Study on the infrared radiation performance of Tourmaline composite and its effect on the diesel characteristic

NASA Astrophysics Data System (ADS)

Liao, Jian Bin; Yu, Hong Liang; Sun, Di; Ma, Fong Yuan

2017-09-01

The black tourmaline, magnesium tourmaline, and spinel were ground into powder, and the infrared radiation material was prepared by adding the ceramic powder, clay and the other material into the tourmaline powder according to a certain proportion. The infrared radiation property was tested and analyzed, the diesel was infrared radiation activated by the composite material, and the physicochemical property of fuel oil was analyzed pre-test and post-test. The result shows that the infrared absorption spectrum of the black tourmaline of different particle size is stable. After the diesel oil was infrared radiation activated by tourmaline composite materials, the physicochemical property of diesel oil was changed, the activation energy decreased, the viscosity and surface tension of fuel oil were reduced.

Characterisation of spray dried soy sauce powders made by adding crystalline carbohydrates to drying carrier.

PubMed

Wang, Wei; Zhou, Weibiao

2015-02-01

This study aimed to reduce stickiness and caking of spray dried soy sauce powders by introducing a new crystalline structure into powder particles. To perform this task, soy sauce powders were formulated by using mixtures of cellulose and maltodextrin or mixtures of waxy starch and maltodextrin as drying carriers, with a fixed carrier addition rate of 30% (w/v) in the feed solution. The microstructure, crystallinity, solubility as well as stickiness and caking strength of all the different powders were analysed and compared. Incorporating crystalline carbohydrates in the drying carrier could significantly reduce the stickiness and caking strength of the powders when the ratio of crystalline carbohydrates to maltodextrin was above 1:5 and 1:2, respectively. X-ray Diffraction (XRD) results showed that adding cellulose or waxy starch could induce the crystallinity of powders. Differential Scanning Calorimetry (DSC) results demonstrated that the native starch added to the soy sauce powders did not fully gelatinize during spray drying. Copyright © 2014 Elsevier Ltd. All rights reserved.

Rheological, physical and sensorial evaluation of cookies supplemented with dairy powders.

PubMed

Sert, Durmuş; Demir, M Kürşat; Ertaş, Nilgün

2016-04-01

The effect of dairy powders (skim milk powder, butter milk powder, sodium caseinate, yoghurt powder, milk powder and colostrum powder) on cookie quality was studied. Cookies were tested for aw, calorimetric energy, diameter, thickness, spread ratio, breaking strength, colour, dough consistency and sensory evaluation. The lowest aw values were obtained for cookies containing colostrum powder; also the highest calorimetric energy values were obtained from the colostrum powder-added cookies. Diameter values of cookies with the addition of skim milk powder, butter milk powder, yoghurt powder and milk powder were higher than that of sodium caseinate and colostrum powder. The lowest spread ratio was measured in the cookie samples with added skim milk powder. The addition of yoghurt powder gave the highest breaking strength of cookies. Cookies with sodium caseinate addition exhibited the highest lightness (L*) values than the other cookies with different dairy powders. Cookies prepared with butter milk powder received the highest scores for colour, appearance, texture, crispness and overall acceptability. © The Author(s) 2015.

Color, bioactive compounds and morphological characteristics of encapsulated Asian pear juice powder during spray drying.

PubMed

Lee, Chang-Gon; Ahmed, Maruf; Jiang, Gui-Hun; Eun, Jong-Bang

2017-08-01

Encapsulated Asian pear juice powder was produced through spray drying using three maltodextrin levels (15, 20, and 25% w/v) and three inlet air temperatures (130, 150, and 170 °C). The impact of maltodextrin concentrations and inlet air temperatures on color, bioactive compounds, and morphological characteristics of encapsulated Asian pear juice powder were investigated. Maltodextrin concentrations and inlet air temperatures significantly influenced L * and b * values of encapsulated Asian pear juice powder. Increasing inlet air temperatures increased total phenolic content, whereas the vitamin C content decreased. Vitamin C content was strongly correlated with particle size, inlet air temperature, and maltodextrin concentration. ABTS + radical-scavenging activity was highly correlated with total phenol content while DPPH radical-scavenging activity was highly correlated with vitamin C content. Encapsulated powders made with higher inlet air temperature and higher maltodextrin concentration had lowest median particle diameter with a smoother, more regular and rounded outer surface than those of encapsulated powders produced with lower inlet air temperature and lower maltodextrin concentration. Therefore, the results demonstrate that high-quality encapsulated Asian pear juice powder could be manufactured by adding 15% (w/v) maltodextrin and spray-drying at 170 °C.

Optimized aqueous extraction of saponins from bitter melon for production of a saponin-enriched bitter melon powder.

PubMed

Tan, Sing P; Vuong, Quan V; Stathopoulos, Costas E; Parks, Sophie E; Roach, Paul D

2014-07-01

Bitter melon, Momordica charantia L. (Cucurbitaceae), aqueous extracts are proposed to have health-promoting properties due to their content of saponins and their antioxidant activity. However, the optimal conditions for the aqueous extraction of saponins from bitter melon and the effects of spray drying have not been established. Therefore, this study aimed to optimize the aqueous extraction of the saponins from bitter melon, using response surface methodology, prepare a powder using spray drying, and compare the powder's physical properties, components, and antioxidant capacity with aqueous and ethanol freeze-dried bitter melon powders and a commercial powder. The optimal aqueous extraction conditions were determined to be 40 °C for 15 min and the water-to-sample ratio was chosen to be 20:1 mL/g. For many of its physical properties, components, and antioxidant capacity, the aqueous spray-dried powder was comparable to the aqueous and ethanol freeze-dried bitter melon powders and the commercial powder. The optimal conditions for the aqueous extraction of saponins from bitter melon followed by spray drying gave a high quality powder in terms of saponins and antioxidant activity. This study highlights that bitter melon is a rich source of saponin compounds and their associated antioxidant activities, which may provide health benefits. The findings of the current study will help with the development of extraction and drying technologies for the preparation of a saponin-enriched powdered extract from bitter melon. The powdered extract may have potential as a nutraceutical supplement or as a value-added ingredient for incorporation into functional foods. © 2014 Institute of Food Technologists®

Comparison of different drying methods on the physical properties, bioactive compounds and antioxidant activity of raspberry powders.

PubMed

Si, Xu; Chen, Qinqin; Bi, Jinfeng; Wu, Xinye; Yi, Jianyong; Zhou, Linyan; Li, Zhaolu

2016-04-01

Dehydration has been considered as one of the traditional but most effective techniques for perishable fruits. Raspberry powders obtained after dehydration can be added as ingredients into food formulations such as bakery and dairy products. In this study, raspberry powders obtained by hot air drying (HAD), infrared radiation drying (IRD), hot air and explosion puffing drying (HA-EPD), infrared radiation and microwave vacuum drying (IR-MVD) and freeze drying (FD) were compared on physical properties, bioactive compounds and antioxidant activity. Drying techniques affected the physical properties, bioactive compounds and antioxidant activity of raspberry powders greatly. FD led to significantly higher (P < 0.05) values of water solubility (45.26%), soluble solid (63.46%), hygroscopicity (18.06%), color parameters and anthocyanin retention (60.70%) of raspberry powder compared with other drying methods. However, thermal drying techniques, especially combined drying methods, were superior to FD in final total polyphenol content, total flavonoid content and antioxidant activity. The combined drying methods, especially IR-MVD, showed the highest total polyphenol content (123.22 g GAE kg(-1) dw) and total flavonoid content (0.30 g CAE kg(-1) dw). Additionally, IR-MVD performed better in antioxidant activity retention. Overall, combined drying methods, especially IR-MVD, were found to result in better quality of raspberry powders among the thermal drying techniques. IR-MVD could be recommended for use in the drying industry because of its advantages in time saving and nutrient retention. © 2015 Society of Chemical Industry.

Production of crispy bread snacks containing chicken meat and chicken meat powder.

PubMed

Cakmak, Hulya; Altinel, Burak; Kumcuoglu, Seher; Kisla, Duygu; Tavman, Sebnem

2016-01-01

Chicken meat in two different forms (chicken meat and chicken meat powder) were added into white flour and whole wheat blend baguette bread formulations for protein enrichment and finally developing new and healthy snacks. The chicken meat and powder levels were 10% for white flour baguette, and 15% for whole wheat blend. The dried baguette samples were packaged under 100% N2, and physical, chemical, microbiological and sensorial properties were evaluated during 3 months of storage. Protein content of chicken meat powder added samples were found statistically higher than chicken meat added samples. Hardness of the snacks was significantly affected from type of chicken meat, such as values were higher for chicken meat added samples than chicken meat powder added samples. Lipid oxidation of the snacks was determined by TBA analysis, and TBA value for whole wheat mixture snack with 15% of chicken meat was the highest among all during storage. The highest overall acceptance score was obtained from white flour snack with 10% chicken meat. There was no coliform bacteria detected during storage and the results of yeast-mold count and aerobic plate count of snacks remained between the quantitative ranges.

Functional analysis of unfermented and fermented citrus peels and physical properties of citrus peel-added doughs for bread making.

PubMed

Shyu, Yung-Shin; Lu, Tzu-Chi; Lin, Chuan-Chuan

2014-12-01

Several studies have indicated citrus peels (CP) contain specific methoxy flavones, e.g. nobiletin and tangeretin, which have been shown to prevent numerous diseases. However, research reports regarding their application as food additive in healthy baked products is scarce. In our study, both unfermented (UF) and fermented (F) citrus peels were processed under different dry hot-air temperatures to make four citrus peel powders , UF-100 °C,UF-150 °C, F-100 °C, F-150 °C, respectively. The analysis of the basic components and nutraceuticals as well as antioxidant activity were conducted. Various percentages of CP were added to dough and toast bread for physical property and sensory evaluations. The results indicated the contents of crude proteins (3.3-4.3 mg/g) and fibers (10.9-14.9 %) among the four samples were similar. The UF extracts showed better antioxidant activities than F extracts. HPLC analysis indicated the contents of hesperidine, nobiletin and tangeretin in CP extracts were UF-150 °C > UF-100 °C. Farinograph analysis indicated a linear relation between CP powder content and the parameters of the physical properties of dough. A high percentage of fibrous CP powder in dough increases the water adsorption capacity of the dough, resulting in a decrease in its stability The sensory evaluation results indicated a greater acceptability of UF-added toast bread relative to the F-added one. Among these, according to the statistical anaylsis, the UF-150 °C 4 % and UF-100 °C 6 % groups were the best and F-150 °C 2 % group was the poorest in overall acceptability.

The Sustained Delivery of Resveratrol or a Defined Grape Powder Inhibits New Blood Vessel Formation in a Mouse Model of Choroidal Neovascularization

PubMed Central

Kanavi, Mozhgan Rezaie; Darjatmoko, Soesiawati; Wang, Shoujian; Azari, Amir A.; Farnoodian, Mitra; Kenealey, Jason D.; van Ginkel, Paul R.; Albert, Daniel M.; Sheibani, Nader; Polans, Arthur S.

2015-01-01

The objective of this study was to determine whether resveratrol or a defined, reconstituted grape powder can attenuate the formation of new blood vessels in a mouse model of choroidal neovascularization (CNV). To accomplish this objective, C57BL/6J mice were randomized into control or treatment groups which received either resveratrol or grape powder by daily oral gavage, resveratrol or grape powder delivered ad libitum through the drinking water, or resveratrol by slow release via implanted osmotic pumps. A laser was used to rupture Bruch’s membrane to induce CNV which was then detected in sclerochoroidal eyecups stained with antibodies against intercellular adhesion molecule-2. CNV area was measured using fluorescence microscopy and Image J software. Ad libitum delivery of both resveratrol and grape powder was shown to significantly reduce the extent of CNV by 68% and 57%, respectively. Parallel experiments conducted in vitro demonstrated that resveratrol activates p53 and inactivates Akt/protein kinase B in choroidal endothelial cells, contributing to its anti-proliferative and anti-migratory properties. In addition resveratrol was shown to inhibit the formation of endothelial cell networks, augmenting its overall anti-angiogenic effects. The non-toxic nature of resveratrol makes it an especially attractive candidate for the prevention and/or treatment of CNV. PMID:25361423

The effects of boric acid and phosphoric acid on the compressive strength of glass-ionomer cements.

PubMed

Prentice, Leon H; Tyas, Martin J; Burrow, Michael F

2006-01-01

Both boric acid (H3BO3) and phosphoric acid (H3PO4) are components of dental cements, commonly incorporated into glass (as ingredients in the melt) and occasionally added to the powder or liquid components. This study investigated the effect of boric acid addition to an experimental glass-ionomer powder and the effect of phosphoric acid addition to a glass-ionomer liquid on the 24-h compressive strength. Boric acid powder was added in various concentrations to an experimental glass-ionomer powder and, separately, phosphoric acid was added to an experimental glass-ionomer liquid. Powders and liquids were dosed into capsules at various powder:liquid ratios and cements thus formed were assessed for 24-h compressive strength. Incorporation of boric acid in glass-ionomer powder resulted in a pronounced decrease (p < 0.05 at 1% boric acid) in compressive strength. Addition of phosphoric acid produced initially stronger cements (up to 13% increase at 1% phosphoric acid) before also declining. The incorporation of less than 2% w/w phosphoric acid in glass-ionomer liquids may improve cement strengths without compromising clinical usefulness. The incorporation of boric acid in glass-ionomer cements is contraindicated.

Cheese powder as an ingredient in emulsion sausages: Effect on sensory properties and volatile compounds.

PubMed

Xiang, Chen; Ruiz-Carrascal, Jorge; Petersen, Mikael A; Karlsson, Anders H

2017-08-01

Different types of cheese powder were added to meat emulsion sausages in order to address its influence on chemical composition, volatile compounds profile and sensory properties, and its potential to reduce salt content through boosting saltiness. Addition of cheese powder to emulsion sausages modified their profile of volatile compounds. Blue cheese increased some ketones, alcohols, and esters, while brown cheese brought typical Maillard reaction compounds. Overall, addition of cheese powders to sausages enhanced the intensity of flavour traits. A mixture of hard and blue cheese powder showed the highest effect on boosting saltiness, while brown cheese powder showed the strongest umami and meat flavour boosting effect, and sausages with added blue cheese powder showed a more intense aftertaste. Hardness significantly increased due to the addition of blue cheese powder. Addition of cheese powder to emulsion sausages might be an interesting tool to boost flavour and reduce salt content in cooked sausages with no negative effect on saltiness or overall flavour. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of Micronutrient Powder Addition on Sensory Properties of Foods for Older Adults.

PubMed

Field, Katherine M; Duncan, Alison M; Keller, Heather H; Stark, Ken D; Duizer, Lisa M

2017-10-01

Micronutrient fortification can improve nutrient intake of older adults in long-term care. However, previous studies indicate that micronutrient fortification can alter food sensory attributes and, potentially, consumer liking. Others have found no effect of fortification on liking. This research investigates the effect of micronutrient powder addition on the sensory properties of selected foods commonly served in long-term care. A micronutrient powder containing 9 vitamins and 3 minerals was added to tomato soup and oatmeal at different levels. Using projective mapping, changes in sensory properties were observed with powder addition. Descriptive analysis, used to quantify these changes, showed that both the tomato soup and oatmeal had reduced flavor as the amount of added micronutrient powder increased. Oatmeal also showed changes in texture with fortification. Consumer liking scores for tomato soup showed that micronutrient addition affected liking when 100% of a daily dose was added into the soup. Addition of 50% of the daily dose did not affect liking. Oatmeal liking did not differ between fortified and unfortified samples. Results from this research can be used to decide whether a micronutrient powder of selected vitamins and minerals can be added to foods served to older adults in long-term care. Although sensory properties of the foods will be altered, fortification of both tomato soup and oatmeal with the developed powder is possible without reducing consumer liking to the point where it is disliked. © 2017 Institute of Food Technologists®.

Supplementation of Syzygium cumini seed powder prevented obesity, glucose intolerance, hyperlipidemia and oxidative stress in high carbohydrate high fat diet induced obese rats.

PubMed

Ulla, Anayt; Alam, Md Ashraful; Sikder, Biswajit; Sumi, Farzana Akter; Rahman, Md Mizanur; Habib, Zaki Farhad; Mohammed, Mostafe Khalid; Subhan, Nusrat; Hossain, Hemayet; Reza, Hasan Mahmud

2017-06-02

Obesity and related complications have now became epidemic both in developed and developing countries. Cafeteria type diet mainly composed of high fat high carbohydrate components which plays a significant role in the development of obesity and metabolic syndrome. This study investigated the effect of Syzygium cumini seed powder on fat accumulation and dyslipidemia in high carbohydrate high fat diet (HCHF) induced obese rats. Male Wistar rats were fed with HCHF diet ad libitum, and the rats on HCHF diet were supplemented with Syzygium cumini seed powder for 56 days (2.5% w/w of diet). Oral glucose tolerance test, lipid parameters, liver marker enzymes (AST, ALT and ALP) and lipid peroxidation products were analyzed at the end of 56 days. Moreover, antioxidant enzyme activities were also measured in all groups of rats. Supplementation with Syzygium cumini seed powder significantly reduced body weight gain, white adipose tissue (WAT) weights, blood glucose, serum insulin, and plasma lipids such as total cholesterol, triglyceride, LDL and HDL concentration. Syzygium cumini seed powder supplementation in HCHF rats improved serum aspartate amino transferase (AST), alanine amino transferase (ALT), and alkaline phosphatase (ALP) activities. Syzygium cumini seed powder supplementation also reduced the hepatic thiobarbituric acid reactive substances (TBARS) and elevated the antioxidant enzyme superoxide dismutase (SOD) and catalase (CAT) activities as well as increased glutathione (GSH) concentration. In addition, histological assessment showed that Syzygium cumini seed powder supplementation prevented inflammatory cell infiltration; fatty droplet deposition and fibrosis in liver of HCHFD fed rats. Our investigation suggests that Syzygium cumini seed powder supplementation prevents oxidative stress and showed anti-inflammatory and antifibrotic activity in liver of HCHF diet fed rats. In addition, Syzygium cumini seed powder may be beneficial in ameliorating insulin resistance and dyslipidemia probably by increasing lipid metabolism in liver of HCHF diet fed rats.

Effect of pineapple waste powder on probiotic growth, antioxidant and antimutagenic activities of yogurt.

PubMed

Sah, B N P; Vasiljevic, T; McKechnie, S; Donkor, O N

2016-03-01

Although many fruit by-products are good sources of nutrients, little is known about their prebiotic potential. This research was aimed at establishing the prebiotic effect of pineapple wastes on probiotics including Lactobacillus (L.) acidophilus (ATCC® 4356™), L. casei (ATCC® 393™) and L. paracasei spp. paracasei (ATCC® BAA52™) and the subsequent release of antioxidant and antimutagenic peptides in yogurt during their growth. Oven- and freeze- dried peel and pomace were milled separately into powders and tested for prebiotic activities. The net probiotic growth (1.28-2.14 log cfu/g) in customized MRS broth containing the pineapple powders as a direct carbohydrate source was comparable to MRS broth containing glucose. The powders were also separately added to milk during the manufacturing of yogurt with or without probiotics. An increase (by 0.3-1.4 log cycle) in probiotic populations was observed in the yogurts as a consequence of pineapple powder supplementation. Crude water-soluble peptide extracts, prepared by high-speed centrifugation of the yogurts, displayed remarkable antioxidant activities assessed through in vitro assays, namely scavenging activity of 1,1-diphenyl-2-picrylhydrazyl radicals (IC50 = 0.37-0.19 mg/ml) and hydroxyl radicals (58.52-73.55 %). The peptide extracts also exhibited antimutagenic activities (18.60-32.72 %) as sodium azide inhibitor in the Salmonella mutagenicity test. Together, these results suggest that pineapple by-products exhibited prebiotic properties and could possibly be commercially applied in new functional food formulations.

Prelithiation of silicon-carbon nanotube anodes for lithium ion batteries by stabilized lithium metal powder (SLMP).

PubMed

Forney, Michael W; Ganter, Matthew J; Staub, Jason W; Ridgley, Richard D; Landi, Brian J

2013-09-11

Stabilized lithium metal powder (SLMP) has been applied during battery assembly to effectively prelithiate high capacity (1500-2500 mAh/g) silicon-carbon nanotube (Si-CNT) anodes, eliminating the 20-40% first cycle irreversible capacity loss. Pressure-activation of SLMP is shown to enhance prelithiation and enable capacity matching between Si-CNT anodes and lithium nickel cobalt aluminum oxide (NCA) cathodes in full batteries with minimal added mass. The prelithiation approach enables high energy density NCA/Si-CNT batteries achieving >1000 cycles at 20% depth-of-discharge.

Composition and process for making an insulating refractory material

DOEpatents

Pearson, A.; Swansiger, T.G.

1998-04-28

A composition and process are disclosed for making an insulating refractory material. The composition includes calcined alumina powder, flash activated alumina powder, an organic polymeric binder and a liquid vehicle which is preferably water. Starch or modified starch may also be added. A preferred insulating refractory material made with the composition has a density of about 2.4--2.6 g/cm{sup 3} with reduced thermal conductivity, compared with tabular alumina. Of importance, the formulation has good abrasion resistance and crush strength during intermediate processing (commercial sintering) to attain full strength and refractoriness.

Effects of ozonation, powdered activated carbon adsorption, and coagulation on the removal of disinfection by-product precursors in reservoir water.

PubMed

Wang, Feng; Gao, Baoyu; Yue, Qinyan; Bu, Fan; Shen, Xue

2017-07-01

Effects of ozonation and powdered activated carbon on removal of dissolved organic matter (DOM) and disinfection by-product (DBP) in reservoir water were intensively investigated in this study. Both the formation of carbonaceous DBP (C-DBP) and nitrogenous DBP (N-DBP) as well as their speciation were analyzed. Results exhibited that the addition of powdered activated carbon (PAC) greatly improved the removal of aromatic protein. Trihalomethanes (THMs) and haloacetonitriles (HANs) were the dominant species in C-DBP and N-DBP. The integrated coagulation and PAC processes could remove more than 70% of THMs and 93% of HANs precursors, while only 10.5 and 45% of capture were achieved by the single coagulation. The added ozone lowered the yields of HANs but synchronously increased the more toxic bromine-containing THMs from 78.5 to 128.1 μg/L. Kinetics parameters for THM formation indicated that the precursor creating the THMs fast could be easily removed by both the coagulation and PAC adsorption.

Cinnamon and Its Metabolite Sodium Benzoate Attenuate the Activation of p21rac and Protect Memory and Learning in an Animal Model of Alzheimer's Disease.

PubMed

Modi, Khushbu K; Roy, Avik; Brahmachari, Saurabh; Rangasamy, Suresh B; Pahan, Kalipada

2015-01-01

This study underlines the importance of cinnamon, a commonly used natural spice and flavoring material, and its metabolite sodium benzoate (NaB) in attenuating oxidative stress and protecting memory and learning in an animal model of Alzheimer's disease (AD). NaB, but not sodium formate, was found to inhibit LPS-induced production of reactive oxygen species (ROS) in mouse microglial cells. Similarly, NaB also inhibited fibrillar amyloid beta (Aβ)- and 1-methyl-4-phenylpyridinium(+)-induced microglial production of ROS. Although NaB reduced the level of cholesterol in vivo in mice, reversal of the inhibitory effect of NaB on ROS production by mevalonate, and geranylgeranyl pyrophosphate, but not cholesterol, suggests that depletion of intermediates, but not end products, of the mevalonate pathway is involved in the antioxidant effect of NaB. Furthermore, we demonstrate that an inhibitor of p21rac geranylgeranyl protein transferase suppressed the production of ROS and that NaB suppressed the activation of p21rac in microglia. As expected, marked activation of p21rac was observed in the hippocampus of subjects with AD and 5XFAD transgenic (Tg) mouse model of AD. However, oral feeding of cinnamon (Cinnamonum verum) powder and NaB suppressed the activation of p21rac and attenuated oxidative stress in the hippocampus of Tg mice as evident by decreased dihydroethidium (DHE) and nitrotyrosine staining, reduced homocysteine level and increased level of reduced glutathione. This was accompanied by suppression of neuronal apoptosis, inhibition of glial activation, and reduction of Aβ burden in the hippocampus and protection of memory and learning in transgenic mice. Therefore, cinnamon powder may be a promising natural supplement in halting or delaying the progression of AD.

Effect of solution combusted TiO2 nanopowder within commercial BaTiO3 dielectric layer on the photoelectric properties for AC powder electroluminescence devices.

PubMed

Park, Sung; Choi, Gil Rak; Kim, Youn Cheol; Lee, Jae Chun; Lee, Ju Hyeon

2013-05-01

A unique synthesis method was developed, which is called solution combustion method (SCM). TiO2 nanopowder was synthesized by this method. This SCM TiO2 nanopowder (-35 nm) was added to the dielectric layer of AC powder electroluminescence (EL) device. The dielectric layer was made of commercial BaTiO3 powder (-1.2 microm) and binding polymer. 0, 5, 10 and 15 wt% of SCM TiO2 nanopowder was added to the dielectric layer during fabrication of AC powder EL device respectively. Dielectric constant of these four kinds of dielectric layers was measured. The brightness and current density of AC powder EL device were also measured. When 10 wt% of SCM TiO2 nanopowder was added, dielectric constant and brightness were increased by 30% and 101% respectively. Furthermore, the current density was decreased by 71%. This means that the brightness was double and the power consumption was one third.

Fabricating solid carbon porous electrodes from powders

DOEpatents

Kaschmitter, James L.; Tran, Tri D.; Feikert, John H.; Mayer, Steven T.

1997-01-01

Fabrication of conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive dionization, and waste treatment. Electrodes fabricated from low surface area (<50 m.sup.2 /gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon compositives with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to be high surface area carbons, fuel cell electrodes can be produced.

Fabricating solid carbon porous electrodes from powders

DOEpatents

Kaschmitter, J.L.; Tran, T.D.; Feikert, J.H.; Mayer, S.T.

1997-06-10

Fabrication is described for conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive deionization, and waste treatment. Electrodes fabricated from low surface area (<50 m{sup 2}/gm) graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon composites with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to high surface area carbons, fuel cell electrodes can be produced. 1 fig.

Guava (Psidium guajava L.) Powder as an Antioxidant Dietary Fibre in Sheep Meat Nuggets

PubMed Central

Verma, Arun K.; Rajkumar, V.; Banerjee, Rituparna; Biswas, S.; Das, Arun K.

2013-01-01

This study was conducted to explore the antioxidant potential and functional value of guava (Psidium guajava L.) powder in muscle foods. Guava powder was used as a source of antioxidant dietary fibre in sheep meat nuggets at two different levels i.e., 0.5% (Treatment I) and 1.0% (Treatment II) and its effect was evaluated against control. Guava powder is rich in dietary fibre (43.21%), phenolics (44.04 mg GAE/g) and possesses good radical scavenging activity as well as reducing power. Incorporation of guava powder resulted in significant decrease (p<0.05) in pH of emulsion and nuggets, emulsion stability, cooking yield and moisture content of nuggets while ash and moisture content of emulsion were increased. Total phenolics, total dietary fibre (TDF) and ash content significantly increased (p<0.05) in nuggets with added guava powder. Product redness value was significantly improved (p<0.05) due to guava powder. Textural properties did not differ significantly except, springiness and shear force values. Guava powder was found to retard lipid peroxidation of cooked sheep meat nuggets as measured by TBARS number during refrigerated storage. Guava powder did not affect sensory characteristics of the products and can be used as source of antioxidant dietary fibre in meat foods. PMID:25049864

Mold-Ripened Soft Cheeses Fortified with Date Palm Fruit Product as Functional Dairy Products.

PubMed

Al-Otaibi, Mutlag M; Haddadin, Jamal S; Haddadin, Malik S Y

2016-01-01

Date fruit based products are gaining popularity among the consumers in almost all date growing countries due to its added nutritional value. Therefore, novel products were developed by combining two types of foods i.e., soft ripened cheeses and date fruit syrups or date powder. This study is the first to report the surface mold-ripened cheese production with date syrup and date powder. Model cheeses were prepared from pasteurized milk inoculated with Streptococcus thermophilus, Penicillium camemberti and Geotrichum candidum. Date syrup-1, date syrup-2, date powder or the date mixture were added at the stage of curdling. Based on the kinetic growth of the microbial groups in all the treatments, there was no change in the growth of these in various date palm product. On the contrary It may be said that addition of the date fruit product supports their growth. After 35 days, the amounts of total poly phenols were 128.3 ± 1.01, 81.8 ± 1.11, 33.5 ± 2.19, 156.23 ± 1.27 mg GAE/100 g in the cheeses support with date syrup-1, date syrup-2, date powder or the date mixture, respectively. Antioxidant activity of date fruits ranged from 80.13 IC50 (date syrup-2) to 82.23 IC50 (date syrup-1). Based on the chemical characteristics and sensory analysis, the study results showed the potential for innovative application of date products for developing new functional dairy products as an ideal medium for the delivery of biological active compounds with beneficial health effects over.

Injection molded plastic helical gear filled with carbon powder made from rice hull

NASA Astrophysics Data System (ADS)

Chen, Yen Chu; Itagaki, Takayoshi; Takahashi, Hideo; Takahashi, Mikio

2017-07-01

Natural materials are focused on the ecological responsibility, all over the world. The rice-hull contains natural silica about 20 wt.%. Therefore, a carbonized rice-hull; Rice-Hull-Silica-Carbon (RHSC) is focused as effective utilization of the discarded rice hull. In this study, test plastic helical gears were made form polyacetal copolymer filled with RHSC powder by injection molding. Test helical gears were operated on endurance test. The bulk temperature and noise of test gears were measured during gears operation. Then, the tooth damage of test gears were investigated by using optical microscope. It is clarified that difference of tooth damage by kind of test gears. Moreover, the transition of gear bulk temperature and noise during operation are investigated. Based on these results, the effect of RHSC powder is discussed. From the discussions, it seems reasonable to conclude : (1) The heat resistance of plastic gear is improved by adding the RHSC powder. (2) The fatigue life of plastic gear is improved by adding suitable amount of the RHSC powder. (3) The sound pressure level of plastic gear is reduced by adding the smaller median grain diameter of RHSC powder.

Structural Characterization and Absolute Luminescence Efficiency Evaluation of Gd2O2S High Packing Density Ceramic Screens Doped with Tb3+ and Eu3+ for further Applications in Radiology

NASA Astrophysics Data System (ADS)

Dezi, Anna; Monachesi, Elenasophie; D'Ignazio, Michela; Scalise, Lorenzo; Montalto, Luigi; Paone, Nicola; Rinaldi, Daniele; Mengucci, Paolo; Loudos, George; Bakas, Athanasios; Michail, Christos; Valais, Ioannis; Fountzoula, Christine; Fountos, George; David, Stratos

2017-11-01

Rare earth activators are impurities added in the phosphor material to enhance probability of visible photon emission during the luminescence process. The main activators employed are rare earth trivalent ions such as Ce+3, Tb+3, Pr3+ and Eu+3. In this work, four terbium-activated Gd2O2S (GOS) powder screens with different thicknesses (1049 mg/cm2, 425.41 mg/cm2, 313 mg/cm2 and 187.36 mg/cm2) and one europium-activated GOS powder screen (232.18 mg/cm2) were studied to investigate possible applications for general radiology detectors. Results presented relevant differences in crystallinity between the GOS:Tb doped screens and GOS:Eu screens in respect to the dopant agent present. The AE (Absolute efficiency) was found to rise (i) with the increase of the X-ray tube voltage with the highest peaking at 110kVp and (ii) with the decrease of the thickness among the four GOS:Tb. Comparing similar thickness values, the europium-activated powder screen showed lower AE than the corresponding terbium-activated.

Effects of Purple-fleshed Sweet Potato (Ipomoera batatas Cultivar Ayamurasaki) Powder Addition on Color and Texture Properties and Sensory Characteristics of Cooked Pork Sausages during Storage

PubMed Central

Jin, Sang-Keun; Kim, Yeong-Jung; Park, Jae Hong; Hur, In-Chul; Nam, Sang-Hae; Shin, Daekeun

2012-01-01

This study was conducted to evaluate the effects of adding purple-fleshed sweet potato (PFP) powder on the texture properties and sensory characteristics of cooked pork sausage. Sodium nitrite alone and sodium nitrite in combination with PFP were added to five different treatments sausages (CON (control) = 0.01% sodium nitrite, SP25 = 0.005% sodium nitrite and 0.25% purple-fleshed sweet potato powder combination, SP50 = 0.005% sodium nitrite and 0.5% purple-fleshed sweet potato powder combination, PP25 = 0.25% purple-fleshed sweet potato powder, PP50 = 0.5% purple-fleshed sweet potato powder). The sausages were cooked to 74°C, stored at 4°C for 6 wks, and used for chemical analysis, textural properties, and a sensory evaluation on 0, 2, 4 and 6 wks of storage, respectively. Similar CIE a* and b* values were determined in sausages from CON, SP25 and SP50 at the end of storage, and they were higher in CIE a* but lower in CIE b* than that of the PP25 and PP50 sausages. Significant differences were observed for brittleness and hardness when PFP was added to the sausages but were not confirmed after 4 wks of storage. The objective color score was influenced by adding PFP; however, the effect was not dose dependent. In overall acceptability, panelists favored the CON, SP25, SP50, and PP50 sausages but did not prefer PP25 sausages at the end of storage. Therefore, adding PFP to cooked pork sausages improved color and texture properties and sensory characteristics, but further study is needed to determine the proper ratio of sodium nitrite and PFP. PMID:25049698

Effects of Purple-fleshed Sweet Potato (Ipomoera batatas Cultivar Ayamurasaki) Powder Addition on Color and Texture Properties and Sensory Characteristics of Cooked Pork Sausages during Storage.

PubMed

Jin, Sang-Keun; Kim, Yeong-Jung; Park, Jae Hong; Hur, In-Chul; Nam, Sang-Hae; Shin, Daekeun

2012-09-01

This study was conducted to evaluate the effects of adding purple-fleshed sweet potato (PFP) powder on the texture properties and sensory characteristics of cooked pork sausage. Sodium nitrite alone and sodium nitrite in combination with PFP were added to five different treatments sausages (CON (control) = 0.01% sodium nitrite, SP25 = 0.005% sodium nitrite and 0.25% purple-fleshed sweet potato powder combination, SP50 = 0.005% sodium nitrite and 0.5% purple-fleshed sweet potato powder combination, PP25 = 0.25% purple-fleshed sweet potato powder, PP50 = 0.5% purple-fleshed sweet potato powder). The sausages were cooked to 74°C, stored at 4°C for 6 wks, and used for chemical analysis, textural properties, and a sensory evaluation on 0, 2, 4 and 6 wks of storage, respectively. Similar CIE a* and b* values were determined in sausages from CON, SP25 and SP50 at the end of storage, and they were higher in CIE a* but lower in CIE b* than that of the PP25 and PP50 sausages. Significant differences were observed for brittleness and hardness when PFP was added to the sausages but were not confirmed after 4 wks of storage. The objective color score was influenced by adding PFP; however, the effect was not dose dependent. In overall acceptability, panelists favored the CON, SP25, SP50, and PP50 sausages but did not prefer PP25 sausages at the end of storage. Therefore, adding PFP to cooked pork sausages improved color and texture properties and sensory characteristics, but further study is needed to determine the proper ratio of sodium nitrite and PFP.

Defect Control of the WC Hardmetal by Mixing Recycled WC Nano Powder and Tungsten Powder

NASA Astrophysics Data System (ADS)

Hur, Man Gyu; Shin, Mi Kyung; Kim, Deug Joong; Yoon, Dae Ho

2018-03-01

Tungsten metal powder was added to recycled WC nano powder to control the macro and micro defects of WC hardmetal. The macro and micro defects caused by the excess carbon in the recycled WC powder were markedly removed after the addition of tungsten metal powder ranging from 2 to 6 wt%. The density and hardness of the WC hardmetals also increased due to the removal of defects after adding the tungsten metal powder. The density and hardness of WC hardmetals with the addition of W metal powder ranged from 8 to 12 wt% increased linearly as the W metal powder content increased due to the formation of a new (Co- and W-rich WC) composition. The surface morphology of the WC hardmetals was observed via field emission scanning electron microscopy, and a quantitative elemental analysis was conducted via X-ray fluorescence spectrometry and energy dispersive X-ray analysis. The density and hardness of the WC hardmetals were respectively measured using an analytical balance and a Vikers hardness tester. The effect on the defects in the recycled WC hardmetals through the addition of the tungsten metal powder was discussed in detail.

Can oral rehydration solution be safely flavored at home?

PubMed

Nijssen-Jordan, C

1997-12-01

To determine the concentration of sodium, potassium, glucose, and osmolality of oral rehydration solutions (ORS) which have been flavored with varying amounts of unsweetened Kool-Aid powder, Jell-O powder, apple juice, or orange juice. Descriptive. Alberta Children's Hospital Chemistry Laboratory. None. Addition of varying amounts of flavoring easily available in all households to commercially available unsweetened ORS. Concentrations of electrolytes, glucose, and osmolality. Addition of fruit juices or flavor powders to commercially produced ORS does alter the electrolyte content and osmolality. When limited amounts of flavoring or juice is added, the osmolality of the solution approaches iso-osmolality. Small amounts of unsweetened Kool-Aid powder, Jell-O powder, and apple or orange juice can be added to oral rehydration solutions without significantly altering electrolyte composition and osmolality.

Effect of iron on the dissolution of bovine enamel powder in vitro by carbonated beverages.

PubMed

Kato, Melissa Thiemi; Maria, Andrea Gutierrez; Sales-Peres, Sílvia Helena de Carvalho; Buzalaf, Marília Afonso Rabelo

2007-07-01

The aim of this study was to evaluate, in vitro, the effect of iron on the dissolution of bovine enamel powder, when added to two carbonated beverages. Powdered enamel was produced by griding enamel fragments of bovine incisor in a steel pestle and mortar. Particles between 75 and 106 microm were selected using appropriated meshes. At time zero, the carbonated beverage (Coke or Sprite Zero) was added to powdered enamel (1 mg enamel powder/10 microL of beverage) and vortexed for 30 s. The sample was immediately centrifuged (11,000 rpm) for 30 s and the supernatant was removed at 1 min 40 s. This procedure was repeated five times with the beverage containing increasing ferrous sulphate concentrations (1.25, 2.5, 5, 10, 15, 30 and 60 mmol/L). The phosphate released in the medium was analysed spectrophotometrically. Data were analysed using ANOVA and Tukey's test (p<0.05). When iron at 30 and 60 mmol/L was added to Coke, a significant reduction in the dissolution of powdered enamel was observed when compared to control (11 and 17%, respectively), while lower iron concentrations did not have any effect on enamel powder dissolution. Regarding Sprite Zero, iron concentrations up to 10 mmol/L had no significant effect, while higher concentrations significantly increased enamel powder dissolution. The results suggest that iron can interfere with the dissolution of dental enamel powder in the presence of acidic beverages and the type of acid in these beverages seems to modulate this effect.

Composition and process for making an insulating refractory material

DOEpatents

Pearson, Alan; Swansiger, Thomas G.

1998-04-28

A composition and process for making an insulating refractory material. The composition includes calcined alumina powder, flash activated alumina powder, an organic polymeric binder and a liquid vehicle which is preferably water. Starch or modified starch may also be added. A preferred insulating refractory material made with the composition has a density of about 2.4-2.6 g/cm.sup.3 with reduced thermal conductivity, compared with tabular alumina. Of importance, the formulation has good abrasion resistance and crush strength during intermediate processing (commercial sintering) to attain full strength and refractoriness, good abrasion resistance and crush strength.

Application of zinc oxide quantum dots in food safety

USDA-ARS?s Scientific Manuscript database

Zinc oxide quantum dots (ZnO QDs) are nanoparticles of purified powdered ZnO. The ZnO QDs were directly added into liquid foods or coated on the surface of glass jars using polylactic acid (PLA) as a carrier. The antimicrobial activities of ZnO QDs against Listeria monocytogenes, Salmonella Enteriti...

Exploration on Wire Discharge Machining Added Powder for Metal-Based Diamond Grinding Wheel on Wire EDM Dressing and Truing of Grinding Tungsten Carbide Material

NASA Astrophysics Data System (ADS)

Chow, H. M.; Yang, L. D.; Lin, Y. C.; Lin, C. L.

2017-12-01

In this paper, the effects of material removal rate and abrasive grain protrusion on the metal-based diamond grinding wheel were studied to find the optimal parameters for adding powder and wire discharge. In addition, this kind of electric discharge method to add powder on the metal-based diamond grinding wheel on line after dressing and truing will be applied on tungsten carbide to study the grinding material removal rate, grinding wheel wear, surface roughness, and surface micro-hardness.

Bioactivity and mineralization of natural hydroxyapatite from cuttlefish bone and Bioglass® co-sintered bioceramics.

PubMed

Cozza, Natascia; Monte, Felipe; Bonani, Walter; Aswath, Pranesh; Motta, Antonella; Migliaresi, Claudio

2018-02-01

In this study, bioactive hydroxyapatite (HAP)-based bioceramics starting from cuttlefish bone powders have been prepared and characterized. In particular, fragmented cuttlefish bone was co-sintered with 30 wt% of Bioglass ® -45S5 to synthesize HAP-based powders with enhanced mechanical properties and bioactivity. Commercial synthetic HAP was treated following the same procedure and used as a reference. The structure and composition of the bioceramics formulations were characterized using Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscopy. After the thermal treatment of cuttlefish bone powder added with 30 wt% Bioglass, new phases with compositions of sodium calcium phosphate [Na 3 Ca 6 (PO 4 ) 5 ], β-tricalcium phosphate [Ca 3 (PO 4 )] and amorphous silica were detected. In vitro cell culture studies were performed by evaluating proliferation, metabolic activity and differentiation of human osteoblast-like cells (MG63). Scaffolds made with cuttlefish bone powder exhibited increased apatite deposition, alkaline phosphatase activity and cell proliferation compared with commercial synthetic HAP. In addition, the ceramic compositions obtained after the combination with Bioglass ® further enhanced the metabolic activity of MG63 cell and promoted the formation of a well-developed apatite layer after 7 days of incubation in Dulbecco's modified Eagle's medium. Copyright © 2017 John Wiley & Sons, Ltd.

Effect of starting powder morphology on film texture for bismuth layer-structured ferroelectrics prepared by aerosol deposition method

NASA Astrophysics Data System (ADS)

Suzuki, Muneyasu; Tsuchiya, Tetsuo; Akedo, Jun

2017-06-01

We report grain orientation control for bismuth layer-structured ferroelectrics (BLSFs) films deposited by aerosol deposition (AD) method at room temperature. Bi4Ti3O12 (BiT), SrBi2Ta2O9 (SBTa), and SrBi4Ti4O15 (SBTi) starting powders with particles of various shape (plate-like, spherical, and angular) were prepared by solid-state reaction and fused salt synthesis. Their AD films represented fine microstructures without pores, which agrees well with previous reports. Although the SBTa AD films deposited by using spherical particles exhibited an extremely low Lotgering factor (F), the BiT AD films deposited by using plate-like particles exhibited a marked c-axis orientation. The F of BiT and SBTi AD films decreased with increasing film thickness (t). We consider that the dispersion of agglomerated plate-like particles on the film surface and the densification of the compacted powder layer occurring while under particle impact are important in obtaining the grain-oriented AD films. These results of using the AD method with shape-controlled particles are expected to result in open up an innovative functional coating technique.

Development and optimization of iron- and zinc-containing nanostructured powders for nutritional applications.

PubMed

Hilty, F M; Teleki, A; Krumeich, F; Büchel, R; Hurrell, R F; Pratsinis, S E; Zimmermann, M B

2009-11-25

Reducing the size of low-solubility iron (Fe)-containing compounds to nanoscale has the potential to improve their bioavailability. Because Fe and zinc (Zn) deficiencies often coexist in populations, combined Fe/Zn-containing nanostructured compounds may be useful for nutritional applications. Such compounds are developed here and their solubility in dilute acid, a reliable indicator of iron bioavailability in humans, and sensory qualities in sensitive food matrices are investigated. Phosphates and oxides of Fe and atomically mixed Fe/Zn-containing (primarily ZnFe2O4) nanostructured powders were produced by flame spray pyrolysis (FSP). Chemical composition and surface area were systematically controlled by varying precursor concentration and feed rate during powder synthesis to increase solubility to the level of ferrous sulfate at maximum Fe and Zn content. Solubility of the nanostructured compounds was dependent on their particle size and crystallinity. The new nanostructured powders produced minimal color changes when added to dairy products containing chocolate or fruit compared to the changes produced when ferrous sulfate or ferrous fumarate were added to these foods. Flame-made Fe- and Fe/Zn-containing nanostructured powders have solubilities comparable to ferrous and Zn sulfate but may produce fewer color changes when added to difficult-to-fortify foods. Thus, these powders are promising for food fortification and other nutritional applications.

Utilization of squid pen for the efficient production of chitosanase and antioxidants through prolonged autoclave treatment.

PubMed

Wang, San-Lang; Wu, Pei-Chen; Liang, Tzu-Wen

2009-05-26

We have developed a culture system for efficient production of chitosanase by Bacillus sp. TKU004. TKU004 was cultivated by using squid pen powder as the sole carbon/nitrogen source. The effects of autoclave treatments of the medium on the production of chitosanase were investigated. Autoclave treatment of squid pen powder for 45 min remarkably promoted enzyme productivity. When the culture medium containing an initial squid pen powder concentration of 3% was autoclaved for 45 min, the chitosanase activity was optimal and reached 0.14-0.16 U/mL. In addition, extracellular surfactant-stable chitosanase was purified from the TKU004 culture supernatant. The antioxidant activity of TKU004 culture supernatant was determined through the scavenging ability of DPPH, with 70% per mL. With this method, we have shown that marine wastes can be utilized efficiently through prolonged autoclave treatments to generate a high value-added product, and have revealed its hidden potential in the production of functional foods.

Optimum carrageenan concentration improved the physical properties of cabinet-dried yoghurt powder

NASA Astrophysics Data System (ADS)

Pratama, Y.; Abduh, S. B. M.; Legowo, A. M.; Pramono, Y. B.; Albaarri, AN

2018-01-01

Carrageenan is a hydrocolloid which able to improve the characteristic of dried powder. The purpose of this study was to produce and evaluate the characteristics of yoghurt powder which incorporated carrageenan as stabilizer and dried in a cabinet dryer. Carrageenan of 1 %, 2 % and 3 % (w/v) concentration were added to yoghurt prior to cabinet drying process. Physical properties of the yoghurt powder and the reconstituted one were evaluated. The best result was shown in carrageenan concentration of 2 % where it showed the highest bulk density (0.62 g/ml), and best particle size distribution (65.49 % in the range of 250-500 μm). Moisture and water activity (aw) were 8.02% and 0.37, respectively. The value is lower than what spoilage microorganisms require to grow (aw > 0.6) thus ensuring its long shelf life when combined with proper packaging. Reconstitution at 50°C showed that 2 % carrageenan resulted in a stable yoghurt product with no visible syneresis even after 3 hours. The proposed method shows promising application in the production of long shelf-life yoghurt powder production.

Acoustic Properties of Polyurethane Composition Reinforced with Carbon Nanotubes and Silicon Oxide Nano-powder

NASA Astrophysics Data System (ADS)

Orfali, Wasim A.

This article demonstrates the acoustic properties of added small amount of carbon-nanotube and siliconoxide nano powder (S-type, P-Type) to the host material polyurethane composition. By adding CNT and/or nano-silica in the form of powder at different concentrations up to 2% within the PU composition to improve the sound absorption were investigated in the frequency range up to 1600 Hz. Sound transmission loss measurement of the samples were determined using large impedance tube. The tests showed that addition of 0.2 wt.% Silicon Oxide Nano-powder and 0.35 wt.% carbon nanotube to polyurethane composition improved sound transmissions loss (Sound Absorption) up to 80 dB than that of pure polyurethane foam sample.

Properties of zirconia-toughened-alumina prepared via powder processing and colloidal processing routes.

PubMed

Rafferty, A; Alsebaie, A M; Olabi, A G; Prescott, T

2009-01-15

Alumina-zirconia composites were prepared by two routes: powder processing, and colloidal processing. Unstabilised zirconia powder was added to alumina in 5 wt%, 10 wt% and 20 wt% quantities. For the colloidal method, zirconium(IV) propoxide solution was added to alumina powder, also in 5 wt%, 10 wt% and 20 wt% quantities. Additions of glacial acetic acid were needed to form stable suspensions. Suspension stability was verified by pH measurements and sedimentation testing. For the powder processed samples Vickers hardness decreased indefinitely with increasing ZrO(2) additions, but for colloidal samples the hardness at first decreased but then increased again above >10 wt% ZrO(2). Elastic modulus (E) values decreased with ZrO(2) additions. However, samples containing 20 wt% zirconia prepared via a colloidal method exhibited a much higher modulus than the powder processed equivalent. This was due to the homogeneous dispersion of zirconia yielding a sample which was less prone to microcracking.

The influence of Span-20 surfactant and micro-/nano-Chromium (Cr) Powder Mixed Electrical Discharge Machining (PMEDM) on the surface characteristics of AISI D2 hardened steel

NASA Astrophysics Data System (ADS)

Hosni, N. A. J.; Lajis, M. A.

2018-04-01

The application of powder mixed dielectric to improve the efficiency of electrical discharge machining (EDM) has been extensively studied. Therefore, PMEDM have attracted the attention of many researchers since last few decades. Improvement in EDM process has resulted in the use of span-20 surfactant and Cr powder mixed in dielectric fluid, which results in increasing machiniability, better surface quality and faster machining time. However, the study of powder suspension size of surface charateristics in EDM field is still limited. This paper presents the improvement of micro-/nano- Cr powder size on the surface characteristics of the AISI D2 hardened steels in PMEDM. It has found that the reacst layer in PMEDM improved by as high as 41-53 % compared to conventional EDM. Also notably, the combination of added Cr powder and span-20 surfactant reduced the recast layer thickness significantly especially in nano-Cr size. This improvement was great potential adding nano-size Cr powder to dielectric for machining performance.

Preparation of nano fluids by mechanical method

NASA Astrophysics Data System (ADS)

Boopathy, J.; Pari, R.; Kavitha, M.; Angelo, P. C.

2012-07-01

Nanofluids are conventional heat transfer fluids that contain nano particles of metals, oxides, carbides, nitrides, or nanotubes. Nanofluids exhibit enhanced thermal conductivity and heat transfer coefficients compared to the base fluids. This paper presents the procedure for preparing nanofluids consisting of Copper and Aluminium nano powders in base fluids. Copper and Aluminium nano powders were produced by planetary ball wet milling at 300rpm for 50hrs. Toluene was added to ensure wet milling. These powders were characterized in XRD and SEM for their purity, particle size and shape. The XRD results confirmed the final particle sizes of Copper and Aluminium in the nano range. Then the 0.01 gm of nano metal powders was added in 150 ml of double distilled water and magnetic stirring was done at 1500 rpm for 15 minutes. Sodium lauryl sulphate (0.05%) was added in water as surfactant to ensure the stability of the dispersion. Ultrasonication in the 3000 watts bath was done for 10 minutes to enhance the uniform dispersion of metal powders in water. The pH, dynamic viscosity, ionic conductivity and the stability of the fluids were determined for further usage of synthesized nanofluids as coolant during grinding operation.

An application of powder metallurgy to dentistry.

PubMed

Oda, Y; Ueno, S; Kudoh, Y

1995-11-01

Generally, the dental casting method is used to fabricate dental prostheses made with metal. The method of fabricating dental prostheses from sintered titanium alloy has certain advantages: the elimination of casting defects, a sintering temperature that is lower than the melting point, and a shorter processing time. By examining (1) the properties of green, sintered compacts of titanium powder, (2) the effects of adding aluminum powder on the properties of green, sintered compacts of Ti-Al compound, and (3) the effects of adding copper powder on the properties of green, sintered compacts of Ti-Al-Cu compound, the authors developed a sintered titanium alloy on a trial basis. Because the properties satisfied the requirements of dental restorations, a powder metallurgical method of making dental restorations from this sintered titanium alloy was devised. Applications of such sintered titanium alloys for the metal coping of metal-ceramic crowns and denture base plates were discussed.

A Self-Propagating Foaming Process of Porous Al-Ni Intermetallics Assisted by Combustion Reactions

PubMed Central

Kobashi, Makoto; Kanetake, Naoyuki

2009-01-01

The self-propagating foaming process of porous Al-Ni intermetallics was investigated. Aluminum and nickel powders were blended, and titanium and boron carbide powders were added as reactive exothermic agents. The blended powder was extruded to make a rod-shape precursor. Only one end of the rod precursor was heated to ignite the reaction. The reaction propagated spontaneously throughout the precursor. Pore formation took place at the same time as the reaction occurred. Adding the exothermic agent was effective to increase the porosity. Preheating the precursor before the ignition was also very effective to produce porous Al-Ni intermetallics with high porosity.

The use of atmospheric pressure plasma-treated water as a source of nitrite for emulsion-type sausage.

PubMed

Jung, Samooel; Kim, Hyun Joo; Park, Sanghoo; In Yong, Hae; Choe, Jun Ho; Jeon, Hee-Joon; Choe, Wonho; Jo, Cheorun

2015-10-01

We investigated the possible use of atmospheric pressure plasma-treated water (PTW) as a nitrite source in curing process. Emulsion-type sausages were manufactured with PTW, celery powder containing nitrite, and synthetic sodium nitrite at a concentration of nitrite ion 70mgkg(-1). In terms of sausage quality, there were no noticeable effects of PTW on the total aerobic bacterial counts, color, and peroxide values of sausages compared with those of celery powder and sodium nitrite throughout 28days of storage at 4°C. Sausage with added PTW had lower concentrations of residual nitrite compared to those of added celery powder and sodium nitrite during the storage period (P<0.05). The sensory properties of PTW-treated and sodium nitrite-treated sausages were not different, whereas the sausage with added celery powder received the lowest scores in taste and acceptability. From the results, it is concluded that PTW can be used as a nitrite source equivalent to a natural curing agent. Copyright © 2015 Elsevier Ltd. All rights reserved.

Nonaqueous solution synthesis process for preparing oxide powders of lead zirconate titanate and related materials

DOEpatents

Voigt, J.A.; Sipola, D.L.; Tuttle, B.A.; Anderson, M.T.

1999-06-01

A process is disclosed for producing powders of perovskite-type compounds which comprises mixing a metal alkoxide solution with a lead acetate solution to form a homogeneous, clear metal solution, adding an oxalic acid/n-propanol solution to this metal solution to form an easily filterable, free-flowing precursor powder and then calcining this powder. This process provides fine perovskite-phase powders with ferroelectric properties which are particularly useful in a variety of electronic applications. 4 figs.

Nonaqueous solution synthesis process for preparing oxide powders of lead zirconate titanate and related materials

DOEpatents

Voigt, James A.; Sipola, Diana L.; Tuttle, Bruce A.; Anderson, Mark T.

1999-01-01

A process for producing powders of perovskite-type compounds which comprises mixing a metal alkoxide solution with a lead acetate solution to form a homogeneous, clear metal solution, adding an oxalic acid/n-propanol solution to this metal solution to form an easily filterable, free-flowing precursor powder and then calcining this powder. This process provides fine perovskite-phase powders with ferroelectric properties which are particularly useful in a variety of electronic applications.

Mixing order of glidant and lubricant – Influence on powder and tablet properties

PubMed Central

Pingali, Kalyana; Mendez, Rafael; Lewis, Daniel; Michniak-Kohn, Bozena; Cuitino, Alberto; Muzzio, Fernando

2014-01-01

The main objective of the present work was to study the effect of mixing order of Cab-O-Sil (CS) and magnesium stearate (MgSt) and microlayers during mixing on blend and tablet properties. A first set of pharmaceutical blend containing Avicel PH200, Pharmatose and micronized acetaminophen was prepared with three mixing orders (mixing order-1: CS added first; mixing order-2: MgSt added first; mixing order-3: CS and MgSt added together). All the blends were subjected to a shear rate of 80 rpm and strain of 40, 160 and 640 revolutions in a controlled shear environment resulting in nine different blends. A second set of nine blends was prepared by replacing Avicel PH200 with Avicel PH102. A total of eighteen blends thus prepared were tested for powder hydrophobicity, powder flow, tablet weight, tablet hardness and tablet dissolution. Results indicated that powder hydrophobicity increased significantly for mixing order-1. Intermediate hydrophobic behavior was found for mixing order-3. Additionally, mixing order 1 resulted in improved powder flow properties, low weight variability, higher average tablet weight and slow drug release rates. Dissolution profiles obtained were found to be strongly dependent not only on the mixing order of flowing agents, but also on the strain and the resulting hydrophobicity. PMID:21356286

Calibration and testing of a Raman hyperspectral imaging system to reveal powdered food adulteration

USDA-ARS?s Scientific Manuscript database

The potential adulteration of foodstuffs has led to increasing concern regarding food safety and security, in particular for powdered food products where cheap ground materials or hazardous chemicals can be added to increase the quantity of powder or to obtain the desired aesthetic quality. Due to t...

The Effect of Oat Fibre Powder Particle Size on the Physical Properties of Wheat Bread Rolls

PubMed Central

Kurek, Marcin; Wyrwisz, Jarosław; Piwińska, Monika; Wierzbicka, Agnieszka

2016-01-01

Summary In response to the growing interest of modern society in functional food products, this study attempts to develop a bakery product with high dietary fibre content added in the form of an oat fibre powder. Oat fibre powder with particle sizes of 75 µm (OFP1) and 150 µm (OFP2) was used, substituting 4, 8, 12, 16 and 20% of the flour. The physical properties of the dough and the final bakery products were then measured. Results indicated that dough with added fibre had higher elasticity than the control group. The storage modulus values of dough with OFP1 most closely approximated those of the control group. The addition of OFP1 did not affect significantly the colour compared to the other samples. Increasing the proportion of oat fibre powder resulted in increased firmness, which was most prominent in wheat bread rolls with oat fibre powder of smaller particle sizes. The addition of oat fibre powder with smaller particles resulted in a product with the rheological and colour parameters that more closely resembled control sample. PMID:27904392

Antioxidant and anti-inflammatory activities of freeze-dried grapefruit phenolics as affected by gum arabic and bamboo fibre addition and microwave pretreatment.

PubMed

García-Martínez, Eva; Andújar, Isabel; Yuste Del Carmen, Alberto; Prohens, Jaime; Martínez-Navarrete, Nuria

2018-06-01

Recent epidemiological studies have suggested that phenolic compounds present in grapefruit play an important role in the bioactive properties of this fruit. However, the consumption of fresh grapefruit is low. Freeze-dried powdered grapefruit can be an alternative to promote this fruit consumption. To improve the quality and stability of the powdered fruit, encapsulating and anticaking agents can be added. In the present study, different grapefruit powders obtained by freeze-drying with the addition of gum arabic (1.27 g per 100 g) and bamboo fibre (0.76 g per 100 g) with and without a pre-drying microwave treatment were compared with the fresh and freeze-dried fruit with no carriers added, aiming to evaluate the effect of these preservation processes on phenolics content and on its antioxidant [1,1-diphenyl-2-picrylhydrazyl (DPPH), 2,2'-azinobis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) and ferric reducing ability of plasma (FRAP)] and anti-inflamatory (evaluated in RAW 264.7 macrophages) capacities. Freeze-drying and gum arabic and bamboo fibre addition significantly increased total phenolics, as well as the antioxidant and anti-inflammatory activities (by inhibiting nitric oxide production of lipopolysaccharide activated RAW 264.7 macrophages), of grapefruit. An additional increase in these parameters was obtained with microwave pretreatment before freeze-drying. The combined addition of gum arabic and bamboo fibre to grapefruit puree and the application of a microwave pretreatment improve the functional properties of the fruit without showing cytotoxicity in vitro. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Enhanced high-solids anaerobic digestion of waste activated sludge by the addition of scrap iron.

PubMed

Zhang, Yaobin; Feng, Yinghong; Yu, Qilin; Xu, Zibin; Quan, Xie

2014-05-01

Anaerobic digestion of waste activated sludge usually requires pretreatment procedure to improve the bioavailability of sludge, which involves considerable energy and high expenditures. This study proposes a cost-effective method for enhanced anaerobic digestion of sludge without a pretreatment by directly adding iron into the digester. The results showed that addition of Fe(0) powder could enhance 14.46% methane yield, and Fe scrap (clean scrap) could further enhance methane yield (improving rate 21.28%) because the scrap has better mass transfer efficiency with sludge and liquid than Fe(0) powder. The scrap of Fe with rust (rusty scrap) could induce microbial Fe(III) reduction, which resulted in achieving the highest methane yield (improving rate 29.51%), and the reduction rate of volatile suspended solids (VSS) was also highest (48.27%) among Fe powder, clean scrap and rusty scrap. PCR-DGGE proved that the addition of rusty scrap could enhance diversity of acetobacteria and enrich iron-reducing bacteria to enhance degradation of complex substrates. Copyright © 2014 Elsevier Ltd. All rights reserved.

Abrasion resistant coating and method of making the same

DOEpatents

Sordelet, Daniel J.; Besser, Matthew F.

2001-06-05

An abrasion resistant coating is created by adding a ductile phase to a brittle matrix phase during spray coating where an Al--Cu--Fe quasicrystalline phase (brittle matrix) and an FeAl intermetallic (ductile phase) are combined. This composite coating produces a coating mostly of quasicrystal phase and an inter-splat layer of the FeAl phase to help reduce porosity and cracking within the coating. Coatings are prepared by plasma spraying unblended and blended quasicrystal and intermetallic powders. The blended powders contain 1, 5, 10 and 20 volume percent of the intermetallic powders. The unblended powders are either 100 volume percent quasicrystalline or 100 volume percent intermetallic; these unblended powders were studied for comparison to the others. Sufficient ductile phase should be added to the brittle matrix to transform abrasive wear mode from brittle fracture to plastic deformation, while at the same time the hardness of the composite should not be reduced below that of the original brittle phase material.

Transglutaminase mediated microencapsulation of sea buckthorn supercritical CO2 extract in whey protein isolate and valorization in highly value added food products.

PubMed

Mihalcea, Liliana; Turturică, Mihaela; Barbu, Vasilica; Ioniţă, Elena; Pătraşcu, Livia; Cotârleţ, Mihaela; Dumitraşcu, Loredana; Aprodu, Iuliana; Râpeanu, Gabriela; Stănciuc, Nicoleta

2018-10-01

Sea buckthorn carotenoids extracted using CO 2 supercritical fluids method were encapsulated within whey proteins isolate by transglutaminase (TG) mediated crosslinking reaction, coacervation and freeze drying. The encapsulation efficiency was 36.23 ± 1.58%, with β-carotene the major carotenoid present in the powder. The confocal analysis revealed that TG-ase mediated cross-linking reaction enhanced the complexes stability to such a manner that a double microencapsulation was performed. The powder showed an antioxidant activity of 2.16 ± 0.14 mMol Trolox/g DW and an antifungal activity against Penicillium expansum MIUG M11. Four variants of domestic ice creams were obtained, with a total carotenoids content variation of 1.63 ± 0.03 mg/g D.W. in sample with 2% powder and 6.38 ± 0.04 mg/g D.W. in samples with 4% extract, having satisfactory antioxidant activity. The storage stability test showed a decrease in both total carotenoids content and antioxidant activity in all samples during 21 days at -18 °C. A protective effect of microencapsulation was evidenced. Copyright © 2018 Elsevier Ltd. All rights reserved.

Catalytic Graphitization for Preparation of Porous Carbon Material Derived from Bamboo Precursor and Performance as Electrode of Electrical Double-Layer Capacitor

NASA Astrophysics Data System (ADS)

Tsubota, Toshiki; Maguchi, Yuta; Kamimura, Sunao; Ohno, Teruhisa; Yasuoka, Takehiro; Nishida, Haruo

2015-12-01

The combination of addition of Fe (as a catalyst for graphitization) and CO2 activation (a kind of gaseous activation) was applied to prepare a porous carbon material from bamboo powder (a waste product of superheated steam treatment). Regardless of the heat treatment temperature, many macropores were successfully formed after the heating process by removal of Fe compounds. A turbostratic carbon structure was generated in the Fe-added sample heated at 850°C. It was confirmed that the added Fe acted as a template for pore formation. Moreover, it was confirmed that the added Fe acted as a catalyst for graphitization. The resulting electrochemical performance as the electrode of an electrical double-layer capacitor, as demonstrated by cyclic voltammetry, electrochemical impedance spectroscopy, and charge-discharge testing, could be explained based on the graphitization and activation effects. Addition of Fe could affect the electrical properties of carbon material derived from bamboo.

Preliminary report of the discovery of a new pharmaceutical granulation process using foamed aqueous binders.

PubMed

Keary, Colin M; Sheskey, Paul J

2004-09-01

Spray granulation is commonly used to improve the flow of drug formulation powders by adding liquid binders. We have discovered a new granulation process whereby liquid binders are added as aqueous foam. Initial experiments indicate that foam granulations require less binder than spray granulations, less water is added to the powder mass, rates of addition of foam can be greater than rates of addition of sprayed liquids, and foam can be added in a single batch to the surface of the powder mass for incorporation at some later stage in the process. This new process appears to have no detrimental effects on granulate, tablet, or in vitro drug dissolution properties. In addition, the elimination of spray addition reduces the complexity of the process and avoids the plugging problems associated with spray nozzles. Several formulations were successfully scaled up from laboratory scale (1.5 kg) to pilot scale (15 kg). Process control was good and there was no detrimental effect on tablet and drug dissolution properties. This paper also proposes a working hypothesis of the mechanism by which foam granulation operates.

Improvement of memory recall by quercetin in rodent contextual fear conditioning and human early-stage Alzheimer's disease patients.

PubMed

Nakagawa, Toshiyuki; Itoh, Masanori; Ohta, Kazunori; Hayashi, Yuichi; Hayakawa, Miki; Yamada, Yasushi; Akanabe, Hiroshi; Chikaishi, Tokio; Nakagawa, Kiyomi; Itoh, Yoshinori; Muro, Takato; Yanagida, Daisuke; Nakabayashi, Ryo; Mori, Tetsuya; Saito, Kazuki; Ohzawa, Kaori; Suzuki, Chihiro; Li, Shimo; Ueda, Masashi; Wang, Miao-Xing; Nishida, Emika; Islam, Saiful; Tana; Kobori, Masuko; Inuzuka, Takashi

2016-06-15

Patients with Alzheimer's disease (AD) experience a wide array of cognitive deficits, which typically include the impairment of explicit memory. In previous studies, the authors reported that a flavonoid, quercetin, reduces the expression of ATF4 and delays memory deterioration in an early-stage AD mouse model. In the present study, the effects of long-term quercetin intake on memory recall were assessed using contextual fear conditioning in aged wild-type mice. In addition, the present study examined whether memory recall was affected by the intake of quercetin-rich onion (a new cultivar of hybrid onion 'Quergold') powder in early-stage AD patients. In-vivo analysis indicated that memory recall was enhanced in aged mice fed a quercetin-containing diet. Memory recall in early-stage AD patients, determined using the Revised Hasegawa Dementia Scale, was significantly improved by the intake of quercetin-rich onion (Quergold) powder for 4 weeks compared with the intake of control onion ('Mashiro' white onion) powder. These results indicate that quercetin might influence memory recall.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peric, A.D.

