for safety reasons. Therefore, we can expect that the range of mass and velocity of the accelerated particles can be extended by use of hydrogen as an accelerating gas.

Insight into the Physical and Dynamical Processes that Control Rapid Increases in Total Flash Rate

NASA Technical Reports Server (NTRS)

Schultz, Christopher J.; Carey, Lawrence D.; Schultz, Elise V.; Blakeslee, Richard J.; Goodman, Steven J.

2015-01-01

Rapid increases in total lightning (also termed "lightning jumps") have been observed for many decades. Lightning jumps have been well correlated to severe and hazardous weather occurrence. The main focus of lightning jump work has been on the development of lightning algorithms to be used in real-time assessment of storm intensity. However, in these studies it is typically assumed that the updraft "increases" without direct measurements of the vertical motion, or specification of which updraft characteristic actually increases (e.g., average speed, maximum speed, or convective updraft volume). Therefore, an end-to-end physical and dynamical basis for coupling rapid increases in total flash rate to increases in updraft speed and volume must be understood in order to ultimately relate lightning occurrence to severe storm metrics. Herein, we use polarimetric, multi-Doppler, and lightning mapping array measurements to provide physical context as to why rapid increases in total lightning are closely tied to severe and hazardous weather.

Minimum-Cost Aircraft Descent Trajectories with a Constrained Altitude Profile

NASA Technical Reports Server (NTRS)

Wu, Minghong G.; Sadovsky, Alexander V.

2015-01-01

An analytical formula for solving the speed profile that accrues minimum cost during an aircraft descent with a constrained altitude profile is derived. The optimal speed profile first reaches a certain speed, called the minimum-cost speed, as quickly as possible using an appropriate extreme value of thrust. The speed profile then stays on the minimum-cost speed as long as possible, before switching to an extreme value of thrust for the rest of the descent. The formula is applied to an actual arrival route and its sensitivity to winds and airlines' business objectives is analyzed.

[Body composition and constitution: a constitutional syndrome (1st of 2 parts)].

PubMed

Terán Díaz, E

1999-04-01

Constitutional syndrome alters body constitution modifying (usually decreasing) two of its dimensions--weight and perimeters--by changing the composition of one, several or every body levels. Apart of the cause, the basic physiopathological process that characterizes this new syndrome is the amino acid mobilization from the muscle (proteolysis). As soon as fat loss has no consequence to the organism, proteolysis reduces the muscle mass and life is in danger. Actually, there is no effective treatment to improve the nitrogen balance by medication or hormones in speed catabolic states but it can also approach us to more proper therapeutics for these so frequent processes in clinic.

The FEM Simulation on End Mill of Plastic Doors and Windows Corner Cleaning Based on Deform-3D

NASA Astrophysics Data System (ADS)

Li, Guoping; Huang, Zhenyong; Wang, Xiaohui

2017-12-01

In the plastic doors and windows corner cleaning process, the rotating speed, the feed rate and the milling cutter diameter are the main factors that affect the efficiency and quality of the of corner cleaning. In this paper, SolidWorks will be used to establish the 3D model of end mills, and use Deform-3D to research the end mill milling process. And using orthogonal experiment design method to analyze the effect of rotating speed, the feed rate and the milling cutter diameter on the axial force variation, and to get the overall trend of axial force and the selection of various parameters according to the influence of axial force change. Finally, simulate milling experiment used to get the actual axial force data to verify the reliability of the FEM simulation model. And the conclusion obtained in this paper has important theoretical value in improving the plastic doors and windows corner cleaning efficiency and quality.

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

50 CFR 216.274 - Mitigation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... safe speed. Release of ordnance through cloud cover is prohibited: aircraft must be able to actually... would be used. These aircraft would be capable of flying at the slow safe speeds necessary to enable... patrol aircraft aircrews, and Anti-submarine Warfare (ASW)/Mine Warfare (MIW) helicopter crews shall...

Idle speed and fuel vapor recovery control system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orzel, D.V.

1993-06-01

A method for controlling idling speed of an engine via bypass throttle connected in parallel to a primary engine throttle and for controlling purge flow through a vapor recovery system into an air/fuel intake of the engine is described, comprising the steps of: positioning the bypass throttle to decrease any difference between a desired engine idle speed and actual engine idle speed; and decreasing the purge flow when said bypass throttle position is less than a preselected fraction of a maximum bypass throttle position.

E-16211

NASA Image and Video Library

1966-12-22

The HL-10 Lifting Body completes its first research flight with a landing on Rogers Dry Lake. Due to control problems, pilot Bruce Peterson had to land at a higher speed than originally planned in order to keep the vehicle under control. The actual touchdown speed was about 280 knots. This was 30 knots above the speed called for in the flight plan. The HL-10's first flight had lasted 3 minutes and 9 seconds.

Effects of optic flow on spontaneous overground walk-to-run transition.

PubMed

De Smet, Kristof; Malcolm, P; Lenoir, M; Segers, V; De Clercq, D

2009-03-01

Perturbations of optic flow can induce changes in walking speed since subjects modulate their speed with respect to the speed perceived from optic flow. The purpose of this study was to examine the effects of optic flow on steady-state as well as on non steady-state locomotion, i.e. on spontaneous overground walk-to-run transitions (WRT) during which subjects were able to accelerate in their preferred way. In this experiment, while subjects moved along a specially constructed hallway, a series of stripes projected on the side walls and ceiling were made to move backward (against the locomotion direction) at an absolute speed of -2 m s(-1) (condition B), or to move forward at an absolute speed of +2 m s(-1) (condition F), or to remain stationary (condition C). While condition B and condition F entailed a decrease and an increase in preferred walking speed, respectively, the spatiotemporal characteristics of the spontaneous walking acceleration prior to reaching WRT were not influenced by modified visual information. However, backward moving stripes induced a smaller speed increase when making the actual transition to running. As such, running speeds after making the WRT were lower in condition B. These results indicate that the walking acceleration prior to reaching the WRT is more robust against visual perturbations compared to walking at preferred walking speed. This could be due to a higher contribution from spinal control during the walking acceleration phase. However, the finding that subjects started to run at a lower running speed when experiencing an approaching optic flow faster than locomotion speed shows that the actual realization of the WRT is not totally independent of external cues.

Effect of Variation of Speed Limits on Intercity Bus Fuel Consumption, Coach and Driver Utilization, and Corporate Profitability

DOT National Transportation Integrated Search

1975-11-01

The effect of speed limit and passenger load on fuel consumption was determined using actual intercity buses with simulated passenger loads over different types of terrain. In addition to road tests, laboratory type measurements were made on four int...

Development of a Post-Processing Algorithm for Accurate Human Skull Profile Extraction via Ultrasonic Phased Arrays

NASA Astrophysics Data System (ADS)

Al-Ansary, Mariam Luay Y.

Ultrasound Imaging has been favored by clinicians for its safety, affordability, accessibility, and speed compared to other imaging modalities. However, the trade-offs to these benefits are a relatively lower image quality and interpretability, which can be addressed by, for example, post-processing methods. One particularly difficult imaging case is associated with the presence of a barrier, such as a human skull, with significantly different acoustical properties than the brain tissue as the target medium. Some methods were proposed in the literature to account for this structure if the skull's geometry is known. Measuring the skull's geometry is therefore an important task that requires attention. In this work, a new edge detection method for accurate human skull profile extraction via post-processing of ultrasonic A-Scans is introduced. This method, referred to as the Selective Echo Extraction algorithm, SEE, processes each A-Scan separately and determines the outermost and innermost boundaries of the skull by means of adaptive filtering. The method can also be used to determine the average attenuation coefficient of the skull. When applied to simulated B-Mode images of the skull profile, promising results were obtained. The profiles obtained from the proposed process in simulations were found to be within 0.15lambda +/- 0.11lambda or 0.09 +/- 0.07mm from the actual profiles. Experiments were also performed to test SEE on skull mimicking phantoms with major acoustical properties similar to those of the actual human skull. With experimental data, the profiles obtained with the proposed process were within 0.32lambda +/- 0.25lambda or 0.19 +/- 0.15mm from the actual profile.

Model-based diagnosis of large diesel engines based on angular speed variations of the crankshaft

NASA Astrophysics Data System (ADS)

Desbazeille, M.; Randall, R. B.; Guillet, F.; El Badaoui, M.; Hoisnard, C.

2010-07-01

This work aims at monitoring large diesel engines by analyzing the crankshaft angular speed variations. It focuses on a powerful 20-cylinder diesel engine with crankshaft natural frequencies within the operating speed range. First, the angular speed variations are modeled at the crankshaft free end. This includes modeling both the crankshaft dynamical behavior and the excitation torques. As the engine is very large, the first crankshaft torsional modes are in the low frequency range. A model with the assumption of a flexible crankshaft is required. The excitation torques depend on the in-cylinder pressure curve. The latter is modeled with a phenomenological model. Mechanical and combustion parameters of the model are optimized with the help of actual data. Then, an automated diagnosis based on an artificially intelligent system is proposed. Neural networks are used for pattern recognition of the angular speed waveforms in normal and faulty conditions. Reference patterns required in the training phase are computed with the model, calibrated using a small number of actual measurements. Promising results are obtained. An experimental fuel leakage fault is successfully diagnosed, including detection and localization of the faulty cylinder, as well as the approximation of the fault severity.

Reticles, write time, and the need for speed

NASA Astrophysics Data System (ADS)

Ackmann, Paul W.; Litt, Lloyd C.; Ning, Guo Xiang

2014-10-01

Historical data indicates reticle write times are increasing node-to-node. The cost of mask sets is increasing driven by the tighter requirements and more levels. The regular introduction of new generations of mask patterning tools with improved performance is unable to fully compensate for the increased data and complexity required. Write time is a primary metric that drives mask fabrication speed. Design (Raw data) is only the first step in the process and many interactions between mask and wafer technology such as OPC used, OPC efficiency for writers, fracture engines, and actual field size used drive total write time. Yield, technology, and inspection rules drive the remaining raw cycle time. Yield can be even more critical for speed of delivery as it drives re-writes and wasted time. While intrinsic process yield is important, repair capability is the reason mask delivery is still able to deliver 100% good reticles to the fab. Advanced nodes utilizing several layers of multiple patterning may require mask writer tool dedication to meet image placement specifications. This will increase the effective mask cycle time for a layer mask set and drive the need for additional mask write capability in order to deliver masks at the rate required by the wafer fab production schedules.

Comparison of pedometer and accelerometer accuracy under controlled conditions.

PubMed

Le Masurier, Guy C; Tudor-Locke, Catrine

2003-05-01

The purpose of this investigation was to compare the concurrent accuracy of the CSA accelerometer and the Yamax pedometer under two conditions: 1) on a treadmill at five different speeds and 2) riding in a motorized vehicle on paved roads. In study 1, motion sensor performance was evaluated against actual steps taken during 5-min bouts at five different treadmill walking speeds (54, 67, 80, 94, and 107 m.min-1). In study 2, performance was evaluated during a roundtrip (drive 1 and drive 2) motor vehicle travel on paved roads (total distance traveled was 32.6 km or 20.4 miles). Any steps detected during motor vehicle travel were considered error. In study 1, the Yamax pedometer detected significantly (P < 0.05) fewer steps than actually taken at the slowest treadmill speed (54 m.min-1). Further, the pedometer detected fewer steps than the accelerometer at this speed (75.4% vs 98.9%, P < 0.05). There were no differences between instruments compared with actual steps taken at all other walking speeds. In study 2, the CSA detected approximately 17-fold more erroneous steps than the pedometer (approximately 250 vs 15 steps for the total distance traveled, P < 0.05). The magnitude of the error (for either instrument) is not likely an important threat to the assessment of free-living ambulatory populations but may be a problem for pedometers when monitoring frail older adults with slow gaits. On the other hand, CSA accelerometers erroneously detect more nonsteps than the Yamax pedometer under typical motor vehicle traveling conditions. This threat to validity is likely only problematic when using the accelerometer to assess physical activity in sedentary individuals who travel extensively by motor vehicle.

Analysis of sensorless control of brushless DC motor using unknown input observer with different gains

NASA Astrophysics Data System (ADS)

Astik, Mitesh B.; Bhatt, Praghnesh; Bhalja, Bhavesh R.

2017-03-01

A sensorless control scheme based on an unknown input observer is presented in this paper in which back EMF of the Brushless DC Motor (BLDC) is continuously estimated from available line voltages and currents. During negative rotation of motor, actual and estimated speed fail to track the reference speed and if the corrective action is not taken by the observer, the motor goes into saturation. To overcome this problem, the speed estimation algorithm has been implemented in this paper to control the dynamic behavior of the motor during negative rotation. The Ackermans method was used to calculate the gains of an unknown input observer which is based on the appropriate choice of the eigenvalues in advance. The criteria to choose eigenvalue is to obtain a balance between faster convergence rate and the least noise level. Simulations have been carried out for different disturbances such as step changes in motor reference speed and load torque. The comparative simulation results clearly depict that the disturbance effects in actual and estimated responses minimizes as observer gain setting increases.

Spinning Disc Technology – Residence Time Distribution and Efficiency in Textile Wastewater Treatment Application

NASA Astrophysics Data System (ADS)

Iacob Tudose, E. T.; Zaharia, C.

2018-06-01

The spinning disc (SD) technology has received increased attention in the last years due to its enhanced fluid flow features resulting in improved property transfers. The actual study focuses on characterization of the flow within a spinning disc system based on experimental data used to establish the residence time distribution (RTD) and its dependence on the feeding liquid flowrate and the disc rotational speed. To obtain these data, an inert tracer (sodium chloride) was injected as a pulse input in the liquid stream entering the disc and the salt concentration of the liquid leaving the disc was continuously recorded. The obtained data indicate that an increase in the liquid flowrate from 10 L/h to 30 L/h determines a narrower RTD function. Also, at rotational speed of 200 rpm, the residence time distribution is broader than that for 500 rpm and 800 rpm. The RTD data suggest that depending on the needed flow characteristics, one can choose a certain flowrate and rotational speed domain for its application. Also, the SD technology was used to process textile wastewater treated with bentonite (as both coagulation and discoloration agent) in order to investigate whether the quality indicators such as the total suspended solid content, turbidity and discoloration, can be improved. The experimental results are promising since the discoloration and the removals of suspended solids attained values of over 40%, and respectively, 50 %, depending on the effluent flowrate (10 l/h and 30 L/h), and the disc rotational speed (200 rpm, 550 rpm and 850 rpm) without any other addition of chemicals, or initiation of other simultaneous treatment processes (e.g., advanced oxidative, or reductive, or biochemical processes). This recommends spinning disc technology as a suitable and promising tool to improve different wastewater characteristics.

Analysis Method of Friction Torque and Weld Interface Temperature during Friction Process of Steel Friction Welding

NASA Astrophysics Data System (ADS)

Kimura, Masaaki; Inoue, Haruo; Kusaka, Masahiro; Kaizu, Koichi; Fuji, Akiyoshi

This paper describes an analysis method of the friction torque and weld interface temperature during the friction process for steel friction welding. The joining mechanism model of the friction welding for the wear and seizure stages was constructed from the actual joining phenomena that were obtained by the experiment. The non-steady two-dimensional heat transfer analysis for the friction process was carried out by calculation with FEM code ANSYS. The contact pressure, heat generation quantity, and friction torque during the wear stage were calculated using the coefficient of friction, which was considered as the constant value. The thermal stress was included in the contact pressure. On the other hand, those values during the seizure stage were calculated by introducing the coefficient of seizure, which depended on the seizure temperature. The relationship between the seizure temperature and the relative speed at the weld interface in the seizure stage was determined using the experimental results. In addition, the contact pressure and heat generation quantity, which depended on the relative speed of the weld interface, were solved by taking the friction pressure, the relative speed and the yield strength of the base material into the computational conditions. The calculated friction torque and weld interface temperatures of a low carbon steel joint were equal to the experimental results when friction pressures were 30 and 90 MPa, friction speed was 27.5 s-1, and weld interface diameter was 12 mm. The calculation results of the initial peak torque and the elapsed time for initial peak torque were also equal to the experimental results under the same conditions. Furthermore, the calculation results of the initial peak torque and the elapsed time for initial peak torque at various friction pressures were equal to the experimental results.

Dynamic calibration and analysis of crack tip propagation in energetic materials using real-time radiography

NASA Astrophysics Data System (ADS)

Butt, Ali

Crack propagation in a solid rocket motor environment is difficult to measure directly. This experimental and analytical study evaluated the viability of real-time radiography for detecting bore regression and propellant crack propagation speed. The scope included the quantitative interpretation of crack tip velocity from simulated radiographic images of a burning, center-perforated grain and actual real-time radiographs taken on a rapid-prototyped model that dynamically produced the surface movements modeled in the simulation. The simplified motor simulation portrayed a bore crack that propagated radially at a speed that was 10 times the burning rate of the bore. Comparing the experimental image interpretation with the calibrated surface inputs, measurement accuracies were quantified. The average measurements of the bore radius were within 3% of the calibrated values with a maximum error of 7%. The crack tip speed could be characterized with image processing algorithms, but not with the dynamic calibration data. The laboratory data revealed that noise in the transmitted X-Ray intensity makes sensing the crack tip propagation using changes in the centerline transmitted intensity level impractical using the algorithms employed.

Trajectory Analysis Unveils Reelin's Role in the Directed Migration of Granule Cells in the Dentate Gyrus.

PubMed

Wang, Shaobo; Brunne, Bianka; Zhao, Shanting; Chai, Xuejun; Li, Jiawei; Lau, Jeremie; Failla, Antonio Virgilio; Zobiak, Bernd; Sibbe, Mirjam; Westbrook, Gary L; Lutz, David; Frotscher, Michael

2018-01-03

Reelin controls neuronal migration and layer formation. Previous studies in reeler mice deficient in Reelin focused on the result of the developmental process in fixed tissue sections. It has remained unclear whether Reelin affects the migratory process, migration directionality, or migrating neurons guided by the radial glial scaffold. Moreover, Reelin has been regarded as an attractive signal because newly generated neurons migrate toward the Reelin-containing marginal zone. Conversely, Reelin might be a stop signal because migrating neurons in reeler , but not in wild-type mice, invade the marginal zone. Here, we monitored the migration of newly generated proopiomelanocortin-EGFP -expressing dentate granule cells in slice cultures from reeler , reeler -like mutants and wild-type mice of either sex using real-time microscopy. We discovered that not the actual migratory process and migratory speed, but migration directionality of the granule cells is controlled by Reelin. While wild-type granule cells migrated toward the marginal zone of the dentate gyrus, neurons in cultures from reeler and reeler -like mutants migrated randomly in all directions as revealed by vector analyses of migratory trajectories. Moreover, live imaging of granule cells in reeler slices cocultured to wild-type dentate gyrus showed that the reeler neurons changed their directions and migrated toward the Reelin-containing marginal zone of the wild-type culture, thus forming a compact granule cell layer. In contrast, directed migration was not observed when Reelin was ubiquitously present in the medium of reeler slices. These results indicate that topographically administered Reelin controls the formation of a granule cell layer. SIGNIFICANCE STATEMENT Neuronal migration and the various factors controlling its onset, speed, directionality, and arrest are poorly understood. Slice cultures offer a unique model to study the migration of individual neurons in an almost natural environment. In the present study, we took advantage of the expression of proopiomelanocortin-EGFP by newly generated, migrating granule cells to analyze their migratory trajectories in hippocampal slice cultures from wild-type mice and mutants deficient in Reelin signaling. We show that the compartmentalized presence of Reelin is essential for the directionality, but not the actual migratory process or speed, of migrating granule cells leading to their characteristic lamination in the dentate gyrus. Copyright © 2018 the authors 0270-6474/18/380137-12$15.00/0.

Driving on urban roads: How we come to expect the 'correct' speed.

PubMed

Charlton, Samuel G; Starkey, Nicola J

2017-11-01

The subjective categories that drivers use to distinguish between different road types have been shown to influence the speeds they choose to drive but as yet we do not understand the road features that drivers use to make their discriminations. To better understand how drivers describe and categorise the roads they drive, 55 participants were recruited to drive a video of familiar urban roads in a driving simulator at the speed they would drive these roads in their own cars (using the accelerator and brake pedal in the driving simulator to adjust their speed). The participants were then asked to sort photos of the roads they had just driven into piles so that their driving would be the same on all roads in one pile but different to the other piles. Finally, they answered a series of questions about each road to indicate what speed they would drive, the safe speed for the road, their speed limit belief as well as providing ratings of comfort, difficulty and familiarity. Overall, drivers' categorisation of roads was informed by a number of factors including speed limit belief, road features and markings (including medians), road width, and presence of houses, driveways and footpaths. The participants' categories were congruent with what they thought the speed limits were, but not necessarily the actual speed limits. Mismatches between actual speed limits and speed limit beliefs appeared to result from category-level expectations about speed limits that took precedence over recent experience in the simulator. Roads that historically had a 50km/h speed limit but had been reduced to 40km/h were still regarded as 50km/h roads by the participants, underscoring the point that simply posting a sign with a lower speed limit is not enough to overcome drivers' expectations and habits associated with the visual appearance of a road. The findings provided insights into how drivers view and categorise roads, and identify specific areas that could be used to improve speed limit credibility. Copyright © 2017 Elsevier Ltd. All rights reserved.

A noncontact laser technique for circular contouring accuracy measurement

NASA Astrophysics Data System (ADS)

Wang, Charles; Griffin, Bob

2001-02-01

The worldwide competition in manufacturing frequently requires the high-speed machine tools to deliver contouring accuracy in the order of a few micrometers, while moving at relatively high feed rates. Traditional test equipment is rather limited in its capability to measure contours of small radius at high speed. Described here is a new noncontact laser measurement technique for the test of circular contouring accuracy. This technique is based on a single-aperture laser Doppler displacement meter with a flat mirror as the target. It is of a noncontact type with the ability to vary the circular path radius continuously at data rates of up to 1000 Hz. Using this instrument, the actual radius, feed rate, velocity, and acceleration profiles can also be determined. The basic theory of operation, the hardware setup, the data collection, the data processing, and the error budget are discussed.

Ultra-fast underwater suction traps.

PubMed

Vincent, Olivier; Weisskopf, Carmen; Poppinga, Simon; Masselter, Tom; Speck, Thomas; Joyeux, Marc; Quilliet, Catherine; Marmottant, Philippe

2011-10-07

Carnivorous aquatic Utricularia species catch small prey animals using millimetre-sized underwater suction traps, which have fascinated scientists since Darwin's early work on carnivorous plants. Suction takes place after mechanical triggering and is owing to a release of stored elastic energy in the trap body accompanied by a very fast opening and closing of a trapdoor, which otherwise closes the trap entrance watertight. The exceptional trapping speed--far above human visual perception--impeded profound investigations until now. Using high-speed video imaging and special microscopy techniques, we obtained fully time-resolved recordings of the door movement. We found that this unique trapping mechanism conducts suction in less than a millisecond and therefore ranks among the fastest plant movements known. Fluid acceleration reaches very high values, leaving little chance for prey animals to escape. We discovered that the door deformation is morphologically predetermined, and actually performs a buckling/unbuckling process, including a complete trapdoor curvature inversion. This process, which we predict using dynamical simulations and simple theoretical models, is highly reproducible: the traps are autonomously repetitive as they fire spontaneously after 5-20 h and reset actively to their ready-to-catch condition.

The research of laser marking control technology

NASA Astrophysics Data System (ADS)

Zhang, Qiue; Zhang, Rong

2009-08-01

In the area of Laser marking, the general control method is insert control card to computer's mother board, it can not support hot swap, it is difficult to assemble or it. Moreover, the one marking system must to equip one computer. In the system marking, the computer can not to do the other things except to transmit marking digital information. Otherwise it can affect marking precision. Based on traditional control methods existed some problems, introduced marking graphic editing and digital processing by the computer finish, high-speed digital signal processor (DSP) control marking the whole process. The laser marking controller is mainly contain DSP2812, digital memorizer, DAC (digital analog converting) transform unit circuit, USB interface control circuit, man-machine interface circuit, and other logic control circuit. Download the marking information which is processed by computer to U disk, DSP read the information by USB interface on time, then processing it, adopt the DSP inter timer control the marking time sequence, output the scanner control signal by D/A parts. Apply the technology can realize marking offline, thereby reduce the product cost, increase the product efficiency. The system have good effect in actual unit markings, the marking speed is more quickly than PCI control card to 20 percent. It has application value in practicality.

Is there really an eccentric action of the hamstrings during the swing phase of high-speed running? Part II: Implications for exercise.

PubMed

Van Hooren, Bas; Bosch, Frans

2017-12-01

We have previously argued that there may actually be no significant eccentric, but rather predominantly an isometric action of the hamstring muscle fibres during the swing phase of high-speed running when the attachment points of the hamstrings are moving apart. Based on this we suggested that isometric rather than eccentric exercises are a more specific way of conditioning the hamstrings for high-speed running. In this review we argue that some of the presumed beneficial adaptations following eccentric training may actually not be related to the eccentric muscle fibre action, but to other factors such as exercise intensity. Furthermore, we discuss several disadvantages associated with commonly used eccentric hamstring exercises. Subsequently, we argue that high-intensity isometric exercises in which the series elastic element stretches and recoils may be equally or even more effective at conditioning the hamstrings for high-speed running, since they also avoid some of the negative side effects associated with eccentric training. We provide several criteria that exercises should fulfil to effectively condition the hamstrings for high-speed running. Adherence to these criteria will guarantee specificity with regards to hamstrings functioning during running. Practical examples of isometric exercises that likely meet several criteria are provided.

The Impact of Variable Wind Shear Coefficients on Risk Reduction of Wind Energy Projects

PubMed Central

Thomson, Allan; Yoonesi, Behrang; McNutt, Josiah

2016-01-01

Estimation of wind speed at proposed hub heights is typically achieved using a wind shear exponent or wind shear coefficient (WSC), variation in wind speed as a function of height. The WSC is subject to temporal variation at low and high frequencies, ranging from diurnal and seasonal variations to disturbance caused by weather patterns; however, in many cases, it is assumed that the WSC remains constant. This assumption creates significant error in resource assessment, increasing uncertainty in projects and potentially significantly impacting the ability to control gird connected wind generators. This paper contributes to the body of knowledge relating to the evaluation and assessment of wind speed, with particular emphasis on the development of techniques to improve the accuracy of estimated wind speed above measurement height. It presents an evaluation of the use of a variable wind shear coefficient methodology based on a distribution of wind shear coefficients which have been implemented in real time. The results indicate that a VWSC provides a more accurate estimate of wind at hub height, ranging from 41% to 4% reduction in root mean squared error (RMSE) between predicted and actual wind speeds when using a variable wind shear coefficient at heights ranging from 33% to 100% above the highest actual wind measurement. PMID:27872898

Description and test results of a variable speed, constant frequency generating system

NASA Astrophysics Data System (ADS)

Brady, F. J.

1985-12-01

The variable-speed, constant frequency generating system developed for the Mod-0 wind turbine is presented. This report describes the system as it existed at the conclusion of the project. The cycloconverter control circuit is described including the addition of field-oriented control. The laboratory test and actual wind turbine test results are included.

Measuring Second Language Vocabulary Knowledge Using a Temporal Method

ERIC Educational Resources Information Center

Tanabe, Masayuki

2016-01-01

The present study addressed the role of speed as a factor in tests of second language (L2) vocabulary knowledge, presupposing that speed of performance is important in actual language use. Research questions were: (a) Do learners with a larger vocabulary size answer faster on an L2 vocabulary breadth test than smaller vocabulary sized learners?;…

An Application Of High-Speed Photography To The Real Ignition Course Of Composite Propellants

NASA Astrophysics Data System (ADS)

Fusheng, Zhang; Gongshan, Cheng; Yong, Zhang; Fengchun, Li; Fanpei, Lei

1989-06-01

That the actual solid rocket motor behavior and delay time of the ignition of Ap/HTPB composite propellant ignited by high energy pyrotechics contained condensed particles have been investigated is the key of this paper. In experiments, using high speed camera, the pressure transducer, the photodiode and synchro circuit control system designed by us synchronistically observe and record all course and details of the ignition. And pressure signal, photodiode signal and high speed photography frame are corresponded one by one.

Himawari-8 Satellite Based Dynamic Monitoring of Grassland Fire in China-Mongolia Border Regions

PubMed Central

Na, Li; Bao, Yulong; Bao, Yongbin; Na, Risu; Tong, Siqin; Si, Alu

2018-01-01

In this study, we used bands 7, 4, and 3 of the Advance Himawari Imager (AHI) data, combined with a Threshold Algorithm and a visual interpretation method to monitor the entire process of grassland fires that occurred on the China-Mongolia border regions, between 05:40 (UTC) on April 19th to 13:50 (UTC) on April 21st 2016. The results of the AHI data monitoring are evaluated by the fire point product data, the wind field data, and the environmental information data of the area in which the fire took place. The monitoring result shows that, the grassland fire burned for two days and eight hours with a total burned area of about 2708.29 km2. It mainly spread from the northwest to the southeast, with a maximum burning speed of 20.9 m/s, a minimum speed of 2.52 m/s, and an average speed of about 12.07 m/s. Thus, using AHI data can not only quickly and accurately track the dynamic development of a grassland fire, but also estimate the spread speed and direction. The evaluation of fire monitoring results reveals that AHI data with high precision and timeliness can be highly consistent with the actual situation. PMID:29346289

The preferred walk to run transition speed in actual lunar gravity.

PubMed

De Witt, John K; Edwards, W Brent; Scott-Pandorf, Melissa M; Norcross, Jason R; Gernhardt, Michael L

2014-09-15

Quantifying the preferred transition speed (PTS) from walking to running has provided insight into the underlying mechanics of locomotion. The dynamic similarity hypothesis suggests that the PTS should occur at the same Froude number across gravitational environments. In normal Earth gravity, the PTS occurs at a Froude number of 0.5 in adult humans, but previous reports found the PTS occurred at Froude numbers greater than 0.5 in simulated lunar gravity. Our purpose was to (1) determine the Froude number at the PTS in actual lunar gravity during parabolic flight and (2) compare it with the Froude number at the PTS in simulated lunar gravity during overhead suspension. We observed that Froude numbers at the PTS in actual lunar gravity (1.39±0.45) and simulated lunar gravity (1.11±0.26) were much greater than 0.5. Froude numbers at the PTS above 1.0 suggest that the use of the inverted pendulum model may not necessarily be valid in actual lunar gravity and that earlier findings in simulated reduced gravity are more accurate than previously thought. © 2014. Published by The Company of Biologists Ltd.

Effects of the water level on the flow topology over the Bolund island

NASA Astrophysics Data System (ADS)

Cuerva-Tejero, A.; Yeow, T. S.; Gallego-Castillo, C.; Lopez-Garcia, O.

2014-06-01

We have analyzed the influence of the actual height of Bolund island above water level on different full-scale statistics of the velocity field over the peninsula. Our analysis is focused on the database of 10-minute statistics provided by Risø-DTU for the Bolund Blind Experiment. We have considered 10-minut.e periods with near-neutral atmospheric conditions, mean wind speed values in the interval [5,20] m/s, and westerly wind directions. As expected, statistics such as speed-up, normalized increase of turbulent kinetic energy and probability of recirculating flow show a large dependence on the emerged height of the island for the locations close to the escarpment. For the published ensemble mean values of speed-up and normalized increase of turbulent kinetic energy in these locations, we propose that some ammount of uncertainty could be explained as a deterministic dependence of the flow field statistics upon the actual height of the Bolund island above the sea level.

Use of simulated experiments for material characterization of brittle materials subjected to high strain rate dynamic tension

PubMed Central

Saletti, Dominique

2017-01-01

Rapid progress in ultra-high-speed imaging has allowed material properties to be studied at high strain rates by applying full-field measurements and inverse identification methods. Nevertheless, the sensitivity of these techniques still requires a better understanding, since various extrinsic factors present during an actual experiment make it difficult to separate different sources of errors that can significantly affect the quality of the identified results. This study presents a methodology using simulated experiments to investigate the accuracy of the so-called spalling technique (used to study tensile properties of concrete subjected to high strain rates) by numerically simulating the entire identification process. The experimental technique uses the virtual fields method and the grid method. The methodology consists of reproducing the recording process of an ultra-high-speed camera by generating sequences of synthetically deformed images of a sample surface, which are then analysed using the standard tools. The investigation of the uncertainty of the identified parameters, such as Young's modulus along with the stress–strain constitutive response, is addressed by introducing the most significant user-dependent parameters (i.e. acquisition speed, camera dynamic range, grid sampling, blurring), proving that the used technique can be an effective tool for error investigation. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’. PMID:27956505

Integration, Testing, and Validation of a Small Hybrid-Electric Remotely-Piloted Aircraft

DTIC Science & Technology

2012-03-22

in the electronic speed controller during low speed operation, due to actual power losses as well as switching losses in the generation of the ...more general description and simply indicates a RPA that uses two (or more) forms of power to drive the propulsion system . In essentially all... The last switch was implemented specifically due to the nature of

A discussion on velocity-speed and their instruction

NASA Astrophysics Data System (ADS)

Yıldız, Ali

2016-04-01

This study was conducted to investigate how to teach velocity and speed effectively, with which activities and examples. Although they are different quantities, they are generally used in the same meaning. Study data and the quantities discussed were obtained from the examination of documents such as scientific articles and books about the instruction and they were examined by descriptive analysis approach. Expository instruction was supported with writing to learn activities and an approach actualized in seven stages was suggested so that velocity and speed could be understood at an anticipated level. At each stage, possible practices were explained; and especially at the fifth stage of the study, a detailed example on distance, displacement, velocity and speed promoted the understanding of presented quantities much more easily and correctly with their critical properties, thus students would be able to associate it with their prior knowledge. Moreover, it was anticipated based on these reasons that the example could be used as a tool to actualize permanent learning. At the last stage of the study, it was considered that having students write a letter and a summary to young respondents could support the practices in the previous stages, and also it would help promoting long-term retention of the learned concepts.

Power Smoothing and MPPT for Grid-connected Wind Power Generation with Doubly Fed Induction Generator

NASA Astrophysics Data System (ADS)

Kai, Takaaki; Tanaka, Yuji; Kaneda, Hirotoshi; Kobayashi, Daichi; Tanaka, Akio

Recently, doubly fed induction generator (DFIG) and synchronous generator are mostly applied for wind power generation, and variable speed control and power factor control are executed for high efficiently for wind energy capture and high quality for power system voltage. In variable speed control, a wind speed or a generator speed is used for maximum power point tracking. However, performances of a wind generation power fluctuation due to wind speed variation have not yet investigated for those controls. The authors discuss power smoothing by those controls for the DFIG inter-connected to 6.6kV distribution line. The performances are verified using power system simulation software PSCAD/EMTDC for actual wind speed data and are examined from an approximate equation of wind generation power fluctuation for wind speed variation.

Radiation Pressure Cooling as a Quantum Dynamical Process

NASA Astrophysics Data System (ADS)

He, Bing; Yang, Liu; Lin, Qing; Xiao, Min

2017-06-01

One of the most fundamental problems in optomechanical cooling is how small the thermal phonon number of a mechanical oscillator can be achieved under the radiation pressure of a proper cavity field. Different from previous theoretical predictions, which were based on an optomechanical system's time-independent steady states, we treat such cooling as a dynamical process of driving the mechanical oscillator from its initial thermal state, due to its thermal equilibrium with the environment, to a stabilized quantum state of higher purity. We find that the stabilized thermal phonon number left in the end actually depends on how fast the cooling process could be. The cooling speed is decided by an effective optomechanical coupling intensity, which constitutes an essential parameter for cooling, in addition to the sideband resolution parameter that has been considered in other theoretical studies. The limiting thermal phonon number that any cooling process cannot surpass exhibits a discontinuous jump across a certain value of the parameter.

Fast thought speed induces risk taking.

PubMed

Chandler, Jesse J; Pronin, Emily

2012-04-01

In two experiments, we tested for a causal link between thought speed and risk taking. In Experiment 1, we manipulated thought speed by presenting neutral-content text at either a fast or a slow pace and having participants read the text aloud. In Experiment 2, we manipulated thought speed by presenting fast-, medium-, or slow-paced movie clips that contained similar content. Participants who were induced to think more quickly took more risks with actual money in Experiment 1 and reported greater intentions to engage in real-world risky behaviors, such as unprotected sex and illegal drug use, in Experiment 2. These experiments provide evidence that faster thinking induces greater risk taking.

Modeling Parasitic Energy Losses and the Impact of Advanced Tribological Concepts on Fuel Efficiency - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fenske, George

2016-11-28

Our primary task for this project was to perform FMEP calculations for a broad range of parameters including engine type [spark ignition (SI) or compression ignition (CI)], engine size, engine mode (speed and load), lubricant viscosity, asperity friction, surface finish, oil type (mineral or synthetic), and additive (friction modifier), as discussed previously [1–3]. The actual analysis was limited to a large diesel engine and it included both load and speed dependencies as well as lubricant viscosity and speed.

Evaluating transient performance of servo mechanisms by analysing stator current of PMSM

NASA Astrophysics Data System (ADS)

Zhang, Qing; Tan, Luyao; Xu, Guanghua

2018-02-01

Smooth running and rapid response are the desired performance goals for the transient motions of servo mechanisms. Because of the uncertain and unobservable transient behaviour of servo mechanisms, it is difficult to evaluate their transient performance. Under the effects of electromechanical coupling, the stator current signals of a permanent-magnet synchronous motor (PMSM) potentially contain the performance information regarding servo mechanisms in use. In this paper, a novel method based on analysing the stator current of the PMSM is proposed for quantifying the transient performance. First, a vector control model is constructed to simulate the stator current behaviour in the transient processes of consecutive speed changes, consecutive load changes, and intermittent start-stops. It is discovered that the amplitude and frequency of the stator current are modulated by the transient load torque and motor speed, respectively. The stator currents under different performance conditions are also simulated and compared. Then, the stator current is processed using a local means decomposition (LMD) algorithm to extract the instantaneous amplitude and instantaneous frequency. The sample entropy of the instantaneous amplitude, which reflects the complexity of the load torque variation, is calculated as a performance indicator of smooth running. The peak-to-peak value of the instantaneous frequency, which defines the range of the motor speed variation, is set as a performance indicator of rapid response. The proposed method is applied to both simulated data in an intermittent start-stops process and experimental data measured for a batch of servo turrets for turning lathes. The results show that the performance evaluations agree with the actual performance.

The neural speed of familiar face recognition.

PubMed

Barragan-Jason, G; Cauchoix, M; Barbeau, E J

2015-08-01

Rapidly recognizing familiar people from their faces appears critical for social interactions (e.g., to differentiate friend from foe). However, the actual speed at which the human brain can distinguish familiar from unknown faces still remains debated. In particular, it is not clear whether familiarity can be extracted from rapid face individualization or if it requires additional time consuming processing. We recorded scalp EEG activity in 28 subjects performing a go/no-go, famous/non-famous, unrepeated, face recognition task. Speed constraints were used to encourage subjects to use the earliest familiarity information available. Event related potential (ERP) analyses show that both the N170 and the N250 components were modulated by familiarity. The N170 modulation was related to behaviour: subjects presenting the strongest N170 modulation were also faster but less accurate than those who only showed weak N170 modulation. A complementary Multi-Variate Pattern Analysis (MVPA) confirmed ERP results and provided some more insights into the dynamics of face recognition as the N170 differential effect appeared to be related to a first transitory phase (transitory bump of decoding power) starting at around 140 ms, which returned to baseline afterwards. This bump of activity was henceforth followed by an increase of decoding power starting around 200 ms after stimulus onset. Overall, our results suggest that rather than a simple single-process, familiarity for faces may rely on a cascade of neural processes, including a coarse and fast stage starting at 140 ms and a more refined but slower stage occurring after 200 ms. Copyright © 2015 Elsevier Ltd. All rights reserved.

Speed of mental processing in the middle of the night

NASA Technical Reports Server (NTRS)

Monk, T. H.; Carrier, J.

1997-01-01

This study aimed to determine whether human mental processing actually slows down during the night hours, separately from the previously documented microsleeps, lapses in attention, and general slowing of motor responses. Eighteen healthy young adults were studied during 36 hours of constant wakeful bedrest. Every 2 hours, they performed a logical reasoning task. Items phrased in the negative voice took reliably longer to respond to than items phrased in the positive voice, indicating the need for more mental processing in those items. By subtracting "negative" from "positive" reaction times at each time of day, we were able to plot a circadian rhythm in the time taken for this extra mental processing to be done separately from microsleeps, psychomotor slowing, and inattention. The extra mental processing took longer at night and on the day following sleep loss than it did during the day before the sleep loss, suggesting that human mental processing slows down during the night under sleep deprivation.

Study on Stability of High Speed Traction Drive CVT for Aircraft Generator

NASA Astrophysics Data System (ADS)

Goi, Tatsuhiko; Tanaka, Hirohisa; Nakashima, Kenichi; Watanabe, Koji

A half-toroidal traction drive CVT has a feature of small spin at traction pitch in whole speed ratio range of 1:4, which suits to transmit high rotational speed with minimum temperature increase of traction surface. Research activity on traction drive CVT has commenced in 1996 for applying it to an aircraft 24,000rpm constant-speed generator instead of a hydro-static transmission. This paper shows fundamental design of 90kW traction drive integrated drive generator, ``T-IDG", and stability analysis on a sensor-less electro-hydraulic speed control servo-mechanism by bond graphs. The performance test of T-IDG mounted on a test bench and an actual jet engine proved that the control system using sensor-less servomechanism can keep the generator speed within MIL-STD-704E allowable limit against steep changes of speed and load.

Propeller thrust analysis using Prandtl's lifting line theory, a comparison between the experimental thrust and the thrust predicted by Prandtl's lifting line theory

NASA Astrophysics Data System (ADS)

Kesler, Steven R.

The lifting line theory was first developed by Prandtl and was used primarily on analysis of airplane wings. Though the theory is about one hundred years old, it is still used in the initial calculations to find the lift of a wing. The question that guided this thesis was, "How close does Prandtl's lifting line theory predict the thrust of a propeller?" In order to answer this question, an experiment was designed that measured the thrust of a propeller for different speeds. The measured thrust was compared to what the theory predicted. In order to do this experiment and analysis, a propeller needed to be used. A walnut wood ultralight propeller was chosen that had a 1.30 meter (51 inches) length from tip to tip. In this thesis, Prandtl's lifting line theory was modified to account for the different incoming velocity depending on the radial position of the airfoil. A modified equation was used to reflect these differences. A working code was developed based on this modified equation. A testing rig was built that allowed the propeller to be rotated at high speeds while measuring the thrust. During testing, the rotational speed of the propeller ranged from 13-43 rotations per second. The thrust from the propeller was measured at different speeds and ranged from 16-33 Newton's. The test data were then compared to the theoretical results obtained from the lifting line code. A plot in Chapter 5 (the results section) shows the theoretical vs. actual thrust for different rotational speeds. The theory over predicted the actual thrust of the propeller. Depending on the rotational speed, the error was: at low speeds 36%, at low to moderate speeds 84%, and at high speeds the error increased to 195%. Different reasons for these errors are discussed.

Study of Dimple Effect on the Friction Characteristics of a Journal Bearing using Taguchi Method

NASA Astrophysics Data System (ADS)

Murthy, A. Amar; Raghunandana, Dr.

2018-02-01

The effect of producing dimples using chemically etched techniques or by machining process on the surface of a journal bearing bushing to reduce the friction using Taguchi method is investigated. The data used in the present analysis is based on the results obtained by the series of experiments conducted to study the dimples effect on the Stribeck curve. It is statistically proved that producing dimples on the bushing surface of a journal bearing has significant effect on the friction coefficient when used with light oils. Also it is seen that there is an interaction effect between speeds-load and load-dimples. Hence the interaction effect, which are usually neglected should be considered during actual experiments that significantly contributes in reducing the friction in mixed lubrication regime. The experiments, if were conducted after Taguchi method, then the number of experiments would have been reduced to half of the actual set of experiments that were essentially conducted.

Estimating TCP Packet Loss Ratio from Sampled ACK Packets

NASA Astrophysics Data System (ADS)

Yamasaki, Yasuhiro; Shimonishi, Hideyuki; Murase, Tutomu

The advent of various quality-sensitive applications has greatly changed the requirements for IP network management and made the monitoring of individual traffic flows more important. Since the processing costs of per-flow quality monitoring are high, especially in high-speed backbone links, packet sampling techniques have been attracting considerable attention. Existing sampling techniques, such as those used in Sampled NetFlow and sFlow, however, focus on the monitoring of traffic volume, and there has been little discussion of the monitoring of such quality indexes as packet loss ratio. In this paper we propose a method for estimating, from sampled packets, packet loss ratios in individual TCP sessions. It detects packet loss events by monitoring duplicate ACK events raised by each TCP receiver. Because sampling reveals only a portion of the actual packet loss, the actual packet loss ratio is estimated statistically. Simulation results show that the proposed method can estimate the TCP packet loss ratio accurately from a 10% sampling of packets.

ISACS-DOC: Monitoring and Diagnostic System for AKARI and HINODE

NASA Astrophysics Data System (ADS)

Mizutani, Mitsue; Hirose, Toshinori; Takaki, Ryoji; Honda, Hideyuki

ISACS-DOC (Intelligent Satellite Control Software-DOCtor), which is an automatic monitoring and diagnostic system for scientific satellites or spacecraft, aims to rapidly and accurately capture important changes and sign of anomaly during daily satellite operations. After three systems for deep space missions, the new generation of ISACS-DOC with a higher speed processing performance had been developed for the satellites in earth orbit, AKARI and HINODE. This paper reports on the newest ISACS-DOC about enhanced functions, operating status, and an approach to create standards to build and keep up the knowledge data base. Continuous enhancements through the actual operations are the advantage of ISACS-DOC.

Typing pictures: Linguistic processing cascades into finger movements.

PubMed

Scaltritti, Michele; Arfé, Barbara; Torrance, Mark; Peressotti, Francesca

2016-11-01

The present study investigated the effect of psycholinguistic variables on measures of response latency and mean interkeystroke interval in a typewritten picture naming task, with the aim to outline the functional organization of the stages of cognitive processing and response execution associated with typewritten word production. Onset latencies were modulated by lexical and semantic variables traditionally linked to lexical retrieval, such as word frequency, age of acquisition, and naming agreement. Orthographic variables, both at the lexical and sublexical level, appear to influence just within-word interkeystroke intervals, suggesting that orthographic information may play a relevant role in controlling actual response execution. Lexical-semantic variables also influenced speed of execution. This points towards cascaded flow of activation between stages of lexical access and response execution. Copyright © 2016 Elsevier B.V. All rights reserved.

Optical Sensors Based on Single Arm Thin Film Waveguide Interferometer

NASA Technical Reports Server (NTRS)

Sarkisov, Sergey S.

1997-01-01

All the goals of the research effort for the first year were met by the accomplishments. Additional efforts were done to speed up the process of development and construction of the experimental gas chamber which will be completed by the end of 1997. This chamber incorporates vacuum sealed multimode optical fiber lines which connect the sensor to the remote light source and signal processing equipment. This optical fiber line is a prototype of actual optical communication links connecting real sensors to a control unit within an aircraft or spacecraft. An important problem which we are planning to focus on during the second year is coupling of optical fiber line to the sensor. Currently this problem is solved using focusing optics and prism couplers. More reliable solutions are planned to be investigated.

Modelling the Peak Elongation of Nylon6 and Fe Powder Based Composite Wire for FDM Feedstock Filament

NASA Astrophysics Data System (ADS)

Garg, Harish Kumar; Singh, Rupinder

2017-10-01

In the present work, to increase the application domain of fused deposition modelling (FDM) process, Nylon6-Fe powder based composite wire has been prepared as feed stock filament. Further for smooth functioning of feed stock filament without any change in the hardware and software of the commercial FDM setup, the mechanical properties of the newly prepared composite wire must be comparable/at par to the existing material i.e. ABS, P-430. So, keeping this in consideration; an effort has been made to model the peak elongation of in house developed feedstock filament comprising of Nylon6 and Fe powder (prepared on single screw extrusion process) for commercial FDM setup. The input parameters of single screw extruder (namely: barrel temperature, temperature of the die, speed of the screw, speed of the winding machine) and rheological property of material (melt flow index) has been modelled with peak elongation as the output by using response surface methodology. For validation of model the result of peak elongation obtained from the model equation the comparison was made with the results of actual experimentation which shows the variation of ±1 % only.

Development of an on-site rapid real-time polymerase chain reaction system and the characterization of suitable DNA polymerases for TaqMan probe technology.

PubMed

Furutani, Shunsuke; Naruishi, Nahoko; Hagihara, Yoshihisa; Nagai, Hidenori

2016-08-01

On-site quantitative analyses of microorganisms (including viruses) by the polymerase chain reaction (PCR) system are significantly influencing medical and biological research. We have developed a remarkably rapid and portable real-time PCR system that is based on microfluidic approaches. Real-time PCR using TaqMan probes consists of a complex reaction. Therefore, in a rapid real-time PCR, the optimum DNA polymerase must be estimated by using actual real-time PCR conditions. In this study, we compared the performance of three DNA polymerases in actual PCR conditions using our rapid real-time PCR system. Although KAPA2G Fast HS DNA Polymerase has the highest enzymatic activity among them, SpeedSTAR HS DNA Polymerase exhibited better performance to rapidly increase the fluorescence signal in an actual real-time PCR using TaqMan probes. Furthermore, we achieved rapid detection of Escherichia coli in 7 min by using SpeedSTAR HS DNA Polymerase with the same sensitivity as that of a conventional thermal cycler.

Detecting the crankshaft torsional vibration of diesel engines for combustion related diagnosis

NASA Astrophysics Data System (ADS)

Charles, P.; Sinha, Jyoti K.; Gu, F.; Lidstone, L.; Ball, A. D.

2009-04-01

Early fault detection and diagnosis for medium-speed diesel engines is important to ensure reliable operation throughout the course of their service. This work presents an investigation of the diesel engine combustion related fault detection capability of crankshaft torsional vibration. The encoder signal, often used for shaft speed measurement, has been used to construct the instantaneous angular speed (IAS) waveform, which actually represents the signature of the torsional vibration. Earlier studies have shown that the IAS signal and its fast Fourier transform (FFT) analysis are effective for monitoring engines with less than eight cylinders. The applicability to medium-speed engines, however, is strongly contested due to the high number of cylinders and large moment of inertia. Therefore the effectiveness of the FFT-based approach has further been enhanced by improving the signal processing to determine the IAS signal and subsequently tested on a 16-cylinder engine. In addition, a novel method of presentation, based on the polar coordinate system of the IAS signal, has also been introduced; to improve the discrimination features of the faults compared to the FFT-based approach of the IAS signal. The paper discusses two typical experimental studies on 16- and 20-cylinder engines, with and without faults, and the diagnosis results by the proposed polar presentation method. The results were also compared with the earlier FFT-based method of the IAS signal.

Efficiency improvement of technological preparation of power equipment manufacturing

NASA Astrophysics Data System (ADS)

Milukov, I. A.; Rogalev, A. N.; Sokolov, V. P.; Shevchenko, I. V.

2017-11-01

Competitiveness of power equipment primarily depends on speeding-up the development and mastering of new equipment samples and technologies, enhancement of organisation and management of design, manufacturing and operation. Actual political, technological and economic conditions cause the acute need in changing the strategy and tactics of process planning. At that the issues of maintenance of equipment with simultaneous improvement of its efficiency and compatibility to domestically produced components are considering. In order to solve these problems, using the systems of computer-aided process planning for process design at all stages of power equipment life cycle is economically viable. Computer-aided process planning is developed for the purpose of improvement of process planning by using mathematical methods and optimisation of design and management processes on the basis of CALS technologies, which allows for simultaneous process design, process planning organisation and management based on mathematical and physical modelling of interrelated design objects and production system. An integration of computer-aided systems providing the interaction of informative and material processes at all stages of product life cycle is proposed as effective solution to the challenges in new equipment design and process planning.

Surface Wind Field Analyses of Tropical Cyclones in the Western Pacific

DTIC Science & Technology

2012-09-01

Averaged vertical profiles of actual wind speeds (m s-1) from all dropwindsondes in three ITOP storms . (b) Averaged vertical profiles of wind speeds...for the entire set of winds from the three ITOP 2010 typhoons. .............................1  Figure 27.  a) Storm -relative motion flight track for...1  Figure 28.  a) Storm -relative motion flight track for flight 0420 in TY Fanapi

Sex differences in mate preferences revisited: do people know what they initially desire in a romantic partner?

PubMed

Eastwick, Paul W; Finkel, Eli J

2008-02-01

In paradigms in which participants state their ideal romantic-partner preferences or examine vignettes and photographs, men value physical attractiveness more than women do, and women value earning prospects more than men do. Yet it remains unclear if these preferences remain sex differentiated in predicting desire for real-life potential partners (i.e., individuals whom one has actually met). In the present study, the authors explored this possibility using speed dating and longitudinal follow-up procedures. Replicating previous research, participants exhibited traditional sex differences when stating the importance of physical attractiveness and earning prospects in an ideal partner and ideal speed date. However, data revealed no sex differences in the associations between participants' romantic interest in real-life potential partners (met during and outside of speed dating) and the attractiveness and earning prospects of those partners. Furthermore, participants' ideal preferences, assessed before the speed-dating event, failed to predict what inspired their actual desire at the event. Results are discussed within the context of R. E. Nisbett and T. D. Wilson's (1977) seminal article: Even regarding such a consequential aspect of mental life as romantic-partner preferences, people may lack introspective awareness of what influences their judgments and behavior. (c) 2008 APA, all rights reserved

Does insertion of intramuscular electromyographic electrodes alter motor behavior during locomotion?

PubMed

Armour Smith, Jo; Kulig, Kornelia

2015-06-01

Intramuscular electromyography (EMG) is commonly used to quantify activity in the trunk musculature. However, it is unclear if the discomfort or fear of pain associated with insertion of intramuscular EMG electrodes results in altered motor behavior. This study examined whether intramuscular EMG affects locomotor speed and trunk motion, and examined the anticipated and actual pain associated with electrode insertion in healthy individuals and individuals with a history of low back pain (LBP). Before and after insertion of intramuscular electrodes into the lumbar and thoracic paraspinals, participants performed multiple repetitions of a walking turn at self-selected and controlled average speed. Low levels of anticipated and actual pain were reported in both groups. Self-selected locomotor speed was significantly increased following insertion of the electrodes. At the controlled speed, the amplitude of sagittal plane lumbo-pelvic motion decreased significantly post-insertion, but the extent of this change was the same in both groups. Lumbo-pelvic motion in the frontal and axial planes and thoraco-lumbar motion in all planes were not affected by the insertions. This study demonstrates that intramuscular EMG is an appropriate methodology to selectively quantify the activation patterns of the individual muscles in the paraspinal group, both in healthy individuals and individuals with a history of LBP. Copyright © 2015 Elsevier Ltd. All rights reserved.

Judging arrival times of incoming traffic vehicles is not a prerequisite for safely crossing an intersection: Differential effects of vehicle size and type in passive judgment and active driving tasks.

PubMed

Mathieu, Julie; Bootsma, Reinoud J; Berthelon, Catherine; Montagne, Gilles

2017-02-01

Using a fixed-base driving simulator we compared the effects of the size and type of traffic vehicles (i.e., normal-sized or double-sized cars or motorcycles) approaching an intersection in two different tasks. In the perceptual judgment task, passively moving participants estimated when a traffic vehicle would reach the intersection for actual arrival times (ATs) of 1, 2, or 3s. In line with earlier findings, ATs were generally underestimated, the more so the longer the actual AT. Results revealed that vehicle size affected judgments in particular for the larger actual ATs (2 and 3s), with double-sized vehicles then being judged as arriving earlier than normal-sized vehicles. Vehicle type, on the other hand, affected judgments at the smaller actual ATs (1 and 2s), with cars then being judged as arriving earlier than motorcycles. In the behavioral task participants actively drove the simulator to cross the intersection by passing through a gap in a train of traffic. Analyses of the speed variations observed during the active intersection-crossing task revealed that the size and type of vehicles in the traffic train did not affect driving behavior in the same way as in the AT judgment task. First, effects were considerably smaller, affecting driving behavior only marginally. Second, effects were opposite to expectations based on AT judgments: driver approach speeds were smaller (rather than larger) when confronted with double-sized vehicles as compared to their normal-sized counterparts and when confronted with cars as compared to motorcycles. Finally, the temporality of the effects was different on the two tasks: vehicle size affected driver approach speed in the final stages of approach rather than early on, while vehicle type affected driver approach speed early on rather than later. Overall, we conclude that the active control of approach to the intersection is not based on successive judgments of traffic vehicle arrival times. These results thereby question the general belief that arrival time estimates are crucial for safe interaction with traffic. Copyright © 2016 Elsevier B.V. All rights reserved.

Theoretical and observational assessments of flare efficiencies.

PubMed

Leahey, D M; Preston, K; Strosher, M

2001-12-01

Flaring of waste gases is a common practice in the processing of hydrocarbon (HC) materials. It is assumed that flaring achieves complete combustion with relatively innocuous byproducts such as CO2 and H2O. However, flaring is rarely successful in the attainment of complete combustion, because entrainment of air into the region of combusting gases restricts flame sizes to less than optimum values. The resulting flames are too small to dissipate the amount of heat associated with 100% combustion efficiency. Equations were employed to estimate flame lengths, areas, and volumes as functions of flare stack exit velocity, stoichiometric mixing ratio, and wind speed. Heats released as part of the combustion process were then estimated from a knowledge of the flame dimensions together with an assumed flame temperature of 1200 K. Combustion efficiencies were subsequently obtained by taking the ratio of estimated actual heat release values to those associated with 100% complete combustion. Results of the calculations showed that combustion efficiencies decreased rapidly as wind speed increased from 1 to 6 m/sec. As wind speeds increased beyond 6 m/sec, combustion efficiencies tended to level off at values between 10 and 15%. Propane and ethane tend to burn more efficiently than do methane or hydrogen sulfide because of their lower stoichiometric mixing ratios. Results of theoretical predictions were compared to nine values of local combustion efficiencies obtained as part of an observational study into flaring activity conducted by the Alberta Research Council (ARC). All values were obtained during wind speed conditions of less than 4 m/sec. There was generally good agreement between predicted and observed values. The mean and standard deviation of observed combustion efficiencies were 68 +/- 7%. Comparable predicted values were 69 +/- 7%.

Super Mario's prison break —A proposal of object-intelligent-feedback-based classical Zeno and anti-Zeno effects

NASA Astrophysics Data System (ADS)

Gu, Shi-Jian

2009-10-01

Super Mario is imprisoned by a demon in a finite potential well on his way to save Princess Peach. He can escape from the well with the help of a flight of magic stairs floating in the space. However, the hateful demon may occasionally check his status. At that time, he has to make a judgement of either jumping to the inside ground immediately in order to avoid the discovery of his escape intention, or speeding up his escape process. Therefore, if the demon checks him too frequently such that there is no probability for him to reach the top of the barrier, he will be always inside the well, then a classical Zeno effect occurs. On the other hand, if the time interval between two subsequent checks is large enough such that he has a higher probability of being beyond the demon's controllable range already, then the demon's check actually speeds up his escape and a classical anti-Zeno effect takes place.

Adaptation of Combustion Principles to Aircraft Propulsion. Volume I; Basic Considerations in the Combustion of Hydrocarbon Fuels with Air

NASA Technical Reports Server (NTRS)

Barnett, Henry C (Editor); Hibbard, Robert R (Editor)

1955-01-01

The report summarizes source material on combustion for flight-propulsion engineers. First, several chapters review fundamental processes such as fuel-air mixture preparation, gas flow and mixing, flammability and ignition, flame propagation in both homogenous and heterogenous media, flame stabilization, combustion oscillations, and smoke and carbon formation. The practical significance and the relation of these processes to theory are presented. A second series of chapters describes the observed performance and design problems of engine combustors of the principal types. An attempt is made to interpret performance in terms of the fundamental processes and theories previously reviewed. Third, the design of high-speed combustion systems is discussed. Combustor design principles that can be established from basic considerations and from experience with actual combustors are described. Finally, future requirements for aircraft engine combustion systems are examined.

