A performance analysis of advanced I/O architectures for PC-based network file servers

NASA Astrophysics Data System (ADS)

Huynh, K. D.; Khoshgoftaar, T. M.

1994-12-01

In the personal computing and workstation environments, more and more I/O adapters are becoming complete functional subsystems that are intelligent enough to handle I/O operations on their own without much intervention from the host processor. The IBM Subsystem Control Block (SCB) architecture has been defined to enhance the potential of these intelligent adapters by defining services and conventions that deliver command information and data to and from the adapters. In recent years, a new storage architecture, the Redundant Array of Independent Disks (RAID), has been quickly gaining acceptance in the world of computing. In this paper, we would like to discuss critical system design issues that are important to the performance of a network file server. We then present a performance analysis of the SCB architecture and disk array technology in typical network file server environments based on personal computers (PCs). One of the key issues investigated in this paper is whether a disk array can outperform a group of disks (of same type, same data capacity, and same cost) operating independently, not in parallel as in a disk array.

OPAL: An Open-Source MPI-IO Library over Cray XT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Weikuan; Vetter, Jeffrey S; Canon, Richard Shane

Parallel IO over Cray XT is supported by a vendor-supplied MPI-IO package. This package contains a proprietary ADIO implementation built on top of the sysio library. While it is reasonable to maintain a stable code base for application scientists' convenience, it is also very important to the system developers and researchers to analyze and assess the effectiveness of parallel IO software, and accordingly, tune and optimize the MPI-IO implementation. A proprietary parallel IO code base relinquishes such flexibilities. On the other hand, a generic UFS-based MPI-IO implementation is typically used on many Linux-based platforms. We have developed an open-source MPI-IOmore » package over Lustre, referred to as OPAL (OPportunistic and Adaptive MPI-IO Library over Lustre). OPAL provides a single source-code base for MPI-IO over Lustre on Cray XT and Linux platforms. Compared to Cray implementation, OPAL provides a number of good features, including arbitrary specification of striping patterns and Lustre-stripe aligned file domain partitioning. This paper presents the performance comparisons between OPAL and Cray's proprietary implementation. Our evaluation demonstrates that OPAL achieves the performance comparable to the Cray implementation. We also exemplify the benefits of an open source package in revealing the underpinning of the parallel IO performance.« less

Eye on Io.

ERIC Educational Resources Information Center

Lewis, Scott M.

1985-01-01

"Io," one of four satellites of Jupiter, orbits its mother planet in roughly the same plane as Earth orbits the sun. Guidelines for collecting data about Io using a reflecting telescope, 35mm camera, and adapter are presented. A computer program used in studying Io's maximum distance from Jupiter is available. (DH)

A Malicious Pattern Detection Engine for Embedded Security Systems in the Internet of Things

PubMed Central

Oh, Doohwan; Kim, Deokho; Ro, Won Woo

2014-01-01

With the emergence of the Internet of Things (IoT), a large number of physical objects in daily life have been aggressively connected to the Internet. As the number of objects connected to networks increases, the security systems face a critical challenge due to the global connectivity and accessibility of the IoT. However, it is difficult to adapt traditional security systems to the objects in the IoT, because of their limited computing power and memory size. In light of this, we present a lightweight security system that uses a novel malicious pattern-matching engine. We limit the memory usage of the proposed system in order to make it work on resource-constrained devices. To mitigate performance degradation due to limitations of computation power and memory, we propose two novel techniques, auxiliary shifting and early decision. Through both techniques, we can efficiently reduce the number of matching operations on resource-constrained systems. Experiments and performance analyses show that our proposed system achieves a maximum speedup of 2.14 with an IoT object and provides scalable performance for a large number of patterns. PMID:25521382

Extreme Worlds of the Outer Solar System: Dynamic Processes on Uranus & Io

NASA Astrophysics Data System (ADS)

Kleer, Katherine Rebecca de

A central goal of planetary science is the creation of a framework within which the properties of each solar system body can be understood as the product of initial conditions acted on by fundamental physical processes. The solar system's extreme worlds -- those objects that lie at the far ends of the spectrum in terms of planetary environment -- bring to light our misconceptions and present us with opportunities to expand and generalize this framework. Unraveling the processes at work in diverse planetary environments contextualizes our understanding of Earth, and provides a basis for interpreting specific signatures from planets beyond our own solar system. Uranus and Io, with their unusual planetary environments, present two examples of such worlds in the outer solar system. Uranus, one of the outer solar system's ice giants, produces an anomalously low heat flow and orbits the sun on its side. Its relative lack of bright storm features and its bizarre multi-decadal seasons provide insight into the relative effects of internal heat flow and time- varying solar insolation on atmospheric dynamics, while its narrow rings composed of dark, macroscopic particles encode the history of bombardment and satellite disruption within the system. Jupiter's moon Io hosts the most extreme volcanic activity anywhere in the solar system. Its tidally-powered geological activity provides a window into this satellite's interior, permitting rare and valuable investigations into the exchange of heat and materials between interiors and surfaces. In particular, Io provides a laboratory for studying the process of tidal heating, which shapes planets and satellites in our solar system and beyond. A comparison between Earth and Io contextualizes the volcanism at work on our home planet, revealing the effects of planetary size, atmospheric density, and plate tectonics on the style and mechanisms of geological activity. This dissertation investigates the processes at work on these solar system outliers through studies of Uranus' atmosphere and rings and of Io's thermal activity. I show that Uranus' rings are spectrally flat in the near-infrared, setting them apart from all other ring systems in the solar system. I investigate the vertical profile of species in Uranus' atmosphere, and demonstrate evidence for seasonal trends in the upper atmosphere on decadal timescales. Based on a large high-cadence dataset of Io's volcanism obtained with adaptive optics over 100 nights, I show that the thermal timelines of Io's volcanoes indicate at least two distinct classes of eruption. The asymmetric spatial distribution of Io's volcanic heat flow suggests additional mechanisms at work modulating the effects of tidal heating. I present the detection of one of the most powerful eruptions ever seen on Io, which I use to derive a eruption temperature of >1300 K, consistent with a highly mafic magma composition. Geophysical modeling of the thermal timeline of Loki Patera, a distinctive volcanic feature on Io, indicates low lava thermal conductivities also consistent with a highly-mafic silicate composition. Ultra-high-resolution thermal mapping of this patera reveals a multi-phase volcanic resurfacing process that hints at the plumbing system underlying this massive volcanic feature. The results presented here are founded on near-infrared observations of unprecedented resolution in the spatial, spectral, and temporal domains. The interpretation of the data utilizes rigorous statistical techniques to draw meaningful conclusions. In addition to the scientific impact of the findings, this work therefore also pioneers specific ground-based telescope capabilities and analysis tools, and demonstrates their utility to solar system science. Chapter 2 presents the first high-resolution spectra of Uranus' rings. Chapter 3 introduces Markov Chain Monte Carlo simulations into ice giant atmospheric radiative transfer model- ing, permitting a rigorous analysis of parameter uncertainties and correlations. Chapters 4-7 present results from the first multi-year, high-cadence ground-based observing campaign to study Io's volcanism with sufficient spatial resolution to directly resolve individual volcanoes. The thermal timelines of these volcanoes provide unprecedented insight into the variability and distribution of Io's volcanism over a wide range of timescales. Chapter 7 uses geometric arguments to deduce topography of a volcanic feature on Io based on observations at a range of viewing angles. Finally, Chapter 8 presents the first ground-based observations to map a thermal feature on Io at a spatial resolution of ˜10 km on Io's surface, derived from the first mutual satellite occultation event to be observed with adaptive optics on a dual-telescope interferometric system. These techniques can all be expanded and applied to these and other targets in future near-infrared studies.

Adaptive voting computer system

NASA Technical Reports Server (NTRS)

Koczela, L. J.; Wilgus, D. S. (Inventor)

1974-01-01

A computer system is reported that uses adaptive voting to tolerate failures and operates in a fail-operational, fail-safe manner. Each of four computers is individually connected to one of four external input/output (I/O) busses which interface with external subsystems. Each computer is connected to receive input data and commands from the other three computers and to furnish output data commands to the other three computers. An adaptive control apparatus including a voter-comparator-switch (VCS) is provided for each computer to receive signals from each of the computers and permits adaptive voting among the computers to permit the fail-operational, fail-safe operation.

Dual RBFNNs-Based Model-Free Adaptive Control With Aspen HYSYS Simulation.

PubMed

Zhu, Yuanming; Hou, Zhongsheng; Qian, Feng; Du, Wenli

2017-03-01

In this brief, we propose a new data-driven model-free adaptive control (MFAC) method with dual radial basis function neural networks (RBFNNs) for a class of discrete-time nonlinear systems. The main novelty lies in that it provides a systematic design method for controller structure by the direct usage of I/O data, rather than using the first-principle model or offline identified plant model. The controller structure is determined by equivalent-dynamic-linearization representation of the ideal nonlinear controller, and the controller parameters are tuned by the pseudogradient information extracted from the I/O data of the plant, which can deal with the unknown nonlinear system. The stability of the closed-loop control system and the stability of the training process for RBFNNs are guaranteed by rigorous theoretical analysis. Meanwhile, the effectiveness and the applicability of the proposed method are further demonstrated by the numerical example and Aspen HYSYS simulation of distillation column in crude styrene produce process.

Simple and cost-effective hardware and software for functional brain mapping using intrinsic optical signal imaging.

PubMed

Harrison, Thomas C; Sigler, Albrecht; Murphy, Timothy H

2009-09-15

We describe a simple and low-cost system for intrinsic optical signal (IOS) imaging using stable LED light sources, basic microscopes, and commonly available CCD cameras. IOS imaging measures activity-dependent changes in the light reflectance of brain tissue, and can be performed with a minimum of specialized equipment. Our system uses LED ring lights that can be mounted on standard microscope objectives or video lenses to provide a homogeneous and stable light source, with less than 0.003% fluctuation across images averaged from 40 trials. We describe the equipment and surgical techniques necessary for both acute and chronic mouse preparations, and provide software that can create maps of sensory representations from images captured by inexpensive 8-bit cameras or by 12-bit cameras. The IOS imaging system can be adapted to commercial upright microscopes or custom macroscopes, eliminating the need for dedicated equipment or complex optical paths. This method can be combined with parallel high resolution imaging techniques such as two-photon microscopy.

10 Gigabit Ethernet Performance on SGI Altix and Origin Systems

NASA Technical Reports Server (NTRS)

Meyer, Andy

2005-01-01

As the state of high performance computing continues to advance, the size of datasets continue to grow, driving a need for high bandwidth data networks. family of networks. 10 Gigabit Ethernet is the latest step in the popular Ethernet We have evaluated the S2io Xframe 10 Gigabit Ethernet adapter on 512p SGI Altix systems running ProPack 3, and Origin systems running Irix 6.5.24 and 6.5.26 in our production supercomputing environment. We encountered a number of performance and stability issues, which were promptly dealt with by SGI and S2io. Using nttcp we tested TCP performance for single and multiple streams, and we tested file transfer using NFS and bbftp. We will present the results of our testing, including the effects of various tuning options on throughput and CPU utilization, and offer suggestions for configuring and tuning S2io 10 Gigabit Ethernet cards in an Altix/Linux or Origin/Irix environment.

Differentially Private Distributed Sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fink, Glenn A.

The growth of the Internet of Things (IoT) creates the possibility of decentralized systems of sensing and actuation, potentially on a global scale. IoT devices connected to cloud networks can offer Sensing and Actuation as a Service (SAaaS) enabling networks of sensors to grow to a global scale. But extremely large sensor networks can violate privacy, especially in the case where IoT devices are mobile and connected directly to the behaviors of people. The thesis of this paper is that by adapting differential privacy (adding statistically appropriate noise to query results) to groups of geographically distributed sensors privacy could bemore » maintained without ever sending all values up to a central curator and without compromising the overall accuracy of the data collected. This paper outlines such a scheme and performs an analysis of differential privacy techniques adapted to edge computing in a simulated sensor network where ground truth is known. The positive and negative outcomes of employing differential privacy in distributed networks of devices are discussed and a brief research agenda is presented.« less

A Hybrid Data Compression Scheme for Power Reduction in Wireless Sensors for IoT.

PubMed

Deepu, Chacko John; Heng, Chun-Huat; Lian, Yong

2017-04-01

This paper presents a novel data compression and transmission scheme for power reduction in Internet-of-Things (IoT) enabled wireless sensors. In the proposed scheme, data is compressed with both lossy and lossless techniques, so as to enable hybrid transmission mode, support adaptive data rate selection and save power in wireless transmission. Applying the method to electrocardiogram (ECG), the data is first compressed using a lossy compression technique with a high compression ratio (CR). The residual error between the original data and the decompressed lossy data is preserved using entropy coding, enabling a lossless restoration of the original data when required. Average CR of 2.1 × and 7.8 × were achieved for lossless and lossy compression respectively with MIT/BIH database. The power reduction is demonstrated using a Bluetooth transceiver and is found to be reduced to 18% for lossy and 53% for lossless transmission respectively. Options for hybrid transmission mode, adaptive rate selection and system level power reduction make the proposed scheme attractive for IoT wireless sensors in healthcare applications.

Multi-petascale highly efficient parallel supercomputer

DOEpatents

Asaad, Sameh; Bellofatto, Ralph E.; Blocksome, Michael A.; Blumrich, Matthias A.; Boyle, Peter; Brunheroto, Jose R.; Chen, Dong; Cher, Chen -Yong; Chiu, George L.; Christ, Norman; Coteus, Paul W.; Davis, Kristan D.; Dozsa, Gabor J.; Eichenberger, Alexandre E.; Eisley, Noel A.; Ellavsky, Matthew R.; Evans, Kahn C.; Fleischer, Bruce M.; Fox, Thomas W.; Gara, Alan; Giampapa, Mark E.; Gooding, Thomas M.; Gschwind, Michael K.; Gunnels, John A.; Hall, Shawn A.; Haring, Rudolf A.; Heidelberger, Philip; Inglett, Todd A.; Knudson, Brant L.; Kopcsay, Gerard V.; Kumar, Sameer; Mamidala, Amith R.; Marcella, James A.; Megerian, Mark G.; Miller, Douglas R.; Miller, Samuel J.; Muff, Adam J.; Mundy, Michael B.; O'Brien, John K.; O'Brien, Kathryn M.; Ohmacht, Martin; Parker, Jeffrey J.; Poole, Ruth J.; Ratterman, Joseph D.; Salapura, Valentina; Satterfield, David L.; Senger, Robert M.; Smith, Brian; Steinmacher-Burow, Burkhard; Stockdell, William M.; Stunkel, Craig B.; Sugavanam, Krishnan; Sugawara, Yutaka; Takken, Todd E.; Trager, Barry M.; Van Oosten, James L.; Wait, Charles D.; Walkup, Robert E.; Watson, Alfred T.; Wisniewski, Robert W.; Wu, Peng

2015-07-14

A Multi-Petascale Highly Efficient Parallel Supercomputer of 100 petaOPS-scale computing, at decreased cost, power and footprint, and that allows for a maximum packaging density of processing nodes from an interconnect point of view. The Supercomputer exploits technological advances in VLSI that enables a computing model where many processors can be integrated into a single Application Specific Integrated Circuit (ASIC). Each ASIC computing node comprises a system-on-chip ASIC utilizing four or more processors integrated into one die, with each having full access to all system resources and enabling adaptive partitioning of the processors to functions such as compute or messaging I/O on an application by application basis, and preferably, enable adaptive partitioning of functions in accordance with various algorithmic phases within an application, or if I/O or other processors are underutilized, then can participate in computation or communication nodes are interconnected by a five dimensional torus network with DMA that optimally maximize the throughput of packet communications between nodes and minimize latency.

Agile and Adaptive IT Ecosystem, Results, Outlook, and Recommendations

DTIC Science & Technology

2014-06-01

http://netbeans.dzone.com/news/war-fighter- netbeans -platform 5 http://www.afei.org/events/4A07/Documents/1-DI2E%20Brochure%20ISA_10APR13.pdf 6...Client ( NetBeans ), and OSGI bundles (Karafe). DoD systems also use both the Android and iOS mobile operating systems. Each technology has a specific

From WSN towards WoT: Open API Scheme Based on oneM2M Platforms.

PubMed

Kim, Jaeho; Choi, Sung-Chan; Ahn, Il-Yeup; Sung, Nak-Myoung; Yun, Jaeseok

2016-10-06

Conventional computing systems have been able to be integrated into daily objects and connected to each other due to advances in computing and network technologies, such as wireless sensor networks (WSNs), forming a global network infrastructure, called the Internet of Things (IoT). To support the interconnection and interoperability between heterogeneous IoT systems, the availability of standardized, open application programming interfaces (APIs) is one of the key features of common software platforms for IoT devices, gateways, and servers. In this paper, we present a standardized way of extending previously-existing WSNs towards IoT systems, building the world of the Web of Things (WoT). Based on the oneM2M software platforms developed in the previous project, we introduce a well-designed open API scheme and device-specific thing adaptation software (TAS) enabling WSN elements, such as a wireless sensor node, to be accessed in a standardized way on a global scale. Three pilot services are implemented (i.e., a WiFi-enabled smart flowerpot, voice-based control for ZigBee-connected home appliances, and WiFi-connected AR.Drone control) to demonstrate the practical usability of the open API scheme and TAS modules. Full details on the method of integrating WSN elements into three example systems are described at the programming code level, which is expected to help future researchers in integrating their WSN systems in IoT platforms, such as oneM2M. We hope that the flexibly-deployable, easily-reusable common open API scheme and TAS-based integration method working with the oneM2M platforms will help the conventional WSNs in diverse industries evolve into the emerging WoT solutions.

From WSN towards WoT: Open API Scheme Based on oneM2M Platforms

PubMed Central

Kim, Jaeho; Choi, Sung-Chan; Ahn, Il-Yeup; Sung, Nak-Myoung; Yun, Jaeseok

2016-01-01

Conventional computing systems have been able to be integrated into daily objects and connected to each other due to advances in computing and network technologies, such as wireless sensor networks (WSNs), forming a global network infrastructure, called the Internet of Things (IoT). To support the interconnection and interoperability between heterogeneous IoT systems, the availability of standardized, open application programming interfaces (APIs) is one of the key features of common software platforms for IoT devices, gateways, and servers. In this paper, we present a standardized way of extending previously-existing WSNs towards IoT systems, building the world of the Web of Things (WoT). Based on the oneM2M software platforms developed in the previous project, we introduce a well-designed open API scheme and device-specific thing adaptation software (TAS) enabling WSN elements, such as a wireless sensor node, to be accessed in a standardized way on a global scale. Three pilot services are implemented (i.e., a WiFi-enabled smart flowerpot, voice-based control for ZigBee-connected home appliances, and WiFi-connected AR.Drone control) to demonstrate the practical usability of the open API scheme and TAS modules. Full details on the method of integrating WSN elements into three example systems are described at the programming code level, which is expected to help future researchers in integrating their WSN systems in IoT platforms, such as oneM2M. We hope that the flexibly-deployable, easily-reusable common open API scheme and TAS-based integration method working with the oneM2M platforms will help the conventional WSNs in diverse industries evolve into the emerging WoT solutions. PMID:27782058

Functional Optical Coherence Tomography Enables In Vivo Physiological Assessment of Retinal Rod and Cone Photoreceptors

PubMed Central

Zhang, Qiuxiang; Lu, Rongwen; Wang, Benquan; Messinger, Jeffrey D.; Curcio, Christine A.; Yao, Xincheng

2015-01-01

Transient intrinsic optical signal (IOS) changes have been observed in retinal photoreceptors, suggesting a unique biomarker for eye disease detection. However, clinical deployment of IOS imaging is challenging due to unclear IOS sources and limited signal-to-noise ratios (SNRs). Here, by developing high spatiotemporal resolution optical coherence tomography (OCT) and applying an adaptive algorithm for IOS processing, we were able to record robust IOSs from single-pass measurements. Transient IOSs, which might reflect an early stage of light phototransduction, are consistently observed in the photoreceptor outer segment almost immediately (<4 ms) after retinal stimulation. Comparative studies of dark- and light-adapted retinas have demonstrated the feasibility of functional OCT mapping of rod and cone photoreceptors, promising a new method for early disease detection and improved treatment of diseases such as age-related macular degeneration (AMD) and other eye diseases that can cause photoreceptor damage. PMID:25901915

Functional Optical Coherence Tomography Enables In Vivo Physiological Assessment of Retinal Rod and Cone Photoreceptors

NASA Astrophysics Data System (ADS)

Zhang, Qiuxiang; Lu, Rongwen; Wang, Benquan; Messinger, Jeffrey D.; Curcio, Christine A.; Yao, Xincheng

2015-04-01

Transient intrinsic optical signal (IOS) changes have been observed in retinal photoreceptors, suggesting a unique biomarker for eye disease detection. However, clinical deployment of IOS imaging is challenging due to unclear IOS sources and limited signal-to-noise ratios (SNRs). Here, by developing high spatiotemporal resolution optical coherence tomography (OCT) and applying an adaptive algorithm for IOS processing, we were able to record robust IOSs from single-pass measurements. Transient IOSs, which might reflect an early stage of light phototransduction, are consistently observed in the photoreceptor outer segment almost immediately (<4 ms) after retinal stimulation. Comparative studies of dark- and light-adapted retinas have demonstrated the feasibility of functional OCT mapping of rod and cone photoreceptors, promising a new method for early disease detection and improved treatment of diseases such as age-related macular degeneration (AMD) and other eye diseases that can cause photoreceptor damage.

A Four-Phase Modulation System for Use with an Adaptive Array.

DTIC Science & Technology

1982-07-01

MODULATION SYSTEM FORIteia epr * ~USE WITH AN ADAPTIVE ARRAY *P RIGOG EOTM~E _____________________________________ ESL 711679-5 7s AUTHOeO~) 9 . CONTRACT r0...OUSOLE1T6 UNCLASSIFIED SECURITY CLASSIFICATION OF THIS P040E (when Doe I91 r2 UNCLASSIFIED 8ncumV CL"M,ICAnIo, o TP , ImS 8... ., 9 fte-H - LMS...nterval has a duration of : Tb seconds. a(t) is a pseudonotse code, i.e., a maximum length " lInear shift register sequence [ 9 ]. The code symbol interval

Adaptive MCS selection and resource planning for energy-efficient communication in LTE-M based IoT sensing platform.

PubMed

Dao, Nhu-Ngoc; Park, Minho; Kim, Joongheon; Cho, Sungrae

2017-01-01

As an important part of IoTization trends, wireless sensing technologies have been involved in many fields of human life. In cellular network evolution, the long term evolution advanced (LTE-A) networks including machine-type communication (MTC) features (named LTE-M) provide a promising infrastructure for a proliferation of Internet of things (IoT) sensing platform. However, LTE-M may not be optimally exploited for directly supporting such low-data-rate devices in terms of energy efficiency since it depends on core technologies of LTE that are originally designed for high-data-rate services. Focusing on this circumstance, we propose a novel adaptive modulation and coding selection (AMCS) algorithm to address the energy consumption problem in the LTE-M based IoT-sensing platform. The proposed algorithm determines the optimal pair of MCS and the number of primary resource blocks (#PRBs), at which the transport block size is sufficient to packetize the sensing data within the minimum transmit power. In addition, a quantity-oriented resource planning (QORP) technique that utilizes these optimal MCS levels as main criteria for spectrum allocation has been proposed for better adapting to the sensing node requirements. The simulation results reveal that the proposed approach significantly reduces the energy consumption of IoT sensing nodes and #PRBs up to 23.09% and 25.98%, respectively.

Adaptive MCS selection and resource planning for energy-efficient communication in LTE-M based IoT sensing platform

PubMed Central

Dao, Nhu-Ngoc; Park, Minho; Kim, Joongheon

2017-01-01

As an important part of IoTization trends, wireless sensing technologies have been involved in many fields of human life. In cellular network evolution, the long term evolution advanced (LTE-A) networks including machine-type communication (MTC) features (named LTE-M) provide a promising infrastructure for a proliferation of Internet of things (IoT) sensing platform. However, LTE-M may not be optimally exploited for directly supporting such low-data-rate devices in terms of energy efficiency since it depends on core technologies of LTE that are originally designed for high-data-rate services. Focusing on this circumstance, we propose a novel adaptive modulation and coding selection (AMCS) algorithm to address the energy consumption problem in the LTE-M based IoT-sensing platform. The proposed algorithm determines the optimal pair of MCS and the number of primary resource blocks (#PRBs), at which the transport block size is sufficient to packetize the sensing data within the minimum transmit power. In addition, a quantity-oriented resource planning (QORP) technique that utilizes these optimal MCS levels as main criteria for spectrum allocation has been proposed for better adapting to the sensing node requirements. The simulation results reveal that the proposed approach significantly reduces the energy consumption of IoT sensing nodes and #PRBs up to 23.09% and 25.98%, respectively. PMID:28796804

Extreme I/O on HPC for HEP using the Burst Buffer at NERSC

NASA Astrophysics Data System (ADS)

Bhimji, Wahid; Bard, Debbie; Burleigh, Kaylan; Daley, Chris; Farrell, Steve; Fasel, Markus; Friesen, Brian; Gerhardt, Lisa; Liu, Jialin; Nugent, Peter; Paul, Dave; Porter, Jeff; Tsulaia, Vakho

2017-10-01

In recent years there has been increasing use of HPC facilities for HEP experiments. This has initially focussed on less I/O intensive workloads such as generator-level or detector simulation. We now demonstrate the efficient running of I/O-heavy analysis workloads on HPC facilities at NERSC, for the ATLAS and ALICE LHC collaborations as well as astronomical image analysis for DESI and BOSS. To do this we exploit a new 900 TB NVRAM-based storage system recently installed at NERSC, termed a Burst Buffer. This is a novel approach to HPC storage that builds on-demand filesystems on all-SSD hardware that is placed on the high-speed network of the new Cori supercomputer. We describe the hardware and software involved in this system, and give an overview of its capabilities, before focusing in detail on how the ATLAS, ALICE and astronomical workflows were adapted to work on this system. We describe these modifications and the resulting performance results, including comparisons to other filesystems. We demonstrate that we can meet the challenging I/O requirements of HEP experiments and scale to many thousands of cores accessing a single shared storage system.

Vibration Pattern Imager (VPI): A control and data acquisition system for scanning laser vibrometers

NASA Technical Reports Server (NTRS)

Rizzi, Stephen A.; Brown, Donald E.; Shaffer, Thomas A.

1993-01-01

The Vibration Pattern Imager (VPI) system was designed to control and acquire data from scanning laser vibrometer sensors. The PC computer based system uses a digital signal processing (DSP) board and an analog I/O board to control the sensor and to process the data. The VPI system was originally developed for use with the Ometron VPI Sensor, but can be readily adapted to any commercially available sensor which provides an analog output signal and requires analog inputs for control of mirror positioning. The sensor itself is not part of the VPI system. A graphical interface program, which runs on a PC under the MS-DOS operating system, functions in an interactive mode and communicates with the DSP and I/O boards in a user-friendly fashion through the aid of pop-up menus. Two types of data may be acquired with the VPI system: single point or 'full field.' In the single point mode, time series data is sampled by the A/D converter on the I/O board (at a user-defined sampling rate for a selectable number of samples) and is stored by the PC. The position of the measuring point (adjusted by mirrors in the sensor) is controlled via a mouse input. The mouse input is translated to output voltages by the D/A converter on the I/O board to control the mirror servos. In the 'full field' mode, the measurement point is moved over a user-selectable rectangular area. The time series data is sampled by the A/D converter on the I/O board (at a user-defined sampling rate for a selectable number of samples) and converted to a root-mean-square (rms) value by the DSP board. The rms 'full field' velocity distribution is then uploaded for display and storage on the PC.

Detection of no-model input-output pairs in closed-loop systems.

PubMed

Potts, Alain Segundo; Alvarado, Christiam Segundo Morales; Garcia, Claudio

2017-11-01

The detection of no-model input-output (IO) pairs is important because it can speed up the multivariable system identification process, since all the pairs with null transfer functions are previously discarded and it can also improve the identified model quality, thus improving the performance of model based controllers. In the available literature, the methods focus just on the open-loop case, since in this case there is not the effect of the controller forcing the main diagonal in the transfer matrix to one and all the other terms to zero. In this paper, a modification of a previous method able to detect no-model IO pairs in open-loop systems is presented, but adapted to perform this duty in closed-loop systems. Tests are performed by using the traditional methods and the proposed one to show its effectiveness. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Io's Plasma Environment During the Galileo Flyby: Global Three-Dimensional MHD Modeling with Adaptive Mesh Refinement

NASA Technical Reports Server (NTRS)

Combi, M. R.; Kabin, K.; Gombosi, T. I.; DeZeeuw, D. L.; Powell, K. G.

1998-01-01

The first results for applying a three-dimensional multimedia ideal MHD model for the mass-loaded flow of Jupiter's corotating magnetospheric plasma past Io are presented. The model is able to consider simultaneously physically realistic conditions for ion mass loading, ion-neutral drag, and intrinsic magnetic field in a full global calculation without imposing artificial dissipation. Io is modeled with an extended neutral atmosphere which loads the corotating plasma torus flow with mass, momentum, and energy. The governing equations are solved using adaptive mesh refinement on an unstructured Cartesian grid using an upwind scheme for AHMED. For the work described in this paper we explored a range of models without an intrinsic magnetic field for Io. We compare our results with particle and field measurements made during the December 7, 1995, flyby of to, as published by the Galileo Orbiter experiment teams. For two extreme cases of lower boundary conditions at Io, our model can quantitatively explain the variation of density along the spacecraft trajectory and can reproduce the general appearance of the variations of magnetic field and ion pressure and temperature. The net fresh ion mass-loading rates are in the range of approximately 300-650 kg/s, and equivalent charge exchange mass-loading rates are in the range approximately 540-1150 kg/s in the vicinity of Io.

BPcontrol

PubMed Central

Carrera, Adrián; Pifarré, Marc; Vilaplana, Jordi; Cuadrado, Josep; Solsona, Sara; Mateo, Jordi

2016-01-01

Summary Background Hypertension or high blood pressure is on the rise. Not only does it affect the elderly but is also increasingly spreading to younger sectors of the population. Treating this condition involves exhaustive monitoring of patients. The current mobile health services can be improved to perform this task more effectively. Objective To develop a useful, user-friendly, robust and efficient app, to monitor hypertensive patients and adapted to the particular requirements of hypertension. Methods This work presents BPcontrol, an Android and iOS app that allows hypertensive patients to communicate with their health-care centers, thus facilitating monitoring and diagnosis. Usability, robustness and efficiency factors for BPcontrol were evaluated for different devices and operating systems (Android, iOS and system-aware). Furthermore, its features were compared with other similar apps in the literature. Results BPcontrol is robust and user-friendly. The respective start-up efficiency of the Android and iOS versions of BPcontrol were 2.4 and 8.8 times faster than a system-aware app. Similar values were obtained for the communication efficiency (7.25 and 11.75 times faster for the Android and iOS respectively). When comparing plotting performance, BPcontrol was on average 2.25 times faster in the Android case. Most of the apps in the literature have no communication with a server, thus making it impossible to compare their performance with BPcontrol. Conclusions Its optimal design and the good behavior of its facilities make BPcontrol a very promising mobile app for monitoring hypertensive patients. PMID:27924346

BPcontrol. A Mobile App to Monitor Hypertensive Patients.

PubMed

Carrera, Adrian; Pifarré, Marc; Vilaplana, Jordi; Cuadrado, Josep; Solsona, Sara; Mateo, Jordi; Solsona, Francesc

2016-12-07

Hypertension or high blood pressure is on the rise. Not only does it affect the elderly but is also increasingly spreading to younger sectors of the population. Treating this condition involves exhaustive monitoring of patients. The current mobile health services can be improved to perform this task more effectively. To develop a useful, user-friendly, robust and efficient app, to monitor hypertensive patients and adapted to the particular requirements of hypertension. This work presents BPcontrol, an Android and iOS app that allows hypertensive patients to communicate with their health-care centers, thus facilitating monitoring and diagnosis. Usability, robustness and efficiency factors for BPcontrol were evaluated for different devices and operating systems (Android, iOS and system-aware). Furthermore, its features were compared with other similar apps in the literature. BPcontrol is robust and user-friendly. The respective start-up efficiency of the Android and iOS versions of BPcontrol were 2.4 and 8.8 times faster than a system-aware app. Similar values were obtained for the communication efficiency (7.25 and 11.75 times faster for the Android and iOS respectively). When comparing plotting performance, BPcontrol was on average 2.25 times faster in the Android case. Most of the apps in the literature have no communication with a server, thus making it impossible to compare their performance with BPcontrol. Its optimal design and the good behavior of its facilities make BPcontrol a very promising mobile app for monitoring hypertensive patients.

Modeling the effect of propofol and remifentanil combinations for sedation-analgesia in endoscopic procedures using an Adaptive Neuro Fuzzy Inference System (ANFIS).

PubMed

Gambús, P L; Jensen, E W; Jospin, M; Borrat, X; Martínez Pallí, G; Fernández-Candil, J; Valencia, J F; Barba, X; Caminal, P; Trocóniz, I F

2011-02-01

The increasing demand for anesthetic procedures in the gastrointestinal endoscopy area has not been followed by a similar increase in the methods to provide and control sedation and analgesia for these patients. In this study, we evaluated different combinations of propofol and remifentanil, administered through a target-controlled infusion system, to estimate the optimal concentrations as well as the best way to control the sedative effects induced by the combinations of drugs in patients undergoing ultrasonographic endoscopy. One hundred twenty patients undergoing ultrasonographic endoscopy were randomized to receive, by means of a target-controlled infusion system, a fixed effect-site concentration of either propofol or remifentanil of 8 different possible concentrations, allowing adjustment of the concentrations of the other drug. Predicted effect-site propofol (C(e)pro) and remifentanil (C(e)remi) concentrations, parameters derived from auditory evoked potential, autoregressive auditory evoked potential index (AAI/2) and electroencephalogram (bispectral index [BIS] and index of consciousness [IoC]) signals, as well as categorical scores of sedation (Ramsay Sedation Scale [RSS] score) in the presence or absence of nociceptive stimulation, were collected, recorded, and analyzed using an Adaptive Neuro Fuzzy Inference System. The models described for the relationship between C(e)pro and C(e)remi versus AAI/2, BIS, and IoC were diagnosed for inaccuracy using median absolute performance error (MDAPE) and median root mean squared error (MDRMSE), and for bias using median performance error (MDPE). The models were validated in a prospective group of 68 new patients receiving different combinations of propofol and remifentanil. The predictive ability (P(k)) of AAI/2, BIS, and IoC with respect to the sedation level, RSS score, was also explored. Data from 110 patients were analyzed in the training group. The resulting estimated models had an MDAPE of 32.87, 12.89, and 8.77; an MDRMSE of 17.01, 12.81, and 9.40; and an MDPE of -1.86, 3.97, and 2.21 for AAI/2, BIS, and IoC, respectively, in the absence of stimulation and similar values under stimulation. P(k) values were 0.82, 0.81, and 0.85 for AAI/2, BIS, and IoC, respectively. The model predicted the prospective validation data with an MDAPE of 34.81, 14.78, and 10.25; an MDRMSE of 16.81, 15.91, and 11.81; an MDPE of -8.37, 5.65, and -1.43; and P(k) values of 0.81, 0.8, and 0.8 for AAI/2, BIS, and IoC, respectively. A model relating C(e)pro and C(e)remi to AAI/2, BIS, and IoC has been developed and prospectively validated. Based on these models, the (C(e)pro, C(e)remi) concentration pairs that provide an RSS score of 4 range from (1.8 μg·mL(-1), 1.5 ng·mL(-1)) to (2.7 μg·mL(-1), 0 ng·mL(-1)). These concentrations are associated with AAI/2 values of 25 to 30, BIS of 71 to 75, and IoC of 72 to 76. The presence of noxious stimulation increases the requirements of C(e)pro and C(e)remi to achieve the same degree of sedative effects.

Data management for the internet of things: design primitives and solution.

PubMed

Abu-Elkheir, Mervat; Hayajneh, Mohammad; Ali, Najah Abu

2013-11-14

The Internet of Things (IoT) is a networking paradigm where interconnected, smart objects continuously generate data and transmit it over the Internet. Much of the IoT initiatives are geared towards manufacturing low-cost and energy-efficient hardware for these objects, as well as the communication technologies that provide objects interconnectivity. However, the solutions to manage and utilize the massive volume of data produced by these objects are yet to mature. Traditional database management solutions fall short in satisfying the sophisticated application needs of an IoT network that has a truly global-scale. Current solutions for IoT data management address partial aspects of the IoT environment with special focus on sensor networks. In this paper, we survey the data management solutions that are proposed for IoT or subsystems of the IoT. We highlight the distinctive design primitives that we believe should be addressed in an IoT data management solution, and discuss how they are approached by the proposed solutions. We finally propose a data management framework for IoT that takes into consideration the discussed design elements and acts as a seed to a comprehensive IoT data management solution. The framework we propose adapts a federated, data- and sources-centric approach to link the diverse Things with their abundance of data to the potential applications and services that are envisioned for IoT.

Data Management for the Internet of Things: Design Primitives and Solution

PubMed Central

Abu-Elkheir, Mervat; Hayajneh, Mohammad; Ali, Najah Abu

2013-01-01

The Internet of Things (IoT) is a networking paradigm where interconnected, smart objects continuously generate data and transmit it over the Internet. Much of the IoT initiatives are geared towards manufacturing low-cost and energy-efficient hardware for these objects, as well as the communication technologies that provide objects interconnectivity. However, the solutions to manage and utilize the massive volume of data produced by these objects are yet to mature. Traditional database management solutions fall short in satisfying the sophisticated application needs of an IoT network that has a truly global-scale. Current solutions for IoT data management address partial aspects of the IoT environment with special focus on sensor networks. In this paper, we survey the data management solutions that are proposed for IoT or subsystems of the IoT. We highlight the distinctive design primitives that we believe should be addressed in an IoT data management solution, and discuss how they are approached by the proposed solutions. We finally propose a data management framework for IoT that takes into consideration the discussed design elements and acts as a seed to a comprehensive IoT data management solution. The framework we propose adapts a federated, data- and sources-centric approach to link the diverse Things with their abundance of data to the potential applications and services that are envisioned for IoT. PMID:24240599

Reducing I/O variability using dynamic I/O path characterization in petascale storage systems

DOE PAGES

Son, Seung Woo; Sehrish, Saba; Liao, Wei-keng; ...

2016-11-01

In petascale systems with a million CPU cores, scalable and consistent I/O performance is becoming increasingly difficult to sustain mainly because of I/O variability. Furthermore, the I/O variability is caused by concurrently running processes/jobs competing for I/O or a RAID rebuild when a disk drive fails. We present a mechanism that stripes across a selected subset of I/O nodes with the lightest workload at runtime to achieve the highest I/O bandwidth available in the system. In this paper, we propose a probing mechanism to enable application-level dynamic file striping to mitigate I/O variability. We also implement the proposed mechanism inmore » the high-level I/O library that enables memory-to-file data layout transformation and allows transparent file partitioning using subfiling. Subfiling is a technique that partitions data into a set of files of smaller size and manages file access to them, making data to be treated as a single, normal file to users. Here, we demonstrate that our bandwidth probing mechanism can successfully identify temporally slower I/O nodes without noticeable runtime overhead. Experimental results on NERSC’s systems also show that our approach isolates I/O variability effectively on shared systems and improves overall collective I/O performance with less variation.« less

An Optimizing Compiler for Petascale I/O on Leadership Class Architectures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhary, Alok; Kandemir, Mahmut

In high-performance computing systems, parallel I/O architectures usually have very complex hierarchies with multiple layers that collectively constitute an I/O stack, including high-level I/O libraries such as PnetCDF and HDF5, I/O middleware such as MPI-IO, and parallel file systems such as PVFS and Lustre. Our project explored automated instrumentation and compiler support for I/O intensive applications. Our project made significant progress towards understanding the complex I/O hierarchies of high-performance storage systems (including storage caches, HDDs, and SSDs), and designing and implementing state-of-the-art compiler/runtime system technology that targets I/O intensive HPC applications that target leadership class machine. This final report summarizesmore » the major achievements of the project and also points out promising future directions.« less

Implementation of a Multichannel Serial Data Streaming Algorithm using the Xilinx Serial RapidIO Solution

NASA Technical Reports Server (NTRS)

Doxley, Charles A.

2016-01-01

In the current world of applications that use reconfigurable technology implemented on field programmable gate arrays (FPGAs), there is a need for flexible architectures that can grow as the systems evolve. A project has limited resources and a fixed set of requirements that development efforts are tasked to meet. Designers must develop robust solutions that practically meet the current customer demands and also have the ability to grow for future performance. This paper describes the development of a high speed serial data streaming algorithm that allows for transmission of multiple data channels over a single serial link. The technique has the ability to change to meet new applications developed for future design considerations. This approach uses the Xilinx Serial RapidIO LOGICORE Solution to implement a flexible infrastructure to meet the current project requirements with the ability to adapt future system designs.

A Long-Distance RF-Powered Sensor Node with Adaptive Power Management for IoT Applications.

PubMed

Pizzotti, Matteo; Perilli, Luca; Del Prete, Massimo; Fabbri, Davide; Canegallo, Roberto; Dini, Michele; Masotti, Diego; Costanzo, Alessandra; Franchi Scarselli, Eleonora; Romani, Aldo

2017-07-28

We present a self-sustained battery-less multi-sensor platform with RF harvesting capability down to -17 dBm and implementing a standard DASH7 wireless communication interface. The node operates at distances up to 17 m from a 2 W UHF carrier. RF power transfer allows operation when common energy scavenging sources (e.g., sun, heat, etc.) are not available, while the DASH7 communication protocol makes it fully compatible with a standard IoT infrastructure. An optimized energy-harvesting module has been designed, including a rectifying antenna (rectenna) and an integrated nano-power DC/DC converter performing maximum-power-point-tracking (MPPT). A nonlinear/electromagnetic co-design procedure is adopted to design the rectenna, which is optimized to operate at ultra-low power levels. An ultra-low power microcontroller controls on-board sensors and wireless protocol, to adapt the power consumption to the available detected power by changing wake-up policies. As a result, adaptive behavior can be observed in the designed platform, to the extent that the transmission data rate is dynamically determined by RF power. Among the novel features of the system, we highlight the use of nano-power energy harvesting, the implementation of specific hardware/software wake-up policies, optimized algorithms for best sampling rate implementation, and adaptive behavior by the node based on the power received.

A Long-Distance RF-Powered Sensor Node with Adaptive Power Management for IoT Applications

PubMed Central

del Prete, Massimo; Fabbri, Davide; Canegallo, Roberto; Dini, Michele; Costanzo, Alessandra

2017-01-01

We present a self-sustained battery-less multi-sensor platform with RF harvesting capability down to −17 dBm and implementing a standard DASH7 wireless communication interface. The node operates at distances up to 17 m from a 2 W UHF carrier. RF power transfer allows operation when common energy scavenging sources (e.g., sun, heat, etc.) are not available, while the DASH7 communication protocol makes it fully compatible with a standard IoT infrastructure. An optimized energy-harvesting module has been designed, including a rectifying antenna (rectenna) and an integrated nano-power DC/DC converter performing maximum-power-point-tracking (MPPT). A nonlinear/electromagnetic co-design procedure is adopted to design the rectenna, which is optimized to operate at ultra-low power levels. An ultra-low power microcontroller controls on-board sensors and wireless protocol, to adapt the power consumption to the available detected power by changing wake-up policies. As a result, adaptive behavior can be observed in the designed platform, to the extent that the transmission data rate is dynamically determined by RF power. Among the novel features of the system, we highlight the use of nano-power energy harvesting, the implementation of specific hardware/software wake-up policies, optimized algorithms for best sampling rate implementation, and adaptive behavior by the node based on the power received. PMID:28788084

Meeting the Challenge of Distributed Real-Time & Embedded (DRE) Systems

DTIC Science & Technology

2012-05-10

IP RTOS Middleware Middleware Services DRE Applications Operating Sys & Protocols Hardware & Networks Middleware Middleware Services DRE...Services COTS & standards-based middleware, language, OS , network, & hardware platforms • Real-time CORBA (TAO) middleware • ADAPTIVE Communication...SPLs) F-15 product variant A/V 8-B product variant F/A 18 product variant UCAV product variant Software Produce-Line Hardware (CPU, Memory, I/O) OS

Comparison of two intraosseous infusion systems for adult emergency medical use.

PubMed

Brenner, Thorsten; Bernhard, Michael; Helm, Matthias; Doll, Sara; Völkl, Alfred; Ganion, Nicole; Friedmann, Claudia; Sikinger, Marcus; Knapp, Jürgen; Martin, Eike; Gries, André

2008-09-01

The current guidelines of the European Resuscitation Council (ERC) stipulate that an intraosseous access should be placed if establishing a peripheral venous access for cardiopulmonary resuscitation (CPR) would involve delays. The aim of this study was therefore to compare a manual intraosseous infusion technique (MAN-IO) and a semi-automatic intraosseous infusion system (EZ-IO) using adult human cadavers as a model. After receiving verbal instruction and giving their written informed consent, the participants of the study were randomized into two groups (group I: MAN-IO, and group II: EZ-IO). In addition to the demographic data, the following were evaluated: (1) Number of attempts required to successfully place the infusion, (2) Insertion time, (3) Occurrence of technical complications and (4) User friendliness. Evaluation protocols from 84 study participants could be evaluated (MAN-IO: n=39 vs. EZ-IO: n=45). No significant differences were seen in the study participants' characteristics. Insertion times (MW+/-S.D.) of the respective successful attempts were comparable (MAN-IO: 33+/-28s vs. EZ-IO: 32+/-11s). When using the EZ-IO, the access was successfully established significantly more often on the first attempt (MAN-IO: 79.5% vs. EZ-IO: 97.8%; p<0.01). The EZ-IO was also found to have more advantages in terms of technical complications (MAN-IO: 15.4% vs. EZ-IO: 0.0%; p<0.01) and user friendliness (school grading system: MAN-IO: 1.9+/-0.7 vs. EZ-IO: 1.2+/-0.4; p<0.01). In an adult human cadaver model, the semi-automatic system was proven to be more effective. The EZ-IO gave more successful results, was associated with fewer technical complications, and is user friendlier.

Modeling the Internet of Things, Self-Organizing and Other Complex Adaptive Communication Networks: A Cognitive Agent-Based Computing Approach.

PubMed

Laghari, Samreen; Niazi, Muaz A

2016-01-01

Computer Networks have a tendency to grow at an unprecedented scale. Modern networks involve not only computers but also a wide variety of other interconnected devices ranging from mobile phones to other household items fitted with sensors. This vision of the "Internet of Things" (IoT) implies an inherent difficulty in modeling problems. It is practically impossible to implement and test all scenarios for large-scale and complex adaptive communication networks as part of Complex Adaptive Communication Networks and Environments (CACOONS). The goal of this study is to explore the use of Agent-based Modeling as part of the Cognitive Agent-based Computing (CABC) framework to model a Complex communication network problem. We use Exploratory Agent-based Modeling (EABM), as part of the CABC framework, to develop an autonomous multi-agent architecture for managing carbon footprint in a corporate network. To evaluate the application of complexity in practical scenarios, we have also introduced a company-defined computer usage policy. The conducted experiments demonstrated two important results: Primarily CABC-based modeling approach such as using Agent-based Modeling can be an effective approach to modeling complex problems in the domain of IoT. Secondly, the specific problem of managing the Carbon footprint can be solved using a multiagent system approach.

An Optimizing Compiler for Petascale I/O on Leadership-Class Architectures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kandemir, Mahmut Taylan; Choudary, Alok; Thakur, Rajeev

In high-performance computing (HPC), parallel I/O architectures usually have very complex hierarchies with multiple layers that collectively constitute an I/O stack, including high-level I/O libraries such as PnetCDF and HDF5, I/O middleware such as MPI-IO, and parallel file systems such as PVFS and Lustre. Our DOE project explored automated instrumentation and compiler support for I/O intensive applications. Our project made significant progress towards understanding the complex I/O hierarchies of high-performance storage systems (including storage caches, HDDs, and SSDs), and designing and implementing state-of-the-art compiler/runtime system technology that targets I/O intensive HPC applications that target leadership class machine. This final reportmore » summarizes the major achievements of the project and also points out promising future directions Two new sections in this report compared to the previous report are IOGenie and SSD/NVM-specific optimizations.« less

An Experimental Study of an Ultra-Mobile Vehicle for Off-Road Transportation

DTIC Science & Technology

1984-05-01

Adaptaive Hexapod Vehicle. M.S. thesis , The &io State University, August, 1982. 7. Tsai, C.K., Computer Control Design of an Energy-Efficient Leg, M.S...Applications, ASME, 1982. 9. Kao, M.L., A Reliable Multi-Microcomputer System for Real Time Control , M.S. thesis , The Ohio State University, December...13. Broerman, K.R., Development of a Proximity Sensor System for Foot Altitude Control of a Terrain-Adaptive Hexapod Robot, M.S. thesis , The Ohio State

Secure Data Aggregation Protocol for M2M Communications

DTIC Science & Technology

2015-03-24

networking and collaboration among various devices has experienced tremendous growth. To adapt to the trend, the concept of Internet of Things ( IoT ... IoTs ): Models, Algorithms, and Implementations, accepted Title: “Privacy-Preserving Time-Series Data Aggregation for Internet of Things ” Date...public release; distribution is unlimited. (5) Privacy-Preserving Time-Series Data Aggregation for Internet of Things Abstract In recent years, the

Modular HPC I/O characterization with Darshan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, Shane; Carns, Philip; Harms, Kevin

2016-11-13

Contemporary high-performance computing (HPC) applications encompass a broad range of distinct I/O strategies and are often executed on a number of different compute platforms in their lifetime. These large-scale HPC platforms employ increasingly complex I/O subsystems to provide a suitable level of I/O performance to applications. Tuning I/O workloads for such a system is nontrivial, and the results generally are not portable to other HPC systems. I/O profiling tools can help to address this challenge, but most existing tools only instrument specific components within the I/O subsystem that provide a limited perspective on I/O performance. The increasing diversity of scientificmore » applications and computing platforms calls for greater flexibililty and scope in I/O characterization.« less

Mic Flocks in the Cloud: Harnessing Mobile Ubiquitous Sensor Networks

NASA Astrophysics Data System (ADS)

Garces, M. A.; Christe, A.

2015-12-01

Smartphones provide a commercial, off-the-shelf solution to capture, store, analyze, and distribute infrasound using on-board or external microphones (mics) as well as on-board barometers. Free iOS infrasound apps can be readily downloaded from the Apple App Store, and Android versions are in progress. Infrasound propagates for great distances, has low sample rates, and provides a tractable pilot study scenario for open distributed sensor networks at regional and global scales using one of the most ubiquitous sensors on Earth - microphones. Data collection is no longer limited to selected vendors at exclusive prices: anybody on Earth can record and stream infrasound, and the diversity of recording systems and environments is rapidly expanding. Global deployment may be fast and easy (www.redvox.io), but comes with the cost of increasing data volume, velocity, variety, and complexity. Flocking - the collective motion of mobile agents - is a natural human response to threats or events of interest. Anticipating, modeling and harnessing flocking sensor topologies will be necessary for adaptive array and network processing. The increasing data quantity and complexity will exceed the processing capacity of human analysts and most research servers. We anticipate practical real-time applications will require the on-demand adaptive scalability and resources of the Cloud. Cloud architectures for such heterogeneous sensor networks will consider eventual integration into the Global Earth Observation System of Systems (GEOSS).

Inverse-optimized 3D conformal planning: Minimizing complexity while achieving equivalence with beamlet IMRT in multiple clinical sites

PubMed Central

Fraass, Benedick A.; Steers, Jennifer M.; Matuszak, Martha M.; McShan, Daniel L.

2012-01-01

Purpose: Inverse planned intensity modulated radiation therapy (IMRT) has helped many centers implement highly conformal treatment planning with beamlet-based techniques. The many comparisons between IMRT and 3D conformal (3DCRT) plans, however, have been limited because most 3DCRT plans are forward-planned while IMRT plans utilize inverse planning, meaning both optimization and delivery techniques are different. This work avoids that problem by comparing 3D plans generated with a unique inverse planning method for 3DCRT called inverse-optimized 3D (IO-3D) conformal planning. Since IO-3D and the beamlet IMRT to which it is compared use the same optimization techniques, cost functions, and plan evaluation tools, direct comparisons between IMRT and simple, optimized IO-3D plans are possible. Though IO-3D has some similarity to direct aperture optimization (DAO), since it directly optimizes the apertures used, IO-3D is specifically designed for 3DCRT fields (i.e., 1–2 apertures per beam) rather than starting with IMRT-like modulation and then optimizing aperture shapes. The two algorithms are very different in design, implementation, and use. The goals of this work include using IO-3D to evaluate how close simple but optimized IO-3D plans come to nonconstrained beamlet IMRT, showing that optimization, rather than modulation, may be the most important aspect of IMRT (for some sites). Methods: The IO-3D dose calculation and optimization functionality is integrated in the in-house 3D planning/optimization system. New features include random point dose calculation distributions, costlet and cost function capabilities, fast dose volume histogram (DVH) and plan evaluation tools, optimization search strategies designed for IO-3D, and an improved, reimplemented edge/octree calculation algorithm. The IO-3D optimization, in distinction to DAO, is designed to optimize 3D conformal plans (one to two segments per beam) and optimizes MLC segment shapes and weights with various user-controllable search strategies which optimize plans without beamlet or pencil beam approximations. IO-3D allows comparisons of beamlet, multisegment, and conformal plans optimized using the same cost functions, dose points, and plan evaluation metrics, so quantitative comparisons are straightforward. Here, comparisons of IO-3D and beamlet IMRT techniques are presented for breast, brain, liver, and lung plans. Results: IO-3D achieves high quality results comparable to beamlet IMRT, for many situations. Though the IO-3D plans have many fewer degrees of freedom for the optimization, this work finds that IO-3D plans with only one to two segments per beam are dosimetrically equivalent (or nearly so) to the beamlet IMRT plans, for several sites. IO-3D also reduces plan complexity significantly. Here, monitor units per fraction (MU/Fx) for IO-3D plans were 22%–68% less than that for the 1 cm × 1 cm beamlet IMRT plans and 72%–84% than the 0.5 cm × 0.5 cm beamlet IMRT plans. Conclusions: The unique IO-3D algorithm illustrates that inverse planning can achieve high quality 3D conformal plans equivalent (or nearly so) to unconstrained beamlet IMRT plans, for many sites. IO-3D thus provides the potential to optimize flat or few-segment 3DCRT plans, creating less complex optimized plans which are efficient and simple to deliver. The less complex IO-3D plans have operational advantages for scenarios including adaptive replanning, cases with interfraction and intrafraction motion, and pediatric patients. PMID:22755717

Carpet: Adaptive Mesh Refinement for the Cactus Framework

NASA Astrophysics Data System (ADS)

Schnetter, Erik; Hawley, Scott; Hawke, Ian

2016-11-01

Carpet is an adaptive mesh refinement and multi-patch driver for the Cactus Framework (ascl:1102.013). Cactus is a software framework for solving time-dependent partial differential equations on block-structured grids, and Carpet acts as driver layer providing adaptive mesh refinement, multi-patch capability, as well as parallelization and efficient I/O.

Interorganizational collaboration for health care between nongovernmental organizations (NGOs) in Pakistan.

PubMed

Gulzar, Laila; Henry, Beverly

2005-11-01

The complexity and cost of health systems requires innovative forms of organization to provide accessible health services of an acceptable quality and at an acceptable cost. Interorganizational collaboration (IoC) is an innovation to increase the availability of organizational resources, improve service effectiveness, and improve access to health care. In Pakistan, a weak health system and little collaboration limit access, especially of women and children, to health services. Many nongovernmental organizations (NGOs) provide primary health care to the very poor, and some appear to collaborate to varying degrees; however, this has not been systematically analyzed. The purpose of this qualitative research, the first scientific study of collaboration between NGOs providing health services in Pakistan, was to describe collaboration between three pairs of NGOs providing community-based health services to women in Karachi. A long-term goal is to build a basis for future research linking IoC to access to health care and health outcomes. Findings indicated that collaboration was strongest when there was willingness to cooperate, a need for expertise and funds, and adaptive efficiency. In Pakistan's complex social environment, collaboration tended to be stronger when there was fairly high organizational formalization. Broader IoC appears to be positively associated with women's access to health care. Recommendations are made for future research, education, and management.

A Resource Service Model in the Industrial IoT System Based on Transparent Computing.

PubMed

Li, Weimin; Wang, Bin; Sheng, Jinfang; Dong, Ke; Li, Zitong; Hu, Yixiang

2018-03-26

The Internet of Things (IoT) has received a lot of attention, especially in industrial scenarios. One of the typical applications is the intelligent mine, which actually constructs the Six-Hedge underground systems with IoT platforms. Based on a case study of the Six Systems in the underground metal mine, this paper summarizes the main challenges of industrial IoT from the aspects of heterogeneity in devices and resources, security, reliability, deployment and maintenance costs. Then, a novel resource service model for the industrial IoT applications based on Transparent Computing (TC) is presented, which supports centralized management of all resources including operating system (OS), programs and data on the server-side for the IoT devices, thus offering an effective, reliable, secure and cross-OS IoT service and reducing the costs of IoT system deployment and maintenance. The model has five layers: sensing layer, aggregation layer, network layer, service and storage layer and interface and management layer. We also present a detailed analysis on the system architecture and key technologies of the model. Finally, the efficiency of the model is shown by an experiment prototype system.

A Resource Service Model in the Industrial IoT System Based on Transparent Computing

PubMed Central

Wang, Bin; Sheng, Jinfang; Dong, Ke; Li, Zitong; Hu, Yixiang

2018-01-01

The Internet of Things (IoT) has received a lot of attention, especially in industrial scenarios. One of the typical applications is the intelligent mine, which actually constructs the Six-Hedge underground systems with IoT platforms. Based on a case study of the Six Systems in the underground metal mine, this paper summarizes the main challenges of industrial IoT from the aspects of heterogeneity in devices and resources, security, reliability, deployment and maintenance costs. Then, a novel resource service model for the industrial IoT applications based on Transparent Computing (TC) is presented, which supports centralized management of all resources including operating system (OS), programs and data on the server-side for the IoT devices, thus offering an effective, reliable, secure and cross-OS IoT service and reducing the costs of IoT system deployment and maintenance. The model has five layers: sensing layer, aggregation layer, network layer, service and storage layer and interface and management layer. We also present a detailed analysis on the system architecture and key technologies of the model. Finally, the efficiency of the model is shown by an experiment prototype system. PMID:29587450

Design theory, modelling and the application for the Internet of Things service

NASA Astrophysics Data System (ADS)

Shang, Xiaopu; Zhang, Runtong; Zhu, Xiaomin; Zhou, Quan

2016-03-01

The Internet of Things (IoT) makes it possible for us to sense the physical world and locate objects in it using the enabling technologies associated with IoT. Compared with traditional information systems, IoT enabling technologies can help acquire real-time data necessary for managing enterprise business process. An IoT system should have an ability beyond integrating enabling technologies and traditional information systems that are only used to access environmental data. This paper begins with a literature review of IoT-related issues and a discussion of the difference between traditional information service and IoT service. Three principles for IoT service design from the perceptive of service classification, coordination and compatibility are proposed. The paper also proposes a utility model for resource allocation in order to improve IoT service performance, and an application involving a cold chain visibility platform is given to illustrate our research.

Proceedings of the 2010 AFMS Medical Research Symposium. Volume 3. Enroute Track: Abstracts and Presentations

DTIC Science & Technology

2011-03-15

comparison of proximal tibia, proximal humerus and distal femur infusion rates under high pressure using the EZ-IO Intraosseous device on an adult...contaminated complex musculoskeletal wounds. METHODS: We adapted a previously characterized caprine model. Under anesthesia , complex musculoskeletal...of proximal tibia, proximal humerus and distal femur infusion rates under high pressure using the EZ-IO Intraosseous device on an adult swine model

Effects of inferior olive lesion on fear-conditioned bradycardia

PubMed Central

Kotajima, Hiroko; Sakai, Kazuhisa; Hashikawa, Tsutomu

2014-01-01

The inferior olive (IO) sends excitatory inputs to the cerebellar cortex and cerebellar nuclei through the climbing fibers. In eyeblink conditioning, a model of motor learning, the inactivation of or a lesion in the IO impairs the acquisition or expression of conditioned eyeblink responses. Additionally, climbing fibers originating from the IO are believed to transmit the unconditioned stimulus to the cerebellum in eyeblink conditioning. Studies using fear-conditioned bradycardia showed that the cerebellum is associated with adaptive control of heart rate. However, the role of inputs from the IO to the cerebellum in fear-conditioned bradycardia has not yet been investigated. To examine this possible role, we tested fear-conditioned bradycardia in mice by selective disruption of the IO using 3-acetylpyridine. In a rotarod test, mice with an IO lesion were unable to remain on the rod. The number of neurons of IO nuclei in these mice was decreased to ∼40% compared with control mice. Mice with an IO lesion did not show changes in the mean heart rate or in heart rate responses to a conditioned stimulus, or in their responses to a painful stimulus in a tail-flick test. However, they did show impairment of the acquisition/expression of conditioned bradycardia and attenuation of heart rate responses to a pain stimulus used as an unconditioned stimulus. These results indicate that the IO inputs to the cerebellum play a key role in the acquisition/expression of conditioned bradycardia. PMID:24784584

Neural network with dynamically adaptable neurons

NASA Technical Reports Server (NTRS)

Tawel, Raoul (Inventor)

1994-01-01

This invention is an adaptive neuron for use in neural network processors. The adaptive neuron participates in the supervised learning phase of operation on a co-equal basis with the synapse matrix elements by adaptively changing its gain in a similar manner to the change of weights in the synapse IO elements. In this manner, training time is decreased by as much as three orders of magnitude.

BESIII physical offline data analysis on virtualization platform

NASA Astrophysics Data System (ADS)

Huang, Q.; Li, H.; Kan, B.; Shi, J.; Lei, X.

2015-12-01

In this contribution, we present an ongoing work, which aims at benefiting BESIII computing system for higher resource utilization and more efficient job operations brought by cloud and virtualization technology with Openstack and KVM. We begin with the architecture of BESIII offline software to understand how it works. We mainly report the KVM performance evaluation and optimization from various factors in hardware and kernel. Experimental results show the CPU performance penalty of KVM can be approximately decreased to 3%. In addition, the performance comparison between KVM and physical machines in aspect of CPU, disk IO and network IO is also presented. Finally, we present our development work, an adaptive cloud scheduler, which allocates and reclaims VMs dynamically according to the status of TORQUE queue and the size of resource pool to improve resource utilization and job processing efficiency.

Fast and efficient compression of floating-point data.

PubMed

Lindstrom, Peter; Isenburg, Martin

2006-01-01

Large scale scientific simulation codes typically run on a cluster of CPUs that write/read time steps to/from a single file system. As data sets are constantly growing in size, this increasingly leads to I/O bottlenecks. When the rate at which data is produced exceeds the available I/O bandwidth, the simulation stalls and the CPUs are idle. Data compression can alleviate this problem by using some CPU cycles to reduce the amount of data needed to be transfered. Most compression schemes, however, are designed to operate offline and seek to maximize compression, not throughput. Furthermore, they often require quantizing floating-point values onto a uniform integer grid, which disqualifies their use in applications where exact values must be retained. We propose a simple scheme for lossless, online compression of floating-point data that transparently integrates into the I/O of many applications. A plug-in scheme for data-dependent prediction makes our scheme applicable to a wide variety of data used in visualization, such as unstructured meshes, point sets, images, and voxel grids. We achieve state-of-the-art compression rates and speeds, the latter in part due to an improved entropy coder. We demonstrate that this significantly accelerates I/O throughput in real simulation runs. Unlike previous schemes, our method also adapts well to variable-precision floating-point and integer data.

Using IoT Device Technology in Spacecraft Checkout Systems

NASA Astrophysics Data System (ADS)

Plummer, Chris

2015-09-01

The Internet of Things (IoT) has become a common theme in both the technical and popular press in recent years because many of the enabling technologies that are required to make IoT a reality have now matured. Those technologies are revolutionising the way industrial systems and products are developed because they offer significant advantages over older technologies. This paper looks at how IoT device technology can be used in spacecraft checkout systems to achieve smaller, more capable, and more scalable solutions than are currently available. It covers the use of IoT device technology for classical spacecraft test systems as well as for hardware-in-the-loop simulation systems used to support spacecraft checkout.

Automatic Identification of Application I/O Signatures from Noisy Server-Side Traces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Yang; Gunasekaran, Raghul; Ma, Xiaosong

2014-01-01

Competing workloads on a shared storage system cause I/O resource contention and application performance vagaries. This problem is already evident in today s HPC storage systems and is likely to become acute at exascale. We need more interaction between application I/O requirements and system software tools to help alleviate the I/O bottleneck, moving towards I/O-aware job scheduling. However, this requires rich techniques to capture application I/O characteristics, which remain evasive in production systems. Traditionally, I/O characteristics have been obtained using client-side tracing tools, with drawbacks such as non-trivial instrumentation/development costs, large trace traffic, and inconsistent adoption. We present a novelmore » approach, I/O Signature Identifier (IOSI), to characterize the I/O behavior of data-intensive applications. IOSI extracts signatures from noisy, zero-overhead server-side I/O throughput logs that are already collected on today s supercomputers, without interfering with the compiling/execution of applications. We evaluated IOSI using the Spider storage system at Oak Ridge National Laboratory, the S3D turbulence application (running on 18,000 Titan nodes), and benchmark-based pseudo-applications. Through our ex- periments we confirmed that IOSI effectively extracts an application s I/O signature despite significant server-side noise. Compared to client-side tracing tools, IOSI is transparent, interface-agnostic, and incurs no overhead. Compared to alternative data alignment techniques (e.g., dynamic time warping), it offers higher signature accuracy and shorter processing time.« less

Of Rings and Volcanoes

NASA Astrophysics Data System (ADS)

2002-01-01

Fine Images of Saturn and Io with VLT NAOS-CONICA Summary With its new NAOS-CONICA Adaptive Optics facility, the ESO Very Large Telescope (VLT) at the Paranal Observatory has recently obtained impressive views of the giant planet Saturn and Io, the volcanic moon of Jupiter. They show the two objects with great clarity, unprecedented for a ground-based telescope. The photos were made during the ongoing commissioning of this major VLT instrument, while it is being optimized and prepared for regular observations that will start later this year. PR Photo 04a/02 : VLT NAOS-CONICA photo of the giant planet Saturn (composite H+K band image). PR Photo 04b/02 : The Jovian moon Io (Br-gamma image). PR Photo 04c/02 : The Jovian moon Io (composite Br-gamma + L' image). Commissioning of NAOS-CONICA progresses "First light" for the new NAOS-CONICA Adaptive Optics facility on the 8.2-m VLT YEPUN telescope at the Paranal Observatory was achieved in November 2001, cf. ESO PR 25/01. A second phase of the "commissioning" of the new facility began on January 22, 2002, now involving specialized observing modes and with the aim of trimming it to maximum performance before it is made available to the astronomers later this year. During this demanding and delicate work, more test images have been made of various astronomical objects [1]. Some of these show selected solar system bodies, for which the excellent image sharpness achievable with this new instrument is of special significance. In fact, the VLT photos of the giant planet Saturn and Io, the innermost of Jupiter's four large moons, are among the sharpest ever obtained from the ground . They even compare well with some photos obtained from space, as can be seen via the related weblinks indicated below. The raw NAOS-CONICA data from which these images shown in this Photo Release were produced are now available via the public VLT Science Archive Facility [2]. The NAOS adaptive optics corrector was built, under an ESO contract, by the Office National d'Etudes et de Recherches Aérospatiales (ONERA) , Laboratoire d'Astrophysique de Grenoble (LAOG) and the DESPA and DASGAL laboratories of the Observatoire de Paris in France, in collaboration with ESO. The CONICA infra-red camera was built, under an ESO contract, by the Max-Planck-Institut für Astronomie (MPIA) (Heidelberg) and the Max-Planck Institut für Extraterrestrische Physik (MPE) (Garching) in Germany, in collaboration with ESO. Saturn - Lord of the rings ESO PR Photo 04a/02 ESO PR Photo 04a/02 [Preview - JPEG: 460 x 400 pix - 54k] [Normal - JPEG: 1034 x 800 pix - 200k] Caption : PR Photo 04a/02 shows the giant planet Saturn, as observed with the VLT NAOS-CONICA Adaptive Optics instrument on December 8, 2001; the distance was 1209 million km. It is a composite of exposures in two near-infrared wavebands (H and K) and displays well the intricate, banded structure of the planetary atmosphere and the rings. Note also the dark spot at the south pole at the bottom of the image. One of the moons, Tethys, is visible as a small point of light below the planet. It was used to guide the telescope and to perform the adaptive optics "refocussing" for this observation. More details in the text. Technical information about this photo is available below. This NAOS/CONICA image of Saturn ( PR Photo 04a/02 ), the second-largest planet in the solar system, was obtained at a time when Saturn was close to summer solstice in the southern hemisphere. At this moment, the tilt of the rings was about as large as it can be, allowing the best possible view of the planet's South Pole. That area was on Saturn's night side in 1982 and could therefore not be photographed during the Voyager encounter. The dark spot close to the South Pole is a remarkable structure that measures approximately 300 km across. It was only recently observed in visible light from the ground with a telescope at the Pic du Midi Observatory in the Pyrenees (France) - this is the first infrared image to show it. The bright spot close to the equator is the remnant of a giant storm in Saturn's extended atmosphere that has lasted more than 5 years. The present photo provides what is possibly the sharpest view of the ring system ever achieved from a ground-based observatory . Many structures are visible, the most obvious being the main ring sections, the inner C-region (here comparatively dark), the middle B-region (here relatively bright) and the outer A-region, and also the obvious dark "divisions", including the well-known, broad Cassini division between the A- and B-regions, as well as the Encke division close to the external edge of the A-region and the Colombo division in the C-region. Moreover, many narrow rings can be seen at this high image resolution , in particular within the C-region - they may be compared with those seen by the Voyager spacecraft during the flybys, cf. the weblinks below. This image demonstrates the capability of NAOS-CONICA to observe also extended objects with excellent spatial resolution. It is a composite of four short-exposure images taken through the near-infrared H (wavelength 1.6 µm) and K (2.2 µm) filters. This observation was particularly difficult because of the motion of Saturn during the exposure. To provide the best possible images, the Adaptive Optics system of NAOS was pointed towards the Saturnian moon Tethys , while the image of Saturn was kept at a fixed position on the CONICA detector by means of "differential tracking" (compensating for the different motions in the sky of Saturn and Tethys). This is also why the (faint) image of Tethys - visible south of Saturn (i.e., below the planet in PR Photo 04a/02 ) - appears slightly trailed. Io - volcanoes and sulphur ESO PR Photo 04b/02 ESO PR Photo 04b/02 [Preview - JPEG: 400 x 478 pix - 39k] [Normal - JPEG: 800 x 955 pix - 112k] ESO PR Photo 04c/02 ESO PR Photo 04c/02 [Preview - JPEG: 400 x 469 pix - 58k] [Normal - JPEG: 800 x 937 pix - 368k] Caption : PR Photo 04b/02 shows Io , the volcanic moon of Jupiter, as imaged with the VLT NAOS-CONICA Adaptive Optics instrument on December 5, 2001, through a near-infrared, narrow optical filter (Brackett-gamma at wavelength 2.166 µm). Despite the small angular diameter of Io , about 1.2 arcsec, many features are visible at this excellent optical resolution. PR Photo 04c/02 is a composite of the same exposure with another obtained at a longer wavelength (L'-filter at 3.8 µm), with a latitude-longitude grid superposed and some of the main surface features identified. Technical information about these photos is available below. Io has a diameter of 3660 km and orbits Jupiter at a mean distance of 422,000 km - one revolution takes 42.5 hours. Like the Earth's moon, it always turns the same side towards the planet. As shown by the Voyager spacecraft in 1979, its surface is covered by active volcanoes and lava fields - it is in fact the most volcanic place known in the solar system. Due to this activity, Io's surface is continuously reshaped. The features now seen are all correspondingly young, with a mean age of the order of 1 million years only. The variations in appearance and colour are due to different volcanic deposits of sulphur compounds. The cause of all this activity is Jupiter's strong gravitational pull that leads to enormous stresses inside Io and related heating of the entire moon. PR Photo 04b/02 is a near-infrared NAOS-CONICA image of Io , obtained on December 5, 2001, through a narrow optical filter at wavelength 2.166 µm. The excellent image resolution makes it possible to identify many features on the surface. Some of these are volcanoes, others correspond to lava fields between these. PR Photo 04c/02 is a composite of that image and another obtained at longer wavelength (3.8 µm). A latitute-longitude grid has been superposed, with the most prominent features identified by name, including some of the large volcanoes and sulphurus plains on this very active moon. Io has been observed with the NASA Galileo spacecraft since 1996 at higher resolution in the visible and infrared, especially during close encounters with the satellite (a link to Galileo maps of Io is available below). However, this NAOS image fills a gap in the surface coverage of the infrared images from Galileo. The capability of NAOS/CONICA to map Io in the infrared at the present high image resolution will allow astronomers to continue the survey of the volcanic activity and to monitor regularly the related surface processes . Related sites The following links point to a number of prominent photos of these two objects that were obtained elsewhere. Saturn Voyager images : http://vraptor.jpl.nasa.gov/voyager/vgrsat_img.html HST images : http://hubble.stsci.edu/news_.and._views/pr.cgi.2001+15 Pic du Midi images : http://www.bdl.fr/s2p/saturne.html IfA-CFHT : http://www.ifa.hawaii.edu/ao/images/solarsys/new/new.html Io NASA/Galileo site : http://www.jpl.nasa.gov/galileo/moons/io.html Volcanoes on Io : http://volcano.und.nodak.edu/vwdocs/planet_volcano/Io/Overview.html HST image of Io : http://hubble.stsci.edu/news_.and._views/pr.cgi.1997+21 Keck I image of Io : http://www.astro.caltech.edu/mirror/keck/realpublic/inst/ao/Io/IoSnapshot.jpg Galileo and Voyager maps of Io : http://www.lowell.edu/users/ijw/maps/ (also with names of surface features) Notes [1]: The following astronomers and engineers from ESO and the partner institutes have participated in the current commissioning observations of Saturn and Io with NAOS-CONICA: Wolfgang Brandner, Jean-Gabriel Cuby, Pierre Drossart, Thierry Fusco, Eric Gendron, Markus Hartung, Norbert Hubin, François Lacombe, Anne-Marie Lagrange, Rainer Lenzen, David Mouillet, Claire Moutou, Gérard Rousset, Jason Spyromilio and Gérard Zins . [2]: New archive users may register via the ESO/ST-ECF Archive Registration Form. Technical information about the photos PR Photo 04a/02 is based on four exposures, obtained with VLT YEPUN and NAOS-CONICA on December 8, 2001 (UT). Two of these were made with an H-band filter (10 sec exposure each, wavelength 1.6 µm) and two with a K-band filter (12 sec each, 2.2 µm). The satellite Tethys (diameter 1070 km, orbiting Saturn at a distance of approx. 295,000 km) served as reference source for the Adaptive Optics corrections and the telescope was offset guided to compensate for the differential motion. The frames were reduced in the normal way with classical flats, dark and bias correction. No convolution was made before the two colours were combined to produce the image shown. At the time of the exposure, Saturn was 8.80 AU from the Earth. With a diameter of approx. 120,000 km, its disk subtended an angle of 20.6 arcsec. The nominal resolution of the NAOS-CONICA image, about 0.07 arcsec, thus corresponds to 410 km at Saturn. PR Photo 04b/02 is a reproduction based on a total exposure of 230 sec with VLT YEPUN and NAOS-CONICA on December 5, 2001, made through a Brackett-gamma filter centred at 2.166 µm. The resulting image resolution is 0.068 arcsec. At the moment of the exposure, the distance from the Earth to Io was about 641 million km (4.29 AU) and the image resolution therefore corresponds to approx. 210 km on the surface of the moon. PR Photo 04c/02 is based on a combination of the Brackett-gamma (here rendered as blue) with an L' frame (total exposure 4.2 sec; 3.800 µm; red), superposed with a coordinate grid and with some of the major surface features identified. The grid was produced with tools available at the website of the Institut de Mecanique Celeste et de Calcul des Ephemerides.