Powder and granules of the high density polyethylene (PEHD) were used to prepare mortar based matrices for immobilization of radioactive waste materials containing {sup 137}Cs, as well as containers for solidified radioactive waste form. Seven types of matrices, differ due to the percentage of granules and filler material added, were investigated. PEHD powder and granules were added to mortar matrix preparations with the objective of improving physico-chemical characteristics of the radwaste-mortar matrix mixtures, in particular the leach-rate of the immobilized radionuclide, as well as mechanical characteristics either of mortar matrix and container. In this paper, only mechanical strength aspect ofmore » the investigated mortar and concrete container formulations, is presented. The equivalent diameter of the PEHD granules used was 2.0 mm. PEHD granules were used to replace 100 volume percent of stone granules, sifted size of 2.0 mm, normally used in the matrix preparation, in order to decrease the porosity and density of the mortar matrix and to avoid segregation of the stone particles at the bottom of the immobilized radioactive waste cylindrical form. PEHD powder, particle size of 250 micrometer, was added as filler to the mortar formulation, replacing 5, 8 and 10 wt% of the total cement weight in matrix formulation and 15 and 18 wt% of the total cement weight in container formulation. Cured samples were investigated on mechanical strength, using 150 MPa hydraulic press, in order to determine influence of added polyethylene granules and powder on samples resistance to mechanical forces that solidified waste materials and concrete containers may experience at the disposal site. Results of performed investigations have shown that samples prepared with polyethylene granules, replacing 100 wt% of the stone granules, have almost twice as much mechanical strength than samples prepared with stone aggregate. Samples prepared with PEHD granules and powder have mechanical strength resistance up to 13.5% higher than ones prepared with PEHD granules, solely. Improved Mechanical strength resistance of tested samples accommodates trend that functionally depends on the percentage of PEHD powder added in formulation.« less

Single Crystal Growth of Zirconia Utilizing a Skull Melting Technique,

DTIC Science & Technology

1979-08-01

23 REFERENCES 24 Illustrations 1. Cutaway View of Skull Crucible 11 2. Section View of Skull Crucible 11 3. Stabilized Zirconia Powder Being Added to...E. R., (1968) J. Cryst. Growth, 2:243. 11 ... . . l l&I. .. . .:. . . N ’ - . . . . . . i . . . . . . . . .: P Figure 3. Stabilized Zirconia Powder Figure...colorless. The zirconia powder used in these experiments was obtained from N. L. Industries, Inc. Samples of the powder with 25 weight percent Y 2 0 3

The use of whey or skimmed milk powder in fortified blended foods for vulnerable groups.

PubMed

Hoppe, Camilla; Andersen, Gregers S; Jacobsen, Stine; Mølgaard, Christian; Friis, Henrik; Sangild, Per T; Michaelsen, Kim F

2008-01-01

Fortified blended foods (FBF), especially corn soy blend, are used as food aid for millions of people worldwide, especially malnourished individuals and vulnerable groups. There are only a few studies evaluating the effect of FBF on health outcomes, and the potential negative effect of antinutrients has not been examined. Different lines of evidence suggest that dairy proteins have beneficial effects on vulnerable groups. Here we review the evidence on the effects of adding whey or skimmed milk powder to FBF used for malnourished infants and young children or people living with HIV or AIDS. Adding whey or skimmed milk powder to FBF improves the protein quality, allowing a reduction in total amount of protein, which could have potential metabolic advantages. It also allows for a reduced content of soy and cereal and thereby a reduction of potential antinutrients. It is possible that adding milk could improve weight gain, linear growth, and recovery from malnutrition, but this needs to be confirmed. Bioactive factors in whey might have beneficial effects on the immune system and muscle synthesis, but evidence from vulnerable groups is lacking. Milk proteins will improve flavor, which is important for acceptability in vulnerable groups. The most important disadvantage is a considerable increase in price. Adding 10-15% milk powder would double the price, which means that such a product should be used only in well-defined vulnerable groups with special needs. The potential beneficial effects of adding milk protein and lack of evidence in vulnerable groups call for randomized intervention studies.

Effects of milk powder and its components on texture, yield, and color of a lean poultry meat model system.

PubMed

Barbut, S

2010-06-01

The effects of whole milk powder, 2 skim milk powders, caseinate, and 2 modified whey proteins (2% protein level in the final product) were evaluated in lean chicken meat batters and compared with controls with and without added lactose. All dairy proteins significantly (P<0.05) reduced cook losses when compared against the controls, with the 2 skim milk powders and modified whey-I showing the best results. Hardness and fracturability were also higher for all test batters compared with controls. Skim milk-II showed the highest fracturability value (21.9 vs. 7.1 N for the control) and was also found to be the most cost-effective ingredient for improving moisture binding and texture; skim milk-I and modified whey-I followed behind. Springiness and fracture distance were higher for all of the dairy proteins, except caseinate, indicating a positive contribution to the lean meat system's elasticity. In terms of color, adding the skim milk powders, modified whey-II, and whole milk powder resulted in lighter cooked meat batters as evidenced by the higher L* values and higher spectra curves.

Method for producing microcomposite powders using a soap solution

DOEpatents

Maginnis, Michael A.; Robinson, David A.

1996-01-01

A method for producing microcomposite powders for use in superconducting and non-superconducting applications. A particular method to produce microcomposite powders for use in superconducting applications includes the steps of: (a) preparing a solution including ammonium soap; (b) dissolving a preselected amount of a soluble metallic such as silver nitrate in the solution including ammonium soap to form a first solution; (c) adding a primary phase material such as a single phase YBC superconducting material in particle form to the first solution; (d) preparing a second solution formed from a mixture of a weak acid and an alkyl-mono-ether; (e) adding the second solution to the first solution to form a resultant mixture; (f) allowing the resultant mixture to set until the resultant mixture begins to cloud and thicken into a gel precipitating around individual particles of the primary phase material; (g) thereafter drying the resultant mixture to form a YBC superconducting material/silver nitrate precursor powder; and (h) calcining the YBC superconducting material/silver nitrate precursor powder to convert the silver nitrate to silver and thereby form a YBC/silver microcomposite powder wherein the silver is substantially uniformly dispersed in the matrix of the YBC material.

The Use of Tomato Powder Fermented with Pediococcus pentosaceus and Lactobacillus sakei for the Ready-to-Cook Minced Meat Quality Improvement

PubMed Central

Juodeikiene, Grazina; Zadeike, Daiva; Viskelis, Pranas; Urbonaviciene, Dalia

2015-01-01

Summary In this study, the influence of lactic acid fermentation on the quality of tomato powder was evaluated. The effect of adding fermented tomato powder to ready-to-cook minced pork meat to improve its nutritional value and sensory characteristics was also analysed. The cell growth of Lactobacillus sakei (7.53 log CFU/g) was more intense in the medium containing tomato powder, compared to the growth of Pediococcus pentosaceus (6.35 log CFU/g) during 24 h of fermentation; however, higher acidity (pH=4.1) was observed in the tomato powder samples fermented with Pediococcus pentosaceus. The spontaneous fermentation of tomato powder reduced cell growth by 38% and pH values slightly increased to 4.17, compared to the fermentation with pure LAB. The lactofermentation of tomato powder increased the average β-carotene and lycopene mass fractions by 43.9 and 50.2%, respectively, compared with the nonfermented samples. Lycopene and β-carotene contents in the ready-to-cook minced pork meat were proportional to the added tomato powder (10 and 30%). After cooking, β-carotene and lycopene contents decreased, on average, by 24.2 and 41.2%, respectively. The highest loss (up to 49.2%) of carotenoids was found in samples with 30% nonfermented tomato powder. Tomato powder fermented with 10% Lactobacillus sakei KTU05-6 can be recommended as both a colouring agent and a source of lycopene in the preparation of ready-to-cook minced pork meat. PMID:27904345

Reutilization of granite powder as an amendment and fertilizer for acid soils.

PubMed

Barral Silva, M T; Silva Hermo, B; García-Rodeja, E; Vázquez Freire, N

2005-11-01

The properties of granite powders--a granite manufacturing waste product-were analyzed to assess their potential use as amendments and fertilizers on acid soils. Two types of powders were characterized: one produced during cutting of granite with a diamond-edged disc saw, comprising only rock powder, the other produced during cutting with a multi-blade bandsaw, containing calcium hydroxide and metal filings added during the cutting procedure. The acid neutralizing capacity of the granite powders was assessed in short- (2-3 h) and medium-term (1-30 d) experiments. The powders showed a buffering capacity at around pH 8, which corresponded to the rapid dissolution of basic cations, and another buffering effect at pH<4.5, attributable to the dissolution of Fe and Al. The acid neutralizing capacity (ANC) determined in the short-term experiments, to a final pH of 4.5, varied between 5 and 61 cmol H+kg(-1) powder. The ANC to pH 4.5 obtained in the medium-term experiments was much higher than that obtained in the short-term experiments, reaching a maximum ANC value of 200 cmol H+kg(-1) powder. There was no great difference in the neutralizing capacity determined at between 1 and 30 d. The most abundant elements in acid solutions obtained at the end of medium-term experiments were Mg and Ca for disc saw powders, whereas Ca and Fe (at pH<5) were the most soluble elements in the bandsaw powders. The rapid release of these cations suggests the possible effective use of the granite powders as a source of nutrients on being added to acid soils.

Effects of amaranth addition on the pro-vitamin A content, and physical and antioxidant properties of extruded pro-vitamin A-biofortified maize snacks.

PubMed

Beswa, Daniso; Dlamini, Nomusa R; Amonsou, Eric O; Siwela, Muthulisi; Derera, John

2016-01-15

Pro-vitamin A-biofortified maize snacks with added leafy vegetable may have a potential as nutritious and health-promoting products, especially in addressing vitamin A deficiency, which is prevalent in developing regions. The objective of the study was to determine the effects of adding amaranth leaf powder on the physical, antioxidant properties and pro-vitamin A content of extruded pro-vitamin A-biofortified maize snacks. Extruded snacks were processed using four pro-vitamin A-biofortified maize varieties that were composited with amaranth leaf powder at 0%, 1% and 3% (w/w) substitution levels. At higher amaranth concentration, the expansion ratio of the snacks decreased, while their hardness increased by as much as 93%. The physical quality of the snacks may therefore need improvement. As amaranth was increased, the phenolic content and antioxidant activity of the snacks increased as well as the pro-vitamin A content. Pro-vitamin A-biofortified maize with added amaranth has a potential for use in nutritious and healthy extruded snacks. There are limited studies reporting on processing pro-vitamin A maize with complementary plant foods, which is common with white maize in southern Africa; thus the current study serves as a baseline. © 2015 Society of Chemical Industry.

Theoretical considerations for Reaction-Formed Silicon Carbide (RFSC) formation by molten silicon infiltration into slurry-derived preforms

NASA Technical Reports Server (NTRS)

Behrendt, D. R.; Singh, M.

1993-01-01

For reaction-formed silicon carbide (RFSC) ceramics produced by silicon melt infiltration of porous carbon preforms, equations are developed to relate the amount of residual silicon to the initial carbon density. Also, for a slurry derived preform containing both carbon and silicon powder, equations are derived which relate the amount of residual silicon in the RFSC to the relative density of the carbon in the preform and to the amount of silicon powder added to the slurry. For a porous carbon preform that does not have enough porosity to prevent choking-off of the silicon infiltration, these results show that complete silicon infiltration can occur by adding silicon powder to the slurry mixture used to produce these preforms.

Modifications of fatty acids profile, lipid peroxidation and antioxidant capacity in raw and cooked rabbit burgers added with ginger.

PubMed

Mancini, Simone; Preziuso, Giovanna; Dal Bosco, Alessandro; Roscini, Valentina; Parisi, Giuliana; Paci, Gisella

2017-11-01

Effects of ginger powder were evaluated on fatty acid (FA) profile, lipid peroxidation (TBARS) and antioxidant capacity (ABTS, DPPH and FRAP) of rabbit burgers. Burgers were manufactured as control samples (only meat) and two additions of ginger powder (1% and 2%) and stored raw at 4°C for 7days. At day 1, 4 and 7 of storage burgers were analysed both as raw and cooked. Ginger powder affected all the tested parameters; both PUFAω3 and PUFAω6 were incremented in raw and cooked samples leading to decreased atherogenicity and thrombogenicity indexes and increased hypo/hypercholesterolemic index and peroxidability index. Lipid peroxidation values of raw and cooked burgers added with ginger were lower than control burgers, at the same time, ABTS, DPPH and FRAP values were incremented by the addition of ginger powder. The results obtained demonstrate the antioxidant capacity of ginger powder as rabbit meat products additive and highlight the capacity of this spice to maintain its characteristics after burgers' cooking. Copyright © 2017 Elsevier Ltd. All rights reserved.

The influence of iron oxide nanoparticles upon the adsorption of organic matter on magnetic powdered activated carbon.

PubMed

Lompe, Kim Maren; Menard, David; Barbeau, Benoit

2017-10-15

Combining powdered activated carbon (PAC) with magnetic iron oxides has been proposed in the past to produce adsorbents for natural organic matter (NOM) removal that can be easily separated using a magnetic field. However, the trade-off between the iron oxides' benefits and the reduced carbon content, porosity, and surface area has not yet been investigated systematically. We produced 3 magnetic powdered activated carbons (MPAC) with mass fractions of 10%, 38% and 54% maghemite nanoparticles and compared them to bare PAC and pure nanoparticles with respect to NOM adsorption kinetics and isotherms. While adsorption kinetics were not influenced by the presence of the iron oxide nanoparticles (IONP), as shown by calculated diffusion coefficients from the homogeneous surface diffusion model, nanoparticles reduced the adsorption capacity of NOM due to their lower adsorption capacity. Although the nanoparticles added mesoporosity to the composite materials they blocked intrinsic PAC mesopores at mass fractions >38% as measured by N 2 -adsorption isotherms. Below this mass fraction, the adsorption capacity was mainly dependent on the carbon content in MPAC and mesopore blocking was negligible. If NOM adsorption with MPAC is desired, a highly mesoporous PAC and a low IONP mass fraction should be chosen during MPAC synthesis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Polyfibroblast: A Self-Healing and Galvanic Protection Additive

DTIC Science & Technology

2012-09-12

self-healing and galvanic protection capacity to the primer (Figure 1). Polyfibroblast consists of paint-filled microcapsules and zinc powder. It has...significant added cost. Microcapsule Figure 1. Polyfibroblast contains fresh paint encapsulated in polymer shells plus Zn powder. When scratched, resin...from the broken microcapsules fills the crack to form a polymer scar. Zn powder supplies galvanic protection in the event of incomplete healing

Effects of adding red wine on the physicochemical properties and sensory characteristics of uncured frankfurter-type sausage.

PubMed

Feng, Xi; Sebranek, Joseph G; Lee, Hyun Yong; Ahn, Dong Uk

2016-11-01

The aim of this work was to evaluate the quality and sensory characteristics of RTE frankfurter-type sausage cured with celery juice powder and including red wine. Four frankfurter treatments including a conventionally cured treatment without red wine (control) and three treatments cured with pre-converted vegetable juice powder and 0%, 5% or 10% (v/w) red wine were prepared. Results showed that adding 5% red wine increased the a*-value, and the textural resilience, cohesiveness and springiness of the frankfurters, as well as decreased lipid/protein oxidation of the final products. Added wine also introduced new volatiles (alcohol and ester compounds) to the frankfurters. The principal component (PC) analysis showed that the pre-converted vegetable juice powder achieved the same effects as the conventional curing agents for typical frankfurter properties. However, the addition of excess amounts of red wine (10%) to the meat batter decreased the pH of meat batter and accelerated lipid oxidation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Larnite powders and larnite/silica aerogel composites as effective agents for CO2 sequestration by carbonation.

PubMed

Santos, A; Ajbary, M; Morales-Flórez, V; Kherbeche, A; Piñero, M; Esquivias, L

2009-09-15

This paper presents the results of the carbonation reaction of two sample types: larnite (Ca(2)SiO(4)) powders and larnite/silica aerogel composites, the larnite acting as an active phase in a process of direct mineral carbonation. First, larnite powders were synthesized by the reaction of colloidal silica and calcium nitrate in the presence of ethylene glycol. Then, to synthesize the composites, the surface of the larnite powders was chemically modified with 3-aminopropyltriethoxysilane (APTES), and later this mixture was added to a silica sol previously prepared from tetraethylorthosilicate (TEOS). The resulting humid gel was dried in an autoclave under supercritical conditions for the ethanol. The textures and chemical compositions of the powders and composites were characterized.The carbonation reaction of both types of samples was evaluated by means of X-ray diffraction and thermogravimetric analysis. Both techniques confirm the high efficiency of the reaction at room temperature and atmospheric pressure. A complete transformation of the silicate into carbonate resulted after submitting the samples to a flow of pure CO(2) for 15 min. This indicates that for this reaction time, 1t of larnite could eliminate about 550 kg of CO(2). The grain size, porosity, and specific surface area are the factors controlling the reaction.

Supplementation of the Diet by Exogenous Myrosinase via Mustard Seeds to Increase the Bioavailability of Sulforaphane in Healthy Human Subjects After the Consumption of Cooked Broccoli.

PubMed

Okunade, Olukayode; Niranjan, Keshavan; Ghawi, Sameer K; Kuhnle, Gunter; Methven, Lisa

2018-05-28

Broccoli contains the glucosinolate glucoraphanin which, in the presence of myrosinase, can hydrolyse to the isothiocyanate sulforaphane, reported to have anti-carcinogenic activity. However, the myrosinase enzyme is denatured on cooking. Addition of an active source of myrosinase, such as from powdered mustard seed, to cooked brassica vegetables can increase the release of health beneficial isothiocyanates, however this has not previously been proven in-vivo. The concentration of sulforaphane metabolite (sulforaphane N-acetyl-L-cysteine (SF-NAC) in 12 healthy adults after the consumption of 200g cooked broccoli, with and without 1 g powdered brown mustard, was studied in a randomized crossover design. During the 24 hour period following consumption of the study sample all urine was collected. SF-NAC content was assayed by HPLC. When study subjects ingested cooked broccoli alone, mean urinary SF-NAC excreted was 9.8 ± 5.1 μmol per g creatinine, whilst when cooked broccoli was consumed with mustard powder this increased significantly to 44.7 ± 33.9 μmol SF-NAC per g creatinine. These results conclude that when powdered brown mustard is added to cooked broccoli the bioavailability of sulforaphane is over four times greater than that from cooked broccoli ingested alone. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Lotus (Nelumbo nucifera) Rhizome as an Antioxidant Dietary Fiber in Cooked Sausage: Effects on Physicochemical and Sensory Characteristics.

PubMed

Ham, Youn-Kyung; Hwang, Ko-Eun; Song, Dong-Heon; Kim, Yong-Jae; Shin, Dong-Jin; Kim, Kyung-Il; Lee, Hye-Jin; Kim, Na-Rae; Kim, Cheon-Jei

2017-01-01

The objective of this study was to determine the physicochemical and sensory properties of cooked emulsion sausages containing different levels of lotus rhizome powder (0, 1, 2, and 3%, based on total weight). Lotus rhizome powder had no significant ( p >0.05) impact on pH, moisture, protein, or ash content of sausage. However, fat content was slightly but significantly ( p <0.05) decreased when the level of lotus rhizome powder was increased in the sausages. The addition of lotus rhizome powder to sausages at over 1% resulted in significantly ( p <0.05) darker and less red color of cooked sausage compared to control. Increase in lotus rhizome level slightly improved the emulsion stability and apparent viscosity. Significant ( p <0.05) reduction in cooking loss was observed when more than 1% of lotus rhizome powder was added to sausages. The textural properties of sausages were unaffected by the inclusion of lotus rhizome except for springiness and chewiness. On the manufacture day, control sausage had significantly ( p <0.05) higher TBARS value than treatments. Regarding sensory characteristics, increased levels of lotus rhizome powder decreased ( p <0.05) color and juiciness scores. However, cooked sausages exhibited similar overall acceptability regardless of the level of lotus rhizome powder added to sausages. Therefore, lotus rhizome powder, an antioxidant dietary fiber, could be used as an effective natural ingredient in meat products for the development of healthier and functional food.

Lotus (Nelumbo nucifera) Rhizome as an Antioxidant Dietary Fiber in Cooked Sausage: Effects on Physicochemical and Sensory Characteristics

PubMed Central

2017-01-01

The objective of this study was to determine the physicochemical and sensory properties of cooked emulsion sausages containing different levels of lotus rhizome powder (0, 1, 2, and 3%, based on total weight). Lotus rhizome powder had no significant (p>0.05) impact on pH, moisture, protein, or ash content of sausage. However, fat content was slightly but significantly (p<0.05) decreased when the level of lotus rhizome powder was increased in the sausages. The addition of lotus rhizome powder to sausages at over 1% resulted in significantly (p<0.05) darker and less red color of cooked sausage compared to control. Increase in lotus rhizome level slightly improved the emulsion stability and apparent viscosity. Significant (p<0.05) reduction in cooking loss was observed when more than 1% of lotus rhizome powder was added to sausages. The textural properties of sausages were unaffected by the inclusion of lotus rhizome except for springiness and chewiness. On the manufacture day, control sausage had significantly (p<0.05) higher TBARS value than treatments. Regarding sensory characteristics, increased levels of lotus rhizome powder decreased (p<0.05) color and juiciness scores. However, cooked sausages exhibited similar overall acceptability regardless of the level of lotus rhizome powder added to sausages. Therefore, lotus rhizome powder, an antioxidant dietary fiber, could be used as an effective natural ingredient in meat products for the development of healthier and functional food. PMID:28515646

Activity of Fosfomycin- and Daptomycin-Containing Bone Cement on Selected Bacterial Species Being Associated with Orthopedic Infections.

PubMed

Eick, Sigrun; Hofpeter, Kevin; Sculean, Anton; Ender, Claudia; Klimas, Susann; Vogt, Sebastian; Nietzsche, Sandor

2017-01-01

The purpose of this study was to determine activity of fosfomycin/gentamicin and daptomycin/gentamicin-containing PMMA bone-cement against Staphylococcus aureus (MRSA, MSSA), Staphylococcus epidermidis , Enterococcus faecium (VRE), and E. coli (ESBL; only fosfomycin). Test specimens of the bone cement were formed and bacteria in two concentrations were added one time or repeatedly up to 96 h. All fosfomycin-containing cement killed ultimately all MSSA, Staphylococcus epidermidis, and E. coli within 24 h; growth of MRSA was suppressed up to 48 h. Activity of daptomycin-containing cement depended on the concentration; the highest concentrated bone cement used (1.5 g daptomycin/40 g of powder) was active against all one-time added bacteria. When bacteria were added repeatedly to fosfomycin-containing cement, growth was suppressed up to 96 h and that of MRSA and VRE only up to 24 h. The highest concentration of daptomycin suppressed the growth of repeated added bacteria up to 48 h (VRE) until 96 h (MSSA, MRSA). In conclusion, PMMA bone cement with 1.5 g of daptomycin and 0.5 g of gentamicin may be an alternative in treatment of periprosthetic infections caused by Gram-positive bacteria.

Activity of Fosfomycin- and Daptomycin-Containing Bone Cement on Selected Bacterial Species Being Associated with Orthopedic Infections

PubMed Central

Hofpeter, Kevin; Sculean, Anton; Ender, Claudia; Klimas, Susann; Vogt, Sebastian; Nietzsche, Sandor

2017-01-01

The purpose of this study was to determine activity of fosfomycin/gentamicin and daptomycin/gentamicin-containing PMMA bone-cement against Staphylococcus aureus (MRSA, MSSA), Staphylococcus epidermidis, Enterococcus faecium (VRE), and E. coli (ESBL; only fosfomycin). Test specimens of the bone cement were formed and bacteria in two concentrations were added one time or repeatedly up to 96 h. All fosfomycin-containing cement killed ultimately all MSSA, Staphylococcus epidermidis, and E. coli within 24 h; growth of MRSA was suppressed up to 48 h. Activity of daptomycin-containing cement depended on the concentration; the highest concentrated bone cement used (1.5 g daptomycin/40 g of powder) was active against all one-time added bacteria. When bacteria were added repeatedly to fosfomycin-containing cement, growth was suppressed up to 96 h and that of MRSA and VRE only up to 24 h. The highest concentration of daptomycin suppressed the growth of repeated added bacteria up to 48 h (VRE) until 96 h (MSSA, MRSA). In conclusion, PMMA bone cement with 1.5 g of daptomycin and 0.5 g of gentamicin may be an alternative in treatment of periprosthetic infections caused by Gram-positive bacteria. PMID:28484708

Entrainment of lactose inhalation powders: a study using laser diffraction.

PubMed

Watling, C P; Elliott, J A; Cameron, R E

2010-07-11

We have investigated the mechanism of entrainment of lactose inhalation blends released from a dry powder inhaler using a diffraction particle size analyser (Malvern Spraytec). Whether a powder blend entrains as a constant stream of powder (the "erosion" mechanism) or as a few coarse plugs (the "fracture" mechanism) was found by comparing transmission data with particle size information. This technique was then applied to a lactose grade with 0, 5 and 10wt% added fine particles. As the wt% fines increased, the entrainment mechanism was found to change from a mild fracture, consisting of multiple small plugs, to more severe fracture with fewer plugs. The most severe fracture mechanism consisted of either the powder reservoir emptying as a single plug, or of the reservoir emptying after a delay of the order of 0.1s due to the powder sticking to its surroundings. Further to this, three different inhalation grades were compared, and the severity of the fracture was found to be inversely proportional to the flowability of the powder (measured using an annular ring shear tester). By considering the volume of aerosolised fine particles in different blends it was determined that the greater the volume of fines added to a powder, the smaller the fraction of fines that were aerosolised. This was attributed to different behaviour when fines disperse from carrier particles compared with when they disperse from agglomerates of fines. In summary, this paper demonstrates how laser diffraction can provide a more detailed analysis of an inhalation powder than just its size distribution. 2010. Published by Elsevier B.V. All rights reserved.

Characterization of geopolymer fly-ash based foams obtained with the addition of Al powder or H{sub 2}O{sub 2} as foaming agents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ducman, V., E-mail: vilma.ducman@zag.si; Korat, L.

Recent innovations in geopolymer technology have led to the development of various different types of geopolymeric products, including highly porous geopolymer-based foams, which are formed by the addition of foaming agents to a geopolymer fly-ash based matrix. These agents decompose, or react with the liquid matrix or oxygen in the matrix, resulting in the release of gases which form pores prior to the hardening of the gel. The hardened structure has good mechanical and thermal properties, and can therefore be used for applications in acoustic panels and in lightweight pre-fabricated components for thermal insulation purposes. This study presents the resultsmore » of the pore-forming process in the case when two different foaming agents, i.e. aluminium powder amounting to 0.07, 0.13 and 0.20 mass. % and H{sub 2}O{sub 2} amounting to 0.5, 1.0, 1.5 and 2.0 mass. %, were added to a fly-ash geopolymer matrix. The physical, mechanical, and microstructural properties of the thus obtained foams, and the effects of the type and amount of the added foaming agent, are presented and discussed. Highly porous structures were obtained in the case of both of the investigated foaming agents, with overall porosities up to 59% when aluminium powder was added, and of up 48% when H{sub 2}O{sub 2} was added. In the latter case, when 2% of the H{sub 2}O{sub 2} foaming agent was added, finer pores (with diameters up to 500 μm) occurred in the structure, whereas somewhat larger pores (some had diameters greater than 1 mm) occurred when the same amount of aluminium powder was added. The mechanical properties of the investigated foams depended on their porosity. In the case of highly porous structures a compressive strength of 3.3 MPa was nevertheless achieved for the samples containing 0.2% of aluminium powder, and 3.7 MPa for those containing 2.0% of H{sub 2}O{sub 2}. - Highlights: • Preparation of geopolymer foams based on fly ash with the addition of Al powder or H{sub 2}O{sub 2} as foaming agents • Determination of density, porosity and mechanical properties of such foams • Characterization of foaming process by means of X-ray micro-tomography (μcT)« less

PPARgamma agonist curcumin reduces the amyloid-beta-stimulated inflammatory responses in primary astrocytes.

PubMed

Wang, Hong-Mei; Zhao, Yan-Xin; Zhang, Shi; Liu, Gui-Dong; Kang, Wen-Yan; Tang, Hui-Dong; Ding, Jian-Qing; Chen, Sheng-Di

2010-01-01

Alzheimer's disease (AD) is the most common age-related neurodegenerative disorder. Accumulating data indicate that astrocytes play an important role in the neuroinflammation related to the pathogenesis of AD. It has been shown that microglia and astrocytes are activated in AD brain and amyloid-beta (Abeta) can increase the expression of cyclooxygenase 2 (COX-2), interleukin-1, and interleukin-6. Suppressing the inflammatory response caused by activated astrocytes may help to inhibit the development of AD. Curcumin is a major constituent of the yellow curry spice turmeric and proved to be a potential anti-inflammatory drug in arthritis and colitis. There is a low age-adjusted prevalence of AD in India, a country where turmeric powder is commonly used as a culinary compound. Curcumin has been shown to suppress activated astroglia in amyloid-beta protein precursor transgenic mice. The real mechanism by which curcumin inhibits activated astroglia is poorly understood. Here we report that the expression of COX-2 and glial fibrillary acidic protein were enhanced and that of peroxisome proliferator-activated receptor gamma (PPARgamma) was decreased in Abeta(25-35)-treated astrocytes. In line with these results, nuclear factor-kappaB translocation was increased in the presence of Abeta. All these can be reversed by the pretreatment of curcumin. Furthermore, GW9662, a PPARgamma antagonist, can abolish the anti-inflammatory effect of curcumin. These results show that curcumin might act as a PPARgamma agonist to inhibit the inflammation in Abeta-treated astrocytes.

Effect of milling time and annealing temperature on nanoparticles evolution for 13.5% Cr ODS ferritic steel powders by joint application of XAFS and TEM

NASA Astrophysics Data System (ADS)

He, P.; Hoffmann, J.; Möslang, A.

2018-04-01

The characteristics of strengthening nanoparticles have a major influence on the mechanical property and irradiation resistance of oxide dispersion strengthened (ODS) steels. To determine how to control nanoparticles evolution, 0.3% Ti with 0.3% Y2O3 were added in 13.5%Cr pre-alloyed steel powders via different milling and consolidation conditions, then characterized by transmission electron microscopy (TEM) and X-ray absorption fine structure (XAFS) at synchrotron irradiation facility. The dissolution of Y2O3 is greatly dependent on the milling time at fixed milling speeds. After 24 h of milling, only minor amounts of the initially added Y2O3 dissolve into the steel matrix whereas TEM results reveal nearly complete dissolution of Y2O3 in 80-h-milled powder. The annealed powder FT-A800 (at 800 °C for 1 h) exhibits a structure near to the initially added Y2O3. The slightly deviation may be accounted for considerable lattice distortion related to the presence of atomic vacancies or formation of Y-Ti-O nucleus. The annealed powders FT-A1000 and FT-A1100 contain complex mixtures of Y-O/Y-Ti-O oxides, which cannot be fitted by any single thermally stable compounds. The coordination numbers of these first two shells in the annealed powders significantly raise as a function of the annealing temperature, indicating the formation of more ordered Y-O or Y-Ti-O particles. The extended X-ray absorption fine structure (EXAFS) spectrum could not necessarily distinguish the dominant oxide species.

JPRS Report, Science & Technology, Japan, 28th Ceramics Science Discussion

DTIC Science & Technology

1990-11-13

U non doped "5 Ag powder A 60 120 180 140 300 Temperature (K) Figure 1. Plots or Resistivity Vs. Temperature for YBa 2 Cu 30Y to Which Different...Yasuharu Kodama, et al.] ........................ 13 -a - Superplasticity of Hydroxyapatite [Fumihiro Wakai, Yasuharu Kodama, et al...67 Synthesis of Ag -Added Bi-Pb-Ca-Cu-O Powder by Spray Drying, Superconductivity of Powder [Hiroko Higuma, Mitsunobu Wakata, et al

PVC-based composite material containing recycled non-metallic printed circuit board (PCB) powders.

PubMed

Wang, Xinjie; Guo, Yuwen; Liu, Jingyang; Qiao, Qi; Liang, Jijun

2010-12-01

The study is directed to the use of non-metallic powders obtained from comminuted recycled paper-based printed circuit boards (PCBs) as an additive to polyvinyl chloride (PVC) substrate. The physical properties of the non-metallic PCB (NMPCB) powders were measured, and the morphological, mechanical and thermal properties of the NMPCB/PVC composite material were investigated. The results show that recycled NMPCB powders, when added below a threshold, tended to increase the tensile strength and bending strength of PVC. When 20 wt% NMPCB powders (relative to the substrate PVC) of an average diameter of 0.08 mm were added, the composite tensile strength and bending strength reached 22.6 MPa and 39.83 MPa, respectively, representing 107.2% and 123.1% improvement over pure PVC. The elongation at break of the composite material reached 151.94% of that of pure PVC, while the Vicat softening temperature of the composite material did not increase significantly compared to the pure PVC. The above results suggest that paper-based NMPCB powders, when used at appropriate amounts, can be effective for toughening PVC. Thus, this study suggests a new route for reusing paper-based NMPCB, which may have a significant beneficial environmental impact. Copyright © 2010 Elsevier Ltd. All rights reserved.

[Application of sintered Ti powder to dental prostheses].

PubMed

Hikosaka, Tatsuya; Tanaka, Yoshinobu; Hoshiai, Kazumoto; Kanazawa, Takeshi; Nakamura, Yoshinori; Tsuda, Kenji; Ohasi, Hideya

2005-04-01

Powder metallurgy is a metal processing technology. Porous titanium produced from powder is widely used. The method is applied to titanium, which is not easy to cast as it sinters under melting point. In prosthetic dentistry, powder metallurgy can be applied to high fusing metal that is biocompatible. In this study, we examined the mechanical characteristics of the Ti sheet produced by sintering and discussed its application to dental prosthesis manufacturing. Ti sheets of 1-mm thickness, in which a binder was added to spherical Ti powder, were produced with the Doctor Blade Method. The sintering was carried out between 900-1150 degrees C at 6 temperatures. The sintered compact was evaluated by dimensional change rate, hardness test, bending strength, tensile strength and SEM observation. Another compact was sintered on the refractory cast. Mechanical strength significantly increased with sintering temperature. In addition, excellent mechanical strength was acquired by adding crushed powder and performing the de-binder process. In the sintering on the refractory cast, pre-baking for more than 100 minutes and sintering at over 1050 degrees C was needed for practical application. It thus seems possible to apply sintered titanium to dental prostheses. However, it will be necessary to examine the control of the shrinkage of the sintered compact in the future too.

Investigation of the degradation of different nickel anode types for alkaline fuel cells (AFCs)

NASA Astrophysics Data System (ADS)

Gülzow, E.; Schulze, M.; Steinhilber, G.

Alkaline fuel cells (AFCs) have the opportunity of becoming important for mobile energy systems as, in contrast to other low temperature fuel cells, the alkaline type requires neither noble metal catalysts nor an expensive polymer electrolyte. In AFCs, nickel is used as anode catalyst in gas diffusion electrodes. The metal catalyst was mixed with polytetraflourethylene (PTFE) as organic binder in a knife mile and rolled onto a metal web in a calendar to prepare the electrode. After an activation process with hydrogen evolution at 5 mA/cm 2 for 18 h, the electrodes were stressed at constant loading in a half cell equipment. During the fuel cell operation, the electrochemical performance decreased due to changes of the polymer (PTFE) and of the metal particles in the electrode, which is described in detail in another paper. In this study, three types of electrodes were investigated. The first type of electrode is composed of pure Raney-nickel and PTFE powder, the nickel particles in the second electrode type were selected according to particle size and in the third electrode copper powder was added to the nickel powder not selected by size. The size selected nickel particles show a better electrochemical performance related to the non-selected catalyst, but due to the electrochemically induced disintegration of the nickel particles the electrochemical performance decreases stronger. The copper powder in the third electrode is added to improve the electronic conductivity of the nickel catalyst, but the copper is not stable under the electrochemical conditions in fuel cell operation. With all three anode types long-term experiments have been performed. The electrodes have been characterized after the electrochemical stressing to investigate the degradation processes.

The mechanical and thermal characteristics of phenolic foam reinforced with kaolin powder and glass fiber fabric

NASA Astrophysics Data System (ADS)

Xiao, Wenya; Huang, Zhixiong; Ding, Jie

2017-12-01

In this work, kaolin powder and glass fiber fabric were added to PF in order to improve its thermal stability and mechanical property. Micro-structures of carbonized PF with kaolin powder were inspected by scanning electron microscopy (SEM) to demonstrate the filler’s pinning effect. SEM results illustrated modified PF had well morphology after high-temperature heat treatment. The Fourier transform infrared spectrometer (FTIR) test was carried out and found that kaolin powder only physically dispersed in PF. The compression test and thermal weight loss test were done on two groups of modified PF (Group A: add powder and fabric; Group B: add powder only). Results showed that all modified PF were better than pure PF, while foams with powder and fabric showed better mechanical characteristic and thermal stability compared with foams with powder only.

Characteristics and nutritional value of whole wheat cracker fortified with tuna bone bio-calcium powder.

PubMed

Benjakul, Soottawat; Karnjanapratum, Supatra

2018-09-01

Whole wheat cracker fortified with tuna bone bio-calcium (Bio-Ca) powder was developed as health-promoting food rich in calcium. Fortification with different levels of Bi-Ca, over the range of 0-50% of whole wheat flour (w/w) on quality and sensory properties of crackers, were determined. Color, thickness, weight and textural properties of crackers varied with the different levels of Bio-Ca powder added, but it was found that up to 30% could be added without detrimental effect on sensory properties. Scanning electron microscopic images showed that the developed crackers were less porous and had a denser structure, compared to the control. Based on scanning electron microscopy-energy dispersive X-ray spectroscopic (SEM-EDX), the cracker containing Bio-Ca powder had calcium and phosphorous distribution with higher intensity, compared to the control. The fortified crackers were rich in calcium and phosphorous with higher protein content but lower fat, carbohydrate, cholesterol and energy value, compared to the control. Copyright © 2018 Elsevier Ltd. All rights reserved.

Mesoporous Carbons With Self-Assembled High-Activity Surfaces (PREPRINT)

DTIC Science & Technology

2006-07-07

temperature-programmed desorption, and potentiometric titrations . Journal of Colloid and Interface Science 2001; 240: 252–258. [40] Rotkin SV, Gogotsi Y...selected carbon samples were treated with nitric acid and the total acid site density determined by base titration [32-34 Boehm 1994; Boehm 2002; 32...washed thoroughly using distilled/deionized water, and dried in the oven. For the titration , 50 mg of HNO3-treated carbon powder was added to 20 ml

Structural development and kinetic analysis of PbTiO3 powders processed at low-temperature via new sol-gel approach

NASA Astrophysics Data System (ADS)

Bel-Hadj-Tahar, Radhouane; Abboud, Mohamed

2018-04-01

The synthesis of crystalline lead titanate powder by a generic low-temperature sol-gel approach is developed. Acetoin was added as ligand, instead of the commonly used alkanolamines, to ensure total dissolution of the precursor compounds. The feasibility of the acetoin-Ti isopropoxide complex as a new precursor of PbTiO3 perovskite particles via sol-gel method has been demonstrated. No excess lead has been introduced. Nanometric PbTiO3 crystallites have been formed at 400 °C under atmospheric pressure from titanium isopropoxide and lead acetate in alcoholic solution by remarkably low activation energy of crystallization process of 90 kJ mol-1. The powders show tetragonal lattice and dendritic morphology. In addition to the effect of heat-treatment temperature, time, and atmosphere, the sol chemistry particularly influenced the phase composition, particle size, and particle morphology. The use of different ligands significantly modified powder morphology. The extent of the crystallization was quantitatively evaluated by differential thermal analysis and analyzed by Johnson-Mehl-Avrami approach. The crystallization followed two rate regimes depending on the interval of the crystallized fraction.

Utilization of whey powder as substrate for low-cost preparation of β-galactosidase as main product, and ethanol as by-product, by a litre-scale integrated process.

PubMed

You, Shengping; Chang, Hongxing; Yin, Qingdian; Qi, Wei; Wang, Mengfan; Su, Rongxin; He, Zhimin

2017-12-01

Whey powder, a by-product of dairy industry, is an attractive raw material for value-added products. In this study, utilization of whey powder as substrate for low-cost preparation of β-galactosidase as main product and ethanol as by-product were investigated by a litre-scale integrated strategy, encompassing fermentation, isolation, permeabilization and spray drying. Firstly, through development of low-cost industrial culture and fed-batch strategies by Kluyveromyces lactis, 119.30U/mL β-galactosidase activity and 16.96mg/mL by-product ethanol were achieved. Afterward, an up-dated mathematic model for the recycling permeabilization was established successfully and 30.4g cells sediment isolated from 5L fermentation broth were permeabilized completely by distilled ethanol from broth supernatant. Then β-galactosidase product with 5.15U/mg from protection of gum acacia by spray drying was obtained. Furthermore, by-product ethanol with 31.08% (v/v) was achieved after permeabilization. Therefore, the integrated strategy using whey powder as substrate is a feasible candidate for industrial-scale implementation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Particle Morphology Effects on Flow Characteristics of PS304 Plasma Spray Coating Feedstock Powder Blend

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.; DellaCorte, Christopher; Eylon, Daniel

2002-01-01

The effects of BaF2-CaF 2 particle morphology on PS304 feedstock powder flow ability have been investigated. BaF2-CaF2 eutectic powders were fabricated by comminution (angular) and by gas atomization (spherical). The fluoride powders were added incrementally to the other powder constituents of the PS304 feedstock: nichrome, chromia, and silver powders. A linear relationship between flow time and concentration of BaF2-CaF2 powder was found. Flow of the powder blend with spherical BaF2-CaF2 was better than the angular BaF2-CaF2. Flow ability of the powder blend with angular fluorides decreased linearly with increasing fluoride concentration. Flow of the powder blend with spherical fluorides was independent of fluoride concentration. Results suggest that for this material blend, particle morphology plays a significant role in powder blend flow behavior, offering potential methods to improve powder flow ability and enhance the commercial potential. These findings may have applicability to other difficult-to-flow powders such as cohesive ceramics.

Structural markers of the evolution of whey protein isolate powder during aging and effects on foaming properties.

PubMed

Norwood, E-A; Le Floch-Fouéré, C; Briard-Bion, V; Schuck, P; Croguennec, T; Jeantet, R

2016-07-01

The market for dairy powders, including high added-value products (e.g., infant formulas, protein isolates) has increased continuously over the past decade. However, the processing and storage of whey protein isolate (WPI) powders can result in changes in their structural and functional properties. It is therefore of great importance to understand the mechanisms and to identify the structural markers involved in the aging of WPI powders to control their end use properties. This study was performed to determine the effects of different storage conditions on protein lactosylations, protein denaturation in WPI, and in parallel on their foaming and interfacial properties. Six storage conditions involving different temperatures (θ) and water activities (aw) were studied for periods of up to 12mo. The results showed that for θ≤20°C, foaming properties of powders did not significantly differ from nonaged whey protein isolates (reference), regardless of the aw. On the other hand, powders presented significant levels of denaturation/aggregation and protein modification involving first protein lactosylation and then degradation of Maillard reaction products, resulting in a higher browning index compared with the reference, starting from the early stage of storage at 60°C. These changes resulted in a higher foam density and a slightly better foam stability (whisking) at 6mo. At 40°C, powders showed transitional evolution. The findings of this study will make it possible to define maximum storage durations and to recommend optimal storage conditions in accordance with WPI powder end-use properties. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Synthesis and characterization of titanium dioxide (TiO2) nanopowder

NASA Astrophysics Data System (ADS)

Munirah, S.; Nadzirah, Sh.; Khusaimi, Z.; Fazlena, H.; Rusop, M.

2018-05-01

Titanium dioxide (TiO2) powder was synthesized via sol-gel technique using Titanium tetraisopropoxide (TTIP) and ethanol as precursors. Acetylacetone, distilled water, polyethylene glycol (PEG) and stabilizers (glacial acetic acid and nitric acid) were then added to the solution. The solution was left for ageing for 24 hours and then dried into powder. The synthesized powders were characterized by X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Thermogravimetric Analysis (TGA).

Determination of whey adulteration in milk powder by using laser induced breakdown spectroscopy.

PubMed

Bilge, Gonca; Sezer, Banu; Eseller, Kemal Efe; Berberoglu, Halil; Topcu, Ali; Boyaci, Ismail Hakki

2016-12-01

A rapid and in situ method has been developed to detect and quantify adulterated milk powder through adding whey powder by using laser induced breakdown spectroscopy (LIBS). The methodology is based on elemental composition differences between milk and whey products. Milk powder, sweet and acid whey powders were produced as standard samples, and milk powder was adulterated with whey powders. Based on LIBS spectra of standard samples and commercial products, species was identified using principle component analysis (PCA) method, and discrimination rate of milk and whey powders was found as 80.5%. Calibration curves were obtained with partial least squares regression (PLS). Correlation coefficient (R(2)) and limit of detection (LOD) values were 0.981 and 1.55% for adulteration with sweet whey powder, and 0.985 and 0.55% for adulteration with acid whey powder, respectively. The results were found to be consistent with the data from inductively coupled plasma - mass spectrometer (ICP-MS) method. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of Freeze-Dried Powders of Genetically Engineered Microbial Strains as Adsorbents for Rare Earth Metal Ions.

PubMed

Moriwaki, Hiroshi; Masuda, Reiko; Yamazaki, Yuki; Horiuchi, Kaoru; Miyashita, Mari; Kasahara, Jun; Tanaka, Tatsuhito; Yamamoto, Hiroki

2016-10-12

The adsorption behaviors of the rare earth metal ions onto freeze-dried powders of genetically engineered microbial strains were compared. Cell powders obtained from four kinds of strains, Bacillus subtilis 168 wild type (WT), lipoteichoic acid-defective (ΔLTA), wall teichoic acid-defective (ΔWTA), and cell wall hydrolases-defective (EFKYOJLp) strains, were used as an adsorbent of the rare earth metal ions at pH 3. The adsorption ability of the rare earth metal ions was in the order of EFKYOJLp > WT > ΔLTA > ΔWTA. The order was the same as the order of the phosphorus quantity of the strains. This result indicates that the main adsorption sites for the ions are the phosphate groups and the teichoic acids, LTA and WTA, that contribute to the adsorption of the rare earth metal ions onto the cell walls. The contribution of WTA was clearly greater than that of LTA. Each microbial powder was added to a solution containing 16 kinds of rare earth metal ions, and the removals (%) of each rare earth metal ion were obtained. The scandium ion showed the highest removal (%), while that of the lanthanum ion was the lowest for all the microbial powders. Differences in the distribution coefficients between the kinds of lanthanide ions by the EFKYOJLp and ΔWTA powders were greater than those of the other strains. Therefore, the EFKYOJLp and ΔWTA powders could be applicable for the selective extraction of the lanthanide ions. The ΔLTA powder coagulated by mixing with a rare earth metal ion, although no sedimentation of the WT or ΔWTA powder with a rare earth metal ion was observed under the same conditions. The EFKYOJLp powder was also coagulated, but its flocculating activity was lower than that of ΔLTA. The ΔLTA and EFKYOJLp powders have a long shape compared to those of the WT or ΔWTA strain. The shapes of the cells will play an important role in the sedimentation of the microbial powders with rare earth metal ions. As the results, three kinds of the genetically engineered microbial powders revealed unique adsorption behaviors of the rare earth metal ions.

Physical and Sensory Properties of Ice Cream Containing Fermented Pepper Powder.

PubMed

Yeon, Su-Jung; Kim, Ji-Han; Hong, Go-Eun; Park, Woojoon; Kim, Soo-Ki; Seo, Han-Geuk; Lee, Chi-Ho

2017-01-01

This study was conducted to investigate the physical and sensory properties of ice cream containing fermented pepper powder. Three ice cream formulas were manufactured: 1, control; 2, supplemented with 0.1% fermented pepper powder; and 3, supplemented with 0.2% fermented pepper powder. Formulas 2 and 3 had significantly higher viscosity and lower overrun than formula 1 ( p <0.05). Additionally, ice creams supplemented with fermented pepper powder were harder and maintained their forms longer than the controls. 0.2% fermented pepper powder added ice cream had no pungency as much as that of control and overall sensory attribute was not significantly different from control. Therefore, ice cream containing fermented pepper powder maintained physical and sensory properties similar to the controls, and maintenance was better. It means fermented pepper powder ice cream can be utilized as the material of functional food (dessert).

Physical and Sensory Properties of Ice Cream Containing Fermented Pepper Powder

PubMed Central

Kim, Soo-Ki; Seo, Han-Geuk

2017-01-01

This study was conducted to investigate the physical and sensory properties of ice cream containing fermented pepper powder. Three ice cream formulas were manufactured: 1, control; 2, supplemented with 0.1% fermented pepper powder; and 3, supplemented with 0.2% fermented pepper powder. Formulas 2 and 3 had significantly higher viscosity and lower overrun than formula 1 (p<0.05). Additionally, ice creams supplemented with fermented pepper powder were harder and maintained their forms longer than the controls. 0.2% fermented pepper powder added ice cream had no pungency as much as that of control and overall sensory attribute was not significantly different from control. Therefore, ice cream containing fermented pepper powder maintained physical and sensory properties similar to the controls, and maintenance was better. It means fermented pepper powder ice cream can be utilized as the material of functional food (dessert). PMID:28316469

Effect of the oxygen content in a salt solution on the characteristics of sodium-reduced tantalum powders

NASA Astrophysics Data System (ADS)

Kolosov, V. N.; Orlov, V. M.; Miroshnichenko, M. N.; Prokhorova, T. Yu.; Masloboeva, S. M.; Belyaevskii, A. T.

2009-02-01

The characteristics of the tantalum powders produced by sodium thermal reduction from salt melts based on K2TaF7 and NaCl with various amounts of added oxycompounds K3TaOF6 and K2Ta2O3F6 are studied. At a molar ratio of oxygen to tantalum of 1.25 in the initial melt, capacitor tantalum powders with a specific surface area more than 3 m2/g are produced. The specific capacitance of the anodes made from these powders reaches 58 mC/g.

The influence of metal Mg on micro-morphology and crystallinity of spherical hexagonal boron nitride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Ning, E-mail: zhangning5832@163.com; Liu, Huan; Kan, Hongmin

2015-08-15

Highlights: • The action mechanism of Mg to the synthesis of spherical BN was explored. • The influence of Mg content on the crystallinity of h-BN powders was studied. • Even if not added any template, the spherical h-BN could be prepared. - Abstract: This search used the boric acid and borax as a source of boron, urea as a nitrogen source, Mg as metal catalyst, and thus prepared different micro-morphology and crystallinity hexagonal boron nitride powders under a flowing ammonia atmosphere at a nitriding temperature of 750 °C. The effect of Mg content on the crystallinity and micro-morphology ofmore » hexagonal boron nitride powders was studied, and the Mg action mechanism was explored. Without the added surfactant, the graphitization index (GI) was 6.87, and the diameter of the spherical h-BN was bigger. When the added Mg were 0.1 g, 0.3 g, 0.5 g and 0.7 g, the (GI) decreased to 6.04, 5.67, 4.62 and 4.84, respectively. When the Mg content was higher (0.9 g), GI value increased rapidly, and the crystallinity became bad. When the Mg content was 0.5 g, the dispersion of h-BN powders was at its optimum and refinement apparently, and the crystallinity at its highest.« less

[Study on nano-CaCO3 applicated in Xin Yue Shu Capsules preliminarily].

PubMed

Jiang, Yan-Rong; Zhang, Zhen-Hai; Cui, Li; He, Jun-Jie; Hu, Shao-Ying; Jia, Xiao-Bin

2012-11-01

To investigate the characteristics of nano-CaCO3 applicated in Xin Yue Shu Capsules. Studied the effect of different dosages of aerosil or nano-CaCO3 on fluidity, bulk density, moisture absorption of Xin Yue Shu capsules spray drying powder. In vitro dissolution and ferulic acid stability of Xin Yue Shu capsules was observed. It significantly improved powder fluidity and bulk density of Xin Yue Shu spray drying powder when aerosil or nano-CaCO3 was added. But there was no significant effect on powder moisture absorption, ferulic acid in vitro dissolution and ferulic acid stability. The effect of Nano-CaCO3 on improving powder fluidity and bulk density applicated in the spray drying powder of traditional Chinese medicine deserves studying further.

Flavor Enhancer From Catfish (Clarias batrachus) Bekasam Powder and Angiotensin-I-Converting Enzyme (ACE) Inhibitory Activity in Various Dishes

NASA Astrophysics Data System (ADS)

Lestari, Yanesti N.; Murwani, Retno; Agustini, Tri W.

2018-02-01

Flavor enhancer is characterized by high glutamic acid content and it can be obtained from fermented food such as Bekasam. Fermented food had inhibitory effect on Angiotensin-I-Converting Enzyme (ACE) activity which is advantageous for hypertension. However, such activity was not known to sustain in food system. The aim of this research was to study addition of flavour enhancer from Catfish Bekasam Powder (CBP) in various food systems and to determine the ACE inhibitory (ACEI) activity in the food system. Four food system consisted of carrot, champignon, and chicken meat dishes were boiled in water and added with CBP or MSG. Each food system was added with graded level of CBP (0%; 0.5%; 0.8%; 1.1%; and 1,4%) and for control monosodium glutamate (MSG) was used. ACEI activity in each food system and organoleptic test using multiple comparison differentiation on 15 semi-trained panellists were determined. The results showed that there were fluctuation of ACEI activity in the carrot, champignon, and chicken meat dishes (p=0.017; 0.043; and 0.032). The MSG containing dishes showed the lowest ACEI activity. Addition of graded level of CBP on carrot, champignon, and chicken meat dishes were directly proportional to glutamic acid content but inversely proportional to ACEI activity (p<0.05). The addition of commercial MSG on all dishes increased glutamic acid content but reduced ACE-inhibitory activity significantly (p<0.05). Comparing CBP to MSG addition in champignon dish revealed that increasing level of CBP increased the flavour preference of the panellists. On the contrary the higher the addition CBP in noodle and chicken meat dishes the worse were the flavour score (p<0.05). It can be concluded that the addition of CBP as flavour enhancer on various dishes can deliver better flavour and ACE-inhibitory activity than the addition of commercial MSG.

Removal of polycyclic aromatic hydrocarbons from soil using a composite material containing iron and activated carbon in the freeze-dried calcium alginate matrix: Novel soil cleanup technique.

PubMed

Funada, Mako; Nakano, Takeshi; Moriwaki, Hiroshi

2018-06-05

A novel clean-up technology to remove polycyclic aromatic hydrocarbons (PAHs) from solid samples by magnetic separation using a composite containing iron powder as a magnetic material and activated carbon as an adsorbent in the freeze-dried calcium alginate matrix (Fe-AC-alg) has been developed. The Fe-AC-alg powder (50 mg), mixed with 1.0 g of glass beads having 12 kinds of adsorbed PAHs, was shaken without adding solvents at 300 rpm. After shaking, the Fe-AC-alg powder was separated using a permanent magnet. The quantity of the PAHs extracted from the glass beads treated by this method was determined. The removal (%) of the PAHs was over 96%. A roadside soil sample (10 g) was mixed with the Fe-AC-alg (1.0 g) for 2 weeks. The removal (%) of benzo[a]pyrene from the sample by the presented technique was 78%. The toxic equivalent concentration (Σ BaP eq ) for the sample decreased from 0.27 to 0.10 mg kg -1 by this method. The presented method is very simple, economical, and environment-friendly. Copyright © 2018 Elsevier B.V. All rights reserved.

Method of concurrently filtering particles and collecting gases

DOEpatents

Mitchell, Mark A; Meike, Annemarie; Anderson, Brian L

2015-04-28

A system for concurrently filtering particles and collecting gases. Materials are be added (e.g., via coating the ceramic substrate, use of loose powder(s), or other means) to a HEPA filter (ceramic, metal, or otherwise) to collect gases (e.g., radioactive gases such as iodine). The gases could be radioactive, hazardous, or valuable gases.

Development of Nanoporous Carbide-Derived Carbon Electrodes for High-Performance Lithium-Ion Batteries

DTIC Science & Technology

2011-09-01

carbon produced from TiC (From [10]). .................................... 27 Figure 9. LiFePO4 , acetylene black, and PVDF powders in weighing boat...dispenser, and the ball milled powder mixture x containing LiFePO4 , acetylene black, and PVDF binder; and b) Prepared slurry after adding NMP solvent to...the powder mixture. ..... 39 Figure 12. Sample vial containing a LiFePO4 slurry inside the ultrasonic bath. Each vial was sonicated for 30 minutes

Degradation assessment of natural weathering on low density polyethylene/thermoplastic soya spent powder blends

NASA Astrophysics Data System (ADS)

Nuradibah, M. A.; Sam, S. T.; Noriman, N. Z.; Ragunathan, S.; Ismail, H.

2015-07-01

Soya spent powder was blended with low density polyethylene (LDPE) ranging from 5-25 wt%. Glycerol was added to soya spent powder (SSP) for preparation of thermoplastic soya spent powder (TSSP). Then, the blends were exposed to natural weathering for 6 months. The susceptibility of the LDPE/soya spent powder blends based on its tensile, morphological properties and structural changes was measured every three months. The tensile strength of LDPE/TSSP blends after 6 months of weathering was the lowest compared to the other blends whereas LDPE/SSP blends after 6 months of weathering demonstrated the lowest elongation at break (Eb). Large pore can be seen on the surface of 25 wt% of LDPE/SSP blends.

Recycled tetrahedron-like CuCl from waste Cu scraps for lithium ion battery anode.

PubMed

Hou, Hongying; Yao, Yuan; Liu, Song; Duan, Jixiang; Liao, Qishu; Yu, Chengyi; Li, Dongdong; Dai, Zhipeng

2017-07-01

The wide applications of metal Cu inevitably resulted in a large quantity of waste Cu materials. In order to recover the useful Cu under the mild conditions and reduce the environmental emission, waste Cu scraps were recycled in the form of CuCl powders with high economic value added (EVA) via the facile hydrothermal route. The recycled CuCl powders were characterized in terms of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). The results suggested that the recycled CuCl powders consisted of many regular tetrahedron-like micro-particles. Furthermore, in order to reduce the cost of lithium ion battery (LIB) anode and build the connection of waste Cu scraps and LIB, the recycled CuCl powders were evaluated as the anode active material of LIB. As expected, the reversible discharge capacity was about 171.8mAh/g at 2.0C even after 50 cycles, implying the satisfactory cycle stability. Clearly, the satisfactory results may open a new avenue to develop the circular economy and the sustainable energy industry, which would be very important in terms of both the resource recovery and the environmental protection. Copyright © 2017. Published by Elsevier Ltd.

Formulation and physicochemical and sensorial evaluation of biscuit-type cookies supplemented with fruit powders.

PubMed

Uchoa, Ana Maria Athayde; Correia da Costa, José Maria; Maia, Geraldo Arraes; Meira, Tatyane Ribeiro; Sousa, Paulo Henrrique Machado; Montenegro Brasil, Isabella

2009-06-01

Cashew apple and guava residues from fruit juice industry were prepared as dehydrated fruit powders and used at different levels of wheat flour substitution for cookies formulations. The effects of guava and cashew apple fruit powders supplementation on physicochemical and sensorial characteristics of the cookies were evaluated. The pH, fibre and protein content were significantly affected. Biscuits with 15 g and 20 g/100g cashew apple and guava fruit powders showed the highest scores for sensorial attributes, respectively. The supplementation seems to be suited for wheat flour substitution and it is possible to obtain cookies with value-added food ingredient within the standards.

Energy-beam-driven rapid fabrication system

DOEpatents

Keicher, David M.; Atwood, Clinton L.; Greene, Donald L.; Griffith, Michelle L.; Harwell, Lane D.; Jeantette, Francisco P.; Romero, Joseph A.; Schanwald, Lee P.; Schmale, David T.

2002-01-01

An energy beam driven rapid fabrication system, in which an energy beam strikes a growth surface to form a molten puddle thereon. Feed powder is then injected into the molten puddle from a converging flow of feed powder. A portion of the feed powder becomes incorporated into the molten puddle, forcing some of the puddle contents to freeze on the growth surface, thereby adding an additional layer of material. By scanning the energy beam and the converging flow of feed powder across the growth surface, complex three-dimensional shapes can be formed, ready or nearly ready for use. Nearly any class of material can be fabricated using this system.

Simultaneous removal of ammonia and N-nitrosamine precursors from high ammonia water by zeolite and powdered activated carbon.

PubMed

Xue, Runmiao; Donovan, Ariel; Zhang, Haiting; Ma, Yinfa; Adams, Craig; Yang, John; Hua, Bin; Inniss, Enos; Eichholz, Todd; Shi, Honglan

2018-02-01

When adding sufficient chlorine to achieve breakpoint chlorination to source water containing high concentration of ammonia during drinking water treatment, high concentrations of disinfection by-products (DBPs) may form. If N-nitrosamine precursors are present, highly toxic N-nitrosamines, primarily N-nitrosodimethylamine (NDMA), may also form. Removing their precursors before disinfection should be a more effective way to minimize these DBPs formation. In this study, zeolites and activated carbon were examined for ammonia and N-nitrosamine precursor removal when incorporated into drinking water treatment processes. The test results indicate that Mordenite zeolite can remove ammonia and five of seven N-nitrosamine precursors efficiently by single step adsorption test. The practical applicability was evaluated by simulation of typical drinking water treatment processes using six-gang stirring system. The Mordenite zeolite was applied at the steps of lime softening, alum coagulation, and alum coagulation with powdered activated carbon (PAC) sorption. While the lime softening process resulted in poor zeolite performance, alum coagulation did not impact ammonia and N-nitrosamine precursor removal. During alum coagulation, more than 67% ammonia and 70%-100% N-nitrosamine precursors were removed by Mordenite zeolite (except 3-(dimethylaminomethyl)indole (DMAI) and 4-dimethylaminoantipyrine (DMAP)). PAC effectively removed DMAI and DMAP when added during alum coagulation. A combination of the zeolite and PAC selected efficiently removed ammonia and all tested seven N-nitrosamine precursors (dimethylamine (DMA), ethylmethylamine (EMA), diethylamine (DEA), dipropylamine (DPA), trimethylamine (TMA), DMAP, and DMAI) during the alum coagulation process. Copyright © 2017. Published by Elsevier B.V.

76 FR 61531 - Endangered and Threatened Wildlife and Plants; 90-Day Finding on a Petition To List 10 Subspecies...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-04

... that listing the following 4 of the 10 subspecies as threatened or endangered may be warranted: Baking...: Baking Powder Flat blue butterfly (Euphilotes bernardino minuta), Mono Basin skipper (Hesperia uncas.... The Baking Powder Flat blue butterfly was added as Euphilotes battoides ssp., now known as Euphilotes...

Presence of electrostatically adsorbed polysaccharides improves spray drying of liposomes.

PubMed

Karadag, Ayse; Özçelik, Beraat; Sramek, Martin; Gibis, Monika; Kohlus, Reinhard; Weiss, Jochen

2013-02-01

Spray drying of liposomes with conventional wall materials such as maltodextrins often yields nonfunctional powders, that is, liposomes break down during drying and rehydration. Electrostatically coating the surface of liposomes with a charged polymer prior to spray drying may help solve this problem. Anionic lecithin liposomes (approximately 400 nm) were coated with lower (approximately 500 kDa, LMW-C) or higher (approximately 900 kDa, HMW-C) molecular weight cationic chitosan using the layer-by-layer depositing method. Low (DE20, LMW-MD) or high molecular weight (DE2, HMW-MD) maltodextrin was added as wall material to facilitate spray drying. If surfaces of liposomes (1%) were completely covered with chitosan (0.4%), no bridging or depletion flocculation would occur, and mean particle diameters would be approximately 500 nm. If maltodextrins (20%) were added to uncoated liposomes, extensive liposomal breakdown would occur making the system unsuitable for spray drying. No such aggregation or breakdown was observed when maltodextrin was added to chitosan-coated liposomes. Size changed little or even decreased slightly depending on the molecular weight of maltodextrin added. Scanning electron microscopy images of powders containing chitosan-coated liposomes revealed that their morphologies depended on the type of maltodextrin added. Powders prepared with LMW-MD contained mostly spherical particles while HMW-MD powders contained particles with concavities and dents. Upon redispersion, coated liposomes yielded back dispersions with particle size distributions similar to the original ones, except for LMW-C coated samples that had been spray dried with HMW-MD which yielded aggregates (approximately 30 μm). Results show that coating of liposomes with an absorbing polymer allows them to be spray dried with conventional maltodextrin wall materials. Liposomes have attracted considerable attention in the food and agricultural, biomedical industries for the delivery of functional components. However, maintaining their stability in aqueous dispersion represents a challenge for their commercialization. Spray drying may promise a solution to that problem. However, prior to this study spray drying of liposomes often led to the loss of structural integrity. Results of this study suggest that spray drying might be used to produce commercially feasible liposomal powders if proper combinations of adsorbing and nonadsorbing polymers are used in the liquid precursor system. © 2013 Institute of Food Technologists®

Effect of incorporation of pumpkin (Cucurbita moshchata) powder and guar gum on the rheological properties of wheat flour.

PubMed

Kundu, Himani; Grewal, Raj Bala; Goyal, Ankit; Upadhyay, Neelam; Prakash, Saurabh

2014-10-01

The present study was carried out to study the effect of incorporation of fibre rich pumpkin powder and guar gum on the farinographic characteristics of wheat flour. The flour and pumpkin powder were assessed for proximate composition, total dietary fibre, minerals and β-carotene. Pumpkin powder contained appreciable amount of fibre, minerals and β-carotene. The effects of incorporation of different levels of pumpkin powder and guar gum along with pumpkin powder on farinographic characteristics were studied. Dough development time, dough stability, time to break down and farinograph quality number increased whereas mixing tolerance index decreased with incorporation of pumpkin powder (> 5 %) and guar gum (1.0 and 1.5 %) along with pumpkin powder in the flour. Resistance to extension as well as extensibility of dough prepared increased significantly by adding pumpkin powder (5-15 %) whereas increase in resistance to extension only was noticed with inclusion of guar gum (0.5-1.5 %) to flour containing 5 % pumpkin powder. Results indicated that pumpkin can be processed to powder that can be utilized with guar gum for value addition.

Influence of combinations of fenugreek, garlic, and black pepper powder on production traits of the broilers.

PubMed

Kirubakaran, A; Moorthy, M; Chitra, R; Prabakar, G

2016-05-01

To study the effects of combinations of fenugreek (Trigonella foenum-graecum L.), garlic (Allium sativum), and black pepper (Piper nigrum) powder supplementation on production traits of broiler chickens. A total of 288 commercial broiler chicks were randomly assigned to 1-9 groups with 4 replicates each. An experiment was conducted in broilers with different feed formulations; control feed, with no added fenugreek, garlic, and black pepper powder; and 8 treatment groups receiving feed supplemented with different combinations of fenugreek, garlic, and black pepper powder. The individual broilers' body weight and feed consumption were recorded and calculate the body weight gain and feed conversion ratio (FCR). Broiler's weight gain and FCR were significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). Cumulative feed consumption was significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). The combination of garlic and black pepper powder supplemented broiler feed fed groups showed higher production performance. The 5 g/kg garlic powder+1 g/kg black pepper powder and 10 g/kg garlic powder+2 g/kg black pepper powder significantly improved the weight gain and FCR.

Experimental Study of Structure/Behavior Relationship for a Metallized Explosive

NASA Astrophysics Data System (ADS)

Bukovsky, Eric; Reeves, Robert; Gash, Alexander; Glumac, Nick

2017-06-01

Metal powders are commonly added to explosive formulations to modify the blast behavior. Although detonation velocity is typically reduced compared to the neat explosive, the metal provides other benefits. Aluminum is a common additive to increase the overall energy output and high-density metals can be useful for enhancing momentum transfer to a target. Typically, metal powder is homogeneously distributed throughout the material; in this study, controlled distributions of metal powder in explosive formulations were investigated. The powder structures were printed using powder bed printing and the porous structures were filled with explosives to create bulk explosive composites. In all cases, the overall ratio between metal and explosive was maintained, but the powder distribution was varied. Samples utilizing uniform distributions to represent typical materials, discrete pockets of metal powder, and controlled, graded powder distributions were created. Detonation experiments were performed to evaluate the influence of metal powder design on the output pressure/time and the overall impulse. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Study of the activity of the local adding [ash from palm plantation wastes

NASA Astrophysics Data System (ADS)

Rezig, D.; Bentabba, M. T.

