Science.gov

Sample records for adaptive noise canceling

  1. Sub-band adaptive noise cancelling

    NASA Astrophysics Data System (ADS)

    Ryan, James G.; Goubran, Rafik A.

    The technique of using sub-band adaptive filters for acoustic noise suppression is examined. Simulation results are presented for experimental systems trained with white noise and colored noise for both decimated and non-decimated sub-band signals. To illustrate the usefulness of the sub-band approach for a real application, the full band and sub-band noise cancellers were applied to car data. Estimates of the input and output power spectra for the different cases are presented. It is shown that the full-band noise canceller is unable to attenuate the noise in the higher frequencies due to the low input signal power in this region. The sub-band decomposition of the input signal can significantly increase the rate as compared to a full-band implementation under certain conditions. This increase in convergence speed is manifested as an increased noise attenuation in those regions of the input spectrum with relatively low amounts of power. In addition, the sub-band processing is seen to eliminate the noise enhancement phenomenon found in acoustic noise cancellers for mobile telephony.

  2. Background Noise Reduction Using Adaptive Noise Cancellation Determined by the Cross-Correlation

    NASA Technical Reports Server (NTRS)

    Spalt, Taylor B.; Brooks, Thomas F.; Fuller, Christopher R.

    2012-01-01

    Background noise due to flow in wind tunnels contaminates desired data by decreasing the Signal-to-Noise Ratio. The use of Adaptive Noise Cancellation to remove background noise at measurement microphones is compromised when the reference sensor measures both background and desired noise. The technique proposed modifies the classical processing configuration based on the cross-correlation between the reference and primary microphone. Background noise attenuation is achieved using a cross-correlation sample width that encompasses only the background noise and a matched delay for the adaptive processing. A present limitation of the method is that a minimum time delay between the background noise and desired signal must exist in order for the correlated parts of the desired signal to be separated from the background noise in the crosscorrelation. A simulation yields primary signal recovery which can be predicted from the coherence of the background noise between the channels. Results are compared with two existing methods.

  3. Adaptive noise cancellation based on beehive pattern evolutionary digital filter

    NASA Astrophysics Data System (ADS)

    Zhou, Xiaojun; Shao, Yimin

    2014-01-01

    Evolutionary digital filtering (EDF) exhibits the advantage of avoiding the local optimum problem by using cloning and mating searching rules in an adaptive noise cancellation system. However, convergence performance is restricted by the large population of individuals and the low level of information communication among them. The special beehive structure enables the individuals on neighbour beehive nodes to communicate with each other and thus enhance the information spread and random search ability of the algorithm. By introducing the beehive pattern evolutionary rules into the original EDF, this paper proposes an improved beehive pattern evolutionary digital filter (BP-EDF) to overcome the defects of the original EDF. In the proposed algorithm, a new evolutionary rule which combines competing cloning, complete cloning and assistance mating methods is constructed to enable the individuals distributed on the beehive to communicate with their neighbours. Simulation results are used to demonstrate the improved performance of the proposed algorithm in terms of convergence speed to the global optimum compared with the original methods. Experimental results also verify the effectiveness of the proposed algorithm in extracting feature signals that are contaminated by significant amounts of noise during the fault diagnosis task.

  4. Comparative study of adaptive-noise-cancellation algorithms for intrusion detection systems

    SciTech Connect

    Claassen, J.P.; Patterson, M.M.

    1981-01-01

    Some intrusion detection systems are susceptible to nonstationary noise resulting in frequent nuisance alarms and poor detection when the noise is present. Adaptive inverse filtering for single channel systems and adaptive noise cancellation for two channel systems have both demonstrated good potential in removing correlated noise components prior detection. For such noise susceptible systems the suitability of a noise reduction algorithm must be established in a trade-off study weighing algorithm complexity against performance. The performance characteristics of several distinct classes of algorithms are established through comparative computer studies using real signals. The relative merits of the different algorithms are discussed in the light of the nature of intruder and noise signals.

  5. A Background Noise Reduction Technique Using Adaptive Noise Cancellation for Microphone Arrays

    NASA Technical Reports Server (NTRS)

    Spalt, Taylor B.; Fuller, Christopher R.; Brooks, Thomas F.; Humphreys, William M., Jr.; Brooks, Thomas F.

    2011-01-01

    Background noise in wind tunnel environments poses a challenge to acoustic measurements due to possible low or negative Signal to Noise Ratios (SNRs) present in the testing environment. This paper overviews the application of time domain Adaptive Noise Cancellation (ANC) to microphone array signals with an intended application of background noise reduction in wind tunnels. An experiment was conducted to simulate background noise from a wind tunnel circuit measured by an out-of-flow microphone array in the tunnel test section. A reference microphone was used to acquire a background noise signal which interfered with the desired primary noise source signal at the array. The technique s efficacy was investigated using frequency spectra from the array microphones, array beamforming of the point source region, and subsequent deconvolution using the Deconvolution Approach for the Mapping of Acoustic Sources (DAMAS) algorithm. Comparisons were made with the conventional techniques for improving SNR of spectral and Cross-Spectral Matrix subtraction. The method was seen to recover the primary signal level in SNRs as low as -29 dB and outperform the conventional methods. A second processing approach using the center array microphone as the noise reference was investigated for more general applicability of the ANC technique. It outperformed the conventional methods at the -29 dB SNR but yielded less accurate results when coherence over the array dropped. This approach could possibly improve conventional testing methodology but must be investigated further under more realistic testing conditions.

  6. Transform Domain Robust Variable Step Size Griffiths' Adaptive Algorithm for Noise Cancellation in ECG

    NASA Astrophysics Data System (ADS)

    Hegde, Veena; Deekshit, Ravishankar; Satyanarayana, P. S.

    2011-12-01

    The electrocardiogram (ECG) is widely used for diagnosis of heart diseases. Good quality of ECG is utilized by physicians for interpretation and identification of physiological and pathological phenomena. However, in real situations, ECG recordings are often corrupted by artifacts or noise. Noise severely limits the utility of the recorded ECG and thus needs to be removed, for better clinical evaluation. In the present paper a new noise cancellation technique is proposed for removal of random noise like muscle artifact from ECG signal. A transform domain robust variable step size Griffiths' LMS algorithm (TVGLMS) is proposed for noise cancellation. For the TVGLMS, the robust variable step size has been achieved by using the Griffiths' gradient which uses cross-correlation between the desired signal contaminated with observation or random noise and the input. The algorithm is discrete cosine transform (DCT) based and uses symmetric property of the signal to represent the signal in frequency domain with lesser number of frequency coefficients when compared to that of discrete Fourier transform (DFT). The algorithm is implemented for adaptive line enhancer (ALE) filter which extracts the ECG signal in a noisy environment using LMS filter adaptation. The proposed algorithm is found to have better convergence error/misadjustment when compared to that of ordinary transform domain LMS (TLMS) algorithm, both in the presence of white/colored observation noise. The reduction in convergence error achieved by the new algorithm with desired signal decomposition is found to be lower than that obtained without decomposition. The experimental results indicate that the proposed method is better than traditional adaptive filter using LMS algorithm in the aspects of retaining geometrical characteristics of ECG signal.

  7. Industrial wideband noise reduction for hearing aids using a headset with adaptive-feedback active noise cancellation.

    PubMed

    Lin, J H; Li, P C; Tang, S T; Liu, P T; Young, S T

    2005-11-01

    High-intensity noises are a health hazard for industrial workers, and hearing protection is necessary to prevent hearing loss. Passive methods, such as ear muffs, are ineffective against low-frequency noise. Moreover, many hearing-impaired workers must wear hearing aids to enable communication at their workplace, and such aids can amplify ambient noise. To overcome this problem, the present study developed a headset equipped with a digital signal processing system to implement adaptive-feedback active noise cancellation (AFANC) to reduce low-frequency noise. The proposed AFANC headset was effective against wideband industrial noise, with a maximum noise spectrum power reduction of 30 dB. Furthermore, when used with a hearing aid, it improved the speech signal-to-noise ratio by up to 14 dB. These results suggest that a headset with AFANC would be useful for hearing protection in workplaces with high levels of low-frequency industrial noise, especially for hearing-impaired workers. PMID:16594300

  8. Blood pressure measurement in noise intensive environments using adaptive interference cancellation.

    PubMed

    Pinto, Lisa; Dhanantwari, Amar; Wong, Winnie; Stergiopoulos, Stergios; Maris, Mike

    2002-05-01

    The traditional auscultatory technique and current methodologies for measuring human blood pressure are limited when used in situations where extreme vibration or acoustic noise is present. In this study, human subjects were used to establish the effectiveness of a novel adaptive blood pressure monitoring (ABPM) system in determining systolic-diastolic pressure in vibration and noise intense environments. To remove the effects of noise and vibration from the audible Korotkoff sounds, the proposed ABPM system employs two acoustic sensors in the pressure cuff. The primary acoustic sensor is placed on the brachial artery to record the Korotkoff sounds while the secondary acoustic sensor is placed away from the artery to record background noise and vibrations. The signals from the two acoustic sensors are provided to the input of an adaptive interference canceller to remove the noise effects in the signal of the primary acoustic sensor. In two phases of clinical testing, the ABPM system was first employed in a noiseless environment and then near and onboard search and rescue helicopters. The results from both phases deliver a successful demonstration of the ABPM system's capabilities to provide blood pressure estimates in noisy environments where the conventional auscultatory and other techniques have limited use.

  9. Adaptive HIFU noise cancellation for simultaneous therapy and imaging using an integrated HIFU/imaging transducer

    PubMed Central

    Jeong, Jong Seob; Cannata, Jonathan Matthew; Shung, K Kirk

    2010-01-01

    It was previously demonstrated that it is feasible to simultaneously perform ultrasound therapy and imaging of a coagulated lesion during treatment with an integrated transducer that is capable of high intensity focused ultrasound (HIFU) and B-mode ultrasound imaging. It was found that coded excitation and fixed notch filtering upon reception could significantly reduce interference caused by the therapeutic transducer. During HIFU sonication, the imaging signal generated with coded excitation and fixed notch filtering had a range side-lobe level of less than −40 dB, while traditional short-pulse excitation and fixed notch filtering produced a range side-lobe level of −20 dB. The shortcoming is, however, that relatively complicated electronics may be needed to utilize coded excitation in an array imaging system. It is for this reason that in this paper an adaptive noise canceling technique is proposed to improve image quality by minimizing not only the therapeutic interference, but also the remnant side-lobe ‘ripples’ when using the traditional short-pulse excitation. The performance of this technique was verified through simulation and experiments using a prototype integrated HIFU/imaging transducer. Although it is known that the remnant ripples are related to the notch attenuation value of the fixed notch filter, in reality, it is difficult to find the optimal notch attenuation value due to the change in targets or the media resulted from motion or different acoustic properties even during one sonication pulse. In contrast, the proposed adaptive noise canceling technique is capable of optimally minimizing both the therapeutic interference and residual ripples without such constraints. The prototype integrated HIFU/imaging transducer is composed of three rectangular elements. The 6 MHz center element is used for imaging and the outer two identical 4 MHz elements work together to transmit the HIFU beam. Two HIFU elements of 14.4 mm × 20.0 mm dimensions

  10. EEG/ERP adaptive noise canceller design with controlled search space (CSS) approach in cuckoo and other optimization algorithms.

    PubMed

    Ahirwal, M K; Kumar, Anil; Singh, G K

    2013-01-01

    This paper explores the migration of adaptive filtering with swarm intelligence/evolutionary techniques employed in the field of electroencephalogram/event-related potential noise cancellation or extraction. A new approach is proposed in the form of controlled search space to stabilize the randomness of swarm intelligence techniques especially for the EEG signal. Swarm-based algorithms such as Particles Swarm Optimization, Artificial Bee Colony, and Cuckoo Optimization Algorithm with their variants are implemented to design optimized adaptive noise canceler. The proposed controlled search space technique is tested on each of the swarm intelligence techniques and is found to be more accurate and powerful. Adaptive noise canceler with traditional algorithms such as least-mean-square, normalized least-mean-square, and recursive least-mean-square algorithms are also implemented to compare the results. ERP signals such as simulated visual evoked potential, real visual evoked potential, and real sensorimotor evoked potential are used, due to their physiological importance in various EEG studies. Average computational time and shape measures of evolutionary techniques are observed 8.21E-01 sec and 1.73E-01, respectively. Though, traditional algorithms take negligible time consumption, but are unable to offer good shape preservation of ERP, noticed as average computational time and shape measure difference, 1.41E-02 sec and 2.60E+00, respectively.

  11. A multichannel nonlinear adaptive noise canceller based on generalized FLANN for fetal ECG extraction

    NASA Astrophysics Data System (ADS)

    Ma, Yaping; Xiao, Yegui; Wei, Guo; Sun, Jinwei

    2016-01-01

    In this paper, a multichannel nonlinear adaptive noise canceller (ANC) based on the generalized functional link artificial neural network (FLANN, GFLANN) is proposed for fetal electrocardiogram (FECG) extraction. A FIR filter and a GFLANN are equipped in parallel in each reference channel to respectively approximate the linearity and nonlinearity between the maternal ECG (MECG) and the composite abdominal ECG (AECG). A fast scheme is also introduced to reduce the computational cost of the FLANN and the GFLANN. Two (2) sets of ECG time sequences, one synthetic and one real, are utilized to demonstrate the improved effectiveness of the proposed nonlinear ANC. The real dataset is derived from the Physionet non-invasive FECG database (PNIFECGDB) including 55 multichannel recordings taken from a pregnant woman. It contains two subdatasets that consist of 14 and 8 recordings, respectively, with each recording being 90 s long. Simulation results based on these two datasets reveal, on the whole, that the proposed ANC does enjoy higher capability to deal with nonlinearity between MECG and AECG as compared with previous ANCs in terms of fetal QRS (FQRS)-related statistics and morphology of the extracted FECG waveforms. In particular, for the second real subdataset, the F1-measure results produced by the PCA-based template subtraction (TSpca) technique and six (6) single-reference channel ANCs using LMS- and RLS-based FIR filters, Volterra filter, FLANN, GFLANN, and adaptive echo state neural network (ESN a ) are 92.47%, 93.70%, 94.07%, 94.22%, 94.90%, 94.90%, and 95.46%, respectively. The same F1-measure statistical results from five (5) multi-reference channel ANCs (LMS- and RLS-based FIR filters, Volterra filter, FLANN, and GFLANN) for the second real subdataset turn out to be 94.08%, 94.29%, 94.68%, 94.91%, and 94.96%, respectively. These results indicate that the ESN a and GFLANN perform best, with the ESN a being slightly better than the GFLANN but about four times more

  12. Adaptive cancellation techniques

    NASA Astrophysics Data System (ADS)

    1983-11-01

    An adaptive signal canceller has been evaluated for the enhancement of pulse signal reception during the transmission of a high power ECM jamming signal. The canceller design is based on the use of DRFM(Digital RF Memory) technology as part of an adaptive multiple tapped delay line. The study includes analysis of relationship of tap spacing and waveform bandwidth, survey of related documents in areas of sidelobe cancellers, transversal equalizers, and adaptive filters, and derivation of control equations and corresponding control processes. The simulation of overall processes included geometric analysis of the multibeam transmitting antenna, multiple reflection sources and the receiving antenna; waveforms, tap spacings and bandwidths; and alternate control algorithms. Conclusions are provided regarding practical system control algorithms, design characteristics and limitations.

  13. Active noise canceling system for mechanically cooled germanium radiation detectors

    DOEpatents

    Nelson, Karl Einar; Burks, Morgan T

    2014-04-22

    A microphonics noise cancellation system and method for improving the energy resolution for mechanically cooled high-purity Germanium (HPGe) detector systems. A classical adaptive noise canceling digital processing system using an adaptive predictor is used in an MCA to attenuate the microphonics noise source making the system more deployable.

  14. Background noise cancellation of manatee vocalizations using an adaptive line enhancer.

    PubMed

    Yan, Zheng; Niezrecki, Christopher; Cattafesta, Louis N; Beusse, Diedrich O

    2006-07-01

    The West Indian manatee (Trichechus manatus latirostris) has become an endangered species partly because of an increase in the number of collisions with boats. A device to alert boaters of the presence of manatees is desired. Previous research has shown that background noise limits the manatee vocalization detection range (which is critical for practical implementation). By improving the signal-to-noise ratio of the measured manatee vocalization signal, it is possible to extend the detection range. The finite impulse response (FIR) structure of the adaptive line enhancer (ALE) can detect and track narrow-band signals buried in broadband noise. In this paper, a constrained infinite impulse response (IIR) ALE, called a feedback ALE (FALE), is implemented to reduce the background noise. In addition, a bandpass filter is used as a baseline for comparison. A library consisting of 100 manatee calls spanning ten different signal categories is used to evaluate the performance of the bandpass filter, FIR-ALE, and FALE. The results show that the FALE is capable of reducing background noise by about 6.0 and 21.4 dB better than that of the FIR-ALE and bandpass filter, respectively, when the signal-to-noise ratio (SNR) of the original manatee call is -5 dB. PMID:16875212

  15. Wireless rake-receiver using adaptive filter with a family of partial update algorithms in noise cancellation applications

    NASA Astrophysics Data System (ADS)

    Fayadh, Rashid A.; Malek, F.; Fadhil, Hilal A.; Aldhaibani, Jaafar A.; Salman, M. K.; Abdullah, Farah Salwani

    2015-05-01

    For high data rate propagation in wireless ultra-wideband (UWB) communication systems, the inter-symbol interference (ISI), multiple-access interference (MAI), and multiple-users interference (MUI) are influencing the performance of the wireless systems. In this paper, the rake-receiver was presented with the spread signal by direct sequence spread spectrum (DS-SS) technique. The adaptive rake-receiver structure was shown with adjusting the receiver tap weights using least mean squares (LMS), normalized least mean squares (NLMS), and affine projection algorithms (APA) to support the weak signals by noise cancellation and mitigate the interferences. To minimize the data convergence speed and to reduce the computational complexity by the previous algorithms, a well-known approach of partial-updates (PU) adaptive filters were employed with algorithms, such as sequential-partial, periodic-partial, M-max-partial, and selective-partial updates (SPU) in the proposed system. The simulation results of bit error rate (BER) versus signal-to-noise ratio (SNR) are illustrated to show the performance of partial-update algorithms that have nearly comparable performance with the full update adaptive filters. Furthermore, the SPU-partial has closed performance to the full-NLMS and full-APA while the M-max-partial has closed performance to the full-LMS updates algorithms.

  16. Noise canceling in-situ detection

    SciTech Connect

    Walsh, David O.

    2014-08-26

    Technologies applicable to noise canceling in-situ NMR detection and imaging are disclosed. An example noise canceling in-situ NMR detection apparatus may comprise one or more of a static magnetic field generator, an alternating magnetic field generator, an in-situ NMR detection device, an auxiliary noise detection device, and a computer.

  17. Passive Phase Noise Cancellation Scheme

    PubMed Central

    Kenig, Eyal; Cross, M. C.; Lifshitz, Ron; Karabalin, R. B.; Villanueva, L. G.; Matheny, M. H.; Roukes, M. L.

    2013-01-01

    We introduce a new method for reducing phase noise in oscillators, thereby improving their frequency precision. The noise reduction is realized by a passive device consisting of a pair of coupled nonlinear resonating elements that are driven parametrically by the output of a conventional oscillator at a frequency close to the sum of the linear mode frequencies. Above the threshold for parametric instability, the coupled resonators exhibit self-oscillations which arise as a response to the parametric driving, rather than by application of active feedback. We find operating points of the device for which this periodic signal is immune to frequency noise in the driving oscillator, providing a way to clean its phase noise. We present results for the effect of thermal noise to advance a broader understanding of the overall noise sensitivity and the fundamental operating limits. PMID:23004985

  18. Background noise cancellation for improved acoustic detection of manatee vocalizations

    NASA Astrophysics Data System (ADS)

    Yan, Zheng; Niezrecki, Christopher; Beusse, Diedrich O.

    2005-04-01

    The West Indian manatee (Trichechus manatus latirostris) has become endangered partly because of an increase in the number of collisions with boats. A device to alert boaters of the presence of manatees, so that a collision can be avoided, is desired. Practical implementation of the technology is dependent on the hydrophone spacing and range of detection. These parameters are primarily dependent on the manatee vocalization strength, the decay of the signal strength with distance, and the background noise levels. An efficient method to extend the detection range by using background noise cancellation is proposed in this paper. An adaptive line enhancer (ALE) that can detect and track narrowband signals buried in broadband noise is implemented to cancel the background noise. The results indicate that the ALE algorithm can efficiently extract the manatee calls from the background noise. The improved signal-to-noise ratio of the signal can be used to extend the range of detection of manatee vocalizations and reduce the false alarm and missing detection rate in their natural habitat.

  19. Background noise cancellation for improved acoustic detection of manatee vocalizations

    NASA Astrophysics Data System (ADS)

    Yan, Zheng; Niezrecki, Christopher; Beusse, Diedrich O.

    2005-06-01

    The West Indian manatee (Trichechus manatus latirostris) has become endangered partly because of an increase in the number of collisions with boats. A device to alert boaters of the presence of manatees, so that a collision can be avoided, is desired. A practical implementation of the technology is dependent on the hydrophone spacing and range of detection. These parameters are primarily dependent on the manatee vocalization strength, the decay of the signal's strength with distance, and the background noise levels. An efficient method to extend the detection range by using background noise cancellation is proposed in this paper. An adaptive line enhancer (ALE) that can detect and track narrow band signals buried in broadband noise is implemented to cancel the background noise. The results indicate that the ALE algorithm can efficiently extract the manatee calls from the background noise. The improved signal-to-noise ratio of the signal can be used to extend the range of detection of manatee vocalizations and reduce the false alarm and missing detection rate in their natural habitat. .

  20. Driver Module for Noise Cancellation System

    NASA Astrophysics Data System (ADS)

    Shirvani, Mir S.

    2002-12-01

    The Driver module is an integral part of the noise cancellation system, which was my primary objective to research, design, and prototype during the tenure in NASA Langley research center. The function of the driver module is to actuate a panel that is constructed with a smart material and invented in NASA-LaRC. The bandwidth and amplitude of the actuation of the panel correlates the undesirable structural bandwidth and amplitude of the applied object. The undesirable structural bandwidth is relatively narrow and the undesirable amplitude is relatively large. A highly stable, low distortion, linear monolithic integrated circuit was used as a variable frequency and amplitude function generator. In order to elevate the amplitude of the output waveform of the generator to a sufficient magnitude a pair of high voltage monolithic MOSFET operational amplifiers were implemented. The amplifiers connected in a bipolar bridge configuration for a higher efficiency. In order to reduce the required external Supply voltages and make the driver capable to be operated by a battery a pair of ultra miniature high-output voltage dc to dc converters are also used. The driver module tested with the noise cancellation panel, the required data was acquired, and the result was promising. After examining all the options the driver module was designed and prototyped.

  1. A New Method to Cancel RFI---The Adaptive Filter

    NASA Astrophysics Data System (ADS)

    Bradley, R.; Barnbaum, C.

    1996-12-01

    An increasing amount of precious radio frequency spectrum in the VHF, UHF, and microwave bands is being utilized each year to support new commercial and military ventures, and all have the potential to interfere with radio astronomy observations. Some radio spectral lines of astronomical interest occur outside the protected radio astronomy bands and are unobservable due to heavy interference. Conventional approaches to deal with RFI include legislation, notch filters, RF shielding, and post-processing techniques. Although these techniques are somewhat successful, each suffers from insufficient interference cancellation. One concept of interference excision that has not been used before in radio astronomy is adaptive interference cancellation. The concept of adaptive interference canceling was first introduced in the mid-1970s as a way to reduce unwanted noise in low frequency (audio) systems. Examples of such systems include the canceling of maternal ECG in fetal electrocardiography and the reduction of engine noise in the passenger compartment of automobiles. Only recently have high-speed digital filter chips made adaptive filtering possible in a bandwidth as large a few megahertz, finally opening the door to astronomical uses. The system consists of two receivers: the main beam of the radio telescope receives the desired signal corrupted by RFI coming in the sidelobes, and the reference antenna receives only the RFI. The reference antenna is processed using a digital adaptive filter and then subtracted from the signal in the main beam, thus producing the system output. The weights of the digital filter are adjusted by way of an algorithm that minimizes, in a least-squares sense, the power output of the system. Through an adaptive-iterative process, the interference canceler will lock onto the RFI and the filter will adjust itself to minimize the effect of the RFI at the system output. We are building a prototype 100 MHz receiver and will measure the cancellation

  2. Real-time vehicle noise cancellation techniques for gunshot acoustics

    NASA Astrophysics Data System (ADS)

    Ramos, Antonio L. L.; Holm, Sverre; Gudvangen, Sigmund; Otterlei, Ragnvald

    2012-06-01

    Acoustical sniper positioning systems rely on the detection and direction-of-arrival (DOA) estimation of the shockwave and the muzzle blast in order to provide an estimate of a potential snipers location. Field tests have shown that detecting and estimating the DOA of the muzzle blast is a rather difficult task in the presence of background noise sources, e.g., vehicle noise, especially in long range detection and absorbing terrains. In our previous work presented in the 2011 edition of this conference we highlight the importance of improving the SNR of the gunshot signals prior to the detection and recognition stages, aiming at lowering the false alarm and miss-detection rates and, thereby, increasing the reliability of the system. This paper reports on real-time noise cancellation techniques, like Spectral Subtraction and Adaptive Filtering, applied to gunshot signals. Our model assumes the background noise as being short-time stationary and uncorrelated to the impulsive gunshot signals. In practice, relatively long periods without signal occur and can be used to estimate the noise spectrum and its first and second order statistics as required in the spectral subtraction and adaptive filtering techniques, respectively. The results presented in this work are supported with extensive simulations based on real data.

  3. Enhanced Processing for a Towed Array Using an Optimal Noise Canceling Approach

    SciTech Connect

    Sullivan, E J; Candy, J V

    2005-07-21

    Noise self-generated by a surface ship towing an array in search of a weak target presents a major problem for the signal processing especially if broadband techniques are being employed. In this paper we discuss the development and application of an adaptive noise canceling processor capable of extracting the weak far-field acoustic target in a noisy ocean acoustic environment. The fundamental idea for this processor is to use a model-based approach incorporating both target and ship noise. Here we briefly describe the underlying theory and then demonstrate through simulation how effective the canceller and target enhancer perform. The adaptivity of the processor not only enables the ''tracking'' of the canceller coefficients, but also the estimation of target parameters for localization. This approach which is termed ''joint'' cancellation and enhancement produces the optimal estimate of both in a minimum (error) variance sense.

  4. Experimental testing of the noise-canceling processor.

    PubMed

    Collins, Michael D; Baer, Ralph N; Simpson, Harry J

    2011-09-01

    Signal-processing techniques for localizing an acoustic source buried in noise are tested in a tank experiment. Noise is generated using a discrete source, a bubble generator, and a sprinkler. The experiment has essential elements of a realistic scenario in matched-field processing, including complex source and noise time series in a waveguide with water, sediment, and multipath propagation. The noise-canceling processor is found to outperform the Bartlett processor and provide the correct source range for signal-to-noise ratios below -10 dB. The multivalued Bartlett processor is found to outperform the Bartlett processor but not the noise-canceling processor.

  5. Laboratory Investigation of Noise-Canceling Headphones Utilizing "Mr. Blockhead"

    ERIC Educational Resources Information Center

    Koser, John

    2013-01-01

    While I was co-teaching an introductory course in musical acoustics a few years ago, our class investigated several pieces of equipment designed for audio purposes. One piece of such equipment was a pair of noise-canceling headphones. Our students were curious as to how these devices were in eliminating background noise and whether they indeed…

  6. Noise-Canceling Helmet Audio System

    NASA Technical Reports Server (NTRS)

    Seibert, Marc A.; Culotta, Anthony J.

    2007-01-01

    A prototype helmet audio system has been developed to improve voice communication for the wearer in a noisy environment. The system was originally intended to be used in a space suit, wherein noise generated by airflow of the spacesuit life-support system can make it difficult for remote listeners to understand the astronaut s speech and can interfere with the astronaut s attempt to issue vocal commands to a voice-controlled robot. The system could be adapted to terrestrial use in helmets of protective suits that are typically worn in noisy settings: examples include biohazard, fire, rescue, and diving suits. The system (see figure) includes an array of microphones and small loudspeakers mounted at fixed positions in a helmet, amplifiers and signal-routing circuitry, and a commercial digital signal processor (DSP). Notwithstanding the fixed positions of the microphones and loudspeakers, the system can accommodate itself to any normal motion of the wearer s head within the helmet. The system operates in conjunction with a radio transceiver. An audio signal arriving via the transceiver intended to be heard by the wearer is adjusted in volume and otherwise conditioned and sent to the loudspeakers. The wearer s speech is collected by the microphones, the outputs of which are logically combined (phased) so as to form a microphone- array directional sensitivity pattern that discriminates in favor of sounds coming from vicinity of the wearer s mouth and against sounds coming from elsewhere. In the DSP, digitized samples of the microphone outputs are processed to filter out airflow noise and to eliminate feedback from the loudspeakers to the microphones. The resulting conditioned version of the wearer s speech signal is sent to the transceiver.

  7. Adaptive Suppression of Noise in Voice Communications

    NASA Technical Reports Server (NTRS)

    Kozel, David; DeVault, James A.; Birr, Richard B.

    2003-01-01

    A subsystem for the adaptive suppression of noise in a voice communication system effects a high level of reduction of noise that enters the system through microphones. The subsystem includes a digital signal processor (DSP) plus circuitry that implements voice-recognition and spectral- manipulation techniques. The development of the adaptive noise-suppression subsystem was prompted by the following considerations: During processing of the space shuttle at Kennedy Space Center, voice communications among test team members have been significantly impaired in several instances because some test participants have had to communicate from locations with high ambient noise levels. Ear protection for the personnel involved is commercially available and is used in such situations. However, commercially available noise-canceling microphones do not provide sufficient reduction of noise that enters through microphones and thus becomes transmitted on outbound communication links.

  8. Constrained adaptation for feedback cancellation in hearing aids.

    PubMed

    Kates, J M

    1999-08-01

    In feedback cancellation in hearing aids, an adaptive filter is used to model the feedback path. The output of the adaptive filter is subtracted from the microphone signal to cancel the acoustic and mechanical feedback picked up by the microphone, thus allowing more gain in the hearing aid. In general, the feedback-cancellation filter adapts on the hearing-aid input signal, and signal cancellation and coloration artifacts can occur for a narrow-band input. In this paper, two procedures for LMS adaptation with a constraint on the magnitude of the adaptive weight vector are derived. The constraints greatly reduce the probability that the adaptive filter will cancel a narrow-band input. Simulation results are used to demonstrate the efficacy of the constrained adaptation. PMID:10462806

  9. Laboratory Investigation of Noise-Canceling Headphones Utilizing ``Mr. Blockhead''

    NASA Astrophysics Data System (ADS)

    Koser, John

    2013-09-01

    While I was co-teaching an introductory course in musical acoustics a few years ago, our class investigated several pieces of equipment designed for audio purposes. One piece of such equipment was a pair of noise-canceling headphones. Our students were curious as to how these devices were in eliminating background noise and whether they indeed block low-frequency sounds as advertised.

  10. A Nonlinear Adaptive Filter for Gyro Thermal Bias Error Cancellation

    NASA Technical Reports Server (NTRS)

    Galante, Joseph M.; Sanner, Robert M.

    2012-01-01

    Deterministic errors in angular rate gyros, such as thermal biases, can have a significant impact on spacecraft attitude knowledge. In particular, thermal biases are often the dominant error source in MEMS gyros after calibration. Filters, such as J\\,fEKFs, are commonly used to mitigate the impact of gyro errors and gyro noise on spacecraft closed loop pointing accuracy, but often have difficulty in rapidly changing thermal environments and can be computationally expensive. In this report an existing nonlinear adaptive filter is used as the basis for a new nonlinear adaptive filter designed to estimate and cancel thermal bias effects. A description of the filter is presented along with an implementation suitable for discrete-time applications. A simulation analysis demonstrates the performance of the filter in the presence of noisy measurements and provides a comparison with existing techniques.

  11. Performance benefits of adaptive, multimicrophone, interference-canceling systems in everyday environments

    NASA Astrophysics Data System (ADS)

    Desloge, Joseph G.; Zimmer, Martin J.; Zurek, Patrick M.

    2001-05-01

    Adaptive multimicrophone systems are currently used for a variety of noise-cancellation applications (such as hearing aids) to preserve signals arriving from a particular (target) direction while canceling other (jammer) signals in the environment. Although the performance of these systems is known to degrade with increasing reverberation, there are few measurements of adaptive performance in everyday reverberant environments. In this study, adaptive performance was compared to that of a simple, nonadaptive cardioid microphone to determine a measure of adaptive benefit. Both systems used recordings (at an Fs of 22050 Hz) from the same two omnidirectional microphones, which were separated by 1 cm. Four classes of environment were considered: outdoors, household, parking garage, and public establishment. Sources were either environmental noises (e.g., household appliances, restaurant noise) or a controlled noise source. In all situations, no target was present (i.e., all signals were jammers) to obtain maximal jammer cancellation. Adaptive processing was based upon the Griffiths-Jim generalized sidelobe canceller using filter lengths up to 400 points. Average intelligibility-weighted adaptive benefit levels at a source distance of 1 m were, at most, 1.5 dB for public establishments, 2 dB for household rooms and the parking garage, and 3 dB outdoors. [Work supported by NIOSH.

  12. A differential magnetoelectric heterostructure: Internal noise reduction and external noise cancellation

    NASA Astrophysics Data System (ADS)

    Wang, Yaojin; Li, Jiefang; Viehland, D.

    2015-12-01

    A differential heterostructure design which has a capability to reduce the internal noise and reject the external vibration noise for Metglas magnetostrictive foils/Pb(Zr, Ti)O3 piezofiber based-magnetoelectric (ME) laminated composite has been studied. The internal noise reduction is equivalent to that offered by sensor array stacks, and the external noise cancellation is based on a differential method (i.e., ME signal is in-phase but vibration noise is anti-phase). The ability of the structure to reduce the internal noise, and cancel the external vibration noise by a 10-fold attenuation factor, allows for practical applications of these sensors in real-world environments where contamination of magnetic signals by external vibrational noise increases the equivalent magnetic noise.

  13. Newtonian noise cancellation in tensor gravitational wave detector

    NASA Astrophysics Data System (ADS)

    Paik, Ho Jung; Harms, Jan

    2016-05-01

    Terrestrial gravity noise produced by ambient seismic and infrasound fields poses one of the main sensitivity limitations in low-frequency ground-based gravitational-wave (GW) detectors. This noise needs to be suppressed by 3-5 orders of magnitude in the frequency band 10 mHz to 1 Hz, which is extremely challenging. We present a new approach that greatly facilitates cancellation of gravity noise in full-tensor GW detectors. It makes explicit use of the direction of propagation of a GW, and can therefore either be implemented in directional searches for GWs or in observations of known sources. We show that suppression of the Newtonian-noise foreground is greatly facilitated using the extra strain channels in full-tensor GW detectors. Only a modest number of auxiliary, high-sensitivity environmental sensors is required to achieve noise suppression by a few orders of magnitude.

  14. First Experimental Demonstration of Noise Cancellation for LISA Interferometry

    NASA Astrophysics Data System (ADS)

    De Vine, Glenn; Shaddock, D.; Ware, B.; Spero, R.; Klipstein, W.

    2009-01-01

    We report on the first experimental demonstration of post-processed, time-delay interferometry with USO noise cancellation for the Laser Interferometer Space Antenna. The demonstration used simplified optical benches constructed from ultra-low expansion glass and the LISA phasemeter prototype. Each bench was incorporated into an end station, consisting of two NPRO lasers, and three phase measurements (two inter-bench measurements and one local measurement). The interferometer has been designed to provide signals representative of LISA interferometry. The laser frequency noise-free combination, alpha, was formed by combining the six phase measurements from the two end stations, each of which contained a clock which was used as the master reference for that bench's three phase measurements. The phase measurements were interpolated in post-processing to correct for errors in sampling times caused by relative drift of the end stations' clocks. After interpolation, the laser frequency noise in alpha was reduced by almost 4 orders of magnitude (relative to the noise level in the individual phase measurements) down to the performance limit of the interferometer. As expected, the independent clocks' phase fluctuations also caused a large increase in the measured noise. This clock phase noise was removed by phase modulating the clock frequencies onto laser beams exchanged between spacecraft in the manner planned for LISA. The clock noise was suppressed by almost 5 orders of magnitude. Notably, both the laser frequency noise and clock noise were suppressed down to our interferometer displacement noise level of 20 pm/√Hz at 0.1 Hz. Although this noise meets the LISA minimum mission requirement, work is ongoing to reduce the pathlength noise low enough to demonstrate laser frequency noise and clock noise suppression to below the error allocation of approximately 13 pm/√Hz. The current results validate both the expected performance of TDI as well as the performance of the

  15. Maximizing Adaptivity in Hierarchical Topological Models Using Cancellation Trees

    SciTech Connect

    Bremer, P; Pascucci, V; Hamann, B

    2008-12-08

    We present a highly adaptive hierarchical representation of the topology of functions defined over two-manifold domains. Guided by the theory of Morse-Smale complexes, we encode dependencies between cancellations of critical points using two independent structures: a traditional mesh hierarchy to store connectivity information and a new structure called cancellation trees to encode the configuration of critical points. Cancellation trees provide a powerful method to increase adaptivity while using a simple, easy-to-implement data structure. The resulting hierarchy is significantly more flexible than the one previously reported. In particular, the resulting hierarchy is guaranteed to be of logarithmic height.

  16. A New Approach to Interference Excision in Radio Astronomy: Real-Time Adaptive Cancellation

    NASA Astrophysics Data System (ADS)

    Barnbaum, Cecilia; Bradley, Richard F.

    1998-11-01

    Every year, an increasing amount of radio-frequency (RF) spectrum in the VHF, UHF, and microwave bands is being utilized to support new commercial and military ventures, and all have the potential to interfere with radio astronomy observations. Such services already cause problems for radio astronomy even in very remote observing sites, and the potential for this form of light pollution to grow is alarming. Preventive measures to eliminate interference through FCC legislation and ITU agreements can be effective; however, many times this approach is inadequate and interference excision at the receiver is necessary. Conventional techniques such as RF filters, RF shielding, and postprocessing of data have been only somewhat successful, but none has been sufficient. Adaptive interference cancellation is a real-time approach to interference excision that has not been used before in radio astronomy. We describe here, for the first time, adaptive interference cancellation in the context of radio astronomy instrumentation, and we present initial results for our prototype receiver. In the 1960s, analog adaptive interference cancelers were developed that obtain a high degree of cancellation in problems of radio communications and radar. However, analog systems lack the dynamic range, noised performance, and versatility required by radio astronomy. The concept of digital adaptive interference cancellation was introduced in the mid-1960s as a way to reduce unwanted noise in low-frequency (audio) systems. Examples of such systems include the canceling of maternal ECG in fetal electrocardiography and the reduction of engine noise in the passenger compartments of automobiles. These audio-frequency applications require bandwidths of only a few tens of kilohertz. Only recently has high-speed digital filter technology made high dynamic range adaptive canceling possible in a bandwidth as large as a few megahertz, finally opening the door to application in radio astronomy. We have

  17. Transient plasma estimation: a noise cancelling/identification approach

    SciTech Connect

    Candy, J.V.; Casper, T.; Kane, R.

    1985-03-01

    The application of a noise cancelling technique to extract energy storage information from sensors occurring during fusion reactor experiments on the Tandem Mirror Experiment-Upgrade (TMX-U) at the Lawrence Livermore National Laboratory (LLNL) is examined. We show how this technique can be used to decrease the uncertainty in the corresponding sensor measurements used for diagnostics in both real-time and post-experimental environments. We analyze the performance of algorithm on the sensor data and discuss the various tradeoffs. The algorithm suggested is designed using SIG, an interactive signal processing package developed at LLNL.

  18. An On-Chip Noise Canceller with High Voltage Supply Lines for Nanosecond-Range Power Supply Noise

    NASA Astrophysics Data System (ADS)

    Nakamura, Yasumi; Takamiya, Makoto; Sakurai, Takayasu

    An on-chip power supply noise canceller with higher voltage supply and switching transistor is proposed and the effectiveness of the canceller is experimentally verified. The noise canceller is effective for nano-second order noise caused by circuit wakeup or step increase of frequency in frequency hopping. The principle of the noise canceller is to reduce the current flowing through the supply line of VDD by injecting additional current from the higher voltage supply, so that the voltage drop across the VDD supply line is reduced. As additional current flow from higher supply, switching transistor has to be turned off not to increase the power consumption. With turn-off time of 2L/R, this current can be turned off without inducting another droop due to the increase of current flowing through the power supply line. The measurement shows the canceller reduces 68% of the noise with load circuit equivalent to 530k logic gates in 90-nm CMOS with 9% wire overhead, 1.5% area overhead, and 3% power overhead at 50k wake-ups/s. Compared to passive noise reduction, proposed noise canceller reduces power supply noise by 64% without wire overhead and to achieve same noise reduction with passive method, 77 times more C or 45 times less L is required. Too large switching transistor results in saturated noise reduction effect and higher power consumption. A rule-of-thumb is to set the on-resistance to supply 100% of load current when turned-on.

  19. Characteristics of noise-canceling headphones to reduce the hearing hazard for MP3 users.

    PubMed

    Liang, Maojin; Zhao, Fei; French, David; Zheng, Yiqing

    2012-06-01

    Three pairs of headphones [standard iPod ear buds and two noise-canceling headphones (NCHs)] were chosen to investigate frequency characteristics of noise reduction, together with their attenuation effects on preferred listening levels (PLLs) in the presence of various types of background noise. Twenty-six subjects with normal hearing chose their PLLs in quiet, street noise, and subway noise using the three headphones and with the noise-canceling system on/off. Both sets of NCHs reduced noise levels at mid- and high-frequencies. Further noise reductions occurred in low frequencies with the noise canceling system switched on. In street noise, both NCHs had similar noise reduction effects. In subway noise, better noise reduction effects were found in the expensive NCH and with noise-canceling on. A two way repeated measures analysis of variance showed that both listening conditions and headphone styles were significant influencing factors on the PLLs. Subjects tended to increase their PLLs as the background noise level increased. Compared with ear buds, PLLs obtained from NCHs-on in the presence of background noise were reduced up to 4 dB. Therefore, proper selection and use of NCHs appears beneficial in reducing the risk of hearing damage caused by high music listening levels in the presence of background noise.

  20. Model of aircraft noise adaptation

    NASA Technical Reports Server (NTRS)

    Dempsey, T. K.; Coates, G. D.; Cawthorn, J. M.

    1977-01-01

    Development of an aircraft noise adaptation model, which would account for much of the variability in the responses of subjects participating in human response to noise experiments, was studied. A description of the model development is presented. The principal concept of the model, was the determination of an aircraft adaptation level which represents an annoyance calibration for each individual. Results showed a direct correlation between noise level of the stimuli and annoyance reactions. Attitude-personality variables were found to account for varying annoyance judgements.

  1. Microwave Photonic Filters for Interference Cancellation and Adaptive Beamforming

    NASA Astrophysics Data System (ADS)

    Chang, John

    Wireless communication has experienced an explosion of growth, especially in the past half- decade, due to the ubiquity of wireless devices, such as tablets, WiFi-enabled devices, and especially smartphones. Proliferation of smartphones with powerful processors and graphic chips have given an increasing amount of people the ability to access anything from anywhere. Unfortunately, this ease of access has greatly increased mobile wireless bandwidth and have begun to stress carrier networks and spectra. Wireless interference cancellation will play a big role alongside the popularity of wire- less communication. In this thesis, we will investigate optical signal processing methods for wireless interference cancellation methods. Optics provide the perfect backdrop for interference cancellation. Mobile wireless data is already aggregated and transported through fiber backhaul networks in practice. By sandwiching the signal processing stage between the receiver and the fiber backhaul, processing can easily be done locally in one location. Further, optics offers the advantages of being instantaneously broadband and size, weight, and power (SWAP). We are primarily concerned with two methods for interference cancellation, based on microwave photonic filters, in this thesis. The first application is for a co-channel situation, in which a transmitter and receiver are co-located and transmitting at the same frequency. A novel analog optical technique extended for multipath interference cancellation of broadband signals is proposed and experimentally demonstrated in this thesis. The proposed architecture was able to achieve a maximum of 40 dB of cancellation over 200 MHz and 50 dB of cancellation over 10 MHz. The broadband nature of the cancellation, along with its depth, demonstrates both the precision of the optical components and the validity of the architecture. Next, we are interested in a scenario with dynamically changing interference, which requires an adaptive photonic

  2. Efficient reference-free adaptive artifact cancellers for impedance cardiography based remote health care monitoring systems.

    PubMed

    Mallam, Madhavi; Rao, K Chandra Bhutan

    2016-01-01

    In this paper, a new model for adaptive artifact cancelation in impedance cardiography (ICG) signals is presented. It is a hybrid model based on wavelet decomposition and an adaptive filter. A novel feature of this model is the implementation of reference-free adaptive artifact cancellers (AAC). For this implementation, the reference signal is constructed using a wavelet transformation. During critical conditions the filter weights may be negative and cause an imbalance in the convergence. To overcome this problem, we introduce non-negative adaptive algorithms in the proposed artifact canceller. To accelerate the performance of the AAC, we propose exponential non-negative and normalized non-negative algorithms to update the filter coefficients. The computational complexity of the filtering section in a remote health care system is important to avoid inter-symbol interference of the incoming samples. This can be achieved by combining sign-based algorithms with the adaptive filtering section. Finally, several AACs are developed using variants of the non-negative algorithms and performance measures are computed and compared. All of the proposed AACs are tested on actual ICG signals. Among the AACs evaluated, sign regressor normalized non-negative LMS (SRN(3)LMS) based adaptive artifact canceller achieves highest signal to noise ratio (SNR). The SNR achieved by this algorithm in baseline wander artifact elimination is 8.5312 dBs, in electrode muscle artifact elimination is 7.5908 dBs and in impedance measurement artifact elimination is 8.4231 dBs. PMID:27386256

  3. Multi-axis analog adaptive feedforward cancellation of cryocooler vibration

    NASA Astrophysics Data System (ADS)

    Collins, Simon Andrew

    1994-01-01

    The vibration produced by Stirling cryocoolers is incompatible with spacecraft-borne precision-pointing imaging instruments. Thermal considerations prevent the addition of sufficient mechanical isolation to eliminate the effects of this vibration. The objective of this research is the design, analysis, and experimental verification of a multi-axis vibration cancellation system for the expander of a split Stirling cryocooler. Cancellation of the periodic cryocooler vibration is achieved with a set of load cells, a custom three-axis electrodynamic actuator, and a narrowband adaptive feedforward controller. In order to size the actuator, a simple model of the cryocooler's vibration is combined with a first-order analysis of a four-magnet two-return-plate forcing element. While the resulting actuator has sufficient force capability, it exhibits significant nonlinearity. A nonlinear actuator model is developed that accounts for in-plane flexure restraint due to both large-amplitude static deflections and large-amplitude vibrations. Numerical solutions of the nonlinear model accurately reflect jump phenomena and higher harmonics observed in the actuator's response. The adaptive feedforward controller employs the filtered-x least-mean-square (FXLMS) algorithm to update an adaptive filter. Rather than implementing this filter with a digital signal processor (DSP), for which there is little flight heritage, a continuous-time analog realization of the FXLMS filter is selected. Theoretically, the FXLMS filter may be represented by an equivalent linear transfer function. However a comprehensive treatment of factors associated with the actual implementation reveals the limitations of the transfer function representation. Factors such as harmonic distortion of the reference signal and imperfect quadrature are shown to result in frequency-shifted terms in the filter's output. The presence of these output components is confirmed experimentally, and their effect on performance is

  4. Joint application of a statistical optimization process and Empirical Mode Decomposition to Magnetic Resonance Sounding Noise Cancelation

    NASA Astrophysics Data System (ADS)

    Ghanati, Reza; Fallahsafari, Mahdi; Hafizi, Mohammad Kazem

    2014-12-01

    The signal quality of Magnetic Resonance Sounding (MRS) measurements is a crucial criterion. The accuracy of the estimation of the signal parameters (i.e. E0 and T2*) strongly depends on amplitude and conditions of ambient electromagnetic interferences at the site of investigation. In this paper, in order to enhance the performance in the noisy environments, a two-step noise cancelation approach based on the Empirical Mode Decomposition (EMD) and a statistical method is proposed. In the first stage, the noisy signal is adaptively decomposed into intrinsic oscillatory components called intrinsic mode functions (IMFs) by means of the EMD algorithm. Afterwards based on an automatic procedure the noisy IMFs are detected, and then the partly de-noised signal is reconstructed through the no-noise IMFs. In the second stage, the signal obtained from the initial section enters an optimization process to cancel the remnant noise, and consequently, estimate the signal parameters. The strategy is tested on a synthetic MRS signal contaminated with Gaussian noise, spiky events and harmonic noise, and on real data. By applying successively the proposed steps, we can remove the noise from the signal to a high extent and the performance indexes, particularly signal to noise ratio, will increase significantly.

  5. Combination of Adaptive Feedback Cancellation and Binaural Adaptive Filtering in Hearing Aids

    NASA Astrophysics Data System (ADS)

    Lombard, Anthony; Reindl, Klaus; Kellermann, Walter

    2009-12-01

    We study a system combining adaptive feedback cancellation and adaptive filtering connecting inputs from both ears for signal enhancement in hearing aids. For the first time, such a binaural system is analyzed in terms of system stability, convergence of the algorithms, and possible interaction effects. As major outcomes of this study, a new stability condition adapted to the considered binaural scenario is presented, some already existing and commonly used feedback cancellation performance measures for the unilateral case are adapted to the binaural case, and possible interaction effects between the algorithms are identified. For illustration purposes, a blind source separation algorithm has been chosen as an example for adaptive binaural spatial filtering. Experimental results for binaural hearing aids confirm the theoretical findings and the validity of the new measures.

  6. Bearing fault diagnosis under unknown variable speed via gear noise cancellation and rotational order sideband identification

    NASA Astrophysics Data System (ADS)

    Wang, Tianyang; Liang, Ming; Li, Jianyong; Cheng, Weidong; Li, Chuan

    2015-10-01

    The interfering vibration signals of a gearbox often represent a challenging issue in rolling bearing fault detection and diagnosis, particularly under unknown variable rotational speed conditions. Though some methods have been proposed to remove the gearbox interfering signals based on their discrete frequency nature, such methods may not work well under unknown variable speed conditions. As such, we propose a new approach to address this issue. The new approach consists of three main steps: (a) adaptive gear interference removal, (b) fault characteristic order (FCO) based fault detection, and (c) rotational-order-sideband (ROS) based fault type identification. For gear interference removal, an enhanced adaptive noise cancellation (ANC) algorithm has been developed in this study. The new ANC algorithm does not require an additional accelerometer to provide reference input. Instead, the reference signal is adaptively constructed from signal maxima and instantaneous dominant meshing multiple (IDMM) trend. Key ANC parameters such as filter length and step size have also been tailored to suit the variable speed conditions, The main advantage of using ROS for fault type diagnosis is that it is insusceptible to confusion caused by the co-existence of bearing and gear rotational frequency peaks in the identification of the bearing fault characteristic frequency in the FCO sub-order region. The effectiveness of the proposed method has been demonstrated using both simulation and experimental data. Our experimental study also indicates that the proposed method is applicable regardless whether the bearing and gear rotational speeds are proportional to each other or not.

  7. Active Control of Environmental Noise, Vi: Performance of a Fundamental Free-Field Sound Cancelling System

    NASA Astrophysics Data System (ADS)

    WRIGHT, S. E.; ATMOKO, H.