On I/O Virtualization Management

NASA Astrophysics Data System (ADS)

Danciu, Vitalian A.; Metzker, Martin G.

The quick adoption of virtualization technology in general and the advent of the Cloud business model entail new requirements on the structure and the configuration of back-end I/O systems. Several approaches to virtualization of I/O links are being introduced, which aim at implementing a more flexible I/O channel configuration without compromising performance. While previously the management of I/O devices could be limited to basic technical requirments (e.g. the establishment and termination of fixed-point links), the additional flexibility carries in its wake additional management requirements on the representation and control of I/O sub-systems.

Extending Comprehensive Maritime Awareness to Disconnected Vessels and Users

DTIC Science & Technology

2007-09-01

system shall: 7. Provide flexible , scalable, and tailorable techniques, processes, and procedures that can be adapted rapidly and securely 8...PS (1 2- 21 ) SO W (2 2- 23 ) St ak eh ol de r C om m un ic at io ns (2 4) Provide secure connection of Node 5 to CMA Node 4 1,4,5 8 19 Provide...6 7 13,24 Provide flexible system - allow user display customization 6 7 13 Provide accurate data and info 2,3 16, 20, 24 Provide accurate local data

Modeling the Internet of Things, Self-Organizing and Other Complex Adaptive Communication Networks: A Cognitive Agent-Based Computing Approach

PubMed Central

2016-01-01

Background Computer Networks have a tendency to grow at an unprecedented scale. Modern networks involve not only computers but also a wide variety of other interconnected devices ranging from mobile phones to other household items fitted with sensors. This vision of the "Internet of Things" (IoT) implies an inherent difficulty in modeling problems. Purpose It is practically impossible to implement and test all scenarios for large-scale and complex adaptive communication networks as part of Complex Adaptive Communication Networks and Environments (CACOONS). The goal of this study is to explore the use of Agent-based Modeling as part of the Cognitive Agent-based Computing (CABC) framework to model a Complex communication network problem. Method We use Exploratory Agent-based Modeling (EABM), as part of the CABC framework, to develop an autonomous multi-agent architecture for managing carbon footprint in a corporate network. To evaluate the application of complexity in practical scenarios, we have also introduced a company-defined computer usage policy. Results The conducted experiments demonstrated two important results: Primarily CABC-based modeling approach such as using Agent-based Modeling can be an effective approach to modeling complex problems in the domain of IoT. Secondly, the specific problem of managing the Carbon footprint can be solved using a multiagent system approach. PMID:26812235

File concepts for parallel I/O

NASA Technical Reports Server (NTRS)

Crockett, Thomas W.

1989-01-01

The subject of input/output (I/O) was often neglected in the design of parallel computer systems, although for many problems I/O rates will limit the speedup attainable. The I/O problem is addressed by considering the role of files in parallel systems. The notion of parallel files is introduced. Parallel files provide for concurrent access by multiple processes, and utilize parallelism in the I/O system to improve performance. Parallel files can also be used conventionally by sequential programs. A set of standard parallel file organizations is proposed, organizations are suggested, using multiple storage devices. Problem areas are also identified and discussed.

Active Storage with Analytics Capabilities and I/O Runtime System for Petascale Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhary, Alok

Computational scientists must understand results from experimental, observational and computational simulation generated data to gain insights and perform knowledge discovery. As systems approach the petascale range, problems that were unimaginable a few years ago are within reach. With the increasing volume and complexity of data produced by ultra-scale simulations and high-throughput experiments, understanding the science is largely hampered by the lack of comprehensive I/O, storage, acceleration of data manipulation, analysis, and mining tools. Scientists require techniques, tools and infrastructure to facilitate better understanding of their data, in particular the ability to effectively perform complex data analysis, statistical analysis and knowledgemore » discovery. The goal of this work is to enable more effective analysis of scientific datasets through the integration of enhancements in the I/O stack, from active storage support at the file system layer to MPI-IO and high-level I/O library layers. We propose to provide software components to accelerate data analytics, mining, I/O, and knowledge discovery for large-scale scientific applications, thereby increasing productivity of both scientists and the systems. Our approaches include 1) design the interfaces in high-level I/O libraries, such as parallel netCDF, for applications to activate data mining operations at the lower I/O layers; 2) Enhance MPI-IO runtime systems to incorporate the functionality developed as a part of the runtime system design; 3) Develop parallel data mining programs as part of runtime library for server-side file system in PVFS file system; and 4) Prototype an active storage cluster, which will utilize multicore CPUs, GPUs, and FPGAs to carry out the data mining workload.« less

Server-side Log Data Analytics for I/O Workload Characterization and Coordination on Large Shared Storage Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Y.; Gunasekaran, Raghul; Ma, Xiaosong

2016-01-01

Inter-application I/O contention and performance interference have been recognized as severe problems. In this work, we demonstrate, through measurement from Titan (world s No. 3 supercomputer), that high I/O variance co-exists with the fact that individual storage units remain under-utilized for the majority of the time. This motivates us to propose AID, a system that performs automatic application I/O characterization and I/O-aware job scheduling. AID analyzes existing I/O traffic and batch job history logs, without any prior knowledge on applications or user/developer involvement. It identifies the small set of I/O-intensive candidates among all applications running on a supercomputer and subsequentlymore » mines their I/O patterns, using more detailed per-I/O-node traffic logs. Based on such auto- extracted information, AID provides online I/O-aware scheduling recommendations to steer I/O-intensive applications away from heavy ongoing I/O activities. We evaluate AID on Titan, using both real applications (with extracted I/O patterns validated by contacting users) and our own pseudo-applications. Our results confirm that AID is able to (1) identify I/O-intensive applications and their detailed I/O characteristics, and (2) significantly reduce these applications I/O performance degradation/variance by jointly evaluating out- standing applications I/O pattern and real-time system l/O load.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamblin, T; de Supinski, B R; Schulz, M

Good load balance is crucial on very large parallel systems, but the most sophisticated algorithms introduce dynamic imbalances through adaptation in domain decomposition or use of adaptive solvers. To observe and diagnose imbalance, developers need system-wide, temporally-ordered measurements from full-scale runs. This potentially requires data collection from multiple code regions on all processors over the entire execution. Doing this instrumentation naively can, in combination with the application itself, exceed available I/O bandwidth and storage capacity, and can induce severe behavioral perturbations. We present and evaluate a novel technique for scalable, low-error load balance measurement. This uses a parallel wavelet transformmore » and other parallel encoding methods. We show that our technique collects and reconstructs system-wide measurements with low error. Compression time scales sublinearly with system size and data volume is several orders of magnitude smaller than the raw data. The overhead is low enough for online use in a production environment.« less

VisIO: enabling interactive visualization of ultra-scale, time-series data via high-bandwidth distributed I/O systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Christopher J; Ahrens, James P; Wang, Jun

2010-10-15

Petascale simulations compute at resolutions ranging into billions of cells and write terabytes of data for visualization and analysis. Interactive visuaUzation of this time series is a desired step before starting a new run. The I/O subsystem and associated network often are a significant impediment to interactive visualization of time-varying data; as they are not configured or provisioned to provide necessary I/O read rates. In this paper, we propose a new I/O library for visualization applications: VisIO. Visualization applications commonly use N-to-N reads within their parallel enabled readers which provides an incentive for a shared-nothing approach to I/O, similar tomore » other data-intensive approaches such as Hadoop. However, unlike other data-intensive applications, visualization requires: (1) interactive performance for large data volumes, (2) compatibility with MPI and POSIX file system semantics for compatibility with existing infrastructure, and (3) use of existing file formats and their stipulated data partitioning rules. VisIO, provides a mechanism for using a non-POSIX distributed file system to provide linear scaling of 110 bandwidth. In addition, we introduce a novel scheduling algorithm that helps to co-locate visualization processes on nodes with the requested data. Testing using VisIO integrated into Para View was conducted using the Hadoop Distributed File System (HDFS) on TACC's Longhorn cluster. A representative dataset, VPIC, across 128 nodes showed a 64.4% read performance improvement compared to the provided Lustre installation. Also tested, was a dataset representing a global ocean salinity simulation that showed a 51.4% improvement in read performance over Lustre when using our VisIO system. VisIO, provides powerful high-performance I/O services to visualization applications, allowing for interactive performance with ultra-scale, time-series data.« less

Energy Efficient IoT Data Collection in Smart Cities Exploiting D2D Communications.

PubMed

Orsino, Antonino; Araniti, Giuseppe; Militano, Leonardo; Alonso-Zarate, Jesus; Molinaro, Antonella; Iera, Antonio

2016-06-08

Fifth Generation (5G) wireless systems are expected to connect an avalanche of "smart" objects disseminated from the largest "Smart City" to the smallest "Smart Home". In this vision, Long Term Evolution-Advanced (LTE-A) is deemed to play a fundamental role in the Internet of Things (IoT) arena providing a large coherent infrastructure and a wide wireless connectivity to the devices. However, since LTE-A was originally designed to support high data rates and large data size, novel solutions are required to enable an efficient use of radio resources to convey small data packets typically exchanged by IoT applications in "smart" environments. On the other hand, the typically high energy consumption required by cellular communications is a serious obstacle to large scale IoT deployments under cellular connectivity as in the case of Smart City scenarios. Network-assisted Device-to-Device (D2D) communications are considered as a viable solution to reduce the energy consumption for the devices. The particular approach presented in this paper consists in appointing one of the IoT smart devices as a collector of all data from a cluster of objects using D2D links, thus acting as an aggregator toward the eNodeB. By smartly adapting the Modulation and Coding Scheme (MCS) on the communication links, we will show it is possible to maximize the radio resource utilization as a function of the total amount of data to be sent. A further benefit that we will highlight is the possibility to reduce the transmission power when a more robust MCS is adopted. A comprehensive performance evaluation in a wide set of scenarios will testify the achievable gains in terms of energy efficiency and resource utilization in the envisaged D2D-based IoT data collection.

Energy Efficient IoT Data Collection in Smart Cities Exploiting D2D Communications

PubMed Central

Orsino, Antonino; Araniti, Giuseppe; Militano, Leonardo; Alonso-Zarate, Jesus; Molinaro, Antonella; Iera, Antonio

2016-01-01

Fifth Generation (5G) wireless systems are expected to connect an avalanche of “smart” objects disseminated from the largest “Smart City” to the smallest “Smart Home”. In this vision, Long Term Evolution-Advanced (LTE-A) is deemed to play a fundamental role in the Internet of Things (IoT) arena providing a large coherent infrastructure and a wide wireless connectivity to the devices. However, since LTE-A was originally designed to support high data rates and large data size, novel solutions are required to enable an efficient use of radio resources to convey small data packets typically exchanged by IoT applications in “smart” environments. On the other hand, the typically high energy consumption required by cellular communications is a serious obstacle to large scale IoT deployments under cellular connectivity as in the case of Smart City scenarios. Network-assisted Device-to-Device (D2D) communications are considered as a viable solution to reduce the energy consumption for the devices. The particular approach presented in this paper consists in appointing one of the IoT smart devices as a collector of all data from a cluster of objects using D2D links, thus acting as an aggregator toward the eNodeB. By smartly adapting the Modulation and Coding Scheme (MCS) on the communication links, we will show it is possible to maximize the radio resource utilization as a function of the total amount of data to be sent. A further benefit that we will highlight is the possibility to reduce the transmission power when a more robust MCS is adopted. A comprehensive performance evaluation in a wide set of scenarios will testify the achievable gains in terms of energy efficiency and resource utilization in the envisaged D2D-based IoT data collection. PMID:27338385

An IoT-Based Solution for Monitoring a Fleet of Educational Buildings Focusing on Energy Efficiency.

PubMed

Amaxilatis, Dimitrios; Akrivopoulos, Orestis; Mylonas, Georgios; Chatzigiannakis, Ioannis

2017-10-10

Raising awareness among young people and changing their behaviour and habits concerning energy usage is key to achieving sustained energy saving. Additionally, young people are very sensitive to environmental protection so raising awareness among children is much easier than with any other group of citizens. This work examines ways to create an innovative Information & Communication Technologies (ICT) ecosystem (including web-based, mobile, social and sensing elements) tailored specifically for school environments, taking into account both the users (faculty, staff, students, parents) and school buildings, thus motivating and supporting young citizens' behavioural change to achieve greater energy efficiency. A mixture of open-source IoT hardware and proprietary platforms on the infrastructure level, are currently being utilized for monitoring a fleet of 18 educational buildings across 3 countries, comprising over 700 IoT monitoring points. Hereon presented is the system's high-level architecture, as well as several aspects of its implementation, related to the application domain of educational building monitoring and energy efficiency. The system is developed based on open-source technologies and services in order to make it capable of providing open IT-infrastructure and support from different commercial hardware/sensor vendors as well as open-source solutions. The system presented can be used to develop and offer new app-based solutions that can be used either for educational purposes or for managing the energy efficiency of the building. The system is replicable and adaptable to settings that may be different than the scenarios envisioned here (e.g., targeting different climate zones), different IT infrastructures and can be easily extended to accommodate integration with other systems. The overall performance of the system is evaluated in real-world environment in terms of scalability, responsiveness and simplicity.

Intraoral Scanner Technologies: A Review to Make a Successful Impression

PubMed Central

Richert, Raphaël; Goujat, Alexis; Venet, Laurent; Viguie, Gilbert; Viennot, Stéphane; Robinson, Philip; Farges, Jean-Christophe; Fages, Michel

2017-01-01

To overcome difficulties associated with conventional techniques, impressions with IOS (intraoral scanner) and CAD/CAM (computer-aided design and manufacturing) technologies were developed for dental practice. The last decade has seen an increasing number of optical IOS devices, and these are based on different technologies; the choice of which may impact on clinical use. To allow informed choice before purchasing or renewing an IOS, this article summarizes first the technologies currently used (light projection, distance object determination, and reconstruction). In the second section, the clinical considerations of each strategy such as handling, learning curve, powdering, scanning paths, tracking, and mesh quality are discussed. The last section is dedicated to the accuracy of files and of the intermaxillary relationship registered with IOS as the rendering of files in the graphical user interface is often misleading. This overview leads to the conclusion that the current IOS is adapted for a common practice, although differences exist between the technologies employed. An important aspect highlighted in this review is the reduction in the volume of hardware which has led to an increase in the importance of software-based technologies. PMID:29065652

Review on open source operating systems for internet of things

NASA Astrophysics Data System (ADS)

Wang, Zhengmin; Li, Wei; Dong, Huiliang

2017-08-01

Internet of Things (IoT) is an environment in which everywhere and every device became smart in a smart world. Internet of Things is growing vastly; it is an integrated system of uniquely identifiable communicating devices which exchange information in a connected network to provide extensive services. IoT devices have very limited memory, computational power, and power supply. Traditional operating systems (OS) have no way to meet the needs of IoT systems. In this paper, we thus analyze the challenges of IoT OS and survey applicable open source OSs.

Performance evaluation of recommendation algorithms on Internet of Things services

NASA Astrophysics Data System (ADS)

Mashal, Ibrahim; Alsaryrah, Osama; Chung, Tein-Yaw

2016-06-01

Internet of Things (IoT) is the next wave of industry revolution that will initiate many services, such as personal health care and green energy monitoring, which people may subscribe for their convenience. Recommending IoT services to the users based on objects they own will become very crucial for the success of IoT. In this work, we introduce the concept of service recommender systems in IoT by a formal model. As a first attempt in this direction, we have proposed a hyper-graph model for IoT recommender system in which each hyper-edge connects users, objects, and services. Next, we studied the usefulness of traditional recommendation schemes and their hybrid approaches on IoT service recommendation (IoTSRS) based on existing well known metrics. The preliminary results show that existing approaches perform reasonably well but further extension is required for IoTSRS. Several challenges were discussed to point out the direction of future development in IoTSR.

Research and implementation on improving I/O performance of streaming media storage system

NASA Astrophysics Data System (ADS)

Lu, Zheng-wu; Wang, Yu-de; Jiang, Guo-song

2008-12-01

In this paper, we study the special requirements of a special storage system: streaming media server, and propose a solution to improve I/O performance of RAID storage system. The solution is suitable for streaming media applications. A streaming media storage subsystem includes the I/O interfaces, RAID arrays, I/O scheduling and device drivers. The solution is implemented on the top of the storage subsystem I/O Interface. Storage subsystem is the performance bottlenecks of a streaming media system, and I/O interface directly affect the performance of the storage subsystem. According to theoretical analysis, 64 KB block-size is most appropriate for streaming media applications. We carry out experiment in detail, and verified that the proper block-size really is 64KB. It is in accordance with our analysis. The experiment results also show that by using DMA controller, efficient memory management technology and mailbox interface design mechanism, streaming media storage system achieves a high-speed data throughput.

The Integration of DCS I/O to an Existing PLC

NASA Technical Reports Server (NTRS)

Sadhukhan, Debashis; Mihevic, John

2013-01-01

At the NASA Glenn Research Center (GRC), Existing Programmable Logic Controller (PLC) I/O was replaced with Distributed Control System (DCS) I/O, while keeping the existing PLC sequence Logic. The reason for integration of the PLC logic and DCS I/O, along with the evaluation of the resulting system is the subject of this paper. The pros and cons of the old system and new upgrade are described, including operator workstation screen update times. Detail of the physical layout and the communication between the PLC, the DCS I/O and the operator workstations are illustrated. The complex characteristics of a central process control system and the plan to remove the PLC processors in future upgrades is also discussed.

A Selective Group Authentication Scheme for IoT-Based Medical Information System.

PubMed

Park, YoHan; Park, YoungHo

2017-04-01

The technology of IoT combined with medical systems is expected to support advanced medical services. However, unsolved security problems, such as misuse of medical devices, illegal access to the medical server and so on, make IoT-based medical systems not be applied widely. In addition, users have a high burden of computation to access Things for the explosive growth of IoT devices. Because medical information is critical and important, but users have a restricted computing power, IoT-based medical systems are required to provide secure and efficient authentication for users. In this paper, we propose a selective group authentication scheme using Shamir's threshold technique. The property of selectivity gives the right of choice to users to form a group which consists of things users select and access. And users can get an access authority for those Things at a time. Thus, our scheme provides an efficient user authentication for multiple Things and conditional access authority for safe IoT-based medical information system. To the best of our knowledge, our proposed scheme is the first in which selectivity is combined with group authentication in IoT environments.

Asymmetrical features of frequency and intensity in the Io-related Jovian decametric radio sources: Modeling of the Io-Jupiter system

NASA Astrophysics Data System (ADS)

Matsuda, K.; Misawa, H.; Terada, N.; Katoh, Y.

2010-12-01

Part of the Io-related Jovian decametric radiation (Io-DAM) has been thought to be excited in the auroral cavity formed on field lines downstream of Io. Since source regions of Io-DAM called Io-A and Io-B are located in dusk and dawn local times despite having nearly equal magnetic longitudes, some of the observed asymmetries between Io-A and Io-B events are expected to be due to the difference in the local times. We developed a static Vlasov code, applied it to the Io-Jupiter system, and investigated source structure in order to clarify the ways in which the characteristics of Io-DAM are affected by the plasma in the Jovian ionosphere. Generally there are various solutions which satisfy the quasi-neutrality condition for almost identical boundary conditions. With regard to the solutions with two transition layers, if the altitude of a low-altitude transition layer (LATL) is higher, the voltage at the LATL and the ionospheric proton current density is smaller. Similarly, if the altitude of a high-altitude transition layer (HATL) is higher, the voltage at the HATL and the magnetospheric electron current density is larger. A solution with a smaller ionospheric density for Io-B than for Io-A indicates lower altitude of the LATL for Io-B, which is consistent with the observed high-frequency limit higher for Io-B than for Io-A. This suggests that the high-frequency limit is affected by the local time. It is also expected that the difference in ionospheric proton current densities would be associated with the observed asymmetry of emission intensity.

Alcator C-Mod Digital Plasma Control System

NASA Astrophysics Data System (ADS)

Wolfe, S. M.

2005-10-01

A new digital plasma control system (DPCS) has been implemented for Alcator C-Mod. The new system was put into service at the start of the 2005 run campaign and has been in routine operation since. The system consists of two 64-input, 16-output cPCI digitizers attached to a rack-mounted single-CPU Linux server, which performs both the I/O and the computation. During initial operation, the system was set up to directly emulate the original C-Mod ``Hybrid'' MIMO linear control system. Compatibility with the previous control system allows the existing user interface software and data structures to be used with the new hardware. The control program is written in IDL and runs under standard Linux. Interrupts are disabled during the plasma pulses to achieve real-time operation. A synchronous loop is executed with a nominal cycle rate of 10 kHz. Emulation of the original linear control algorithms requires 50 μsec per iteration, with the time evenly split between I/O and computation, so rates of about 20 KHz are achievable. Reliable vertical position control has been demonstrated with cycle rates as low as 5 KHz. Additional computations, including non-linear algorithms and adaptive response, are implemented as optional procedure calls within the main real-time loop.

Strong tidal dissipation in Io and Jupiter from astrometric observations.

PubMed

Lainey, Valéry; Arlot, Jean-Eudes; Karatekin, Ozgür; Van Hoolst, Tim

2009-06-18

Io is the volcanically most active body in the Solar System and has a large surface heat flux. The geological activity is thought to be the result of tides raised by Jupiter, but it is not known whether the current tidal heat production is sufficiently high to generate the observed surface heat flow. Io's tidal heat comes from the orbital energy of the Io-Jupiter system (resulting in orbital acceleration), whereas dissipation of energy in Jupiter causes Io's orbital motion to decelerate. Here we report a determination of the tidal dissipation in Io and Jupiter through its effect on the orbital motions of the Galilean moons. Our results show that the rate of internal energy dissipation in Io (k(2)/Q = 0.015 +/- 0.003, where k(2) is the Love number and Q is the quality factor) is in good agreement with the observed surface heat flow, and suggest that Io is close to thermal equilibrium. Dissipation in Jupiter (k(2)/Q = (1.102 +/- 0.203) x 10(-5)) is close to the upper bound of its average value expected from the long-term evolution of the system, and dissipation in extrasolar planets may be higher than presently assumed. The measured secular accelerations indicate that Io is evolving inwards, towards Jupiter, and that the three innermost Galilean moons (Io, Europa and Ganymede) are evolving out of the exact Laplace resonance.

Understanding I/O workload characteristics of a Peta-scale storage system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Youngjae; Gunasekaran, Raghul

2015-01-01

Understanding workload characteristics is critical for optimizing and improving the performance of current systems and software, and architecting new storage systems based on observed workload patterns. In this paper, we characterize the I/O workloads of scientific applications of one of the world s fastest high performance computing (HPC) storage cluster, Spider, at the Oak Ridge Leadership Computing Facility (OLCF). OLCF flagship petascale simulation platform, Titan, and other large HPC clusters, in total over 250 thousands compute cores, depend on Spider for their I/O needs. We characterize the system utilization, the demands of reads and writes, idle time, storage space utilization,more » and the distribution of read requests to write requests for the Peta-scale Storage Systems. From this study, we develop synthesized workloads, and we show that the read and write I/O bandwidth usage as well as the inter-arrival time of requests can be modeled as a Pareto distribution. We also study the I/O load imbalance problems using I/O performance data collected from the Spider storage system.« less

Taming parallel I/O complexity with auto-tuning

DOE PAGES

Behzad, Babak; Luu, Huong Vu Thanh; Huchette, Joseph; ...

2013-11-17

We present an auto-tuning system for optimizing I/O performance of HDF5 applications and demonstrate its value across platforms, applications, and at scale. The system uses a genetic algorithm to search a large space of tunable parameters and to identify effective settings at all layers of the parallel I/O stack. The parameter settings are applied transparently by the auto-tuning system via dynamically intercepted HDF5 calls. To validate our auto-tuning system, we applied it to three I/O benchmarks (VPIC, VORPAL, and GCRM) that replicate the I/O activity of their respective applications. We tested the system with different weak-scaling configurations (128, 2048, andmore » 4096 CPU cores) that generate 30 GB to 1 TB of data, and executed these configurations on diverse HPC platforms (Cray XE6, IBM BG/P, and Dell Cluster). In all cases, the auto-tuning framework identified tunable parameters that substantially improved write performance over default system settings. In conclusion, we consistently demonstrate I/O write speedups between 2x and 100x for test configurations.« less

An IoT-Based Solution for Monitoring a Fleet of Educational Buildings Focusing on Energy Efficiency

PubMed Central

Akrivopoulos, Orestis

2017-01-01

Raising awareness among young people and changing their behaviour and habits concerning energy usage is key to achieving sustained energy saving. Additionally, young people are very sensitive to environmental protection so raising awareness among children is much easier than with any other group of citizens. This work examines ways to create an innovative Information & Communication Technologies (ICT) ecosystem (including web-based, mobile, social and sensing elements) tailored specifically for school environments, taking into account both the users (faculty, staff, students, parents) and school buildings, thus motivating and supporting young citizens’ behavioural change to achieve greater energy efficiency. A mixture of open-source IoT hardware and proprietary platforms on the infrastructure level, are currently being utilized for monitoring a fleet of 18 educational buildings across 3 countries, comprising over 700 IoT monitoring points. Hereon presented is the system’s high-level architecture, as well as several aspects of its implementation, related to the application domain of educational building monitoring and energy efficiency. The system is developed based on open-source technologies and services in order to make it capable of providing open IT-infrastructure and support from different commercial hardware/sensor vendors as well as open-source solutions. The system presented can be used to develop and offer new app-based solutions that can be used either for educational purposes or for managing the energy efficiency of the building. The system is replicable and adaptable to settings that may be different than the scenarios envisioned here (e.g., targeting different climate zones), different IT infrastructures and can be easily extended to accommodate integration with other systems. The overall performance of the system is evaluated in real-world environment in terms of scalability, responsiveness and simplicity. PMID:28994719

Performance analysis of routing protocols for IoT

NASA Astrophysics Data System (ADS)

Manda, Sridhar; Nalini, N.

2018-04-01

Internet of Things (IoT) is an arrangement of advancements that are between disciplinary. It is utilized to have compelling combination of both physical and computerized things. With IoT physical things can have personal virtual identities and participate in distributed computing. Realization of IoT needs the usage of sensors based on the sector for which IoT is integrated. For instance, in healthcare domain, IoT needs to have integration with wearable sensors used by patients. As sensor devices produce huge amount of data, often called big data, there should be efficient routing protocols in place. To the extent remote systems is worried there are some current protocols, for example, OLSR, DSR and AODV. It additionally tosses light into Trust based routing protocol for low-power and lossy systems (TRPL) for IoT. These are broadly utilized remote directing protocols. As IoT is developing round the corner, it is basic to investigate routing protocols that and evaluate their execution regarding throughput, end to end delay, and directing overhead. The execution experiences can help in settling on very much educated choices while incorporating remote systems with IoT. In this paper, we analyzed different routing protocols and their performance is compared. It is found that AODV showed better performance than other routing protocols aforementioned.

Rethinking key–value store for parallel I/O optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kougkas, Anthony; Eslami, Hassan; Sun, Xian-He

2015-01-26

Key-value stores are being widely used as the storage system for large-scale internet services and cloud storage systems. However, they are rarely used in HPC systems, where parallel file systems are the dominant storage solution. In this study, we examine the architecture differences and performance characteristics of parallel file systems and key-value stores. We propose using key-value stores to optimize overall Input/Output (I/O) performance, especially for workloads that parallel file systems cannot handle well, such as the cases with intense data synchronization or heavy metadata operations. We conducted experiments with several synthetic benchmarks, an I/O benchmark, and a real application.more » We modeled the performance of these two systems using collected data from our experiments, and we provide a predictive method to identify which system offers better I/O performance given a specific workload. The results show that we can optimize the I/O performance in HPC systems by utilizing key-value stores.« less

''Towards a High-Performance and Robust Implementation of MPI-IO on Top of GPFS''

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prost, J.P.; Tremann, R.; Blackwore, R.

2000-01-11

MPI-IO/GPFS is a prototype implementation of the I/O chapter of the Message Passing Interface (MPI) 2 standard. It uses the IBM General Parallel File System (GPFS), with prototyped extensions, as the underlying file system. this paper describes the features of this prototype which support its high performance and robustness. The use of hints at the file system level and at the MPI-IO level allows tailoring the use of the file system to the application needs. Error handling in collective operations provides robust error reporting and deadlock prevention in case of returning errors.

Identification and Characterization of a Novel Issatchenkia orientalis GPI-Anchored Protein, IoGas1, Required for Resistance to Low pH and Salt Stress

PubMed Central

Matsushika, Akinori; Negi, Kanako; Suzuki, Toshihiro; Goshima, Tetsuya; Hoshino, Tamotsu

2016-01-01

The use of yeasts tolerant to acid (low pH) and salt stress is of industrial importance for several bioproduction processes. To identify new candidate genes having potential roles in low-pH tolerance, we screened an expression genomic DNA library of a multiple-stress-tolerant yeast, Issatchenkia orientalis (Pichia kudriavzevii), for clones that allowed Saccharomyces cerevisiae cells to grow under highly acidic conditions (pH 2.0). A genomic DNA clone containing two putative open reading frames was obtained, of which the putative protein-coding gene comprising 1629 bp was retransformed into the host. This transformant grew significantly at pH 2.0, and at pH 2.5 in the presence of 7.5% Na2SO4. The predicted amino acid sequence of this new gene, named I. orientalis GAS1 (IoGAS1), was 60% identical to the S. cerevisiae Gas1 protein, a glycosylphosphatidylinositol-anchored protein essential for maintaining cell wall integrity, and 58–59% identical to Candida albicans Phr1 and Phr2, pH-responsive proteins implicated in cell wall assembly and virulence. Northern hybridization analyses indicated that, as for the C. albicans homologs, IoGAS1 expression was pH-dependent, with expression increasing with decreasing pH (from 4.0 to 2.0) of the medium. These results suggest that IoGAS1 represents a novel pH-regulated system required for the adaptation of I. orientalis to environments of diverse pH. Heterologous expression of IoGAS1 complemented the growth and morphological defects of a S. cerevisiae gas1Δ mutant, demonstrating that IoGAS1 and the corresponding S. cerevisiae gene play similar roles in cell wall biosynthesis. Site-directed mutagenesis experiments revealed that two conserved glutamate residues (E161 and E262) in the IoGas1 protein play a crucial role in yeast morphogenesis and tolerance to low pH and salt stress. Furthermore, overexpression of IoGAS1 in S. cerevisiae remarkably improved the ethanol fermentation ability at pH 2.5, and at pH 2.0 in the presence of salt (5% Na2SO4), compared to that of a reference strain. Our results strongly suggest that constitutive expression of the IoGAS1 gene in S. cerevisiae could be advantageous for several fermentation processes under these stress conditions. PMID:27589271

Collective input/output under memory constraints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Yin; Chen, Yong; Zhuang, Yu

2014-12-18

Compared with current high-performance computing (HPC) systems, exascale systems are expected to have much less memory per node, which can significantly reduce necessary collective input/output (I/O) performance. In this study, we introduce a memory-conscious collective I/O strategy that takes into account memory capacity and bandwidth constraints. The new strategy restricts aggregation data traffic within disjointed subgroups, coordinates I/O accesses in intranode and internode layers, and determines I/O aggregators at run time considering memory consumption among processes. We have prototyped the design and evaluated it with commonly used benchmarks to verify its potential. The evaluation results demonstrate that this strategy holdsmore » promise in mitigating the memory pressure, alleviating the contention for memory bandwidth, and improving the I/O performance for projected extreme-scale systems. Given the importance of supporting increasingly data-intensive workloads and projected memory constraints on increasingly larger scale HPC systems, this new memory-conscious collective I/O can have a significant positive impact on scientific discovery productivity.« less

Optimization of energy window and evaluation of scatter compensation methods in MPS using the ideal observer with model mismatch

NASA Astrophysics Data System (ADS)

Ghaly, Michael; Links, Jonathan M.; Frey, Eric

2015-03-01

In this work, we used the ideal observer (IO) and IO with model mismatch (IO-MM) applied in the projection domain and an anthropomorphic Channelized Hotelling Observer (CHO) applied to reconstructed images to optimize the acquisition energy window width and evaluate various scatter compensation methods in the context of a myocardial perfusion SPECT defect detection task. The IO has perfect knowledge of the image formation process and thus reflects performance with perfect compensation for image-degrading factors. Thus, using the IO to optimize imaging systems could lead to suboptimal parameters compared to those optimized for humans interpreting SPECT images reconstructed with imperfect or no compensation. The IO-MM allows incorporating imperfect system models into the IO optimization process. We found that with near-perfect scatter compensation, the optimal energy window for the IO and CHO were similar; in its absence the IO-MM gave a better prediction of the optimal energy window for the CHO using different scatter compensation methods. These data suggest that the IO-MM may be useful for projection-domain optimization when model mismatch is significant, and that the IO is useful when followed by reconstruction with good models of the image formation process.

Pruning-Based, Energy-Optimal, Deterministic I/O Device Scheduling for Hard Real-Time Systems

DTIC Science & Technology

2005-02-01

However, DPM via I/O device scheduling for hard real - time systems has received relatively little attention. In this paper,we present an offline I/O...polynomial time. We present experimental results to show that EDS and MDO reduce the energy consumption of I/O devices significantly for hard real - time systems .

RapidIO as a multi-purpose interconnect

NASA Astrophysics Data System (ADS)

Baymani, Simaolhoda; Alexopoulos, Konstantinos; Valat, Sébastien

2017-10-01

RapidIO (http://rapidio.org/) technology is a packet-switched high-performance fabric, which has been under active development since 1997. Originally meant to be a front side bus, it developed into a system level interconnect which is today used in all 4G/LTE base stations world wide. RapidIO is often used in embedded systems that require high reliability, low latency and scalability in a heterogeneous environment - features that are highly interesting for several use cases, such as data analytics and data acquisition (DAQ) networks. We will present the results of evaluating RapidIO in a data analytics environment, from setup to benchmark. Specifically, we will share the experience of running ROOT and Hadoop on top of RapidIO. To demonstrate the multi-purpose characteristics of RapidIO, we will also present the results of investigating RapidIO as a technology for high-speed DAQ networks using a generic multi-protocol event-building emulation tool. In addition we will present lessons learned from implementing native ports of CERN applications to RapidIO.

Panel summary of cyber-physical systems (CPS) and Internet of Things (IoT) opportunities with information fusion

NASA Astrophysics Data System (ADS)

Blasch, Erik; Kadar, Ivan; Grewe, Lynne L.; Brooks, Richard; Yu, Wei; Kwasinski, Andres; Thomopoulos, Stelios; Salerno, John; Qi, Hairong

2017-05-01

During the 2016 SPIE DSS conference, nine panelists were invited to highlight the trends and opportunities in cyber-physical systems (CPS) and Internet of Things (IoT) with information fusion. The world will be ubiquitously outfitted with many sensors to support our daily living thorough the Internet of Things (IoT), manage infrastructure developments with cyber-physical systems (CPS), as well as provide communication through networked information fusion technology over the internet (NIFTI). This paper summarizes the panel discussions on opportunities of information fusion to the growing trends in CPS and IoT. The summary includes the concepts and areas where information supports these CPS/IoT which includes situation awareness, transportation, and smart grids.

Global shape estimates and GIS cartography of Io and Enceladus using new control point network

NASA Astrophysics Data System (ADS)

Nadezhdina, I.; Patraty, V.; Shishkina, L.; Zhukov, D.; Zubarev, A.; Karachevtseva, I.; Oberst, J.

2012-04-01

We have analyzed a total of 53 Galileo and Voyager images of Io and 54 Cassini images of Enceladus to derive new geodetic control point networks for the two satellites. In order to derive the network for Io we used a subset of 66 images from those used in previous control point network studies [1, 2]. Additionally we have carried out new point measurements. We used recently reconstructed Galileo spacecraft trajectory data, supplied by the spacecraft navigation team of JPL. A total of 1956 tie point measurements for Io and 4392 ones for Enceladus have been carried out, which were processed by performing photogrammetric bundle block adjustments. Measurements and block adjustments were performed by means of the «PHOTOMOD» software [3] which was especially adapted for this study to accommodate global networks of small bodies, such as Io and Enceladus. As a result, two catalogs with the Cartesian three-dimensional coordinates of 197 and 351 control points were obtained for Io and Enceladus, respectively. The control points for Io have a mean overall accuracy of 4985.7 m (RMS). The individual accuracy of the control points for Enceladus differ substantially over the surface (the range is from 0.1 to 36.0 km) because images lack coverage and resolutions. We also determine best-fit spheres, spheroids, and tri-axial ellipsoids. The centers of the models were found to be shifted from the coordinate system origin attesting to possible errors in the ephemeris of Io. Conclusion and Future work: A comparison of our results for Io with the most recent control point network analysis [2] has revealed that we managed to derive the same accuracy of the control points using a smaller number of images and measurements (This study: 1956 measurements, DLR study: 4392). This probably attests to the fact that the now available new navigation data are internally more consistent. At present an analysis of the data is in progress. We report that control point measurements and global network analysis for small planetary bodies by means of the software «PHOTOMOD» is fast and efficient. Using the new control points and shape models of the satellites we are currently preparing new maps of Io and Enceladus using GIS tools. For parts of the surface for which we have quality stereo-images we will produce DEMs and orthoimages, which will be shown at the conference. Acknowledgments: This research was funded by the Ministry of Education and Science of the Russian Federation (MEGA-GRANT, Project name: "Geodesy, cartography and the study of planets and satellites", contract No. 11.G34.31.0021).

I/O-aware bandwidth allocation for petascale computing systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Zhou; Yang, Xu; Zhao, Dongfang

In the Big Data era, the gap between the storage performance and an appli- cation's I/O requirement is increasing. I/O congestion caused by concurrent storage accesses from multiple applications is inevitable and severely harms the performance. Conventional approaches either focus on optimizing an ap- plication's access pattern individually or handle I/O requests on a low-level storage layer without any knowledge from the upper-level applications. In this paper, we present a novel I/O-aware bandwidth allocation framework to coordinate ongoing I/O requests on petascale computing systems. The motivation behind this innovation is that the resource management system has a holistic view ofmore » both the system state and jobs' activities and can dy- namically control the jobs' status or allocate resource on the y during their execution. We treat a job's I/O requests as periodical subjobs within its lifecycle and transform the I/O congestion issue into a classical scheduling problem. Based on this model, we propose a bandwidth management mech- anism as an extension to the existing scheduling system. We design several bandwidth allocation policies with different optimization objectives either on user-oriented metrics or system performance. We conduct extensive trace- based simulations using real job traces and I/O traces from a production IBM Blue Gene/Q system at Argonne National Laboratory. Experimental results demonstrate that our new design can improve job performance by more than 30%, as well as increasing system performance.« less

A General Provincial Situation Visualization System Based on iPhone Operating System of Shandong Province

NASA Astrophysics Data System (ADS)

Ye, Z.; Xiang, H.

2014-04-01

The paper discusses the basic principles and the problem solutions during the design and implementation of the mobile GIS system, and base on the research result, we developed the General Provincial Situation Visualization System Based on iOS of Shandong Province. The system is developed in the Objective-C programming language, and use the ArcGIS Runtime SDK for IOS as the development tool to call the "World-map Shandong" services to implement the development of the General Provincial Situation Visualization System Based on iOS devices. The system is currently available for download in the Appstore and is chosen as the typical application case of ESRI China ArcGIS API for iOS.

A federated capability-based access control mechanism for internet of things (IoTs)

NASA Astrophysics Data System (ADS)

Xu, Ronghua; Chen, Yu; Blasch, Erik; Chen, Genshe

2018-05-01

The prevalence of Internet of Things (IoTs) allows heterogeneous embedded smart devices to collaboratively provide intelligent services with or without human intervention. While leveraging the large-scale IoT-based applications like Smart Gird and Smart Cities, IoT also incurs more concerns on privacy and security. Among the top security challenges that IoTs face is that access authorization is critical in resource and information protection over IoTs. Traditional access control approaches, like Access Control Lists (ACL), Role-based Access Control (RBAC) and Attribute-based Access Control (ABAC), are not able to provide a scalable, manageable and efficient mechanisms to meet requirement of IoT systems. The extraordinary large number of nodes, heterogeneity as well as dynamicity, necessitate more fine-grained, lightweight mechanisms for IoT devices. In this paper, a federated capability-based access control (FedCAC) framework is proposed to enable an effective access control processes to devices, services and information in large scale IoT systems. The federated capability delegation mechanism, based on a propagation tree, is illustrated for access permission propagation. An identity-based capability token management strategy is presented, which involves registering, propagation and revocation of the access authorization. Through delegating centralized authorization decision-making policy to local domain delegator, the access authorization process is locally conducted on the service provider that integrates situational awareness (SAW) and customized contextual conditions. Implemented and tested on both resources-constrained devices, like smart sensors and Raspberry PI, and non-resource-constrained devices, like laptops and smart phones, our experimental results demonstrate the feasibility of the proposed FedCAC approach to offer a scalable, lightweight and fine-grained access control solution to IoT systems connected to a system network.

Comparison of lateral abdominal muscle thickness between weightlifters and matched controls.

PubMed

Sitilertpisan, Patraporn; Pirunsan, Ubon; Puangmali, Aatit; Ratanapinunchai, Jonjin; Kiatwattanacharoen, Suchart; Neamin, Hudsaleark; Laskin, James J

2011-11-01

To compare lateral abdominal muscle thickness between weightlifters and matched controls. A case control study design. University laboratory. 16 female Thai national weightlifters and 16 matched controls participated in this study. Ultrasound imaging with a 12-MHz linear array was used to measure the resting thickness of transversus abdominis (TrA), internal oblique (IO) and total thickness (Total) of lateral abdominal muscle (LAM) on the right side of abdominal wall. The absolute muscle thickness and the relative contribution of each muscle to the total thickness were determined. Weightlifters had significantly thicker absolute TrA and IO muscles than matched controls (p < 0.01). Further, the relative thickness of the IO was significantly greater in weightlifters than matched controls (p < 0.05). The findings of this study suggest that routine Olympic style weight training among female weightlifters appears to result in preferential hypertrophy or adaptation of the IO muscle. Copyright © 2011 Elsevier Ltd. All rights reserved.

Advanced Information Processing System (AIPS) proof-of-concept system functional design I/O network system services

NASA Technical Reports Server (NTRS)

1985-01-01

The function design of the Input/Output (I/O) services for the Advanced Information Processing System (AIPS) proof of concept system is described. The data flow diagrams, which show the functional processes in I/O services and the data that flows among them, are contained. A complete list of the data identified on the data flow diagrams and in the process descriptions are provided.

Fast convergence of learning requires plasticity between inferior olive and deep cerebellar nuclei in a manipulation task: a closed-loop robotic simulation

PubMed Central

Luque, Niceto R.; Garrido, Jesús A.; Carrillo, Richard R.; D'Angelo, Egidio; Ros, Eduardo

2014-01-01

The cerebellum is known to play a critical role in learning relevant patterns of activity for adaptive motor control, but the underlying network mechanisms are only partly understood. The classical long-term synaptic plasticity between parallel fibers (PFs) and Purkinje cells (PCs), which is driven by the inferior olive (IO), can only account for limited aspects of learning. Recently, the role of additional forms of plasticity in the granular layer, molecular layer and deep cerebellar nuclei (DCN) has been considered. In particular, learning at DCN synapses allows for generalization, but convergence to a stable state requires hundreds of repetitions. In this paper we have explored the putative role of the IO-DCN connection by endowing it with adaptable weights and exploring its implications in a closed-loop robotic manipulation task. Our results show that IO-DCN plasticity accelerates convergence of learning by up to two orders of magnitude without conflicting with the generalization properties conferred by DCN plasticity. Thus, this model suggests that multiple distributed learning mechanisms provide a key for explaining the complex properties of procedural learning and open up new experimental questions for synaptic plasticity in the cerebellar network. PMID:25177290

Advanced information processing system: Input/output system services

NASA Technical Reports Server (NTRS)

Masotto, Tom; Alger, Linda

1989-01-01

The functional requirements and detailed specifications for the Input/Output (I/O) Systems Services of the Advanced Information Processing System (AIPS) are discussed. The introductory section is provided to outline the overall architecture and functional requirements of the AIPS system. Section 1.1 gives a brief overview of the AIPS architecture as well as a detailed description of the AIPS fault tolerant network architecture, while section 1.2 provides an introduction to the AIPS systems software. Sections 2 and 3 describe the functional requirements and design and detailed specifications of the I/O User Interface and Communications Management modules of the I/O System Services, respectively. Section 4 illustrates the use of the I/O System Services, while Section 5 concludes with a summary of results and suggestions for future work in this area.

A Middleware with Comprehensive Quality of Context Support for the Internet of Things Applications

PubMed Central

Gomes, Berto de Tácio Pereira; Muniz, Luiz Carlos Melo; dos Santos, Davi Viana; Lopes, Rafael Fernandes; Coutinho, Luciano Reis; Carvalho, Felipe Oliveira; Endler, Markus

2017-01-01

Context aware systems are able to adapt their behavior according to the environment in which the user is. They can be integrated into an Internet of Things (IoT) infrastructure, allowing a better perception of the user’s physical environment by collecting context data from sensors embedded in devices known as smart objects. An IoT extension called the Internet of Mobile Things (IoMT) suggests new scenarios in which smart objects and IoT gateways can move autonomously or be moved easily. In a comprehensive view, Quality of Context (QoC) is a term that can express quality requirements of context aware applications. These requirements can be those related to the quality of information provided by the sensors (e.g., accuracy, resolution, age, validity time) or those referring to the quality of the data distribution service (e.g, reliability, delay, delivery time). Some functionalities of context aware applications and/or decision-making processes of these applications and their users depend on the level of quality of context available, which tend to vary over time for various reasons. Reviewing the literature, it is possible to verify that the quality of context support provided by IoT-oriented middleware systems still has limitations in relation to at least four relevant aspects: (i) quality of context provisioning; (ii) quality of context monitoring; (iii) support for heterogeneous device and technology management; (iv) support for reliable data delivery in mobility scenarios. This paper presents two main contributions: (i) a state-of-the-art survey specifically aimed at analyzing the middleware with quality of context support and; (ii) a new middleware with comprehensive quality of context support for Internet of Things Applications. The proposed middleware was evaluated and the results are presented and discussed in this article, which also shows a case study involving the development of a mobile remote patient monitoring application that was developed using the proposed middleware. This case study highlights how middleware components were used to meet the quality of context requirements of the application. In addition, the proposed middleware was compared to other solutions in the literature. PMID:29292791

A Middleware with Comprehensive Quality of Context Support for the Internet of Things Applications.

PubMed

Gomes, Berto de Tácio Pereira; Muniz, Luiz Carlos Melo; da Silva E Silva, Francisco José; Dos Santos, Davi Viana; Lopes, Rafael Fernandes; Coutinho, Luciano Reis; Carvalho, Felipe Oliveira; Endler, Markus

2017-12-08

Context aware systems are able to adapt their behavior according to the environment in which the user is. They can be integrated into an Internet of Things (IoT) infrastructure, allowing a better perception of the user's physical environment by collecting context data from sensors embedded in devices known as smart objects. An IoT extension called the Internet of Mobile Things (IoMT) suggests new scenarios in which smart objects and IoT gateways can move autonomously or be moved easily. In a comprehensive view, Quality of Context (QoC) is a term that can express quality requirements of context aware applications. These requirements can be those related to the quality of information provided by the sensors (e.g., accuracy, resolution, age, validity time) or those referring to the quality of the data distribution service (e.g, reliability, delay, delivery time). Some functionalities of context aware applications and/or decision-making processes of these applications and their users depend on the level of quality of context available, which tend to vary over time for various reasons. Reviewing the literature, it is possible to verify that the quality of context support provided by IoT-oriented middleware systems still has limitations in relation to at least four relevant aspects: (i) quality of context provisioning; (ii) quality of context monitoring; (iii) support for heterogeneous device and technology management; (iv) support for reliable data delivery in mobility scenarios. This paper presents two main contributions: (i) a state-of-the-art survey specifically aimed at analyzing the middleware with quality of context support and; (ii) a new middleware with comprehensive quality of context support for Internet of Things Applications. The proposed middleware was evaluated and the results are presented and discussed in this article, which also shows a case study involving the development of a mobile remote patient monitoring application that was developed using the proposed middleware. This case study highlights how middleware components were used to meet the quality of context requirements of the application. In addition, the proposed middleware was compared to other solutions in the literature.

Dust escape from Io

NASA Astrophysics Data System (ADS)

Flandes, Alberto

2004-08-01

The Dust ballerina skirt is a set of well defined streams composed of nanometric sized dust particles that escape from the Jovian system and may be accelerated up to >=200 km/s. The source of this dust is Jupiter's moon Io, the most volcanically active body in the Solar system. The escape of dust grains from Jupiter requires first the escape of these grains from Io. This work is basically devoted to explain this escape given that the driving of dust particles to great heights and later injection into the ionosphere of Io may give the particles an equilibrium potential that allow the magnetic field to accelerate them away from Io. The grain sizes obtained through this study match very well to the values required for the particles to escape from the Jovian system.

Resolving Io's Volcanoes from a Mutual Event Observation at the Large Binocular Telescope

NASA Astrophysics Data System (ADS)

de Kleer, K.; Skrutskie, M.; Leisenring, J.; Davies, A. G.; Resnick, A.; Conrad, A.; De Pater, I.; Hinz, P.; Defrere, D.; Veillet, C.

2016-12-01

Near-infrared observations of Io during occultation by Jupiter and the other Galilean satellites have been central to ground-based studies of Io's volcanism for decades. When such observations are made using adaptive optics on 8-10m telescopes, the infrared emission from individual features can be resolved at a resolution approaching a few km on Io's surface. On March 8, 2015, the Large Binocular Telescope Interferometer (LBTI) observed Io during a Europa mutual occultation event. Images were obtained at a wavelength of 4.8 microns every 123 milliseconds, corresponding to 2 km on Io's surface. The thermal emission from four hot spots including Loki Patera, Pillan Patera, and Kurdalagon Patera is clearly resolved. The latter two hot spots hosted bright eruptions in early 2015; the thermal emission from these sites likely represents the aftermath of those eruptions. The occultation light curves are used to construct a brightness temperature map for each of the four hot spots, from which the lava age is estimated using a model for cooling basaltic lavas. The thermal mapping of Loki Patera has produced the first-ever temperature map of the entire patera floor at high (10 km) spatial resolution, and the corresponding age distribution yields the resurfacing rate. For each hot spot, the age and spatial extent of the lava is interpreted in the context of its activity during the surrounding months.

Crowding, visual awareness, and their respective neural loci

PubMed Central

Shin, Kilho; Chung, Susana T. L.; Tjan, Bosco S.

2017-01-01

In peripheral vision, object identification can be impeded when a target object is flanked by other objects. This phenomenon of crowding has been attributed to basic processes associated with image encoding by the visual system, but the neural origin of crowding is not known. Determining whether crowding depends on subjective awareness of the flankers can provide information on the neural origin of crowding. However, recent studies that manipulated flanker awareness have yielded conflicting results. In the current study, we suppressed flanker awareness with two methods: interocular suppression (IOS) and adaptation-induced blindness (AIB). We tested two different types of stimuli: gratings and letters. With IOS, we found that the magnitude of crowding increased as the number of physical flankers increased, even when the observers did not report seeing any of the flankers. In contrast, when flanker awareness was manipulated with AIB, the magnitude of crowding increased with the number of perceived flankers. Our results show that whether crowding is contingent on awareness of the flankers depends on the method used to suppress awareness. In addition, our results imply that the locus of crowding is upstream from the neural locus of IOS and close to or downstream from that of AIB. Neurophysiology and neuroimaging studies jointly implicate mid-to-high level visual processing stages for IOS, while direct evidence regarding the neural locus of AIB is limited. The most consistent interpretation of our empirical findings is to place the neural locus of crowding at an early cortical site, such as V1 or V2. PMID:28549353

Profiling and Improving I/O Performance of a Large-Scale Climate Scientific Application

NASA Technical Reports Server (NTRS)

Liu, Zhuo; Wang, Bin; Wang, Teng; Tian, Yuan; Xu, Cong; Wang, Yandong; Yu, Weikuan; Cruz, Carlos A.; Zhou, Shujia; Clune, Tom;

Reconfigurable signal processor designs for advanced digital array radar systems

NASA Astrophysics Data System (ADS)

Suarez, Hernan; Zhang, Yan (Rockee); Yu, Xining

2017-05-01

The new challenges originated from Digital Array Radar (DAR) demands a new generation of reconfigurable backend processor in the system. The new FPGA devices can support much higher speed, more bandwidth and processing capabilities for the need of digital Line Replaceable Unit (LRU). This study focuses on using the latest Altera and Xilinx devices in an adaptive beamforming processor. The field reprogrammable RF devices from Analog Devices are used as analog front end transceivers. Different from other existing Software-Defined Radio transceivers on the market, this processor is designed for distributed adaptive beamforming in a networked environment. The following aspects of the novel radar processor will be presented: (1) A new system-on-chip architecture based on Altera's devices and adaptive processing module, especially for the adaptive beamforming and pulse compression, will be introduced, (2) Successful implementation of generation 2 serial RapidIO data links on FPGA, which supports VITA-49 radio packet format for large distributed DAR processing. (3) Demonstration of the feasibility and capabilities of the processor in a Micro-TCA based, SRIO switching backplane to support multichannel beamforming in real-time. (4) Application of this processor in ongoing radar system development projects, including OU's dual-polarized digital array radar, the planned new cylindrical array radars, and future airborne radars.

Sensor-Based Optimization Model for Air Quality Improvement in Home IoT

PubMed Central

Kim, Jonghyuk

2018-01-01

We introduce current home Internet of Things (IoT) technology and present research on its various forms and applications in real life. In addition, we describe IoT marketing strategies as well as specific modeling techniques for improving air quality, a key home IoT service. To this end, we summarize the latest research on sensor-based home IoT, studies on indoor air quality, and technical studies on random data generation. In addition, we develop an air quality improvement model that can be readily applied to the market by acquiring initial analytical data and building infrastructures using spectrum/density analysis and the natural cubic spline method. Accordingly, we generate related data based on user behavioral values. We integrate the logic into the existing home IoT system to enable users to easily access the system through the Web or mobile applications. We expect that the present introduction of a practical marketing application method will contribute to enhancing the expansion of the home IoT market. PMID:29570684

Sensor-Based Optimization Model for Air Quality Improvement in Home IoT.

PubMed

Kim, Jonghyuk; Hwangbo, Hyunwoo

2018-03-23

We introduce current home Internet of Things (IoT) technology and present research on its various forms and applications in real life. In addition, we describe IoT marketing strategies as well as specific modeling techniques for improving air quality, a key home IoT service. To this end, we summarize the latest research on sensor-based home IoT, studies on indoor air quality, and technical studies on random data generation. In addition, we develop an air quality improvement model that can be readily applied to the market by acquiring initial analytical data and building infrastructures using spectrum/density analysis and the natural cubic spline method. Accordingly, we generate related data based on user behavioral values. We integrate the logic into the existing home IoT system to enable users to easily access the system through the Web or mobile applications. We expect that the present introduction of a practical marketing application method will contribute to enhancing the expansion of the home IoT market.

Towards Scalable Deep Learning via I/O Analysis and Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pumma, Sarunya; Si, Min; Feng, Wu-Chun

Deep learning systems have been growing in prominence as a way to automatically characterize objects, trends, and anomalies. Given the importance of deep learning systems, researchers have been investigating techniques to optimize such systems. An area of particular interest has been using large supercomputing systems to quickly generate effective deep learning networks: a phase often referred to as “training” of the deep learning neural network. As we scale existing deep learning frameworks—such as Caffe—on these large supercomputing systems, we notice that the parallelism can help improve the computation tremendously, leaving data I/O as the major bottleneck limiting the overall systemmore » scalability. In this paper, we first present a detailed analysis of the performance bottlenecks of Caffe on large supercomputing systems. Our analysis shows that the I/O subsystem of Caffe—LMDB—relies on memory-mapped I/O to access its database, which can be highly inefficient on large-scale systems because of its interaction with the process scheduling system and the network-based parallel filesystem. Based on this analysis, we then present LMDBIO, our optimized I/O plugin for Caffe that takes into account the data access pattern of Caffe in order to vastly improve I/O performance. Our experimental results show that LMDBIO can improve the overall execution time of Caffe by nearly 20-fold in some cases.« less

Connecting Io's volcanic activity to the Io plasma torus: comparison of Galileo/NIMS volcanic and ground-based torus observations

NASA Astrophysics Data System (ADS)

Magalhaes, F. P.; Lopes, R. M. C.; Rathbun, J. A.; Gonzalez, W. D.; Morgenthaler, J. P.; Echer, E.; Echer, M. P. D. S.

2015-12-01

Io, the innermost of the Jupiter's four Galilean moons, is a remarkable object in the Solar System, due to its intense and energetic volcanic activity. The volcanic sulfur and oxygen in Io's tenuous atmosphere escapes forming an extended neutral cloud around Io and Jupiter. Subsequently, by ionization and pickup ions, a ring of charged particles encircling Jupiter is created, forming the Io plasma torus. Considering this scenario, it is reasonable to expect that the Io plasma torus should be affected by changes in Io's volcanism. Interactions between Io and the Jovian environment is unique and yet not very well understood. Here we present two sets of observations. One from the Galileo Near-Infrared Imaging Spectrograph (NIMS) instrument, which obtained spectral image cubes between 0.7 and 5.2 microns. The other dataset is from ground-based observations of the [SII] 6731 Å emission lines from the Io plasma torus, obtained at McMath-Pierce Solar Telescope, at Kitt Peak. Our dataset from the [SII] 6731 Å emission lines cover more years than the one from the NIMS data. The years presented in this work for a comparative study are from 1998 through 2001. Using the NIMS instrument we were able to identify which volcanoes were active and measure their level of activity. From the [SII] 6731 Å emission lines we were able to trace the densest part of the torus and also the brightness of both ansa. By comparing the results from the Galileo instrument and the ground-based observations, we are exploring how the Io plasma torus responds to large eruptions from Io. We aim with this study to help improve our understanding of this complex coupled system, Jupiter-Io.

On the energy footprint of I/O management in Exascale HPC systems

DOE PAGES

Dorier, Matthieu; Yildiz, Orcun; Ibrahim, Shadi; ...

2016-03-21

The advent of unprecedentedly scalable yet energy hungry Exascale supercomputers poses a major challenge in sustaining a high performance-per-watt ratio. With I/O management acquiring a crucial role in supporting scientific simulations, various I/O management approaches have been proposed to achieve high performance and scalability. But, the details of how these approaches affect energy consumption have not been studied yet. Therefore, this paper aims to explore how much energy a supercomputer consumes while running scientific simulations when adopting various I/O management approaches. In particular, we closely examine three radically different I/O schemes including time partitioning, dedicated cores, and dedicated nodes. Tomore » accomplish this, we implement the three approaches within the Damaris I/O middleware and perform extensive experiments with one of the target HPC applications of the Blue Waters sustained-petaflop supercomputer project: the CM1 atmospheric model. Our experimental results obtained on the French Grid'5000 platform highlight the differences among these three approaches and illustrate in which way various configurations of the application and of the system can impact performance and energy consumption. Moreover, we propose and validate a mathematical model that estimates the energy consumption of a HPC simulation under different I/O approaches. This proposed model gives hints to pre-select the most energy-efficient I/O approach for a particular simulation on a particular HPC system and therefore provides a step towards energy-efficient HPC simulations in Exascale systems. To the best of our knowledge, our work provides the first in-depth look into the energy-performance tradeoffs of I/O management approaches.« less

An MPA-IO interface to HPSS

NASA Technical Reports Server (NTRS)

Jones, Terry; Mark, Richard; Martin, Jeanne; May, John; Pierce, Elsie; Stanberry, Linda

1996-01-01

This paper describes an implementation of the proposed MPI-IO (Message Passing Interface - Input/Output) standard for parallel I/O. Our system uses third-party transfer to move data over an external network between the processors where it is used and the I/O devices where it resides. Data travels directly from source to destination, without the need for shuffling it among processors or funneling it through a central node. Our distributed server model lets multiple compute nodes share the burden of coordinating data transfers. The system is built on the High Performance Storage System (HPSS), and a prototype version runs on a Meiko CS-2 parallel computer.

Input/output behavior of supercomputing applications

NASA Technical Reports Server (NTRS)

Miller, Ethan L.

1991-01-01

The collection and analysis of supercomputer I/O traces and their use in a collection of buffering and caching simulations are described. This serves two purposes. First, it gives a model of how individual applications running on supercomputers request file system I/O, allowing system designer to optimize I/O hardware and file system algorithms to that model. Second, the buffering simulations show what resources are needed to maximize the CPU utilization of a supercomputer given a very bursty I/O request rate. By using read-ahead and write-behind in a large solid stated disk, one or two applications were sufficient to fully utilize a Cray Y-MP CPU.

Interorganizational Systems Adoption: A Socio-Technical Perspective

NASA Astrophysics Data System (ADS)

Bunker, Deborah; Kautz, Karlheinz; Pyne, Clayton

This paper discusses a case study of an electronic data interchange (EDI) interorganizational system (IOS) adoption project between two organizations (ProvideCo and BuildCo) highlighting that IOS adoption is not only technological in nature and orientation but that organizational factors also play their part. As a result of the case analysis and key findings, an interorganizational collaboration model (Barratt 2004) is amended to explain and highlight the effect of organizational factors on IOS adoption. The amended model includes the relationship of technology (IOS) adoption to cross-functional collaborative activities and risk, power, opportunism, and trust.

Parallel File System I/O Performance Testing On LANL Clusters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiens, Isaac Christian; Green, Jennifer Kathleen

2016-08-18

These are slides from a presentation on parallel file system I/O performance testing on LANL clusters. I/O is a known bottleneck for HPC applications. Performance optimization of I/O is often required. This summer project entailed integrating IOR under Pavilion and automating the results analysis. The slides cover the following topics: scope of the work, tools utilized, IOR-Pavilion test workflow, build script, IOR parameters, how parameters are passed to IOR, *run_ior: functionality, Python IOR-Output Parser, Splunk data format, Splunk dashboard and features, and future work.

Transition from Legacy to Connectivity Solution for Infrastructure Control of Smart Municipal Systems

NASA Astrophysics Data System (ADS)

Zabasta, A.; Kunicina, N.; Kondratjevs, K.

2017-06-01

Collaboration between heterogeneous systems and architectures is not an easy problem in the automation domain. By now, utilities and suppliers encounter real problems due to underestimated costs of technical solutions, frustration in selecting technical solutions relevant for local needs, and incompatibilities between a plenty of protocols and appropriate solutions. The paper presents research on creation of architecture of smart municipal systems in a local cloud of services that apply SOA and IoT approaches. The authors of the paper have developed a broker that applies orchestration services and resides on a gateway, which provides adapter and protocol translation functions, as well as applies a tool for wiring together hardware devices, APIs and online services.

Live interactive computer music performance practice

NASA Astrophysics Data System (ADS)

Wessel, David

2002-05-01

A live-performance musical instrument can be assembled around current lap-top computer technology. One adds a controller such as a keyboard or other gestural input device, a sound diffusion system, some form of connectivity processor(s) providing for audio I/O and gestural controller input, and reactive real-time native signal processing software. A system consisting of a hand gesture controller; software for gesture analysis and mapping, machine listening, composition, and sound synthesis; and a controllable radiation pattern loudspeaker are described. Interactivity begins in the set up wherein the speaker-room combination is tuned with an LMS procedure. This system was designed for improvisation. It is argued that software suitable for carrying out an improvised musical dialog with another performer poses special challenges. The processes underlying the generation of musical material must be very adaptable, capable of rapid changes in musical direction. Machine listening techniques are used to help the performer adapt to new contexts. Machine learning can play an important role in the development of such systems. In the end, as with any musical instrument, human skill is essential. Practice is required not only for the development of musically appropriate human motor programs but for the adaptation of the computer-based instrument as well.

Using Mobile TLA as a Logic for Dynamic I/O Automata

NASA Astrophysics Data System (ADS)

Kapus, Tatjana

Input/Output (I/O) automata and the Temporal Logic of Actions (TLA) are two well-known techniques for the specification and verification of concurrent systems. Over the past few years, they have been extended to the so-called dynamic I/O automata and, respectively, Mobile TLA (MTLA) in order to be more appropriate for mobile agent systems. Dynamic I/O automata is just a mathematical model, whereas MTLA is a logic with a formally defined language. In this paper, therefore, we investigate how MTLA could be used as a formal language for the specification of dynamic I/O automata. We do this by writing an MTLA specification of a travel agent system which has been specified semi-formally in the literature on that model. In this specification, we deal with always existing agents as well as with an initially unknown number of dynamically created agents, with mobile and non-mobile agents, with I/O-automata-style communication, and with the changing communication capabilities of mobile agents. We have previously written a TLA specification of this system. This paper shows that an MTLA specification of such a system can be more elegant and faithful to the dynamic I/O automata definition because the agent existence and location can be expressed directly by using agent and location names instead of special variables as in TLA. It also shows how the reuse of names for dynamically created and destroyed agents within the dynamic I/O automata framework can be specified in MTLA.

TTEO (Things Talk to Each Other): Programming Smart Spaces Based on IoT Systems.

PubMed

Yun, Jaeseok; Ahn, Il-Yeup; Choi, Sung-Chan; Kim, Jaeho

2016-04-01

The Internet of Things allows things in the world to be connected to each other and enables them to automate daily tasks without human intervention, eventually building smart spaces. This article demonstrates a prototype service based on the Internet of Things, TTEO (Things Talk to Each Other). We present the full details on the system architecture and the software platforms for IoT servers and devices, called Mobius and &Cube, respectively, complying with the globally-applicable IoT standards, oneM2M, a unique identification scheme for a huge number of IoT devices, and service scenarios with an intuitive smartphone app. We hope that our approach will help developers and lead users for IoT devices and application services to establish an emerging IoT ecosystem, just like the ecosystem for smartphones and mobile applications.

TTEO (Things Talk to Each Other): Programming Smart Spaces Based on IoT Systems

PubMed Central

Yun, Jaeseok; Ahn, Il-Yeup; Choi, Sung-Chan; Kim, Jaeho

2016-01-01

The Internet of Things allows things in the world to be connected to each other and enables them to automate daily tasks without human intervention, eventually building smart spaces. This article demonstrates a prototype service based on the Internet of Things, TTEO (Things Talk to Each Other). We present the full details on the system architecture and the software platforms for IoT servers and devices, called Mobius and &Cube, respectively, complying with the globally-applicable IoT standards, oneM2M, a unique identification scheme for a huge number of IoT devices, and service scenarios with an intuitive smartphone app. We hope that our approach will help developers and lead users for IoT devices and application services to establish an emerging IoT ecosystem, just like the ecosystem for smartphones and mobile applications. PMID:27043578

Science Rationale for the Io Volcano Observer (IVO) Mission Concept

NASA Astrophysics Data System (ADS)

McEwen, Alfred; Turtle, Elizabeth

2012-07-01

The Io Volcano Observer (IVO) mission can explore the rich array of interconnected orbital, geophysical, atmospheric, and plasma phenomena surrounding the most volcanically active world in the Solar System. Io is the only place in the Solar System (including Earth) where we can watch very large-scale silicate volcanic processes in action, and it provides unique insight into high-temperature and high effusion-rate volcanic processes that were important in the early histories of the terrestrial planets. Io is also the best target at which to study tidal heating, which greatly expands the habitable zones of planetary systems. Moreover, the coupled orbital-tidal evolution is key to understanding the thermal histories of Europa and Ganymede. Io is always inside the intense radiation belt of Jupiter, so a radiation-mitigation strategy has been developed. An inclined orbit that passes Io at high velocity (˜19 km/s) near its perijove point keeps the total ionizing dose to ˜10 krad (behind 2.5 mm or 100 mils Al) per encounter. Nevertheless, the dose rate is high near Io so some science instruments have special design considerations to minimize noise. The IVO spacecraft must be agile enough (rapid turning and settling) for high-stability targeted observations during close encounters. The inclined orbit provides nearly pole-to-pole flybys of Io, which enables some of the highest-priority Io science such as understanding the polar heat flow and electrical conductivity of Io's mantle (which may contain a magma ocean). Key science instruments include narrow- and wide-angle cameras, magnetometers, a thermal mapper, neutral mass spectrometers, and plasma ion analyzers. NASA's 2011 Decadal Survey for planetary science identified an Io mission similar to IVO as one of seven options for the next two New Frontiers mission opportunities. The Galileo (GLL) mission and payload were designed prior to the Voyager 1 flyby and discovery of Io's active volcanism, so they were not designed to meet key Io measurement requirements, and the failed high-gain antennae resulted in severely limited data return for a world that is highly variable in space, time, and wavelength. IVO will be designed specifically to address Io science as currently understood and will return, on every orbit, ˜100x the total Io data return of GLL over 8 years. The Jupiter Icy Moon Explorer (JUICE) mission concept from ESA could provide complementary monitoring but does not include close encounters with Io.

Development of a novel SCADA system for laboratory testing.

PubMed

Patel, M; Cole, G R; Pryor, T L; Wilmot, N A

2004-07-01

This document summarizes the supervisory control and data acquisition (SCADA) system that allows communication with, and controlling the output of, various I/O devices in the renewable energy systems and components test facility RESLab. This SCADA system differs from traditional SCADA systems in that it supports a continuously changing operating environment depending on the test to be performed. The SCADA System is based on the concept of having one Master I/O Server and multiple client computer systems. This paper describes the main features and advantages of this dynamic SCADA system, the connections of various field devices to the master I/O server, the device servers, and numerous software features used in the system. The system is based on the graphical programming language "LabVIEW" and its "Datalogging and Supervisory Control" (DSC) module. The DSC module supports a real-time database called the "tag engine," which performs the I/O operations with all field devices attached to the master I/O server and communications with the other tag engines running on the client computers connected via a local area network. Generic and detailed communication block diagrams illustrating the hierarchical structure of this SCADA system are presented. The flow diagram outlining a complete test performed using this system in one of its standard configurations is described.

Ontology Development and Evolution in the Accident Investigation Domain

NASA Technical Reports Server (NTRS)

Carvalho, Robert; Berrios, Dan; Williams, James

2004-01-01

InvestiigationOrganizer (IO) is a collaborative semantic web system designed to support the conduct of mishap investigations. IO provides a common repository for a wide range of mishap related information, allowing investigators to integrate evidence, causal models, and investigation results. IO has been used to support investigations ranging from a small property damage case to the loss of the Space Shuttle Columbia. Through IO'S use in these investigations, we have learned significant lessons? about the application of ontologies and semantic systems to solving real-world problems. This paper will describe the development of the ontology within IO, from the initial development, its growth in response to user requests during use in investigations, and the recent work that was done to control the results of that growth. This paper will also describe the lessons learned from this experience and how they may apply to the implementaton of future ontologies and semantic systems.

Toward Millions of File System IOPS on Low-Cost, Commodity Hardware

PubMed Central

Zheng, Da; Burns, Randal; Szalay, Alexander S.

2013-01-01

We describe a storage system that removes I/O bottlenecks to achieve more than one million IOPS based on a user-space file abstraction for arrays of commodity SSDs. The file abstraction refactors I/O scheduling and placement for extreme parallelism and non-uniform memory and I/O. The system includes a set-associative, parallel page cache in the user space. We redesign page caching to eliminate CPU overhead and lock-contention in non-uniform memory architecture machines. We evaluate our design on a 32 core NUMA machine with four, eight-core processors. Experiments show that our design delivers 1.23 million 512-byte read IOPS. The page cache realizes the scalable IOPS of Linux asynchronous I/O (AIO) and increases user-perceived I/O performance linearly with cache hit rates. The parallel, set-associative cache matches the cache hit rates of the global Linux page cache under real workloads. PMID:24402052

Toward Millions of File System IOPS on Low-Cost, Commodity Hardware.

PubMed

Zheng, Da; Burns, Randal; Szalay, Alexander S

2013-01-01

We describe a storage system that removes I/O bottlenecks to achieve more than one million IOPS based on a user-space file abstraction for arrays of commodity SSDs. The file abstraction refactors I/O scheduling and placement for extreme parallelism and non-uniform memory and I/O. The system includes a set-associative, parallel page cache in the user space. We redesign page caching to eliminate CPU overhead and lock-contention in non-uniform memory architecture machines. We evaluate our design on a 32 core NUMA machine with four, eight-core processors. Experiments show that our design delivers 1.23 million 512-byte read IOPS. The page cache realizes the scalable IOPS of Linux asynchronous I/O (AIO) and increases user-perceived I/O performance linearly with cache hit rates. The parallel, set-associative cache matches the cache hit rates of the global Linux page cache under real workloads.

Infinite order sudden approximation for rotational energy transfer in gaseous mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goldflam, R.; Green, S.; Kouri, D.J.