Low speed phaselock speed control system. [for brushless dc motor

NASA Technical Reports Server (NTRS)

Fulcher, R. W.; Sudey, J. (Inventor)

1975-01-01

A motor speed control system for an electronically commutated brushless dc motor is provided which includes a phaselock loop with bidirectional torque control for locking the frequency output of a high density encoder, responsive to actual speed conditions, to a reference frequency signal, corresponding to the desired speed. The system includes a phase comparator, which produces an output in accordance with the difference in phase between the reference and encoder frequency signals, and an integrator-digital-to-analog converter unit, which converts the comparator output into an analog error signal voltage. Compensation circuitry, including a biasing means, is provided to convert the analog error signal voltage to a bidirectional error signal voltage which is utilized by an absolute value amplifier, rotational decoder, power amplifier-commutators, and an arrangement of commutation circuitry.

A preliminary study of a running speed based heart rate prediction during an incremental treadmill exercise.

PubMed

Dae-Geun Jang; Byung-Hoon Ko; Sub Sunoo; Sang-Seok Nam; Hun-Young Park; Sang-Kon Bae

2016-08-01

This preliminary study investigates feasibility of a running speed based heart rate (HR) prediction. It is basically motivated from the assumption that there is a significant relationship between HR and the running speed. In order to verify the assumption, HR and running speed data from 217 subjects of varying aerobic capabilities were simultaneously collected during an incremental treadmill exercise. A running speed was defined as a treadmill speed and its corresponding heart rate was calculated by averaging the last one minute HR values of each session. The feasibility was investigated by assessing a correlation between the heart rate and the running speed using inter-subject (between-subject) and intra-subject (within-subject) datasets with regression orders of 1, 2, 3, and 4, respectively. Furthermore, HR differences between actual and predicted HRs were also employed to investigate the feasibility of the running speed in predicting heart rate. In the inter-subject analysis, a strong positive correlation and a reasonable HR difference (r = 0.866, 16.55±11.24 bpm @ 1st order; r = 0.871, 15.93±11.49 bpm @ 2nd order; r = 0.897, 13.98±10.80 bpm @ 3rd order; and r = 0.899, 13.93±10.64 bpm @ 4th order) were obtained, and a very high positive correlation and a very low HR difference (r = 0.978, 6.46±3.89 bpm @ 1st order; r = 0.987, 5.14±2.87 bpm @ 2nd order; r = 0.996, 2.61±2.03 bpm @ 3rd order; and r = 0.997, 2.04±1.73 bpm @ 4th order) were obtained in the intra-subject analysis. It can therefore be concluded that 1) heart rate is highly correlated with a running speed; 2) heart rate can be approximately estimated by a running speed with a proper statistical model (e.g., 3rd-order regression); and 3) an individual HR-speed calibration process may improve the prediction accuracy.

Impact of Diagnostic Practices on the Self-Reported Health of Mothers of Recently Diagnosed Children with ASD

PubMed Central

Reed, Phil; Picton, Lucy; Grainger, Nicole; Osborne, Lisa A.

2016-01-01

Objectives: Obtaining a diagnosis of an Autism Spectrum Disorder (ASD) for a child is a pivotal point in developing the treatment plan for the child but can also be regarded as highly stressful by parents. The current study examined the impact of different aspects of the diagnosis process on the self-reported mental health of mothers of children undergoing a diagnosis for ASD in a cross-sectional cohort design. Methods: One-hundred-fifty-eight mothers of consequently diagnosed children with ASD participated. The severity of the children’s ASD and their intellectual functioning was assessed within twelve months of the diagnosis, and the mothers completed a psychometric assessment battery including the Hospital Anxiety and Depression Scale, General Health Questionnaire, and Questionnaire on Resources and Stress. Results: The actual time from first reporting a problem to obtaining a diagnosis, and the speed of the diagnostic process from first to last appointment, were both negatively related to patenting stress. In contrast, mothers’ perceptions of the speed and helpfulness of the process were negatively related to levels of anxiety and depression. The number of professionals involved in the process and the perceived coherence of the diagnosis were also negatively related to aspects of mothers’ functioning. Conclusions: Care is needed to help mothers through the diagnostic process with regard to their own functioning. Providing information and help sources throughout the process, while keeping the number of professionals involved to a minimum, may improve the parent perception of the process and reduce the negative impacts of the diagnosis on the family as a whole. PMID:27618075

A new method to measure circular runout of end-milling spindle based on cutting mark

NASA Astrophysics Data System (ADS)

Zhou, Jianlai; Liu, Shuchun

2008-12-01

A practical method is introduced to measure the circular runout of a end-milling spindle system at high speed rotations without the need of a reference sphere. A workpiece is held on a linear slide which moves along the axial direction of the spindle. The spindle is then programmed to run at a specific speed. A very sharp edge cutter must be used and the depth of cut will be very shallow in order to keep the cutting force very small. The workpiece is then fed into the end mill in order to make a cutting mark of teens μm in depth. The cutting marks are circular, and their diameters are related to the circular runout of the spindle system. The cutting mark that is generated at a specific speed is expected to contain information about the spindle circular runout at this speed. In practice the cutting marks are not perfectly circular. Therefore, a best-fit circle of a cutting mark is needed to determine its diameter. A high-resolution edge detector machine is used for this purpose. Quantitative precision analysis was carried out to confirm the accuracy and repeatability of this new measurement technique. It is demonstrated that this technique for the measurement of spindle circular runout is an effective tool in verifying the actual running accuracy of spindles at their actual operating speeds and can be accomplished without the need for a reference sphere.

Comparing Perceptions and Measures of Congestion

DOT National Transportation Integrated Search

2012-10-01

Peoples perception of congestion and the actual measured congestion do not always agree. Measured : congestion relates to the delay resulting from field measurements of traffic volume, speed, and travel : time. Peoples perception of congestion ...

Better road congestion measures are needed

DOT National Transportation Integrated Search

2003-05-01

Road congestion is growing worse as demand : outstrips new roadway construction and other : efforts to increase traffic flows. : Better ways to measure congestion are needed to : effectively address the problem. : Actual measures of speeds an...

Influence of unbalance on the nonlinear dynamical response and stability of flexible rotor-bearing systems

NASA Technical Reports Server (NTRS)

Gunter, E. J.; Humphris, R. R.; Springer, H.

1983-01-01

In this paper, some of the effects of unbalance on the nonlinear response and stability of flexible rotor-bearing systems is presented from both a theoretical and experimental standpoint. In a linear system, operating above its stability threshold, the amplitude of motion grows exponentially with time and the orbits become unbounded. In an actual system, this is not necessarily the case. The actual amplitudes of motion may be bounded due to various nonlinear effects in the system. These nonlinear effects cause limit cycles of motion. Nonlinear effects are inherent in fluid film bearings and seals. Other contributors to nonlinear effects are shafts, couplings and foundations. In addition to affecting the threshold of stability, the nonlinear effects can cause jump phenomena to occur at not only the critical speeds, but also at stability onset or restabilization speeds.

Flight Management System Execution of Idle-Thrust Descents in Operations

NASA Technical Reports Server (NTRS)

Stell, Laurel L.

2011-01-01

To enable arriving aircraft to fly optimized descents computed by the flight management system (FMS) in congested airspace, ground automation must accurately predict descent trajectories. To support development of the trajectory predictor and its error models, commercial flights executed idle-thrust descents, and the recorded data includes the target speed profile and FMS intent trajectories. The FMS computes the intended descent path assuming idle thrust after top of descent (TOD), and any intervention by the controllers that alters the FMS execution of the descent is recorded so that such flights are discarded from the analysis. The horizontal flight path, cruise and meter fix altitudes, and actual TOD location are extracted from the radar data. Using more than 60 descents in Boeing 777 aircraft, the actual speeds are compared to the intended descent speed profile. In addition, three aspects of the accuracy of the FMS intent trajectory are analyzed: the meter fix crossing time, the TOD location, and the altitude at the meter fix. The actual TOD location is within 5 nmi of the intent location for over 95% of the descents. Roughly 90% of the time, the airspeed is within 0.01 of the target Mach number and within 10 KCAS of the target descent CAS, but the meter fix crossing time is only within 50 sec of the time computed by the FMS. Overall, the aircraft seem to be executing the descents as intended by the designers of the onboard automation.

Foggy perception slows us down.

PubMed

Pretto, Paolo; Bresciani, Jean-Pierre; Rainer, Gregor; Bülthoff, Heinrich H

2012-10-30

Visual speed is believed to be underestimated at low contrast, which has been proposed as an explanation of excessive driving speed in fog. Combining psychophysics measurements and driving simulation, we confirm that speed is underestimated when contrast is reduced uniformly for all objects of the visual scene independently of their distance from the viewer. However, we show that when contrast is reduced more for distant objects, as is the case in real fog, visual speed is actually overestimated, prompting drivers to decelerate. Using an artificial anti-fog-that is, fog characterized by better visibility for distant than for close objects, we demonstrate for the first time that perceived speed depends on the spatial distribution of contrast over the visual scene rather than the global level of contrast per se. Our results cast new light on how reduced visibility conditions affect perceived speed, providing important insight into the human visual system.DOI:http://dx.doi.org/10.7554/eLife.00031.001.

Influence of speed and step frequency during walking and running on motion sensor output.

PubMed

Rowlands, Ann V; Stone, Michelle R; Eston, Roger G

2007-04-01

Studies have reported strong linear relationships between accelerometer output and walking/running speeds up to 10 km x h(-1). However, ActiGraph uniaxial accelerometer counts plateau at higher speeds. The aim of this study was to determine the relationships of triaxial accelerometry, uniaxial accelerometry, and pedometry with speed and step frequency (SF) across a range of walking and running speeds. Nine male runners wore two ActiGraph uniaxial accelerometers, two RT3 triaxial accelerometers (all set at a 1-s epoch), and two Yamax pedometers. Each participant walked for 60 s at 4 and 6 km x h(-1), ran for 60 s at 10, 12, 14, 16, and 18 km x h(-1), and ran for 30 s at 20, 22, 24, and 26 km x h(-1). Step frequency was recorded by a visual count. ActiGraph counts peaked at 10 km x h(-10 (2.5-3.0 Hz SF) and declined thereafter (r=0.02, P>0.05). After correction for frequency-dependent filtering, output plateaued at 10 km x h(-1) but did not decline (r=0.77, P<0.05). Similarly, RT3 vertical counts plateaued at speeds > 10 km x h(-1) (r=0.86, P<0.01). RT3 vector magnitude and anteroposterior and mediolateral counts maintained a linear relationship with speed (r>0.96, P<0.001). Step frequency assessed by pedometry compared well with actual step frequency up to 20 km x h(-1) (approximately 3.5 Hz) but then underestimated actual steps (Yamax r=0.97; ActiGraph pedometer r=0.88, both P<0.001). Increasing underestimation of activity by the ActiGraph as speed increases is related to frequency-dependent filtering and assessment of acceleration in the vertical plane only. RT3 vector magnitude was strongly related to speed, reflecting the predominance of horizontal acceleration at higher speeds. These results indicate that high-intensity activity is underestimated by the ActiGraph, even after correction for frequency-dependent filtering, but not by the RT3. Pedometer output is highly correlated with step frequency.

Heat and mass transfer and hydrodynamics in swirling flows (review)

NASA Astrophysics Data System (ADS)

Leont'ev, A. I.; Kuzma-Kichta, Yu. A.; Popov, I. A.

2017-02-01

Research results of Russian and foreign scientists of heat and mass transfer in whirling flows, swirling effect, superficial vortex generators, thermodynamics and hydrodynamics at micro- and nanoscales, burning at swirl of the flow, and technologies and apparatuses with the use of whirling currents for industry and power generation were presented and discussed at the "Heat and Mass Transfer in Whirling Currents" 5th International Conference. The choice of rational forms of the equipment flow parts when using whirling and swirling flows to increase efficiency of the heat-power equipment and of flow regimes and burning on the basis of deep study of the flow and heat transfer local parameters was set as the main research prospect. In this regard, there is noticeable progress in research methods of whirling and swirling flows. The number of computational treatments of swirling flows' local parameters has been increased. Development and advancement of the up to date computing models and national productivity software are very important for this process. All experimental works are carried out with up to date research methods of the local thermoshydraulic parameters, which enable one to reveal physical mechanisms of processes: PIV and LIV visualization techniques, high-speed and infrared photography, high speed registration of parameters of high-speed processes, etc. There is a problem of improvement of researchers' professional skills in the field of fluid mechanics to set adequately mathematics and physics problems of aerohydrodynamics for whirling and swirling flows and numerical and pilot investigations. It has been pointed out that issues of improvement of the cooling system and thermal protection effectiveness of heat-power and heat-transfer equipment units are still actual. It can be solved successfully using whirling and swirling flows as simple low power consumption exposing on the flow method and heat transfer augmentation.

Normative data for the Stroop color word test for a North American population.

PubMed

Morrow, Sarah A

2013-11-01

Cognitive impairment in multiple sclerosis (MS) often involves attentional deficits. The Stroop colour word test, a measure of attention, lacks current normative data for an english-speaking North american MS population. Further some authors suggest the Stroop actually measures processing speed. To generate normative data for the Stroop colour word test that can be used for a Canadian or North american MS population and to examine the relationship between processing speed tests--the Paced auditory Serial addition Test (PASAT) and Symbol Digit Modalities Test (SDMT)--and the Stroop. Data from 146 healthy subjects aged 18-56 was collected. age was significantly although weakly correlated with general intelligence (r=0.168, p=0.043) assessed with the North american adult Reading Test (NAART), and education (r=-0.313, p<0.001). No demographic variables were associated with SDMT or PASAT. age had a low-moderate negative correlation (r=-0.403, p<0.001) with Stroop scores. The mean (±standard deviation, SD) Stroop score was 45.4(10.4). The z-score can thus be calculated as [(X-45.4)/10.4]. if adjusted for age, Xadj = [X-(-0.47)(age-37.5)] and is substituted for X. in a comparison MS population consisting of 75 randomly selected patients from the MS Cognitive clinic, Stroop and PASAT performance were not related. a relationship existed between Stroop and SDMT scores but only 12.2% of the Stroop score variance was explained by the SDMT. Therefore, the Stroop measures selective attention independently of processing speed. This data can be used to determine impaired attention in MS patients. Données normatives pour le test mot-couleur de Stroop chez une population nord-américaine.

Speed ratio but cabin temperature positively correlated with increased heart rates among professional drivers during car races.

PubMed

Yanagida, Ryo; Takahashi, Kiichi; Miura, Masaru; Nomura, Masahiro; Ogawa, Yojiro; Aoki, Ken; Iwasaki, Ken-Ichi

2016-11-01

The present study measures heart rate (HR) on a number of professional race-car drivers during actual car races through annual seasons to test hypotheses that faster relative speed and higher cabin temperature would induce higher HR. Heart rates in fifteen male drivers (31.2 ± 5.5 years old) were obtained by chest-strap sensors during official-professional 13 races. Average HR was calculated while the driver was racing from the start to the end of each race. The average HR during races was 164.5 ± 15.1 beats min -1 and the average amount of time each driver spent driving per race was 54.2 ± 13.7 min. Average HR significantly and positively correlated with mean speed ratio (P < 0.001), but not with the average cabin temperatures (P = 0.533, range 25.6-41.8 °C) by the multiple linear regression analysis. Both average HR and mean speed ratio were significantly lower under wet, than dry conditions (151.9 ± 16.5 vs. 168.3 ± 12.5 beats min -1 , 86.9 ± 4.4 vs. 93.4 ± 1.5 %). The cardiovascular system of drivers is considerably stressed at extremely high HR. This high average HR positively correlated with mean speed ratio, suggesting that faster driving speed would induce greater cardiovascular stress to professional drivers during actual races. However, contrary to our hypothesis, cabin temperature was not significantly correlated with average HR. It is speculated that direct body cooling systems used in this professional race category work well against increases in HR by thermal stress under the temperature range found herein.

Engine speed control apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishii, M.; Miyazaki, M.; Nakamura, N.

1986-11-04

This patent describes an engine speed control apparatus. The system comprises an actuator for adjusting an engine speed, a first unit for computing a desired engine speed, a second unit for detecting the actual engine speed, and a third unit for detecting the difference between the outputs of the first and second units. The system also includes a fourth unit for computing a control pulse width for the actuator in accordance with the output of the third unit, a fifth unit for generating a control signal, a sixth unit for driving the actuator in response to the output of themore » fifth unit, and a seventh unit for computing an optimal halt time to interrupt the driving of the actuator. The actuator is driven intermittently in conformity in the control pulse width and the halt time.« less

Dark soliton past a finite-size obstacle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilas, Nicolas; Pavloff, Nicolas

2005-09-15

We consider the collision of a dark soliton with an obstacle in a quasi-one-dimensional Bose condensate. We show that in many respects the soliton behaves as an effective classical particle of mass twice the mass of a bare particle, evolving in an effective potential which is a convolution of the actual potential describing the obstacle. Radiative effects beyond this approximation are also taken into account. The emitted waves are shown to form two counterpropagating wave packets, both moving at the speed of sound. We determine, at leading order, the total amount of radiation emitted during the collision and compute themore » acceleration of the soliton due to the collisional process. It is found that the radiative process is quenched when the velocity of the soliton reaches the velocity of sound in the system.« less

Design and Verification of Remote Sensing Image Data Center Storage Architecture Based on Hadoop

NASA Astrophysics Data System (ADS)

Tang, D.; Zhou, X.; Jing, Y.; Cong, W.; Li, C.

2018-04-01

The data center is a new concept of data processing and application proposed in recent years. It is a new method of processing technologies based on data, parallel computing, and compatibility with different hardware clusters. While optimizing the data storage management structure, it fully utilizes cluster resource computing nodes and improves the efficiency of data parallel application. This paper used mature Hadoop technology to build a large-scale distributed image management architecture for remote sensing imagery. Using MapReduce parallel processing technology, it called many computing nodes to process image storage blocks and pyramids in the background to improve the efficiency of image reading and application and sovled the need for concurrent multi-user high-speed access to remotely sensed data. It verified the rationality, reliability and superiority of the system design by testing the storage efficiency of different image data and multi-users and analyzing the distributed storage architecture to improve the application efficiency of remote sensing images through building an actual Hadoop service system.

Development of an Automatic Detection Program of Halo CMEs

NASA Astrophysics Data System (ADS)

Choi, K.; Park, M. Y.; Kim, J.

2017-12-01

The front-side halo CMEs are the major cause for large geomagnetic storms. Halo CMEs can result in damage to satellites, communication, electrical transmission lines and power systems. Thus automated techniques for detecting and analysing Halo CMEs from coronagraph data are of ever increasing importance for space weather monitoring and forecasting. In this study, we developed the algorithm that can automatically detect and do image processing the Halo CMEs in the images from the LASCO C3 coronagraph on board the SOHO spacecraft. With the detection algorithm, we derived the geometric and kinematical parameters of halo CMEs, such as source location, width, actual CME speed and arrival time at 21.5 solar radii.

Approach for axisymmetrical asphere polishing with full-area tools

NASA Astrophysics Data System (ADS)

Novi, Andrea; Melozzi, Mauro

1999-09-01

Aspherics up to 500 nm diameter in optical glass or in ceramic substrates have been fabricated using area- compensated polishing tools and conventional optical shop machines. The tool forms are derived starting from the actual shape of the part under figuring. The figure error is measured using an interferometer mounted on-line with the polishing machine. Measurements are taken after each polishing step to compute the new tool form. The process speeds up the fabrication of aspheres and it improves repeatability in the manufacturing of axisymmetrical optics using moderate cost equipment's up to astronomical requirements. In the paper we present some examples of polishing results using the above mentioned approach on different aspherics for space applications.

Traction Aid for Wheeled Vehicles

DTIC Science & Technology

1975-07-01

driver’s position in the load vehicle to assist him in applying constant braking loads, 4) a drum and line fifth wheel sys- tem attached to the load...in Alaskan snow, and the results were so encouraging that further testing of the device was requested. In comparison to tire chains, the Tyr-Trac...vehicle with the end of the line anchored and the speed of the line played off the drum measuring the actual vehicle speed. An eight channel

Exploring stop-go decision zones at rural high-speed intersections with flashing green signal and insufficient yellow time in China.

PubMed

Tang, Keshuang; Xu, Yanqing; Wang, Fen; Oguchi, Takashi

2016-10-01

The objective of this study is to empirically analyze and model the stop-go decision behavior of drivers at rural high-speed intersections in China, where a flashing green signal of 3s followed by a yellow signal of 3s is commonly applied to end a green phase. 1, 186 high-resolution vehicle trajectories were collected at four typical high-speed intersection approaches in Shanghai and used for the identification of actual stop-go decision zones and the modeling of stop-go decision behavior. Results indicate that the presence of flashing green significantly changed the theoretical decision zones based on the conventional Dilemma Zone theory. The actual stop-go decision zones at the study intersections were thus formulated and identified based on the empirical data. Binary Logistic model and Fuzzy Logic model were then developed to further explore the impacts of flashing green on the stop-go behavior of drivers. It was found that the Fuzzy Logic model could produce comparably good estimation results as compared to the traditional Binary Logistic models. The findings of this study could contribute the development of effective dilemma zone protection strategies, the improvement of stop-go decision model embedded in the microscopic traffic simulation software and the proper design of signal change and clearance intervals at high-speed intersections in China. Copyright © 2016 Elsevier Ltd. All rights reserved.

A Vision-Aided 3D Path Teaching Method before Narrow Butt Joint Welding

PubMed Central

Zeng, Jinle; Chang, Baohua; Du, Dong; Peng, Guodong; Chang, Shuhe; Hong, Yuxiang; Wang, Li; Shan, Jiguo

2017-01-01

For better welding quality, accurate path teaching for actuators must be achieved before welding. Due to machining errors, assembly errors, deformations, etc., the actual groove position may be different from the predetermined path. Therefore, it is significant to recognize the actual groove position using machine vision methods and perform an accurate path teaching process. However, during the teaching process of a narrow butt joint, the existing machine vision methods may fail because of poor adaptability, low resolution, and lack of 3D information. This paper proposes a 3D path teaching method for narrow butt joint welding. This method obtains two kinds of visual information nearly at the same time, namely 2D pixel coordinates of the groove in uniform lighting condition and 3D point cloud data of the workpiece surface in cross-line laser lighting condition. The 3D position and pose between the welding torch and groove can be calculated after information fusion. The image resolution can reach 12.5 μm. Experiments are carried out at an actuator speed of 2300 mm/min and groove width of less than 0.1 mm. The results show that this method is suitable for groove recognition before narrow butt joint welding and can be applied in path teaching fields of 3D complex components. PMID:28492481

A Vision-Aided 3D Path Teaching Method before Narrow Butt Joint Welding.

PubMed

Zeng, Jinle; Chang, Baohua; Du, Dong; Peng, Guodong; Chang, Shuhe; Hong, Yuxiang; Wang, Li; Shan, Jiguo

2017-05-11

For better welding quality, accurate path teaching for actuators must be achieved before welding. Due to machining errors, assembly errors, deformations, etc., the actual groove position may be different from the predetermined path. Therefore, it is significant to recognize the actual groove position using machine vision methods and perform an accurate path teaching process. However, during the teaching process of a narrow butt joint, the existing machine vision methods may fail because of poor adaptability, low resolution, and lack of 3D information. This paper proposes a 3D path teaching method for narrow butt joint welding. This method obtains two kinds of visual information nearly at the same time, namely 2D pixel coordinates of the groove in uniform lighting condition and 3D point cloud data of the workpiece surface in cross-line laser lighting condition. The 3D position and pose between the welding torch and groove can be calculated after information fusion. The image resolution can reach 12.5 μm. Experiments are carried out at an actuator speed of 2300 mm/min and groove width of less than 0.1 mm. The results show that this method is suitable for groove recognition before narrow butt joint welding and can be applied in path teaching fields of 3D complex components.

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling

PubMed Central

Zhang, Tao; Li, Lei; Lu, Shi-Hong; Gong, Hai; Wu, Yun-Xin

2018-01-01

Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX) plays a vital role in grain refinement during hot deformation. Finite element models (FEM) coupled with microstructure evolution models and cellular automata models (CA) are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation. PMID:29342080

Comparisons of Different Models on Dynamic Recrystallization of Plate during Asymmetrical Shear Rolling.

PubMed

Zhang, Tao; Li, Lei; Lu, Shi-Hong; Gong, Hai; Wu, Yun-Xin

2018-01-17

Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX) plays a vital role in grain refinement during hot deformation. Finite element models (FEM) coupled with microstructure evolution models and cellular automata models (CA) are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation.

Traction contact performance evaluation at high speeds

NASA Technical Reports Server (NTRS)

Tevaarwerk, J. L.

1981-01-01

The results of traction tests performed on two fluids are presented. These tests covered a pressure range of 1.0 to 2.5 GPa, an inlet temperature range of 30 'C to 70 'C, a speed range of 10 to 80 m/sec, aspect ratios of .5 to 5 and spin from 0 to 2.1 percent. The test results are presented in the form of two dimensionless parameters, the initial traction slope and the maximum traction peak. With the use of a suitable rheological fluid model the actual traction curves measured can now be reconstituted from the two fluid parameters. More importantly, the knowledge of these parameters together with the fluid rheological model, allow the prediction of traction under conditions of spin, slip and any combination thereof. Comparison between theoretically predicted traction under these conditions and those measured in actual traction tests shows that this method gives good results.

Control means for a gas turbine engine

NASA Technical Reports Server (NTRS)

Beitler, R. S.; Sellers, F. J.; Bennett, G. W. (Inventor)

1982-01-01

A means is provided for developing a signal representative of the actual compressor casing temperature, a second signal representative of compressor inlet gas temperature, and a third signal representative of compressor speed. Another means is provided for receiving the gas temperature and compressor speed signals and developing a schedule output signal which is a representative of a reference casing temperature at which a predetermined compressor blade stabilized clearance is provided. A means is also provided for comparing the actual compressor casing temperature signal and the reference casing temperature signal and developing a clearance control system representative of the difference. The clearance control signal is coupled to a control valve which controls a flow of air to the compressor casing to control the clearance between the compressor blades and the compressor casing. The clearance control signal can be modified to accommodate transient characteristics. Other embodiments are disclosed.

Traffic safety effects of new speed limits in Sweden.

PubMed

Vadeby, Anna; Forsman, Åsa

2018-05-01

The effects of speed, both positive and negative, make speed a primary target for policy action. Driving speeds affect the risk of being involved in a crash and the injury severity as well as the noise and exhaust emissions. Starting 2008, the Swedish Transport Administration performed a review of the speed limits on the national rural road network. This review resulted in major changes of the speed limits on the rural road network. It was predominantly roads with a low traffic safety standard and unsatisfactory road sides that were selected for reduced speed limits, as well as roads with a good traffic safety record being selected for an increase in speed limits. During 2008 and 2009, speed limit changed on approximately 20,500km of roads, out of which approximately 2700km were assigned an increase, and 17,800km were assigned a reduction in speed limits. The aim of this study is predominantly to describe and analyse the longterm traffic safety effect of increased, as well as, reduced speed limits, but also to analyse the changes in actual driving speeds due to the changed speed limits. Traffic safety effects are investigated by means of a before and after study with control group and the effects on actual mean speeds are measured by a sampling survey in which speed was measured at randomly selected sites before and after the speed limit changes. Results show a reduction in fatalities on rural roads with reduced speed limit from 90 to 80km/h where the number of fatalities decreased by 14 per year, while no significant changes were seen for the seriously injured. On motorways with an increased speed limit to 120km/h, the number of seriously injured increased by about 15 per year, but no significant changes were seen for the number of deaths. The number of seriously injured increased on all types of motorways, but the worst development was seen for narrow motorways (21.5m wide). For 2+1 roads (a continuous three-lane cross-section with alternating passing lanes and the two directions of travel separated by a median barrier) with decreased speed limit from 110 to 100km/h, the seriously injured decreased by about 16 per year. As regards the change of mean speeds, a decrease in speed limit with 10km/h led to a decrease of mean speeds of around 2-3km/h and an increase of the speed limit with 10km/h resulted in an increase of mean speed by 3km/h. In conclusion, the results show that in total about 17 lives per year have been saved on the road network with changed speed limits. For comparison, 397 road users were killed in total during 2008. The number of seriously injured remain in principle unchanged. It should also be noted that the results are obtained for the road network which changed the speed limits during 2008 and 2009, and it is not certain that the results can be generalised to another road network. Copyright © 2017 Elsevier Ltd. All rights reserved.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Lee H. (Inventor)

1989-01-01

The invention is a real-time takeoff and landing performance monitoring system which provides the pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V sub R) within the safe zone of the runway or stopping the aircraft on the runway after landing or take off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. An important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in headwind occurring as the takeoff roll progresses. The system displays the position of the airplane on the runway, indicating runway used and runway available, summarizes the critical information into a situation advisory flag, flags engine failures and off-nominal acceleration performance, and indicates where on the runway particular events such as decision speed (V sub 1), rotation speed (V sub R) and expected stop points will occur based on actual or predicted performance. The display also indicates airspeed, wind vector, engine pressure ratios, second segment climb speed, and balanced field length (BFL). The system detects performance deficiencies by comparing the airplane's present performance with a predicted nominal performance based upon the given conditions.

Differences in physical environmental characteristics between adolescents' actual and shortest cycling routes: a study using a Google Street View-based audit.

PubMed

Verhoeven, Hannah; Van Hecke, Linde; Van Dyck, Delfien; Baert, Tim; Van de Weghe, Nico; Clarys, Peter; Deforche, Benedicte; Van Cauwenberg, Jelle

2018-05-29

The objective evaluation of the physical environmental characteristics (e.g. speed limit, cycling infrastructure) along adolescents' actual cycling routes remains understudied, although it may provide important insights into why adolescents prefer one cycling route over another. The present study aims to gain insight into the physical environmental characteristics determining the route choice of adolescent cyclists by comparing differences in physical environmental characteristics between their actual cycling routes and the shortest possible cycling routes. Adolescents (n = 204; 46.5% boys; 14.4 ± 1.2 years) recruited at secondary schools in and around Ghent (city in Flanders, northern part of Belgium) were instructed to wear a Global Positioning System device in order to identify cycling trips. For all identified cycling trips, the shortest possible route that could have been taken was calculated. Actual cycling routes that were not the shortest possible cycling routes were divided into street segments. Segments were audited with a Google Street View-based tool to assess physical environmental characteristics along actual and shortest cycling routes. Out of 160 actual cycling trips, 73.1% did not differ from the shortest possible cycling route. For actual cycling routes that were not the shortest cycling route, a speed limit of 30 km/h, roads having few buildings with windows on the street side and roads without cycle lane were more frequently present compared to the shortest possible cycling routes. A mixed land use, roads with commercial destinations, arterial roads, cycle lanes separated from traffic by white lines, small cycle lanes and cycle lanes covered by lighting were less frequently present along actual cycling routes compared to the shortest possible cycling routes. Results showed that distance mainly determines the route along which adolescents cycle. In addition, adolescents cycled more along residential streets (even if no cycle lane was present) and less along busy, arterial roads. Local authorities should provide shortcuts free from motorised traffic to meet adolescents' preference to cycle along the shortest route and to avoid cycling along arterial roads.

Thermal and Melt Wear Characterization of Materials in Sliding Contact at High Speed

DTIC Science & Technology

2014-03-01

wraparound slipper restrains the sled from flying off the rails as a result of aerodynamic lifting on the body . Figure 4 shows a representative VascoMax...in January 2008 to predict dynamic behavior of the rocket sled system during the actual test run. The left rear slipper from the third stage car...computational fluid dynamics model. Further, the slipper under consideration is the actual slipper of the third stage of the rocket sled, so the supersonic

Photoelectric radar servo control system based on ARM+FPGA

NASA Astrophysics Data System (ADS)

Wu, Kaixuan; Zhang, Yue; Li, Yeqiu; Dai, Qin; Yao, Jun

2016-01-01

In order to get smaller, faster, and more responsive requirements of the photoelectric radar servo control system. We propose a set of core ARM + FPGA architecture servo controller. Parallel processing capability of FPGA to be used for the encoder feedback data, PWM carrier modulation, A, B code decoding processing and so on; Utilizing the advantage of imaging design in ARM Embedded systems achieves high-speed implementation of the PID algorithm. After the actual experiment, the closed-loop speed of response of the system cycles up to 2000 times/s, in the case of excellent precision turntable shaft, using a PID algorithm to achieve the servo position control with the accuracy of + -1 encoder input code. Firstly, This article carry on in-depth study of the embedded servo control system hardware to determine the ARM and FPGA chip as the main chip with systems based on a pre-measured target required to achieve performance requirements, this article based on ARM chip used Samsung S3C2440 chip of ARM7 architecture , the FPGA chip is chosen xilinx's XC3S400 . ARM and FPGA communicate by using SPI bus, the advantage of using SPI bus is saving a lot of pins for easy system upgrades required thereafter. The system gets the speed datas through the photoelectric-encoder that transports the datas to the FPGA, Then the system transmits the datas through the FPGA to ARM, transforms speed datas into the corresponding position and velocity data in a timely manner, prepares the corresponding PWM wave to control motor rotation by making comparison between the position data and the velocity data setted in advance . According to the system requirements to draw the schematics of the photoelectric radar servo control system and PCB board to produce specially. Secondly, using PID algorithm to control the servo system, the datas of speed obtained from photoelectric-encoder is calculated position data and speed data via high-speed digital PID algorithm and coordinate models. Finally, a large number of experiments verify the reliability of embedded servo control system's functions, the stability of the program and the stability of the hardware circuit. Meanwhile, the system can also achieve the satisfactory of user experience, to achieve a multi-mode motion, real-time motion status monitoring, online system parameter changes and other convenient features.

Locust displacing winds in eastern Australia reassessed with observations from an insect monitoring radar

NASA Astrophysics Data System (ADS)

Hao, Zhenhua; Drake, V. Alistair; Sidhu, Leesa; Taylor, John R.

2017-12-01

Based on previous investigations, adult Australian plague locusts are believed to migrate on warm nights (with evening temperatures >25 °C), provided daytime flight is suppressed by surface winds greater than the locusts' flight speed, which has been shown to be 3.1 m s-1. Moreover, adult locusts are believed to undertake briefer `dispersal' flights on nights with evening temperature >20 °C. To reassess the utility of these conditions for forecasting locust flight, contingency tests were conducted comparing the nights selected on these bases (predicted nights) for the months of November, January, and March and the nights when locust migration were detected with an insect monitoring radar (actual nights) over a 7-year period. In addition, the wind direction distributions and mean wind directions on all predicted nights and actual nights were compared. Observations at around 395 m above ground level (AGL), the height at which radar observations have shown that the greatest number of locusts fly, were used to determine the actual nights. Tests and comparisons were also made for a second height, 990 m AGL, as this was used in the previous investigation. Our analysis shows that the proposed criteria are successful from predicting migratory flight only in March, when the surface temperature is effective as a predicting factor. Surface wind speed has no predicting power. It is suggested that a strong daytime surface wind speed requirement should not be considered and other meteorological variables need to be added to the requirement of a warm surface temperature around dusk for the predictions to have much utility.

A reward semi-Markov process with memory for wind speed modeling

NASA Astrophysics Data System (ADS)

Petroni, F.; D'Amico, G.; Prattico, F.

2012-04-01

The increasing interest in renewable energy leads scientific research to find a better way to recover most of the available energy. Particularly, the maximum energy recoverable from wind is equal to 59.3% of that available (Betz law) at a specific pitch angle and when the ratio between the wind speed in output and in input is equal to 1/3. The pitch angle is the angle formed between the airfoil of the blade of the wind turbine and the wind direction. Old turbine and a lot of that actually marketed, in fact, have always the same invariant geometry of the airfoil. This causes that wind turbines will work with an efficiency that is lower than 59.3%. New generation wind turbines, instead, have a system to variate the pitch angle by rotating the blades. This system able the wind turbines to recover, at different wind speed, always the maximum energy, working in Betz limit at different speed ratios. A powerful system control of the pitch angle allows the wind turbine to recover better the energy in transient regime. A good stochastic model for wind speed is then needed to help both the optimization of turbine design and to assist the system control to predict the value of the wind speed to positioning the blades quickly and correctly. The possibility to have synthetic data of wind speed is a powerful instrument to assist designer to verify the structures of the wind turbines or to estimate the energy recoverable from a specific site. To generate synthetic data, Markov chains of first or higher order are often used [1,2,3]. In particular in [1] is presented a comparison between a first-order Markov chain and a second-order Markov chain. A similar work, but only for the first-order Markov chain, is conduced by [2], presenting the probability transition matrix and comparing the energy spectral density and autocorrelation of real and synthetic wind speed data. A tentative to modeling and to join speed and direction of wind is presented in [3], by using two models, first-order Markov chain with different number of states, and Weibull distribution. All this model use Markov chains to generate synthetic wind speed time series but the search for a better model is still open. Approaching this issue, we applied new models which are generalization of Markov models. More precisely we applied semi-Markov models to generate synthetic wind speed time series. The primary goal of this analysis is the study of the time history of the wind in order to assess its reliability as a source of power and to determine the associated storage levels required. In order to assess this issue we use a probabilistic model based on indexed semi-Markov process [4] to which a reward structure is attached. Our model is used to calculate the expected energy produced by a given turbine and its variability expressed by the variance of the process. Our results can be used to compare different wind farms based on their reward and also on the risk of missed production due to the intrinsic variability of the wind speed process. The model is used to generate synthetic time series for wind speed by means of Monte Carlo simulations and backtesting procedure is used to compare results on first and second oder moments of rewards between real and synthetic data. [1] A. Shamshad, M.A. Bawadi, W.M.W. Wan Hussin, T.A. Majid, S.A.M. Sanusi, First and second order Markov chain models for synthetic gen- eration of wind speed time series, Energy 30 (2005) 693-708. [2] H. Nfaoui, H. Essiarab, A.A.M. Sayigh, A stochastic Markov chain model for simulating wind speed time series at Tangiers, Morocco, Re- newable Energy 29 (2004) 1407-1418. [3] F. Youcef Ettoumi, H. Sauvageot, A.-E.-H. Adane, Statistical bivariate modeling of wind using first-order Markov chain and Weibull distribu- tion, Renewable Energy 28 (2003) 1787-1802. [4]F. Petroni, G. D'Amico, F. Prattico, Indexed semi-Markov process for wind speed modeling. To be submitted.

Effects of yolk contamination, shearing, and heating on foaming properties of fresh egg white.

PubMed

Wang, G; Wang, T

2009-03-01

A series of experiments were conducted to evaluate effects of yolk contamination, shearing, and thermal treatment on foaming properties of liquid egg white. Samples obtained from industrial processing were also evaluated. Whipping and purging methods were both used to assess their effectiveness and sensitivity in evaluating foaming. A concentration as low as 0.022% (as-is basis) of yolk contamination caused significant reductions in foaming capacity and foaming speed. The neutral lipid fraction of egg yolk caused the major detrimental effect on foaming, and phospholipids fraction did not give significant foaming reduction at a concentration as high as 0.1%. High-speed and short-time shearing caused no apparent damage but longer shearing time significantly impaired foaming. Heat-induced foaming change is a function of temperature and holding time. Foaming was significantly reduced at a temperature of 55 degrees C for 10 min, whereas it did not change up to 3 min at a heating temperature of 62 to 64 degrees C. Industrial processing steps (pumping, pipe transfer, and storage) did not produce negative effects on foaming of the final products and the controlled pasteurization was actually beneficial for good foaming performance. Therefore, yolk contamination of the egg white was the major factor in reducing foaming properties of the white protein.

3D frequency-domain ultrasound waveform tomography breast imaging

NASA Astrophysics Data System (ADS)

Sandhu, Gursharan Yash; West, Erik; Li, Cuiping; Roy, Olivier; Duric, Neb

2017-03-01

Frequency-domain ultrasound waveform tomography is a promising method for the visualization and characterization of breast disease. It has previously been shown to accurately reconstruct the sound speed distributions of breasts of varying densities. The reconstructed images show detailed morphological and quantitative information that can help differentiate different types of breast disease including benign and malignant lesions. The attenuation properties of an ex vivo phantom have also been assessed. However, the reconstruction algorithms assumed a 2D geometry while the actual data acquisition process was not. Although clinically useful sound speed images can be reconstructed assuming this mismatched geometry, artifacts from the reconstruction process exist within the reconstructed images. This is especially true for registration across different modalities and when the 2D assumption is violated. For example, this happens when a patient's breast is rapidly sloping. It is also true for attenuation imaging where energy lost or gained out of the plane gets transformed into artifacts within the image space. In this paper, we will briefly review ultrasound waveform tomography techniques, give motivation for pursuing the 3D method, discuss the 3D reconstruction algorithm, present the results of 3D forward modeling, show the mismatch that is induced by the violation of 3D modeling via numerical simulations, and present a 3D inversion of a numerical phantom.

Magnetic suspension system for an Annular Momentum Control Device (AMCD)

NASA Technical Reports Server (NTRS)

1979-01-01

A technique to control a rim suspended in a magnetic field was developed. A complete system was developed, incorporating a support structure, magnetic actuators, a rim drive mechanism, an emergency fail-safe system, servo control system, and control electronics. Open loop and closed loop response of the system at zero speed and at 500 revolutions per minute (r/min) of the rim was obtained and analyzed. The rim was then dynamically balanced and a rim speed of 725 r/min was achieved. An analog simulation of the hardware was developed and tested with the actual control electronics connected to the analog computer. The system under development is stable at rim speeds below 700 r/min. Test results indicate that the rim under test is not rigid. The rim has a warp and a number of binding modes which prevented achievement of higher speeds. Further development efforts are required to achieve higher rim speeds.

Effects of sea maturity on satellite altimeter measurements

NASA Technical Reports Server (NTRS)

Glazman, Roman E.; Pilorz, Stuart H.

1990-01-01

For equilibrium and near-equilibrium sea states, the wave slope variance is a function of wind speed U and of the sea maturity. The influence of both factors on the altimeter measurements of wind speed, wave height, and radar cross section is studied experimentally on the basis of 1 year's worth of Geosat altimeter observations colocated with in situ wind and wave measurements by 20 NOAA buoys. Errors and biases in altimeter wind speed and wave height measurements are investigted. A geophysically significant error trend correlated with the sea maturity is found in wind-speed measurements. This trend is explained by examining the effect of the generalized wind fetch on the curves of the observed dependence. It is concluded that unambiguous measurements of wind speed by altimeter, in a wide range of sea states, are impossible without accounting for the actual degree of wave development.

[Attention to speed and guide traffic signs with eye movements].

PubMed

Conchillo Jiménez, Ángela; Pérez-Moreno, Elisa; Recarte Goldaracena, Miguel Ángel

2010-11-01

The goal of this research is to describe the visual search patterns for diverse traffic signs. Twelve drivers of both genders and different driving experience levels took part in real driving research with an instrumented car provided with an eye-tracking system. Looking at signs has a weak relation with speed reduction in cases where actual driving speed was higher. Nevertheless, among the people who looked at the sign, the percentage of those who reduce the speed below the limit is greater than of those who do not look at the sign. Guide traffic signs, particularly those mounted over the road, are more frequently glanced at than speed limit signs, with a glance duration of more than one second, in sequences of more than two consecutive fixations. Implications for driving and the possibilities and limitations of eye movement analysis for traffic sign research are discussed.

Calculation of equivalent friction coefficient for castor seed by single screw press

NASA Astrophysics Data System (ADS)

Liu, R.; Xiao, Z.; Li, C.; Zhang, L.; Li, P.; Li, H.; Zhang, A.; Tang, S.; Sun, F.

2017-08-01

Based on the traction angle and transportation rate equation, castor beans were pressed by application of single screw under different cake diameter and different screw speed. The results showed that the greater the cake diameter and screw rotation speed, the greater the actual transmission rate was. The equivalent friction coefficient was defined and calculated as 0.4136, and the friction coefficients between press material and screw, bar cage were less than the equivalent friction coefficient value.

Computational fluid mechanics utilizing the variational principle of modeling damping seals

NASA Technical Reports Server (NTRS)

Abernathy, J. M.

1986-01-01

A computational fluid dynamics code for application to traditional incompressible flow problems has been developed. The method is actually a slight compressibility approach which takes advantage of the bulk modulus and finite sound speed of all real fluids. The finite element numerical analog uses a dynamic differencing scheme based, in part, on a variational principle for computational fluid dynamics. The code was developed in order to study the feasibility of damping seals for high speed turbomachinery. Preliminary seal analyses have been performed.

Modeling and predicting low-speed vehicle emissions as a function of driving kinematics.

PubMed

Hao, Lijun; Chen, Wei; Li, Lei; Tan, Jianwei; Wang, Xin; Yin, Hang; Ding, Yan; Ge, Yunshan

2017-05-01

An instantaneous emission model was developed to model and predict the real driving emissions of the low-speed vehicles. The emission database used in the model was measured by using portable emission measurement system (PEMS) under actual traffic conditions in the rural area, and the characteristics of the emission data were determined in relation to the driving kinematics (speed and acceleration) of the low-speed vehicle. The input of the emission model is driving cycle, and the model requires instantaneous vehicle speed and acceleration levels as input variables and uses them to interpolate the pollutant emission rate maps to calculate the transient pollutant emission rates, which will be accumulated to calculate the total emissions released during the whole driving cycle. And the vehicle fuel consumption was determined through the carbon balance method. The model predicted the emissions and fuel consumption of an in-use low-speed vehicle type model, which agreed well with the measured data. Copyright © 2016. Published by Elsevier B.V.

Foggy perception slows us down

PubMed Central

Pretto, Paolo; Bresciani, Jean-Pierre; Rainer, Gregor; Bülthoff, Heinrich H

2012-01-01

Visual speed is believed to be underestimated at low contrast, which has been proposed as an explanation of excessive driving speed in fog. Combining psychophysics measurements and driving simulation, we confirm that speed is underestimated when contrast is reduced uniformly for all objects of the visual scene independently of their distance from the viewer. However, we show that when contrast is reduced more for distant objects, as is the case in real fog, visual speed is actually overestimated, prompting drivers to decelerate. Using an artificial anti-fog—that is, fog characterized by better visibility for distant than for close objects, we demonstrate for the first time that perceived speed depends on the spatial distribution of contrast over the visual scene rather than the global level of contrast per se. Our results cast new light on how reduced visibility conditions affect perceived speed, providing important insight into the human visual system. DOI: http://dx.doi.org/10.7554/eLife.00031.001 PMID:23110253

Effects of children's working memory capacity and processing speed on their sentence imitation performance.

PubMed

Poll, Gerard H; Miller, Carol A; Mainela-Arnold, Elina; Adams, Katharine Donnelly; Misra, Maya; Park, Ji Sook

2013-01-01

More limited working memory capacity and slower processing for language and cognitive tasks are characteristics of many children with language difficulties. Individual differences in processing speed have not consistently been found to predict language ability or severity of language impairment. There are conflicting views on whether working memory and processing speed are integrated or separable abilities. To evaluate four models for the relations of individual differences in children's processing speed and working memory capacity in sentence imitation. The models considered whether working memory and processing speed are integrated or separable, as well as the effect of the number of operations required per sentence. The role of working memory as a mediator of the effect of processing speed on sentence imitation was also evaluated. Forty-six children with varied language and reading abilities imitated sentences. Working memory was measured with the Competing Language Processing Task (CLPT), and processing speed was measured with a composite of truth-value judgment and rapid automatized naming tasks. Mixed-effects ordinal regression models evaluated the CLPT and processing speed as predictors of sentence imitation item scores. A single mediator model evaluated working memory as a mediator of the effect of processing speed on sentence imitation total scores. Working memory was a reliable predictor of sentence imitation accuracy, but processing speed predicted sentence imitation only as a component of a processing speed by number of operations interaction. Processing speed predicted working memory capacity, and there was evidence that working memory acted as a mediator of the effect of processing speed on sentence imitation accuracy. The findings support a refined view of working memory and processing speed as separable factors in children's sentence imitation performance. Processing speed does not independently explain sentence imitation accuracy for all sentence types, but contributes when the task requires more mental operations. Processing speed also has an indirect effect on sentence imitation by contributing to working memory capacity. © 2013 Royal College of Speech and Language Therapists.

The Role of Visual Processing Speed in Reading Speed Development

PubMed Central

Lobier, Muriel; Dubois, Matthieu; Valdois, Sylviane

2013-01-01

A steady increase in reading speed is the hallmark of normal reading acquisition. However, little is known of the influence of visual attention capacity on children's reading speed. The number of distinct visual elements that can be simultaneously processed at a glance (dubbed the visual attention span), predicts single-word reading speed in both normal reading and dyslexic children. However, the exact processes that account for the relationship between the visual attention span and reading speed remain to be specified. We used the Theory of Visual Attention to estimate visual processing speed and visual short-term memory capacity from a multiple letter report task in eight and nine year old children. The visual attention span and text reading speed were also assessed. Results showed that visual processing speed and visual short term memory capacity predicted the visual attention span. Furthermore, visual processing speed predicted reading speed, but visual short term memory capacity did not. Finally, the visual attention span mediated the effect of visual processing speed on reading speed. These results suggest that visual attention capacity could constrain reading speed in elementary school children. PMID:23593117

The role of visual processing speed in reading speed development.

PubMed

Lobier, Muriel; Dubois, Matthieu; Valdois, Sylviane

2013-01-01

A steady increase in reading speed is the hallmark of normal reading acquisition. However, little is known of the influence of visual attention capacity on children's reading speed. The number of distinct visual elements that can be simultaneously processed at a glance (dubbed the visual attention span), predicts single-word reading speed in both normal reading and dyslexic children. However, the exact processes that account for the relationship between the visual attention span and reading speed remain to be specified. We used the Theory of Visual Attention to estimate visual processing speed and visual short-term memory capacity from a multiple letter report task in eight and nine year old children. The visual attention span and text reading speed were also assessed. Results showed that visual processing speed and visual short term memory capacity predicted the visual attention span. Furthermore, visual processing speed predicted reading speed, but visual short term memory capacity did not. Finally, the visual attention span mediated the effect of visual processing speed on reading speed. These results suggest that visual attention capacity could constrain reading speed in elementary school children.

Speed isn’t everything: Complex processing speed measures mask individual differences and developmental changes in executive control

PubMed Central

Cepeda, Nicholas J.; Blackwell, Katharine A.; Munakata, Yuko

2012-01-01

The rate at which people process information appears to influence many aspects of cognition across the lifespan. However, many commonly accepted measures of “processing speed” may require goal maintenance, manipulation of information in working memory, and decision-making, blurring the distinction between processing speed and executive control and resulting in overestimation of processing-speed contributions to cognition. This concern may apply particularly to studies of developmental change, as even seemingly simple processing speed measures may require executive processes to keep children and older adults on task. We report two new studies and a re-analysis of a published study, testing predictions about how different processing speed measures influence conclusions about executive control across the life span. We find that the choice of processing speed measure affects the relationship observed between processing speed and executive control, in a manner that changes with age, and that choice of processing speed measure affects conclusions about development and the relationship among executive control measures. Implications for understanding processing speed, executive control, and their development are discussed. PMID:23432836

The human chromokinesin Kid is a plus end-directed microtubule-based motor

PubMed Central

Yajima, Junichiro; Edamatsu, Masaki; Watai-Nishii, Junko; Tokai-Nishizumi, Noriko; Yamamoto, Tadashi; Toyoshima, Yoko Y.

2003-01-01

Kid is a kinesin-like DNA-binding protein known to be involved in chromosome movement during mitosis, although its actual motor function has not been demonstrated. Here, we describe the initial characterization of Kid as a microtubule-based motor using optical trapping microscopy. A bacterially expressed fusion protein consisting of a truncated Kid fragment (amino acids 1–388 or 1–439) is indeed an active microtubule motor with an average speed of ∼160 nm/s, and the polarity of movement is plus end directed. We could not detect processive movement of either monomeric Kid or dimerizing chimeric Kid; however, low levels of processivity (a few steps) cannot be detected with our method. These results are consistent with Kid having a role in chromosome congression in vivo, where it would be responsible for the polar ejection forces acting on the chromosome arms. PMID:12606572

Modeling of Filament Deposition Rapid Prototyping Process with a Closed form Solution

NASA Astrophysics Data System (ADS)

Devlin, Steven Leon

Fused Deposition Modeling (FDM(TM)) or fused filament fabrication (FFF) systems are extrusion-based technologies used to produce functional or near functional parts from a wide variety of plastic materials. First patented by S. Scott Crump and commercialized by Stratasys, Ltd in the early 1990s, this technology, like many additive manufacturing systems, offers significant opportunities for the design and production of complex part structures that are difficult if not impossible to produce using traditional manufacturing methods. Standing on the shoulders of a twenty-five year old invention, a rapidly growing open-source development community has exponentially driven interest in FFF technology. However, part quality often limits use in final product commercial markets. Development of accurate and repeatable methods for determining material strength in FFF produced parts is essential for wide adoption into mainstream manufacturing. This study builds on the empirical, squeeze flow and intermolecular diffusion model research conducted by David Grewell and Avraham Benatar, applying a combined model to predict auto adhesion or healing to FFF part samples. In this research, an experimental study and numerical modeling were performed in order to drive and validate a closed form heat transfer solution for extrusion processes to develop temperature field models. An extrusion-based 3D printing system, with the capacity to vary deposition speeds and temperatures, was used to fabricate the samples. Standardized specimens of Polylactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) filament were used to fabricate the samples with different speeds and temperatures. Micro-scanning of cut and lapped specimens, using an optical microscope, was performed to find the effect of the speed and the temperature on the geometry of the cross-sections. It was found that by increasing the speed of the extrusion printing, the area of the cross-section and the maximum thickness decrease, while the weld/bead geometry minimum thickness increases at higher speeds, although actual part strength appeared to plateau for speeds above 15mm/sec. Temperature effect was found to increase the geometry minimum thickness. In most cases, test results show that by increasing the speed and the temperature, the geometry strength increases. Non-Linear finite element based numerical modeling was performed to predict the strength of the samples. The geometry produced from the optical microscope scanning and typical PLA material properties were used to create the model. The finite element model was able to predict the strength of the tested samples at different speeds and temperatures. Analysis of resulting data and examination of tested samples offer favorable insights and opportunities for additional and continuing investigation.

Is semantic priming (ir)rational? Insights from the speeded word fragment completion task.

PubMed

Heyman, Tom; Hutchison, Keith A; Storms, Gert

2016-10-01

Semantic priming, the phenomenon that a target is recognized faster if it is preceded by a semantically related prime, is a well-established effect. However, the mechanisms producing semantic priming are subject of debate. Several theories assume that the underlying processes are controllable and tuned to prime utility. In contrast, purely automatic processes, like automatic spreading activation, should be independent of the prime's usefulness. The present study sought to disentangle both accounts by creating a situation where prime processing is actually detrimental. Specifically, participants were asked to quickly complete word fragments with either the letter a or e (e.g., sh_ve to be completed as shave). Critical fragments were preceded by a prime that was either related (e.g., push) or unrelated (write) to a prohibited completion of the target (e.g., shove). In 2 experiments, we found a significant inhibitory priming effect, which is inconsistent with purely "rational" explanations of semantic priming. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Improvements in Speed and Functionality of a 670-GHz Imaging Radar

NASA Technical Reports Server (NTRS)

Dengler, Robert J.; Cooper, Ken B.; Mehdi, Imran; Siegel, Peter H.; Tarsala, Jan A.; Bryllert, Thomas E.

2011-01-01

Significant improvements have been made in the instrument originally described in a prior NASA Tech Briefs article: Improved Speed and Functionality of a 580-GHz Imaging Radar (NPO-45156), Vol. 34, No. 7 (July 2010), p. 51. First, the wideband YIG oscillator has been replaced with a JPL-designed and built phase-locked, low-noise chirp source. Second, further refinements to the data acquisition and signal processing software have been performed by moving critical code sections to C code, and compiling those sections to Windows DLLs, which are then invoked from the main LabVIEW executive. This system is an active, single-pixel scanned imager operating at 670 GHz. The actual chirp signals for the RF and LO chains were generated by a pair of MITEQ 2.5 3.3 GHz chirp sources. Agilent benchtop synthesizers operating at fixed frequencies around 13 GHz were then used to up-convert the chirp sources to 15.5 16.3 GHz. The resulting signals were then multiplied 36 times by a combination of off-the-shelf millimeter- wave components, and JPL-built 200- GHz doublers and 300- and 600-GHz triplers. The power required to drive the submillimeter-wave multipliers was provided by JPL-built W-band amplifiers. The receive and transmit signal paths were combined using a thin, high-resistivity silicon wafer as a beam splitter. While the results at present are encouraging, the system still lacks sufficient speed to be usable for practical applications in a contraband detection. Ideally, an image acquisition speed of ten seconds, or a factor of 30 improvement, is desired. However, the system improvements to date have resulted in a factor of five increase in signal acquisition speed, as well as enhanced signal processing algorithms, permitting clearer imaging of contraband objects hidden underneath clothing. In particular, advances in three distinct areas have enabled these performance enhancements: base source phase noise reduction, chirp rate, and signal processing. Additionally, a second pixel was added, automatically reducing the imaging time by a factor of two. Although adding a second pixel to the system doubles the amount of submillimeter components required, some savings in microwave hardware can be realized by using a common low-noise source.

Activity Monitors Step Count Accuracy in Community-Dwelling Older Adults.

PubMed

Johnson, Marquell

2015-01-01

Objective: To examine the step count accuracy of activity monitors in community-dwelling older adults. Method : Twenty-nine participants aged 67.70 ± 6.07 participated. Three pedometers and the Actical accelerometer step count functions were compared with actual steps taken during a 200-m walk around an indoor track and during treadmill walking at three different speeds. Results : There was no statistical difference between activity monitors step counts and actual steps during self-selected pace walking. During treadmill walking at 0.67 m∙s -1 , all activity monitors step counts were significantly different from actual steps. During treadmill walking at 0.894m∙s -1 , the Omron HJ-112 pedometer step counts were not significantly different from actual steps. During treadmill walking at 1.12 m∙s -1 , the Yamax SW-200 pedometer steps were significantly different from actual steps. Discussion : Activity monitor selection should be deliberate when examining the walking behaviors of community-dwelling older adults, especially for those who walk at a slower pace.

Activity Monitors Step Count Accuracy in Community-Dwelling Older Adults

PubMed Central

2015-01-01

Objective: To examine the step count accuracy of activity monitors in community-dwelling older adults. Method: Twenty-nine participants aged 67.70 ± 6.07 participated. Three pedometers and the Actical accelerometer step count functions were compared with actual steps taken during a 200-m walk around an indoor track and during treadmill walking at three different speeds. Results: There was no statistical difference between activity monitors step counts and actual steps during self-selected pace walking. During treadmill walking at 0.67 m∙s−1, all activity monitors step counts were significantly different from actual steps. During treadmill walking at 0.894m∙s−1, the Omron HJ-112 pedometer step counts were not significantly different from actual steps. During treadmill walking at 1.12 m∙s−1, the Yamax SW-200 pedometer steps were significantly different from actual steps. Discussion: Activity monitor selection should be deliberate when examining the walking behaviors of community-dwelling older adults, especially for those who walk at a slower pace. PMID:28138464

Application of velocity filtering to optical-flow passive ranging

NASA Technical Reports Server (NTRS)

Barniv, Yair

1992-01-01

The performance of the velocity filtering method as applied to optical-flow passive ranging under real-world conditions is evaluated. The theory of the 3-D Fourier transform as applied to constant-speed moving points is reviewed, and the space-domain shift-and-add algorithm is derived from the general 3-D matched filtering formulation. The constant-speed algorithm is then modified to fit the actual speed encountered in the optical flow application, and the passband of that filter is found in terms of depth (sensor/object distance) so as to cover any given range of depths. Two algorithmic solutions for the problems associated with pixel interpolation and object expansion are developed, and experimental results are presented.