    2001-08-01

    Before the adaptive cancellation performance of multichannel free-field acoustic systems could be evaluated in detail, it was considered prudent to establish first the performance of a single channel free-field cancelling system. The adaptive theory for this basic system, including the stability process, is described. Measured adaptive performance is given confirming the theory.The concept of stability bands and their prediction is considered. The bands are a consequence of phase differences between the primary source and secondary cancelling field, generated by the transfer functions of the control system. At the edge of these stability bands satellite pole frequencies “beat” with the cancelling frequency, generated by the zeros, to produce side bands. The relation between the stability bandwidth and the adaptive speed, in terms of reference signal strength and adaptive step size, are investigated.The sound generation and cancellation performance of this basic canceller are then considered. The acoustic sound field directivity characteristics are similar to that of a dipole, tripole or quadrupole type source, depending on the primary-secondary source separation distance. The acoustic shadow characteristics are established in detail and compared with measurement. Good agreement is obtained.

  8. Adaptive feedback cancellation with frequency compression for hearing aids.

    PubMed

    Joson, H A; Asano, F; Suzuki, Y; Sone, T

    1993-12-01

    The use of an adaptive feedback canceler (AFC) for howling suppression in hearing aids seems very attractive since it is not only unaffected by the changes in the operating environment, but it also limits signal degradation due to the feedback signal. This, however, requires a reference signal which is correlated with the feedback signal but not with the input signal. In hearing aids, such a signal is hard to obtain. The output signal could be used as reference if its correlation with the input signal could sufficiently be removed. If the reference signal is correlated with the input signal, the input signal will also be canceled by the AFC. Here, the use of a frequency compressor as a decorrelator is proposed. The performance of this system is then investigated via digital simulation. Results indicated that with the use of the proposed system and the proper choice of system parameters, an increase of about 18 dB in the howling margin could be achieved with minimal deterioration in output signal quality. PMID:8300960

  9. Cancellation of Laser Noise in Space-Based Interferometer Detectors of Gravitational Radiation

    NASA Technical Reports Server (NTRS)

    Tinto, Massimo

    1999-01-01

    We presented a time-domain procedure for accurately cancelling laser noise fluctuations in an unequal-arm Michelson interferometer. The method involves separately measuring the phase of the returning light relative to the phase of the transmitted light in each arm. By suitable offsetting and differencing of these two time series, the common laser noise is cancelled exactly. The technique presented in this paper is general, in such that it can be implemented with any (Earth as well as space-based) unequal-arms Michelson interferometers,

  10. An adaptive algorithm for noise rejection.

    PubMed

    Lovelace, D E; Knoebel, S B

    1978-01-01

    An adaptive algorithm for the rejection of noise artifact in 24-hour ambulatory electrocardiographic recordings is described. The algorithm is based on increased amplitude distortion or increased frequency of fluctuations associated with an episode of noise artifact. The results of application of the noise rejection algorithm on a high noise population of test tapes are discussed.

  11. Cancellation of Laser Noise in an Unequal-arm Interferometer Detector of Gravitational Radiation

    NASA Technical Reports Server (NTRS)

    Tinto, M.; Armstrong, J. W.

    1998-01-01

    In this paper we present a method for exactly cancelling the laser noise in a one-bounce unequal-arm Michelson interferometer. The method requries separate measurements of the phase difference in each arm, made by interfering the returning laser light in each arm with the outgoing light.

  12. Noise cancellation in magnetoencephalography and electroencephalography with isolated reference sensors

    DOEpatents

    Kraus, Jr., Robert H.; Espy, Michelle A.; Matlachov, Andrei; Volegov, Petr

    2010-06-01

    An apparatus measures electromagnetic signals from a weak signal source. A plurality of primary sensors is placed in functional proximity to the weak signal source with an electromagnetic field isolation surface arranged adjacent the primary sensors and between the weak signal source and sources of ambient noise. A plurality of reference sensors is placed adjacent the electromagnetic field isolation surface and arranged between the electromagnetic isolation surface and sources of ambient noise.

  13. Adaptive feedback cancellation in hearing aids with clipping in the feedback path.

    PubMed

    Freed, Daniel J

    2008-03-01

    Adaptive linear filtering algorithms are commonly used to cancel feedback in hearing aids. The use of these algorithms is based on the assumption that the feedback path is linear, so nonlinearities in the feedback path may affect performance. This study investigated the effect on feedback canceller performance of clipping of the feedback signal arriving at the microphone, as well as the benefit of applying identical clipping to the cancellation signal so that the cancellation path modeled the nonlinearity of the feedback path. Feedback signal clipping limited the amount of added stable gain that the feedback canceller could provide, and caused misadjustment in response to high-level inputs, by biasing adaptive filter coefficients toward lower magnitudes. Cancellation signal clipping mitigated these negative effects, permitting higher amounts of added stable gain and less misadjustment in response to high-level inputs, but the benefit was reduced in the presence of the highest-level inputs. PMID:18345849

  14. Noise-cancelling quadrature magnetic position, speed and direction sensor

    DOEpatents

    Preston, Mark A.; King, Robert D.

    1996-01-01

    An array of three magnetic sensors in a single package is employed with a single bias magnet for sensing shaft position, speed and direction of a motor in a high magnetic noise environment. Two of the three magnetic sensors are situated in an anti-phase relationship (i.e., 180.degree. out-of-phase) with respect to the relationship between the other of the two sensors and magnetically salient target, and the third magnetic sensor is situated between the anti-phase sensors. The result is quadrature sensing with noise immunity for accurate relative position, speed and direction measurements.

  15. Adaptive Responses Limited by Intrinsic Noise

    PubMed Central

    Shankar, Prabhat; Nishikawa, Masatoshi; Shibata, Tatsuo

    2015-01-01

    Sensory systems have mechanisms to respond to the external environment and adapt to them. Such adaptive responses are effective for a wide dynamic range of sensing and perception of temporal change in stimulus. However, noise generated by the adaptation system itself as well as extrinsic noise in sensory inputs may impose a limit on the ability of adaptation systems. The relation between response and noise is well understood for equilibrium systems in the form of fluctuation response relation. However, the relation for nonequilibrium systems, including adaptive systems, are poorly understood. Here, we systematically explore such a relation between response and fluctuation in adaptation systems. We study the two network motifs, incoherent feedforward loops (iFFL) and negative feedback loops (nFBL), that can achieve perfect adaptation. We find that the response magnitude in adaption systems is limited by its intrinsic noise, implying that higher response would have higher noise component as well. Comparing the relation of response and noise in iFFL and nFBL, we show that whereas iFFL exhibits adaptation over a wider parameter range, nFBL offers higher response to noise ratio than iFFL. We also identify the condition that yields the upper limit of response for both network motifs. These results may explain the reason of why nFBL seems to be more abundant in nature for the implementation of adaption systems. PMID:26305221

  16. Algebraic cancellation of polarisation noise in fibre interferometers.

    PubMed

    McRae, Terry G; Ngo, Silvie; Lam, Timothy T-Y; McClelland, David E; Chow, Jong H; Shaddock, Daniel A; Gray, Malcolm B

    2016-05-16

    This experiment uses digital interferometry to reduce polarisation noise from a fiber interferometer to the level of double Rayleigh backscatter making precision fiber metrology systems robust for remote field applications. This is achieved with a measurement of the Jones matrix with interferometric sensitivity in real time, limited only by fibre length and processing bandwidth. This new approach leads to potentially new metrology applications and the ability to do ellipsometry without polarisation elements in the output field. PMID:27409872

  17. Adaptive Noise Suppression Using Digital Signal Processing

    NASA Technical Reports Server (NTRS)

    Kozel, David; Nelson, Richard

    1996-01-01

    A signal to noise ratio dependent adaptive spectral subtraction algorithm is developed to eliminate noise from noise corrupted speech signals. The algorithm determines the signal to noise ratio and adjusts the spectral subtraction proportion appropriately. After spectra subtraction low amplitude signals are squelched. A single microphone is used to obtain both eh noise corrupted speech and the average noise estimate. This is done by determining if the frame of data being sampled is a voiced or unvoiced frame. During unvoice frames an estimate of the noise is obtained. A running average of the noise is used to approximate the expected value of the noise. Applications include the emergency egress vehicle and the crawler transporter.

  18. An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network.

    PubMed

    Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

    2015-01-01

    In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20-28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20-30%. PMID:26351656

  19. An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network.

    PubMed

    Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

    2015-01-01

    In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20-28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20-30%.

  20. An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network

    PubMed Central

    Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

    2015-01-01

    In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20–28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20–30%. PMID:26351656

  1. Benign paroxysmal positional vertigo after use of noise-canceling headphones.

    PubMed

    Dan-Goor, Eric; Samra, Monica

    2012-01-01

    Benign paroxysmal positional vertigo (BPPV) is a common cause of vertigo. We describe a case of a woman presenting acutely with a severe episode of disabling positional vertigo. Although she had no known etiologic risk factors, this attack followed 12 hours of continuously wearing digital noise-canceling headphones. This is the first such reported association between BPPV and the use of this gadget. We also provide a short review of BPPV and speculate on the possible pathogenic mechanisms involved.

  2. Neural Control Adaptation to Motor Noise Manipulation.

    PubMed

    Hasson, Christopher J; Gelina, Olga; Woo, Garrett

    2016-01-01

    Antagonistic muscular co-activation can compensate for movement variability induced by motor noise at the expense of increased energetic costs. Greater antagonistic co-activation is commonly observed in older adults, which could be an adaptation to increased motor noise. The present study tested this hypothesis by manipulating motor noise in 12 young subjects while they practiced a goal-directed task using a myoelectric virtual arm, which was controlled by their biceps and triceps muscle activity. Motor noise was increased by increasing the coefficient of variation (CV) of the myoelectric signals. As hypothesized, subjects adapted by increasing antagonistic co-activation, and this was associated with reduced noise-induced performance decrements. A second hypothesis was that a virtual decrease in motor noise, achieved by smoothing the myoelectric signals, would have the opposite effect: co-activation would decrease and motor performance would improve. However, the results showed that a decrease in noise made performance worse instead of better, with no change in co-activation. Overall, these findings suggest that the nervous system adapts to virtual increases in motor noise by increasing antagonistic co-activation, and this preserves motor performance. Reducing noise may have failed to benefit performance due to characteristics of the filtering process itself, e.g., delays are introduced and muscle activity bursts are attenuated. The observed adaptations to increased noise may explain in part why older adults and many patient populations have greater antagonistic co-activation, which could represent an adaptation to increased motor noise, along with a desire for increased joint stability. PMID:26973487

  3. Neural Control Adaptation to Motor Noise Manipulation

    PubMed Central

    Hasson, Christopher J.; Gelina, Olga; Woo, Garrett

    2016-01-01

    Antagonistic muscular co-activation can compensate for movement variability induced by motor noise at the expense of increased energetic costs. Greater antagonistic co-activation is commonly observed in older adults, which could be an adaptation to increased motor noise. The present study tested this hypothesis by manipulating motor noise in 12 young subjects while they practiced a goal-directed task using a myoelectric virtual arm, which was controlled by their biceps and triceps muscle activity. Motor noise was increased by increasing the coefficient of variation (CV) of the myoelectric signals. As hypothesized, subjects adapted by increasing antagonistic co-activation, and this was associated with reduced noise-induced performance decrements. A second hypothesis was that a virtual decrease in motor noise, achieved by smoothing the myoelectric signals, would have the opposite effect: co-activation would decrease and motor performance would improve. However, the results showed that a decrease in noise made performance worse instead of better, with no change in co-activation. Overall, these findings suggest that the nervous system adapts to virtual increases in motor noise by increasing antagonistic co-activation, and this preserves motor performance. Reducing noise may have failed to benefit performance due to characteristics of the filtering process itself, e.g., delays are introduced and muscle activity bursts are attenuated. The observed adaptations to increased noise may explain in part why older adults and many patient populations have greater antagonistic co-activation, which could represent an adaptation to increased motor noise, along with a desire for increased joint stability. PMID:26973487

  4. System and method for motor fault detection using stator current noise cancellation

    DOEpatents

    Zhou, Wei; Lu, Bin; Nowak, Michael P.; Dimino, Steven A.

    2010-12-07

    A system and method for detecting incipient mechanical motor faults by way of current noise cancellation is disclosed. The system includes a controller configured to detect indicia of incipient mechanical motor faults. The controller further includes a processor programmed to receive a baseline set of current data from an operating motor and define a noise component in the baseline set of current data. The processor is also programmed to acquire at least on additional set of real-time operating current data from the motor during operation, redefine the noise component present in each additional set of real-time operating current data, and remove the noise component from the operating current data in real-time to isolate any fault components present in the operating current data. The processor is then programmed to generate a fault index for the operating current data based on any isolated fault components.

  5. Communication system with adaptive noise suppression

    NASA Technical Reports Server (NTRS)

    Kozel, David (Inventor); Devault, James A. (Inventor); Birr, Richard B. (Inventor)

    2007-01-01

    A signal-to-noise ratio dependent adaptive spectral subtraction process eliminates noise from noise-corrupted speech signals. The process first pre-emphasizes the frequency components of the input sound signal which contain the consonant information in human speech. Next, a signal-to-noise ratio is determined and a spectral subtraction proportion adjusted appropriately. After spectral subtraction, low amplitude signals can be squelched. A single microphone is used to obtain both the noise-corrupted speech and the average noise estimate. This is done by determining if the frame of data being sampled is a voiced or unvoiced frame. During unvoiced frames an estimate of the noise is obtained. A running average of the noise is used to approximate the expected value of the noise. Spectral subtraction may be performed on a composite noise-corrupted signal, or upon individual sub-bands of the noise-corrupted signal. Pre-averaging of the input signal's magnitude spectrum over multiple time frames may be performed to reduce musical noise.

  6. An Efficient Adaptive Feedback cancellation using by Independent component analysis for hearing aids.

    PubMed

    Ji, Y S; Jung, S Y; Kwon, S Y; Kim, I Y; Kim, Sun; Lee, S M

    2005-01-01

    In this paper, we proposed a feedback cancellation algorithm based on independent component analysis (ICA) for digital hearing aids. In conventional adaptive feedback cancelling systems, the normalized least mean squares (NLMS) algorithm used to reduce acoustic feedback in which hearing aids occurs, generally at high gains. But primary input signal depend on the acoustic feedback signal in higher-order statistics, proposed algorithm was better acoustic feedback cancelling performance than the conventional NLMS algorithm when the input signal has a Laplacian distribution with high-order processing in real-time simulation of TMS320C 6711 DSK. PMID:17282799

  7. Nonuniformity correction algorithm based on a noise-cancellation system for infrared focal-plane arrays

    NASA Astrophysics Data System (ADS)

    Godoy, Sebastian E.; Torres, Sergio N.; Pezoa, Jorge E.; Hayat, Majeed M.; Wang, Qi

    2007-04-01

    In this paper a novel nonuniformity correction method that compensates for the fixed-pattern noise (FPN) in infrared focal-plane array (IRFPA) sensors is developed. The proposed NUC method compensates for the additive component of the FPN statistically processing the read-out signal using a noise-cancellation system. The main assumption of the method is that a source of noise correlated to the additive noise of the IRFPA is available to the system. Under this assumption, a finite impulse response (FIR) filter is designed to synthesize an estimate of the additive noise. Moreover, exploiting the fact that the assumed source of noise is constant in time, we derive a simple expression to calculate the estimate of the additive noise. Finally, the estimate is subtracted to the raw IR imagery to obtain the corrected version of the images. The performance of the proposed system and its ability to compensate for the FPN are tested with infrared images corrupted by both real and simulated nonuniformity.

  8. Cancellation of lateral displacement noise of three-port gratings for coupling light to cavities.

    PubMed

    Meinders, Melanie; Kroker, Stefanie; Singh, Amrit Pal; Kley, E-Bernhard; Tünnermann, Andreas; Danzmann, Karsten; Schnabel, Roman

    2015-05-01

    Reflection gratings enable light coupling to optical cavities without transmission through substrates. Gratings that have three ports and are mounted in a second-order Littrow configuration even allow the coupling to high-finesse cavities using low diffraction efficiencies. In contrast to conventional transmissive cavity couplers, however, the phase of the diffracted light depends on the lateral position of the grating, which introduces an additional noise coupling. Here, we experimentally demonstrate that this kind of noise cancels out once both diffracted output ports of the grating are combined. We achieve the same signal-to-shot-noise ratio as for a conventional coupler. From this perspective, three-port grating couplers in a second-order Littrow configuration remain a valuable approach to reducing optical absorption of cavity coupler substrates in future gravitational-wave detectors. PMID:25927782

  9. A Distributed Amplifier System for Bilayer Lipid Membrane (BLM) Arrays With Noise and Individual Offset Cancellation.

    PubMed

    Crescentini, Marco; Thei, Frederico; Bennati, Marco; Saha, Shimul; de Planque, Maurits R R; Morgan, Hywel; Tartagni, Marco

    2015-06-01

    Lipid bilayer membrane (BLM) arrays are required for high throughput analysis, for example drug screening or advanced DNA sequencing. Complex microfluidic devices are being developed but these are restricted in terms of array size and structure or have integrated electronic sensing with limited noise performance. We present a compact and scalable multichannel electrophysiology platform based on a hybrid approach that combines integrated state-of-the-art microelectronics with low-cost disposable fluidics providing a platform for high-quality parallel single ion channel recording. Specifically, we have developed a new integrated circuit amplifier based on a novel noise cancellation scheme that eliminates flicker noise derived from devices under test and amplifiers. The system is demonstrated through the simultaneous recording of ion channel activity from eight bilayer membranes. The platform is scalable and could be extended to much larger array sizes, limited only by electronic data decimation and communication capabilities.

  10. System and method for bearing fault detection using stator current noise cancellation

    DOEpatents

    Zhou, Wei; Lu, Bin; Habetler, Thomas G.; Harley, Ronald G.; Theisen, Peter J.

    2010-08-17

    A system and method for detecting incipient mechanical motor faults by way of current noise cancellation is disclosed. The system includes a controller configured to detect indicia of incipient mechanical motor faults. The controller further includes a processor programmed to receive a baseline set of current data from an operating motor and define a noise component in the baseline set of current data. The processor is also programmed to repeatedly receive real-time operating current data from the operating motor and remove the noise component from the operating current data in real-time to isolate any fault components present in the operating current data. The processor is then programmed to generate a fault index for the operating current data based on any isolated fault components.

  11. Hardware Verification of Laser Noise Cancellation and Gravitational Wave Extraction using Time-Delay Interferometry

    NASA Astrophysics Data System (ADS)

    Mitryk, Shawn; Mueller, Guido

    The Laser Interferometer Space Antenna (LISA) is a space-based modified Michelson interfer-ometer designed to measure gravitational radiation in the frequency range from 30 uHz to 1 Hz. The interferometer measurement system (IMS) utilizes one-way laser phase measurements to cancel the laser phase noise, reconstruct the proof-mass motion, and extract the gravitational wave (GW) induced laser phase modulations in post-processing using a technique called time-delay interferometry (TDI). Unfortunately, there exist few hard-ware verification experiments of the IMS. The University of Florida LISA Interferometry Simulator (UFLIS) is designed to perform hardware-in-the-loop simulations of the LISA interferometry system, modeling the characteris-tics of the LISA mission as accurately as possible. This depends, first, on replicating the laser pre-stabilization by locking the laser phase to an ultra-stable Zerodur cavity length reference using the PDH locking method. Phase measurements of LISA-like photodetector beat-notes are taken using the UF-phasemeter (PM) which can measure the laser BN frequency to within an accuracy of 0.22 uHz. The inter-space craft (SC) laser links including the time-delay due to the 5 Gm light travel time along the LISA arms, the laser Doppler shifts due to differential SC motion, and the GW induced laser phase modulations are simulated electronically using the electronic phase delay (EPD) unit. The EPD unit replicates the laser field propagation between SC by measuring a photodetector beat-note frequency with the UF-phasemeter and storing the information in memory. After the requested delay time, the frequency information is added to a Doppler offset and a GW-like frequency modulation. The signal is then regenerated with the inter-SC laser phase affects applied. Utilizing these components, I will present the first complete TDI simulations performed using the UFLIS. The LISA model is presented along-side the simulation, comparing the generation and

  12. Newtonian-noise cancellation in full-tensor gravitational-wave detectors

    NASA Astrophysics Data System (ADS)

    Harms, Jan; Paik, Ho Jung

    2015-07-01

    Terrestrial gravity noise, also known as Newtonian noise, produced by ambient seismic and infrasound fields will pose one of the main sensitivity limitations in low-frequency, ground-based, gravitational-wave (GW) detectors. It is estimated that this noise foreground needs to be suppressed by about 3-5 orders of magnitude in the frequency band 10 mHz to 1 Hz, which will be extremely challenging. In this article, we present a new approach that greatly facilitates cancellation of gravity noise in full-tensor GW detectors. The method uses optimal combinations of tensor channels and environmental sensors such as seismometers and microphones to reduce gravity noise. It makes explicit use of the direction of propagation of a GW and can, therefore, either be implemented in directional searches for GWs or in observations of known sources. We show that by using the extra strain channels in full-tensor GW detectors and a modest number of environmental sensors, the Newtonian-noise foreground can be reduced by a few orders of magnitude independent of the GW direction of propagation.

  13. Force sensing based on coherent quantum noise cancellation in a hybrid optomechanical cavity with squeezed-vacuum injection

    NASA Astrophysics Data System (ADS)

    Motazedifard, Ali; Bemani, F.; Naderi, M. H.; Roknizadeh, R.; Vitali, D.

    2016-07-01

    We propose and analyse a feasible experimental scheme for a quantum force sensor based on the elimination of backaction noise through coherent quantum noise cancellation (CQNC) in a hybrid atom-cavity optomechanical setup assisted with squeezed vacuum injection. The force detector, which allows for a continuous, broadband detection of weak forces well below the standard quantum limit (SQL), is formed by a single optical cavity simultaneously coupled to a mechanical oscillator and to an ensemble of ultracold atoms. The latter acts as a negative-mass oscillator so that atomic noise exactly cancels the backaction noise from the mechanical oscillator due to destructive quantum interference. Squeezed vacuum injection enforces this cancellation and allows sub-SQL sensitivity to be reached in a very wide frequency band, and at much lower input laser powers.

  14. Cancellation of simulated environmental noise as a tool for measuring vocal performance during noise exposure.

    PubMed

    Ternström, Sten; Södersten, Maria; Bohman, Mikael

    2002-06-01

    It can be difficult for the voice clinician to observe or measure how a patient uses his voice in a noisy environment. We consider here a novel method for obtaining this information in the laboratory. Worksite noise and filtered white noise were reproduced over high-fidelity loudspeakers. In this noise, 11 subjects read an instructional text of 1.5 to 2 minutes duration, as if addressing a group of people. Using channel estimation techniques, the site noise was suppressed from the recording, and the voice signal alone was recovered. The attainable noise rejection is limited only by the precision of the experimental setup, which includes the need for the subject to remain still so as not to perturb the estimated acoustic channel. This feasibility study, with 7 female and 4 male subjects, showed that small displacements of the speaker's body, even breathing, impose a practical limit on the attainable noise rejection. The noise rejection was typically 30 dB and maximally 40 dB down over the entire voice spectrum. Recordings thus processed were clean enough to permit voice analysis with the long-time average spectrum and the computerized phonetogram. The effects of site noise on voice sound pressure level, fundamental frequency, long-term average spectrum centroid, phonetogram area, and phonation time were much as expected, but with some interesting differences between females and males.

  15. Fully Integrated Low-Noise Readout Circuit with Automatic Offset Cancellation Loop for Capacitive Microsensors

    PubMed Central

    Song, Haryong; Park, Yunjong; Kim, Hyungseup; Cho, Dong-il Dan; Ko, Hyoungho

    2015-01-01

    Capacitive sensing schemes are widely used for various microsensors; however, such microsensors suffer from severe parasitic capacitance problems. This paper presents a fully integrated low-noise readout circuit with automatic offset cancellation loop (AOCL) for capacitive microsensors. The output offsets of the capacitive sensing chain due to the parasitic capacitances and process variations are automatically removed using AOCL. The AOCL generates electrically equivalent offset capacitance and enables charge-domain fine calibration using a 10-bit R-2R digital-to-analog converter, charge-transfer switches, and a charge-storing capacitor. The AOCL cancels the unwanted offset by binary-search algorithm based on 10-bit successive approximation register (SAR) logic. The chip is implemented using 0.18 μm complementary metal-oxide-semiconductor (CMOS) process with an active area of 1.76 mm2. The power consumption is 220 μW with 3.3 V supply. The input parasitic capacitances within the range of −250 fF to 250 fF can be cancelled out automatically, and the required calibration time is lower than 10 ms. PMID:26473877

  16. Fully integrated low-noise readout circuit with automatic offset cancellation loop for capacitive microsensors.

    PubMed

    Song, Haryong; Park, Yunjong; Kim, Hyungseup; Cho, Dong-Il Dan; Ko, Hyoungho

    2015-10-14

    Capacitive sensing schemes are widely used for various microsensors; however, such microsensors suffer from severe parasitic capacitance problems. This paper presents a fully integrated low-noise readout circuit with automatic offset cancellation loop (AOCL) for capacitive microsensors. The output offsets of the capacitive sensing chain due to the parasitic capacitances and process variations are automatically removed using AOCL. The AOCL generates electrically equivalent offset capacitance and enables charge-domain fine calibration using a 10-bit R-2R digital-to-analog converter, charge-transfer switches, and a charge-storing capacitor. The AOCL cancels the unwanted offset by binary-search algorithm based on 10-bit successive approximation register (SAR) logic. The chip is implemented using 0.18 μm complementary metal-oxide-semiconductor (CMOS) process with an active area of 1.76 mm². The power consumption is 220 μW with 3.3 V supply. The input parasitic capacitances within the range of -250 fF to 250 fF can be cancelled out automatically, and the required calibration time is lower than 10 ms.

  17. Fully integrated low-noise readout circuit with automatic offset cancellation loop for capacitive microsensors.

    PubMed

    Song, Haryong; Park, Yunjong; Kim, Hyungseup; Cho, Dong-Il Dan; Ko, Hyoungho

    2015-01-01

    Capacitive sensing schemes are widely used for various microsensors; however, such microsensors suffer from severe parasitic capacitance problems. This paper presents a fully integrated low-noise readout circuit with automatic offset cancellation loop (AOCL) for capacitive microsensors. The output offsets of the capacitive sensing chain due to the parasitic capacitances and process variations are automatically removed using AOCL. The AOCL generates electrically equivalent offset capacitance and enables charge-domain fine calibration using a 10-bit R-2R digital-to-analog converter, charge-transfer switches, and a charge-storing capacitor. The AOCL cancels the unwanted offset by binary-search algorithm based on 10-bit successive approximation register (SAR) logic. The chip is implemented using 0.18 μm complementary metal-oxide-semiconductor (CMOS) process with an active area of 1.76 mm². The power consumption is 220 μW with 3.3 V supply. The input parasitic capacitances within the range of -250 fF to 250 fF can be cancelled out automatically, and the required calibration time is lower than 10 ms. PMID:26473877

  18. Active Control of Fan Noise: Feasibility Study. Volume 3; Active Fan Noise Cancellation in the NASA Lewis Active Noise Control Fan Facility

    NASA Technical Reports Server (NTRS)

    Pla, Frederic G.; Hu, Ziqiang; Sutliff, Daniel L.

    1996-01-01

    This report describes the Active Noise Cancellation (ANC) System designed by General Electric and tested in the NASA Lewis Research Center's (LERC) 48 inch Active Noise Control Fan (ANCF). The goal of this study is to assess the feasibility of using wall mounted secondary acoustic sources and sensors within the duct of a high bypass turbofan aircraft engine for global active noise cancellation of fan tones. The GE ANC system is based on a modal control approach. A known acoustic mode propagating in the fan duct is canceled using an array of flush-mounted compact sound sources. The canceling modal signal is generated by a modal controller. Inputs to the controller are signals from a shaft encoder and from a microphone array which senses the residual acoustic mode in the duct. The key results are that the (6,0) was completely eliminated at the 920 Hz design frequency and substantially reduced elsewhere. The total tone power was reduced 6.8 dB (out of a possible 9.8 dB). Farfield reductions of 15 dB (SPL) were obtained. The (4,0) and (4,1) modes were reduced simultaneously yielding a 15 dB PWL decrease. The results indicate that global attenuation of PWL at the target frequency was obtained in the aft quadrant using an ANC actuator and sensor system totally contained within the duct. The quality of the results depended on precise mode generation. High spillover into spurious modes generated by the ANC actuator array caused less than optimum levels of PWL reduction. The variation in spillover is believed to be due to calibration procedure, but must be confirmed in subsequent tests.

  19. Active Attenuation of Acoustic Noise Using Adaptive Armax Control.

    NASA Astrophysics Data System (ADS)

    Swanson, David Carl

    An adaptive auxiliary input autoregressive moving average (ARMAX) control system using the recursive least -squares lattice for system identification is developed for active control of dynamic systems. The closed-loop adaptive ARMAX control system is applied to active acoustic noise reduction in three-dimensional spaces. The structure of the ARMAX system is compared to that for duct cancellation systems, model-reference control systems, and the general field solution and is seen as a reasonable approach for active field control in the general case. The ARMAX system is derived for multiple inputs and outputs where the measured outputs are to be driven to desired waveforms with least -squares error using a multi-channel ARMAX lattice for recursive system identification. A significant reduction in complexity is obtained by neglecting the ARMAX zeros for the special case of active attenuation of non-dispersive acoustic waves. It is shown that using the least-squares lattice requires fewer multiplies, divides, additions, and subtractions than the recursive least-squares algorithm which is based on the matrix inversion lemma. Computational complexity is seen as an important issue in the application of adaptive ARMAX systems to active field control because the system must control relatively higher numbers of modes and frequencies in real time than are seen in industrial process plants for which the adaptive ARMAX systems were first developed using recursive least squares. Convergence requirements using the lattice system identification algorithm are the same as that for the recursive least squares algorithm in adaptive ARMAX system and are verified in numerical simulations using known ARMAX parameters. A real-time simulation of active attenuation of acoustic noise is presented using the blade-excited harmonics from a small axial flow fan. The adaptive ARMAX controller provides active attenuation for correlated spectral peaks but not for uncorrelated noise from turbulence

  20. Physical modeling of the feedback path in hearing aids with application to adaptive feedback cancellation

    NASA Astrophysics Data System (ADS)

    Hayes, Joanna L.; Rafaely, Boaz

    2002-05-01

    Hearing aid system modeling based on two-port network theory has been used previously to study the forward gain and the feedback path in hearing aids. The two-port modeling approach is employed in this work to develop an analytic model of the feedback path by reducing the model matrices to simplified analytic expressions. Such an analytic model can simulate the frequency response of the feedback path given the values of relatively few physical parameters such as vent dimensions. The model was extended to include variability in the feedback path due to slit leaks, for example. The analytic model was then incorporated in an adaptive feedback cancellation system, where the physical parameters of the model were adapted to match the actual feedback path and cancel the feedback signal. In the initial stage of this study, the ability of the model to match the frequency response of various measured feedback paths was studied using numerical optimization. Then, an adaptive filtering configuration based on the physical model was developed and studied using computer simulations. Results show that this new approach to adaptive feedback cancellation has the potential to improve both adaptation speed and performance robustness.

  1. Measurement of ultra-low power oscillators using adaptive drift cancellation with applications to nano-magnetic spin torque oscillators.

    PubMed

    Tamaru, S; Ricketts, D S

    2013-05-01

    This work presents a technique for measuring ultra-low power oscillator signals using an adaptive drift cancellation method. We demonstrate this technique through spectrum measurements of a sub-pW nano-magnet spin torque oscillator (STO). We first present a detailed noise analysis of the standard STO characterization apparatus to estimate the background noise level, then compare these results to the noise level of three measurement configurations. The first and second share the standard configuration but use different spectrum analyzers (SA), an older model and a state-of-the-art model, respectively. The third is the technique proposed in this work using the same old SA as for the first. Our results show that the first and second configurations suffer from a large drift that requires ~30 min to stabilize each time the SA changes the frequency band, even though the SA has been powered on for longer than 24 h. The third configuration introduced in this work, however, shows absolutely no drift as the SA changes frequency band, and nearly the same noise performance as with a state-of-the-art SA, thus providing a reliable method for measuring very low power signals for a wide variety of applications. PMID:23742572

  2. Array model interpolation and subband iterative adaptive filters applied to beamforming-based acoustic echo cancellation.

    PubMed

    Bai, Mingsian R; Chi, Li-Wen; Liang, Li-Huang; Lo, Yi-Yang

    2016-02-01

    In this paper, an evolutionary exposition is given in regard to the enhancing strategies for acoustic echo cancellers (AECs). A fixed beamformer (FBF) is utilized to focus on the near-end speaker while suppressing the echo from the far end. In reality, the array steering vector could differ considerably from the ideal freefield plane wave model. Therefore, an experimental procedure is developed to interpolate a practical array model from the measured frequency responses. Subband (SB) filtering with polyphase implementation is exploited to accelerate the cancellation process. Generalized sidelobe canceller (GSC) composed of an FBF and an adaptive blocking module is combined with AEC to maximize cancellation performance. Another enhancement is an internal iteration (IIT) procedure that enables efficient convergence in the adaptive SB filters within a sample time. Objective tests in terms of echo return loss enhancement (ERLE), perceptual evaluation of speech quality (PESQ), word recognition rate for automatic speech recognition (ASR), and subjective listening tests are conducted to validate the proposed AEC approaches. The results show that the GSC-SB-AEC-IIT approach has attained the highest ERLE without speech quality degradation, even in double-talk scenarios. PMID:26936567

  3. Reducing the Effects of Background Noise during Auditory Functional Magnetic Resonance Imaging of Speech Processing: Qualitative and Quantitative Comparisons between Two Image Acquisition Schemes and Noise Cancellation

    ERIC Educational Resources Information Center

    Blackman, Graham A.; Hall, Deborah A.

    2011-01-01

    Purpose: The intense sound generated during functional magnetic resonance imaging (fMRI) complicates studies of speech and hearing. This experiment evaluated the benefits of using active noise cancellation (ANC), which attenuates the level of the scanner sound at the participant's ear by up to 35 dB around the peak at 600 Hz. Method: Speech and…

  4. Adaptive singular value cancelation of ventricular activity in single-lead atrial fibrillation electrocardiograms.

    PubMed

    Alcaraz, Raúl; Rieta, José Joaquín

    2008-12-01

    The proper analysis and characterization of atrial fibrillation (AF) from surface electrocardiographic (ECG) recordings requires to cancel out the ventricular activity (VA), which is composed of the QRS complex and the T wave. Historically, for single-lead ECGs, the averaged beat subtraction (ABS) has been the most widely used technique. However, this method is very sensitive to QRST wave variations and, moreover, high-quality cancelation templates may be difficult to obtain when only short length and single-lead recordings are available. In order to overcome these limitations, a new QRST cancelation method based on adaptive singular value cancelation (ASVC) applied to each single beat is proposed. In addition, an exhaustive study about the optimal set of complexes for better cancelation of every beat is also presented for the first time. The whole study has been carried out with both simulated and real AF signals. For simulated AF, the cancelation performance was evaluated making use of a cross-correlation index and the normalized mean square error (nmse) between the estimated and the original atrial activity (AA). For real AF signals, two additional new parameters were proposed. First, the ventricular residue (VR) index estimated the presence of ventricular activity in the extracted AA. Second, the similarity (S) evaluated how the algorithm preserved the AA segments out of the QRST interval. Results indicated that for simulated AF signals, mean correlation, nmse, VR and S values were 0.945 +/- 0.024, 0.332 +/- 0.073, 1.552 +/- 0.386 and 0.986 +/- 0.012, respectively, for the ASVC method and 0.866 +/- 0.042, 0.424 +/- 0.120, 2.161 +/- 0.564 and 0.922 +/- 0.051 for ABS. In the case of real signals, the mean VR and S values were 1.725 +/- 0.826 and 0.983 +/- 0.038, respectively, for ASVC and 3.159 +/- 1.097 and 0.951 +/- 0.049 for ABS. Thus, ASVC provides a more accurate beat-to-beat ventricular QRST representation than traditional techniques. As a consequence, VA

  5. Active noise control using noise source having adaptive resonant frequency tuning through stiffness variation

    NASA Technical Reports Server (NTRS)

    Pla, Frederic G. (Inventor); Rajiyah, Harindra (Inventor); Renshaw, Anthony A. (Inventor); Hedeen, Robert A. (Inventor)

    1995-01-01

    A noise source for an aircraft engine active noise cancellation system in which the resonant frequency of a noise radiating element is tuned to permit noise cancellation over a wide range of frequencies. The resonant frequency of the noise radiating element is tuned by a plurality of force transmitting mechanisms which contact the noise radiating element. Each one of the force transmitting mechanisms includes an expandable element and a spring in contact with the noise radiating element so that excitation of the element varies the spring force applied to the noise radiating element. The elements are actuated by a controller which receives input of a signal proportional to displacement of the noise radiating element and a signal corresponding to the blade passage frequency of the engine's fan. In response, the controller determines a control signal which is sent to the elements and causes the spring force applied to the noise radiating element to be varied. The force transmitting mechanisms can be arranged to either produce bending or linear stiffness variations in the noise radiating element.

  6. Modeling and adaptive control of acoustic noise

    NASA Astrophysics Data System (ADS)

    Venugopal, Ravinder

    Active noise control is a problem that receives significant attention in many areas including aerospace and manufacturing. The advent of inexpensive high performance processors has made it possible to implement real-time control algorithms to effect active noise control. Both fixed-gain and adaptive methods may be used to design controllers for this problem. For fixed-gain methods, it is necessary to obtain a mathematical model of the system to design controllers. In addition, models help us gain phenomenological insights into the dynamics of the system. Models are also necessary to perform numerical simulations. However, models are often inadequate for the purpose of controller design because they involve parameters that are difficult to determine and also because there are always unmodeled effects. This fact motivates the use of adaptive algorithms for control since adaptive methods usually require significantly less model information than fixed-gain methods. The first part of this dissertation deals with derivation of a state space model of a one-dimensional acoustic duct. Two types of actuation, namely, a side-mounted speaker (interior control) and an end-mounted speaker (boundary control) are considered. The techniques used to derive the model of the acoustic duct are extended to the problem of fluid surface wave control. A state space model of small amplitude surfaces waves of a fluid in a rectangular container is derived and two types of control methods, namely, surface pressure control and map actuator based control are proposed and analyzed. The second part of this dissertation deals with the development of an adaptive disturbance rejection algorithm that is applied to the problem of active noise control. ARMARKOV models which have the same structure as predictor models are used for system representation. The algorithm requires knowledge of only one path of the system, from control to performance, and does not require a measurement of the disturbance nor

  7. Robust local search for spacecraft operations using adaptive noise

    NASA Technical Reports Server (NTRS)

    Fukunaga, Alex S.; Rabideau, Gregg; Chien, Steve

    2004-01-01

    Randomization is a standard technique for improving the performance of local search algorithms for constraint satisfaction. However, it is well-known that local search algorithms are constraints satisfaction. However, it is well-known that local search algorithms are to the noise values selected. We investigate the use of an adaptive noise mechanism in an iterative repair-based planner/scheduler for spacecraft operations. Preliminary results indicate that adaptive noise makes the use of randomized repair moves safe and robust; that is, using adaptive noise makes it possible to consistently achieve, performance comparable with the best tuned noise setting without the need for manually tuning the noise parameter.

  8. Active noise control using noise source having adaptive resonant frequency tuning through stress variation

    NASA Technical Reports Server (NTRS)

    Pla, Frederic G. (Inventor); Rajiyah, Harindra (Inventor); Renshaw, Anthony A. (Inventor); Hedeen, Robert A. (Inventor)

    1995-01-01

    A noise source for an aircraft engine active noise cancellation system in which the resonant frequency of a noise radiating element is tuned to permit noise cancellation over a wide range of frequencies. The resonant frequency of the noise radiating element is tuned by an expandable ring embedded in the noise radiating element. Excitation of the ring causes expansion or contraction of the ring, thereby varying the stress in the noise radiating element. The ring is actuated by a controller which receives input of a feedback signal proportional to displacement of the noise radiating element and a signal corresponding to the blade passage frequency of the engine's fan. In response, the controller determines a control signal which is sent to the ring, causing the ring to expand or contract. Instead of a single ring embedded in the noise radiating panel, a first expandable ring can be bonded to one side of the noise radiating element, and a second expandable ring can be bonded to the other side.

  9. Carbon Nanotube Thin Films for Active Noise Cancellation, Solar Energy Harvesting, and Energy Storage in Building Windows

    NASA Astrophysics Data System (ADS)

    Hu, Shan

    This research explores the application of carbon nanotube (CNT) films for active noise cancellation, solar energy harvesting and energy storage in building windows. The CNT-based components developed herein can be integrated into a solar-powered active noise control system for a building window. First, the use of a transparent acoustic transducer as both an invisible speaker for auxiliary audio playback and for active noise cancellation is accomplished in this work. Several challenges related to active noise cancellation in the window are addressed. These include secondary path estimation and directional cancellation of noise so as to preserve auxiliary audio and internal sounds while preventing transmission of external noise into the building. Solar energy can be harvested at a low rate of power over long durations while acoustic sound cancellation requires short durations of high power. A supercapacitor based energy storage system is therefore considered for the window. Using CNTs as electrode materials, two generations of flexible, thin, and fully solid-state supercapacitors are developed that can be integrated into the window frame. Both generations consist of carbon nanotube films coated on supporting substrates as electrodes and a solid-state polymer gel layer for the electrolyte. The first generation is a single-cell parallel-plate supercapacitor with a working voltage of 3 Volts. Its energy density is competitive with commercially available supercapacitors (which use liquid electrolyte). For many applications that will require higher working voltage, the second-generation multi-cell supercapacitor is developed. A six-cell device with a working voltage as high as 12 Volts is demonstrated here. Unlike the first generation's 3D structure, the second generation has a novel planar (2D) architecture, which makes it easy to integrate multiple cells into a thin and flexible supercapacitor. The multi-cell planar supercapacitor has energy density exceeding that of

  10. Phase noise tolerant inter-carrier-interference cancellation for WDM superchannels with sub-Nyquist channel spacing.

    PubMed

    Yao, Shuchang; Fu, Songnian; Li, Jianqiang; Tang, Ming; Shum, Perry; Liu, Deming

    2013-09-01

    We propose and demonstrate a novel multi-input multi-output (MIMO) equalization based inter-carrier-interference (ICI) cancellation approach employing constant modulus algorithm (CMA) for supperchanels with sub-Nyquist channel spacing, where optical combs are used as optical sources. Compared with the least mean square (LMS) algorithm based ICI canceller, the proposed approach has comparable capability to accomplish the ICI mitigation for 56 Gbaud dual-polarization quadrature phase shift keying (DP-QPSK) signals with tight channel spacing till 50 GHz. In particular, compared with the LMS-MIMO based ICI canceller, the optical linewidth tolerance of 6 MHz is relaxed to 20 MHz given a 1dB required optical signal-to-noise ratio (OSNR) penalty for the CMA-MIMO based ICI canceller. Meanwhile, the CMA-MIMO based ICI canceller is ideal for real-time processing, since the number of parallel processing pipelines can be greater than 240 even in the presence of large linewidth.

  11. Active Control of Fan Noise-Feasibility Study. Volume 2: Canceling Noise Source-Design of an Acoustic Plate Radiator Using Piezoceramic Actuators

    NASA Technical Reports Server (NTRS)

    Pla, F. G.; Rajiyah, H.

    1995-01-01

    The feasibility of using acoustic plate radiators powered by piezoceramic thin sheets as canceling sources for active control of aircraft engine fan noise is demonstrated. Analytical and numerical models of actuated beams and plates are developed and validated. An optimization study is performed to identify the optimum combination of design parameters that maximizes the plate volume velocity for a given resonance frequency. Fifteen plates with various plate and actuator sizes, thicknesses, and bonding layers were fabricated and tested using results from the optimization study. A maximum equivalent piston displacement of 0.39 mm was achieved with the optimized plate samples tested with only one actuator powered, corresponding to a plate deflection at the center of over 1 millimeter. This is very close to the deflection required for a full size engine application and represents a 160-fold improvement over previous work. Experimental results further show that performance is limited by the critical stress of the piezoceramic actuator and bonding layer rather than by the maximum moment available from the actuator. Design enhancements are described in detail that will lead to a flight-worthy acoustic plate radiator by minimizing actuator tensile stresses and reducing nonlinear effects. Finally, several adaptive tuning methods designed to increase the bandwidth of acoustic plate radiators are analyzed including passive, active, and semi-active approaches. The back chamber pressurization and volume variation methods are investigated experimentally and shown to be simple and effective ways to obtain substantial control over the resonance frequency of a plate radiator. This study shows that piezoceramic-based plate radiators can be a viable acoustic source for active control of aircraft engine fan noise.

  12. Noise cancellation model validation for reduced motion artifact wearable PPG sensors using MEMS accelerometers.

    PubMed

    Wood, Levi B; Asada, H Harry

    2006-01-01

    This paper investigates the validity of utilizing Widrow's Active Noise Cancellation (ANC) in the context of motion artifact reduction for photoplethysmogram (PPG) sensors. The ANC approach has previously been applied to the PPG problem, but little consideration has been given to the validity of the ANC signal corruption assumptions and in what motion range the algorithm works. The ANC validity testing is done in the form of impact (approximate impulse) testing of the physical PPG system and comparing with the modeled response for a range of motion amplitudes. The testing reveals that the identified corruption model does not generally represent the true physical system, but locally approximates the true system. Testing shows that if a similar motion amplitude is used for model tuning as the impact test, an average peak deviation of 5.2% is obtained, but if motion amplitude that is smaller than the impact amplitude by a factor of 5, the peak deviation is 15%. Finally, after ANC filtering motion corrupted data, heart rate can be estimated with less than 1.6% error.

  13. Active vibration control on a quarter-car for cancellation of road noise disturbance

    NASA Astrophysics Data System (ADS)

    Belgacem, Walid; Berry, Alain; Masson, Patrice

    2012-07-01

    In this paper, a methodology is presented for the cancellation of road noise, from the analysis of vibration transmission paths for an automotive suspension to the design of an active control system using inertial actuators on a suspension to reduce the vibrations transmitted to the chassis. First, experiments were conducted on a Chevrolet Epica LS automobile on a concrete test track to measure accelerations induced on the suspension by the road. These measurements were combined with experimental Frequency Response Functions (FRFs) measured on a quarter-car test bench to reconstruct an equivalent three dimensional force applied on the wheel hub. Second, FRFs measured on the test bench between the three-dimensional driving force and forces at each suspension/chassis linkage were used to characterize the different transmission paths of vibration energy to the chassis. Third, an experimental model of the suspension was constructed to simulate the configuration of the active control system, using the primary (disturbance) FRFs and secondary (control) FRFs also measured on the test bench. This model was used to optimize the configuration of the control actuators and to evaluate the required forces. Finally, a prototype of an active suspension was implemented and measurements were performed in order to assess the performance of the control approach. A 4.6 dB attenuation on transmitted forces was obtained in the 50-250 Hz range.

  14. Active noise control using noise source having adaptive resonant frequency tuning through variable ring loading

    NASA Technical Reports Server (NTRS)

    Pla, Frederic G. (Inventor); Rajiyah, Harindra (Inventor); Renshaw, Anthony A. (Inventor); Hedeen, Robert A. (Inventor)

    1995-01-01

    A noise source for an aircraft engine active noise cancellation system in which the resonant frequency of noise radiating structure is tuned to permit noise cancellation over a wide range of frequencies. The resonant frequency of the noise radiating structure is tuned by a plurality of drivers arranged to contact the noise radiating structure. Excitation of the drivers causes expansion or contraction of the drivers, thereby varying the edge loading applied to the noise radiating structure. The drivers are actuated by a controller which receives input of a feedback signal proportional to displacement of the noise radiating element and a signal corresponding to the blade passage frequency of the engine's fan. In response, the controller determines a control signal which is sent to the drivers, causing them to expand or contract. The noise radiating structure may be either the outer shroud of the engine or a ring mounted flush with an inner wall of the shroud or disposed in the interior of the shroud.

  15. Application of Noise Cancelling and Damage Detection Algorithms in NDE of Concrete Bridge Decks Using Impact Signals

    SciTech Connect

    Zhang, Gang; Harichandran, Ronald S.; Ramuhalli, Pradeep

    2011-09-13

    Delamination is a commonly observed distress in concrete bridge decks. Among all the delamination detection methods, acoustic methods have the advantages of being fast and inexpensive. In traditional acoustic inspection methods, the inspector drags a chain along or hammers on the bridge deck and detects delamination from the 'hollowness' of the sounds. The signals are often contaminated by ambient traffic noise and the detection of delamination is highly subjective. This paper describes the performance of an impact-bases acoustic NDE method where the traffic noise was filtered by employing a noise cancelling algorithm and where subjectivity was eliminated by introducing feature extraction and pattern recognition algorithms. Different algorithms were compared and the best one was selected in each category. The comparison showed that the modified independent component analysis (ICA) algorithm was most effective in cancelling the traffic noise and features consisting of mel-frequency cepstral coefficients (MFCCs) had the best performance in terms of repeatability and separabillty. The condition of the bridge deck was then detected by a radial basis function (RBF) neural network. The performance of the system was evaluated using both experimental and field data. The results show that the selected algorithms increase the noise robustness of acoustic methods and perform satisfactorily if the training data is representative.

  16. The effect on recognition memory of noise cancelling headphones in a noisy environment with native and non-native speakers.

    PubMed

    Molesworth, Brett R C; Burgess, Marion; Gunnell, Belinda; Löffler, Diana; Venjakob, Antje

    2014-01-01

    Noise has the potential to impair cognitive performance. For nonnative speakers, the effect of noise on performance is more severe than their native counterparts. What remains unknown is the effectiveness of countermeasures such as noise attenuating devices in such circumstances. Therefore, the main aim of the present research was to examine the effectiveness of active noise attenuating countermeasures in the presence of simulated aircraft noise for both native and nonnative English speakers. Thirty-two participants, half native English speakers and half native German speakers completed four recognition (cued) recall tasks presented in English under four different audio conditions, all in the presence of simulated aircraft noise. The results of the research indicated that in simulated aircraft noise at 65 dB(A), performance of nonnative English speakers was poorer than for native English speakers. The beneficial effects of noise cancelling headphones in improving the signal to noise ratio led to an improved performance for nonnative speakers. These results have particular importance for organizations operating in a safety-critical environment such as aviation. PMID:25033791

  17. The effect on recognition memory of noise cancelling headphones in a noisy environment with native and non-native speakers.

    PubMed

    Molesworth, Brett R C; Burgess, Marion; Gunnell, Belinda; Löffler, Diana; Venjakob, Antje

    2014-01-01

    Noise has the potential to impair cognitive performance. For nonnative speakers, the effect of noise on performance is more severe than their native counterparts. What remains unknown is the effectiveness of countermeasures such as noise attenuating devices in such circumstances. Therefore, the main aim of the present research was to examine the effectiveness of active noise attenuating countermeasures in the presence of simulated aircraft noise for both native and nonnative English speakers. Thirty-two participants, half native English speakers and half native German speakers completed four recognition (cued) recall tasks presented in English under four different audio conditions, all in the presence of simulated aircraft noise. The results of the research indicated that in simulated aircraft noise at 65 dB(A), performance of nonnative English speakers was poorer than for native English speakers. The beneficial effects of noise cancelling headphones in improving the signal to noise ratio led to an improved performance for nonnative speakers. These results have particular importance for organizations operating in a safety-critical environment such as aviation.