1977-11-01

Rotational energy transfer in gaseous mixtures has been considered within the framework of the infinite order sudden (IOS) approximation. A new derivation of the IOS from the coupled states Lippmann--Schwinger equation is given. This approach shows the relation between the IOS and CS T matrices and also shows in a rather transparent fashion Sencrest's result that the IOS method does not truncate closed channels but rather employs a closure relation to sum over all rotor states. The general CS effective cross section formula for relaxation processes is used, along with the IOS approximation to the CS T matrix, to derivemore » the general IOS effctive cross section.Factorization permits one to calculate other types of cross sections if any one type of cross section has been obtained by some procedure. The functional form can also be used to compact data. This formalism has been applied to calculate pressure broadening for the systems HD--He, HCl--He, CO--He, HCN--He, HCl--Ar, and CO/sub 2/--Ar. To test the IOS approximation, comparisons have been made to the CS results, which are known to be accurate for all these systems. The IOS approximation is found to be very accurate whenever the rotor spacings are small compared to the kinetic energy, provided closed channels do not play too great a role. For the systems CO--He, HCN--He, and CO/sub 2/--Ar, these conditions are well satisfied and the IOS is found to yield results accurate to within 10%--15%.« less

Design, implementation, and evaluation of an Internet of Things (IoT) network system for restaurant food waste management.

PubMed

Wen, Zongguo; Hu, Shuhan; De Clercq, Djavan; Beck, M Bruce; Zhang, Hua; Zhang, Huanan; Fei, Fan; Liu, Jianguo

2018-03-01

Catering companies around the world generate tremendous amounts of waste; those in China are no exception. The paper discusses the design, implementation, and evaluation of a sensor-based Internet of Things (IoT) network technology for improving the management of restaurant food waste (RFW) in the city of Suzhou, China. This IoT-based system encompasses the generation, collection, transportation and final disposal of RFW. The Suzhou case study comprised four steps: (1) examination of the required functionality of an IoT-enabled system in the specific context of Suzhou; (2) configuration of the system architecture, both software and hardware components, according to the identified functionality; (3) installation of the components of the IoT system at the facilities of the stakeholders across the RFW generation-collection-transportation-disposal value chain; and (4) evaluation of the performance of the entire system, based on data from three years of operation. The results show that the system had a strong impact. Positive results include: (1) better management of RFW generation, as evidenced by a 20.5% increase in RFW collected via official channels and a 207% increase in the number of RFW generators under official contract; (2) better law enforcement in response to RFW malpractice, enabled by the monitoring capabilities of the IoT system; and (3) an overall reduction in illicit RFW activities and better process optimization across the RFW value chain. Negative results include: (1) Radio-frequency identification (RFID) tags need to be renewed often due to the frequent handling of waste bins, thus increasing operating costs; (2) dynamic/automatic weight sensors had a higher degree of error than the more time-consuming static/manual weighing method; and (3) there were disagreements between the city's government agencies about how to interpret data from the IoT system, which led to some inefficiencies in management. In sum, the Suzhou IoT system enabled data-driven management of RFW and had a net positive impact for the stakeholders involved. Copyright © 2017. Published by Elsevier Ltd.

Internet of Things in Higher Education: A Study on Future Learning

NASA Astrophysics Data System (ADS)

Aldowah, Hanan; Rehman, Shafiq Ul; Ghazal, Samar; Naufal Umar, Irfan

2017-09-01

In the coming years, technology will impact the learning experience in many ways. Internet of Things (IoT) continues to confirm its important position in the context of Information and Communication Technologies and the development of society. With the support of IoT, institutions can enhance learning outcomes by providing more affluent learning experiences, improved operational efficiency, and by gaining real-time, actionable insight into student performance. The purpose of this study is to find out the potential of IoT in higher education and how to maximize its benefits and reducing the risks involved with it. Further efforts are necessary for releasing the full potential of IoT systems and technologies. Therefore, this paper presents a study about the impact of IoT on higher education especially universities. IoT stands to change dramatically the way universities work, and enhance student learning in many disciplines and at any level. It has huge potential for universities or any other educational institutions; if well prepared to ensure widespread and successful implementation by leadership, staff, and students. IoT needs development where universities can lead. Academics, researchers, and students are in a unique place to lead the discovery and development of IoT systems, devices, applications, and services. Moreover, this paper provides an evidences about the future of IoT in the higher education during the next few years, which have offered by a number of research organizations and enterprises. On the other hand, IoT also brings tremendous challenges to higher education. Hence, this paper also presents the perspective on the challenges of IoT in higher education.

A Proof-of-Concept for Semantically Interoperable Federation of IoT Experimentation Facilities.

PubMed

Lanza, Jorge; Sanchez, Luis; Gomez, David; Elsaleh, Tarek; Steinke, Ronald; Cirillo, Flavio

2016-06-29

The Internet-of-Things (IoT) is unanimously identified as one of the main pillars of future smart scenarios. The potential of IoT technologies and deployments has been already demonstrated in a number of different application areas, including transport, energy, safety and healthcare. However, despite the growing number of IoT deployments, the majority of IoT applications tend to be self-contained, thereby forming application silos. A lightweight data centric integration and combination of these silos presents several challenges that still need to be addressed. Indeed, the ability to combine and synthesize data streams and services from diverse IoT platforms and testbeds, holds the promise to increase the potentiality of smart applications in terms of size, scope and targeted business context. In this article, a proof-of-concept implementation that federates two different IoT experimentation facilities by means of semantic-based technologies will be described. The specification and design of the implemented system and information models will be described together with the practical details of the developments carried out and its integration with the existing IoT platforms supporting the aforementioned testbeds. Overall, the system described in this paper demonstrates that it is possible to open new horizons in the development of IoT applications and experiments at a global scale, that transcend the (silo) boundaries of individual deployments, based on the semantic interconnection and interoperability of diverse IoT platforms and testbeds.

A Proof-of-Concept for Semantically Interoperable Federation of IoT Experimentation Facilities

PubMed Central

Lanza, Jorge; Sanchez, Luis; Gomez, David; Elsaleh, Tarek; Steinke, Ronald; Cirillo, Flavio

2016-01-01

The Internet-of-Things (IoT) is unanimously identified as one of the main pillars of future smart scenarios. The potential of IoT technologies and deployments has been already demonstrated in a number of different application areas, including transport, energy, safety and healthcare. However, despite the growing number of IoT deployments, the majority of IoT applications tend to be self-contained, thereby forming application silos. A lightweight data centric integration and combination of these silos presents several challenges that still need to be addressed. Indeed, the ability to combine and synthesize data streams and services from diverse IoT platforms and testbeds, holds the promise to increase the potentiality of smart applications in terms of size, scope and targeted business context. In this article, a proof-of-concept implementation that federates two different IoT experimentation facilities by means of semantic-based technologies will be described. The specification and design of the implemented system and information models will be described together with the practical details of the developments carried out and its integration with the existing IoT platforms supporting the aforementioned testbeds. Overall, the system described in this paper demonstrates that it is possible to open new horizons in the development of IoT applications and experiments at a global scale, that transcend the (silo) boundaries of individual deployments, based on the semantic interconnection and interoperability of diverse IoT platforms and testbeds. PMID:27367695

INTERDISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Polar Mixing Optical Phonon Spectra in Wurtzite GaN Cylindrical Quantum Dots: Quantum Size and Dielectric Effects

NASA Astrophysics Data System (ADS)

Zhang, Li; Liao, Jian-Shang

2010-05-01

The interface-optical-propagating (IO-PR) mixing phonon modes of a quasi-zero-dimensional (QoD) wurtzite cylindrical quantum dot (QD) structure are derived and studied by employing the macroscopic dielectric continuum model. The analytical phonon states of IO-PR mixing modes are given. It is found that there are two types of IO-PR mixing phonon modes, i.e. ρ-IO/z-PR mixing modes and the z-IO/ρ-PR mixing modes existing in QoD wurtzite QDs. And each IO-PR mixing modes also have symmetrical and antisymmetrical forms. Via a standard procedure of field quantization, the Fröhlich Hamiltonians of electron-(IO-PR) mixing phonons interaction are obtained. Numerical calculations on a wurtzite GaN cylindrical QD are performed. The results reveal that both the radial-direction size and the axial-direction size as well as the dielectric matrix have great influence on the dispersive frequencies of the IO-PR mixing phonon modes. The limiting features of dispersive curves of these phonon modes are discussed in depth. The phonon modes “reducing" behavior of wurtzite quantum confined systems has been observed obviously in the structures. Moreover, the degenerating behaviors of the IO-PR mixing phonon modes in wurtzite QoD QDs to the IO modes and PR modes in wurtzite Q2D QW and Q1D QWR systems are analyzed deeply from both of the viewpoints of physics and mathematics.

On the Internet of Things, smart cities and the WHO Healthy Cities

PubMed Central

2014-01-01

This article gives a brief overview of the Internet of Things (IoT) for cities, offering examples of IoT-powered 21st century smart cities, including the experience of the Spanish city of Barcelona in implementing its own IoT-driven services to improve the quality of life of its people through measures that promote an eco-friendly, sustainable environment. The potential benefits as well as the challenges associated with IoT for cities are discussed. Much of the 'big data' that are continuously generated by IoT sensors, devices, systems and services are geo-tagged or geo-located. The importance of having robust, intelligent geospatial analytics systems in place to process and make sense of such data in real time cannot therefore be overestimated. The authors argue that IoT-powered smart cities stand better chances of becoming healthier cities. The World Health Organization (WHO) Healthy Cities Network and associated national networks have hundreds of member cities around the world that could benefit from, and harness the power of, IoT to improve the health and well-being of their local populations. PMID:24669838

On the Internet of Things, smart cities and the WHO Healthy Cities.

PubMed

Kamel Boulos, Maged N; Al-Shorbaji, Najeeb M

2014-03-27

This article gives a brief overview of the Internet of Things (IoT) for cities, offering examples of IoT-powered 21st century smart cities, including the experience of the Spanish city of Barcelona in implementing its own IoT-driven services to improve the quality of life of its people through measures that promote an eco-friendly, sustainable environment. The potential benefits as well as the challenges associated with IoT for cities are discussed. Much of the 'big data' that are continuously generated by IoT sensors, devices, systems and services are geo-tagged or geo-located. The importance of having robust, intelligent geospatial analytics systems in place to process and make sense of such data in real time cannot therefore be overestimated. The authors argue that IoT-powered smart cities stand better chances of becoming healthier cities. The World Health Organization (WHO) Healthy Cities Network and associated national networks have hundreds of member cities around the world that could benefit from, and harness the power of, IoT to improve the health and well-being of their local populations.

Tuning HDF5 for Lustre File Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howison, Mark; Koziol, Quincey; Knaak, David

2010-09-24

HDF5 is a cross-platform parallel I/O library that is used by a wide variety of HPC applications for the flexibility of its hierarchical object-database representation of scientific data. We describe our recent work to optimize the performance of the HDF5 and MPI-IO libraries for the Lustre parallel file system. We selected three different HPC applications to represent the diverse range of I/O requirements, and measured their performance on three different systems to demonstrate the robustness of our optimizations across different file system configurations and to validate our optimization strategy. We demonstrate that the combined optimizations improve HDF5 parallel I/O performancemore » by up to 33 times in some cases running close to the achievable peak performance of the underlying file system and demonstrate scalable performance up to 40,960-way concurrency.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

D'Azevedo, Eduardo; Abbott, Stephen; Koskela, Tuomas

The XGC fusion gyrokinetic code combines state-of-the-art, portable computational and algorithmic technologies to enable complicated multiscale simulations of turbulence and transport dynamics in ITER edge plasma on the largest US open-science computer, the CRAY XK7 Titan, at its maximal heterogeneous capability, which have not been possible before due to a factor of over 10 shortage in the time-to-solution for less than 5 days of wall-clock time for one physics case. Frontier techniques such as nested OpenMP parallelism, adaptive parallel I/O, staging I/O and data reduction using dynamic and asynchronous applications interactions, dynamic repartitioning.

Variations of System IV period of the sulfur ions in the Io torus for the volcanic event in 2015 observed by the HISAKI/EXCEED

NASA Astrophysics Data System (ADS)

Ryo, A.; Misawa, H.; Tsuchiya, F.; Kagitani, M.; Yoshioka, K.; Yoshikawa, I.; Kimura, T.; Murakami, G.; Yamazaki, A.

2017-12-01

Previous ground-based and probe observations of Io plasma torus (IPT) in various wavelengths have detected a periodic variation which is longer than System III period (9.925 h). It has been called System IV period. Although various ideas to explain the origin of System IV period are proposed , little progress has been made. A previous study reported that the System IV period was 10.07 h during the Cassini's Jupiter flyby in 2000. This period was shorter than the typical period of 10.21h (Brown 1995). The Io's volcanic event just before Cassini's flyby might shorten the System IV period (Steffl et al., 2006). However, the certainty of this inference is not clear from the Cassini observation. Here, we analyzed time variations in intensities of EUV emissions from IPT obtained by the HISAKI satellite to understand the mechanism responsible for the System IV period and the influence of Io's volcanic event on IPT. The data used in this study was obtained from Dec. 2014 to the middle of May 2015. During this period, the Io's volcanic event from Jan. to Mar. 2015 was reported from the observation of Iogenic sodium emission (Yoneda et al., 2015). To find variations of the System IV period, the temporal variation of System III longitude at peak EUV intensity was derived by fitting light curves of three ion species (S II 76.5 nm + 126 nm, S III 68 nm, and S IV 65.7 nm + 140.5 nm). The System IV periods of S II before and after the Io's volcanic event were 10.16±0.008 h and 10.03±0.006 h, respectively. On the other hands, the System IV period of S II was 9.95±0.003 h during the Io's volcanic event. This is the first observational evidence which shows that the System IV period has shortened during the Io's volcanic event, which is consistent with the result from Cassini observation. Origin of the System IV period has been discussed with sub-corotation of plasma in IPT. Since the sub-corotation occurs due to mass loading of newly picked-up ions into IPT, it is expected that the System IV period becomes long during Io's volcanic event. However, the result shows the opposite feature and will give important information to constrain the origin of the System IV period. To verify above consideration, we will derive time variation in plasma parameters in IPT from the HISAKI data with plasma diagnosis analysis. This analysis will enable us to constrain the origin of the System IV period.

Design and Implementation of an Enterprise Internet of Things

NASA Astrophysics Data System (ADS)

Sun, Jing; Zhao, Huiqun; Wang, Ka; Zhang, Houyong; Hu, Gongzhu

Since the notion of "Internet of Things" (IoT) introduced about 10 years ago, most IoT research has focused on higher level issues, such as strategies, architectures, standardization, and enabling technologies, but studies of real cases of IoT are still lacking. In this paper, a real case of Internet of Things called ZB IoT is introduced. It combines the Service Oriented Architecture (SOA) with EPC global standards in the system design, and focuses on the security and extensibility of IoT in its implementation.

I/O load balancing for big data HPC applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paul, Arnab K.; Goyal, Arpit; Wang, Feiyi

High Performance Computing (HPC) big data problems require efficient distributed storage systems. However, at scale, such storage systems often experience load imbalance and resource contention due to two factors: the bursty nature of scientific application I/O; and the complex I/O path that is without centralized arbitration and control. For example, the extant Lustre parallel file system-that supports many HPC centers-comprises numerous components connected via custom network topologies, and serves varying demands of a large number of users and applications. Consequently, some storage servers can be more loaded than others, which creates bottlenecks and reduces overall application I/O performance. Existing solutionsmore » typically focus on per application load balancing, and thus are not as effective given their lack of a global view of the system. In this paper, we propose a data-driven approach to load balance the I/O servers at scale, targeted at Lustre deployments. To this end, we design a global mapper on Lustre Metadata Server, which gathers runtime statistics from key storage components on the I/O path, and applies Markov chain modeling and a minimum-cost maximum-flow algorithm to decide where data should be placed. Evaluation using a realistic system simulator and a real setup shows that our approach yields better load balancing, which in turn can improve end-to-end performance.« less

Toward an in-situ analytics and diagnostics framework for earth system models

NASA Astrophysics Data System (ADS)

Anantharaj, Valentine; Wolf, Matthew; Rasch, Philip; Klasky, Scott; Williams, Dean; Jacob, Rob; Ma, Po-Lun; Kuo, Kwo-Sen

2017-04-01

The development roadmaps for many earth system models (ESM) aim for a globally cloud-resolving model targeting the pre-exascale and exascale systems of the future. The ESMs will also incorporate more complex physics, chemistry and biology - thereby vastly increasing the fidelity of the information content simulated by the model. We will then be faced with an unprecedented volume of simulation output that would need to be processed and analyzed concurrently in order to derive the valuable scientific results. We are already at this threshold with our current generation of ESMs at higher resolution simulations. Currently, the nominal I/O throughput in the Community Earth System Model (CESM) via Parallel IO (PIO) library is around 100 MB/s. If we look at the high frequency I/O requirements, it would require an additional 1 GB / simulated hour, translating to roughly 4 mins wallclock / simulated-day => 24.33 wallclock hours / simulated-model-year => 1,752,000 core-hours of charge per simulated-model-year on the Titan supercomputer at the Oak Ridge Leadership Computing Facility. There is also a pending need for 3X more volume of simulation output . Meanwhile, many ESMs use instrument simulators to run forward models to compare model simulations against satellite and ground-based instruments, such as radars and radiometers. The CFMIP Observation Simulator Package (COSP) is used in CESM as well as the Accelerated Climate Model for Energy (ACME), one of the ESMs specifically targeting current and emerging leadership-class computing platforms These simulators can be computationally expensive, accounting for as much as 30% of the computational cost. Hence the data are often written to output files that are then used for offline calculations. Again, the I/O bottleneck becomes a limitation. Detection and attribution studies also use large volume of data for pattern recognition and feature extraction to analyze weather and climate phenomenon such as tropical cyclones, atmospheric rivers, blizzards, etc. It is evident that ESMs need an in-situ framework to decouple the diagnostics and analytics from the prognostics and physics computations of the models so that the diagnostic computations could be performed concurrently without limiting model throughput. We are designing a science-driven online analytics framework for earth system models. Our approach is to adopt several data workflow technologies, such as the Adaptable IO System (ADIOS), being developed under the U.S. Exascale Computing Project (ECP) and integrate these to allow for extreme performance IO, in situ workflow integration, science-driven analytics and visualization all in a easy to use computational framework. This will allow science teams to write data 100-1000 times faster and seamlessly move from post processing the output for validation and verification purposes to performing these calculations in situ. We can easily and knowledgeably envision a near-term future where earth system models like ACME and CESM will have to address not only the challenges of the volume of data but also need to consider the velocity of the data. The earth system model of the future in the exascale era, as they incorporate more complex physics at higher resolutions, will be able to analyze more simulation content without having to compromise targeted model throughput.

Influences of spring-to-summer sea surface temperatures over different Indian Ocean domains on the Asian summer monsoon

NASA Astrophysics Data System (ADS)

Li, Zhenning; Yang, Song

2017-11-01

The influences of spring-to-summer sea surface temperature (SST) anomalies in different domains of the Indian Ocean (IO) on the Asian summer monsoon are investigated by conducting a series of numerical experiments using the NCAR CAM4 model. It is found that, to a certain extent, the springtime IO SST anomalies can persist to the summer season. The spring-to-summer IO SST anomalies associated with the IO basin warming mode are strongly linked to the summer climate over Asia, especially the South Asian monsoon (SAM) and the East Asian monsoon. Among this connection, the warming of tropical IO plays the most critical role, and the warming of southern IO is important for monsoon variation and prediction prior to the full development of the monsoon. The atmospheric response to IO basin wide warming is similar with that to tropical IO warming. The influence of northern IO warming on the SAM, however, is opposite to the effect of southern IO warming. Meanwhile, the discrepancies between the results from idealized SST forcing simulations and observations, especially for the southern IO, reveal that the dominant role of air-sea interaction in the monsoon-IO coupled system cannot be ignored. Moreover, the springtime northern IO warming seems to favor an early onset or a stronger persistence of the SAM.

Biologically Inspired Behavioral Strategies for Autonomous Aerial Explorers on Mars

NASA Technical Reports Server (NTRS)

Plice, Laura; Pisanich, Greg; Lau, Benton; Young, Larry A.

2002-01-01

The natural world is a rich source of problem- solving approaches. This paper discusses the feasibility and technical challenges underlying mimicking, or analogously adapting, biological behavioral strategies to mission/flight planning for aerial vehicles engaged in planetary exploration. Two candidate concepts based on natural resource utilization and searching behaviors are adapted io technological applications. Prototypes and test missions addressing the difficulties of implementation and their solutions are also described.

IoT Contextual Factors on Healthcare.

PubMed

Michalakis, Konstantinos; Caridakis, George

2017-01-01

With the emergence of the Internet of Things, new services in healthcare will be available and existing systems will be integrated in the IoT framework, providing automated medical supervision and efficient medical treatment. Context awareness plays a critical role in realizing the vision of the IoT, providing rich contextual information that can help the system act more efficiently. Since context in healthcare has its unique characteristics, it is necessary to define an appropriate context aware framework for healthcare IoT applications. We identify this context as perceived in healthcare applications and describe the context aware procedures. We also present an architecture that connects the sensors that measure biometric data with the sensory networks of the environment and the various IoT middleware that reside in the geographical area. Finally, we discuss the challenges for the realization of this vision.

Distributed Sensor Systems and Electromechanical Analog Facility

DTIC Science & Technology

1980-01-01

interfaces (parallel I/O, modems , etc.) real time operating systems (perhaps a short survey of what is available in the industry today), data...consists of a LSI-11 microprocessor, 56K bytes of memory, and serial and parallel I/O boards. 2.1.7 Disk controller The standard disk controller...with MTS via the modems connected to the LSI-lls. This pseudodevice cannot be reassigned. OSWIT I/O AND INTERRUPT STRUCTURE 137 OSWIT

Impact of motion-associated noise on intrinsic optical signal imaging in humans with optical coherence tomography

PubMed Central

Teussink, Michel M.; Cense, Barry; van Grinsven, Mark J.J.P.; Klevering, B. Jeroen; Hoyng, Carel B.; Theelen, Thomas

2015-01-01

A growing body of evidence suggests that phototransduction can be studied in the human eye in vivo by imaging of fast intrinsic optical signals (IOS). There is consensus concerning the limiting influence of motion-associated imaging noise on the reproducibility of IOS-measurements, especially in those employing spectral-domain optical coherence tomography (SD-OCT). However, no study to date has conducted a comprehensive analysis of this noise in the context of IOS-imaging. In this study, we discuss biophysical correlates of IOS, and we address motion-associated imaging noise by providing correctional post-processing methods. In order to avoid cross-talk of adjacent IOS of opposite signal polarity, cellular resolution and stability of imaging to the level of individual cones is likely needed. The optical Stiles-Crawford effect can be a source of significant IOS-imaging noise if alignment with the peak of the Stiles-Crawford function cannot be maintained. Therefore, complete head stabilization by implementation of a bite-bar may be critical to maintain a constant pupil entry position of the OCT beam. Due to depth-dependent sensitivity fall-off, heartbeat and breathing associated axial movements can cause tissue reflectivity to vary by 29% over time, although known methods can be implemented to null these effects. Substantial variations in reflectivity can be caused by variable illumination due to changes in the beam pupil entry position and angle, which can be reduced by an adaptive algorithm based on slope-fitting of optical attenuation in the choriocapillary lamina. PMID:26137369

Astronauts and IoT: Toward True Human-Autonomy Teaming

NASA Technical Reports Server (NTRS)

Vera, Alonso

2016-01-01

Advances in the area of Internet of Things (IoT) or Cyber-Physical Systems will have a significant impact on many areas of human activity and commercial/technological development. One application of importance to NASA is the need to make crews on deep space missions more independent from earth in both their routine activities and handling of unexpected events. IoT will allow increasingly intelligent systems to be aware of what humans are doing, what tools/resources they are using, and what help they might need in terms of procedure execution in tasks such as assembly, maintenance, repair, and perhaps even in more complex activities like medical interventions. This talk focuses on the convergence of research and technologies that will be needed to effect such intelligent systems based on IoT.

A Modular IoT Platform for Real-Time Indoor Air Quality Monitoring.

PubMed

Benammar, Mohieddine; Abdaoui, Abderrazak; Ahmad, Sabbir H M; Touati, Farid; Kadri, Abdullah

2018-02-14

The impact of air quality on health and on life comfort is well established. In many societies, vulnerable elderly and young populations spend most of their time indoors. Therefore, indoor air quality monitoring (IAQM) is of great importance to human health. Engineers and researchers are increasingly focusing their efforts on the design of real-time IAQM systems using wireless sensor networks. This paper presents an end-to-end IAQM system enabling measurement of CO₂, CO, SO₂, NO₂, O₃, Cl₂, ambient temperature, and relative humidity. In IAQM systems, remote users usually use a local gateway to connect wireless sensor nodes in a given monitoring site to the external world for ubiquitous access of data. In this work, the role of the gateway in processing collected air quality data and its reliable dissemination to end-users through a web-server is emphasized. A mechanism for the backup and the restoration of the collected data in the case of Internet outage is presented. The system is adapted to an open-source Internet-of-Things (IoT) web-server platform, called Emoncms, for live monitoring and long-term storage of the collected IAQM data. A modular IAQM architecture is adopted, which results in a smart scalable system that allows seamless integration of various sensing technologies, wireless sensor networks (WSNs) and smart mobile standards. The paper gives full hardware and software details of the proposed solution. Sample IAQM results collected in various locations are also presented to demonstrate the abilities of the system.

A Comprehensive Study on the Internet of Underwater Things: Applications, Challenges, and Channel Models †

PubMed Central

Wu, Geng-De; Huang, Chun-Ju

2017-01-01

The Internet of Underwater Things (IoUT) is a novel class of Internet of Things (IoT), and is defined as the network of smart interconnected underwater objects. IoUT is expected to enable various practical applications, such as environmental monitoring, underwater exploration, and disaster prevention. With these applications, IoUT is regarded as one of the potential technologies toward developing smart cities. To support the concept of IoUT, Underwater Wireless Sensor Networks (UWSNs) have emerged as a promising network system. UWSNs are different from the traditional Territorial Wireless Sensor Networks (TWSNs), and have several unique properties, such as long propagation delay, narrow bandwidth, and low reliability. These unique properties would be great challenges for IoUT. In this paper, we provide a comprehensive study of IoUT, and the main contributions of this paper are threefold: (1) we introduce and classify the practical underwater applications that can highlight the importance of IoUT; (2) we point out the differences between UWSNs and traditional TWSNs, and these differences are the main challenges for IoUT; and (3) we investigate and evaluate the channel models, which are the technical core for designing reliable communication protocols on IoUT. PMID:28640220

A Comprehensive Study on the Internet of Underwater Things: Applications, Challenges, and Channel Models.

PubMed

Kao, Chien-Chi; Lin, Yi-Shan; Wu, Geng-De; Huang, Chun-Ju

2017-06-22

The Internet of Underwater Things (IoUT) is a novel class of Internet of Things (IoT), and is defined as the network of smart interconnected underwater objects. IoUT is expected to enable various practical applications, such as environmental monitoring, underwater exploration, and disaster prevention. With these applications, IoUT is regarded as one of the potential technologies toward developing smart cities. To support the concept of IoUT, Underwater Wireless Sensor Networks (UWSNs) have emerged as a promising network system. UWSNs are different from the traditional Territorial Wireless Sensor Networks (TWSNs), and have several unique properties, such as long propagation delay, narrow bandwidth, and low reliability. These unique properties would be great challenges for IoUT. In this paper, we provide a comprehensive study of IoUT, and the main contributions of this paper are threefold: (1) we introduce and classify the practical underwater applications that can highlight the importance of IoUT; (2) we point out the differences between UWSNs and traditional TWSNs, and these differences are the main challenges for IoUT; and (3) we investigate and evaluate the channel models, which are the technical core for designing reliable communication protocols on IoUT.

High-Performance I/O: HDF5 for Lattice QCD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurth, Thorsten; Pochinsky, Andrew; Sarje, Abhinav

2015-01-01

Practitioners of lattice QCD/QFT have been some of the primary pioneer users of the state-of-the-art high-performance-computing systems, and contribute towards the stress tests of such new machines as soon as they become available. As with all aspects of high-performance-computing, I/O is becoming an increasingly specialized component of these systems. In order to take advantage of the latest available high-performance I/O infrastructure, to ensure reliability and backwards compatibility of data files, and to help unify the data structures used in lattice codes, we have incorporated parallel HDF5 I/O into the SciDAC supported USQCD software stack. Here we present the design andmore » implementation of this I/O framework. Our HDF5 implementation outperforms optimized QIO at the 10-20% level and leaves room for further improvement by utilizing appropriate dataset chunking.« less

High-Performance I/O: HDF5 for Lattice QCD

DOE PAGES

Kurth, Thorsten; Pochinsky, Andrew; Sarje, Abhinav; ...

2017-05-09

Practitioners of lattice QCD/QFT have been some of the primary pioneer users of the state-of-the-art high-performance-computing systems, and contribute towards the stress tests of such new machines as soon as they become available. As with all aspects of high-performance-computing, I/O is becoming an increasingly specialized component of these systems. In order to take advantage of the latest available high-performance I/O infrastructure, to ensure reliability and backwards compatibility of data files, and to help unify the data structures used in lattice codes, we have incorporated parallel HDF5 I/O into the SciDAC supported USQCD software stack. Here we present the design andmore » implementation of this I/O framework. Our HDF5 implementation outperforms optimized QIO at the 10-20% level and leaves room for further improvement by utilizing appropriate dataset chunking.« less

Io's Interaction with the Jovian Magnetosphere: Models of Particle Acceleration and Scattering

NASA Astrophysics Data System (ADS)

Crary, Frank Judson

1998-09-01

I develop models of electron acceleration and ion scattering which result from Io's interaction with the jovian magnetosphere. According to my models, Io initially generates transient currents and an Alfvenic disturbance when it first encounters a jovian magnetic field line, and the interaction would eventually settle into a system of steady Birkeland currents as the field line is advected downstream past Io and into Io's wake. I derive a model of wave propagation and electron acceleration by the Alfvenic transient, due to electron inertial effects. My numerical calculations show that the power and particle energy of the resulting electron beam are consistent with observations of the Io-related auroral spot and of Jupiter's S-burst decametric emissions. In the case of the steady currents and Io's wake. I show that these currents would drive instabilities and argue that electrostatic double layers would form in the high latitudes of the Io/Io wake flux tubes. I examine the role of these double layers in producing energetic electrons and estimate the likely electron energies and power. This model agrees with observations of a long arc in the jovian aurora, extending away from the Io-related spot, the L-burst decametric radio emissions and electron beams observed by the Galileo spacecraft in Io's wake. Finally, I consider the Galileo observations of ion cyclotron waves near Io. I use the absence of waves near the S and O gyrofrequencies to place limits on the source rate of heavy ions near Io. For a sufficiently low source rate, the thermal core population prevents ion cyclotron instabilities and wave growth. I use these limits to constrain the neutral column density of Io's exosphere and amount of plasma produced within 2 to 10 body radii of Io.

Synthesis, crystal structure and optical properties of two new layered cadmium iodates: Cd(IO{sub 3})X (X=Cl, OH)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Bing-Ping, E-mail: ybp@fjirsm.ac.cn; Mao, Jiang-Gao

Systematic explorations of new compounds in the cadmium iodate system by hydrothermal reactions led to two layered iodates, namely, Cd(IO{sub 3})X (X=Cl, OH). Cd(IO{sub 3})Cl crystallizes in the orthorhombic space group Cmca (No. 64) whereas Cd(IO{sub 3})(OH) crystallizes in the orthorhombic space group Pnma (No. 62). Cd(IO{sub 3})Cl displays a unique double layered structure composed of {sup 1}{sub ∞}[Cd−O{sub 3}Cl]{sub n} chains. Cadmium octahedrons form a 1D chain along the a-axis through edge sharing, and such chains are further interconnected via IO{sub 3} groups to form a special double layer on (020) plane. Cd(IO{sub 3})(OH) also exhibits a layered structuremore » that is composed of cadmium cations, IO{sub 3} groups and hydroxyl ions. Within a layer, chains of CdO{sub 6} edge-shared octahedra are observed along the b-axis. And these chains are connected by IO{sub 3} groups into a layer parallel to the bc plane. Spectroscopic characterizations, elemental analysis, and thermogravimetric analysis for the reported two compounds are also presented. - Graphical abstract: Two new layered cadmium iodates Cd(IO{sub 3})X (X=Cl, OH) are reported. Cd(IO{sub 3})Cl features a unique double layered structure whereas Cd(IO{sub 3})(OH) displays an ordinary layered structure. - Highlights: • Two new layered cadmium iodates Cd(IO{sub 3})X (X=Cl, OH) are reported. • Cd(IO{sub 3})Cl features a unique double layered structure. • Cd(IO{sub 3})(OH) displays an ordinary layered structure. • The spectroscopic and thermal properties have been studied in detail.« less

IoT-based smart garbage system for efficient food waste management.

PubMed

Hong, Insung; Park, Sunghoi; Lee, Beomseok; Lee, Jaekeun; Jeong, Daebeom; Park, Sehyun

2014-01-01

Owing to a paradigm shift toward Internet of Things (IoT), researches into IoT services have been conducted in a wide range of fields. As a major application field of IoT, waste management has become one such issue. The absence of efficient waste management has caused serious environmental problems and cost issues. Therefore, in this paper, an IoT-based smart garbage system (SGS) is proposed to reduce the amount of food waste. In an SGS, battery-based smart garbage bins (SGBs) exchange information with each other using wireless mesh networks, and a router and server collect and analyze the information for service provisioning. Furthermore, the SGS includes various IoT techniques considering user convenience and increases the battery lifetime through two types of energy-efficient operations of the SGBs: stand-alone operation and cooperation-based operation. The proposed SGS had been operated as a pilot project in Gangnam district, Seoul, Republic of Korea, for a one-year period. The experiment showed that the average amount of food waste could be reduced by 33%.

IoT-Based Smart Garbage System for Efficient Food Waste Management

PubMed Central

Lee, Jaekeun

2014-01-01

Owing to a paradigm shift toward Internet of Things (IoT), researches into IoT services have been conducted in a wide range of fields. As a major application field of IoT, waste management has become one such issue. The absence of efficient waste management has caused serious environmental problems and cost issues. Therefore, in this paper, an IoT-based smart garbage system (SGS) is proposed to reduce the amount of food waste. In an SGS, battery-based smart garbage bins (SGBs) exchange information with each other using wireless mesh networks, and a router and server collect and analyze the information for service provisioning. Furthermore, the SGS includes various IoT techniques considering user convenience and increases the battery lifetime through two types of energy-efficient operations of the SGBs: stand-alone operation and cooperation-based operation. The proposed SGS had been operated as a pilot project in Gangnam district, Seoul, Republic of Korea, for a one-year period. The experiment showed that the average amount of food waste could be reduced by 33%. PMID:25258730

In vitro and in vivo imaging and tracking of intestinal organoids from human induced pluripotent stem cells.

PubMed

Jung, Kwang Bo; Lee, Hana; Son, Ye Seul; Lee, Ji Hye; Cho, Hyun-Soo; Lee, Mi-Ok; Oh, Jung-Hwa; Lee, Jaemin; Kim, Seokho; Jung, Cho-Rok; Kim, Janghwan; Son, Mi-Young

2018-01-01

Human intestinal organoids (hIOs) derived from human pluripotent stem cells (hPSCs) have immense potential as a source of intestines. Therefore, an efficient system is needed for visualizing the stage of intestinal differentiation and further identifying hIOs derived from hPSCs. Here, 2 fluorescent biosensors were developed based on human induced pluripotent stem cell (hiPSC) lines that stably expressed fluorescent reporters driven by intestine-specific gene promoters Krüppel-like factor 5 monomeric Cherry (KLF5 mCherry ) and intestine-specific homeobox enhanced green fluorescence protein (ISX eGFP ). Then hIOs were efficiently induced from those transgenic hiPSC lines in which mCherry- or eGFP-expressing cells, which appeared during differentiation, could be identified in intact living cells in real time. Reporter gene expression had no adverse effects on differentiation into hIOs and proliferation. Using our reporter system to screen for hIO differentiation factors, we identified DMH1 as an efficient substitute for Noggin. Transplanted hIOs under the kidney capsule were tracked with fluorescence imaging (FLI) and confirmed histologically. After orthotopic transplantation, the localization of the hIOs in the small intestine could be accurately visualized using FLI. Our study establishes a selective system for monitoring the in vitro differentiation and for tracking the in vivo localization of hIOs and contributes to further improvement of cell-based therapies and preclinical screenings in the intestinal field.-Jung, K. B., Lee, H., Son, Y. S., Lee, J. H., Cho, H.-S., Lee, M.-O., Oh, J.-H., Lee, J., Kim, S., Jung, C.-R., Kim, J., Son, M.-Y. In vitro and in vivo imaging and tracking of intestinal organoids from human induced pluripotent stem cells. © FASEB.

Evaluation of display technologies for Internet of Things (IoT)

NASA Astrophysics Data System (ADS)

Sabo, Julia; Fegert, Tobias; Cisowski, Matthäus Stephanus; Marsal, Anatolij; Eichberger, Domenik; Blankenbach, Karlheinz

2017-02-01

Internet of Things (IoT) is a booming industry. We investigated several (semi-) professional IoT devices in combination with displays (focus on reflective technologies) and LEDs. First, these displays were compared for reflectance and ambient light performance. Two measurement set-ups with diffuse conditions were used for simulating typical indoor lighting conditions of IoT displays. E-paper displays were evaluated best as they combine a relative high reflectance with large contrast ratio. Reflective monochrome LCDs show a lower reflectance but are widely available. Second we studied IoT microprocessors interfaces to displays. A µP can drive single LEDs and one or two Seg 8 LED digits directly by GPIOs. Other display technologies require display controllers with a parallel or serial interface to the microprocessor as they need dedicated waveforms for driving the pixels. Most suitable are display modules with built-in display RAM as only pixel data have to be transferred which changes. A HDMI output (e.g. Raspberry Pi) results in high cost for the displays, therefore AMLCDs are not suitable for low to medium cost IoT systems. We compared and evaluated furthermore status indicators, icons, text and graphics IoT display systems regarding human machine interface (HMI) characteristics and effectiveness as well as power consumption. We found out that low resolution graphics bistable e-paper displays are the most appropriate display technology for IoT systems as they show as well information after a power failure or power switch off during maintenance or e.g. QR codes for installation. LED indicators are the most cost effective approach which has however very limited HMI capabilities.

The Jupiter-Io connection - An Alfven engine in space

NASA Technical Reports Server (NTRS)

Belcher, John W.

1987-01-01

Much has been learned about the electromagnetic interaction between Jupiter and its satellite Io from in situ observations. Io, in its motion through the Io plasma torus at Jupiter, continuously generates an Alfven wing that carries two billion kilowatts of power into the jovian ionosphere. Concurrently, Io is acted upon by a J x B force tending to propel it out of the jovian system. The energy source for these processes is the rotation of Jupiter. This unusual planet-satellite coupling serves as an archetype for the interaction of a large moving conductor with a magnetized plasma, a problem of general space and astrophysical interest.

The use of intraosseous infusions in the operating room.

PubMed

Joseph, Gayatri; Tobias, Joseph D

2008-09-01

The use of an intraosseous (IO) infusion during the anesthetic care of an 8-month-old, 5.4-kg infant with cyanotic congenital heart disease (CHD) is presented. Previous vascular access had resulted in thrombotic occlusion of the upper and lower venous systems. When intravenous access could not be achieved, an IO needle was placed and IO access was used during the surgical procedure. The role of the IO route in the perioperative period is discussed and its adverse effect profile is reviewed.

SCORPIO: A Scalable Two-Phase Parallel I/O Library With Application To A Large Scale Subsurface Simulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sreepathi, Sarat; Sripathi, Vamsi; Mills, Richard T

2013-01-01

Inefficient parallel I/O is known to be a major bottleneck among scientific applications employed on supercomputers as the number of processor cores grows into the thousands. Our prior experience indicated that parallel I/O libraries such as HDF5 that rely on MPI-IO do not scale well beyond 10K processor cores, especially on parallel file systems (like Lustre) with single point of resource contention. Our previous optimization efforts for a massively parallel multi-phase and multi-component subsurface simulator (PFLOTRAN) led to a two-phase I/O approach at the application level where a set of designated processes participate in the I/O process by splitting themore » I/O operation into a communication phase and a disk I/O phase. The designated I/O processes are created by splitting the MPI global communicator into multiple sub-communicators. The root process in each sub-communicator is responsible for performing the I/O operations for the entire group and then distributing the data to rest of the group. This approach resulted in over 25X speedup in HDF I/O read performance and 3X speedup in write performance for PFLOTRAN at over 100K processor cores on the ORNL Jaguar supercomputer. This research describes the design and development of a general purpose parallel I/O library, SCORPIO (SCalable block-ORiented Parallel I/O) that incorporates our optimized two-phase I/O approach. The library provides a simplified higher level abstraction to the user, sitting atop existing parallel I/O libraries (such as HDF5) and implements optimized I/O access patterns that can scale on larger number of processors. Performance results with standard benchmark problems and PFLOTRAN indicate that our library is able to maintain the same speedups as before with the added flexibility of being applicable to a wider range of I/O intensive applications.« less

Teaching Management System with Applications of RFID and IoT Technology

ERIC Educational Resources Information Center

Tan, Ping; Wu, Han; Li, Peng; Xu, He

2018-01-01

Currently, Internet of Things (IoT) technologies are used in many areas, such as intelligent transportation, smart city, hospital, games, education. Earlier interactive response system uses infrared or radio frequency (RF) wireless communication technologies to transmit the students' answer to teachers' management system, where there exists high…

Provably Secure Heterogeneous Access Control Scheme for Wireless Body Area Network.

PubMed

Omala, Anyembe Andrew; Mbandu, Angolo Shem; Mutiria, Kamenyi Domenic; Jin, Chunhua; Li, Fagen

2018-04-28

Wireless body area network (WBAN) provides a medium through which physiological information could be harvested and transmitted to application provider (AP) in real time. Integrating WBAN in a heterogeneous Internet of Things (IoT) ecosystem would enable an AP to monitor patients from anywhere and at anytime. However, the IoT roadmap of interconnected 'Things' is still faced with many challenges. One of the challenges in healthcare is security and privacy of streamed medical data from heterogeneously networked devices. In this paper, we first propose a heterogeneous signcryption scheme where a sender is in a certificateless cryptographic (CLC) environment while a receiver is in identity-based cryptographic (IBC) environment. We then use this scheme to design a heterogeneous access control protocol. Formal security proof for indistinguishability against adaptive chosen ciphertext attack and unforgeability against adaptive chosen message attack in random oracle model is presented. In comparison with some of the existing access control schemes, our scheme has lower computation and communication cost.

Data threats analysis and prevention on iOS platform

NASA Astrophysics Data System (ADS)

Gao, Bo; Wang, Yi; Chen, Zhou; Tang, Jiqiang

2015-12-01

Background: The rapid growth of mobile internet has driven the rapid popularity of smart mobiles. iOS device is chosen by more and more people for its humanity, stability and excellent industrial design, and the data security problem that followed it has gradually attracted the researchers' attention. Method & Result: This thesis focuses on the analysis of current situation of data security on iOS platform, from both security mechanism and data risk, and proposes countermeasures. Conclusion: From practical work, many problems of data security mechanism on iOS platform still exist. At present, the problem of malicious software towards iOS system has not been severe, but how to ensure the security of data on iOS platform will inevitably become one of the directions for our further study.

Jupiter's Hot, Mushy Moon

NASA Technical Reports Server (NTRS)

Taylor, G. Jeffrey

2003-01-01

Jupiter's moon Io is the most volcanically active body in the Solar System. Observations by instruments on the Galileo spacecraft and on telescopes atop Mauna Kea in Hawai'i indicate that lava flows on Io are surprisingly hot, over 1200 oC and possibly as much as 1300 oC; a few areas might have lava flows as hot as 1500 oC. Such high temperatures imply that the lava flows are composed of rock that formed by a very large amount of melting of Io's mantle. This has led Laszlo Keszthelyi and Alfred S. McEwen of the University of Arizona and me to reawaken an old hypothesis that suggests that the interior of Io is a partially-molten mush of crystals and magma. The idea, which had fallen out of favor for a decade or two, explains high-temperature hot spots, mountains, calderas, and volcanic plains on Io. If correct, Io gives us an opportunity to study processes that operate in huge, global magma systems, which scientists believe were important during the early history of the Moon and Earth, and possibly other planetary bodies as well. Though far from proven, the idea that Io has a ocean of mushy magma beneath its crust can be tested with measurements by future spacecraft.

IoT-Based User-Driven Service Modeling Environment for a Smart Space Management System

PubMed Central

Choi, Hoan-Suk; Rhee, Woo-Seop

2014-01-01

The existing Internet environment has been extended to the Internet of Things (IoT) as an emerging new paradigm. The IoT connects various physical entities. These entities have communication capability and deploy the observed information to various service areas such as building management, energy-saving systems, surveillance services, and smart homes. These services are designed and developed by professional service providers. Moreover, users' needs have become more complicated and personalized with the spread of user-participation services such as social media and blogging. Therefore, some active users want to create their own services to satisfy their needs, but the existing IoT service-creation environment is difficult for the non-technical user because it requires a programming capability to create a service. To solve this problem, we propose the IoT-based user-driven service modeling environment to provide an easy way to create IoT services. Also, the proposed environment deploys the defined service to another user. Through the personalization and customization of the defined service, the value and dissemination of the service is increased. This environment also provides the ontology-based context-information processing that produces and describes the context information for the IoT-based user-driven service. PMID:25420153

IoT-based user-driven service modeling environment for a smart space management system.

PubMed

Choi, Hoan-Suk; Rhee, Woo-Seop

2014-11-20

The existing Internet environment has been extended to the Internet of Things (IoT) as an emerging new paradigm. The IoT connects various physical entities. These entities have communication capability and deploy the observed information to various service areas such as building management, energy-saving systems, surveillance services, and smart homes. These services are designed and developed by professional service providers. Moreover, users' needs have become more complicated and personalized with the spread of user-participation services such as social media and blogging. Therefore, some active users want to create their own services to satisfy their needs, but the existing IoT service-creation environment is difficult for the non-technical user because it requires a programming capability to create a service. To solve this problem, we propose the IoT-based user-driven service modeling environment to provide an easy way to create IoT services. Also, the proposed environment deploys the defined service to another user. Through the personalization and customization of the defined service, the value and dissemination of the service is increased. This environment also provides the ontology-based context-information processing that produces and describes the context information for the IoT-based user-driven service.

Deploying Server-side File System Monitoring at NERSC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uselton, Andrew

2009-05-01

The Franklin Cray XT4 at the NERSC center was equipped with the server-side I/O monitoring infrastructure Cerebro/LMT, which is described here in detail. Insights gained from the data produced include a better understanding of instantaneous data rates during file system testing, file system behavior during regular production time, and long-term average behaviors. Information and insights gleaned from this monitoring support efforts to proactively manage the I/O infrastructure on Franklin. A simple model for I/O transactions is introduced and compared with the 250 million observations sent to the LMT database from August 2008 to February 2009.

Modeling IoT-Based Solutions Using Human-Centric Wireless Sensor Networks

PubMed Central

Monares, Álvaro; Ochoa, Sergio F.; Santos, Rodrigo; Orozco, Javier; Meseguer, Roc

2014-01-01

The Internet of Things (IoT) has inspired solutions that are already available for addressing problems in various application scenarios, such as healthcare, security, emergency support and tourism. However, there is no clear approach to modeling these systems and envisioning their capabilities at the design time. Therefore, the process of designing these systems is ad hoc and its real impact is evaluated once the solution is already implemented, which is risky and expensive. This paper proposes a modeling approach that uses human-centric wireless sensor networks to specify and evaluate models of IoT-based systems at the time of design, avoiding the need to spend time and effort on early implementations of immature designs. It allows designers to focus on the system design, leaving the implementation decisions for a next phase. The article illustrates the usefulness of this proposal through a running example, showing the design of an IoT-based solution to support the first responses during medium-sized or large urban incidents. The case study used in the proposal evaluation is based on a real train crash. The proposed modeling approach can be used to design IoT-based systems for other application scenarios, e.g., to support security operatives or monitor chronic patients in their homes. PMID:25157549

Modeling IoT-based solutions using human-centric wireless sensor networks.

PubMed

Monares, Álvaro; Ochoa, Sergio F; Santos, Rodrigo; Orozco, Javier; Meseguer, Roc

2014-08-25

The Internet of Things (IoT) has inspired solutions that are already available for addressing problems in various application scenarios, such as healthcare, security, emergency support and tourism. However, there is no clear approach to modeling these systems and envisioning their capabilities at the design time. Therefore, the process of designing these systems is ad hoc and its real impact is evaluated once the solution is already implemented, which is risky and expensive. This paper proposes a modeling approach that uses human-centric wireless sensor networks to specify and evaluate models of IoT-based systems at the time of design, avoiding the need to spend time and effort on early implementations of immature designs. It allows designers to focus on the system design, leaving the implementation decisions for a next phase. The article illustrates the usefulness of this proposal through a running example, showing the design of an IoT-based solution to support the first responses during medium-sized or large urban incidents. The case study used in the proposal evaluation is based on a real train crash. The proposed modeling approach can be used to design IoT-based systems for other application scenarios, e.g., to support security operatives or monitor chronic patients in their homes.

File-System Workload on a Scientific Multiprocessor

NASA Technical Reports Server (NTRS)

Kotz, David; Nieuwejaar, Nils

1995-01-01

Many scientific applications have intense computational and I/O requirements. Although multiprocessors have permitted astounding increases in computational performance, the formidable I/O needs of these applications cannot be met by current multiprocessors a their I/O subsystems. To prevent I/O subsystems from forever bottlenecking multiprocessors and limiting the range of feasible applications, new I/O subsystems must be designed. The successful design of computer systems (both hardware and software) depends on a thorough understanding of their intended use. A system designer optimizes the policies and mechanisms for the cases expected to most common in the user's workload. In the case of multiprocessor file systems, however, designers have been forced to build file systems based only on speculation about how they would be used, extrapolating from file-system characterizations of general-purpose workloads on uniprocessor and distributed systems or scientific workloads on vector supercomputers (see sidebar on related work). To help these system designers, in June 1993 we began the Charisma Project, so named because the project sought to characterize 1/0 in scientific multiprocessor applications from a variety of production parallel computing platforms and sites. The Charisma project is unique in recording individual read and write requests-in live, multiprogramming, parallel workloads (rather than from selected or nonparallel applications). In this article, we present the first results from the project: a characterization of the file-system workload an iPSC/860 multiprocessor running production, parallel scientific applications at NASA's Ames Research Center.

Receptor-Targeted Nanoparticles for In Vivo Imaging of Breast Cancer

PubMed Central

Yang, Lily; Peng, Xiang-Hong; Wang, Y. Andrew; Wang, Xiaoxia; Cao, Zehong; Ni, Chunchun; Karna, Prasanthi; Zhang, Xinjian; Wood, William C.; Gao, Xiaohu; Nie, Shuming; Mao, Hui

2009-01-01

Purpose Cell surface receptor-targeted magnetic iron oxide (IO) nanoparticles provide molecular magnetic resonance imaging (MRI) contrast agents for improving specificity of the detection of human cancer. Experimental design The present study reports the development of a novel targeted IO nanoparticle using a recombinant peptide containing the amino-terminal fragment (ATF) of urokinase plasminogen activator conjugated to IO nanoparticles (ATF-IO). This nanoparticle targets urokinase plasminogen activator receptor (uPAR), which is overexpressed in breast cancer tissues. Results ATF-IO nanoparticles are able to specifically bind to and be internalized by uPAR-expressing tumor cells. Systemic delivery of ATF-IO nanoparticles into mice bearing subcutaneous and intraperitoneal mammary tumors leads to the accumulation of the particles in tumors, generating a strong MRI contrast detectable by a clinical MRI scanner at a field strength of 3 Tesla. Target specificity of ATF-IO nanoparticles demonstrated by in vivo MRI is further confirmed by near infrared (NIR) fluorescence imaging of the mammary tumors using NIR dye-labeled ATF peptides conjugated to IO nanoparticles. Furthermore, mice administered ATF-IO nanoparticles exhibit lower uptake of the particles in the liver and spleen compared to those receiving non-targeted IO nanoparticles. Conclusions Our results suggest that uPAR-targeted ATF-IO nanoparticles have potential as molecularly-targeted, dual modality imaging agents for in vivo imaging of breast cancer. PMID:19584158

Io’s volcanoes at high spatial, spectral, and temporal resolution from ground-based observations

NASA Astrophysics Data System (ADS)

de Kleer, Katherine R.; de Pater, Imke

2017-10-01

Io’s dynamic volcanic eruptions provide a laboratory for studying large-scale volcanism on a body vastly different from Earth, and for unraveling the connections between tidal heating and the geological activity it powers. Ground-based near-infrared observatories allow for high-cadence, long-time-baseline observing programs using diverse instrumentation, and yield new information into the nature and variability of this activity. I will summarize results from four years of ground-based observations of Io’s volcanism, including: (1) A multi-year cadence observing campaign using adaptive optics on 8-10 meter telescopes, which places constraints on tidal heating models through sampling the spatial distribution of Io’s volcanic heat flow, and provides estimates of the occurrence rate of Io’s most energetic eruptions; (2) High-spectral-resolution (R~25,000) studies of Io’s volcanic SO gas emission at 1.7 microns, which resolves this rovibronic line into its different branches, and thus contains detailed information on the temperature and thermal state of the gas; and (3) The highest-spatial-resolution map ever produced of the entire Loki Patera, a 20,000 km2 volcanic feature on Io, derived from adaptive-optics observations of an occultation of Io by Europa. The map achieves a spatial resolution of ~10 km and indicates compositional differences across the patera. These datasets both reveal specific characteristics of Io’s individual eruptions, and provide clues into the sub-surface systems connecting Io’s tidally-heated interior to its surface expressions of volcanism.

FIRE - Flyby of Io with Repeat Encounters: A conceptual design for a New Frontiers mission to Io

NASA Astrophysics Data System (ADS)

Suer, Terry-Ann; Padovan, Sebastiano; Whitten, Jennifer L.; Potter, Ross W. K.; Shkolyar, Svetlana; Cable, Morgan; Walker, Catherine; Szalay, Jamey; Parker, Charles; Cumbers, John; Gentry, Diana; Harrison, Tanya; Naidu, Shantanu; Trammell, Harold J.; Reimuller, Jason; Budney, Charles J.; Lowes, Leslie L.

2017-09-01

A conceptual design is presented for a low complexity, heritage-based flyby mission to Io, Jupiter's innermost Galilean satellite and the most volcanically active body in the Solar System. The design addresses the 2011 Decadal Survey's recommendation for a New Frontiers class mission to Io and is based upon the result of the June 2012 NASA-JPL Planetary Science Summer School. A science payload is proposed to investigate the link between the structure of Io's interior, its volcanic activity, its surface composition, and its tectonics. A study of Io's atmospheric processes and Io's role in the Jovian magnetosphere is also planned. The instrument suite includes a visible/near-IR imager, a magnetic field and plasma suite, a dust analyzer, and a gimbaled high gain antenna to perform radio science. Payload activity and spacecraft operations would be powered by three Advanced Stirling Radioisotope Generators (ASRG). The primary mission includes 10 flybys with close-encounter altitudes as low as 100 km. The mission risks are mitigated by ensuring that relevant components are radiation tolerant and by using redundancy and flight-proven parts in the design. The spacecraft would be launched on an Atlas V rocket with a delta-v of 1.3 km/s. Three gravity assists (Venus, Earth, Earth) would be used to reach the Jupiter system in a 6-year cruise. The resulting concept demonstrates the rich scientific return of a flyby mission to Io.

Examining the accuracy of the infinite order sudden approximation using sensitivity analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eno, L.; Rabitz, H.

1981-08-15

A method is developed for assessing the accuracy of scattering observables calculated within the framework of the infinite order sudden (IOS) approximation. In particular, we focus on the energy sudden assumption of the IOS method and our approach involves the determination of the sensitivity of the IOS scattering matrix S/sup IOS/ with respect to a parameter which reintroduces the internal energy operator h/sub 0/ into the IOS Hamiltonian. This procedure is an example of sensitivity analysis of missing model components (h/sub 0/ in this case) in the reference Hamiltonian. In contrast to simple first-order perturbation theory a finite result ismore » obtained for the effect of h/sub 0/ on S/sup IOS/. As an illustration, our method of analysis is applied to integral state-to-state cross sections for the scattering of an atom and rigid rotor. Results are generated within the He+H/sub 2/ system and a comparison is made between IOS and coupled states cross sections and the corresponding IOS sensitivities. It is found that the sensitivity coefficients are very useful indicators of the accuracy of the IOS results. Finally, further developments and applications are discussed.« less

MinT: Middleware for Cooperative Interaction of Things

PubMed Central

Jeon, Soobin; Jung, Inbum

2017-01-01

This paper proposes an Internet of Things (IoT) middleware called Middleware for Cooperative Interaction of Things (MinT). MinT supports a fully distributed IoT environment in which IoT devices directly connect to peripheral devices easily construct a local or global network, and share their data in an energy efficient manner. MinT provides a sensor abstract layer, a system layer and an interaction layer. These enable integrated sensing device operations, efficient resource management, and active interconnection between peripheral IoT devices. In addition, MinT provides a high-level API to develop IoT devices easily for IoT device developers. We aim to enhance the energy efficiency and performance of IoT devices through the performance improvements offered by MinT resource management and request processing. The experimental results show that the average request rate increased by 25% compared to Californium, which is a middleware for efficient interaction in IoT environments with powerful performance, an average response time decrease of 90% when resource management was used, and power consumption decreased by up to 68%. Finally, the proposed platform can reduce the latency and power consumption of IoT devices. PMID:28632182

MinT: Middleware for Cooperative Interaction of Things.

PubMed

Jeon, Soobin; Jung, Inbum

2017-06-20

This paper proposes an Internet of Things (IoT) middleware called Middleware for Cooperative Interaction of Things (MinT). MinT supports a fully distributed IoT environment in which IoT devices directly connect to peripheral devices easily construct a local or global network, and share their data in an energy efficient manner. MinT provides a sensor abstract layer, a system layer and an interaction layer. These enable integrated sensing device operations, efficient resource management, and active interconnection between peripheral IoT devices. In addition, MinT provides a high-level API to develop IoT devices easily for IoT device developers. We aim to enhance the energy efficiency and performance of IoT devices through the performance improvements offered by MinT resource management and request processing. The experimental results show that the average request rate increased by 25% compared to Californium, which is a middleware for efficient interaction in IoT environments with powerful performance, an average response time decrease of 90% when resource management was used, and power consumption decreased by up to 68%. Finally, the proposed platform can reduce the latency and power consumption of IoT devices.

An Energy-Efficient Compressive Image Coding for Green Internet of Things (IoT).

PubMed

Li, Ran; Duan, Xiaomeng; Li, Xu; He, Wei; Li, Yanling

2018-04-17

Aimed at a low-energy consumption of Green Internet of Things (IoT), this paper presents an energy-efficient compressive image coding scheme, which provides compressive encoder and real-time decoder according to Compressive Sensing (CS) theory. The compressive encoder adaptively measures each image block based on the block-based gradient field, which models the distribution of block sparse degree, and the real-time decoder linearly reconstructs each image block through a projection matrix, which is learned by Minimum Mean Square Error (MMSE) criterion. Both the encoder and decoder have a low computational complexity, so that they only consume a small amount of energy. Experimental results show that the proposed scheme not only has a low encoding and decoding complexity when compared with traditional methods, but it also provides good objective and subjective reconstruction qualities. In particular, it presents better time-distortion performance than JPEG. Therefore, the proposed compressive image coding is a potential energy-efficient scheme for Green IoT.

Mobile Edge Computing Empowers Internet of Things

NASA Astrophysics Data System (ADS)

Ansari, Nirwan; Sun, Xiang

In this paper, we propose a Mobile Edge Internet of Things (MEIoT) architecture by leveraging the fiber-wireless access technology, the cloudlet concept, and the software defined networking framework. The MEIoT architecture brings computing and storage resources close to Internet of Things (IoT) devices in order to speed up IoT data sharing and analytics. Specifically, the IoT devices (belonging to the same user) are associated to a specific proxy Virtual Machine (VM) in the nearby cloudlet. The proxy VM stores and analyzes the IoT data (generated by its IoT devices) in real-time. Moreover, we introduce the semantic and social IoT technology in the context of MEIoT to solve the interoperability and inefficient access control problem in the IoT system. In addition, we propose two dynamic proxy VM migration methods to minimize the end-to-end delay between proxy VMs and their IoT devices and to minimize the total on-grid energy consumption of the cloudlets, respectively. Performance of the proposed methods are validated via extensive simulations.

Disturbances of Higher Level Neural Control-Robotic Applications in Stroke

DTIC Science & Technology

2001-10-25

Interim Results on the Follow-up of 76 Patients and on Movement Performance Indices, In: Mounir Mokhtari (ed); Integration of Assistive Technology in the...the Nervous System’s Adaptive Mechanisms, In: Mounir Mokhtari (ed); Integration of Assistive Technology in the Information Age; IOS Press, Assistive

A highly reliable, autonomous data communication subsystem for an advanced information processing system

NASA Technical Reports Server (NTRS)

Nagle, Gail; Masotto, Thomas; Alger, Linda

1990-01-01

The need to meet the stringent performance and reliability requirements of advanced avionics systems has frequently led to implementations which are tailored to a specific application and are therefore difficult to modify or extend. Furthermore, many integrated flight critical systems are input/output intensive. By using a design methodology which customizes the input/output mechanism for each new application, the cost of implementing new systems becomes prohibitively expensive. One solution to this dilemma is to design computer systems and input/output subsystems which are general purpose, but which can be easily configured to support the needs of a specific application. The Advanced Information Processing System (AIPS), currently under development has these characteristics. The design and implementation of the prototype I/O communication system for AIPS is described. AIPS addresses reliability issues related to data communications by the use of reconfigurable I/O networks. When a fault or damage event occurs, communication is restored to functioning parts of the network and the failed or damage components are isolated. Performance issues are addressed by using a parallelized computer architecture which decouples Input/Output (I/O) redundancy management and I/O processing from the computational stream of an application. The autonomous nature of the system derives from the highly automated and independent manner in which I/O transactions are conducted for the application as well as from the fact that the hardware redundancy management is entirely transparent to the application.

Security Techniques for Sensor Systems and the Internet of Things

ERIC Educational Resources Information Center

Midi, Daniele

2016-01-01

Sensor systems are becoming pervasive in many domains, and are recently being generalized by the Internet of Things (IoT). This wide deployment, however, presents significant security issues. We develop security techniques for sensor systems and IoT, addressing all security management phases. Prior to deployment, the nodes need to be hardened. We…

Classification of Volcanic Eruptions on Io and Earth Using Low-Resolution Remote Sensing Data

NASA Technical Reports Server (NTRS)

Davies, A. G.; Keszthelyi, L. P.

2005-01-01

Two bodies in the Solar System exhibit high-temperature active volcanism: Earth and Io. While there are important differences in the eruptions on Earth and Io, in low-spatial-resolution data (corresponding to the bulk of available and foreseeable data of Io), similar styles of effusive and explosive volcanism yield similar thermal flux densities. For example, a square metre of an active pahoehoe flow on Io looks very similar to a square metre of an active pahoehoe flow on Earth. If, from observed thermal emission as a function of wavelength and change in thermal emission with time, the eruption style of an ionian volcano can be constrained, estimates of volumetric fluxes can be made and compared with terrestrial volcanoes using techniques derived for analysing terrestrial remotely-sensed data. In this way we find that ionian volcanoes fundamentally differ from their terrestrial counterparts only in areal extent, with Io volcanoes covering larger areas, with higher volumetric flux. Io outbursts eruptions have enormous implied volumetric fluxes, and may scale with terrestrial flood basalt eruptions. Even with the low-spatial resolution data available it is possible to sometimes constrain and classify eruption style both on Io and Earth from the integrated thermal emission spectrum. Plotting 2 and 5 m fluxes reveals the evolution of individual eruptions of different styles, as well as the relative intensity of eruptions, allowing comparison to be made from individual eruptions on both planets. Analyses like this can be used for interpretation of low-resolution data until the next mission to the jovian system. For a number of Io volcanoes (including Pele, Prometheus, Amirani, Zamama, Culann, Tohil and Tvashtar) we do have high/moderate resolution imagery to aid determination of eruption mode from analyses based only on low spatial-resolution data.

The Index of Vulnerability: An anthropological method linking social-ecological systems to mental and physical health outcomes.

PubMed

Tallman, Paula Skye

2016-08-01

Researchers need measures of vulnerability that are grounded in explicit theoretical and conceptual frameworks, that are sensitive to local contexts, and that are easy to collect. This paper presents the Index of Vulnerability (IoV), a quantitative yet anthropologically-informed method connecting social-ecological systems to mental and physical health outcomes. The IoV combines measures of five life domains; food insecurity, water insecurity, access to healthcare, social support, and social status. Scores on this index increase for each life domain where the individual falls into a "high risk" category. Thus, individuals with the highest IoV scores are those who are at risk across multiple life domains. This approach makes the IoV malleable to local contexts, as scholars can choose which measure of each life domain is most appropriate for their study population. An anthropological study conducted among 225 Awajún adults living in the Peruvian Amazon from March to November of 2013 showed that men with higher IoV scores had significantly lower summary fat skinfolds, lower triglyceride levels, and a greater probability of reporting moderate to severe somatic symptoms and poor perceived health. Awajún women with higher IoV scores had significantly elevated perceived stress levels and a greater probability of reporting poor perceived health and moderate to severe somatic and depressive symptoms. Importantly, comparing the IoV to its constituent parts shows that it predicts a wider range of mental and physical health outcomes than any of the life domains alone. The IoV is presented here in relation to the broader political-economic and cultural context of the Awajún, forwarding a critical biocultural approach within anthropology, and demonstrating the IoV's utility for other scholars and practitioners. Copyright © 2016 Elsevier Ltd. All rights reserved.

A real-time spiking cerebellum model for learning robot control.

PubMed

Carrillo, Richard R; Ros, Eduardo; Boucheny, Christian; Coenen, Olivier J-M D

2008-01-01

We describe a neural network model of the cerebellum based on integrate-and-fire spiking neurons with conductance-based synapses. The neuron characteristics are derived from our earlier detailed models of the different cerebellar neurons. We tested the cerebellum model in a real-time control application with a robotic platform. Delays were introduced in the different sensorimotor pathways according to the biological system. The main plasticity in the cerebellar model is a spike-timing dependent plasticity (STDP) at the parallel fiber to Purkinje cell connections. This STDP is driven by the inferior olive (IO) activity, which encodes an error signal using a novel probabilistic low frequency model. We demonstrate the cerebellar model in a robot control system using a target-reaching task. We test whether the system learns to reach different target positions in a non-destructive way, therefore abstracting a general dynamics model. To test the system's ability to self-adapt to different dynamical situations, we present results obtained after changing the dynamics of the robotic platform significantly (its friction and load). The experimental results show that the cerebellar-based system is able to adapt dynamically to different contexts.

mIoT Slice for 5G Systems: Design and Performance Evaluation

PubMed Central

Condoluci, Massimo; An, Xueli

2018-01-01

Network slicing is a key feature of the upcoming 5G networks allowing the design and deployment of customized communication systems to integrate services provided by vertical industries. In this context, massive Internet of Things (mIoT) is regarded as a compelling use case, both for its relevance from business perspective, and for the technical challenges it poses to network design. With their envisaged massive deployment of devices requiring sporadic connectivity and small data transmission, yet Quality of Service (QoS) constrained, mIoT services will need an ad-hoc end-to-end (E2E) slice, i.e., both access and core network with enhanced Control and User planes (CP/UP). After revising the key requirements of mIoT and identifying major shortcomings of previous generation networks, this paper presents and evaluates an E2E mIoT network slicing solution, featuring a new connectivity model overcoming the load limitations of legacy systems. Unique in its kind, this paper addresses mIoT requirements from an end-to-end perspective highlighting and solving, unlike most prior related work, the connectivity challenges posed to the core network. Results demonstrate that the proposed solution, reducing CP signaling and optimizing UP resource utilization, is a suitable candidate for next generation network standards to efficiently handle massive device deployment. PMID:29466311

mIoT Slice for 5G Systems: Design and Performance Evaluation.

PubMed

Trivisonno, Riccardo; Condoluci, Massimo; An, Xueli; Mahmoodi, Toktam

2018-02-21

Network slicing is a key feature of the upcoming 5G networks allowing the design and deployment of customized communication systems to integrate services provided by vertical industries. In this context, massive Internet of Things (mIoT) is regarded as a compelling use case, both for its relevance from business perspective, and for the technical challenges it poses to network design. With their envisaged massive deployment of devices requiring sporadic connectivity and small data transmission, yet Quality of Service (QoS) constrained, mIoT services will need an ad-hoc end-to-end (E2E) slice, i.e., both access and core network with enhanced Control and User planes (CP/UP). After revising the key requirements of mIoT and identifying major shortcomings of previous generation networks, this paper presents and evaluates an E2E mIoT network slicing solution, featuring a new connectivity model overcoming the load limitations of legacy systems. Unique in its kind, this paper addresses mIoT requirements from an end-to-end perspective highlighting and solving, unlike most prior related work, the connectivity challenges posed to the core network. Results demonstrate that the proposed solution, reducing CP signaling and optimizing UP resource utilization, is a suitable candidate for next generation network standards to efficiently handle massive device deployment.

A comparative evaluation of pain and anxiety levels in 2 different anesthesia techniques: locoregional anesthesia using conventional syringe versus intraosseous anesthesia using a computer-controlled system (Quicksleeper).

PubMed

Özer, Senem; Yaltirik, Mehmet; Kirli, Irem; Yargic, Ilhan

2012-11-01

The aim of this study was to compare anxiety and pain levels during anesthesia and efficacy of Quicksleeper intraosseous (IO) injection system, which delivers computer-controlled IO anesthesia and conventional inferior alveolar nerve block (IANB) in impacted mandibular third molars. Forty subjects with bilateral impacted mandibular third molars randomly received IO injection or conventional IANB at 2 successive appointments. The subjects received 1.8 mL 2% articaine. IO injection has many advantages, such as enabling painless anesthesia with less soft tissue numbness and quick onset of anesthesia as well as lingual and palatal anesthesia with single needle penetration. Although IO injection is a useful technique commonly used during various treatments in dentistry, the duration of injection takes longer than conventional techniques, there is a possibility of obstruction at the needle tip, and, the duration of the anesthetic effect is inadequate for prolonged surgical procedures. Copyright © 2012 Elsevier Inc. All rights reserved.

Exploring the use of I/O nodes for computation in a MIMD multiprocessor

NASA Technical Reports Server (NTRS)

Kotz, David; Cai, Ting

1995-01-01

As parallel systems move into the production scientific-computing world, the emphasis will be on cost-effective solutions that provide high throughput for a mix of applications. Cost effective solutions demand that a system make effective use of all of its resources. Many MIMD multiprocessors today, however, distinguish between 'compute' and 'I/O' nodes, the latter having attached disks and being dedicated to running the file-system server. This static division of responsibilities simplifies system management but does not necessarily lead to the best performance in workloads that need a different balance of computation and I/O. Of course, computational processes sharing a node with a file-system service may receive less CPU time, network bandwidth, and memory bandwidth than they would on a computation-only node. In this paper we begin to examine this issue experimentally. We found that high performance I/O does not necessarily require substantial CPU time, leaving plenty of time for application computation. There were some complex file-system requests, however, which left little CPU time available to the application. (The impact on network and memory bandwidth still needs to be determined.) For applications (or users) that cannot tolerate an occasional interruption, we recommend that they continue to use only compute nodes. For tolerant applications needing more cycles than those provided by the compute nodes, we recommend that they take full advantage of both compute and I/O nodes for computation, and that operating systems should make this possible.

Coalitions of things: supporting ISR tasks via internet of things approaches

NASA Astrophysics Data System (ADS)

Preece, Alun; Taylor, Ian; Dawson, Andrew; Braines, Dave; O'Leary, Nick; Thomas, Anna; Tomsett, Richard; La Porta, Tom; Bakdash, Jonathan Z.; Zaroukian, Erin

2017-05-01

In the wake of rapid maturing of Internet of Things (IoT) approaches and technologies in the commercial sector, the IoT is increasingly seen as a key `disruptive' technology in military environments. Future operational environments are expected to be characterized by a lower proportion of human participants and a higher proportion of autonomous and semi-autonomous devices. This view is reflected in both US `third offset' and UK `information age' thinking and is likely to have a profound effect on how multinational coalition operations are conducted in the future. Much of the initial consideration of IoT adoption in the military domain has rightly focused on security concerns, reflecting similar cautions in the early era of electronic commerce. As IoT approaches mature, this initial technical focus is likely to shift to considerations of interactivity and policy. In this paper, rather than considering the broader range of IoT applications in the military context, we focus on roles for IoT concepts and devices in future intelligence, surveillance and reconnaissance (ISR) tasks, drawing on experience in sensor-mission resourcing and human-computer collaboration (HCC) for ISR. We highlight the importance of low training overheads in the adoption of IoT approaches, and the need to balance proactivity and interactivity (push vs pull modes). As with sensing systems over the last decade, we emphasize that, to be valuable in ISR tasks, IoT devices will need a degree of mission-awareness in addition to an ability to self-manage their limited resources (power, memory, bandwidth, computation, etc). In coalition operations, the management and potential sharing of IoT devices and systems among partners (e.g., in cross-coalition tactical-edge ISR teams) becomes a key issue due heterogeneous factors such as language, policy, procedure and doctrine. Finally, we briefly outline a platform that we have developed in order to experiment with human-IoT teaming on ISR tasks, in both physical and virtual settings.

Adopting Industry Standards for Control Systems Within Advanced Life Support

NASA Technical Reports Server (NTRS)

Young, James Scott; Boulanger, Richard

2002-01-01

This paper gives a description of OPC (Object Linking and Embedding for Process Control) standards for process control and outlines the experiences at JSC with using these standards to interface with I/O hardware from three independent vendors. The I/O hardware was integrated with a commercially available SCADA/HMI software package to make up the control and monitoring system for the Environmental Systems Test Stand (ESTS). OPC standards were utilized for communicating with I/O hardware and the software was used for implementing monitoring, PC-based distributed control, and redundant data storage over an Ethernet physical layer using an embedded din-rail mounted PC.