2018-05-01

The objectify of this work is to study the activity of the ash by substitution of 25℅ cement of mineral powder ash from palm plantation wastes, and its influences mechanical performances on mortar. Such as the resistance of the compression, the traction, and durability by reducing calcium hydroxide content Ca[OH]2 generated by chemical reaction of cement, which has a harmful effect in durability. The activity of this waste was evaluated in the utilized of mechanic attempts resistance of the compression and flexion in 28 day] was also studied, the obtained results shows the best result of the index of ash activity is i=0,69 was obtained in mixing cement with CRS.

Aqueous Combustion Synthesis and Characterization of Nanosized Tetragonal Zirconia Single Crystals

NASA Astrophysics Data System (ADS)

Reddy, B. S. B.; Mal, Indrajit; Tewari, Shanideep; Das, Karabi; Das, Siddhartha

2007-08-01

Nanocrystalline zirconia powder has been synthesized by an aqueous combustion synthesis route using glycine as fuel and nitrate as oxidizer. The powders have been prepared by using different glycine to zirconyl nitrate molar ratios (G/N). The powders produced with different G/N ratios have been characterized by X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) to determine the parameters resulting from powder with attractive properties. The theoretical combustion temperature (T ad ) has been calculated for different G/N ratios, and it is correlated with powder characteristics. An attempt is also made to explain the stability of tetragonal zirconia on the basis of extrinsic factors such as the morphology of nanocrystallites. Nanocrystalline metastable tetragonal zirconia (˜25 nm) powder (TZ) with disc-shaped morphology has been produced with a weak agglomeration in fuel deficient mixtures.

[3H]Indole-3-acetyl-myo-inositol hydrolysis by extracts of Zea mays L. vegetative tissue

NASA Technical Reports Server (NTRS)

Hall, P. J.; Bandurski, R. S.

1986-01-01

[3H]Indole-3-acetyl-myo-inositol was hydrolyzed by buffered extracts of acetone powders prepared from 4 day shoots of dark grown Zea mays L. seedlings. The hydrolytic activity was proportional to the amount of extract added and was linear for up to 6 hours at 37 degrees C. Boiled or alcohol denatured extracts were inactive. Analysis of reaction mixtures by high performance liquid chromatography demonstrated that not all isomers of indole-3-acetyl-myo-inositol were hydrolyzed at the same rate. Buffered extracts of acetone powders were prepared from coleoptiles and mesocotyls. The rates of hydrolysis observed with coleoptile extracts were greater than those observed with mesocotyl extracts. Active extracts also catalyzed the hydrolysis of esterase substrates such as alpha-naphthyl acetate and the methyl esters of indoleacetic acid and naphthyleneacetic acid. Attempts to purify the indole-3-acetyl-myo-inositol hydrolyzing activity by chromatographic procedures resulted in only slight purification with large losses of activity. Chromatography over hydroxylapatite allowed separation of two enzymically active fractions, one of which catalyzed the hydrolysis of both indole-3-acetyl-myo-inositol and esterase substrates. With the other enzymic hydrolysis of esterase substrates was readily demonstrated, but no hydrolysis of indole-3-acetyl-myo-inositol was ever detected.

DARPA Advanced Cannon Propellant (ACP) Library User’s Guide. Appendix F. Patents Dealing with Fluid Propellant Technology

DTIC Science & Technology

1981-06-15

tallisation temperature were added 0.4 parts of hydrox- mannitol, and 15.0 parts coarse aluminium powder were ypropylated guar gum which was allowed to...3.0 parts of8 15 coarse aluminium powder , 0.5 parts of hydroxy- propylated guar gum , 0.2 parts of zinc chromate and A slurry was prepared by the mixing...4 molecules of ethylene oxide), 10 parts of foaming agent and entrapped air bubbles into the comn- coarse aluminium powder , 0.7 parts of guar gum

Discussion on the application of high additional value of high purity and high quality direct reduced iron

NASA Astrophysics Data System (ADS)

Yue, Chongfeng; Bai, Lu; Hong, Yicheng; Xu, Lijun

2018-03-01

The high purity and high quality direct reduced iron(DRI) products which were produced by high grade and high quality iron powder, with a high grade and low impurity characteristics. This article introduced the application of high purity and high quality DRI in the fields of amorphous base material, atomized iron powder, powder superalloy, high purity and ultra-low carbon special metallurgy products, precision casting, super alloy and various iron-based alloys. It provides a reference for the high added value utilization of DRI.

Reduction of postprandial blood glucose in healthy subjects by buns and flatbreads incorporated with fenugreek seed powder.

PubMed

Robert, Sathyasurya Daniel; Ismail, Aziz Al-Safi; Rosli, Wan Ishak Wan

2016-10-01

This study aimed to determine whether fenugreek seed powder could reduce the glycemic response and glycemic index (GI) when added to buns and flatbreads. In a randomised, controlled crossover trial, ten healthy human subjects (five men, five women) were given 50 g glucose (reference food, twice); buns (0 and 10 % fenugreek seed powder); and flatbreads (0 and 10 % fenugreek seed powder) on six different occasions. Finger prick capillary blood samples were collected at 0, 15, 30, 45, 60, 90 and 120 min after the start of the meal. The palatability of the test meals was scored using Likert scales. The incremental areas under the glucose curve value of buns and flatbreads with 10 % fenugreek (138 ± 17 mmol × min/L; 121 ± 16 mmol × min/L) were significantly lower than those of 0 % fenugreek bun and flatbreads (227 ± 15 mmol × min/L; 174 ± 14 mmol × min/L, P = <0.01). Adding 10 % fenugreek seed powder reduced the GI of buns from 82 ± 5 to 51 ± 7 (P < 0.01) and to the GI of flatbread from 63 ± 4 to 43 ± 5 (P < 0.01). These results suggest that replacing 10 % of refined wheat flour with fenugreek seed powder significantly reduces the glycemic response and the GI of buns and flatbreads. Thus, fenugreek powder may be a useful functional ingredient to reduce postprandial glycemia.

2011 Final Report - Nano-Oxide Photocatalysis for Solar Energy Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eckstein, James N.; Suslick, Kenneth S.

2011-10-19

We have very recently discovered a new hydrogen-producing photocatalyst is BiNbO4. BiNbO4 powders prepared by solid state reaction were tested for photocatalytic activity in methanol solutions under UV irradiation. When the material is tested without the presence of a Pt co-catalyst, photocatalytic activity for H2 evolution is superior to that of TiO2. It was also found that BiNbO4 photodegrades into metallic Bi and reduced Nb oxides after use; materials were characterized by SEM, XRD, and XPS. Adding Pt to the surface of the photocatalyst increases photocatalytic activity and importantly, helps to prevent photodegradation of the oxide material. With 1 wt.more » % Pt loading, photodegradation is essentially absent. BiNbO4 photodegrades into metallic Bi and reduced Nb oxides after use; materials were characterized by SEM, XRD, and XPS. Adding Pt to the surface of the photocatalyst increases photocatalytic activity and importantly, helps to prevent photodegradation of the oxide material. With 1 wt. % Pt loading, photodegradation is essentially absent.« less

Preparation of powders suitable for conversion to useful .beta.-aluminas

DOEpatents

Morgan, Peter E. D.

1982-01-01

A process for forming a precursor powder which, when suitably pressed and sintered forms highly pure, densified .beta.- or .beta."-alumina, comprising the steps of: (1) forming a suspension (or slurry) of Bayer-derived Al(OH).sub.3 in a water-miscible solvent; (2) adding an aqueous solution of a Mg compound, a Li compound, a Na compound or mixtures thereof to the Bayer-derived Al(OH).sub.3 suspension while agitating the mixture formed thereby, to produce a gel; (3) drying the gel at a temperature above the normal boiling point of water to produce a powder material; (4) lightly ball milling and sieving said powder material; and (5) heating the ball-milled and sieved powder material at a temperature of between 350.degree. to 900.degree. C. to form the .beta.- or .beta."-alumina precursor powder. The precursor powder, thus formed, may be subsequently isopressed at a high pressure and sintered at an elevated temperature to produce .beta.- or .beta."-alumina. BACKGROUND OF THE INVENTION

A Review of Disintegration Mechanisms and Measurement Techniques.

PubMed

Markl, Daniel; Zeitler, J Axel

2017-05-01

Pharmaceutical solid dosage forms (tablets or capsules) are the predominant form to administer active pharmaceutical ingredients (APIs) to the patient. Tablets are typically powder compacts consisting of several different excipients in addition to the API. Excipients are added to a formulation in order to achieve the desired fill weight of a dosage form, to improve the processability or to affect the drug release behaviour in the body. These complex porous systems undergo different mechanisms when they come in contact with physiological fluids. The performance of a drug is primarily influenced by the disintegration and dissolution behaviour of the powder compact. The disintegration process is specifically critical for immediate-release dosage forms. Its mechanisms and the factors impacting disintegration are discussed and methods used to study the disintegration in-situ are presented. This review further summarises mathematical models used to simulate disintegration phenomena and to predict drug release kinetics.

Improving low fat meatball characteristics by adding whey powder.

PubMed

Serdaroğlu, Meltem

2006-01-01

In this study whey powder (WP) at levels of 0%, 2% and 4% was added to beef meatballs formulated with 5%, 10% and 20% fat levels. Raw and cooked meatballs were analyzed for protein, fat, moisture, ash and pH. Meatballs were evaluated for cooking characteristics, juiciness, colour parameters (L*,a*,b*) and sensory properties. Addition of WP did not affect fat and protein contents of meatballs. Addition of 2% or 4% WP significantly increased cooking yield regardless of the fat level. Both fat level and WP level significantly affected fat retention values of meatballs. Incorporating WP had no effect on meatball juiciness. Addition of WP increased fat and moisture retention of meatballs. Twenty percent fat resulted in higher L* and lower a* values. Adding WP resulted in higher L* values but WP had no effect on a* and b* values. WP had no detrimental effect on sensory properties.

Influence of combinations of fenugreek, garlic, and black pepper powder on production traits of the broilers

PubMed Central

Kirubakaran, A.; Moorthy, M.; Chitra, R.; Prabakar, G.

2016-01-01

Aim: To study the effects of combinations of fenugreek (Trigonella foenum-graecum L.), garlic (Allium sativum), and black pepper (Piper nigrum) powder supplementation on production traits of broiler chickens. Materials and Methods: A total of 288 commercial broiler chicks were randomly assigned to 1-9 groups with 4 replicates each. An experiment was conducted in broilers with different feed formulations; control feed, with no added fenugreek, garlic, and black pepper powder; and 8 treatment groups receiving feed supplemented with different combinations of fenugreek, garlic, and black pepper powder. The individual broilers’ body weight and feed consumption were recorded and calculate the body weight gain and feed conversion ratio (FCR). Results: Broiler’s weight gain and FCR were significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). Cumulative feed consumption was significantly higher in groups receiving feed supplemented with garlic and black pepper powder combinations (p<0.01). Conclusion: The combination of garlic and black pepper powder supplemented broiler feed fed groups showed higher production performance. The 5 g/kg garlic powder+1 g/kg black pepper powder and 10 g/kg garlic powder+2 g/kg black pepper powder significantly improved the weight gain and FCR. PMID:27284222

Influences of iron and calcium carbonate on wastewater treatment performances of algae based reactors.

PubMed

Zhao, Zhimiao; Song, Xinshan; Wang, Wei; Xiao, Yanping; Gong, Zhijie; Wang, Yuhui; Zhao, Yufeng; Chen, Yu; Mei, Mengyuan

2016-09-01

The influences of iron and calcium carbonate (CaCO3) addition in wastewater treatments reactors performance were investigated. Adding different concentrations of Fe(3+) (5, 10, 30 and 50mmol/m(3)), iron and CaCO3 powder led to changes in algal characteristics and physico-chemical and microbiological properties. According to the investigation results, nutrient removal efficiency in algae based reactors was obviously increased by the addition of 10mmol/m(3) Fe(3+), iron (5mmol/m(3)) and CaCO3 powder (0.2gm(-3)) and the removal efficiencies of BOD5, TN, and TP in Stage 2 were respectively increased by 28%, 8.9%, and 22%. The improvements in physico-chemical performances were verified by microbial community tests (bacteria quantity, activity and community measured in most probable number, extracellular enzymes activity, and Biolog Eco Plates). Microbial variations indicated the coexistence of Fe ions and carbonate-bicarbonate, which triggered the synergistic effect of physico-chemical action and microbial factors in algae based reactors. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sintering Behavior of Spark Plasma Sintered SiC with Si-SiC Composite Nanoparticles Prepared by Thermal DC Plasma Process

NASA Astrophysics Data System (ADS)

Yu, Yeon-Tae; Naik, Gautam Kumar; Lim, Young-Bin; Yoon, Jeong-Mo

2017-11-01

The Si-coated SiC (Si-SiC) composite nanoparticle was prepared by non-transferred arc thermal plasma processing of solid-state synthesized SiC powder and was used as a sintering additive for SiC ceramic formation. Sintered SiC pellet was prepared by spark plasma sintering (SPS) process, and the effect of nano-sized Si-SiC composite particles on the sintering behavior of micron-sized SiC powder was investigated. The mixing ratio of Si-SiC composite nanoparticle to micron-sized SiC was optimized to 10 wt%. Vicker's hardness and relative density was increased with increasing sintering temperature and holding time. The relative density and Vicker's hardness was further increased by reaction bonding using additional activated carbon to the mixture of micron-sized SiC and nano-sized Si-SiC. The maximum relative density (97.1%) and Vicker's hardness (31.4 GPa) were recorded at 1800 °C sintering temperature for 1 min holding time, when 0.2 wt% additional activated carbon was added to the mixture of SiC/Si-SiC.

Particle Size Effects on Flow Properties of PS304 Plasma Spray Feedstock Powder Blend

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.; DellaCorte, Christopher; Eylon, Daniel

2002-01-01

The effects of BaF2-CaF2 particle size and size distribution on PS304 feedstock powder flowability have been investigated. Angular BaF2-CaF2 eutectic powders were produced by comminution and classified by screening to obtain 38 to 45 microns 45 to 106 microns, 63 to 106 microns, 45 to 53 microns, 63 to 75 microns, and 90 to 106 microns particle size distributions. The fluorides were added incrementally from 0 to 10 wt% to the other powder constituents of the PS304 feedstock: nichrome, chromia, and silver powders. The flow rate of the powder blends decreased linearly with increasing concentration of the fluorides. Flow was degraded with decreasing BaF2-CaF2 particle size and with increasing BaF2-CaF2 particle size distribution. A semiempirical relationship is offered to describe the PS304 powder blend flow behavior. The Hausner Ratio confirmed the funnel flow test results, but was slightly less sensitive to differences in BaF2-CaF2 particle size and size distribution. These findings may have applicability to other powders that do not flow easily, such as ceramic powders.

Inverse Catalysts for CO Oxidation: Enhanced Oxide–Metal Interactions in MgO/Au(111), CeO 2/Au(111), and TiO 2/Au(111)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palomino, Robert M.; Gutiérrez, Ramón A.; Liu, Zongyuan

Au(111) does not bind CO and O 2 well. The deposition of small nanoparticles of MgO, CeO 2, and TiO 2 on Au(111) produces excellent catalysts for CO oxidation at room temperature. In an inverse oxide/metal configuration there is a strong enhancement of the oxide–metal interactions, and the inverse catalysts are more active than conventional Au/MgO(001), Au/CeO 2(111), and Au/TiO 2(110) catalysts. An identical trend was seen after comparing the CO oxidation activity of TiO2/Au and Au/TiO 2 powder catalysts. In the model systems, the activity increased following the sequence: MgO/Au(111) < CeO 2/Au(111) < TiO 2/Au(111). Ambient pressure X-raymore » photoelectron spectroscopy (AP-XPS) was used to elucidate the role of the titania–gold interface in inverse TiO 2/Au(111) model catalysts during CO oxidation. Stable surface intermediates such as CO(ads), CO 3 2–(ads), and OH(ads) were identified under reaction conditions. CO 3 2–(ads) and OH(ads) behaved as spectators. The concentration of CO(ad) initially increased and then decreased with increasing TiO 2 coverage, demonstrating a clear role of the Ti–Au interface and the size of the TiO 2 nanostructures in the catalytic process. Overall, our results show an enhancement in the strength of the oxide–metal interactions when working with inverse oxide/metal configurations, a phenomenon that can be utilized for the design of efficient catalysts useful for green and sustainable chemistry.« less

Inverse Catalysts for CO Oxidation: Enhanced Oxide–Metal Interactions in MgO/Au(111), CeO 2/Au(111), and TiO 2/Au(111)

DOE PAGES

Palomino, Robert M.; Gutiérrez, Ramón A.; Liu, Zongyuan; ...

2017-09-26

Au(111) does not bind CO and O 2 well. The deposition of small nanoparticles of MgO, CeO 2, and TiO 2 on Au(111) produces excellent catalysts for CO oxidation at room temperature. In an inverse oxide/metal configuration there is a strong enhancement of the oxide–metal interactions, and the inverse catalysts are more active than conventional Au/MgO(001), Au/CeO 2(111), and Au/TiO 2(110) catalysts. An identical trend was seen after comparing the CO oxidation activity of TiO2/Au and Au/TiO 2 powder catalysts. In the model systems, the activity increased following the sequence: MgO/Au(111) < CeO 2/Au(111) < TiO 2/Au(111). Ambient pressure X-raymore » photoelectron spectroscopy (AP-XPS) was used to elucidate the role of the titania–gold interface in inverse TiO 2/Au(111) model catalysts during CO oxidation. Stable surface intermediates such as CO(ads), CO 3 2–(ads), and OH(ads) were identified under reaction conditions. CO 3 2–(ads) and OH(ads) behaved as spectators. The concentration of CO(ad) initially increased and then decreased with increasing TiO 2 coverage, demonstrating a clear role of the Ti–Au interface and the size of the TiO 2 nanostructures in the catalytic process. Overall, our results show an enhancement in the strength of the oxide–metal interactions when working with inverse oxide/metal configurations, a phenomenon that can be utilized for the design of efficient catalysts useful for green and sustainable chemistry.« less

PROCESSING OF RADIOACTIVE WASTE

DOEpatents

Johnson, B.M. Jr.; Barton, G.B.

1961-11-14

A process for treating radioactive waste solutions prior to disposal is described. A water-soluble phosphate, borate, and/or silicate is added. The solution is sprayed with steam into a space heated from 325 to 400 deg C whereby a powder is formed. The powder is melted and calcined at from 800 to 1000 deg C. Water vapor and gaseous products are separated from the glass formed. (AEC)

Short-term effect of the soil amendments activated carbon, biochar, and ferric oxyhydroxide on bacteria and invertebrates.

PubMed

Hale, Sarah E; Jensen, John; Jakob, Lena; Oleszczuk, Patryk; Hartnik, Thomas; Henriksen, Thomas; Okkenhaug, Gudny; Martinsen, Vegard; Cornelissen, Gerard

2013-08-06

The aim of the present study was to evaluate the secondary ecotoxicological effects of soil amendment materials that can be added to contaminated soils in order to sequester harmful pollutants. To this end, a nonpolluted agricultural soil was amended with 0.5, 2, and 5% of the following four amendments: powder activated carbon (PAC), granular activated carbon, corn stover biochar, and ferric oxyhydroxide powder, which have previously been proven to sequester pollutants in soil. The resulting immediate effects (i.e., without aging the mixtures before carrying out tests) on the springtail Folsomia candida, the earthworm species Aporectodea caliginosa and Eisenia fetida, the marine bacteria Vibrio fischeri, a suite of ten prokaryotic species, and a eukaryote (the yeast species Pichia anomalia) were investigated. Reproduction of F. candida was significantly increased compared to the unamended soil when 2% biochar was added to it. None of the treatments caused a negative effect on reproduction. All amendments had a deleterious effect on the growth of A. caliginosa when compared to the unamended soil, except the 0.5% amendment of biochar. In avoidance tests, E. fetida preferred biochar compared to all other amendments including the unamended soil. All amendments reduced the inhibition of luminescence to V. fischeri, i.e., were beneficial for the bacteria, with PAC showing the greatest improvement. The effects of the amendments on the suite of prokaryotic species and the eukaryote were variable, but overall the 2% biochar dose provided the most frequent positive effect on growth. It is concluded that the four soil amendments had variable but never strongly deleterious effects on the bacteria and invertebrates studied here during the respective recommended experimental test periods.

In vitro bioactivity and antimicrobial tuning of bioactive glass nanoparticles added with neem (Azadirachta indica) leaf powder.

PubMed

Prabhu, M; Ruby Priscilla, S; Kavitha, K; Manivasakan, P; Rajendran, V; Kulandaivelu, P

2014-01-01

Silica and phosphate based bioactive glass nanoparticles (58SiO2-33CaO-9P2O5) with doping of neem (Azadirachta indica) leaf powder and silver nanoparticles were prepared and characterised. Bioactive glass nanoparticles were produced using sol-gel technique. In vitro bioactivity of the prepared samples was investigated using simulated body fluid. X-ray diffraction (XRD) pattern of prepared glass particles reveals amorphous phase and spherical morphology with a particle size of less than 50 nm. When compared to neem doped glass, better bioactivity was attained in silver doped glass through formation of hydroxyapatite layer on the surface, which was confirmed through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analysis. However, neem leaf powder doped bioactive glass nanoparticles show good antimicrobial activity against Staphylococcus aureus and Escherichia coli and less bioactivity compared with silver doped glass particles. In addition, the biocompatibility of the prepared nanocomposites reveals better results for neem doped and silver doped glasses at lower concentration. Therefore, neem doped bioactive glass may act as a potent antimicrobial agent for preventing microbial infection in tissue engineering applications.

Real-time assessment of critical quality attributes of a continuous granulation process.

PubMed

Fonteyne, Margot; Vercruysse, Jurgen; Díaz, Damián Córdoba; Gildemyn, Delphine; Vervaet, Chris; Remon, Jean Paul; De Beer, Thomas

2013-02-01

There exists the intention to shift pharmaceutical manufacturing of solid dosage forms from traditional batch production towards continuous production. The currently applied conventional quality control systems, based on sampling and time-consuming off-line analyses in analytical laboratories, would annul the advantages of continuous processing. It is clear that real-time quality assessment and control is indispensable for continuous production. This manuscript evaluates strengths and weaknesses of several complementary Process Analytical Technology (PAT) tools implemented in a continuous wet granulation process, which is part of a fully continuous from powder-to-tablet production line. The use of Raman and NIR-spectroscopy and a particle size distribution analyzer is evaluated for the real-time monitoring of critical parameters during the continuous wet agglomeration of an anhydrous theophylline- lactose blend. The solid state characteristics and particle size of the granules were analyzed in real-time and the critical process parameters influencing these granule characteristics were identified. The temperature of the granulator barrel, the amount of granulation liquid added and, to a lesser extent, the powder feed rate were the parameters influencing the solid state of the active pharmaceutical ingredient (API). A higher barrel temperature and a higher powder feed rate, resulted in larger granules.

In Vitro Bioactivity and Antimicrobial Tuning of Bioactive Glass Nanoparticles Added with Neem (Azadirachta indica) Leaf Powder

PubMed Central

Prabhu, M.; Ruby Priscilla, S.; Kavitha, K.; Manivasakan, P.; Rajendran, V.; Kulandaivelu, P.

2014-01-01

Silica and phosphate based bioactive glass nanoparticles (58SiO2-33CaO-9P2O5) with doping of neem (Azadirachta indica) leaf powder and silver nanoparticles were prepared and characterised. Bioactive glass nanoparticles were produced using sol-gel technique. In vitro bioactivity of the prepared samples was investigated using simulated body fluid. X-ray diffraction (XRD) pattern of prepared glass particles reveals amorphous phase and spherical morphology with a particle size of less than 50 nm. When compared to neem doped glass, better bioactivity was attained in silver doped glass through formation of hydroxyapatite layer on the surface, which was confirmed through XRD, Fourier transform infrared (FTIR), and scanning electron microscopy (SEM) analysis. However, neem leaf powder doped bioactive glass nanoparticles show good antimicrobial activity against Staphylococcus aureus and Escherichia coli and less bioactivity compared with silver doped glass particles. In addition, the biocompatibility of the prepared nanocomposites reveals better results for neem doped and silver doped glasses at lower concentration. Therefore, neem doped bioactive glass may act as a potent antimicrobial agent for preventing microbial infection in tissue engineering applications. PMID:25276834

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1994-01-01

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1995-01-01

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft.

Associations between fluorosis of permanent incisors and fluoride intake from infant formula, other dietary sources and dentifrice during early childhood

PubMed Central

Levy, Steven M.; Broffitt, Barbara; Marshall, Teresa A.; Eichenberger-Gilmore, Julie M.; Warren, John J.

2017-01-01

Objectives The authors describe associations between dental fluorosis and fluoride intakes, with an emphasis on intake from fluoride in infant formula. Methods The authors administered periodic questionnaires to parents to assess early fluoride intake sources from beverages, selected foods, dentifrice and supplements. They assessed relationships between fluorosis of the permanent maxillary incisors and fluoride intake from beverages and other sources, both for individual time points and cumulatively using area-under-the-curve (AUC) estimates. The authors determined effects associated with fluoride in reconstituted powdered infant formulas, along with risks associated with intake of fluoride from dentifrice and other sources. Results Considering only fluoride intake from age 3 to 9 months, the authors found that participants with fluorosis (97 percent of which was mild) had significantly greater cumulative fluoride intake (AUC) from reconstituted powdered infant formula, other beverages with added water or a combination of these than did those without fluorosis. For participants aged 16 to 36 months, participants with fluorosis had significantly higher fluoride intake from water by itself, dentifrice or a combination of these than did those without fluorosis. In a model combining both the 3- to 9-month and 16- to 36-months age groups, the significant variables were fluoride intake from reconstituted powder concentrate formula (by participants aged 3–9 months), other beverages with added water (also by participants aged 3–9 months) and dentifrice (by participants aged 16–36 months). Conclusions Greater fluoride intakes from reconstituted powdered formulas (when participants were aged 3–9 months) and other water-added beverages (when participants were aged 3–9 months) increased fluorosis risk as did higher dentifrice intake by participants when aged 16 to 36 months. Clinical Implications Results suggest that prevalence of mild dental fluorosis could be reduced by avoiding ingestion of large quantities of fluoride from reconstituted powdered concentrate infant formula and fluoridated dentifrice. PMID:20884921

Roller compaction of different pseudopolymorphic forms of theophylline: Effect on compressibility and tablet properties.

PubMed

Hadzović, Ervina; Betz, Gabriele; Hadzidedić, Seherzada; El-Arini, Silvia Kocova; Leuenberger, Hans

2010-08-30

The effect of roller compaction on disintegration time, dissolution rate and compressibility of tablets prepared from theophylline anhydrate powder, theophylline anhydrate fine powder and theophylline monohydrate was studied. In addition, the influence of adding microcrystalline cellulose, a commonly used excipient, in mixtures with these materials was investigated. Theophylline anhydrate powder was used as a model drug to investigate the influence of different compaction pressures on the tablet properties. Tablets with same porosity were prepared by direct compaction and by roller compaction/re-compaction. Compressibility was characterized by Heckel and modified Heckel equations. Due to the property of polymorphic materials to change their form during milling and compression, X-ray diffraction analysis of theophylline anhydrate powder, theophylline anhydrate fine powder and theophylline monohydrate powders and granules was carried out. After roller compaction the disintegration time and the dissolution rate of the tablets were significantly improved. Compressibility of theophylline anhydrate powder and theophylline anhydrate fine powder was decreased, while theophylline monohydrate showed higher compressibility after roller compaction. Microcrystalline cellulose affected compressibility of theophylline anhydrate powder, theophylline anhydrate fine powder and theophylline monohydrate whereby the binary mixtures showed higher compressibility than the individual materials. X-ray diffraction analyses confirmed that there were no polymorphic/pseudopolymorphic changes after roller compaction. Copyright 2010 Elsevier B.V. All rights reserved.

Electrochemical performance of NCM/LFP/Al composite cathode materials for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Allahyari, Ehsan; Ghorbanzadeh, Milad; Riahifar, Reza; Hadavi, S. M. M.

2018-05-01

The LiNi0.5Mn0.3Co0.2O2 (NCM) was synthesized via conventional solution combustion synthesis method. Different amounts of LiFePO4 (10, 20 and 30 wt%) were added to NCM via the ball milling technique to improve electrochemical performance including discharge capacity, cycle stability, and rate capability. The LiNi0.5Mn0.3Co0.2O2/LiFePO4 containing 20 wt% LiFePO4 was considered as the optimum composition according to the electrochemical results and SEM images. The Al powder was added to optimum LiNi0.5Mn0.3Co0.2/LiFePO4-0.2 composite through planetary ball mill to enhance the conductivity of LiNi0.5Mn0.3Co0.2O2/LiFePO4-0.2. The LiNi0.5Mn0.3Co0.2O2/LiFePO4-0.2/Al composite cathodes provide better electrochemical performance compared to pure LiNi0.5Mn0.3Co0.2O2 cathodes. The results indicate that by addition of 20 wt% of LiFePO4, the internal resistance of the electrode as well as the charge transfer resistance are reduced. Due to the strong P–O bond of the PO4 in LiFePO4, side reactions between the active electrode and electrolyte is prevented. In addition, according to weakness of the Ionic conductivity in solid electrolyte, in this paper aluminum powders added to the electrode for resolving this problem.

Functional properties of roselle (Hibiscus sabdariffa L.) seed and its application as bakery product.

PubMed

Nyam, Kar-Lin; Leao, Sod-Ying; Tan, Chin-Ping; Long, Kamariah

2014-12-01

Roselle (Hibiscus sabdariffa L.) seed is a valuable food resource as it has an excellent source of dietary fibre. Therefore, this study examined the functional properties of roselle seeds. Replacement of cookie flour with roselle seed powder at levels of 0-30 % was investigated for its effect on functional and nutritional properties of cookies. Among the four formulations cookies, the most preferred by panelists was 20 % roselle seed powder cookie (F3), followed by 10 % roselle seed powder cookie (F2) and 30 % roselle seed powder cookie (F4). The least preferred formulation among all was control cookie (F1). Cookie with 20 % roselle seed powder added showed higher content of total dietary fibre (5.6 g/100 g) as compared with control cookie (0.90 g/100 g). Besides that, cookies incorporated with roselle seed powder exhibited improved antioxidant properties. Thus, roselle seed powder can be used as a dietary fibre source and developed as a functional ingredient in food products.

Small Arms Powder Manufacture in Germany

DTIC Science & Technology

1945-10-16

used were as follows: A. Nit ro--cellulose. B. Diphenylamine. C. Alcohol and Ether. D. Graphite. "E. Camphor . F. Contralite. G. Pottasium Sulfate. -3...about the other raw materials used. Graphite, camphor and centralite were added as.coat.ing materials. The potassium sulfate served as a flash...warm for 2 (two) hours. Centralit I is used on all powders, sometimes in conjunction with Diamylphthalate (Amylol) or camphor . The amount of

FUEL COMPOSITION FOR NUCLEAR REACTORS

DOEpatents

Andersen, J.C.

1963-08-01

A process for making refractory nuclear fuel elements involves heating uranium and silicon powders in an inert atmosphere to 1600 to 1800 deg C to form USi/sub 3/; adding silicon carbide, carbon, 15% by weight of nickel and aluminum, and possibly also molybdenum and silicon powders; shaping the mixture; and heating to 1700 to 2050 deg C again in an inert atmosphere. Information on obtaining specific compositions is included. (AEC)

Physical evaluation of a maize-based extruded snack with curry powder.

PubMed

Christofides, Vassilis; Ainsworth, Paul; Ibanoğlu, Senol; Gomes, Frances

2004-02-01

Response surface methodology was used to analyze the effect of screw speed (200-280 rpm), feed moisture (13.0-17.0%, wet basis), and curry powder (6.0-9.0%) on the bulk density, lateral expansion, and firmness of maize-based extruded snack with curry powder. Regression equations describing the effect of each variable on the responses were obtained. Responses were most affected by changes in feed moisture followed by screw speed and curry powder (p < 0.05). Lateral expansion increased linearly as the amount of curry powder added was increased whereas a quadratic increase was obtained in lateral expansion with decreasing feed moisture. The firmness of samples was increased with an increase in feed moisture. The bulk density of samples was increased with increasing feed moisture and screw speeds. Radial expansion was found to be a better index to measure the physical properties of the extruded product indicated by a higher correlation coefficient.

Effect of ZrO2 Powders on the Pyrolysis of Polycarbosilanes Coating Under Laser Ablation

NASA Astrophysics Data System (ADS)

Cheng, Han; Chen, Zhaofeng; Tao, Jie; Yan, Bo; Li, Cong; Wang, Liangbing; Zhang, Ying; Fang, Dan; Wan, Shuicheng; Wu, Wangping

Aircrafts hold the outstanding mastery of the sky in modern wars, however the laser beam weapons can carry out laser attacking to aircrafts. The purpose of the present paper is to research on a new type laser protective material. Polycarbosilanes (PCS)/divinylbenzene mixtures containing ZrO2 powders were brushed to the surface of the aluminum alloy plates and then cured at 150°C for 6 h. The PCS-coated plates were ablated by laser for 3 s. The phase identification of as-ablated powders was examined by X-ray diffraction. The results indicated that the as-ablated powders of cured PCS were composed of major phase β-SiC and smaller amounts of free carbon. The PCS composite coating played a certain role of laser ablation resistance. The effect of added ZrO2 powders on the pyrolysis of PCS-coating under laser ablation is conspicuous.

Chemically bonded phospho-silicate ceramics

DOEpatents

Wagh, Arun S.; Jeong, Seung Y.; Lohan, Dirk; Elizabeth, Anne

2003-01-01

A chemically bonded phospho-silicate ceramic formed by chemically reacting a monovalent alkali metal phosphate (or ammonium hydrogen phosphate) and a sparsely soluble oxide, with a sparsely soluble silicate in an aqueous solution. The monovalent alkali metal phosphate (or ammonium hydrogen phosphate) and sparsely soluble oxide are both in powder form and combined in a stochiometric molar ratio range of (0.5-1.5):1 to form a binder powder. Similarly, the sparsely soluble silicate is also in powder form and mixed with the binder powder to form a mixture. Water is added to the mixture to form a slurry. The water comprises 50% by weight of the powder mixture in said slurry. The slurry is allowed to harden. The resulting chemically bonded phospho-silicate ceramic exhibits high flexural strength, high compression strength, low porosity and permeability to water, has a definable and bio-compatible chemical composition, and is readily and easily colored to almost any desired shade or hue.

Method for forming porous sintered bodies with controlled pore structure

DOEpatents

Whinnery, LeRoy Louis; Nichols, Monte Carl

2000-01-01

The present invention is based, in part, on a method for combining a mixture of hydroxide and hydride functional siloxanes to form a polysiloxane polymer foam, that leaves no residue (zero char yield) upon thermal decomposition, with ceramic and/or metal powders and appropriate catalysts to produce porous foam structures having compositions, densities, porosities and structures not previously attainable. The siloxanes are mixed with the ceramic and/or metal powder, wherein the powder has a particle size of about 400 .mu.m or less, a catalyst is added causing the siloxanes to foam and crosslink, thereby forming a polysiloxane polymer foam having the metal or ceramic powder dispersed therein. The polymer foam is heated to thermally decompose the polymer foam and sinter the powder particles together. Because the system is completely nonaqueous, this method further provides for incorporating reactive metals such as magnesium and aluminum, which can be further processed, into the foam structure.

Effects of Humidity On the Flow Characteristics of PS304 Plasma Spray Feedstock Powder Blend

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.; DellaCorte, Christopher

2002-01-01

The effects of environmental humidity on the flow characteristics of PS304 feedstock have been investigated. Angular and spherical BaF2-CaF2 powder was fabricated by comminution and by atomization, respectively. The fluorides were added incrementally to the nichrome, chromia, and silver powders to produce PS304 feedstock. The powders were dried in a vacuum oven and cooled to a Tom temperature under dry nitrogen. The flow of the powder was studied from 2 to 100 percent relative humidity (RH) The results suggest that the feedstock flow is slightly degraded with increasing humidity below 66 percent RH and is more affected above 66 percent RH. There was no flow above 88 percent RH. Narrower particle size distributions of the angular fluorides allowed flow up to 95 percent RH. These results offer guidance that enhances the commercial potential for this material system.

Use of limestone powder during incorporation of Pb-containing cathode ray tube waste in self-compacting concrete.

PubMed

Sua-iam, Gritsada; Makul, Natt

2013-10-15

For several decades, cathode ray tubes (CRTs) were the primary display component of televisions and computers. The CRT glass envelope contains sufficient levels of lead oxide (PbO) to be considered hazardous, and there is a need for effective methods of permanently encapsulating this material during waste disposal. We examined the effect of adding limestone powder (LS) on the fresh and cured properties of self-compacting concrete (SCC) mixtures containing waste CRT glass. The SCC mixtures were prepared using Type 1 Portland cement at a constant cement content of 600 kg/m(3) and a water-to-cement ratio (w/c) of 0.38. CRT glass waste cullet was blended with river sand in proportions of 20 or 40% by weight. To suppress potential viscosity effects limestone powder was added at levels of 5, 10, or 15% by weight. The slump flow time, slump flow diameter, V-funnel flow time, Marsh cone flow time, and setting time of the fresh concrete were tested, as well as the compressive strength and ultrasonic pulse velocity of the hardened concrete. Addition of limestone powder improved the fresh and hardened properties. Pb leaching levels from the cured concrete were within US EPA allowable limits. Copyright © 2013 Elsevier Ltd. All rights reserved.

The reduction of graphene oxide by zinc powder to produce a zinc oxide-reduced graphene oxide hybrid and its superior photocatalytic activity

NASA Astrophysics Data System (ADS)

Sarkar, Sanjit; Basak, Durga

2013-03-01

We have synthesized for the first time ZnO/rGO hybrids from metal zinc and GO using hydrothermal technique without adding further reducing agent. The photocatalytic property of ZnO-rGO reveals that the hybrid for 50 mg of GO has the highest activity, causing a 94% degradation of methyl orange compared to 70% by only ZnO. The consistent quenching and a gradual decrease in the decay life time of the emission at ˜500 nm as the rGO content increases indicates the interfacial charge transfer process between ZnO and rGO by the defect states responsible for green emission.

The effect of oyster mushroom (Pleurotus ostreatus) powder as prebiotic agent on yoghurt quality

NASA Astrophysics Data System (ADS)

Tupamahu, Ivana Putri Christantia; Budiarso, Tri Yahya

2017-05-01

Mushroom has already been known as a good source of proteins, carbohydrates and some vitamins. It is then the objective of this research to find out the effect of oyster mushroom (Pleurotus ostreatus) powder addition on yoghurt fermentation. The resulting yoghurt product will be monitor by measuring its total lactic acids, acidity (pH), lactic acid bacteria (LAB) count, and the organoleptic properties, including colour, taste, flavour and texture. The mushroom were dried and grinded into powder up to 200 mashes, continued with its addition in yoghurt making process. Mushroom powder concentrations of 0%, 0.5%, 1%, and 1.5% were added on the milk to be fermented. The result showed that mushroom powder addition resulting in increase lactic acid concentration, reduced its acidity, and increased LAB viability. Based on the lactic acid counts, acidity, and LAB viability, a concentration of 1.5% powder addition is the optimal concentration for fermentation, but the product is not preferred by the panelists. The addition of 1% mushroom powder resulting in increased yoghurt quality, and the preferred yoghurt product by most of the panelists. It is then proven that the addition of mushroom powder will increase yoghurt quality and public acceptance.

PROCESS OF FORMING POWDERED MATERIAL

DOEpatents

Glatter, J.; Schaner, B.E.

1961-07-14

A process of forming high-density compacts of a powdered ceramic material is described by agglomerating the powdered ceramic material with a heat- decompossble binder, adding a heat-decompossble lubricant to the agglomerated material, placing a quantity of the material into a die cavity, pressing the material to form a compact, pretreating the compacts in a nonoxidizing atmosphere to remove the binder and lubricant, and sintering the compacts. When this process is used for making nuclear reactor fuel elements, the ceramic material is an oxide powder of a fissionsble material and after forming, the compacts are placed in a cladding tube which is closed at its ends by vapor tight end caps, so that the sintered compacts are held in close contact with each other and with the interior wall of the cladding tube.

Process for production of solution-derived (Pb,La)(Nb,Sn,Zr,Ti)O{sub 3} thin films and powders

DOEpatents

Boyle, T.J.

1999-01-12

A simple and rapid process for synthesizing (Pb,La)(Nb,Sn,Zr,Ti)O{sub 3} precursor solutions and subsequent ferroelectric thin films and powders of the perovskite phase of these materials has been developed. This process offers advantages over standard methods, including: rapid solution synthesis (<10 minutes), use of commercially available materials, film production under ambient conditions, ease of lanthanum dissolution at high concentrations, and no heating requirements during solution synthesis. For lanthanum-doped ferroelectric materials, the lanthanum source can be added with total synthesis time less than 10 minutes. Films and powders are crystallized at approximately 650 C and exhibit ferroelectric properties comparable to films and powders produced by other techniques which require higher crystallization temperatures. 2 figs.

Process for production of solution-derived (Pb,La)(Nb,Sn,Zr,Ti)O.sub.3 thin films and powders

DOEpatents

Boyle, Timothy J.

1999-01-01

A simple and rapid process for synthesizing (Pb,La)(Nb,Sn,Zr,Ti)O.sub.3 precursor solutions and subsequent ferroelectric thin films and powders of the perovskite phase of these materials has been developed. This process offers advantages over standard methods, including: rapid solution synthesis (<10 minutes), use of commercially available materials, film production under ambient conditions, ease of lanthanum dissolution at high concentrations, and no heating requirements during solution synthesis. For lanthanum-doped ferroelectric materials, the lanthanum source can be added with total synthesis time less than 10 minutes. Films and powders are crystallized at approximately 650.degree. C. and exhibit ferroelectric properties comparable to films and powders produced by other techniques which require higher crystallization temperatures.

Isolation of levoglucosan from pyrolysis oil derived from cellulose

DOEpatents

Moens, Luc

1994-01-01

High purity levoglucosan is obtained from pyrolysis oil derived from cellulose by: mixing pyrolysis oil with water and a basic metal hydroxide, oxide, or salt in amount sufficient to elevate pH values to a range of from about 12 to about 12.5, and adding an amount of the hydroxide, oxide, or salt in excess of the amount needed to obtain the pH range until colored materials of impurities from the oil are removed and a slurry is formed; drying the slurry azeotropically with methyl isobutyl ketone solvent to form a residue, and further drying the residue by evaporation; reducing the residue into a powder; continuously extracting the powder residue with ethyl acetate to provide a levoglucosan-rich extract; and concentrating the extract by removing ethyl acetate to provide crystalline levoglucosan. Preferably, Ca(OH).sub.2 is added to adjust the pH to the elevated values, and then Ca(OH).sub.2 is added in an excess amount needed.

Isolation of levoglucosan from pyrolysis oil derived from cellulose

DOEpatents

Moens, L.

1994-12-06

High purity levoglucosan is obtained from pyrolysis oil derived from cellulose by: mixing pyrolysis oil with water and a basic metal hydroxide, oxide, or salt in amount sufficient to elevate pH values to a range of from about 12 to about 12.5, and adding an amount of the hydroxide, oxide, or salt in excess of the amount needed to obtain the pH range until colored materials of impurities from the oil are removed and a slurry is formed; drying the slurry azeotropically with methyl isobutyl ketone solvent to form a residue, and further drying the residue by evaporation; reducing the residue into a powder; continuously extracting the powder residue with ethyl acetate to provide a levoglucosan-rich extract; and concentrating the extract by removing ethyl acetate to provide crystalline levoglucosan. Preferably, Ca(OH)[sub 2] is added to adjust the pH to the elevated values, and then Ca(OH)[sub 2] is added in an excess amount needed. 3 figures.

Reducing retrogradation and lipid oxidation of normal and glutinous rice flours by adding mango peel powder.

PubMed

Siriamornpun, Sirithon; Tangkhawanit, Ekkarat; Kaewseejan, Niwat

2016-06-15

Green and ripe mango peel powders (MPP) were added to normal rice flour (NRF) and glutinous rice flour (GRF) at three levels (400, 800 and 1200 ppm) and their effects on physicochemical properties and lipid oxidation inhibition were investigated. Overall, MPP increased the breakdown viscosity and reduced the final viscosity in rice flours when compared to the control. Decreasing in retrogradation was observed in both NRF and GRF with MPP added of all levels. MPP addition also significantly inhibited the lipid oxidation of all flours during storage (30 days). Retrogradation values were strongly negatively correlated with total phenolic and flavonoid contents, but not with fiber content. The hydrogen bonds and hydrophilic interactions between phenolic compounds with amylopectin molecule may be involved the decrease of starch retrogradation, especially GRF. We suggest that the addition of MPP not only reduced the retrogradation but also inhibited the lipid oxidation of rice flour. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

NASA Astrophysics Data System (ADS)

Karim, Ahmad Fikri Abdul; Ismail, Hanafi; Ariff, Zulkifli Mohamad

2015-07-01

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM).

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1995-12-26

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figs.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1994-12-06

A free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and particularly in applications for heat protection for heat sensitive items, such as aircraft flight recorders, and for preventing brake fade in automobiles, buses, trucks and aircraft. 3 figures.

Hydrogen Decrepitation Press-Less Process recycling of NdFeB sintered magnets

NASA Astrophysics Data System (ADS)

Xia, Manlong; Abrahamsen, Asger B.; Bahl, Christian R. H.; Veluri, Badrinath; Søegaard, Allan I.; Bøjsøe, Poul

2017-11-01

A Hydrogen Decrepitation Press-Less Process (HD-PLP) recycling method for recycling of anisotropic NdFeB magnets is demonstrated. The method combines hydrogen decrepitation (HD) disintegration of the initial magnet, powder sieving and the Press-Less Process (PLP), where hydride powder is sintered in a graphite mold. Coercivities up to 534 kA/m were obtained in porous samples based on powder size d < 100 μm. Adding a ball milling step resulted in full density isotropic magnets for d > 100 μm. The coercivity reached Hci = 957 kA/m being 86% of the original N48M material without addition of rare earth elements.

Water Purification Systems

NASA Technical Reports Server (NTRS)

1992-01-01

A water purification/recycling system developed by Photo-Catalytics, Inc. (PCI) for NASA is commercially available. The system cleanses and recycles water, using a "photo-catalysis" process in which light or radiant energy sparks a chemical reaction. Chemically stable semiconductor powders are added to organically polluted water. The powder absorbs ultraviolet light, and pollutants are oxidized and converted to carbon dioxide. Potential markets for the system include research and pharmaceutical manufacturing applications, as well as microchip manufacture and wastewater cleansing.

Effects of La2O3 content and particle size on the long-term stability and thermal cycling property of La2O3-dispersed SUS430 alloys for SOFC interconnect materials

NASA Astrophysics Data System (ADS)

Lee, Jung-Won; Mehran, Muhammad Taqi; Song, Rak-Hyun; Lee, Seung-Bok; Lee, Jong-Won; Lim, Tak-Hyoung; Park, Seok-Joo; Hong, Jong-Eun; Shim, Joon-Hyung

2017-11-01

We developed oxide-dispersed alloys as interconnect materials for a solid oxide fuel cell by adding La2O3 to SUS430 ferritic steels. For this purpose, we prepared two types of La2O3 with different particle sizes and added different amounts of La2O3 to SUS430 powder. Then, we mixed the powders using a high energy ball mill, so that nano-sized as well as micro-sized oxide particles were able to mix uniformly with the SUS430 powders. After preparing hexahedral green samples using uni-axial and cold isostatic presses, we were finally able to obtain oxide-dispersed alloys having high relative densities after firing at 1,400 °C under hydrogen atmosphere. The nano-sized La2O3 dispersed alloys showed properties superior to those of micro-sized dispersed alloys in terms of long-term stability and thermal cycling. Moreover, we determined the optimum amounts of added La2O3. Finally we were able to develop a new oxide-dispersed alloy showing excellent properties of low area specific resistance (16.23 mΩ cm2) after 1000 h at 800 °C, and no degradation after 10 iterations of thermal cycling under oxidizing atmosphere.

Improved dielectric properties of BaTiO3-added CaCu3Ti4O12 polycrystalline ceramics

NASA Astrophysics Data System (ADS)

Kim, Hui Eun; Choi, Soon-Mi; Lee, Sung-Yun; Hong, Youn-Woo; Yoo, Sang-Im

2013-05-01

The effects of the BaTiO3 (BTO) additive on the electrical properties of CaCu3Ti4O12 (CCTO) polycrystalline ceramics were systematically investigated. Various amounts of BTO powder up to 15 mol. % were added to CCTO powder. Each batch was ball-milled, pressed into pellets, and finally sintered at 1060°C for 12 h in air. Compared with pure CCTO sample ( ɛ r ˜ 52,000 and tan δ ˜ 0.38 at 100 kHz), BTO-added CCTO samples commonly showed significantly reduced dielectric losses although their dielectric constants were decreased approximately by one order of magnitude (for instance, ɛ r ˜ 4,075 and tan δ ˜ 0.02 at 100 kHz for 5 mol. % BTO-added CCTO sample). In addition, the breakdown voltages of BTO-added CCTO samples were much higher than that of pure CCTO sample, and thus the leakage currents were greatly reduced at the applied voltage above ˜ 10 V. A large reduction in the dielectric losses and leakage currents is attributed to the secondary phases segregated at the CCTO grain boundary which are composed of CaTiO3, Ba4Ti12O27, and unreacted BTO.

Silicone azide fireproof material

NASA Technical Reports Server (NTRS)

1978-01-01

Finely powdered titanium oxide was added to silicone azide as the sintering agent to produce a nonflammable material. Mixing proportions, physical properties, and chemical composition of the fireproofing material are included.

New insights into respirable protein powder preparation using a nano spray dryer.

PubMed

Bürki, K; Jeon, I; Arpagaus, C; Betz, G

2011-04-15

In this study the Nano Spray Dryer B-90 (BÜCHI Labortechnik AG, Flawil, Switzerland) was evaluated with regard to the drying of proteins and the preparation of respirable powders in the size range of 1-5 μm. β-galactosidase was chosen as a model protein and trehalose was added as a stabilizer. The influence of inlet temperature, hole size of the spray cap membrane and ethanol concentration in the spray solution was studied using a 3³ full factorial design. The investigated responses were enzyme activity, particle size, span, yield and shelf life. Furthermore, the particle morphology was examined. The inlet temperature as well as the interaction of inlet temperature and spray cap size significantly influenced the enzyme activity. Full activity was retained with the optimized process. The particle size was affected by the hole size of the spray cap membrane and the ethanol content. The smallest cap led to a monodisperse particle size distribution and the greatest yield of particles of respirable size. Higher product recovery was achieved with lower inlet temperatures, higher ethanol contents and smaller cap sizes. Particle morphology differed depending on the cap size. The protein exhibited higher storage stability when spray dried without ethanol and when a larger spray cap size was used. Copyright © 2011 Elsevier B.V. All rights reserved.

Progress in the development of lightweight nickel electrode

NASA Technical Reports Server (NTRS)

Britton, Doris L.

1992-01-01

The use of the lightweight nickel electrode, in place of the heavy-sintered state-of-the-art nickel electrode, will lead to improvements in specific energy and performance of the nickel-hydrogen cell. Preliminary testing indicates that a nickel fiber mat is a promising support candidate for the nickel hydroxide active material. Nickel electrodes made from fiber mats, with nickel and cobalt powder added to the fiber, were tested at LeRC. To date, over 8000 cycles have been accumulated, at 40 percent depth-of-discharge, using the lightweight fiber electrode, in a boiler plate nickel-hydrogen cell.

The influence of high shear mixing on ternary dry powder inhaler formulations.

PubMed

Hertel, Mats; Schwarz, Eugen; Kobler, Mirjam; Hauptstein, Sabine; Steckel, Hartwig; Scherließ, Regina

2017-12-20

The blending process is a key step in the production of dry powder inhaler formulations, but only little is known about the influence of process parameters. This is especially true for high shear blending of ternary formulations. For this reason, this study aims to investigate the influence of high shear mixing process parameters (mixing time and rotation speed) on the fine particle fraction (FPF) of ternary mixtures when using budesonide as model drug, two different carrier materials and two different mixing orders. Prolonged mixing time and higher rotation speeds led to lower FPFs, possibly due to higher press-on forces acting on the active pharmaceutical ingredients (API). In addition, a clear correlation between the energy consumption of the blender (the energy input into the blend) and the reduction of the FPF could be shown. Furthermore blending the carrier and the fines before adding the API was also found to be favorable. Copyright © 2017 Elsevier B.V. All rights reserved.

Sintering Behavior of Spark Plasma Sintered SiC with Si-SiC Composite Nanoparticles Prepared by Thermal DC Plasma Process.

PubMed

Yu, Yeon-Tae; Naik, Gautam Kumar; Lim, Young-Bin; Yoon, Jeong-Mo

2017-11-25

The Si-coated SiC (Si-SiC) composite nanoparticle was prepared by non-transferred arc thermal plasma processing of solid-state synthesized SiC powder and was used as a sintering additive for SiC ceramic formation. Sintered SiC pellet was prepared by spark plasma sintering (SPS) process, and the effect of nano-sized Si-SiC composite particles on the sintering behavior of micron-sized SiC powder was investigated. The mixing ratio of Si-SiC composite nanoparticle to micron-sized SiC was optimized to 10 wt%. Vicker's hardness and relative density was increased with increasing sintering temperature and holding time. The relative density and Vicker's hardness was further increased by reaction bonding using additional activated carbon to the mixture of micron-sized SiC and nano-sized Si-SiC. The maximum relative density (97.1%) and Vicker's hardness (31.4 GPa) were recorded at 1800 °C sintering temperature for 1 min holding time, when 0.2 wt% additional activated carbon was added to the mixture of SiC/Si-SiC.

A material-sparing method for simultaneous determination of true density and powder compaction properties--aspartame as an example.

PubMed

Sun, Changquan Calvin

2006-12-01

True density results for a batch of commercial aspartame are highly variable when helium pycnometry is used. Alternatively, the true density of the problematic aspartame lot was obtained by fitting tablet density versus pressure data. The fitted true density was in excellent agreement with that predicted from single crystal structure. Tablet porosity was calculated from the true density and tablet apparent density. After making the necessary measurements for calculating tablet apparent density, the breaking force of each intact tablet was measured and tensile strength was calculated. With the knowledge of compaction pressure, tablet porosity and tensile strength, powder compaction properties were characterized using tabletability (tensile strength versus pressure), compactibility (tensile strength versus porosity), compressibility (porosity versus pressure) and Heckel analysis. Thus, a wealth of additional information on the compaction properties of the powder was obtained through little added work. A total of approximately 4 g of powder was used in this study. Depending on the size of tablet tooling, tablet thickness and true density, 2-10 g of powder would be sufficient for characterizing most pharmaceutical powders.

A multi-analytical approach for the characterization of powders from the Pompeii archaeological site.

PubMed

Canevali, Carmen; Gentile, Paolo; Orlandi, Marco; Modugno, Francesca; Lucejko, Jeannette Jacqueline; Colombini, Maria Perla; Brambilla, Laura; Goidanich, Sara; Riedo, Chiara; Chiantore, Oscar; Baraldi, Pietro; Baraldi, Cecilia; Gamberini, Maria Cristina

2011-10-01

Nine black powders found in Pompeii houses in three different types of bronze vessels (cylindrical theca atramentaria, unguentaries, and aryballoi) were characterized in order to assess a correspondence between the composition and the type of vessel and, possibly, to verify if these powders were inks or not. For the compositional characterization, a multi-analytical approach was adopted, which involved the use of scanning electron microscopy-energy dispersive X-ray, Fourier-transformed infrared spectroscopy, Raman, X-ray diffraction, electron paramagnetic resonance spectroscopy, thermogravimetric analysis, gas chromatography coupled with mass spectrometry (GC/MS), and pyrolysis GC/MS. Powders contained in cylindrical theca atramentaria form a homogeneous group, and their organic and inorganic compositions suggest that they were writing inks, while powders contained in unguentaries and aryballoi could have had several different uses, including writing inks and cosmetics. Furthermore, the composition profile of the powders found in cylindrical cases shows that, at 79 AD: , in Pompeii, carbon-based inks were still used for writing, and iron gall inks had not been introduced yet.

[Effects of colorants on yttria stabilized tetragonal zirconia polycrystals powder].

PubMed

Wang, Bo; Chen, Jianfeng; Zhang, Yanchun; Wang, Ru

2015-10-01

To evaluate the effect of Fe2O3 and CeO2 as colorants on yttria stabilized tetragonal zirconia poly-crystals (Y-TZP) powder. The spray granulation slurry of colored zirconia was prepared with different concentrations of Fe2O3 (0.15%) and CeO2 (4%), which were added in Y-TZP. Zirconia powder was made by spray granulation. The powder specimens were divided into three groups: uncolored zirconia, Fe2O3 (0.15%) zirconia, and CeO2 (4%) zirconia. The particle morphologies of the powder specimens were measured with a laser particle size analyzer and an optical microscope. The differences in D50 among the three groups were statistically significant (P<0.05). Group Fe2O3 showed a significant difference from groups CeO2 and uncolored zirconia (P<0.05). Group uncolored zirconia showed no significant difference from group CeO2 (P>0.05). Mostly spherical powder was observed in the three groups. Fe2O3 as a colorant can affect particles, whereas CeO2 has no effect.

Combined Effect of Kimchi Powder and Onion Peel Extract on Quality Characteristics of Emulsion Sausages Prepared with Irradiated Pork.

PubMed

Lee, Soo-Yoen; Kim, Hyun-Wook; Hwang, Ko-Eun; Song, Dong-Heon; Choi, Min-Sung; Ham, Youn-Kyung; Choi, Yun-Sang; Lee, Ju-Woon; Lee, Si-Kyung; Kim, Cheon-Jei

2015-01-01

This study was conducted to investigate the effects of kimchi powder and onion peel extract on the quality characteristics of emulsion sausage manufactured with irradiated pork. The emulsion sausages were formulated with 2% kimchi powder and/or 0.05% onion peel extract. The changes in pH value of all treatments were similar, depending on storage periods. The addition of kimchi powder increased the redness and yellowness of the emulsion sausage. The addition of onion peel extract decreased the thiobarbituric acid reactive substances value of the emulsion sausages prepared with irradiated pork. The volatile basic nitrogen value of the emulsion sausage prepared with kimchi powder was the highest, whereas that of the emulsion sausage prepared with onion peel extract was the lowest. The treatment without kimchi powder or onion peel extract and the treatments prepared with onion peel extract showed lower microbial populations than the other treatment. Sensory evaluations indicated that a higher acceptability was attained when kimchi powder was added to the emulsion sausages manufactured with irradiated pork. In conclusion, our results suggest that combined use of kimchi powder and onion peel extract could improve quality characteristics and shelf stability of the emulsion sausage formulated with irradiated pork during chilled storage.

Combined Effect of Kimchi Powder and Onion Peel Extract on Quality Characteristics of Emulsion Sausages Prepared with Irradiated Pork

PubMed Central

Choi, Yun-Sang; Lee, Ju-Woon; Lee, Si-Kyung

2015-01-01

This study was conducted to investigate the effects of kimchi powder and onion peel extract on the quality characteristics of emulsion sausage manufactured with irradiated pork. The emulsion sausages were formulated with 2% kimchi powder and/or 0.05% onion peel extract. The changes in pH value of all treatments were similar, depending on storage periods. The addition of kimchi powder increased the redness and yellowness of the emulsion sausage. The addition of onion peel extract decreased the thiobarbituric acid reactive substances value of the emulsion sausages prepared with irradiated pork. The volatile basic nitrogen value of the emulsion sausage prepared with kimchi powder was the highest, whereas that of the emulsion sausage prepared with onion peel extract was the lowest. The treatment without kimchi powder or onion peel extract and the treatments prepared with onion peel extract showed lower microbial populations than the other treatment. Sensory evaluations indicated that a higher acceptability was attained when kimchi powder was added to the emulsion sausages manufactured with irradiated pork. In conclusion, our results suggest that combined use of kimchi powder and onion peel extract could improve quality characteristics and shelf stability of the emulsion sausage formulated with irradiated pork during chilled storage. PMID:26761840

Compendium of Nitromethane Data Relevant to the Tactical Explosive System (TEXS) Program

DTIC Science & Technology

1989-04-01

reduced charge size. Confined NM in glass tubes and added silica impurities with a known particle size distribution, and used guar gum to hold silica...internal ignition test. The explosive in the pipe bomb is subjected to the action of a cen- trally located black powder (20 g) igniter. A positive...Laboratory 2800 Powder Mill Road Adelphia, MD 20783-1145 Commander U.S. Army Test and Evaluation Command ATTN: AMSTE-TE-AT, B. Hawley Aberdeen

Development of edible films based on Brazilian pine seed (Araucaria angustifolia) flour reinforced with husk powder

USDA-ARS?s Scientific Manuscript database

The aim of this study was to develop edible films based on pinhão flour reinforced with pinhão husk powder. For this, six formulations were developed using 5.0% pinhão flour with 1.5% glycerol base and adding 0.5, 1.0, 1.5, 2.0 and 2.5% of pinhão husk where the pure base served as the control. The ...

Physical properties and estimated glycemic index of protein-enriched sorghum based chips.

PubMed

Jiang, Hongrui; Hettiararchchy, Navam S; Horax, Ronny

2018-03-01

Sorghum is a gluten-free grain and more attention has been given to the nutritional properties and recently its usage as a wheat replacement in food products. In the present work, protein-enriched sorghum based snack chips, prepared from sorghum meal with soy protein isolates and soy flour to meet the final protein content of 35.7%, were produced. The effect of varying baking powder (1.5-2.5%), dough sheet thickness (0.7-1.7 mm), and baking time (6-12 min) on the physical properties of the snack chips was investigated using a central composite design of response surface methodology. Under baking temperature of 160 °C, with baking powder added, the water activity and puffiness of chips significantly increased. Baking time was the most significant factor for all the parameters detected except for puffiness. The optimized conditions of preparing protein-enriched sorghum chips were baking powder 2.5%, dough sheet thickness 0.7 mm, and baking time 7.66 min. The estimated glycemic index (eGI) of the protein-enriched sorghum chips (eGI = 59.8) was significantly lower than soybean-free sorghum chips. The gluten-free protein-enriched sorghum chips developed could be considered as protein rich with lower intermediate-glycemic index classified healthy snacks and potential commercialization.

Thermal Properties of Green Fuel Briquettes from Residue Corncobs Materials Mixed Macadamia Shell Charcoal Powder

NASA Astrophysics Data System (ADS)

Teeta, Suminya; Nachaisin, Mali; Wanish, Suchana

2017-09-01

The objective of this research was to produce green fuel briquettes from corncobs by adding macadamia shell charcoal powder. The study was sectioned into 3 parts: 1) Quality improvement of green fuel briquettes by adding macadamia; 2) Fuel property analysis based on ASTM standards and thermal fuel efficiency; and 3) Economics appropriateness in producing green fuel briquettes. This research produced green fuel briquettes using the ratio of corncobs weight and macadamia shell charcoal powder in 100:0 90:10 80:20 70:30 60:40 and 50:50 and pressing in the cold briquette machine. Fuel property analysis showed that green fuel briquettes at the ratio 50:50 produced maximum heating values at 21.06 Megajoule per kilogram and briquette density of 725.18 kilograms per cubic meter, but the percent of moisture content, volatile matter, ash, and fixed carbon were 10.09, 83.02, 2.17 and 4.72 respectively. The thermal efficiency of green fuel briquettes averaged 20.22%. Economics appropriateness was most effective where the ratio of corncobs weight to macadamia shell charcoal powder was at 50:50 which accounted for the cost per kilogram at 5.75 Baht. The net present value was at 1,791.25 Baht. Internal rate of return was at 8.62 and durations for a payback period of investment was at 1.9 years which was suitable for investment.

Identification of a gamma-irradiated ingredient (garlic powder) in Korean barbeque sauce by thermoluminescence analysis.

PubMed

Ahn, Jae-Jun; Akram, Kashif; Lee, Jeongeun; Kim, Kyong-Su; Kwon, Joong-Ho

2012-04-01

Thermoluminescence (TL) analysis was applied to identify gamma-irradiated garlic powder in Korean barbeque sauce before and after pasteurization (85 °C, 30 min), when blended in different ratios (1%, 3%, and 5%). The sauce sample with nonirradiated garlic powder gave a background glow curve. However, the sample blended with irradiated ingredient (1 and 10 kGy) showed typical TL glow curves at temperatures of 150 to 200 °C. The identification properties of sauce samples were more influenced by blending ratios than by irradiation doses, showing that 3% and 5% added samples produced glow curves at 150 to 250 °C. After pasteurization of the samples containing the irradiated ingredient, TL glow intensity decreased but did not change its shape or temperature range. As a result, the pasteurization of Barbeque sauces containing irradiated ingredients had reduced TL glow intensity, but the shape and temperature range of glow curve were still able to provide information required for confirming irradiation treatment. To monitor the irradiated food in international market, thermoluminescence (TL) analysis is considered most promising identification technique because of its sensitivity and long-term stability. In this study the applicability of TL analysis to detect an irradiated ingredient (garlic powder) added in low quantity to a food matrix (sauce) was investigated. The effect of processing (pasteurization) on TL results was also evaluated. © 2012 Institute of Food Technologists®

Industrial yogurt manufacture: monitoring of fermentation process and improvement of final product quality.

PubMed

Soukoulis, C; Panagiotidis, P; Koureli, R; Tzia, C

2007-06-01

Lactic acid fermentation during the production of skim milk and whole fat set-style yogurt was continuously monitored by measuring pH. The modified Gompertz model was successfully applied to describe the pH decline and viscosity development during the fermentation process. The viscosity and incubation time data were also fitted to linear models against ln(pH). The investigation of the yogurt quality improvement practices included 2 different heat treatments (80 degrees C for 30 min and 95 degrees C for 10 min), 3 milk protein fortifying agents (skim milk powder, whey powder, and milk protein concentrate) added at 2.0%, and 4 hydrocolloids (kappa-carrageenan, xanthan, guar gum, and pectin) added at 0.01% to whole fat and skim yogurts. Heat treatment significantly affected viscosity and acetaldehyde development without influencing incubation time and acidity. The addition of whey powder shortened the incubation time but had a detrimental effect on consistency, firmness, and overall acceptance of yogurts. On the other hand, addition of skim milk powder improved the textural quality and decreased the vulnerability of yogurts to syneresis. Anionic stabilizers (kappa-carrageenan and pectin) had a poor effect on the texture and palatability of yogurts. However, neutral gums (xanthan and guar gum) improved texture and prevented the wheying-off defect. Skim milk yogurts exhibited longer incubation times and higher viscosities, whereas they were rated higher during sensory evaluation than whole fat yogurts.

The Effect of Premixed Al-Cu Powder on the Stir Zone in Friction Stir Welding of AA3003-H18

NASA Astrophysics Data System (ADS)

Abnar, B.; Kazeminezhad, M.; Kokabi, A. H.

2015-02-01

In this research, 3-mm-thick AA3003-H18 non-heat-treatable aluminum alloy plates were joined by friction stir welding (FSW). It was performed by adding pure Cu and premixed Cu-Al powders at various rotational speeds of 800, 1000, and 1200 rpm and constant traveling speeds of 100 mm/min. At first, the powder was filled into the gap (0.2 or 0.4 mm) between two aluminum alloy plates, and then the FSW process was performed in two passes. The microstructure, mechanical properties, and formation of intermetallic compounds were investigated in both cases of using pure Cu and premixed Al-Cu powders. The results of using pure Cu and premixed Al-Cu powders were compared in the stir zone at various rotational speeds. The copper particle distribution and formation of Al-Cu intermetallic compounds (Al2Cu and AlCu) in the stir zone were desirable using premixed Al-Cu powder into the gap. The hardness values were significantly increased by formation of Al-Cu intermetallic compounds in the stir zone and it was uniform throughout the stir zone when premixed Al-Cu powder was used. Also, longitudinal tensile strength from the stir zone was higher when premixed Al-Cu powder was used instead of pure Cu powder.