  18. The effect of losses on the quantum-noise cancellation in the SU(1,1) interferometer

    NASA Astrophysics Data System (ADS)

    Xin, Jun; Wang, Hailong; Jing, Jietai

    2016-08-01

    Quantum-noise cancellation (QNC) is an effective method to control the noise of the quantum system, which reduces or even eliminates the noise of the quantum systems by utilizing destructive interference in the quantum system. However, QNC can be extremely dependent on the losses inside the system. In this letter, we experimentally and theoretically study how the losses can affect the QNC in the SU(1,1) interferometer. We find that losses in the different arms inside the SU(1,1) interferometer can have different effects on the QNC in the output fields from the SU(1,1) interferometer. And the QNC in the SU(1,1) interferometer can almost be insensitive to the losses in some cases. Our findings may find its potential applications in the quantum noise control.

  19. Adaptive Interference Cancelation using a Pair of Magnetometers for Small Satellite Applications: No Need for a Boom

    NASA Astrophysics Data System (ADS)

    Moldwin, M.; Sheinker, A.

    2015-12-01

    We have developed a new method for adaptively canceling a magnetic interference using a pair of magnetometers, which is especially effective for a time-varying interference with an unknown signature. By canceling the interference, the method enables the recovery of the ambient geomagnetic field. Computer simulations and experiments with real-world data validate the theoretical analysis, and thereby, pave the way for magnetic measurements in orbit using boomless CubeSats.

  20. SVD-Based Technique for Interference Cancellation and Noise Reduction in NMR Measurement of Time-Dependent Magnetic Fields.

    PubMed

    Chen, Wenjun; Ma, Hong; Yu, De; Zhang, Hua

    2016-03-04

    A nuclear magnetic resonance (NMR) experiment for measurement of time-dependent magnetic fields was introduced. To improve the signal-to-interference-plus-noise ratio (SINR) of NMR data, a new method for interference cancellation and noise reduction (ICNR) based on singular value decomposition (SVD) was proposed. The singular values corresponding to the radio frequency interference (RFI) signal were identified in terms of the correlation between the FID data and the reference data, and then the RFI and noise were suppressed by setting the corresponding singular values to zero. The validity of the algorithm was verified by processing the measured NMR data. The results indicated that, this method has a significantly suppression of RFI and random noise, and can well preserve the FID signal. At present, the major limitation of the proposed SVD-based ICNR technique is that the threshold value for interference cancellation needs to be manually selected. Finally, the inversion waveform of the applied alternating magnetic field was given by fitting the processed experimental data.

  1. SVD-Based Technique for Interference Cancellation and Noise Reduction in NMR Measurement of Time-Dependent Magnetic Fields

    PubMed Central

    Chen, Wenjun; Ma, Hong; Yu, De; Zhang, Hua

    2016-01-01

    A nuclear magnetic resonance (NMR) experiment for measurement of time-dependent magnetic fields was introduced. To improve the signal-to-interference-plus-noise ratio (SINR) of NMR data, a new method for interference cancellation and noise reduction (ICNR) based on singular value decomposition (SVD) was proposed. The singular values corresponding to the radio frequency interference (RFI) signal were identified in terms of the correlation between the FID data and the reference data, and then the RFI and noise were suppressed by setting the corresponding singular values to zero. The validity of the algorithm was verified by processing the measured NMR data. The results indicated that, this method has a significantly suppression of RFI and random noise, and can well preserve the FID signal. At present, the major limitation of the proposed SVD-based ICNR technique is that the threshold value for interference cancellation needs to be manually selected. Finally, the inversion waveform of the applied alternating magnetic field was given by fitting the processed experimental data. PMID:26959024

  2. Adaptive cancellation of variable feedback path for hearing aid using misalignment-dependent step size values.

    PubMed

    Khoubrouy, Soudeh A; Panahi, Issa M S

    2011-01-01

    Various methods have been proposed to overcome the problem of compensating the acoustic feedback path that negatively impacts the performance of hearing aid devices. However, in most of them feedback path model is assumed to be fixed which is not quite realistic. In this paper, we consider fixed and variable feedback paths and analyze for each case the performance of one of the robust Adaptive Feedback Cancellation (AFC) schemes, i.e. the Prediction Error Method AFC which uses Partitioned Block Frequency-Domain Normalized Least Mean Square (PBFD-NLMS) algorithm. Based on the analysis results we propose varying the step size values for the same adaptive algorithm on the fly by monitoring the misalignment criteria. The experimental results using the proposed method show improvement made on the system performance. PMID:22256175

  3. Adaptation of Cancellous Bone to Aging and Immobilization in Growing Rats

    NASA Technical Reports Server (NTRS)

    Chen, Meng Meng; Jee, Webster S. S.; Ke, Hua Zhu; Lin, Bia Yun; Li, Qing Nan; Li, Xiao Jian

    1992-01-01

    Two-and-a half month-old female rats were subjected to right hindlimb immobilization or served as controls for 0, 1, 2, 8, 14, and 20 weeks. The right hindlimb was immobilized by bandaging it against the abdomen, thus unloading it. Cancellous bone histomorphometry was performed on microradiographs and double-fluorescent labeled 20 micron sections of the distal femoral metaphyses. Primary spongiosa bone loss occurred rapidly by 2 weeks, and secondary spongiosa bone loss occurred rapidly by 8 weeks of immobilization, and then equilibrated at 60% less bone mass than age-related controls. The negative bone balance induced by immobilization was caused by transient increase in bone resorption, decrease in bone formation, and longitudinal bone growth. The dynamic data of secondary spongiosa cancellous bone showed that percent eroded perimeter was transiently elevated by 55% to 82% between 1 and 8 weeks, percent labeled perimeter was transiently depressed by 32% to 50% between 1 and 14 weeks, mineral apposition rate was depressed by 23% and 19% at 1 and 2 weeks, and bone formation rate-bone area referent was transiently depressed by 35% and 59%c at 1 and 2 weeks. All the above parameters were at age-related control levels by 20 weeks of immobilization. However, bone formation rate-tissue area referent was depressed (-65%) throughout the study. Immobilization depressed completely longitudinal bone growth by 2 weeks and remained so. Only 0.65 mm of new metaphysis was generated in the immobilized versus 2.1 mm in controls during the study period. The immobilization induced an early cancellous bone loss which equilibrated at a new steady state with less bone and a normal (age-related control) bone turnover rate. When these findings were compared to an earlier study of 9 month-old virgin females subjected to right hindlimb immobilization up to 26 weeks, we found the adaptive responses of the cancellous bone were identical except that they occurred earlier and equilibrated

  4. Adaptation of Cancellous Bone to Aging and Immobilization in Growing Rats

    NASA Technical Reports Server (NTRS)

    Chen, Meng-Meng; Jee, Webster S. S.; Ke, Hua-Zhu; Lin, Bai-Yun; Li, Qing-Nan; Li, Xiao-Jian

    1992-01-01

    Two-and-half-month-old female rats were subjected to right hindlimb immobilization or served as controls for 0, 1, 2, 8, 14, and 20 weeks. The right hindlimb was immobilized by bandaging it against the abdomen, thus unloading it. Cancellous bone histomorphometry was performed on microradiographs and double-fluorescent labeled 20 tLm sections of the distal femoral metaphyses. Primary spongiosa bone loss occurred rapidly by 2 weeks, and secondary spongiosa bone loss occurred rapidly by 8 weeks of immobilization, and then equilibrated at 60% less bone mass than age-related controls. The negative bone balance induced by immobilization was caused by transient increase in bone resorption, decrease in bone formation, and longitudinal bone growth. The dynamic data of secondary spongiosa cancellous bone showed that percent eroded perimeter was transiently elevated by 55 to 82% between 1 and 8 weeks, percent labeled perimeter was transiently depressed by 32% to 50% between 1 and 14 weeks, mineral apposition rate was depressed by 23% and 19% at I and 2 weeks, and bone formation rate-bone area referent was transiently depressed by 35% and 59% at 1 and 2 weeks. All the above parameters were at age-related control levels by 20 weeks of immobiliza- tion. However, bone formation rate-tissue area referent was depressed (-65%) throughout the study. Immobilization depressed completely longitudinal bone growth by 2 weeks and remained so. Only 0.65 mm of new metaphysis was generated in the immobilized versus 2.1 mm in controls during the study period. The immobilization induced an early cancellous bone loss which equilibrated at a new steady state with less bone and a normal (age-related control) bone turnover rate. When these findings were compared to an earlier study of 9-month-old virgin females subjected to right hindlimb immobilization up to 26 weeks, we found the adaptive responses of the cancellous bone were identical except that they occurred earlier and equilibrated sooner in

  5. Neuromorphic learning of continuous-valued mappings in the presence of noise: Application to real-time adaptive control

    NASA Technical Reports Server (NTRS)

    Troudet, Terry; Merrill, Walter C.

    1989-01-01

    The ability of feed-forward neural net architectures to learn continuous-valued mappings in the presence of noise is demonstrated in relation to parameter identification and real-time adaptive control applications. Factors and parameters influencing the learning performance of such nets in the presence of noise are identified. Their effects are discussed through a computer simulation of the Back-Error-Propagation algorithm by taking the example of the cart-pole system controlled by a nonlinear control law. Adequate sampling of the state space is found to be essential for canceling the effect of the statistical fluctuations and allowing learning to take place.

  6. Adaptive noise reduction circuit for a sound reproduction system

    NASA Technical Reports Server (NTRS)

    Engebretson, A. Maynard (Inventor); O'Connell, Michael P. (Inventor)

    1995-01-01

    A noise reduction circuit for a hearing aid having an adaptive filter for producing a signal which estimates the noise components present in an input signal. The circuit includes a second filter for receiving the noise-estimating signal and modifying it as a function of a user's preference or as a function of an expected noise environment. The circuit also includes a gain control for adjusting the magnitude of the modified noise-estimating signal, thereby allowing for the adjustment of the magnitude of the circuit response. The circuit also includes a signal combiner for combining the input signal with the adjusted noise-estimating signal to produce a noise reduced output signal.

  7. Adaptive whitening of ambient ocean noise with narrowband signal preservation.

    PubMed

    Hollmann, Luke J; Stevenson, Robert L

    2016-06-01

    Passive underwater listening devices are often deployed to listen for narrowband signals of interest in time-varying background ocean noise. Such tonals are generated mechanically by ships, submarines, and machines, or acoustically by aquatic wildlife. Quantization of the sensor data for storage or low bit-rate transmission adds white noise which can overwhelm weak narrowband signals if the background noise is sufficiently colored. Whitening the background noise prior to quantization can reduce the detrimental effects, but the whitening process must preserve any tonals in the signal for maximum effectiveness. Existing adaptive whitening techniques make no effort to avoid suppressing tonals in the whitening process, while existing spectral separation methods fail to whiten background noise. The proposed methods perform adaptive whitening of background ambient noise while preserving narrowband tones at their original signal-to-noise ratios. The proposed methods are shown to outperform combinations of existing partial solutions both subjectively and by evaluating the objective criteria introduced. The stability and convergence properties of the proposed algorithms match or surpass those of existing well-known adaptive algorithms. PMID:27369136

  8. Robust stochastic resonance: Signal detection and adaptation in impulsive noise

    NASA Astrophysics Data System (ADS)

    Kosko, Bart; Mitaim, Sanya

    2001-11-01

    Stochastic resonance (SR) occurs when noise improves a system performance measure such as a spectral signal-to-noise ratio or a cross-correlation measure. All SR studies have assumed that the forcing noise has finite variance. Most have further assumed that the noise is Gaussian. We show that SR still occurs for the more general case of impulsive or infinite-variance noise. The SR effect fades as the noise grows more impulsive. We study this fading effect on the family of symmetric α-stable bell curves that includes the Gaussian bell curve as a special case. These bell curves have thicker tails as the parameter α falls from 2 (the Gaussian case) to 1 (the Cauchy case) to even lower values. Thicker tails create more frequent and more violent noise impulses. The main feedback and feedforward models in the SR literature show this fading SR effect for periodic forcing signals when we plot either the signal-to-noise ratio or a signal correlation measure against the dispersion of the α-stable noise. Linear regression shows that an exponential law γopt(α)=cAα describes this relation between the impulsive index α and the SR-optimal noise dispersion γopt. The results show that SR is robust against noise ``outliers.'' So SR may be more widespread in nature than previously believed. Such robustness also favors the use of SR in engineering systems. We further show that an adaptive system can learn the optimal noise dispersion for two standard SR models (the quartic bistable model and the FitzHugh-Nagumo neuron model) for the signal-to-noise ratio performance measure. This also favors practical applications of SR and suggests that evolution may have tuned the noise-sensitive parameters of biological systems.

  9. Channel capacity of an array system for Gaussian channels with applications to combining and noise cancellation

    NASA Technical Reports Server (NTRS)

    Cheung, K. M.; Vilnrotter, V.

    1996-01-01

    A closed-form expression for the capacity of an array of correlated Gaussian channels is derived. It is shown that when signal and noise are independent, the array of observables can be replaced with a single observable without diminishing the capacity of the array channel. Examples are provided to illustrate the dependence of channel capacity on noise correlation for two- and three-channel arrays.

  10. Common mode noise cancellation for electrically non-contact ECG measurement system on a chair.

    PubMed

    Keun Kim, Ko; Kyu Lim, Yong; Suk Park, Kwang

    2005-01-01

    Electrically non-contact ECG measurement system on a chair can be applied to a number of various fields for continuous health monitoring in daily life. However, the body is floated electrically for this system due to the capacitive electrodes and the floated body is very sensitive to the external noises or motion artifacts which affect the measurement system as the common mode noise. In this paper, the Driven-Seat-Ground circuit similar to the Driven-Right-Leg circuit is proposed to reduce the common mode noise. The analysis of this equivalent circuit is performed and the output signal waveforms are compared between with Driven-Seat-Ground and with capacitive ground. As the results, the Driven-Seat-Ground circuit improves significantly the properties of the fully capacitive ECG measurement system as the negative feedback.

  11. Application of Feedforward Adaptive Active-Noise Control for Reducing Blade Passing Noise in Centrifugal Fans

    NASA Astrophysics Data System (ADS)

    WU, J.-D.; BAI, M. R.

    2001-02-01

    This paper describes two configurations of feedforward adaptive active-noise control (ANC) technique for reducing blade passing noise in centrifugal fans. In one configuration, the control speaker is installed at the cut-off region of the fan, while in the other configuration at the exit duct. The proposed ANC system is based on the filtered-x least-mean-squares (FXLMS) algorithm with multi-sine synthesized reference signal and frequency counting and is implemented by using a digital signal processor (DSP). Experiments are carried out to evaluate the proposed system for reducing the noise at the blade passing frequency (BPF) and its harmonics at various flow speeds. The results of the experiment indicated that the ANC technique is effective in reducing the blade passing noise for two configurations by using the feedforward adaptive control.

  12. Applications of active adaptive noise control to jet engines

    NASA Technical Reports Server (NTRS)

    Shoureshi, Rahmat; Brackney, Larry

    1993-01-01

    During phase 2 research on the application of active noise control to jet engines, the development of multiple-input/multiple-output (MIMO) active adaptive noise control algorithms and acoustic/controls models for turbofan engines were considered. Specific goals for this research phase included: (1) implementation of a MIMO adaptive minimum variance active noise controller; and (2) turbofan engine model development. A minimum variance control law for adaptive active noise control has been developed, simulated, and implemented for single-input/single-output (SISO) systems. Since acoustic systems tend to be distributed, multiple sensors, and actuators are more appropriate. As such, the SISO minimum variance controller was extended to the MIMO case. Simulation and experimental results are presented. A state-space model of a simplified gas turbine engine is developed using the bond graph technique. The model retains important system behavior, yet is of low enough order to be useful for controller design. Expansion of the model to include multiple stages and spools is also discussed.

  13. An environment-adaptive management algorithm for hearing-support devices incorporating listening situation and noise type classifiers.

    PubMed

    Yook, Sunhyun; Nam, Kyoung Won; Kim, Heepyung; Hong, Sung Hwa; Jang, Dong Pyo; Kim, In Young

    2015-04-01

    In order to provide more consistent sound intelligibility for the hearing-impaired person, regardless of environment, it is necessary to adjust the setting of the hearing-support (HS) device to accommodate various environmental circumstances. In this study, a fully automatic HS device management algorithm that can adapt to various environmental situations is proposed; it is composed of a listening-situation classifier, a noise-type classifier, an adaptive noise-reduction algorithm, and a management algorithm that can selectively turn on/off one or more of the three basic algorithms-beamforming, noise-reduction, and feedback cancellation-and can also adjust internal gains and parameters of the wide-dynamic-range compression (WDRC) and noise-reduction (NR) algorithms in accordance with variations in environmental situations. Experimental results demonstrated that the implemented algorithms can classify both listening situation and ambient noise type situations with high accuracies (92.8-96.4% and 90.9-99.4%, respectively), and the gains and parameters of the WDRC and NR algorithms were successfully adjusted according to variations in environmental situation. The average values of signal-to-noise ratio (SNR), frequency-weighted segmental SNR, Perceptual Evaluation of Speech Quality, and mean opinion test scores of 10 normal-hearing volunteers of the adaptive multiband spectral subtraction (MBSS) algorithm were improved by 1.74 dB, 2.11 dB, 0.49, and 0.68, respectively, compared to the conventional fixed-parameter MBSS algorithm. These results indicate that the proposed environment-adaptive management algorithm can be applied to HS devices to improve sound intelligibility for hearing-impaired individuals in various acoustic environments. PMID:25284135

  14. An environment-adaptive management algorithm for hearing-support devices incorporating listening situation and noise type classifiers.

    PubMed

    Yook, Sunhyun; Nam, Kyoung Won; Kim, Heepyung; Hong, Sung Hwa; Jang, Dong Pyo; Kim, In Young

    2015-04-01

    In order to provide more consistent sound intelligibility for the hearing-impaired person, regardless of environment, it is necessary to adjust the setting of the hearing-support (HS) device to accommodate various environmental circumstances. In this study, a fully automatic HS device management algorithm that can adapt to various environmental situations is proposed; it is composed of a listening-situation classifier, a noise-type classifier, an adaptive noise-reduction algorithm, and a management algorithm that can selectively turn on/off one or more of the three basic algorithms-beamforming, noise-reduction, and feedback cancellation-and can also adjust internal gains and parameters of the wide-dynamic-range compression (WDRC) and noise-reduction (NR) algorithms in accordance with variations in environmental situations. Experimental results demonstrated that the implemented algorithms can classify both listening situation and ambient noise type situations with high accuracies (92.8-96.4% and 90.9-99.4%, respectively), and the gains and parameters of the WDRC and NR algorithms were successfully adjusted according to variations in environmental situation. The average values of signal-to-noise ratio (SNR), frequency-weighted segmental SNR, Perceptual Evaluation of Speech Quality, and mean opinion test scores of 10 normal-hearing volunteers of the adaptive multiband spectral subtraction (MBSS) algorithm were improved by 1.74 dB, 2.11 dB, 0.49, and 0.68, respectively, compared to the conventional fixed-parameter MBSS algorithm. These results indicate that the proposed environment-adaptive management algorithm can be applied to HS devices to improve sound intelligibility for hearing-impaired individuals in various acoustic environments.

  15. Qubit quantum-dot sensors: Noise cancellation by coherent backaction, initial slips, and elliptical precession

    NASA Astrophysics Data System (ADS)

    Hell, M.; Wegewijs, M. R.; DiVincenzo, D. P.

    2016-01-01

    We theoretically investigate the backaction of a sensor quantum dot with strong local Coulomb repulsion on the transient dynamics of a qubit that is probed capacitively. We show that the measurement backaction induced by the noise of electron cotunneling through the sensor is surprisingly mitigated by the recently identified coherent backaction [M. Hell, M. R. Wegewijs, and D. P. DiVincenzo, Phys. Rev. B 89, 195405 (2014), 10.1103/PhysRevB.89.195405] arising from quantum fluctuations. This indicates that a sensor with quantized states may be switched off better than naively expected. This renormalization effect is missing in semiclassical stochastic fluctuator models and typically also in Born-Markov approaches, which try to avoid the calculation of the nonstationary, nonequilibrium state of the qubit plus sensor. Technically, we integrate out the current-carrying electrodes to obtain kinetic equations for the joint, nonequilibrium detector-qubit dynamics. We show that the sensor current response, level renormalization, cotunneling broadening, and leading non-Markovian corrections always appear together and cannot be turned off individually in an experiment or ignored theoretically. We analyze the backaction on the reduced qubit state—capturing the full non-Markovian effects imposed by the sensor quantum dot on the qubit—by applying a Liouville-space decomposition into quasistationary and rapidly decaying modes. Importantly, the sensor cannot be eliminated completely even in the simplest high-temperature, weak-measurement limit since the qubit state experiences an initial slip depending on the initial preparation of qubit plus sensor quantum dot. The slip persists over many qubit cycles, i.e., also on the time scale of the qubit decoherence induced by the backaction. A quantum-dot sensor can thus not be modeled as usual as a "black box" without accounting for its dynamical variables; it is part of the quantum circuit. We furthermore find that the Bloch vector

  16. Fast characterization of two ultrasound longitudinal waves in cancellous bone using an adaptive beamforming technique.

    PubMed

    Taki, Hirofumi; Nagatani, Yoshiki; Matsukawa, Mami; Mizuno, Katsunori; Sato, Toru

    2015-04-01

    The received signal in through-transmission ultrasound measurements of cancellous bone consists of two longitudinal waves, called the fast and slow waves. Analysis of these fast and slow waves may reveal characteristics of the cancellous bone that would be good indicators of osteoporosis. Because the two waves often overlap, decomposition of the received signal is an important problem in the characterization of bone quality. This study proposes a fast and accurate decomposition method based on the frequency domain interferometry imaging method with a modified wave transfer function that uses a phase rotation parameter. The proposed method accurately characterized the fast and slow waves in the experimental study, and the residual intensity, which was normalized with respect to the received signal intensity, was less than -20 dB over the bone specimen thickness range from 6 to 15 mm. In the simulation study, the residual intensity was less than -20 dB over the specimen thickness range from 3 to 8 mm. Decomposition of a single received signal takes only 5 s using a laptop personal computer with a single central processing unit. The proposed method has great potential to provide accurate and rapid measurements of indicators of osteoporosis in cancellous bone.

  17. Nonlinear mode decomposition: a noise-robust, adaptive decomposition method.

    PubMed

    Iatsenko, Dmytro; McClintock, Peter V E; Stefanovska, Aneta

    2015-09-01

    The signals emanating from complex systems are usually composed of a mixture of different oscillations which, for a reliable analysis, should be separated from each other and from the inevitable background of noise. Here we introduce an adaptive decomposition tool-nonlinear mode decomposition (NMD)-which decomposes a given signal into a set of physically meaningful oscillations for any wave form, simultaneously removing the noise. NMD is based on the powerful combination of time-frequency analysis techniques-which, together with the adaptive choice of their parameters, make it extremely noise robust-and surrogate data tests used to identify interdependent oscillations and to distinguish deterministic from random activity. We illustrate the application of NMD to both simulated and real signals and demonstrate its qualitative and quantitative superiority over other approaches, such as (ensemble) empirical mode decomposition, Karhunen-Loève expansion, and independent component analysis. We point out that NMD is likely to be applicable and useful in many different areas of research, such as geophysics, finance, and the life sciences. The necessary matlab codes for running NMD are freely available for download.

  18. Adaptive bilateral filter for sharpness enhancement and noise removal.

    PubMed

    Zhang, Buyue; Allebach, Jan P

    2008-05-01

    In this paper, we present the adaptive bilateral filter (ABF) for sharpness enhancement and noise removal. The ABF sharpens an image by increasing the slope of the edges without producing overshoot or undershoot. It is an approach to sharpness enhancement that is fundamentally different from the unsharp mask (USM). This new approach to slope restoration also differs significantly from previous slope restoration algorithms in that the ABF does not involve detection of edges or their orientation, or extraction of edge profiles. In the ABF, the edge slope is enhanced by transforming the histogram via a range filter with adaptive offset and width. The ABF is able to smooth the noise, while enhancing edges and textures in the image. The parameters of the ABF are optimized with a training procedure. ABF restored images are significantly sharper than those restored by the bilateral filter. Compared with an USM based sharpening method-the optimal unsharp mask (OUM), ABF restored edges are as sharp as those rendered by the OUM, but without the halo artifacts that appear in the OUM restored image. In terms of noise removal, ABF also outperforms the bilateral filter and the OUM. We demonstrate that ABF works well for both natural images and text images. PMID:18390373

  19. Nonlinear mode decomposition: A noise-robust, adaptive decomposition method

    NASA Astrophysics Data System (ADS)

    Iatsenko, Dmytro; McClintock, Peter V. E.; Stefanovska, Aneta

    2015-09-01

    The signals emanating from complex systems are usually composed of a mixture of different oscillations which, for a reliable analysis, should be separated from each other and from the inevitable background of noise. Here we introduce an adaptive decomposition tool—nonlinear mode decomposition (NMD)—which decomposes a given signal into a set of physically meaningful oscillations for any wave form, simultaneously removing the noise. NMD is based on the powerful combination of time-frequency analysis techniques—which, together with the adaptive choice of their parameters, make it extremely noise robust—and surrogate data tests used to identify interdependent oscillations and to distinguish deterministic from random activity. We illustrate the application of NMD to both simulated and real signals and demonstrate its qualitative and quantitative superiority over other approaches, such as (ensemble) empirical mode decomposition, Karhunen-Loève expansion, and independent component analysis. We point out that NMD is likely to be applicable and useful in many different areas of research, such as geophysics, finance, and the life sciences. The necessary matlab codes for running NMD are freely available for download.

  20. Nonlinear mode decomposition: a noise-robust, adaptive decomposition method.

    PubMed

    Iatsenko, Dmytro; McClintock, Peter V E; Stefanovska, Aneta

    2015-09-01

    The signals emanating from complex systems are usually composed of a mixture of different oscillations which, for a reliable analysis, should be separated from each other and from the inevitable background of noise. Here we introduce an adaptive decomposition tool-nonlinear mode decomposition (NMD)-which decomposes a given signal into a set of physically meaningful oscillations for any wave form, simultaneously removing the noise. NMD is based on the powerful combination of time-frequency analysis techniques-which, together with the adaptive choice of their parameters, make it extremely noise robust-and surrogate data tests used to identify interdependent oscillations and to distinguish deterministic from random activity. We illustrate the application of NMD to both simulated and real signals and demonstrate its qualitative and quantitative superiority over other approaches, such as (ensemble) empirical mode decomposition, Karhunen-Loève expansion, and independent component analysis. We point out that NMD is likely to be applicable and useful in many different areas of research, such as geophysics, finance, and the life sciences. The necessary matlab codes for running NMD are freely available for download. PMID:26465549

  1. Active control of environmental noise, VIII: increasing the response to primary source changes including unpredictable noise

    NASA Astrophysics Data System (ADS)

    Wright, S. E.; Atmoko, H.; Vuksanovic, B.

    2004-07-01

    Conventional adaptive cancellation systems using traditional transverse finite impulse response (FIR) filters, together with least mean square (LMS) adaptive algorithms, well known in active noise control, are slow to adapt to primary source changes. This makes them inappropriate for cancelling rapidly changing noise, including unpredictable noise such as speech and music. Secondly, the cancelling structures require considerable computational processing effort to adapt to primary source and plant changes, particularly for multi-channel systems. This paper describes methods to increase the adaptive speed to primary source changes in large enclosed spaces and outdoor environments. A method is described that increases the response to time varying periodic noise using traditional transverse FIR filters. Here a multi-passband filter, with individual variable adaptive step sizes for each passband is automatically adjusted according to the signal level in each band. This creates a similar adaptive response for all frequencies within the total pass-band, irrespective of amplitude, minimizing the signal distortion and increasing the combined adaptive speed. Unfortunately, there is a limit to the adaptive speed using the above method as classical transverse FIR filters have a finite adaptive speed given by the stability band zero bandwidth. For rapidly changing periodic noise and unpredictable non-stationary noise, a rapid to instantaneous response is required. In this case the on-line adaptive FIR filters are dispensed with and replaced by a time domain solution that gives virtually instantaneous cancellation response (infinite adaptive speed) to primary source changes, and is computationally efficient.

  2. Emergent Adaptive Noise Reduction from Communal Cooperation of Sensor Grid

    NASA Technical Reports Server (NTRS)

    Jones, Kennie H.; Jones, Michael G.; Nark, Douglas M.; Lodding, Kenneth N.

    2010-01-01

    In the last decade, the realization of small, inexpensive, and powerful devices with sensors, computers, and wireless communication has promised the development of massive sized sensor networks with dense deployments over large areas capable of high fidelity situational assessments. However, most management models have been based on centralized control and research has concentrated on methods for passing data from sensor devices to the central controller. Most implementations have been small but, as it is not scalable, this methodology is insufficient for massive deployments. Here, a specific application of a large sensor network for adaptive noise reduction demonstrates a new paradigm where communities of sensor/computer devices assess local conditions and make local decisions from which emerges a global behaviour. This approach obviates many of the problems of centralized control as it is not prone to single point of failure and is more scalable, efficient, robust, and fault tolerant

  3. A multi-band spectral subtraction-based algorithm for real-time noise cancellation applied to gunshot acoustics

    NASA Astrophysics Data System (ADS)

    Ramos, António L. L.; Holm, Sverre; Gudvangen, Sigmund; Otterlei, Ragnvald

    2013-06-01

    Acoustical sniper positioning is based on the detection and direction-of-arrival estimation of the shockwave and the muzzle blast acoustical signals. In real-life situations, the detection and direction-of-arrival estimation processes is usually performed under the influence of background noise sources, e.g., vehicles noise, and might result in non-negligible inaccuracies than can affect the system performance and reliability negatively, specially when detecting the muzzle sound under long range distance and absorbing terrains. This paper introduces a multi-band spectral subtraction based algorithm for real-time noise reduction, applied to gunshot acoustical signals. The ballistic shockwave and the muzzle blast signals exhibit distinct frequency contents that are affected differently by additive noise. In most real situations, the noise component is colored and a multi-band spectral subtraction approach for noise reduction contributes to reducing the presence of artifacts in denoised signals. The proposed algorithm is tested using a dataset generated by combining signals from real gunshots and real vehicle noise. The noise component was generated using a steel tracked military tank running on asphalt and includes, therefore, the sound from the vehicle engine, which varies slightly in frequency over time according to the engine's rpm, and the sound from the steel tracks as the vehicle moves.

  4. Interior Noise Reduction by Adaptive Feedback Vibration Control

    NASA Technical Reports Server (NTRS)

    Lim, Tae W.

    1998-01-01

    The objective of this project is to investigate the possible use of adaptive digital filtering techniques in simultaneous, multiple-mode identification of the modal parameters of a vibrating structure in real-time. It is intended that the results obtained from this project will be used for state estimation needed in adaptive structural acoustics control. The work done in this project is basically an extension of the work on real-time single mode identification, which was performed successfully using a digital signal processor (DSP) at NASA, Langley. Initially, in this investigation the single mode identification work was duplicated on a different processor, namely the Texas Instruments TMS32OC40 DSP. The system identification results for the single mode case were very good. Then an algorithm for simultaneous two mode identification was developed and tested using analytical simulation. When it successfully performed the expected tasks, it was implemented in real-time on the DSP system to identify the first two modes of vibration of a cantilever aluminum beam. The results of the simultaneous two mode case were good but some problems were identified related to frequency warping and spurious mode identification. The frequency warping problem was found to be due to the bilinear transformation used in the algorithm to convert the system transfer function from the continuous-time domain to the discrete-time domain. An alternative approach was developed to rectify the problem. The spurious mode identification problem was found to be associated with high sampling rates. Noise in the signal is suspected to be the cause of this problem but further investigation will be needed to clarify the cause. For simultaneous identification of more than two modes, it was found that theoretically an adaptive digital filter can be designed to identify the required number of modes, but the algebra became very complex which made it impossible to implement in the DSP system used in this study

  5. Differential-mode vibrational noise cancellation structure for Metglas/Pb(Zr,Ti)O₃ fiber magnetoelectric laminates.

    PubMed

    Gao, Junqi; Zhai, Junyi; Shen, Ying; Shen, Liangguo; Gray, David; Li, Jiefang; Finkel, Peter; Viehland, D

    2011-08-01

    A differential structure which has the ability to reject external vibrational noise for Metglas/Pb(Zr,Ti)O(3) (PZT) fiber-based magnetoelectric (ME) heterostructures has been studied. This type of ME structure functions better than conventional sensors as a magnetic sensor when used in an environment in which vibrational isolation is impractical. Sensors fabricated with this differential mode structure can attenuate external vibrational noise by about 10 to 20 dB at different frequencies, while simultaneously having a doubled ME voltage coefficient. Interestingly, in addition to offering a means of mitigating vibrational noise, this ME structure offers the potential to be a hybrid sensor, separating magnetic and acoustical signals.

  6. UV/visible Fourier transform spectroscopy using an inductively-coupled plasma: dual-channel noise cancellation

    NASA Astrophysics Data System (ADS)

    Travis, J. C.; Winchester, M. R.; Salit, M. L.; Wythoff, B. J.; Scheeline, A.

    1993-04-01

    Although technological advances have extended the range of Fourier transform spectroscopy (FTS) into the UV/visible spectral domain, its application to spectroscopic and spectrometric problems has been hampered-relative to such applications in the infrared domain-by noise considerations. Although the technique retains high resolution, accurate wavelength registration, and simultaneous broad band coverage, the multiplex advantage present in the IR is severely compromised in the UV/visible due to the relative insignificance of detector noise. In particular, signal-carried noise distributes widely through the spectrum, degrading the dynamic range needed for many spectroscopic and analytical applications. This study demonstrates the use of complementary optical output channels in a commercial FTS to achieve up to ten-fold noise reductions for spectra acquired from an analytical inductively-coupled plasma with conventional pneumatic sample aspiration. The study also demonstrates the advisability of increasing the sampling rate of future instruments to exceed the maximum noise frequency characteristic of droplet evaporation effects.

  7. Adaptive neuro-fuzzy methodology for noise assessment of wind turbine.

    PubMed

    Shamshirband, Shahaboddin; Petković, Dalibor; Hashim, Roslan; Motamedi, Shervin

    2014-01-01

    Wind turbine noise is one of the major obstacles for the widespread use of wind energy. Noise tone can greatly increase the annoyance factor and the negative impact on human health. Noise annoyance caused by wind turbines has become an emerging problem in recent years, due to the rapid increase in number of wind turbines, triggered by sustainable energy goals set forward at the national and international level. Up to now, not all aspects of the generation, propagation and perception of wind turbine noise are well understood. For a modern large wind turbine, aerodynamic noise from the blades is generally considered to be the dominant noise source, provided that mechanical noise is adequately eliminated. The sources of aerodynamic noise can be divided into tonal noise, inflow turbulence noise, and airfoil self-noise. Many analytical and experimental acoustical studies performed the wind turbines. Since the wind turbine noise level analyzing by numerical methods or computational fluid dynamics (CFD) could be very challenging and time consuming, soft computing techniques are preferred. To estimate noise level of wind turbine, this paper constructed a process which simulates the wind turbine noise levels in regard to wind speed and sound frequency with adaptive neuro-fuzzy inference system (ANFIS). This intelligent estimator is implemented using Matlab/Simulink and the performances are investigated. The simulation results presented in this paper show the effectiveness of the developed method.

  8. Adaptive Neuro-Fuzzy Methodology for Noise Assessment of Wind Turbine

    PubMed Central

    Shamshirband, Shahaboddin; Petković, Dalibor; Hashim, Roslan; Motamedi, Shervin

    2014-01-01

    Wind turbine noise is one of the major obstacles for the widespread use of wind energy. Noise tone can greatly increase the annoyance factor and the negative impact on human health. Noise annoyance caused by wind turbines has become an emerging problem in recent years, due to the rapid increase in number of wind turbines, triggered by sustainable energy goals set forward at the national and international level. Up to now, not all aspects of the generation, propagation and perception of wind turbine noise are well understood. For a modern large wind turbine, aerodynamic noise from the blades is generally considered to be the dominant noise source, provided that mechanical noise is adequately eliminated. The sources of aerodynamic noise can be divided into tonal noise, inflow turbulence noise, and airfoil self-noise. Many analytical and experimental acoustical studies performed the wind turbines. Since the wind turbine noise level analyzing by numerical methods or computational fluid dynamics (CFD) could be very challenging and time consuming, soft computing techniques are preferred. To estimate noise level of wind turbine, this paper constructed a process which simulates the wind turbine noise levels in regard to wind speed and sound frequency with adaptive neuro-fuzzy inference system (ANFIS). This intelligent estimator is implemented using Matlab/Simulink and the performances are investigated. The simulation results presented in this paper show the effectiveness of the developed method. PMID:25075621

  9. Adaptive neuro-fuzzy methodology for noise assessment of wind turbine.

    PubMed

    Shamshirband, Shahaboddin; Petković, Dalibor; Hashim, Roslan; Motamedi, Shervin

    2014-01-01

    Wind turbine noise is one of the major obstacles for the widespread use of wind energy. Noise tone can greatly increase the annoyance factor and the negative impact on human health. Noise annoyance caused by wind turbines has become an emerging problem in recent years, due to the rapid increase in number of wind turbines, triggered by sustainable energy goals set forward at the national and international level. Up to now, not all aspects of the generation, propagation and perception of wind turbine noise are well understood. For a modern large wind turbine, aerodynamic noise from the blades is generally considered to be the dominant noise source, provided that mechanical noise is adequately eliminated. The sources of aerodynamic noise can be divided into tonal noise, inflow turbulence noise, and airfoil self-noise. Many analytical and experimental acoustical studies performed the wind turbines. Since the wind turbine noise level analyzing by numerical methods or computational fluid dynamics (CFD) could be very challenging and time consuming, soft computing techniques are preferred. To estimate noise level of wind turbine, this paper constructed a process which simulates the wind turbine noise levels in regard to wind speed and sound frequency with adaptive neuro-fuzzy inference system (ANFIS). This intelligent estimator is implemented using Matlab/Simulink and the performances are investigated. The simulation results presented in this paper show the effectiveness of the developed method. PMID:25075621

  10. SEMICONDUCTOR INTEGRATED CIRCUITS: Noise-canceling and IP3 improved CMOS RF front-end for DRM/DAB/DVB-H applications

    NASA Astrophysics Data System (ADS)

    Keping, Wang; Zhigong, Wang; Xuemei, Lei

    2010-02-01

    A CMOS RF (radio frequency) front-end for digital radio broadcasting applications is presented that contains a wideband LNA, I/Q-mixers and VGAs, supporting other various wireless communication standards in the ultra-wide frequency band from 200 kHz to 2 GHz as well. Improvement of the NF (noise figure) and IP3 (third-order intermodulation distortion) is attained without significant degradation of other performances like voltage gain and power consumption. The NF is minimized by noise-canceling technology, and the IP3 is improved by using differential multiple gate transistors (DMGTR). The dB-in-linear VGA (variable gain amplifier) exploits a single PMOS to achieve exponential gain control. The circuit is fabricated in 0.18-μm CMOS technology. The S11 of the RF front-end is lower than -11.4 dB over the whole band of 200 kHz-2 GHz. The variable gain range is 12-42 dB at 0.25 GHz and 4-36 dB at 2 GHz. The DSB NF at maximum gain is 3.1-6.1 dB. The IIP3 at middle gain is -4.7 to 0.2 dBm. It consumes a DC power of only 36 mW at 1.8 V supply.

  11. Adaptive cyclic physiologic noise modeling and correction in functional MRI.

    PubMed

    Beall, Erik B

    2010-03-30

    Physiologic noise in BOLD-weighted MRI data is known to be a significant source of the variance, reducing the statistical power and specificity in fMRI and functional connectivity analyses. We show a dramatic improvement on current noise correction methods in both fMRI and fcMRI data that avoids overfitting. The traditional noise model is a Fourier series expansion superimposed on the periodicity of parallel measured breathing and cardiac cycles. Correction using this model results in removal of variance matching the periodicity of the physiologic cycles. Using this framework allows easy modeling of noise. However, using a large number of regressors comes at the cost of removing variance unrelated to physiologic noise, such as variance due to the signal of functional interest (overfitting the data). It is our hypothesis that there are a small variety of fits that describe all of the significantly coupled physiologic noise. If this is true, we can replace a large number of regressors used in the model with a smaller number of the fitted regressors and thereby account for the noise sources with a smaller reduction in variance of interest. We describe these extensions and demonstrate that we can preserve variance in the data unrelated to physiologic noise while removing physiologic noise equivalently, resulting in data with a higher effective SNR than with current corrections techniques. Our results demonstrate a significant improvement in the sensitivity of fMRI (up to a 17% increase in activation volume for fMRI compared with higher order traditional noise correction) and functional connectivity analyses.

  12. Shape anomaly detection under strong measurement noise: An analytical approach to adaptive thresholding

    NASA Astrophysics Data System (ADS)

    Krasichkov, Alexander S.; Grigoriev, Eugene B.; Bogachev, Mikhail I.; Nifontov, Eugene M.

    2015-10-01

    We suggest an analytical approach to the adaptive thresholding in a shape anomaly detection problem. We find an analytical expression for the distribution of the cosine similarity score between a reference shape and an observational shape hindered by strong measurement noise that depends solely on the noise level and is independent of the particular shape analyzed. The analytical treatment is also confirmed by computer simulations and shows nearly perfect agreement. Using this analytical solution, we suggest an improved shape anomaly detection approach based on adaptive thresholding. We validate the noise robustness of our approach using typical shapes of normal and pathological electrocardiogram cycles hindered by additive white noise. We show explicitly that under high noise levels our approach considerably outperforms the conventional tactic that does not take into account variations in the noise level.

  13. Adaptive filters of stationary-noise compensation which correspond to a Toeplitz correlation-matrix structure

    NASA Astrophysics Data System (ADS)

    Abramovich, Iu. I.; Arov, D. Z.; Kachur, V. G.

    1987-12-01

    The paper considers the problem of finding the vector of an adaptive filter of stationary-noise compensation which corresponds to a Toeplitz correlation-matrix structure. The existence of a Toeplitz solution is demonstrated. Lower-bound estimates are obtained for the gain in noise-compensation efficiency using a priori information about the Toeplitz matrix structure. Constructive methods for obtaining adaptive solutions corresponding to these estimates are indicated.

  14. Adaptive noise estimation and suppression for improving microseismic event detection

    NASA Astrophysics Data System (ADS)

    Mousavi, S. Mostafa; Langston, Charles A.

    2016-09-01

    Microseismic data recorded by surface arrays are often strongly contaminated by unwanted noise. This background noise makes the detection of small magnitude events difficult. A noise level estimation and noise reduction algorithm is presented for microseismic data analysis based upon minimally controlled recursive averaging and neighborhood shrinkage estimators. The method might not be compared with more sophisticated and computationally expensive denoising algorithm in terms of preserving detailed features of seismic signal. However, it is fast and data-driven and can be applied in real-time processing of continuous data for event detection purposes. Results from application of this algorithm to synthetic and real seismic data show that it holds a great promise for improving microseismic event detection.

  15. Adaptive filter based two-probe noise suppression system for transient evoked otoacoustic emission detection.

    PubMed

    Subotić, Miško; Šarić, Zoran; Jovičić, Slobodan T

    2012-03-01

    Transient otoacoustic emission (TEOAE) is a method widely used in clinical practice for assessment of hearing quality. The main problem in TEOAE detection is its much lower level than the level of environmental and biological noise. While the environmental noise level can be controlled, the biological noise can be only reduced by appropriate signal processing. This paper presents a new two-probe preprocessing TEOAE system for suppression of the biological noise by adaptive filtering. The system records biological noises in both ears and applies a specific adaptive filtering approach for suppression of biological noise in the ear canal with TEOAE. The adaptive filtering approach includes robust sign error LMS algorithm, stimuli response summation according to the derived non-linear response (DNLR) technique, subtraction of the estimated TEOAE signal and residual noise suppression. The proposed TEOAE detection system is tested by three quality measures: signal-to-noise ratio (S/N), reproducibility of TEOAE, and measurement time. The maximal TEOAE detection improvement is dependent on the coherence function between biological noise in left and right ears. The experimental results show maximal improvement of 7 dB in S/N, improvement in reproducibility near 40% and reduction in duration of TEOAE measurement of over 30%.

  16. Wavelet-Based Speech Enhancement Using Time-Adapted Noise Estimation

    NASA Astrophysics Data System (ADS)

    Lei, Sheau-Fang; Tung, Ying-Kai

    Spectral subtraction is commonly used for speech enhancement in a single channel system because of the simplicity of its implementation. However, this algorithm introduces perceptually musical noise while suppressing the background noise. We propose a wavelet-based approach in this paper for suppressing the background noise for speech enhancement in a single channel system. The wavelet packet transform, which emulates the human auditory system, is used to decompose the noisy signal into critical bands. Wavelet thresholding is then temporally adjusted with the noise power by time-adapted noise estimation. The proposed algorithm can efficiently suppress the noise while reducing speech distortion. Experimental results, including several objective measurements, show that the proposed wavelet-based algorithm outperforms spectral subtraction and other wavelet-based denoising approaches for speech enhancement for nonstationary noise environments.

  17. Adaptive anisotropic diffusion for noise reduction of phase images in Fourier domain Doppler optical coherence tomography.

    PubMed

    Xia, Shaoyan; Huang, Yong; Peng, Shizhao; Wu, Yanfeng; Tan, Xiaodi

    2016-08-01

    Phase image in Fourier domain Doppler optical coherence tomography offers additional flow information of investigated samples, which provides valuable evidence towards accurate medical diagnosis. High quality phase images are thus desirable. We propose a noise reduction method for phase images by combining a synthetic noise estimation criteria based on local noise estimator (LNE) and distance median value (DMV) with anisotropic diffusion model. By identifying noise and signal pixels accurately and diffusing them with different coefficients respectively and adaptive iteration steps, we demonstrated the effectiveness of our proposed method in both phantom and mouse artery images. Comparison with other methods such as filtering method (mean, median filtering), wavelet method, probabilistic method and partial differential equation based methods in terms of peak signal-to-noise ratio (PSNR), equivalent number of looks (ENL) and contrast-to-noise ratio (CNR) showed the advantages of our method in reserving image energy and removing noise. PMID:27570687

  18. Adaptive anisotropic diffusion for noise reduction of phase images in Fourier domain Doppler optical coherence tomography

    PubMed Central

    Xia, Shaoyan; Huang, Yong; Peng, Shizhao; Wu, Yanfeng; Tan, Xiaodi

    2016-01-01

    Phase image in Fourier domain Doppler optical coherence tomography offers additional flow information of investigated samples, which provides valuable evidence towards accurate medical diagnosis. High quality phase images are thus desirable. We propose a noise reduction method for phase images by combining a synthetic noise estimation criteria based on local noise estimator (LNE) and distance median value (DMV) with anisotropic diffusion model. By identifying noise and signal pixels accurately and diffusing them with different coefficients respectively and adaptive iteration steps, we demonstrated the effectiveness of our proposed method in both phantom and mouse artery images. Comparison with other methods such as filtering method (mean, median filtering), wavelet method, probabilistic method and partial differential equation based methods in terms of peak signal-to-noise ratio (PSNR), equivalent number of looks (ENL) and contrast-to-noise ratio (CNR) showed the advantages of our method in reserving image energy and removing noise. PMID:27570687

  19. Calibration and adaptation of ISO visual noise for I3A's Camera Phone Image Quality initiative

    NASA Astrophysics Data System (ADS)

    Baxter, Donald J.; Murray, Andrew

    2012-01-01

    The I3A Camera Phone Image Quality (CPIQ) visual noise metric described is a core image quality attribute of the wider I3A CPIQ consumer orientated, camera image quality score. This paper describes the selection of a suitable noise metric, the adaptation of the chosen ISO 15739 visual noise protocol for the challenges posed by cell phone cameras and the mapping of the adapted protocol to subjective image quality loss using a published noise study. Via a simple study, visual noise metrics are shown to discriminate between different noise frequency shapes. The optical non-uniformities prevalent in cell phone cameras and higher noise levels pose significant challenges to the ISO 15739 visual noise protocol. The non-uniformities are addressed using a frequency based high pass filter. Secondly, the data clipping at high noise levels is avoided using a Johnson and Fairchild frequency based Luminance contrast sensitivity function (CSF). The final result is a visually based noise metric calibrated in Quality Loss Just Noticeable Differences (JND) using Aptina Imaging's subjectively calibrated image set.

  20. Noise Filtering Strategies in Adaptive Biochemical Signaling Networks. Application to E. Coli Chemotaxis

    NASA Astrophysics Data System (ADS)

    Sartori, Pablo; Tu, Yuhai

    2011-04-01

    Two distinct mechanisms for filtering noise in an input signal are identified in a class of adaptive sensory networks. We find that the high-frequency noise is filtered by the output degradation process through time-averaging; while the low-frequency noise is damped by adaptation through negative feedback. Both filtering processes themselves introduce intrinsic noises, which are found to be unfiltered and can thus amount to a significant internal noise floor even without signaling. These results are applied to E. coli chemotaxis. We show unambiguously that the molecular mechanism for the Berg-Purcell time-averaging scheme is the dephosphorylation of the response regulator CheY-P, not the receptor adaptation process as previously suggested. The high-frequency noise due to the stochastic ligand binding-unbinding events and the random ligand molecule diffusion is averaged by the CheY-P dephosphorylation process to a negligible level in E. coli. We identify a previously unstudied noise source caused by the random motion of the cell in a ligand gradient. We show that this random walk induced signal noise has a divergent low-frequency component, which is only rendered finite by the receptor adaptation process. For gradients within the E. coli sensing range, this dominant external noise can be comparable to the significant intrinsic noise in the system. The dependence of the response and its fluctuations on the key time scales of the system are studied systematically. We show that the chemotaxis pathway may have evolved to optimize gradient sensing, strong response, and noise control in different time scales.

  1. Adaptive nonlocal means filtering based on local noise level for CT denoising

    SciTech Connect

    Li, Zhoubo; Trzasko, Joshua D.; Lake, David S.; Blezek, Daniel J.; Manduca, Armando; Yu, Lifeng; Fletcher, Joel G.; McCollough, Cynthia H.

    2014-01-15

    Purpose: To develop and evaluate an image-domain noise reduction method based on a modified nonlocal means (NLM) algorithm that is adaptive to local noise level of CT images and to implement this method in a time frame consistent with clinical workflow. Methods: A computationally efficient technique for local noise estimation directly from CT images was developed. A forward projection, based on a 2D fan-beam approximation, was used to generate the projection data, with a noise model incorporating the effects of the bowtie filter and automatic exposure control. The noise propagation from projection data to images was analytically derived. The analytical noise map was validated using repeated scans of a phantom. A 3D NLM denoising algorithm was modified to adapt its denoising strength locally based on this noise map. The performance of this adaptive NLM filter was evaluated in phantom studies in terms of in-plane and cross-plane high-contrast spatial resolution, noise power spectrum (NPS), subjective low-contrast spatial resolution using the American College of Radiology (ACR) accreditation phantom, and objective low-contrast spatial resolution using a channelized Hotelling model observer (CHO). Graphical processing units (GPU) implementation of this noise map calculation and the adaptive NLM filtering were developed to meet demands of clinical workflow. Adaptive NLM was piloted on lower dose scans in clinical practice. Results: The local noise level estimation matches the noise distribution determined from multiple repetitive scans of a phantom, demonstrated by small variations in the ratio map between the analytical noise map and the one calculated from repeated scans. The phantom studies demonstrated that the adaptive NLM filter can reduce noise substantially without degrading the high-contrast spatial resolution, as illustrated by modulation transfer function and slice sensitivity profile results. The NPS results show that adaptive NLM denoising preserves the

  2. Non-adaptive robust filters for speckle noise reduction

    NASA Astrophysics Data System (ADS)

    Frery, Alejandro C.; Santanna, Sidnei J. S.

    1993-06-01

    After briefly reviewing some classical filters for speckle removal, five filters with characteristics of robustness, suitable for speckle noise reduction, are derived and implemented. These filters are the ones based on the trimmed maximum likelihood and moments estimators, the ones based on the median, on the inter-quartile range, and on the median absolute deviation. Assuming that observations within a synthetic aperture radar image are outcomes of independent Rayleigh random variables, these filters exhibit a good performance from both the signal-to-noise reduction and from the edge preserving criteria. The problem of filtering in an image is posed as an estimation problem.