Wind Speed Perception and Risk

PubMed Central

Agdas, Duzgun; Webster, Gregory D.; Masters, Forrest J.

2012-01-01

Background How accurately do people perceive extreme wind speeds and how does that perception affect the perceived risk? Prior research on human–wind interaction has focused on comfort levels in urban settings or knock-down thresholds. No systematic experimental research has attempted to assess people's ability to estimate extreme wind speeds and perceptions of their associated risks. Method We exposed 76 people to 10, 20, 30, 40, 50, and 60 mph (4.5, 8.9, 13.4, 17.9, 22.3, and 26.8 m/s) winds in randomized orders and asked them to estimate wind speed and the corresponding risk they felt. Results Multilevel modeling showed that people were accurate at lower wind speeds but overestimated wind speeds at higher levels. Wind speed perceptions mediated the direct relationship between actual wind speeds and perceptions of risk (i.e., the greater the perceived wind speed, the greater the perceived risk). The number of tropical cyclones people had experienced moderated the strength of the actual–perceived wind speed relationship; consequently, mediation was stronger for people who had experienced fewer storms. Conclusion These findings provide a clearer understanding of wind and risk perception, which can aid development of public policy solutions toward communicating the severity and risks associated with natural disasters. PMID:23226230

Accuracy of physical activity monitors in pregnant women.

PubMed

Connolly, Christopher P; Coe, Dawn P; Kendrick, Jo M; Bassett, David R; Thompson, Dixie L

2011-06-01

To determine the step count accuracy of three pedometers and one accelerometer in pregnant women during treadmill walking. Participants were 30 women in the second or third trimester (20-34 wk) who were screened for pregnancy-related risk factors. Each participant was fitted with a belt containing three physical activity monitors: Yamax Digiwalker SW-200 (DW), New Lifestyles NL 2000 (NL), and GT3X ActiGraph accelerometer (ACT). The Omron HJ-720ITC (HJ) was placed in the pants' front pocket. Participants walked at 54, 67, 80, and 94 m · min for 2 min each. Actual steps were determined by an investigator using a hand-tally counter. The mean percent of steps recorded was calculated for each device at each speed and compared. Pearson correlations were used to determine the effect of body mass index and tilt angle on pedometer accuracy. There was a significant interaction between speed and device (F9,20 = 7.574, P < 0.001). Across all speeds, the NL and HJ had the lowest error. The ACT and DW underestimated the actual steps taken, particularly at the slower walking speeds. At 54 m · min, the ACT averaged 77.5% of steps and the DW averaged 56.9% of steps. Significant differences in the mean percent of steps recorded were found between devices at all speeds. Body mass index was only significantly correlated with percent of steps recorded by the NL, and there were no significant correlations between steps recorded and tilt angle. In pregnant women, the ACT and DW had more error than the NL and HJ. On the basis of these results, the NL and HJ should be considered for use in further research studies and physical activity programs that focus on walking during pregnancy.

Managing coherence via put/get windows

DOEpatents

Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton on Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Philip [Cortlandt Manor, NY; Hoenicke, Dirk [Ossining, NY; Ohmacht, Martin [Yorktown Heights, NY

2011-01-11

A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an area of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.

Managing coherence via put/get windows

DOEpatents

Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton on Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Philip [Cortlandt Manor, NY; Hoenicke, Dirk [Ossining, NY; Ohmacht, Martin [Yorktown Heights, NY

2012-02-21

A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an area of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.

ADHD symptoms and benefit from extended time testing accommodations.

PubMed

Lovett, Benjamin J; Leja, Ashley M

2015-02-01

To investigate the relationship between ADHD symptoms, executive functioning problems, and benefit from extended time testing accommodations. College students completed a battery of measures assessing processing speed and reading fluency, reading comprehension (under two different time limits), symptoms of ADHD, executive functioning deficits, and perceptions of need for extended time. Students reporting more symptoms of ADHD and executive functioning deficits actually benefited less from extended time, and students' perceptions of their timing needs did not predict benefit. Students with more ADHD symptoms are less likely to use extended time effectively, possibly because of their associated executive functioning problems. These results suggest there may be little justification for examining a student's ADHD symptoms when making extended time accommodation decisions. © 2013 SAGE Publications.

Speed, Dissipation, and Accuracy in Early T-cell Recognition

NASA Astrophysics Data System (ADS)

Cui, Wenping; Mehta, Pankaj

In the immune system, T cells can perform self-foreign discrimination with great foreign ligand sensitivity, high decision speed and low energy cost. There is significant evidence T-cells achieve such great performance with a mechanism: kinetic proofreading(KPR). KPR-based mechanisms actively consume energy to increase the specificity of T-cell recognition. An important theoretical question arises: how to understand trade-offs and fundamental limits on accuracy, speed, and dissipation (energy consumption). Recent theoretical work suggests that it is always possible to reduce the the error of KPR-based mechanisms by waiting longer and/or consuming more energy. Surprisingly, we find that this is not the case and that there actually exists an optimal point in the speed-energy-accuracy plane for KPR and its generalizations. This work was supported by NIH R35 and Simons MMLS Grant.

An advanced robust method for speed control of switched reluctance motor

NASA Astrophysics Data System (ADS)

Zhang, Chao; Ming, Zhengfeng; Su, Zhanping; Cai, Zhuang

2018-05-01

This paper presents an advanced robust controller for the speed system of a switched reluctance motor (SRM) in the presence of nonlinearities, speed ripple, and external disturbances. It proposes that the adaptive fuzzy control is applied to regulate the motor speed in the outer loop, and the detector is used to obtain rotor detection in the inner loop. The new fuzzy logic tuning rules are achieved from the experience of the operator and the knowledge of the specialist. The fuzzy parameters are automatically adjusted online according to the error and its change of speed in the transient period. The designed detector can obtain the rotor's position accurately in each phase module. Furthermore, a series of contrastive simulations are completed between the proposed controller and proportion integration differentiation controller including low speed, medium speed, and high speed. Simulations show that the proposed robust controller enables the system reduced by at least 3% in overshoot, 6% in rise time, and 20% in setting time, respectively, and especially under external disturbances. Moreover, an actual SRM control system is constructed at 220 V 370 W. The experiment results further prove that the proposed robust controller has excellent dynamic performance and strong robustness.

Stardust Interstellar Preliminary Examination IX: High-Speed Interstellar Dust Analog Capture in Stardust Flight-Spare Aerogel

NASA Technical Reports Server (NTRS)

Postberg, F.; Sterken, V.; Achilles, C.; Allen, C.; Bastien, R. K.; Frank, D.; Sandford, S. A.; Zolensky, M. E.; Butterworth, A.; Gainesforth, Z.

2014-01-01

The NASA Stardust mission used silica aerogel slabs to slowly decelerate and capture impinging cosmic dust particles for return to Earth. During this process, impact tracks are generated along the trajectory of the particle into the aerogel. It is believed that the morphology and dimensions of these tracks, together with the state of captured grains at track termini, may be linked to the size, velocity, and density of the impacting cosmic dust grain. Here, we present the results of laboratory hypervelocity impact experiments, during which cosmic dust analog particles (diameters of between 0.2 and 0.4 lm), composed of olivine, orthopyroxene, or an organic polymer, were accelerated onto Stardust flight spare low-density (approximately 0.01 g/cu cm) silica aerogel. The impact velocities (3-21 km/s) were chosen to simulate the range of velocities expected during Stardust's interstellar dust (ISD) collection phases. Track lengths and widths, together with the success of particle capture, are analyzed as functions of impact velocity and particle composition, density, and size. Captured terminal particles from low-density organic projectiles become undetectable at lower velocities than those from similarly sized, denser mineral particles, which are still detectable (although substantially altered by the impact process) at 15 km/s. The survival of these terminal particles, together with the track dimensions obtained during low impact speed capture of small grains in the laboratory, indicates that two of the three best Stardust candidate extraterrestrial grains were actually captured at speeds much lower than predicted. Track length and diameters are, in general, more sensitive to impact velocities than previously expected, which makes tracks of particles with diameters of 0.4 lm and below hard to identify at low capture speeds (<10 km/s). Therefore, although captured intact, the majority of the interstellar dust grains returned to Earth by Stardust remain to be found.

Laser-aided Directed Metal Deposition of Ni-based superalloy powder

NASA Astrophysics Data System (ADS)

Caiazzo, Fabrizia

2018-07-01

The subject of repairing Ni-based parts with state-of-the-art technologies is increasingly addressed both for research and industrial purposes, aiming to cost saving mainly in aerospace and automotive. In this frame, laser-aided Directed Metal Deposition (DMD) with injection of powder is investigated in this paper since minimal distortion of the work-piece, reduced heat-affected zones and better surface quality are benefited in comparison with conventional techniques. Actual application to overhaul Ni-based components is aimed, therefore homologous powder is fed by means of a 3-way feeding nozzle over the substrate; a disc laser is used as heat source. The chemical composition of both the substrate and the powder is preliminarily investigated via areal and punctual EDS inspections. A 2-factor, 2-level experimental plan is drawn to discuss the main effects of the processing variables laser power and processing speed. Namely, the resulting trends are given and compared with similar findings in the literature. Interestingly, dilution as a measure of metal affection is found to be lower than 25%, hence the operating window is deemed to be suitable for both repairing and fabrication of parts. Eventually, repairing by means of side overlapping and multi-level deposition traces on artificial square-shaped grooves is performed: indeed, similar slots are made before DMD to preliminarily remove any local imperfection upon improper casting of the part in the actual industrial process. Although a number of micropores are found, the process is deemed to comply with usual referred standards; in particular, a proper processing window has been found to prevent the occurrence of hot cracking which usually affects the compliance to stress.

The Development of a 3D LADAR Simulator Based on a Fast Target Impulse Response Generation Approach

NASA Astrophysics Data System (ADS)

Al-Temeemy, Ali Adnan

2017-09-01

A new laser detection and ranging (LADAR) simulator has been developed, using MATLAB and its graphical user interface, to simulate direct detection time of flight LADAR systems, and to produce 3D simulated scanning images under a wide variety of conditions. This simulator models each stage from the laser source to data generation and can be considered as an efficient simulation tool to use when developing LADAR systems and their data processing algorithms. The novel approach proposed for this simulator is to generate the actual target impulse response. This approach is fast and able to deal with high scanning requirements without losing the fidelity that accompanies increments in speed. This leads to a more efficient LADAR simulator and opens up the possibility for simulating LADAR beam propagation more accurately by using a large number of laser footprint samples. The approach is to select only the parts of the target that lie in the laser beam angular field by mathematically deriving the required equations and calculating the target angular ranges. The performance of the new simulator has been evaluated under different scanning conditions, the results showing significant increments in processing speeds in comparison to conventional approaches, which are also used in this study as a point of comparison for the results. The results also show the simulator's ability to simulate phenomena related to the scanning process, for example, type of noise, scanning resolution and laser beam width.

Use of schlieren methods to study gas flow in laser technology

NASA Astrophysics Data System (ADS)

Mrňa, Libor; Pavelka, Jan; Horník, Petr; Hrabovský, Jozef

2016-11-01

Laser technologies such as welding and cutting rely on process gases. We suggest to use schlieren imaging to visualize the gas flow during these processes. During the process of laser welding, the shielding gas flows to the welded area to prevent oxidation of the weld pool by surrounding air. The gas also interacts with hot plasma spurting from the key hole induced by the laser beam incident on the molten material. This interaction is quite complicated because hot plasma mixes with the cold shielding gas while the system is moving along the weld. Three shielding gases were used in the presented experiment: Ar, He and N2. Differences in dynamics of the flow are clearly visible on schlieren images. Moreover, high speed recording reveals a structure consisting of hot gas bubbles. We were also able to determine the velocity of the bubbles from the recording. During laser cutting, the process gas flows coaxially with the laser beam from the nozzle to remove the molten material out of the kerf. The gas flow is critical for the quality of the resulting edge of the cut. Schlieren method was used to study gas flow under the nozzle and then under the material being cut. This actually creates another slot nozzle. Due to the very low speed of flow below the material the schleiren method is already at the limit of its sensitivity. Therefore, it is necessary to apply a differential technique to increase the contrast. Distinctive widening of the flow shaped by the kerf was observed.

How much time do drivers need to obtain situation awareness? A laboratory-based study of automated driving.

PubMed

Lu, Zhenji; Coster, Xander; de Winter, Joost

2017-04-01

Drivers of automated cars may occasionally need to take back manual control after a period of inattentiveness. At present, it is unknown how long it takes to build up situation awareness of a traffic situation. In this study, 34 participants were presented with animated video clips of traffic situations on a three-lane road, from an egocentric viewpoint on a monitor equipped with eye tracker. Each participant viewed 24 videos of different durations (1, 3, 7, 9, 12, or 20 s). After each video, participants reproduced the end of the video by placing cars in a top-down view, and indicated the relative speeds of the placed cars with respect to the ego-vehicle. Results showed that the longer the video length, the lower the absolute error of the number of placed cars, the lower the total distance error between the placed cars and actual cars, and the lower the geometric difference between the placed cars and the actual cars. These effects appeared to be saturated at video lengths of 7-12 s. The total speed error between placed and actual cars also reduced with video length, but showed no saturation up to 20 s. Glance frequencies to the mirrors decreased with observation time, which is consistent with the notion that participants first estimated the spatial pattern of cars after which they directed their attention to individual cars. In conclusion, observers are able to reproduce the layout of a situation quickly, but the assessment of relative speeds takes 20 s or more. Copyright © 2016 Elsevier Ltd. All rights reserved.

Prefrontal cortex activity during response selection predicts processing speed impairment in schizophrenia

PubMed Central

Woodward, Neil D.; Duffy-Alberto, Brittney; Karbasforoushan, Haleh

2014-01-01

Processing speed is the most impaired neuropsychological domain in schizophrenia and a robust predictor of functional outcome. Determining the specific cognitive operations underlying processing speed dysfunction and indentifying their neural correlates may assist in developing pro-cognitive interventions. Response selection, the process of mapping stimuli onto motor responses, correlates with neuropsychological tests of processing speed and may contribute to processing speed impairment in schizophrenia. This study investigated the relationship between behavioral and neural measures of response selection, and a neuropsychological index of processing speed in schizophrenia. 26 patients with schizophrenia and 21 healthy subjects underwent fMRI scanning during performance of 2 and 4-choice-reaction time (RT) tasks and completed the Wechsler Adult Intelligence Scale-III (WAIS) Processing Speed Index (PSI). Response selection, defined as RT slowing between 2 and 4-choice RT, was impaired in schizophrenia and correlated with psychometric processing speed. Greater activation of the dorsolateral prefrontal cortex (PFC) was observed in schizophrenia and correlated with poorer WAIS PSI scores. Deficient response selection and abnormal recruitment of the dorsolateral PFC during response selection contribute to processing speed impairment in schizophrenia. Interventions that improve response selection and normalize dorsolateral PFC function may improve processing speed in schizophrenia. PMID:23816240

Working memory influences processing speed and reading fluency in ADHD.

PubMed

Jacobson, Lisa A; Ryan, Matthew; Martin, Rebecca B; Ewen, Joshua; Mostofsky, Stewart H; Denckla, Martha B; Mahone, E Mark

2011-01-01

Processing-speed deficits affect reading efficiency, even among individuals who recognize and decode words accurately. Children with ADHD who decode words accurately can still have inefficient reading fluency, leading to a bottleneck in other cognitive processes. This "slowing" in ADHD is associated with deficits in fundamental components of executive function underlying processing speed, including response selection. The purpose of the present study was to deconstruct processing speed in order to determine which components of executive control best explain the "processing" speed deficits related to reading fluency in ADHD. Participants (41 ADHD, 21 controls), ages 9-14 years, screened for language disorders, word reading deficits, and psychiatric disorders, were administered measures of copying speed, processing speed, reading fluency, working memory, reaction time, inhibition, and auditory attention span. Compared to controls, children with ADHD showed reduced oral and silent reading fluency and reduced processing speed-driven primarily by deficits on WISC-IV Coding. In contrast, groups did not differ on copying speed. After controlling for copying speed, sex, severity of ADHD-related symptomatology, and GAI, slowed "processing" speed (i.e., Coding) was significantly associated with verbal span and measures of working memory but not with measures of response control/inhibition, lexical retrieval speed, reaction time, or intrasubject variability. Further, "processing" speed (i.e., Coding, residualized for copying speed) and working memory were significant predictors of oral reading fluency. Abnormalities in working memory and response selection (which are frontally mediated and enter into the output side of processing speed) may play an important role in deficits in reading fluency in ADHD, potentially more than posteriorally mediated problems with orienting of attention or perceiving the stimulus.

Field experiments to determine wave propagation principles and mechanical properties of snow

NASA Astrophysics Data System (ADS)

Simioni, Stephan; Gebhard, Felix; Dual, Jürg; Schweizer, Jürg

2017-04-01

To understand the release of snow avalanches by explosions one needs to know how acoustic waves travel above and within the snowpack. Hitherto, wave propagation was investigated in the laboratory with small samples or in the field in the shock wave region. We developed a measurement system and layout to derive wave attenuation in snow, wave speeds and elastic moduli on small-scale (1-2 m) field experiments to close the gap between the lab scale (0.1 m) and the scale of artificial release (10-100 m). We used solid explosives and hammer blows to create the load and accelerometers to measure the resulting wave within the snowpack. The strong attenuation we observed indicates that we measured the second longitudinal wave which propagates through the pore space. The wave speeds, however, corresponded to the speeds of the first longitudinal wave within the ice skeleton. The elastic moduli were high on the order of several tens of MPa for lower densities (150 kg m-3) and agreed well with earlier lab studies, in particular for the higher densities 250-400 kg m-3). However, the scatter was rather large as expected for in-situ experiments in the layered snow cover. In addition, we measured accelerations during propagation saw test experiments. The propagation of cracks during this type of snow instability test has mainly been studied by analysing the bending of the slab (due to the saw cut) using particle tracking velocimetry. We used the accelerometers to measure crack propagation speeds. The wave speeds were slightly higher for most experiments than reported previously. Furthermore, in some experiments, we encountered to different wave types with one propagating at a higher speed. This finding may be interpreted as the actual crack propagation and the settling of the weak layer (collapse wave). Our results show that field measurements of propagation properties are feasible and that crack propagation as observed during propagation saw tests may involve different processes that need to be further investigated.

Shelter Index and a simple wind speed parameter to characterize vegetation control of sand transport threshold and Flu

NASA Astrophysics Data System (ADS)

Gillies, J. A.; Nield, J. M.; Nickling, W. G.; Furtak-Cole, E.

2014-12-01

Wind erosion and dust emissions occur in many dryland environments from a range of surfaces with different types and amounts of vegetation. Understanding how vegetation modulates these processes remains a research challenge. Here we present results from a study that examines the relationship between an index of shelter (SI=distance from a point to the nearest upwind vegetation/vegetation height) and particle threshold expressed as the ratio of wind speed measured at 0.45 times the mean plant height divided by the wind speed at 17 m when saltation commences, and saltation flux. The results are used to evaluate SI as a parameter to characterize the influence of vegetation on local winds and sediment transport conditions. Wind speed, wind direction, saltation activity and point saltation flux were measured at 35 locations in defined test areas (~13,000 m2) in two vegetation communities: mature streets of mesquite covered nebkhas and incipient nebkhas dominated by low mesquite plants. Measurement positions represent the most open areas, and hence those places most susceptible to wind erosion among the vegetation elements. Shelter index was calculated for each measurement position for each 10° wind direction bin using digital elevation models for each site acquired using terrestrial laser scanning. SI can show the susceptibility to wind erosion at different time scales, i.e., event, seasonal, or annual, but in a supply-limited system it can fail to define actual flux amounts due to a lack of knowledge of the distribution of sediment across the surface of interest with respect to the patterns of SI.

A Pause-then-Cancel model of stopping: evidence from basal ganglia neurophysiology

PubMed Central

Berke, Joshua D.

2017-01-01

Many studies have implicated the basal ganglia in the suppression of action impulses (‘stopping’). Here, we discuss recent neurophysiological evidence that distinct hypothesized processes involved in action preparation and cancellation can be mapped onto distinct basal ganglia cell types and pathways. We examine how movement-related activity in the striatum is related to a ‘Go’ process and how going may be modulated by brief epochs of beta oscillations. We then describe how, rather than a unitary ‘Stop’ process, there appear to be separate, complementary ‘Pause’ and ‘Cancel’ mechanisms. We discuss the implications of these stopping subprocesses for the interpretation of the stop-signal reaction time—in particular, some activity that seems too slow to causally contribute to stopping when assuming a single Stop processes may actually be fast enough under a Pause-then-Cancel model. Finally, we suggest that combining complementary neural mechanisms that emphasize speed or accuracy respectively may serve more generally to optimize speed–accuracy trade-offs. This article is part of the themed issue ‘Movement suppression: brain mechanisms for stopping and stillness’. PMID:28242736

Assessing the economics of processing end-of-life vehicles through manual dismantling.

PubMed

Tian, Jin; Chen, Ming

2016-10-01

Most dismantling enterprises in a number of developing countries, such as China, usually adopt the "manual+mechanical" dismantling approach to process end-of-life vehicles. However, the automobile industry does not have a clear indicator to reasonably and effectively determine the manual dismantling degree for end-of-life vehicles. In this study, five different dismantling scenarios and an economic system for end-of-life vehicles were developed based on the actual situation of end-of-life vehicles. The fuzzy analytic hierarchy process was applied to set the weights of direct costs, indirect costs, and sales and to obtain an optimal manual dismantling scenario. Results showed that although the traditional method of "dismantling to the end" can guarantee the highest recycling rate, this method is not the best among all the scenarios. The profit gained in the optimal scenario is 100.6% higher than that in the traditional scenario. The optimal manual dismantling scenario showed that enterprises are required to select suitable parts to process through manual dismantling. Selecting suitable parts maximizes economic profit and improves dismantling speed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study the influence of formulation process parameters on solubility and dissolution enhancement of efavirenz solid solutions prepared by hot-melt extrusion: a QbD methodology.

PubMed

Pawar, Jaywant; Suryawanshi, Dilipkumar; Moravkar, Kailas; Aware, Rahul; Shetty, Vasant; Maniruzzaman, Mohammed; Amin, Purnima

2018-02-09

The current study investigates the dissolution rate performance of amorphous solid solutions of a poorly water-soluble drug, efavirenz (EFV), in amorphous Soluplus® (SOL) and Kollidon® VA 64 (KVA64) polymeric systems. For the purpose of the study, various formulations with varying drug loadings of 30, 50, and 70% w/w were developed via hot-melt extrusion processing and adopting a Box-Behnken design of experiment (DoE) approach. The polymers were selected based on the Hansen solubility parameter calculation and the prediction of the possible drug-polymer miscibility. In DoE experiments, a Box-Behnken factorial design was conducted to evaluate the effect of independent variables such as Soluplus® ratio (A 1 ), HME screw speed (A 2 ), and processing temperature (A 3 ), and Kollidon®VA64 ratio (B 1 ), screw speed (B 2 ), and processing temperature (B 3 ) on responses such as solubility (X 1 and Y 1 ) and dissolution rate (X 2 and Y 2 ) for both ASS [EFV:SOL] and BSS [EFV:KVA64] systems. DSC and XRD data confirmed that bulk crystalline EFV transformed to amorphous form during the HME processing. Advanced chemical analyses conducted via 2D COSY NMR, FTIR chemical imaging, AFM analysis, and FTIR showed that EFV was homogenously dispersed in the respective polymer matrices. The maximum solubility and dissolution rate was observed in formulations containing 30% EFV with both SOL and KVA64 alone. This could be attributed to the maximum drug-polymer miscibility in the optimized formulations. The actual and predicted values of both responses were found precise and close to each other.

Thought Speed, Mood, and the Experience of Mental Motion.

PubMed

Pronin, Emily; Jacobs, Elana

2008-11-01

This article presents a theoretical account relating thought speed to mood and psychological experience. Thought sequences that occur at a fast speed generally induce more positive affect than do those that occur slowly. Thought speed constitutes one aspect of mental motion. Another aspect involves thought variability, or the degree to which thoughts in a sequence either vary widely from or revolve closely around a theme. Thought sequences possessing more motion (occurring fast and varying widely) generally produce more positive affect than do sequences possessing little motion (occurring slowly and repetitively). When speed and variability oppose each other, such that one is low and the other is high, predictable psychological states also emerge. For example, whereas slow, repetitive thinking can prompt dejection, fast, repetitive thinking can prompt anxiety. This distinction is related to the fact that fast thinking involves greater actual and felt energy than slow thinking does. Effects of mental motion occur independent of the specific content of thought. Their consequences for mood and energy hold psychotherapeutic relevance. © 2008 Association for Psychological Science.

Architecture and robustness tradeoffs in speed-scaled queues with application to energy management

NASA Astrophysics Data System (ADS)

Dinh, Tuan V.; Andrew, Lachlan L. H.; Nazarathy, Yoni

2014-08-01

We consider single-pass, lossless, queueing systems at steady-state subject to Poisson job arrivals at an unknown rate. Service rates are allowed to depend on the number of jobs in the system, up to a fixed maximum, and power consumption is an increasing function of speed. The goal is to control the state dependent service rates such that both energy consumption and delay are kept low. We consider a linear combination of the mean job delay and energy consumption as the performance measure. We examine both the 'architecture' of the system, which we define as a specification of the number of speeds that the system can choose from, and the 'design' of the system, which we define as the actual speeds available. Previous work has illustrated that when the arrival rate is precisely known, there is little benefit in introducing complex (multi-speed) architectures, yet in view of parameter uncertainty, allowing a variable number of speeds improves robustness. We quantify the tradeoffs of architecture specification with respect to robustness, analysing both global robustness and a newly defined measure which we call local robustness.

Additional road markings as an indication of speed limits: results of a field experiment and a driving simulator study.

PubMed

Daniels, Stijn; Vanrie, Jan; Dreesen, An; Brijs, Tom

2010-05-01

Although speed limits are indicated by road signs, road users are not always aware, while driving, of the actual speed limit on a given road segment. The Roads and Traffic Agency developed additional road markings in order to support driver decisions on speed on 70 km/h roads in Flanders-Belgium. In this paper the results are presented of two evaluation studies, both a field study and a simulator study, on the effects of the additional road markings on speed behaviour. The results of the field study showed no substantial effect of the markings on speed behaviour. Neither did the simulator study, with slightly different stimuli. Nevertheless an effect on lateral position was noticed in the simulator study, showing at least some effect of the markings. The role of conspicuity of design elements and expectations towards traffic environments is discussed. Both studies illustrate well some strengths and weaknesses of observational field studies compared to experimental simulator studies. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

[Design and Analysis of CT High-speed Data Transmission Rotating Connector Ring System Retaining Ring].

PubMed

Pan, Li; Cao, Jujiang; Liu, Min; Fu, Weiwei

2017-11-30

High speed data transmission rotating connector system for signal high-speed transmission used in the fixed end and rotating end, it is one of the core component in the CT system. This paper involves structure design and analysis of the retaining ring in the CT high speed data transmission rotating connector system based on the principle of off-axis free space optical transmission. According to the problem of the actual engineering application of space limitations, optical fiber fixed and collimator installation location, we designed the structure of the retaining ring. Using the static analysis function of ANSYS Workbench, it verifies rationality and safety of the strength of retaining ring structure. And based on modal analysis function of ANSYS Workbench, it evaluates the effect of the retaining ring on the stability of the system date transmission, and provides theoretical basis for the feasibility of the structure in practical application.

Mate Finding, Sexual Spore Production, and the Spread of Fungal Plant Parasites.

PubMed

Hamelin, Frédéric M; Castella, François; Doli, Valentin; Marçais, Benoît; Ravigné, Virginie; Lewis, Mark A

2016-04-01

Sexual reproduction and dispersal are often coupled in organisms mixing sexual and asexual reproduction, such as fungi. The aim of this study is to evaluate the impact of mate limitation on the spreading speed of fungal plant parasites. Starting from a simple model with two coupled partial differential equations, we take advantage of the fact that we are interested in the dynamics over large spatial and temporal scales to reduce the model to a single equation. We obtain a simple expression for speed of spread, accounting for both sexual and asexual reproduction. Taking Black Sigatoka disease of banana plants as a case study, the model prediction is in close agreement with the actual spreading speed (100 km per year), whereas a similar model without mate limitation predicts a wave speed one order of magnitude greater. We discuss the implications of these results to control parasites in which sexual reproduction and dispersal are intrinsically coupled.

Transcription profile of boar spermatozoa as revealed by RNA-sequencing

USDA-ARS?s Scientific Manuscript database

High-throughput RNA sequencing (RNA-Seq) overcomes the limitations of the current hybridization-based techniques to detect the actual pool of RNA transcripts in spermatozoa. The application of this technology in livestock can speed the discovery of potential predictors of male fertility. As a first ...

49 CFR 234.259 - Warning time.

Code of Federal Regulations, 2011 CFR

2011-10-01

... modified because of a change in train speeds. Electronic devices that accurately determine actual warning... 49 Transportation 4 2011-10-01 2011-10-01 false Warning time. 234.259 Section 234.259..., Inspection, and Testing Inspections and Tests § 234.259 Warning time. Each crossing warning system shall be...

49 CFR 234.259 - Warning time.

Code of Federal Regulations, 2010 CFR

2010-10-01

... modified because of a change in train speeds. Electronic devices that accurately determine actual warning... 49 Transportation 4 2010-10-01 2010-10-01 false Warning time. 234.259 Section 234.259..., Inspection, and Testing Inspections and Tests § 234.259 Warning time. Each crossing warning system shall be...

Using Dynamic Walking Models to Identify Factors that Contribute to Increased Risk of Falling in Older Adults

PubMed Central

Roos, Paulien E.; Dingwell, Jonathan B.

2013-01-01

Falls are common in older adults. The most common cause of falls is tripping while walking. Simulation studies demonstrated that older adults may be restricted by lower limb strength and movement speed to regain balance after a trip. This review examines how modeling approaches can be used to determine how different measures predict actual fall risk and what some of the causal mechanisms of fall risk are. Although increased gait variability predicts increased fall risk experimentally, it is not clear which variability measures could best be used, or what magnitude of change corresponded with increased fall risk. With a simulation study we showed that the increase in fall risk with a certain increase in gait variability was greatly influenced by the initial level of variability. Gait variability can therefore not easily be used to predict fall risk. We therefore explored other measures that may be related to fall risk and investigated the relationship between stability measures such as Floquet multipliers and local divergence exponents and actual fall risk in a dynamic walking model. We demonstrated that short-term local divergence exponents were a good early predictor for fall risk. Neuronal noise increases with age. It has however not been fully understood if increased neuronal noise would cause an increased fall risk. With our dynamic walking model we showed that increased neuronal noise caused increased fall risk. Although people who are at increased risk of falling reduce their walking speed it had been questioned whether this slower speed would actually cause a reduced fall risk. With our model we demonstrated that a reduced walking speed caused a reduction in fall risk. This may be due to the decreased kinematic variability as a result of the reduced signal-dependent noise of the smaller muscle forces that are required for slower. These insights may be used in the development of fall prevention programs in order to better identify those at increased risk of falling and to target those factors that influence fall risk most. PMID:24120280

Using dynamic walking models to identify factors that contribute to increased risk of falling in older adults.

PubMed

Roos, Paulien E; Dingwell, Jonathan B

2013-10-01

Falls are common in older adults. The most common cause of falls is tripping while walking. Simulation studies demonstrated that older adults may be restricted by lower limb strength and movement speed to regain balance after a trip. This review examines how modeling approaches can be used to determine how different measures predict actual fall risk and what some of the causal mechanisms of fall risk are. Although increased gait variability predicts increased fall risk experimentally, it is not clear which variability measures could best be used, or what magnitude of change corresponded with increased fall risk. With a simulation study we showed that the increase in fall risk with a certain increase in gait variability was greatly influenced by the initial level of variability. Gait variability can therefore not easily be used to predict fall risk. We therefore explored other measures that may be related to fall risk and investigated the relationship between stability measures such as Floquet multipliers and local divergence exponents and actual fall risk in a dynamic walking model. We demonstrated that short-term local divergence exponents were a good early predictor for fall risk. Neuronal noise increases with age. It has however not been fully understood if increased neuronal noise would cause an increased fall risk. With our dynamic walking model we showed that increased neuronal noise caused increased fall risk. Although people who are at increased risk of falling reduce their walking speed it had been questioned whether this slower speed would actually cause a reduced fall risk. With our model we demonstrated that a reduced walking speed caused a reduction in fall risk. This may be due to the decreased kinematic variability as a result of the reduced signal-dependent noise of the smaller muscle forces that are required for slower. These insights may be used in the development of fall prevention programs in order to better identify those at increased risk of falling and to target those factors that influence fall risk most. Copyright © 2013 Elsevier B.V. All rights reserved.

Geokinetic Effects on Motion Sensitive Instrumentation, Systems and Facilities.

DTIC Science & Technology

1984-01-15

used to predict the responses for actual hammer-blows. Tiltmeter data from truck runs were frequency scaled to enable comparison to a common vehicle...to pressure loads traveling near the speed of sound in air was established. The RRV station was again occupied in June 1981 and tiltmeters and

Doppler and the Doppler Effect.

DTIC Science & Technology

1984-06-01

that "if the orbital speed of the earth would be ten times its actual value, all fixed stars in the eastern part of the ecliptic would, without...ionosphere by vertical and oblique high-frequency ionospheric soundings. This is illustrated in Figure 1. Over a 24-hour period, signal amplitudes and

Spread prediction model of continuous steel tube based on BP neural network

NASA Astrophysics Data System (ADS)

Zhai, Jian-wei; Yu, Hui; Zou, Hai-bei; Wang, San-zhong; Liu, Li-gang

2017-07-01

According to the geometric pass of roll and technological parameters of three-roller continuous mandrel rolling mill in a factory, a finite element model is established to simulate the continuous rolling process of seamless steel tube, and the reliability of finite element model is verified by comparing with the simulation results and actual results of rolling force, wall thickness and outer diameter of the tube. The effect of roller reduction, roller rotation speed and blooming temperature on the spread rule is studied. Based on BP(Back Propagation) neural network technology, a spread prediction model of continuous rolling tube is established for training wall thickness coefficient and spread coefficient of the continuous rolling tube, and the rapid and accurate prediction of continuous rolling tube size is realized.

An intelligent system with EMG-based joint angle estimation for telemanipulation.

PubMed

Suryanarayanan, S; Reddy, N P; Gupta, V

1996-01-01

Bio-control of telemanipulators is being researched as an alternate control strategy. This study investigates the use of surface EMG from the biceps to predict joint angle during flexion of the arm that can be used to control an anthropomorphic telemanipulator. An intelligent system based on neural networks and fuzzy logic has been developed to use the processed surface EMG signal and predict the joint angle. The system has been tested on various angles of flexion-extension of the arm and at several speeds of flexion-extension. Preliminary results show the RMS error between the predicted angle and the actual angle to be less than 3% during training and less than 15% during testing. The technique of direct bio-control using EMG has the potential as an interface for telemanipulation applications.

Telemetry data via communications relay

NASA Astrophysics Data System (ADS)

Strock, O. J.; Witchey, Michael

This paper responds to a test range engineer's need to relay one or more channels of various types of telemetry data from a remotely-located receiving station to the central telemetry station at range headquarters for real-time processing and display. Several types of data are identified, and specific equipment and technology for multiplexing, transmission, and demultiplexing up to eight streams from a variety of sources is discussed. The widely-used T3 communications link, also known as DS-3, can relay data via satellite, microwave link, or other high-speed path at 44.736 megabits per second, of which about 95 percent can be actual telemetry data; other standard links operate at lower aggregate rates. Several links and rates are discussed, with emphasis in the high-rate T3 link.

Managing coherence via put/get windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blumrich, Matthias A; Chen, Dong; Coteus, Paul W

A method and apparatus for managing coherence between two processors of a two processor node of a multi-processor computer system. Generally the present invention relates to a software algorithm that simplifies and significantly speeds the management of cache coherence in a message passing parallel computer, and to hardware apparatus that assists this cache coherence algorithm. The software algorithm uses the opening and closing of put/get windows to coordinate the activated required to achieve cache coherence. The hardware apparatus may be an extension to the hardware address decode, that creates, in the physical memory address space of the node, an areamore » of virtual memory that (a) does not actually exist, and (b) is therefore able to respond instantly to read and write requests from the processing elements.« less

A novel method for routine quality assurance of volumetric-modulated arc therapy.

PubMed

Wang, Qingxin; Dai, Jianrong; Zhang, Ke

2013-10-01

Volumetric-modulated arc therapy (VMAT) is delivered through synchronized variation of gantry angle, dose rate, and multileaf collimator (MLC) leaf positions. The delivery dynamic nature challenges the parameter setting accuracy of linac control system. The purpose of this study was to develop a novel method for routine quality assurance (QA) of VMAT linacs. ArcCheck is a detector array with diodes distributing in spiral pattern on cylindrical surface. Utilizing its features, a QA plan was designed to strictly test all varying parameters during VMAT delivery on an Elekta Synergy linac. In this plan, there are 24 control points. The gantry rotates clockwise from 181° to 179°. The dose rate, gantry speed, and MLC positions cover their ranges commonly used in clinic. The two borders of MLC-shaped field seat over two columns of diodes of ArcCheck when the gantry rotates to the angle specified by each control point. The ratio of dose rate between each of these diodes and the diode closest to the field center is a certain value and sensitive to the MLC positioning error of the leaf crossing the diode. Consequently, the positioning error can be determined by the ratio with the help of a relationship curve. The time when the gantry reaches the angle specified by each control point can be acquired from the virtual inclinometer that is a feature of ArcCheck. The gantry speed between two consecutive control points is then calculated. The aforementioned dose rate is calculated from an acm file that is generated during ArcCheck measurements. This file stores the data measured by each detector in 50 ms updates with each update in a separate row. A computer program was written in MATLAB language to process the data. The program output included MLC positioning errors and the dose rate at each control point as well as the gantry speed between control points. To evaluate this method, this plan was delivered for four consecutive weeks. The actual dose rate and gantry speed were compared with the QA plan specified. Additionally, leaf positioning errors were intentionally introduced to investigate the sensitivity of this method. The relationship curves were established for detecting MLC positioning errors during VMAT delivery. For four consecutive weeks measured, 98.4%, 94.9%, 89.2%, and 91.0% of the leaf positioning errors were within ± 0.5 mm, respectively. For the intentionally introduced leaf positioning systematic errors of -0.5 and +1 mm, the detected leaf positioning errors of 20 Y1 leaf were -0.48 ± 0.14 and 1.02 ± 0.26 mm, respectively. The actual gantry speed and dose rate closely followed the values specified in the VMAT QA plan. This method can assess the accuracy of MLC positions and the dose rate at each control point as well as the gantry speed between control points at the same time. It is efficient and suitable for routine quality assurance of VMAT.

Study on parameters affecting the mechanical properties of dry fiber bundles during continuous composite manufacturing processes

NASA Astrophysics Data System (ADS)

Maier, A.; Schledjewski, R.

2016-07-01

For continuous manufacturing processes mechanical preloading of the fibers occurs during the delivery of the fibers from the spool creel to the actual manufacturing process step. Moreover preloading of the dry roving bundles might be mandatory, e.g. during winding, to be able to produce high quality components. On the one hand too high tensile loads within dry roving bundles might result in a catastrophic failure and on the other hand the part produced under too low pre-tension might have low quality and mechanical properties. In this work, load conditions influencing mechanical properties of dry glass fiber bundles during continuous composite manufacturing processes were analyzed. Load conditions, i.e. fiber delivery speed, necessary pre-tension and other effects of the delivery system during continuous fiber winding, were chosen in process typical ranges. First, the strain rate dependency under static tensile load conditions was investigated. Furthermore different free gauge lengths up to 1.2 m, interactions between fiber points of contact regarding influence of sizing as well as impregnation were tested and the effect of twisting on the mechanical behavior of dry glass fiber bundles during the fiber delivery was studied.

Modeling of fugitive dust emission for construction sand and gravel processing plant.

PubMed

Lee, C H; Tang, L W; Chang, C T

2001-05-15

Due to rapid economic development in Taiwan, a large quantity of construction sand and gravel is needed to support domestic civil construction projects. However, a construction sand and gravel processing plant is often a major source of air pollution, due to its associated fugitive dust emission. To predict the amount of fugitive dust emitted from this kind of processing plant, a semiempirical model was developed in this study. This model was developed on the basis of the actual dust emission data (i.e., total suspended particulate, TSP) and four on-site operating parameters (i.e., wind speed (u), soil moisture (M), soil silt content (s), and number (N) of trucks) measured at a construction sand and gravel processing plant. On the basis of the on-site measured data and an SAS nonlinear regression program, the expression of this model is E = 0.011.u2.653.M-1.875.s0.060.N0.896, where E is the amount (kg/ton) of dust emitted during the production of each ton of gravel and sand. This model can serve as a facile tool for predicting the fugitive dust emission from a construction sand and gravel processing plant.

Working Memory Influences Processing Speed and Reading Fluency in ADHD

PubMed Central

Jacobson, Lisa A.; Ryan, Matthew; Martin, Rebecca B.; Ewen, Joshua; Mostofsky, Stewart H.; Denckla, Martha B.; Mahone, E. Mark

2012-01-01

Processing speed deficits affect reading efficiency, even among individuals who recognize and decode words accurately. Children with ADHD who decode words accurately can still have inefficient reading fluency, leading to a bottleneck in other cognitive processes. This “slowing” in ADHD is associated with deficits in fundamental components of executive function underlying processing speed, including response selection. The purpose of the present study was to deconstruct processing speed in order to determine which components of executive control best explain the “processing” speed deficits related to reading fluency in ADHD. Participants (41 ADHD, 21 controls), ages 9-14, screened for language disorders, word reading deficits, and psychiatric disorders, were administered measures of copying speed, processing speed, reading fluency, working memory, reaction time, inhibition, and auditory attention span. Compared to controls, children with ADHD showed reduced oral and silent reading fluency, and reduced processing speed—driven primarily by deficits on WISC-IV Coding. In contrast, groups did not differ on copying speed. After controlling for copying speed, sex, severity of ADHD-related symptomatology, and GAI, slowed “processing” speed (i.e., Coding) was significantly associated with verbal span and measures of working memory, but not with measures of response control/inhibition, lexical retrieval speed, reaction time, or intra-subject variability. Further, “processing” speed (i.e., Coding, residualized for copying speed) and working memory were significant predictors of oral reading fluency. Abnormalities in working memory and response selection (which are frontally-mediated and enter into the output side of processing speed) may play an important role in deficits in reading fluency in ADHD, potentially more than posteriorally-mediated problems with orienting of attention or perceiving the stimulus. PMID:21287422

Deceleration system for kinematic linkages of positioning

NASA Astrophysics Data System (ADS)

Stan, G.

2017-08-01

Flexible automation is used more and more in various production processes, so that both machining itself on CNC machine tools and workpiece handling means are performed through programming the needed working cycle. In order to obtain a successful precise positioning, each motion degree needs a certain deceleration before stopping at a programmed point. The increase of motion speed of moving elements within the manipulators structure depends directly on deceleration duty quality before the programmed stop. Proportional valves as well as servo-valves that can perform hydraulic decelerations are well known, but they feature several disadvantages, such as: high price, severe conditions for oil filtering and low reliability under industrial conditions. This work presents a new deceleration system that allows adjustment of deceleration slope according to actual conditions: inertial mass, speed etc. The new solution of hydraulic decelerator allows its integration to a position loop or its usage in case of positioning large elements that only perform fixed cycles. The results being obtained on the positioning accuracy of a linear axis using the new solution of the hydraulic decelerator are presented, too. The price of the new deceleration system is much lower compared to the price of proportional valves or servo-valves.

Mechanics of torque generation in the bacterial flagellar motor.

PubMed

Mandadapu, Kranthi K; Nirody, Jasmine A; Berry, Richard M; Oster, George

2015-08-11

The bacterial flagellar motor (BFM) is responsible for driving bacterial locomotion and chemotaxis, fundamental processes in pathogenesis and biofilm formation. In the BFM, torque is generated at the interface between transmembrane proteins (stators) and a rotor. It is well established that the passage of ions down a transmembrane gradient through the stator complex provides the energy for torque generation. However, the physics involved in this energy conversion remain poorly understood. Here we propose a mechanically specific model for torque generation in the BFM. In particular, we identify roles for two fundamental forces involved in torque generation: electrostatic and steric. We propose that electrostatic forces serve to position the stator, whereas steric forces comprise the actual "power stroke." Specifically, we propose that ion-induced conformational changes about a proline "hinge" residue in a stator α-helix are directly responsible for generating the power stroke. Our model predictions fit well with recent experiments on a single-stator motor. The proposed model provides a mechanical explanation for several fundamental properties of the flagellar motor, including torque-speed and speed-ion motive force relationships, backstepping, variation in step sizes, and the effects of key mutations in the stator.

Some new tests at the Gottingen laboratory

NASA Technical Reports Server (NTRS)

1921-01-01

The tests at the Gottingen laboratory included: friction tests on a surface treated with omelette, verification tests on the M.V.A. 356 wing, and comparative tests of wing no. 36 at the Eiffel laboratory. The examination of all these experiments leads to the belief that, at large incidences, the speeds registered by the suction manometer of the testing chamber of the Eiffel laboratory wind tunnel are, owing to pressure drop, greater than the actual speeds. Therefore, the values of k(sub x) and k(sub y) measured at the Eiffel laboratory at large incidences are too low.

Quantum Mechanics, vacuum, particles, Gödel-Cohen incompleteness and the Universe

NASA Astrophysics Data System (ADS)

Gonzalez-Mestres, Luis

2017-12-01

Are the standard laws of Physics really fundamental principles? Does the physical vacuum have a more primordial internal structure? Are quarks, leptons, gauge bosons… ultimate elementary objects? These three basic questions are actually closely related. If the deep vacuum structure and dynamics turn out to be less trivial than usually depicted, the conventional "elementary" particles will most likely be excitations of such a vacuum dynamics that remains by now unknown. We then expect relativity and quantum mechanics to be low-energy limits of a more fundamental dynamical pattern that generates them at a deeper level. It may even happen that vacuum drives the expansion of the Universe from its own inner dynamics. Inside such a vacuum structure, the speed of light would not be the critical speed for vacuum constituents and propagating signals. The natural scenario would be the superbradyon (superluminal preon) pattern we postulated in 1995, with a new critical speed cs much larger than the speed of light c just as c is much larger than the speed of sound. Superbradyons are assumed to be the bradyons of a super-relativity associated to cs (a Lorentz invariance with cs as the critical speed). Similarly, the standard relativistic space-time with four real coordinates would not necessarily hold beyond low-energy and comparatively local distance scales. Instead, the spinorial space-time (SST) with two complex coordinates we introduced in 1996-97 may be the suitable one to describe the internal structure of vacuum and standard "elementary" particles and, simultaneously, Cosmology at very large distance scales. If the constituents of the preonic vacuum are superluminal, quantum entanglement appears as a natural property provided cs ≫ c . The value of cs can even be possibly found experimentally by studying entanglement at large distances. It is not excluded that preonic constituents of vacuum can exist in our Universe as free particles ("free" superbradyons), in which case we expect them to be weakly coupled to standard matter. If a preonic vacuum is actually leading the basic dynamics of Particle Physics and Cosmology, and standard particles are vacuum excitations, the Gödel-Cohen incompleteness will apply to vacuum dynamics whereas the conventional laws of physics will actually be approximate and have error bars. We discuss here the possible role of the superbradyonic vacuum and of the SST in generating Quantum Mechanics, as well as the implications of such a dynamical origin of the conventional laws of Physics and possible evidences in experiments and observations. Black holes, gravitational waves, possible "free" superbradyons or preonic waves, unconventional vacuum radiation… are considered from this point of view paying particular attention to LIGO, VIRGO and CERN experiments. This lecture is dedicated to the memory of John Bell

The Association Between Risk-taking Behavior and Helmet Use Among Motorcyclist

NASA Astrophysics Data System (ADS)

Trinh, Tu Anh; Phuong Linh Le, Thi

2018-04-01

The central aim of the research was to examine speeding behavior without helmet wearing among motorcycle riders in Ho Chi Minh City. The research model expanded the Theory of Planned Behavior by both psychological flow theory and sensation-seeking. 268 motorcyclists were involved in the research. A Confirmatory factor analysis and a Structural equation modeling were employed for model specification. The findings indicated a significant effect between predictors and the intention of speeding without helmet wearing. In addition, there was direct relation between intention and actual behavior. Also, sensation-seeking proved to be important in moderating predictors between the low-sensation-seeking motorcyclists and high-sensation-seeking ones. A deeper understanding of why motorcycle riders exceed the speed limit without wearing helmet played key role in changing their behavior.

Improved Cognition While Cycling in Parkinson’s Disease Patients and Healthy Adults

PubMed Central

Hazamy, Audrey A.; Altmann, Lori J. P.; Stegemöller, Elizabeth; Bowers, Dawn; Lee, Hyo Keun; Wilson, Jonathan; Okun, Michael S.; Hass, Chris J.

2017-01-01

Persons with Parkinson’s disease (PD) are typically more susceptible than healthy adults to impaired performance when two tasks (dual task interference) are performed simultaneously. This limitation has by many experts been attributed to limitations in cognitive resources. Nearly all studies of dual task performance in PD employ walking or balance-based motor tasks, which are commonly impaired in PD. These tasks can be performed using a combination of one or two executive function tasks. The current study examined whether persons with PD would demonstrate greater dual task effects on cognition compared to healthy older adults (HOAs) during a concurrent cycling task. Participants with and without PD completed a battery of 12 cognitive tasks assessing visual and verbal processing in the following cognitive domains: speed of processing, controlled processing, working memory and executive function. Persons with PD exhibited impairments compared to healthy participants in select tasks (i.e., 0-Back, 2-Back and operation span). Further, both groups unexpectedly exhibited dual task facilitation of response times in visual tasks across cognitive domains, and improved verbal recall during an executive function task. Only one measure, 2-back, showed a speed-accuracy trade-off in the dual task. These results demonstrate that, when paired with a motor task in which they are not impaired, people with PD exhibit similar dual task effects on cognitive tasks as HOAs, even when these dual task effects are facilitative. More generally, these findings demonstrate that pairing cognitive tasks with cycling may actually improve cognitive performance which may have therapeutic relevance to cognitive decline associated with aging and PD pathology. PMID:28088064

Speed Isn't Everything: Complex Processing Speed Measures Mask Individual Differences and Developmental Changes in Executive Control

ERIC Educational Resources Information Center

Cepeda, Nicholas J.; Blackwell, Katharine A.; Munakata, Yuko

2013-01-01

The rate at which people process information appears to influence many aspects of cognition across the lifespan. However, many commonly accepted measures of "processing speed" may require goal maintenance, manipulation of information in working memory, and decision-making, blurring the distinction between processing speed and executive…

SR high-speed K-edge subtraction angiography in the small animal (abstract)

NASA Astrophysics Data System (ADS)

Takeda, T.; Akisada, M.; Nakajima, T.; Anno, I.; Ueda, K.; Umetani, K.; Yamaguchi, C.

1989-07-01

To assess the ability of the high-speed K-edge energy subtraction system which was made at beamline 8C of Photon Factory, Tsukuba, we performed an animal experiment. Rabbits were used for the intravenous K-edge subtraction angiography. In this paper, the actual images of the artery obtained by this system, are demonstrated. The high-speed K-edge subtraction system consisted of movable silicon (111) monocrystals, II-ITV, and digital memory system. Image processing was performed by 68000-IP computer. The monochromatic x-ray beam size was 50×60 mm. Photon energy above and below iodine K edge was changed within 16 ms and 32 frames of images were obtained sequentially. The rabbits were anaesthetized by phenobarbital and a 5F catheter was inserted into inferior vena cava via the femoral vein. 1.5 ml/kg of contrast material (Conlaxin H) was injected at the rate of 0.5 ml/kg/s. TV images were obtained 3 s after the starting point of injection. By using this system, the clear K-edge subtracted images were obtained sequentially as a conventional DSA system. The quality of the images were better than that obtained by DSA. The dynamical blood flow was analyzed, and the best arterial image could be selected from the sequential images. The structures of aortic arch, common carotid arteries, right subclavian artery, and internal thoracic artery were obtained at the chest. Both common carotid arteries and vertebral arteries were recorded at the neck. The diameter of about 0.3-0.4 mm artery could be clearly revealed. The high-speed K-edge subtraction system demonstrates the very sharp arterial images clearly and dynamically.

Working memory span and motor and cognitive speed in schizophrenia.

PubMed

Brébion, Gildas; David, Anthony S; Jones, Hugh M; Pilowsky, Lyn S

2009-06-01

The aim of this study was to investigate the verbal working memory deficit and decrease of motor and cognitive speed in patients with schizophrenia, and to clarify their associations with negative and depressive symptomatology. Forty patients with schizophrenia and 41 healthy control individuals were administered the backward digit span to assess the working memory capacity, along with 3 tests of processing speed. Patients demonstrated reduced backward digit span, as well as decreased motor and cognitive speed. Regression analyses indicated that the backward digit span was associated with cognitive speed. It was not associated with either negative or depressive symptoms. Decreased processing speed was unrelated to negative symptoms, but the depression score was significantly associated with the cognitive speed measure. Working memory and processing speed seem to share a cognitive component. Depression, but not negative symptoms, affects processing speed, especially by decreasing cognitive speed.

Who is talking in backward crosstalk? Disentangling response- from goal-conflict in dual-task performance.

PubMed

Janczyk, Markus; Pfister, Roland; Hommel, Bernhard; Kunde, Wilfried

2014-07-01

Responses in the second of two subsequently performed tasks can speed up compatible responses in the temporally preceding first task. Such backward crosstalk effects (BCEs) represent a challenge to the assumption of serial processing in stage models of human information processing, because they indicate that certain features of the second response have to be represented before the first response is emitted. Which of these features are actually relevant for BCEs is an open question, even though identifying these features is important for understanding the nature of parallel and serial response selection processes in dual-task performance. Motivated by effect-based models of action control, we show in three experiments that the BCE to a considerable degree reflects features of intended action effects, although features of the response proper (or response-associated kinesthetic feedback) also seem to play a role. These findings suggest that the codes of action effects (or action goals) can become activated simultaneously rather than serially, thereby creating BCEs. Copyright © 2014 Elsevier B.V. All rights reserved.

Frequency-encoded photonic qubits for scalable quantum information processing

DOE PAGES

Lukens, Joseph M.; Lougovski, Pavel

2016-12-21

Among the objectives for large-scale quantum computation is the quantum interconnect: a device that uses photons to interface qubits that otherwise could not interact. However, the current approaches require photons indistinguishable in frequency—a major challenge for systems experiencing different local environments or of different physical compositions altogether. Here, we develop an entirely new platform that actually exploits such frequency mismatch for processing quantum information. Labeled “spectral linear optical quantum computation” (spectral LOQC), our protocol offers favorable linear scaling of optical resources and enjoys an unprecedented degree of parallelism, as an arbitrary Ν-qubit quantum gate may be performed in parallel onmore » multiple Ν-qubit sets in the same linear optical device. Here, not only does spectral LOQC offer new potential for optical interconnects, but it also brings the ubiquitous technology of high-speed fiber optics to bear on photonic quantum information, making wavelength-configurable and robust optical quantum systems within reach.« less

Frequency-encoded photonic qubits for scalable quantum information processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lukens, Joseph M.; Lougovski, Pavel

Among the objectives for large-scale quantum computation is the quantum interconnect: a device that uses photons to interface qubits that otherwise could not interact. However, the current approaches require photons indistinguishable in frequency—a major challenge for systems experiencing different local environments or of different physical compositions altogether. Here, we develop an entirely new platform that actually exploits such frequency mismatch for processing quantum information. Labeled “spectral linear optical quantum computation” (spectral LOQC), our protocol offers favorable linear scaling of optical resources and enjoys an unprecedented degree of parallelism, as an arbitrary Ν-qubit quantum gate may be performed in parallel onmore » multiple Ν-qubit sets in the same linear optical device. Here, not only does spectral LOQC offer new potential for optical interconnects, but it also brings the ubiquitous technology of high-speed fiber optics to bear on photonic quantum information, making wavelength-configurable and robust optical quantum systems within reach.« less

Psychosocial Risks Generated By Assets Specific Design Software

NASA Astrophysics Data System (ADS)

Remus, Furtună; Angela, Domnariu; Petru, Lazăr

2015-07-01

The human activity concerning an occupation is resultant from the interaction between the psycho-biological, socio-cultural and organizational-occupational factors. Tehnological development, automation and computerization that are to be found in all the branches of activity, the level of speed in which things develop, as well as reaching their complexity, require less and less physical aptitudes and more cognitive qualifications. The person included in the work process is bound in most of the cases to come in line with the organizational-occupational situations that are specific to the demands of the job. The role of the programmer is essencial in the process of execution of ordered softwares, thus the truly brilliant ideas can only come from well-rested minds, concentrated on their tasks. The actual requirements of the jobs, besides the high number of benefits and opportunities, also create a series of psycho-social risks, which can increase the level of stress during work activity, especially for those who work under pressure.

An Iterative Closest Points Algorithm for Registration of 3D Laser Scanner Point Clouds with Geometric Features.

PubMed

He, Ying; Liang, Bin; Yang, Jun; Li, Shunzhi; He, Jin

2017-08-11

The Iterative Closest Points (ICP) algorithm is the mainstream algorithm used in the process of accurate registration of 3D point cloud data. The algorithm requires a proper initial value and the approximate registration of two point clouds to prevent the algorithm from falling into local extremes, but in the actual point cloud matching process, it is difficult to ensure compliance with this requirement. In this paper, we proposed the ICP algorithm based on point cloud features (GF-ICP). This method uses the geometrical features of the point cloud to be registered, such as curvature, surface normal and point cloud density, to search for the correspondence relationships between two point clouds and introduces the geometric features into the error function to realize the accurate registration of two point clouds. The experimental results showed that the algorithm can improve the convergence speed and the interval of convergence without setting a proper initial value.

An Iterative Closest Points Algorithm for Registration of 3D Laser Scanner Point Clouds with Geometric Features

PubMed Central

Liang, Bin; Yang, Jun; Li, Shunzhi; He, Jin

2017-01-01

The Iterative Closest Points (ICP) algorithm is the mainstream algorithm used in the process of accurate registration of 3D point cloud data. The algorithm requires a proper initial value and the approximate registration of two point clouds to prevent the algorithm from falling into local extremes, but in the actual point cloud matching process, it is difficult to ensure compliance with this requirement. In this paper, we proposed the ICP algorithm based on point cloud features (GF-ICP). This method uses the geometrical features of the point cloud to be registered, such as curvature, surface normal and point cloud density, to search for the correspondence relationships between two point clouds and introduces the geometric features into the error function to realize the accurate registration of two point clouds. The experimental results showed that the algorithm can improve the convergence speed and the interval of convergence without setting a proper initial value. PMID:28800096

Effort Not Speed Characterizes Comprehension of Spoken Sentences by Older Adults with Mild Hearing Impairment

PubMed Central

Ayasse, Nicole D.; Lash, Amanda; Wingfield, Arthur

2017-01-01

In spite of the rapidity of everyday speech, older adults tend to keep up relatively well in day-to-day listening. In laboratory settings older adults do not respond as quickly as younger adults in off-line tests of sentence comprehension, but the question is whether comprehension itself is actually slower. Two unique features of the human eye were used to address this question. First, we tracked eye-movements as 20 young adults and 20 healthy older adults listened to sentences that referred to one of four objects pictured on a computer screen. Although the older adults took longer to indicate the referenced object with a cursor-pointing response, their gaze moved to the correct object as rapidly as that of the younger adults. Second, we concurrently measured dilation of the pupil of the eye as a physiological index of effort. This measure revealed that although poorer hearing acuity did not slow processing, success came at the cost of greater processing effort. PMID:28119598

Effort Not Speed Characterizes Comprehension of Spoken Sentences by Older Adults with Mild Hearing Impairment.