Enhancing the Thermotolerance of Entomopathogenic Isaria fumosorosea SFP-198 Conidial Powder by Controlling the Moisture Content Using Drying and Adjuvants

PubMed Central

Lee, Se Jin; Lee, Hyang Burm

2014-01-01

Entomopathogenic fungi are promising pest-control agents but their industrial applicability is limited by their thermosusceptibility. With an aim to increase the thermotolerance of Isaria fumosorosea SFP-198, moisture absorbents were added to dried conidial powder, and the relationship between its water potential and thermotolerance was investigated. Mycotized rice grains were dried at 10℃, 20℃, 30℃, and 40℃ and the drying effect of each temperature for 24, 48, 96, and 140 hr was determined. Drying for 48 hr at 10℃ and 20℃ reduced the moisture content to < 5% without any significant loss of conidial thermotolerance, but drying at 30℃ and 40℃ reduced both moisture content and conidial thermotolerance. To maintain thermotolerance during storage, moisture absorbents, such as calcium chloride, silica gel, magnesium sulfate, white carbon, and sodium sulfate were individually added to previously dried-conidial powder at 10% (w/w). These mixtures was then stored at room temperature for 30 days and subjected to 50℃ for 2 hr. The white carbon mixture had the highest conidial thermotolerance, followed by silica gel, magnesium sulfate, and then the other absorbents. A significant correlation between the water potential and conidial thermotolerance was observed in all conidia-absorbent mixtures tested in this study (r = -0.945). Conidial thermotolerance in wet conditions was evaluated by adding moisturized white carbon (0~20% H2O) to conidia to mimic wet conditions. Notably, the conidia still maintained their thermotolerance under these conditions. Thus, it is evident that conidial thermotolerance can be maintained by drying mycotized rice grains at low temperatures and adding a moisture absorbent, such as white carbon. PMID:24808736

The effect of precipitation and calcination parameters on oxalate derived ThO2 pellets

NASA Astrophysics Data System (ADS)

Wangle, Tadeas; Tyrpekl, Vaclav; Cagno, Simone; Delloye, Thierry; Larcher, Olivier; Cardinaels, Thomas; Vleugels, Jozef; Verwerft, Marc

2017-11-01

Thorium oxalate is easy to prepare, but the derived oxide powders retain the platelet morphology of the primary oxalate. This negatively impacts packing and sintering. If powder milling is to be avoided, powder synthesis needs to be optimized. That is the goal of this paper, where different precipitation strategies were used and their effect on powder characteristics and pellet synthesis was investigated. Oxalates prepared by adding a thorium nitrate solution to an oxalic acid solution proved most promising. Further optimizing of the calcination temperature revealed that with increasing calcination temperature the packing density improved significantly. This came at the cost of decreased early stage sintering and a higher frequency of end-capping during compaction. The calcination temperature at which the highest final density can be reached was dependent on the sintering cycle. Furthermore, the ThO2 powders had less surface area and thus adsorbed less gases during storage when calcined at higher temperatures.

The effect of kimchi on the microbiological stability of fermented sausage.

PubMed

Park, Young-Seo; Lee, Joo-Yeon

2012-12-01

The effects of kimchi and freeze-dried kimchi-powder added to raw meat mixtures on the microbiological quality of fermented sausage were studied. The results clearly demonstrated that the lactic acid bacteria (LAB) integrated via the addition of kimchi as well as kimchi-powder were well adapted to the new habitat of fermenting sausage, reaching maximum numbers of 8.65-8.80 log₁₀ cfu/g after 1-2 days of fermentation. In all kimchi and kimchi-powder sausages, the growth of Enterobacteriaceae was completely inhibited throughout the processing period (<2 log₁₀ cfu/g). The sausage batches containing more than 10% kimchi and 2% kimchi-powder showed no growth of S. aureus, whereas the control and another kimchi sausage batch reflected the growth of S. aureus (3.68-4.72 log₁₀ cfu/g). As a result, the addition of kimchi (≥10%) and kimchi-powder to the sausage mixture prior to fermentation produced the microbiological stability required for fermented sausages. Copyright © 2012 Elsevier Ltd. All rights reserved.

Facile synthesis of core-shell Cu2O@ ZnO structure with enhanced photocatalytic H2 production

NASA Astrophysics Data System (ADS)

Zhang, Yong-Hui; Jiu, Bei-Bei; Gong, Fei-Long; Lu, Kuan; Jiang, Nan; Zhang, Hao-Li; Chen, Jun-Li

2018-05-01

Core-shell Cu2O@ZnO composites were synthesized successfully based on a one-pot hydrothermal method in the presence of dioctyl sulfosuccinate sodium salt (AOT) surfactant. The Cu2O can be converted to rough core-shell Cu2O@ZnO structure by adjusting the amount of zinc powder added. The as-synthesized Cu2O@ZnO composites exhibited excellent photocatalytic activity and the amount of H2 generated using these composites was 4.5-fold more than that produced with Cu2O cubes. A possible photocatalytic mechanism for the Cu2O@ZnO composites with enhanced photocatalytic activity could be the separation by ZnO of the effective charge carriers.

Perspectives of Using Ultra-Fine Metals as Universal Safe BioStimulators to Get Cattle Breeding Quality Products

NASA Astrophysics Data System (ADS)

Polishchuk, S.

2015-11-01

We have conducted investigations of ultra-fine metals biological activity with lab non-pedigree white rats, rabbits breed “Soviet chinchilla” and cattle young stock of the black and white breed as the most widely spread in the central part of Russia. One can see the possibility of using microelements of ultra-fine iron, cobalt and copper as cheap, non-toxic and highly effective biological catalyst of biochemical processes in the organism that improve physiological state, morphological and biochemical blood parameters increasing activity of the experimental animals’ ferment systems and their productivity and meat biological value. We have proved the ultra-fine powders safety when adding them to the animals’ diet.

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karim, Ahmad Fikri Abdul, E-mail: a.fikri-89@yahoo.com; Ariff, Zulkifli Mohamad; Ismail, Hanafi

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed bymore » using scanning electron microscopy (SEM)« less

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1994-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1994-02-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (PCM) is provided. The silica particles have a critical size of about 0.005 to about 0.025 microns and the PCM must be added to the silica in an amount of 75% or less PCM per combined weight of silica and PCM. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a PCM material. The silica-PCM mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 2 figures.

Nutritional Composition of Australian Combat Ration Packs and Options for Improvement

DTIC Science & Technology

2013-10-01

cheese, scotch finger biscuit and sweetened condensed milk (Figure 9). High fat confectionery is the major contributor of vitamin A to CR1M menus...simultaneously assist in addressing the protein shortfall in all but one menu. 5.4.3 Dairy Skim milk powder is a minor component and not a major...The use of a moderate fat milk powder will also improve the stability of added vitamin A and should be considered as an alternative to the

Reduction Expansion Synthesis of Chromium and Nickel Metal Coatings

DTIC Science & Technology

2017-06-01

to a supersonic speed [24]–[25]. To prevent undesired combustion, an inert gas is required for because the gas temperature increases to 100–500°C in...take place. The metal is added by mechanical means only. In the sputtering process, an inert gas (e.g., argon) is supplied to a vacuum chamber with...technique that uses metal powder and compressed gas to feed the powder to a converging-diverging nozzle [24], as shown in Figure 5. The converging

Inhibiting excessive acidification using zero-valent iron in anaerobic digestion of food waste at high organic load rates.

PubMed

Kong, Xin; Wei, Yonghong; Xu, Shuang; Liu, Jianguo; Li, Huan; Liu, Yili; Yu, Shuyao

2016-07-01

Excessive acidification occurs frequently in food waste (FW) anaerobic digestion (AD) due to the high carbon-to-nitrogen ratio of FW. In this study, zero-valent iron (ZVI) was applied to prevent the excessive acidification. All of the control groups, without ZVI addition (pH∼5.3), produced little methane (CH4) and had high volatile fatty acids/bicarbonate alkalinity (VFA/ALK). By contrast, at OLR of 42.32gVS/Lreactor, the pH of effluent from the reactors with 0.4g/gVSFWadded of ZVI increased to 7.8-8.2, VFA/ALK decreased to <0.1, and the final CH4 yield was ∼380mL/gVSFWadded, suggesting inhibition of excessive acidification. After adding powdered or scrap metal ZVI to the acidogenic reactors, the fractional content of butyric acid changed from 30-40% to 0%, while, that of acetic acid increased. These results indicate that adding ZVI to FW digestion at high OLRs could eliminate excessive acidification by promoting butyric acid conversion and enhancing methanogen activity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Composite carbon foam electrode

DOEpatents

Mayer, Steven T.; Pekala, Richard W.; Kaschmitter, James L.

1997-01-01

Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivty and power to system energy.

Retention of antioxidant capacity of vacuum microwave dried cranberry.

PubMed

Leusink, Gwen J; Kitts, David D; Yaghmaee, Parastoo; Durance, Tim

2010-04-01

In this study, cranberries were dried by vacuum-microwave drying (VMD), freeze-drying (FD), or hot air-drying (AD), to compare the effects of different drying processes on both physical changes as well as the retention of bioactive components in dried samples. Total porosity (%) and average pore radius of dehydrated cranberries were greater using VMD compared to FD and AD (P < 0.05). Crude methanol cranberry powdered extracts were fractionated by solid phase extraction (SPE) into organic acid-, total phenolics-, anthocyanin-, or proanthocyanidin-enriched extracts, respectively. The chemical composition of the 60% acidified methanol fractions contained cyanidin-3-galactoside, cyanidin-3-arabinoside, peonidin-3-galactoside, and peonidin-3-arabinoside, as assessed by HPLC. Antioxidant activities of cranberry fractions were measured using chemical ORAC and ABTS methods. The 60% acidified methanol fraction had a significantly higher (P < 0.05) antioxidant potential than the other chemical fractions, which was largely attributed to the relatively higher anthocyanin content. In general, vacuum-microwave drying and freeze-drying resulted in similar retention of anthocyanins and antioxidant activity, which were both relatively higher (P < 0.05) than that recovered from cranberries dried by hot air drying.

Method for low temperature preparation of a noble metal alloy

DOEpatents

Even, Jr., William R.

2002-01-01

A method for producing fine, essentially contamination free, noble metal alloys is disclosed. The alloys comprise particles in a size range of 5 to 500 nm. The method comprises 1. A method for preparing a noble metal alloy at low temperature, the method comprising the steps of forming solution of organometallic compounds by dissolving the compounds into a quantity of a compatible solvent medium capable of solvating the organometallic, mixing a portion of each solution to provide a desired molarity ratio of ions in the mixed solution, adding a support material, rapidly quenching droplets of the mixed solution to initiate a solute-solvent phase separation as the solvent freezes, removing said liquid cryogen, collecting and freezing drying the frozen droplets to produce a dry powder, and finally reducing the powder to a metal by flowing dry hydrogen over the powder while warming the powder to a temperature of about 150.degree. C.

The Effect of Cu Powder During Friction Stir Welding on Microstructure and Mechanical Properties of AA3003-H18

NASA Astrophysics Data System (ADS)

Abnar, B.; Kazeminezhad, M.; Kokabi, A. H.

2014-08-01

Friction stir welding (FSW) was used to join 3003-H18 non-heat-treatable aluminum alloy plates by adding copper powder. The copper powder was first added to the gap (0.1 and 0.2 mm) between two plates and then the FSW was performed. The specimens were joined at various rotational speeds of 800, 1000, and 1200 rpm at traveling speeds of 70 and 100 mm/min. The effects of rotational speed, second pass of FSW, and direction of second pass also were studied on copper particle distribution and formation of Al-Cu intermetallic compounds in the stir zone. The second pass of FSW was carried out in two ways; in line with the first pass direction (2F) and in the reverse direction of the first pass (FB). The microstructure, mechanical properties, and formation of intermetallic compounds type were investigated. In high copper powder compaction into the gap, large clusters were formed in the stir zone, while fine clusters and sound copper particles distribution were obtained in low powder compaction. The copper particle distribution and amount of Al-Cu intermetallic compounds were increased in the stir zone with increasing the rotational speed and applying the second pass. Al2Cu and AlCu intermetallic phases were formed in the stir zone and consequently the hardness was significantly increased. The copper particles and in situ intermetallic compounds were symmetrically distributed in both advancing and retreating sides of weld zone after FB passes. Thus, the wider area was reinforced by the intermetallic compounds. Also, the tensile test specimens tend to fracture from the coarse copper aggregation at the low rotational speeds. At high rotational speeds, the fracture locations are placed in HAZ and TMAZ.

Physicochemical and Antioxidant Activities of Spray-dried Pitaya Fruit Powder

NASA Astrophysics Data System (ADS)

Li, Guopeng; Liu, Yangyang; Lin, Lijing; Li, Jihua

2018-01-01

Pitaya commonly known as dragon fruit is very popular in China due to its intense color, constituent minerals, vitamins, and antioxidant properties. In the present study, physiochemical properties and antioxidant activities of fruit powder from two pitaya cultivars (namely red flesh and white flesh) and fruit peel were observed. Compared with the fruit powder of fruit flesh, the fruit powder made from fruit peel showed a higher antioxidant activity. The current study provides insights to produce spray-dried pitaya fruit powders that could potentially be used as functional food ingredients in various food fields.

Particle morphology influence on mechanical and biocompatibility properties of injection molded Ti alloy powder.

PubMed

Gülsoy, H Özkan; Gülsoy, Nagihan; Calışıcı, Rahmi

2014-01-01

Titanium and Titanium alloys exhibits properties that are excellent for various bio-applications. Metal injection molding is a processing route that offers reduction in costs, with the added advantage of near net-shape components. Different physical properties of Titanium alloy powders, shaped and processed via injection molding can achieve high complexity of part geometry with mechanical and bioactivity properties, similar or superior to wrought material. This study describes that the effect of particle morphology on the microstructural, mechanical and biocompatibility properties of injection molded Ti-6Al-4V (Ti64) alloy powder for biomaterials applications. Ti64 powders irregular and spherical in shape were injection molded with wax based binder. Binder debinding was performed in solvent and thermal method. After debinding the samples were sintered under high vacuum. Metallographic studies were determined to densification and the corresponding microstructural changes. Sintered samples were immersed in a simulated body fluid (SBF) with elemental concentrations that were comparable to those of human blood plasma for a total period of 15 days. Both materials were implanted in fibroblast culture for biocompatibility evaluations were carried out. The results show that spherical and irregular powder could be sintered to a maximum theoretical density. Maximum tensile strength was obtained for spherical shape powder sintered. The tensile strength of the irregular shape powder sintered at the same temperature was lower due to higher porosity. Finally, mechanical tests show that the irregular shape powder has lower mechanical properties than spherical shape powder. The sintered irregular Ti64 powder exhibited better biocompatibility than sintered spherical Ti64 powder. Results of study showed that sintered spherical and irregular Ti64 powders exhibited high mechanical properties and good biocompatibility properties.

Polymeric additives to enhance the functional properties of calcium phosphate cements

PubMed Central

Perez, Roman A; Kim, Hae-Won

2012-01-01

The vast majority of materials used in bone tissue engineering and regenerative medicine are based on calcium phosphates due to their similarity with the mineral phase of natural bone. Among them, calcium phosphate cements, which are composed of a powder and a liquid that are mixed to obtain a moldable paste, are widely used. These calcium phosphate cement pastes can be injected using minimally invasive surgery and adapt to the shape of the defect, resulting in an entangled network of calcium phosphate crystals. Adding an organic phase to the calcium phosphate cement formulation is a very powerful strategy to enhance some of the properties of these materials. Adding some water-soluble biocompatible polymers in the calcium phosphate cement liquid or powder phase improves physicochemical and mechanical properties, such as injectability, cohesion, and toughness. Moreover, adding specific polymers can enhance the biological response and the resorption rate of the material. The goal of this study is to overview the most relevant advances in this field, focusing on the different types of polymers that have been used to enhance specific calcium phosphate cement properties. PMID:22511991

Engineered particles demonstrate improved flow properties at elevated drug loadings for direct compression manufacturing.

PubMed

Trementozzi, Andrea N; Leung, Cheuk-Yui; Osei-Yeboah, Frederick; Irdam, Erwin; Lin, Yiqing; MacPhee, J Michael; Boulas, Pierre; Karki, Shyam B; Zawaneh, Peter N

2017-05-15

Optimizing powder flow and compaction properties are critical for ensuring a robust tablet manufacturing process. The impact of flow and compaction properties of the active pharmaceutical ingredient (API) becomes progressively significant for higher drug load formulations, and for scaling up manufacturing processes. This study demonstrated that flow properties of a powder blend can be improved through API particle engineering, without critically impacting blend tabletability at elevated drug loadings. In studying a jet milled API (D 50 =24μm) and particle engineered wet milled API (D 50 =70μm and 90μm), flow functions of all API lots were similarly poor despite the vast difference in average particle size (ff c <4). This finding strays from the common notion that powder flow properties are directly correlated to particle size distribution. Upon adding excipients, however, clear trends in flow functions based on API particle size were observed. Wet milled API blends had a much improved flow function (ff c >10) compared with the jet milled API blends. Investigation of the compaction properties of both wet and jet milled powder blends also revealed that both jet and wet milled material produced robust tablets at the drug loadings used. The ability to practically demonstrate this uncommon observation that similarly poor flowing APIs can lead to a marked difference upon blending is important for pharmaceutical development. It is especially important in early phase development during API selection, and is advantageous particularly when material-sparing techniques are utilized. Copyright © 2017 Elsevier B.V. All rights reserved.

Production of coconut protein powder from coconut wet processing waste and its characterization.

PubMed

Naik, Aduja; Raghavendra, S N; Raghavarao, K S M S

2012-07-01

Virgin coconut oil (VCO) has been gaining popularity in recent times. During its production, byproducts such as coconut skim milk and insoluble protein are obtained which are underutilized or thrown away to the environment at present. This study deals with utilization of these byproducts to obtain a value-added product, namely, coconut protein powder. When coconut milk was subjected to centrifugation, three phases, namely, fat phase (coconut cream), aqueous phase (coconut skim milk), and solid phase (insoluble protein) were obtained. The coconut skim milk and insoluble protein were mixed and homogenized before spray drying to obtain a dehydrated protein powder. The proximate analysis of the powder showed high protein content (33 % w/w) and low fat content (3 % w/w). Protein solubility was studied as a function of pH and ionic content of solvent. Functional properties such as water hydration capacity, fat absorption capacity, emulsifying properties, wettability, and dispersibility of coconut protein powder were evaluated along with morphological characterization, polyphenol content, and color analysis. Coconut protein powder has shown to have good emulsifying properties and hence has potential to find applications in emulsified foods. Sensory analysis showed high overall quality of the product, indicating that coconut protein powder could be a useful food ingredient.

Research on microstructure properties of the TiC/Ni-Fe-Al coating prepared by laser cladding technology

NASA Astrophysics Data System (ADS)

Jiao, Junke; Xu, Zifa; Zan, Shaoping; Zhang, Wenwu; Sheng, Liyuan

2017-10-01

In this paper, the laser cladding method was used to preparation the TiC reinforced Ni-Fe-Al coating on the Ni base superalloy. The Ti/Ni-Fe-Al powder was preset on the Ni base superalloy and the powder layer thickness is 0.5mm. A fiber laser was used the melting Ti/Ni-Fe-Al powder in an inert gas environment. The shape of the cladding layer was tested using laser scanning confocal microscope (LSCM) under different cladding parameters such as the laser power, the melting velocity and the defocused amount. The microstructure, the micro-hardness was tested by LSCM, SEM, Vickers hardness tester. The test result showed that the TiC particles was distributed uniformly in the cladding layer and hardness of the cladding layer was improved from 180HV to 320HV compared with the Ni-Fe-Al cladding layer without TiC powder reinforced, and a metallurgical bonding was produced between the cladding layer and the base metal. The TiC powder could make the Ni-Fe-Al cladding layer grain refining, and the more TiC powder added in the Ni-Fe-Al powder, the smaller grain size was in the cladding layer.

Latex Allergy: A Prevention Guide

MedlinePlus

... most common reaction to latex products is irritant contact dermatitis – the development of dry, itchy, irritated areas on ... exposure to the powders added to them. Irritant contact dermatitis is not a true allergy. Allergic contact dermatitis ( ...

Zesty Tomato Soup

MedlinePlus

... added diced tomatoes 1 cup jarred roasted red peppers, drained (or substitute fresh roasted red peppers) 1 cup fat-free evaporated milk 1 tsp garlic powder 1/4 tsp ground black pepper 2 Tbsp fresh basil, rinsed and chopped (or ...

Spheroidization of silica powders by radio frequency inductively coupled plasma with Ar-H2 and Ar-N2 as the sheath gases at atmospheric pressure

NASA Astrophysics Data System (ADS)

Li, Lin; Ni, Guo-hua; Guo, Qi-jia; Lin, Qi-fu; Zhao, Peng; Cheng, Jun-li

2017-09-01

Amorphous spherical silica powders were prepared by inductively coupled thermal plasma treatment at a radio frequency of 36.2 MHz. The effects of the added content of hydrogen and nitrogen into argon (serving as the sheath gas), as well as the carrier gas flow rate, on the spheroidization rate of silica powders, were investigated. The prepared silica powders before and after plasma treatment were examined by scanning electron microscopy, X-ray diffraction, and laser granulometric analysis. Results indicated that the average size of the silica particles increased, and the transformation of crystals into the amorphous state occurred after plasma treatment. Discharge image processing was employed to analyze the effect of the plasma temperature field on the spheroidization rate. The spheroidization rate of the silica powder increased with the increase of the hydrogen content in the sheath gas. On the other hand, the spheroidization rate of the silica power first increased and then decreased with the increase of the nitrogen content in the sheath gas. Moreover, the amorphous content increased with the increase of the spheroidization rate of the silica powder.

Detecting Corrosion Resistance of Coated Steel Rebars by Electrochemical Technique (eis)

NASA Astrophysics Data System (ADS)

Ryou, J.; Shah, S.

Electrochemical impedance spectroscopy (EIS) is one of the electrochemical techniques used in materials science. The present measurements are used to evaluate the corrosion resistance of new types of coated steel rebar used in reinforced concrete. In this study, Si-based coating materials are used and evaluated, because adding Si to metals and alloys, including steel, generally increases their corrosion, oxidation, and erosion resistance. The result suggests that electrochemical impedance spectroscopy may be useful for monitoring corrosion activity on coated steel rebars. Based upon impedance changes, it appears that the silicon powder coating bonds well to the steel, and that the coating has a good performance.

Carbonate addition--an effective remedy against poor activated sludge settling properties and alkalinity conditions in small wastewater treatment plants.

PubMed

Wett, B; Eladawy, A; Becker, W

2003-01-01

The impact of marble powder on the performance of small seasonal treatment plants dealing with high ammonia concentrated wastewater has been investigated. The carbonate has been added to one of two parallel lab-scale SBR-systems as an alkalinity depot and a bio-carrier. The focus of the monitoring program was put on the measurement of carbon fractions in the liquid and the solid phase and on the alkalinity conditions. Monitoring results show a significant correlation between carbonate dosage (and corresponding inorganic carbon concentration and pH-value) and sludge volume index and nitrification rate.

Preparation and characterization of adefovir dipivoxil-stearic acid cocrystal with enhanced physicochemical properties.

PubMed

Seo, Jeong-Woong; Hwang, Kyu-Min; Lee, Sung-Hoon; Kim, Dong-Wook; Park, Eun-Seok

2017-06-11

The objectives of this study were to prepare cocrystal composed of adefovir dipivoxil (AD) and stearic acid (SA) and to investigate the enhanced properties of the cocrystal. The cocrystal was prepared by antisolvent precipitation and characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRPD), and differential scanning calorimetry (DSC). The enhanced properties were evaluated by dissolution testing, permeability studies, and powder rheology analysis. The AD raw material has a cuboid-like crystal and the cocrystal has a needle shape. In the FT-IR study, there were bathochromic shifts caused by the hydrogen bonding. The melting point of the cocrystal was 52.9 °C, which was lower than that of AD. The XRPD pattern also had distinct differences, supporting the formation of a new crystalline form. The cocrystal showed changes in the lattice energy and the solvation strength, which caused an enhanced dissolution. The permeability was increased due to the SA, which acts as a P-gp inhibitor. The tabletability was enhanced due to the altered crystal habit. In conclusion, cocrystal containing AD and SA was successfully prepared, presenting advantages such as enhanced solubility, tabletability, and permeability. The use of the cocrystal is a desirable approach for the improved physicochemical properties.

Effect of the Addition of Schisandra chinensis Powder on the Physico-chemical Characteristics of Sausage

PubMed Central

Jin, S. K.; Park, J. H.

2013-01-01

The individual and interactive effects of Schisandra chinensis powder (SCP) and sodium nitrite additions on color, pH, water holding capacity, residual nitrite, 2-thiobarbituric acid reactive substances (TBARS), volatile basic nitrogen, texture properties, fatty acids, amino acids and sensory evaluation of cooked pork sausages were investigated after 20 d of storage at 4°C. The powders (0, 0.5 and 1.0%) were added to sausages either alone or in combination with nitrite (0 and 100 ppm). SCP added-sausages showed lower L* (lightness) and W (whiteness) values, and higher b* (yellowness) values than sausage containing no nitrite, and exhibited the highest a* values at a 0.5% addition (p<0.05). Residual nitrite and TBARS values were found to be significantly reduced as the addition levels of SCP increased (p<0.05). As the addition of SCP increased, the sausage showed gradually decreased brittleness, cohesiveness, springiness, gumminess and chewiness, while adhesiveness increased. Polyunsaturated fatty acid, n-6 and n-6/n-3 fatty acid ratio concentrations were significantly higher in sausages containing SCP (p<0.05). The addition of SCP to sausage significantly (p<0.05) increased the ammonia content (by 0.5% SCP) and aromatic amino acid concentrations (by 1.0% SCP) (p<0.05). Inclusion of SCP in sausage meat resulted in a significant deterioration in quality characteristics of flavor, springiness, juiciness and overall acceptability (p<0.05). As expected, the observed changes in a*, W, pH, shear force, texture property, TBARS, fatty acid, amino acid and sensory score of sausages, depended on the rate of addition of nitrite (p<0.05). These results suggest that SCP addition is not an effective way of improving the sensory evaluation of sausages, but may beneficially affect TBARS, nitrite scavenging activity, fatty acid and amino acid content in pork sausages. PMID:25049766

Enhanced Magnetic Properties of Nd15Fe77B8 Alloy Powders Produced by Melt-Spinning Technique

NASA Astrophysics Data System (ADS)

Öztürk, Sultan; İcin, Kürşat; Öztürk, Bülent; Topal, Uğur; Odabaşı, Hülya Kaftelen; Göbülük, Metin; Cora, Ömer Necati

2017-10-01

Rapidly solidified Nd15Fe77B8 alloy powders were produced by means of melt-spinning method in high-vacuum atmosphere to achieve improved magnetic and thermal properties. To this goal, a vacuum milling apparatus was designed and constructed to ball-mill the melt-spun powders in a surfactant active atmosphere. Various milling times were experimented to reveal the effect of the milling time on the mean particle size and other size-dependent properties such as magnetism and Curie temperature. Grain structure, cooling rate, and phase structure of the produced powders were also investigated. The Curie points shifted to higher temperatures from the ingot condition to surfactant active ball-milling and the values for Nd15Fe77B8 ingot alloy, melt-spun powders, and surfactant active ball-milled powders were 552 K, 595 K, and 604 K (279 °C, 322 °C, and 331 °C), respectively. It was noted that the surfactant active ball-milling process improved the magnetic and thermal properties of melt-spun Nd15Fe77B8 alloy powders. Compared to relevant literature, the coercivity of powders increased significantly with increasing milling time and decreasing in powder size. The coercivity value as high as 3427 kA m-1 was obtained.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1992-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1993-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Influence of metallic additives on manganese ferrites sintering

NASA Astrophysics Data System (ADS)

Shevelev, S. A.; Luchnikov, P. A.; Yarullina, A. R.

2018-01-01

Influence of cuprum nanopowder additive received by electric explosion on the process of manganese ferrites MgFe2O4 consolidating at thermal sintering was researched by dilatometry method. Cuprum nanopowder at a rate of 5 mass % was added into the original commercial-grade powder of manganese ferrite MgFe2O4. Powder mixture was numerously blended with screening for better blending before pressing. Powder compacts were formed by cold one-axle static pressing. It was proved that introduction of cuprum additive caused shrinkage increase at final heating stage. There was abnormal compact enlarging at sintering in the air at isothermal stage; the specified process was not observed in vacuum. This difference can be explained by changes in conditions of gaseous discharge from volume of pores.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, Ival O.

1993-01-01

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7.times.10.sup.-3 to about 7.times.10.sup.-2 microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garmets, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Graft polymerization of acrylic acid and methacrylic acid onto poly(vinylidene fluoride) powder in presence of metallic salt and sulfuric acid

NASA Astrophysics Data System (ADS)

Deng, Bo; Yu, Yang; Zhang, Bowu; Yang, Xuanxuan; Li, Linfan; Yu, Ming; Li, Jingye

2011-02-01

Poly(vinylidene fluoride) (PVDF) powder was grafted with acrylic acid (AAc) or methacrylic acid (MAA) by the pre-irradiation induced graft polymerization technique. The presence of graft chains was proven by FT-IR spectroscopy. The degree of grafting (DG) was calculated by the acid-base back titration method. The synergistic effect of acid and Mohr's salt on the grafting kinetics was examined. The results indicated that adding sulfuric acid and Mohr's salt simultaneously in AAc or MAA solutions led to a strong enhancement in the degree of grafting. The grafted PVDF powder was cast into microfiltration (MF) membranes using the phase inversion method and some properties of the obtained MF membranes were characterized.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1993-10-19

Free flowing, conformable powder-like mix of silica particles and a phase change material (pcm) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 10 figures.

Screenable contact structure and method for semiconductor devices

DOEpatents

Ross, Bernd

1980-08-26

An ink composition for deposition upon the surface of a semiconductor device to provide a contact area for connection to external circuitry is disclosed, the composition comprising an ink system containing a metal powder, a binder and vehicle, and a metal frit. The ink is screened onto the semiconductor surface in the desired pattern and is heated to a temperature sufficient to cause the metal frit to become liquid. The metal frit dissolves some of the metal powder and densifies the structure by transporting the dissolved metal powder in a liquid sintering process. The sintering process typically may be carried out in any type of atmosphere. A small amount of dopant or semiconductor material may be added to the ink systems to achieve particular results if desired.

Capacitor with a composite carbon foam electrode

DOEpatents

Mayer, Steven T.; Pekala, Richard W.; Kaschmitter, James L.

1999-01-01

Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid partides being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy.

Method for fabricating composite carbon foam

DOEpatents

Mayer, Steven T.; Pekala, Richard W.; Kaschmitter, James L.

2001-01-01

Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy.

Capacitor with a composite carbon foam electrode

DOEpatents

Mayer, S.T.; Pekala, R.W.; Kaschmitter, J.L.

1999-04-27

Carbon aerogels used as a binder for granularized materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy. 1 fig.

Composite carbon foam electrode

DOEpatents

Mayer, S.T.; Pekala, R.W.; Kaschmitter, J.L.

1997-05-06

Carbon aerogels used as a binder for granulated materials, including other forms of carbon and metal additives, are cast onto carbon or metal fiber substrates to form composite carbon thin film sheets. The thin film sheets are utilized in electrochemical energy storage applications, such as electrochemical double layer capacitors (aerocapacitors), lithium based battery insertion electrodes, fuel cell electrodes, and electrocapacitive deionization electrodes. The composite carbon foam may be formed by prior known processes, but with the solid particles being added during the liquid phase of the process, i.e. prior to gelation. The other forms of carbon may include carbon microspheres, carbon powder, carbon aerogel powder or particles, graphite carbons. Metal and/or carbon fibers may be added for increased conductivity. The choice of materials and fibers will depend on the electrolyte used and the relative trade off of system resistivity and power to system energy. 1 fig.

Microstructure and Properties of Zircon-Added Carbon Refractories for Blast Furnace

NASA Astrophysics Data System (ADS)

Zhu, Tianbin; Li, Yawei; Sang, Shaobai; Chen, Xilai; Zhao, Lei; Li, Yuanbing; Li, Shujing

2012-11-01

Microstructure and properties of zircon-added carbon refractory specimens for blast furnace (BF) were investigated with the aid of X-ray diffraction (XRD), a scanning electron microscope (SEM), energy-dispersive X-ray, mercury porosimetry, and a laser thermal conductivity (TC) meter. Additives could influence the matrix structures and improve the properties of specimens. With the increase of zircon powder content, the amount of SiC whiskers formed increased and their aspect ratio became larger, and the SiC whiskers tended to be distributed homogeneously. Zircon powder additions decreased the mean pore diameter and increased <1- μm pore volume by filling in pores via SiC, improved the TC and the cold crushing strength (CCS) due to the in-situ formation of the more well-developed SiC whiskers with high TC, and significantly reduced the molten iron attack to carbon specimens.

Influence of full cream milk powder on the characteristics of sweet potato puree instant cream soup

NASA Astrophysics Data System (ADS)

Sunyoto, Marleen; Djali, Mohamad; Dwiastuti, Intan Btari

2018-02-01

A ready to use food such as instant cream soup become the most suitable choice for those who prefer being practical and also can be applied in any emergency situation such as areas affected by disaster. The adding of milk powder as the main ingredient in cream soup creates a complex bounding of fat and starch which complicates the rehydration process and affects other physical appearance. This research was aimed to find the proper concentration of full cream milk powder concentration to obtain the best characteristics of instant cream soup of dried sweet potato puree. The method used in this research was randomized block design with 6 treatments (12.5%, 15%, 17.5%, 20%, 22.5% and 25%, with an addition of full cream milk powder) and twice repetition. Instant cream soup with 20% of full cream milk powder concentration gave the best physical and chemical characteristics. The physical and chemical characteristic shows that it has 6% water content, 95.47% rehydration value, 18% protein, 20.7% fat, 1080.25 cP viscosity and 30.5% rendement.

Valorization of functional properties of extract and powder of olive leaves in raw and cooked minced beef meat.

PubMed

Aouidi, Fathia; Okba, Aicha; Hamdi, Moktar

2017-08-01

Olive leaves (OL), available in huge amounts from pruning, are known to be a useful source of biologically active compounds. This study investigated the potential application of OL as a supplement to minced beef meat in order to develop a functional product. The effect of OL extract or powder (100 and 150 µg phenols g -1 meat) on the quality and stability of raw and cooked meat during refrigerated storage was examined. Microwave drying at 600 W gave OL with the highest antioxidant quality (evaluated by TEAC/[phenols] (mg mg -1 ) and DPPH/[phenols] (mg mg -1 )) compared with other methods. OL showed an ability to inhibit (P < 0.05) lipid oxidation (TBARS values (mg MDA kg -1 ) were reduced by 25-65%) and myoglobin oxidation (metmyoglobin production was 43-65% in control samples and 14-35% in treated samples). OL also improved the technological quality of the meat, decreasing (P < 0.05) storage loss (%) and defrosting loss (%) without affecting cooking loss (%) and Napole yield (%). Sensory properties were not modified by the added ingredient at the tested levels (P < 0.05). OL (extract or powder) may have applications in the development of functional meat products of good technological quality that remain stable during storage. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Performance Using Bamboo Fiber Ash Concrete as Admixture Adding Superplasticizer

NASA Astrophysics Data System (ADS)

Vasudevan, Gunalaan

2017-06-01

The increasing demand on natural resources for housing provisions in developing countries have called for sourcing and use of sustainable local materials for building and housing delivery. Natural materials to be considered sustainable for building construction should be ‘green’ and obtained from local sources, including rapidly renewable plant materials like palm fronds and bamboo, recycled materials and other products that are reusable and renewable. Each year, tens of millions of tons of bamboo are utilized commercially, generating a vast amount of waste. Besides that, bamboo fiber is easy availability, low density, low production cost and satisfactory mechanical properties. One solution is to activate this waste by using it as an additive admixture in concrete to keep it out of landfills and save money on waste disposal. The research investigates the mechanical and physical properties of bamboo fiber powder in a blended Portland cement. The structural value of the bamboo fiber powder in a blended Portland cement was evaluated with consideration for its suitability in concrete. Varied percentage of bamboo fiber powder (BFP) at 0%, 5%, 10%, 15%, and 20% as an admixture in 1:2:4 concrete mixes. The workability of the mix was determined through slump; standard consistency test was carried on the cement. Compressive strength of hardened cured (150 x 150 x 150) mm concrete cubes at 7days, 14days and 28days were tested.

Marigold flower-powder exhibits significant potential to inhibit lipid oxidation in rice bran tea.

PubMed

Wanyo, Pitchaporn; Kaewseejan, Niwat; Meeso, Naret; Siriamornpun, Sirithon

2015-06-01

We supplemented marigold flower-powder (MFP) in rice bran tea at different proportions as a source of natural antioxidant compounds. Changes of phenolic compounds, antioxidant activity, fatty acid composition and lipid oxidation in the rice bran tea with MFP after 30 days of storage were investigated, comparing results with the initial data. Adding MFP in rice bran tea resulted in an increased content and composition of phenolics and flavonoids along with enhanced antioxidant activities, which were increased in a dose-dependent manner. As a result, MFP supplementation of rice bran tea was able to retard the lipid oxidation as determined by the peroxide value (PV), due to the protection of essential fatty acids during 30 days of storage. The PVs were strongly negatively correlated (p < 0.01) with phenolic compounds, total phenolic content (TPC) and total flavonoid content (TFC), but were positively correlated with tocopherols and γ-oryzanol contents. We also found that the PV was positively correlated with the PUFA (poly unsaturated fatty acid) content but adverse results were found for SFA (saturated fatty acid) and MUFA (mono unsaturated fatty acid) contents. These findings suggest that MFP could be used as a natural antioxidant in foods for preventing lipid oxidation as well as extending the shelf-life of food products.

Bronchiolitis obliterans organizing pneumonia due to titanium nanoparticles in paint.

PubMed

Cheng, Tong-Hong; Ko, Fu-Chang; Chang, Junn-Liang; Wu, Kuo-An

2012-02-01

We present a case of a 58-year-old man who experienced Bronchiolitis obliterans organizing pneumonia after a 3-month exposure to polyester powder paint. Mineralogical analysis by transmission electron microscopy of a pulmonary sample and the polyester powder paint he was exposed to showed the presence of titanium dioxide nanoparticles in both. We suggest that exposure to titanium dioxide nanoparticles should be added to the etiology of Bronchiolitis obliterans organizing pneumonia. Copyright © 2012 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

ECCENTRIC ROLLING OF POWDER AND BONDING AGENT INTO SPHERICAL PELLETS

DOEpatents

Patton, G. Jr.; Zirinsky, S.

1961-06-01

A machine is described for pelletizing powder and bonding agent into spherical pellets of high density and uniform size. In this device, the material to be compacted is added to a flat circular pan which is moved in a circular orbit in a horizontal plane about an axis displaced from that of the pan's central axis without rotating the pan about its central axis. This movement causes the material contained therein to roll around the outside wall of the container and build up pellets of uniform shape, size, and density.

A Fundamental Study of Tool Steels Processed from Rapidly Solidified Powders.

DTIC Science & Technology

1981-12-01

structures, HIP or HIP and hot-worked high speed tool steels and powder forgings of low and medium alloy steels for load- bearing automotive...M7, M7S, M41, M42, M43S, T15 and M50 . These P/M tool steels exhibit a degree of alloy homogeneity and a fineness/uniformity of carbide dispersion...AD-AIl2 758 DREXEL UNIV PHILADEL.PH IA PA DEPT OF MATERIALS ENGINEERING F/6 11/6 A FUNDAMENTAL STUDY OF TOOL STEELS PROCESSED FROM L DEC 81 A

Chemical plating method of preparing radiation source material

DOEpatents

Smith, P.K.; Huntoon, R.T.; Mosley, W.C. Jr.

1973-12-11

A uniform dispersion of a radioisotope within a noble metal matrix is provided by chemically plating a noble metal coating onto particles including a dissociable compound of the mdioisotope. A suspension of the dissociable compound in a chemically reductive solution is prepared and noble metal cations added to produce the noble metal coatings. The coated particles are filtered, dried and heated to calcine the dissociable compound to a refractory powder. The powder can be encapsulated in measured portions or consolidated and shaped into an elongated form for easy apportionnnent as radiation source material. (Official Gazette)

Preparation of tungsten oxide

DOEpatents

Bulian, Christopher J [Yankton, SD; Dye, Robert C [Los Alamos, NM; Son, Steven F [Los Alamos, NM; Jorgensen, Betty S [Jemez Springs, NM; Perry, W Lee [Jemez Springs, NM

2009-09-22

Tungsten trioxide hydrate (WO.sub.3.H.sub.2O) was prepared from a precursor solution of ammonium paratungstate in concentrated aqueous hydrochloric acid. The precursor solution was rapidly added to water, resulting in the crash precipitation of a yellow white powder identified as WO.sub.3.H.sub.2O nanosized platelets by x-ray diffraction and scanning electron microscopy. Annealing of the powder at 200.degree. C. provided cubic phase WO.sub.3 nanopowder, and at 400.degree. C. provided WO.sub.3 nanopowder as a mixture of monoclinic and orthorhombic phases.

Fabrication of transparent ceramics using nanoparticles

DOEpatents

Cherepy, Nerine J; Tillotson, Thomas M; Kuntz, Joshua D; Payne, Stephen A

2012-09-18

A method of fabrication of a transparent ceramic using nanoparticles synthesized via organic acid complexation-combustion includes providing metal salts, dissolving said metal salts to produce an aqueous salt solution, adding an organic chelating agent to produce a complexed-metal sol, heating said complexed-metal sol to produce a gel, drying said gel to produce a powder, combusting said powder to produce nano-particles, calcining said nano-particles to produce oxide nano-particles, forming said oxide nano-particles into a green body, and sintering said green body to produce the transparent ceramic.

Gelcasting methods

DOEpatents

Walls, Claudia A.; Kirby, Glen H.; Janney, Mark A.; Omatete, Ogbemi O.; Nunn, Stephen D.; McMillan, April D.

2000-01-01

A method of gelcasting includes the steps of providing a solution of at least hydroxymethylacrylamide (HMAM) and water. At least one inorganic powder is added to the mixture. At least one initiator system is provided to polymerize the HMAM. The initiator polymerizes the HMAM and water, to form a firm hydrogel that contains the inorganic powder. One or more comonomers can be polymerized with the HMAM monomer, to alter the final properties of the gelcast material. Additionally, one or more additives can be included in the polymerization mixture, to alter the properties of the gelcast material.

Get Cooking with Chemistry!

ERIC Educational Resources Information Center

American Chemical Society, Washington, DC.

This book presents science activities investigating the chemical changes and reactions with powders that are used in baking. Activities include: (1) Mystery Powders; (2) Find the Fizz: Discover the Secret of Baking Powder; and (3) A Feast for Yeast and Cheese: Behold the Power of Chemistry. (YDS)

Low cost synthesis of TiO2-C nanocomposite powder for high efficiency visible light photocatalysis

NASA Astrophysics Data System (ADS)

Mohapatra, A. K.; Nayak, J.

2018-04-01

Titanium dioxide-carbon nanocomposite powder was synthesized via a low cost chemical route using oleic acid and titanium tetra-isopropoxide. Since the carbon remained mainly on the surface of the TiO2 nanoparticles, the powder had black color. The composition of the powder was analyzed by X-ray photoelectron spectroscopy and the structure was studied with X-ray diffraction and transmission electron microscopy. The visible photocatalytic activity of the black TiO2 powder was investigated by studying the photo-bleaching of methylene blue under visible light. Our experimental observation showed that the black-TiO2 powder had a higher visible photocatalytic activity compared to the commercial TiO2 powder (P25 Degussa).

Application of sodium carbonate prevents sulphur poisoning of catalysts in automated total mercury analysis

NASA Astrophysics Data System (ADS)

McLagan, David S.; Huang, Haiyong; Lei, Ying D.; Wania, Frank; Mitchell, Carl P. J.

2017-07-01

Analysis of high sulphur-containing samples for total mercury content using automated thermal decomposition, amalgamation, and atomic absorption spectroscopy instruments (USEPA Method 7473) leads to rapid and costly SO2 poisoning of catalysts. In an effort to overcome this issue, we tested whether the addition of powdered sodium carbonate (Na2CO3) to the catalyst and/or directly on top of sample material increases throughput of sulphur-impregnated (8-15 wt%) activated carbon samples per catalyst tube. Adding 5 g of Na2CO3 to the catalyst alone only marginally increases the functional lifetime of the catalyst (31 ± 4 g of activated carbon analyzed per catalyst tube) in relation to unaltered catalyst of the AMA254 total mercury analyzer (17 ± 4 g of activated carbon). Adding ≈ 0.2 g of Na2CO3 to samples substantially increases (81 ± 17 g of activated carbon) catalyst life over the unaltered catalyst. The greatest improvement is achieved by adding Na2CO3 to both catalyst and samples (200 ± 70 g of activated carbon), which significantly increases catalyst performance over all other treatments and enables an order of magnitude greater sample throughput than the unaltered samples and catalyst. It is likely that Na2CO3 efficiently sequesters SO2, even at high furnace temperatures to produce Na2SO4 and CO2, largely negating the poisonous impact of SO2 on the catalyst material. Increased corrosion of nickel sampling boats resulting from this methodological variation is easily resolved by substituting quartz boats. Overall, this variation enables an efficient and significantly more affordable means of employing automated atomic absorption spectrometry instruments for total mercury analysis of high-sulphur matrices.

Predicting the quality of powders for inhalation from surface energy and area.

PubMed

Cline, David; Dalby, Richard

2002-09-01

To correlate the surface energy of active and carrier components in an aerosol powder to in vitro performance of a passive dry powder inhaler. Inverse gas chromatography (IGC) was used to assess the surface energy of active (albuterol and ipratropium bromide) and carrier (lactose monohydrate, trehalose dihydrate and mannitol) components of a dry powder inhaler formulation. Blends (1%w/w) of drug and carrier were prepared and evaluated for dry powder inhaler performance by cascade impaction. The formulations were tested with either of two passive dry powder inhalers, Rotahaler (GlaxoSmithKline) or Handihaler (Boehringer Ingelheim). In vitro performance of the powder blends was strongly correlated to surface energy interaction between active and carrier components. Plotting fine particle fraction vs. surface energy interaction yielded an R2 value of 0.9283. Increasing surface energy interaction between drug and carrier resulted in greater fine particle fraction of drug. A convincing relationship, potentially useful for rapid formulation design and screening, was found between the surface energy and area parameters derived from IGC and dry powder inhaler performance.

21 CFR 177.1980 - Vinyl chloride-propylene copolymers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... contents of the cup are added 3.5 grams of granular sodium peroxide, 0.1 gram of powdered starch, and 0.02... applicable to vinyl chloride-propylene copolymers used in food-packaging adhesives complying with § 175.105...

21 CFR 177.1980 - Vinyl chloride-propylene copolymers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... contents of the cup are added 3.5 grams of granular sodium peroxide, 0.1 gram of powdered starch, and 0.02... applicable to vinyl chloride-propylene copolymers used in food-packaging adhesives complying with § 175.105...

Structural changes during milling of aluminum oxide powders

NASA Technical Reports Server (NTRS)

Ziepler, G.

1984-01-01

The mechanical activation of four fused corundum powders and a calcined Al2O3 powder was studied. The milled powders were characterized by their structural properties, crystallite size, and lattice distortions. Structural changes during milling, detected by X-ray line broadening analysis, gave information about the enhanced activity of the powders caused by the lattice distortions and by the decreasing crystallite size during milling. The structural changes during milling, under the same milling conditions, can be quite different for the same ceramic material, but with different characteristics in the as received state.

Effect of garlic powder on acrylamide formation in a low-moisture model system and bread baking.

PubMed

Li, Jinwang; Zuo, Jie; Qiao, Xuguang; Zhang, Yongju; Xu, Zhixiang

2016-02-01

Acrylamide (AA) is of concern worldwide because of its neurotoxicity, genotoxicity and reproductive/developmental toxicity. Consequently, methods for minimizing AA formation during food processing are vital. In this study, the formation and elimination of AA in an asparagine/glucose low-moisture model system were investigated by response surface methodology. The effect of garlic powder on the kinetics of AA formation/elimination was also evaluated. The AA content reached a maximum level (674.0 nmol) with 1.2 mmol of glucose and 1.2 mmol of asparagine after heating at 200 °C for 6 min. The AA content was greatly reduced with the addition of garlic powder. Compared to without garlic powder, an AA reduction rate of 43% was obtained with addition of garlic powder at a mass fraction of 0.05 g. Garlic powder inhibited AA formation during the generation-predominant kinetic stage and had no effect on the degradation-predominant kinetic stage. The effect of garlic powder on AA formation in bread and bread quality was also investigated. Adding a garlic powder mass fraction of 15 g to 500 g of dough significantly (P < 0.05) reduced the formation of AA (reduction rate of 46%) and had no obvious effect on the sensory qualities of the bread. This study provides a possible method for reducing the AA content in bread and other heat-treated starch-rich foods. © 2015 Society of Chemical Industry.

Discrimination of smokeless powders by headspace SPME-GC-MS and SPME-GC-ECD, and the potential implications upon training canine detection of explosives

NASA Astrophysics Data System (ADS)

Harper, Ross J.; Almirall, Jose R.; Furton, Kenneth G.

2005-05-01

This presentation will provide an odour analysis of a variety of smokeless powders & communicate the rapid SPME-GC-ECD method utilized. This paper will also discuss the implications of the headspace analysis of Smokeless Powders upon the choice of training aids for Explosives Detection Canines. Canine detection of explosives relies upon the dogs" ability to equate finding a given explosive odour with a reward, usually in the form of praise or play. The selection of explosives upon which the dogs are trained thus determines which explosives the canines can and potentially cannot find. Commonly, the training is focussed towards high explosives such as TNT and Composition 4, and the low explosives such as Black and Smokeless Powders are added often only for completeness. Powder explosives constitute a major component of explosive incidents throughout the US, and canines trained to detect explosives must be trained across the entire range of powder products. Given the variability in the manufacture and product make-up many smokeless powders do not share common odour chemicals, giving rise to concerns over the extensiveness of canine training. Headspace analysis of a selection of Smokeless Powders by Solid Phase Microextraction Gas Chromatography using Mass Spectrometry (SPME-GC-MS) and Electron Capture Detectors (SPME-GC-ECD) has highlighted significant differences in the chemical composition of the odour available from different brands. This suggests that greater attention should be paid towards the choice of Powder Explosives when assigning canine training aids.

A novel approach to determine the thermal transition of gum powder/hydro-gels using dynamic mechanical analysis

NASA Astrophysics Data System (ADS)

Nagamadhu, M.; Jeyaraj, P.; Kumar, G. C. Mohan

2018-04-01

The dynamic characterization of materials plays a major role in the present area. The many researchers are worked on solid materials and its characterization, it can be tested using dynamic mechanical analyzer (DMA), however, no such work on powder a semiliquid samples. The powder and liquid samples can also easily characterization as like solid samples using DMA. These powder samples are analyzed with a material pocket method which can be used to accurately determine very low levels of variation in powder properties, due to the high sensitivity of DMA to glass transitions. No such DMA studies on hydrogel and Gum powders. The gum powders are used in various applications start from food industries, pharmacy, natural gums paste, biomedical applications etc. among all this applications gum Ghatti is one of the powders using for varies applications. Around 50 milligrams of Ghatti powders are placed inside material pocket and analyzed storage modulus (G'), loss modulus (G″) and tan delta (δ). Also, understand the curing and glass transition effect using water, glycerin and superplastic from room temperature to 200°C. The result shows that storage modulus decreases with increase in temperature in pure Ghatti powder. The surprising improvement in storage modulus was found with an increase in temperature with addition of water, glycerin, and superplastic. However, loss modulus and tan delta are also having very significant influence and also shows a clear peak of the tan delta. The loss modulus results were found to be improved by adding solidifying agents, along with this water and superplastic better influence. But glycerine found to be hydrogel in nature and thermodynamic properties are much influenced by frequency.

Physical characteristics and aerosolization performance of insulin dry powders for inhalation prepared by a spray drying method.

PubMed

You, Yu; Zhao, Min; Liu, Guangli; Tang, Xing

2007-07-01

The objective of this study was to investigate the influence of formulation excipients on the physical characteristics and aerosolization performance of insulin dry powders for inhalation. Insulin dry powders were prepared by a spray drying technique using excipients such as sugars (trehalose, lactose and dextran), mannitol and amino acids (L-leucine, glycine and threonine). High performance liquid chromatography and the mouse blood glucose method were used for determination of the insulin content. The powder properties were determined and compared by scanning electron microscopy, thermo-gravimetric analysis and size distribution analysis by a time-of-flight technique. The in-vitro aerosolization behaviour of the powders was assessed with an Aerolizer inhaler using a twin-stage impinger. Powder yield and moisture absorption were also determined. Results showed that there was no noticeable change in insulin content in any of the formulations by both assay methods. All powders were highly wrinkled, with median aerodynamic diameters of 2-4 microm, and consequently suitable for pulmonary administration. The tapped density was reduced dramatically when glycine was added. The powders containing mannitol, with or without L-leucine, were less sensitive to moisture. The highest respirable fraction of 67.3 +/- 1.3% was obtained with the formulation containing L-leucine, in contrast to formulations containing glycine and threonine, which had a respirable fraction of 11.2 +/- 3.9% and 23.5 +/- 2.5%, respectively. In addition, powders with good physical properties were achieved by the combination of insulin and trehalose. This study suggests that L-leucine could be used to enhance the aerosolization behaviour of the insulin dry powders for inhalation, and trehalose could potentially be used as an excipient in the formulations.

Plasma methods of obtainment of multifunctional composite materials, dispersion-hardened by nanoparticles

NASA Astrophysics Data System (ADS)

Sizonenko, O. N.; Grigoryev, E. G.; Zaichenko, A. D.; Pristash, N. S.; Torpakov, A. S.; Lipyan, Ye V.; Tregub, V. A.; Zholnin, A. G.; Yudin, A. V.; Kovalenko, A. A.

2016-04-01

The new approach in developed plasma methods consists in that dispersionhardening additives (TiC, TiB2 in particular) are not mechanically added to powder mixture as additional component, as in conventional methods, but are instead synthesized during high voltage electric discharges (HVED) in disperse system “hydrocarbon liquid - powder” preservation of ultrafine structure is ensured due to use of spark plasma sintering (SPS) as a consolidation method. HVED in disperse system “hydrocarbon liquid - powder” due to impact of plasma discharge channel, electromagnetic fields, shock waves mechanical impact, hydro flows and volume microcavitation leads to synthesis of nanocarbon, metal powders dispersion and synthesis of micro- (from 10-6 to 10-7 m) and nanosized (from 10-7 to 10-9 m) composite powders of hardening phases. SPS is the passage of pulsed current (superposition of direct and alternating current) through powder with the simultaneous mechanical compressing. The formation of plasma is initiated in gaseous phase that fills gaps between particles. SPS allows targeted control of grain growth rate and thus allows obtainment of multifunctional composite materials dispersion hardened by nanoparticles. Processes of HVED synthesis of micro- and nanosized powders of new compositions from elemental metal powders and their mixtures with the subsequent application of high-speed SPS of obtained powders create conditions for increase of strength (by 10 - 20%), hardness and wear-resistance (by 30 - 60%) of obtained materials.

Microencapsulation of Natural Anthocyanin from Purple Rosella Calyces by Freeze Drying

NASA Astrophysics Data System (ADS)

Nafiunisa, A.; Aryanti, N.; Wardhani, D. H.; Kumoro, A. C.

2017-11-01

Anthocyanin extract in powder form will improve its use since the powder is easier to store and more applicable. Microencapsulation method is introduced as an efficient way for protecting pigment such as anthocyanin. This research was aimed to characterise anthocyanin encapsulated products prepared from purple Roselle calyces by freeze drying. The liquid anthocyanin extracts from ultrasound-assisted extraction were freeze-dried with and without the addition of 10% w/w maltodextrins as a carrier and coating agents. The quality attributes of the powders were characterised by their colour intensity, water content, and solubility. Analysis of encapsulated material was performed for the powder added by maltodextrin. The stability of the microencapsulated pigment in solution form was determined for 11 days. Total anthocyanin content was observed through pH differential method. The results of the colour intensity analysis confirm that the product with maltodextrin addition has more intense colour with L* value of 29.69 a* value of 54.29 and b* value of 8.39. The result with the addition of maltodextrin has less moisture content and more soluble in water. It is verified that better results were obtained for powder with maltodextrin addition. Anthocyanin in the powder form with maltodextrin addition exhibits higher stability even after 11 days. In conclusion, the microencapsulation of anthocyanin with maltodextrin as a carrier and coating agent presented a potential method to produce anthocyanin powder from purple Roselle.

Preparation of TiO₂ nanocrystallite powders coated with 9 mol% ZnO for cosmetic applications in sunscreens.

PubMed

Ko, Horng-Huey; Chen, Hui-Ting; Yen, Feng-Ling; Lu, Wan-Chen; Kuo, Chih-Wei; Wang, Moo-Chin

2012-01-01

The preparation of TiO(2) nanocrystallite powders coated with and without 9 mol% ZnO has been studied for cosmetic applications in sunscreens by a co-precipitation process using TiCl(4) and Zn(NO(3))(2)·6H(2)O as starting materials. XRD results show that the phases of anatase TiO(2) and rutile TiO(2) coexist for precursor powders without added ZnO (T-0Z) and calcined at 523 to 973 K for 2 h. When the T-0Z precursor powders are calcined at 1273 K for 2 h, only the rutile TiO(2) appears. In addition, when the TiO(2) precursor powders contain 9 mol% ZnO (T-9Z) are calcined at 873 to 973 K for 2 h, the crystallized samples are composed of the major phase of rutile TiO(2) and the minor phases of anatase TiO(2) and Zn(2)Ti(3)O(8). The analyses of UV/VIS/NIR spectra reveal that the absorption of the T-9Z precursor powders after being calcined has a red-shift effect in the UV range with increasing calcination temperature. Therefore, the TiO(2) nanocrystallite powders coated with 9 mol% ZnO can be used as the attenuate agent in the UV-A region for cosmetic applications in sunscreens.

Preparation of TiO2 Nanocrystallite Powders Coated with 9 mol% ZnO for Cosmetic Applications in Sunscreens

PubMed Central

Ko, Horng-Huey; Chen, Hui-Ting; Yen, Feng-Ling; Lu, Wan-Chen; Kuo, Chih-Wei; Wang, Moo-Chin

2012-01-01

The preparation of TiO2 nanocrystallite powders coated with and without 9 mol% ZnO has been studied for cosmetic applications in sunscreens by a co-precipitation process using TiCl4 and Zn(NO3)2·6H2O as starting materials. XRD results show that the phases of anatase TiO2 and rutile TiO2 coexist for precursor powders without added ZnO (T-0Z) and calcined at 523 to 973 K for 2 h. When the T-0Z precursor powders are calcined at 1273 K for 2 h, only the rutile TiO2 appears. In addition, when the TiO2 precursor powders contain 9 mol% ZnO (T-9Z) are calcined at 873 to 973 K for 2 h, the crystallized samples are composed of the major phase of rutile TiO2 and the minor phases of anatase TiO2 and Zn2Ti3O8. The analyses of UV/VIS/NIR spectra reveal that the absorption of the T-9Z precursor powders after being calcined has a red-shift effect in the UV range with increasing calcination temperature. Therefore, the TiO2 nanocrystallite powders coated with 9 mol% ZnO can be used as the attenuate agent in the UV-A region for cosmetic applications in sunscreens. PMID:22408415

Effect of NaCl addition during diafiltration on the solubility, hydrophobicity, and disulfide bonds of 80% milk protein concentrate powder.

PubMed

Mao, X Y; Tong, P S; Gualco, S; Vink, S

2012-07-01

We investigated the surface hydrophobicity index based on different fluorescence probes [1-anilinonaphthalene-8-sulfonic acid (ANS) and 6-propionyl-2-(N,N-dimethylamino)-naphthalene (PRODAN)], free sulfhydryl and disulfide bond contents, and particle size of 80% milk protein concentrate (MPC80) powders prepared by adding various amounts of NaCl (0, 50, 100, and 150 mM) during the diafiltration process. The solubility of MPC80 powder was not strictly related to surface hydrophobicity. The MPC80 powder obtained by addition of 150 mM NaCl during diafiltration had the highest solubility but also the highest ANS-based surface hydrophobicity, the lowest PRODAN-based surface hydrophobicity, and the least aggregate formation. Intermolecular disulfide bonds caused by sulfhydryl-disulfide interchange reactions and hydrophobic interactions may be responsible for the lower solubility of the control MPC80 powder. The enhanced solubility of MPC80 powder with addition of NaCl during diafiltration may result from the modified surface hydrophobicity, the reduced intermolecular disulfide bonds, and the associated decrease in mean particle size. Addition of NaCl during the diafiltration process can modify the strength of hydrophobic interactions and sulfhydryl-disulfide interchange reactions and thereby affect protein aggregation and the solubility of MPC powders. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Adsorption kinetics of SO2 on powder activated carbon

NASA Astrophysics Data System (ADS)

Li, Bing; Zhang, Qilong; Ma, Chunyuan

2018-02-01

The flue gas SO2 adsorption removal by powder activated carbon is investigated based on a fixed bed reactor. The effect of SO2 inlet concentration on SO2 adsorption is investigated and the adsorption kinetics is analyzed. The results indicated that the initial SO2 adsorption rate and the amount of SO2 adsorbed have increased with increased in SO2 inlet concentration. Gas diffusion, surface adsorption and catalytic oxidation reaction are involved in SO2 adsorption on powder activated carbon, which play a different role in different stage. The Bangham kinetics model can be used to predict the kinetics of SO2 adsorption on powder activated carbon.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1992-04-21

A free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7 [times] 10[sup [minus]3] to about 7 [times] 10[sup [minus]2] microns and the pcm must be added to the silica in an amount of 80 wt. % or less pcm per combined weight of silica and pcm. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a pcm material. The silica-pcm mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub. 9 figs.

Powder-metallurgical preparation of A15 superconductors

NASA Astrophysics Data System (ADS)

Wilhelm, Manfred; Wohlleben, Karl; Springer, Engelbert; Mrowiec, Klaus; Schaper, Wilfried; Wecker, Joachim

1985-08-01

The powder-metallurgical preparation of Cu-Nb3Sn microcomposite superconductors was investigated in order to economize in the manufacture of the conductors and to improve their mechanical and electrical properties. Conditions during high temperature extrusion are optimized by adding Al or Ti as reducing agents, also with a view to the following cold forming. Current densities well above 10,000 A/sq cm at 15T are obtained by applying coarse-grained Nb powder and incorporating small quantities of Ta or Ti. The current carrying behavior of the conductors was determined as a function of the degree of mechanical deformation, the cold forming technique, and the heat treatment conditions. Wires containing an internal tin source as well as bundled assemblies for high current applications were manufactured. Long wires can be produced.

Stability of a novel corticosteroid nasal irrigation solution: betamethasone 17-valerate added to extemporaneously prepared nasal irrigation solutions.

PubMed

Ong, Kheng Yong; Lim, Wei Ching; Ooi, Shing Ming; Loh, Zhi Hui; Kong, Ming Chai; Chan, Lai Wah; Heng, Paul Wan Sia

2017-05-01

There are no commercially available nasal irrigation solutions containing corticosteroids. Instead, such preparations are extemporaneously prepared by adding existing corticosteroid formulations to nasal irrigation solutions. The stability of the corticosteroid betamethasone 17-valerate (B17V), in nasal irrigation solutions of different compositions and pH and stored under different temperatures, was studied to determine the optimal choice of solution and storage conditions. Triplicate extemporaneous preparations made with B17V were prepared by adding a predetermined volume of B17V lotion to each nasal irrigation solution: normal saline (NS), sodium bicarbonate (NaHCO 3 ) powder dissolved in tap water, and a commercially available powder mixture (FLO Sinus Care Powder), dissolved in tap water or pre-boiled tap water. Preparations were stored at 30°C and 4°C. Sampling was carried out at 0, 1, 2, 6, and 24 hours. The concentrations of B17V and its degradation compound, betamethasone 21-valerate (B21V), were determined by high-performance liquid chromatography. Preparations stored at 30°C contained a lower amount of B17V and higher amount of B21V than those stored at 4°C. B17V stability in nasal irrigation solutions decreased in the following order: NS, FLO in fresh tap water, FLO in pre-boiled tap water, and NaHCO 3 . The degradation rate of B17V increased with higher storage temperature and higher pH. B17V is most stable when added to NS and least stable in NaHCO 3 solution. FLO solution prepared with either cooled boiled water or tap water is an alternative if administered immediately. Storage at 4°C can better preserve stability of B17V, over a period of 24 hours. © 2017 ARS-AAOA, LLC.

Use of natural antimicrobials to improve the control of Listeria monocytogenes in a cured cooked meat model system.

PubMed

Xi, Y; Sullivan, G A; Jackson, A L; Zhou, G H; Sebranek, J G

2011-07-01

Concern about nitrite in processed meats has increased consumer demand for natural products manufactured without nitrite or nitrate. Studies on commercial meat products labeled as "Uncured" and "No-Nitrite-or-Nitrate-Added" have shown less control of nitrite in these products and greater potential growth of bacterial pathogens. To improve the safety of the "naturally cured" meats, several natural ingredients were studied in a cured cooked meat model system (80:20 pork, 10% water, 2% salt, and 150 or 50 ppm ingoing sodium nitrite) that closely resembled commercial frankfurters to determine their inhibitory effect on Listeria monocytogenes. Results showed that cranberry powder at 1%, 2% and 3% resulted in 2-4 log cfu/g less growth of L. monocytogenes compared to the control with nitrite alone (P<0.05). Other natural compounds, such as cherry powder, lime powder and grape seed extract, also provided measureable inhibition to L. monocytogenes when combined with cranberry powder (P<0.05). Copyright © 2011 Elsevier Ltd. All rights reserved.

[Determination method of polysorbates in powdered soup by HPLC].

PubMed

Takeda, Y; Abe, Y; Ishiwata, H; Yamada, T

2001-04-01

A method for qualitative and quantitative analyses of polysorbates in powdered soup by HPLC was studied. Polysorbates in samples were extracted with acetonitrile after rinsing with n-hexane to remove fats and oils. The extract was cleaned up using a Bond Elut silica gel cartridge (500 mg). The cartridge was washed with ethyl acetate and polysorbates were eluted with a small amount of acetonitrile-methanol (1:2) mixture. The eluate was treated with cobalt thiocyanate solution to form a blue complex with polysorbate. In order to determine polysorbate, the complex was subjected to HPLC with a GPC column, using a mixture of acetonitrile-water (95:5) as a mobile phase, with a detection wavelength of 620 nm. The recoveries of polysorbate 80 added to powdered soups were more than 75% and the determination limit was 0.04 mg/g. When the proposed method was applied to the determination of polysorbates in 16 commercial samples of powdered soup for instant noodles and seasoning consomme, no polysorbates were detected in any sample.

Preparing ultrafine PbS powders from the scrap lead-acid battery by sulfurization and inert gas condensation

NASA Astrophysics Data System (ADS)

Xia, Huipeng; Zhan, Lu; Xie, Bing

2017-02-01

A novel method for preparing ultrafine PbS powders involving sulfurization combined with inert gas condensation is developed in this paper, which is applicable to recycle Pb from lead paste of spent lead-acid batteries. Initially, the effects of the evaporation and condensation temperature, the inert gas pressure, the condensation distance and substrate on the morphology of as-obtained PbS ultrafine particles are intensively investigated using sulfur powders and lead particles as reagents. Highly dispersed and homogeneous PbS nanoparticles can be prepared under the optimized conditions which are 1223 K heating temperature, 573 K condensation temperature, 100 Pa inert gas pressure and 60 cm condensation distance. Furthermore, this method is successfully applied to recycle Pb from the lead paste of spent lead acid battery to prepare PbS ultrafine powders. This work does not only provide the theoretical fundamental for PbS preparation, but also provides a novel and efficient method for recycling spent lead-acid battery with high added-value products.