  3. Adaptive alpha-trimmed mean filters under deviations from assumed noise model.

    PubMed

    Oten, Remzi; de Figueiredo, Rui J P

    2004-05-01

    Alpha-trimmed mean filters are widely used for the restoration of signals and images corrupted by additive non-Gaussian noise. They are especially preferred if the underlying noise deviates from Gaussian with the impulsive noise components. The key design issue of these filters is to select its only parameter, alpha, optimally for a given noise type. In image restoration, adaptive filters utilize the flexibility of selecting alpha according to some local noise statistics. In the present paper, we first review the existing adaptive alpha-trimmed mean filter schemes. We then analyze the performance of these filters when the underlying noise distribution deviates from the Gaussian and does not satisfy the assumptions such as symmetry. Specifically, the clipping effect and the mixed noise cases are analyzed. We also present a new adaptive alpha-trimmed filter implementation that detects the nonsymmetry points locally and applies alpha-trimmed mean filter that trims out the outlier pixels such as edges or impulsive noise according to this local decision. Comparisons of the speed and filtering performances under deviations from symmetry and Gaussian assumptions show that the proposed filter is a very good alternative to the existing schemes. PMID:15376595

  4. An adaptive clutter and interference suppression with a minimum residue noise power

    NASA Astrophysics Data System (ADS)

    Kwag, Young Kil

    The author presents an adaptive technique for the suppression of clutter and interference in environments where no a priori knowledge about the target or the clutter and interference statistics is available. The adaptive processor generates the average weight vector, in the sense of minimum-residue-noise power, on the basis of the injected noise-level vector in the weight control algorithm. The set of weight vectors generated in a particular range-azimuth space can be stored and switched to the same sector for the unwanted-noise rejection. The adaptation rate is significantly increased when the residue noise is removed from the combiner output. The system improvement factor in suppressing the clutter and interference is not sensitive to the strength of the input CSR (clutter suppression rate) and is largely dependent on the residue clutter and interference. Simulation results show the effectiveness of the proposed method in improving the clutter and interference rejection capability.

  5. Adaptive non-local means filtering based on local noise level for CT denoising

    NASA Astrophysics Data System (ADS)

    Li, Zhoubo; Yu, Lifeng; Trzasko, Joshua D.; Fletcher, Joel G.; McCollough, Cynthia H.; Manduca, Armando

    2012-03-01

    Radiation dose from CT scans is an increasing health concern in the practice of radiology. Higher dose scans can produce clearer images with high diagnostic quality, but may increase the potential risk of radiation-induced cancer or other side effects. Lowering radiation dose alone generally produces a noisier image and may degrade diagnostic performance. Recently, CT dose reduction based on non-local means (NLM) filtering for noise reduction has yielded promising results. However, traditional NLM denoising operates under the assumption that image noise is spatially uniform noise, while in CT images the noise level varies significantly within and across slices. Therefore, applying NLM filtering to CT data using a global filtering strength cannot achieve optimal denoising performance. In this work, we have developed a technique for efficiently estimating the local noise level for CT images, and have modified the NLM algorithm to adapt to local variations in noise level. The local noise level estimation technique matches the true noise distribution determined from multiple repetitive scans of a phantom object very well. The modified NLM algorithm provides more effective denoising of CT data throughout a volume, and may allow significant lowering of radiation dose. Both the noise map calculation and the adaptive NLM filtering can be performed in times that allow integration with the clinical workflow.

  6. Adaptive control and noise suppression by a variable-gain gradient algorithm

    NASA Technical Reports Server (NTRS)

    Merhav, S. J.; Mehta, R. S.

    1987-01-01

    An adaptive control system based on normalized LMS filters is investigated. The finite impulse response of the nonparametric controller is adaptively estimated using a given reference model. Specifically, the following issues are addressed: The stability of the closed loop system is analyzed and heuristically established. Next, the adaptation process is studied for piecewise constant plant parameters. It is shown that by introducing a variable-gain in the gradient algorithm, a substantial reduction in the LMS adaptation rate can be achieved. Finally, process noise at the plant output generally causes a biased estimate of the controller. By introducing a noise suppression scheme, this bias can be substantially reduced and the response of the adapted system becomes very close to that of the reference model. Extensive computer simulations validate these and demonstrate assertions that the system can rapidly adapt to random jumps in plant parameters.

  7. End-point variability is not noise in saccade adaptation.

    PubMed

    Herman, James P; Cloud, C Phillip; Wallman, Josh

    2013-01-01

    When each of many saccades is made to overshoot its target, amplitude gradually decreases in a form of motor learning called saccade adaptation. Overshoot is induced experimentally by a secondary, backwards intrasaccadic target step (ISS) triggered by the primary saccade. Surprisingly, however, no study has compared the effectiveness of different sizes of ISS in driving adaptation by systematically varying ISS amplitude across different sessions. Additionally, very few studies have examined the feasibility of adaptation with relatively small ISSs. In order to best understand saccade adaptation at a fundamental level, we addressed these two points in an experiment using a range of small, fixed ISS values (from 0° to 1° after a 10° primary target step). We found that significant adaptation occurred across subjects with an ISS as small as 0.25°. Interestingly, though only adaptation in response to 0.25° ISSs appeared to be complete (the magnitude of change in saccade amplitude was comparable to size of the ISS), further analysis revealed that a comparable proportion of the ISS was compensated for across conditions. Finally, we found that ISS size alone was sufficient to explain the magnitude of adaptation we observed; additional factors did not significantly improve explanatory power. Overall, our findings suggest that current assumptions regarding the computation of saccadic error may need to be revisited.

  8. Micropower non-contact EEG electrode with active common-mode noise suppression and input capacitance cancellation.

    PubMed

    Chi, Yu M; Cauwenberghs, Gert

    2009-01-01

    A non-contact EEG electrode with input capacitance neutralization and common-mode noise suppression circuits is presented. The coin sized sensor capacitively couples to the scalp without direct contact to the skin. To minimize the effect of signal attenuation and channel gain mismatch, the input capacitance of each sensor is actively neutralized using positive feedback and bootstrapping. Common-mode suppression is achieved through a single conductive sheet to establish a common mode reference. Each sensor electrode provides a differential gain of 60 dB. Signals are transmitted in a digital serial daisy-chain directly from a local 16-bit ADC, minimizing the number of wires required to establish a high density EEG sensor network. The micropower electrode consumes only 600 microW from a single 3.3 V supply.

  9. Construction and solution of an adaptive image-restoration model for removing blur and mixed noise

    NASA Astrophysics Data System (ADS)

    Wang, Youquan; Cui, Lihong; Cen, Yigang; Sun, Jianjun

    2016-03-01

    We establish a practical regularized least-squares model with adaptive regularization for dealing with blur and mixed noise in images. This model has some advantages, such as good adaptability for edge restoration and noise suppression due to the application of a priori spatial information obtained from a polluted image. We further focus on finding an important feature of image restoration using an adaptive restoration model with different regularization parameters in polluted images. A more important observation is that the gradient of an image varies regularly from one regularization parameter to another under certain conditions. Then, a modified graduated nonconvexity approach combined with a median filter version of a spatial information indicator is proposed to seek the solution of our adaptive image-restoration model by applying variable splitting and weighted penalty techniques. Numerical experiments show that the method is robust and effective for dealing with various blur and mixed noise levels in images.

  10. An Efficient Adaptive Weighted Switching Median Filter for Removing High Density Impulse Noise

    NASA Astrophysics Data System (ADS)

    Nair, Madhu S.; Ameera Mol, P. M.

    2014-09-01

    Restoration of images corrupted by impulse noise is a very active research area in image processing. In this paper, an Efficient Adaptive Weighted Switching Median filter for restoration of images that are corrupted by high density impulse noise is proposed. The filtering is performed as a two phase process—a detection phase followed by a filtering phase. In the proposed method, noise detection is done by HEIND algorithm proposed by Duan et al. The filtering algorithm is then applied to the pixels which are detected as noisy by the detection algorithm. All uncorrupted pixels in the image are left unchanged. The filtering window size is chosen adaptively depending on the local noise distribution around each corrupted pixels. Noisy pixels are replaced by a weighted median value of uncorrupted pixels in the filtering window. The weight value assigned to each uncorrupted pixels depends on its closeness to the central pixel.

  11. Acoustooptic processor for adaptive radar noise environment characterization.

    PubMed

    Goutzoulis, A P; Casasent, D; Kumar, B V

    1984-12-01

    A new 2-D acoustooptic processor that estimates the angular as well as spectral distributions of jammers in the far field of an adaptive phased array radar is described. The operating modes of the system are discussed together with the estimation accuracy achieved. Experimental results are presented to illustrate the operation of the processor, and different acoustooptic cell operating modes are discussed.

  12. Adaptive Autoregressive Model for Reduction of Noise in SPECT.

    PubMed

    Takalo, Reijo; Hytti, Heli; Ihalainen, Heimo; Sohlberg, Antti

    2015-01-01

    This paper presents improved autoregressive modelling (AR) to reduce noise in SPECT images. An AR filter was applied to prefilter projection images and postfilter ordered subset expectation maximisation (OSEM) reconstruction images (AR-OSEM-AR method). The performance of this method was compared with filtered back projection (FBP) preceded by Butterworth filtering (BW-FBP method) and the OSEM reconstruction method followed by Butterworth filtering (OSEM-BW method). A mathematical cylinder phantom was used for the study. It consisted of hot and cold objects. The tests were performed using three simulated SPECT datasets. Image quality was assessed by means of the percentage contrast resolution (CR%) and the full width at half maximum (FWHM) of the line spread functions of the cylinders. The BW-FBP method showed the highest CR% values and the AR-OSEM-AR method gave the lowest CR% values for cold stacks. In the analysis of hot stacks, the BW-FBP method had higher CR% values than the OSEM-BW method. The BW-FBP method exhibited the lowest FWHM values for cold stacks and the AR-OSEM-AR method for hot stacks. In conclusion, the AR-OSEM-AR method is a feasible way to remove noise from SPECT images. It has good spatial resolution for hot objects.

  13. Noise in adaptive interferometric fiber sensor based on population dynamic grating in erbium-doped fiber.

    PubMed

    Stepanov, Serguei; Sánchez, Marcos Plata; Hernández, Eliseo Hernández

    2016-09-10

    Experimental investigations of the main noise sources that limit the sensitivity of the adaptive interferometric all-fiber sensors operating in the communication wavelength region are reported. Adaptive properties (i.e., the autostabilization of an optimal operation point of the interferometer) are enabled by the dynamic population grating recorded in a segment of the erbium-doped fiber (EDF) at milliwatt-scale cw power in the 1480-1560 nm spectral range. The utilized symmetric Sagnac configuration with low light internal reflections ensures reduced sensitivity of the sensor to phase noise of the laser, while intensity noise is reduced to an insignificant level by the balanced detection scheme. It is shown that the fluorescence from the erbium ions, excited by the counterpropagating waves recording the grating, increases the noise level from the fundamental shot noise approximately by a factor of 2-3 only. It is also shown that conventional communication distributed feedback (DFB) semiconductor lasers with megahertz linewidth are not suitable for high-sensitivity applications of such sensors. Because of inevitable backreflections from the output terminal devices (photodiodes, insulators, circulator), the above-mentioned fundamental noise level is increased by 2 orders of magnitude due to high phase noise of the DFB laser. PMID:27661369

  14. Noise in adaptive interferometric fiber sensor based on population dynamic grating in erbium-doped fiber.

    PubMed

    Stepanov, Serguei; Sánchez, Marcos Plata; Hernández, Eliseo Hernández

    2016-09-10

    Experimental investigations of the main noise sources that limit the sensitivity of the adaptive interferometric all-fiber sensors operating in the communication wavelength region are reported. Adaptive properties (i.e., the autostabilization of an optimal operation point of the interferometer) are enabled by the dynamic population grating recorded in a segment of the erbium-doped fiber (EDF) at milliwatt-scale cw power in the 1480-1560 nm spectral range. The utilized symmetric Sagnac configuration with low light internal reflections ensures reduced sensitivity of the sensor to phase noise of the laser, while intensity noise is reduced to an insignificant level by the balanced detection scheme. It is shown that the fluorescence from the erbium ions, excited by the counterpropagating waves recording the grating, increases the noise level from the fundamental shot noise approximately by a factor of 2-3 only. It is also shown that conventional communication distributed feedback (DFB) semiconductor lasers with megahertz linewidth are not suitable for high-sensitivity applications of such sensors. Because of inevitable backreflections from the output terminal devices (photodiodes, insulators, circulator), the above-mentioned fundamental noise level is increased by 2 orders of magnitude due to high phase noise of the DFB laser.

  15. Adaptive box filters for removal of random noise from digital images

    USGS Publications Warehouse

    Eliason, E.M.; McEwen, A.S.

    1990-01-01

    We have developed adaptive box-filtering algorithms to (1) remove random bit errors (pixel values with no relation to the image scene) and (2) smooth noisy data (pixels related to the image scene but with an additive or multiplicative component of noise). For both procedures, we use the standard deviation (??) of those pixels within a local box surrounding each pixel, hence they are adaptive filters. This technique effectively reduces speckle in radar images without eliminating fine details. -from Authors

  16. Burst noise reduction of image by decimation and adaptive weighted median filter

    NASA Astrophysics Data System (ADS)

    Nakayama, Fumitaka; Meguro, Mitsuhiko; Hamada, Nozomu

    2000-12-01

    The removal of noise in image is one of the important issues, and useful as a preprocessing for edge detection, motion estimation and so on. Recently, many studies on the nonlinear digital filter for impulsive noise reduction have been reported. The median filter, the representative of the nonlinear filters, is very effective for removing impulsive noise and preserving sharp edge. In some cases, burst (i.e., successive) impulsive noise is added to image, and this type of noise is difficult to remove by using the median filter. In this paper, we propose an Adaptive Weighted Median (AWM) filter with Decimation (AWM-D filter) for burst noise reduction. This method can also be applied to recover large destructive regions, such as blotch and scratch. The proposed filter is an extension of the Decimated Median (DM) filter, which is useful for reducing successive impulsive noise. The DM filter can split long impulsive noise sequences into short ones, and remove burst noise in spite of the short filter window. Nevertheless, the DM filter also has two disadvantages. One is that the signals without added noise is unnecessary filtered. The other is that the position information in the window is not considered in the weight determinative process, as common in the median type filter. To improve detail-preserving property of the DM filter, we use the noise detection procedure and the AWM-D filter, which can be tuned by Least Mean Absolute (LMA) algorithm. The AWM-D filter preserves details more precisely than the median-type filter, because the AWM-D filter has the weights that can control the filter output. Through some simulations, the higher performance of the proposed filter is shown compared with the simple median, the WM filter, and the DM filter.

  17. Adaptive multidirectional frequency domain filter for noise removal in wrapped phase patterns.

    PubMed

    Liu, Guixiong; Chen, Dongxue; Peng, Yanhua; Zeng, Qilin

    2016-08-01

    In order to avoid the detrimental effects of excessive noise in the phase fringe patterns of a laser digital interferometer over the accuracy of phase unwrapping and the successful detection of mechanical fatigue defects, an effective method of adaptive multidirectional frequency domain filtering is introduced based on the characteristics of the energy spectrum of localized wrapped phase patterns. Not only can this method automatically set the cutoff frequency, but it can also effectively filter out noise while preserving the image edge information. Compared with the sine and cosine transform filtering and the multidirectional frequency domain filtering, the experimental results demonstrate that the image filtered by our method has the fewest number of residues and is the closest to the noise-free image, compared to the two aforementioned methods, demonstrating the effectiveness of this adaptive multidirectional frequency domain filter. PMID:27505376

  18. Chinese-adapted youth attitude to noise scale: evaluation of validity and reliability.

    PubMed

    Zhu, Xiaofang; Bihi, Ali; Hu, Xiaolan; Lv, Yaqi; Abbas, Ali; Zhu, Xian; Mo, Lingyan; Peng, Xiaoxia

    2014-01-01

    Noise exposure is central to hearing impairment, especially for adolescents. Chinese youth frequently and consciously expose themselves to loud noise, often for many hours. Hence, a Chinese-adapted evaluative scale to measure youth's attitude toward noise could rigorously evaluate data validity and reliability. After authenticating the youth attitude to noise scale (YANS) originally developed by Olsen and Erlandsson, we purposively sampled and surveyed 642 freshmen at Capital Medical University in Beijing, China. To establish validity, we conducted confirmatory factor analysis according to Olsen's classification. To establish reliability, we calculated Cronbach's alpha coefficient and split-half coefficient. We used Bland-Altman analysis to calculate the agreement limits between test and retest. Among 642 students, 550 (85.67%) participated in statistical analysis (399 females [72.55%] vs. 151 males [27.45%]). Confirmatory factorial analysis sorted 19 items into four main subcategories (F1-F4) in terms of factor load, yielding a correlation coefficient between factors <0.40. The Cronbach's alpha coefficient (0.70) was within the desirable range, confirming the reliability of Chinese-adapted YANS. The split-half coefficient was 0.53. Furthermore, the paired t-test reported a mean difference of 0.002 (P = 0.9601). Notably, the mean overall YANS score (3.46) was similar to YANS testing in Belgium (3.10), but higher than Sweden (2.10) and Brazil (2.80). The Chinese version of the YANS questionnaire is valid, reliable, and adaptable to Chinese adolescents. Analysis of the adapted YANS showed that a significant number of Chinese youth display a poor attitude and behavior toward noise. Therefore, Chinese YANS can play a pivotal role in programs that focus on increasing youth awareness of noise and hearing health.

  19. An adaptive way for improving noise reduction using local geometric projection

    NASA Astrophysics Data System (ADS)

    Leontitsis, Alexandros; Bountis, Tassos; Pagge, Jenny

    2004-03-01

    We propose an adaptive way to improve noise reduction by local geometric projection. From the neighborhood of each candidate point in phase space, we identify the best subspace that the point will be orthogonally projected to. The signal subspace is formed by the most significant eigendirections of the neighborhood, while the less significant ones define the noise subspace. We provide a simple criterion to separate the most significant eigendirections from the less significant ones. This criterion is based on the maximum logarithmic difference between the neighborhood eigendirection lengths, and the assumption that there is at least one eigendirection that corresponds to the noise subspace. In this way, we take into account the special characteristics of each neighborhood and introduce a more successful noise reduction technique. Results are presented for a chaotic time series of the Hénon map and Ikeda map, as well as on the Nasdaq Composite index.

  20. Adaptive correction procedure for TVL1 image deblurring under impulse noise

    NASA Astrophysics Data System (ADS)

    Bai, Minru; Zhang, Xiongjun; Shao, Qianqian

    2016-08-01

    For the problem of image restoration of observed images corrupted by blur and impulse noise, the widely used TVL1 model may deviate from both the data-acquisition model and the prior model, especially for high noise levels. In order to seek a solution of high recovery quality beyond the reach of the TVL1 model, we propose an adaptive correction procedure for TVL1 image deblurring under impulse noise. Then, a proximal alternating direction method of multipliers (ADMM) is presented to solve the corrected TVL1 model and its convergence is also established under very mild conditions. It is verified by numerical experiments that our proposed approach outperforms the TVL1 model in terms of signal-to-noise ratio (SNR) values and visual quality, especially for high noise levels: it can handle salt-and-pepper noise as high as 90% and random-valued noise as high as 70%. In addition, a comparison with a state-of-the-art method, the two-phase method, demonstrates the superiority of the proposed approach.

  1. A method for image quality evaluation considering adaptation to luminance of surround and noise in stimuli

    NASA Astrophysics Data System (ADS)

    Kim, Youn Jin

    2010-09-01

    This study intends to quantify the effects of the surround luminance and noise of a given stimulus on the shape of spatial luminance contrast sensitivity function (CSF) and to propose an adaptive image quality evaluation method. The proposed image evaluation method extends a model called square-root integral (SQRI). The non-linear behaviour of the human visual system was taken into account by using CSF. This model can be defined as the square root integration of multiplication between display modulation transfer function and CSF. The CSF term in the original SQRI was replaced by the surround adaptive CSF quantified in this study and it is divided by the Fourier transform of a given stimulus for compensating for the noise adaptation.

  2. Locomotor control of limb force switches from minimal intervention principle in early adaptation to noise reduction in late adaptation.

    PubMed

    Selgrade, Brian P; Chang, Young-Hui

    2015-03-01

    During movement, errors are typically corrected only if they hinder performance. Preferential correction of task-relevant deviations is described by the minimal intervention principle but has not been demonstrated in the joints during locomotor adaptation. We studied hopping as a tractable model of locomotor adaptation of the joints within the context of a limb-force-specific task space. Subjects hopped while adapting to shifted visual feedback that induced them to increase peak ground reaction force (GRF). We hypothesized subjects would preferentially reduce task-relevant joint torque deviations over task-irrelevant deviations to increase peak GRF. We employed a modified uncontrolled manifold analysis to quantify task-relevant and task-irrelevant joint torque deviations for each individual hop cycle. As would be expected by the explicit goal of the task, peak GRF errors decreased in early adaptation before reaching steady state during late adaptation. Interestingly, during the early adaptation performance improvement phase, subjects reduced GRF errors by decreasing only the task-relevant joint torque deviations. In contrast, during the late adaption performance maintenance phase, all torque deviations decreased in unison regardless of task relevance. In deadaptation, when the shift in visual feedback was removed, all torque deviations decreased in unison, possibly because performance improvement was too rapid to detect changes in only the task-relevant dimension. We conclude that limb force adaptation in hopping switches from a minimal intervention strategy during performance improvement to a noise reduction strategy during performance maintenance, which may represent a general control strategy for locomotor adaptation of limb force in other bouncing gaits, such as running.

  3. Diagnostic analysis of vibration signals using adaptive digital filtering techniques

    NASA Technical Reports Server (NTRS)

    Jewell, R. E.; Jones, J. H.; Paul, J. E.

    1983-01-01

    Signal enhancement techniques are described using recently developed digital adaptive filtering equipment. Adaptive filtering concepts are not new; however, as a result of recent advances in microprocessor-based electronics, hardware has been developed that has stable characteristics and of a size exceeding 1000th order. Selected data processing examples are presented illustrating spectral line enhancement, adaptive noise cancellation, and transfer function estimation in the presence of corrupting noise.

  4. An adaptive segment method for smoothing lidar signal based on noise estimation

    NASA Astrophysics Data System (ADS)

    Wang, Yuzhao; Luo, Pingping

    2014-10-01

    An adaptive segmentation smoothing method (ASSM) is introduced in the paper to smooth the signal and suppress the noise. In the ASSM, the noise is defined as the 3σ of the background signal. An integer number N is defined for finding the changing positions in the signal curve. If the difference of adjacent two points is greater than 3Nσ, the position is recorded as an end point of the smoothing segment. All the end points detected as above are recorded and the curves between them will be smoothed separately. In the traditional method, the end points of the smoothing windows in the signals are fixed. The ASSM creates changing end points in different signals and the smoothing windows could be set adaptively. The windows are always set as the half of the segmentations and then the average smoothing method will be applied in the segmentations. The Iterative process is required for reducing the end-point aberration effect in the average smoothing method and two or three times are enough. In ASSM, the signals are smoothed in the spacial area nor frequent area, that means the frequent disturbance will be avoided. A lidar echo was simulated in the experimental work. The echo was supposed to be created by a space-born lidar (e.g. CALIOP). And white Gaussian noise was added to the echo to act as the random noise resulted from environment and the detector. The novel method, ASSM, was applied to the noisy echo to filter the noise. In the test, N was set to 3 and the Iteration time is two. The results show that, the signal could be smoothed adaptively by the ASSM, but the N and the Iteration time might be optimized when the ASSM is applied in a different lidar.

  5. Unstructured adaptive mesh computations of rotorcraft high-speed impulsive noise

    NASA Technical Reports Server (NTRS)

    Strawn, Roger; Garceau, Michael; Biswas, Rupak

    1993-01-01

    A new method is developed for modeling helicopter high-speed impulsive (HSI) noise. The aerodynamics and acoustics near the rotor blade tip are computed by solving the Euler equations on an unstructured grid. A stationary Kirchhoff surface integral is then used to propagate these acoustic signals to the far field. The near-field Euler solver uses a solution-adaptive grid scheme to improve the resolution of the acoustic signal. Grid points are locally added and/or deleted from the mesh at each adaptive step. An important part of this procedure is the choice of an appropriate error indicator. The error indicator is computed from the flow field solution and determines the regions for mesh coarsening and refinement. Computed results for HSI noise compare favorably with experimental data for three different hovering rotor cases.

  6. [Adaptive de-noising of ECG signal based on stationary wavelet transform].

    PubMed

    Dong, Hong-sheng; Zhang, Ai-hua; Hao, Xiao-hong

    2009-03-01

    According to the limitations of wavelet threshold in de-noising method, we approached a combining algorithm of the stationary wavelet transform with adaptive filter. The stationary wavelet transformation can suppress Gibbs phenomena in traditional DWT effectively, and adaptive filter is introduced at the high scale wavelet coefficient of the stationary wavelet transformation. It would remove baseline wander and keep the shape of low frequency and low amplitude P wave, T wave and ST segment wave of ECG signal well. That is important for analyzing ECG signal of other feature information.

  7. Audiovisual cues benefit recognition of accented speech in noise but not perceptual adaptation.

    PubMed

    Banks, Briony; Gowen, Emma; Munro, Kevin J; Adank, Patti

    2015-01-01

    Perceptual adaptation allows humans to recognize different varieties of accented speech. We investigated whether perceptual adaptation to accented speech is facilitated if listeners can see a speaker's facial and mouth movements. In Study 1, participants listened to sentences in a novel accent and underwent a period of training with audiovisual or audio-only speech cues, presented in quiet or in background noise. A control group also underwent training with visual-only (speech-reading) cues. We observed no significant difference in perceptual adaptation between any of the groups. To address a number of remaining questions, we carried out a second study using a different accent, speaker and experimental design, in which participants listened to sentences in a non-native (Japanese) accent with audiovisual or audio-only cues, without separate training. Participants' eye gaze was recorded to verify that they looked at the speaker's face during audiovisual trials. Recognition accuracy was significantly better for audiovisual than for audio-only stimuli; however, no statistical difference in perceptual adaptation was observed between the two modalities. Furthermore, Bayesian analysis suggested that the data supported the null hypothesis. Our results suggest that although the availability of visual speech cues may be immediately beneficial for recognition of unfamiliar accented speech in noise, it does not improve perceptual adaptation.

  8. Audiovisual cues benefit recognition of accented speech in noise but not perceptual adaptation.

    PubMed

    Banks, Briony; Gowen, Emma; Munro, Kevin J; Adank, Patti

    2015-01-01

    Perceptual adaptation allows humans to recognize different varieties of accented speech. We investigated whether perceptual adaptation to accented speech is facilitated if listeners can see a speaker's facial and mouth movements. In Study 1, participants listened to sentences in a novel accent and underwent a period of training with audiovisual or audio-only speech cues, presented in quiet or in background noise. A control group also underwent training with visual-only (speech-reading) cues. We observed no significant difference in perceptual adaptation between any of the groups. To address a number of remaining questions, we carried out a second study using a different accent, speaker and experimental design, in which participants listened to sentences in a non-native (Japanese) accent with audiovisual or audio-only cues, without separate training. Participants' eye gaze was recorded to verify that they looked at the speaker's face during audiovisual trials. Recognition accuracy was significantly better for audiovisual than for audio-only stimuli; however, no statistical difference in perceptual adaptation was observed between the two modalities. Furthermore, Bayesian analysis suggested that the data supported the null hypothesis. Our results suggest that although the availability of visual speech cues may be immediately beneficial for recognition of unfamiliar accented speech in noise, it does not improve perceptual adaptation. PMID:26283946

  9. Audiovisual cues benefit recognition of accented speech in noise but not perceptual adaptation

    PubMed Central

    Banks, Briony; Gowen, Emma; Munro, Kevin J.; Adank, Patti

    2015-01-01

    Perceptual adaptation allows humans to recognize different varieties of accented speech. We investigated whether perceptual adaptation to accented speech is facilitated if listeners can see a speaker’s facial and mouth movements. In Study 1, participants listened to sentences in a novel accent and underwent a period of training with audiovisual or audio-only speech cues, presented in quiet or in background noise. A control group also underwent training with visual-only (speech-reading) cues. We observed no significant difference in perceptual adaptation between any of the groups. To address a number of remaining questions, we carried out a second study using a different accent, speaker and experimental design, in which participants listened to sentences in a non-native (Japanese) accent with audiovisual or audio-only cues, without separate training. Participants’ eye gaze was recorded to verify that they looked at the speaker’s face during audiovisual trials. Recognition accuracy was significantly better for audiovisual than for audio-only stimuli; however, no statistical difference in perceptual adaptation was observed between the two modalities. Furthermore, Bayesian analysis suggested that the data supported the null hypothesis. Our results suggest that although the availability of visual speech cues may be immediately beneficial for recognition of unfamiliar accented speech in noise, it does not improve perceptual adaptation. PMID:26283946

  10. A NOISE ADAPTIVE FUZZY EQUALIZATION METHOD FOR PROCESSING SOLAR EXTREME ULTRAVIOLET IMAGES

    SciTech Connect

    Druckmueller, M.

    2013-08-15

    A new image enhancement tool ideally suited for the visualization of fine structures in extreme ultraviolet images of the corona is presented in this paper. The Noise Adaptive Fuzzy Equalization method is particularly suited for the exceptionally high dynamic range images from the Atmospheric Imaging Assembly instrument on the Solar Dynamics Observatory. This method produces artifact-free images and gives significantly better results than methods based on convolution or Fourier transform which are often used for that purpose.

  11. Contrast gain, signal-to-noise ratio, and linearity in light-adapted blowfly photoreceptors

    PubMed Central

    1994-01-01

    Response properties of short-type (R1-6) photoreceptors of the blowfly (Calliphora vicina) were investigated with intracellular recordings using repeated sequences of pseudorandomly modulated light contrast stimuli at adapting backgrounds covering 5 log intensity units. The resulting voltage responses were used to determine the effects of adaptational regulation on signal-to-noise ratios (SNR), signal induced noise, contrast gain, linearity and the dead time in phototransduction. In light adaptation the SNR of the photoreceptors improved more than 100-fold due to (a) increased photoreceptor voltage responses to a contrast stimulus and (b) reduction of voltage noise at high intensity backgrounds. In the frequency domain the SNR was attenuated in low frequencies with an increase in the middle and high frequency ranges. A pseudorandom contrast stimulus by itself did not produce any additional noise. The contrast gain of the photoreceptor frequency responses increased with mean illumination and the gain was best fitted with a model consisting of two second order and one double pole of first order. The coherence function (a normalized measure of linearity and SNR) of the frequency responses demonstrated that the photoreceptors responded linearly (from 1 to 150 Hz) to the contrast stimuli even under fairly dim conditions. The theoretically derived and the recorded phase functions were used to calculate phototransduction dead time, which decreased in light adaptation from approximately 5-2.5 ms. This analysis suggests that the ability of fly photoreceptors to maintain linear performance under dynamic stimulation conditions results from the high early gain followed by delayed compressive feed-back mechanisms. PMID:7807062

  12. Measurement of hearing aid internal noise.

    PubMed

    Lewis, James D; Goodman, Shawn S; Bentler, Ruth A

    2010-04-01

    Hearing aid equivalent input noise (EIN) measures assume the primary source of internal noise to be located prior to amplification and to be constant regardless of input level. EIN will underestimate internal noise in the case that noise is generated following amplification. The present study investigated the internal noise levels of six hearing aids (HAs). Concurrent with HA processing of a speech-like stimulus with both adaptive features (acoustic feedback cancellation, digital noise reduction, microphone directionality) enabled and disabled, internal noise was quantified for various stimulus levels as the variance across repeated trials. Changes in noise level as a function of stimulus level demonstrated that (1) generation of internal noise is not isolated to the microphone, (2) noise may be dependent on input level, and (3) certain adaptive features may contribute to internal noise. Quantifying internal noise as the variance of the output measures allows for noise to be measured under real-world processing conditions, accounts for all sources of noise, and is predictive of internal noise audibility. PMID:20370034

  13. Measurement of hearing aid internal noise1

    PubMed Central

    Lewis, James D.; Goodman, Shawn S.; Bentler, Ruth A.

    2010-01-01

    Hearing aid equivalent input noise (EIN) measures assume the primary source of internal noise to be located prior to amplification and to be constant regardless of input level. EIN will underestimate internal noise in the case that noise is generated following amplification. The present study investigated the internal noise levels of six hearing aids (HAs). Concurrent with HA processing of a speech-like stimulus with both adaptive features (acoustic feedback cancellation, digital noise reduction, microphone directionality) enabled and disabled, internal noise was quantified for various stimulus levels as the variance across repeated trials. Changes in noise level as a function of stimulus level demonstrated that (1) generation of internal noise is not isolated to the microphone, (2) noise may be dependent on input level, and (3) certain adaptive features may contribute to internal noise. Quantifying internal noise as the variance of the output measures allows for noise to be measured under real-world processing conditions, accounts for all sources of noise, and is predictive of internal noise audibility. PMID:20370034

  14. Fighting noise with noise: Where the contest stands for powerplant applications

    SciTech Connect

    O'Keefe, W.

    1994-07-01

    This article examines the use of active noise cancellation in power plant applications. The article examines the basic concepts of active noise cancellation, types of controls and generators for the canceling noise, economic trade-off, noise regulations, working conditions and impact to employees, demonstration projects and commercial applications.

  15. Adaptive subspace detection of extended target in white Gaussian noise using sinc basis

    NASA Astrophysics Data System (ADS)

    Zhang, Xiao-Wei; Li, Ming; Qu, Jian-She; Yang, Hui

    2016-01-01

    For the high resolution radar (HRR), the problem of detecting the extended target is considered in this paper. Based on a single observation, a new two-step detection based on sparse representation (TSDSR) method is proposed to detect the extended target in the presence of Gaussian noise with unknown covariance. In the new method, the Sinc dictionary is introduced to sparsely represent the high resolution range profile (HRRP). Meanwhile, adaptive subspace pursuit (ASP) is presented to recover the HRRP embedded in the Gaussian noise and estimate the noise covariance matrix. Based on the Sinc dictionary and the estimated noise covariance matrix, one step subspace detector (OSSD) for the first-order Gaussian (FOG) model without secondary data is adopted to realise the extended target detection. Finally, the proposed TSDSR method is applied to raw HRR data. Experimental results demonstrate that HRRPs of different targets can be sparsely represented very well with the Sinc dictionary. Moreover, the new method can estimate the noise power with tiny errors and have a good detection performance.

  16. Adaptive noise suppression technique for dense 3D point cloud reconstructions from monocular vision

    NASA Astrophysics Data System (ADS)

    Diskin, Yakov; Asari, Vijayan K.

    2012-10-01

    Mobile vision-based autonomous vehicles use video frames from multiple angles to construct a 3D model of their environment. In this paper, we present a post-processing adaptive noise suppression technique to enhance the quality of the computed 3D model. Our near real-time reconstruction algorithm uses each pair of frames to compute the disparities of tracked feature points to translate the distance a feature has traveled within the frame in pixels into real world depth values. As a result these tracked feature points are plotted to form a dense and colorful point cloud. Due to the inevitable small vibrations in the camera and the mismatches within the feature tracking algorithm, the point cloud model contains a significant amount of misplaced points appearing as noise. The proposed noise suppression technique utilizes the spatial information of each point to unify points of similar texture and color into objects while simultaneously removing noise dissociated with any nearby objects. The noise filter combines all the points of similar depth into 2D layers throughout the point cloud model. By applying erosion and dilation techniques we are able to eliminate the unwanted floating points while retaining points of larger objects. To reverse the compression process, we transform the 2D layer back into the 3D model allowing points to return to their original position without the attached noise components. We evaluate the resulting noiseless point cloud by utilizing an unmanned ground vehicle to perform obstacle avoidance tasks. The contribution of the noise suppression technique is measured by evaluating the accuracy of the 3D reconstruction.

  17. Adaptive control of interference at satellite earth stations

    NASA Astrophysics Data System (ADS)

    Carlin, J. W.; Chipaloski, A. C.; Steinberger, M. L.

    This paper presents system designs for adaptive interference cancellation at satellite earth stations. Cancellation systems to reduce co-frequency, foreign system (interference from terrestrial microwave radio systems) and adjacent satellite interference as well as interference from co-frequency, orthogonally polarized channels are considered. The systems employ common building blocks: rf weight circuits, an analog processor consisting of a multiplier and integrator, and a dither generator which provides multiple orthogonal sequences so that the rf weights in the cancellation network can be varied and optimized simultaneously. Measured data from field installations equipped with cross-pol. adjacent satellite and sidelobe cancellation systems is presented and discussed. The measured sidelobe canceler performance is compared with performance bounds calculated to result from tolerable circuit mismatches, thermal noise and 'power inversion' effects. The effect of multipath coupled interference is discussed and shown to be a significant factor which limits sidelobe canceler performance.

  18. A Robust Approach For Acoustic Noise Suppression In Speech Using ANFIS

    NASA Astrophysics Data System (ADS)

    Martinek, Radek; Kelnar, Michal; Vanus, Jan; Bilik, Petr; Zidek, Jan

    2015-11-01

    The authors of this article deals with the implementation of a combination of techniques of the fuzzy system and artificial intelligence in the application area of non-linear noise and interference suppression. This structure used is called an Adaptive Neuro Fuzzy Inference System (ANFIS). This system finds practical use mainly in audio telephone (mobile) communication in a noisy environment (transport, production halls, sports matches, etc). Experimental methods based on the two-input adaptive noise cancellation concept was clearly outlined. Within the experiments carried out, the authors created, based on the ANFIS structure, a comprehensive system for adaptive suppression of unwanted background interference that occurs in audio communication and degrades the audio signal. The system designed has been tested on real voice signals. This article presents the investigation and comparison amongst three distinct approaches to noise cancellation in speech; they are LMS (least mean squares) and RLS (recursive least squares) adaptive filtering and ANFIS. A careful review of literatures indicated the importance of non-linear adaptive algorithms over linear ones in noise cancellation. It was concluded that the ANFIS approach had the overall best performance as it efficiently cancelled noise even in highly noise-degraded speech. Results were drawn from the successful experimentation, subjective-based tests were used to analyse their comparative performance while objective tests were used to validate them. Implementation of algorithms was experimentally carried out in Matlab to justify the claims and determine their relative performances.

  19. Background Noise Mitigation in Deep-Space Optical Communications Using Adaptive Optics

    NASA Astrophysics Data System (ADS)

    Lee, S.; Wilson, K. E.; Troy, M.

    2005-05-01

    Over the last decade, adaptive optics technology has moved from the purview of a Department of Defense laboratory to astronomical telescopes around the world, and recently to industry, where adaptive optics systems have been developed to correct atmospheric-induced signal fades on high-bandwidth horizontal-path optical links. As JPL develops optical communications technology for high-bandwidth optical links from its deep-space probes, we are exploring the application of adaptive optics to the optical deep-space receiver to improve the quality of the link under turbulent atmospheric and high-background conditions. To provide maximum communications support, the operational deep-space optical communications receiver will need to point close to the Sun or to a bright Sun-illuminated planet. Under these conditions, the background noise from the sky degrades the quality of the optical link, especially when the atmospheric seeing is poor. In this work, we analyze how adaptive optics could be used to mitigate the effects of sky and planetary background noise on the deep-space optical communications receiver's performance in poor seeing conditions. Our results show that, under nominal background sky conditions, gains of 4 dB can be achieved for the uncoded bit-error rate of 0.01.

  20. A new time-adaptive discrete bionic wavelet transform for enhancing speech from adverse noise environment

    NASA Astrophysics Data System (ADS)

    Palaniswamy, Sumithra; Duraisamy, Prakash; Alam, Mohammad Showkat; Yuan, Xiaohui

    2012-04-01

    Automatic speech processing systems are widely used in everyday life such as mobile communication, speech and speaker recognition, and for assisting the hearing impaired. In speech communication systems, the quality and intelligibility of speech is of utmost importance for ease and accuracy of information exchange. To obtain an intelligible speech signal and one that is more pleasant to listen, noise reduction is essential. In this paper a new Time Adaptive Discrete Bionic Wavelet Thresholding (TADBWT) scheme is proposed. The proposed technique uses Daubechies mother wavelet to achieve better enhancement of speech from additive non- stationary noises which occur in real life such as street noise and factory noise. Due to the integration of human auditory system model into the wavelet transform, bionic wavelet transform (BWT) has great potential for speech enhancement which may lead to a new path in speech processing. In the proposed technique, at first, discrete BWT is applied to noisy speech to derive TADBWT coefficients. Then the adaptive nature of the BWT is captured by introducing a time varying linear factor which updates the coefficients at each scale over time. This approach has shown better performance than the existing algorithms at lower input SNR due to modified soft level dependent thresholding on time adaptive coefficients. The objective and subjective test results confirmed the competency of the TADBWT technique. The effectiveness of the proposed technique is also evaluated for speaker recognition task under noisy environment. The recognition results show that the TADWT technique yields better performance when compared to alternate methods specifically at lower input SNR.

  1. PLI cancellation in ECG signal based on adaptive filter by using Wiener-Hopf equation for providing initial condition.

    PubMed

    Manosueb, Anchalee; Koseeyaporn, Jeerasuda; Wardkein, Paramote

    2014-01-01

    This paper presents a technique for finding the optimal initial weight for adaptive filter by using difference equation. The obtained analytical response of the system identifies the appropriate weights for the system and shows that the MSE depends on the initial weight. The proposed technique is applied to eliminate the known frequency power line interference (PLI) signal in the electrocardiogram (ECG) signal. The PLI signal is considered as a combination of cosine and sine signals. The adaptive filter, therefore, attempts to adjust the amplitude of cosine and sine signals to synthesize a reference signal very similar to the contaminated PLI signal. To compare the potential of the proposed technique to other techniques, the system is simulated by using the Matlab program and the TMS320C6713 digital board. The simulation results demonstrate that the proposed technique enables the system to eliminate the PLI signal with the fastest time and gains the superior results of the recovered ECG signal.

  2. Adaptive control of stochastic Hammerstein-Wiener nonlinear systems with measurement noise

    NASA Astrophysics Data System (ADS)

    Zhang, Bi; Mao, Zhizhong

    2016-01-01

    This paper deals with the adaptive control of a class of stochastic Hammerstein-Wiener nonlinear systems with measurement noise. Despite the fundamental progress achieved so far, a general theory framework about adaptive control of Hammerstein-Wiener models is still absent. Such situation is mainly due to the lack of an appropriate parameterisation model. To this end, this paper presents a novel parameterisation model that is to replace unmeasurable internal variables with their estimations. Then, the adaptive control algorithm to be applied is derived on the basis of self-tuning control. In addition, due to the use of the internal variable estimations, the stability and convergence properties are different from the self-tuning control. Our aim, in theoretical analysis, is to discover what limitations are in using the estimations instead of the true values in a control algorithm. Representative numerical examples are given and the simulation results verify the theoretical analysis.

  3. Impulse noise removal using 1-D switching median filter with adaptive scanning order based on structural context of image

    NASA Astrophysics Data System (ADS)

    Koga, Takanori; Suetake, Noriaki

    2015-02-01

    This paper describes the detail-preserving impulse noise removal performance of a one-dimensional (1-D) switching median filter (SMF) applied along an adaptive space-filling curve. Usually, a SMF with a two-dimensional (2-D) filter window is widely used for impulse noise removal while still preserving detailed parts in an input image. However, the noise detector of the 2-D filter does not always distinguish between the original pixels and the noise-corrupted ones perfectly. In particular, pixels constituting thin lines in an input image tend to be incorrectly detected as noise-corrupted pixels, and such pixels are filtered regardless of the necessity of the filtering. To cope with this problem, we propose a new impulse noise removal method based on a 1-D SMF and a space-filling curve which is adaptively drawn using a minimum spanning tree reflecting structural context of an input image.

  4. Adaptive step-size strategy for noise-robust Fourier ptychographic microscopy.

    PubMed

    Zuo, Chao; Sun, Jiasong; Chen, Qian

    2016-09-01

    The incremental gradient approaches, such as PIE and ePIE, are widely used in the field of ptychographic imaging due to their great flexibility and computational efficiency. Nevertheless, their stability and reconstruction quality may be significantly degraded when non-negligible noise is present in the image. Though this problem is often attributed to the non-convex nature of phase retrieval, we found the reason for this is more closely related to the choice of the step-size, which needs to be gradually diminishing for convergence even in the convex case. To this end, we introduce an adaptive step-size strategy that decreases the step-size whenever sufficient progress is not made. The synthetic and real experiments on Fourier ptychographic microscopy show that the adaptive step-size strategy significantly improves the stability and robustness of the reconstruction towards noise yet retains the fast initial convergence speed of PIE and ePIE. More importantly, the proposed approach is simple, nonparametric, and does not require any preknowledge about the noise statistics. The great performance and limited computational complexity make it a very attractive and promising technique for robust Fourier ptychographic microscopy under noisy conditions. PMID:27607676

  5. Study of active noise control system for a commercial HVAC unit

    NASA Astrophysics Data System (ADS)

    Devineni, Naga

    Acoustic noise is a common problem in everyday life. If the appliances that are present in the work and living areas generate noise then it's a serious problem. One such appliance is the Heating, Ventilation and Air-conditioning system (HVAC) in which blower fan and compressor units are housed together. Operation of a HVAC system creates two kinds of noise. One is the noise due to the air flow and the other is the result of the compressor. Both of them exhibit different signal properties and need different strategies to control them. There has been previous efforts in designing noise control systems that can control noise from the HVAC system. These include passive methods which use sound absorption materials to attenuate noise and active methods which cancel noise by generating anti-noise. Passive methods are effective in limiting the high frequency noise, but are inefficient in controlling low frequency noise from the compressor. Compressor noise is one of the strong low frequency components that propagate through the walls, therefore there is need for deploying active signal processing methods that consider the signal properties into consideration to cancel the noise acoustically. The quasi periodic nature of the compressor noise is exploited in noise modeling which aids in implementing an adaptive linear prediction filter in estimating the anti noise [12]. In this thesis, a multi channel architecture has been studied for a specific HVAC system in order to improve noise cancellation by creating larger quiet zone. In addition to the multi-channel architecture, a real time narrow band Active Noise Control (ANC) was employed to cancel noise under practical conditions.

  6. Multi-microphone adaptive noise reduction strategies for coordinated stimulation in bilateral cochlear implant devices.

    PubMed

    Kokkinakis, Kostas; Loizou, Philipos C

    2010-05-01

    Bilateral cochlear implant (BI-CI) recipients achieve high word recognition scores in quiet listening conditions. Still, there is a substantial drop in speech recognition performance when there is reverberation and more than one interferers. BI-CI users utilize information from just two directional microphones placed on opposite sides of the head in a so-called independent stimulation mode. To enhance the ability of BI-CI users to communicate in noise, the use of two computationally inexpensive multi-microphone adaptive noise reduction strategies exploiting information simultaneously collected by the microphones associated with two behind-the-ear (BTE) processors (one per ear) is proposed. To this end, as many as four microphones are employed (two omni-directional and two directional) in each of the two BTE processors (one per ear). In the proposed two-microphone binaural strategies, all four microphones (two behind each ear) are being used in a coordinated stimulation mode. The hypothesis is that such strategies combine spatial information from all microphones to form a better representation of the target than that made available with only a single input. Speech intelligibility is assessed in BI-CI listeners using IEEE sentences corrupted by up to three steady speech-shaped noise sources. Results indicate that multi-microphone strategies improve speech understanding in single- and multi-noise source scenarios.

  7. Implementation for temporal noise identification using adaptive threshold of infrared imaging system

    NASA Astrophysics Data System (ADS)

    Lim, Inok

    2007-10-01

    Bad pixels are spatial or temporal noise which arise from dead pixels by fixed signal levels or blinking pixels by variable signal levels that go beyond the bounds of normal pixel levels at the temperature. Because bad pixels are the false targets over infrared imaging system for tracking, those must be corrected. Main contribution to the number of bad pixels is fixed pattern noise (FPN) according to increasing array size. And it is more simple to establish whether FPN is or not through analyzing of accumulated frames. But it needs to calculate with more complex implementation such standard deviation from frame to frame in case of the temporal noise. Both cases it is very important to establish the threshold levels for identifying at variable operating temperatures. In this paper, we propose a more efficient data analysis method and a temporal noise identification method using adaptive threshold for infrared imaging system, and the hardware is implemented to identify and replace bad pixels. And its result is confirmed visually by bad pixel map images.

  8. PHYCAA+: an optimized, adaptive procedure for measuring and controlling physiological noise in BOLD fMRI.

    PubMed

    Churchill, Nathan W; Strother, Stephen C

    2013-11-15

    The presence of physiological noise in functional MRI can greatly limit the sensitivity and accuracy of BOLD signal measurements, and produce significant false positives. There are two main types of physiological confounds: (1) high-variance signal in non-neuronal tissues of the brain including vascular tracts, sinuses and ventricles, and (2) physiological noise components which extend into gray matter tissue. These physiological effects may also be partially coupled with stimuli (and thus the BOLD response). To address these issues, we have developed PHYCAA+, a significantly improved version of the PHYCAA algorithm (Churchill et al., 2011) that (1) down-weights the variance of voxels in probable non-neuronal tissue, and (2) identifies the multivariate physiological noise subspace in gray matter that is linked to non-neuronal tissue. This model estimates physiological noise directly from EPI data, without requiring external measures of heartbeat and respiration, or manual selection of physiological components. The PHYCAA+ model significantly improves the prediction accuracy and reproducibility of single-subject analyses, compared to PHYCAA and a number of commonly-used physiological correction algorithms. Individual subject denoising with PHYCAA+ is independently validated by showing that it consistently increased between-subject activation overlap, and minimized false-positive signal in non gray-matter loci. The results are demonstrated for both block and fast single-event task designs, applied to standard univariate and adaptive multivariate analysis models.

  9. Seismic random noise attenuation based on adaptive time-frequency peak filtering

    NASA Astrophysics Data System (ADS)

    Deng, Xinhuan; Ma, Haitao; Li, Yue; Zeng, Qian

    2015-02-01

    Time-frequency peak filtering (TFPF) method uses a specific window with fixed length to recover band-limited signal in stationary random noise. However, the derivatives of signal such as seismic wavelets may change rapidly in some short time intervals. In this case, TFPF equipped with fixed window length will not provide an optimal solution. In this letter, we present an adaptive version of TFPF for seismic random noise attenuation. In our version, the improved intersection of confidence intervals combined with short-time energy criterion is used to preprocess the noisy signal. And then, we choose an appropriate threshold to divide the noisy signal into signal, buffer and noise. Different optimal window lengths are used in each type of segments. We test the proposed method on both synthetic and field seismic data. The experimental results illustrate that the proposed method makes the degree of amplitude preservation raise more than 10% and signal-to-noise (SNR) improve 2-4 dB compared with the original algorithm.