PubMed

Ayasse, Nicole D; Lash, Amanda; Wingfield, Arthur

2016-01-01

In spite of the rapidity of everyday speech, older adults tend to keep up relatively well in day-to-day listening. In laboratory settings older adults do not respond as quickly as younger adults in off-line tests of sentence comprehension, but the question is whether comprehension itself is actually slower. Two unique features of the human eye were used to address this question. First, we tracked eye-movements as 20 young adults and 20 healthy older adults listened to sentences that referred to one of four objects pictured on a computer screen. Although the older adults took longer to indicate the referenced object with a cursor-pointing response, their gaze moved to the correct object as rapidly as that of the younger adults. Second, we concurrently measured dilation of the pupil of the eye as a physiological index of effort. This measure revealed that although poorer hearing acuity did not slow processing, success came at the cost of greater processing effort.

Influence of neuromuscular noise and walking speed on fall risk and dynamic stability in a 3D dynamic walking model.

PubMed

Roos, Paulien E; Dingwell, Jonathan B

2013-06-21

Older adults and those with increased fall risk tend to walk slower. They may do this voluntarily to reduce their fall risk. However, both slower and faster walking speeds can predict increased risk of different types of falls. The mechanisms that contribute to fall risk across speeds are not well known. Faster walking requires greater forward propulsion, generated by larger muscle forces. However, greater muscle activation induces increased signal-dependent neuromuscular noise. These speed-related increases in neuromuscular noise may contribute to the increased fall risk observed at faster walking speeds. Using a 3D dynamic walking model, we systematically varied walking speed without and with physiologically-appropriate neuromuscular noise. We quantified how actual fall risk changed with gait speed, how neuromuscular noise affected speed-related changes in fall risk, and how well orbital and local dynamic stability measures predicted changes in fall risk across speeds. When we included physiologically-appropriate noise to the 'push-off' force in our model, fall risk increased with increasing walking speed. Changes in kinematic variability, orbital, and local dynamic stability did not predict these speed-related changes in fall risk. Thus, the increased neuromuscular variability that results from increased signal-dependent noise that is necessitated by the greater muscular force requirements of faster walking may contribute to the increased fall risk observed at faster walking speeds. The lower fall risk observed at slower speeds supports experimental evidence that slowing down can be an effective strategy to reduce fall risk. This may help explain the slower walking speeds observed in older adults and others. Copyright © 2013 Elsevier Ltd. All rights reserved.

Influence of Neuromuscular Noise and Walking Speed on Fall Risk and Dynamic Stability in a 3D Dynamic Walking Model

PubMed Central

Roos, Paulien E.; Dingwell, Jonathan B.

2013-01-01

Older adults and those with increased fall risk tend to walk slower. They may do this voluntarily to reduce their fall risk. However, both slower and faster walking speeds can predict increased risk of different types of falls. The mechanisms that contribute to fall risk across speeds are not well known. Faster walking requires greater forward propulsion, generated by larger muscle forces. However, greater muscle activation induces increased signal-dependent neuromuscular noise. These speed-related increases in neuromuscular noise may contribute to the increased fall risk observed at faster walking speeds. Using a 3D dynamic walking model, we systematically varied walking speed without and with physiologically-appropriate neuromuscular noise. We quantified how actual fall risk changed with gait speed, how neuromuscular noise affected speed-related changes in fall risk, and how well orbital and local dynamic stability measures predicted changes in fall risk across speeds. When we included physiologically-appropriate noise to the ‘push-off’ force in our model, fall risk increased with increasing walking speed. Changes in kinematic variability, orbital, and local dynamic stability did not predict these speed-related changes in fall risk. Thus, the increased neuromuscular variability that results from increased signal-dependent noise that is necessitated by the greater muscular force requirements of faster walking may contribute to the increased fall risk observed at faster walking speeds. The lower fall risk observed at slower speeds supports experimental evidence that slowing down can be an effective strategy to reduce fall risk. This may help explain the slower walking speeds observed in older adults and others. PMID:23659911

Large-Scale Advanced Prop-Fan (LAP) pitch change actuator and control design report

NASA Technical Reports Server (NTRS)

Schwartz, R. A.; Carvalho, P.; Cutler, M. J.

1986-01-01

In recent years, considerable attention has been directed toward improving aircraft fuel consumption. Studies have shown that the high inherent efficiency previously demonstrated by low speed turboprop propulsion systems may now be extended to today's higher speed aircraft if advanced high-speed propeller blades having thin airfoils and aerodynamic sweep are utilized. Hamilton Standard has designed a 9-foot diameter single-rotation Large-Scale Advanced Prop-Fan (LAP) which will be tested on a static test stand, in a high speed wind tunnel and on a research aircraft. The major objective of this testing is to establish the structural integrity of large-scale Prop-Fans of advanced construction in addition to the evaluation of aerodynamic performance and aeroacoustic design. This report describes the operation, design features and actual hardware of the (LAP) Prop-Fan pitch control system. The pitch control system which controls blade angle and propeller speed consists of two separate assemblies. The first is the control unit which provides the hydraulic supply, speed governing and feather function for the system. The second unit is the hydro-mechanical pitch change actuator which directly changes blade angle (pitch) as scheduled by the control.

Gender Differences in Processing Speed: A Review of Recent Research

ERIC Educational Resources Information Center

Roivainen, Eka

2011-01-01

A review of recent large-scale studies on gender differences in processing speed and on the cognitive factors assumed to affect processing speed was performed. It was found that females have an advantage in processing speed tasks involving digits and alphabets as well as in rapid naming tasks while males are faster on reaction time tests and…

Quantification of the heat exchange of chicken eggs.

PubMed

Van Brecht, A; Hens, H; Lemaire, J L; Aerts, J M; Degraeve, P; Berckmans, D

2005-03-01

In the incubation process of domestic avian eggs, the development of the embryo is mainly influenced by the physical microenvironment around the egg. Only small spatiotemporal deviations in the optimal incubator air temperature are allowed to optimize hatchability and hatchling quality. The temperature of the embryo depends on 3 factors: (1) the air temperature, (2) the exchange of heat between the egg and its microenvironment and (3) the time-variable heat production of the embryo. Theoretical estimates on the heat exchange between an egg and its physical microenvironment are approximated using equations that assume an approximate spherical shape for eggs. The objective of this research was to determine the heat transfer between the eggshell and its microenvironment and then compare this value to various theoretical estimates. By using experimental data, the overall and the convective heat transfer coefficients were determined as a function of heat production, air humidity, air speed, and air temperature. Heat transfer was not affected by air humidity but solely by air temperature, embryonic heat generation, and air speed and flow around eggs. Also, heat transfer in forced-air incubators occurs mainly by convective heat loss, which is dependent on the speed of airflow. A vertical airflow is more efficient than a horizontal airflow in transferring heat from the egg. We showed that describing an egg as a sphere underestimated convective heat transfer by 33% and was, therefore, too simplistic to accurately assess actual heat transfer from real eggs.

Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

NASA Technical Reports Server (NTRS)

Fleming, David P.; Poplawski, J. V.

2003-01-01

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

Bow Shocks in Space

NASA Image and Video Library

2016-01-05

Bow shocks thought to mark the paths of massive, speeding stars are highlighted in these images from NASA's Spitzer Space Telescope and Wide-field Infrared Survey Explorer, or WISE. Cosmic bow shocks occur when massive stars zip through space, pushing material ahead of them in the same way that water piles up in front of a race boat. The stars also produce high-speed winds that smack into this compressed material. The end result is pile-up of heated material that glows in infrared light. In these images, infrared light has been assigned the colored red. Green shows wispy dust in the region and blue shows stars. The two images at left are from Spitzer, and the one on the right is from WISE. The speeding stars thought to be creating the bow shocks can be seen at the center of each arc-shaped feature. The image at right actually consists of two bow shocks and two speeding stars. All the speeding stars are massive, ranging from about 8 to 30 times the mass of our sun. http://photojournal.jpl.nasa.gov/catalog/PIA20062

Tailoring in risk communication by linking risk profiles and communication preferences: The case of speeding of young car drivers.

PubMed

Geber, Sarah; Baumann, Eva; Klimmt, Christoph

2016-12-01

Speeding is one of the most relevant risk behaviors for serious and fatal accidents, particularly among young drivers. This study presents a tailoring strategy for anti-speeding communication. By referring to their motivational dispositions toward speeding derived from motivational models of health behavior, young car drivers were segmented into different risk groups. In order to ensure that risk communication efforts would actually be capable to target these groups, the linkage between the risk profiles and communication preferences were explored. The study was conducted on the basis of survey data of 1168 German car drivers aged between 17 and 24 years. The data reveal four types of risk drivers significantly differing in their motivational profiles. Moreover, the findings show significant differences in communication habits and media use between these risk groups. By linking the risk profiles and communication preferences, implications for tailoring strategies of road safety communication campaigns are derived. Promising segmentation and targeting strategies are discussed also beyond the current case of anti-speeding campaigns. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ice and AIS: ship speed data and sea ice forecasts in the Baltic Sea

NASA Astrophysics Data System (ADS)

Löptien, U.; Axell, L.

2014-12-01

The Baltic Sea is a seasonally ice-covered marginal sea located in a densely populated area in northern Europe. Severe sea ice conditions have the potential to hinder the intense ship traffic considerably. Thus, sea ice fore- and nowcasts are regularly provided by the national weather services. Typically, the forecast comprises several ice properties that are distributed as prognostic variables, but their actual usefulness is difficult to measure, and the ship captains must determine their relative importance and relevance for optimal ship speed and safety ad hoc. The present study provides a more objective approach by comparing the ship speeds, obtained by the automatic identification system (AIS), with the respective forecasted ice conditions. We find that, despite an unavoidable random component, this information is useful to constrain and rate fore- and nowcasts. More precisely, 62-67% of ship speed variations can be explained by the forecasted ice properties when fitting a mixed-effect model. This statistical fit is based on a test region in the Bothnian Sea during the severe winter 2011 and employs 15 to 25 min averages of ship speed.

Ice and AIS: ship speed data and sea ice forecasts in the Baltic Sea

NASA Astrophysics Data System (ADS)

Löptien, U.; Axell, L.

2014-07-01

The Baltic Sea is a seasonally ice covered marginal sea located in a densely populated area in northern Europe. Severe sea ice conditions have the potential to hinder the intense ship traffic considerably. Thus, sea ice fore- and nowcasts are regularly provided by the national weather services. Typically, several ice properties are allocated, but their actual usefulness is difficult to measure and the ship captains must determine their relative importance and relevance for optimal ship speed and safety ad hoc. The present study provides a more objective approach by comparing the ship speeds, obtained by the Automatic Identification System (AIS), with the respective forecasted ice conditions. We find that, despite an unavoidable random component, this information is useful to constrain and rate fore- and nowcasts. More precisely, 62-67% of ship speed variations can be explained by the forecasted ice properties when fitting a mixed effect model. This statistical fit is based on a test region in the Bothnian Bay during the severe winter 2011 and employes 15 to 25 min averages of ship speed.

Road user behaviour changes following a self-explaining roads intervention.

PubMed

Mackie, Hamish W; Charlton, Samuel G; Baas, Peter H; Villasenor, Pablo C

2013-01-01

The self-explaining roads (SER) approach uses road designs that evoke correct expectations and driving behaviours from road users to create a safe and user-friendly road network. Following the implementation of an SER process and retrofitting of local and collector roads in a suburb within Auckland City, lower speeds on local roads and less variation in speed on both local and collector roads were achieved, along with a closer match between actual and perceived safe speeds. Preliminary analyses of crash data shows that the project has resulted in a 30% reduction crash numbers and an 86% reduction in crash costs per annum, since the road changes were completed. In order to further understand the outcomes from this project, a study was carried out to measure the effects of the SER intervention on the activity and behaviour of all road users. Video was collected over nine separate days, at nine different locations, both before and after SER construction. Road user behaviour categories were developed for all potential road users at different location types and then used to code the video data. Following SER construction, on local roads there was a relatively higher proportion of pedestrians, less uniformity in vehicle lane keeping and less indicating by motorists along with less through traffic, reflecting a more informal/low speed local road environment. Pedestrians were less constrained on local roads following SER construction, possibly reflecting a perceptually safer and more user-friendly environment. These behaviours were not generally evident on collector roads, a trend also shown by the previous study of speed changes. Given that one of the objectives of SER is to match road user behaviour with functionally different road categories, the road user behaviour differences demonstrated on different road types within the SER trial area provides further reinforcement of a successful SER trial. Copyright © 2012 Elsevier Ltd. All rights reserved.

The prediction of speed and incline in outdoor running in humans using accelerometry.

PubMed

Herren, R; Sparti, A; Aminian, K; Schutz, Y

1999-07-01

To explore whether triaxial accelerometric measurements can be utilized to accurately assess speed and incline of running in free-living conditions. Body accelerations during running were recorded at the lower back and at the heel by a portable data logger in 20 human subjects, 10 men, and 10 women. After parameterizing body accelerations, two neural networks were designed to recognize each running pattern and calculate speed and incline. Each subject ran 18 times on outdoor roads at various speeds and inclines; 12 runs were used to calibrate the neural networks whereas the 6 other runs were used to validate the model. A small difference between the estimated and the actual values was observed: the square root of the mean square error (RMSE) was 0.12 m x s(-1) for speed and 0.014 radiant (rad) (or 1.4% in absolute value) for incline. Multiple regression analysis allowed accurate prediction of speed (RMSE = 0.14 m x s(-1)) but not of incline (RMSE = 0.026 rad or 2.6% slope). Triaxial accelerometric measurements allows an accurate estimation of speed of running and incline of terrain (the latter with more uncertainty). This will permit the validation of the energetic results generated on the treadmill as applied to more physiological unconstrained running conditions.

Text Characteristics of Task Input and Difficulty in Second Language Listening Comprehension

ERIC Educational Resources Information Center

Revesz, Andrea; Brunfaut, Tineke

2013-01-01

This study investigated the effects of a group of task factors on advanced English as a second language learners' actual and perceived listening performance. We examined whether the speed, linguistic complexity, and explicitness of the listening text along with characteristics of the text necessary for task completion influenced comprehension. We…

Brain-Based Teaching in the Digital Age

ERIC Educational Resources Information Center

Sprenger, Marilee

2010-01-01

In the digital age, your students have the ways, means, and speed to gather any information they want. But they need your guidance more than ever. Discover how digital technology is actually changing your students' brains. Learn why this creates new obstacles for teachers, but also opens up potential new pathways for learning. You will understand…

NASA Langley's Aircraft Landing Dynamics Facility

NASA Technical Reports Server (NTRS)

Davis, Pamela A.

1993-01-01

The Aircraft Landing Dynamics Facility (ALDF) is a unique facility with the ability to test aircraft landing gear systems on actual runway surfaces at operational ground speeds and loading conditions. A brief historical overview of the original Landing Loads Track (LLT) is given, followed by a detailed description of the new ALDF systems and operational capabilities.

Possibility Of Generating Significant Storm Surge On The Western Seaboard Of Metro Manila, Philippines

NASA Astrophysics Data System (ADS)

Suarez, J. K. B.; Santiago, J. T.; Tablazon, J. P.; Dasallas, L. L.; Goting, P. G.; Lagmay, A. M. A.

2016-12-01

The Philippines, located in the Northwestern Pacific Typhoon gateway to Asia, is considered one of the most susceptible to tropical cyclone related hazards. One of the most disastrous effects of tropical cyclones is storm surge. With Metro Manila being a coastal area and the most populous region in the country, with approximately 12.8 million people residing in it, it is of great interest to determine the possibility of generating significant level of storm surge in the country's capital. The necessity to determine the storm surge susceptibility was brought upon by the effect of Typhoon Haiyan on eastern Visayas in 2013, where more than 6,000 people died and resulted to about 2.86 billion dollars' worth of damages. To achieve the objectives, the actual tracks and wind speed of historical typhoon (JMA data since 1951) was mapped for the Philippines. The simulated wind speed map shows that the maximum winds are mostly experienced on the eastern side of the country; with a considerable decrease in wind intensity as the typhoon reaches the western seaboard due to land surface. The Haiyan-strength wind speed is then applied to the actual historical typhoon tracks to determine the hypothetical values of wind speed as a typhoon with Haiyan intensity reached Metro Manila. Results show that, if a typhoon with a Haiyan-like intensity is to traverse tracks like those of Rita 1978, Collen 1992, Sybil 1995, Bebinca 2000 and Xangsane 2000, there is a huge possibility of generating storm surge height of 3.9 to 5.6 m in the western seaboard of Metro Manila, even after considering the diminishing effect of surface friction.

Lightning Instrumentation at KSC

NASA Technical Reports Server (NTRS)

Colon, Jose L.; Eng, D.

2003-01-01

This report summarizes lightning phenomena with a brief explanation of lightning generation and lightning activity as related to KSC. An analysis of the instrumentation used at launching Pads 39 A&B for measurements of lightning effects is included with alternatives and recommendations to improve the protection system and upgrade the actual instrumentation system. An architecture for a new data collection system to replace the present one is also included. A novel architecture to obtain lightning current information from several sensors using only one high speed recording channel while monitoring all sensors to replace the actual manual lightning current recorders and a novel device for the protection system are described.

Toolpath Strategy and Optimum Combination of Machining Parameter during Pocket Mill Process of Plastic Mold Steels Material

NASA Astrophysics Data System (ADS)

Wibowo, Y. T.; Baskoro, S. Y.; Manurung, V. A. T.

2018-02-01

Plastic based products spread all over the world in many aspects of life. The ability to substitute other materials is getting stronger and wider. The use of plastic materials increases and become unavoidable. Plastic based mass production requires injection process as well Mold. The milling process of plastic mold steel material was done using HSS End Mill cutting tool that is widely used in a small and medium enterprise for the reason of its ability to be re sharpened and relatively inexpensive. Study on the effect of the geometry tool states that it has an important effect on the quality improvement. Cutting speed, feed rate, depth of cut and radii are input parameters beside to the tool path strategy. This paper aims to investigate input parameter and cutting tools behaviors within some different tool path strategy. For the reason of experiments efficiency Taguchi method and ANOVA were used. Response studied is surface roughness and cutting behaviors. By achieving the expected quality, no more additional process is required. Finally, the optimal combination of machining parameters will deliver the expected roughness and of course totally reduced cutting time. However actually, SMEs do not optimally use this data for cost reduction.

Brain white matter structure and information processing speed in healthy older age.

PubMed

Kuznetsova, Ksenia A; Maniega, Susana Muñoz; Ritchie, Stuart J; Cox, Simon R; Storkey, Amos J; Starr, John M; Wardlaw, Joanna M; Deary, Ian J; Bastin, Mark E

2016-07-01

Cognitive decline, especially the slowing of information processing speed, is associated with normal ageing. This decline may be due to brain cortico-cortical disconnection caused by age-related white matter deterioration. We present results from a large, narrow age range cohort of generally healthy, community-dwelling subjects in their seventies who also had their cognitive ability tested in youth (age 11 years). We investigate associations between older age brain white matter structure, several measures of information processing speed and childhood cognitive ability in 581 subjects. Analysis of diffusion tensor MRI data using Tract-based Spatial Statistics (TBSS) showed that all measures of information processing speed, as well as a general speed factor composed from these tests (g speed), were significantly associated with fractional anisotropy (FA) across the white matter skeleton rather than in specific tracts. Cognitive ability measured at age 11 years was not associated with older age white matter FA, except for the g speed-independent components of several individual processing speed tests. These results indicate that quicker and more efficient information processing requires global connectivity in older age, and that associations between white matter FA and information processing speed (both individual test scores and g speed), unlike some other aspects of later life brain structure, are generally not accounted for by cognitive ability measured in youth.

Feasible Application Area Study for Linear Laser Cutting in Paper Making Processes

NASA Astrophysics Data System (ADS)

Happonen, A.; Stepanov, A.; Piili, H.

Traditional industry sectors, like paper making industry, tend to stay within well-known technology rather than going forward towards promising, but still quite new technical solutions and applications. This study analyses the feasibility of the laser cutting in large-scale industrial paper making processes. Aim was to reveal development and process related challenges and improvement potential in paper making processes by utilizing laser technology. This study has been carried out, because there still seems to be only few large-scale industrial laser processing applications in paper converting processes worldwide, even in the beginning of 2010's. Because of this, the small-scale use of lasers in paper material manufacturing industry is related to a shortage of well-known and widely available published research articles and published measurement data (e.g. actual achieved cut speeds with high quality cut edges, set-up times and so on). It was concluded that laser cutting has strong potential in industrial applications for paper making industries. This potential includes quality improvements and a competitive advantage for paper machine manufacturers and industry. The innovations have also added potential, when developing new paper products. An example of these kinds of products are ones with printed intelligence, which could be a new business opportunity for the paper industries all around the world.

Foot strike patterns of runners at the 15-km point during an elite-level half marathon.

PubMed

Hasegawa, Hiroshi; Yamauchi, Takeshi; Kraemer, William J

2007-08-01

There are various recommendations by many coaches regarding foot landing techniques in distance running that are meant to improve running performance and prevent injuries. Several studies have investigated the kinematic and kinetic differences between rearfoot strike (RFS), midfoot strike (MFS), and forefoot strike (FFS) patterns at foot landing and their effects on running efficiency on a treadmill and over ground conditions. However, little is known about the actual condition of the foot strike pattern during an actual road race at the elite level of competition. The purpose of the present study was to document actual foot strike patterns during a half marathon in which elite international level runners, including Olympians, compete. Four hundred fifteen runners were filmed by 2 120-Hz video cameras in the height of 0.15 m placed at the 15.0-km point and obtained sagittal foot landing and taking off images for 283 runners. Rearfoot strike was observed in 74.9% of all analyzed runners, MFS in 23.7%, and FFS in 1.4%. The percentage of MFS was higher in the faster runners group, when all runners were ranked and divided into 50 runner groups at the 15.0-km point of the competition. In the top 50, which included up to the 69th place runner in actual order who passed the 15-km point at 45 minutes, 53 second (this speed represents 5.45 m x s(-1), or 15 minutes, 17 seconds per 5 km), RFS, MFS, and FFS were 62.0, 36.0, and 2.0%, respectively. Contact time (CT) clearly increased for the slower runners, or the placement order increased (r = 0.71, p < or = 0.05). The CT for RFS + FFS for every 50 runners group significantly increased with increase of the placement order. The CT for RFS was significantly longer than MFS + FFS (200.0 +/- 21.3 vs. 183.0 +/- 16 millisecond). Apparent inversion (INV) of the foot at the foot strike was observed in 42% of all runners. The percentage of INV for MFS was higher than for RFS and FFS (62.5, 32.0, and 50%, respectively). The CT with INV for MFS + FFS was significantly shorter than the CT with and without INV for RFS. Furthermore, the CT with INV was significantly shorter than push-off time without INV for RFS. The findings of this study indicate that foot strike patterns are related to running speed. The percentage of RFS increases with the decreasing of the running speed; conversely, the percentage of MFS increases as the running speed increases. A shorter contact time and a higher frequency of inversion at the foot contact might contribute to higher running economy.

The Involvement of Speed-of-Processing in Story Listening in Preschool Children: A Functional and Structural Connectivity Study.

PubMed

Horowitz-Kraus, Tzipi; Farah, Rola; DiFrancesco, Mark; Vannest, Jennifer

2017-02-01

Story listening in children relies on brain regions supporting speech perception, auditory word recognition, syntax, semantics, and discourse abilities, along with the ability to attend and process information (part of executive functions). Speed-of-processing is an early-developed executive function. We used functional and structural magnetic resonance imaging (MRI) to demonstrate the relationship between story listening and speed-of-processing in preschool-age children. Eighteen participants performed story-listening tasks during MRI scans. Functional and structural connectivity analysis was performed using the speed-of-processing scores as regressors. Activation in the superior frontal gyrus during story listening positively correlated with speed-of-processing scores. This region was functionally connected with the superior temporal gyrus, insula, and hippocampus. Fractional anisotropy in the inferior frontooccipital fasciculus, which connects the superior frontal and temporal gyri, was positively correlated with speed-of-processing scores. Our results suggest that speed-of-processing skills in preschool-age children are reflected in functional activation and connectivity during story listening and may act as a biomarker for future academic abilities. Georg Thieme Verlag KG Stuttgart · New York.

Global Processing Speed in Children With Low Reading Ability and in Children and Adults With Typical Reading Ability: Exploratory Factor Analytic Models

PubMed Central

Peter, Beate; Matsushita, Mark; Raskind, Wendy H.

2013-01-01

Purpose To investigate processing speed as a latent dimension in children with dyslexia and children and adults with typical reading skills. Method Exploratory factor analysis (FA) was based on a sample of multigenerational families, each ascertained through a child with dyslexia. Eleven measures—6 of them timed—represented verbal and nonverbal processes, alphabet writing, and motor sequencing in the hand and oral motor system. FA was conducted in 4 cohorts (all children, a subset of children with low reading scores, a subset of children with typical reading scores, and adults with typical reading scores; total N = 829). Results Processing speed formed the first factor in all cohorts. Both measures of motor sequencing speed loaded on the speed factor with the other timed variables. Children with poor reading scores showed lower speed factor scores than did typical peers. The speed factor was negatively correlated with age in the adults. Conclusions The speed dimension was observed independently of participant cohort, gender, and reading ability. Results are consistent with a unified theory of processing speed as a quadratic function of age in typical development and with slowed processing in poor readers. PMID:21081672

Transduction in Drosophila olfactory receptor neurons is invariant to air speed

PubMed Central

Zhou, Yi

2012-01-01

In the vertebrate nose, increasing air speed tends to increase the magnitude of odor-evoked activity in olfactory receptor neurons (ORNs), given constant odor concentration and duration. It is often assumed that the same is true of insect olfactory organs, but this has not been directly tested. In this study, we examined the effect of air speed on ORN responses in Drosophila melanogaster. We constructed an odor delivery device that allowed us to independently vary concentration and air speed, and we used a fast photoionization detector to precisely measure the actual odor concentration at the antenna while simultaneously recording spikes from ORNs in vivo. Our results demonstrate that Drosophila ORN odor responses are invariant to air speed, as long as odor concentration is kept constant. This finding was true across a >100-fold range of air speeds. Because odor hydrophobicity has been proposed to affect the air speed dependence of olfactory transduction, we tested a >1,000-fold range of hydrophobicity values and found that ORN responses are invariant to air speed across this full range. These results have implications for the mechanisms of odor delivery to Drosophila ORNs. Our findings are also significant because flies have a limited ability to control air flow across their antennae, unlike terrestrial vertebrates, which can control air flow within their nasal cavity. Thus, for the fly, invariance to air speed may be adaptive because it confers robustness to changing wind conditions. PMID:22815404

Rapid Automatized Naming in Children with Dyslexia: Is Inhibitory Control Involved?

PubMed

Bexkens, Anika; van den Wildenberg, Wery P M; Tijms, Jurgen

2015-08-01

Rapid automatized naming (RAN) is widely seen as an important indicator of dyslexia. The nature of the cognitive processes involved in rapid naming is however still a topic of controversy. We hypothesized that in addition to the involvement of phonological processes and processing speed, RAN is a function of inhibition processes, in particular of interference control. A total 86 children with dyslexia and 31 normal readers were recruited. Our results revealed that in addition to phonological processing and processing speed, interference control predicts rapid naming in dyslexia, but in contrast to these other two cognitive processes, inhibition is not significantly associated with their reading and spelling skills. After variance in reading and spelling associated with processing speed, interference control and phonological processing was partialled out, naming speed was no longer consistently associated with the reading and spelling skills of children with dyslexia. Finally, dyslexic children differed from normal readers on naming speed, literacy skills, phonological processing and processing speed, but not on inhibition processes. Both theoretical and clinical interpretations of these results are discussed. Copyright © 2014 John Wiley & Sons, Ltd.

Controlled Speed Accessory Drive demonstration program

NASA Technical Reports Server (NTRS)

Hoehn, F. W.

1981-01-01

A Controlled Speed Accessory Drive System was examined in an effort to improve the fuel economy of passenger cars. Concept feasibility and the performance of a typical system during actual road driving conditions were demonstrated. The CSAD system is described as a mechanical device which limits engine accessory speeds, thereby reducing parasitic horsepower losses and improving overall vehicle fuel economy. Fuel consumption data were compiled for fleets of GSA vehicles. Various motor pool locations were selected, each representing different climatic conditions. On the basis of a total accumulated fleet usage of nearly three million miles, an overall fuel economy improvement of 6 percent to 7 percent was demonstrated. Coincident chassis dynamometer tests were accomplished on selected vehicles to establish the effect of different accessory drive systems on exhaust emissions, and to evaluate the magnitude of the mileage benefits which could be derived.

Real-time inspection by submarine images

NASA Astrophysics Data System (ADS)

Tascini, Guido; Zingaretti, Primo; Conte, Giuseppe

1996-10-01

A real-time application of computer vision concerning tracking and inspection of a submarine pipeline is described. The objective is to develop automatic procedures for supporting human operators in the real-time analysis of images acquired by means of cameras mounted on underwater remotely operated vehicles (ROV) Implementation of such procedures gives rise to a human-machine system for underwater pipeline inspection that can automatically detect and signal the presence of the pipe, of its structural or accessory elements, and of dangerous or alien objects in its neighborhood. The possibility of modifying the image acquisition rate in the simulations performed on video- recorded images is used to prove that the system performs all necessary processing with an acceptable robustness working in real-time up to a speed of about 2.5 kn, widely greater than that the actual ROVs and the security features allow.

Improved imaging algorithm for bridge crack detection

NASA Astrophysics Data System (ADS)

Lu, Jingxiao; Song, Pingli; Han, Kaihong

2012-04-01

This paper present an improved imaging algorithm for bridge crack detection, through optimizing the eight-direction Sobel edge detection operator, making the positioning of edge points more accurate than without the optimization, and effectively reducing the false edges information, so as to facilitate follow-up treatment. In calculating the crack geometry characteristics, we use the method of extracting skeleton on single crack length. In order to calculate crack area, we construct the template of area by making logical bitwise AND operation of the crack image. After experiment, the results show errors of the crack detection method and actual manual measurement are within an acceptable range, meet the needs of engineering applications. This algorithm is high-speed and effective for automated crack measurement, it can provide more valid data for proper planning and appropriate performance of the maintenance and rehabilitation processes of bridge.

A multiresolution approach to iterative reconstruction algorithms in X-ray computed tomography.

PubMed

De Witte, Yoni; Vlassenbroeck, Jelle; Van Hoorebeke, Luc

2010-09-01

In computed tomography, the application of iterative reconstruction methods in practical situations is impeded by their high computational demands. Especially in high resolution X-ray computed tomography, where reconstruction volumes contain a high number of volume elements (several giga voxels), this computational burden prevents their actual breakthrough. Besides the large amount of calculations, iterative algorithms require the entire volume to be kept in memory during reconstruction, which quickly becomes cumbersome for large data sets. To overcome this obstacle, we present a novel multiresolution reconstruction, which greatly reduces the required amount of memory without significantly affecting the reconstructed image quality. It is shown that, combined with an efficient implementation on a graphical processing unit, the multiresolution approach enables the application of iterative algorithms in the reconstruction of large volumes at an acceptable speed using only limited resources.

Longitudinal Processing Speed Impairments in Males with Autism and the Effects of White Matter Microstructure

PubMed Central

Travers, Brittany G.; Bigler, Erin D.; Tromp, Do P. M.; Adluru, Nagesh; Froehlich, Alyson L.; Ennis, Chad; Lange, Nicholas; Nielsen, Jared A.; Prigge, Molly B. D.; Alexander, Andrew L.; Lainhart, Janet E.

2014-01-01

The present study used an accelerated longitudinal design to examine group differences and age-related changes in processing speed in 81 individuals with Autism Spectrum Disorder (ASD) compared to 56 age-matched individuals with typical development (ages 6–39 years). Processing speed was assessed using the Wechsler Intelligence Scale for Children-3rd edition (WISC-III) and the Wechsler Adult Intelligence Scale-3rd edition (WAIS-III). Follow-up analyses examined processing speed subtest performance and relations between processing speed and white matter microstructure (as measured with diffusion tensor imaging [DTI] in a subset of these participants). After controlling for full scale IQ, the present results show that processing speed index standard scores were on average 12 points lower in the group with ASD compared to the group with typical development. There were, however, no significant group differences in standard score age-related changes within this age range. For subtest raw scores, the group with ASD demonstrated robustly slower processing speeds in the adult versions of the IQ test (i.e., WAIS-III) but not in the child versions (WISC-III), even though age-related changes were similar in both the ASD and typically developing groups. This pattern of results may reflect difficulties that become increasingly evident in ASD on more complex measures of processing speed. Finally, DTI measures of whole-brain white matter microstructure suggested that fractional anisotropy (but not mean diffusivity, radial diffusivity, or axial diffusivity) made significant but small-sized contributions to processing speed standard scores across our entire sample. Taken together, the present findings suggest that robust decreases in processing speed may be present in ASD, more pronounced in adulthood, and partially attributable to white matter microstructural integrity. PMID:24269298

Individual Differences in the Speed of Facial Emotion Recognition Show Little Specificity but Are Strongly Related with General Mental Speed: Psychometric, Neural and Genetic Evidence

PubMed Central

Liu, Xinyang; Hildebrandt, Andrea; Recio, Guillermo; Sommer, Werner; Cai, Xinxia; Wilhelm, Oliver

2017-01-01

Facial identity and facial expression processing are crucial socio-emotional abilities but seem to show only limited psychometric uniqueness when the processing speed is considered in easy tasks. We applied a comprehensive measurement of processing speed and contrasted performance specificity in socio-emotional, social and non-social stimuli from an individual differences perspective. Performance in a multivariate task battery could be best modeled by a general speed factor and a first-order factor capturing some specific variance due to processing emotional facial expressions. We further tested equivalence of the relationships between speed factors and polymorphisms of dopamine and serotonin transporter genes. Results show that the speed factors are not only psychometrically equivalent but invariant in their relation with the Catechol-O-Methyl-Transferase (COMT) Val158Met polymorphism. However, the 5-HTTLPR/rs25531 serotonin polymorphism was related with the first-order factor of emotion perception speed, suggesting a specific genetic correlate of processing emotions. We further investigated the relationship between several components of event-related brain potentials with psychometric abilities, and tested emotion specific individual differences at the neurophysiological level. Results revealed swifter emotion perception abilities to go along with larger amplitudes of the P100 and the Early Posterior Negativity (EPN), when emotion processing was modeled on its own. However, after partialling out the shared variance of emotion perception speed with general processing speed-related abilities, brain-behavior relationships did not remain specific for emotion. Together, the present results suggest that speed abilities are strongly interrelated but show some specificity for emotion processing speed at the psychometric level. At both genetic and neurophysiological levels, emotion specificity depended on whether general cognition is taken into account or not. These findings keenly suggest that general speed abilities should be taken into account when the study of emotion recognition abilities is targeted in its specificity. PMID:28848411

Design-Parameters Setup for Power-Split Dual-Regime IVT

NASA Astrophysics Data System (ADS)

Preda, Ion; Ciolan, Gheorghe; Covaciu, Dinu

2017-10-01

To analyze the working possibilities of power-split infinitely variable transmissions (IVTs) it is necessary to follow a systematic approach. The method proposed in this paper consists of generating a block diagram of the transmission and then, based on this diagram, to derive the kinematics and dynamics equations of the transmission. For an actual numerical case, the derived equations are used to find characteristic values of the transmission components (gear and chain drives, planetary units) necessary to calculate the speed ratios, the speeds, torques and powers acting on the shafts and coupling (control) elements, and even to estimate the overall efficiency of the transmission.

Performance of some miniature pressure transducers subjected to high rotational speeds and centripetal accelerations

NASA Technical Reports Server (NTRS)

Minkin, H. L.

1976-01-01

The performance characteristics of several miniature pressure transducers were determined at centripetal accelerations up to 11,200 g's at a rotational speed of 23,000 rpm. The variation in centripetal acceleration was produced by changing radial position of the transducer relative to the center of rotation. Residual zero outputs and transducer sensitivities were determined at 23,000 rpm and compared with those determined at 0 rpm. The actual pressures at the various transducer locations differ from the center line impressed pressures due to a rotational effect. Corrections for this effect were made. A brief description of the test apparatus is included.

Visual processing speed in old age.

PubMed

Habekost, Thomas; Vogel, Asmus; Rostrup, Egill; Bundesen, Claus; Kyllingsbaek, Søren; Garde, Ellen; Ryberg, Charlotte; Waldemar, Gunhild

2013-04-01

Mental speed is a common concept in theories of cognitive aging, but it is difficult to get measures of the speed of a particular psychological process that are not confounded by the speed of other processes. We used Bundesen's (1990) Theory of Visual Attention (TVA) to obtain specific estimates of processing speed in the visual system controlled for the influence of response latency and individual variations of the perception threshold. A total of 33 non-demented old people (69-87 years) were tested for the ability to recognize briefly presented letters. Performance was analyzed by the TVA model. Visual processing speed decreased approximately linearly with age and was on average halved from 70 to 85 years. Less dramatic aging effects were found for the perception threshold and the visual apprehension span. In the visual domain, cognitive aging seems to be most clearly related to reductions in processing speed. © 2012 The Authors. Scandinavian Journal of Psychology © 2012 The Scandinavian Psychological Associations.

Reaction time, processing speed and sustained attention in schizophrenia: impact on social functioning.

PubMed

Lahera, Guillermo; Ruiz, Alicia; Brañas, Antía; Vicens, María; Orozco, Arantxa

Previous studies have linked processing speed with social cognition and functioning of patients with schizophrenia. A discriminant analysis is needed to determine the different components of this neuropsychological construct. This paper analyzes the impact of processing speed, reaction time and sustained attention on social functioning. 98 outpatients between 18 and 65 with DSM-5 diagnosis of schizophrenia, with a period of 3 months of clinical stability, were recruited. Sociodemographic and clinical data were collected, and the following variables were measured: processing speed (Trail Making Test [TMT], symbol coding [BACS], verbal fluency), simple and elective reaction time, sustained attention, recognition of facial emotions and global functioning. Processing speed (measured only through the BACS), sustained attention (CPT) and elective reaction time (but not simple) were associated with functioning. Recognizing facial emotions (FEIT) correlated significantly with scores on measures of processing speed (BACS, Animals, TMT), sustained attention (CPT) and reaction time. The linear regression model showed a significant relationship between functioning, emotion recognition (P=.015) and processing speed (P=.029). A deficit in processing speed and facial emotion recognition are associated with worse global functioning in patients with schizophrenia. Copyright © 2017 SEP y SEPB. Publicado por Elsevier España, S.L.U. All rights reserved.

Background: What the States Created

ERIC Educational Resources Information Center

Cox, James C.

2009-01-01

Prior to 2003, virtual universities were being created at a rate that would question the usual perception that higher education rarely changed, or changed (if at all) at a glacial speed. No comprehensive study of what was actually being created had been done; nor had anyone tapped the experiences of the developers in the states to see what was…

Estimation of Return Values of Wave Height: Consequences of Missing Observations

ERIC Educational Resources Information Center

Ryden, Jesper

2008-01-01

Extreme-value statistics is often used to estimate so-called return values (actually related to quantiles) for environmental quantities like wind speed or wave height. A basic method for estimation is the method of block maxima which consists in partitioning observations in blocks, where maxima from each block could be considered independent.…

Relationship between Uric Acid Level and Achievement Motivation. Final Report.

ERIC Educational Resources Information Center

Mueller, Ernst F.; French, John R. P., Jr.

In an investigation of the relationship of uric acid (a metabolic end product) to achievement, this study hypothesized that a person's serum urate level (a factor often associated with gout) is positively related to achievement need as well as indicators of actual achievement. (Speed of promotion and number of yearly publications were chosen as…

Information processing speed in obstructive sleep apnea syndrome: a review.

PubMed

Kilpinen, R; Saunamäki, T; Jehkonen, M

2014-04-01

To provide a comprehensive review of studies on information processing speed in patients with obstructive sleep apnea syndrome (OSAS) as compared to healthy controls and normative data, and to determine whether continuous positive airway pressure (CPAP) treatment improves information processing speed. A systematic review was performed on studies drawn from Medline and PsycINFO (January 1990-December 2011) and identified from lists of references in these studies. After inclusion criteria, 159 articles were left for abstract review, and after exclusion criteria 44 articles were fully reviewed. The number of patients in the studies reviewed ranged from 10 to 157 and the study samples consisted mainly of men. Half of the studies reported that patients with OSAS showed reduced information processing speed when compared to healthy controls. Reduced information processing speed was seen more often (75%) when compared to norm-referenced data. Psychomotor speed seemed to be particularly liable to change. CPAP treatment improved processing speed, but the improvement was marginal when compared to placebo or conservative treatment. Patients with OSAS are affected by reduced information processing speed, which may persist despite CPAP treatment. Information processing is usually assessed as part of other cognitive functioning, not as a cognitive domain per se. However, it is important to take account of information processing speed when assessing other aspects of cognitive functioning. This will make it possible to determine whether cognitive decline in patients with OSAS is based on lower-level or higher-level cognitive processes or both. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Gaining control: changing relations between executive control and processing speed and their relevance for mathematics achievement over course of the preschool period

PubMed Central

Clark, Caron A. C.; Nelson, Jennifer Mize; Garza, John; Sheffield, Tiffany D.; Wiebe, Sandra A.; Espy, Kimberly Andrews

2014-01-01

Early executive control (EC) predicts a range of academic outcomes and shows particularly strong associations with children's mathematics achievement. Nonetheless, a major challenge for EC research lies in distinguishing EC from related cognitive constructs that also are linked to achievement outcomes. Developmental cascade models suggest that children's information processing speed is a driving mechanism in cognitive development that supports gains in working memory, inhibitory control and associated cognitive abilities. Accordingly, individual differences in early executive task performance and their relation to mathematics may reflect, at least in part, underlying variation in children's processing speed. The aims of this study were to: (1) examine the degree of overlap between EC and processing speed at different preschool age points; and (2) determine whether EC uniquely predicts children's mathematics achievement after accounting for individual differences in processing speed. As part of a longitudinal, cohort-sequential study, 388 children (50% boys; 44% from low income households) completed the same battery of EC tasks at ages 3, 3.75, 4.5, and 5.25 years. Several of the tasks incorporated baseline speeded naming conditions with minimal EC demands. Multidimensional latent models were used to isolate the variance in executive task performance that did not overlap with baseline processing speed, covarying for child language proficiency. Models for separate age points showed that, while EC did not form a coherent latent factor independent of processing speed at age 3 years, it did emerge as a distinct factor by age 5.25. Although EC at age 3 showed no distinct relation with mathematics achievement independent of processing speed, EC at ages 3.75, 4.5, and 5.25 showed independent, prospective links with mathematics achievement. Findings suggest that EC and processing speed are tightly intertwined in early childhood. As EC becomes progressively decoupled from processing speed with age, it begins to take on unique, discriminative importance for children's mathematics achievement. PMID:24596563

Visual function and cognitive speed of processing mediate age-related decline in memory span and fluid intelligence

PubMed Central

Clay, Olivio J.; Edwards, Jerri D.; Ross, Lesley A.; Okonkwo, Ozioma; Wadley, Virginia G.; Roth, David L.; Ball, Karlene K.

2010-01-01

Objectives: To evaluate the relationship between sensory and cognitive decline, particularly with respect to speed of processing, memory span, and fluid intelligence. Additionally, the common cause, sensory degradation and speed of processing hypotheses were compared. Methods: Structural equation modeling was used to investigate the complex relationships among age-related decrements in these areas. Results: Cross-sectional data analyses included 842 older adult participants (M = 73 years). After accounting for age-related declines in vision and processing speed, the direct associations between age and memory span and between age and fluid intelligence were nonsignificant. Older age was associated with visual decline, which was associated with slower speed of processing, which in turn was associated with greater cognitive deficits. Discussion: The findings support both the sensory degradation and speed of processing accounts of age-related cognitive decline. Further, the findings highlight positive aspects of normal cognitive aging in that older age may not be associated with a loss of fluid intelligence if visual sensory functioning and processing speed can be maintained. PMID:19436063

Mate preferences do predict attraction and choices in the early stages of mate selection.

PubMed

Li, Norman P; Yong, Jose C; Tov, William; Sng, Oliver; Fletcher, Garth J O; Valentine, Katherine A; Jiang, Yun F; Balliet, Daniel

2013-11-01

Although mate preference research has firmly established that men value physical attractiveness more than women do and women value social status more than men do, recent speed-dating studies have indicated mixed evidence (at best) for whether people's sex-differentiated mate preferences predict actual mate choices. According to an evolutionary, mate preference priority model (Li, Bailey, Kenrick, & Linsenmeier, 2002; Li & Kenrick, 2006; Li, Valentine, & Patel, 2011), the sexes are largely similar in what they ideally like, but for long-term mates, they should differ on what they most want to avoid in early selection contexts. Following this model, we conducted experiments using online messaging and modified speed-dating platforms. Results indicate that when a mating pool includes people at the low end of social status and physical attractiveness, mate choice criteria are sex-differentiated: Men, more than women, chose mates based on physical attractiveness, whereas women, more than men, chose mates based on social status. In addition, individuals who more greatly valued social status or physical attractiveness on paper valued these traits more in their actual choices. In particular, mate choices were sex-differentiated when considering long-term relationships but not short-term ones, where both sexes shunned partners with low physical attractiveness. The findings validate a large body of mate preferences research and an evolutionary perspective on mating, and they have implications for research using speed-dating and other interactive contexts. PsycINFO Database Record (c) 2013 APA, all rights reserved.

New breathing functions for the transverse breathing crack of the cracked rotor system: Approach for critical and subcritical harmonic analysis

NASA Astrophysics Data System (ADS)

Al-Shudeifat, Mohammad A.; Butcher, Eric A.

2011-01-01

The actual breathing mechanism of the transverse breathing crack in the cracked rotor system that appears due to the shaft weight is addressed here. As a result, the correct time-varying area moments of inertia for the cracked element cross-section during shaft rotation are also determined. Hence, two new breathing functions are identified to represent the actual breathing effect on the cracked element stiffness matrix. The new breathing functions are used in formulating the time-varying finite element stiffness matrix of the cracked element. The finite element equations of motion are then formulated for the cracked rotor system and solved via harmonic balance method for response, whirl orbits and the shift in the critical and subcritical speeds. The analytical results of this approach are compared with some previously published results obtained using approximate formulas for the breathing mechanism. The comparison shows that the previously used breathing function is a weak model for the breathing mechanism in the cracked rotor even for small crack depths. The new breathing functions give more accurate results for the dynamic behavior of the cracked rotor system for a wide range of the crack depths. The current approach is found to be efficient for crack detection since the critical and subcritical shaft speeds, the unique vibration signature in the neighborhood of the subcritical speeds and the sensitivity to the unbalance force direction all together can be utilized to detect the breathing crack before further damage occurs.

The role of explicit and implicit standards in visual speed discrimination.

PubMed

Norman, J Farley; Pattison, Kristina F; Norman, Hideko F; Craft, Amy E; Wiesemann, Elizabeth Y; Taylor, M Jett

2008-01-01

Five experiments were designed to investigate visual speed discrimination. Variations of the method of constant stimuli were used to obtain speed discrimination thresholds in experiments 1, 2, 4, and 5, while the method of single stimuli was used in experiment 3. The observers' thresholds were significantly influenced by the choice of psychophysical method and by changes in the standard speed. The observers' judgments were unaffected, however, by changes in the magnitude of random variations in stimulus duration, reinforcing the conclusions of Lappin et al (1975 Journal of Experimental Psychology: Human Perception and Performance 1 383 394). When an implicit standard was used, the observers produced relatively low discrimination thresholds (7.0% of the standard speed), verifying the results of McKee (1981 Vision Research 21 491-500). When an explicit standard was used in a 2AFC variant of the method of constant stimuli, however, the observers' discrimination thresholds increased by 74% (to 12.2%), resembling the high thresholds obtained by Mandriota et al (1962 Science 138 437-438). A subsequent signal-detection analysis revealed that the observers' actual sensitivities to differences in speed were in fact equivalent for both psychophysical methods. The formation of an implicit standard in the method of single stimuli allows human observers to make judgments of speed that are as precise as those obtained when explicit standards are available.

A 45° saw-dicing process applied to a glass substrate for wafer-level optical splitter fabrication for optical coherence tomography

NASA Astrophysics Data System (ADS)

Maciel, M. J.; Costa, C. G.; Silva, M. F.; Gonçalves, S. B.; Peixoto, A. C.; Ribeiro, A. Fernando; Wolffenbuttel, R. F.; Correia, J. H.

2016-08-01

This paper reports on the development of a technology for the wafer-level fabrication of an optical Michelson interferometer, which is an essential component in a micro opto-electromechanical system (MOEMS) for a miniaturized optical coherence tomography (OCT) system. The MOEMS consists on a titanium dioxide/silicon dioxide dielectric beam splitter and chromium/gold micro-mirrors. These optical components are deposited on 45° tilted surfaces to allow the horizontal/vertical separation of the incident beam in the final micro-integrated system. The fabrication process consists of 45° saw dicing of a glass substrate and the subsequent deposition of dielectric multilayers and metal layers. The 45° saw dicing is fully characterized in this paper, which also includes an analysis of the roughness. The optimum process results in surfaces with a roughness of 19.76 nm (rms). The actual saw dicing process for a high-quality final surface results as a compromise between the dicing blade’s grit size (#1200) and the cutting speed (0.3 mm s-1). The proposed wafer-level fabrication allows rapid and low-cost processing, high compactness and the possibility of wafer-level alignment/assembly with other optical micro components for OCT integrated imaging.

Effects of information processing speed on learning, memory, and executive functioning in people living with HIV/AIDS.

PubMed

Fellows, Robert P; Byrd, Desiree A; Morgello, Susan

2014-01-01

It is unclear whether or to what degree literacy, aging, and other neurologic abnormalities relate to cognitive deficits among people living with HIV/AIDS in the combined antiretroviral therapy (CART) era. The primary aim of this study was to simultaneously examine the association of age, HIV-associated motor abnormalities, major depressive disorder, and reading level with information processing speed, learning, memory, and executive functions, and to determine whether processing speed mediated any of the relationships between cognitive and noncognitive variables. Participants were 186 racially and ethnically diverse men and women living with HIV/AIDS who underwent comprehensive neurological, neuropsychological, and medical evaluations. Structural equation modeling was utilized to assess the extent to which information processing speed mediated the relationship between age, motor abnormalities, major depressive disorder, and reading level with other cognitive abilities. Age, motor dysfunction, reading level, and current major depressive disorder were all significantly associated with information processing speed. Information processing speed fully mediated the effects of age on learning, memory, and executive functioning and partially mediated the effect of major depressive disorder on learning and memory. The effect of motor dysfunction on learning and memory was fully mediated by processing speed. These findings provide support for information processing speed as a primary deficit, which may account, at least in part, for many of the other cognitive abnormalities recognized in complex HIV/AIDS populations. The association of age and information processing speed may account for HIV/aging synergies in the generation of CART-era cognitive abnormalities.

Two-dimensional shear wave speed and crawling wave speed recoveries from in vitro prostate data

PubMed Central

Lin, Kui; McLaughlin, Joyce R.; Thomas, Ashley; Parker, Kevin; Castaneda, Benjamin; Rubens, Deborah J.

2011-01-01

The crawling wave experiment was developed to capture a shear wave induced moving interference pattern that is created by two harmonic vibration sources oscillating at different but almost the same frequencies. Using the vibration sonoelastography technique, the spectral variance image reveals a moving interference pattern. It has been shown that the speed of the moving interference pattern, i.e., the crawling wave speed, is proportional to the shear wave speed with a nonlinear factor. This factor can generate high-speed artifacts in the crawling wave speed images that do not actually correspond to increased stiffness. In this paper, an inverse algorithm is developed to reconstruct both the crawling wave speed and the shear wave speed using the phases of the crawling wave and the shear wave. The feature for the data is the application to in vitro prostate data, while the features for the algorithm include the following: (1) A directional filter is implemented to obtain a wave moving in only one direction; and (2) an L1 minimization technique with physics inspired constraints is employed to calculate the phase of the crawling wave and to eliminate jump discontinuities from the phase of the shear wave. The algorithm is tested on in vitro prostate data measured at the Rochester Center for Biomedical Ultrasound and University of Rochester. Each aspect of the algorithm is shown to yield image improvement. The results demonstrate that the shear wave speed images can have less artifacts than the crawling wave images. Examples are presented where the shear wave speed recoveries have excellent agreement with histology results on the size, shape, and location of cancerous tissues in the glands. PMID:21786924

New geometric design consistency model based on operating speed profiles for road safety evaluation.

PubMed

Camacho-Torregrosa, Francisco J; Pérez-Zuriaga, Ana M; Campoy-Ungría, J Manuel; García-García, Alfredo

2013-12-01

To assist in the on-going effort to reduce road fatalities as much as possible, this paper presents a new methodology to evaluate road safety in both the design and redesign stages of two-lane rural highways. This methodology is based on the analysis of road geometric design consistency, a value which will be a surrogate measure of the safety level of the two-lane rural road segment. The consistency model presented in this paper is based on the consideration of continuous operating speed profiles. The models used for their construction were obtained by using an innovative GPS-data collection method that is based on continuous operating speed profiles recorded from individual drivers. This new methodology allowed the researchers to observe the actual behavior of drivers and to develop more accurate operating speed models than was previously possible with spot-speed data collection, thereby enabling a more accurate approximation to the real phenomenon and thus a better consistency measurement. Operating speed profiles were built for 33 Spanish two-lane rural road segments, and several consistency measurements based on the global and local operating speed were checked. The final consistency model takes into account not only the global dispersion of the operating speed, but also some indexes that consider both local speed decelerations and speeds over posted speeds as well. For the development of the consistency model, the crash frequency for each study site was considered, which allowed estimating the number of crashes on a road segment by means of the calculation of its geometric design consistency. Consequently, the presented consistency evaluation method is a promising innovative tool that can be used as a surrogate measure to estimate the safety of a road segment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Using Active Learning for Speeding up Calibration in Simulation Models.

PubMed

Cevik, Mucahit; Ergun, Mehmet Ali; Stout, Natasha K; Trentham-Dietz, Amy; Craven, Mark; Alagoz, Oguzhan

2016-07-01

Most cancer simulation models include unobservable parameters that determine disease onset and tumor growth. These parameters play an important role in matching key outcomes such as cancer incidence and mortality, and their values are typically estimated via a lengthy calibration procedure, which involves evaluating a large number of combinations of parameter values via simulation. The objective of this study is to demonstrate how machine learning approaches can be used to accelerate the calibration process by reducing the number of parameter combinations that are actually evaluated. Active learning is a popular machine learning method that enables a learning algorithm such as artificial neural networks to interactively choose which parameter combinations to evaluate. We developed an active learning algorithm to expedite the calibration process. Our algorithm determines the parameter combinations that are more likely to produce desired outputs and therefore reduces the number of simulation runs performed during calibration. We demonstrate our method using the previously developed University of Wisconsin breast cancer simulation model (UWBCS). In a recent study, calibration of the UWBCS required the evaluation of 378 000 input parameter combinations to build a race-specific model, and only 69 of these combinations produced results that closely matched observed data. By using the active learning algorithm in conjunction with standard calibration methods, we identify all 69 parameter combinations by evaluating only 5620 of the 378 000 combinations. Machine learning methods hold potential in guiding model developers in the selection of more promising parameter combinations and hence speeding up the calibration process. Applying our machine learning algorithm to one model shows that evaluating only 1.49% of all parameter combinations would be sufficient for the calibration. © The Author(s) 2015.

Quantification of the resist dissolution process: an in situ analysis using high speed atomic force microscopy

NASA Astrophysics Data System (ADS)

Santillan, Julius Joseph; Shichiri, Motoharu; Itani, Toshiro

2016-03-01

This work focuses on the application of a high speed atomic force microscope (HS-AFM) for the in situ visualization / quantification of the resist dissolution process. This technique, as reported in the past, has provided useful pointers on the formation of resist patterns during dissolution. This paper discusses about an investigation made on the quantification of what we refer to as "dissolution unit size" or the basic units of patterning material dissolution. This was done through the establishment of an originally developed analysis method which extracts the difference between two succeeding temporal states of the material film surface (images) to indicate the amount of change occurring in the material film at a specific span of time. Preliminary experiments with actual patterning materials were done using a positive-tone EUV model resist composed only of polyhydroxystyrene (PHS)-based polymer with a molecular weight of 2,500 and a polydispersity index of 1.2. In the absence of a protecting group, the material was utilized at a 50nm film thickness with post application bake of 90°C/60s. The resulting film is soluble in the alkali-based developer even without exposure. Results have shown that the dissolution components (dissolution unit size) of the PHS-based material are not of fixed size. Instead, it was found that aside from one constantly dissolving unit size, another, much larger dissolution unit size trend also occurs during material dissolution. The presence of this larger dissolution unit size suggests an occurrence of "polymer clustering". Such polymer clustering was not significantly present during the initial stages of dissolution (near the original film surface) but becomes more persistently obvious after the dissolution process reaches a certain film thickness below the initial surface.

Optimising research to speed up availability of paediatric antiretroviral drugs and formulations

PubMed Central

Penazzato, M; Gnanashanmugam, D; Rojo, P; Lallemant, M; Lewis, L; Rocchi, F; Saint Raymond, A; Ford, N; Hazra, R; Giaquinto, C; Gibb, D; Abrams, Elaine J

2018-01-01

Globally 1.8 million children are estimated to be living with HIV, yet only 51% of those eligible actually start treatment. The completion of research and development (R&D) for paediatric antiretrovirals (ARVs) is a lengthy process and licensing of new paediatric ARVs continues to lag considerably behind adults. Providing safe, effective, and well-tolerated drugs for children remains critical to ensuring scale-up of paediatric treatment globally. In this manuscript we review current approaches to R&D for paediatric ARVs and suggest innovations to enable simplified, faster, and more comprehensive strategies to develop optimal formulations. Several approaches could be adopted, including enrolment of multiple age-cohorts concurrently and the early introduction of dosing approaches for both single and fixed-dose combination (FDC) drug formulations (preferably scored and dispersible) that match WHO weight-bands. Efforts to speed up development of optimal drugs and formulations for children should focus on a limited number of prioritised formulations. This work should build upon existing partnerships and collaborations to ensure that paediatric investigation plans are developed early in the drug development process but can be modified in a streamlined manner as more information becomes available. In addition, simplified and more efficient mechanisms to undertake R&D need to be put in place, and financing mechanisms must be made more efficient and sustainable. Registration, implementation, and strategic use of drugs should not be seen as a sequential process, with research designed to address multiple questions simultaneously to respond to the needs of HIV-infected children where they live. It is imperative that lessons learned from HIV should be shared to support progress in developing paediatric formulations for other diseases with similar treatment challenges, including tuberculosis and viral hepatitis. PMID:29190337

Using Active Learning for Speeding up Calibration in Simulation Models

PubMed Central

Cevik, Mucahit; Ali Ergun, Mehmet; Stout, Natasha K.; Trentham-Dietz, Amy; Craven, Mark; Alagoz, Oguzhan

2015-01-01

Background Most cancer simulation models include unobservable parameters that determine the disease onset and tumor growth. These parameters play an important role in matching key outcomes such as cancer incidence and mortality and their values are typically estimated via lengthy calibration procedure, which involves evaluating large number of combinations of parameter values via simulation. The objective of this study is to demonstrate how machine learning approaches can be used to accelerate the calibration process by reducing the number of parameter combinations that are actually evaluated. Methods Active learning is a popular machine learning method that enables a learning algorithm such as artificial neural networks to interactively choose which parameter combinations to evaluate. We develop an active learning algorithm to expedite the calibration process. Our algorithm determines the parameter combinations that are more likely to produce desired outputs, therefore reduces the number of simulation runs performed during calibration. We demonstrate our method using previously developed University of Wisconsin Breast Cancer Simulation Model (UWBCS). Results In a recent study, calibration of the UWBCS required the evaluation of 378,000 input parameter combinations to build a race-specific model and only 69 of these combinations produced results that closely matched observed data. By using the active learning algorithm in conjunction with standard calibration methods, we identify all 69 parameter combinations by evaluating only 5620 of the 378,000 combinations. Conclusion Machine learning methods hold potential in guiding model developers in the selection of more promising parameter combinations and hence speeding up the calibration process. Applying our machine learning algorithm to one model shows that evaluating only 1.49% of all parameter combinations would be sufficient for the calibration. PMID:26471190

Apathy and Reduced Speed of Processing Underlie Decline in Verbal Fluency following DBS.