Time variability of Io's volcanic activity from near-IR adaptive optics observations on 100 nights in 2013-2015

NASA Astrophysics Data System (ADS)

de Kleer, Katherine; de Pater, Imke

2016-12-01

Jupiter's moon Io is a dynamic target, exhibiting extreme and time-variable volcanic activity powered by tidal forcing from Jupiter. We have conducted a campaign of high-cadence observations of Io with the goal of characterizing its volcanic activity. Between Aug 2013 and the end of 2015, we imaged Io on 100 nights in the near-infrared with adaptive optics on the Keck and Gemini N telescopes, which resolve emission from individual volcanic hot spots. During our program, we made over 400 detections of 48 distinct hot spots, some of which were detected 30+ times. We use these observations to derive a timeline of global volcanic activity on Io, which exhibits wide variability from month to month. The timelines of thermal activity at individual volcanic centers have geophysical implications, and will permit future characterization by others. We evaluate hot spot detection limits and give a simple parameterization of the minimum detectable intensity as a function of emission angle, which can be applied to other analyses. We detected three outburst eruptions in August 2013, but no other outburst-scale events were observed in the subsequent ∼90 observations. Either the cluster of events in August 2013 was a rare occurrence, or there is a mechanism causing large events to occur closely-spaced in time. We also detected large eruptions (though not of outburst scale) within days of one another at Kurdalagon Patera and Sethlaus/Gabija Paterae in 2015. As was also seen in the Galileo dataset, the hot spots we detected can be separated into two categories based on their thermal emission: those that are persistently active for 1 year or more at moderate intensity, and those that are only briefly active, are time-variable, and often reach large intensities. A small number of hot spots in the latter category appear and subside in a matter of days, reaching particularly high intensities; although these are not bright enough to qualify as outbursts, their thermal signatures follow the same pattern, suggesting that a similar mechanism may be responsible for these events though at a smaller scale. Two eruptions seen at Kurdalagon Patera in January and April 2015 occurred simultaneously with a brightening of the neutral cloud and plasma torus which are sourced from Io's atmosphere. A plume at Kurdalagon Patera, such as was seen by New Horizons in 2007, could have been responsible for the influx of material that caused these brightenings.

A Proposal for IoT Dynamic Routes Selection Based on Contextual Information.

PubMed

Araújo, Harilton da Silva; Filho, Raimir Holanda; Rodrigues, Joel J P C; Rabelo, Ricardo de A L; Sousa, Natanael de C; Filho, José C C L S; Sobral, José V V

2018-01-26

The Internet of Things (IoT) is based on interconnection of intelligent and addressable devices, allowing their autonomy and proactive behavior with Internet connectivity. Data dissemination in IoT usually depends on the application and requires context-aware routing protocols that must include auto-configuration features (which adapt the behavior of the network at runtime, based on context information). This paper proposes an approach for IoT route selection using fuzzy logic in order to attain the requirements of specific applications. In this case, fuzzy logic is used to translate in math terms the imprecise information expressed by a set of linguistic rules. For this purpose, four Objective Functions (OFs) are proposed for the Routing Protocol for Low Power and Loss Networks (RPL); such OFs are dynamically selected based on context information. The aforementioned OFs are generated from the fusion of the following metrics: Expected Transmission Count (ETX), Number of Hops (NH) and Energy Consumed (EC). The experiments performed through simulation, associated with the statistical data analysis, conclude that this proposal provides high reliability by successfully delivering nearly 100% of data packets, low delay for data delivery and increase in QoS. In addition, an 30% improvement is attained in the network life time when using one of proposed objective function, keeping the devices alive for longer duration.

Robust High-dimensional Bioinformatics Data Streams Mining by ODR-ioVFDT

PubMed Central

Wang, Dantong; Fong, Simon; Wong, Raymond K.; Mohammed, Sabah; Fiaidhi, Jinan; Wong, Kelvin K. L.

2017-01-01

Outlier detection in bioinformatics data streaming mining has received significant attention by research communities in recent years. The problems of how to distinguish noise from an exception and deciding whether to discard it or to devise an extra decision path for accommodating it are causing dilemma. In this paper, we propose a novel algorithm called ODR with incrementally Optimized Very Fast Decision Tree (ODR-ioVFDT) for taking care of outliers in the progress of continuous data learning. By using an adaptive interquartile-range based identification method, a tolerance threshold is set. It is then used to judge if a data of exceptional value should be included for training or otherwise. This is different from the traditional outlier detection/removal approaches which are two separate steps in processing through the data. The proposed algorithm is tested using datasets of five bioinformatics scenarios and comparing the performance of our model and other ones without ODR. The results show that ODR-ioVFDT has better performance in classification accuracy, kappa statistics, and time consumption. The ODR-ioVFDT applied onto bioinformatics streaming data processing for detecting and quantifying the information of life phenomena, states, characters, variables and components of the organism can help to diagnose and treat disease more effectively. PMID:28230161

Toward Transparent Data Management in Multi-layer Storage Hierarchy for HPC Systems

DOE PAGES

Wadhwa, Bharti; Byna, Suren; Butt, Ali R.

2018-04-17

Upcoming exascale high performance computing (HPC) systems are expected to comprise multi-tier storage hierarchy, and thus will necessitate innovative storage and I/O mechanisms. Traditional disk and block-based interfaces and file systems face severe challenges in utilizing capabilities of storage hierarchies due to the lack of hierarchy support and semantic interfaces. Object-based and semantically-rich data abstractions for scientific data management on large scale systems offer a sustainable solution to these challenges. Such data abstractions can also simplify users involvement in data movement. Here, we take the first steps of realizing such an object abstraction and explore storage mechanisms for these objectsmore » to enhance I/O performance, especially for scientific applications. We explore how an object-based interface can facilitate next generation scalable computing systems by presenting the mapping of data I/O from two real world HPC scientific use cases: a plasma physics simulation code (VPIC) and a cosmology simulation code (HACC). Our storage model stores data objects in different physical organizations to support data movement across layers of memory/storage hierarchy. Our implementation sclaes well to 16K parallel processes, and compared to the state of the art, such as MPI-IO and HDF5, our object-based data abstractions and data placement strategy in multi-level storage hierarchy achieves up to 7 X I/O performance improvement for scientific data.« less

Toward Transparent Data Management in Multi-layer Storage Hierarchy for HPC Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wadhwa, Bharti; Byna, Suren; Butt, Ali R.

Upcoming exascale high performance computing (HPC) systems are expected to comprise multi-tier storage hierarchy, and thus will necessitate innovative storage and I/O mechanisms. Traditional disk and block-based interfaces and file systems face severe challenges in utilizing capabilities of storage hierarchies due to the lack of hierarchy support and semantic interfaces. Object-based and semantically-rich data abstractions for scientific data management on large scale systems offer a sustainable solution to these challenges. Such data abstractions can also simplify users involvement in data movement. Here, we take the first steps of realizing such an object abstraction and explore storage mechanisms for these objectsmore » to enhance I/O performance, especially for scientific applications. We explore how an object-based interface can facilitate next generation scalable computing systems by presenting the mapping of data I/O from two real world HPC scientific use cases: a plasma physics simulation code (VPIC) and a cosmology simulation code (HACC). Our storage model stores data objects in different physical organizations to support data movement across layers of memory/storage hierarchy. Our implementation sclaes well to 16K parallel processes, and compared to the state of the art, such as MPI-IO and HDF5, our object-based data abstractions and data placement strategy in multi-level storage hierarchy achieves up to 7 X I/O performance improvement for scientific data.« less

A Modular IoT Platform for Real-Time Indoor Air Quality Monitoring

PubMed Central

Abdaoui, Abderrazak; Ahmad, Sabbir H.M.; Touati, Farid; Kadri, Abdullah

2018-01-01

The impact of air quality on health and on life comfort is well established. In many societies, vulnerable elderly and young populations spend most of their time indoors. Therefore, indoor air quality monitoring (IAQM) is of great importance to human health. Engineers and researchers are increasingly focusing their efforts on the design of real-time IAQM systems using wireless sensor networks. This paper presents an end-to-end IAQM system enabling measurement of CO2, CO, SO2, NO2, O3, Cl2, ambient temperature, and relative humidity. In IAQM systems, remote users usually use a local gateway to connect wireless sensor nodes in a given monitoring site to the external world for ubiquitous access of data. In this work, the role of the gateway in processing collected air quality data and its reliable dissemination to end-users through a web-server is emphasized. A mechanism for the backup and the restoration of the collected data in the case of Internet outage is presented. The system is adapted to an open-source Internet-of-Things (IoT) web-server platform, called Emoncms, for live monitoring and long-term storage of the collected IAQM data. A modular IAQM architecture is adopted, which results in a smart scalable system that allows seamless integration of various sensing technologies, wireless sensor networks (WSNs) and smart mobile standards. The paper gives full hardware and software details of the proposed solution. Sample IAQM results collected in various locations are also presented to demonstrate the abilities of the system. PMID:29443893

An intelligent IoT emergency vehicle warning system using RFID and Wi-Fi technologies for emergency medical services.

PubMed

Lai, Yeong-Lin; Chou, Yung-Hua; Chang, Li-Chih

2018-01-01

Collisions between emergency vehicles for emergency medical services (EMS) and public road users have been a serious problem, impacting on the safety of road users, emergency medical technicians (EMTs), and the patients on board. The aim of this study is to develop a novel intelligent emergency vehicle warning system for EMS applications. The intelligent emergency vehicle warning system is developed by Internet of Things (IoT), radio-frequency identification (RFID), and Wi-Fi technologies. The system consists of three major parts: a system trigger tag, an RFID system in an emergency vehicle, and an RFID system at an intersection. The RFID system either in an emergency vehicle or at an intersection contains a controller, an ultrahigh-frequency (UHF) RFID reader module, a Wi-Fi module, and a 2.4-GHz antenna. In addition, a UHF ID antenna is especially designed for the RFID system in an emergency vehicle. The IoT system provides real-time visual warning at an intersection and siren warning from an emergency vehicle in order to effectively inform road users about an emergency vehicle approaching. The developed intelligent IoT emergency vehicle warning system demonstrates the capabilities of real-time visual and siren warnings for EMS safety.

Development of a Real Time Sparse Non-Negative Matrix Factorization Module for Cochlear Implants by Using xPC Target

PubMed Central

Hu, Hongmei; Krasoulis, Agamemnon; Lutman, Mark; Bleeck, Stefan

2013-01-01

Cochlear implants (CIS) require efficient speech processing to maximize information transmission to the brain, especially in noise. A novel CI processing strategy was proposed in our previous studies, in which sparsity-constrained non-negative matrix factorization (NMF) was applied to the envelope matrix in order to improve the CI performance in noisy environments. It showed that the algorithm needs to be adaptive, rather than fixed, in order to adjust to acoustical conditions and individual characteristics. Here, we explore the benefit of a system that allows the user to adjust the signal processing in real time according to their individual listening needs and their individual hearing capabilities. In this system, which is based on MATLAB®, SIMULINK® and the xPC Target™ environment, the input/outupt (I/O) boards are interfaced between the SIMULINK blocks and the CI stimulation system, such that the output can be controlled successfully in the manner of a hardware-in-the-loop (HIL) simulation, hence offering a convenient way to implement a real time signal processing module that does not require any low level language. The sparsity constrained parameter of the algorithm was adapted online subjectively during an experiment with normal-hearing subjects and noise vocoded speech simulation. Results show that subjects chose different parameter values according to their own intelligibility preferences, indicating that adaptive real time algorithms are beneficial to fully explore subjective preferences. We conclude that the adaptive real time systems are beneficial for the experimental design, and such systems allow one to conduct psychophysical experiments with high ecological validity. PMID:24129021

Development of a real time sparse non-negative matrix factorization module for cochlear implants by using xPC target.

PubMed

Hu, Hongmei; Krasoulis, Agamemnon; Lutman, Mark; Bleeck, Stefan

2013-10-14

Cochlear implants (CIs) require efficient speech processing to maximize information transmission to the brain, especially in noise. A novel CI processing strategy was proposed in our previous studies, in which sparsity-constrained non-negative matrix factorization (NMF) was applied to the envelope matrix in order to improve the CI performance in noisy environments. It showed that the algorithm needs to be adaptive, rather than fixed, in order to adjust to acoustical conditions and individual characteristics. Here, we explore the benefit of a system that allows the user to adjust the signal processing in real time according to their individual listening needs and their individual hearing capabilities. In this system, which is based on MATLAB®, SIMULINK® and the xPC Target™ environment, the input/outupt (I/O) boards are interfaced between the SIMULINK blocks and the CI stimulation system, such that the output can be controlled successfully in the manner of a hardware-in-the-loop (HIL) simulation, hence offering a convenient way to implement a real time signal processing module that does not require any low level language. The sparsity constrained parameter of the algorithm was adapted online subjectively during an experiment with normal-hearing subjects and noise vocoded speech simulation. Results show that subjects chose different parameter values according to their own intelligibility preferences, indicating that adaptive real time algorithms are beneficial to fully explore subjective preferences. We conclude that the adaptive real time systems are beneficial for the experimental design, and such systems allow one to conduct psychophysical experiments with high ecological validity.

Enhancing the Internet of Things Architecture with Flow Semantics

ERIC Educational Resources Information Center

DeSerranno, Allen Ronald

2017-01-01

Internet of Things ("IoT") systems are complex, asynchronous solutions often comprised of various software and hardware components developed in isolation of each other. These components function with different degrees of reliability and performance over an inherently unreliable network, the Internet. Many IoT systems are developed within…

A Generic System-Level Framework for Self-Serve Health Monitoring System through Internet of Things (IoT).

PubMed

Ahmed, Mobyen Uddin; Björkman, Mats; Lindén, Maria

2015-01-01

Sensor data are traveling from sensors to a remote server, data is analyzed remotely in a distributed manner, and health status of a user is presented in real-time. This paper presents a generic system-level framework for a self-served health monitoring system through the Internet of Things (IoT) to facilities an efficient sensor data management.

The use of intraosseous anesthesia among endodontists: results of a questionnaire.

PubMed

Bangerter, Chad; Mines, Pete; Sweet, Mark

2009-01-01

The purpose of this study was to investigate the use of supplemental intraosseous (IO) anesthesia among endodontists in the United States. The study also looked at the types of anesthetic solutions commonly used for IO anesthesia and in which diagnostic conditions IO anesthesia is used. A Web-based survey of 2,528 active members of the American Association of Endodontists was sent out by e-mail. Data from 833 respondents were collected with a response rate of 33%. It was discovered that 94.77% of the respondents used some form of IO anesthesia, with the periodontal ligament injection (PDL) being the most commonly administered (49.78%). Symptomatic irreversible pulpitis is the pulpal diagnosis for which respondents most often use some form of IO anesthesia (61.99%), and 2% lidocaine with epinephrine 1:100,000 is the most common anesthetic solution used in IO anesthesia (37.62%). Although more than half of the respondents use some form of IO anesthesia more than twice a week, newer IO anesthesia delivery systems such as Stabident (Fairfax Dental, San Francisco, CA) and X-Tip (Dentsply International, Johnson City, TN) are used less often than the PDL injection.

Prototype of smart office system using based security system

NASA Astrophysics Data System (ADS)

Prasetyo, T. F.; Zaliluddin, D.; Iqbal, M.

2018-05-01

Creating a new technology in the modern era gives a positive impact on business and industry. Internet of Things (IoT) as a new communication technology is very useful in realizing smart systems such as: smart home, smart office, smart parking and smart city. This study presents a prototype of the smart office system which was designed as a security system based on IoT. Smart office system development method used waterfall model. IoT-based smart office system used platform (project builder) cayenne so that. The data can be accessed and controlled through internet network from long distance. Smart office system used arduino mega 2560 microcontroller as a controller component. In this study, Smart office system is able to detect threats of dangerous objects made from metals, earthquakes, fires, intruders or theft and perform security monitoring outside the building by using raspberry pi cameras on autonomous robots in real time to the security guard.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurth, Thorsten; Pochinsky, Andrew; Sarje, Abhinav

Practitioners of lattice QCD/QFT have been some of the primary pioneer users of the state-of-the-art high-performance-computing systems, and contribute towards the stress tests of such new machines as soon as they become available. As with all aspects of high-performance-computing, I/O is becoming an increasingly specialized component of these systems. In order to take advantage of the latest available high-performance I/O infrastructure, to ensure reliability and backwards compatibility of data files, and to help unify the data structures used in lattice codes, we have incorporated parallel HDF5 I/O into the SciDAC supported USQCD software stack. Here we present the design andmore » implementation of this I/O framework. Our HDF5 implementation outperforms optimized QIO at the 10-20% level and leaves room for further improvement by utilizing appropriate dataset chunking.« less

Centralized Duplicate Removal Video Storage System with Privacy Preservation in IoT.

PubMed

Yan, Hongyang; Li, Xuan; Wang, Yu; Jia, Chunfu

2018-06-04

In recent years, the Internet of Things (IoT) has found wide application and attracted much attention. Since most of the end-terminals in IoT have limited capabilities for storage and computing, it has become a trend to outsource the data from local to cloud computing. To further reduce the communication bandwidth and storage space, data deduplication has been widely adopted to eliminate the redundant data. However, since data collected in IoT are sensitive and closely related to users' personal information, the privacy protection of users' information becomes a challenge. As the channels, like the wireless channels between the terminals and the cloud servers in IoT, are public and the cloud servers are not fully trusted, data have to be encrypted before being uploaded to the cloud. However, encryption makes the performance of deduplication by the cloud server difficult because the ciphertext will be different even if the underlying plaintext is identical. In this paper, we build a centralized privacy-preserving duplicate removal storage system, which supports both file-level and block-level deduplication. In order to avoid the leakage of statistical information of data, Intel Software Guard Extensions (SGX) technology is utilized to protect the deduplication process on the cloud server. The results of the experimental analysis demonstrate that the new scheme can significantly improve the deduplication efficiency and enhance the security. It is envisioned that the duplicated removal system with privacy preservation will be of great use in the centralized storage environment of IoT.

A user-oriented synthetic workload generator

NASA Technical Reports Server (NTRS)

Kao, Wei-Lun

1991-01-01

A user oriented synthetic workload generator that simulates users' file access behavior based on real workload characterization is described. The model for this workload generator is user oriented and job specific, represents file I/O operations at the system call level, allows general distributions for the usage measures, and assumes independence in the file I/O operation stream. The workload generator consists of three parts which handle specification of distributions, creation of an initial file system, and selection and execution of file I/O operations. Experiments on SUN NFS are shown to demonstrate the usage of the workload generator.

A proposed computer diagnostic system for malignant melanoma (CDSMM).

PubMed

Shao, S; Grams, R R

1994-04-01

This paper describes a computer diagnostic system for malignant melanoma. The diagnostic system is a rule base system based on image analyses and works under the PC windows environment. It consists of seven modules: I/O module, Patient/Clinic database, image processing module, classification module, rule base module and system control module. In the system, the image analyses are automatically carried out, and database management is efficient and fast. Both final clinic results and immediate results from various modules such as measured features, feature pictures and history records of the disease lesion can be presented on screen or printed out from each corresponding module or from the I/O module. The system can also work as a doctor's office-based tool to aid dermatologists with details not perceivable by the human eye. Since the system operates on a general purpose PC, it can be made portable if the I/O module is disconnected.

Randomized controlled trial for assessment of Internet of Things system to guide intensive glucose control in diabetes outpatients: Nagoya Health Navigator Study protocol.

PubMed

Onoue, Takeshi; Goto, Motomitsu; Kobayashi, Tomoko; Tominaga, Takashi; Ando, Masahiko; Honda, Hiroyuki; Yoshida, Yasuko; Tosaki, Takahiro; Yokoi, Hisashi; Kato, Sawako; Maruyama, Shoichi; Arima, Hiroshi

2017-08-01

The Internet of Things (IoT) allows collecting vast amounts of health-relevant data such as daily activity, body weight (BW), and blood pressure (BP) automatically. The use of IoT devices to monitor diabetic patients has been studied, but could not evaluate IoT-dependent effects because health data were not measured in control groups. This multicenter, open-label, randomized, parallel group study will compare the impact of intensive health guidance using IoT and conventional medical guidance on glucose control. It will be conducted in outpatients with type 2 diabetes for a period of 6 months. IoT devices to measure amount of daily activity, BW, and BP will be provided to IoT group patients. Healthcare professionals (HCPs) will provide appropriate feedback according to the data. Non-IoT control, patients will be given measurement devices that do not have a feedback function. The primary outcome is glycated hemoglobin at 6 months. The study has already enrolled 101 patients, 50 in the IoT group and 51 in the non-IoT group, at the two participating outpatient clinics. The baseline characteristics of two groups did not differ, except for triglycerides. This will be the first randomized, controlled study to evaluate IoT-dependent effects of intensive feedback from HCPs. The results will validate a new method of health-data collection and provision of feedback suitable for diabetes support with increased effectiveness and low cost.

Volcanism on Jupiter's moon Io and its relation to interior processes

NASA Astrophysics Data System (ADS)

Hamilton, Christopher

2013-04-01

Jupiter's moon Io is the most volcanically active body in the Solar System and offers insight into processes of tidal heating, melt generation, and magma ascent. Investigating these processes contributes to a better understanding of Io's geologic history, internal structure, and tidal dissipation mechanisms, as well as to understanding similar processes operating on other tidally-heated worlds (e.g., Europa, Enceladus, and some exoplanets). Four recent developments provide new observational constraints that prompt re-examination of the relationships between Io's surficial geology and interior structure. These developments include: (1) completion of the first 1:15,000,000 scale geologic map of Io based on a synthesis of Voyager and Galileo data; (2) re-interpretation of Galileo magnetometer data, which suggests that Io has a globally continuous subsurface magma ocean; (3) new global surveys of the power output from volcanic centers on Io; and (4) identification of an offset between volcano concentrations and surface heat flux maxima predicted by solid body tidal heating models. In this study, the spatial distributions of volcanic hotspots and paterae on Io are characterized using distance-based clustering techniques and nearest neighbor statistics. Distance-based clustering results support a dominant role for asthenospheric heating within Io, but show a 30-60° eastward offset in volcano concentrations relative to locations of predicted surface heat flux maxima. The observed asymmetry in volcano concentrations, with respect to the tidal axis, cannot be explained by existing solid body tidal heating models. However, identification of a global magma ocean within Io raises the intriguing possibility that a fluid tidal response—analogous to the heating of icy satellites by fluid tidal dissipation in their liquid oceans—may modify Io's thermal budget and locations of enhanced volcanism. The population density of volcanoes is greatest near the equator, which also agrees with predictions from asthensopheric-dominated tidal heating models, but the nearest neighbor analysis of hotspots (i.e., sites of active volcanism) and paterae (i.e., caldera-like volcano-tectonic depressions) reveals a random to uniform spatial organization. This suggests that Io may have an extensive subsurface magma reservoir with vigorous mantle convection, and/or a deep-mantle heating component, which reduces the amplitude of surface heat flux variations that would otherwise favor clustering. The tendency toward uniformity among volcanic systems may reflect their interaction through a process of magmatic lensing that focuses rising magma and inhibits volcanism in the surrounding capture zone. In summary, the distribution of volcanism on Io generally supports the presence of a globally extensive asthenosphere with local interactions occurring between volcanic systems, but a 30-60° eastward offset in the location of enhanced volcanism relative to predicted surface heat flux maxima cannot be explained by existing solid body tidal heating models. This may imply faster than synchronous rotation, state of stress controls on the locations of magma ascent, and/or a missing component in models of Io's interior, such as fluid tides generated within a globally extensive layer of interconnected partial melt.

Understanding the I/O Performance Gap Between Cori KNL and Haswell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Jialin; Koziol, Quincey; Tang, Houjun

2017-05-01

The Cori system at NERSC has two compute partitions with different CPU architectures: a 2,004 node Haswell partition and a 9,688 node KNL partition, which ranked as the 5th most powerful and fastest supercomputer on the November 2016 Top 500 list. The compute partitions share a common storage configuration, and understanding the IO performance gap between them is important, impacting not only to NERSC/LBNL users and other national labs, but also to the relevant hardware vendors and software developers. In this paper, we have analyzed performance of single core and single node IO comprehensively on the Haswell and KNL partitions,more » and have discovered the major bottlenecks, which include CPU frequencies and memory copy performance. We have also extended our performance tests to multi-node IO and revealed the IO cost difference caused by network latency, buffer size, and communication cost. Overall, we have developed a strong understanding of the IO gap between Haswell and KNL nodes and the lessons learned from this exploration will guide us in designing optimal IO solutions in many-core era.« less

Examining the accuracy of the infinite order sudden approximation using sensitivity analysis

NASA Astrophysics Data System (ADS)

Eno, Larry; Rabitz, Herschel

1981-08-01

A method is developed for assessing the accuracy of scattering observables calculated within the framework of the infinite order sudden (IOS) approximation. In particular, we focus on the energy sudden assumption of the IOS method and our approach involves the determination of the sensitivity of the IOS scattering matrix SIOS with respect to a parameter which reintroduces the internal energy operator ?0 into the IOS Hamiltonian. This procedure is an example of sensitivity analysis of missing model components (?0 in this case) in the reference Hamiltonian. In contrast to simple first-order perturbation theory a finite result is obtained for the effect of ?0 on SIOS. As an illustration, our method of analysis is applied to integral state-to-state cross sections for the scattering of an atom and rigid rotor. Results are generated within the He+H2 system and a comparison is made between IOS and coupled states cross sections and the corresponding IOS sensitivities. It is found that the sensitivity coefficients are very useful indicators of the accuracy of the IOS results. Finally, further developments and applications are discussed.

Integrated Semantics Service Platform for the Internet of Things: A Case Study of a Smart Office

PubMed Central

Ryu, Minwoo; Kim, Jaeho; Yun, Jaeseok

2015-01-01

The Internet of Things (IoT) allows machines and devices in the world to connect with each other and generate a huge amount of data, which has a great potential to provide useful knowledge across service domains. Combining the context of IoT with semantic technologies, we can build integrated semantic systems to support semantic interoperability. In this paper, we propose an integrated semantic service platform (ISSP) to support ontological models in various IoT-based service domains of a smart city. In particular, we address three main problems for providing integrated semantic services together with IoT systems: semantic discovery, dynamic semantic representation, and semantic data repository for IoT resources. To show the feasibility of the ISSP, we develop a prototype service for a smart office using the ISSP, which can provide a preset, personalized office environment by interpreting user text input via a smartphone. We also discuss a scenario to show how the ISSP-based method would help build a smart city, where services in each service domain can discover and exploit IoT resources that are wanted across domains. We expect that our method could eventually contribute to providing people in a smart city with more integrated, comprehensive services based on semantic interoperability. PMID:25608216

Integrated semantics service platform for the Internet of Things: a case study of a smart office.

PubMed

Ryu, Minwoo; Kim, Jaeho; Yun, Jaeseok

2015-01-19

The Internet of Things (IoT) allows machines and devices in the world to connect with each other and generate a huge amount of data, which has a great potential to provide useful knowledge across service domains. Combining the context of IoT with semantic technologies, we can build integrated semantic systems to support semantic interoperability. In this paper, we propose an integrated semantic service platform (ISSP) to support ontological models in various IoT-based service domains of a smart city. In particular, we address three main problems for providing integrated semantic services together with IoT systems: semantic discovery, dynamic semantic representation, and semantic data repository for IoT resources. To show the feasibility of the ISSP, we develop a prototype service for a smart office using the ISSP, which can provide a preset, personalized office environment by interpreting user text input via a smartphone. We also discuss a scenario to show how the ISSP-based method would help build a smart city, where services in each service domain can discover and exploit IoT resources that are wanted across domains. We expect that our method could eventually contribute to providing people in a smart city with more integrated, comprehensive services based on semantic interoperability.

Semi-elective intraosseous infusion after failed intravenous access in pediatric anesthesia.

PubMed

Neuhaus, Diego; Weiss, Markus; Engelhardt, Thomas; Henze, Georg; Giest, Judith; Strauss, Jochen; Eich, Christoph

2010-02-01

Intraosseous (IO) infusion is a well-established intervention to obtain vascular access in pediatric emergency medicine but is rarely used in routine pediatric anesthesia. In this observational study, we report on a series of 14 children in whom semi-elective IO infusion was performed under inhalational anesthesia after peripheral intravenous (IV) access had failed. Patient and case characteristics, technical details, and estimated timings of IO infusion as well as associated complications were reviewed. Data are median and range. IO infusion was successfully established in fourteen children [age: 0.1-6.00 years (median 0.72 years); weight: 3.5-12.0 kg (median 7.0 kg)]. The majority suffered from chronic cardiac, metabolic, or dysmorphic abnormalities. Estimated time taken from inhalational induction of anesthesia until insertion of an intraosseous needle was 26.5 min (15-65 min). The proximal tibia was cannulated in all patients. The automated EZIO IO system was used in eight patients and the manual COOK system in six patients. Drugs administered included hypnotics, opioids, neuromuscular blocking agents and reversals, cardiovascular drugs, antibiotics, and IV fluids. The IO cannulas were removed either in the operating theatre (n = 5), in the recovery room (n = 5), or in the ward (n = 4), after 73 min (19-225 min) in situ. There were no significant complications except one accidental postoperative dislocation. IO access represents a quick and reliable alternative for pediatric patients with prolonged difficult or failed IV access after inhalational induction of anesthesia.

Extreme Doppler Shifting of Io's Neutral Jets

NASA Astrophysics Data System (ADS)

Schmidt, Carl

2017-08-01

The dynamics and the extension of Jupiter's magnetosphere are determined by the massive internal plasma sources combined with the fast rotation. The vast majority of the plasma originates from the atmosphere of the moon Io, the most volcanically active body in our solar system. Here we propose to characterize the density and velocity of energetic neutral atoms escaping from Io's atmosphere. Exploiting the high resolution and sensitivity of the COS G130M spectral mode, we will measure the Doppler velocities of atomic O, S and Cl streams, which are energized through charge exchange and dissociative recombination of molecular ions. Prior COS observations of Io revealed a large number of emission lines from several ion and neutral species with excellent S/N, obtained over a single HST orbit. Those spectra were obtained surrounding eclipse geometry, where Doppler shifts are minimized and were restricted to Io itself rather than the stream region. Here we will target the extended clouds with only two orbits total when the moon is at eastern and western elongation for maximum Doppler shifts. The observations will provide new constraints on the diffuse large-scale cloud structures in the Jovian system and significantly improve our understanding of the transport of mass and energy within the Io-torus interaction. The absolute brightness, in combination with plasma parameters from line ratios/collision strengths, will allow us to quantify the outflow of energetic neutral atoms from Io's main sulfur-oxygen atmosphere for the first time.

I/O Router Placement and Fine-Grained Routing on Titan to Support Spider II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ezell, Matthew A; Dillow, David; Oral, H Sarp

2014-01-01

The Oak Ridge Leadership Computing Facility (OLCF) introduced the concept of Fine-Grained Routing in 2008 to improve I/O performance between the Jaguar supercomputer and Spider, OLCF s center-wide Lustre file system. Fine-grained routing organizes I/O paths to minimize congestion. Jaguar has since been upgraded to Titan, providing more than a ten-fold improvement in peak performance. To support the center s increased computational capacity and I/O demand, the Spider file system has been replaced with Spider II. Building on the lessons learned from Spider, an improved method for placing LNET routers was developed and implemented for Spider II. The fine-grained routingmore » scripts and configuration have been updated to provide additional optimizations and better match the system setup. This paper presents a brief history of fine-grained routing at OLCF, an introduction to the architectures of Titan and Spider II, methods for placing routers in Titan, and details about the fine-grained routing configuration.« less

Distributed service-based approach for sensor data fusion in IoT environments.

PubMed

Rodríguez-Valenzuela, Sandra; Holgado-Terriza, Juan A; Gutiérrez-Guerrero, José M; Muros-Cobos, Jesús L

2014-10-15

The Internet of Things (IoT) enables the communication among smart objects promoting the pervasive presence around us of a variety of things or objects that are able to interact and cooperate jointly to reach common goals. IoT objects can obtain data from their context, such as the home, office, industry or body. These data can be combined to obtain new and more complex information applying data fusion processes. However, to apply data fusion algorithms in IoT environments, the full system must deal with distributed nodes, decentralized communication and support scalability and nodes dynamicity, among others restrictions. In this paper, a novel method to manage data acquisition and fusion based on a distributed service composition model is presented, improving the data treatment in IoT pervasive environments.

Relationships Between Paterae, Mountains, and Hotspots on Io from a Global Database

NASA Technical Reports Server (NTRS)

Radebaugh, J.; Jaeger, W. L.; Keszthelyi, L. P.; Turtle, E. P.; Milazzo, M. P.; Perry, J.; McEwen, A. S.; Lopes, R.; Davies, A. G.; Geissler, P.

2004-01-01

Now that the Galileo spacecraft s tour of the Jupiter system is over, we seek to integrate all available datasets in the hopes of understanding Io as completely as possible. We have compiled information about the morphologies and locations of paterae (volcano-tectonic depressions), mountains, and hotspots on Io in a single database. It is our hope that an analysis of the spatial and temporal relationships between these features will provide more indications of the nature of the crust of Io and the mechanisms leading to these features formation. Since Io s tidal heat escapes through its crust, more knowledge about the crust will lead to an understanding of internal processes, such as magma generation and delivery to the surface, and magnitude and orientation of internal stresses.

Distributed Service-Based Approach for Sensor Data Fusion in IoT Environments

PubMed Central

Rodríguez-Valenzuela, Sandra; Holgado-Terriza, Juan A.; Gutiérrez-Guerrero, José M.; Muros-Cobos, Jesús L.

2014-01-01

The Internet of Things (IoT) enables the communication among smart objects promoting the pervasive presence around us of a variety of things or objects that are able to interact and cooperate jointly to reach common goals. IoT objects can obtain data from their context, such as the home, office, industry or body. These data can be combined to obtain new and more complex information applying data fusion processes. However, to apply data fusion algorithms in IoT environments, the full system must deal with distributed nodes, decentralized communication and support scalability and nodes dynamicity, among others restrictions. In this paper, a novel method to manage data acquisition and fusion based on a distributed service composition model is presented, improving the data treatment in IoT pervasive environments. PMID:25320907

PsyScript: a Macintosh application for scripting experiments.

PubMed

Bates, Timothy C; D'Oliveiro, Lawrence

2003-11-01

PsyScript is a scriptable application allowing users to describe experiments in Apple's compiled high-level object-oriented AppleScript language, while still supporting millisecond or better within-trial event timing (delays can be in milliseconds or refresh-based, and PsyScript can wait on external I/O, such as eye movement fixations). Because AppleScript is object oriented and system-wide, PsyScript experiments support complex branching, code reuse, and integration with other applications. Included AppleScript-based libraries support file handling and stimulus randomization and sampling, as well as more specialized tasks, such as adaptive testing. Advanced features include support for the BBox serial port button box, as well as a low-cost USB-based digital I/O card for millisecond timing, recording of any number and types of responses within a trial, novel responses, such as graphics tablet drawing, and use of the Macintosh sound facilities to provide an accurate voice key, saving voice responses to disk, scriptable image creation, support for flicker-free animation, and gaze-dependent masking. The application is open source, allowing researchers to enhance the feature set and verify internal functions. Both the application and the source are available for free download at www.maccs.mq.edu.au/-tim/psyscript/.

The condensation and vaporization behavior of ices containing SO2, H2S, and CO2: Implications for Io

NASA Technical Reports Server (NTRS)

Sandford, Scott A.; Allamandola, Louis J.

1993-01-01

In an extension of previously reported work on ices containing CO, CO2, H2O, CH3OH, NH3, and H2, measurements of the physical and infrared spectral properties of ices containing molecules relevant to Jupiter's moon Io are presented. These include studies on ice systems containing SO2, H2S, and CO2. The condensation and sublimation behaviors of each ice system and surface binding energies of their components are discussed. The surface binding energies can be used to calculate the residence times of the molecules on a surface as a function of temperature and thus represent important parameters for any calculation that attempts to model the transport of these molecules on Io's surface. The derived values indicate that SO2 frosts on Io are likely to anneal rapidly, resulting in less fluffy, 'glassy' ices and that H2S can be trapped in the SO2 ices of Io during night-time hours provided that SO2 deposition rates are on the order of 5 micrometers/hr or larger.

Comparison of Respiratory Resistance Measurements Made with an Airflow Perturbation Device with Those from Impulse Oscillometry

PubMed Central

Pan, J.; Saltos, A.; Smith, D.; Johnson, A.; Vossoughi, J.

2013-01-01

The airflow perturbation device (APD) has been developed as a portable, easy to use, and a rapid response instrument for measuring respiratory resistance in humans. However, the APD has limited data validating it against the established techniques. This study used a mechanical system to simulate the normal range of human breathing to validate the APD with the clinically accepted impulse oscillometry (IOS) technique. The validation system consisted of a sinusoidal flow generator with ten standardized resistance configurations that were shown to represent a total range of resistances from 0.12 to 0.95 kPa·L−1 ·s (1.2–9.7 cm H2O·L−1 ·s). Impulse oscillometry measurements and APD measurements of the mechanical system were recorded and compared at a constant airflow of 0.15 L·s−1. Both the IOS and APD measurments were accurate in assessing nominal resistance. In addition, a strong linear relationship was observed between APD measurements and IOS measurements (R 2 = 0.999). A second series of measurements was made on ten human volunteers with external resistors added in their respiratory flow paths. Once calibrated with the mechanical system, the APD gave respiratory resistance measurements within 5% of IOS measurements. Because of their comparability to IOS measurements, APD measurements are shown to be valid representations of respiratory resistance. PMID:27006908

Mobile Learning Technology Based on iOS Devices to Support Students with Special Education Needs

ERIC Educational Resources Information Center

Fernandez-Lopez, Alvaro; Rodriguez-Fortiz, Maria Jose; Rodriguez-Almendros, Maria Luisa; Martinez-Segura, Maria Jose

2013-01-01

Students with special education have difficulties to develop cognitive abilities and acquire new knowledge. They could also need to improve their behavior, communication and relationships with their environment. The development of customizable and adaptable applications tailored to them provides many benefits as it helps mold the learning process…

Pontine Mechanisms of Respiratory Control

PubMed Central

Dutschmann, Mathias; Dick, Thomas E.

2015-01-01

Pontine respiratory nuclei provide synaptic input to medullary rhythmogenic circuits to shape and adapt the breathing pattern. An understanding of this statement depends on appreciating breathing as a behavior, rather than a stereotypic rhythm. In this review, we focus on the pontine-mediated inspiratory off-switch (IOS) associated with postinspiratory glottal constriction. Further, IOS is examined in the context of pontine regulation of glottal resistance in response to multimodal sensory inputs and higher commands, which in turn rules timing, duration, and patterning of respiratory airflow. In addition, network plasticity in respiratory control emerges during the development of the pons. Synaptic plasticity is required for dynamic and efficient modulation of the expiratory breathing pattern to cope with rapid changes from eupneic to adaptive breathing linked to exploratory (foraging and sniffing) and expulsive (vocalizing, coughing, sneezing, and retching) behaviors, as well as conveyance of basic emotions. The speed and complexity of changes in the breathing pattern of behaving animals implies that “learning to breathe” is necessary to adjust to changing internal and external states to maintain homeostasis and survival. PMID:23720253

Converting a conventional wired-halogen illuminated indirect ophthalmoscope to a wireless-light emitting diode illuminated indirect ophthalmoscope in less than 1000/- rupees.

PubMed

Kothari, Mihir; Kothari, Kedar; Kadam, Sanjay; Mota, Poonam; Chipade, Snehal

2015-01-01

To report the "do it yourself" method of converting an existing wired-halogen indirect ophthalmoscope (IO) to a wireless-light emitting diode (LED) IO and report the preferences of the patients and the ophthalmologists. In this prospective observational study, a conventional IO was converted to wireless-LED IO using easily available, affordable electrical components. Conventional and the converted IO were then used to perform photo-stress test and take the feedback of subjects and the ophthalmologists regarding its handling and illumination characteristics. The cost of conversion to wireless-LED was 815/- rupees. Twenty-nine subjects, mean age 34.3 [formula in text] 10 years with normal eyes were recruited in the study. Between the two illumination systems, there was no statistical difference in the magnitude of the visual acuity loss and the time to recovery of acuity and the bleached vision on photo-stress test, although the visual recovery was clinically faster with LED illumination. The heat sensation was more with halogen illumination than the LED (P = 0.009). The ophthalmologists rated wireless-LED IO higher than wired-halogen IO on the handling, examination comfort, patient's visual comfort and quality of the image. Twenty-two (81%) ophthalmologists wanted to change over to wireless-LED IO. Converting to wireless-LED IO is easy, cost-effective and preferred over a wired-halogen indirect ophthalmoscope.

Loki as viewed by Galileo NIMS

NASA Image and Video Library

1999-11-19

This image shows Loki, the most powerful volcano in the solar system, which has been constantly active on Jupiter moon Io. NASA Galileo spacecraft took these images during its approach to Io on October 10, 1999.

Interactive Office user's manual

NASA Technical Reports Server (NTRS)

Montgomery, Edward E.; Lowers, Benjamin; Nabors, Terri L.

1990-01-01

Given here is a user's manual for Interactive Office (IO), an executive office tool for organization and planning, written specifically for Macintosh. IO is a paperless management tool to automate a related group of individuals into one productive system.

Accuracy and precision of 3 intraoral scanners and accuracy of conventional impressions: A novel in vivo analysis method.

PubMed

Nedelcu, R; Olsson, P; Nyström, I; Rydén, J; Thor, A

2018-02-01

To evaluate a novel methodology using industrial scanners as a reference, and assess in vivo accuracy of 3 intraoral scanners (IOS) and conventional impressions. Further, to evaluate IOS precision in vivo. Four reference-bodies were bonded to the buccal surfaces of upper premolars and incisors in five subjects. After three reference-scans, ATOS Core 80 (ATOS), subjects were scanned three times with three IOS systems: 3M True Definition (3M), CEREC Omnicam (OMNI) and Trios 3 (TRIOS). One conventional impression (IMPR) was taken, 3M Impregum Penta Soft, and poured models were digitized with laboratory scanner 3shape D1000 (D1000). Best-fit alignment of reference-bodies and 3D Compare Analysis was performed. Precision of ATOS and D1000 was assessed for quantitative evaluation and comparison. Accuracy of IOS and IMPR were analyzed using ATOS as reference. Precision of IOS was evaluated through intra-system comparison. Precision of ATOS reference scanner (mean 0.6 μm) and D1000 (mean 0.5 μm) was high. Pairwise multiple comparisons of reference-bodies located in different tooth positions displayed a statistically significant difference of accuracy between two scanner-groups: 3M and TRIOS, over OMNI (p value range 0.0001 to 0.0006). IMPR did not show any statistically significant difference to IOS. However, deviations of IOS and IMPR were within a similar magnitude. No statistical difference was found for IOS precision. The methodology can be used for assessing accuracy of IOS and IMPR in vivo in up to five units bilaterally from midline. 3M and TRIOS had a higher accuracy than OMNI. IMPR overlapped both groups. Intraoral scanners can be used as a replacement for conventional impressions when restoring up to ten units without extended edentulous spans. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Activation and evaluation of GaN photocathodes

NASA Astrophysics Data System (ADS)

Qian, Yunsheng; Chang, Benkang; Qiao, Jiangliang; Zhang, Yijun; Fu, Rongguo; Qiu, Yafeng

2009-09-01

Gallium Nitride (GaN) photocathodes are potentially attractive as UV detective materials and electron sources. Based on the activation and evaluation system for GaAs photocathode, which consists of ultra-high vacuum (UHV) activation chamber, multi-information measurement system, X-ray photoelectron spectroscopy (XPS), and ultraviolet ray photoelectron spectroscopy (UPS), the control and measurement system for the activation of UV photocathodes was developed. The developed system, which consists of Xenon lamp, monochromator with scanner, signal-processing module, power control unit of Cs and O source, A/D adapter, digital I/O card, computer and software, can control the activation of GaN photocathodes and measure on-line the spectral response curves of GaN photocathodes. GaN materials on sapphire substrate were grown by Metal-Organic Chemical Vapor Deposition (MOCVD) with p-type Mg doping. The GaN materials were activated by Cs-O. The spectral response and quantum efficiency (QE) were measured and calculated. The experiment results are discussed.

A Novel Secure IoT-Based Smart Home Automation System Using a Wireless Sensor Network.

PubMed

Pirbhulal, Sandeep; Zhang, Heye; E Alahi, Md Eshrat; Ghayvat, Hemant; Mukhopadhyay, Subhas Chandra; Zhang, Yuan-Ting; Wu, Wanqing

2016-12-30

Wireless sensor networks (WSNs) provide noteworthy benefits over traditional approaches for several applications, including smart homes, healthcare, environmental monitoring, and homeland security. WSNs are integrated with the Internet Protocol (IP) to develop the Internet of Things (IoT) for connecting everyday life objects to the internet. Hence, major challenges of WSNs include: (i) how to efficiently utilize small size and low-power nodes to implement security during data transmission among several sensor nodes; (ii) how to resolve security issues associated with the harsh and complex environmental conditions during data transmission over a long coverage range. In this study, a secure IoT-based smart home automation system was developed. To facilitate energy-efficient data encryption, a method namely Triangle Based Security Algorithm (TBSA) based on efficient key generation mechanism was proposed. The proposed TBSA in integration of the low power Wi-Fi were included in WSNs with the Internet to develop a novel IoT-based smart home which could provide secure data transmission among several associated sensor nodes in the network over a long converge range. The developed IoT based system has outstanding performance by fulfilling all the necessary security requirements. The experimental results showed that the proposed TBSA algorithm consumed less energy in comparison with some existing methods.

A Novel Secure IoT-Based Smart Home Automation System Using a Wireless Sensor Network

PubMed Central

Pirbhulal, Sandeep; Zhang, Heye; E Alahi, Md Eshrat; Ghayvat, Hemant; Mukhopadhyay, Subhas Chandra; Zhang, Yuan-Ting; Wu, Wanqing

2016-01-01

Wireless sensor networks (WSNs) provide noteworthy benefits over traditional approaches for several applications, including smart homes, healthcare, environmental monitoring, and homeland security. WSNs are integrated with the Internet Protocol (IP) to develop the Internet of Things (IoT) for connecting everyday life objects to the internet. Hence, major challenges of WSNs include: (i) how to efficiently utilize small size and low-power nodes to implement security during data transmission among several sensor nodes; (ii) how to resolve security issues associated with the harsh and complex environmental conditions during data transmission over a long coverage range. In this study, a secure IoT-based smart home automation system was developed. To facilitate energy-efficient data encryption, a method namely Triangle Based Security Algorithm (TBSA) based on efficient key generation mechanism was proposed. The proposed TBSA in integration of the low power Wi-Fi were included in WSNs with the Internet to develop a novel IoT-based smart home which could provide secure data transmission among several associated sensor nodes in the network over a long converge range. The developed IoT based system has outstanding performance by fulfilling all the necessary security requirements. The experimental results showed that the proposed TBSA algorithm consumed less energy in comparison with some existing methods. PMID:28042831

Comparison of the Fluid Resuscitation Rate with and without External Pressure Using Two Intraosseous Infusion Systems for Adult Emergencies, the CITRIN (Comparison of InTRaosseous infusion systems in emergency medicINe)-Study

PubMed Central

Gries, André; Hossfeld, Björn; Bechmann, Ingo; Bernhard, Michael

2015-01-01

Introduction Intraosseous infusion is recommended if peripheral venous access fails for cardiopulmonary resuscitation or other medical emergencies. The aim of this study, using body donors, was to compare a semi-automatic (EZ-IO®) device at two insertion sites and a sternal intraosseous infusion device (FASTR™). Methods Twenty-seven medical students being inexperienced first-time users were randomized into three groups using EZ-IO and FASTR. The following data were evaluated: attempts required for successful placement, insertion time and flow rates with and without external pressure to the infusion. Results The first-pass insertion success of the EZ-IO tibia, EZ-IO humerus and FASTR was 91%, 77%, and 95%, respectively. Insertion times (MW±SD) did not show significant differences with 17±7 (EZ-IO tibia) vs. 29±42 (EZ-IO humerus) vs. 33±21 (FASTR), respectively. One-minute flow rates using external pressures between 0 mmHg and 300 mmHg ranged between 27±5 to 69±54 ml/min (EZ-IO tibia), 16±3 to 60±44 ml/min (EZ-IO humerus) and 53±2 to 112±47 ml/min (FASTR), respectively. Concerning pressure-related increases in flow rates, negligible correlations were found for the EZ-IO tibia in all time frames (c = 0.107–0.366; p≤0.013), moderate positive correlations were found for the EZ-IO humerus after 5 minutes (c = 0.489; p = 0.021) and strong positive correlations were found for the FASTR in all time frames (c = 0.63–0.80; p≤0.007). Post-hoc statistical power was 0.62 with the given sample size. Conclusions The experiments with first-time users applying EZ-IO and FASTR in body donors indicate that both devices may be effective intraosseous infusion devices, likely suitable for fluid resuscitation using a pressure bag. Variations in flow rate may limit their reliability. Larger sample sizes will prospectively be required to substantiate our findings. PMID:26630579

Comparison of the Fluid Resuscitation Rate with and without External Pressure Using Two Intraosseous Infusion Systems for Adult Emergencies, the CITRIN (Comparison of InTRaosseous infusion systems in emergency medicINe)-Study.

PubMed

Hammer, Niels; Möbius, Robert; Gries, André; Hossfeld, Björn; Bechmann, Ingo; Bernhard, Michael

2015-01-01

Intraosseous infusion is recommended if peripheral venous access fails for cardiopulmonary resuscitation or other medical emergencies. The aim of this study, using body donors, was to compare a semi-automatic (EZ-IO®) device at two insertion sites and a sternal intraosseous infusion device (FASTR™). Twenty-seven medical students being inexperienced first-time users were randomized into three groups using EZ-IO and FASTR. The following data were evaluated: attempts required for successful placement, insertion time and flow rates with and without external pressure to the infusion. The first-pass insertion success of the EZ-IO tibia, EZ-IO humerus and FASTR was 91%, 77%, and 95%, respectively. Insertion times (MW ± SD) did not show significant differences with 17 ± 7 (EZ-IO tibia) vs. 29 ± 42 (EZ-IO humerus) vs. 33 ± 21 (FASTR), respectively. One-minute flow rates using external pressures between 0 mmHg and 300 mmHg ranged between 27 ± 5 to 69 ± 54 ml/min (EZ-IO tibia), 16 ± 3 to 60 ± 44 ml/min (EZ-IO humerus) and 53 ± 2 to 112 ± 47 ml/min (FASTR), respectively. Concerning pressure-related increases in flow rates, negligible correlations were found for the EZ-IO tibia in all time frames (c = 0.107-0.366; p ≤ 0.013), moderate positive correlations were found for the EZ-IO humerus after 5 minutes (c = 0.489; p = 0.021) and strong positive correlations were found for the FASTR in all time frames (c = 0.63-0.80; p ≤ 0.007). Post-hoc statistical power was 0.62 with the given sample size. The experiments with first-time users applying EZ-IO and FASTR in body donors indicate that both devices may be effective intraosseous infusion devices, likely suitable for fluid resuscitation using a pressure bag. Variations in flow rate may limit their reliability. Larger sample sizes will prospectively be required to substantiate our findings.

US-CERT Control System Center Input/Output (I/O) Conceputal Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2005-02-01

This document was prepared for the US-CERT Control Systems Center of the National Cyber Security Division (NCSD) of the Department of Homeland Security (DHS). DHS has been tasked under the Homeland Security Act of 2002 to coordinate the overall national effort to enhance the protection of the national critical infrastructure. Homeland Security Presidential Directive HSPD-7 directs the federal departments to identify and prioritize critical infrastructure and protect it from terrorist attack. The US-CERT National Strategy for Control Systems Security was prepared by the NCSD to address the control system security component addressed in the National Strategy to Secure Cyberspace andmore » the National Strategy for the Physical Protection of Critical Infrastructures and Key Assets. The US-CERT National Strategy for Control Systems Security identified five high-level strategic goals for improving cyber security of control systems; the I/O upgrade described in this document supports these goals. The vulnerability assessment Test Bed, located in the Information Operations Research Center (IORC) facility at Idaho National Laboratory (INL), consists of a cyber test facility integrated with multiple test beds that simulate the nation's critical infrastructure. The fundamental mission of the Test Bed is to provide industry owner/operators, system vendors, and multi-agency partners of the INL National Security Division a platform for vulnerability assessments of control systems. The Input/Output (I/O) upgrade to the Test Bed (see Work Package 3.1 of the FY-05 Annual Work Plan) will provide for the expansion of assessment capabilities within the IORC facility. It will also provide capabilities to connect test beds within the Test Range and other Laboratory resources. This will allow real time I/O data input and communication channels for full replications of control systems (Process Control Systems [PCS], Supervisory Control and Data Acquisition Systems [SCADA], and components). This will be accomplished through the design and implementation of a modular infrastructure of control system, communications, networking, computing and associated equipment, and measurement/control devices. The architecture upgrade will provide a flexible patching system providing a quick ''plug and play''configuration through various communication paths to gain access to live I/O running over specific protocols. This will allow for in-depth assessments of control systems in a true-to-life environment. The full I/O upgrade will be completed through a two-phased approach. Phase I, funded by DHS, expands the capabilities of the Test Bed by developing an operational control system in two functional areas, the Science & Technology Applications Research (STAR) Facility and the expansion of various portions of the Test Bed. Phase II (see Appendix A), funded by other programs, will complete the full I/O upgrade to the facility.« less

High Performance Input/Output for Parallel Computer Systems

NASA Technical Reports Server (NTRS)

Ligon, W. B.

1996-01-01

The goal of our project is to study the I/O characteristics of parallel applications used in Earth Science data processing systems such as Regional Data Centers (RDCs) or EOSDIS. Our approach is to study the runtime behavior of typical programs and the effect of key parameters of the I/O subsystem both under simulation and with direct experimentation on parallel systems. Our three year activity has focused on two items: developing a test bed that facilitates experimentation with parallel I/O, and studying representative programs from the Earth science data processing application domain. The Parallel Virtual File System (PVFS) has been developed for use on a number of platforms including the Tiger Parallel Architecture Workbench (TPAW) simulator, The Intel Paragon, a cluster of DEC Alpha workstations, and the Beowulf system (at CESDIS). PVFS provides considerable flexibility in configuring I/O in a UNIX- like environment. Access to key performance parameters facilitates experimentation. We have studied several key applications fiom levels 1,2 and 3 of the typical RDC processing scenario including instrument calibration and navigation, image classification, and numerical modeling codes. We have also considered large-scale scientific database codes used to organize image data.

Constraining Plasma Conditions of the IPT via Spectral Analysis of UV & Visible Emissions and Comparing with a Physical Chemistry Model

NASA Astrophysics Data System (ADS)

Nerney, E. G.; Bagenal, F.; Yoshioka, K.; Schmidt, C.

2017-12-01

Io emits volcanic gases into space at a rate of about a ton per second. The gases become ionized and trapped in Jupiter's strong magnetic field, forming a torus of plasma that emits 2 terawatts of UV emissions. In recent work re-analyzing UV emissions observed by Voyager, Galileo, & Cassini, we found plasma conditions consistent with a physical chemistry model with a neutral source of dissociated sulfur dioxide from Io (Nerney et al., 2017). In further analysis of UV observations from JAXA's Hisaki mission (using our spectral emission model) we constrain the torus composition with ground based observations. The physical chemistry model (adapted from Delamere et al., 2005) is then used to match derived plasma conditions. We correlate the oxygen to sulfur ratio of the neutral source with volcanic eruptions to understand the change in magnetospheric plasma conditions. Our goal is to better understand and constrain both the temporal and spatial variability of the flow of mass and energy from Io's volcanic atmosphere to Jupiter's dynamic magnetosphere.

Genomic features of Lactococcus lactis IO-1, a lactic acid bacterium that utilizes xylose and produces high levels of L-lactic acid.

PubMed

Shimizu-Kadota, Mariko; Kato, Hiroaki; Shiwa, Yuh; Oshima, Kenshiro; Machii, Miki; Araya-Kojima, Tomoko; Zendo, Takeshi; Hattori, Masahira; Sonomoto, Kenji; Yoshikawa, Hirofumi

2013-01-01

Lactococcus lactis IO-1 (JCM7638) produces L-lactic acid predominantly when grown at high xylose concentrations, and its utilization is highly desired in the green plastics industry. Therefore it is worthwhile studying its genomic traits. In this study, we focused on (i) genes of possible horizontal transfer derivation (prophages, the nisin-sucrose transposon, and several restriction-modification systems), and (ii) genes for the synthetic pathways of amino acids and vitamins in the IO-1 genome. In view of the results of this analysis, we consider their meanings in strain IO-1.

Jovian dust streams: A monitor of Io's volcanic plume activity

USGS Publications Warehouse

Kruger, H.; Geissler, P.; Horanyi, M.; Graps, A.L.; Kempf, S.; Srama, R.; Moragas-Klostermeyer, G.; Moissl, R.; Johnson, T.V.; Grun, E.

2003-01-01

Streams of high speed dust particles originate from Jupiter's moon Io. After release from Io, the particles collect electric charges in the Io plasma torus, gain energy from the co-rotating electric field of Jupiter's magnetosphere, and leave the Jovian system into interplanetary space with escape speeds over 200 km s-1. The Galileo spacecraft has continuously monitored the dust streams during 34 revolutions about Jupiter between 1996 and 2002. The observed dust fluxes exhibit large orbit-to-orbit variability due to systematic and stochastic changes. After removal of the systematic variations, the total dust emission rate of Io has been calculated. It varies between 10-3 and 10 kg s-1, and is typically in the range of 0.1 to 1 kg s-1. We compare the dust emission rate with other markers of volcanic activity on Io like large-area surface changes caused by volcanic deposits and sightings of volcanic plumes. Copyright 2003 by the American Geophysical Union.

Io Sodium Cloud Green-yellow Filter

NASA Image and Video Library

1997-12-18

This image of Jupiter moon Io and its surrounding sky is shown in false color. This image was taken on Nov. 9, 1996 through the green-yellow filter of the solid state imaging CCD system aboard NASA Galileo spacecraft.

Io Sodium Cloud Clear Filter

NASA Image and Video Library

1997-12-18

This image of Jupiter moon Io and its surrounding sky is shown in false color. It was taken at 5 hours 30 minutes Universal Time on Nov. 9, 1996 by the solid state imaging CCD system aboard NASA Galileo spacecraft,

Dynamic I/O Power Management for Hard Real-Time Systems

DTIC Science & Technology

2005-01-01

recently emerged as an attractive alternative to inflexible hardware solutions. DPM for hard real - time systems has received relatively little attention...In particular, energy-driven I/O device scheduling for real - time systems has not been considered before. We present the first online DPM algorithm...which we call Low Energy Device Scheduler (LEDES), for hard real - time systems . LEDES takes as inputs a predetermined task schedule and a device-usage

Apps seeking theories: results of a study on the use of health behavior change theories in cancer survivorship mobile apps.

PubMed

Vollmer Dahlke, Deborah; Fair, Kayla; Hong, Y Alicia; Beaudoin, Christopher E; Pulczinski, Jairus; Ory, Marcia G

2015-03-27

Thousands of mobile health apps are now available for use on mobile phones for a variety of uses and conditions, including cancer survivorship. Many of these apps appear to deliver health behavior interventions but may fail to consider design considerations based in human computer interface and health behavior change theories. This study is designed to assess the presence of and manner in which health behavior change and health communication theories are applied in mobile phone cancer survivorship apps. The research team selected a set of criteria-based health apps for mobile phones and assessed each app using qualitative coding methods to assess the application of health behavior change and communication theories. Each app was assessed using a coding derived from the taxonomy of 26 health behavior change techniques by Abraham and Michie with a few important changes based on the characteristics of mHealth apps that are specific to information processing and human computer interaction such as control theory and feedback systems. A total of 68 mobile phone apps and games built on the iOS and Android platforms were coded, with 65 being unique. Using a Cohen's kappa analysis statistic, the inter-rater reliability for the iOS apps was 86.1 (P<.001) and for the Android apps, 77.4 (P<.001). For the most part, the scores for inclusion of theory-based health behavior change characteristics in the iOS platform cancer survivorship apps were consistently higher than those of the Android platform apps. For personalization and tailoring, 67% of the iOS apps (24/36) had these elements as compared to 38% of the Android apps (12/32). In the area of prompting for intention formation, 67% of the iOS apps (34/36) indicated these elements as compared to 16% (5/32) of the Android apps. Mobile apps are rapidly emerging as a way to deliver health behavior change interventions that can be tailored or personalized for individuals. As these apps and games continue to evolve and include interactive and adaptive sensors and other forms of dynamic feedback, their content and interventional elements need to be grounded in human computer interface design and health behavior and communication theory and practice.

Apps Seeking Theories: Results of a Study on the Use of Health Behavior Change Theories in Cancer Survivorship Mobile Apps

PubMed Central

Fair, Kayla; Hong, Y Alicia; Beaudoin, Christopher E; Pulczinski, Jairus; Ory, Marcia G

2015-01-01

Background Thousands of mobile health apps are now available for use on mobile phones for a variety of uses and conditions, including cancer survivorship. Many of these apps appear to deliver health behavior interventions but may fail to consider design considerations based in human computer interface and health behavior change theories. Objective This study is designed to assess the presence of and manner in which health behavior change and health communication theories are applied in mobile phone cancer survivorship apps. Methods The research team selected a set of criteria-based health apps for mobile phones and assessed each app using qualitative coding methods to assess the application of health behavior change and communication theories. Each app was assessed using a coding derived from the taxonomy of 26 health behavior change techniques by Abraham and Michie with a few important changes based on the characteristics of mHealth apps that are specific to information processing and human computer interaction such as control theory and feedback systems. Results A total of 68 mobile phone apps and games built on the iOS and Android platforms were coded, with 65 being unique. Using a Cohen’s kappa analysis statistic, the inter-rater reliability for the iOS apps was 86.1 (P<.001) and for the Android apps, 77.4 (P<.001). For the most part, the scores for inclusion of theory-based health behavior change characteristics in the iOS platform cancer survivorship apps were consistently higher than those of the Android platform apps. For personalization and tailoring, 67% of the iOS apps (24/36) had these elements as compared to 38% of the Android apps (12/32). In the area of prompting for intention formation, 67% of the iOS apps (34/36) indicated these elements as compared to 16% (5/32) of the Android apps. Conclusions Mobile apps are rapidly emerging as a way to deliver health behavior change interventions that can be tailored or personalized for individuals. As these apps and games continue to evolve and include interactive and adaptive sensors and other forms of dynamic feedback, their content and interventional elements need to be grounded in human computer interface design and health behavior and communication theory and practice. PMID:25830810

A Proposal for IoT Dynamic Routes Selection Based on Contextual Information

PubMed Central

Filho, Raimir Holanda; Rabelo, Ricardo de A. L.; Sousa, Natanael de C.; Filho, José C. C. L. S.

2018-01-01

The Internet of Things (IoT) is based on interconnection of intelligent and addressable devices, allowing their autonomy and proactive behavior with Internet connectivity. Data dissemination in IoT usually depends on the application and requires context-aware routing protocols that must include auto-configuration features (which adapt the behavior of the network at runtime, based on context information). This paper proposes an approach for IoT route selection using fuzzy logic in order to attain the requirements of specific applications. In this case, fuzzy logic is used to translate in math terms the imprecise information expressed by a set of linguistic rules. For this purpose, four Objective Functions (OFs) are proposed for the Routing Protocol for Low Power and Loss Networks (RPL); such OFs are dynamically selected based on context information. The aforementioned OFs are generated from the fusion of the following metrics: Expected Transmission Count (ETX), Number of Hops (NH) and Energy Consumed (EC). The experiments performed through simulation, associated with the statistical data analysis, conclude that this proposal provides high reliability by successfully delivering nearly 100% of data packets, low delay for data delivery and increase in QoS. In addition, an 30% improvement is attained in the network life time when using one of proposed objective function, keeping the devices alive for longer duration. PMID:29373499

Electrical Design and Evaluation of Asynchronous Serial Bus Communication Network of 48 Sensor Platform LSIs with Single-Ended I/O for Integrated MEMS-LSI Sensors.

PubMed

Shao, Chenzhong; Tanaka, Shuji; Nakayama, Takahiro; Hata, Yoshiyuki; Muroyama, Masanori

2018-01-15

For installing many sensors in a limited space with a limited computing resource, the digitization of the sensor output at the site of sensation has advantages such as a small amount of wiring, low signal interference and high scalability. For this purpose, we have developed a dedicated Complementary Metal-Oxide-Semiconductor (CMOS) Large-Scale Integration (LSI) (referred to as "sensor platform LSI") for bus-networked Micro-Electro-Mechanical-Systems (MEMS)-LSI integrated sensors. In this LSI, collision avoidance, adaptation and event-driven functions are simply implemented to relieve data collision and congestion in asynchronous serial bus communication. In this study, we developed a network system with 48 sensor platform LSIs based on Printed Circuit Board (PCB) in a backbone bus topology with the bus length being 2.4 m. We evaluated the serial communication performance when 48 LSIs operated simultaneously with the adaptation function. The number of data packets received from each LSI was almost identical, and the average sampling frequency of 384 capacitance channels (eight for each LSI) was 73.66 Hz.

Evaluation of Saccharomyces cerevisiae GAS1 with respect to its involvement in tolerance to low pH and salt stress.

PubMed

Matsushika, Akinori; Suzuki, Toshihiro; Goshima, Tetsuya; Hoshino, Tamotsu

2017-08-01

We previously showed that overexpression of IoGAS1, which was isolated from the multiple stress-tolerant yeast Issatchenkia orientalis, endows Saccharomyces cerevisiae cells with the ability to grow and ferment under acidic and high-salt conditions. The deduced amino acid sequence of the IoGAS1 gene product exhibits 60% identity with the S. cerevisiae Gas1 protein, a glycosylphosphatidylinositol-anchored protein essential for maintaining cell wall integrity. However, the functional roles of ScGAS1 in stress tolerance and pH regulation remain unclear. In the present study, we characterized ScGAS1 regarding its roles in tolerance to low pH and high salt concentrations. Transcriptional analysis indicated that, as for the IoGAS1 gene, ScGAS1 expression was pH dependent, with maximum expression at pH 3.0; the presence of salt increased endogenous expression of both GAS1 genes at almost all pH levels. These results suggested that ScGAS1, like IoGAS1, is involved in a novel acid- and salt-stress adaptation mechanism in S. cerevisiae. Overexpression of ScGAS1 in S. cerevisiae improved growth and ethanol production from glucose under acid stress without added salt, although the stress tolerance of the ScGAS1-overexpressing strain was inferior to that of the IoGAS1-overexpressing strain. However, overexpression of ScGAS1 did not result in increased tolerance of S. cerevisiae to combined acid and salt stress, even though ScGAS1 appears to be a salt-responsive gene. Thus, ScGAS1 is directly implicated in tolerance to low pH but does not confer salinity tolerance, supporting the view that ScGAS1 and IoGAS1 have overlapping yet distinct roles in stress tolerance in yeast. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Io's Sodium Cloud (Green-yellow Filter)

NASA Technical Reports Server (NTRS)

1997-01-01

This image of Jupiter's moon Io and its surrounding sky is shown in false color. North is at the top, and east is to the right. Most of Io's visible surface is in shadow, though one can see part of a white crescent on its western side. This crescent is being illuminated mostly by 'Jupitershine' (i.e. sunlight reflected off Jupiter).

The striking burst of white light near Io's eastern equatorial edge is sunlight being scattered by the plume of the volcano Prometheus. Prometheus lies just beyond the visible edge of the moon on Io's far side. Its plume extends about 100 kilometers above the surface, and is being hit by sunlight just a little east of Io's eastern edge.

Scattered light from Prometheus' plume and Io's lit crescent also contribute to the diffuse yellowish emission which appears throughout much of the sky. However, much of this emission comes from Io's Sodium Cloud: sodium atoms within Io's extensive material halo are scattering sunlight at the yellow wavelength of about 589 nanometers.

This image was taken at 5 hours 30 minutes Universal Time on Nov. 9, 1996 through the green-yellow filter of the solid state imaging (CCD) system aboard NASA's Galileo spacecraft. Galileo was then in Jupiter's shadow, and located about 2.3 million kilometers (about 32 Jovian radii) from both Jupiter and Io.

The Jet Propulsion Laboratory, Pasadena, CA, manages the mission for NASA's Office of Space Science, Washington D.C. This image and other images and data received from Galileo are posted on the World Wide Web Galileo mission home page at: http://galileo.jpl.nasa.gov.

TRIO: Burst Buffer Based I/O Orchestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Teng; Oral, H Sarp; Pritchard, Michael

The growing computing power on leadership HPC systems is often accompanied by ever-escalating failure rates. Checkpointing is a common defensive mechanism used by scientific applications for failure recovery. However, directly writing the large and bursty checkpointing dataset to parallel filesystem can incur significant I/O contention on storage servers. Such contention in turn degrades the raw bandwidth utilization of storage servers and prolongs the average job I/O time of concurrent applications. Recently burst buffer has been proposed as an intermediate layer to absorb the bursty I/O traffic from compute nodes to storage backend. But an I/O orchestration mechanism is still desiredmore » to efficiently move checkpointing data from bursty buffers to storage backend. In this paper, we propose a burst buffer based I/O orchestration framework, named TRIO, to intercept and reshape the bursty writes for better sequential write traffic to storage severs. Meanwhile, TRIO coordinates the flushing orders among concurrent burst buffers to alleviate the contention on storage server bandwidth. Our experimental results reveal that TRIO can deliver 30.5% higher bandwidth and reduce the average job I/O time by 37% on average for data-intensive applications in various checkpointing scenarios.« less

Jupiter - Io In Front of Jupiter Turbulent Clouds

NASA Image and Video Library

1996-11-13

This photograph of the southern hemisphere of Jupiter was obtained by Voyager 2 on June 25, 1979, at a distance of 12 million kilometers (8 million miles). The Voyager spacecraft is rapidly nearing the giant planet, with closest approach to occur at 4:23 pm PDT on July 9. Seen in front of the turbulent clouds of the planet is Io, the innermost of the large Galilean satellites of Jupiter. Io is the size of our moon. Voyager discovered in early March that Io is the most volcanically active planetary body known in the solar system, with continuous eruptions much larger than any that take place on the Earth. The red, orange, and yellow colors of Io are thought to be deposits of sulfur and sulfur compounds produced in these eruptions. The smallest features in either Jupiter or Io that can be distinguished in this picture are about 200 kilometers (125 miles) across; this resolution, it is not yet possible to identify individual volcanic eruptions. Monitoring of the erupture activity of Io by Voyager 2 will begin about July 5 and will extend past the encounter July 9. http://photojournal.jpl.nasa.gov/catalog/PIA00371

Spatial Distribution of the Forbidden 1.707 mm Rovibronic Emission on Io

NASA Astrophysics Data System (ADS)

de Pater, Imke; de Kleer, Katherine; Adamkovics, Mate

2017-10-01

Io’s forbidden SO 1.707 mm rovibronic transition was discovered in 1999 when the satellite was observed with the NIRSPEC spectrometer on the Keck telescope while in eclipse [1]. The emission, at the time indicative of a rotational temperature of 1000 K, was attributed to SO molecules in the excited a1D state, ejected as such from the vent at a thermodynamic quenching temperature of ~1500 K. We suggested Loki as its source, a volcano that was exceptionally active during this period. In subsequent years we found that the disk-averaged SO emission varies substantially over time [2]. In November 2002 we observed Io in eclipse with Keck’s NIRSPEC coupled to the Adaptive Optics (AO) system, and identified a latitudinal variation in SO: most emission came from the equator and the south, and practically no emission was detected in the north [3]. To further investigate the nature of the SO emission, we observed Io in eclipse with the near-infrared integral field spectrograph OSIRIS, coupled to the AO system, on the Keck II telescope on UT 27 July 2010 and 25 December 2015. On the latter date we observed simultaneously with the NIRSPEC spectrometer at a high spectral resolution (R ~ 25,000). On these dates Callisto and Ganymede, resp., were close enough to be used for wavefront sensing. The angular resolution of our images is ~0.1”, or ~10 resolution elements across Io’s disk. The emission is extended; preliminary results show that in 2010 most of the emission originated in the north, and in 2015 it appeared to be more confined to the equatorial region. Potential connections to active volcanoes, or absence thereof, and model fits to the emission bands including LTE vs non-LTE contributions will be discussed. [1]: de Pater, I., et al., 2002. Icarus, 156, 296-301.[2]: Laver, C., et al. 2007. Icarus, 189, 401-408.[3]: de Pater, I. et al., 2007. Icarus, 191, 172-182.

A Practical Evaluation of a High-Security Energy-Efficient Gateway for IoT Fog Computing Applications

PubMed Central

Castedo, Luis

2017-01-01

Fog computing extends cloud computing to the edge of a network enabling new Internet of Things (IoT) applications and services, which may involve critical data that require privacy and security. In an IoT fog computing system, three elements can be distinguished: IoT nodes that collect data, the cloud, and interconnected IoT gateways that exchange messages with the IoT nodes and with the cloud. This article focuses on securing IoT gateways, which are assumed to be constrained in terms of computational resources, but that are able to offload some processing from the cloud and to reduce the latency in the responses to the IoT nodes. However, it is usually taken for granted that IoT gateways have direct access to the electrical grid, which is not always the case: in mission-critical applications like natural disaster relief or environmental monitoring, it is common to deploy IoT nodes and gateways in large areas where electricity comes from solar or wind energy that charge the batteries that power every device. In this article, how to secure IoT gateway communications while minimizing power consumption is analyzed. The throughput and power consumption of Rivest–Shamir–Adleman (RSA) and Elliptic Curve Cryptography (ECC) are considered, since they are really popular, but have not been thoroughly analyzed when applied to IoT scenarios. Moreover, the most widespread Transport Layer Security (TLS) cipher suites use RSA as the main public key-exchange algorithm, but the key sizes needed are not practical for most IoT devices and cannot be scaled to high security levels. In contrast, ECC represents a much lighter and scalable alternative. Thus, RSA and ECC are compared for equivalent security levels, and power consumption and data throughput are measured using a testbed of IoT gateways. The measurements obtained indicate that, in the specific fog computing scenario proposed, ECC is clearly a much better alternative than RSA, obtaining energy consumption reductions of up to 50% and a data throughput that doubles RSA in most scenarios. These conclusions are then corroborated by a frame temporal analysis of Ethernet packets. In addition, current data compression algorithms are evaluated, concluding that, when dealing with the small payloads related to IoT applications, they do not pay off in terms of real data throughput and power consumption. PMID:28850104

A Practical Evaluation of a High-Security Energy-Efficient Gateway for IoT Fog Computing Applications.