  10. Three-dimensional anisotropic adaptive filtering of projection data for noise reduction in cone beam CT

    SciTech Connect

    Maier, Andreas; Wigstroem, Lars; Hofmann, Hannes G.; Hornegger, Joachim; Zhu Lei; Strobel, Norbert; Fahrig, Rebecca

    2011-11-15

    Purpose: The combination of quickly rotating C-arm gantry with digital flat panel has enabled the acquisition of three-dimensional data (3D) in the interventional suite. However, image quality is still somewhat limited since the hardware has not been optimized for CT imaging. Adaptive anisotropic filtering has the ability to improve image quality by reducing the noise level and therewith the radiation dose without introducing noticeable blurring. By applying the filtering prior to 3D reconstruction, noise-induced streak artifacts are reduced as compared to processing in the image domain. Methods: 3D anisotropic adaptive filtering was used to process an ensemble of 2D x-ray views acquired along a circular trajectory around an object. After arranging the input data into a 3D space (2D projections + angle), the orientation of structures was estimated using a set of differently oriented filters. The resulting tensor representation of local orientation was utilized to control the anisotropic filtering. Low-pass filtering is applied only along structures to maintain high spatial frequency components perpendicular to these. The evaluation of the proposed algorithm includes numerical simulations, phantom experiments, and in-vivo data which were acquired using an AXIOM Artis dTA C-arm system (Siemens AG, Healthcare Sector, Forchheim, Germany). Spatial resolution and noise levels were compared with and without adaptive filtering. A human observer study was carried out to evaluate low-contrast detectability. Results: The adaptive anisotropic filtering algorithm was found to significantly improve low-contrast detectability by reducing the noise level by half (reduction of the standard deviation in certain areas from 74 to 30 HU). Virtually no degradation of high contrast spatial resolution was observed in the modulation transfer function (MTF) analysis. Although the algorithm is computationally intensive, hardware acceleration using Nvidia's CUDA Interface provided an 8.9-fold

  11. Adaptive ambient noise tomography and its application to the Garlock Fault, southern California

    NASA Astrophysics Data System (ADS)

    Li, Peng; Lin, Guoqing

    2014-05-01

    Traditional ambient noise tomography methods using regular grid nodes are often ill posed because the inversion grids do not always represent the distribution of ray paths. Large grid spacing is usually used to reduce the number of inversion parameters, which may not be able to solve for small-scale velocity structure. We present a new adaptive tomography method with irregular grids that provides a few advantages over the traditional methods. First, irregular grids with different sizes and shapes can fit the ray distribution better and the traditionally ill-posed problem can become more stable owing to the different parametrizations. Secondly, the data in the area with dense ray sampling will be sufficiently utilized so that the model resolution can be greatly improved. Both synthetic and real data are used to test the newly developed tomography algorithm. In synthetic data tests, we compare the resolution and stability of the traditional and adaptive methods. The results show that adaptive tomography is more stable and performs better in improving the resolution in the area with dense ray sampling. For real data, we extract the ambient noise signals of the seismic data near the Garlock Fault region, obtained from the Southern California Earthquake Data Center. The resulting group velocity of Rayleigh wave is well correlated with the geological structures. High-velocity anomalies are shown in the cold southern Sierra Nevada, the Tehachapi Mountains and the Western San Gabriel Mountains. In contrast, low velocity values are prominent in the southern San Joaquin Valley and western Mojave.

  12. Adaptive Helmholtz resonators and passive vibration absorbers for cylinder interior noise control

    NASA Astrophysics Data System (ADS)

    Estève, Simon J.; Johnson, Marty E.

    2005-12-01

    This paper presents an adaptive-passive solution to control the broadband sound transmission into rocket payload fairings. The treatment is composed of passive distributed vibration absorbers (DVAs) and adaptive Helmholtz resonators (HR). Both the frequency domain and time-domain model of a simply supported cylinder excited by an external plane wave are developed. To tune vibration absorbers to tonal excitation, a tuning strategy, based on the phase information between the velocity of the absorber mass and the velocity of the host structure is used here in a new fashion to tune resonators to peaks in the broadband acoustic spectrum of a cavity. This tuning law, called the dot-product method, only uses two microphone signals local to each HR, which allows the adaptive Helmholtz resonator (AHR) to be manufactured as an autonomous device with power supply, sensor, actuator and controller integrated. Numerical simulations corresponding to a 2.8 m long 2.5 m diameter composite cylinder prototype demonstrate that, as long as the structure modes, which strongly couple to the acoustic cavity, are damped with a DVA treatment, the dot-product method tune multiple HRs to a near-optimal solution over a broad frequency range (40-160 Hz). An adaptive HR prototype with variable opening is built and characterized. Experiments conducted on the cylinder prototype with eight AHRs demonstrate the ability of resonators adapted with the dot-product method to converge to near-optimal noise attenuation in a frequency band including multiple resonances.

  13. Adaptive box filters for removal of random noise from digital images

    NASA Technical Reports Server (NTRS)

    Eliason, Eric M.; Mcewen, Alfred S.

    1990-01-01

    Adaptive box-filtering algorithms to remove random bit errors and to smooth noisy data have been developed. For both procedures, the standard deviation of those pixels within a local box surrounding each pixel is used. A series of two or three filters with decreasing box sizes can be run to clean up extremely noisy images and to remove bit errors near sharp edges. The second filter, for noise smoothing, is similar to the 'sigma filter' of Lee (1983). The technique effectively reduces speckle in radar images without eliminating fine details.

  14. A model for radar images and its application to adaptive digital filtering of multiplicative noise.

    PubMed

    Frost, V S; Stiles, J A; Shanmugan, K S; Holtzman, J C

    1982-02-01

    Standard image processing techniques which are used to enhance noncoherent optically produced images are not applicable to radar images due to the coherent nature of the radar imaging process. A model for the radar imaging process is derived in this paper and a method for smoothing noisy radar images is also presented. The imaging model shows that the radar image is corrupted by multiplicative noise. The model leads to the functional form of an optimum (minimum MSE) filter for smoothing radar images. By using locally estimated parameter values the filter is made adaptive so that it provides minimum MSE estimates inside homogeneous areas of an image while preserving the edge structure. It is shown that the filter can be easily implemented in the spatial domain and is computationally efficient. The performance of the adaptive filter is compared (qualitatively and quantitatively) with several standard filters using real and simulated radar images.

  15. Speech Enhancement, Gain, and Noise Spectrum Adaptation Using Approximate Bayesian Estimation.

    PubMed

    Hao, Jiucang; Attias, Hagai; Nagarajan, Srikantan; Lee, Te-Won; Sejnowski, Terrence J

    2009-01-01

    This paper presents a new approximate Bayesian estimator for enhancing a noisy speech signal. The speech model is assumed to be a Gaussian mixture model (GMM) in the log-spectral domain. This is in contrast to most current models in frequency domain. Exact signal estimation is a computationally intractable problem. We derive three approximations to enhance the efficiency of signal estimation. The Gaussian approximation transforms the log-spectral domain GMM into the frequency domain using minimal Kullback-Leiber (KL)-divergency criterion. The frequency domain Laplace method computes the maximum a posteriori (MAP) estimator for the spectral amplitude. Correspondingly, the log-spectral domain Laplace method computes the MAP estimator for the log-spectral amplitude. Further, the gain and noise spectrum adaptation are implemented using the expectation-maximization (EM) algorithm within the GMM under Gaussian approximation. The proposed algorithms are evaluated by applying them to enhance the speeches corrupted by the speech-shaped noise (SSN). The experimental results demonstrate that the proposed algorithms offer improved signal-to-noise ratio, lower word recognition error rate, and less spectral distortion. PMID:20428253

  16. Neural Mechanisms Behind Identification of Leptokurtic Noise and Adaptive Behavioral Response.

    PubMed

    d'Acremont, Mathieu; Bossaerts, Peter

    2016-04-01

    Large-scale human interaction through, for example, financial markets causes ceaseless random changes in outcome variability, producing frequent and salient outliers that render the outcome distribution more peaked than the Gaussian distribution, and with longer tails. Here, we study how humans cope with this evolutionary novel leptokurtic noise, focusing on the neurobiological mechanisms that allow the brain, 1) to recognize the outliers as noise and 2) to regulate the control necessary for adaptive response. We used functional magnetic resonance imaging, while participants tracked a target whose movements were affected by leptokurtic noise. After initial overreaction and insufficient subsequent correction, participants improved performance significantly. Yet, persistently long reaction times pointed to continued need for vigilance and control. We ran a contrasting treatment where outliers reflected permanent moves of the target, as in traditional mean-shift paradigms. Importantly, outliers were equally frequent and salient. There, control was superior and reaction time was faster. We present a novel reinforcement learning model that fits observed choices better than the Bayes-optimal model. Only anterior insula discriminated between the 2 types of outliers. In both treatments, outliers initially activated an extensive bottom-up attention and belief network, followed by sustained engagement of the fronto-parietal control network.

  17. Neural Mechanisms Behind Identification of Leptokurtic Noise and Adaptive Behavioral Response

    PubMed Central

    d'Acremont, Mathieu; Bossaerts, Peter

    2016-01-01

    Large-scale human interaction through, for example, financial markets causes ceaseless random changes in outcome variability, producing frequent and salient outliers that render the outcome distribution more peaked than the Gaussian distribution, and with longer tails. Here, we study how humans cope with this evolutionary novel leptokurtic noise, focusing on the neurobiological mechanisms that allow the brain, 1) to recognize the outliers as noise and 2) to regulate the control necessary for adaptive response. We used functional magnetic resonance imaging, while participants tracked a target whose movements were affected by leptokurtic noise. After initial overreaction and insufficient subsequent correction, participants improved performance significantly. Yet, persistently long reaction times pointed to continued need for vigilance and control. We ran a contrasting treatment where outliers reflected permanent moves of the target, as in traditional mean-shift paradigms. Importantly, outliers were equally frequent and salient. There, control was superior and reaction time was faster. We present a novel reinforcement learning model that fits observed choices better than the Bayes-optimal model. Only anterior insula discriminated between the 2 types of outliers. In both treatments, outliers initially activated an extensive bottom-up attention and belief network, followed by sustained engagement of the fronto-parietal control network. PMID:26850528

  18. Use of Adaptive Digital Signal Processing to Improve Speech Communication for Normally Hearing aand Hearing-Impaired Subjects.

    ERIC Educational Resources Information Center

    Harris, Richard W.; And Others

    1988-01-01

    A two-microphone adaptive digital noise cancellation technique improved word-recognition ability for 20 normal and 12 hearing-impaired adults by reducing multitalker speech babble and speech spectrum noise 18-22 dB. Word recognition improvements averaged 37-50 percent for normal and 27-40 percent for hearing-impaired subjects. Improvement was best…

  19. Adaptive RSOV filter using the FELMS algorithm for nonlinear active noise control systems

    NASA Astrophysics Data System (ADS)

    Zhao, Haiquan; Zeng, Xiangping; He, Zhengyou; Li, Tianrui

    2013-01-01

    This paper presents a recursive second-order Volterra (RSOV) filter to solve the problems of signal saturation and other nonlinear distortions that occur in nonlinear active noise control systems (NANC) used for actual applications. Since this nonlinear filter based on an infinite impulse response (IIR) filter structure can model higher than second-order and third-order nonlinearities for systems where the nonlinearities are harmonically related, the RSOV filter is more effective in NANC systems with either a linear secondary path (LSP) or a nonlinear secondary path (NSP). Simulation results clearly show that the RSOV adaptive filter using the multichannel structure filtered-error least mean square (FELMS) algorithm can further greatly reduce the computational burdens and is more suitable to eliminate nonlinear distortions in NANC systems than a SOV filter, a bilinear filter and a third-order Volterra (TOV) filter.

  20. Communal Sensor Network for Adaptive Noise Reduction in Aircraft Engine Nacelles

    NASA Technical Reports Server (NTRS)

    Jones, Kennie H.; Nark, Douglas M.; Jones, Michael G.

    2011-01-01

    Emergent behavior, a subject of much research in biology, sociology, and economics, is a foundational element of Complex Systems Science and is apropos in the design of sensor network systems. To demonstrate engineering for emergent behavior, a novel approach in the design of a sensor/actuator network is presented maintaining optimal noise attenuation as an adaptation to changing acoustic conditions. Rather than use the conventional approach where sensors are managed by a central controller, this new paradigm uses a biomimetic model where sensor/actuators cooperate as a community of autonomous organisms, sharing with neighbors to control impedance based on local information. From the combination of all individual actions, an optimal attenuation emerges for the global system.

  1. Noise correlation-based adaptive polarimetric image representation for contrast enhancement of a polarized beacon in fog

    NASA Astrophysics Data System (ADS)

    Panigrahi, Swapnesh; Fade, Julien; Alouini, Mehdi

    2015-10-01

    We show the use of a simplified snapshot polarimetric camera along with an adaptive image processing for optimal detection of a polarized light beacon through fog. The adaptive representation is derived using theoretical noise analysis of the data at hand and is shown to be optimal in the Maximum likelihood sense. We report that the contrast enhancing optimal representation that depends on the background noise correlation differs in general from standard representations like polarimetric difference image or polarization filtered image. Lastly, we discuss a detection strategy to reduce the false positive counts.

  2. Improvement in DMSA imaging using adaptive noise reduction: an ROC analysis.

    PubMed

    Lorimer, Lisa; Gemmell, Howard G; Sharp, Peter F; McKiddie, Fergus I; Staff, Roger T

    2012-11-01

    Dimercaptosuccinic acid imaging is the 'gold standard' for the detection of cortical defects and diagnosis of scarring of the kidneys. The Siemens planar processing package, which implements adaptive noise reduction using the Pixon algorithm, is designed to allow a reduction in image noise, enabling improved image quality and reduced acquisition time/injected activity. This study aimed to establish the level of improvement in image quality achievable using this algorithm. Images were acquired of a phantom simulating a single kidney with a range of defects of varying sizes, positions and contrasts. These images were processed using the Pixon processing software and shown to 12 observers (six experienced and six novices) who were asked to rate the images on a six-point scale depending on their confidence that a defect was present. The data were analysed using a receiver operating characteristic approach. Results showed that processed images significantly improved the performance of the experienced observers in terms of their sensitivity and specificity. Although novice observers showed significant increase in sensitivity when using the software, a significant decrease in specificity was also seen. This study concludes that the Pixon software can be used to improve the assessment of cortical defects in dimercaptosuccinic acid imaging by suitably trained observers.

  3. Neuromorphic learning of continuous-valued mappings from noise-corrupted data. Application to real-time adaptive control

    NASA Technical Reports Server (NTRS)

    Troudet, Terry; Merrill, Walter C.

    1990-01-01

    The ability of feed-forward neural network architectures to learn continuous valued mappings in the presence of noise was demonstrated in relation to parameter identification and real-time adaptive control applications. An error function was introduced to help optimize parameter values such as number of training iterations, observation time, sampling rate, and scaling of the control signal. The learning performance depended essentially on the degree of embodiment of the control law in the training data set and on the degree of uniformity of the probability distribution function of the data that are presented to the net during sequence. When a control law was corrupted by noise, the fluctuations of the training data biased the probability distribution function of the training data sequence. Only if the noise contamination is minimized and the degree of embodiment of the control law is maximized, can a neural net develop a good representation of the mapping and be used as a neurocontroller. A multilayer net was trained with back-error-propagation to control a cart-pole system for linear and nonlinear control laws in the presence of data processing noise and measurement noise. The neurocontroller exhibited noise-filtering properties and was found to operate more smoothly than the teacher in the presence of measurement noise.

  4. Adaptive approach for variable noise suppression on laser-induced breakdown spectroscopy responses using stationary wavelet transform.

    PubMed

    Schlenke, Jan; Hildebrand, Lars; Moros, Javier; Laserna, J Javier

    2012-11-19

    Spectral signals are often corrupted by noise during their acquisition and transmission. Signal processing refers to a variety of operations that can be carried out on measurements in order to enhance the quality of information. In this sense, signal denoising is used to reduce noise distortions while keeping alterations of the important signal features to a minimum. The minimization of noise is a highly critical task since, in many cases, there is no prior knowledge of the signal or of the noise. In the context of denoising, wavelet transformation has become a valuable tool. The present paper proposes a noise reduction technique for suppressing noise in laser-induced breakdown spectroscopy (LIBS) signals using wavelet transform. An extension of the Donoho's scheme, which uses a redundant form of wavelet transformation and an adaptive threshold estimation method, is suggested. Capabilities and results achieved on denoising processes of artificial signals and actual spectroscopic data, both corrupted by noise with changing intensities, are presented. In order to better consolidate the gains so far achieved by the proposed strategy, a comparison with alternative approaches, as well as with traditional techniques, is also made.

  5. Practical Study and Solutions Adapted For The Road Noise In The Algiers City

    NASA Astrophysics Data System (ADS)

    Iddir, R.; Boukhaloua, N.; Saadi, T.

    At the present hour where the city spreads on a big space, the road network devel- opment was a following logical of this movement. Generating a considerable impact thus on the environment. This last is a resulting open system of the interaction be- tween the man and the nature, it's affected all side by the different means of transport and by their increasing demand of mobility. The contemporary city development be- got problems bound to the environment and among it : The road noise. This last is a complex phenomenon, essentially by reason of its humans sensory effects, its impact on the environment is considerable, this one concerns the life quality directly, mainly in population zones to strong density. The resonant pollution reached its paroxysm; the road network of Algiers is not conceived to satisfy requirements in resonant pol- lution matter. For it arrangements soundproof should be adapted in order to face of it these new requirements in matter of the acoustic comfort. All these elements drove to the process aiming the attenuation of the hindrance caused by the road traffic and it by actions essentially aiming: vehicles, the structure of the road and the immediate envi- ronment of the system road - structure. From these results, we note that the situation in resonant nuisance matter in this zone with strong traffic is disturbing, and especially on the residents health.

  6. A de-noising algorithm based on wavelet threshold-exponential adaptive window width-fitting for ground electrical source airborne transient electromagnetic signal

    NASA Astrophysics Data System (ADS)

    Ji, Yanju; Li, Dongsheng; Yu, Mingmei; Wang, Yuan; Wu, Qiong; Lin, Jun

    2016-05-01

    The ground electrical source airborne transient electromagnetic system (GREATEM) on an unmanned aircraft enjoys considerable prospecting depth, lateral resolution and detection efficiency, etc. In recent years it has become an important technical means of rapid resources exploration. However, GREATEM data are extremely vulnerable to stationary white noise and non-stationary electromagnetic noise (sferics noise, aircraft engine noise and other human electromagnetic noises). These noises will cause degradation of the imaging quality for data interpretation. Based on the characteristics of the GREATEM data and major noises, we propose a de-noising algorithm utilizing wavelet threshold method and exponential adaptive window width-fitting. Firstly, the white noise is filtered in the measured data using the wavelet threshold method. Then, the data are segmented using data window whose step length is even logarithmic intervals. The data polluted by electromagnetic noise are identified within each window based on the discriminating principle of energy detection, and the attenuation characteristics of the data slope are extracted. Eventually, an exponential fitting algorithm is adopted to fit the attenuation curve of each window, and the data polluted by non-stationary electromagnetic noise are replaced with their fitting results. Thus the non-stationary electromagnetic noise can be effectively removed. The proposed algorithm is verified by the synthetic and real GREATEM signals. The results show that in GREATEM signal, stationary white noise and non-stationary electromagnetic noise can be effectively filtered using the wavelet threshold-exponential adaptive window width-fitting algorithm, which enhances the imaging quality.

  7. Slower Visuomotor Corrections with Unchanged Latency are Consistent with Optimal Adaptation to Increased Endogenous Noise in the Elderly

    PubMed Central

    Sherback, Michael; Valero-Cuevas, Francisco J.; D'Andrea, Raffaello

    2010-01-01

    We analyzed age-related changes in motor response in a visuomotor compensatory tracking task. Subjects used a manipulandum to attempt to keep a displayed cursor at the center of a screen despite random perturbations to its location. Cross-correlation analysis of the perturbation and the subject response showed no age-related increase in latency until the onset of response to the perturbation, but substantial slowing of the response itself. Results are consistent with age-related deterioration in the ratio of signal to noise in visuomotor response. The task is such that it is tractable to use Bayesian and quadratic optimality assumptions to construct a model for behavior. This model assumes that behavior resembles an optimal controller subject to noise, and parametrizes response in terms of latency, willingness to expend effort, noise intensity, and noise bandwidth. The model is consistent with the data for all young (n = 12, age 20–30) and most elderly (n = 12, age 65–92) subjects. The model reproduces the latency result from the cross-correlation method. When presented with increased noise, the computational model reproduces the experimentally observed age-related slowing and the observed lack of increased latency. The model provides a precise way to quantitatively formulate the long-standing hypothesis that age-related slowing is an adaptation to increased noise. PMID:20300648

  8. Using A-weighting for psychoacoustic active noise control.

    PubMed

    Bao, Hua; Panahi, Issa M S

    2009-01-01

    Conventional adaptive active noise control (ANC) methods aim to attenuate the acoustic noise over the frequency band of interest indiscriminately using the sound pressure level (SPL) measurement (or the measurement of the residual error variance). However, SPL does not correctly reflect the human perception of attenuated noise due to the frequency selective sensitivity of human hearing system. A-weighting is a commonly used weighting filter for measuring the noise. This weighting filter quantifies frequency response of the human ears and hearing system. In this paper, we aim to improve the performance of adaptive noise cancellation method from the psychoacoustic point of view by incorporating the A-weighting into the ANC system design. Loudness is used as the psychoacoustic criterion for evaluating the ANC system performance. Simulation results illustrate the effectiveness of the proposed method. PMID:19963645

  9. Visual acuity-adaptive detail enhancement and shadow noise reduction for iCAM06-based HDR imaging

    NASA Astrophysics Data System (ADS)

    Lee, Geun-Young; Lee, Sung-Hak; Kwon, Hyuk-Ju; Sohng, Kyu-Ik

    2015-04-01

    An image appearance model is extremely useful for high-dynamic-range image (HDRI) rendering. However, the base-detail separation and the tone compression process for tonal control cause degradations in image quality. This study focuses on the de-saturation, reduced contrast, and noise problems in dark regions that occur through HDRI-rendering. First, we discuss de-saturation compensation using a bilateral filter that is based on the visual acuity characteristics of various illuminant levels. The edge stop function of the bilateral filter in iCAM06 is adaptively modified according to the illuminant information. Second, to reduce the magnified noise in the dark regions caused by tone mapping, the shadow regions are detected by an object's intensity and illuminant level, and then the noise of the detected regions is reduced using a luminance-adaptive coring function. Finally, we confirmed the enhanced color saturation, image contrast, and reduced noise in shadow regions through the application of the proposed methods.

  10. Adaptive beamforming at very low frequencies in spatially coherent, cluttered noise environments with low signal-to-noise ratio and finite-averaging times

    PubMed

    Nuttall; Wilson

    2000-11-01

    Realistic simulations with spatially coherent noise have been run in order to compare the performance of adaptive beamforming (ABF), inverse beamforming (IBF), and conventional beamforming (CBF) for the case of finite-averaging times, where the actual spatial coherence of the acoustic field, or covariance matrix, is not known a priori, but must be estimated. These estimation errors cause large errors in the ABF estimate of the directionality of the acoustic field, partly because ABF is a highly nonlinear algorithm. In addition, it is shown that ABF is fundamentally limited in its suppression capability at very low frequency (VLF), based on the sidelobe level of the conventional beampattern in the direction of the noise interferer [G. L. Mohnkern, "Effects of Errors and Limitations on Interference Suppression," NOSC Technical Document 1478, Naval Ocean Systems Center (1989)]. The simulations include a low-level plane wave signal of interest, a stronger noise plane wave interferer, and spatially random background noise. Both IBF and ABF performed significantly better than CBF, and IBF's performance was slightly better than ABF's performance. The performances of IBF and the ABF algorithm, the minimum variance distortionless response (MVDR) [A. H. Nuttall and D. W. Hyde, "Unified Approach to Optimum and Suboptimum Processing for Arrays," USL Report Number 992, Naval Underwater Systems Center, New London, CT (22 April 1969)] were recently compared independently [J. S. D. Solomon, A. J. Knight, and M. V. Greening, "Sonar Array Signal Processing for Sparse Linear Arrays," Defense Science and Technology Organization (DSTO) Technical Report (June 1999)] using measured data, with the result that IBF outperformed MVDR. This result is significant because MVDR requires orders of magnitude more processing power than IBF or CBF.

  11. [Comparison of mating calls and adaptive strategies of Amolops wuyiensis and Odorrana tormotus (Anura) in noise-controlled environments].

    PubMed

    Zhang, Fang; Chen, Pan; Zhao, Shu-Yi

    2013-06-01

    In order to understand the acoustic characteristics and adaptive strategies of sympatric male Amolops wuyiensis and male Odorrana tormotus in environments controlled for high noise levels, we recorded and analyzed the advertisement calls produced by individual males during breeding season. The results show that A. wuyiensis produced a single type of call composed of variable syllables (from 3 to 6 syllables) with 2~10 pulses over different time periods. The average values of call duration, dominant frequency and signal noise ratio were 2 198.20 ms, 2 231.90 Hz and 33.00 dB respectively. There were no ultrasonic elements in A. wuyiensis calls and they did not have the basis of ultrasonic communication. The average values of call duration, dominant frequency and signal noise ratio of O. tormotus were 331.80 ms, 6 665.50 Hz and 37.00 dB respectively. Call structure of O. tormotus was consistent with previous studies. The noise did not mask the calls from the male A. wuyiensis and male O. tormotus, which have higher frequencies and amplitudes. To fulfill the intra-species communication in a noise-controlled environment, the A. wuyiensis male, which has a low vocal frequency and long transmission length, varied vocal frequency, composition, and duration, the latter of which serves to attract females. By contrast, the male O. tormotus increased vocal frequency, which reduces the energy expended on intra-species communication.

  12. Computed Tomography Images De-noising using a Novel Two Stage Adaptive Algorithm

    PubMed Central

    Fadaee, Mojtaba; Shamsi, Mousa; Saberkari, Hamidreza; Sedaaghi, Mohammad Hossein

    2015-01-01

    In this paper, an optimal algorithm is presented for de-noising of medical images. The presented algorithm is based on improved version of local pixels grouping and principal component analysis. In local pixels grouping algorithm, blocks matching based on L2 norm method is utilized, which leads to matching performance improvement. To evaluate the performance of our proposed algorithm, peak signal to noise ratio (PSNR) and structural similarity (SSIM) evaluation criteria have been used, which are respectively according to the signal to noise ratio in the image and structural similarity of two images. The proposed algorithm has two de-noising and cleanup stages. The cleanup stage is carried out comparatively; meaning that it is alternately repeated until the two conditions based on PSNR and SSIM are established. Implementation results show that the presented algorithm has a significant superiority in de-noising. Furthermore, the quantities of SSIM and PSNR values are higher in comparison to other methods. PMID:26955565

  13. High-order total variation-based multiplicative noise removal with spatially adapted parameter selection.

    PubMed

    Liu, Jun; Huang, Ting-Zhu; Xu, Zongben; Lv, Xiao-Guang

    2013-10-01

    Multiplicative noise is one common type of noise in imaging science. For coherent image-acquisition systems, such as synthetic aperture radar, the observed images are often contaminated by multiplicative noise. Total variation (TV) regularization has been widely researched for multiplicative noise removal in the literature due to its edge-preserving feature. However, the TV-based solutions sometimes have an undesirable staircase artifact. In this paper, we propose a model to take advantage of the good nature of the TV norm and high-order TV norm to balance the edge and smoothness region. Besides, we adopt a spatially regularization parameter updating scheme. Numerical results illustrate the efficiency of our method in terms of the signal-to-noise ratio and structure similarity index.

  14. An Adaptive Wavelet-Based Denoising Algorithm for Enhancing Speech in Non-stationary Noise Environment

    NASA Astrophysics Data System (ADS)

    Wang, Kun-Ching

    Traditional wavelet-based speech enhancement algorithms are ineffective in the presence of highly non-stationary noise because of the difficulties in the accurate estimation of the local noise spectrum. In this paper, a simple method of noise estimation employing the use of a voice activity detector is proposed. We can improve the output of a wavelet-based speech enhancement algorithm in the presence of random noise bursts according to the results of VAD decision. The noisy speech is first preprocessed using bark-scale wavelet packet decomposition (BSWPD) to convert a noisy signal into wavelet coefficients (WCs). It is found that the VAD using bark-scale spectral entropy, called as BS-Entropy, parameter is superior to other energy-based approach especially in variable noise-level. The wavelet coefficient threshold (WCT) of each subband is then temporally adjusted according to the result of VAD approach. In a speech-dominated frame, the speech is categorized into either a voiced frame or an unvoiced frame. A voiced frame possesses a strong tone-like spectrum in lower subbands, so that the WCs of lower-band must be reserved. On the contrary, the WCT tends to increase in lower-band if the speech is categorized as unvoiced. In a noise-dominated frame, the background noise can be almost completely removed by increasing the WCT. The objective and subjective experimental results are then used to evaluate the proposed system. The experiments show that this algorithm is valid on various noise conditions, especially for color noise and non-stationary noise conditions.

  15. White noise analysis of pace-maker-response interactions and non-linearities in slowly adapting crayfish stretch receptor.

    PubMed Central

    Buño, W; Bustamante, J; Fuentes, J

    1984-01-01

    Input-output relations were investigated in the slowly adapting stretch receptor organ of crayfish using a Gaussian white noise length input with a 0.03-12.5 Hz band width and the resulting action potential output. The noise input was presented to the de-efferented receptor in situ, at three mean elongations and at four different amplitudes. The three mean elongations were set within the normal range in vivo, two at the extremes close to the minimum and maximum physiological lengths and the other in the mid-range. With white noise inputs there is a finite probability that the system will be tested in all possible conditions within the chosen band width because white noise has the advantage that it contains, with a finite probability, all possible stimulus wave forms at random. The analysis indicated similarities between the effects of the input variables, namely white noise amplitude and mean elongation. With low input variables the activity was periodic. With larger inputs, impulse rates were higher and irregular. The average length trajectories leading to a spike (i.e. the average stimulus) were either biphasic with high inputs or multiphasic and periodic with lower input variables. The frequency of periodicity increased with mean elongation. Although for a given length and noise amplitude a variety of individual length trajectories preceded spikes, the final biphasic shortening-lengthening average stimulus sequence before a spike was similar in all cases irrespective of the input variables. The number of possible trajectories decreased with increments in the input variables. The standard deviation of length values for each average stimulus was computed and displayed as a function of time relative to the spike. It was first constant, and decreased gradually to a minimum value at the spike reference. Standard deviation values were lower for higher white noise amplitudes and mean elongation. Simple, short-lasting stimulus wave forms in the white noise were isolated

  16. Room reverberation effects in hearing aid feedback cancellation.

    PubMed

    Kates, J M

    2001-01-01

    Room reverberation can affect feedback cancellation in hearing aids, with the strength of the effects depending on the acoustical conditions. These effects were studied using a behind the ear (BTE) hearing aid mounted on a dummy head and coupled to the ear canal via an open fitting. The hearing aid impulse response was measured for the dummy head placed at eight closely spaced locations in a typical office. The feedback cancellation in the hearing aid used a set of filter coefficients that were initialized for one location within the room, and then allowed to adapt to the feedback path measured at the same or to a different location. The maximum stable gain for the hearing aid was then estimated without feedback cancellation, for the initial set of feedback cancellation filter coefficients prior to adaptation, and for the feedback cancellation filter after adaptation. A low-order ARMA model combining a fixed set of poles with an adaptive FIR filter is shown to be effective in representing the feedback path exclusive of reverberation. Increasing the adaptive filter length has only a small benefit in improving the feedback cancellation performance due to the inability of the system to model the room reverberation. The mismatch between the modeled and actual feedback paths limits the headroom increase that can be achieved when using feedback cancellation, and varies with the location within the room. PMID:11206165

  17. Speech intelligibility improvements with hearing aids using bilateral and binaural adaptive multichannel Wiener filtering based noise reduction.

    PubMed

    Cornelis, Bram; Moonen, Marc; Wouters, Jan

    2012-06-01

    This paper evaluates noise reduction techniques in bilateral and binaural hearing aids. Adaptive implementations (on a real-time test platform) of the bilateral and binaural speech distortion weighted multichannel Wiener filter (SDW-MWF) and a competing bilateral fixed beamformer are evaluated. As the SDW-MWF relies on a voice activity detector (VAD), a realistic binaural VAD is also included. The test subjects (both normal hearing subjects and hearing aid users) are tested by an adaptive speech reception threshold (SRT) test in different spatial scenarios, including a realistic cafeteria scenario with nonstationary noise. The main conclusions are: (a) The binaural SDW-MWF can further improve the SRT (up to 2 dB) over the improvements achieved by bilateral algorithms, although a significant difference is only achievable if the binaural SDW-MWF uses a perfect VAD. However, in the cafeteria scenario only the binaural SDW-MWF achieves a significant SRT improvement (2.6 dB with perfect VAD, 2.2 dB with real VAD), for the group of hearing aid users. (b) There is no significant degradation when using a real VAD at the input signal-to-noise ratio (SNR) levels where the hearing aid users reach their SRT. (c) The bilateral SDW-MWF achieves no SRT improvements compared to the bilateral fixed beamformer.

  18. Adaptive Noise Suppression of Pediatric Lung Auscultations With Real Applications to Noisy Clinical Settings in Developing Countries

    PubMed Central

    Emmanouilidou, Dimitra; McCollum, Eric D.; Park, Daniel E.

    2015-01-01

    Goal Chest auscultation constitutes a portable low-cost tool widely used for respiratory disease detection. Though it offers a powerful means of pulmonary examination, it remains riddled with a number of issues that limit its diagnostic capability. Particularly, patient agitation (especially in children), background chatter, and other environmental noises often contaminate the auscultation, hence affecting the clarity of the lung sound itself. This paper proposes an automated multiband denoising scheme for improving the quality of auscultation signals against heavy background contaminations. Methods The algorithm works on a simple two-microphone setup, dynamically adapts to the background noise and suppresses contaminations while successfully preserving the lung sound content. The proposed scheme is refined to offset maximal noise suppression against maintaining the integrity of the lung signal, particularly its unknown adventitious components that provide the most informative diagnostic value during lung pathology. Results The algorithm is applied to digital recordings obtained in the field in a busy clinic in West Africa and evaluated using objective signal fidelity measures and perceptual listening tests performed by a panel of licensed physicians. A strong preference of the enhanced sounds is revealed. Significance The strengths and benefits of the proposed method lie in the simple automated setup and its adaptive nature, both fundamental conditions for everyday clinical applicability. It can be simply extended to a real-time implementation, and integrated with lung sound acquisition protocols. PMID:25879837

  19. An adaptive integrated algorithm for noninvasive fetal ECG separation and noise reduction based on ICA-EEMD-WS.

    PubMed

    Liu, Guangchen; Luan, Yihui

    2015-11-01

    High-resolution fetal electrocardiogram (FECG) plays an important role in assisting physicians to detect fetal changes in the womb and to make clinical decisions. However, in real situations, clear FECG is difficult to extract because it is usually overwhelmed by the dominant maternal ECG and other contaminated noise such as baseline wander, high-frequency noise. In this paper, we proposed a novel integrated adaptive algorithm based on independent component analysis (ICA), ensemble empirical mode decomposition (EEMD), and wavelet shrinkage (WS) denoising, denoted as ICA-EEMD-WS, for FECG separation and noise reduction. First, ICA algorithm was used to separate the mixed abdominal ECG signal and to obtain the noisy FECG. Second, the noise in FECG was reduced by a three-step integrated algorithm comprised of EEMD, useful subcomponents statistical inference and WS processing, and partial reconstruction for baseline wander reduction. Finally, we evaluate the proposed algorithm using simulated data sets. The results indicated that the proposed ICA-EEMD-WS outperformed the conventional algorithms in signal denoising. PMID:26429348

  20. Analysis of helicopter blade-vortex interaction noise with application to adaptive-passive and active alleviation methods

    NASA Astrophysics Data System (ADS)

    Tauszig, Lionel Christian

    This study focuses on detection and analysis methods of helicopter blade-vortex interactions (BVI) and applies these methods to two different BVI noise alleviation schemes---an adaptive-passive and an active scheme. A standard free-wake analysis based on relaxation methods is extended in this study to compute high-resolution blade loading, to account for blade-to-blade dissimilarities, and dual vortices when there is negative loading at the blade tips. The free-wake geometry is still calculated on a coarse azimuthal grid and then interpolated to a high-resolution grid to calculate the BVI induced impulsive loading. Blade-to-blade dissimilarities are accounted by allowing the different blades to release their own vortices. A number of BVI detection criteria, including the spherical method (a geometric criterion developed in this thesis) are critically examined. It was determined that high-resolution azimuthal discretization is required in virtually all detection methods except the spherical method which detected the occurrence of parallel BVI even while using a low-resolution azimuthal mesh. Detection methods based on inflow and blade loads were, in addition, found to be sensitive to vortex core size. While most BVI studies use the high-resolution airloads to compute BVI noise, the total noise can often be due to multiple dominant interactions on the advancing and retreating sides. A methodology is developed to evaluate the contribution of an individual interaction to the total BVI noise, based on using the loading due to an individual vortex as an input to the acoustic code WOPWOP. The adaptive-passive BVI alleviation method considered in this study comprises of reducing the length of one set of opposite blades (of a 4-bladed rotor) in low-speed descent. Results showed that differential coning resulting from the blade dissimilarity increases the blade-vortex miss-distances and reduces the BVI noise by 4 dB. The Higher Harmonic Control Aeroacoustic Rotor Test (HART

  1. OCAM2S: an integral shutter ultrafast and low noise wavefront sensor camera for laser guide stars adaptive optics systems

    NASA Astrophysics Data System (ADS)

    Gach, Jean-Luc; Feautrier, Philippe; Balard, Philippe; Guillaume, Christian; Stadler, Eric

    2014-07-01

    To date, the OCAM2 system has demonstrated to be the fastest and lowest noise production ready wavefront sensor, achieving 2067 full frames per second with subelectron readout noise. This makes OCAM2 the ideal system for natural as well as continuous wave laser guide star wavefront sensing. In this paper we present the new gated version of OCAM2 named OCAM2-S, using E2V's CCD219 sensor with integral shutter. This new camera offers the same superb characteristics than OCAM2 both in terms of speed and readout noise but also offers a shutter function that makes the sensor only sensitive to light for very short periods, at will. We will report on gating time and extinction ratio performances of this new camera. This device opens new possibilities for Rayleigh pulsed lasers adaptive optics systems. With a shutter time constant well below 1 microsecond, this camera opens new solutions for pulsed sodium lasers with backscatter suppression or even spot elongation minimization for ELT LGS.

  2. Multi-dimensional complete ensemble empirical mode decomposition with adaptive noise applied to laser speckle contrast images.

    PubMed

    Humeau-Heurtier, Anne; Mahé, Guillaume; Abraham, Pierre

    2015-10-01

    Laser speckle contrast imaging (LSCI) is a noninvasive full-field optical technique which allows analyzing the dynamics of microvascular blood flow. LSCI has attracted attention because it is able to image blood flow in different kinds of tissue with high spatial and temporal resolutions. Additionally, it is simple and necessitates low-cost devices. However, the physiological information that can be extracted directly from the images is not completely determined yet. In this work, a novel multi-dimensional complete ensemble empirical mode decomposition with adaptive noise (MCEEMDAN) is introduced and applied in LSCI data recorded in three physiological conditions (rest, vascular occlusion and post-occlusive reactive hyperaemia). MCEEMDAN relies on the improved complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) and our algorithm is specifically designed to analyze multi-dimensional data (such as images). Over the recent multi-dimensional ensemble empirical mode decomposition (MEEMD), MCEEMDAN has the advantage of leading to an exact reconstruction of the original data. The results show that MCEEMDAN leads to intrinsic mode functions and residue that reveal hidden patterns in LSCI data. Moreover, these patterns differ with physiological states. MCEEMDAN appears as a promising way to extract features in LSCI data for an improvement of the image understanding.

  3. Analytical investigation of adaptive control of radiated inlet noise from turbofan engines

    NASA Technical Reports Server (NTRS)

    Risi, John D.; Burdisso, Ricardo A.

    1994-01-01

    An analytical model has been developed to predict the resulting far field radiation from a turbofan engine inlet. A feedforward control algorithm was simulated to predict the controlled far field radiation from the destructive combination of fan noise and secondary control sources. Numerical results were developed for two system configurations, with the resulting controlled far field radiation patterns showing varying degrees of attenuation and spillover. With one axial station of twelve control sources and error sensors with equal relative angular positions, nearly global attenuation is achieved. Shifting the angular position of one error sensor resulted in an increase of spillover to the extreme sidelines. The complex control inputs for each configuration was investigated to identify the structure of the wave pattern created by the control sources, giving an indication of performance of the system configuration. It is deduced that the locations of the error sensors and the control source configuration are equally critical to the operation of the active noise control system.

  4. Adapting histogram for automatic noise data removal in building interior point cloud data

    NASA Astrophysics Data System (ADS)

    Shukor, S. A. Abdul; Rushforth, E. J.

    2015-05-01

    3D point cloud data is now preferred by researchers to generate 3D models. These models can be used throughout a variety of applications including 3D building interior models. The rise of Building Information Modeling (BIM) for Architectural, Engineering, Construction (AEC) applications has given 3D interior modelling more attention recently. To generate a 3D model representing the building interior, a laser scanner is used to collect the point cloud data. However, this data often comes with noise. This is due to several factors including the surrounding objects, lighting and specifications of the laser scanner. This paper highlights on the usage of the histogram to remove the noise data. Histograms, used in statistics and probability, are regularly being used in a number of applications like image processing, where a histogram can represent the total number of pixels in an image at each intensity level. Here, histograms represent the number of points recorded at range distance intervals in various projections. As unwanted noise data has a sparser cloud density compared to the required data and is usually situated at a notable distance from the required data, noise data will have lower frequencies in the histogram. By defining the acceptable range using the average frequency, points below this range can be removed. This research has shown that these histograms have the capabilities to remove unwanted data from 3D point cloud data representing building interiors automatically. This feature will aid the process of data preprocessing in producing an ideal 3D model from the point cloud data.

  5. Stochastic optimal control and estimation methods adapted to the noise characteristics of the sensorimotor system.

    PubMed

    Todorov, Emanuel

    2005-05-01

    Optimality principles of biological movement are conceptually appealing and straightforward to formulate. Testing them empirically, however, requires the solution to stochastic optimal control and estimation problems for reasonably realistic models of the motor task and the sensorimotor periphery. Recent studies have highlighted the importance of incorporating biologically plausible noise into such models. Here we extend the linear-quadratic-gaussian framework--currently the only framework where such problems can be solved efficiently--to include control-dependent, state-dependent, and internal noise. Under this extended noise model, we derive a coordinate-descent algorithm guaranteed to converge to a feedback control law and a nonadaptive linear estimator optimal with respect to each other. Numerical simulations indicate that convergence is exponential, local minima do not exist, and the restriction to nonadaptive linear estimators has negligible effects in the control problems of interest. The application of the algorithm is illustrated in the context of reaching movements. A Matlab implementation is available at www.cogsci.ucsd.edu/~todorov.

  6. Dual adaptive statistical approach for quantitative noise reduction in photon-counting medical imaging: application to nuclear medicine images

    NASA Astrophysics Data System (ADS)

    Hannequin, Pascal Paul

    2015-06-01

    Noise reduction in photon-counting images remains challenging, especially at low count levels. We have developed an original procedure which associates two complementary filters using a Wiener-derived approach. This approach combines two statistically adaptive filters into a dual-weighted (DW) filter. The first one, a statistically weighted adaptive (SWA) filter, replaces the central pixel of a sliding window with a statistically weighted sum of its neighbors. The second one, a statistical and heuristic noise extraction (extended) (SHINE-Ext) filter, performs a discrete cosine transformation (DCT) using sliding blocks. Each block is reconstructed using its significant components which are selected using tests derived from multiple linear regression (MLR). The two filters are weighted according to Wiener theory. This approach has been validated using a numerical phantom and a real planar Jaszczak phantom. It has also been illustrated using planar bone scintigraphy and myocardial single-photon emission computed tomography (SPECT) data. Performances of filters have been tested using mean normalized absolute error (MNAE) between the filtered images and the reference noiseless or high-count images. Results show that the proposed filters quantitatively decrease the MNAE in the images and then increase the signal-to-noise Ratio (SNR). This allows one to work with lower count images. The SHINE-Ext filter is well suited to high-size images and low-variance areas. DW filtering is efficient for low-size images and in high-variance areas. The relative proportion of eliminated noise generally decreases when count level increases. In practice, SHINE filtering alone is recommended when pixel spacing is less than one-quarter of the effective resolution of the system and/or the size of the objects of interest. It can also be used when the practical interest of high frequencies is low. In any case, DW filtering will be preferable. The proposed filters have been applied to nuclear

  7. Energy Detection Based Estimation of Channel Occupancy Rate with Adaptive Noise Estimation

    NASA Astrophysics Data System (ADS)

    Lehtomäki, Janne J.; Vuohtoniemi, Risto; Umebayashi, Kenta; Mäkelä, Juha-Pekka

    Recently, there has been growing interest in opportunistically utilizing the 2.4GHz ISM-band. Numerous spectrum occupancy measurements covering the ISM-band have been performed to analyze the spectrum usage. However, in these campaigns the verification of the correctness of the obtained occupancy values for the highly dynamic ISM-band has not been presented. In this paper, we propose and verify channel occupancy rate (COR) estimation utilizing energy detection mechanism with a novel adaptive energy detection threshold setting method. The results are compared with the true reference COR values. Several different types of verification measurements showed that our setup can estimate the COR values of 802.11 traffic well, with negligible overestimation. The results from real-time real-life measurements also confirm that the proposed adaptive threshold setting method enables accurate thresholds even in the situations where multiple interferers are present in the received signal.

  8. Seismic random noise elimination according to the adaptive fractal conservation law

    NASA Astrophysics Data System (ADS)

    Meng, Fanlei; Li, Yue; Zeng, Qian

    2016-05-01

    The fractal conservation law (FCL) is based on the Cauchy problem of the partial differential equation (PDE), which is modified by an anti-diffusive term of lower order. The analysis indicates that it can eliminate the high frequencies and preserve or amplify the low/medium frequencies. The performance of FCL depends on the threshold selected for the PDE. This threshold corresponds to the cut-off frequency of FCL in the frequency domain. Generally, the threshold is fixed. Thus, the FCL cannot track the signal beyond the cut-off frequency, and it removes the higher-frequency components of the signal. To solve this problem, an adaptive FCL filtering method is presented. The main purpose of this method is to select the optimal FCL threshold in each sample index such that it can adaptively track the rapid changes in the signal. In the adaptive FCL, we select FCL estimations with different thresholds and construct a convex hull of these estimations of each sample index. Consequently, we introduce a quadratic functional with respect to FCL estimation to ensure that we select the optimal estimation from the convex hull of each sample index. This leads to a box-constrained convex problem, which can be solved by the Viterbi algorithm.

  9. Linear adaptive noise-reduction filters for tomographic imaging: Optimizing for minimum mean square error

    SciTech Connect

    Sun, W Y

    1993-04-01

    This thesis solves the problem of finding the optimal linear noise-reduction filter for linear tomographic image reconstruction. The optimization is data dependent and results in minimizing the mean-square error of the reconstructed image. The error is defined as the difference between the result and the best possible reconstruction. Applications for the optimal filter include reconstructions of positron emission tomographic (PET), X-ray computed tomographic, single-photon emission tomographic, and nuclear magnetic resonance imaging. Using high resolution PET as an example, the optimal filter is derived and presented for the convolution backprojection, Moore-Penrose pseudoinverse, and the natural-pixel basis set reconstruction methods. Simulations and experimental results are presented for the convolution backprojection method.

  10. Speech enhancement using parametric spectral subtraction combined with generalized sidelobe canceller

    NASA Astrophysics Data System (ADS)

    Cho, Jaeyoun; Krishnamurthy, Ashok

    2003-10-01

    Speech enhancement is an important problem with applications in hearing aid design, speech recognition, speech coding, etc. Parametric spectral subtraction is a common method for speech enhancement when only a single channel of data is available. On the other hand, beamforming methods can be used when multiple channels of spatially separated data are available, such as from a microphone array. In previous work, we have shown that spectral subtraction combined with spatial averaging from multiple microphones leads to improvements in speech SNR and reduction of musical noise compared with either method used alone. In this talk, we extend the previous work to combine parametric spectral subtraction with adaptive beamforming, specifically the generalized sidelobe canceller. The proposed parametric spectral subtraction method determines the parameters adaptively so as to minimize speech distortion. In addition, it is shown that the major drawback of spectral subtraction, so-called musical noise, can be diminished by adaptive beamforming process. We show that the method leads to a reduction of musical noise and results in the enhanced speech having better quality and intelligibility.

  11. Design, Fabrication, and Testing of SMA Enabled Adaptive Chevrons for Jet Noise Reduction

    NASA Technical Reports Server (NTRS)

    Turner, Travis L.; Buehrle, Ralph D.; Cano, Roberto J.; Fleming, Gary A.

    2004-01-01

    This study presents the status and results from an effort to design, fabricate, and test an adaptive jet engine chevron concept based upon embedding shape memory alloy (SMA) actuators in a composite laminate, termed a SMA hybrid composite (SMAHC). The approach for fabricating the adaptive SMAHC chevrons involves embedding prestrained Nitinol actuators on one side of the mid-plane of the composite laminate such that thermal excitation generates a thermal moment and deflects the structure. A glass-epoxy pre-preg/Nitinol ribbon material system and a vacuum hot press consolidation approach are employed. A versatile test system for control and measurement of the chevron deflection performance is described. Projection moire interferometry (PMI) is used for global deformation measurement and infrared (IR) thermography is used for 2-D temperature measurement and feedback control. A recently commercialized constitutive model for SMA and SMAHC materials is used in the finite element code ABAQUS to perform nonlinear static analysis of the chevron prototypes. Excellent agreement is achieved between the predicted and measured chevron deflection performance, thereby validating the design tool. Although the performance results presented in this paper fall short of the requirement, the concept is proven and an approach for achieving the performance objectives is evident.

  12. Postal cancellation from spaceport

    NASA Astrophysics Data System (ADS)

    The John F. Kennedy Space Center, in cooperation with the United States Postal Service, is offering a cancellation service to interested philatelists for the space flight programs at Kennedy.Philatelists who wish to avail themselves of this service may do so by following the procedures outlined below: Specify the event for which you wish this service. There is a limit of five covers per customer per event.

  13. Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Opportunitistic Enzymes, Catalytic Promiscuity and the Evolution of chemodiversity in Nature (2010 JGI User Meeting)

    ScienceCinema

    Noel, Joseph

    2016-07-12

    Joseph Noel from the Salk Institute on "Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Enzymes, Catalytic Promiscuity and the Evolution of Chemodiversity in Nature" on March 26, 2010 at the 5th Annual DOE JGI User Meeting

  14. Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Opportunitistic Enzymes, Catalytic Promiscuity and the Evolution of chemodiversity in Nature (2010 JGI User Meeting)

    SciTech Connect

    Noel, Joseph

    2010-03-26

    Joseph Noel from the Salk Institute on "Metabolic Noise, Vestigial Metabolites or the Raw Material of Ecological Adaptation? Enzymes, Catalytic Promiscuity and the Evolution of Chemodiversity in Nature" on March 26, 2010 at the 5th Annual DOE JGI User Meeting

  15. Active attenuation of propeller blade passage noise

    NASA Technical Reports Server (NTRS)

    Zalas, J. M.; Tichy, J.

    1984-01-01

    Acoustic measurements are presented to show that active cancellation can be used to achieve significant reduction of blade passage noise in a turboprop cabin. Simultaneous suppression of all blade passage frequencies was attained. The spatial volume over which cancellation occurred, however, is limited. Acoustic intensity maps are presented to show that the acoustic input to the fuselage was sufficiently non-localized so as to require more judicious selection of cancellation speaker location.

  16. Active{sup 3} noise reduction

    SciTech Connect

    Holzfuss, J.