PubMed

Foley, Jennifer A; Foltynie, Tom; Zrinzo, Ludvic; Hyam, Jonathan A; Limousin, Patricia; Cipolotti, Lisa

2017-01-01

Objective . Reduced verbal fluency is a strikingly uniform finding following deep brain stimulation (DBS) for Parkinson's disease (PD). The precise cognitive mechanism underlying this reduction remains unclear, but theories have suggested reduced motivation, linguistic skill, and/or executive function. It is of note, however, that previous reports have failed to consider the potential role of any changes in speed of processing. Thus, the aim of this study was to examine verbal fluency changes with a particular focus on the role of cognitive speed. Method . In this study, 28 patients with PD completed measures of verbal fluency, motivation, language, executive functioning, and speed of processing, before and after DBS. Results . As expected, there was a marked decline in verbal fluency but also in a timed test of executive functions and two measures of speed of processing. Verbal fluency decline was associated with markers of linguistic and executive functioning, but not after speed of processing was statistically controlled for. In contrast, greater decline in verbal fluency was associated with higher levels of apathy at baseline, which was not associated with changes in cognitive speed. Discussion . Reduced generativity and processing speed may account for the marked reduction in verbal fluency commonly observed following DBS.

Relationship between speed and EEG activity during imagined and executed hand movements

NASA Astrophysics Data System (ADS)

Yuan, Han; Perdoni, Christopher; He, Bin

2010-04-01

The relationship between primary motor cortex and movement kinematics has been shown in nonhuman primate studies of hand reaching or drawing tasks. Studies have demonstrated that the neural activities accompanying or immediately preceding the movement encode the direction, speed and other information. Here we investigated the relationship between the kinematics of imagined and actual hand movement, i.e. the clenching speed, and the EEG activity in ten human subjects. Study participants were asked to perform and imagine clenching of the left hand and right hand at various speeds. The EEG activity in the alpha (8-12 Hz) and beta (18-28 Hz) frequency bands were found to be linearly correlated with the speed of imagery clenching. Similar parametric modulation was also found during the execution of hand movements. A single equation relating the EEG activity to the speed and the hand (left versus right) was developed. This equation, which contained a linear independent combination of the two parameters, described the time-varying neural activity during the tasks. Based on the model, a regression approach was developed to decode the two parameters from the multiple-channel EEG signals. We demonstrated the continuous decoding of dynamic hand and speed information of the imagined clenching. In particular, the time-varying clenching speed was reconstructed in a bell-shaped profile. Our findings suggest an application to providing continuous and complex control of noninvasive brain-computer interface for movement-impaired paralytics.

Information processing speed and attention in multiple sclerosis: Reconsidering the Attention Network Test (ANT).

PubMed

Roth, Alexandra K; Denney, Douglas R; Lynch, Sharon G

2015-01-01

The Attention Network Test (ANT) assesses attention in terms of discrepancies between response times to items that differ in the burden they place on some facet of attention. However, simple arithmetic difference scores commonly used to capture these discrepancies fail to provide adequate control for information processing speed, leading to distorted findings when patient and control groups differ markedly in the speed with which they process and respond to stimulus information. This study examined attention networks in patients with multiple sclerosis (MS) using simple difference scores, proportional scores, and residualized scores that control for processing speed through statistical regression. Patients with relapsing-remitting (N = 20) or secondary progressive (N = 20) MS and healthy controls (N = 40) of similar age, education, and gender completed the ANT. Substantial differences between patients and controls were found on all measures of processing speed. Patients exhibited difficulties in the executive control network, but only when difference scores were considered. When deficits in information processing speed were adequately controlled using proportional or residualized score, deficits in the alerting network emerged. The effect sizes for these deficits were notably smaller than those for overall information processing speed and were also limited to patients with secondary progressive MS. Deficits in processing speed are more prominent in MS than those involving attention, and when the former are properly accounted for, differences in the latter are confined to the alerting network.

Processing Speed Predicts Behavioral Treatment Outcomes in Children with Attention-Deficit/Hyperactivity Disorder Predominantly Inattentive Type.

PubMed

Adalio, Christopher J; Owens, Elizabeth B; McBurnett, Keith; Hinshaw, Stephen P; Pfiffner, Linda J

2018-05-01

Neuropsychological functioning underlies behavioral symptoms of attention-deficit/hyperactivity disorder (ADHD). Children with all forms of ADHD are vulnerable to working memory deficits and children presenting with the inattentive form of ADHD (ADHD-I) appear particularly vulnerable to processing speed deficits. As ADHD-I is the most common form of ADHD presented by children in community settings, it is important to consider how treatment interventions for children with ADHD-I may be affected by deficits in processing speed and working memory. We utilize data collected from 199 children with ADHD-I, aged 7 to 11 years, who participated in a randomized clinical trial of a psychosocial-behavioral intervention. Our aims are first to determine whether processing speed or working memory predict treatment outcomes in ADHD-I symptom severity, and second whether they moderate treatment effects on ADHD-I symptom severity. Results of linear regression analyses reveal that baseline processing speed significantly predicts posttreatment ADHD-I symptom severity when controlling for baseline ADHD-I symptom severity, such that better processing speed is associated with greater symptom improvement. However, predictive effects of working memory and moderation effects of both working memory and processing speed are not supported in the present study. We discuss study limitations and implications of the relation between processing speed and treatment benefits from psychosocial treatments for children with ADHD-I.

Neonatal Brain Pathology Predicts Adverse Attention and Processing Speed Outcomes in Very Preterm and/or Very Low Birth Weight Children

PubMed Central

Murray, Andrea L; Scratch, Shannon E; Thompson, Deanne K; Inder, Terrie E; Doyle, Lex W; Anderson, Jacqueline F. I.; Anderson, Peter J

2014-01-01

Objective This study aimed to examine attention and processing speed outcomes in very preterm (VPT; <32 weeks' gestational age) or very low birth weight (VLBW; <1500 g) children, and to assess the ability of brain abnormalities measured by neonatal magnetic resonance imaging (MRI) to predict outcome in these domains. Methods A cohort of 198 children born <30 weeks' gestational age and/or <1250 g and 70 term controls were examined. Neonatal MRI scans at term equivalent age were quantitatively assessed for white matter, cortical gray matter, deep gray matter, and cerebellar abnormalities. Attention and processing speed were assessed at 7 years using standardized neuropsychological tests. Group differences were tested in attention and processing speed, and the relationships between these cognitive domains and brain abnormalities at birth were investigated. Results At 7 years of age, the VPT/VLBW group performed significantly poorer than term controls on all attention and processing speed outcomes. Associations between adverse attention and processing speed performances at 7 years and higher neonatal brain abnormality scores were found; in particular, white matter and deep gray matter abnormalities were reasonable predictors of long-term cognitive outcomes. Conclusion Attention and processing speed are significant areas of concern in VPT/VLBW children. This is the first study to show that adverse attention and processing speed outcomes at 7 years are associated with neonatal brain pathology. PMID:24708047

Neonatal brain pathology predicts adverse attention and processing speed outcomes in very preterm and/or very low birth weight children.

PubMed

Murray, Andrea L; Scratch, Shannon E; Thompson, Deanne K; Inder, Terrie E; Doyle, Lex W; Anderson, Jacqueline F I; Anderson, Peter J

2014-07-01

This study aimed to examine attention and processing speed outcomes in very preterm (VPT; < 32 weeks' gestational age) or very low birth weight (VLBW; < 1,500 g) children, and to determine whether brain abnormality measured by neonatal MRI can be used to predict outcome in these domains. A cohort of 198 children born < 30 weeks' gestational age and/or < 1,250 g and 70 term controls were examined. Neonatal MRI scans at term equivalent age were quantitatively assessed for white matter, cortical gray matter, deep gray matter, and cerebellar abnormalities. Attention and processing speed were assessed at 7 years using standardized neuropsychological tests. Group differences were tested in attention and processing speed, and the relationships between these cognitive domains and brain abnormalities at birth were investigated. At 7 years of age, the VPT/VLBW group performed significantly poorer than term controls on all attention and processing speed outcomes. Associations between adverse attention and processing speed performances at 7 years and higher neonatal brain abnormality scores were found; in particular, white matter and deep gray matter abnormalities were reasonable predictors of long-term cognitive outcomes. Attention and processing speed are significant areas of concern in VPT/VLBW children. This is the first study to show that adverse attention and processing speed outcomes at 7 years are associated with neonatal brain pathology.

Women's perceptions, expectations and satisfaction with induced labour--a questionnaire-based study.

PubMed

Shetty, Ashalatha; Burt, Rhona; Rice, Pat; Templeton, Allan

2005-11-01

To evaluate the understanding and expectations of women undergoing labour induction, to assess their actual experience of the process and to compare their satisfaction with labour to those labouring spontaneously. Four hundred and fifty women at term undergoing induction of labour and cervical ripening with prostaglandinE2 vaginal tablets and 450 women labouring spontaneously were recruited into the study. The induction group were requested to complete a questionnaire prior to the start of their induction process and another questionnaire post-delivery. The post-delivery questionnaire contained two sections, one pertaining to issues to do with the induction and the second with the actual labour process. The spontaneously labouring group was requested to complete a questionnaire post-delivery, which only contained the section pertaining to the actual labour process. The main outcome measures were satisfaction with labour, perception of pain and length of labour between the induced and spontaneous labour groups, and issues that the women might wish changed about their induction. In the induction group, 34.7% were not satisfied with the information they received about the induction prior to the procedure and 27.2% expected to deliver within 12h of the administration of the inducing agent. Post-induction, 40% of the women felt the most important aspect they would like to change about their induction were they to have another one, would be the speed of the induction, 13.6% felt they might wish to take the inducing agent orally, 7% to have fewer vaginal examinations and 9% to have fewer complications. Among the women who returned questionnaires, 26.3% had a caesarean delivery in the induction group and 21.4% in the spontaneous labour group. Significantly more women were satisfied with their labour in the spontaneous labour group 79.5% versus 70.4%, RR 0.89, 95% CI 0.8-0.96, P=0.006). Labour that is artificially induced does result in lower satisfaction rates as compared to that following spontaneous onset. The longer time delay between the start of the induction and the delivery plays a significant part in this, with the mode of administration of the inducing agent, more vaginal examinations and the increase in caesarean deliveries being perceived as secondary issues. There is a need to improve the information provided to women undergoing labour induction, to counter unrealistic expectations and thereby improve satisfaction.

Dynamic Simulation Research on Chain Drive Mechanism of Corn Seeder Based on ADAMS

NASA Astrophysics Data System (ADS)

Wang, Y. B.; Jia, H. P.

2017-12-01

In order to reduce the damage to the chain and improve the seeding quality of the seeding machine, the corn seeder has the characteristics of the seeding quality and some technical indexes in the work of the corn seeding machine. The dynamic analysis of the chain drive mechanism is carried out by using the dynamic virtual prototype. In this paper, the speed of the corn planter is 5km/h, and the speed of the simulated knuckle is 0.1~0.9s. The velocity is 0.12m/s, which is equal to the chain speed when the seeder is running normally. Of the dynamic simulation of the movement and the actual situation is basically consistent with the apparent speed of the drive wheel has changed the acceleration and additional dynamic load, the chain drive has a very serious damage, and the maximum load value of 47.28N, in order to reduce the damage to the chain, As far as possible so that the sowing machine in the work to maintain a reasonable uniform speed, to avoid a greater acceleration, the corn sowing machine drive the design of a certain reference.

Applications of High-speed motion analysis system on Solid Rocket Motor (SRM)

NASA Astrophysics Data System (ADS)

Liu, Yang; He, Guo-qiang; Li, Jiang; Liu, Pei-jin; Chen, Jian

2007-01-01

High-speed motion analysis system could record images up to 12,000fps and analyzed with the image processing system. The system stored data and images directly in electronic memory convenient for managing and analyzing. The high-speed motion analysis system and the X-ray radiography system were established the high-speed real-time X-ray radiography system, which could diagnose and measure the dynamic and high-speed process in opaque. The image processing software was developed for improve quality of the original image for acquiring more precise information. The typical applications of high-speed motion analysis system on solid rocket motor (SRM) were introduced in the paper. The research of anomalous combustion of solid propellant grain with defects, real-time measurement experiment of insulator eroding, explosion incision process of motor, structure and wave character of plume during the process of ignition and flameout, measurement of end burning of solid propellant, measurement of flame front and compatibility between airplane and missile during the missile launching were carried out using high-speed motion analysis system. The significative results were achieved through the research. Aim at application of high-speed motion analysis system on solid rocket motor, the key problem, such as motor vibrancy, electrical source instability, geometry aberrance, and yawp disturbance, which damaged the image quality, was solved. The image processing software was developed which improved the capability of measuring the characteristic of image. The experimental results showed that the system was a powerful facility to study instantaneous and high-speed process in solid rocket motor. With the development of the image processing technique, the capability of high-speed motion analysis system was enhanced.

The impact of command signal power distribution, processing delays, and speed scaling on neurally-controlled devices.

PubMed

Marathe, A R; Taylor, D M

2015-08-01

Decoding algorithms for brain-machine interfacing (BMI) are typically only optimized to reduce the magnitude of decoding errors. Our goal was to systematically quantify how four characteristics of BMI command signals impact closed-loop performance: (1) error magnitude, (2) distribution of different frequency components in the decoding errors, (3) processing delays, and (4) command gain. To systematically evaluate these different command features and their interactions, we used a closed-loop BMI simulator where human subjects used their own wrist movements to command the motion of a cursor to targets on a computer screen. Random noise with three different power distributions and four different relative magnitudes was added to the ongoing cursor motion in real time to simulate imperfect decoding. These error characteristics were tested with four different visual feedback delays and two velocity gains. Participants had significantly more trouble correcting for errors with a larger proportion of low-frequency, slow-time-varying components than they did with jittery, higher-frequency errors, even when the error magnitudes were equivalent. When errors were present, a movement delay often increased the time needed to complete the movement by an order of magnitude more than the delay itself. Scaling down the overall speed of the velocity command can actually speed up target acquisition time when low-frequency errors and delays are present. This study is the first to systematically evaluate how the combination of these four key command signal features (including the relatively-unexplored error power distribution) and their interactions impact closed-loop performance independent of any specific decoding method. The equations we derive relating closed-loop movement performance to these command characteristics can provide guidance on how best to balance these different factors when designing BMI systems. The equations reported here also provide an efficient way to compare a diverse range of decoding options offline.

The impact of command signal power distribution, processing delays, and speed scaling on neurally-controlled devices

NASA Astrophysics Data System (ADS)

Marathe, A. R.; Taylor, D. M.

2015-08-01

Objective. Decoding algorithms for brain-machine interfacing (BMI) are typically only optimized to reduce the magnitude of decoding errors. Our goal was to systematically quantify how four characteristics of BMI command signals impact closed-loop performance: (1) error magnitude, (2) distribution of different frequency components in the decoding errors, (3) processing delays, and (4) command gain. Approach. To systematically evaluate these different command features and their interactions, we used a closed-loop BMI simulator where human subjects used their own wrist movements to command the motion of a cursor to targets on a computer screen. Random noise with three different power distributions and four different relative magnitudes was added to the ongoing cursor motion in real time to simulate imperfect decoding. These error characteristics were tested with four different visual feedback delays and two velocity gains. Main results. Participants had significantly more trouble correcting for errors with a larger proportion of low-frequency, slow-time-varying components than they did with jittery, higher-frequency errors, even when the error magnitudes were equivalent. When errors were present, a movement delay often increased the time needed to complete the movement by an order of magnitude more than the delay itself. Scaling down the overall speed of the velocity command can actually speed up target acquisition time when low-frequency errors and delays are present. Significance. This study is the first to systematically evaluate how the combination of these four key command signal features (including the relatively-unexplored error power distribution) and their interactions impact closed-loop performance independent of any specific decoding method. The equations we derive relating closed-loop movement performance to these command characteristics can provide guidance on how best to balance these different factors when designing BMI systems. The equations reported here also provide an efficient way to compare a diverse range of decoding options offline.

High powered rocketry: design, construction, and launching experience and analysis

NASA Astrophysics Data System (ADS)

Paulson, Pryce; Curtis, Jarret; Bartel, Evan; Owens Cyr, Waycen; Lamsal, Chiranjivi

2018-01-01

In this study, the nuts and bolts of designing and building a high powered rocket have been presented. A computer simulation program called RockSim was used to design the rocket. Simulation results are consistent with time variations of altitude, velocity, and acceleration obtained in the actual flight. The actual drag coefficient was determined by using altitude back-tracking method and found to be 0.825. Speed of the exhaust determined to be 2.5 km s-1 by analyzing the thrust curve of the rocket. Acceleration in the coasting phase of the flight, represented by the second-degree polynomial of a small leading coefficient, have been found to approach ‘-g’ asymptotically.

SU-E-J-150: Four-Dimensional Cone-Beam CT Algorithm by Extraction of Physical and Motion Parameter of Mobile Targets Retrospective to Image Reconstruction with Motion Modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ali, I; Ahmad, S; Alsbou, N

Purpose: To develop 4D-cone-beam CT (CBCT) algorithm by motion modeling that extracts actual length, CT numbers level and motion amplitude of a mobile target retrospective to image reconstruction by motion modeling. Methods: The algorithm used three measurable parameters: apparent length and blurred CT number distribution of a mobile target obtained from CBCT images to determine actual length, CT-number value of the stationary target, and motion amplitude. The predictions of this algorithm were tested with mobile targets that with different well-known sizes made from tissue-equivalent gel which was inserted into a thorax phantom. The phantom moved sinusoidally in one-direction to simulatemore » respiratory motion using eight amplitudes ranging 0–20mm. Results: Using this 4D-CBCT algorithm, three unknown parameters were extracted that include: length of the target, CT number level, speed or motion amplitude for the mobile targets retrospective to image reconstruction. The motion algorithms solved for the three unknown parameters using measurable apparent length, CT number level and gradient for a well-defined mobile target obtained from CBCT images. The motion model agreed with measured apparent lengths which were dependent on the actual target length and motion amplitude. The gradient of the CT number distribution of the mobile target is dependent on the stationary CT number level, actual target length and motion amplitude. Motion frequency and phase did not affect the elongation and CT number distribution of the mobile target and could not be determined. Conclusion: A 4D-CBCT motion algorithm was developed to extract three parameters that include actual length, CT number level and motion amplitude or speed of mobile targets directly from reconstructed CBCT images without prior knowledge of the stationary target parameters. This algorithm provides alternative to 4D-CBCT without requirement to motion tracking and sorting of the images into different breathing phases which has potential applications in diagnostic CT imaging and radiotherapy.« less

Self-reported eating rate is associated with weight status in a Dutch population: a validation study and a cross-sectional study.

PubMed

van den Boer, Janet H W; Kranendonk, Jentina; van de Wiel, Anne; Feskens, Edith J M; Geelen, Anouk; Mars, Monica

2017-09-08

Observational studies performed in Asian populations suggest that eating rate is related to BMI. This paper investigates the association between self-reported eating rate (SRER) and body mass index (BMI) in a Dutch population, after having validated SRER against actual eating rate. Two studies were performed; a validation and a cross-sectional study. In the validation study SRER (i.e., 'slow', 'average', or 'fast') was obtained from 57 participants (men/women = 16/41, age: mean ± SD = 22.6 ± 2.8 yrs., BMI: mean ± SD = 22.1 ± 2.8 kg/m 2 ) and in these participants actual eating rate was measured for three food products. Using analysis of variance the association between SRER and actual eating rate was studied. The association between SRER and BMI was investigated in cross-sectional data from the NQplus cohort (i.e., 1473 Dutch adults; men/women = 741/732, age: mean ± SD = 54.6 ± 11.7 yrs., BMI: mean ± SD = 25.9 ± 4.0 kg/m 2 ) using (multiple) linear regression analysis. In the validation study actual eating rate increased proportionally with SRER (for all three food products P < 0.01). In the cross-sectional study SRER was positively associated with BMI in both men and women (P = 0.03 and P < 0.001, respectively). Self-reported fast-eating women had a 1.13 kg/m 2 (95% CI 0.43, 1.84) higher BMI compared to average-speed-eating women, after adjusting for confounders. This was not the case in men; self-reported fast-eating men had a 0.29 kg/m 2 (95% CI -0.22, 0.80) higher BMI compared to average-speed-eating men, after adjusting for confounders. These studies show that self-reported eating rate reflects actual eating rate on a group-level, and that a high self-reported eating rate is associated with a higher BMI in this Dutch population.

In-Line Ultrasonic Monitoring for Sediments Stuck on Inner Wall of a Polyvinyl Chloride Pipe

PubMed Central

2014-01-01

This research verified the applicability and effectiveness of the ultrasonic monitoring of sediments stuck on the inner wall of polyvinyl chloride (PVC) pipes. For identifying the transmittance of acoustic energy and the speed of sound in the PVC material, the pulse-echo ultrasonic testing was conducted for PVC sheets of different thicknesses. To simulate the solidified sediment, the hot melt adhesive (HMA) was covered on the inner wall of the PVC pipe in different heights. From the experiment, the speeds of sound in the PVC and the HMA materials were obtained as about 2258 and 2000 m/s, respectively. The thickness of the materials was calculated through the signal processing such as taking the absolute value and low pass filtering, the echo detection, and the measurement of the time of flight. The errors between actual and measured thicknesses of PVC sheets were below 5%. In the case of the substance stuck on the inner wall, the errors were below 2.5%. Since the pulse-echo ultrasonic inspection is available on the outer surface and its measurement accuracy was over 95%, it can be an efficient and effective in-service structural health monitoring for the sediment on the wall of PVC pipes. PMID:25243223

Ultrasonic wave based pressure measurement in small diameter pipeline.

PubMed

Wang, Dan; Song, Zhengxiang; Wu, Yuan; Jiang, Yuan

2015-12-01

An effective non-intrusive method of ultrasound-based technique that allows monitoring liquid pressure in small diameter pipeline (less than 10mm) is presented in this paper. Ultrasonic wave could penetrate medium, through the acquisition of representative information from the echoes, properties of medium can be reflected. This pressure measurement is difficult due to that echoes' information is not easy to obtain in small diameter pipeline. The proposed method is a study on pipeline with Kneser liquid and is based on the principle that the transmission speed of ultrasonic wave in pipeline liquid correlates with liquid pressure and transmission speed of ultrasonic wave in pipeline liquid is reflected through ultrasonic propagation time providing that acoustic distance is fixed. Therefore, variation of ultrasonic propagation time can reflect variation of pressure in pipeline. Ultrasonic propagation time is obtained by electric processing approach and is accurately measured to nanosecond through high resolution time measurement module. We used ultrasonic propagation time difference to reflect actual pressure in this paper to reduce the environmental influences. The corresponding pressure values are finally obtained by acquiring the relationship between variation of ultrasonic propagation time difference and pressure with the use of neural network analysis method, the results show that this method is accurate and can be used in practice. Copyright © 2015 Elsevier B.V. All rights reserved.

Hierarchical neural network model of the visual system determining figure/ground relation

NASA Astrophysics Data System (ADS)

Kikuchi, Masayuki

2017-07-01

One of the most important functions of the visual perception in the brain is figure/ground interpretation from input images. Figural region in 2D image corresponding to object in 3D space are distinguished from background region extended behind the object. Previously the author proposed a neural network model of figure/ground separation constructed on the standpoint that local geometric features such as curvatures and outer angles at corners are extracted and propagated along input contour in a single layer network (Kikuchi & Akashi, 2001). However, such a processing principle has the defect that signal propagation requires manyiterations despite the fact that actual visual system determines figure/ground relation within the short period (Zhou et al., 2000). In order to attain speed-up for determining figure/ground, this study incorporates hierarchical architecture into the previous model. This study confirmed the effect of the hierarchization as for the computation time by simulation. As the number of layers increased, the required computation time reduced. However, such speed-up effect was saturatedas the layers increased to some extent. This study attempted to explain this saturation effect by the notion of average distance between vertices in the area of complex network, and succeeded to mimic the saturation effect by computer simulation.

Development and evaluation of a mass media Theory of Planned Behaviour intervention to reduce speeding.

PubMed

Stead, Martine; Tagg, Stephen; MacKintosh, Anne Marie; Eadie, Douglas

2005-02-01

The Theory of Planned Behaviour (TPB) has been widely applied to the explanation of health and social behaviours. However, despite its potential to inform behaviour change efforts, there have been surprisingly few attempts to use the TPB to design actual interventions. In 1998, the Scottish Road Safety Campaign implemented a 3-year mass media campaign to reduce speeding on Scotland's roads which was explicitly shaped by the TPB's three main predictors: Attitude, Subjective Norms and Perceived Behavioural Control. A 4-year longitudinal cohort study examined the impact of the campaign on communications outcomes and on TPB constructs. Overall, empirical support was found for the decision to use TPB as the theoretical underpinning of the advertising. The advertising was effective in triggering desired communications outcomes, and was associated with significant changes in attitudes and affective beliefs about speeding. In conclusion, future directions for road safety advertising and for TPB research are discussed.

Fuel conservation evaluation of US (United States) Army helicopters. Part 4. OH-58C flight testing. Final report 22 Sep 20-Nov 82

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belte, D.; Stratton, M.V.

1982-08-01

The United States Army Aviation Engineering Flight Activity conducted level flight performance tests of the OH-58C helicopter at Edwards AFB, California from 22 September to 20 November 1981, and at St. Paul, Minnesota, from 12 January to 9 February 1982. Nondimensional methods were used to identify effects of compressibility and blade stall on performance, and increased referred rotor speeds were used to supplement the range of currently available level flight data. Maximum differences in nondimensional power required attributed to compressibility effects varied from 6.5 to 11%. However, high actual rotor speed at a given condition can result in less powermore » required than at low rotor speed even with the compressibility penalty. The power required characteristics determined by these tests can be combined with engine performance to determine the most fuel efficient operating conditions.« less

Parametric study on laminar flow for finite wings at supersonic speeds

NASA Technical Reports Server (NTRS)

Garcia, Joseph Avila

1994-01-01

Laminar flow control has been identified as a key element in the development of the next generation of High Speed Transports. Extending the amount of laminar flow over an aircraft will increase range, payload, and altitude capabilities as well as lower fuel requirements, skin temperature, and therefore the overall cost. A parametric study to predict the extent of laminar flow for finite wings at supersonic speeds was conducted using a computational fluid dynamics (CFD) code coupled with a boundary layer stability code. The parameters investigated in this study were Reynolds number, angle of attack, and sweep. The results showed that an increase in angle of attack for specific Reynolds numbers can actually delay transition. Therefore, higher lift capability, caused by the increased angle of attack, as well as a reduction in viscous drag, due to the delay in transition, can be expected simultaneously. This results in larger payload and range.

Improving the Response of a Wheel Speed Sensor by Using a RLS Lattice Algorithm

PubMed Central

Hernandez, Wilmar

2006-01-01

Among the complete family of sensors for automotive safety, consumer and industrial application, speed sensors stand out as one of the most important. Actually, speed sensors have the diversity to be used in a broad range of applications. In today's automotive industry, such sensors are used in the antilock braking system, the traction control system and the electronic stability program. Also, typical applications are cam and crank shaft position/speed and wheel and turbo shaft speed measurement. In addition, they are used to control a variety of functions, including fuel injection, ignition timing in engines, and so on. However, some types of speed sensors cannot respond to very low speeds for different reasons. What is more, the main reason why such sensors are not good at detecting very low speeds is that they are more susceptible to noise when the speed of the target is low. In short, they suffer from noise and generally only work at medium to high speeds. This is one of the drawbacks of the inductive (magnetic reluctance) speed sensors and is the case under study. Furthermore, there are other speed sensors like the differential Hall Effect sensors that are relatively immune to interference and noise, but they cannot detect static fields. This limits their operations to speeds which give a switching frequency greater than a minimum operating frequency. In short, this research is focused on improving the performance of a variable reluctance speed sensor placed in a car under performance tests by using a recursive least-squares (RLS) lattice algorithm. Such an algorithm is situated in an adaptive noise canceller and carries out an optimal estimation of the relevant signal coming from the sensor, which is buried in a broad-band noise background where we have little knowledge of the noise characteristics. The experimental results are satisfactory and show a significant improvement in the signal-to-noise ratio at the system output.

Small Acute Benefits of 4 Weeks Processing Speed Training Games on Processing Speed and Inhibition Performance and Depressive Mood in the Healthy Elderly People: Evidence from a Randomized Control Trial

PubMed Central

Nouchi, Rui; Saito, Toshiki; Nouchi, Haruka; Kawashima, Ryuta

2016-01-01

Background: Processing speed training using a 1-year intervention period improves cognitive functions and emotional states of elderly people. Nevertheless, it remains unclear whether short-term processing speed training such as 4 weeks can benefit elderly people. This study was designed to investigate effects of 4 weeks of processing speed training on cognitive functions and emotional states of elderly people. Methods: We used a single-blinded randomized control trial (RCT). Seventy-two older adults were assigned randomly to two groups: a processing speed training game (PSTG) group and knowledge quiz training game (KQTG) group, an active control group. In PSTG, participants were asked to play PSTG (12 processing speed games) for 15 min, during five sessions per week, for 4 weeks. In the KQTG group, participants were asked to play KQTG (four knowledge quizzes) for 15 min, during five sessions per week, for 4 weeks. We measured several cognitive functions and emotional states before and after the 4 week intervention period. Results: Our results revealed that PSTG improved performances in processing speed and inhibition compared to KQTG, but did not improve performance in reasoning, shifting, short term/working memory, and episodic memory. Moreover, PSTG reduced the depressive mood score as measured by the Profile of Mood State compared to KQTG during the 4 week intervention period, but did not change other emotional measures. Discussion: This RCT first provided scientific evidence related to small acute benefits of 4 week PSTG on processing speed, inhibition, and depressive mood in healthy elderly people. We discuss possible mechanisms for improvements in processing speed and inhibition and reduction of the depressive mood. Trial registration: This trial was registered in The University Hospital Medical Information Network Clinical Trials Registry (UMIN000022250). PMID:28066229

Small Acute Benefits of 4 Weeks Processing Speed Training Games on Processing Speed and Inhibition Performance and Depressive Mood in the Healthy Elderly People: Evidence from a Randomized Control Trial.

PubMed

Nouchi, Rui; Saito, Toshiki; Nouchi, Haruka; Kawashima, Ryuta

2016-01-01

Background: Processing speed training using a 1-year intervention period improves cognitive functions and emotional states of elderly people. Nevertheless, it remains unclear whether short-term processing speed training such as 4 weeks can benefit elderly people. This study was designed to investigate effects of 4 weeks of processing speed training on cognitive functions and emotional states of elderly people. Methods: We used a single-blinded randomized control trial (RCT). Seventy-two older adults were assigned randomly to two groups: a processing speed training game (PSTG) group and knowledge quiz training game (KQTG) group, an active control group. In PSTG, participants were asked to play PSTG (12 processing speed games) for 15 min, during five sessions per week, for 4 weeks. In the KQTG group, participants were asked to play KQTG (four knowledge quizzes) for 15 min, during five sessions per week, for 4 weeks. We measured several cognitive functions and emotional states before and after the 4 week intervention period. Results: Our results revealed that PSTG improved performances in processing speed and inhibition compared to KQTG, but did not improve performance in reasoning, shifting, short term/working memory, and episodic memory. Moreover, PSTG reduced the depressive mood score as measured by the Profile of Mood State compared to KQTG during the 4 week intervention period, but did not change other emotional measures. Discussion: This RCT first provided scientific evidence related to small acute benefits of 4 week PSTG on processing speed, inhibition, and depressive mood in healthy elderly people. We discuss possible mechanisms for improvements in processing speed and inhibition and reduction of the depressive mood. Trial registration: This trial was registered in The University Hospital Medical Information Network Clinical Trials Registry (UMIN000022250).

A Latent Variables Examination of Processing Speed, Response Inhibition, and Working Memory during Typical Development

PubMed Central

McAuley, Tara; White, Desirée

2010-01-01

The present study addressed three related aims: (1) to replicate and extend previous work regarding the non-unitary nature of processing speed, response inhibition, and working memory during development, (2) to quantify the rate at which processing speed, response inhibition, and working memory develop and the extent to which the development of these latter abilities reflect general changes in processing speed, and (3) to evaluate whether commonly used tasks of processing speed, response inhibition, and working memory are valid and reliable when used with a developmentally diverse group. To address these aims, a latent variables approach was used to analyze data from 147 participants 6 to 24 years of age. Results showed that processing speed, response inhibition, and working memory were separable abilities and that the extent of this separability was stable cross the age range of participants. All three constructs improved as a function of age; however, only the effect of age on working memory remained significant after processing speed was controlled. The psychometric properties of tasks used to assess the constructs were age invariant, thus validating their use in studies of executive development. PMID:20888572

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

NASA Astrophysics Data System (ADS)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

Perceived Submaximal Force Production in Young Adults

ERIC Educational Resources Information Center

Jackson, Allen W.; Ludtke, Andrew W.; Martin, Scott B.; Koziris, L. (Perry); Dishman, Rod K.

2006-01-01

The purpose of this investigation was to examine the force production patterns using perceived stimulus cues from 10% to 90% of maximal force. In Experiment 1, 54 men (age: 19-34 years) and 53 women (age: 18-37 years) performed leg extensions on a dynamometer at a speed of 60 degrees/s. Participants produced actual forces perceived to be 10-90% of…

IPS analysis on relationship among velocity, density and temperature of the solar wind

NASA Astrophysics Data System (ADS)

Hayashi, K.; Tokumaru, M.; Fujiki, K.

2015-12-01

The IPS(Interplanetary Scintillation)-MHD(magnetohydrodynamics) tomography is a method we have developed to determine three-dimensional MHD solution of the solar wind that best matches the line-of-sight IPS solar-wind speed data (Hayashi et al., 2003). The tomographic approach is an iteration method in which IPS observations are simulated in MHD steady-state solution, then differences between the simulated observation and the actual IPS observation is reduced by modifying solar-wind boundary map at 50 solar radii. This forward model needs to assume solar wind density and temperature as function of speed. We use empirical functions, N(V) and T(V), derived from Helios in-situ measurement data within 0.5 AU in 1970s. For recent years, especially after 2006, these functions yield higher densities and lower temperatures than in-situ measurements indicate. To characterize the differences between the simulated and actual solar wind plasma, we tune parameters in the functions so that agreements with in-situ data (near the Earth and at Ulysses) will be optimized. This optimization approach can help better simulations of the solar corona and heliosphere, and will help our understandings on roles of magnetic field in solar wind heating and acceleration.

The Rivers of the Mississippi Watershed

NASA Image and Video Library

2017-12-08

The Mississippi Watershed is the largest drainage basin in North America at 3.2 million square kilometers in area. The USGS has created a database of this area which indicates the direction of waterflow at each point. By assembling these directions into streamflows, it is possible to trace the path of water from every point of the area to the mouth of the Mississippi in the Gulf of Mexico. This animation starts with the points furthest from the Gulf and reveals the streams and rivers as a steady progression towards the mouth of the Mississippi until all the major rivers are revealed. The speed of the reveal of the rivers is not dependent on the actual speed of the water flow. The reveal proceeds at a constant velocity along each river path, timed so that all reveals reach the mouth of the Mississippi at the same time. This animation does not show actual flow rates of the rivers. All rivers are shown with identical rates. The river colors and widths correspond to the relative lengths of river segments. Credit: NASA's Scientific Visualization Studio/Horace Mitchell Go here to download this video: svs.gsfc.nasa.gov/4493

Direct adaptive performance optimization of subsonic transports: A periodic perturbation technique

NASA Technical Reports Server (NTRS)

Espana, Martin D.; Gilyard, Glenn

1995-01-01

Aircraft performance can be optimized at the flight condition by using available redundancy among actuators. Effective use of this potential allows improved performance beyond limits imposed by design compromises. Optimization based on nominal models does not result in the best performance of the actual aircraft at the actual flight condition. An adaptive algorithm for optimizing performance parameters, such as speed or fuel flow, in flight based exclusively on flight data is proposed. The algorithm is inherently insensitive to model inaccuracies and measurement noise and biases and can optimize several decision variables at the same time. An adaptive constraint controller integrated into the algorithm regulates the optimization constraints, such as altitude or speed, without requiring and prior knowledge of the autopilot design. The algorithm has a modular structure which allows easy incorporation (or removal) of optimization constraints or decision variables to the optimization problem. An important part of the contribution is the development of analytical tools enabling convergence analysis of the algorithm and the establishment of simple design rules. The fuel-flow minimization and velocity maximization modes of the algorithm are demonstrated on the NASA Dryden B-720 nonlinear flight simulator for the single- and multi-effector optimization cases.

Comparative analysis of operational forecasts versus actual weather conditions in airline flight planning, volume 3

NASA Technical Reports Server (NTRS)

Keitz, J. F.

1982-01-01

The impact of more timely and accurate weather data on airline flight planning with the emphasis on fuel savings is studied. This volume of the report discusses the results of Task 3 of the four major tasks included in the study. Task 3 compares flight plans developed on the Suitland forecast with actual data observed by the aircraft (and averaged over 10 degree segments). The results show that the average difference between the forecast and observed wind speed is 9 kts. without considering direction, and the average difference in the component of the forecast wind parallel to the direction of the observed wind is 13 kts. - both indicating that the Suitland forecast underestimates the wind speeds. The Root Mean Square (RMS) vector error is 30.1 kts. The average absolute difference in direction between the forecast and observed wind is 26 degrees and the temperature difference is 3 degree Centigrade. These results indicate that the forecast model as well as the verifying analysis used to develop comparison flight plans in Tasks 1 and 2 is a limiting factor and that the average potential fuel savings or penalty are up to 3.6 percent depending on the direction of flight.

Design of PID temperature control system based on STM32

NASA Astrophysics Data System (ADS)

Zhang, Jianxin; Li, Hailin; Ma, Kai; Xue, Liang; Han, Bianhua; Dong, Yuemeng; Tan, Yue; Gu, Chengru

2018-03-01

A rapid and high-accuracy temperature control system was designed using proportional-integral-derivative (PID) control algorithm with STM32 as micro-controller unit (MCU). The temperature control system can be applied in the fields which have high requirements on the response speed and accuracy of temperature control. The temperature acquisition circuit in system adopted Pt1000 resistance thermometer as temperature sensor. Through this acquisition circuit, the monitoring actual temperature signal could be converted into voltage signal and transmitted into MCU. A TLP521-1 photoelectric coupler was matched with BD237 power transistor to drive the thermoelectric cooler (TEC) in FTA951 module. The effective electric power of TEC was controlled by the pulse width modulation (PWM) signals which generated by MCU. The PWM signal parameters could be adjusted timely by PID algorithm according to the difference between monitoring actual temperature and set temperature. The upper computer was used to input the set temperature and monitor the system running state via serial port. The application experiment results show that the temperature control system is featured by simple structure, rapid response speed, good stability and high temperature control accuracy with the error less than ±0.5°C.

Motor demands impact speed of information processing in Autism Spectrum Disorders

PubMed Central

Kenworthy, Lauren; Yerys, Benjamin E.; Weinblatt, Rachel; Abrams, Danielle N.; Wallace, Gregory L.

2015-01-01

Objective The apparent contradiction between preserved or even enhanced perceptual processing speed on inspection time tasks in autism spectrum disorders (ASD) and impaired performance on complex processing speed tasks that require motor output (e.g. Wechsler Processing Speed Index) has not yet been systematically investigated. This study investigates whether adding motor output demands to an inspection time task impairs ASD performance compared to that of typically developing control (TDC) children. Method The performance of children with ASD (n=28; mean FSIQ=115) and TDC (n=25; mean FSIQ=122) children was compared on processing speed tasks with increasing motor demand. Correlations were run between ASD task performance and Autism Diagnostic Observation Schedule (ADOS) Communication scores. Results Performance by the ASD and TDC groups on a simple perceptual processing speed task with minimal motor demand was equivalent, though it diverged (ASD worse than TDC) on two tasks with the same stimuli, but increased motor output demands. ASD performance on the moderate but not the high speeded motor output demand task was negatively correlated with ADOS communication symptoms. Conclusions These data address the apparent contradiction between preserved inspection time in the context of slowed “processing speed” in ASD. They show that processing speed is preserved when motor demands are minimized, but that increased motor output demands interfere with the ability to act on perceptual processing of simple stimuli. Reducing motor demands (e.g. through the use of computers) may increase the capacity of people with ASD to demonstrate good perceptual processing in a variety of educational, vocational and social settings. PMID:23937483

Mapping the developmental constraints on working memory span performance.

PubMed

Bayliss, Donna M; Jarrold, Christopher; Baddeley, Alan D; Gunn, Deborah M; Leigh, Eleanor

2005-07-01

This study investigated the constraints underlying developmental improvements in complex working memory span performance among 120 children of between 6 and 10 years of age. Independent measures of processing efficiency, storage capacity, rehearsal speed, and basic speed of processing were assessed to determine their contribution to age-related variance in complex span. Results showed that developmental improvements in complex span were driven by 2 age-related but separable factors: 1 associated with general speed of processing and 1 associated with storage ability. In addition, there was an age-related contribution shared between working memory, processing speed, and storage ability that was important for higher level cognition. These results pose a challenge for models of complex span performance that emphasize the importance of processing speed alone.

[Effects of wind speed on drying processes of fuelbeds composed of Mongolian oak broad-leaves.

PubMed

Zhang, Li Bin; Sun, Ping; Jin, Sen

2016-11-18

Water desorption processes of fuel beds with Mongolian oak broad-leaves were observed under conditions with various wind speeds but nearly constant air temperature and humidity. The effects of wind speed on drying coefficients of fuel beds with various moisture contents were analyzed. Three phases of drying process, namely high initial moisture content (>75%) of phase 1, transition state of phase 2, and equilibrium phase III could be identified. During phase 1, water loss rate under higher wind speed was higher than that under lower wind speed. Water loss rate under higher wind speed was lower than that under lower wind speed during phase 2. During phase 3, water loss rates under different wind speeds were similar. The wind effects decreased with the decrease of fuel moisture. The drying coefficient of the Mongolian oak broad-leaves fuel beds was affected by wind speed and fuel bed compactness, and the interaction between these two factors. The coefficient increased with wind speed roughly in a monotonic cubic polynomial form.

Apathy and Reduced Speed of Processing Underlie Decline in Verbal Fluency following DBS

PubMed Central

Foltynie, Tom; Zrinzo, Ludvic; Hyam, Jonathan A.; Limousin, Patricia

2017-01-01

Objective. Reduced verbal fluency is a strikingly uniform finding following deep brain stimulation (DBS) for Parkinson's disease (PD). The precise cognitive mechanism underlying this reduction remains unclear, but theories have suggested reduced motivation, linguistic skill, and/or executive function. It is of note, however, that previous reports have failed to consider the potential role of any changes in speed of processing. Thus, the aim of this study was to examine verbal fluency changes with a particular focus on the role of cognitive speed. Method. In this study, 28 patients with PD completed measures of verbal fluency, motivation, language, executive functioning, and speed of processing, before and after DBS. Results. As expected, there was a marked decline in verbal fluency but also in a timed test of executive functions and two measures of speed of processing. Verbal fluency decline was associated with markers of linguistic and executive functioning, but not after speed of processing was statistically controlled for. In contrast, greater decline in verbal fluency was associated with higher levels of apathy at baseline, which was not associated with changes in cognitive speed. Discussion. Reduced generativity and processing speed may account for the marked reduction in verbal fluency commonly observed following DBS. PMID:28408788

Role of processing speed and depressed mood on encoding, storage, and retrieval memory functions in patients diagnosed with schizophrenia.

PubMed

Brébion, Gildas; David, Anthony S; Bressan, Rodrigo A; Pilowsky, Lyn S

2007-01-01

The role of various types of slowing of processing speed, as well as the role of depressed mood, on each stage of verbal memory functioning in patients diagnosed with schizophrenia was investigated. Mixed lists of high- and low-frequency words were presented, and immediate and delayed free recall and recognition were required. Two levels of encoding were studied by contrasting the relatively automatic encoding of the high-frequency words and the more effortful encoding of the low-frequency words. Storage was studied by contrasting immediate and delayed recall. Retrieval was studied by contrasting free recall and recognition. Three tests of motor and cognitive processing speed were administered as well. Regression analyses involving the three processing speed measures revealed that cognitive speed was the only predictor of the recall and recognition of the low-frequency words. Furthermore, slowing in cognitive speed accounted for the deficit in recall and recognition of the low-frequency words relative to a healthy control group. Depressed mood was significantly associated with recognition of the low-frequency words. Neither processing speed nor depressed mood was associated with storage efficiency. It is concluded that both cognitive speed slowing and depressed mood impact on effortful encoding processes.

Numerical Simulations of High-Speed Chemically Reacting Flow

NASA Technical Reports Server (NTRS)

Ton, V. T.; Karagozian, A. R.; Marble, F. E.; Osher, S. J.; Engquist, B. E.

1994-01-01

The essentially nonoscillatory (ENO) shock-capturing scheme for the solution of hyperbolic equations is extended to solve a system of coupled conservation equations governing two-dimensional, time-dependent, compressible chemically reacting flow with full chemistry. The thermodynamic properties of the mixture are modeled accurately, and stiff kinetic terms are separated from the fluid motion by a fractional step algorithm. The methodology is used to study the concept of shock-induced mixing and combustion, a process by which the interaction of a shock wave with a jet of low-density hydrogen fuel enhances mixing through streamwise vorticity generation. Test cases with and without chemical reaction are explored here. Our results indicate that, in the temperature range examined, vorticity generation as well as the distribution of atomic species do not change significantly with the introduction of a chemical reaction and subsequent heat release. The actual diffusion of hydrogen is also relatively unaffected by the reaction process. This suggests that the fluid mechanics of this problem may be successfully decoupled from the combustion processes, and that computation of the mixing problem (without combustion chemistry) can elucidate much of the important physical features of the flow.

Numerical Simulations of High-Speed Chemically Reacting Flow

NASA Technical Reports Server (NTRS)

Ton, V. T.; Karagozin, A. R.; Marble, F. E.; Osher, S. J.; Engquist, B. E.

1994-01-01

The Essentially NonOscillatory (ENO) shock-capturing scheme for the solution of hyperbolic equations is extended to solve a system of coupled conservation equations governing two-dimensional, time-dependent, compressible chemically reacting flow with full chemistry. The thermodynamic properties of the mixture are modeled accurately, and stiff kinetic terms are separated from the fluid motion by a fractional step algorithm. The methodology is used to study the concept of shock-induced mixing and combustion, a process by which the interaction of a shock wave with a jet of low-density hydrogen fuel enhances mixing through streamwise vorticity generation. Test cases with and without chemical reaction are explored here. Our results indicate that, in the temperature range examined, vorticity generation as well as the distribution of atomic species do not change significantly with the introduction of a chemical reaction and subsequent heat release. The actual diffusion of hydrogen is also relatively unaffected by the reaction process. This suggests that the fluid mechanics of this problem may be successfully decoupled from the combustion processes, and that computation of the mixing problem (without combustion chemistry) can elucidate much of the important physical features of the flow.

Research and design on orthogonal diffraction grating-based 3D nanometer displacement sensor

NASA Astrophysics Data System (ADS)

Liu, Baoshuai; Yuan, Yibao; Yin, Zhehao

2017-10-01

This study concerns an orthogonal diffraction grating-based nanometer displacement sensor. In this study, we performed calculation of displacements in the XYZ directions. In the optical measured path part, we used a two-dimensional orthogonal motion grating and a two-dimensional orthogonal reference grating with the pitch of 0.5um to measure the displacement of XYZ in three directions by detecting ±1st diffraction fringes. The self-collimated structure of the grating greatly extended the Z-axis range. We also simulated the optical path of the sensor with ZEMAX software and verified the feasibility of the scheme. For signal subdivision and processing, we combined large number counting (completed grating line) with small number counting (digital subdivision), realizing high multiples of subdivision of grating interference signals. We used PC to process the interference fringes and greatly improved the processing speed. In the scheme, the theoretical multiples of subdivision could reach 1024 with 10-bit AD conversion, but the actual multiples of subdivision was limited by the quality of the grating interference signals. So we introduced an orthogonal compensation circuit and a filter circuit to improve the signal quality.

Bilingual processing of ASL-English code-blends: The consequences of accessing two lexical representations simultaneously

PubMed Central

Emmorey, Karen; Petrich, Jennifer; Gollan, Tamar H.

2012-01-01

Bilinguals who are fluent in American Sign Language (ASL) and English often produce code-blends - simultaneously articulating a sign and a word while conversing with other ASL-English bilinguals. To investigate the cognitive mechanisms underlying code-blend processing, we compared picture-naming times (Experiment 1) and semantic categorization times (Experiment 2) for code-blends versus ASL signs and English words produced alone. In production, code-blending did not slow lexical retrieval for ASL and actually facilitated access to low-frequency signs. However, code-blending delayed speech production because bimodal bilinguals synchronized English and ASL lexical onsets. In comprehension, code-blending speeded access to both languages. Bimodal bilinguals’ ability to produce code-blends without any cost to ASL implies that the language system either has (or can develop) a mechanism for switching off competition to allow simultaneous production of close competitors. Code-blend facilitation effects during comprehension likely reflect cross-linguistic (and cross-modal) integration at the phonological and/or semantic levels. The absence of any consistent processing costs for code-blending illustrates a surprising limitation on dual-task costs and may explain why bimodal bilinguals code-blend more often than they code-switch. PMID:22773886

The performance and application of high speed long life LH2 hybrid bearings for reusable rocket engine turbomachinery

NASA Technical Reports Server (NTRS)

Hannum, N. P.; Nielson, C. E.

1983-01-01

Data are presented for two different experimental programs which were conducted to investigate the characteristics of a hybrid (hydrostatic/ball) bearing operating in liquid hydrogen. The same bearing design was used in both programs. Analytical predictions were made of the bearing characteristics and are compared with the experimental results when possible. The first program used a bearing tester to determine the steady state, transient, and cyclic life characteristics of the bearing over a wide range of operating conditions. The second program demonstrated the feasibility of applying hybrid bearings to an actual high speed turbopump by retrofitting and then testing an existing liquid hydrogen turbopump with the bearings.

Multiple attractors and critical parameters and how to find them numerically: the right, the wrong and the gambling way

NASA Astrophysics Data System (ADS)

True, Hans

2013-03-01

In recent years, several authors have proposed 'easier numerical methods' to find the critical speed in railway dynamical problems. Actually, the methods do function in some cases, but in most cases it is really a gamble. In this article, the methods are discussed and the pros and contras are commented upon. I also address the questions when a linearisation is allowed and the curious fact that the hunting motion is more robust than the ideal stationary-state motion on the track. Concepts such as 'multiple attractors', 'subcritical and supercritical bifurcations', 'permitted linearisation', 'the danger of running at supercritical speeds' and 'chaotic motion' are addressed.

New generation of free-piston shock tunnels

NASA Technical Reports Server (NTRS)

Morrison, W. R. B.; Stalker, R. J.; Duffin, J.

1990-01-01

Consideration is given to three free-piston driven hypersonic tunnels under construction that will greatly enhance existing test capabilities. The tunnel being built at Caltech will feature energy capabilities about 40 percent higher than those of the world's largest operational free-piston tunnel to date. The second tunnel under construction will allow full-size engine hardware at near-orbital speeds. The third facility is a high-performance expansion tube that will be capable of generating high enthalpy flows at speeds of up to 9 km/sec. It will provide flows with dissociation levels much lower than are attainable with a reflected shock tunnel, approaching actual flight conditions. A table shows the tunnels' characteristics.

Physio-Environmental Sensing and Live Modeling

PubMed Central

Diaz, Vanessa; Gaggioli, Andrea; Liò, Pietro; Mazzà, Claudia; Merelli, Emanuela; Meskers, Carel G.M; Pappalardo, Francesco; von Ammon, Rainer

2013-01-01

In daily life, humans are constantly interacting with their environment. Evidence is emerging that this interaction is a very important modulator of health and well-being, even more so in our rapidly ageing society. Information and communication technology lies at the heart of the human health care revolution. It cannot remain acceptable to use out of date data analysis and predictive algorithms when superior alternatives exist. Communication network speed, high penetration of home broadband, availability of various mobile network options, together with the available detailed biological data for individuals, are producing promising advances in computerized systems that will turn information on human-environment interactions into actual knowledge with the potential to help make medical and lifestyle decisions. We introduced and discussed a key scenario in which hardware and software technologies capable of simultaneously sensing physiological and environmental signals process health care data in real-time to issue alarms, warnings, or simple recommendations to the patient or carers. PMID:23612245

ISTP SBIR phase 1 Full-Sky Scanner: A feasibility study

NASA Technical Reports Server (NTRS)

1986-01-01

The objective was to develop a Full-Sky Sensor (FSS) to detect the Earth, Sun and Moon from a spinning spacecraft. The concept adopted has infinitely variable resolution. A high-speed search mode is implemented on the spacecraft. The advantages are: (1) a single sensor determines attitude parameters from Earth, Sun and Moon, thus eliminating instrument mounting errors; (2) the bias between the actual spacecraft spin axis and the intended spin axis can be determined; (3) cost is minimized; and (4) ground processing is straightforward. The FSS is a modification of an existing flight-proven sensor. Modifications to the electronics are necessary to accommodate the amplitude range and signal width range of the celestial bodies to be detected. Potential applications include ISTP missions, Multi-Spacecraft Satellite Program (MSSP), dual-spin spacecraft at any altitude, spinning spacecraft at any altitude, and orbit parameter determination for low-Earth orbits.

Accuracy and speed of orthographic processing in persons with developmental dyslexia.

PubMed

King, Wayne M; Lombardino, Linda L; Ahmed, Sarah

2005-08-01

A group of 39 persons (20 male and 19 female, 11.0 to 32.5 yr.) with developmental dyslexia and 42 controls (21 male and 21 female, 11.2 to 32.3 years) were compared on computerized tests of sight word reading, nonword decoding, and spelling recognition. The subjects with developmental dyslexia performed significantly slower and less accurately than controls on all tasks. Further, the effect size of the group differences was larger for the older group. Within-group analyses showed a significant difference by age group on accuracy. Only the control group showed a significant age difference between groups on response time. Mean accuracy and response times for the reading-disabled subjects resembled shifted versions of the control group means. These results agree with previous reports that phonological deficits persist for reading-disabled adults and suggest a test of whether the discrepancy between reading-disabled and typically achieving readers may actually increase across age groups.

Research on flight stability performance of rotor aircraft based on visual servo control method

NASA Astrophysics Data System (ADS)

Yu, Yanan; Chen, Jing

2016-11-01

control method based on visual servo feedback is proposed, which is used to improve the attitude of a quad-rotor aircraft and to enhance its flight stability. Ground target images are obtained by a visual platform fixed on aircraft. Scale invariant feature transform (SIFT) algorism is used to extract image feature information. According to the image characteristic analysis, fast motion estimation is completed and used as an input signal of PID flight control system to realize real-time status adjustment in flight process. Imaging tests and simulation results show that the method proposed acts good performance in terms of flight stability compensation and attitude adjustment. The response speed and control precision meets the requirements of actual use, which is able to reduce or even eliminate the influence of environmental disturbance. So the method proposed has certain research value to solve the problem of aircraft's anti-disturbance.

Very low band gap thiadiazoloquinoxaline donor-acceptor polymers as multi-tool conjugated polymers.

PubMed

Steckler, Timothy T; Henriksson, Patrik; Mollinger, Sonya; Lundin, Angelica; Salleo, Alberto; Andersson, Mats R

2014-01-29

Here we report on the synthesis of two novel very low band gap (VLG) donor-acceptor polymers (Eg ≤ 1 eV) and an oligomer based on the thiadiazoloquinoxaline acceptor. Both polymers demonstrate decent ambipolar mobilities, with P1 showing the best performance of ∼10(-2) cm(2) V(-1) s(-1) for p- and n-type operation. These polymers are among the lowest band gap polymers (≲0.7 eV) reported, with a neutral λmax = 1476 nm (P2), which is the farthest red-shifted λmax reported to date for a soluble processable polymer. Very little has been done to characterize the electrochromic aspects of VLG polymers; interestingly, these polymers actually show a bleaching of their neutral absorptions in the near-infrared region and have an electrochromic contrast up to 30% at a switching speed of 3 s.

An improved genetic algorithm and its application in the TSP problem

NASA Astrophysics Data System (ADS)

Li, Zheng; Qin, Jinlei

2011-12-01

Concept and research actuality of genetic algorithm are introduced in detail in the paper. Under this condition, the simple genetic algorithm and an improved algorithm are described and applied in an example of TSP problem, where the advantage of genetic algorithm is adequately shown in solving the NP-hard problem. In addition, based on partial matching crossover operator, the crossover operator method is improved into extended crossover operator in order to advance the efficiency when solving the TSP. In the extended crossover method, crossover operator can be performed between random positions of two random individuals, which will not be restricted by the position of chromosome. Finally, the nine-city TSP is solved using the improved genetic algorithm with extended crossover method, the efficiency of whose solution process is much higher, besides, the solving speed of the optimal solution is much faster.

Prediction of flow dynamics using point processes

NASA Astrophysics Data System (ADS)

Hirata, Yoshito; Stemler, Thomas; Eroglu, Deniz; Marwan, Norbert

2018-01-01

Describing a time series parsimoniously is the first step to study the underlying dynamics. For a time-discrete system, a generating partition provides a compact description such that a time series and a symbolic sequence are one-to-one. But, for a time-continuous system, such a compact description does not have a solid basis. Here, we propose to describe a time-continuous time series using a local cross section and the times when the orbit crosses the local cross section. We show that if such a series of crossing times and some past observations are given, we can predict the system's dynamics with fine accuracy. This reconstructability neither depends strongly on the size nor the placement of the local cross section if we have a sufficiently long database. We demonstrate the proposed method using the Lorenz model as well as the actual measurement of wind speed.

ISTP SBIR phase 1 Full-Sky Scanner: A feasibility study

NASA Astrophysics Data System (ADS)

1986-08-01

The objective was to develop a Full-Sky Sensor (FSS) to detect the Earth, Sun and Moon from a spinning spacecraft. The concept adopted has infinitely variable resolution. A high-speed search mode is implemented on the spacecraft. The advantages are: (1) a single sensor determines attitude parameters from Earth, Sun and Moon, thus eliminating instrument mounting errors; (2) the bias between the actual spacecraft spin axis and the intended spin axis can be determined; (3) cost is minimized; and (4) ground processing is straightforward. The FSS is a modification of an existing flight-proven sensor. Modifications to the electronics are necessary to accommodate the amplitude range and signal width range of the celestial bodies to be detected. Potential applications include ISTP missions, Multi-Spacecraft Satellite Program (MSSP), dual-spin spacecraft at any altitude, spinning spacecraft at any altitude, and orbit parameter determination for low-Earth orbits.

Do attentional capacities and processing speed mediate the effect of age on executive functioning?