PubMed

Suárez-Albela, Manuel; Fernández-Caramés, Tiago M; Fraga-Lamas, Paula; Castedo, Luis

2017-08-29

Fog computing extends cloud computing to the edge of a network enabling new Internet of Things (IoT) applications and services, which may involve critical data that require privacy and security. In an IoT fog computing system, three elements can be distinguished: IoT nodes that collect data, the cloud, and interconnected IoT gateways that exchange messages with the IoT nodes and with the cloud. This article focuses on securing IoT gateways, which are assumed to be constrained in terms of computational resources, but that are able to offload some processing from the cloud and to reduce the latency in the responses to the IoT nodes. However, it is usually taken for granted that IoT gateways have direct access to the electrical grid, which is not always the case: in mission-critical applications like natural disaster relief or environmental monitoring, it is common to deploy IoT nodes and gateways in large areas where electricity comes from solar or wind energy that charge the batteries that power every device. In this article, how to secure IoT gateway communications while minimizing power consumption is analyzed. The throughput and power consumption of Rivest-Shamir-Adleman (RSA) and Elliptic Curve Cryptography (ECC) are considered, since they are really popular, but have not been thoroughly analyzed when applied to IoT scenarios. Moreover, the most widespread Transport Layer Security (TLS) cipher suites use RSA as the main public key-exchange algorithm, but the key sizes needed are not practical for most IoT devices and cannot be scaled to high security levels. In contrast, ECC represents a much lighter and scalable alternative. Thus, RSA and ECC are compared for equivalent security levels, and power consumption and data throughput are measured using a testbed of IoT gateways. The measurements obtained indicate that, in the specific fog computing scenario proposed, ECC is clearly a much better alternative than RSA, obtaining energy consumption reductions of up to 50% and a data throughput that doubles RSA in most scenarios. These conclusions are then corroborated by a frame temporal analysis of Ethernet packets. In addition, current data compression algorithms are evaluated, concluding that, when dealing with the small payloads related to IoT applications, they do not pay off in terms of real data throughput and power consumption.

Remote Monitoring of Soil Water Content, Temperature, and Heat Flow Using Low-Cost Cellular (3G) IoT Technology

NASA Astrophysics Data System (ADS)

Ham, J. M.

2016-12-01

New microprocessor boards, open-source sensors, and cloud infrastructure developed for the Internet of Things (IoT) can be used to create low-cost monitoring systems for environmental research. This project describes two applications in soil science and hydrology: 1) remote monitoring of the soil temperature regime near oil and gas operations to detect the thermal signature associated with the natural source zone degradation of hydrocarbon contaminants in the vadose zone, and 2) remote monitoring of soil water content near the surface as part of a global citizen science network. In both cases, prototype data collection systems were built around the cellular (2G/3G) "Electron" microcontroller (www.particle.io). This device allows connectivity to the cloud using a low-cost global SIM and data plan. The systems have cellular connectivity in over 100 countries and data can be logged to the cloud for storage. Users can view data real time over any internet connection or via their smart phone. For both projects, data logging, storage, and visualization was done using IoT services like Thingspeak (thingspeak.com). The soil thermal monitoring system was tested on experimental plots in Colorado USA to evaluate the accuracy and reliability of different temperature sensors and 3D printed housings. The soil water experiment included comparison opens-source capacitance-based sensors to commercial versions. Results demonstrate the power of leveraging IoT technology for field research.

Use of small stand-alone Internet nodes as a distributed control system

NASA Astrophysics Data System (ADS)

Goodwin, Robert W.; Kucera, Michael J.; Shea, Michael F.

1994-12-01

For several years, the standard model for accelerator control systems has been workstation consoles connected to VME local stations by a Local Area Network with analog and digital data being accessed via a field bus to custom I/O interface electronics. Commercially available hardware has now made it possible to implement a small stand-alone data acquisition station that combines the LAN connection, the computer, and the analog and digital I/O interface on a single board. This eliminates the complexity of a field bus and the associated proprietary I/O hardware. A minimum control system is one data acquisition station and a Macintosh or workstation console, both connected to the network; larger systems have more consoles and nodes. An implementation of this architecture is described along with performance and operational experience.

Characterizing parallel file-access patterns on a large-scale multiprocessor

NASA Technical Reports Server (NTRS)

Purakayastha, Apratim; Ellis, Carla Schlatter; Kotz, David; Nieuwejaar, Nils; Best, Michael

1994-01-01

Rapid increases in the computational speeds of multiprocessors have not been matched by corresponding performance enhancements in the I/O subsystem. To satisfy the large and growing I/O requirements of some parallel scientific applications, we need parallel file systems that can provide high-bandwidth and high-volume data transfer between the I/O subsystem and thousands of processors. Design of such high-performance parallel file systems depends on a thorough grasp of the expected workload. So far there have been no comprehensive usage studies of multiprocessor file systems. Our CHARISMA project intends to fill this void. The first results from our study involve an iPSC/860 at NASA Ames. This paper presents results from a different platform, the CM-5 at the National Center for Supercomputing Applications. The CHARISMA studies are unique because we collect information about every individual read and write request and about the entire mix of applications running on the machines. The results of our trace analysis lead to recommendations for parallel file system design. First the file system should support efficient concurrent access to many files, and I/O requests from many jobs under varying load conditions. Second, it must efficiently manage large files kept open for long periods. Third, it should expect to see small requests predominantly sequential access patterns, application-wide synchronous access, no concurrent file-sharing between jobs appreciable byte and block sharing between processes within jobs, and strong interprocess locality. Finally, the trace data suggest that node-level write caches and collective I/O request interfaces may be useful in certain environments.

I/O Performance Characterization of Lustre and NASA Applications on Pleiades

NASA Technical Reports Server (NTRS)

Saini, Subhash; Rappleye, Jason; Chang, Johnny; Barker, David Peter; Biswas, Rupak; Mehrotra, Piyush

2012-01-01

In this paper we study the performance of the Lustre file system using five scientific and engineering applications representative of NASA workload on large-scale supercomputing systems such as NASA s Pleiades. In order to facilitate the collection of Lustre performance metrics, we have developed a software tool that exports a wide variety of client and server-side metrics using SGI's Performance Co-Pilot (PCP), and generates a human readable report on key metrics at the end of a batch job. These performance metrics are (a) amount of data read and written, (b) number of files opened and closed, and (c) remote procedure call (RPC) size distribution (4 KB to 1024 KB, in powers of 2) for I/O operations. RPC size distribution measures the efficiency of the Lustre client and can pinpoint problems such as small write sizes, disk fragmentation, etc. These extracted statistics are useful in determining the I/O pattern of the application and can assist in identifying possible improvements for users applications. Information on the number of file operations enables a scientist to optimize the I/O performance of their applications. Amount of I/O data helps users choose the optimal stripe size and stripe count to enhance I/O performance. In this paper, we demonstrate the usefulness of this tool on Pleiades for five production quality NASA scientific and engineering applications. We compare the latency of read and write operations under Lustre to that with NFS by tracing system calls and signals. We also investigate the read and write policies and study the effect of page cache size on I/O operations. We examine the performance impact of Lustre stripe size and stripe count along with performance evaluation of file per process and single shared file accessed by all the processes for NASA workload using parameterized IOR benchmark.

High-Throughput and Low-Latency Network Communication with NetIO

NASA Astrophysics Data System (ADS)

Schumacher, Jörn; Plessl, Christian; Vandelli, Wainer

2017-10-01

HPC network technologies like Infiniband, TrueScale or OmniPath provide low- latency and high-throughput communication between hosts, which makes them attractive options for data-acquisition systems in large-scale high-energy physics experiments. Like HPC networks, DAQ networks are local and include a well specified number of systems. Unfortunately traditional network communication APIs for HPC clusters like MPI or PGAS exclusively target the HPC community and are not suited well for DAQ applications. It is possible to build distributed DAQ applications using low-level system APIs like Infiniband Verbs, but it requires a non-negligible effort and expert knowledge. At the same time, message services like ZeroMQ have gained popularity in the HEP community. They make it possible to build distributed applications with a high-level approach and provide good performance. Unfortunately, their usage usually limits developers to TCP/IP- based networks. While it is possible to operate a TCP/IP stack on top of Infiniband and OmniPath, this approach may not be very efficient compared to a direct use of native APIs. NetIO is a simple, novel asynchronous message service that can operate on Ethernet, Infiniband and similar network fabrics. In this paper the design and implementation of NetIO is presented and described, and its use is evaluated in comparison to other approaches. NetIO supports different high-level programming models and typical workloads of HEP applications. The ATLAS FELIX project [1] successfully uses NetIO as its central communication platform. The architecture of NetIO is described in this paper, including the user-level API and the internal data-flow design. The paper includes a performance evaluation of NetIO including throughput and latency measurements. The performance is compared against the state-of-the- art ZeroMQ message service. Performance measurements are performed in a lab environment with Ethernet and FDR Infiniband networks.

Single event induced transients in I/O devices - A characterization

NASA Technical Reports Server (NTRS)

Newberry, D. M.; Kaye, D. H.; Soli, G. A.

1990-01-01

The results of single-event upset (SEU) testing performed to evaluate the parametric transients, i.e., amplitude and duration, in several I/O devices, and the impact of these transients are discussed. The failure rate of these devices is dependent on the susceptibility of interconnected devices to the resulting transient change in the output of the I/O device. This failure rate, which is a function of the susceptibility of the interconnected device as well as the SEU response of the I/O device itself, may be significantly different from an upset rate calculated without taking these factors into account. The impact at the system level is discussed by way of an example.

The Prospect of Internet of Things and Big Data Analytics in Transportation System

NASA Astrophysics Data System (ADS)

Noori Hussein, Waleed; Kamarudin, L. M.; Hussain, Haider N.; Zakaria, A.; Badlishah Ahmed, R.; Zahri, N. A. H.

2018-05-01

Internet of Things (IoT); the new dawn technology that describes how data, people and interconnected physical objects act based on communicated information, and big data analytics have been adopted by diverse domains for varying purposes. Manufacturing, agriculture, banks, oil and gas, healthcare, retail, hospitality, and food services are few of the sectors that have adopted and massively utilized IoT and big data analytics. The transportation industry is also an early adopter, with significant attendant effects on its processes of tracking shipment, freight monitoring, and transparent warehousing. This is recorded in countries like England, Singapore, Portugal, and Germany, while Malaysia is currently assessing the potentials and researching a purpose-driven adoption and implementation. This paper, based on review of related literature, presents a summary of the inherent prospects in adopting IoT and big data analytics in the Malaysia transportation system. Efficient and safe port environment, predictive maintenance and remote management, boundary-less software platform and connected ecosystem, among others, are the inherent benefits in the IoT and big data analytics for the Malaysia transportation system.

Programmable DMA controller

NASA Technical Reports Server (NTRS)

Hendry, David F. (Inventor)

1993-01-01

In a data system having a memory, plural input/output (I/O) devices and a bus connecting each of the I/O devices to the memory, a direct memory access (DMA) controller regulating access of each of the I/O devices to the bus, including a priority register storing priorities of bus access requests from the I/O devices, an interrupt register storing bus access requests of the I/O devices, a resolver for selecting one of the I/O devices to have access to the bus, a pointer register storing addresses of locations in the memory for communication with the one I/O device via the bus, a sequence register storing an address of a location in the memory containing a channel program instruction which is to be executed next, an ALU for incrementing and decrementing addresses stored in the pointer register, computing the next address to be stored in the sequence register, computing an initial contents of each of the register. The memory contains a sequence of channel program instructions defining a set up operation wherein the contents of each of the registers in the channel register is initialized in accordance with the initial contents computed by the ALU and an access operation wherein data is transferred on the bus between a location in the memory whose address is currently stored in the pointer register and the one I/O device enabled by the resolver.

QoS support for end users of I/O-intensive applications using shared storage systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, Marion Kei; Zhang, Xuechen; Jiang, Song

2011-01-19

I/O-intensive applications are becoming increasingly common on today's high-performance computing systems. While performance of compute-bound applications can be effectively guaranteed with techniques such as space sharing or QoS-aware process scheduling, it remains a challenge to meet QoS requirements for end users of I/O-intensive applications using shared storage systems because it is difficult to differentiate I/O services for different applications with individual quality requirements. Furthermore, it is difficult for end users to accurately specify performance goals to the storage system using I/O-related metrics such as request latency or throughput. As access patterns, request rates, and the system workload change in time,more » a fixed I/O performance goal, such as bounds on throughput or latency, can be expensive to achieve and may not lead to a meaningful performance guarantees such as bounded program execution time. We propose a scheme supporting end-users QoS goals, specified in terms of program execution time, in shared storage environments. We automatically translate the users performance goals into instantaneous I/O throughput bounds using a machine learning technique, and use dynamically determined service time windows to efficiently meet the throughput bounds. We have implemented this scheme in the PVFS2 parallel file system and have conducted an extensive evaluation. Our results show that this scheme can satisfy realistic end-user QoS requirements by making highly efficient use of the I/O resources. The scheme seeks to balance programs attainment of QoS requirements, and saves as much of the remaining I/O capacity as possible for best-effort programs.« less

IoSiS: a radar system for imaging of satellites in space

NASA Astrophysics Data System (ADS)

Jirousek, M.; Anger, S.; Dill, S.; Schreiber, E.; Peichl, M.

2017-05-01

Space debris nowadays is one of the main threats for satellite systems especially in low earth orbit (LEO). More than 700,000 debris objects with potential to destroy or damage a satellite are estimated. The effects of an impact often are not identifiable directly from ground. High-resolution radar images are helpful in analyzing a possible damage. Therefor DLR is currently developing a radar system called IoSiS (Imaging of Satellites in Space), being based on an existing steering antenna structure and our multi-purpose high-performance radar system GigaRad for experimental investigations. GigaRad is a multi-channel system operating at X band and using a bandwidth of up to 4.4 GHz in the IoSiS configuration, providing fully separated transmit (TX) and receive (RX) channels, and separated antennas. For the observation of small satellites or space debris a highpower traveling-wave-tube amplifier (TWTA) is mounted close to the TX antenna feed. For the experimental phase IoSiS uses a 9 m TX and a 1 m RX antenna mounted on a common steerable positioner. High-resolution radar images are obtained by using Inverse Synthetic Aperture Radar (ISAR) techniques. The guided tracking of known objects during overpass allows here wide azimuth observation angles. Thus high azimuth resolution comparable to the range resolution can be achieved. This paper outlines technical main characteristics of the IoSiS radar system including the basic setup of the antenna, the radar instrument with the RF error correction, and the measurement strategy. Also a short description about a simulation tool for the whole instrument and expected images is shown.

Semantic Framework of Internet of Things for Smart Cities: Case Studies.

PubMed

Zhang, Ningyu; Chen, Huajun; Chen, Xi; Chen, Jiaoyan

2016-09-14

In recent years, the advancement of sensor technology has led to the generation of heterogeneous Internet-of-Things (IoT) data by smart cities. Thus, the development and deployment of various aspects of IoT-based applications are necessary to mine the potential value of data to the benefit of people and their lives. However, the variety, volume, heterogeneity, and real-time nature of data obtained from smart cities pose considerable challenges. In this paper, we propose a semantic framework that integrates the IoT with machine learning for smart cities. The proposed framework retrieves and models urban data for certain kinds of IoT applications based on semantic and machine-learning technologies. Moreover, we propose two case studies: pollution detection from vehicles and traffic pattern detection. The experimental results show that our system is scalable and capable of accommodating a large number of urban regions with different types of IoT applications.

A study of internet of things real-time data updating based on WebSocket

NASA Astrophysics Data System (ADS)

Wei, Shoulin; Yu, Konglin; Dai, Wei; Liang, Bo; Zhang, Xiaoli

2015-12-01

The Internet of Things (IoT) is gradually entering the industrial stage. Web applications in IoT such as monitoring, instant messaging, real-time quote system changes need to be transmitted in real-time mode to client without client constantly refreshing and sending the request. These applications often need to be as fast as possible and provide nearly real-time components. Real-time data updating is becoming the core part of application layer visualization technology in IoT. With support of data push in server-side, running state of "Things" in IoT could be displayed in real-time mode. This paper discusses several current real-time data updating method and explores the advantages and disadvantages of each method. We explore the use of WebSocket in a new approach for real-time data updating in IoT, since WebSocket provides low delay, low network throughput solutions for full-duplex communication.

Semantic Framework of Internet of Things for Smart Cities: Case Studies

PubMed Central

Zhang, Ningyu; Chen, Huajun; Chen, Xi; Chen, Jiaoyan

2016-01-01

In recent years, the advancement of sensor technology has led to the generation of heterogeneous Internet-of-Things (IoT) data by smart cities. Thus, the development and deployment of various aspects of IoT-based applications are necessary to mine the potential value of data to the benefit of people and their lives. However, the variety, volume, heterogeneity, and real-time nature of data obtained from smart cities pose considerable challenges. In this paper, we propose a semantic framework that integrates the IoT with machine learning for smart cities. The proposed framework retrieves and models urban data for certain kinds of IoT applications based on semantic and machine-learning technologies. Moreover, we propose two case studies: pollution detection from vehicles and traffic pattern detection. The experimental results show that our system is scalable and capable of accommodating a large number of urban regions with different types of IoT applications. PMID:27649185

Research and design of smart grid monitoring control via terminal based on iOS system

NASA Astrophysics Data System (ADS)

Fu, Wei; Gong, Li; Chen, Heli; Pan, Guangji

2017-06-01

Aiming at a series of problems existing in current smart grid monitoring Control Terminal, such as high costs, poor portability, simple monitoring system, poor software extensions, low system reliability when transmitting information, single man-machine interface, poor security, etc., smart grid remote monitoring system based on the iOS system has been designed. The system interacts with smart grid server so that it can acquire grid data through WiFi/3G/4G networks, and monitor each grid line running status, as well as power plant equipment operating conditions. When it occurs an exception in the power plant, incident information can be sent to the user iOS terminal equipment timely, which will provide troubleshooting information to help the grid staff to make the right decisions in a timely manner, to avoid further accidents. Field tests have shown the system realizes the integrated grid monitoring functions, low maintenance cost, friendly interface, high security and reliability, and it possesses certain applicable value.

An IoT-cloud Based Wearable ECG Monitoring System for Smart Healthcare.

PubMed

Yang, Zhe; Zhou, Qihao; Lei, Lei; Zheng, Kan; Xiang, Wei

2016-12-01

Public healthcare has been paid an increasing attention given the exponential growth human population and medical expenses. It is well known that an effective health monitoring system can detect abnormalities of health conditions in time and make diagnoses according to the gleaned data. As a vital approach to diagnose heart diseases, ECG monitoring is widely studied and applied. However, nearly all existing portable ECG monitoring systems cannot work without a mobile application, which is responsible for data collection and display. In this paper, we propose a new method for ECG monitoring based on Internet-of-Things (IoT) techniques. ECG data are gathered using a wearable monitoring node and are transmitted directly to the IoT cloud using Wi-Fi. Both the HTTP and MQTT protocols are employed in the IoT cloud in order to provide visual and timely ECG data to users. Nearly all smart terminals with a web browser can acquire ECG data conveniently, which has greatly alleviated the cross-platform issue. Experiments are carried out on healthy volunteers in order to verify the reliability of the entire system. Experimental results reveal that the proposed system is reliable in collecting and displaying real-time ECG data, which can aid in the primary diagnosis of certain heart diseases.

An Information Theoretical Analysis of Human Insulin-Glucose System Toward the Internet of Bio-Nano Things.

PubMed

Abbasi, Naveed A; Akan, Ozgur B

2017-12-01

Molecular communication is an important tool to understand biological communications with many promising applications in Internet of Bio-Nano Things (IoBNT). The insulin-glucose system is of key significance among the major intra-body nanonetworks, since it fulfills metabolic requirements of the body. The study of biological networks from information and communication theoretical (ICT) perspective is necessary for their introduction in the IoBNT framework. Therefore, the objective of this paper is to provide and analyze for the first time in the literature, a simple molecular communication model of the human insulin-glucose system from ICT perspective. The data rate, channel capacity, and the group propagation delay are analyzed for a two-cell network between a pancreatic beta cell and a muscle cell that are connected through a capillary. The results point out a correlation between an increase in insulin resistance and a decrease in the data rate and channel capacity, an increase in the insulin transmission rate, and an increase in the propagation delay. We also propose applications for the introduction of the system in the IoBNT framework. Multi-cell insulin glucose system models may be based on this simple model to help in the investigation, diagnosis, and treatment of insulin resistance by means of novel IoBNT applications.

Device Centric Throughput and QoS Optimization for IoTsin a Smart Building Using CRN-Techniques

PubMed Central

Aslam, Saleem; Hasan, Najam Ul; Shahid, Adnan; Jang, Ju Wook; Lee, Kyung-Geun

2016-01-01

The Internet of Things (IoT) has gained an incredible importance in the communication and networking industry due to its innovative solutions and advantages in diverse domains. The IoT’ network is a network of smart physical objects: devices, vehicles, buildings, etc. The IoT has a number of applications ranging from smart home, smart surveillance to smart healthcare systems. Since IoT consists of various heterogeneous devices that exhibit different traffic patterns and expect different quality of service (QoS) in terms of data rate, bit error rate and the stability index of the channel, therefore, in this paper, we formulated an optimization problem to assign channels to heterogeneous IoT devices within a smart building for the provisioning of their desired QoS. To solve this problem, a novel particle swarm optimization-based algorithm is proposed. Then, exhaustive simulations are carried out to evaluate the performance of the proposed algorithm. Simulation results demonstrate the supremacy of our proposed algorithm over the existing ones in terms of throughput, bit error rate and the stability index of the channel. PMID:27782057

High-temperature hot spots on Io as seen by the Galileo solid state imaging (SSI) experiment

USGS Publications Warehouse

McEwen, A.S.; Simonelli, D.P.; Senske, D.R.; Klaasen, K.P.; Keszthelyi, L.; Johnson, T.V.; Geissler, P.E.; Carr, M.H.; Belton, M.J.S.

1997-01-01

High-temperature hot spots on Io have been imaged at ???50 km spatial resolution by Galileo's CCD imaging system (SSI). Images were acquired during eclipses (Io in Jupiter's shadow) via the SSI clear filter (???0.4-1.0 ??m), detecting emissions from both small intense hot spots and diffuse extended glows associated with Io's atmosphere and plumes. A total of 13 hot spots have been detected over ???70% of Io's surface. Each hot spot falls precisely on a low-albedo feature corresponding to a caldera floor and/or lava flow. The hot-spot temperatures must exceed ???700 K for detection by SSI. Observations at wavelengths longer than those available to SSI require that most of these hot spots actually have significantly higher temperatures (???1000 K or higher) and cover small areas. The high-temperature hot spots probably mark the locations of active silicate volcanism, supporting suggestions that the eruption and near-surface movement of silicate magma drives the heat flow and volcanic activity of Io. Copyright 1997 by the American Geophysical Union.

Reverse Engineering and Security Evaluation of Commercial Tags for RFID-Based IoT Applications.

PubMed

Fernández-Caramés, Tiago M; Fraga-Lamas, Paula; Suárez-Albela, Manuel; Castedo, Luis

2016-12-24

The Internet of Things (IoT) is a distributed system of physical objects that requires the seamless integration of hardware (e.g., sensors, actuators, electronics) and network communications in order to collect and exchange data. IoT smart objects need to be somehow identified to determine the origin of the data and to automatically detect the elements around us. One of the best positioned technologies to perform identification is RFID (Radio Frequency Identification), which in the last years has gained a lot of popularity in applications like access control, payment cards or logistics. Despite its popularity, RFID security has not been properly handled in numerous applications. To foster security in such applications, this article includes three main contributions. First, in order to establish the basics, a detailed review of the most common flaws found in RFID-based IoT systems is provided, including the latest attacks described in the literature. Second, a novel methodology that eases the detection and mitigation of such flaws is presented. Third, the latest RFID security tools are analyzed and the methodology proposed is applied through one of them (Proxmark 3) to validate it. Thus, the methodology is tested in different scenarios where tags are commonly used for identification. In such systems it was possible to clone transponders, extract information, and even emulate both tags and readers. Therefore, it is shown that the methodology proposed is useful for auditing security and reverse engineering RFID communications in IoT applications. It must be noted that, although this paper is aimed at fostering RFID communications security in IoT applications, the methodology can be applied to any RFID communications protocol.

Reverse Engineering and Security Evaluation of Commercial Tags for RFID-Based IoT Applications

PubMed Central

Fernández-Caramés, Tiago M.; Fraga-Lamas, Paula; Suárez-Albela, Manuel; Castedo, Luis

2016-01-01

The Internet of Things (IoT) is a distributed system of physical objects that requires the seamless integration of hardware (e.g., sensors, actuators, electronics) and network communications in order to collect and exchange data. IoT smart objects need to be somehow identified to determine the origin of the data and to automatically detect the elements around us. One of the best positioned technologies to perform identification is RFID (Radio Frequency Identification), which in the last years has gained a lot of popularity in applications like access control, payment cards or logistics. Despite its popularity, RFID security has not been properly handled in numerous applications. To foster security in such applications, this article includes three main contributions. First, in order to establish the basics, a detailed review of the most common flaws found in RFID-based IoT systems is provided, including the latest attacks described in the literature. Second, a novel methodology that eases the detection and mitigation of such flaws is presented. Third, the latest RFID security tools are analyzed and the methodology proposed is applied through one of them (Proxmark 3) to validate it. Thus, the methodology is tested in different scenarios where tags are commonly used for identification. In such systems it was possible to clone transponders, extract information, and even emulate both tags and readers. Therefore, it is shown that the methodology proposed is useful for auditing security and reverse engineering RFID communications in IoT applications. It must be noted that, although this paper is aimed at fostering RFID communications security in IoT applications, the methodology can be applied to any RFID communications protocol. PMID:28029119

Rapid and equivalent systemic bioavailability of the antidotes HI-6 and dicobalt edetate via the intraosseous and intravenous routes.

PubMed

Hill, Simon L; Thomas, Simon H L; Flecknell, Paul A; Thomas, Aurelie A; Morris, Chris M; Henderson, David; Dunn, Michael; Blain, Peter G

2015-08-01

Rapid and effective administration of antidotes by emergency medical responders is needed to improve the survival of patients severely poisoned after deliberate release of chemical weapons, but intravenous access is difficult to obtain while wearing personal protective equipment and in casualties with circulatory collapse. To test the hypothesis that rapid and substantial bioavailability of the antidotes HI-6 oxime and dicobalt edetate can be achieved via the intraosseous (IO) route, plasma concentration-time profiles of these antidotes were compared after administration by the intravenous and IO routes in a minipig animal model. 12 male Göttingen minipigs were randomly allocated to receive 7.14 mg/kg of HI-6 (by rapid bolus) then 4.28 mg/kg of dicobalt edetate (over 1 min) via the intravenous or IO route. Plasma concentrations of each antidote were measured over 360 min following administration and plasma concentration-time profiles plotted for each drug by each route. Peak HI-6 and cobalt concentrations occurred within 2 min of administration by both the intravenous and IO routes. Mean areas under the concentration-time curves (SD) to the end of the experiment (area under the concentration-time curve, AUC (0-t)) for cobalt were 430 (47, intravenous) and 445 (40, IO) μg-min/mL (mean difference 15, 95% CI -41 to 70, p=0.568) and for HI-6 were 2739 (1038, intravenous) and 2772 (1629, IO) μg-min/mL (mean difference 0.33, 95% CI -1724 to 1790, p=0.97). Increases in heart rate (by 50 beats/min intravenous and 27 beats/min IO) and BP, (by 67/58 mm Hg intravenous and 78/59 mm Hg IO), were observed after dicobalt edetate, consistent with the known adverse effects of this antidote. This study demonstrates rapid and similar systemic bioavailability of HI-6 and dicobalt edetate when given by the IO and intravenous routes. IO delivery of these antidotes is appropriate in the acute management of patients with organophosphate and cyanide intoxication when the intravenous route is impractical. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Effects of Iron Overload on the Bone Marrow Microenvironment in Mice

PubMed Central

Zhao, Mingfeng; Li, Deguan; Chai, Xiao; Cao, Xiaoli; Meng, Juanxia; Chen, Jie; Xiao, Xia; Li, Qing; Mu, Juan; Shen, Jichun; Meng, Aimin

2015-01-01

Objective Using a mouse model, Iron Overload (IO) induced bone marrow microenvironment injury was investigated, focusing on the involvement of reactive oxygen species (ROS). Methods Mice were intraperitoneally injected with iron dextran (12.5, 25, or 50mg) every three days for two, four, and six week durations. Deferasirox(DFX)125mg/ml and N-acetyl-L-cysteine (NAC) 40mM were co-administered. Then, bone marrow derived mesenchymal stem cells (BM-MSCs) were isolated and assessed for proliferation and differentiation ability, as well as related gene changes. Immunohistochemical analysis assessed the expression of haematopoietic chemokines. Supporting functions of BM-MSCs were studied by co-culture system. Results In IO condition (25mg/ml for 4 weeks), BM-MSCs exhibited proliferation deficiencies and unbalanced osteogenic/adipogenic differentiation. The IO BM-MSCs showed a longer double time (2.07±0.14 days) than control (1.03±0.07 days) (P<0.05). The immunohistochemical analysis demonstrated that chemokine stromal cell-derived factor-1, stem cell factor -1, and vascular endothelial growth factor-1 expression were decreased. The co-cultured system demonstrated that bone marrow mononuclear cells (BMMNCs) co-cultured with IO BM-MSCs had decreased colony forming unit (CFU) count (p<0.01), which indicates IO could lead to decreased hematopoietic supporting functions of BM-MSCs. This effect was associated with elevated phosphatidylinositol 3 kinase (PI3K) and reduced of Forkhead box protein O3 (FOXO3) mRNA expression, which could induce the generation of ROS. Results also demonstrated that NAC or DFX treatment could partially attenuate cell injury and inhibit signaling pathway striggered by IO. Conclusion These results demonstrated that IO can impair the bone marrow microenvironment, including the quantity and quality of BM-MSCs. PMID:25774923

Feasibility of Juno radio occultations of the Io plasma torus

NASA Astrophysics Data System (ADS)

Phipps, P. H.; Withers, P.

2016-12-01

Jupiter's magnetosphere is driven by internally produced plasma. The innermost Galilean satellite, Io, isthe dominant source of this plasma. Volcanoes on Io's surface create an atmosphere of sulfur and oxygenwhich escapes into Jupiter's magnetosphere and becomes ionized. This ionized material is trapped byJupiter's magnetic field and creates a torus of plasma centered at Io's orbital radius, called the Io plasmatorus. This torus is divided into three regions distinct in both density and composition. Densities in thistorus can be probed by spacecraft via radio occultations. A radio occultation occurs when plasma comesbetween a spacecraft and a receiver during a time when the spacecraft is sending a radio signal. The Junospacecraft, which arrived in orbit around Jupiter in July 2016, is in an orbit which will be ideal forperforming radio occultations of the Io plasma torus. We test the feasibility of using thetelecommunications system on the Juno spacecraft to perform a radio occultation. Io plasma torusdensities derived from Voyager 1 data are used in creating a model torus. Using the Ka and X-band radiofrequencies we derive vertical profiles for the total electron content of the modeled Io plasma torus. AMarkov Chain Monte Carlo fit is performed on the derived profiles to extract, for each of the torusregions, the scale height and peak total electron content. The scale height can be used to derive atemperature for the torus while the peak total electron content can be used to derive the peak electrondensity. We show that Juno radio occultation measurements of the Io plasma torus are feasible andscientifically valuable.

Smart mobility solution with multiple input Output interface.

PubMed

Sethi, Aartika; Deb, Sujay; Ranjan, Prabhat; Sardar, Arghya

2017-07-01

Smart wheelchairs are commonly used to provide solution for mobility impairment. However their usage is limited primarily due to high cost owing from sensors required for giving input, lack of adaptability for different categories of input and limited functionality. In this paper we propose a smart mobility solution using smartphone with inbuilt sensors (accelerometer, camera and speaker) as an input interface. An Emotiv EPOC+ is also used for motor imagery based input control synced with facial expressions in cases of extreme disability. Apart from traction, additional functions like home security and automation are provided using Internet of Things (IoT) and web interfaces. Although preliminary, our results suggest that this system can be used as an integrated and efficient solution for people suffering from mobility impairment. The results also indicate a decent accuracy is obtained for the overall system.

Volcanogenic Sulfur on Earth and Io: Composition and Spectroscopy

USGS Publications Warehouse

Kargel, J.S.; Delmelle, P.; Nash, D.B.

1999-01-01

The causes of Io's variegated surface, especially the roles of sulfur, and the geochemical history of sulfur compounds on Io are not well understood. Suspecting that minor impurities in sulfur might be important, we have investigated the major and trace element chemistry and spectroscopic reflectance of natural sulfur from a variety of terrestrial volcanic-hydrothermal environments. Evidence suggests that Io may be substantially coated with impure sulfur. On Earth, a few tenths of a percent to a few percent of chalcophile trace elements (e.g., As and Se) comonly occur in sulfur and appear to stabilize material of yellow, brown, orange, and red hues, which may persist even at low temperatures. Percentage levels of chalcophile impurities are reasonably expected to occur on Io in vapor sublimate deposits and flows derived from such deposits. Such impurities join a host of other mechanisms that might explain Io's reds and yellows. Two-tenths to two percent opaque crystalline impurities, particularly pyrite (FeS2), commonly produces green, gray, and black volcanic sulfur on Earth and might explain areas of Io having deposits of these colors. Pyrite produces a broad absorption near 1 ??m that gradually diminishes out to 1.6 ??m - similar but not identical to the spectrum of Io seen in Galileo NIMS data. Percentage amounts of carbonaceous impurities and tens of percent SiO2 (as silicates) also strongly affect the spectral properties of Earth's sulfur. Io's broad absorption between 0.52 and 0.64 ??m remains unexplained by these data but could be due to sodium sulfides, as suggested previously by others, or to As, Se, or other impurities. These impurities and others, such as P and Cl (which could exist on Io's surface in amounts over 1% that of sulfur), greatly alter the molecular structure of molten and solid sulfur. Minor impurities could impact Io's geology, such as the morphology of sulfur lava flows and the ability of sulfur to sustain high relief. We have not found any natural sulfur containing significant Na beyond that attributable to silicate inclusions. In sum, the unique physical-chemical properties of S-rich systems and the strong affinity of certain elements for S may have broad implications for the appearance, spectroscopic interpretation, and geologic processes of Io. Identification of impurities in sulfur may be helpful in tracing the geochemical evolution of surface deposits on Io. Perhaps foretelling of new areas of investigation, Cl has recently been reported in the Io torus (M. Kueppers and N. M. Schneider 1999, Eos Trans.80, 5207), suggesting the presence on Io of either salts, such as halite, or sulfur chlorides. Further evidence of minor iogenic impurities should be sought in Io's neutral cloud and plasma torus as well as in further scrutiny of Io's reflectance spectra. ?? 1999 Academic Press.

Parameter identification for nonlinear aerodynamic systems

NASA Technical Reports Server (NTRS)

Pearson, Allan E.

1990-01-01

Parameter identification for nonlinear aerodynamic systems is examined. It is presumed that the underlying model can be arranged into an input/output (I/O) differential operator equation of a generic form. The algorithm estimation is especially efficient since the equation error can be integrated exactly given any I/O pair to obtain an algebraic function of the parameters. The algorithm for parameter identification was extended to the order determination problem for linear differential system. The degeneracy in a least squares estimate caused by feedback was addressed. A method of frequency analysis for determining the transfer function G(j omega) from transient I/O data was formulated using complex valued Fourier based modulating functions in contrast with the trigonometric modulating functions for the parameter estimation problem. A simulation result of applying the algorithm is given under noise-free conditions for a system with a low pass transfer function.

Dynamic file-access characteristics of a production parallel scientific workload

NASA Technical Reports Server (NTRS)

Kotz, David; Nieuwejaar, Nils

1994-01-01

Multiprocessors have permitted astounding increases in computational performance, but many cannot meet the intense I/O requirements of some scientific applications. An important component of any solution to this I/O bottleneck is a parallel file system that can provide high-bandwidth access to tremendous amounts of data in parallel to hundreds or thousands of processors. Most successful systems are based on a solid understanding of the expected workload, but thus far there have been no comprehensive workload characterizations of multiprocessor file systems. This paper presents the results of a three week tracing study in which all file-related activity on a massively parallel computer was recorded. Our instrumentation differs from previous efforts in that it collects information about every I/O request and about the mix of jobs running in a production environment. We also present the results of a trace-driven caching simulation and recommendations for designers of multiprocessor file systems.

Characterizing output bottlenecks in a supercomputer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Bing; Chase, Jeffrey; Dillow, David A

2012-01-01

Supercomputer I/O loads are often dominated by writes. HPC (High Performance Computing) file systems are designed to absorb these bursty outputs at high bandwidth through massive parallelism. However, the delivered write bandwidth often falls well below the peak. This paper characterizes the data absorption behavior of a center-wide shared Lustre parallel file system on the Jaguar supercomputer. We use a statistical methodology to address the challenges of accurately measuring a shared machine under production load and to obtain the distribution of bandwidth across samples of compute nodes, storage targets, and time intervals. We observe and quantify limitations from competing traffic,more » contention on storage servers and I/O routers, concurrency limitations in the client compute node operating systems, and the impact of variance (stragglers) on coupled output such as striping. We then examine the implications of our results for application performance and the design of I/O middleware systems on shared supercomputers.« less

IoT-based flood embankments monitoring system

NASA Astrophysics Data System (ADS)

Michta, E.; Szulim, R.; Sojka-Piotrowska, A.; Piotrowski, K.

2017-08-01

In the paper a concept of flood embankments monitoring system based on using Internet of Things approach and Cloud Computing technologies will be presented. The proposed system consists of sensors, IoT nodes, Gateways and Cloud based services. Nodes communicates with the sensors measuring certain physical parameters describing the state of the embankments and communicates with the Gateways. Gateways are specialized active devices responsible for direct communication with the nodes, collecting sensor data, preprocess the data, applying local rules and communicate with the Cloud Services using communication API delivered by cloud services providers. Architecture of all of the system components will be proposed consisting IoT devices functionalities description, their communication model, software modules and services bases on using a public cloud computing platform like Microsoft Azure will be proposed. The most important aspects of maintaining the communication in a secure way will be shown.

I/O routing in a multidimensional torus network

DOEpatents

Chen, Dong; Eisley, Noel A.; Heidelberger, Philip

2017-02-07

A method, system and computer program product are disclosed for routing data packet in a computing system comprising a multidimensional torus compute node network including a multitude of compute nodes, and an I/O node network including a plurality of I/O nodes. In one embodiment, the method comprises assigning to each of the data packets a destination address identifying one of the compute nodes; providing each of the data packets with a toio value; routing the data packets through the compute node network to the destination addresses of the data packets; and when each of the data packets reaches the destination address assigned to said each data packet, routing said each data packet to one of the I/O nodes if the toio value of said each data packet is a specified value. In one embodiment, each of the data packets is also provided with an ioreturn value used to route the data packets through the compute node network.

I/O routing in a multidimensional torus network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Eisley, Noel A.; Heidelberger, Philip

A method, system and computer program product are disclosed for routing data packet in a computing system comprising a multidimensional torus compute node network including a multitude of compute nodes, and an I/O node network including a plurality of I/O nodes. In one embodiment, the method comprises assigning to each of the data packets a destination address identifying one of the compute nodes; providing each of the data packets with a toio value; routing the data packets through the compute node network to the destination addresses of the data packets; and when each of the data packets reaches the destinationmore » address assigned to said each data packet, routing said each data packet to one of the I/O nodes if the toio value of said each data packet is a specified value. In one embodiment, each of the data packets is also provided with an ioreturn value used to route the data packets through the compute node network.« less

Energy-Aware Computation Offloading of IoT Sensors in Cloudlet-Based Mobile Edge Computing.

PubMed

Ma, Xiao; Lin, Chuang; Zhang, Han; Liu, Jianwei

2018-06-15

Mobile edge computing is proposed as a promising computing paradigm to relieve the excessive burden of data centers and mobile networks, which is induced by the rapid growth of Internet of Things (IoT). This work introduces the cloud-assisted multi-cloudlet framework to provision scalable services in cloudlet-based mobile edge computing. Due to the constrained computation resources of cloudlets and limited communication resources of wireless access points (APs), IoT sensors with identical computation offloading decisions interact with each other. To optimize the processing delay and energy consumption of computation tasks, theoretic analysis of the computation offloading decision problem of IoT sensors is presented in this paper. In more detail, the computation offloading decision problem of IoT sensors is formulated as a computation offloading game and the condition of Nash equilibrium is derived by introducing the tool of a potential game. By exploiting the finite improvement property of the game, the Computation Offloading Decision (COD) algorithm is designed to provide decentralized computation offloading strategies for IoT sensors. Simulation results demonstrate that the COD algorithm can significantly reduce the system cost compared with the random-selection algorithm and the cloud-first algorithm. Furthermore, the COD algorithm can scale well with increasing IoT sensors.

Thermal Emission Variability of Zamama, Culann and Tupan on Io Using Galileo Near-Infrared Mapping Spectrometer (NIMS) Data

NASA Technical Reports Server (NTRS)

Ennis, M. E.; Davies, A. G.

2005-01-01

The Jovian satellite Io is the most volcanically active body in the Solar System. Previous analyses [e.g., 1-4] indicate the presence of high-temperature silicate volcanism on Io, similar to silicate volcanism occurring on Earth. Instruments onboard the Galileo spacecraft, especially the Near Infrared Mapping Spectrometer (NIMS) and the Solid State Imager (SSI), provided much data of Io s active volcanoes throughout the duration of the Galileo mission (June 1996-September 2003). NIMS data is particularly sensitive to thermal emission from active and cooling lava over cooling times of seconds to a few years. The objective of this ongoing study of Io s volcanism is to determine the variability of thermal emission from volcanoes on Io s surface, in order to better understand the styles of eruption, and to constrain the volumes of material erupted. Ultimately, this will help to constrain the contribution of active volcanism to Io s thermal budget. Data have been analyzed for the volcano Zamama, located at 173 W, 21 N, and the power output of Zamama, the volumes of lava being erupted, and the eruption rate determined. Culann and Tupan have also been analysed in this way. This abstract primarily concentrates on Zamama.

Using Internet of Things technologies for wireless sensor networks

NASA Astrophysics Data System (ADS)

Martinez, K.; Hart, J. K.; Basford, P. J.; Bragg, G. M.; Ward, T.

2013-12-01

Numerous authors have envisioned the future internet where anything will be connected: the Internet of Things (IoT). The idea is an extrapolation of the spread of networked devices such as phones, tablets etc. Each device is expected to have its own Internet address and thus be easy to access. The key building blocks of any IoT system are networking, hardware platforms and node software - so they are similar to wireless sensor network requirements. Most existing IoT demonstrators and applications have been gadget-style objects where power and connectivity problems are not too restricting. Environmental sensor networks can benefit from using some of the technologies involved in IoT development. However it is expected that tuning the networking and power management will be necessary to make them as efficient as state of the art wireless sensor networks. Some IoT assumptions such as always-connected nodes and full IP capability need to be considered. This paper will illustrate the advantages and disadvantages of IoT techniques for environment sensing drawing on a range of employment scenarios. We also describe a glacial 'Internet of things' project, which aims to monitor glacial processes. In particular we describe the IoT developments in a deployment in Iceland to examine glacier seismicity, velocity and provide camera images.

Io - Volcanic Eruption

NASA Technical Reports Server (NTRS)

1979-01-01

This photo of a volcanic eruption on Jupiter's satellite Io (dark fountain-like feature near the limb) was taken March 4, 1979, about 12 hours before Voyager 1's closest approach to Jupiter. This and the accompanying photo present the evidence for the first active volcanic eruption ever observed on another body in the solar system. This photo taken from a distance of 310,000 miles (499,000 kilometers), shows a plume-like structure rising more than 60 miles (100 kilometers) above the surface, a cloud of material being produced by an active eruption. At least four eruptions have been identified on Voyager 1 pictures and many more may yet be discovered on closer analysis. On a nearly airless body like Io, particulate material thrown out of a volcano follows a ballistic trajectory, accounting for the dome-like shape of the top of the cloud, formed as particles reach the top of their flight path and begin to fall back. Spherical expansion of outflowing gas forms an even larger cloud surrounding the dust. Several regions have been identified by the infrared instrument on Voyager 1 as being several hundred degrees Fahrenheit warmer than surrounding terrain, and correlated with the eruptions. The fact that several eruptions appear to be going on simultaneously makes Io the most active surface in the solar system and suggests to scientists that Io is undergoing continuous volcanism, revising downward the age of Io's surface once again. JPL manages and controls the Voyager Project for NASA's Office of Space Science.

Tuning HDF5 subfiling performance on parallel file systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byna, Suren; Chaarawi, Mohamad; Koziol, Quincey

Subfiling is a technique used on parallel file systems to reduce locking and contention issues when multiple compute nodes interact with the same storage target node. Subfiling provides a compromise between the single shared file approach that instigates the lock contention problems on parallel file systems and having one file per process, which results in generating a massive and unmanageable number of files. In this paper, we evaluate and tune the performance of recently implemented subfiling feature in HDF5. In specific, we explain the implementation strategy of subfiling feature in HDF5, provide examples of using the feature, and evaluate andmore » tune parallel I/O performance of this feature with parallel file systems of the Cray XC40 system at NERSC (Cori) that include a burst buffer storage and a Lustre disk-based storage. We also evaluate I/O performance on the Cray XC30 system, Edison, at NERSC. Our results show performance benefits of 1.2X to 6X performance advantage with subfiling compared to writing a single shared HDF5 file. We present our exploration of configurations, such as the number of subfiles and the number of Lustre storage targets to storing files, as optimization parameters to obtain superior I/O performance. Based on this exploration, we discuss recommendations for achieving good I/O performance as well as limitations with using the subfiling feature.« less

Models, figures, and gravitational moments of Jupiter's satellites Io and Europa

NASA Astrophysics Data System (ADS)

Zharkov, V. N.; Karamurzov, B. S.

2006-07-01

Two types of trial three-layer models have been constructed for the satellites Io and Europa. In the models of the first type (Io1 and E1), the cores are assumed to consist of eutectic Fe-FeS melt with the densities ρ 1 = 5.15 g cm-3 (Io1) and 5.2 g cm-3 (E1). In the models of the second type (Io3 and E3), the cores consist of FeS with an admixture of nickel and have the density ρ 1 = 4.6 g cm-3. The approach used here differs from that used previously both in chosen model chemical composition of these satellites and in boundary conditions imposed on the models. The most important question to be answered by modeling the internal structure of the Galilean satellites is that of the condensate composition at the formation epoch of Jupiter's system. Jupiter's core and the Galilean satellites were formed from the condensate. Ganymede and Callisto were formed fairly far from Jupiter in zones with temperatures below the water condensation temperature, water was entirely incorporated into their bodies, and their modeling showed the mass ratio of the icy (I) component to the rock (R) component in them to be I/R ˜ 1. The R composition must be clarified by modeling Io and Europa. The models of the second type (Io3 and E3), in which the satellite cores consist of FeS, yield 25.2 (Io3) and 22.8 (E3) for the core masses (in weight %). In discussing the R composition, we note that, theoretically, the material of which the FeS+Ni core can consist in the R accounts for ˜25.4% of the satellite mass. In this case, such an important parameter as the mantle silicate iron saturation is Fe# = 0.265. The Io3 and E3 models agree well with this theoretical prediction. The models of the first and second types differ markedly in core radius; thus, in principle, the R composition in the formation zone of Jupiter's system can be clarified by geophysical studies. Another problem studied here is that of the error made in modeling Io and Europa using the Radau-Darvin formula when passing from the Love number k 2 to the nondimensional polar moment of inertia bar C. For Io, the Radau-Darvin formula underestimates the true value of bar C by one and a half units in the third decimal digit. For Europa, this effect is approximately a factor of 3 smaller, which roughly corresponds to a ratio of the small parameters for the satellites under consideration α Io/α Europa ˜ 3.4. In modeling the internal structure of the satellites, the core radius depends strongly on both the mean moment of inertia I* and k 2. Therefore, the above discrepancy in bar C for Io is appreciable.

Tools for Large-Scale Mobile Malware Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bierma, Michael

Analyzing mobile applications for malicious behavior is an important area of re- search, and is made di cult, in part, by the increasingly large number of appli- cations available for the major operating systems. There are currently over 1.2 million apps available in both the Google Play and Apple App stores (the respec- tive o cial marketplaces for the Android and iOS operating systems)[1, 2]. Our research provides two large-scale analysis tools to aid in the detection and analysis of mobile malware. The rst tool we present, Andlantis, is a scalable dynamic analysis system capa- ble of processing over 3000more » Android applications per hour. Traditionally, Android dynamic analysis techniques have been relatively limited in scale due to the compu- tational resources required to emulate the full Android system to achieve accurate execution. Andlantis is the most scalable Android dynamic analysis framework to date, and is able to collect valuable forensic data, which helps reverse-engineers and malware researchers identify and understand anomalous application behavior. We discuss the results of running 1261 malware samples through the system, and provide examples of malware analysis performed with the resulting data. While techniques exist to perform static analysis on a large number of appli- cations, large-scale analysis of iOS applications has been relatively small scale due to the closed nature of the iOS ecosystem, and the di culty of acquiring appli- cations for analysis. The second tool we present, iClone, addresses the challenges associated with iOS research in order to detect application clones within a dataset of over 20,000 iOS applications.« less

Changes in complex spike activity during classical conditioning

PubMed Central

Rasmussen, Anders; Jirenhed, Dan-Anders; Wetmore, Daniel Z.; Hesslow, Germund

2014-01-01

The cerebellar cortex is necessary for adaptively timed conditioned responses (CRs) in eyeblink conditioning. During conditioning, Purkinje cells acquire pause responses or “Purkinje cell CRs” to the conditioned stimuli (CS), resulting in disinhibition of the cerebellar nuclei (CN), allowing them to activate motor nuclei that control eyeblinks. This disinhibition also causes inhibition of the inferior olive (IO), via the nucleo-olivary pathway (N-O). Activation of the IO, which relays the unconditional stimulus (US) to the cortex, elicits characteristic complex spikes in Purkinje cells. Although Purkinje cell activity, as well as stimulation of the CN, is known to influence IO activity, much remains to be learned about the way that learned changes in simple spike firing affects the IO. In the present study, we analyzed changes in simple and complex spike firing, in extracellular Purkinje cell records, from the C3 zone, in decerebrate ferrets undergoing training in a conditioning paradigm. In agreement with the N-O feedback hypothesis, acquisition resulted in a gradual decrease in complex spike activity during the conditioned stimulus, with a delay that is consistent with the long N-O latency. Also supporting the feedback hypothesis, training with a short interstimulus interval (ISI), which does not lead to acquisition of a Purkinje cell CR, did not cause a suppression of complex spike activity. In contrast, observations that extinction did not lead to a recovery in complex spike activity and the irregular patterns of simple and complex spike activity after the conditioned stimulus are less conclusive. PMID:25140129

An Open Source Extensible Smart Energy Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rankin, Linda

Aggregated distributed energy resources are the subject of much interest in the energy industry and are expected to play an important role in meeting our future energy needs by changing how we use, distribute and generate electricity. This energy future includes an increased amount of energy from renewable resources, load management techniques to improve resiliency and reliability, and distributed energy storage and generation capabilities that can be managed to meet the needs of the grid as well as individual customers. These energy assets are commonly referred to as Distributed Energy Resources (DER). DERs rely on a means to communicate informationmore » between an energy provider and multitudes of devices. Today DER control systems are typically vendor-specific, using custom hardware and software solutions. As a result, customers are locked into communication transport protocols, applications, tools, and data formats. Today’s systems are often difficult to extend to meet new application requirements, resulting in stranded assets when business requirements or energy management models evolve. By partnering with industry advisors and researchers, an implementation DER research platform was developed called the Smart Energy Framework (SEF). The hypothesis of this research was that an open source Internet of Things (IoT) framework could play a role in creating a commodity-based eco-system for DER assets that would reduce costs and provide interoperable products. SEF is based on the AllJoynTM IoT open source framework. The demonstration system incorporated DER assets, specifically batteries and smart water heaters. To verify the behavior of the distributed system, models of water heaters and batteries were also developed. An IoT interface for communicating between the assets and a control server was defined. This interface supports a series of “events” and telemetry reporting, similar to those defined by current smart grid communication standards. The results of this effort demonstrated the feasibility and application potential of using IoT frameworks for the creation of commodity-based DER systems. All of the identified commodity-based system requirements were met by the AllJoyn framework. By having commodity solutions, small vendors can enter the market and the cost of implementation for all parties is reduced. Utilities and aggregators can choose from multiple interoperable products reducing the risk of stranded assets. Based on this research it is recommended that interfaces based on existing smart grid communication protocol standards be created for these emerging IoT frameworks. These interfaces should be standardized as part of the IoT framework allowing for interoperability testing and certification. Similarly, IoT frameworks are introducing application level security. This type of security is needed for protecting application and platforms and will be important moving forward. Recommendations are that along with DER-based data model interfaces, platform and application security requirements also be prescribed when IoT devices support DER applications.« less

Theranostic Iron Oxide/Gold Ion Nanoprobes for MR Imaging and Noninvasive RF Hyperthermia.

PubMed

Fazal, Sajid; Paul-Prasanth, Bindhu; Nair, Shantikumar V; Menon, Deepthy

2017-08-30

This work focuses on the development of a nanoparticulate system that can be used for magnetic resonance (MR) imaging and E-field noninvasive radiofrequency (RF) hyperthermia. For this purpose, an amine-functional gold ion complex (GIC), [Au(III)(diethylenetriamine)Cl]Cl 2 , which generates heat upon RF exposure, was conjugated to carboxyl-functional poly(acrylic acid)-capped iron-oxide nanoparticles (IO-PAA NPs) to form IO-GIC NPs of size ∼100 nm. The multimodal superparamagnetic IO-GIC NPs produced T2-contrast on MR imaging and unlike IO-PAA NPs generated heat on RF exposure. The RF heating response of IO-GIC NPs was found to be dependent on the RF power, exposure period, and particle concentration. IO-GIC NPs at a concentration of 2.5 mg/mL showed a high heating response (δT) of ∼40 °C when exposed to 100 W RF power for 1 min. In vitro cytotoxicity measurements on NIH-3T3 fibroblast cells and 4T1 cancer cells showed that IO-GIC NPs are cytocompatible at high NP concentrations for up to 72 h. Upon in vitro RF exposure (100 W, 1 min), a high thermal response leads to cell death of 4T1 cancer cells incubated with IO-GIC NPs (1 mg/mL). Hematoxylin and eosin imaging of rat liver tissues injected with 100 μL of 2.5 mg/mL IO-GIC NPs and exposed to low RF power of 20 W for 10 min showed significant loss of tissue morphology at the site of injection, as against RF-exposed or nanoparticle-injected controls. In vivo MR imaging and noninvasive RF exposure of 4T1-tumor-bearing mice after IO-GIC NP administration showed T2 contrast enhancement and a localized generation of high temperatures in tumors, leading to tumor tissue damage. Furthermore, the administration of IO-GIC NPs followed by RF exposure showed no adverse acute toxicity effects in vivo. Thus, IO-GIC NPs show good promise as a theranostic agent for magnetic resonance imaging and noninvasive RF hyperthermia for cancer.

The subgenual organ complex in the cave cricket Troglophilus neglectus (Orthoptera: Rhaphidophoridae): comparative innervation and sensory evolution

PubMed Central

Strauß, Johannes; Stritih, Nataša; Lakes-Harlan, Reinhard

2014-01-01

Comparative studies of the organization of nervous systems and sensory organs can reveal their evolution and specific adaptations. In the forelegs of some Ensifera (including crickets and tettigoniids), tympanal hearing organs are located in close proximity to the mechanosensitive subgenual organ (SGO). In the present study, the SGO complex in the non-hearing cave cricket Troglophilus neglectus (Rhaphidophoridae) is investigated for the neuronal innervation pattern and for organs homologous to the hearing organs in related taxa. We analyse the innervation pattern of the sensory organs (SGO and intermediate organ (IO)) and its variability between individuals. In T. neglectus, the IO consists of two major groups of closely associated sensilla with different positions. While the distal-most sensilla superficially resemble tettigoniid auditory sensilla in location and orientation, the sensory innervation does not show these two groups to be distinct organs. Though variability in the number of sensory nerve branches occurs, usually either organ is supplied by a single nerve branch. Hence, no sensory elements clearly homologous to the auditory organ are evident. In contrast to other non-hearing Ensifera, the cave cricket sensory structures are relatively simple, consistent with a plesiomorphic organization resembling sensory innervation in grasshoppers and stick insects. PMID:26064547

A Harmonized Perspective on Transportation Management in Smart Cities: The Novel IoT-Driven Environment for Road Traffic Modeling.

PubMed

Masek, Pavel; Masek, Jan; Frantik, Petr; Fujdiak, Radek; Ometov, Aleksandr; Hosek, Jiri; Andreev, Sergey; Mlynek, Petr; Misurec, Jiri

2016-11-08

The unprecedented growth of today's cities together with increased population mobility are fueling the avalanche in the numbers of vehicles on the roads. This development led to the new challenges for the traffic management, including the mitigation of road congestion, accidents, and air pollution. Over the last decade, researchers have been focusing their efforts on leveraging the recent advances in sensing, communications, and dynamic adaptive technologies to prepare the deployed road traffic management systems (TMS) for resolving these important challenges in future smart cities. However, the existing solutions may still be insufficient to construct a reliable and secure TMS that is capable of handling the anticipated influx of the population and vehicles in urban areas. Along these lines, this work systematically outlines a perspective on a novel modular environment for traffic modeling, which allows to recreate the examined road networks in their full resemblance. Our developed solution is targeted to incorporate the progress in the Internet of Things (IoT) technologies, where low-power, embedded devices integrate as part of a next-generation TMS. To mimic the real traffic conditions, we recreated and evaluated a practical traffic scenario built after a complex road intersection within a large European city.

A Harmonized Perspective on Transportation Management in Smart Cities: The Novel IoT-Driven Environment for Road Traffic Modeling

PubMed Central

Masek, Pavel; Masek, Jan; Frantik, Petr; Fujdiak, Radek; Ometov, Aleksandr; Hosek, Jiri; Andreev, Sergey; Mlynek, Petr; Misurec, Jiri

2016-01-01

The unprecedented growth of today’s cities together with increased population mobility are fueling the avalanche in the numbers of vehicles on the roads. This development led to the new challenges for the traffic management, including the mitigation of road congestion, accidents, and air pollution. Over the last decade, researchers have been focusing their efforts on leveraging the recent advances in sensing, communications, and dynamic adaptive technologies to prepare the deployed road traffic management systems (TMS) for resolving these important challenges in future smart cities. However, the existing solutions may still be insufficient to construct a reliable and secure TMS that is capable of handling the anticipated influx of the population and vehicles in urban areas. Along these lines, this work systematically outlines a perspective on a novel modular environment for traffic modeling, which allows to recreate the examined road networks in their full resemblance. Our developed solution is targeted to incorporate the progress in the Internet of Things (IoT) technologies, where low-power, embedded devices integrate as part of a next-generation TMS. To mimic the real traffic conditions, we recreated and evaluated a practical traffic scenario built after a complex road intersection within a large European city. PMID:27834796

Predictive battlespace awareness and effects-based operations from a Homeland Security perspective: a wargaming opportunity

NASA Astrophysics Data System (ADS)

Williams, James K.; Hubbard, Zachary P.

2003-09-01

Effects Based Operations (EBO) and Predictive Battlespace Awareness (PBA) are intimately linked. Intelligence Preparation of the Battlespace (IPB), the predictive component of PBA, provides a structured analytical process for defining the battlespace environment, describing the battlespace effects that influence all sides, modeling the adversary, and determining likely enemy courses of action (COA). IPB documents some of the necessary elements of EBO, such as centers of gravity, counter-COAs, and indicators. The IPB process has been adapted to Information Operations (IO) through Intelligence Preparation of the Information Battlespace (IPIB), a prototype system for cyber-defense. IPIB ranks Enemy cyber-COAs and lists mission-critical network assets that must be defended. It is clear that IPIB can be inverted for developing COAs that implement EBO, and the prototype is being modified for offensive IO. Full-spectrum EBO would combine kinetic, cyber, and cognitive COAs to affect an adversary's behavior. This paper uses a Critical Infrastructure Protection (CIP) scenario to: 1) Provide an example of EBO-based PBA for CIP. 2) Illustrate the interaction between EBO and PBA. 3) Demonstrate the need for a national Critical Infrastructure vulnerability assessment. 4) Identify why simulation and wargaming are the most viable means of performing such an assessment.

Virtual Wireless Sensor Networks: Adaptive Brain-Inspired Configuration for Internet of Things Applications

PubMed Central

Toyonaga, Shinya; Kominami, Daichi; Murata, Masayuki

2016-01-01

Many researchers are devoting attention to the so-called “Internet of Things” (IoT), and wireless sensor networks (WSNs) are regarded as a critical technology for realizing the communication infrastructure of the future, including the IoT. Against this background, virtualization is a crucial technique for the integration of multiple WSNs. Designing virtualized WSNs for actual environments will require further detailed studies. Within the IoT environment, physical networks can undergo dynamic change, and so, many problems exist that could prevent applications from running without interruption when using the existing approaches. In this paper, we show an overall architecture that is suitable for constructing and running virtual wireless sensor network (VWSN) services within a VWSN topology. Our approach provides users with a reliable VWSN network by assigning redundant resources according to each user’s demand and providing a recovery method to incorporate environmental changes. We tested this approach by simulation experiment, with the results showing that the VWSN network is reliable in many cases, although physical deployment of sensor nodes and the modular structure of the VWSN will be quite important to the stability of services within the VWSN topology. PMID:27548177

Virtual Wireless Sensor Networks: Adaptive Brain-Inspired Configuration for Internet of Things Applications.

PubMed

Toyonaga, Shinya; Kominami, Daichi; Murata, Masayuki

2016-08-19

Many researchers are devoting attention to the so-called "Internet of Things" (IoT), and wireless sensor networks (WSNs) are regarded as a critical technology for realizing the communication infrastructure of the future, including the IoT. Against this background, virtualization is a crucial technique for the integration of multiple WSNs. Designing virtualized WSNs for actual environments will require further detailed studies. Within the IoT environment, physical networks can undergo dynamic change, and so, many problems exist that could prevent applications from running without interruption when using the existing approaches. In this paper, we show an overall architecture that is suitable for constructing and running virtual wireless sensor network (VWSN) services within a VWSN topology. Our approach provides users with a reliable VWSN network by assigning redundant resources according to each user's demand and providing a recovery method to incorporate environmental changes. We tested this approach by simulation experiment, with the results showing that the VWSN network is reliable in many cases, although physical deployment of sensor nodes and the modular structure of the VWSN will be quite important to the stability of services within the VWSN topology.

The role of Fizeau interferometry in planetary science

NASA Astrophysics Data System (ADS)

Conrad, Albert R.

2016-08-01

Historically, two types of interferometer have been used to the study of solar system objects: coaxial and Fizeau. While coaxial interferometers are well-suited to a wide range of galactic and extra-galactic science cases, solar system science cases are, in most cases, better carried out with Fizeau imagers. Targets of interest in our solar system are often bright and compact, and the science cases for these objects often call for a complete, or nearly complete, image at high angular resolution. For both methods, multiple images must be taken at varying baselines to reconstruct an image. However, with the Fizeau technique that number is far fewer than it is for the aperture synthesis method employed by co-axial interferometers. In our solar system, bodies rotate and their surfaces are sometimes changing over yearly, or even weekly, time scales. Thus, the need to be able to exploit the high angular resolution of an interferometer with only a handful of observations taken on a single night, as is the case for Fizeau interferometers, gives a key advantage to this technique. The aperture of the Large Binocular Telescope (LBT), two 8.4 circular mirrors separated center-to-center by 14.4 meters, is optimal for supporting Fizeau interferometry. The first of two Fizeau imagers planned for LBT, the LBT Interferometer (LBTI),1 saw first fringes in 2010 and has proven to be a valuable tool for solar system studies. Recent studies of Jupiters volcanic moon Io have yielded results that rely on the angular resolution provided by the full 23-meter baseline of LBT Future studies of the aurora at Jupiters poles and the shape and binarity of asteroids are planned. While many solar system studies can be carried out on-axis (i.e., using the target of interest as the beacon for both adaptive optics correction and fringe tracking), studies such as Io-in-eclipse, full disk of Jupiter and Mars, and binarity of Kuiper belt objects, require off-axis observations (i.e., using one or more nearby guide-moons or stars for adaptive optics correction and fringe tracking). These studies can be plagued by anisoplanatism, or cone effect. LINC-NIRVANA (LN),2 the first multi-conjugate adaptive optics system (MCAO) on an 8-meter class telescope in the northern hemisphere, provides a solution to the ill-effects of anisoplanatism. One of the LN ground layer wave front sensors was tested on LBT during 2014.3-5 Longer term, an upgrade planned for LN will establish its original role as the second LBT Fizeau imager. The full-disk study of several solar system bodies, most notably large and/or nearby bodies such as Jupiter and Mars which span tens of arcseconds, would be best studied with LN. We will review the past accomplishments of Fizeau interferometry with LBTI, present plans for using that instrument for future solar system studies, and, lastly, explore the unique solar system studies that require the LN MCAO system combined with Fizeau interferometry.

Time-Aware Service Ranking Prediction in the Internet of Things Environment

PubMed Central

Huang, Yuze; Huang, Jiwei; Cheng, Bo; He, Shuqing; Chen, Junliang

2017-01-01

With the rapid development of the Internet of things (IoT), building IoT systems with high quality of service (QoS) has become an urgent requirement in both academia and industry. During the procedures of building IoT systems, QoS-aware service selection is an important concern, which requires the ranking of a set of functionally similar services according to their QoS values. In reality, however, it is quite expensive and even impractical to evaluate all geographically-dispersed IoT services at a single client to obtain such a ranking. Nevertheless, distributed measurement and ranking aggregation have to deal with the high dynamics of QoS values and the inconsistency of partial rankings. To address these challenges, we propose a time-aware service ranking prediction approach named TSRPred for obtaining the global ranking from the collection of partial rankings. Specifically, a pairwise comparison model is constructed to describe the relationships between different services, where the partial rankings are obtained by time series forecasting on QoS values. The comparisons of IoT services are formulated by random walks, and thus, the global ranking can be obtained by sorting the steady-state probabilities of the underlying Markov chain. Finally, the efficacy of TSRPred is validated by simulation experiments based on large-scale real-world datasets. PMID:28448451

Time-Aware Service Ranking Prediction in the Internet of Things Environment.

PubMed

Huang, Yuze; Huang, Jiwei; Cheng, Bo; He, Shuqing; Chen, Junliang

2017-04-27

With the rapid development of the Internet of things (IoT), building IoT systems with high quality of service (QoS) has become an urgent requirement in both academia and industry. During the procedures of building IoT systems, QoS-aware service selection is an important concern, which requires the ranking of a set of functionally similar services according to their QoS values. In reality, however, it is quite expensive and even impractical to evaluate all geographically-dispersed IoT services at a single client to obtain such a ranking. Nevertheless, distributed measurement and ranking aggregation have to deal with the high dynamics of QoS values and the inconsistency of partial rankings. To address these challenges, we propose a time-aware service ranking prediction approach named TSRPred for obtaining the global ranking from the collection of partial rankings. Specifically, a pairwise comparison model is constructed to describe the relationships between different services, where the partial rankings are obtained by time series forecasting on QoS values. The comparisons of IoT services are formulated by random walks, and thus, the global ranking can be obtained by sorting the steady-state probabilities of the underlying Markov chain. Finally, the efficacy of TSRPred is validated by simulation experiments based on large-scale real-world datasets.

Real-Time Adaptive Control of Mixing in a Plane Shear Layer

DTIC Science & Technology

1992-01-01

ODAT1 3*as ypt AND OAIU COVusa3 Ja 192A6ua Technical 15 Jan 91 - 14 Jan 𔃼 rrlTLAND SUR0(U) T a 192= Pij. m F N IEu M Real-Time Adaptive Control of...0465 Submitted to Air Force Office of Scientific Research Boiling Air Force Base, Building 410 Washington, D.C. 20332 Submitted by A. Glezer Acc&:io n F1...t ibu_:ion i ... ..... ... . Aw ilfbility Cc.C’ Dist Spec I A-1 92-05643 92 1 3a 12 TABLE OF CONTENTS IN TRO D U CTIO N

Infrared speckle interferometry and spectroscopy of Io

NASA Technical Reports Server (NTRS)

Howell, Robert R.

1991-01-01

The goal during the last year was to continue the speckle monitoring of volcanic hot spots on Io, and to begin observations of the 1991 series of mutual events between Io and Europa. The former provide a time history of the volcanic activity, while the latter give the highest spatial resolution and the best sensitivity to faint spots. A minor component of the program is lunar occultation observations of young T Tauri stars. The occultations provide milliarcsecond resolution which let us search for circumstellar material and determine which systems are multiple.

The condensation and vaporization behavior of ices containing SO2, H2S, and CO2 - Implications for Io

NASA Astrophysics Data System (ADS)

Sandford, Scott A.; Allamandola, Louis J.

1993-12-01

The present compilation of measurements of the physical and IR spectral properties of ices whose molecular compositions are relevant to the case of Io encompasses ice systems containing SO2, H2S, and CO2. Surface-binding energies used to calculate the residence times of molecules on a surface as a function of temperature furnish crucially important parameters for models attending to the transport of such molecules to the surface of Io. The values thus derived show that SO2 frosts anneal rapidly.

Gene distribution of ABO blood type system on the Dengue Hemorrhagic Fever (DHF) patients in the working area of Puskesmas Bonto Bangun, District of Rilau Ale, Bulukumba

NASA Astrophysics Data System (ADS)

Sjafaraenan; Alvionita, D. N.; Agus, R.; Sabran, A.

2018-03-01

This research is about gene distribution of ABO blood type system on the Dengue Hemorrhagic Fever (DHF) patients in the working area of Puskesmas Bonto Bangun, District of Rilau Ale, Bulukumba. This research aimed to determine the blood type which is most affected by DHF using ABO blood type system. In this research, there are 104 samples, 8 of them were attacked by DF and 96 were attacked by DHF. From the 96 patients of DHF, there were 38 patients with A-blood type, 17 patients with B-blood type, 36 patients with O-blood type and 5 patients of AB-blood type. The data were tested using genotype frequency test and the results showed that the percentage of A-homozygous blood type (IAIA) is 0:09%; A heterozygous blood type (IAIo) is 0:36%; B-homozygous blood type (IBIB) is 0.01%; B heterozygous blood type (IB Io) is 0.12%; AB blood type (IAIB) is 0.06% and O blood type (IoIo) is 12:36%. So the biggest frequency of genotype are IAIo (0.36%) and IoIo (0.36%). The results showed that O blood type gene is the most affected by DHF. Then continued by the regression test between blood type and DHF, it is obtained that the correlation value is 1 which indicated that there is a strong relationship.

Io Plume Monitoring (frames 1-36)

NASA Image and Video Library

1997-11-04

A sequence of full disk Io images was taken prior to Galileo's second encounter with Ganymede. The purpose of these observations was to view all longitudes of Io and search for active volcanic plumes. The images were taken at intervals of approximately one hour corresponding to Io longitude increments of about ten degrees. Because both the spacecraft and Io were traveling around Jupiter the lighting conditions on Io (e.g. the phase of Io) changed dramatically during the sequence. These images were registered at a common scale and processed to produce a time-lapse "movie" of Io. This movie combines all of the plume monitoring frames obtained by the Solid State Imaging system aboard NASA's Galileo spacecraft. The most prominent volcanic plume seen in this movie is Prometheus (latitude 1.6 south, longitude 153 west). The plume becomes visible as it moves into daylight, crosses the center of the disk, and is seen in profile against the dark of space at the edge of Io. This plume was first seen by the Voyager 1 spacecraft in 1979 and is believed to be a geyser-like eruption of sulfur dioxide snow and gas. Although details of the region around Prometheus have changed in the seventeen years since Voyager's visit, the shape and height of the plume have not changed significantly. It is possible that this geyser has been erupting nearly continuously over this time. Galileo's primary 24 month mission includes eleven orbits around Jupiter and will provide observations of Jupiter, its moons and its magnetosphere. North is to the top of all frames. The smallest features which can be discerned range from 13 to 31 kilometers across. The images were obtained between the 2nd and the 6th of September, 1996. The animation can be viewed at http://photojournal.jpl.nasa.gov/catalog/PIA01073

System III variations in apparent distance of Io plasma torus from Jupiter

NASA Technical Reports Server (NTRS)

Dessler, A. J.; Sandel, B. R.

1992-01-01

System III variations in apparent distance of the Io plasma torus from Jupiter are examined on the basis of data obtained from UVS scans across Jupiter's satellite system. The displacement of the dawn and dusk ansae are found to be unexpectedly complex. The displacements are unequal and both ansae are in motion with the motion of the approaching ansa being the lesser of the two. The radial motions, as measured from either the center of Jupiter or the offset-tilted dipole, are of unequal magnitude and have the System III periodicity. It is concluded that the cross-tail electric field that causes these torus motions is concentrated on the dusk ansa, varied with the System III period, and shows magnetic-anomaly phase control. It is found that the dawn-dust asymmetry in brightness is not explained simply by the cross-tail electric field. It is concluded that there is a heating mechanism that causes the dusk side of the Io plasma torus to be brighter than the dawn side.

Differential barometric-based positioning technique for indoor elevation measurement in IoT medical applications.

PubMed

Wang, Hua; Wen, Yingyou; Zhao, Dazhe

2017-07-20

Medical applications have begun to benefit from Internet of Things (IoT) technology through the introduction of wearable devices. Several medical applications require accurate patient location as various changes affect pressure parameters inside the body. This study aims to develop a system to measure indoor altitude for IoT medical applications. We propose a differential barometric-based positioning system to estimate the altitude between a reference sensor and a localizing sensor connected to the human body. The differential barometric altimetry model is introduced to estimate indoor elevations and eliminate environmental artifacts. In addition, a Gaussian filter processing is adopted to remove noise from the elevation measurements. The proposed system is then investigated through extensive experiments, using various evaluation criteria. The results indicate that the proposed system yielded good accuracy with reduced implementation complexity and fewer costs. The proposed system is resilient compared to other indoor localization approaches, even when numerous environmental artifacts in indoor environments are present.

Generic FPGA-Based Platform for Distributed IO in Proton Therapy Patient Safety Interlock System

NASA Astrophysics Data System (ADS)

Eichin, Michael; Carmona, Pablo Fernandez; Johansen, Ernst; Grossmann, Martin; Mayor, Alexandre; Erhardt, Daniel; Gomperts, Alexander; Regele, Harald; Bula, Christian; Sidler, Christof

2017-06-01

At the Paul Scherrer Institute (PSI) in Switzerland, cancer patients are treated with protons. Proton therapy at PSI has a long history and started in the 1980s. More than 30 years later, a new gantry has recently been installed in the existing facility. This new machine has been delivered by an industry partner. A big challenge is the integration of the vendor's safety system into the existing PSI environment. Different interface standards and the complexity of the system made it necessary to find a technical solution connecting an industry system to the existing PSI infrastructure. A novel very flexible distributed IO system based on field-programmable gate array (FPGA) technology was developed, supporting many different IO interface standards and high-speed communication links connecting the device to a PSI standard versa module eurocard-bus input output controller. This paper summarizes the features of the hardware technology, the FPGA framework with its high-speed communication link protocol, and presents our first measurement results.