    1996-06-01

    Noise reduction is a problem being encountered in a variety of applications, such as environmental noise cancellation, signal recovery and separation. Passive noise reduction is done with the help of absorbers. Active noise reduction includes the transmission of phase inverted signals for the cancellation. This paper is about a threefold active approach to noise reduction. It includes the separation of a combined source, which consists of both a noise and a signal part. With the help of interaction with the source by scanning it and recording its response, modeling as a nonlinear dynamical system is achieved. The analysis includes phase space analysis and global radial basis functions as tools for the prediction used in a subsequent cancellation procedure. Examples are given which include noise reduction of speech. {copyright} {ital 1996 American Institute of Physics.}

  17. Improving misalignment for feedback path estimation in hearing aid by multiple short-time noise injections.

    PubMed

    Khoubrouy, Soudeh A; Panahi, Issa M S

    2012-01-01

    Adaptive Feedback Cancellation (AFC) methods are used to find an FIR filter to cancel the negative effect of acoustic feedback between the loudspeaker and microphone of the hearing aid. Finding the AFC filter of appropriate order/length directly affects the performance and complexity of the system. In this paper, we use noise injection method to find the AFC filter estimating the feedback path model. We show that the optimum length which guarantees a good compromise between the quality and the complexity of the system may be smaller than the length of the actual feedback path model. However, in order to improve the performance of the system in terms of Misalignment criterion, we propose using multiple short-time noise injections and averaging method to find the best filter estimate of appropriate length. PMID:23367108

  18. A method of interference cancellation in binary PSK coherent receiver

    NASA Astrophysics Data System (ADS)

    Segawa, K.; Nakagawa, M.

    1985-08-01

    A new interference cancellation method using a Costas loop is proposed for PSK communication. Experiments are reported which demonstrate the influence of the waveform distortion due to a phase shifter on the demodulated data signal, the influence of additive noise on the canceller, and the influence of interference-induced phase jitter on the Costas loop. It is demonstrated that, with the introduction of a simple additional circuit, sufficiently effective interference elimination can be achieved for delta f higher than 0.3 fB, where delta f is the difference between the frequencies of the PSK carrier and the interfering signal and fB is the data bit rate.

  19. 43 CFR 3601.62 - Cancellation procedure.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Disposal; General Provisions Contract and Permit Cancellation § 3601.62 Cancellation procedure....

  20. 43 CFR 3601.62 - Cancellation procedure.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Disposal; General Provisions Contract and Permit Cancellation § 3601.62 Cancellation procedure....

  1. Influence of static and combined magnetic fields' noises on the adaptation of the gravitropic reaction of the cress and maize roots.

    NASA Astrophysics Data System (ADS)

    Bogatina, Nina; Sheykina, Nadiia

    Dependencies of gravitropic reactions in the static magnetic field and at different frequencies of alternative component of the combined magnetic fields were investigated. These frequencies were equal to the cyclotron frequencies of Са2+, Mg2+ ions and ions of auxin and abscisic acid. It was shown that the increasing of magnetic field noise assisted both to the observation of biological effects and to the acceleration of adaptation processes.

  2. [Research on an adaptive fetal electrocardiograph based on DSP].

    PubMed

    Li, Zhi; Shen, Hancong; Mo, Wei

    2008-04-01

    This paper introduces the research and realization of an adaptive fetal electrocardiograph (FECG). We have developed an embedded system which takes the digital signal processor chip TMS320LF2407A as the core. According to the principle of adaptive noise cancelling(ANC), the ANC software algorithm is studied and realized to extract the FECG by non-invasive means, then the embedded system sends the data to the computer through the communication interface for real-time display, analysis and recording of the processing results. The experiments indicate that the design is reasonable and the instrument owns a good performance.

  3. Experimental evaluation of leaky least-mean-square algorithms for active noise reduction in communication headsets

    NASA Astrophysics Data System (ADS)

    Cartes, David A.; Ray, Laura R.; Collier, Robert D.

    2002-04-01

    An adaptive leaky normalized least-mean-square (NLMS) algorithm has been developed to optimize stability and performance of active noise cancellation systems. The research addresses LMS filter performance issues related to insufficient excitation, nonstationary noise fields, and time-varying signal-to-noise ratio. The adaptive leaky NLMS algorithm is based on a Lyapunov tuning approach in which three candidate algorithms, each of which is a function of the instantaneous measured reference input, measurement noise variance, and filter length, are shown to provide varying degrees of tradeoff between stability and noise reduction performance. Each algorithm is evaluated experimentally for reduction of low frequency noise in communication headsets, and stability and noise reduction performance are compared with that of traditional NLMS and fixed-leakage NLMS algorithms. Acoustic measurements are made in a specially designed acoustic test cell which is based on the original work of Ryan et al. [``Enclosure for low frequency assessment of active noise reducing circumaural headsets and hearing protection,'' Can. Acoust. 21, 19-20 (1993)] and which provides a highly controlled and uniform acoustic environment. The stability and performance of the active noise reduction system, including a prototype communication headset, are investigated for a variety of noise sources ranging from stationary tonal noise to highly nonstationary measured F-16 aircraft noise over a 20 dB dynamic range. Results demonstrate significant improvements in stability of Lyapunov-tuned LMS algorithms over traditional leaky or nonleaky normalized algorithms, while providing noise reduction performance equivalent to that of the NLMS algorithm for idealized noise fields.

  4. Reward Improves Cancellation and Restraint Inhibition across Childhood and Adolescence

    ERIC Educational Resources Information Center

    Sinopoli, Katia J.; Schachar, Russell; Dennis, Maureen

    2011-01-01

    Inhibitory control allows for the regulation of thought and action and interacts with motivational variables, such as reward, to modify behavior adaptively as environments change. The authors examined the effects of reward on two distinct forms of inhibitory control, cancellation and restraint. Typically developing children and adolescents…

  5. Alien Crosstalk Cancellation for Multipair Digital Subscriber Line Systems

    NASA Astrophysics Data System (ADS)

    Ginis, George; Peng, Chia-Ning

    2006-12-01

    An overview of alien crosstalk cancellation for DSL systems with multiple pairs is here presented. It is shown that when a common crosstalk source affects the receivers of multiple pairs, the noise exhibits a certain correlation among the pairs. In a DMT system, the frequency-domain noise samples are most strongly correlated between pairs when they correspond to the same tone. Thus, noise decorrelation algorithms applied independently for each tone can provide significant performance enhancements. Three possible methods are described for noise decorrelation, one is suitable for two-sided coordination and two are suited for receiver coordination among the pairs. It is theoretically proven that the data-rate performance of these three methods is identical from the perspective of the sum rate over all pairs. Simulation results corresponding to an ADSL2+ two-pair system with a T1 disturber are presented to illustrate the noise correlation property and to indicate the potential performance benefits.

  6. Unexpected cancellations in gravity theories

    SciTech Connect

    Bern, Z.; Carrasco, J. J.; Johansson, H.; Forde, D.; Ita, H.

    2008-01-15

    Recent computations of scattering amplitudes show that N=8 supergravity is surprisingly well behaved in the ultraviolet and may even be ultraviolet finite in perturbation theory. The novel cancellations necessary for ultraviolet finiteness first appear at one loop in the guise of the ''no-triangle hypothesis.'' We study one-loop amplitudes in pure Einstein gravity and point out the existence of cancellations similar to those found previously in N=8 supergravity. These cancellations go beyond those found in the one-loop effective action. Using unitarity, this suggests that generic theories of quantum gravity based on the Einstein-Hilbert action may be better behaved in the ultraviolet at higher loops than suggested by naive power counting, though without additional (supersymmetric) cancellations they diverge. We comment on future studies that should be performed to support this proposal.

  7. Unexpected Cancellations in Gravity Theories

    SciTech Connect

    Bern, Z.; Carrasco, J.J.; Forde, D.; Ita, H.; Johansson, H.; /UCLA

    2007-07-13

    Recent computations of scattering amplitudes show that N = 8 supergravity is surprisingly well behaved in the ultraviolet and may even be ultraviolet finite in perturbation theory. The novel cancellations necessary for ultraviolet finiteness first appear at one loop in the guise of the ''no-triangle hypothesis''. We study one-loop amplitudes in pure Einstein gravity and point out the existence of cancellations similar to those found previously in N = 8 supergravity. These cancellations go beyond those found in the one-loop effective action. Using unitarity, this suggests that generic theories of quantum gravity based on the Einstein-Hilbert action may be better behaved in the ultraviolet at higher loops than suggested by naive power counting, though without additional (supersymmetric) cancellations they diverge. We comment on future studies that should be performed to support this proposal.

  8. Three-dimensional microarchitecture of adolescent cancellous bone.

    PubMed

    Ding, Ming; Danielsen, Carl Christian; Hvid, Ivan; Overgaard, Søren

    2012-11-01

    This study investigated microarchitectural, mechanical, collagen and mineral properties of normal adolescent cancellous bone, and compared them with adult and aging cancellous bone, to obtain more insight into the subchondral bone adaptations during development and growth. Twenty-three human proximal tibiae were harvested and divided into 3 groups according to their ages: adolescence (9 to 17 years, n=6), young adult (18 to 24 years, n=9), and adult (25 to 30 years, n=8). Twelve cubic cancellous bone samples with dimensions of 8×8×8 mm(3) were produced from each tibia, 6 from each medial and lateral condyle. These samples were micro-CT scanned (vivaCT 40, Scanco Medical AG, Switzerland) resulting in cubic voxel sizes of 10.5*10.5*10.5 μm(3). Microarchitectural properties were calculated. The samples were then tested in compression followed by collagen and mineral determination. Interestingly, the adolescent cancellous bone had similar bone volume fraction (BV/TV), structure type (plate, rod or mixtures), and connectivity (3-D trabecular networks) as the adult cancellous bone. The adolescent cancellous bone had significantly lower bone surface density (bone surface per total volume of specimen) but higher collagen concentration (collagen weight per dry weight of specimen) than the adult cancellous bone; and significant greater trabecular separation (mean distance between trabeculae), significant lower trabecular number (number of trabeculae per volume), tissue density (dry weight per volume of bone matrix excluding marrow space) and mineral concentration (ash weight per dry weight of specimen) than the young adult and adult cancellous bones. Despite these differences, ultimate stress and failure energy were not significantly different among the three groups, only the Young's modulus in anterior-posterior direction was significantly lower in adolescence. Apparent density appears to be the single best predictor of mechanical properties. In conclusion, adolescent

  9. Hybrid Fluid-borne Noise Control in Fluid-filled Pipelines

    NASA Astrophysics Data System (ADS)

    Pan, M.; Johnston, N.; Plummer, A.

    2016-09-01

    This article reports on an initial investigation of a hybrid fluid-borne noise control system in hydraulic pipelines. The hybrid system is built by integrating an active feedforward noise controller with passive tuned flexible hoses. The active attenuator is designed to cancel the dominant harmonic pressure pulsations in the fluid line, while the passive hose is tuned to attenuate the residual high frequency pulsations. The active attenuator can effectively decrease the fluid-borne noise by superimposing a secondary anti-phase control signal. Adaptive notch filters with the filtered-X least mean square algorithm were applied for the controller and a frequency-domain least mean square filter was used for the secondary path on-line identification. The transmission line model was used to model the pipeline, and a time-domain hose model which includes coupling of longitudinal wall and fluid waves was used to model the flexible hose. Simulation results show that very good noise cancellation was achieved using the proposed approach, which has several advantages over existing fluid-borne noise control systems, being effective for a wide range of frequencies without impairing the system dynamic response much. While the flexible hoses may be less effective than purpose-built passive silencers, they can form an inexpensive and practical solution in combination with active control.

  10. Active local volume displacement cancellation of a vibrating baffled beam

    NASA Astrophysics Data System (ADS)

    Zahui, Marcellin

    An active noise control apparatus is developed. The device reduces the sound radiated from a vibrating clamped beam. The attenuation of the sound field is obtained through minimization of local volume displacements of the vibrating beam. Two single- input/single-output cancellation devices are used. Each device employs a motion sensor and an acoustic actuator. The actuator is a loudspeaker equipped with a pressure sensor to detect its volume displacement. The motion sensor signal is related to the local volume displacement of the structure which is then reduced by a loudspeaker driven with an equal but opposing volume displacement. The volume displacement sensors are developed and fabricated using Polyvinylidene Fluoride (PVDF). They measure the local volume displacements of the vibrating beam. The pressure sensor is mounted in the loudspeaker enclosure. It provides the feedback signal for the loudspeaker volume displacement control. Previous work showed the successful implementation of this technique for uniformly vibrating radiators. This thesis presents the development of this technique for the reduction of sound radiated from a vibrating beam. First, a numerical local volume displacement cancellation experiment is performed using several loudspeakers, each canceling the volume displacement of a section of the beam. The finite element method is used to calculate the velocity distribution of the vibrating beam. A discretized form of the Rayleigh integral is then used to find the sound pressure and the sound power radiated before and after cancellation. Second, the numerical results are verified by laboratory experiments using a beam divided into two sections. Two motion sensors for the beam and one pressure sensor for each loudspeaker are fabricated and thoroughly checked. The cancellation experiment is then performed on a broadband random noise using two independent Proportional-Derivative (PD) controllers.

  11. A near-threshold, 0.16 nJ/b OOK-transmitter with 0.18 nJ/b noise-cancelling super-regenerative receiver for the medical implant communications service.

    PubMed

    Ma, Chao; Hu, Changhui; Cheng, Jiao; Xia, Lingli; Chiang, Patrick Yin

    2013-12-01

    A 0.16 nJ/b MICS transmitter and 0.18 nJ/b super-regenerative receiver are demonstrated, where each is specifically designed to operate in the near-threshold region. The low-VDD transmitter utilizes a sub-harmonic injection-locked ring oscillator, edge combiner for frequency multiplication, and class-C power amplifier. The low-VDD receiver introduces a replica super-regenerative receiver as a method to reject common-mode noise sources, such as supply/substrate coupling, thereby reducing undesired self-oscillations and improving BER. Designed in a 90-nm CMOS process, the test-chip measurements show a sensitivity of -80 dBm at 500 kb/s and -65 dBm at 1 Mb/s, respectively, at a BER less than 10⁻³, with 340 μW total power.

  12. Transversely isotropic elasticity imaging of cancellous bone.

    PubMed

    Shore, Spencer W; Barbone, Paul E; Oberai, Assad A; Morgan, Elise F

    2011-06-01

    , the effects of noise on reconstruction quality is demonstrated and a signal-to-noise ratio (SNR) of 40 dB is identified as a reasonable threshold for obtaining accurate reconstructions from experimental data. This study demonstrates that given an appropriate set of displacement fields, level of regularization, and signal strength, the transversely isotropic method can recover the relative magnitudes of all five elastic parameters without an independent measurement of stress. The quality of the reconstructions improves with increasing contrast, magnitude of deformation, and asymmetry in the distributions of material properties, indicating that elasticity imaging of cancellous bone could be a useful tool in laboratory studies to monitor the progression of damage and disease in this tissue. PMID:21744922

  13. Towards undistorted and noise-free speech in an MRI scanner: correlation subtraction followed by spectral noise gating.

    PubMed

    Inouye, Joshua M; Blemker, Silvia S; Inouye, David I

    2014-03-01

    Noise cancellation in an MRI environment is difficult due to the high noise levels that are in the spectral range of human speech. This paper describes a two-step method to cancel MRI noise that combines operations in both the time domain (correlation subtraction) and the frequency domain (spectral noise gating). The resulting filtered recording has a noise power suppression of over 100 dB, a significant improvement over previously described techniques on MRI noise cancellation. The distortion is lower and the noise suppression higher than using spectral noise gating in isolation. Implementation of this method will aid in detailed studies of speech in relation to vocal tract and velopharyngeal function.

  14. Adapt

    NASA Astrophysics Data System (ADS)

    Bargatze, L. F.

    2015-12-01

    Active Data Archive Product Tracking (ADAPT) is a collection of software routines that permits one to generate XML metadata files to describe and register data products in support of the NASA Heliophysics Virtual Observatory VxO effort. ADAPT is also a philosophy. The ADAPT concept is to use any and all available metadata associated with scientific data to produce XML metadata descriptions in a consistent, uniform, and organized fashion to provide blanket access to the full complement of data stored on a targeted data server. In this poster, we present an application of ADAPT to describe all of the data products that are stored by using the Common Data File (CDF) format served out by the CDAWEB and SPDF data servers hosted at the NASA Goddard Space Flight Center. These data servers are the primary repositories for NASA Heliophysics data. For this purpose, the ADAPT routines have been used to generate data resource descriptions by using an XML schema named Space Physics Archive, Search, and Extract (SPASE). SPASE is the designated standard for documenting Heliophysics data products, as adopted by the Heliophysics Data and Model Consortium. The set of SPASE XML resource descriptions produced by ADAPT includes high-level descriptions of numerical data products, display data products, or catalogs and also includes low-level "Granule" descriptions. A SPASE Granule is effectively a universal access metadata resource; a Granule associates an individual data file (e.g. a CDF file) with a "parent" high-level data resource description, assigns a resource identifier to the file, and lists the corresponding assess URL(s). The CDAWEB and SPDF file systems were queried to provide the input required by the ADAPT software to create an initial set of SPASE metadata resource descriptions. Then, the CDAWEB and SPDF data repositories were queried subsequently on a nightly basis and the CDF file lists were checked for any changes such as the occurrence of new, modified, or deleted

  15. Split SR-RLS for the Joint Initialization of the Per-Tone Equalizers and Per-Tone Echo Cancelers in DMT-Based Receivers

    NASA Astrophysics Data System (ADS)

    Ysebaert, Geert; Vanbleu, Koen; Cuypers, Gert; Moonen, Marc

    2004-12-01

    In asymmetric digital subscriber lines (ADSL), the available bandwidth is divided in subcarriers or tones which are assigned to the upstream and/or downstream transmission direction. To allow efficient bidirectional communication over one twisted pair, echo cancellation is required to separate upstream and downstream channels. In addition, intersymbol interference and intercarrier interference have to be reduced by means of equalization. In this paper, a computationally efficient algorithm for adaptively initializing the per-tone equalizers (PTEQ) and per-tone echo cancelers (PTEC) is presented. For a given number of equalizer and echo canceler taps per-tone, it was shown that the joint PTEQ/PTEC receiver structure is able to maximize the signal-to-noise ratio (SNR) on each subcarrier and hence also the achievable bit rate. The proposed initialization scheme is based on a modification of the square root recursive least squares (SR-RLS) algorithm to reduce computational complexity and memory requirement compared to full SR-RLS, while keeping the convergence rate acceptably fast. Our performance analysis will show that the proposed method converges in the mean and an upper bound for the step size is given. Moreover, we will indicate how the presented initialization method can be reused in several other ADSL applications.

  16. 34 CFR 674.52 - Cancellation procedures.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... accelerated— (i) May qualify for a loan cancellation for services performed before the date of acceleration; and (ii) Cannot qualify for a cancellation for services performed on or after the date of...

  17. Long-term, passive exposure to non-traumatic acoustic noise induces neural adaptation in the adult rat medial geniculate body and auditory cortex.

    PubMed

    Lau, Condon; Zhang, Jevin W; McPherson, Bradley; Pienkowski, Martin; Wu, Ed X

    2015-02-15

    Exposure to loud sounds can lead to permanent hearing loss, i.e., the elevation of hearing thresholds. Exposure at more moderate sound pressure levels (SPLs) (non-traumatic and within occupational limits) may not elevate thresholds, but could in the long-term be detrimental to speech intelligibility by altering its spectrotemporal representation in the central auditory system. In support of this, electrophysiological and behavioral changes following long-term, passive (no conditioned learning) exposure at moderate SPLs have recently been observed in adult animals. To assess the potential effects of moderately loud noise on the entire auditory brain, we employed functional magnetic resonance imaging (fMRI) to study noise-exposed adult rats. We find that passive, pulsed broadband noise exposure for two months at 65 dB SPL leads to a decrease of the sound-evoked blood oxygenation level-dependent fMRI signal in the thalamic medial geniculate body (MGB) and in the auditory cortex (AC). This points to the thalamo-cortex as the site of the neural adaptation to the moderately noisy environment. The signal reduction is statistically significant during 10 Hz pulsed acoustic stimulation (MGB: p<0.05, AC: p<10(-4)), but not during 5 Hz stimulation. This indicates that noise exposure has a greater effect on the processing of higher pulse rate sounds. This study has enhanced our understanding of functional changes following exposure by mapping changes across the entire auditory brain. These findings have important implications for speech processing, which depends on accurate processing of sounds with a wide spectrum of pulse rates.

  18. 77 FR 19747 - Proposed Cancelation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-02

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Office of the Secretary Proposed Cancelation of the Air Taxi Authority Of VIH Cougar Helicopters, Inc... cause why it should not issue an order finding that VIH Cougar Helicopters, Inc. is not a U.S....

  19. 47 CFR 213.3 - Cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 5 2011-10-01 2011-10-01 false Cancellation. 213.3 Section 213.3 Telecommunication OFFICE OF SCIENCE AND TECHNOLOGY POLICY AND NATIONAL SECURITY COUNCIL GOVERNMENT AND PUBLIC CORRESPONDENCE TELECOMMUNICATIONS PRECEDENCE SYSTEM § 213.3 Cancellation. This circular cancels: (a)...

  20. 47 CFR 213.3 - Cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Cancellation. 213.3 Section 213.3 Telecommunication OFFICE OF SCIENCE AND TECHNOLOGY POLICY AND NATIONAL SECURITY COUNCIL GOVERNMENT AND PUBLIC CORRESPONDENCE TELECOMMUNICATIONS PRECEDENCE SYSTEM § 213.3 Cancellation. This circular cancels: (a)...

  1. 47 CFR 213.3 - Cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 5 2013-10-01 2013-10-01 false Cancellation. 213.3 Section 213.3 Telecommunication OFFICE OF SCIENCE AND TECHNOLOGY POLICY AND NATIONAL SECURITY COUNCIL GOVERNMENT AND PUBLIC CORRESPONDENCE TELECOMMUNICATIONS PRECEDENCE SYSTEM § 213.3 Cancellation. This circular cancels: (a)...

  2. 47 CFR 213.3 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 5 2014-10-01 2014-10-01 false Cancellation. 213.3 Section 213.3 Telecommunication OFFICE OF SCIENCE AND TECHNOLOGY POLICY AND NATIONAL SECURITY COUNCIL GOVERNMENT AND PUBLIC CORRESPONDENCE TELECOMMUNICATIONS PRECEDENCE SYSTEM § 213.3 Cancellation. This circular cancels: (a)...

  3. Enhanced Cancelable Biometrics for Online Signature Verification

    NASA Astrophysics Data System (ADS)

    Muramatsu, Daigo; Inuma, Manabu; Shikata, Junji; Otsuka, Akira

    Cancelable approaches for biometric person authentication have been studied to protect enrolled biometric data, and several algorithms have been proposed. One drawback of cancelable approaches is that the performance is inferior to that of non-cancelable approaches. In this paper, we propose a scheme to improve the performance of a cancelable approach for online signature verification. Our scheme generates two cancelable dataset from one raw dataset and uses them for verification. Preliminary experiments were performed using a distance-based online signature verification algorithm. The experimental results show that our proposed scheme is promising.

  4. REGULAR VERSUS DIFFUSIVE PHOTOSPHERIC FLUX CANCELLATION

    SciTech Connect

    Litvinenko, Yuri E.

    2011-04-20

    Observations of photospheric flux cancellation on the Sun imply that cancellation can be a diffusive rather than regular process. A criterion is derived, which quantifies the parameter range in which diffusive photospheric cancellation should occur. Numerical estimates show that regular cancellation models should be expected to give a quantitatively accurate description of photospheric cancellation. The estimates rely on a recently suggested scaling for a turbulent magnetic diffusivity, which is consistent with the diffusivity measurements on spatial scales varying by almost two orders of magnitude. Application of the turbulent diffusivity to large-scale dispersal of the photospheric magnetic flux is discussed.

  5. Multi-band locally-adaptive contrast enhancement algorithm with built-in noise and artifact suppression mechanisms

    NASA Astrophysics Data System (ADS)

    Cvetkovic, Sascha D.; Schirris, Johan; de With, Peter H. N.

    2008-01-01

    For real-time imaging in surveillance applications, visibility of details is of primary importance to ensure customer confidence. Usually, image quality is improved by enhancing contrast and sharpness. Many complex scenes require local contrast improvements that should bring details to the best possible visibility. However, local enhancement methods mainly suffer from ringing artifacts and noise over-enhancement. In this paper, we present a new multi-window real-time high-frequency enhancement scheme, in which gain is a non-linear function of the detail energy. Our algorithm simultaneously controls perceived sharpness, ringing artifacts (contrast) and noise, resulting in a good balance between visibility of details and non-disturbance of artifacts. The overall quality enhancement is based on a careful selection of the filter types for the multi-band decomposition and a detailed analysis of the signal per frequency band. The advantage of the proposed technique is that detail gains can be set much higher than usual and the algorithm will reduce them only at places where it is really needed.

  6. Development of adaptive noise reduction filter algorithm for pediatric body images in a multi-detector CT

    NASA Astrophysics Data System (ADS)

    Nishimaru, Eiji; Ichikawa, Katsuhiro; Okita, Izumi; Ninomiya, Yuuji; Tomoshige, Yukihiro; Kurokawa, Takehiro; Ono, Yutaka; Nakamura, Yuko; Suzuki, Masayuki

    2008-03-01

    Recently, several kinds of post-processing image filters which reduce the noise of computed tomography (CT) images have been proposed. However, these image filters are mostly for adults. Because these are not very effective in small (< 20 cm) display fields of view (FOV), we cannot use them for pediatric body images (e.g., premature babies and infant children). We have developed a new noise reduction filter algorithm for pediatric body CT images. This algorithm is based on a 3D post-processing in which the output pixel values are calculated by nonlinear interpolation in z-directions on original volumetric-data-sets. This algorithm does not need the in-plane (axial plane) processing, so the spatial resolution does not change. From the phantom studies, our algorithm could reduce SD up to 40% without affecting the spatial resolution of x-y plane and z-axis, and improved the CNR up to 30%. This newly developed filter algorithm will be useful for the diagnosis and radiation dose reduction of the pediatric body CT images.

  7. Adaptive scene-based correction algorithm for removal of residual fixed pattern noise in microgrid image data

    NASA Astrophysics Data System (ADS)

    Ratliff, Bradley M.; LeMaster, Daniel A.

    2012-06-01

    Pixel-to-pixel response nonuniformity is a common problem that affects nearly all focal plane array sensors. This results in a frame-to-frame fixed pattern noise (FPN) that causes an overall degradation in collected data. FPN is often compensated for through the use of blackbody calibration procedures; however, FPN is a particularly challenging problem because the detector responsivities drift relative to one another in time, requiring that the sensor be recalibrated periodically. The calibration process is obstructive to sensor operation and is therefore only performed at discrete intervals in time. Thus, any drift that occurs between calibrations (along with error in the calibration sources themselves) causes varying levels of residual calibration error to be present in the data at all times. Polarimetric microgrid sensors are particularly sensitive to FPN due to the spatial differencing involved in estimating the Stokes vector images. While many techniques exist in the literature to estimate FPN for conventional video sensors, few have been proposed to address the problem in microgrid imaging sensors. Here we present a scene-based nonuniformity correction technique for microgrid sensors that is able to reduce residual fixed pattern noise while preserving radiometry under a wide range of conditions. The algorithm requires a low number of temporal data samples to estimate the spatial nonuniformity and is computationally efficient. We demonstrate the algorithm's performance using real data from the AFRL PIRATE and University of Arizona LWIR microgrid sensors.

  8. Recent advances in active noise control

    NASA Astrophysics Data System (ADS)

    Guicking, D.

    Advances in the field of active noise control over the last few years are reviewed. Some commercially available products and their technical applications are described, with particular attention given to broadband duct noise silencers, broadband active headphones, waveform synthesis, and LMS controllers. Recent theoretical and experimental research activities are then reviewed. These activities are concerned with duct noise, structural sound, interior spaces, algorithms, echo cancellation, and miscellaneous applications.

  9. Powerline interference reduction in ECG signals using empirical wavelet transform and adaptive filtering.

    PubMed

    Singh, Omkar; Sunkaria, Ramesh Kumar

    2015-01-01

    Separating an information-bearing signal from the background noise is a general problem in signal processing. In a clinical environment during acquisition of an electrocardiogram (ECG) signal, The ECG signal is corrupted by various noise sources such as powerline interference (PLI), baseline wander and muscle artifacts. This paper presents novel methods for reduction of powerline interference in ECG signals using empirical wavelet transform (EWT) and adaptive filtering. The proposed methods are compared with the empirical mode decomposition (EMD) based PLI cancellation methods. A total of six methods for PLI reduction based on EMD and EWT are analysed and their results are presented in this paper. The EWT-based de-noising methods have less computational complexity and are more efficient as compared with the EMD-based de-noising methods. PMID:25412942

  10. Suppression Measured from Chinchilla Auditory-Nerve-Fiber Responses Following Noise-Induced Hearing Loss: Adaptive-Tracking and Systems-Identification Approaches

    PubMed Central

    Sayles, Mark; Walls, Michael K.

    2016-01-01

    The compressive nonlinearity of cochlear signal transduction, reflecting outer-hair-cell function, manifests as suppressive spectral interactions; e.g., two-tone suppression. Moreover, for broadband sounds, there are multiple interactions between frequency components. These frequency-dependent nonlinearities are important for neural coding of complex sounds, such as speech. Acoustic-trauma-induced outer-hair-cell damage is associated with loss of nonlinearity, which auditory prostheses attempt to restore with, e.g., “multi-channel dynamic compression” algorithms. Neurophysiological data on suppression in hearing-impaired (HI) mammals are limited. We present data on firing-rate suppression measured in auditory-nerve-fiber responses in a chinchilla model of noise-induced hearing loss, and in normal-hearing (NH) controls at equal sensation level. Hearing-impaired (HI) animals had elevated single-fiber excitatory thresholds (by ~ 20–40 dB), broadened frequency tuning, and reduced-magnitude distortion-product otoacoustic emissions; consistent with mixed inner- and outer-hair-cell pathology. We characterized suppression using two approaches: adaptive tracking of two-tone-suppression threshold (62 NH, and 35 HI fibers), and Wiener-kernel analyses of responses to broadband noise (91 NH, and 148 HI fibers). Suppression-threshold tuning curves showed sensitive low-side suppression for NH and HI animals. High-side suppression thresholds were elevated in HI animals, to the same extent as excitatory thresholds. We factored second-order Wiener-kernels into excitatory and suppressive sub-kernels to quantify the relative strength of suppression. We found a small decrease in suppression in HI fibers, which correlated with broadened tuning. These data will help guide novel amplification strategies, particularly for complex listening situations (e.g., speech in noise), in which current hearing aids struggle to restore intelligibility. PMID:27080669

  11. Suppression Measured from Chinchilla Auditory-Nerve-Fiber Responses Following Noise-Induced Hearing Loss: Adaptive-Tracking and Systems-Identification Approaches.

    PubMed

    Sayles, Mark; Walls, Michael K; Heinz, Michael G

    2016-01-01

    The compressive nonlinearity of cochlear signal transduction, reflecting outer-hair-cell function, manifests as suppressive spectral interactions; e.g., two-tone suppression. Moreover, for broadband sounds, there are multiple interactions between frequency components. These frequency-dependent nonlinearities are important for neural coding of complex sounds, such as speech. Acoustic-trauma-induced outer-hair-cell damage is associated with loss of nonlinearity, which auditory prostheses attempt to restore with, e.g., "multi-channel dynamic compression" algorithms.Neurophysiological data on suppression in hearing-impaired (HI) mammals are limited. We present data on firing-rate suppression measured in auditory-nerve-fiber responses in a chinchilla model of noise-induced hearing loss, and in normal-hearing (NH) controls at equal sensation level. Hearing-impaired (HI) animals had elevated single-fiber excitatory thresholds (by ~ 20-40 dB), broadened frequency tuning, and reduced-magnitude distortion-product otoacoustic emissions; consistent with mixed inner- and outer-hair-cell pathology. We characterized suppression using two approaches: adaptive tracking of two-tone-suppression threshold (62 NH, and 35 HI fibers), and Wiener-kernel analyses of responses to broadband noise (91 NH, and 148 HI fibers). Suppression-threshold tuning curves showed sensitive low-side suppression for NH and HI animals. High-side suppression thresholds were elevated in HI animals, to the same extent as excitatory thresholds. We factored second-order Wiener-kernels into excitatory and suppressive sub-kernels to quantify the relative strength of suppression. We found a small decrease in suppression in HI fibers, which correlated with broadened tuning. These data will help guide novel amplification strategies, particularly for complex listening situations (e.g., speech in noise), in which current hearing aids struggle to restore intelligibility. PMID:27080669

  12. Suppression Measured from Chinchilla Auditory-Nerve-Fiber Responses Following Noise-Induced Hearing Loss: Adaptive-Tracking and Systems-Identification Approaches.

    PubMed

    Sayles, Mark; Walls, Michael K; Heinz, Michael G

    2016-01-01

    The compressive nonlinearity of cochlear signal transduction, reflecting outer-hair-cell function, manifests as suppressive spectral interactions; e.g., two-tone suppression. Moreover, for broadband sounds, there are multiple interactions between frequency components. These frequency-dependent nonlinearities are important for neural coding of complex sounds, such as speech. Acoustic-trauma-induced outer-hair-cell damage is associated with loss of nonlinearity, which auditory prostheses attempt to restore with, e.g., "multi-channel dynamic compression" algorithms.Neurophysiological data on suppression in hearing-impaired (HI) mammals are limited. We present data on firing-rate suppression measured in auditory-nerve-fiber responses in a chinchilla model of noise-induced hearing loss, and in normal-hearing (NH) controls at equal sensation level. Hearing-impaired (HI) animals had elevated single-fiber excitatory thresholds (by ~ 20-40 dB), broadened frequency tuning, and reduced-magnitude distortion-product otoacoustic emissions; consistent with mixed inner- and outer-hair-cell pathology. We characterized suppression using two approaches: adaptive tracking of two-tone-suppression threshold (62 NH, and 35 HI fibers), and Wiener-kernel analyses of responses to broadband noise (91 NH, and 148 HI fibers). Suppression-threshold tuning curves showed sensitive low-side suppression for NH and HI animals. High-side suppression thresholds were elevated in HI animals, to the same extent as excitatory thresholds. We factored second-order Wiener-kernels into excitatory and suppressive sub-kernels to quantify the relative strength of suppression. We found a small decrease in suppression in HI fibers, which correlated with broadened tuning. These data will help guide novel amplification strategies, particularly for complex listening situations (e.g., speech in noise), in which current hearing aids struggle to restore intelligibility.

  13. Ignorance is bliss: general and robust cancellation of decoherence via no-knowledge quantum feedback.

    PubMed

    Szigeti, Stuart S; Carvalho, Andre R R; Morley, James G; Hush, Michael R

    2014-07-11

    A "no-knowledge" measurement of an open quantum system yields no information about any system observable; it only returns noise input from the environment. Surprisingly, performing such a no-knowledge measurement can be advantageous. We prove that a system undergoing no-knowledge monitoring has reversible noise, which can be canceled by directly feeding back the measurement signal. We show how no-knowledge feedback control can be used to cancel decoherence in an arbitrary quantum system coupled to a Markovian reservoir that is being monitored. Since no-knowledge feedback does not depend on the system state or Hamiltonian, such decoherence cancellation is guaranteed to be general and robust, and can operate in conjunction with any other quantum control protocol. As an application, we show that no-knowledge feedback could be used to improve the performance of dissipative quantum computers subjected to local loss.

  14. Analytical approximations of the firing rate of an adaptive exponential integrate-and-fire neuron in the presence of synaptic noise

    PubMed Central

    Hertäg, Loreen; Durstewitz, Daniel; Brunel, Nicolas

    2014-01-01

    Computational models offer a unique tool for understanding the network-dynamical mechanisms which mediate between physiological and biophysical properties, and behavioral function. A traditional challenge in computational neuroscience is, however, that simple neuronal models which can be studied analytically fail to reproduce the diversity of electrophysiological behaviors seen in real neurons, while detailed neuronal models which do reproduce such diversity are intractable analytically and computationally expensive. A number of intermediate models have been proposed whose aim is to capture the diversity of firing behaviors and spike times of real neurons while entailing the simplest possible mathematical description. One such model is the exponential integrate-and-fire neuron with spike rate adaptation (aEIF) which consists of two differential equations for the membrane potential (V) and an adaptation current (w). Despite its simplicity, it can reproduce a wide variety of physiologically observed spiking patterns, can be fit to physiological recordings quantitatively, and, once done so, is able to predict spike times on traces not used for model fitting. Here we compute the steady-state firing rate of aEIF in the presence of Gaussian synaptic noise, using two approaches. The first approach is based on the 2-dimensional Fokker-Planck equation that describes the (V,w)-probability distribution, which is solved using an expansion in the ratio between the time constants of the two variables. The second is based on the firing rate of the EIF model, which is averaged over the distribution of the w variable. These analytically derived closed-form expressions were tested on simulations from a large variety of model cells quantitatively fitted to in vitro electrophysiological recordings from pyramidal cells and interneurons. Theoretical predictions closely agreed with the firing rate of the simulated cells fed with in-vivo-like synaptic noise. PMID:25278872

  15. Behavioral evaluation of movement cancellation.

    PubMed

    Walton, Mark M G; Gandhi, Neeraj J

    2006-10-01

    The countermanding saccade task has been used in many studies to investigate the neural mechanisms that underlie the decision to execute or restrain rapid eye movements. In this task, the presentation of a saccade target is sometimes followed by the appearance of a stop cue that indicates that the subject should cancel the planned movement. Performance has been modeled as a race between motor preparation and cancellation processes. The signal that reaches its activation threshold first determines whether a saccade is generated or cancelled. In these studies, an important parameter is the time required to process the stop cue, referred to as the stop signal reaction time (SSRT). The SSRT is estimated using statistical approaches, the validity of which has not been unequivocally established. A more direct measure of this parameter might be obtainable if a method was available to "unmask" the developing motor command. This can be accomplished by air-puff-evoked blinks, which inhibit pontine omnipause neurons that serve as an inhibitory gate for the saccadic system. In the present study, brief puffs of air were used to elicit blinks at various times while rhesus monkeys performed a countermanding saccade task. If the developing motor command has not yet been cancelled, this should trigger a saccade. When blinks occurred between approximately 50 and 200 ms after target onset, saccades were often evoked. Saccades were rarely evoked more than approximately 70 ms after stop cue onset; this value represents a behavioral evaluation of SSRT and was comparable to the estimates obtained using standard statistical approaches. When saccades occurred near the SSRT on blink trials, they were often hypometric. Furthermore, Monte Carlo simulations were performed to model the effects of blink time on the race model. Overall, the study supports the validity of the statistical methods currently in use. PMID:16760340

  16. Active noise control: A tutorial for HVAC designers

    SciTech Connect

    Gelin, L.J.

    1997-08-01

    This article will identify the capabilities and limitations of ANC in its application to HVAC noise control. ANC can be used in ducted HVAC systems to cancel ductborne, low-frequency fan noise by injecting sound waves of equal amplitude and opposite phase into an air duct, as close as possible to the source of the unwanted noise. Destructive interference of the fan noise and injected noise results in sound cancellation. The noise problems that it solves are typically described as rumble, roar or throb, all of which are difficult to address using traditional noise control methods. This article will also contrast the use of active against passive noise control techniques. The main differences between the two noise control measures are acoustic performance, energy consumption, and design flexibility. The article will first present the fundamentals and basic physics of ANC. The application to real HVAC systems will follow.

  17. Biohybrid Control of General Linear Systems Using the Adaptive Filter Model of Cerebellum

    PubMed Central

    Wilson, Emma D.; Assaf, Tareq; Pearson, Martin J.; Rossiter, Jonathan M.; Dean, Paul; Anderson, Sean R.; Porrill, John

    2015-01-01

    The adaptive filter model of the cerebellar microcircuit has been successfully applied to biological motor control problems, such as the vestibulo-ocular reflex (VOR), and to sensory processing problems, such as the adaptive cancelation of reafferent noise. It has also been successfully applied to problems in robotics, such as adaptive camera stabilization and sensor noise cancelation. In previous applications to inverse control problems, the algorithm was applied to the velocity control of a plant dominated by viscous and elastic elements. Naive application of the adaptive filter model to the displacement (as opposed to velocity) control of this plant results in unstable learning and control. To be more generally useful in engineering problems, it is essential to remove this restriction to enable the stable control of plants of any order. We address this problem here by developing a biohybrid model reference adaptive control (MRAC) scheme, which stabilizes the control algorithm for strictly proper plants. We evaluate the performance of this novel cerebellar-inspired algorithm with MRAC scheme in the experimental control of a dielectric electroactive polymer, a class of artificial muscle. The results show that the augmented cerebellar algorithm is able to accurately control the displacement response of the artificial muscle. The proposed solution not only greatly extends the practical applicability of the cerebellar-inspired algorithm, but may also shed light on cerebellar involvement in a wider range of biological control tasks. PMID:26257638

  18. Approximated affine projection algorithm for feedback cancellation in hearing aids.

    PubMed

    Lee, Sangmin; Kim, In-Young; Park, Young-Cheol

    2007-09-01

    We propose an approximated affine projection (AP) algorithm for feedback cancellation in hearing aids. It is based on the conventional approach using the Gauss-Seidel (GS) iteration, but provides more stable convergence behaviour even with small step sizes. In the proposed algorithm, a residue of the weighted error vector, instead of the current error sample, is used to provide stable convergence. A new learning rate control scheme is also applied to the proposed algorithm to prevent signal cancellation and system instability. The new scheme determines step size in proportion to the prediction factor of the input, so that adaptation is inhibited whenever tone-like signals are present in the input. Simulation results verified the efficiency of the proposed algorithm. PMID:17644214

  19. Adaptive filtering in biological signal processing.

    PubMed

    Iyer, V K; Ploysongsang, Y; Ramamoorthy, P A

    1990-01-01

    The high dependence of conventional optimal filtering methods on the a priori knowledge of the signal and noise statistics render them ineffective in dealing with signals whose statistics cannot be predetermined accurately. Adaptive filtering methods offer a better alternative, since the a priori knowledge of statistics is less critical, real time processing is possible, and the computations are less expensive for this approach. Adaptive filtering methods compute the filter coefficients "on-line", converging to the optimal values in the least-mean square (LMS) error sense. Adaptive filtering is therefore apt for dealing with the "unknown" statistics situation and has been applied extensively in areas like communication, speech, radar, sonar, seismology, and biological signal processing and analysis for channel equalization, interference and echo canceling, line enhancement, signal detection, system identification, spectral analysis, beamforming, modeling, control, etc. In this review article adaptive filtering in the context of biological signals is reviewed. An intuitive approach to the underlying theory of adaptive filters and its applicability are presented. Applications of the principles in biological signal processing are discussed in a manner that brings out the key ideas involved. Current and potential future directions in adaptive biological signal processing are also discussed.

  20. Bayesian nonparametric adaptive control using Gaussian processes.

    PubMed

    Chowdhary, Girish; Kingravi, Hassan A; How, Jonathan P; Vela, Patricio A

    2015-03-01

    Most current model reference adaptive control (MRAC) methods rely on parametric adaptive elements, in which the number of parameters of the adaptive element are fixed a priori, often through expert judgment. An example of such an adaptive element is radial basis function networks (RBFNs), with RBF centers preallocated based on the expected operating domain. If the system operates outside of the expected operating domain, this adaptive element can become noneffective in capturing and canceling the uncertainty, thus rendering the adaptive controller only semiglobal in nature. This paper investigates a Gaussian process-based Bayesian MRAC architecture (GP-MRAC), which leverages the power and flexibility of GP Bayesian nonparametric models of uncertainty. The GP-MRAC does not require the centers to be preallocated, can inherently handle measurement noise, and enables MRAC to handle a broader set of uncertainties, including those that are defined as distributions over functions. We use stochastic stability arguments to show that GP-MRAC guarantees good closed-loop performance with no prior domain knowledge of the uncertainty. Online implementable GP inference methods are compared in numerical simulations against RBFN-MRAC with preallocated centers and are shown to provide better tracking and improved long-term learning.

  1. 34 CFR 674.59 - Cancellation for military service.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 34 Education 3 2014-07-01 2014-07-01 false Cancellation for military service. 674.59 Section 674... Cancellation for military service. (a) Cancellation on a Defense loan. (1) An institution must cancel up to 50... fraction of a year beyond a complete year of service, does not qualify for military cancellation....

  2. 34 CFR 674.59 - Cancellation for military service.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 34 Education 3 2012-07-01 2012-07-01 false Cancellation for military service. 674.59 Section 674... Cancellation for military service. (a) Cancellation on a Defense loan. (1) An institution must cancel up to 50... fraction of a year beyond a complete year of service, does not qualify for military cancellation....

  3. 34 CFR 674.59 - Cancellation for military service.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 34 Education 3 2013-07-01 2013-07-01 false Cancellation for military service. 674.59 Section 674... Cancellation for military service. (a) Cancellation on a Defense loan. (1) An institution must cancel up to 50... fraction of a year beyond a complete year of service, does not qualify for military cancellation....

  4. Performance analysis of approximate Affine Projection Algorithm in acoustic feedback cancellation.

    PubMed

    Nikjoo S, Mohammad; Seyedi, Amir; Tehrani, Arash Saber

    2008-01-01

    Acoustic feedback is an annoying problem in several audio applications and especially in hearing aids. Adaptive feedback cancellation techniques have attracted recent attention and show great promise in reducing the deleterious effects of feedback. In this paper, we investigated the performance of a class of adaptive feedback cancellation algorithms viz. the approximated Affine Projection Algorithms (APA). Mixed results were obtained with the natural speech and music data collected from five different commercial hearing aids in a variety of sub-oscillatory and oscillatory feedback conditions. The performance of the approximated APA was significantly better with music stimuli than natural speech stimuli. PMID:19162642

  5. 29 CFR 4.190 - Contract cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., the contract is subject upon written notice to cancellation by the contracting agency, whereupon the... contract is similarly subject upon written notice to immediate cancellation by the contracting agency and... in paragraph (a). Such contract is without warrant of law and has no force and effect and is void...

  6. 25 CFR 214.19 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 1 2014-04-01 2014-04-01 false Cancellation. 214.19 Section 214.19 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF OSAGE RESERVATION LANDS, OKLAHOMA, FOR MINING, EXCEPT OIL AND GAS § 214.19 Cancellation. When a lessee makes application for...

  7. 25 CFR 213.40 - Cancellations.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 1 2013-04-01 2013-04-01 false Cancellations. 213.40 Section 213.40 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF RESTRICTED LANDS OF MEMBERS OF FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the...

  8. 25 CFR 214.19 - Cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 1 2012-04-01 2011-04-01 true Cancellation. 214.19 Section 214.19 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF OSAGE RESERVATION LANDS, OKLAHOMA, FOR MINING, EXCEPT OIL AND GAS § 214.19 Cancellation. When a lessee makes application for...

  9. 25 CFR 213.40 - Cancellations.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 1 2014-04-01 2014-04-01 false Cancellations. 213.40 Section 213.40 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF RESTRICTED LANDS OF MEMBERS OF FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the...

  10. 25 CFR 213.40 - Cancellations.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 1 2012-04-01 2011-04-01 true Cancellations. 213.40 Section 213.40 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF RESTRICTED LANDS OF MEMBERS OF FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the...

  11. 25 CFR 214.19 - Cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 1 2011-04-01 2011-04-01 false Cancellation. 214.19 Section 214.19 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF OSAGE RESERVATION LANDS, OKLAHOMA, FOR MINING, EXCEPT OIL AND GAS § 214.19 Cancellation. When a lessee makes application for...

  12. 25 CFR 214.19 - Cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 1 2013-04-01 2013-04-01 false Cancellation. 214.19 Section 214.19 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF OSAGE RESERVATION LANDS, OKLAHOMA, FOR MINING, EXCEPT OIL AND GAS § 214.19 Cancellation. When a lessee makes application for...

  13. 25 CFR 227.28 - Cancellations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Cancellations. 227.28 Section 227.28 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF CERTAIN LANDS IN WIND RIVER INDIAN RESERVATION, WYOMING, FOR OIL AND GAS MINING Operations § 227.28 Cancellations. Leases shall...

  14. 25 CFR 227.28 - Cancellations.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 1 2012-04-01 2011-04-01 true Cancellations. 227.28 Section 227.28 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF CERTAIN LANDS IN WIND RIVER INDIAN RESERVATION, WYOMING, FOR OIL AND GAS MINING Operations § 227.28 Cancellations. Leases shall...

  15. 25 CFR 227.28 - Cancellations.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 1 2011-04-01 2011-04-01 false Cancellations. 227.28 Section 227.28 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF CERTAIN LANDS IN WIND RIVER INDIAN RESERVATION, WYOMING, FOR OIL AND GAS MINING Operations § 227.28 Cancellations. Leases shall...

  16. 25 CFR 227.28 - Cancellations.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 1 2013-04-01 2013-04-01 false Cancellations. 227.28 Section 227.28 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF CERTAIN LANDS IN WIND RIVER INDIAN RESERVATION, WYOMING, FOR OIL AND GAS MINING Operations § 227.28 Cancellations. Leases shall...

  17. 25 CFR 227.28 - Cancellations.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 1 2014-04-01 2014-04-01 false Cancellations. 227.28 Section 227.28 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF CERTAIN LANDS IN WIND RIVER INDIAN RESERVATION, WYOMING, FOR OIL AND GAS MINING Operations § 227.28 Cancellations. Leases shall...

  18. 34 CFR 674.52 - Cancellation procedures.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... borrower's loan deferment under § 674.34(c) to run concurrently with any period for which cancellation... run concurrently with any period for which a cancellation under §§ 674.53, 674.56, 674.57, or 674.58 is granted. (e) National community service. No borrower who has received a benefit under subtitle...

  19. 25 CFR 23.53 - Cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Cancellation. 23.53 Section 23.53 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR HUMAN SERVICES INDIAN CHILD WELFARE ACT General and Uniform Grant Administration Provisions and Requirements § 23.53 Cancellation. (a) The grants officer may...

  20. 43 CFR 3601.62 - Cancellation procedure.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Disposal; General Provisions Contract and Permit Cancellation § 3601.62 Cancellation procedure. (a... notice under paragraph (a) of this section, or if delivery of the notice is refused, or not completed...

  1. 36 CFR 223.116 - Cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Timber Sale Contracts Contract Administration § 223.116 Cancellation. (a) Timber sale contracts and permits may be canceled: (1) For serious or continued violation of... the value of the timber remaining to be cut is diminished materially because of catastrophic...

  2. 7 CFR 1942.12 - Loan cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATIONS (CONTINUED) ASSOCIATIONS Community Facility Loans § 1942.12 Loan cancellation. Loans which have... Development Manager or State Director may prepare and execute Form Rural Development 1940-10, Cancellation of... disbursement has been received or is subsequently received in the Area Office, the Rural Development...

  3. 34 CFR 674.52 - Cancellation procedures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... covered under the Family and Medical Leave Act of 1993 (FMLA) (29 U.S.C. 2601, et seq.), the borrower... cancellation based on a claim of simultaneous employment as a nurse or medical technician in two or more... of title I of the National and Community Service Act of 1990 may receive a cancellation under......

  4. 43 CFR 3601.62 - Cancellation procedure.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Disposal; General Provisions Contract and Permit Cancellation § 3601.62 Cancellation procedure. (a... notice under paragraph (a) of this section, or if delivery of the notice is refused, or not completed...

  5. 44 CFR 206.376 - Loan cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.376 Loan cancellation. (a) FEMA shall cancel repayment of all or part of a Special Community Disaster Loan to the extent... Special Community Disaster loans issued from the dates of enactment of Public Law 109-88 and Public...

  6. 44 CFR 206.376 - Loan cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.376 Loan cancellation. (a) FEMA shall cancel repayment of all or part of a Special Community Disaster Loan to the extent... Special Community Disaster loans issued from the dates of enactment of Public Law 109-88 and Public...

  7. 44 CFR 206.366 - Loan cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.366 Loan cancellation. (a) Policies. (1) FEMA shall cancel repayment of all or part of a Community Disaster Loan to the... incurred for general government purposes, such as police and fire protection, trash collection,...

  8. 44 CFR 206.366 - Loan cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.366 Loan cancellation. (a) Policies. (1) FEMA shall cancel repayment of all or part of a Community Disaster Loan to the... incurred for general government purposes, such as police and fire protection, trash collection,...