Effect of process technology on the nutritional, functional, and physical quality of grapefruit powder.

PubMed

Agudelo, C; Igual, M; Camacho, M M; Martínez-Navarrete, N

2017-01-01

The health properties of fruit are widely known. Powdered fruit may be a practical format to be offered to the consumer. Nevertheless, the process used to obtain the powder must ensure the maximum retention of the bioactive compounds and the functional value of the fruit while retaining adequate physical properties. The aim of this study was to compare freeze-drying and spray drying as the drying technologies to obtain grapefruit powder. The obtained results allow freeze-drying to be proposed as a better technology than spray drying in order to obtain a product with a higher content of vitamin C and total carotenoids. Moreover, all of the edible part of the fruit is used in this case, so a greater quantity of healthy compounds is preserved and by-product generation is avoided. Adding about 6 g water, 4 g Arabic gum and 0.6 g bamboo fibre/100 g grapefruit pulp is recommended before freeze-drying. © The Author(s) 2016.

Microbial characterization and degradation of linear alkylbenzene sulfonate in an anaerobic reactor treating wastewater containing soap powder.

PubMed

Carosia, Mariana Fronja; Okada, Dagoberto Yukio; Sakamoto, Isabel Kimiko; Silva, Edson Luiz; Varesche, Maria Bernadete Amâncio

2014-09-01

The aim of this study was to evaluate the removal of linear alkylbenzene sulfonate (LAS) in an anaerobic fluidized bed reactor (AFBR) treating wastewater containing soap powder as LAS source. At Stage I, the AFBR was fed with a synthetic substrate containing yeast extract and ethanol as carbon sources, and without LAS; at Stage II, soap powder was added to this synthetic substrate obtaining an LAS concentration of 14 ± 3 mg L(-1). The compounds of soap powder probably inhibited some groups of microorganisms, increasing the concentration of volatile fatty acids (VFA) from 91 to 143 mg HAc L(-1). Consequently, the LAS removal rate was 48 ± 10% after the 156 days of operation. By sequencing, 16S rRNA clones belonging to the phyla Proteobacteria and Synergistetes were identified in the samples taken at the end of the experiment, with a remarkable presence of Dechloromonas sp. and Geobacter sp. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of a novel dry powder inhalation formulation for the delivery of rivastigmine hydrogen tartrate.

PubMed

Simon, Alice; Amaro, Maria Inês; Cabral, Lucio Mendes; Healy, Anne Marie; de Sousa, Valeria Pereira

2016-03-30

The purpose of this study was to prepare engineered particles of rivastigmine hydrogen tartrate (RHT) and to characterize the physicochemical and aerodynamic properties, in comparison to a lactose carrier formulation (LCF). Microparticles were prepared from ethanol/water solutions containing RHT with and without the incorporation of L-leucine (Leu), using a spray dryer. Dry powder inhaler formulations prepared were characterized by scanning electron microscopy, powder X-ray diffraction, laser diffraction particle sizing, ATR-FTIR, differential scanning calorimetry, bulk and tapped density, dynamic vapour sorption and in vitro aerosol deposition behaviour using a next generation impactor. The smooth-surfaced spherical morphology of the spray dried microparticles was altered by adding Leu, resulting in particles becoming increasingly wrinkled with increasing Leu. Powders presented low densities. The glass transition temperature was sufficiently high (>90 °C) to suggest good stability at room temperature. As Leu content increased, spray dried powders presented lower residual solvent content, lower particle size, higher fine particle fraction (FPF<5 μm), and lower mass median aerodynamic diameter (MMAD). The LCF showed a lower FPF and higher MMAD, relative to the spray dried formulations containing more than 10% Leu. Spray dried RHT powders presented better aerodynamic properties, constituting a potential drug delivery system for oral inhalation. Copyright © 2016. Published by Elsevier B.V.

Tailoring the thermal conductivity of the powder bed in Electron Beam Melting (EBM) Additive Manufacturing.

PubMed

Smith, C J; Tammas-Williams, S; Hernandez-Nava, E; Todd, I

2017-09-05

Metallic powder bed additive manufacturing is capable of producing complex, functional parts by repeatedly depositing thin layers of powder particles atop of each other whilst selectively melting the corresponding part cross-section into each layer. A weakness with this approach arises when melting overhanging features, which have no prior melted material directly beneath them. This is due to the lower thermal conductivity of the powder relative to solid material, which as a result leads to an accumulation of heat and thus distortion. The Electron Beam Melting (EBM) process alleviates this to some extent as the powder must first be sintered (by the beam itself) before it is melted, which results in the added benefit of increasing the thermal conductivity. This study thus sought to investigate to what extent the thermal conductivity of local regions in a titanium Ti-6Al-4V powder bed could be varied by imparting more energy from the beam. Thermal diffusivity and density measurements were taken of the resulting sintered samples, which ranged from being loosely to very well consolidated. It was found that the calculated thermal conductivity at two temperatures, 40 and 730 °C, was more than doubled over the range of input energies explored.

Effects of milling media on the fabrication of melt-derived bioactive glass powder for biomaterial application

NASA Astrophysics Data System (ADS)

Ibrahim, Nurul Farhana; Mohamad, Hasmaliza; Noor, Siti Noor Fazliah Mohd

2016-12-01

The present work aims to study the effects of using different milling media on bioactive glass produced through melt-derived method for biomaterial application. The bioactive glass powder based on SiO2-CaO-Na2O-P2O5 system was fabricated using two different types of milling media which are tungsten carbide (WC) and zirconia (ZrO2) balls. However, in this work, no P2O5 was added in the new composition. XRF analysis indicated that tungsten trioxide (WO3) was observed in glass powder milled using WC balls whereas ZrO2 was observed in glass powder milled using ZrO2 balls. Amorphous structure was detected with no crystalline peak observed through XRD analysis for both glass powders. FTIR analysis confirmed the formation of silica network with the existence of functional groups Si-O-Si (bend), Si-O-Si (tetrahedral) and Si-O-Si (stretch) for both glass powders. The results revealed that there was no significant effect of milling media on amorphous silica network glass structure which shows that WC and zirconia can be used as milling media for bioactive glass fabrication without any contamination. Therefore, the fabricated BG can be tested safely for bioactivity assessment in biological fluids environment.

Physicochemical and Sensory Properties of Appenzeller Cheese Supplemented with Powdered Microcapsule of Tomato Extract during Ripening

PubMed Central

Kwak, Hae-Soo; Chimed, Chogsom; Yoo, Sang-Hun

2016-01-01

The objective of this study was to determine the physicochemical and sensory properties of Appenzeller cheese supplemented with different concentrations (0, 1, 2, 3, and 4%, w/w) of powdered microcapsules of tomato extracts (PMT) during ripening at 14℃ for 6 mon. The particle sizes of PMT ranged from 1 to 10 m diameter with an average particle size of approximately 2 m. Butyric acid (C4) concentrations of PMT-added Appenzeller cheese were significantly higher than that of the control. Lactic acid bacteria counts in the cheese were not significantly influenced by ripening time from 0 to 6 mon or the concentrations (0-4%, w/w) of PMT. In terms of texture, the hardness of PMT-added Appenzeller cheese was significantly increased compared to the control. The gumminess and chewiness of PMT-added Appenzeller cheese were similar to those of the control. However, both cohesiveness and springiness of PMT-added Appenzeller cheese were slightly decreased. In sensory analysis, bitterness and sourness of Appenzeller cheese were not significantly changed after supplementation of PMT, but sweetness of the cheese was significantly increased after increasing the ripening time from 0 to 6 mon and increasing the concentration from 1 to 4% (w/w). Based on these results, the addition of the concentrations (1-4%, w/w) of PMT to Appenzeller cheese can be used to develop functional Appenzeller cheese. PMID:27194934

Antibacterial Property of Cold-Sprayed HA-Ag/PEEK Coating

NASA Astrophysics Data System (ADS)

Sanpo, Noppakun; Tan, Meng Lu; Cheang, Philip; Khor, K. A.

2009-03-01

The antibacterial behavior of HA-Ag (silver-doped hydroxyapatite) nanopowder and their composite coatings were investigated against Escherichia coli (DH5α). HA-Ag nanopowder and PEEK (poly-ether-ether-ketone)-based HA-Ag composite powders were synthesized using in-house powder processing techniques. Bacteria culture assay of HA-Ag nanopowder and their composite powders displayed excellent bacteriostatic activity against E. coli. The antibacterial activity increased with increasing concentration of HA-Ag nanoparticle in these composite powders. These nanocomposite powders were subsequently used as feedstock to generate antibacterial coatings via cold spray technology. The ratios of HA-Ag to PEEK in their composite powders were 80:20, 60:40, 40:60, and 20:80 (wt.%). Microstructural characterization and phase analysis of feedstock powders and as-deposited coatings were carried out using FESEM/EDX and XRD. Antibacterial nanocomposite HA-Ag/PEEK coatings were successfully deposited using cold spraying parameters of 11-12 bars at preheated air temperature between 150 and 160 °C. These as-sprayed coatings of HA-Ag/PEEK composite powders comprising varying HA-Ag and PEEK ratios retained their inherent antibacterial property as verified from bacterial assay. The results indicated that the antibacterial activity increased with increasing HA-Ag nanopowder concentration in the composite powder feedstock and cold-sprayed coating.

Bulk synthesis of polypyrrole nanofibers by a seeding approach.

PubMed

Zhang, Xinyu; Manohar, Sanjeev K

2004-10-13

The morphology of doped polypyrrole.Cl powder changes dramatically from granular to nanofibrillar when a very small amount (1-4 mg) of V2O5 nanofibers are added to a chemical oxidative polymerization of pyrrole in aq 1.0 M HCl using (NH4)2S2O8 as the oxidant. Unlike the polyaniline system, a key synthetic requirement in the polypyrrole system is for the seed template to be "active", i.e., to be capable of independently oxidizing the pyrrole monomer. Thin, strongly adherent films can be obtained on inert surfaces such as glass, plastics, etc., directly from the polymerization mixture without any bulk product isolation steps, significantly simplifying the processing of these nanofibers.

Ceramic Inclusions in Powder Metallurgy Disk Alloys: Characterization and Modeling

NASA Technical Reports Server (NTRS)

Bonacuse, Peter J.

2001-01-01

Powder metallurgy alloys are increasingly used in gas turbine engines, especially in turbine disk applications. Although powder metallurgy materials have many advantages over conventionally cast and wrought alloys (higher strength, higher temperature capability, etc.), they suffer from the rare occurrence of ceramic defects (inclusions) that are inherent to the powder atomization process. These inclusions can have a potentially large detrimental effect on the durability of individual components. An inclusion in a high stress location can act as a site for premature crack initiation and thereby considerably reduce the fatigue life. Because these inclusions are exceedingly rare, they typically do not reveal themselves in the process of characterizing the material for a particular application (the cumulative volume of the test bars in a fatigue life characterization is typically on the order of a single actual component). Ceramic inclusions have, however, been found to be the root cause of a number of catastrophic engine failures. To investigate the effect of these inclusions in detail, we have undertaken a study where known populations of ceramic particles, whose composition and morphology are designed to mimic the "natural" inclusions, are added to the precursor powder. Surface-connected inclusions have been found to have a particularly large detrimental effect on fatigue life; therefore, the quantity of ceramic "seeds" added is calculated to ensure that a minimum number will intersect the surface of the fatigue test bars. Because the ceramic inclusions are irregularly shaped and have a tendency to break up in the process of extrusion and forging, a method of calculating the probability of occurrence and expected intercepted surface area was needed. We have developed a Monte Carlo simulation to determine the distributions of these parameters and have verified the simulated results with observations of ceramic inclusions found in macroscopic slices from extrusions and forgings. Fatigue specimens have been machined from Udimet 720 (a powder metallurgy superalloy) forgings, to determine the effects of the inclusions on fatigue life. The ultimate goal of this study will be to use probabilistic methods to determine the reliability detriment that can be attributed to these ceramic inclusions. This work has been supported by the Ultra Safe and Ultra- Efficient Engine Technologies programs.

Impedance spectroscopic analysis of composite electrode from activated carbon/conductive materials/ruthenium oxide for supercapacitor applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taer, E.; Awitdrus,; Farma, R.

Activated carbon powders (ACP) were produced from the KOH treated pre-carbonized rubber wood sawdust. Different conductive materials (graphite, carbon black and carbon nanotubes (CNTs)) were added with a binder (polivinylidene fluoride (PVDF)) into ACP to improve the supercapacitive performance of the activated carbon (AC) electrodes. Symmetric supercapacitor cells, fabricated using these AC electrodes and 1 molar H{sub 2}SO{sub 4} electrolyte, were analyzed using a standard electrochemical impedance spectroscopy technique. The addition of graphite, carbon black and CNTs was found effective in reducing the cell resistance from 165 to 68, 23 and 49 Ohm respectively, and increasing the specific capacitance ofmore » the AC electrodes from 3 to 7, 17, 32 F g{sup −1} respectively. Since the addition of CNTs can produce the highest specific capacitance, CNTs were chosen as a conductive material to produce AC composite electrodes that were added with 2.5 %, 5 % and 10 % (by weight) electro-active material namely ruthenium oxide; PVDF binder and CNTs contents were kept at 5 % by weight in each AC composite produced. The highest specific capacitance of the cells obtained in this study was 86 F g{sup −1}, i.e. for the cell with the resistance of 15 Ohm and composite electrode consists of 5 % ruthenium oxide.« less

L-Leucine as an excipient against moisture on in vitro aerosolization performances of highly hygroscopic spray-dried powders.

PubMed

Li, Liang; Sun, Siping; Parumasivam, Thaigarajan; Denman, John A; Gengenbach, Thomas; Tang, Patricia; Mao, Shirui; Chan, Hak-Kim

2016-05-01

L-Leucine (LL) has been widely used to enhance the dispersion performance of powders for inhalation. LL can also protect powders against moisture, but this effect is much less studied. The aim of this study was to investigate whether LL could prevent moisture-induced deterioration in in vitro aerosolization performances of highly hygroscopic spray-dried powders. Disodium cromoglycate (DSCG) was chosen as a model drug and different amounts of LL (2-40% w/w) were added to the formulation, with the aim to explore the relationship between powder dispersion, moisture protection and physicochemical properties of the powders. The powder formulations were prepared by spray drying of aqueous solutions containing known concentrations of DSCG and LL. The particle sizes were measured by laser diffraction. The physicochemical properties of fine particles were characterized by X-ray powder diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic vapor sorption (DVS). The surface morphology and chemistry of fine particles were analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS). In vitro aerosolization performances were evaluated by a next generation impactor (NGI) after the powders were stored at 60% or 75% relative humidity (RH), and 25°C for 24h. Spray-dried (SD) DSCG powders were amorphous and absorbed 30-45% (w/w) water at 70-80% RH, resulting in deterioration in the aerosolization performance of the powders. LL did not decrease the water uptake of DSCG powders, but it could significantly reduce the effect of moisture on aerosolization performances. This is due to enrichment of crystalline LL on the surface of the composite particles. The effect was directly related to the percentage of LL coverage on the surface of particles. Formulations having 61-73% (molar percent) of LL on the particle surface (which correspond to 10-20% (w/w) of LL in the bulk powders) could minimize moisture-induced deterioration in the aerosol performance. In conclusion, particle surface coverage of LL can offer short-term protection against moisture on dispersion of hygroscopic powders. Copyright © 2016 Elsevier B.V. All rights reserved.

16 CFR 1209.35 - Product specification.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and address of each chemical supplier. Where the chemical composition or formula of a commercially pre..., identifying the extent of impurities allowed. (3) The formulation of the fire-retardant chemicals added, including their chemical constituents and their form (for example, granulated, powdered, or liquid); the...

16 CFR 1209.35 - Product specification.

Code of Federal Regulations, 2012 CFR

2012-01-01

... and address of each chemical supplier. Where the chemical composition or formula of a commercially pre..., identifying the extent of impurities allowed. (3) The formulation of the fire-retardant chemicals added, including their chemical constituents and their form (for example, granulated, powdered, or liquid); the...

16 CFR 1209.35 - Product specification.

Code of Federal Regulations, 2014 CFR

2014-01-01

... and address of each chemical supplier. Where the chemical composition or formula of a commercially pre..., identifying the extent of impurities allowed. (3) The formulation of the fire-retardant chemicals added, including their chemical constituents and their form (for example, granulated, powdered, or liquid); the...

76 FR 58533 - Powder River Regional Coal Team Activities; Notice of Public Meeting in Casper, WY

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-21

... DEPARTMENT OF THE INTERIOR Bureau of Land Management [LLWYP00000-L13200000-EL0000] Powder River Regional Coal Team Activities; Notice of Public Meeting in Casper, WY AGENCY: Bureau of Land Management, Interior. ACTION: Notice of Public Meeting. SUMMARY: The Powder River Regional Coal Team (RCT) has...

78 FR 23951 - Powder River Regional Coal Team Activities: Notice of Public Meeting in Casper, Wyoming

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

... DEPARTMENT OF THE INTERIOR Bureau of Land Management [LLWY922000-L13200000-EL0000] Powder River Regional Coal Team Activities: Notice of Public Meeting in Casper, Wyoming AGENCY: Bureau of Land Management, Interior. ACTION: Notice of public meeting. SUMMARY: The Powder River Regional Coal Team (RCT...

Mechanical alloying of lanthana-bearing nanostructured ferritic steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Somayeh Paseban; Indrajit Charit; Yaqiao Q. Wu

2013-09-01

A novel nanostructured ferritic steel powder with the nominal composition Fe–14Cr–1Ti–0.3Mo–0.5La2O3 (wt.%) was developed via high energy ball milling. La2O3 was added to this alloy instead of the traditionally used Y2O3. The effects of varying the ball milling parameters, such as milling time, steel ball size and ball to powder ratio, on the mechanical properties and micro structural characteristics of the as-milled powder were investigated. Nanocrystallites of a body-centered cubic ferritic solid solution matrix with a mean size of approximately 20 nm were observed by transmission electron microscopy. Nanoscale characterization of the as-milled powder by local electrode atom probe tomographymore » revealed the formation of Cr–Ti–La–O-enriched nanoclusters during mechanical alloying. The Cr:Ti:La:O ratio is considered “non-stoichiometric”. The average size (radius) of the nanoclusters was about 1 nm, with number density of 3.7 1024 m3. The mechanism for formation of nanoclusters in the as-milled powder is discussed. La2O3 appears to be a promising alternative rare earth oxide for future nanostructured ferritic steels.« less

Evaluation of plant-based natural coagulants for municipal wastewater treatment.

PubMed

Maurya, Sandhya; Daverey, Achlesh

2018-01-01

In this study, four plant-based natural coagulants (banana peel powder, banana stem juice, papaya seed powder and neem leaf powder) were evaluated for the removal of turbidity, chemical oxygen demand (COD) and total suspended solids (TSS) from municipal wastewater. The experiments were conducted at room temperature without adjusting the initial pH. The maximum turbidity removal was observed with banana peel powder (59.6%) at 0.4 g/L of dosage. Papaya seed powder and banana stem juice were the most effective for TSS removal (66.66%) and COD removal (66.67%), respectively. Significant linear relationships between turbidity and TSS ( R 2  = 0.67-0.88) and turbidity removals and COD removals ( R 2  = 0.68-0.8) were observed. Interestingly, all the natural coagulants tested in the study did not change the pH of the wastewater, which is an added advantage. FTIR analysis of banana peels revealed that functional groups such as carboxylic acid, hydroxyl and aliphatic amines might be responsible for promoting the coagulation-flocculation by neutralizing the charge on impurities in water. Overall, the results suggest the potential of low-cost natural coagulants in municipal wastewater treatment.

Water Atomization of Barium Fluoride: Calcium Fluoride for Enhanced Flow Characteristics of PS304 Feedstock Powder Blend

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.; DellaCorte, Christopher

2003-01-01

PS304 is a plasma spray deposited solid lubricant coating with feedstock composed of NiCr, Cr2O3, Ag, and BaF2-CaF2 powders. The effects of rounded BaF2-CaF2 particles on the gravity-fed flow characteristics of PS304 feedstock have been investigated. The BaF2-CaF2 powder was fabricated by water atomization using four sets of process parameters. Each of these powders was then characterized by microscopy and classified by screening to obtain 45 to 106 micron particles and added incrementally from 0 to 10 wt% to the other constituents of the PS304 feedstock, namely nichrome, chromia, and silver powders. The relationship between feedstock flow rate, measured with the Hall flowmeter, and concentration of fluorides was found to be linear in each case. The slopes of the lines were between those of the linear relationships previously reported using angular and spherical fluorides and were closer to the relationship predicted using the rule of mixtures. The results offer a fluoride fabrication technique potentially more cost-effective than gas atomization processes or traditional comminution processes.

Ceramic Inclusions In Powder Metallurgy Disk Alloys: Characterization and Modeling

NASA Technical Reports Server (NTRS)

Bonacuse, Pete; Kantzos, Pete; Telesman, Jack

2002-01-01

Powder metallurgy alloys are increasingly used in gas turbine engines, especially as the material chosen for turbine disks. Although powder metallurgy materials have many advantages over conventionally cast and wrought alloys (higher strength, higher temperature capability, etc.), they suffer from the rare occurrence of ceramic defects (inclusions) that arise from the powder atomization process. These inclusions can have potentially large detrimental effect on the durability of individual components. An inclusion in a high stress location can act as a site for premature crack initiation and thereby considerably reduce the fatigue life. Because these inclusions are exceedingly rare, they usually don't reveal themselves in the process of characterizing the material for a particular application (the cumulative volume of the test bars in a fatigue life characterization is typically on the order of a single actual component). Ceramic inclusions have, however, been found to be the root cause of a number of catastrophic engine failures. To investigate the effect of these inclusions in detail, we have undertaken a study where a known population of ceramic particles, whose composition and morphology are designed to mimic the 'natural' inclusions, are added to the precursor powder. Surface connected inclusions have been found to have a particularly large detrimental effect on fatigue life, therefore the volume of ceramic 'seeds' added is calculated to ensure that a minimum number will occur on the surface of the fatigue test bars. Because the ceramic inclusions are irregularly shaped and have a tendency to break up in the process of extrusion and forging, a method of calculating the probability of occurrence and expected intercepted surface and embedded cross-sectional areas were needed. We have developed a Monte Carlo simulation to determine the distributions of these parameters and have verified the simulated results with observations of ceramic inclusions found in macro slices from extrusions and forgings. The ultimate goal of this study will be to use probabilistic methods to determine the reliability detriment that can be attributed to these ceramic inclusions.

Bioavailability of elemental iron powders to rats is less than bakery-grade ferrous sulfate and predicted by iron solubility and particle surface area.

PubMed

Swain, James H; Newman, Samuel M; Hunt, Janet R

2003-11-01

Foods are fortified with elemental forms of iron to reduce iron deficiency. However, the nutritional efficacy of current, commercially produced elemental iron powders has not been verified. We determined the bioavailability of six commercial elemental iron powders and examined how physicochemistry influences bioavailability. Relative biological value (RBV) of the iron powders was determined using a hemoglobin repletion/slope ratio method, treating iron-deficient rats with repletion diets fortified with graded quantities of iron powders, bakery-grade ferrous sulfate or no added iron. Iron powders were assessed physicochemically by measuring iron solubility in hydrochloric acid at pH 1.0 and 1.7, surface area by nitrogen gas adsorption and surface microstructure by electron microscopy. Bioavailability from the iron powders, based on absolute iron intake, was significantly less than from FeSO4 (100%; P < 0.05) with the following rank order: Carbonyl (64%; Ferronyl, U.S.) > Electrolytic (54%; A-131, U.S.) > Electrolytic (46%; Electrolytic Iron, India) > H-Reduced (42%; AC-325, U.S.) > Reduced (24%; ATOMET 95SP, Canada) > CO-Reduced (21%; RSI-325, Sweden). Solubility testing of the iron powders resulted in different relative rankings and better RBV predictability with increasing time at pH 1.7 (R2 = 0.65 at 150 min). The prediction was improved with less time and lower pH (R2 = 0.82, pH 1.0 at 30 min). Surface area, ranging from 90 to 370 m2/kg, was also highly predictive of RBV (R2 = 0.80). Bioavailability of iron powders is less than bakery-grade ferrous sulfate and varies up to three times among different commercial forms. Solubility at pH 1.0 and surface area were predictive of iron bioavailability in rats.

Fullerenic structures and such structures tethered to carbon materials

DOEpatents

Goel, Anish; Howard, Jack B.; Vander Sande, John B.

2010-01-05

The fullerenic structures include fullerenes having molecular weights less than that of C.sub.60 with the exception of C.sub.36 and fullerenes having molecular weights greater than C.sub.60. Examples include fullerenes C.sub.50, C.sub.58, C.sub.130, and C.sub.176. Fullerenic structure chemically bonded to a carbon surface is also disclosed along with a method for tethering fullerenes to a carbon material. The method includes adding functionalized fullerene to a liquid suspension containing carbon material, drying the suspension to produce a powder, and heat treating the powder.

Fullerenic structures and such structures tethered to carbon materials

DOEpatents

Goel, Anish; Howard, Jack B.; Vander Sande, John B.

2012-10-09

The fullerenic structures include fullerenes having molecular weights less than that of C.sub.60 with the exception of C.sub.36 and fullerenes having molecular weights greater than C.sub.60. Examples include fullerenes C.sub.50, C.sub.58, C.sub.130, and C.sub.176. Fullerenic structure chemically bonded to a carbon surface is also disclosed along with a method for tethering fullerenes to a carbon material. The method includes adding functionalized fullerene to a liquid suspension containing carbon material, drying the suspension to produce a powder, and heat treating the powder.

Pilot Test of Hot Gas Decontamination of Explosives-Contaminated Equipment at Hawthorne Army Ammunition Plant (HWAAP), Hawthorne, Nevada. Appendices. Revision

DTIC Science & Technology

1990-06-01

was used to spike the following items of equipment: 0 powder boxes o steam-heated risers o steam-heated discharge valves o steel pipe o aluminum pipe...expose it to the internal surfaces. For pipe ( aluminum and steel), one end of the pipe section was covered with parafilm wax. Spike solution was added...spike the following items of equipment: "o powder box "o steam-heated riser "o steam-heated discharge valve "O steel pipe "o aluminum pipe Prior to

Preparing polymeric matrix composites using an aqueous slurry technique

NASA Technical Reports Server (NTRS)

Johnston, Norman J. (Inventor); Towell, Timothy W. (Inventor)

1993-01-01

An aqueous process was developed to prepare a consolidated composite laminate from an aqueous slurry. An aqueous poly(amic acid) surfactant solution was prepared by dissolving a poly(amic acid) powder in an aqueous ammonia solution. A polymeric powder was added to this solution to form a slurry. The slurry was deposited on carbon fiber to form a prepreg which was dried and stacked to form a composite laminate. The composite laminate was consolidated using pressure and was heated to form the polymeric matrix. The resulting composite laminate exhibited high fracture toughness and excellent consolidation.

METHOD OF PREPARING POLONIUM-BORON SOURCES

DOEpatents

Birden, J.H.

1959-08-01

An improved technique is described for preparation of a polonium-boron neutron source. A selected amount of Po-210 is vaporized into a thin walled nickel container, then the desired amcunt of boron powder is added. After sealing the container, it is heated quickly by induction heating to vaporize the Po-210 and deposit it in the still cool boron powder. The unit is then quickly cooled to prevent revaporization of the Po-210 from the boron. The build-up of neutron emission may be followed by means of a neutron counter in order to terminate the heating at the optimum level of neutron yield.

Effect of imaging powder and CAD/CAM stone types on the marginal gap of zirconia crowns.

PubMed

Alghazzawi, Tariq F; Al-Samadani, Khalid H; Lemons, Jack; Liu, Perng-Ru; Essig, Milton E; Bartolucci, Alfred A; Janowski, Gregg M

2015-02-01

To compare the marginal gap using different types of die stones and titanium dies with and without powders for imaging. A melamine tooth was prepared and scanned using a laboratory 3-shape scanner to mill a polyurethane die, which was duplicated into different stones (Jade, Lean, CEREC) and titanium. Each die was sprayed with imaging powders (NP, IPS, Optispray, Vita) to form 15 groups. Ten of each combination of stone/titanium and imaging powders were used to mill crowns. A light-bodied impression material was injected into the intaglio surface of each crown and placed on the corresponding die. Each crown was removed, and the monophase material was injected to form a monophase die, which was cut into 8 sections. Digital images were captured using a stereomicroscope to measure marginal gap. Scanning electron microscopy was used to determine the particle size and shape of imaging powders and stones. Marginal gaps ranged from mean (standard deviation) 49.32 to 1.20 micrometers (3.97-42.41 μm). There was no statistical difference (P > .05) in the marginal gap by any combination of stone/titanium and imaging powders. All of the imaging powders had a similar size and rounded shape, whereas the surface of the stones showed different structures. When a laboratory 3-shape scanner is used, all imaging powders performed the same for scanning titanium abutments. However, there was no added value related to the use of imaging powder on die stone. It is recommended that the selection of stone for a master cast be based on the hysical properties. When a laboratory 3-shape scanner is used, the imaging powder is not required for scanning die stone. Whenever scanning titanium implant abutments, select the least expensive imaging powder. Copyright © 2015 American Dental Association. Published by Elsevier Inc. All rights reserved.

Pozzolanic activity and durability of nano silica, micro silica and silica gel contained concrete

NASA Astrophysics Data System (ADS)

Al Ghabban, Ahmed; Al Zubaidi, Aseel B.; Fakhri, Zahraa

2018-05-01

This paper aims to investigate the influence of replacement of cement with nano silica, micro silica and silica gel admixtures on pozzolanic activity, the replacement ratio was10% for all admixture, silica gel used in two forms (beads and crushed powder). Also, the water absorption test was investigated for obtaining the durability properties of concrete, in specimens for this test admixtures were added in four different dosages 1%, 2%, 3% and 4% by weight of the cementitious material into the concrete mixture. Experimental investigations of modified concrete were conducted after 28 days of water curing. Results showed that mixes of nano silica and crushed silica gel showed a higher pozzolanic activity index. For the water absorption test, all mixes incorporating nano silica, micro silica and silica gel showed lower absorption than control mixes best result were noticed with crushed silica gel and nano silica mixes. DTA analysis confirms the results for both poisonous activity and water absorption.

Comparing activated carbon of different particle sizes on enhancing methane generation in upflow anaerobic digester.

PubMed

Xu, Suyun; He, Chuanqiu; Luo, Liwen; Lü, Fan; He, Pinjing; Cui, Lifeng

2015-11-01

Two sizes of conductive particles, i.e. 10-20 mesh granulated activated carbon (GAC) and 80-100 mesh powdered activated carbon (PAC) were added into lab-scale upflow anaerobic sludge blanket reactors, respectively, to testify their enhancement on the syntrophic metabolism of alcohols and volatile fatty acids (VFAs) in 95days operation. When OLR increased to more than 5.8gCOD/L/d, the differences between GAC/PAC supplemented reactors and the control reactor became more significant. The introduction of activated carbon could facilitate the enrichment of methanogens and accelerate the startup of methanogenesis, as indicated by enhanced methane yield and substrate degradation. High-throughput pyrosequencing analysis showed that syntrophic bacteria and Methanosarcina sp. with versatile metabolic capability increased in the tightly absorbed fraction on the PAC surface, leading to the promoted syntrophic associations. Thus PAC prevails over than GAC for methanogenic reactor with heavy load. Copyright © 2015 Elsevier Ltd. All rights reserved.

Preparation and catalytic activities of LaFeO3 and Fe2O3 for HMX thermal decomposition.

PubMed

Wei, Zhi-Xian; Xu, Yan-Qing; Liu, Hai-Yan; Hu, Chang-Wen

2009-06-15

Perovskite-type LaFeO(3) and alpha-Fe(2)O(3) with high specific surface areas were directly prepared with appropriate stearic acid-nitrates ratios by a novel stearic acid solution combustion method. The obtained powders were characterized by XRD, FT-IR and XPS techniques. The catalytic activities of perovskite-type LaFeO(3) and alpha-Fe(2)O(3) for the thermal decomposition of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) were investigated by TG and TG-EGA techniques. The experimental results show that the catalytic activity of perovskite-type LaFeO(3) was much higher than that of alpha-Fe(2)O(3) because of higher concentration of surface-adsorbed oxygen (O(ad)) and hydroxyl of LaFeO(3). The study points out a potential way to develop new and more active perovskite-type catalysts for the HMX thermal decomposition.

Preparation and enhanced daylight-induced photocatalytic activity of C,N,S-tridoped titanium dioxide powders.

PubMed

Zhou, Minghua; Yu, Jiaguo

2008-04-15

A simple method for preparing highly daylight-induced photoactive nanocrystalline C,N,S-tridoped TiO2 powders was developed by a solid-phase reaction. The as-prepared TiO2 powders were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectra, N2 adsorption-desorption measurements and transmission electron microscopy (TEM). The photocatalytic activity was evaluated by the photocatalytic oxidation of formaldehyde under daylight irradiation in air. The results show that daylight-induced photocatalytic activities of the as-prepared TiO2 powders were improved by C,N,S-tridoping. The C,N,S-tridoped TiO2 powders exhibited stronger absorption in the near UV and visible-light region with red shift in the band-gap transition. When the molar ratio of CS(NH2)2 to xerogel TiO2 powders (prepared by hydrolysis of Ti(OC4H9)4 in distilled water) (R) was kept in 3, the daylight-induced photocatalytic activities of the as-prepared C,N,S-tridoped TiO2 powders were about more than six times greater than that of Degussa P25 and un-doped TiO2 powders. The high activities of the C,N,S-tridoped TiO2 can be attributed to the results of the synergetic effects of strong absorption in the near UV and visible-light region, red shift in adsorption edge and two phase structures of un-doped TiO2 and C,N,S-tridoped TiO2.

Dry powder mixes comprising phase change materials

DOEpatents

Salyer, I.O.

1993-05-18

Free flowing, conformable powder-like mix of silica particles and a phase change material (p.c.m.) is disclosed. The silica particles have a critical size of about 7[times]10[sup [minus]3] to about 7[times]10[sup [minus]2] microns and the p.c.m. must be added to the silica in an amount of 80 wt. % or less p.c.m. per combined weight of silica and p.c.m. The powder-like mix can be used in tableware items, medical wraps, tree wraps, garments, quilts and blankets, and in cementitious compositions of the type in which it is beneficial to use a p.c.m. material. The silica-p.c.m. mix can also be admixed with soil to provide a soil warming effect and placed about a tree, flower, or shrub.

Structural and Electrical Properties of Lithium-Ion Rechargeable Battery Using the LiFePO4/Carbon Cathode Material.

PubMed

Kim, Young-Sung; Jeoung, Tae-Hoon; Nam, Sung-Pill; Lee, Seung-Hwan; Kim, Jea-Chul; Lee, Sung-Gap

2015-03-01

LiFePO4/C composite powder as cathode material and graphite powder as anode material for Li-ion batteries were synthesized by using the sol-gel method. An electrochemical improvement of LiFePO4 materials has been achieved by adding polyvinyl alcohol as a carbon source into as-prepared materials. The samples were characterized by elemental analysis (EA), X-ray diffraction (XRD), and field emission scanning electron microscopy (FE-EM). The chemical composition of LiFePO4/C powders was in a good agreement with that of the starting solution. The capacity loss after 500 cycles of LiFePO4/C cell is 11.1% in room temperature. These superior electrochemical properties show that LiFePO4/C composite materials are promising candidates as cathode materials.

Development of superalloys by powder metallurgy for use at 1000 - 1400 F

NASA Technical Reports Server (NTRS)

Calhoun, C. D.

1971-01-01

Consolidated powders of four nickel-base superalloys were studied for potential application as compressor and turbine discs in jet engines. All of the alloys were based on the Rene' 95 chemistry. Three of these had variations in carbon and A12O3 contents, and the fourth alloy was chemically modified to a higher volume fraction. The A12O3 was added by preoxidation of the powders prior to extrusion. Various levels of four experimental factors (1) alloy composition, (2) grain size, (3) thermomechanical processing, and (4) room temperature deformation plus final age were evaluated by tensile and stress rupture testing at 1200 F. Various levels of the four factors were assumed in order to construct the statistically-designed experiment, but the actual levels investigated were established in preliminary studies that preceded the statistical process development study.

Microstructure and properties of FeSiCr/PA6 composites by injection molding using FeSiCr powders by phosphating and coupling treatment

NASA Astrophysics Data System (ADS)

Wang, Lulu; Qiao, Liang; Zheng, Jingwu; Cai, Wei; Ying, Yao; Li, Wangchang; Che, Shenglei; Yu, Jing

2018-04-01

FeSiCr/PA6 composites were prepared by injection molding using the FeSiCr powders modified by different phosphating agents and KH550 coupling agent. The resistivity, impact strength, magnetic permeability and magnetic loss of the FeSiCr/PA6 composites were measured. The morphologies of different FeSiCr powders and the FeSiCr/PA6 composites were also observed by scanning electron microscope (SEM). The results showed that 1-Hydroxyethylidene-1,1-diphosphonic acid, phytic acid and H3PO4 could improve the electrical resistivity of FeSiCr powders by forming the dense phosphating layer except diphenylphosphinic acid. However, the resistivity of FeSiCr/PA6 composites using the FeSiCr powders treated by all the four phosphating agents had no obvious increase though the phosphating layer on the surface of FeSiCr powder came into being. The nylon insulation layer had much stronger influence than the phosphating layer on electrical resistivity of the composites. After adding appropriate KH550 coupling agent, the impact strengths of FeSiCr/PA6 composites were significantly improved, which may be associated with the tiny gap between FeSiCr powder and PA6 matrix. The effects of the phosphating agents on the magnetic permeability and loss of the FeSiCr/PA6 were small and the mechanism were also discussed.

16 CFR § 1209.35 - Product specification.

Code of Federal Regulations, 2013 CFR

2013-01-01

... and address of each chemical supplier. Where the chemical composition or formula of a commercially pre..., identifying the extent of impurities allowed. (3) The formulation of the fire-retardant chemicals added, including their chemical constituents and their form (for example, granulated, powdered, or liquid); the...

Ultraviolet Curable Powder Coatings with Robotic Curing for Aerospace Applications

DTIC Science & Technology

2012-05-01

millions of dollars annually on solvent- based coatings  Hexavalent chrome primer use still very widespread  Contains or requires volatile solvent...functionality can be added  Various advanced non- chrome corrosion inhibitors DISTRIBUTION A. Approved for public release; distribution unlimited. Case

Application of winter mushroom powder as an alternative to phosphates in emulsion-type sausages.

PubMed

Choe, Jeehwan; Lee, Juri; Jo, Kyung; Jo, Cheorun; Song, Minho; Jung, Samooel

2018-05-01

This research evaluated the utilization of winter mushrooms as a replacement for phosphate in emulsion-type sausages. Winter mushroom powder (WMP) was added to the sausages at 0, 0.5, 1.0, 1.5, and 2.0% (w/w), and phosphate was added at 0.3% as a positive control. The WMP additions above 1.0% increased the pH of meat batter and efficiently inhibited the exudation of fat from the sausages (p < 0.05). Lipid oxidation of sausages was inhibited by the addition of WMP (p < 0.05). On the other hand, the addition of phosphate and WMP provided different instrumental texture properties. However, no adverse effects were observed with respect to the color and sensory properties of the sausages containing WMP, except for that containing 2.0% WMP. Therefore, this research indicates that WMP can effectively replace phosphate in meat products, and that the most effective addition level may be 1.0% WMP. Copyright © 2018 Elsevier Ltd. All rights reserved.

Modified corrosion protection coatings for Concrete tower of Transmission line

NASA Astrophysics Data System (ADS)

Guo, Kai; Jing, Xiangyang; Wang, Hongli; Yue, Zengwu; Wu, Yaping; Mi, Xuchun; Li, Xingeng; Chen, Suhong; Fan, Zhibin

2017-12-01

By adding nano SiO2 particles, an enhanced K-PRTV anti-pollution flashover coating had been prepared. Optical profile meter (GT-K), atomic force microscopy (AFM) and infrared spectrometer (FT-IR) characterization were carried out on the coating surface analysis. With the use of modified epoxy resin as the base material, the supplemented by phosphate as a corrosion stabilizer, to achieve a corrosion of steel and galvanized steel with rust coating. Paint with excellent adhesion, more than 10MPa (1), resistant to neutral salt spray 1000h does not appear rust point. At the same time coating a large amount of ultra-fine zinc powder can be added for the tower galvanized layer zinc repair function, while the paint in the zinc powder for the tower to provide sacrificial anode protection, to achieve self-repair function of the coating. Compared to the market with a significant reduction in the cost of rust paint, enhance the anti-corrosion properties.

Effects of acid etching and adhesive treatments on host-derived cysteine cathepsin activity in dentin.

PubMed

Zhang, Wenhao; Yang, Weixiang; Wu, Shuyi; Zheng, Kaibin; Liao, Weili; Chen, Boli; Yao, Ke; Liang, Guobin; Li, Yan

2014-10-01

To analyze the effects of different processes during bonding on endogenous cysteine cathepsin activity in dentin. Dentin powder, prepared from extracted human third molars, was divided into 10 groups. Two lots of dentin powder were used to detect the effects of the procedure of protein extraction on endogenous cathepsin activity. The others were used to study effects of different acid-etching or adhesive treatments on enzyme activity. Concentrations of 37% phosphoric acid or 10% phosphoric acid, two etch-and-rinse adhesive systems, and two self-etching adhesive systems were used as dentin powder treatments. The untreated mineralized dentin powder was set as the control. After treatment, the proteins of each group were extracted. The total cathepsin activity in the extracts of each group was monitored with a fluorescence reader. In the control group, there were no significant differences in cathepsin activity between the protein extract before EDTA treatment and the protein extract after EDTA treatment (p > 0.05). The cathepsin activities of the three different extracts in the 37% phosphoric acid-treated group were different from each other (p < 0.05). The two acid-etching groups and two etch-and-rinse groups showed significant enzyme activity reduction vs the control group (p < 0.05). There were no significant differences between those four groups (p > 0.05). Treating the dentin powder with any of the two self-etching adhesives resulted in an increase in cathepsin activity (p < 0.05). The activity of cysteine cathepsins can be detected in dentin powder. Treatment with EDTA during protein extraction exerted an influence on cathepsin activity. Acid etching or etch-and-rinse adhesive systems may reduce the activity of endogenous cathepsins in dentin. Self-etching adhesive systems may increase the enzyme activity.

The recovery of polyphenols from olive mill waste using two adsorbing vegetable matrices.

PubMed

Ena, Alba; Pintucci, Cristina; Carlozzi, Pietro

2012-02-20

Olive mill wastewater (OMW) is considered one of the most pollutive waste materials in the Mediterranean basin. However, its phenolic fraction should be recovered, since it has been shown to have incredible benefits for health. In the present study, the adsorbent and desorbent capacities of Azolla and granular activated carbon (GAC) were investigated. The GAC was found to be more efficient than Azolla in both the adsorption and the desorption of phenols. The total characterization of two powder products obtained from Azolla and GAC desorption is reported, together with their antioxidant and antiradical activities. In the Azolla powder product, total polyphenols were more than twice as numerous as those found in the GAC powder product. The GAC powder contained hydroxytyrosol in concentrations that were 3.5 times higher than those of Azolla. On the other hand, both powder products showed great antiradical activities: the IC₅₀ was found to be 102 mg ml⁻¹ for the Azolla and 199 mg ml⁻¹ for the GAC powders respectively. The oxygen radical absorbance capacity was very high: 4097 μmol TE g⁻¹ Azolla powder product and 1277 μmol TE g⁻¹ of GAC powder products. Copyright © 2011 Elsevier B.V. All rights reserved.

Gentamicin Sulfate PEG-PLGA/PLGA-H Nanoparticles: Screening Design and Antimicrobial Effect Evaluation toward Clinic Bacterial Isolates

PubMed Central

Dorati, Rossella; DeTrizio, Antonella; Spalla, Melissa; Migliavacca, Roberta; Pagani, Laura; Pisani, Silvia; Chiesa, Enrica; Modena, Tiziana; Genta, Ida

2018-01-01

Nanotechnology is a promising approach both for restoring or enhancing activity of old and conventional antimicrobial agents and for treating intracellular infections by providing intracellular targeting and sustained release of drug inside infected cells. The present paper introduces a formulation study of gentamicin loaded biodegradable nanoparticles (Nps). Solid-oil-in water technique was studied for gentamicin sulfate nanoencapsulation using uncapped Polylactide-co-glycolide (PLGA-H) and Polylactide-co-glycolide-co-Polyethylenglycol (PLGA-PEG) blends. Screening design was applied to optimize: drug payload, Nps size and size distribution, stability and resuspendability after freeze-drying. PLGA-PEG concentration resulted most significant factor influencing particles size and drug content (DC): 8 w/w% DC and 200 nm Nps were obtained. Stirring rate resulted most influencing factor for size distribution (PDI): 700 rpm permitted to obtain homogeneous Nps dispersion (PDI = 1). Further experimental parameters investigated, by 23 screening design, were: polymer blend composition (PLGA-PEG and PLGA-H), Polyvinylalcohol (PVA) and methanol concentrations into aqueous phase. Drug content was increased to 10.5 w/w%. Nanoparticle lyophilization was studied adding cryoprotectants, polyvinypirrolidone K17 and K32, and sodiumcarboxymetylcellulose. Freeze-drying protocol was optimized by a mixture design. A freeze-dried Nps powder free resuspendable with stable Nps size and payload, was developed. The powder was tested on clinic bacterial isolates demonstrating that after encapsulation, gentamicin sulfate kept its activity. PMID:29329209

Remediation efficiency of three treatments on water polluted with endocrine disruptors: Assessment by means of in vitro techniques.

PubMed

Polloni-Silva, Juliana; Valdehita, Ana; Fracácio, Renata; Navas, José M

2017-04-01

Chemical substances with potential to disrupt endocrine systems have been detected in aquatic environments worldwide, making necessary the investigation about water treatments able to inhibit such potential. The present work aimed to assess the efficiency for removing endocrine disruptors (with estrogenic and androgenic activity) of three simple and inexpensive substrates that could be potentially used in sectors or regions with limited resources: powdered activated carbon (PAC), powdered natural zeolite (ZEO) (both at a concentration of 500 mg L -1 ) and natural aquatic humic substances (AHS) (at 30 mg L -1 ). MilliQ-water and mature water from fish facilities (aquarium water, AW), were artificially spiked with 17β-estradiol (E2), 17α-ethinylestradiol and dihydrotestosterone. Moreover, effluent samples from waste water treatment plants (WWTP) were also submitted to the remediation treatments. Estrogenic and androgenic activities were assessed with two cell lines permanently transfected with luciferase as reporter gene under the control of hormone receptors: AR-EcoScreen containing the human androgen receptor and HER-LUC transfected with the sea bass estrogen receptor. PAC was efficiently removing the estrogenic and androgenic compounds added to milliQ and AW. However, androgenic activity detected in WWTP effluents was only reduced after treatment with ZEO. The higher surface area of PAC could have facilitated the removal of spiked hormones in clean waters. However, it is possible that the substances responsible of the hormonal activity in WWTP have adsorbed to micro and nanoparticles present in suspension that would have been retained with higher efficiency by ZEO that show pores of several microns in size. Copyright © 2017 Elsevier Ltd. All rights reserved.

Elimination of Cu(II) toxicity by powdered waste sludge (PWS) addition to an activated sludge unit treating Cu(II) containing synthetic wastewater.

PubMed

Pamukoglu, M Yunus; Kargi, Fikret

2007-09-05

Copper(II) ion toxicity onto activated sludge organisms was eliminated by addition of powdered waste sludge (PWS) to the feed wastewater for removal of Cu(II) ions by biosorption before biological treatment. The synthetic feed wastewater containing 14 or 22 mgl(-1) Cu(II) was mixed with PWS in a mixing tank where Cu(II) ions were adsorbed onto PWS and the mixture was fed to a sedimentation tank to separate Cu(II) containing PWS from the feed wastewater. The activated sludge unit fed with the effluent of the sedimentation tank was operated at a hydraulic residence time (HRT) of 10h and sludge age (SRT) of 10 days. To investigate Cu(II), COD and toxicity removal performance of the activated sludge unit at different PWS loadings, the system was operated at different PWS loading rates (0.1-1 gPWSh(-1)) while the Cu(II) loading rate was constant throughout the operation. Percent copper, COD and toxicity removals increased with increasing PWS loading rate due to increased adsorption of Cu(II) onto PWS yielding low Cu(II) contents in the feed. Biomass concentration in the aeration tank increased and the sludge volume index (SVI) decreased with increasing PWS loading rate due to elimination of Cu(II) from the feed wastewater by PWS addition. PWS addition to the Cu(II) containing wastewater was proven to be effective for removal of Cu(II) by biosorption before biological treatment. Approximately, 1 gPWSh(-1) should be added for 28 mgCuh(-1) loading rate for complete removal of Cu(II) from the feed wastewater to obtain high COD removals in the activated sludge unit.

Synthesis of sea urchin-like carbon nanotubes on nano-diamond powder.

PubMed

Hwang, E J; Lee, S K; Jeong, M G; Lee, Y B; Lim, D S

2012-07-01

Carbon nanotubes (CNTs) have unique atomic structure and properties, such as a high aspect ratio and high mechanical, electrical and thermal properties. On the other hand, the agglomeration and entanglement of CNTs restrict their applications. Sea urchin-like multiwalled carbon nanotubes, which have a small aspect ratio, can minimize the problem of dispersion. The high hardness, thermal conductivity and chemical inertness of the nano-diamond powder make it suitable for a wide range of applications in the mechanical and electronic fields. CNTs were synthesized on nano-diamond powder by thermal CVD to fabricate a filler with suitable mechanical properties and chemical stability. This paper reports the growth of CNTs with a sea urchin-like structure on the surface of the nano-diamond powder. Nano-diamond powders were dispersed in an attritional milling system using zirconia beads in ethanol. After the milling process, 3-aminopropyltrimethoxysilane (APS) was added as a linker. Silanization was performed between the nano-diamond particles and the metal catalyst. Iron chloride was used as a catalyst for the fabrication of the CNTs. After drying, catalyst-attached nano-diamond powders could be achieved. The growth of the carbon nanotubes was carried out by CVD. The CNT morphology was examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The mean diameter and length of the CNTs were 201 nm and 3.25 microm, respectively.

Antifungal Effect of Henna against Candida albicans Adhered to Acrylic Resin as a Possible Method for Prevention of Denture Stomatitis

PubMed Central

Nawasrah, Amal; AlNimr, Amani; Ali, Aiman A.

2016-01-01

Denture stomatitis is a very common disease affecting the oral mucosa of denture wearers. The aim of this study was to measure the antifungal effect of henna against Candida albicans adhered to acrylic resin as a possible method for prevention of denture stomatitis. One-hundred-eighty acrylic plates were prepared of heat-cured acrylic denture resin. The specimens were divided into six groups of 30 samples each. The first group was only polymer and monomer following the conventional manufacturer instruction for processing complete dentures. The other five groups were processed by adding different concentration of Yamani henna powder (Harazi) to the polymer in a concentration of henna: polymer 1%, 2.5%, 5%, 7.5% and 10%, respectively. Samples were incubated in artificial saliva rich with Candida albicans at 37 °C, and the effect of henna on Candida albicans was evaluated in two different methods: semi-quantitative slide count and a culture-based quantitative assay (quantitative). Variation in the number of live Candida was observed with the increase in the concentration of Yamani henna powder. It was observed that the variation in live Candida, between control group and group B (concentration of Yamani henna powder was 1%), was statistically significant with a p-value of 0.0001. Similarly, variations in live Candida were significant, when the concentration of powder was 7.5% or 10% in contrast with control group and p-values were 0.0001 and 0.001 respectively. Adding henna to acrylic resin denture could be effective in controlling Candida albicans proliferation on the denture surface; however, its effects on the physical properties of acrylic resin denture need further studies. PMID:27223294

Supplementation of Citrus maxima Peel Powder Prevented Oxidative Stress, Fibrosis, and Hepatic Damage in Carbon Tetrachloride (CCl4) Treated Rats

PubMed Central

Chowdhury, Mohammed Riaz Hasan; Sagor, Md Abu Taher; Tabassum, Nabila; Potol, Md Abdullah

2015-01-01

Citrus maxima peel is rich in natural phenolic compounds and has a long use in the traditional medicine. HPLC-DAD analysis on Citrus maxima peel powder exhibited the presence of various phenolic compounds such as caffeic acid and (−)-epicatechin. To determine the plausible hepatoprotective activity of Citrus maxima peel powder, we used carbon tetrachloride (CCl4) treated rat model. Liver damage in rats was confirmed by measuring the AST, ALT, and ALP enzyme activities. In addition, lipid peroxidation products (MDA), nitric oxide, advanced protein oxidation products level (APOP), and catalase activities were also analyzed along with the histological profiling for the inflammatory cell infiltration, collagen, and iron deposition in liver. Dietary supplementation of Citrus maxima peel powder exhibited significant reduction of serum AST, ALT, and ALP activities in carbon tetrachloride treated rats. Moreover, Citrus maxima peel powder also showed a significant reduction of the oxidative stress markers (MDA, NO, and APOP level) and restored the catalase activity in CCl4 treated rats. Histological examination of the liver section revealed reduced inflammatory cells infiltration, collagen, and iron deposition in CCl4 treated rats. The results from this study demonstrated that Citrus maxima peel powder produced significant hepatoprotective action in CCl4 administered rats. PMID:26106435

Supplementation of Citrus maxima Peel Powder Prevented Oxidative Stress, Fibrosis, and Hepatic Damage in Carbon Tetrachloride (CCl4) Treated Rats.

PubMed

Chowdhury, Mohammed Riaz Hasan; Sagor, Md Abu Taher; Tabassum, Nabila; Potol, Md Abdullah; Hossain, Hemayet; Alam, Md Ashraful

2015-01-01

Citrus maxima peel is rich in natural phenolic compounds and has a long use in the traditional medicine. HPLC-DAD analysis on Citrus maxima peel powder exhibited the presence of various phenolic compounds such as caffeic acid and (-)-epicatechin. To determine the plausible hepatoprotective activity of Citrus maxima peel powder, we used carbon tetrachloride (CCl4) treated rat model. Liver damage in rats was confirmed by measuring the AST, ALT, and ALP enzyme activities. In addition, lipid peroxidation products (MDA), nitric oxide, advanced protein oxidation products level (APOP), and catalase activities were also analyzed along with the histological profiling for the inflammatory cell infiltration, collagen, and iron deposition in liver. Dietary supplementation of Citrus maxima peel powder exhibited significant reduction of serum AST, ALT, and ALP activities in carbon tetrachloride treated rats. Moreover, Citrus maxima peel powder also showed a significant reduction of the oxidative stress markers (MDA, NO, and APOP level) and restored the catalase activity in CCl4 treated rats. Histological examination of the liver section revealed reduced inflammatory cells infiltration, collagen, and iron deposition in CCl4 treated rats. The results from this study demonstrated that Citrus maxima peel powder produced significant hepatoprotective action in CCl4 administered rats.

Estimates of increased black carbon emissions from electrostatic precipitators during powdered activated carbon injection for mercury emissions control.

PubMed

Clack, Herek L

2012-07-03

The behavior of mercury sorbents within electrostatic precipitators (ESPs) is not well-understood, despite a decade or more of full-scale testing. Recent laboratory results suggest that powdered activated carbon exhibits somewhat different collection behavior than fly ash in an ESP and particulate filters located at the outlet of ESPs have shown evidence of powdered activated carbon penetration during full-scale tests of sorbent injection for mercury emissions control. The present analysis considers a range of assumed differential ESP collection efficiencies for powdered activated carbon as compared to fly ash. Estimated emission rates of submicrometer powdered activated carbon are compared to estimated emission rates of particulate carbon on submicrometer fly ash, each corresponding to its respective collection efficiency. To the extent that any emitted powdered activated carbon exhibits size and optical characteristics similar to black carbon, such emissions could effectively constitute an increase in black carbon emissions from coal-based stationary power generation. The results reveal that even for the low injection rates associated with chemically impregnated carbons, submicrometer particulate carbon emissions can easily double if the submicrometer fraction of the native fly ash has a low carbon content. Increasing sorbent injection rates, larger collection efficiency differentials as compared to fly ash, and decreasing sorbent particle size all lead to increases in the estimated submicrometer particulate carbon emissions.

21 CFR 520.44 - Acetazolamide sodium soluble powder.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Acetazolamide sodium soluble powder. 520.44... Acetazolamide sodium soluble powder. (a) Specifications. The drug is in a powder form containing acetazolamide sodium, USP equivalent to 25 percent acetazolamide activity. (b) Sponsor. See No. 053501 in § 510.600(c...

21 CFR 520.44 - Acetazolamide sodium soluble powder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acetazolamide sodium soluble powder. 520.44... Acetazolamide sodium soluble powder. (a) Specifications. The drug is in a powder form containing acetazolamide sodium, USP equivalent to 25 percent acetazolamide activity. (b) Sponsor. See No. 053501 in § 510.600(c...

21 CFR 520.44 - Acetazolamide sodium soluble powder.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Acetazolamide sodium soluble powder. 520.44... Acetazolamide sodium soluble powder. (a) Specifications. The drug is in a powder form containing acetazolamide sodium, USP equivalent to 25 percent acetazolamide activity. (b) Sponsor. See No. 053501 in § 510.600(c...

Human beta-glucuronidase. Measurement of its activity in gallbladder bile devoid of intrinsic interference.

PubMed

Ho, Y C; Ho, K J

1988-04-01

Our purpose is to develop a standard method for preparing the bile for beta-glucuronidase determination by removal of bile acids and conjugated bilirubin which interfere with its activity. The bile acids and conjugated bilirubin in their purified solutions and in the diluted gallbladder biles could be extracted completely with cholestyramine in powder form or tetrahexylammonium chloride (THAC) in chloroform or ethyl acetate. The enzyme was, however, partially precipitated with cholestyramine and denatured by chloroform but not by ethyl acetate. A standard procedure, therefore, includes extraction of the diluted gallbladder bile with THAC in ethyl acetate, followed by determination of the maximal velocity (Vmax) of the enzyme by a kinetic method employing phenolphthalein glucuronide as the substrate. The average Vmax of beta-glucuronidase in the 20 normal gallbladder biles was 165 +/- 86 nmol/min/ml (mean +/- SD), a 23.5-fold increase over the activity before extraction. The measured activity represented the true activity of the enzyme in the bile for recovery of activity of the enzyme added to the bile was practically complete.

Neuroprotective effects of the antiparkinson drug Mucuna pruriens.

PubMed

Manyam, Bala V; Dhanasekaran, Muralikrishnan; Hare, Theodore A

2004-09-01

Mucuna pruriens possesses significantly higher antiparkinson activity compared with levodopa in the 6-hydroxydopamine (6-OHDA) lesioned rat model of Parkinson's disease. The present study evaluated the neurorestorative effect of Mucuna pruriens cotyledon powder on the nigrostriatal tract of 6-OHDA lesioned rats. Mucuna pruriens cotyledon powder significantly increased the brain mitochondrial complex-I activity but did not affect the total monoamine oxidase activity (in vitro). Unlike synthetic levodopa treatment, Mucuna pruriens cotyledon powder treatment significantly restored the endogenous levodopa, dopamine, norepinephrine and serotonin content in the substantia nigra. Nicotine adenine dinucleotide (NADH) and coenzyme Q-10, that are shown to have a therapeutic benefit in Parkinson's disease, were present in the Mucuna pruriens cotyledon powder. Earlier studies showed that Mucuna pruriens treatment controls the symptoms of Parkinson's disease. This additional finding of a neurorestorative benefit by Mucuna pruriens cotyledon powder on the degenerating dopaminergic neurons in the substantia nigra may be due to increased complex-I activity and the presence of NADH and coenzyme Q-10. Copyright (c) 2004 John Wiley & Sons, Ltd.

Lead recovery and glass microspheres synthesis from waste CRT funnel glasses through carbon thermal reduction enhanced acid leaching process.

PubMed

Mingfei, Xing; Yaping, Wang; Jun, Li; Hua, Xu

2016-03-15

In this study, a novel process for detoxification and reutilization of waste cathode ray tube (CRT) funnel glass was developed by carbon thermal reduction enhanced acid leaching process. The key to this process is removal of lead from the CRT funnel glass and synchronous preparation of glass microspheres. Carbon powder was used as an isolation agent and a reducing agent. Under the isolation of the carbon powder, the funnel glass powder was sintered into glass microspheres. In thermal reduction, PbO in the funnel glass was first reduced to elemental Pb by carbon monoxide and then located on the surface of glass microspheres which can be removed easily by acid leaching. Experimental results showed that temperature, carbon adding amount and holding time were the major parameters that controlled lead removal rate. The maximum lead removal rate was 94.80% and glass microspheres that measured 0.73-14.74μm were obtained successfully by setting the temperature, carbon adding amount and holding time at 1200°C, 10% and 30min, respectively. The prepared glass microspheres may be used as fillers in polymer materials and abrasive materials, among others. Accordingly, this study proposed a practical and economical process for detoxification and recycling of waste lead-containing glass. Copyright © 2015 Elsevier B.V. All rights reserved.

Alleviative effects of litchi (Litchi chinensis Sonn.) flower on lipid peroxidation and protein degradation in emulsified pork meatballs.

PubMed

Ding, Yi; Wang, Sheng-Yao; Yang, Deng-Jye; Chang, Ming-Hsu; Chen, Yi-Chen

2015-09-01

To avoid or retard the lipid peroxidation of meat products, antioxidants are commonly added. Considering the safety and health of additives in meat products, consumers prefer natural antioxidants rather than synthetic ones. Gentisic acid and epicatechin were identified as the major phenolic acid and flavonoid, respectively, of litchi flowers (LFs). The physicochemical properties of pork meatballs with or without dried LF powders (0.5%, 1.0%, and 1.5%, w/w) and tert-butylhydroquinone (TBHQ; 0.01%, w/w) were analyzed during a 4-week frozen storage period. LF and TBHQ decreased (p < 0.05) thiobarbituric acid reactive substance (TBARS) values but increased (p < 0.05) thiol group contents in meatballs. LF added to meatballs improved (p < 0.05) texture and water-holding capacity (centrifugation/purge losses) more than in the control group upon the storage. Although LF powders made meatballs redder and darker (p < 0.05) than the control and TBHQ groups, they did not affect the preference of panelists. The addition of 0.5% LF powders exhibited the best (p < 0.05) overall sensory panel acceptance. LFs may be an effective natural antioxidant to reduce lipid and protein oxidation for frozen cooked meat products. Copyright © 2015. Published by Elsevier B.V.

Spectrophotometric determination of boric acid in boron powder with curcumin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grotheer, E.W.

1979-12-01

A rapid and accurate method was needed to determine trace amounts of boric acid for quality control and specification testing of elemental boron. The reaction between boric acid and curcumin occurs at a measurable rate only when the curcumin molecule is protonated. Protonation takes place at the carbonyl groups in the presence of a strong acid and occurs completely and rapidly when sulfuric acid is added to a solution of curcumin in acetic acid. Spectrophotometric measurements were made. The extraction of boric acid from boron powder was found to be complete within 2h when either water or the diol solutionmore » was used. Whatman No. 40 cr 42 filter paper was used to obtain diol samples free of boron particles. The extraction efficiency of 2-ethyl-1,3-hexanediol was evaluated by adding 1 ml of 500 ppM aqueous boric acid and 1 drop of 10% NaOH to accurately weighed samples of boron powder. The water then was evaporated at room temperature and the samples were extracted with diol solution. The data obtained are included. The extraction efficiency also was evaluated by determining the boric acid content of boron which had been recovered from a previous extraction and boric acid determination. The determination of boric acid using curcumin is unaffected by the presence of other compounds, except for fluoride and nitrate ions. 2 tables. (DP)« less

Sonocatalytic degradation of azo fuchsine in the presence of the Co-doped and Cr-doped mixed crystal TiO2 powders and comparison of their sonocatalytic activities.

PubMed

Wang, Jun; Lv, Yanhui; Zhang, Zhaohong; Deng, Yingqiao; Zhang, Liquan; Liu, Bin; Xu, Rui; Zhang, Xiangdong

2009-10-15

In order to degrade some pollutants effectively under ultrasonic irradiation, the Co-doped and Cr-doped mixed crystal TiO(2) powders, with high sonocatalytic activity, were prepared as sonocatalyst. The Co-doped and Cr-doped mixed crystal TiO(2) powders as sonocatalyst were prepared through sol-gel and heat-treated methods from tetrabutylorthotitanate, and then were characterized by XRD and TG-DTA technologies. In order to compare and evaluate the sonocatalytic activity of the Co-doped and Cr-doped mixed crystal TiO(2) powders, the low power ultrasound was as an irradiation source and the azo fuchsine was chosen as a model compound to be degraded. The degradation process was investigated by UV-vis, TOC, ion chromatogram and HPLC techniques. The results indicated that the sonocatalytic activity of Cr-doped mixed crystal TiO(2) powder was higher than that of Co-doped and undoped mixed crystal TiO(2) powder during the sonocatalytic degradation of the azo fuchsine in aqueous solution. These results may be of great significance for driving sonocatalytic method to treat non- or low-transparent industrial wastewaters.

In vitro antioxidant and cholinesterase inhibitory activities of Elatostema papillosum leaves and correlation with their phytochemical profiles: a study relevant to the treatment of Alzheimer's disease.

PubMed

Ali Reza, A S M; Hossain, Mohammad Shahadat; Akhter, Sharmin; Rahman, Md Rezanur; Nasrin, Mst Samima; Uddin, Md Josim; Sadik, Golam; Khurshid Alam, A H M

2018-04-05

Alzheimer's disease (AD), one of the major causes of dementia, is an overwhelming neurodegenerative disease that particularly affects the brain, leading to memory loss and impairment of language and judgment capacity. The aim of the present study was to investigate the antioxidant and anticholinesterase properties of the leaves of Elatostema papillosum (EPL) and correlate with their phytochemical profiles, which are relevant to the treatment of AD. The dried coarse powder of EPL was extracted with 80% methanol (EPL-M80) by cold extraction method. The resultant EPL-M80 was assessed for acetylcholinesterase (AChE) and butyrylcholinesterase (BChE) inhibitory activity by the Ellman method. The antioxidant activity was determined by DPPH (1, 1-diphenyl-2-picrylhydrazyl) and hydroxyl radical scavenging assays. Quantitative phytochemical (phenolic and flavonoid contents) analysis of endogenous substances in EPL-M80 was performed by standard spectrophotometric methods. EPL-M80 significantly (p < 0.05) inhibited AChE and BChE activity with IC 50 of 165.40 ± 4.01 and 213.81 ± 3.57 μg/mL, respectively in a dose-dependent manner. Additionally, EPL-M80 exhibited strong radical scavenging activity against DPPH (IC 50 = 32.35 ± 0.68 μg/mL) and hydroxyl radical (IC 50 = 19.67 ± 1.42 μg/mL) when compared to that of standards. EPL-M80 was found to be rich in phenolic (23.74 mg gallic acid equivalent/g of dry extract) and flavonoid (31.18 mg quercetin equivalent/g of dry extract) content. Furthermore, a positive correlation (p < 0.001) was observed between the total phenolics and antioxidant as well as the anticholinesterase potential. The marked inhibition of AChE and BChE, and potent antioxidant activity of the leaves of Elatostema papillosum highlight its potential to provide an effective treatment for AD.