Cassini-VIMS at Jupiter: Solar occultation measurements using Io

USGS Publications Warehouse

Formisano, V.; D'Aversa, E.; Bellucci, G.; Baines, K.H.; Bibring, J.-P.; Brown, R.H.; Buratti, B.J.; Capaccioni, F.; Cerroni, P.; Clark, R.N.; Coradini, A.; Cruikshank, D.P.; Drossart, P.; Jaumann, R.; Langevin, Y.; Matson, D.L.; McCord, T.B.; Mennella, V.; Nelson, R.M.; Nicholson, P.D.; Sicardy, B.; Sotin, Christophe; Chamberlain, M.C.; Hansen, G.; Hibbits, K.; Showalter, M.; Filacchione, G.

2003-01-01

We report unusual and somewhat unexpected observations of the jovian satellite Io, showing strong methane absorption bands. These observations were made by the Cassini VIMS experiment during the Jupiter flyby of December/January 2000/2001. The explanation is straightforward: Entering or exiting from Jupiter's shadow during an eclipse, Io is illuminated by solar light which has transited the atmosphere of Jupiter. This light, therefore becomes imprinted with the spectral signature of Jupiter's upper atmosphere, which includes strong atmospheric methane absorption bands. Intercepting solar light refracted by the jovian atmosphere, Io essentially becomes a "miffor" for solar occultation events of Jupiter. The thickness of the layer where refracted solar light is observed is so large (more than 3000 km at Io's orbit), that we can foresee a nearly continuous multi-year period of similar events at Saturn, utilizing the large and bright ring system. During Cassini's 4-year nominal mission, this probing tecnique should reveal information of Saturn's atmosphere over a large range of southern latitudes and times. ?? 2003 Elsevier Inc. All rights reserved.

A Survey on Energy Conserving Mechanisms for the Internet of Things: Wireless Networking Aspects.

PubMed

Abbas, Zeeshan; Yoon, Wonyong

2015-09-25

The Internet of Things (IoT) is an emerging key technology for future industries and everyday lives of people, where a myriad of battery operated sensors, actuators, and smart objects are connected to the Internet to provide services such as mobile healthcare, intelligent transport system, environmental monitoring, etc. Since energy efficiency is of utmost importance to these battery constrained IoT devices, IoT-related standards and research works have focused on the device energy conserving issues. This paper presents a comprehensive survey on energy conserving issues and solutions in using diverse wireless radio access technologies for IoT connectivity, e.g., the 3rd Generation Partnership Project (3GPP) machine type communications, IEEE 802.11ah, Bluetooth Low Energy (BLE), and Z-Wave. We look into the literature in broad areas of standardization, academic research, and industry development, and structurally summarize the energy conserving solutions based on several technical criteria. We also propose future research directions regarding energy conserving issues in wireless networking-based IoT.

Learning the ideal observer for SKE detection tasks by use of convolutional neural networks (Cum Laude Poster Award)

NASA Astrophysics Data System (ADS)

Zhou, Weimin; Anastasio, Mark A.

2018-03-01

It has been advocated that task-based measures of image quality (IQ) should be employed to evaluate and optimize imaging systems. Task-based measures of IQ quantify the performance of an observer on a medically relevant task. The Bayesian Ideal Observer (IO), which employs complete statistical information of the object and noise, achieves the upper limit of the performance for a binary signal classification task. However, computing the IO performance is generally analytically intractable and can be computationally burdensome when Markov-chain Monte Carlo (MCMC) techniques are employed. In this paper, supervised learning with convolutional neural networks (CNNs) is employed to approximate the IO test statistics for a signal-known-exactly and background-known-exactly (SKE/BKE) binary detection task. The receiver operating characteristic (ROC) curve and the area under the ROC curve (AUC) are compared to those produced by the analytically computed IO. The advantages of the proposed supervised learning approach for approximating the IO are demonstrated.

A Survey on Energy Conserving Mechanisms for the Internet of Things: Wireless Networking Aspects

PubMed Central

Abbas, Zeeshan; Yoon, Wonyong

2015-01-01

The Internet of Things (IoT) is an emerging key technology for future industries and everyday lives of people, where a myriad of battery operated sensors, actuators, and smart objects are connected to the Internet to provide services such as mobile healthcare, intelligent transport system, environmental monitoring, etc. Since energy efficiency is of utmost importance to these battery constrained IoT devices, IoT-related standards and research works have focused on the device energy conserving issues. This paper presents a comprehensive survey on energy conserving issues and solutions in using diverse wireless radio access technologies for IoT connectivity, e.g., the 3rd Generation Partnership Project (3GPP) machine type communications, IEEE 802.11ah, Bluetooth Low Energy (BLE), and Z-Wave. We look into the literature in broad areas of standardization, academic research, and industry development, and structurally summarize the energy conserving solutions based on several technical criteria. We also propose future research directions regarding energy conserving issues in wireless networking-based IoT. PMID:26404275

Power Consumption and Calculation Requirement Analysis of AES for WSN IoT.

PubMed

Hung, Chung-Wen; Hsu, Wen-Ting

2018-05-23

Because of the ubiquity of Internet of Things (IoT) devices, the power consumption and security of IoT systems have become very important issues. Advanced Encryption Standard (AES) is a block cipher algorithm is commonly used in IoT devices. In this paper, the power consumption and cryptographic calculation requirement for different payload lengths and AES encryption types are analyzed. These types include software-based AES-CB, hardware-based AES-ECB (Electronic Codebook Mode), and hardware-based AES-CCM (Counter with CBC-MAC Mode). The calculation requirement and power consumption for these AES encryption types are measured on the Texas Instruments LAUNCHXL-CC1310 platform. The experimental results show that the hardware-based AES performs better than the software-based AES in terms of power consumption and calculation cycle requirements. In addition, in terms of AES mode selection, the AES-CCM-MIC64 mode may be a better choice if the IoT device is considering security, encryption calculation requirement, and low power consumption at the same time. However, if the IoT device is pursuing lower power and the payload length is generally less than 16 bytes, then AES-ECB could be considered.

Study of the NASTRAN input/output systems

NASA Technical Reports Server (NTRS)

Brown, W. K.; Schoellmann, W. F.

1977-01-01

The basic characteristics of the NASTRAN level 16 I/O subsystem are presented with particular reference to blocking/deblocking aspects, I/O methods used on the IBM, CDC, and UNIVAC machines, definition of basic NASTRAN I/O control tables, and portability of parts of the I/O subsystem to other programs outside the NASTRAN environment are included. An explanation of the IBM primary, secondary, and tertiary files defined by the data definition (DD) cards in the NASTRAN JCL procedure. The explanation is intended to enlighten users as to the purpose of these DD cards, how they relate to one another, and why there are no similar type definition cards required on the CDC and UNIVAC versions. Enhancements designed to increase overall efficiency and decrease core requirements are also recommended.

Monitoring Io volcanism with AO telescopes during and after the NH flyby

NASA Astrophysics Data System (ADS)

Marchis, F.; Spencer, J. R.; Lopes, R. M.; Davies, A. G.; Dumas, C.

2007-12-01

To support the New Horizons (NH) Jupiter encounter we monitored Io's volcanic activity using high angular resolution images in the near infrared (1-5 microns) provided by adaptive optics (AO) systems available on 8-10m class telescopes. We initiated the campaign on Feb. 25 2007 with data obtained with the VLT-Yepun telescope (ESO, Paranal, Chile), just before NH closest approach. We continued monitoring with the Gemini North telescope (Hawaii, USA). The last observation was taken on May 28 2007. Numerous active volcanoes are visible in the data but the Tvashtar eruption is by far the most energetic. Extremely high angular resolution data from NH revealed fine detail of the eruption, such as the presence of an active plume [1]. This volcano has an interesting past history. It was seen as a powerful eruption from Nov. 26 1999 during the Galileo I25 [2] flyby to Feb. 19 2001 from the ground [3]. It was dormant or below our ground-based limit of detection (T<330 K assuming an area of 460 km2) between Dec 2001 and May 2004 [4,5]. The re-awakening of the volcano was reported by Laver et al. [6] in April 2006 based on Keck Adaptive Optics (AO) observations. Our last Gemini AO observation taken on May 26 shows that Tvashtar was still very active. Based on the previous behavior of this volcano [7] it is very likely that the activity reported in 2007 is a continuation of the Tvashtar-2006 eruption. Other hot spots, such as Loki Patera, Pele, and a new hot spot located north of Loki Patera, were seen in our data. We will describe the global picture of Io's volcanic activity derived from our observations, comparing it with previous observations from the Galileo spacecraft and using ground-based AO. 1. Spencer et al., AGU, this session, 2007 2. McEwen et al., Science, 288, 1193-1198, 2000 3. Marchis et al. Icarus, 160, 124-131, 2002 4. Marchis et al., Icarus, 176, 1, 2005 5. Marchis et al., AGU Fall meeting, V33C-1483, 2004 6. Laver et al., Icarus, in press, 2006 7. Milazzo et al., 2005, Icarus, 179, 235-51

Current-mode subthreshold MOS implementation of the Herault-Jutten autoadaptive network

NASA Astrophysics Data System (ADS)

Cohen, Marc H.; Andreou, Andreas G.

1992-05-01

The translinear circuits in subthreshold MOS technology and current-mode design techniques for the implementation of neuromorphic analog network processing are investigated. The architecture, also known as the Herault-Jutten network, performs an independent component analysis and is essentially a continuous-time recursive linear adaptive filter. Analog I/O interface, weight coefficients, and adaptation blocks are all integrated on the chip. A small network with six neurons and 30 synapses was fabricated in a 2-microns n-well double-polysilicon, double-metal CMOS process. Circuit designs at the transistor level yield area-efficient implementations for neurons, synapses, and the adaptation blocks. The design methodology and constraints as well as test results from the fabricated chips are discussed.

Enabling Large-Scale IoT-Based Services through Elastic Publish/Subscribe.

PubMed

Vavassori, Sergio; Soriano, Javier; Fernández, Rafael

2017-09-19

In this paper, we report an algorithm that is designed to leverage the cloud as infrastructure to support Internet of Things (IoT) by elastically scaling in/out so that IoT-based service users never stop receiving sensors' data. This algorithm is able to provide an uninterrupted service to end users even during the scaling operation since its internal state repartitioning is transparent for publishers or subscribers; its scaling operation is time-bounded and depends only on the dimension of the state partitions to be transmitted to the different nodes. We describe its implementation in E-SilboPS, an elastic content-based publish/subscribe (CBPS) system specifically designed to support context-aware sensing and communication in IoT-based services. E-SilboPS is a key internal asset of the FIWARE IoT services enablement platform, which offers an architecture of components specifically designed to capture data from, or act upon, IoT devices as easily as reading/changing the value of attributes linked to context entities. In addition, we discuss the quantitative measurements used to evaluate the scale-out process, as well as the results of this evaluation. This new feature rounds out the context-aware content-based features of E-SilboPS by providing, for example, the necessary middleware for constructing dashboards and monitoring panels that are capable of dynamically changing queries and continuously handling data in IoT-based services.

Enabling Large-Scale IoT-Based Services through Elastic Publish/Subscribe

PubMed Central

2017-01-01

In this paper, we report an algorithm that is designed to leverage the cloud as infrastructure to support Internet of Things (IoT) by elastically scaling in/out so that IoT-based service users never stop receiving sensors’ data. This algorithm is able to provide an uninterrupted service to end users even during the scaling operation since its internal state repartitioning is transparent for publishers or subscribers; its scaling operation is time-bounded and depends only on the dimension of the state partitions to be transmitted to the different nodes. We describe its implementation in E-SilboPS, an elastic content-based publish/subscribe (CBPS) system specifically designed to support context-aware sensing and communication in IoT-based services. E-SilboPS is a key internal asset of the FIWARE IoT services enablement platform, which offers an architecture of components specifically designed to capture data from, or act upon, IoT devices as easily as reading/changing the value of attributes linked to context entities. In addition, we discuss the quantitative measurements used to evaluate the scale-out process, as well as the results of this evaluation. This new feature rounds out the context-aware content-based features of E-SilboPS by providing, for example, the necessary middleware for constructing dashboards and monitoring panels that are capable of dynamically changing queries and continuously handling data in IoT-based services. PMID:28925967

Evaluation of impulse oscillometry during bronchial challenge testing in children.

PubMed

Bailly, Carole; Crenesse, Dominique; Albertini, Marc

2011-12-01

The impulse oscillation system (IOS) allows easy measurement of respiratory system impedance (Zrs). The aim of this retrospective study was to evaluate the accuracy of IOS parameters obtained during methacholine challenge by comparison with "the gold standard" forced expiratory volume in the first second (FEV1). Measurements of FEV1 and resistances at 5 and 20 Hz, reactance at 5 Hz, impedance at 5 Hz and resonant frequency were performed in 227 children with suspected asthma, before and during methacholine challenge. Data were analyzed in the overall population and in three subgroups according to the final diagnosis: asthma (n = 72), chronic cough and nonspecific respiratory symptoms (n = 122), allergic rhinitis (n = 33). All IOS parameters changed significantly during the tests but only changes in X5 were significantly different between responders and nonresponders. Moreover, changes in IOS parameters were not correlated with changes in FEV1 apart from a weak correlation for X5. The receiver operating characteristic (ROC) curve for changes in X5 (to predict a 20% decrease in FEV1 showed a best decision level for a 50% decrease in X5 with a sensitivity of 36% and a specificity of 85%. Results were not different in the asthma group. The accuracy of measurements by IOS during methacholine bronchial challenge in children was not suitable when compared with FEV1 . It could be assumed that spirometry and IOS, while both providing indirect indices of airway patency, are exploring different mechanisms, each with its own methodological potentials and limitations. Copyright © 2011 Wiley Periodicals, Inc.

An Architecture Framework for Orchestrating Context-Aware IT Ecosystems: A Case Study for Quantitative Evaluation †.

PubMed

Park, Soojin; Park, Sungyong; Park, Young B

2018-02-12

With the emergence of various forms of smart devices and new paradigms such as the Internet of Things (IoT) concept, the IT (Information Technology) service areas are expanding explosively compared to the provision of services by single systems. A new system operation concept that has emerged in accordance with such technical trends is the IT ecosystem. The IT ecosystem can be considered a special type of system of systems in which multiple systems with various degrees of autonomy achieve common goals while adapting to the given environment. The single systems that participate in the IT ecosystem adapt autonomously to the current situation based on collected data from sensors. Furthermore, to maintain the services supported by the whole IT ecosystem sustainably, the configuration of single systems that participate in the IT ecosystem also changes appropriately in accordance with the changed situation. In order to support the IT ecosystem, this paper proposes an architecture framework that supports dynamic configuration changes to achieve the goal of the whole IT ecosystem, while ensuring the autonomy of single systems through the collection of data from sensors so as to recognize the situational context of individual participating systems. For the feasibility evaluation of the proposed framework, a simulated example of an IT ecosystem for unmanned forest management was constructed, and the quantitative evaluation results are discussed in terms of the extent to which the proposed architecture framework can continuously provide sustainable services in response to diverse environmental context changes.

An Architecture Framework for Orchestrating Context-Aware IT Ecosystems: A Case Study for Quantitative Evaluation †

PubMed Central

Park, Young B.

2018-01-01

With the emergence of various forms of smart devices and new paradigms such as the Internet of Things (IoT) concept, the IT (Information Technology) service areas are expanding explosively compared to the provision of services by single systems. A new system operation concept that has emerged in accordance with such technical trends is the IT ecosystem. The IT ecosystem can be considered a special type of system of systems in which multiple systems with various degrees of autonomy achieve common goals while adapting to the given environment. The single systems that participate in the IT ecosystem adapt autonomously to the current situation based on collected data from sensors. Furthermore, to maintain the services supported by the whole IT ecosystem sustainably, the configuration of single systems that participate in the IT ecosystem also changes appropriately in accordance with the changed situation. In order to support the IT ecosystem, this paper proposes an architecture framework that supports dynamic configuration changes to achieve the goal of the whole IT ecosystem, while ensuring the autonomy of single systems through the collection of data from sensors so as to recognize the situational context of individual participating systems. For the feasibility evaluation of the proposed framework, a simulated example of an IT ecosystem for unmanned forest management was constructed, and the quantitative evaluation results are discussed in terms of the extent to which the proposed architecture framework can continuously provide sustainable services in response to diverse environmental context changes. PMID:29439540

Electrical Design and Evaluation of Asynchronous Serial Bus Communication Network of 48 Sensor Platform LSIs with Single-Ended I/O for Integrated MEMS-LSI Sensors

PubMed Central

Shao, Chenzhong; Tanaka, Shuji; Nakayama, Takahiro; Hata, Yoshiyuki

2018-01-01

For installing many sensors in a limited space with a limited computing resource, the digitization of the sensor output at the site of sensation has advantages such as a small amount of wiring, low signal interference and high scalability. For this purpose, we have developed a dedicated Complementary Metal-Oxide-Semiconductor (CMOS) Large-Scale Integration (LSI) (referred to as “sensor platform LSI”) for bus-networked Micro-Electro-Mechanical-Systems (MEMS)-LSI integrated sensors. In this LSI, collision avoidance, adaptation and event-driven functions are simply implemented to relieve data collision and congestion in asynchronous serial bus communication. In this study, we developed a network system with 48 sensor platform LSIs based on Printed Circuit Board (PCB) in a backbone bus topology with the bus length being 2.4 m. We evaluated the serial communication performance when 48 LSIs operated simultaneously with the adaptation function. The number of data packets received from each LSI was almost identical, and the average sampling frequency of 384 capacitance channels (eight for each LSI) was 73.66 Hz. PMID:29342923

JTF CapMed Initial Outfitting and Transition (IO&T) - History, Process, Benefits

DTIC Science & Technology

2011-01-26

Sharing Knowledge: Achieving Breakthrough Performance 2010 Military Health System Conference JTF CapMed 26 January, 2011 CAPT Russell Pendergrass...The Quadruple Aim: Working Together, Achieving Success 2011 Military Health System Confer nce JTF CapMed Initial Outfitting and Transition (IO&T...number. 1. REPORT DATE 26 JAN 2011 2. REPORT TYPE 3. DATES COVERED 00-00-2011 to 00-00-2011 4. TITLE AND SUBTITLE JTF CapMed Initial Outfitting

VPI - VIBRATION PATTERN IMAGER: A CONTROL AND DATA ACQUISITION SYSTEM FOR SCANNING LASER VIBROMETERS

NASA Technical Reports Server (NTRS)

Rizzi, S. A.

1994-01-01

The Vibration Pattern Imager (VPI) system was designed to control and acquire data from laser vibrometer sensors. The PC computer based system uses a digital signal processing (DSP) board and an analog I/O board to control the sensor and to process the data. The VPI system was originally developed for use with the Ometron VPI Sensor (Ometron Limited, Kelvin House, Worsley Bridge Road, London, SE26 5BX, England), but can be readily adapted to any commercially available sensor which provides an analog output signal and requires analog inputs for control of mirror positioning. VPI's graphical user interface allows the operation of the program to be controlled interactively through keyboard and mouse-selected menu options. The main menu controls all functions for setup, data acquisition, display, file operations, and exiting the program. Two types of data may be acquired with the VPI system: single point or "full field". In the single point mode, time series data is sampled by the A/D converter on the I/O board at a user-defined rate for the selected number of samples. The position of the measuring point, adjusted by mirrors in the sensor, is controlled via a mouse input. In the "full field" mode, the measurement point is moved over a user-selected rectangular area with up to 256 positions in both x and y directions. The time series data is sampled by the A/D converter on the I/O board and converted to a root-mean-square (rms) value by the DSP board. The rms "full field" velocity distribution is then uploaded for display and storage. VPI is written in C language and Texas Instruments' TMS320C30 assembly language for IBM PC series and compatible computers running MS-DOS. The program requires 640K of RAM for execution, and a hard disk with 10Mb or more of disk space is recommended. The program also requires a mouse, a VGA graphics display, a Four Channel analog I/O board (Spectrum Signal Processing, Inc.; Westborough, MA), a break-out box and a Spirit-30 board (Sonitech International, Inc.; Wellesley, MA) which includes a TMS320C30 DSP processor, 256Kb zero wait state SRAM, and a daughter board with 8Mb one wait state DRAM. Please contact COSMIC for additional information on required hardware and software. In order to compile the provided VPI source code, a Microsoft C version 6.0 compiler, a Texas Instruments' TMS320C30 assembly language compiler, and the Spirit 30 run time libraries are required. A math co-processor is highly recommended. A sample MS-DOS executable is provided on the distribution medium. The standard distribution medium for this program is one 5.25 inch 360K MS-DOS format diskette. The contents of the diskettes are compressed using the PKWARE archiving tools. The utility to unarchive the files, PKUNZIP.EXE, is included. VPI was developed in 1991-1992.

Realizing IoT service's policy privacy over publish/subscribe-based middleware.

PubMed

Duan, Li; Zhang, Yang; Chen, Shiping; Wang, Shiyao; Cheng, Bo; Chen, Junliang

2016-01-01

The publish/subscribe paradigm makes IoT service collaborations more scalable and flexible, due to the space, time and control decoupling of event producers and consumers. Thus, the paradigm can be used to establish large-scale IoT service communication infrastructures such as Supervisory Control and Data Acquisition systems. However, preserving IoT service's policy privacy is difficult in this paradigm, because a classical publisher has little control of its own event after being published; and a subscriber has to accept all the events from the subscribed event type with no choice. Few existing publish/subscribe middleware have built-in mechanisms to address the above issues. In this paper, we present a novel access control framework, which is capable of preserving IoT service's policy privacy. In particular, we adopt the publish/subscribe paradigm as the IoT service communication infrastructure to facilitate the protection of IoT services policy privacy. The key idea in our policy-privacy solution is using a two-layer cooperating method to match bi-directional privacy control requirements: (a) data layer for protecting IoT events; and (b) application layer for preserving the privacy of service policy. Furthermore, the anonymous-set-based principle is adopted to realize the functionalities of the framework, including policy embedding and policy encoding as well as policy matching. Our security analysis shows that the policy privacy framework is Chosen-Plaintext Attack secure. We extend the open source Apache ActiveMQ broker by building into a policy-based authorization mechanism to enforce the privacy policy. The performance evaluation results indicate that our approach is scalable with reasonable overheads.

High-performance mass storage system for workstations

NASA Technical Reports Server (NTRS)

Chiang, T.; Tang, Y.; Gupta, L.; Cooperman, S.

1993-01-01

Reduced Instruction Set Computer (RISC) workstations and Personnel Computers (PC) are very popular tools for office automation, command and control, scientific analysis, database management, and many other applications. However, when using Input/Output (I/O) intensive applications, the RISC workstations and PC's are often overburdened with the tasks of collecting, staging, storing, and distributing data. Also, by using standard high-performance peripherals and storage devices, the I/O function can still be a common bottleneck process. Therefore, the high-performance mass storage system, developed by Loral AeroSys' Independent Research and Development (IR&D) engineers, can offload a RISC workstation of I/O related functions and provide high-performance I/O functions and external interfaces. The high-performance mass storage system has the capabilities to ingest high-speed real-time data, perform signal or image processing, and stage, archive, and distribute the data. This mass storage system uses a hierarchical storage structure, thus reducing the total data storage cost, while maintaining high-I/O performance. The high-performance mass storage system is a network of low-cost parallel processors and storage devices. The nodes in the network have special I/O functions such as: SCSI controller, Ethernet controller, gateway controller, RS232 controller, IEEE488 controller, and digital/analog converter. The nodes are interconnected through high-speed direct memory access links to form a network. The topology of the network is easily reconfigurable to maximize system throughput for various applications. This high-performance mass storage system takes advantage of a 'busless' architecture for maximum expandability. The mass storage system consists of magnetic disks, a WORM optical disk jukebox, and an 8mm helical scan tape to form a hierarchical storage structure. Commonly used files are kept in the magnetic disk for fast retrieval. The optical disks are used as archive media, and the tapes are used as backup media. The storage system is managed by the IEEE mass storage reference model-based UniTree software package. UniTree software will keep track of all files in the system, will automatically migrate the lesser used files to archive media, and will stage the files when needed by the system. The user can access the files without knowledge of their physical location. The high-performance mass storage system developed by Loral AeroSys will significantly boost the system I/O performance and reduce the overall data storage cost. This storage system provides a highly flexible and cost-effective architecture for a variety of applications (e.g., realtime data acquisition with a signal and image processing requirement, long-term data archiving and distribution, and image analysis and enhancement).

Cerebral arterial air embolism in a child after intraosseous infusion

PubMed Central

Knoester, H.; Maes, A.; van der Wal, A. C.; Kubat, B.

2008-01-01

Cerebral arterial air embolism (CAAE) has been reported as a rare complication of medical intervention. There has been one reported case of CAAE after the use of an intraosseous infusion (IO) system. We report on a case of CAAE after tibial IO infusion in a 7-month-old girl during resuscitation. PMID:18247071

A Platform for Learning Internet of Things

ERIC Educational Resources Information Center

Bogdanovic, Zorica; Simic, Konstantin; Milutinovic, Miloš; Radenkovic, Božidar; Despotovic-Zrakic, Marijana

2014-01-01

This paper presents a model for conducting Internet of Things (IoT) classes based on a web-service oriented cloud platform. The goal of the designed model is to provide university students with knowledge about IoT concepts, possibilities, and business models, and allow them to develop basic system prototypes using general-purpose microdevices and…

Performance model-directed data sieving for high-performance I/O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yong; Lu, Yin; Amritkar, Prathamesh

2014-09-10

Many scientific computing applications and engineering simulations exhibit noncontiguous I/O access patterns. Data sieving is an important technique to improve the performance of noncontiguous I/O accesses by combining small and noncontiguous requests into a large and contiguous request. It has been proven effective even though more data are potentially accessed than demanded. In this study, we propose a new data sieving approach namely performance model-directed data sieving, or PMD data sieving in short. It improves the existing data sieving approach from two aspects: (1) dynamically determines when it is beneficial to perform data sieving; and (2) dynamically determines how tomore » perform data sieving if beneficial. It improves the performance of the existing data sieving approach considerably and reduces the memory consumption as verified by both theoretical analysis and experimental results. Given the importance of supporting noncontiguous accesses effectively and reducing the memory pressure in a large-scale system, the proposed PMD data sieving approach in this research holds a great promise and will have an impact on high-performance I/O systems.« less

Visible light communications for the implementation of internet-of-things

NASA Astrophysics Data System (ADS)

Chen, Chia-Wei; Wang, Wei-Chung; Wu, Jhao-Ting; Chen, Hung-Yu; Liang, Kevin; Wei, Liang-Yu; Hsu, Yung; Hsu, Chin-Wei; Chow, Chi-Wai; Yeh, Chien-Hung; Liu, Yang; Hsieh, Hsiang-Chin; Chen, Yen-Ting

2016-06-01

It is predicted that the number of internet-of-things (IoT) devices will be >28 billion in 2020. Due to the shortage of the conventional radio-frequency spectrum, using visible light communication (VLC) for IoT can be promising. IoT networks may only require very low-data rate communication for transmitting sensing or identity information. The implementation of a VLC link on existing computer communication standards and interfaces is important. Among the standards, universal asynchronous receiver/transmitter (UART) is very popular. We propose and demonstrate a VLC-over-UART system. Bit error rate analysis is performed. Different components and modules used in the proposed VLC-over-UART system are discussed. Then, we also demonstrate a real-time simultaneous temperature, humidity, and illuminance monitoring using the proposed VLC link.

Io's Sodium Cloud (Clear Filter and Green-Yellow Filter with Intensity Contours)

NASA Technical Reports Server (NTRS)

1997-01-01

This picture contains two images of Jupiter's moon Io and its surrounding sky. The original frame was exposed twice, once through a clear filter and once through a green-yellow filter. The camera pointed in slightly different directions for the two exposures, placing a clear filter image of Io in the top half of the frame, and a green-yellow filter image of Io in the bottom half of the frame. This picture shows the entire original frame with the addition of intensity contours and false color. East is to the right.

Most of Io's visible surface is in shadow, though part of a white crescent can be seen on its western side. This crescent is being illuminated mostly by 'Jupitershine' (i.e., sunlight reflected off Jupiter). Near Io's eastern equatorial edge is a burst of white light which shows up best in the lower image. This sunlight being scattered by the plume of the volcano Prometheus. Prometheus lies just beyond the visible edge of the moon on Io's far side. Its plume extends about 100 kilometers above the surface, and is being hit by sunlight just a little east of Io's eastern edge.

The sky is full of diffuse light, some of which is scattered light from Prometheus' plume and Io's lit crescent (particularly in the half of the frame dominated by the clear filter). However, much of the diffuse emission comes from Io's Sodium Cloud: sodium atoms within Io's extensive material halo are scattering sunlight into both the clear and green-yellow filters at a wavelength of about 589 nanometers.

The intensity contours help to illustrate that: (i) significant diffuse emission is present all the way to the eastern edge of the frame (indeed, the Sodium Cloud is known to extend far beyond that edge); (ii) the diffuse emission exhibits a directional feature at about four o'clock relative to Io's center (similar features have been seen in the Sodium Cloud at greater distances from Io).

The upper image of Io exhibits a roundish white spot in the bottom half of Io's shadowed side. This corresponds to thermal emission from the volcano Pele. The lower image bears a much smaller trace of this emission because the clear filter is far more sensitive than the green-yellow filter to those relatively long wavelengths where thermal emission is strongest.

This image was taken at 5 hours 30 minutes Universal Time on Nov. 9, 1996 by the solid state imaging (CCD) system aboard NASA's Galileo spacecraft. Galileo was then in Jupiter's shadow, and located about 2.3 million kilometers (about 32 Jovian radii) from both Jupiter and Io.

The Jet Propulsion Laboratory, Pasadena, CA, manages the mission for NASA's Office of Space Science, Washington D.C. This image and other images and data received from Galileo are posted on the World Wide Web Galileo mission home page at: http://galileo.jpl.nasa.gov.

Challenges and Approach for Making the Top End Optical Assembly for the 4-meter Advanced Technology Solar Telescope

NASA Astrophysics Data System (ADS)

Canzian, Blaise; Barentine, J.; Hull, T.

2012-01-01

L-3 Integrated Optical Systems (IOS) Division has been selected by the National Solar Observatory (NSO) to make the Top End Optical Assembly (TEOA) for the 4-meter Advanced Technology Solar Telescope (ATST) to operate at Haleakala, Maui. ATST will perform to a very high optical performance level in a difficult thermal environment. The TEOA, containing the 0.65-meter silicon carbide secondary mirror and support, mirror thermal management system, mirror positioning and fast tip-tilt system, field stop with thermally managed heat dump, thermally managed Lyot stop, safety interlock and control system, and support frame, operates in the "hot spot” at the prime focus of the ATST and so presents special challenges. In this paper, we will describe the L-3 IOS technical approach to meet these challenges, including subsystems for opto-mechanical positioning, rejected and stray light control, wavefront tip-tilt compensation, and thermal management. Key words: ATST, TEOA, L-3 IOS, thermal management, silicon carbide (SiC) mirrors, hexapods, solar astronomy

Completion of the Design of the Top End Optical Assembly for ATST

NASA Astrophysics Data System (ADS)

Canzian, Blaise; Barentine, J.

2013-01-01

L-3 Integrated Optical Systems (IOS) Division has been selected by the National Solar Observatory (NSO) to make the Top End Optical Assembly (TEOA) for the 4-meter Advanced Technology Solar Telescope (ATST) to operate at Haleakala, Maui. ATST will perform to a very high optical performance level in a difficult operational environment. The TEOA (including a 0.65-meter silicon carbide secondary mirror and support, mirror thermal management system, mirror positioning and fast tip-tilt system, field stop with thermally managed heat dump, Lyot stop, safety interlock and control system, and support frame) operates in the “hot spot” at the prime focus of the ATST, presenting unusual challenges. L-3 IOS has passed Critical Design Review of the TEOA. In this paper, we describe L-3 IOS success meeting technical challenges, including our solutions for optic fabrication, opto-mechanical positioning, rejected and stray light control, wavefront tip-tilt compensation, and thermal management and control.

New Process Controls for the Hera Cryogenic Plant

NASA Astrophysics Data System (ADS)

Böckmann, T.; Clausen, M.; Gerke, Chr.; Prüß, K.; Schoeneburg, B.; Urbschat, P.

2010-04-01

The cryogenic plant built for the HERA accelerator at DESY in Hamburg (Germany) is now in operation for more than two decades. The commercial process control system for the cryogenic plant is in operation for the same time period. Ever since the operator stations, the control network and the CPU boards in the process controllers went through several upgrade stages. Only the centralized Input/Output system was kept unchanged. Many components have been running beyond the expected lifetime. The control system for one at the three parts of the cryogenic plant has been replaced recently by a distributed I/O system. The I/O nodes are connected to several Profibus-DP field busses. Profibus provides the infrastructure to attach intelligent sensors and actuators directly to the process controllers which run the open source process control software EPICS. This paper describes the modification process on all levels from cabling through I/O configuration, the process control software up to the operator displays.

Exascale Storage Systems the SIRIUS Way

NASA Astrophysics Data System (ADS)

Klasky, S. A.; Abbasi, H.; Ainsworth, M.; Choi, J.; Curry, M.; Kurc, T.; Liu, Q.; Lofstead, J.; Maltzahn, C.; Parashar, M.; Podhorszki, N.; Suchyta, E.; Wang, F.; Wolf, M.; Chang, C. S.; Churchill, M.; Ethier, S.

2016-10-01

As the exascale computing age emerges, data related issues are becoming critical factors that determine how and where we do computing. Popular approaches used by traditional I/O solution and storage libraries become increasingly bottlenecked due to their assumptions about data movement, re-organization, and storage. While, new technologies, such as “burst buffers”, can help address some of the short-term performance issues, it is essential that we reexamine the underlying storage and I/O infrastructure to effectively support requirements and challenges at exascale and beyond. In this paper we present a new approach to the exascale Storage System and I/O (SSIO), which is based on allowing users to inject application knowledge into the system and leverage this knowledge to better manage, store, and access large data volumes so as to minimize the time to scientific insights. Central to our approach is the distinction between the data, metadata, and the knowledge contained therein, transferred from the user to the system by describing “utility” of data as it ages.

Study of data I/O performance on distributed disk system in mask data preparation

NASA Astrophysics Data System (ADS)

Ohara, Shuichiro; Odaira, Hiroyuki; Chikanaga, Tomoyuki; Hamaji, Masakazu; Yoshioka, Yasuharu

2010-09-01

Data volume is getting larger every day in Mask Data Preparation (MDP). In the meantime, faster data handling is always required. MDP flow typically introduces Distributed Processing (DP) system to realize the demand because using hundreds of CPU is a reasonable solution. However, even if the number of CPU were increased, the throughput might be saturated because hard disk I/O and network speeds could be bottlenecks. So, MDP needs to invest a lot of money to not only hundreds of CPU but also storage and a network device which make the throughput faster. NCS would like to introduce new distributed processing system which is called "NDE". NDE could be a distributed disk system which makes the throughput faster without investing a lot of money because it is designed to use multiple conventional hard drives appropriately over network. NCS studies I/O performance with OASIS® data format on NDE which contributes to realize the high throughput in this paper.

Advanced techniques and armamentarium for dental local anesthesia.

PubMed

Clark, Taylor M; Yagiela, John A

2010-10-01

Computer-controlled local anesthetic delivery (C-CLAD) devices and systems for intraosseous (IO) injection are important additions to the dental anesthesia armamentarium. C-CLAD using slow infusion rates can significantly reduce the discomfort of local anesthetic infusion, especially in palatal tissues, and facilitate palatal approaches to pulpal nerve block that find special use in cosmetic dentistry, periodontal therapy, and pediatric dentistry. Anesthesia of single teeth can be obtained using either C-CLAD intraligamentary injections or IO injections. Supplementary IO anesthesia is particularly suited for providing effective pain control of teeth diagnosed with irreversible pulpitis. Copyright © 2010 Elsevier Inc. All rights reserved.

Using Internet of Things (IoT) technology to study environmental processes

NASA Astrophysics Data System (ADS)

Martinez, Kirk; Hart, Jane; Black, Andrew; Blagg, Olivia

2016-04-01

The Internet of Things is a term which has emerged to describe the increase of Internet connectivity of everyday objects. While wireless sensor networks have developed highly energy efficient designs they need a step-change in their interoperability and usability to become essential tools in the study of our environment. We discuss the design, deployment and results from an IoT system installed on the Cairngorm Plateau, Scotland. This is a fragile remote environment, which provides an ideal location to test IoT techniques. We have investigated cryospheric, hydrologic and ecological processes, and we report our preliminary findings.

12th Annual Systems Engineering Conference

DTIC Science & Technology

2009-10-29

pl em en...io n of Le sso ns L ea rn ed fr om C om pl ex S ys te m o f Sy ste m s A cq ui sit io ns D r. Ri ch ar d Tu rn er , St ev en s I ns tit ut...hn ol og y Tr an sit io n Pl an ni ng Th ro ug h th e U se o f St ag e- G at es – U pd at e M r. R an dy B ul la rd , U .S . A ir Fo

Io Shown in Lambertian Equal Area Projection and in Approximately Natural Color

NASA Image and Video Library

1998-06-04

NASA's Voyager 1 computer color mosaics, shown in approximately natural color and in Lambertian equal-area projections, show the Eastern (left) and Western (right) hemispheres of Io. This innermost of Jupiter's 4 major satellites is the most volcanically active object in the solar system. Io is 2263 mi (3640 km) in diameter, making it a little bigger than Earth's moon. Almost all the features visible here have volcanic origins, including several calderas and eruption plumes that were active at the time of the Voyager 1 encounter. http://photojournal.jpl.nasa.gov/catalog/PIA00318

A Smart and Balanced Energy-Efficient Multihop Clustering Algorithm (Smart-BEEM) for MIMO IoT Systems in Future Networks.

PubMed

Xu, Lina; O'Hare, Gregory M P; Collier, Rem

2017-07-05

Wireless Sensor Networks (WSNs) are typically composed of thousands of sensors powered by limited energy resources. Clustering techniques were introduced to prolong network longevity offering the promise of green computing. However, most existing work fails to consider the network coverage when evaluating the lifetime of a network. We believe that balancing the energy consumption in per unit area rather than on each single sensor can provide better-balanced power usage throughout the network. Our former work-Balanced Energy-Efficiency (BEE) and its Multihop version BEEM can not only extend the network longevity, but also maintain the network coverage. Following WSNs, Internet of Things (IoT) technology has been proposed with higher degree of diversities in terms of communication abilities and user scenarios, supporting a large range of real world applications. The IoT devices are embedded with multiple communication interfaces, normally referred as Multiple-In and Multiple-Out (MIMO) in 5G networks. The applications running on those devices can generate various types of data. Every interface has its own characteristics, which may be preferred and beneficial in some specific user scenarios. With MIMO becoming more available on the IoT devices, an advanced clustering solution for highly dynamic IoT systems is missing and also pressingly demanded in order to cater for differing user applications. In this paper, we present a smart clustering algorithm (Smart-BEEM) based on our former work BEE(M) to accomplish energy efficient and Quality of user Experience (QoE) supported communication in cluster based IoT networks. It is a user behaviour and context aware approach, aiming to facilitate IoT devices to choose beneficial communication interfaces and cluster headers for data transmission. Experimental results have proved that Smart-BEEM can further improve the performance of BEE and BEEM for coverage sensitive longevity.

A Smart and Balanced Energy-Efficient Multihop Clustering Algorithm (Smart-BEEM) for MIMO IoT Systems in Future Networks †

PubMed Central

O’Hare, Gregory M. P.; Collier, Rem

2017-01-01

Wireless Sensor Networks (WSNs) are typically composed of thousands of sensors powered by limited energy resources. Clustering techniques were introduced to prolong network longevity offering the promise of green computing. However, most existing work fails to consider the network coverage when evaluating the lifetime of a network. We believe that balancing the energy consumption in per unit area rather than on each single sensor can provide better-balanced power usage throughout the network. Our former work—Balanced Energy-Efficiency (BEE) and its Multihop version BEEM can not only extend the network longevity, but also maintain the network coverage. Following WSNs, Internet of Things (IoT) technology has been proposed with higher degree of diversities in terms of communication abilities and user scenarios, supporting a large range of real world applications. The IoT devices are embedded with multiple communication interfaces, normally referred as Multiple-In and Multiple-Out (MIMO) in 5G networks. The applications running on those devices can generate various types of data. Every interface has its own characteristics, which may be preferred and beneficial in some specific user scenarios. With MIMO becoming more available on the IoT devices, an advanced clustering solution for highly dynamic IoT systems is missing and also pressingly demanded in order to cater for differing user applications. In this paper, we present a smart clustering algorithm (Smart-BEEM) based on our former work BEE(M) to accomplish energy efficient and Quality of user Experience (QoE) supported communication in cluster based IoT networks. It is a user behaviour and context aware approach, aiming to facilitate IoT devices to choose beneficial communication interfaces and cluster headers for data transmission. Experimental results have proved that Smart-BEEM can further improve the performance of BEE and BEEM for coverage sensitive longevity. PMID:28678164

Spatial Distribution of Volcanic Hotspots and Paterae on Io: Implications for Tidal Heating Models and Magmatic Pathways

NASA Technical Reports Server (NTRS)

Hamilton, C. W.; Beggan, C. D.; Lopes, R.; Williams, D. A.; Radenbaugh, J.

2011-01-01

Io, the innermost of Jupiter's Galilean satellites, is the most volcanically active body in the Solar. System. Io's global mean heat flow is approximately 2 W/square m, which is approximately 20 times larger than on Earth. High surface temperatures concentrate within "hotspots" and, to date, 172 Ionian hotspots have been identified by spacecraft and Earth-based telescopes. The Laplace resonance between Io, Europa, and Ganymede maintains these satellites in noncircular orbits and causes displacement of their tidal bulges as the overhead position of Jupiter changes for each moon. Gravitational interactions between Jupiter and Io dominate the orbital evolution of the Laplacian system and generate enormous heat within to as tidal energy is dissipated. If this energy were transferred out of Io at the same rate as it is generated, then the associated surface heat flux would be 2.24 +/- 0.45 W/square m. This estimate is in good agreement with observed global heat flow, but to better constrain tidal dissipation mechanisms and infer how thermal energy is transferred to Io's surface, it is critical to closely examine the spatial distribution of volcanic features. End-member tidal dissipation models either consider that heating occurs completely in the mantle, or completely in the asthenosphere. Mixed models typically favor one-third mantle and two-thirds asthenosphere heating. Recent models also consider the effects of mantle-asthenosphere boundary permeability and asthenospheric instabilities. Deep-mantle heating models predict maximum surface heat flux near the poles, whereas asthenosphere heating models predict maxima near the equator-particularly in the Sub-Jovian and Anti-Jovian hemispheres, with smaller maxima occurring at orbit tangent longitudes. Previous studies have examined the global distribution of Ionian hotspots and patera (i.e., irregular or complex craters with scalloped edges that are generally interpreted to be volcanic calderas), but in this study, we combine a new geospatial analysis technique with an improved hotspot and paterae database .

X-Ray Probes of Jupiter's Auroral Zones, Galilean Moons, and the Io Plasma Torus

NASA Technical Reports Server (NTRS)

Elsner, R. F.; Ramsey, B. D.; Swartz, D. A.; Rehak, P.; Waite, J. H., Jr.; Cooper, J. F.; Johnson, R. E.

2005-01-01

Remote observations from the Earth orbiting Chandra X-ray Observatory and the XMM-Newton Observatory have shown the the Jovian system is a rich and complex source of x-ray emission. The planet's auroral zones and its disk are powerful sources of x-ray emission, though with different origins. Chandra observations discovered x-ray emission from the Io plasma torus and from the Galilean moons Io, Europa, and possibly Ganymede. The emission from the moons is due to bombardment of their surfaces by highly energetic magnetospheric protons, and oxygen and sulfur ions, producing fluorescent x-ray emission lines from the elements in their surfaces against an intense background continuum. Although very faint when observed from Earth orbit, an imaging x-ray spectrometer in orbit around the icy Galilean moons would provide a detail mapping of the elemental composition in their surfaces. Here we review the results of Chandra and XMM-Newton observations of the Jovian system and describe the characteristics of X-MIME, an imaging x-ray spectrometer undergoing study for possible application to future missions to Jupiter such as JIMO. X-MIME has the ultimate goal of providing detailed high-resolution maps of the elemental abundances of the surfaces of Jupiter's icy moons and Io, as well as detailed study of the x-ray mission from the Io plasma torus, Jupiter's auroral zones, and the planetary disk.

Access Control Mechanism for IoT Environments Based on Modelling Communication Procedures as Resources.

PubMed

Cruz-Piris, Luis; Rivera, Diego; Marsa-Maestre, Ivan; de la Hoz, Enrique; Velasco, Juan R

2018-03-20

Internet growth has generated new types of services where the use of sensors and actuators is especially remarkable. These services compose what is known as the Internet of Things (IoT). One of the biggest current challenges is obtaining a safe and easy access control scheme for the data managed in these services. We propose integrating IoT devices in an access control system designed for Web-based services by modelling certain IoT communication elements as resources. This would allow us to obtain a unified access control scheme between heterogeneous devices (IoT devices, Internet-based services, etc.). To achieve this, we have analysed the most relevant communication protocols for these kinds of environments and then we have proposed a methodology which allows the modelling of communication actions as resources. Then, we can protect these resources using access control mechanisms. The validation of our proposal has been carried out by selecting a communication protocol based on message exchange, specifically Message Queuing Telemetry Transport (MQTT). As an access control scheme, we have selected User-Managed Access (UMA), an existing Open Authorization (OAuth) 2.0 profile originally developed for the protection of Internet services. We have performed tests focused on validating the proposed solution in terms of the correctness of the access control system. Finally, we have evaluated the energy consumption overhead when using our proposal.

Measurements of file transfer rates over dedicated long-haul connections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rao, Nageswara S; Settlemyer, Bradley W; Imam, Neena

2016-01-01

Wide-area file transfers are an integral part of several High-Performance Computing (HPC) scenarios. Dedicated network connections with high capacity, low loss rate and low competing traffic, are increasingly being provisioned over current HPC infrastructures to support such transfers. To gain insights into these file transfers, we collected transfer rate measurements for Lustre and xfs file systems between dedicated multi-core servers over emulated 10 Gbps connections with round trip times (rtt) in 0-366 ms range. Memory transfer throughput over these connections is measured using iperf, and file IO throughput on host systems is measured using xddprof. We consider two file systemmore » configurations: Lustre over IB network and xfs over SSD connected to PCI bus. Files are transferred using xdd across these connections, and the transfer rates are measured, which indicate the need to jointly optimize the connection and host file IO parameters to achieve peak transfer rates. In particular, these measurements indicate that (i) peak file transfer rate is lower than peak connection and host IO throughput, in some cases by as much as 50% or lower, (ii) xdd request sizes that achieve peak throughput for host file IO do not necessarily lead to peak file transfer rates, and (iii) parallelism in host IO and TCP transport does not always improve the file transfer rates.« less

Temporal Informative Analysis in Smart-ICU Monitoring: M-HealthCare Perspective.

PubMed

Bhatia, Munish; Sood, Sandeep K

2016-08-01

The rapid introduction of Internet of Things (IoT) Technology has boosted the service deliverance aspects of health sector in terms of m-health, and remote patient monitoring. IoT Technology is not only capable of sensing the acute details of sensitive events from wider perspectives, but it also provides a means to deliver services in time sensitive and efficient manner. Henceforth, IoT Technology has been efficiently adopted in different fields of the healthcare domain. In this paper, a framework for IoT based patient monitoring in Intensive Care Unit (ICU) is presented to enhance the deliverance of curative services. Though ICUs remained a center of attraction for high quality care among researchers, still number of studies have depicted the vulnerability to a patient's life during ICU stay. The work presented in this study addresses such concerns in terms of efficient monitoring of various events (and anomalies) with temporal associations, followed by time sensitive alert generation procedure. In order to validate the system, it was deployed in 3 ICU room facilities for 30 days in which nearly 81 patients were monitored during their ICU stay. The results obtained after implementation depicts that IoT equipped ICUs are more efficient in monitoring sensitive events as compared to manual monitoring and traditional Tele-ICU monitoring. Moreover, the adopted methodology for alert generation with information presentation further enhances the utility of the system.

Access Control Mechanism for IoT Environments Based on Modelling Communication Procedures as Resources

PubMed Central

2018-01-01

Internet growth has generated new types of services where the use of sensors and actuators is especially remarkable. These services compose what is known as the Internet of Things (IoT). One of the biggest current challenges is obtaining a safe and easy access control scheme for the data managed in these services. We propose integrating IoT devices in an access control system designed for Web-based services by modelling certain IoT communication elements as resources. This would allow us to obtain a unified access control scheme between heterogeneous devices (IoT devices, Internet-based services, etc.). To achieve this, we have analysed the most relevant communication protocols for these kinds of environments and then we have proposed a methodology which allows the modelling of communication actions as resources. Then, we can protect these resources using access control mechanisms. The validation of our proposal has been carried out by selecting a communication protocol based on message exchange, specifically Message Queuing Telemetry Transport (MQTT). As an access control scheme, we have selected User-Managed Access (UMA), an existing Open Authorization (OAuth) 2.0 profile originally developed for the protection of Internet services. We have performed tests focused on validating the proposed solution in terms of the correctness of the access control system. Finally, we have evaluated the energy consumption overhead when using our proposal. PMID:29558406

Three decades of Loki Patera observations

NASA Astrophysics Data System (ADS)

de Pater, Imke; de Kleer, Katherine; Davies, Ashley G.; Ádámkovics, Máté

2017-11-01

We present observations of Io's Loki Patera taken with the 10-m Keck telescopes between 1998 and 2016. Adding these data to those published by Rathbun and Spencer (2006) and the Gemini data of de Kleer and de Pater (2016a, 2017) results in a database of 3.5-3.8 μm emission from Loki Patera over almost 3 decades. Data presented here contain adaptive optics (AO) observations of Io's sunlit hemisphere at wavelengths between 1.6 and 5 μm, AO observations of Io in eclipse at 2-5 μm, and non-AO observations of Io in eclipse at 1.6-12 μm. The non-AO data were taken in September of 1999, during the early phase of a brightening event that was documented by Howell et al. (2001). Dual-component Io Flow model (IFM) fits to our 1999 observations show a mostly cool lava crust over almost the entire patera floor, with a relatively small hotter component making up less than 1% of the total area, consistent with previous observations. The 30-year timeline of Loki Patera revealed that, after an apparent cessation of, or change in, brightening events in 2002, Loki Patera became active again in 2009. The more recent activity may have a slightly shorter periodicity than observed by Rathbun et al. (2002), and the direction of flow propagation appears to have reversed. Since 2009 the flow direction is in the clockwise direction, starting in the north or north-east corner and propagating along the patera towards the south-west. During the Galileo era the propagation was in the counter-clockwise direction, starting in the south-west and propagating towards the east. Both the 30-year timeline and the 1.6-12 μm spectrum that was obtained during the brightening event in 1999 agree well with Matson et al.'s (2006) overturning lava lake model, as modified by de Kleer and de Pater (2017).

InvestigationOrganizer: The Development and Testing of a Web-based Tool to Support Mishap Investigations

NASA Technical Reports Server (NTRS)

Carvalho, Robert F.; Williams, James; Keller, Richard; Sturken, Ian; Panontin, Tina

2004-01-01

InvestigationOrganizer (IO) is a collaborative web-based system designed to support the conduct of mishap investigations. IO provides a common repository for a wide range of mishap related information, and allows investigators to make explicit, shared, and meaningful links between evidence, causal models, findings and recommendations. It integrates the functionality of a database, a common document repository, a semantic knowledge network, a rule-based inference engine, and causal modeling and visualization. Thus far, IO has been used to support four mishap investigations within NASA, ranging from a small property damage case to the loss of the Space Shuttle Columbia. This paper describes how the functionality of IO supports mishap investigations and the lessons learned from the experience of supporting two of the NASA mishap investigations: the Columbia Accident Investigation and the CONTOUR Loss Investigation.

The application of the Internet of Things to animal ecology.

PubMed

Guo, Songtao; Qiang, Min; Luan, Xiaorui; Xu, Pengfei; He, Gang; Yin, Xiaoyan; Xi, Luo; Jin, Xuelin; Shao, Jianbin; Chen, Xiaojiang; Fang, Dingyi; Li, Baoguo

2015-11-01

For ecologists, understanding the reaction of animals to environmental changes is critical. Using networked sensor technology to measure wildlife and environmental parameters can provide accurate, real-time and comprehensive data for monitoring, research and conservation of wildlife. This paper reviews: (i) conventional detection technology; (ii) concepts and applications of the Internet of Things (IoT) in animal ecology; and (iii) the advantages and disadvantages of IoT. The current theoretical limits of IoT in animal ecology are also discussed. Although IoT offers a new direction in animal ecological research, it still needs to be further explored and developed as a theoretical system and applied to the appropriate scientific frameworks for understanding animal ecology. © 2015 International Society of Zoological Sciences, Institute of Zoology/Chinese Academy of Sciences and Wiley Publishing Asia Pty Ltd.

Versatile simulation testbed for rotorcraft speech I/O system design

NASA Technical Reports Server (NTRS)

Simpson, Carol A.

1986-01-01

A versatile simulation testbed for the design of a rotorcraft speech I/O system is described in detail. The testbed will be used to evaluate alternative implementations of synthesized speech displays and speech recognition controls for the next generation of Army helicopters including the LHX. The message delivery logic is discussed as well as the message structure, the speech recognizer command structure and features, feedback from the recognizer, and random access to controls via speech command.

NASA Tropospheric Composition Program field campagins as prototypes to advance the Integrated Observing System for Air Quality

NASA Astrophysics Data System (ADS)

Lefer, B. L.; Crawford, J. H.; Pierce, R. B.; Berkoff, T.; Swap, R.; Janz, S. J.; Ahn, J.; Al-Saadi, J. A.

2017-12-01

With the launch over the virtual constellation of earth observing satellites for atmospheric composition (e.g., TROPOMI, GEMS, TEMPO, and Sentinel-4) over the next several years, we have a unique opportunity to develop an Integrated Observing System (IOS) for air quality in the northern hemisphere. Recently, NASA's Tropospheric Composition Program (TCP) has participated in several different air quality related field campaigns as an effort to explore various prototypes of the IOS for Air Quality. The IOS for air quality could be a system were space-based observations of air quality (generally, column abundances of NO2, HCHO, O3, SO2, and AOD) are given added "value" by being integrated with: a) long-term ground-based observations;b) regional and global air quality and chemical transport models; as well as c) measurements from targeted airborne field campaigns. The recent Korea-US Air Quality Study (KORUS-AQ), the Lake Michigan Ozone Study 2017 (LMOS), and the Ozone Water-Land Environmental Transition Study (OWLETS) field campaigns were held in different locations and made measurements over different scale. However, all of these provide an opportunity to learn about how a future integrated air quality observing system can be implemented to serve a variety of air quality related objectives. NASA TCP is also exploring enchancements to our routine observations to strengthen the IOS for air quality in the future.

Navigated Pattern Laser System versus Single-Spot Laser System for Postoperative 360-Degree Laser Retinopexy.

PubMed

Kulikov, Alexei N; Maltsev, Dmitrii S; Boiko, Ernest V

2016-01-01

Purpose . To compare three 360°-laser retinopexy (LRP) approaches (using navigated pattern laser system, single-spot slit-lamp (SL) laser delivery, and single-spot indirect ophthalmoscope (IO) laser delivery) in regard to procedure duration, procedural pain score, technical difficulties, and the ability to achieve surgical goals. Material and Methods . Eighty-six rhegmatogenous retinal detachment patients (86 eyes) were included in this prospective randomized study. The mean procedural time, procedural pain score (using 4-point Verbal Rating Scale), number of laser burns, and achievement of the surgical goals were compared between three groups (pattern LRP (Navilas® laser system), 36 patients; SL-LRP, 28 patients; and IO-LRP, 22 patients). Results . In the pattern LRP group, the amount of time needed for LRP and pain level were statistically significantly lower, whereas the number of applied laser burns was higher compared to those in the SL-LRP group and in the IO-LRP group. In the pattern LRP, SL-LRP, and IO-LRP groups, surgical goals were fully achieved in 28 (77.8%), 17 (60.7%), and 13 patients (59.1%), respectively ( p > 0.05). Conclusion . The navigated pattern approach allows improving the treatment time and pain in postoperative 360° LRP. Moreover, 360° pattern LRP is at least as effective in achieving the surgical goal as the conventional (slit-lamp or indirect ophthalmoscope) approaches with a single-spot laser.

Enhancing Human-Machine System Performance by Introducing Artificial Cognition in Vehicle Guidance Work Systems

DTIC Science & Technology

2009-10-01

evaluated after each mission using the NASA - TLX method [21]. Moreover, they were interviewed to be able to state problems and suggest system...France, 3 rd -4 th September 2008. [21] Sandra G. Hart & Lowell E. Staveland (1988). Development of NASA - TLX (Task Load Index): Results of...o b s e rv a b le b e h a v io u r o f C P = A C U b e h a v io u r Interpretation Figure 11: The Cognitive Process for generating knowledge

Measurements of the dissolved inorganic carbon system and associated biogeochemical parameters in the Canadian Arctic, 1974-2009

NASA Astrophysics Data System (ADS)

Giesbrecht, K. E.; Miller, L. A.; Davelaar, M.; Zimmermann, S.; Carmack, E.; Johnson, W. K.; Macdonald, R. W.; McLaughlin, F.; Mucci, A.; Williams, W. J.; Wong, C. S.; Yamamoto-Kawai, M.

2014-03-01

We have assembled and conducted primary quality control on previously publicly unavailable water column measurements of the dissolved inorganic carbon system and associated biogeochemical parameters (oxygen, nutrients, etc.) made on 26 cruises in the subarctic and Arctic regions dating back to 1974. The measurements are primarily from the western side of the Canadian Arctic, but also include data that cover an area ranging from the North Pacific to the Gulf of St. Lawrence. The data were subjected to primary quality control (QC) to identify outliers and obvious errors. This data set incorporates over four thousand individual measurements of total inorganic carbon (TIC), alkalinity, and pH from the Canadian Arctic over a period of more than 30 years and provides an opportunity to increase our understanding of temporal changes in the inorganic carbon system in northern waters and the Arctic Ocean. The data set is available for download on the CDIAC (Carbon Dioxide Information Analysis Center) website: http://cdiac.ornl.gov/ftp/oceans/IOS_Arctic_Database/ (doi:10.3334/CDIAC/OTG.IOS_ARCT_CARBN).

Io Science Opportunities From the JIMO Mission

NASA Astrophysics Data System (ADS)

Bills, B. G.; Ray, R. D.; Spencer, J. R.; Lopes, R.; Smythe, W. D.

2003-12-01

Io is the only place beyond Earth where we can watch geological processes in action. It has much to teach us about large-scale volcanic processes in general, the history of the early Earth, which at one time may have had a heat flow approaching Io's 2 -- 3 W m-2, and the nature of tidal heating in the Jupiter system and beyond. Though the nominal mission of the proposed Jupiter Icy Moons Orbiter (JIMO) does not include close approaches to Io, the mission can still make unique and important contributions to the understanding of Io and its active volcanism. Dynamic volcanic phenomena (e.g., active lava flows and pyroclastic events) typically evolve on timescales of hours to weeks and on spatial scales up to tens of kilometers. However, existing coverage of Io does not cover this range of spatial and temporal scales, and thus has provided very limited ability to watch volcanic activity as it happens. Galileo provided spatial resolution down to a few meters but temporal resolution no better than a few months, and Earth-based techniques provide temporal resolution down to hours or days but spatial resolution no better than ˜ 100 km. A 0.5 meter aperture telescope on JIMO could image Io from the distance of Ganymede with diffraction-limited resolution ranging from 1 km in the visible to 25 km at 10 μ m. Io observations could be concentrated in the several-month periods of Jovicentric orbit while JIMO transfers between icy satellite orbits, causing minimal interruption to JIMO's icy satellite mapping program. If JIMO has a scan platform capable of rapid pointing, full-disk observations of Io could be taken as frequently as once per hour, for example, interleaved with observations of other targets such as Jupiter and long-range observations of the icy satellites. Io-optimized instrumentation would include the following: (i) A 0.2 -- 0.3 μ m spectrograph for mapping atmospheric SO2 and other species; (ii) Visible imaging in several broadband and narrowband filters from 0.35 -- 1.0 μ m, for geomorphology and observations of plumes and pyroclastic deposits, and atmospheric emissions in eclipse; (iii) A 1 -- 5 μ m spectrograph for both reflectance spectroscopy of surface species and measurements of the temperature and area of hot volcanic materials via their thermal emission; and (iv) thermal infrared imaging in several broadband filters from 5 -- 30 μ m, for studies of lava flow cooling, surface thermal inertia, and global heat flow. With this instrumentation we could watch the complete evolution of several major eruptions on Io over the course of the JIMO mission. Science results would include, for example: (i) Magmatic temperatures during the early phases of major eruptions, providing critical constraints on magma composition and Io's interior structure; (ii) Rates of supply of gas from volcanic eruptions to Io's atmosphere, and condensed volatiles to its surface; (iii) The influence of major eruptions on Jupiter's magnetosphere, using other magnetospheric observations from JIMO; (iv) Rates of magma generation, providing constraints on volcanic "plumbing" and lava composition; (v) Accurate measurement of Io's endogenic heat flow and its spatial distribution, with implications for understanding Io's interior structure and the orbital and tidal evolution of all the Galilean satellites. While science return would be even greater if JIMO was able to approach Io closely, huge advances in our understanding of Io will be possible even from relatively distant observations, if Io science is given sufficient priority in the planning of JIMO's instrumentation and observations.

Nanosatellites constellation as an IoT communication platform for near equatorial countries

NASA Astrophysics Data System (ADS)

Narayanasamy, A.; Ahmad, Y. A.; Othman, M.

2017-11-01

Anytime, anywhere access for real-time intelligence by Internet of Things (IoT) is changing the way that the whole world will operate as it moves toward data driven technologies. Over the next five years, IoT related devices going to have a dramatic breakthrough in current and new applications, not just on increased efficiency and cost reduction on current system, but it also will make trillion-dollar revenue generation and improve customer satisfaction. IoT communications is the networking of intelligent devices which enables data collection from remote assets. It covers a broad range of technologies and applications which connect to the physical world while allowing key information to be transferred automatically. The current terrestrial wireless communications technologies used to enable this connectivity include GSM, GPRS, 3G, LTE, WIFI, WiMAX and LoRa. These connections occur short to medium range distance however, none of them can cover a whole country or continent and the networks are getting congested with the multiplication of IoT devices. In this study, we discuss a conceptual design of a nanosatellite constellation those can provide a space-based communication platform for IoT devices for near Equatorial countries. The constellation design i.e. the orbital plane and number of satellites and launch deployment concepts are presented.

Proof of Concept of Home IoT Connected Vehicles

PubMed Central

Kim, Younsun; Oh, Hyunggoy; Kang, Sungho

2017-01-01

The way in which we interact with our cars is changing, driven by the increased use of mobile devices, cloud-based services, and advanced automotive technology. In particular, the requirements and market demand for the Internet of Things (IoT) device-connected vehicles will continuously increase. In addition, the advances in cloud computing and IoT have provided a promising opportunity for developing vehicular software and services in the automotive domain. In this paper, we introduce the concept of a home IoT connected vehicle with a voice-based virtual personal assistant comprised of a vehicle agent and a home agent. The proposed concept is evaluated by implementing a smartphone linked with home IoT devices that are connected to an infotainment system for the vehicle, a smartphone-based natural language interface input device, and cloud-based home IoT devices for the home. The home-to-vehicle connected service scenarios that aim to reduce the inconvenience due to simple and repetitive tasks by improving the urban mobility efficiency in IoT environments are substantiated by analyzing real vehicle testing and lifestyle research. Remarkable benefits are derived by making repetitive routine tasks one task that is executed by a command and by executing essential tasks automatically, without any request. However, it should be used with authorized permission, applied without any error at the right time, and applied under limited conditions to sense the habitants’ intention correctly and to gain the required trust regarding the remote execution of tasks. PMID:28587246

Proof of Concept of Home IoT Connected Vehicles.

PubMed

Kim, Younsun; Oh, Hyunggoy; Kang, Sungho

2017-06-05

The way in which we interact with our cars is changing, driven by the increased use of mobile devices, cloud-based services, and advanced automotive technology. In particular, the requirements and market demand for the Internet of Things (IoT) device-connected vehicles will continuously increase. In addition, the advances in cloud computing and IoT have provided a promising opportunity for developing vehicular software and services in the automotive domain. In this paper, we introduce the concept of a home IoT connected vehicle with a voice-based virtual personal assistant comprised of a vehicle agent and a home agent. The proposed concept is evaluated by implementing a smartphone linked with home IoT devices that are connected to an infotainment system for the vehicle, a smartphone-based natural language interface input device, and cloud-based home IoT devices for the home. The home-to-vehicle connected service scenarios that aim to reduce the inconvenience due to simple and repetitive tasks by improving the urban mobility efficiency in IoT environments are substantiated by analyzing real vehicle testing and lifestyle research. Remarkable benefits are derived by making repetitive routine tasks one task that is executed by a command and by executing essential tasks automatically, without any request. However, it should be used with authorized permission, applied without any error at the right time, and applied under limited conditions to sense the habitants' intention correctly and to gain the required trust regarding the remote execution of tasks.

Cassini Imaging of Io's Visible Aurora

NASA Astrophysics Data System (ADS)

Geissler, P.; McEwen, A.; Porco, C.; Strobel, D.; Saur, J.; Ajello, J.

2003-04-01

Io is the only moon in the solar system known to display visible atmospheric emissions that would be bright enough to be seen with the naked eye by a hypothetical human visitor to the jovian system. Earlier imaging of Io's colorful aurorae [1,2,3], obtained by the Galileo spacecraft while the satellite was in eclipse, left a number of questions unanswered. The temporal behavior of the emissions was difficult to discern from the occasional glimpses afforded by Galileo. The identities of the emitting species were poorly known. Unlike the far-ultraviolet emissions from Io's atmosphere that closely tracked the tangent points of Jupiter's magnetic field lines [5,6], the brightest visible glows were clearly linked to actively erupting volcanic plumes. Cassini, with its fully functioning high-gain antenna, near-ultraviolet sensitivity and better spectral resolution, was able to fill many of the gaps in our knowledge of these mysterious phenomena [6]. Cassini monitored Io's appearance over entire eclipses, documenting temporal changes on time scales of minutes. These data help constrain the degree of atmospheric collapse during eclipse and establish the relationship of the emissions to the changing orientation of the jovian magnetic field. Cassini detected glows at previously unknown wavelengths, providing new evidence of molecular SO2 emission and other atmospheric constituents. The spatial distribution of the glows indicates the presence of a giant volcanic plume near Io's north pole at the time of the observations and also reveals stratification of the satellite's tenuous atmosphere. [1] McEwen et al., Icarus 135, 181, 1998. [2] Geissler et al., Science 285, 870, 1999. [3] Geissler et al., JGR 106, 26137, 2001. [4] Roesler et al., Science 283, 353, 1999. [5] Retherford et al., JGR 105, 27157, 2000. [6] Porco et al., Science, in prep. 2003.

Iodine binding to humic acid.

PubMed

Bowley, H E; Young, S D; Ander, E L; Crout, N M J; Watts, M J; Bailey, E H

2016-08-01

The rate of reactions between humic acid (HA) and iodide (I(-)) and iodate (IO3(-)) have been investigated in suspensions spiked with (129)I at concentrations of 22, 44 and 88 μg L(-1) and stored at 10 °C. Changes in the speciation of (129)I(-), (129)IO3(-) and mixed ((129)I(-) + (129)IO3(-)) spikes were monitored over 77 days using liquid chromatography inductively coupled plasma mass spectrometry (LC-ICP-MS). In suspensions spiked with (129)I(-) 25% of the added I(-) was transformed into organic iodine (Org-(129)I) within 77 days and there was no evidence of (129)IO3(-) formation. By contrast, rapid loss of (129)IO3(-) and increase in both (129)I(-) and Org-(129)I was observed in (129)IO3(-)-spiked suspensions. However, the rate of Org-(129)I production was greater in mixed systems compared to (129)IO3(-)-spiked suspensions with the same total (129)I concentration, possibly indicating IO3(-)I(-) redox coupling. Size exclusion chromatography (SEC) demonstrated that Org-(129)I was present in both high and low molecular weight fractions of the HA although a slight preference to bond with the lower molecular weight fractions was observed indicating that, after 77 days, the spiked isotope had not fully mixed with the native (127)I pool. Iodine transformations were modelled using first order rate equations and fitted rate coefficients determined. However, extrapolation of the model to 250 days indicated that a pseudo-steady state would be attained after ∼200 days but that the proportion of (129)I incorporated into HA was less than that of (127)I indicating the presence of a recalcitrant pool of (127)I that was unavailable for isotopic mixing. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Intersection of Robust Intelligence and Trust: Hybrid Teams, Firms, and Systems

DTIC Science & Technology

2014-01-01

bites dogma: Apple’s iOS ate up Android, Blackberry U.S. market share losses this summer”; http://appleinsider.com/articles/13/10/05/data-bites-dogma...ios-ate-up-android- blackberry -us-market-share-losses-this- summer 9 Compare night satellite photos of the USA with Cuba; or South Korea with North

General Electromagnetic Model for the Analysis of Complex Systems (GEMACS) Engineering Manual (Version 3). Volume 3.

DTIC Science & Technology

1983-09-01

processor. How- ever, upon completion of the restart initialization, additional commands may be added or original commands deleted with normal input...written IOSI Scratch logical unit designator IOS1SV Saved value of lOS1 IOS2 Scratch logical unit designator IR Index pointer to upper triangular matrix

Science Measurements for the Io Volcano Observer (IVO)

NASA Astrophysics Data System (ADS)

McEwen, A. S.; Turtle, E. P.; Lorenz, R. D.; Perry, J.; Spencer, J. R.; Kirk, R. L.; Keszthelyi, L. P.; Davies, A. G.; Khurana, K. K.; Jia, X.; Moses, J. I.; Paranicas, C.; Hamilton, C.; Nimmo, F.; Showman, A. P.; Thomas, N.; Wurz, P.; Barabash, S. V.; Wieser, M.; Spohn, T.; Horst, S. M.; Breuer, D.; Iess, L.; Helbert, J.; Heyner, D.; Humm, D. C.; De Pater, I.; Mousis, O.; Bagenal, F.; Sutton, S.; Hibbard, K.; Reynolds, E.; Glassmeier, K. H.

2015-12-01

Proposed for Discovery in 2015, IVO would launch in 2021, arrive at Jupiter in early 2026, and perform at least 9 fast flybys of Io. IVO satisfies the key science objectives of the Io Observer concept for New Frontiers. Science instruments include Narrow- and wide-angle cameras (from APL and UA), dual fluxgate magnetometers (UCLA), thermal mapper (DLR-Germany), ion and neutral mass spectrometer (UBE-Switzerland), and plasma ion analyzer (IRF-Sweden). For more on the mission see http://www.lpi.usra.edu/opag/meetings/feb2015/presentations/. Key measurements include: 1. High-resolution (<20 m/pixel) imaging of volcanic landforms and vent structures; 2. Regional surface changes every encounter; 3. Velocities and effusion rates of dynamic processes; 4. Mapping of 150 K to ≥1000 K surfaces at 0.5-20 km/pixel for volcanic history; 5. Peak color temperature of erupting lavas; 6. Melt fraction of the mantle from electromagnetic sounding; 7. Thickness of Io's lithosphere; 8. Constraints on Io's internal magnetic field; 9. Global pattern of endogenic heat flow driven by tidal heating; 10. Regional topographic anomalies; 11. Tidal k2 to constrain mantle rigidity; 12. Topography of tectonic landforms; 13. Structural changes since Voyager and Galileo imaging; 14. Neutral species in Io's atmosphere and exosphere; 15. SO2, OI, and other emissions (in eclipse); 16. Christiansen Frequency (CF) to constrain SiO2 of warm silicate lavas; 17. Surface color variations from 300-1000 nm; 18. Passive background temperatures to model diurnal T variations; 19. Neutral species in Io's vicinity; 20. Remote monitoring of Na cloud and Io Plasma Torus; 21. Variability of plasma and magnetic signatures; 22. Search for plumes on Europa's bright limb at high phase angles; and 23. Monitor Europa's surface color and albedo for changes. In summary, IVO will acquire a broad suite of measurements to understand how tidal heating drives dynamic phenomena on Io and in the Jupiter system.

Automation of Educational Tasks for Academic Radiology.

PubMed

Lamar, David L; Richardson, Michael L; Carlson, Blake

2016-07-01

The process of education involves a variety of repetitious tasks. We believe that appropriate computer tools can automate many of these chores, and allow both educators and their students to devote a lot more of their time to actual teaching and learning. This paper details tools that we have used to automate a broad range of academic radiology-specific tasks on Mac OS X, iOS, and Windows platforms. Some of the tools we describe here require little expertise or time to use; others require some basic knowledge of computer programming. We used TextExpander (Mac, iOS) and AutoHotKey (Win) for automated generation of text files, such as resident performance reviews and radiology interpretations. Custom statistical calculations were performed using TextExpander and the Python programming language. A workflow for automated note-taking was developed using Evernote (Mac, iOS, Win) and Hazel (Mac). Automated resident procedure logging was accomplished using Editorial (iOS) and Python. We created three variants of a teaching session logger using Drafts (iOS) and Pythonista (iOS). Editorial and Drafts were used to create flashcards for knowledge review. We developed a mobile reference management system for iOS using Editorial. We used the Workflow app (iOS) to automatically generate a text message reminder for daily conferences. Finally, we developed two separate automated workflows-one with Evernote (Mac, iOS, Win) and one with Python (Mac, Win)-that generate simple automated teaching file collections. We have beta-tested these workflows, techniques, and scripts on several of our fellow radiologists. All of them expressed enthusiasm for these tools and were able to use one or more of them to automate their own educational activities. Appropriate computer tools can automate many educational tasks, and thereby allow both educators and their students to devote a lot more of their time to actual teaching and learning. Copyright © 2016 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

The Design and Semi-Physical Simulation Test of Fault-Tolerant Controller for Aero Engine

NASA Astrophysics Data System (ADS)

Liu, Yuan; Zhang, Xin; Zhang, Tianhong

2017-11-01

A new fault-tolerant control method for aero engine is proposed, which can accurately diagnose the sensor fault by Kalman filter banks and reconstruct the signal by real-time on-board adaptive model combing with a simplified real-time model and an improved Kalman filter. In order to verify the feasibility of the method proposed, a semi-physical simulation experiment has been carried out. Besides the real I/O interfaces, controller hardware and the virtual plant model, semi-physical simulation system also contains real fuel system. Compared with the hardware-in-the-loop (HIL) simulation, semi-physical simulation system has a higher degree of confidence. In order to meet the needs of semi-physical simulation, a rapid prototyping controller with fault-tolerant control ability based on NI CompactRIO platform is designed and verified on the semi-physical simulation test platform. The result shows that the controller can realize the aero engine control safely and reliably with little influence on controller performance in the event of fault on sensor.