PubMed

Gilsoul, Jessica; Simon, Jessica; Hogge, Michaël; Collette, Fabienne

2018-02-06

The executive processes are well known to decline with age, and similar data also exists for attentional capacities and processing speed. Therefore, we investigated whether these two last nonexecutive variables would mediate the effect of age on executive functions (inhibition, shifting, updating, and dual-task coordination). We administered a large battery of executive, attentional and processing speed tasks to 104 young and 71 older people, and we performed mediation analyses with variables showing a significant age effect. All executive and processing speed measures showed age-related effects while only the visual scanning task performance (selective attention) was explained by age when controlled for gender and educational level. Regarding mediation analyses, visual scanning partially mediated the age effect on updating while processing speed partially mediated the age effect on shifting, updating and dual-task coordination. In a more exploratory way, inhibition was also found to partially mediate the effect of age on the three other executive functions. Attention did not greatly influence executive functioning in aging while, in agreement with the literature, processing speed seems to be a major mediator of the age effect on these processes. Interestingly, the global pattern of results seems also to indicate an influence of inhibition but further studies are needed to confirm the role of that variable as a mediator and its relative importance by comparison with processing speed.

Prediction of half-marathon race time in recreational female and male runners.

PubMed

Knechtle, Beat; Barandun, Ursula; Knechtle, Patrizia; Zingg, Matthias A; Rosemann, Thomas; Rüst, Christoph A

2014-01-01

Half-marathon running is of high popularity. Recent studies tried to find predictor variables for half-marathon race time for recreational female and male runners and to present equations to predict race time. The actual equations included running speed during training for both women and men as training variable but midaxillary skinfold for women and body mass index for men as anthropometric variable. An actual study found that percent body fat and running speed during training sessions were the best predictor variables for half-marathon race times in both women and men. The aim of the present study was to improve the existing equations to predict half-marathon race time in a larger sample of male and female half-marathoners by using percent body fat and running speed during training sessions as predictor variables. In a sample of 147 men and 83 women, multiple linear regression analysis including percent body fat and running speed during training units as independent variables and race time as dependent variable were performed and an equation was evolved to predict half-marathon race time. For men, half-marathon race time might be predicted by the equation (r(2) = 0.42, adjusted r(2) = 0.41, SE = 13.3) half-marathon race time (min) = 142.7 + 1.158 × percent body fat (%) - 5.223 × running speed during training (km/h). The predicted race time correlated highly significantly (r = 0.71, p < 0.0001) to the achieved race time. For women, half-marathon race time might be predicted by the equation (r(2) = 0.68, adjusted r(2) = 0.68, SE = 9.8) race time (min) = 168.7 + 1.077 × percent body fat (%) - 7.556 × running speed during training (km/h). The predicted race time correlated highly significantly (r = 0.89, p < 0.0001) to the achieved race time. The coefficients of determination of the models were slightly higher than for the existing equations. Future studies might include physiological variables to increase the coefficients of determination of the models.

Rotor dynamic behaviour of a high-speed oil-free motor compressor with a rigid coupling supported on four radial magnetic bearings

NASA Technical Reports Server (NTRS)

Schmied, J.; Pradetto, J. C.

1994-01-01

The combination of a high-speed motor, dry gas seals, and magnetic bearings realized in this unit facilitates the elimination of oil. The motor is coupled with a quill shaft to the compressor. This yields higher natural frequencies of the rotor than with the use of a diaphragm coupling and helps to maintain a sufficient margin of the maximum speed to the frequency of the second compressor bending mode. However, the controller of each bearing then has to take the combined modes of both machines into account. The requirements for the controller to ensure stability and sufficient damping of all critical speeds are designed and compared with the implemented controller. The calculated closed loop behavior was confirmed experimentally, except the stability of some higher modes due to slight frequency deviations of the rotor model to the actual rotor. The influence of a mechanical damper as a device to provide additional damping to high models is demonstrated theoretically. After all, it was not necessary to install the damper, since all modes cold be stabilized by the controller.

Indexed semi-Markov process for wind speed modeling.

NASA Astrophysics Data System (ADS)

Petroni, F.; D'Amico, G.; Prattico, F.

2012-04-01

The increasing interest in renewable energy leads scientific research to find a better way to recover most of the available energy. Particularly, the maximum energy recoverable from wind is equal to 59.3% of that available (Betz law) at a specific pitch angle and when the ratio between the wind speed in output and in input is equal to 1/3. The pitch angle is the angle formed between the airfoil of the blade of the wind turbine and the wind direction. Old turbine and a lot of that actually marketed, in fact, have always the same invariant geometry of the airfoil. This causes that wind turbines will work with an efficiency that is lower than 59.3%. New generation wind turbines, instead, have a system to variate the pitch angle by rotating the blades. This system able the wind turbines to recover, at different wind speed, always the maximum energy, working in Betz limit at different speed ratios. A powerful system control of the pitch angle allows the wind turbine to recover better the energy in transient regime. A good stochastic model for wind speed is then needed to help both the optimization of turbine design and to assist the system control to predict the value of the wind speed to positioning the blades quickly and correctly. The possibility to have synthetic data of wind speed is a powerful instrument to assist designer to verify the structures of the wind turbines or to estimate the energy recoverable from a specific site. To generate synthetic data, Markov chains of first or higher order are often used [1,2,3]. In particular in [1] is presented a comparison between a first-order Markov chain and a second-order Markov chain. A similar work, but only for the first-order Markov chain, is conduced by [2], presenting the probability transition matrix and comparing the energy spectral density and autocorrelation of real and synthetic wind speed data. A tentative to modeling and to join speed and direction of wind is presented in [3], by using two models, first-order Markov chain with different number of states, and Weibull distribution. All this model use Markov chains to generate synthetic wind speed time series but the search for a better model is still open. Approaching this issue, we applied new models which are generalization of Markov models. More precisely we applied semi-Markov models to generate synthetic wind speed time series. In a previous work we proposed different semi-Markov models, showing their ability to reproduce the autocorrelation structures of wind speed data. In that paper we showed also that the autocorrelation is higher with respect to the Markov model. Unfortunately this autocorrelation was still too small compared to the empirical one. In order to overcome the problem of low autocorrelation, in this paper we propose an indexed semi-Markov model. More precisely we assume that wind speed is described by a discrete time homogeneous semi-Markov process. We introduce a memory index which takes into account the periods of different wind activities. With this model the statistical characteristics of wind speed are faithfully reproduced. The wind is a very unstable phenomenon characterized by a sequence of lulls and sustained speeds, and a good wind generator must be able to reproduce such sequences. To check the validity of the predictive semi-Markovian model, the persistence of synthetic winds were calculated, then averaged and computed. The model is used to generate synthetic time series for wind speed by means of Monte Carlo simulations and the time lagged autocorrelation is used to compare statistical properties of the proposed models with those of real data and also with a time series generated though a simple Markov chain. [1] A. Shamshad, M.A. Bawadi, W.M.W. Wan Hussin, T.A. Majid, S.A.M. Sanusi, First and second order Markov chain models for synthetic generation of wind speed time series, Energy 30 (2005) 693-708. [2] H. Nfaoui, H. Essiarab, A.A.M. Sayigh, A stochastic Markov chain model for simulating wind speed time series at Tangiers, Morocco, Renewable Energy 29 (2004) 1407-1418. [3] F. Youcef Ettoumi, H. Sauvageot, A.-E.-H. Adane, Statistical bivariate modeling of wind using first-order Markov chain and Weibull distribution, Renewable Energy 28 (2003) 1787-1802.

Time course of word production in fast and slow speakers: a high density ERP topographic study.

PubMed

Laganaro, Marina; Valente, Andrea; Perret, Cyril

2012-02-15

The transformation of an abstract concept into an articulated word is achieved through a series of encoding processes, which time course has been repeatedly investigated in the psycholinguistic and neuroimaging literature on single word production. The estimates of the time course issued from previous investigations represent the timing of process duration for mean processing speed: as production speed varies significantly across speakers, a crucial question is how the timing of encoding processing varies with speed. Here we investigated whether between-subjects variability in the speed of speech production is distributed along all encoding processes or if it is accounted for by a specific processing stage. We analysed event-related electroencephalographical (ERP) correlates during overt picture naming in 45 subjects divided into three speed subgroups according to their production latencies. Production speed modulated waveform amplitudes in the time window ranging from about 200 to 350 ms after picture presentation and the duration of a stable electrophysiological spatial configuration in the same time period. The remaining time windows from picture onset to 200 ms before articulation were unaffected by speed. By contrast, the manipulation of a psycholinguistic variable, word age-of-acquisition, modulated ERPs in all speed subgroups in a different and later time period, starting at around 400 ms after picture presentation, associated with phonological encoding processes. These results indicate that the between-subject variability in the speed of single word production is principally accounted for by the timing of a stable electrophysiological activity in the 200-350 ms time period, presumably associated with lexical selection. Copyright © 2011 Elsevier Inc. All rights reserved.

Detection and assessment of flaws in friction stir welded metallic plates

NASA Astrophysics Data System (ADS)

Fakih, Mohammad Ali; Mustapha, Samir; Tarraf, Jaafar; Ayoub, Georges; Hamade, Ramsey

2017-04-01

Investigated is the ability of ultrasonic guided waves to detect flaws and assess the quality of friction stir welds (FSW). AZ31B magnesium plates were friction stir welded. While process parameters of spindle speed and tool feed were fixed, shoulder penetration depth was varied resulting in welds of varying quality. Ultrasonic waves were excited at different frequencies using piezoelectric wafers and the fundamental symmetric (S0) mode was selected to detect the flaws resulting from the welding process. The front of the first transmitted wave signal was used to capture the S0 mode. A damage index (DI) measure was defined based on the amplitude attenuation after wave interaction with the welded zone. Computed Tomography (CT) scanning was employed as a nondestructive testing (NDT) technique to assess the actual weld quality. Derived DI values were plotted against CT-derived flaw volume resulting in a perfectly linear fit. The proposed approach showed high sensitivity of the S0 mode to internal flaws within the weld. As such, this methodology bears great potential as a future predictive method for the evaluation of FSW weld quality.

Response surface methodology for evaluation and optimization of process parameter and antioxidant capacity of rice flour modified by enzymatic extrusion.

PubMed

Xu, Enbo; Pan, Xiaowei; Wu, Zhengzong; Long, Jie; Li, Jingpeng; Xu, Xueming; Jin, Zhengyu; Jiao, Aiquan

2016-12-01

For the purpose of investigating the effect of enzyme concentration (EC), barrel temperature (BT), moisture content (MC), and screw speed (SS) on processing parameters (product temperature, die pressure and special mechanical energy (SME)) and product responses (extent of gelatinization (GE), retention rate of total phenolic content (TPC-RR)), rice flour extruded with thermostable α-amylase was analyzed by response surface methodology. Stepwise regression models were computed to generate response surface and contour plots, revealing that both TPC-RR and GE increased as increasing MC while expressed different sensitivities to BT during enzymatic extrusion. Phenolics preservation was benefited from low SME. According to multiple-factor optimization, the conditions required to obtain the target SME (10kJ/kg), GE (100%) and TPC-RR (85%) were: EC=1.37‰, BT=93.01°C, MC=44.30%, and SS=171.66rpm, with the actual values (9.49kJ/kg, 99.96% and 87.10%, respectively) showing a good fit to the predicted values. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.

Implementation and characterization of active feed-forward for deterministic linear optics quantum computing

NASA Astrophysics Data System (ADS)

Böhi, P.; Prevedel, R.; Jennewein, T.; Stefanov, A.; Tiefenbacher, F.; Zeilinger, A.

2007-12-01

In general, quantum computer architectures which are based on the dynamical evolution of quantum states, also require the processing of classical information, obtained by measurements of the actual qubits that make up the computer. This classical processing involves fast, active adaptation of subsequent measurements and real-time error correction (feed-forward), so that quantum gates and algorithms can be executed in a deterministic and hence error-free fashion. This is also true in the linear optical regime, where the quantum information is stored in the polarization state of photons. The adaptation of the photon’s polarization can be achieved in a very fast manner by employing electro-optical modulators, which change the polarization of a trespassing photon upon appliance of a high voltage. In this paper we discuss techniques for implementing fast, active feed-forward at the single photon level and we present their application in the context of photonic quantum computing. This includes the working principles and the characterization of the EOMs as well as a description of the switching logics, both of which allow quantum computation at an unprecedented speed.

A low cost imaging displacement measurement system for spacecraft thermal vacuum testing

NASA Technical Reports Server (NTRS)

Dempsey, Brian

2006-01-01

A low cost imaging displacement technique suitable for use in thermal vacuum testing was built and tested during thermal vacuum testing of the space infrared telescope facility (SIRTF, later renamed Spitzer infrared telescope facility). The problem was to measure the relative displacement of different portions of the spacecraft due to thermal expansion or contraction. Standard displacement measuring instrumentation could not be used because of the widely varying temperatures on the spacecraft and for fear of invalidating the thermal vacuum testing. The imaging system was conceived, designed, purchased, and installed in approximately 2 months at very low cost. The system performed beyond expectations proving that sub millimeter displacements could be measured from over 2 meters away. Using commercial optics it was possible to make displacement measurements down to 10 (mu)m. An automated image processing tool was used to process the data, which not only speeded up data reduction, but showed that velocities and accelerations could also be measured. Details of the design and capabilities of the system are discussed along with the results of the test on the observatory. Several images from the actual test are presented.

Present and future trends of laser materials processing in Japan

NASA Astrophysics Data System (ADS)

Matsunawa, Akira

1991-10-01

Lasers quickly penetrated into Japanese industries in the mid-80s. The paper reviews the present situation of industrial lasers and their applications in Japanese industries for materials removal, joining, and some surface modification technologies as well as their economical evaluation compared with competitive technologies. Laser cutting of metallic and nonmetallic thin sheets is widely prevalent even in small scale industries as a flexible manufacturing tool. As for the laser welding is concerned, industrial applications are rather limited in mass production lines. This mainly comes from the fact that the present laser technologies have not employed the adaptive control because of the lack of sensors, monitoring, and control systems which can tolerate the high-precision and high-speed processing. In spite of this situation, laser welding is rapidly increasing in recent years in industries such as automotive, machinery, electric/electronic, steel, heavy industries, etc. Laser surface modification technologies have attracted significant interest from industrial people, but actual application is very limited today. However, the number of R&D papers is increasing year by year. The paper also reviews these new technology trends in Japan.

Self-consistent nonlocal feedback theory for electrocatalytic swimmers with heterogeneous surface chemical kinetics

NASA Astrophysics Data System (ADS)

Nourhani, Amir; Crespi, Vincent H.; Lammert, Paul E.

2015-06-01

We present a self-consistent nonlocal feedback theory for the phoretic propulsion mechanisms of electrocatalytic micromotors or nanomotors. These swimmers, such as bimetallic platinum and gold rods catalyzing decomposition of hydrogen peroxide in aqueous solution, have received considerable theoretical attention. In contrast, the heterogeneous electrochemical processes with nonlocal feedback that are the actual "engines" of such motors are relatively neglected. We present a flexible approach to these processes using bias potential as a control parameter field and a locally-open-circuit reference state, carried through in detail for a spherical motor. While the phenomenological flavor makes meaningful contact with experiment easier, required inputs can also conceivably come from, e.g., Frumkin-Butler-Volmer kinetics. Previously obtained results are recovered in the weak-heterogeneity limit and improved small-basis approximations tailored to structural heterogeneity are presented. Under the assumption of weak inhomogeneity, a scaling form is deduced for motor speed as a function of fuel concentration and swimmer size. We argue that this form should be robust and demonstrate a good fit to experimental data.

Optimizing Research to Speed Up Availability of Pediatric Antiretroviral Drugs and Formulations.

PubMed

Penazzato, Martina; Gnanashanmugam, Devasena; Rojo, Pablo; Lallemant, Marc; Lewis, Linda L; Rocchi, Francesca; Saint Raymond, Agnes; Ford, Nathan; Hazra, Rohan; Giaquinto, Carlo; Belew, Yodit; Gibb, Diana M; Abrams, Elaine J

2017-06-01

Globally 1.8 million children are living with human immunodeficiency virus (HIV), yet only 51% of those eligible actually start treatment. Research and development (R&D) for pediatric antiretrovirals (ARVs) is a lengthy process and lags considerably behind drug development in adults. Providing safe, effective, and well-tolerated drugs for children remains critical to ensuring scale-up globally. We review current approaches to R&D for pediatric ARVs and suggest innovations to enable simplified, faster, and more comprehensive strategies to develop optimal formulations. Several approaches could be adopted, including focusing on a limited number of prioritized formulations and strengthening existing partnerships to ensure that pediatric investigation plans are developed early in the drug development process. Simplified and more efficient mechanisms to undertake R&D need to be put in place, and financing mechanisms must be made more sustainable. Lessons learned from HIV should be shared to support progress in developing pediatric formulations for other diseases, including tuberculosis and viral hepatitis. © The Author 2017. Published by Oxford University Press for the Infectious Diseases Society of America. All rights reserved. For permissions, e-mail: journals.permissions@oup.com.

Process Optimization and Microstructure Characterization of Ti6Al4V Manufactured by Selective Laser Melting

NASA Astrophysics Data System (ADS)

junfeng, Li; zhengying, Wei

2017-11-01

Process optimization and microstructure characterization of Ti6Al4V manufactured by selective laser melting (SLM) were investigated in this article. The relative density of sampled fabricated by SLM is influenced by the main process parameters, including laser power, scan speed and hatch distance. The volume energy density (VED) was defined to account for the combined effect of the main process parameters on the relative density. The results shown that the relative density changed with the change of VED and the optimized process interval is 55˜60J/mm3. Furthermore, compared with laser power, scan speed and hatch distance by taguchi method, it was found that the scan speed had the greatest effect on the relative density. Compared with the microstructure of the cross-section of the specimen at different scanning speeds, it was found that the microstructures at different speeds had similar characteristics, all of them were needle-like martensite distributed in the β matrix, but with the increase of scanning speed, the microstructure is finer and the lower scan speed leads to coarsening of the microstructure.

Naming-Speed Processes, Timing, and Reading: A Conceptual Review.

ERIC Educational Resources Information Center

Wolf, Maryanne; Bowers, Patricia Greig; Biddle, Kathleen

2000-01-01

This article reviews evidence for seven central questions about the role of naming-speed deficits in developmental reading disabilities. Cross-sectional, longitudinal, and cross-linguistic research on naming-speed processes, timing processes, and reading is presented. An evolving model of visual naming illustrates areas of difference and areas of…

Acceleration of integral imaging based incoherent Fourier hologram capture using graphic processing unit.

PubMed

Jeong, Kyeong-Min; Kim, Hee-Seung; Hong, Sung-In; Lee, Sung-Keun; Jo, Na-Young; Kim, Yong-Soo; Lim, Hong-Gi; Park, Jae-Hyeung

2012-10-08

Speed enhancement of integral imaging based incoherent Fourier hologram capture using a graphic processing unit is reported. Integral imaging based method enables exact hologram capture of real-existing three-dimensional objects under regular incoherent illumination. In our implementation, we apply parallel computation scheme using the graphic processing unit, accelerating the processing speed. Using enhanced speed of hologram capture, we also implement a pseudo real-time hologram capture and optical reconstruction system. The overall operation speed is measured to be 1 frame per second.

Attention, processing speed, and executive functioning in pediatric brain tumor survivors treated with proton beam radiation therapy.

PubMed

Antonini, Tanya N; Ris, M Douglas; Grosshans, David R; Mahajan, Anita; Okcu, M Fatih; Chintagumpala, Murali; Paulino, Arnold; Child, Amanda E; Orobio, Jessica; Stancel, Heather H; Kahalley, Lisa S

2017-07-01

This study examines attention, processing speed, and executive functioning in pediatric brain tumor survivors treated with proton beam radiation therapy (PBRT). We examined 39 survivors (age 6-19years) who were 3.61years post-PBRT on average. Craniospinal (CSI; n=21) and focal (n=18) subgroups were analyzed. Attention, processing speed, and executive functioning scores were compared to population norms, and clinical/demographic risk factors were examined. As a group, survivors treated with focal PBRT exhibited attention, processing speed, and executive functioning that did not differ from population norms (all p>0.05). Performance in the CSI group across attention scales was normative (all p>0.05), but areas of relative weakness were identified on one executive functioning subtest and several processing speed subtests (all p<0.01). Survivors treated with PBRT may exhibit relative resilience in cognitive domains traditionally associated with radiation late effects. Attention, processing speed, and executive functioning remained intact and within normal limits for survivors treated with focal PBRT. Among survivors treated with CSI, a score pattern emerged that was suggestive of difficulties in underlying component skills (i.e., processing speed) rather than true executive dysfunction. No evidence of profound cognitive impairment was found in either group. Copyright © 2017 Elsevier B.V. All rights reserved.

Relationships among cognitive deficits and component skills of reading in younger and older students with developmental dyslexia.

PubMed

Park, Heeyoung; Lombardino, Linda J

2013-09-01

Processing speed deficits along with phonological awareness deficits have been identified as risk factors for dyslexia. This study was designed to examine the behavioral profiles of two groups, a younger (6-8 years) and an older (10-15 years) group of dyslexic children for the purposes of (1) evaluating the degree to which phonological awareness and processing speed deficits occur in the two developmental cohorts; (2) determining the strength of relationships between the groups' respective mean scores on cognitive tasks of phonological awareness and processing speed and their scores on component skills of reading; and (3) evaluating the degree to which phonological awareness and processing speed serve as concurrent predictors of component reading skills for each group. The mean scaled scores for both groups were similar on all but one processing speed task. The older group was significantly more depressed on a visual matching test of attention, scanning, and speed. Correlations between reading skills and the cognitive constructs were very similar for both age-groups. Neither of the two phonological awareness tasks correlated with either of the two processing speed tasks or with any of the three measures of reading. One of the two processing speed measures served as a concurrent predictor of word- and text-level reading in the younger, however, only the rapid naming measure functioned as a concurrent predictor of word reading in the older group. Conversely, phonological processing measures did not serve as concurrent predictors for word-level or text-level reading in either of the groups. Descriptive analyses of individual subjects' deficits in the domains of phonological awareness and processing speed revealed that (1) both linguistic and nonlinguistic processing speed deficits in the younger dyslexic children occurred at higher rates than deficits in phonological awareness and (2) cognitive deficits within and across these two domains were greater in the older dyslexic children. Our findings underscore the importance of using rapid naming measures when testing school-age children suspected of having a reading disability and suggest that processing speed measures that do not reply on verbal responses may serve as predictors of reading disability in young children prior to their development of naming automaticity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Thermomechanical simulations and experimental validation for high speed incremental forming

NASA Astrophysics Data System (ADS)

Ambrogio, Giuseppina; Gagliardi, Francesco; Filice, Luigino; Romero, Natalia

2016-10-01

Incremental sheet forming (ISF) consists in deforming only a small region of the workspace through a punch driven by a NC machine. The drawback of this process is its slowness. In this study, a high speed variant has been investigated from both numerical and experimental points of view. The aim has been the design of a FEM model able to perform the material behavior during the high speed process by defining a thermomechanical model. An experimental campaign has been performed by a CNC lathe with high speed to test process feasibility. The first results have shown how the material presents the same performance than in conventional speed ISF and, in some cases, better material behavior due to the temperature increment. An accurate numerical simulation has been performed to investigate the material behavior during the high speed process confirming substantially experimental evidence.

Neural correlates of the difference between working memory speed and simple sensorimotor speed: an fMRI study.

PubMed

Takeuchi, Hikaru; Sugiura, Motoaki; Sassa, Yuko; Sekiguchi, Atsushi; Yomogida, Yukihito; Taki, Yasuyuki; Kawashima, Ryuta

2012-01-01

The difference between the speed of simple cognitive processes and the speed of complex cognitive processes has various psychological correlates. However, the neural correlates of this difference have not yet been investigated. In this study, we focused on working memory (WM) for typical complex cognitive processes. Functional magnetic resonance imaging data were acquired during the performance of an N-back task, which is a measure of WM for typical complex cognitive processes. In our N-back task, task speed and memory load were varied to identify the neural correlates responsible for the difference between the speed of simple cognitive processes (estimated from the 0-back task) and the speed of WM. Our findings showed that this difference was characterized by the increased activation in the right dorsolateral prefrontal cortex (DLPFC) and the increased functional interaction between the right DLPFC and right superior parietal lobe. Furthermore, the local gray matter volume of the right DLPFC was correlated with participants' accuracy during fast WM tasks, which in turn correlated with a psychometric measure of participants' intelligence. Our findings indicate that the right DLPFC and its related network are responsible for the execution of the fast cognitive processes involved in WM. Identified neural bases may underlie the psychometric differences between the speed with which subjects perform simple cognitive tasks and the speed with which subjects perform more complex cognitive tasks, and explain the previous traditional psychological findings.

The physics behind the fizz in champagne and sparkling wines

NASA Astrophysics Data System (ADS)

Liger-Belair, G.

2012-02-01

Bubbles in a glass of champagne may seem like the acme of frivolity to most of people, but in fact they may rather be considered as a fantastic playground for any physicist. Actually, the so-called effervescence process, which enlivens champagne and sparkling wines tasting, is the result of the fine interplay between CO2 dissolved gas molecules, tiny air pockets trapped within microscopic particles during the pouring process, and some both glass and liquid properties. Results obtained concerning the various steps where the CO2 molecule plays a role (from its ingestion in the liquid phase during the fermentation process to its progressive release in the headspace above the tasting glass as bubbles collapse) are gathered and synthesized to propose a self-consistent and global overview of how gaseous and dissolved CO2 impact champagne and sparkling wine science. Physicochemical processes behind the nucleation, rise, and burst of gaseous CO2 bubbles found in glasses poured with champagne and sparkling wines are depicted. Those phenomena observed in close-up through high-speed photography are often visually appealing. I hope that your enjoyment of champagne will be enhanced after reading this fully illustrated review dedicated to the science hidden right under your nose each time you enjoy a glass of champagne.

Verbal Processing Speed and Executive Functioning in Long-Term Cochlear Implant Users

PubMed Central

Pisoni, David B.; Kronenberger, William G.

2015-01-01

Purpose The purpose of this study was to report how verbal rehearsal speed (VRS), a form of covert speech used to maintain verbal information in working memory, and another verbal processing speed measure, perceptual encoding speed, are related to 3 domains of executive function (EF) at risk in cochlear implant (CI) users: verbal working memory, fluency-speed, and inhibition-concentration. Method EF, speech perception, and language outcome measures were obtained from 55 prelingually deaf, long-term CI users and matched controls with normal hearing (NH controls). Correlational analyses were used to assess relations between VRS (articulation rate), perceptual encoding speed (digit and color naming), and the outcomes in each sample. Results CI users displayed slower verbal processing speeds than NH controls. Verbal rehearsal speed was related to 2 EF domains in the NH sample but was unrelated to EF outcomes in CI users. Perceptual encoding speed was related to all EF domains in both groups. Conclusions Verbal rehearsal speed may be less influential for EF quality in CI users than for NH controls, whereas rapid automatized labeling skills and EF are closely related in both groups. CI users may develop processing strategies in EF tasks that differ from the covert speech strategies routinely employed by NH individuals. PMID:25320961

Two speed factors of visual recognition independently correlated with fluid intelligence.

PubMed

Tachibana, Ryosuke; Namba, Yuri; Noguchi, Yasuki

2014-01-01

Growing evidence indicates a moderate but significant relationship between processing speed in visuo-cognitive tasks and general intelligence. On the other hand, findings from neuroscience proposed that the primate visual system consists of two major pathways, the ventral pathway for objects recognition and the dorsal pathway for spatial processing and attentive analysis. Previous studies seeking for visuo-cognitive factors of human intelligence indicated a significant correlation between fluid intelligence and the inspection time (IT), an index for a speed of object recognition performed in the ventral pathway. We thus presently examined a possibility that neural processing speed in the dorsal pathway also represented a factor of intelligence. Specifically, we used the mental rotation (MR) task, a popular psychometric measure for mental speed of spatial processing in the dorsal pathway. We found that the speed of MR was significantly correlated with intelligence scores, while it had no correlation with one's IT (recognition speed of visual objects). Our results support the new possibility that intelligence could be explained by two types of mental speed, one related to object recognition (IT) and another for manipulation of mental images (MR).

Cross-validation of oxygen uptake prediction during walking in ambulatory persons with multiple sclerosis.

PubMed

Agiovlasitis, Stamatis; Motl, Robert W

2016-01-01

An equation for predicting the gross oxygen uptake (gross-VO2) during walking for persons with multiple sclerosis (MS) has been developed. Predictors included walking speed and total score from the 12-Item Multiple Sclerosis Walking Scale (MSWS-12). This study examined the validity of this prediction equation in another sample of persons with MS. Participants were 18 persons with MS with limited mobility problems (42 ± 13 years; 14 women). Participants completed the MSWS-12. Gross-VO2 was measured with open-circuit spirometry during treadmill walking at 2.0, 3.0, and 4.0 mph (0.89, 1.34, and 1.79 m·s(-1)). Absolute percent error was small: 8.3 ± 6.1% , 8.0 ± 5.6% , and 12.2 ± 9.0% at 2.0, 3.0, and 4.0 mph, respectively. Actual gross-VO2 did not differ significantly from predicted gross-VO2 at 2.0 and 3.0 mph, but was significantly higher than predicted gross-VO2 at 4.0 mph (p <  0.001). Bland-Altman plots indicated nearly zero mean difference between actual and predicted gross-VO2 with modest 95% confidence intervals at 2.0 and 3.0 mph, but there was some underestimation at 4.0 mph. Speed and MSWS-12 score provide valid prediction of gross-VO2 during treadmill walking at slow and moderate speeds in ambulatory persons with MS. However, there is a possibility of small underestimation for walking at 4.0 mph.

Large-scale neural circuit mapping data analysis accelerated with the graphical processing unit (GPU).

PubMed

Shi, Yulin; Veidenbaum, Alexander V; Nicolau, Alex; Xu, Xiangmin

2015-01-15

Modern neuroscience research demands computing power. Neural circuit mapping studies such as those using laser scanning photostimulation (LSPS) produce large amounts of data and require intensive computation for post hoc processing and analysis. Here we report on the design and implementation of a cost-effective desktop computer system for accelerated experimental data processing with recent GPU computing technology. A new version of Matlab software with GPU enabled functions is used to develop programs that run on Nvidia GPUs to harness their parallel computing power. We evaluated both the central processing unit (CPU) and GPU-enabled computational performance of our system in benchmark testing and practical applications. The experimental results show that the GPU-CPU co-processing of simulated data and actual LSPS experimental data clearly outperformed the multi-core CPU with up to a 22× speedup, depending on computational tasks. Further, we present a comparison of numerical accuracy between GPU and CPU computation to verify the precision of GPU computation. In addition, we show how GPUs can be effectively adapted to improve the performance of commercial image processing software such as Adobe Photoshop. To our best knowledge, this is the first demonstration of GPU application in neural circuit mapping and electrophysiology-based data processing. Together, GPU enabled computation enhances our ability to process large-scale data sets derived from neural circuit mapping studies, allowing for increased processing speeds while retaining data precision. Copyright © 2014 Elsevier B.V. All rights reserved.

Large scale neural circuit mapping data analysis accelerated with the graphical processing unit (GPU)

PubMed Central

Shi, Yulin; Veidenbaum, Alexander V.; Nicolau, Alex; Xu, Xiangmin

2014-01-01

Background Modern neuroscience research demands computing power. Neural circuit mapping studies such as those using laser scanning photostimulation (LSPS) produce large amounts of data and require intensive computation for post-hoc processing and analysis. New Method Here we report on the design and implementation of a cost-effective desktop computer system for accelerated experimental data processing with recent GPU computing technology. A new version of Matlab software with GPU enabled functions is used to develop programs that run on Nvidia GPUs to harness their parallel computing power. Results We evaluated both the central processing unit (CPU) and GPU-enabled computational performance of our system in benchmark testing and practical applications. The experimental results show that the GPU-CPU co-processing of simulated data and actual LSPS experimental data clearly outperformed the multi-core CPU with up to a 22x speedup, depending on computational tasks. Further, we present a comparison of numerical accuracy between GPU and CPU computation to verify the precision of GPU computation. In addition, we show how GPUs can be effectively adapted to improve the performance of commercial image processing software such as Adobe Photoshop. Comparison with Existing Method(s) To our best knowledge, this is the first demonstration of GPU application in neural circuit mapping and electrophysiology-based data processing. Conclusions Together, GPU enabled computation enhances our ability to process large-scale data sets derived from neural circuit mapping studies, allowing for increased processing speeds while retaining data precision. PMID:25277633

Using GPS-derived speed patterns for recognition of transport modes in adults.

PubMed

Huss, Anke; Beekhuizen, Johan; Kromhout, Hans; Vermeulen, Roel

2014-10-11

Identification of active or sedentary modes of transport is of relevance for studies assessing physical activity or addressing exposure assessment. We assessed in a proof-of-principle study if speed as logged by GPSs could be used to identify modes of transport (walking, bicycling, and motorized transport: car, bus or train). 12 persons commuting to work walking, bicycling or with motorized transport carried GPSs for two commutes and recorded their mode of transport. We evaluated seven speed metrics: mean, 95th percentile of speed, standard deviation of the mean, rate-of-change, standardized-rate-of-change, acceleration and deceleration. We assessed which speed metric would best identify the transport mode using discriminant analyses. We applied cross validation and calculated agreement (Cohen's Kappa) between actual and derived modes of transport. Mode of transport was reliably classified whenever a person used a mode of transport for longer than one minute. Best results were observed when using the 95th percentile of speed, acceleration and deceleration (kappa 0.73). When we combined all motorized traffic into one category, kappa increased to 0.95. GPS-measured speed enable the identification of modes of transport. Given the current low costs of GPS devices and the built-in capacity of GPS tracking in most smartphones, the use of such devices in large epidemiological studies may facilitate the assessment of physical activity related to transport modes, or improve exposure assessment using automated travel mode detection.

Flow speed of the ablation vapors generated during laser drilling of CFRP with a continuous-wave laser beam

NASA Astrophysics Data System (ADS)

Faas, S.; Freitag, C.; Boley, S.; Berger, P.; Weber, R.; Graf, T.

2017-03-01

The hot plume of ablation products generated during the laser drilling process of carbon fiber reinforced plastics (CFRP) with a continuous-wave laser beam was analyzed by means of high-speed imaging. The formation of compression shocks was observed within the flow of the evaporated material, which is an indication of flow speeds well above the local speed of sound. The flow speed of the hot ablation products can be estimated by analyzing the position of these compression shocks. We investigated the temporal evolution of the flow speed during the drilling process and the influence of the average laser power on the flow speed. The flow speed increases with increasing average laser powers. The moment of drilling through the material changes the conditions for the drilling process and was confirmed to influence the flow speed of the ablated material. Compression shocks can also be observed during laser cutting of CFRP with a moving laser beam.

Locomotor Recovery in Spinal Cord Injury: Insights Beyond Walking Speed and Distance.

PubMed

Awai, Lea; Curt, Armin

2016-08-01

Recovery of locomotor function after incomplete spinal cord injury (iSCI) is clinically assessed through walking speed and distance, while improvements in these measures might not be in line with a normalization of gait quality and are, on their own, insensitive at revealing potential mechanisms underlying recovery. The objective of this study was to relate changes of gait parameters to the recovery of walking speed while distinguishing between parameters that rather reflect speed improvements from factors contributing to overall recovery. Kinematic data of 16 iSCI subjects were repeatedly recorded during in-patient rehabilitation. The responsiveness of gait parameters to walking speed was assessed by linear regression. Principal component analysis (PCA) was applied on the multivariate data across time to identify factors that contribute to recovery after iSCI. Parameters of gait cycle and movement dynamics were both responsive and closely related to the recovery of walking speed, which increased by 96%. Multivariate analysis revealed specific gait parameters (intralimb shape normality and consistency) that, although less related to speed increments, loaded highly on principal component one (PC1) (58.6%) explaining the highest proportion of variance (i.e., recovery of outcome over time). Interestingly, measures of hip, knee, and ankle range of motion showed varying degrees of responsiveness (from very high to very low) while not contributing to gait recovery as revealed by PCA. The conjunct application of two analysis methods distinguishes gait parameters that simply reflect increased walking speed from parameters that actually contribute to gait recovery in iSCI. This distinction may be of value for the evaluation of interventions for locomotor recovery.

Passive air sampling using semipermeable membrane devices at different wind-speeds in situ calibrated by performance reference compounds.

PubMed

Söderström, Hanna S; Bergqvist, Per-Anders

2004-09-15

Semipermeable membrane devices (SPMDs) are passive samplers used to measure the vapor phase of organic pollutants in air. This study tested whether extremely high wind-speeds during a 21-day sampling increased the sampling rates of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs), and whether the release of performance reference compounds (PRCs) was related to the uptakes at different wind-speeds. Five samplers were deployed in an indoor, unheated, and dark wind tunnel with different wind-speeds at each site (6-50 m s(-1)). In addition, one sampler was deployed outside the wind tunnel and one outside the building. To test whether a sampler, designed to reduce the wind-speeds, decreased the uptake and release rates, each sampler in the wind tunnel included two SPMDs positioned inside a protective device and one unprotected SPMD outside the device. The highest amounts of PAHs and PCBs were found in the SPMDs exposed to the assumed highest wind-speeds. Thus, the SPMD sampling rates increased with increasing wind-speeds, indicating that the uptake was largely controlled by the boundary layer at the membrane-air interface. The coefficient of variance (introduced by the 21-day sampling and the chemical analysis) for the air concentrations of three PAHs and three PCBs, calculated using the PRC data, was 28-46%. Thus, the PRCs had a high ability to predict site effects of wind and assess the actual sampling situation. Comparison between protected and unprotected SPMDs showed that the sampler design reduced the wind-speed inside the devices and thereby the uptake and release rates.

Groundspeed filtering for CTAS

NASA Technical Reports Server (NTRS)

Slater, Gary L.

1994-01-01

Ground speed is one of the radar observables which is obtained along with position and heading from NASA Ames Center radar. Within the Center TRACON Automation System (CTAS), groundspeed is converted into airspeed using the wind speeds which CTAS obtains from the NOAA weather grid. This airspeed is then used in the trajectory synthesis logic which computes the trajectory for each individual aircraft. The time history of the typical radar groundspeed data is generally quite noisy, with high frequency variations on the order of five knots, and occasional 'outliers' which can be significantly different from the probable true speed. To try to smooth out these speeds and make the ETA estimate less erratic, filtering of the ground speed is done within CTAS. In its base form, the CTAS filter is a 'moving average' filter which averages the last ten radar values. In addition, there is separate logic to detect and correct for 'outliers', and acceleration logic which limits the groundspeed change in adjacent time samples. As will be shown, these additional modifications do cause significant changes in the actual groundspeed filter output. The conclusion is that the current ground speed filter logic is unable to track accurately the speed variations observed on many aircraft. The Kalman filter logic however, appears to be an improvement to the current algorithm used to smooth ground speed variations, while being simpler and more efficient to implement. Additional logic which can test for true 'outliers' can easily be added by looking at the difference in the a priori and post priori Kalman estimates, and not updating if the difference in these quantities is too large.

Evaluation of Ohio work zone speed zones process.

DOT National Transportation Integrated Search

2014-06-01

This report describes the methodology and results of analyses performed to determine the effectiveness of Ohio Department of Transportation processes for establishing work zone speed zones. Researchers observed motorists speed choice upstream of a...

Local Structure Analysis and Interface Layer Effect of Phase-Change Recording Material Using Actual Media

NASA Astrophysics Data System (ADS)

Nakai, Tsukasa; Yoshiki, Masahiko; Satoh, Yasuhiro; Ashida, Sumio

2008-07-01

The influences of the interface layer on crystal structure, the local atomic arrangement, and the electronic and chemical structure of a GeBiTe (GBT) phase-change recording material have been investigated using X-ray diffraction (XRD), X-ray absorption fine structure (XAFS), and hard X-ray photoelectron spectroscopy (HX-PES) methods using actual rewritable high-speed HD DVD media without special sample processing. XRD results showed that the crystal structure of laser-crystallized GBT alloy in the actual HD DVD media is the same as that of GeSbTe (GST) alloy, which has a NaCl-type structure. No differences between samples with and without interface layers were found. The lattice constant of GBT is larger than that of GST. Bi increases the lattice constant of GST with respect to the Bi substitution ratio of Sb. According to HX-PES, the DOS of in the recording film amorphous state with an interface layer is closer to that of the crystalline state than the recording film without an interface layer. From XAFS results, clear differences between amorphous (Amo.) and crystalline states (Cry.) were observed. The interatomic distance of amorphous recording material is independent of the existence of an interface layer. On the other hand, the coordination number varied slightly due to the presence of the interface layer. Therefore, the electronic state of the recording layer changes because of the interface layer, although the local structure changes only slightly except for the coordination number. Combining these results, we conclude that the interface layer changes the electronic state of the recording layer and promotes crystallization, but only affects the local structure of the atomic arrangement slightly.

Kinematic properties of solar coronal mass ejections: Correction for projection effects in spacecraft coronagraph measurements

NASA Astrophysics Data System (ADS)

Howard, T. A.; Nandy, D.; Koepke, A. C.

2008-01-01

One of the main sources of uncertainty in quantifying the kinematic properties of coronal mass ejections (CMEs) using coronagraphs is the fact that coronagraph images are projected into the sky plane, resulting in measurements which can differ significantly from their actual values. By identifying solar surface source regions of CMEs using X-ray and Hα flare and disappearing filament data, and through considerations of CME trajectories in three-dimensional (3-D) geometry, we have devised a methodology to correct for the projection effect. We outline this method here. The methodology was automated and applied to over 10,000 CMEs in the Coordinated Data Analysis Workshop (CDAW) (SOHO Large Angle Spectroscopic Coronagraph) catalog spanning 1996-2005, in which we could associate 1961 CMEs with an appropriate surface event. In the latter subset, deprojected speeds, accelerations, and launch angles were determined to study CME kinematics. Our analysis of this subset of events reconfirms some important trends, notably that previously uncovered solar cycle variation of CME properties are preserved, CMEs with greater width have higher speeds, and slower CMEs tend to accelerate while faster CMEs tend to decelerate. This points out that statistical trends in CME properties, recovered from plane-of-sky measurements, may be preserved even in the face of more sophisticated 3-D measurements from spacecrafts such as STEREO, if CME trajectories are predominantly radial. However, our results also show that the magnitude of corrected measurements can differ significantly from the projected plane-of-sky measurements on a case-by-case basis and that acceleration is more sensitive to the deprojection process than speed. Average corrected speed and acceleration tend to be a factor of 1.7 and 4.4 higher than their projected values, with mean corrected speed and acceleration magnitudes being on the order of 1000 km/s and 50 m/s2, respectively. We conclude that while using the plane-of-sky measurements may be suitable for studies of general trends in a large sample of events, correcting for projection effects is mandatory for those investigations which rely on a numerically precise determination of the properties of individual CMEs.

Information processing speed as a predictor of IQ in children with and without specific language impairment in grades 3 and 8.

PubMed

Park, Jisook; Mainela-Arnold, Elina; Miller, Carol A

2015-01-01

This study investigated (1) whether nonlinguistic processing speed predicts nonverbal IQ in TD children and children with SLI and (2) if the proposed relationship is different at two time points. The participants consisted of a subset of a longitudinal dataset, 55 typically developing children and 55 children with SLI. Children completed four nonverbal speed tasks and four subtests of the WISC-III. The WISC-III subtests requiring timed and untimed responses were examined separately. Linear mixed model analyses indicated that in both groups, processing speed predicted nonverbal IQ subtests that reward speedy responses, but not IQ subtests that do not. The relationships between processing speed and IQ with speed bonuses did not differ at grades 3 and 8, and these relationships also were not significantly different in children with SLI and their TD peers. The results suggest that the presence of processing speed limitations in many children with SLI raises questions about the utility of timed nonverbal IQ measures as tools for diagnosis of SLI. Future studies should investigate other cognitive assessments that could be used as inclusionary criteria for SLI. The reader will be able to (1) describe the relationship between processing speed and nonverbal IQ in children with TD and SLI and (2) discuss problems using an IQ criterion to diagnose children as having SLI. Copyright © 2014 Elsevier Inc. All rights reserved.

Functional MRI evidence for the decline of word retrieval and generation during normal aging.

PubMed

Baciu, M; Boudiaf, N; Cousin, E; Perrone-Bertolotti, M; Pichat, C; Fournet, N; Chainay, H; Lamalle, L; Krainik, A

2016-02-01

This fMRI study aimed to explore the effect of normal aging on word retrieval and generation. The question addressed is whether lexical production decline is determined by a direct mechanism, which concerns the language operations or is rather indirectly induced by a decline of executive functions. Indeed, the main hypothesis was that normal aging does not induce loss of lexical knowledge, but there is only a general slowdown in retrieval mechanisms involved in lexical processing, due to possible decline of the executive functions. We used three tasks (verbal fluency, object naming, and semantic categorization). Two groups of participants were tested (Young, Y and Aged, A), without cognitive and psychiatric impairment and showing similar levels of vocabulary. Neuropsychological testing revealed that older participants had lower executive function scores, longer processing speeds, and tended to have lower verbal fluency scores. Additionally, older participants showed higher scores for verbal automatisms and overlearned information. In terms of behavioral data, older participants performed as accurate as younger adults, but they were significantly slower for the semantic categorization and were less fluent for verbal fluency task. Functional MRI analyses suggested that older adults did not simply activate fewer brain regions involved in word production, but they actually showed an atypical pattern of activation. Significant correlations between the BOLD (Blood Oxygen Level Dependent) signal of aging-related (A > Y) regions and cognitive scores suggested that this atypical pattern of the activation may reveal several compensatory mechanisms (a) to overcome the slowdown in retrieval, due to the decline of executive functions and processing speed and (b) to inhibit verbal automatic processes. The BOLD signal measured in some other aging-dependent regions did not correlate with the behavioral and neuropsychological scores, and the overactivation of these uncorrelated regions would simply reveal dedifferentiation that occurs with aging. Altogether, our results suggest that normal aging is associated with a more difficult access to lexico-semantic operations and representations by a slowdown in executive functions, without any conceptual loss.

Modeling of Dendritic Evolution of Continuously Cast Steel Billet with Cellular Automaton

NASA Astrophysics Data System (ADS)

Wang, Weiling; Ji, Cheng; Luo, Sen; Zhu, Miaoyong

2018-02-01

In order to predict the dendritic evolution during the continuous steel casting process, a simple mechanism to connect the heat transfer at the macroscopic scale and the dendritic growth at the microscopic scale was proposed in the present work. As the core of the across-scale simulation, a two-dimensional cell automaton (CA) model with a decentered square algorithm was developed and parallelized. Apart from nucleation undercooling and probability, a temperature gradient was introduced to deal with the columnar-to-equiaxed transition (CET) by considering its variation during continuous casting. Based on the thermal history, the dendritic evolution in a 4 mm × 40 mm region near the centerline of a SWRH82B steel billet was predicted. The influences of the secondary cooling intensity, superheat, and casting speed on the dendritic structure of the billet were investigated in detail. The results show that the predicted equiaxed dendritic solidification of Fe-5.3Si alloy and columnar dendritic solidification of Fe-0.45C alloy are consistent with in situ experimental results [Yasuda et al. Int J Cast Metals Res 22:15-21 (2009); Yasuda et al. ISIJ Int 51:402-408 (2011)]. Moreover, the predicted dendritic arm spacing and CET location agree well with the actual results in the billet. The primary dendrite arm spacing of columnar dendrites decreases with increasing secondary cooling intensity, or decreasing superheat and casting speed. Meanwhile, the CET is promoted as the secondary cooling intensity and superheat decrease. However, the CET is not influenced by the casting speed, owing to the adjusting of the flow rate of secondary spray water. Compared with the superheat and casting speed, the secondary cooling intensity can influence the cooling rate and temperature gradient in deeper locations, and accordingly exerts a more significant influence on the equiaxed dendritic structure.

Future applications of associative processor systems to operational KSC systems for optimizing cost and enhancing performance characteristics

NASA Technical Reports Server (NTRS)

Perkinson, J. A.

1974-01-01

The application of associative memory processor equipment to conventional host processors type systems is discussed. Efforts were made to demonstrate how such application relieves the task burden of conventional systems, and enhance system speed and efficiency. Data cover comparative theoretical performance analysis, demonstration of expanded growth capabilities, and demonstrations of actual hardware in simulated environment.

Accurate calculation of multispar cantilever and semicantilever wings with parallel webs under direct and indirect loading

NASA Technical Reports Server (NTRS)

Sanger, Eugen

1932-01-01

In the present report the computation is actually carried through for the case of parallel spars of equal resistance in bending without direct loading, including plotting of the influence lines; for other cases the method of calculation is explained. The development of large size airplanes can be speeded up by accurate methods of calculation such as this.

The application of measurement techniques to track flutter testing

NASA Technical Reports Server (NTRS)

Roglin, H. R.

1975-01-01

The application is discussed of measurement techniques to captive flight flutter tests at the Supersonic Naval Ordnance Research Track (SNORT), U. S. Naval Ordnance Test Station, China Lake, California. The high-speed track, by its ability to prove the validity of design and to accurately determine the actual margin of safety, offers a unique method of flutter testing for the aircraft design engineer.

Normative Topographic ERP Analyses of Speed of Speech Processing and Grammar Before and After Grammatical Treatment

PubMed Central

Yoder, Paul J.; Molfese, Dennis; Murray, Micah M.; Key, Alexandra P. F.

2013-01-01

Typically developing (TD) preschoolers and age-matched preschoolers with specific language impairment (SLI) received event-related potentials (ERPs) to four monosyllabic speech sounds prior to treatment and, in the SLI group, after 6 months of grammatical treatment. Before treatment, the TD group processed speech sounds faster than the SLI group. The SLI group increased the speed of their speech processing after treatment. Post-treatment speed of speech processing predicted later impairment in comprehending phrase elaboration in the SLI group. During the treatment phase, change in speed of speech processing predicted growth rate of grammar in the SLI group. PMID:24219693

An Analysis of the Actual Processes of Physicists' Research and the Implications for Teaching Scientific Inquiry in School

ERIC Educational Resources Information Center

Park, Jongwon; Jang, Kyoung-Ae; Kim, Ikgyun

2009-01-01

Investigation of scientists' actual processes of conducting research can provide us with more realistic aspects of scientific inquiry. This study was performed to identify three aspects of scientists' actual research: their motivations for scientific inquiry, the scientific inquiry skills they used, and the main types of results obtained from…

Executive functioning and processing speed in age-related differences in memory: contribution of a coding task.

PubMed

Baudouin, Alexia; Clarys, David; Vanneste, Sandrine; Isingrini, Michel

2009-12-01

The aim of the present study was to examine executive dysfunctioning and decreased processing speed as potential mediators of age-related differences in episodic memory. We compared the performances of young and elderly adults in a free-recall task. Participants were also given tests to measure executive functions and perceptual processing speed and a coding task (the Digit Symbol Substitution Test, DSST). More precisely, we tested the hypothesis that executive functions would mediate the age-related differences observed in the free-recall task better than perceptual speed. We also tested the assumption that a coding task, assumed to involve both executive processes and perceptual speed, would be the best mediator of age-related differences in memory. Findings first confirmed that the DSST combines executive processes and perceptual speed. Secondly, they showed that executive functions are a significant mediator of age-related differences in memory, and that DSST performance is the best predictor.

Two Independent Contributions to Step Variability during Over-Ground Human Walking

PubMed Central

Collins, Steven H.; Kuo, Arthur D.

2013-01-01

Human walking exhibits small variations in both step length and step width, some of which may be related to active balance control. Lateral balance is thought to require integrative sensorimotor control through adjustment of step width rather than length, contributing to greater variability in step width. Here we propose that step length variations are largely explained by the typical human preference for step length to increase with walking speed, which itself normally exhibits some slow and spontaneous fluctuation. In contrast, step width variations should have little relation to speed if they are produced more for lateral balance. As a test, we examined hundreds of overground walking steps by healthy young adults (N = 14, age < 40 yrs.). We found that slow fluctuations in self-selected walking speed (2.3% coefficient of variation) could explain most of the variance in step length (59%, P < 0.01). The residual variability not explained by speed was small (1.5% coefficient of variation), suggesting that step length is actually quite precise if not for the slow speed fluctuations. Step width varied over faster time scales and was independent of speed fluctuations, with variance 4.3 times greater than that for step length (P < 0.01) after accounting for the speed effect. That difference was further magnified by walking with eyes closed, which appears detrimental to control of lateral balance. Humans appear to modulate fore-aft foot placement in precise accordance with slow fluctuations in walking speed, whereas the variability of lateral foot placement appears more closely related to balance. Step variability is separable in both direction and time scale into balance- and speed-related components. The separation of factors not related to balance may reveal which aspects of walking are most critical for the nervous system to control. PMID:24015308

Infant Visual Recognition Memory: Independent Contributions of Speed and Attention.

ERIC Educational Resources Information Center

Rose, Susan A.; Feldman, Judith F.; Jankowski, Jeffery J.

2003-01-01

Examined contributions of cognitive processing speed, short-term memory capacity, and attention to infant visual recognition memory. Found that infants who showed better attention and faster processing had better recognition memory. Contributions of attention and processing speed were independent of one another and similar at all ages studied--5,…

Cultural Differences in the Development of Processing Speed

ERIC Educational Resources Information Center

Kail, Robert V.; McBride-Chang, Catherine; Ferrer, Emilio; Cho, Jeung-Ryeul; Shu, Hua

2013-01-01

The aim of the present work was to examine cultural differences in the development of speed of information processing. Four samples of US children ("N" = 509) and four samples of East Asian children ("N" = 661) completed psychometric measures of processing speed on two occasions. Analyses of the longitudinal data indicated…

General airplane performance

NASA Technical Reports Server (NTRS)

Rockfeller, W C

1939-01-01

Equations have been developed for the analysis of the performance of the ideal airplane, leading to an approximate physical interpretation of the performance problem. The basic sea-level airplane parameters have been generalized to altitude parameters and a new parameter has been introduced and physically interpreted. The performance analysis for actual airplanes has been obtained in terms of the equivalent ideal airplane in order that the charts developed for use in practical calculations will for the most part apply to any type of engine-propeller combination and system of control, the only additional material required consisting of the actual engine and propeller curves for propulsion unit. Finally, a more exact method for the calculation of the climb characteristics for the constant-speed controllable propeller is presented in the appendix.

Perceived visual speed constrained by image segmentation

NASA Technical Reports Server (NTRS)

Verghese, P.; Stone, L. S.

1996-01-01

Little is known about how or where the visual system parses the visual scene into objects or surfaces. However, it is generally assumed that the segmentation and grouping of pieces of the image into discrete entities is due to 'later' processing stages, after the 'early' processing of the visual image by local mechanisms selective for attributes such as colour, orientation, depth, and motion. Speed perception is also thought to be mediated by early mechanisms tuned for speed. Here we show that manipulating the way in which an image is parsed changes the way in which local speed information is processed. Manipulations that cause multiple stimuli to appear as parts of a single patch degrade speed discrimination, whereas manipulations that perceptually divide a single large stimulus into parts improve discrimination. These results indicate that processes as early as speed perception may be constrained by the parsing of the visual image into discrete entities.

Verbal Processing Speed and Executive Functioning in Long-Term Cochlear Implant Users

ERIC Educational Resources Information Center

AuBuchon, Angela M.; Pisoni, David B.; Kronenberger, William G.

2015-01-01

Purpose: The purpose of this study was to report how "verbal rehearsal speed" (VRS), a form of covert speech used to maintain verbal information in working memory, and another verbal processing speed measure, perceptual encoding speed, are related to 3 domains of executive function (EF) at risk in cochlear implant (CI) users: verbal…

Relative association of processing speed, short-term memory and sustained attention with task on gait speed: a study of community-dwelling people 50 years and older.

PubMed

Killane, Isabelle; Donoghue, Orna A; Savva, George M; Cronin, Hilary; Kenny, Rose Anne; Reilly, Richard B

2014-11-01

For single gait tasks, associations have been reported between gait speed and cognitive domains. However, few studies have evaluated if this association is altered in dual gait tasks given gait speed changes with complexity and nature of task. We evaluated relative contributions of specific elements of cognitive function (including sustained attention and processing speed) to dual task gait speed in a nationally representative population of community-dwelling adults over 50 years. Gait speed was obtained using the GaitRite walkway during three gait tasks: single, cognitive (alternate letters), and motor (carrying a filled glass). Linear regression models, adjusted for covariates, were constructed to predict the relative contributions of seven neuropsychological tests to gait speed differences and to investigate gait task effects. The mean age and gait speed of the population (n = 4,431, 55% women) was 62.4 years (SD = 8.2) and 135.85 cm/s (SD = 20.20, single task), respectively. Poorer processing speed, short-term memory, and sustained attention were major cognitive contributors to slower gait speed for all gait tasks. Both dual gait tasks were robust to covariate adjustment and had a significant additional executive function element not found for the single gait task. For community-dwelling older adults processing speed, short-term memory and sustained attention were independently associated with gait speed for all gait tasks. Dual gait tasks were found to highlight specific executive function elements. This result forms a baseline value for dual task gait speed. © The Author 2014. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Processing speed and working memory span: their differential role in superficial and deep memory processes in schizophrenia.

PubMed

Brébion, Gildas; Bressan, Rodrigo A; Pilowsky, Lyn S; David, Anthony S

2011-05-01

Previous work has suggested that decrement in both processing speed and working memory span plays a role in the memory impairment observed in patients with schizophrenia. We undertook a study to examine simultaneously the effect of these two factors. A sample of 49 patients with schizophrenia and 43 healthy controls underwent a battery of verbal and visual memory tasks. Superficial and deep encoding memory measures were tallied. We conducted regression analyses on the various memory measures, using processing speed and working memory span as independent variables. In the patient group, processing speed was a significant predictor of superficial and deep memory measures in verbal and visual memory. Working memory span was an additional significant predictor of the deep memory measures only. Regression analyses involving all participants revealed that the effect of diagnosis on all the deep encoding memory measures was reduced to non-significance when processing speed was entered in the regression. Decreased processing speed is involved in verbal and visual memory deficit in patients, whether the task require superficial or deep encoding. Working memory is involved only insofar as the task requires a certain amount of effort.

Shadow: Running Tor in a Box for Accurate and Efficient Experimentation

DTIC Science & Technology

2011-09-23

Modeling the speed of a target CPU is done by running an OpenSSL [31] speed test on a real CPU of that type. This provides us with the raw CPU processing...rate, but we are also interested in the processing speed of an application. By running application 5 benchmarks on the same CPU as the OpenSSL speed test...simulation, saving CPU cy- cles on our simulation host machine. Shadow removes cryptographic processing by preloading the main OpenSSL [31] functions used

Is there really an eccentric action of the hamstrings during the swing phase of high-speed running? part I: A critical review of the literature.

PubMed

Van Hooren, Bas; Bosch, Frans

2017-12-01

It is widely assumed that there is an eccentric hamstring muscle fibre action during the swing phase of high-speed running. However, animal and modelling studies in humans show that the increasing distance between musculotendinous attachment points during forward swing is primarily due to passive lengthening associated with the take-up of muscle slack. Later in the swing phase, the contractile element (CE) maintains a near isometric action while the series elastic (tendinous) element first stretches as the knee extends, and then recoils causing the swing leg to forcefully retract prior to ground contact. Although modelling studies showed some active lengthening of the contractile (muscular) element during the mid-swing phase of high-speed running, we argue that the increasing distance between the attachment points should not be interpreted as an eccentric action of the CE due to the effects of muscle slack. Therefore, there may actually be no significant eccentric, but rather predominantly an isometric action of the hamstrings CE during the swing phase of high-speed running when the attachment points of the hamstrings are moving apart. Based on this, we propose that isometric rather than eccentric exercises are a more specific way of conditioning the hamstrings for high-speed running.