Physicochemical and sensory characteristics of fat-free goat milk yogurt with added stabilizers and skim milk powder fortification.

PubMed

Bruzantin, F P; Daniel, J L P; da Silva, P P M; Spoto, M H F

2016-05-01

Goat milk yogurt has a less consistent coagulum compared with cow milk yogurt; furthermore, the presence of goat milk in foodstuffs imparts a characteristic flavor that can restrict its acceptance by consumers. This study aimed to assess and compare the physicochemical and sensory characteristics of fat-free goat milk yogurts with added stabilizers or bovine skim milk powder to improve the final product. Four treatment additions were evaluated: (1) a mixture of 0.1% (wt/vol) carrageenan and 0.1% (wt/vol) pectin (treatment CR); (2) 0.5% (wt/vol) pectin (treatment PE); (3) 4.65% (wt/vol) bovine skim milk powder (treatment BM); and (4) control (no stabilizer; treatment CT). The physicochemical parameters were investigated at on d 1 and 5 of storage. The BM treatment presented higher pH and titratable acidity values, resulting in a buffering capacity effect. The total crude protein (CP) and solids-not-fat (SNF) contents were also higher in BM compared with the other evaluated treatments because of the addition of bovine skim milk powder. We detected a reduction in pH values for all treatments. Lower SNF contents were present in the CR and CT treatments, which might be related to a syneresis process during storage; moreover, an increase in total CP was observed for all treatments due to the proteolytic action of the starter culture. Sensory attributes, including appearance (color, consistency, and presence of lumps), texture (consistency, viscosity, and presence of lumps), flavor (bitter, sweet, and characteristic of commercial plain nonfat yogurt), and overall impression were evaluated by quantitative descriptive analysis. The addition of 0.5% (wt/vol) of pectin (PE treatment) strengthened the curd; however, the visual and oral presence of lumps and a higher bitterness score were noted by trained panelists, which resulted in the lowest overall impression score for the PE treatment. In several sensory attributes, the CR treatment was considered similar to the control; the mixture of 0.1% (wt/vol) carrageenan and 0.1% (wt/vol) pectin was not as effective as expected. Goat milk yogurt containing added bovine skim milk powder (BM) had improved consistency, viscosity, and flavor due to its higher SNF and total CP contents, which are particularly important for the desirable texture of plain nonfat yogurt. In addition, the BM yogurt was considered to have characteristics most similar to that of available commercial brands and achieved the best score for overall impression. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effect of additional of Hoodia Gordonii and seaweed powder on the sensory and physicochemical properties of brown rice bar

NASA Astrophysics Data System (ADS)

Hajal, Masturah Ebni; Ghani, Maaruf Abd; Daud, Norlida Mat

2015-09-01

Awareness of the nutritional content of food has increased with the emergence of various health products in the market. Cereal bar is one of the beneficial foods among consumer that concern on their healthy food. This study was conducted to develop a brown rice bar that contain active ingredients (H. gordonii and seaweed powder) and to determine the effect on sensory evaluation and physicochemical properties (colour, texture and proximate analysis) of this product. This study consisted of two phases in which the first phase consisted of development of ten formulations including control. All of the formulations were undergo analysis of colour, texture and sensory evaluation. Based on the sensory evaluation, Control (H. gordonii: 0%, seaweed: 0%) and two best formulations that consist of formulation 6 (H. gordonii: 1.6%; seaweed: 2.8%) and formulation 9 (H. gordonii: 2.4%, seaweed: 2.8%) were chosen to undergo the second phase which is proximate analysis. Base on the result, were significant different (p<0.05) on proximate analysis except for the protein and moisture content. Therefore, it can be concluded that H. gordonii is a good source of fiber when adding in a bar.

Operando Synchrotron X-ray Powder Diffraction and Modulated-Excitation Infrared Spectroscopy Elucidate the CO2 Promotion on a Commercial Methanol Synthesis Catalyst.

PubMed

Martin, Oliver; Mondelli, Cecilia; Cervellino, Antonio; Ferri, Davide; Curulla-Ferré, Daniel; Pérez-Ramírez, Javier

2016-09-05

Optimal amounts of CO2 are added to syngas to boost the methanol synthesis rate on Cu-ZnO-Al2 O3 in the industrial process. The reason for CO2 promotion is not sufficiently understood at the particle level due to the catalyst complexity and the high demands of characterization under true reaction conditions. Herein, we applied operando synchrotron X-ray powder diffraction and modulated-excitation infrared spectroscopy on a commercial catalyst to gain insights into its morphology and surface chemistry. These studies unveiled that Cu and ZnO agglomerate and ZnO particles flatten under CO/H2 and/or CO2 /H2 . Under the optimal CO/CO2 /H2 mixture, sintering is prevented and ZnO crystals adopt an elongated shape due to the minimal presence of the H2 O byproduct, enhancing the water-gas shift activity and thus the methanol production. Our results provide a rationale to the CO2 promotion emphasizing the importance of advanced analytical methods to establish structure-performance relations in heterogeneous catalysis. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation of extrusions of bulk mixed oxide compounds with high macroporosity and mechanical strength

DOEpatents

Flytzani-Stephanopoulos, Maria; Jothimurugesan, Kandaswami

1990-01-01

A simple and effective method for producing bulk single and mixed oxide absorbents and catalysts is disclosed. The method yields bulk single oxide and mixed oxide absorbent and catalyst materials which combine a high macroporosity with relatively high surface area and good mechanical strength. The materials are prepared in a pellet form using as starting compounds, calcined powders of the desired composition and physical properties these powders are crushed to broad particle size distribution, and, optionally may be combined with an inorganic clay binder. The necessary amount of water is added to form a paste which is extruded, dried and heat treated to yield and desired extrudate strength. The physical properties of the extruded materials (density, macroporosity and surface area) are substantially the same as the constituent powder is the temperature of the heat treatment of the extrudates is approximately the same as the calcination temperature of the powder. If the former is substantially higher than the latter, the surface area decreases, but the macroporosity of the extrusions remains essentially constant.

Effects of oral powder electrolyte administration on packed cell volume, plasma chemistry parameters, and incidence of colic in horses participating in a 6-day 162-km trail ride

PubMed Central

Walker, Wade T.; Callan, Robert J.; Hill, Ashley E.; Tisher, Kelly B.

2014-01-01

This study evaluated the effects of administering oral powder electrolytes on packed cell volume (PCV), plasma chemistry parameters, and incidence of colic in horses participating on a 6-day 162-km trail ride in which water was not offered ad libitum. Twenty-three horses received grain with powder electrolytes daily while 19 control horses received grain only. Horses were ridden approximately 32 km a day at a walk or trot. Packed cell volume and plasma chemistry parameters were analyzed daily. Episodes of colic were diagnosed and treated by a veterinarian unaware of treatment group allocation. Blood parameters and incidence of colic were compared between treatment groups. Electrolyte administration did not alter PCV or plasma chemistry parameters compared to controls. The incidence of colic was significantly higher in treated horses (P = 0.05). Oral powder electrolytes did not enhance hydration status or electrolyte homeostasis and may be associated with colic in horses participating on long distance trail rides similar to this model. PMID:25082992

Formation of apatitic calcium phosphates in a Na-K-phosphate solution of pH 7.4.

PubMed

Tas, A C; Aldinger, F

2005-02-01

Poorly crystalline, apatitic calcium phosphate powders have been synthesized by slowly adding a Na- and K-containing reference phosphate solution with a pH value of 7.4 to an aqueous calcium nitrate solution at 37 degrees C. Nano-particulated apatitic powders obtained were shown to contain small amounts of Na and K, which render them more similar in chemical composition to that of the bone mineral. Precipitated and dried powders were found to exhibit self-hardening cement properties when kneaded in a mortar with a sodium citrate- and sodium phosphate-containing starter solution. The same phosphate solution used in powder synthesis was found to be able to partially convert natural, white and translucent marble pieces of calcite (CaCO3) into calcium-deficient hydroxyapatite upon aging the samples in that solution for 3 days at 60 degrees C. Sample characterization was performed by using scanning electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, inductively-coupled plasma atomic emission spectroscopy, and simultaneous thermogravimetry and differential thermal analysis.

Effects of oral powder electrolyte administration on packed cell volume, plasma chemistry parameters, and incidence of colic in horses participating in a 6-day 162-km trail ride.

PubMed

Walker, Wade T; Callan, Robert J; Hill, Ashley E; Tisher, Kelly B

2014-08-01

This study evaluated the effects of administering oral powder electrolytes on packed cell volume (PCV), plasma chemistry parameters, and incidence of colic in horses participating on a 6-day 162-km trail ride in which water was not offered ad libitum. Twenty-three horses received grain with powder electrolytes daily while 19 control horses received grain only. Horses were ridden approximately 32 km a day at a walk or trot. Packed cell volume and plasma chemistry parameters were analyzed daily. Episodes of colic were diagnosed and treated by a veterinarian unaware of treatment group allocation. Blood parameters and incidence of colic were compared between treatment groups. Electrolyte administration did not alter PCV or plasma chemistry parameters compared to controls. The incidence of colic was significantly higher in treated horses (P = 0.05). Oral powder electrolytes did not enhance hydration status or electrolyte homeostasis and may be associated with colic in horses participating on long distance trail rides similar to this model.

Comparing Strengthening Mechanisms of Vapor Grown Carbon Fiber vs. Titanium Carbide Reinforced Powder Metallurgy Titanium Metal Matrix Composites

NASA Astrophysics Data System (ADS)

Franco, Staub; Kondoh, Katsuyoshi; Umeda, Junko; Imai, Hisashi

In this experiment, TILOP-45 commercially pure titanium powder was mixed with vapor grown carbon fibers (VGCF) to form a 200 g 0.5 wt. % VGCF solution. After adding 0.15 grams of cle-safe oil, a rocking mill shook the sample at 60.0 Hz for 2 hours, resulting in satisfactory dispersion of VGCF on the titanium powder surface. The powder solution was compacted by spark plasma sintering (SPS) and hot extruded. The SPS temperature was set to either 800 °C or 1,000 °C and the pressure to 35 kN. Using an extrusion ratio of 13:1 and ram speed of 3 mm/s, the titanium billet, preheated to either 800 °C or 1,000 °C, was deformed to a 10 mm diameter rod. All four permutations of SPS and extrusion temperatures were tested. Microstructure, grain size, hardness, and oxygen/nitrogen/carbon content were observed. Also, a UTS experiment was done followed by SEM observations of the fractured surfaces.

Thermogravimetric feasibility study of argon purification using powders of titanium alloys with molybdenum and vanadium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eremeev, A.P.; Veselovskii, P.F.

1987-10-20

The high adsorption and chemical activity of titanium alloy powders (TiMo > TiV) having specific size and chemical compositions, and the nature of the surface and its specific energy characteristics permit one to use them effectively for the purification of argon and other inert gases from impurities such as water vapor, carbon dioxide gas, oxygen, and nitrogen. In agreement with the developed activity series the irreversible adsorption of impurities (1 vol. %) by the indicated powders can be controlled using powders or filters pressed from these powders by heating to temperatures of 500-700/sup 0/. The thickness of the filters canmore » be established on the basis of the rate constants of the chemical reactions of the impurities with the TiMo and TiV powders obtained in this study.« less

Relevance of the setting reaction to the injectability of tricalcium phosphate pastes.

PubMed

Montufar, E B; Maazouz, Y; Ginebra, M P

2013-04-01

The aim of the present work was to analyze the influence of the setting reaction on the injectability of tricalcium phosphate (TCP) pastes. Even if the injection was performed early after mixing powder and liquid, powder reactivity was shown to play a significant role in the injectability of TCP pastes. Significant differences were observed between the injection behavior of non-hardening β-TCP pastes and that of self-hardening α-TCP pastes. The differences were more marked at low liquid-to-powder ratios, using fine powders and injecting through thin needles. α-TCP was, in general, less injectable than β-TCP and required higher injection loads. Moreover, clogging was identified as a mechanism hindering or even preventing injectability, different and clearly distinguishable from the filter-pressing phenomenon. α-TCP pastes presented transient clogging episodes, which were not observed in β-TCP pastes with equivalent particle size distribution. Different parameters affecting powder reactivity were also shown to affect paste injectability. Thus, whereas powder calcination resulted in an increased injectability due to lower particle reactivity, the addition of setting accelerants, such as hydroxyapatite nanoparticles, tended to reduce the injectability of the TCP pastes, especially if adjoined simultaneously with a Na2HPO4 solution. Although, as a general trend, faster-setting pastes were less injectable, some exceptions to this rule were found. For example, whereas in the absence of setting accelerants fine TCP powders were more injectable than the coarse ones, in spite of their shorter setting times, this trend was inverted when setting accelerants were added, and coarse powders were more injectable than the fine ones. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Vancomycin Powder Regimen for Prevention of Surgical Site Infection in Complex Spine Surgeries.

PubMed

Van Hal, Michael; Lee, Joon; Laudermilch, Dann; Nwasike, Chinedu; Kang, James

2017-10-01

In total, 496 patients of a single surgeon cohort examining the surgical-site infection (SSI) rates with the addition of vancomycin powder in both diabetic and revision spine surgery cases. A historical control group of 652 patients were compared from the same surgeon over an earlier time period before the inception of using vancomycin powder prophylaxis. The objective of this study was to describe and compare the rates of infection in high-risk patient populations while using vancomycin powder. Vancomycin powder may not decrease an already low rate of infection. Therefore, use of vancomycin powder in high-risk patients with a higher rate of infection would potentially show benefit of vancomycin powder. In total, 496 patient charts were collected from a database of cases. Patients were included in the cohort if they had revision spinal operation or if they were diabetic. Patients in the time period July 2010 to August 2013 were included in the vancomycin protocol where 1 g of vancomycin powder was added to the wound before wound closure. Cases were considered positive if there was a positive culture or if there was sufficient clinical suspicion to treat. As a control to this cohort, 692 charts were reviewed from a earlier time period of the same surgeon and institution. In total, 28 patients of 496 (5.6%) patients in the cohort returned to the operating room for seroma, hematoma, draining wound, or infection. Sixteen of these patients (16/496, 3.2%) had a culture positive infection or were treated as an infection. This rate was significantly lower than the historical rate before the protocol. Although vancomycin does seem to be useful in decreasing SSIs, it is not a panacea. SSIs in high-risk patients were not completely eliminated by the vancomycin protocol.

PERFORMANCE OF ACTIVATED SLUDGE-POWDERED ACTIVATED CARBON-WET AIR REGENERATION SYSTEMS

EPA Science Inventory

The investigation summarized in the report was undertaken to evaluate the performance of powdered activated carbon (PAC) technology used in conjunction with wet air regeneration (WAR) at municipal wastewater treatment plants. Excessive ash concentrations accumulated in the mixed ...

Study of soft magnetic iron cobalt based alloys processed by powder injection molding

NASA Astrophysics Data System (ADS)

Silva, Aline; Lozano, Jaime A.; Machado, Ricardo; Escobar, Jairo A.; Wendhausen, Paulo A. P.

As a near net shape process, powder injection molding (PIM) opens new possibilities to process Fe-Co alloys for magnetic applications. Due to the fact that PIM does not involve plastic deformation of the material during processing, we envisioned the possibility of eliminating vanadium (V), which is generally added to Fe-Co alloys to improve the ductility in order to enable its further shaping by conventional processes such as forging and cold rolling. In our investigation we have found out two main futures related to the elimination of V, which lead to a cost-benefit gain in manufacturing small magnetic components where high-saturation induction is needed at low frequencies. Firstly, the elimination of V enables the achievement of much better magnetic properties when alloys are processed by PIM. Secondly, a lower sintering temperature can be used when the alloy is processed starting with elemental Fe and Co powders without the addition of V.

Stabilized Alumina/Ethanol Colloidal Dispersion for Seeding High Temperature Air Flows

NASA Technical Reports Server (NTRS)

Wernet, Judith H.; Wernet, Mark P.

1994-01-01

Seeding air flows with particles to enable measurements of gas velocities via laser anemometry and/or particle image velocimetry techniques can be quite exasperating. The seeding requirements are compounded when high temperature environments are encountered and special care must be used in selecting a refractory seed material. The pH stabilization techniques commonly employed in ceramic processing are used to obtain stable dispersions for generating aerosols of refractory seed material. By adding submicron alumina particles to a preadjusted pH solution of ethanol, a stable dispersion is obtained which when atomized produces a high quality aerosol. Commercial grade alumina powder is used with a moderate size distribution. The technique is not limited to alumina/ethanol and is also demonstrated with an alumina/H2O system. Other ceramic powders in various polar solvents could also be used once the point of zero charge (pH(sub pzc)) of the powder in the solvent has been determined.

Color stabilization of porcine hemoglobin during spray-drying and powder storage by combining chelating and reducing agents.

PubMed

Salvador, P; Toldrà, M; Parés, D; Carretero, C; Saguer, E

2009-10-01

This work focuses on the effects of adding a chelating agent - such as nicotinic acid (NA, 2% w/v) or nicotinamide (Nam, 2.5% w/v) - along with glucose as a reducing agent (G, 10% w/v) to fresh porcine hemoglobin in order to stabilize its red color during spray-drying and powder storage at room temperature. Correlations between the CIELAB color parameters and the relative percentages of the different hemoglobin derivatives (liganded and deliganded ferrohemoglobin, and methemoglobin) were analyzed. The results indicate that, although little effects could be observed for any of the combined treatments on fresh hemoglobin, they were effective against pigment autoxidation during dehydration and subsequent storage. From the results, it can also be concluded that glucose was the main contributor to the color stabilization of the hemoglobin powder, probably due to its high water retention capacity.

Research on self-propagating high temperature synthesis prepared ZrC-ZrB2 composite ceramic

NASA Astrophysics Data System (ADS)

Yong, Cheng; Xunjia, Su; Genliang, Hou; YaKun, Xing

2013-03-01

ZrC-ZrB2 composite ceramic material is prepared by self-propagating high temperature synthesis, using Zr powders, CrO2 powders and Al powders as raw materials. Samples are studied by XRD and SEM, the results show that: ZrC-ZrB2 composite ceramic is attained after self-propagating high-temperature reaction, with Zr+ B4C as the main reactive system, and which is added respectively different content (CrO3 + Al) system. The study finds that the ceramic composite products are mainly composed of ZrC and ZrB2 phase, and other subphase. Compared to the main reactive system composite ceramic, composite ceramic grains grow up obviously, after introduction of the highly exothermic system (CrO3 + Al) in the main reactive system, and with the gradual increase of the content (CrO3 + Al).

Properties of concrete containing coconut shell powder (CSP) as a filler

NASA Astrophysics Data System (ADS)

Leman, A. S.; Shahidan, S.; Nasir, A. J.; Senin, M. S.; Zuki, S. S. Mohd; Ibrahim, M. H. Wan; Deraman, R.; Khalid, F. S.; Azhar, A. T. S.

2017-11-01

Coconut shellsare a type of agricultural waste which can be converted into useful material. Therefore,this study was conducted to investigate the properties of concrete which uses coconut shell powder (CSP) filler material and to define the optimum percentage of CSP which can be used asfiller material in concrete. Comparisons have been made between normal concrete mixes andconcrete containing CSP. In this study, CSP was added into concrete mixes invaryingpercentages (0%, 2%, 4%, 6%, 8% and 10%). The coconut shell was grounded into afine powder before use. Experimental tests which have been conducted in this study include theslump test, compressive test and splitting tensile strength test. CSP have the potential to be used as a concrete filler and thus the findings of this study may be applied to the construction industry. The use of CSP as a filler in concrete can help make the earth a more sustainable and greener place to live in.

Surface modification of active material structures in battery electrodes

DOEpatents

Erickson, Michael; Tikhonov, Konstantin

2016-02-02

Provided herein are methods of processing electrode active material structures for use in electrochemical cells or, more specifically, methods of forming surface layers on these structures. The structures are combined with a liquid to form a mixture. The mixture includes a surface reagent that chemically reacts and forms a surface layer covalently bound to the structures. The surface reagent may be a part of the initial liquid or added to the mixture after the liquid is combined with the structures. In some embodiments, the mixture may be processed to form a powder containing the structures with the surface layer thereon. Alternatively, the mixture may be deposited onto a current collecting substrate and dried to form an electrode layer. Furthermore, the liquid may be an electrolyte containing the surface reagent and a salt. The liquid soaks the previously arranged electrodes in order to contact the structures with the surface reagent.

Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

PubMed

Przepiórkowska, A; Chrońska, K; Zaborski, M

2007-03-06

The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

Solute-Filled Syringe For Formulating Intravenous Solution

NASA Technical Reports Server (NTRS)

Owens, Jim; Bindokas, AL; Dudar, Tom; Finley, Mike; Scharf, Mike

1993-01-01

Prefilled syringe contains premeasured amount of solute in powder or concentrate form used to deliver solute to sterile interior of large-volume parenteral (LVP) bag. Predetermined amount of sterile water also added to LVP bag through sterilizing filter, and mixed with contents of syringe, yielding sterile intravenous solution of specified concentration.

21 CFR 355.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... where the water supply contains 0 to 0.7 parts per million (ppm) fluoride ion. (i) Preventive treatment... rinse in a concentrated form to be mixed with water before using to result in the appropriate fluoride.... A fluoride treatment rinse prepared by adding the powder (a concentrated solid dosage form) to water...

21 CFR 355.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-04-01

... where the water supply contains 0 to 0.7 parts per million (ppm) fluoride ion. (i) Preventive treatment... rinse in a concentrated form to be mixed with water before using to result in the appropriate fluoride.... A fluoride treatment rinse prepared by adding the powder (a concentrated solid dosage form) to water...

21 CFR 355.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... where the water supply contains 0 to 0.7 parts per million (ppm) fluoride ion. (i) Preventive treatment... rinse in a concentrated form to be mixed with water before using to result in the appropriate fluoride.... A fluoride treatment rinse prepared by adding the powder (a concentrated solid dosage form) to water...

Preparation of prepreg graphite tape with insoluble polymer

NASA Technical Reports Server (NTRS)

Yates, C. I.

1973-01-01

Powdered polymer is finely ground. Second polymer, soluble, is mixed with appropriate solvent. Milled polymer and graphite filaments are added to soluble polymer-solvent solution to create slurry. Slurry is dried, and when ready for processing, the soluble, binder-polymer is removed by heat during precure or cure cycle.

Effect of incubation time, inoculum size, temperature, pasteurization time, goat milk powder and whey powder on ACE inhibitory activity in fermented milk by L. plantarum LP69.

PubMed

Shu, Guowei; Yang, Hui; Chen, He; Zhang, Qiuhong; Tian, Yue

2015-01-01

Angiotensin I converting enzyme (ACE) plays an important physiological role in regulating hypertension. Lactic acid bacteria are known to produce ACE inhibitory peptides which can lower hypertension during fermentation. The effect of incubation time (0~36 h), inoculum size (3, 4, 5, 6 and 7%, v/v), temperature (25, 30, 35, 40 and 45°C), sterilization time (5, 10, 15, 20 and 25 min), concentration of goat milk powder (8, 10, 12, 14 and 16%, w/v) and whey powder (0.5, 0.6, 0.7, 0.8 and 0.9%, w/v) on ACE inhibitory peptides fermented from goat milk by Lactobacillus plantarum LP69 was investigated using single factor experiment. The optimal incubation time, inoculum size, temperature, pasteurization time, goat milk powder and whey powder in fermented milk by L. plantarum LP69 was 14 h, 3.0%, 35°C, 20 min, 14% and 0.70% for ACE inhibitory activity and 22 h, 3.0%, 40°C, 25 min, 16% and 0.60% for viable cell counts, respectively. The incubation time, inoculum size, temperature, pasteurization time, goat milk powder and whey powder had a significant influence on ACE inhibitory activity in fermented milk by Lactobacillus plantarum LP69, the results are beneficial for further screening of main factors by using fractional factorial designs.

Effect of Fortification with Fish (Pseudophycis bachus) Powder on Nutritional Quality of Durum Wheat Pasta.

PubMed

Desai, Ajay S; Brennan, Margaret A; Brennan, Charles S

2018-04-17

This paper investigates the nutraceutical (phenolic content and antioxidant activity) and nutritional potential (protein and starch digestibility) of supplementation of durum wheat semolina with 5–20% fish powder ( Pseudophycis bachus ). In general, all enriched pasta with fish powder showed a significant decrease ( p < 0.05) in reducing sugar released during an in vitro digestion, and reductions in standardized area under the curve (AUC) values, compared to control pasta. The potentially bioaccessible fraction of pasta enriched with 20% fish powder (FP) was characterized as having a 177–191% increase in phenolic content and a 145–556% higher antiradical activity. Elevation of these parameters in fortified pasta was accompanied by interaction of wheat starch, protein, and fish powder protein. Supplementation of fish powder also influenced protein digestibility (a reduction from 84.60% for control pasta to 80.80% for pasta with 20% fish powder). Fortification improved the nutraceutical and nutritional potential of the studied pasta with the effects depending on factors including protein-starch-phenolic interactions.

A Comparative Study of Production of Glass Microspheres by using Thermal Process

NASA Astrophysics Data System (ADS)

Lee, May Yan; Tan, Jully; Heng, Jerry YY; Cheeseman, Christopher

2017-06-01

Microspheres are spherical particles that can be distinguished into two categories; solid or hollow. Microspheres typical ranges from 1 to 200 μm in diameter. Microsphere are made from glass, ceramic, carbon or plastic depending on applications. Solid glass microsphere is manufactured by direct burning of glass powders while hollow glass microspheres is produced by adding blowing agent to glass powder. This paper presented the production of glass microspheres by using the vertical thermal flame (VTF) process. Pre-treated soda lime glass powder with particle sized range from 90 to 125μm was used in this work. The results showed that glass microspheres produced by two passes through the flame have a more spherical shape as compared with the single pass. Under the Scanning Electron Microscope (SEM), it is observed that there is a morphology changed from uneven surface of glass powders to smooth spherical surface particles. Qualitative analysis for density of the pre-burned and burned particles was performed. Burned particles floats in water while pre-burned particles sank indicated the change of density of the particles. Further improvements of the VTF process in terms of the VTF set-up are required to increase the transformation of glass powders to glass microspheres.

Rapid detection of talcum powder in tea using FT-IR spectroscopy coupled with chemometrics

PubMed Central

Li, Xiaoli; Zhang, Yuying; He, Yong

2016-01-01

This paper investigated the feasibility of Fourier transform infrared transmission (FT-IR) spectroscopy to detect talcum powder illegally added in tea based on chemometric methods. Firstly, 210 samples of tea powder with 13 dose levels of talcum powder were prepared for FT-IR spectra acquirement. In order to highlight the slight variations in FT-IR spectra, smoothing, normalize and standard normal variate (SNV) were employed to preprocess the raw spectra. Among them, SNV preprocessing had the best performance with high correlation of prediction (RP = 0.948) and low root mean square error of prediction (RMSEP = 0.108) of partial least squares (PLS) model. Then 18 characteristic wavenumbers were selected based on a hybrid of backward interval partial least squares (biPLS) regression, competitive adaptive reweighted sampling (CARS) algorithm and successive projections algorithm (SPA). These characteristic wavenumbers only accounted for 0.64% of the full wavenumbers. Following that, 18 characteristic wavenumbers were used to build linear and nonlinear determination models by PLS regression and extreme learning machine (ELM), respectively. The optimal model with RP = 0.963 and RMSEP = 0.137 was achieved by ELM algorithm. These results demonstrated that FT-IR spectroscopy with chemometrics could be used successfully to detect talcum powder in tea. PMID:27468701

Phase Composition, Crystallite Size and Physical Properties of B2O3-added Forsterite Nano-ceramics

NASA Astrophysics Data System (ADS)

Pratapa, S.; Chairunnisa, A.; Nurbaiti, U.; Handoko, W. D.

2018-05-01

This study was aimed to know the effect of B2O3 addition on the phase composition, crystallite size and dielectric properties of forsterite (Mg2SiO4) nano-ceramics. It utilized a purified silica sand from Tanah Laut, South Kalimantan as the source of (amorphous) silica and a magnesium oxide (MgO) powder. They were thoroughly mixed and milled prior to calcination. The addition of 1, 2, 3, and 4 wt% B2O3 to the calcined powder was done before uniaxial pressing and then sintering at 950 °C for 4 h. The phase composition and forsterite crystallite size, the microstructure and the dielectric constant of the sintered samples were characterized using X-ray diffractometer (XRD), Scanning Electron Microscope (SEM) and Vector Network Analyzer (VNA), respectively. Results showed that all samples contained forsterite, periclase (MgO) and proto enstatite (MgSiO3) with different weight fractions and forsterite crystallite size. In general, the weight fraction and crystallite size of forsterite increased with increasing B2O3 addition. The weight fraction and crystallite size of forsterite in the 4%-added sample reached 99% wt and 164 nm. Furthermore, the SEM images showed that the average grain size became slightly larger and the ceramics also became slightly denser as more B2O3 was added. The results are in accordance with density measurements using the Archimedes method which showed that the 4% ceramic exhibited 1.845 g/cm3 apparent density, while the 1% ceramic 1.681 g/cm3. We also found that the higher the density, the higher the average dielectric constant, i.e. it was 4.6 for the 1%-added sample and 6.4 for the 4%-added sample.

Hypoglycemic activity of Pyrus biossieriana Buhse leaf extract and arbutin: Inhibitory effects on alpha amylase and alpha glucosidase

PubMed Central

Yousefi, Fatemeh; Mahjoub, Soleiman; Pouramir, Mahdi; Khadir, Fatemeh

2013-01-01

Background: The mechanism of hypoglycemic and hypolipidemic activities of Pyrus biossieriana Buhse leaf extract (PbBLE) and its phytochemical component arbutin, have not been well determined. The present study was performed to understand the hypoglycemic activity mechanisms of pbBLE and arbutin more clearly. Methods: In vitro enzymatic carbohydrate digestion with PbBLE and arbutin was assessed using α-amylase and α-glucosidase powders. The enzyme solutions were premixed with PbBLE and arbutin at different concentrations (0.1, 1, 10 and 100 mg/ml). Substrate solutions and colorimetric reagents were added to the reaction. The release of glucose was determined by spectrophotometric method. Acarbose was used as the positive control. Results: The extract (10, 100 mg/ ml) completely inhibit α- amylase and α- glucosidase activities. The extract produced higher reduction of α-amylase and α-glucosidase activity than arbutin. Inhibition at various concentrations (0.1, 1, 10, 100 mg/ml) were significantly different (p<0.05). Conclusion: Our results exhibited that both the extract and arbutin were able to suppress the enzymes strongly. PMID:24294470

Ceratonia siliqua L. hydroethanolic extract obtained by ultrasonication: antioxidant activity, phenolic compounds profile and effects in yogurts functionalized with their free and microencapsulated forms.

PubMed

Rached, Irada; Barros, Lillian; Fernandes, Isabel P; Santos-Buelga, Celestino; Rodrigues, Alírio E; Ferchichi, Ali; Barreiro, Maria Filomena; Ferreira, Isabel C F R

2016-03-01

Bioactive extracts were obtained from powdered carob pulp through an ultrasound extraction process and then evaluated in terms of antioxidant activity. Ten minutes of ultrasonication at 375 Hz were the optimal conditions leading to an extract with the highest antioxidant effects. After its chemical characterization, which revealed the preponderance of gallotannins, the extract (free and microencapsulated) was incorporated in yogurts. The microspheres were prepared using an extract/sodium alginate ratio of 100/400 (mg mg(-1)) selected after testing different ratios. The yogurts with the free extract exhibited higher antioxidant activity than the samples added with the encapsulated extracts, showing the preserving role of alginate as a coating material. None of the forms significantly altered the yogurt's nutritional value. This study confirmed the efficiency of microencapsulation to stabilize functional ingredients in food matrices maintaining almost the structural integrity of polyphenols extracted from carob pulp and furthermore improving the antioxidant potency of the final product.

Effects of gluten-free breads, with varying functional supplements, on the biochemical parameters and antioxidant status of rat serum.

PubMed

Świeca, Michał; Reguła, Julita; Suliburska, Joanna; Złotek, Urszula; Gawlik-Dziki, Urszula

2015-09-01

This paper examines the effects of gluten-free bread enriched with functional ingredients (milk powder, poppy, sunflower and pumpkin seeds, egg yolk, carum, hazel nuts and amaranth) on the morphological and biochemical parameters and antioxidant status of rats serum. Rats were provided test diets--gluten-free breads and water ad libitum. After 14 days, the animals were weighed and killed. A hazel nut-amaranth bread diet significantly increased the level of thrombocytes when compared to control bread. A mixed bread diet significantly decreased cholesterol levels in rats. All fortified breads decreased triglyceride levels and alanine transaminase activity and caused an increase in antiradical activity of the serum. In rats fed with poppy-milk bread, milk-seed bread and mixed bread, a marked decrease in superoxide dismutase activity was found. Enriched breads reduced the levels of triglyceride and improved the antiradical properties of serum, although the physiological relevance of this needs to be confirmed by human studies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhanced coal-dependent methanogenesis coupled with algal biofuels: Potential water recycle and carbon capture

USGS Publications Warehouse

Barnhart, Elliott P.; Davis, Katherine J.; Varonka, Matthew; Orem, William H.; Cunningham, Alfred B.; Ramsay, Bradley D.; Fields, Matthew W.

2017-01-01

Many coal beds contain microbial communities that can convert coal to natural gas (coalbed methane). Native microorganisms were obtained from Powder River Basin (PRB) coal seams with a diffusive microbial sampler placed downhole and used as an inoculum for enrichments with different nutrients to investigate microbially-enhanced coalbed methane production (MECoM). Coal-dependent methanogenesis more than doubled when yeast extract (YE) and several less complex components (proteins and amino acids) were added to the laboratory microcosms. Stimulated coal-dependent methanogenesis with peptone was 86% of that with YE while glutamate-stimulated activity was 65% of that with YE, and a vitamin mix had only 33% of the YE stimulated activity. For field application of MECoM, there is interest in identifying cost-effective alternatives to YE and other expensive nutrients. In laboratory studies, adding algal extract (AE) with lipids removed stimulated coal-dependent methanogenesis and the activity was 60% of that with YE at 27 d and almost 90% of YE activity at 1406 d. Analysis of British Thermal Unit (BTU) content of coal (a measure of potential energy yield) from long-term incubations indicated > 99.5% of BTU content remained after coalbed methane (CBM) stimulation with either AE or YE. Thus, the coal resource remains largely unchanged following stimulated microbial methane production. Algal CBM stimulation could lead to technologies that utilize coupled biological systems (photosynthesis and methane production) that sustainably enhance CBM production and generate algal biofuels while also sequestering carbon dioxide (CO2).

Bibliography on Ceramic Matrix Composites and Reinforcing Whiskers, Platelets, and Fibers, 1970-1990

DTIC Science & Technology

1993-08-01

Ballistic A Study of the Critical Factors Controlling the Impact on Three Composite Ceramics Synthesis of Ceramic Matrix Composites from Snedeker, R. S...1.2.1.55 1.22.2 Mechanical and Structural Characterize’ion of Oxidation Kinetics of Silicon Carbide Whiskers the Nicalon Silicon Carbide Fibre Studied by X...Powders and Whiskers: An XPS Study 9 (10), 1218-20, Oct 1990 Taylor, T. N. (AD D250 694) J. Mater. Res. 4 (1), 189-203, Jan-Feb 1989 1.2.2.11 (AD D250 571

Quality Characteristics, Changes in Physiochemical Properties and Functional Properties of Camembert Cheese Containing Red Ginseng Powder.

PubMed

Lee, Jai-Sung; Bae, Inhyu

2018-02-01

Effects of quality, physicochemical properties and antioxidants in Camembert cheese added with red ginseng powder (RGP) were investigated. Cheese samples were prepared with 0.05%, 0.10%, 0.15% and 0.20% RGP. and then monitored during ripening at 14°C for 28 d. The pH of the RGP amended treatment groups increased during the ripening period relative to the control ( p <0.05). Moreover, the 1,2-Diphenyl-1-picrylhydrazyle (DPPH) was highest in the 0.15% RGP group from 21 d to 28 d. ABTS + radical scavenging activity was increased just like DPPH as the ripening period passed, 0.10% treatment was highest at from 7 d to 21 d. 0.15% RGP was contents of ginsenosides : 10,999.7 ppm. The Free fatty acids (FFA), controls with 0.15% treatment, while the total fat (TF) and monounsaturated fat (MuSF) were higher in the control than the 0.15% RGP group ( p <0.05). The total free amino acid (FAA) was increased in the control, and 0.15% RGP, and control was highest at then 0.15% RGP. The samples had average contents of fat and protein were 29% and 18-20% respectively. Additionally, the L* value decreased, while the a* and b* values increased as the amount of RGP added increased. Sensory evaluation revealed that texture and total acceptability were higher in the control group at 12 d. Although the addition of RGP did not exert a better effect on the ripening of the camembert cheese, but the ripening grade was similar to that of the common camembert cheese, and the additional function of the cheese was reinforced. Functional cheese could be developed.

Quality Characteristics, Changes in Physiochemical Properties and Functional Properties of Camembert Cheese Containing Red Ginseng Powder

PubMed Central

Lee, Jai-Sung; Bae, Inhyu

2018-01-01

Effects of quality, physicochemical properties and antioxidants in Camembert cheese added with red ginseng powder (RGP) were investigated. Cheese samples were prepared with 0.05%, 0.10%, 0.15% and 0.20% RGP. and then monitored during ripening at 14°C for 28 d. The pH of the RGP amended treatment groups increased during the ripening period relative to the control (p<0.05). Moreover, the 1,2-Diphenyl-1-picrylhydrazyle (DPPH) was highest in the 0.15% RGP group from 21 d to 28 d. ABTS+ radical scavenging activity was increased just like DPPH as the ripening period passed, 0.10% treatment was highest at from 7 d to 21 d. 0.15% RGP was contents of ginsenosides : 10,999.7 ppm. The Free fatty acids (FFA), controls with 0.15% treatment, while the total fat (TF) and monounsaturated fat (MuSF) were higher in the control than the 0.15% RGP group (p<0.05). The total free amino acid (FAA) was increased in the control, and 0.15% RGP, and control was highest at then 0.15% RGP. The samples had average contents of fat and protein were 29% and 18-20% respectively. Additionally, the L* value decreased, while the a* and b* values increased as the amount of RGP added increased. Sensory evaluation revealed that texture and total acceptability were higher in the control group at 12 d. Although the addition of RGP did not exert a better effect on the ripening of the camembert cheese, but the ripening grade was similar to that of the common camembert cheese, and the additional function of the cheese was reinforced. Functional cheese could be developed. PMID:29725225

A micronutrient powder with low doses of highly absorbable iron and zinc reduces iron and zinc deficiency and improves weight-for-age Z-scores in South African children.

PubMed

Troesch, Barbara; van Stuijvenberg, Martha E; van Stujivenberg, Martha E; Smuts, Cornelius M; Kruger, H Salomè; Biebinger, Ralf; Hurrell, Richard F; Baumgartner, Jeannine; Zimmermann, Michael B

2011-02-01

Micronutrient powders (MNP) are often added to complementary foods high in inhibitors of iron and zinc absorption. Most MNP therefore include high amounts of iron and zinc, but it is no longer recommended in malarial areas to use untargeted MNP that contain the Reference Nutrient Intake for iron in a single serving. The aim was to test the efficacy of a low-iron and -zinc (each 2.5 mg) MNP containing iron as NaFeEDTA, ascorbic acid (AA), and an exogenous phytase active at gut pH. In a double-blind controlled trial, South African school children with low iron status (n = 200) were randomized to receive either the MNP or the unfortified carrier added just before consumption to a high-phytate maize porridge 5 d/wk for 23 wk; primary outcomes were iron and zinc status and a secondary outcome was somatic growth. Compared with the control, the MNP increased serum ferritin (P < 0.05), body iron stores (P < 0.01) and weight-for-age Z-scores (P < 0.05) and decreased transferrin receptor (P < 0.05). The prevalence of iron deficiency fell by 30.6% (P < 0.01) and the prevalence of zinc deficiency decreased by 11.8% (P < 0.05). Absorption of iron from the MNP was estimated to be 7-8%. Inclusion of an exogenous phytase combined with NaFeEDTA and AA may allow a substantial reduction in the iron dose from existing MNP while still delivering adequate iron and zinc. In addition, the MNP is likely to enhance absorption of the high native iron content of complementary foods based on cereals and/or legumes.

Consumer acceptability and sensory profile of cooked broccoli with mustard seeds added to improve chemoprotective properties.

PubMed

Ghawi, Sameer Khalil; Shen, Yuchi; Niranjan, Keshavan; Methven, Lisa

2014-09-01

Broccoli, a rich source of glucosinolates, is a commonly consumed vegetable of the Brassica family. Hydrolysis products of glucosinolates, isothiocyanates, have been associated with health benefits and contribute to the flavor of Brassica. However, boiling broccoli causes the myrosinase enzyme needed for hydrolysis to denature. In order to ensure hydrolysis, broccoli must either be mildly cooked or active sources of myrosinase, such as mustard seed powder, can be added postcooking. In this study, samples of broccoli were prepared in 6 different ways; standard boiling, standard boiling followed by the addition of mustard seeds, sous vide cooking at low temperature (70 °C) and sous vide cooking at higher temperature (100 °C) and sous vide cooking at higher temperature followed by the addition of mustard seeds at 2 different concentrations. The majority of consumers disliked the mildly cooked broccoli samples (70 °C, 12 min, sous vide) which had a hard and stringy texture. The highest mean consumer liking was for standard boiled samples (100 °C, 7 min). Addition of 1% mustard seed powder developed sensory attributes, such as pungency, burning sensation, mustard odor, and flavor. One cluster of consumers (32%) found mustard seeds to be a good complement to cooked broccoli; however, the majority disliked the mustard-derived sensory attributes. Where the mustard seeds were partially processed, doubling the addition to 2% led to only the same level of mustard and pungent flavors as 1% unprocessed seeds, and mean consumer liking remained unaltered. This suggests that optimization of the addition level of partially processed mustard seeds may be a route to enhance bioactivity of cooked broccoli without compromising consumer acceptability. © 2014 Institute of Food Technologists®

In situ and Enriched Microbial Community Composition and Function Associated with Coal Bed Methane from Powder River Basin Coals

NASA Astrophysics Data System (ADS)

Barnhart, Elliott; Davis, Katherine; Varonka, Matthew; Orem, William; Fields, Matthew

2016-04-01

Coal bed methane (CBM) is a relatively clean source of energy but current CBM production techniques have not sustained long-term production or produced enough methane to remain economically practical with lower natural gas prices. Enhancement of the in situ microbial community that actively generates CBM with the addition of specific nutrients could potentially sustain development. CBM production more than doubled from native microbial populations from Powder River Basin (PRB) coal beds, when yeast extract and several individual components of yeast extract (proteins and amino acids) were added to laboratory microcosms. Microbial populations capable of hydrogenotrophic (hydrogen production/utilization) methanogenesis were detected in situ and under non-stimulated conditions. Stimulation with yeast extract caused a shift in the community to microorganisms capable of acetoclastic (acetate production/utilization) methanogenesis. Previous isotope analysis from CBM production wells indicated a similar microbial community shift as observed in stimulation experiments: hydrogenotrophic methanogenesis was found throughout the PRB, but acetoclastic methanogenesis dominated major recharge areas. In conjunction, a high proportion of cyanobacterial and algal SSU rRNA gene sequences were detected in a CBM well within a major recharge area, suggesting that these phototrophic organisms naturally stimulate methane production. In laboratory studies, adding phototrophic (algal) biomass stimulated CBM production by PRB microorganisms similarly to yeast extract (~40μg methane increase per gram of coal). Analysis of the British thermal unit (BTU) content of coal from long-term incubations indicated >99.5% of BTU content remained after CBM stimulation with either algae or yeast extract. Biomimicry of in situ algal CBM stimulation could lead to technologies that utilize coupled biological systems (photosynthesis and methane production) that sustainably enhance CBM production and generate algal biofuels while also sequestering carbon dioxide (CO2).

Sonocatalytic degradation of some dyestuffs and comparison of catalytic activities of nano-sized TiO2, nano-sized ZnO and composite TiO2/ZnO powders under ultrasonic irradiation.

PubMed

Wang, Jun; Jiang, Zhe; Zhang, Liqun; Kang, Pingli; Xie, Yingpeng; Lv, Yanhui; Xu, Rui; Zhang, Xiangdong

2009-02-01

Here, a novel sonocatalyst, composite TiO2/ZnO powder, was prepared through the combination of nano-sized TiO2 and ZnO powders. Because of the appropriate adsorbability to organic pollutants and special crystal interphase between TiO2 and ZnO particles, the composite TiO2/ZnO powder exhibits a high sonocatalytic activity under ultrasonic irradiation during the degradation of acid red B. Especially, the sonocatalytic activity of composite TiO2/ZnO powder with 4:1 molar proportion treated at 500 degrees C for 50 min showed obvious improvement compared with pure nano-sized TiO2 and ZnO powders. When the experimental conditions such as 10mg/L acid red B concentration, 1.0 g/L catalyst addition amount, pH=7.0, 20 degrees C system temperature, 100 min ultrasonic time and 50 mL total volume were adopted, the satisfactory degradation ratio and rate were obtained. All experiments indicate that the sonocatalytic method using composite TiO2/ZnO powder may be a more advisable choice for the treatments of non- or low-transparent organic wastewaters in future.

A comparison of mango seed kernel powder, mango leaf powder and Manilkara zapota seed powder for decolorization of methylene blue dye and antimicrobial activity.

PubMed

Sundararaman, B; Muthuramu, K L

2016-11-01

The waste mango seed generated from mango pulp industry in India is a major problem in handling the waste and hence, conversion of mango seed kernel. Mango seeds were collected and processed for oil extraction. Decolorization of methylene blue was achieved by mango seed kernel powder, mango leaf powder and Manilkara zapota seed powder. Higher efficiency was attained in mango seed kernel powder when compared to mango leaf powder and Manilkara zapota seed powder. A 60 to 95 % of removal efficiency was achieved by varying concentration. Effect of pH, dye concentration, adsorbent dosage and temperature were studied. Mango seed kernel powder is a better option that can be used as an adsorbent for the removal of methylene blue and basic red dye from its aqueous solutions.

Process for preparing active oxide powders

DOEpatents

Berard, Michael F.; Hunter, Jr., Orville; Shiers, Loren E.; Dole, Stephen L.; Scheidecker, Ralph W.

1979-02-20

An improved process for preparing active oxide powders in which cation hydroxide gels, prepared in the conventional manner are chemically dried by alternately washing the gels with a liquid organic compound having polar characteristics and a liquid organic compound having nonpolar characteristics until the mechanical water is removed from the gel. The water-free cation hydroxide is then contacted with a final liquid organic wash to remove the previous organic wash and speed drying. The dried hydroxide treated in the conventional manner will form a highly sinterable active oxide powder.

Ultrasound-assisted powder-coating technique to improve content uniformity of low-dose solid dosage forms.

PubMed

Genina, Natalja; Räikkönen, Heikki; Antikainen, Osmo; Heinämäki, Jyrki; Yliruusi, Jouko

2010-09-01

An ultrasound-assisted powder-coating technique was used to produce a homogeneous powder formulation of a low-dose active pharmaceutical ingredient (API). The powdered particles of microcrystalline cellulose (MCC; Avicel® PH-200) were coated with a 4% m/V aqueous solution of riboflavin sodium phosphate, producing a uniform drug layer on the particle surfaces. It was possible to regulate the amount of API in the treated powder. The thickness of the API layer on the surface of the MCC particles increased near linearly as the number of coating cycles increased, allowing a precise control of the drug content. The tablets (n = 950) prepared from the coated powder showed significantly improved weight and content uniformity in comparison with the reference tablets compressed from a physical binary powder mixture. This was due to the coated formulation remaining uniform during the entire tabletting process, whereas the physical mixture of the powders was subject to segregation. In conclusion, the ultrasound-assisted technique presented here is an effective tool for homogeneous drug coating of powders of irregular particle shape and broad particle size distribution, improving content uniformity of low-dose API in tablets, and consequently, ensuring the safe delivery of a potent active substance to patients.

Modified tricalcium silicate cement formulations with added zirconium oxide.

PubMed

Li, Xin; Yoshihara, Kumiko; De Munck, Jan; Cokic, Stevan; Pongprueksa, Pong; Putzeys, Eveline; Pedano, Mariano; Chen, Zhi; Van Landuyt, Kirsten; Van Meerbeek, Bart

2017-04-01

This study aims to investigate the effect of modifying tricalcium silicate (TCS) cements on three key properties by adding ZrO 2 . TCS powders were prepared by adding ZrO 2 at six different concentrations. The powders were mixed with 1 M CaCl 2 solution at a 3:1 weight ratio. Biodentine (contains 5 wt.% ZrO 2 ) served as control. To evaluate the potential effect on mechanical properties, the mini-fracture toughness (mini-FT) was measured. Regarding bioactivity, Ca release was assessed using ICP-AES. The component distribution within the cement matrix was evaluated by Feg-SEM/EPMA. Cytotoxicity was assessed using an XTT assay. Adding ZrO 2 to TCS did not alter the mini-FT (p = 0.52), which remained in range of that of Biodentine (p = 0.31). Ca release from TSC cements was slightly lower than that from Biodentine at 1 day (p > 0.05). After 1 week, Ca release from TCS 30 and TCS 50 increased to a level that was significantly higher than that from Biodentine (p < 0.05). After 1 month, Ca release all decreased (p < 0.05), yet TCS 0 and TCS 50 released comparable amounts of Ca as at 1 day (p > 0.05). EPMA revealed a more even distribution of ZrO 2 within the TCS cements. Particles with an un-reacted core were surrounded by a hydration zone. The 24-, 48-, and 72-h extracts of TCS 50 were the least cytotoxic. ZrO 2 can be added to TCS without affecting the mini-FT; Ca release was reduced initially, to reach a prolonged release thereafter; adding ZrO 2 made TCS cements more biocompatible. TCS 50 is a promising cement formulation to serve as a biocompatible hydraulic calcium silicate cement.

Magnetically responsive enzyme powders

NASA Astrophysics Data System (ADS)

Pospiskova, Kristyna; Safarik, Ivo

2015-04-01

Powdered enzymes were transformed into their insoluble magnetic derivatives retaining their catalytic activity. Enzyme powders (e.g., trypsin and lipase) were suspended in various liquid media not allowing their solubilization (e.g., saturated ammonium sulfate and highly concentrated polyethylene glycol solutions, ethanol, methanol, 2-propanol) and subsequently cross-linked with glutaraldehyde. Magnetic modification was successfully performed at low temperature in a freezer (-20 °C) using magnetic iron oxides nano- and microparticles prepared by microwave-assisted synthesis from ferrous sulfate. Magnetized cross-linked enzyme powders were stable at least for two months in water suspension without leakage of fixed magnetic particles. Operational stability of magnetically responsive enzymes during eight repeated reaction cycles was generally without loss of enzyme activity. Separation of magnetically modified cross-linked powdered enzymes from reaction mixtures was significantly simplified due to their magnetic properties.

Physical characterization of whole and skim dried milk powders.

PubMed

Pugliese, Alessandro; Cabassi, Giovanni; Chiavaro, Emma; Paciulli, Maria; Carini, Eleonora; Mucchetti, Germano

2017-10-01

The lack of updated knowledge about the physical properties of milk powders aimed us to evaluate selected physical properties (water activity, particle size, density, flowability, solubility and colour) of eleven skim and whole milk powders produced in Europe. These physical properties are crucial both for the management of milk powder during the final steps of the drying process, and for their use as food ingredients. In general, except for the values of water activity, the physical properties of skim and whole milk powders are very different. Particle sizes of the spray-dried skim milk powders, measured as volume and surface mean diameter were significantly lower than that of the whole milk powders, while the roller dried sample showed the largest particle size. For all the samples the size distribution was quite narrow, with a span value less than 2. The loose density of skim milk powders was significantly higher than whole milk powders (541.36 vs 449.75 kg/m 3 ). Flowability, measured by Hausner ratio and Carr's index indicators, ranged from passable to poor when evaluated according to pharmaceutical criteria. The insolubility index of the spray-dried skim and whole milk powders, measured as weight of the sediment (from 0.5 to 34.8 mg), allowed a good discrimination of the samples. Colour analysis underlined the relevant contribution of fat content and particle size, resulted in higher lightness ( L *) for skim milk powder than whole milk powder, which, on the other hand, showed higher yellowness ( b *) and lower greenness (- a *). In conclusion a detailed knowledge of functional properties of milk powders may allow the dairy to tailor the products to the user and help the food processor to perform a targeted choice according to the intended use.

The Influence of Duration of Mechanical Activation of Titanium Powder on its Morphology, Microstructure, and Microhardness

NASA Astrophysics Data System (ADS)

Ditenberg, I. A.; Korchagin, M. A.; Pinzhin, Yu. P.; Melnikov, V. V.; Tyumentsev, A. N.; Grinyaev, K. V.; Smirnov, I. V.; Radishevskii, V. L.; Tsverova, A. S.; Sukhanov, I. I.

2017-10-01

Using the methods of X-ray diffraction analysis and scanning and transmission electron microscopy, an investigation of the influence of duration of mechanical activation on morphology and structure of titanium powder is performed. In the course of processing the following stages of material transformation are revealed: fragmentation of the initial powder, conglomeration, and ovalization of the conglomerates. It is found that when the duration of mechanical activation increases, the characteristic size of coherent scattering regions is significantly decreased, which is accompanied by an increase in the value of microdistortions and intensive fragmentation of the crystal lattice inside powder particles followed by the formation of highly defective nanostructured states. The transformation of microstructure is accompanied by a considerable increase in microhardness.

Detecting multiple adulterants in dry milk using Raman chemical imaging

USDA-ARS?s Scientific Manuscript database

A Raman chemical imaging method was developed for detecting the presence of multiple chemical adulterants in dry milk powder. Four chemicals (ammonium sulfate, dicyandiamide, melamine, and urea) were added in equal concentrations, between 0.1% and 5.0%, to nonfat dry milk. An area of 25×25 mm2 for e...

Effect of freeze-dried leek powder (FDLP) and nitrite level on processing and quality characteristics of fermented sausages.

PubMed

Tsoukalas, D S; Katsanidis, E; Marantidou, S; Bloukas, J G

2011-02-01

Fermented sausages were produced with 0.84% and 1.68% freeze-dried leek powder (FDLP), providing 75 and 150 mg/kg NaNO(3), respectively, and three levels of added nitrite (0, 75, and 150 mg/kg NaNO(2). A control treatment was also produced with 150 mg/kg NaNO(2). Sausages with FDLP were darker and yellower (p<0.05) than the control. Higher FDLP levels produced less red, yellower and darker sausages (p<0.05). Lower FDLP levels resulted in higher (p<0.05) sensory scores for external appearance, flavour and overall acceptability. No differences were found among the treatments with FDLP plus 75 or 150 ppm NaNO(2) in TBA value, lightness, redness (cross section), redness stability, yellowness, texture parameters and sensory firmness, flavour and overall acceptability. The use of 0.84% FDLP and 75 ppm NaNO₂ is considered more appropriate for the production of fermented sausages, as it results in a 50% reduction in added nitrite. Copyright © 2010 Elsevier Ltd. All rights reserved.

Lead recovery from waste CRT funnel glass by high-temperature melting process.

PubMed

Hu, Biao; Hui, Wenlong

2018-02-05

In this research, a novel and effective process for waste CRT funnel glass treatment was developed. The key to this process is removal of lead from the CRT funnel glass by high-temperature melting process. Sodium carbonate powder was used as a fusion agent, sodium sulfide serves as a catalytic agent and carbon powder acts as reducing agent. Experimental results showed that lead recovery rate increased with an increase in the amount of added sodium carbonate, sodium sulfide, carbonate, temperature and holding time initially, and then reached a stable value. The maximum lead recovery rate was approximately 94%, when the optimum adding amount of sodium carbonate, sodium sulfide, carbonate, temperature and holding time were 25%, 8%, 3.6%, 1200°C and 120min, respectively. In the high-temperature melting process, lead silicate in the funnel glass was firstly reduced, and then removed. The glass slag can be made into sodium and potassium silicate by hydrolysis process. This study proposed a practical and economical process for recovery of lead and utilization of waste glass slag. Copyright © 2017 Elsevier B.V. All rights reserved.

Zircon-Based Ceramics Composite Coating for Environmental Barrier Coating

NASA Astrophysics Data System (ADS)

Suzuki, M.; Sodeoka, S.; Inoue, T.

2008-09-01

Studies on plasma spraying of zircon (ZrSiO4) have been carried out by the authors as one of the candidates for an environmental barrier coating (EBC) application, and had reported that substrate temperature is one of the most important factors to obtain crack-free and highly adhesive coating. In this study, several amounts of yttria were added to zircon powder, and the effect of the yttria addition on the structure and properties of the coatings were evaluated to improve the stability of the zircon coating structure at elevated temperature. The coatings obtained were composed of yttria-stabilized zirconia (YSZ), glassy silica, whereas the one prepared from monolithic zircon powder was composed of the metastable high temperature tetragonal phase of zirconia and glassy silica. After the heat treatment over 1200 °C, silica and zirconia formed zircon in all coatings. However, coatings with higher amounts of yttria exhibited lower amounts of zircon. This resulted in the less open porosity of the coating at elevated temperature. These yttria-added coatings also showed good adhesion even after the heat treatment, while monolithic zircon coating pealed off.

Spectroscopic investigation on the efficient organic nonlinear crystals of pure and diethanolamine added DAST.

PubMed

Karthikeyan, C; Haja Hameed, A S; Sagaya Agnes Nisha, J; Ravi, G

2013-11-01

4-N,N'-dimethylamino-N-methyl-4-stilbazolium toyslate (DAST) and diethanolamine (DEA) added DAST crystals are grown by slow cooling method. The corresponding powder samples are examined by characterization studies such as XRD, FT-IR, FT-Raman, UV-Vis-NIR and photoluminescence studies. From the powder X-ray diffraction, their lattice parameter values are found out. Since the vibrational spectra of the molecules are considerably contributed to their linear and nonlinear optical effects, Infrared and Raman spectroscopic studies are carried out for the samples. The UV-Vis-NIR absorption spectra of the samples are used to find the nature of transitions occurred in the samples. Using the density functional theory, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) analyses are done in order to explain the transition and density of states (DOS). The first order hyperpolarizability is calculated by HF and B3LYP/6-311 G(d,p) basis sets for the DAST molecule. From the photoluminescence (PL) spectral studies, the strong excitation emissions are observed. Copyright © 2013 Elsevier B.V. All rights reserved.

Additive impacts on particle emissions from heating low emitting cooking oils

NASA Astrophysics Data System (ADS)

Amouei Torkmahalleh, M.; Zhao, Y.; Hopke, P. K.; Rossner, A.; Ferro, A. R.

2013-08-01

The effect of five additives, including table salt, sea salt, black pepper, garlic powder, and turmeric, on the emission of PM2.5 and ultrafine particles (UFP) from heated cooking oil (200 °C) were studied. One hundred milligrams of the additives were added individually to either canola or soybean oil without stirring. Black pepper, table salt, and sea salt reduced the PM2.5 emission of canola oil by 86% (p < 0.001), 88% (p < 0.001), and 91% (p < 0.001), respectively. Black pepper, table salt, and sea salt also decreased the total particle number emissions of canola oil by 45% (p = 0.003), 52% (p = 0.001), and 53% (p < 0.001), respectively. Turmeric and garlic powder showed no changes in the PM2.5 and total number emissions of canola oil. Table salt and sea salt, decreased the level of PM2.5 emissions from soybean oil by 47% (p < 0.001) and 77% (p < 0.001), respectively. No differences in the PM2.5 emissions were observed when other additives were added to soybean oil. Black pepper, sea salt, and table salt reduced the total particle number emissions from the soybean oil by 51%, 61% and 68% (p < 0.001), respectively. Turmeric and garlic powder had no effect on soybean oil with respect to total particle number emissions. Our results indicate that table salt, sea salt, and black pepper can be used to reduce the particle total number and PM2.5 emissions when cooking with oil.

Enhanced Azo-Dyes Degradation Performance of Fe-Si-B-P Nanoporous Architecture

PubMed Central

Weng, Nan; Wang, Feng; Qin, Fengxiang; Tang, Wanying; Dan, Zhenhua

2017-01-01

Nanoporous structures were fabricated from Fe76Si9B10P5 amorphous alloy annealed at 773 K by dealloying in 0.05 M H2SO4 solution, as a result of preferential dissolution of α-Fe grains in form of the micro-coupling cells between α-Fe and cathodic residual phases. Nanoporous Fe-Si-B-P powders exhibit much better degradation performance to methyl orange and direct blue azo dyes compared with gas-atomized Fe76Si9B10P5 amorphous powders and commercial Fe powders. The degradation reaction rate constants of nanoporous powders are almost one order higher than those of the amorphous counterpart powders and Fe powders, accompanying with lower activation energies of 19.5 and 26.8 kJ mol−1 for the degradation reactions of methyl orange and direct blue azo dyes, respectively. The large surface area of the nanoporous structure, and the existence of metalloids as well as residual amorphous phase with high catalytic activity are responsible for the enhanced azo-dyes degradation performance of the nanoporous Fe-Si-B-P powders. PMID:28846622

Effect of Fortification with Fish (Pseudophycis bachus) Powder on Nutritional Quality of Durum Wheat Pasta

PubMed Central

Desai, Ajay S.; Brennan, Margaret A.

2018-01-01

This paper investigates the nutraceutical (phenolic content and antioxidant activity) and nutritional potential (protein and starch digestibility) of supplementation of durum wheat semolina with 5–20% fish powder (Pseudophycis bachus). In general, all enriched pasta with fish powder showed a significant decrease (p < 0.05) in reducing sugar released during an in vitro digestion, and reductions in standardized area under the curve (AUC) values, compared to control pasta. The potentially bioaccessible fraction of pasta enriched with 20% fish powder (FP) was characterized as having a 177–191% increase in phenolic content and a 145–556% higher antiradical activity. Elevation of these parameters in fortified pasta was accompanied by interaction of wheat starch, protein, and fish powder protein. Supplementation of fish powder also influenced protein digestibility (a reduction from 84.60% for control pasta to 80.80% for pasta with 20% fish powder). Fortification improved the nutraceutical and nutritional potential of the studied pasta with the effects depending on factors including protein-starch-phenolic interactions. PMID:29673139

Diversionary device

DOEpatents

Grubelich, Mark C.

2001-01-01

A diversionary device has a housing having at least one opening and containing a non-explosive propellant and a quantity of fine powder packed within the housing, with the powder being located between the propellant and the opening. When the propellant is activated, it has sufficient energy to propel the powder through the opening to produce a cloud of powder outside the housing. An igniter is also provided for igniting the cloud of powder to create a diversionary flash and bang, but at a low enough pressure to avoid injuring nearby people.

Polymer infiltration studies

NASA Technical Reports Server (NTRS)

Marchello, Joseph M.

1994-01-01

During the past three months, significant progress has been made on the preparation of carbon fiber composites using advanced polymer resins. The results are set forth in recent reports and publications, and will be presented at forthcoming national and international meetings. Current and ongoing research activities reported herein include: textile composites from powder-coated towpreg - role of surface coating in braiding; prepregger hot sled operation in making tape from powder coated tow; ribbonizing powder-impregnated towpreg; textile composites from powder-coated towpreg - role of bulk factor in consolidation; powder curtain prepreg process improvements in doctoring of powder; and hot/cold shoe for ATP open-section part warpage control.

Active films based on cocoa extract with antioxidant, antimicrobial and biological applications.

PubMed

Calatayud, Marta; López-de-Dicastillo, Carolina; López-Carballo, Gracia; Vélez, Dinoraz; Hernández Muñoz, Pilar; Gavara, Rafael

2013-08-15

Novel films of ethylene-vinyl alcohol copolymer (EVOH) containing flavonoid-rich cocoa were developed. To understand their potential application as active packaging material, antioxidant and antimicrobial properties of the films were determined as well as the antioxidant activity of the release compounds in Caco-2 human epithelial colorectal adenocarcinoma cells. Exposure of the films to aqueous food simulant showed antioxidant capacity. The release of cocoa extract components was dependent on the antioxidant concentration incorporated in the film and on temperature. Cocoa extract and the fraction obtained after in vitro gastrointestinal digestion presented antioxidant activity against oxidative stress induced by hydrogen peroxide in Caco-2 cells. Films with 10%, 15%, and 20% cocoa extract produced bactericidal effect against Staphylococcus aureus, Listeria monocytogenes, Escherichia coli and Salmonella enterica. The application of films to an infant milk formula, previously inoculated with L. monocytogenes, inhibited the growth of bacteria 1.5 log units the first day and showed sustained release, inhibiting 0.52 and 0.76 log units, respectively, by the sixth day, while cocoa powder added directly did not produce any effect. Published by Elsevier Ltd.

The application dosage of Azolla pinnata in fresh and powder form as organic fertilizer on soil chemical properties, growth and yield of rice plant

NASA Astrophysics Data System (ADS)

Setiawati, Mieke Rochimi; Damayani, Maya; Herdiyantoro, Diyan; Suryatmana, Pujawati; Anggraini, Derisfha; Khumairah, Fiqriah Hanum

2018-02-01

The yield of rice plants is strongly influenced by N fertilizer. Nitrogen in rice plants has roles in vegetative growth, tiller formation and increasing yield through rice protein formation. Nitrogen supplied from organic fertilizers is better than inorganic fertilizers that may have environmental problem effects. Organic fertilizers from Azolla pinnata water fern contain higher N than other organic fertilizers. Symbiosis between A. pinnata and the N-fixing cyanobacteria results in high content of nitrogen, 3 to 5%. A. pinnata can be added to the rice field as organic fertilizer in form of fresh biomass or composted. Composted form can be ground into powder which passes through 100 mesh sieve. Preparation of compost powder of A. pinnata is done to reduce the constraints of voluminous application of organic fertilizers and to improve the efficiency of its use. The objective of this research was to compare the effect of the use of fresh A. pinnata and compost powder of A. pinnata on some soil and plant chemical properties and rice yield. The treatments applied were fresh A. pinnata at the dose of 0, 10 and 20 ton ha-1 and A. pinnata compost powder at 12.5 and 25 kg ha-1. The results showed that incorporation of fresh A. pinnata at 20 tons ha-1 and its compost powder at 25 kg ha-1 increased the available P of soil, plant P content and tiller number, but did not affect the content of organic-C, total soil N, plant N content and rice yield. This study suggested the benefits of A. pinnata compost powder technology in organic fertilization of soil to increase the nutrient content of soil and rice plants.

Nitride Fuel Development Using Cryo-process Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Brandi M; Windes, William E

A new cryo-process technique has been developed for the fabrication of advanced fuel for nuclear systems. The process uses a new cryo-processing technique whereby small, porous microspheres (<2000 µm) are formed from sub-micron oxide powder. A simple aqueous particle slurry of oxide powder is pumped through a microsphere generator consisting of a vibrating needle with controlled amplitude and frequency. As the water-based droplets are formed and pass through the microsphere generator they are frozen in a bath of liquid nitrogen and promptly vacuum freeze-dried to remove the water. The resulting porous microspheres consist of half micron sized oxide particles heldmore » together by electrostatic forces and mechanical interlocking of the particles. Oxide powder microspheres ranging from 750 µm to 2000 µm are then converted into a nitride form using a high temperature fluidized particle bed. Carbon black can be added to the oxide powder before microsphere formation to augment the carbothermic reaction during conversion to a nitride. Also, the addition of ethyl alcohol to the aqueous slurry reduces the surface tension energy of the droplets resulting in even smaller droplets forming in the microsphere generator. Initial results from this new process indicate a lower impurity contamination in the final nitrides due to the single feed stream of particles, material handling and conversion are greatly simplified, a minimum of waste and personnel exposure are anticipated, and finally the conversion kinetics may be greatly increased because of the small oxide powder size (sub-micron) forming the porous microsphere. Thus far the fabrication process has been successful in demonstrating all of these improvements with surrogate ZrO2 powder. Further tests will be conducted in the future using the technique on UO2 powders.« less

Synergistic effects of sour taste and low temperature in suppressing the bitterness of Aminoleban® EN.