Neutral Beam Injection System for the SHIP Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abdrashitov, G.F.; Abdrashitov, A.G.; Anikeev, A.V.

2005-01-15

The injector ion source is based on an arcdischarge plasma box. The plasma emitter is produced by a 1 kA arc discharge in deuterium. A multipole magnetic field produced with permanent magnets at the periphery of the plasma box is used to increase its efficiency and improve homogeneity of the plasma emitter. The ion beam is extracted by a 4-electrodes ion optical system (IOS). Initial beam diameter is 200 mm. The grids of the IOS have a spherical curvature for geometrical focusing of the beam. The optimal IOS geometry and grid potentials were found by means of numerical simulation tomore » provide precise beam formation. The measured angular divergence of the beam is 0.025 rad, which corresponds to a 4.7 cm Gaussian radius of the beam profile measured at focal point.« less

Observing iodine monoxide from satellite

NASA Astrophysics Data System (ADS)

Schoenhardt, Anja; Richter, Andreas; Begoin, Mathias; Wittrock, Folkard; Burrows, John P.

Iodine and iodine monoxide (IO) belong to the group of reactive halogen species, and they may impact on atmospheric chemical composition and the radiation budget. Vice versa, sur-rounding conditions may influence the emissions and pathways of iodine compounds. Although atmospheric amounts of iodine are typically fairly small, the impact may still be substantial. Iodine radicals are photolytically released from precursors and may then cause catalytic ozone depletion. In this reaction with ozone, IO is produced, a molecule which plays a central role in the iodine cycling. Via self reactions of IO, higher iodine oxides form and initiate the formation of new particles, which may change the atmospheric radiation balance. Apart from that, many living species, including human beings, vertebrates in general, but also micro-and macroalgae species, e.g., depend on the supply with iodine. Consequently, it is necessary to understand the cycling of iodine through the different components of the Earth system. Although increas-ing research effort in the form of field, laboratory and modeling studies has strongly improved our knowledge and understanding of iodine abundances and impact, still many open questions remain. The relevance of iodine on a global scale is not well known yet; sources are not well quantified and release processes are not fully understood. Since recently, IO may be observed from space by the SCIAMACHY instrument on the EN-VISAT satellite, which is in a near-polar, sun-synchronous orbit. Nadir observations from SCIAMACHY have been analysed for the IO absorption signature in the visible wavelength range for several mission years. IO amounts are typically close to the limit of detectability of SCIAMACHY. Detecting such small quantities, careful attention needs to be paid to system-atic errors, spectral correlations and resulting retrieval artefacts. Subsequently, appropriate temporal averaging is utilised to improve the signal-to-noise ratio. The resulting observations allow the identification of regions with enhanced IO amounts and yield new insight into the spatial and temporal distribution of IO on Earth. While SCIAMACHY is the only satellite instrument, for which IO detection has been successful up to now, the observation of iodine species with further space instrumentation might become possible in the future. The presented work covers several interesting regions, mainly the Southern Hemispheric Polar Region, where details on the distribution and variability of IO over the Antarctic are revealed, but also the tropical Pacific and some Northern Hemispheric coast lines. In some cases, con-nections between the biosphere and the observed iodine species are likely. Interestingly, the distributions of IO differ quite strongly from those of bromine monoxide. The findings give indications for different release pathways of bromine and iodine species. In addition, some suspected differences between the Northern and the Southern Hemisphere in iodine abundance are supported. Studies on specifically interesting regions are presented, and the connections to potential iodine sources are discussed.

Tvashtar in Motion

NASA Technical Reports Server (NTRS)

2007-01-01

This five-frame sequence of New Horizons images captures the giant plume from Io's Tvashtar volcano. Snapped by the probe's Long Range Reconnaissance Imager (LORRI) as the spacecraft flew past Jupiter earlier this year, this first-ever 'movie' of an Io plume clearly shows motion in the cloud of volcanic debris, which extends 330 kilometers (200 miles) above the moon's surface. Only the upper part of the plume is visible from this vantage point -- the plume's source is 130 kilometers (80 miles) below the edge of Io's disk, on the far side of the moon.

The appearance and motion of the plume is remarkably similar to an ornamental fountain on Earth, replicated on a gigantic scale. The knots and filaments that allow us to track the plume's motion are still mysterious, but this movie is likely to help scientists understand their origin, as well as provide unique information on the plume dynamics.

Io's hyperactive nature is emphasized by the fact that two other volcanic plumes are also visible off the edge of Io's disk: Masubi at the 7 o'clock position, and a very faint plume, possibly from the volcano Zal, at the 10 o'clock position. Jupiter illuminates the night side of Io, and the most prominent feature visible on the disk is the dark horseshoe shape of the volcano Loki, likely an enormous lava lake. Boosaule Mons, which at 18 kilometers (11 miles) is the highest mountain on Io and one of the highest mountains in the solar system, pokes above the edge of the disk on the right side.

The five images were obtained over an 8-minute span, with two minutes between frames, from 23:50 to 23:58 Universal Time on March 1, 2007. Io was 3.8 million kilometers (2.4 million miles) from New Horizons; the image is centered at Io coordinates 0 degrees north, 342 degrees west.

The pictures were part of a sequence designed to look at Jupiter's rings, but planners included Io in the sequence because the moon was passing behind Jupiter's rings at the time.

Bi2(IO3)(IO6): First combination of [IO3]- and [IO6]5- anions in three-dimensional framework

NASA Astrophysics Data System (ADS)

Sun, Chuanling; Wu, Yuandong; Mei, Dajiang; Doert, Thomas

2018-03-01

A new bismuth (III) iodate periodate, Bi2(IO3)(IO6) was obtained from hydrothermal reactions using Bi(NO3)3·5H2O, and H5IO6 as starting materials. Bi2(IO3)(IO6) crystallizes in the monoclinic space group P21/c (No. 14) with lattice parameters ɑ = 8.1119(6), b = 5.4746(4), c = 16.357(1) Å, β = 99.187(2)°, V = 717.07(9) Å3, Z = 4. The structure of Bi2(IO3)(IO6) features a three-dimensional framework which is a combination of [Bi(1)O5] tetragonal pyramids, [Bi(2)O8] bicapped trigonal prisms and [IO3]- and [IO6]5- anions. Thermal analysis shows that the compound is thermally stable up to about 350 °C. The solid state UV-vis-NIR diffuse reflectance spectrum indicates that Bi2(IO3)(IO6) is a semiconductor with a band gap of 2.76 eV.

Collaborative Working Architecture for IoT-Based Applications.

PubMed

Mora, Higinio; Signes-Pont, María Teresa; Gil, David; Johnsson, Magnus

2018-05-23

The new sensing applications need enhanced computing capabilities to handle the requirements of complex and huge data processing. The Internet of Things (IoT) concept brings processing and communication features to devices. In addition, the Cloud Computing paradigm provides resources and infrastructures for performing the computations and outsourcing the work from the IoT devices. This scenario opens new opportunities for designing advanced IoT-based applications, however, there is still much research to be done to properly gear all the systems for working together. This work proposes a collaborative model and an architecture to take advantage of the available computing resources. The resulting architecture involves a novel network design with different levels which combines sensing and processing capabilities based on the Mobile Cloud Computing (MCC) paradigm. An experiment is included to demonstrate that this approach can be used in diverse real applications. The results show the flexibility of the architecture to perform complex computational tasks of advanced applications.

Constructing Topic Models of Internet of Things for Information Processing

PubMed Central

Xin, Jie; Cui, Zhiming; Zhang, Shukui; He, Tianxu; Li, Chunhua; Huang, Haojing

2014-01-01

Internet of Things (IoT) is regarded as a remarkable development of the modern information technology. There is abundant digital products data on the IoT, linking with multiple types of objects/entities. Those associated entities carry rich information and usually in the form of query records. Therefore, constructing high quality topic hierarchies that can capture the term distribution of each product record enables us to better understand users' search intent and benefits tasks such as taxonomy construction, recommendation systems, and other communications solutions for the future IoT. In this paper, we propose a novel record entity topic model (RETM) for IoT environment that is associated with a set of entities and records and a Gibbs sampling-based algorithm is proposed to learn the model. We conduct extensive experiments on real-world datasets and compare our approach with existing methods to demonstrate the advantage of our approach. PMID:25110737

Factors influencing indoor PM2.5 concentration in rural houses of northern China

NASA Astrophysics Data System (ADS)

Zhang, Xueyan; Chen, Bin

2018-02-01

In traditional houses in rural areas of Northern China, most traditional heating systems, heated by mini-stove in the kitchen, usually take agricultural residues as fuels resources. Besides, burning cave under the ground-floor of a rural house is also widely used. The higher PM2.5 concentration is crisis for human health. In this study, PM2.5 concentration, temperature, relative humidity inside and outside the houses have been measured, moreover the factors impact on I/O rate coefficient has been discussed. The results show that the I/O rate coefficient in the evening is 2.5 times greater than the I/O rate coefficient in the daytime. I/O rate coefficient of PM2.5 concentration is positive related to air temperature difference between indoor and outdoor. In addition, the impact of outdoor wind speed and predominant wind direction on the PM2.5 emission has been studied.

Approximate Sensory Data Collection: A Survey.

PubMed

Cheng, Siyao; Cai, Zhipeng; Li, Jianzhong

2017-03-10

With the rapid development of the Internet of Things (IoTs), wireless sensor networks (WSNs) and related techniques, the amount of sensory data manifests an explosive growth. In some applications of IoTs and WSNs, the size of sensory data has already exceeded several petabytes annually, which brings too many troubles and challenges for the data collection, which is a primary operation in IoTs and WSNs. Since the exact data collection is not affordable for many WSN and IoT systems due to the limitations on bandwidth and energy, many approximate data collection algorithms have been proposed in the last decade. This survey reviews the state of the art of approximatedatacollectionalgorithms. Weclassifythemintothreecategories: themodel-basedones, the compressive sensing based ones, and the query-driven ones. For each category of algorithms, the advantages and disadvantages are elaborated, some challenges and unsolved problems are pointed out, and the research prospects are forecasted.

Diskless supercomputers: Scalable, reliable I/O for the Tera-Op technology base

NASA Technical Reports Server (NTRS)

Katz, Randy H.; Ousterhout, John K.; Patterson, David A.

1993-01-01

Computing is seeing an unprecedented improvement in performance; over the last five years there has been an order-of-magnitude improvement in the speeds of workstation CPU's. At least another order of magnitude seems likely in the next five years, to machines with 500 MIPS or more. The goal of the ARPA Teraop program is to realize even larger, more powerful machines, executing as many as a trillion operations per second. Unfortunately, we have seen no comparable breakthroughs in I/O performance; the speeds of I/O devices and the hardware and software architectures for managing them have not changed substantially in many years. We have completed a program of research to demonstrate hardware and software I/O architectures capable of supporting the kinds of internetworked 'visualization' workstations and supercomputers that will appear in the mid 1990s. The project had three overall goals: high performance, high reliability, and scalable, multipurpose system.

Constructing topic models of Internet of Things for information processing.

PubMed

Xin, Jie; Cui, Zhiming; Zhang, Shukui; He, Tianxu; Li, Chunhua; Huang, Haojing

2014-01-01

Internet of Things (IoT) is regarded as a remarkable development of the modern information technology. There is abundant digital products data on the IoT, linking with multiple types of objects/entities. Those associated entities carry rich information and usually in the form of query records. Therefore, constructing high quality topic hierarchies that can capture the term distribution of each product record enables us to better understand users' search intent and benefits tasks such as taxonomy construction, recommendation systems, and other communications solutions for the future IoT. In this paper, we propose a novel record entity topic model (RETM) for IoT environment that is associated with a set of entities and records and a Gibbs sampling-based algorithm is proposed to learn the model. We conduct extensive experiments on real-world datasets and compare our approach with existing methods to demonstrate the advantage of our approach.

Effects of Intraosseous Tibial vs. Intravenous Vasopressin in a Hypovolemic Cardiac Arrest Model

PubMed Central

Fulkerson, Justin; Lowe, Robert; Anderson, Tristan; Moore, Heather; Craig, William; Johnson, Don

2016-01-01

Introduction This study compared the effects of vasopressin via tibial intraosseous (IO) and intravenous (IV) routes on maximum plasma concentration (Cmax), the time to maximum concentration (Tmax), return of spontaneous circulation (ROSC), and time to ROSC in a hypovolemic cardiac arrest model. Methods This study was a randomized prospective, between-subjects experimental design. A computer program randomly assigned 28 Yorkshire swine to one of four groups: IV (n=7), IO tibia (n=7), cardiopulmonary resuscitation (CPR) + defibrillation (n=7), and a control group that received just CPR (n=7). Ventricular fibrillation was induced, and subjects remained in arrest for two minutes. CPR was initiated and 40 units of vasopressin were administered via IO or IV routes. Blood samples were collected at 0.5, 1, 1.5, 2, 2.5, 3, and 4 minutes. CPR and defibrillation were initiated for 20 minutes or until ROSC was achieved. We measured vasopressin concentrations using high-performance liquid chromatography. Results There was no significant difference between the IO and IV groups relative to achieving ROSC (p=1.0) but a significant difference between the IV compared to the CPR+ defibrillation group (p=0.031) and IV compared to the CPR-only group (p=0.001). There was a significant difference between the IO group compared to the CPR+ defibrillation group (p=0.031) and IO compared to the CPR-only group (p=0.001). There was no significant difference between the CPR + defibrillation group and the CPR group (p=0.127). There was no significant difference in Cmax between the IO and IV groups (p=0.079). The mean ± standard deviation of Cmax of the IO group was 58,709±25, 463pg/mL compared to the IV group, which was 106,198±62, 135pg/mL. There was no significant difference in mean Tmax between the groups (p=0.084). There were no significant differences in odds of ROSC between the tibial IO and IV groups. Conclusion Prompt access to the vascular system using the IO route can circumvent the interruption in treatment observed with attempting conventional IV access. The IO route is an effective modality for the treatment of hypovolemic cardiac arrest and may be considered first line for rapid vascular access. PMID:26973756

Effects of Intraosseous Tibial vs. Intravenous Vasopressin in a Hypovolemic Cardiac Arrest Model.

PubMed

Fulkerson, Justin; Lowe, Robert; Anderson, Tristan; Moore, Heather; Craig, William; Johnson, Don

2016-03-01

This study compared the effects of vasopressin via tibial intraosseous (IO) and intravenous (IV) routes on maximum plasma concentration (Cmax), the time to maximum concentration (Tmax), return of spontaneous circulation (ROSC), and time to ROSC in a hypovolemic cardiac arrest model. This study was a randomized prospective, between-subjects experimental design. A computer program randomly assigned 28 Yorkshire swine to one of four groups: IV (n=7), IO tibia (n=7), cardiopulmonary resuscitation (CPR) + defibrillation (n=7), and a control group that received just CPR (n=7). Ventricular fibrillation was induced, and subjects remained in arrest for two minutes. CPR was initiated and 40 units of vasopressin were administered via IO or IV routes. Blood samples were collected at 0.5, 1, 1.5, 2, 2.5, 3, and 4 minutes. CPR and defibrillation were initiated for 20 minutes or until ROSC was achieved. We measured vasopressin concentrations using high-performance liquid chromatography. There was no significant difference between the IO and IV groups relative to achieving ROSC (p=1.0) but a significant difference between the IV compared to the CPR+ defibrillation group (p=0.031) and IV compared to the CPR-only group (p=0.001). There was a significant difference between the IO group compared to the CPR+ defibrillation group (p=0.031) and IO compared to the CPR-only group (p=0.001). There was no significant difference between the CPR + defibrillation group and the CPR group (p=0.127). There was no significant difference in Cmax between the IO and IV groups (p=0.079). The mean ± standard deviation of Cmax of the IO group was 58,709±25, 463 pg/mL compared to the IV group, which was 106,198±62, 135 pg/mL. There was no significant difference in mean Tmax between the groups (p=0.084). There were no significant differences in odds of ROSC between the tibial IO and IV groups. Prompt access to the vascular system using the IO route can circumvent the interruption in treatment observed with attempting conventional IV access. The IO route is an effective modality for the treatment of hypovolemic cardiac arrest and may be considered first line for rapid vascular access.

Wave vector modification of the infinite order sudden approximation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sachs, J.G.; Bowman, J.M.

1980-10-15

A simple method is proposed to modify the infinite order sudden approximation (IOS) in order to extend its region of quantitative validity. The method involves modifying the phase of the IOS scattering matrix to include a part calculated at the outgoing relative kinetic energy as well as a part calculated at the incoming kinetic energy. An immediate advantage of this modification is that the resulting S matrix is symmetric. We also present a closely related method in which the relative kinetic energies used in the calculation of the phase are determined from quasiclassical trajectory calculations. A set of trajectories ismore » run with the initial state being the incoming state, and another set is run with the initial state being the outgoing state, and the average final relative kinetic energy of each set is obtained. One part of the S-operator phase is then calculated at each of these kinetic energies. We apply these methods to vibrationally inelastic collinear collisions of an atom and a harmonic oscillator, and calculate transition probabilities P/sub n/1..-->..nf for three model systems. For systems which are sudden, or nearly so, the agreement with exact quantum close-coupling calculations is substantially improved over standard IOS ones when ..delta..n=such thatub f/-n/sub i/ is large, and the corresponding transition probability is small, i.e., less than 0.1. However, the modifications we propose will not improve the accuracy of the IOS transition probabilities for any collisional system unless the standard form of IOS already gives at least qualitative agreement with exact quantal calculations. We also suggest comparisons between some classical quantities and sudden predictions which should help in determining the validity of the sudden approximation. This is useful when exact quantal data is not available for comparison.« less

Design and Practical Evaluation of a Family of Lightweight Protocols for Heterogeneous Sensing through BLE Beacons in IoT Telemetry Applications.

PubMed

Hernández-Rojas, Dixys L; Fernández-Caramés, Tiago M; Fraga-Lamas, Paula; Escudero, Carlos J

2017-12-27

The Internet of Things (IoT) involves a wide variety of heterogeneous technologies and resource-constrained devices that interact with each other. Due to such constraints, IoT devices usually require lightweight protocols that optimize the use of resources and energy consumption. Among the different commercial IoT devices, Bluetooth and Bluetooth Low Energy (BLE)-based beacons, which broadcast periodically certain data packets to notify their presence, have experienced a remarkable growth, specially due to their application in indoor positioning systems. This article proposes a family of protocols named Lightweight Protocol for Sensors (LP4S) that provides fast responses and enables plug-and-play mechanisms that allow IoT telemetry systems to discover new nodes and to describe and auto-register the sensors and actuators connected to a beacon. Thus, three protocols are defined depending on the beacon hardware characteristics: LP4S-6 (for resource-constraint beacons), LP4S-X (for more powerful beacons) and LP4S-J (for beacons able to run complex firmware). In order to demonstrate the capabilities of the designed protocols, the most restrictive (LP4S-6) is tested after implementing it for a telemetry application in a beacon based on Eddystone (Google's open beacon format). Thus, the beacon specification is extended in order to increase its ability to manage unlimited sensors in a telemetry system without interfering in its normal operation with Eddystone frames. The performed experiments show the feasibility of the proposed solution and its superiority, in terms of latency and energy consumption, with respect to approaches based on Generic Attribute Profile (GATT) when multiple users connect to a mote or in scenarios where latency is not a restriction, but where low-energy consumption is essential.

Mobile Digital Recording: Adequacy of the iRig and iOS Device for Acoustic and Perceptual Analysis of Normal Voice.

PubMed

Oliveira, Gisele; Fava, Gaetano; Baglione, Melody; Pimpinella, Michael

2017-03-01

To determine whether the iRig and iOS device recording system is comparable with a standard computer recording system for digital voice recording. Thirty-seven vocally healthy adults, between ages 20 and 62, with a mean age of 33.9 years, 13 males and 24 females, were recruited. Recordings were simultaneously digitalized in an iPad and iPhone using a unidirectional condenser microphone for smartphones/tablets (iRig Mic, IK Multimedia) and in a computer laptop (Dell-Inspiron) using a unidirectional condenser microphone (Samson-CL5) connected to a preamplifier with phantom power. Both microphones were lined up at an equal fixed distance from the subject's mouth. Speech tasks consisted of a sustained vowel "ah" at comfortable pitch/loudness, counting from 1 to 10, and a glissando "ah" from a low to a high note. The samples captured on the iOS devices were transferred via SoundCloud in WAV format, and analyzed using the Praat software. The acoustic parameters measured were mean, min, and max F0, SD F0, jitter local, jitter rap, jitter ppq5, jitter ddp, shimmer local, shimmer local-dB, shimmer apq3, shimmer apq5, shimmer apq11, shimmer dda, NHR, and HNR. There were no statistically significant differences for any parameter and speech task analyzed for both iOS devices as compared with the gold standard computer/preamp system (all P values > 0.050). In addition, there were no statistical differences in the perceptual identification of the recordings among devices (P < 0.001). In the present study, the iRig and iOS device may provide reliable digital recording of normal voices. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Design and Practical Evaluation of a Family of Lightweight Protocols for Heterogeneous Sensing through BLE Beacons in IoT Telemetry Applications

PubMed Central

2017-01-01

The Internet of Things (IoT) involves a wide variety of heterogeneous technologies and resource-constrained devices that interact with each other. Due to such constraints, IoT devices usually require lightweight protocols that optimize the use of resources and energy consumption. Among the different commercial IoT devices, Bluetooth and Bluetooth Low Energy (BLE)-based beacons, which broadcast periodically certain data packets to notify their presence, have experienced a remarkable growth, specially due to their application in indoor positioning systems. This article proposes a family of protocols named Lightweight Protocol for Sensors (LP4S) that provides fast responses and enables plug-and-play mechanisms that allow IoT telemetry systems to discover new nodes and to describe and auto-register the sensors and actuators connected to a beacon. Thus, three protocols are defined depending on the beacon hardware characteristics: LP4S-6 (for resource-constraint beacons), LP4S-X (for more powerful beacons) and LP4S-J (for beacons able to run complex firmware). In order to demonstrate the capabilities of the designed protocols, the most restrictive (LP4S-6) is tested after implementing it for a telemetry application in a beacon based on Eddystone (Google’s open beacon format). Thus, the beacon specification is extended in order to increase its ability to manage unlimited sensors in a telemetry system without interfering in its normal operation with Eddystone frames. The performed experiments show the feasibility of the proposed solution and its superiority, in terms of latency and energy consumption, with respect to approaches based on Generic Attribute Profile (GATT) when multiple users connect to a mote or in scenarios where latency is not a restriction, but where low-energy consumption is essential. PMID:29280975

Wave vector modification of the infinite order sudden approximation

NASA Astrophysics Data System (ADS)

Sachs, Judith Grobe; Bowman, Joel M.

1980-10-01

A simple method is proposed to modify the infinite order sudden approximation (IOS) in order to extend its region of quantitative validity. The method involves modifying the phase of the IOS scattering matrix to include a part calculated at the outgoing relative kinetic energy as well as a part calculated at the incoming kinetic energy. An immediate advantage of this modification is that the resulting S matrix is symmetric. We also present a closely related method in which the relative kinetic energies used in the calculation of the phase are determined from quasiclassical trajectory calculations. A set of trajectories is run with the initial state being the incoming state, and another set is run with the initial state being the outgoing state, and the average final relative kinetic energy of each set is obtained. One part of the S-operator phase is then calculated at each of these kinetic energies. We apply these methods to vibrationally inelastic collinear collisions of an atom and a harmonic oscillator, and calculate transition probabilities Pn1→nf for three model systems. For systems which are sudden, or nearly so, the agreement with exact quantum close-coupling calculations is substantially improved over standard IOS ones when Δn=‖nf-ni‖ is large, and the corresponding transition probability is small, i.e., less than 0.1. However, the modifications we propose will not improve the accuracy of the IOS transition probabilities for any collisional system unless the standard form of IOS already gives at least qualitative agreement with exact quantal calculations. We also suggest comparisons between some classical quantities and sudden predictions which should help in determining the validity of the sudden approximation. This is useful when exact quantal data is not available for comparison.

An Extensible Sensing and Control Platform for Building Energy Management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rowe, Anthony; Berges, Mario; Martin, Christopher

2016-04-03

The goal of this project is to develop Mortar.io, an open-source BAS platform designed to simplify data collection, archiving, event scheduling and coordination of cross-system interactions. Mortar.io is optimized for (1) robustness to network outages, (2) ease of installation using plug-and-play and (3) scalable support for small to large buildings and campuses.

Fast I/O for Massively Parallel Applications

NASA Technical Reports Server (NTRS)

OKeefe, Matthew T.

1996-01-01

The two primary goals for this report were the design, contruction and modeling of parallel disk arrays for scientific visualization and animation, and a study of the IO requirements of highly parallel applications. In addition, further work in parallel display systems required to project and animate the very high-resolution frames resulting from our supercomputing simulations in ocean circulation and compressible gas dynamics.

Near-ultraviolet imaging of Jupiter's satellite Io with the Hubble Space Telescope

NASA Technical Reports Server (NTRS)

Paresce, F.; Sartoretti, P.; Albrecht, R.; Barbieri, C.; Blades, J. C.; Boksenberg, A.; Crane, P.; Deharveng, J. M.; Disney, M. J.; Jakobsen, P.

1992-01-01

The surface of Jupiter's Galilean satellite Io has been resolved for the first time in the near ultraviolet at 2850 A by the Faint Object Camera (FOC) on the Hubble Space Telescope (HST). The restored images reveal significant surface structure down to the resolution limit of the optical system corresponding to approximately 250 km at the sub-earth point.

Industry Strength Tool and Technology for Automated Synthesis of Safety-Critical Applications from Formal Specifications

DTIC Science & Technology

2015-11-01

28 2.3.4 Input/Output Automata ...various other modeling frameworks such as I/O Automata , Kahn Process Networks, Petri-nets, Multi-dimensional SDF, etc. are also used for designing...Formal Ideally suited to model DSP applications 3 Petri Nets Graphical Formal Used for modeling distributed systems 4 I/O Automata Both Formal

ARC-1979-A79-7074

NASA Image and Video Library

1979-07-04

P-21739 BW Range: 4.7 million kilometers (2.9 million miles) This picture of Io was taken as Voyager 2 closes in on the Jovian system. Scientists are studying these distant views of Io for evidences of changes since Voyager 1 observations in March of 79. Voyager 1 discovered that Io, the innermost of the Galilean satellites, is the most volcanically active body yet seen in the solar system, surpassing even earth. In this picture, the first volcano discovered by Voyager 1 is again visible in the lower left portion of the disk as a dark oval with a dark spot in the center. In March, this volcano appeared as a heart-shaped marking, not a symmetrical oval. Scientists believe that the non-symmetric markings earlier resulted from a constriction in the mouth of the volcanic vent causing erupting material to extrude preferentially in certain directions. Apparently, the volcanic eruptive activity, which sends material to altitudes of 280 kilometers (175 miles) or more above this volcano, has changed the vent geometry or dislodged an obstruction. Such changes in the form of eruptive fountains are common in terrestial volcanos, although on a much smaller scale than on Io.

A mobile mapping system for spatial information based on DGPS/EGIS

NASA Astrophysics Data System (ADS)

Pei, Ling; Wang, Qing; Gu, Juan

2007-11-01

With the rapid developments of mobile device and wireless communication, it brings a new challenge for acquiring the spatial information. A mobile mapping system based on differential global position system (DGPS) integrated with embedded geographic information system (EGIS) is designed. A mobile terminal adapts to various GPS differential environments such as single base mode and network GPS mode like Virtual Reference Station (VRS) and Master- Auxiliary Concept (MAC) by the mobile communication technology. The spatial information collected through DGPS is organized in an EGIS running in the embedded device. A set of mobile terminal in real-time DGPS based on GPRS adopting multithreading technique of serial port in manner of simulating overlapped I/O operating is developed, further more, the GPS message analysis and checkout based on Strategy Pattern for various receivers are included in the process of development. A mobile terminal accesses to the GPS network successfully by NTRIP (Networked Transport of RTCM via Internet Protocol) compliance. Finally, the accuracy and reliability of the mobile mapping system are proved by a lot of testing in 9 provinces all over the country.

Cassini UVIS Observations of the Io Plasma Torus. 3; Observations of Temporal and Azimuthal Variability

NASA Technical Reports Server (NTRS)

Steffl, A. J.; Delamere, P. A.; Bagenal, F.

2006-01-01

In this third paper in a series presenting observations by the Cassini Ultraviolet Imaging Spectrometer (UVIS) of the Io plasma torus, we show remarkable, though subtle, spatio-temporal variations in torus properties. The Io torus is found to exhibit significant, near sinusoidal variations in ion composition as a functions of azimuthal position. The azimuthal variation in composition is such that the mixing ratio of S II us strongly correlated with the mixing ratio of S III and the equatorial electron density and strongly anti-correlated with the mixing ratios of both S IV and O II and the equatorial electron temperature. Surprisingly, the azimuthal variation in ion composition is observed to have a period of 10.07 h -- 1.5% longer than the System III rotation period of Jupiter, yet 1.3% shorter than the System UV period defined by [Brown, M. E., 1995. J. Geophys. Res. 100, 21683-21696]. Although the amplitude of the azimuthal variation of S III and O II remained in the range of 2-5%, the amplitude of the S II and S IV compositional variation ranged between 5 and 25% during the UVIS observations. Furthermore, the amplitude of the azimuthal variations of S II and S IV appears to be modulated by its location in System III longitude, such that when the region of maximum S II mixing ration (minimum S IV mixing ratio) is aligned with a System III longitude of 200 deg +/-, the amplitude is a factor of 4 greater than when the variation is anti-aligned. This behavior can explain numerous, often apparently contradictory, observations of variations in the properties of the Io plasma torus with the System III and System IV coordinate systems.

Indian Ocean research: Opportunities and challenges

NASA Astrophysics Data System (ADS)

Hood, Raleigh R.; Wiggert, Jerry D.; Naqvi, S. Wajih A.

Historically, the Indian Ocean (IO) has received relatively little attention from the oceanographic community and therefore remains substantially undersampled compared to the Atlantic and Pacific oceans. This situation is compounded by the IO being a dynamically complex and highly variable system under monsoonal influence. The biogeochemical and ecological impacts of this complex physical forcing are not yet fully understood. Specific questions and hypotheses have emerged from recent studies that have yet to be tested, such as the potential role of zooplankton grazing versus iron limitation in controlling phytoplankton production in the Arabian Sea (AS). Furthermore, the IO is a globally important denitrification zone, and it also appears to be a region where N2 fixation rates are significant. However, there are still large uncertainties in the rate estimates for both. The IO is also warming rapidly, but the impacts of this warming on the biota, carbon uptake, and nitrogen cycling are unquantified. The increasing population density and rapid economic growth of the countries surrounding the Bay of Bengal and eastern AS make these regions' coastal environments particularly vulnerable to anthropogenic influences. Warming and anthropogenic effects might also impact the huge myctophid stocks in the AS and other commercially valuable species. These potential influences and their socioeconomic ramifications need to be explored. Deployment of coastal and open ocean observing systems in the IO has created new opportunities for carrying out biogeochemical and ecological research. International research efforts should be motivated to exploit these opportunities for addressing the questions identified in this chapter.

Least mean square fourth based microgrid state estimation algorithm using the internet of things technology.

PubMed

Rana, Md Masud

2017-01-01

This paper proposes an innovative internet of things (IoT) based communication framework for monitoring microgrid under the condition of packet dropouts in measurements. First of all, the microgrid incorporating the renewable distributed energy resources is represented by a state-space model. The IoT embedded wireless sensor network is adopted to sense the system states. Afterwards, the information is transmitted to the energy management system using the communication network. Finally, the least mean square fourth algorithm is explored for estimating the system states. The effectiveness of the developed approach is verified through numerical simulations.

An Efficient User Authentication and User Anonymity Scheme with Provably Security for IoT-Based Medical Care System.

PubMed

Li, Chun-Ta; Wu, Tsu-Yang; Chen, Chin-Ling; Lee, Cheng-Chi; Chen, Chien-Ming

2017-06-23

In recent years, with the increase in degenerative diseases and the aging population in advanced countries, demands for medical care of older or solitary people have increased continually in hospitals and healthcare institutions. Applying wireless sensor networks for the IoT-based telemedicine system enables doctors, caregivers or families to monitor patients' physiological conditions at anytime and anyplace according to the acquired information. However, transmitting physiological data through the Internet concerns the personal privacy of patients. Therefore, before users can access medical care services in IoT-based medical care system, they must be authenticated. Typically, user authentication and data encryption are most critical for securing network communications over a public channel between two or more participants. In 2016, Liu and Chung proposed a bilinear pairing-based password authentication scheme for wireless healthcare sensor networks. They claimed their authentication scheme cannot only secure sensor data transmission, but also resist various well-known security attacks. In this paper, we demonstrate that Liu-Chung's scheme has some security weaknesses, and we further present an improved secure authentication and data encryption scheme for the IoT-based medical care system, which can provide user anonymity and prevent the security threats of replay and password/sensed data disclosure attacks. Moreover, we modify the authentication process to reduce redundancy in protocol design, and the proposed scheme is more efficient in performance compared with previous related schemes. Finally, the proposed scheme is provably secure in the random oracle model under ECDHP.

Updated modeling of Io and non-Io Radio Auroral Emissions of Jupiter

NASA Astrophysics Data System (ADS)

Louis, C.; Lamy, L.; Zarka, P.; Cecconi, B.; Hess, S.

2015-10-01

The radio auroral emissions produced by the Jupiter's magnetosphere between a few kHz and 40MHz, the most intense of our Solar System, are known since half a century, but they still drive many questions, and their deepened study is one of the main aim of the JUNO missions (arrival in July 2016). Jovian auroral radio emissions are thought to be produced through the Cyclotron Maser Instability (CMI), from non-maxwellian weakly relativistic electrons gyrating along high-latitude magnetic fields lines (Zarka, 1998). These emissions divide in different spectral components, driven or not by the moon Io. The origin and the relationship between kilometric, hectometric and decametric non-Io emissions in particular remains poorly understood. To investigate these emissions, we simulated numerical dynamic spectra with the most recent version of the ExPRES code - Exoplanetary and Planetary Radio Emission Simulator, available at http://maser.obspm.fr - already used to successfully model Io decametric and Saturn's kilometric arcshaped emissions (Hess et al., 2008, Lamy et al., 2008) and predict exoplanetary radio emissions (Hess et al., 2011). Such simulations bring direct constraints on the locus of active magnetic field lines and on the nature of CMI-unstable electrons (Hess et al., submitted). We validated the new theoretical calculation of the beaming angle used by ExPRES, which now includes refraction at the source. We then built updated simulations of Io and non-Io emissions which were compared to the radio observations acquired by the Cassini spacecraft (Jupiter flyby in 2000) and the Nançay decameter array (routines observations of Jupiter).

'Social, innovative and smart cities are happy and resilient': insights from the WHO EURO 2014 International Healthy Cities Conference.

PubMed

Kamel Boulos, Maged N; Tsouros, Agis D; Holopainen, Arto

2015-01-14

This paper provides a brief overview of, and elaborates on, some of the presentations, discussions and conclusions from Day 4 of the 'WHO EURO 2014 International Healthy Cities Conference: Health and the City - Urban Living in the 21st Century', held in Athens, Greece on 25 October 2014. The Internet of Things (IoT) is made of sensors and other components that connect our version of the world made of atoms, i.e., humans/our bodies, our devices, vehicles, roads, buildings, plants, animals, etc., with a mirror digital version made of bits. This enables cities and regions to be self-aware and dynamically reconfigurable in real- or near-real-time, based on changes that are continuously monitored and captured by sensors, similar to the way the internal biological systems of a living being operate and respond to their environment (homeostasis). Data collected by various IoT sensors and processed via appropriate analytics can also help predict the immediate future with reasonable accuracy, which enables better planned responses and mitigation actions. Cities and regions can thus become more adaptable and resilient in face of adversity. Furthermore, IoT can link atoms (humans) to other atoms (humans) (again via bits), resulting in the formation of 'smart(er) communities' that are socially connected in new ways and potentially happier. Cities, but also less urbanised regions and the countryside, could all benefit from, and harness the power of, IoT to improve the health, well-being and overall quality of life of the local populations, actively engage citizens in a smarter governance of their region, empower them to better care for one another, promote stronger social inclusion, and ensure a greener, sustainable and more enjoyable environment for all. Technology can also help reverse the 'brain drain' from the countryside and smaller towns to larger metropolises by making the former more attractive and connected, with better services akin to those found in larger cities. The article also discusses some ways of measuring and benchmarking the performance of smart cities and their impact on well-being. However, it should be emphasised that technology is not a panacea and that other factors are equally important in creating happier and healthier cities and regions.

Skel: Generative Software for Producing Skeletal I/O Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, J.; Klasky, S.; Lofstead, J.

2011-01-01

Massively parallel computations consist of a mixture of computation, communication, and I/O. As part of the co-design for the inevitable progress towards exascale computing, we must apply lessons learned from past work to succeed in this new age of computing. Of the three components listed above, implementing an effective parallel I/O solution has often been overlooked by application scientists and was usually added to large scale simulations only when existing serial techniques had failed. As scientists teams scaled their codes to run on hundreds of processors, it was common to call on an I/O expert to implement a set ofmore » more scalable I/O routines. These routines were easily separated from the calculations and communication, and in many cases, an I/O kernel was derived from the application which could be used for testing I/O performance independent of the application. These I/O kernels developed a life of their own used as a broad measure for comparing different I/O techniques. Unfortunately, as years passed and computation and communication changes required changes to the I/O, the separate I/O kernel used for benchmarking remained static no longer providing an accurate indicator of the I/O performance of the simulation making I/O research less relevant for the application scientists. In this paper we describe a new approach to this problem where I/O kernels are replaced with skeletal I/O applications automatically generated from an abstract set of simulation I/O parameters. We realize this abstraction by leveraging the ADIOS middleware's XML I/O specification with additional runtime parameters. Skeletal applications offer all of the benefits of I/O kernels including allowing I/O optimizations to focus on useful I/O patterns. Moreover, since they are automatically generated, it is easy to produce an updated I/O skeleton whenever the simulation's I/O changes. In this paper we analyze the performance of automatically generated I/O skeletal applications for the S3D and GTS codes. We show that these skeletal applications achieve performance comparable to that of the production applications. We wrap up the paper with a discussion of future changes to make the skeletal application better approximate the actual I/O performed in the simulation.« less

A Methodological Approach for Assessing Amplified Reflection Distributed Denial of Service on the Internet of Things

PubMed Central

Costa Gondim, João José; de Oliveira Albuquerque, Robson; Clayton Alves Nascimento, Anderson; García Villalba, Luis Javier; Kim, Tai-Hoon

2016-01-01

Concerns about security on Internet of Things (IoT) cover data privacy and integrity, access control, and availability. IoT abuse in distributed denial of service attacks is a major issue, as typical IoT devices’ limited computing, communications, and power resources are prioritized in implementing functionality rather than security features. Incidents involving attacks have been reported, but without clear characterization and evaluation of threats and impacts. The main purpose of this work is to methodically assess the possible impacts of a specific class–amplified reflection distributed denial of service attacks (AR-DDoS)–against IoT. The novel approach used to empirically examine the threat represented by running the attack over a controlled environment, with IoT devices, considered the perspective of an attacker. The methodology used in tests includes that perspective, and actively prospects vulnerabilities in computer systems. This methodology defines standardized procedures for tool-independent vulnerability assessment based on strategy, and the decision flows during execution of penetration tests (pentests). After validation in different scenarios, the methodology was applied in amplified reflection distributed denial of service (AR-DDoS) attack threat assessment. Results show that, according to attack intensity, AR-DDoS saturates reflector infrastructure. Therefore, concerns about AR-DDoS are founded, but expected impact on abused IoT infrastructure and devices will be possibly as hard as on final victims. PMID:27827931

Enabling Secure XMPP Communications in Federated IoT Clouds Through XEP 0027 and SAML/SASL SSO

PubMed Central

Celesti, Antonio; Fazio, Maria; Villari, Massimo

2017-01-01

Nowadays, in the panorama of Internet of Things (IoT), finding a right compromise between interactivity and security is not trivial at all. Currently, most of pervasive communication technologies are designed to work locally. As a consequence, the development of large-scale Internet services and applications is not so easy for IoT Cloud providers. The main issue is that both IoT architectures and services have started as simple but they are becoming more and more complex. Consequently, the web service technology is often inappropriate. Recently, many operators in both academia and industry fields are considering the possibility to adopt the eXtensible Messaging and Presence Protocol (XMPP) for the implementation of IoT Cloud communication systems. In fact, XMPP offers many advantages in term of real-time capabilities, efficient data distribution, service discovery and inter-domain communication compared to other technologies. Nevertheless, the protocol lacks of native security, data confidentiality and trustworthy federation features. In this paper, considering an XMPP-based IoT Cloud architectural model, we discuss how can be possible to enforce message signing/encryption and Single-Sign On (SSO) authentication respectively for secure inter-module and inter-domain communications in a federated environment. Experiments prove that security mechanisms introduce an acceptable overhead, considering the obvious advantages achieved in terms of data trustiness and privacy. PMID:28178214

Building IoT Services for Aging in Place Using Standard-Based IoT Platforms and Heterogeneous IoT Products.

PubMed

Fattah, Sheik Mohammad Mostakim; Sung, Nak-Myoung; Ahn, Il-Yeup; Ryu, Minwoo; Yun, Jaeseok

2017-10-11

An aging population and human longevity is a global trend. Many developed countries are struggling with the yearly increasing healthcare cost that dominantly affects their economy. At the same time, people living with old adults suffering from a progressive brain disorder such as Alzheimer's disease are enduring even more stress and depression than those patients while caring for them. Accordingly, seniors' ability to live independently and comfortably in their current home for as long as possible has been crucial to reduce the societal cost for caregiving and thus give family members peace of mind, called 'aging in place' (AIP). In this paper we present a way of building AIP services using standard-based IoT platforms and heterogeneous IoT products. An AIP service platform is designed and created by combining previous standard-based IoT platforms in a collaborative way. A service composition tool is also created that allows people to create AIP services in an efficient way. To show practical usability of our proposed system, we choose a service scenario for medication compliance and implement a prototype service which could give old adults medication reminder appropriately at the right time (i.e., when it is time to need to take pills) through light and speaker at home but also wrist band and smartphone even outside the home.

Enabling Secure XMPP Communications in Federated IoT Clouds Through XEP 0027 and SAML/SASL SSO.

PubMed

Celesti, Antonio; Fazio, Maria; Villari, Massimo

2017-02-07

Nowadays, in the panorama of Internet of Things (IoT), finding a right compromise between interactivity and security is not trivial at all. Currently, most of pervasive communication technologies are designed to work locally. As a consequence, the development of large-scale Internet services and applications is not so easy for IoT Cloud providers. The main issue is that both IoT architectures and services have started as simple but they are becoming more and more complex. Consequently, the web service technology is often inappropriate. Recently, many operators in both academia and industry fields are considering the possibility to adopt the eXtensible Messaging and Presence Protocol (XMPP) for the implementation of IoT Cloud communication systems. In fact, XMPP offers many advantages in term of real-time capabilities, efficient data distribution, service discovery and inter-domain communication compared to other technologies. Nevertheless, the protocol lacks of native security, data confidentiality and trustworthy federation features. In this paper, considering an XMPP-based IoT Cloud architectural model, we discuss how can be possible to enforce message signing/encryption and Single-Sign On (SSO) authentication respectively for secure inter-module and inter-domain communications in a federated environment. Experiments prove that security mechanisms introduce an acceptable overhead, considering the obvious advantages achieved in terms of data trustiness and privacy.

A Methodological Approach for Assessing Amplified Reflection Distributed Denial of Service on the Internet of Things.

PubMed

Costa Gondim, João José; de Oliveira Albuquerque, Robson; Clayton Alves Nascimento, Anderson; García Villalba, Luis Javier; Kim, Tai-Hoon

2016-11-04

Concerns about security on Internet of Things (IoT) cover data privacy and integrity, access control, and availability. IoT abuse in distributed denial of service attacks is a major issue, as typical IoT devices' limited computing, communications, and power resources are prioritized in implementing functionality rather than security features. Incidents involving attacks have been reported, but without clear characterization and evaluation of threats and impacts. The main purpose of this work is to methodically assess the possible impacts of a specific class-amplified reflection distributed denial of service attacks (AR-DDoS)-against IoT. The novel approach used to empirically examine the threat represented by running the attack over a controlled environment, with IoT devices, considered the perspective of an attacker. The methodology used in tests includes that perspective, and actively prospects vulnerabilities in computer systems. This methodology defines standardized procedures for tool-independent vulnerability assessment based on strategy, and the decision flows during execution of penetration tests (pentests). After validation in different scenarios, the methodology was applied in amplified reflection distributed denial of service (AR-DDoS) attack threat assessment. Results show that, according to attack intensity, AR-DDoS saturates reflector infrastructure. Therefore, concerns about AR-DDoS are founded, but expected impact on abused IoT infrastructure and devices will be possibly as hard as on final victims.

An approach to enhance pnetCDF performance in ...

EPA Pesticide Factsheets

Data intensive simulations are often limited by their I/O (input/output) performance, and "novel" techniques need to be developed in order to overcome this limitation. The software package pnetCDF (parallel network Common Data Form), which works with parallel file systems, was developed to address this issue by providing parallel I/O capability. This study examines the performance of an application-level data aggregation approach which performs data aggregation along either row or column dimension of MPI (Message Passing Interface) processes on a spatially decomposed domain, and then applies the pnetCDF parallel I/O paradigm. The test was done with three different domain sizes which represent small, moderately large, and large data domains, using a small-scale Community Multiscale Air Quality model (CMAQ) mock-up code. The examination includes comparing I/O performance with traditional serial I/O technique, straight application of pnetCDF, and the data aggregation along row and column dimension before applying pnetCDF. After the comparison, "optimal" I/O configurations of this application-level data aggregation approach were quantified. Data aggregation along the row dimension (pnetCDFcr) works better than along the column dimension (pnetCDFcc) although it may perform slightly worse than the straight pnetCDF method with a small number of processors. When the number of processors becomes larger, pnetCDFcr outperforms pnetCDF significantly. If the number of proces

Building IoT Services for Aging in Place Using Standard-Based IoT Platforms and Heterogeneous IoT Products

PubMed Central

Fattah, Sheik Mohammad Mostakim; Sung, Nak-Myoung; Ahn, Il-Yeup; Ryu, Minwoo; Yun, Jaeseok

2017-01-01

An aging population and human longevity is a global trend. Many developed countries are struggling with the yearly increasing healthcare cost that dominantly affects their economy. At the same time, people living with old adults suffering from a progressive brain disorder such as Alzheimer’s disease are enduring even more stress and depression than those patients while caring for them. Accordingly, seniors’ ability to live independently and comfortably in their current home for as long as possible has been crucial to reduce the societal cost for caregiving and thus give family members peace of mind, called ‘aging in place’ (AIP). In this paper we present a way of building AIP services using standard-based IoT platforms and heterogeneous IoT products. An AIP service platform is designed and created by combining previous standard-based IoT platforms in a collaborative way. A service composition tool is also created that allows people to create AIP services in an efficient way. To show practical usability of our proposed system, we choose a service scenario for medication compliance and implement a prototype service which could give old adults medication reminder appropriately at the right time (i.e., when it is time to need to take pills) through light and speaker at home but also wrist band and smartphone even outside the home. PMID:29019964

Real-tiem Adaptive Control Scheme for Superior Plasma Confinement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander Trunov, Ph.D.

2001-06-01

During this Phase I project, IOS, in collaboration with our subcontractors at General Atomics, Inc., acquired and analyzed measurement data on various plasma equilibrium modes. We developed a Matlab-based toolbox consisting of linear and neural network approximators that are capable of learning and predicting, with accuracy, the behavior of plasma parameters. We also began development of the control algorithm capable of using the model of the plasma obtained by the neural network approximator.

PCI-based WILDFIRE reconfigurable computing engines

NASA Astrophysics Data System (ADS)

Fross, Bradley K.; Donaldson, Robert L.; Palmer, Douglas J.

1996-10-01

WILDFORCE is the first PCI-based custom reconfigurable computer that is based on the Splash 2 technology transferred from the National Security Agency and the Institute for Defense Analyses, Supercomputing Research Center (SRC). The WILDFORCE architecture has many of the features of the WILDFIRE computer, such as field- programmable gate array (FPGA) based processing elements, linear array and crossbar interconnection, and high- performance memory and I/O subsystems. New features introduced in the PCI-based WILDFIRE systems include memory/processor options that can be added to any processing element. These options include static and dynamic memory, digital signal processors (DSPs), FPGAs, and microprocessors. In addition to memory/processor options, many different application specific connectors can be used to extend the I/O capabilities of the system, including systolic I/O, camera input and video display output. This paper also discusses how this new PCI-based reconfigurable computing engine is used for rapid-prototyping, real-time video processing and other DSP applications.

On possible life on Jupiter's satellite Io

NASA Astrophysics Data System (ADS)

Vidmachenko, A. P.

2018-05-01

Some of the satellites of Jupiter may well be suitable both for mastering, and for finding possible traces of life there. Among them such satellite like Io - nearest Galilean satellite of Jupiter, and one of the most volcanically active bodies in the solar system. Warming of the mantle is caused by a powerful tidal force from the side of Jupiter. This leads to the heating of some parts of the mantle to a temperature above 1800 K, with an average surface temperature of about 140 K. But under its surface can be safe and even comfortable shelters, where life could once have come from the outside (even in a very primitive form), and could survive to this day. Moreover, according to some model's assumptions, Io could sometime be formed in another part of the Solar system, where the water could exist. Note that on neighboring Galilean satellites now exist significant amounts of water .

RGCA: A Reliable GPU Cluster Architecture for Large-Scale Internet of Things Computing Based on Effective Performance-Energy Optimization

PubMed Central

Chen, Qingkui; Zhao, Deyu; Wang, Jingjuan

2017-01-01

This paper aims to develop a low-cost, high-performance and high-reliability computing system to process large-scale data using common data mining algorithms in the Internet of Things (IoT) computing environment. Considering the characteristics of IoT data processing, similar to mainstream high performance computing, we use a GPU (Graphics Processing Unit) cluster to achieve better IoT services. Firstly, we present an energy consumption calculation method (ECCM) based on WSNs. Then, using the CUDA (Compute Unified Device Architecture) Programming model, we propose a Two-level Parallel Optimization Model (TLPOM) which exploits reasonable resource planning and common compiler optimization techniques to obtain the best blocks and threads configuration considering the resource constraints of each node. The key to this part is dynamic coupling Thread-Level Parallelism (TLP) and Instruction-Level Parallelism (ILP) to improve the performance of the algorithms without additional energy consumption. Finally, combining the ECCM and the TLPOM, we use the Reliable GPU Cluster Architecture (RGCA) to obtain a high-reliability computing system considering the nodes’ diversity, algorithm characteristics, etc. The results show that the performance of the algorithms significantly increased by 34.1%, 33.96% and 24.07% for Fermi, Kepler and Maxwell on average with TLPOM and the RGCA ensures that our IoT computing system provides low-cost and high-reliability services. PMID:28777325

Design of external sensors board based on Bluetooth interface of smart phones for structural health monitoring system

NASA Astrophysics Data System (ADS)

Yu, Yan; Zhou, Yaping; Zhao, Xuefeng; Li, Dongsheng; Ou, Jinping

2016-04-01

As an important part of new information technology, the Internet of Things(IoT) is based on intelligent perception, recognition technology, ubiquitous computing, ubiquitous network integration, and it is known as the third wave of the development of information industry in the world after the computer and the Internet. And Smart Phones are the general term for a class of mobile phones with a separate operating system and operational memory, in which the third-party service programs including software, games, navigation, et.al, can be installed. Smart Phones, with not only sensors but also actuators, are widely used in the IoT world. As the current hot issues in the engineering area, Structural health monitoring (SHM) is also facing new problems about design ideas in the IoT environment. The development of IoT, wireless sensor network and mobile communication technology, provides a good technical platform for SHM. Based on these facts, this paper introduces a kind of new idea for Structural Health Monitoring using Smart Phones Technique. The system is described in detail, and the external sensor board based on Bluetooth interface is designed, the test based on Smart Phones is finished to validate the implementation and feasibility. The research is preliminary and more tests need to be carried out before it can be of practical use.

RGCA: A Reliable GPU Cluster Architecture for Large-Scale Internet of Things Computing Based on Effective Performance-Energy Optimization.

PubMed

Fang, Yuling; Chen, Qingkui; Xiong, Neal N; Zhao, Deyu; Wang, Jingjuan

2017-08-04

This paper aims to develop a low-cost, high-performance and high-reliability computing system to process large-scale data using common data mining algorithms in the Internet of Things (IoT) computing environment. Considering the characteristics of IoT data processing, similar to mainstream high performance computing, we use a GPU (Graphics Processing Unit) cluster to achieve better IoT services. Firstly, we present an energy consumption calculation method (ECCM) based on WSNs. Then, using the CUDA (Compute Unified Device Architecture) Programming model, we propose a Two-level Parallel Optimization Model (TLPOM) which exploits reasonable resource planning and common compiler optimization techniques to obtain the best blocks and threads configuration considering the resource constraints of each node. The key to this part is dynamic coupling Thread-Level Parallelism (TLP) and Instruction-Level Parallelism (ILP) to improve the performance of the algorithms without additional energy consumption. Finally, combining the ECCM and the TLPOM, we use the Reliable GPU Cluster Architecture (RGCA) to obtain a high-reliability computing system considering the nodes' diversity, algorithm characteristics, etc. The results show that the performance of the algorithms significantly increased by 34.1%, 33.96% and 24.07% for Fermi, Kepler and Maxwell on average with TLPOM and the RGCA ensures that our IoT computing system provides low-cost and high-reliability services.

Final Report for File System Support for Burst Buffers on HPC Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, W.; Mohror, K.

Distributed burst buffers are a promising storage architecture for handling I/O workloads for exascale computing. As they are being deployed on more supercomputers, a file system that efficiently manages these burst buffers for fast I/O operations carries great consequence. Over the past year, FSU team has undertaken several efforts to design, prototype and evaluate distributed file systems for burst buffers on HPC systems. These include MetaKV: a Key-Value Store for Metadata Management of Distributed Burst Buffers, a user-level file system with multiple backends, and a specialized file system for large datasets of deep neural networks. Our progress for these respectivemore » efforts are elaborated further in this report.« less

An Advanced IoT-based System for Intelligent Energy Management in Buildings.

PubMed

Marinakis, Vangelis; Doukas, Haris

2018-02-16

The energy sector is closely interconnected with the building sector and integrated Information and Communication Technologies (ICT) solutions for effective energy management supporting decision-making at building, district and city level are key fundamental elements for making a city Smart. The available systems are designed and intended exclusively for a predefined number of cases and systems without allowing for expansion and interoperability with other applications that is partially due to the lack of semantics. This paper presents an advanced Internet of Things (IoT) based system for intelligent energy management in buildings. A semantic framework is introduced aiming at the unified and standardised modelling of the entities that constitute the building environment. Suitable rules are formed, aiming at the intelligent energy management and the general modus operandi of Smart Building. In this context, an IoT-based system was implemented, which enhances the interactivity of the buildings' energy management systems. The results from its pilot application are presented and discussed. The proposed system extends existing approaches and integrates cross-domain data, such as the building's data (e.g., energy management systems), energy production, energy prices, weather data and end-users' behaviour, in order to produce daily and weekly action plans for the energy end-users with actionable personalised information.

An Advanced IoT-based System for Intelligent Energy Management in Buildings

PubMed Central

Doukas, Haris

2018-01-01

The energy sector is closely interconnected with the building sector and integrated Information and Communication Technologies (ICT) solutions for effective energy management supporting decision-making at building, district and city level are key fundamental elements for making a city Smart. The available systems are designed and intended exclusively for a predefined number of cases and systems without allowing for expansion and interoperability with other applications that is partially due to the lack of semantics. This paper presents an advanced Internet of Things (IoT) based system for intelligent energy management in buildings. A semantic framework is introduced aiming at the unified and standardised modelling of the entities that constitute the building environment. Suitable rules are formed, aiming at the intelligent energy management and the general modus operandi of Smart Building. In this context, an IoT-based system was implemented, which enhances the interactivity of the buildings’ energy management systems. The results from its pilot application are presented and discussed. The proposed system extends existing approaches and integrates cross-domain data, such as the building’s data (e.g., energy management systems), energy production, energy prices, weather data and end-users’ behaviour, in order to produce daily and weekly action plans for the energy end-users with actionable personalised information. PMID:29462957

Relating small airways to asthma control by using impulse oscillometry in children.

PubMed

Shi, Yixin; Aledia, Anna S; Tatavoosian, Ahramahzd V; Vijayalakshmi, Shruthi; Galant, Stanley P; George, Steven C

2012-03-01

Previous reports suggest that the peripheral airways are associated with asthma control. Patient history, although subjective, is used largely to assess asthma control in children because spirometric results are many times normal values. Impulse oscillometry (IOS) is an objective and noninvasive measurement of lung function that has the potential to examine independently both small- and large-airway obstruction. We sought to determine the utility of IOS in assessing asthma control in children. Asthmatic and healthy children (6-17 years) were enrolled in the study. Spirometric and IOS (resistance of the respiratory system at 5 Hz [R5] and 20 Hz [R20], reactance of the respiratory system at 5 Hz [X5], resonant frequency of reactance [Fres], and area under the reactance curve between 5 Hz and Fres [reactance area {AX}]) values were collected in triplicate before and after a bronchodilator was administered. The physicians were blinded to the IOS measurements and assessed asthma control using American Thoracic Society guidelines. Small-airway IOS measurements, including the difference of R5 and R20 [R5-20], X5, Fres, and AX, of children with uncontrolled asthma (n = 44) were significantly different from those of children with controlled asthma (n = 57) and healthy children (n = 14), especially before the administration of a bronchodilator. However, there was no difference in large-airway IOS values (R20). No differences were found between children with controlled asthma and healthy children in any of the end points. Receiver operating characteristic analysis showed cut points for baseline R5-20 (1.5 cm H(2)O · L(-1) · s) and AX (9.5 cm H(2)O · L(-1)) that effectively discriminated controlled versus uncontrolled asthma (area under the curve, 0.86 and 0.84) and correctly classified more than 80% of the population. Uncontrolled asthma is associated with small-airways dysfunction, and IOS might be a reliable and noninvasive method to assess asthma control in children. Copyright © 2011 American Academy of Allergy, Asthma & Immunology. Published by Mosby, Inc. All rights reserved.

Spatiotemporal access model based on reputation for the sensing layer of the IoT.

PubMed

Guo, Yunchuan; Yin, Lihua; Li, Chao; Qian, Junyan

2014-01-01

Access control is a key technology in providing security in the Internet of Things (IoT). The mainstream security approach proposed for the sensing layer of the IoT concentrates only on authentication while ignoring the more general models. Unreliable communications and resource constraints make the traditional access control techniques barely meet the requirements of the sensing layer of the IoT. In this paper, we propose a model that combines space and time with reputation to control access to the information within the sensing layer of the IoT. This model is called spatiotemporal access control based on reputation (STRAC). STRAC uses a lattice-based approach to decrease the size of policy bases. To solve the problem caused by unreliable communications, we propose both nondeterministic authorizations and stochastic authorizations. To more precisely manage the reputation of nodes, we propose two new mechanisms to update the reputation of nodes. These new approaches are the authority-based update mechanism (AUM) and the election-based update mechanism (EUM). We show how the model checker UPPAAL can be used to analyze the spatiotemporal access control model of an application. Finally, we also implement a prototype system to demonstrate the efficiency of our model.

K2 Au(IO3)5 and β-KAu(IO3)4: Polar Materials with Strong SHG Responses Originating from Synergistic Effect of AuO4 and IO3 Units.

PubMed

Xu, Xiang; Hu, Chun-Li; Li, Bing-Xuan; Mao, Jiang-Gao

2016-01-26

Two new polar potassium gold iodates, namely, K2 Au(IO3)5 (Cmc21) and β-KAu(IO3)4 (C2), have been synthesized and structurally characterized. Both compounds feature zero-dimensional polar [Au(IO3)4](-) units composed of an AuO4 square-planar unit coordinated by four IO3(-) ions in a monodentate fashion. In β-KAu(IO3)4, isolated [Au(IO3)4](-) ions are separated by K(+) ions, whereas in K2 Au(IO3)5, isolated [Au(IO3)4](-) ions and non-coordinated IO3(-) units are separated by K(+) ions. Both compounds are thermally stable up to 400 °C and exhibit high transmittance in the NIR region (λ=800-2500 nm) with measured optical band gaps of 2.65 eV for K2 Au(IO3 )5 and 2.75 eV for β-KAu(IO3)4. Powder second-harmonic generation measurements by using λ=2.05 μm laser radiation indicate that K2 Au(IO3)5 and β-KAu(IO3)4 are both phase-matchable materials with strong SHG responses of approximately 1.0 and 1.3 times that of KTiOPO4, respectively. Theoretical calculations based on DFT methods confirm that such strong SHG responses originate from a synergistic effect of the AuO4 and IO3 units. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ada Compiler Validation Summary Report: Certificate Number: 920509S1. 11259 Alenia Aeritalia and Selenia S.p.A DACS VAX/VMS to 80x86 PM MARA Ada Cross Compiler, Version 4.6 Microvax 4000/200 = MARA

DTIC Science & Technology

1992-01-01

area end basic io types; 11.3.3 TEXT 10 -- Date 31 October 1983 -- Programmer Soeren Prehn (, Knud Joergen Kirkegaard) -- Project Portable Ada...Programmer Peter Haff (, Soeren Prehn , Knud Joergen Kirkegaard) -- Project Portable Ada Programming System -- Module SEQIOS.ADA -- Description...Peter Haff (,Soeren Prehn , Knud Joergen Kirkegaard) -- Project Portable Ada Programming System -- Module DIR IO.ADA -- Description Specification of

Simplified Input for Certain Aerodynamic Nose Configurations to the Grumman Quick-Geometry System (A KWIKNOSE User’s Manual)

DTIC Science & Technology

1978-02-01

very little effort, the author has constructed a cathode ray tube (CRT) plotting program using the QUICKLOK portion of QUICK and has found it...eZMAPAX(IO)~ASIO(iO)*ZSI8(IO)* S R L B ( 8 ) " CONHON /IA/ICASE(IO)tJCASE(30)* NCAS [(7)*NR(3)*NS(3),NB(8) • COMMON /RS/KItMItKJ*MJ*NIJ;LINE*BLNK*R|NF...6289632o0149138~1609162~6369632o2629 205400 2 636w 20SSO0 0900 / 205600 DATA NCAS [/ 1~ 29 39 6 t 6~ 20STo0 1 To 6 / 20S600 (ND 205900 )* m 0

Real-Time Performance of a Self-Powered Environmental IoT Sensor Network System.

PubMed

Wu, Fan; Rüdiger, Christoph; Yuce, Mehmet Rasit

2017-02-01

Wireless sensor networks (WSNs) play an increasingly important role in monitoring applications in many areas. With the emergence of the Internet-of-Things (IoT), many more lowpower sensors will need to be deployed in various environments to collect and monitor data about environmental factors in real time. Providing power supply to these sensor nodes becomes a critical challenge for realizations of IoT applications as sensor nodes are normally battery-powered and have a limited lifetime. This paper proposes a wireless sensor network that is powered by solar energy harvesting. The sensor network monitors the environmental data with low-power sensor electronics and forms a network using multiple XBee wireless modules. A detailed performance analysis of the network system under solar energy harvesting has been presented. The sensor network system and the proposed energy-harvesting techniques are configured to achieve a continuous energy source for the sensor network. The proposed energy-harvesting system has been successfully designed to enable an energy solution in order to keep sensor nodes active and reliable for a whole day. The paper also outlines some of our experiences in real-time implementation of a sensor network system with energy harvesting.

Real-Time Performance of a Self-Powered Environmental IoT Sensor Network System

PubMed Central

Wu, Fan; Rüdiger, Christoph; Yuce, Mehmet Rasit

2017-01-01

Wireless sensor networks (WSNs) play an increasingly important role in monitoring applications in many areas. With the emergence of the Internet-of-Things (IoT), many more low-power sensors will need to be deployed in various environments to collect and monitor data about environmental factors in real time. Providing power supply to these sensor nodes becomes a critical challenge for realizations of IoT applications as sensor nodes are normally battery-powered and have a limited lifetime. This paper proposes a wireless sensor network that is powered by solar energy harvesting. The sensor network monitors the environmental data with low-power sensor electronics and forms a network using multiple XBee wireless modules. A detailed performance analysis of the network system under solar energy harvesting has been presented. The sensor network system and the proposed energy-harvesting techniques are configured to achieve a continuous energy source for the sensor network. The proposed energy-harvesting system has been successfully designed to enable an energy solution in order to keep sensor nodes active and reliable for a whole day. The paper also outlines some of our experiences in real-time implementation of a sensor network system with energy harvesting. PMID:28157148

Design and development of an IoT-based web application for an intelligent remote SCADA system

NASA Astrophysics Data System (ADS)

Kao, Kuang-Chi; Chieng, Wei-Hua; Jeng, Shyr-Long

2018-03-01

This paper presents a design of an intelligent remote electrical power supervisory control and data acquisition (SCADA) system based on the Internet of Things (IoT), with Internet Information Services (IIS) for setting up web servers, an ASP.NET model-view- controller (MVC) for establishing a remote electrical power monitoring and control system by using responsive web design (RWD), and a Microsoft SQL Server as the database. With the web browser connected to the Internet, the sensing data is sent to the client by using the TCP/IP protocol, which supports mobile devices with different screen sizes. The users can provide instructions immediately without being present to check the conditions, which considerably reduces labor and time costs. The developed system incorporates a remote measuring function by using a wireless sensor network and utilizes a visual interface to make the human-machine interface (HMI) more instinctive. Moreover, it contains an analog input/output and a basic digital input/output that can be applied to a motor driver and an inverter for integration with a remote SCADA system based on IoT, and thus achieve efficient power management.

Photoelectron spectroscopy and theoretical study of M(IO3)2(-) (M = H, Li, Na, K): structural evolution, optical isomers, and hyperhalogen behavior.

PubMed

Hou, Gao-Lei; Wu, Miao Miao; Wen, Hui; Sun, Qiang; Wang, Xue-Bin; Zheng, Wei-Jun

2013-07-28

H(IO3)2(-) and M(IO3)2(-) (M = Li, Na, K) anions were successfully produced via electrospray ionization of their corresponding bulk salt solutions, and were characterized by combining negative ion photoelectron spectroscopy and quantum chemical calculations. The experimental vertical detachment energies (VDEs) of M(IO3)2(-) (M = H, Li, Na, K) are 6.25, 6.57, 6.60, and 6.51 eV, respectively, and they are much higher than that of IO3(-) (4.77 eV). The theoretical calculations show that each of these anions has two energetically degenerate optical isomers. It is found that the structure of H(IO3)2(-) can be written as IO3(-)(HIO3), in which the H atom is tightly bound to one of the IO3(-) groups and forms an iodic acid (HIO3) molecule; while the structures of M(IO3)2(-) can be written as (IO3(-))M(+)(IO3(-)), in which the alkali metal atoms interact with the two IO3(-) groups almost equally and bridge the two IO3(-) groups via two O atoms of each IO3(-) with the two MOOI planes nearly perpendicular to each other. In addition, the high VDEs of M(IO3)2(-) (M = Li, Na, K) can be explained by the hyperhalogen behavior of their neutral counterparts.

A Lightweight, High-performance I/O Management Package for Data-intensive Computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jun Wang

2007-07-17

File storage systems are playing an increasingly important role in high-performance computing as the performance gap between CPU and disk increases. It could take a long time to develop an entire system from scratch. Solutions will have to be built as extensions to existing systems. If new portable, customized software components are plugged into these systems, better sustained high I/O performance and higher scalability will be achieved, and the development cycle of next-generation of parallel file systems will be shortened. The overall research objective of this ECPI development plan aims to develop a lightweight, customized, high-performance I/O management package namedmore » LightI/O to extend and leverage current parallel file systems used by DOE. During this period, We have developed a novel component in LightI/O and prototype them into PVFS2, and evaluate the resultant prototype—extended PVFS2 system on data-intensive applications. The preliminary results indicate the extended PVFS2 delivers better performance and reliability to users. A strong collaborative effort between the PI at the University of Nebraska Lincoln and the DOE collaborators—Drs Rob Ross and Rajeev Thakur at Argonne National Laboratory who are leading the PVFS2 group makes the project more promising.« less

Pattern Generator for Bench Test of Digital Boards

NASA Technical Reports Server (NTRS)

Berkun, Andrew C.; Chu, Anhua J.

2012-01-01

All efforts to develop electronic equipment reach a stage where they need a board test station for each board. The SMAP digital system consists of three board types that interact with each other using interfaces with critical timing. Each board needs to be tested individually before combining into the integrated digital electronics system. Each board needs critical timing signals from the others to be able to operate. A bench test system was developed to support test of each board. The test system produces all the outputs of the control and timing unit, and is delivered much earlier than the timing unit. Timing signals are treated as data. A large file is generated containing the state of every timing signal at any instant. This file is streamed out to an IO card, which is wired directly to the device-under-test (DUT) input pins. This provides a flexible test environment that can be adapted to any of the boards required to test in a standalone configuration. The problem of generating the critical timing signals is then transferred from a hardware problem to a software problem where it is more easily dealt with.

Importance of balanced architectures in the design of high-performance imaging systems

NASA Astrophysics Data System (ADS)

Sgro, Joseph A.; Stanton, Paul C.

1999-03-01

Imaging systems employed in demanding military and industrial applications, such as automatic target recognition and computer vision, typically require real-time high-performance computing resources. While high- performances computing systems have traditionally relied on proprietary architectures and custom components, recent advances in high performance general-purpose microprocessor technology have produced an abundance of low cost components suitable for use in high-performance computing systems. A common pitfall in the design of high performance imaging system, particularly systems employing scalable multiprocessor architectures, is the failure to balance computational and memory bandwidth. The performance of standard cluster designs, for example, in which several processors share a common memory bus, is typically constrained by memory bandwidth. The symptom characteristic of this problem is failure to the performance of the system to scale as more processors are added. The problem becomes exacerbated if I/O and memory functions share the same bus. The recent introduction of microprocessors with large internal caches and high performance external memory interfaces makes it practical to design high performance imaging system with balanced computational and memory bandwidth. Real word examples of such designs will be presented, along with a discussion of adapting algorithm design to best utilize available memory bandwidth.

Geologic map of Io

USGS Publications Warehouse

Williams, David A.; Keszthelyi, Laszlo P.; Crown, David A.; Yff, Jessica A.; Jaeger, Windy L.; Schenk, Paul M.; Geissler, Paul E.; Becker, Tammy L.

2011-01-01

Io, discovered by Galileo Galilei on January 7–13, 1610, is the innermost of the four Galilean satellites of the planet Jupiter (Galilei, 1610). It is the most volcanically active object in the Solar System, as recognized by observations from six National Aeronautics and Space Administration (NASA) spacecraft: Voyager 1 (March 1979), Voyager 2 (July 1979), Hubble Space Telescope (1990–present), Galileo (1996–2001), Cassini (December 2000), and New Horizons (February 2007). The lack of impact craters on Io in any spacecraft images at any resolution attests to the high resurfacing rate (1 cm/yr) and the dominant role of active volcanism in shaping its surface. High-temperature hot spots detected by the Galileo Solid-State Imager (SSI), Near-Infrared Mapping Spectrometer (NIMS), and Photopolarimeter-Radiometer (PPR) usually correlate with darkest materials on the surface, suggesting active volcanism. The Voyager flybys obtained complete coverage of Io's subjovian hemisphere at 500 m/pixel to 2 km/pixel, and most of the rest of the satellite at 5–20 km/pixel. Repeated Galileo flybys obtained complementary coverage of Io's antijovian hemisphere at 5 m/pixel to 1.4 km/pixel. Thus, the Voyager and Galileo data sets were merged to enable the characterization of the whole surface of the satellite at a consistent resolution. The United States Geological Survey (USGS) produced a set of four global mosaics of Io in visible wavelengths at a spatial resolution of 1 km/pixel, released in February 2006, which we have used as base maps for this new global geologic map. Much has been learned about Io's volcanism, tectonics, degradation, and interior since the Voyager flybys, primarily during and following the Galileo Mission at Jupiter (December 1995–September 2003), and the results have been summarized in books published after the end of the Galileo Mission. Our mapping incorporates this new understanding to assist in map unit definition and to provide a global synthesis of Io's geology.

Using Formal Grammars to Predict I/O Behaviors in HPC: The Omnisc'IO Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorier, Matthieu; Ibrahim, Shadi; Antoniu, Gabriel

2016-08-01

The increasing gap between the computation performance of post-petascale machines and the performance of their I/O subsystem has motivated many I/O optimizations including prefetching, caching, and scheduling. In order to further improve these techniques, modeling and predicting spatial and temporal I/O patterns of HPC applications as they run has become crucial. In this paper we present Omnisc'IO, an approach that builds a grammar-based model of the I/O behavior of HPC applications and uses it to predict when future I/O operations will occur, and where and how much data will be accessed. To infer grammars, Omnisc'IO is based on StarSequitur, amore » novel algorithm extending Nevill-Manning's Sequitur algorithm. Omnisc'IO is transparently integrated into the POSIX and MPI I/O stacks and does not require any modification in applications or higher-level I/O libraries. It works without any prior knowledge of the application and converges to accurate predictions of any N future I/O operations within a couple of iterations. Its implementation is efficient in both computation time and memory footprint.« less

Ah!Help: A generalized on-line help facility

NASA Technical Reports Server (NTRS)

Yu, Wong Nai; Mantooth, Charmiane; Soulahakil, Alex

1986-01-01

The idea behind the help facility discussed is relatively simple. It is made unique by the fact that it is written in Ada and uses aspects of the language which make information retrieval rapid and simple. Specifically, the DIRECT IO facility allows for random access into the help files. It is necessary to discuss the advantages of random access over sequential access. The mere fact that the program in written in Ada implies a saving in terms of lines of code. This introduces the possibility of eventually adapting the program to run at the microcomputer level, a major consideration . Additionally, since the program uses only standard Ada generics, it is portable to other systems. This is another aspect which must always be taken into consideration in writting any software package in the modern day world of computer programming.

Multi-Purpose, Application-Centric, Scalable I/O Proxy Application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, M. C.

2015-06-15

MACSio is a Multi-purpose, Application-Centric, Scalable I/O proxy application. It is designed to support a number of goals with respect to parallel I/O performance testing and benchmarking including the ability to test and compare various I/O libraries and I/O paradigms, to predict scalable performance of real applications and to help identify where improvements in I/O performance can be made within the HPC I/O software stack.