The response of a high-speed train wheel to a harmonic wheel-rail force

NASA Astrophysics Data System (ADS)

Sheng, Xiaozhen; Liu, Yuxia; Zhou, Xin

2016-09-01

The maximum speed of China's high-speed trains currently is 300km/h and expected to increase to 350-400km/h. As a wheel travels along the rail at such a high speed, it is subject to a force rotating at the same speed along its periphery. This fast moving force contains not only the axle load component, but also many components of high frequencies generated from wheel-rail interactions. Rotation of the wheel also introduces centrifugal and gyroscopic effects. How the wheel responds is fundamental to many issues, including wheel-rail contact, traction, wear and noise. In this paper, by making use of its axial symmetry, a special finite element scheme is developed for responses of a train wheel subject to a vertical and harmonic wheel-rail force. This FE scheme only requires a 2D mesh over a cross-section containing the wheel axis but includes all the effects induced by wheel rotation. Nodal displacements, as a periodic function of the cross-section angle 6, can be decomposed, using Fourier series, into a number of components at different circumferential orders. The derived FE equation is solved for each circumferential order. The sum of responses at all circumferential orders gives the actual response of the wheel.

Laser beam heat method reported

NASA Astrophysics Data System (ADS)

Tsuchiya, Hachiro; Goto, Hidekazu

1988-07-01

An outline of research involving the processing method utilizing laser-induced thermochemistry was presented, with the CO2 laser processing of ceramics in CF4 gas used as a practical processing example. It has become clear that it will be possible to conduct laser proccessing of ceramics with high efficiency and high precision by utilizing the thermochemical processes, but it is not believed that the present method is the best one and it is not clear that it can be applied to commercial processing. It is thought that the processing characteristics of this method will be greatly changed by the combination of the atmospheric gas and the material, and it is important to conduct tests on various combinations. However, it is believed that the improvement and development will become possible by theoretically confirming the basic process of the processing, especially of the the thermochemical process between the solid surface and the atmospheric gas molecule. Actually, it is believed that the thermochemical process on the solid surface is quite complicated. For example, it was confirmed that when thermochemical processing the Si monocrystal in the CF4 gas, the processing speed would change by at least 10 times through changing the gas pressure and the mixing O2 gas density. However, conversely speaking, it is believed that the fact that this method is complicated, with many unexplained points and room for research, conceals the possibility of its being applied to various fields, and also, in this sense, the quantitative confirmation of its basic process in an important problem to be solved in the future.

“The Relationship between Executive Functioning, Processing Speed and White Matter Integrity in Multiple Sclerosis”

PubMed Central

Genova, Helen M.; DeLuca, John; Chiaravalloti, Nancy; Wylie, Glenn

2014-01-01

The primary purpose of the current study was to examine the relationship between performance on executive tasks and white matter integrity, assessed by diffusion tensor imaging (DTI) in Multiple Sclerosis (MS). A second aim was to examine how processing speed affects the relationship between executive functioning and FA. This relationship was examined in two executive tasks that rely heavily on processing speed: the Color-Word Interference Test and Trail-Making Test (Delis-Kaplan Executive Function System). It was hypothesized that reduced fractional anisotropy (FA) is related to poor performance on executive tasks in MS, but that this relationship would be affected by the statistical correction of processing speed from the executive tasks. 15 healthy controls and 25 persons with MS participated. Regression analyses were used to examine the relationship between executive functioning and FA, both before and after processing speed was removed from the executive scores. Before processing speed was removed from the executive scores, reduced FA was associated with poor performance on Color-Word Interference Test and Trail-Making Test in a diffuse network including corpus callosum and superior longitudinal fasciculus. However, once processing speed was removed, the relationship between executive functions and FA was no longer significant on the Trail Making test, and significantly reduced and more localized on the Color-Word Interference Test. PMID:23777468

Decision support for operations and maintenance (DSOM) system

DOEpatents

Jarrell, Donald B [Kennewick, WA; Meador, Richard J [Richland, WA; Sisk, Daniel R [Richland, WA; Hatley, Darrel D [Kennewick, WA; Brown, Daryl R [Richland, WA; Keibel, Gary R [Richland, WA; Gowri, Krishnan [Richland, WA; Reyes-Spindola, Jorge F [Richland, WA; Adams, Kevin J [San Bruno, CA; Yates, Kenneth R [Lake Oswego, OR; Eschbach, Elizabeth J [Fort Collins, CO; Stratton, Rex C [Richland, WA

2006-03-21

A method for minimizing the life cycle cost of processes such as heating a building. The method utilizes sensors to monitor various pieces of equipment used in the process, for example, boilers, turbines, and the like. The method then performs the steps of identifying a set optimal operating conditions for the process, identifying and measuring parameters necessary to characterize the actual operating condition of the process, validating data generated by measuring those parameters, characterizing the actual condition of the process, identifying an optimal condition corresponding to the actual condition, comparing said optimal condition with the actual condition and identifying variances between the two, and drawing from a set of pre-defined algorithms created using best engineering practices, an explanation of at least one likely source and at least one recommended remedial action for selected variances, and providing said explanation as an output to at least one user.

Assessment of processing speed in children with mild TBI: a "first look" at the validity of pediatric ImPACT.

PubMed

Newman, Julie B; Reesman, Jennifer H; Vaughan, Christopher G; Gioia, Gerard A

2013-01-01

Deficit in the speed of cognitive processing is a commonly identified neuropsychological change in children recovering from a mild TBI. However, there are few validated child assessment instruments that allow for serial assessment over the course of recovery in this population. Pediatric ImPACT is a novel measure that purports to assess cognitive speed, learning, and efficiency in this population. The current study sought to validate the use of this new measure by comparing it to traditional paper and pencil measures of processing speed. One hundred and sixty-four children (71% male) age 5-12 with mild TBI evaluated in an outpatient concussion clinic were administered Pediatric ImPACT and other neuropsychological test measures as part of a flexible test battery. Performance on the Response Speed Composite of Pediatric ImPACT was more strongly associated with other measures of cognitive processing speed, than with measures of immediate/working memory and learning/memory in this sample of injured children. There is preliminary support for convergent and discriminant validity of Pediatric ImPACT as a measure for use in post-concussion evaluations of processing speed in children.

Verbal Working Memory in Older Adults: The Roles of Phonological Capacities and Processing Speed

ERIC Educational Resources Information Center

Nittrouer, Susan; Lowenstein, Joanna H.; Wucinich, Taylor; Moberly, Aaron C.

2016-01-01

Purpose: This study examined the potential roles of phonological sensitivity and processing speed in age-related declines of verbal working memory. Method: Twenty younger and 25 older adults with age-normal hearing participated. Two measures of verbal working memory were collected: digit span and serial recall of words. Processing speed was…

We can predict when driving is no longer safe for people who have HD using standard neuropsychological measures.

PubMed

Hennig, Bonnie L; Kaplan, Richard F; Nowicki, Ariel E; Barclay, Jessy E; Gertsberg, Anna G

2014-01-01

Early cognitive dysfunction in Huntington's Disease (HD) is typically of a subcortical frontal executive type, with bradyphrenia, poor spatial and working memory, poor planning and organization, a lack of judgment, and poor mental flexibility. Although there is literature suggesting a correlation between deficits in speed of processing, working memory and executive function on driving competency, there is little direct evidence comparing these declines on tests to actual driving skills. The current study examines the utility of specific neuropsychological measures in predicting actual driving competency in patients with HD. Fifty-two patients at the UConn Health HD Program underwent yearly neuropsychological evaluations and were included in this study. Four scales were chosen a priori to predict driving impairment because of their reported relationship to driving ability. Within each test category, subjects who scored below the threshold suggestive of neurological impairment were found to have results within the impaired range (1.5 standard deviations below corrective normative data). A referral to the Connecticut Department of Motor Vehicles (DMV) for a driving evaluation was subsequently made on patients who were found impaired on any two of these tests. The authors found a strong relationship between scores on a simple battery of four neuropsychological tests and driving competency. This short battery may prove of pragmatic value for clinicians working with people with HD and their families.

Design of permanent magnet synchronous motor speed loop controller based on sliding mode control algorithm

NASA Astrophysics Data System (ADS)

Qiang, Jiang; Meng-wei, Liao; Ming-jie, Luo

2018-03-01

Abstract.The control performance of Permanent Magnet Synchronous Motor will be affected by the fluctuation or changes of mechanical parameters when PMSM is applied as driving motor in actual electric vehicle,and external disturbance would influence control robustness.To improve control dynamic quality and robustness of PMSM speed control system, a new second order integral sliding mode control algorithm is introduced into PMSM vector control.The simulation results show that, compared with the traditional PID control,the modified control scheme optimized has better control precision and dynamic response ability and perform better with a stronger robustness facing external disturbance,it can effectively solve the traditional sliding mode variable structure control chattering problems as well.

Transition fronts of time periodic bistable reaction-diffusion equations in RN

NASA Astrophysics Data System (ADS)

Sheng, Wei-Jie; Guo, Hong-Jun

2018-09-01

This paper is concerned with the existence and qualitative properties of transition fronts for time periodic bistable reaction-diffusion equations in RN. We first show that any almost-planar transition front is actually planar, regardless of the number of transition layers. Then we prove that all transition fronts admit a global mean speed γ and it holds γ = | c |, where c is the speed of the planar traveling front. Finally we establish the existence of a transition front in RN that is not a standard traveling front. Such a front behaves like three moving time periodic planar fronts as time goes to -∞ and like a time periodic V-shaped traveling front as time goes to ∞.

Stalling of Helicopter Blades

NASA Technical Reports Server (NTRS)

Gustafson, F B; Myers, G C , Jr

1946-01-01

Theoretical studies have predicted that operation of helicopter rotor beyond certain combinations of thrust, forward speed, and rotational speed might be prevented by rapidly increasing stalling of the retreating blade. The same studies also indicate that the efficiency of the rotor will increase until these limits are reached or closely approached, so that it is desirable to design helicopter rotors for operation close to the limits imposed by blade stalling. Inasmuch as the theoretical predictions of blade stalling involve numerous approximations and assumptions, an experimental investigation was needed to determine whether, in actual practice, the stall did occur and spread as predicted and to establish the amount of stalling that could be present without severe vibration or control difficulties being introduced. This report presents the results of such an investigation.

Two Speed Factors of Visual Recognition Independently Correlated with Fluid Intelligence

PubMed Central

Tachibana, Ryosuke; Namba, Yuri; Noguchi, Yasuki

2014-01-01

Growing evidence indicates a moderate but significant relationship between processing speed in visuo-cognitive tasks and general intelligence. On the other hand, findings from neuroscience proposed that the primate visual system consists of two major pathways, the ventral pathway for objects recognition and the dorsal pathway for spatial processing and attentive analysis. Previous studies seeking for visuo-cognitive factors of human intelligence indicated a significant correlation between fluid intelligence and the inspection time (IT), an index for a speed of object recognition performed in the ventral pathway. We thus presently examined a possibility that neural processing speed in the dorsal pathway also represented a factor of intelligence. Specifically, we used the mental rotation (MR) task, a popular psychometric measure for mental speed of spatial processing in the dorsal pathway. We found that the speed of MR was significantly correlated with intelligence scores, while it had no correlation with one’s IT (recognition speed of visual objects). Our results support the new possibility that intelligence could be explained by two types of mental speed, one related to object recognition (IT) and another for manipulation of mental images (MR). PMID:24825574

A watershed model of individual differences in fluid intelligence.

PubMed

Kievit, Rogier A; Davis, Simon W; Griffiths, John; Correia, Marta M; Cam-Can; Henson, Richard N

2016-10-01

Fluid intelligence is a crucial cognitive ability that predicts key life outcomes across the lifespan. Strong empirical links exist between fluid intelligence and processing speed on the one hand, and white matter integrity and processing speed on the other. We propose a watershed model that integrates these three explanatory levels in a principled manner in a single statistical model, with processing speed and white matter figuring as intermediate endophenotypes. We fit this model in a large (N=555) adult lifespan cohort from the Cambridge Centre for Ageing and Neuroscience (Cam-CAN) using multiple measures of processing speed, white matter health and fluid intelligence. The model fit the data well, outperforming competing models and providing evidence for a many-to-one mapping between white matter integrity, processing speed and fluid intelligence. The model can be naturally extended to integrate other cognitive domains, endophenotypes and genotypes. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Gliding flight in a jackdaw: a wind tunnel study.

PubMed

Rosén, M; Hedenström, A

2001-03-01

We examined the gliding flight performance of a jackdaw Corvus monedula in a wind tunnel. The jackdaw was able to glide steadily at speeds between 6 and 11 m s(-1). The bird changed its wingspan and wing area over this speed range, and we measured the so-called glide super-polar, which is the envelope of fixed-wing glide polars over a range of forward speeds and sinking speeds. The glide super-polar was an inverted U-shape with a minimum sinking speed (V(ms)) at 7.4 m s(-1) and a speed for best glide (V(bg)) at 8.3 m s(-)). At the minimum sinking speed, the associated vertical sinking speed was 0.62 m s(-1). The relationship between the ratio of lift to drag (L:D) and airspeed showed an inverted U-shape with a maximum of 12.6 at 8.5 m s(-1). Wingspan decreased linearly with speed over the whole speed range investigated. The tail was spread extensively at low and moderate speeds; at speeds between 6 and 9 m s(-1), the tail area decreased linearly with speed, and at speeds above 9 m s(-1) the tail was fully furled. Reynolds number calculated with the mean chord as the reference length ranged from 38 000 to 76 000 over the speed range 6-11 m s(-1). Comparisons of the jackdaw flight performance were made with existing theory of gliding flight. We also re-analysed data on span ratios with respect to speed in two other bird species previously studied in wind tunnels. These data indicate that an equation for calculating the span ratio, which minimises the sum of induced and profile drag, does not predict the actual span ratios observed in these birds. We derive an alternative equation on the basis of the observed span ratios for calculating wingspan and wing area with respect to forward speed in gliding birds from information about body mass, maximum wingspan, maximum wing area and maximum coefficient of lift. These alternative equations can be used in combination with any model of gliding flight where wing area and wingspan are considered to calculate sinking rate with respect to forward speed.

[The analytical setting of rotary speed of centrifuge rotor and centrifugation time in chemical, biochemical and microbiological practice].

PubMed

Zolotarev, K V

2012-08-01

The researchers happen to face with suspensions in their chemical, biochemical and microbiological practice. The suspensions are the disperse systems with solid dispersed phase and liquid dispersion medium and with dispersed phase particle size > 100 nm (10-7 m). Quite often the necessity occurs to separate solid particles from liquid. To use for this purpose the precipitation in gravitation field can make the process to progress too long. In this respect an effective mode is the precipitation in the field of centrifugal forces--the centrifugation. The rotary speed of centrifuge rotor and centrifugation time can be set analytically using regularities of general dynamics and hydrodynamics. To this effect, should be written and transformed the equation of First and Second Newton Laws for suspension particle being in the field of centrifugal forces and forces of resistance of liquid and vessel wall. The force of liquid resistance depends on particle motion condition in liquid. To determine the regimen the Archimedes and Reynolds numerical dimensionless criteria are to be applied. The article demonstrates the results of these transformations as analytical inverse ratio dependence of centrifugation time from rotary speed. The calculation of series of "rate-time" data permits to choose the optimal data pair on the assumption of centrifuge capacity and practical reasonability. The results of calculations are validated by actual experimental data hence the physical mathematical apparatus can be considered as effective one. The setting progress depends both from parameter (Reynolds criterion) and data series calculation. So, the most convenient way to apply this operation is the programming approach. The article proposes to use the program Microsoft Excel and VBA programming language for this purpose. The possibility to download the file from Internet to use it for fast solution is proposed.

Global solar magetic field organization in the extended corona: influence on the solar wind speed and density over the cycle.

NASA Astrophysics Data System (ADS)

Réville, V.; Velli, M.; Brun, S.

2017-12-01

The dynamics of the solar wind depends intrinsically on the structure of the global solar magnetic field, which undergoes fundamental changes over the 11yr solar cycle. For instance, the wind terminal velocity is thought to be anti-correlated with the expansion factor, a measure of how the magnetic field varies with height in the solar corona, usually computed at a fixed height (≈ 2.5 Rȯ, the source surface radius which approximates the distance at which all magnetic field lines become open). However, the magnetic field expansion affects the solar wind in a more detailed way, its influence on the solar wind properties remaining significant well beyond the source surface: we demonstrate this using 3D global MHD simulations of the solar corona, constrained by surface magnetograms over half a solar cycle (1989-2001). For models to comply with the constraints provided by observed characteristics of the solar wind, namely, that the radial magnetic field intensity becomes latitude independent at some distance from the Sun (Ulysses observations beyond 1 AU), and that the terminal wind speed is anti-correlated with the mass flux, they must accurately describe expansion beyond the solar wind critical point (even up to 10Rȯ and higher in our model). We also show that near activity minimum, expansion in the higher corona beyond 2.5 Rȯ is actually the dominant process affecting the wind speed. We discuss the consequences of this result on the necessary acceleration profile of the solar wind, the location of the sonic point and of the energy deposition by Alfvén waves.

A New Framework for Quantifying Lidar Uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newman, Jennifer, F.; Clifton, Andrew; Bonin, Timothy A.

2017-03-24

As wind turbine sizes increase and wind energy expands to more complex and remote sites, remote sensing devices such as lidars are expected to play a key role in wind resource assessment and power performance testing. The switch to remote sensing devices represents a paradigm shift in the way the wind industry typically obtains and interprets measurement data for wind energy. For example, the measurement techniques and sources of uncertainty for a remote sensing device are vastly different from those associated with a cup anemometer on a meteorological tower. Current IEC standards discuss uncertainty due to mounting, calibration, and classificationmore » of the remote sensing device, among other parameters. Values of the uncertainty are typically given as a function of the mean wind speed measured by a reference device. However, real-world experience has shown that lidar performance is highly dependent on atmospheric conditions, such as wind shear, turbulence, and aerosol content. At present, these conditions are not directly incorporated into the estimated uncertainty of a lidar device. In this presentation, we propose the development of a new lidar uncertainty framework that adapts to current flow conditions and more accurately represents the actual uncertainty inherent in lidar measurements under different conditions. In this new framework, sources of uncertainty are identified for estimation of the line-of-sight wind speed and reconstruction of the three-dimensional wind field. These sources are then related to physical processes caused by the atmosphere and lidar operating conditions. The framework is applied to lidar data from an operational wind farm to assess the ability of the framework to predict errors in lidar-measured wind speed.« less

Potential effect of skull thickening on the associations between cognition and brain atrophy in ageing.

PubMed

Aribisala, Benjamin Segun; Royle, Natalie A; Valdés Hernández, Maria C; Murray, Catherine; Penke, Lars; Gow, Alan; Maniega, Susana Muñoz; Starr, John M; Bastin, Mark; Deary, Ian; Wardlaw, Joanna

2014-09-01

intracranial volume (ICV) is commonly used as a marker of premorbid brain size in neuroimaging studies as it is thought to remain fixed throughout adulthood. However, inner skull table thickening would encroach on ICV and could mask actual brain atrophy. we investigated the effect that thickening might have on the associations between brain atrophy and cognition. the sample comprised 57 non-demented older adults who underwent structural brain MRI at mean age 72.7 ± 0.7 years and were assessed on cognitive ability at mean age 11 and 73 years. Principal component analysis was used to derive factors of general cognitive ability (g), information processing speed and memory from the recorded cognitive ability data. The total brain tissue volume and ICV with (estimated original ICV) and without (current ICV) adjusting for the effects of inner table skull thickening were measured. General linear modelling was used to test for associations. all cognitive ability variables were significantly (P < 0.01) associated with percentage total brain volume in ICV measured without adjusting for skull thickening (g: η(2) = 0.177, speed: η(2) = 0.264 and memory: η(2) = 0.132). After accounting for skull thickening, only speed was significantly associated with percentage total brain volume in ICV (η(2) = 0.085, P = 0.034), not g or memory. not accounting for skull thickening when computing ICV can distort the association between brain atrophy and cognitive ability in old age. Larger samples are required to determine the true effect. © The Author 2014. Published by Oxford University Press on behalf of the British Geriatrics Society. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Effect of processing parameters on the corrosion behaviour of friction stir processed AA 2219 aluminum alloy

NASA Astrophysics Data System (ADS)

Surekha, K.; Murty, B. S.; Prasad Rao, K.

2009-04-01

The effect of processing parameters (rotation speed and traverse speed) on the corrosion behaviour of friction stir processed high strength precipitation hardenable AA 2219-T87 alloy was investigated. The results indicate that the rotation speed has a major influence in determining the rate of corrosion, which is attributed to the breaking down and dissolution of the intermetallic particles. Corrosion resistance of friction stir processed alloy was studied by potentiodynamic polarization, electrochemical impedance spectroscopy, salt spray and immersion tests.

European Science Notes. Volume 39, Number 8.

DTIC Science & Technology

1985-08-01

electrophysiological 370 -- , * * ESN 39-8 (1985) slower increment of the speed to the end mus which occurs immediately after the phase . The initial jump is... curve and that removal appears to simple constructions, ease of modula- correspond more closely with the melt tion, and efficient discharge excita- phase ...separate experimental condi- (uncued condition). On some trials the tions. Figure 2 shows the curves for light actually appeared in a location the four

Design of the Bus Interface Unit for the Distributed Processor/Memory System.

DTIC Science & Technology

1976-12-01

microroutine flowchart developed. Once this had been done , a high-speed, flexible microprocessor that would be adapt- able to a hardware...routine) was translated Into microcode and provide the mnemonic code and flowchart , Chapter V summarizes and discusses actual system construction...Fig. 11. This diagram shows that the BIU is driven by Interrupt stimuli which select the beginn ing address of the appropriate microroutine rather

Motor Starters

NASA Technical Reports Server (NTRS)

1986-01-01

The power factor controller (PFC) was invented by a NASA engineer. It matches voltage with a motor's actual need by sensing shifts in the relationship between voltage and current flow. With the device, power can be trimmed as much as 65%. Intellinet adopted this technology and designed "soft start" and "load-responsive" control modes to start engines gradually and recycle voltage without reducing motor speed. Other features are lower motor heat and faster fault identification.

Simple and high-speed polarization-based QKD

NASA Astrophysics Data System (ADS)

Grünenfelder, Fadri; Boaron, Alberto; Rusca, Davide; Martin, Anthony; Zbinden, Hugo

2018-01-01

We present a simplified BB84 protocol with only three quantum states and one decoy-state level. We implement this scheme using the polarization degree of freedom at telecom wavelength. Only one pulsed laser is used in order to reduce possible side-channel attacks. The repetition rate of 625 MHz and the achieved secret bit rate of 23 bps over 200 km of standard fiber are the actual state of the art.

Single-Word Recognition Need Not Depend on Single-Word Features: Narrative Coherence Counteracts Effects of Single-Word Features That Lexical Decision Emphasizes

ERIC Educational Resources Information Center

Teng, Dan W.; Wallot, Sebastian; Kelty-Stephen, Damian G.

2016-01-01

Research on reading comprehension of connected text emphasizes reliance on single-word features that organize a stable, mental lexicon of words and that speed or slow the recognition of each new word. However, the time needed to recognize a word might not actually be as fixed as previous research indicates, and the stability of the mental lexicon…

Zero-Energy Optical Logic: Can It Be Practical?

NASA Astrophysics Data System (ADS)

Caulfield, H. John

The thermodynamic “permission” to build a device that can evaluate a sequence of logic operations that operate at zero energy has existed for about 40 years. That is, physics allows it in principle. Conceptual solutions have been explored ever since then. A great number of important concepts were developed in so doing. Over the last four years, my colleagues and I have explored the possibility of a constructive proof. And we finally succeeded. Somewhat unexpectedly, we found such a proof and found that lossless logic systems could actually be built. And, as we had anticipated, it can only be implemented by optics. That raises a new question: Might an optical zero-energy logic system actually be good enough to displace electronic versions in some cases? In this paper, I do not even try to answer that question, but I do lay out some problems now blocking practical applications and show some promising approaches to solving them. The problems addressed are speed, size, and error rate. The anticipated speed problem simply vanishes, as it was an inference from the implicit assumption that the logic would be electronic. But the other two problems are real and must be addressed if energy-free logic is to have any significant applications. Initial steps in solving the size and error rate are addressed in more detail.

High-Speed Civil Transport Forecast: Simulated Airlines Scenarios for Mach 1.6, Mach 2.0, and Mach 2.4 Configurations for Year 2015

NASA Technical Reports Server (NTRS)

Metwally, Munir

1996-01-01

The report describes the development of a database of fuel burn and emissions from projected High Speed Civil Transport (HSCT) fleets that reflect actual airlines' networks, operational requirement, and traffic flow as operated by simulated world wide airlines for Mach 1.6, 2.0, and 2.4 HSCT configurations. For the year 2015, McDonnell Douglas Corporation created two supersonic commercial air traffic networks consisting of origin-destination city pair routes and associated traffic levels. The first scenario represented a manufacturing upper limit producible HSCT fleet availability by year 2015. The fleet projection of the Mach 2.4 configuration for this scenario was 1059 units with a traffic capture of 70 percent. The second scenario focused on the number of units that can minimally be produced by the year 2015. Using realistic production rates, the HSCT fleet projection amounts to 565 units. The traffic capture associated with this fleet was estimated at 40 percent. The airlines network was extracted from the actual networks of 21 major world airlines. All the routes were screened for suitability for HSCT operations. The route selection criteria included great circle distance, difference between flight path distance and great circle distance to avoid overland operations, and potential flight frequency.

Wind speed vector restoration algorithm

NASA Astrophysics Data System (ADS)

Baranov, Nikolay; Petrov, Gleb; Shiriaev, Ilia

2018-04-01

Impulse wind lidar (IWL) signal processing software developed by JSC «BANS» recovers full wind speed vector by radial projections and provides wind parameters information up to 2 km distance. Increasing accuracy and speed of wind parameters calculation signal processing technics have been studied in this research. Measurements results of IWL and continuous scanning lidar were compared. Also, IWL data processing modeling results have been analyzed.

Processing speed and working memory training in multiple sclerosis: a double-blind randomized controlled pilot study.

PubMed

Hancock, Laura M; Bruce, Jared M; Bruce, Amanda S; Lynch, Sharon G

2015-01-01

Between 40-65% of multiple sclerosis patients experience cognitive deficits, with processing speed and working memory most commonly affected. This pilot study investigated the effect of computerized cognitive training focused on improving processing speed and working memory. Participants were randomized into either an active or a sham training group and engaged in six weeks of training. The active training group improved on a measure of processing speed and attention following cognitive training, and data trended toward significance on measures of other domains. Results provide preliminary evidence that cognitive training with multiple sclerosis patients may produce moderate improvement in select areas of cognitive functioning.

The role of speed versus working memory in predicting learning new information in multiple sclerosis.

PubMed

Chiaravalloti, Nancy D; Stojanovic-Radic, Jelena; DeLuca, John

2013-01-01

The most common cognitive impairments in multiple sclerosis (MS) have been documented in specific domains, including new learning and memory, working memory, and information processing speed. However, little attempt has been made to increase our understanding of their relationship to one another. While recent studies have shown that processing speed impacts new learning and memory abilities in MS, the role of working memory in this relationship has received less attention. The present study examines the relative contribution of impaired working memory versus processing speed in new learning and memory functions in MS. Participants consisted of 51 individuals with clinically definite MS. Participants completed two measures of processing speed, two measures of working memory, and two measures of episodic memory. Data were analyzed via correlational and multiple regression analysis. Results indicate that the variance in new learning abilities in this sample was primarily associated with processing speed, with working memory exerting much less of an influence. Results are discussed in terms of the role of cognitive rehabilitation of new learning and memory abilities in persons with MS.

Higher-order cognitive training effects on processing speed-related neural activity: a randomized trial.

PubMed

Motes, Michael A; Yezhuvath, Uma S; Aslan, Sina; Spence, Jeffrey S; Rypma, Bart; Chapman, Sandra B

2018-02-01

Higher-order cognitive training has shown to enhance performance in older adults, but the neural mechanisms underlying performance enhancement have yet to be fully disambiguated. This randomized trial examined changes in processing speed and processing speed-related neural activity in older participants (57-71 years of age) who underwent cognitive training (CT, N = 12) compared with wait-listed (WLC, N = 15) or exercise-training active (AC, N = 14) controls. The cognitive training taught cognitive control functions of strategic attention, integrative reasoning, and innovation over 12 weeks. All 3 groups worked through a functional magnetic resonance imaging processing speed task during 3 sessions (baseline, mid-training, and post-training). Although all groups showed faster reaction times (RTs) across sessions, the CT group showed a significant increase, and the WLC and AC groups showed significant decreases across sessions in the association between RT and BOLD signal change within the left prefrontal cortex (PFC). Thus, cognitive training led to a change in processing speed-related neural activity where faster processing speed was associated with reduced PFC activation, fitting previously identified neural efficiency profiles. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Blood lactate accumulation in top level swimmers following competition.

PubMed

Bonifazi, M; Martelli, G; Marugo, L; Sardella, F; Carli, G

1993-03-01

The purposes of this study were to evaluate the significance of blood lactate values after competitions and the blood lactate-swimming speed relationship to swimming performances. Auricular blood samples (N = 421) were collected in 203 top level Italian swimmers (116 males and 87 females) at the end of competitions performed in a 25 m swimming pool. The distribution of all lactate values differed between males and females. The lowest lactate values occurred in swimmers performing the longest distances both in males (1500 m) and females (800 m). In swimmers performing freestyle events a relationship between V-4 mM (swimming speed at 4 mmol/l blood lactate value) and competition velocities was observed, in males, at 200, 400 and 1500 m and, in females, at 400 and 800 m. The predicted velocity corresponding to the competition lactate value assessed by the individual blood lactate-swimming speed relationship was found to be highly related to the actual competition velocity. Results suggest that blood lactate values in swimmers are a useful indication of individual aptitudes.

User-controlled photographic animations, photograph-based questions, and questionnaires: three Internet-based instruments for measuring drivers' risk-taking behavior.

PubMed

Horswill, M S; Coster, M E

2001-02-01

The Internet has been exploited successfully in the past as a medium for behavioral research. This paper presents a series of studies designed to assess Internet-based measures of drivers' risk-taking behavior. First, we compared responses from an Internet sample with a traditional pencil-and-paper sample using established questionnaire measures of risk taking. No significant differences were found. Second, we assessed the validity of new Internet-based instruments, involving photographs and photographic animations, that measured speed, gap acceptance, and passing. Responses were found to reflect known demographic patterns of actual behavior to some degree. Also, a roadside survey of speeds was carried out at the locations depicted in the photographic measure of speeding and, with certain exceptions, differences between the two appeared to be constant. Third, a between-subject experimental manipulation involving the photographic animation measure of gap acceptance was used to demonstrate one application of these techniques.

Universal Parameter Measurement and Sensorless Vector Control of Induction and Permanent Magnet Synchronous Motors

NASA Astrophysics Data System (ADS)

Yamamoto, Shu; Ara, Takahiro

Recently, induction motors (IMs) and permanent-magnet synchronous motors (PMSMs) have been used in various industrial drive systems. The features of the hardware device used for controlling the adjustable-speed drive in these motors are almost identical. Despite this, different techniques are generally used for parameter measurement and speed-sensorless control of these motors. If the same technique can be used for parameter measurement and sensorless control, a highly versatile adjustable-speed-drive system can be realized. In this paper, the authors describe a new universal sensorless control technique for both IMs and PMSMs (including salient pole and nonsalient pole machines). A mathematical model applicable for IMs and PMSMs is discussed. Using this model, the authors derive the proposed universal sensorless vector control algorithm on the basis of estimation of the stator flux linkage vector. All the electrical motor parameters are determined by a unified test procedure. The proposed method is implemented on three test machines. The actual driving test results demonstrate the validity of the proposed method.

The Effect of a Low-Speed Automatic Brake System Estimated From Real Life Data

PubMed Central

Isaksson-Hellman, Irene; Lindman, Magdalena

2012-01-01

A substantial part of all traffic accidents involving passenger cars are rear-end collisions and most of them occur at low speed. Auto Brake is a feature that has been launched in several passenger car models during the last few years. City Safety is a technology designed to help the driver mitigate, and in certain situations avoid, rear-end collisions at low speed by automatically braking the vehicle. Studies have been presented that predict promising benefits from these kinds of systems, but few attempts have been made to show the actual effect of Auto Brake. In this study, the effect of City Safety, a standard feature on the Volvo XC60 model, is calculated based on insurance claims data from cars in real traffic crashes in Sweden. The estimated claim frequency of rear-end frontal collisions measured in claims per 1,000 insured vehicle years was 23% lower for the City Safety equipped XC60 model than for other Volvo models without the system. PMID:23169133

Wind power error estimation in resource assessments.

PubMed

Rodríguez, Osvaldo; Del Río, Jesús A; Jaramillo, Oscar A; Martínez, Manuel

2015-01-01

Estimating the power output is one of the elements that determine the techno-economic feasibility of a renewable project. At present, there is a need to develop reliable methods that achieve this goal, thereby contributing to wind power penetration. In this study, we propose a method for wind power error estimation based on the wind speed measurement error, probability density function, and wind turbine power curves. This method uses the actual wind speed data without prior statistical treatment based on 28 wind turbine power curves, which were fitted by Lagrange's method, to calculate the estimate wind power output and the corresponding error propagation. We found that wind speed percentage errors of 10% were propagated into the power output estimates, thereby yielding an error of 5%. The proposed error propagation complements the traditional power resource assessments. The wind power estimation error also allows us to estimate intervals for the power production leveled cost or the investment time return. The implementation of this method increases the reliability of techno-economic resource assessment studies.

Wind Power Error Estimation in Resource Assessments

PubMed Central

Rodríguez, Osvaldo; del Río, Jesús A.; Jaramillo, Oscar A.; Martínez, Manuel

2015-01-01

Estimating the power output is one of the elements that determine the techno-economic feasibility of a renewable project. At present, there is a need to develop reliable methods that achieve this goal, thereby contributing to wind power penetration. In this study, we propose a method for wind power error estimation based on the wind speed measurement error, probability density function, and wind turbine power curves. This method uses the actual wind speed data without prior statistical treatment based on 28 wind turbine power curves, which were fitted by Lagrange's method, to calculate the estimate wind power output and the corresponding error propagation. We found that wind speed percentage errors of 10% were propagated into the power output estimates, thereby yielding an error of 5%. The proposed error propagation complements the traditional power resource assessments. The wind power estimation error also allows us to estimate intervals for the power production leveled cost or the investment time return. The implementation of this method increases the reliability of techno-economic resource assessment studies. PMID:26000444

The effect of a low-speed automatic brake system estimated from real life data.

PubMed

Isaksson-Hellman, Irene; Lindman, Magdalena

2012-01-01

A substantial part of all traffic accidents involving passenger cars are rear-end collisions and most of them occur at low speed. Auto Brake is a feature that has been launched in several passenger car models during the last few years. City Safety is a technology designed to help the driver mitigate, and in certain situations avoid, rear-end collisions at low speed by automatically braking the vehicle.Studies have been presented that predict promising benefits from these kinds of systems, but few attempts have been made to show the actual effect of Auto Brake. In this study, the effect of City Safety, a standard feature on the Volvo XC60 model, is calculated based on insurance claims data from cars in real traffic crashes in Sweden. The estimated claim frequency of rear-end frontal collisions measured in claims per 1,000 insured vehicle years was 23% lower for the City Safety equipped XC60 model than for other Volvo models without the system.

A study of the influence of air-knife tilting on coating thickness in hot-dip galvanizing

NASA Astrophysics Data System (ADS)

Cho, Tae-Seok; Kwon, Young-Doo; Kwon, Soon-Bum

2009-09-01

Gas wiping is a decisive operation in hot-dip galvanizing process. In special, it has a crucial influence on the thickness and uniformity in coating film, but may be subsequently responsible for the problem of splashing. The progress of industry demands continuously the reduction of production costs which may relate directly with the increase of coating speed, and the speed up of coating results in the increase of stagnation pressure in gas wiping system in final. It is known that the increase of stagnation pressure may accompany a harmful problem of splashing in general. Together with these, also, from the view point of energy consumption, it is necessary to design a nozzle optimally. And there is known that the downward tilting of nozzle using in air knife system is effective to prevent in somewhat the harmful problem of splashing. In these connections, first, we design a nozzle with constant expansion rate. Next, for the case of actual coating conditions in field, the effects of tilting of the constant expansion rate nozzle are investigated by numerical analysis. Under the present numerical conditions, it was turned out that the nozzle of constant expansion rate of p = having a downward jet angle of 5° is the most effective to diminish the onset of splashing, while the influence of small tilting of the nozzle on impinging wall pressure itself is not so large.

Optimizing culture conditions for production of intra and extracellular inulinase and invertase from Aspergillus niger ATCC 20611 by response surface methodology (RSM).

PubMed

Dinarvand, Mojdeh; Rezaee, Malahat; Foroughi, Majid

The aim of this study was obtain a model that maximizes growth and production of inulinase and invertase by Aspergillus niger ATCC 20611, employing response surface methodology (RSM). The RSM with a five-variable and three-level central composite design (CCD) was employed to optimize the medium composition. Results showed that the experimental data could be appropriately fitted into a second-order polynomial model with a coefficient of determination (R 2 ) more than 0.90 for all responses. This model adequately explained the data variation and represented the actual relationships between the parameters and responses. The pH and temperature value of the cultivation medium were the most significant variables and the effects of inoculum size and agitation speed were slightly lower. The intra-extracellular inulinase, invertase production and biomass content increased 10-32 fold in the optimized medium condition (pH 6.5, temperature 30°C, 6% (v/v), inoculum size and 150rpm agitation speed) by RSM compared with medium optimized through the one-factor-at-a-time method. The process development and intensification for simultaneous production of intra-extracellular inulinase (exo and endo inulinase) and invertase from A. niger could be used for industrial applications. Copyright © 2017 Sociedade Brasileira de Microbiologia. Published by Elsevier Editora Ltda. All rights reserved.

Evaluating the Properties of Poly(lactic-co-glycolic acid) Nanoparticle Formulations Encapsulating a Hydrophobic Drug by Using the Quality by Design Approach.

PubMed

Kozaki, Masato; Kobayashi, Shin-Ichiro; Goda, Yukihiro; Okuda, Haruhiro; Sakai-Kato, Kumiko

2017-01-01

We applied the Quality by Design (QbD) approach to the development of poly(lactic-co-glycolic acid) (PLGA) nanoparticle formulations encapsulating triamcinolone acetonide, and the critical process parameters (CPPs) were identified to clarify the correlations between critical quality attributes and CPPs. Quality risk management was performed by using an Ishikawa diagram and experiments with a fractional factorial design (ANOVA). The CPPs for particle size were PLGA concentration and rotation speed, and the CPP for relative drug loading efficiency was the poor solvent to good solvent volume ratio. By assessing the mutually related factors in the form of ratios, many factors could be efficiently considered in the risk assessment. We found a two-factor interaction between rotation speed and rate of addition of good solvent by using a fractional factorial design with resolution V. The system was then extended by using a central composite design, and the results obtained were visualized by using the response surface method to construct a design space. Our research represents a case study of the application of the QbD approach to pharmaceutical development, including formulation screening, by taking actual production factors into consideration. Our findings support the feasibility of using a similar approach to nanoparticle formulations under development. We could establish an efficient method of analyzing the CPPs of PLGA nanoparticles by using a QbD approach.

Estimating the time evolution of NMR systems via a quantum-speed-limit-like expression

NASA Astrophysics Data System (ADS)

Villamizar, D. V.; Duzzioni, E. I.; Leal, A. C. S.; Auccaise, R.

2018-05-01

Finding the solutions of the equations that describe the dynamics of a given physical system is crucial in order to obtain important information about its evolution. However, by using estimation theory, it is possible to obtain, under certain limitations, some information on its dynamics. The quantum-speed-limit (QSL) theory was originally used to estimate the shortest time in which a Hamiltonian drives an initial state to a final one for a given fidelity. Using the QSL theory in a slightly different way, we are able to estimate the running time of a given quantum process. For that purpose, we impose the saturation of the Anandan-Aharonov bound in a rotating frame of reference where the state of the system travels slower than in the original frame (laboratory frame). Through this procedure it is possible to estimate the actual evolution time in the laboratory frame of reference with good accuracy when compared to previous methods. Our method is tested successfully to predict the time spent in the evolution of nuclear spins 1/2 and 3/2 in NMR systems. We find that the estimated time according to our method is better than previous approaches by up to four orders of magnitude. One disadvantage of our method is that we need to solve a number of transcendental equations, which increases with the system dimension and parameter discretization used to solve such equations numerically.

Evolution of attention mechanisms for early visual processing

NASA Astrophysics Data System (ADS)

Müller, Thomas; Knoll, Alois

2011-03-01

Early visual processing as a method to speed up computations on visual input data has long been discussed in the computer vision community. The general target of a such approaches is to filter nonrelevant information from the costly higher-level visual processing algorithms. By insertion of this additional filter layer the overall approach can be speeded up without actually changing the visual processing methodology. Being inspired by the layered architecture of the human visual processing apparatus, several approaches for early visual processing have been recently proposed. Most promising in this field is the extraction of a saliency map to determine regions of current attention in the visual field. Such saliency can be computed in a bottom-up manner, i.e. the theory claims that static regions of attention emerge from a certain color footprint, and dynamic regions of attention emerge from connected blobs of textures moving in a uniform way in the visual field. Top-down saliency effects are either unconscious through inherent mechanisms like inhibition-of-return, i.e. within a period of time the attention level paid to a certain region automatically decreases if the properties of that region do not change, or volitional through cognitive feedback, e.g. if an object moves consistently in the visual field. These bottom-up and top-down saliency effects have been implemented and evaluated in a previous computer vision system for the project JAST. In this paper an extension applying evolutionary processes is proposed. The prior vision system utilized multiple threads to analyze the regions of attention delivered from the early processing mechanism. Here, in addition, multiple saliency units are used to produce these regions of attention. All of these saliency units have different parameter-sets. The idea is to let the population of saliency units create regions of attention, then evaluate the results with cognitive feedback and finally apply the genetic mechanism: mutation and cloning of the best performers and extinction of the worst performers considering computation of regions of attention. A fitness function can be derived by evaluating, whether relevant objects are found in the regions created. It can be seen from various experiments, that the approach significantly speeds up visual processing, especially regarding robust ealtime object recognition, compared to an approach not using saliency based preprocessing. Furthermore, the evolutionary algorithm improves the overall performance of the preprocessing system in terms of quality, as the system automatically and autonomously tunes the saliency parameters. The computational overhead produced by periodical clone/delete/mutation operations can be handled well within the realtime constraints of the experimental computer vision system. Nevertheless, limitations apply whenever the visual field does not contain any significant saliency information for some time, but the population still tries to tune the parameters - overfitting avoids generalization in this case and the evolutionary process may be reset by manual intervention.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lechman, Jeremy B.; Battaile, Corbett Chandler.; Bolintineanu, Dan

This report summarizes a project in which the authors sought to develop and deploy: (i) experimental techniques to elucidate the complex, multiscale nature of thermal transport in particle-based materials; and (ii) modeling approaches to address current challenges in predicting performance variability of materials (e.g., identifying and characterizing physical- chemical processes and their couplings across multiple length and time scales, modeling information transfer between scales, and statically and dynamically resolving material structure and its evolution during manufacturing and device performance). Experimentally, several capabilities were successfully advanced. As discussed in Chapter 2 a flash diffusivity capability for measuring homogeneous thermal conductivity ofmore » pyrotechnic powders (and beyond) was advanced; leading to enhanced characterization of pyrotechnic materials and properties impacting component development. Chapter 4 describes success for the first time, although preliminary, in resolving thermal fields at speeds and spatial scales relevant to energetic components. Chapter 7 summarizes the first ever (as far as the authors know) application of TDTR to actual pyrotechnic materials. This is the first attempt to actually characterize these materials at the interfacial scale. On the modeling side, new capabilities in image processing of experimental microstructures and direct numerical simulation on complicated structures were advanced (see Chapters 3 and 5). In addition, modeling work described in Chapter 8 led to improved prediction of interface thermal conductance from first principles calculations. Toward the second point, for a model system of packed particles, significant headway was made in implementing numerical algorithms and collecting data to justify the approach in terms of highlighting the phenomena at play and pointing the way forward in developing and informing the kind of modeling approach originally envisioned (see Chapter 6). In both cases much more remains to be accomplished.« less

Effect of Blade Cutout on Power Required by Helicopters Operating at High Tip-Speed Ratios

NASA Technical Reports Server (NTRS)

Gessow, Alfred; Gustafson, F. B.

1960-01-01

A numerical study was made of the effects of blade cutout on the power required by a sample helicopter rotor traveling at tip-speed ratios of 0.3, 0.4, and 0.5. The amount of cutout varied from 0 to 0.5 of the rotor radius and the calculations were carried out for a thrust coefficient-solidity ratio of 0.04. In these calculations the blade within the cutout radius was assumed to have zero chord. The effect of such cutout on profile-drag power ranged from almost no effect at a tip-speed ratio of 0.3 to as much as a 60 percent reduction at a tip-speed ratio of 0.5. Optimum cutout was about 0.3 of the rotor radius. Part of the large power reduction at a tip-speed ratio of 0.5 resulted from a reduction in tip-region stall, brought about by cutout. For tip-speed ratios greater than 0.3, cutout also effected a significant increase in the ability of the rotor to overcome helicopter parasite drag. It is thus seen that the adverse trends (at high tip-speed ratios) indicated by the uniform-chord theoretical charts are caused in large measure by the center portion of the rotor. The extent to which a modified-design rotor can actually be made more efficient at high speeds than a uniform-chord rotor will depend in practice on the degree of success in minimizing the blade plan form near the center and on special modifications in center-section profiles. A few suggestions and estimates in regard to such modifications are included herein.

Fast femtosecond laser ablation for efficient cutting of sintered alumina substrates

NASA Astrophysics Data System (ADS)

Oosterbeek, Reece N.; Ward, Thomas; Ashforth, Simon; Bodley, Owen; Rodda, Andrew E.; Simpson, M. Cather

2016-09-01

Fast, accurate cutting of technical ceramics is a significant technological challenge because of these materials' typical high mechanical strength and thermal resistance. Femtosecond pulsed lasers offer significant promise for meeting this challenge. Femtosecond pulses can machine nearly any material with small kerf and little to no collateral damage to the surrounding material. The main drawback to femtosecond laser machining of ceramics is slow processing speed. In this work we report on the improvement of femtosecond laser cutting of sintered alumina substrates through optimisation of laser processing parameters. The femtosecond laser ablation thresholds for sintered alumina were measured using the diagonal scan method. Incubation effects were found to fit a defect accumulation model, with Fth,1=6.0 J/cm2 (±0.3) and Fth,∞=2.5 J/cm2 (±0.2). The focal length and depth, laser power, number of passes, and material translation speed were optimised for ablation speed and high quality. Optimal conditions of 500 mW power, 100 mm focal length, 2000 μm/s material translation speed, with 14 passes, produced complete cutting of the alumina substrate at an overall processing speed of 143 μm/s - more than 4 times faster than the maximum reported overall processing speed previously achieved by Wang et al. [1]. This process significantly increases processing speeds of alumina substrates, thereby reducing costs, making femtosecond laser machining a more viable option for industrial users.

Information processing speed and 8-year mortality among community-dwelling elderly Japanese.

PubMed

Iwasa, Hajime; Kai, Ichiro; Yoshida, Yuko; Suzuki, Takao; Kim, Hunkyung; Yoshida, Hideyo

2014-01-01

Cognitive function is an important contributor to health among elderly adults. One reliable measure of cognitive functioning is information processing speed, which can predict incident dementia and is longitudinally related to the incidence of functional dependence. Few studies have examined the association between information processing speed and mortality. This 8-year prospective cohort study design with mortality surveillance examined the longitudinal relationship between information processing speed and all-cause mortality among community-dwelling elderly Japanese. A total of 440 men and 371 women aged 70 years or older participated in this study. The Digit Symbol Substitution Test (DSST) was used to assess information processing speed. DSST score was used as an independent variable, and age, sex, education level, depressive symptoms, chronic disease, sensory deficit, instrumental activities of daily living, walking speed, and cognitive impairment were used as covariates. During the follow-up period, 182 participants (133 men and 49 women) died. A multivariate Cox proportional hazards model showed that lower DSST score was associated with increased risk of mortality (hazard ratio [HR] = 1.62, 95% CI = 0.97-2.72; HR = 1.73, 95% CI = 1.05-2.87; and HR = 2.55, 95% CI = 1.51-4.29, for the third, second, and first quartiles of DSST score, respectively). Slower information processing speed was associated with shorter survival among elderly Japanese.

A single aerobic exercise session accelerates movement execution but not central processing.

PubMed

Beyer, Kit B; Sage, Michael D; Staines, W Richard; Middleton, Laura E; McIlroy, William E

2017-03-27

Previous research has demonstrated that aerobic exercise has disparate effects on speed of processing and movement execution. In simple and choice reaction tasks, aerobic exercise appears to increase speed of movement execution while speed of processing is unaffected. In the flanker task, aerobic exercise has been shown to reduce response time on incongruent trials more than congruent trials, purportedly reflecting a selective influence on speed of processing related to cognitive control. However, it is unclear how changes in speed of processing and movement execution contribute to these exercise-induced changes in response time during the flanker task. This study examined how a single session of aerobic exercise influences speed of processing and movement execution during a flanker task using electromyography to partition response time into reaction time and movement time, respectively. Movement time decreased during aerobic exercise regardless of flanker congruence but returned to pre-exercise levels immediately after exercise. Reaction time during incongruent flanker trials decreased over time in both an aerobic exercise and non-exercise control condition indicating it was not specifically influenced by exercise. This disparate influence of aerobic exercise on movement time and reaction time indicates the importance of partitioning response time when examining the influence of aerobic exercise on speed of processing. The decrease in reaction time over time independent of aerobic exercise indicates that interpreting pre-to-post exercise changes in behavior requires caution. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

White matter and information processing speed following treatment with cranial-spinal radiation for pediatric brain tumor.

PubMed

Scantlebury, Nadia; Bouffet, Eric; Laughlin, Suzanne; Strother, Douglas; McConnell, Dina; Hukin, Juliette; Fryer, Christopher; Laperriere, Normand; Montour-Proulx, Isabelle; Keene, Daniel; Fleming, Adam; Jabado, Nada; Liu, Fang; Riggs, Lily; Law, Nicole; Mabbott, Donald J

2016-05-01

We compared the structure of specific white matter tracts and information processing speed between children treated for posterior fossa tumors with cranial-spinal radiation (n = 30), or with surgery +/- focal radiation (n = 29), and healthy children (n = 37). Probabilistic diffusion tensor imaging (DTI) tractography was used to delineate the inferior longitudinal fasciculi, optic radiation, inferior frontal occipital fasciculi, and uncinate fasciculi bilaterally. Information processing speed was measured using the coding and symbol search subtests of the Wechsler Intelligence Scales, and visual matching, pair cancellation, and rapid picture naming subtests of the Woodcock-Johnson Test of Cognitive Ability, 3rd revision. We examined group differences using repeated measures MANOVAs and path analyses were used to test the relations between treatment, white matter structure of the tracts, and information processing speed. DTI indices of the optic radiations, the inferior longitudinal fasciculi, and the inferior fronto-occipital fasciculi differed between children treated with cranial-spinal radiation and children treated with surgery +/- focal radiation, and healthy controls (p = .045). Children treated with cranial-spinal radiation also exhibited lower processing speed scores relative to healthy control subjects (p = .002). Notably, we observed that group differences in information processing speed were related to the structure of the right optic radiation (p = .002). We show that cranial-spinal radiation may have a negative impact on information processing speed via insult to the right optic radiations. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Between-person and within-person associations among processing speed, attention switching, and working memory in younger and older adults.

PubMed

Stawski, Robert S; Sliwinski, Martin J; Hofer, Scott M

2013-01-01

BACKGROUND/STUDY CONTEXT: Theories of cognitive aging predict associations among processes that transpire within individuals, but are often tested by examining between-person relationships. The authors provide an empirical demonstration of how associations among measures of processing speed, attention switching, and working memory are different when considered between persons versus within persons over time. A sample of 108 older adults (M (age) = 80.8, range = 66-95) and 68 younger adults (M (age) = 20.2, range = 18-24) completed measures of processing speed, attention switching, and working memory on six occasions over a 14-day period. Multilevel modeling was used to examine processing speed and attention switching performance as predictors of working memory performance simultaneously across days (within-person) and across individuals (between-person). The findings indicates that simple comparison and response speed predicted working memory better than attention switching between persons, whereas attention switching predicted working memory better than simple comparison and response speed within persons over time. Furthermore, the authors did not observe strong evidence of age differences in these associations either within or between persons. The findings of the current study suggest that processing speed is important for understanding between-person and age-related differences in working memory, whereas attention switching is more important for understanding within-person variation in working memory. The authors conclude that theories of cognitive aging should be evaluated by analysis of within-person processes, not exclusively age-related individual differences.

Between-Person and Within-Person Associations among Processing Speed, Attention Switching and Working Memory in Younger and Older Adults

PubMed Central

Stawski, Robert S.; Sliwinski, Martin J.; Hofer, Scott M.

2013-01-01

Background/Study Context Theories of cognitive aging predict associations among processes that transpire within individuals, but are often tested by examining between-person relationships. The authors provide an empirical demonstration of how associations among measures of processing speed, attention switching, and working memory are different when considered between persons versus within persons over time. Methods A sample of 108 older adults (Mage: 80.8, range: 66–95) and 68 younger adults (Mage: 20.2, range:18–24) completed measures of processing speed, attention switching, and working memory on six occasions over a 14-day period. Multilevel modeling was used to examine processing speed and attention switching performance as predictors of working memory performance simultaneously across days (within-person) and across individuals (between-person). Results The findings indicates that simple comparison and response speed predicted working memory better than attention switching between persons, whereas attention switching predicted working memory better than simple comparison and response speed within persons over time. Furthermore, the authors did not observe strong evidence of age differences in these associations either within or between persons. Conclusion The findings of the current study suggest that processing speed is important for understanding between-person and age-related differences in working memory, whereas attention switching is more important for understanding within-person variation in working memory. The authors conclude that theories of cognitive aging should be evaluated by analysis of within-person processes, not exclusively age-related individual differences. PMID:23421639

Study on Finite Element Method of Stress Field in Aluminum Alloy High-Speed Milling Process

NASA Astrophysics Data System (ADS)

Zhang, Wei; Li, Shunming; Wu, Qijun; An, Zenghui

2017-11-01

Three-dimensional numerical simulation model has been built by means of Advantage FEM. Perform simulation the stress fields of 7050-T7451 aluminum alloy in high speed milling process at the speed range of 628 m/min∼5946 m/min. The dynamic change and speed’s influence of stress fields and residual stress in machined layer is systematically analyzed. Some conclusions were drawn. With the cutting process development, the stress field converts to the stress state that crushing stress occupies a leading position. The magnitudes of crushing stress in all directions reduce with milling processes as the effect of Thermal-Mechanical-Coupled weakens; With the cutting speed increasing the magnitudes of crushing stress in all directions fluctuate near -950Mpa first, and then increase at the speed of 3000m/min; The residual pulling stress beneath the surface 0.03mm has been found and the magnitude increases with the cutting speed. A good agreement was obtained between predictions and experiments.

White Matter Fractional Anisotropy Correlates With Speed of Processing and Motor Speed in Young Childhood Cancer Survivors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aukema, Eline J.; Caan, Matthan W.A.; Delft University of Technology, Delft

2009-07-01

Purpose: To determine whether childhood medulloblastoma and acute lymphoblastic leukemia (ALL) survivors have decreased white matter fractional anisotropy (WMFA) and whether WMFA is related to the speed of processing and motor speed. Methods and Materials: For this study, 17 patients (6 medulloblastoma, 5 ALL treated with high-dose methotrexate (MTX) (4 x 5 g/m{sup 2}) and 6 with low-dose MTX (3 x 2 g/m{sup 2})) and 17 age-matched controls participated. On a 3.0-T magnetic resonance imaging (MRI) scanner, diffusion tensor imaging (DTI) was performed, and WMFA values were calculated, including specific regions of interest (ROIs), and correlated with the speed ofmore » processing and motor speed. Results: Mean WMFA in the patient group, mean age 14 years (range 8.9 - 16.9), was decreased compared with the control group (p = 0.01), as well as WMFA in the right inferior fronto-occipital fasciliculus (IFO) (p = 0.03) and in the genu of the corpus callosum (gCC) (p = 0.01). Based on neurocognitive results, significant positive correlations were present between processing speed and WMFA in the splenium (sCC) (r = 0.53, p = 0.03) and the body of the corpus callosum (bCC) (r = 0.52, p = 0.03), whereas the right IFO WMFA was related to motor speed (r = 0.49, p < 0.05). Conclusions: White matter tracts, using a 3.0-T MRI scanner, show impairment in childhood cancer survivors, medulloblastoma survivors, and also those treated with high doses of MTX. In particular, white matter tracts in the sCC, bCC and right IFO are positively correlated with speed of processing and motor speed.« less

Research and development of a control system for multi axis cooperative motion based on PMAC

NASA Astrophysics Data System (ADS)

Guo, Xiao-xiao; Dong, Deng-feng; Zhou, Wei-hu

2017-10-01

Based on Programmable Multi-axes Controller (PMAC), a design of a multi axis motion control system for the simulator of spatial targets' dynamic optical properties is proposed. According to analysis the properties of spatial targets' simulator motion control system, using IPC as the main control layer, TurboPMAC2 as the control layer to meet coordinated motion control, data acquisition and analog output. A simulator using 5 servomotors which is connected with speed reducers to drive the output axis was implemented to simulate the motion of both the sun and the space target. Based on PMAC using PID and a notch filter algorithm, negative feedback, the speed and acceleration feed forward algorithm to satisfy the axis' requirements of the good stability and high precision at low speeds. In the actual system, it shows that the velocity precision is higher than 0.04 s ° and the precision of repetitive positioning is better than 0.006° when each axis is at a low-speed. Besides, the system achieves the control function of multi axis coordinated motion. The design provides an important technical support for detecting spatial targets, also promoting the theoretical research.

Evaluation Experiment of Ultrasound Computed Tomography for the Abdominal Sound Speed Imaging

NASA Astrophysics Data System (ADS)

Nogami, Keisuke; Yamada, Akira

2007-07-01

Abdominal sound speed tomographic imaging using through-transmission travel time data on the body surface was investigated. To this end, a hundred kHz range low-frequency wave was used to reduce the wave attenuation within an inner body medium. A method was investigated for the reconstruction of the image with the smallest possible number of path data around the abdominal surface. Specifically, the data from a strong scattering spinal cord should be avoided. To fulfill the requirement, the smoothed path algebraic reconstruction technique was introduced. The validity of this method was examined both on the numerically synthesized data and the experimentally measured data for the phantom specimen and actual human subject. It was shown that an abdominal tomographic sound speed image could be successfully obtained by preparing only 32 transducer locations at the circumference around the abdominal surface and their combination of less than 100 number of observation path data as well as by avoiding the data intersecting the spinal cord. In addition, fat regions were extracted having a sound speed lower than the threshold value to demonstrate the possibility of this method for metabolic syndrome diagnosis.

Performance of a 16.6 Meter Diameter Cross Parachute in a Simulated Martian Environment

NASA Technical Reports Server (NTRS)

Lundstrom, Reginald R.; Darnell, Wayne L.; Coltrane, Lucille C.

1968-01-01

Inflation and drag characteristics of a 54.4-foot (16.6 meter) nominal-diameter cross parachute, deployed at a Mach number of 1.65 and a dynamic pressure of 12.68 lb/sq f t (607.1 N/m(exp2)), were obtained from the fourth balloon-launched flight test of the Planetary Entry Parachute Program (PEPP). After deployment, the parachute quickly inflated to a full condition, partially collapsed, and then gradually reinflated while undergoing rapid oscillations between over-inflation and under-inflation. The oscillations began while the parachute was still at supersonic speeds and continued to low subsonic speeds well below an altitude of 90,000 feet (27.4 km). These canopy instabilities produced large cyclic variations in the parachute's drag coefficient. The average value of drag coefficient was about 0.8 to 0.9 at subsonic speeds and slightly lower at supersonic speeds. These drag coefficient values were based on the actual fabric surface area of the parachute canopy. The parachute sustained minor damage consisting of two canopy tears and abrasions and tears on the riser line. It is believed that this damage did not produce a significant change in the performance of the parachute.