PubMed

Haraguchi, Tamami; Yoshida, Miyako; Hazekawa, Mai; Uchida, Takahiro

2011-01-01

Aminoleban® EN, a nutritional product for patients with liver failure, contains three branched-chain amino acids (BCAAs): L-leucine, L-isoleucine, and L-valine. As BCAAs are extremely bitter, Aminoleban® EN has a low palatability, which is a major cause of patient noncompliance. Nutrients for liver failure often need to be taken for long periods, and poor medication compliance can cause serious problems, such as encephalopathy. Therefore it is important to suppress the bitter taste of Aminoleban® EN and thereby improve patient compliance. There are already six different flavoured powders (coffee, green-tea, apple, fruit, plum and pineapple) which can be added to Aminoleban® EN to reduce its unpleasant taste and smell, but it is possible that other factors, such as temperature, may also improve the palatability of Aminoleban® EN. In this study, flavours alone significantly decreased the bitterness intensity of Aminoleban® EN. It was thought that the sweetness and sourness of the flavoured powder would be the main factors involved in decreasing the bitterness. However, low temperature (0-5 °C) decreased the bitterness intensity of Aminoleban® EN, with or without the flavoured powders, compared with normal room temperature (25-30 °C). The sourness intensity of flavoured powders was not decreased at low temperatures, but the sweetness intensity of some flavoured powders did decrease. These results suggest that sourness can be tasted even at low temperatures. As not only the addition of flavoured powders but also low temperatures can reduce the bitterness of Aminioleban® EN, the combination of a sour-flavoured powder and a low temperature will improve the palatability of Aminoleban® EN the most.

Preventing airborne infection with an intranasal cellulose powder formulation (Nasaleze travel).

PubMed

Hiltunen, Raimo; Josling, Peter D; James, Mike H

2007-01-01

A total of 52 volunteers were recruited to take part in a dual-centered, randomized, blinded study so investigators could determine whether the level of airborne infection could be significantly reduced in patients randomly assigned to treatment with either Nasaleze cellulose extract alone or a combination of Nasaleze cellulose and powdered garlic extract (PGE). One puff into each nostril was recommended, and volunteers who developed an infection while traveling were told to use at least 3 puffs per nostril until symptoms were reduced. This study took place over an 8-wk period across Finland and the United Kingdom between November 2006 and March 2007. Volunteers were instructed to use a 5-point scale to assess their health and to record infectious episodes and symptoms in a daily diary. The activetreatment group (Nasaleze cellulose with PGE) experienced significantly fewer infections than the control group (20 vs 57; P<.001) and far fewer days on which an infection was obviously present (126 d in the active group vs 240 d in the control group; P<.05). Consequently, volunteers in the active group were less likely to pick up an airborne infection when PGE was added to this novel cellulose extract. Volunteers in the control group were much more likely to report more than 1 infectious episode over the treatment period or to endure longer periods of infection. The investigators concluded that the combination Nasaleze Travel formulation significantly reduced the number of airborne infections to which volunteers were exposed while traveling.

Characterization of the distribution of the sintering activator boron in powder metallurgical steels with SIMS.

PubMed

Krecar, Dragan; Vassileva, Vassilka; Danninger, Herbert; Hutter, Herbert

2004-06-01

Powder metallurgy is a well-established method for manufacturing ferrous precision parts. A very important step is sintering, which can be strongly enhanced by the formation of a liquid phase during the sintering process. Boron activates this process by forming such a liquid phase at about 1200 degrees C. In this work, the sintering of Fe-B was performed under the protective atmospheres of hydrogen, argon or nitrogen. Using different grain sizes of the added ferroboron leads to different formations of pores and to the formation of secondary pores. The effect of boron was investigated by means of Secondary Ion Mass Spectrometry (SIMS) supported by Scanning Electron Microscopy (SEM) and Light Microscopy (LM). To verify the influence of the process parameters on the mechanical properties, the microstructure (pore shape) was examined and impact energy measurements were performed. The concentrations of B in different samples were varied from 0.03-0.6 weight percent (wt%). Higher boron concentrations are detectable by EPMA, whereas the distributions of boron in the samples with interesting overall concentration in the low wt% range are only detectable by means of SIMS. This work shows that the distribution of boron strongly depends on its concentration and the sintering atmosphere used. At low concentration (up to 0.1 wt%) there are boride precipitations; at higher concentration there is a eutectic iron-boron grain boundary network. There is a decrease of the impact energy observed that correlates with the amount of eutectic phase.

[Coagulation and adsorption on treating the Yellow River and the impact on chlorine decay during chlorination process].

PubMed

Zhan, Xiao; Gao, Bao-yu; Liu, Bin; Xu, Chun-hua; Yue, Qin-yan

2010-05-01

Two types of inorganic polymer coagulants, polyferric chloride (PFC) and polyaluminum chloride (PAC), were chosen to treat the Yellow River water. Different dosages were investigated in order to investigate the turbidity, UV24, DOC and permanganate index removal efficiency and their coagulation mechanisms based on the Zeta potentials. The natural organic matter removal by the combination of coagulation and adsorption with powder activated carbon were analyzed based on different coagulant and adsorbent dosages and dosing orders. The effects of combination of coagulation and adsorption on the residual chlorine decay were analyzed. The results showed that the two coagulants had high turbidity removal efficiency ( > 90%). The UV254, DOC, permanganate index removal efficiency were 29.2%, 26.1% and 27.9% respectively for PAC coagulation and were 32.3%, 23.3% and 32.9% respectively for PFC. Electric neutralization played an important role in the PAC coagulation process while both adsorption bridging and electric neutralization performed when PFC was used. The removal percentage of organic matter increased with the increase coagulant and adsorbent. The adsorption after coagulation process gave the better UV254 and DOC removal efficiency than the coagulation after adsorption. The UV254 and DOC removal efficiency were 95.2% and 99.9% for PAC coagulation after adsorption and were 90.1% and 99.9% for PFC coagulation first. But adding powder activated carbon can improve floc settlement performance and maintained persistent disinfection effect.

Powder metallurgy: Solid and liquid phase sintering of copper

NASA Technical Reports Server (NTRS)

Sheldon, Rex; Weiser, Martin W.

1993-01-01

Basic powder metallurgy (P/M) principles and techniques are presented in this laboratory experiment. A copper based system is used since it is relatively easy to work with and is commercially important. In addition to standard solid state sintering, small quantities of low melting metals such as tin, zinc, lead, and aluminum can be added to demonstrate liquid phase sintering and alloy formation. The Taguchi Method of experimental design was used to study the effect of particle size, pressing force, sintering temperature, and sintering time. These parameters can be easily changed to incorporate liquid phase sintering effects and some guidelines for such substitutions are presented. The experiment is typically carried out over a period of three weeks.

Method for immobilizing radioactive iodine

DOEpatents

Babad, Harry; Strachan, Denis M.

1980-01-01

Radioactive iodine, present as alkali metal iodides or iodates in an aqueous solution, is incorporated into an inert solid material for long-term storage by adding to the solution a stoichiometric amount with respect to the formation of a sodalite (3M.sub.2 O.3Al.sub.2 O.sub.3. 6SiO.sub.2.2MX, where M=alkali metal; X=I.sup.- or IO.sub.3.sup.-) of an alkali metal, alumina and silica, stirring the solution to form a homogeneous mixture, drying the mixture to form a powder, compacting and sintering the compacted powder at 1073 to 1373 K (800.degree. to 1100.degree. C.) for a time sufficient to form sodalite.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sitler, Steven J.; Raja, Krishnan S.; Charit, Indrajit

Solid solutions of HfB 2-ZrB 2 mixtures were prepared by high-energy ball milling of diboride and additive powders followed by spark plasma sintering (SPS). A mixture of stoichiometric 1:1 HfB 2-ZrB 2 borides was the base composition to which Hf, Zr, Ta, LaB 6 or Gd 2O 3 was added. Hf, Zr and Ta were added in order to bring the boron-to-metal ratio down to 1.86, rendering the boride as MeB 1.86. In the case of LaB 6 and Gd 2O 3, 1.8 mol% was added. Electroanalytical behavior of hydrogen evolution reactions was evaluated in 1 M H 2SO 4more » and 1 M NaOH solutions. The LaB 6 additive material showed Tafel slopes of 125 and 90 mV/decade in acidic and alkaline solutions respectively. The Hf and Zr rich samples showed Tafel slopes of about 120 mV/decade in both electrolytes. The over potentials of hydrogen evolution reactions (at 10 mA/cm 2) in the alkaline solution were about 100 mV lower than those in acidic solution. The metal-rich diborides and addition of LaB 6 showed better hydrogen evolution reaction (HER) activities than the base 1:1 HfB 2-ZrB 2 stoichiometric diboride solid solution. Furthermore, the higher activity of metal-rich borides could be attributed to the increased electron population at the d-orbitals of the metal shown by band structure modeling calculations using the Density Functional Theory approach.« less

Impact of functionalized particle structure on roll compaction/dry granulation and tableting of calcium carbonate.

PubMed

Grote, Simon; Kleinebudde, Peter

2018-06-10

The influence of a functionalized raw material particle structure on the granulation behavior and tabletabilty of calcium carbonate (CaCO 3 ) was investigated. Therefore, a milled grade of CaCO 3 was compared to different binary mixtures of milled and functionalized CaCO 3 . Relevant properties of raw materials, ribbons and granules were measured. The starting materials and two fractions of dry granules were compressed to tablets. The tabletability of granules was compared to that of the powders and the influence of specific compaction force and granule size on tablet tensile strength was evaluated. Adding functionalized particles drastically influenced the granulation and tableting behavior of CaCO 3 . Increasing proportions increased the ribbon porosity and granule size. Tensile strength of tablets from powder mixtures and granules was increased as well. Nevertheless, adding functionalized CaCO 3 led to a loss in tabletability induced by a previous compaction step to an extent depending on its proportion in the formulation. A clear influence of the particle morphology on granulation and tableting behavior was demonstrated by the study. The functionalized structure showed aspects of a more plastic deformation behavior. Adding functionalized CaCO 3 to a mixture, even in small amounts, seemed to be beneficial to increase granule size and tablet strength. Copyright © 2018 Elsevier B.V. All rights reserved.

Environmentally-friendly oxygen-free roasting/wet magnetic separation technology for in situ recycling cobalt, lithium carbonate and graphite from spent LiCoO2/graphite lithium batteries.

PubMed

Li, Jia; Wang, Guangxu; Xu, Zhenming

2016-01-25

The definite aim of the present paper is to present some novel methods that use oxygen-free roasting and wet magnetic separation to in situ recycle of cobalt, Lithium Carbonate and Graphite from mixed electrode materials. The in situ recycling means to change waste into resources by its own components, which is an idea of "waste+waste→resources." After mechanical scraping the mixed electrode materials enrich powders of LiCoO2 and graphite. The possible reaction between LiCoO2 and graphite was obtained by thermodynamic analysis. The feasibility of the reaction at high temperature was studied with the simultaneous thermogravimetry analysis under standard atmospheric pressure. Then the oxygen-free roasting/wet magnetic separation method was used to transfer the low added value mixed electrode materials to high added value products. The results indicated that, through the serious technologies of oxygen-free roasting and wet magnetic separation, mixture materials consist with LiCoO2 and graphite powders are transferred to the individual products of cobalt, Lithium Carbonate and Graphite. Because there is not any chemical solution added in the process, the cost of treating secondary pollution can be saved. This study provides a theoretical basis for industrial-scale recycling resources from spent LIBs. Copyright © 2015 Elsevier B.V. All rights reserved.

Production of Spirulina sp by utilization of wastewater from the powder type energy drinks

NASA Astrophysics Data System (ADS)

Sumantri, Indro; Priyambada, Ika Bagus

2015-12-01

Wastewater of energy drink type of powder produced when the the production equipment required cleaning treatment to produce one taste to others. These equipments washed by water, so that, it produced wastewater. It contains high organic substances and classified as high degradable due to food product. The content of wastewater is high carbon and nitrogen substances. Microalgae is an autotrophic microorganism, live without carbon presence, utilized to digest the substances in wastewater especially for nitrogen substances. Spirulina sp is the type of microalgae selected to utilize the wastewater of energy drink, the selection criteria is the size of Spirulina sp is relatively large and easy to separated from its solution. The experiment conducted by cultivate the seeding microalgae with certain nutrients until the certain volume. The synthetic wastewater obtained from one of energy drink type of powder with commercial brand as Kuku Bima Ener-G, the wastewater concentration selected under the close to the real condition of wastewater as basis of COD measurement (6 sachet/L or COD of 12.480mg/L) and aqueous concentration (1 sachet/L or COD of 2080mg/L). The batch experiments with 1L volume conducted and with variable of percent volume of wastewater added in order to observe the growth of microlagae. The response of the microalgae growth obtained by increasing the optical density of the microalgae solution and continued by calculation for the growth rate of microalgae. The result of the experiments indicated that for the aqueous concentration (1 sachet/L or COD of 2080mg/L) the optimum added of wastewater is 40 % with growrate of 0.55/day while for the concentrated wastewater (6 sachet/L or COD of 12.480mg/L), the optimum condition is 25 % wastewater added with growth rate of 0.43/day.

SU-E-T-609: Perturbation Effects of Pedicle Screws On Radiotherapy Dose Distributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bar-Deroma, R; Borzov, E; Nevelsky, A

2015-06-15

Purpose: Radiation therapy in conjunction with surgical implant fixation is a common combined treatment in case of bone metastases. However, metal implants generally used in orthopedic implants perturb radiation dose distributions. Carbon-Fiber Reinforced (CFR) PEEK material has been recently introduced for production of intramedullary screws and plates. Gold powder can be added to the CFR-PEEK material in order to enhance visibility of the screws during intraoperative imaging procedures. In this work, we investigated the perturbation effects of the pedicle screws made of CFR-PEEK, CFR-PEEK with added gold powder (CFR-PEEK-AU) and Titanium (Ti) on radiotherapy dose distributions. Methods: Monte Carlo (MC)more » simulations were performed using the EGSnrc code package for 6MV beams with 10×10 fields at SSD=100cm. By means of MC simulations, dose distributions around titanium, CFR- PEEK and CFR-PEEK-AU screws (manufactured by Carbo-Fix Orthopedics LTD, Israel) placed in a water phantom were calculated. The screw axis was either parallel or perpendicular to the beam axis. Dose perturbation (relative to dose in homogeneous water phantom) was assessed. Results: Maximum overdose due to backscatter was 10% for the Ti screws, 5% for the CFR-PEEK-AU screws and effectively zero for the CFR-PEEK screws. Maximum underdose due to attenuation was 25% for the Ti screws, 15% for the CFR-PEEK-AU screws and 5% for the CFR-PEEK screws. Conclusion: Titanium screws introduce the largest distortion on the radiation dose distribution. The gold powder added to the CFR-PEEK material improves visibility at the cost of increased dose perturbation. CFR-PEEK screws caused minimal alteration on the dose distribution. This can decrease possible over and underdose of adjacent tissue and thus favorably influence treatment efficiency. The use of such implants has potential clinical advantage in the treatment of neoplastic bone disease.« less

Storage study and quality evaluation of coconut protein powder.

PubMed

Naik, Aduja; Prakash, Maya; R, Ravi; Raghavarao, Ksms

2013-11-01

Coconut skim milk and insoluble protein are 2 major byproducts in the production of virgin coconut oil. Coconut skim milk was homogenized along with insoluble protein and spray dried to obtain a value-added product, namely, coconut protein powder (CPP). This study deals with the storage study of CPP under different conditions (refrigerated [control], ambient and accelerated). CPP samples were withdrawn periodically at designated intervals of 15 d for accelerated and control, and 30 d for ambient condition. CPP stored at different conditions exhibited marginal moisture uptake (by 0.74 % w/w for control, 0.76 % w/w for ambient, and 1.26 % w/w for accelerated condition) and as a result, had very little effect on the functional properties of the powder. Withdrawn CPP was tested for sensory quality aspects and subjected to instrumental analysis as well. Withdrawn CPP was incorporated as a milk substitute in dessert (Kheer). Quantitative descriptive analysis of the powder and product (Kheer) showed no significant difference in attributes of CPP during the storage period of 2 mo. Electronic nose analysis revealed that CPP samples were not much different with respect to aroma pattern matching, respectively. © 2013 CSIR-Central Food Technological Research Institute.

Antioxidative effect of Assam Tea (Camellia sinesis Var. Assamica) extract on rice bran oil and its application in breakfast cereal.

PubMed

Utama-Ang, Niramon; Phawatwiangnak, Kamonyanun; Naruenartwongsakul, Srisuwan; Samakradhamrongthai, Rajnibhas

2017-04-15

The objectives of this research were to investigate the antioxidant effect of Assam tea extract (ATE) and whether it is fit to utilise ATE by fortification in rice bran breakfast cereal (RBC). The increasing ATE powder from 0.1 to 0.3mg/g affected to be decreased. The ATE powder at 0.3mg/g was proved to have decreased the hexanal content (0.21μg/ml) and thiobarbituric acid reactive substances (TBARS) (2.56μg/g) within 28days, and provided the highest antioxidant ability (EC50) (2481.44mg/kg). The fortified 0.3mg/g of ATE powder showed that increasing ATE significantly increased the total phenolic content and decreased TBARS and EC50 of breakfast cereal (p<0.05). The suitable amount ATE powder added in RBC was 0.5%. The consumer acceptance (n=200) of final product showed the sensory scores in the range of 6.3-6.8, with the percentages of acceptance and purchase intention at 98.0% and 89.0%, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reduction experiment of iron scale by adding waste plastics.

PubMed

Zhang, Chongmin; Chen, Shuwen; Miao, Xincheng; Yuan, Hao

2009-01-01

The special features of waste plastics in China are huge in total amount, various in type and dispersive in deposition. Therefore, it is necessary to try some new ways that are fit to Chinese situation for disposing waste plastics as metallurgical raw materials more effectively and flexibly. Owing to its high ferrous content and less impurity, the iron scale became ideal raw material to produce pure iron powder. One of the methods to produce pure iron powder is Hoganas Method, by which, after one or multistage of reduction steps, the iron scale can be reduced pure iron powder. However, combining utilization of waste plastics and iron powder production, a series of reduction experiments were arranged and investigated, which is hoped to take use of both thermal and chemical energy contained in waste plastics as well as to improve the reducing condition of iron scale, and hence to develop a new metallurgical way of disposing waste plastics. The results show that under these experimental conditions, the thermal-decomposition of water plastics can conduce to an increase of porosity in the reduction systems. Moreover, better thermodynamics and kinetics conditions for the reduction of scale can be reached. As a result, the reduction rate is increased.

Green biosynthesis of silver nanoparticles using Curcuma longa tuber powder

PubMed Central

Shameli, Kamyar; Ahmad, Mansor Bin; Zamanian, Ali; Sangpour, Parvanh; Shabanzadeh, Parvaneh; Abdollahi, Yadollah; Zargar, Mohsen

2012-01-01

Green synthesis of noble metal nanoparticles is a vastly developing area of research. Metallic nanoparticles have received great attention from chemists, physicists, biologists, and engineers who wish to use them for the development of a new-generation of nanodevices. In this study, silver nanoparticles were biosynthesized from aqueous silver nitrate through a simple and eco-friendly route using Curcuma longa tuber-powder extracts, which acted as a reductant and stabilizer simultaneously. Characterizations of nanoparticles were done using different methods, which included ultraviolet-visible spectroscopy, powder X-ray diffraction, transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray fluorescence spectrometry, and Fourier-transform infrared spectroscopy. The ultraviolet-visible spectrum of the aqueous medium containing silver nanoparticles showed an absorption peak at around 415 nm. Transmission electron microscopy showed that mean diameter and standard deviation for the formation of silver nanoparticles was 6.30 ± 2.64 nm. Powder X-ray diffraction showed that the particles are crystalline in nature, with a face-centered cubic structure. The most needed outcome of this work will be the development of value-added products from C. longa for biomedical and nanotechnology-based industries. PMID:23341739

Evaluation of antioxidant, rheological, physical and sensorial properties of wheat flour dough and cake containing turmeric powder.

PubMed

Park, S H; Lim, H S; Hwang, S Y

2012-10-01

The effects of addition of turmeric powder (0%, 2%, 4%, 6% and 8%) were examined in order to obtain an antioxidant-enriched cake with good physico-chemical and sensorial properties. The rheological properties of doughs were evaluated using dynamic rheological measurements. Physical properties, curcumin content, radical scavenging activity (RSA-DPPH assay) and sensory analysis (hedonic test) of the supplemented cake were determined. Addition of turmeric powder up to 8% caused significant changes on dough characteristics and on cake rheological properties. The highest curcumin (203 mg/kg) and RSA-DPPH activity (45%) were achieved in the cake having the highest percentage of turmeric powder (8%); however, this sample showed the worst results regarding the rheological properties. Moreover, by sensory evaluation this cake sample was not acceptable. A 6% substitution of wheat flour with turmeric powder showed acceptable sensory scores which were comparable to those of 0-4% turmeric cakes. This indicated that up to 6% level of turmeric powder might be included in cake formulation.

Synthesis of crystalline Ce-activated garnet phosphor powders and technique to characterize their scintillation light yield

NASA Astrophysics Data System (ADS)

Gordienko, E.; Fedorov, A.; Radiuk, E.; Mechinsky, V.; Dosovitskiy, G.; Vashchenkova, E.; Kuznetsova, D.; Retivov, V.; Dosovitskiy, A.; Korjik, M.; Sandu, R.

2018-04-01

This work reports on a process of preparation of garnet phosphor powders and a technique for light yield evaluation of strongly light scattering samples. Powders of scintillation compounds could be used as individual materials or as samples for express tests of scintillation properties. However, estimation of their light yield (LY) is complicated by strong light scattering of this kind of materials. Ce3+-activated yttrium-aluminum and gallium-gadolinium-aluminum garnet phosphor powders, Y3Al5O12 (YAG:Ce) and Gd3Ga3Al2O12 (GGAG:Ce), were obtained using a modified coprecipitation technique. Ga tends to residue in mother liquor in ammonia media, but the modification allows to avoid the loss of components. We propose an approach for sample preparation and LY measurement setup with alpha particles excitation, allowing to decrease light scattering influence and to estimate a light yield of powder samples. This approach is used to evaluate the obtained powders.

Fast and selective determination of total protein in milk powder via titration of moving reaction boundary electrophoresis.

PubMed

Guo, Cheng-ye; Wang, Hou-yu; Liu, Xiao-ping; Fan, Liu-yin; Zhang, Lei; Cao, Cheng-xi

2013-05-01

In this paper, moving reaction boundary titration (MRBT) was developed for rapid and accurate quantification of total protein in infant milk powder, from the concept of moving reaction boundary (MRB) electrophoresis. In the method, the MRB was formed by the hydroxide ions and the acidic residues of milk proteins immobilized via cross-linked polyacrylamide gel (PAG), an acid-base indicator was used to denote the boundary motion. As a proof of concept, we chose five brands of infant milk powders to study the feasibility of MRBT method. The calibration curve of MRB velocity versus logarithmic total protein content of infant milk powder sample was established based on the visual signal of MRB motion as a function of logarithmic milk protein content. Weak influence of nonprotein nitrogen (NPN) reagents (e.g., melamine and urea) on MRBT method was observed, due to the fact that MRB was formed with hydroxide ions and the acidic residues of captured milk proteins, rather than the alkaline residues or the NPN reagents added. The total protein contents in infant milk powder samples detected via the MRBT method were in good agreement with those achieved by the classic Kjeldahl method. In addition, the developed method had much faster measuring speed compared with the Kjeldahl method. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of CeO₂ on Microstructure and Wear Resistance of TiC Bioinert Coatings on Ti6Al4V Alloy by Laser Cladding.

PubMed

Chen, Tao; Liu, Defu; Wu, Fan; Wang, Haojun

2017-12-31

To solve the lack of wear resistance of titanium alloys for use in biological applications, various prepared coatings on titanium alloys are often used as wear-resistant materials. In this paper, TiC bioinert coatings were fabricated on Ti6Al4V by laser cladding using mixed TiC and ZrO₂ powders as the basic pre-placed materials. A certain amount of CeO₂ powder was also added to the pre-placed powders to further improve the properties of the TiC coatings. The effects of CeO₂ additive on the phase constituents, microstructures and wear resistance of the TiC coatings were researched in detail. Although the effect of CeO₂ on the phase constituents of the coatings was slight, it had a significant effect on the microstructure and wear resistance of the coatings. The crystalline grains in the TiC coatings, observed by a scanning electron microscope (SEM), were refined due to the effect of the CeO₂. With the increase of CeO₂ additive content in the pre-placed powders, finer and more compact dendrites led to improvement of the micro-hardness and wear resistance of the TiC coatings. Also, 5 wt % content of CeO₂ additive in the pre-placed powders was the best choice for improving the wear properties of the TiC coatings.

Modelling of multi-vortex convection of fine alloying components in the molten pool under the laser radiation

NASA Astrophysics Data System (ADS)

Gurin, A. M.; Kovalev, O. B.

2013-06-01

The work is devoted to the mathematical modelling and numerical solution of the problems of conjugate micro-convection, which arises under the laser radiation action in the metal melt with surface-active refractory disperse components added for the modification, hardening, and doping of the treated surface. A multi-vortex structure of the melt flow has been obtained, the number of vortices in which depends on the surface tension variation, on the temperature and power of laser radiation. Special attention is paid to the numerical modelling of the behavior in the melt of the substrate of disperse admixture consisting of the tungsten carbide particles. The role of microconvection in the distribution of powder particles in the surface layer of the substrate after its cooling is shown.

Characteristics of activated carbon resulted from pyrolysis of the oil palm fronds powder

NASA Astrophysics Data System (ADS)

Maulina, S.; Iriansyah, M.

2018-02-01

Activated carbon is the product of a charcoal impregnation process that has a higher absorption capacity and has more benefits than regular char. Therefore, this study aims to cultivate the powder of oil palm fronds into activated carbon that meets the requirements of Standard National Indonesia 06-3730-1995. To do so, the carbonization process of the powder of oil palm fronds was carried out using a pyrolysis reactor for 30 minutes at a temperature of 150 °C, 200 °C, and 250 °C in order to produce activated char. Then, the char was impregnated using Phosphoric Acid activator (H3PO4) for 24 hours. Characteristics of activated carbon indicate that the treatment of char by chemical activation of oil palm fronds powder has an effect on the properties of activated carbon. The activated carbons that has the highest absorption properties to Iodine (822.91 mg/g) were obtained from the impregnation process with 15% concentration of Phosphoric Acid (H3PO4) at pyrolysis temperature of 200 °C. Furthermore, the activation process resulted in activated carbon with water content of 8%, ash content of 4%, volatile matter 39%, and fixed carbon 75%, Iodine number 822.91 mg/g.

A randomised controlled trial of active chronic otitis media comparing courses of eardrops versus one-off topical treatments suitable for primary, secondary and tertiary healthcare settings.

PubMed

Loock, J W

2012-08-01

Primary: to compare one-off administration of boric acid powder with courses of 1% acetic acid and ciprofloxacin eardrops in treating active chronic otitis media. Secondary: to evaluate the effectiveness of Quadriderm® cream in resistant active chronic otitis media; and to document side effects of these treatments, especially hearing loss. Randomised controlled trial. Outpatient department of a tertiary ENT unit. Hundred and fifty-nine patients over 6 years old with active chronic mucosal (without cholesteatoma) otitis media randomised to receive one of the three primary agents. All techniques employed were suitable for primary healthcare givers as well as specialists. After confirming eligibility, patients were randomly allocated to treatment. All ears underwent toilet with irrigation using clean water, a syringe and ambient light, with or without dry mopping, until the perforation was visible. The randomised solution was flushed through the middle ear and eustachian tube using a 'tragal pump' technique: saline was used as the solution for flushing in the boric acid powder arm. Patients allocated topical ear medication were given a bottle of eardrops to administer (six drops twice daily, 'pumped in') until finished. Those allocated boric acid powder had the external ear canals filled as a one-off treatment. Patients were followed up monthly thereafter. Primary: Dry (inactive) middle ears as assessed by the doctor. Secondary: Patient assessment of success; microbiologic culture and sensitivity; audiologic changes because of treatment; complications of treatment; costs of therapies. Ciprofloxacin eardrops and boric acid powder were statistically superior to 1% acetic acid eardrops in rendering active chronic otitis media inactive (73% dry ears for ciprofloxacin; 67% for boric acid powder; and 24% for acetic acid). There was no difference between the success rates of ciprofloxacin eardrops and boric acid powder. Quadriderm cream was effective in 85% of patients failing first-line therapy. No agent caused significant complications and specifically no hearing loss. This study showed a single application of boric acid powder following external auditory canal irrigation until the perforation was visible to be as effective as the current best practice of topical quinolone eardrops in active chronic otitis media. Boric acid powder is inexpensive and does not require patient compliance. Boric acid powder is a viable, less costly alternative to topical antibiotic/steroid ear drops in the developing world for active chronic otitis media. Acetic acid eardrops 1% are ineffective. Quadriderm cream, given as a one-off therapy, also appears to be effective. © 2012 Blackwell Publishing Ltd.

Utilization of biodiesel by-products for mosquito control.

PubMed

Pant, Megha; Sharma, Satyawati; Dubey, Saurabh; Naik, Satya Narayan; Patanjali, Phool Kumar

2016-03-01

The current paper has elaborated the efficient utilization of non-edible oil seed cakes (NEOC), by-products of the bio-diesel extraction process to develop a herbal and novel mosquitocidal composition against the Aedes aegypti larvae. The composition consisted of botanical active ingredients, inerts, burning agents and preservatives; where the botanical active ingredients were karanja (Pongamia glabra) cake powder and jatropha (Jatropha curcas) cake powder, products left after the extraction of oil from karanja and jatropha seed. The percentage mortality value recorded for the combination with concentration, karanja cake powder (20%) and jatropha cake powder (20%), 1:1 was 96%. The coil formulations developed from these biodiesel by-products are of low cost, environmentally friendly and are less toxic than the synthetic active ingredients. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

USING POWDERED ACTIVATED CARBON: A CRITICAL REVIEW

EPA Science Inventory

Because the performance of powdered activated carbon (PAC) for uses other than taste and odor control is poorly documented, the purpose of this article is to critically review uses that have been reported (i.e., pesticides and herbicides, synthetic organic chemicals, and trihalom...

Structural, negative thermal expansion and photocatalytic properties of ZrV{sub 2}O{sub 7}: a comparative study between fibers and powders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Qinqin, E-mail: liu_qin_qin@126.com; Yang, Juan; Rong, Xiaoqing

2014-10-15

Novel ZrV{sub 2}O{sub 7} microfibers with diameters about 1–3 μm were synthesized using a sol–gel technique. For comparison, ZrV{sub 2}O{sub 7} powders were prepared by the same method. The resultant structures were studied by X-ray diffraction, field-emission scanning electron microscopy and transmission electron microscopy. The results indicated that both the pure ZrV{sub 2}O{sub 7} microfibers and powders could be synthesized by the sol–gel technique. The thermal expansion property of the as-prepared ZrV{sub 2}O{sub 7} microfibers and powders was characterized by a thermal mechanical analyzer, both the fibers with cylindrical morphology and irregular powders with average size between 100 and 200more » nm showed negative thermal expansion between 150 °C and 600 °C. The photocatalytic activity of the microfibers was compared to that of powders under UV radiations. The band gap of ZrV{sub 2}O{sub 7} microfibers decreased and its absorption edge exhibited red shift. The microfibers also had a higher surface area compared with the powders, resulting in considerably higher photocatalytic characteristics. The large surface area and the enhanced photocatalytic activity of the ZrV{sub 2}O{sub 7} microfibers also offer potential applications in sensors and inorganic ion exchangers. - Graphical abstract: (a and c) SEM photos of ZrV{sub 2}O{sub 7} powders and fibers. (b and d) TEM images of ZrV{sub 2}O{sub 7} powders and fibers. (e) Thermal expansion curves of ZrV{sub 2}O{sub 7} powders and fibers. (f) Degradation curves of ZrV{sub 2}O{sub 7} powders and ZrV{sub 2}O{sub 7} fibers. - Highlights: • Novel ZrV{sub 2}O{sub 7} fibers could be synthesized using sol–gel technique. • ZrV{sub 2}O{sub 7} powders with irregular shape are also prepared for comparison. • Both ZrV{sub 2}O{sub 7} microfibers and powders exhibit negative thermal expansion property. • ZrV{sub 2}O{sub 7} microfibers show outstanding photocatalytic activity under UV irradiation. • This synthesis technique can be easily extended to many other functional fibers.« less

Activated mineral powders for asphalt concrete mixture

NASA Astrophysics Data System (ADS)

Kuznetsov, D. A.; Lukash, E. A.

2018-03-01

Possibilities of activation of disperse mineral powders from the technogenic raw materials of KMA by ultraviolet irradiation are considered in this article. The optimum time of ultraviolet exposure for each material is determined during which the concentration of exchange centers is increased, the rate of rehydration is slowed down and the moisture absorption is significantly reduced. It is shown that both physical and mechanical characteristics, as well as durability of asphalt concrete prepared on the basis of modified mineral powders are significantly increased.

Acetone Powder From Dormant Seeds of Ricinus communis L

NASA Astrophysics Data System (ADS)

Cavalcanti, Elisa D. C.; Maciel, Fábio M.; Villeneuve, Pierre; Lago, Regina C. A.; Machado, Olga L. T.; Freire, Denise M. G.

The influence of several factors on the hydrolytic activity of lipase, present in the acetone powder from dormant castor seeds (Ricinus communis) was evaluated. The enzyme showed a marked specificity for short-chain substrates. The best reaction conditions were an acid medium, Triton X-100 as the emulsifying agent and a temperature of 30°C. The lipase activity of the acetone powder of different castor oil genotypes showed great variability and storage stability of up to 90%. The toxicology analysis of the acetone powder from genotype Nordestina BRS 149 showed a higher ricin (toxic component) content, a lower 2S albumin (allergenic compound) content, and similar allergenic potential compared with untreated seeds.

Demonstration of a stabilized alumina/ethanol colloidal dispersion technique for seeding high temperature air flows

NASA Technical Reports Server (NTRS)

Wernet, Mark P.; Skoch, Gary J.; Wernet, Judith H.

1995-01-01

Laser anemometry enables the measurement of complex flow fields via the light scattered from small particles entrained in the flow. In the study of turbomachinery, refractory seed materials are required for seeding the flow due to the high temperatures encountered. In this work we present a pH stabilization technique commonly employed in ceramic processing to obtain stable dispersions for generating aerosols of refractory seed material. By adding submicron alumina particles to a preadjusted pH solution of ethanol, a stable dispersion is obtained which when atomized, produces a high quality aerosol. Commercial grade alumina powder is used with a moderate size distribution. Other metal oxide powders in various polar solvents could also be used once the point of zero charge (pH(pzc)) of the powder in the solvent has been determined. Laser anemometry measurements obtained using the new seeding technique are compared to measurements obtained using Polystyrene Latex (PSL) spheres as the seed material.

Borehole sealing method and apparatus

DOEpatents

Hartley, James N.; Jansen, Jr., George

1977-01-01

A method and apparatus is described for sealing boreholes in the earth. The borehole is blocked at the sealing level, and a sealing apparatus capable of melting rock and earth is positioned in the borehole just above seal level. The apparatus is heated to rock-melting temperature and powdered rock or other sealing material is transported down the borehole to the apparatus where it is melted, pooling on the mechanical block and allowed to cool and solidify, sealing the hole. Any length of the borehole can be sealed by slowly raising the apparatus in the borehole while continuously supplying powdered rock to the apparatus to be melted and added to the top of the column of molten and cooling rock, forming a continuous borehole seal. The sealing apparatus consists of a heater capable of melting rock, including means for supplying power to the heater, means for transporting powdered rock down the borehole to the heater, means for cooling the apparatus and means for positioning the apparatus in the borehole.

Solution of reduced graphene oxide synthesized from coconut shells and its optical properties

NASA Astrophysics Data System (ADS)

Mas'udah, Kusuma Wardhani; Nugraha, I. Made Ananta; Abidin, Saiful; Mufid, Ali; Astuti, Fahmi; Darminto

2016-04-01

Reduced graphene oxide (r-GO)powder has been prepared from coconut shells by carbonization process at 400°C for 3, 4 and 5 hours.Theresulted sample mass was reduced to be 60% relativelycompared to the starting material. The longer heating duration has also led to the rGO with reduced crystalinity according to the X-ray diffractometry data and TEM. The rGO solution was prepared by adding powders of 5, 10 and 15 grams into 50 ml destiled water and then centrifused at 6000 rpm for 30 minutes.The resulted solutions were seen to be varied form clear transparant, light and dark yellow to black. Measurement using particle size analyser shows that the individual rGO particles tends to be agglomerating each others to form bigger size clustering, manifested by the observed bigger size particles for the increasing amount of soluted rGO powders in water.The varying UV-visible spectra of these rGO solutions together with their optical bandgaps will also be discussed in this study.

Experimental investigation of amount of nano-Al2O3 on mechanical properties of Al-based nano-composites fabricated by powder metallurgy (PM)

NASA Astrophysics Data System (ADS)

Razzaqi, A.; Liaghat, Gh.; Razmkhah, O.

2017-10-01

In this paper, mechanical properties of Aluminum (Al) matrix nano-composites, fabricated by Powder Metallurgy (PM) method, has been investigated. Alumina (Al2O3) nano particles were added in amounts of 0, 2.5, 5, 7.5 and 10 weight percentages (wt%). For this purpose, Al powder (particle size: 20 µm) and nano-Al2O3 (particle size: 20 nm) in various weight percentages were mixed and milled in a blade mixer for 15 minutes in 1500 rpm. Then, the obtained mixture, compacted by means of a two piece die and uniaxial cold press of about 600 MPa and cold iso-static press (CIP), required for different tests. After that, the samples sintered in 600°C for 90 minutes. Compression and three-point bending tests performed on samples and the results, led us to obtain the optimized particle size for achieving best mechanical properties.

Conventional and two step sintering of PZT-PCN ceramics

NASA Astrophysics Data System (ADS)

Keshavarzi, Mostafa; Rahmani, Hooman; Nemati, Ali; Hashemi, Mahdieh

2018-02-01

In this study, PZT-PCN ceramic was made via sol-gel seeding method and effects of conventional sintering (CS) as well as two-step sintering (TSS) were investigated on microstructure, phase formation, density, dielectric and piezoelectric properties. First, high quality powder was achieved by seeding method in which the mixture of Co3O4 and Nb2O5 powder was added to the prepared PZT sol to form PZT-PCN gel. After drying and calcination, pyrochlore free PZT-PCN powder was synthesized. Second, CS and TSS were applied to achieve dense ceramic. The optimum temperature used for 2 h of conventional sintering was obtained at 1150 °C; finally, undesired ZrO2 phase formed in CS procedure was removed successfully with TSS procedure and dielectric and piezoelectric properties were improved compared to the CS procedure. The best electrical properties obtained for the sample sintered by TSS in the initial temperature of T 1 = 1200 °C and secondary temperature of T 2 = 1000 °C for 12 h.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ay, H.; Özyurek, D.; Yıldırım, M., E-mail: musayildirim@karabuk.edu.tr

In this study, the wear properties of in-situ 7075 Al-Ti composites produced by powder metallurgy route were investigated. Different amount of Ti (2, 4, 6 %) added to gas atomized 7075 Al alloy powders and they were mixed in turbula with 47rpm for 45 minutes. Then the mixed powders were pre-shaped by press under 600 MPa pressure. The samples were cooled in the furnace after sintered at 580 °C for 4 hours in the atmosphere controlled furnace. Standard metallographic process such as grinding, polishing and etching were applied to sintered samples. The hardness values were measured. Scanning Electron Microscope (SEM), X-Raymore » Diffraction (XRD) examines were carried out. The wear tests were performed in a pin-on disc type wear apparatus with 1 ms{sup −1} sliding speed at six different sliding distance (500-3000 m) under 30 N loads. As a result of studies, hardness values were increased with increasing Ti content, in addition the weight losses were decreased with increasing Ti amount.« less

Effects of mixing technique on bubble formation in alginate impression material.

PubMed

McDaniel, Thomas F; Kramer, Robert T; Im, Francis; Snow, Dallin

2013-01-01

Previous studies have found that variations in mixing technique can influence the porosity content of alginate impression material. The aim of this study was twofold: determine whether bubble formation in alginate is influenced by the sequence of water/powder addition prior to mixing, and to compare 4 different mixing techniques. Manual spatulation, an automated spinning bowl, a centrifugal mixer and a vacuum mixer were evaluated for the resulting porosity in the set alginate. It was found that adding powder first, versus water first, made no difference in the bubble content using the 3 automated mixing techniques (P = 0.714). However, porosity was significantly less for powder-first trials using manual spatulation (P < 0.05). It was also found that surface porosity in the resulting impressions was significantly less for centrifugal and vacuum mixing when compared to manual spatulation, while internal porosity was significantly less for centrifugal mixing compared to all other mixing techniques (P < 0.05). The centrifugal mixing and vacuum mixing techniques required the least amount of mixing time.

Nitrogen doped microporous carbon by ZnCl2 activation of protein

NASA Astrophysics Data System (ADS)

Wilson, Praveen; Vijayan, Sujith; Prabhakaran, K.

2017-09-01

ZnCl2 activation of protein containing biomass has been studied for the preparation of N-doped activated carbon (NDC) using powdered dry fish as a source of protein. Nearly 52% increase in the yield of NDC is observed by activation with ZnCl2 due to an increase in the thermal stability of Zn2+-fish protein complex compared to the protein alone. The NDCs obtained are characterized by XRD, IR, XPS, Raman spectroscopy, SEM, TEM, elemental analysis and N2 adsorption-desorption studies. The activation at 550 °C produces NDC with the highest surface area and total pore volume of 1001 m2 g-1 and 0.719 cm3 g-1, respectively, at a ZnCl2 to fish powder weight ratio of 3. A maximum micropore volume of 0.273 cm3 g-1 is obtained at a ZnCl2 to fish powder weight ratio of 1:1. The N-content (12.4-5.2 wt%) decreases with an increase in activation temperature and ZnCl2 to fish powder weight ratio. The NDC obtained by activation at 550 °C at a ZnCl2 to fish powder weight ratio of 1:1 shows the maximum CO2 adsorption capacity of 2.4 and 3.73 mmol g-1 at 25 and 0 °C, respectively, at 1 atmosphere. The CO2 adsorption on the NDC shows excellent cyclic stability and high selectivity over nitrogen gas.

Calibration and testing of a Raman hyperspectral imaging system to reveal powdered food adulteration

PubMed Central

Lohumi, Santosh; Lee, Hoonsoo; Kim, Moon S.; Qin, Jianwei; Kandpal, Lalit Mohan; Bae, Hyungjin; Rahman, Anisur

2018-01-01

The potential adulteration of foodstuffs has led to increasing concern regarding food safety and security, in particular for powdered food products where cheap ground materials or hazardous chemicals can be added to increase the quantity of powder or to obtain the desired aesthetic quality. Due to the resulting potential health threat to consumers, the development of a fast, label-free, and non-invasive technique for the detection of adulteration over a wide range of food products is necessary. We therefore report the development of a rapid Raman hyperspectral imaging technique for the detection of food adulteration and for authenticity analysis. The Raman hyperspectral imaging system comprises of a custom designed laser illumination system, sensing module, and a software interface. Laser illumination system generates a 785 nm laser line of high power, and the Gaussian like intensity distribution of laser beam is shaped by incorporating an engineered diffuser. The sensing module utilize Rayleigh filters, imaging spectrometer, and detector for collection of the Raman scattering signals along the laser line. A custom-built software to acquire Raman hyperspectral images which also facilitate the real time visualization of Raman chemical images of scanned samples. The developed system was employed for the simultaneous detection of Sudan dye and Congo red dye adulteration in paprika powder, and benzoyl peroxide and alloxan monohydrate adulteration in wheat flour at six different concentrations (w/w) from 0.05 to 1%. The collected Raman imaging data of the adulterated samples were analyzed to visualize and detect the adulterant concentrations by generating a binary image for each individual adulterant material. The results obtained based on the Raman chemical images of adulterants showed a strong correlation (R>0.98) between added and pixel based calculated concentration of adulterant materials. This developed Raman imaging system thus, can be considered as a powerful analytical technique for the quality and authenticity analysis of food products. PMID:29708973

Calibration and testing of a Raman hyperspectral imaging system to reveal powdered food adulteration.

PubMed

Lohumi, Santosh; Lee, Hoonsoo; Kim, Moon S; Qin, Jianwei; Kandpal, Lalit Mohan; Bae, Hyungjin; Rahman, Anisur; Cho, Byoung-Kwan

2018-01-01

The potential adulteration of foodstuffs has led to increasing concern regarding food safety and security, in particular for powdered food products where cheap ground materials or hazardous chemicals can be added to increase the quantity of powder or to obtain the desired aesthetic quality. Due to the resulting potential health threat to consumers, the development of a fast, label-free, and non-invasive technique for the detection of adulteration over a wide range of food products is necessary. We therefore report the development of a rapid Raman hyperspectral imaging technique for the detection of food adulteration and for authenticity analysis. The Raman hyperspectral imaging system comprises of a custom designed laser illumination system, sensing module, and a software interface. Laser illumination system generates a 785 nm laser line of high power, and the Gaussian like intensity distribution of laser beam is shaped by incorporating an engineered diffuser. The sensing module utilize Rayleigh filters, imaging spectrometer, and detector for collection of the Raman scattering signals along the laser line. A custom-built software to acquire Raman hyperspectral images which also facilitate the real time visualization of Raman chemical images of scanned samples. The developed system was employed for the simultaneous detection of Sudan dye and Congo red dye adulteration in paprika powder, and benzoyl peroxide and alloxan monohydrate adulteration in wheat flour at six different concentrations (w/w) from 0.05 to 1%. The collected Raman imaging data of the adulterated samples were analyzed to visualize and detect the adulterant concentrations by generating a binary image for each individual adulterant material. The results obtained based on the Raman chemical images of adulterants showed a strong correlation (R>0.98) between added and pixel based calculated concentration of adulterant materials. This developed Raman imaging system thus, can be considered as a powerful analytical technique for the quality and authenticity analysis of food products.

Effects of Dentin Debris on the Antimicrobial Properties of Sodium Hypochlorite and Etidronic Acid.

PubMed

Arias-Moliz, Maria Teresa; Morago, Ana; Ordinola-Zapata, Ronald; Ferrer-Luque, Carmen María; Ruiz-Linares, Matilde; Baca, Pilar

2016-05-01

The purpose of this study was to determine the influence of dentin powder on the concentration, pH, and antimicrobial activity of sodium hypochlorite (NaOCl) alone and combined with etidronic acid (HEBP). Biofilms of Enterococcus faecalis were grown on the surface of dentin blocks for 5 days and then exposed to 1% and 2.5% NaOCl alone or combined with 9% HEBP for 3 minutes in the absence and presence of dentin powder. The biovolumes of the biofilm were measured using confocal microscopy and the live/dead technique. The available chlorine and pH of the solutions were also measured. Nonparametric tests were used to determine statistical differences (P < .05). The presence of dentin powder resulted in a reduction of the free available chlorine and pH in all the irrigating solutions; 1% NaOCl lost its antimicrobial activity completely in the presence of dentin powder. The antimicrobial activity was significantly reduced in the 2.5% NaOCl and 1% NaOCl/HEBP groups, and it was not affected in the 2.5% NaOCl/HEBP group. The presence of dentin powder significantly decreased the available chlorine and antimicrobial activity of 1% NaOCl, 2.5% NaOCl, and 1% NaOCl/HEBP irrigating solutions. The antimicrobial activity of 2.5% NaOCl/HEBP was not affected by the dentin powder after a 3-minute contact time against E. faecalis biofilms. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Powder-driven-nail connections for round timber

Treesearch

Ronald W. Wolfe; KugBo Shim; Marshall Begel

2003-01-01

In an effort to encourage the development of value-added engineered applications for small diameter round timber, research is being conducted at the US Forest Products Laboratory to develop and verify design guidelines for connections with specific application to round timbers. The objective of this work is to provide potential users with a number of viable connection...

Using Goat's Milk, Barley Flour, Honey, and Probiotic to Manufacture of Functional Dairy Product.

PubMed

Ismail, Magdy Mohamed; Hamad, Mohamed Farid; Elraghy, Esraa Mohamed

2017-08-23

Stirred yogurt manufactured using probiotic culture which usually called Rayeb milk in the Middle East region is one of the most important functional fermented milk products. To increase the health and functionality properties to this product, some ingredients like fruits, cereal, and whey protein are used in production. This study was carried out to prepare functional Rayeb milk from goat's milk, barley flour (15%) and honey (4%) mixtures using ABT culture. Also, vanilla and cocoa powder were used as flavorings. Adding barley flour and honey to goat's milk increased curd tension and water-holding capacity and decreased coagulation time and susceptibility to syneresis. The values of carbohydrate, total solids, dietary fiber, ash, total protein, water soluble nitrogen, total volatile fatty acids, unsaturated fatty acids, oleic, linoleic, α-linolenic acids, and antioxidant activity were higher in Rayeb milk supplemented with barley flour and honey than control. The viabilities of Lactobacillus acidophilus and Bifidobacterium lactis Bb12 (Chr. Hansen's Lab A/S) increased in fortified Rayeb milk. The recommended level of 10 7  cfu g -1 of bifidobacteria as a probiotic was exceeded for these samples. Addition of vanilla (0.1%) or cocoa powder (0.5%) improved the sensory properties of fortified Rayeb milk.

Antioxidant activities of two sericin proteins extracted from cocoon of silkworm (Bombyx mori) measured by DPPH, chemiluminescence, ORAC and ESR methods.

PubMed

Takechi, Tayori; Wada, Ritsuko; Fukuda, Tsubasa; Harada, Kazuki; Takamura, Hitoshi

2014-05-01

Recent efforts have focused on the use of sericin proteins extracted from cocoons of silkworm as a healthy food source for human consumption. In this study, we focused on the antioxidative properties of sericin proteins. The antioxidative properties were measured in sericin proteins extracted from the shell of the cocoon, designated hereafter as white sericin protein and yellow-green sericin protein, as well as bread without sericin protein and bread to which white sericin powder had been added using four measurement methods: 1,1-Diphenyl-2-picrylhydrazyl (DPPH), chemiluminescence, oxygen radical absorbance capacity (ORAC) and electron spin resonance (ESR). High antioxidative properties of sericin proteins were indicated by all four methods. A comparison of the two types of sericin proteins revealed that yellow-green sericin protein exhibited high antioxidative properties as indicated by the DPPH, chemiluminescence and ORAC methods. By contrast, a higher antioxidative property was determined in white sericin protein by the ESR method. Consequently, our findings confirmed that sericin proteins have antioxidative properties against multiple radicals. In addition, the antioxidative property of bread was enhanced by the addition of sericin powder to the bread. Therefore, findings of this study suggest that sericin proteins may be efficiently used as beneficial food for human health.

Antioxidant activities of two sericin proteins extracted from cocoon of silkworm (Bombyx mori) measured by DPPH, chemiluminescence, ORAC and ESR methods

PubMed Central

TAKECHI, TAYORI; WADA, RITSUKO; FUKUDA, TSUBASA; HARADA, KAZUKI; TAKAMURA, HITOSHI

2014-01-01

Recent efforts have focused on the use of sericin proteins extracted from cocoons of silkworm as a healthy food source for human consumption. In this study, we focused on the antioxidative properties of sericin proteins. The antioxidative properties were measured in sericin proteins extracted from the shell of the cocoon, designated hereafter as white sericin protein and yellow-green sericin protein, as well as bread without sericin protein and bread to which white sericin powder had been added using four measurement methods: 1,1-Diphenyl-2-picrylhydrazyl (DPPH), chemiluminescence, oxygen radical absorbance capacity (ORAC) and electron spin resonance (ESR). High antioxidative properties of sericin proteins were indicated by all four methods. A comparison of the two types of sericin proteins revealed that yellow-green sericin protein exhibited high antioxidative properties as indicated by the DPPH, chemiluminescence and ORAC methods. By contrast, a higher antioxidative property was determined in white sericin protein by the ESR method. Consequently, our findings confirmed that sericin proteins have antioxidative properties against multiple radicals. In addition, the antioxidative property of bread was enhanced by the addition of sericin powder to the bread. Therefore, findings of this study suggest that sericin proteins may be efficiently used as beneficial food for human health. PMID:24748975

Brown seaweed (Saccharina japonica) as an edible natural delivery matrix for allyl isothiocyanate inhibiting food-borne bacteria.

PubMed

Siahaan, Evi Amelia; Pendleton, Phillip; Woo, Hee-Chul; Chun, Byung-Soo

2014-01-01

The edible, brown seaweed Saccharina japonica was prepared as powder in the size range 500-900 μm for the desorption release of allyl isothiocyanate (AITC). Powders were used as raw (containing lipids) and as de-oiled, where the lipid was removed. In general, de-oiled powders adsorbed larger masses of AITC after vapour or solution contact. Mass adsorbed due to solution contact exceeded vapour contact. Larger particles adsorbed more than smaller particles. No chemical bonding between AITC and the powder surface occurred. Release from vapour deposited particles reached 70-85% available within 72 h; solution deposited reached 70-90% available at 192 h. The larger amounts of AITC adsorbed via solution deposition resulted in greater vapour-phase concentrations at 72 h for antimicrobial activity studies. No loss of activity was detected against Escherichia coli, Salmonella Typhimurium or Bacillus cereus. Only a nominal activity against Staphylococcus aureus was demonstrated. S. japonica powder could be used as an edible, natural vehicle for AITC delivery. Copyright © 2013 Elsevier Ltd. All rights reserved.

Demystifying Mystery Powders.

ERIC Educational Resources Information Center

Kotar, Michael

1989-01-01

Describes science activities which use simple chemical tests to distinguish between materials and to determine some of their properties. Explains the water, iodine, heat, acid, baking soda, acid/base indicator, glucose, and sugar tests. Includes activities to enhance chemical testing and a list of suggested powders for use. (RT)

Effect of drying parameters on physiochemical and sensory properties of fruit powders processed by PGSS-, Vacuum- and Spray-drying.

PubMed

Feguš, Urban; Žigon, Uroš; Petermann, Marcus; Knez, Željko

2015-01-01

Aim of this experimental work was to investigate the possibility of producing fruit powders without employing drying aid and to investigate the effect of drying temperatures on the final powder characteristics. Raw fruit materials (banana puree, strawberry puree and blueberry concentrate) were processed using three different drying techniques each operating at a different temperature conditions: vacuum-drying (-27-17 °C), Spray-drying (130-160 °C) and PGSS-drying (112-152 °C). Moisture content, total colour difference, antioxidant activity and sensory characteristics of the processed fruit powders were analysed. The results obtained from the experimental work indicate that investigated fruit powders without or with minimal addition of maltodextrin can be produced. Additionally, it was observed that an increase in process temperature results in a higher loss of colour, antioxidant activity and intensity of the flavour profile.

Enhanced coal-dependent methanogenesis coupled with algal biofuels: Potential water recycle and carbon capture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnhart, Elliott P.; Davis, Katherine J.; Varonka, Matthew

Many coal beds contain microbial communities that can convert coal to natural gas (coalbed methane). Native microorganisms were obtained from Powder River Basin (PRB) coal seams with a diffusive microbial sampler placed downhole and used as an inoculum for enrichments with different nutrients to investigate microbially-enhanced coalbed methane production (MECoM). Coal-dependent methanogenesis more than doubled when yeast extract (YE) and several less complex components (proteins and amino acids) were added to the laboratory microcosms. Stimulated coal-dependent methanogenesis with peptone was 86% of that with YE while glutamate-stimulated activity was 65% of that with YE, and a vitamin mix had onlymore » 33% of the YE stimulated activity. For field application of MECoM, there is interest in identifying cost-effective alternatives to YE and other expensive nutrients. In laboratory studies, adding algal extract (AE) with lipids removed stimulated coal-dependent methanogenesis and the activity was 60% of that with YE at 27 d and almost 90% of YE activity at 1406 d. Analysis of British Thermal Unit (BTU) content of coal (a measure of potential energy yield) from long-term incubations indicated > 99.5% of BTU content remained after coalbed methane (CBM) stimulation with either AE or YE. Thus, the coal resource remains largely unchanged following stimulated microbial methane production. Algal CBM stimulation could lead to technologies that utilize coupled biological systems (photosynthesis and methane production) that sustainably enhance CBM production and generate algal biofuels while also sequestering carbon dioxide (CO 2).« less

Enhanced coal-dependent methanogenesis coupled with algal biofuels: Potential water recycle and carbon capture

DOE PAGES

Barnhart, Elliott P.; Davis, Katherine J.; Varonka, Matthew; ...

2017-01-05

Many coal beds contain microbial communities that can convert coal to natural gas (coalbed methane). Native microorganisms were obtained from Powder River Basin (PRB) coal seams with a diffusive microbial sampler placed downhole and used as an inoculum for enrichments with different nutrients to investigate microbially-enhanced coalbed methane production (MECoM). Coal-dependent methanogenesis more than doubled when yeast extract (YE) and several less complex components (proteins and amino acids) were added to the laboratory microcosms. Stimulated coal-dependent methanogenesis with peptone was 86% of that with YE while glutamate-stimulated activity was 65% of that with YE, and a vitamin mix had onlymore » 33% of the YE stimulated activity. For field application of MECoM, there is interest in identifying cost-effective alternatives to YE and other expensive nutrients. In laboratory studies, adding algal extract (AE) with lipids removed stimulated coal-dependent methanogenesis and the activity was 60% of that with YE at 27 d and almost 90% of YE activity at 1406 d. Analysis of British Thermal Unit (BTU) content of coal (a measure of potential energy yield) from long-term incubations indicated > 99.5% of BTU content remained after coalbed methane (CBM) stimulation with either AE or YE. Thus, the coal resource remains largely unchanged following stimulated microbial methane production. Algal CBM stimulation could lead to technologies that utilize coupled biological systems (photosynthesis and methane production) that sustainably enhance CBM production and generate algal biofuels while also sequestering carbon dioxide (CO 2).« less

Evaluation of Antioxidative Activity of Various Levels of Ethanol Extracted Tomato Powder and Application to Pork Patties.

PubMed

Kim, Hyeong Sang; Chin, Koo Bok

2017-01-01

This study was performed to evaluate antioxidant activity of tomato powder extracted by various concentrations of ethanol (0, 25, 50, 75, 100%) and to evaluate the physicochemical properties and antioxidant activities of pork patties with ethanol extracted tomato (EET) powder. No differences in the contents of total of individual phenolic compounds including gallic acid and catechin, were observed among the treatments ( p >0.05). Among the various concentrations, 50% and 75% EET powder showed the highest free radical scavenging and iron chelating activities ( p <0.05). Lipid peroxidation was retarded in linoleic acid emulsion with the addition of 50% and 75% EET powder (0.1%). Based on the model study, five pork patties were actually manufactured; control patty, reference patty with 0.01% of butylated hydroxytoluene, patty with 1% of water extracted tomato (WET), and patties with 0.5 and 1.0% of EET. Addition of 1% WET and EET decreased pH value, and increased redness values of pork patties, as compared to the control ( p <0.05). Pork patties with WET (1.0%) and EET (0.5% and 1.0%) had lower 2-thiobarbituric acid reactive substances values compared with control patties after 7 d of storage ( p <0.05). Pork patties containing EET powder showed lower total bacterial and Enterobacteriaceae counts than control patties ( p <0.05). In conclusion, WET and EET (50%) could be used as a natural antioxidant and antimicrobial agent in meat products.

Sol-Gel Process for Making Pt-Ru Fuel-Cell Catalysts

NASA Technical Reports Server (NTRS)

Narayanan, Sekharipuram; Valdez, Thomas; Kumta, Prashant; Kim, Y.

2005-01-01

A sol-gel process has been developed as a superior alternative to a prior process for making platinum-ruthenium alloy catalysts for electro-oxidation of methanol in fuel cells. The starting materials in the prior process are chloride salts of platinum and ruthenium. The process involves multiple steps, is time-consuming, and yields a Pt-Ru product that has relatively low specific surface area and contains some chloride residue. Low specific surface area translates to incomplete utilization of the catalytic activity that might otherwise be available, while chloride residue further reduces catalytic activity ("poisons" the catalyst). In contrast, the sol-gel process involves fewer steps and less time, does not leave chloride residue, and yields a product of greater specific area and, hence, greater catalytic activity. In this sol-gel process (see figure), the starting materials are platinum(II) acetylacetonate [Pt(C5H7O2)2, also denoted Pt-acac] and ruthenium(III) acetylacetonate [Ru(C5H7O2)3, also denoted Ru-acac]. First, Pt-acac and Ru-acac are dissolved in acetone at the desired concentrations (typically, 0.00338 moles of each salt per 100 mL of acetone) at a temperature of 50 C. A solution of 25 percent tetramethylammonium hydroxide [(CH3)4NOH, also denoted TMAH] in methanol is added to the Pt-acac/Ruacac/ acetone solution to act as a high-molecular-weight hydrolyzing agent. The addition of the TMAH counteracts the undesired tendency of Pt-acac and Ru-acac to precipitate as separate phases during the subsequent evaporation of the solvent, thereby helping to yield a desired homogeneous amorphous gel. The solution is stirred for 10 minutes, then the solvent is evaporated until the solution becomes viscous, eventually transforming into a gel. The viscous gel is dried in air at a temperature of 170 C for about 10 hours. The dried gel is crushed to make a powder that is the immediate precursor of the final catalytic product. The precursor powder is converted to the final product in a controlled-atmosphere heat treatment. Desirably, the final product is a phase-pure (Pt phase only) Pt-Ru powder with a high specific surface area. The conditions of the controlled- atmosphere heat are critical for obtaining the aforementioned desired properties. A typical heat treatment that yields best results for a catalytic alloy of equimolar amounts of Pt and Ru consists of at least two cycles of heating to a temperature of 300 C and holding at 300 C for several hours, all carried out in an atmosphere of 1 percent O2 and 99 percent N2. The resulting powder consists of crystallites with typical linear dimensions of <10 nm. Tests have shown that the powder is highly effective in catalyzing the electro-oxidation of methanol.

Rational Selection of Tailored Amendment Mixtures and Composites for In Situ Remediation of Contaminated Sediments

DTIC Science & Technology

2008-12-01

Certification Program GAC granular activated carbon HGR sulfur impregnated activated carbon MCA Menzie Cura and Associates MRM Minimum Required...determination of iodine number was followed. The materials tested were granular activated carbon (GAC), alumina powder, ATS, apatite, bentonite, barite...materials tested were granular activated carbon (GAC), alumina powder, ATS, apatite, bentonite, barite, ConSep 20 and 42%, and ATC. The Iodine Number

Cerebroprotective Actions of Triticum aestivum Linn Powder and Bauhinia purpurea Flower Powder in Surgically Induced Cerebral Infraction in Rats.

PubMed

Annapurna, Akula; Vishala, Thonangi C; Bitra, Veera R; Rapaka, Deepthi; Shaik, Asmath

2018-01-01

The prime objective of this study is to evaluate the cerebroprotective actions of Triticum aestivum (wheatgrass) powder and Bauhinia purpurea flower (dev kanchan) powder against the experimentally induced global ischemia reperfusion injury in rats. In the first phase of the studies, 1 h before the surgical procedure, the Wistar rats were orally served with varied doses of wheatgrass powder (5, 10, 30, and 100 μg/kg) and Bauhinia flower powder (30, 100, 200, and 300 μg/kg), respectively. The ischemia was induced by 30-min bilateral carotid artery occlusion in succession to reperfusion for 4 h. It was proved that the wheatgrass powder and Bauhinia flower powder yielded a significant, dose-dependent cerebroprotection in terms of reduction in cerebral infarct size when compared with the control group. Coming to the second phase of the studies, a certain potential dose of 10 μg/kg of wheatgrass and 200 μg/kg of Bauhinia flower powders was selected keeping the protective action in view, and the animals were treated for 15 days. The major findings of the study are that wheatgrass and Bauhinia flower powders significantly augmented the magnitude of the antioxidant enzymes, viz., super oxide dismutase and catalase, and further reduced the levels of lipid peroxidation. The present study clearly showed that the wheatgrass powder and Bauhinia flower powder possess significant antioxidant properties that may act as a key ingredient in various ayurvedic preparations for the treatment of various diseases like cerebral ischemic reperfusion injury. The wheat grass contains high amount of bioflavonoids, alkaloids, SOD etc which are responsible for anti oxidant activity.The Bauhinia purpurea contains glycosides, flavonoids and also plays a major role in DPPH activity which is responsible for anti oxidant activity.The wheat grass (10 mg/kg) and bauhinia (200 mg/kg) significantly(P < 0.0001) reduced the percentage of infract size when compared to Ischemia reperfusion control group.The wheat grass (10 mg/kg) and bauhinia (200 mg/kg) significantly (P <0.0001) reduced the lipid peroxidation (MDA) and increased SOD and Catalase. Abbreviations used: BCAO: Bilateral Carotid Artery Occlusion, MCA: middle cerebral artery, ROS: reactive oxygen species, SCMC: Sodium carboxy methyl cellulose, p.o: Per oral route, T.T.C: Triphenyl tetrazolium chloride, MDA: Malondialdehyde, SOD: Super oxide dismutase.

Cerebroprotective Actions of Triticum aestivum Linn Powder and Bauhinia purpurea Flower Powder in Surgically Induced Cerebral Infraction in Rats

PubMed Central

Annapurna, Akula; Vishala, Thonangi C.; Bitra, Veera R.; Rapaka, Deepthi; Shaik, Asmath

2017-01-01

Objective: The prime objective of this study is to evaluate the cerebroprotective actions of Triticum aestivum (wheatgrass) powder and Bauhinia purpurea flower (dev kanchan) powder against the experimentally induced global ischemia reperfusion injury in rats. Materials and Methods: In the first phase of the studies, 1 h before the surgical procedure, the Wistar rats were orally served with varied doses of wheatgrass powder (5, 10, 30, and 100 μg/kg) and Bauhinia flower powder (30, 100, 200, and 300 μg/kg), respectively. The ischemia was induced by 30-min bilateral carotid artery occlusion in succession to reperfusion for 4 h. It was proved that the wheatgrass powder and Bauhinia flower powder yielded a significant, dose-dependent cerebroprotection in terms of reduction in cerebral infarct size when compared with the control group. Coming to the second phase of the studies, a certain potential dose of 10 μg/kg of wheatgrass and 200 μg/kg of Bauhinia flower powders was selected keeping the protective action in view, and the animals were treated for 15 days. Results: The major findings of the study are that wheatgrass and Bauhinia flower powders significantly augmented the magnitude of the antioxidant enzymes, viz., super oxide dismutase and catalase, and further reduced the levels of lipid peroxidation. Conclusions: The present study clearly showed that the wheatgrass powder and Bauhinia flower powder possess significant antioxidant properties that may act as a key ingredient in various ayurvedic preparations for the treatment of various diseases like cerebral ischemic reperfusion injury. SUMMARY The wheat grass contains high amount of bioflavonoids, alkaloids, SOD etc which are responsible for anti oxidant activity.The Bauhinia purpurea contains glycosides, flavonoids and also plays a major role in DPPH activity which is responsible for anti oxidant activity.The wheat grass (10 mg/kg) and bauhinia (200 mg/kg) significantly(P < 0.0001) reduced the percentage of infract size when compared to Ischemia reperfusion control group.The wheat grass (10 mg/kg) and bauhinia (200 mg/kg) significantly (P <0.0001) reduced the lipid peroxidation (MDA) and increased SOD and Catalase. Abbreviations used: BCAO: Bilateral Carotid Artery Occlusion, MCA: middle cerebral artery, ROS: reactive oxygen species, SCMC: Sodium carboxy methyl cellulose, p.o: Per oral route, T.T.C: Triphenyl tetrazolium chloride, MDA: Malondialdehyde, SOD: Super oxide dismutase. PMID:29491626

Relating dynamic perception of reformulated cheese pies to consumers' expectations of satiating ability.