  9. 44 CFR 206.376 - Loan cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.376 Loan cancellation. (a) FEMA shall cancel repayment of all or part of a Special Community Disaster Loan to the extent... Special Community Disaster loans issued from the dates of enactment of Public Law 109-88 and Public...

  10. 44 CFR 206.366 - Loan cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.366 Loan cancellation. (a) Policies. (1) FEMA shall cancel repayment of all or part of a Community Disaster Loan to the... incurred for general government purposes, such as police and fire protection, trash collection,...

  11. 44 CFR 206.366 - Loan cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... HOMELAND SECURITY DISASTER ASSISTANCE FEDERAL DISASTER ASSISTANCE Community Disaster Loans § 206.366 Loan cancellation. (a) Policies. (1) FEMA shall cancel repayment of all or part of a Community Disaster Loan to the... incurred for general government purposes, such as police and fire protection, trash collection,...

  12. 7 CFR 1956.70 - Cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... REGULATIONS (CONTINUED) DEBT SETTLEMENT Debt Settlement-Farm Loan Programs and Multi-Family Housing § 1956.70 Cancellation. Nonjudgment debts may be canceled in the following instances: (a) With application. The debt or any extension thereof on Farmer Programs debts do not have to be due and payable under the terms...

  13. High phase noise tolerant pilot-tone-aided DP-QPSK optical communication systems.

    PubMed

    Zhang, Xu; Pang, Xiaodan; Deng, Lei; Zibar, Darko; Monroy, Idelfonso Tafur; Younce, Richard

    2012-08-27

    In this paper we experimentally demonstrate a novel, high phase-noise tolerant, optical dual polarization (DP) quadrature phase-shift keying (QPSK) communication system based on pilot-tone-aided phase noise cancellation (PNC) algorithm. Vertical cavity surface emitting lasers (VCSELs) with approximate 300 MHz linewidth are used as transmitters and local oscillators for coherent detection of optical DP-QPSK signals. The proposed system, with central wavelength at 1540.68 nm, operates at 40 Gb/s over 80 km single mode fiber (SMF) as part of a passive optical network (PON). The deployment of pilot-tone-aided PNC algorithm guarantees a bit error rate (BER) performance below the forward error correction (FEC) threshold. Moreover, we also evaluate a novel digital signal processing (DSP) algorithm for adaptive pilot tone detection.

  14. Adaptive array for weak interfering signals: Geostationary satellite experiments

    NASA Astrophysics Data System (ADS)

    Steadman, Karl

    The performance of an experimental adaptive array is evaluated using signals from an existing geostationary satellite interference environment. To do this, an earth station antenna was built to receive signals from various geostationary satellites. In these experiments the received signals have a frequency of approximately 4 GHz (C-band) and have a bandwidth of over 35 MHz. These signals are downconverted to a 69 MHz intermediate frequency in the experimental system. Using the downconverted signals, the performance of the experimental system for various signal scenarios is evaluated. In this situation, due to the inherent thermal noise, qualitative instead of quantitative test results are presented. It is shown that the experimental system can null up to two interfering signals well below the noise level. However, to avoid the cancellation of the desired signal, the use a steering vector is needed. Various methods to obtain an estimate of the steering vector are proposed.

  15. Nuclear plant cancellations: causes, costs, and consequences

    SciTech Connect

    Not Available

    1983-04-01

    This study was commissioned in order to help quantify the effects of nuclear plant cancellations on the Nation's electricity prices. This report presents a historical overview of nuclear plant cancellations through 1982, the costs associated with those cancellations, and the reasons that the projects were terminated. A survey is presented of the precedents for regulatory treatment of the costs, the specific methods of cost recovery that were adopted, and the impacts of these decisions upon ratepayers, utility stockholders, and taxpayers. Finally, the report identifies a series of other nuclear plants that remain at risk of canellation in the future, principally as a result of similar demand, finance, or regulatory problems cited as causes of cancellation in the past. The costs associated with these potential cancellations are estimated, along with their regional distributions, and likely methods of cost recovery are suggested.

  16. Reward Improves Cancellation and Restraint Inhibition Across Childhood and Adolescence

    PubMed Central

    Sinopoli, Katia J.; Schachar, Russell; Dennis, Maureen

    2011-01-01

    Inhibitory control allows for the regulation of thought and action, and interacts with motivational variables, such as reward, to modify behavior adaptively as environments change. We examined the effects of reward on two distinct forms of inhibitory control, cancellation and restraint. Typically developing children and adolescents completed two versions of the stop signal task (cancellation and restraint) under three reward conditions (neutral, low reward, and high reward), where rewards were earned for successful inhibitory control. Rewards improved both cancellation and restraint inhibition, with similar effects of reward on each form of inhibitory control. Rewards did not alter the speed of response execution in either task, suggesting that rewards specifically altered inhibition processes without influencing processes related to response execution. Adolescents were faster and less variable than children when executing and inhibiting their responses. There were similar developmental effects of reward on the speed of inhibitory control, but group differences were found in terms of accuracy of inhibition in the restraint task. These results clarify how reward modulates two different forms of regulatory behavior in children and adolescents. PMID:21744952

  17. 78 FR 48456 - Notice of Cancellation of Customs Broker Licenses

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-08

    ... permits of certain customs brokers are being cancelled without prejudice. SUPPLEMENTARY INFORMATION... following customs broker licenses are cancelled without prejudice. ] Last/company name First name License...

  18. Brillouin scattering self-cancellation.

    PubMed

    Florez, O; Jarschel, P F; Espinel, Y A V; Cordeiro, C M B; Mayer Alegre, T P; Wiederhecker, G S; Dainese, P

    2016-01-01

    The interaction between light and acoustic phonons is strongly modified in sub-wavelength confinement, and has led to the demonstration and control of Brillouin scattering in photonic structures such as nano-scale optical waveguides and cavities. Besides the small optical mode volume, two physical mechanisms come into play simultaneously: a volume effect caused by the strain-induced refractive index perturbation (known as photo-elasticity), and a surface effect caused by the shift of the optical boundaries due to mechanical vibrations. As a result, proper material and structure engineering allows one to control each contribution individually. Here, we experimentally demonstrate the perfect cancellation of Brillouin scattering arising from Rayleigh acoustic waves by engineering a silica nanowire with exactly opposing photo-elastic and moving-boundary effects. This demonstration provides clear experimental evidence that the interplay between the two mechanisms is a promising tool to precisely control the photon-phonon interaction, enhancing or suppressing it. PMID:27283092

  19. Brillouin scattering self-cancellation

    NASA Astrophysics Data System (ADS)

    Florez, O.; Jarschel, P. F.; Espinel, Y. A. V.; Cordeiro, C. M. B.; Mayer Alegre, T. P.; Wiederhecker, G. S.; Dainese, P.

    2016-06-01

    The interaction between light and acoustic phonons is strongly modified in sub-wavelength confinement, and has led to the demonstration and control of Brillouin scattering in photonic structures such as nano-scale optical waveguides and cavities. Besides the small optical mode volume, two physical mechanisms come into play simultaneously: a volume effect caused by the strain-induced refractive index perturbation (known as photo-elasticity), and a surface effect caused by the shift of the optical boundaries due to mechanical vibrations. As a result, proper material and structure engineering allows one to control each contribution individually. Here, we experimentally demonstrate the perfect cancellation of Brillouin scattering arising from Rayleigh acoustic waves by engineering a silica nanowire with exactly opposing photo-elastic and moving-boundary effects. This demonstration provides clear experimental evidence that the interplay between the two mechanisms is a promising tool to precisely control the photon-phonon interaction, enhancing or suppressing it.

  20. Brillouin scattering self-cancellation

    PubMed Central

    Florez, O.; Jarschel, P. F.; Espinel, Y. A. V.; Cordeiro, C. M. B.; Mayer Alegre, T. P.; Wiederhecker, G. S.; Dainese, P.

    2016-01-01

    The interaction between light and acoustic phonons is strongly modified in sub-wavelength confinement, and has led to the demonstration and control of Brillouin scattering in photonic structures such as nano-scale optical waveguides and cavities. Besides the small optical mode volume, two physical mechanisms come into play simultaneously: a volume effect caused by the strain-induced refractive index perturbation (known as photo-elasticity), and a surface effect caused by the shift of the optical boundaries due to mechanical vibrations. As a result, proper material and structure engineering allows one to control each contribution individually. Here, we experimentally demonstrate the perfect cancellation of Brillouin scattering arising from Rayleigh acoustic waves by engineering a silica nanowire with exactly opposing photo-elastic and moving-boundary effects. This demonstration provides clear experimental evidence that the interplay between the two mechanisms is a promising tool to precisely control the photon–phonon interaction, enhancing or suppressing it. PMID:27283092

  1. Background canceling surface alpha detector

    DOEpatents

    MacArthur, Duncan W.; Allander, Krag S.; Bounds, John A.

    1996-01-01

    A background canceling long range alpha detector which is capable of providing output proportional to both the alpha radiation emitted from a surface and to radioactive gas emanating from the surface. The detector operates by using an electrical field between first and second signal planes, an enclosure and the surface or substance to be monitored for alpha radiation. The first and second signal planes are maintained at the same voltage with respect to the electrically conductive enclosure, reducing leakage currents. In the presence of alpha radiation and radioactive gas decay, the signal from the first signal plane is proportional to both the surface alpha radiation and to the airborne radioactive gas, while the signal from the second signal plane is proportional only to the airborne radioactive gas. The difference between these two signals is proportional to the surface alpha radiation alone.

  2. Background canceling surface alpha detector

    DOEpatents

    MacArthur, D.W.; Allander, K.S.; Bounds, J.A.

    1996-06-11

    A background canceling long range alpha detector which is capable of providing output proportional to both the alpha radiation emitted from a surface and to radioactive gas emanating from the surface. The detector operates by using an electrical field between first and second signal planes, an enclosure and the surface or substance to be monitored for alpha radiation. The first and second signal planes are maintained at the same voltage with respect to the electrically conductive enclosure, reducing leakage currents. In the presence of alpha radiation and radioactive gas decay, the signal from the first signal plane is proportional to both the surface alpha radiation and to the airborne radioactive gas, while the signal from the second signal plane is proportional only to the airborne radioactive gas. The difference between these two signals is proportional to the surface alpha radiation alone. 5 figs.

  3. Voice interactive systems in severe noise conditions

    NASA Astrophysics Data System (ADS)

    Steeneken, J. H. M.; Langhout, G.

    1987-02-01

    In a comparison of word recognition performance between human listeners and automatic speech recognition systems (ASR), the human listeners performs much better, especially in severe noise conditions. An application engineer can try to optimize the performance of an ASR system by selecting the optimal noise cancelling microphone and vocabulary for voice input. Some results from a study on the effect of signal handling and vocabulary configuration on the performance of voice input and voice output systems are discussed.

  4. Improved Iterative Parallel Interference Cancellation Receiver for Future Wireless DS-CDMA Systems

    NASA Astrophysics Data System (ADS)

    Morosi, Simone; Fantacci, Romano; Bernacchioni, Andrea

    2005-12-01

    We present a new turbo multiuser detector for turbo-coded direct sequence code division multiple access (DS-CDMA) systems. The proposed detector is based on the utilization of a parallel interference cancellation (PIC) and a bank of turbo decoders. The PIC is broken up in order to perform interference cancellation after each constituent decoder of the turbo decoding scheme. Moreover, in the paper we propose a new enhanced algorithm that provides a more accurate estimation of the signal-to-noise-plus-interference-ratio used in the tentative decision device and in the MAP decoding algorithm. The performance of the proposed receiver is evaluated by means of computer simulations for medium to very high system loads, in AWGN and multipath fading channel, and compared to recently proposed interference cancellation-based iterative MUD, by taking into account the number of iterations and the complexity involved. We will see that the proposed receiver outperforms the others especially for highly loaded systems.

  5. Magnetic Flux Cancellation and Formation of Prominence

    NASA Astrophysics Data System (ADS)

    Miley, George; Kim, Mun Song; Chon Nam, Sok; Kim, Kyong Chol

    2015-08-01

    Magnetic flux cancellation appears to be closely related to various kinds of solar activities such as flares, microflares/surges/jets, X-ray bright points, erupting mini-filaments, transition region explosive events, filament formation, filament activation and eruption, and coronal mass ejections. It is commonly believed that magnetic reconnections in the low atmosphere are responsible for canceling magnetic features, and magnetic fragments are observed to originate as bipoles. According to the Sweet-Parker type reconnection model, the inflow speed closely corresponds to the converging speed of each pole in a canceling magnetic feature and the rate of flux cancellation must be explained by the observed converging speed. As distinct from the corona, the efficiency of photospheric magnetic reconnection may be due to the small Cowling conductivity, instead of the Spitzer, of weakly ionized and magnetized plasma in the low atmosphere of the sun. Using the VAL-C atmospheric model and Cowling conductivity, we have computed the parameters describing Sweet-Parker type reconnecting current sheets in the plasma of the solar photosphere and chromosphere, and particularly for the phenomena of magnetic flux cancellation and dark filament formation which occurred on July 2, 1994 we have estimated the rate of flux cancellation, the inflow speed(the converging speed) and the upward mass flux to compare with the observation. The results show that when taking account of the Cowling conductivity in the low atmosphere, large flux cancellation rates(>1019Mxhr-1) in solar active regions are better explained than by the Spitzer conductivity-considered reconnection model. Particularly for the flux cancellation event on July 2, 1994, the inflow speed(0.26kms-1)is almost similar to the converging speed(0.22kms-1)and the upward mass flux(3.3X1012gs-1) in the model is sufficient for the large dark filament formation in a time of several hours through magnetic flux cancellation process.

  6. Rotorcraft noise

    NASA Technical Reports Server (NTRS)

    Huston, R. J. (Compiler)

    1982-01-01

    The establishment of a realistic plan for NASA and the U.S. helicopter industry to develop a design-for-noise methodology, including plans for the identification and development of promising noise reduction technology was discussed. Topics included: noise reduction techniques, scaling laws, empirical noise prediction, psychoacoustics, and methods of developing and validing noise prediction methods.

  7. Noise control using a plate radiator and an acoustic resonator

    NASA Technical Reports Server (NTRS)

    Pla, Frederic G. (Inventor)

    1996-01-01

    An active noise control subassembly for reducing noise caused by a source (such as an aircraft engine) independent of the subassembly. A noise radiating panel is bendably vibratable to generate a panel noise canceling at least a portion of the source noise. A piezoceramic actuator plate is connected to the panel. A front plate is spaced apart from the panel and the first plate, is positioned generally between the source noise and the panel, and has a sound exit port. A first pair of spaced-apart side walls each generally abut the panel and the front plate so as to generally enclose a front cavity to define a resonator.

  8. Observation of radiation-pressure effects and back-action cancellation in interferometric measurements

    NASA Astrophysics Data System (ADS)

    Heidmann, A.; Caniard, T.; Verlot, P.; Briant, T.; Cohadon, P.-F.

    2008-02-01

    Radiation pressure exerted by light in interferometric measurements is responsible for displacements of mirrors which appear as an additional back-action noise and limit the sensitivity of the measurement. We experimentally study these effects by monitoring in a very highfinesse optical cavity the displacements of a mirror with a sensitivity at the 10 -20 m/√Hz level. This unique sensitivity is a step towards the first observation of the fundamental quantum effects of radiation pressure and the resulting standard quantum limit in interferometric measurements. Our experiment may become a powerful facility to test quantum noise reduction schemes, and we already report the first experimental demonstration of a back-action noise cancellation. Using a classical radiation-pressure noise to mimic the quantum noise of light, we have observed a drastic improvement of sensitivity both in position and force measurements.

  9. 42 CFR 493.1842 - Cancellation of Medicare approval.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) Written notice of the rationale for, effective date, and effect of, cancellation; (2) Opportunity to submit written evidence or other information against cancellation of the laboratory's approval. This... appeals procedures set forth in § 493.1844. (c) Effect of cancellation. Cancellation of Medicare...

  10. 43 CFR 3452.2-1 - Cause for cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Cause for cancellation. 3452.2-1 Section... Relinquishment, Cancellation, and Termination § 3452.2-1 Cause for cancellation. (a) The authorized officer... continued operation requirements shall be subject to cancellation in whole or in part. In deciding...

  11. 43 CFR 3452.2-1 - Cause for cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Cause for cancellation. 3452.2-1 Section... Relinquishment, Cancellation, and Termination § 3452.2-1 Cause for cancellation. (a) The authorized officer... continued operation requirements shall be subject to cancellation in whole or in part. In deciding...

  12. 43 CFR 3452.2-1 - Cause for cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Cause for cancellation. 3452.2-1 Section... Relinquishment, Cancellation, and Termination § 3452.2-1 Cause for cancellation. (a) The authorized officer... continued operation requirements shall be subject to cancellation in whole or in part. In deciding...

  13. 43 CFR 3452.2-1 - Cause for cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Cause for cancellation. 3452.2-1 Section... Relinquishment, Cancellation, and Termination § 3452.2-1 Cause for cancellation. (a) The authorized officer... continued operation requirements shall be subject to cancellation in whole or in part. In deciding...

  14. 18 CFR 4.83 - Cancellation and loss of priority.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... opportunity for hearing. Cancellation of a permit will result in loss of the permittee's priority of... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Cancellation and loss... Permit § 4.83 Cancellation and loss of priority. (a) The Commission may cancel a preliminary permit...

  15. 18 CFR 4.83 - Cancellation and loss of priority.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... opportunity for hearing. Cancellation of a permit will result in loss of the permittee's priority of... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Cancellation and loss... Permit § 4.83 Cancellation and loss of priority. (a) The Commission may cancel a preliminary permit...

  16. 12 CFR 209.3 - Cancellation of Reserve Bank stock.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 2 2010-01-01 2010-01-01 false Cancellation of Reserve Bank stock. 209.3... ISSUE AND CANCELLATION OF FEDERAL RESERVE BANK CAPITAL STOCK (REGULATION I) § 209.3 Cancellation of Reserve Bank stock. (a) Application for cancellation. Any bank that desires to withdraw from membership...

  17. 34 CFR 674.59 - Cancellation for military service.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... balance on an NDSL or Perkins loan for active duty service that ended before August 14, 2008, as a member... 34 Education 3 2011-07-01 2011-07-01 false Cancellation for military service. 674.59 Section 674... Cancellation for military service. (a) Cancellation on a Defense loan. (1) An institution must cancel up to...

  18. 42 CFR 493.1842 - Cancellation of Medicare approval.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Cancellation of Medicare approval. 493.1842 Section 493.1842 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... Cancellation of Medicare approval. (a) Basis for cancellation. (1) CMS always cancels a laboratory's...

  19. 18 CFR 4.83 - Cancellation and loss of priority.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Cancellation and loss... Permit § 4.83 Cancellation and loss of priority. (a) The Commission may cancel a preliminary permit after... opportunity for hearing. Cancellation of a permit will result in loss of the permittee's priority...

  20. 18 CFR 4.83 - Cancellation and loss of priority.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Cancellation and loss... Permit § 4.83 Cancellation and loss of priority. (a) The Commission may cancel a preliminary permit after... opportunity for hearing. Cancellation of a permit will result in loss of the permittee's priority...

  1. 18 CFR 4.83 - Cancellation and loss of priority.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Cancellation and loss... Permit § 4.83 Cancellation and loss of priority. (a) The Commission may cancel a preliminary permit after... opportunity for hearing. Cancellation of a permit will result in loss of the permittee's priority...

  2. Effective Topological Charge Cancelation Mechanism

    PubMed Central

    Mesarec, Luka; Góźdź, Wojciech; Iglič, Aleš; Kralj, Samo

    2016-01-01

    Topological defects (TDs) appear almost unavoidably in continuous symmetry breaking phase transitions. The topological origin makes their key features independent of systems’ microscopic details; therefore TDs display many universalities. Because of their strong impact on numerous material properties and their significant role in several technological applications it is of strong interest to find simple and robust mechanisms controlling the positioning and local number of TDs. We present a numerical study of TDs within effectively two dimensional closed soft films exhibiting in-plane orientational ordering. Popular examples of such class of systems are liquid crystalline shells and various biological membranes. We introduce the Effective Topological Charge Cancellation mechanism controlling localised positional assembling tendency of TDs and the formation of pairs {defect, antidefect} on curved surfaces and/or presence of relevant “impurities” (e.g. nanoparticles). For this purpose, we define an effective topological charge Δmeff consisting of real, virtual and smeared curvature topological charges within a surface patch Δς identified by the typical spatially averaged local Gaussian curvature K. We demonstrate a strong tendency enforcing Δmeff → 0 on surfaces composed of Δς exhibiting significantly different values of spatially averaged K. For Δmeff ≠ 0 we estimate a critical depinning threshold to form pairs {defect, antidefect} using the electrostatic analogy. PMID:27250777

  3. Effective Topological Charge Cancelation Mechanism

    NASA Astrophysics Data System (ADS)

    Mesarec, Luka; Góźdź, Wojciech; Iglič, Aleš; Kralj, Samo

    2016-06-01

    Topological defects (TDs) appear almost unavoidably in continuous symmetry breaking phase transitions. The topological origin makes their key features independent of systems’ microscopic details; therefore TDs display many universalities. Because of their strong impact on numerous material properties and their significant role in several technological applications it is of strong interest to find simple and robust mechanisms controlling the positioning and local number of TDs. We present a numerical study of TDs within effectively two dimensional closed soft films exhibiting in-plane orientational ordering. Popular examples of such class of systems are liquid crystalline shells and various biological membranes. We introduce the Effective Topological Charge Cancellation mechanism controlling localised positional assembling tendency of TDs and the formation of pairs {defect, antidefect} on curved surfaces and/or presence of relevant “impurities” (e.g. nanoparticles). For this purpose, we define an effective topological charge Δmeff consisting of real, virtual and smeared curvature topological charges within a surface patch Δς identified by the typical spatially averaged local Gaussian curvature K. We demonstrate a strong tendency enforcing Δmeff → 0 on surfaces composed of Δς exhibiting significantly different values of spatially averaged K. For Δmeff ≠ 0 we estimate a critical depinning threshold to form pairs {defect, antidefect} using the electrostatic analogy.

  4. ANOMALY STRUCTURE OF SUPERGRAVITY AND ANOMALY CANCELLATION

    SciTech Connect

    Butter, Daniel; Gaillard, Mary K.

    2009-06-10

    We display the full anomaly structure of supergravity, including new D-term contributions to the conformal anomaly. This expression has the super-Weyl and chiral U(1){sub K} transformation properties that are required for implementation of the Green-Schwarz mechanism for anomaly cancellation. We outline the procedure for full anomaly cancellation. Our results have implications for effective supergravity theories from the weakly coupled heterotic string theory.

  5. Order selection of the hearing aid Feedback Canceller filter based on its impulse response energy.

    PubMed

    Khoubrouy, Soudeh A; Panahi, Issa M S

    2012-01-01

    Numerous methods have been proposed to cancel the unpleasant effects of acoustic feedback between the loudspeaker and microphone in hearing aid systems. Adaptive Feedback Cancellation (AFC) methods are often used to estimate an FIR filter for cancelling the feedback path effect. In estimating the AFC FIR filter, it is important to select the order of the filter properly; especially when the feedback path changes from one environment to another and no knowledge about it is available. Choosing improper filter order causes deficient system performance or excessive computations and power usage in the system. We present tracking of the energy of AFC FIR filters and its convergence behavior as a new criterion for determining the proper order for AFC FIR filter. Experimental results show validity of the proposed criterion.

  6. Order selection of the hearing aid Feedback Canceller filter based on its impulse response energy.

    PubMed

    Khoubrouy, Soudeh A; Panahi, Issa M S

    2012-01-01

    Numerous methods have been proposed to cancel the unpleasant effects of acoustic feedback between the loudspeaker and microphone in hearing aid systems. Adaptive Feedback Cancellation (AFC) methods are often used to estimate an FIR filter for cancelling the feedback path effect. In estimating the AFC FIR filter, it is important to select the order of the filter properly; especially when the feedback path changes from one environment to another and no knowledge about it is available. Choosing improper filter order causes deficient system performance or excessive computations and power usage in the system. We present tracking of the energy of AFC FIR filters and its convergence behavior as a new criterion for determining the proper order for AFC FIR filter. Experimental results show validity of the proposed criterion. PMID:23367105

  7. Performance analysis on wideband-interference cancellation based on detailed hardware design

    NASA Astrophysics Data System (ADS)

    Mohamed, Jama

    Use of a stretch waveform in a jamming environment with closely spaced objects such as surface vessels or fighter aircraft is presented. Adaptive cancellation in the sub-banding architecture improves the system cancellation ratio on large sub-array digital receiver systems. Detailed hardware models that capture key system requirements are described. Key model components are system aperture, receive chain with beamforming and digital data processing elements. The model takes error levels at array elements (e.g., quantization and beam pointing), digital receiver (e.g., amplitude and phase errors, time-delays, and aperture dispersions). System performance is evaluated via high-fidelity models and is characterized by the computing system's cancellation ratio.

  8. Airport noise

    NASA Technical Reports Server (NTRS)

    Pendley, R. E.

    1982-01-01

    The problem of airport noise at several airports and air bases is detailed. Community reactions to the noise, steps taken to reduce jet engine noise, and the effect of airport use restrictions and curfews on air transportation are discussed. The adverse effect of changes in allowable operational noise on airport safety and altenative means for reducing noise pollution are considered. Community-airport relations and public relations are discussed.

  9. Combustion noise

    NASA Technical Reports Server (NTRS)

    Strahle, W. C.

    1977-01-01

    A review of the subject of combustion generated noise is presented. Combustion noise is an important noise source in industrial furnaces and process heaters, turbopropulsion and gas turbine systems, flaring operations, Diesel engines, and rocket engines. The state-of-the-art in combustion noise importance, understanding, prediction and scaling is presented for these systems. The fundamentals and available theories of combustion noise are given. Controversies in the field are discussed and recommendations for future research are made.

  10. Noise considerations for remote detection of life signs with microwave Doppler radar.

    PubMed

    Nguyen, Dung; Yamada, Shuhei; Park, Byung-Kwon; Lubecke, Victor; Boric-Lubecke, Olga; Host-Madsen, Anders

    2007-01-01

    This paper describes and quantifies three main sources of baseband noise affecting physiological signals in a direct conversion microwave Doppler radar for life signs detection. They are thermal noise, residual phase noise, and Flicker noise. In order to increase the SNR of physiological signals at baseband, the noise floor, in which the Flicker noise is the most dominant factor, needs to be minimized. This paper shows that with the consideration of the noise factor in our Doppler radar, Flicker noise canceling techniques may drastically reduce the power requirement for heart rate signal detection by as much as a factor of 100.

  11. Evaluation of a portable two-microphone adaptive beamforming speech processor with cochlear implant patients.

    PubMed

    van Hoesel, R J; Clark, G M

    1995-04-01

    A two-microphone noise reduction technique was tested with four cochlear implant patients. The noise reduction technique, known as adaptive beamforming (ABF), used signals from only two microphones--one behind each ear--to attenuate sounds not arriving from the direction directly in front of the patient. The algorithm was implemented in a portable digital signal processor, and was compared with a strategy in which the two microphone signals were simply added together (two-microphone broadside strategy). Tests with the four patients were conducted in a soundproof booth with target speech arriving from in front of the patient and multitalker babble noise arriving at 90 deg to the left. Results at 0-dB signal-to-noise level (S/N) showed large improvements in speech intelligibility for all patients, when compared to the two-microphone broadside strategy. Precautions were taken to avoid cancellation of the target speech, and, accordingly, subjective tests showed no deterioration in performance for the adaptive beamformer in quiet. Physical measurement of the directional characteristics of the ABF was made with the microphones placed behind the ears of a KEMAR manikin and in the same acoustic environment as used with the patients. Results showed directional gain of approximately 10 dB when the angle of incidence for interfering noise was shifted more than 20 to 30 deg from directly in front of or behind the manikin.(ABSTRACT TRUNCATED AT 250 WORDS)

  12. A fast, robust algorithm for power line interference cancellation in neural recording

    NASA Astrophysics Data System (ADS)

    Keshtkaran, Mohammad Reza; Yang, Zhi

    2014-04-01

    Objective. Power line interference may severely corrupt neural recordings at 50/60 Hz and harmonic frequencies. The interference is usually non-stationary and can vary in frequency, amplitude and phase. To retrieve the gamma-band oscillations at the contaminated frequencies, it is desired to remove the interference without compromising the actual neural signals at the interference frequency bands. In this paper, we present a robust and computationally efficient algorithm for removing power line interference from neural recordings. Approach. The algorithm includes four steps. First, an adaptive notch filter is used to estimate the fundamental frequency of the interference. Subsequently, based on the estimated frequency, harmonics are generated by using discrete-time oscillators, and then the amplitude and phase of each harmonic are estimated by using a modified recursive least squares algorithm. Finally, the estimated interference is subtracted from the recorded data. Main results. The algorithm does not require any reference signal, and can track the frequency, phase and amplitude of each harmonic. When benchmarked with other popular approaches, our algorithm performs better in terms of noise immunity, convergence speed and output signal-to-noise ratio (SNR). While minimally affecting the signal bands of interest, the algorithm consistently yields fast convergence (<100 ms) and substantial interference rejection (output SNR >30 dB) in different conditions of interference strengths (input SNR from -30 to 30 dB), power line frequencies (45-65 Hz) and phase and amplitude drifts. In addition, the algorithm features a straightforward parameter adjustment since the parameters are independent of the input SNR, input signal power and the sampling rate. A hardware prototype was fabricated in a 65 nm CMOS process and tested. Software implementation of the algorithm has been made available for open access at https://github.com/mrezak/removePLI. Significance. The proposed

  13. Study Of Adaptive-Array Signal Processing

    NASA Technical Reports Server (NTRS)

    Satorius, Edgar H.; Griffiths, Lloyd

    1990-01-01

    Report describes study of adaptive signal-processing techniques for suppression of mutual satellite interference in mobile (on ground)/satellite communication system. Presents analyses and numerical simulations of performances of two approaches to signal processing for suppression of interference. One approach, known as "adaptive side lobe canceling", second called "adaptive temporal processing".

  14. Interference cancellation in RF signals using adaptive array techniques

    NASA Astrophysics Data System (ADS)

    Brown, Mark E.

    1990-12-01

    This study investigated the effectiveness of the least means squared (LMS) algorithm against various types of common jammers. The LMS algorithm was implemented using the block oriented systems simulator (BOSS). The LMS algorithm was inserted at the output of a two element antenna array. The array was configured so as to have one-half wavelength spacing. A quadrature hybrid signal structure was used. The array was then tested against a barrage and sweep jammer. The barrage jammer testing consisted of varying each of the three available jammer parameters: power, frequency, and angle of arrival individually. The sweep jammer testing consisted of varying each of the three available jammer parameters; power, sweep frequency and angle of arrival individually. The results of the simulation showed the LMS algorithm in combination with the quadrature hybrid was very effective against both the barrage and sweep jammers. It provided a 55 dB null in the barrage jammer cases and a 50 dB null in the sweep jammer case.

  15. Improved CDMA Performance Using Parallel Interference Cancellation

    NASA Technical Reports Server (NTRS)

    Simon, Marvin; Divsalar, Dariush

    1995-01-01

    This report considers a general parallel interference cancellation scheme that significantly reduces the degradation effect of user interference but with a lesser implementation complexity than the maximum-likelihood technique. The scheme operates on the fact that parallel processing simultaneously removes from each user the interference produced by the remaining users accessing the channel in an amount proportional to their reliability. The parallel processing can be done in multiple stages. The proposed scheme uses tentative decision devices with different optimum thresholds at the multiple stages to produce the most reliably received data for generation and cancellation of user interference. The 1-stage interference cancellation is analyzed for three types of tentative decision devices, namely, hard, null zone, and soft decision, and two types of user power distribution, namely, equal and unequal powers. Simulation results are given for a multitude of different situations, in particular, those cases for which the analysis is too complex.

  16. Active control of aircraft engine inlet noise using compact sound sources and distributed error sensors

    NASA Technical Reports Server (NTRS)

    Burdisso, Ricardo (Inventor); Fuller, Chris R. (Inventor); O'Brien, Walter F. (Inventor); Thomas, Russell H. (Inventor); Dungan, Mary E. (Inventor)

    1996-01-01

    An active noise control system using a compact sound source is effective to reduce aircraft engine duct noise. The fan noise from a turbofan engine is controlled using an adaptive filtered-x LMS algorithm. Single multi channel control systems are used to control the fan blade passage frequency (BPF) tone and the BPF tone and the first harmonic of the BPF tone for a plane wave excitation. A multi channel control system is used to control any spinning mode. The multi channel control system to control both fan tones and a high pressure compressor BPF tone simultaneously. In order to make active control of turbofan inlet noise a viable technology, a compact sound source is employed to generate the control field. This control field sound source consists of an array of identical thin, cylindrically curved panels with an inner radius of curvature corresponding to that of the engine inlet. These panels are flush mounted inside the inlet duct and sealed on all edges to prevent leakage around the panel and to minimize the aerodynamic losses created by the addition of the panels. Each panel is driven by one or more piezoelectric force transducers mounted on the surface of the panel. The response of the panel to excitation is maximized when it is driven at its resonance; therefore, the panel is designed such that its fundamental frequency is near the tone to be canceled, typically 2000-4000 Hz.

  17. Active control of aircraft engine inlet noise using compact sound sources and distributed error sensors

    NASA Technical Reports Server (NTRS)

    Burdisso, Ricardo (Inventor); Fuller, Chris R. (Inventor); O'Brien, Walter F. (Inventor); Thomas, Russell H. (Inventor); Dungan, Mary E. (Inventor)

    1994-01-01

    An active noise control system using a compact sound source is effective to reduce aircraft engine duct noise. The fan noise from a turbofan engine is controlled using an adaptive filtered-x LMS algorithm. Single multi channel control systems are used to control the fan blade passage frequency (BPF) tone and the BPF tone and the first harmonic of the BPF tone for a plane wave excitation. A multi channel control system is used to control any spinning mode. The multi channel control system to control both fan tones and a high pressure compressor BPF tone simultaneously. In order to make active control of turbofan inlet noise a viable technology, a compact sound source is employed to generate the control field. This control field sound source consists of an array of identical thin, cylindrically curved panels with an inner radius of curvature corresponding to that of the engine inlet. These panels are flush mounted inside the inlet duct and sealed on all edges to prevent leakage around the panel and to minimize the aerodynamic losses created by the addition of the panels. Each panel is driven by one or more piezoelectric force transducers mounted on the surface of the panel. The response of the panel to excitation is maximized when it is driven at its resonance; therefore, the panel is designed such that its fundamental frequency is near the tone to be canceled, typically 2000-4000 Hz.

  18. CancellationTools: All-in-one software for administration and analysis of cancellation tasks.

    PubMed

    Dalmaijer, Edwin S; Van der Stigchel, Stefan; Nijboer, Tanja C W; Cornelissen, Tim H W; Husain, Masud

    2015-12-01

    In a cancellation task, a participant is required to search for and cross out ("cancel") targets, which are usually embedded among distractor stimuli. The number of cancelled targets and their location can be used to diagnose the neglect syndrome after stroke. In addition, the organization of search provides a potentially useful way to measure executive control over multitarget search. Although many useful cancellation measures have been introduced, most fail to make their way into research studies and clinical practice due to the practical difficulty of acquiring such parameters from traditional pen-and-paper measures. Here we present new, open-source software that is freely available to all. It allows researchers and clinicians to flexibly administer computerized cancellation tasks using stimuli of their choice, and to directly analyze the data in a convenient manner. The automated analysis suite provides output that includes almost all of the currently existing measures, as well as several new ones introduced here. All tasks can be performed using either a computer mouse or a touchscreen as an input device, and an online version of the task runtime is available for tablet devices. A summary of the results is produced in a single A4-sized PDF document, including high quality data visualizations. For research purposes, batch analysis of large datasets is possible. In sum, CancellationTools allows users to employ a flexible, computerized cancellation task, which provides extensive benefits and ease of use.

  19. Tissue-level remodeling simulations of cancellous bone capture effects of in vivo loading in a rabbit model.

    PubMed

    Morgan, Timothy G; Bostrom, Mathias P G; van der Meulen, Marjolein C H

    2015-03-18

    The adaptation of cancellous bone to mechanical stimuli occurs throughout normal skeletal growth and aging, as well as in response to surgery, disease and device implantation. Previously we developed an in vivo cancellous loading model in the distal lateral femur of the rabbit. In response to daily in vivo loading for four weeks, bone mass increased, trabeculae thickened and the apparent modulus of the underlying cancellous bone increased. Here, we simulated our prior in vivo rabbit loading experiment using a cell-based tissue remodeling algorithm (Mullender et al., 1994) and compared the results to the in vivo experimental data published previously. Cancellous bone tissue was added or removed from the surface of trabeculae in regions of high and low mechanical stimulus, respectively. To examine the effect of material properties on mechanically regulated adaptation, we implemented both a homogeneous material model and a model where the relative density of tissue was lower for new and surface bone tissue compared to interior tissue. The simulations captured the changes in histomorphometric parameters and mechanical properties measured in the in vivo experiment illustrating the ability of computational simulations to predict the effect of mechanically regulated adaptation on cancellous bone histomorphometry and apparent modulus. PMID:25579991

  20. Cloaking through cancellation of diffusive wave scattering

    NASA Astrophysics Data System (ADS)

    Farhat, M.; Chen, P. Y.; Guenneau, S.; Bağc, H.; Salama, K. N.; Alù, A.

    2016-08-01

    A new cloaking mechanism, which makes enclosed objects invisible to diffusive photon density waves, is proposed. First, diffusive scattering from a basic core-shell geometry, which represents the cloaked structure, is studied. The conditions of scattering cancellation in a quasi-static scattering regime are derived. These allow for tailoring the diffusivity constant of the shell enclosing the object so that the fields scattered from the shell and the object cancel each other. This means that the photon flow outside the cloak behaves as if the cloaked object were not present. Diffusive light invisibility may have potential applications in hiding hot spots in infrared thermography or tissue imaging.

  1. Adaptive Array for Weak Interfering Signals: Geostationary Satellite Experiments. M.S. Thesis

    NASA Technical Reports Server (NTRS)

    Steadman, Karl

    1989-01-01

    The performance of an experimental adaptive array is evaluated using signals from an existing geostationary satellite interference environment. To do this, an earth station antenna was built to receive signals from various geostationary satellites. In these experiments the received signals have a frequency of approximately 4 GHz (C-band) and have a bandwidth of over 35 MHz. These signals are downconverted to a 69 MHz intermediate frequency in the experimental system. Using the downconverted signals, the performance of the experimental system for various signal scenarios is evaluated. In this situation, due to the inherent thermal noise, qualitative instead of quantitative test results are presented. It is shown that the experimental system can null up to two interfering signals well below the noise level. However, to avoid the cancellation of the desired signal, the use a steering vector is needed. Various methods to obtain an estimate of the steering vector are proposed.

  2. Community noise

    NASA Technical Reports Server (NTRS)

    Bragdon, C. R.

    1982-01-01

    Airport and community land use planning as they relate to airport noise reduction are discussed. Legislation, community relations, and the physiological effect of airport noise are considered. Noise at the Logan, Los Angeles, and Minneapolis/St. Paul airports is discussed.

  3. Assessing the efficacy of active noise reduction

    NASA Astrophysics Data System (ADS)

    Rylands, Julia M.

    Active noise reduction (ANR) is an electronic technique, based on reverse phase cancellation, for reducing low frequency noise reaching an operators ears. This report discussed the basic concept, its capabilities and some approaches to assessing its efficacy. The technique provides a great enhancement to hearing protection and also enhances signal detection and communications capabilities. Tests of detectibility of pure tones at frequencies ranging up to 1750 Hz using ANR systems which had maximum noise attenuation between 300 and 600 Hz and masking noise typical of the SeaKing helicopter showed that improvements in detection performance extend up to 1000 Hz. ANR systems also offer improved speech intelligibility in high noise environments by reducing the upward spread of masking and adding speech pre-emphasis.

  4. 78 FR 73587 - Taxpayer Advocacy Panel; Meeting Cancellation.

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-06

    ... Internal Revenue Service Taxpayer Advocacy Panel; Meeting Cancellation. AGENCY: Internal Revenue Service... cancellation of the open meeting of the Taxpayer Advocacy Panel Taxpayer Communications Project Committee..., Acting Director, Taxpayer Advocacy Panel. BILLING CODE 4830-01-P...

  5. 37 CFR 2.111 - Filing petition for cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... cancellation. (a) A cancellation proceeding is commenced by filing in the Office a timely petition for... representative, as specified in § 11.14(b) of this chapter. Electronic signatures pursuant to § 2.193(c)...

  6. Measurement of drag and its cancellation

    NASA Astrophysics Data System (ADS)

    DeBra, D. B.; Conklin, J. W.

    2011-05-01

    The design of drag cancellation missions of the future will take advantage of the technology experience of the past. The importance of data for modeling of the atmosphere led to at least six types of measurement: (a) balloon flights, (b) missile-launched falling spheres, (c) the 'cannonball' satellites of Ken Champion with accelerometers for low-altitude drag measurement (late 1960s and early 1970s), (d) the Agena flight of LOGACS (1967), a Bell MESA accelerometer mounted on a rotating platform to spectrally shift low-frequency errors in the accelerometer, (e) a series of French low-level accelerometers (e.g. CACTUS, 1975), and (f) correction of differential accelerations for drag errors in measuring gravity gradient on a pair of satellites (GRACE, 2002). The independent invention of the drag-free satellite concept by Pugh and Lange (1964) to cancel external disturbance added implementation opportunities. Its first flight application was for ephemeris prediction improvement with the DISCOS flight (1972)—still the only extended free test mass flight. Then successful flights for reduced disturbance environment for science measurement with gyros on GP-B (2004) and for improved accuracy in geodesy and ocean studies (GOCE, 2009) each using accelerometer measurements to control the drag-canceling thrust. LISA, DECIGO, BBO and other gravity wave-measuring satellite systems will push the cancellation of drag to new levels.

  7. 36 CFR 223.116 - Cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Cancellation. 223.116 Section 223.116 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL PRODUCTS...

  8. Database Cancellation: The "Hows" and "Whys"

    ERIC Educational Resources Information Center

    Shapiro, Steven

    2012-01-01

    Database cancellation is one of the most difficult tasks performed by a librarian. This may seem counter-intuitive but, psychologically, it is certainly true. When a librarian or a team of librarians has invested a great deal of time doing research, talking to potential users, and conducting trials before deciding to subscribe to a database, they…

  9. 43 CFR 3108.3 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... OF THE INTERIOR MINERALS MANAGEMENT (3000) OIL AND GAS LEASING Relinquishment, Termination... law, the regulations issued thereunder, or the lease, the lease may be canceled by the Secretary, if the leasehold does not contain a well capable of production of oil or gas in paying quantities, or...

  10. Heineman Prize Lecture: Anomaly Cancellation: A Retrospective

    NASA Astrophysics Data System (ADS)

    Schwarz, John

    2002-04-01

    The mechanism by which gauge and gravitational anomalies cancel in certain string theories is reviewed. A few new tricks are introduced to make the derivation a little simpler, and the string-theoretic interpretation a little clearer, than in the original 1984 work.

  11. Experimental Demonstration of Underwater Acoustic Scattering Cancellation

    PubMed Central

    Rohde, Charles A.; Martin, Theodore P.; Guild, Matthew D.; Layman, Christopher N.; Naify, Christina J.; Nicholas, Michael; Thangawng, Abel L.; Calvo, David C.; Orris, Gregory J.

    2015-01-01

    We explore an acoustic scattering cancellation shell for buoyant hollow cylinders submersed in a water background. A thin, low-shear, elastic coating is used to cancel the monopole scattering from an air-filled, neutrally buoyant steel shell for all frequencies where the wavelength is larger than the object diameter. By design, the uncoated shell also has an effective density close to the aqueous background, independently canceling its dipole scattering. Due to the significantly reduced monopole and dipole scattering, the compliant coating results in a hollow cylindrical inclusion that is simultaneously impedance and sound speed matched to the water background. We demonstrate the proposed cancellation method with a specific case, using an array of hollow steel cylinders coated with thin silicone rubber shells. These experimental results are matched to finite element modeling predictions, confirming the scattering reduction. Additional calculations explore the optimization of the silicone coating properties. Using this approach, it is found that scattering cross-sections can be reduced by 20 dB for all wavelengths up to k0a = 0.85. PMID:26282067

  12. 36 CFR 223.116 - Cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Cancellation. 223.116 Section 223.116 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL PRODUCTS...

  13. 36 CFR 223.116 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Cancellation. 223.116 Section 223.116 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL PRODUCTS...

  14. 36 CFR 223.116 - Cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Cancellation. 223.116 Section 223.116 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL PRODUCTS...

  15. 25 CFR 213.40 - Cancellations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the opinion... or of the applicable regulations, or if mining operations are conducted wastefully and without regard to good mining practice, the Secretary of the Interior shall have the right at any time after 30...

  16. 25 CFR 213.40 - Cancellations.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... FIVE CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.40 Cancellations. (a) When, in the opinion... or of the applicable regulations, or if mining operations are conducted wastefully and without regard to good mining practice, the Secretary of the Interior shall have the right at any time after 30...

  17. 44 CFR 206.376 - Loan cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 44 Emergency Management and Assistance 1 2013-10-01 2013-10-01 false Loan cancellation. 206.376 Section 206.376 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF... as a liability is incurred, regardless of the timing of related cash flows. (c) Revenue...

  18. 7 CFR 1956.130 - Cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... of acceleration by written notice prior to the date of application. (b) Without application by debtor... bankruptcy shall be cancelled by the use of Form FmHA or its successor agency under Public Law 103-354 1956-1... its successor agency under Public Law 103-354 1956-1 will document: (i) The sources of...

  19. 7 CFR 1956.130 - Cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... of acceleration by written notice prior to the date of application. (b) Without application by debtor... bankruptcy shall be cancelled by the use of Form FmHA or its successor agency under Public Law 103-354 1956-1... its successor agency under Public Law 103-354 1956-1 will document: (i) The sources of...

  20. 7 CFR 1956.70 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... the note or other instrument, or because of acceleration by written notice prior to the date of application. Debts due the FmHA or its successor agency under Public Law 103-354 may be canceled upon... administrator, subject to the following conditions: (1) The FmHA or its successor agency under Public Law...

  1. 7 CFR 1956.70 - Cancellation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... the note or other instrument, or because of acceleration by written notice prior to the date of application. Debts due the FmHA or its successor agency under Public Law 103-354 may be canceled upon... administrator, subject to the following conditions: (1) The FmHA or its successor agency under Public Law...

  2. 7 CFR 1956.130 - Cancellation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... of acceleration by written notice prior to the date of application. (b) Without application by debtor... bankruptcy shall be cancelled by the use of Form FmHA or its successor agency under Public Law 103-354 1956-1... its successor agency under Public Law 103-354 1956-1 will document: (i) The sources of...

  3. 7 CFR 1956.130 - Cancellation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... of acceleration by written notice prior to the date of application. (b) Without application by debtor... bankruptcy shall be cancelled by the use of Form FmHA or its successor agency under Public Law 103-354 1956-1... its successor agency under Public Law 103-354 1956-1 will document: (i) The sources of...

  4. 7 CFR 1956.70 - Cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... the note or other instrument, or because of acceleration by written notice prior to the date of application. Debts due the FmHA or its successor agency under Public Law 103-354 may be canceled upon... administrator, subject to the following conditions: (1) The FmHA or its successor agency under Public Law...

  5. 7 CFR 1956.70 - Cancellation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... the note or other instrument, or because of acceleration by written notice prior to the date of application. Debts due the FmHA or its successor agency under Public Law 103-354 may be canceled upon... administrator, subject to the following conditions: (1) The FmHA or its successor agency under Public Law...

  6. Method for Canceling Ionospheric Doppler Effect

    NASA Technical Reports Server (NTRS)

    Vessot, R. F. C.

    1982-01-01

    Unified transponder system with hydrogen-maser oscillators at both stations can compensate for both motional and ionospheric components of Doppler shift. Appropriate choices of frequency shift in output of mixer m3. System exploits proportionality between dispersive component of frequency shift and reciprocal of frequency to achieve cancellation of dispersive component at output.

  7. Rotor noise

    NASA Astrophysics Data System (ADS)

    Schmitz, F. H.

    1991-08-01

    The physical characteristics and sources of rotorcraft noise as they exist today are presented. Emphasis is on helicopter-like vehicles, that is, on rotorcraft in nonaxial flight. The mechanisms of rotor noise are reviewed in a simple physical manner for the most dominant sources of rotorcraft noise. With simple models, the characteristic time- and frequency-domain features of these noise sources are presented for idealized cases. Full-scale data on several rotorcraft are then reviewed to allow for the easy identification of the type and extent of the radiating noise. Methods and limitations of using scaled models to test for several noise sources are subsequently presented. Theoretical prediction methods are then discussed and compared with experimental data taken under very controlled conditions. Finally, some promising noise reduction technology is reviewed.

  8. Rotor noise

    NASA Technical Reports Server (NTRS)

    Schmitz, F. H.

    1991-01-01

    The physical characteristics and sources of rotorcraft noise as they exist today are presented. Emphasis is on helicopter-like vehicles, that is, on rotorcraft in nonaxial flight. The mechanisms of rotor noise are reviewed in a simple physical manner for the most dominant sources of rotorcraft noise. With simple models, the characteristic time- and frequency-domain features of these noise sources are presented for idealized cases. Full-scale data on several rotorcraft are then reviewed to allow for the easy identification of the type and extent of the radiating noise. Methods and limitations of using scaled models to test for several noise sources are subsequently presented. Theoretical prediction methods are then discussed and compared with experimental data taken under very controlled conditions. Finally, some promising noise reduction technology is reviewed.

  9. Non-linear, adaptive array processing for acoustic interference suppression.

    PubMed

    Hoppe, Elizabeth; Roan, Michael

    2009-06-01

    A method is introduced where blind source separation of acoustical sources is combined with spatial processing to remove non-Gaussian, broadband interferers from space-time displays such as bearing track recorder displays. This differs from most standard techniques such as generalized sidelobe cancellers in that the separation of signals is not done spatially. The algorithm performance is compared to adaptive beamforming techniques such as minimum variance distortionless response beamforming. Simulations and experiments using two acoustic sources were used to verify the performance of the algorithm. Simulations were also used to determine the effectiveness of the algorithm under various signal to interference, signal to noise, and array geometry conditions. A voice activity detection algorithm was used to benchmark the performance of the source isolation.

  10. Decentralized adaptive control designs and microstrip antennas for smart structures

    NASA Astrophysics Data System (ADS)

    Khorrami, Farshad; Jain, Sandeep; Das, Nirod K.

    1996-05-01

    Smart structures lend themselves naturally to a decentralized control design framework, especially with adaptation mechanisms. The main reason being that it is highly undesirable to connect all the sensors and actuators in a large structure to a central processor. It is rather desirable to have local decision-making at each smart patch. Furthermore, this local controllers should be easily `expandable' to `contractible.' This corresponds to the fact that addition/deletion of several smart patches should not require a total redesign of the control system. The decentralized control strategies advocated in this paper are of expandable/contractible type. On another front, we are considering utilization of micro-strip antennas for power transfer to and from smart structures. We have made preliminary contributions in this direction and further developments are underway. These approaches are being pursued for active vibration damping and noise cancellation via piezoelectric ceramics although the methodology is general enough to be applicable to other type of active structures.

  11. 12 CFR 209.3 - Cancellation of Reserve Bank stock.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 2 2011-01-01 2011-01-01 false Cancellation of Reserve Bank stock. 209.3 Section 209.3 Banks and Banking FEDERAL RESERVE SYSTEM BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM ISSUE AND CANCELLATION OF FEDERAL RESERVE BANK CAPITAL STOCK (REGULATION I) § 209.3 Cancellation...