Spatial variability of chilling temperature in Turkey and its effect on human comfort

NASA Astrophysics Data System (ADS)

Toros, H.; Deniz, A.; Şaylan, L.; Şen, O.; Baloğlu, M.

2005-03-01

Air temperature, absolute humidity and wind speed are the most important meteorological parameters that affect human thermal comfort. Because of heat loss, the human body feels air temperatures different to actual temperatures. Wind speed is the most practical element for consideration in terms of human comfort. In winter, due to the strong wind speeds, the sensible temperature is generally colder than the air temperature. This uncomfortable condition can cause problems related to tourism, heating and cooling. In this study, the spatial and temporal distributions of cooling temperatures and Wind Chill Index (WCI) are analyzed for Turkey, and their effect on the human body is considered. In this paper, monthly cooling temperatures between October and March in the years 1929 to 1990 are calculated by using measured temperature and wind speed at 79 stations in Turkey. The influence of wind chill is especially observed in the regions of the Aegean, west and middle Black Sea and east and central Anatolia. The wind chill in these regions has an uncomfortable effect on the human body. Usually, the WCI value is higher in western, northern and central Anatolia than in other regions.

Does order and timing in performance of imagined and actual movements affect the motor imagery process? The duration of walking and writing task.

PubMed

Papaxanthis, Charalambos; Pozzo, Thierry; Skoura, Xanthi; Schieppati, Marco

2002-08-21

The purpose of the present study was to investigate the effects on the duration of imagined movements of changes in timing and order of performance of actual and imagined movement. Two groups of subjects had to actually execute and imagine a walking and a writing task. The first group first executed 10 trials of the actual movements (block A) and then imagined the same movements at different intervals: immediately after actual movements (block I-1) and after 25 min (I-2), 50 min (I-3) and 75 min (I-4) interval. The second group first imagined and then actually executed the tasks. The duration of actual and imagined movements, recorded by means of an electronic stopwatch operated by the subjects, was analysed. The duration of imagined movements was very similar to those of actual movements, for both tasks, regardless of either the interval elapsed from the actual movements (first group) or the order of performance (second group). However, the variability of imagined movement duration was significantly increased compared to variability of the actual movements, for both motor tasks and groups. The findings give evidence of similar cognitive processes underlying both imagination and actual performance of movement. Copyright 2002 Elsevier Science B.V.

Verbal fluency in male and female schizophrenia patients: Different patterns of association with processing speed, working memory span, and clinical symptoms.

PubMed

Brébion, Gildas; Stephan-Otto, Christian; Ochoa, Susana; Nieto, Lourdes; Contel, Montserrat; Usall, Judith

2018-01-01

Decreased processing speed in schizophrenia patients has been identified as a major impairment factor in various neuropsychological domains. Working memory span has been found to be involved in several deep or effortful cognitive processes. We investigated the impact that these 2 cognitive functions may have on phonological and semantic fluency in schizophrenia patients and healthy participants. Fifty-five patients with schizophrenia and 60 healthy participants were administered a neuropsychological battery including phonological and semantic fluency, working memory, and cognitive and motor speed. Regression analyses revealed that motor speed was related to phonological fluency in female patients, whereas cognitive speed was related to semantic fluency in male patients. In addition, working memory span was related to verbal fluency in women from both the patient and the healthy control groups. Decreased processing speed, but not decreased working memory span, accounted for the verbal fluency deficit in patients. Verbal fluency was inversely related to attention deficit in female patients and to negative symptoms in male patients. Decreased processing speed may be the main factor in verbal fluency impairment of patients. Further, the cognitive and clinical predictors of verbal fluency efficiency are different in men and women. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Daily reference crop evapotranspiration with reduced data sets in the humid environments of Azores islands using estimates of actual vapor pressure, solar radiation, and wind speed

NASA Astrophysics Data System (ADS)

Paredes, P.; Fontes, J. C.; Azevedo, E. B.; Pereira, L. S.

2017-11-01

Reference crop evapotranspiration (ETo) estimations using the FAO Penman-Monteith equation (PM-ETo) require a set of weather data including maximum and minimum air temperatures (T max, T min), actual vapor pressure (e a), solar radiation (R s), and wind speed (u 2). However, those data are often not available, or data sets are incomplete due to missing values. A set of procedures were proposed in FAO56 (Allen et al. 1998) to overcome these limitations, and which accuracy for estimating daily ETo in the humid climate of Azores islands is assessed in this study. Results show that after locally and seasonally calibrating the temperature adjustment factor a d used for dew point temperature (T dew) computation from mean temperature, ETo estimations shown small bias and small RMSE ranging from 0.15 to 0.53 mm day-1. When R s data are missing, their estimation from the temperature difference (T max-T min), using a locally and seasonal calibrated radiation adjustment coefficient (k Rs), yielded highly accurate ETo estimates, with RMSE averaging 0.41 mm day-1 and ranging from 0.33 to 0.58 mm day-1. If wind speed observations are missing, the use of the default u 2 = 2 m s-1, or 3 m s-1 in case of weather measurements over clipped grass in airports, revealed appropriated even for the windy locations (u 2 > 4 m s-1), with RMSE < 0.36 mm day-1. The appropriateness of procedure to estimating the missing values of e a, R s, and u 2 was confirmed.

Gigantic Cosmic Corkscrew Reveals New Details About Mysterious Microquasar

NASA Astrophysics Data System (ADS)

2004-10-01

Making an extra effort to image a faint, gigantic corkscrew traced by fast protons and electrons shot out from a mysterious microquasar paid off for a pair of astrophysicists who gained new insights into the beast's inner workings and also resolved a longstanding dispute over the object's distance. Microquasar SS 433 VLA Image of Microquasar SS 433 CREDIT: Blundell & Bowler, NRAO/AUI/NSF (Click on Image for Larger Version) The astrophysicists used the National Science Foundation's Very Large Array (VLA) radio telescope to capture the faintest details yet seen in the plasma jets emerging from the microquasar SS 433, an object once dubbed the "enigma of the century." As a result, they have changed scientists' understanding of the jets and settled the controversy over its distance "beyond all reasonable doubt," they said. SS 433 is a neutron star or black hole orbited by a "normal" companion star. The powerful gravity of the neutron star or black hole draws material from the stellar wind of its companion into an accretion disk of material tightly circling the dense central object prior to being pulled onto it. This disk propels jets of fast protons and electrons outward from its poles at about a quarter of the speed of light. The disk in SS 433 wobbles like a child's top, causing its jets to trace a corkscrew in the sky every 162 days. The new VLA study indicates that the speed of the ejected particles varies over time, contrary to the traditional model for SS 433. "We found that the actual speed varies between 24 percent to 28 percent of light speed, as opposed to staying constant," said Katherine Blundell, of the University of Oxford in the United Kingdom. "Amazingly, the jets going in both directions change their speeds simultaneously, producing identical speeds in both directions at any given time," Blundell added. Blundell worked with Michael Bowler, also of Oxford. The scientists' findings have been accepted by the Astrophysical Journal Letters. SS 433 New VLA Image of SS 433: Red-and-Blue Line Shows Path of Constant-Speed Jets. Note Poor Match of Path to Image. CREDIT: Blundell & Bowler, NRAO/AUI/NSF SS 433 Same Image, With Colored Beads Representing Particle Ejections at Different Speeds. Particle Path Now Matches. CREDIT: Blundell & Bowler, NRAO/AUI/NSF Click Here for Page of Full-Sized Graphics The new VLA image shows two full turns of the jets' corkscrew on both sides of the core. Analyzing the image showed that if material came from the core at a constant speed, the jet paths would not accurately match the details of the image. "By simulating ejections at varying speeds, we were able to produce an exact match to the observed structure," Blundell explained. The scientists first did their match to one of the jets. "We then were stunned to see that the varying speeds that matched the structure of one jet also exactly reproduced the other jet's path," Blundell said. Matching the speeds in the two jets reproduced the observed structure even allowing for the fact that, because one jet is moving more nearly away from us than the other, it takes light longer to reach us from it, she added. The astrophysicists speculate that the changes in ejection speed may be caused by changes in the rate at which material is transferred from the companion star onto the accretion disk. The detailed new VLA image also allowed the astrophysicists to determine that SS 433 is nearly 18,000 light-years distant from Earth. Earlier estimates had the object, in the constellation Aquila, as near as 10,000 light-years. An accurate distance, the scientists said, now allows them to better determine the age of the shell of debris blown out by the supernova explosion that created the dense, compact object in the microquasar. Knowing the distance accurately also allows them to measure the actual brightness of the microquasar's components, and this, they said, improves their understanding of the physical processes at work in the system. The breakthrough image was made using 10 hours of observing time with the VLA in a configuration that maximizes the VLA's ability to see fine detail. It represents the longest "time exposure" of SS 433 at radio wavelengths, and thus shows the faintest details. It also represents the best such image that can be done with current technology. Because the jets in SS 433 are moving, their image would be "smeared" in a longer observation. In order to see even fainter details in the jets, the astrophysicists must await the greater sensitivity of the Expanded VLA, set to become available in a few years. SS 433 was the first example of what now are termed microquasars, binary systems with either a neutron star or black hole orbited by another star, and emitting jets of material at high speeds. The strange stellar system received a wealth of media coverage in the late 1970s and early 1980s. A 1981 Sky & Telescope article was entitled, "SS 433 -- Enigma of the Century." Because microquasars in our own Milky Way Galaxy are thought to produce their high-speed jets of material through processes similar to those that produce jets from the cores of galaxies, the nearby microquasars serve as a convenient "laboratory" for studying the physics of jets. The microquasars are closer and show changes more quickly than their larger cousins. Katherine Blundell is a University Research Fellow funded by the UK's Royal Society. The National Radio Astronomy Observatory is a facility of the National Science Foundation, operated under cooperative agreement by Associated Universities, Inc.

Natural roller bearing fault detection by angular measurement of true instantaneous angular speed

NASA Astrophysics Data System (ADS)

Renaudin, L.; Bonnardot, F.; Musy, O.; Doray, J. B.; Rémond, D.

2010-10-01

The challenge in many production activities involving large mechanical devices like power transmissions consists in reducing the machine downtime, in managing repairs and in improving operating time. Most online monitoring systems are based on conventional vibration measurement devices for gear transmissions or bearings in mechanical components. In this paper, we propose an alternative way of bearing condition monitoring based on the instantaneous angular speed measurement. By the help of a large experimental investigation on two different applications, we prove that localized faults like pitting in bearing generate small angular speed fluctuations which are measurable with optical or magnetic encoders. We also emphasize the benefits of measuring instantaneous angular speed with the pulse timing method through an implicit angular sampling which ensures insensitivity to speed fluctuation. A wide range of operating conditions have been tested for the two applications with varying speed, load, external excitations, gear ratio, etc. The tests performed on an automotive gearbox or on actual operating vehicle wheels also establish the robustness of the proposed methodology. By the means of a conventional Fourier transform, angular frequency channels kinematically related to the fault periodicity show significant magnitude differences related to the damage severity. Sideband effects are evidently seen when the fault is located on rotating parts of the bearing due to load modulation. Additionally, slip effects are also suspected to be at the origin of enlargement of spectrum peaks in the case of double row bearings loaded in a pure radial direction.

Effects of developer exhaustion on the sensitometric properties of four dental films.

PubMed

Syriopoulos, K; Velders, X L; Sanderink, G C; van Ginkel, F C; van der Stelt, P F

1999-03-01

To examine the effects of exhaustion of five different processing solutions on the sensitometric properties of four dental X-ray films: Ektaspeed Plus and Ultra-speed (Kodak Eastman Co. Rochester, USA) and new and previous Dentus M2 (Agfa-Gevaert, Mortsel, Belgium). An aluminum stepwedge was used to construct characteristic curves for the four films. All films were processed manually using three sets of chemicals for manual processing: Agfa (Heraeus Kulzer, Dormagen, Germany), Kodak (Kodak-Pathé, Paris, France) and Demat (Viscopac, Athens, Greece) and two sets for automatic processing: Dürr XR and Periomat (Dürr Dental, Bietigheim-Bissingen, Germany). Film speed and gradient were evaluated until the chemicals were completely exhausted. An analysis of variance was performed separately for each set of chemicals for manual and automatic processing. Ektaspeed Plus was the fastest film in the manual processing solutions. The new Dentus M2 and Ektaspeed Plus films had similar speed using the chemicals for automatic processing. Ultra-speed had the lowest speed in all solutions, but it had the greatest consistency. Exhaustion of the developer caused a comparable decrease in speed of Ektaspeed Plus and the two Dentus M2 films. In fresh chemistry Agfa was the strongest manual processing solution, but it had the highest exhaustion rate. The Dürr XR chemical was stronger than Periomat over the whole test period. The combination of film and processing solution is an important factor for achieving constant sensitometric properties. Ektaspeed Plus and the new Dentus M2 film should be used in dental practice, as they require lower exposure and have equivalent or superior properties compared with Ultra-speed.

Evaluation of the lubrication mechanism at various rotation speeds and granule filling levels in a container mixer using a thermal effusivity sensor.

PubMed

Uchiyama, Jumpei; Aoki, Shigeru

2015-01-01

To research the detailed mechanism of the lubrication process using the thermal effusivity sensor, the relationships of the lubrication progress with the pattern of powder flow, the rotation speed and the filling level were investigated. The thermal effusivity profile was studied as a function of the number of rotations at various rotation speeds. It was observed that at lower rotation speeds, the profiles of the lubrication progress were almost the same, regardless of the rotation speed. In this region, the highest speed was defined as the critical rotation speed (CRS), which was found to be one of the important factors. The CRS had close relations with avalanche flow in the blender. The first and the second phases were observed in the lubrication process. The first phase was influenced by the CRS and the filling level in the blender. The second phase was influenced by the rotation speed. The mechanism of two-phase process was proposed as a macro progression of the dispersion of the lubricant (first phase) and micro progression of the coating of the powder particles with lubricant (second phase). The accurate monitoring by the thermal effusivity sensor was able to help a better understanding in the lubrication process.

First and second order semi-Markov chains for wind speed modeling

NASA Astrophysics Data System (ADS)

Prattico, F.; Petroni, F.; D'Amico, G.

2012-04-01

The increasing interest in renewable energy leads scientific research to find a better way to recover most of the available energy. Particularly, the maximum energy recoverable from wind is equal to 59.3% of that available (Betz law) at a specific pitch angle and when the ratio between the wind speed in output and in input is equal to 1/3. The pitch angle is the angle formed between the airfoil of the blade of the wind turbine and the wind direction. Old turbine and a lot of that actually marketed, in fact, have always the same invariant geometry of the airfoil. This causes that wind turbines will work with an efficiency that is lower than 59.3%. New generation wind turbines, instead, have a system to variate the pitch angle by rotating the blades. This system able the wind turbines to recover, at different wind speed, always the maximum energy, working in Betz limit at different speed ratios. A powerful system control of the pitch angle allows the wind turbine to recover better the energy in transient regime. A good stochastic model for wind speed is then needed to help both the optimization of turbine design and to assist the system control to predict the value of the wind speed to positioning the blades quickly and correctly. The possibility to have synthetic data of wind speed is a powerful instrument to assist designer to verify the structures of the wind turbines or to estimate the energy recoverable from a specific site. To generate synthetic data, Markov chains of first or higher order are often used [1,2,3]. In particular in [3] is presented a comparison between a first-order Markov chain and a second-order Markov chain. A similar work, but only for the first-order Markov chain, is conduced by [2], presenting the probability transition matrix and comparing the energy spectral density and autocorrelation of real and synthetic wind speed data. A tentative to modeling and to join speed and direction of wind is presented in [1], by using two models, first-order Markov chain with different number of states, and Weibull distribution. All this model use Markov chains to generate synthetic wind speed time series but the search for a better model is still open. Approaching this issue, we applied new models which are generalization of Markov models. More precisely we applied semi-Markov models to generate synthetic wind speed time series. Semi-Markov processes (SMP) are a wide class of stochastic processes which generalize at the same time both Markov chains and renewal processes. Their main advantage is that of using whatever type of waiting time distribution for modeling the time to have a transition from one state to another one. This major flexibility has a price to pay: availability of data to estimate the parameters of the model which are more numerous. Data availability is not an issue in wind speed studies, therefore, semi-Markov models can be used in a statistical efficient way. In this work we present three different semi-Markov chain models: the first one is a first-order SMP where the transition probabilities from two speed states (at time Tn and Tn-1) depend on the initial state (the state at Tn-1), final state (the state at Tn) and on the waiting time (given by t=Tn-Tn-1), the second model is a second order SMP where we consider the transition probabilities as depending also on the state the wind speed was before the initial state (which is the state at Tn-2) and the last one is still a second order SMP where the transition probabilities depends on the three states at Tn-2,Tn-1 and Tn and on the waiting times t_1=Tn-1-Tn-2 and t_2=Tn-Tn-1. The three models are used to generate synthetic time series for wind speed by means of Monte Carlo simulations and the time lagged autocorrelation is used to compare statistical properties of the proposed models with those of real data and also with a time series generated though a simple Markov chain. [1] F. Youcef Ettoumi, H. Sauvageot, A.-E.-H. Adane, Statistical bivariate modeling of wind using first-order Markov chain and Weibull distribution, Renewable Energy, 28/2003 1787-1802. [2] A. Shamshad, M.A. Bawadi, W.M.W. Wan Hussin, T.A. Majid, S.A.M. Sanusi, First and second order Markov chain models for synthetic generation of wind speed time series, Energy 30/2005 693-708. [3] H. Nfaoui, H. Essiarab, A.A.M. Sayigh, A stochastic Markov chain model for simulating wind speed time series at Tangiers, Morocco, Renewable Energy 29/2004, 1407-1418.

Exploring "fringe" consciousness: the subjective experience of perceptual fluency and its objective bases.

PubMed

Reber, Rolf; Wurtz, Pascal; Zimmermann, Thomas D

2004-03-01

Perceptual fluency is the subjective experience of ease with which an incoming stimulus is processed. Although perceptual fluency is assessed by speed of processing, it remains unclear how objective speed is related to subjective experiences of fluency. We present evidence that speed at different stages of the perceptual process contributes to perceptual fluency. In an experiment, figure-ground contrast influenced detection of briefly presented words, but not their identification at longer exposure durations. Conversely, font in which the word was written influenced identification, but not detection. Both contrast and font influenced subjective fluency. These findings suggest that speed of processing at different stages condensed into a unified subjective experience of perceptual fluency.

Aeroacoustic Characterization of the NASA Ames Experimental Aero-Physics Branch 32- by 48-Inch Subsonic Wind Tunnel with a 24-Element Phased Microphone Array

NASA Technical Reports Server (NTRS)

Costanza, Bryan T.; Horne, William C.; Schery, S. D.; Babb, Alex T.

2011-01-01

The Aero-Physics Branch at NASA Ames Research Center utilizes a 32- by 48-inch subsonic wind tunnel for aerodynamics research. The feasibility of acquiring acoustic measurements with a phased microphone array was recently explored. Acoustic characterization of the wind tunnel was carried out with a floor-mounted 24-element array and two ceiling-mounted speakers. The minimum speaker level for accurate level measurement was evaluated for various tunnel speeds up to a Mach number of 0.15 and streamwise speaker locations. A variety of post-processing procedures, including conventional beamforming and deconvolutional processing such as TIDY, were used. The speaker measurements, with and without flow, were used to compare actual versus simulated in-flow speaker calibrations. Data for wind-off speaker sound and wind-on tunnel background noise were found valuable for predicting sound levels for which the speakers were detectable when the wind was on. Speaker sources were detectable 2 - 10 dB below the peak background noise level with conventional data processing. The effectiveness of background noise cross-spectral matrix subtraction was assessed and found to improve the detectability of test sound sources by approximately 10 dB over a wide frequency range.

Circadian Clock Synchronization of the Cell Cycle in Zebrafish Occurs through a Gating Mechanism Rather Than a Period-phase Locking Process.

PubMed

Laranjeiro, Ricardo; Tamai, T Katherine; Letton, William; Hamilton, Noémie; Whitmore, David

2018-04-01

Studies from a number of model systems have shown that the circadian clock controls expression of key cell cycle checkpoints, thus providing permissive or inhibitory windows in which specific cell cycle events can occur. However, a major question remains: Is the clock actually regulating the cell cycle through such a gating mechanism or, alternatively, is there a coupling process that controls the speed of cell cycle progression? Using our light-responsive zebrafish cell lines, we address this issue directly by synchronizing the cell cycle in culture simply by changing the entraining light-dark (LD) cycle in the incubator without the need for pharmacological intervention. Our results show that the cell cycle rapidly reentrains to a shifted LD cycle within 36 h, with changes in p21 expression and subsequent S phase timing occurring within the first few hours of resetting. Reentrainment of mitosis appears to lag S phase resetting by 1 circadian cycle. The range of entrainment of the zebrafish clock to differing LD cycles is large, from 16 to 32 hour periods. We exploited this feature to explore cell cycle entrainment at both the population and single cell levels. At the population level, cell cycle length is shortened or lengthened under corresponding T-cycles, suggesting that a 1:1 coupling mechanism is capable of either speeding up or slowing down the cell cycle. However, analysis at the single cell level reveals that this, in fact, is not true and that a gating mechanism is the fundamental method of timed cell cycle regulation in zebrafish. Cell cycle length at the single cell level is virtually unaltered with varying T-cycles.

Circadian Clock Synchronization of the Cell Cycle in Zebrafish Occurs through a Gating Mechanism Rather Than a Period-phase Locking Process

PubMed Central

Tamai, T. Katherine; Letton, William; Hamilton, Noémie; Whitmore, David

2018-01-01

Studies from a number of model systems have shown that the circadian clock controls expression of key cell cycle checkpoints, thus providing permissive or inhibitory windows in which specific cell cycle events can occur. However, a major question remains: Is the clock actually regulating the cell cycle through such a gating mechanism or, alternatively, is there a coupling process that controls the speed of cell cycle progression? Using our light-responsive zebrafish cell lines, we address this issue directly by synchronizing the cell cycle in culture simply by changing the entraining light-dark (LD) cycle in the incubator without the need for pharmacological intervention. Our results show that the cell cycle rapidly reentrains to a shifted LD cycle within 36 h, with changes in p21 expression and subsequent S phase timing occurring within the first few hours of resetting. Reentrainment of mitosis appears to lag S phase resetting by 1 circadian cycle. The range of entrainment of the zebrafish clock to differing LD cycles is large, from 16 to 32 hour periods. We exploited this feature to explore cell cycle entrainment at both the population and single cell levels. At the population level, cell cycle length is shortened or lengthened under corresponding T-cycles, suggesting that a 1:1 coupling mechanism is capable of either speeding up or slowing down the cell cycle. However, analysis at the single cell level reveals that this, in fact, is not true and that a gating mechanism is the fundamental method of timed cell cycle regulation in zebrafish. Cell cycle length at the single cell level is virtually unaltered with varying T-cycles. PMID:29444612

3D printing of microtube in solid phantom to simulate tissue oxygenation and perfusion (Conference Presentation)

NASA Astrophysics Data System (ADS)

Lv, Xiang; Xue, Yue; Wang, Haili; Shen, Shu Wei; Zhou, Ximing; Liu, Guangli; Dong, Erbao; Xu, Ronald X.

2017-03-01

Tissue-simulating phantoms with interior vascular network may facilitate traceable calibration and quantitative validation of many medical optical devices. However, a solid phantom that reliably simulates tissue oxygenation and blood perfusion is still not available. This paper presents a new method to fabricate hollow microtubes for blood vessel simulation in solid phantoms. The fabrication process combines ultraviolet (UV) rapid prototyping technique with fluid mechanics of a coaxial jet flow. Polydimethylsiloxane (PDMS) and a UV-curable polymer are mixed at the designated ratio and extruded through a coaxial needle device to produce a coaxial jet flow. The extruded jet flow is quickly photo-polymerized by ultraviolet (UV) light to form vessel-simulating solid structures at different sizes ranging from 700 μm to 1000 μm. Microtube structures with adequate mechanical properties can be fabricated by adjusting material compositions and illumination intensity. Curved, straight and stretched microtubes can be formed by adjusting the extrusion speed of the materials and the speed of the 3D printing platform. To simulate vascular structures in biologic tissue, we embed vessel-simulating microtubes in a gel wax phantom of 10 cm x10 cm x 5 cm at the depth from 1 to 2 mm. Bloods at different oxygenation and hemoglobin concentration levels are circulated through the microtubes at different flow rates in order to simulate different oxygenation and perfusion conditions. The simulated physiologic parameters are detected by a tissue oximeter and a laser speckle blood flow meter respectively and compared with the actual values. Our experiments demonstrate that the proposed 3D printing process is able to produce solid phantoms with simulated vascular networks for potential applications in medical device calibration and drug delivery studies.

Multi-resolution simulation of focused ultrasound propagation through ovine skull from a single-element transducer

NASA Astrophysics Data System (ADS)

Yoon, Kyungho; Lee, Wonhye; Croce, Phillip; Cammalleri, Amanda; Yoo, Seung-Schik

2018-05-01

Transcranial focused ultrasound (tFUS) is emerging as a non-invasive brain stimulation modality. Complicated interactions between acoustic pressure waves and osseous tissue introduce many challenges in the accurate targeting of an acoustic focus through the cranium. Image-guidance accompanied by a numerical simulation is desired to predict the intracranial acoustic propagation through the skull; however, such simulations typically demand heavy computation, which warrants an expedited processing method to provide on-site feedback for the user in guiding the acoustic focus to a particular brain region. In this paper, we present a multi-resolution simulation method based on the finite-difference time-domain formulation to model the transcranial propagation of acoustic waves from a single-element transducer (250 kHz). The multi-resolution approach improved computational efficiency by providing the flexibility in adjusting the spatial resolution. The simulation was also accelerated by utilizing parallelized computation through the graphic processing unit. To evaluate the accuracy of the method, we measured the actual acoustic fields through ex vivo sheep skulls with different sonication incident angles. The measured acoustic fields were compared to the simulation results in terms of focal location, dimensions, and pressure levels. The computational efficiency of the presented method was also assessed by comparing simulation speeds at various combinations of resolution grid settings. The multi-resolution grids consisting of 0.5 and 1.0 mm resolutions gave acceptable accuracy (under 3 mm in terms of focal position and dimension, less than 5% difference in peak pressure ratio) with a speed compatible with semi real-time user feedback (within 30 s). The proposed multi-resolution approach may serve as a novel tool for simulation-based guidance for tFUS applications.

Multi-resolution simulation of focused ultrasound propagation through ovine skull from a single-element transducer.

PubMed

Yoon, Kyungho; Lee, Wonhye; Croce, Phillip; Cammalleri, Amanda; Yoo, Seung-Schik

2018-05-10

Transcranial focused ultrasound (tFUS) is emerging as a non-invasive brain stimulation modality. Complicated interactions between acoustic pressure waves and osseous tissue introduce many challenges in the accurate targeting of an acoustic focus through the cranium. Image-guidance accompanied by a numerical simulation is desired to predict the intracranial acoustic propagation through the skull; however, such simulations typically demand heavy computation, which warrants an expedited processing method to provide on-site feedback for the user in guiding the acoustic focus to a particular brain region. In this paper, we present a multi-resolution simulation method based on the finite-difference time-domain formulation to model the transcranial propagation of acoustic waves from a single-element transducer (250 kHz). The multi-resolution approach improved computational efficiency by providing the flexibility in adjusting the spatial resolution. The simulation was also accelerated by utilizing parallelized computation through the graphic processing unit. To evaluate the accuracy of the method, we measured the actual acoustic fields through ex vivo sheep skulls with different sonication incident angles. The measured acoustic fields were compared to the simulation results in terms of focal location, dimensions, and pressure levels. The computational efficiency of the presented method was also assessed by comparing simulation speeds at various combinations of resolution grid settings. The multi-resolution grids consisting of 0.5 and 1.0 mm resolutions gave acceptable accuracy (under 3 mm in terms of focal position and dimension, less than 5% difference in peak pressure ratio) with a speed compatible with semi real-time user feedback (within 30 s). The proposed multi-resolution approach may serve as a novel tool for simulation-based guidance for tFUS applications.

Laterality effects in motor learning by mental practice in right-handers.

PubMed

Gentili, R J; Papaxanthis, C

2015-06-25

Converging evidences suggest that mental movement simulation and actual movement production share similar neurocognitive and learning processes. Although a large body of data is available in the literature regarding mental states involving the dominant arm, examinations for the nondominant arm are sparse. Does mental training, through motor-imagery practice, with the dominant arm or the nondominant arm is equally efficient for motor learning? In the current study, we investigated laterality effects in motor learning by motor-imagery practice. Four groups of right-hander adults mentally and physically performed as fast and accurately as possible (speed/accuracy trade-off paradigm) successive reaching movements with their dominant or nondominant arm (physical-training-dominant-arm, mental-training-dominant-arm, physical-training-nondominant-arm, and mental-training-nondominant-arm groups). Movement time was recorded and analyzed before, during, and after the training sessions. We found that physical and mental practice had a positive effect on the motor performance (i.e., decrease in movement time) of both arms through similar learning process (i.e., similar exponential learning curves). However, movement time reduction in the posttest session was significantly higher after physical practice than motor-imagery practice for both arms. More importantly, motor-imagery practice with the dominant arm resulted in larger and more robust improvements in movement speed compared to motor-imagery practice with the nondominant arm. No such improvements were observed in the control group. Our results suggest a superiority of the dominant arm in motor learning by mental practice. We discussed these findings from the perspective of the internal models theory. Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

Rotor Re-Design for the SSME Fuel Flowmeter

NASA Technical Reports Server (NTRS)

Marcu, Bogdan

1999-01-01

The present report describes the process of redesigning a new rotor for the SSME Fuel Flowmeter. The new design addresses the specific requirement of a lower rotor speed which would allow the SSME operation at 1 15% rated power level without reaching a blade excitation by the wakes behind the hexagonal flow straightener upstream at frequencies close to the blade natural frequency. A series of calculations combining fleet flowmeters test data, airfoil fluid dynamics and CFD simulations of flow patterns behind the flowmeter's hexagonal straightener has led to a blade twist design alpha = alpha (radius) targeting a kf constant of 0.8256. The kf constant relates the fuel volume flow to the flowmeter rotor speed, for this particular value 17685 GPM at 3650 RPM. Based on this angle distribution, two actual blade designs were developed. A first design using the same blade airfoil as the original design targeted the new kf value only. A second design using a variable blade chord length and airfoil relative thickness targeted simultaneously the new kf value and an optimum blade design destined to provide smooth and stable operation and a significant increase in the blade natural frequency associated with the first bending mode, such that a comfortable margin could be obtained at 115% RPL. The second design is a result of a concurrent engineering process, during which several iterations were made in order to achieve a targeted blade natural frequency associated with the first bending mode of 1300 Hz. Water flow tests preliminary results indicate a kf value of 0.8179 for the f-irst design, which is within 1% of the target value. The second design rotor shows a natural frequency associated with the first bending mode of 1308 Hz, and a water-flow calibration constant of kf 0.8169.

Digital intermediate frequency QAM modulator using parallel processing

DOEpatents

Pao, Hsueh-Yuan [Livermore, CA; Tran, Binh-Nien [San Ramon, CA

2008-05-27

The digital Intermediate Frequency (IF) modulator applies to various modulation types and offers a simple and low cost method to implement a high-speed digital IF modulator using field programmable gate arrays (FPGAs). The architecture eliminates multipliers and sequential processing by storing the pre-computed modulated cosine and sine carriers in ROM look-up-tables (LUTs). The high-speed input data stream is parallel processed using the corresponding LUTs, which reduces the main processing speed, allowing the use of low cost FPGAs.

Architecture Of High Speed Image Processing System

NASA Astrophysics Data System (ADS)

Konishi, Toshio; Hayashi, Hiroshi; Ohki, Tohru

1988-01-01

One of architectures for a high speed image processing system which corresponds to a new algorithm for a shape understanding is proposed. And the hardware system which is based on the archtecture was developed. Consideration points of the architecture are mainly that using processors should match with the processing sequence of the target image and that the developed system should be used practically in an industry. As the result, it was possible to perform each processing at a speed of 80 nano-seconds a pixel.

Cognitive ability at age 11 and 70 years, information processing speed, and APOE variation: the Lothian Birth Cohort 1936 study.

PubMed

Luciano, Michelle; Gow, Alan J; Harris, Sarah E; Hayward, Caroline; Allerhand, Mike; Starr, John M; Visscher, Peter M; Deary, Ian J

2009-03-01

The e4 allele of the apolipoprotein E (APOE) gene confers risk of Alzheimer's disease and, in some studies, relates to cognitive ability and decline in older people without Alzheimer's disease. Its relationship with processing speed, a contributor to cognitive decline with age, is largely unknown. This study tests the association of APOE with cognition and speed, with and without covarying childhood mental ability. The 1,013 participants were tested on cognitive ability at age 11 as part of the Scottish Mental Survey of 1947 and, at age 70, were tested on reasoning, working memory, information processing speed, and executive function. The results showed that APOE was associated with the general cognitive factor, 2 nonverbal tests, and choice reaction time (RT) variability; as expected, the e4 allele was the risk allele. RT measures and a general speed factor were nonlinearly related to APOE when factoring childhood ability (p < .05): The correlation between childhood ability and speed was lower in e4 allele carriers. APOE has an influence on nonverbal cognition in old age and interacts with childhood IQ to influence processing speed.

Measuring automatic retrieval: a comparison of implicit memory, process dissociation, and speeded response procedures.

PubMed

Horton, Keith D; Wilson, Daryl E; Vonk, Jennifer; Kirby, Sarah L; Nielsen, Tina

2005-07-01

Using the stem completion task, we compared estimates of automatic retrieval from an implicit memory task, the process dissociation procedure, and the speeded response procedure. Two standard manipulations were employed. In Experiment 1, a depth of processing effect was found on automatic retrieval using the speeded response procedure although this effect was substantially reduced in Experiment 2 when lexical processing was required of all words. In Experiment 3, the speeded response procedure showed an advantage of full versus divided attention at study on automatic retrieval. An implicit condition showed parallel effects in each study, suggesting that implicit stem completion may normally provide a good estimate of automatic retrieval. Also, we replicated earlier findings from the process dissociation procedure, but estimates of automatic retrieval from this procedure were consistently lower than those from the speeded response procedure, except when conscious retrieval was relatively low. We discuss several factors that may contribute to the conflicting outcomes, including the evidence for theoretical assumptions and criterial task differences between implicit and explicit tests.

Chaotic home environment is associated with reduced infant processing speed under high task demands.

PubMed

Tomalski, Przemysław; Marczuk, Karolina; Pisula, Ewa; Malinowska, Anna; Kawa, Rafał; Niedźwiecka, Alicja

2017-08-01

Early adversity has profound long-term consequences for child development across domains. The effects of early adversity on structural and functional brain development were shown for infants under 12 months of life. However, the causal mechanisms of these effects remain relatively unexplored. Using a visual habituation task we investigated whether chaotic home environment may affect processing speed in 5.5 month-old infants (n=71). We found detrimental effects of chaos on processing speed for complex but not for simple visual stimuli. No effects of socio-economic status on infant processing speed were found although the sample was predominantly middle class. Our results indicate that chaotic early environment may adversely affect processing speed in early infancy, but only when greater cognitive resources need to be deployed. The study highlights an attractive avenue for research on the mechanisms linking home environment with the development of attention control. Copyright © 2017 Elsevier Inc. All rights reserved.

Topography of Slow Sigma Power during Sleep is Associated with Processing Speed in Preschool Children.

PubMed

Doucette, Margaret R; Kurth, Salome; Chevalier, Nicolas; Munakata, Yuko; LeBourgeois, Monique K

2015-11-04

Cognitive development is influenced by maturational changes in processing speed, a construct reflecting the rapidity of executing cognitive operations. Although cognitive ability and processing speed are linked to spindles and sigma power in the sleep electroencephalogram (EEG), little is known about such associations in early childhood, a time of major neuronal refinement. We calculated EEG power for slow (10-13 Hz) and fast (13.25-17 Hz) sigma power from all-night high-density electroencephalography (EEG) in a cross-sectional sample of healthy preschool children (n = 10, 4.3 ± 1.0 years). Processing speed was assessed as simple reaction time. On average, reaction time was 1409 ± 251 ms; slow sigma power was 4.0 ± 1.5 μV²; and fast sigma power was 0.9 ± 0.2 μV². Both slow and fast sigma power predominated over central areas. Only slow sigma power was correlated with processing speed in a large parietal electrode cluster (p < 0.05, r ranging from -0.6 to -0.8), such that greater power predicted faster reaction time. Our findings indicate regional correlates between sigma power and processing speed that are specific to early childhood and provide novel insights into the neurobiological features of the EEG that may underlie developing cognitive abilities.

Episodic feeling-of-knowing accuracy and cued recall in the elderly: evidence for double dissociation involving executive functioning and processing speed.

PubMed

Perrotin, Audrey; Isingrini, Michel; Souchay, Céline; Clarys, David; Taconnat, Laurence

2006-05-01

This research investigated adult age differences in a metamemory monitoring task-episodic feeling-of-knowing (FOK) and in an episodic memory task-cued recall. Executive functioning and processing speed were examined as mediators of these age differences. Young and elderly adults were administered an episodic FOK task, a cued recall task, executive tests and speed tests. Age-related decline was observed on all the measures. Correlation analyses revealed a pattern of double dissociation which indicates a specific relationship between executive score and FOK accuracy, and between speed score and cued recall. When executive functioning and processing speed were evaluated concurrently on FOK and cued recall variables, hierarchical regression analyses showed that executive score was a better mediator of age-related variance in FOK, and that speed score was the better mediator of age-related variance in cued recall.

Processing speed and visuospatial executive function predict visual working memory ability in older adults.

PubMed

Brown, Louise A; Brockmole, James R; Gow, Alan J; Deary, Ian J

2012-01-01

BACKGROUND/STUDY CONTEXT: Visual working memory (VWM) has been shown to be particularly age sensitive. Determining which measures share variance with this cognitive ability in older adults may help to elucidate the key factors underlying the effects of aging. Predictors of VWM (measured by a modified Visual Patterns Test) were investigated in a subsample (N = 44, mean age = 73) of older adults from the Lothian Birth Cohort 1936 (LBC1936; Deary et al., 2007 , BMC Geriatrics, 7, 28). Childhood intelligence (Moray House Test) and contemporaneous measures of processing speed (four-choice reaction time), executive function (verbal fluency; block design), and spatial working memory (backward spatial span), were assessed as potential predictors. All contemporaneous measures except verbal fluency were significantly associated with VWM, and processing speed had the largest effect size (r = -.53, p < .001). In linear regression analysis, even after adjusting for childhood intelligence, processing speed and the executive measure associated with visuospatial organization accounted for 35% of the variance in VWM. Processing speed may affect VWM performance in older adults via speed of encoding and/or rate of rehearsal, while executive resources specifically associated with visuospatial material are also important.

Conveying Looming with a Localized Tactile Cue

DTIC Science & Technology

2015-04-01

leaning and reflexive head righting required at different speeds of linear or angular motion, the angle of contact of the foot to the substrate (e.g...approach information (e.g., relative distance updates) prior to actual contact , as has been reported for visual and auditory displays. A few studies have...Jacobs, 2013). Cancar et al. asked 12 subjects to estimate time-to- contact of a radially-expanding tactile or visual flow field representing a

Plasma and radiation detection via fiber interferometry

NASA Astrophysics Data System (ADS)

Dolan, D. H.; Bell, K.; Fox, B.; Jones, S. C.; Knapp, P.; Gomez, M. R.; Martin, M.; Porwitzky, A.; Laity, G.

2018-01-01

Photonic Doppler velocimetry tracks motion during high-speed, single-event experiments using telecommunication fiber components. The same technology can be applied in situations where there is no actual motion, but rather a change in the optical path length. Migration of plasma into vacuum alters the refractive index near a fiber probe, while intense radiation modifies the refractive index of the fiber itself. These changes can diagnose extreme environments in a flexible, time-resolved manner.

Plasma and radiation detection via fiber interferometry

DOE PAGES

Dolan, D. H.; Bell, Kate Suzanne; Fox, Brian Philip; ...

2018-01-17

Photonic Doppler velocimetry tracks motion during high-speed, single-event experiments using telecommunication fiber components. The same technology can be applied in situations where there is no actual motion, but rather a change in the optical path length. Migration of plasma into vacuum alters the refractive index near a fiber probe, while intense radiation modifies the refractive index of the fiber itself. Lastly, these changes can diagnose extreme environments in a flexible, time-resolved manner.

Dispersion Characteristics of a Beam-Driven Cylindrical Waveguide with Dielectric Liner.

DTIC Science & Technology

1982-04-01

applications of near-millimeter waves. The experiment initiated at HDL represents one approach to designing such a radiation source. The foundation for this...experiment has been laid by Felch et al at Dartmouth College.1 𔃼 Very simply, that experiment consists of passing an intense, relativistic electron beam...accelerated to relativistic speeds through the dielectric-lined resonator, where the actual produc- tion of radiation takes place. As a result of the

Multiscale Space-Time Computational Methods for Fluid-Structure Interactions

DTIC Science & Technology

2015-09-13

prescribed fully or partially, is from an actual locust, extracted from high-speed, multi-camera video recordings of the locust in a wind tunnel . We use...With creative methods for coupling the fluid and structure, we can increase the scope and efficiency of the FSI modeling . Multiscale methods, which now...play an important role in computational mathematics, can also increase the accuracy and efficiency of the computer modeling techniques. The main

Plasma and radiation detection via fiber interferometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dolan, D. H.; Bell, Kate Suzanne; Fox, Brian Philip

Photonic Doppler velocimetry tracks motion during high-speed, single-event experiments using telecommunication fiber components. The same technology can be applied in situations where there is no actual motion, but rather a change in the optical path length. Migration of plasma into vacuum alters the refractive index near a fiber probe, while intense radiation modifies the refractive index of the fiber itself. Lastly, these changes can diagnose extreme environments in a flexible, time-resolved manner.

An examination of mediators of the transfer of cognitive speed of processing training to everyday functional performance.

PubMed

Edwards, Jerri D; Ruva, Christine L; O'Brien, Jennifer L; Haley, Christine B; Lister, Jennifer J

2013-06-01

The purpose of these analyses was to examine mediators of the transfer of cognitive speed of processing training to improved everyday functional performance (J. D. Edwards, V. G. Wadley,, D. E. Vance, D. L. Roenker, & K. K. Ball, 2005, The impact of speed of processing training on cognitive and everyday performance. Aging & Mental Health, 9, 262-271). Cognitive speed of processing and visual attention (as measured by the Useful Field of View Test; UFOV) were examined as mediators of training transfer. Secondary data analyses were conducted from the Staying Keen in Later Life (SKILL) study, a randomized cohort study including 126 community dwelling adults 63 to 87 years of age. In the SKILL study, participants were randomized to an active control group or cognitive speed of processing training (SOPT), a nonverbal, computerized intervention involving perceptual practice of visual tasks. Prior analyses found significant effects of training as measured by the UFOV and Timed Instrumental Activities of Daily Living (TIADL) Tests. Results from the present analyses indicate that speed of processing for a divided attention task significantly mediated the effect of SOPT on everyday performance (e.g., TIADL) in a multiple mediation model accounting for 91% of the variance. These findings suggest that everyday functional improvements found from SOPT are directly attributable to improved UFOV performance, speed of processing for divided attention in particular. Targeting divided attention in cognitive interventions may be important to positively affect everyday functioning among older adults. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Self-Perceived and Actual Motor Competence in Young British Children.

PubMed

Duncan, Michael J; Jones, Victoria; O'Brien, Wesley; Barnett, Lisa M; Eyre, Emma L J

2018-04-01

Children's perception of their own motor competence is an important correlate of their actual motor competence. The current study is the first to examine this association in British children and the first to use both product and process measures of actual motor competence. A total of 258 children (139 boys and 119 girls; aged 4 to 7 years, Mean = 5.6, SD = .96) completed measures of self-perceived motor competence using the Pictorial Scale for Perceived Movement Competence in Young Children. Children were classified as "Low," "Medium," or "High" perceived competence based on tertile analysis. Actual motor competence was assessed with the Test of Gross Motor Development-2 (a process measure) and a composite of 10-m sprint run time, standing long jump distance, and 1-kg seated medicine ball throw (collectively, a product measure). Data for process and product measures were analyzed using a 2 (sex) × 3 (high, medium, low perceived competence) analysis of covariance, with body mass index, calculated from height and mass, and age controlled. Boys obtained significantly higher scores than girls for both the process ( p = .044) and product ( p = .001) measures of actual motor competence. Boys had significantly ( p = .04) higher scores for perceived competence compared to girls. Compared to children classified as medium and high self-perceived competence, children classified as low self-perceived competence had lower process ( p = .001) and product scores (i.e., medium, p = .009 and high, p = .0001) of actual motor competence. Age ( p = .0001) and body mass index ( p = .0001) were significantly associated with product motor competence. Strategies to enhance actual motor competence may benefit children's self-perceived motor competence.

The effect of phasic auditory alerting on visual perception.

PubMed

Petersen, Anders; Petersen, Annemarie Hilkjær; Bundesen, Claus; Vangkilde, Signe; Habekost, Thomas

2017-08-01

Phasic alertness refers to a short-lived change in the preparatory state of the cognitive system following an alerting signal. In the present study, we examined the effect of phasic auditory alerting on distinct perceptual processes, unconfounded by motor components. We combined an alerting/no-alerting design with a pure accuracy-based single-letter recognition task. Computational modeling based on Bundesen's Theory of Visual Attention was used to examine the effect of phasic alertness on visual processing speed and threshold of conscious perception. Results show that phasic auditory alertness affects visual perception by increasing the visual processing speed and lowering the threshold of conscious perception (Experiment 1). By manipulating the intensity of the alerting cue, we further observed a positive relationship between alerting intensity and processing speed, which was not seen for the threshold of conscious perception (Experiment 2). This was replicated in a third experiment, in which pupil size was measured as a physiological marker of alertness. Results revealed that the increase in processing speed was accompanied by an increase in pupil size, substantiating the link between alertness and processing speed (Experiment 3). The implications of these results are discussed in relation to a newly developed mathematical model of the relationship between levels of alertness and the speed with which humans process visual information. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of helicopter transmission seals, task 2

NASA Technical Reports Server (NTRS)

Hayden, T. S.; Keller, C. H., Jr.

1973-01-01

High speed helicopter transmission seal concepts were designed, fabricated and tested. The concepts were a dual element split ring seal and a circumferential seal. The tests were performed in a rig using an actual input quill assembly. The test conditions were selected to simulate transmission operation and were 230 F oil temperature, and a sliding speed of 9400 ft/min. The split ring seal exhibited gross leakage and was considered unsatisfactory, while the circumferential seal leakage was less than 1 c.c./hour; this leakage is within acceptable limits. The circumferential seal wear was only to .0005 inches during a 100 hour run (40 starts and stops). During a 40 hour contamination test (mesh silica flour) the seal total wear was a maximum of .004 inches. This wear is considered acceptable.

Research on the key technology of update of land survey spatial data based on embedded GIS and GPS

NASA Astrophysics Data System (ADS)

Chen, Dan; Liu, Yanfang; Yu, Hai; Xia, Yin

2009-10-01

According to the actual needs of the second land-use survey and the PDA's characteristics of small volume and small memory, it can be analyzed that the key technology of the data collection system of field survey based on GPS-PDA is the read speed of the data. In order to enhance the speed and efficiency of the analysis of the spatial data on mobile devices, we classify the layers of spatial data; get the Layer-Grid Index by getting the different levels and blocks of the layer of spatial data; then get the R-TREE index of the spatial data objects. Different scale levels of space are used in different levels management. The grid method is used to do the block management.

Improvement of Functional Properties by Sever Plastic Deformation on Parts of Titanium Biomaterials

NASA Astrophysics Data System (ADS)

Czán, Andrej; Babík, Ondrej; Daniš, Igor; Martikáň, Pavol; Czánová, Tatiana

2017-12-01

Main task of materials for invasive implantology is their biocompatibility with the tissue but also requirements for improving the functional properties of given materials are increasing constantly. One of problems of materials biocompatibility is the impossibility to improve of functional properties by change the percentage of the chemical elements and so it is necessary to find other innovative methods of improving of functional properties such as mechanical action in the form of high deformation process. This paper is focused on various methods of high deformation process such as Equal Channel Angular Pressing (ECAP) when rods with record strength properties were obtained.The actual studies of the deformation process properties as tri-axial compress stress acting on workpiece with high speed of deformation shows effects similar to results obtained using the other methods, but in lower levels of stress. Hydrostatic extrusion (HE) is applying for the purpose of refining the structure of the commercially pure titanium up to nano-scale. Experiments showed the ability to reduce the grain size below 100 nm. Due to the significant change in the performance of the titanium materials by severe plastic deformation is required to identify the processability of materials with respect to the identification of created surfaces and monitoring the surface integrity, where the experimental results show ability of SPD technologies application on biomaterials.

Adaptive platform for fluorescence microscopy-based high-content screening

NASA Astrophysics Data System (ADS)

Geisbauer, Matthias; Röder, Thorsten; Chen, Yang; Knoll, Alois; Uhl, Rainer

2010-04-01

Fluorescence microscopy has become a widely used tool for the study of medically relevant intra- and intercellular processes. Extracting meaningful information out of a bulk of acquired images is usually performed during a separate post-processing task. Thus capturing raw data results in an unnecessary huge number of images, whereas usually only a few images really show the particular information that is searched for. Here we propose a novel automated high-content microscope system, which enables experiments to be carried out with only a minimum of human interaction. It facilitates a huge speed-increase for cell biology research and its applications compared to the widely performed workflows. Our fluorescence microscopy system can automatically execute application-dependent data processing algorithms during the actual experiment. They are used for image contrast enhancement, cell segmentation and/or cell property evaluation. On-the-fly retrieved information is used to reduce data and concomitantly control the experiment process in real-time. Resulting in a closed loop of perception and action the system can greatly decrease the amount of stored data on one hand and increases the relative valuable data content on the other hand. We demonstrate our approach by addressing the problem of automatically finding cells with a particular combination of labeled receptors and then selectively stimulate them with antagonists or agonists. The results are then compared against the results of traditional, static systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newman, Jennifer; Clifton, Andrew; Bonin, Timothy

As wind turbine sizes increase and wind energy expands to more complex and remote sites, remote-sensing devices such as lidars are expected to play a key role in wind resource assessment and power performance testing. The switch to remote-sensing devices represents a paradigm shift in the way the wind industry typically obtains and interprets measurement data for wind energy. For example, the measurement techniques and sources of uncertainty for a remote-sensing device are vastly different from those associated with a cup anemometer on a meteorological tower. Current IEC standards for quantifying remote sensing device uncertainty for power performance testing considermore » uncertainty due to mounting, calibration, and classification of the remote sensing device, among other parameters. Values of the uncertainty are typically given as a function of the mean wind speed measured by a reference device and are generally fixed, leading to climatic uncertainty values that apply to the entire measurement campaign. However, real-world experience and a consideration of the fundamentals of the measurement process have shown that lidar performance is highly dependent on atmospheric conditions, such as wind shear, turbulence, and aerosol content. At present, these conditions are not directly incorporated into the estimated uncertainty of a lidar device. In this presentation, we describe the development of a new dynamic lidar uncertainty framework that adapts to current flow conditions and more accurately represents the actual uncertainty inherent in lidar measurements under different conditions. In this new framework, sources of uncertainty are identified for estimation of the line-of-sight wind speed and reconstruction of the three-dimensional wind field. These sources are then related to physical processes caused by the atmosphere and lidar operating conditions. The framework is applied to lidar data from a field measurement site to assess the ability of the framework to predict errors in lidar-measured wind speed. The results show how uncertainty varies over time and can be used to help select data with different levels of uncertainty for different applications, for example, low uncertainty data for power performance testing versus all data for plant performance monitoring.« less

Behavior of fragmentation front in a porous viscoelastic material

NASA Astrophysics Data System (ADS)

Ichihara, M.; Takayama, K.

2002-12-01

We are developing laboratory experiments to investigate dynamics of magma fragmentation during explosive volcanic eruptions. Fragmentation of such a mixture as magma consisting of viscoelastic melt, bubbles and solid particles, is not known yet, and experiments are necessary to establish a mathematical model. It has been shown that viscoelastic silicone compound (Dow Corning 3179) is a useful analogous material to simulate magma fragmentation. In the previous work, a porous specimen made of the compound was rapidly decompressed and development of brittle fragmentation was observed. However, there were arguments that the experiment was different from actual processes which produce fragments as small as volcanic ash, because in the experiment the specimen was broken into only several pieces. This time, results of the improved experiments are presented. The experimental apparatus is a kind of a vertical shock tube, which mainly consists of a high pressure test section and low pressure chambers. The test section is made of acrylic tube of which inner diameter is 25 mm. The internal phenomenon is recorded by a high-speed video camera. Pressure is measured in the gas above and beneath the specimen by piezoelectric transducers. The specimen is prepared in the following way. First, an acrylic tube filled with the compound is put in a nitrogen tank and kept at 45 bar for more than 8 hours. The compound absorbs the gas and equilibrates with the nitrogen. Next, the tank is decompressed back to the atmospheric pressure slowly. Nitrogen exsolves and bubbles are formed in the compound quite uniformly. Finally, the expanded compound sticking out of both ends of the tube is cut down, and the tube containing the specimen is attached to the shock tube. The specimen is rapidly decompressed by 24, 16, and 8 bars. The high-speed video images demonstrate a sequence of the fragmentation process. We observe propagation of a clear fracture front at 50 m/s for 24 bar of decompression and at smaller speed for smaller decompression. The pressure change associated with development of the fragmentation is analyzed and effects of over pressure in the pores and permeable gas flow on fragmentation behavior are discussed.

Cognitive Risk Factors for Specific Learning Disorder: Processing Speed, Temporal Processing, and Working Memory.

PubMed

Moll, Kristina; Göbel, Silke M; Gooch, Debbie; Landerl, Karin; Snowling, Margaret J

2016-01-01

High comorbidity rates between reading disorder (RD) and mathematics disorder (MD) indicate that, although the cognitive core deficits underlying these disorders are distinct, additional domain-general risk factors might be shared between the disorders. Three domain-general cognitive abilities were investigated in children with RD and MD: processing speed, temporal processing, and working memory. Since attention problems frequently co-occur with learning disorders, the study examined whether these three factors, which are known to be associated with attention problems, account for the comorbidity between these disorders. The sample comprised 99 primary school children in four groups: children with RD, children with MD, children with both disorders (RD+MD), and typically developing children (TD controls). Measures of processing speed, temporal processing, and memory were analyzed in a series of ANCOVAs including attention ratings as covariate. All three risk factors were associated with poor attention. After controlling for attention, associations with RD and MD differed: Although deficits in verbal memory were associated with both RD and MD, reduced processing speed was related to RD, but not MD; and the association with RD was restricted to processing speed for familiar nameable symbols. In contrast, impairments in temporal processing and visuospatial memory were associated with MD, but not RD. © Hammill Institute on Disabilities 2014.

Hypothesis regarding the transformation of the intended direction of movement during the production of graphic trajectories: a study of drawing movements in 8- to 12-year-old children.

PubMed

Pellizzer, Giuseppe; Zesiger, Pascal

2009-03-01

Children from 8 to 12 years of age drew figure-eights and ellipses at a self-chosen tempo on a digitizing tablet. Global aspects (perimeter and average speed) and local aspects (relation between instantaneous speed and curvature) of performance were analyzed across age groups and types of figures. We tested the predictions of the transformation model, which is based on the hypothesis that changing the intended direction of movement is a time-consuming process that affects the evolution in time of the movement trajectory, and compared how well it fitted the data relative to the power law. We found that the relation between speed and curvature was typically better described by the transformation model than by the power law. However, the power law provided a better description when ellipses were drawn at a fast speed. The analyses of the parameters of the transformation model indicate that processing speed increased linearly with age. In addition, the results suggest that the effects of the spring-like properties of the arm were noticeable when ellipses were drawn at a fast speed. This study indicates that both biomechanical properties and central processes have an effect on the kinematics of continuous movements and particularly on the relation between speed and curvature. However, their relative importance varies with the type of figure and average movement speed. In conclusion, the results support the hypothesis that a time-consuming process of transformation of the intended direction of movement is operating during the production of continuous movements and that this process increases in speed between 8 to 12 years of age.

Biomechanical simulation of vocal fold dynamics in adults based on laryngeal high-speed videoendoscopy

PubMed Central

Gómez, Pablo; Patel, Rita R.; Alexiou, Christoph; Bohr, Christopher; Schützenberger, Anne

2017-01-01

Motivation Human voice is generated in the larynx by the two oscillating vocal folds. Owing to the limited space and accessibility of the larynx, endoscopic investigation of the actual phonatory process in detail is challenging. Hence the biomechanics of the human phonatory process are still not yet fully understood. Therefore, we adapt a mathematical model of the vocal folds towards vocal fold oscillations to quantify gender and age related differences expressed by computed biomechanical model parameters. Methods The vocal fold dynamics are visualized by laryngeal high-speed videoendoscopy (4000 fps). A total of 33 healthy young subjects (16 females, 17 males) and 11 elderly subjects (5 females, 6 males) were recorded. A numerical two-mass model is adapted to the recorded vocal fold oscillations by varying model masses, stiffness and subglottal pressure. For adapting the model towards the recorded vocal fold dynamics, three different optimization algorithms (Nelder–Mead, Particle Swarm Optimization and Simulated Bee Colony) in combination with three cost functions were considered for applicability. Gender differences and age-related kinematic differences reflected by the model parameters were analyzed. Results and conclusion The biomechanical model in combination with numerical optimization techniques allowed phonatory behavior to be simulated and laryngeal parameters involved to be quantified. All three optimization algorithms showed promising results. However, only one cost function seems to be suitable for this optimization task. The gained model parameters reflect the phonatory biomechanics for men and women well and show quantitative age- and gender-specific differences. The model parameters for younger females and males showed lower subglottal pressures, lower stiffness and higher masses than the corresponding elderly groups. Females exhibited higher subglottal pressures, smaller oscillation masses and larger stiffness than the corresponding similar aged male groups. Optimizing numerical models towards vocal fold oscillations is useful to identify underlying laryngeal components controlling the phonatory process. PMID:29121085

Dynamics of carbon dioxide emission at Mammoth Mountain, California

USGS Publications Warehouse

Rogie, J.D.; Kerrick, Derrill M.; Sorey, M.L.; Chiodini, G.; Galloway, D.L.

2001-01-01

Mammoth Mountain, a dormant volcano in the eastern Sierra Nevada, California, has been passively degassing large quantities of cold magmatic CO2 since 1990 following a 6-month-long earthquake swarm associated with a shallow magmatic intrussion in 1989. A search for any link between gas discharge and volcanic hazard at this popular recreation area led us to initiate a detailed study of the degassing process in 1997. Our continuous monitoring results elucidate some of the physical controls that influence dynamics in flank CO2 degassing at this volcano. High coherence between variations in CO2 efflux and variations in atmospheric pressure and wind speed imply that meteorological parameters account for much, if not all of the variability in CO2 efflux rates. Our results help explain differences among previously published estimates of CO2 efflux at Mammoth Mountain and indicate that the long-term (annual) CO2 degassing rate has in fact remained constant since ~ 1997. Discounting the possibility of large meteorologically driven temporal variations in gas efflux at other volcanoes may result in spurious interpretations of transients do not reflect actual geologic processes. ?? 2001 Elsevier Science B.V. All rights reserved.