PubMed

Marcano, J; Varela, P; Cunha, L M; Fiszman, S

2015-12-01

Designing satiating food is not an easy task. Food reformulation is normally done by altering the proportion of basic ingredients or by adding new minor ingredients. In general, the texture varies concomitantly with these changes, altering the way the food is processed orally and the complete eating experience. This highlights the interest of discovering how variations in minor ingredients influence texture and how this affects the dynamics of the oral trajectory. Six cheese pie formulations were prepared: basic recipe (Base), no egg (-Egg), no corn starch (-Corn starch) no sugar (-Sugar), added diary cream (+Cream) and extra skimmed milk powder (+Milk powder). Temporal dominance of sensations was used to show that the appearance and disappearance of each texture sensation dominance experienced in the mouth during the eating process differed among the six pies, as did their relation to the consumers' expectation of satiating capacity scores and to the changes in composition. Two extreme behaviors were found: suppression of egg/addition of extra milk powder made the pies initially drier and harder, while suppression of corn starch/addition of cream gave the samples a soft, moist early sensation. The former elicited higher expectations of satiating capacity. In addition, overall liking, liking evolving with time (dynamic liking) and the level of several key texture attributes' divergence from those of an "ideal" cheese pie were evaluated on bipolar just-about-right scales and through penalty analysis to gain insights into potential directions for reformulating acceptable pies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Improved Photo-Ignition of Carbon Nanotubes/Ferrocene Using a Lipophilic Porphyrin under White Power LED Irradiation

PubMed Central

Primiceri, Patrizio; de Fazio, Roberto; Carlucci, Antonio Paolo; Mazzetto, Selma Elaine

2018-01-01

The aim of this work is to investigate and characterize the photo-ignition process of dry multi-walled carbon nanotubes (MWCNTs) mixed with ferrocene (FeCp2) powder, using an LED (light-emitting diode) as the light source, a combination that has never been used, to the best of our knowledge. The ignition process was improved by adding a lipophilic porphyrin (H2Pp) in powder to the MWCNTs/FeCp2 mixtures—thus, a lower ignition threshold was obtained. The ignition tests were carried out by employing a continuous emission and a pulsed white LED in two test campaigns. In the first, two MWCNT typologies, high purity (HP) and industrial grade (IG), were used without porphyrin, obtaining, for both, similar ignition thresholds. Furthermore, comparing ignition thresholds obtained with the LED source with those previously obtained with a Xenon (Xe) lamp, a significant reduction was observed. In the second test campaign, ignition tests were carried out by means of a properly driven and controlled pulsed XHP70 LED source. The minimum ignition energy (MIE) of IG-MWCNTs/FeCp2 samples was determined by varying the duration of the light pulse. Experimental results show that ignition is obtained with a pulse duration of 110 ms and a MIE density of 266 mJ/cm2. The significant reduction of the MIE value (10–40%), observed when H2Pp in powder form was added to the MWCNTs/FeCp2 mixtures, was ascribed to the improved photoexcitation and charge transfer properties of the lipophilic porphyrin molecules. PMID:29342878

Improved Photo-Ignition of Carbon Nanotubes/Ferrocene Using a Lipophilic Porphyrin under White Power LED Irradiation.

PubMed

Visconti, Paolo; Primiceri, Patrizio; de Fazio, Roberto; Carlucci, Antonio Paolo; Mazzetto, Selma Elaine; Mele, Giuseppe

2018-01-13

The aim of this work is to investigate and characterize the photo-ignition process of dry multi-walled carbon nanotubes (MWCNTs) mixed with ferrocene (FeCp₂) powder, using an LED (light-emitting diode) as the light source, a combination that has never been used, to the best of our knowledge. The ignition process was improved by adding a lipophilic porphyrin (H₂Pp) in powder to the MWCNTs/FeCp₂ mixtures-thus, a lower ignition threshold was obtained. The ignition tests were carried out by employing a continuous emission and a pulsed white LED in two test campaigns. In the first, two MWCNT typologies, high purity (HP) and industrial grade (IG), were used without porphyrin, obtaining, for both, similar ignition thresholds. Furthermore, comparing ignition thresholds obtained with the LED source with those previously obtained with a Xenon (Xe) lamp, a significant reduction was observed. In the second test campaign, ignition tests were carried out by means of a properly driven and controlled pulsed XHP70 LED source. The minimum ignition energy (MIE) of IG-MWCNTs/FeCp₂ samples was determined by varying the duration of the light pulse. Experimental results show that ignition is obtained with a pulse duration of 110 ms and a MIE density of 266 mJ/cm². The significant reduction of the MIE value (10-40%), observed when H₂Pp in powder form was added to the MWCNTs/FeCp₂ mixtures, was ascribed to the improved photoexcitation and charge transfer properties of the lipophilic porphyrin molecules.

Method for manufacturing whisker preforms and composites

DOEpatents

Lessing, Paul A.

1995-01-01

A process for manufacturing Si.sub.3 N.sub.4 /SiAlON whiskers by mixing silicon carbide powder with aluminum nitride powder, adding impurities such as calcium oxide or potassium chloride to control whisker characteristics, forming the mixture in a boron nitrogen mold of desired shaped and hot isostatically pressing the formed mixture in a nitrogen environment to produce whiskers comprised substantially of SiAlON at the nucleating end of the whisker and Si.sub.3 N.sub.4 at the other end of the whisker. In one embodiment, reinforced composites are formed by impregnating the Si.sub.3 N.sub.4 /SiAlON whisker preform with a matrix material such as resin binders, liquid metals, intermetallics or ceramic materials.

High-strength, creep-resistant molybdenum alloy and process for producing the same

DOEpatents

Bianco, R.; Buckman, R.W. Jr.; Geller, C.B.

1999-02-09

A wet-doping process for producing an oxide-dispersion strengthened (ODS), creep-resistant molybdenum alloy is disclosed. The alloy is made by adding nitrate or acetate salts of lanthanum, cerium, thorium, or yttrium to molybdenum oxide to produce a slurry, heating the slurry in a hydrogen atmosphere to produce a powder, mixing and cold isostatically pressing the powder, sintering in a hydrogen atmosphere, and thermomechanically processing (swaging, extruding, cold drawing) the product. The ODS molybdenum alloy produced by the process contains 2--4% by volume (ca. 1--4% by weight) of an oxide of lanthanum, cerium, thorium, or yttrium. The alloy has high strength and improved creep-resistance at temperatures greater than 0.55T{sub m} of molybdenum. 10 figs.

High-strength, creep-resistant molybdenum alloy and process for producing the same

DOEpatents

Bianco, Robert; Buckman, Jr., R. William; Geller, Clint B.

1999-01-01

A wet-doping process for producing an oxide-dispersion strengthened (ODS), creep-resistant molybdenum alloy is disclosed. The alloy is made by adding nitrate or acetate salts of lanthanum, cerium, thorium, or yttrium to molybdenum oxide to produce a slurry, heating the slurry in a hydrogen atmosphere to produce a powder, mixing and cold isostatically pressing the powder, sintering in a hydrogen atmosphere, and thermomechanically processing (swaging, extruding, cold drawing) the product. The ODS molybdenum alloy produced by the process contains 2-4% by volume (.about.1-4% by weight) of an oxide of lanthanum, cerium, thorium, or yttrium. The alloy has high strength and improved creep-resistance at temperatures greater than 0.55T.sub.m of molybdenum.

Method for manufacturing whisker preforms and composites

DOEpatents

Lessing, P.A.

1995-11-07

A process is disclosed for manufacturing Si{sub 3}N{sub 4}/SiAlON whiskers by mixing silicon carbide powder with aluminum nitride powder, adding impurities such as calcium oxide or potassium chloride to control whisker characteristics, forming the mixture in a boron nitrogen mold of desired shaped and hot isostatically pressing the formed mixture in a nitrogen environment to produce whiskers comprised substantially of SiAlON at the nucleating end of the whisker and Si{sub 3}N{sub 4} at the other end of the whisker. In one embodiment, reinforced composites are formed by impregnating the Si{sub 3}N{sub 4}/SiAlON whisker preform with a matrix material such as resin binders, liquid metals, intermetallics or ceramic materials.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pahl, R. J.; Trott, W. M.; Snedigar, S.

A series of gas gun tests has been performed to examine contributions to energy release from micron-sized and nanometric aluminum powder added to sieved (212-300{mu}m) HMX. In the absence of added metal, 4-mm-thick, low-density (64-68% of theoretical maximum density) pressings of the sieved HMX respond to modest shock loading by developing distinctive reactive waves that exhibit both temporal and mesoscale spatial fluctuations. Parallel tests have been performed on samples containing 10% (by mass) aluminum in two particle sizes: 2-{mu}m and 123-nm mean particle diameter, respectively. The finely dispersed aluminum initially suppresses wave growth from HMX reactions; however, after a visiblemore » induction period, the added metal drives rapid increases in the transmitted wave particle velocity. Wave profile variations as a function of the aluminum particle diameter are discussed.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaneda, Jaime N.; Pahl, Robert J.; Snedigar, Shane

A series of gas gun tests has been performed to examine contributions to energy release from micron-sized and nanometric aluminum powder added to sieved (212-300{micro}m) HMX. In the absence of added metal, 4-mm-thick, low-density (64-68% of theoretical maximum density) pressings of the sieved HMX respond to modest shock loading by developing distinctive reactive waves that exhibit both temporal and mesoscale spatial fluctuations. Parallel tests have been performed on samples containing 10% (by mass) aluminum in two particle sizes: 2-{micro}m and 123-nm mean particle diameter, respectively. The finely dispersed aluminum initially suppresses wave growth from HMX reactions; however, after a visiblemore » induction period, the added metal drives rapid increases in the transmitted wave particle velocity. Wave profile variations as a function of the aluminum particle diameter are discussed.« less

Design, formulation and evaluation of Aloe vera chewing gum

PubMed Central

Aslani, Abolfazl; Ghannadi, Alireza; Raddanipour, Razieh

2015-01-01

Background: Aloe vera has antioxidant, antiinflammatory, healing, antiseptic, anticancer and antidiabetic effects. The aim of the present study was to design and evaluate the formulation of Aloe vera chewing gum with an appropriate taste and quality with the indications for healing oral wounds, such as lichen planus, mouth sores caused by cancer chemotherapy and mouth abscesses as well as reducing mouth dryness caused by chemotherapy. Materials and Methods: In Aloe vera powder, the carbohydrate content was determined according to mannose and phenolic compounds in terms of gallic acid. Aloe vera powder, sugar, liquid glucose, glycerin, sweeteners and different flavors were added to the soft gum bases. In Aloe vera chewing gum formulation, 10% of dried Aloe vera extract entered the gum base. Then the chewing gum was cut into pieces of suitable sizes. Weight uniformity, content uniformity, the organoleptic properties evaluation, releasing the active ingredient in the phosphate buffer (pH, 6.8) and taste evaluation were examined by Latin square method. Results: One gram of Aloe vera powder contained 5.16 ± 0.25 mg/g of phenolic compounds and 104.63 ± 4.72 mg/g of carbohydrates. After making 16 Aloe vera chewing gum formulations, the F16 formulation was selected as the best formulation according to its physicochemical and organoleptic properties. In fact F16 formulation has suitable hardness, lack of adhesion to the tooth and appropriate size and taste; and after 30 min, it released more than 90% of its drug content. Conclusion: After assessments made, the F16 formulation with maltitol, aspartame and sugar sweeteners was selected as the best formulation. Among various flavors used, peppermint flavor which had the most acceptance between consumers was selected. PMID:26605214

Quality and antioxidant properties of breads enriched with dry onion (Allium cepa L.) skin.

PubMed

Gawlik-Dziki, Urszula; Świeca, Michał; Dziki, Dariusz; Baraniak, Barbara; Tomiło, Justyna; Czyż, Jarosław

2013-06-01

The aim of the study was to investigate the effect on the antioxidant properties and sensory value of bread of adding ground onion skin (OS). For a determination of bioaccessibility and bioavailability in vitro the human gastrointestinal tract model was used. OS contained mastication-extractable quercetin (4.6 mg/g). Quercetin from OS was highly bioaccessible during in vitro conditions, but only approximately 4% of quercetin released during simulated digestion was bioavailable in vitro. The antioxidant potential of bread with OS was significantly higher than the activity noted in the control. In particular, OS addition significantly fortificated bread with bioaccessible lipid oxidation preventers and compounds with reducing and chelating abilities. The 2-3% OS addition caused significant improvement of antioxidant abilities (further increases in the OS supplement did not increase the activity of bread). Sensory evaluation showed that replacement of wheat flour in bread with up to 3% OS powder gave satisfactory consumer acceptability. Copyright © 2012 Elsevier Ltd. All rights reserved.

Environmentally friendly ultrosound synthesis and antibacterial activity of cellulose/Ag/AgCl hybrids.

PubMed

Dong, Yan-Yan; Deng, Fu; Zhao, Jin-Jin; He, Jing; Ma, Ming-Guo; Xu, Feng; Sun, Run-Cang

2014-01-01

This study aims to investigate the fabrication and property of cellulose/Ag/AgCl hybrids. In this article, preparation of cellulose/Ag/AgCl hybrids was reported using the cellulose solution, AgNO₃, AlCl₃·6H₂O with ultrasound agitation method. The cellulose solution was synthesized by the dissolution of the microcrystalline cellulose in NaOH/urea aqueous solution. Influences of the experimental parameters of ultrasound treatment time and ultrasonic intermittent on the hybrids were investigated. The phase, microstructure, thermal stability, and morphology of the hybrids were characterized by X-ray powder diffraction (XRD), Fourier transform infrared (FTIR) spectrometry, thermogravimetric analysis (TGA), differential thermal analysis (DTA), and scanning electron microscopy (SEM). Results showed the successful synthesis of cellulose/Ag/AgCl hybrids with good thermal stability. Moreover, the hybrids displayed desirable antimicrobial activities. Compared with other conventional methods, the rapid, green, and environmentally friendly ultrasound agitation method opens a new window to the high value-added applications of biomass. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of silver additive on physicochemical properties of hydroxyapatite applied to reconstructive surgery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhuk, I. V., E-mail: zhukiv1993@mail.ru; Rasskazova, L. A., E-mail: ly-2207@mail.ru; Korotchenko, N. M., E-mail: korotch@mail.ru

The effect of silver adding to hydroxyapatite (HA) in its solubility in physiological solution and biological activity was investigated. Samples of HA containing silver (AgHA) obtained by liquid-phase method in the conditions of microwave exposure. Solubility (C{sub Ca}{sup 2+}·10{sup 3}, mol/l) of the powders AgHA was determined by chemical methods according trilonometric titration of the calcium ions in physiological solution at 25 and 37 °C. To investigate the biological activity of the samples, a series of experiments on the formation of the calcium-phosphate layer on the surface of the SBF-solution at 37 °C for 28 days. Electronic micrographs of samplesmore » taken at the end of each 7 days of the experiment, indicate the formation of calcium-phosphate layer (CPL) in the samples, the kinetics of which is shown as a function of cumulative concentrations of calcium and magnesium ions from time.« less

Livestock air treatment using PVA-coated powdered activated carbon biofilter

USDA-ARS?s Scientific Manuscript database

The efficacy of polyvinyl alcohol (PVA) biofilters was studied using bench-scale biofilters and air from aerobically-treated swine manure. The PVA-coated powdered activated carbon particles showed excellent properties as a biofiltration medium: water holding capacity of 1.39 g H2O/g-dry PVA; wet por...

Fabrication of piezoelectric ceramic fibers by extrusion of Pb(Zr, Ti)O3 powder and Pb(Zr, Ti)O3 sol mixture

NASA Astrophysics Data System (ADS)

Qiu, Jinhao; Tani, Junji; Kobayashi, Yoshimasa; Um, Tae Young; Takahashi, Hirofumi

2003-06-01

In this study, Pb(Zr, Ti)O3 (PZT) piezoelectric ceramic fibers were fabricated by extrusion from a mixture of PZT powder and PZT sol. The added PZT sol in this study played the role of a binder; the sol changed into crystalline PZT during sintering, and removal of additives before sintering was not required. To obtain the required PZT fibers, the sol viscosity adjustment condition, the mixture ratio of powder and sol for fiber extrusion, and the sintering condition for obtaining polycrystalline fibers were investigated. The PZT precursor solution was synthesized from lead acetate trihydrate, zirconium n-propoxide, and titanium isopropoxide by reflux at 120 °C for 3 h with 2-methoxyethanol. The appropriate adjustment of the spinnable sol was achieved by the addition of acetic acid to suppress the hydrolysis reaction and by curing the sol at 80 °C to promote the condensation of the sol. Green fibers with diameters of about 300µm were successfully extruded from the mixture of PZT powder and sol (powder:sol = 5- 8:1, molar ratio). The extruded fibers, sintered at 1200 °C, had a microstructure with 2- 6µm grains and had no pores or cracks. From the results of displacement behavior measurements, the PZT fibers fabricated by firing at 1200 °C in this study were considered to have the desired piezoelectric properties.

Effect of CeO2 on Microstructure and Wear Resistance of TiC Bioinert Coatings on Ti6Al4V Alloy by Laser Cladding

PubMed Central

Wang, Haojun

2017-01-01

To solve the lack of wear resistance of titanium alloys for use in biological applications, various prepared coatings on titanium alloys are often used as wear-resistant materials. In this paper, TiC bioinert coatings were fabricated on Ti6Al4V by laser cladding using mixed TiC and ZrO2 powders as the basic pre-placed materials. A certain amount of CeO2 powder was also added to the pre-placed powders to further improve the properties of the TiC coatings. The effects of CeO2 additive on the phase constituents, microstructures and wear resistance of the TiC coatings were researched in detail. Although the effect of CeO2 on the phase constituents of the coatings was slight, it had a significant effect on the microstructure and wear resistance of the coatings. The crystalline grains in the TiC coatings, observed by a scanning electron microscope (SEM), were refined due to the effect of the CeO2. With the increase of CeO2 additive content in the pre-placed powders, finer and more compact dendrites led to improvement of the micro-hardness and wear resistance of the TiC coatings. Also, 5 wt % content of CeO2 additive in the pre-placed powders was the best choice for improving the wear properties of the TiC coatings. PMID:29301218

Simulation of Powder Layer Deposition in Additive Manufacturing Processes Using the Discrete Element Method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herbold, E. B.; Walton, O.; Homel, M. A.

2015-10-26

This document serves as a final report to a small effort where several improvements were added to a LLNL code GEODYN-­L to develop Discrete Element Method (DEM) algorithms coupled to Lagrangian Finite Element (FE) solvers to investigate powder-­bed formation problems for additive manufacturing. The results from these simulations will be assessed for inclusion as the initial conditions for Direct Metal Laser Sintering (DMLS) simulations performed with ALE3D. The algorithms were written and performed on parallel computing platforms at LLNL. The total funding level was 3-­4 weeks of an FTE split amongst two staff scientists and one post-­doc. The DEM simulationsmore » emulated, as much as was feasible, the physical process of depositing a new layer of powder over a bed of existing powder. The DEM simulations utilized truncated size distributions spanning realistic size ranges with a size distribution profile consistent with realistic sample set. A minimum simulation sample size on the order of 40-­particles square by 10-­particles deep was utilized in these scoping studies in order to evaluate the potential effects of size segregation variation with distance displaced in front of a screed blade. A reasonable method for evaluating the problem was developed and validated. Several simulations were performed to show the viability of the approach. Future investigations will focus on running various simulations investigating powder particle sizing and screen geometries.« less

Process for decomposing lignin in biomass

DOEpatents

Rector, Kirk Davin; Lucas, Marcel; Wagner, Gregory Lawrence; Kimball, David Bryan; Hanson, Susan Kloek

2014-10-28

A mild inexpensive process for treating lignocellulosic biomass involves oxidative delignification of wood using an aqueous solution prepared by dissolving a catalytic amount of manganese (III) acetate into water and adding hydrogen peroxide. Within 4 days and without agitation, the solution was used to convert poplar wood sections into a fine powder-like delignified, cellulose rich materials that included individual wood cells.

Dehydration of berry purees to produce value-added powders of high quality for use in nutritional supplements: year 3

USDA-ARS?s Scientific Manuscript database

In year two of this three year proposal, we were to dry raspberry and blackberry on a freeze dryer located at the WSU pilot plant (Pullman, WA) and the Radiant Zone Dryer (RZD) at Columbia PhytoTechnology, LLC (Dallesport, WA). We instead focused on RZD processing of cranberry and raspberry because ...

Influencing Solvent Miscibility and Aqueous Stability of Aluminum Nanoparticles through Surface Functionalization with Acrylic Monomers (Postprint)

DTIC Science & Technology

2010-08-26

2,2′-azobis(2-methylpropionitrile) (AIBN), and hydroquinone were purchased from Aldrich and used as received unless otherwise noted. Toluene and...and a glass stopper, was charged with nAl powder (1.0 g, 37 mmol) and hydroquinone (0.050 g, 0.45 mmol), which was added as a radical scavenger to

The deep processing of seaweed industrial waste--Influence of several fermentation on seaweed waste of feed

NASA Astrophysics Data System (ADS)

Zhao, Shipeng; Zhang, Shuping

2018-02-01

This paper focuses on several factors on the effects of fermented seaweed feed, and obtains the optimal fermentation process through the analysis of nutrients. Through the experiment we can get, Seaweed waste fermented the best feed when adding 1% of microbial agents and 0.5% of corn powder, fermenting for 15 days.

Highly Porous NiTi with Isotropic Pore Morphology Fabricated by Self-Propagated High-Temperature Synthesis

NASA Astrophysics Data System (ADS)

Hosseini, S. A.; Alizadeh, M.; Ghasemi, A.; Meshkot, M. A.

2013-02-01

Highly porous NiTi with isotropic pore morphology has been successfully produced by self-propagating high-temperature synthesis of elemental Ni/Ti metallic powders. The effects of adding urea and NaCl as temporary pore fillers were investigated on pore morphology, microstructure, chemical composition, and the phase transformation temperatures of specimens. These parameters were studied by optical microscopy, scanning electron microscopy, x-ray diffraction, and differential scanning calorimetry (DSC). Highly porous specimens were obtained with up to 83% total porosity and pore sizes between 300 and 500 μm in diameter. Results show pore characteristics were improved from anisotropic to isotropic and pore morphology was changed from channel-like to irregular by adding pore filler powders. Furthermore, the highly porous specimens produced when using urea as a space holder, were of more uniform composition in comparison to NaCl. DSC results showed that a two-step martensitic phase transformation takes place during the cooling cycles and the austenite finish temperature ( A f) is close to human body temperature. Compression test results reveal that the compressive strength of highly porous NiTi is about 155 MPa and recoverable strain about 6% in superelasticity regime.

Physicochemical Properties of Meat Batter Added with Edible Silkworm Pupae (Bombyx mori) and Transglutaminase.

PubMed

Park, Yoo-Sun; Choi, Yun-Sang; Hwang, Ko-Eun; Kim, Tae-Kyung; Lee, Cheol-Won; Shin, Dong-Min; Han, Sung Gu

2017-01-01

This study was conducted to investigate the physicochemical properties of meat batters prepared with fresh pork meat, back fat, water, and salt and formulated with three different amounts (5%, 10%, and 15%) of silkworm pupae ( Bombyx mori ) powder and transglutaminase (TG). Meat batters formulated with silkworm pupae powder showed significantly higher contents of protein and ash than control batter. Addition of silkworm pupae to batter also showed significantly lower cooking loss than the control. Moreover, meat batter containing 15% silkworm pupae showed no significant difference in redness value compared to the control. In addition, pH, viscosity, hardness, gumminess, and chewiness were improved after the addition of silkworm pupae. Furthermore, meat batter formulated with TG and silkworm pupae showed improved hardness, gumminess, chewiness and viscosity compared to control batter. Addition of 1% TG with 15% silkworm pupae to meat batter resulted in significantly higher pH, textures, and viscosity. Our data suggest that both silkworm pupae and TG can be added to meat batter to improve its physicochemical properties. Therefore, combination of silkworm pupae and TG could be a new nutritional and functional source for meat products.

Physicochemical Properties of Meat Batter Added with Edible Silkworm Pupae (Bombyx mori) and Transglutaminase

PubMed Central

Choi, Yun-Sang

2017-01-01

This study was conducted to investigate the physicochemical properties of meat batters prepared with fresh pork meat, back fat, water, and salt and formulated with three different amounts (5%, 10%, and 15%) of silkworm pupae (Bombyx mori) powder and transglutaminase (TG). Meat batters formulated with silkworm pupae powder showed significantly higher contents of protein and ash than control batter. Addition of silkworm pupae to batter also showed significantly lower cooking loss than the control. Moreover, meat batter containing 15% silkworm pupae showed no significant difference in redness value compared to the control. In addition, pH, viscosity, hardness, gumminess, and chewiness were improved after the addition of silkworm pupae. Furthermore, meat batter formulated with TG and silkworm pupae showed improved hardness, gumminess, chewiness and viscosity compared to control batter. Addition of 1% TG with 15% silkworm pupae to meat batter resulted in significantly higher pH, textures, and viscosity. Our data suggest that both silkworm pupae and TG can be added to meat batter to improve its physicochemical properties. Therefore, combination of silkworm pupae and TG could be a new nutritional and functional source for meat products. PMID:28747820

To determine the end point of wet granulation by measuring powder energies and thermal properties.

PubMed

Dave, Rutesh H; Wu, Stephen H; Contractor, Labdhi D

2012-04-01

Wet granulation has been widely used in pharmaceutical industry as a tablet manufacturing process. However, end-point determination of wet granulation process has always remained a challenge. Many traditional methods are available for end-point determination, yet accuracy and reproducibility still remain a challenge. Microcrystalline cellulose, widely used as an excipient in pharmaceutical industry, was granulated using water. Wet mass was passed through sieve # 12 and dried till constant percentage loss on drying was obtained and dried granules were obtained. Wet and dried granules collected were subjected to basic flow energy, specific energy, bulk density, pressure drop, differential scanning calorimetry and effusivity measurements. Analysis of data revealed various stages of granule growth from initial seed formation by adding 200-400 g of water, granule growth was observed by adding 600-800 g of water and over wetting was observed at 1155 g of water. In this work, we have justified our work to properly identify and utilize this technique for practical purpose to correctly identify the end-point determination of microcrystalline cellulose and explain various principles underlying energies associated with powder and thermal measurements.

Spore powder of Ganoderma lucidum for the treatment of Alzheimer disease: A pilot study.

PubMed

Wang, Guo-Hui; Wang, Li-Hua; Wang, Chen; Qin, Li-Hong

2018-05-01

This study explored the feasible efficacy and safety of the Spore Powder of Ganoderma Lucidum (SPGL) for treating patients with Alzheimer disease (AD). Forty-two eligible patients with AD were recruited. These patients were randomly allocated to an intervention group and a control group equally. The patients in the intervention group underwent SPGL, whereas the subjects in the control received placebo. All patients were treated for a total of 6 weeks. The primary outcome was measured by Alzheimer's disease Assessment Scale-Cognitive (ADAS-cog). The secondary outcomes were measured by the World Health Organization Quality of Life questionnaire (WHOQOL-BREF) and Neuropsychiatric Index (NPI). The adverse events were also recorded during the treatment period. At the end of the treatment, GLSP did not show more encouraging outcomes in symptoms improvement, measured by the ADAS-cog (P = .31), and NPI (P = .79); and quality of life enhancement, measured by the WHOQOL-BREF (physical, P = .62; psychological, P = .69; social relationships, P = .75; environment, P = .82; overall quality of life, P = .74), compared with the control group. In addition, all adverse events were mild, and no significant differences were found between 2 groups. The results of this study did not find the promising efficacy of SPGL for the treatment of AD after 6-week treatment. It may be because of the relative short-term of intervention. Future clinical trials with larger sample size and longer treatment period are urgently needed.

Studies on the reuse of waste printed circuit board as an additive for cement mortar.

PubMed

Ban, Bong-Chan; Song, Jong-Yoon; Lim, Joong-Yeon; Wang, Soo-Kyoon; An, Kwang-Guk; Kim, Dong-Su

2005-01-01

The recent development in electronic industries has generated a drastic increase in production of printed circuit boards (PCB). Accordingly, the amount of waste PCB from electronic productions and waste electronics and its environmental impact such as soil and groundwater contamination have become a great concern. This study aims to propose a method for reuse of waste PCB as an additive for cement mortar. Although the expansibility of waste PCB powder finer than 0.08 mm in water was observed to be greater than 2.0%, the maximum expansion rates in water for 0.08 to approximately 0.15 and 0.15 to approximately 0.30 mm sized PCB powders were less than 2.0%, which satisfied the necessary condition as an alternative additive for cement mortar in place of sand. The difference in the compressive strength of standard mortar and waste PCB added mortar was observed to be less than 10% and their difference was expected to be smaller after prolonged aging. The durability of waste PCB added cement mortar was also examined through dry/wet conditioning cyclic tests and acidic/alkaline conditioning tests. From the tests, both weight and compressive strength of cement mortar were observed to be recovered with aging. The leaching test for heavy metals from waste PCB added mortar showed that no heavy metal ions such as copper, lead, or cadmium were detected in the leachate, which resulted from fixation effect of the cement hydrates.

In Situ Fringe Projection Profilometry for Laser Power Bed Fusion Process

NASA Astrophysics Data System (ADS)

Zhang, Bin

Additive manufacturing (AM) offers an industrial solution to produce parts with complex geometries and internal structures that conventional manufacturing techniques cannot produce. However, current metal additive process, particularly the laser powder bed fusion (LPBF) process, suffers from poor surface finish and various material defects which hinder its wide applications. One way to solve this problem is by adding in situ metrology sensor onto the machine chamber. Matured manufacturing processes are tightly monitored and controlled, and instrumentation advances are needed to realize this same advantage for metal additive process. This encourages us to develop an in situ fringe projection system for the LPBF process. The development of such a system and the measurement capability are demonstrated in this dissertation. We show that this system can measure various powder bed signatures including powder layer variations, the average height drop between fused metal and unfused powder, and the height variations on the fused surfaces. The ability to measure textured surface is also evaluated through the instrument transfer function (ITF). We analyze the mathematical model of the proposed fringe projection system, and prove the linearity of the system through simulations. A practical ITF measurement technique using a stepped surface is also demonstrated. The measurement results are compared with theoretical predictions generated through the ITF simulations.

Fabrication of piezoelectric ceramic fibers by extrusion of PZT powder and PZT sol mixture

NASA Astrophysics Data System (ADS)

Kobayashi, Yoshimasa; Um, Tae Y.; Qiu, Jinhao; Tani, Junji; Takahashi, Hirofumi

2001-07-01

This study aims to fabricate Pb(Zr,Ti)O3 (PZT) piezoelectric ceramic fibers by extrusion with mixture of PZT powder and PZT sol. The added PZT sol in this study played a role as a binder; the sol changed into PZT crystalline during sintering, and removal process of additives before sintering was not required. To obtain PZT fibers, the condition of sol viscosity adjustment, the mixture ratio of powder and sol for fiber extrusion, and the sintering condition for obtaining polycrystalline fibers were investigated. PZT precursor solution was synthesized from lead acetate trihydrate, zirconium n-propoxide and titanium isopropoxide by reflux at 120 degree(s)C for 3 hours with 2-methoxyethanol. The appropriate adjustment of spinnable sol was achieved by the addition of acetic acid for suppressing the hydrolysis reaction and the curing sol at 80 degree(s)C for promoting the condensation of sol. Green fibers with diameter of about 300micrometers were successfully extruded from the mixture of PZT powder and sol. The extruded fibers sintered at 1200 degree(s)C had the microstructure with 2-6micrometers grains and had no pores or cracks. From the result of displacement behavior measurement, PZT fibers fabricated by firing at 1200 degree(s)C in this study were considered to have desired piezoelectric properties.

Application of the powder of porous titanium carbide ceramics to a reusable adsorbent for environmental pollutants.

PubMed

Moriwaki, Hiroshi; Kitajima, Shiori; Shirai, Koji; Kiguchi, Kenji; Yamada, Osamu

2011-01-30

The aim of this study is to investigate the utilization of the powder of porous titanium carbide (TiC) ceramics as a novel adsorbent or a material for solid-phase extraction (SPE). The adsorption and elution of inorganic and organic pollutants, Pb(II), 2,4,6-trichlorophenol (TCP), perfluorooctane sulfonate (PFOS), and perfluorooctanoic acid (PFOA), to the material were evaluated. The cartridge packed with TiC ceramics powder was used for the extraction test of pollutants. The solution containing pollutants at 1.0 μg mL(-1) was passed through the TiC cartridge, and the substances were almost quantitatively removed. Furthermore, the pollutants retained in the cartridge were eluted with 3N HCl for Pb(II) and with methanol for organic pollutants. The recoveries of pollutants were over 80%. In addition, we used the TiC cartridge for the solid-phase extraction of water samples (500 mL each of the distilled water and the river water) by adding pollutants at determined concentrations. Every pollutant was adsorbed almost quantitatively, and eluted by 3N HCl or methanol. From these results, we concluded that the powder of porous TiC ceramics is a useful reusable adsorbent for the water cleanup and solid-phase extraction. Copyright © 2010 Elsevier B.V. All rights reserved.

Incorporation of Rubber Powder as Filler in a New Dry-Hybrid Technology: Rheological and 3D DEM Mastic Performances Evaluation

PubMed Central

Vignali, Valeria; Mazzotta, Francesco; Sangiorgi, Cesare; Simone, Andrea; Lantieri, Claudio; Dondi, Giulio

2016-01-01

In recent years, the use of crumb rubber as modifier or additive within asphalt concretes has allowed obtaining mixtures able to bind high performances to recovery and reuse of discarded tires. To date, the common technologies that permit the reuse of rubber powder are the wet and dry ones. In this paper, a dry-hybrid technology for the production of Stone Mastic Asphalt mixtures is proposed. It allows the use of the rubber powder as filler, replacing part of the limestone one. Fillers are added and mixed with a high workability bitumen, modified with SBS (styrene-butadiene-styrene) polymer and paraffinic wax. The role of rubber powder and limestone filler within the bituminous mastic has been investigated through two different approaches. The first one is a rheological approach, which comprises a macro-scale laboratory analysis and a micro-scale DEM simulation. The second, instead, is a performance approach at high temperatures, which includes Multiple Stress Creep Recovery tests. The obtained results show that the rubber works as filler and it improves rheological characteristics of the polymer modified bitumen. In particular, it increases stiffness and elasticity at high temperatures and it reduces complex modulus at low temperatures. PMID:28773965

Premixed calcium silicate cement for endodontic applications

PubMed Central

Persson, Cecilia; Engqvist, Håkan

2011-01-01

Calcium silicate-based materials (also called MTA) are increasingly being used in endodontic applications. However, the handling properties of MTA are not optimal when it comes to injectability and cohesion. Premixing the cements using glycerol avoids these issues. However, there is a lack of data on the effect of common cement variables on important properties of premixed cements for endodontic applications. In this study, the effects of liquid-to-powder ratio, amount of radiopacifier and amount of calcium sulfate (added to control the setting time) were screened using a statistical model. In the second part of the study, the liquid-to-powder ratio was optimized for cements containing three different amounts of radiopacifier. Finally, the effect of using glycerol rather than water was evaluated in terms of radiopacity. The setting time was found to increase with the amount of radiopacifier when the liquid-to-powder ratio was fixed. This was likely due to the higher density of the radiopacifier in comparison to the calcium silicate, which gave a higher liquid-to-powder ratio in terms of volume. Using glycerol rather than water to mix the cements led to a decrease in radiopacity of the cement. In conclusion, we were able to produce premixed calcium silicate cements with acceptable properties for use in endodontic applications. PMID:23507729

Premixed calcium silicate cement for endodontic applications: injectability, setting time and radiopacity.

PubMed

Persson, Cecilia; Engqvist, Håkan

2011-01-01

Calcium silicate-based materials (also called MTA) are increasingly being used in endodontic applications. However, the handling properties of MTA are not optimal when it comes to injectability and cohesion. Premixing the cements using glycerol avoids these issues. However, there is a lack of data on the effect of common cement variables on important properties of premixed cements for endodontic applications. In this study, the effects of liquid-to-powder ratio, amount of radiopacifier and amount of calcium sulfate (added to control the setting time) were screened using a statistical model. In the second part of the study, the liquid-to-powder ratio was optimized for cements containing three different amounts of radiopacifier. Finally, the effect of using glycerol rather than water was evaluated in terms of radiopacity. The setting time was found to increase with the amount of radiopacifier when the liquid-to-powder ratio was fixed. This was likely due to the higher density of the radiopacifier in comparison to the calcium silicate, which gave a higher liquid-to-powder ratio in terms of volume. Using glycerol rather than water to mix the cements led to a decrease in radiopacity of the cement. In conclusion, we were able to produce premixed calcium silicate cements with acceptable properties for use in endodontic applications.

Comparative facies formation in selected coal beds of the Powder River Basin

USGS Publications Warehouse

Stanton, R.W.; Moore, Timothy A.; Warwick, Peter D.; Crowley, S.S.; Flores, Romeo M.; Flores, Romeo M.; Warwick, Peter D.; Moore, Timothy A.; Glass, Gary; Smith, Archie; Nichols, Douglas J.; Wolfe, Jack A.; Stanton, Ronald W.; Weaver, Jean

1989-01-01

Petrologic studies of thick coal beds [Warwick, 1985; Moore, 1986; Moore and others, 1986; Moore and others, 1987; Warwick and Stanton, in press], which build on sedimentological interpretations [Flores, this volume] of associated units, provide data to interpret and contrast the varieties of peat formation in the Powder River Basin. Detailed analyses of the composition of coal beds lead to more complete interpretations regarding the depositional environment on a regional and local scale. Our efforts in the Powder River Basin [areas A-D in fig. 1 of Flores, this volume] have resulted in a series of site-specific studies that interpret the types of peat formation from the arrangement of different facies which comprise the coal beds and from the spatial form of the coal beds.Our approach was to use a combination of megascopic criteria for facies sampling, and where only core was available, to analyze many interval samples to discriminate facies by their maceral composition. Coal beds in the Powder River Basin are composed of laterally continuous, compositional subunits of the bed (facies) that can be discerned most easily in weathered highwall exposures, less readily in fresh highwalls, and very poorly in fresh-cut core surfaces. In general, very low ash ( 

Design of Natural Hydroxyapatite as bio-composite ceramics (HAP): Experimental and Numerical Study

NASA Astrophysics Data System (ADS)

Belghazi, Z.; Katundi, D.; Ayari, F.; Bayraktar, E.

2011-01-01

Hydroxyapatite (HAP—Ca10(PO4)6 (OH)2), which exhibits excellent biocompatibility in the body, is one of the most widely used bioactive ceramics for biomedical applications. Along with the ability to carry the load, one of the most important properties of materials used for bone replacement is biocompatibility. In fact, HAP is a bioactive material and it can incorporate into bone structures, supporting bone in-growth without breaking down or dissolving, and it interacts with the living tissue due to the presence of free calcium and phosphate compounds. Generally, Al2O3 powder is added to HAP powder in order to obtain high fracture toughness. Al2O3 has good mechanical properties as compared with HAP, and exhibits extremely high stability with human tissues [1-6]. In this paper, the effect of microwave sintering temperature on the relative density, hardness, and phase purity of compacted bovine Hydroxyapatite (BHA) powder was reported. This research is a comprehensive attempt to develop Hydroxyapatite bio composite ceramics reinforced with alumina—Al2O3, pure titanium and pure pulverised boron powder. A Finite Element (FEM) analysis is also used for modelling to simulate the macroscopic behaviour of this material, taking into account the relevant microscopic scales.

Strain Hardening Behaviour and Its Effect on Properties of ZrB2 Reinforced Al Composite Prepared by Powder Metallurgy Technique

NASA Astrophysics Data System (ADS)

Kaku, Sai Mahesh Yadav; Khanra, Asit Kumar; Davidson, M. J.

2018-04-01

Strain hardening behaviour has significant effect on altering the properties of materials. In the present study, Al-ZrB2 metal matrix composites are made through powder metallurgy route. Incremental weight percentage (wt%) of ZrB2 (0, 2, 4 and 6 wt%) are added to Aluminium matrix to produce different composites. The homogenous powder mixture is compacted and pressurelessly sintered. Sintering of composites is performed over a range of 450-575 °C. The optimized sintered condition is observed at 550 °C for 1 h in controlled atmosphere (argon gas flow). The sintered compacts are strained in incremental steps in different levels up to failure. A visible crack on the bulge of the powder preform is considered as the failure. Composites are strain hardened up to failure. To evaluate the effect of temperature on strain hardening, strain hardening is carried out at different temperatures. Composites are densified with the extent of straining and hardness increases with the increase of strain. Hardness increase with the increase in temperature is maintained during strain hardening. To evaluate the corrosion behaviour of Al-ZrB2 composite, potentiodynamic polarization study are performed on the strained composites. Corrosion rate decrease with the extent of straining.

Antihemolytic and antioxidant properties of pearl powder against 2,2'-azobis(2-amidinopropane) dihydrochloride-induced hemolysis and oxidative damage to erythrocyte membrane lipids and proteins.

PubMed

Yang, Hsin-Ling; Korivi, Mallikarjuna; Lin, Ming-Kuem; Chang, Hebron Chun-Wei; Wu, Chi-Rei; Lee, Meng-Shiou; Chen, William Tzu-Liang; Hseu, You-Cheng

2017-10-01

Pearl powder, a well-known traditional mineral medicine, is reported to be used for well-being and to treat several diseases from centuries in Taiwan and China. We investigated the in vitro antihemolytic and antioxidant properties of pearl powder that could protect erythrocytes against 2,2'-azobis(2-amidinopropane) dihydrochloride (AAPH)-induced oxidative damage to membrane proteins/lipids. Human erythrocytes were incubated with different concentrations of pearl powder (50-200 μg/mL) for 30 minutes and then exposed to AAPH for 2-6 hours. We found that AAPH alone time dependently increased the oxidative hemolysis of erythrocytes, while pearl powder pretreatment substantially inhibited the hemolysis in a concentration-/time-dependent manner. AAPH-induced oxidative damage to erythrocyte membrane lipids was evidenced by the elevated malondialdehyde (MDA) levels. However, pearl powder remarkably inhibited the malondialdehyde formation, and the 200 μg/mL concentration showed almost similar malondialdehyde values to the control. Furthermore, pearl powder suppressed the AAPH-induced high-molecular-weight protein formation and concomitantly increased the low-molecular-weight proteins in erythrocytes. Antioxidant potential that was measured as superoxide dismutase activity and glutathione content was significantly dropped by AAPH incubation, which suggests the vulnerability of erythrocytes to AAPH-induced oxidative stress. Noteworthy, erythrocytes pretreated with pearl powder showed restored superoxide dismutase activity and glutathione levels against AAPH-induced loss. Our findings conclude that pearl powder attenuate free radical-induced hemolysis and oxidative damage to erythrocyte membrane lipids/proteins. The potent antioxidant property of pearl powder may offer protection from free radical-related diseases. Copyright © 2016. Published by Elsevier B.V.

Metal-Rich Transition Metal Diborides as Electrocatalysts for Hydrogen Evolution Reactions in a Wide Range of pH

DOE PAGES

Sitler, Steven J.; Raja, Krishnan S.; Charit, Indrajit

2016-09-23

Solid solutions of HfB 2-ZrB 2 mixtures were prepared by high-energy ball milling of diboride and additive powders followed by spark plasma sintering (SPS). A mixture of stoichiometric 1:1 HfB 2-ZrB 2 borides was the base composition to which Hf, Zr, Ta, LaB 6 or Gd 2O 3 was added. Hf, Zr and Ta were added in order to bring the boron-to-metal ratio down to 1.86, rendering the boride as MeB 1.86. In the case of LaB 6 and Gd 2O 3, 1.8 mol% was added. Electroanalytical behavior of hydrogen evolution reactions was evaluated in 1 M H 2SO 4more » and 1 M NaOH solutions. The LaB 6 additive material showed Tafel slopes of 125 and 90 mV/decade in acidic and alkaline solutions respectively. The Hf and Zr rich samples showed Tafel slopes of about 120 mV/decade in both electrolytes. The over potentials of hydrogen evolution reactions (at 10 mA/cm 2) in the alkaline solution were about 100 mV lower than those in acidic solution. The metal-rich diborides and addition of LaB 6 showed better hydrogen evolution reaction (HER) activities than the base 1:1 HfB 2-ZrB 2 stoichiometric diboride solid solution. Furthermore, the higher activity of metal-rich borides could be attributed to the increased electron population at the d-orbitals of the metal shown by band structure modeling calculations using the Density Functional Theory approach.« less

Tailored Core Shell Cathode Powders for Solid Oxide Fuel Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swartz, Scott

2015-03-23

In this Phase I SBIR project, a “core-shell” composite cathode approach was evaluated for improving SOFC performance and reducing degradation of lanthanum strontium cobalt ferrite (LSCF) cathode materials, following previous successful demonstrations of infiltration approaches for achieving the same goals. The intent was to establish core-shell cathode powders that enabled high performance to be obtained with “drop-in” process capability for SOFC manufacturing (i.e., rather than adding an infiltration step to the SOFC manufacturing process). Milling, precipitation and hetero-coagulation methods were evaluated for making core-shell composite cathode powders comprised of coarse LSCF “core” particles and nanoscale “shell” particles of lanthanum strontiummore » manganite (LSM) or praseodymium strontium manganite (PSM). Precipitation and hetero-coagulation methods were successful for obtaining the targeted core-shell morphology, although perfect coverage of the LSCF core particles by the LSM and PSM particles was not obtained. Electrochemical characterization of core-shell cathode powders and conventional (baseline) cathode powders was performed via electrochemical impedance spectroscopy (EIS) half-cell measurements and single-cell SOFC testing. Reliable EIS testing methods were established, which enabled comparative area-specific resistance measurements to be obtained. A single-cell SOFC testing approach also was established that enabled cathode resistance to be separated from overall cell resistance, and for cathode degradation to be separated from overall cell degradation. The results of these EIS and SOFC tests conclusively determined that the core-shell cathode powders resulted in significant lowering of performance, compared to the baseline cathodes. Based on the results of this project, it was concluded that the core-shell cathode approach did not warrant further investigation.« less

Effects of glucose and sucrose variants of the caries-promoting Diet 2000 on the feeding patterns and parotid glands of prematurely weaned rats.

PubMed

Redman, Robert S

2015-03-01

The hypothesis of this study was that feeding glucose instead of sucrose in the cariogenic Diet 2000 to rats weaned at age 18 days would result in greater light/dark differences in feeding activity and secretion and storage of parotid salivary enzymes. Diet 2000 and a stock commercial diet (controls) were prepared in pelleted and powdered forms, as the increased mastication required by pellets has been shown to support circadian rhythms in rats. Food jars were weighed at lights on and just prior to lights off daily. Rats were euthanized at 25 days and their parotid glands removed, weighed, and analyzed for specific activities of the salivary enzymes α-amylase and deoxyribonuclease I. Light/dark differences in feeding activity were strong in the rats fed the pelleted stock diet and both powdered and pelleted glucose 2000 diets, moderate with the pelleted sucrose 2000 diet, and not significant with the powdered sucrose 2000 and stock diets. Light/dark differences in the parotid salivary enzymes were strong with the powdered glucose 2000 diet and the pelleted forms of the glucose and sucrose 2000 and stock diets, and not significant with the powdered stock and sucrose 2000 diets. Caries reportedly is higher in sucrose than glucose fed to rats in the standard powdered form of Diet 2000, mainly due to the colonizing advantage Streptococcus mutans gains with sucrose. These results suggest that additional factors are more feeding during lights on and less stimulation of parotid salivary secretion with the sucrose powder. Published by Elsevier Ltd.

Inhibitory effect of Patrinia scabiosifolia Link on the development of atopic dermatitis-like lesions in human keratinocytes and NC/Nga mice.

PubMed

Cha, Kyung-Jae; Im, Mi Ae; Gu, Ayoung; Kim, Da Hye; Lee, Daye; Lee, Jeong Soo; Lee, Ji-Sook; Kim, In Sik

2017-07-12

Atopic dermatitis (AD) is a chronic pruritic and inflammatory disease occurring in skin. Patrinia scabiosifolia Link (PS), a member of the Patrinia genus (Caprifoliaceae family), has traditionally been used in folk medicines to treat various inflammatory diseases such as acute appendicitis, ulcerative colitis, and pelvic inflammation in Korea and other parts of East Asia. This study investigated the anti-inflammatory effects of PS on AD in vitro and in vivo. Whole PS plants were dried, powdered, and then underwent extraction with DMSO. Both ELISA and western blotting were performed to evaluate cytokine concentration and the expression and activation of filaggrin and signaling proteins. Five-week-old female NC/Nga mice were used as an AD-like mouse model by treating them with 2,4-dinitrochlorobenzene (DNCB). In human keratinocytic HaCaT cells, PS extract inhibited the production of IL-8, and TARC, which had been increased by TNF-α and IFN-γ. The TNF-α and IFN-γ suppressed filaggrin expression was associated with phosphorylation of JNK1 and JNK2, and NF-κB translocation. PS recovered the inhibition of filaggrin expression induced by TNF-α and IFN-γ by blocking the activation of JNK1/2, and NF-κB by the IFN-γ and TNF-α treatment. The in vivo experiment results showed that, compared to DNCB treatment PS administration reduced thickening of the epidermis and infiltration of inflammatory cells into the dermis. Moreover, the decrease of filaggrin expression due to DNCB treatment was recovered by PS administration. The serum IgE level was decreased by PS treatment. Additionally, secretions of IL-4, IL-5, IL-13, and eotaxin in splenocytes were lower in the PS-treated group than in the DNCB group. PS may attenuate the development of AD-like lesions by increasing filaggrin expression and lowering IgE and inflammatory cytokine levels. These results indicate the potential for development of a PS-based drug treatment for AD. Copyright © 2017. Published by Elsevier B.V.

Stimulation of processes of self-propagating high temperature synthesis in system Ti + Al at low temperatures by influence of γ-quanta

NASA Astrophysics Data System (ADS)

Sobachkin, A. V.; Loginova, M. V.; Sitnikov, A. A.; Yakovlev, V. I.; Filimonov, V. Yu; Gradoboev, A. V.

2018-03-01

In the present work, the influence of the irradiation with gamma-quanta 60Co upon the structural and phase state of the components of the mechanically activated powder composition of Ti+Al is investigated. The phase composition, structural parameters, and crystallinity are examined by means of X-ray diffractometry. It is found out that the irradiation with gamma-quanta changes the structure of the mechanically activated powder composition. The higher irradiation dose, the higher the structure crystallinity of both components with no change in phase state. At the same time, the parameters of Ti and Al crystal lattices approach to the initial parameters observed before the mechanical activation. The irradiation with gammaquanta leads to decrease of internal stresses in the mechanically activated powder composition while nanocrystallinity of the structure remains unchanged. Using of powder compositions exposed to the irradiation with gamma-quanta for the SH-synthesis helps to increase speed of the reaction, decrease the peak firing temperature and improve homogeneity, as well as the main phase of the produced material is TiAl.

Evaluation of different drying temperatures on physico-chemical and antioxidant properties of water-soluble tomato powders and on their use in pork patties.

PubMed

Kim, Hyeong Sang; Chin, Koo Bok

2016-02-01

Tomato and tomato products provide various antioxidant activities, which could be changed by the processing method. This study was performed to evaluate the antioxidant activity of water-soluble tomato powder (WSTP) as affected by different oven temperatures (60, 80 and 100°C), and to evaluate the physico-chemical properties and antioxidative activities of pork patties containing these powders. The contents of total phenolic compounds of WSTP ranged from 22.2 to 69.6 g kg(-1) dry matter. The antioxidant activities increased significantly with increasing drying temperatures (P < 0.05). The physico-chemical properties of pork patties containing tomato powders were also evaluated. WSTP at 100°C showed the highest redness value compared to those dried at 60 and 80°C. Lipid oxidation of pork patties was retarded by 7 days with the addition of WSTP. In particular, pork patties containing WSTP showed antimicrobial activity at 14 days of refrigerated storage, regardless of drying temperatures. WSTP, especially prepared at 100°C, could be used as a natural antioxidant and antimicrobial agent in meat products. © 2015 Society of Chemical Industry.

A novel approach for mitigation of membrane fouling: Concomitant use of flocculant and magnetic powder.

PubMed

Wang, Hongyu; Chen, Zhouzhou; Miao, Jia; Li, Yaozhong

2016-06-01

Membrane fouling alleviation by addition of poly dimethyl diallyl ammonium chloride (PDMDAAC) and magnetic powder (Fe3O4) was investigated. It was found that magnetic powder associated with PDMDAAC had a good performance on mitigation of membrane fouling, improvement in dehydrogenase activity and enhancement of biomass growth. The optimal dose of PDMDAAC was determined by using constant pressure dead-end filtration unit. Maximum permeate flux was attained at 400mg/L of PDMDAAC addition. Continuous experiment was conducted in a submerged membrane bioreactor (MBR) system and biomass parameters such as soluble microbial products (SMP), extracellular polymeric substances (EPS), dehydrogenase activity, zeta potential, and capillary suction time (CST) were analyzed. Best results were obtained with a combination of 120mg/L of magnetic powder and 400mg/L of PDMDAAC. This study results demonstrated that PDMDAAC played a major role in SMPc and EPSc reduction, whereas magnetic powder had better performance in decreasing SMPc and EPSp. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparative antipyretic and analgesic activities of Cissampelos pareira Linn. and Cyclea peltata (Lam.) Hook. F. & Thomas.

PubMed

Singh, Suman G; Nishteswar, K; Patel, Bhupesh R; Nariya, Mukesh

2016-01-01

Cissampelos pareira Linn. is considered as an established source of Patha , whereas Cyclea peltata (Lam.) Hook. F. & Thomas is used as a source plant of Patha in the southern part of India. In classical texts, two different varieties of Patha , i.e. Rajpatha ( C. peltata ) and Laghupatha ( C. pareira ), are mentioned which possess almost similar properties. To compare antipyretic and analgesic activities of C. pareira and C. peltata in suitable experimental model. Powder (540 mg/kg) and ethanolic extract (200 mg/kg) of both the test drugs ( C. pareira and C. peltata ) were evaluated for antipyretic activity in Brewer's yeast-induced pyrexia model in rats. Analgesic activity was evaluated by radiant heat model in rats and acetic acid-induced writhing syndrome in mice. Result of the present study had shown that powder of C. pareira (540 mg/kg) has moderate antipyretic activity as compared to the powder of C. peltata and extract of both test drugs. C. pareira powder showed better analgesic effect than ethanolic extract (200 mg/kg) of both the test drugs in radiant heat model in rats, while in acetic acid-induced writhing syndrome, ethanolic extract (280 mg/kg) of both drugs showed pronounced effect as compared to powder form (780 mg/kg) in mice. Both C. pareira and C. peltata exhibited analgesic effects in experimental animals. The effect is more significant in C. peltata treated group compared to C. pareira . Antipyretic effect was observed with the pretreatment of C. pareira .

Thermoset recycling via high-pressure high-temperature sintering: Revisiting the effect of interchange chemistry

NASA Astrophysics Data System (ADS)

Morin, Jeremy Edward

In 1844 Charles Goodyear obtained U.S. Patent #3,633 for his "Gum Elastic Composition". In a published circular, which describes his patent for the sulfur vulcanization of gum elastic composition, he stated: "No degree of heat, without blaze, can melt it (rubber)... It resists the most powerful chemical reagents. Aquafortis (nitric acid), sulphuric acid, essential and common oils, turpentine and other solvents... ..." Goodyear's sulfur vulcanization of rubber fueled much of the industrial revolution and made transportation possible, as it exists today. In doing so, Goodyear created one of the most difficult materials to recycle. Rubber will not melt, dissolve, or lend itself to the usual methods of chemical decomposition. Ironically, Goodyear recognized this problem and in 1853 he patented the process of adding ground rubber to virgin material, now currently known as regrind blending. Today, scrap tires represent one of the most serious sources of pollution in the world. Studies estimate that there are roughly 2 billion scrap tires in U.S. landfills and more are being added at a rate of over 273 million tires per year. Current methods of recycling waste tires are crude, ineffective, and use rubber powder as a low cost filler instead of a new rubber. The groundwork for a very simple and effective method of producing high-quality rubber goods using 100% scrap rubber was discovered in 1944 by A. V. Tobolsky et al. This application, however, was not recognized until recently in our laboratory. The process as studied to date represents a method of creating quality, high-value added rubber goods with nothing other than heat and pressure. High pressure is required to obtain a void-free compaction of the rubber particles by forcing all of the free surfaces into intimate contact. High temperature then activates the chemical rearrangement, scission, and reformation of the chemical bonds thus providing new bridges between the once fractured interfaces. This occurs both within and between particles. The technique of high-pressure high-temperature sintering has worked on all types of thermoset materials. Typical mechanical properties for sintered SBR powder rubber are as follows: 1.3 MPa 100% Modulus, 12.0 MPa Tensile Strength and 300% Elongation at Break. The goal of this research is two-fold. First, to gain an understanding of the variables that control the process of high-pressure high-temperature sintering. Second, to study the factors governing the mechanism of fusion with the hope of controlling and exploiting this process so that tires can be recycled to produce high quality and high-value added products.

Consumer acceptance and aroma characterization of navy bean (Phaseolus vulgaris) powders prepared by extrusion and conventional processing methods.

PubMed

Szczygiel, Edward J; Harte, Janice B; Strasburg, Gale M; Cho, Sungeun

2017-09-01

Food products produced with bean ingredients are gaining in popularity among consumers due to the reported health benefits. Navy bean (Phaseolus vulgaris) powder produced through extrusion can be considered as a resource-efficient alternative to conventional methods, which often involve high water inputs. Therefore, navy bean powders produced with extrusion and conventional methods were assessed for the impact of processing on consumer liking in end-use products and odor-active compounds. Consumer acceptance results reveal significant differences in flavor, texture and overall acceptance scores of several products produced with navy bean powder. Crackers produced with extruded navy bean powder received higher hedonic flavor ratings than those produced with commercial navy bean powder (P < 0.001). GC-O data showed that the commercial powder produced through conventional processing had much greater contents of several aliphatic aldehydes commonly formed via lipid oxidation, such as hexanal, octanal and nonanal with descriptors of 'grassy', 'nutty', 'fruity', 'dusty', and 'cleaner', compared to the extruded powder. Extrusion processed navy bean powders were preferred over commercial powders for certain navy bean powder applications. This is best explained by substantial differences in aroma profiles of the two powders that may have been caused by lipid oxidation. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Oily wastewater treatment by adsorption-membrane filtration hybrid process using powdered activated carbon, natural zeolite powder and low cost ceramic membranes.

PubMed

Rasouli, Yaser; Abbasi, Mohsen; Hashemifard, Seyed Abdollatif

2017-08-01

In this research, four types of low cost and high performance ceramic microfiltration (MF) membranes have been employed in an in-line adsorption-MF process for oily wastewater treatment. Mullite, mullite-alumina, mullite-alumina-zeolite and mullite-zeolite membranes were fabricated as ceramic MF membranes by low cost kaolin clay, natural zeolite and α-alumina powder. Powdered activated carbon (PAC) and natural zeolite powder in concentrations of 100-800 mg L -1 were used as adsorbent agent in the in-line adsorption-MF process. Performance of the hybrid adsorption-MF process for each concentration of PAC and natural zeolite powder was investigated by comparing quantity of permeation flux (PF) and total organic carbon (TOC) rejection during oily wastewater treatment. Results showed that by application of 400 mg L -1 PAC in the adsorption-MF process with mullite and mullite-alumina membranes, TOC rejection was enhanced up to 99.5% in comparison to the MF only process. An increasing trend was observed in PF by application of 100-800 mg L -1 PAC. Also, results demonstrated that the adsorption-MF process with natural zeolite powder has higher performance in comparison to the MF process for all membranes except mullite-alumina membranes in terms of PF. In fact, significant enhancement of PF and TOC rejection up to 99.9% were achieved by employing natural zeolite powder in the in-line adsorption-MF hybrid process.

Detailed kinetics of titanium nitride synthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rode, H.; Hlavacek, V.

1995-02-01

A thermogravimetric analyzer is used to study the synthesis of TiN from Ti powder over a wide range of temperature, conversion and heating rate, and for two Ti precursor powders with different morphologies. Conversions to TiN up to 99% are obtained with negligible oxygen contamination. Nonisothermal initial rate and isothermal data are used in a nonlinear least-squares minimization to determine the most appropriate rate law. The logarithmic rate law offers an excellent agreement between the experimental and calculated conversions to TiN and can predict afterburning, which is an important experimentally observed phenomenon. Due to the form of the logarithmic ratemore » law, the observed activation energy is a function of effective particle size, extent of conversion, and temperature even when the intrinsic activation energy remains constant. This aspect explains discrepancies among activation energies obtained in previous studies. The frequently used sedimentation particle size is a poor measure of the powder reactivity. The BET surface area indicates the powder reactivity much better.« less

Anti-obesity activity of Yamabushitake (Hericium erinaceus) powder in ovariectomized mice, and its potentially active compounds.

PubMed

Hiraki, Eri; Furuta, Shoko; Kuwahara, Rika; Takemoto, Naomichi; Nagata, Toshiro; Akasaka, Taiki; Shirouchi, Bungo; Sato, Masao; Ohnuki, Koichiro; Shimizu, Kuniyoshi

2017-07-01

Hericium erinaceus (H. erinaceus) improves the symptoms of menopause. In this study, using ovariectomized mice as a model of menopause, we investigated the anti-obesity effect of this mushroom in menopause. Mice fed diets containing H. erinaceus powder showed significant decreases in the amounts of fat tissue, plasma levels of total cholesterol, and leptin. To determine the mechanism, groups of mice were respectively fed a diet containing H. erinaceus powder, a diet containing ethanol extract of H. erinaceus, and a diet containing a residue of the extract. As a result, H. erinaceus powder was found to increase fecal lipid levels in excreted matter. Further in vitro investigation showed that ethanol extract inhibited the activity of lipase, and four lipase-inhibitory compounds were isolated from the extract: hericenone C, hericenone D, hericenone F, and hericenone G. In short, we suggest that H. erinaceus has an anti-obesity effect during menopause because it decreases the ability to absorb lipids.

Antioxidant Activity, Total Phenolics Content, Anthocyanin, and Color Stability of Isotonic Model Beverages Colored with Andes Berry (Rubus glaucus Benth) Anthocyanin Powder

PubMed Central

Estupiñan, D.C.; Schwartz, S.J.; Garzón, G.A.

2013-01-01

The stability of anthocyanin (ACN) freeze-dried powders from Andes berry (Rubus glaucus Benth) as affected by storage, addition of maltodextrin as a carrier agent, and illumination was evaluated in isotonic model beverages. The ethanolic ACN extract was freeze dried with and without maltodextrin DE 20. Isotonic model beverages were colored with freeze-dried ACN powder (FDA), freeze-dried ACN powder with maltodextrin (MFDA), and red nr 40. Beverages were stored in the dark and under the effect of illumination. Half life of the ACNs, changes in color, total phenolics content (TPC), and antioxidant activity were analyzed for 71 d. Addition of maltodextrin and absence of light stabilized the color of beverages and improved ACN and TPC stability during storage. The antioxidant activity of the beverages was higher when they were colored with MFDA and highly correlated with ACN content. There was no correlation between antioxidant activity and TPC. It is concluded that addition of maltodextrin DE 20 as a carrier agent during freeze-drying improves the color and stability of nutraceutical antioxidants present in Andes berry extract. This suggests a protective enclosing of ACNs within a maltodextrin matrix with a resulting powder that could serve as a supplement or additive to naturally color and to enhance the antioxidant capacity of isotonic beverages. PMID:21535712

Antioxidant activity, total phenolics content, anthocyanin, and color stability of isotonic model beverages colored with Andes berry (Rubus glaucus Benth) anthocyanin powder.

PubMed

Estupiñan, D C; Schwartz, S J; Garzón, G A

2011-01-01

The stability of anthocyanin (ACN) freeze-dried powders from Andes berry (Rubus glaucus Benth) as affected by storage, addition of maltodextrin as a carrier agent, and illumination was evaluated in isotonic model beverages. The ethanolic ACN extract was freeze dried with and without maltodextrin DE 20. Isotonic model beverages were colored with freeze-dried ACN powder (FDA), freeze-dried ACN powder with maltodextrin (MFDA), and red nr 40. Beverages were stored in the dark and under the effect of illumination. Half life of the ACNs, changes in color, total phenolics content (TPC), and antioxidant activity were analyzed for 71 d. Addition of maltodextrin and absence of light stabilized the color of beverages and improved ACN and TPC stability during storage. The antioxidant activity of the beverages was higher when they were colored with MFDA and highly correlated with ACN content. There was no correlation between antioxidant activity and TPC. It is concluded that addition of maltodextrin DE 20 as a carrier agent during freeze-drying improves the color and stability of nutraceutical antioxidants present in Andes berry extract. This suggests a protective enclosing of ACNs within a maltodextrin matrix with a resulting powder that could serve as a supplement or additive to naturally color and to enhance the antioxidant capacity of isotonic beverages.

Effect of mechanical activation on jell boronizing treatment of the AISI 4140

NASA Astrophysics Data System (ADS)

Yılmaz, S. O.; Karataş, S.

2013-06-01

The article presents the effect of mechanical activation on the growth kinetics of boride layer of boronized AISI 4140 steel. The samples were boronized by ferroboron + (SiO2-Na2O) powders for 873-1173 K temperature and 2, 4, 6 and 8 h times, respectively. The morphology and types of borides formed on the surface of AISI 4140 steel substrate were analyzed. Layer growth kinetics were analyzed by measuring the extent of penetration of FeB and Fe2B sublayers as function of treatment time and temperature in the range of 873-1173 K. High diffusivity was obtained by creating a large number of defects through mechanical activation in the form of nanometer sized crystalline particles through the repeated fracturing and cold-welding of the powder particles, and a depth of 100 μm was found in the specimen borided by the 2 h MA powders, for 4 h and 1073 K, where 2000-2350 HV were measured. Consequently, the application conditions of boronizing were improved by usage of mechanical activation. The preferred Fe2B boride without FeB could be formed in the boride layer under 973 K boronizing temperature by mechanically activated by ferroboron + sodium silicate powder mixture due to the decrease of the activation energy.

Effects of Processing and Storage on Pediococcus pentosaceus SB83 in Vaginal Formulations: Lyophilized Powder and Tablets

PubMed Central

Borges, Sandra; Costa, Paulo; Silva, Joana; Teixeira, Paula

2013-01-01

Vaginal probiotics have an important role in preventing the colonization of the vagina by pathogens. This study aimed to investigate different formulations with Pediococcus pentosaceus SB83 (lyophilized powder and tablets with and without retarding polymer) in order to verify its stability and antilisterial activity after manufacture and during storage. The bacteriocinogenic activity of P. pentosaceus SB83 against Listeria monocytogenes was evaluated in simulated vaginal fluid. Suspension of Pediococcus pentosaceus SB83 reduced the pathogen only after 2 h and the lyophilized bacteria after 24 h of contact, and, in the tablets, P. pentosaceus SB83 lost the antimicrobial activity. The pH of simulated vaginal fluid decreased for all the tested conditions. As lyophilized powder demonstrated better results concerning antimicrobial activity, this formulation was selected to evaluate the antilisterial activity during the 12 months of storage. During storage at room temperature, lyophilized bacteria totally inhibited the pathogen only until one month of storage. At 4°C, P. pentosaceus SB83 showed antimicrobial activity during all the time of storage investigated. Therefore, the better formulation of P. pentosaceus SB83 is the lyophilized powder stored at 4°C, which may be administered intravaginally as a washing solution. PMID:23844367