  12. 46 CFR 308.511 - Cancellation of Open Cargo Policy.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Cancellation of Open Cargo Policy. 308.511 Section 308... INSURANCE War Risk Cargo Insurance Ii-Open Policy War Risk Cargo Insurance § 308.511 Cancellation of Open Cargo Policy. An assured may cancel an Open Cargo Policy by delivering to the underwriting agent,...

  13. 25 CFR 273.62 - Cancelling a contract for cause.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 1 2011-04-01 2011-04-01 false Cancelling a contract for cause. 273.62 Section 273.62....62 Cancelling a contract for cause. (a) Any contract entered into under this part may be cancelled for cause when the contractor fails to perform the work called for under the contract or fails...

  14. 25 CFR 273.62 - Cancelling a contract for cause.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Cancelling a contract for cause. 273.62 Section 273.62....62 Cancelling a contract for cause. (a) Any contract entered into under this part may be cancelled for cause when the contractor fails to perform the work called for under the contract or fails...

  15. 25 CFR 273.62 - Cancelling a contract for cause.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 1 2013-04-01 2013-04-01 false Cancelling a contract for cause. 273.62 Section 273.62....62 Cancelling a contract for cause. (a) Any contract entered into under this part may be cancelled for cause when the contractor fails to perform the work called for under the contract or fails...

  16. 25 CFR 273.62 - Cancelling a contract for cause.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 1 2012-04-01 2011-04-01 true Cancelling a contract for cause. 273.62 Section 273.62....62 Cancelling a contract for cause. (a) Any contract entered into under this part may be cancelled for cause when the contractor fails to perform the work called for under the contract or fails...

  17. 25 CFR 273.62 - Cancelling a contract for cause.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 1 2014-04-01 2014-04-01 false Cancelling a contract for cause. 273.62 Section 273.62....62 Cancelling a contract for cause. (a) Any contract entered into under this part may be cancelled for cause when the contractor fails to perform the work called for under the contract or fails...

  18. 14 CFR 297.25 - Cancellation or conditioning of registration.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Cancellation or conditioning of... § 297.25 Cancellation or conditioning of registration. The registration of a foreign indirect air carrier may be canceled or subjected to additional terms, conditions or limitations if: (a) It files...

  19. 26 CFR 301.6804-1 - Attachment and cancellation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 26 Internal Revenue 18 2010-04-01 2010-04-01 false Attachment and cancellation. 301.6804-1 Section 301.6804-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) PROCEDURE... Attachment and cancellation. For provisions relating to the attachment and cancellation of specific...

  20. 12 CFR 209.3 - Cancellation of Reserve Bank stock.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 2 2012-01-01 2012-01-01 false Cancellation of Reserve Bank stock. 209.3 Section 209.3 Banks and Banking FEDERAL RESERVE SYSTEM BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM ISSUE AND CANCELLATION OF FEDERAL RESERVE BANK CAPITAL STOCK (REGULATION I) § 209.3 Cancellation...

  1. 48 CFR 52.217-2 - Cancellation Under Multiyear Contracts.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... canceled work; or (4) For service contracts, the remaining useful commercial life of facilities. Useful commercial life means the commercial utility of the facilities rather than their physical life with due... clause: Cancellation Under Multiyear Contracts (OCT 1997) (a) Cancellation, as used in this clause,...

  2. 48 CFR 52.217-2 - Cancellation Under Multiyear Contracts.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... canceled work; or (4) For service contracts, the remaining useful commercial life of facilities. Useful commercial life means the commercial utility of the facilities rather than their physical life with due... clause: Cancellation Under Multiyear Contracts (OCT 1997) (a) Cancellation, as used in this clause,...

  3. 5 CFR 870.906 - Cancellation of insurance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATIONS (CONTINUED) FEDERAL EMPLOYEES' GROUP LIFE INSURANCE PROGRAM Assignments of Life Insurance § 870.906 Cancellation of insurance. (a) The right to cancel (or reduce) insurance transfers to the assignee... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Cancellation of insurance....

  4. 30 CFR 250.181 - When may the Secretary cancel my lease and when am I compensated for cancellation?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... cancellation? If the Secretary cancels your lease under this part or under 30 CFR part 256, you are entitled to... OPERATIONS IN THE OUTER CONTINENTAL SHELF General Primary Lease Requirements, Lease Term Extensions,...

  5. Influence of the occlusion effect over the prediction-error feedback cancellation system in hearing aids.

    PubMed

    Coelho Borges, Renata; Holsbach Costa, Marcio

    2015-08-01

    This work presents a theoretical analysis of the prediction-error method-based adaptive feedback canceller in hearing aid applications. The studied scene takes into account the occlusion effect caused by the partial or complete closing of the ventilation opening. Such a situation may occur in high gain applications to avoid undesired whistling. Deterministic recursive equations and steady-state conditions were derived for the mean weight behaviour of the predictor and the adaptive filter. The expected theoretical predictions were compared to Monte Carlo simulations, showing very accurate agreement. The simulation results suggest the steady-state performance of this feedback canceller is not affected by the occlusion effect, however the occlusion is still perceived, being annoying to the user. PMID:26736855

  6. The across frequency independence of equalization of interaural time delay in the equalization-cancellation model of binaural unmasking

    NASA Astrophysics Data System (ADS)

    Akeroyd, Michael A.

    2004-08-01

    The equalization stage in the equalization-cancellation model of binaural unmasking compensates for the interaural time delay (ITD) of a masking noise by introducing an opposite, internal delay [N. I. Durlach, in Foundations of Modern Auditory Theory, Vol. II., edited by J. V. Tobias (Academic, New York, 1972)]. Culling and Summerfield [J. Acoust. Soc. Am. 98, 785-797 (1995)] developed a multi-channel version of this model in which equalization was ``free'' to use the optimal delay in each channel. Two experiments were conducted to test if equalization was indeed free or if it was ``restricted'' to the same delay in all channels. One experiment measured binaural detection thresholds, using an adaptive procedure, for 1-, 5-, or 17-component tones against a broadband masking noise, in three binaural configurations (N0S180, N180S0, and N90S270). The thresholds for the 1-component stimuli were used to normalize the levels of each of the 5- and 17-component stimuli so that they were equally detectable. If equalization was restricted, then, for the 5- and 17-component stimuli, the N90S270 and N180S0 configurations would yield a greater threshold than the N0S180 configurations. No such difference was found. A subsequent experiment measured binaural detection thresholds, via psychometric functions, for a 2-component complex tone in the same three binaural configurations. Again, no differential effect of configuration was observed. An analytic model of the detection of a complex tone showed that the results were more consistent with free equalization than restricted equalization, although the size of the differences was found to depend on the shape of the psychometric function for detection.

  7. Development of high-speed, low-noise NIR HgCdTe avalanche photodiode arrays for adaptive optics and interferometry

    NASA Astrophysics Data System (ADS)

    Finger, Gert; Baker, Ian; Dorn, Reinhold; Eschbaumer, Siegfried; Ives, Derek; Mehrgan, Leander; Meyer, Manfred; Stegmeier, Jörg

    2010-07-01

    The most promising way to overcome the CMOS noise barrier of infrared AO sensors is the amplification of the photoelectron signal directly at the point of absorption inside the infrared pixel by means of the avalanche gain. HgCdTe eAPD arrays with cut off wavelengths of λc ~2.64 μm produced by SELEX-Galileo have been evaluated at ESO. The arrays were hybridized to an existing non-optimized ROIC developed for laser gated imaging which has a format of 320×256 pixels and four parallel video outputs. The avalanche gain makes it possible to reduce the read noise to < 7 e rms. The dark current requirements of IR wavefront sensing are also met.

  8. Adaptive-passive control of noise radiation of gear-box systems using a pair of shunted piezo-based rotating inertial actuators

    NASA Astrophysics Data System (ADS)

    Zhao, G.; Alujevic, N.; Depraetere, B.; Pinte, Gregory; Sas, P.

    2015-04-01

    In this paper, two Piezo-Based Rotating Inertial Actuators (PBRIAs) are considered for the suppression of the structureborne noise radiated from rotating machinery. Each inertial actuator comprises a piezoelectric stack element shunted with the Antoniou's gyrator circuit. This type of electrical circuit can be used to emulate a variable inductance. By varying the shunt inductance it is possible to realize two tuneable vibration neutralizers in order to suppress single frequency vibrations of a slowly rotating shaft. As a consequence, reductions in the sound radiated from the machine housing can be also achieved. First a theoretical study is performed using a simplified lumped parameter model of the system at hand. The simplified model consists of a rotating shaft and two perpendicularly mounted shunted PBRIAs. Secondly, the shunted PBRIA is tested on an experimental test bed comprising a rotating shaft mounted in a frame. The noise is radiated by a plate that is attached to the frame. The experimental results show that a reduction of 11 dB on the disturbance force transmitted from the rotating shaft through the bearing to the housing can be achieved. This also generates a reduction of 9 dB for the plate vibration and the radiated noise.

  9. Quantum Noise in Laser Diodes

    NASA Technical Reports Server (NTRS)

    Giacobino, E.; Marin, F.; Bramati, A.; Jost, V.; Poizat, J. Ph.; Roch, J.-F.; Grangier, P.; Zhang, T.-C.

    1996-01-01

    We have investigated the intensity noise of single mode laser diodes, either free-running or using different types of line narrowing techniques at room temperature. We have measured an intensity squeezing of 1.2 dB with grating-extended cavity lasers and 1.4 dB with injection locked lasers (respectively 1.6 dB and 2.3 dB inferred at the laser output). We have observed that the intensity noise of a free-running nominally single mode laser diode results from a cancellation effect between large anti-correlated fluctuations of the main mode and of weak longitudinal side modes. Reducing the side modes by line narrowing techniques results in intensity squeezing.

  10. Airframe noise

    NASA Astrophysics Data System (ADS)

    Crighton, David G.

    1991-08-01

    Current understanding of airframe noise was reviewed as represented by experiment at model and full scale, by theoretical modeling, and by empirical correlation models. The principal component sources are associated with the trailing edges of wing and tail, deflected trailing edge flaps, flap side edges, leading edge flaps or slats, undercarriage gear elements, gear wheel wells, fuselage and wing boundary layers, and panel vibration, together with many minor protrusions like radio antennas and air conditioning intakes which may contribute significantly to perceived noise. There are also possibilities for interactions between the various mechanisms. With current engine technology, the principal airframe noise mechanisms dominate only at low frequencies, typically less than 1 kHz and often much lower, but further reduction of turbomachinery noise in particular may make airframe noise the principal element of approach noise at frequencies in the sensitive range.

  11. A Review on Successive Interference Cancellation Scheme Based on Optical CDMA Network

    NASA Astrophysics Data System (ADS)

    Alsowaidi, N.; Eltaif, T.; Mokhtar, M. R.

    2014-12-01

    Due to various desirable features of optical code division multiple access (OCDMA), it is believed this technique once developed and commercially available will be an integral part of optical access networks. Optical CDMA system suffers from a problem called multiple access interference (MAI) which limits the number of active users, it occurs when number of active users share the same carriers. The aim of this paper is to review successive interference cancellation (SIC) scheme based on optical CDMA system. The paper also reviews the system performance in presence of shot noise, thermal noise, and phase-induced intensity noise (PIIN). A comprehensive review on the mathematical model of SIC scheme using direct detection (DS) and spectral amplitude coding (SAC) were presented in this article.

  12. Interior Noise

    NASA Technical Reports Server (NTRS)

    Mixson, John S.; Wilby, John F.

    1991-01-01

    The generation and control of flight vehicle interior noise is discussed. Emphasis is placed on the mechanisms of transmission through airborne and structure-borne paths and the control of cabin noise by path modification. Techniques for identifying the relative contributions of the various source-path combinations are also discussed along with methods for the prediction of aircraft interior noise such as those based on the general modal theory and statistical energy analysis.

  13. Noise Protection

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Environmental Health Systems puts forth an increasing effort in the U.S. to develop ways of controlling noise, particularly in industrial environments due to Federal and State laws, labor union insistence and new findings relative to noise pollution impact on human health. NASA's Apollo guidance control system aided in the development of a noise protection product, SMART. The basis of all SMART products is SMART compound a liquid plastic mixture with exceptional energy/sound absorbing qualities. The basic compound was later refined for noise protection use.

  14. The Burden of Surgical Cancellations and No-Shows

    PubMed Central

    Appavu, Sivasubramanian T.; Al-Shekaili, Salim M.; Al-Sharif, Ahmed M.; Elawdy, Mohamed M.

    2016-01-01

    Objectives: The operating theatre (OT) is a vital facility that utilises a considerable portion of the hospital’s budget; thus proper OT utilisation is essential. Surgical cancellation is a leading cause of OT underutilisation. This study aimed to report the rate and reasons for surgical cancellations and no-shows in a large regional hospital in Oman. Methods: This study took place as part of a retrospective quality management project at the Ibri Regional Hospital, Ibri, Oman. All elective surgical procedures scheduled between January and December 2014 were included. Cancelled procedures were reviewed to determine the reasons for cancellation. Results: A total of 4,814 elective procedures were scheduled during the study period; of these, 1,235 (26%) were cancelled. Patient no-shows were the most prevalent reason for surgical cancellation (63%), followed by surgical reasons (17%); in contrast, OT-associated reasons were responsible for only 2% of cancellations. According to speciality, general surgery had the highest percentage of total cancellations (65%), while ear, nose and throat had the highest rate of surgical cancellations among their scheduled cases (42%). Conclusion: Ibri Regional Hospital had a higher surgical cancellation rate due to no-shows than those reported in the literature. Regular audits, quality management projects and the appointment of a dedicated procedure booking coordinator may enhance proper utilisation of the OT, potentially saving funds, conserving resources and alleviating the burden of cancellations.

  15. The Burden of Surgical Cancellations and No-Shows

    PubMed Central

    Appavu, Sivasubramanian T.; Al-Shekaili, Salim M.; Al-Sharif, Ahmed M.; Elawdy, Mohamed M.

    2016-01-01

    Objectives: The operating theatre (OT) is a vital facility that utilises a considerable portion of the hospital’s budget; thus proper OT utilisation is essential. Surgical cancellation is a leading cause of OT underutilisation. This study aimed to report the rate and reasons for surgical cancellations and no-shows in a large regional hospital in Oman. Methods: This study took place as part of a retrospective quality management project at the Ibri Regional Hospital, Ibri, Oman. All elective surgical procedures scheduled between January and December 2014 were included. Cancelled procedures were reviewed to determine the reasons for cancellation. Results: A total of 4,814 elective procedures were scheduled during the study period; of these, 1,235 (26%) were cancelled. Patient no-shows were the most prevalent reason for surgical cancellation (63%), followed by surgical reasons (17%); in contrast, OT-associated reasons were responsible for only 2% of cancellations. According to speciality, general surgery had the highest percentage of total cancellations (65%), while ear, nose and throat had the highest rate of surgical cancellations among their scheduled cases (42%). Conclusion: Ibri Regional Hospital had a higher surgical cancellation rate due to no-shows than those reported in the literature. Regular audits, quality management projects and the appointment of a dedicated procedure booking coordinator may enhance proper utilisation of the OT, potentially saving funds, conserving resources and alleviating the burden of cancellations. PMID:27606108

  16. Nonlinear adaptive wavelet analysis of electrocardiogram signals

    NASA Astrophysics Data System (ADS)

    Yang, H.; Bukkapatnam, S. T.; Komanduri, R.

    2007-08-01

    Wavelet representation can provide an effective time-frequency analysis for nonstationary signals, such as the electrocardiogram (EKG) signals, which contain both steady and transient parts. In recent years, wavelet representation has been emerging as a powerful time-frequency tool for the analysis and measurement of EKG signals. The EKG signals contain recurring, near-periodic patterns of P , QRS , T , and U waveforms, each of which can have multiple manifestations. Identification and extraction of a compact set of features from these patterns is critical for effective detection and diagnosis of various disorders. This paper presents an approach to extract a fiducial pattern of EKG based on the consideration of the underlying nonlinear dynamics. The pattern, in a nutshell, is a combination of eigenfunctions of the ensembles created from a Poincare section of EKG dynamics. The adaptation of wavelet functions to the fiducial pattern thus extracted yields two orders of magnitude (some 95%) more compact representation (measured in terms of Shannon signal entropy). Such a compact representation can facilitate in the extraction of features that are less sensitive to extraneous noise and other variations. The adaptive wavelet can also lead to more efficient algorithms for beat detection and QRS cancellation as well as for the extraction of multiple classical EKG signal events, such as widths of QRS complexes and QT intervals.

  17. Stationary echo canceling in velocity estimation by time-domain cross-correlation.

    PubMed

    Jensen, J A

    1993-01-01

    The application of stationary echo canceling to ultrasonic estimation of blood velocities using time-domain cross-correlation is investigated. Expressions are derived that show the influence from the echo canceler on the signals that enter the cross-correlation estimator. It is demonstrated that the filtration results in a velocity-dependent degradation of the signal-to-noise ratio. An analytic expression is given for the degradation for a realistic pulse. The probability of correct detection at low signal-to-noise ratios is influenced by signal-to-noise ratio, transducer bandwidth, center frequency, number of samples in the range gate, and number of A-lines employed in the estimation. Quantitative results calculated by a simple simulation program are given for the variation in probability from these parameters. An index reflecting the reliability of the estimate at hand can be calculated from the actual cross-correlation estimate by a simple formula and used in rejecting poor estimates or in displaying the reliability of the velocity estimated.

  18. Voice communications in the cockpit noise environment: The role of active noise reduction

    NASA Astrophysics Data System (ADS)

    Wheeler, Peter David

    The topic of voice communications in the cockpit noise environment of modern fast-jet aircraft and helicopters is addressed, and in particular, research undertaken in support of the development of a system for reducing the noise level at the operators' ear is described by acoustic cancellation within the ear defender, known as active noise reduction (ANR). The internal noise spectra of today's high performance fast-jet aircraft and military helicopters is described, and the complex interaction of acoustic noise transmission, speech, and microphone noise pick-up, which produces the total acoustic environment at the aircrews' ears, is discussed. Means of mathematically modelling the audio channel, quantifying the components identified above, and identifying areas of shortfall in performance are derived, leading to a procedure for the development of attenuation requirements, described as the communications audit. A model of the electroacoustic characteristics of the ANR ear defender assembly is presented and the sound field distribution within the ear defender/ear cavity, and its effect upon cancellation performance, is discussed. The extensive laboratory and flight testing of the ANR system that was undertaken is reviewed, paying particular attention to the measurement and analysis techniques employed in such testing. Finally, the performance characteristics of ANR are discussed and compared with the requirements previously established. Design limitations placed upon the system by the constraints of its area of application are described, and the scope for future improvements is considered.

  19. A multi-resolution filtered-x LMS algorithm based on discrete wavelet transform for active noise control

    NASA Astrophysics Data System (ADS)

    Qiu, Z.; Lee, C.-M.; Xu, Z. H.; Sui, L. N.

    2016-01-01

    We have developed a new active control algorithm based on discrete wavelet transform (DWT) for both stationary and non-stationary noise control. First, the Mallat pyramidal algorithm is introduced to implement the DWT, which can decompose the reference signal into several sub-bands with multi-resolution and provides a perfect reconstruction (PR) procedure. To reduce the extra computational complexity introduced by DWT, an efficient strategy is proposed that updates the adaptive filter coefficients in the frequency domainDeepthi B.B using a fast Fourier transform (FFT). Based on the reference noise source, a 'Haar' wavelet is employed and by decomposing the noise signal into two sub-band (3-band), the proposed DWT-FFT-based FXLMS (DWT-FFT-FXLMS) algorithm has greatly reduced complexity and a better convergence performance compared to a time domain filtered-x least mean square (TD-FXLMS) algorithm. As a result of the outstanding time-frequency characteristics of wavelet analysis, the proposed DWT-FFT-FXLMS algorithm can effectively cancel both stationary and non-stationary noise, whereas the frequency domain FXLMS (FD-FXLMS) algorithm cannot approach this point.

  20. Progressive femoral cortical and cancellous bone density loss after uncemented tapered-design stem fixation

    PubMed Central

    Nowak, Tobias E; Haeberle, Lothar; Mueller, Lars P; Kress, Alexander; Voelk, Michael; Pfander, David; Forst, Raimund; Schmidt, Rainer

    2010-01-01

    Background Aseptic implant loosening and periprosthetic bone loss are major problems after total hip arthroplasty (THA). We present an in vivo method of computed tomography (CT) assisted osteodensitometry after THA that differentiates between cortical and cancellous bone density (BD) and area around the femoral component. Method Cortical and cancellous periprosthetic femoral BD (mg CaHA/mL), area (mm2) and contact area between the prothesis and cortical bone were determined prospectively in 31 patients 10 days, 1 year, and 6 years after uncemented THA (mean age at implantation: 55 years) using CT-osteodensitometry. Results 6 years postoperatively, cancellous BD had decreased by as much as 41% and cortical BD by up to 27% at the metaphyseal portion of the femur; this decrease was progressive between the 1-year and 6-year examinations. Mild cortical hypertrophy was observed along the entire length of the diaphysis. No statistically significant changes in cortical BD were observed along the diaphysis of the stem. Interpretation Periprosthetic CT-assisted osteodensitometry has the technical ability to discriminate between cortical and cancellous bone structures with respect to strain-adapted remodeling. Continuous loss of cortical and cancellous BD at the femoral metaphysis, a homeostatic cortical strain configuration, and mild cortical hypertrophy along the diaphysis suggest a diaphyseal fixation of the implanted stem. CT-assisted osteodensitometry has the potential to become an effective instrument for quality control in THA by means of in vivo determination of periprosthetic BD, which may be a causal factor in implant loosening after THA. PMID:20180716

  1. Landslide noise.

    PubMed

    Cadman, J D; Goodman, R E

    1967-12-01

    Acoustical monitoring of real landslides has revealed the existence of subaudible noise activity prior to failure and has enabled prediction of the depth of the seat of sliding when conducted in boreholes beneath the surface. Recordings of noise generated in small slopes of moist sand, tilted to failure in laboratory tests, have been analyzed to determine the foci of discrete subaudible noise events. The noises emitted shortly before failure were plotted close to the true sliding surface observed after failure. The foci of earlier events lay either within the central portion of the sliding mass or in a region behind the failure surface. The head and toe zones were devoid of strong seismic activity. PMID:17734306

  2. The effects of PTH, loading and surgical insult on cancellous bone at the bone-implant interface in the rabbit

    PubMed Central

    Fahlgren, Anna; Yang, Xu; Ciani, Cesare; Ryan, James A.; Kelly, Natalie; Ko, Frank C.; van der Meulen, Marjolein C.H.; Bostrom, Mathias P.G.

    2014-01-01

    Enhancing the quantity and quality of cancellous bone with anabolic pharmacologic agents may lead to more successful outcomes of non-cemented joint replacements. Using a novel rabbit model of cancellous bone loading, we examined two specific questions regarding bone formation at the bone-implant interface: (1) does the administration of intermittent PTH, a potent anabolic agent, and mechanical loading individually and combined enhance the peri-implant cancellous bone volume fraction; and, (2) does surgical trauma enhance the anabolic effect of PTH on peri-implant bone volume fraction. In this model, PTH enhanced peri-implant bone volume fraction by 30% in loaded bone, while mechanical loading alone increased bone volume fraction modestly (+10%). Combined mechanical loading and PTH treatment had no synergistic effect on any cancellous parameters. However, a strong combined effect was found in bone volume fraction with combined surgery and PTH treatment (+34%) compared to intact control limbs. Adaptive changes in the cancellous bone tissue included increased ultimate stress and enhanced remodeling activity. The number of proliferative osteoblasts increased as did their expression of pro-collagen 1 and PTH receptor 1, and the number of TRAP positive osteoclasts also increased. In summary, both loading and intermittent PTH treatment enhanced peri-implant bone volume, and surgery and PTH treatment had a strong combined effect. This finding is of clinical importance since enhancing early osseointegration in the post-surgical period has numerous potential benefits. PMID:22613252

  3. Discussions on the Cancellation Effect on a Curved Orbit

    SciTech Connect

    Rui Li; Ya. S. Derbenev

    2005-05-16

    The canonical formulation and the cancellation effect for bunch dynamics under collective interaction on a curved orbit were presented in Ref. [*]. Some possible controversial representations of the cancellation effect were later addressed by Geloni et al.** In this study, we discuss all the points raised in Ref. [**] based on our canonical treatment, and show how these points can be perceived from the view point of the cancellation picture.

  4. High level white noise generator

    DOEpatents

    Borkowski, Casimer J.; Blalock, Theron V.

    1979-01-01

    A wide band, stable, random noise source with a high and well-defined output power spectral density is provided which may be used for accurate calibration of Johnson Noise Power Thermometers (JNPT) and other applications requiring a stable, wide band, well-defined noise power spectral density. The noise source is based on the fact that the open-circuit thermal noise voltage of a feedback resistor, connecting the output to the input of a special inverting amplifier, is available at the amplifier output from an equivalent low output impedance caused by the feedback mechanism. The noise power spectral density level at the noise source output is equivalent to the density of the open-circuit thermal noise or a 100 ohm resistor at a temperature of approximately 64,000 Kelvins. The noise source has an output power spectral density that is flat to within 0.1% (0.0043 db) in the frequency range of from 1 KHz to 100 KHz which brackets typical passbands of the signal-processing channels of JNPT's. Two embodiments, one of higher accuracy that is suitable for use as a standards instrument and another that is particularly adapted for ambient temperature operation, are illustrated in this application.

  5. System approach to robust acoustic echo cancellation through semi-blind source separation based on independent component analysis

    NASA Astrophysics Data System (ADS)

    Wada, Ted S.

    In this dissertation, we build a foundation for what we refer to as the system approach to signal enhancement as we focus on the acoustic echo cancellation (AEC) problem. Such a “system” perspective aims for the integration of individual components, or algorithms, into a cohesive unit for the benefit of the system as a whole to cope with real-world enhancement problems. The standard system identification approach by minimizing the mean square error (MSE) of a linear system is sensitive to distortions that greatly affect the quality of the identification result. Therefore, we begin by examining in detail the technique of using a noise-suppressing nonlinearity in the adaptive filter error feedback-loop of the LMS algorithm when there is an interference at the near end, where the source of distortion may be linear or nonlinear. We provide a thorough derivation and analysis of the error recovery nonlinearity (ERN) that “enhances” the filter estimation error prior to the adaptation to transform the corrupted error’s distribution into a desired one, or very close to it, in order to assist the linear adaptation process. We reveal important connections of the residual echo enhancement (REE) technique to other existing AEC and signal enhancement procedures, where the technique is well-founded in the information-theoretic sense and has strong ties to independent component analysis (ICA), which is the basis for blind source separation (BSS) that permits unsupervised adaptation in the presence of multiple interfering signals. Notably, the single-channel AEC problem can be viewed as a special case of semi-blind source separation (SBSS) where one of the source signals is partially known, i.e., the far-end microphone signal that generates the near-end acoustic echo. Indeed, SBSS optimized via ICA leads to the system combination of the LMS algorithm with the ERN that allows continuous and stable adaptation even during double talk. Next, we extend the system perspective

  6. A shock wave approach to the noise of supersonic propellers

    NASA Technical Reports Server (NTRS)

    Dittmar, J. H.; Rice, E. J.

    1981-01-01

    To model propeller noise expected for a turboprop aircraft, the pressure ratio across the shock at the propeller tip was calculated and compared with noise data from three propellers. At helical tip Mach numbers over 1.0, using only the tip shock wave, the model gave a fairly good prediction of the noise for a bladed propeller and for a propeller swept for aerodynamic purposes. However for another propeller, which was highly swept and designed to have noise cancellations from the inboard propeller sections, the shock strength from the tip over predicted the noise. In general the good agreement indicates that shock theory is a viable method for predicting the noise from these supersonic propellers but that the shock strengths from all of the blade sections need to be properly included.

  7. Scattering cancellation by metamaterial cylindrical multilayers

    NASA Astrophysics Data System (ADS)

    Tricarico, S.; Bilotti, F.; Vegni, L.

    2009-05-01

    In this paper, we present the theoretical analysis and the design of cylindrical multilayered electromagnetic cloaks based on the scattering cancellation technique. We propose at first the analysis and the design of bi-layered cylindrical shells, made of homogenous and isotropic metamaterials, in order to effectively reduce the scattered field from a dielectric cylindrical object. The single shell and the bi-layered shell cases are compared in terms of scattering reduction and loss effects. The comparison shows that the bi-layered configuration exhibits superior performances. The scattering cancellation approach, is, then, extended to the case of generic multilayered cylindrical shells, considering again homogeneous and isotropic metamaterials. The employment of the proposed technique to the case of cloaking devices working at multiple frequencies is also envisaged and discussed. Finally, some practical layouts of cylindrical electromagnetic cloaks working at optical frequencies are also proposed. In these configurations, the homogenous and isotropic metamaterials are replaced by their actual counterparts, obtained using alternating stacked plasmonic and non-plasmonic layers. The theoretical formulation and the design approaches presented throughout the paper are validated through proper full-wave numerical simulations.

  8. A clocked high-pass-filter-based offset cancellation technique for high-gain biomedical amplifiers

    NASA Astrophysics Data System (ADS)

    Pal, Dipankar; Goswami, Manish

    2010-05-01

    In this article, a simple offset cancellation technique based on a clocked high-pass filter with extremely low output offset is presented. The configuration uses the on-resistance of a complementary metal oxide semiconductor (CMOS) transmission gate (X-gate) and tunes the lower 3-dB cut-off frequency with a matched pair of floating capacitors. The results compare favourably with the more complex auto-zeroing and chopper stabilisation techniques of offset cancellation in terms of power dissipation, component count and bandwidth, while reporting inferior output noise performance. The design is suitable for use in biomedical amplifier systems for applications such as ENG-recording. The system is simulated in Spectre Cadence 5.1.41 using 0.6 μm CMOS technology and the total block gain is ∼83.0 dB while the phase error is <5°. The power consumption is 10.2 mW and the output offset obtained for an input monotone signal of 5 μVpp is 1.28 μV. The input-referred root mean square noise voltage between 1 and 5 kHz is 26.32 nV/√Hz.

  9. Cardiorespiratory Responses to Acoustic Noise in Belugas.

    PubMed

    Lyamin, Oleg I; Korneva, Svetlana M; Rozhnov, Viatcheslav V; Mukhametov, Lev M

    2016-01-01

    To date, most research on the adverse effects of anthropogenic noise on marine mammals has focused on auditory and behavioral responses. Other responses have received little attention and are often ignored. In this study, the effect of acoustic noise on heart rate was examined in captive belugas. The data suggest that (1) heart rate can be used as a measure of physiological response (including stress) to noise in belugas and other cetaceans, (2) cardiac response is influenced by parameters of noise and adaptation to repeated exposure, and (3) cetacean calves are more vulnerable to the adverse effect of noise than adults. PMID:26611017

  10. A Power-Efficient Capacitive Read-Out Circuit With Parasitic-Cancellation for MEMS Cochlea Sensors.

    PubMed

    Wang, Shiwei; Koickal, Thomas Jacob; Hamilton, Alister; Mastropaolo, Enrico; Cheung, Rebecca; Abel, Andrew; Smith, Leslie S; Wang, Lei

    2016-02-01

    This paper proposes a solution for signal read-out in the MEMS cochlea sensors that have very small sensing capacitance and do not have differential sensing structures. The key challenge in such sensors is the significant signal degradation caused by the parasitic capacitance at the MEMS-CMOS interface. Therefore, a novel capacitive read-out circuit with parasitic-cancellation mechanism is developed; the equivalent input capacitance of the circuit is negative and can be adjusted to cancel the parasitic capacitance. Chip results prove that the use of parasitic-cancellation is able to increase the sensor sensitivity by 35 dB without consuming any extra power. In general, the circuit follows a low-degradation low-amplification approach which is more power-efficient than the traditional high-degradation high-amplification approach; it employs parasitic-cancellation to reduce the signal degradation and therefore a lower gain is required in the amplification stage. Besides, the chopper-stabilization technique is employed to effectively reduce the low-frequency circuit noise and DC offsets. As a result of these design considerations, the prototype chip demonstrates the capability of converting a 7.5 fF capacitance change of a 1-Volt-biased 0.5 pF capacitive sensor pair into a 0.745 V signal-conditioned output at the cost of only 165.2 μW power consumption.

  11. 21 CFR 1305.28 - Canceling and voiding electronic orders.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Canceling and voiding electronic orders. 1305.28... I AND II CONTROLLED SUBSTANCES Electronic Orders § 1305.28 Canceling and voiding electronic orders. (a) A supplier may void all or part of an electronic order by notifying the purchaser of the...

  12. 78 FR 14351 - Invasive Species Advisory Committee; Meeting Cancellation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-05

    ... Office of the Secretary Invasive Species Advisory Committee; Meeting Cancellation AGENCY: Office of the Secretary, Interior. ACTION: Notice of meeting cancellation. SUMMARY: The meeting of the Invasive Species....gov . SUPPLEMENTARY INFORMATION: The ISAC is comprised of 31 nonfederal invasive species experts...

  13. 77 FR 16895 - Taxpayer Advocacy Panel Meeting Cancellation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ... Internal Revenue Service Taxpayer Advocacy Panel Meeting Cancellation AGENCY: Internal Revenue Service (IRS... the open meeting of the Taxpayer Advocacy Panel Taxpayer Burden Reduction Project Committee scheduled... cancelled pending renewal of the Taxpayer Advocacy Panel Charter. FOR FURTHER INFORMATION CONTACT: Audrey...

  14. 77 FR 16895 - Taxpayer Advocacy Panel Meeting Cancellation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ... Internal Revenue Service Taxpayer Advocacy Panel Meeting Cancellation AGENCY: Internal Revenue Service (IRS... open meeting of the Taxpayer Advocacy Panel Small Business/Self-Employed Decreasing Non-Filers Project... meeting is cancelled pending renewal of the Taxpayer Advocacy Panel Charter. FOR FURTHER...

  15. 32 CFR 1615.8 - Cancellation of registration.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 6 2013-07-01 2013-07-01 false Cancellation of registration. 1615.8 Section 1615.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM ADMINISTRATION OF REGISTRATION § 1615.8 Cancellation of registration. The Director of Selective Service...

  16. 32 CFR 1615.8 - Cancellation of registration.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 6 2012-07-01 2012-07-01 false Cancellation of registration. 1615.8 Section 1615.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM ADMINISTRATION OF REGISTRATION § 1615.8 Cancellation of registration. The Director of Selective Service...

  17. 32 CFR 1615.8 - Cancellation of registration.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 6 2011-07-01 2011-07-01 false Cancellation of registration. 1615.8 Section 1615.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM ADMINISTRATION OF REGISTRATION § 1615.8 Cancellation of registration. The Director of Selective Service...

  18. 32 CFR 1615.8 - Cancellation of registration.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 6 2014-07-01 2014-07-01 false Cancellation of registration. 1615.8 Section 1615.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM ADMINISTRATION OF REGISTRATION § 1615.8 Cancellation of registration. The Director of Selective Service...

  19. 32 CFR 1615.8 - Cancellation of registration.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Cancellation of registration. 1615.8 Section 1615.8 National Defense Other Regulations Relating to National Defense SELECTIVE SERVICE SYSTEM ADMINISTRATION OF REGISTRATION § 1615.8 Cancellation of registration. The Director of Selective Service...

  20. 34 CFR 674.55 - Teacher cancellation-Defense loans.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 34 Education 3 2011-07-01 2011-07-01 false Teacher cancellation-Defense loans. 674.55 Section 674... POSTSECONDARY EDUCATION, DEPARTMENT OF EDUCATION FEDERAL PERKINS LOAN PROGRAM Loan Cancellation § 674.55 Teacher... other nonprofit elementary or secondary school; (ii) An institution of higher education; or (iii)...

  1. 9 CFR 166.12 - Cancellation of licenses.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Cancellation of licenses. 166.12 Section 166.12 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE SWINE HEALTH PROTECTION SWINE HEALTH PROTECTION General Provisions § 166.12 Cancellation...

  2. 9 CFR 166.12 - Cancellation of licenses.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Cancellation of licenses. 166.12 Section 166.12 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE SWINE HEALTH PROTECTION SWINE HEALTH PROTECTION General Provisions § 166.12 Cancellation...

  3. 77 FR 5012 - Rescission of Certain Product Cancellations

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-01

    ... 010707-00055, which appeared in FR Doc. 2011-22135, published in the Federal Register of August 31, 2011 (76 FR 54230) (FRL-8885-6). The Cancellation Order was issued following a Notice announcing the... (76 FR 31380(FRL- 8857-1) . However, the request to voluntarily cancel this pesticide product had...

  4. 40 CFR 152.99 - Petitions to cancel registration.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Protection of Data Submitters' Rights § 152.99 Petitions to cancel registration. An original data submitter... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Petitions to cancel registration. 152.99 Section 152.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)...

  5. 30 CFR 281.47 - Cancellation of leases.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Cancellation of leases. 281.47 Section 281.47... OTHER THAN OIL, GAS, AND SULPHUR IN THE OUTER CONTINENTAL SHELF Termination of Leases § 281.47 Cancellation of leases. (a) Whenever the owner of a nonproducing lease fails to comply with any of...

  6. 30 CFR 282.15 - Cancellation of leases.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Cancellation of leases. 282.15 Section 282.15... § 282.15 Cancellation of leases. (a) Whenever the owner of a nonproducing lease fails to comply with any of the provisions of the Act, the lease, or the regulations issued under the Act, and the...

  7. 42 CFR 57.213a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Health Professions Student Loans § 57.213a Loan cancellation reimbursement. (a) For loans made prior to October 22... 42 Public Health 1 2013-10-01 2013-10-01 false Loan cancellation reimbursement. 57.213a Section...

  8. 42 CFR 57.213a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Health Professions Student Loans § 57.213a Loan cancellation reimbursement. (a) For loans made prior to October 22... 42 Public Health 1 2014-10-01 2014-10-01 false Loan cancellation reimbursement. 57.213a Section...

  9. 42 CFR 57.313a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Nursing Student Loans § 57.313a Loan cancellation reimbursement. In the event that insufficient funds are available to... 42 Public Health 1 2014-10-01 2014-10-01 false Loan cancellation reimbursement. 57.313a Section...

  10. 42 CFR 57.313a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Nursing Student Loans § 57.313a Loan cancellation reimbursement. In the event that insufficient funds are available to... 42 Public Health 1 2013-10-01 2013-10-01 false Loan cancellation reimbursement. 57.313a Section...

  11. 42 CFR 57.213a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Health Professions Student Loans § 57.213a Loan cancellation reimbursement. (a) For loans made prior to October 22... 42 Public Health 1 2011-10-01 2011-10-01 false Loan cancellation reimbursement. 57.213a Section...

  12. 42 CFR 57.313a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Nursing Student Loans § 57.313a Loan cancellation reimbursement. In the event that insufficient funds are available to... 42 Public Health 1 2011-10-01 2011-10-01 false Loan cancellation reimbursement. 57.313a Section...

  13. 42 CFR 57.213a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Health Professions Student Loans § 57.213a Loan cancellation reimbursement. (a) For loans made prior to October 22... 42 Public Health 1 2012-10-01 2012-10-01 false Loan cancellation reimbursement. 57.213a Section...

  14. 42 CFR 57.213a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Health Professions Student Loans § 57.213a Loan cancellation reimbursement. (a) For loans made prior to October 22... 42 Public Health 1 2010-10-01 2010-10-01 false Loan cancellation reimbursement. 57.213a Section...

  15. 42 CFR 57.313a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Nursing Student Loans § 57.313a Loan cancellation reimbursement. In the event that insufficient funds are available to... 42 Public Health 1 2010-10-01 2010-10-01 false Loan cancellation reimbursement. 57.313a Section...

  16. 42 CFR 57.313a - Loan cancellation reimbursement.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... CONSTRUCTION OF TEACHING FACILITIES, EDUCATIONAL IMPROVEMENTS, SCHOLARSHIPS AND STUDENT LOANS Nursing Student Loans § 57.313a Loan cancellation reimbursement. In the event that insufficient funds are available to... 42 Public Health 1 2012-10-01 2012-10-01 false Loan cancellation reimbursement. 57.313a Section...

  17. 78 FR 30932 - National Cancer Institute; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-23

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF HEALTH AND HUMAN SERVICES National Institutes of Health National Cancer Institute; Cancellation of Meeting Notice is hereby given of the cancellation of the National Cancer Institute Special Emphasis Panel, June 7, 2013, 10:00 a.m. to June 7, 2013, 1:00...

  18. 30 CFR 282.15 - Cancellation of leases.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Cancellation of leases. 282.15 Section 282.15 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE... Jurisdiction and Responsibilities of Director § 282.15 Cancellation of leases. (a) Whenever the owner of...

  19. 75 FR 30386 - Cancellation Notice of a Sunshine Act Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-01

    ... From the Federal Register Online via the Government Publishing Office ELECTION ASSISTANCE COMMISSION Cancellation Notice of a Sunshine Act Meeting AGENCY: United States Election Assistance Commission (EAC). ACTION: Notice to cancel EAC public meeting. SUMMARY: The U.S. Election Assistance...

  20. 75 FR 33628 - National Cancer Institute; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-14

    ... HUMAN SERVICES National Institutes of Health National Cancer Institute; Cancellation of Meeting Notice is hereby given of the cancellation of the National Cancer Institute Clinical Trials and Translational Research Advisory Committee, July 14, 2010, 8 a.m. to July 14, 2010, 4 p.m., National...

  1. 77 FR 34396 - National Cancer Institute; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-11

    ... HUMAN SERVICES National Institutes of Health National Cancer Institute; Cancellation of Meeting Notice is hereby given of the cancellation of the National Cancer Institute Clinical Trials and Translational Research Advisory Committee, July 11, 2012, 9:00 a.m. to July 11, 2012, 4:00 p.m.,...

  2. 78 FR 69432 - National Institute on Aging; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-19

    ... November 8, 2013, 67177 FR 217. The meeting was entitled Member Conflict. Dated: November 13, 2013. Melanie... HUMAN SERVICES National Institutes of Health National Institute on Aging; Cancellation of Meeting Notice is hereby given of the cancellation of the National Institute on Aging Special Emphasis...

  3. 14 CFR 221.211 - Cancellation of suspended matter.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Cancellation of suspended matter. 221.211 Section 221.211 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... matter. When, pursuant to an order of the Department, the cancellation of rules, fares, charges, or...

  4. 14 CFR 221.211 - Cancellation of suspended matter.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Cancellation of suspended matter. 221.211 Section 221.211 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... matter. When, pursuant to an order of the Department, the cancellation of rules, fares, charges, or...

  5. 14 CFR 221.211 - Cancellation of suspended matter.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Cancellation of suspended matter. 221.211 Section 221.211 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... matter. When, pursuant to an order of the Department, the cancellation of rules, fares, charges, or...

  6. 14 CFR 221.211 - Cancellation of suspended matter.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Cancellation of suspended matter. 221.211 Section 221.211 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... matter. When, pursuant to an order of the Department, the cancellation of rules, fares, charges, or...

  7. 14 CFR 221.211 - Cancellation of suspended matter.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Cancellation of suspended matter. 221.211 Section 221.211 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION... matter. When, pursuant to an order of the Department, the cancellation of rules, fares, charges, or...

  8. 14 CFR 1215.110 - User cancellation of all services.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false User cancellation of all services. 1215.110... RELAY SATELLITE SYSTEM (TDRSS) Use and Reimbursement Policy for Non-U.S. Government Users § 1215.110 User cancellation of all services. The user has the right to terminate its service contract with...

  9. 19 CFR 111.51 - Cancellation of license or permit.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...) Without prejudice. The Assistant Commissioner may cancel a broker's license or permit “without prejudice... in order to avoid those proceedings, he may cancel the license or permit “without prejudice” only with authorization from the Secretary of Homeland Security, or his designee. (b) With prejudice....

  10. 34 CFR 674.55 - Teacher cancellation-Defense loans.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 34 Education 3 2010-07-01 2010-07-01 false Teacher cancellation-Defense loans. 674.55 Section 674... POSTSECONDARY EDUCATION, DEPARTMENT OF EDUCATION FEDERAL PERKINS LOAN PROGRAM Loan Cancellation § 674.55 Teacher... majority of the students whom the borrower teaches are children. (Authority: 20 U.S.C. 425(b)(3))...

  11. 77 FR 27072 - Gastrointestinal Drugs Advisory Committee; Cancellation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-08

    ... Federal Register of March 23, 2012 (77 FR 17078). The meeting is being canceled because the Agency no... HUMAN SERVICES Food and Drug Administration Gastrointestinal Drugs Advisory Committee; Cancellation AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The meeting of the...

  12. 9 CFR 166.12 - Cancellation of licenses.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Cancellation of licenses. 166.12 Section 166.12 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE SWINE HEALTH PROTECTION SWINE HEALTH PROTECTION General Provisions § 166.12 Cancellation...

  13. 9 CFR 166.12 - Cancellation of licenses.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Cancellation of licenses. 166.12 Section 166.12 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE SWINE HEALTH PROTECTION SWINE HEALTH PROTECTION General Provisions § 166.12 Cancellation...

  14. 9 CFR 166.12 - Cancellation of licenses.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Cancellation of licenses. 166.12 Section 166.12 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE SWINE HEALTH PROTECTION SWINE HEALTH PROTECTION General Provisions § 166.12 Cancellation...

  15. 76 FR 56771 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-14

    ... Center, Bethesda, MD 20814 which was published in the Federal Register on September 6, 2011, 76 FR 55076... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  16. 76 FR 34719 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-14

    ..., Bethesda, MD, 20892 which was published in the Federal Register on May 23, 2011, 76 FR 29770-29771. The... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  17. 78 FR 17421 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-21

    ... Drive, Bethesda, MD, 20892 which was published in the Federal Register on March 4, 2013, 78 FR 14099... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  18. 76 FR 31619 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-01

    ..., IL 60611 which was published in the Federal Register on May 3, 2011, 76 FR 24894-24896. The meeting... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  19. 76 FR 27069 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-10

    ..., Bethesda, MD, 20892 which was published in the Federal Register on April 29, 2011, 76 FR 24036-24038. The... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  20. 75 FR 26268 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-11

    ... Road, McLean, VA 22102 which was published in the Federal Register on April 30, 2010, 75 FR 22819. The... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  1. 78 FR 28600 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-15

    ... Drive, Bethesda, MD, 20892 which was published in the Federal Register on May 9, 2013, 78 FR 27244. The... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  2. 78 FR 66028 - Center for Scientific Review; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-04

    ...., Washington, DC 20009, which was published in the Federal Register on September 9, 2013, 78 FR 55087. The... HUMAN SERVICES National Institutes of Health Center for Scientific Review; Cancellation of Meeting Notice is hereby given of the cancellation of the Center for Scientific Review Special Emphasis...

  3. 5 CFR 870.1006 - Cancellation of insurance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATIONS (CONTINUED) FEDERAL EMPLOYEES' GROUP LIFE INSURANCE PROGRAM Benefits for United States Hostages in Iraq and Kuwait and United States Hostages Captured in Lebanon § 870.1006 Cancellation of insurance. (a... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Cancellation of insurance....

  4. 12 CFR 747.406 - Cancellation of charter.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... the Federal credit union has been completed, the NCUA Board shall cancel the charter of the Federal... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Cancellation of charter. 747.406 Section 747... and Procedures Applicable to Proceedings Relating to the Suspension or Revocation of Charters and...

  5. 48 CFR 14.209 - Cancellation of invitations before opening.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... the bids shall be purged from primary and backup data storage systems. (c) The notice of cancellation... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Cancellation of invitations before opening. 14.209 Section 14.209 Federal Acquisition Regulations System FEDERAL...

  6. 48 CFR 14.209 - Cancellation of invitations before opening.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... the bids shall be purged from primary and backup data storage systems. (c) The notice of cancellation... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Cancellation of invitations before opening. 14.209 Section 14.209 Federal Acquisition Regulations System FEDERAL...

  7. 48 CFR 14.209 - Cancellation of invitations before opening.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... the bids shall be purged from primary and backup data storage systems. (c) The notice of cancellation... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Cancellation of invitations before opening. 14.209 Section 14.209 Federal Acquisition Regulations System FEDERAL...

  8. 48 CFR 14.209 - Cancellation of invitations before opening.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... the bids shall be purged from primary and backup data storage systems. (c) The notice of cancellation... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Cancellation of invitations before opening. 14.209 Section 14.209 Federal Acquisition Regulations System FEDERAL...

  9. 48 CFR 14.209 - Cancellation of invitations before opening.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... the bids shall be purged from primary and backup data storage systems. (c) The notice of cancellation... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Cancellation of invitations before opening. 14.209 Section 14.209 Federal Acquisition Regulations System FEDERAL...

  10. 19 CFR 114.34 - Cancellation of erroneous charges.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 1 2014-04-01 2014-04-01 false Cancellation of erroneous charges. 114.34 Section 114.34 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARNETS Miscellaneous § 114.34 Cancellation of erroneous charges. (a) TIR...

  11. 19 CFR 114.34 - Cancellation of erroneous charges.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 1 2011-04-01 2011-04-01 false Cancellation of erroneous charges. 114.34 Section 114.34 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARNETS Miscellaneous § 114.34 Cancellation of erroneous charges. (a) TIR...

  12. 19 CFR 114.34 - Cancellation of erroneous charges.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 1 2013-04-01 2013-04-01 false Cancellation of erroneous charges. 114.34 Section 114.34 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARNETS Miscellaneous § 114.34 Cancellation of erroneous charges. (a) TIR...

  13. 19 CFR 114.34 - Cancellation of erroneous charges.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Cancellation of erroneous charges. 114.34 Section 114.34 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARNETS Miscellaneous § 114.34 Cancellation of erroneous charges. (a) TIR...

  14. 46 CFR 308.511 - Cancellation of Open Cargo Policy.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 8 2012-10-01 2012-10-01 false Cancellation of Open Cargo Policy. 308.511 Section 308.511 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Cargo Insurance Ii-Open Policy War Risk Cargo Insurance § 308.511 Cancellation of...

  15. 46 CFR 308.511 - Cancellation of Open Cargo Policy.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 8 2011-10-01 2011-10-01 false Cancellation of Open Cargo Policy. 308.511 Section 308.511 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Cargo Insurance Ii-Open Policy War Risk Cargo Insurance § 308.511 Cancellation of...

  16. 46 CFR 308.511 - Cancellation of Open Cargo Policy.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 8 2014-10-01 2014-10-01 false Cancellation of Open Cargo Policy. 308.511 Section 308.511 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Cargo Insurance Open Policy War Risk Cargo Insurance § 308.511 Cancellation of Open...

  17. 46 CFR 308.511 - Cancellation of Open Cargo Policy.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 8 2013-10-01 2013-10-01 false Cancellation of Open Cargo Policy. 308.511 Section 308.511 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Cargo Insurance Ii-Open Policy War Risk Cargo Insurance § 308.511 Cancellation of...

  18. 37 CFR 201.7 - Cancellation of completed registrations.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... cancellation and the reasons therefor, and be given 30 days, from the date the Copyright Office letter is... 37 Patents, Trademarks, and Copyrights 1 2014-07-01 2014-07-01 false Cancellation of completed registrations. 201.7 Section 201.7 Patents, Trademarks, and Copyrights U.S. COPYRIGHT OFFICE, LIBRARY...

  19. Discovering Visual Scanning Patterns in a Computerized Cancellation Test

    ERIC Educational Resources Information Center

    Huang, Ho-Chuan; Wang, Tsui-Ying

    2013-01-01

    The purpose of this study was to develop an attention sequential mining mechanism for investigating the sequential patterns of children's visual scanning process in a computerized cancellation test. Participants had to locate and cancel the target amongst other non-targets in a structured form, and a random form with Chinese stimuli. Twenty-three…

  20. 75 FR 13559 - National Cancer Institute; Cancellation of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-22

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF HEALTH AND HUMAN SERVICES National Institutes of Health National Cancer Institute; Cancellation of Meeting Notice is hereby given of the cancellation of the National Cancer Institute Special Emphasis Panel, April...