Design and Implementation of Cloud-Centric Configuration Repository for DIY IoT Applications

PubMed Central

Ahmad, Shabir; Kim, Do Hyeun

2018-01-01

The Do-It-Yourself (DIY) vision for the design of a smart and customizable IoT application demands the involvement of the general public in its development process. The general public lacks the technical knowledge for programming state-of-the-art prototyping and development kits. The latest IoT kits, for example, Raspberry Pi, are revolutionizing the DIY paradigm for IoT, and more than ever, a DIY intuitive programming interface is required to enable the masses to interact with and customize the behavior of remote IoT devices on the Internet. However, in most cases, these DIY toolkits store the resultant configuration data in local storage and, thus, cannot be accessed remotely. This paper presents the novel implementation of such a system, which not only enables the general public to customize the behavior of remote IoT devices through a visual interface, but also makes the configuration available everywhere and anytime by leveraging the power of cloud-based platforms. The interface enables the visualization of the resources exposed by remote embedded resources in the form of graphical virtual objects (VOs). These VOs are used to create the service design through simple operations like drag-and-drop and the setting of properties. The configuration created as a result is maintained as an XML document, which is ingested by the cloud platform, thus making it available to be used anywhere. We use the HTTP approach for the communication between the cloud and IoT toolbox and the cloud and real devices, but for communication between the toolbox and actual resources, CoAP is used. Finally, a smart home case study has been implemented and presented in order to assess the effectiveness of the proposed work. PMID:29415450

Design and Implementation of Cloud-Centric Configuration Repository for DIY IoT Applications.

PubMed

Ahmad, Shabir; Hang, Lei; Kim, Do Hyeun

2018-02-06

The Do-It-Yourself (DIY) vision for the design of a smart and customizable IoT application demands the involvement of the general public in its development process. The general public lacks the technical knowledge for programming state-of-the-art prototyping and development kits. The latest IoT kits, for example, Raspberry Pi, are revolutionizing the DIY paradigm for IoT, and more than ever, a DIY intuitive programming interface is required to enable the masses to interact with and customize the behavior of remote IoT devices on the Internet. However, in most cases, these DIY toolkits store the resultant configuration data in local storage and, thus, cannot be accessed remotely. This paper presents the novel implementation of such a system, which not only enables the general public to customize the behavior of remote IoT devices through a visual interface, but also makes the configuration available everywhere and anytime by leveraging the power of cloud-based platforms. The interface enables the visualization of the resources exposed by remote embedded resources in the form of graphical virtual objects (VOs). These VOs are used to create the service design through simple operations like drag-and-drop and the setting of properties. The configuration created as a result is maintained as an XML document, which is ingested by the cloud platform, thus making it available to be used anywhere. We use the HTTP approach for the communication between the cloud and IoT toolbox and the cloud and real devices, but for communication between the toolbox and actual resources, CoAP is used. Finally, a smart home case study has been implemented and presented in order to assess the effectiveness of the proposed work.

A Lightweight I/O Scheme to Facilitate Spatial and Temporal Queries of Scientific Data Analytics

NASA Technical Reports Server (NTRS)

Tian, Yuan; Liu, Zhuo; Klasky, Scott; Wang, Bin; Abbasi, Hasan; Zhou, Shujia; Podhorszki, Norbert; Clune, Tom; Logan, Jeremy; Yu, Weikuan

2013-01-01

In the era of petascale computing, more scientific applications are being deployed on leadership scale computing platforms to enhance the scientific productivity. Many I/O techniques have been designed to address the growing I/O bottleneck on large-scale systems by handling massive scientific data in a holistic manner. While such techniques have been leveraged in a wide range of applications, they have not been shown as adequate for many mission critical applications, particularly in data post-processing stage. One of the examples is that some scientific applications generate datasets composed of a vast amount of small data elements that are organized along many spatial and temporal dimensions but require sophisticated data analytics on one or more dimensions. Including such dimensional knowledge into data organization can be beneficial to the efficiency of data post-processing, which is often missing from exiting I/O techniques. In this study, we propose a novel I/O scheme named STAR (Spatial and Temporal AggRegation) to enable high performance data queries for scientific analytics. STAR is able to dive into the massive data, identify the spatial and temporal relationships among data variables, and accordingly organize them into an optimized multi-dimensional data structure before storing to the storage. This technique not only facilitates the common access patterns of data analytics, but also further reduces the application turnaround time. In particular, STAR is able to enable efficient data queries along the time dimension, a practice common in scientific analytics but not yet supported by existing I/O techniques. In our case study with a critical climate modeling application GEOS-5, the experimental results on Jaguar supercomputer demonstrate an improvement up to 73 times for the read performance compared to the original I/O method.

Magnetically engineered SnO2 quantum dots as a bimodal agent for optical and magnetic resonance imaging

NASA Astrophysics Data System (ADS)

Dutta, Dipa; Gupta, Jagriti; Thakur, Dinbandhu; Bahadur, Dhirendra

2017-12-01

Combining more than one imaging technique into a single system can outweigh the limitations of conventional imaging techniques. Pairing optically active quantum dots (QDs) with superparamagnetic MRI agent is an adorable way to develop probes for bimodal imaging. Tiny SnO2 quantum dot embedded iron oxide (IO) nanocomposite (SQD-IO) is synthesized. This combines the superparamagnetic property of IO nanoparticles (NPs) and special optical properties of SnO2 QDs, and is explored as a bimodal imaging agent. Morphological studies of the nanocomposite reveal that 3 nm tiny SnO2 QDs are embedded in ~30 nm γ-Fe2O3 NPs. The SQD-IO preserves the intrinsic superparamagnetic behaviour of its constituent IO NPs with a magnetization ~21.4 emu g-1 measured at an applied field of 20k Oe. The emission colour of the nanocomposite is tuned by simply varying the excitation wavelength. The centre of the emission band shifts from 570 to 600 nm as the excitation alters from 488 to 535 nm. The cytotoxicity assessment indicates that the nanocomposite is suitable for its in vitro use. Transverse proton relaxivity (141 mM-1 s-1) of the nanocomposite is higher than the widely used negative contrast agent Feridex (R2  =  98.3 mM-1 s-1). The confocal laser scanning microscope images give evidence of the cellular uptake behaviour of SQD-IO in HeLa cells and it is seen that QDs retain their optical properties within the intracellular environment. The high R2 value for MRI and the tunable florescence images of HeLa cells essentially establish SQD-IO as a potential probe for bimodal imaging.

High performance network and channel-based storage

NASA Technical Reports Server (NTRS)

Katz, Randy H.

1991-01-01

In the traditional mainframe-centered view of a computer system, storage devices are coupled to the system through complex hardware subsystems called input/output (I/O) channels. With the dramatic shift towards workstation-based computing, and its associated client/server model of computation, storage facilities are now found attached to file servers and distributed throughout the network. We discuss the underlying technology trends that are leading to high performance network-based storage, namely advances in networks, storage devices, and I/O controller and server architectures. We review several commercial systems and research prototypes that are leading to a new approach to high performance computing based on network-attached storage.

Least mean square fourth based microgrid state estimation algorithm using the internet of things technology

PubMed Central

2017-01-01

This paper proposes an innovative internet of things (IoT) based communication framework for monitoring microgrid under the condition of packet dropouts in measurements. First of all, the microgrid incorporating the renewable distributed energy resources is represented by a state-space model. The IoT embedded wireless sensor network is adopted to sense the system states. Afterwards, the information is transmitted to the energy management system using the communication network. Finally, the least mean square fourth algorithm is explored for estimating the system states. The effectiveness of the developed approach is verified through numerical simulations. PMID:28459848

The Galilean Satellites

NASA Image and Video Library

1997-11-18

This composite includes the four largest moons of Jupiter which are known as the Galilean satellites. From left to right, the moons shown are Ganymede, Callisto, Io, and Europa. The Galilean satellites were first seen by the Italian astronomer Galileo Galilei in 1610. In order of increasing distance from Jupiter, Io is closest, followed by Europa, Ganymede, and Callisto. The order of these satellites from the planet Jupiter helps to explain some of the visible differences among the moons. Io is subject to the strongest tidal stresses from the massive planet. These stresses generate internal heating which is released at the surface and makes Io the most volcanically active body in our solar system. Europa appears to be strongly differentiated with a rock/iron core, an ice layer at its surface, and the potential for local or global zones of water between these layers. Tectonic resurfacing brightens terrain on the less active and partially differentiated moon Ganymede. Callisto, furthest from Jupiter, appears heavily cratered at low resolutions and shows no evidence of internal activity. North is to the top of this composite picture in which these satellites have all been scaled to a common factor of 10 kilometers (6 miles) per picture element. The Solid State Imaging (CCD) system aboard NASA's Galileo spacecraft obtained the Io and Ganymede images in June 1996, while the Europa images were obtained in September 1996. Because Galileo focuses on high resolution imaging of regional areas on Callisto rather than global coverage, the portrait of Callisto is from the 1979 flyby of NASA's Voyager spacecraft. http://photojournal.jpl.nasa.gov/catalog/PIA00601

Impulse oscillometry system as an alternative diagnostic method for chronic obstructive pulmonary disease.

PubMed

Wei, Xia; Shi, Zhihong; Cui, Yajuan; Mi, Jiuyun; Ma, Zhengquan; Ren, Jingting; Li, Jie; Xu, Shudi; Guo, Youmin

2017-11-01

We aimed to compare impulse oscillation system (IOS) and traditional pulmonary function tests (PFTs) for the assessment of the severity of chronic obstructive pulmonary disease (COPD), and to assess the use of IOS parameters to identify patients who were forced expiratory volume in 1 second (FEV1)%pred < 50%.Patients with COPD (n = 215) were enrolled at the Ninth Hospital of Xi'an Affiliated Hospital of Xi'an Jiaotong University between October 2014 and September 2016. All patients were assessed by traditional PFT and IOS. Diagnostic performance of IOS parameters to determine indication for patients of FEV1%pred < 50% was assessed on receiver-operating characteristics (ROC) curve analysis.Out of 215 patients, 18, 83, 78, and 36 patients were classified as grade 1, 2, 3, and 4, respectively, according to the Global Initiative for Chronic Obstructive Lung Disease (GOLD) severity grading. On Spearman correlation analysis, FEV1%pred, MMEF 75%-25%, and residual volume/total lung capacity (RV/TLC) correlated with total respiratory impedance (Z5)%pred, resistance at 5 Hz (R5)-resistance at 20 Hz (R20), R5-R20% R5, R5, R5%pred, frequency response (Fres), reactance area (Ax), and reactance at 5 Hz (X5). On ROC curve analysis, the area under the curve (AUC) of X5 absolute value, Fres, Ax, Z5%pred, R5-R20, and R5-R20% R5 were 0.748, 0.755, 0.760, 0.705, 0.715, and 0.735, respectively, for COPD patients who required inhalational glucocorticoid therapy.IOS parameters showed a good correlation with traditional pulmonary function parameters; reactance parameters showed a stronger correlation than that of the resistance parameters. IOS can be used as an alternative method for pulmonary function assessment in patients with COPD with FEV1%pred < 50% who need inhalational glucocorticoid therapy. ChiCTR-OCH-14004904.

Impulse oscillometry system as an alternative diagnostic method for chronic obstructive pulmonary disease

PubMed Central

Wei, Xia; Shi, Zhihong; Cui, Yajuan; Mi, Jiuyun; Ma, Zhengquan; Ren, Jingting; Li, Jie; Xu, Shudi; Guo, Youmin

2017-01-01

Abstract We aimed to compare impulse oscillation system (IOS) and traditional pulmonary function tests (PFTs) for the assessment of the severity of chronic obstructive pulmonary disease (COPD), and to assess the use of IOS parameters to identify patients who were forced expiratory volume in 1 second (FEV1)%pred < 50%. Patients with COPD (n = 215) were enrolled at the Ninth Hospital of Xi’an Affiliated Hospital of Xi’an Jiaotong University between October 2014 and September 2016. All patients were assessed by traditional PFT and IOS. Diagnostic performance of IOS parameters to determine indication for patients of FEV1%pred < 50% was assessed on receiver-operating characteristics (ROC) curve analysis. Out of 215 patients, 18, 83, 78, and 36 patients were classified as grade 1, 2, 3, and 4, respectively, according to the Global Initiative for Chronic Obstructive Lung Disease (GOLD) severity grading. On Spearman correlation analysis, FEV1%pred, MMEF 75%–25%, and residual volume/total lung capacity (RV/TLC) correlated with total respiratory impedance (Z5)%pred, resistance at 5 Hz (R5)-resistance at 20 Hz (R20), R5-R20% R5, R5, R5%pred, frequency response (Fres), reactance area (Ax), and reactance at 5 Hz (X5). On ROC curve analysis, the area under the curve (AUC) of X5 absolute value, Fres, Ax, Z5%pred, R5-R20, and R5-R20% R5 were 0.748, 0.755, 0.760, 0.705, 0.715, and 0.735, respectively, for COPD patients who required inhalational glucocorticoid therapy. IOS parameters showed a good correlation with traditional pulmonary function parameters; reactance parameters showed a stronger correlation than that of the resistance parameters. IOS can be used as an alternative method for pulmonary function assessment in patients with COPD with FEV1%pred < 50% who need inhalational glucocorticoid therapy. Clinical trial registration number: ChiCTR-OCH-14004904. PMID:29145259

Integrated Method for Personal Thermal Comfort Assessment and Optimization through Users' Feedback, IoT and Machine Learning: A Case Study †.

PubMed

Salamone, Francesco; Belussi, Lorenzo; Currò, Cristian; Danza, Ludovico; Ghellere, Matteo; Guazzi, Giulia; Lenzi, Bruno; Megale, Valentino; Meroni, Italo

2018-05-17

Thermal comfort has become a topic issue in building performance assessment as well as energy efficiency. Three methods are mainly recognized for its assessment. Two of them based on standardized methodologies, face the problem by considering the indoor environment in steady-state conditions (PMV and PPD) and users as active subjects whose thermal perception is influenced by outdoor climatic conditions (adaptive approach). The latter method is the starting point to investigate thermal comfort from an overall perspective by considering endogenous variables besides the traditional physical and environmental ones. Following this perspective, the paper describes the results of an in-field investigation of thermal conditions through the use of nearable and wearable solutions, parametric models and machine learning techniques. The aim of the research is the exploration of the reliability of IoT-based solutions combined with advanced algorithms, in order to create a replicable framework for the assessment and improvement of user thermal satisfaction. For this purpose, an experimental test in real offices was carried out involving eight workers. Parametric models are applied for the assessment of thermal comfort; IoT solutions are used to monitor the environmental variables and the users' parameters; the machine learning CART method allows to predict the users' profile and the thermal comfort perception respect to the indoor environment.

Integrated Method for Personal Thermal Comfort Assessment and Optimization through Users’ Feedback, IoT and Machine Learning: A Case Study †

PubMed Central

Currò, Cristian; Danza, Ludovico; Ghellere, Matteo; Guazzi, Giulia; Lenzi, Bruno; Megale, Valentino; Meroni, Italo

2018-01-01

Thermal comfort has become a topic issue in building performance assessment as well as energy efficiency. Three methods are mainly recognized for its assessment. Two of them based on standardized methodologies, face the problem by considering the indoor environment in steady-state conditions (PMV and PPD) and users as active subjects whose thermal perception is influenced by outdoor climatic conditions (adaptive approach). The latter method is the starting point to investigate thermal comfort from an overall perspective by considering endogenous variables besides the traditional physical and environmental ones. Following this perspective, the paper describes the results of an in-field investigation of thermal conditions through the use of nearable and wearable solutions, parametric models and machine learning techniques. The aim of the research is the exploration of the reliability of IoT-based solutions combined with advanced algorithms, in order to create a replicable framework for the assessment and improvement of user thermal satisfaction. For this purpose, an experimental test in real offices was carried out involving eight workers. Parametric models are applied for the assessment of thermal comfort; IoT solutions are used to monitor the environmental variables and the users’ parameters; the machine learning CART method allows to predict the users’ profile and the thermal comfort perception respect to the indoor environment. PMID:29772818

Development Of A Numerical Tow Tank With Wave Generation To Supplement Experimental Efforts

DTIC Science & Technology

2017-12-01

vehicles CAD computer aided design CFD computational fluid dynamics FVM finite volume method IO information operations ISR intelligence, surveillance, and...deliver a product that I am truly proud of. xv THIS PAGE INTENTIONALLY LEFT BLANK xvi CHAPTER 1: Introduction 1.1 Importance of Tow Tank Testing Modern...wedge installation. 1 In 2016, NPS student Ensign Ryan Tran adapted an existing vertical plunging wedge wave maker design used at the U.S. Naval

Approximate Sensory Data Collection: A Survey

PubMed Central

Cheng, Siyao; Cai, Zhipeng; Li, Jianzhong

2017-01-01

With the rapid development of the Internet of Things (IoTs), wireless sensor networks (WSNs) and related techniques, the amount of sensory data manifests an explosive growth. In some applications of IoTs and WSNs, the size of sensory data has already exceeded several petabytes annually, which brings too many troubles and challenges for the data collection, which is a primary operation in IoTs and WSNs. Since the exact data collection is not affordable for many WSN and IoT systems due to the limitations on bandwidth and energy, many approximate data collection algorithms have been proposed in the last decade. This survey reviews the state of the art of approximate data collection algorithms. We classify them into three categories: the model-based ones, the compressive sensing based ones, and the query-driven ones. For each category of algorithms, the advantages and disadvantages are elaborated, some challenges and unsolved problems are pointed out, and the research prospects are forecasted. PMID:28287440

IoT real time data acquisition using MQTT protocol

NASA Astrophysics Data System (ADS)

Atmoko, R. A.; Riantini, R.; Hasin, M. K.

2017-05-01

The Internet of Things (IoT) provides ease to monitor and to gain sensor data through the Internet [1]. The need of high quality data is increasing to the extent that data monitoring and acquisition system in real time is required, such as smart city or telediagnostic in medical areas [2]. Therefore, an appropriate communication protocol is required to resolve these problems. Lately, researchers have developed a lot of communication protocols for IoT, of which each has advantages and disadvantages. This study proposes the utilization of MQTT as a communication protocol, which is one of data communication protocols for IoT. This study used temperature and humidity sensors because the physical parameters are often needed as parameters of environment condition [3]. Data acquisition was done in real-time and stored in MySQL database. This study is also completed by interface web-based and mobile for online monitoring. This result of this study is the enhancement of data quality and reliability using MQTT protocol.

Lunar and Planetary Science XXXV: Outer Solar System

NASA Technical Reports Server (NTRS)

2004-01-01

The session 'Outer Solar System" inlcuded:Monte Carlo Modeling of [O I] 630 nm Auroral Emission on Io; The Detection of Iron Sulfide on Io; Io and Loki in 2003 as Seen from the Infrared Telescope Facility Using Mutual Satellite and Jupiter Occultations; Mapping of the Zamama-Thor Region of Io; First Solar System Results of the Spitzer Space Telescope; Mapping the Surface of Pluto with the Hubble Space Telescope; Experimental Study on Fischer-Tropsch Catalysis in the Circum-Saturnian Subnebula; New High-Pressure Phases of Ammonia Dihydrate; Gas Hydrate Stability at Low Temperatures and High Pressures with Applications to Mars and Europa; Laboratory UV Photolysis of Planetary Ice Analogs Containing H2O + CO2 (1:1); The OH Stretch Infrared Band of Water Ice and Its Temperature and Radiation Dependence; Band Position Variations in Reflectance Spectra of the Jovian Satellite Ganymede; Comparison of Porosity and Radar Models for Europa s Near Surface; Combined Effects of Diurnal and Nonsynchronous Surface Stresses on Europa; Europa s Northern Trailing Hemisphere: Lineament Stratigraphic Framework; Europa at the Highest Resolution: Implications for Surface Processes and Landing Sites; Comparison of Methods to Determine Furrow System Centers on Ganymede and Callisto; Resurfacing of Ganymede by Liquid-Water Volcanism; Layered Ejecta Craters on Ganymede: Comparisons with Martian Analogs; Evaluation of the Possible Presence of CO2-Clathrates in Europa s Icy Shell or Seafloor; Geosciences at Jupiter s Icy Moons: The Midas Touch; Planetary Remote Sensing Science Enabled by MIDAS (Multiple Instrument Distributed Aperture Sensor); and In Situ Surveying of Saturn s Rings.

An Efficient User Authentication and User Anonymity Scheme with Provably Security for IoT-Based Medical Care System

PubMed Central

Wu, Tsu-Yang; Chen, Chin-Ling; Lee, Cheng-Chi; Chen, Chien-Ming

2017-01-01

In recent years, with the increase in degenerative diseases and the aging population in advanced countries, demands for medical care of older or solitary people have increased continually in hospitals and healthcare institutions. Applying wireless sensor networks for the IoT-based telemedicine system enables doctors, caregivers or families to monitor patients’ physiological conditions at anytime and anyplace according to the acquired information. However, transmitting physiological data through the Internet concerns the personal privacy of patients. Therefore, before users can access medical care services in IoT-based medical care system, they must be authenticated. Typically, user authentication and data encryption are most critical for securing network communications over a public channel between two or more participants. In 2016, Liu and Chung proposed a bilinear pairing-based password authentication scheme for wireless healthcare sensor networks. They claimed their authentication scheme cannot only secure sensor data transmission, but also resist various well-known security attacks. In this paper, we demonstrate that Liu–Chung’s scheme has some security weaknesses, and we further present an improved secure authentication and data encryption scheme for the IoT-based medical care system, which can provide user anonymity and prevent the security threats of replay and password/sensed data disclosure attacks. Moreover, we modify the authentication process to reduce redundancy in protocol design, and the proposed scheme is more efficient in performance compared with previous related schemes. Finally, the proposed scheme is provably secure in the random oracle model under ECDHP. PMID:28644381

An IoT Reader for Wireless Passive Electromagnetic Sensors.

PubMed

Galindo-Romera, Gabriel; Carnerero-Cano, Javier; Martínez-Martínez, José Juan; Herraiz-Martínez, Francisco Javier

2017-03-28

In the last years, many passive electromagnetic sensors have been reported. Some of these sensors are used for measuring harmful substances. Moreover, the response of these sensors is usually obtained with laboratory equipment. This approach highly increases the total cost and complexity of the sensing system. In this work, a novel low-cost and portable Internet-of-Things (IoT) reader for passive wireless electromagnetic sensors is proposed. The reader is used to interrogate the sensors within a short-range wireless link avoiding the direct contact with the substances under test. The IoT functionalities of the reader allows remote sensing from computers and handheld devices. For that purpose, the proposed design is based on four functional layers: the radiating layer, the RF interface, the IoT mini-computer and the power unit. In this paper a demonstrator of the proposed reader is designed and manufactured. The demonstrator shows, through the remote measurement of different substances, that the proposed system can estimate the dielectric permittivity. It has been demonstrated that a linear approximation with a small error can be extracted from the reader measurements. It is remarkable that the proposed reader can be used with other type of electromagnetic sensors, which transduce the magnitude variations in the frequency domain.

An IoT Reader for Wireless Passive Electromagnetic Sensors

PubMed Central

Galindo-Romera, Gabriel; Carnerero-Cano, Javier; Martínez-Martínez, José Juan; Herraiz-Martínez, Francisco Javier

2017-01-01

In the last years, many passive electromagnetic sensors have been reported. Some of these sensors are used for measuring harmful substances. Moreover, the response of these sensors is usually obtained with laboratory equipment. This approach highly increases the total cost and complexity of the sensing system. In this work, a novel low-cost and portable Internet-of-Things (IoT) reader for passive wireless electromagnetic sensors is proposed. The reader is used to interrogate the sensors within a short-range wireless link avoiding the direct contact with the substances under test. The IoT functionalities of the reader allows remote sensing from computers and handheld devices. For that purpose, the proposed design is based on four functional layers: the radiating layer, the RF interface, the IoT mini-computer and the power unit. In this paper a demonstrator of the proposed reader is designed and manufactured. The demonstrator shows, through the remote measurement of different substances, that the proposed system can estimate the dielectric permittivity. It has been demonstrated that a linear approximation with a small error can be extracted from the reader measurements. It is remarkable that the proposed reader can be used with other type of electromagnetic sensors, which transduce the magnitude variations in the frequency domain. PMID:28350356

Pain assessment by children and adolescents during intraosseous anaesthesia using a computerized system (QuickSleeper).

PubMed

Sixou, Jean-Louis; Marie-Cousin, Alexia; Huet, Adeline; Hingant, Bernard; Robert, Jean-Claude

2009-09-01

Intraosseous (IO) anaesthesia has been shown to be effective in children. However, the pain associated with anaesthetic injections, and its acceptance by children, have never been studied. The aim of this study was to assess the pain associated with the IO injection of 4% articaine with 1 : 200 000 epinephrine using the computerized QuickSleeper' system in a population of children and adolescents. IO anaesthesia was performed on patients aged 10.4 +/- 2.6 years of age. The patients assessed their pain on a faces pain scale (FPS) and on a visual analogue scale (VAS). The operators were also asked to assess signs of patient pain/discomfort. No pain or mild discomfort was reported by, respectively, 81.8% (FPS) and 83.9% (VAS) of the patients. Some 58.9% of children with previous experience of dental anaesthesia reported that computerized IO anaesthesia was more comfortable than traditional infiltration methods. Operators noted signs of discomfort during penetration and injection in 18.3% and 25.3% of the patients, respectively. This study showed that the majority of children reported no pain or mild pain when anaesthetic was administered by computerized needle rotation and solution deposition. This technique holds promise for use by trained paediatric dentists.

Virtualized MME Design for IoT Support in 5G Systems.

PubMed

Andres-Maldonado, Pilar; Ameigeiras, Pablo; Prados-Garzon, Jonathan; Ramos-Munoz, Juan Jose; Lopez-Soler, Juan Manuel

2016-08-22

Cellular systems are recently being considered an option to provide support to the Internet of Things (IoT). To enable this support, the 3rd Generation Partnership Project (3GPP) has introduced new procedures specifically targeted for cellular IoT. With one of these procedures, the transmissions of small and infrequent data packets from/to the devices are encapsulated in signaling messages and sent through the control plane. However, these transmissions from/to a massive number of devices may imply a major increase of the processing load on the control plane entities of the network and in particular on the Mobility Management Entity (MME). In this paper, we propose two designs of an MME based on Network Function Virtualization (NFV) that aim at facilitating the IoT support. The first proposed design partially separates the processing resources dedicated to each traffic class. The second design includes traffic shaping to control the traffic of each class. We consider three classes: Mobile Broadband (MBB), low latency Machine to Machine communications (lM2M) and delay-tolerant M2M communications. Our proposals enable reducing the processing resources and, therefore, the cost. Additionally, results show that the proposed designs lessen the impact between classes, so they ease the compliance of the delay requirements of MBB and lM2M communications.

Enhanced activation of periodate by iodine-doped granular activated carbon for organic contaminant degradation.

PubMed

Li, Xiaowan; Liu, Xitao; Lin, Chunye; Qi, Chengdu; Zhang, Huijuan; Ma, Jun

2017-08-01

In this study, iodine-doped granular activated carbon (I-GAC) was prepared and subsequently applied to activate periodate (IO 4 - ) to degrade organic contaminants at ambient temperature. The physicochemical properties of GAC and I-GAC were examined using scanning electron microscopy, N 2 adsorption/desorption, Raman spectroscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. No significant difference was observed between the two except for the existence of triiodide (I 3 - ) and pentaiodide (I 5 - ) on I-GAC. The catalytic activity of I-GAC towards IO 4 - was evaluated by the degradation of acid orange 7 (AO7), and superior catalytic performance was achieved compared with GAC. The effects of some influential parameters (preparation conditions, initial solution pH, and coexisting anions) on the catalytic ability were also investigated. Based on radical scavenging experiments, it appeared that IO 3 was the predominant reactive species in the I-GAC/IO 4 - system. The mechanism underlying the enhanced catalytic performance of I-GAC could be explained by the introduction of negatively charged I 3 - and I 5 - into I-GAC, which induced positive charge density on the surface of I-GAC. This accelerated the interaction between I-GAC and IO 4 - , and subsequently mediated the increasing generation of iodyl radicals (IO 3 ). Furthermore, a possible degradation pathway of AO7 was proposed according to the intermediate products identified by gas chromatography-mass spectrometry. Copyright © 2017 Elsevier Ltd. All rights reserved.

Overview of LBTI: A Multipurpose Facility for High Spatial Resolution Observations

NASA Technical Reports Server (NTRS)

Hinz, P. M.; Defrere, D.; Skemer, A.; Bailey, V.; Stone, J.; Spalding, E.; Vaz, A.; Pinna, E.; Puglisi, A.; Esposito, S.;

Application Possibility of Smartphone as Payload for Photogrammetric Uav System

NASA Astrophysics Data System (ADS)

Yun, M. H.; Kim, J.; Seo, D.; Lee, J.; Choi, C.

2012-07-01

Smartphone can not only be operated under 3G network environment anytime and anyplace but also cost less than the existing photogrammetric UAV since it provides high-resolution image, 3D location and attitude data on a real-time basis from a variety of built-in sensors. This study is aimed to assess the possibility of smartphone as a payload for photogrammetric UAV system. Prior to such assessment, a smartphone-based photogrammetric UAV system application was developed, through which real-time image, location and attitude data was obtained using smartphone under both static and dynamic conditions. Subsequently the accuracy assessment on the location and attitude data obtained and sent by this system was conducted. The smartphone images were converted into ortho-images through image triangulation. The image triangulation was conducted in accordance with presence or absence of consideration of the interior orientation (IO) parameters determined by camera calibration. In case IO parameters were taken into account in the static experiment, the results from triangulation for any smartphone type were within 1.5 pixel (RMSE), which was improved at least by 35% compared to when IO parameters were not taken into account. On the contrary, the improvement effect of considering IO parameters on accuracy in triangulation for smartphone images in dynamic experiment was not significant compared to the static experiment. It was due to the significant impact of vibration and sudden attitude change of UAV on the actuator for automatic focus control within the camera built in smartphone under the dynamic condition. This cause appears to have a negative impact on the image-based DEM generation. Considering these study findings, it is suggested that smartphone is very feasible as a payload for UAV system. It is also expected that smartphone may be loaded onto existing UAV playing direct or indirect roles significantly.

An integrated system for land resources supervision based on the IoT and cloud computing

NASA Astrophysics Data System (ADS)

Fang, Shifeng; Zhu, Yunqiang; Xu, Lida; Zhang, Jinqu; Zhou, Peiji; Luo, Kan; Yang, Jie

2017-01-01

Integrated information systems are important safeguards for the utilisation and development of land resources. Information technologies, including the Internet of Things (IoT) and cloud computing, are inevitable requirements for the quality and efficiency of land resources supervision tasks. In this study, an economical and highly efficient supervision system for land resources has been established based on IoT and cloud computing technologies; a novel online and offline integrated system with synchronised internal and field data that includes the entire process of 'discovering breaches, analysing problems, verifying fieldwork and investigating cases' was constructed. The system integrates key technologies, such as the automatic extraction of high-precision information based on remote sensing, semantic ontology-based technology to excavate and discriminate public sentiment on the Internet that is related to illegal incidents, high-performance parallel computing based on MapReduce, uniform storing and compressing (bitwise) technology, global positioning system data communication and data synchronisation mode, intelligent recognition and four-level ('device, transfer, system and data') safety control technology. The integrated system based on a 'One Map' platform has been officially implemented by the Department of Land and Resources of Guizhou Province, China, and was found to significantly increase the efficiency and level of land resources supervision. The system promoted the overall development of informatisation in fields related to land resource management.

Anesthetic efficacy of a repeated intraosseous injection given 30 min following an inferior alveolar nerve block/intraosseous injection.

PubMed

Reitz, J; Reader, A; Nist, R; Beck, M; Meyers, W J

1998-01-01

To determine whether a repeated intraosseous (IO) injection would increase or prolong pulpal anesthesia, we measured the degree of anesthesia obtained by a repeated IO injection given 30 min following a combination inferior alveolar nerve block/intraosseous injection (IAN/IO) in mandibular second premolars and in first and second molars. Using a repeated-measures design, we randomly assigned 38 subjects to receive two combinations of injections at two separate appointments. The combinations were an IAN/IO injection followed approximately 30 min later by another IO injection of 0.9 ml of 2% lidocaine with 1:100,000 epinephrine and a combination IAN/IO injection followed approximately 30 min later by a mock IO injection. The second premolar, first molar, and second molar were blindly tested with an Analytic Technology pulp tester at 2-min cycles for 120 min postinjection. Anesthesia was considered successful when two consecutive readings of 80 were obtained. One hundred percent of the subjects had lip numbness with IAN/IO and with IAN/IO plus repeated IO techniques. Rates of anesthetic success for the IAN/IO and for the IAN/IO plus repeated IO injection, respectively, were 100% and 97% for the second premolar, 95% and 95% for the first molar, and 87% and 87% for the second molar. The repeated IO injection increased pulpal anesthesia for approximately 14 min in the second premolar and for 6 min in the first molar, but no statistically significant differences (P > 0.05) were shown. In conclusion, the repeated IO injection of 0.9 ml of 2% lidocaine with 1:100,000 epinephrine given 30 min following a combination IAN/IO injection did not significantly increase pulpal anesthesia in mandibular second premolars or in first and second molars.

I/O performance evaluation of a Linux-based network-attached storage device

NASA Astrophysics Data System (ADS)

Sun, Zhaoyan; Dong, Yonggui; Wu, Jinglian; Jia, Huibo; Feng, Guanping

2002-09-01

In a Local Area Network (LAN), clients are permitted to access the files on high-density optical disks via a network server. But the quality of read service offered by the conventional server is not satisfied because of the multiple functions on the server and the overmuch caller. This paper develops a Linux-based Network-Attached Storage (NAS) server. The Operation System (OS), composed of an optimized kernel and a miniaturized file system, is stored in a flash memory. After initialization, the NAS device is connected into the LAN. The administrator and users could configure the access the server through the web page respectively. In order to enhance the quality of access, the management of buffer cache in file system is optimized. Some benchmark programs are peformed to evaluate the I/O performance of the NAS device. Since data recorded in optical disks are usually for reading accesses, our attention is focused on the reading throughput of the device. The experimental results indicate that the I/O performance of our NAS device is excellent.

Improving Service Management in the Internet of Things

PubMed Central

Sammarco, Chiara; Iera, Antonio

2012-01-01

In the Internet of Things (IoT) research arena, many efforts are devoted to adapt the existing IP standards to emerging IoT nodes. This is the direction followed by three Internet Engineering Task Force (IETF) Working Groups, which paved the way for research on IP-based constrained networks. Through a simplification of the whole TCP/IP stack, resource constrained nodes become direct interlocutors of application level entities in every point of the network. In this paper we analyze some side effects of this solution, when in the presence of large amounts of data to transmit. In particular, we conduct a performance analysis of the Constrained Application Protocol (CoAP), a widely accepted web transfer protocol for the Internet of Things, and propose a service management enhancement that improves the exploitation of the network and node resources. This is specifically thought for constrained nodes in the abovementioned conditions and proves to be able to significantly improve the node energetic performance when in the presence of large resource representations (hence, large data transmissions).

Towards Transparent Throughput Elasticity for IaaS Cloud Storage: Exploring the Benefits of Adaptive Block-Level Caching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nicolae, Bogdan; Riteau, Pierre; Keahey, Kate

Storage elasticity on IaaS clouds is a crucial feature in the age of data-intensive computing, especially when considering fluctuations of I/O throughput. This paper provides a transparent solution that automatically boosts I/O bandwidth during peaks for underlying virtual disks, effectively avoiding over-provisioning without performance loss. The authors' proposal relies on the idea of leveraging short-lived virtual disks of better performance characteristics (and thus more expensive) to act during peaks as a caching layer for the persistent virtual disks where the application data is stored. Furthermore, they introduce a performance and cost prediction methodology that can be used both independently tomore » estimate in advance what trade-off between performance and cost is possible, as well as an optimization technique that enables better cache size selection to meet the desired performance level with minimal cost. The authors demonstrate the benefits of their proposal both for microbenchmarks and for two real-life applications using large-scale experiments.« less

Meaning in life in patients with progressive supranuclear palsy.

PubMed

Fegg, Martin Johannes; Kögler, Monika; Abright, Carina; Hensler, Mira; Lorenzl, Stefan

2014-08-01

This exploratory study investigated meaning in life (MiL) in patients with progressive supranuclear palsy (PSP). In the "Schedule for Meaning in Life Evaluation" (SMiLE), respondents list individual MiL areas before rating their current satisfaction and importance with them (index of weighting [IoW], index of satisfaction [IoS], and index of weighted satisfaction [IoWS], range 0-100). A total of 38 patients with PSP completed the SMiLE (IoS: 68.6 ± 25.6, IoW: 79.6 ± 12.6, and IoWS: 69.2 ± 26.1). A representative sample of healthy participants (n = 977) scored significantly higher in the IoS (82.8 ± 14.7, P < .001), the IoW (85.6 ± 12.3, P = .006), and the IoWS (83.3 ± 14.8, P < .001). Compared to healthy individuals, patients with PSP were less likely to list health (P = .001) and more likely to list partner (P = .04), leisure (P = .01), home/garden (P = .01), and pleasure (P = .02). Patients with PSP seem to focus on supportive relationships and leisure, while the decreasing health status is becoming less important to them. © The Author(s) 2013.

Radial and azimuthal distribution of Io's oxygen neutral cloud observed by Hisaki/EXCEED

NASA Astrophysics Data System (ADS)

Koga, R.; Tsuchiya, F.; Kagitani, M.; Sakanoi, T.; Yoneda, M.; Yoshikawa, I.; Yoshioka, K.; Murakami, G.; Yamazaki, A.; Kimura, T.; Smith, H. T.

2017-12-01

We report the spatial distributions of oxygen neural cloud surrounding Jupiter's moon Io and along Io's orbit observed by the HISAKI satellite. Atomic oxygen and sulfur in Io's atmosphere escape from the exobase and move to corona (< 5.8 Io radii, the boundary where Jupiter's gravity begins to dominate) and neutral clouds (> 5.8 Io radii) mainly due to atmospheric sputtering. Io plasma torus is formed by ionization of these atoms by electron impact and charge exchange processes. It is essential to examine the dominant source of Io plasma torus, particularly in the vicinity of Io (<5.8 Io radii; atmosphere and corona) or the region away from Io (>5.8 Io radii; extended neutral clouds). The spatial distribution of oxygen and sulfur neutral clouds is important to understand the source. The extreme ultraviolet spectrometer called EXCEED (Extreme Ultraviolet Spectroscope for Exospheric Dynamics) installed on the Hisaki satellite observed Io plasma torus continuously in 2014-2015, and we carried out the monitoring of the distribution of atomic oxygen emission at 130.4 nm. The emission averaged over the distance range of 4.5-6.5 Jovian radii on the dawn and dusk sides strongly depends on the Io phase angle (IPA), and has a emission peak between IPA of 60-90 degrees on the dawn side, and between 240-270 degrees on the dusk side, respectively. It also shows the asymmetry with respect to Io's position: the intensity averaged for IPA 60-90 degrees (13.3 Rayleighs (R)) is 1.2 times greater than that for IPA 90-120 degrees (11.1 R) on the dawn side. The similar tendency is found on the dusk side. Weak atomic oxygen emission (4 R) uniformly distributes in every IPA. We also examined the radial distribution of the oxygen neutral cloud during the same period and found the emission peak near Io's orbit with decreasing the intensity toward 8.0 Jupiter radii. The results show the high density component of the oxygen neutral cloud is concentrated around Io and extends mainly toward leading side of Io. In addition, the low density neutrals uniformly exist along Io's orbit. Both components extend radially outward up to 8 Jovian radii with decreasing the density. In the presentation, we give the estimation of spatial distribution of oxygen neutral density and the oxygen ion source rate in the Io plasma torus.

A Smartphone Client-Server Teleradiology System for Primary Diagnosis of Acute Stroke

PubMed Central

2011-01-01

Background Recent advances in the treatment of acute ischemic stroke have made rapid acquisition, visualization, and interpretation of images a key factor for positive patient outcomes. We have developed a new teleradiology system based on a client-server architecture that enables rapid access to interactive advanced 2-D and 3-D visualization on a current generation smartphone device (Apple iPhone or iPod Touch, or an Android phone) without requiring patient image data to be stored on the device. Instead, a server loads and renders the patient images, then transmits a rendered frame to the remote device. Objective Our objective was to determine if a new smartphone client-server teleradiology system is capable of providing accuracies and interpretation times sufficient for diagnosis of acute stroke. Methods This was a retrospective study. We obtained 120 recent consecutive noncontrast computed tomography (NCCT) brain scans and 70 computed tomography angiogram (CTA) head scans from the Calgary Stroke Program database. Scans were read by two neuroradiologists, one on a medical diagnostic workstation and an iPod or iPhone (hereafter referred to as an iOS device) and the other only on an iOS device. NCCT brain scans were evaluated for early signs of infarction, which includes early parenchymal ischemic changes and dense vessel sign, and to exclude acute intraparenchymal hemorrhage and stroke mimics. CTA brain scans were evaluated for any intracranial vessel occlusion. The interpretations made on an iOS device were compared with those made at a workstation. The total interpretation times were recorded for both platforms. Interrater agreement was assessed. True positives, true negatives, false positives, and false negatives were obtained, and sensitivity, specificity, and accuracy of detecting the abnormalities on the iOS device were computed. Results The sensitivity, specificity, and accuracy of detecting intraparenchymal hemorrhage were 100% using the iOS device with a perfect interrater agreement (kappa = 1). The sensitivity, specificity, and accuracy of detecting acute parenchymal ischemic change were 94.1%, 100%, and 98.09% respectively for reader 1 and 97.05%, 100%, and 99.04% for reader 2 with nearly perfect interrater agreement (kappa = .8). The sensitivity, specificity, and accuracy of detecting dense vessel sign were 100%, 95.4%, and 96.19% respectively for reader 1 and 72.2%, 100%, and 95.23% for reader 2 using the iOS device with a good interrater agreement (kappa = .69). The sensitivity, specificity, and accuracy of detecting vessel occlusion on CT angiography scans were 94.4%, 100%, and 98.46% respectively for both readers using the iOS device, with perfect interrater agreement (kappa = 1). No significant difference (P < .05) was noted in the interpretation time between the workstation and iOS device. Conclusion The smartphone client-server teleradiology system appears promising and may have the potential to allow urgent management decisions in acute stroke. However, this study was retrospective, involved relatively few patient studies, and only two readers. Generalizing conclusions about its clinical utility, especially in other diagnostic use cases, should not be made until additional studies are performed. PMID:21550961

A smartphone client-server teleradiology system for primary diagnosis of acute stroke.

PubMed

Mitchell, J Ross; Sharma, Pranshu; Modi, Jayesh; Simpson, Mark; Thomas, Monroe; Hill, Michael D; Goyal, Mayank

2011-05-06

Recent advances in the treatment of acute ischemic stroke have made rapid acquisition, visualization, and interpretation of images a key factor for positive patient outcomes. We have developed a new teleradiology system based on a client-server architecture that enables rapid access to interactive advanced 2-D and 3-D visualization on a current generation smartphone device (Apple iPhone or iPod Touch, or an Android phone) without requiring patient image data to be stored on the device. Instead, a server loads and renders the patient images, then transmits a rendered frame to the remote device. Our objective was to determine if a new smartphone client-server teleradiology system is capable of providing accuracies and interpretation times sufficient for diagnosis of acute stroke. This was a retrospective study. We obtained 120 recent consecutive noncontrast computed tomography (NCCT) brain scans and 70 computed tomography angiogram (CTA) head scans from the Calgary Stroke Program database. Scans were read by two neuroradiologists, one on a medical diagnostic workstation and an iPod or iPhone (hereafter referred to as an iOS device) and the other only on an iOS device. NCCT brain scans were evaluated for early signs of infarction, which includes early parenchymal ischemic changes and dense vessel sign, and to exclude acute intraparenchymal hemorrhage and stroke mimics. CTA brain scans were evaluated for any intracranial vessel occlusion. The interpretations made on an iOS device were compared with those made at a workstation. The total interpretation times were recorded for both platforms. Interrater agreement was assessed. True positives, true negatives, false positives, and false negatives were obtained, and sensitivity, specificity, and accuracy of detecting the abnormalities on the iOS device were computed. The sensitivity, specificity, and accuracy of detecting intraparenchymal hemorrhage were 100% using the iOS device with a perfect interrater agreement (kappa=1). The sensitivity, specificity, and accuracy of detecting acute parenchymal ischemic change were 94.1%, 100%, and 98.09% respectively for reader 1 and 97.05%, 100%, and 99.04% for reader 2 with nearly perfect interrater agreement (kappa=.8). The sensitivity, specificity, and accuracy of detecting dense vessel sign were 100%, 95.4%, and 96.19% respectively for reader 1 and 72.2%, 100%, and 95.23% for reader 2 using the iOS device with a good interrater agreement (kappa=.69). The sensitivity, specificity, and accuracy of detecting vessel occlusion on CT angiography scans were 94.4%, 100%, and 98.46% respectively for both readers using the iOS device, with perfect interrater agreement (kappa=1). No significant difference (P<.05) was noted in the interpretation time between the workstation and iOS device. The smartphone client-server teleradiology system appears promising and may have the potential to allow urgent management decisions in acute stroke. However, this study was retrospective, involved relatively few patient studies, and only two readers. Generalizing conclusions about its clinical utility, especially in other diagnostic use cases, should not be made until additional studies are performed. ©J Ross Mitchell, Pranshu Sharma, Jayesh Modi, Mark Simpson, Monroe Thomas, Michael D. Hill, Mayank Goyal.

Optimized ECC Implementation for Secure Communication between Heterogeneous IoT Devices.

PubMed

Marin, Leandro; Pawlowski, Marcin Piotr; Jara, Antonio

2015-08-28

The Internet of Things is integrating information systems, places, users and billions of constrained devices into one global network. This network requires secure and private means of communications. The building blocks of the Internet of Things are devices manufactured by various producers and are designed to fulfil different needs. There would be no common hardware platform that could be applied in every scenario. In such a heterogeneous environment, there is a strong need for the optimization of interoperable security. We present optimized elliptic curve Cryptography algorithms that address the security issues in the heterogeneous IoT networks. We have combined cryptographic algorithms for the NXP/Jennic 5148- and MSP430-based IoT devices and used them to created novel key negotiation protocol.

On the location of the Io plasma torus: Voyager 1 observations

NASA Astrophysics Data System (ADS)

Volwerk, Martin

2018-06-01

The Voyager 1 outbound ultraviolet observations of the Io plasma torus are used to determine the location of the ansae, to obtain a third viewing angle of this structure in the Jovian magnetosphere. At an angle of -114° with respect to the Sun-Jupiter line, or a Jovian local time of 04:30 LT, the Voyager 1 data deliver a distance of 5.74±0.10 RJ for the approaching and 5.83±0.15 RJ for the receding ansa. Various periodicities in the radial distance, brightness and width of the ansae are seen with respect to system III longitude and Io phase angle. The torus ribbon feature does not appear in all ansa scans.

A real-time diagnostic and performance monitor for UNIX. M.S. Thesis

NASA Technical Reports Server (NTRS)

Dong, Hongchao

1992-01-01

There are now over one million UNIX sites and the pace at which new installations are added is steadily increasing. Along with this increase, comes a need to develop simple efficient, effective and adaptable ways of simultaneously collecting real-time diagnostic and performance data. This need exists because distributed systems can give rise to complex failure situations that are often un-identifiable with single-machine diagnostic software. The simultaneous collection of error and performance data is also important for research in failure prediction and error/performance studies. This paper introduces a portable method to concurrently collect real-time diagnostic and performance data on a distributed UNIX system. The combined diagnostic/performance data collection is implemented on a distributed multi-computer system using SUN4's as servers. The approach uses existing UNIX system facilities to gather system dependability information such as error and crash reports. In addition, performance data such as CPU utilization, disk usage, I/O transfer rate and network contention is also collected. In the future, the collected data will be used to identify dependability bottlenecks and to analyze the impact of failures on system performance.

Spatiotemporal Access Model Based on Reputation for the Sensing Layer of the IoT

PubMed Central

Guo, Yunchuan; Yin, Lihua; Li, Chao

2014-01-01

Access control is a key technology in providing security in the Internet of Things (IoT). The mainstream security approach proposed for the sensing layer of the IoT concentrates only on authentication while ignoring the more general models. Unreliable communications and resource constraints make the traditional access control techniques barely meet the requirements of the sensing layer of the IoT. In this paper, we propose a model that combines space and time with reputation to control access to the information within the sensing layer of the IoT. This model is called spatiotemporal access control based on reputation (STRAC). STRAC uses a lattice-based approach to decrease the size of policy bases. To solve the problem caused by unreliable communications, we propose both nondeterministic authorizations and stochastic authorizations. To more precisely manage the reputation of nodes, we propose two new mechanisms to update the reputation of nodes. These new approaches are the authority-based update mechanism (AUM) and the election-based update mechanism (EUM). We show how the model checker UPPAAL can be used to analyze the spatiotemporal access control model of an application. Finally, we also implement a prototype system to demonstrate the efficiency of our model. PMID:25177731

Paterae on Io: Volcanic Activity Observed by Galileo's NIMS and SSI

NASA Technical Reports Server (NTRS)

Lopes, Rosaly; Kamp, Lucas; Smythe, W. D.; Carlson, R.; Radebaugh, Jani; Gregg, Tracy K.

2003-01-01

Paterae are the most ubiquitous volcanic construct on Io s surface. Paterae are irregular craters, or complex craters with scalloped edges, interpreted as calderas or pit craters. Data from Galileo has shown that the activity of Ionian paterae is often confined to its interior and that generally lava flows are not seen spilling out over the edges. We use observations from Galileo s Near-Infrared Mapping Spectrometer (NIMS) to study the thermal emission from several Ionian paterae and compare them with images in visible wavelengths obtained by Galileo s Solid State Imaging System (SSI). Galileo s close fly-bys of Io from 1999 to 2001 have allowed NIMS to image the paterae at high spatial resolution (1-30 km pixel). At these scales, several of these features reveal greater thermal emission around the edges, which can be explained as the crust of a lava lake breaking up against the paterae walls. Comparisons with imaging data show that lower albedo areas (which are indicative of young lavas) coincide with higher thermal emission areas on NIMS data. Other paterae, however, show thermal emission and features in the visible that are more consistent with lava flows over a solid patera floor. Identifying eruption styles on Io is important for constraining eruption and interior models on Io.

Precision Agriculture Design Method Using a Distributed Computing Architecture on Internet of Things Context.

PubMed

Ferrández-Pastor, Francisco Javier; García-Chamizo, Juan Manuel; Nieto-Hidalgo, Mario; Mora-Martínez, José

2018-05-28

The Internet of Things (IoT) has opened productive ways to cultivate soil with the use of low-cost hardware (sensors/actuators) and communication (Internet) technologies. Remote equipment and crop monitoring, predictive analytic, weather forecasting for crops or smart logistics and warehousing are some examples of these new opportunities. Nevertheless, farmers are agriculture experts but, usually, do not have experience in IoT applications. Users who use IoT applications must participate in its design, improving the integration and use. In this work, different industrial agricultural facilities are analysed with farmers and growers to design new functionalities based on IoT paradigms deployment. User-centred design model is used to obtain knowledge and experience in the process of introducing technology in agricultural applications. Internet of things paradigms are used as resources to facilitate the decision making. IoT architecture, operating rules and smart processes are implemented using a distributed model based on edge and fog computing paradigms. A communication architecture is proposed using these technologies. The aim is to help farmers to develop smart systems both, in current and new facilities. Different decision trees to automate the installation, designed by the farmer, can be easily deployed using the method proposed in this document.

Interplanetary mission design techniques for flagship-class missions

NASA Astrophysics Data System (ADS)

Kloster, Kevin W.

Trajectory design, given the current level of propulsive technology, requires knowledge of orbital mechanics, computational resources, extensive use of tools such as gravity-assist and V infinity leveraging, as well as insight and finesse. Designing missions that deliver a capable science package to a celestial body of interest that are robust and affordable is a difficult task. Techniques are presented here that assist the mission designer in constructing trajectories for flagship-class missions in the outer Solar System. These techniques are applied in this work to spacecraft that are currently in flight or in the planning stages. By escaping the Saturnian system, the Cassini spacecraft can reach other destinations in the Solar System while satisfying planetary quarantine. The patched-conic method was used to search for trajectories that depart Saturn via gravity assist at Titan. Trajectories were found that fly by Jupiter to reach Uranus or Neptune, capture at Jupiter or Neptune, escape the Solar System, fly by Uranus during its 2049 equinox, or encounter Centaurs. A "grand tour," which visits Jupiter, Uranus, and Neptune, departs Saturn in 2014. New tools were built to search for encounters with Centaurs, small Solar System bodies between the orbits of Jupiter and Neptune, and to minimize the DeltaV to target these encounters. Cassini could reach Chiron, the first-discovered Centaur, in 10.5 years after a 2022 Saturn departure. For a Europa Orbiter mission, the strategy for designing Jovian System tours that include Io flybys differs significantly from schemes developed for previous versions of the mission. Assuming that the closest approach distance of the incoming hyperbola at Jupiter is below the orbit of Io, then an Io gravity assist gives the greatest energy pump-down for the least decrease in perijove radius. Using Io to help capture the spacecraft can increase the savings in Jupiter orbit insertion DeltaV over a Ganymede-aided capture. The tour design is guided by Tisserand graphs overlaid with a simple and accurate radiation model so that tours including Io flybys can maintain an acceptable radiation dosage. While Io flybys increase the duration of tours that are ultimately bound for Europa, they offer DeltaV savings and greater scientific return, including the possibility of flying through the plume of one of Io's volcanoes. Different combinations of interplanetary trajectories and are considered with a focus on options that could enable flagship-class missions to Uranus. A patched-conic method is used to identify trajectories to Uranus with launch dates between 2015 and 2050. Flight time is constrained to be less than 14 years. A graphical technique is introduced to identify the most efficient launch opportunities and gravity-assist paths to Uranus. Several trajectories emerge as attractive options including classical paths such as Venus-Earth-Earth-Jupiter, with launch V1 as low as 3.6 km/s. A baseline DeltaV cost is established for capture at Uranus via chemical propulsion. Ballistic reduction of orbital inclination using flybys of the satellites of Uranus is investigated; Oberon is shown to have greater inclination change capability than Titania despite Oberon being less massive.

Modeling Ultraviolet Emissions Near Io

NASA Technical Reports Server (NTRS)

Linker, Jon A.

2000-01-01

In this report, we describe work awarded to Science Applications International Corporation, for the period 6/l/99 to 5/31/00. During this time period, we have investigated the interaction of Io, Jupiter's innermost Galilean satellite, with the Io plasma torus, and the role this interaction plays in producing ultraviolet (UV) emissions from neutral oxygen and sulfur. Io, the innermost of Jupiter's Galilean satellites, plays a unique role in the jovian magnetosphere. Neutral material that escapes from Io is ionized to form the lo torus, a dense, heavy-ion plasma that corotates with Jupiter and interacts with Io. Io supplies not only the torus, but is a major source of plasma for the entire magnetosphere. Ionization and charge-exchange of neutrals near lo strongly influences the plasma interaction, and Io's neutral atmosphere plays an important role in the generation of currents that couple Io to Jupiter. There have been no in situ measurements of the neutral density near Io, but remote observations of neutrals near lo have been performed for many years. Recent observations from the Hubble Space Telescope (HST) have shown detailed structure in UV emissions from neutral species near Io. Electron-impact of the neutrals by the Io torus plasma is the primary mechanism responsible for exciting these emissions. Previously, we have modeled the Io plasma environment using three-dimensional magnetohydrodynamic (MHD) simulations, and we have shown that the interaction between Io and the plasma torus plays an important role in producing the morphology of the observed emissions. In the past year, we have extended these studies to use both UV observations and Galileo particle and field measurements to investigate the Io interaction.

Io. [history of studies and current level of understanding of this satellite

NASA Technical Reports Server (NTRS)

Nash, Douglas B.; Yoder, Charles F.; Carr, Michael H.; Gradie, Jonathan; Hunten, Donald M.

1986-01-01

The present work reviews the history of Io studies and describes the current level of understanding of Io's physics, chemistry, geology, orbital dynamics, and geophysics. Consideration is given to the satellite's internal, superficial, atmospheric, plasma, and magnetospheric properties and how they interrelate. A pictorial map of Io's surface based on Voyager 1 and 2 images is presented. It is found that Io's surface color and spectra are dominated by sulfur compounds which may include various sulfur allotropes. Volcanic processes yielding three kinds of surface features (vent regions, plains, and mountains) dominate Io's surface geology. The Io plasma torus corotates with Jupiter's magnetic field in the plane of Jupiter's centrifugal equator centered at Io's orbital radius.

Two Barium Gold Iodates: Syntheses, Structures, and Properties of Polar BaAu(IO3)5 and Nonpolar HBa4Au(IO3)12 Materials.

PubMed

Yang, Bing-Ping; Hu, Chun-Li; Mao, Fei-Fei; Xu, Xiang; Mao, Jiang-Gao

2017-06-19

Two new barium gold iodates, namely, BaAu(IO 3 ) 5 and HBa 4 Au(IO 3 ) 12 , have been prepared. BaAu(IO 3 ) 5 crystallizes in the polar space group Pca2 1 , whereas HBa 4 Au(IO 3 ) 12 crystallizes in the centrosymmetric space group P2 1 /c. BaAu(IO 3 ) 5 consists of unique polar [Au(IO 3 ) 4 ] - anions whose four iodate groups are located at both sides of the AuO 4 plane and the polarity points in the [001̅] direction. BaAu(IO 3 ) 5 displays strong second-harmonic-generation (SHG) effects about 0.6KTiOPO 4 (KTP) and is phase-matchable. Thermal properties, optical spectra analyses, and theoretical calculations are also reported.

Efficacy of intraosseous injections of anesthetic in children and adolescents.

PubMed

Sixou, Jean-Louis; Barbosa-Rogier, Maria Elizena

2008-08-01

The goal of this study was to determine the efficacy of the intraosseous (IO) injections of anesthetic as a primary technique in children and adolescents. A cohort of 181 children and adolescents underwent a total of 225 sessions of IO injections of 4% articaine with 1:200,000 epinephrine using the Quick Sleeper 2 system. Evaluations could be performed in 215 sessions (171 patients, 247 teeth), yielding success rates of 91.2% (sessions) and 91.9% (teeth). The success rate was 95% (133 of 140) for temporary teeth (endodontics 96.6%, restorations 100%, extractions 88%) and 87.9% (94 of 107) for permanent teeth (endodontics 92.3%, restorations 89.9%, extractions 75%). No difference was noted in terms of age (P > .05). No cases of biting of mucosa or postinjection pain were noted. The IO injection of anesthetic using a computer-controlled osseous perforation and delivery system can be considered as a good alternative or supplement to classic infiltration techniques in children and adolescents.

Applying deep neural networks to HEP job classification

NASA Astrophysics Data System (ADS)

Wang, L.; Shi, J.; Yan, X.

2015-12-01

The cluster of IHEP computing center is a middle-sized computing system which provides 10 thousands CPU cores, 5 PB disk storage, and 40 GB/s IO throughput. Its 1000+ users come from a variety of HEP experiments. In such a system, job classification is an indispensable task. Although experienced administrator can classify a HEP job by its IO pattern, it is unpractical to classify millions of jobs manually. We present how to solve this problem with deep neural networks in a supervised learning way. Firstly, we built a training data set of 320K samples by an IO pattern collection agent and a semi-automatic process of sample labelling. Then we implemented and trained DNNs models with Torch. During the process of model training, several meta-parameters was tuned with cross-validations. Test results show that a 5- hidden-layer DNNs model achieves 96% precision on the classification task. By comparison, it outperforms a linear model by 8% precision.

AP-IO: asynchronous pipeline I/O for hiding periodic output cost in CFD simulation.

PubMed

Xiaoguang, Ren; Xinhai, Xu

2014-01-01

Computational fluid dynamics (CFD) simulation often needs to periodically output intermediate results to files in the form of snapshots for visualization or restart, which seriously impacts the performance. In this paper, we present asynchronous pipeline I/O (AP-IO) optimization scheme for the periodically snapshot output on the basis of asynchronous I/O and CFD application characteristics. In AP-IO, dedicated background I/O processes or threads are in charge of handling the file write in pipeline mode, therefore the write overhead can be hidden with more calculation than classic asynchronous I/O. We design the framework of AP-IO and implement it in OpenFOAM, providing CFD users with a user-friendly interface. Experimental results on the Tianhe-2 supercomputer demonstrate that AP-IO can achieve a good optimization effect for the periodical snapshot output in CFD application, and the effect is especially better for massively parallel CFD simulations, which can reduce the total execution time up to about 40%.

AP-IO: Asynchronous Pipeline I/O for Hiding Periodic Output Cost in CFD Simulation

PubMed Central

Xiaoguang, Ren; Xinhai, Xu

2014-01-01

Computational fluid dynamics (CFD) simulation often needs to periodically output intermediate results to files in the form of snapshots for visualization or restart, which seriously impacts the performance. In this paper, we present asynchronous pipeline I/O (AP-IO) optimization scheme for the periodically snapshot output on the basis of asynchronous I/O and CFD application characteristics. In AP-IO, dedicated background I/O processes or threads are in charge of handling the file write in pipeline mode, therefore the write overhead can be hidden with more calculation than classic asynchronous I/O. We design the framework of AP-IO and implement it in OpenFOAM, providing CFD users with a user-friendly interface. Experimental results on the Tianhe-2 supercomputer demonstrate that AP-IO can achieve a good optimization effect for the periodical snapshot output in CFD application, and the effect is especially better for massively parallel CFD simulations, which can reduce the total execution time up to about 40%. PMID:24955390

Juno-UVS observation of the Io footprint: Influence of Io's local environment and passage into eclipse on the strength of the interaction

NASA Astrophysics Data System (ADS)

Hue, V.; Gladstone, R.; Greathouse, T. K.; Versteeg, M.; Bonfond, B.; Saur, J.; Davis, M. W.; Roth, L.; Grodent, D. C.; Gerard, J. C. M. C.; Kammer, J.; Bolton, S. J.; Levin, S.; Connerney, J. E. P.

2017-12-01

The Juno mission offers an unprecedented opportunity to study Jupiter, from its internal structure to its magnetospheric environment. Juno-UVS is a UV spectrograph with a bandpass of 70<λ<205 nm, built to characterize Jupiter's UV emissions and provide remote sensing capacities for the onboard fields and particle instruments (MAG, Waves, JADE and JEDI). Juno's orbit allows observing Jupiter from a unique vantage point above the poles. In particular, UVS has observed the instantaneous Io footprint and extended tail as Io enters into eclipse. This observation may better constrain whether the atmosphere of Io is sustained via volcanic activity or sublimation. Among other processes, the modulation of Io's footprint brightness correlates to the strength of the interaction between the Io plasma torus and its ionosphere, which, in turn, is likely to be affected by the atmospheric collapse. UVS observed the Io footprint during two eclipses that occurred on PJ1 and PJ3, and one additional eclipse observation is planned during PJ9 (24 Oct. 2017). We present how the electrodynamic coupling between Io and Jupiter is influenced by changes in Io's local environment, e.g. Io's passage in and out of eclipse and Io's traverse of the magnetodisc plasma sheet.

Feasibility of employing a smartphone as the payload in a photogrammetric UAV system

NASA Astrophysics Data System (ADS)

Kim, Jinsoo; Lee, Seongkyu; Ahn, Hoyong; Seo, Dongju; Park, Soyoung; Choi, Chuluong

2013-05-01

Smartphones can be operated in a 3G network environment at any time or location, and they also cost less than existing photogrammetric UAV systems, providing high-resolution images and 3D location and attitude data from a variety of built-in sensors. This study aims to assess the feasibility of using a smartphone as the payload for a photogrammetric UAV system. To carry out the assessment, a smartphone-based photogrammetric UAV system was developed and utilized to obtain image, location, and attitude data under both static and dynamic conditions. The accuracy of the location and attitude data obtained and sent by this system was then evaluated. The smartphone images were converted into ortho-images via image triangulation, which was carried out both with and without consideration of the interior orientation (IO) parameters determined by camera calibration. In the static experiment, when the IO parameters were taken into account, the triangulation results were less than 1.28 pixels (RMSE) for all smartphone types, an improvement of at least 47% compared with the case when IO parameters were not taken into account. In the dynamic experiment, on the other hand, the accuracy of smartphone image triangulation was not significantly improved by considering IO parameters. This was because the electronic rolling shutter within the complementary metal-oxide semiconductor (CMOS) sensor built into the smartphone and the actuator for the voice coil motor (VCM)-type auto-focusing affected by the vibration and the speed of the UAV, which is likely to have a negative effect on image-based digital elevation model (DEM) generation. However, considering that these results were obtained using a single smartphone, this suggests that a smartphone is not only feasible as the payload for a photogrammetric UAV system but it may also play a useful role when installed in existing UAV systems.

Filling the Information Void: Adapting the Information Operation (IO) Message in Post-Hostility Iraq

DTIC Science & Technology

2005-05-26

more elaborate, with Pizza Huts and Burger Kings, and so large that one, called Anaconda, has nine bus routes to move the troops around inside the...circulation of 50,000 weekly.71 Based on American principles of freedom of speech and the value of debate, one may conclude that the proliferation of news...democratic values . According to the World Press Freedom Committee, “as always, the proper answer to bad speech is more speech, not the silencing of

POSIX and Object Distributed Storage Systems Performance Comparison Studies With Real-Life Scenarios in an Experimental Data Taking Context Leveraging OpenStack Swift & Ceph

NASA Astrophysics Data System (ADS)

Poat, M. D.; Lauret, J.; Betts, W.

2015-12-01

The STAR online computing infrastructure has become an intensive dynamic system used for first-hand data collection and analysis resulting in a dense collection of data output. As we have transitioned to our current state, inefficient, limited storage systems have become an impediment to fast feedback to online shift crews. Motivation for a centrally accessible, scalable and redundant distributed storage system had become a necessity in this environment. OpenStack Swift Object Storage and Ceph Object Storage are two eye-opening technologies as community use and development have led to success elsewhere. In this contribution, OpenStack Swift and Ceph have been put to the test with single and parallel I/O tests, emulating real world scenarios for data processing and workflows. The Ceph file system storage, offering a POSIX compliant file system mounted similarly to an NFS share was of particular interest as it aligned with our requirements and was retained as our solution. I/O performance tests were run against the Ceph POSIX file system and have presented surprising results indicating true potential for fast I/O and reliability. STAR'S online compute farm historical use has been for job submission and first hand data analysis. The goal of reusing the online compute farm to maintain a storage cluster and job submission will be an efficient use of the current infrastructure.

Status of Europe's contribution to the ITER EC system

NASA Astrophysics Data System (ADS)

Albajar, F.; Aiello, G.; Alberti, S.; Arnold, F.; Avramidis, K.; Bader, M.; Batista, R.; Bertizzolo, R.; Bonicelli, T.; Braunmueller, F.; Brescan, C.; Bruschi, A.; von Burg, B.; Camino, K.; Carannante, G.; Casarin, V.; Castillo, A.; Cauvard, F.; Cavalieri, C.; Cavinato, M.; Chavan, R.; Chelis, J.; Cismondi, F.; Combescure, D.; Darbos, C.; Farina, D.; Fasel, D.; Figini, L.; Gagliardi, M.; Gandini, F.; Gantenbein, G.; Gassmann, T.; Gessner, R.; Goodman, T. P.; Gracia, V.; Grossetti, G.; Heemskerk, C.; Henderson, M.; Hermann, V.; Hogge, J. P.; Illy, S.; Ioannidis, Z.; Jelonnek, J.; Jin, J.; Kasparek, W.; Koning, J.; Krause, A. S.; Landis, J. D.; Latsas, G.; Li, F.; Mazzocchi, F.; Meier, A.; Moro, A.; Nousiainen, R.; Purohit, D.; Nowak, S.; Omori, T.; van Oosterhout, J.; Pacheco, J.; Pagonakis, I.; Platania, P.; Poli, E.; Preis, A. K.; Ronden, D.; Rozier, Y.; Rzesnicki, T.; Saibene, G.; Sanchez, F.; Sartori, F.; Sauter, O.; Scherer, T.; Schlatter, C.; Schreck, S.; Serikov, A.; Siravo, U.; Sozzi, C.; Spaeh, P.; Spichiger, A.; Strauss, D.; Takahashi, K.; Thumm, M.; Tigelis, I.; Vaccaro, A.; Vomvoridis, J.; Tran, M. Q.; Weinhorst, B.

2015-03-01

The electron cyclotron (EC) system of ITER for the initial configuration is designed to provide 20MW of RF power into the plasma during 3600s and a duty cycle of up to 25% for heating and (co and counter) non-inductive current drive, also used to control the MHD plasma instabilities. The EC system is being procured by 5 domestic agencies plus the ITER Organization (IO). F4E has the largest fraction of the EC procurements, which includes 8 high voltage power supplies (HVPS), 6 gyrotrons, the ex-vessel waveguides (includes isolation valves and diamond windows) for all launchers, 4 upper launchers and the main control system. F4E is working with IO to improve the overall design of the EC system by integrating consolidated technological advances, simplifying the interfaces, and doing global engineering analysis and assessments of EC heating and current drive physics and technology capabilities. Examples are the optimization of the HVPS and gyrotron requirements and performance relative to power modulation for MHD control, common qualification programs for diamond window procurements, assessment of the EC grounding system, and the optimization of the launcher steering angles for improved EC access. Here we provide an update on the status of Europe's contribution to the ITER EC system, and a summary of the global activities underway by F4E in collaboration with IO for the optimization of the subsystems.

Io: Intensive Heating and Degassing, Rising and Falling Stripes In Crossing Wavy Patterns Do Not Require Molten Interior

NASA Astrophysics Data System (ADS)

Kochemasov, G.

"Orbits make structures". This fundamental concept unfolded in four theorems of the wave planetary tectonics [1] simply means that Keplerian non-circular orbits imply inertia forces which make planetary bodies oscillate and produce structures. Many examples of regular wave woven structures on surfaces of planets (and asteroids and comets - Borrelli !) and satellites prove it. Theorem 3 ("Celestial bodies are granular "[1]) connects a size of tectonic granulation with an orbital frequency. But what to do with satellites having more orbits than planets ? Here acts the wave modulation pro- cess. A low frequency modulates a high frequency producing lower and higher side frequencies. Actually we explained ubiquitous tectonic dichotomy (Theorem 1, [1]) by modulation of all frequencies in the Solar System (SS) by the very low galactic frequency of the SS. In this case we considered the lower side frequency. But at the opposite side there are the higher side frequencies which fall into a range of radio- and microwave frequencies so typical for bodies of the SS [2]. These higher side frequen- cies depend on a body's radius and its orbital frequency. For example, the Io orbital frequency is modulated by the Jupiter orbital frequency and by the galactic orbital frequency of the SS (1/12 years and ~1/200 000 000 years). The Io circumsolar fre- quency (together with Jupiter) is also modulated by the galactic frequency. So, there are three higher side frequencies for Io to which correspond three wavelengths: 4.62 km (Io orbits Jupiter),68 cm (Io's circumsolar orbit in the galactic orbit), 0.276 mm (Io's circumjovian orbit in the galactic orbit). For smaller and faster Amalthea these wave oscillations are: 93.2 m - 4.88 cm - 0.0056 mm. So "microwave stove" heating might be an appreciable source of heating for Io as well as for Amalthea (also anoma- lously heated body) [3]. Very variable Io's surface and very short wave (upto 10 m) crossing patterns are already observed. Io's 5 micron outbursts are reported [4]. They could be produced by the heated Io's body. Surprisingly, 5 micron (0.0056 mm) oscil- 1 lations we calculate for Amalthea. The 2002 y. meeting "Galileo" with Amalthea will bring additional information. References: [1] Kochemasov G.G.(1999) Theorems of wave planetary tectonics // Geophys. Res. Abstr., v.1, #3, 700; [2] Kochemasov G.G. (2001) Vernadsky-Brown 34th microsymp. Topics in comparative planetology. Abstr., Moscow, (CD-ROM); [3] Kochemasov G.G. (1997) Ibid. 26th, 58-59; [4]Sinton W.M. (1980) Astrophys.J., v. 235, #1, 149-151. 2

Two Moons Meet over Jupiter

NASA Technical Reports Server (NTRS)

2007-01-01

This beautiful image of the crescents of volcanic Io and more sedate Europa was snapped by New Horizons' color Multispectral Visual Imaging Camera (MVIC) at 10:34 UT on March 2, 2007, about two days after New Horizons made its closest approach to Jupiter.

The picture was one of a handful of the Jupiter system that New Horizons took primarily for their artistic, rather than scientific value. This particular scene was suggested by space enthusiast Richard Hendricks of Austin, Texas, in response to an Internet request by New Horizons scientists for evocative, artistic imaging opportunities at Jupiter.

This image was taken from a range of 4.6 million kilometers (2.8 million miles) from Io and 3.8 million kilometers (2.4 million miles) from Europa. Although the moons appear close in this view, a gulf of 790,000 kilometers (490,000 miles) separates them. The night side of Io is illuminated here by light reflected from Jupiter, which is out of the frame to the right. Europa's night side is completely dark, in contrast to Io, because that side of Europa faces away from Jupiter.

Here, Io steals the show with its beautiful display of volcanic activity. Three volcanic plumes are visible. Most conspicuous is the enormous 300-kilometer (190-mile) -high plume from the Tvashtar volcano at the 11 o'clock position on Io's disk. Two much smaller plumes are barely visible: one from the volcano Prometheus, at the 9 o'clock position on the edge of Io's disk, and one from the volcano Amirani, seen between Prometheus and Tvashtar along Io's terminator (the line dividing day and night). The plumes appear blue because of the scattering of light by tiny dust particles ejected by the volcanoes, similar to the blue appearance of smoke. In addition, the contrasting red glow of hot lava can be seen at the source of the Tvashtar plume.

The images are centered at 1 degree north, 60 degrees west on Io, and 0 degrees north, 149 degrees west on Europa. The color in this image was generated using individual MVIC images at wavelengths of 480, 620 and 850 nanometers. The human eye is sensitive to slightly shorter wavelengths, from 400 to 700 nanometers, and thus would see the scene slightly differently. For instance, while the eye would notice the difference between the yellow and reddish brown colors of Io's surface and the paler color of Europa, the two worlds appear very similar in color to MVIC's longer-wavelength vision. The night side of Io appears greenish compared to the day side, because methane in Jupiter's atmosphere absorbs 850-nanometer light and makes Jupiter-light green to MVIC's 'eyes.'

MVIC is a component of the Ralph imaging instrument.